GeoSEA: Geodetic Earthquake Observatory on the Seafloor

NASA Astrophysics Data System (ADS)

Kopp, Heidrun; Lange, Dietrich; Flueh, Ernst R.; Petersen, Florian; Behrmann, Jan-Hinrich; Devey, Colin

2014-05-01

Space geodetic observations of crustal deformation have contributed greatly to our understanding of plate tectonic processes in general, and plate subduction in particular. Measurements of interseismic strain have documented the active accumulation of strain, and subsequent strain release during earthquakes. However, techniques such as GPS cannot be applied below the water surface because the electromagnetic energy is strongly attenuated in the water column. Evidence suggests that much of the elastic strain build up and release (and particularly that responsible for both tsunami generation and giant earthquakes) occurs offshore. To quantify strain accumulation and assess the resultant hazard potential we urgently need systems to resolve seafloor crustal deformation. Here we report on first results of sea trials of a newly implemented seafloor geodesy array. The GeoSEA (Geodetic Earthquake Observatory on the Seafloor) array consists of a seafloor transponder network comprising 35 units and a wave glider acting as a surface unit (GeoSURF) to ensure satellite correspondence, data transfer and monitor system health. Seafloor displacement occurs in the horizontal (x,y) and vertical direction (z). The vertical displacement is measured by monitoring pressure variations at the seafloor. Horizontal seafloor displacement can be measured either using an acoustic/GPS combination to provide absolute positioning (requiring a suitably equipped vessel to perform repeated cruises to provide the GPS fixes) or by long-term acoustic telemetry between different beacons fixed on the seafloor to determine relative distances by using the travel time observations to each other, which is the technique tested during our short sea trials. For horizontal direct path measurements, the system utilizes acoustic ranging techniques with a ranging precision better than 15 mm and long term stability over 2 km distances. Vertical motion is obtained from pressure gauges. Integrated inclinometers monitor station settlement in two horizontal directions. Data can be acquired and recorded autonomously subsea without system or human intervention for up to 6 years. These data can then be recovered via the integrated high-speed acoustic telemetry link without recovering the seafloor units. When requested to do so, the stored data will be transmitted wirelessly up to the sea surface to the GeoSURF wave glider for onward transmission via a satellite link. Targets for GeoSEA are the marine sector of the North Anatolian fault zone in the Marmara Sea, where a joint French-German array will be installed in late 2014 as well as the central sector of the South America - Nazca convergent plate boundary along the Iquique segment, offshore Northern Chile. Here, the GeoSEA array will be installed in late 2015 to monitor crustal deformation. Mobile autonomous seafloor arrays for continuous measurement of active seafloor deformation in hazard zones have the potential to lead to transformative discoveries of plate boundary/fault zone tectonic processes and address a novel element of marine geophysical research.

Deformation offshore Northern Chile monitored by a seafloor geodetic network (GeoSEA)

NASA Astrophysics Data System (ADS)

Hannemann, Katrin; Lange, Dietrich; Kopp, Heidrun; Petersen, Florian; Contreras-Reyes, Eduardo

2017-04-01

The Nazca-South American plate boundary around 21°S has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique earthquake (Mw=8.1). The southern portion of this segment is still unbroken. The geodetic monitoring of the Chilean subduction zone is crucial to understand the deformation processes in this area. Most geodetic measurements rely on GPS and are therefore limited to onshore campaigns. In December 2015, we installed the GeoSEA (Geodetic Earthquake Observatory on the SEAfloor) array around 21°S of the Nazca-South American plate boundary with RV SONNE to extend the geodetic observations to the offshore areas. The GeoSEA array consists of autonomous acoustic seafloor transponders mounted on 4 m high tripods. These transponders are able to continuously measure the two-way travel time of acoustic signals between station pairs (baselines) and the properties of the sea water (sound speed, temperature and pressure) at each transponder. These measurements are used to retrieve the distances between the transponders and give insights into the deformation of the seafloor. At the Chilean subduction zone, we installed in total 23 transponders in 3 subarrays with interstation distances of up to 2500 m. On the middle continental slope in 2300 m water depth, an array consisting of 8 transponders measures across crustal faults seen in AUV mapping. A second array of 5 stations located on the outer rise monitors extension across normal plate-bending faults. The deepest deployment in 5000 m water depth located on the lower continental slope with 10 stations is designed to measure diffuse strain build-up. The transponders are intended to monitor the seafloor deformation for 3.5 years. In November 2016 during a cruise of RV Langseth, the first 11 months of data were successfully uploaded via an acoustic modem. Furthermore, an additional component of the network, GeoSURF, a self-steering autonomous vehicle (wave glider), was successfully used to monitor system health and to upload parts of the data from the seafloor stations. The first 11 months of data show a good signal quality and the baseline precision is ± 5 mm. The data reveals no deformation above the resolution limits of the individual distance measurements.

Azimuth selection for sea level measurements using geodetic GPS receivers

NASA Astrophysics Data System (ADS)

Wang, Xiaolei; Zhang, Qin; Zhang, Shuangcheng

2018-03-01

Based on analysis of Global Positioning System (GPS) multipath signals recorded by a geodetic GPS receiver, GPS Reflectometry (GPS-R) has demonstrated unique advantages in relation to sea level monitoring. Founded on multipath reflectometry theory, sea level changes can be measured by GPS-R through spectral analysis of recorded signal-to-noise ratio data. However, prior to estimating multipath parameters, it is necessary to define azimuth and elevation angle mask to ensure the reflecting zones are on water. Here, a method is presented to address azimuth selection, a topic currently under active development in the field of GPS-R. Data from three test sites: the Kachemak Bay GPS site PBAY in Alaska (USA), Friday Harbor GPS site SC02 in the San Juan Islands (USA), and Brest Harbor GPS site BRST in Brest (France) are analyzed. These sites are located in different multipath environments, from a rural coastal area to a busy harbor, and they experience different tidal ranges. Estimates by the GPS tide gauges at azimuths selected by the presented method are compared with measurements from physical tide gauges and acceptable correspondence found for all three sites.

EarthScope's Plate Boundary Observatory in Alaska: Building on Existing Infrastructure to Provide a Platform for Integrated Research and Hazard-monitoring Efforts

NASA Astrophysics Data System (ADS)

Boyce, E. S.; Bierma, R. M.; Willoughby, H.; Feaux, K.; Mattioli, G. S.; Enders, M.; Busby, R. W.

2014-12-01

EarthScope's geodetic component in Alaska, the UNAVCO-operated Plate Boundary Observatory (PBO) network, includes 139 continuous GPS sites and 41 supporting telemetry relays. These are spread across a vast area, from northern AK to the Aleutians. Forty-five of these stations were installed or have been upgraded in cooperation with various partner agencies and currently provide data collection and transmission for more than one group. Leveraging existing infrastructure normally has multiple benefits, such as easier permitting requirements and costs savings through reduced overall construction and maintenance expenses. At some sites, PBO-AK power and communications systems have additional capacity beyond that which is needed for reliable acquisition of GPS data. Where permits allow, such stations could serve as platforms for additional instrumentation or real-time observing needs. With the expansion of the Transportable Array (TA) into Alaska, there is increased interest to leverage existing EarthScope resources for station co-location and telemetry integration. Because of the complexity and difficulty of long-term O&M at PBO sites, however, actual integration of GPS and seismic equipment must be considered on a case-by-case basis. UNAVCO currently operates two integrated GPS/seismic stations in collaboration with the Alaska Earthquake Center, and three with the Alaska Volcano Observatory. By the end of 2014, PBO and TA plan to install another four integrated and/or co-located geodetic and seismic systems. While three of these are designed around existing PBO stations, one will be a completely new TA installation, providing PBO with an opportunity to expand geodetic data collection in Alaska within the limited operations and maintenance phase of the project. We will present some of the design considerations, outcomes, and lessons learned from past and ongoing projects to integrate seismometers and other instrumentation at PBO-Alaska stations. Developing the PBO network as a platform for ongoing research and hazard monitoring equipment may also continue to serve the needs of the research community and the public beyond the sun-setting and completion of EarthScope science plan in 2018.

Extending Resolution of Fault Slip With Geodetic Networks Through Optimal Network Design

NASA Astrophysics Data System (ADS)

Sathiakumar, Sharadha; Barbot, Sylvain Denis; Agram, Piyush

2017-12-01

Geodetic networks consisting of high precision and high rate Global Navigation Satellite Systems (GNSS) stations continuously monitor seismically active regions of the world. These networks measure surface displacements and the amount of geodetic strain accumulated in the region and give insight into the seismic potential. SuGar (Sumatra GPS Array) in Sumatra, GEONET (GNSS Earth Observation Network System) in Japan, and PBO (Plate Boundary Observatory) in California are some examples of established networks around the world that are constantly expanding with the addition of new stations to improve the quality of measurements. However, installing new stations to existing networks is tedious and expensive. Therefore, it is important to choose suitable locations for new stations to increase the precision obtained in measuring the geophysical parameters of interest. Here we describe a methodology to design optimal geodetic networks that augment the existing system and use it to investigate seismo-tectonics at convergent and transform boundaries considering land-based and seafloor geodesy. The proposed network design optimization would be pivotal to better understand seismic and tsunami hazards around the world. Land-based and seafloor networks can monitor fault slip around subduction zones with significant resolution, but transform faults are more challenging to monitor due to their near-vertical geometry.

Kinematics, seismotectonics and seismic potential of the eastern sector of the European Alps from GPS and seismic deformation data

NASA Astrophysics Data System (ADS)

Serpelloni, E.; Vannucci, G.; Anderlini, L.; Bennett, R. A.

2016-10-01

We present a first synoptic view of the seismotectonics and kinematics of the eastern sector of the European Alps using geodetic and seismological data. The study area marks the boundary between the Adriatic and the Eurasian plates, through a wide zone of deformation including a variety of tectonic styles within a complex network of crustal and lithospheric faults. A new dense GPS velocity field, new focal mechanisms and seismic catalogues, with uniformly re-calibrated magnitudes (from 1005), are used to estimate geodetic and seismic deformation rates and to develop interseismic kinematic and fault locking models. Kinematic indicators from seismological and geodetic data are remarkably consistent at different spatial scales. In addition to large-scale surface motion, GPS velocities highlight more localized deformation features revealing a complex configuration of interacting tectonic blocks, for which new constraints are provided in this work accounting for elastic strain build up at faults bonding rotating blocks. The geodetic and seismological data highlight two belts of higher deformation rates running WSW-ENE along the Eastern Southern Alps (ESA) in Italy and E-W in Slovenia, where deformation is more distributed. The highest geodetic strain-rates are observed in the Montello-Cansiglio segment of the ESA thrust front, for which the higher density of the GPS network provides indications of limited interseismic locking. Most of the dextral shear between the Eastern Southern Alps and the Eastern Alps blocks is accommodated along the Fella-Sava fault rather than the Periadriatic fault. In northern Croatia and Slovenia geodetic and seismological data allow constraining the kinematics of the active structures bounding the triangular-shaped region encompassing the Sava folds, which plays a major role in accommodating the transition from Adria- to Pannonian-like motion trends. The analysis of the seismic and geodetic moment rates provides new insights into the seismic potential along the ESA front.

Geodetic point positioning with GPS (Global Positioning System) carrier beat phase data from the CASA (Central and South America) Uno experiment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Malys, S.; Jensen, P.A.

1990-04-01

The Global Positioning System (GPS) carrier beat phase data collected by the TI4100 GPS receiver has been successfully utilized by the US Defense Mapping Agency in an algorithm which is designed to estimate individual absolute geodetic point positions from data collected over a few hours. The algorithm uses differenced data from one station and two to four GPS satellites at a series of epochs separated by 30 second intervals. The precise GPS ephemerides and satellite clock states, held fixed in the estimation process, are those estimated by the Naval Surface Warfare Center (NSWC). Broadcast ephemerides and clock states are alsomore » utilized for comparative purposes. An outline of the data corrections applied, the mathematical model and the estimation algorithm are presented. Point positioning results and statistics are presented for a globally-distributed set of stations which contributed to the CASA Uno experiment. Statistical assessment of 114 GPS point positions at 11 CASA Uno stations indicates that the overall standard deviation of a point position component, estimated from a few hours of data, is 73 centimeters. Solution of the long line geodetic inverse problem using repeated point positions such as these can potentially offer a new tool for those studying geodynamics on a global scale.« less

Global Positioning System (GPS) survey of Augustine Volcano, Alaska, August 3-8, 2000: data processing, geodetic coordinates and comparison with prior geodetic surveys

USGS Publications Warehouse

Pauk, Benjamin A.; Power, John A.; Lisowski, Mike; Dzurisin, Daniel; Iwatsubo, Eugene Y.; Melbourne, Tim

2001-01-01

Between August 3 and 8,2000,the Alaska Volcano Observatory completed a Global Positioning System (GPS) survey at Augustine Volcano, Alaska. Augustine is a frequently active calcalkaline volcano located in the lower portion of Cook Inlet (fig. 1), with reported eruptions in 1812, 1882, 1909?, 1935, 1964, 1976, and 1986 (Miller et al., 1998). Geodetic measurements using electronic and optical surveying techniques (EDM and theodolite) were begun at Augustine Volcano in 1986. In 1988 and 1989, an island-wide trilateration network comprising 19 benchmarks was completed and measured in its entirety (Power and Iwatsubo, 1998). Partial GPS surveys of the Augustine Island geodetic network were completed in 1992 and 1995; however, neither of these surveys included all marks on the island.Additional GPS measurements of benchmarks A5 and A15 (fig. 2) were made during the summers of 1992, 1993, 1994, and 1996. The goals of the 2000 GPS survey were to:1) re-measure all existing benchmarks on Augustine Island using a homogeneous set of GPS equipment operated in a consistent manner, 2) add measurements at benchmarks on the western shore of Cook Inlet at distances of 15 to 25 km, 3) add measurements at an existing benchmark (BURR) on Augustine Island that was not previously surveyed, and 4) add additional marks in areas of the island thought to be actively deforming. The entire survey resulted in collection of GPS data at a total of 24 sites (fig. 1 and 2). In this report we describe the methods of GPS data collection and processing used at Augustine during the 2000 survey. We use this data to calculate coordinates and elevations for all 24 sites surveyed. Data from the 2000 survey is then compared toelectronic and optical measurements made in 1988 and 1989. This report also contains a general description of all marks surveyed in 2000 and photographs of all new marks established during the 2000 survey (Appendix A).

A catalog of coseismic uniform-slip models of geodetically unstudied earthquakes along the Sumatran plate boundary

NASA Astrophysics Data System (ADS)

Wong, N. Z.; Feng, L.; Hill, E.

2017-12-01

The Sumatran plate boundary has experienced five Mw > 8 great earthquakes, a handful of Mw 7-8 earthquakes and numerous small to moderate events since the 2004 Mw 9.2 Sumatra-Andaman earthquake. The geodetic studies of these moderate earthquakes have mostly been passed over in favour of larger events. We therefore in this study present a catalog of coseismic uniform-slip models of one Mw 7.2 earthquake and 17 Mw 5.9-6.9 events that have mostly gone geodetically unstudied. These events occurred close to various continuous stations within the Sumatran GPS Array (SuGAr), allowing the network to record their surface deformation. However, due to their relatively small magnitudes, most of these moderate earthquakes were recorded by only 1-4 GPS stations. With the limited observations per event, we first constrain most of the model parameters (e.g. location, slip, patch size, strike, dip, rake) using various external sources (e.g., the ANSS catalog, gCMT, Slab1.0, and empirical relationships). We then use grid-search forward models to explore a range of some of these parameters (geographic position for all events and additionally depth for some events). Our results indicate the gCMT centroid locations in the Sumatran subduction zone might be biased towards the west for smaller events, while ANSS epicentres might be biased towards the east. The more accurate locations of these events are potentially useful in understanding the nature of various structures along the megathrust, particularly the persistent rupture barriers.

A comprehensive approach to monitoring volcano deformation as a window on the eruption cycle

USGS Publications Warehouse

Dzurisin, D.

2003-01-01

Since the 1980 eruption of Mount St. Helens, volcanologists have made considerable progress toward predicting eruptions on the basis of precursors that typically start a few days to several months in advance. Although accurate eruption prediction is by no means routine, it may now be possible in some cases to extend the effective warning period by anticipating the onset of short-term precursors. Three promising indicators of deep magmatic processes are (1) deep, long-period earthquakes and tremor that indicate the ascent of magma through the crust, (2) magmatic CO2 emission rate as a proxy for magma supply rate, and (3) relatively broad, generally aseismic surface uplift caused by magmatic intrusions. In the latter case it is essential to sample the deformation field thoroughly in both time and space to adequately constrain source models. Until recently, this has been nearly impossible because high-precision sensors could not be deployed in sufficient numbers, nor could extensive geodetic surveys be conducted often enough. Advances in instrumentation, interferometric synthetic aperture radar (InSAR), and telecommunications are helping to overcome these limitations. As a result, comprehensive geodetic monitoring of selected volcanoes is now feasible. A combination of InSAR, large-aperture GPS surveys, microgravity surveys, and dense arrays of continuous GPS stations, strain meters, and tiltmeters can reveal both spatial and temporal patterns of ground deformation throughout the eruption cycle. Improved geodetic monitoring of many of the world's volcanoes would be a major stride toward better understanding of magmatic processes and longer-term eruption forecasts.

Using GPS and leveling data in local precise geoid determination and case study

NASA Astrophysics Data System (ADS)

Erol, B.; Çelik, R. N.; Erol, S.

2003-04-01

As an important result of developments in high technology, satellite based positioning system has become to use in geodesy and surveying professions. These developments made the measurement works more accurate, more practical and more economic. Today, one of the most recent used satellite based positioning system is GPS (Global Positioning System) and it serves to a very wide range of geodetic applications from monitoring earth crustal deformations till building the basis for a GIS (Geographical Information Systems). The most efficient way to utilize GPS measurement system for mentioned aims is having a reliable geodetic infrastructure in working area. Geodetic infrastructure is a extraterrestrial and time system and involved 4D geodetic reference networks. The forth element of mentioned geodetic reference system is time because having an accurate and reliable geodetic infrastructure is needed to up-date according to physical realities of the region. By the help of a well designed geodetic infrastructure accurate and reliable coordinates of a point can be generated economically every time in a global and up-to-date system. Geoid is one of the important parts of a geodetic infrastructure. As it is well known, geoid is the equipotential surface of the Earth's gravity field which best fits, in a least squares sense, global mean sea level and it is reference for physical height systems like orthometric and normal heights. In the most of the applications, vertical position of a point is expressed with orthometric or normal height. Orthometric or normal height is a physical concept and gives vertical position of a point uniquely. On the other hand, vertical position of a point is derived in a geometrical system according to GPS measurements. GPS datum is WGS84 and in this system, an ellipsoidal height of a point is calculated according to WGS84 ellipsoid. So, it is an necessity to transform the ellipsoidal heights to orthometric heights and this procedure is managed with the fundamental mathematical equation; N=h-H. In the equation, "h" is the ellipsoidal height of a point P, "H" is the orthometric height of the same point and "N" is "geoid undulation" value. Normally, "H" orthometric height derived from leveling measurements but these measurements are tiring applications. So, while having a geoid model in the region as the essential part of geodetic infrastructure, number leveling measurements can be reduced from the procedure and by this way time and labor is saved. Geoid determination is modeling of the data in such a way that geoid height can be obtained digital or analog at a point whose horizontal position is known. Geoid models can be developed for local, regional or global regions. Using satellite techniques, especially GPS, in geodetic measurements are increased importance of geoid. Because geoid is a natural tie between high precision geodetic coordinates and coordinates which obtained from satellites. There are several geoid determination methods according to used data and models. GPS/Leveling method, which is also known as geometric method, is one of these methods. This method is appropriate for local precise geoid determination in respectively small areas. In this paper, it is going to be given information about GPS/Leveling geoid determination method and mathematical models, which are used in geoid determination with this method. And Izmir local geoid model will be presented as a case study. Izmir is one of the west metropolitan cities of Turkey and located near Aegean Sea. The topography is extremely rough in the region. There are two different geoid determination studies which were carried out in 1996 and 2001 in Izmir. Both models were accomplished according to GPS/Leveling method. Those two geoid models of Izmir Metropolitan region are investigated in here, the conflict of them were discussed. The relation between distribution of common reference points and differences of geoid undulation values, which are calculated from both models separately, were analyzed and also effects of topography on conflict of both geoid model was investigated. The results of the study and suggestions are going to be given in the paper.

High rate GPS positioning , JASON altimetry and marine gravimetry : monitoring the Antarctic Circumpolar Current (ACC) through the DRAKE campaigns.

NASA Astrophysics Data System (ADS)

Melachroinos, S. A.; Biancale, R.; Menard, Y.; Sarrailh, M.

2008-12-01

The Drake campaign which took place from Jan 14, 2006 - 08 Feb, 2006 has been a very successful mission in collecting a wide range of GPS and marine gravity data all along JASON altimetry ground track n° 104. The same campaign will be repeated in 2009 along 028 and 104 JASON-2 ground track. The Drake Passage (DP) chokepoint is not only well suited geographically, as the Antarctic Circumpolar Current (ACC) is constricted to its narrowest extent of 700 km, but observations and models suggest that dynamical balances are particular effective in this area. Furthermore the space geodesy observations and their products provided from several altimetry missions (currently operating ENVISAT, JASON 1 and 2, GFO, ERS and other plannified for the future such as Altika, SWOT) require the cross comparison with independent geodetic techniques at the DP. The current experiment comprises a kinematic GPS and marine gravimetry Cal/Val geodetic approach and it aims to : validate with respect to altimetry data and surface models such a kinematic high frequency GPS technique for measuring sea state and sea surface height (SSH), compare the GPS SSH profiles with altimetry mean dynamic topography (MDT) and mean sea surface (MSS) models, give recommendations for future "offshore" Cal/Val activities on the ground tracks of altimeter satellites such as JASON-2, GFO, Altika using the GNSS technology etc. The GPS observations are collected from GPS antennas installed on a wave-rider buoy , aboard the R/V "Polarstern" and from continuous geodetic reference stations in the proximity. We also analyse problems related to the ship's attitude variations in roll, pitch and yaw and a way to correct them. We also give emphasis on the impact of the ship's acceleration profiles on the so called "squat effect" and ways to deal with it. The project will in particular benefit the GOCE mission by proposing to integrate GOCE in the ocean circulation study and validate GOCE products with our independent geodetic data set. The high rate GPS SSH solutions are derived using two different GPS kinematic software, GINS (CNES) and TRACK (MIT).

Investigation of a L1-optimized choke ring ground plane for a low-cost GPS receiver-system

NASA Astrophysics Data System (ADS)

Zhang, Li; Schwieger, Volker

2018-01-01

Besides the geodetic dual-frequency GNSS receivers-systems (receiver and antenna), there are also low-cost single-frequency GPS receiver-systems. The multipath effect is a limiting factor of accuracy for both geodetic dual-frequency and low-cost single-frequency GPS receivers. And the multipath effect is for the short baselines dominating error (typical for the monitoring in Engineering Geodesy). So accuracy and reliability of GPS measurement for monitoring can be improved by reducing the multipath signal. In this paper, the self-constructed L1-optimized choke ring ground plane (CR-GP) is applied to reduce the multipath signal. Its design will be described and its performance will be investigated. The results show that the introduced low-cost single-frequency GPS receiver-system, which contains the Ublox LEA-6T single-frequency GPS receiver and Trimble Bullet III antenna with a self-constructed L1-optimized CR-GP, can reach standard deviations of 3 mm in east, 5 mm in north and 9 mm in height in the test field which has many reflectors. This accuracy is comparable with the geodetic dual-frequency GNSS receiver-system. The improvement of the standard deviation of the measurement using the CR-GP is about 50 % and 35 % compared to the used antenna without shielding and with flat ground plane respectively.

Evaluation of the Horizontal and Vertical Accuracy of GNSS Survey Observations from a Real-Time Network

NASA Astrophysics Data System (ADS)

Allahyari, M.; Olsen, M. J.; Gillins, D. T.; Dennis, M. L.

2016-12-01

Many current surveying standards in the United States require several long-duration, static Global Navigation Satellite System (GNSS) observations to derive high-accuracy geodetic coordinates. However, over the past decade, many entities have established real-time GNSS networks (RTNs), which could reduce the field time for establishing geodetic control from hours to minutes. To evaluate the accuracy of RTN GNSS observations, data collected from two National Geodetic Survey (NGS) surveys in South Carolina and Oregon were studied. The objectives were to: 1) determine the accuracy of a real-time observation as a function of duration; 2) examine the influence of including GLONASS (Russia's version of GPS); 3) compare results using a single base to the full RTN network solution; and 4) assess the effect of baseline length on accuracy. In South Carolina, 360 observations ranging from 5 to 600 seconds were collected on 20 passive marks using RTN and single-base solutions, both with GPS+GLONASS and GPS-only. In Oregon, 18 passive marks were observed from 5 to 900 seconds using GPS-only with the RTN, and with GPS+GLONASS and GPS-only from a single-base. To develop "truth" coordinates, at least 30 hours of static GPS data were also collected on all marks. Each static survey session was post-processed in OPUS-Projects, and the resulting vectors were used to build survey networks that were least-squares adjusted using the NGS software ADJUST. The resulting coordinates provided the basis for evaluating the accuracy of the real-time observations. Results from this study indicate great potential in the use of RTNs for accurate derivation of geodetic coordinates. Both case studies showed an optimal observation duration of 180 seconds. RTN data tended to be more accurate and consistent than single-base data, and GLONASS slightly improved accuracy. A key benefit of GLONASS was the ability to obtain more fixed solutions at longer baseline lengths than single-base solutions.

Long-term mass variations from SLR, VLBI and GPS data

NASA Astrophysics Data System (ADS)

Luceri, Vincenza; Sciarretta, Cecilia; Bianco, Giuseppe

2013-04-01

The second-degree geopotential coefficients reflect the behaviour of the Earth's inertia tensor of order 2 which describes the main mass variations of our planet impacting polar motion and length of day (EOP). SLR, VLBI and GPS allow the estimation of those variations, either directly in the case of SLR through its dynamics, and indirectly, for all the three geodetic techniques, by deriving excitation functions from the EOP estimations. The geodetic estimates include the influence of the Earth's atmosphere and oceans, both from their mass and motion components, which can be modelled using the atmospheric and oceanic angular momenta variations. The different C21, S21 and C20 geodetic time series are compared in order to evaluate their coherence and their response to the mass variations after the removal of the motion terms. Moreover, the residual signal contents of the geodetic values, deprived by the atmospheric and oceanic mass and motion components, will be investigated.

Development of a System to Generate Near Real Time Tropospheric Delay and Precipitable Water Vapor in situ at Geodetic GPS Stations, to Improve Forecasting of Severe Weather Events

NASA Astrophysics Data System (ADS)

Moore, A. W.; Bock, Y.; Geng, J.; Gutman, S. I.; Laber, J. L.; Morris, T.; Offield, D. G.; Small, I.; Squibb, M. B.

2012-12-01

We describe a system under development for generating ultra-low latency tropospheric delay and precipitable water vapor (PWV) estimates in situ at a prototype network of geodetic GPS sites in southern California, and demonstrating their utility in forecasting severe storms commonly associated with flooding and debris flow events along the west coast of North America through infusion of this meteorological data at NOAA National Weather Service (NWS) Forecast Offices and the NOAA Earth System Research Laboratory (ESRL). The first continuous geodetic GPS network was established in southern California in the early 1990s and much of it was converted to real-time (latency <1s) high-rate (1Hz) mode over the following decades. GPS stations are multi-purpose and can also provide estimates of tropospheric zenith delays, which can be converted into mm-accuracy PWV using collocated pressure and temperature measurements, the basis for GPS meteorology (Bevis et al. 1992, 1994; Duan et al. 1996) as implemented by NOAA with a nationwide distribution of about 300 GPS-Met stations providing PW estimates at subhourly resolution currently used in operational weather forecasting in the U.S. We improve upon the current paradigm of transmitting large quantities of raw data back to a central facility for processing into higher-order products. By operating semi-autonomously, each station will provide low-latency, high-fidelity and compact data products within the constraints of the narrow communications bandwidth that often occurs in the aftermath of natural disasters. The onsite ambiguity-resolved precise point positioning solutions are enabled by a power-efficient, low-cost, plug-in Geodetic Module for fusion of data from in situ sensors including GPS and a low-cost MEMS meteorological sensor package. The decreased latency (~5 minutes) PW estimates will provide the detailed knowledge of the distribution and magnitude of PW that NWS forecasters require to monitor and predict severe winter storms, landfalling atmospheric rivers, and summer thunderstorms associated with the North American monsoon. On the national level, the ESRL will evaluate the utility of ultra-low resolution GNSS observations to improve NOAA's warning and forecast capabilities. The overall objective is to better forecast, assess, and mitigate natural hazards through the flow of information from multiple geodetic stations to scientists, mission planners, decision makers, and first responders.

The International GPS Service (IGS) as a Continuous Reference System for Precise GPS Positioning

NASA Technical Reports Server (NTRS)

Neilan, Ruth; Heflin, Michael; Watkins, Michael; Zumberge, James

1996-01-01

The International GPS Service for Geodynamics (IGS) is an organization which operates under the auspices of the International Association of Geodesy (IAG) and has been operational since January 1994. The primary objective of the IGS is to provide precise GPS data and data products to support geodetic and geophysical research activities.

A 10-Year Comparison of Water Levels Measured with a Geodetic GPS Receiver Versus a Conventional Tide Gauge

NASA Technical Reports Server (NTRS)

Larson, Kristine M.; Ray, Richard D.; Williams, Simon D. P.

2017-01-01

A standard geodetic GPS receiver and a conventional Aquatrak tide gauge, collocated at Friday Harbor, Washington, are used to assess the quality of 10 years of water levels estimated from GPS sea surface reflections.The GPS results are improved by accounting for (tidal) motion of the reflecting sea surface and for signal propagation delay by the troposphere. The RMS error of individual GPS water level estimates is about 12 cm. Lower water levels are measured slightly more accurately than higher water levels. Forming daily mean sea levels reduces the RMS difference with the tide gauge data to approximately 2 cm. For monthly means, the RMS difference is 1.3 cm. The GPS elevations, of course, can be automatically placed into a well-defined terrestrial reference frame. Ocean tide coefficients, determined from both the GPS and tide gauge data, are in good agreement, with absolute differences below 1 cm for all constituents save K1 and S1. The latter constituent is especially anomalous, probably owing to daily temperature-induced errors in the Aquatrak tide gauge

Time and position accuracy using codeless GPS

NASA Technical Reports Server (NTRS)

Dunn, C. E.; Jefferson, D. C.; Lichten, S. M.; Thomas, J. B.; Vigue, Y.; Young, L. E.

1994-01-01

The Global Positioning System has allowed scientists and engineers to make measurements having accuracy far beyond the original 15 meter goal of the system. Using global networks of P-Code capable receivers and extensive post-processing, geodesists have achieved baseline precision of a few parts per billion, and clock offsets have been measured at the nanosecond level over intercontinental distances. A cloud hangs over this picture, however. The Department of Defense plans to encrypt the P-Code (called Anti-Spoofing, or AS) in the fall of 1993. After this event, geodetic and time measurements will have to be made using codeless GPS receivers. However, there appears to be a silver lining to the cloud. In response to the anticipated encryption of the P-Code, the geodetic and GPS receiver community has developed some remarkably effective means of coping with AS without classified information. We will discuss various codeless techniques currently available and the data noise resulting from each. We will review some geodetic results obtained using only codeless data, and discuss the implications for time measurements. Finally, we will present the status of GPS research at JPL in relation to codeless clock measurements.

Assessment of 3D hydrologic deformation using GRACE and GPS

NASA Astrophysics Data System (ADS)

Watson, C. S.; Tregoning, P.; Fleming, K.; Burgette, R. J.; Featherstone, W. E.; Awange, J.; Kuhn, M.; Ramillien, G.

2009-12-01

Hydrological processes cause variations in gravitational potential and surface deformations, both of which are detectable with ever increasing precision using space geodetic techniques. By comparing the elastic deformation computed from continental water load estimates derived from the Gravity Recovery and Climate Experiment (GRACE), with three-dimensional surface deformation derived from GPS observations, there is clear potential to better understand global to regional hydrological processes, in addition to acquiring further insight into the systematic error contributions affecting each space geodetic technique. In this study, we compare elastic deformation derived from water load estimates taken from the CNES, CSR, GFZ and JPL time variable GRACE fields. We compare these surface displacements with those derived at a global network of GPS sites that have been homogeneously reprocessed in the GAMIT/GLOBK suite. We extend our comparison to include a series of different GPS solutions, with each solution only subtly different based on the methodology used to down weight the height component in realizing site coordinates on the terrestrial reference frame. Each of the GPS solutions incorporate modeling of atmospheric loading and utilization of the VMF1 and a priori zenith hydrostatic delays derived via ray tracing through ECMWF meteorological fields. The agreement between GRACE and GPS derived deformations is not limited to the vertical component, with excellent agreement in the horizontal component across areas where large hydrologic signals occur over broad spatial scales (with correlation in horizontal components as high as 0.9). Agreement is also observed at smaller scales, including across Europe. These comparisons assist in understanding the magnitude of current error contributions within both space geodetic techniques. With the emergence of homogeneously reprocessed GPS time series spanning the GRACE mission, this technique offers one possible means of validating the amplitude and phase of quasi-periodic signals present in GPS time series.

Reprocessing Multiyear GPS Data from Continuously Operating Reference Stations on Cloud Computing Platform

NASA Astrophysics Data System (ADS)

Yoon, S.

2016-12-01

To define geodetic reference frame using GPS data collected by Continuously Operating Reference Stations (CORS) network, historical GPS data needs to be reprocessed regularly. Reprocessing GPS data collected by upto 2000 CORS sites for the last two decades requires a lot of computational resource. At National Geodetic Survey (NGS), there has been one completed reprocessing in 2011, and currently, the second reprocessing is undergoing. For the first reprocessing effort, in-house computing resource was utilized. In the current second reprocessing effort, outsourced cloud computing platform is being utilized. In this presentation, the outline of data processing strategy at NGS is described as well as the effort to parallelize the data processing procedure in order to maximize the benefit of the cloud computing. The time and cost savings realized by utilizing cloud computing approach will also be discussed.

Geodynamical behavior of some active area in Egypt, as deduced from geodetic and gravity data

NASA Astrophysics Data System (ADS)

Issawy, E.; Mrlina, J.; Radwan, A.; Mahmoud, S.; Rayan, A.

2009-04-01

Temporal gravity variation in parallel with the space geodetic technique (GPS) had been started in Egypt for real campaigns in 1997. The geodetic networks around the High Dam, Aswan area was the first net to be measured. More than five measurement epochs were performed. The results had a considerable limit of coincidence between gravity and GPS observations. The trend of gravity changes indicated a positive stress and had the vertical displacement observed for leveling points. The lowest gravity changes along Kalabsha fault reflect extensional and/or strike component of the stress field. Also, the areas around Cairo (Greater Cairo) and due to the occurrence of an earthquake of 1992, such type of measurements were useful for monitoring the recent activity. The data of the geodetic network around Cairo after 5 campaigns showed that, the estimated horizontal velocities for almost all points are 5.5± mm/year in approximately NW-SE direction. The non-tidal changes can explain the dynamic process within the upper crust related to the development of local stress conditions. The trends of gravity changes are more or less coincident with that deduced from GPS deformation analysis and the occurrence of the main shocks in the area. In additions, in 2005 the geodetic network around the southern part of Sinai and the Gulf of Suez were established. One campaign of measurements had been performed and the gravity values were obtained.

The Contribution of the IGS to a Globally Integrated Geodetic Observing System

NASA Astrophysics Data System (ADS)

WEBER, R.

2002-05-01

The dedicated goal of the International GPS Service (IGS) is 'to provide a service to support geodetic and geophysical research activities through GPS data and data products'. To accomplish its mission IGS began routine operations in Jan 1994. Nowadays operations are based on a large number of components like a globally distributed tracking network of about 200 stations, local and regional data centers as well as eight analysis centers. This presentation summarizes the measurement principles of the GPS and GLONASS microwave satellite navigation systems. An overview of current IGS-products will be given and factors limiting the accuracy of these products are discussed. Moreover IGS serves as one of the technique center of the IERS and therefore the delivered products follow designated IERS standards as close as possible. It can be anticipated that the IGS will also play an important role within the framework of an upcoming Globally Integrated Geodetic Observing System. Even today there are a number of scientific crosslinks to other space geodetic techniques and services e.g. to the ILRS in the determination of the geocentre or to the IVS in questions of a temporal and spatial densification of the reference frame. The above-mentioned initiative will strengthen further the cooperation and increase the scientific outcome.

How well can online GPS PPP post-processing services be used to establish geodetic survey control networks?

NASA Astrophysics Data System (ADS)

Ebner, R.; Featherstone, W. E.

2008-09-01

Establishing geodetic control networks for subsequent surveys can be a costly business, even when using GPS. Multiple stations should be occupied simultaneously and post-processed with scientific software. However, the free availability of online GPS precise point positioning (PPP) post-processing services offer the opportunity to establish a whole geodetic control network with just one dual-frequency receiver and one field crew. To test this idea, we compared coordinates from a moderate-sized (~550 km by ~440 km) geodetic network of 46 points over part of south-western Western Australia, which were processed both with the Bernese v5 scientific software and with the CSRS (Canadian Spatial Reference System) PPP free online service. After rejection of five stations where the antenna type was not recognised by CSRS, the PPP solutions agreed on average with the Bernese solutions to 3.3 mm in east, 4.8 mm in north and 11.8 mm in height. The average standard deviations of the Bernese solutions were 1.0 mm in east, 1.2 mm in north and 6.2 mm in height, whereas for CSRS they were 3.9 mm in east, 1.9 mm in north and 7.8 mm in height, reflecting the inherently lower precision of PPP. However, at the 99% confidence level, only one CSRS solution was statistically different to the Bernese solution in the north component, due to a data interruption at that site. Nevertheless, PPP can still be used to establish geodetic survey control, albeit with a slightly lower quality because of the larger standard deviations. This approach may be of particular benefit in developing countries or remote regions, where geodetic infrastructure is sparse and would not normally be established without this approach.

Integration of space geodesy: A US National Geodetic Observatory

NASA Astrophysics Data System (ADS)

Yunck, Thomas P.; Neilan, Ruth E.

2005-11-01

In the interest of improving the performance and efficiency of space geodesy a diverse group in the US, in collaboration with IGGOS, has begun to establish a unified National Geodetic Observatory (NGO). To launch this effort an international team will conduct a multi-year program of research into the technical issues of integrating SLR, VLBI, and GPS geodesy to produce a unified set of global geodetic products. The goal is to improve measurement accuracy by up to an order of magnitude while lowering the cost to current sponsors. A secondary goal is to expand and diversify international sponsorship of space geodesy. Principal benefits will be to open new vistas of research in geodynamics and surface change while freeing scarce NASA funds for scientific studies. NGO will proceed in partnership with, and under the auspices of, the International Association of Geodesy (IAG) as an element of the Integrated Global Geodetic Observation System project. The collaboration will be conducted within, and will make full use of, the IAG's existing international services: the IGS, IVS, ILRS, and IERS. Seed funding for organizational activities and technical analysis will come from NASA's Solid Earth and Natural Hazards Program. Additional funds to develop an integrated geodetic data system known as Inter-service Data Integration for Geodetic Operations (INDIGO), will come from a separate NASA program in Earth science information technology. INDIGO will offer ready access to the full variety of NASA's space geodetic data and will extend the GPS Seamless Archive (GSAC) philosophy to all space geodetic data types.

Integrating Continuous GPS Time Series and Geodetic Leveling Data to Estimate Secular Vertical Velocity of Taiwan

NASA Astrophysics Data System (ADS)

LAI, Y. R.; Hsu, Y. J.; You, R. J.

2017-12-01

GPS technique services as the most powerful method in monitoring crustal deformation owing to its advantage of temporal continuity. Geodetic leveling is also widely used not only in engineering but also in geophysics applicants due to its high precision in vertical datum determination and spatial continuity advantages. As widely known, the reference frames of GPS and geodetic leveling are different- the former refers to the reference ellipsoid (WGS84 ellipsoid) and the latter refers to the geoid. In order to combine vertical velocity fields from different datums, we decide to examine discrepancy between these two data sets. Moreover, GPS stations and benchmarks always do not locate at the same places. In place of using a spatial reduced function (Ching et.al, JGR, 2011) to find the discrepancy between them, we focused on comparing termporal variation of GPS vertical motions and geodetic leveling displacements. In this study, we analyzed the vertical velocity field from 238 GPS stations and 1634 benchmarks, including the time-period (2000 to 2015) influenced by postseismiceffects from 1999 Chi-Chi earthquake (Mw 7.6), 2003 Chengkung earthquake (Mw 6.8), and so on. After we thoroughly examined all the process and considered coseismic and postseismic deformation of significant earthquakes, we found that the discrepancy of vertical velocity of the GPS station and its nearby benchmarks is about 1 - 2 mm/yr, including several source of errors in data processing. We suggest that this discrepancy of vertical velocity field can be ignored as tolerable error, and two heterogeneous fields can be integrated together without any mathematical presumptions of spatial regression. The result shows that the western coast is suffering sever subsidence with rates up to 40 mm/yr; the Central Range of Taiwan is uplifting with rates about +10 mm/yr and active landslides with significant subsidence of 5-10 mm/yr in local area. A huge velocity contrast of 30 mm;/yr indicating east over west thrusting is shown across the Longitudinal Valley Fault. Estimation of vertical velocity from 2000 to 2015 is consistent with velocities from 2008 to 2015, indicating our modification process is not affected by the Chi-Chi earthquake (Mw 7.6).

Aseismic Deformation Associated with an Earthquake Swarm in the Northern Apennines (Italy)

NASA Astrophysics Data System (ADS)

Gualandi, A.; Nichele, C.; Serpelloni, E.; Chiaraluce, L.; Anderlini, L.; Latorre, D.; Belardinelli, M. E.; Avouac, J. P.

2017-12-01

Analyzing the displacement time series from continuous GPS (cGPS) with an Independent Component Analysis (ICA) we detect a transient deformation signal that correlates both in space and time with a seismic swarm activity (maximum Mw = 3.69 ± 0.09) occurred in the hanging wall of the Altotiberina normal fault (Northern Apennines, Italy) in 2013-2014. The geodetic transient lasted ˜6 months and produced a NW-SE trending extension of ˜ 5.3 mm, consistent with the regional tectonic regime. The seismicity and the geodetic signal are consistent with slip on two splay faults in the ATF hanging wall. Comparing the seismic moment associated with the geodetic transient and the seismic events, we observe that seismicity accounts for only a fraction of the measured geodetic deformation. The combined seismic and aseismic slip decreased the Coulomb stress on the locked shallow portion of the ATF, while the transition region to the creeping section has been loaded.

GPS/Acoustic seafloor observation in eastern Taiwan

NASA Astrophysics Data System (ADS)

Chen, H. Y.; Ando, M.; Lin, C. H.

2017-12-01

Two sets of transponder arrays, around 100 km off-Ilan and off-Hualien, respectively, have been establisted to estimate the movement behaviors at the upper part of the subduction zone between the Philippine sea plate and Ryukyu islands arc collision boundary in eastern Taiwan since 2012 and 2014. Ten seafloor geodetic surveys have been conducted for off-Ilan array on July 2012, April, July, September 2013, September 2014, July, September 2015, June, August 2016, August 2017, and Four campaigns on September 2015, June, August 2016, August 2017 for off-Hualien array. The positioning results have been acquired on root-mean-square (rms) in 0.06 and 0.10 msec (i.e. 7 and 12 cm) of positioning accuracy. Compare the accuracy with further studies on Peru-Chile trench and Nankai Trough of Japan, the results is slight worse in 2-3 cm level. The primary velocity shows 6.0±1.2 cm to the south 7.1±2.2 cm to the west and 1.7±1.9 downward from July 2012 to August 2017 in the off-Ilan array, and 6.1±11.8 cm to the south 5.2±10.6 cm to the west and 47.0±16.0 downward from September 2015 to August 2017 in the off-Hualien array. The movement behavior of this result is similar to the onshore vectors estimated by GPS, but the uncertainty of the velocity is still slight large to determine the positions precisely. However, the accuracy has been improved by extending the experience time spend and prolonging the observation periods.

Interferometric investigations with the S1 constellation: an application to the Vesuvius/Campi Flegrei volcanic test site

NASA Astrophysics Data System (ADS)

Borgstrom, Sven; Del Gaudio, Carlo; De Martino, Prospero; Siniscalchi, Valeria; Prats-Iraola, Pau; Nannini, Matteo; Yague-Martinez, Nestor; Pinheiro, Muriel; Kim, Jun-Su; Vecchioli, Francesco; Minati, Federico; Costantini, Mario; Foumelis, Michael; Desnos, Yves-Louis

2017-04-01

The contribution focuses on the current status of the ESA study entitled "INSARAP Sentinel-1 Constellation Study" and investigates the interferometric performance of the S1A/S1B units. In particular, we refer to the Vesuvius/Campi Flegrei (Southern Italy) volcanic test site, where the continuous inflation (about 35 cm from 2011 to date) and the huge availability of ground-based geodetic data (continuous GPS - cGPS - leveling, tiltmetric, gravimetric, etc.) from the INGV-Osservatorio Vesuviano monitoring networks have allowed to get a clear deformation signal, besides the comparison between S1A/S1B and geodetic data. In this regard, the integration between InSAR and geodetic measurements is crucial for a continuous and extended monitoring of such an active volcanic area, as InSAR investigations allow to get an information on wide areas, whereas permanent networks (e.g., cGPS), allow to provide a continuous information complementing InSAR, which is limited by its revisiting time. Comparisons between S1 constellation data and geodetic measurements, with a particular focus on cGPS, will be presented, exploiting both LOS and inverted (E-W and vertical inversion) InSAR data starting from October, 2014. In addition, as a next step we are planning to model the deformation source of the area by exploiting the S1 time series results. Ultimately, very encouraging results suggest for a continuation of this activity also for the future, showing the great potential of S1 constellation data for monitoring active volcanic areas and, in general, to retrieve a very high quality deformation signal.

Multi-geodetic characterization of the seasonal signal at the CERGA geodetic reference station, France

NASA Astrophysics Data System (ADS)

Mémin, Anthony; Viswanathan, Vishnu; Fienga, Agnes; Santamarìa-Gómez, Alvaro; Boy, Jean-Paul; Cavalié, Olivier; Deleflie, Florent; Exertier, Pierre; Bernard, Jean-Daniel; Hinderer, Jacques

2017-04-01

Crustal deformations due to surface-mass loading account for a significant part of the variability in geodetic time series. A perfect understanding of the loading signal observed by geodetic techniques should help in improving terrestrial reference frame (TRF) realizations. Yet, discrepancies between crustal motion estimates from models of surface-mass loading and observations are still too large so that no model is currently recommended by the IERS for reducing the observations. We investigate the discrepancy observed in the seasonal variations of the position at the CERGA station, South of France. We characterize the seasonal motions of the reference geodetic station CERGA from GNSS, SLR, LLR and InSAR. We investigate the consistency between the station motions deduced from these geodetic techniques and compare the observed station motion with that estimated using models of surface-mass change. In that regard, we compute atmospheric loading effects using surface pressure fields from ECMWF, assuming an ocean response according to the classical inverted barometer (IB) assumption, considered to be valid for periods typically exceeding a week. We also used general circulation ocean models (ECCO and GLORYS) forced by wind, heat and fresh water fluxes. The continental water storage is described using GLDAS/Noah and MERRA-land models. Using the surface-mass models, we estimate that the seasonal signal due to loading deformation at the CERGA station is about 8-9, 1-2 and 1-2 mm peak-to-peak in Up, North and East component, respectively. There is a very good correlation between GPS observations and non-tidal loading predicted deformation due to atmosphere, ocean and hydrology which is the main driver of seasonal signal at CERGA. Despite large error bars, LLR observations agree reasonably well with GPS and non-tidal loading predictions in Up component. Local deformation as observed by InSAR is very well correlated with GPS observations corrected for non-tidal loading. Finally, we estimate local mass changes using the absolute gravity measurement campaigns available at the station and the global models of surface-mass change. We compute the induced station motion that we compare with the local deformation observed by InSAR and GPS.

Incorporating GPS geodetic data into the undergraduate classroom to improve data and information literacy

NASA Astrophysics Data System (ADS)

Jansma, P. E.; Mattioli, G. S.

2002-12-01

As part of an NSF-funded project, we are incorporating Global Positioning System (GPS) geodesy into the classroom to improve data and information literacy among undergraduate students. Our objectives are: to introduce statistical concepts essential for the interpretation of large datasets; to promote communication skills; to enhance critical thinking; and to build teamwork. GPS geodesy is ideal for illustrating data literacy concepts. Data precision and accuracy depend upon several factors, including type of equipment, environmental conditions, length of occupations, monument design, site location, configuration of the geodetic network, and processing strategies. All of these can be varied, allowing the students to learn the trade-offs among cost, time, and quality and to determine the most efficient methodology for specific problems. In addition, precision, accuracy, and errors govern the interpretations that can be made and the potential to distinguish among competing models. Our focus is a semester-long course that uses GPS geodesy in real-world applications and also requires integration of GPS data into oral presentations and written reports. Students work in teams on "cases" that pose hypotheses for testing. The cases are derived from our on-going research projects and take advantage of on-line continuous GPS (CGPS) data as well as our archived campaign data. The case studies are: 1) Microplate tectonics in the northeastern Caribbean; 2) Inflation/deflation cycles of the Soufriere Hills volcano, Montserrat; and 3) Contribution of monument instability to the overall error in geodetic data from the New Madrid Seismic Zone. All course materials will be on-line and available for the community.

A global positioning measurement system for regional geodesy in the caribbean

NASA Astrophysics Data System (ADS)

Renzetti, N. A.

1986-11-01

Low cost, portable receivers using signals from satellites of the Global Positioning System (GPS) will enable precision geodetic observations to be made on a large scale. A number of important geophysical questions relating to plate-motion kinematics and dynamics can be addressed with this measurement capability. We describe a plan to design and validate a GPS-based geodetic system, and to demonstrate its capability in California, Mexico and the Caribbean region. The Caribbean program is a prototype for a number of regional geodetic networks to be globally distributed. In 1985, efforts will be concentrated on understanding and minimizing error sources. Two dominant sources of error are uncertainties in the orbit ephemeris of the GPS satellites, and uncertainties in the correction for signal delay due to variable tropospheric water vapor. Orbit ephemeris uncertainties can be minimized by performing simultaneous satellite observations with GPS receivers at known (fiducial) points. Water vapor corrections can be made by performing simultaneous line-of-sight measurements of integrated water vapor content with ground-based water vapor radiometers. Specific experiments to validate both concepts are outlined. Caribbean measurements will begin in late 1985 or early 1986. Key areas of measurement are the northern strike-slip boundary, and the western convergent boundary. Specific measurement plans in both regions are described.

Hiking and biking with GPS: The Canadian perspective

NASA Astrophysics Data System (ADS)

Vaníček, Petr

The paper attempts to review and put into perspective the findings of a recent by-invitation-only workshop on GPS held in Ottawa. The workshop brought together both GPS-information suppliers and consumers coming from all walks of life. Some unique exchanges of views took place which are worth bringing to the attention of the geodetic community.

TLALOCNet: A Continuous GPS-Met Array in Mexico for Seismotectonic and Atmospheric Research

NASA Astrophysics Data System (ADS)

Cabral-Cano, E.; Salazar-Tlaczani, L.; Galetzka, J.; DeMets, C.; Serra, Y. L.; Feaux, K.; Mattioli, G. S.; Miller, M. M.

2015-12-01

TLALOCNet is a network of continuous Global Positioning System (cGPS) and meteorology stations in Mexico for the interrogation of the earthquake cycle, tectonic processes, land subsidence, and atmospheric processes of Mexico. Once completed, TLALOCNet will span all of Mexico and will link existing GPS infrastructure in North America and the Caribbean aiming towards creating a continuous, federated network of networks in the Americas. Phase 1 (2014-2015), funded by NSF and UNAM, is building and upgrading 30+ cGPS-Met sites to the high standard of the EarthScope Plate Boundary Observatory (PBO). Phase 2 (2016) will add ~25 more cGPS-Met stations to be funded through CONACyT. TLALOCNet provides open and freely available raw GPS data, GPS-PWV, surface meteorology measurements, time series of daily positions, as well as a station velocity field to support a broad range of geoscience investigations. This is accomplished through the development of the TLALOCNet data center (http://tlalocnet.udg.mx) that serves as a collection and distribution point. This data center is based on UNAVCO's Dataworks-GSAC software and can work as part of UNAVCO's seamless archive for discovery, sharing, and access to data.The TLALOCNet data center also contains contributed data from several regional networks in Mexico. By using the same protocols and structure as the UNAVCO and other COCONet regional data centers, the geodetic community has the capability of accessing data from a large number of scientific and academically operated Mexican GPS sites. This archive provides a fully querable and scriptable GPS and Meteorological data retrieval point. Additionally Real-time 1Hz streams from selected TLALOCNet stations are available in BINEX, RTCM 2.3 and RTCM 3.1 formats via the Networked Transport of RTCM via Internet Protocol (NTRIP).

Orbiter global positioning system design and Ku-band problem investigations, exhibit B, revision 1

NASA Technical Reports Server (NTRS)

Lindsey, W. C.

1983-01-01

The hardware, software, and interface between them was investigated for a low dynamics, nonhostile environment, low cost GPS receiver (GPS Z set). The set is basically a three dimensional geodetic and way point navigator with GPS time, ground speed, and ground track as possible outputs in addition to the usual GPS receiver set outputs. Each functional module comprising the GPS set is described, enumerating its functional inputs and outputs, leading to the interface between hardware and software of the set.

Working with strainmeter data

USGS Publications Warehouse

Hodgkinson, Kathleen M.; Agnew, Duncan; Roeloffs, Evelyn A.

2013-01-01

The Plate Boundary Observatory (PBO), the geodetic component of the U.S. National Science Foundation–funded Earthscope program, includes 75 borehole and 6 laser strainmeters (http://pbo.unavco.org). The strainmeters are installed at several locations: on the Cascadia forearc in Washington state and on Vancouver Island, Canada; in arrays of two to nine instruments along the North American–Pacific plate boundary in California; at Mount St. Helens; and in Yellowstone National Park. For deformation signals seconds to weeks in duration, strainmeters have a resolution and a signal-to-noise ratio superior to those of seismometers and GPS. However, this high sensitivity can introduce nontectonic signals into strain data, presenting data interpretation challenges, especially for borehole strainmeters.

Slow Earthquake Hunters: A New Citizen Science Project to Identify and Catalog Slow Slip Events in Geodetic Data

NASA Astrophysics Data System (ADS)

Bartlow, N. M.

2017-12-01

Slow Earthquake Hunters is a new citizen science project to detect, catalog, and monitor slow slip events. Slow slip events, also called "slow earthquakes", occur when faults slip too slowly to generate significant seismic radiation. They typically take between a few days and over a year to occur, and are most often found on subduction zone plate interfaces. While not dangerous in and of themselves, recent evidence suggests that monitoring slow slip events is important for earthquake hazards, as slow slip events have been known to trigger damaging "regular" earthquakes. Slow slip events, because they do not radiate seismically, are detected with a variety of methods, most commonly continuous geodetic Global Positioning System (GPS) stations. There is now a wealth of GPS data in some regions that experience slow slip events, but a reliable automated method to detect them in GPS data remains elusive. This project aims to recruit human users to view GPS time series data, with some post-processing to highlight slow slip signals, and flag slow slip events for further analysis by the scientific team. Slow Earthquake Hunters will begin with data from the Cascadia subduction zone, where geodetically detectable slow slip events with a duration of at least a few days recur at regular intervals. The project will then expand to other areas with slow slip events or other transient geodetic signals, including other subduction zones, and areas with strike-slip faults. This project has not yet rolled out to the public, and is in a beta testing phase. This presentation will show results from an initial pilot group of student participants at the University of Missouri, and solicit feedback for the future of Slow Earthquake Hunters.

The Stability of GPS Carrier-Phase Receivers

DTIC Science & Technology

2010-11-01

Frequency Transfer ( TWSTFT ) method [2]. For both CP and TWSTFT , accuracy in time transfer is achieved through special calibration efforts that retain...View (CV) receivers and TWSTFT equipment. Many of these geodetic receivers operate continuously within the International GNSS Service (IGS), and...with TWSTFT , GPS CV, and GPS P3. If ionosphere-free measurements are used in combination with nominally compensated tropospheric corrections, a

Coseismic slip distributions of the 26 December 2004 Sumatra-Andaman and 28 March 2005 Nias earthquakes from GPS static offsets

USGS Publications Warehouse

Banerjee, P.; Pollitz, F.; Nagarajan, B.; Burgmann, R.

2007-01-01

Static offsets produced by the 26 December 2004 M ???9 Sumatra-Andaman earthquake as measured by Global Positioning System (GPS) reveal a large amount of slip along the entire ???1300 km-long rupture. Most seismic slip inversions place little slip on the Andaman segment. whereas both near-field and far-field GPS offsets demand large slip on the Andaman segment. We compile available datasets of the static offset to render a more detailed picture of the static-slip distribution. We construct geodetic offsets such that postearthquake positions of continuous GPS sites are reckoned to a time 1 day after the earthquake and campaign GPS sites are similarly corrected for postseismic motions. The newly revised slip distribution (Mw 9.22) reveals substantial segmentation of slip along the Andaman Islands, with the southern quarter slipping ???15 m in unison with the adjacent Nicobar and northern Sumatran segments of length ???700 km. We infer a small excess of geodetic moment relative to the seismic moment. A similar compilation of GPS offsets from the 28 March 2005 Nias earthquake is well explained with dip slip averaging several meters (Mw = 8.66) distributed primarily at depths greater than 20 km.

A Kalman Filter Implementation for Precision Improvement in Low-Cost GPS Positioning of Tractors

PubMed Central

Gomez-Gil, Jaime; Ruiz-Gonzalez, Ruben; Alonso-Garcia, Sergio; Gomez-Gil, Francisco Javier

2013-01-01

Low-cost GPS receivers provide geodetic positioning information using the NMEA protocol, usually with eight digits for latitude and nine digits for longitude. When these geodetic coordinates are converted into Cartesian coordinates, the positions fit in a quantization grid of some decimeters in size, the dimensions of which vary depending on the point of the terrestrial surface. The aim of this study is to reduce the quantization errors of some low-cost GPS receivers by using a Kalman filter. Kinematic tractor model equations were employed to particularize the filter, which was tuned by applying Monte Carlo techniques to eighteen straight trajectories, to select the covariance matrices that produced the lowest Root Mean Square Error in these trajectories. Filter performance was tested by using straight tractor paths, which were either simulated or real trajectories acquired by a GPS receiver. The results show that the filter can reduce the quantization error in distance by around 43%. Moreover, it reduces the standard deviation of the heading by 75%. Data suggest that the proposed filter can satisfactorily preprocess the low-cost GPS receiver data when used in an assistance guidance GPS system for tractors. It could also be useful to smooth tractor GPS trajectories that are sharpened when the tractor moves over rough terrain. PMID:24217355

Improving deformation models by discounting transient signals in geodetic data: 2. Geodetic data, stress directions, and long-term strain rates in Italy

NASA Astrophysics Data System (ADS)

Carafa, Michele M. C.; Bird, Peter

2016-07-01

The lithosphere of Italy is exposed to a number of different short-term strain transients, including but not limited to landslides, postseismic relaxation, and volcanic inflation/deflation. These transients affect GPS velocities and complicate the assessment of the long-term tectonic component of the surface deformation. In a companion paper we present a method for anticipating the principal patterns of nontectonic, short-term strains and building this information into the covariance matrix of the geodetic velocities. In this work we apply this method to Italian GPS velocities to build an augmented covariance matrix that characterizes all expected discrepancies between short- and long-term velocities. We find that formal uncertainties usually reported for GPS measurements are smaller than the variability of the same benchmarks across a geologic time span. Furthermore, we include in our modeling the azimuths of most compressive horizontal principal stresses (SHmax) because GPS data cannot resolve the active kinematics of coastal and offshore areas. We find that the final tectonic model can be made relatively insensitive to short-term interfering processes if the augmented covariance matrix and SHmax data records are used in the objective function. This results in a preferred neotectonic model that is also in closer agreement with independent geologic and seismological constraints and has the advantage of reducing short-term biases in forecasts of long-term seismicity.

Effect of wet tropospheric path delays on estimation of geodetic baselines in the Gulf of California using the Global Positioning System

NASA Technical Reports Server (NTRS)

Tralli, David M.; Dixon, Timothy H.; Stephens, Scott A.

1988-01-01

Surface Meteorological (SM) and Water Vapor Radiometer (WVR) measurements are used to provide an independent means of calibrating the GPS signal for the wet tropospheric path delay in a study of geodetic baseline measurements in the Gulf of California using GPS in which high tropospheric water vapor content yielded wet path delays in excess of 20 cm at zenith. Residual wet delays at zenith are estimated as constants and as first-order exponentially correlated stochastic processes. Calibration with WVR data is found to yield the best repeatabilities, with improved results possible if combined carrier phase and pseudorange data are used. Although SM measurements can introduce significant errors in baseline solutions if used with a simple atmospheric model and estimation of residual zenith delays as constants, SM calibration and stochastic estimation for residual zenith wet delays may be adequate for precise estimation of GPS baselines. For dry locations, WVRs may not be required to accurately model tropospheric effects on GPS baselines.

Constraining slip distributions and onset of shallow slow slip in New Zealand by joint inversions of onshore and offshore geodetic data.

NASA Astrophysics Data System (ADS)

Yohler, R. M.; Bartlow, N. M.; Wallace, L. M.; Williams, C. A.

2017-12-01

Investigation of slow slip events (SSEs) has become a useful tool for understanding plate boundary fault mechanics in subduction zones where the largest earthquakes occur. An area of specific importance is along the Hikurangi subduction zone in New Zealand, where repeating, known offshore and onshore slow slip patches have been identified since 2002 from the GeoNet cGPS array. Most models of offshore SSEs in New Zealand and elsewhere are solely constrained by these land-based cGPS arrays. This has led to models with poor resolution out near the trench of the subduction zone, where tsunami hazards are greatest. However, a year-long deployment of seafloor pressure sensors (titled "Hikurangi Ocean Bottom Investigation of Tremor and Slow Slip" (HOBITSS)) took place from mid-2014 to mid-2015 offshore of Gisborne, New Zealand and the northern Hikurangi subduction margin. In September 2014, a large SSE was recorded by the HOBITSS and onshore cGPS arrays which allowed for a slip model with better resolution near the trench [Wallace et al., Science, 2016]. Here we investigate the static and time-dependent slip distribution and propagation during the 2014 SSE by joint inversion of the HOBITSS ocean bottom pressure data and onshore cGPS data using the Network Inversion Filter (NIF). This inversion also incorporates more realistic elastic properties by generating Greens functions using the PyLith finite element code with material properties inferred from the New-Zealand wide seismic velocity model. The addition of the APG data and realistic elastic properties not only increased the slip amplitude during the SSE, but also suggests that the onset of the SSE is several days earlier than models predicted by only cGPS. Moreover, the addition of the APG data increased model resolution directly over the SSE by several cm. Additionally, we will also test ranges of possible slip distributions by using the moment bounding technique described in Johnson et al. 1994. While the NIF relies on smoothing parameters for a best fit model, this technique is free from smoothing constraints and will ultimately aid in understanding the range of SSE slip magnitudes that can be fit by the GPS and APG data.

Production and Uses of Multi-Decade Geodetic Earth Science Data Records

NASA Astrophysics Data System (ADS)

Bock, Y.; Kedar, S.; Moore, A. W.; Fang, P.; Liu, Z.; Sullivan, A.; Argus, D. F.; Jiang, S.; Marshall, S. T.

2017-12-01

The Solid Earth Science ESDR System (SESES) project funded under the NASA MEaSUREs program produces and disseminates mature, long-term, calibrated and validated, GNSS based Earth Science Data Records (ESDRs) that encompass multiple diverse areas of interest in Earth Science, such as tectonic motion, transient slip and earthquake dynamics, as well as meteorology, climate, and hydrology. The ESDRs now span twenty-five years for the earliest stations and today are available for thousands of global and regional stations. Using a unified metadata database and a combination of GNSS solutions generated by two independent analysis centers, the project currently produces four long-term ESDR's: Geodetic Displacement Time Series: Daily, combined, cleaned and filtered, GIPSY and GAMIT long-term time series of continuous GPS station positions (global and regional) in the latest version of ITRF, automatically updated weekly. Geodetic Velocities: Weekly updated velocity field + velocity field histories in various reference frames; compendium of all model parameters including earthquake catalog, coseismic offsets, and postseismic model parameters (exponential or logarithmic). Troposphere Delay Time Series: Long-term time series of troposphere delay (30-min resolution) at geodetic stations, necessarily estimated during position time series production and automatically updated weekly. Seismogeodetic records for historic earthquakes: High-rate broadband displacement and seismic velocity time series combining 1 Hz GPS displacements and 100 Hz accelerometer data for select large earthquakes and collocated cGPS and seismic instruments from regional networks. We present several recent notable examples of the ESDR's usage: A transient slip study that uses the combined position time series to unravel "tremor-less" slow tectonic transient events. Fault geometry determination from geodetic slip rates. Changes in water resources across California's physiographic provinces at a spatial resolution of 75 km. Retrospective study of a southern California summer monsoon event.

Evaluation of the Time and Frequency Transfer Capabilities of a Network of GNSS Receivers Located in Timing Laboratories

DTIC Science & Technology

2009-11-01

metrology, different techniques are used for time and frequency transfer, basically TWSTFT (Two-Way Satellite Time and Frequency Transfer), GPS CV (Common...traditional GPS/GLONASS CV/AV receivers and TWSTFT equipment. Time and frequency transfer using GPS code and carrier-phase is an important...or mixing GPS geodetic results with other independent techniques, such as the TWSTFT . 41 st Annual Precise Time and Time Interval (PTTI

Further characterization of the time transfer capabilities of precise point positioning (PPP): the Sliding Batch Procedure.

PubMed

Guyennon, Nicolas; Cerretto, Giancarlo; Tavella, Patrizia; Lahaye, François

2009-08-01

In recent years, many national timing laboratories have installed geodetic Global Positioning System receivers together with their traditional GPS/GLONASS Common View receivers and Two Way Satellite Time and Frequency Transfer equipment. Many of these geodetic receivers operate continuously within the International GNSS Service (IGS), and their data are regularly processed by IGS Analysis Centers. From its global network of over 350 stations and its Analysis Centers, the IGS generates precise combined GPS ephemeredes and station and satellite clock time series referred to the IGS Time Scale. A processing method called Precise Point Positioning (PPP) is in use in the geodetic community allowing precise recovery of GPS antenna position, clock phase, and atmospheric delays by taking advantage of these IGS precise products. Previous assessments, carried out at Istituto Nazionale di Ricerca Metrologica (INRiM; formerly IEN) with a PPP implementation developed at Natural Resources Canada (NRCan), showed PPP clock solutions have better stability over short/medium term than GPS CV and GPS P3 methods and significantly reduce the day-boundary discontinuities when used in multi-day continuous processing, allowing time-limited, campaign-style time-transfer experiments. This paper reports on follow-on work performed at INRiM and NRCan to further characterize and develop the PPP method for time transfer applications, using data from some of the National Metrology Institutes. We develop a processing procedure that takes advantage of the improved stability of the phase-connected multi-day PPP solutions while allowing the generation of continuous clock time series, more applicable to continuous operation/monitoring of timing equipment.

Spatiotemporal variation in the postseismic deformation of the 2011 Tohoku-oki earthquake revealed by seafloor geodetic observations

NASA Astrophysics Data System (ADS)

Tomita, F.; Kido, M.; Ohta, Y.; Hino, R.; Iinuma, T.

2016-12-01

Postseismic deformation following the 2011 Tohoku-oki earthquake has been detected by on- and off-shore geodetic observations. GPS/Acoustic (GPS/A) observations [Watanabe et al., 2014, GRL] just above the coseismic primary rupture area (PRA) show significant landward movement in contrast to the trench-ward movement of the on-shore GPS observations, which can be generally explained by viscoelastic relaxation [Sun et al., 2014, Nature]. Furthermore, Tomita et al. [2015, AGU] demonstrated along-trench variation of the postseismic deformation also using GPS/A observations. In this study, we show detailed spatiotemporal characteristics of the postseismic deformation using updated GPS/A measurement results. We employed 20 GPS/A sites located in Tohoku-oki region and had conducted repeated campaign surveys from Sep. 2012 to May 2016. GPS/A positioning was performed using the method of Kido et al. [2006, EPS]. Then, we calculated postseismic displacement rates by applying a weighted robust linear fitting. The updated results of the postseismic displacement rates are consistent with the characteristic revealed by Tomita et al. [2015] but are estimated with better precision ( 2 cm/yr in 1σ). The sites in the north region of PRA show slight trenchward movement (< 5 cm/yr), while the sites in the south region of PRA show significant trenchward movement (5-15 cm/yr) indicating dominance of the afterslip effects. Moreover, the sites above PRA show significant landward movement (10-15 cm/yr) indicating viscoelastic relaxation and interplate relocking effects. Furthermore, the updated results may show temporal decay of afterslip; the temporally decaying displacements have been observed in the south region of PRA. However, such a temporal decay has not been measured in the region where viscoelastic relaxation causes significant deformation. In the presentation, we will discuss detail spatiotemporal evolution of the postseismic deformation processes from the updated results by comparing with other geodetic observations and studies on the postseismic deformation modeling.

Carrier phase ambiguity resolution for the Global Positioning System applied to geodetic baselines up to 2000 km

NASA Technical Reports Server (NTRS)

Blewitt, Geoffrey

1989-01-01

A technique for resolving the ambiguities in the GPS carrier phase data (which are biased by an integer number of cycles) is described which can be applied to geodetic baselines up to 2000 km in length and can be used with dual-frequency P code receivers. The results of such application demonstrated that a factor of 3 improvement in baseline accuracy could be obtained, giving centimeter-level agreement with coordinates inferred by very-long-baseline interferometry in the western United States. It was found that a method using pseudorange data is more reliable than one using ionospheric constraints for baselines longer than 200 km. It is recommended that future GPS networks have a wide spectrum of baseline lengths (ranging from baselines shorter than 100 km to those longer than 1000 km) and that GPS receivers be used which can acquire dual-frequency P code data.

A Solution to Bring the National Astronomical-Geodetic Network from S/42 System to WGS-84 System

NASA Astrophysics Data System (ADS)

Radu, Ion

In the framework of a Romanian-Bulgarian cooperation, the Military Astronomical Observatory Bucharest integrated GPS measurements with points in the Southern zone of the national geodetic network. Molodensky's, Zhogolovich's and Ihde's relations were used to pass from S/42 system to WGS-84 system. Six variants for the choice of common points were considered.

Geodesy and the UNAVCO Consortium: Three Decades of Innovations

NASA Astrophysics Data System (ADS)

Rowan, L. R.; Miller, M. M.; Meertens, C. M.; Mattioli, G. S.

2015-12-01

UNAVCO, a non-profit, university consortium that supports geoscience research using geodesy, began with the ingenious recognition that the nascent Global Positioning System constellation (GPS) could be used to investigate earth processes. The consortium purchased one of the first commercially available GPS receivers, Texas Instrument's TI-4100 NAVSTAR Navigator, in 1984 to measure plate deformation. This early work was highlighted in a technology magazine, GPSWorld, in 1990. Over a 30-year period, UNAVCO and the community have helped advance instrument design for mobility, flexibility, efficiency and interoperability, so research could proceed with higher precision and under ever challenging conditions. Other innovations have been made in data collection, processing, analysis, management and archiving. These innovations in tools, methods and data have had broader impacts as they have found greater utility beyond research for timing, precise positioning, safety, communication, navigation, surveying, engineering and recreation. Innovations in research have expanded the utility of geodetic tools beyond the solid earth science through creative analysis of the data and the methods. For example, GPS sounding of the atmosphere is now used for atmospheric and space sciences. GPS reflectrometry, another critical advance, supports soil science, snow science and ecological research. Some research advances have had broader impacts for society by driving innovations in hazards risk reduction, hazards response, resource management, land use planning, surveying, engineering and other uses. Furthermore, the geodetic data is vital for the design of space missions, testing and advancing communications, and testing and dealing with interference and GPS jamming. We will discuss three decades (and counting) of advances by the National Science Foundation's premiere geodetic facility, consortium and some of the many geoscience principal investigators that have driven innovations in research, instrumentation, data management, cyberinfrastructure and other applications.

Combining various space geodetic techniques for regional modeling of ionospheric electron density over Iran

NASA Astrophysics Data System (ADS)

Zare, Saeed; Alizadeh, M. Mahdi; Schuh, Harald

2017-04-01

Ionosphere is a layer of the upper atmosphere, between the thermosphere and the exosphere, distinguished because it is ionized by solar radiation. As an important part of human living environment, ionosphere affects our modern society in many ways. International broadcasters use this medium to reflect radio signals back toward the Earth. Ionosphere provides long range capabilities for commercial ship-to-shore communications, for trans-oceanic aircraft links, and for military communication and surveillance systems. Space geodetic techniques have turned into a capable tool for studying the ionosphere in the last decades. Up to now, two dimensional (2-D) models of vertical TEC (VTEC) have been widely developed and used by different communities; however, due to the fact that these models provide information about the integral of the whole electron content along the vertical or slant ray path, these maps are not useful when information about the ionosphere at different altitude is required. The aim of this study is to develop three dimensional (3-D) regional model of electron density by using combination of various space geodetic techniques. B-Spline basis functions are used for longitude and latitude variations of the electron density and Chapman profile function for altitude variations. The National Cartographic Center of Iran (NCC) has established a network of one hundred GPS stations: The Iranian Permanent GPS Network for Geodynamics (IPGN). The main task of the GPS stations is to collect and store raw GPS data and send it to Tehran processing center on a daily basis for final processing. The required data for our investigation are ground based measurements of permanent GPS stations over Iran and radio occultation data from Formosat-3/Cosmic for region of interest. We expect to increase accuracy and reliability of final model by integrating different observation techniques.

Undergraduate teaching modules featuring geodesy data applied to critical social topics (GETSI: GEodetic Tools for Societal Issues)

NASA Astrophysics Data System (ADS)

Pratt-Sitaula, B. A.; Walker, B.; Douglas, B. J.; Charlevoix, D. J.; Miller, M. M.

2015-12-01

The GETSI project, funded by NSF TUES, is developing and disseminating teaching and learning materials that feature geodesy data applied to critical societal issues such as climate change, water resource management, and natural hazards (serc.carleton.edu/getsi). It is collaborative between UNAVCO (NSF's geodetic facility), Mt San Antonio College, and Indiana University. GETSI was initiated after requests by geoscience faculty for geodetic teaching resources for introductory and majors-level students. Full modules take two weeks but module subsets can also be used. Modules are developed and tested by two co-authors and also tested in a third classroom. GETSI is working in partnership with the Science Education Resource Center's (SERC) InTeGrate project on the development, assessment, and dissemination to ensure compatibility with the growing number of resources for geoscience education. Two GETSI modules are being published in October 2015. "Ice mass and sea level changes" includes geodetic data from GRACE, satellite altimetry, and GPS time series. "Imaging Active Tectonics" has students analyzing InSAR and LiDAR data to assess infrastructure earthquake vulnerability. Another three modules are in testing during fall 2015 and will be published in 2016. "Surface process hazards" investigates mass wasting hazard and risk using LiDAR data. "Water resources and geodesy" uses GRACE, vertical GPS, and reflection GPS data to have students investigating droughts in California and the High Great Plains. "GPS, strain, and earthquakes" helps students learn about infinitesimal and coseismic strain through analysis of horizontal GPS data and includes an extension module on the Napa 2014 earthquake. In addition to teaching resources, the GETSI project is compiling recommendations on successful development of geodesy curricula. The chief recommendations so far are the critical importance of including scientific experts in the authorship team and investing significant resources in data preparation (student interns can be excellent for this). GETSI also includes a research element on the way instructors adapt or adopt the resources. After publication, 4 additional testers will be recruited per module. They will provide feedback on how they choose to use the module elements in their courses.

Contribution to defining a geodetic reference frame for Africa (AFREF): Geodynamics implications

NASA Astrophysics Data System (ADS)

Saria, Elifuraha E.

African Reference Frame (AFREF) is the proposed regional three-dimensional standard frame, which will be used to reference positions and velocities for geodetic sites in Africa and surrounding. This frame will play a crucial role in scientific application for example plate motion and crustal deformation studies, and also in mapping when it involves for example national boundary surveying, remote sensing, GIS, engineering projects and other development programs in Africa. To contribute to the definition of geodetic reference frame for Africa and provide the first continent-wide position/velocity solution for Africa, we processed and analyzed 16 years of GPS and 17 years of DORIS data at 133 GPS sites and 9 DORIS sites continuously operating geodetic sites in Africa and surroundings to describe the present-day kinematics of the Nubian and Somalian plates and constrain relative motions across the East African Rift. We use the resulting horizontal velocities to determine the level of rigidity of Nubia and updated a plate motion model for the East African Rift and revise the counter clockwise rotation of the Victoria plate and clockwise rotation of the Rovuma plate with respect to Nubia. The vertical velocity ranges from -2 to +2 mm/yr, close to their uncertainties with no clear geographical pattern. This study provides the first continent-wide position/velocity solution for Africa, expressed in International Terrestrial Reference Frame (ITRF2008), a contribution to the upcoming African Reference Frame (AFREF). In the next step we used the substantial increase in the geologic, geophysical and geodetic data in Africa to improve our understanding of the rift geometry and the block kinematics of the EAR. We determined the best-fit fault structure of the rift in terms of the locking depth and dip angle and use a block modeling approach where observed velocities are described as the contribution of rigid block rotation and strain accumulation on locked faults. Our results show a better fit with three sub-plates (Victoria, Rovuma and Lwandle) between the major plates Nubia and Somalia. We show that the earthquake slip vectors provide information that is consistent with the GPS velocities and significantly help reduce the uncertainties in plate angular velocity estimates. However, we find that 3.16 My average spreading rates along the Southwest Indian Ridge (SWIR) from MORVEL model are systematically faster than GPS-derived motions across that ridge, possibly reflecting the need to revise the MORVEL outward displacement correction. In the final step, we attempt to understand the hydrological loading in Africa, which may affect our geodetic estimates, particularly the uplift rates. In this work, we analyze 10 years (2002 - 2012) of continuous GPS measurements operating in Africa, and compare with the modeled hydrological loading deformation inferred from the Gravity Recovery and Climate Experiment (GRACE) at the same GPS location and for the same time period. We estimated hydrological loading deformation based on the Equivalent Water Height (EWH) derived from the 10-days interval reprocessed GRACE solution second release (RL02). We took in to account in both GPS and GRACE the systematic errors from atmospheric pressure and non-tidal ocean loading effects and model the Earth as perfect elastic and compute the deformation using appropriate Greens function. We analyze the strength of association between the observation (GPS) and the model (GRACE) in terms of annual amplitude and phase as well as the original data (time-series). We find a good correlation mainly in regions associated with strong seasonal hydrological variations. To improve the correlation between the two solutions, we subtract the GRACE-derived vertical displacement from GPS-observed time series and determine the variance reduction. Our solution shows average variance between the model and the observation reduced to ~40%. (Abstract shortened by UMI.)

TIGO: a geodetic observatory for the improvement of the global reference frame

NASA Astrophysics Data System (ADS)

Schlueter, Wolfgang; Hase, Hayo; Boeer, Armin

1999-12-01

The Bundesamt fuer Kartographie und Geodaesie (BKG) will provide a major contribution to the improvement and maintenance of the global reference frames: ICRF (International Celestial Reference Frame), ITRF (International Terrestrial Reference Frame) with the operation of TIGO (Transportable Integrated Geodetic Observatory). TIGO is designed as a transportable geodetic observatory which consists of all relevant geodetic space techniques for a fundamental station (including VLBI, SLR, GPS). The transportability of the observatory enables to fill up gaps in the International Space Geodetic Network and to optimize the contribution to the global reference frames. TIGO should operate for a period of 2 to 3 years (at minimum) at one location. BKG is looking for a cooperation with countries willing to contribute to the ITRF and to support the operation of TIGO.

A Recommendation on SLR Ranging to Future Global Navigation Satellite Systems

NASA Astrophysics Data System (ADS)

Labrecque, J. L.; Miller, J. J.; Pearlman, M.

2008-12-01

The multi-agency US Geodetic Requirements Working Group has recommended that Satellite Laser Retro- reflectors be installed on GPS III satellites as a principal component of the Positioning, Navigation, and Timing mandate of the Global Positioning System. The Working Group, which includes NASA, NGA, NOAA, NRL, USGS, and the USNO, echoes the Global Geodetic Observing System recommendation that SLR retro- reflectors be installed on all GNSS satellites. It is further recommended that the retro-reflectors conform to and hopefully exceed the minimum standard of the International Laser Ranging Service for retro-reflector cross sections of 100 million square meters for the HEO GNSS satellites to insure sufficiently accurate ranging by the global network of satellite laser ranging systems. The objective of this recommendation is to contribute to the improvement in the International Terrestrial Reference Frame, and its derivative the WGS84 reference frame, through continuing improvements in the characterization of the GPS orbits and clocks. Another objective is to provide an independent means of assessing the interoperability and accuracy of the GNSS systems and regional augmentation systems. The ranging to GNSS-mounted retro-reflectors will constitute a significant new means of space-based collocation to constrain the tie between the GPS and SLR networks that constitute over 50% of the data from which the ITRF is derived. The recommendation for the installation of SLR retro-reflectors aboard future GPS satellites is one of a number of efforts aimed at improving the accuracy and stability of ITRF. These steps are being coordinated with and supportive of the efforts of the GGOS and its services such at the VLBI2010 initiative, developing a next generation geodetic network, near real-time GPS positioning and EOP determination, and numerous efforts in the improvement of geodetic algorithms for GPS, SLR, VLBI, DORIS, and the determination of the ITRF. If past is prologue, the requirements of accuracy placed upon GNSS systems will continue to evolve at a factor of ten per decade for the lifetime of the GPS III, extending to 2025 and beyond. Global societal priorities such as sea level change measurement already require a factor of ten or more improvement in the accuracy and stability of the ITRF. Increasing accuracy requirements by civilian users for precision positioning and time keeping will certainly continue to grow at an exponential rate. The PNT accuracy of our GNSS systems will keep pace with these societal needs only if we equip the GNSS systems with the capability to identify and further reduce systematic errors.

Preliminary study of GPS orbit determination accuracy achievable from worldwide tracking data

NASA Technical Reports Server (NTRS)

Larden, D. R.; Bender, P. L.

1982-01-01

The improvement in the orbit accuracy if high accuracy tracking data from a substantially larger number of ground stations is available was investigated. Observations from 20 ground stations indicate that 20 cm or better accuracy can be achieved for the horizontal coordinates of the GPS satellites. With this accuracy, the contribution to the error budget for determining 1000 km baselines by GPS geodetic receivers would be only about 1 cm.

Carrier-phase time transfer.

PubMed

Larson, K M; Levine, J

1999-01-01

We have conducted several time-transfer experiments using the phase of the GPS carrier rather than the code, as is done in current GPS-based time-transfer systems. Atomic clocks were connected to geodetic GPS receivers; we then used the GPS carrier-phase observations to estimate relative clock behavior at 6-minute intervals. GPS carrier-phase time transfer is more than an order of magnitude more precise than GPS common view time transfer and agrees, within the experimental uncertainty, with two-way satellite time-transfer measurements for a 2400 km baseline. GPS carrier-phase time transfer has a stability of 100 ps, which translates into a frequency uncertainty of about two parts in 10(-15) for an average time of 1 day.

Global reference frame: Intercomparison of results (SLR, VLBI and GPS)

NASA Technical Reports Server (NTRS)

Ma, Chopo; Watkins, Michael M.; Heflin, M.

1994-01-01

The terrestrial reference frame (TRF) is realized by a set of positions and velocities derived from a combination of the three space geodetic techniques, SLR, VLBI and GPS. The standard International TRF is constructed by the International Earth Rotation Service in such a way that it is stable with time and the addition of new data. An adopted model for overall plate motion, NUVEL-1 NNR, defines the conceptual reference frame in which all the plates are moving. In addition to the measurements made between reference points within the space geodetic instruments, it is essential to have accurate, documented eccentricity measurements from the instrument reference points to ground monuments. Proper local surveys between the set of ground monuments at a site are also critical for the use of the space geodetic results. Eccentricities and local surveys are, in fact, the most common and vexing sources of error in the use of the TRF for such activities as collocation and intercomparison.

Outreach on a National Scale: The Critical Role of Facilities

NASA Astrophysics Data System (ADS)

Bartel, B. A.; Charlevoix, D. J.

2015-12-01

Facilities provide infrastructure for science that would not be feasible at a single institution. Facilities are also a resource for development of outreach products and activities that reach a national audience of diverse stakeholders. UNAVCO manages the NSF geodetic facility GAGE (Geodesy Advancing Geosciences and Earthscope). Staff at UNAVCO with expertise in education, outreach, and communication translate the science and supporting infrastructure into materials consumable by a wide array of users including teachers, students, museum attendees, emergency managers, park interpreters, and members of the general public. UNAVCO has the ability to distribute materials to a national and international audience, thereby greatly increasing the impact of the science and increasing the value of the investment by the National Science Foundation. In 2014 and 2015, UNAVCO produced multiple print products focused on the Plate Boundary Observatory (PBO), the geodetic component of EarthScope. Products include a deck of playing cards featuring PBO GPS stations, a poster featuring GPS velocities of the Western United States, and another poster focused on GPS velocities in Alaska. We are distributing these products to a broad audience, including teachers, station permit holders, and community members. The Tectonics of the Western United States poster was distributed this year in the American Geosciences Institute Earth Science Week kit for teachers, reaching 16,000 educators around the country. These posters and the PBO playing cards (PBO-52) were distributed to more than 100 teachers through workshops led by UNAVCO, the EarthScope National Office, the Southern California Earthquake Center (SCEC), and more. Additionally, these cards serve as a way to engage landowners who host these scientific stations on their property. This presentation will address the strategies for creating nationally relevant materials and the tools used for dissemination of materials to a broad audience. We will outline the process of our planning strategy as well as share ways in which we evaluate impact of particular outreach products and the overall outreach program.

Determination of recent horizontal crustal movements and deformations of African and Eurasian plates in western Mediterranean region using geodetic-GPS computations extended to 2006 (from 1997) related to NAFREF and AFREF frames.

NASA Astrophysics Data System (ADS)

Azzouzi, R.

2009-04-01

Determination of recent horizontal crustal movements and deformations of African and Eurasian plates in western Mediterranean region using geodetic-GPS computations extended to 2006 (from 1997) related to NAFREF and AFREF frames. By: R. Azzouzi*, M. Ettarid*, El H. Semlali*, et A. Rimi+ * Filière de Formation en Topographie Institut Agronomique et Vétérinaire Hassan II B.P. 6202 Rabat-Instituts MAROC + Département de la Physique du Globe Université Mohammed V Rabat MAROC This study focus on the use of the geodetic spatial technique GPS for geodynamic purposes generally in the Western Mediterranean area and particularly in Morocco. It aims to exploit this technique first to determine the geodetic coordinates on some western Mediterranean sites. And also this technique is used to detect and to determine movements cross the boundary line between the two African and Eurasian crustal plates on some well chosen GPS-Geodynamics sites. It will allow us also to estimate crustal dynamic parameters of tension that results. These parameters are linked to deformations of terrestrial crust in the region. They are also associated with tectonic constraints of the study area. The usefulness of repeated measurements of these elements, the estimate of displacements and the determination of their temporal rates is indisputable. Indeed, sismo-tectonique studies allow a good knowledge of the of earthquake processes, their frequency their amplitude and even of their prediction in the world in general and in Moroccan area especially. They allow also contributing to guarantee more security for all most important management projects, as projects of building great works (dams, bridges, nuclear centrals). And also as preliminary study, for the most important joint-project between Europe and Africa through the Strait of Gibraltar. For our application, 23 GPS monitoring stations under the ITRF2000 reference frame are chosen in Eurasian and African plates. The sites are located around the Western Mediterranean and especially on Morocco. Exploiting parameters of positions and dispersions of these stations within the 1997-2003 period, the motion and the interaction types of interaction between African and Eurasian tectonic plates can be estimated. Similarly, the crustal dynamic parameters of tension of these sites will be computed. The time occupation on repeated observations sites is at least 72 hours. The measurements are continuous on permanent stations. The precise ephemerides are used in GPS computations. The post-treatments are done using commercial and scientific softwares. The coordinates obtained for two consecutive periods to and t within a period of 8 years will be used by programs established for this purpose to estimate crustal dynamic parameters of tension as well as to evaluate the appropriate movements. Even crustal dynamic parameters will be determined on each sites of the GPS-Geodynamics network, whose interest of seismic investigations is very important. This will allow best knowledge of substantial seismic activities of the surrounding zones. It can be deduced by measuring the motions and their parameter tensions using GPS. These estimations will contribute on the earthquake prediction by supervising the strain accumulation and its release in the active areas. For the geodetically aspect the GPS-Geodynamics sites computed in the ITRF frame can be used with other similar ounces' of Africa country and some well selected and convenient IGS, EUREF stations..to determine first the NAFREF and the AFRER frames.

West-Coast Wide Expansion and Testing of the Geodetic Alarm System (G-larmS)

NASA Astrophysics Data System (ADS)

Ruhl, C. J.; Grapenthin, R.; Melgar, D.; Aranha, M. A.; Allen, R. M.

2016-12-01

The Geodetic Alarm System (G-larmS) was developed in collaboration between the Berkeley Seismological Laboratory (BSL) and New Mexico Tech for real-time Earthquake Early Warning (EEW). G-larmS has been in continuous operation at the BSL since 2014 using event triggers from the ShakeAlert EEW system and real-time position time series from a fully triangulated network consisting of BARD, PBO and USGS stations across northern California (CA). G-larmS has been extended to include southern CA and Cascadia, providing continuous west-coast wide coverage. G-larmS currently uses high rate (1 Hz), low latency (< 5 s), accurate positioning (cm level) time series data from a regional GPS network and P-wave event triggers from the ShakeAlert EEW system. It extracts static offsets from real-time GPS time series upon S-wave arrival and performs a least squares inversion on these offsets to determine slip on a finite fault. A key issue with geodetic EEW approaches is that unlike seismology-based algorithms that are routinely tested using frequent small-magnitude events, geodetic systems are not regularly exercised. Scenario ruptures are therefore important for testing the performance of G-larmS. We discuss results from scenario events on several large faults (capable of M>6.5) in CA and Cascadia built from realistic 3D geometries. Synthetic long-period 1Hz displacement waveforms were obtained from a new stochastic kinematic slip distribution generation method. Waveforms are validated by direct comparison to peak P-wave displacement scaling laws and to PGD GMPEs obtained from high-rate GPS observations of large events worldwide. We run the scenarios on real-time streams to systematically test the recovery of slip and magnitude by G-larmS. In addition to presenting these results, we will discuss new capabilities, such as implementing 2D geometry and the applicability of these results to GPS enhanced tsunami warning systems.

Precision GPS orbit determination strategies for an earth orbiter and geodetic tracking system

NASA Technical Reports Server (NTRS)

Lichten, Stephen M.; Bertiger, Willy I.; Border, James S.

1988-01-01

Data from two 1985 GPS field tests were processed and precise GPS orbits were determined. With a combined carrier phase and pseudorange, the 1314-km repeatability improves substantially to 5 parts in 10 to the 9th (0.6 cm) in the north and 2 parts in 10 to the 8th (2-3 cm) in the other components. To achieve these levels of repeatability and accuracy, it is necessary to fine-tune the GPS solar radiation coefficients and ground station zenith tropospheric delays.

Geodetic Strain Analysis Tool

NASA Technical Reports Server (NTRS)

Kedar, Sharon; Baxter, Sean C.; Parker, Jay W.; Webb, Frank H.; Owen, Susan E.; Sibthorpe, Anthony J.; Dong, Danan

2011-01-01

A geodetic software analysis tool enables the user to analyze 2D crustal strain from geodetic ground motion, and create models of crustal deformation using a graphical interface. Users can use any geodetic measurements of ground motion and derive the 2D crustal strain interactively. This software also provides a forward-modeling tool that calculates a geodetic velocity and strain field for a given fault model, and lets the user compare the modeled strain field with the strain field obtained from the user s data. Users may change parameters on-the-fly and obtain a real-time recalculation of the resulting strain field. Four data products are computed: maximum shear, dilatation, shear angle, and principal components. The current view and data dependencies are processed first. The remaining data products and views are then computed in a round-robin fashion to anticipate view changes. When an analysis or display parameter is changed, the affected data products and views are invalidated and progressively re-displayed as available. This software is designed to facilitate the derivation of the strain fields from the GPS and strain meter data that sample it to facilitate the understanding of the strengths and weaknesses of the strain field derivation from continuous GPS (CGPS) and other geodetic data from a variety of tectonic settings, to converge on the "best practices" strain derivation strategy for the Solid Earth Science ESDR System (SESES) project given the CGPS station distribution in the western U.S., and to provide SESES users with a scientific and educational tool to explore the strain field on their own with user-defined parameters.

Monitoring Sea Level by Tide Gauges and GPS at Estartit and Barcelona Sites for Altimeter Calibration Campaigns

NASA Astrophysics Data System (ADS)

Martinez-Benjain, Juan Jose; Gili, Josep; Lopez, Rogelio; Tapia, Ana; Bosch, Ernest; Perez, Begona; Pros, Francesc

2013-09-01

The presentation is directed to the description of the actual geodetic infrastructure of Barcelona and l'Estartit sites for sea level monitoring by tide gauges and GPS and complementing Ibiza site for a new altimeter calibration campaign of Jason-2 and Saral/AltiKa satellites to be made in 2013.

Observation model and parameter partials for the JPL geodetic (GPS) modeling software 'GPSOMC'

NASA Technical Reports Server (NTRS)

Sovers, O. J.

1990-01-01

The physical models employed in GPSOMC, the modeling module of the GIPSY software system developed at JPL for analysis of geodetic Global Positioning Satellite (GPS) measurements are described. Details of the various contributions to range and phase observables are given, as well as the partial derivatives of the observed quantities with respect to model parameters. A glossary of parameters is provided to enable persons doing data analysis to identify quantities with their counterparts in the computer programs. The present version is the second revision of the original document which it supersedes. The modeling is expanded to provide the option of using Cartesian station coordinates; parameters for the time rates of change of universal time and polar motion are also introduced.

Accuracy improvement techniques in Precise Point Positioning method using multiple GNSS constellations

NASA Astrophysics Data System (ADS)

Vasileios Psychas, Dimitrios; Delikaraoglou, Demitris

2016-04-01

The future Global Navigation Satellite Systems (GNSS), including modernized GPS, GLONASS, Galileo and BeiDou, offer three or more signal carriers for civilian use and much more redundant observables. The additional frequencies can significantly improve the capabilities of the traditional geodetic techniques based on GPS signals at two frequencies, especially with regard to the availability, accuracy, interoperability and integrity of high-precision GNSS applications. Furthermore, highly redundant measurements can allow for robust simultaneous estimation of static or mobile user states including more parameters such as real-time tropospheric biases and more reliable ambiguity resolution estimates. This paper presents an investigation and analysis of accuracy improvement techniques in the Precise Point Positioning (PPP) method using signals from the fully operational (GPS and GLONASS), as well as the emerging (Galileo and BeiDou) GNSS systems. The main aim was to determine the improvement in both the positioning accuracy achieved and the time convergence it takes to achieve geodetic-level (10 cm or less) accuracy. To this end, freely available observation data from the recent Multi-GNSS Experiment (MGEX) of the International GNSS Service, as well as the open source program RTKLIB were used. Following a brief background of the PPP technique and the scope of MGEX, the paper outlines the various observational scenarios that were used in order to test various data processing aspects of PPP solutions with multi-frequency, multi-constellation GNSS systems. Results from the processing of multi-GNSS observation data from selected permanent MGEX stations are presented and useful conclusions and recommendations for further research are drawn. As shown, data fusion from GPS, GLONASS, Galileo and BeiDou systems is becoming increasingly significant nowadays resulting in a position accuracy increase (mostly in the less favorable East direction) and a large reduction of convergence time in PPP static and kinematic solutions compared to GPS-only PPP solutions for various observational session durations. However, this is mostly observed when the visibility of Galileo and BeiDou satellites is substantially long within an observational session. In GPS-only cases dealing with data from high elevation cut-off angles, the number of GPS satellites decreases dramatically, leading to a position accuracy and convergence time deviating from satisfactory geodetic thresholds. By contrast, respective multi-GNSS PPP solutions not only show improvement, but also lead to geodetic level accuracies even in 30° elevation cut-off. Finally, the GPS ambiguity resolution in PPP processing is investigated using the GPS satellite wide-lane fractional cycle biases, which are included in the clock products by CNES. It is shown that their addition shortens the convergence time and increases the position accuracy of PPP solutions, especially in kinematic mode. Analogous improvement is obtained in respective multi-GNSS solutions, even though the GLONASS, Galileo and BeiDou ambiguities remain float, since information about them is not provided in the clock products available to date.

A geodetic matched filter search for slow slip with application to the Mexico subduction zone

NASA Astrophysics Data System (ADS)

Rousset, B.; Campillo, M.; Lasserre, C.; Frank, W. B.; Cotte, N.; Walpersdorf, A.; Socquet, A.; Kostoglodov, V.

2017-12-01

Since the discovery of slow slip events, many methods have been successfully applied to model obvious transient events in geodetic time series, such as the widely used network strain filter. Independent seismological observations of tremors or low-frequency earthquakes and repeating earthquakes provide evidence of low-amplitude slow deformation but do not always coincide with clear occurrences of transient signals in geodetic time series. Here we aim to extract the signal corresponding to slow slips hidden in the noise of GPS time series, without using information from independent data sets. We first build a library of synthetic slow slip event templates by assembling a source function with Green's functions for a discretized fault. We then correlate the templates with postprocessed GPS time series. Once the events have been detected in time, we estimate their duration T and magnitude Mw by modeling a weighted stack of GPS time series. An analysis of synthetic time series shows that this method is able to resolve the correct timing, location, T, and Mw of events larger than Mw 6 in the context of the Mexico subduction zone. Applied on a real data set of 29 GPS time series in the Guerrero area from 2005 to 2014, this technique allows us to detect 28 transient events from Mw 6.3 to 7.2 with durations that range from 3 to 39 days. These events have a dominant recurrence time of 40 days and are mainly located at the downdip edges of the Mw>7.5 slow slip events.

A geodetic matched-filter search for slow slip with application to the Mexico subduction zone

NASA Astrophysics Data System (ADS)

Rousset, B.; Campillo, M.; Lasserre, C.; Frank, W.; Cotte, N.; Walpersdorf, A.; Socquet, A.; Kostoglodov, V.

2017-12-01

Since the discovery of slow slip events, many methods have been successfully applied to model obvious transient events in geodetic time series, such as the widely used network strain filter. Independent seismological observations of tremors or low frequency earthquakes and repeating earthquakes provide evidence of low amplitude slow deformation but do not always coincide with clear occurrences of transient signals in geodetic time series. Here, we aim to extract the signal corresponding to slow slips hidden in the noise of GPS time series, without using information from independent datasets. We first build a library of synthetic slow slip event templates by assembling a source function with Green's functions for a discretized fault. We then correlate the templates with post-processed GPS time series. Once the events have been detected in time, we estimate their duration T and magnitude Mw by modelling a weighted stack of GPS time series. An analysis of synthetic time series shows that this method is able to resolve the correct timing, location, T and Mw of events larger than Mw 6.0 in the context of the Mexico subduction zone. Applied on a real data set of 29 GPS time series in the Guerrero area from 2005 to 2014, this technique allows us to detect 28 transient events from Mw 6.3 to 7.2 with durations that range from 3 to 39 days. These events have a dominant recurrence time of 40 days and are mainly located at the down dip edges of the Mw > 7.5 SSEs.

GPS application to mapping, charting and geodesy

NASA Technical Reports Server (NTRS)

Senus, W. J.; Hill, R. W.

1981-01-01

GPSPAC, a receiver being developed for space applications by the Defense Mapping Agency and NASA, will use signals from GPS constellations to generate real-time values of host vehicle position and velocity. The GPSPAC has an L-band antenna and preamp capable of receiving the 1575 MHz and 1227 MHz spread spectrum signals; its stable oscillator at 5.115 MHz provides the basic frequency reference, resulting in a long term drift of less than one part in 10 to the -10th day. The GPSPAC performs many functions on board the spacecraft which were previously relegated to large-scale ground-based computer/receiver systems. A positional accuracy of better than 8 can be achieved for those periods when four or more NAVSTAR satellites are visible to the host satellite. The GPS geodetic receiver development, which will provide prototype receivers for utilization in terrestrial surveying operations, has the potential to significantly enhance the accuracy of point geodetic surveys over the current user hardware capability.

Installation of a seafloor geodetic network offshore northern Chile (GeoSEA)

NASA Astrophysics Data System (ADS)

Kopp, Heidrun; Lange, Dietrich; Hannemann, Katrin; Petersen, Florian; Contreras-Reyes, Eduardo

2016-04-01

The seafloor stores crucial information on sub-seafloor processes, including stress, elastic strain, and earthquake and tsunami generation. This information may be extracted through the nascent scientific field of seafloor geodesy. The target of the recently installed GeoSEA array (Geodetic Earthquake Observatory on the SEAfloor) is to measure crustal deformation in mm-scale on the marine forearc and outer rise of the South American subduction system around 21°S. This segment of the Nazca-South American plate boundary has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique/Pisagua earthquake (Mw=8.1). The southern portion of the segment remains unbroken by a recent earthquake. Seafloor geodetic measurements provide a way to monitor crustal deformation at high resolution comparable to the satellite-based GPS technique upon which terrestrial geodesy is largely based. The GeoSEA Network consists of autonomous seafloor transponders installed on 4 m high tripods, which were lowered to the seabed on the deep-sea cable of RV SONNE in December 2015. The transponders within an array intercommunicate via acoustic signals for a period of up to 3.5 years and measure acoustic distance, tilt and pressure. An additional component of the network is GeoSURF, a self-steering autonomous surface vehicle (Wave Glider), which monitors system health and is capable to upload the seafloor data to the sea surface and to transfer it via satellite. We have chosen three areas on the middle and lower slope and the outer rise for the set-up of three sub-arrays. The array in Area 1 on the middle continental slope consists of 8 transponders located in pairs on four topographic ridges, which are surface expressions of faults at depth. Area 2 is located on the outer rise seaward of the trench where 5 stations monitor extension across plate-bending related normal faults. The third area is located at water depth >5000 m on the lower continental slope where an array of 10 stations measures diffuse strain build-up. Data from all networks and all stations were successfully uploaded to GeoSURF and/or a high performance USBL transceiver lowered into the water from RV SONNE. The seabed installation of a total of 23 transponders records pressure, temperature, water sound velocity, salinity, and baselines between stations. Baselines cover distances of up to 2600 m with a precision of ±2 mm.

Polarization Analysis of the September 2005 Northern Cascadia Episodic Tremor and Slip Event

NASA Astrophysics Data System (ADS)

Wech, A. G.; Creager, K. C.

2006-12-01

The region of Northern Cascadia, extending from the Olympic Mountains and Puget Sound to southern Vancouver Island, down-dip of the subduction "locked" zone has repeatedly experienced episodes of slow slip. This episodic slip, observed to take place over a period of two to several weeks, is accompanied by a seismic tremor signal. Based on the average recurrence interval of 14 months, the last episodic tremor and slip (ETS) event was expected to occur in September, 2005. Indeed, it began on September 3. In order to record this event, we deployed an array of 11 three-component seismometers on the northern side of the Olympic Peninsula augmenting Pacific Northwest Seismographic Network stations as well as the first few EarthScope BigFoot stations and Plate Boundary Observatory borehole seismometers. This seismic array was comprised of six short-period and five broadband instruments with average spacings of 500 m and 2200 m respectively. In conjunction with this Earthscope seismic deployment, we also installed a dense network of 29 temporary, continuous GPS stations across the entire Olympic Peninsula to integrate seismic and geodetic observations. Based on past geodetic observations, a dominant assumption for the source of tremor is fault-slip in the direction of subduction, which can be tested using polarization of the seismic tremor. Using waveform cross- correlation to invert for the direction of slowness, we observed the tremor signal to migrate directly under our array. As the source passed beneath the array, tremor polarization stabilized to coincide with the direction of subduction. During a four day period starting September 8, the normalized eigenvalue associated with the dominant linear polarization jumped from ~0.7 to a stable 0.9 value. Also during this time, the polarization azimuth stabilized to a value of 57 +/- 8 degrees, close to the angle of subduction (56 degrees) suggesting that the tremor is caused by slip in the direction of relative plate motion on one or more faults.

A new velocity field for Africa from combined GPS and DORIS space geodetic Solutions: Contribution to the definition of the African reference frame (AFREF)

NASA Astrophysics Data System (ADS)

Saria, E.; Calais, E.; Altamimi, Z.; Willis, P.; Farah, H.

2013-04-01

We analyzed 16 years of GPS and 17 years of Doppler orbitography and radiopositioning integrated by satellite (DORIS) data at continuously operating geodetic sites in Africa and surroundings to describe the present-day kinematics of the Nubian and Somalian plates and constrain relative motions across the East African Rift. The resulting velocity field describes horizontal and vertical motion at 133 GPS sites and 9 DORIS sites. Horizontal velocities at sites located on stable Nubia fit a single plate model with a weighted root mean square residual of 0.6 mm/yr (maximum residual 1 mm/yr), an upper bound for plate-wide motions and for regional-scale deformation in the seismically active southern Africa and Cameroon volcanic line. We confirm significant southward motion ( ˜ 1.5 mm/yr) in Morocco with respect to Nubia, consistent with earlier findings. We propose an updated angular velocity for the divergence between Nubia and Somalia, which provides the kinematic boundary conditions to rifting in East Africa. We update a plate motion model for the East African Rift and revise the counterclockwise rotation of the Victoria plate and clockwise rotation of the Rovuma plate with respect to Nubia. Vertical velocities range from - 2 to +2 mm/yr, close to their uncertainties, with no clear geographic pattern. This study provides the first continent-wide position/velocity solution for Africa, expressed in International Terrestrial Reference Frame (ITRF2008), a contribution to the upcoming African Reference Frame (AFREF). Except for a few regions, the African continent remains largely under-sampled by continuous space geodetic data. Efforts are needed to augment the geodetic infrastructure and openly share existing data sets so that the objectives of AFREF can be fully reached.

Combining Real-time Seismic and Geodetic Data to Improve Rapid Earthquake Information

NASA Astrophysics Data System (ADS)

Murray, M. H.; Neuhauser, D. S.; Gee, L. S.; Dreger, D. S.; Basset, A.; Romanowicz, B.

2002-12-01

The Berkeley Seismological Laboratory operates seismic and geodetic stations in the San Francisco Bay area and northern California for earthquake and deformation monitoring. The seismic systems, part of the Berkeley Digital Seismic Network (BDSN), include strong motion and broadband sensors, and 24-bit dataloggers. The data from 20 GPS stations, part of the Bay Area Regional Deformation (BARD) network of more than 70 stations in northern California, are acquired in real-time. We have developed methods to acquire GPS data at 12 stations that are collocated with the seismic systems using the seismic dataloggers, which have large on-site data buffer and storage capabilities, merge it with the seismic data stream in MiniSeed format, and continuously stream both data types using reliable frame relay and/or radio modem telemetry. Currently, the seismic data are incorporated into the Rapid Earthquake Data Integration (REDI) project to provide notification of earthquake magnitude, location, moment tensor, and strong motion information for hazard mitigation and emergency response activities. The geodetic measurements can provide complementary constraints on earthquake faulting, including the location and extent of the rupture plane, unambiguous resolution of the nodal plane, and distribution of slip on the fault plane, which can be used, for example, to refine strong motion shake maps. We are developing methods to rapidly process the geodetic data to monitor transient deformation, such as coseismic station displacements, and for combining this information with the seismic observations to improve finite-fault characterization of large earthquakes. The GPS data are currently processed at hourly intervals with 2-cm precision in horizontal position, and we are beginning a pilot project in the Bay Area in collaboration with the California Spatial Reference Center to do epoch-by-epoch processing with greater precision.

Resolution analysis of finite fault source inversion using one- and three-dimensional Green's functions 2. Combining seismic and geodetic data

USGS Publications Warehouse

Wald, D.J.; Graves, R.W.

2001-01-01

Using numerical tests for a prescribed heterogeneous earthquake slip distribution, we examine the importance of accurate Green's functions (GF) for finite fault source inversions which rely on coseismic GPS displacements and leveling line uplift alone and in combination with near-source strong ground motions. The static displacements, while sensitive to the three-dimensional (3-D) structure, are less so than seismic waveforms and thus are an important contribution, particularly when used in conjunction with waveform inversions. For numerical tests of an earthquake source and data distribution modeled after the 1994 Northridge earthquake, a joint geodetic and seismic inversion allows for reasonable recovery of the heterogeneous slip distribution on the fault. In contrast, inaccurate 3-D GFs or multiple 1-D GFs allow only partial recovery of the slip distribution given strong motion data alone. Likewise, using just the GPS and leveling line data requires significant smoothing for inversion stability, and hence, only a blurred vision of the prescribed slip is recovered. Although the half-space approximation for computing the surface static deformation field is no longer justifiable based on the high level of accuracy for current GPS data acquisition and the computed differences between 3-D and half-space surface displacements, a layered 1-D approximation to 3-D Earth structure provides adequate representation of the surface displacement field. However, even with the half-space approximation, geodetic data can provide additional slip resolution in the joint seismic and geodetic inversion provided a priori fault location and geometry are correct. Nevertheless, the sensitivity of the static displacements to the Earth structure begs caution for interpretation of surface displacements, particularly those recorded at monuments located in or near basin environments. Copyright 2001 by the American Geophysical Union.

Need for denser geodetic network to get real constrain on the fault behavior along the Main Marmara Sea segments of the NAF, toward an optimized GPS network.

NASA Astrophysics Data System (ADS)

Klein, E.; Masson, F.; Duputel, Z.; Yavasoglu, H.; Agram, P. S.

2016-12-01

Over the last two decades, the densification of GPS networks and the development of new radar satellites offered an unprecedented opportunity to study crustal deformation due to faulting. Yet, submarine strike slip fault segments remain a major issue, especially when the landscape appears unfavorable to the use of SAR measurements. It is the case of the North Anatolian fault segments located in the Main Marmara Sea, that remain unbroken ever since the Mw7.4 earthquake of Izmit in 1999, which ended a eastward migrating seismic sequence of Mw > 7 earthquakes. Located directly offshore Istanbul, evaluation of seismic hazard appears capital. But a strong controversy remains over whether these segments are accumulating strain and are likely to experience a major earthquake, or are creeping, resulting both from the simplicity of current geodetic models and the scarcity of geodetic data. We indeed show that 2D infinite fault models cannot account for the complexity of the Marmara fault segments. But current geodetic data in the western region of Istanbul are also insufficient to invert for the coupling using a 3D geometry of the fault. Therefore, we implement a global optimization procedure aiming at identifying the most favorable distribution of GPS stations to explore the strain accumulation. We present here the results of this procedure that allows to determine both the optimal number and location of the new stations. We show that a denser terrestrial survey network can indeed locally improve the resolution on the shallower part of the fault, even more efficiently with permanent stations. But data closer from the fault, only possible by submarine measurements, remain necessary to properly constrain the fault behavior and its potential along strike coupling variations.

Societal challenges-oriented data-rich undergraduate teaching resources for geoscience classrooms and field courses

NASA Astrophysics Data System (ADS)

Pratt-Sitaula, B. A.; Walker, B.; Douglas, B. J.; Crosby, B. T.; Charlevoix, D. J.; Crosby, C. J.; Shervais, K.

2016-12-01

The NSF-funded GEodesy Tools for Societal Issues (GETSI) project is developing modules for use in introductory and majors-level courses that emphasize a broad range of geodetic data and quantitative skills applied to societally important issues of climate change, natural hazards, and water resources (serc.carleton.edu/getsi). The modules fill gaps in existing undergraduate curricula, which seldom include geodetic methods. Published modules are "Ice mass and sea level changes", "Imaging active tectonics with LiDAR and InSAR", "Measuring water resources with GPS, gravity, and traditional methods", "Surface process hazards", and "GPS, strain, and earthquakes". The GETSI Field Collection features geodetic field techniques. The field-oriented module "Analyzing high resolution topography with terrestrial laser scanning (TLS) and structure from motion (SfM)" is already published and "High precision positioning with static and kinematic GPS" will be published in 2017. Modules are 1-3 weeks long and include student exercises, data analysis, and extensive supporting materials. For field modules, prepared data sets are provided for courses that cannot collect field data directly. All modules were designed and developed by teams of faculty and content experts and underwent rigorous review and classroom testing. Collaborating institutions are UNAVCO (which runs NSF's Geodetic Facility), Indiana University, Mt San Antonio College, and Idaho State University. Science Education Resource Center (SERC) is providing assessment and evaluation expertise. If future funding is successful, the topic range will be expanded (e.g., volcanic hazards, more water resources, and ecological applications of geodesy). Funding to date has been provided by NSF's TUES (Transforming Undergraduate Education in STEM) and IUSE (Improving Undergraduate STEM Education).

The Earth Viewed as a Deforming Polyhedron: Method and Results

NASA Technical Reports Server (NTRS)

Blewitt, G.; Heflin, M. B.; Vigue, Y.; Zumberge, J. F.; Jefferson, D.; Webb, F. H.

1993-01-01

GPS is quite unlike any other geodetic technique, because we can use it to look at the Earth with high spatial and temporal resolution. For example, the GPS global network provides us with a daily snapshot of the Earth, allowing us to look with high temporal resolution at the motion of sites before, during, and after a large earthquake.The main focus of this paper is to view the Earth as an evolving polyhedron, whose vertices are defined by the GPS sites.

Preliminary study of GPS orbit determination accuracy achievable from worldwide tracking data

NASA Technical Reports Server (NTRS)

Larden, D. R.; Bender, P. L.

1983-01-01

The improvement in the orbit accuracy if high accuracy tracking data from a substantially larger number of ground stations is available was investigated. Observations from 20 ground stations indicate that 20 cm or better accuracy can be achieved for the horizontal coordinates of the GPS satellites. With this accuracy, the contribution to the error budget for determining 1000 km baselines by GPS geodetic receivers would be only about 1 cm. Previously announced in STAR as N83-14605

Program for Continued Development and Use of Ocean Acoustic/GPS Geodetic Techniques

NASA Technical Reports Server (NTRS)

Spiess, Fred N.

1997-01-01

Under prior NASA grants our group, with collaboration from scientists at the CalTech Jet Propulsion Lab (JPL), visualized and carried out the initial development of a combined GPS and underwater acoustic (GPS/A) method for determining the location of points on the deep sea floor with accuracy relevant to studies of crustal deformation. Under an immediately preceding grant we built, installed and surveyed a set of the necessary seafloor marker precision transponders just seaward of the Cascadia Subduction Zone off British Columbia. The JPL group carried out processing of the GPS data.

Observations of vertical tidal motions of a floating iceberg in front of Shirase Glacier, East Antarctica, using a geodetic-mode GPS buoy

NASA Astrophysics Data System (ADS)

Aoyama, Yuichi; Kim, Tae-Hee; Doi, Koichiro; Hayakawa, Hideaki; Higashi, Toshihiro; Ohsono, Shingo; Shibuya, Kazuo

2016-06-01

A dual-frequency GPS receiver was deployed on a floating iceberg downstream of the calving front of Shirase Glacier, East Antarctica, on 28 December 2011 for utilizing as floating buoy. The three-dimensional position of the buoy was obtained by GPS every 30 s with a 4-5-cm precision for ca. 25 days. The height uncertainty of the 1-h averaged vertical position was ∼0.5 cm, even considering the uncertainties of un-modeled ocean loading effects. The daily evolution of north-south (NS), east-west (EW), and up-down (UD) motions shows periodic UD variations sometimes attaining an amplitude of 1 m. Observed amplitudes of tidal harmonics of major constituents were 88%-93% (O1) and 85%-88% (M2) of values observed in the global ocean tide models FES2004 and TPXO-8 Atlas. The basal melting rate of the iceberg is estimated to be ∼0.6 m/day, based on a firn densification model and using a quasi-linear sinking rate of the iceberg surface. The 30-s sampling frequency geodetic-mode GPS buoy helps to reveal ice-ocean dynamics around the calving front of Antarctic glaciers.

An Autonomous, Low Cost Platform for Seafloor Geodetic Observations

NASA Astrophysics Data System (ADS)

Ericksen, T.; Foster, J. H.; Bingham, B. S.; Oshiro, J.

2014-12-01

The Pacific GPS Facility and the Field Robotics Laboratory at the University of Hawaii have developed an approach to significantly reduce costs below ship based methods of accurately measuring short-term vertical motions of the seafloor and maintaining a continuous long-term record of seafloor pressure. Our goal has been to reduce the primary barrier preventing us from acquiring the observations we need to understand geodetic processes, and the hazards they present, at subduction zones, submarine volcanoes, and subsea landslides. To this end, we have designed a payload package for one of the University of Hawaii Wave Gliders which incorporates an acoustic telemetry package, a dual frequency geodetic-grade Global Positioning System (GPS) receiver, meteorological sensors, processing computer, and cellular communications. The Wave Glider will interrogate high accuracy pressure sensors on the seafloor to maintain a near-continuous stream of pressure and temperature data. The seafloor geodetic monument seats a sensor capable of recording pressure, temperature, and sound velocity for a deployment duration of over 5 years with an acoustic modem for communications, and an integral acoustic release for recovery and replacement of batteries. The design of the geodetic monument allows for precise repositioning of the sensor to extend the pressure record beyond a single 5+ year deployment, and includes the capability to install a mobile pressure recorder for calibration of the linear drift of the continuous pressure sensor. We will present the design of the Wave Glider payload and seafloor geodetic monument, as well as a discussion of nearshore and offshore field tests and operational procedures. An assessment of our ability to determine cm-scale vertical seafloor motions will be made by integrating the seafloor pressure measurements recovered during field testing with independent measurements of sea surface pressure and sea surface height made by the sea surface payload.

Seismology and space-based geodesy

NASA Technical Reports Server (NTRS)

Tralli, David M.; Tajima, Fumiko

1993-01-01

The potential of space-based geodetic measurement of crustal deformation in the context of seismology is explored. The achievements of seismological source theory and data analyses, mechanical modeling of fault zone behavior, and advances in space-based geodesy are reviewed, with emphasis on realizable contributions of space-based geodetic measurements specifically to seismology. The fundamental relationships between crustal deformation associated with an earthquake and the geodetically observable data are summarized. The response and spatial and temporal resolution of the geodetic data necessary to understand deformation at various phases of the earthquake cycle is stressed. The use of VLBI, SLR, and GPS measurements for studying global geodynamics properties that can be investigated to some extent with seismic data is discussed. The potential contributions of continuously operating strain monitoring networks and globally distributed geodetic observatories to existing worldwide modern digital seismographic networks are evaluated in reference to mutually addressable problems in seismology, geophysics, and tectonics.

An Autonomous, Low Cost Platform for Seafloor Geodetic Observations

NASA Astrophysics Data System (ADS)

Ericksen, T.; Foster, J. H.; Bingham, B. S.

2013-12-01

The high cost of acquiring geodetic data from the sea floor has limited the observations available to help us understand and model the behavior of seafloor geodetic processes. To address this problem, the Pacific GPS Facility at the University of Hawaii is developing a cost effective approach for accurately measuring short-term vertical motions of the seafloor and maintaining a continuous long-term record of seafloor pressure without the requirement for costly ship time. There is a recognized need to vastly increase our underwater geodetic observing capacity. Most of the largest recorded earthquakes and most devastating tsunamis are generated at subduction zones underwater. Similarly, many volcanoes are partly (e.g. Santorini) or completely (e.g. Loihi) submerged, and are not well observed and understood. Furthermore, landslide features ring many ocean basins, and huge debris deposits surround many volcanic oceanic islands. Our approach will lower the cost of collecting sea-floor geodetic data, reducing the barriers preventing us from acquiring the information we need to observe and understand these types of structures and provide a direct societal benefit in improving hazard assessment. The capability is being developed by equipping one of the University of Hawaii Wave Gliders with an integrated acoustic telemetry package, a dual frequency geodetic-grade Global Positioning System (GPS) receiver, processing unit, and cellular communications. The Wave Glider will interrogate high accuracy pressure sensors on the sea floor to maintain a near-continuous stream of pressure and temperature data, but seafloor pressure data includes contribution from a variety of sources and on its own may not provide the accuracy required for geodetic investigations. Independent measurements of sea surface pressure and sea surface height can be used to remove these contributions from the observed sea floor pressure timeseries. We will integrate our seafloor pressure measurements with air pressure data, and precise vertical measurements of the sea surface from kinematic positioning of the Wave Glider over the bottom sensor, to determine cm-scale vertical seafloor motions. The seafloor package will consist of a simple tripod frame that seats the pressure sensor unit, and includes an attachment onto which an ROV can install a mobile pressure recorder (MPR) should ship and ROV time be available. Two visits with an MPR would allow calibration of the linear drift of the continuous sensor, further enhancing the value of the timeseries. The pressure sensor is recoverable and serviceable and using the MPR calibration will enable the seafloor monument to be re-occupied to extend the pressure record beyond a single 5+ year deployment. We are currently focused on retrieving high accuracy vertical sea floor motions, but, importantly, we have chosen a development approach that provides a simple upgrade path for incorporating the Wave Glider GPS-Acoustic (GPS/A) measurement system under development at SIO. With this upgrade, Wave Gliders could also acquire accurate horizontal motions of the sea floor sensors, and provide a cost-effective way of performing full, 3-dimensional, surveys of sea-floor motions.

Observation model and parameter partials for the JPL geodetic GPS modeling software GPSOMC

NASA Technical Reports Server (NTRS)

Sovers, O. J.; Border, J. S.

1988-01-01

The physical models employed in GPSOMC and the modeling module of the GIPSY software system developed at JPL for analysis of geodetic Global Positioning Satellite (GPS) measurements are described. Details of the various contributions to range and phase observables are given, as well as the partial derivatives of the observed quantities with respect to model parameters. A glossary of parameters is provided to enable persons doing data analysis to identify quantities in the current report with their counterparts in the computer programs. There are no basic model revisions, with the exceptions of an improved ocean loading model and some new options for handling clock parametrization. Such misprints as were discovered were corrected. Further revisions include modeling improvements and assurances that the model description is in accord with the current software.

Review of current GPS methodologies for producing accurate time series and their error sources

NASA Astrophysics Data System (ADS)

He, Xiaoxing; Montillet, Jean-Philippe; Fernandes, Rui; Bos, Machiel; Yu, Kegen; Hua, Xianghong; Jiang, Weiping

2017-05-01

The Global Positioning System (GPS) is an important tool to observe and model geodynamic processes such as plate tectonics and post-glacial rebound. In the last three decades, GPS has seen tremendous advances in the precision of the measurements, which allow researchers to study geophysical signals through a careful analysis of daily time series of GPS receiver coordinates. However, the GPS observations contain errors and the time series can be described as the sum of a real signal and noise. The signal itself can again be divided into station displacements due to geophysical causes and to disturbing factors. Examples of the latter are errors in the realization and stability of the reference frame and corrections due to ionospheric and tropospheric delays and GPS satellite orbit errors. There is an increasing demand on detecting millimeter to sub-millimeter level ground displacement signals in order to further understand regional scale geodetic phenomena hence requiring further improvements in the sensitivity of the GPS solutions. This paper provides a review spanning over 25 years of advances in processing strategies, error mitigation methods and noise modeling for the processing and analysis of GPS daily position time series. The processing of the observations is described step-by-step and mainly with three different strategies in order to explain the weaknesses and strengths of the existing methodologies. In particular, we focus on the choice of the stochastic model in the GPS time series, which directly affects the estimation of the functional model including, for example, tectonic rates, seasonal signals and co-seismic offsets. Moreover, the geodetic community continues to develop computational methods to fully automatize all phases from analysis of GPS time series. This idea is greatly motivated by the large number of GPS receivers installed around the world for diverse applications ranging from surveying small deformations of civil engineering structures (e.g., subsidence of the highway bridge) to the detection of particular geophysical signals.

Comparison of GPS and GRACE hydrological loading signatures in Myanmar, India, Bangladesh, and Bhutan

NASA Astrophysics Data System (ADS)

Materna, K.; Feng, L.; Lindsey, E. O.; Hill, E.; Burgmann, R.

2017-12-01

The elastic response of the lithosphere to surface mass redistributions produces significant deformation that can be observed in geodetic time series. This deformation is especially pronounced in Southeast Asia, where the annual monsoon produces large-amplitude hydrological loads. The MIBB network of 20 continuous GPS stations in Myanmar, India, Bangladesh, and Bhutan, operational since 2012, provides an opportunity to study the earth's response to these loads. In this study, we use GRACE gravity products as an estimate of surface water distribution, and input these estimates into an elastic loading calculation. We compare the predicted deformation with that observed with GPS. We find that elastic loading from the GRACE gravity field is able to explain the phase and the peak-to-peak amplitude (typically 2-3 cm) of the vertical GPS oscillations in northeast India and central Myanmar. GRACE-based corrections reduce the RMS scatter of the GPS data by 30%-45% in these regions. However, this approach does not capture all of the variation in central Bangladesh and southern Myanmar. Local hydrological effects, non-tidal ocean loads, poroelastic deformation, or differences in elastic properties may explain discrepancies between the GPS and GRACE signals in these places. The results of our calculations have practical implications for campaign GPS measurements in Myanmar, which make up the majority of geodetic measurements at this point. We may be able to reduce errors in campaign measurements and increase the accuracy of velocity estimates by correcting for hydrologic signals with GRACE data. The results also have potential implications for crustal rheology in Southeast Asia.

A demonstration of high precision GPS orbit determination for geodetic applications

NASA Technical Reports Server (NTRS)

Lichten, S. M.; Border, J. S.

1987-01-01

High precision orbit determination of Global Positioning System (GPS) satellites is a key requirement for GPS-based precise geodetic measurements and precise low-earth orbiter tracking, currently under study at JPL. Different strategies for orbit determination have been explored at JPL with data from a 1985 GPS field experiment. The most successful strategy uses multi-day arcs for orbit determination and includes fine tuning of spacecraft solar pressure coefficients and station zenith tropospheric delays using the GPS data. Average rms orbit repeatability values for 5 of the GPS satellites are 1.0, 1.2, and 1.7 m in altitude, cross-track, and down-track componenets when two independent 5-day fits are compared. Orbit predictions up to 24 hours outside the multi-day arcs agree within 4 m of independent solutions obtained with well tracked satellites in the prediction interval. Baseline repeatability improves with multi-day as compared to single-day arc orbit solutions. When tropospheric delay fluctuations are modeled with process noise, significant additional improvement in baseline repeatability is achieved. For a 246-km baseline, with 6-day arc solutions for GPS orbits, baseline repeatability is 2 parts in 100 million (0.4-0.6 cm) for east, north, and length components and 8 parts in 100 million for the vertical component. For 1314 and 1509 km baselines with the same orbits, baseline repeatability is 2 parts in 100 million for the north components (2-3 cm) and 4 parts in 100 million or better for east, length, and vertical components.

The UNAVCO role in planning, building, and maintaining geodetic infrastructure across the Americas: update on PBO, COCONet, and TLALOCNet

NASA Astrophysics Data System (ADS)

Mattioli, G. S.; Braun, J. J.; Cabral, E.; Calais, E.; DeMets, C.; Feaux, K.; Mencin, D.; Miller, M. M.; Normandeau, J.; Serra, Y.; Wang, G.

2013-05-01

UNAVCO maintains the NSF-funded Plate Boundary Observatory (PBO), which is the geodetic facility of EarthScope. PBO is largest continuous GPS and borehole geophysical network in the Americas, with ~1130 cGPS sites, including several with multiple monuments, ~80 boreholes, with 75 tensor strainmeters, 79 short-period, 3-component seismometers, and pore pressure sensors at 23 sites. PBO also includes 26 tiltmeters deployed at several volcanoes. Surface meteorological sensors are collocated at 134 GPS sites. UNAVCO provides high-rate (1 Hz), low-latency (<1 s) GPS data streams (RT-GPS) from 348 stations in PBO and has delivered over 62 Tb of geodetic data since PBO's inception in 2004. COCONet is a multi-hazard GPS-Met observatory, which extends PBO infrastructure into the Caribbean basin. In 2010, UNAVCO in collaboration with UCAR, was funded by NSF to build and initially maintain a network of 50 new cGPS/Met sites and incorporate another 50 existing sites in the Caribbean region. The revised siting plan calls for 46 new, 21 refurbished, and 77 existing stations spanning 26 nations in the Caribbean. Data from COCONet sites flow into the UNAVCO archive and are processed by the PBO analysis centers. Three workshops have helped to foster a COCONet science community and provide important guidance to UNAVCO to assure success of this complex multi-national project. A new joint UNAVCO-Mexican multi-hazard GPS-Met observatory, called TLALOCNet, has been proposed based on the outcomes of a NSF-funded workshop held in Puerto Vallarta in 2010. The TLALOCNet plan calls for UNAVCO to install 9 new PBO-quality GPS-Met sites in Mexico and adjacent islands, upgrade 29 sites previously installed with NSF funding along the western subduction boundary, and coordinate with the Mexican National Meteorological Service to federate data from at least another 80 GPS-Met sites distributed across Mexico. All GPS-Met data from TLALOCNet will be freely available at the UNAVCO archive and Mexican mirror sites. The ultimate goal for these networks is to provide free, high-quality, low-latency data and data products for researchers, educators, students, and the private sector. Data from COCONet and TLALOCNet will be used by US and international scientists to study solid earth processes, for example plate kinematics and dynamic as well as plate boundary interactions and deformation, with an emphasis on the earthquake cycle. The networks also serve atmospheric science objectives by providing more precise estimates of tropospheric water vapor thus enabling better forecast of the dynamics of airborne moisture associated with the yearly Caribbean hurricane cycle.

Geodetic slip rate estimates for the Alhama de Murcia and Carboneras faults in the SE Betics, Spain

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Echeverria, Anna; Masana, Eulàlia

2016-04-01

The Alhama de Murcia and the Carboneras faults are the most prominent geologic structures within the Eastern Betic Shear Zone (EBSZ), located in SE Spain. Using continuous and campaign GPS observations conducted during the last decade, we were able to confirm the continuing tectonic activity of these faults by quantifying their geodetic slip-rates and comparing the estimated values with the geological (including paleoseismological) observations. We find that the bulk of the observed deformation is concentrated around the Alhama de Murcia (AMF) and the Palomares (PF) faults. The geodetic horizontal slip rate (reverse-sinistral) of 1.5±0.3 mm/yr calculated for the AMF and PF fault system is in good agreement with geological observations at the AMF, as well as, the focal mechanism of the 2011 Lorca earthquake, suggesting a main role of the AMF. We also find that the geodetic slip rate of the Carboneras fault zone (CFZ) is almost purely sinistral strike-slip with a rate of 1.3±0.2 mm/yr along N48° direction, very similar to 1.1 mm/yr geologic slip-rate, estimated from recent onshore and offshore paleoseismic and geomorphologic studies. The fact the geodetic and the geologic slip-rates are similar at the AMF and CF faults, suggests that both faults have been tectonically active since Quaternary, slipping at approximately at constant rate of 1.1 to 1.8 mm/yr. Since the existing GPS data cannot discern whether the CFZ is slipping seismically or aseismically, we have intended to relate the on-going seismic activity to the slip-rates estimated using GPS. For this reason we compared seismic and geodetic strain rates, where the latter are larger than seismic strain rates, suggesting the presence of aseismic processes in the area. Nevertheless, due to the large earthquake recurrence intervals, we may be underestimating the seismic strain rates. The direction of the P and T average stress axes are in good agreement with geodetic principal strain rate axes. To summarize, in eastern Betics, Alhama de Murcia and Carboneras left-lateral faults are the most active faults and they play an important role in the regional plate convergence kinematics. The work has been supported by the Spanish Ministry of Science and Innovation projects: SHAKE (CGL2011-30005-C02-01), CHARMA (CGL2013-40828-R) and EVENT (CGL2006-12861-C02-01).

One nanosecond time synchronization using series and GPS

NASA Technical Reports Server (NTRS)

Buennagel, A. A.; Spitzmesser, D. J.; Young, L. E.

1983-01-01

Subnanosecond time sychronization between two remote rubidium frequency standards is verified by a traveling clock comparison. Using a novel, code ignorant Global Positioning System (GPS) receiver developed at JPL, the SERIES geodetic baseline measurement system is applied to establish the offset between the 1 Hz. outputs of the remote standards. Results of the two intercomparison experiments to date are presented as well as experimental details.

Accuracy assessment of Precise Point Positioning with multi-constellation GNSS data under ionospheric scintillation effects

NASA Astrophysics Data System (ADS)

Marques, Haroldo Antonio; Marques, Heloísa Alves Silva; Aquino, Marcio; Veettil, Sreeja Vadakke; Monico, João Francisco Galera

2018-02-01

GPS and GLONASS are currently the Global Navigation Satellite Systems (GNSS) with full operational capacity. The integration of GPS, GLONASS and future GNSS constellations can provide better accuracy and more reliability in geodetic positioning, in particular for kinematic Precise Point Positioning (PPP), where the satellite geometry is considered a limiting factor to achieve centimeter accuracy. The satellite geometry can change suddenly in kinematic positioning in urban areas or under conditions of strong atmospheric effects such as for instance ionospheric scintillation that may degrade satellite signal quality, causing cycle slips and even loss of lock. Scintillation is caused by small scale irregularities in the ionosphere and is characterized by rapid changes in amplitude and phase of the signal, which are more severe in equatorial and high latitudes geomagnetic regions. In this work, geodetic positioning through the PPP method was evaluated with integrated GPS and GLONASS data collected in the equatorial region under varied scintillation conditions. The GNSS data were processed in kinematic PPP mode and the analyses show accuracy improvements of up to 60% under conditions of strong scintillation when using multi-constellation data instead of GPS data alone. The concepts and analyses related to the ionospheric scintillation effects, the mathematical model involved in PPP with GPS and GLONASS data integration as well as accuracy assessment with data collected under ionospheric scintillation effects are presented.

Estimating Integrated Water Vapor (IWV) regional map distribution using METEOSAT satellite data and GPS Zenith Wet Delay (ZWD)

NASA Astrophysics Data System (ADS)

Reuveni, Y.; Leontiev, A.

2016-12-01

Using GPS satellites signals, we can study atmospheric processes and coupling mechanisms, which can help us understand the physical conditions in the upper atmosphere that might lead or act as proxies for severe weather events such as extreme storms and flooding. GPS signals received by geodetic stations on the ground are multi-purpose and can also provide estimates of tropospheric zenith delays, which can be converted into mm-accuracy Precipitable Water Vapor (PWV) using collocated pressure and temperature measurements on the ground. Here, we present the use of Israel's geodetic GPS receivers network for extracting tropospheric zenith path delays combined with near Real Time (RT) METEOSAT-10 Water Vapor (WV) and surface temperature pixel intensity values (7.3 and 12.1 channels, respectively) in order to obtain absolute IWV (kg/m2) or PWV (mm) map distribution. The results show good agreement between the absolute values obtained from our triangulation strategy based solely on GPS Zenith Total Delays (ZTD) and METEOSAT-10 surface temperature data compared with available radiosonde Precipitable IWV/PWV absolute values. The presented strategy can provide unprecedented temporal and special IWV/PWV distribution, which is needed as part of the accurate and comprehensive initial conditions pro­vided by upper-air observation systems at temporal and spatial resolutions consistent with the models assimilating them.

Kinematics and Seismotectonics of the Montello Thrust Fault (Southeastern Alps, Italy) Revealed by Local GPS and Seismic Networks

NASA Astrophysics Data System (ADS)

Serpelloni, E.; Anderlini, L.; Cavaliere, A.; Danesi, S.; Pondrelli, S.; Salimbeni, S.; Danecek, P.; Massa, M.; Lovati, S.

2014-12-01

The southern Alps fold-and-thrust belt (FTB) in northern Italy is a tectonically active area accommodating large part of the ~N-S Adria-Eurasia plate convergence, that in the southeastern Alps ranges from 1.5 to 2.5 mm/yr, as constrained by a geodetically defined rotation pole. Because of the high seismic hazard of northeastern Italy, the area is well monitored at a regional scale by seismic and GPS networks. However, more localized seismotectonic and kinematic features, at the scale of the fault segments, are not yet resolved, limiting our knowledge about the seismic potential of the different fault segments belonging to the southeastern Alps FTB. Here we present the results obtained from the analysis of data collected during local seismic and geodetic experiments conducted installing denser geophysical networks across the Montello-Bassano-Belluno system, a segment of the FTB that is presently characterized by a lower sismicity rate with respect to the surrounding domains. The Montello anticline, which is the southernmost tectonic features of the southeastern Alps FTB (located ~15 km south of the mountain front), is a nice example of growing anticline associated with a blind thrust fault. However, how the Adria-Alps convergence is partitioned across the FTB and the seismic potential of the Montello thrust (the area has been struck by a Mw~6.5 in 1695 but the causative fault is still largely debated) remained still unresolved. The new, denser, GPS data show that this area is undergoing among the highest geodetic deformation rates of the entire south Alpine chain, with a steep velocity gradient across the Montello anticline. The earthquakes recorded during the experiment, precisely relocated with double difference methods, and the new earthquake focal mechanisms well correlate with available information about sub-surface geological structures and highlight the seismotectonic activity of the Montello thrust fault. We model the GPS velocities using elastic dislocations embedded in a kinematic block model approach, which suggest that the Montello thrust fault is weakly coupled with respect to surrounding segments of the southernmost thrust system. Future works will include the integration of InSAR data and the densification/improvement of the geodetic infrastructure.

Strain accumulation across the Coast Ranges at the latitude of San Francisco, 1994-2000

USGS Publications Warehouse

Savage, J.C.; Gan, Weijun; Prescott, W.H.; Svarc, J.L.

2004-01-01

A 66-monument geodetic array spanning the Coast Ranges near San Francisco has been surveyed more than eight times by GIPS between late 1993 and early 2001. The measured horizontal velocities of the monuments are well represented by uniform, right-lateral, simple shear parallel to N29??W. (The local strike of the San Andreas Fault is ???N34??W. The observed areal dilatation rate of 6.9 ?? 10.0 nstrain yr-1 (quoted uncertainty is one standard deviation and extension is reckoned positive) is not significantly different from zero, which implies that the observed strain accumulation could be released by strike-slip faulting alone. Our results are consistent with the slip rates assigned by the Working Group on California Earthquake Probabilities [2003] to the principal faults (San Gregorio, San Andreas, Hayward-Rodgers Creek, Calaveras-Concord-Green Valley, and Greenville Faults) cutting across the GPS array. The vector sum of those slip rates is 39.8 ?? 2.6 mm yr-1 N29.8??W ?? 2.8??, whereas the motion across the GPS array (breadth 120 km) inferred from the uniform strain rate approximation is 38.7 ?? 1.2 mm yr-1 N29.0?? ?? 0.9?? right-lateral shear and 0.4 ?? 0.9 mm yr-1 N61??E ?? 0.9?? extension. We interpret the near coincidence of these rates and the absence of significant accumulation of areal dilatation to imply that right-lateral slip on the principal faults can release the accumulating strain; major strain release on reverse faults subparallel to the San Andreas Fault within the Coast Ranges is not required. Copyright 2004 by the American Geophysical union.

Precise GPS ephemerides from DMA and NGS tested by time transfer

NASA Technical Reports Server (NTRS)

Lewandowski, Wlodzimierz W.; Petit, Gerard; Thomas, Claudine

1992-01-01

It was shown that the use of the Defense Mapping Agency's (DMA) precise ephemerides brings a significant improvement to the accuracy of GPS time transfer. At present a new set of precise ephemerides produced by the National Geodetic Survey (NGS) has been made available to the timing community. This study demonstrates that both types of precise ephemerides improve long-distance GPS time transfer and remove the effects of Selective Availability (SA) degradation of broadcast ephemerides. The issue of overcoming SA is also discussed in terms of the routine availability of precise ephemerides.

GeoNetGIS: a Geodetic Network Geographical Information System to manage GPS networks in seismic and volcanic areas

NASA Astrophysics Data System (ADS)

Cristofoletti, P.; Esposito, A.; Anzidei, M.

2003-04-01

This paper presents the methodologies and issues involved in the use of GIS techniques to manage geodetic information derived from networks in seismic and volcanic areas. Organization and manipulation of different geodetical, geological and seismic database, give us a new challenge in interpretation of information that has several dimensions, including spatial and temporal variations, also the flexibility and brand range of tools available in GeoNetGIS, make it an attractive platform for earthquake risk assessment. During the last decade the use of geodetic networks based on the Global Positioning System, devoted to geophysical applications, especially for crustal deformation monitoring in seismic and volcanic areas, increased dramatically. The large amount of data provided by these networks, combined with different and independent observations, such as epicentre distribution of recent and historical earthquakes, geological and structural data, photo interpretation of aerial and satellite images, can aid for the detection and parameterization of seismogenic sources. In particular we applied our geodetic oriented GIS to a new GPS network recently set up and surveyed in the Central Apennine region: the CA-GeoNet. GeoNetGIS is designed to analyze in three and four dimensions GPS sources and to improve crustal deformation analysis and interpretation related with tectonic structures and seismicity. It manages many database (DBMS) consisting of different classes, such as Geodesy, Topography, Seismicity, Geology, Geography and Raster Images, administrated according to Thematic Layers. GeoNetGIS represents a powerful research tool allowing to join the analysis of all data layers to integrate the different data base which aid for the identification of the activity of known faults or structures and suggesting the new evidences of active tectonics. A new approach to data integration given by GeoNetGIS capabilities, allow us to create and deliver a wide range of maps, digital and 3-dimensional environment data analysis applications for geophysical users and civil defense companies, also distributing them on the World Wide Web or in wireless connection realized by PDA computer. It runs on powerful PC platform under Win2000 Prof OS © and based on ArcGIS 8.2 ESRI © software.

Geodetic Slip Solution for the Mw=7.4 Champerico (Guatemala) Earthquake of 07 November 2012

NASA Astrophysics Data System (ADS)

Ellis, A. P.; DeMets, C.; Briole, P.; Molina, E.; Flores, O.; Rivera, J.; Lasserre, C.; Lyon-Caen, H.; Lord, N. E.

2014-12-01

As the first large subduction thrust earthquake off the coast of western Guatemala in the past several decades, the 07 November 2012 Mw=7.4 earthquake offers the first opportunity for a geodetic study of coseismic and postseismic behavior for a segment of the Middle America trench where frictional coupling makes a transition from weak coupling off the coast of El Salvador to strong coupling in southern Mexico. We use measurements at 19 continuous GPS sites in Guatemala, El Salvador, and Mexico to estimate the coseismic slip and post-seismic deformation of the November 2012 Champerico (Guatemala) earthquake. Coseismic offsets range from ~47 mm near the epicenter to <1 mm at far-field sites in El Salvador. An inversion of the geodetic data indicate that that up to ~2 m of coseismic slip occurred on a ~30 km by 30 km rupture area between ~10 and 30 km depth, encouragingly close to the global CMT epicenter. The geodetic moment of 13 x 1019 N·m and corresponding magnitude of 7.4 both agree well with independent seismological estimates. An inversion for the postseismic fault afterslip shows that the transient postseismic motions recorded at 11 GPS sites are well fit with a logarithmically decaying function. More than 70 per cent of the postseismic slip occurred at the same depth or directly downdip from the main shock epicenter. At the upper limit, afterslip that occurred within 6 months of the earthquake released energy equivalent to only ~20 per cent of the coseismic moment. The seismologically derived slip solution from Ye et al. (2012), which features more highly concentrated slip than our own, fits our GPS offsets reasonably well provided that we translate their slip centroid ~51 km to the west to a position close to our own slip centroid. The geodetic and seismologic slip solutions thus suggest bounds of 2-5 m for the peak slip along a region of the interface no larger than 30 x 30 km and possibly much smaller.

Operational aspects of CASA UNO '88-The first large scale international GPS geodetic network

NASA Technical Reports Server (NTRS)

Neilan, Ruth E.; Dixon, T. H.; Meehan, Thomas K.; Melbourne, William G.; Scheid, John A.; Kellogg, J. N.; Stowell, J. L.

1989-01-01

For three weeks, from January 18 to February 5, 1988, scientists and engineers from 13 countries and 30 international agencies and institutions cooperated in the most extensive GPS (Global Positioning System) field campaign, and the largest geodynamics experiment, in the world to date. This collaborative eperiment concentrated GPS receivers in Central and South America. The predicted rates of motions are on the order of 5-10 cm/yr. Global coverage of GPS observations spanned 220 deg of longitude and 125 deg of latitude using a total of 43 GPS receivers. The experiment was the first civilian effort at implementing an extended international GPS satellite tracking network. Covariance analyses incorporating the extended tracking network predicted significant improvement in precise orbit determination, allowing accurate long-baseline geodesy in the science areas.

Assessing New GRAV-D Airborne Gravimetry Collected over the United States

NASA Astrophysics Data System (ADS)

Holmes, S. A.; Li, X.; Roman, D. R.

2013-12-01

The U.S. National Geodetic Survey [NGS], through their Gravity for the Redefinition of the American Vertical Datum [GRAV-D] program, is updating its terrestrial gravimetry holdings by flying new airborne gravity surveys over a large fraction of the USA and its territories. By 2020, NGS intends that all orthometric heights in the USA will be determined in the field by using a reliable national gravimetric geoid model to transform from geodetic heights obtained from GPS. Towards this end, the newly-collected airborne-gravimety is repeatedly evaluated by using it to support experimental gravitational models and gravimetric geoids, and then comparing these against independent data sets, such as ';satgrav' models (GRACE/GOCE), GPS/Leveling, astronomical vertical defections, and others. Here we show some results from these tests for GRAV-D airborne gravimetry collected over 2012/2013.

Coseismic deformation of the destructive April 6, 2009 L'Aquila earthquake (central Italy) from GPS data

NASA Astrophysics Data System (ADS)

Anzidei, M.; Boschi, E.; Cannelli, V.; Devoti, R.; Esposito, A.; Galvani, A.; Melini, D.; Pietrantonio, G.; Riguzzi, F.; Sepe, V.; Serpelloni, E.

2009-09-01

On April 6, 2009, 01:32:39 GMT, the city of L'Aquila was struck by a Mw 6.3 earthquake that killed 307 people, causing severe destruction and ground cracks in a wide area around the epicenter. Four days before the main shock we augmented the existing permanent GPS network with five GPS stations of the Central Apennine Geodetic Network (CaGeoNet) bordering the L'Aquila basin. The maximum horizontal and vertical coseismic surface displacements detected at these stations was 10.39 ± 0.45 cm and -15.64 ± 1.55 cm, respectively. Fixing the strike direction according to focal mechanism estimates, we estimated the source geometry with a non linear inversion of the geodetic data. Our best fitting fault model is a 13 × 15.7 km2 rectangular fault, SW-dipping at 55.3 ± 1.8°, consistent with the position of observed surface ruptures. The estimated slip (495 ± 29 mm) corresponds to a 6.3 moment magnitude, in excellent agreement with seismological data.

The contribution of engineering surveys by means of GPS to the determination of crustal movements in Istanbul

NASA Astrophysics Data System (ADS)

Özyaşar, M.; Özlüdemir, M. T.

2011-06-01

Global Navigation Satellite Systems (GNSS) are space based positioning techniques and widely used in geodetic applications. Geodetic networking accomplished by engineering surveys constitutes one of these tasks. Geodetic networks are used as the base of all kinds of geodetic implementations, Co from the cadastral plans to the relevant surveying processes during the realization of engineering applications. Geodetic networks consist of control points positioned in a defined reference frame. In fact, such positional information could be useful for other studies as well. One of such fields is geodynamic studies that use the changes of positions of control stations within a network in a certain time period to understand the characteristics of tectonic movements. In Turkey, which is located in tectonically active zones and struck by major earthquakes quite frequently, the positional information obtained in engineering surveys could be very useful for earthquake related studies. For this purpose, a GPS (Global Positioning System) network of 650 stations distributed over Istanbul (Istanbul GPS Triangulation Network; abbreviated IGNA) covering the northern part of the North Anatolian Fault Zone (NAFZ) was established in 1997 and measured in 1999. From 1998 to 2004, the IGNA network was extended to 1888 stations covering an area of about 6000 km2, the whole administration area of Istanbul. All 1888 stations within the IGNA network were remeasured in 2005. In these two campaigns there existed 452 common points, and between these two campaigns two major earthquakes took place, on 17 August and 12 November 1999 with a Richter scale magnitude of 7.4 and 7.2, respectively. Several studies conducted for estimating the horizontal and vertical displacements as a result of these earthquakes on NAFZ are discussed in this paper. In geodynamic projects carried out before the earthquakes in 1999, an annual average velocity of 2-2.5 cm for the stations along the NAFZ were estimated. Studies carried out using GPS observations in the same area after these earthquakes indicated that point displacements vary depending on their distance to the epicentres of the earthquakes. But the directions of point displacements are similar. The results obtained through the analysis of the IGNA network also show that there is a common trend in the directions of point displacements in the study area. In this paper, the past studies about the tectonics of Marmara region are summarised and the results of the displacement analysis on the IGNA network are discussed.

Investigation of land subsidence due to climate changes in surrounding areas of Urmia Lake (located in northwest of Iran) using wavelet coherence analysis of geodetic measurements and methodological data

NASA Astrophysics Data System (ADS)

Moghtased-Azar, K.; Mirzaei, A.; Nankali, H. R.; Tavakoli, F.

2012-04-01

Urmia Lake (salt lake in northwest of Iran) plays a valuable role in environment, wildlife and economy of Iran and the region, and now faces great challenges for survival. The Lake is in immediate and great danger and rapidly going to become salty desert. During the recent years and new heat wave, Iran, like many other countries are experiencing, is faced with relativity reduced rain fall. From a few years ago environment activists warned about potential dangers. Geodetic measurements, e.g., repeated leveling measurements of first order leveling network of Iran and continuous GPS measurements of Iranian Permanent GPS network of Iran (IPGN) showed that there is subsidence in surrounding areas of the lake. This paper investigates the relation between subsidence and climate changing in the area, using the wavelet coherence of the data of permanent GPS stations and daily methodological data. The results show that there is strong coherence between the subsidence phenomena induced by GPS data and climate warming from January 2009 up to end of August 2009. However, relative lake height variations computed from altimetry observations (TOPEX/POSEIDON (T/P), Jason-1 and Jason-2/OSTM) confirms maximum evaporation rates of the lake in this period.

GPS-based satellite tracking system for precise positioning

NASA Technical Reports Server (NTRS)

Yunck, T. P.; Melbourne, W. G.; Thornton, C. L.

1985-01-01

NASA is developing a Global Positioning System (GPS) based measurement system to provide precise determination of earth satellite orbits, geodetic baselines, ionospheric electron content, and clock offsets between worldwide tracking sites. The system will employ variations on the differential GPS observing technique and will use a network of nine fixed ground terminals. Satellite applications will require either a GPS flight receiver or an on-board GPS beacon. Operation of the system for all but satellite tracking will begin by 1988. The first major satellite application will be a demonstration of decimeter accuracy in determining the altitude of TOPEX in the early 1990's. By then the system is expected to yield long-baseline accuracies of a few centimeters and instantaneous time synchronization to 1 ns.

A Unified Geodetic Vertical Velocity Field (UGVVF), Version 1.0

NASA Astrophysics Data System (ADS)

Schmalzle, G.; Wdowinski, S.

2014-12-01

Tectonic motion, volcanic inflation or deflation, as well as oil, gas and water pumping can induce vertical motion. In southern California these signals are inter-mingled. In tectonics, properly identifying regions that are contaminated by other signals can be important when estimating fault slip rates. Until recently vertical deformation rates determined by high precision Global Positioning Systems (GPS) had large uncertainties compared to horizontal components and were rarely used to constrain tectonic models of fault motion. However, many continuously occupied GPS stations have been operating for ten or more years, often delivering uncertainties of ~1 mm/yr or less, providing better constraints for tectonic modeling. Various processing centers produced GPS time series and estimated vertical velocity fields, each with their own set of processing techniques and assumptions. We compare vertical velocity solutions estimated by seven data processing groups as well as two combined solutions (Figure 1). These groups include: Central Washington University (CWU) and New Mexico Institute of Technology (NMT), and their combined solution provided by the Plate Boundary Observatory (PBO) through the UNAVCO website. Also compared are the Jet Propulsion Laboratory (JPL) and Scripps Orbit and Permanent Array Center (SOPAC) and their combined solution provided as part of the NASA MEaSUREs project. Smaller velocity fields included are from Amos et al., 2014, processed at the Nevada Geodetic Laboratory, Shen et al., 2011, processed by UCLA and called the Crustal Motion Map 4.0 (CMM4) dataset, and a new velocity field provided by the University of Miami (UM). Our analysis includes estimating and correcting for systematic vertical velocity and uncertainty differences between groups. Our final product is a unified velocity field that contains the median values of the adjusted velocity fields and their uncertainties. This product will be periodically updated when new velocity fields become available. A database and scripts to access the database will be available through the University of Miami (http://www.geodesy.miami.edu) website. Figure 1. Vertical velocity comparisons between processing groups (blue dots). Red line indicates equal velocities. Weighted Root Mean Square (WRMS) is shown.

Broadband Array Analysis of the 2005 Episodic Tremor and Slip Event in Northern Cascadia

NASA Astrophysics Data System (ADS)

Wech, A.; Creager, K.; McCausland, W.; Frassetto, A.; Qamar, A.; Derosier, S.; Carmichael, J.; Malone, S.; Johnson, D.

2005-12-01

The region of Cascadia from the Olympic Mountains through southern Vancouver Island and down-dip of the subduction megathrust has repeatedly experienced episodes of slow slip. This episodic slip, which has been observed to take place over a period of two to several weeks, is accompanied by a seismic tremor signal. Based on the average recurrence interval of 14 months, the next episodic tremor and slip (ETS) event should occur within six weeks of mid-September, 2005. Indeed, it appears to have begun on September 3, as this abstract was being written. In order to record this anticipated event, we deployed an array of 11 three-component seismometers on the northern side of the Olympic Peninsula augmenting Pacific Northwest Seismographic Network stations as well as the first few EarthScope BigFoot stations and Plate Boundary Observatory borehole seismometers. This seismic array was comprised of six short-period and five broadband instruments with spacings of 500 m and 2200 m respectively. In conjunction with this Earthscope seismic deployment, we also installed a dense network of 29 temporary, continuous GPS stations across the entire Olympic Peninsula to integrate seismic and geodetic observations. One of the primary goals of this research is to utilize the broadband instrumentation in the array to investigate the possible correlation of low frequency energy with the rest of the tremor activity. ETS has been carefully investigated at high-frequency (seismic tremor at 2-6 Hz) and very low-frequency (slip occurring over weeks, observed by GPS). An important goal of this experiment is to investigate the possibility that the tremor generates intermediate, low-frequency signals. Preliminary analysis of short-period array recordings of the July, 2004 ETS event suggests that the tremor displays signs of lower-frequency energy (~0.5 Hz) correlated with its higher frequency activity. Our array should enable us to distinguish low- frequency signals originating in the direction of high-frequency tremor from noise in other directions. We will present an analysis of the low-frequency energy associated with this slip event.

An Introduction to the Tibet cGPS pilot project: TigiCAS

NASA Astrophysics Data System (ADS)

Zhang, Z.; Liu, J.; Galetzka, J.; Avouac, J.; Tapponnier, P.; Zeng, L.; Gan, W.; Shen, Z.; Wang, M.

2007-12-01

The convergence between India and Eurasia is the¡¡prototype of continental collision in action. Compared¡¡to geological history and fault kinematics studies, the present-day, regional pattern of strain-partitioning¡¡is still inadequately known. Among limited geodetic¡¡efforts in the past decade or two, most have been focused¡¡on refining measurements of the current crustal¡¡shortening rate across the Himalaya. The vast region¡¡immediately to the north is sparsely instrumented, with only one continuous GPS station (Lhasa) within¡¡the plateau proper. Campaign stations are few and¡¡ill-positioned, mostly along major roads, providing¡¡poor constraints on present-day slip-rates on individual¡¡active faults. The extant GPS network configuration is thus still insufficient to discriminate between block vs continuum deformation. In November 2006, the¡¡Chinese Academy of Sciences led a pilot program and¡¡installed 6 continuous GPS stations in southern Tibet, crossing the NS-trending normal fault systems and¡¡complementing the Nepal cGPS profiles. We present¡¡here the new sites, preliminary data processing results, and the spatial relationship with ongoing or planned¡¡continuous GPS sites from a couple of other projects. Together with such projects, TigiCAS will provide¡¡a substantial increase in geodetic data in the¡¡Himalayan-Tibet convergent belt in the next few¡¡years, and lead to a better understanding of¡¡contemporary deformation of the region.

Ppp Analisys with GPS and Glonass Integration in Periods Under Ionospheric Scintillation Effects

NASA Astrophysics Data System (ADS)

Marques, H. A. S.

2015-12-01

The GNSS is widely used nowadays either for geodetic positioning or scientific purposes. The GNSS currently includes GPS, GLONASS, Galileo among other emerging systems. The GPS and GLONASS are currently operational with a full satellite constellation. The GPS is still the most used nowadays and both GPS and GLONASS are under a modernization process. The geodetic positioning by using data from multi-constellation can provide better accuracy in positioning and also more reliability. The PPP is benefited once the satellite geometry is crucial in this method, mainly for kinematic scenarios. The satellite geometry can change suddenly for data collected in urban areas or in conditions of strong atmospheric effects such as Ionospheric Scintillation (IS) that causes weakening of signals with cycle slips and even loss of lock. The IS is caused by small irregularities in the ionosphere layer and is characterized by rapid change in amplitude and phase of the signal being stronger in equatorial and high latitudes regions. In this work the PPP is evaluated with GPS and GLONASS data collected by monitoring receivers from Brazilian CIGALA/CALIBRA network under IS conditions. The PPP processing was accomplished by using the GPSPPP software provided by Natural Resources Canadian (NRCAN). The IS effects were analyzed taking account the S4 and PHI60 indices. Considering periods with moderate IS effects, the use of only GPS data in the PPP presented several peaks in the coordinate time series due to cycle slips and loos of lock. In cycle slip conditions the ambiguity parameter are reinitialized by GPSPPP and considering loss of lock few satellites can be available in some epochs affecting the positioning geometry and consequently decreasing accuracy. In such situations, the PPP using GPS and GLONASS data presented improvements in positioning accuracy of the order to 70% in height component when compared with PPP using only GPS data. Analyses of GDOP and ambiguities parameters were also performed.

Feasibility of Construction of the Continuously Operating Geodetic GPS Network of Sinaloa, Mexico

NASA Astrophysics Data System (ADS)

Vazquez, G. E.; Jacobo, C.

2011-12-01

This research is based on the study and analysis of feasibility for the construction of the geodetic network for GPS continuous operation for Sinaloa, hereafter called (RGOCSIN). A GPS network of continuous operation is defined as that materialized structure physically through permanent monuments where measurements to the systems of Global Positioning (GPS) is performed continuously throughout a region. The GPS measurements in this network are measurements of accuracy according to international standards to define its coordinates, thus constituting the basic structure of geodetic referencing for a country. In this context is that in the near future the RGOCSIN constitutes a system state only accurate and reliable georeferencing in real-time (continuous and permanent operation) and will be used for different purposes; i.e., in addition to being fundamental basis for any lifting topographic or geodetic survey, and other areas such as: (1) Different construction processes (control and monitoring of engineering works); (2) Studies of deformation of the Earth's crust (before and after a seismic event); (3) GPS meteorology (weather forecasting); (4) Demarcation projects (natural and political); (5) Establishment of bases to generate mapping (necessary for the economic and social development of the state); (6) Precision agriculture (optimization of economic resources to the various crops); (7) Geographic information systems (Organization and planning activities associated with the design and construction of public services); (8) Urban growth (possible settlements in the appropriate form and taking care of the environmental aspect), among others. However there are criteria and regulations according to the INEGI (Instituto Nacional de Estadística y Geografía, http://www.inegi.org.mx/) that must be met; even for this stage of feasibility of construction that sees this project as a first phase. The fundamental criterion to be taken into account according to INEGI is a geometric distribution appropriate to ensure the state coverage, so the radius of coverage is found in the 10 to 15 Km. station. Likewise INEGI recommends the implementation of GPS measurements a priori in the vertices where at the end of such measurements generate a report by station containing details of the conditions of visibility, the GPS equipment used, the methodology of measurement and field data processing mode and is intended to build the RGOCSIN. Based on the results of the final report for each one of the measures beforehand, it will be or not feasible to determine if it meets these specifications to be finally considered as part of the RGOCSIN. It should be noted that the selection of the potential places where is intended to carry out the study and analysis of feasibility for the construction of the RGOCSIN will be some of the weather stations of the Centro de Investigación en Alimentación y Desarrollo (CIAD) Culiacán (http://www.ciad.edu.mx/clima/pc.asp). These weather stations have some technical infrastructure which would be used in the future; In addition to providing meteorological information which will ensure success in the solution of scientific and technological problems in various sectors requiring our state.

Use of Geodetic Surveys of Leveling Lines and Dry Tilt Arrays to Study Faults and Volcanoes in Undergraduate Field Geophysics Classes

NASA Astrophysics Data System (ADS)

Polet, J.; Alvarez, K.; Elizondo, K.

2017-12-01

In the early 1980's and 1990's numerous leveling lines and dry tilt arrays were installed throughout Central and Southern California by United States Geological Survey scientists and other researchers (e.g. Sylvester, 1985). These lines or triangular arrays of geodetic monuments commonly straddle faults or have been installed close to volcanic areas, where significant motion is expected over relatively short time periods. Over the past year, we have incorporated geodetic surveys of these arrays as part of our field exercises in undergraduate and graduate level classes on topics such as shallow subsurface geophysics and field geophysics. In some cases, the monuments themselves first had to be located based on only limited information, testing students' Brunton use and map reading skills. Monuments were then surveyed using total stations and global navigation satellite system (GNSS) receivers, using a variety of experimental procedures. The surveys were documented with tables, photos, maps and graphs in field reports, as well as in wiki pages created by student groups for a geophysics field class this June. The measurements were processed by the students and compared with similar data from surveys conducted soon after installation of the arrays, to analyze the deformation that occurred over the last few decades. The different geodetic techniques were also compared and an error analysis was conducted. The analysis and processing of these data challenged and enhanced students' quantitative literacy and technology skills. The final geodetic measurements are being incorporated into several senior and MSc thesis projects. Further surveys are planned for additional classes, in topics that could include seismology, geodesy, volcanology and global geophysics. We are also considering additional technologies, such as structure from motion (SfM) photogrammetry.

Implementation of Barcelona, L'estartit and Ibiza Sites for Altimeter Calibration

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J. J.; Gili, J.; Lopez, R.; Tapia, A.; Bosch, E.; Perez, B.; Pros, F.

2012-12-01

A marine campaign to compute the sea surface data along the Spanish Mediterranean coastline and Balearic Islands is being prepared for 2013. Jason-2 (period ~10 days) and Saral/AltiKa (period of 35 days and expected launch in 2012) altimetric data and on-board GPS data will be used. Many GPS Buoy sessions along the ship route will be performed.Sea height estimates (instantaneous and mean sea levels) will be compared. Recently some geodetic improvements has been made in specific coastal spanish sites in the NW Mediterranean Sea for monitoring sea level. The goal is to maintain and improve the quality of the observation of the sea level change in the three sites. The information is coming from Puertos del Estado www.puertos.es L'Estartit tide gauge has been co-located with geodetic techniques (GPS measurements of XU, Utilitary Network, and XdA, Levelling Network,) and it is tied to the SPGIC (Integrated Geodetic Positioning System of Catalonia) project of the Cartographic Institute of Catalunya (ICC). In the past three calibration campaigns for Topex/Poseidon and Jason-1 in March 1999, August 2000 and July 2002 near Cape of Begur. At Barcelona harbour there is one MIROS radar tide gauge belonging to Puertos del Estado (Spanish Harbours).The radar sensor is over the water surface, on a L-shaped structure which elevates it a few meters above the quay shelf. 1-min data are transmitted to the ENAGAS Control Center by cable and then sent each 1 min to Puertos del Estado by e-mail. The information includes wave forescast (mean period, significant wave height, sea level, etc.This sensor also measures agitation and sends wave parameters each 20 min. There is a GPS station Leica Geosystems GRX1200 GG Pro and antenna 1202. Bathymetric campaigns inside the harbour have been made. At Ibiza site new measurements and levelling between the GPS reference station and a Radar MIROS, both from Puertos del Estado, has been made recently. A calibration campaign for Jason-1 was made in June 2003 in the Ibiza area, main calibration site. The presentation is directed to the description of the actual situation of the geodetic infrastructure of Barcelona, l'Estartit sites for sea level determination and complementing Ibiza site for a new altimeter calibration campaign of Jason-2 and Saral/AltiKa satellites to be made in 2013. Specifications of the new marine calibration campaign will be presented.

Seismic and Geodetic Monitoring of the Nicoya, Costa Rica, Seismic Gap

NASA Astrophysics Data System (ADS)

Protti, M.; Gonzalez, V.; Schwartz, S.; Dixon, T.; Kato, T.; Kaneda, Y.; Simila, G.; Sampson, D.

2007-05-01

The Nicoya segment of the Middle America Trench has been recognized as a mature seismic gap with potential to generate a large earthquake in the near future (it ruptured with large earthquakes in 1853, 1900 and 1950). Low level of background seismicity and fast crustal deformation of the forearc are indicatives of strong coupling along the plate interface. Given its high seismic potential, the available data and especially the fact that the Nicoya peninsula extends over large part of the rupture area, this gap was selected as one of the two sites for a MARGINS-SEIZE experiment. With the goal of documenting the evolution of loading and stress release along this seismic gap, an international effort involving several institutions from Costa Rica, the United States and Japan is being carried out for over a decade in the region. This effort involves the installation of temporary and permanent seismic and geodetic networks. The seismic network includes short period, broad band and strong motion instruments. The seismic monitoring has provided valuable information on the geometry and characteristics of the plate interface. The geodetic network includes temporary and permanent GPS stations as well as surface and borehole tiltmeters. The geodetic networks have helped quantify the extend and degree of coupling. A continuously recording, three- station GPS network on the Nicoya Peninsula, Costa Rica, recorded what we believe is the first slow slip event observed along the plate interface of the Costa Rica subduction zone. We will present results from these monitoring networks. Collaborative international efforts are focused on expanding these seismic and geodetic networks to provide improved resolution of future creep events, to enhanced understanding of the mechanical behavior of the Nicoya subduction segment of the Middle American Trench and possibly capture the next large earthquake and its potential precursor deformation.

Geodetic insights on the post-seismic transients from the Andaman Nicobar region: 2005-2013

NASA Astrophysics Data System (ADS)

Earnest, A.; Vijayan, M.; Jade, S.; Krishnan, R.; Sringeri, S. T.

2013-12-01

The 2004 Mw 9.2 Sumatra-Andaman mega-thrust rupture broke the whole 1300 km long fore-arc sliver boundary of the Indo- Burmese collision. Earlier events of 1679 (M~7.5), 1941 (M 7.7), 1881 (M~7.9) and 2002 (Mw 7.3) generated spatially restricted ruptures along this margin. GPS based geodetic measurements of post-seismic deformation following the 2004 M9.2 Sumatra-Andaman earthquake gives insights on the spatio-temporal evolution of transient tectonic deformation happening at the Suda-Andaman margin. This work encompasses the near-field geodetic data collected from the Andaman-Nicobar Islands and far-field CGPS site data available from SUGAR, UNAVCO and IGS from 2005-2013. Precise geodetic data analysis shows that the GPS benchmarks in the Andaman-Nicobar region moved immediately after 2004 event towards the sea-ward trench in the SW direction, following very much the co-seismic offset directions. This can be possibly because of the continued predominant after-slip occurrence around the 2004 rupture zone due to the velocity-strengthening behavior at the downdip segments of the rupture zone. Lately a progressive reversal of motion direction away from the oceanic trench (and the co-seismic offset direction) of the coastal and inland GPS sites of Andaman-Nicobar Islands are observed. The site displacement transients shows a rotation of the displacement vector moving from south-west to north. Spatio-temporal analysis of the earthquakes show dense shallow seismicity in the back-arc region, normal and thrust faulting activity towards the trench. The hypo-central distribution highlights the shallow subduction at the northern segment, which becomes steeper and deeper to the south. The stress distribution, inferred from the P and T-axes of earthquake faulting mechanisms, represents the compressional fore-arc and extensional back-arc stress regimes. Our analysis results will be discussed in detail by integrating the kinematics and seismo-tectonic evolution of this subducting margin for the post-seismic period from 2005 - 2013.

New Developments in Geodetic Data Management Systems for Fostering International Collaborations in the Geosciences

NASA Astrophysics Data System (ADS)

Meertens, Charles; Boler, Fran; Miller, M. Meghan

2015-04-01

UNAVCO community investigators are actively engaged in using space and terrestrial geodetic techniques to study earthquake processes, mantle properties, active magmatic systems, plate tectonics, plate boundary zone deformation, intraplate deformation, glacial isostatic adjustment, and hydrologic and atmospheric processes. The first GPS field projects were conducted over thirty years ago, and from the beginning these science investigations and the UNAVCO constituency as a whole have been international and collaborative in scope and participation. Collaborations were driven by the nature of the scientific problems being addressed, the capability of the technology to make precise measurements over global scales, and inherent technical necessity for sharing of GPS tracking data across national boundaries. The International GNSS Service (IGS) was formed twenty years ago as a voluntary federation to share GPS data from now hundreds of locations around the globe to facilitate realization of global reference frames, ties to regional surveys, precise orbits, and to establish and improve best practices in analysis and infrastructure. Recently, however, numbers of regional stations have grown to the tens of thousands, often with data that are difficult to access. UNAVCO has been working to help remove technical barriers by providing open source tools such as the Geodetic Seamless Archive Centers software to facilitate cross-project data sharing and discovery and by developing Dataworks software to manage network data. Data web services also provide the framework for UNAVCO contributions to multi-technique, inter-disciplinary, and integrative activities such as CoopEUS, GEO Supersites, EarthScope, and EarthCube. Within the geodetic community, metadata standards and data exchange formats have been developed and evolved collaboratively through the efforts of global organizations such as the IGS. A new generation of metadata and data exchange formats, as well as the software tools that utilize these formats and that support more efficient exchange of the highest quality data and metadata, are currently being developed and deployed through multiple international efforts.

Reconciling geodetic and geologic slip rates along the Carboneras fault in the Betics: work in progress

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; López, Robert; Pallàs, Raimon; Bordonau, Jaume; Masana, Eulàlia

2017-04-01

As part of the recently initiated research project we are in the process of studying in detail the geodynamic behavior of the Carboneras fault in the SE Betics in Spain. Specifically, we plan to quantify the geodetic and geologic slip rates for the onland section of the fault, as well as getting some insight on the state of locking of the fault. As a result of our previous GPS observations, we have been able to illustrate the continuing tectonic activity of the Carboneras fault, expressed mainly as a left-lateral strike slip motion of 1.3±0.2 mm/yr (Echeverria et al., 2015). To reveal how the deformation is partitioned between different structures, 3 new continuous GPS points are being established along fault-perpendicular profile. In addition, since summer 2016, we have conducted surveys of the nearby CuaTeNeo and IGN Regente points. We have also established and measured several new geodetic points in the vicinity of the fault, with the aim of increasing the spatial coverage around it. The above-mentioned geodetic, short-term, slip rates are in surprisingly good agreement with the estimates of geologic slip rates based on paleoseismic studies, which indicate a minimum strike-slip rate of 1.31 mm/yr and a dip-slip rate of 0.05 mm/yr since 110.3 ka (Moreno et al. 2015). In order to increase the paleoseismic event database, 6 new sites have been identified along the fault, where further paleoseismic trenching surveys will be conducted within the coming years. These new data, combined with the findings of the recent geomorphological study of river offsets (Ferrater, 2016) and new GPS observations, should significantly improve the reliability of the existent deformation data and as a consequence, contribute to better understanding the seismic hazard posed by the Carbonears fault in the SE Betics. This work is funded by the project PREVENT (CGL2015-66263-R), financed by the Ministry of Economy, Industry and Competitiveness.

Integration of the Plate Boundary Observatory and Existing GPS Networks in Southern California: A Multi Use Geodetic Network

NASA Astrophysics Data System (ADS)

Walls, C.; Blume, F.; Meertens, C.; Arnitz, E.; Lawrence, S.; Miller, S.; Bradley, W.; Jackson, M.; Feaux, K.

2007-12-01

The ultra-stable GPS monument design developed by Southern California Geodetic Network (SCIGN) in the late 1990s demonstrates sub-millimeter errors on long time series where there are a high percentage of observations and low multipath. Following SCIGN, other networks such as PANGA and BARGEN have adopted the monument design for both deep drilled braced monuments (DDBM = 5 legs grouted 10.7 meters into bedrock/stratigraphy) and short drilled braced monuments (SDBM = 4 legs epoxied 2 meters into bedrock). A Plate Boundary Observatory (PBO) GPS station consists of a "SCIGN" style monument and state of the art NetRS receiver and IP based communications. Between the years 2003-2008 875 permanent PBO GPS stations are being built throughout the United States. Concomitant with construction of the PBO the majority of pre-existing GPS stations that meet stability specifications are being upgraded with Trimble NetRS and IP based communications to PBO standards under the EarthScope PBO Nucleus project. In 2008, with completed construction of the Plate Boundary Observatory, more than 1100 GPS stations will share common design specifications and have identical receivers with common communications making it the most homogenous geodetic network in the World. Of the 875 total Plate Boundary Observatory GPS stations, 211 proposed sites are distributed throughout the Southern California region. As of August 2007 the production status is: 174 stations built (81 short braced monuments, 93 deep drilled braced monuments), 181 permits signed, 211 permits submitted and 211 station reconnaissance reports. The balance of 37 stations (19 SDBM and 18 DDBM) will be built over the next year from Long Valley to the Mexico border in order of priority as recommended by the PBO Transform, Extension and Magmatic working groups. Fifteen second data is archived for each station and 1 Hz as well as 5 Hz data is buffered to be triggered for download in the event of an earthquake. Communications equipment includes CDMA Proxicast modems, Hughes Vsat, Intuicom 900 MHz Ethernet bridge radios and several "real-time" sites use 2.4 GHz Wilan radios. Ultimately, 125 of the existing former-SCIGN GPS stations will be integrated into the So Cal region of PBO, of which 25 have real-time data streams. At the time of this publication the total combined Southern California region has over 40 stations streaming real-time data using both radios and CDMA modems. The real-time GPS sites provide specific benefits beyond the standard GPS station: they can provide a live correction for local surveyors and can be used to trigger an alarm if large displacements are recorded. The cross fault spatial distribution of these 336 GPS stations in the seismically active southern California region has the grand potential of augmenting a strong motion earthquake early warning system.

Rifting mechanisms constrained by InSAR, seismicity, GPS, and surface rupture from the Karonga earthquake sequence in northern Lake Malawi (Nyasa)

NASA Astrophysics Data System (ADS)

Zheng, W.; Pritchard, M. E.; Henderson, S. T.; Gaherty, J. B.; Shillington, D. J.; Oliva, S. J.; Ebinger, C.; Nooner, S. L.; Elliott, J.; Saria, E.; Ntambila, D.; Chindandali, P. R. N.

2017-12-01

The Malawi rift is part of the archetypal East African rift where early-stage crustal extension is dominated by faulting. In the Karonga region of northern Malawi, a sequence of earthquakes in late 2009, with 15 teleseismically detected (Mw 4.5-6.0) over 13 days, provides a uniqueopportunity to evaluate faulting processes controlling present-day extension in an early-stage rift. We describe observations of this sequence including hundreds of aftershocks located by a temporary seismic array installed in 2010, ground deformation from satellite interferograms, and surface rupture from field surveys published by others. We use all of these data to model fault geometry and slip. The aftershocks from January-May 2010 suggest the involvement of multiple faults, and we test the extent that this can be resolved by the InSAR data. The InSAR and surface rupture both suggest that the major slip occurred at shallow depth (<5 km). Our preferred aftershock locations appear to correlate with this principal slip zone, although uncertainty in the shallow velocity structure can allow for a bulk of the events to fall down-dip of the geodetically constrained slip. Subsequent deformation, including that associated with a December 2014 Mw 5.1 earthquake, can be constrained from multidisciplinary data collected during the SEGMeNT (Study of Extension and maGmatism in Malawi aNd Tanzania) project, which includes the Karonga region and spans 2013-2015. We find 3 cm of potential ground movement at the location of the earthquake as determined by the SEGMeNT seismic array from Sentinel-1. Geodetic fault slip is consistent with the focal mechanism and depth determined by the local array. The location is at the northern end of the 2009-2010 aftershock zone, and aftershocks suggest some linkage with faults that slipped in 2009. InSAR observations do not provide any evidence for large aseismic slip or fluid movements during or after the 2014 sequence, which had <200 aftershocks above the network threshold. For example, we do not observe any deformation at Rungwe volcano above the 2 cm/yr detection threshold with InSAR time series from ALOS (2007-2010) or Sentinel-1 (10/2014 - 04/2017). The time series from SEGMeNT and other continuous GPS stations do not show transients related to the earthquakes, but are not optimally located in space or time.

A Comparison of Moment Rates for the Eastern Mediterranean Region from Competitive Kinematic Models

NASA Astrophysics Data System (ADS)

Klein, E. C.; Ozeren, M. S.; Shen-Tu, B.; Galgana, G. A.

2017-12-01

Relatively continuous, complex, and long-lived episodes of tectonic deformation gradually shaped the lithosphere of the eastern Mediterranean region into its present state. This large geodynamically interconnected and seismically active region absorbs, accumulates and transmits strains arising from stresses associated with: (1) steady northward convergence of the Arabian and African plates; (2) differences in lithospheric gravitational potential energy; and (3) basal tractions exerted by subduction along the Hellenic and Cyprus Arcs. Over the last twenty years, numerous kinematic models have been built using a variety of assumptions to take advantage of the extensive and dense GPS observations made across the entire region resulting in a far better characterization of the neotectonic deformation field than ever previously achieved. In this study, three separate horizontal strain rate field solutions obtained from three, region-wide, GPS only based kinematic models (i.e., a regional block model, a regional continuum model, and global continuum model) are utilized to estimate the distribution and uncertainty of geodetic moment rates within the eastern Mediterranean region. The geodetic moment rates from each model are also compared with seismic moment release rates gleaned from historic earthquake data. Moreover, kinematic styles of deformation derived from each of the modeled horizontal strain rate fields are examined for their degree of correlation with earthquake rupture styles defined by proximal centroid moment tensor solutions. This study suggests that significant differences in geodetically obtained moment rates from competitive kinematic models may introduce unforeseen bias into regularly updated, geodetically constrained, regional seismic hazard assessments.

An Autonomous, Low Cost Platform for Seafloor Geodetic Observations

NASA Astrophysics Data System (ADS)

Ericksen, T.; Foster, J. H.; Bingham, B. S.; Oshiro, J.

2015-12-01

The Pacific GPS Facility and the Field Robotics Laboratory at the University of Hawaii have developed an approach to significantly reduce the costs of accurately measuring short-term vertical motions of the seafloor and maintaining a continuous long-term record of seafloor pressure. Traditional ship-based methods of acquiring these measurements are often prohibitively expensive. Our goal has been to reduce the primary barrier preventing us from acquiring the observations we need to understand geodetic processes, and the hazards they present, at subduction zones, submarine volcanoes, and subsea landslides. To this end, we have designed a payload package for the University of Hawaii Wave Glider which incorporates an acoustic telemetry package, a dual frequency geodetic-grade Global Positioning System (GPS) receiver, meteorological sensors, processing computer, and cellular communications. The Wave Glider is able to interrogate high accuracy pressure sensors on the seafloor to maintain a near-continuous stream of ocean bottom pressure and temperature data. The Wave Glider also functions as an integral part of the seafloor geodetic observing system, recording accurate sea surface elevations and barometric pressure; direct measurements of two of the primary sources of seafloor pressure change. The seafloor geodetic monument seats a sensor capable of recording pressure, temperature, and sound velocity for a deployment duration of over 5 years with an acoustic modem for communications, and an integral acoustic release for recovery and replacement of batteries. The design of the geodetic monument allows for precise repositioning of the sensor to extend the pressure record beyond a single 5+ year deployment, and includes the capability to install a mobile pressure recorder for calibration of the linear drift of the continuous pressure sensor. We will present the results of our field tests and an assessment of our ability to determine cm-scale vertical seafloor motions by integrating our seafloor pressure measurements with the independent Wave Glider measurements of sea surface pressure and sea surface height. An overall summary of the performance and costs of making seafloor geodetic measurement with this system will be provided.

Present-day kinematics of the Danakil block (southern Red Sea-Afar) constrained by GPS

NASA Astrophysics Data System (ADS)

Ladron de Guevara, R.; Jonsson, S.; Ruch, J.; Doubre, C.; Reilinger, R. E.; Ogubazghi, G.; Floyd, M.; Vasyura-Bathke, H.

2017-12-01

The rifting of the Arabian plate from the Nubian and Somalian plates is primarily accommodated by seismic and magmatic activity along two rift arms of the Afar triple junction (the Red Sea and Gulf of Aden rifts). The spatial distribution of active deformation in the Afar region have been constrained with geodetic observations. However, the plate boundary configuration in which this deformation occurs is still not fully understood. South of 17°N, the Red Sea rift is composed of two parallel and overlapping rift branches separated by the Danakil block. The distribution of the extension across these two overlapping rifts, their potential connection through a transform fault zone and the counterclockwise rotation of the Danakil block have not yet been fully resolved. Here we analyze new GPS observations from the Danakil block, the Gulf of Zula area (Eritrea) and Afar (Ethiopia) together with previous geodetic survey data to better constrain the plate kinematics and active deformation of the region. The new data has been collected in 2016 and add up to 5 years to the existing geodetic observations (going back to 2000). Our improved GPS velocity field shows differences with previously modeled GPS velocities, suggesting that the rate and rotation of the Danakil block need to be updated. The new velocity field also shows that the plate-boundary strain is accommodated by broad deformation zones rather than across sharp boundaries between tectonic blocks. To better determine the spatial distribution of the strain, we first implement a rigid block model to constrain the overall regional plate kinematics and to isolate the plate-boundary deformation at the western boundary of the Danakil block. We then study whether the recent southern Red Sea rifting events have caused detectable changes in observed GPS velocities and if the observations can be used to constrain the scale of this offshore rift activity. Finally, we investigate different geometries of transform faults that might connect the two overlapping branches of the southern Red Sea rift in the Gulf of Zula region.

GPS Monitoring of Surface Change During and Following the Fortuitous Occurrence of the M(sub w) = 7.3 Landers Earthquake in our Network

NASA Technical Reports Server (NTRS)

Miller, M. Meghan

1998-01-01

Accomplishments: (1) Continues GPS monitoring of surface change during and following the fortuitous occurrence of the M(sub w) = 7.3 Landers earthquake in our network, in order to characterize earthquake dynamics and accelerated activity of related faults as far as 100's of kilometers along strike. (2) Integrates the geodetic constraints into consistent kinematic descriptions of the deformation field that can in turn be used to characterize the processes that drive geodynamics, including seismic cycle dynamics. In 1991, we installed and occupied a high precision GPS geodetic network to measure transform-related deformation that is partitioned from the Pacific - North America plate boundary northeastward through the Mojave Desert, via the Eastern California shear zone to the Walker Lane. The onset of the M(sub w) = 7.3 June 28, 1992, Landers, California, earthquake sequence within this network poses unique opportunities for continued monitoring of regional surface deformation related to the culmination of a major seismic cycle, characterization of the dynamic behavior of continental lithosphere during the seismic sequence, and post-seismic transient deformation. During the last year, we have reprocessed all three previous epochs for which JPL fiducial free point positioning products available and are queued for the remaining needed products, completed two field campaigns monitoring approx. 20 sites (October 1995 and September 1996), begun modeling by development of a finite element mesh based on network station locations, and developed manuscripts dealing with both the Landers-related transient deformation at the latitude of Lone Pine and the velocity field of the whole experiment. We are currently deploying a 1997 observation campaign (June 1997). We use GPS geodetic studies to characterize deformation in the Mojave Desert region and related structural domains to the north, and geophysical modeling of lithospheric behavior. The modeling is constrained by our existing and continued GPS measurements, which will provide much needed data on far-field strain accumulation across the region and on the deformational response of continental lithosphere during and following a large earthquake, forming the basis for kinematic and dynamic modeling of secular and seismic-cycle deformation. GPS geodesy affords both regional coverage and high precision that uniquely bear on these problems.

Development And Test of A Digitally Steered Antenna Array for The Navigator GPS Receiver

NASA Technical Reports Server (NTRS)

Pinto, Heitor David; Valdez, Jennifer E.; Winternitz, Luke M. B.; Hassouneh, Munther A.; Price, Samuel R.

2012-01-01

Global Positioning System (GPS)-based navigation has become common for low-Earth orbit spacecraft as the signal environment is similar to that on the Earth s surface. The situation changes abruptly, however, for spacecraft whose orbital altitudes exceed that of the GPS constellation. Visibility is dramatically reduced and signals that are present may be very weak and more susceptible to interference. GPS receivers effective at these altitudes require increased sensitivity, which often requires a high-gain antenna. Pointing such an antenna can pose a challenge. One efficient approach to mitigate these problems is the use of a digitally steered antenna array. Such an antenna can optimally allocate gain toward desired signal sources and away from interferers. This paper presents preliminary results in the development and test of a digitally steered antenna array for the Navigator GPS research program at NASA s Goddard Space Flight Center. In particular, this paper highlights the development of an array and front-end electronics, the development and test of a real-time software GPS receiver, and implementation of three beamforming methods for combining the signals from the array. Additionally, this paper discusses the development of a GPS signal simulator which produces digital samples of the GPS L1C/A signals as they would be received by an arbitrary antenna array configuration. The simulator models transmitter and receiver dynamics, near-far and multipath interference, and has been a critical component in both the development and test of the GPS receiver. The GPS receiver system was tested with real and simulated GPS signals. Preliminary results show that performance improvement was achieved in both the weak signal and interference environments, matching analytical predictions. This paper summarizes our initial findings and discusses the advantages and limitations of the antenna array and the various beamforming methods.

Portable global positioning system receivers: static validity and environmental conditions.

PubMed

Duncan, Scott; Stewart, Tom I; Oliver, Melody; Mavoa, Suzanne; MacRae, Deborah; Badland, Hannah M; Duncan, Mitch J

2013-02-01

GPS receivers are becoming increasingly common as an objective measure of spatiotemporal movement in free-living populations; however, research into the effects of the surrounding physical environment on the accuracy of off-the-shelf GPS receivers is limited. The goal of the current study was to (1) determine the static validity of seven portable GPS receiver models under diverse environmental conditions and (2) compare the battery life and signal acquisition times among the models. Seven GPS models (three units of each) were placed on six geodetic sites subject to a variety of environmental conditions (e.g., open sky, high-rise buildings) on three separate occasions. The observed signal acquisition time and battery life of each unit were compared to advertised specifications. Data were collected and analyzed in June 2012. Substantial variation in positional error was observed among the seven GPS models, ranging from 12.1 ± 19.6 m to 58.8 ± 393.2 m when averaged across the three test periods and six geodetic sites. Further, mean error varied considerably among sites: the lowest error occurred at the site under open sky (7.3 ± 27.7 m), with the highest error at the site situated between high-rise buildings (59.2 ± 99.2 m). While observed signal acquisition times were generally longer than advertised, the differences between observed and advertised battery life were less pronounced. Results indicate that portable GPS receivers are able to accurately monitor static spatial location in unobstructed but not obstructed conditions. It also was observed that signal acquisition times were generally underestimated in advertised specifications. Copyright © 2013 American Journal of Preventive Medicine. Published by Elsevier Inc. All rights reserved.

Uplift of the Western Transverse Ranges and Ventura Area of Southern California: A Four-Technique Geodetic Study Combining GPS, InSAR, Leveling, and Tide Gauges

NASA Astrophysics Data System (ADS)

Hammond, William C.; Burgette, Reed J.; Johnson, Kaj M.; Blewitt, Geoffrey

2018-01-01

We estimate the rate of vertical land motion (VLM) in the region around the Western Transverse Ranges (WTR), Ventura, and Big Bend of the San Andreas Fault (SAF) of southern California using data from four geodetic techniques: GPS, interferometric synthetic aperture radar (InSAR), leveling, and tide gauges. We use a new analysis technique called GPS Imaging to combine the techniques and leverage the synergy between (1) high geographic resolution of InSAR, (2) precision, stability, and geocentric reference frame of GPS, (3) decades long observation of VLM with respect to the sea surface from tide gauges, and (4) relative VLM along dense leveling lines. The uncertainty in the overall rate field is 1 mm/yr, though some individual techniques have uncertainties as small as 0.2 mm/yr. The most rapid signals are attributable to subsidence in aquifers and groundwater changes. Uplift of the WTR is geographically continuous, adjacent to the SAF and appears related to active crustal contraction across Pacific/North America plate boundary fault system. Uplift of the WTR and San Gabriel Mountains is 2 mm/yr and is asymmetrically focused west of the SAF, consistent with interseismic strain accumulation across thrust faults in the Ventura area and Santa Barbara channel that accommodate contraction against the near vertical SAF.

Plans for a Northern Cascadia Subduction Zone Observatory

NASA Astrophysics Data System (ADS)

Heesemann, M.; Wang, K.; Davis, E.; Chadwell, C. D.; Nissen, E.; Moran, K.; Scherwath, M.

2017-12-01

To accurately assess earthquake and tsunami hazards posed by the Cascadia Subduction Zone, it is critically important to know which area of the plate interface is locked and whether or not part of the energy is being released aseismically by slow creep on the fault. Deeper locking that extends further to the coast produces stronger shaking in population centers. Shallow locking, on the other hand, leads to bigger tsunamis. We will report on and discuss plans for a new amphibious Northern Cascadia Subduction Zone Observatory (NCSZO) that will leverage the existing NEPTUNE cabled seafloor observatory, which is operated by Ocean Networks Canada (ONC), and the onshore network of geodetic stations, which is operated by Natural Resources Canada (NRCan). To create a NCSZO we plan to (1) add a network of seven GPS-Acoustic (GPS-A) sites offshore Vancouver Island, (2) establish a Deformation Front Observatory, and (3) improve the existing onshore geodetic network (see Figure below). The GPS-A stations will provide the undisturbed motion of the Juan de Fuca (JdF) Plate (1), deformation of the JdF plate (2), deformation of the overriding plate (3-7) and a cabled laboratory to study the potential for continuous GPS-A measurements (6). The Deformation Front Observatory will be used to study possible transient slip events using seafloor pressure and tilt instruments and fluid flux meters.

Characters of Vertical Variability with Geodetic Satellites and Ground-based Continuous GPS in Taiwan

NASA Astrophysics Data System (ADS)

Yang, C.-C.; Wu, Y.-H.; Chao, B. F.; Yu, S.-B.

2009-04-01

Present-day GPS network have been extensively used to monitor crustal deformation due to various geodynamic mechanisms. Situated among the Pacific Ring of Fire on the suture zone of Eurasian and Philippine Sea Plates, the island of Taiwan with a dense continuous GPS network since ~1996 and now over 300 stations sees plenty of geophysical phenomena including particularly prominent crustal motions. We assessed daily solution of each station's coordinate time series, and made the routine corrections, such as orbital, EOP, atmospheric and tidal corrections, using GAMIT/GLOBK software (with ITRF05). We then employ the Quasi-Observation Combination Analysis (QOCA) package to obtain the variability and trend after removing occasional earthquake "disruptions". Preliminary results show strong seasonal variations. We then utilize the numerical method of Empirical Orthogonal Function (EOF) to analysis the geophysical signals from the continuous and dense GPS vertical crustal motion observations. We wish to be able to characterize both the seasonal and non-seasonal variability in the vertical crustal motion, in terms of the EOF modes in the spatial domain over Taiwan (plus a few offshore islets) with time evolution spanning the entire period of time. Corraborating with time-variable gravity data from the geodetic satellite mission GRACE, we can further obtain vertical components of both mass-induced loading with respect to the precipitation minus evaporation and the crustal motion caused by the active tectonic processes on Taiwan.

Northward migration of the Cascadia forearc in the northwestern U.S. and implications for subduction deformation

USGS Publications Warehouse

Wells, R.E.; Simpson, R.W.

2001-01-01

Geologic and paleomagnetic data from the Cascadia forearc indicate long-term northward migration and clockwise rotation of an Oregon coastal block with respect to North America. Paleomagnetic rotation of coastal Oregon is linked by a Klamath Mountains pole to geodetically and geologically determined motion of the Sierra Nevada block to derive a new Oregon Coast-North America (OC-NA) pole of rotation and velocity field. This long-term velocity field, which is independent of Pacific Northwest GPS data, is interpreted to be the result of Basin-Range extension and Pacific-North America dextral shear. The resulting Oregon Coast pole compares favorably to those derived solely from GPS data, although uncertainties are large. Subtracting the long-term motion from forearc GPS velocities reveals ENE motion with respect to an OC reference frame that is parallel to the direction of Juan de Fuca-OC convergence and decreases inland. We interpret this to be largely the result of subduction-related deformation. The adjusted mean GPS velocities are generally subparallel to those predicted from elastic dislocation models for Cascadia, but more definitive interpretations await refinement of the present large uncertainty in the Sierra Nevada block motion. Copyright ?? The Society of Geomagnetism and Earth, Planetary and Space Sciences (SGEPSS); The Seismological Society of Japan; The Volcanological Society of Japan; The Geodetic Society of Japan; The Japanese Society for Planetary Sciences.

The kinematic response of Petermann Glacier, Greenland to ice shelf perturbation

NASA Astrophysics Data System (ADS)

Hubbard, A.; Box, J. E.; Bates, R.; Nick, F.; Luckman, A. J.; van de Wal, R.; Doyle, S. H.

2010-12-01

The acceleration and dynamic thinning of interior zones of the polar ice sheets due to outlet/ice shelf retreat has been identified as a factor hastening their demise and contribution to global sea-level rise. The detachment of a 275 square km area of the Petermann Glacier ice shelf in August, 2010 presents a natural experiment to investigate the timing, mechanisms and efficacy of upstream dynamic feedbacks resulting from a singular but potentially significant frontal perturbation. In 2009, a permanent geodetic/differential GPS strain network logging every 10 seconds was deployed along a 200 km longitudinal profile from the ice front across the grounding line extending into the interior of Petermann Glacier to characterize the system’s state before, during and after any such event. We present an overview of the geophysical measurements conducted and analyze the kinematics of the shelf detachment in relation to local environmental forcing. Finally, we discuss the postulated instantaneous and ongoing evolution in force-balance and concomitant dynamic response resulting from the perturbation along with its implications for Petermann's ongoing stability. Petermann Glacier GNSS base & telemetric GPS facility: community AA & rehab meet point. On ice geodetic-GPS station flat out & reading 0 Volts

Recording Plate Boundary Deformation Processes Around The San Jacinto Fault, California

NASA Astrophysics Data System (ADS)

Hodgkinson, K.; Mencin, D.; Borsa, A.; Fox, O.; Walls, C.; Van Boskirk, E.

2012-04-01

The San Jacinto Fault is one of the major faults which form the San Andreas Fault System in southern California. The fault, which lies to the west of the San Andreas, is one of the most active in the region. While strain rates are higher along the San Andreas, 23-37 mm/yr compared to 12-22 mm/yr along the San Jacinto, there have been 11 earthquakes of M6 and greater along the San Jacinto in the past 150 years while there have been none of this magnitude on the San Andreas in this region. UNAVCO has installed an array of geodetic and seismic instruments along the San Jacinto as part of the Plate Boundary Observatory (PBO). The network includes 25 GPS stations within 20 km of the surface trace with a concentration of borehole instrumentation in the Anza region where there are nine boreholes sites. Most of the borehole sites contain a GTSM21 4-component strainmeter, a Sonde-2 seismometer, a MEMS accelerometer and a pore pressure sensor. Thus, the array has the capability to capture plate boundary deformation processes with periods of milliseconds (seismic) to decades (GPS). On July 7th 2010 a M5.4 earthquake occurred on the Coyote Creek segment of the fault. The event was preceded by a M4.9 earthquake in the same area four weeks earlier and four earthquakes of M5 and greater within a 20 km radius of the epicenter in the past 50 years. In this study we will present the signals recorded by the different instrument types for the July 7th 2010 event and will compare the coseismic displacements recorded by the GPS and strainmeters with the displacement field predicted by Okada [1992]. All data recorded as part of the PBO observatory are publically available from the UNAVCO, the IRIS Data Management Center and the Northern California Earthquake Data Center.

May tropospheric noise in satellite radar data affect decision making results?

NASA Astrophysics Data System (ADS)

Bloutsos, Aristeidis; Bekri, Eleni; Moschas, Fanis; Saltogianni, Vasso; Stiros, Stathis; Yannopoulos, Panayotis

2015-04-01

Meteorological and air pollution conditions affect the satellite positioning signals. To investigate the uncertainty introduced in these signals in various meteorological and air pollution conditions, an array of GPS/GNSS stations and another of meteorological and air pollution stations has been established. The study area is expanded next to Patraikos and Corinth Gulf (NW Peloponnisos, Greece), which is characterized by high variability sequences from hot to cold weather, low to high relative humidity and clear to cloudy or/and Sahara dusty atmosphere, as a result of the particular geographical and topographical features of the study area. The GNSS recordings from several stations with very high vertical separation (with altitude up to 1600m and with a gradient of up to 20%) are analyzed in order to control in some extend both the vertical and the horizontal variability of the atmospheric effects, as well as the noise of geodetic recordings. Then, the GPS results will be combined with meteorological and atmospheric pollution data, as well as satellite radar data, in order to evaluate the enhanced troposphere noise in satellite radar and to estimate the magnitude of uncertainty that may cause alterations to decision making results in the management of water and other natural resources. This project takes advantage of GPS stations established in wider study area in the framework of the Corinth Rift Laboratory (http://crlab.eu/) in conjunction to the air pollution and meteorological monitoring stations of the Environmental Engineering Laboratory of the Department of Civil Engineering of the University of Patras. Regarding GPS stations, the project has been partly funded by the PLATO Project of the Greek Secretariat for Research and Technology.

Identifying and Allocating Geodetic Systems to historical oil gas wells by using high-resolution satellite imagery

NASA Astrophysics Data System (ADS)

Alvarez, Gabriel O.

2018-05-01

Hydrocarbon exploration in Argentina started long before the IGM created a single, high-precision geodetic reference network for the whole country. Several geodetic surveys were conducted in every producing basin, which have ever since then supported well placement. Currently, every basin has a huge amount of information referenced to the so-called "local" geodetic systems, such as Chos Malal - Quiñi Huao in the Neuquén Basin, and Pampa del Castillo in the San Jorge Basin, which differ to a greater or lesser extent from the national Campo Inchauspe datum established by the IGM in 1969 as the official geodetic network. However, technology development over the last few years and the expansion of satellite positioning systems such as GPS resulted in a new world geodetic order. Argentina rapidly joined this new geodetic order through the implementation of a new national geodetic system by the IGM: POSGAR network, which replaced the old national Campo Inchauspe system. However, this only helped to worsen the data georeferencing issue for oil companies, as a third reference system was added to each basin. Now every basin has a local system, the national system until 1997 (Campo Inchauspe), and finally the newly created POSGAR network national satellite system, which is geocentric unlike the former two planimetric datums. The purpose of this paper is to identify and allocate geodetic systems of coordinates to historical wells, whose geodetic system is missing or has been erroneously allocated, by using currently available technological resources such as geographic information systems and high-resolution satellite imagery.

GNSS Monitoring of Deformation within heavy civil infrastructure

NASA Astrophysics Data System (ADS)

Montillet, Jean-Philippe; Melbourne, Timothy; Szeliga, Walter; Schrock, Gavin

2015-04-01

The steady increase in precision simultaneous with the decreasing of continuous GPS monitoring has enabled the deployment of receivers for a host of new activities. Here we discuss the precision obtained from several multi-station installations operated over a five-year period on several heavy civil-engineered structures, including two earthen-fill dams and subsiding highway overpass damaged by seismic shaking. In the past 5 years, the Cascadia Hazards Institute (Pacific Northwest Geodetic Array) at Central Washington University together with the Washington department of public utilities (Land Survey) have been monitoring several structures around Seattle area including two dams (Howard Hansen and Tolt). One aim of this study is to test the use of continuous GNSS in order to detect any deformations due to rapid pool level rises or to monitor the safety of a structure when an Earthquake strikes it. In this study, data is processed using Real Time Kinematic GPS with short baseline (d < 500 m) and GPS daily position (PPP). However, multipath is the most limiting factor on accuracy for very precise positioning applications with GPS. It is very often present indoors and outdoors, especially in narrow valleys with a limited view of the sky. As a result, multipath can amount to an error of a few centimetres. Unfortunately, the accuracy requirements of precision deformation monitoring are generally at the sub centimetre level, which is presently a big challenge on an epoch-by-epoch basis with regular, carrier phase techniques. Thus, it needs to be properly mitigated. In this study, several stations are set up on the dams (4 stations on the Tolt reservoir and 10 stations on the Howard Hansen dam), and spatial filtering can then be used to mitigate multipath. In addition, several signal processing techniques are also investigated (i.e. Empirical mode decomposition, sidereal filtering, adaptive filtering). RTK GPS should allow to monitor rapid deformations, whereas GPS daily position is used to detect long-term deformations such as the pool level rises due to the melting of ice cap on surrounding mountains. Note that RTK measurements are processed with the MIT software TRACK and the GPS daily positions estimated with GAMIT-GLOBK.

Breadth of Scientific Activities and Network Station Specifications in the IGS

NASA Technical Reports Server (NTRS)

Moore, A. W.; Springer, T. A.; Reigber, Ch.

1999-01-01

This presentation provides a brief overview of the scientific activities of the International GPS Service (IGS). This was an approved activity of the International Association of Geodesy (IAG) with official start of service on 1 Jan 1994. The mission of the IGS is "To provide a service to support geodetic and geophysical research activities, through GPS data and data products." The presentation explains the concept of the IGS working group, and pilot projects, and reviews the current working groups and pilot projects.

Measuring precise sea level from a buoy using the Global Positioning System

NASA Technical Reports Server (NTRS)

Rocken, Christian; Kelecy, Thomas M.; Born, George H.; Young, Larry E.; Purcell, George H., Jr.; Wolf, Susan Kornreich

1990-01-01

The feasibility of using the Global Positioning System (GPS) for accurate sea surface positioning was examined. An experiment was conducted on the Scripps pier at La Jolla, California from December 13-15, 1989. A GPS-equipped buoy was deployed about 100 m off the pier. Two fixed reference GPS receivers, located on the pier and about 80 km away on Monument Peak, were used to estimate the relative position of the floater. Kinematic GPS processing software, developed at the National Geodetic Survey, and the Jet Propulsion Laboratory's GPS Infrared Processing System software were used to determine the floater position relative to land-fixing receivers. Calculations were made of sea level and ocean wave spectra from GPS measurements. It is found that the GPS sea level for the short 100 m baseline agrees with the PPT sea level at the 1 cm level and has an rms variation of 5 mm over a period of 4 hours.

A Real-Time Capable Software-Defined Receiver Using GPU for Adaptive Anti-Jam GPS Sensors

PubMed Central

Seo, Jiwon; Chen, Yu-Hsuan; De Lorenzo, David S.; Lo, Sherman; Enge, Per; Akos, Dennis; Lee, Jiyun

2011-01-01

Due to their weak received signal power, Global Positioning System (GPS) signals are vulnerable to radio frequency interference. Adaptive beam and null steering of the gain pattern of a GPS antenna array can significantly increase the resistance of GPS sensors to signal interference and jamming. Since adaptive array processing requires intensive computational power, beamsteering GPS receivers were usually implemented using hardware such as field-programmable gate arrays (FPGAs). However, a software implementation using general-purpose processors is much more desirable because of its flexibility and cost effectiveness. This paper presents a GPS software-defined radio (SDR) with adaptive beamsteering capability for anti-jam applications. The GPS SDR design is based on an optimized desktop parallel processing architecture using a quad-core Central Processing Unit (CPU) coupled with a new generation Graphics Processing Unit (GPU) having massively parallel processors. This GPS SDR demonstrates sufficient computational capability to support a four-element antenna array and future GPS L5 signal processing in real time. After providing the details of our design and optimization schemes for future GPU-based GPS SDR developments, the jamming resistance of our GPS SDR under synthetic wideband jamming is presented. Since the GPS SDR uses commercial-off-the-shelf hardware and processors, it can be easily adopted in civil GPS applications requiring anti-jam capabilities. PMID:22164116

A real-time capable software-defined receiver using GPU for adaptive anti-jam GPS sensors.

PubMed

Seo, Jiwon; Chen, Yu-Hsuan; De Lorenzo, David S; Lo, Sherman; Enge, Per; Akos, Dennis; Lee, Jiyun

2011-01-01

Due to their weak received signal power, Global Positioning System (GPS) signals are vulnerable to radio frequency interference. Adaptive beam and null steering of the gain pattern of a GPS antenna array can significantly increase the resistance of GPS sensors to signal interference and jamming. Since adaptive array processing requires intensive computational power, beamsteering GPS receivers were usually implemented using hardware such as field-programmable gate arrays (FPGAs). However, a software implementation using general-purpose processors is much more desirable because of its flexibility and cost effectiveness. This paper presents a GPS software-defined radio (SDR) with adaptive beamsteering capability for anti-jam applications. The GPS SDR design is based on an optimized desktop parallel processing architecture using a quad-core Central Processing Unit (CPU) coupled with a new generation Graphics Processing Unit (GPU) having massively parallel processors. This GPS SDR demonstrates sufficient computational capability to support a four-element antenna array and future GPS L5 signal processing in real time. After providing the details of our design and optimization schemes for future GPU-based GPS SDR developments, the jamming resistance of our GPS SDR under synthetic wideband jamming is presented. Since the GPS SDR uses commercial-off-the-shelf hardware and processors, it can be easily adopted in civil GPS applications requiring anti-jam capabilities.

Confirmation of Arabia plate slow motion by new GPS data in Yemen

NASA Astrophysics Data System (ADS)

Vigny, Christophe; Huchon, Philippe; Ruegg, Jean-Claude; Khanbari, Khaled; Asfaw, Laike M.

2006-02-01

During the last 10 years, a network of about 30 GPS sites was measured in Djibouti, East Africa. Additional points were also measured in Yemen, Oman, Ethiopia, Iran, and on La Réunion island. Merged with data from the available International GPS Service permanent stations scattered on the different plates in the area (Eurasia, Anatolia, Africa, Arabia, Somalia), this unique data set provides new insight on the current deformation in the Africa-Somalia-Arabia triple junction area and on the Arabian plate motion. Here we show that coherent motions of points in Yemen, Bahrain, Oman, and Iran allow us to estimate a geodetically constrained angular velocity for the Arabian plate (52.59°N, 15.74°W, 0.461°/Myr in ITRF2000). This result differs significantly from earlier determinations and is based upon our vectors in Yemen. They provide new additional data and better geometry for angular velocity determination. Combined with the African and Somalian motions, this new angular velocity results in predicted spreading rates in the Red Sea and the Gulf of Aden which are 15-20% lower than those measured from oceanic magnetic anomalies and thus averaged over the last 3 Myr. With respect to Eurasia, the geodetic motion of Arabia is also about 30% slower than predicted by NUVEL-1A. On the basis of the kinematic results presented here and on other evidence for a similar slower geodetic rate of the Indian plate, we suggest that the whole collision zone between Africa, Arabia, India on one hand and Eurasia on the other hand has slowed down in the last 3 Myr.

Reconciling geodetic and geological estimates of recent plate motion across the Southwest Indian Ridge

NASA Astrophysics Data System (ADS)

DeMets, C.; Calais, E.; Merkouriev, S.

2017-01-01

We use recently published, high-resolution reconstructions of the Southwest Indian Ridge to test whether a previously described systematic difference between Global Positioning System (GPS) and 3.16-Myr-average estimates of seafloor spreading rates between Antarctica and Africa is evidence for a recent slowdown in Southwest Indian Ridge seafloor spreading rates. Along the Nubia-Antarctic segment of the ridge, seafloor opening rates that are estimated with the new, high-resolution reconstructions and corrected for outward displacement agree well with geodetic rate estimates and reduce previously reported, highly significant non-closure of the Nubia-Antarctic-Sur plate circuit. The observations are inconsistent with a slowdown in spreading rates and instead indicate that Nubia-Antarctic plate motion has been steady since at least 5.2 Ma. Lwandle-Antarctic seafloor spreading rates that are estimated from the new high-resolution reconstructions differ insignificantly from a GPS estimate, thereby implying steady Lwandle-Antarctic plate motion since 5.2 Ma. Between the Somalia and Antarctic plates, the new Southwest Indian Ridge reconstructions eliminate roughly half of the systematic difference between the GPS and MORVEL spreading rate estimates.We interpret the available observations as evidence that Somalia-Antarctic spreading rates have been steady since at least 5.2 Ma and postulate that the remaining difference is attributable to random and/or systematic errors in the plate kinematic estimates and the combined effects of insufficient geodetic sampling of undeforming areas of the Somalia plate, glacial isostatic adjustment in Antarctica and transient deformation triggered by the 1998 Mw = 8.2 Antarctic earthquake, the 2004 Mw = 9.3 Sumatra earthquake, or possibly other large historic earthquakes.

A high-precision, distributed geodetic strainmeter based on dual coaxial cable Bragg gratings

NASA Astrophysics Data System (ADS)

Fu, J.; Wei, T.; Wei, M.; Shen, Y.

2014-12-01

Observations of surface deformation are essential for understanding a wide range of geophysical problems, including earthquakes, volcanoes, landslides, and glaciers. Current geodetic technologies, such as GPS, InSAR, borehole and laser strainmeters, are costly and limited in their temporal or spatial resolution. Here we present a new type of strainmeter based on coaxial cable Bragg grating (CCBG) sensing technology that provides high-precision, distributed strain measurements at a moderate cost. The coaxial-cable-based strainmeter is designed to cover a long distance (~ km) under harsh environmental conditions such as extreme temperatures. To minimize the environmental noises, two CCBGs are introduced into the geodetic strainmeter: one is used to measure the strain applied on it, and the other acts as a reference only to detect the environmental noises. The environmental noises are removed using the inputs from the strained CCBG and the reference CCBG in a frequency mixer. The test results show that the geodetic strainmeter with dual CCBGs has micron-strain accuracy in the lab.

Diffuse Pacific-North American plate boundary: 1000 km of dextral shear inferred from modeling geodetic data

USGS Publications Warehouse

Parsons, T.; Thatcher, W.

2011-01-01

Geodetic measurements tell us that the eastern part of the Basin and Range Province expands in an east-west direction relative to stable North America, whereas the western part of the province moves to the northwest. We develop three-dimensional finite element representations of the western United States lithosphere in an effort to understand the global positioning system (GPS) signal. The models are constrained by known bounding-block velocities and topography, and Basin and Range Province deformation is represented by simple plastic (thermal creep) rheology. We show that active Basin and Range spreading by gravity collapse is expected to have a strong southward component that does not match the GPS signal. We can reconcile the gravitational component of displacement with observed velocity vectors if the Pacific plate applies northwest-directed shear stress to the Basin and Range via the Sierra Nevada block. This effect reaches at least 1000 km east of the San Andreas fault in our models. ?? 2011 Geological Society of America.

GPS baseline configuration design based on robustness analysis

NASA Astrophysics Data System (ADS)

Yetkin, M.; Berber, M.

2012-11-01

The robustness analysis results obtained from a Global Positioning System (GPS) network are dramatically influenced by the configurationof the observed baselines. The selection of optimal GPS baselines may allow for a cost effective survey campaign and a sufficiently robustnetwork. Furthermore, using the approach described in this paper, the required number of sessions, the baselines to be observed, and thesignificance levels for statistical testing and robustness analysis can be determined even before the GPS campaign starts. In this study, wepropose a robustness criterion for the optimal design of geodetic networks, and present a very simple and efficient algorithm based on thiscriterion for the selection of optimal GPS baselines. We also show the relationship between the number of sessions and the non-centralityparameter. Finally, a numerical example is given to verify the efficacy of the proposed approach.

Afar-wide Crustal Strain Field from Multiple InSAR Tracks

NASA Astrophysics Data System (ADS)

Pagli, C.; Wright, T. J.; Wang, H.; Calais, E.; Bennati Rassion, L. S.; Ebinger, C. J.; Lewi, E.

2010-12-01

Onset of a rifting episode in the Dabbahu volcanic segment, Afar (Ethiopia), in 2005 renewed interest in crustal deformation studies in the area. As a consequence, an extensive geodetic data set, including InSAR and GPS measurements have been acquired over Afar and hold great potential towards improving our understanding of the extensional processes that operate during the final stages of continental rupture. The current geodetic observational and modelling strategy has focused on detailed, localised studies of dyke intrusions and eruptions mainly in the Dabbahu segment. However, an eruption in the Erta ‘Ale volcanic segment in 2008, and cluster of earthquakes observed in the Tat Ale segment, are testament to activity elsewhere in Afar. Here we make use of the vast geodetic dataset available to obtain strain information over the whole Afar depression. A systematic analysis of all the volcanic segments, including Dabbahu, Manda-Hararo, Alayta, Tat ‘Ale Erta Ale and the Djibouti deformation zone, is undertaken. We use InSAR data from multiple tracks together with available GPS measurements to obtain a velocity field model for Afar. We use over 300 radar images acquired by the Envisat satellite in both descending and ascending orbits, from 12 distinct tracks in image and wide swath modes, spanning the time period from October 2005 to present time. We obtain the line-of-sight deformation rates from each InSAR track using a network approach and then combine the InSAR velocities with the GPS observations, as suggested by Wright and Wang (2010) following the method of England and Molnar (1997). A mesh is constructed over the Afar area and then we solve for the horizontal and vertical velocities on each node. The resultant full 3D Afar-wide velocity field shows where current strains are being accumulated within the various volcanic segments of Afar, the width of the plate boundary deformation zone and possible connections between distinct volcanic segments on a regional scale. A comparison of crustal strains from the geodetic analysis with the seismicity data will also be made.

Converting NAD83 GPS Heights Into NAVD88 Elevations With LVGEOID, a Hybrid Geoid Height Model for the Long Valley Volcanic Region, California

USGS Publications Warehouse

Battaglia, Maurizio; Dzurisin, Daniel; Langbein, John; Svarc, Jerry; Hill, David P.

2008-01-01

A GPS survey of leveling benchmarks done in Long Valley Caldera in 1999 showed that the application of the National Geodetic Survey (NGS) geoid model GEOID99 to tie GPS heights to historical leveling measurements would significantly underestimate the caldera ground deformation (known from other geodetic measurements). The NGS geoid model was able to correctly reproduce the shape of the deformation, but required a local adjustment to give a realistic estimate of the magnitude of the uplift. In summer 2006, the U.S. Geological Survey conducted a new leveling survey along two major routes crossing the Long Valley region from north to south (Hwy 395) and from east to west (Hwy 203 - Benton Crossing). At the same time, 25 leveling bench marks were occupied with dual frequency GPS receivers to provide a measurement of the ellipsoid heights. Using the heights from these two surveys, we were able to compute a precise geoid height model (LVGEOID) for the Long Valley volcanic region. Our results show that although the LVGEOID and the latest NGS GEOID03 model practically coincide in areas outside the caldera, there is a difference of up to 0.2 m between the two models within the caldera. Accounting for this difference is critical when using the geoid height model to estimate the ground deformation due to magmatic or tectonic activity in the caldera.

ERP-Variations on Time Scales Between Hours and Months Derived From GNSS Observations

NASA Astrophysics Data System (ADS)

Weber, R.; Englich, S.; Mendes Cerveira, P.

2007-05-01

Current observations gained by the space geodetic techniques, especially VLBI, GPS and SLR, allow for the determination of Earth Rotation Parameters (ERPs - polar motion, UT1/LOD) with unprecedented accuracy and temporal resolution. This presentation focuses on contributions to the ERP recovery provided by satellite navigation systems (primarily GPS). The IGS (International GNSS Service), for example, currently provides daily polar motion with an accuracy of less than 0.1mas and LOD estimates with an accuracy of a few microseconds. To study more rapid variations in polar motion and LOD we established in a first step a high resolution (hourly resolution) ERP-time series from GPS observation data of the IGS network covering the year 2005. The calculations were carried out by means of the Bernese GPS Software V5.0 considering observations from a subset of 113 fairly stable stations out of the IGS05 reference frame sites. From these ERP time series the amplitudes of the major diurnal and semidiurnal variations caused by ocean tides are estimated. After correcting the series for ocean tides the remaining geodetic observed excitation is compared with variations of atmospheric excitation (AAM). To study the sensitivity of the estimates with respect to the applied mapping function we applied both the widely used NMF (Niell Mapping Function) and the VMF1 (Vienna Mapping Function 1). In addition, based on computations covering two months in 2005, the potential improvement due to the use of additional GLONASS data will be discussed.

Tectonic deformation in southern California

NASA Technical Reports Server (NTRS)

Jackson, David D.

1993-01-01

Our objectives were to use modem geodetic data, especially those derived from space techniques like Very Long Baseline Interferometry (VLBI), Satellite Laser Ranging (SLR), and the Global Positioning System (GPS) to infer crustal deformation in southern California and relate it to plate tectonics and earthquake hazard. To do this, we needed to collect some original data, write computer programs to determine positions of survey markers from geodetic observables, interpret time dependent positions in terms of velocity and earthquake caused episodic displacements, and construct a model to explain these velocities and displacements in terms of fault slip and plate movements.

GPS data exploration for seismologists and geodesists

NASA Astrophysics Data System (ADS)

Webb, F.; Bock, Y.; Kedar, S.; Dong, D.; Jamason, P.; Chang, R.; Prawirodirdjo, L.; MacLeod, I.; Wadsworth, G.

2007-12-01

Over the past decade, GPS and seismic networks spanning the western US plate boundaries have produced vast amounts of data that need to be made accessible to both the geodesy and seismology communities. Unlike seismic data, raw geodetic data requires significant processing before geophysical interpretations can be made. This requires the generation of data-products (time series, velocities and strain maps) and dissemination strategies to bridge these differences and assure efficient use of data across traditionally separate communities. "GPS DATA PRODUCTS FOR SOLID EARTH SCIENCE" (GDPSES) is a multi-year NASA funded project, designed to produce and deliver high quality GPS time series, velocities, and strain fields, derived from multiple GPS networks along the western US plate boundary, and to make these products easily accessible to geophysicists. Our GPS product dissemination is through modern web-based IT methodology. Product browsing is facilitated through a web tool known as GPS Explorer and continuous streams of GPS time series are provided using web services to the seismic archive, where it can be accessed by seismologists using traditional seismic data viewing and manipulation tools. GPS-Explorer enables users to efficiently browse several layers of data products from raw data through time series, velocities and strain by providing the user with a web interface, which seamlessly interacts with a continuously updated database of these data products through the use of web-services. The current archive contains GDPSES data products beginning in 1995, and includes observations from GPS stations in EarthScope's Plate Boundary Observatory (PBO), as well as from real-time real-time CGPS stations. The generic, standards-based approach used in this project enables GDPSES to seamlessly expand indefinitely to include other space-time-dependent data products from additional GPS networks. The prototype GPS-Explorer provides users with a personalized working environment in which the user may zoom in and access subsets of the data via web services. It provides users with a variety of interactive web tools interconnected in a portlet environment to explore and save datasets of interest to return to at a later date. At the same time the GPS time series are also made available through the seismic data archive, where the GPS networks are treated as regular seismic networks, whose data is made available in data formats used by seismic utilities such as SEED readers and SAC. A key challenge, stemming from the fundamental differences between seismic and geodetic time series, is the representation of reprocessed of GPS data in the seismic archive. As GPS processing algorithms evolve and their accuracy increases, a periodic complete recreation of the the GPS time series archive is necessary.

New insights into the kinematics and seismotectonics of the Adria-Eurasia boundary in the eastern Alps from geodetic and seismic data

NASA Astrophysics Data System (ADS)

Serpelloni, Enrico; Vannucci, Gianfranco; Bennett, Richard A.; Anderlini, Letizia; Cavaliere, Adriano

2015-04-01

In this work we describe a new kinematic and seismotectonic model of the eastern Alps, at the boundary between Italy, Austria, Slovenia and Croatia, obtained from the analysis of geodetic (GPS) and seismological data. We use a dense GPS velocity field, obtained from integration of continuous, semi-continuous and survey-mode networks (~200 GPS stations between longitude 10°E and 17°E and latitude 44.5°N and 47.5°N) and an updated seismic and focal mechanisms catalogue, with uniformly calibrated moment magnitudes from ~1000 B.C.. Improved accuracies and precisions of GPS motion rates have been obtained by filtering displacement time-series for the spatially correlated common mode errors. The eastern Alps mark the boundary between the Adriatic microplate and the Eurasian plate through a wide zone of distributed deformation. Geodetic deformation and seismic release are more localized, and characterized by larger earthquakes, along the southeastern Alps fold-and-thrust belt, which accommodates the large part of the ~N-S Adria-Eurasia convergence, and in Slovenia, where a transition from ~N-S shortening to the eastward escape of the Pannonian Basin units occurs through a complex pattern of crustal deformation. GPS velocities well describe the overall kinematics, with a transition from NNW-ward to NE-ward motion trends (in a Eurasian frame) across Slovenia and Austria, but also show small but significant crustal deformation far from the major blocks boundaries. This may suggest internal continuous deformation or a more complex configuration of interacting tectonic blocks in the eastern Alps. This second hypothesis is taken into account and tested in this work. We use seismic moment release rate maps, active faults databases and inspections of GPS velocities in different local frames to define the geometry of a kinematic block model, constrained by GPS horizontal velocities, in order to estimate blocks rotations and elastic strain at blocks bounding faults. The improved GPS velocity field highlights significant strain accumulation off the main thrust fault segments in the southeastern Alps, in regions stroke by large (M>6.5) historical earthquakes (e.g., the 1117 Verona and the 1695 Asolo events). This is evident in the Venetian plain, where GPS highlights significant shortening in areas that are tens of km southward of the south Alpine mountain front. In the Italian southeastern Alps results from the block model, constrained by a denser GPS velocity field (e.g., around the Montello fault), put new lights on i) the way the Adria-Eurasia convergence is partitioned across the southeast Alpine mountain range, ii) about interseismic coupling along the main thrust faults and iii) the way N-S shortening is transferred, through right-lateral shear across the Dinaric system, to shortening across the Sava folds in Slovenia. In the end, a comparison of the estimated seismic moment release rates and the seismic moment accumulation rates, estimated from the model velocities, provide new insights into the seismic potential of the study region.

Geodetic Volcano Monitoring Research in Canary Islands: Recent Results

NASA Astrophysics Data System (ADS)

Fernandez, J.; Gonzalez, P. J.; Arjona, A.; Camacho, A. G.; Prieto, J. F.; Seco, A.; Tizzani, P.; Manzo, M. R.; Lanari, R.; Blanco, P.; Mallorqui, J. J.

2009-05-01

The Canarian Archipelago is an oceanic island volcanic chain with a long-standing history of volcanic activity (> 40 Ma). It is located off the NW coast of the African continent, lying over a transitional crust of the Atlantic African passive margin. At least 12 eruptions have been occurred on the islands of Lanzarote, Tenerife and La Palma in the last 500 years. Volcanism manifest predominantly as basaltic strombolian monogenetic activity (whole archipelago) and central felsic volcanism (active only in Tenerife Island). We concentrate our studies in the two most active islands, Tenerife and La Palma. In these islands, we tested different methodologies of geodetic monitoring systems. We use a combination of ground- and space-based techniques. At Tenerife Island, a differential interferometric study was performed to detect areas of deformation. DInSAR detected two clear areas of deformation, using this results a survey-based GPS network was designed and optimized to control those deformations and the rest of the island. Finally, using SBAS DInSAR results weak spatial long- wavelength subsidence signals has been detected. At La Palma, the first DInSAR analysis have not shown any clear deformation, so a first time series analysis was performed detecting a clear subsidence signal at Teneguia volcano, as for Tenerife a GPS network was designed and optimized taking into account stable and deforming areas. After several years of activities, geodetic results served to study ground deformations caused by a wide variety of sources, such as changes in groundwater levels, volcanic activity, volcano-tectonics, gravitational loading, etc. These results proof that a combination of ground-based and space-based techniques is suitable tool for geodetic volcano monitoring in Canary Islands. Finally, we would like to strength that those results could have serious implications on the continuous geodetic monitoring system design and implementation for the Canary Islands which is under development nowadays.

A Constellation of Microsatellites Promises to Help in a Range of Geoscience Research

NASA Technical Reports Server (NTRS)

Kuo, Y. H.; Chao, B. F.; Lee, L. C.

1999-01-01

An octet of microsatellites to be launched in 2003 promises to deliver a large amount of useful data for meteorological, climatic, ionospheric, and geodetic research as well as for operational weather forecasting and space weather monitoring. Known as the Constellation Observing System for Meteorology, Ionosphere, and Climate (COSMIC), the joint Taiwan-U.S. scientific satellite project makes use of Global Positioning System (GPS) occultation and tracking signals. COSMIC's final operational configuration is depicted in Figure 1. Each of the eight microsatellites in low-Earth-orbit (LEO, shown relative to the high-altitude GPS satellite orbits) will carry in particular an advanced limb-sounding GPS receiver, a Tiny Ionospheric Photometer, and a triband beacon transmitter.

Evaluation and Preliminary Results of the New USNO PPS Timing Receiver

DTIC Science & Technology

2000-11-01

timing receiver, one may currently obtain raw pseudorange and carrier-phase data by periodically downloading such data from a flashcard . Several...preliminary experiments have been performed using data collected from the prototype TTR- 12 receivers’ flashcards and geodetic GPS carrier-phase techniques

Results from a model-independent method of monitoring a geodetic network for patterns of transient deformation

NASA Technical Reports Server (NTRS)

Hurst, Kenneth; Granat, Robert

2005-01-01

We have implmented two multi-station detectors for transient crustal deformation within the Southern California Integrated GPS (SCGIN). One the the primary goals of SCIGN is to detect transient deformation associated with the earthquake cycle in Southern California.

The Accidental Tide Gauge: A GPS Reflection Case Study from Kachemak Bay, Alaska

NASA Technical Reports Server (NTRS)

Larson, Kristine M.; Ray, Richard D.; Nievinski, Felipe G..; Freymueller, Jeffrey T.

2013-01-01

For the last decade, it has been known that reflected GPS signals observed with specialized instruments could be used to measure sea level. In this letter, data from an existing geodeticquality GPS site near Kachemak Bay, Alaska, are analyzed for a one-year time period. Daily sea-level variations are more than 7 m. Tidal coefficients have been estimated and compared with coefficients estimated from records from a traditional tide gauge at Seldovia Harbor, approximately 30 km away. The GPS and Seldovia estimates of M(sub 2) and S(sub 2) coefficients agree to better than 2%; much of this residual can be attributed to true differences in the tide over 30 km as it propagates up Kachemak Bay. For daily mean sea levels the agreement is 2.3 cm. Because a standard geodetic GPS receiver/antenna is used, this GPS instrument can measure long-term sea-level changes in a stable terrestrial reference frame.

An accuracy assessment of realtime GNSS time series toward semi- real time seafloor geodetic observation

NASA Astrophysics Data System (ADS)

Osada, Y.; Ohta, Y.; Demachi, T.; Kido, M.; Fujimoto, H.; Azuma, R.; Hino, R.

2013-12-01

Large interplate earthquake repeatedly occurred in Japan Trench. Recently, the detail crustal deformation revealed by the nation-wide inland GPS network called as GEONET by GSI. However, the maximum displacement region for interplate earthquake is mainly located offshore region. GPS/Acoustic seafloor geodetic observation (hereafter GPS/A) is quite important and useful for understanding of shallower part of the interplate coupling between subducting and overriding plates. We typically conduct GPS/A in specific ocean area based on repeated campaign style using research vessel or buoy. Therefore, we cannot monitor the temporal variation of seafloor crustal deformation in real time. The one of technical issue on real time observation is kinematic GPS analysis because kinematic GPS analysis based on reference and rover data. If the precise kinematic GPS analysis will be possible in the offshore region, it should be promising method for real time GPS/A with USV (Unmanned Surface Vehicle) and a moored buoy. We assessed stability, precision and accuracy of StarFireTM global satellites based augmentation system. We primarily tested for StarFire in the static condition. In order to assess coordinate precision and accuracy, we compared 1Hz StarFire time series and post-processed precise point positioning (PPP) 1Hz time series by GIPSY-OASIS II processing software Ver. 6.1.2 with three difference product types (ultra-rapid, rapid, and final orbits). We also used difference interval clock information (30 and 300 seconds) for the post-processed PPP processing. The standard deviation of real time StarFire time series is less than 30 mm (horizontal components) and 60 mm (vertical component) based on 1 month continuous processing. We also assessed noise spectrum of the estimated time series by StarFire and post-processed GIPSY PPP results. We found that the noise spectrum of StarFire time series is similar pattern with GIPSY-OASIS II processing result based on JPL rapid orbit products with 300 seconds interval clock information. And we report stability, precision and accuracy of StarFire in the moving conditon.

The Current Status and Tendency of China Millimeter Coordinate Frame Implementation and Maintenance

NASA Astrophysics Data System (ADS)

Cheng, P.; Cheng, Y.; Bei, J.

2017-12-01

China Geodetic Coordinate System 2000 (CGCS2000) was first officially declared as the national standard coordinate system on July 1, 2008. This reference frame was defined in the ITRF97 frame at epoch 2000.0 and included 2600 GPS geodetic control points. The paper discusses differences between China Geodetic Coordinate System 2000 (CGCS2000) and later updated ITRF versions, such as ITRF2014,in terms of technical implementation and maintenance. With the development of the Beidou navigation satellite system, especially third generation of BDS with signal global coverage in the future, and with progress of space geodetic technology, it is possible for us to establish a global millimeter-level reference frame based on space geodetic technology including BDS. The millimeter reference frame implementation concerns two factors: 1) The variation of geocenter motion estimation, and 2) the site nonlinear motion modeling. In this paper, the geocentric inversion methods are discussed and compared among results derived from various technical methods. Our nonlinear site movement modeling focuses on singular spectrum analysis method, which is of apparent advantages over earth physical effect modeling. All presented in the paper expected to provide reference to our future CGCS2000 maintenance.

Geodetic evidence for continuing tectonic activity of the Carboneras fault (SE Spain)

NASA Astrophysics Data System (ADS)

Echeverria, Anna; Khazaradze, Giorgi; Asensio, Eva; Masana, Eulalia

2015-11-01

The Carboneras fault zone (CFZ) is a prominent onshore-offshore strike-slip fault that forms part of the Eastern Betic Shear Zone (EBSZ), located in SE Spain. In this work, we show for the first time, the continuing tectonic activity of the CFZ and quantify its geodetic slip-rates using continuous and campaign GPS observations conducted during the last decade. We find that the left-lateral motion dominates the kinematics of the CFZ, with a strike-slip rate of 1.3 ± 0.2 mm/yr along the N48° direction. The shortening component is significantly lower and poorly constrained. Recent onshore and offshore paleoseismic and geomorphic results across the CFZ suggest a minimum Late Pleistocene to present-day strike-slip rate of 1.1 mm/yr. Considering the similarity of the geologic and geodetic slip rates measured at different points along the fault, the northern segment of the CFZ must have been slipping approximately at a constant rate during the Quaternary. Regarding the eastern Alpujarras fault zone corridor (AFZ), located to the north of the CFZ, our GPS measurements corroborate that this zone is active and exhibits a right-lateral motion. These opposite type strike-slip motion across the AFZ and CFZ is a result of a push-type force due to Nubia and Eurasia plate convergence, which, in turn, causes the westward escape of the block bounded by these two fault zones.

On the Cause of Geodetic Satellite Accelerations and Other Correlated Unmodeled Phenomena

NASA Astrophysics Data System (ADS)

Mayer, A. F.

2005-12-01

An oversight in the development of the Einstein field equations requires a well-defined amendment to general relativity that very slightly modifies the weak-field Schwarzschild geometry yielding unambiguous new predictions of gravitational relativistic phenomena. The secular accelerations of LAGEOS, Etalon and other geodetic satellites are definitively explained as a previously unmodeled relativistic effect of the gravitational field. Observed dynamic variations may be correlated to the complex dynamic relationship between the satellite angular momentum vector and the solar gravitational gradient associated with the orbital motion of the Earth and the natural precession of the satellite orbit. The Pioneer Anomaly, semidiurnal saw-toothed pseudo-range residuals of GPS satellites, peculiar results of radio occultation experiments, secular accelerations of Solar System moons, the conspicuous excess redshift of white dwarf stars and other documented empirical observations are all correlated to the same newly modeled subtle relativistic energy effect. Modern challenges in the determination and maintenance of an accurate and reliable terrestrial reference frame, difficulties with global time synchronization at nanosecond resolution and the purported existence of unlikely excessive undulations of the Geoid relative to the Ellipsoid are all related to this previously unknown phenomenon inherent to the gravitational field. Doppler satellite measurements made by the TRANSIT system (the precursor to GPS) were significantly affected; WGS 84 coordinates and other geodetic data now assumed to be correct to high accuracy require correction based on the new theoretical developments.

An Investigation on the Crustal Deformations in Istanbul after Eastern Marmara Earthquakes in 1999

NASA Astrophysics Data System (ADS)

Ozludemir, M.; Ozyasar, M.

2008-12-01

Since the introduction of the GPS technique in mid 1970's there has been great advances in positioning activities. Today such Global Navigational Satellite Systems (GNSS) based positioning techniques are widely used in daily geodetic applications. High order geodetic network measurements are one of such geodetic applications. Such networks are established to provide reliable infrastructures for all kind of geodetic work from the production of cadastral plans to the surveying processes during the construction of engineering structures. In fact such positional information obtained in such engineering surveys could be useful for other studies as well. One of such fields is geodynamic studies where such positional information could be valuable to understand the characteristics of tectonic movements. In Turkey being located in a tectonically active zones and having major earthquakes quite frequently, the positional information obtained in engineering surveys could be very useful for earthquake related studies. In this paper an example of such engineering surveys is discussed. This example is the Istanbul GPS (Global Positioning System) Network, first established in 1997 and remeasured in 2005. Between these two measurement processes two major earthquakes took place, on August 17 and November 12, 1999 with magnitudes of 7.4 and 7.2, respectively. In the first measurement campaign in 1997, a network of about 700 points was measured, while in the second campaign in 2005 more than 1800 points were positioned. In these two campaigns are existing common points. The network covers the whole Istanbul area of about 6000 km2. All network points are located on the Eurasian plate to the north of the North Anatolian Fault Zone. In this study, the horizontal and vertical movements are presented and compared with the results obtained in geodynamic studies.

The GPS Topex/Poseidon precise orbit determination experiment - Implications for design of GPS global networks

NASA Technical Reports Server (NTRS)

Lindqwister, Ulf J.; Lichten, Stephen M.; Davis, Edgar S.; Theiss, Harold L.

1993-01-01

Topex/Poseidon, a cooperative satellite mission between United States and France, aims to determine global ocean circulation patterns and to study their influence on world climate through precise measurements of sea surface height above the geoid with an on-board altimeter. To achieve the mission science aims, a goal of 13-cm orbit altitude accuracy was set. Topex/Poseidon includes a Global Positioning System (GPS) precise orbit determination (POD) system that has now demonstrated altitude accuracy better than 5 cm. The GPS POD system includes an on-board GPS receiver and a 6-station GPS global tracking network. This paper reviews early GPS results and discusses multi-mission capabilities available from a future enhanced global GPS network, which would provide ground-based geodetic and atmospheric calibrations needed for NASA deep space missions while also supplying tracking data for future low Earth orbiters. Benefits of the enhanced global GPS network include lower operations costs for deep space tracking and many scientific and societal benefits from the low Earth orbiter missions, including improved understanding of ocean circulation, ocean-weather interactions, the El Nino effect, the Earth thermal balance, and weather forecasting.

Short-and-long-term Slip Rates Along the Carboneras Fault in the Betic Cordillera, Spain

NASA Astrophysics Data System (ADS)

Khazaradze, G.; López, R.; Pallàs, R.; Ortuño, M.; Bordonau, J.; Masana, E.

2017-12-01

We present the new results from our long-standing studies to understand the geodynamic behavior of the Carboneras fault, located in the SE Betic Cordilleras of Spain. Specifically, we quantify the geodetic and geologic slip rates for the onland section of the fault. As a result of our previous GPS observations, we have been able to confirm the continuing tectonic activity of the Carboneras fault: we were able to quantify that the geodetic slip rate of the fault equals 1.3±0.2 mm/yr, expressed mainly as a left-lateral strike slip motion (Echeverria et al., 2015). In autumn 2017, with the purpose of revealing a detailed nature of the crustal deformation and its partitioning between different structures, 3 new continuous GPS stations will be established along the fault-perpendicular profile. In addition, since summer 2016, we have conducted surveys of the nearby CuaTeNeo and IGN Regente campaign points. We have also established and measured several new geodetic points in the vicinity of the fault, with the aim of increasing the spatial coverage around it. The GPS measured, short-term slip rates are in surprising agreement with the estimates of the long-term, geologic slip rates based on paleoseismic studies, which indicate a minimum strike-slip rate of 1.31 mm/yr and dip-slip rate of 0.05 mm/yr since 110.3 ka (Moreno et al. 2015). In order to increase the paleoseismic event database, several new sites have been identified along the fault, where further paleoseismic trenching surveys will be performed within the coming year or two. At the site of Tostana, located at the central part of the fault, in winter 2017 seven trenches have been opened and clear evidence of past earthquakes has been encountered. These new data, combined with the findings of the recent geomorphological study of river offsets (Ferrater, 2016) and new GPS observations, should improve the reliability of the existent deformation data and therefore, will help to better understand the seismic hazard posed by the Carbonears fault in the SE Betics. Project PREVENT (CGL2015-66263-R) financed by the Ministry of Economy, Industry and Competitiveness.

Geodetic slip solutions for the Mw = 7.4 Champerico (Guatemala) earthquake of 2012 November 7 and its postseismic deformation

NASA Astrophysics Data System (ADS)

Ellis, Andria P.; DeMets, Charles; Briole, Pierre; Molina, Enrique; Flores, Omar; Rivera, Jeffrey; Lasserre, Cécile; Lyon-Caen, Hélène; Lord, Neal

2015-05-01

As the first large subduction thrust earthquake off the coast of western Guatemala in the past several decades, the 2012 November 7 Mw = 7.4 earthquake offers the first opportunity to study coseismic and postseismic behaviour along a segment of the Middle America trench where frictional coupling makes a transition from weak coupling off the coast of El Salvador to strong coupling in southern Mexico. We use measurements at 19 continuous GPS sites in Guatemala, El Salvador and Mexico to estimate the coseismic slip and postseismic deformation of the November 2012 Champerico (Guatemala) earthquake. An inversion of the coseismic offsets, which range up to ˜47 mm at the surface near the epicentre, indicates that up to ˜2 m of coseismic slip occurred on a ˜30 × 30 km rupture area between ˜10 and 30 km depth, which is near the global CMT centroid. The geodetic moment of 13 × 1019 N m and corresponding magnitude of 7.4 both agree well with independent seismological estimates. Transient postseismic deformation that was recorded at 11 GPS sites is attributable to a combination of fault afterslip and viscoelastic flow in the lower crust and/or mantle. Modelling of the viscoelastic deformation suggests that it constituted no more than ˜30 per cent of the short-term postseismic deformation. GPS observations that extend six months after the earthquake are well fit by a model in which most afterslip occurred at the same depth or directly downdip from the rupture zone and released energy equivalent to no more than ˜20 per cent of the coseismic moment. An independent seismological slip solution that features more highly concentrated coseismic slip than our own fits the GPS offsets well if its slip centroid is translated ˜50 km to the west to a position close to our slip centroid. The geodetic and seismologic slip solutions thus suggest bounds of 2-7 m for the peak slip along a region of the interface no larger than 30 × 30 km.

Characteristics and limitations of GPS L1 observations from submerged antennas - Theoretical investigation in snow, ice, and freshwater and practical observations within a freshwater layer

NASA Astrophysics Data System (ADS)

Steiner, Ladina; Meindl, Michael; Geiger, Alain

2018-05-01

Observations from a submerged GNSS antenna underneath a snowpack need to be analyzed to investigate its potential for snowpack characterization. The magnitude of the main interaction processes involved in the GPS L1 signal propagation through different layers of snow, ice, or freshwater is examined theoretically in the present paper. For this purpose, the GPS signal penetration depth, attenuation, reflection, refraction as well as the excess path length are theoretically investigated. Liquid water exerts the largest influence on GPS signal propagation through a snowpack. An experiment is thus set up with a submerged geodetic GPS antenna to investigate the influence of liquid water on the GPS observations. The experimental results correspond well with theory and show that the GPS signal penetrates the liquid water up to three centimeters. The error in the height component due to the signal propagation delay in water can be corrected with a newly derived model. The water level above the submerged antenna could also be estimated.

Aftershock distribution as a constraint on the geodetic model of coseismic slip for the 2004 Parkfield earthquake

USGS Publications Warehouse

Bennington, Ninfa; Thurber, Clifford; Feigl, Kurt; ,

2011-01-01

Several studies of the 2004 Parkfield earthquake have linked the spatial distribution of the event’s aftershocks to the mainshock slip distribution on the fault. Using geodetic data, we find a model of coseismic slip for the 2004 Parkfield earthquake with the constraint that the edges of coseismic slip patches align with aftershocks. The constraint is applied by encouraging the curvature of coseismic slip in each model cell to be equal to the negative of the curvature of seismicity density. The large patch of peak slip about 15 km northwest of the 2004 hypocenter found in the curvature-constrained model is in good agreement in location and amplitude with previous geodetic studies and the majority of strong motion studies. The curvature-constrained solution shows slip primarily between aftershock “streaks” with the continuation of moderate levels of slip to the southeast. These observations are in good agreement with strong motion studies, but inconsistent with the majority of published geodetic slip models. Southeast of the 2004 hypocenter, a patch of peak slip observed in strong motion studies is absent from our curvature-constrained model, but the available GPS data do not resolve slip in this region. We conclude that the geodetic slip model constrained by the aftershock distribution fits the geodetic data quite well and that inconsistencies between models derived from seismic and geodetic data can be attributed largely to resolution issues.

Determining Coastal Mean Dynamic Topography by Geodetic Methods

NASA Astrophysics Data System (ADS)

Huang, Jianliang

2017-11-01

In geodesy, coastal mean dynamic topography (MDT) was traditionally determined by spirit leveling technique. Advances in navigation satellite positioning (e.g., GPS) and geoid determination enable space-based leveling with an accuracy of about 3 cm at tide gauges. Recent CryoSat-2, a satellite altimetry mission with synthetic aperture radar (SAR) and SAR interferometric measurements, extends the space-based leveling to the coastal ocean with the same accuracy. However, barriers remain in applying the two space-based geodetic methods for MDT determination over the coastal ocean because current geoid modeling focuses primarily on land as a substitute to spirit leveling to realize the vertical datum.

The AuScope Project and Trans-Tasman VLBI

NASA Technical Reports Server (NTRS)

Lovell, Jim; Dickey, John; Gulyaev, Sergei; Natusch, Tim; Titov, Oleg; Tingay, Steven

2010-01-01

Three 12-meter radio telescopes are being built in Australia (the AuScope project) and one in New Zealand. These facilities will be fully-equipped for undertaking S and X-band geodetic VLBI observations and correlation will take place on a software correlator (part of the AuScope project). All sites are equipped with permanent GPS receivers to provide co-location of several space geodetic techniques. The following scientific tasks of geodesy and astrometry are considered. 1. Improvement and densification of the International Celestial Reference Frame in the southern hemisphere; 2. Improvement of the International Terrestrial Reference Frame in the region; 3. Measurement of intraplate deformation of the Australian tectonic plate.

Long-term comparisons between two-way satellite and geodetic time transfer systems.

PubMed

Plumb, John F; Larson, Kristine M

2005-11-01

Global Positioning System (GPS) observations recorded in the United States and Europe were used to evaluate time transfer capabilities of GETT (geodetic time transfer). Timing estimates were compared with two-way satellite time and frequency transfer (TWSTFT) systems. A comparison of calibrated links at the U.S. Naval Observatory, Washington, D.C., and Colorado Springs, CO, yielded agreement of 2.17 ns over 6 months with a standard deviation of 0.73 ns. An uncalibrated link between the National Institute of Standards and Technology (NIST) and Physikalisch-Technische Bundesanstalt, Braunschweig, Germany, has a standard deviation of 0.79 ns over the same time period.

A study of risk in the metropolitan area of Guadalajara through dense GPS geodesy

NASA Astrophysics Data System (ADS)

Marquez-Azua, B.; Saldana-Hernandez, F.; Medina de La Pena, H.

2007-05-01

Geodesic measurements from the Global Positioning System (GPS) are used extensively for basic earth science research into natural hazards and seismic risk. In the private sector, GPS technology is additionally used for cadastral and photogrammetric mapping surveys, definition of political-administrative limits, space analysis with thematic cartography, GIS, and land-use planning, with a wide variety of applied social, economic, and political purposes, including conservation of the environment. The city of Guadalajara and its surrounding urban area has expanded greatly in the last three decades as a result of industrial, commercial and housing activity that have substantially changed in their urban morphology. This period of unprecedented growth has occurred primarily in an unplanned and sometimes disarticulated and unbalanced manner, incongruous with the development of the most important city in western Mexico. The Department of Geography of the University of Guadalajara and the Institute of Territorial Information of the State of Jalisco (IITJ) have initiated a study of 89 geodetic sites that are located in the metropolitan zone of Guadalajara to assist in future planning and regulation of urban development, including urban and rural cadastral surveys and the establishment of diverse public services. Our work includes careful examination and evaluation of the quality and distribution of these geodetic sites with regard to anticipated growth of the metropolitan municipalities, and the vulnerability of urban zones to ground subsidence or landslides. Guadalajara is also located in a seismic zone, making precise continuous GPS measurements useful for identifying rates of strain accumulation and aseismic strain events that cannot be measured by seismographs.

Some tests of wet tropospheric calibration for the CASA Uno Global Positioning System experiment

NASA Technical Reports Server (NTRS)

Dixon, T. H.; Wolf, S. Kornreich

1990-01-01

Wet tropospheric path delay can be a major error source for Global Positioning System (GPS) geodetic experiments. Strategies for minimizing this error are investigted using data from CASA Uno, the first major GPS experiment in Central and South America, where wet path delays may be both high and variable. Wet path delay calibration using water vapor radiometers (WVRs) and residual delay estimation is compared with strategies where the entire wet path delay is estimated stochastically without prior calibration, using data from a 270-km test baseline in Costa Rica. Both approaches yield centimeter-level baseline repeatability and similar tropospheric estimates, suggesting that WVR calibration is not critical for obtaining high precision results with GPS in the CASA region.

Three decades of harnessing the GPS data explosion for geophysics (Vening Meinesz Medal Lecture)

NASA Astrophysics Data System (ADS)

Blewitt, Geoffrey

2015-04-01

In this presentation, I attempt to convey the immensity of the task that faced the geodesy community three decades ago, and continues to challenge us, to harness all potentially valuable GPS data available in the world for geophysical science. It would be fair to see that three decades ago, we were struggling with controlled tests just to get GPS geodesy working, and had little time to imagine the flood of data today. Yet the geodesy community has succeeded in meeting this challenge. Today, for example, the Nevada Geodetic Laboratory produces and makes publicly available coordinate time series for over 12,000 geodetic GPS station around the globe with various data intervals, latencies, and reference frames. About 8,000 stations have their daily time series updated every week, with 4,000 being updated the next day with coordinates at daily and 5 minute intervals. About 2,000 stations have their time series updated every hour with coordinates at 5 minute intervals. I will show examples of how these time series are being used by NGL and many other scientists to study a wide variety of geophysical topics, including plate tectonics, earthquake modeling, seismic and tsunami hazard, volcanic deformation, water resources, mountain growth, terrestrial reference frame realization, glacial isostatic adjustment, ice sheet melting, sea level rise and coastal subsidence, and even fundamental physics, using GPS atomic clocks to probe the nature of dark matter in the universe. The explosion in GPS data has challenged us to invent new data processing algorithms and develop robust automation in order to keep up with the flood. This explosion has been exponential, and therefore it can be said that it is not a recent phenomena, but rather that it began in the earliest years of GPS geodesy, and has always posed a challenge to us. Over the course of my post-doctoral career starting in late 1985, I have had the good fortune to witness the key developments that have taken place since the early years of geodetic GPS and over the course of three decades. These developments continue today as strongly as ever. Essential innovations have included, for example, automation of GPS cycle slip detection and mitigation, carrier phase ambiguity resolution, the birth and operation of the IGS for reliable orbit and clock estimation, the invention of algorithms that scale linearly with the number of stations, and the deep integration of GPS solutions into the ITRF, providing measures of accuracy, precision, and stability. As a recent example of automation, I show a new non-parametric algorithm to estimate station velocities quickly and robustly, without need to detect and correct for outliers, seasonal signals, and discontinuities in the time series steps that commonly occur due to equipment changes. The complete automation from data collection to production of station velocities (and, now, velocity time series) allows us to process all potentially valuable data, and to focus more on discovery and analysis of the results for geophysical applications, often with great redundancy in the data leading to high statistical significance and more robust scientific conclusions. I show by example that another benefit of this capability to process all data in a robust turn-key fashion is to enhance the opportunity for making discoveries, without necessarily planning all of the steps that can lead us to discovery's door.

Joint Geodetic and Seismic Analysis of the effects of Englacial and Subglacial Hydraulics on Surface Crevassing near a Seasonal, Glacier-Dammed Lake on Gornergletscher, Switzerland

NASA Astrophysics Data System (ADS)

Garcia, L.; Luttrell, K. M.; Kilb, D. L.; Walter, F.

2017-12-01

Glacial outburst floods are difficult to predict and threaten human life and property near glaciated regions. These events are characterized by rapid draining of glacier-dammed lakes via the sub/englacial hydraulic network to the proglacial stream. The glacier-dammed lake on Gornergletscher in Switzerland, which fills and drains each summer, provides an opportunity to study this hazard. For three drainages (2004, 2006, and 2007), we track icequakes (IQ) and on-ice GPS movement. Our seasonal seismic networks had 8 - 24 three component stations and apertures of about 300 - 400 m on the glacier surface. The seasonal GPS arrays contained 4 - 8 GPS antennae on the glacier surface. Using Rayleigh wave coherence surface IQ location, we located 2924, 7822 and 3782 IQs, in 2004, 2006 and 2007, respectively. The GPS data were smoothed using a nonparametric protocol, with average station velocities of 10 - 90 mm/day. In 2006, strains were calculated using five stations within 500 m of the lake, co-located with the seismic network. IQ productivity increased substantially during lake drainage only in 2004, which was the only year when the lake drainage was rapid ( 6 days) and primarily subglacial. In 2006, there was no obvious increase in GPS speeds with slow ( 21 days), supraglacial lake drainage. However, when drainage was subglacial as in 2004 and 2007 (sub/englacial over 11 days), GPS speed increased up to 160%. This speed increase is evidence for basal sliding induced by subglacial drainage. In general, we find that when the strain increase on the principle extension axis aligns with the crevasse opening direction, IQ are more prolific. We also observe a diurnal signal in both IQ occurrence and surface strain, with peak strain occurring in the mid- to late-afternoon (15:00 - 19:00 local) across the study area in 2006. We interpret this time-shift in strain and spatiotemporal dependence of IQs to be caused by diurnal variations in melt-induced sliding. Our analysis sheds light on crevasse formation on short time scales where glacier flow is controlled by sliding variations in response to water input into the subglacial drainage system. Coupled seismic and GPS monitoring can thus make a key contribution to our understanding of brittle deformation and crevassing of glacier ice.

Global geodesy using GPS without fiducial sites

NASA Technical Reports Server (NTRS)

Heflin, Michael; Bertiger, Willy; Blewitt, Geoff; Freedman, Adam; Hurst, Ken; Lichten, Steve; Lindqwister, Ulf; Vigue, Yvonne; Webb, Frank; Yunck, Tom

1992-01-01

Baseline lengths and geocentric radii have been determined from GPS data without the use of fiducial sites. Data from the first GPS experiment for the IERS and Geodynamics (GIG '91) have been analyzed with a no-fiducial strategy. A baseline length daily repeatability of 2 mm + 4 parts per billion was obtained for baselines in the Northern Hemisphere. Comparison of baseline lengths from GPS and the global VLBI solution GLB659 (Caprette et al. 1990) show rms agreement of 2.1 parts per billion. The geocentric radius mean daily repeatability for all sites was 15 cm. Comparison of geocentric radii from GPS and SV5 (Murray et al. 1990) show rms agreement of 3.8 cm. Given n globally distributed stations, the n(n - 1)/2 baseline lengths and n geocentric radii uniquely define a rigid closed polyhedron with a well-defined center of mass. Geodetic information can be obtained by examining the structure of the polyhedron and its change with time.

(abstract) Altimeter Calibration and Geophysical Monitoring from Collocated Measurements at the Harvest Oil Platform

NASA Technical Reports Server (NTRS)

Haines, B. J.; Christensen, E. J.; Norman, R. A.; Parke, M. E.; Born, G. H.; Gill, S. K.

1996-01-01

Prior to the launch of TOPEX/ Poseidon in August 1992, NASA established its primary in situ verification site on the Harvest oil platform located in the Pacific Ocean off the coast of central California. Data from a suite of geodetic and oceanographic instruments attached to the platform have been combined to yield a precise record of absolute sea level simce the beginning of the mission. Critical to the computation of this geocentric sea level record is the precise determination of the platform geodetic height and the vertical velocity in the global terrestrial reference frame.We compare estimates of the platform height and vertical velocity from global positioning system (GPS) data alone and from a combination of GPS and satellite laser ranging (SLR) information. Current estimates suggest the platform is subsiding at a rate of about 8 mm per year. This height information is combined with in situ tide gauge measurements of sea level relative to a platform reference mark in order to produce a continuous record of the local geocentric sea height.

Analysis of Site Position Time Series Derived From Space Geodetic Solutions

NASA Astrophysics Data System (ADS)

Angermann, D.; Meisel, B.; Kruegel, M.; Tesmer, V.; Miller, R.; Drewes, H.

2003-12-01

This presentation deals with the analysis of station coordinate time series obtained from VLBI, SLR, GPS and DORIS solutions. We also present time series for the origin and scale derived from these solutions and discuss their contribution to the realization of the terrestrial reference frame. For these investigations we used SLR and VLBI solutions computed at DGFI with the software systems DOGS (SLR) and OCCAM (VLBI). The GPS and DORIS time series were obtained from weekly station coordinates solutions provided by the IGS, and from the joint DORIS analysis center (IGN-JPL). We analysed the time series with respect to various aspects, such as non-linear motions, periodic signals and systematic differences (biases). A major focus is on a comparison of the results at co-location sites in order to identify technique- and/or solution related problems. This may also help to separate and quantify possible effects, and to understand the origin of still existing discrepancies. Technique-related systematic effects (biases) should be reduced to the highest possible extent, before using the space geodetic solutions for a geophysical interpretation of seasonal signals in site position time series.

Α Deformation study in Central Greece using 20 years of GPS data

NASA Astrophysics Data System (ADS)

Marinou, Aggeliki; Papazissi, Kaliopi; Mitsakaki, Christiana; Paradissis, Demitris; Papanikolaou, Xanthos; Anastasiou, Demitris

2015-04-01

Central Greece is a region recognized for its intense tectonic activity with the main characterics being the extension in the North-South direction. This extension is revealed mainly in the form of large parallel grabens. Among these rifts is the Corinth Gulf, which is the most active tectonically, the basin between Parnassos and Kallidromo Mt, the Locris basin and the graben of North Evoikos Gulf, while in the south lays the Thebes basin and the South Evoikos Gulf. Since the late eighties the Laboratory of Higher Geodesy and the Dionysos Satellite Observatory of the National Technical University of Athens, in cooperation with several National and International Universities and Institutions have established, in various Greek areas, of high seismic activity, geodetic networks in order to monitor tectonic displacements. These geodetic networks were observed periodically using Satellite Geodesy techniques and in recent years almost entirely GPS. In this study all the available GPS data, referring to the broader area of Evia, Attiki and Viotia, for the years 1989 to 2008, are analyzed. The displacement field and its temporal changes for the area between the two major geological features, the Corinth Gulf and the Evoikos Gulf, are investigated. Αll the kinematic models that were used do not confirm that the area of study is deforming homogeneously, while an indication of a discontinuity has been detected.

Field Installation and Real-Time Data Processing of the New Integrated SeismoGeodetic System with Real-Time Acceleration and Displacement Measurements for Earthquake Characterization Based on High-Rate Seismic and GPS Data

NASA Astrophysics Data System (ADS)

Zimakov, Leonid; Jackson, Michael; Passmore, Paul; Raczka, Jared; Alvarez, Marcos; Barrientos, Sergio

2015-04-01

We will discuss and show the results obtained from an integrated SeismoGeodetic System, model SG160-09, installed in the Chilean National Network. The SG160-09 provides the user high rate GNSS and accelerometer data, full epoch-by-epoch measurement integrity and, using the Trimble Pivot™ SeismoGeodetic App, the ability to create combined GNSS and accelerometer high-rate (200Hz) displacement time series in real-time. The SG160-09 combines seismic recording with GNSS geodetic measurement in a single compact, ruggedized package. The system includes a low-power, 220-channel GNSS receiver powered by the latest Trimble-precise Maxwell™6 technology and supports tracking GPS, GLONASS and Galileo signals. The receiver incorporates on-board GNSS point positioning using Real-Time Precise Point Positioning (PPP) technology with satellite clock and orbit corrections delivered over IP networks. The seismic recording element includes an ANSS Class A, force balance triaxial accelerometer with the latest, low power, 24-bit A/D converter, which produces high-resolution seismic data. The SG160-09 processor acquires and packetizes both seismic and geodetic data and transmits it to the central station using an advanced, error-correction protocol with back fill capability providing data integrity between the field and the processing center. The SG160-09 has been installed in the seismic station close to the area of the Iquique earthquake of April 1, 2014, in northern Chile, a seismically prone area at the current time. The hardware includes the SG160-09 system, external Zephyr Geodetic-2 GNSS antenna, and high-speed Internet communication media. Both acceleration and displacement data was transmitted in real-time to the National Seismological Center in Santiago for real-time data processing using Earthworm / Early Bird software. Command/Control of the field station and real-time GNSS position correction are provided via the Pivot software suite. Data from the SG160-09 system was used for seismic event characterization along with data from traditional stand-alone broadband seismic and geodetic stations installed in the network. Our presentation will focus on the key improvements of the network installation with the SG160-09 system, rapid data transmission, and real-time data processing for strong seismic events and aftershock characterization as well as advanced features of the SG160-09 for Earthquake and Tsunami Early Warning system.

Gnss Geodetic Monitoring as Support of Geodynamics Research in Colombia, South America

NASA Astrophysics Data System (ADS)

Mora-Paez, H.; Acero-Patino, N.; Rodriguez-Zuluaga, J. S.; Diederix, H.; Bohorquez-Orozco, O. P.; Martinez-Diaz, G. P.; Diaz-Mila, F.; Giraldo-Londono, L. S.; Cardozo-Giraldo, S.; Vasquez-Ospina, A. F.; Lizarazo, S. C.

2013-05-01

To support the geodynamics research at the northwestern corner of South America, GEORED, the acronym for "Geodesia: Red de Estudios de Deformación" has been adopted for the Project "Implementation of the National GNSS Network for Geodynamics" carried out by the Colombian Geological Survey, (SGC), formerly INGEOMINAS. Beginning in 2007, discussions within the GEORED group led to a master plan for the distribution of the base permanent GPS/GNSS station array and specific areas of interest for campaign site construction. The use of previously identified active faults as preferred structures along which stresses are transferred through the deformational area led to the idea of segmentation of the North Andes within Colombia into 20 tectonic sub-blocks. Each of the 20 sub-blocks is expected to have, at least, three-four permanent GPS/GNSS stations within the block along with construction of campaign sites along the boundaries. Currently, the GEORED Network is managing 46 continuously including: 40 GEORED GPS/GNSS continuously operating stations; 4 GNSS continuously operating stations provided by the COCONet (Continuously Operating Caribbean GPS Observational Network) Project; the Bogotá IGS GPS station (BOGT), installed in 1994 under the agreement between JPL-NASA and the SGC; and the San Andres Island station, installed in 2007 under the MOU between UCAR and the SGC. In addition to the permanent installations, more than 230 GPS campaign sites have been constructed and are being occupied one time per year. The Authority of the Panama Canal and the Escuela Politecnica de Quito have also provided data of 4 and 5 GPS/GNSS stations respectively. The GPS data are processed using the GIPSY-OASIS II software, and the GPS time series of daily station positions give fundamental information for both regional and local geodynamics studies. Until now, we have obtained 100 quality vector velocities for Colombia, 23 of them as part of the permanent network. The GPS/GNSS stations are located on the three major plates that interact within the Wide Plate Margin Deformation Zone including existing permanent installations on IGS Galapagos and Malpelo Islands on the Nazca Plate, and San Andres Island on the Caribbean plate. The velocity vectors confirm the oblique subduction of the Nazca Plate and Carnegie aseismic ridge collision processes at the Colombia-Ecuador trench which are assumed to be the mechanism for the transpressional deformation and the "escape" of the North Andes Block (NAB). The northernmost vectors in Colombia are indicative of the ongoing collision of the Panama Arc with northwestern Colombia. Planned for the year 2013 is the installation of 10 additional GNSS continuously operating stations, and construction of 20 GPS campaign sites.

RTX Correction Accuracy and Real-Time Data Processing of the New Integrated SeismoGeodetic System with Real-Time Acceleration and Displacement Measurements for Earthquake Characterization Based on High-Rate Seismic and GPS Data

NASA Astrophysics Data System (ADS)

Zimakov, L. G.; Raczka, J.; Barrientos, S. E.

2016-12-01

We will discuss and show the results obtained from an integrated SeismoGeodetic System, model SG160-09, installed in the Chile (Chilean National Network), Italy (University of Naples Network), and California. The SG160-09 provides the user high rate GNSS and accelerometer data, full epoch-by-epoch measurement integrity and the ability to create combined GNSS and accelerometer high-rate (200Hz) displacement time series in real-time. The SG160-09 combines seismic recording with GNSS geodetic measurement in a single compact, ruggedized case. The system includes a low-power, 220-channel GNSS receiver powered by the latest Trimble-precise Maxwell™6 technology and supports tracking GPS, GLONASS and Galileo signals. The receiver incorporates on-board GNSS point positioning using Real-Time Precise Point Positioning (PPP) technology with satellite clock and orbit corrections delivered over IP networks. The seismic recording includes an ANSS Class A, force balance accelerometer with the latest, low power, 24-bit A/D converter, producing high-resolution seismic data. The SG160-09 processor acquires and packetizes both seismic and geodetic data and transmits it to the central station using an advanced, error-correction protocol providing data integrity between the field and the processing center. The SG160-09 has been installed in three seismic stations in different geographic locations with different Trimble global reference stations coverage The hardware includes the SG160-09 system, external Zephyr Geodetic-2 GNSS antenna, both radio and high-speed Internet communication media. Both acceleration and displacement data was transmitted in real-time to the centralized Data Acquisition Centers for real-time data processing. Command/Control of the field station and real-time GNSS position correction are provided via the Pivot platform. Data from the SG160-09 system was used for seismic event characterization along with data from traditional seismic and geodetic stations installed in the network. Our presentation will focus on the key improvements of the network installation with the SG160-09 system, RTX correction accuracy obtained from Trimble Global RTX tracking network, rapid data transmission, and real-time data processing for strong seismic events and aftershock characterization.

Rip current monitoring using GPS buoy system

NASA Astrophysics Data System (ADS)

Song, DongSeob; Kim, InHo; Kang, DongSoo

2014-05-01

The occurrence of rip current in the Haeundae beach, which is one of the most famous beaches in South Korea, has been threatening beach-goers security in summer season annually. Many coastal scientists have been investigating rip currents by using field observations and measurements, laboratory measurements and wave tank experiments, and computer and numerical modeling. Rip current velocity is intermittent and may rapidly increase within minutes due to larger incoming wave groups or nearshore circulation instabilities. It is important to understand that changes in rip current velocity occur in response to changes in incoming wave height and period as well as changes in water level. GPS buoys have been used to acquire sea level change data, atmospheric parameters and other oceanic variables in sea for the purposes of vertical datum determination, tide correction, radar altimeter calibration, ocean environment and marine pollution monitoring. Therefore, we adopted GPS buoy system for an experiment which is to investigate rip current velocity; it is sporadic and may quickly upsurge within minutes due to larger arriving wave groups or nearshore flow uncertainties. In this study, for high accurate positioning of buy equipment, a Satellite Based Argumentation System DGPS data logger was deployed to investigate within floating object, and it can be acquired three-dimensional coordinate or geodetic position of buoy with continuous NMEA-0183 protocol during 24 hours. The wave height measured by in-situ hydrometer in a cross-shore array clearly increased before and after occurrence of rip current, and wave period also was lengthened around an event. These results show that wave height and period correlate reasonably well with long-shore current interaction in the Haeundae beach. Additionally, current meter data and GPS buoy data showed that rip current velocities, about 0.2 m/s, may become dangerously strong under specific conditions. Acknowledgement This research was supported by Basic Science Research Program through the National Research Foundation of Korea(NRF) funded by the Ministry of Education, Science and Technology(2010-0024670)

Monitoring Sea Level by Tide Gauges and GPS at Barcelona and Estartit Harbours

NASA Astrophysics Data System (ADS)

Martinez Benjamin, J. J.; Gili, J.; Lopez, R.; Tapia, A.; Bosch, E.; Perez, B.; Pros, F.

2012-04-01

Sea level is an environmental variable which is widely recognised as being important in many scientific disciplines as a control parameter for coastal dynamical processes or climate processes in the coupled atmosphere-ocean systems, as well as engineering applications. A major source of sea-level data are the national networks of coastal tide gauges, in Spain belonging to different institutions as the Instituto Geográfico Nacional (IGN), Puertos del Estado (PE), Instituto Hidrográfico de la Marina (IHM), etc. The tide gauge of l'Estartit is a traditional floating gauge placed 21 years ago and has an accuracy of ± 2 mm. Since 1996, l'Estartit tide gauge has been co-located with geodetic techniques (GPS measurements of XU, Utilitary Network, and XdA, Levelling Network,) and it is tied to the SPGIC (Integrated Geodetic Positioning System of Catalonia) project of the Cartographic Institute of Catalunya (ICC). In 2006, due to the work for the expansion of the harbour, the tide gauge had to be moved. Before the work started, appropiate GPS measurements were carried out in order to ensure the connection of the tide gauge data. During October 2006 and May 2008, the tide gauge was inactive and it has been moved on to a new location inside the harbour. In June 2008, new GPS and levelling measures have been done in order to tie the new location into SPGIC project and to co-locate old data respect the new one. Although l'Estartit does not have a GPS permanent station, it is possible to build a virtual one from the service "CATNET web" of the ICC. "CATNET web" is a data distribution system of a virtual GPS permanent station via web. From the coordinates where you want to place the virtual station, the time interval and the measurement rate, the system generates a RINEX file under the requested conditions. At Barcelona harbour there is one MIROS radar tide gauge belonging to Puertos del Estado (Spanish Harbours). It is placed at the dock 140 of the ENAGAS Building.The radar sensor is over the water surface, on a L-shaped structure which elevates it a few meters above the quay shelf. 1-min data are transmitted to the ENAGAS Control Center by cable and then sent each 1 min to Puertos del Estado by e-mail.This sensor also measures agitation and sends wave parameters each 20 min. A provisional tide gauge bench mark has been defined while the levelling has being done. There is a GPS station Leica Geosystems GRX1200 GG Pro and antenna 1202. Bathymetric campaigns inside the harbour have been made. The presentation is directed to the description of the actual situation of the geodetic infrastructure of Barcelona and l'Estartit sites for sea level determination and contribution to regional sea level rise.

Plate Motion and Crustal Deformation Estimated with Geodetic Data from the Global Positioning System

NASA Technical Reports Server (NTRS)

Argus, Donald F.; Heflin, Michael B.

1995-01-01

We use geodetic data taken over four years with the Global Positioning System (GPS) to estimate: (1) motion between six major plates and (2) motion relative to these plates of ten sites in plate boundary zones. The degree of consistency between geodetic velocities and rigid plates requires the (one-dimensional) standard errors in horizontal velocities to be approx. 2 mm/yr. Each of the 15 angular velocities describing motion between plate pairs that we estimate with GPS differs insignificantly from the corresponding angular velocity in global plate motion model NUVEL-1A, which averages motion over the past 3 m.y. The motion of the Pacific plate relative to both the Eurasian and North American plates is observed to be faster than predicted by NUVEL-1A, supporting the inference from Very Long B ase- line Interferometry (VLBI) that motion of the Pacific plate has speed up over the past few m.y. The Eurasia-North America pole of rotation is estimated to be north of NUVEL-1A, consistent with the independent hypothesis that the pole has recently migrated northward across northeast Asia to near the Lena River delta. Victoria, which lies above the main thrust at the Cascadia subduction zone, moves relative to the interior of the overriding plate at 30% of the velocity of the subducting plate, reinforcing the conclusion that the thrust there is locked beneath the continental shelf and slope.

Volcano geodesy in the Cascade arc, USA

NASA Astrophysics Data System (ADS)

Poland, Michael P.; Lisowski, Michael; Dzurisin, Daniel; Kramer, Rebecca; McLay, Megan; Pauk, Ben

2017-08-01

Experience during historical time throughout the Cascade arc and the lack of deep-seated deformation prior to the two most recent eruptions of Mount St. Helens might lead one to infer that Cascade volcanoes are generally quiescent and, specifically, show no signs of geodetic change until they are about to erupt. Several decades of geodetic data, however, tell a different story. Ground- and space-based deformation studies have identified surface displacements at five of the 13 major Cascade arc volcanoes that lie in the USA (Mount Baker, Mount St. Helens, South Sister, Medicine Lake, and Lassen volcanic center). No deformation has been detected at five volcanoes (Mount Rainier, Mount Hood, Newberry Volcano, Crater Lake, and Mount Shasta), and there are not sufficient data at the remaining three (Glacier Peak, Mount Adams, and Mount Jefferson) for a rigorous assessment. In addition, gravity change has been measured at two of the three locations where surveys have been repeated (Mount St. Helens and Mount Baker show changes, while South Sister does not). Broad deformation patterns associated with heavily forested and ice-clad Cascade volcanoes are generally characterized by low displacement rates, in the range of millimeters to a few centimeters per year, and are overprinted by larger tectonic motions of several centimeters per year. Continuous GPS is therefore the best means of tracking temporal changes in deformation of Cascade volcanoes and also for characterizing tectonic signals so that they may be distinguished from volcanic sources. Better spatial resolution of volcano deformation can be obtained through the use of campaign GPS, semipermanent GPS, and interferometric synthetic aperture radar observations, which leverage the accumulation of displacements over time to improve signal to noise. Deformation source mechanisms in the Cascades are diverse and include magma accumulation and withdrawal, post-emplacement cooling of recent volcanic deposits, magmatic-tectonic interactions, and loss of volatiles plus densification of magma. The Cascade Range thus offers an outstanding opportunity for investigating a wide range of volcanic processes. Indeed, there may be areas of geodetic change that have yet to be discovered, and there is good potential for addressing a number of important questions about how arc volcanoes work before, during, and after eruptions by continuing geodetic research in the Cascade Range.

Volcano geodesy in the Cascade arc, USA

USGS Publications Warehouse

Poland, Michael; Lisowski, Michael; Dzurisin, Daniel; Kramer, Rebecca; McLay, Megan; Pauk, Benjamin

2017-01-01

Experience during historical time throughout the Cascade arc and the lack of deep-seated deformation prior to the two most recent eruptions of Mount St. Helens might lead one to infer that Cascade volcanoes are generally quiescent and, specifically, show no signs of geodetic change until they are about to erupt. Several decades of geodetic data, however, tell a different story. Ground- and space-based deformation studies have identified surface displacements at five of the 13 major Cascade arc volcanoes that lie in the USA (Mount Baker, Mount St. Helens, South Sister, Medicine Lake, and Lassen volcanic center). No deformation has been detected at five volcanoes (Mount Rainier, Mount Hood, Newberry Volcano, Crater Lake, and Mount Shasta), and there are not sufficient data at the remaining three (Glacier Peak, Mount Adams, and Mount Jefferson) for a rigorous assessment. In addition, gravity change has been measured at two of the three locations where surveys have been repeated (Mount St. Helens and Mount Baker show changes, while South Sister does not). Broad deformation patterns associated with heavily forested and ice-clad Cascade volcanoes are generally characterized by low displacement rates, in the range of millimeters to a few centimeters per year, and are overprinted by larger tectonic motions of several centimeters per year. Continuous GPS is therefore the best means of tracking temporal changes in deformation of Cascade volcanoes and also for characterizing tectonic signals so that they may be distinguished from volcanic sources. Better spatial resolution of volcano deformation can be obtained through the use of campaign GPS, semipermanent GPS, and interferometric synthetic aperture radar observations, which leverage the accumulation of displacements over time to improve signal to noise. Deformation source mechanisms in the Cascades are diverse and include magma accumulation and withdrawal, post-emplacement cooling of recent volcanic deposits, magmatic-tectonic interactions, and loss of volatiles plus densification of magma. The Cascade Range thus offers an outstanding opportunity for investigating a wide range of volcanic processes. Indeed, there may be areas of geodetic change that have yet to be discovered, and there is good potential for addressing a number of important questions about how arc volcanoes work before, during, and after eruptions by continuing geodetic research in the Cascade Range.

A GPS Modeling Study of Earthquakes and Deformation in Northern Central America and along the Middle America Trench: 1999 to 2017

NASA Astrophysics Data System (ADS)

Ellis, Andria P.

Northern Central America is a tectonically complicated region prone to hazardous earthquakes due to the confluence of the Motagua-Polochic fault zone with the Middle America trench and strike-slip faults in the Central America volcanic arc. These three major fault zones converge at the western end of the Caribbean plate where the Cocos plate subducts under the North America and Caribbean plates. Literature from the 1970s and 1980s focused on whether a discrete North America-Caribbean-Cocos plate triple junction existed, and how the relative motions of the upper North America and Caribbean plates were accommodated. The discovery of a fourth major crustal block, the Central America forearc sliver, from seismic and geodetic observations made a three-plate triple junction geometrically impossible and introduced a new set of questions related to how deformation of the upper plate accommodates relative movements between the Caribbean plate, North America plate, and Central America forearc sliver where they intersect in the upper plate. My dissertation uses GPS and numerical modeling to measure and quantify earthquake transients and crustal deformation related to fault interactions in northern Central America and consists of three related chapters. The first chapter of my dissertation is a geodetic study of a M w = 7.4 subduction zone earthquake that occurred in 2012 offshore from our Guatemala GPS (Global Positioning System) network. For this study, I inverted coseismic site offsets and postseismic amplitudes to determine best-fitting coseismic and afterslip rupture distributions on the Middle America trench. I also determined the maximum likely viscoelastic deformation for the earthquake to test whether the transient postseismic deformation was dominated by fault afterslip or viscoelastic flow. This work was published in Geophysical Journal International in January 2015. The second chapter of my dissertation derives a new 200+ site GPS velocity field for northern Central America. Doing so was complicated by the occurrence of four M > 7 earthquakes since 2009, which perturbed the velocities of many of the GPS sites. To extract the interseismic velocity field from position time-series, we use TDEFNODE software to simultaneously model source parameters for coseismic rupture and transient afterslip from the 2012 El Salvador (M w = 7.3), 2012 Guatemala (Mw = 7.4), and 2009 Swan Islands (Mw = 7.3) earthquakes. The resulting, corrected best-fitting GPS site velocities are used in my third and final chapter. Finally, I address a variety of questions regarding several major faults that are the root of natural hazard studies in northern Central America. The 200+ site GPS velocity field derived in Chapter 2 far exceeds any previous velocity field for this region and represents a new standard for studying the tectonics of northern Central America. An inversion of the new velocity field using an eight-block elastic model gives the following unique or improved results with respect to previous work: 1) First evidence for a nearly rigid Chortis block south of the Motagua fault; 2) Evidence for southward transfer of slip from the western Motagua fault into the Guatemala City graben and other nearby normal faults; 3) A well-bounded estimate on partitioning of plate boundary slip on the Motagua and Polochic faults; 4) A first plate tectonic estimate of Cocos plate subduction below the Central America forearc sliver; 5) The first geodetic estimate of slip rate variations along the Central America volcanic arc, including the first slip rate estimate for the poorly-understood Jalpatagua fault in southern Guatemala; 6) The first geodetic estimate of distributed deformation in the Chiapas Tectonic Province; 7) Evidence for stronger locking offshore southern Mexico and even weaker shallow locking offshore Guatemala and El Salvador than previously estimated; 8) A refined estimate of how extension is distributed across the grabens of western Honduras and southern Guatemala; 9) Strain-rate tensors consistent with no significant deformation of the elongate Central America forearc sliver, but extension within the Gulf of Fonseca step-over in the Central America volcanic arc; 10) Evidence for slower slip along the Motagua fault than any previous estimate and a well-determined geodetic estimate for the long-term slip rate of the Polochic fault.

Fracture and slope stability monitoring at Puigcercós landslide (Catalonia, Spain)

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Vasquez, Sebastian; López, Robert; Guinau, Guinau; Calvet, Jaume; Vilaplana, Joan Manuel; Blanch, Xabier; Tapia, Mar; Roig, Pere; Suriñach, Emma

2017-04-01

The village of Puigcercós ( 50 inhabitants) is located in the region of Pallars Jussà (Lleida) in Catalonia, several km south of the town of Tremp. In 1881 the entire village had to be moved from its historical location on top of the hill to its current location. This was caused by a series of landslides caused by continuing rainfall. The most important landslide occurred on January 13th 1881, which displaced more than 5 million cubic meters of sediments and rocks and created an impressive rock scar of approximately 25 m height and 150 m width. The area where the sediments were accumulated is extensive, reaching 8 hectares. During the last years, our group has chosen the site of Puigcercós to conduct pilot studies of landslides and rockfalls using multidisciplinary approach, involving Terrestrial Laser Scanner, Total Station, DGPS, seismic monitoring and geophysical techniques. The geophysical surveys of the zone of the sediment accumulation, can help determine the internal structure of the displaced sediments. The work presented here mainly concerns the deformation monitoring at the site using geodetic techniques. In July 2015, a network of 11 new geodetic points has been established and measured with GPS. The location of these points was chosen with the purpose of answering two important questions in the studies of the stability and geomorphological activity of the Puigcercós landslide: 1) As a result of combined analysis of the tape-meter, total station and GPS measurements, we hope to obtain absolute values of deformation in the upper part of the escarpment, controlling the stability of the escarpment front and the associated fractures near the coronation. For this purpose, two geodetic control points have been established at the hilltop, some 5 meters away from the escarpment itself. 2) Determine the slope stability of the depositional area, where we established nine geodetic points. As of today, these points have been measured twice, in 2015 and 2016, during 24 hour long campaigns, overlapping a midnight. Thus, obtained GPS observations cover at least 8 hours for 2 consecutive days, ensuring the millimeter level accuracy after the post-processing using GAMIT/GLOBK software from MIT. After the realization of the third campaign in the spring of 2017, we hope to give more definitive answers to the questions raised above. This work is conducted within the framework of the project CHARMA (CGL2013-40828-R), financed by the Ministry of Economy, Industry and Competitiveness of Spain. We are thankful to the students who participated in the GPS campaigns: E. Bravo, M. Galindos, Ciscu Sánchez.

Towards a Refined Realisation of the Terrestrial Reference System

NASA Astrophysics Data System (ADS)

Angermann, D.; Drewes, H.; Meisel, B.; Kruegel, M.; Tesmer, V.

2004-12-01

Global reference frames provide the framework for scientific investigations of the Earth's system (e.g. plate tectonics, sea level change, seasonal and secular loading signals, atmosphere dynamics, Earth orientation excitation), as well as for many practical applications (e.g. surveying and navigation). Today, space geodetic techniques allow to determine geodetic parameters (e.g. station positions, Earth rotation) with a precision of a few millimeters (or even better). However, this high accuracy is not reflected by current realisations of the terrestrial reference system. To fully exploit the potential of the space geodetic observations for investigations of various global and regional, short-term, seasonal and secular phenomena of the Earth's system, the reference frame must be realised with the highest accuracy, spatial and temporal consistency and stability over decades. Furthermore, future progress in Earth sciences will fundamentally depend on understanding the Earth as a system, into which the three areas of geodetic research (geometry/deformation, Earth rotation, gravity) are to be integrated. The presentation focusses on various aspects that must be considered for a refined realisation of the terrestrial reference system, such as the development of suitable methods for the combination of the contributing space geodetic observations, the realisation of the TRF datum and the parameterisation of site motions. For this purpose we investigated time series of station positions and datum parameters obtained from VLBI, SLR, GPS and DORIS solutions, and compared the results at co-location sites and with other studies. Furthermore, we present results obtained from a TRS realisation based on epoch (weekly/daily) normal equations with station positions and daily Earth Orientation Parameters (EOP) using five years (1999-2004) of VLBI, SLR, GPS and DORIS data. This refined approach has major advantages compared to past TRF realisations based on multi-year solutions with station positions at a given epoch and constant velocities, as for instance non-linear effects of site positions and datum parameters can be considered, and consistency between TRF and EOPs can be achieved. First results of this new approach are promising.

The Plate Boundary Observatory: Current status and plans for the next five years

NASA Astrophysics Data System (ADS)

Mattioli, G. S.; Feaux, K.; Meertens, C. M.; Mencin, D.; Miller, M.

2013-12-01

UNAVCO currently operates and maintains the NSF-funded Plate Boundary Observatory (PBO), which is the geodetic facility of EarthScope. PBO was designed and built from 2003 to 2008 with $100M investment from the NSF Major Research Equipment and Facilities Construction (MREFC) Program. UNAVCO operated and maintained PBO under a Cooperative Agreement (CA) with NSF from 2008 to 2013 and will continue PBO O&M for the next five years as part of the new Geodesy Advancing Geosciences and EarthScope (GAGE) Facility. PBO is largest continuous GPS and borehole geophysical network in the Americas, with 1100 continuous Global Positioning System (cGPS) sites, including several with multiple monuments, 79 boreholes, with 75 tensor strainmeters, 78 short-period, 3-component seismometers, and pore pressure sensors at 23 sites. PBO also includes 26 tiltmeters deployed at volcanoes in Alaska, Mt St Helens, and Yellowstone caldera and 6 long-baseline laser strainmeters. Surface meteorological sensors are collocated at 154 GPS sites. UNAVCO provides high-rate (1 Hz), low-latency (<1 s) GPS data streams (RT-GPS) from 382 stations in PBO. UNAVCO has delivered over 62 Tb of geodetic data to the EarthScope community since its PBO's inception in 2004. Over the past year, data return for the cGPS component of PBO is 98%, well above the data return metric of 85% set by the NSF, a result of efforts to upgrade power systems and communications infrastructure. In addition, PBO has set the standard for the design, construction, and operation of other multi-hazard networks across the Americas, including COCONet in the Caribbean region and TLALOCNet in Mexico. Funding to support ongoing PBO O&M has declined from FY2012 CA levels under the new GAGE Facility. The implications for data return and data quality metrics as well as replacement of aging PBO GPS instruments with GNSS-compatible systems are as yet unknown. A process to assess the cost of specific PBO components, data rates, enhanced capabilities, and method of delivery (i.e. continuous streams vs. archived files) relative to their scientific value will be proposed. In addition, options to partner with other federal mission-oriented agencies and possible commercial ventures also will be discussed. 1100 station PBO continuous GPS Network.

LiDAR and Image Point Cloud Comparison

DTIC Science & Technology

2014-09-01

UAV unmanned aerial vehicle USGS United States Geological Survey UTM Universal Transverse Mercator WGS 84 World Geodetic System 1984 WSI...19  1.  Physics of LiDAR Systems ................................................................20  III.  DATA AND SOFTWARE...ground control point GPS Global Positioning System IMU inertial measurements unit LiDAR light detection and ranging MI mutual information MVS

Co-seismic deformation of the August 27, 2012 Mw 7.3 El Salvador and September 5, 2012 Mw 7.6 Costa Rica earthquakes

NASA Astrophysics Data System (ADS)

Geirsson, H.; La Femina, P. C.; DeMets, C.; Mattioli, G. S.; Hernández, D.

2013-05-01

We investigate the co-seismic deformation of two significant earthquakes that occurred along the Middle America trench in 2012. The August 27 Mw 7.3 El Salvador and September 5 Mw 7.6 Nicoya Peninsula, Costa Rica earthquakes, were examined using a combination of episodic and continuous Global Positioning System (GPS) data. USGS finite fault models based on seismic data predict fundamentally different characteristics for the two ruptures. The El Salvador event occurred in a historical seismic gap and on the shallow segment of the Middle America Trench main thrust, rupturing a large area, but with a low magnitude of slip. A small tsunami was observed along the coast in Nicaragua and El Salvador, additionally indicating near-trench rupture. Conversely, the Nicoya, Costa Rica earthquake was predicted to have an order of magnitude higher slip on a spatially smaller patch deeper on the main thrust. We present results from episodic and continuous geodetic GPS measurements made in conjunction with the two earthquakes, including data from newly installed COCONet (Continuously Operating Caribbean GPS Observational Network) sites. Episodic GPS measurements made in El Salvador, Honduras, and Nicaragua following the earthquakes, allow us to estimate the co-seismic deformation field from both earthquakes. Because of the small magnitude of the El Salvador earthquake and its shallow rupture the observed co-seismic deformation is small (<2 cm). Conversely, the Costa Rica earthquake occurred directly beneath a seismic and geodetic network specifically designed to capture such events. The observed displacements exceeded 0.5 m and there is a significant post-seismic transient following the earthquake. We use our estimated co-seismic offsets for both earthquakes to model the magnitude and spatial variability of slip for these two events.

Geodetic constraints on continental rifting along the Red Sea

NASA Astrophysics Data System (ADS)

Reilinger, R.; McClusky, S.; Arrajehi, A.; Mahmoud, S.; Rayan, A.; Ghebreab, W.; Ogubazghi, G.; Al-Aydrus, A.

2006-12-01

We are using the Global Positioning System (GPS) to monitor and quantify patterns and rates of tectonic and magmatic deformation associated with active rifting of the continental lithosphere and the transition to sea floor spreading in the Red Sea. Broad-scale motions of the Nubian and Arabian plates indicate coherent plate motion with internal deformation below the current resolution of our measurements (~ 1-2 mm/yr). The GPS-determined Euler vector for Arabia-Nubia is indistinguishable from the geologic Euler vector determined from marine magnetic anomalies, and Arabia-Eurasia relative motion from GPS is equal within uncertainties to relative motion determined from plate reconstructions, suggesting that Arabia plate motion has remained constant (±10%) during at least the past ~10 Ma. The approximate agreement between broad-scale GPS rates of extension (i.e., determined from relative plate motions) and those determined from magnetic anomalies along the Red Sea rift implies that spreading in the central Red Sea is primarily confined to the central rift (±10-20%). Extension appears to be more broadly distributed in the N Red Sea and Gulf of Suez where comparisons with geologic data also indicate a relatively recent (between 500 and 125 kyr BP) change in the motion of the Sinai block that is distinct from both Nubia and Arabia. In the southern Red Sea, GPS results are beginning to define the motion of the "Danakil micro-plate". We investigate and report on a model involving CCW rotation of the Danakil micro-plate relative to Nubia and magmatic inflation below the Afar Triple Junction that is consistent with available geodetic constraints. Running the model back in time suggests that the Danakil micro-plate has been an integral part of rifting/triple junction processes throughout the history of separation of the Arabian and Nubian plates. On the scale of Nubia-Arabia-Eurasia plate interactions, we show that new area formed at spreading centers roughly equals that consumed at trenches, implying a dynamic connection between extension and subduction.

UNAVCO Geodetic HIgh-Rate and Real-Time Products and Services: A next generation geodetic network

NASA Astrophysics Data System (ADS)

Mattioli, G. S.; Mencin, D.; Meertens, C. M.; Feaux, K.; Looney, S.

2012-12-01

Recent advances in GPS technology and data processing are providing position estimates with centimeter-level precision at high-rate (1 Hz) and low latency (<1 s). These data will have the potential to improve our understanding in diverse areas of geophysics including properties of seismic, volcanic, magmatic and tsunami deformation sources, and moreover profoundly transforming rapid event characterization, early warning, as well as hazard mitigation and response. Other scientific and operational applications for high-rate GPS also include glacier and ice sheet motions, tropospheric modeling, and better constraints on the dynamics of space weather. UNAVCO, through community input and the recent Plate Boundary Observatory (PBO) NSF-ARRA Cascadia initiative, has nearly completed the process of upgrading a total of 373 PBO GPS sites to real-time high-rate capability and these streams are now being archived in our data center. In addition, UNAVCO hosted an NSF funded workshop in Boulder, CO on March 26-28, which brought together 70 participants representing a spectrum of research fields with a goal to develop a community plan for the use of real-time GPS data products within the UNAVCO and EarthScope communities. These data products are expected to improve and expand the use of real-time GPS data over the next decade. Additionally, in collaboration with NOAA, 74 of these stations will provide meteorological data in real-time, primarily to support watershed and flood analyses for regional early-warning systems related to NOAA's work with California Department of Water Resources. As part of this upgrade UNAVCO is also exploring making the 75 PBO borehole strainmeter sites, whose data are now collected with a latency of 24 hours, available in SEED format in real-time in the near future, providing an opportunity to combine high-rate surface positioning and strain data together.

GPS-Acoustic Seafloor Geodesy using a Wave Glider

NASA Astrophysics Data System (ADS)

Chadwell, C. D.

2013-12-01

The conventional approach to implement the GPS-Acoustic technique uses a ship or buoy for the interface between GPS and Acoustics. The high cost and limited availability of ships restricts occupations to infrequent campaign-style measurements. A new approach to address this problem uses a remote controlled, wave-powered sea surface vehicle, the Wave Glider. The Wave Glider uses sea-surface wave action for forward propulsion with both upward and downward motions producing forward thrust. It uses solar energy for power with solar panels charging the onboard 660 W-h battery for near continuous operation. It uses Iridium for communication providing command and control from shore plus status and user data via the satellite link. Given both the sea-surface wave action and solar energy are renewable, the vehicle can operate for extended periods (months) remotely. The vehicle can be launched from a small boat and can travel at ~ 1 kt to locations offshore. We have adapted a Wave Glider for seafloor geodesy by adding a dual frequency GPS receiver embedded in an Inertial Navigation Unit, a second GPS antenna/receiver to align the INU, and a high precision acoustic ranging system. We will report results of initial testing of the system conducted at SIO. In 2014, the new approach will be used for seafloor geodetic measurements of plate motion in the Cascadia Subduction Zone. The project is for a three-year effort to measure plate motion at three sites along an East-West profile at latitude 44.6 N, offshore Newport Oregon. One site will be located on the incoming plate to measure the present day convergence between the Juan de Fuca and North American plates and two additional sites will be located on the continental slope of NA to measure the elastic deformation due to stick-slip behavior on the mega-thrust fault. These new seafloor data will constrain existing models of slip behavior that presently are poorly constrained by land geodetic data 100 km from the deformation front.

High Frequency Variations in Earth Orientation Derived From GNSS Observations

NASA Astrophysics Data System (ADS)

Weber, R.; Englich, S.; Snajdrova, K.; Boehm, J.

2006-12-01

Current observations gained by the space geodetic techniques, especially VLBI, GPS and SLR, allow for the determination of Earth Orientation Parameters (EOPs - polar motion, UT1/LOD, nutation offsets) with unprecedented accuracy and temporal resolution. This presentation focuses on contributions to the EOP recovery provided by satellite navigation systems (primarily GPS). The IGS (International GNSS Service), for example, currently provides daily polar motion with an accuracy of less than 0.1mas and LOD estimates with an accuracy of a few microseconds. To study more rapid variations in polar motion and LOD we established in a first step a high resolution (hourly resolution) ERP-time series from GPS observation data of the IGS network covering the period from begin of 2005 till March 2006. The calculations were carried out by means of the Bernese GPS Software V5.0 considering observations from a subset of 79 fairly stable stations out of the IGb00 reference frame sites. From these ERP time series the amplitudes of the major diurnal and semidiurnal variations caused by ocean tides are estimated. After correcting the series for ocean tides the remaining geodetic observed excitation is compared with variations of atmospheric excitation (AAM). To study the sensitivity of the estimates with respect to the applied mapping function we applied both the widely used NMF (Niell Mapping Function) and the VMF1 (Vienna Mapping Function 1). In addition, based on computations covering two months in 2005, the potential improvement due to the use of additional GLONASS data will be discussed. Finally, satellite techniques are also able to provide nutation offset rates with respect to the most recent nutation model. Based on GPS observations from 2005 we established nutation rate time series and subsequently derived the amplitudes of several nutation waves with periods less than 30 days. The results are compared to VLBI estimates processed by means of the OCCAM 6.1 software.

First light from a kilometer-baseline Scintillation Auroral GPS Array.

PubMed

Datta-Barua, S; Su, Y; Deshpande, K; Miladinovich, D; Bust, G S; Hampton, D; Crowley, G

2015-05-28

We introduce and analyze the first data from an array of closely spaced Global Positioning System (GPS) scintillation receivers established in the auroral zone in late 2013 to measure spatial and temporal variations in L band signals at 100-1000 m and subsecond scales. The seven receivers of the Scintillation Auroral GPS Array (SAGA) are sited at Poker Flat Research Range, Alaska. The receivers produce 100 s scintillation indices and 100 Hz carrier phase and raw in-phase and quadrature-phase samples. SAGA is the largest existing array with baseline lengths of the ionospheric diffractive Fresnel scale at L band. With an initial array of five receivers, we identify a period of simultaneous amplitude and phase scintillation. We compare SAGA power and phase data with collocated 630.0 nm all-sky images of an auroral arc and incoherent scatter radar electron precipitation measurements, to illustrate how SAGA can be used in multi-instrument observations for subkilometer-scale studies. A seven-receiver Scintillation Auroral GPS Array (SAGA) is now at Poker Flat, Alaska SAGA is the largest subkilometer array to enable phase/irregularities studies Simultaneous scintillation, auroral arc, and electron precipitation are observed.

First light from a kilometer-baseline Scintillation Auroral GPS Array

PubMed Central

Datta-Barua, S; Su, Y; Deshpande, K; Miladinovich, D; Bust, G S; Hampton, D; Crowley, G

2015-01-01

We introduce and analyze the first data from an array of closely spaced Global Positioning System (GPS) scintillation receivers established in the auroral zone in late 2013 to measure spatial and temporal variations in L band signals at 100–1000 m and subsecond scales. The seven receivers of the Scintillation Auroral GPS Array (SAGA) are sited at Poker Flat Research Range, Alaska. The receivers produce 100 s scintillation indices and 100 Hz carrier phase and raw in-phase and quadrature-phase samples. SAGA is the largest existing array with baseline lengths of the ionospheric diffractive Fresnel scale at L band. With an initial array of five receivers, we identify a period of simultaneous amplitude and phase scintillation. We compare SAGA power and phase data with collocated 630.0 nm all-sky images of an auroral arc and incoherent scatter radar electron precipitation measurements, to illustrate how SAGA can be used in multi-instrument observations for subkilometer-scale studies. Key Points A seven-receiver Scintillation Auroral GPS Array (SAGA) is now at Poker Flat, Alaska SAGA is the largest subkilometer array to enable phase/irregularities studies Simultaneous scintillation, auroral arc, and electron precipitation are observed PMID:26709318

Implementation of CGPS at Estartit, Ibiza and Barcelona harbours for sea level monitoring

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J. J.; Ortiz Castellon, M.; Martinez-Garcia, M.; Perez, B.; Bosch, E.; Termens, A.; Martinez de Oses, X.

2009-12-01

The determination of global and regional mean sea level variations with accura-cies better than 1 mm/yr is a critical problem, the resolution of which is central to the current debate on climate change and its impact on the environment. Highly accurate time series from both satellite altimetry and tide gauges are needed. Measuring the sea surface height with in-situ tide gauges and GPS receivers pro-vides an efficient way to control the long term stability of the radar altimeters and other applications as the vertical land motion and studies of sea level change. L’Estartit tide gauge is a classical floating tide gauge set up in l’Estartit harbour (NE Spain) in 1990. Data are taken in graphics registers from which each two hours the mean value is recorded in an electronic support and delivered to the Permanent Service for Mean Sea level (PSMSL). Periodic surveying campaigns along the year are carried out for monitoring possible vertical movement of the geodetic benchmark adjacent to the tide gauge. Puertos del Estado (Spanish Harbours) installed the tide gauge station at Ibiza har-bour in January 2003 and a near GPS reference station. The station belongs to the REDMAR network, composed at this moment by 21 stations distributed along the whole Spanish waters, including also the Canary islands (http://www.puertos.es). The tide gauge also belongs to the ESEAS (European Sea Level) network. A description of the actual infrastructure at Ibiza, Barcelona and l’Estartit har-bours is presented.The main objective is the implementation of these harbours as a precise geodetic areas for sea level monitoring and altimeter calibration. Actually is a CGPS with a radar tide gauge from Puertos del Estado and a GPS belonging to Puerto de Barcelona. A precise levelling has been made by the Cartographic Insti-tute of Catalonia, ICC. The instrumentation of sea level measurements has been improved by providing the Barcelona site with a radar tide gauge Datamar 3000C device and a Thales Navigation Internet-Enabled GPS Continuous Geodetic Ref-erence Station (iCGRS) with a choke ring antenna, located at the EPSEB of the Technical University of Catalonia, UPC. It is intended that the overall system will constitute a CGPS Station of the ESEAS and TIGA networks.

Comparison of GPS and Quaternary slip rates: Insights from a new Quaternary fault database for Central Asia

NASA Astrophysics Data System (ADS)

Mohadjer, Solmaz; Ehlers, Todd; Bendick, Rebecca; Mutz, Sebastian

2016-04-01

Previous studies related to the kinematics of deformation within the India-Asia collision zone have relied on slip rate data for major active faults to test kinematic models that explain the deformation of the region. The slip rate data, however, are generally disputed for many of the first-order faults in the region (e.g., Altyn Tagh and Karakorum faults). Several studies have also challenged the common assumption that geodetic slip rates are representative of Quaternary slip rates. What has received little attention is the degree to which geodetic slip rates relate to Quaternary slip rates for active faults in the India-Asia collision zone. In this study, we utilize slip rate data from a new Quaternary fault database for Central Asia to determine the overall relationship between Quaternary and GPS-derived slip rates for 18 faults. The preliminary analysis investigating this relationship uses weighted least squares and a re-sampling analysis to test the sensitivity of this relationship to different data point attributes (e.g., faults associated with data points and dating methods used for estimating Quaternary slip rates). The resulting sample subsets of data points yield a maximum possible Pearson correlation coefficient of ~0.6, suggesting moderate correlation between Quaternary and GPS-derived slip rates for some faults (e.g., Kunlun and Longmen Shan faults). Faults with poorly correlated Quaternary and GPS-derived slip rates were identified and dating methods used for the Quaternary slip rates were examined. Results indicate that a poor correlation between Quaternary and GPS-derived slip rates exist for the Karakorum and Chaman faults. Large differences between Quaternary and GPS slip rates for these faults appear to be connected to qualitative dating of landforms used in the estimation of the Quaternary slip rates and errors in the geomorphic and structural reconstruction of offset landforms (e.g., offset terrace riser reconstructions for Altyn Tagh fault). Other factors such as a low density in the GPS network (e.g., GPS rate based on data from a single station for the Karakorum fault) appear to also contribute to the mismatch observed between the slip rates. Taken together, these results suggest that GPS-derived slip rates are often (but not always) representative of Quaternary slip rates and that the dating methods and sampling approaches used to identify transients in a fault slip rate history should be heavily scrutinized before interpreting the seismic hazards for a region.

Contemporary Deformation within the Snake River Plain and Northern Basin and Range Province, USA

NASA Astrophysics Data System (ADS)

Payne, S. J.; McCaffrey, R.; King, R. W.

2007-05-01

GPS velocities, earthquakes, faults, and volcanic features are used to evaluate contemporary deformation within the Snake River Plain (SRP) and surrounding northern Basin and Range Province. The SRP is a prominent low- relief physiographic feature that extends from eastern Oregon through southern Idaho and into northwestern Wyoming, USA. The Eastern Snake River Plain (ESRP) is a 400-km long, NE-trending volcanic province that is characterized by bimodal volcanism, which represents the track of the Yellowstone Hotspot currently located in Wyoming. The Western Snake River Plain (WSRP) is a 300-km long, NW-trending graben that extends into eastern Oregon. The WSRP is an extensional basin that formed adjacent to an earlier position of the Yellowstone Hotspot in southern Idaho. Previous geodetic investigations suggest the ESRP and, perhaps the WSRP, have GPS velocities indicative of rigid block motion of the SRP along its physiographic boundaries. GPS data compiled for this study are used to test this hypothesis. Several institutions including the National Geodetic Survey, Idaho National Laboratory, Rensselaer Polytechnic Institute, and University of Utah observed GPS stations from 1994 to 2006 within the SRP and surrounding region. Horizontal velocities show generally consistent N110°W orientations with an average rate of 1.5 ± 0.3 mm/yr (for 11 stations) along most of the ESRP and adjacent northwest Basin and Range, although some Basin and Range velocities are less and may be influenced by post viscoelastic relaxation following the 1983 Mw 6.9 normal-faulting Borah Peak, Idaho earthquake. GPS velocities with an average rate of 1.9 ± 0.3 mm/yr (for 5 stations) change orientation to N95°W at a distance of 190 km from the Yellowstone Hotspot within the southern region of the ESRP and adjacent Basin and Range. Within the WSRP, GPS velocities have an average rate of 2.0 ± 0.5 mm/yr (for 7 stations) and change orientation to N40°W. These GPS velocities are more consistent with those in eastern Oregon, a region that is rotating clockwise relative to North America. To assess possible rotations and strain rates, we invert GPS horizontal velocities, geologic fault slip rates, earthquake-derived fault slip vector azimuths, and volcanic dike extension rates. We interpret GPS velocities to describe the relative motions of coherent regions of consistent strain within the SRP and surrounding Basin and Range Province.

Slip Distribution of the 2011 Tohoku-oki Earthquake obtained by Geodetic and Tsunami Data and with a 3-D Finite Element Model

NASA Astrophysics Data System (ADS)

Romano, F.; Trasatti, E.; Lorito, S.; Ito, Y.; Piatanesi, A.; Lanucara, P.; Hirata, K.; D'Agostino, N.; Cocco, M.

2012-12-01

The rupture process of the Great 2011 Tohoku-oki earthquake has been particularly well studied by using an unprecedented collection of geophysical data. There is a general agreement among the different source models obtained by modeling seismological, geodetic and tsunami data. A slip patch of nearly 40÷50 meters has been imaged and located around and up-dip from the hypocenter by most of published models, while some differences exist in the slip pattern retrieved at shallow depths near the trench, likely due to the different resolving power of distinct data sets and to the adopted fault geometry. It is well known that the modeling of great subduction earthquakes requires the use of 3-D structural models in order to properly account for the effects of topography, bathymetry and the geometrical variations of the plate interface as well as for the effects of elastic contrasts between the subducting plate and the continental lithosphere. In this study we build a 3-D Finite Element (FE) model of the Tohoku-oki area in order to infer the slip distribution of the 2011 earthquake by performing a joint inversion of geodetic (GPS and seafloor observations) and tsunami (ocean bottom pressure sensors, DART and GPS buoys) data. The FE model is used to compute the geodetic and tsunami Green's functions. In order to understand how geometrical and elastic heterogeneities control the inferred slip distribution of the Tohoku-oki earthquake, we compare the slip patterns obtained using both homogeneous and heterogeneous structural models. The goal of this study is to better constrain the slip distribution and the maximum slip amplitudes. In particular, we aim to focus on the rupture process in the shallower part of the fault plane and near the trench, which is crucial to model the tsunami data and to assess the tsunamigenic potential of earthquakes in this region.

Integrated geodetic monitoring of subsidence due to groundwater abstraction in the Perth Basin, Western Australia

NASA Astrophysics Data System (ADS)

Parker, A. L.; Filmer, M. S.; Featherstone, W. E.; Pigois, J. P.; Lyon, T.

2016-12-01

Small-magnitude subsidence due to groundwater abstraction was first observed in Perth, Western Australia, in the 2000s. Ongoing monitoring of ground deformation is required to avoid infrastructure damage, increased risk of seawater inundation and compromised integrity of geodetic benchmarks (e.g. tide-gauges). Subsidence measurements will also be used to provide constraints on aquifer storage properties, which is of significance to groundwater-resource management and proposed managed aquifer recharge. To these ends, a geodetic monitoring system in the Perth Basin has been established incorporating repeat levelling, continuous GPS and >20 years of InSAR data, including four years of TerraSAR-X (2012 to 2016), plus the first Sentinel-1A interferograms over Western Australia. The magnitude of subsidence ( 2-5 mm/yr) is at the limit detectable with InSAR, but through integration with high-precision repeat levelling, groundwater level records and geological information, we are able to constrain and interpret the spatial and temporal characteristics of the deformation field. InSAR datasets reveal a narrow subsiding coastal strip proximal to abstraction bores that came online since the early 2000s. Subsidence is also identified at the eastern margin of the Perth Basin, where seasonal variations of 10 mm measured with repeat-levelling are attributed to expansion and contraction of shallow clays. Elsewhere in the basin, high-resolution time-series from TerraSAR-X record non-linear, often seasonal vertical land motion, which correlates with changes in water levels at artesian monitoring bores. SAR coverage of the Perth Basin is ongoing and is now complemented by corner reflectors co-located with continuous GPS to tie measurements to a consistent reference frame. The ongoing collection of these and other geodetic data ensures that we are well placed to measure and monitor vertical land motion across the Perth Basin, including any effects of proposed managed aquifer recharge.

Deriving a geocentric reference frame for satellite positioning and navigation

NASA Technical Reports Server (NTRS)

Malla, R. P.; Wu, S.-C.

1988-01-01

With the advent of Earth-orbiting geodetic satellites, nongeocentric datums or reference frames have become things of the past. Accurate geocentric three-dimensional positioning is now possible and is of great importance for various geodetic and oceanographic applications. While relative positioning accuracy of a few centimeters has become a reality using very long baseline interferometry (VLBI), the uncertainty in the offset of the adopted coordinate system origin from the geocenter is still believed to be on the order of 1 meter. Satellite laser ranging (SLR), however, is capable of determining this offset to better than 10 cm, but this is possible only after years of measurements. Global Positioning System (GPS) measurements provide a powerful tool for an accurate determination of this origin offset. Two strategies are discussed. The first strategy utilizes the precise relative positions that were predetermined by VLBI to fix the frame orientation and the absolute scaling, while the offset from the geocenter is determined from GPS measurements. Three different cases are presented under this strategy. The reference frame thus adopted will be consistent with the VLBI coordinate system. The second strategy establishes a reference frame by holding only the longitude of one of the tracking sites fixed. The absolute scaling is determined by the adopted gravitational constant (GM) of the Earth; and the latitude is inferred from the time signature of the Earth rotation in the GPS measurements. The coordinate system thus defined will be a geocentric Earth-fixed coordinate system.

Status of NGS CORS Network and Its Contribution to the GGOS Infrastructure

NASA Astrophysics Data System (ADS)

Choi, K. K.; Haw, D.; Sun, L.

2017-12-01

Recent advancement of Satellite Geodesy techniques can now contribute to the global frame realization needed to improve worldwide accuracies. These techniques rely on coordinates computed using continuously observed GPS data and corresponding satellite orbits. The GPS-based reference system continues to depend on the physical stability of a ground-based network of points as the primary foundation for these observations. NOAA's National Geodetic Survey (NGS) has been operating Continuously Operating Reference Stations (CORS) to provide direct access to the National Spatial Reference System (NSRS). By virtue of NGS' scientific reputation and leadership in national and international geospatial issues, NGS has determined to increase its participation in the maintenance of the U.S. component of the global GPS tracking network in order to realize a long-term stable national terrestrial reference frame. NGS can do so by leveraging its national leadership role coupled with NGS' scientific expertise, in designating and upgrading a subset of the current tracking network for this purpose. This subset of stations must have the highest operational standards to serve the dual functions: being the U.S. contribution to the international frame, along with providing the link to the national datum. These stations deserve special attention to ensure that the highest possible levels of quality and stability are maintained. To meet this need, NGS is working with the international scientific groups to add and designate these reference stations based on scientific merit such as: colocation with other geodetic techniques, geographic area, and monumentation stability.

Evaluation of a New Prototype Geodetic Astrolabe for Measuring Deflections of the Vertical

NASA Astrophysics Data System (ADS)

Slater, J. A.; Thompson, N.; Angell, L. E.; Belenkii, M. S.; Bruns, D. G.; Johnson, D. O.

2009-12-01

During the last three years, the National Geospatial-Intelligence Agency (NGA), with assistance from the U.S. Naval Observatory (USNO), sponsored the development of a new electronic geodetic astrolabe for measuring deflections of the vertical (DoV). NGA’s current operational astrolabes, built in 1995, have a number of undesirable features including the need for a pool of liquid mercury as a reflecting surface. The new state-of-the-art prototype instrument, completed by Trex Enterprises in early 2009, was designed to meet a 0.2 arcsec accuracy requirement. It reduces the weight, eliminates the mercury, and dramatically reduces observation times. The new astrolabe consists of a 101 mm aperture telescope with a 1.5° field of view and an inclinometer mounted inside a 92-cm high, 30-cm diameter tube, an external GPS receiver for timing, and a laptop computer that controls and monitors the instrument and performs the computations. Star images are recorded by an astronomical-grade camera with a 2,048 x 2,048 pixel CCD sensor that is externally triggered by time pulses from the GPS receiver. The prototype was designed for nighttime observation of visible stars equal to or brighter than magnitude 10.0. The inclinometer is a system of two orthogonal pendula that define the local gravitational vertical, each consisting of a brass plumb bob suspended from an aluminized polymer ribbon set between two electrodes. An internal reference collimator is rigidly tied to the inclinometer and projects an array of reference points of light onto the CCD sensor. After the astrolabe is coarsely leveled to within 20 arcsec, voice coil actuators automatically adjust and maintain the inclinometer vertical to within 0.02 arcsec. Independent images are collected at 6 second intervals using a 200 msec exposure time. The CCD coordinates are determined for each star and a collimator reference point on each image. Stars are identified by referencing a customized star catalog produced by USNO. A plate model is fitted to the topocentric coordinates of the stars, and then used to solve for the astronomical latitude and longitude of the vertical reference point on the CCD. The average of 100-150 individual image solutions (10-15 minutes) defines the astronomical position for the observation session. In order to remove an azimuthal orientation bias, the astrolabe is rotated 180°, a new observation session solution is produced for that orientation and then averaged with the first solution to get the final astronomical position of the site. By combining these coordinates with GPS-derived geodetic latitude and longitude, one obtains the DoV. Initial testing of the prototype at a known astronomic position has been completed. The tests evaluated the session-to-session and day-to-day repeatability of the solutions, the number of observations required for a solution, the accuracy with respect to the known position, and the operational robustness of the hardware and software. Based on the field tests, Trex will make improvements to the prototype hardware and software and then produce operational units for use by NGA.

Geodetic positioning of the Aerospace Electronics Research Lab (ERL) Osborne Time Transfer Receiver (TTR) using the GPS NAVSTAR Block I satellites

NASA Technical Reports Server (NTRS)

Liu, Anthony S.

1990-01-01

Aerospace has routinely processed the Osborne Time Transfer Receiver (TTR) data for the purpose of monitoring the performance of ground and GPS atomic clocks in near real-time with on-line residual displays and characterizing clock stability with Allan Variance calculations. Recently, Aerospace added the ability to estimate the TTR's location by differentially correcting the TTR's location in the WGS84 reference system. This new feature is exercised on a set of TTR clock phase data and Sub-meter accurate station location estimates of the TTR at the Aerospace Electronic Research Lab (ERL) are obtained.

Fault geometry inversion and slip distribution of the 2010 Mw 7.2 El Mayor-Cucapah earthquake from geodetic data

NASA Astrophysics Data System (ADS)

Huang, Mong-Han; Fielding, Eric J.; Dickinson, Haylee; Sun, Jianbao; Gonzalez-Ortega, J. Alejandro; Freed, Andrew M.; Bürgmann, Roland

2017-01-01

The 4 April 2010 Mw 7.2 El Mayor-Cucapah (EMC) earthquake in Baja, California, and Sonora, Mexico, had primarily right-lateral strike-slip motion and a minor normal-slip component. The surface rupture extended about 120 km in a NW-SE direction, west of the Cerro Prieto fault. Here we use geodetic measurements including near- to far-field GPS, interferometric synthetic aperture radar (InSAR), and subpixel offset measurements of radar and optical images to characterize the fault slip during the EMC event. We use dislocation inversion methods and determine an optimal nine-segment fault geometry, as well as a subfault slip distribution from the geodetic measurements. With systematic perturbation of the fault dip angles, randomly removing one geodetic data constraint, or different data combinations, we are able to explore the robustness of the inferred slip distribution along fault strike and depth. The model fitting residuals imply contributions of early postseismic deformation to the InSAR measurements as well as lateral heterogeneity in the crustal elastic structure between the Peninsular Ranges and the Salton Trough. We also find that with incorporation of near-field geodetic data and finer fault patch size, the shallow slip deficit is reduced in the EMC event by reductions in the level of smoothing. These results show that the outcomes of coseismic inversions can vary greatly depending on model parameterization and methodology.

Geodetic observations of ice flow velocities over the southern part of subglacial Lake Vostok, Antarctica, and their glaciological implications

NASA Astrophysics Data System (ADS)

Wendt, Jens; Dietrich, Reinhard; Fritsche, Mathias; Wendt, Anja; Yuskevich, Alexander; Kokhanov, Andrey; Senatorov, Anton; Lukin, Valery; Shibuya, Kazuo; Doi, Koichiro

2006-09-01

In the austral summer seasons 2001/02 and 2002/03, Global Positioning System (GPS) data were collected in the vicinity of Vostok Station to determine ice flow velocities over Lake Vostok. Ten GPS sites are located within a radius of 30km around Vostok Station on floating ice as well as on grounded ice to the east and to the west of the lake. Additionally, a local deformation network around the ice core drilling site 5G-1 was installed. The derived ice flow velocity for Vostok Station is 2.00ma-1 +/- 0.01ma-1. Along the flowline of Vostok Station an extension rate of about 10-5a-1 (equivalent to 1cm km-1 a-1) was determined. This significant velocity gradient results in a new estimate of 28700 years for the transit time of an ice particle along the Vostok flowline from the bedrock ridge in the southwest of the lake to the eastern shoreline. With these lower velocities compared to earlier studies and, hence, larger transit times the basal accretion rate is estimated to be 4mma-1 along a portion of the Vostok flowline. An assessment of the local accretion rate at Vostok Station using the observed geodetic quantities yields an accretion rate in the same order of magnitude. Furthermore, the comparison of our geodetic observations with results inferred from ice-penetrating radar data indicates that the ice flow may not have changed significantly for several thousand years.

Global Positioning System Bibliography

DTIC Science & Technology

1992-03-01

Nev., November, pp. 110-121. Chrzanowski, A. (1987). " Experiencias con GPS en mediciones de deformaciones." Presented at: Workshop on New Techniques...Material Placed in Open Waters Area 2 - Material Properties Related to Navigation and Dredging Area 3 - Dredge Plant Equipment and Systems Processes Area 4...Positioning System." Proceedings of the Second International Symposium on Problems Related to the Redefinintion of North American Geodetic Networks

Measurement and Interpretation of Crustal Deformation Rates Associated with Postglacial Rebound

NASA Technical Reports Server (NTRS)

Davis, James L.

1998-01-01

This project involves obtaining GPS measurements in Scandinavia, and using the measurements to estimate the viscosity profile of the Earth's mantle and to correct tide-gauge measurements for the rebound effect. Many aspects of this project have been reported in the literature (see Section III). In Section II, we report on the primary geodetic results from this project.

Coseismic deformation of the 2001 El Salvador and 2002 Denali fault earthquakes from GPS geodetic measurements

NASA Astrophysics Data System (ADS)

Hreinsdottir, Sigrun

2005-07-01

GPS geodetic measurements are used to study two major earthquakes, the 2001 MW 7.7 El Salvador and 2002 MW 7.9 Denali Fault earthquakes. The 2001 MW 7.7 earthquake was a normal fault event in the subducting Cocos plate offshore El Salvador. Coseismic displacements of up to 15 mm were measured at permanent GPS stations in Central America. The GPS data were used to constrain the location of and slip on the normal fault. One month later a MW 6.6 strike-slip earthquake occurred in the overriding Caribbean plate. Coulomb stress changes estimated from the M W 7.7 earthquake suggest that it triggered the MW 6.6 earthquake. Coseismic displacement from the MW 6.6 earthquake, about 40 mm at a GPS station in El Salvador, indicates that the earthquake triggered additional slip on a fault close to the GPS station. The MW 6.6 earthquake further changed the stress field in the overriding Caribbean plate, with triggered seismic activity occurring west and possibly also to the east of the rupture in the days to months following the earthquake. The MW 7.9 Denali Fault earthquake ruptured three faults in the interior of Alaska. It initiated with a thrust motion on the Susitna Glacier fault but then ruptured the Denali and Totschunda faults with predominantly right-lateral strike-slip motion unilaterally from west to east. GPS data measured in the two weeks following the earthquake suggest a complex coseismic rupture along the faults with two main regions of moment release along the Denali fault. A large amount of additional data were collected in the year following the earthquake which greatly improved the resolution on the fault, revealing more details of the slip distribution. We estimate a total moment release of 6.81 x 1020 Nm in the earthquake with a M W 7.2 thrust subevent on Susitna Glacier fault. The slip on the Denali fault is highly variable, with 4 main pulses of moment release. The largest moment pulse corresponds to a MW 7.5 subevent, about 40 km west of the Denali-Totschunda fault junction. We estimate relatively low and shallow slip on the Totschunda fault.

Research-related intercultural higher education in satellite geodesy

NASA Astrophysics Data System (ADS)

Mayer, M.; Heck, B.; Krueger, C. P.

2009-04-01

In order to improve the education of young researchers (master degree, PhD, PostDocs) a cooperation between the Department of Geomatics (DGEOM), Federal University of Paraná (UFPR), Curitiba (Brazil) and the Geodetic Institute (GIK), University Karlsruhe (TH), Karlsruhe (Germany) was established which now exists since more than five years. The joint venture is actually called "PROBRAL: Precise positioning and height determination by means of GPS: Modeling of errors and transformation into physical heights" and focuses on research and education within the field of satellite geodesy. PROBRAL is funded by the Brazilian academic exchange service CAPES and the German academic exchange service DAAD. The geodetic aim of the research project is to validate and improve the quality of 3d positions derived from observations related to satellite navigation systems like GPS. In order to fulfill this ambitious goal sustainably, research has to be carried out in close cooperation. At the same time, e.g. to guarantee continuous success, a coordinated education has to be ensured. Besides technical education aspects key competences (e.g. language, capacity for teamwork, project management skills) are trained. Within the presentation the lessons which were learned from this project are discussed in detail.

Sudden aseismic fault slip on the south flank of Kilauea volcano.

PubMed

Cervelli, Peter; Segall, Paul; Johnson, Kaj; Lisowski, Michael; Miklius, Asta

2002-02-28

One of the greatest hazards associated with oceanic volcanoes is not volcanic in nature, but lies with the potential for catastrophic flank failure. Such flank failure can result in devastating tsunamis and threaten not only the immediate vicinity, but coastal cities along the entire rim of an ocean basin. Kilauea volcano on the island of Hawaii, USA, is a potential source of such flank failures and has therefore been monitored by a network of continuously recording geodetic instruments, including global positioning system (GPS) receivers, tilt meters and strain meters. Here we report that, in early November 2000, this network recorded transient southeastward displacements, which we interpret as an episode of aseismic fault slip. The duration of the event was about 36 hours, it had an equivalent moment magnitude of 5.7 and a maximum slip velocity of about 6[?]cm per day. Inversion of the GPS data reveals a shallow-dipping thrust fault at a depth of 4.5[?]km that we interpret as the down-dip extension of the Hilina Pali--Holei Pali normal fault system. This demonstrates that continuously recording geodetic networks can detect accelerating slip, potentially leading to warnings of volcanic flank collapse.

Comparison of Kalman filter estimates of zenith atmospheric path delays using the global positioning system and very long baseline interferometry

NASA Technical Reports Server (NTRS)

Tralli, David M.; Lichten, Stephen M.; Herring, Thomas A.

1992-01-01

Kalman filter estimates of zenith nondispersive atmospheric path delays at Westford, Massachusetts, Fort Davis, Texas, and Mojave, California, were obtained from independent analyses of data collected during January and February 1988 using the GPS and VLBI. The apparent accuracy of the path delays is inferred by examining the estimates and covariances from both sets of data. The ability of the geodetic data to resolve zenith path delay fluctuations is determined by comparing further the GPS Kalman filter estimates with corresponding wet path delays derived from water vapor radiometric data available at Mojave over two 8-hour data spans within the comparison period. GPS and VLBI zenith path delay estimates agree well within one standard deviation formal uncertainties (from 10-20 mm for GPS and 3-15 mm for VLBI) in four out of the five possible comparisons, with maximum differences of 5 and 21 mm over 8- to 12-hour data spans.

Co-location satellite GPS and SLR geodetic techniques at the Felix Aguilar Astronomical Observatory of San Juan, Argentina

NASA Astrophysics Data System (ADS)

Podestá, R.; Pacheco, A. M.; Alvis Rojas, H.; Quinteros, J.; Podestá, F.; Albornoz, E.; Navarro, A.; Luna, M.

2018-01-01

This work shows the strategy followed for the co-location of the Satellite Laser Ranging (SLR) ILRS 7406 telescope and the antenna of the permanent Global Positioning System (GPS) station, located at the Félix Aguilar Astronomical Observatory (OAFA) in San Juan, Argentina. The accomplishment of the co-location consisted in the design, construction, measurement, adjustment and compensation of a geodesic net between the stations SLR and GPS, securing support points solidly built in the soil. The co-location allows the coordinates of the station to be obtained by combining the data of both SLR and GPS techniques, achieving a greater degree of accuracy than individually. The International Earth Rotation and Reference Systems Service (IERS) considers the co-located stations as the most valuable and important points for the maintenance of terrestrial reference systems and their connection with the celestial ones. The 3 mm precision required by the IERS has been successfully achieved.

Improved GPS-based time link calibration involving ROA and PTB.

PubMed

Esteban, Héctor; Palacio, Juan; Galindo, Francisco Javier; Feldmann, Thorsten; Bauch, Andreas; Piester, Dirk

2010-03-01

The calibration of time transfer links is mandatory in the context of international collaboration for the realization of International Atomic Time. In this paper, we present the results of the calibration of the GPS time transfer link between the Real Instituto y Observatorio de la Armada (ROA) and the Physikalisch-Technische Bundesanstalt (PTB) by means of a traveling geodetic-type GPS receiver and an evaluation of the achieved type A and B uncertainty. The time transfer results were achieved by using CA, P3, and also carrier phase PPP comparison techniques. We finally use these results to re-calibrate the two-way satellite time and frequency transfer (TWSTFT) link between ROA and PTB, using one month of data. We show that a TWSTFT link can be calibrated by means of GPS time comparisons with an uncertainty below 2 ns, and that potentially even sub-nanosecond uncertainty can be achieved. This is a novel and cost-effective approach compared with the more common calibration using a traveling TWSTFT station.

Precise Clock Solutions Using Carrier Phase from GPS Receivers in the International GPS Service

NASA Technical Reports Server (NTRS)

Zumberge, J. F.; Jefferson, D. C.; Stowers, D. A.; Tjoelker, R. L.; Young, L. E.

1999-01-01

As one of its activities as an Analysis Center in the International GPS Service (IGS), the Jet Propulsion Laboratory (JPL) uses data from a globally distributed network of geodetic-quality GPS receivers to estimate precise clock solutions, relative to a chosen reference, for both the GPS satellites and GPS receiver internal clocks, every day. The GPS constellation and ground network provide geometrical strength resulting in formal errors of about 100 p sec for these estimates. Some of the receivers in the global IGS network contain high quality frequency references, such as hydrogen masers. The clock solutions for such receivers are smooth at the 20-p sec level on time scales of a few minutes. There are occasional (daily to weekly) shifts at the microsec level, symptomatic of receiver resets, and 200-p sec-level discontinuities at midnight due to 1-day processing boundaries. Relative clock solutions among 22 IGS sites proposed as "fiducial" in the IGS/BIPM pilot project have been examined over a recent 4-week period. This allows a quantitative measure of receiver reset frequency as a function of site. For days and-sites without resets, the Allan deviation of the relative clock solutions is also computed for subdaily values of tau..

Automated and dynamic scheduling for geodetic VLBI - A simulation study for AuScope and global networks

NASA Astrophysics Data System (ADS)

Iles, E. J.; McCallum, L.; Lovell, J. E. J.; McCallum, J. N.

2018-02-01

As we move into the next era of geodetic VLBI, the scheduling process is one focus for improvement in terms of increased flexibility and the ability to react with changing conditions. A range of simulations were conducted to ascertain the impact of scheduling on geodetic results such as Earth Orientation Parameters (EOPs) and station coordinates. The potential capabilities of new automated scheduling modes were also simulated, using the so-called 'dynamic scheduling' technique. The primary aim was to improve efficiency for both cost and time without losing geodetic precision, particularly to maximise the uses of the Australian AuScope VLBI array. We show that short breaks in observation will not significantly degrade the results of a typical 24 h experiment, whereas simply shortening observing time degrades precision exponentially. We also confirm the new automated, dynamic scheduling mode is capable of producing the same standard of result as a traditional schedule, with close to real-time flexibility. Further, it is possible to use the dynamic scheduler to augment the 3 station Australian AuScope array and thereby attain EOPs of the current global precision with only intermittent contribution from 2 additional stations. We thus confirm automated, dynamic scheduling bears great potential for flexibility and automation in line with aims for future continuous VLBI operations.

The Performance Analysis of a Real-Time Integrated INS/GPS Vehicle Navigation System with Abnormal GPS Measurement Elimination

PubMed Central

Chiang, Kai-Wei; Duong, Thanh Trung; Liao, Jhen-Kai

2013-01-01

The integration of an Inertial Navigation System (INS) and the Global Positioning System (GPS) is common in mobile mapping and navigation applications to seamlessly determine the position, velocity, and orientation of the mobile platform. In most INS/GPS integrated architectures, the GPS is considered to be an accurate reference with which to correct for the systematic errors of the inertial sensors, which are composed of biases, scale factors and drift. However, the GPS receiver may produce abnormal pseudo-range errors mainly caused by ionospheric delay, tropospheric delay and the multipath effect. These errors degrade the overall position accuracy of an integrated system that uses conventional INS/GPS integration strategies such as loosely coupled (LC) and tightly coupled (TC) schemes. Conventional tightly coupled INS/GPS integration schemes apply the Klobuchar model and the Hopfield model to reduce pseudo-range delays caused by ionospheric delay and tropospheric delay, respectively, but do not address the multipath problem. However, the multipath effect (from reflected GPS signals) affects the position error far more significantly in a consumer-grade GPS receiver than in an expensive, geodetic-grade GPS receiver. To avoid this problem, a new integrated INS/GPS architecture is proposed. The proposed method is described and applied in a real-time integrated system with two integration strategies, namely, loosely coupled and tightly coupled schemes, respectively. To verify the effectiveness of the proposed method, field tests with various scenarios are conducted and the results are compared with a reliable reference system. PMID:23955434

The AuScope geodetic VLBI array

NASA Astrophysics Data System (ADS)

Lovell, J. E. J.; McCallum, J. N.; Reid, P. B.; McCulloch, P. M.; Baynes, B. E.; Dickey, J. M.; Shabala, S. S.; Watson, C. S.; Titov, O.; Ruddick, R.; Twilley, R.; Reynolds, C.; Tingay, S. J.; Shield, P.; Adada, R.; Ellingsen, S. P.; Morgan, J. S.; Bignall, H. E.

2013-06-01

The AuScope geodetic Very Long Baseline Interferometry array consists of three new 12-m radio telescopes and a correlation facility in Australia. The telescopes at Hobart (Tasmania), Katherine (Northern Territory) and Yarragadee (Western Australia) are co-located with other space geodetic techniques including Global Navigation Satellite Systems (GNSS) and gravity infrastructure, and in the case of Yarragadee, satellite laser ranging (SLR) and Doppler Orbitography and Radiopositioning Integrated by Satellite (DORIS) facilities. The correlation facility is based in Perth (Western Australia). This new facility will make significant contributions to improving the densification of the International Celestial Reference Frame in the Southern Hemisphere, and subsequently enhance the International Terrestrial Reference Frame through the ability to detect and mitigate systematic error. This, combined with the simultaneous densification of the GNSS network across Australia, will enable the improved measurement of intraplate deformation across the Australian tectonic plate. In this paper, we present a description of this new infrastructure and present some initial results, including telescope performance measurements and positions of the telescopes in the International Terrestrial Reference Frame. We show that this array is already capable of achieving centimetre precision over typical long-baselines and that network and reference source systematic effects must be further improved to reach the ambitious goals of VLBI2010.

Improving the Quality of Low-Cost GPS Receiver Data for Monitoring Using Spatial Correlations

NASA Astrophysics Data System (ADS)

Zhang, Li; Schwieger, Volker

2016-06-01

The investigations on low-cost single frequency GPS receivers at the Institute of Engineering Geodesy (IIGS) show that u-blox LEA-6T GPS receivers combined with Trimble Bullet III GPS antennas containing self-constructed L1-optimized choke rings can already obtain an accuracy in the range of millimeters which meets the requirements of geodetic precise monitoring applications (see [27]). However, the quality (accuracy and reliability) of low-cost GPS receiver data, particularly in shadowing environment, should still be improved, since the multipath effects are the major error for the short baselines. For this purpose, several adjoined stations with low-cost GPS receivers and antennas were set up next to the metal wall on the roof of the IIGS building and measured statically for several days. The time series of three-dimensional coordinates of the GPS receivers were analyzed. Spatial correlations between the adjoined stations, possibly caused by multipath effect, will be taken into account. The coordinates of one station can be corrected using the spatial correlations of the adjoined stations, so that the quality of the GPS measurements is improved. The developed algorithms are based on the coordinates and the results will be delivered in near-real-time (in about 30 minutes), so that they are suitable for structural health monitoring applications.

National aerospace meeting of the Institute of Navigation

NASA Astrophysics Data System (ADS)

Fell, Patrick

The program for this year's aerospace meeting of The Institute of Navigation addressed developments in the evolving Global Positioning System (GPS) of navigation satellites, inertial navigation systems, and other electronic navigation systems and their applications. Also included in the program were a limited number of papers addressing the geodetic use of the GPS system.The Global Positioning System is a constellation of 18 navigation satellites being developed by the Department of Defense to provide instantaneous worldwide navigation. The system will support a multitude of military applications. The first paper by Jacobson reviewed the engineering development of GPS navigation receivers stressing the use of common hardware and software modules. A later paper by Ould described the mechanization of a digital receiver for GPS applications designed for faster acquisition of the spread spectrum satellite transmissions than analog receivers. The paper by Brady discussed the worldwide coverage that is provided by the limited number of satellites that will constitute the GPS constellation through 1983. The capability provided by the satellites presently on orbit would support a variety of experiments at almost any location. Tables of multiple satellite availability are provided for numerous worldwide locations. For civil aviation applications, Vogel addressed the satellite geometry considerations for low cost GPS user equipment, Esposito described the Federal Aviation Administration acceptance tests of a GPS navigation receiver, and Hopkins discussed the design and capability of an integrated GPS strapdown attitude and heading reference system for avionics.

Task-Level Control for a Full Semi-Autonomous Mission: Test Platform Development and Demonstration

NASA Technical Reports Server (NTRS)

Rock, Stephen M.; LeMaster, Edward A.

2001-01-01

Pseudolites can extend the availability of GPS-type positioning systems to a wide range of applications not possible with satellite-only GPS, including indoor and deep-space applications. Conventional GPS pseudolite arrays require that the devices be pre-calibrated through a survey of their locations, typically to sub-centimeter accuracy. This can sometimes be a difficult task, especially in remote or hazardous environments. By using the GPS signals that the pseudolites broadcast, however, it is possible to have the array self-survey its own relative locations, creating a Self-Calibrating Pseudolite Array (SCPA). In order to provide the bi-directional ranging signals between devices necessary for array self-calibration, pseudolite transceivers must be used. The basic principles behind the use of transceivers to create an SCPA were first presented in paper presented to the Institute of Navigation GPS-98 Conference. This paper begins with a brief review of the transceiver architecture and the fundamental direct-ranging algorithm presented in that paper. This is followed by a description of a prototype self-differencing transceiver system that has been constructed, and a presentation of experimental code- and carrier-phase ranging data obtained using that system. A second algorithm is then described which uses these fundamental range measurements between transceiver pairs to self-calibrate a larger stationary array and to provide positioning information for a vehicle moving within that array. Simulation results validating the accuracy and effective convergence of this algorithm are also presented.

Compaction of Aquifer at Different Depths: Observations from a Vertical GPS Array in the Coastal Center of the University of Houston, Texas

NASA Astrophysics Data System (ADS)

Lee, D.; Kearns, T.; Yang, L.; Wang, G.

2014-12-01

Houston and the surrounding Harris County have experienced the detrimental effects of subsidence even prior to World War II, to the extent that the land along Galveston Bay had sunk as much as 20 feet since 1906. One dramatic example is the Brownwood subdivision, a coastal community in Baytown where continuous flooding due to subsidence forced the area to be deemed unlivable and consequently abandoned. Thus, Houston's changes in groundwater and compaction of its aquifers are of relatively high concern to those in the public (infrastructure), private (oil & gas), and international (Port of Houston Authority) sectors. One of the key questions related to the subsidence issue in Houston area is what are the contributions of sediments at different depths, and what particularly is the contribution from shallow sediments? To address these questions, University of Houston has installed a vertical GPS array in the UH Coastal Center in March 2014. The GPS array includes four permanent GPS stations with the antenna pole foundations anchored at different depths below ground surface (-10 m, -7m, -4m, 0 m). A special, double-pipe GPS antenna monument was designed for GPS stations with the array. This project was funded by an NSF grant and a UH internal grant. Five groundwater wells with the depths ranging from 2 m to 100 m below the ground surface were also installed at the UH Coastal Center site. This study will investigate continuous GPS and groundwater level measurements (March-November, 2014) at the UHCC site. It is expected that the GPS array will provide total information on subsidence as well as compaction of aquifers within different depth ranges (0 to -4m, -4 to -7 m, -7 to -10m, and below -10 m). Correlation of land subsidence and groundwater fluctuation will also be investigated.

Magma-tectonic interactions in Kīlauea's Southwest Rift Zone in 2006 through coupled geodetic/seismological analysis

NASA Astrophysics Data System (ADS)

Wauthier, C.; Roman, D. C.; Poland, M. P.

2015-12-01

For much of the first 20 years of Kīlauea's 1983-present Pu'u 'Ō'ō eruption, deformation was characterized by subsidence at the volcano's summit and along both the East Rift Zone (ERZ) and Southwest Rift Zone (SWRZ). At the end of 2003, however, Kīlauea's summit began a 4-year period of inflation due to a surge in magma supply to the volcano. In 2006, the SWRZ also experienced atypical inflation, which was last observed in 1981-82 during a series of dike intrusions. To investigate the active magma sources and their interactions with faulting in the SWRZ during 2006, we integrate contemporary geodetic data from InSAR and GPS with double-couple fault-plane solutions for volcano-tectonic earthquakes and Coulomb stress modeling. According to the rate of deformation measured in daily GPS data, two distinct periods can be defined, spanning January to 15 March 2006 (period 1) and 16 March to 30 September 2006 (period 2). Geodetic models suggest that, during period 1, deformation, due to pressurization of magma in a vertical prolate-spheroidal conduit, in the south caldera area. In addition, a major seismic swarm occurred in both the SWRZ and ERZ. Our preliminary results also suggest that, during period 2, magma was still overpressurizing the same prolate-spheroid but a subhorizontal sill also intruded further to the southwest in the seismic SWRZ (SSWRZ). The beginning of period 2 also corresponds to a switch from subsidence to inflation of the SWRZ. Faulting in the upper ERZ is primarily strike-slip, with no obvious change in FPS orientation between periods 1 and 2. In contrast, faulting in the upper SSWRZ occurs as dip-slip motion on near-vertical faults. SSWRZ FPS show a mix of orientations including NW- and NE-striking faults, which along with relative earthquake locations, suggest a series of right-stepping fault segments, particularly during period 2. Calculated Coulomb stress changes indicate that faulting in the upper SSWRZ may result from stresses produced by inflation of the geodetically modeled sources described above, in particular the prolate spheroid located in the south caldera area. In contrast, earthquakes in the ERZ are generally inhibited by the geodetically modeled sources, suggesting that another process may be responsible for faulting along the ERZ.

Rapid SAR and GPS Measurements and Models for Hazard Science and Situational Awareness

NASA Astrophysics Data System (ADS)

Owen, S. E.; Yun, S. H.; Hua, H.; Agram, P. S.; Liu, Z.; Moore, A. W.; Rosen, P. A.; Simons, M.; Webb, F.; Linick, J.; Fielding, E. J.; Lundgren, P.; Sacco, G. F.; Polet, J.; Manipon, G.

2016-12-01

The Advanced Rapid Imaging and Analysis (ARIA) project for Natural Hazards is focused on rapidly generating higher level geodetic imaging products and placing them in the hands of the solid earth science and local, national, and international natural hazard communities by providing science product generation, exploration, and delivery capabilities at an operational level. Space-based geodetic measurement techniques such as Interferometric Synthetic Aperture Radar (InSAR), Differential Global Positioning System (DGPS), SAR-based change detection, and image pixel tracking have recently become critical additions to our toolset for understanding and mapping the damage caused by earthquakes, volcanic eruptions, landslides, and floods. Analyses of these data sets are still largely handcrafted following each event and are not generated rapidly and reliably enough for response to natural disasters or for timely analysis of large data sets. The ARIA project, a joint venture co-sponsored by California Institute of Technology (Caltech) and by NASA through the Jet Propulsion Laboratory (JPL), has been capturing the knowledge applied to these responses and building it into an automated infrastructure to generate imaging products in near real-time that can improve situational awareness for disaster response. In addition, the ARIA project is developing the capabilities to provide automated imaging and analysis capabilities necessary to keep up with the imminent increase in raw data from geodetic imaging missions planned for launch by NASA, as well as international space agencies. We will present the progress we have made on automating the analysis of SAR data for hazard monitoring and response using data from Sentinel 1a/b as well as continuous GPS stations. Since the beginning of our project, our team has imaged events and generated response products for events around the world. These response products have enabled many conversations with those in the disaster response community about the potential usefulness of rapid SAR and GPS-based information. We will present progress on our data system technology that enables rapid and reliable production of imagery, as well as lessons learned from our engagement with FEMA and others in the hazard response community on the important actionable information that they need.

Steps towards Improving GNSS Systematic Errors and Biases

NASA Astrophysics Data System (ADS)

Herring, T.; Moore, M.

2017-12-01

Four general areas of analysis method improvements, three related to data analysis models and the fourth to calibration methods, have been recommended at the recent unified analysis workshop (UAW) and we discuss aspects of these areas for improvement. The gravity fields used in the GNSS orbit integrations should be updated to match modern fields to make them consistent with the fields being used by the other IAG services. The update would include the static part of the field and a time variable component. The force models associated with radiation forces are the most uncertain and modeling of these forces can be made more consistent with the exchange of attitude information. The international GNSS service (IGS) will develop an attitude format and make attitude information available so that analysis centers can validate their models. The IGS has noted the appearance of the GPS draconitic period and harmonics of this period in time series of various geodetic products (e.g., positions and Earth orientation parameters). An updated short-period (diurnal and semidiurnal) model is needed and a method to determine the best model developed. The final area, not directly related to analysis models, is the recommendation that site dependent calibration of GNSS antennas are needed since these have a direct effect on the ITRF realization and position offsets when antennas are changed. Evaluation of the effects of the use of antenna specific phase center models will be investigated for those sites where these values are available without disturbing an existing antenna installation. Potential development of an in-situ antenna calibration system is strongly encouraged. In-situ calibration would be deployed at core sites where GNSS sites are tied to other geodetic systems. With recent expansion of the number of GPS satellites transmitting unencrypted codes on the GPS L2 frequency and the availability of software GNSS receivers in-situ calibration between an existing installation and a movable directional antenna is now more likely to generate accurate results than earlier analog switching systems. With all of these improvements, there is the expectation that there will be better agreement between the space geodetic methods thus allowing more definitive assessment and modeling of the Earth's time variable shape and gravity field.

Geodetic Imaging of the Earthquake Cycle

NASA Astrophysics Data System (ADS)

Tong, Xiaopeng

In this dissertation I used Interferometric Synthetic Aperture Radar (InSAR) and Global Positioning System (GPS) to recover crustal deformation caused by earthquake cycle processes. The studied areas span three different types of tectonic boundaries: a continental thrust earthquake (M7.9 Wenchuan, China) at the eastern margin of the Tibet plateau, a mega-thrust earthquake (M8.8 Maule, Chile) at the Chile subduction zone, and the interseismic deformation of the San Andreas Fault System (SAFS). A new L-band radar onboard a Japanese satellite ALOS allows us to image high-resolution surface deformation in vegetated areas, which is not possible with older C-band radar systems. In particular, both the Wenchuan and Maule InSAR analyses involved L-band ScanSAR interferometry which had not been attempted before. I integrated a large InSAR dataset with dense GPS networks over the entire SAFS. The integration approach features combining the long-wavelength deformation from GPS with the short-wavelength deformation from InSAR through a physical model. The recovered fine-scale surface deformation leads us to better understand the underlying earthquake cycle processes. The geodetic slip inversion reveals that the fault slip of the Wenchuan earthquake is maximum near the surface and decreases with depth. The coseismic slip model of the Maule earthquake constrains the down-dip extent of the fault slip to be at 45 km depth, similar to the Moho depth. I inverted for the slip rate on 51 major faults of the SAFS using Green's functions for a 3-dimensional earthquake cycle model that includes kinematically prescribed slip events for the past earthquakes since the year 1000. A 60 km thick plate model with effective viscosity of 10 19 Pa · s is preferred based on the geodetic and geological observations. The slip rates recovered from the plate models are compared to the half-space model. The InSAR observation reveals that the creeping section of the SAFS is partially locked. This high-resolution deformation model will refine the moment accumulation rates and shear strain rates, which are not well resolved by previous models.

Preliminary results of the Geoid Slope Validation Survey 2014 in Iowa

NASA Astrophysics Data System (ADS)

Wang, Y. M.; Becker, C.; Breidenbach, S.; Geoghegan, C.; Martin, D.; Winester, D.; Hanson, T.; Mader, G. L.; Eckl, M. C.

2014-12-01

The National Geodetic Survey conducted a second Geoid Slope Validation Survey in the summer of 2014 (GSVS14). The survey took place in Iowa along U.S Route 30. The survey line is approximately 200 miles long (325 km), extending from Denison, IA to Cedar Rapids, IA. There are over 200 official survey bench marks. A leveling survey was performed, conforming to 1st order, class II specifications. A GPS survey was performed using 24 to 48 hour occupations. Absolute gravity, relative gravity, and gravity gradient measurements were also collected during the survey. In addition, deflections of the vertical were acquired at 200 eccentric survey benchmarks using the Compact Digital Astrometric Camera (CODIAC) camera. This paper presents the preliminary results of the survey, including the accuracy analysis of the leveling data, GPS ellipsoidal heights, and the deflections of the vertical which serves as an independent data set in addition to the GPS/leveling implied geoid heights.

Geodetic imaging with airborne LiDAR: the Earth's surface revealed.

PubMed

Glennie, C L; Carter, W E; Shrestha, R L; Dietrich, W E

2013-08-01

The past decade has seen an explosive increase in the number of peer reviewed papers reporting new scientific findings in geomorphology (including fans, channels, floodplains and landscape evolution), geologic mapping, tectonics and faulting, coastal processes, lava flows, hydrology (especially snow and runoff routing), glaciers and geo-archaeology. A common genesis of such findings is often newly available decimeter resolution 'bare Earth' geodetic images, derived from airborne laser swath mapping, a.k.a. airborne LiDAR, observations. In this paper we trace nearly a half century of advances in geodetic science made possible by space age technology, such as the invention of short-pulse-length high-pulse-rate lasers, solid state inertial measurement units, chip-based high speed electronics and the GPS satellite navigation system, that today make it possible to map hundreds of square kilometers of terrain in hours, even in areas covered with dense vegetation or shallow water. To illustrate the impact of the LiDAR observations we present examples of geodetic images that are not only stunning to the eye, but help researchers to develop quantitative models explaining how terrain evolved to its present form, and how it will likely change with time. Airborne LiDAR technology continues to develop quickly, promising ever more scientific discoveries in the years ahead.

Post seismic deformation associated with the 1992 Mω=7.3 Landers earthquake, southern California

USGS Publications Warehouse

Savage, J.C.; Svarc, J.L.

1997-01-01

Following the 1992 Mω=7.3 Landers earthquake, a linear array of 10 geodetic monuments at roughly 5-km spacing was established across the Emerson fault segment of the Landers rupture. The array trends perpendicular to the local strike of the fault segment and extends about 30 km on either side of it. The array was surveyed by Global Positioning System 0.034, 0.048, 0.381, 1.27, 1.88, 2.60, and 3.42 years after the Landers earthquake to measure both the spatial and temporal character of the postearthquake relaxation. The temporal behavior is described roughly by a short-term (decay time 84±23 days) exponential relaxation superimposed upon an apparently linear trend. Because the linear trend represents motions much more rapid than the observed preseismic motions, we attribute that trend to a slower (decay time greater than 5 years) postseismic relaxation, the curvature of which cannot be resolved in the short run (3.4 years) of postseismic data. About 100 mm of right-lateral displacement and 50 mm of fault-normal displacement accumulated across the geodetic array in the 3.4-year interval covered by the postseismic surveys. Those displacements are attributed to postseismic, right-lateral slip in the depth interval 10 to 30 km on the downward extension of the rupture trace. The right-lateral slip amounted to about 1 m directly beneath the geodetic array, and the fault-normal displacement is apparently primarily a consequence of the curvature of the rupture. These conclusions are based upon dislocation models fit to the observed deformation. However, no dislocation model was found with rms residuals as small as the expected observational error.

GPS Measurements of Crustal Deformation in San Diego, CA: Results from fixed-height monument network and implications for the Inner Continental Borderlands

NASA Astrophysics Data System (ADS)

Singleton, D. M.; Agnew, D. C.; Maloney, J. M.; Rockwell, T. K.

2017-12-01

The Newport-Inglewood-Rose Canyon fault zone is the easternmost fault in a system of strike-slip faults that together make up the Inner Continental Borderlands (ICB), a region offshore of Southern California that is thought to accommodate 10-15% of the total plate boundary slip. However, slip on individual faults is difficult to measure because of the offshore location and limited availability of geologic indicators. With a 30-km onshore segment, the southern Rose Canyon fault zone (RCF) provides an opportunity to employ geodetic techniques to quantify the slip rate for a fault within the ICB. Space geodetic techniques have significantly enhanced our ability to quantify tectonic motion. With a best-estimated geologic slip rate of 1.5 ± 0.5 mm/yr, the RCF, as with other low slip-rate faults, is a challenge to traditional survey GPS techniques. Here we present the results from surveys of a GPS network first constructed in 1998 to determine motion across the RCF. This network has four sites, each site consisting of three to five closely spaced benchmarks that employ novel fixed-height centering with submillimeter repeatability so as to reduce noise associated with monument stability. Data collected from 1998 to 2017 shows millimeter-level monument stability and repeatability of the network. We present the results of velocity inversion for slip using data spanning 19 years across the Rose Canyon fault zone and discuss the implications for broader motion across the Inner Continental Borderlands.

USGS Menlo Park GPS Data Processing Techniques and Derived North America Velocity Field (Invited)

NASA Astrophysics Data System (ADS)

Svarc, J. L.; Murray-Moraleda, J. R.; Langbein, J. O.

2010-12-01

The U.S. Geological Survey in Menlo Park routinely conducts repeated GPS surveys of geodetic markers throughout the western United States using dual-frequency geodetic GPS receivers. We combine campaign, continuous, and semi-permanent data to present a North America fixed velocity field for regions in the western United States. Mobile campaign-based surveys require less up-front investment than permanently monumented and telemetered GPS systems, and hence have achieved a broad and dense spatial coverage. The greater flexibility and mobility comes at the cost of greater uncertainties in individual daily position solutions. We also routinely process continuous GPS data collected at PBO stations operated by UNAVCO along with data from other continuous GPS networks such as BARD, PANGA, and CORS operated by other agencies. We have broken the Western US into several subnetworks containing approximately 150-250 stations each. The data are processed using JPL’s GIPSY-OASIS II release 5.0 software using a modified precise positioning strategy (Zumberge and others, 1997). We use the “ambizap” code provided by Geoff Blewitt (Blewitt, 2008) to fix phase ambiguities in continuous networks. To mitigate the effect of common mode noise we use the positions of stations in the network with very long, clean time series (i.e. those with no large outliers or offsets) to transform all position estimates into “regionally filtered” results following the approach of Hammond and Thatcher (2007). Velocity uncertainties from continuously operated GPS stations tend to be about 3 times smaller than those from campaign data. Langbein (2004) presents a maximum likelihood method for fitting a time series employing a variety of temporal noise models. We assume that GPS observations are contaminated by a combination of white, flicker, and random walk noise. For continuous and semi-permanent time series longer than 2 years we estimate these values, otherwise we fix the amplitudes of these processes to 0.85 mm, 1.7 mm/yr1/4, and 0.4 mm/yr1/2 respectively for the north components, 0.84 mm, 1.4 mm/yr1/4, and 0.6 mm/yr1/2 respectively for the east components and 3.2 mm, 6.4 mm/yr1/4, and 0.0 mm/yr1/2 respectively for the vertical. We have also deployed “semi-permanent” stations in selected regions of California. Semi-permanent stations have the advantage of increasing the density of coverage without the high cost of monumentation and telemetry associated with continuous GPS stations. Also, because of the increased temporal coverage of these stations, accurate estimates of station velocities can be achieved in a far shorter time period than from campaign mode surveys.

Improvement in the observation system for the GPS/A seafloor positioning

NASA Astrophysics Data System (ADS)

Fujimoto, H.; Kido, M.; Osada, Y.

2010-12-01

GPS/Acoustic seafloor positioning has become an indispensable geodetic observation for the monitoring of crustal activities near plate boundaries. There remain, however, substantial differences from GPS observation on land. Our group in Tohoku University has been working to cope with the problems under the program of the DONET, JAMSTEC.One of critical problems regarding the present GPS/A observation lies in the campaign style observation spending one or two days to measure the position of an array of acoustic transponders (PXPs) once or twice a year. It is similar to the triangulation observation on land before the age of the GPS. Chadwell et al. (2009, AGU Fall Meeting) made a step forward for this problem by carrying out a continuous GPS/A observation with a moored buoy. We are also developing a system using a moored small buoy. Precision of seafloor positioning by GPS/A is another critical problems. Considering that plate motions are several centimeters per year in most cases, precision of a few centimeters by GPS/A is a big difference from a few millimeters by GPS on land. We estimate that lateral variations in the sound velocity in the ocean can be a key to improve the precision in the positioning and to reduce the required time for the measurement, we have tried to estimate the lateral variations in the acoustic velocity by using 4-5 PXPs (Kido et al., 2006; Kido et al., this meeting). Long-term attitude stability of the position of a PXP deployed on thick sediment has been a basic problem in the GPS/A observation. While a pillar of a GPS antenna for an observation point is set up firmly on the ground, a PXP is deployed on the seafloor after a free fall from the sea surface. It is a serious problem to detect coseismic crustal movements on the seafloor. M7-class earthquakes occurred in 2004 off Kii Peninsula, Central Japan, gave us an opportunity to study the problem. By using an ROV (remotely operated vehicle), we visually observed ten PXPs in 2006, seven of which had been used to detect coseismic seafloor crustal movements of 20 cm or more as was reported by Kido et al. (2006) and by Tadokoro et al. (2006). The diving survey confirmed that all of the seven PXPs stood stably on the flat sediment, no effects of the earthquakes being recognized. Even if slight tilts of the PXPs were caused by the earthquakes, the effect on the seafloor positioning by GPS/A was estimated to be 1 cm or less (Fujimoto et al., in press). A PXP has been deployed for a permanent (actually several to 10 years) use. Therefore, it is not equipped with a recovery system as is used for an ocean bottom seismometers or pressure recorders. From our experience we have often wished to retrieve a PXP to revise its performance, to slightly change its position, or to reuse it after the battery is exhausted. We tried to use a long-life acoustic recovery system for three PXPs. We successfully recovered all of them 4.5 years after their deployment.

Gravity data from the San Pedro River Basin, Cochise County, Arizona

USGS Publications Warehouse

Kennedy, Jeffrey R.; Winester, Daniel

2011-01-01

The U.S. Geological Survey, Arizona Water Science Center in cooperation with the National Oceanic and Atmospheric Administration, National Geodetic Survey has collected relative and absolute gravity data at 321 stations in the San Pedro River Basin of southeastern Arizona since 2000. Data are of three types: observed gravity values and associated free-air, simple Bouguer, and complete Bouguer anomaly values, useful for subsurface-density modeling; high-precision relative-gravity surveys repeated over time, useful for aquifer-storage-change monitoring; and absolute-gravity values, useful as base stations for relative-gravity surveys and for monitoring gravity change over time. The data are compiled, without interpretation, in three spreadsheet files. Gravity values, GPS locations, and driving directions for absolute-gravity base stations are presented as National Geodetic Survey site descriptions.

Volcano geodesy: Challenges and opportunities for the 21st century

USGS Publications Warehouse

Dzurisin, D.

2000-01-01

Intrusions of magma beneath volcanoes deform the surrounding rock and, if the intrusion is large enough, the overlying ground surface. Numerical models generally agree that, for most eruptions, subsurface volume changes are sufficient to produce measurable deformation at the surface. Studying this deformation can help to determine the location, volume, and shape of a subsurface magma body and thus to anticipate the onset and course of an eruption. This approach has been successfully applied at many restless volcanoes, especially basaltic shields and silicic calderas, using various geodetic techniques and sensors. However, its success at many intermediate-composition strato-volcanoes has been limited by generally long repose intervals, steep terrain, and structural influences that complicate the history and shape of surface deformation. These factors have made it difficult to adequately characterize deformation in space and time at many of the world's dangerous volcanoes. Recent technological advances promise to make this task easier by enabling the acquisition of geodetic data of high spatial and temporal resolution from Earth-orbiting satellites. Synthetic aperture radar interferometry (InSAR) can image ground deformation over large areas at metre-scale resolution over time-scales of a month to a few years. Global Positioning System (GPS) stations can provide continuous information on three-dimensional ground displacements at a network of key sites -information that is especially important during volcanic crises. By using InSAR to determine the shape of the displacement field and GPS to monitor temporal changes at key sites, scientists have a much better chance to capture geodetic signals that have so far been elusive at many volcanoes. This approach has the potential to provide longer-term warnings of impending volcanic activity than is possible with other monitoring techniques.

Gravity measurements in southeastern Alaska reveal negative gravity rate of change caused by glacial isostatic adjustment

NASA Astrophysics Data System (ADS)

Sun, W.; Miura, S.; Sato, T.; Sugano, T.; Freymueller, J.; Kaufman, M.; Larsen, C. F.; Cross, R.; Inazu, D.

2010-12-01

For the past 300 years, southeastern Alaska has undergone rapid ice-melting and land uplift attributable to global warming. Corresponding crustal deformation (3 cm/yr) caused by the Little Ice Age retreat is detectable with modern geodetic techniques such as GPS and tidal gauge measurements. Geodetic deformation provides useful information for assessing ice-melting rates, global warming effects, and subcrustal viscosity. Nevertheless, integrated geodetic observations, including gravity measurements, are important. To detect crustal deformation caused by glacial isostatic adjustment and to elucidate the viscosity structure in southeastern Alaska, Japanese and U.S. researchers began a joint 3-year project in 2006 using GPS, Earth tide, and absolute gravity measurements. A new absolute gravity network was established, comprising five sites around Glacier Bay, near Juneau, Alaska. This paper reports the network's gravity measurements during 2006-2008. The bad ocean model in this area hindered ocean loading correction: Large tidal residuals remain in the observations. Accurate tidal correction necessitated on-site tidal observation. Results show high observation precision for all five stations: <1 μGal. The gravity rate of change was found to be -3.5 to -5.6 μGal/yr in the gravity network. Furthermore, gravity results obtained during the 3 years indicate a similar gravity change rate. These gravity data are anticipated for application in geophysical studies of southeastern Alaska. Using gravity and vertical displacement data, we constructed a quantity to remove viscoelastic effects. The observations are thus useful to constrain present-day ice thickness changes. A gravity bias of about -13.2 ± 0.1 mGal exists between the Potsdam and current FG5 gravity data.

Land water storage from space and the geodetic infrastructure

NASA Astrophysics Data System (ADS)

Cazenave, A.; Larson, K.; Wahr, J.

2009-04-01

In recent years, remote sensing techniques have been increasingly used to monitor components of the water balance of large river basins. By complementing scarce in situ observations and hydrological modelling, space observations have the potential to significantly improve our understanding of hydrological processes at work in river basins and their relationship with climate variability and socio-economic life. Among the remote sensing tools used in land hydrology, several originate from space geodesy and are integral parts of the Global Geodetic Observing System. For example, satellite altimetry is used for systematic monitoring of water levels of large rivers, lakes and floodplains. InSAR allows the detection of surface water change. GRACE-based space gravity offers for the first time the possibility of directly measuring the spatio-temporal variations of the vertically integrated water storage in large river basins. GRACE is also extremely useful for measuring changes in mass of the snow pack in boreal regions. Vertical motions of the ground induced by changes in water storage in aquifers can be measured by both GPS and InSAR. These techniques can also be used to investigate water loading effects. Recently GPS has been used to measure changes in surface soil moisture, which would be important for agriculture, weather prediction, and for calibrationg satellite missions such as SMOS and SMAP. These few examples show that space and ground geodetic infrastructures are increasingly important for hydrological sciences and applications. Future missions like SWOT (Surface Waters Ocean Topography; a wide swath interferometric altimetry mission) and GRACE 2 (space gravimetry mission based on new technology) will provide a new generation of hydrological products with improved precision and resolution.

Accurate determination of the geoid undulation N

NASA Astrophysics Data System (ADS)

Lambrou, E.; Pantazis, G.; Balodimos, D. D.

2003-04-01

This work is related to the activities of the CERGOP Study Group Geodynamics of the Balkan Peninsula, presents a method for the determination of the variation ΔN and, indirectly, of the geoid undulation N with an accuracy of a few millimeters. It is based on the determination of the components xi, eta of the deflection of the vertical using modern geodetic instruments (digital total station and GPS receiver). An analysis of the method is given. Accuracy of the order of 0.01arcsec in the estimated values of the astronomical coordinates Φ and Δ is achieved. The result of applying the proposed method in an area around Athens is presented. In this test application, a system is used which takes advantage of the capabilities of modern geodetic instruments. The GPS receiver permits the determination of the geodetic coordinates at a chosen reference system and, in addition, provides accurate timing information. The astronomical observations are performed through a digital total station with electronic registering of angles and time. The required accuracy of the values of the coordinates is achieved in about four hours of fieldwork. In addition, the instrumentation is lightweight, easily transportable and can be setup in the field very quickly. Combined with a stream-lined data reduction procedure and the use of up-to-date astrometric data, the values of the components xi, eta of the deflection of the vertical and, eventually, the changes ΔN of the geoid undulation are determined easily and accurately. In conclusion, this work demonstrates that it is quite feasible to create an accurate map of the geoid undulation, especially in areas that present large geoid variations and other methods are not capable to give accurate and reliable results.

GPS Imaging of Time-Variable Earthquake Hazard: The Hilton Creek Fault, Long Valley California

NASA Astrophysics Data System (ADS)

Hammond, W. C.; Blewitt, G.

2016-12-01

The Hilton Creek Fault, in Long Valley, California is a down-to-the-east normal fault that bounds the eastern edge of the Sierra Nevada/Great Valley microplate, and lies half inside and half outside the magmatically active caldera. Despite the dense coverage with GPS networks, the rapid and time-variable surface deformation attributable to sporadic magmatic inflation beneath the resurgent dome makes it difficult to use traditional geodetic methods to estimate the slip rate of the fault. While geologic studies identify cumulative offset, constrain timing of past earthquakes, and constrain a Quaternary slip rate to within 1-5 mm/yr, it is not currently possible to use geologic data to evaluate how the potential for slip correlates with transient caldera inflation. To estimate time-variable seismic hazard of the fault we estimate its instantaneous slip rate from GPS data using a new set of algorithms for robust estimation of velocity and strain rate fields and fault slip rates. From the GPS time series, we use the robust MIDAS algorithm to obtain time series of velocity that are highly insensitive to the effects of seasonality, outliers and steps in the data. We then use robust imaging of the velocity field to estimate a gridded time variable velocity field. Then we estimate fault slip rate at each time using a new technique that forms ad-hoc block representations that honor fault geometries, network complexity, connectivity, but does not require labor-intensive drawing of block boundaries. The results are compared to other slip rate estimates that have implications for hazard over different time scales. Time invariant long term seismic hazard is proportional to the long term slip rate accessible from geologic data. Contemporary time-invariant hazard, however, may differ from the long term rate, and is estimated from the geodetic velocity field that has been corrected for the effects of magmatic inflation in the caldera using a published model of a dipping ellipsoidal magma chamber. Contemporary time-variable hazard can be estimated from the time variable slip rate estimated from the evolving GPS velocity field.

Laser, GPS and absolute gravimetry vertical positioning time series comparison at the OCA observatory, France

NASA Astrophysics Data System (ADS)

Nicolas, J.; Nocquet, J.; van Camp, M.; Coulot, D.

2003-12-01

Time-dependent displacements of stations usually have magnitude close to the accuracy of each individual technique, and it still remains difficult to separate the true geophysical motion from possible artifacts inherent to each space geodetic technique. The Observatoire de la C“te d'Azur (OCA), located at Grasse, France benefits from the collocation of several geodetic instruments and techniques (3 laser ranging stations, and a permanent GPS) what allows us to do a direct comparison of the time series. Moreover, absolute gravimetry measurement campaigns have also been regularly performed since 1997, first by the "Ecole et Observatoire des Sciences de la Terre (EOST) of Strasbourg, France, and more recently by the Royal Observatory of Belgium. This study presents a comparison between the positioning time series of the vertical component derived from the SLR and GPS analysis with the gravimetric results from 1997 to 2003. The laser station coordinates are based on a LAGEOS -1 and -2 combined solution using reference 10-day arc orbits, the ITRF2000 reference frame, and the IERS96 conventions. Different GPS weekly global solutions provided from several IGS are combined and compared to the SLR results. The absolute gravimetry measurements are converted into vertical displacements with a classical gradient. The laser time series indicate a strong annual signal at the level of about 3-4 cm peak to peak amplitude on the vertical component. Absolute gravimetry data agrees with the SLR results. GPS positioning solutions also indicate a significant annual term, but with a magnitude of only 50% of the one shown by the SLR solution and by the gravimetry measurements. Similar annual terms are also observed on other SLR sites we processed, but usually with! lower and various amplitudes. These annual signals are also compared to vertical positioning variations corresponding to an atmospheric loading model. We present the level of agreement between the different techniques and we discuss possible explanations for the discrepancy noted between the signals. At last, we expose explanations for the large annual term at Grasse: These annual variations could be partly due to an hydrological loading effect on the karstic massif on which the observatory is located.

GPS Imaging suggests links between climate, magmatism, seismicity, and tectonics in the Sierra Nevada-Long Valley Caldera-Walker Lane system, western United States

NASA Astrophysics Data System (ADS)

Hammond, W. C.; Blewitt, G.; Kreemer, C.; Smith, K.

2017-12-01

The Walker Lane is a region of complex active crustal transtension in the western Great Basin of the western United States, accommodating about 20% of the 50 mm/yr relative motion between the Pacific and North American plates. The Long Valley caldera lies in the central Walker Lane in eastern California, adjacent to the eastern boundary of the Sierra Nevada/Great Valley microplate, and experiences intermittent inflation, uplift, and volcanic unrest from the magma chamber that resides at middle crustal depths. Normal and transform faults accommodating regional tectonic transtension pass by and through the caldera, complicating the interpretation of the GPS-measured strain rate field, estimates of fault slip rates, and seismic hazard. Several dozen continuously recording GPS stations measure strain and uplift in the area with mm precision. They observe that the most recent episode of uplift at Long Valley began in mid-2011, continuing until late 2016, raising the surface by 100 mm in 6 years. The timing of the initiation of uplift coincides with the beginning of severe drought in California. Furthermore, the timing of a recent pause in uplift coincides with the very wet 2016-2017 winter, which saw approximately double normal snow pack. In prior studies, we showed that the timing of changes in geodetically measured uplift rate of the Sierra Nevada coincides with the timing of drought conditions in California, suggesting a link between hydrological loading and Sierra Nevada elevation. Here we take the analysis three steps further to show that changes in Sierra Nevada uplift rate coincide in time with 1) enhanced inflation at the Long Valley caldera, 2) shifts in the patterns and rates of horizontal tensor strain rate, and 3) seismicity patterns in the central Walker Lane. We use GPS solutions from the Nevada Geodetic Laboratory and the new GPS Imaging technique to produce robust animations of the time variable strain and uplift fields. The goals of this work are to document links between climate, Sierra Nevada uplift rates, response of the magmatic system, and seismicity in the Central Walker Lane, and to explore the physical mechanisms that may be behind these correlations.

Evaluating Pseudorange Multipath at CGPS Stations Spanning Mexico

NASA Astrophysics Data System (ADS)

Vazquez, G.; Bennett, R. A.; Spinler, J. C.

2013-12-01

A research study was conducted in order to quantify and analyze the amount of pseudorange multipath at continuous Global Positioning System (CGPS) stations spanning Mexico. These CGPS stations are administered by a variety of organizations, including government agencies and public universities, and thus serve a wide range of positioning needs. Despite the diversity of the networks and their intended audiences, a core function of all of the networks is to provide a stable framework for high-precision positioning in support of diverse commercial and scientific applications. CGPS data from a large number of publicly available networks located in Mexico were studied. These include the RGNA (National Active Geodetic Network) administered by INEGI (National Institute of Statistics and Geography), the PBO network (Plate Boundary Observatory) funded by the National Science Foundation (NSF) and operated by UNAVCO (University NAVstar Consortium), the Southern California Integrated GPS Network (SCIGN), which is a collaboration effort of the United States Geological Survey (USGS), Scripps Institution of Oceanography and the Jet Propulsion Laboratory (JPL), the UNAM network, operated by the National Seismological System (SSN) and the Institute of Geophysics of the National Autonomous University of Mexico (UNAM), the Suominet Geodetic Network (SNG) and the CORS (Continuously Operating Reference Station) network, operated by the Federal Aviation Administration (FAA). A total of 54 CGPS stations were evaluated, where dual-frequency geodetic-grade receivers collected GPS data continuously during the period from 1994 to 2013. It is usually assumed that despite carefully selected locations, all CGPS stations are to some extent, affected by the presence of signal multipath. In addition, the geographic distribution of stations provides a nation-wide access to the International Terrestrial Reference Frame (ITRF). For real-time kinematic (RTK) and rapid static applications that depend on the pseudo-range observable, the accuracy with which a roaming user may locate their assets with respect to the ITRF may be limited by site-specific multipath. The issue is particularly critical for users depending on pseudorange measurements for 'real-time' (or 'near-real-time') kinematic GPS positioning, where ambiguity resolution is a critical step. Therefore, to identify the most and the least affected GPS stations we analyzed the averaged daily root mean square pseudorange multipath variations (MP1-RMS and MP2-RMS) for all feasible satellites tracked by the CGPS networks. We investigated the sources of multipath, including changes associated with hardware replacement (i.e., receiver and antenna type) and receiver firmware upgrades.

3D surface flow kinematics derived from airborne UAVSAR interferometric synthetic aperture radar to constrain the physical mechanisms controlling landslide motion

NASA Astrophysics Data System (ADS)

Delbridge, B. G.; Burgmann, R.; Fielding, E. J.; Hensley, S.; Schulz, W. H.

2013-12-01

This project focuses on improving our understanding of the physical mechanisms controlling landslide motion by studying the landslide-wide kinematics of the Slumgullion landslide in southwestern Colorado using interferometric synthetic aperture radar (InSAR) and GPS. The NASA/JPL UAVSAR airborne repeat-pass SAR interferometry system imaged the Slumgullion landslide from 4 look directions on eight flights in 2011 and 2012. Combining the four look directions allows us to extract the full 3-D velocity field of the surface. Observing the full 3-dimensional flow field allows us to extract the full strain tensor (assuming free surface boundary conditions and incompressible flow) since we have both the spatial resolution to take spatial derivates and full deformation information. COSMO-SkyMed(CSK) high-resolution Spotlight data was also acquired during time intervals overlapping with the UAVSAR one-week pairs, with intervals as short as one day. These observations allow for the quantitative testing of the deformation magnitude and estimated formal errors in the UAVSAR derived deformation field. We also test the agreement of the deformation at 20 GPS monitoring sites concurrently acquired by the USGS. We also utilize the temporal resolution of real-time GPS acquired by the UC Berkeley Active Tectonics Group during a temporary deployment from July 22nd - August 2nd. By combining this data with the kinematic data we hope to elucidate the response of the landslide to environmental changes such as rainfall, snowmelt, and atmospheric pressure, and consequently the mechanisms controlling the dynamics of the landslide system. To constrain the longer temporal dynamics, interferograms made from pairs of CSK images acquired in 2010, 2011, 2012 and 2013 reveal the slide deformation on a longer timescale by allowing us to measure meters of motion and see the average rates over year long intervals using pixel offset tracking of the high-resolution SAR amplitude images. The results of this study will also allow us to test the agreement and commensurability of UAVSAR- derived deformation with real-time GPS observations and traditional satellite-based SAR interferometry from the COSMOSkyMed system. We will not only help mitigate the hazards associated with large landslides, but also provide information on the limitations of current geodetic imaging techniques. This unique opportunity to compare several concurrent geodetic observations of the same deformation will provide constraints and recommendations for the design and implementation of future geodetic systems for the monitoring of Earth surface processes.

Seismogeodesy for rapid earthquake and tsunami characterization

NASA Astrophysics Data System (ADS)

Bock, Y.

2016-12-01

Rapid estimation of earthquake magnitude and fault mechanism is critical for earthquake and tsunami warning systems. Traditionally, the monitoring of earthquakes and tsunamis has been based on seismic networks for estimating earthquake magnitude and slip, and tide gauges and deep-ocean buoys for direct measurement of tsunami waves. These methods are well developed for ocean basin-wide warnings but are not timely enough to protect vulnerable populations and infrastructure from the effects of local tsunamis, where waves may arrive within 15-30 minutes of earthquake onset time. Direct measurements of displacements by GPS networks at subduction zones allow for rapid magnitude and slip estimation in the near-source region, that are not affected by instrumental limitations and magnitude saturation experienced by local seismic networks. However, GPS displacements by themselves are too noisy for strict earthquake early warning (P-wave detection). Optimally combining high-rate GPS and seismic data (in particular, accelerometers that do not clip), referred to as seismogeodesy, provides a broadband instrument that does not clip in the near field, is impervious to magnitude saturation, and provides accurate real-time static and dynamic displacements and velocities in real time. Here we describe a NASA-funded effort to integrate GPS and seismogeodetic observations as part of NOAA's Tsunami Warning Centers in Alaska and Hawaii. It consists of a series of plug-in modules that allow for a hierarchy of rapid seismogeodetic products, including automatic P-wave picking, hypocenter estimation, S-wave prediction, magnitude scaling relationships based on P-wave amplitude (Pd) and peak ground displacement (PGD), finite-source CMT solutions and fault slip models as input for tsunami warnings and models. For the NOAA/NASA project, the modules are being integrated into an existing USGS Earthworm environment, currently limited to traditional seismic data. We are focused on a network of dozens of seismogeodetic stations available through the Pacific Northwest Seismic Network (University of Washington), the Plate Boundary Observatory (UNAVCO) and the Pacific Northwest Geodetic Array (Central Washington University) as the basis for local tsunami warnings for a large subduction zone earthquake in Cascadia.

Accuracy of Single Frequency GPS Observations Processing In Near Real-time With Use of Code Predicted Products

NASA Astrophysics Data System (ADS)

Wielgosz, P. A.

In this year, the system of active geodetic GPS permanent stations is going to be estab- lished in Poland. This system should provide GPS observations for a wide spectrum of users, especially it will be a great opportunity for surveyors. Many of surveyors still use cheaper, single frequency receivers. This paper focuses on processing of single frequency GPS observations only. During processing of such observations the iono- sphere plays an important role, so we concentrated on the influence of the ionosphere on the positional coordinates. Twenty consecutive days of GPS data from 2001 year were processed to analyze the accuracy of a derived three-dimensional relative vec- tor position between GPS stations. Observations from two Polish EPN/IGS stations: BOGO and JOZE were used. In addition to, a new test station - IGIK was created. In this paper, the results of single frequency GPS observations processing in near real- time are presented. Baselines of 15, 27 and 42 kilometers and sessions of 1, 2, 3, 4, and 6 hours long were processed. While processing we used CODE (Centre for Orbit De- termination in Europe, Bern, Switzerland) predicted products: orbits and ionosphere info. These products are available in real-time and enable near real-time processing. Software Bernese v. 4.2 for Linux and BPE (Bernese Processing Engine) mode were used. These results are shown with a reference to dual frequency weekly solution (the best solution). Obtained GPS positional time and GPS baseline length dependency accuracy is presented for single frequency GPS observations.

Modeling Geodetic Processes with Levy α-Stable Distribution and FARIMA

NASA Astrophysics Data System (ADS)

Montillet, Jean-Philippe; Yu, Kegen

2015-04-01

Over the last years the scientific community has been using the auto regressive moving average (ARMA) model in the modeling of the noise in global positioning system (GPS) time series (daily solution). This work starts with the investigation of the limit of the ARMA model which is widely used in signal processing when the measurement noise is white. Since a typical GPS time series consists of geophysical signals (e.g., seasonal signal) and stochastic processes (e.g., coloured and white noise), the ARMA model may be inappropriate. Therefore, the application of the fractional auto-regressive integrated moving average (FARIMA) model is investigated. The simulation results using simulated time series as well as real GPS time series from a few selected stations around Australia show that the FARIMA model fits the time series better than other models when the coloured noise is larger than the white noise. The second fold of this work focuses on fitting the GPS time series with the family of Levy α-stable distributions. Using this distribution, a hypothesis test is developed to eliminate effectively coarse outliers from GPS time series, achieving better performance than using the rule of thumb of n standard deviations (with n chosen empirically).

Neotectonics of Puerto Rico and the Virgin Islands, northeastern Caribbean, from GPS geodesy

NASA Astrophysics Data System (ADS)

Jansma, Pamela E.; Mattioli, Glen S.; Lopez, Alberto; Demets, Charles; Dixon, Timothy H.; Mann, Paul; Calais, Eric

2000-12-01

The boundary between the North American and Caribbean plates is characterized primarily by left-lateral motion along predominantly east-west striking faults. Seismicity and marine geophysical survey data are consistent with at least two, and possibly three, microplates in the diffuse boundary zone in the northeastern Caribbean: (1) the Gonave, (2) the Hispaniola, and (3) the Puerto Rico-northern Virgin Islands (PRVI). We discuss results from GPS geodetic measurements acquired since 1994 to test the microplate hypothesis, define PRVI translation and rotation within the boundary zone, and constrain PRVI neotectonics. GPS-derived velocities are analyzed with respect to both North American and Caribbean plate reference frames. Integrated displacements across PRVI are limited to a few millimeters per year, consistent with a rigid PRVI and permitting calculation of an average velocity for PRVI. The motions of PRVI relative to North America and the Caribbean are 16.9±1.1 mm/yr toward N68°E±3° (1σ) and 2.4±1.4 mm/yr toward S79°W±26° (1σ), respectively. In contrast with some recent models, ongoing rotation of PRVI about a nearby (< 25° distant) vertical axis is not supported by the geodetic data. In addition, we argue against eastward tectonic escape of PRVI and favor a simple, progressive increase in velocity across the plate boundary zone, requiring that the summed magnitude of strike-slip fault slip rates will equal the total plate motion rate between the Caribbean and North America. GPS data are consistent with components of left-lateral strike-slip faulting along the Muertos trough south of Puerto Rico and shortening across the Puerto Rico trench. Comparison of GPS velocities for PRVI with respect to North America with total North America-Caribbean relative motion suggests up to 85% of North American-Caribbean plate motion is accommodated by the Puerto Rico trench and offshore faults north of Puerto Rico. Differences in GPS-derived velocities from Hispaniola and PRVI yield east-west extension across the N-S trending Mona rift of a few millimeters per year when estimated elastic strain accumulation effects along the north Hispaniola deformed belt and the Septentrional fault zone are considered. The opening rate implies an age of the Mona rift of 2-3 million years, agreeing with marine geophysical data that support a young age for the structure.

CGPS Implementation and Lidar/Laser Altimeter Experiences at l'Estartit, Ibiza and Barcelona Harbours for Sea Level Monitoring

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J.; Schutz, B.; Urban, T.; Ortiz Castellon, M.; Martinez-Garcia, M.; Ruiz, A.; Perez, B.; Rodriguez-Velasco, G.

2008-12-01

In the framework of a Spanish Space Project, the instrumentation of sea level measurements has been improved by providing the Barcelona site with a radar tide gauge and with a continuous GPS station nearby. The radar tide gauge is a Datamar 3000C device and a Thales Navigation Internet-Enabled GPS Continuous Geodetic Reference Station (iCGRS) with a choke ring antenna. It is intended that the overall system will constitute a CGPS Station of the ESEAS (European Sea Level) and TIGA (GPS Tide Gauge Benchmark Monitoring) networks. Puertos del Estado (Spanish Harbours) installed the tide gauge station at Ibiza harbour in January 2003. The station belongs to the REDMAR network, composed at this moment by 21 stations distributed along the whole Spanish waters, including also the Canary islands. The tide gauge also belongs to the ESEAS (European Sea Level) network. At the Barcelona harbour they have installed a radar tide gauge near a GPS station belonging to Puerto de Barcelona. L'Estartit floating tide gauge was set up in 1990. Data are taken in graphics registers from each two hours the mean value is recorded in an electronic support. L'Estartit tide gauge series provides good quality information about the changes in the sea heights at centimeter level, that is the magnitude of the common tides in the Mediterranean. Two airborne calibration campaigns carrying an Optech Lidar ALTM-3025 (ICC) were made on June 16, 2007 with a Partenavia P-68 and October 12, 2007, with a Cessna Caravan 208B flying along two ICESat target tracks including crossover near l'Estartit. The validation of this new technology LIDAR may be useful to fill coastal areas where satellite radar altimeters are not measuring due to the large footprint and the resulting gaps of about 15-30 km within the coastline. Measurements with a GPS Buoy at l'Estartit harbour were made during the June experience and a GPS reference station was installed in Aiguablava. On October 12, 2007, another LIDAR campaign was made at night at the same time of the ICESat overflying. A description of the actual geodetic CGPS infrastructures at Ibiza, l'Estartit and Barcelona is presented as their applications to sea level monitoring and altimeter calibration.

Forearc Sliver Translation, a Lack of Arc-Normal Strain Accumulation, and Interplate Thrust Earthquakes: GPS Geodesy in Western Nicaragua

NASA Astrophysics Data System (ADS)

Turner, H. L.; Mattioli, G. S.; Jansma, P. E.; Styron, R. H.

2007-05-01

We have been investigating the kinematics of the Nicaraguan forearc using campaign GPS measurements of our geodetic network made over the last seven years (Turner et al., 2007). We currently have interseismic velocities for 18 campaign sites and have installed 10 additional sites in the backarc to investigate the nature of the transition from forearc sliver motion to stable Caribbean Plate motion. Our work focusing on the later issue is presented elsewhere at this meeting (Styron et al., 2007). Corrections for modeled coseismic offsets from the Jan. 13, 2001 Mw7.7 earthquake off the coast of El Salvador have been applied to our campaign site velocities. Some of our time-series are also strongly affected by coseismic and postseismic effects of the Oct. 9, 2004 Mw6.9 earthquake off of the coast of Nicaragua. The geodetic effects of this event are being removed from the affected time-series for interseismic velocity analysis. We have also derived interseismic velocities for five continuous GPS sites in the region. Our GPS results confirm previous predictions of northwest transport of a forearc sliver with an average Northwest velocity of ~15 mm yr-1, but show little evidence for an arc- normal component of strain accumulation associated with locking on the subduction interface. However, the amount of seismicity along this section of the Middle America Trench, including several recent large events such as the 1992 Mw7.6 and 2004 Mw6.9 earthquakes, indicates some amount of locking is present. Several possibilities may account for the apparent contradiction between the GPS results and observed seismicity. The locked zone may be too shallow and too far offshore for the arc-normal component to show up in our network, or the arc-normal signal may be masked by post-seismic effects from the 1992 offshore earthquake. If coupling between the downgoing slab and the overriding plate is weak or limited to a small seismogenic zone, then arc-parallel motion of the forearc sliver may be driven by a more strongly coupled region to the south in Costa Rica. We are developing regional FEM and half-space dislocation models constrained by the GPS-derived kinematics to distinguish between these possibilities and explore the possible driving mechanisms for sliver motion.

An Overview of Geodetic and Astrometric VLBI at the Hartebeesthoek Radio Astronomy Observatory

NASA Astrophysics Data System (ADS)

de Witt, A.; Gaylard, M.; Quick, J.; Combrinck, L.

2013-08-01

For astronomical Very Long Baseline Interferometry (VLBI), the Hartebeesthoek Radio Astronomy Observatory (HartRAO), in South Africa operates as part of a number of networks including the European and Australian VLBI networks, global arrays and also space VLBI. HartRAO is the only African representative in the international geodetic VLBI network and participates in regular astrometric and geodetic VLBI programmes. HartRAO will play a major role in the realization of the next generation full-sky celestial reference frame, especially the improvement of the celestial reference frame in the South. The observatory also provides a base for developing the African VLBI Network (AVN), a project to convert redundant satellite Earth-station antennas across Africa to use for radio astronomy. The AVN would greatly facilitate VLBI observations of southern objects. We present an overview of the current capabilities as well as future opportunities for astrometric and geodetic VLBI at HartRAO.

Space-geodetic Constraints on GIA Models with 3D Viscosity

NASA Astrophysics Data System (ADS)

Van Der Wal, W.; Xu, Z.

2012-12-01

Models for Glacial Isostatic Adjustment (GIA) are an important correction to observations of mass change in the polar regions. Inputs for GIA models include past ice thickness and deformation parameters of the Earth's mantle, both of which are imperfectly known. Here we focus on the latter by investigating GIA models with 3D viscosity and composite (linear and non-linear) flow laws. It was found recently that GIA models with a composite flow law result in a better fit to historic sea level data, but they predict too low present-day uplift rates and gravity rates. Here GIA models are fit to space-geodetic constraints in Fennoscandia and North America. The preferred models are used to calculate the magnitude of the GIA correction on mass change estimates in Greenland and Antarctica. The observations used are GRACE Release 4 solutions from CSR and GFZ and published GPS solutions for North America and Fennoscandia, as well as historic sea level data. The GIA simulations are performed with a finite element model of a spherical, self-gravitating, incompressible Earth with 2x2 degree elements. Parameters in the flow laws are taken from seismology, heatflow measurements and experimental constraints and the ice loading history is prescribed by ICE-5G. It was found that GRACE and GPS derived uplift rates agree at the level of 1 mm/year in North America and at a level of 0.5 mm/year in Fennoscandia, the difference between the two regions being due to larger GPS errors and under sampling in North America. It can be concluded that both GPS and GRACE see the same process and the effects of filtering, noise and non-GIA processes such as land hydrology are likely to be small. Two GIA models are found that bring present-day uplift rate close to observed values in North America and Fennoscandia. These models result in a GIA correction of -17 Gt/year and -26 Gt/year on Greenland mass balance estimates from GRACE.

Fortaleza Station Report for 2012

NASA Technical Reports Server (NTRS)

Kaufmann, Pierre; Pereira de Lucena, A. Macilio; Sombra da Silva, Adeildo

2013-01-01

This is a brief report about the activities carried out at the Fortaleza geodetic VLBI station (ROEN: R´adio Observat´orio Espacial do Nordeste), located in Eus´ebio, CE, Brazil, during the period from January until December 2012. The observing activities were resumed in May after the major maintenance that comprised the azimuth bearing replacement. The total observational experiments consisted of 103 VLBI sessions and continuous GPS monitoring recordings.

The interpretation of crustal dynamics data in terms of plate interactions and active tectonics of the Anatolian plate and surrounding regions in the Middle East

NASA Technical Reports Server (NTRS)

Toksoz, M. Nafi; Reilinger, Robert

1992-01-01

A detailed study was made of the consequences of the Arabian plate convergence against Eurasia and its effects on the tectonics of Anatolia and surrounding regions of the eastern Mediterranean. A primary source of information is time rates of change of baseline lengths and relative heights determined by repeated SLR measurements. These SLR observations are augmented by a network of GPS stations in Anatolia, Aegea, and Greece, established and twice surveyed since 1988. The existing SLR and GPS networks provide the spatial resolution necessary to reveal the details of ongoing tectonic processes in this area of continental collision. The effort has involved examining the state of stress in the lithosphere and relative plate motions as revealed by these space based geodetic measurements, seismicity, and earthquake mechanisms as well as the aseismic deformations of the plates from conventional geodetic data and geological evidence. These observations are used to constrain theoretical calculations of the relative effects of: (1) the push of the Arabian plate; (2) high topography of Eastern Anatolia; (3) the geometry and properties of African-Eurasian plate boundary; (4) subduction under the Hellenic Arc and southwestern Turkey; and (5) internal deformation and rotation of the Anatolian plate.

GPS Application for Groundwater Resource Assessment, Hermanus, South Africa

NASA Astrophysics Data System (ADS)

Hartnady, C.; Mlisa, A.; Wonnacott, R.; Calais, E.

2009-04-01

TrigNet (http://www.trignet.co.za/footprint/home.jsp) is a network of permanent continuously operating GPS (cGPS) base stations distributed throughout South Africa at approximately 200 - 300 km spacing. Data from 21 of the stations is continuously streamed to the TrigNet control centre in the offices of the Chief Directorate: Surveys and Mapping, from where it is made available within 30 minutes after each hour for 24 hours a day. All stations record 1-second epoch data on both GPS frequencies (L1 and L2) through geodetic-standard choke ring antennas. The real-time Trignet station HERM is situated in the grounds of the Hermanus Magnetic Observatory (HMO), in a coastal town about 100 km SW of the City of Cape Town. The Overstrand Municipality of the Greater Hermanus Area has embarked on a major groundwater development to augment the water supply. As a foundation for sustainable management of the groundwater resource, a detailed monitoring programme was developed for a better understanding of the hydraulic system, and of the interconnections between surface water, the shallow primary aquifer and the remarkable, deep, fractured-rock (FR) aquifer of the Table Mountain Group (TMG), which underlies a large part of the Western Cape province in South Africa. A thick, extensive FR aquifer system like the ~1 km thick Peninsula Aquifer in the TMG provides an opportunity for fundamental advances in understanding interactions between fluid flow and mechanical deformation, through analysis of the "hydro-mechanical" coupling in FR permeability, fluid transport and deep storage in FR porosity. Present knowledge of skeletal-framework compressibility, the main factor in specific storage, is based on published data from similar rocks elsewhere. Up-scaling from dry-sample laboratory measurements of elastic properties of borehole-core samples at ~10-cm scale to saturated rock volumes on 100- to 1000-m scale, is methodologically problematic. Measuring directly the compaction of, and corresponding surface subsidence above, the pumped aquifer, and using these field-experimental measurements to determine the framework compressibility and the specific storage, can obviate such problems. Historically, such aquifer-deformation measurements have used costly devices (borehole extensometers), but recent advances in GNSS technology (e.g., GPS), and also Interferometric Synthetic Aperture Radar (InSAR), now provide noninvasive methods of geospatial data collection, which can be used in conjunction with borehole hydrograph information to estimate the specific storage and hydraulic conductivity of the aquifers. We have now established a local network of three new cGPS stations on the borehole infrastructure of the Gateway Wellfield at Hermanus, for the purpose of quantifying the vertical and horizontal surface deformations related to groundwater abstraction, prior to a phase of aquifer test-pumping that will begin early in 2009. This African project contributes to the IGCP Project 565 effort to develop the Global Geodetic Observation System (GGOS) towards a global-to-regional-scale monitoring of the full hydrological cycle. It supports capacity-building in space-geodetic data-processing, modeling of the hydrological cycle, and interpretation of observations in terms of terrestrial water storage.

Development of GPS/A Seafloor Geodetic Network Along Japan Trench and Onset of Its Operation

NASA Astrophysics Data System (ADS)

Kido, M.; Fujimoto, H.; Osada, Y.; Ohta, Y.; Yamamoto, J.; Tadokoro, K.; Okuda, T.; Watanabe, T.; Nagai, S.; Kenji, Y.

2012-12-01

The Tohoku-oki earthquake in 2011 revealed that an M9-class giant earthquake could occur even in the old subduction zone and that coseismic slip can reach its frontal wedge, where we considered no significant stress had been accumulated in. One of the leading figure of such finding is in situ seafloor geodetic measurement, such as GPS/A technique for horizontal displacement and pressure gauge for vertical displacement. Japan Coast Guard and Japanese university group had developed several GPS/A sites near the source region of the Tohoku-oki earthquake and detected quite large coseismic movements over 20 m in there. Displacement vectors observed these sites showed systematic variation, i.e., mainly confined in the off-Miyagi area and getting larger near the trench. However, subsequent post-seismic deformation shows inexplicable distribution. In order to elucidate this complex feature, MEXT Japan has decided to construct dense and widely-extended GPS/A network along Japan trench, including deep area (~6000m). We, Tohoku and Nagoya universities, have firstly developed high-powered seafloor transponders with an omnidirectional acoustic unit that works at 6000 m deep ocean and enable acoustic ranging over 13 km slant length. In addition, using high-energy density battery, its lifetime is expected 10 years with normal operation. Secondly, we examined the optimal distribution of GPS/A sites forming a network, taken pre-existing sites into consideration. The new network consists of 20 sites (roughly four transponders at a single site and 86 transponders in total). The distribution is dense near the area of complex post-seismic deformation and extended over 400 km to cover the adjacent area of the source region, in where induced earthquake may be expected. The largest obstacle to draw network plan is seafloor topography. Because a GPS/A site is a seafloor benchmark, its installation must be on flat and locally stable spot. Since a single GPS/A site consists of three or more transponders in an area extending roughly the same dimension of its depth, flat spot is quite limited especially near the trench. The positions of the 20 sites were carefully determined using a high-definition bathymetry map. We already have constructed two sites, one of which is 5500 m depth, and successfully obtained acoustic data. In September, we will install rest of the sites (18 sites) and begin initial campaign survey. The second campaign is planned in November. We will introduce details of the network and report updated result in the talk.

Egnos Limitations over Central and Eastern Poland - Results of Preliminary Tests of Egnos-Eupos Integration Project

NASA Astrophysics Data System (ADS)

Jaworski, Leszek; Swiatek, Anna; Zdunek, Ryszard

2013-09-01

The problem of insufficient accuracy of EGNOS correction for the territory of Poland, located at the edge of EGNOS range is well known. The EEI PECS project (EGNOS EUPOS Integration) assumes improving the EGNOS correction by using the GPS observations from Polish ASG-EUPOS stations. One of the EEI project tasks was the identification of EGNOS performance limitations over Poland and services for EGNOSS-EUPOS combination. The two sets of data were used for those goals: statistical, theoretical data obtained using the SBAS simulator software, real data obtained during the measurements. The real measurements were managed as two types of measurements: static and dynamic. Static measurements are continuously managing using Septentrio PolaRx2 receiver. The SRC permanent station works in IMAGE/PERFECT project. Dynamic measurements were managed using the Mobile GPS Laboratory (MGL). Receivers (geodetic and navigation) were working in two modes: determining navigation position from standalone GPS, determining navigation position from GPS plus EGNOS correction. The paper presents results of measurements' analyses and conclusions based on which the next tasks in EEI project are completed

Stability characterization of two multi-channel GPS receivers for accurate frequency transfer.

NASA Astrophysics Data System (ADS)

Taris, F.; Uhrich, P.; Thomas, C.; Petit, G.; Jiang, Z.

In recent years, wide-spread use of the GPS common-view technique has led to major improvements, making it possible to compare remote clocks at their full level of performance. For integration times of 1 to 3 days, their frequency differences are consistently measured to about one part in 1014. Recent developments in atomic frequency standards suggest, however, that this performance may no longer be sufficient. The caesium fountain LPTF FO1, built at the BNM-LPTF, Paris, France, shows a short-term white frequency noise characterized by an Allen deviation σy(τ = 1 s) = 5×10-14 and a type B uncertainty of 2×10-15. To compare the frequencies of such highly stable standards would call for GPS common-view results to be averaged over times far exceeding the intervals of their optimal performance. Previous studies have shown the potential of carrier-phase and code measurements from geodetic GPS receivers for clock frequency comparisons. The experiment related here is an attempt to see the stability limit that could be reached using this technique.

Is Interseismic Deformation along the Sumatra Subduction Zone Ever 'Stable'?

NASA Astrophysics Data System (ADS)

Hill, E.; Meltzner, A. J.; Moore, J. D. P.; Philibosian, B.; Feng, L.; Lindsey, E. O.; Bradley, K. E.; Qiu, Q.

2017-12-01

Estimates of megathrust coupling ratios are regularly calculated using geodetic data then used to forecast seismic and tsunami hazard. Given that the geodetic data capture only a small snapshot in time, an important question is the extent to which these accurately reflect long-term strain build up. We analyze this question using the Sumatra subduction zone as a case study. Here we have 15 years of continuous GPS data, with some collected before the recent great earthquake sequence started in 2004, and most collected afterwards. We also have paleogeodetic data from coral microatolls dating back over many earthquake supercycles (sequences of great earthquakes that are clustered in time). The coral data indicate significant changes in interseismic deformation rates over time for the Sunda megathrust; these could result from spontaneous changes in the spatial distribution of megathrust locking, from coseismically induced changes in locking, or from long-term viscoelastic processes. One question we ask is whether in Sumatra a transient rheology with high steady-state viscoelastic relaxation times, coupled with a relatively short recurrence interval for the supercycles (as little as 200 years), results in a situation where interseismic rates evolve throughout the entire earthquake cycle. To illustrate, a GPS station in northern Sumatra has been rapidly uplifting since 2004 at rates of 3 cm/yr; we do not know when this will slow down, but if this is a small piece of a viscoelastic decay curve it seems likely that the relaxation time is very long, and a geodetic snapshot at any point in many decades to come will not be representative of long-term average rates. We also consider whether there is a fundamental difference between viscoelastic behavior for megathrusts and strike-slip faults, with the former driving much longer, broader-scale deformation patterns that have more influence over the interseismic period. Indeed, the nearby strike-slip Sumatran Fault does appear to have agreement between geodetic and geologic rates; what the feedbacks are between interseismic deformation for this and the Sunda megathrust are yet to be discovered.

GPS and InSAR Observations of Active Mountain Growth Across the Sierra Nevada/Great Basin Transition

NASA Astrophysics Data System (ADS)

Hammond, W. C.; Blewitt, G.; Li, Z.; Kreemer, C. W.; Plag, H.

2010-12-01

Topographic relief across the Sierra Nevada Mountains and Great Basin of the western United States is dominated by mountain ranges and valleys that are the product of active tectonic deformation. The contemporary rate of uplift of the Sierra Nevada via slip on range front faults and/or tilting of the Sierra Nevada/Great Valley microplate (SNGV) has been the subject of controversy. For example, geologic estimates of the age of the modern range topography vary by one order of magnitude, from 3 to 30 million years. With present elevations near 3 km, the more rapid of these implied rates is large enough to be detected by the most precise GPS measurements. We use GPS vertical and horizontal components, and InSAR time series analysis to address these long standing questions about the rates of Sierran uplift. The data are from western U.S. high precision GPS networks including the EarthScope Plate Boundary Observatory, its nucleus networks, the University of Nevada Mobile Array of GPS for Nevada Transtension, and from integrated InSAR+GPS time series analysis of ERS and ENVISAT scenes acquired between 1992 and 2010 from the GeoEarthScope and WinSAR data archives. GPS data are processed using the GIPSY OASIS II software, with ambiguities resolved, ocean tidal loading, latest GMF troposphere model and antenna calibrations applied. InSAR time series analysis results provide enhanced geographic resolution, improving our ability to locate the boundary of SNGV block-like behavior. Vertical velocities from long-running continuous stations in eastern Nevada are very similar to one another, averaging -0.1 mm/yr, with standard deviation of 0.27 mm/yr, placing an upper bound on the uncertainty in vertical rates. We find agreement between the results of InSAR time series analysis aligned to GPS and GPS line of site rates at the level of 0.35 mm/yr, placing an upper bound on the uncertainty of InSAR time series results. Because we seek to infer long-term uplift rates, applicable over millions of years, we correct the geodetic velocity field for postseismic transients from earthquakes that can cause long-wavelength distortions of the GPS velocity field. The signal of viscoelastic relaxation from historic earthquakes in Central Nevada is clearly visible in the data. We remove this transient relaxation by subtracting the predictions from a published model, although the effect on SNGV vertical motion is negligible. There is general agreement among stations on the west slope of the Sierra Nevada, near the central and southern Sierra between latitude 36° and 39°, that the rates are between 0.8 and 1.6 mm/yr upward with respect to eastern Nevada. These rates are in broad agreement with normal slip rates on the range front faults along the eastern edge of the SNGV estimated using block models constrained by horizontal GPS measurements. Thus our results agree with models that call for a Sierra Nevada uplift rate near 1 mm/yr, and a younger Sierra Nevada whose age is on the order of 3 Ma.

Options for developing modernized geodetic datum for Nepal following the April 25, 2015 Mw7.8 Gorkha earthquake

NASA Astrophysics Data System (ADS)

Pearson, Chris; Manandhar, Niraj; Denys, Paul

2017-09-01

Along with the damage to buildings and infrastructure, the April 25, 2015 Mw7.8 Gorkha earthquake caused significant deformation over a large area of eastern Nepal with displacements of over 2 m recorded in the vicinity of Kathmandu. Nepal currently uses a classical datum developed in 1984 by the Royal (UK) Engineers in collaboration with the Nepal Survey Department. It has served Nepal well; however, the recent earthquakes have provided an impetus for developing a semi-dynamic datum that will be based on ITRF2014 and have the capacity to correct for tectonic deformation. In the scenario we present here, the datum would be based on ITRF2014 with a reference epoch set some time after the end of the current sequence of earthquakes. The deformation model contains a grid of the secular velocity field combined with models of the Gorkha Earthquake and the May 12 Mw7.3 aftershock. We have developed a preliminary velocity field by collating GPS derived crustal velocities from four previous studies for Nepal and adjacent parts of China and India and aligning them to the ITRF. Patches for the co-seismic part of the deformation for the Gorkha earthquake and the May 12, 2015 Mw 7.2 aftershock are based on published dislocation models. High order control would be a CORS network based around the existing Nepal GPS Array. Coordinates for existing lower order control would be determined by readjusting existing survey measurements and these would be combined with a series of new control stations spread throughout Nepal.

Analysis of orbital configurations for geocenter determination with GPS and low-Earth orbiters

NASA Astrophysics Data System (ADS)

Kuang, Da; Bar-Sever, Yoaz; Haines, Bruce

2015-05-01

We use a series of simulated scenarios to characterize the observability of geocenter location with GPS tracking data. We examine in particular the improvement realized when a GPS receiver in low Earth orbit (LEO) augments the ground network. Various orbital configurations for the LEO are considered and the observability of geocenter location based on GPS tracking is compared to that based on satellite laser ranging (SLR). The distance between a satellite and a ground tracking-site is the primary measurement, and Earth rotation plays important role in determining the geocenter location. Compared to SLR, which directly and unambiguously measures this distance, terrestrial GPS observations provide a weaker (relative) measurement for geocenter location determination. The estimation of GPS transmitter and receiver clock errors, which is equivalent to double differencing four simultaneous range measurements, removes much of this absolute distance information. We show that when ground GPS tracking data are augmented with precise measurements from a GPS receiver onboard a LEO satellite, the sensitivity of the data to geocenter location increases by more than a factor of two for Z-component. The geometric diversity underlying the varying baselines between the LEO and ground stations promotes improved global observability, and renders the GPS technique comparable to SLR in terms of information content for geocenter location determination. We assess a variety of LEO orbital configurations, including the proposed orbit for the geodetic reference antenna in space mission concept. The results suggest that a retrograde LEO with altitude near 3,000 km is favorable for geocenter determination.

Mapping the Coastline Limits of the Mexican State Sinaloa Using GPS

NASA Astrophysics Data System (ADS)

Vazquez, G. E.

2007-12-01

This research work presents the delimitation of the coastline limits of Sinaloa (one of the richest states of northwestern Mexico). In order to achieve this big task, it was required to use GPS (Global Positioning System) together with leveling spirit measurements. Based on the appropriate selection of the cited measurement techniques, the objective was to map the Sinaloa's state coastline to have the cartography of approximate 1600 km of littoral. The GPS measurements were performed and referred with respect to a GPS network located across the state. This GPS network consists of at least one first-order-site at each of the sixteen counties that constitute the state, and three to four second-order-sites of the ten counties of the state surrounded by sea. The leveling spirit measurements were referred to local benchmarks pre-established by the Mexican agency SEMARNAT (SEcretaría Del Medio Ambiente y Recursos NATurales). Within the main specifications of the GPS measurements and equipment, we used geodetic-dual-frequency GPS receivers in kinematic mode for both base stations (first and second order sites of the GPS state network) and rover stations (points forming the state littoral) with 5-sec log-rate interval and 10 deg cut-off angle. The GPS data processing was performed using the commercial software Trimble Geomatics Office (TGO) with Double Differences (DD) in post-processing mode. To this point, the field measurements had been totally covered including the cartography (scale 1:1000) and this includes the specifications and appropriate labeling according to the Mexican norm NOM-146-SEMARNAT-2005.

GPS Array as a Sensor of Lithosphere, Troposphere and Ionosphere

NASA Astrophysics Data System (ADS)

Heki, K.

2011-12-01

The Japanese dense array of GPS receivers (GEONET) started operation in 1993, and is currently composed of ~1200 stations. GPS (or GNSS in general) receivers can be compared to a Swiss army knife: it could be used not only for positioning (a knife) but also for various purposes, e.g. remote sensing of tropospheric water vapor or ionospheric electrons (screw driver, tin opener etc). Dense GPS arrays have been found extremely useful for variety of geophysical studies. In this lecture, I briefly review their historical achievements, recent highlights, and future perspectives. In Japan, first generation GPS stations were implemented in 1993 (the Kanto-Tokai region) and 1994 (nationwide) by GSI, Japan. Shortly after the launch, they successfully caught coseismic crustal movement of several major earthquakes, the 1994 October Shikotan (Mw8.3), the 1994 December Sanriku (Mw7.6), and the 1995 January Kobe (Mw7.0) earthquakes. These earthquakes accelerated the densification of the GPS network, achieving 1000 in the number of stations within the following 2-3 years. In addition to coseismic jumps, important discoveries continued in 1990s, e.g. large-scale afterslip of interplate thrust earthquakes and slow slip events (SSE). Later it was shown that tilt- and strainmeter can better observe short-term SSEs, and InSAR can draw more detailed maps of coseismic crustal movements. Now GPS array is recognized as a good tool to measure crustal movement with high temporal resolution and stability and with moderate sensitivity and spatial resolution. GPS data are also useful to study hydrosphere. Seasonal crustal movements in Japan mainly reflect changes in hydrological loads. Multipath signatures in GPS data also provide useful information on the environment around the antenna, e.g. soil moisture, snow depth and vegetation. I will compare the snow depth record over a winter inferred by analyzing GPS multipath signatures, and observed by a conventional apparatus. GPS can also measure precipitable water vapor (PWV) of troposphere. After intense feasibility studies of GPS meteorology in 1990s, PWV information from GEONET has been routinely assimilated in the operational mesoscale model of the Japan Meteorological Agency since 2009. It is found useful in predicting localized heavy rainfalls that often attack Japan in summer. It is fairly easy to measure ionospheric total electron content (TEC) by using phase differences between L1 and L2 carriers from GPS satellites. Applications of GPS for upper atmospheric studies started for ionospheric disturbances of space weather origins. In 2003, clear coseismic ionospheric disturbances of the Tokachi-Oki earthquake were found, and the GPS-TEC technique has been extensively used to study ionospheric disturbances of solid earth origins, e.g. earthquakes and volcanic eruptions. There are also several recent examples of artificial ionospheric disturbances caused by rocket launches and passage of ballistic missiles from North Korea above NE Japan. In the last part of the lecture, I summarize what the GPS array saw before, during and after the 2011 Tohoku-Oki earthquake. The topic covers not only pre-, co- and postseismic crustal movements, but also results of high-rate sampling, and possible detection of precursory changes in ionospheric TEC immediately before the earthquake.

Real-Time GNSS Positioning with JPL's new GIPSYx Software

NASA Astrophysics Data System (ADS)

Bar-Sever, Y. E.

2016-12-01

The JPL Global Differential GPS (GDGPS) System is now producing real-time orbit and clock solutions for GPS, GLONASS, BeiDou, and Galileo. The operations are based on JPL's next generation geodetic analysis and data processing software, GIPSYx (also known at RTGx). We will examine the impact of the nascent GNSS constellations on real-time kinematic positioning for earthquake monitoring, and assess the marginal benefits from each constellation. We will discus the options for signal selection, inter-signal bias modeling, and estimation strategies in the context of real-time point positioning. We will provide a brief overview of the key features and attributes of GIPSYx. Finally we will describe the current natural hazard monitoring services from the GDGPS System.

Application of Raytracing Through the High Resolution Numerical Weather Model HIRLAM for the Analysis of European VLBI

NASA Technical Reports Server (NTRS)

Garcia-Espada, Susana; Haas, Rudiger; Colomer, Francisco

2010-01-01

An important limitation for the precision in the results obtained by space geodetic techniques like VLBI and GPS are tropospheric delays caused by the neutral atmosphere, see e.g. [1]. In recent years numerical weather models (NWM) have been applied to improve mapping functions which are used for tropospheric delay modeling in VLBI and GPS data analyses. In this manuscript we use raytracing to calculate slant delays and apply these to the analysis of Europe VLBI data. The raytracing is performed through the limited area numerical weather prediction (NWP) model HIRLAM. The advantages of this model are high spatial (0.2 deg. x 0.2 deg.) and high temporal resolution (in prediction mode three hours).

Improvement of real-time seismic magnitude estimation by combining seismic and geodetic instrumentation

NASA Astrophysics Data System (ADS)

Goldberg, D.; Bock, Y.; Melgar, D.

2017-12-01

Rapid seismic magnitude assessment is a top priority for earthquake and tsunami early warning systems. For the largest earthquakes, seismic instrumentation tends to underestimate the magnitude, leading to an insufficient early warning, particularly in the case of tsunami evacuation orders. GPS instrumentation provides more accurate magnitude estimations using near-field stations, but isn't sensitive enough to detect the first seismic wave arrivals, thereby limiting solution speed. By optimally combining collocated seismic and GPS instruments, we demonstrate improved solution speed of earthquake magnitude for the largest seismic events. We present a real-time implementation of magnitude-scaling relations that adapts to consider the length of the recording, reflecting the observed evolution of ground motion with time.

A small hemispherical helical antenna array for two-dimensional GPS beam-forming

NASA Astrophysics Data System (ADS)

Hui, H. T.; Aditya, S.; Mohamed, F. Bin S.; Hafiedz-Ul, A. Bin T.

2005-02-01

A small hemispherical helical antenna array with multibeam output for GPS beam-forming is designed and characterized. A Butler matrix beam-forming network is designed to provide four spatial beams in a two-dimensional directional space. The original design of the hemispherical helical antenna elements is modified in order to match it to the system impedance. Our study shows that even after an ˜30° scan from the normal direction, the maximum change in beam width is only 6°, the maximum change in axial ratio is 1.4 dB, and the maximum change in power gain is 1.1 dB. These characteristics indicate that the array can be potentially used for GPS beam-forming.

Present day vertical deformation of Pico and Faial islands revealed by merged INSAR and GPS data

NASA Astrophysics Data System (ADS)

Catalao, Joao; Nico, Giovanni; Catita, Cristina

2010-05-01

In this paper we investigate the problem of the integration of repeated GPS geodetic measurements and interferometric Synthetic Aperture Radar (SAR) observations for the determination of high resolution vertical deformation maps. The Faial and Pico islands in the Azores archipelago were chosen as study area. These islands are characterized by a intense volcanic and seismic activity. Both islands are covered by huge vegetation and have very unstable atmospheric conditions which negatively influence the interferometric processing. In this work, we apply the advanced interferometric SAR processing based on Persistent Scatterers. However, the small number of man made structures reduces the density of Persistent Scatterers. Furthermore, the different ascending and descending acquisition geometries give different sets of Persistent Scatterers, with complementary spatial coverage, and different line-of-sight velocities. The estimated velocities are relative to the master image (different from ascending and descending) and must be referred to an absolute velocity (in the sense of referred to a geodetic reference frame). The strategy used to overcome the aforementioned problems is based on the combination of sparse GPS 3D-velocities with two sets of Persistent Scatterers determined from ascending and descending passes. The input data are: a set of GPS - 3D velocities relative to ITRF05 (18 Stations) and two sets of Persistent Scatterers corresponding to the descending and ascending orbits. A dataset of 60 interferometric repeat-pass ASAR/ENVISAT images were acquired over the Faial and Pico islands, from 2006 to 2008, along ascending and descending passes. Each interferogram obtained by this dataset was corrected for atmospheric artefacts using a Weather Forecasting model. Initially, the horizontal velocity component (east and north) is assigned to each PS from interpolation of available GPS observations. Then, the vertical component of the velocity is determined from the SAR line-of-sight velocity and the GPS horizontal velocity component. Later, the vertical velocity offsets are numerically determined by comparison between GPS (ITRF velocities) and PS (the two ascending and descending sets) measurements. These values are then used to create the vertical deformation map of Faial and Pico islands with considerably better resolution and accuracy than using a single set of observations. The vertical deformation map has identified a large continuous area of subsidence on the west of Faial island, on the flank of Capelinhos eruption cone, with a maximum subsidence range of 10 mm/yr. It has also revealed the subsidence of the summit crater of Pico island (9 mm/yr) and a large area of subsidence on the west of the island, corresponding mostly to creep movement. Key words: SAR Interferometry, GPS-INSAR integration, Volcano, subsidence

A Cost-Effective Geodetic Strainmeter Based on Dual Coaxial Cable Bragg Gratings

PubMed Central

Fu, Jihua; Wang, Xu; Wei, Tao; Wei, Meng; Shen, Yang

2017-01-01

Observations of surface deformation are essential for understanding a wide range of geophysical problems, including earthquakes, volcanoes, landslides, and glaciers. Current geodetic technologies, such as global positioning system (GPS), interferometric synthetic aperture radar (InSAR), borehole and laser strainmeters, are costly and limited in their temporal or spatial resolutions. Here we present a new type of strainmeters based on the coaxial cable Bragg grating (CCBG) sensing technology that provides cost-effective strain measurements. Two CCBGs are introduced into the geodetic strainmeter: one serves as a sensor to measure the strain applied on it, and the other acts as a reference to detect environmental noises. By integrating the sensor and reference signals in a mixer, the environmental noises are minimized and a lower mixed frequency is obtained. The lower mixed frequency allows for measurements to be taken with a portable spectrum analyzer, rather than an expensive spectrum analyzer or a vector network analyzer (VNA). Analysis of laboratory experiments shows that the strain can be measured by the CCBG sensor, and the portable spectrum analyzer can make measurements with the accuracy similar to the expensive spectrum analyzer, whose relative error to the spectrum analyzer R3272 is less than ±0.4%. The outputs of the geodetic strainmeter show a linear relationship with the strains that the CCBG sensor experienced. The measured sensitivity of the geodetic strainmeter is about −0.082 kHz/με; it can cover a large dynamic measuring range up to 2%, and its nonlinear errors can be less than 5.3%. PMID:28417925

A Cost-Effective Geodetic Strainmeter Based on Dual Coaxial Cable Bragg Gratings.

PubMed

Fu, Jihua; Wang, Xu; Wei, Tao; Wei, Meng; Shen, Yang

2017-04-12

Observations of surface deformation are essential for understanding a wide range of geophysical problems, including earthquakes, volcanoes, landslides, and glaciers. Current geodetic technologies, such as global positioning system (GPS), interferometric synthetic aperture radar (InSAR), borehole and laser strainmeters, are costly and limited in their temporal or spatial resolutions. Here we present a new type of strainmeters based on the coaxial cable Bragg grating (CCBG) sensing technology that provides cost-effective strain measurements. Two CCBGs are introduced into the geodetic strainmeter: one serves as a sensor to measure the strain applied on it, and the other acts as a reference to detect environmental noises. By integrating the sensor and reference signals in a mixer, the environmental noises are minimized and a lower mixed frequency is obtained. The lower mixed frequency allows for measurements to be taken with a portable spectrum analyzer, rather than an expensive spectrum analyzer or a vector network analyzer (VNA). Analysis of laboratory experiments shows that the strain can be measured by the CCBG sensor, and the portable spectrum analyzer can make measurements with the accuracy similar to the expensive spectrum analyzer, whose relative error to the spectrum analyzer R3272 is less than ±0.4%. The outputs of the geodetic strainmeter show a linear relationship with the strains that the CCBG sensor experienced. The measured sensitivity of the geodetic strainmeter is about -0.082 kHz/με; it can cover a large dynamic measuring range up to 2%, and its nonlinear errors can be less than 5.3%.

Current crustal deformation of the Taiwan orogen reassessed by cGPS strain-rate estimation and focal mechanism stress inversion

NASA Astrophysics Data System (ADS)

Chen, Sean Kuanhsiang; Wu, Yih-Min; Hsu, Ya-Ju; Chan, Yu-Chang

2017-07-01

We study internal deformation of the Taiwan orogen, a young arc-continental collision belt, which the spatial heterogeneity remains unclear. We aim to ascertain heterogeneity of the orogenic crust in depth when specifying general mechanisms of the Taiwan orogeny. To reach this goal, we used updated data of continuous GPS (cGPS) and earthquake focal mechanisms to reassess geodetic strain-rate and seismic stress fields of Taiwan, respectively. We updated the both data sets from 1990 to 2015 to provide large amount of constraints on surficial and internal deformation of the crust for a better understanding. We estimated strain-rate tensors by calculating gradient tensors of cGPS station velocities in horizontal 0.1°-spacing grids via Delaunay triangulation. We determined stress tensors within a given horizontal and vertical grid cell of 0.1° and 10 km, respectively, by employing the spatial and temporal stress inversion. To minimize effects of the 1999 Mw 7.6 Chi-Chi earthquake on trends of the strain and stress, we modified observational possible bias of the cGPS velocities after the earthquake and removed the first 15-month focal mechanisms within the fault rupture zone. We also calculated the Anderson fault parameter (Aϕ) based on stress ratios and rake angles to quantitatively describe tectonic regimes of Taiwan. By examining directions of seismic compressive axes and styles of faulting, our results indicate that internal deformation of the crust is presently heterogeneous in the horizontal and vertical spaces. Directions of the compressive axes are fan-shaped oriented between N10°W and N110°W in the western and mid-eastern Taiwan at the depths of 0-20 km and near parallel to orientations of geodetic compressional axes. The orientations agreed with predominantly reverse faulting in the western Taiwan at the same depth range, implying a brittle deformation regime against the Peikang Basement High. Orientations of the compressive axes most rotated counter-clockwise at the depths of 20-40 km, coinciding with transition of styles of faulting from reverse to strike-slip faulting along the depths as revealed by variation of the Aϕ values. The features indicate that internal deformation of the upper crust is primarily driven by the same compressional mechanism. It implies that geodetic strains could detect the deformation from surface down to a maximal depth of 20 km in most regimes of Taiwan. We find that heterogeneity in orientations of compressive axes and styles of faulting is strong in two regimes at the northern and southern Central Range, coinciding to areas of the orogenic thinned/thickened crust. Conversely, the heterogeneity is weak in the central Western Foothills at surrounding area of root of the overthickened crust. This observation, coupled with regional seismological observations, may imply that vertical deformation from crustal thickening and thinning and thinning-related dynamics from mantle flows may have joint influence on degree of stress heterogeneity.

A New Global Geodetic Strain Rate Model

NASA Astrophysics Data System (ADS)

Kreemer, C.; Blewitt, G.; Klein, E. C.; Shen, Z.; Wang, M.; Estey, L.; Wier, S.

2013-12-01

As part of the Global Earthquake Model (GEM) effort to improve global seismic hazard models, we present a new global geodetic strain rate model. This model (GSRM v. 2) is a vast improvement on the previous model from 2004 (v. 1.2). The model is still based on a finite-element type approach and has deforming cells in between the assumed rigid plates. The new model contains ~144,700 cells of 0.25° by 0.2° dimension. We redefined the geometries of the deforming zones based on the definitions of Bird (2003) and Chamot-Rooke and Rabaute (2006). We made some adjustments to the grid geometry at places where seismicity and/or GPS velocities suggested either the presence of deforming areas or a rigid block where those previous studies did not. GSRM v.2 includes 50 plates and blocks, including many not considered by Bird (2003). The new GSRM model is based on over 20,700 horizontal geodetic velocities at over 17,000 unique locations. The GPS velocity field consists of a 1) Over 6500 velocities derived by the University of Nevada, Reno, for CGPS stations for which >2.5 years of RINEX data are available until April 2013, 2) ~1200 velocities for China from a new analysis of all data from the Crustal Movement Network of China (CMONOC), and 3) about 13,000 velocities from 212 studies published in the literature or made otherwise available to us. Velocities from all studies were combined into the same reference frame by a 6-parameter transformation using velocities at collocated stations. We model co-seismic jumps while estimating velocities, ignore periods of post-seismic deformation, and exclude time-series that reflect magmatic and anthropogenic activity. GPS velocities were used to estimate angular velocities for 36 of the 50 rigid plates and blocks (the rest being taken from the literature), and these were used as boundary conditions in the strain rate calculations. For the strain rate calculations we used the method of Haines and Holt. In order to fit the data equally well in slowly and rapidly deforming areas, we first calculated a very smooth model by setting the a priori variances of the strain rate components very low. We then used this model as a proxy for the a priori standard deviations of the final model, at least for the areas that are well constrained by the GPS data. We will show examples of the strain rate and velocity field results. We will also highlight how and where the results can be viewed and accessed through a dedicated webportal (gsrm2.unavco.org). New GPS velocities (in any reference frame) can be uploaded to a new tool and displayed together with velocities used in GSRM v.2 in 53 reference frames (http://facility.unavco.org/data/maps/GPSVelocityViewer/GSRMViewer.html) .

Impact of different NWM-derived mapping functions on VLBI and GPS analysis

NASA Astrophysics Data System (ADS)

Nikolaidou, Thalia; Balidakis, Kyriakos; Nievinski, Felipe; Santos, Marcelo; Schuh, Harald

2018-06-01

In recent years, numerical weather models have shown the potential to provide a good representation of the electrically neutral atmosphere. This fact has been exploited for the modeling of space geodetic observations. The Vienna Mapping Functions 1 (VMF1) are the NWM-based model recommended by the latest IERS Conventions. The VMF1 are being produced 6 hourly based on the European Centre for Medium-Range Weather Forecasts operational model. UNB-VMF1 provide meteorological parameters aiding neutral atmosphere modeling for VLBI and GNSS, based on the same concept but utilizing the Canadian Meteorological Centre model. This study presents comparisons between the VMF1 and the UNB-VMF1 in both delay and position domains, using global networks of VLBI and GPS stations. It is shown that the zenith delays agree better than 3.5 mm (hydrostatic) and 20 mm (wet) which implies an equivalent predicted height error of less than 2 mm. In the position domain and VLBI analysis, comparison of the weighted root-mean-square error (wrms) of the height component showed a maximum difference of 1.7 mm. For 48% of the stations, the use of VMF1 reduced the height wrms of the stations by 2.6% on average compared to a respective reduction of 1.7% for 41% of the stations employing the UNB-VMF1. For the subset of VLBI stations participating in a large number of sessions, neither mapping function outranked the other. GPS analysis using Precise Point Positioning had a sub-mm respective difference, while the wrms of the individual solutions had a maximum value of 12 mm for the 1-year-long analysis. A clear advantage of one NWM over the other was not shown, and the statistics proved that the two mapping functions yield equal results in geodetic analysis.

Indicator saturation: a novel approach to detect multiple breaks in geodetic time series.

NASA Astrophysics Data System (ADS)

Jackson, L. P.; Pretis, F.; Williams, S. D. P.

2016-12-01

Geodetic time series can record long term trends, quasi-periodic signals at a variety of time scales from days to decades, and sudden breaks due to natural or anthropogenic causes. The causes of breaks range from instrument replacement to earthquakes to unknown (i.e. no attributable cause). Furthermore, breaks can be permanent or short-lived and range at least two orders of magnitude in size (mm to 100's mm). To account for this range of possible signal-characteristics requires a flexible time series method that can distinguish between true and false breaks, outliers and time-varying trends. One such method, Indicator Saturation (IS) comes from the field of econometrics where analysing stochastic signals in these terms is a common problem. The IS approach differs from alternative break detection methods by considering every point in the time series as a break until it is demonstrated statistically that it is not. A linear model is constructed with a break function at every point in time, and all but statistically significant breaks are removed through a general-to-specific model selection algorithm for more variables than observations. The IS method is flexible because it allows multiple breaks of different forms (e.g. impulses, shifts in the mean, and changing trends) to be detected, while simultaneously modelling any underlying variation driven by additional covariates. We apply the IS method to identify breaks in a suite of synthetic GPS time series used for the Detection of Offsets in GPS Experiments (DOGEX). We optimise the method to maximise the ratio of true-positive to false-positive detections, which improves estimates of errors in the long term rates of land motion currently required by the GPS community.

Preliminary results on the current tectonic setting of South Georgia Island from GPS geodetic data.

NASA Astrophysics Data System (ADS)

Matheny, P.; Smalley, R., Jr.; Dalziel, I. W. D.; Lawver, L. A.; Gomez, D.; Teferle, F. N.; Hunegnaw, A.; Abraha, K. E.

2017-12-01

The South Georgia microcontinent is an allochthonous block from the south eastern part of Tierra del Fuego of South America that has been transported over the past 80-100 My as part of the development of the Scotia Plate. While the trajectory to its current position is poorly constrained, the microcontinent is now part of the eastern end of the North Scotia Ridge between the South America and the Scotia Plates almost 1600 km east of its original position. Based on bathymetric morphology and geological history of the Scotia Arc the microcontinent has been considered to be part of the Scotia Plate, with the plate boundary continuing along the North Scotia Ridge on the north side of the microcontinent, to the east where it transitions into the South Sandwich subduction boundary. Seismic activity in the region, while very low, is concentrated along the southern border of the microcontinent. This seismicity has been interpreted, based on a few small events with thrust mechanisms, to represent underthrusting and uplift of the island on a restraining bend in the North Scotia Ridge geometry to the north-east of the microcontinent. More recently, based on the seismicity distribution, the plate boundary has been placed along the south side of the microcontinent, suggesting that it has, or is being, transferred to the South America plate. In order to address the current tectonic affinity of South Georgia a four station continuous GPS network was installed on South Georgia Island to determine the block's relative motion with respect to the South America and Scotia Plates. The question is whether it is now attached to either plate or is an independent platelet, and whether it is suffering internal deformation. We will present the preliminary geodetic results based on 3 years of continuous GPS data.

Time dependence of volcano inflation: mass influx or viscoelastic relaxation? Insights from Grímsvötn volcano, Iceland

NASA Astrophysics Data System (ADS)

Segall, P.

2017-12-01

Distinguishing magma chamber pressurization from relaxation of a viscoelastic aureole surrounding the chamber based on geodetic measurements has remained challenging. Elastic models with mass inflow proportional to the pressure difference between the chamber and a deep reservoir predict exponentially decaying flux. For a spherical chamber surrounded by a Maxwell viscoelastic shell with pressure dependent recharge, the surface deformation is the sum of two exponentials (Segall, 2016). GPS displacements following eruptions of Grímsvötn, Iceland in 2004 and 2011 exhibit rapid post-eruptive inflation (time scale of 0.1 yr), followed by inflation with a much longer time constant. Markov Chain Monte Carlo inversion with the viscoelastic model shows the GPS time series can be fit with viscosity of 2e16 Pa-s, and a relatively incompressible magma, B = beta_c/ (beta_m + beta_c) > 0.6, where beta_m and beta_c are chamber and magma compressibility. The latter appears to conflict with the ratio of erupted volume to geodetically inferred source volume change, rv 10, obtained for the best fitting spherical (Mogi ) source (Hreinsdóttir, 2014). Since rv = 1/B, this implies a relatively compressible melt, B 0.1. Reexamination of the co-eruptive GPS and tilt data with the more general ellipsoidal model of Cervelli (2013), reveals that the best fitting sources are oblate (b/a 3), deeper, and with larger volume changes, rv 3, relative to spherical models. Oblate magma chambers are consistent with seismic tomography. FEM calculations including free surface effects lead to even larger co-eruptive volume changes, smaller rv and hence larger B. I conclude that the data are consistent with rapid post-eruptive inflation driven by viscoelastic relaxation with a relatively incompressible magma, although other interpretations will be discussed.

Large-scale displacement following the 2016 Kaikōura earthquake

NASA Astrophysics Data System (ADS)

Wang, T.; Peng, D.; Barbot, S.; Wei, S.; Shi, X.

2017-12-01

The 2016 Mw 7.9 Kaikōura earthquake occurred near the southern termination of the Hikurangi subduction system, where a transition from subduction to strike-slip motion dominates the pre-seismic strain accumulation. Dense spatial coverage of the GPS measurements and large amount of Interferometric Synthetic Aperture Radar (InSAR) images provide valuable constraints, from the near field to the far field, to study how the slip is distributed among the subduction interface and the overlying fault system before, during and after the earthquake. We extract time-series deformation from the New Zealand continuous GPS network, and SAR images acquired from Japanese ALOS-2 and European Sentinel-1A/B satellites to image the surface deformation related to the 2016 Kaikōura earthquake. Both GPS and InSAR data, which cover the entire New Zealand region, show that the co-seismic and post-seismic deformations are distributed in an extraordinary large area, as far as to the north tip of the North Island. Based on a coseismic slip model derived from seismic and geodetic observations, we calculate the stress perturbation incurred by the earthquake. We explore a range of possibilities of friction laws and rheology via a linear combination of strain rate in finite volumes and slip velocity on ruptured faults. We obtain the slip distribution that can best explain our geodetic measurements using outlier-insensitive hierarchical Bayesian model, to better understand different mechanisms behind the localized shallow after slip and distributed deformation. Our results indicate that complex interactions between the subduction interface and the overlying fault system play an important role in causing such large-scale deformation during and after the earthquake event.

Subsidence at the Fairport Harbor Water Level Gauge

NASA Astrophysics Data System (ADS)

Conner, D. A.

2014-12-01

SUBSIDENCE AT THE FAIRPORT HARBOR WATER LEVEL GAUGE I will provide information on methods being used to monitor Lake Erie water levels and earth movement at Fairport Harbor, Ohio. Glacial Isostatic Adjustment (GIA) is responsible for vertical movement throughout the Great Lakes region. Fairport Harbor is also experiencing vertical movement due to salt mining, so the nearby water level gauge operated by the National Oceanic and Atmospheric Administration (NOAA) is affected by both GIA and mining. NOAA's National Geodetic Survey (NGS) defines and maintains the National Spatial Reference System (NSRS). The NSRS includes a network of permanently marked points; a consistent, accurate, and up-to-date national shoreline; a network of Continuously Operating Reference Stations (CORS) which supports three-dimensional positioning activities; and a set of accurate models describing dynamic, geophysical processes that affect spatial measurements. The NSRS provides the spatial reference foundation for transportation, mapping, charting and a multitude of scientific and engineering applications. Fundamental elements of geodetic infrastructure include GPS CORS (3-D), water level and tide gauges (height) and a system of vertical bench marks (height). When two or more of these elements converge they may provide an independent determination of position and vertical stability as is the case here at the Fairport Harbor water level gauge. Analysis of GPS, leveling and water level data reveal that this gauge is subsiding at about 2-3 mm/year, independent of the effects of GIA. Analysis of data from the nearby OHLA GPS CORS shows it subsiding at about 4 mm/yr, four times faster than expected due to GIA alone. A long history of salt mine activity in the area is known to geologists but it came as a surprise to other scientists.

Multi-parameter observations in the Ibero-Moghrebian region: the Western Mediterranean seismic network (WM) and ROA GPS geodynamic network

NASA Astrophysics Data System (ADS)

Pazos, Antonio; Martín Davila, José; Buforn, Elisa; Gárate Pasquín, Jorge; Catalán Morollón, Manuel; Hanka, Winfried; Udías, Agustín.; Benzzeghoud, Mourad; Harnafi, Mimoun

2010-05-01

The plate boundary between Eurasia and Africa plates crosses the called "Ibero-Maghrebian" region from the San Vicente Cape (SW Portugal) to Tunisia including the South of Iberia, Alboran Sea, and northern Morocco and Algeria. In this area, the convergence, with a low rate, is accommodated over a wide and diffuse deformation zone, characterized by a significant and widespread moderate seismic activity [Buforn et al., 1995], and the occurrence of large earthquakes is separated by long time intervals. Since more than hundred years ago San Fernando Naval Observatory (ROA), in collaboration with other Institutes, has deployed different geophysical and geodetic equipment in the Southern Spain - North-western Africa area in order to study this broad deformation zone. Currently a Broad Band seismic net (Western Mediterranean, WM net) is deployed, in collaboration with other institutions, around the Gulf of Cádiz and the Alboran sea, with stations in the South of Iberia and in North Africa (at Spanish places and Morocco), together with the seismic stations a permanent geodetic GPS net is co-installed at the same sites. Also, other geophysical instruments have been installed: a Satellite Laser Ranging (SLR) station at San Fernando Observatory Headquarter, a Geomagnetic Observatory in Cádiz bay area and some meteorological stations. These networks have been recently improved with the deployment of a new submarine and on-land geophysical observatory in the Alboran island (ALBO Observatory), where a permanent GPS, a meteorological station were installed on land and a permanent submarine observatory in 50 meters depth was also deploy in last October (with a broad band seismic sensor, a 3 C accelerometer and a DPG). This work shows the present status and the future plans of these networks and some results.

NChina16: A stable geodetic reference frame for geological hazard studies in North China

NASA Astrophysics Data System (ADS)

Wang, Guoquan; Bao, Yan; Gan, Weijun; Geng, Jianghui; Xiao, Gengru; Shen, Jack S.

2018-04-01

We have developed a stable North China Reference Frame 2016 (NChina16) using five years of continuous GPS observations (2011.8-2016.8) from 12 continuously operating reference stations (CORS) fixed to the North China Craton. Applications of NChina16 in landslide and subsidence studies are illustrated in this article. A method for realizing a regional geodetic reference frame is introduced. The primary result of this study is the seven parameters for transforming Cartesian ECEF (Earth-Centered, Earth-Fixed) coordinates X, Y, and Z from the International GNSS Service Reference Frame 2008 (IGS08) to NChina16. The seven parameters include the epoch that is used to align the regional reference frame to IGS08 and the time derivatives of three translations and three rotations. The GIPSY-OASIS (V6.4) software package was used to obtain the precise point positioning (PPP) daily solutions with respect to IGS08. The frame stability of NChina16 is approximately 0.5 mm/year in both horizontal and vertical directions. This study also developed a regional model for correcting seasonal motions superimposed into the vertical component of the GPS-derived displacement time series. Long-term GPS observations (1999-2016) from five CORS in North China were used to develop the seasonal model. According to this study, the PPP daily solutions with respect to NChina16 could achieve 2-3 mm horizontal accuracy and 4-5 mm vertical accuracy after being modified by the regional model. NChina16 will be critical to study geodynamic problems in North China, such as earthquakes, faulting, subsidence, and landslides. The regional reference frame will be periodically updated every few years to mitigate degradation of the frame with time and be synchronized with the update of IGS reference frame.

Probabilistic reconstruction of GPS vertical ground motion and comparison with GIA models

NASA Astrophysics Data System (ADS)

Husson, Laurent; Bodin, Thomas; Choblet, Gael; Kreemer, Corné

2017-04-01

The vertical position time-series of GPS stations have become long enough for many parts of the world to infer modern rates of vertical ground motion. We use the worldwide compilation of GPS trend velocities of the Nevada Geodetic Laboratory. Those rates are inferred by applying the MIDAS algorithm (Blewitt et al., 2016) to time-series obtained from publicly available data from permanent stations. Because MIDAS filters out seasonality and discontinuities, regardless of their causes, it gives robust long-term rates of vertical ground motion (except where there is significant postseismic deformation). As the stations are unevenly distributed, and because data errors are also highly variable, sometimes to an unknown degree, we use a Bayesian inference method to reconstruct 2D maps of vertical ground motion. Our models are based on a Voronoi tessellation and self-adapt to the spatially variable level of information provided by the data. Instead of providing a unique interpolated surface, each point of the reconstructed surface is defined through a probability density function. We apply our method to a series of vast regions covering entire continents. Not surprisingly, the reconstructed surface at a long wavelength is dominated by the GIA. This result can be exploited to evaluate whether forward models of GIA reproduce geodetic rates within the uncertainties derived from our interpolation, not only at high latitudes where postglacial rebound is fast, but also in more temperate latitudes where, for instance, such rates may compete with modern sea level rise. At shorter wavelengths, the reconstructed surface of vertical ground motion features a variety of identifiable patterns, whose geometries and rates can be mapped. Examples are transient dynamic topography over the convecting mantle, actively deforming domains (mountain belts and active margins), volcanic areas, or anthropogenic contributions.

Rupture processes of the 2012 September 5 Mw 7.6 Nicoya, Costa Rica earthquake constrained by improved geodetic and seismological observations

NASA Astrophysics Data System (ADS)

Liu, Chengli; Zheng, Yong; Xiong, Xiong; Wang, Rongjiang; López, Allan; Li, Jun

2015-10-01

On 2012 September 5, the anticipated interplate thrust earthquake ruptured beneath the Nicoya peninsula in northwestern Costa Rica close to the Middle America trench, with a magnitude Mw 7.6. Extensive co-seismic observations were provided by dense near-field strong ground motion, Global Positioning Systems (GPS) networks and teleseismic recordings from global seismic networks. The wealthy data sets available for the 2012 Mw 7.6 Nicoya earthquake provide a unique opportunity to investigate the details of the rupture process of this earthquake. By implementing a non-linear joint inversion with high-rate GPS waveform, more static GPS offsets, strong-motion data and teleseismic body waveform, we obtained a robust and accurate rupture model of the 2012 Mw 7.6 Nicoya earthquake. The earthquake is dominantly a pure thrust component with a maximum slip of 3.5 m, and the main large slip patch is located below the hypocentre, spanning ˜50 km along dip and ˜110 km along strike. The static stress drop is about 3.4 MPa. The total seismic moment of our preferred model is 3.46 × 1020 N m, which gives Mw = 7.6. Due to the fast rupture velocity, most of the seismic moment was released within 70 s. The largest slip patch directly overlaps the interseismic locked region identified by geodetic observations and extends downdip to the intersection with the upper plate Moho. We also find that there is a complementary pattern between the distribution of aftershocks and the co-seismic rupture; most aftershocks locate in the crust of the upper plate and are possibly induced by the stress change caused by the large slip patch.

Development and Demonstration of a Self-Calibrating Pseudolite Array for Task Level Control of a Planetary Rover

NASA Technical Reports Server (NTRS)

Rock, Stephen M.; LeMaster, Edward A.

2001-01-01

Pseudolites can extend the availability of GPS-type positioning systems to a wide range of applications not possible with satellite-only GPS. One such application is Mars exploration, where the centimeter-level accuracy and high repeatability of CDGPS would make it attractive for rover positioning during autonomous exploration, sample collection, and habitat construction if it were available. Pseudolites distributed on the surface would allow multiple rovers and/or astronauts to share a common navigational reference. This would help enable cooperation for complicated science tasks, reducing the need for instructions from Earth and increasing the likelihood of mission success. Conventional GPS Pseudolite arrays require that the devices be pre-calibrated through a Survey of their locations, typically to sub-centimeter accuracy. This is a problematic task for robots on the surface of another planet. By using the GPS signals that the Pseudolites broadcast, however, it is possible to have the array self-survey its own relative locations, creating a SelfCalibrating Pseudolite Array (SCPA). This requires the use of GPS transceivers instead of standard pseudolites. Surveying can be done either at carrier- or code-phase levels. An overview of SCPA capabilities, system requirements, and self-calibration algorithms is presented in another work. The Aerospace Robotics Laboratory at Statif0id has developed a fully operational prototype SCPA. The array is able to determine the range between any two transceivers with either code- or carrier-phase accuracy, and uses this inter-transceiver ranging to determine the at-ray geometry. This paper presents results from field tests conducted at Stanford University demonstrating the accuracy of inter-transceiver ranging and its viability and utility for array localization, and shows how transceiver motion may be utilized to refine the array estimate by accurately determining carrier-phase integers and line biases. It also summarizes the overall system requirements and architecture, and describes the hardware and software used in the prototype system.

Multi-technique comparison of troposphere zenith delays and gradients during CONT08

NASA Astrophysics Data System (ADS)

Teke, Kamil; Böhm, Johannes; Nilsson, Tobias; Schuh, Harald; Steigenberger, Peter; Dach, Rolf; Heinkelmann, Robert; Willis, Pascal; Haas, Rüdiger; García-Espada, Susana; Hobiger, Thomas; Ichikawa, Ryuichi; Shimizu, Shingo

2011-07-01

CONT08 was a 15 days campaign of continuous Very Long Baseline Interferometry (VLBI) sessions during the second half of August 2008 carried out by the International VLBI Service for Geodesy and Astrometry (IVS). In this study, VLBI estimates of troposphere zenith total delays (ZTD) and gradients during CONT08 were compared with those derived from observations with the Global Positioning System (GPS), Doppler Orbitography and Radiopositioning Integrated by Satellite (DORIS), and water vapor radiometers (WVR) co-located with the VLBI radio telescopes. Similar geophysical models were used for the analysis of the space geodetic data, whereas the parameterization for the least-squares adjustment of the space geodetic techniques was optimized for each technique. In addition to space geodetic techniques and WVR, ZTD and gradients from numerical weather models (NWM) were used from the European Centre for Medium-Range Weather Forecasts (ECMWF) (all sites), the Japan Meteorological Agency (JMA) and Cloud Resolving Storm Simulator (CReSS) (Tsukuba), and the High Resolution Limited Area Model (HIRLAM) (European sites). Biases, standard deviations, and correlation coefficients were computed between the troposphere estimates of the various techniques for all eleven CONT08 co-located sites. ZTD from space geodetic techniques generally agree at the sub-centimetre level during CONT08, and—as expected—the best agreement is found for intra-technique comparisons: between the Vienna VLBI Software and the combined IVS solutions as well as between the Center for Orbit Determination (CODE) solution and an IGS PPP time series; both intra-technique comparisons are with standard deviations of about 3-6 mm. The best inter space geodetic technique agreement of ZTD during CONT08 is found between the combined IVS and the IGS solutions with a mean standard deviation of about 6 mm over all sites, whereas the agreement with numerical weather models is between 6 and 20 mm. The standard deviations are generally larger at low latitude sites because of higher humidity, and the latter is also the reason why the standard deviations are larger at northern hemisphere stations during CONT08 in comparison to CONT02 which was observed in October 2002. The assessment of the troposphere gradients from the different techniques is not as clear because of different time intervals, different estimation properties, or different observables. However, the best inter-technique agreement is found between the IVS combined gradients and the GPS solutions with standard deviations between 0.2 and 0.7 mm.

Present-day velocity field and block kinematics of Tibetan Plateau from GPS measurements

NASA Astrophysics Data System (ADS)

Wang, Wei; Qiao, Xuejun; Yang, Shaomin; Wang, Dijin

2017-02-01

In this study, we present a new synthesis of GPS velocities for tectonic deformation within the Tibetan Plateau and its surrounding areas, a combined data set of ˜1854 GPS-derived horizontal velocity vectors. Assuming that crustal deformation is localized along major faults, a block modelling approach is employed to interpret the GPS velocity field. We construct a 30-element block model to describe present-day deformation in western China, with half of them located within the Tibetan Plateau, and the remainder located in its surrounding areas. We model the GPS velocities simultaneously for the effects of block rotations and elastic strain induced by the bounding faults. Our model yields a good fit to the GPS data with a mean residual of 1.08 mm a-1 compared to the mean uncertainty of 1.36 mm a-1 for each velocity component, indicating a good agreement between the predicted and observed velocities. The major strike-slip faults such as the Altyn Tagh, Xianshuihe, Kunlun and Haiyuan faults have relatively uniform slip rates in a range of 5-12 mm a-1 along most of their segments, and the estimated fault slip rates agree well with previous geologic and geodetic results. Blocks having significant residuals are located at the southern and southeastern Tibetan Plateau, suggesting complex tectonic settings and further refinement of accurate definition of block geometry in these regions.

Measuring precise sea level from a buoy using the global positioning system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rocken, C.; Kelecy, T.M.; Born, G.H.

1990-11-01

High-accuracy sea surface positioning is required for sea floor geodesy, satellite altimeter verification, and the study of sea level. An experiment to study the feasibility of using the Global Positioning System (GPS) for accurate sea surface positioning was conducted. A GPS-equipped buoy (floater) was deployed off the Scripps pier at La Jolla, California during December 13-15, 1989. Two reference GPS receivers were placed on land, one within {approximately}100 m of the floater, and the other about 80 km inland at the laser ranging site on Monument Peak. The position of the floater was determined relative to the land-fixed receivers using:more » (a) kinematic GPS processing software developed at the National Geodetic Survey (NGS), and (b) the Jet Propulsion Laboratory's GIPSY (GPS Inferred Positioning SYstem) software. Sea level and ocean wave spectra were calculated from GPPS measurements. These results were compared to measurements made with a NOAA tide gauge and a Paros{trademark} pressure transducer (PPT). GPS sea level for the short 100-m baseline agrees with the PPT sea level at the 1-cm level and has an rms variation of 5 mm over a period of 4 hours. Agreement between results with the two independent GPS analyses is on the order of a few millimeters. Processing of the longer Monument Peak - floater baseline is in progress and will require orbit adjustments and tropospheric modeling to obtain results comparable to the short baseline.« less

Using Internet-Based Automated Software to Process GPS Data at Michigan Tech University

NASA Astrophysics Data System (ADS)

Crook, A.; Diehl, J. F.

2003-12-01

The Michigan Tech University GPS monument was made operational in October of 2002. The monument, which consists of a concrete pillar extending approximately 10 feet below the surface and protrudes 5 feet above ground, is located at the Houghton County Memorial Airport (47.171803° N, 88.498361° W). The primary purpose of the monument is to measure the velocity of the North American Plate at this location. A Trimble 4000ssi geodetic receiver with a Trimble Zephyr antenna is used to collect GPS data. The data are sent to a PC where they are processed using Auto-GIPSY, an internet-based GPS processing utility, which makes it possible to process GPS data, via email, without having knowledge of how the software works. Two Perl scripts were written to facilitate automation and to simplify processing of the GPS data even further. Twelve months of GPS data were processed, using Auto-GIPSY, which produced a velocity of -24 +/- 5 mm/yr and -4 +/- 6 mm/yr for the X and Y components respectively with an azimuth of 261° with respect to the ITRF2000. This calculated result compares well with the NNR-NUVEL1A velocity of -17 mm/yr and -1 mm/yr for the X and Y components respectively with an azimuth of 267° . The results from an alternative online processing service, the Scripps Coordinate Update Tool (SCOUT) that uses GAMIT, will also be presented as a comparative method.

GPS measurements of strain accumulation across the Imperial Valley, California: 1986-1989

NASA Technical Reports Server (NTRS)

Larsen, Shawn; Reilinger, Robert

1989-01-01

The Global Positioning System (GPS) data collected in southern California from 1986 to 1989 indicate considerable strain accumulation across the Imperial Valley. Displacements are computed at 29 stations in and near the valley from 1986 to 1988, and at 11 sites from 1988 to 1989. The earlier measurements indicate 5.9 +/- 1.0 cm/yr right-lateral differential velocity across the valley, although the data are heavily influenced by the 1987 Superstition Hills earthquake sequence. Some measurements, especially the east-trending displacements, are suspects for large errors. The 1988 to 1989 GPS displacements are best modeled by 5.2 +/- 0.9 cm/yr of valley crossing deformation, but rates calculated from conventional geodetic measurements (3.4 to 4.3 cm/yr) fit the data nearly as well. There is evidence from GPS and Very Long Base Interferometry (VLBI) observations that the present slip rate along the southern San Andreas fault is smaller than the long-term geologic estimate, suggesting a lower earthquake potential than is currently assumed. Correspondingly, a higher earthquake potential is indicated for the San Jacinto fault. The Imperial Valley GPS sites form part of a 183 station network in southern California and northern Baja California, which spans a cross-section of the North American-Pacific plate boundary.

GPS Measurements for Detecting Aseismic Creeping in the Ismetpasa Region of North Anatolian Fault Zone, Turkey

NASA Astrophysics Data System (ADS)

Ozener, H.; Dogru, A.; Turgut, B.; Yilmaz, O.; Halicioglu, K.; Sabuncu, A.

2010-12-01

In 1972, a six point-network was established by General Directorate of Mapping in Gerede-Ismetpasa. This region is relatively quiet segment of western NAF which is creeping along steadily. This network was surveyed by terrestrial techniques in 1972 and 1973. The Ismetpasa Network was re-measured in 1982 and in 1992 by the Geodesy Working Group of Istanbul Technical University. Although the same network (with five points) was observed in 2002 and 2007 by Zonguldak Karaelmas University applying GPS technique, with 1-hour site occupation, the characteristics of movement has not been detected implicitly. This type of movement still raises a question about the accumulation of tectonic movements in the region. Geodesy Department of Kandilli Observatory and Earthquake Research Institute (KOERI) of Bogazici University has been re-surveyed the network by campaign-based static GPS surveying (10-hour site occupation) since 2005. The GPS velocities data coming from geodynamic GPS networks of the crustal deformation studies and the analysis of repeated geodetic observations give us significant information about the elastic deformation. Therefore, data gathered in this study is processed using GAMIT/GLOBK software and analyzed together with previously collected data to obtain velocity field and strain accumulation in the study area.

Potential Seasonal Terrestrial Water Storage Monitoring from GPS Vertical Displacements: A Case Study in the Lower Three-Rivers Headwater Region, China.

PubMed

Zhang, Bao; Yao, Yibin; Fok, Hok Sum; Hu, Yufeng; Chen, Qiang

2016-09-19

This study uses the observed vertical displacements of Global Positioning System (GPS) time series obtained from the Crustal Movement Observation Network of China (CMONOC) with careful pre- and post-processing to estimate the seasonal crustal deformation in response to the hydrological loading in lower three-rivers headwater region of southwest China, followed by inferring the annual EWH changes through geodetic inversion methods. The Helmert Variance Component Estimation (HVCE) and the Minimum Mean Square Error (MMSE) criterion were successfully employed. The GPS inferred EWH changes agree well qualitatively with the Gravity Recovery and Climate Experiment (GRACE)-inferred and the Global Land Data Assimilation System (GLDAS)-inferred EWH changes, with a discrepancy of 3.2-3.9 cm and 4.8-5.2 cm, respectively. In the research areas, the EWH changes in the Lancang basin is larger than in the other regions, with a maximum of 21.8-24.7 cm and a minimum of 3.1-6.9 cm.

GPS inferred geocentric reference frame for satellite positioning and navigation

NASA Technical Reports Server (NTRS)

Malla, Rajendra P.; Wu, Sien-Chong

1989-01-01

Accurate geocentric three-dimensional positioning is of great importance for various geodetic and oceanographic applications. While relative positioning accuracy of a few centimeters has become a reality using Very Long Baseline Interferometry (VLBI), the uncertainty in the offset of the adopted coordinate system origin from the geocenter is still believed to be of the order of one meter. Satellite Laser Ranging (SLR) is capable of determining this offset to better than 10 cm, though, because of the limited number of satellites, this requires a long arc of data. The Global Positioning System (GPS) measurements provide a powerful alternative for an accurate determination of this origin offset in relatively short period of time. Two strategies are discussed, the first utilizes the precise relative positions predetermined by VLBI, whereas the second establishes a reference frame by holding only one of the tracking sites longitude fixed. Covariance analysis studies indicate that geocentric positioning to an accuracy of a few centimeters can be achieved with just one day of precise GPS pseudorange and carrier phase data.

Advanced GPS Technologies (AGT)

DTIC Science & Technology

2015-05-01

Distribution A GPS Ill Developmental Optical Clock Deployable Antenna Concept 3 \\.J Science and Technology for GPS •:• Spacecraft • AFRL has funded a...Digital Waveform Generators New antenna concepts Supporting electronics Algorithms and new signal combining methods Satellite bus technologies...GPS Military High Gain Antenna Developing Options for Ground Testing 1) Deployable phased array • Low profile element • High efficiency phase

GPS Velocity Field at the Western Tip of the Aden Ridge ; Implications for Rifting and the Arabia-Somalia-Nubia Triple Junction Dynamics

NASA Astrophysics Data System (ADS)

Doubre, C.; Socquet, A.; Masson, F.; Cressot, C.; Mohamed, K.; Vigny, C.; Ruegg, J.

2010-12-01

Due to the presence of magma and a complex thermal structure, the dynamics of divergent plate boundaries are complicated, with microseismicity (ML<4) contributing very little to the total moment release. For the last 35 years several geodetic campaigns have been conducted at the western tip of the Aden Ridge propagating on land into Afar (Republic of Djibouti). The first segment above water, the Asal Rift, experienced a seismo-volcanic event in 1978, which was the first rifting episode, along with the 1978-1985 Icelandic Krafla event, to be monitored by terrestrial geodetic measurements. These measurements revealed the opening of two 1-2 m-wide dykes in the rift inner floor. Since then, terrestrial and spatial geodetic monitoring shows that the rift kept opening, during the post-rifting period, at a rate largely exceeding the plates’ motions. This significant opening rate is decreasing with time to tend, three decades after the rifting event, to the far-field opening rate. We present here the results of the GPS measurements of a 45 site network covering the Tadjoura-Asal Rift System, previously made every two years from 1995 to 2003, and repeated in 2010. The calculated 1999-2010 horizontal velocity field is very homogeneous with a quasi-constant N045° direction with respect to Somalia and a regular increase from the southern to the northern margin of the Asal Rift clearly controlled by a few normal faults, and reaching a maximum of 12.5 mm/yr. A non-negligible part of the Arabia-Somalia divergent movement (1 to 2 mm/yr) is observed south of this rift, which sheds light on the role of the active normal faults bounding the asymmetrical Gaggadé Basin and therefore brings important constraints on the location of the Red Sea Ridge-Aden Ridge-East African Rift triple junction. Since the last 2003 campaign, the lack of micro-seismicity within the Asal Rift seems to be associated with a ˜2 mm/yr decrease of the opening rate deduced from the GPS time series analysis. These results confirm the importance of non-steady state behavior of the Asal volcano-tectonic rift segment, and the role of geothermal/volcanic activity on the occurrence of transients, as suggested by InSAR results.

Predicting present-day rates of glacial isostatic adjustment using a smoothed GPS velocity field for the reconciliation of NAD83 reference frames in Canada

NASA Astrophysics Data System (ADS)

Craymer, M. R.; Henton, J. A.; Piraszewski, M.

2008-12-01

Glacial isostatic adjustment following the last glacial period is the dominant source of crustal deformation in Canada east of the Rocky Mountains. The present-day vertical component of motion associated with this process may exceed 1 cm/y and is being directly measured with the Global Positioning System (GPS). A consequence of this steady deformation is that high accuracy coordinates at one epoch may not be compatible with those at another epoch. For example, modern precise point positioning (PPP) methods provide coordinates at the epoch of observation while NAD83, the officially adopted reference frame in Canada and the U.S., is expressed at some past reference epoch. The PPP positions are therefore incompatible with coordinates in such a realization of the reference frame and need to be propagated back to the frame's reference epoch. Moreover, the realizations of NAD83 adopted by the provincial geodetic agencies in Canada are referenced to different coordinate epochs; either 1997.0 or 2002.0. Proper comparison of coordinates between provinces therefore requires propagating them from one reference epoch to another. In an effort to reconcile PPP results and different realizations of NAD83, we empirically represent crustal deformation throughout Canada using a velocity field based solely on high accuracy continuous and episodic GPS observations. The continuous observations from 2001 to 2007 were obtained from nearly 100 permanent GPS stations, predominately operated by Natural Resources Canada (NRCan) and provincial geodetic agencies. Many of these sites are part of the International GNSS Service (IGS) global network. Episodic observations from 1994 to 2006 were obtained from repeated occupations of the Canadian Base Network (CBN), which consists of approximately 160 stable pillar-type monuments across the entire country. The CBN enables a much denser spatial sampling of crustal motions although coverage in the far north is still rather sparse. NRCan solutions of the continuous GPS data were combined with those from other agencies as part of the North American Reference Frame (NAREF) effort to improve the reliability of the results. This NAREF solution has then been combined with our CBN results to obtain a denser velocity sampling for fitting different types of surfaces in a first attempt to determine a continuous GPS velocity field for the entire country. Expressing this velocity field as a grid enables users to interpolate to any location in Canada, allowing for the propagation of coordinates to any desired reference epoch. We examine the accuracy and limitations of this GPS velocity field by comparing it to other published GPS velocity solutions (which are all based on less data) as well as to GIA models, including versions of ICE-3G, ICE-5G and the recent Stable North America Reference Frame (SNARF) model. Of course, the accuracy of the GPS velocity field depends directly on the density of the GPS coverage. Consequently, the GPS velocity field is unable to fully represent the actual GIA motion in the far north and tends to smooth out the signal due to the spatially sparse coverage. On the other hand, the model performs quite well in the southern parts of the country where there is a much greater spatial density of GPS measurements.

Time dependent deformation of Kilauea Volcano, Hawaii

NASA Astrophysics Data System (ADS)

Montgomery-Brown, Emily Kvietka Desmarais

In 1997 the continuous Global Positioning System (GPS) network was completed on Kilauea, providing the first network of daily position measurements during eruptions and earthquakes on Kilauea. Kilauea has been studied for many decades with continuous seismic and tilt instruments. Other geodetic data (e.g., campaign GPS, leveling, electronic distance measurements) are also available although they contain only sparse data. Data analysis methods used here include inverting multiple data sets for optimal source parameters and the spatio-temporal distribution of magma volume and fault slip, and combining GPS and seismic observations to understand flank tectonics. The field area for this study, Kilauea Volcano, was chosen because of its frequent activity and potential hazards. The 1997 East Rift Zone eruption (Episode 54) was the first major event to occur after the completion of the continuous GPS network. The event lasted 2 days, but transient deformation continued for six months. This long-duration transient allowed the first spatio-temporal study of transient dike deformation on Kilauea from daily GPS positions. Slow-slip events were discovered on Kilauea during which the southern flank of the volcano would accelerate seaward for approximately 2 days. The discovery was made possible because of the continuously operating GPS network. These slip events were also observed to correlate with small swarms of microearthquakes found to follow temporal pattern consistent with them being co- and aftershocks of the slow-slip event (Segall, 2006). Half-space models of geodetic data favor a shallow fault plane (˜ 5 km), which is much too shallow to have increased the Coulomb stress at the depths of the co- and aftershocks. However, optimizations for the slow-slip source parameters including a layered elastic structure and a topographic correction favor deeper models within the range of the co- and aftershocks. Additionally, the spatial distribution of seaward fault slip, fixed to a decollement structure 8 km under the south flank, and the locations of the microearthquakes suggest that both occur on the same structure. In 2007, Episode 56 of the Pu'u 'O'o-Kupianaha eruption occurred. This episode was exciting both because it was the largest intrusion in the last decade, and because it occurred concurrently with a flank slow-slip event. The intrusion started on Father's day (June 17th), 2007 with increased seismicity and abrupt tilts at the summit and rift zones. Quasi-static models of the total deformation determined from GPS, tilt, and InSAR indicate that the intrusion occurred on two en echelon dike segments in the upper East Rift Zone along with deformation consistent with slow-slip in the same areas of previous events. The ˜ 2 m maximum opening occurred on the eastern segment near Makaopui crater. Unlike previous intrusions in 1997, 1999, and 2000, the dike model was not sufficient to explain deformation on the western flank. Additionally, a coastal tiltmeter installed in anticipation of a slow-slip event recorded tilts consistent with those observed during the 2005 slow-slip event. These observations led to the conclusion that a concurrent slow-slip event occurred. Geodetic models indicate a similar amount of decollement slip occurred as in previous slow-slip events. Sub-daily GPS positions were used to study the spatio-temporal distribution of the dike intrusion. The time-dependent intrusion model shows that the intrusion began on the western en echelon segment before jumping to the eastern segment, which accumulated the majority of the 2 m of opening. Sub-daily GPS positions limit the number of stations available since there are very few continuous stations north of the East Rift Zone, where coverage is critical for separating the intrusion from the slow-slip. However, an ENVISAT interferogram at 08:22 on June 18, 2007 provides additional spatial coverage of deformation up to that point. Combining this image with the GPS and tilt data up to that point, we perform a quasi-static inversion for the intrusion source. The residual deformation indicates that slow-slip had not significantly progressed by the ENVISAT image. The slow-slip event occurred therefore at least 20 hours after the initiation of the dike intrusion. (Abstract shortened by UMI.)

Study of Ground Subsidence in North West Houston using GPS, LiDAR and InSAR techniques

NASA Astrophysics Data System (ADS)

Karacay, A.; Khan, S. D.

2012-12-01

Land subsidence can be caused by natural or human activities, such as carbonate dissolution, extraction of material from mines, soil compaction and fluid withdrawal. This phenomenon affects many cities around the world, such as Nagoya-Japan, Venice-Italy, San Joaquin Valley and Long Beach in California. Recent work by Engelkemeir et al, (2010), suggested that subsidence occurred as high as 5.6 cm/year in northwest Houston. The processes that may contribute to land subsidence in the Houston-Galveston area includes faulting, soil compaction, salt tectonic, water pumping and hydrocarbon extraction. This study aims to assess the possible role of water pumping on subsidence. Northwest Houston has two aquifer systems, the Evangeline and Chicot aquifers that dip in the southeast direction. The effect of water pumping on subsidence from these two aquifers was monitored using InSAR, GPS and LiDAR data. The data from eleven GPS stations were processed using Online Positioning User Service (OPUS) of National Geodetic Survey (NGS). Three of these GPS stations are Continuously Operating Reference Stations (CORS) and eight are Port-A-Measure (PAM) sites. All the GPS data were obtained from Harris-Galveston Subsidence District (HGSD). CORS sites were used as reference stations for processing GPS data from the PAM stations. GPS data show that subsidence rate in northwest Houston decreased to approximately 2 cm/year. In addition, the surface deformation is also estimated using Light Detection and Ranging (LiDAR) technique. For this purpose, raw LiDAR (LAS-Long ASCII Standart) files of 2001 and 2008 were processed. The subsidence rate near the Hockley Fault was calculated by applying zonal statistics method on LiDAR data which shows about 10 cm of subsidence in nine years. This result is supported by processed GPS data from PAM site 48 that show subsidence rate of 1.3 cm/yr. For the InSAR (Interferometric Synthetic Aperture Radar) technique, an image pair of PALSAR (The Phased Array type L-band Synthetic Aperture Radar) for 2008 was processed using Sarscape ENVI. The result demonstrates both uplift (approximately 5 mm near the Tomball salt dome) and subsidence (approximately 5.3 mm on the west part of Tomball region). In order to improve results, other image pairs from PALSAR, ERS1/2 and ENVISAT are being processed to monitor surface changes before and after 2000. Changes of groundwater level in the study area were observed, in order to distinguish the amount of land subsidence caused by groundwater withdrawal. The groundwater historical observation data were taken from The USGS National Water Information System (NWIS). The results of the groundwater level between 1990 and 2011 show approximately 0.5 m per year of water decline in the study area. Results of these complementary techniques will help in assessing the possible role of the water pumping from the subsurface on the subsidence in the area.

Performance assessment of multi-GNSS real-time PPP over Iran

NASA Astrophysics Data System (ADS)

Abdi, Naser; Ardalan, Alireza A.; Karimi, Roohollah; Rezvani, Mohammad-Hadi

2017-06-01

With the advent of multi-GNSS constellations and thanks to providing the real-time precise products by IGS, multi-GNSS Real-Time PPP has been of special interest to the geodetic community. These products stream in the form of RTCM-SSR through NTRIP broadcaster. In this contribution, we aim at assessing the convergence time and positioning accuracy of Real-Time PPP over Iran by means of GPS, GPS + GLONASS, GPS + BeiDou, and GPS + GLONASS + BeiDou configurations. To this end, RINEX observations of six GNSS stations, within Iranian Permanent GNSS Network (IPGN), over consecutive sixteen days were processed via BKG NTRIP Client (BNC, v 2.12). In the processing steps, the IGS-MGEX broadcast ephemerides (BRDM, provided by TUM/DLR) and the pre-saved CLK93 broadcast corrections stream (provided by CNES) have been used as the satellites known information. The numerical results were compared against the station coordinates obtained from the double-difference solutions by Bernese GPS Software v 5.0. Accordingly, we have found that GPS + BeiDou combination can reduce the convergence time by 27%, 16% and 10% and improve the positioning accuracy by 22%, 18% and 2%, in the north, east and up components, respectively, as compared with the GPS PPP. Additionally, in comparison to the GPS + GLONASS results, GPS + GLONASS + BeiDou combination speeds up the convergence time by 9%, 8% and 9% and enhance the positioning accuracy by 8%, 5% and 6%, in the north, east and up components, respectively. Overall, thanks to the availability of the current BeiDou constellation observations, the considerable decrease in the convergence time on one hand, and the improvement in the positioning accuracy on the other, can verify the efficiency of utilizing multi-GNSS PPP for real-time applications over Iran.

3D displacements maps of the L'Aquila earthquake by applying SISTEM method to GPS and ENVISAT and ALOS DInSAR data

NASA Astrophysics Data System (ADS)

Guglielmino, Francesco; Anzidei, Marco; Briole, Pierre; de Michele, Marcello; Elias, Panagiotis; Nunnari, Giuseppe; Puglisi, Giuseppe; Spata, Alessandro

2010-05-01

We present an application of the novel SISTEM (Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements) approach [Guglielmino et al., 2009] to obtain a 3D estimation of the ground deformation pattern produced by the April 6, 2009, Mw 6.3 L'Aquila earthquake, the most destructive in the Abruzzo region since the huge 1703 earthquake [Boschi et al., 2000; Chiarabba et al., 2005]. The focal mechanism of the main shock is of normal faulting with NE-SW oriented T-axis [INGV, 2009]. Most of the aftershocks, located by the INGV seismic network, are in the depth range 5÷15 km, depicting a SW dipping fault plane [INGV, 2009]. Field observations [EMERGEO working group, 2009] have identified surface ground cracks with centimeter to decimeters throws over a wide belt running along the Paganica Fault. A closely spaced GPS (Global Positioning System) network was set up in this sector of the Apennines after 1999 [Anzidei et al., 2005] and more than 10 Continuous GPS (CGPS) stations have been operating in this region over the last years. On March 30 2008, INGV installed five GPS receivers on selected benchmarks of the Central Apennine Geodetic Network (CaGeoNet) bordering the L'Aquila basin in order to detect the eventual ground movements during the seismic sequence. These stations were crucial to resolve the near-field co-seismic deformation pattern properly, allowing direct observation of the details of co-seismic displacement related to the main shock. Thanks to the ESA Earth Watching project, which made Envisat data quickly available after their acquisition, we performed a DInSAR (Differential Interferometric Synthetic Aperture Radar) analysis of ascending and descending images sampling the date of the earthquake. In particular, we analyze the descending pair for the interval 27/04/2008 - 12/04/2009 (tbline = 350 days; Bperp = 44m) and the ascending pair for the interval 11/03/2009 - 15/04/2009 (tbline = 35 days; Bperp = 227m). We also analyzed ALOS PALSAR interferograms produced with images acquired along two different ascending tracks and relevant to the 3/7/2008 - 21/5/2009 time interval (track 638; tbline = 322 days; Bperp = 665 m ) and 2/3/2007 - 22/4/2009 time interval (track 639; tbline = 782 days; Bperp = 466 m ). In order to derive 3D surface motion maps, we apply the SISTEM method to the available geodetic dataset (both GPS and DInSAR). The SISTEM method performs an integration of GPS and DInSAR data for computing displacements on each point of the studied area. The SISTEM is based on elastic theory, and provides the complete 3D strain and the rigid body rotation tensors in the same solution. To achieve higher accuracy and get better the constraint of the 3D components of the displacements, we improved the standard formulation of SISTEM approach, based on a single DInSAR data, in order to take into account both ascending and descending interferograms and the DInSAR data acquired by different sensors(ALOS and ENVISAT). The SISTEM integration results show a complex kinematics, where the main movements (max westward movement of 165 mm associated with a max lowering of 260 mm) are recorded in the area between the surface evidence of the Paganica fault and Monticchio-fossa fault. These results, which provide both accurate and fine spatial characterization of ground deformation, are hence promising for future studies aimed at improving the knowledge of the kinematic of the Paganica fault and identification of additional faults responsible of the seismic sequence and that have contributed to the observed ground deformation. References. Anzidei, M., P. Baldi, A. Pesci, A. Esposito, A. Galvani, F. Loddo, P. Cristofoletti, A. Massucci, and S. Del Mese (2005), Geodetic deformation across the Central Apennines from GPS data in the time span 1999-2003, Ann. Geophys., 48(2), 259-271. Boschi, E., E. Guidoboni, G. Ferrrari, D. Mariotti, G. Valensise, and P. Gasperini (2000), Catalogue of strong Italian earthquakes from 461 B.C. to 1997, Ann. Geofis., 43, 609- 868. Chiarabba, C., L. Jovane, and R. Di Stefano (2005), A new view of Italian seismicity using 20 years of instrumental recordings, Tectonophysics, 395, 251-268, doi:10.1016/j.tecto.2004.09.013. EMERGEO Working Group (2009), Field geological survey in the epicentral area of the Abruzzi (central Italy) seismic sequence of April 6th, 2009, in Quaderni di Geofisica, vol. 70, Ist. Naz. Di Geofis. e Vulcanol., Rome. Guglielmino F., Nunnari G., Puglisi G., Spata A. (2009), Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements (SISTEM) to obtain threedimensional displacements maps. Submitted to IEEE Transactions on Geoscience and Remote Sensing. Istituto Nazionale di Geofisica e Vulcanologia (INGV) (2009), The L'Aquila seismic sequence— April 2009, Ist. Naz. di Geofis. e Vulcanol., Rome. (Available at http://portale.ingv.it/).

Overview of new GNSS tropospheric products for GNSS-meteorology and their assessment at Geodetic Observatory Pecny (CZ)

NASA Astrophysics Data System (ADS)

Dousa, J.; Vaclavovic, P.; Gyori, G.

2012-12-01

Geodetic Observatory Pecný (GOP) has a long-term experience in the estimation of precise tropospheric parameters from GNSS permanent stations, in particular under the limited timelines of near real time. More than a decade, the GOP zenith total delays (ZTD) contributed to various projects in Europe (COST-716, TOUGH, E-GVAP, E-GVAP II) and the operational ZTD hourly updated product flows via the meteorological observation exchange network - GTS - to the end users worldwide. Currently, the GOP regional ZTD product is operationally assimilated in Météo France and UK MetOffice at least and further exploited in various ways at many other meteorological institutions. New developments at GOP over last three years consist of a) implementation and assessment of the global hourly ZTD product of about 170 stations, b) implementation of routine multi-GNSS (GPS+GLONASS) ZTD European product, and c) implementation of ultra-fast/real-time ZTD product. The GOP global ZTD product has been implemented on request of the meteorological institutions running global numerical weather forecasting models. The global ZTD product was seriously evaluated over ten months (Oct 2009 - Aug 2011) when compared to reprocessed EUREF and IGS ZTDs, radiosondes and ZTDs derived from UK MetOffice's global numerical weather model. After the evaluation (and on special request of UK MetOffice) the product has been switched from testing to operational status within the framework of the EUMETNET EIG GPS Water Vapour Programme (E-GVAP) and officially disseminated via the GTS network. The GOP multi-GNSS ZTD solution has been tested since 2009 shortly after developing GOP ultra-rapid GPS+GLONASS orbits for the International GNSS Service (IGS). A specific bias of mean value 1.5 mm was identified between GPS- and GLONASS-only ZTD at that time, and relation to the IGS05 antenna phase centre offset and variation models (PCO+PCV) identified. Consequently, the implementation of a routine operation has been done after the GPS week 1632 together with adopting IGS08 PCO+PCVs, which eliminated the bias and demonstrated an overall general better consistence between GPS- and GLONASS-only ZTD estimates. The multi-GNSS ZTD product runs in parallel to the GPS-only and is going to replace the current official GPS-only product after more than a year assessment. This multi-GNSS product has assesses a satisfactory quality and robustness of unofficial IGS ultra-rapid GPS+GLONASS orbits necessary for multi-GNSS solution. The GOP ultra-fast and real-time ZTD estimation is being developed with in-house software application using own G-Nut library and Precise Point Positioning technique (in contrast to all other GOP ZTD products based on Bernese GPS software and based on double-difference observations). The IGS Real-time Pilot Project orbit and clock corrections are seriously exploited in these ultra-fast and real-time tropospheric products aimed for nowcasting and severe weather monitoring. Our implementation assesses an optimal balance between timelines and product quality required by these applications.

On the Possibility of Interseismic Creep of the Cascadia Megathrust

NASA Astrophysics Data System (ADS)

Wang, Y.; Wang, K.; He, J.

2012-12-01

Without any instrumental records of large megathrust earthquakes, our knowledge of the seismic potential of the Cascadia subduction zone depends critically on our understanding of the present state of interseismic fault locking. The traditional view of a fully and uniformly locked Cascadia megathrust, consistent with the extremely low modern interplate seismicity, is now challenged for two reasons. First, recent quantitative analyses of high-quality microfossil data indicate that fault slip in the great Cascadia earthquake of 1700 was heterogeneous, with high-slip areas separated by low-slip areas. This leads to the question whether the low-slip areas should exhibit interseismic creeping after the earthquake and even at present. Second, the most recent inversion of GPS measurements to infer simultaneously megathrust locking, permanent upper plate deformation, and block motion features large creeping (i.e., partial locking) segments along the margin. For example, in northern Cascadia offshore of Vancouver Island, the creep rate is reported to be about 40% of the plate convergence rate of ~50 mm/yr used in this inversion. Here we re-examine the locking state of the northern Cascadia megathrust by exploring the following issues. (1) The geodetically observed contemporary margin-normal shortening has a relatively low velocity gradient but extends quite far inland. In an elastic model, the near-field low strain rate can be explained by partial locking, and the broad pattern is explained by permanent shortening, e.g., across the Canadian Coast Mountains. We investigate whether a viscoelastic model can explain the geodetic strains with a fully locked megathrust without permanent upper plate shortening. (2) The new global plate motion model MORVEL predicts a lower convergence rate of only ~40 mm/yr at northern Cascadia. We investigate its implications to the interpretation of the geodetic observations. (3) Globally, afterslip following a great earthquake is generally observed to have a short duration. We investigate whether the contemporary Cascadia deformation field could still be under the influence of the 1700 event, especially that of the post-seismic behaviour of its low-slip areas. (4) We investigate to what extent land-based GPS observations can resolve partial locking vs. full locking of the offshore seismogenic zone. We develop a 3-D viscoelastic model with a fully locked plate interface but with the locking width varying along strike and test whether this model can explain GPS observations as well as does the partially locked elastic model. We also develop an alternative model with multiple slow slip events of spatiotemporally varying source regions, in order to investigate whether their integrated effect could be identified as partial locking by land-based GPS. Our work at Cascadia may also help understand the interseismic creep reported for other subduction zones.

Real-Time In-Situ Measurements for Earthquake Early Warning and Space-Borne Deformation Measurement Mission Support

NASA Astrophysics Data System (ADS)

Kedar, S.; Bock, Y.; Webb, F.; Clayton, R. W.; Owen, S. E.; Moore, A. W.; Yu, E.; Dong, D.; Fang, P.; Jamason, P.; Squibb, M. B.; Crowell, B. W.

2010-12-01

In situ geodetic networks for observing crustal motion have proliferated over the last two decades and are now recognized as indispensable tools in geophysical research, along side more traditional seismic networks. The 2007 National Research Council’s Decadal Survey recognizes that space-borne and in situ observations, such as Interferometric Synthetic Aperture Radar (InSAR) and ground-based continuous GPS (CGPS) are complementary in forecasting, in assessing, and in mitigating natural hazards. However, the information content and timeliness of in situ geodetic observations have not been fully exploited, particularly at higher frequencies than traditional daily CGPS position time series. Nor have scientists taken full advantage of the complementary natures of geodetic and seismic data, as well as those of space-based and in situ observations. To address these deficits we are developing real-time CGPS data products for earthquake early warning and for space-borne deformation measurement mission support. Our primary mission objective is in situ verification and validation for DESDynI, but our work is also applicable to other international missions (Sentinel 1a/1b, SAOCOM, ALOS 2). Our project is developing new capabilities to continuously observe and mitigate earthquake-related hazards (direct seismic damage, tsunamis, landslides, volcanoes) in near real-time with high spatial-temporal resolution, to improve the planning and accuracy of space-borne observations. We also are using GPS estimates of tropospheric zenith delay combined with water vapor data from weather models to generate tropospheric calibration maps for mitigating the largest source of error, atmospheric artifacts, in InSAR interferograms. These functions will be fully integrated into a Geophysical Resource Web Services and interactive GPS Explorer data portal environment being developed as part of an ongoing MEaSUREs project and NASA’s contribution to the EarthScope project. GPS Explorer, originally designed for web-based dissemination of long-term Solid Earth Science Data Records (ESDR’s) such as deformation time series, tectonic velocity vectors, and strain maps, provides the framework for seamless inclusion of the high rate data products. Detection and preliminary modeling of interesting signals by dense real-time high-rate ground networks will allow mission planners and decision makers to fully exploit the less-frequent but higher resolution InSAR observations. Fusion of in situ elements into an advanced observation system will significantly improve the scientific value of extensive surface displacement data, provide scientists with improved access to modern software tools to manipulate and model these data, increase the data’s accuracy and timeliness at higher frequencies than available from space-based observations, and increase the accuracy of space-based observations through calibration of atmospheric and other systematic errors.

The Promise and Challenges of High Rate GNSS for Environmental Monitoring and Response

NASA Astrophysics Data System (ADS)

LaBrecque, John

2017-04-01

The decadal vision Global Geodetic Observing System recognizes the potential of high rate real time GNSS for environmental monitoring. The GGOS initiated a program to advance GNSS real time high rate measurements to augment seismic and other sensor systems for earthquake and tsunami early warning. High rate multi-GNSS networks can provide ionospheric tomography for the detection and tracking of land, ocean and atmospheric gravity waves that can provide coastal warning of tsunamis induced by earthquakes, volcanic eruptions, severe weather and other catastrophic events. NASA has collaborated on a microsatellite constellation of GPS receivers to measure ocean surface roughness to improve severe storm tracking and a equatorial system of GPS occultation receivers to measure ionospheric and atmospheric dynamics. Systems such as these will be significantly enhanced by the availability of a four fold increase in GNSS satellite systems with new and enhanced signal structures and by the densification of regional multi-GNSS networks. These new GNSS capabilities will rely upon improved and cost effective communications infrastructure for a network of coordinated real time analysis centers with input to national warning systems. Most important, the implementation of these new real time GNSS capabilities will rely upon the broad international support for the sharing of real time GNSS much as is done in weather and seismic observing systems and as supported by the Committee of Experts on UN Global Geodetic Information Management (UNGGIM).

Crustal deformation and source models of the Yellowstone volcanicfield from geodetic data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vasco, D.W.; Puskas, C.M.; Smith, R.B.

2006-07-05

Geodetic observations, comprised of InterferometricSynthetic Aperture Radar (InSAR), Global Positioning System (GPS). andleveling measurements, are used to infer volume change in the subsurfaceassociated with the Yellowstone volcanic system. We find that existingfaults play a significant role in controlling subsurface volume increasesand decreases due to fluid migration within the volcanic system. Forexample, subsidence from 1992 to 1995 appears to be associated withvolume changes below the Elephant Back fault zone and a north-southtrending fault which cuts across the caldera. Furthermore, we are able toimage an episode of magma intrusion near the northern edge of the calderawhich parallels and is adjacent to themore » north trending volume decrease.The primary intrusion occurred between 1996 and 2000, though theintrusion appears to have continnued, shallowed, and changed shapebetween 2000 and 2001. There is evidence that the intrusive activityaffected extensional fauts to the north of the caldera.« less

A water-vapor radiometer error model. [for ionosphere in geodetic microwave techniques

NASA Technical Reports Server (NTRS)

Beckman, B.

1985-01-01

The water-vapor radiometer (WVR) is used to calibrate unpredictable delays in the wet component of the troposphere in geodetic microwave techniques such as very-long-baseline interferometry (VLBI) and Global Positioning System (GPS) tracking. Based on experience with Jet Propulsion Laboratory (JPL) instruments, the current level of accuracy in wet-troposphere calibration limits the accuracy of local vertical measurements to 5-10 cm. The goal for the near future is 1-3 cm. Although the WVR is currently the best calibration method, many instruments are prone to systematic error. In this paper, a treatment of WVR data is proposed and evaluated. This treatment reduces the effect of WVR systematic errors by estimating parameters that specify an assumed functional form for the error. The assumed form of the treatment is evaluated by comparing the results of two similar WVR's operating near each other. Finally, the observability of the error parameters is estimated by covariance analysis.

Comparaisons d'étalons primaires de fréquence par GPS.

NASA Astrophysics Data System (ADS)

Uhrich, P. J.-M.

The new primary frequency standard of the BNM-LPTF, LPTF FO1, exhibits a frequency accuracy estimated at 3×10-15. For the comparison with other primary frequency standards, it then requires a method that remains at a stability level better than 10-15 between ten hours, during which it remains generally in continuous operation, and a couple of days, where the local oscillator towards which LPTF FO1 is estimated keeps its frequency at a level of 2×10-15. The well known GPS common-view method does not fit any more when using a single channel receiver: the clock comparison measurements exhibit a frequency stability at a few parts in 10-14 over one day, depending on the distance between the clock, and the intrinsic best stability level limited by the GPS signal currently used can be calculated at 7.7×10-15. But is can be shown that a 4 channel receiver, performing as many regular common-views as possible over each day, would allow to reach 10-15 on actual measurements. That should also be the case for an other option: the use of the carrier phase of the GPS signal, associated with global geodetic computing.

Highlights of Recent Developments in the International GPS Service and Perspectives for Future Directions

NASA Technical Reports Server (NTRS)

Neilan, R.; Reigber, C.; Springer, T.; Beutler, G.; Kouba, J.

1999-01-01

In December 1998, the IGS Governing Board officially changed the name of this IAG service from 'International GPS Service for Geodynamics to simply the 'International GPS Service'. This change of name reflects the fact that today the IGS supports numerous scientific projects outside the traditional geodetic and geodynamic disciplines. A number of IGS projects and working groups have been established, each concentrating on a particular science application, such as the ionosphere, atmosphere, reference frame, precise time transfer, etc. These activities are enabled and simulated by the IGS and directly contribute to the continuing development of the service. The IGS is currently poised to respond to evolving user requirements that focus on timeliness and reliability of data and products, particularly in support of a slate of Low Earth Orbiter missions over the next decade. Perspectives on the future of the IGS will be developed based on current directions as well as anticipated external influences, such as GPS satellite modernization, GLONASS, availability of global communications, and plans for the European GALILEO (Global Navigation Satellite System - GNSS). We will address development of user friendly interfaces and IGS product tutorials.

Analysis of Vlbi, Slr and GPS Site Position Time Series

NASA Astrophysics Data System (ADS)

Angermann, D.; Krügel, M.; Meisel, B.; Müller, H.; Tesmer, V.

Conventionally the IERS terrestrial reference frame (ITRF) is realized by the adoption of a set of epoch coordinates and linear velocities for a set of global tracking stations. Due to the remarkable progress of the space geodetic observation techniques (e.g. VLBI, SLR, GPS) the accuracy and consistency of the ITRF increased continuously. The accuracy achieved today is mainly limited by technique-related systematic errors, which are often poorly characterized or quantified. Therefore it is essential to analyze the individual techniques' solutions with respect to systematic differences, models, parameters, datum definition, etc. Main subject of this presentation is the analysis of GPS, SLR and VLBI time series of site positions. The investigations are based on SLR and VLBI solutions computed at DGFI with the software systems DOGS (SLR) and OCCAM (VLBI). The GPS time series are based on weekly IGS station coordinates solutions. We analyze the time series with respect to the issues mentioned above. In particular we characterize the noise in the time series, identify periodic signals, and investigate non-linear effects that complicate the assignment of linear velocities for global tracking sites. One important aspect is the comparison of results obtained by different techniques at colocation sites.

Assessing the Contribution of Superconducting Gravimetry and GPS to Lunar Laser Ranging at Apache Point Observatory, New Mexico

NASA Astrophysics Data System (ADS)

Crossley, D. J.; Murphy, T.; Borsa, A. A.; Boy, J. P.

2016-12-01

Lunar laser ranging (LLR) is one of the main techniques used to test fundamental aspects of theories of the general relativity by monitoring the Earth-Moon distance to high accuracy. A current limitation of the APO processing is knowledge of the deformation of the telescope orientation at the sub-cm level in response to local loading and attraction effects. To this end in 2009 a superconducting gravimeter was installed at the Apache Point Observatory (APO), close to one of the Plate Boundary Observatory (PBO) GPS sites at the Sunspot solar observatory. APO is also visited regularly for AG measurements by the NGA. We present a comprehensive analysis of the 7 years of gravity data from APO, and the height variations from GPS, to give accurate estimates of the local elastic parameters and vertical variations common to both sites. By including the full spectrum (e.g. from tides, polar motion, and hydrology) of known loading and surface mass variability effects on gravity and GPS, we assess the vertical control that such geodetic techniques can bring to LLR measurements, and by extension, to other astronomical installations.

A new voxel-based model for the determination of atmospheric weighted mean temperature in GPS atmospheric sounding

NASA Astrophysics Data System (ADS)

He, Changyong; Wu, Suqin; Wang, Xiaoming; Hu, Andong; Wang, Qianxin; Zhang, Kefei

2017-06-01

The Global Positioning System (GPS) is a powerful atmospheric observing system for determining precipitable water vapour (PWV). In the detection of PWV using GPS, the atmospheric weighted mean temperature (Tm) is a crucial parameter for the conversion of zenith tropospheric delay (ZTD) to PWV since the quality of PWV is affected by the accuracy of Tm. In this study, an improved voxel-based Tm model, named GWMT-D, was developed using global reanalysis data over a 4-year period from 2010 to 2013 provided by the United States National Centers for Environmental Prediction (NCEP). The performance of GWMT-D was assessed against three existing empirical Tm models - GTm-III, GWMT-IV, and GTmN - using different data sources in 2014 - the NCEP reanalysis data, surface Tm data provided by Global Geodetic Observing System and radiosonde measurements. The results show that the new GWMT-D model outperforms all the other three models with a root-mean-square error of less than 5.0 K at different altitudes over the globe. The new GWMT-D model can provide a practical alternative Tm determination method in real-time GPS-PWV remote sensing systems.

Geodetic component of the monitoring of tectonic and hydrogeological activities in Kopacki Rit Nature Park

NASA Astrophysics Data System (ADS)

Dapo, Almin; Pribicevic, Bosko

2013-04-01

Based on the European and global experience, the amplitude change in the structural arrangement caused by recent tectonic movements, can be most accurately determined by repeated precise GPS measurements on specially stabilized geodetic and geodynamic points. Because of these reasons, the GPS method to determine the movements on specially stabilized points in the Nature park Kopacki rit is also applied in this project. Kopacki rit Nature Park is the biggest preserved natural flooded area on the Danube. It is spread over 23 000 hectares between the rivers Danube and Drava and is one of the biggest fluvial wetland valleys in Europe. In 1993 it was listed as one of internationally valuable wetlands according to the Ramsar Convention. By now in Kopacki rit there have been sights of about 295 bird species, more than 400 species of invertebrates and 44 types of fish. Many of them are globally endangered species like, white tailed eagle, black stork and prairie hawk. It's not rare to come across some deer herds, wild boars or others. Today's geological and geomorphological relations in the Nature park Kopacki rit are largely the result of climate, sedimentary, tectonic and anthropogenic activity in the last 10,000 years. Unfortunately the phenomenon of the Kopacki rit Nature park is in danger to be over in the near future due to those and of course man made activities on the Danube river. It is trough scientific investigations of tectonic and hydrogeological activities that scientist from University of Zagreb are trying to contribute to wider knowledge and possible solutions to this problem. In the year 2009 the first GPS campaign was conducted, and the first set of coordinates of stabilized points was determined which can be considered zero-series measurements. In 2010 a second GPS campaign was conducted and the first set of movements on the Geodynamic Network of Kopacki Rit Nature Park was determined. Processing GPS measurements from 2009 and 2010 was carried out in a scientific software with multipoint solutions GAMIT / GLOBK, using Kalman filter to determine the velocity from discrete campaigns. This paper presents the performed measurements, processing and analysis of the results, which indicate that there are geodynamicaly significant developments.

Transients in Pacific/North American Plate Boundary Deformation: Synthesis and Modeling of GPS and Borehole Strain Observations

NASA Technical Reports Server (NTRS)

Solomon, Sean C.; Frey, H. V. (Technical Monitor)

2002-01-01

This is the Final Technical Report on research conducted between 1 June 1997 and 14 September 2001 entitled "Transients in Pacific/North American plate boundary deformation: Synthesis and modeling of GPS and borehole strain observations." As the project title implies, our effort involved a geodetic study of strain transients, i.e., temporal variations in deformation rates, that occur within plate boundary zones and their relationship to earthquakes and plate motions. Important transients occur during and following large earthquakes, and there are also strain transients not apparently associated with earthquakes. A particularly intriguing class of transients, for which there is a modest but growing list of examples, are preseismic anomalies. Such earthquake precursors, if further documented and understood, would have obvious importance for earthquake hazard mitigation. Because the timescales for these diverse transients range over at least 6 orders of magnitude (minutes to years), no single geodetic technique is optimum. We therefore undertook a systematic synthesis of Global Positioning Satellite (GPS) and borehole strainmeter data in three areas in California where there are adequate numbers of both types of instruments (or their equivalent): the San Francisco Bay region (within the Bay Area Regional Deformation network), southern California (within the Southern California Integrated GPS Network), and Parkfield (where a two-color laser system provides a proxy for continuous GPS measurements). An integral component of our study was the elucidation of the physical mechanisms by which such transients occur and propagate. We therefore initiated the development of multiple forward models, using two independent approaches. In the first, we explored the response to specified earthquake slip in viscoelastic models that incorporated failure criteria and the geometry of major faults in California. In the second approach, we examined the dynamical response of a complex rheological medium to the application of a far-field stress imposed by plate motions. The forward models were used both to gain insight into the range of strain transients to be expected under different assumed mechanical conditions and to develop representations for strain fields that allow GPS, borehole, and other strain data to be combined in a self-consistent, yet well-determined, manner. The models also provided a basis for hypothesis testing, by which data from a strain transient well characterized by GPS and borehole observations were utilized to distinguish among competing candidates for the causative physical mechanism and the governing physical characteristics. During the three years of this project, continued to a fourth year through a no-cost extension of the grant, we published 14 papers and presented or co-authored 37 papers at national scientific meetings.

Identification of AR(I)MA processes for modelling temporal correlations of GPS observations

NASA Astrophysics Data System (ADS)

Luo, X.; Mayer, M.; Heck, B.

2009-04-01

In many geodetic applications observations of the Global Positioning System (GPS) are routinely processed by means of the least-squares method. However, this algorithm delivers reliable estimates of unknown parameters und realistic accuracy measures only if both the functional and stochastic models are appropriately defined within GPS data processing. One deficiency of the stochastic model used in many GPS software products consists in neglecting temporal correlations of GPS observations. In practice the knowledge of the temporal stochastic behaviour of GPS observations can be improved by analysing time series of residuals resulting from the least-squares evaluation. This paper presents an approach based on the theory of autoregressive (integrated) moving average (AR(I)MA) processes to model temporal correlations of GPS observations using time series of observation residuals. A practicable integration of AR(I)MA models in GPS data processing requires the determination of the order parameters of AR(I)MA processes at first. In case of GPS, the identification of AR(I)MA processes could be affected by various factors impacting GPS positioning results, e.g. baseline length, multipath effects, observation weighting, or weather variations. The influences of these factors on AR(I)MA identification are empirically analysed based on a large amount of representative residual time series resulting from differential GPS post-processing using 1-Hz observation data collected within the permanent SAPOS® (Satellite Positioning Service of the German State Survey) network. Both short and long time series are modelled by means of AR(I)MA processes. The final order parameters are determined based on the whole residual database; the corresponding empirical distribution functions illustrate that multipath and weather variations seem to affect the identification of AR(I)MA processes much more significantly than baseline length and observation weighting. Additionally, the modelling results of temporal correlations using high-order AR(I)MA processes are compared with those by means of first order autoregressive (AR(1)) processes and empirically estimated autocorrelation functions.

Joint analysis of geodetic and earthquake fault-plane solution data to constrain magmatic sources: A case study from Kīlauea Volcano

USGS Publications Warehouse

Wauthier, Christelle; Roman, Diana C.; Poland, Michael

2016-01-01

A joint analysis of geodetic and seismic datasets from Kīlauea Volcano during a period of magmatic unrest in 2006 demonstrates the effectiveness of this combination for testing and constraining models of magma dynamics for a complex, multi-source system. At the end of 2003, Kīlauea's summit began a four-year-long period of inflation due to a surge in magma supply to the volcano. In 2006, for the first time since 1982, Kīlauea's Southwest Rift Zone (SWRZ) also experienced inflation. To investigate the characteristics of active magma sources and the nature of their interactions with faults in the SWRZ during 2006, we integrate, through Coulomb stress modeling, contemporary geodetic data from InSAR and GPS with a new catalogue of double-couple fault-plane solutions for volcano-tectonic earthquakes. We define two periods of inflation during 2006 based on the rate of deformation measured in daily GPS data, spanning February to 15 March 2006 (Period 1) and 16 March to 30 September 2006 (Period 2). InSAR data for these two periods are inverted to determine the position, change in size, and shape of inflation sources in each period. Our new models are consistent with microseismic activity from each period. They suggest that, during Period 1, deformation in the SWRZ can be explained by pressurization of magma in a spherical reservoir beneath the south caldera, and that, during Period 2, magma was also aseismically intruded farther to the southwest into the SWRZ along a sub-horizontal plane. Our Coulomb stress analysis shows that the microseismicity recorded in the SWRZ is induced by overpressurization of the south caldera reservoir, and not by magma intrusion into the SWRZ. This study highlights the importance of a joint analysis of independent geophysical datasets to fully constrain the nature of magma accumulation.

ON the interaction of the north andes plate with the caribbean and south american plates in northwestern south america from gps geodesy and seismic data

NASA Astrophysics Data System (ADS)

Pérez, Omar J.; Wesnousky, Steven G.; De La Rosa, Roberto; Márquez, Julio; Uzcátegui, Redescal; Quintero, Christian; Liberal, Luis; Mora-Páez, Héctor; Szeliga, Walter

2018-06-01

We examine the hypocentral distribution of seismicity and a series of geodetic velocity vectors obtained from Global Positioning System (GPS) observations between 1994 and 2015 both off-shore and mainland northwestern South America [66° W - 77° W; 8° N - 14° N]. Our analysis, that includes a kinematic block modeling, shows that east of the Caribbean-South American-North Andes plates triple junction at ˜68° W; 10.7° N, right-lateral easterly oriented shear motion (˜19.6 ± 2.0 mm/yr) between the Caribbean and South-America plates is split along two easterly striking, right-lateral strike slip subparallel fault zones: the San Sebastián fault that runs offshore the Venezuelan coast and slips about 17.0 ± 0.5 mm/yr, and the La Victoria fault, located onshore to the south, which is accumulating strain equivalent to 2.6 ± 0.4 mm/yr. West of the triple junction, relative right-lateral motion between the Caribbean and South American plates is mostly divided between the Morrocoy and Boconó fault systems which strike northwest and southwest from the triple junction, respectively, and bound the intervening North Andes plate that shows an easterly oriented geodetic slip of 15.0 ± 1.0 mm/yr relative to the South American plate. Slip on the Morrocoy fault is right-lateral and transtensional. Motion across the Boconó fault is also right-lateral but instead transpressional, divided between ˜9 to 11 mm/yr of right-slip on the Boconó fault and 2 to 5 mm/yr of convergence across adjacent and subparallel thrust faults. Farther west of the triple junction, ˜800 km away in northern Colombia, the Caribbean plate subducts to the southeast beneath the North Andes plate at a geodetically estimated rate of ˜5-7 mm/yr.

A new global plate velocity model using space geodetic data, REVEL

NASA Astrophysics Data System (ADS)

Sella, G. F.; Dixon, T. H.; Mao, A.; Stein, S.

2001-12-01

Our model describes the relative velocities of 19 plates and continental blocks, and is derived from publicly available space geodetic (primarily GPS) data for the period 1993-2000. We include an independent and rigorous estimate for GPS velocity uncertainties in order to assess plate rigidity, and propagate these uncertainties to the velocity predictions. By excluding sites that may be influenced by seismic cycle effects within the plate boundary zone as well sites affected by glacial isostatic adjustment, we believe the plate velocity model is representative of geologically Recent motions (last ~10,000 years) and have termed it REVEL, for Recent velocity. Departures from short term rigid plate behaviour due to glacial isostatic adjustment are clearly observed for North America and Eurasia. Australia shows possible differences from rigid plate behavior in a manner consistent with its mapped intraplate stress field. We see statistically significant differences between the velocity predictions of REVEL-2000 and those of the NUVEL-1A geologic model for about one third of tested plate pairs. Pacific-North America motion and motion of the Caribbean plate with respect to North and South America are significantly faster than NUVEL-1A, presumably reflecting systematic errors in the geological model because the relevant rate data do not reflect the full plate rate. Many other differences between the geodetic and geological models appear to reflect real velocity changes over the last few million years. Nubia-Arabia and Arabia-Eurasia appear to be slowing, perhaps related to the collision of Arabia with Eurasia and consequent increased resistance to Arabia's northward motion Several other plate pairs, including Nazca-Pacific, Nazca-South America and Nubia-South America, are experiencing gradual slowing that dates back to about 25 Ma. This is the time of the initiation of the modern Andes mountains, and we speculate that associated crustal thickening on the leading edge of South America may play a role in this deceleration by affecting the balance of plate driving forces.

New infrastructure at Alboran island (Western Mediterranean): a submarine and on-land Geophysical Observatory

NASA Astrophysics Data System (ADS)

Pazos, Antonio; Martín Davila, José; Buforn, Elisa; Jesús García Fernández, Maria; Bullón, Mercedes; Gárate, Jorge

2010-05-01

The Eurasian-African plate boundary crosses the called "Ibero-Maghrebian" region from San Vicente Cape (SW Portugal) to Tunisia including the South of Iberia, Alboran Sea, and northern of Morocco and Algeria. The low convergence rate at this plate boundary produces a continuous moderate seismic activity of low magnitude and shallow depth, where the occurrence of large earthquakes is separated by long time intervals. In this region, there are also intermediate and very deep earthquakes. Since more than hundred years ago San Fernando Naval Observatory (ROA), in collaboration with other Institutes, has deployed different geophysical and geodetic equipment in the Southern Spain - North-western Africa area in order to study this broad deformation. Currently a Broad Band seismic net (Western Mediterranean, WM net), a permanent geodetic GPS net and a Geomagnetic Observatory have been installed by ROA in this area. To complement the available data, since past October a permanent marine-on land geophysical observatory is being installed by ROA in Alboran Island and surrounding marine zones. Till now the following facilities has been installed: • Submarine: 2 km submarine fibre optics cable (power and data transmission); Broad Band Seismometer (CMG-3T, buried); Accelerometer (Guralp 3 channels), buried); Differential Pressure Gauge (DPG); Thermometer. • On land: Permanent geodetic GPS station; Automatic meteorological station; Data acquisition system for submarine equipment; Satellite Data Transmission system. Data are already being transmitted in real time to ROA headquarters via satellite Intranet. The marine part, currently installed in a 50 m depth platform, has been designed to be enlarged by extending the cable to greater depths and/or installing additional submarine equipment, such a way in short an ADCP profiler will be installed. In this work we aim to show the present status, scientific possibilities and the next future plans of this submarine-on land installation.

Joint analysis of geodetic and earthquake fault-plane solution data to constrain magmatic sources: A case study from Kīlauea Volcano

NASA Astrophysics Data System (ADS)

Wauthier, Christelle; Roman, Diana C.; Poland, Michael P.

2016-12-01

A joint analysis of geodetic and seismic datasets from Kīlauea Volcano during a period of magmatic unrest in 2006 demonstrates the effectiveness of this combination for testing and constraining models of magma dynamics for a complex, multi-source system. At the end of 2003, Kīlauea's summit began a four-year-long period of inflation due to a surge in magma supply to the volcano. In 2006, for the first time since 1982, Kīlauea's Southwest Rift Zone (SWRZ) also experienced inflation. To investigate the characteristics of active magma sources and the nature of their interactions with faults in the SWRZ during 2006, we integrate, through Coulomb stress modeling, contemporary geodetic data from InSAR and GPS with a new catalogue of double-couple fault-plane solutions for volcano-tectonic earthquakes. We define two periods of inflation during 2006 based on the rate of deformation measured in daily GPS data, spanning February to 15 March 2006 (Period 1) and 16 March to 30 September 2006 (Period 2). InSAR data for these two periods are inverted to determine the position, change in size, and shape of inflation sources in each period. Our new models are consistent with microseismic activity from each period. They suggest that, during Period 1, deformation in the SWRZ can be explained by pressurization of magma in a spherical reservoir beneath the south caldera, and that, during Period 2, magma was also aseismically intruded farther to the southwest into the SWRZ along a sub-horizontal plane. Our Coulomb stress analysis shows that the microseismicity recorded in the SWRZ is induced by overpressurization of the south caldera reservoir, and not by magma intrusion into the SWRZ. This study highlights the importance of a joint analysis of independent geophysical datasets to fully constrain the nature of magma accumulation.

Rapid Geodetic Shortening Across the Eastern Cordillera of NW Argentina Observed by the Puna-Andes GPS Array

NASA Astrophysics Data System (ADS)

McFarland, Phillip K.; Bennett, Richard A.; Alvarado, Patricia; DeCelles, Peter G.

2017-10-01

We present crustal velocities for 29 continuously recording GPS stations from the southern central Andes across the Puna, Eastern Cordillera, and Santa Barbara system for the period between the 27 February 2010 Maule and 1 April 2014 Iquique earthquakes in a South American frame. The velocity field exhibits a systematic decrease in magnitude from 35 mm/yr near the trench to <1 mm/yr within the craton. We forward model loading on the Nazca-South America (NZ-SA) subduction interface using back slip on elastic dislocations to approximate a fully locked interface from 10 to 50 km depth. We generate an ensemble of models by iterating over the percentage of NZ-SA convergence accommodated at the subduction interface. Velocity residuals calculated for each model demonstrate that locking on the NZ-SA interface is insufficient to reproduce the observed velocities. We model deformation associated with a back-arc décollement using an edge dislocation, estimating model parameters from the velocity residuals for each forward model of the subduction interface ensemble using a Bayesian approach. We realize our best fit to the thrust-perpendicular velocity field with 70 ± 5% of NZ-SA convergence accommodated at the subduction interface and a slip rate of 9.1 ± 0.9 mm/yr on the fold-thrust belt décollement. We also estimate a locking depth of 14 ± 9 km, which places the downdip extent of the locked zone 135 ± 20 km from the thrust front. The thrust-parallel component of velocity is fit by a constant shear strain rate of -19 × 10-9 yr-1, equivalent to clockwise rigid block rotation of the back arc at a rate of 1.1°/Myr.

Capturing Postseismic Processes of the 2016 Mw 7.1 Kumamoto Earthquake, Japan, Using Dense, Continuous GPS and Short-repeat Time ALOS-2 InSAR Data: Implications for the Shallow Slip Deficit Problem

NASA Astrophysics Data System (ADS)

Milliner, C. W. D.; Burgmann, R.; Wang, T.; Inbal, A.; Bekaert, D. P.; Liang, C.; Fielding, E. J.

2017-12-01

Separating the contribution of shallow coseismic slip from rapidly decaying, postseismic afterslip in surface rupturing events has been difficult to resolve due to the typically sparse configuration of GPS networks and long-repeat time of InSAR acquisitions. Whether shallow fault motion along surface ruptures is a result of coseismic slip, or largely a product of rapid afterslip occurring within the first minutes to days, has significant implications for our understanding of the mechanics and frictional behavior of faulting in the shallow crust. To test this behavior in the case of a major surface rupturing event, we attempt to quantify the co- and postseismic slip of the 2016 Mw 7.1 Kumamoto earthquake sequence using a dense and continuous GPS network ( 10 km spacing), with short-repeat time, ALOS-2 InSAR data. Using the Network Inversion Filter method, we jointly invert the GPS and InSAR data to obtain a time history of afterslip in the first minutes to months following the mainshock. From our initial results, we find no clear evidence of significant shallow afterslip (i.e., no observable slip > 30 cm at depths of < 3 km, a minimum resolvable value), that could account for the 1 m of coseismic deficit of shallow slip inferred from our static finite-fault inversion. Our results show, aside from significant volumetric changes related to poroelastic processes, the majority of shallow fault slip was largely complete after rupture cessation. We also attempt to improve our coseismic slip model by implementing a method that inverts changes in seismicity rates for coseismic slip, helping constrain parts of the model space at depth where geodetic data loses resolving power. The use of geodetic data with the ability to resolve near-field, coseismic deformation and rapidly decaying postseismic processes will aid in our understanding of the frictional properties of shallow faulting, giving more reliable predictions for ground motion simulations and seismic hazard assessments.

Directional antenna array (DAA) for communications, control, and data link protection

NASA Astrophysics Data System (ADS)

Molchanov, Pavlo A.; Contarino, Vincent M.

2013-06-01

A next generation of Smart antennas with point-to-point communication and jam, spoof protection capability by verification of spatial position is offered. A directional antenna array (DAA) with narrow irradiation beam provides counter terrorism protection for communications, data link, control and GPS. Communications are "invisible" to guided missiles because of 20 dB smaller irradiation outside the beam and spatial separation. This solution can be implemented with current technology. Directional antennas have higher gain and can be multi-frequency or have wide frequency band in contrast to phase antenna arrays. This multi-directional antenna array provides a multi-functional communication network and simultaneously can be used for command control, data link and GPS.

Assessment Study of Using Online (CSRS) GPS-PPP Service for Mapping Applications in Egypt

NASA Astrophysics Data System (ADS)

Abd-Elazeem, Mohamed; Farah, Ashraf; Farrag, Farrag

2011-09-01

Many applications in navigation, land surveying, land title definitions and mapping have been made simpler and more precise due to accessibility of Global Positioning System (GPS) data, and thus the demand for using advanced GPS techniques in surveying applications has become essential. The differential technique was the only source of accurate positioning for many years, and remained in use despite of its cost. The precise point positioning (PPP) technique is a viable alternative to the differential positioning method in which a user with a single receiver can attain positioning accuracy at the centimeter or decimeter scale. In recent years, many organizations introduced online (GPS-PPP) processing services capable of determining accurate geocentric positions using GPS observations. These services provide the user with receiver coordinates in free and unlimited access formats via the internet. This paper investigates the accuracy of the Canadian Spatial Reference System (CSRS) Precise Point Positioning (PPP) (CSRS-PPP) service supervised by the Geodetic Survey Division (GSD), Canada. Single frequency static GPS observations have been collected at three points covering time spans of 60, 90 and 120 minutes. These three observed sites form baselines of 1.6, 7, and 10 km, respectively. In order to assess the CSRS-PPP accuracy, the discrepancies between the CSRS-PPP estimates and the regular differential GPS solutions were computed. The obtained results illustrate that the PPP produces a horizontal error at the scale of a few decimeters; this is accurate enough to serve many mapping applications in developing countries with a savings in both cost and experienced labor.

Software for Generating Troposphere Corrections for InSAR Using GPS and Weather Model Data

NASA Technical Reports Server (NTRS)

Moore, Angelyn W.; Webb, Frank H.; Fishbein, Evan F.; Fielding, Eric J.; Owen, Susan E.; Granger, Stephanie L.; Bjoerndahl, Fredrik; Loefgren, Johan; Fang, Peng; Means, James D.;

Active NE-SW Compressional Strain Within the Arabian Plate

NASA Astrophysics Data System (ADS)

Floyd, M. A.; ArRajehi, A.; King, R. W.; McClusky, S.; Reilinger, R. E.; Douad, M.; Sholan, J.; Bou-Rabee, F.

2012-12-01

Motion of the Arabian plate with respect to Eurasia has been remarkably steady over more than 25 Myr as revealed by comparison of geodetic and plate tectonic reconstructions (e.g., McQuarrie et al., 2003, GRL; ArRajehi et al., 2010, Tectonics). While internal plate deformation is small in comparison to the rate of Arabia-Eurasia convergence, the improved resolution of GPS observations indicate ~ NE-SW compressional strain that appears to affect much of the plate south of latitude ~ 30°N. Seven ~ NE-SW oriented inter-station baselines all indicated shortening at rates in the range of 0.5-2 mm/yr, for the most part with 1-sigma velocity uncertainties < 0.4 mm/yr. Plate-scale strain rates exceed 2×10-9/yr. The spatial distribution of strain can not be resolved from the sparse available data, but strain appears to extend at least to Riyadh, KSA, ~ 600 km west of the Zagros Fold and Thrust Belt that forms the eastern, collisional boundary of the Arabian plate with Eurasia (Iran). Geodetic velocities in the plate tectonic reference frame for Arabia, derived from magnetic anomalies in the Red Sea (Chu and Gordon, 1998, GJI), show no significant E-W motion for GPS stations located along the Red Sea coast (i.e., geodetic and plate tectonic spreading rates across the Red Sea agree within their resolution), in contrast to sites in the plate interior and along the east side of the plate that indicate east-directed motions. In addition, NE-SW contraction is roughly normal to ~ N-S striking major structural folds in the sedimentary rocks within the Arabian Platform. These relationships suggest that geodetically observed contraction has characterized the plate for at least the past ~ 3 Myr. Broad-scale contraction of the Arabian plate seems intuitively reasonable given that the east and north sides of the plate are dominated by active continental collision (Zagros, E Turkey/Caucasus) while the west and south sides are bordered by mid-ocean ridge spreading (Red Sea and Gulf of Aden). While the dynamic processes responsible for the observed strain remain speculative, we are investigating models involving long-range effects of the Arabia-Eurasia collision, ridge-push along the Red Sea and Gulf of Aden, and gravitational spreading of the higher elevation Arabian Shield towards the lower elevation platform.

Terrestrial Reference Frame from GPS and SLR

NASA Astrophysics Data System (ADS)

Weiss, Jan; Bertiger, Willy; Desai, Shailen; Haines, Bruce; Sibois, Aurore

2015-04-01

We present strategies for realizing the terrestrial reference frame (TRF) using tracking data from terrestrial GPS receivers alone and in tandem with the GRACE and LAGEOS satellites. We generate solutions without apriori ties to the International Terrestrial Reference Frame (ITRF). Our approach relies on processing multi-day orbit arcs to take advantage of the satellite dynamics, GPS receiver and transmitter calibrations derived from low-Earth orbiter (LEO) data, and estimation strategies tuned for realizing a stable and accurate TRF. We furthermore take advantage of the geometric diversity provided by GPS tracking from GRACE, and explore the impacts of including ground-based satellite laser range (SLR) measurements to LAGEOS-1 and -2 with local ties relating the two geodetic techniques. We process data from 2003-2014 and compute Helmert transformations relative to ITRF/IGb08. With GPS alone we achieve a 3D origin offset and rate of <7 mm and <1 mm/yr, and reduce the offset to <4 mm when GRACE is included in the global solutions. Scale bias and rate are 3.1 ppb and 0.01 ppb/yr in either solution. Including SLR tracking from 11 ground stations to the LAGEOS satellites from 2012-2014 yields a reduction in scale bias of 0.5-1.0 ppb depending on the weight assigned to the SLR measurements. However, scatter is increased due to the relatively sparse SLR tracking network. We conclude with approaches for improving the TRF realized from GPS and SLR combined at the measurement level.

Physical applications of GPS geodesy: a review.

PubMed

Bock, Yehuda; Melgar, Diego

2016-10-01

Geodesy, the oldest science, has become an important discipline in the geosciences, in large part by enhancing Global Positioning System (GPS) capabilities over the last 35 years well beyond the satellite constellation's original design. The ability of GPS geodesy to estimate 3D positions with millimeter-level precision with respect to a global terrestrial reference frame has contributed to significant advances in geophysics, seismology, atmospheric science, hydrology, and natural hazard science. Monitoring the changes in the positions or trajectories of GPS instruments on the Earth's land and water surfaces, in the atmosphere, or in space, is important for both theory and applications, from an improved understanding of tectonic and magmatic processes to developing systems for mitigating the impact of natural hazards on society and the environment. Besides accurate positioning, all disturbances in the propagation of the transmitted GPS radio signals from satellite to receiver are mined for information, from troposphere and ionosphere delays for weather, climate, and natural hazard applications, to disturbances in the signals due to multipath reflections from the solid ground, water, and ice for environmental applications. We review the relevant concepts of geodetic theory, data analysis, and physical modeling for a myriad of processes at multiple spatial and temporal scales, and discuss the extensive global infrastructure that has been built to support GPS geodesy consisting of thousands of continuously operating stations. We also discuss the integration of heterogeneous and complementary data sets from geodesy, seismology, and geology, focusing on crustal deformation applications and early warning systems for natural hazards.

Earth Surface Deformation in the North China Plain Detected by Joint Analysis of GRACE and GPS Data

PubMed Central

Liu, Renli; Li, Jiancheng; Fok, Hok Sum; Shum, C.K.; Li, Zhao

2014-01-01

Mass redistribution of the Earth causes variable loading that deforms the solid Earth. While most recent studies using geodetic techniques focus on regions (such as the Amazon basin and the Nepal Himalayas) with large seasonal deformation amplitudes on the order of 1–4 cm due to hydrologic loading, few such studies have been conducted on the regions where the seasonal deformation amplitude is half as large. Here, we use joint GPS and GRACE data to investigate the vertical deformation due to hydrologic loading in the North China Plain, where significant groundwater depletion has been reported. We found that the GPS- and GRACE-derived secular trends and seasonal signals are in good agreement, with an uplift magnitude of 1–2 mm/year and a correlation of 85.0%–98.5%, respectively. This uplift rate is consistent with groundwater depletion rate estimated from GRACE data and in-situ groundwater measurements from earlier report studies; whereas the seasonal hydrologic variation reflects human behavior of groundwater pumping for agriculture irrigation in spring, leading to less water storage in summer than that in the winter season. However, less than 20% of weighted root-mean-squared (WRMS) reductions were detected for all the selected GPS stations when GRACE-derived seasonal deformations were removed from detrended GPS height time series. This discrepancy is probably because the GRACE-derived seasonal signals are large-scale, while the GPS-derived signals are local point measurements. PMID:25340454

Earth surface deformation in the North China Plain detected by joint analysis of GRACE and GPS data.

PubMed

Liu, Renli; Li, Jiancheng; Fok, Hok Sum; Shum, C K; Li, Zhao

2014-10-22

Mass redistribution of the Earth causes variable loading that deforms the solid Earth. While most recent studies using geodetic techniques focus on regions (such as the Amazon basin and the Nepal Himalayas) with large seasonal deformation amplitudes on the order of 1-4 cm due to hydrologic loading, few such studies have been conducted on the regions where the seasonal deformation amplitude is half as large. Here, we use joint GPS and GRACE data to investigate the vertical deformation due to hydrologic loading in the North China Plain, where significant groundwater depletion has been reported. We found that the GPS- and GRACE-derived secular trends and seasonal signals are in good agreement, with an uplift magnitude of 1-2 mm/year and a correlation of 85.0%-98.5%, respectively. This uplift rate is consistent with groundwater depletion rate estimated from GRACE data and in-situ groundwater measurements from earlier report studies; whereas the seasonal hydrologic variation reflects human behavior of groundwater pumping for agriculture irrigation in spring, leading to less water storage in summer than that in the winter season. However, less than 20% of weighted root-mean-squared (WRMS) reductions were detected for all the selected GPS stations when GRACE-derived seasonal deformations were removed from detrended GPS height time series. This discrepancy is probably because the GRACE-derived seasonal signals are large-scale, while the GPS-derived signals are local point measurements.

Testing the Dependence of Airborne Gravity Results on Three Variables in Kinematic GPS Processing

NASA Astrophysics Data System (ADS)

Weil, C.; Diehl, T. M.

2011-12-01

The National Geodetic Survey's Gravity for the Redefinition of the American Vertical Datum (GRAV-D) program plans to collect airborne gravity data across the entire U.S. and its holdings over the next decade. The goal is to build a geoid accurate to 1-2 cm, for which the airborne gravity data is key. The first phase is underway, with > 13% of data collection completed in: parts of Alaska, parts of California, most of the Gulf Coast, Puerto Rico, and the Virgin Islands. Obtaining accurate airborne gravity survey results depends on the quality of the GPS/IMU position solution used in the processing. There are many factors that could have an influence on the positioning results. First, we will investigate how an increased data sampling rate for the GPS/IMU affects the position solution and accelerations derived from those positions. Second we will test the hypothesis that, for differential kinematic processing a better solution is obtained using both a base and a rover GPS unit that contain an additional rubidium clock that is reported to sync better with GPS time. Finally, we will look at a few different GPS+IMU processing methods available in commercial software. This includes comparing GPS-only solutions with loosely coupled GPS/IMU solutions from the Applanix POSAV-510 system and tightly coupled solutions with our newly-acquired NovAtel SPAN system (micro-IRS IMU). Differential solutions are compared with PPP (Precise Point Positioning) solutions along with multi-pass and advanced tropospheric corrections available with the NovAtel Inertial Explorer software. Based on preliminary research, we expect that the tightly-coupled solutions with either better troposphere and/or multi-pass solutions will provide superior position (and gravity) results.

Self-calibrating pseudolite arrays: Theory and experiment

NASA Astrophysics Data System (ADS)

Lemaster, Edward Alan

Tasks envisioned for future-generation Mars rovers---sample collection, area survey, resource mining, habitat construction, etc.---will require greatly enhanced navigational capabilities over those possessed by the 1997 Mars Sojourner rover. Many of these tasks will involve cooperative efforts by multiple rovers and other agents, necessitating both high accuracy and the ability to share navigation information among different users. On Earth, satellite-based carrier-phase differential GPS provides a means of delivering centimeter-level, drift-free positioning to multiple users in contact with a reference base station. It would be highly desirable to have a similar navigational capability for use in Mars exploration. This research has originated a new local-area navigation system---a Self-Calibrating Pseudolite Array (SCPA)---that can provide centimeter-level localization to multiple rovers by utilizing GPS-based pseudolite transceivers deployed in a ground-based array. Such a system of localized beacons can replace or augment a system based on orbiting satellite transmitters. Previous pseudolite arrays have relied upon a priori information to survey the locations of the pseudolites, which must be accurately known to enable navigation within the array. In contrast, an SCPA does not rely upon other measurement sources to determine these pseudolite locations. This independence is a key requirement for autonomous deployment on Mars, and is accomplished through the use of GPS transceivers containing both transmit and receive components and through algorithms that utilize limited motion of a transceiver-bearing rover to determine the locations of the stationary transceivers. This dissertation describes the theory and operation of GPS transceivers, and how they can be used for navigation within a Self-Calibrating Pseudolite Array. It presents new algorithms that can be used to self-survey such arrays robustly using no a priori information, even under adverse conditions such as high-multipath environments. It then describes the experimental SCPA prototype developed at Stanford University and used in conjunction with the K9 Mars rover operated by NASA Ames Research Center. Using this experimental system, it provides experimental validation of both successful positioning using GPS transceivers and full calibration of an SCPA following deployment in an unknown configuration.

Fault-slip directions in central and southern Greece measured from striated and corrugated fault planes: Comparison with focal mechanism and geodetic data

NASA Astrophysics Data System (ADS)

Roberts, Gerald P.; Ganas, Athanassios

2000-10-01

Fault-slip directions recorded by outcropping striated and corrugated fault planes in central and southern Greece have been measured for comparison with extension directions derived from focal mechanism and Global Positioning System (GPS) data for the last ˜100 years to test how far back in time velocity fields and deformation dynamics derived from the latter data sets can be extrapolated. The fault-slip data have been collected from the basin-bounding faults to Plio-Pleistocene to recent extensional basins and include data from arrays of footwall faults formed during the early stages of fault growth. We show that the orientation of the inferred stress field varies along faults and earthquake ruptures, so we use only slip-directions from the centers of faults, where dip-slip motion occurs, to constrain regionally significant extension directions. The fault-slip directions for the Peloponnese and Gulfs of Evia and Corinth are statistically different at the 99% confidence level but statistically the same as those implied by earthquake focal mechanisms for each region at the 99% confidence level; they are also qualitatively similar to the principal strain axes derived from GPS studies. Extension directions derived from fault-slip data are 043-047° for the southern Peloponnese, 353° for the Gulf of Corinth, and 015-014° for the Gulf of Evia. Extension on active normal faults in the two latter areas appears to grade into strike-slip along the North Anatolian Fault through a gradual change in fault-slip directions and fault strikes. To reconcile the above with 5° Myr-1 clockwise rotations suggested for the area, we suggest that the faults considered formed during a single phase of extension. The deformation and formation of the normal fault systems examined must have been sufficiently rapid and recent for rotations about vertical axes to have been unable to disperse the fault-slip directions from the extension directions implied by focal mechanisms and GPS data. Thus, in central and southern Greece the velocity fields derived from focal mechanism and GPS data may help explain the dynamics of the deformation over longer time periods than the ˜100 years over which they were measured; this may include the entire deformation history of the fault systems considered, a time period that may exceed 1-2 Myr.

LONG-TERM STABILITY OF THE LOCAL GROUND CONTROL NETWORK AT THE CO-LOCATION SITE OF MEDICINA

NASA Astrophysics Data System (ADS)

Abbondanza, C.; Sarti, P.; Legrand, J.

2009-12-01

ITRF combinations rely on the availability of accurate tie vectors linking reference points of space geodetic techniques. Co-located instruments are assumed to move consistently and no local relative motion is taken into account. Instabilities may degrade the quality of the co-location itself and perturb the result of ITRF combinations. This work aims to determine the stability of the local ground control network at Medicina (Italy) with independent surveying methods. The observatory hosts a co-location between a VLBI telescope and two GPS antennas, MEDI and MSEL. It is located in the Po Plain where thick layers of clays are the prevalent soil characteristics. Hence, provision of long term stability of geodetic monuments is a challenge and monitoring their stability is an issue. MEDI and the VLBI station regularly contribute to the determination of ITRF, while MSEL is part of the EUREF network. A set of five tie vectors observations linking the VLBI and MEDI reference points was acquired between 2001 and 2007. It is our main tool for performing local deformation analysis. Additionally, the GPS time series of MEDI and MSEL were used to cross check and confirm the local instability detected by terrestrial methods. To achieve a rigorous and reliable investigation of the local stability, multi-epoch terrestrial observations were homogeneously processed according to common parameterizations in a consistent reference frame. Similarly, continuous GPS observations from MEDI and MSEL were analysed according to the new EPN reprocessing strategy in order to monitor the short baseline between MEDI and MSEL; to spotlight any change in its length. Both approaches confirm differential motions at the site which can be related to monument instabilities originated by the particularly unfavourable local geological setting and the inapt design of the monuments foundation. The monuments move non homogeneously at rates reaching up to 1.6 mm/year, this value being comparable to intra-plate tectonic deformations. Evidences of relative motion between MEDI and MSEL are found: an annual signal with amplitude ≈1.3 mm is detected along the East component and an 80 weeks signal with amplitude ≈1.1 mm is found along the vertical component of the baseline. The combination of the two independent observing techniques confirms the importance of repeatedly performed terrestrial surveys and the presence of intra-technique co-locations at geodetic sites. Although available, VLBI observations were not considered since we are interested in detecting local relative motions in a very restricted area (100m x 100m) avoiding problems of datum consistencies between different space geodetic techniques. In fact, the combination of technique-specific frames might originate local inconsistencies on station positions due to misalignments of tie vectors in the global reference frame. These inconsistencies might degrade the accuracy of the displacement analysis and can be difficult to deal with.

Retrieval and Validation of Zenith and Slant Path Delays From the Irish GPS Network

NASA Astrophysics Data System (ADS)

Hanafin, Jennifer; Jennings, S. Gerard; O'Dowd, Colin; McGrath, Ray; Whelan, Eoin

2010-05-01

Retrieval of atmospheric integrated water vapour (IWV) from ground-based GPS receivers and provision of this data product for meteorological applications has been the focus of a number of Europe-wide networks and projects, most recently the EUMETNET GPS water vapour programme. The results presented here are from a project to provide such information about the state of the atmosphere around Ireland for climate monitoring and improved numerical weather prediction. Two geodetic reference GPS receivers have been deployed at Valentia Observatory in Co. Kerry and Mace Head Atmospheric Research Station in Co. Galway, Ireland. These two receivers supplement the existing Ordnance Survey Ireland active network of 17 permanent ground-based receivers. A system to retrieve column-integrated atmospheric water vapour from the data provided by this network has been developed, based on the GPS Analysis at MIT (GAMIT) software package. The data quality of the zenith retrievals has been assessed using co-located radiosondes at the Valentia site and observations from a microwave profiling radiometer at the Mace Head site. Validation of the slant path retrievals requires a numerical weather prediction model and HIRLAM (High-Resolution Limited Area Model) version 7.2, the current operational forecast model in use at Met Éireann for the region, has been used for this validation work. Results from the data processing and comparisons with the independent observations and model will be presented.

Anti-Jam GPS Antennas for Wearable Dismounted Soldier Navigation Systems

DTIC Science & Technology

2016-06-01

in this report are not to be construed as an official Department of the Army position unless so designated by other authorized documents. Citation...Approaches for the design and fabrication of a wearable anti-jam global positioning system (GPS) antenna are explored to support accurate and uninterrupted...including GPS antenna element and array designs , and algorithms for jammer mitigation, and the candidate technologies best fit for wearable anti-jam GPS

On principles, methods and recent advances in studies towards a GPS-based control system for geodesy and geodynamics

NASA Technical Reports Server (NTRS)

Delikaraoglou, Demitris

1989-01-01

Although Very Long Baseline Interferometry (VLBI) and Satellite Laser Ranging (SLR) are becoming increasingly important tools for geodynamic studies, their future role may well be fulfilled by using alternative techniques such as those utilizing the signals from the Global Positioning System (GPS). GPS, without the full implementation of the system, already offers a favorable combination of cost and accuracy and has consistently demonstrated the capability to provide high precision densification control in the regional and local areas of the VLBI and SLR networks. This report reviews VLBI and SLR vis-a-vis GPS and outlines the capabilities and limitations of each technique and how their complementary application can be of benefit to geodetic and geodynamic operations. It demonstrates, albeit with a limited data set, that dual-frequency GPS observations and interferometric type analysis techniques make possible the modelling of the GPS orbits for several days with an accuracy of a few meters. The use of VLBI or SLR sites as fiducial stations together with refinements in the orbit determination procedures can greatly reduce the systematic errors in the GPS satellite orbits used to compute the positions of non-fiducial locations. In general, repeatability and comparison with VLBI of the GPS determined locations are of the order of between 2 parts in 10 to the 7th power and 5 parts in 10 to the 8th power for baseline lengths less than 2000 km. This report is mainly a synthesis of problems, assumptions, methods and recent advances in the studies towards the establishment of a GPS-based system for geodesy and geodynamics and is one phase in the continuing effort for the development of such a system. To some, including the author, it seems reasonable to expect within the next few years that more evidence will show GPS to be as a powerful and reliable a tool as mobile VLBI and SLR are today, but largely more economical.

Precision assessment of the orthometric heights determination in northern part of Algeria by combining the GPS data and the local geoid model

NASA Astrophysics Data System (ADS)

Benahmed Daho, Sid Ahmed

2010-02-01

The main purpose of this article is to discuss the use of GPS positioning together with a gravimetrically determined geoid, for deriving orthometric heights in the North of Algeria, for which a limited number of GPS stations with known orthometric heights are available, and to check, by the same opportunity, the possibility of substituting the classical spirit levelling. For this work, 247 GPS stations which are homogeneously distributed and collected from the international TYRGEONET project, as well as the local GPS/Levelling surveys, have been used. The GPS/Levelling geoidal heights are obtained by connecting the points to the levelling network while gravimetric geoidal heights were interpolated from the geoid model computed by the Geodetic Laboratory of the National Centre of Spatial Techniques from gravity data supplied by BGI. However, and in order to minimise the discordances, systematic errors and datum inconsistencies between the available height data sets, we have tested two parametric models of corrector surface: a four parameter transformation and a third polynomial model are used to find the adequate functional representation of the correction that should be applied to the gravimetric geoid. The comparisons based on these GPS campaigns prove that a good fit between the geoid model and GPS/levelling data has been reached when the third order polynomial was used as corrector surface and that the orthometric heights can be deducted from GPS observations with an accuracy acceptable for the low order levelling network densification. In addition, the adopted methodology has been also applied for the altimetric auscultation of a storage reservoir situated at 40 km from the town of Oran. The comparison between the computed orthometric heights and observed ones allowed us to affirm that the alternative of levelling by GPS is attractive for this auscultation.

GPS-Based Precision Baseline Reconstruction for the TanDEM-X SAR-Formation

NASA Technical Reports Server (NTRS)

Montenbruck, O.; vanBarneveld, P. W. L.; Yoon, Y.; Visser, P. N. A. M.

2007-01-01

The TanDEM-X formation employs two separate spacecraft to collect interferometric Synthetic Aperture Radar (SAR) measurements over baselines of about 1 km. These will allow the generation ofa global Digital Elevation Model (DEM) with an relative vertical accuracy of 2-4 m and a 10 m ground resolution. As part of the ground processing, the separation of the SAR antennas at the time of each data take must be reconstructed with a 1 mm accuracy using measurements from two geodetic grade GPS receivers. The paper discusses the TanDEM-X mission as well as the methods employed for determining the interferometric baseline with utmost precision. Measurements collected during the close fly-by of the two GRACE satellites serve as a reference case to illustrate the processing concept, expected accuracy and quality control strategies.

Geodetic deformation monitoring at Pendidikan Diponegoro Dam

NASA Astrophysics Data System (ADS)

Yuwono, Bambang Darmo; Awaluddin, Moehammad; Yusuf, M. A.; Fadillah, Rizki

2017-07-01

Deformation monitoring is one indicator to assess the feasibility of Dam. In order to get the correct result of the deformation, it is necessary to determine appropriate deformation monitoring network and the observation data should be analyse and evaluated carefully. Measurement and analysis of deformation requires relatively accurate data and the precision is high enough, one of the observation method that used is GPS (Global Positioning System). The research was conducted at Pendidikan Undip Dams is Dam which is located in Tembang. Diponegoro Dam was built in 2013 and a volume of 50.86 m3 of water, inundation normal width of up to 13,500 m2. The main purpose of these building is not only for drainage but also for education and micro hydro power plant etc. The main goal of this reasearch was to monitor and analyze the deformation at Pendidikan Undip Dam and to determaine whether GPS measurement could meet accuracy requirement for dam deformation measurements. Measurements were made 2 times over 2 years, 2015 and 2016 using dual frequency GPS receivers with static methods and processed by Scientific Software GAMIT 10.6

Potential Seasonal Terrestrial Water Storage Monitoring from GPS Vertical Displacements: A Case Study in the Lower Three-Rivers Headwater Region, China

PubMed Central

Zhang, Bao; Yao, Yibin; Fok, Hok Sum; Hu, Yufeng; Chen, Qiang

2016-01-01

This study uses the observed vertical displacements of Global Positioning System (GPS) time series obtained from the Crustal Movement Observation Network of China (CMONOC) with careful pre- and post-processing to estimate the seasonal crustal deformation in response to the hydrological loading in lower three-rivers headwater region of southwest China, followed by inferring the annual EWH changes through geodetic inversion methods. The Helmert Variance Component Estimation (HVCE) and the Minimum Mean Square Error (MMSE) criterion were successfully employed. The GPS inferred EWH changes agree well qualitatively with the Gravity Recovery and Climate Experiment (GRACE)-inferred and the Global Land Data Assimilation System (GLDAS)-inferred EWH changes, with a discrepancy of 3.2–3.9 cm and 4.8–5.2 cm, respectively. In the research areas, the EWH changes in the Lancang basin is larger than in the other regions, with a maximum of 21.8–24.7 cm and a minimum of 3.1–6.9 cm. PMID:27657064

Study of the active deformation of Mitidja (Tell Atlas, Algeria) by GPS

NASA Astrophysics Data System (ADS)

Bacha, Wahab; Masson, Frederic; Yelles-Chaouche, Abdelkrim; Lammali, Kamel; Bellik, Amar; Hamai, Lamine

2013-04-01

A network was created in the Mitidja region around the capital Algiers (Algeria). It has been established to study the deformation of the region and the slow operation of flaws in it. The network was installed by a distribution of GPS stations according to structural domains existing in the region. Twelve bases spread across the study area, have been installed. The measurements were acquired by performing four measurement campaigns in 2006, 2007, 2009 and 2010, with sessions over a month of action. This work allowed the installation of a geodetic network of regional monitoring by methodology GPS in the zone of Mitidja (Tellian Atlas, Algeria). Four observation campaigns were carried out on this area with session's superiors in one month of measurements. The treatment was carried out with software GAMIT-GLOBK, the network is attached to several world stations IGS treated between 2000-2010, indexed in a precise frame of reference ITRF05. The results presented in this memory show a deformation in shortening ≤ 0.5 mm/an in the plain of Mitidja and the surrounding Solid masses.

Coseismic slip distribution of the February 27, 2010 Mw 8.9 Maule, Chile earthquake

USGS Publications Warehouse

Pollitz, Fred F.; Brooks, Ben; Tong, Xiaopeng; Bevis, Michael G.; Foster, James H.; Burgmann, Roland

2011-01-01

[1] Static offsets produced by the February 27, 2010 Mw = 8.8 Maule, Chile earthquake as measured by GPS and InSAR constrain coseismic slip along a section of the Andean megathrust of dimensions 650 km (in length) × 180 km (in width). GPS data have been collected from both campaign and continuous sites sampling both the near-field and far field. ALOS/PALSAR data from several ascending and descending tracks constrain the near-field crustal deformation. Inversions of the geodetic data for distributed slip on the megathrust reveal a pronounced slip maximum of order 15 m at ∼15–25 km depth on the megathrust offshore Lloca, indicating that seismic slip was greatest north of the epicenter of the bilaterally propagating rupture. A secondary slip maximum appears at depth ∼25 km on the megathrust just west of Concepción. Coseismic slip is negligible below 35 km depth. Estimates of the seismic moment based on different datasets and modeling approaches vary from 1.8 to 2.6 × 1022 N m. Our study is the first to model the static displacement field using a layered spherical Earth model, allowing us to incorporate both near-field and far-field static displacements in a consistent manner. The obtained seismic moment of 1.97 × 1022 N m, corresponding to a moment magnitude of 8.8, is similar to that obtained by previous seismic and geodetic inversions.

Monitoring Ground Deformation at the Aquistore CO2 Storage Site in SE Saskatchewan, Canada

NASA Astrophysics Data System (ADS)

Samsonov, S. V.; White, D.; Craymer, M. R.; Murnaghan, K.; Chalaturnyk, R. J.

2012-12-01

The scientific objectives of the Aquistore CO2 storage project is to design, adapt, and test non-seismic monitoring methods that have not been systematically utilized to date for monitoring CO2 storage, and to integrate the data from these various monitoring tools to obtain quantitative estimates of the change in subsurface fluid distributions, pressure changes and associated surface deformation. For this an array of monitoring methodologies will be tested, including satellite-, surface- and wellbore-based monitoring systems. Interferometric Synthetic Aperture Radar (InSAR), GPS and tiltmeter monitoring will be used for measuring any ground deformation caused by CO2 injection and the associated subsurface pressure perturbation. In the spring-summer of 2012 we started collecting C-band SAR data from the Canadian Radarsat-2 satellite to provide baseline data over the study site. The Radarsat-2 data is acquired about every six days on average in five different geometries in order to achieve nearly uninterrupted coverage. We acquire ascending and descending spotlight data with sub-meter resolution (1.6x0.8 m), ascending and descending wide ultra fine data with moderate resolution (1.6x2.8 m) and descending fine quad-pol data with coarse resolution (5.2x7.6 m). Over the project life, this SAR coverage will be supplemented by X-band TerraSAR-X data, C-band Sentinel, and L-band ALOS-2 data. Availability of SAR data from all three wave-band sensors should allow us to measure ground deformation with a precision of a few mm/year. For mitigating temporal de-correlation and for improving precision during the winter when there will be snow cover, we will install 13 paired corner reflectors suitable for ascending and descending imaging. Multidimensional time series of ground deformation will be produced using MSBAS techniques (Samsonov and d'Oreye, 2012). PolInSAR methodology will be tested on fine quad-pol data. To obtain higher precision spatial and higher resolution temporal ground motion measurements we will install 13 continuous Global Positioning Systems (cGPS), and 5-6 tiltmeters in the fall of 2012. Various geodetic data will be integrated using the methodology of Samsonov et al., 2007 and resultant ground deformation maps will be used for validation of the geomechanical modelling. Here we will present maps of the injection site showing the locations and installation design of various geodetic sensors and provide initial results of InSAR measurements.

Seafloor geodesy: Measuring surface deformation and strain-build up

NASA Astrophysics Data System (ADS)

Kopp, Heidrun; Lange, Dietrich; Hannemann, Katrin; Petersen, Florian

2017-04-01

Seafloor deformation is intrinsically related to tectonic processes, which potentially may evolve into geohazards, including earthquakes and tsunamis. The nascent scientific field of seafloor geodesy provides a way to monitor crustal deformation at high resolution comparable to the satellite-based GPS technique upon which terrestrial geodesy is largely based. The measurements extract information on stress and elastic strain stored in the oceanic crust. Horizontal seafloor displacement can be obtained by acoustic/GPS combination to provide absolute positioning or by long-term acoustic telemetry between different beacons fixed on the seafloor. The GeoSEA (Geodetic Earthquake Observatory on the SEAfloor) array uses acoustic telemetry for relative positioning at mm-scale resolution. The transponders within an array intercommunicate via acoustic signals for a period of up to 3.5 years. The seafloor acoustic transponders are mounted on 4 m high tripod steel frames to ensure clear line-of-sight between the stations. The transponders also include high-precision pressure sensors to monitor vertical movements and dual-axis inclinometers in order to measure their level as well as any tilt of the seafloor. Sound velocity sensor measurements are used to correct for water sound speed variations. A further component of the network is GeoSURF, a self-steering autonomous surface vehicle (Wave Glider), which monitors system health and is able to upload the seafloor data to the sea surface and to transfer it via satellite. The GeoSEA array is capable of both continuously monitoring horizontal and vertical ground displacement rates along submarine fault zones and characterizing their behavior (locked or aseismically creeping). Seafloor transponders are currently installed along the Siliviri segment of the North Anatolian Fault offshore Istanbul for measurements of strain build-up along the fault. The first 18 month of baseline ranging were analyzed by a joint-least square inversion and forward modeling for across-fault baseline changes. The initial results of the long-term observation period preclude fault-displacement at rates larger than a few millimeters-per-year, suggesting a locked state for the Istanbul-Siliviri segment, indicating that this portion of the fault is accumulating stress rather than continuously creeping at a slip-rate higher than 10 mm/yr during the observation period. In addition, three arrays are currently deployed on the marine forearc and outer rise of the South American subduction system around 21°S. This segment of the Nazca-South American plate boundary has last ruptured in an earthquake in 1877 and was identified as a seismic gap prior to the 2014 Iquique/Pisagua earthquake (Mw=8.1). The southern portion of the segment remains unbroken by a recent earthquake.

Landslide Monitoring Using Insar Time-Series and GPS Observations, Case Study: Shabkola Landslide in Northern Iran

NASA Astrophysics Data System (ADS)

Mirzaee, S.; Motagh, M.; Akbari, B.

2017-05-01

Shabkola is a village located in Mazandaran province of northern Iran that suffers from the mass movement happening in the upstream. Deforestation and changes to land use are the main reasons for the soil instability in this region, which together with steep slope, relatively high precipitation rate and natural erosion has led to such a condition. The area of mass movement is approximately 90 hectares which is a big threat for people living in the region. In this study, we have utilized two different geodetic techniques including InSAR time-series analysis and GPS measurements to assess slope stability in Shabkola. The SAR dataset includes 19 ALOS/PALSAR images spanning from July 2007 to February 2011 while GPS observations are collected in 5 campaigns from September 2011 to May 2014. Displacement as much as approximately 11.7 m in slope direction was detected by GPS observations for the 2011-2014 time period. Most of the slope geometry is in north-south direction, for which the sensitivity of InSAR for displacement detection is low. However, ALOS PALSAR data analysis revealed a previously unknown landslide, covered by dense vegetation in the northern part of main Shabkola landslide, showing line-of-sight velocity of approximately 2cm/year in the time period 2007-2011.

GPS deformation rates in the Bajo Segura Basin (NE of the Eastern Betic Shear Zone, SE Spain)

NASA Astrophysics Data System (ADS)

Jesús Borque, María; Sánchez-Alzola, Alberto; Estévez, Antonio; García-Tortosa, Francisco J.; Martín-Rojas, Iván; Molina, Sergio; Alfaro, Pedro; Rodríguez-Caderot, Gracia; de Lacy, Clara; García-Armenteros, Juan Antonio; Avilés, Manuel; Herrera, Antonio; Rosa-Cintas, Sergio; Gil, Antonio J.

2014-05-01

The Bajo Segura Basin, located in the NE end of the Eastern Betic Shear Zone, is one of the areas with highest seismic activity of the Iberian Peninsula. It is bounded by the Crevillente Fault to the north and the Bajo Segura Fault to the south, and it is characterized by a Late Miocene to Quaternary folded cover. We estimate the present-day deformation of the study area from a GPS network with 11 sites. Observation campaigns were carried out four times (June 1999, September 2001, September 2002 and September 2013). We used the 6.2 version of GIPSY-OASIS software to process GPS data in Precise Point Positioning mode (PPP). In order to obtain the position time series in the whole period of these episodic campaigns, all the GPS observations from 1999 to 2013 campaigns were processed with an identical standard procedure. We compared our velocity field estimation with respect to GEODVEL tectonic model to obtain the residual velocity field of the Bajo Segura Basin. We estimated a ~N-S shortening with deformation rates varying between 0.2 and 0.6 mm/yr. These results are consistent with local geological deformation rates although slightly higher. They also fit well with regional geodetic data estimated for the Western Mediterranean.

Glacial isostatic crustal uplift in southern Victoria Land, Antarctica, from geologic and geodetic records

NASA Astrophysics Data System (ADS)

Konfal, S.; Wilson, T.; Bevis, M. G.; Kendrick, E. C.; Hall, B. L.

2011-12-01

Geologic records and geodetic measurements of glacial isostatic crustal motions are presented from the southern Victoria Land region of Antarctica. In much of the world, key records used for mapping and modeling glacial isostatic crustal motions come from raised paleoshorelines and beaches of ice-marginal lakes and seas. While such records are scarce in Antarctica, preserved paleoshorelines are present in the southern Victoria Land region of Antarctica. Light detection and ranging (LiDAR) data coverages of these features were acquired during the 2001-2002 austral summer field season by NASA's Airborne Topographic Mapper (ATM) system, resulting in 2 meter horizontal resolution digital elevation models (DEMs). This study utilizes these DEM data to derive crustal tilt values from observed changes in elevation along the length of the shorelines. Radiocarbon age data are correlated with the associated degree of shoreline tilt to derive a rate of crustal deformation since deglaciation. Modern rates of glacial isostatic crustal motion are derived from GPS stations in the same region. Campaign station occupation began in 1996-1997 under the TAMDEF (Transantarctic Mountain DEFormation Network) project, and continuous GPS data collected began in 1999 and continues under the ANET/POLENET (Antarctica Polar Earth Observing Network) project, enabling analysis of decadal scale time series. Integrated gradient curves from paleoshoreline records and GPS crustal velocities show exponential form and indicate tilting down to the east. Eastward tilt may be the result of substantial loss of East Antarctic ice, a collapsing forebulge linked to ice centers in the Ross Sea region or in interior West Antarctica, or differences in earth response due to laterally varying earth structure. Modeling of these new data, along with comparison of tilt directions to centers of ice mass loss, provide tests of these scenarios and yield new insights into earth models and ice history.

Rotation of the Pacific Northwest and Deformation Across the Yakima Fold and Thrust Belt Estimated with GPS

NASA Astrophysics Data System (ADS)

McCaffrey, R.; King, R. W.; Lancaster, M.; Miller, M. M.; Wells, R. E.

2015-12-01

Geodetic, geologic and paleomagnetic data reveal that Oregon and parts of California, Nevada and Idaho rotate clockwise at 0.3 to 1.0 deg/Ma (relative to North America) about an axis near the Idaho-Oregon-Washington border, while northeast Washington is relatively fixed to North America. This rotation has been going on for at least 15 Ma. The spatial termination of the rotation requires shortening between Oregon and Washington. The Yakima fold and thrust belt (YFTB) lies along the boundary between northern Oregon and central Washington where convergence of the clockwise-rotating Oregon block is apparently accommodated. Shortening across the YFTB is thought to occur in a fan-like manner, increasing to the west. We obtained high-accuracy, high-density geodetic GPS measurements in 2012 and 2013 that are used with earlier measurements to characterize YFTB kinematics. Deformation associated with the YFTB starts in the south at the Blue Mountains Anticline in northern Oregon and extends northward to Frenchman Hills in Washington. To the east, the faulting and earthquake activity of the YFTB are truncated by a NNW-trending, narrow zone of deformation that runs along the Pasco Basin and Moses Lake region. It accommodates about 0.5 to 1.0 mm/yr of east to northeast shortening along the eastern boundary of the Department of Energy Hanford Site. The deforming zone aligns with recent seismicity in the Ice Harbor dike swarm, a relatively young ~ 8.5 Ma vent complex. West of the Cascade arc, shortening is accommodated by a series of east-trending faults, starting at the Doty fault in central coastal Washington and extending through Seattle up to the Canadian border. South of the Doty fault, other faults may take up some motion but may be too slow to resolve with GPS.

Contemporary deformation in the Yakima fold and thrust belt estimated with GPS

NASA Astrophysics Data System (ADS)

McCaffrey, Robert; King, Robert W.; Wells, Ray E.; Lancaster, Matthew; Miller, M. Meghan

2016-10-01

Geodetic, geologic and palaeomagnetic data reveal that Oregon (western USA) rotates clockwise at 0.3 to 1.0° Ma-1 (relative to North America) about an axis near the Idaho-Oregon-Washington border, while northeast Washington is relatively fixed. This rotation has been going on for at least 15 Ma. The Yakima fold and thrust belt (YFTB) forms the boundary between northern Oregon and central Washington where convergence of the clockwise-rotating Oregon block is apparently accommodated. North-south shortening across the YFTB has been thought to occur in a fan-like manner, increasing in rate to the west. We obtained high-accuracy, high-density geodetic GPS measurements in 2012-2014 that are used with earlier GPS measurements from the 1990s to characterize YFTB kinematics. The new results show that the deformation associated with the YFTB starts at the Blue Mountains Anticline in northern Oregon and extends north beyond the Frenchman Hills in Washington, past the epicentre of the 1872 Mw 7.0 Entiat earthquake to 49°N. The north-south strain rate across the region is 2 to 3 × 10-9 yr-1 between the volcanic arc and the eastern edge of the YFTB (241.0°E); east of there it drops to about 10-9 yr-1. At the eastern boundary of the YFTB, faults and earthquake activity are truncated by a north-trending, narrow zone of deformation that runs along the Pasco Basin and Moses Lake regions near 240.9°E. This zone, abutting the Department of Energy Hanford Nuclear Reservation, accommodates about 0.5 mm yr-1 of east to northeast shortening. A similar zone of N-trending transpression is seen along 239.9°E where there is a change in the strike of the Yakima folds. The modern deformation of the YFTB is about 600 km wide from south to north and internally may be controlled by pre-existing crustal structure.

Global deformation of the Earth, surface mass anomalies, and the geodetic infrastructure required to study these processes

NASA Astrophysics Data System (ADS)

Kusche, J.; Rietbroek, R.; Gunter, B.; Mark-Willem, J.

2008-12-01

Global deformation of the Earth can be linked to loading caused by mass changes in the atmosphere, the ocean and the terrestrial hydrosphere. World-wide geodetic observation systems like GPS, e.g., the global IGS network, can be used to study the global deformation of the Earth directly and, when other effects are properly modeled, provide information regarding the surface loading mass (e.g., to derive geo-center motion estimates). Vice versa, other observing systems that monitor mass change, either through gravitational changes (GRACE) or through a combination of in-situ and modeled quantities (e.g., the atmosphere, ocean or hydrosphere), can provide indirect information on global deformation. In the framework of the German 'Mass transport and mass distribution' program, we estimate surface mass anomalies at spherical harmonic resolution up to degree and order 30 by linking three complementary data sets in a least squares approach. Our estimates include geo-center motion and the thickness of a spatially uniform layer on top of the ocean surface (that is otherwise estimated from surface fluxes, evaporation and precipitation, and river run-off) as a time-series. As with all current Earth observing systems, each dataset has its own limitations and do not realize homogeneous coverage over the globe. To assess the impact that these limitations might have on current and future deformation and loading mass solutions, a sensitivity study was conducted. Simulated real-case and idealized solutions were explored in which the spatial distribution and quality of GPS, GRACE and OBP data sets were varied. The results show that significant improvements, e.g., over the current GRACE monthly gravity fields, in particular at the low degrees, can be achieved when these solutions are combined with present day GPS and OBP products. Our idealized scenarios also provide quantitative implications on how much surface mass change estimates may improve in the future when improved observing systems become available.

Contemporary deformation in the Yakima fold and thrust belt estimated with GPS

USGS Publications Warehouse

McCaffrey, Robert; King, Robert W.; Wells, Ray; Lancaster, Matthew; Miller, M. Meghan

2016-01-01

Geodetic, geologic and palaeomagnetic data reveal that Oregon (western USA) rotates clockwise at 0.3 to 1.0° Ma−1 (relative to North America) about an axis near the Idaho–Oregon–Washington border, while northeast Washington is relatively fixed. This rotation has been going on for at least 15 Ma. The Yakima fold and thrust belt (YFTB) forms the boundary between northern Oregon and central Washington where convergence of the clockwise-rotating Oregon block is apparently accommodated. North–south shortening across the YFTB has been thought to occur in a fan-like manner, increasing in rate to the west. We obtained high-accuracy, high-density geodetic GPS measurements in 2012–2014 that are used with earlier GPS measurements from the 1990s to characterize YFTB kinematics. The new results show that the deformation associated with the YFTB starts at the Blue Mountains Anticline in northern Oregon and extends north beyond the Frenchman Hills in Washington, past the epicentre of the 1872 Mw 7.0 Entiat earthquake to 49°N. The north–south strain rate across the region is 2 to 3 × 10−9 yr−1 between the volcanic arc and the eastern edge of the YFTB (241.0°E); east of there it drops to about 10−9 yr−1. At the eastern boundary of the YFTB, faults and earthquake activity are truncated by a north-trending, narrow zone of deformation that runs along the Pasco Basin and Moses Lake regions near 240.9°E. This zone, abutting the Department of Energy Hanford Nuclear Reservation, accommodates about 0.5 mm yr−1 of east to northeast shortening. A similar zone of N-trending transpression is seen along 239.9°E where there is a change in the strike of the Yakima folds. The modern deformation of the YFTB is about 600 km wide from south to north and internally may be controlled by pre-existing crustal structure.

A new global approach to obtain three-dimensional displacement maps by integrating GPS and DInSAR data

NASA Astrophysics Data System (ADS)

Guglielmino, F.; Nunnari, G.; Puglisi, G.; Spata, A.

2009-04-01

We propose a new technique, based on the elastic theory, to efficiently produce an estimate of three-dimensional surface displacement maps by integrating sparse Global Position System (GPS) measurements of deformations and Differential Interferometric Synthetic Aperture Radar (DInSAR) maps of movements of the Earth's surface. The previous methodologies known in literature, for combining data from GPS and DInSAR surveys, require two steps: the first, in which sparse GPS measurements are interpolated in order to fill in GPS displacements at the DInSAR grid, and the second, to estimate the three-dimensional surface displacement maps by using a suitable optimization technique. One of the advantages of the proposed approach is that both these steps are unified. We propose a linear matrix equation which accounts for both GPS and DInSAR data whose solution provide simultaneously the strain tensor, the displacement field and the rigid body rotation tensor throughout the entire investigated area. The mentioned linear matrix equation is solved by using the Weighted Least Square (WLS) thus assuring both numerical robustness and high computation efficiency. The proposed methodology was tested on both synthetic and experimental data, these last from GPS and DInSAR measurements carried out on Mt. Etna. The goodness of the results has been evaluated by using standard errors. These tests also allow optimising the choice of specific parameters of this algorithm. This "open" structure of the method will allow in the near future to take account of other available data sets, such as additional interferograms, or other geodetic data (e.g. levelling, tilt, etc.), in order to achieve even higher accuracy.

GPS Imaging of Time-Dependent Seasonal Strain in Central California

NASA Astrophysics Data System (ADS)

Kraner, M.; Hammond, W. C.; Kreemer, C.; Borsa, A. A.; Blewitt, G.

2016-12-01

Recently, studies are suggesting that crustal deformation can be time-dependent and nontectonic. Continuous global positioning system (cGPS) measurements are now showing how steady long-term deformation can be influenced by factors such as fluctuations in loading and temperature variations. Here we model the seasonal time-dependent dilatational and shear strain in Central California, specifically surrounding the Parkfield region and try to uncover the sources of these deformation patterns. We use 8 years of cGPS data (2008 - 2016) processed by the Nevada Geodetic Laboratory and carefully select the cGPS stations for our analysis based on the vertical position of cGPS time series during the drought period. In building our strain model, we first detrend the selected station time series using a set of velocities from the robust MIDAS trend estimator. This estimation algorithm is a robust approach that is insensitive to common problems such as step discontinuities, outliers, and seasonality. We use these detrended time series to estimate the median cGPS positions for each month of the 8-year period and filter displacement differences between these monthly median positions using a filtering technique called "GPS Imaging." This technique improves the overall robustness and spatial resolution of the input displacements for the strain model. We then model our dilatational and shear strain field for each month of time series. We also test a variety of a priori constraints, which controls the style of faulting within the strain model. Upon examining our strain maps, we find that a seasonal strain signal exists in Central California. We investigate how this signal compares to thermoelastic, hydrologic, and atmospheric loading models during the 8-year period. We additionally determine whether the drought played a role in influencing the seasonal signal.

The Plate Boundary Observatory Student Field Assistant Program in Southern California

NASA Astrophysics Data System (ADS)

Seider, E. L.

2007-12-01

Each summer, UNAVCO hires students as part of the Plate Boundary Observatory (PBO) Student Field Assistant Program. PBO, the geodetic component of the NSF-funded EarthScope project, involves the reconnaissance, permitting, installation, documentation, and maintenance of 880 permanent GPS stations in five years. During the summer 2007, nine students from around the US and Puerto Rico were hired to assist PBO engineers during the busy summer field season. From June to September, students worked closely with PBO field engineers to install and maintain permanent GPS stations in all regions of PBO, including Alaska. The PBO Student Field Assistant Program provides students with professional hands-on field experience as well as continuing education in the geosciences. It also gives students a glimpse into the increasing technologies available to the science community, the scope of geophysical research utilizing these technologies, and the field techniques necessary to complete this research. Students in the PBO Field Assistant Program are involved in all aspects of GPS support, including in-warehouse preparation and in-field installations and maintenance. Students are taught practical skills such as drilling, wiring, welding, hardware configuration, documentation, and proper field safety procedures needed to construct permanent GPS stations. These real world experiences provide the students with technical and professional skills that are not always available to them in a classroom, and will benefit them greatly in their future studies and careers. The 2007 summer field season in Southern California consisted of over 35 GPS permanent station installations. To date, the Southern California region of PBO has installed over 190 GPS stations. This poster presentation will highlight the experiences gained by the Southern California student field assistants, while supporting PBO- Southern California GPS installations in the Mohave Desert and the Inyo National Forest.

Dynamic strain and rotation ground motions of the 2011 Tohoku earthquake from dense high-rate GPS observations in Taiwan

NASA Astrophysics Data System (ADS)

Huang, B. S.; Rau, R. J.; Lin, C. J.; Kuo, L. C.

2017-12-01

Seismic waves generated by the 2011 Mw 9.0 Tohoku, Japan earthquake were well recorded by continuous GPS in Taiwan. Those GPS were operated in one hertz sampling rate and densely distributed in Taiwan Island. Those continuous GPS observations and the precise point positioning technique provide an opportunity to estimate spatial derivatives from absolute ground motions of this giant teleseismic event. In this study, we process and investigate more than one and half hundred high-rate GPS displacements and its spatial derivatives, thus strain and rotations, to compare to broadband seismic and rotational sensor observations. It is shown that continuous GPS observations are highly consistent with broadband seismic observations during its surface waves across Taiwan Island. Several standard Geodesy and seismic array analysis techniques for spatial gradients have been applied to those continuous GPS time series to determine its dynamic strain and rotation time histories. Results show that those derivate GPS vertical axis ground rotations are consistent to seismic array determined rotations. However, vertical rotation-rate observations from the R1 rotational sensors have low resolutions and could not compared with GPS observations for this special event. For its dese spatial distribution of GPS stations in Taiwan Island, not only wavefield gradient time histories at individual site was obtained but also 2-D spatial ground motion fields were determined in this study also. In this study, we will report the analyzed results of those spatial gradient wavefields of the 2011 Tohoku earthquake across Taiwan Island and discuss its geological implications.

PBO Nucleus Project Summary: The Successful Integration of 209 Existing GPS Sions in the Plate Boundary Observatory

NASA Astrophysics Data System (ADS)

Blume, F.; Miller, M.; Boyce, E.; Borsa, A.; Eriksson, S.

2008-12-01

Tectonic and earthquake research in the US has experienced a quiet revolution over the last decade precipitated by the recognition that slow-motion faulting events can both trigger and be triggered by regular earthquakes. Transient motion has now been found in essentially all tectonic environments, and the detection and analysis of such events is the first-order science target of the EarthScope Project. Because of this and a host of other fundamental tectonics questions that can be answered only with long-duration geodetic time series, the 1100-station EarthScope Plate Boundary Observatory (PBO) network was designed to leverage 445 existing continuous GPS stations whose measurements extend back over a decade. The irreplaceable recording history of these stations will accelerate EarthScope scientific return by providing the highest possible resolution. This resolution will be used to detect and understand transients, to determine the three-dimensional velocity field (particularly vertical motion), and to improve measurement precision by understanding the complex noise sources inherent in GPS. The PBO Nucleus project supports the operation, maintenance and hardware upgrades of a subset of the six western U.S. geodetic networks until they are subsumed by PBO. Uninterrupted data flow from these stations will effectively double the time-series length of PBO over the expected life of EarthScope, and has created, for the first time, a single GPS-based geodetic network in the US. The other existing sites remain in operation under support from non-NSF sources (e.g. the USGS), and EarthScope continues to benefit from their continued operation On the grounds of relevance to EarthScope science goals, geographic distribution and data quality, 209 of the 432 existing stations were selected as the nucleus upon which to build PBO. Conversion of these stations to a PBO-compatible mode of operation was begun under previous funding, and as a result data now flow directly to PBO archives and processing centers while maintenance, operations, and meta-data requirements are continue to be upgraded to PBO standards. At the end of this project all 209 stations have been fully incorporated into PBO, meeting all standards for new PBO construction including data communications and land use permits. Funds for operation of these stations have been included in approved budgets for PBO's Operations and Maintenance phase. The data from these stations serve a much larger audience than just the few people who work to keep them operating. This project is now collecting the data that will be used by the next generation of solid-earth researchers for at least two decades. Educational modules are being developed by a team of researchers, educators, and curriculum development professionals, and are being disseminated through regional and national workshops. An interactive website provides the newest developments in tectonics research to K-16 classrooms. class="ab'>

Major risk from rapid, large-volume landslides in Europe (EU Project RUNOUT)

NASA Astrophysics Data System (ADS)

Kilburn, Christopher R. J.; Pasuto, Alessandro

2003-08-01

Project RUNOUT has investigated methods for reducing the risk from large-volume landslides in Europe, especially those involving rapid rates of emplacement. Using field data from five test sites (Bad Goisern and Köfels in Austria, Tessina and Vajont in Italy, and the Barranco de Tirajana in Gran Canaria, Spain), the studies have developed (1) techniques for applying geomorphological investigations and optical remote sensing to map landslides and their evolution; (2) analytical, numerical, and cellular automata models for the emplacement of sturzstroms and debris flows; (3) a brittle-failure model for forecasting catastrophic slope failure; (4) new strategies for integrating large-area Global Positioning System (GPS) arrays with local geodetic monitoring networks; (5) methods for raising public awareness of landslide hazards; and (6) Geographic Information System (GIS)-based databases for the test areas. The results highlight the importance of multidisciplinary studies of landslide hazards, combining subjects as diverse as geology and geomorphology, remote sensing, geodesy, fluid dynamics, and social profiling. They have also identified key goals for an improved understanding of the physical processes that govern landslide collapse and runout, as well as for designing strategies for raising public awareness of landslide hazards and for implementing appropriate land management policies for reducing landslide risk.

Integrating Remote Sensing Data, Hybrid-Cloud Computing, and Event Notifications for Advanced Rapid Imaging & Analysis (Invited)

NASA Astrophysics Data System (ADS)

Hua, H.; Owen, S. E.; Yun, S.; Lundgren, P.; Fielding, E. J.; Agram, P.; Manipon, G.; Stough, T. M.; Simons, M.; Rosen, P. A.; Wilson, B. D.; Poland, M. P.; Cervelli, P. F.; Cruz, J.

2013-12-01

Space-based geodetic measurement techniques such as Interferometric Synthetic Aperture Radar (InSAR) and Continuous Global Positioning System (CGPS) are now important elements in our toolset for monitoring earthquake-generating faults, volcanic eruptions, hurricane damage, landslides, reservoir subsidence, and other natural and man-made hazards. Geodetic imaging's unique ability to capture surface deformation with high spatial and temporal resolution has revolutionized both earthquake science and volcanology. Continuous monitoring of surface deformation and surface change before, during, and after natural hazards improves decision-making from better forecasts, increased situational awareness, and more informed recovery. However, analyses of InSAR and GPS data sets are currently handcrafted following events and are not generated rapidly and reliably enough for use in operational response to natural disasters. Additionally, the sheer data volumes needed to handle a continuous stream of InSAR data sets also presents a bottleneck. It has been estimated that continuous processing of InSAR coverage of California alone over 3-years would reach PB-scale data volumes. Our Advanced Rapid Imaging and Analysis for Monitoring Hazards (ARIA-MH) science data system enables both science and decision-making communities to monitor areas of interest with derived geodetic data products via seamless data preparation, processing, discovery, and access. We will present our findings on the use of hybrid-cloud computing to improve the timely processing and delivery of geodetic data products, integrating event notifications from USGS to improve the timely processing for response, as well as providing browse results for quick looks with other tools for integrative analysis.

Towards Cloud Processing of GGOS Big Data

NASA Astrophysics Data System (ADS)

Weston, Stuart; Kim, Bumjun; Litchfield, Alan; Gulyaev, Sergei; Hall, Dylan; Chorao, Carlos; Ruthven, Andrew; Davies, Glyn; Lagos, Bruno; Christie, Don

2017-04-01

We report on our initial steps towards development of a cloud-like correlation infrastructure for geodetic Very Long Baseline Interferometry (VLBI), which in its raw format is of the order of 10-100 TB (big data). Data is generated by multiple VLBI radio telescopes, and is then used by for geodetic, geophysical, and astrometric research and operational activities through the International VLBI Service (IVS), as well as for corrections of GPS satellite orbits. Currently IVS data is correlated in several international Correlators (Correlation Centres), which receive data from individual radio telescope stations either in hard drives via regular mail service or via fibre using e-transfer mode. The latter is strongly limited by connectivity of existing correlation centres, which creates bottle necks and slows down the turnover of the data. This becomes critical in many applications - for example, it currently takes 1-2 weeks to generate the dUT1 parameter for corrections of GNSS orbits while less than 1-2 days delay is desirable. We started with a blade server at the AUT campus to emulate a cloud server using Virtual Machines (VMWare). The New Zealand Data Head node is connected to the high speed (100 Gbps) network ring circuit courtesy of the Research and Education Advanced Network New Zealand (REANNZ), with the additional nodes at remote physical sites connected via 10 Gbps fibre. We use real Australian Long Baseline Array (LBA) observational data from 6 radio telescopes in Australia, South Africa and New Zealand (15 baselines) of 1.5 hours in duration making 8 TB to emulate data transfer from remote locations and to provide a meaningful benchmark dataset for correlation. Data was successfully transferred using bespoke UDT network transfer tools and correlated with the speed-up factor of 0.8 using DiFX software correlator. In partnership with the New Zealand office of Catalyst IT Ltd we have moved this environment into Catalyst Cloud and report on the first correlation of a VLBI Dataset in a true cloud environment.

A Teachable Moment in Earth Deformation: An Undergraduate Strain Module Incorporating GPS Measurement of the August 24, 2014 M6.0 South Napa Earthquake

NASA Astrophysics Data System (ADS)

Resor, P. G.; Cronin, V. S.; Hammond, W. C.; Pratt-Sitaula, B.; Olds, S. E.

2014-12-01

The August 24, 2014 M 6.0 South Napa Earthquake was the largest earthquake to occur in the San Francisco Bay Area, home to more than 7 million people, in almost 25 years. The event occurred within an area of dense GPS instrumentation including continuous stations from the EarthScope Plate Boundary Observatory, Bay Area Regional Deformation Network and other networks. Coseismic displacements of up to 3 cm were rapidly estimated within one day after the event, providing a map of Earth shape change at over one hundred stations around the epicenter. The earthquake thus presets as an excellent "teachable moment" to introduce students to basic geoscience concepts, modern geophysical methods, and the state of knowledge in earthquake science. We have developed an example exercise that uses GPS-derived interseismic velocities and coseismic offsets to explore deformation in the vicinity of the earthquake rupture. This exercise builds on the UNAVCO education resource "Infinitesimal Strain Analysis Using GPS Data" (http://www.unavco.org/education/resources/educational-resources/lesson/majors-gps-strain/majors-gps-strain.html), a module designed to introduce undergraduate geoscience majors to concepts of crustal deformation using GPS velocity data. In the module students build their intuition about infinitesimal strain through manipulation of physical models, apply this intuition to interpret maps of GPS velocity vectors, and ultimately calculate the instantaneous deformation rate of triangles on the Earth's surface defined by three GPS sites. The South Napa data sets provide an example with clear societal relevance that can be used to explore the basic concepts of deformation, but may also be extended to explore topics such as strain accumulation, release, and transfer associated with the earthquake cycle. The UNAVCO module could be similarly extended to create additional exercises in response to future events with clear geodetic signals.

Present-Day Strain and Rotation in the Lebanese Restraining Bend of the Dead Sea Fault System Based on Analysis of GPS Velocities

NASA Astrophysics Data System (ADS)

Gomez, F.; Jaafar, R.; Abdallah, C.; Karam, G.

2012-12-01

The Lebanese Restraining Bend (LRB) is a ~200-km-long bend in the central part of the Dead Sea Fault system (DSFS). As with other large restraining bends, this part of the transform is characterized by more complicated structure than other parts. Additionally, results from recent GPS studies have documented slower velocities north of the LRB than are observed along the southern DSFS to the south. In an effort to understand how strain is transferred through the LRB, this study analyzes improved GPS velocities within the central DSFS based on new data and additional stations. Despite relatively modest rates of seismicity, the Dead Sea Fault system (DSFS) has a historically documented record of producing large and devastating earthquakes. Hence, geodetic measurements of crustal deformation may provide key constraints on processes of strain accumulation that may not be evident in instrumentally recorded seismicity. Within the LRB, the transform splays into two prominent strike-slip faults: The through-going Yammouneh fault and the Serghaya fault. The latter appears to terminate in the Anti-Lebanon Mountains. Additionally, some oblique plate motion is accommodated by thrusting along the coast of Lebanon. This study used GPS observations from survey-mode GPS sites, as well as continuous GPS stations in the region. In total, 22 GPS survey sites have been measured in Lebanon between 2002 and 2010, along with GPS data from the adjacent area. Elastic models are used for initial assessment of fault slip rates. Incorporating two major strike-slip faults, as well as an offshore thrust fault, this modeling suggests left-lateral slip rates of 3.8 mm/yr and 1.1 mm/yr for the Yammouneh and Serghaya faults, respectively. The GPS survey network has sufficient density for analyzing velocity gradients in an effort to quantify tectonic strains and rotations. The velocity gradients suggest that differential rotations play a role in accommodating some plate motion.

Comparison of geologically-averaged paleomagnetic and "instantaneous" GPS rotation data in the West-Central Walker Lane

NASA Astrophysics Data System (ADS)

Farner, M. J.; Pluhar, C. J.; Carlson, C. W.

2011-12-01

The Walker Lane belt is a highly tectonically active region of dextral shear in western North America. Situated between the margins of the Sierra Nevada microplate and the Basin and Range extension, it extends northward from the Garlock Fault into portions of Southern Oregon. The Walker Lane is characterized by dextral shear accommodated by strike slip faults and left-stepping normal faults (Unruh et al, 2003). Faulting in the Walker Lane accounts for approximately 25% of the relative motion between the North American and Pacific Plates (Reheis and Dixon 1996). The study spans a region where the Sierra Nevada microplate has shed fault-bounded blocks from its eastern margin into the central Walker Lane during the Neogene. These blocks have behaved somewhat independently of one another and the Sierra Nevada as evidenced by spatially-variable magnitudes of vertical-axis rotation. This blurs the boundary of definition between microplate and fault block. One of the key questions regarding Walker Lane deformation is what is the role of rotation with respect to fault blocks and at what rate(s) does rotation occur. The software package SSPX (Cardozo and Allmendinger 2009) is used to examine previously published geodetic data to derive rotation rates in the west-central Walker Lane. A rate of 1.70° ± 0.24°/Ma is determined for Bridgeport Valley, CA based upon strain inversion of the locally-sparse GPS station data in SSPX. This rate is consistent with paleomagnetically-determined rotation rates for ~9.4 Ma members of the Stanislaus Group around Bridgeport Valley, adjacent to the Mina Deflection (e.g. King et al, 2007 and our data). However there are several shortcomings to using currently available GPS data for this purpose. GPS station spacing in many places does not provide spatial resolution of rotation comparable to the paleomagnetic dataset, which in turn limits our ability to examine small lithospheric fault blocks geodetically. The paleomagnetic data shows rotation variations on the scale of <5 km. Thus, due to GPS station spacing, our strain inversion reveals a spatially-averaged rotation for a larger given area and is not able to detect small lithospheric blocks or groups of blocks with anomalously large rotation rates of 7°/Ma or higher. An alternative hypothesis is that rotation rate is variable with time and that large rotations occurred and have slowed or stopped.

Slip rate of the Húsavík-Flatey Fault, North Iceland, derived from GPS and InSAR Time Series

NASA Astrophysics Data System (ADS)

Metzger, S.; Jonsson, S.

2010-12-01

The Húsavík-Flatey fault is one of mainly two parallel fault zones within the Tjörnes Fracture Zone (TFZ), North Iceland. The TFZ is a transform zone and a 120km-offset between two segments of the Mid-Atlantic Ridge, accommodating the 18.2mm/year spreading motion between the North American and the Eurasian Plate at this latitude (NUVEL 1A). Geodetic research mostly concentrates on a relatively short 20km onshore portion of the Húsavík-Flatey fault, as the rest of the whole transform zone, including the Grímsey lineament to the Northeast, is located offshore. The fact that a coastal town with 2300 inhabitants has been built directly at the fault surface trace increases the importance of studying this area. No major earthquake has occurred in the vicinity of the town since two M6.3 earthquakes took place in 1872. Hence, there is a compelling need to estimate the fault slip rate, slip deficit and finally, the seismic risk to which this town is exposed to, as the interseismic part of the current earthquake cycle may be drawing to a close. We use geodetic data, both continuous GPS and satellite radar interferograms (InSAR) to determine the interseismic deformation field around the on-land portion of the Húsavík-Flatey fault. The continuous GPS stations have been recording data since 2006 or longer at 14 sites within the TFZ. In addition, we use time-series analysis of ERS radar interferograms from 1992 to 2000 to derive interseismic velocities across the fault. We simulate the resulting deformation field with an interseismic back-slip model consisting of planar dislocations in an elastic half space and constrain the associated model parameters using a non-linear optimization approach. It has earlier been estimated that only 40% of the total motion is concentrated on the Húsavík-Flatey fault, while the larger 60% is taken up by the Grímsey lineament. This estimate however, was based on only three continuous GPS stations. Including more GPS data, we find that the partial motion on the Húsavík-Flatey fault is even less, closer to 30% and that the locking depth is relatively shallow. The exact parameter values, however, depend significantly on the modeling assumptions. Still, the results show that if moment has been accumulating on the Húsavík-Flatey fault at the current rate since 1872, then the total accumulated moment corresponds to an earthquake of magnitude just below 7.

A large-aperture low-cost hydrophone array for tracking whales from small boats.

PubMed

Miller, B; Dawson, S

2009-11-01

A passive sonar array designed for tracking diving sperm whales in three dimensions from a single small vessel is presented, and the advantages and limitations of operating this array from a 6 m boat are described. The system consists of four free floating buoys, each with a hydrophone, built-in recorder, and global positioning system receiver (GPS), and one vertical stereo hydrophone array deployed from the boat. Array recordings are post-processed onshore to obtain diving profiles of vocalizing sperm whales. Recordings are synchronized using a GPS timing pulse recorded onto each track. Sensitivity analysis based on hyperbolic localization methods is used to obtain probability distributions for the whale's three-dimensional location for vocalizations received by at least four hydrophones. These localizations are compared to those obtained via isodiachronic sequential bound estimation. Results from deployment of the system around a sperm whale in the Kaikoura Canyon in New Zealand are shown.

A Ground-Based Near Infrared Camera Array System for UAV Auto-Landing in GPS-Denied Environment.

PubMed

Yang, Tao; Li, Guangpo; Li, Jing; Zhang, Yanning; Zhang, Xiaoqiang; Zhang, Zhuoyue; Li, Zhi

2016-08-30

This paper proposes a novel infrared camera array guidance system with capability to track and provide real time position and speed of a fixed-wing Unmanned air vehicle (UAV) during a landing process. The system mainly include three novel parts: (1) Infrared camera array and near infrared laser lamp based cooperative long range optical imaging module; (2) Large scale outdoor camera array calibration module; and (3) Laser marker detection and 3D tracking module. Extensive automatic landing experiments with fixed-wing flight demonstrate that our infrared camera array system has the unique ability to guide the UAV landing safely and accurately in real time. Moreover, the measurement and control distance of our system is more than 1000 m. The experimental results also demonstrate that our system can be used for UAV automatic accurate landing in Global Position System (GPS)-denied environments.

Observing APOD with the AuScope VLBI Array

PubMed Central

Sun, Jing; Cao, Jianfeng

2018-01-01

The possibility to observe satellites with the geodetic Very Long Baseline Interferometry (VLBI) technique is vividly discussed in the geodetic community, particularly with regard to future co-location satellite missions. The Chinese APOD-A nano satellite can be considered as a first prototype—suitable for practical observation tests—combining the techniques Satellite Laser Ranging (SLR), Global Navigation Satellite Systems (GNSS) and VLBI on a single platform in a Low Earth Orbit (LEO). Unfortunately, it has hardly been observed by VLBI, so major studies towards actual frame ties could not be performed. The main reason for the lack of observations was that VLBI observations of satellites are non-standard, and suitable observing strategies were not in place for this mission. This work now presents the first serious attempt to observe the satellite with a VLBI network over multiple passes. We introduce a series of experiments with the AuScope geodetic VLBI array which were carried out in November 2016, and describe all steps integrated in the established process chain: the experiment design and observation planning, the antenna tracking and control scheme, correlation and derivation of baseline-delays, and the data analysis yielding delay residuals on the level of 10 ns. The developed procedure chain can now serve as reference for future experiments, hopefully enabling the global VLBI network to be prepared for the next co-location satellite mission. PMID:29772732

Observing APOD with the AuScope VLBI Array.

PubMed

Hellerschmied, Andreas; McCallum, Lucia; McCallum, Jamie; Sun, Jing; Böhm, Johannes; Cao, Jianfeng

2018-05-16

The possibility to observe satellites with the geodetic Very Long Baseline Interferometry (VLBI) technique is vividly discussed in the geodetic community, particularly with regard to future co-location satellite missions. The Chinese APOD-A nano satellite can be considered as a first prototype-suitable for practical observation tests-combining the techniques Satellite Laser Ranging (SLR), Global Navigation Satellite Systems (GNSS) and VLBI on a single platform in a Low Earth Orbit (LEO). Unfortunately, it has hardly been observed by VLBI, so major studies towards actual frame ties could not be performed. The main reason for the lack of observations was that VLBI observations of satellites are non-standard, and suitable observing strategies were not in place for this mission. This work now presents the first serious attempt to observe the satellite with a VLBI network over multiple passes. We introduce a series of experiments with the AuScope geodetic VLBI array which were carried out in November 2016, and describe all steps integrated in the established process chain: the experiment design and observation planning, the antenna tracking and control scheme, correlation and derivation of baseline-delays, and the data analysis yielding delay residuals on the level of 10 ns. The developed procedure chain can now serve as reference for future experiments, hopefully enabling the global VLBI network to be prepared for the next co-location satellite mission.

Laboratory volcano geodesy

NASA Astrophysics Data System (ADS)

Færøvik Johannessen, Rikke; Galland, Olivier; Mair, Karen

2014-05-01

Magma transport in volcanic plumbing systems induces surface deformation, which can be monitored by geodetic techniques, such as GPS and InSAR. These geodetic signals are commonly analyzed through geodetic models in order to constrain the shape of, and the pressure in, magma plumbing systems. These models, however, suffer critical limitations: (1) the modelled magma conduit shapes cannot be compared with the real conduits, so the geodetic models cannot be tested nor validated; (2) the modelled conduits only exhibit shapes that are too simplistic; (3) most geodetic models only account for elasticity of the host rock, whereas substantial plastic deformation is known to occur. To overcome these limitations, one needs to use a physical system, in which (1) both surface deformation and the shape of, and pressure in, the underlying conduit are known, and (2) the mechanical properties of the host material are controlled and well known. In this contribution, we present novel quantitative laboratory results of shallow magma emplacement. Fine-grained silica flour represents the brittle crust, and low viscosity vegetable oil is an analogue for the magma. The melting temperature of the oil is 31°C; the oil solidifies in the models after the end of the experiments. At the time of injection the oil temperature is 50°C. The oil is pumped from a reservoir using a volumetric pump into the silica flour through a circular inlet at the bottom of a 40x40 cm square box. The silica flour is cohesive, such that oil intrudes it by fracturing it, and produces typical sheet intrusions (dykes, cone sheets, etc.). During oil intrusion, the model surface deforms, mostly by doming. These movements are measured by an advanced photogrammetry method, which uses 4 synchronized fixed cameras that periodically image the surface of the model from different angles. We apply particle tracking method to compute the 3D ground deformation pattern through time. After solidification of the oil, the intrusion can be excavated and photographed from several angles to compute its 3D shape with the same photogrammetry method. Then, the surface deformation pattern can be directly compared with the shape of underlying intrusion. This quantitative dataset is essential to quantitatively test and validate classical volcano geodetic models.

NASA's Contribution to Global Space Geodesy Networks

NASA Technical Reports Server (NTRS)

Bosworth, John M.

1999-01-01

The NASA Space Geodesy program continues to be a major provider of space geodetic data for the international earth science community. NASA operates high performance Satellite Laser Ranging (SLR), Very Long Baseline Interferometry (VLBI) and Global Positioning System (GPS) ground receivers at well over 30 locations around the world and works in close cooperation with space geodetic observatories around the world. NASA has also always been at the forefront in the quest for technical improvement and innovation in the space geodesy technologies to make them even more productive, accurate and economical. This presentation will highlight the current status of NASA's networks; the plans for partnerships with international groups in the southern hemisphere to improve the geographic distribution of space geodesy sites and the status of the technological improvements in SLR and VLBI that will support the new scientific thrusts proposed by interdisciplinary earth scientists. In addition, the expanding role of the NASA Space geodesy data archive, the CDDIS will be described.

Seismic and aseismic slip on the ``uncoupled'' Tonga subduction megathrust

NASA Astrophysics Data System (ADS)

Beavan, R. J.; Wang, X.; Bevis, M. G.; Kautoke, R'

2010-12-01

The Tonga subduction zone has been a type example of a weakly coupled subduction interface since soon after the birth of plate tectonics. Yet in the September 2009 double earthquake, the northern Tonga subduction interface failed in a great Mw 8 earthquake that was probably dynamically triggered by a Mw 8 extensional intraplate earthquake in the outer trench slope region of the incoming Pacific Plate. There are some discrepancies between models of the September 2009 doublet derived from seismic data and those derived from geodetic and DART tsunami data, in particular about which fault plane failed in the intraplate earthquake. In this presentation we explore how well the geodetic and tsunami data can be fit using the alternative fault plane. We also present new GPS data that show the subduction interface is continuing to slip faster than its 1996-2005 “long-term” rate, and we speculate on what this means for the mechanisms by which interplate slip is accommodated at the Tonga subduction zone.

Kinematics and mechanics of tectonic block rotations

NASA Technical Reports Server (NTRS)

Nur, Amos; Scotti, Oona; Ron, Hagai

1989-01-01

Paleomagnetic, structural geology, and rock mechanics data are combined to explore the validity of the block rotation concept and its significance. The analysis is based on data from (1) Northern Israel, where fault slip and spacing are used to predict block rotation; (2) the Mojave Desert, with well-documented strike-slip fault sets, organized in at least three major domains; (3) the Lake Mead, Nevada, fault system with well-defined sets of strike-slip faults, which, in contrast to the Mojave region, are surrounded with domains of normal faults; and (4) the San Gabriel Mountains domain with a multiple set of strike-slip faults. It is found that block rotations can have a profound influence on the interpretation of geodetic measurements and the inversion of geodetic data, especially the type collected in GPS surveys. Furthermore, block rotations and domain boundaries may be involved in creating the heterogeneities along active fault systems which are responsible for the initiation and termination of earthquake rupture.

VLBI and GPS-based Time-Transfer Using CONT08 Data

NASA Technical Reports Server (NTRS)

Rieck, Carsten; Haas, Ruediger; Jaldehag, Kenneth; Jahansson, Jan

2010-01-01

One important prerequisite for geodetic Very Long Baseline Interferometry (VLBI) is the use of frequency standards with excellent short term stability. This makes VLBI stations, which are often co-located with Global Navigation Satellite System (GNSS) receiving stations, interesting for studies of time- and frequency-transfer techniques. We present an assessment of VLBI time-transfer based on the data of the two week long consecutive IVS CONT08 VLBI campaign by using GPS Carrier Phase (GPSCP). CONT08 was a 15 day long campaign in August 2008 that involved eleven VLBI stations on five continents. For CONT08 we estimated the worst case VLBI frequency link stability between the stations of Onsala and Wettzell to 1e-15 at one day. Comparisons with GPSCP confirm the VLBI results. We also identify time-transfer related challenges of the VLBI technique as used today.

Quality Test Various Existing dem in Indonesia Toward 10 Meter National dem

NASA Astrophysics Data System (ADS)

Amhar, Fahmi

2016-06-01

Indonesia has various DEM from many sources and various acquisition date spreaded in the past two decades. There are DEM from spaceborne system (Radarsat, TerraSAR-X, ALOS, ASTER-GDEM, SRTM), airborne system (IFSAR, Lidar, aerial photos) and also terrestrial one. The research objective is the quality test and how to extract best DEM in particular area. The method is using differential GPS levelling using geodetic GPS equipment on places which is ensured not changed during past 20 years. The result has shown that DEM from TerraSAR-X and SRTM30 have the best quality (rmse 3.1 m and 3.5 m respectively). Based on this research, it was inferred that these parameters are still positively correlated with the basic concept, namely that the lower and the higher the spatial resolution of a DEM data, the more imprecise the resulting vertical height.

CASA Uno GPS orbit and baseline experiments

NASA Technical Reports Server (NTRS)

Schutz, B. E.; Ho, C. S.; Abusali, P. A. M.; Tapley, B. D.

1990-01-01

CASA Uno data from sites distributed in longitude from Australia to Europe have been used to determine orbits of the GPS satellites. The characteristics of the orbits determined from double difference phase have been evaluated through comparisons of two-week solutions with one-week solutions and by comparisons of predicted and estimated orbits. Evidence of unmodeled effects is demonstrated, particularly associated with the orbit planes that experience solar eclipse. The orbit accuracy has been assessed through the repeatability of unconstrained estimated baseline vectors ranging from 245 km to 5400 km. Both the baseline repeatability and the comparison with independent space geodetic methods give results at the level of 1-2 parts in 100,000,000. In addition, the Mojave/Owens Valley (245 km) and Kokee Park/Ft. Davis (5409 km) estimates agree with VLBI and SLR to better than 1 part in 100,000,000.

Slip pulse and resonance of Kathmandu basin during the 2015 Mw 7.8 Gorkha earthquake, Nepal imaged with space geodesy

USGS Publications Warehouse

Galetzka, John; Melgar, D.; Genrich, J.F.; Geng, J.; Owen, S.; Lindsey, E. O.; Xu, X.; Bock, Y.; Avouac, J.-P.; Adhikari, L. B.; Upreti, B. N.; Pratt-Sitaula, B.; Bhattarai, T. N.; Sitaula, B. P.; Moore, A.; Hudnut, Kenneth W.; Szeliga, W.; Normandeau, J.; Fend, M.; Flouzat, M; Bollinger, L.; Shrestha, P.; Koirala, B.; Gautam, U.; Bhatterai, M.; Gupta, R.; Kandel, T.; Timsina, C.; Sapkota, S.N.; Rajaure, S.; Maharjan, N.

2015-01-01

Detailed geodetic imaging of earthquake rupture enhances our understanding of earthquake physics and induced ground shaking. The April 25, 2015 Mw 7.8 Gorkha, Nepal earthquake is the first example of a large continental megathrust rupture beneath a high-rate (5 Hz) GPS network. We use GPS and InSAR data to model the earthquake rupture as a slip pulse of ~20 km width, ~6 s duration, and with peak sliding velocity of 1.1 m/s that propagated toward Kathmandu basin at ~3.3 km/s over ~140 km. The smooth slip onset, indicating a large ~5 m slip-weakening distance, caused moderate ground shaking at high >1Hz frequencies (~16% g) and limited damage to regular dwellings. Whole basin resonance at 4-5 s period caused collapse of tall structures, including cultural artifacts.

Temporal–Spatial Surface Seasonal Mass Changes and Vertical Crustal Deformation in South China Block from GPS and GRACE Measurements

PubMed Central

He, Meilin; Shen, Wenbin; Chen, Ruizhi; Ding, Hao; Guo, Guangyi

2017-01-01

The solid Earth deforms elastically in response to variations of surface atmosphere, hydrology, and ice/glacier mass loads. Continuous geodetic observations by Global Positioning System (CGPS) stations and Gravity Recovery and Climate Experiment (GRACE) record such deformations to estimate seasonal and secular mass changes. In this paper, we present the seasonal variation of the surface mass changes and the crustal vertical deformation in the South China Block (SCB) identified by GPS and GRACE observations with records spanning from 1999 to 2016. We used 33 CGPS stations to construct a time series of coordinate changes, which are decomposed by empirical orthogonal functions (EOFs) in SCB. The average weighted root-mean-square (WRMS) reduction is 38% when we subtract GRACE-modeled vertical displacements from GPS time series. The first common mode shows clear seasonal changes, indicating seasonal surface mass re-distribution in and around the South China Block. The correlation between GRACE and GPS time series is analyzed which provides a reference for further improvement of the seasonal variation of CGPS time series. The results of the GRACE observations inversion are the surface deformations caused by the surface mass change load at a rate of about −0.4 to −0.8 mm/year, which is used to improve the long-term trend of non-tectonic loads of the GPS vertical velocity field to further explain the crustal tectonic movement in the SCB and surroundings. PMID:29301236

The 2014 Mw 6.0 Napa Earthquake, California: Observations from Real-time GPS-enhanced Earthquake Early Warning

NASA Astrophysics Data System (ADS)

Johanson, I. A.; Grapenthin, R.; Allen, R. M.

2014-12-01

Recently, progress has been made to demonstrate feasibility and benefits of including real-time GPS (rtGPS) in earthquake early warning and rapid response systems. While most concepts have yet to be integrated into operational environments, the Berkeley Seismological Laboratory is currently running an rtGPS based finite fault inversion scheme in true real-time, which is triggered by the seismic-based ShakeAlert system and then sends updated earthquake alerts to a test receiver. The Geodetic Alarm System (G-larmS) was online and responded to the 2014 Mw6.0 South Napa earthquake in California. We review G-larmS' performance during this event and for 13 aftershocks, and we present rtGPS observations and real-time modeling results for the main shock. The first distributed slip model and a magnitude estimate of Mw5.5 were available 24 s after the event origin time, which could be reduced to 14 s after a bug fix (~8 s S-wave travel time, ~6 s data latency). The system continued to re-estimate the magnitude once every second: it increased to Mw5.9 3 s after the first alert and stabilized at Mw5.8 after 15 s. G-larmS' solutions for the subsequent small magnitude aftershocks demonstrate that Mw~6.0 is the current limit for alert updates to contribute back to the seismic-based early warning system.

Strain accumulation in the Shumagin Islands: Results of initial GPS measurements

USGS Publications Warehouse

Larson, Kristine M.; Lisowski, Michael

1994-01-01

Deformation in the Shumagin seismic gap has been monitored with repeated trilateration (EDM) in the 1980–1987 interval and with the Global Positioning System (GPS) in the 1987–1991 interval. The geodetic network extends for 100-km across the Shumagin Islands to the Alaska Peninsula. Results from the GPS surveys are consistent with those previously reported for the EDM surveys: we failed to detect significant strain accumulation in the N30°W direction of plate convergence. Using the method of simultaneous reduction for position and strain rates, we found the average rate of extension in the direction of plate convergence to be −25±25 nanostrain/yr (nstrain/yr) during the 1987–1991 interval of GPS surveys compared with −20±15 nstrain/yr during the 1981–1987 interval of complete EDM surveys. We found a marginally significant −26±12 nstrain/yr extension rate in the 1981–1991 interval covered by the combined EDM and GPS surveys. Strain rates are higher, but not significantly so, in the part of the network closest to the trench. Spatial variation in the deformation is observed in the 1980–1991 average station velocities, where three of the four stations closest to the trench have an arcward velocity of a few mm/yr. The observed strain rates are an order of magnitude lower than the −200 nstrain/yr rate predicted by dislocation models.

Comparison of observation level versus 24-hour average atmospheric loading corrections in VLBI analysis

NASA Astrophysics Data System (ADS)

MacMillan, D. S.; van Dam, T. M.

2009-04-01

Variations in the horizontal distribution of atmospheric mass induce displacements of the Earth's surface. Theoretical estimates of the amplitude of the surface displacement indicate that the predicted surface displacement is often large enough to be detected by current geodetic techniques. In fact, the effects of atmospheric pressure loading have been detected in Global Positioning System (GPS) coordinate time series [van Dam et al., 1994; Dong et al., 2002; Scherneck et al., 2003; Zerbini et al., 2004] and very long baseline interferometery (VLBI) coordinates [Rabble and Schuh, 1986; Manabe et al., 1991; van Dam and Herring, 1994; Schuh et al., 2003; MacMillan and Gipson, 1994; and Petrov and Boy, 2004]. Some of these studies applied the atmospheric displacement at the observation level and in other studies, the predicted atmospheric and observed geodetic surface displacements have been averaged over 24 hours. A direct comparison of observation level and 24 hour corrections has not been carried out for VLBI to determine if one or the other approach is superior. In this presentation, we address the following questions: 1) Is it better to correct geodetic data at the observation level rather than applying corrections averaged over 24 hours to estimated geodetic coordinates a posteriori? 2) At the sub-daily periods, the atmospheric mass signal is composed of two components: a tidal component and a non-tidal component. If observation level corrections reduce the scatter of VLBI data more than a posteriori correction, is it sufficient to only model the atmospheric tides or must the entire atmospheric load signal be incorporated into the corrections? 3) When solutions from different geodetic techniques (or analysis centers within a technique) are combined (e.g., for ITRF2008), not all solutions may have applied atmospheric loading corrections. Are any systematic effects on the estimated TRF introduced when atmospheric loading is applied?

The kinematics of crustal deformation in Java from GPS observations: Implications for fault slip partitioning

NASA Astrophysics Data System (ADS)

Koulali, A.; McClusky, S.; Susilo, S.; Leonard, Y.; Cummins, P.; Tregoning, P.; Meilano, I.; Efendi, J.; Wijanarto, A. B.

2017-01-01

Our understanding of seismic risk in Java has been focused primarily on the subduction zone, where the seismic records during the last century have shown the occurrence of a number of tsunami earthquakes. However, the potential of the existence of active crustal structures within the island of Java itself is less well known. Historical archives show the occurrence of several devastating earthquake ruptures north of the volcanic arc in west Java during the 18th and the 19th centuries, suggesting the existence of active faults that need to be identified in order to guide seismic hazard assessment. Here we use geodetic constraints from the Global Positioning System (GPS) to quantify the present day crustal deformation in Java. The GPS velocities reveal a homogeneous counterclockwise rotation of the Java Block independent of Sunda Block, consistent with a NE-SW convergence between the Australian Plate and southeast Asia. Continuous GPS observations show a time-dependent change in the linear rate of surface motion in west Java, which we interpret as an ongoing long-term post-seismic deformation following the 2006 Mw 7.7 Java earthquake. We use an elastic block model in combination with a viscoelastic model to correct for this post-seismic transient and derive the long-term inter-seismic velocity, which we interpret as a combination of tectonic block motions and crustal faults strain related deformation. There is a north-south gradient in the resulting velocity field with a decrease in the magnitude towards the North across the Kendeng Thrust in the east and the Baribis Thrust in the west. We suggest that the Baribis Thrust is active and accommodating a slow relative motion between Java and the Sunda Block at about 5 ± 0.2 mm /yr. We propose a kinematic model of convergence of the Australian Plate and the Sunda Block, involving a slip partitioning between the Java Trench and a left-lateral structure extending E-W along Java with most of the convergence being accommodated by the Java megathrust, and a much smaller parallel motion accommodated along the Baribis (∼ 5 ± 0.2 mm /yr) and Kendeng (∼ 2.3 ± 0.7 mm /yr) Thrusts. Our study highlights a correlation between the geodetically inferred active faults and historical seismic catalogs, emphasizing the importance of considering crustal fault activity within Java in future seismic assessments.

Kinematics of the Southwestern Caribbean from New Geodetic Observations

NASA Astrophysics Data System (ADS)

Ruiz, G.; La Femina, P. C.; Tapia, A.; Camacho, E.; Chichaco, E.; Mora-Paez, H.; Geirsson, H.

2014-12-01

The interaction of the Caribbean, Cocos, Nazca, and South American plates has resulted in a complex plate boundary zone and the formation of second order tectonic blocks (e.g., the North Andean, Choco and Central America Fore Arc blocks). The Panama Region [PR], which is bounded by these plates and blocks, has been interpreted and modeled as a single tectonic block or deformed plate boundary. Previous research has defined the main boundaries: 1) The Caribbean plate subducts beneath the isthmus along the North Panama Deformed Belt, 2) The Nazca plate converges at very high obliquity with the PR and motion is assumed along a left lateral transform fault and the South Panama Deformed Belt, 3) The collision of PR with NW South America (i.e., the N. Andean and Choco blocks) has resulted in the Eastern Panama Deformed Belt, and 4) collision of the Cocos Ridge in the west is accommodated by crustal shortening, Central American Fore Arc translation and deformation across the Central Costa Rican Deformed Belt. In addition, there are several models that suggest internal deformation of this region by cross-isthmus strike-slip faults. Recent GPS observations for the PR indicates movement to the northeast relative to a stable Caribbean plate at rates of 6.9±4.0 - 7.8±4.8 mm a-1 from southern Costa Rica to eastern Panama, respectively (Kobayashi et al., 2014 and references therein). However, the GPS network did not have enough spatial density to estimate elastic strain accumulation across these faults. Recent installation and expansion of geodetic networks in southwestern Caribbean (i.e., Costa Rica, Panama, and Colombia) combined with geological and geophysical observations provide a new input to investigate crustal deformation processes in this complex tectonic setting, specifically related to the PR. We use new and existing GPS data to calculate a new velocity field for the region and to investigate the kinematics of the PR, including elastic strain accumulation on the major plate boundaries. Expanding our GPS observations within these proposed small blocks could allow us to solve for Euler vectors and calculate their rotation, strain accumulation and slip rates on the major fault systems. Our results combined with the local seismicity could help authorities to reduce uncertainties in seismic risk evaluations.

Constraints on fault slip rates of the southern California plate boundary from GPS velocity and stress inversions

USGS Publications Warehouse

Becker, T.W.; Hardebeck, J.L.; Anderson, G.

2005-01-01

We use Global Positioning System (GPS) velocities and stress orientations inferred from seismicity to invert for the distribution of slip on faults in the southern California plate-boundary region. Of particular interest is how long-term slip rates are partitioned between the Indio segment of the San Andreas fault (SAF), the San Jacinto fault (SJF) and the San Bernardino segment of the SAE We use two new sets of constraints to address this problem. The first is geodetic velocities from the Southern California Earthquake Center's (SCEC) Crustal Motion Map (version 3 by Shen et al.), which includes significantly more data than previous models. The second is a regional model of stress-field orientations at seismogenic depths, as determined from earthquake focal mechanisms. While GPS data have been used in similar studies before, this is the first application of stress-field observations to this problem. We construct a simplified model of the southern California fault system, and estimate the interseismic surface velocities using a backslip approach with purely elastic strain accumulation, following Meade et al. In addition, we model the stress orientations at seismogenic depths, assuming that crustal stress results from the loading of active faults. The geodetically derived stressing rates are found to be aligned with the stress orientations from seismicity. We therefore proceed to invert simultaneously GPS and stress observations for slip rates of the faults in our network. We find that the regional patterns of crustal deformation as imaged by both data sets can be explained by our model, and that joint inversions lead to better constrained slip rates. In our preferred model, the SJF accommodates ???15 mm yr-1 and the Indio segment of the SAF ???23 mm yr-1 of right-lateral motion, accompanied by a low slip rate on the San Bernardino segment of the SAF 'Anomalous' fault segments such as around the 1992 Mw = 7.3 Landers surface rupture can be detected. There, observed stresses deviate strongly from the long-term loading as predicted by our simple model. Evaluation of model misfits together with information from palaeoseismology may provide further insights into the time dependence of strain accumulation along the San Andreas system. ?? 2004 RAS.

4-D Visualization of Seismic and Geodetic Data of the Big Island of Hawai'i

NASA Astrophysics Data System (ADS)

Burstein, J. A.; Smith-Konter, B. R.; Aryal, A.

2017-12-01

For decades Hawai'i has served as a natural laboratory for studying complex interactions between magmatic and seismic processes. Investigating characteristics of these processes, as well as the crustal response to major Hawaiian earthquakes, requires a synthesis of seismic and geodetic data and models. Here, we present a 4-D visualization of the Big Island of Hawai'i that investigates geospatial and temporal relationships of seismicity, seismic velocity structure, and GPS crustal motions to known volcanic and seismically active features. Using the QPS Fledermaus visualization package, we compile 90 m resolution topographic data from NASA's Shuttle Radar Topography Mission (SRTM) and 50 m resolution bathymetric data from the Hawaiian Mapping Research Group (HMRG) with a high-precision earthquake catalog of more than 130,000 events from 1992-2009 [Matoza et al., 2013] and a 3-D seismic velocity model of Hawai'i [Lin et al., 2014] based on seismic data from the Hawaiian Volcano Observatory (HVO). Long-term crustal motion vectors are integrated into the visualization from HVO GPS time-series data. These interactive data sets reveal well-defined seismic structure near the summit areas of Mauna Loa and Kilauea volcanoes, where high Vp and high Vp/Vs anomalies at 5-12 km depth, as well as clusters of low magnitude (M < 3.5) seismicity, are observed. These areas of high Vp and high Vp/Vs are interpreted as mafic dike complexes and the surrounding seismic clusters are associated with shallow magma processes. GPS data are also used to help identify seismic clusters associated with the steady crustal detachment of the south flank of Kilauea's East Rift Zone. We also investigate the fault geometry of the 2006 M6.7 Kiholo Bay earthquake event by analyzing elastic dislocation deformation modeling results [Okada, 1985] and HVO GPS and seismic data of this event. We demonstrate the 3-D fault mechanisms of the Kiholo Bay main shock as a combination of strike-slip and dip-slip components (net slip 0.55 m) delineating a 30 km east-west striking, southward-dipping fault plane, occurring at 39 km depth. This visualization serves as a resource for advancing scientific analyses of Hawaiian seismic processes, as well as an interactive educational tool for demonstrating the geospatial and geophysical structure of the Big Island of Hawai'i.

Crustal strain accumulation on Southern Basin and Range Province faults modulated by distant plate boundary earthquakes? Evidence from geodesy, seismic imaging, and paleoseismology

NASA Astrophysics Data System (ADS)

Bennett, R. A.; Shirzaei, M.; Broermann, J.; Spinler, J. C.; Holland, A. A.; Pearthree, P.

2014-12-01

GPS in Arizona reveals a change in the pattern of crustal strain accumulation in 2010 and based on viscoelastic modeling appears to be associated with the distant M7.2 El Mayor-Cucapah (EMC) earthquake in Baja California, Mexico. GPS data collected between 1999 and 2009 near the Santa Rita normal fault in SE Arizona reveal a narrow zone of crustal deformation coincident with the fault trace, delineated by W-NW facing Pleistocene fault scarps of heights 1 to 7 m. The apparent deformation zone is also seen in a preliminary InSAR interferogram. Total motion across the zone inferred using an elastic block model constrained by the pre-2010 GPS measurements is ~1 mm/yr in a sense consistent with normal fault motion. However, continuous GPS measurements throughout Arizona reveal pronounced changes in crustal velocity following the EMC earthquake, such that the relative motion across the Santa Rita fault post-2010 is negligible. Paleoseismic evidence indicates that mapped Santa Rita fault scarps were formed by two or more large magnitude (M6.7 to M7.6) surface rupturing normal-faulting earthquakes 60 to 100 kyrs ago. Seismic refraction and reflection data constrained by deep (~800 m) well log data provide evidence of progressive, possibly intermittent, displacement on the fault through time. The rate of strain accumulation observed geodetically prior to 2010, if constant over the past 60 to 100 kyrs, would imply an untenable minimum slip rate deficit of 60 to 100 m since the most recent earthquake. One explanation for the available geodetic, seismic, and paleoseismic evidence is that strain accumulation is modulated by viscoelastic relaxation associated with frequent large magnitude earthquakes in the Salton Trough region, episodically inhibiting the accumulation of elastic strain required to generate large earthquakes on the Santa Rita and possibly other faults in the Southern Basin and Range. An important question is thus for how long the postseismic velocity changes will persist relative to the recurrence interval of large Salton Trough earthquakes. Understanding the influence of far-field postseismic deformation on the southern Arizona strain rate field could have implications for other regions of diffuse intracontinental deformation in proximity to frequently rupturing large magnitude plate boundary faults.

Integration Of Low-Cost Single-Frequency GPS Stations Using 'Spider' Technology Within Existing Dual-Frequency GPS Network at Soufrière Hills Volcano, Montserrat (West Indies): Processing And Results

NASA Astrophysics Data System (ADS)

Pascal, K.; Palamartchouk, K.; Lahusen, R. G.; Young, K.; Voight, B.

2015-12-01

Twenty years ago, began the eruption of the explosive Soufrière Hills Volcano, dominating the southern part of the island of Montserrat, West Indies. Five phases of effusive activity have now occurred, characterized by dome building and collapse, causing numerous evacuations and the emigration of half of the population. Over the years, the volcano monitoring network has greatly expanded. The GPS network, started from few geodetic markers, now consists of 14 continuous dual frequency GPS stations, distributed on and around the edifice, where topography and vegetation allow. The continuous GPS time series have given invaluable insight into the volcano behavior, notably revealing deflation/inflation cycles corresponding to phases and pauses of effusive activity, respectively. In 2014, collaboration of the CALIPSO Project (Penn State; NSF) with the Montserrat Volcano Observatory enriched the GPS and seismic monitoring networks with six 'spider' stations. The 'spiders', developed by R. Lahusen at Cascades Volcano Observatory, are designed to be deployed easily in rough areas and combine a low cost seismic station and a L1-only GPS station. To date, three 'spiders' have been deployed on Soufrière Hills Volcano, the closest at ~1 km from the volcanic conduit, adjacent to a lava lobe on the dome. Here we present the details of GPS data processing in a network consisting of both dual and single frequency receivers ('spiders') using GAMIT/GLOBK software. Processing together single and dual frequency data allowed their representation in a common reference frame, and a meaningful geophysical interpretation of all the available data. We also present the 'spiders' time series along with the results from the rest of the network and examine if any significant deformation, correlating with other manifestations of volcanic activity, has been recorded by the 'spiders' since deployment. Our results demonstrate that low cost GNSS equipment can serve as valuable components in volcano deformation monitoring networks.

UNAVCO GPS High-Rate and Real-Time Products and Services: Building a next generation geodetic network.

NASA Astrophysics Data System (ADS)

Mencin, David; Meertens, Charles; Mattioli, Glen; Feaux, Karl; Looney, Sara; Sievers, Charles; Austin, Ken

2013-04-01

Recent advances in GPS technology and data processing are providing position estimates with centimeter-level precision at high-rate (1-5 Hz) and low latency (<1 s). Broad community interest in these data is growing rapidly because these data will have the potential to improve our understanding in diverse areas of geophysics including properties of seismic, volcanic, magmatic and tsunami deformation sources, and moreover profoundly transforming rapid event characterization, early warning, as well as hazard mitigation and response. Other scientific and operational applications for high-rate GPS also include glacier and ice sheet motions, tropospheric modeling, and better constraints on the dynamics of space weather. UNAVCO, through community input and the recent Plate Boundary Observatory (PBO) NSF-ARRA Cascadia initiative, has nearly completed the process of upgrading a total of 373 PBO GPS sites to real-time high-rate capability and these streams are now being archived in the UNAVCO data center. Further, through the UNAVCO core proposal (GAGE), currently under review at NSF, UNAVCO has proposed upgrading a significant portion of the ~1100 GPS stations that PBO currently operates to real-time high-rate capability to address community science and operational needs. In addition, in collaboration with NOAA, 74 of these stations will provide meteorological data in real-time, primarily to support watershed and flood analyses for regional early-warning systems related to NOAA's work with California Department of Water Resources. In preparation for this increased emphasis on high-rate GPS data, UNAVCO hosted an NSF funded workshop in Boulder, CO on March 26-28, 2012, which brought together 70 participants representing a spectrum of research fields with a goal to develop a community plan for the use of real-time GPS data products within the UNAVCO and EarthScope communities. These data products are expected to improve and expand the use of real-time, high-rate GPS data over the next decade.

Current Trends and Challenges in Satellite Laser Ranging

NASA Astrophysics Data System (ADS)

Appleby, Graham M.; Bianco, Giuseppe; Noll, Carey E.; Pavlis, Erricos C.; Pearlman, Michael R.

2016-12-01

Satellite Laser Ranging (SLR) is used to measure accurately the distance from ground stations to retro-reflectors on satellites and on the Moon. SLR is one of the fundamental space-geodetic techniques that define the International Terrestrial Reference Frame (ITRF), which is the basis upon which many aspects of global change over space, time, and evolving technology are measured; with VLBI the two techniques define the scale of the ITRF; alone the SLR technique defines its origin (geocenter). The importance of the reference frame has recently been recognized at the inter-governmental level through the United Nations, which adopted in February 2015 the Resolution "Global Geodetic Reference Frame for Sustainable Development." Laser Ranging provides precision orbit determination and instrument calibration and validation for satellite-borne altimeters for the better understanding of sea level change, ocean dynamics, ice mass-balance, and terrestrial topography. It is also a tool to study the dynamics of the Moon and fundamental constants and theories. With the exception of the currently in-orbit GPS constellation, all GNSS satellites now carry retro-reflectors for improved orbit determination, harmonization of reference frames, and in-orbit co-location and system performance validation; the next generation of GPS satellites due for launch from 2019 onwards will also carry retro-reflectors. The ILRS delivers weekly realizations that are accumulated sequentially to extend the ITRF and the Earth Orientation Parameter series with a daily resolution. SLR technology continues to evolve towards the next-generation laser ranging systems and it is expected to successfully meet the challenges of the GGOS2020 program for a future Global Space Geodetic Network. Ranging precision is improving as higher repetition rate, narrower pulse lasers, and faster detectors are implemented within the network. Automation and pass interleaving at some stations is expanding temporal coverage and greatly enhancing efficiency. Discussions are ongoing with some missions that will allow the SLR network stations to provide crucial, but energy-safe, range measurements to optically vulnerable satellites. New retro-reflector designs are improving the signal link and enable daylight ranging that is now the norm for many stations. We discuss many of these laser ranging activities and some of the tough challenges that the SLR network currently faces.

Poroelastic response to megathrust earthquakes: A look at the 2012 Mw 7.6 Costa Rican event

NASA Astrophysics Data System (ADS)

McCormack, K. A.; Hesse, M. A.

2017-12-01

Following an earthquake, surface deformation is influenced by a myriad of post-seismic processes including after-slip, poroelastic and viscoelastic relaxation. Geodetic measurements record the combined result of all these processes, which makes studying the effects of any single process difficult. To constrain the poroelastic component of post-seismic deformation, we model the subsurface hydrologic response to the Mw 7.6 subduction zone earthquake beneath the Nicoya peninsula on September 5, 2012. The regional-scale poroelastic model of the overlying plate integrates seismologic, geodetic and hydrologic data sets to predict the post-seismic poroelastic response. Following the earthquake, continuous surface deformation was observed with high-rate GPS monitoring directly above the rupture zone. By modeling the time-dependent deformation associated with poroelastic relaxation, we can begin to remove the contribution of groundwater flow from the observed geodetic signal. For this study we used both 2D and 3D numerical models. In 2D we investigate more general trends in the poroelastic response of a subduction zone earthquake. In 3D we model the poroelastic response to the 2012 Nicoya event using a fixed set of best fit parameters and the real earthquake slip data. The slip distribution of 2012 event is obtained by inverting the co-seismic surface GPS displacements for fault slip. The 2D model shows that thrust earthquakes with a rupture width less than a third of their depth produce complex multi-lobed pressure perturbations in the shallow subsurface. In the 3D model, the small width to depth ratio of the Nicoya rupture leads to a multi-lobed initial pore pressure distribution. This creates complex groundwater flow patterns, non-monotonic variations in well head and surface deformation, and poroelastic relaxation over multiple, distinct time scales. Different timescales arise because the earthquake causes pressure perturbations with different wavelengths. In the shallow, permeable region of the upper crust, two relaxation timescales of approximately 21 days and 18 months arise for the 2012 event. In the 18 months following the earthquake, the magnitude of the poroelastic surface deformation can be up to 3 cm for the vertical component and 2 cm for the trench-perpendicular component.

Stress coupling in the seismic cycle indicated from geodetic measurements

NASA Astrophysics Data System (ADS)

Wang, L.; Hainzl, S.; Zoeller, G.; Holschneider, M.

2012-12-01

The seismic cycle includes several phases, the interseismic, coseismic and postseismic phase. In the interseismic phase, strain gradually builds up around the overall locked fault in tens to thousands of years, while it is coseismically released in seconds. In the postseismic interval, stress relaxation lasts months to years, indicated by evident aseismic deformations which have been indicated to release comparable or even higher strain energy than the main shocks themselves. Benefiting from the development of geodetic observatory, e.g., Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR) in the last two decades, the measurements of surface deformation have been significantly improved and become valuable information for understanding the stress evolution on the large fault plane. In this study, we utilize the GPS/InSAR data to investigate the slip deficit during the interseismic phase, the coseismic slip and the early postseismic creep on the fault plane. However, it is already well-known that slip inversions based only on the surface measurements are typically non-unique and subject to large uncertainties. To reduce the ambiguity, we utilize the assumption of stress coupling between interseismic and coseismic phases, and between coseismic and postseismic phases. We use a stress constrained joint inversion in Bayesian approach (Wang et al., 2012) to invert simultaneously for (1) interseismic slip deficit and coseismic slip, and (2) coseismic slip and postseismic creep. As case studies, we analyze earthquakes occurred in well-instrumented regions such as the 2004 M6.0 Parkfield earthquake, the 2010 M8.7 earthquake and the 2011 M9.1 Tohoku-Oki earthquake. We show that the inversion with the stress-coupling constraint leads to better constrained slip distributions. Meanwhile, the results also indicate that the assumed stress coupling is reasonable and can be well reflected from the available geodetic measurements. Reference: Lifeng Wang, Sebastian Hainzl, Gert Zöller, Matthias Holschneider, M., 2012. Stress- and aftershock- constrained joint inversions for co- and post- seismic slip applied to the 2004 M6.0 Parkfield earthquake. J. Geophys. Res. doi:10.1029/2011JB009017.

Geodetic slip solutions for the Mw=7.4 Champerico (Guatemala) subduction earthquake of November 7 2012

NASA Astrophysics Data System (ADS)

Ellis, Andria; DeMets, Charles; Briole, Pierre; Molina, Enrique; Flores, Omar; Rivera, Jeffrey; Lasserre, Cécile; Lyon-Caen, Hélène; Lord, Neal

2014-05-01

As the first large subduction thrust earthquake off the coast of western Guatemala in the past 50 years, the 7 November 2012 Mw=7.4 earthquake offers the first opportunity for a geodetic study of coseismic and postseismic behavior for a segment of the Middle America trench where frictional coupling makes a transition from weak coupling off the coast of El Salvador to strong coupling in southern Mexico. Processing of continuous GPS measurements at 19 stations in Guatemala, El Salvador, and southern Mexico, and at 7 campaign points in Guatemala defines a highly consistent pattern of coseismic offsets during the earthquake, ranging from 47±5 mm of SW movement just inland from the earthquake epicenter to a few mm at sites located in northern Guatemala. Inversions of these offsets to find their best-fitting fault-slip solution in an elastic half space give a geodetic earthquake moment ranging between 0.75 and 1.1 x 1020 Nm, slightly smaller than the seismic estimates that range between 1.2 and 1.45 x 1020 Nm. Slip inversion using a constant slip model, assuming 293° and 29° for the fault azimuth and dip angle, indicates a nearly reverse slip of 2.8 m (rake 78°) on a fault plane 42 km-long and 20 km-wide, centered at 26 km depth. A variable slip inversion indicates that slip concentrated above depths of 40 km may have extended updip to the trench and reached a maximum of only 0.8 m, less than one-sixth the maximum slip indicated by a recent slip solution (5.3 m) obtained from waveform inversion of seismological data. Detailed model comparisons will be discussed. Transient postseismic displacements have been recorded at the nearby continuous GPS sites with amplitudes reaching 20-25 mm at some stations. The duration of the phenomenon is short: using an exponential-decay model, the estimated decay time is 90 ± 10 days. This postseismic signal is consistent with afterslip along a significantly broader area (+50%) of the subduction interface than ruptured coseismically. These results will be discussed in the tectonic framework of the area.

Seismic velocity change and slip rate during the 2006 Guerrero (Mexico) slow slip event

NASA Astrophysics Data System (ADS)

Rivet, Diane; Radiguet, Mathilde; Campillo, Michel; Cotton, Fabrice; Shapiro, Nikolai; Krishna Singh, Shri; Kostoglodov, Vladimir

2010-05-01

We measure temporal change of the seismic velocity in the crust below the Guerrero region during the 2006 slow sleep event (SSE). We use repeated cross-correlations of ambient seismic noise recorded at 26 broad-band stations of the MesoAmerica Seismic Experiment (MASE). The cross-correlations are computed over 90 days with a moving window of 10 days from January 2005 to July 2007. To insure measurements independent of noise source variations, we only take into account the travel time change within the coda. For period of 8 to 20s, we observe a decrease in velocity starting in April 2006 with a maximum change of -0.3% of the initial velocity in June 2006. At these periods, the Rayleigh waves are sensitive to velocity changes down to the lower crust. In the other hand, we compute the deformation rate below the MASE array from a slip propagation model of the SSE observed by means of the displacement time-series of 15 continuous GPS stations. Slip initiates in the western part of the Guerrero Gap and propagates southeastward. The propagation velocity is of the order of 1 km/day. We then compare the seismic velocity change measured from continuous seismological data with the deformation rate inferred from geodetic measurements below the MASE array. We obtain a good agreement between the time of maximal seismic velocity change (July 2006) and the time of maximum deformation associated with the SSE (July to August 2006). This result shows that the long-term velocity change associated with the SSE can be detected using continuous seismic recordings. Since the SSE does not emit seismic waves, which interact with the superficial layers, the result indicates that the velocity change is due to deformation at depth.

Crustal Deformation of the Central Walker Lane from GPS velocities: Block Rotations and Slip Rates

NASA Astrophysics Data System (ADS)

Bormann, J. M.; Hammond, W. C.; Kreemer, C. W.; Blewitt, G.; Wesnousky, S. G.

2010-12-01

The Walker Lane is a complex zone of active intracontinental transtension between the Sierra Nevada/Great Valley (SNGV) microplate and the Basin and Range in the western United States. Collectively, this ~100 km wide zone accommodates ~20% of the Pacific-North American relative plate motion. The Central Walker Lane (CWL) extends from the southern boundary of the Mina Deflection (~38.0°N) to the latitude of Lake Tahoe (~39.5°N) and encompasses the transition from Basin and Range style faulting in the east to the stable block motion of the SNGV microplate in the West. We combine GPS data from the Mobile Array of GPS for Nevada Transtension (MAGNET, http://geodesy.unr.edu/networks) with continuous observations from the EarthScope Plate Boundary Observatory to solve for rates of crustal deformation in the CWL through a block modeling approach. The GPS coordinate time series are derived in this region as part of a 7000-station global network solution using the latest JPL reanalysis of GPS orbits, and the latest antenna models for stations and satellites. The data were processed by precise point positioning using JPL's GIPSY OASIS II software followed by our custom Ambizap3 software, to produce a globally-consistent, ambiguity-resolved network solution. GPS time series in the western United States are rotated into a North America-fixed reference frame and are spatially filtered with respect to the secular motions of reference stations that demonstrate long-term secular stability. In the study region, we use 130 GPS velocities that are corrected for viscoelastic postseismic relaxation following 19th and 20th century earthquakes in the Central Nevada Seismic Belt to constrain rates of long-term fault slip and block rotation. The spatial density and precision of our velocity field (average station spacing of ~20 km with uncertainties well below 1 mm/yr) allow us to compare geodetically estimated slip rates with geologic observations as well as address specific questions about how shear is transferred from the Southern Walker Lane through the Mina Deflection and evaluate along-strike variation of the slip rate on the Sierra Nevada range front fault. Preliminary results confirm a pattern of deformation consistent with geological observations. Deformation zones are characterized by 1) left-lateral slip on east-northeast trending faults and clockwise block rotations in the Mina Deflection, 2) right-lateral slip on northwest trending faults along the eastern margin of the CWL, 3) east-west extension along north trending faults in the western portion of the CWL with right lateral slip increasing toward the SNGV microplate boundary, 4) clockwise rotation of blocks in the Carson Domain, and 5) northwest directed extension in the Basin and Range. Estimates of fault slip rates along the eastern boundary of the SNGV block find that slip is oblique with preliminary rates ranging between 0.4-0.8(±0.1) mm/yr horizontal extension and 0.9-1.5(±0.1) mm/yr right lateral.

Monitoring of Large Scale Volcanic Deformations in the Andes Using Geodetic Time Series (DInSAR, GPS and Microgravity)

NASA Astrophysics Data System (ADS)

Remy, D.; Froger, J. L.; Bonvalot, S.; Gabalda, G.; Albino, F.; Byrdina, S.

2010-03-01

Lastarria (25°10'S, 68°31'W, 5706 m) and Cordon del Azufre (25°18'S, 68°33'W, 5480 m) are part of a broad polygenic quaternary volcanic complex lying on the Altiplano, on the border of Chile and Argentina. This large scale volcanic area attracted particular attention in recent years because of its relatively intense unrest characterised by a peculiar style of on-going ground deformation, apparently begun in 1998. Interferometric Synthetic Aperture Radar (InSAR) data collected between 1998 and 2009 revealed two scales of inflation: a large elliptical area (50 km NNE- SSW major axis and a 40 minor axis), which has been inflating at a rate of around 3 cm.yr-1; and a short wavelength inflation (6 km wide), which is located at Lastarria volcano on the northern margin of the large elliptical area. The temporal evolution of these two distinct inflating signals suggests that they could be linked. The origin of this inflation period is still debated and various source mechanisms have been proposed to explain the observed deformation. Here, we present new observations of surface deformation in the Lastarria-Cordon del Azufre complex based on InSAR, levelling global positioning system (GPS), and microgravity data. Ascending and descending ASAR interferograms are combined to determine vertical and the EW horizontal component of displacement. Geodetic data are discussed from the standpoint of providing better constraints to understand the mechanics of the observed process at the volcanic complex.

Coseismic and postseismic deformation associated with the 2016 Mw 7.8 Kaikoura earthquake, New Zealand: fault movement investigation and seismic hazard analysis

NASA Astrophysics Data System (ADS)

Jiang, Zhongshan; Huang, Dingfa; Yuan, Linguo; Hassan, Abubakr; Zhang, Lupeng; Yang, Zhongrong

2018-04-01

The 2016 moment magnitude (Mw) 7.8 Kaikoura earthquake demonstrated that multiple fault segments can undergo rupture during a single seismic event. Here, we employ Global Positioning System (GPS) observations and geodetic modeling methods to create detailed images of coseismic slip and postseismic afterslip associated with the Kaikoura earthquake. Our optimal geodetic coseismic model suggests that rupture not only occurred on shallow crustal faults but also to some extent at the Hikurangi subduction interface. The GPS-inverted moment release during the earthquake is equivalent to a Mw 7.9 event. The near-field postseismic deformation is mainly derived from right-lateral strike-slip motions on shallow crustal faults. The afterslip did not only significantly extend northeastward on the Needles fault but also appeared at the plate interface, slowly releasing energy over the past 6 months, equivalent to a Mw 7.3 earthquake. Coulomb stress changes induced by coseismic deformation exhibit complex patterns and diversity at different depths, undoubtedly reflecting multi-fault rupture complexity associated with the earthquake. The Coulomb stress can reach several MPa during coseismic deformation, which can explain the trigger mechanisms of afterslip in two high-slip regions and the majority of aftershocks. Based on the deformation characteristics of the Kaikoura earthquake, interseismic plate coverage, and historical earthquakes, we conclude that Wellington is under higher seismic threat after the earthquake and great attention should be paid to potential large earthquake disasters in the near future.[Figure not available: see fulltext.

The SCEC geodetic transient detection validation exercise

USGS Publications Warehouse

Lohman, Rowena B.; Murray, Jessica R.

2013-01-01

Over the past decade the number and size of continuously operating Global Positioning System (GPS) networks has grown substantially worldwide. A steadily increasing volume of freely available GPS measurements, combined with the application of new approaches for mining these data for signals of interest, has led to the identification of a large and diverse collection of time‐varying Earth processes. One phenomenon that has been observed is transient fault slip (also termed slow slip events or silent earthquakes) occurring over time spans of days to years (e.g., Linde et al., 1996; Hirose et al., 1999; Dragert et al., 2001; Miller et al., 2002; Kostoglodov et al., 2003; Douglas et al., 2005; Shelly et al., 2006; Ide et al., 2007; Lohman and McGuire, 2007; Schwartz and Rokosky, 2007; Szeliga et al., 2008). Such events have been widely observed in subduction zones but are also found in other tectonic settings (Linde et al., 1996; Cervelli et al., 2002; Murray and Segall, 2005; Lohman and McGuire, 2007; Montgomery‐Brown et al., 2009; Shelly, 2010; and references therein). Although retrospective study of slow‐slip events using geodetic observations is driving the formulation of new models for fault‐zone behavior and constitutive laws (e.g., Lapusta et al., 2000; Liu and Rice, 2007; Lapusta and Liu, 2009; Segall and Bradley, 2012a), much of the research on near‐real‐time detection and characterization of anomalous behaviors along fault zones has focused solely on the use of seismic tremor (e.g., Rogers and Dragert, 2003; Shelly et al., 2006; Ito et al., 2007).

Precise Receiver Clock Offset Estimations According to Each Global Navigation Satellite Systems (GNSS) Timescales

NASA Astrophysics Data System (ADS)

Thongtan, Thayathip; Tirawanichakul, Pawit; Satirapod, Chalermchon

2017-12-01

Each GNSS constellation operates its own system times; namely, GPS system time (GPST), GLONASS system time (GLONASST), BeiDou system time (BDT) and Galileo system time (GST). They could be traced back to Coordinated Universal Time (UTC) scale and are aligned to GPST. This paper estimates the receiver clock offsets to three timescales: GPST, GLONASST and BDT. The two measurement scenarios use two identical multi-GNSS geodetic receivers connected to the same geodetic antenna through a splitter. One receiver is driven by its internal oscillators and another receiver is connected to the external frequency oscillators, caesium frequency standard, kept as the Thailand standard time scale at the National Institute of Metrology (Thailand) called UTC(NIMT). The three weeks data are observed at 30 seconds sample rate. The receiver clock offsets with respected to the three system time are estimated and analysed through the geodetic technique of static Precise Point Positioning (PPP) using a data processing software developed by Wuhan University - Positioning And Navigation Data Analyst (PANDA) software. The estimated receiver clock offsets are around 32, 33 and 18 nanoseconds from GPST, GLONASST and BDT respectively. This experiment is initially stated that each timescale is inter-operated with GPST and further measurements on receiver internal delay has to be determined for clock comparisons especially the high accuracy clock at timing laboratories.

An improved evaluation of the seismic/geodetic deformation-rate ratio for the Zagros Fold-and-Thrust collisional belt

NASA Astrophysics Data System (ADS)

Palano, Mimmo; Imprescia, Paola; Agnon, Amotz; Gresta, Stefano

2018-04-01

We present an improved picture of the ongoing crustal deformation field for the Zagros Fold-and-Thrust Belt continental collision zone by using an extensive combination of both novel and published GPS observations. The main results define the significant amount of oblique Arabia-Eurasia convergence currently being absorbed within the Zagros: right-lateral shear along the NW trending Main Recent fault in NW Zagros and accommodated between fold-and-thrust structures and NS right-lateral strike-slip faults on Southern Zagros. In addition, taking into account the 1909-2016 instrumental seismic catalogue, we provide a statistical evaluation of the seismic/geodetic deformation-rate ratio for the area. On Northern Zagros and on the Turkish-Iranian Plateau, a moderate to large fraction (˜49 and >60 per cent, respectively) of the crustal deformation occurs seismically. On the Sanandaj-Sirjan zone, the seismic/geodetic deformation-rate ratio suggests that a small to moderate fraction (<40 per cent) of crustal deformation occurs seismically; locally, the occurrence of large historic earthquakes (M ≥ 6) coupled with the high geodetic deformation, could indicate overdue M ≥ 6 earthquakes. On Southern Zagros, aseismic strain dominates crustal deformation (the ratio ranges in the 15-33 per cent interval). Such aseismic deformation is probably related to the presence of the weak evaporitic Hormuz Formation which allows the occurrence of large aseismic motion on both subhorizontal faults and surfaces of décollement. These results, framed into the seismotectonic framework of the investigated region, confirm that the fold-and-thrust-dominated deformation is driven by buoyancy forces; by contrast, the shear-dominated deformation is primary driven by plate stresses.

Geodetic Network Design and Optimization on the Active Tuzla Fault (Izmir, Turkey) for Disaster Management

PubMed Central

Halicioglu, Kerem; Ozener, Haluk

2008-01-01

Both seismological and geodynamic research emphasize that the Aegean Region, which comprises the Hellenic Arc, the Greek mainland and Western Turkey is the most seismically active region in Western Eurasia. The convergence of the Eurasian and African lithospheric plates forces a westward motion on the Anatolian plate relative to the Eurasian one. Western Anatolia is a valuable laboratory for Earth Science research because of its complex geological structure. Izmir is a large city in Turkey with a population of about 2.5 million that is at great risk from big earthquakes. Unfortunately, previous geodynamics studies performed in this region are insufficient or cover large areas instead of specific faults. The Tuzla Fault, which is aligned trending NE–SW between the town of Menderes and Cape Doganbey, is an important fault in terms of seismic activity and its proximity to the city of Izmir. This study aims to perform a large scale investigation focusing on the Tuzla Fault and its vicinity for better understanding of the region's tectonics. In order to investigate the crustal deformation along the Tuzla Fault and Izmir Bay, a geodetic network has been designed and optimizations were performed. This paper suggests a schedule for a crustal deformation monitoring study which includes research on the tectonics of the region, network design and optimization strategies, theory and practice of processing. The study is also open for extension in terms of monitoring different types of fault characteristics. A one-dimensional fault model with two parameters – standard strike-slip model of dislocation theory in an elastic half-space – is formulated in order to determine which sites are suitable for the campaign based geodetic GPS measurements. Geodetic results can be used as a background data for disaster management systems. PMID:27873783

Incorporating Geodetic Technologies in to Field and Campus Courses at the University of Michigan: Best Practices and Lessons Learned

NASA Astrophysics Data System (ADS)

Niemi, N. A.; Clark, M. K.

2017-12-01

For the past 6 years, the University of Michigan has implemented geodetic techniques into both summer field courses and on-campus courses. The primary means for incorporating these technologies has been a partnership with UNAVCO to introduce terrestrial laser scanning (TLS) at summer field courses, although employing Structure from Motion(SfM), ArcCollector for iPads and RTK GPS surveying have also been explored. The nature of these types of data lend themselves readily to geomorphology, environmental, and natural hazards-based projects, and we have developed field projects or labs around neotectonics (fault-scarp scanning and diffusion analysis), change detection (braided stream evolution, landslide and rock glacier motion, coastal change) and mass wasting processes (rock avalanche scanning and analysis). While we have primarily developed multi-day projects that use these tools in a field camp setting, we have also developed weekend field trip projects and traditional afternoon lab exercises associated with on-campus courses. The use of geodetic technology is generally well received by students. Reasons for this are the use of somewhat different skill sets from traditional geologic mapping problems, including research survey design, real-time data acquisition, and quantitative data analysis. Students also perceive that they are engaged in learning technology which they may use in their future employment. Challenges encountered, particularly in the field, include managing large student groups with a finite pool of equipment, rapid data processing pressures, variable student experience with analysis software and limited technical support for field-based computational resources. We will describe the positive attributes of incorporating geodetic technologies into undergraduate courses and elaborate on some best practices learned from our experiences.

Geodetic Network Design and Optimization on the Active Tuzla Fault (Izmir, Turkey) for Disaster Management.

PubMed

Halicioglu, Kerem; Ozener, Haluk

2008-08-19

Both seismological and geodynamic research emphasize that the Aegean Region, which comprises the Hellenic Arc, the Greek mainland and Western Turkey is the most seismically active region in Western Eurasia. The convergence of the Eurasian and African lithospheric plates forces a westward motion on the Anatolian plate relative to the Eurasian one. Western Anatolia is a valuable laboratory for Earth Science research because of its complex geological structure. Izmir is a large city in Turkey with a population of about 2.5 million that is at great risk from big earthquakes. Unfortunately, previous geodynamics studies performed in this region are insufficient or cover large areas instead of specific faults. The Tuzla Fault, which is aligned trending NE-SW between the town of Menderes and Cape Doganbey, is an important fault in terms of seismic activity and its proximity to the city of Izmir. This study aims to perform a large scale investigation focusing on the Tuzla Fault and its vicinity for better understanding of the region's tectonics. In order to investigate the crustal deformation along the Tuzla Fault and Izmir Bay, a geodetic network has been designed and optimizations were performed. This paper suggests a schedule for a crustal deformation monitoring study which includes research on the tectonics of the region, network design and optimization strategies, theory and practice of processing. The study is also open for extension in terms of monitoring different types of fault characteristics. A one-dimensional fault model with two parameters - standard strike-slip model of dislocation theory in an elastic half-space - is formulated in order to determine which sites are suitable for the campaign based geodetic GPS measurements. Geodetic results can be used as a background data for disaster management systems.

Evaluation of High-Precision Sensors in Structural Monitoring

PubMed Central

Erol, Bihter

2010-01-01

One of the most intricate branches of metrology involves the monitoring of displacements and deformations of natural and anthropogenic structures under environmental forces, such as tidal or tectonic phenomena, or ground water level changes. Technological progress has changed the measurement process, and steadily increasing accuracy requirements have led to the continued development of new measuring instruments. The adoption of an appropriate measurement strategy, with proper instruments suited for the characteristics of the observed structure and its environmental conditions, is of high priority in the planning of deformation monitoring processes. This paper describes the use of precise digital inclination sensors in continuous monitoring of structural deformations. The topic is treated from two viewpoints: (i) evaluation of the performance of inclination sensors by comparing them to static and continuous GPS observations in deformation monitoring and (ii) providing a strategy for analyzing the structural deformations. The movements of two case study objects, a tall building and a geodetic monument in Istanbul, were separately monitored using dual-axes micro-radian precision inclination sensors (inclinometers) and GPS. The time series of continuous deformation observations were analyzed using the Least Squares Spectral Analysis Technique (LSSA). Overall, the inclinometers showed good performance for continuous monitoring of structural displacements, even at the sub-millimeter level. Static GPS observations remained insufficient for resolving the deformations to the sub-centimeter level due to the errors that affect GPS signals. With the accuracy advantage of inclination sensors, their use with GPS provides more detailed investigation of deformation phenomena. Using inclinometers and GPS is helpful to be able to identify the components of structural responses to the natural forces as static, quasi-static, or resonant. PMID:22163499

Strategic planning of INA-CORS development for public service and tectonic deformation study

NASA Astrophysics Data System (ADS)

Syetiawan, Agung; Gaol, Yustisi Ardhitasari Lumban; Safi'i, Ayu Nur

2017-07-01

GPS technology can be applied for surveying, mapping and research purposes. The simplicity of GPS technology for positioning make it become the first choice for survey compared with another positioning method. GPS can measure a position with various accuracy level based on the measurement method. In order to facilitate the GPS positioning, many organizations are establishing permanent GPS station. National Geodetic Survey (NGS) called it as Continuously Operating Reference Stations (CORS). Those devices continuously collect and record GPS data to be used by users. CORS has been built by several government agencies for particular purposes and scattered throughout Indonesia. Geospatial Information Agency (BIG) as a geospatial information providers begin to compile a grand design of Indonesia CORS (INA-CORS) that can be used for public service such as Real Time Kinematic (RTK), RINEX data request, or post-processing service and for tectonic deformation study to determine the deformation models of Indonesia and to evaluate the national geospatial reference system. This study aims to review the ideal location to develop CORS network distribution. The method was used is to perform spatial analysis on the data distribution of BIG and BPN CORS overlayed with Seismotectonic Map of Indonesia and land cover. The ideal condition to be achieved is that CORS will be available on each radius of 50 km. The result showed that CORS distribution in Java and Nusa Tenggara are already tight while on Sumatra, Celebes and Moluccas are still need to be more tighten. Meanwhile, the development of CORS in Papua will encounter obstacles toward road access and networking. This analysis result can be used as consideration for determining the priorities of CORS development in Indonesia.

Accuracy assessment of the global TanDEM-X Digital Elevation Model with GPS data

NASA Astrophysics Data System (ADS)

Wessel, Birgit; Huber, Martin; Wohlfart, Christian; Marschalk, Ursula; Kosmann, Detlev; Roth, Achim

2018-05-01

The primary goal of the German TanDEM-X mission is the generation of a highly accurate and global Digital Elevation Model (DEM) with global accuracies of at least 10 m absolute height error (linear 90% error). The global TanDEM-X DEM acquired with single-pass SAR interferometry was finished in September 2016. This paper provides a unique accuracy assessment of the final TanDEM-X global DEM using two different GPS point reference data sets, which are distributed across all continents, to fully characterize the absolute height error. Firstly, the absolute vertical accuracy is examined by about three million globally distributed kinematic GPS (KGPS) points derived from 19 KGPS tracks covering a total length of about 66,000 km. Secondly, a comparison is performed with more than 23,000 "GPS on Bench Marks" (GPS-on-BM) points provided by the US National Geodetic Survey (NGS) scattered across 14 different land cover types of the US National Land Cover Data base (NLCD). Both GPS comparisons prove an absolute vertical mean error of TanDEM-X DEM smaller than ±0.20 m, a Root Means Square Error (RMSE) smaller than 1.4 m and an excellent absolute 90% linear height error below 2 m. The RMSE values are sensitive to land cover types. For low vegetation the RMSE is ±1.1 m, whereas it is slightly higher for developed areas (±1.4 m) and for forests (±1.8 m). This validation confirms an outstanding absolute height error at 90% confidence level of the global TanDEM-X DEM outperforming the requirement by a factor of five. Due to its extensive and globally distributed reference data sets, this study is of considerable interests for scientific and commercial applications.

Down and Out at Pacaya Volcano: A Glimpse of Magma Storage and Diking as Interpreted From GPS Geodesy

NASA Astrophysics Data System (ADS)

Lechner, H. N.; Waite, G. P.; Wauthier, D. C.; Escobar-Wolf, R. P.; Lopez-Hetland, B.

2017-12-01

Geodetic data from an eight-station GPS network at Pacaya volcano Guatemala allows us to produce a simple analytical model of deformation sources associated with the 2010 eruption and the eruptive period in 2013-2014. Deformation signals for both eruptive time-periods indicate downward vertical and outward horizontal motion at several stations surrounding the volcano. The objective of this research was to better understand the magmatic plumbing system and sources of this deformation. Because this down-and-out displacement is difficult to explain with a single source, we chose a model that includes a combination of a dike and spherical source. Our modelling suggests that deformation is dominated the inflation of a shallow dike seated high within the volcanic edifice and deflation of a deeper, spherical source below the SW flank of the volcano. The source parameters for the dike feature are in good agreement with the observed orientation of recent vent emplacements on the edifice as well the horizontal displacement, while the parameters for a deeper spherical source accommodate the downward vertical motion. This study presents GPS observations at Pacaya dating back to 2009 and provides a glimpse of simple models of possible deformation sources.

An Exploration of Software-Based GNSS Signal Processing at Multiple Frequencies

NASA Astrophysics Data System (ADS)

Pasqual Paul, Manuel; Elosegui, Pedro; Lind, Frank; Vazquez, Antonio; Pankratius, Victor

2017-01-01

The Global Navigation Satellite System (GNSS; i.e., GPS, GLONASS, Galileo, and other constellations) has recently grown into numerous areas that go far beyond the traditional scope in navigation. In the geosciences, for example, high-precision GPS has become a powerful tool for a myriad of geophysical applications such as in geodynamics, seismology, paleoclimate, cryosphere, and remote sensing of the atmosphere. Positioning with millimeter-level accuracy can be achieved through carrier-phase-based, multi-frequency signal processing, which mitigates various biases and error sources such as those arising from ionospheric effects. Today, however, most receivers with multi-frequency capabilities are highly specialized hardware receiving systems with proprietary and closed designs, limited interfaces, and significant acquisition costs. This work explores alternatives that are entirely software-based, using Software-Defined Radio (SDR) receivers as a way to digitize the entire spectrum of interest. It presents an overview of existing open-source frameworks and outlines the next steps towards converting GPS software receivers from single-frequency to dual-frequency, geodetic-quality systems. In the future, this development will lead to a more flexible multi-constellation GNSS processing architecture that can be easily reused in different contexts, as well as to further miniaturization of receivers.

Atmospheric Delay Reduction Using KARAT for GPS Analysis and Implications for VLBI

NASA Technical Reports Server (NTRS)

Ichikawa, Ryuichi; Hobiger, Thomas; Koyama, Yasuhiro; Kondo, Tetsuro

2010-01-01

We have been developing a state-of-the-art tool to estimate the atmospheric path delays by raytracing through mesoscale analysis (MANAL) data, which is operationally used for numerical weather prediction by the Japan Meteorological Agency (JMA). The tools, which we have named KAshima RAytracing Tools (KARAT)', are capable of calculating total slant delays and ray-bending angles considering real atmospheric phenomena. The KARAT can estimate atmospheric slant delays by an analytical 2-D ray-propagation model by Thayer and a 3-D Eikonal solver. We compared PPP solutions using KARAT with that using the Global Mapping Function (GMF) and Vienna Mapping Function 1 (VMF1) for GPS sites of the GEONET (GPS Earth Observation Network System) operated by Geographical Survey Institute (GSI). In our comparison 57 stations of GEONET during the year of 2008 were processed. The KARAT solutions are slightly better than the solutions using VMF1 and GMF with linear gradient model for horizontal and height positions. Our results imply that KARAT is a useful tool for an efficient reduction of atmospheric path delays in radio-based space geodetic techniques such as GNSS and VLBI.

The effect of observing session duration on OPUS-RS results

NASA Astrophysics Data System (ADS)

Dincer Dogru, A.; Ugur Sanli, D.; Hayal, Adem G.; Berber, Mustafa

2016-04-01

Online GPS positioning software has now a widespread interest among practitioners and researchers. Researchers rescently use online software to monitor natural hazards such as landslides. The fact that this software usually employs continuously operating GPS stations of the International GNSS Service (IGS) as reference stations in the processing, the community of world-wide users is growing day by day. In the monitoring of landslides, rapid static mode of a GPS surveying is usually preferred because it is possible to have wider field coverage with only a few minutes of data and low cost ground markers. Results comparable to static positioning can be obtained with careful network design and processing strategies. Some online software such as OPUS-RS developed by the National Geodetic Survey (NGS) of the USA provides rapid static positioning engine that processes GPS data from sessions of only a few minutes. 15-minute is the recommended/standard observing session duration for OPUS-RS processing. In this study, using the CORS data operating in the US, we carried out some tests in which the observing session duration is changed from 8 through 118 minutes, and observed the accuracy change on the OPUS-RS solutions. Then we compared the results with the accuracy levels given for 15-min solutions by the NGS. We determined that there is the effect of changing observing session duration on the obtained results, and we report them in this study.

Use of GPS ASHTECH Z12T receivers for accurate time and frequency comparisons.

PubMed

Petit, G; Thomas, C; Jiang, Z; Uhrich, P; Taris, F

1999-01-01

The GPS phase measurements described in this paper were obtained using two similar multichannel GPS ASHTECH Z12T receivers belonging to the Bureau International des Poids et Mesures, BIPM, and the Laboratoire Primaire du Temps et des Frequences, BNM-LPTF. These receivers are based on the conventional geodetic ASHTECH Z12 unit, which has been modified to meet the stability requirements of time and frequency comparisons. Comparison of the two receivers operated side by side in different antenna configurations shows typical short-term noise of 1.1 to 3.5 ps. Longer term variations indicate a temperature sensitivity in the equipment, which limits the performance of the GPS phase method. One of the receivers was successfully operated using a temperature-stabilized antenna TSA from 3S Navigation, and the ASHTECH antenna, which feeds the second receiver, was placed in a home-built oven maintained at a constant temperature. These precautions made it possible to reduce a number of systematic effects. A separate study of frequency comparison was carried out between two hydrogen-masers located at the BNM-LPTF (Paris, France) and the PTB (Braunschweig, Germany) using receivers similar to ASHTECH Z12T receivers. The relative frequency stability obtained was about 3.3x10(-15) for an average time of 15 000 s, an interesting result comparable with the outstanding performance of new ultrastable frequency standards.

Compact Integration of a GSM-19 Magnetic Sensor with High-Precision Positioning using VRS GNSS Technology

PubMed Central

Martín, Angel; Padín, Jorge; Anquela, Ana Belén; Sánchez, Juán; Belda, Santiago

2009-01-01

Magnetic data consists of a sequence of collected points with spatial coordinates and magnetic information. The spatial location of these points needs to be as exact as possible in order to develop a precise interpretation of magnetic anomalies. GPS is a valuable tool for accomplishing this objective, especially if the RTK approach is used. In this paper the VRS (Virtual Reference Station) technique is introduced as a new approach for real-time positioning of magnetic sensors. The main advantages of the VRS approach are, firstly, that only a single GPS receiver is needed (no base station is necessary), reducing field work and equipment costs. Secondly, VRS can operate at distances separated 50–70 km from the reference stations without degrading accuracy. A compact integration of a GSM-19 magnetometer sensor with a geodetic GPS antenna is presented; this integration does not diminish the operational flexibility of the original magnetometer and can work with the VRS approach. The coupled devices were tested in marshlands around Gandia, a city located approximately 100 km South of Valencia (Spain), thought to be the site of a Roman cemetery. The results obtained show adequate geometry and high-precision positioning for the structures to be studied (a comparison with the original low precision GPS of the magnetometer is presented). Finally, the results of the magnetic survey are of great interest for archaeological purposes. PMID:22574055

Tectonic stressing in California modeled from GPS observations

USGS Publications Warehouse

Parsons, T.

2006-01-01

What happens in the crust as a result of geodetically observed secular motions? In this paper we find out by distorting a finite element model of California using GPS-derived displacements. A complex model was constructed using spatially varying crustal thickness, geothermal gradient, topography, and creeping faults. GPS velocity observations were interpolated and extrapolated across the model and boundary condition areas, and the model was loaded according to 5-year displacements. Results map highest differential stressing rates in a 200-km-wide band along the Pacific-North American plate boundary, coinciding with regions of greatest seismic energy release. Away from the plate boundary, GPS-derived crustal strain reduces modeled differential stress in some places, suggesting that some crustal motions are related to topographic collapse. Calculated stressing rates can be resolved onto fault planes: useful for addressing fault interactions and necessary for calculating earthquake advances or delays. As an example, I examine seismic quiescence on the Garlock fault despite a calculated minimum 0.1-0.4 MPa static stress increase from the 1857 M???7.8 Fort Tejon earthquake. Results from finite element modeling show very low to negative secular Coulomb stress growth on the Garlock fault, suggesting that the stress state may have been too low for large earthquake triggering. Thus the Garlock fault may only be stressed by San Andreas fault slip, a loading pattern that could explain its erratic rupture history.

Crust-mantle mechanical coupling in Eastern Mediterranean and Eastern Turkey

PubMed Central

Sinan Özeren, M.

2012-01-01

Present-day crust-mantle coupling in the Eastern Mediterranean and eastern Turkey is studied using the Global Positioning System (GPS) and seismic anisotropy data. The general trend of the shear wave fast-splitting directions in NE Turkey and Lesser Caucaus align well with the geodetic velocities in an absolute plate motion frame of reference pointing to an effective coupling in this part of the region of weak surface deformation. Farther south, underneath the Bitlis Suture, however, there are significant Pn delays with E-W anisotropy axes indicating significant lateral escape. Meanwhile, the GPS reveals very little surface deformation. This mismatch possibly suggests a decoupling along the suture. In the Aegean, the shear wave anisotropy and the Pn anisotropy directions agree with the extensional component of the right-lateral shear strains except under the Crete Basin and other parts of the southern Aegean Sea. This extensional direction matches perfectly also with the southward pulling force vectors across the Hellenic trench; however, the maximum right-lateral shear directions obtained from the GPS data in the Aegean do not match either of these anisotropies. Seismic anisotropy from Rayleigh waves sampled at 15 s, corresponding to the lower crust, match the maximum right-lateral maximum shear directions from the GPS indicating decoupling between the crust and the mantle. This decoupling most likely results from the lateral variations of the gravitational potential energies and the slab-pull forces. PMID:22592788

Crust-mantle mechanical coupling in Eastern Mediterranean and eastern Turkey.

PubMed

Özeren, M Sinan

2012-05-29

Present-day crust-mantle coupling in the Eastern Mediterranean and eastern Turkey is studied using the Global Positioning System (GPS) and seismic anisotropy data. The general trend of the shear wave fast-splitting directions in NE Turkey and Lesser Caucaus align well with the geodetic velocities in an absolute plate motion frame of reference pointing to an effective coupling in this part of the region of weak surface deformation. Farther south, underneath the Bitlis Suture, however, there are significant Pn delays with E-W anisotropy axes indicating significant lateral escape. Meanwhile, the GPS reveals very little surface deformation. This mismatch possibly suggests a decoupling along the suture. In the Aegean, the shear wave anisotropy and the Pn anisotropy directions agree with the extensional component of the right-lateral shear strains except under the Crete Basin and other parts of the southern Aegean Sea. This extensional direction matches perfectly also with the southward pulling force vectors across the Hellenic trench; however, the maximum right-lateral shear directions obtained from the GPS data in the Aegean do not match either of these anisotropies. Seismic anisotropy from Rayleigh waves sampled at 15 s, corresponding to the lower crust, match the maximum right-lateral maximum shear directions from the GPS indicating decoupling between the crust and the mantle. This decoupling most likely results from the lateral variations of the gravitational potential energies and the slab-pull forces.

PBO Nucleus Project Status: Integration of 209 Existing GPS Stations into the Plate Boundary Observatory

NASA Astrophysics Data System (ADS)

Blume, F.; Meertens, C.; Anderson, G.; Eriksson, S.; Boyce, E.

2007-12-01

Tectonic and earthquake research in the US has experienced a quiet revolution over the last decade precipitated by the recognition that slow-motion faulting events can both trigger and be triggered by regular earthquakes. Transient motion has now been found in essentially all tectonic environments, and the detection and analysis of such events is the first-order science target of the EarthScope Project. Because of this and a host of other fundamental tectonics questions that can be answered only with long-duration geodetic time series, the incipient 1100-station EarthScope Plate Boundary Observatory (PBO) network has been designed to leverage 445 existing continuous GPS stations whose measurements extend back over a decade. The irreplaceable recording history of these stations will accelerate EarthScope scientific return by providing the highest possible resolution. This resolution will be used to detect and understand transients, to determine the three-dimensional velocity field (particularly vertical motion), and to improve measurement precision by understanding the complex noise sources inherent in GPS. The PBO Nucleus project supports the operation, maintenance and hardware upgrades of a subset of the six western U.S. geodetic networks until they are subsumed by PBO. Uninterrupted data flow from these stations will effectively double the time-series length of PBO over the expected life of EarthScope, and has created, for the first time, a single GPS-based geodetic network in the US. The other existing sites remain in operation under support from non-NSF sources (e.g. the USGS), and EarthScope continues to benefit from their continued operation On the grounds of relevance to EarthScope science goals, geographic distribution and data quality, 209 of the 432 existing stations were selected as the nucleus upon which to build PBO. Conversion of these stations to a PBO-compatible mode of operation was begun under previous funding, and as a result data now flow directly to PBO archives and processing centers while maintenance, operations, and meta-data requirements are continue to be upgraded to PBO standards. At the end of this project all 209 stations will be fully incorporated into PBO, meeting all standards for new PBO construction including data communications and land use permits. Funds for operation of these stations have been included in planned budgets for PBO after the construction phase ends and PBO begins an operational phase in 2008. At this time work on the project is apporixmately 80% complete, with over 90% of the stations having been upgraded. The data from these stations serve a much larger audience than just the few people who work to keep them operating. This project is now collecting the data that will be used by the next generation of solid-earth researchers for at least two decades. Educational modules are being developed by a team of researchers, educators, and curriculum development professionals, and are being disseminated through regional and national workshops. An interactive website provides the newest developments in tectonics research to K-16 classrooms.

Seafloor horizontal positioning from a continuously operating buoy-based GPS-acoustic array

NASA Astrophysics Data System (ADS)

Chadwell, C. D.; Brown, K. M.; Tryon, M. D.; Send, U.

2009-12-01

Seafloor horizontal positions in a global frame were estimated daily from an autonomous buoy operating continuously over several months. The buoy (GEOCE) was moored offshore San Diego in 100-m-deep waters above an array of 4 seafloor transponders. Dual-frequency GPS data were collected at 1-Hz at a main antenna on the buoy and at 3 shore stations to provide continuous 2-3 cm positions of the buoy main antenna. Two single-frequency antennas on the buoy along with the main antenna were used to estimate the buoy attitude and short-term velocity. At one minute intervals the two-way acoustic travel time was measured between the buoy and transponders. During this few second span when transmitting and receiving acoustic signals, 10-Hz attitude and velocity were collected to locate the position of the transducer mounted approximately 2 m below the water line. The GPS and acoustic data were recorded internally and transmitted to shore over a cell-phone link and/or a wireless Ethernet. GPS data were combined with the acoustic data to estimate the array location at 1 minute intervals. The 1-minute positions are combined to provide a daily estimate of the array position. The buoy is autonomous, solar-powered and in addition to the GPS and acoustic data collects air pressure, temperature, wind speed/direction as well as water level at the surface and conductivity and temperature along the mooring line from near the sea surface to just above the sea floor. Here we report results from the horizontal positioning effort from Phase I of the project in shallow waters. The project also includes a vertical deformation sensor and physical oceanographic monitoring. A deep water (nominally 1000 m) test is planned for 2010. This work is supported by NSF-OCE-0551363 of the Ocean Technology and Interdisciplinary Coordination Program.

Star Scheduling Mode—A New Observing Strategy for Monitoring Weak Southern Radio Sources with the AuScope VLBI Array

NASA Astrophysics Data System (ADS)

McCallum, Lucia; Mayer, David; Le Bail, Karine; Schartner, Matthias; McCallum, Jamie; Lovell, Jim; Titov, Oleg; Shu, Fengchun; Gulyaev, Sergei

2017-11-01

The International Celestial Reference Frame suffers from significantly less observations in the southern hemisphere compared to the northern one. One reason for this is the historically low number of very long baseline interferometry radio telescopes in the south. The AuScope very long baseline interferometry array with three new telescopes on the Australian continent and an identical antenna in New Zealand were built to address this issue. While the overall number of observations in the south has greatly improved since then, a closer look reveals that this improvement is only true for strong radio sources (source flux densities >0.6 Jy). The new array of small very long baseline interferometry antennas has a relatively low baseline sensitivity so that only strong sources can be observed within a short integration time. A new observing strategy, the star scheduling mode, was developed to enable efficient observations of weak sources during geodetic sessions, through the addition of a single more sensitive antenna to the network. This scheduling mode was implemented in the Vienna very long baseline interferometry Software and applied in four 24-h sessions in 2016. These observations provide updated positions and source flux densities for 42 weak southern radio sources and significantly reduce the formal uncertainties for these sources. The star scheduling mode now allows the AuScope very long baseline interferometry array to undertake greater responsibility in monitoring sources in the southern sky, without significantly weakening the session for geodetic purposes.

Magmatic processes evidenced by borehole dilatometer data at Campi Flegrei, Italy.

NASA Astrophysics Data System (ADS)

Di Lieto, Bellina; Romano, Pierdomenico; Scarpa, Roberto; Orazi, Massimo

2017-04-01

Since spring 2004 a joint research project (AMRA, UniSa, INGV) has been developed in Italy to install borehole strainmeters aimed at enhanced INGV monitoring systems. Six Sacks-Evertson dilatometers were installed around Campi Flegrei and Vesuvius during 2004-2005, and in 2008 these were supplemented by two arrays of long-baseline underground water tube tiltmeters. Renewed activity started since 2004-2005, characterized by a low rate of vertical displacement, amounting initially to a few cm/year. Recent deformation in the Campi Flegrei caldera is dominated by aseismic inflation, interrupted by minor transient aseismic reversals in rate. These are typically below the noise level or are poorly sampled by the low sampling frequency of most geodetic techniques, but can be quantified relatively easily using high sensitivity strainmeters and tiltmeters. These instruments provide coherent views of deformation at several different time scales capturing reversals in rate with periods from minutes to months. Monotonic uplift episodes have been recorded with durations of several weeks to a few years. During the summer of 2006 a long term strain episode related to an increase of CO2 emission, evidenced by borehole tiltmeters and continuous GPS sensors, has been observed by the borehole dilatometers array. This strain episode preceded caldera microseismic activity by few months, as was also observed during the 1982 period of unrest. Other aseismic slip episodes were recorded in October 2006 and in March 2010, several minutes before the most significant seismic swarms (VT and/or LP events) occurred after the 1982-1984 uplift. The time scale of these transient strain events lasted less than one hour, putting further constraints on the origin of ground uplifts at Campi Flegrei. Their locations are compatible with the source inferred from long term deformation signals, at about 4 km depth beneath Pozzuoli. The current array provides us with a glimpse of the potential utility of a dense array of strainmeters and tiltmeters surrounding the Campi Flegrei region. An expanded array of tiltmeters and strainmeters operating continuously would permit the details of magma-transfer and the underlying cause of subsequent seismic activity to be monitored. Despite the small number of sensors, a preliminary mechanism model for aseismic strain episodes can be defined, correlating these episodes with magma growth in reservoirs with occasional pressure relief associated with the leakage of gas.

Present-Day Kinematics of the Dead Sea Transform and Internal Deformation within the Sinai and Arabian Plates

NASA Astrophysics Data System (ADS)

Gomez, F. G.; Yassminh, R.; Cochran, W. J.; Reilinger, R. E.; Barazangi, M.

2015-12-01

An updated GPS velocity field along the Dead Sea Fault (DSF) provides a basis for assessing off-transform strain within the Sinai and Arabian plates along entire length of this left-lateral, continental transform. As one of the main tectonic elements in the eastern Mediterranean region, an improved kinematic view of the DSF elucidates the broader understanding of the regional tectonic framework, as well as contributes to refining the earthquake hazard assessment. Reconciling short-term (geodetic) measurements of crustal strain with neotectonic data on fault movements can yield insight into the mechanical and rheological properties of crustal deformation associated with transform tectonics. In addition to regional continuous GPS stations, this study assembles results from campaign GPS networks in Syria, Lebanon, and Jordan spanning more than a decade. 1-sigma uncertainties on velocities range from less than 0.4 mm/yr (continuous stations and older GPS survey sites) to about 1.0 mm/yr (newer survey sites). Analyses using elastic block models suggest slip rates of 4.0 - 5.0 mm/yr along the southern and central DSF and slip rates of 2.0 - 3.0 mm/yr along the northern DSF, and fault locking depths also vary along strike of the transform. Furthermore, the spatial distribution of GPS observations permits analyzing residual strains within the adjacent plates, after plate boundary strain is removed. A key observation is horizontal stretching within the Sinai plate, which may be related to pull by the subducted slab of the Sinai plate. Within the Arabian plate, areas of horizontal stretching generally correlate with locations of Quaternary volcanism.

InSAR tropospheric delay mitigation by GPS observations: A case study in Tokyo area

NASA Astrophysics Data System (ADS)

Xu, Caijun; Wang, Hua; Ge, Linlin; Yonezawa, Chinatsu; Cheng, Pu

2006-03-01

Like other space geodetic techniques, interferometric synthetic aperture radar (InSAR) is limited by the variations of tropospheric delay noise. In this paper, we analyze the double-difference (DD) feature of tropospheric delay noise in SAR interferogram. By processing the ERS-2 radar pair, we find some tropospheric delay fringes, which have similar patterns with the GMS-5 visible-channel images acquired at almost the same epoch. Thirty-five continuous GPS (CGPS) stations are distributed in the radar scene. We analyze the GPS data by GIPSY-OASIS (II) software and extract the wet zenith delay (WZD) parameters at each station at the same epoch with the master and the slave image, respectively. A cosine mapping function is applied to transform the WZD to wet slant delay (WSD) in line-of-sight direction. Based on the DD WSD parameters, we establish a two-dimensional (2D) semi-variogram model, with the parameters 35.2, 3.6 and 0.88. Then we predict the DD WSD parameters by the kriging algorithm for each pixel of the interferogram, and subtract it from the unwrapped phase. Comparisons between CGPS and InSAR range changes in LOS direction show that the root of mean squares (RMS) decreased from 1.33 cm before correction to 0.87 cm after correction. From the result, we can conclude that GPS WZD parameters can be effectively used to identify and mitigate the large-scale InSAR tropospheric delay noise if the spatial resolution of GPS stations is dense enough.

COCONet enhancements to circum-Caribbean tsunami warning, tidal, and sea-level monitoring: update on tide gauge installations

NASA Astrophysics Data System (ADS)

Dausz, K.; Dittmann, S. T.; Feaux, K.; von Hillebrandt-Andrade, C.; Mattioli, G. S.; Normandeau, J.

2014-12-01

The Continually Operating Caribbean GPS Observational Network (COCONet) is a National Science Foundation (NSF) funded multi-hazard geodetic and meteorological network distributed throughout the Caribbean, which provides infrastructure and capacity building for a broad range of earth science questions. The network is a multi-national collaboration consisting of 46 newly constructed continuous Global Positioning Systems (cGPS) and 21 refurbished existing GPS stations, all co-located with meteorological sensors. One recommendation of the COCONet working group was to improve the vertical reference frame for long-term sea level monitoring. A COCONet supplement was awarded by the NSF to further address this particular objective through the co-location of GPS and tide gauges. This COCOnet infrastructure, along with the new tide gauges, will have broad scientific implications for hazards mitigation, solid earth, and atmospheric science research. UNAVCO engineers have meet with members of the Caribbean tide gauge community to establish target locations and design station layout. Allocated NSF funds allow for the construction of two complete new tide gauge systems each with two complimentary cGPS. Following the recommendations of NOAA and the sea level monitoring community, the two "new" locales will be Port Royal, Jamaica and Puerto Morelos, Mexico. Both locations had previously existing, but currently non-operational tide gauges. UNAVCO engineers will install a Sutron Radar Level Recorder and a backup pressure sensor tide gauge with GOES satellite telemetry. Tide data will be freely available by the Intergovernmental Oceanographic Commission (www.ioc-sealevelmonitoring.org). The NSF supplement also provided funds for adding cGPS to two additional locations where currently functioning tide gauge systems exist. Proposed locations for this additional infrastructure are Barahona, Dominican Republic and Bocas del Toro, Panama. All four locations will feature two standard COCONet cGPS systems consisting of a Trimble Choke Ring GNSS antenna, Trimble NetR9 GPS receiver, and a Vaisala meteorological sensor. All GPS data will be collected, processed and distributed via standard COCONet archiving and processing along with raw meteorological data at coconet.unavco.org.

Added-value joint source modelling of seismic and geodetic data

NASA Astrophysics Data System (ADS)

Sudhaus, Henriette; Heimann, Sebastian; Walter, Thomas R.; Krueger, Frank

2013-04-01

In tectonically active regions earthquake source studies strongly support the analysis of the current faulting processes as they reveal the location and geometry of active faults, the average slip released or more. For source modelling of shallow, moderate to large earthquakes often a combination of geodetic (GPS, InSAR) and seismic data is used. A truly joint use of these data, however, usually takes place only on a higher modelling level, where some of the first-order characteristics (time, centroid location, fault orientation, moment) have been fixed already. These required basis model parameters have to be given, assumed or inferred in a previous, separate and highly non-linear modelling step using one of the these data sets alone. We present a new earthquake rupture model implementation that realizes a fully combined data integration of surface displacement measurements and seismic data in a non-linear optimization of simple but extended planar ruptures. The model implementation allows for fast forward calculations of full seismograms and surface deformation and therefore enables us to use Monte Carlo global search algorithms. Furthermore, we benefit from the complementary character of seismic and geodetic data, e. g. the high definition of the source location from geodetic data and the sensitivity of the resolution of the seismic data on moment releases at larger depth. These increased constraints from the combined dataset make optimizations efficient, even for larger model parameter spaces and with a very limited amount of a priori assumption on the source. A vital part of our approach is rigorous data weighting based on the empirically estimated data errors. We construct full data error variance-covariance matrices for geodetic data to account for correlated data noise and also weight the seismic data based on their signal-to-noise ratio. The estimation of the data errors and the fast forward modelling opens the door for Bayesian inferences of the source model parameters. The source model product then features parameter uncertainty estimates and reveals parameter trade-offs that arise from imperfect data coverage and data errors. We applied our new source modelling approach to the 2010 Haiti earthquake for which a number of apparently different seismic, geodetic and joint source models has been reported already - mostly without any model parameter estimations. We here show that the variability of all these source models seems to arise from inherent model parameter trade-offs and mostly has little statistical significance, e.g. even using a large dataset comprising seismic and geodetic data the confidence interval of the fault dip remains as wide as about 20 degrees.

Seafloor seismological/geodetic observations in the rupture area of the 2011 Tohoku-oki Earthquake

NASA Astrophysics Data System (ADS)

Hino, Ryota; Shinohara, Masanao; Ito, Yoshihiro

2016-04-01

A number of important aspects of the 2011 Tohoku-oki earthquake (Mw 9.0) were clarified by the seafloor seismological and geodetic observation above the rupture area of the earthquake. Besides the extraordinarily large coseismic displacements, various kinds of slow slip phenomena associated with intensive micro-seismicity on the plate boundary fault were identified by near field ocean bottom seismographs and seafloor geodetic observation networks. The Tohoku-oki earthquake was preceded by evident foreshock activity with a spatial expansion of this seismicity. The activity became significantly intense after the occurrence of the largest foreshock two days before the mainshock rupture. During the period, clear continuous seafloor deformation was identified caused by the aseismic slip following the largest foreshock. Another different type of aseismic slip event had occurred before this pre-imminent activity had started about a month before the largest foreshock happened. The observed increased seismicity associated with aseismic slip suggests that there must have been some chain reaction like interplay of seismic and interseismic slips before the large earthquake broke out. However, no evident deformation signals were observed indicating acceleration of fault slip immediately before the mainshock. Seafloor geodetic measurements reveals that the postseismic deformation around the rupture area of the Tohoku-oki earthquake shows complex spatial pattern and the complexity is mostly due to significant viscoelastic relaxation induced by the huge coseismic slip. The effects of viscoelastic deformation makes it difficult to identify the deformation associated with the after slip or regaining of interplate coupling and requires us to enhance the abilities of seafloor monitoring to detect the slip activities on the fault. We started an array of seismometer arrays observation including broad-band seismographs to detect and locate slow-slip events and low-frequency tremors. Another observation we started is direct-path acoustic ranging across the trench axis. Slip rate of the shallow fault can be measured by monitoring the change in distance between the benchmarks on the incoming and overrding plates.

Polish Geophysical Solid Earth Infrastructure Contributing to EPOS

NASA Astrophysics Data System (ADS)

Debski, W.; Mutke, G.; Suchcicki, J.; Jozwiak, W.; Wiejacz, P.; Trojanowski, J.

2012-04-01

In this poster we present the current state of the main polish solid-earth-orientated infrastructures and shortly described history of their development, current state, and some plans for their future development. The presen- tation concentrates only on the classical infrastructure leaving aside for the while the the geodetic-orientated infrastructure, like GPS network and the GPS processing data centers, gravimetric infrastructure and others of this type. Polish broadband seismic infrastructure consists of 7 permanent broadband stations incorporated into the VEBSN initiative running at the polish territory and one operated in collaboration with NORSAR is settled at the Hornsund (Svalbard) polish polar station. All stations are equipped with STS-2 seismometers and polish MK-6 seismic stations providing 120 dB dynamics 100Hz sampling and data transmission in a real time to processing center. Besides this permanent broadband seismic network (PLSN) the Central Institute of Mining is running the permanent regional, short period network at the Upper Silesia area dedicated to the detailed monitoring of seismicity induced by the black coal mining activity in this area. The network consists of As the mining activity is the main source of seismicity in Poland also all mines are running underground short period networks, like for example Rudna-Polkowice copper mine seismic network consisting of 64 underground located short period seimometers. In that area, especially around the Zelazny Most: the huge post-floating artificial lake the, IGF PAS is running the local seismic array consisting of 4 short period seismometers. Besides these permanent network IGF PAN is running the portable seismic network for detailed mapping a possible natural seismic activity in selected regions of Poland. Important contribution to classical geophysical observation in the electro-magnetic field are provided by three permanent geomagnetic observatories (one at Hornsund) and supporting set of 10 portable, high-accuracy magnetoteluric stations.

Linear homotopy solution of nonlinear systems of equations in geodesy

NASA Astrophysics Data System (ADS)

Paláncz, Béla; Awange, Joseph L.; Zaletnyik, Piroska; Lewis, Robert H.

2010-01-01

A fundamental task in geodesy is solving systems of equations. Many geodetic problems are represented as systems of multivariate polynomials. A common problem in solving such systems is improper initial starting values for iterative methods, leading to convergence to solutions with no physical meaning, or to convergence that requires global methods. Though symbolic methods such as Groebner bases or resultants have been shown to be very efficient, i.e., providing solutions for determined systems such as 3-point problem of 3D affine transformation, the symbolic algebra can be very time consuming, even with special Computer Algebra Systems (CAS). This study proposes the Linear Homotopy method that can be implemented easily in high-level computer languages like C++ and Fortran that are faster than CAS by at least two orders of magnitude. Using Mathematica, the power of Homotopy is demonstrated in solving three nonlinear geodetic problems: resection, GPS positioning, and affine transformation. The method enlarging the domain of convergence is found to be efficient, less sensitive to rounding of numbers, and has lower complexity compared to other local methods like Newton-Raphson.

VLBI observations to the APOD satellite

NASA Astrophysics Data System (ADS)

Sun, Jing; Tang, Geshi; Shu, Fengchun; Li, Xie; Liu, Shushi; Cao, Jianfeng; Hellerschmied, Andreas; Böhm, Johannes; McCallum, Lucia; McCallum, Jamie; Lovell, Jim; Haas, Rüdiger; Neidhardt, Alexander; Lu, Weitao; Han, Songtao; Ren, Tianpeng; Chen, Lue; Wang, Mei; Ping, Jinsong

2018-02-01

The APOD (Atmospheric density detection and Precise Orbit Determination) is the first LEO (Low Earth Orbit) satellite in orbit co-located with a dual-frequency GNSS (GPS/BD) receiver, an SLR reflector, and a VLBI X/S dual band beacon. From the overlap statistics between consecutive solution arcs and the independent validation by SLR measurements, the orbit position deviation was below 10 cm before the on-board GNSS receiver got partially operational. In this paper, the focus is on the VLBI observations to the LEO satellite from multiple geodetic VLBI radio telescopes, since this is the first implementation of a dedicated VLBI transmitter in low Earth orbit. The practical problems of tracking a fast moving spacecraft with current VLBI ground infrastructure were solved and strong interferometric fringes were obtained by cross-correlation of APOD carrier and DOR (Differential One-way Ranging) signals. The precision in X-band time delay derived from 0.1 s integration time of the correlator output is on the level of 0.1 ns. The APOD observations demonstrate encouraging prospects of co-location of multiple space geodetic techniques in space, as a first prototype.

Crustal motion studies in the southwest Pacific: Geodetic measurements of plate convergence in Tonga, Vanuatu and the Solomon Islands

NASA Astrophysics Data System (ADS)

Phillips, David A.

The southwest Pacific is one of the most tectonically dynamic regions on Earth. This research focused on crustal motion studies in three regions of active Pacific-Australia plate convergence in the southwest Pacific: Tonga, the New Hebrides (Vanuatu) and the Solomons Islands. In Tonga, new and refined velocity estimates based on more than a decade of Global Positioning System (GPS) measurements and advanced analysis techniques are much more accurate than previously reported values. Convergence rates of 80 to 165 mm/yr at the Tonga trench represent the fastest plate motions observed on Earth. For the first time, rotation of the Fiji platform relative to the Australian plate is observed, and anomalous deformation of the Tonga ridge was also detected. In the New Hebrides, a combined GPS dataset with a total time series of more than ten years led to new and refined velocity estimates throughout the island arc. Impingement of large bathymetric features has led to arc fragmentation, and four distinct tectonic segments are identified. The central New Hebrides arc segment is being shoved eastward relative to the rest of the arc as convergence is partitioned between the forearc (Australian plate) and the backarc (North Fiji Basin) boundaries due to impingement of the d'Entrecasteaux Ridge and associated Bougainville seamount. The southern New Hebrides arc converges with the Australian plate more rapidly than predicted due to backarc extension. The first measurements of convergence in the northern and southernmost arc segments were also made. In the Solomon Islands, a four-year GPS time series was used to generate the first geodetic estimates of crustal velocity in the New Georgia Group, with 57--84 mm/yr of Australia-Solomon motion and 19--39 mm/yr of Pacific-Solomon motion being observed. These velocities are 20--40% lower than predicted Australia-Pacific velocities. Two-dimensional dislocation models suggest that most of this discrepancy can be attributed to locking of the San Cristobal trench and elastic strain accumulation in the forearc. Anomalous motion at Simbo island is also observed.

Estimating snow depth in real time using unmanned aerial vehicles

NASA Astrophysics Data System (ADS)

Niedzielski, Tomasz; Mizinski, Bartlomiej; Witek, Matylda; Spallek, Waldemar; Szymanowski, Mariusz

2016-04-01

In frame of the project no. LIDER/012/223/L-5/13/NCBR/2014, financed by the National Centre for Research and Development of Poland, we elaborated a fully automated approach for estimating snow depth in real time in the field. The procedure uses oblique aerial photographs taken by the unmanned aerial vehicle (UAV). The geotagged images of snow-covered terrain are processed by the Structure-from-Motion (SfM) method which is used to produce a non-georeferenced dense point cloud. The workflow includes the enhanced RunSFM procedure (keypoint detection using the scale-invariant feature transform known as SIFT, image matching, bundling using the Bundler, executing the multi-view stereo PMVS and CMVS2 software) which is preceded by multicore image resizing. The dense point cloud is subsequently automatically georeferenced using the GRASS software, and the ground control points are borrowed from positions of image centres acquired from the UAV-mounted GPS receiver. Finally, the digital surface model (DSM) is produced which - to improve the accuracy of georeferencing - is shifted using a vector obtained through precise geodetic GPS observation of a single ground control point (GCP) placed on the Laboratory for Unmanned Observations of Earth (mobile lab established at the University of Wroclaw, Poland). The DSM includes snow cover and its difference with the corresponding snow-free DSM or digital terrain model (DTM), following the concept of the digital elevation model of differences (DOD), produces a map of snow depth. Since the final result depends on the snow-free model, two experiments are carried out. Firstly, we show the performance of the entire procedure when the snow-free model reveals a very high resolution (3 cm/px) and is produced using the UAV-taken photographs and the precise GCPs measured by the geodetic GPS receiver. Secondly, we perform a similar exercise but the 1-metre resolution light detection and ranging (LIDAR) DSM or DTM serves as the snow-free model. Thus, the main objective of the paper is to present the performance of the new procedure for estimating snow depth and to compare the two experiments.

Geodetic Infrastructure, Data, Education and Community Engagement in Response to Earthquakes and Other Geophysical Events: An Overview of UNAVCO Support Resources Plus Highlights from Recent Event Response

NASA Astrophysics Data System (ADS)

Phillips, D. A.; Meertens, C. M.; Mattioli, G. S.; Miller, M. M.; Charlevoix, D. J.; Maggert, D.; Hodgkinson, K. M.; Henderson, D. B.; Puskas, C. M.; Bartel, B. A.; Baker, S.; Blume, F.; Normandeau, J.; Feaux, K.; Galetzka, J.; Williamson, H.; Pettit, J.; Crosby, C. J.; Boler, F. M.

2015-12-01

UNAVCO responds to community requests for support during and following significant geophysical events such as earthquakes, volcanic activity, landslides, glacial and ice-sheet movements, unusual uplift or subsidence, extreme meteorological events, or other hazards. UNAVCO can also respond proactively to events in anticipation of community demand for relevant data, data products or other services. Recent major events to which UNAVCO responded include the 2015 M7.8 Nepal EQ, the 2014 M6.0 American Canyon (Napa) EQ, the 2014 M8.2 Chile EQ, the 2011 M9.0 Tohoku, Japan EQ and tsunami, the 2010 M8.8 Maule, Chile EQ, and the 2010 M7.0 Haiti EQ. UNAVCO provided geophysical event response support for 15 events in 2014 alone. UNAVCO event response resources include geodetic infrastructure, data, and education and community engagement. Specific support resources include: field engineering personnel; continuous and campaign GNSS/GPS station deployment; real-time and/or high rate field GNSS/GPS station upgrades or deployment; data communications and power systems deployment; tiltmeter, strainmeter, and borehole seismometer deployments; terrestrial laser scanning (TLS a.k.a. ground-based LiDAR); InSAR data support; education and community engagement assistance or products; data processing services; generation of custom GNSS/GPS or borehole data sets and products; equipment shipping and logistics coordination; and assistance with RAPID proposal preparation, budgeting, and submission. The most critical aspect of a successful event response is effective and efficient communication. To facilitate such communication, UNAVCO creates event response web pages describing the event and the support being provided, and in the case of major events also provides an online event response forum. These resources are shared broadly with the geophysical community through multiple dissemination strategies including social media of UNAVCO and partner organizations. We will provide an overview of resources available to the community from UNAVCO in response to events. We will also highlight examples of the infrastructure, data and data products, and education and community engagement support provided by UNAVCO for major recent events.

Geodetic Infrastructure in the Ibiza and Barcelona Harbours for Sea Level Monitoring

NASA Astrophysics Data System (ADS)

Martinez-Benjamin, J. J.; Gili, J.; Lopez, R.; Tapia, A.; Perez, B.; Pros, F.

2013-12-01

The presentation is directed to the description of the actual situation and relevant information of the geodetic infrastructure of Ibiza and Barcelona sites for sea level determination and contribution to regional sea level rise. Time series are being analysed for mean sea level variations www.puertos.es. .In the framework of a Spanish Space Project, the instrumentation of sea level measurements has been improved by providing the Barcelona site with a radar tide gauge Datamar 2000C from Geonica s.l. near an acoustic tide gauge. Puertos del Estado installed in 2007 a MIROS radar tide gauge and the Barcelona Harbour Authority a GPS referente station in the roof of the new Control Tower situated in the Energy Pier. The radar sensor is over the water surface, on a L-shaped structure which elevates it a few meters above the quay shelf. 1-min data are transmitted to the ENAGAS Control Center by cable and then sent each 1 min to Puertos del Estado by e-mail. There is a GPS station Leica Geosystems GRX1200 GG Pro and antenna 1202. Precision levelling has been made several times in the last two years because the tower is founded in reclaimed land. The measured settlement rate is about 1cm/year that may be could mask the values registered by the tide gauge. A description of the actual infrastructure at Ibiza harbour at Marina de Botafoch, is presented and its applications to sea level monitoring and altimeter calibration in support of the main CGPS at Ibiza harbour. It is described the geometrical precision levelling made in June 2013 between the radar tide gauge and the GPS station. In particular, the CGPS located at Ibiza harbour is essential for its application to the marine campaign Baleares 2013, near Ibiza island. The main objective is to determine the altimeter bias for Jason-2, about 9:09 UTC September 15, 2013, and Saral/AltiKa, about 05:30 UTC September 16, UTC. These activities has been received funding of the Ministerio de Ciencia e Innovacion under Spanish National Project CGL2009-13435/CLI.

Debris flow cartography using differential GNSS and Theodolite measurements

NASA Astrophysics Data System (ADS)

Khazaradze, Giorgi; Guinau, Marta; Calvet, Jaume; Furdada, Gloria; Victoriano, Ane; Génova, Mar; Suriñach, Emma

2016-04-01

The presented results form part of a CHARMA project, which pursues a broad objective of reducing damage caused by uncontrolled mass movements, such as rockfalls, snow avalanches and debris flows. Ultimate goal of the project is to contribute towards the establishment of new scientific knowledge and tools that can help in the design and creation of early warning systems. Here we present the specific results that deal with the application of differential GNSS and classical geodetic (e.g. theodolite) methods for mapping debris and torrential flows. Specifically, we investigate the Portainé stream located in the Pallars Sobirà region of Catalonia (Spain), in the eastern Pyrenees. In the last decade more than ten debris-flow type phenomena have affected the region, causing considerable economic losses. Since early 2014, we have conducted several field campaigns within the study area, where we have employed a multi-disciplinary approach, consisting of geomorphological, dendro-chronological and geodetic methods, in order to map the river bed and reconstruct the history of the extreme flooding and debris flow events. Geodetic studies included several approaches, using the classical and satellite based methods. The former consisted of angle and distance measurements between the Geodolite 502 total station and the reflecting prisms placed on top of the control points located within the riverbed. These type of measurements are precise, although present several disadvantages such as the lack of absolute coordinates that makes the geo-referencing difficult, as well as a relatively time-consuming process that involves two persons. For this reason, we have also measured the same control points using the differential GNSS system, in order to evaluate the feasibility of replacing the total station measurements with the GNSS. The latter measuring method is fast and can be conducted by one person. However, the fact that the study area is within the riverbed, often below the trees, limits the visibility of the satellites and thus, can result in meter-level errors while estimating the positions. We have conducted 2 measurements using various differential GNSS systems in March and in September of 2015. During these measurements we used Leica Viva GS14 receiver as a rover station, which was equipped with a GSM card to establish an internet connection in order to receive differential corrections from continuous GNSS networks. During the first campaign we have used the RTK positioning method using the SmartNet network (http://es.smartnet-eu.com) operated by Leica. This system had the advantage of transmitting differential corrections for GPS and GLONASS systems. During the second campaign, we have had an access to the ICGC (http://www.icc.cat) CatNet permanent GPS network, which only provides GPS satellite corrections. Here we present the analysis of the obtained precisions from these two RTK systems. Additionally, we have analyzed the geodetic data in a post-processing mode using the Leica Geo Office 8.4 software with IGS estimated final orbits. For this procedure, in addition to using the data from nearby CatNet CGPS stations, we have also used data from the base station(s) specifically setup near the study area during the campaign period. The work has been supported by the Spanish Ministry of Science and Innovation project CHARMA: CHAracterization and ContRol of MAss Movements. A Challenge for Geohazard Mitigation (CGL2013-40828-R) and RISKNAT group (2014GR/1243).

A Novel Sensor for Attitude Determination Using Global Positioning System Signals

NASA Technical Reports Server (NTRS)

Crassidis, John L.; Quinn, David A.; Markley, F. Landis; McCullough, Jon D.

1998-01-01

An entirely new sensor approach for attitude determination using Global Positioning System (GPS) signals is developed. The concept involves the use of multiple GPS antenna elements arrayed on a single sensor head to provide maximum GPS space vehicle availability. A number of sensor element configurations are discussed. In addition to the navigation function, the array is used to find which GPS space vehicles are within the field-of-view of each antenna element. Attitude determination is performed by considering the sightline vectors of the found GPS space vehicles together with the fixed boresight vectors of the individual antenna elements. This approach has clear advantages over the standard differential carrier-phase approach. First, errors induced by multipath effects can be significantly reduced or eliminated altogether. Also, integer ambiguity resolution is not required, nor do line biases need to be determined through costly and cumbersome self-surveys. Furthermore, the new sensor does not require individual antennas to be physically separated to form interferometric baselines to determine attitude. Finally, development potential of the new sensor is limited only by antenna and receiver technology development unlike the physical limitations of the current interferometric attitude determination scheme. Simulation results indicate that accuracies of about 1 degree (3 omega) are possible.

Rotation and strain rate of Sulawesi from geometrical velocity field

NASA Astrophysics Data System (ADS)

Sarsito, D. A.; Susilo, Simons, W. J. F.; Abidin, H. Z.; Sapiie, B.; Triyoso, W.; Andreas, H.

2017-07-01

One of methods that can be used to determine the tectonic deformation status is rate estimation from geometric rotation and strain using quantitative velocity data from GPS observations. Microplate Sulawesi region located in the zone of triple junction (Eurasia, Australia and Philippine Sea Plates) has very complex tectonic and seismic condition, which is why become very important to know its recent deformation status in order to study neo-tectonic and disaster mitigation. Deformation rate quantification is estimated in two parameters: rotation and geodetic strain rate of each GPS station Delaunay triangle in the study area. The analysis in this study is not done using the grids since there is no rheological information at location that can be used as the interpolation-extrapolation constraints. Our analysis reveals that Sulawesi is characterized by rapid rotation in several different domains and compression-strain pattern that varies depending on the type and boundary conditions of microplate. This information is useful for studying neo tectonic deformation status and earthquake disaster mitigation.

Slip pulse and resonance of the Kathmandu basin during the 2015 Gorkha earthquake, Nepal

NASA Astrophysics Data System (ADS)

Galetzka, J.; Melgar, D.; Genrich, J. F.; Geng, J.; Owen, S.; Lindsey, E. O.; Xu, X.; Bock, Y.; Avouac, J.-P.; Adhikari, L. B.; Upreti, B. N.; Pratt-Sitaula, B.; Bhattarai, T. N.; Sitaula, B. P.; Moore, A.; Hudnut, K. W.; Szeliga, W.; Normandeau, J.; Fend, M.; Flouzat, M.; Bollinger, L.; Shrestha, P.; Koirala, B.; Gautam, U.; Bhatterai, M.; Gupta, R.; Kandel, T.; Timsina, C.; Sapkota, S. N.; Rajaure, S.; Maharjan, N.

2015-09-01

Detailed geodetic imaging of earthquake ruptures enhances our understanding of earthquake physics and associated ground shaking. The 25 April 2015 moment magnitude 7.8 earthquake in Gorkha, Nepal was the first large continental megathrust rupture to have occurred beneath a high-rate (5-hertz) Global Positioning System (GPS) network. We used GPS and interferometric synthetic aperture radar data to model the earthquake rupture as a slip pulse ~20 kilometers in width, ~6 seconds in duration, and with a peak sliding velocity of 1.1 meters per second, which propagated toward the Kathmandu basin at ~3.3 kilometers per second over ~140 kilometers. The smooth slip onset, indicating a large (~5-meter) slip-weakening distance, caused moderate ground shaking at high frequencies (>1 hertz; peak ground acceleration, ~16% of Earth’s gravity) and minimized damage to vernacular dwellings. Whole-basin resonance at a period of 4 to 5 seconds caused the collapse of tall structures, including cultural artifacts.

Slip pulse and resonance of the Kathmandu basin during the 2015 Gorkha earthquake, Nepal.

PubMed

Galetzka, J; Melgar, D; Genrich, J F; Geng, J; Owen, S; Lindsey, E O; Xu, X; Bock, Y; Avouac, J-P; Adhikari, L B; Upreti, B N; Pratt-Sitaula, B; Bhattarai, T N; Sitaula, B P; Moore, A; Hudnut, K W; Szeliga, W; Normandeau, J; Fend, M; Flouzat, M; Bollinger, L; Shrestha, P; Koirala, B; Gautam, U; Bhatterai, M; Gupta, R; Kandel, T; Timsina, C; Sapkota, S N; Rajaure, S; Maharjan, N

2015-09-04

Detailed geodetic imaging of earthquake ruptures enhances our understanding of earthquake physics and associated ground shaking. The 25 April 2015 moment magnitude 7.8 earthquake in Gorkha, Nepal was the first large continental megathrust rupture to have occurred beneath a high-rate (5-hertz) Global Positioning System (GPS) network. We used GPS and interferometric synthetic aperture radar data to model the earthquake rupture as a slip pulse ~20 kilometers in width, ~6 seconds in duration, and with a peak sliding velocity of 1.1 meters per second, which propagated toward the Kathmandu basin at ~3.3 kilometers per second over ~140 kilometers. The smooth slip onset, indicating a large (~5-meter) slip-weakening distance, caused moderate ground shaking at high frequencies (>1 hertz; peak ground acceleration, ~16% of Earth's gravity) and minimized damage to vernacular dwellings. Whole-basin resonance at a period of 4 to 5 seconds caused the collapse of tall structures, including cultural artifacts. Copyright © 2015, American Association for the Advancement of Science.

Space geodetic observation of expansion of the San Gabriel Valley, California, aquifer system, during heavy rainfall in winter 2004-2005

USGS Publications Warehouse

King, N.E.; Argus, D.; Langbein, J.; Agnew, D.C.; Bawden, G.; Dollar, R.S.; Liu, Z.; Galloway, D.; Reichard, E.; Yong, A.; Webb, F.H.; Bock, Y.; Stark, K.; Barseghian, D.

2007-01-01

Starting early in 2005, the positions of GPS stations in the San Gabriel valley region of southern California showed statistically significant departures from their previous behavior. Station LONG moved up by about 47 mm, and nearby stations moved away from LONG by about 10 mm. These changes began during an extremely rainy season in southern California and coincided with a 16-m increase in water level at a nearby well in Baldwin Park and a regional uplift detected by interferometric synthetic aperture radar. No equivalent signals were seen in GPS station position time series elsewhere in southern California. Our preferred explanation, supported by the timing and by a hydrologic simulation, is deformation due to recharging of aquifers after near-record rainfall in 2004-2005. We cannot rule out an aseismic slip event, but we consider such an event unlikely because it requires slip on multiple faults and predicts other signals that are not observed. Copyright 2007 by the American Geophysical Union.

The 2014 Mw6.9 Gokceada and 2017 Mw6.3 Lesvos Earthquakes in the Northern Aegean Sea: The Transition from Right-Lateral Strike-Slip Faulting on the North Anatolian Fault to Extension in the Central Aegean

NASA Astrophysics Data System (ADS)

Cetin, S.; Konca, A. O.; Dogan, U.; Floyd, M.; Karabulut, H.; Ergintav, S.; Ganas, A.; Paradisis, D.; King, R. W.; Reilinger, R. E.

2017-12-01

The 2014 Mw6.9 Gokceada (strike-slip) and 2017 Mw6.3 Lesvos (normal) earthquakes represent two of the set of faults that accommodate the transition from right-lateral strike-slip faulting on the North Anatolian Fault (NAF) to normal faulting along the Gulf of Corinth. The Gokceada earthquake was a purely strike-slip event on the western extension of the NAF where it enters the northern Aegean Sea. The Lesvos earthquake, located roughly 200 km south of Gokceada, occurred on a WNW-ESE-striking normal fault. Both earthquakes respond to the same regional stress field, as indicated by their sub-parallel seismic tension axis and far-field coseismic GPS displacements. Interpretation of GPS-derived velocities, active faults, crustal seismicity, and earthquake focal mechanisms in the northern Aegean indicates that this pattern of complementary faulting, involving WNW-ESE-striking normal faults (e.g. Lesvos earthquake) and SW-NE-striking strike-slip faults (e.g. Gokceada earthquake), persists across the full extent of the northern Aegean Sea. The combination of these two "families" of faults, combined with some systems of conjugate left-lateral strike-slip faults, complement one another and culminate in the purely extensional rift structures that form the large Gulfs of Evvia and Corinth. In addition to being consistent with seismic and geodetic observations, these fault geometries explain the increasing velocity of the southern Aegean and Peloponnese regions towards the Hellenic subduction zone. Alignment of geodetic extension and seismic tension axes with motion of the southern Aegean towards the Hellenic subduction zone suggests a direct association of Aegean extension with subduction, possibly by trench retreat, as has been suggested by prior investigators.

NChina16: A stable geodetic reference frame for geological hazard studies in north China

NASA Astrophysics Data System (ADS)

Wang, G.; Yan, B.; Gan, W.; Geng, J.

2017-12-01

This study established a stable North China Reference Frame 2016 (NChina16) using five years of continuous GPS observations (2011.8 to 2016.8) from 12 continuously operating reference stations (CORS) fixed to the stable interior of the North China Craton. Applications of NChina16 in landslide, subsidence, and post-seismic displacement studies are illustrated. The primary result of this study is the seven parameters for transforming Cartesian ECEF (Earth-Centered, Earth-Fixed) coordinates X, Y, and Z from the International GNSS Service Reference Frame 2008 (IGS08) to NChina16. The seven parameters include the epoch that is used to tie the regional reference frame to IGS08 and the time derivatives of three translations and three rotations. A method for developing a regional geodetic reference frame is introduced in detail. The GIPSY-OASIS (V6.4) software package was used to obtain the precise point positioning (PPP) time series with respect to IGS08. The stability (accuracy) of NChina16 is about 0.5 mm/year in both vertical and horizontal directions. This study also developed a regional seasonal model for correcting vertical displacement time series data derived from the PPP solutions. Long-term GPS observations (1999-2016) from five CORS in north China were used to develop the seasonal model. According to this study, the PPP daily solutions with respect to NChina16 could achieve 2-3 mm horizontal accuracy and 4-5 mm vertical accuracy after being modified by the regional model. NChina16 will be critical to the long-term landslide, subsidence, fault, and structural monitoring in north China and for ongoing post-seismic crustal deformation studies in Japan. NChina16 will be incrementally improved and synchronized with the IGS reference frame update.

What role did the Hikurangi subduction zone play in the M7.8 Kaikoura earthquake?

NASA Astrophysics Data System (ADS)

Wallace, L. M.; Hamling, I. J.; Kaneko, Y.; Fry, B.; Clark, K.; Bannister, S. C.; Ellis, S. M.; Francois-Holden, C.; Hreinsdottir, S.; Mueller, C.

2017-12-01

The 2016 M7.8 Kaikoura earthquake ruptured at least a dozen faults in the northern South Island of New Zealand, within the transition from the Hikurangi subduction zone (in the North Island) to the transpressive Alpine Fault (in the central South Island). The role that the southern end of the Hikurangi subduction zone played (or did not play) in the Kaikoura earthquake remains one of the most controversial aspects of this spectacularly complex earthquake. Investigations using near-field seismological and geodetic data suggest a dominantly crustal faulting source for the event, while studies relying on teleseismic data propose that a large portion of the moment release is due to rupture of the Hikurangi subduction interface beneath the northern South Island. InSAR and GPS data also show that a large amount of afterslip (up to 0.5 m) occurred on the subduction interface beneath the crustal faults that ruptured in the M7.8 earthquake, during the months following the earthquake. Modeling of GPS velocities for the 20 year period prior to the earthquake indicate that interseismic coupling was occurring on the Hikurangi subduction interface beneath the northern South Island, in a similar location to the suggested coseismic and postseismic slip on the subduction interface. We will integrate geodetic, seismological, tsunami, and geological observations in an attempt to balance the seemingly conflicting views from local and teleseismic data regarding the role that the southern Hikurangi subduction zone played in the earthquake. We will also discuss the broader implications of the observed coseismic and postseismic deformation for understanding the kinematics of the southern termination of the Hikurangi subduction zone, and its role in the transition from subduction to strike-slip in the central New Zealand region.

A New Seismic Hazard Model for Mainland China

NASA Astrophysics Data System (ADS)

Rong, Y.; Xu, X.; Chen, G.; Cheng, J.; Magistrale, H.; Shen, Z. K.

2017-12-01

We are developing a new seismic hazard model for Mainland China by integrating historical earthquake catalogs, geological faults, geodetic GPS data, and geology maps. To build the model, we construct an Mw-based homogeneous historical earthquake catalog spanning from 780 B.C. to present, create fault models from active fault data, and derive a strain rate model based on the most complete GPS measurements and a new strain derivation algorithm. We divide China and the surrounding regions into about 20 large seismic source zones. For each zone, a tapered Gutenberg-Richter (TGR) magnitude-frequency distribution is used to model the seismic activity rates. The a- and b-values of the TGR distribution are calculated using observed earthquake data, while the corner magnitude is constrained independently using the seismic moment rate inferred from the geodetically-based strain rate model. Small and medium sized earthquakes are distributed within the source zones following the location and magnitude patterns of historical earthquakes. Some of the larger earthquakes are distributed onto active faults, based on their geological characteristics such as slip rate, fault length, down-dip width, and various paleoseismic data. The remaining larger earthquakes are then placed into the background. A new set of magnitude-rupture scaling relationships is developed based on earthquake data from China and vicinity. We evaluate and select appropriate ground motion prediction equations by comparing them with observed ground motion data and performing residual analysis. To implement the modeling workflow, we develop a tool that builds upon the functionalities of GEM's Hazard Modeler's Toolkit. The GEM OpenQuake software is used to calculate seismic hazard at various ground motion periods and various return periods. To account for site amplification, we construct a site condition map based on geology. The resulting new seismic hazard maps can be used for seismic risk analysis and management.

OASIS - ORBIT ANALYSIS AND SIMULATION SOFTWARE

NASA Technical Reports Server (NTRS)

Wu, S. C.

1994-01-01

The Orbit Analysis and Simulation Software, OASIS, is a software system developed for covariance and simulation analyses of problems involving earth satellites, especially the Global Positioning System (GPS). It provides a flexible, versatile and efficient accuracy analysis tool for earth satellite navigation and GPS-based geodetic studies. To make future modifications and enhancements easy, the system is modular, with five major modules: PATH/VARY, REGRES, PMOD, FILTER/SMOOTHER, and OUTPUT PROCESSOR. PATH/VARY generates satellite trajectories. Among the factors taken into consideration are: 1) the gravitational effects of the planets, moon and sun; 2) space vehicle orientation and shapes; 3) solar pressure; 4) solar radiation reflected from the surface of the earth; 5) atmospheric drag; and 6) space vehicle gas leaks. The REGRES module reads the user's input, then determines if a measurement should be made based on geometry and time. PMOD modifies a previously generated REGRES file to facilitate various analysis needs. FILTER/SMOOTHER is especially suited to a multi-satellite precise orbit determination and geodetic-type problems. It can be used for any situation where parameters are simultaneously estimated from measurements and a priori information. Examples of nonspacecraft areas of potential application might be Very Long Baseline Interferometry (VLBI) geodesy and radio source catalogue studies. OUTPUT PROCESSOR translates covariance analysis results generated by FILTER/SMOOTHER into user-desired easy-to-read quantities, performs mapping of orbit covariances and simulated solutions, transforms results into different coordinate systems, and computes post-fit residuals. The OASIS program was developed in 1986. It is designed to be implemented on a DEC VAX 11/780 computer using VAX VMS 3.7 or higher. It can also be implemented on a Micro VAX II provided sufficient disk space is available.

Activities, Animations, and Online Tools to Enable Undergraduate Student Learning of Geohazards, Climate Change, and Water Resources

NASA Astrophysics Data System (ADS)

Pratt-Sitaula, B. A.; Walker, B.; Douglas, B. J.; Cronin, V. S.; Funning, G.; Stearns, L. A.; Charlevoix, D.; Miller, M. M.

2017-12-01

The NSF-funded GEodesy Tools for Societal Issues (GETSI) project is developing teaching resources for use in introductory and majors-level courses, emphasizing a broad range of geodetic methods and data applied to societally important issues. The modules include a variety of hands-on activities, demonstrations, animations, and interactive online tools in order to facilitate student learning and engagement. A selection of these activities will be showcased at the AGU session. These activities and data analysis exercises are embedded in 4-6 units per module. Modules can take 2-3 weeks of course time total or individual units and activities can be selected and used over just 1-2 class periods. Existing modules are available online via serc.carleton.edu/getsi/ and include "Ice mass and sea level changes", "Imaging active tectonics with LiDAR and InSAR", "Measuring water resources with GPS, gravity, and traditional methods", "Surface process hazards", and "GPS, strain, and earthquakes". Modules, and their activities and demonstrations were designed by teams of faculty and content experts and underwent rigorous classroom testing and review using the process developed by the Science Education Resource Center's InTeGrate Project (serc.carleton.edu/integrate). All modules are aligned to Earth Science and Climate literacy principles. GETSI collaborating institutions are UNAVCO (which runs NSF's Geodetic Facility), Indiana University, and Mt San Antonio College. Initial funding came from NSF's TUES (Transforming Undergraduate Education in STEM). A second phase of funding from NSF IUSE (Improving Undergraduate STEM Education) is just starting and will fund another six modules (including their demonstrations, activities, and hands-on activities) as well as considerably more instructor professional development to facilitate implementation and use.

Geodesy cannot presently detect the up-dip limit of frictional locking on megathrusts

NASA Astrophysics Data System (ADS)

Almeida, R. V.; Lindsey, E. O.; Bradley, K.; Hubbard, J.; Sathiakumar, S.; Malick, R.; Hill, E.

2017-12-01

Most discussions of interseismic behavior on megathrust faults focus on whether they are frictionally locked or creeping. Unfortunately, many geodetic studies of subduction zone megathrusts equate fault coupling with frictional locking. This comparison is not appropriate, as one reflects the physical properties of the fault, and the other reflects the kinematics of the fault. Much of the uncertainty about slip behavior is because in subduction zones, the shallow part of the fault is far from land, and therefore creep is not detectable by land-based GPS. Published coupling maps of subduction zone megathrusts often assume a low coupling ratio near the trench, updip from fully coupled regions. Yet, if the megathrust attains a coupling ratio of 1 anywhere on the fault (i.e., the hanging wall is moving with the same velocity as the footwall), a lower value of coupling updip of this location requires interseismic extension at a rate proportional to the decrease (Wang and Dixon, 2004). We argue that the shallow region of megathrusts lie in updip stress shadows, and do not (except under rare circumstances) experience appropriate driving forces to cause significant creep during the interseismic period. Therefore it may not be possible to determine whether these regions are frictionally locked by examining interseismic geodetic records. We demonstrate this effect using a boundary element model with rate-strengthening friction and a simplified subduction zone geometry. We show that a coupling value of zero at the trench is physically unrealistic even if only a small portion of the downdip fault zone is locked. The maximum creep at the trench depends on the width of the transition of the frictionally locked zone, but should be small (<30% of plate rate) under most circumstances. During the interseismic period, even if the shallow parts of megathrusts are frictionally unlocked, creep is likely smaller than the resolution of current seafloor geodetic techniques (which is currently in the range of cms/yr). These results have important implications for various aspects of subduction studies, including physical limits on geodetic coupling inversions, the hazard posed by slip on shallow decollements (tsunamigenic or otherwise), the seismotectonic interpretation of shallow seismicity, and the utility of seafloor geodetic measurements.

E-GRASP/Eratosthenes: GRGS numerical simulations and millimetric TRF realization

NASA Astrophysics Data System (ADS)

Pollet, A.; Coulot, D.; Biancale, R.; Mandea, M.

2017-12-01

To accurately measuring and understanding changes in sea level, ice sheets and other elements of the dynamic Earth system, a stable Terrestrial Reference Frame (TRF) is needed. To reach the goals for the TRF realization of 1 mm accuracy and 0.1 mm/year stability (GGOS, Meeting the Requirements of a Global Society on a Changing Planet in 2020, Plag and Pearlman, 2009), The European - Geodetic Reference Antenna in Space (E-GRASP) has been recently proposed to the ESA EE9 call. This space mission is designed to build an enduring and stable TRF, by carrying very precise sensor systems for all the key geodetic techniques used to define and monitor the TRF (DORIS, GNSS, SLR and VLBI).In this study, we present the numerical simulations carried out by the French Groupe de Recherche en Géodésie Spatiale (GRGS). We simulated the measurements of the four geodetic techniques (DORIS and SLR measurements to E-GRASP, VLBI interferometric measurements on E-GRASP and GPS measurements from ground stations and from E-GRASP) over five years. Next, we have evaluated the expected exactitude and stability of the TRF provided by the processing of these measurements. In addition, we show the expected impact of the on-board instrument calibration on the TRF. Finally, we simulated the measurements of the two LAGEOS and four DORIS satellites, quasars for VLBI and we computed two multi-technique combinations, one with E-GRASP measurements and one without, to evaluate the contribution of this satellite to a combination.

Global Simultaneous Estimation of Present-Day Surface Mass Trend and GIA Using Multi-Sensor Geodetic Data Combination

NASA Astrophysics Data System (ADS)

Wu, X.; Heflin, M. B.; Schotman, H.; Vermeersen, B. L.; Dong, D.; Gross, R. S.; Ivins, E. R.; Moore, A. W.; Owen, S. E.

2009-12-01

Separating geodetic signatures of present-day surface mass trend and Glacial Isostatic Adjustment (GIA) requires multi-data types of different physical characteristics. We take a kinematic approach to the global simultaneous estimation problem. Three sets of global spherical harmonic coefficients from degree 1 to 60 of the present-day surface mass trend, vertical and horizontal GIA induced surface velocity fields, as well as rotation vectors of 15 major tectonic plates are solved for. The estimation is carried out using GRACE geoid trend, 3-dimensional velocities measured at 664 SLR/VLBI/GPS sites, the data-assimilated JPL ECCO ocean model. The ICE-5G/IJ05 (VM2) predictions are used as a priori GIA mean model. An a priori covariance matrix is constructed in the spherical harmonic domain for the GIA model by propagating the covariance matrices of random and geographically correlated ice thickness errors and upper/lower mantle viscosity errors so that the resulting magnitude and geographic pattern of the geoid uncertainties roughly reflect the difference between two recent GIA models. Unprecedented high-precision results are achieved. For example, geocenter velocities due to present-day surface mass trend and due to GIA are both determined to uncertainties of better than 0.1 mm/yr without using direct geodetic geocenter information. Information content of the data sets, future improvements, and benefits from new data will also be explored in the global inverse framework.

Probabilistic Seismic Hazard Maps for Ecuador

NASA Astrophysics Data System (ADS)

Mariniere, J.; Beauval, C.; Yepes, H. A.; Laurence, A.; Nocquet, J. M.; Alvarado, A. P.; Baize, S.; Aguilar, J.; Singaucho, J. C.; Jomard, H.

2017-12-01

A probabilistic seismic hazard study is led for Ecuador, a country facing a high seismic hazard, both from megathrust subduction earthquakes and shallow crustal moderate to large earthquakes. Building on the knowledge produced in the last years in historical seismicity, earthquake catalogs, active tectonics, geodynamics, and geodesy, several alternative earthquake recurrence models are developed. An area source model is first proposed, based on the seismogenic crustal and inslab sources defined in Yepes et al. (2016). A slightly different segmentation is proposed for the subduction interface, with respect to Yepes et al. (2016). Three earthquake catalogs are used to account for the numerous uncertainties in the modeling of frequency-magnitude distributions. The hazard maps obtained highlight several source zones enclosing fault systems that exhibit low seismic activity, not representative of the geological and/or geodetical slip rates. Consequently, a fault model is derived, including faults with an earthquake recurrence model inferred from geological and/or geodetical slip rate estimates. The geodetical slip rates on the set of simplified faults are estimated from a GPS horizontal velocity field (Nocquet et al. 2014). Assumptions on the aseismic component of the deformation are required. Combining these alternative earthquake models in a logic tree, and using a set of selected ground-motion prediction equations adapted to Ecuador's different tectonic contexts, a mean hazard map is obtained. Hazard maps corresponding to the percentiles 16 and 84% are also derived, highlighting the zones where uncertainties on the hazard are highest.

GPS measurements of deformation associated with the 1987 Superstition Hills earthquake: Evidence for conjugate faulting

NASA Technical Reports Server (NTRS)

Larsen, Shawn; Reilinger, Robert; Neugebauer, Helen; Strange, William

1991-01-01

Large station displacements observed from Imperial Valley Global Positioning System (GPS) campaigns are attributed to the November 24, 1987 Superstition Hills earthquake sequence. Thirty sites from a 42 station GPS network established in 1986 were reoccupied during 1988 and/or 1990. Displacements at three sites within 3 kilometers of the surface rupture approach 0.5 m. Eight additional stations within 20 km of the seismic zone are displaced at least 10 cm. This is the first occurrence of a large earthquake (M(sub S) 6.6) within a preexisting GPS network. Best-fitting uniform slip models of rectangular dislocations in an elastic half-space indicate 130 + or - 8 cm right-lateral displacement along the northwest-trending Superstition Hills fault and 30 + or - 10 cm left-lateral displacement along the conjugate northeast-trending Elmore Ranch fault. The geodetic moments are 9.4 x 10(exp 25) dyne-cm and 2.3 x 10(exp 25) dyne-cm for the Superstition Hills and Elmore Ranch faults, respectively, consistent with teleseismic source parameters. The data also suggest the post seismic slip along the Superstition Hills fault is concentrated at shallow depths. Distributed slip solutions using Singular Value Decomposition indicate near uniform displacement along the Elmore Ranch fault and concentrated slip to the northwest and southeast along the Superstition Hills fault. A significant component of non-seismic displacement is observed across the Imperial Valley, which is attributed in part to interseismic plate-boundary deformation.

Rupture Characteristics of the 25 November 2016 Aketao Earthquake ( M w 6.6) in Eastern Pamir Revealed by GPS and Teleseismic Data

NASA Astrophysics Data System (ADS)

Li, Jie; Liu, Gang; Qiao, Xuejun; Xiong, Wei; Wang, Xiaoqiang; Liu, Daiqin; Sun, Jianing; Yushan, Ailixiati; Yusan, Sulitan; Fang, Wei; Wang, Qi

2018-02-01

The 25 November 2016 Aketao, Xinjiang earthquake occurred on the northeastern margin of the Pamir plateau, rupturing the Muji fault on the northern segment of the Kongur Extensional System. We collected coseismic offsets at 7 GPS sites, which show that the fault experienced significate dextral slip with a near-field geodetic displacement of up to 12 cm along the strike. The joint inversion of GPS data and teleseismic P waveforms suggests a complex rupture pattern characterized by the unilateral propagation slip from the epicenter to the southeast for 60 km with a total seismic moment of 1.3 × 1019 Nm, corresponding to a magnitude of M w 6.7 earthquake. Our model of slip distribution shows two major slip patches with a slip amplitude up to 0.6 m, one located at shallow depths of 0-8 km close to the hypocenter with apparent surface breaks and the other, 40 km to the southeast, buried at a greater depth of 12 km. The rupture is dominated by a right-lateral strike slip with significant normal-slip components. The near-field GPS data enhances the spatial resolution of source model. Based on the preferred slip model, the static Coulomb Failure Stress change caused by 2016 Aketao earthquake suggests that the unzipped western and eastern ends of Muji fault and the northern segment of Kungai Fault are significantly promoted.

GPS-derived Coseismic deformations of the 2016 Aktao Ms6.7 earthquake and source modelling

NASA Astrophysics Data System (ADS)

Li, J.; Zhao, B.; Xiaoqiang, W.; Daiqing, L.; Yushan, A.

2017-12-01

On 25th November 2016, a Ms6.7 earthquake occurred on Aktao, a county of Xinjiang, China. This earthquake was the largest earthquake occurred in the northeastern margin of the Pamir Plateau in the last 30 years. By GPS observation, we get the coseismic displacement of this earthquake. The maximum displacement site is located in the Muji Basin, 15km from south of the causative fault. The maximum deformation is down to 0.12m, and 0.10m for coseismic displacement, our results indicate that the earthquake has the characteristics of dextral strike-slip and normal-fault rupture. Based on the GPS results, we inverse the rupture distribution of the earthquake. The source model is consisted of two approximate independent zones with a depth of less than 20km, the maximum displacement of one zone is 0.6m, the other is 0.4m. The total seismic moment is Mw6.6.1 which is calculated by the geodetic inversion. The source model of GPS-derived is basically consistent with that of seismic waveform inversion, and is consistent with the surface rupture distribution obtained from field investigation. According to our inversion calculation, the recurrence period of strong earthquakes similar to this earthquake should be 30 60 years, and the seismic risk of the eastern segment of Muji fault is worthy of attention. This research is financially supported by National Natural Science Foundation of China (Grant No.41374030)

Characteristics and Limitations of Submerged GPS L1 Observations

NASA Astrophysics Data System (ADS)

Steiner, Ladina; Geiger, Alain

2017-04-01

Extensive amount of water stored in snow covers has a high impact on flood development during snow melting periods. Early assessment of these parameters in mountain environments enhance early-warning and thus prevention of major impacts. Sub-snow GNSS techniques are lately suggested to determine liquid water content, snow water equivalent or considered for avalanche rescue. This technique is affordable, flexible, and provides accurate and continuous observations independent on weather conditions. However, the characteristics of GNSS observations for applications within a snow-pack still need to be further investigated. The magnitude of the main interaction processes involved for the GPS wavelength propagating through different layers of snow, ice or water is theoretically examined. Liquid water exerts the largest influence on GPS signal propagation through a snow-pack. Therefore, we focus on determining the characteristics of GNSS observables under water. An experiment was set-up to investigate the characteristics and limitations of submerged GPS observations using a pool, a level control by communicating pipes, a geodetic and a low-cost GPS antenna, and a water level sensor. The GPS antennas were placed into the water. The water level was increased daily by a step of two millimeters up to thirty millimeters above the antenna. Based on this experiment, the signal penetration depth, satellite availability, the attenuation of signal strength and the quality of solutions are analyzed. Our experimental results show an agreement with the theoretically derived attenuation parameter and signal penetration depth. The assumption of water as the limiting parameter for GPS observations within a snow-pack can be confirmed. Higher wetness in a snow-pack leads to less transmission, higher refraction, higher attenuation and thus a decreased penetration depth as well as a reduced quality of the solutions. In consequence, GPS applications within a snow-pack are heavily impacted by wetness which is even more pronounced during melting period. In this poster, we present a short introduction to the principle, explain the developed algorithms and show results of experiments dedicated to the signal propagation in water.

Tying the spectral ends of the M9.0 Tohoku-Oki earthquake sequence: High-frequency radiators and early quasi-static afterslip

NASA Astrophysics Data System (ADS)

Inbal, A.; Ampuero, J. P.; Avouac, J.; Lengliné, O.; Helmberger, D. V.

2012-12-01

The March 11, 2011 M9.0 Tohoku-Oki earthquake was recorded by dense seismological and geodetical networks deployed in Japan, as well as by a vast number of seismic stations worldwide. These observations allow us to study the properties of the subduction interface with unprecedented accuracy and resolution. Here we examine the spectral tails of the co- and post-seismic stages using local geodetic and seismological recordings. First, we study the details of high-frequency (HF) energy radiation during the rupture by using strong-motion recordings. Second, we jointly invert 1Hz GPS, ocean-bottom GPS and aftershock data for the spatio-temporal distribution of early afterslip. In order to constrain the spatial distribution of HF radiators we model waveform envelopes recorded by Kik-net borehole accelerometers located in northeastern Japan. We compute theoretical envelopes for waves traveling in a heterogeneous scattering medium, and invert for the location and amplitude of energy radiators for frequencies ranging from 1 to 16 Hz. Because the inversion is extremely sensitive to the response of individual sites, we adopt an empirical approach and iteratively separate the source and site terms from the stacked spectra of numerous events recorded by the network. The output response functions for each site are used to stabilize the inversion. Preliminary results are consistent with far-field observations and suggest that the HF energy emitted during the M9.0 event originated at the down-dip limit of the rupture zone. We apply waveform cross-correlation to identify repeating events within the aftershock sequence, and locate them by match-filtering their waveforms with known templates. Many of these events occur on seismic asperities loaded by the surrounding creep. We jointly invert the slip histories on these fault patches and the available GPS data for the spatio-temporal distribution of afterslip during the first few hours following the mainshock. We use the Principal Component Analysis Inversion Method to determine the time history of slip on the megathrust during seismic slip and aseismic afterslip. The eigenfunctions are constrained in an iterative process that incorporates the slip histories of seismic asperities. This approach allows documenting the seismic and aseismic phases in a self-consistent manner. The GPS-only inversion places most of the early afterslip east of the hypocenter up to the trench, an area that seemed to have undergone dynamic overshoot.

Tightly coupled integration of ionosphere-constrained precise point positioning and inertial navigation systems.

PubMed

Gao, Zhouzheng; Zhang, Hongping; Ge, Maorong; Niu, Xiaoji; Shen, Wenbin; Wickert, Jens; Schuh, Harald

2015-03-10

The continuity and reliability of precise GNSS positioning can be seriously limited by severe user observation environments. The Inertial Navigation System (INS) can overcome such drawbacks, but its performance is clearly restricted by INS sensor errors over time. Accordingly, the tightly coupled integration of GPS and INS can overcome the disadvantages of each individual system and together form a new navigation system with a higher accuracy, reliability and availability. Recently, ionosphere-constrained (IC) precise point positioning (PPP) utilizing raw GPS observations was proven able to improve both the convergence and positioning accuracy of the conventional PPP using ionosphere-free combined observations (LC-PPP). In this paper, a new mode of tightly coupled integration, in which the IC-PPP instead of LC-PPP is employed, is implemented to further improve the performance of the coupled system. We present the detailed mathematical model and the related algorithm of the new integration of IC-PPP and INS. To evaluate the performance of the new tightly coupled integration, data of both airborne and vehicle experiments with a geodetic GPS receiver and tactical grade inertial measurement unit are processed and the results are analyzed. The statistics show that the new approach can further improve the positioning accuracy compared with both IC-PPP and the tightly coupled integration of the conventional PPP and INS.

Report On Fiducial Points At The Space Geodesy Based Cagliari Astronomical Observatory

NASA Astrophysics Data System (ADS)

Banni, A.; Buffa, F.; Falchi, E.; Sanna, G.

At the present time two research groups are engaged to space-geodesy activities in Sardinia: a staff belonging to the Stazione Astronomica of Cagliari (SAC) and the To- pography Section of the Dipartimento di Ingegneria Strutturale (DIST) of the Cagliari University. The two groups have a share in international campaigns and services. The local structure, consists of permanent stations of satellite observation both on radio and laser techniques. Particularly in the Cagliari Observatory a Satellite Laser Ranging system runs with nearly daily, low, medium and high orbit satellite tracking capability (e. g. Topex, Ajisai, Lageos1/2, Glonass); up to this time the Cagliari laser station has contributed towards the following international campaigns/organizations. Besides in the Observatory's site a fixed GPS system, belonging the Italian Space Agency GPS- Network and to the IGS-Network; and a GPS+GLONASS system, acquired by DIST and belonging to the IGLOS are installed and managed. All the above stations are furnished with meteorological sensors with RINEX format data dissemination avail- ability. Moreover a new 64 meters dish radio telescope (Sardinian Radio Telescope), geodetic VLBI equipped, is under construction not long away from the Observatory. The poster fully shows the facilities and furnishes a complete report on the mark- ers eccentricities, allowing co-location of the different space techniques operating in Sardinia.

Satellite Geodetic Constraints On Earthquake Processes: Implications of the 1999 Turkish Earthquakes for Fault Mechanics and Seismic Hazards on the San Andreas Fault

NASA Technical Reports Server (NTRS)

Reilinger, Robert

2005-01-01

Our principal activities during the initial phase of this project include: 1) Continued monitoring of postseismic deformation for the 1999 Izmit and Duzce, Turkey earthquakes from repeated GPS survey measurements and expansion of the Marmara Continuous GPS Network (MAGNET), 2) Establishing three North Anatolian fault crossing profiles (10 sitedprofile) at locations that experienced major surface-fault earthquakes at different times in the past to examine strain accumulation as a function of time in the earthquake cycle (2004), 3) Repeat observations of selected sites in the fault-crossing profiles (2005), 4) Repeat surveys of the Marmara GPS network to continue to monitor postseismic deformation, 5) Refining block models for the Marmara Sea seismic gap area to better understand earthquake hazards in the Greater Istanbul area, 6) Continuing development of models for afterslip and distributed viscoelastic deformation for the earthquake cycle. We are keeping close contact with MIT colleagues (Brad Hager, and Eric Hetland) who are developing models for S. California and for the earthquake cycle in general (Hetland, 2006). In addition, our Turkish partners at the Marmara Research Center have undertaken repeat, micro-gravity measurements at the MAGNET sites and have provided us estimates of gravity change during the period 2003 - 2005.

Development of a new tubular buoy for seafloor geodetic observation with cabled system

NASA Astrophysics Data System (ADS)

Kido, M.; Osada, Y.; Fujimoto, H.; Kaneda, Y.

2008-12-01

Seafloor geodetic observation using the GPS/acoustic technique is now a practical tool to monitor crustal movement beneath the ocean. The DONET project, which plans to install a seafloor cable system and is promoted by MEXT, Japan is a promising candidate to achieve semi-realtime and long-term seafloor observation. However there still remain some technical problem for the system. One of the largest problem is the stability and safety of a mooring buoy for long-term. A box-type small buoy as a surface platform, which is out present system, heavily oscillates with ocean swells especially for short waves and has large friction against ocean current within water. To overcome this problem, we have developed a new buoy as a prototype of long-term mooring system. Since the new buoy is tubular in shape and more than 4 m height, its attitude at the sea surface is quite stable. A typical oscillating period is improved from 2 sec for the box-type buoy into more than 6 sec for the new tubular buoy. Further more, effect of multiple reflection against sea surface or bottom of the buoy is almost disappear due to its acoustic transducer locates at greater depth (around 3 m). We have confirmed that observed acoustic signals of the reply from seafloor transponders are quite clear and has small and symmetric siderobes in the correlogram, which is important for proper traveltime detection. The new buoy is designed as low power and remote controlled system, which is also suitable for future cable connection. Using this new system, we have conducted a test survey for several hours in Kumano-nada, along Nankai trough, where the seafloor cable is planed to be laid. At this site we have placed a seafloor transponders' array with five instruments rather than usual three transponders. This will help to estimate lateral gradient of sound speed structure in the ocean, which degrade positioning accuracy in the past survey and analytic styles. In this talk, we present the initial result of the survey using the new buoy.

GPS World, Innovation: Autonomous Navigation at High Earth Orbits

NASA Technical Reports Server (NTRS)

Bamford, William; Winternitz, Luke; Hay, Curtis

2005-01-01

Calculating a spacecraft's precise location at high orbital altitudes-22,000 miles (35,800 km) and beyond-is an important and challenging problem. New and exciting opportunities become possible if satellites are able to autonomously determine their own orbits. First, the repetitive task of periodically collecting range measurements from terrestrial antennas to high altitude spacecraft becomes less important-this lessens competition for control facilities and saves money by reducing operational costs. Also, autonomous navigation at high orbital altitudes introduces the possibility of autonomous station keeping. For example, if a geostationary satellite begins to drift outside of its designated slot it can make orbit adjustments without requiring commands from the ground. Finally, precise onboard orbit determination opens the door to satellites flying in formation-an emerging concept for many scientific space applications. The realization of these benefits is not a trivial task. While the navigation signals broadcast by GPS satellites are well suited for orbit and attitude determination at lower altitudes, acquiring and using these signals at geostationary (GEO) and highly elliptical orbits is much more difficult. The light blue trace describes the GPS orbit at approximately 12,550 miles (20,200 km) altitude. GPS satellites were designed to provide navigation signals to terrestrial users-consequently the antenna array points directly toward the earth. GEO and HE0 orbits, however, are well above the operational GPS constellation, making signal reception at these altitudes more challenging. The nominal beamwidth of a Block II/IIA GPS satellite antenna array is approximately 42.6 degrees. At GEO and HE0 altitudes, most of these primary beam transmissions are blocked by the Earth, leaving only a narrow region of nominal signal visibility near opposing limbs of the earth. This region is highlighted in gray. If GPS receivers at GEO and HE0 orbits were designed to use these higher power signals only, precise orbit determination would not be practical. Fortunately, the GPS satellite antenna array also produces side lobe signals at much lower power levels. NASA has designed and tested the Navigator, a new GPS receiver that can acquire and track these weaker signals, thereby dramatically increasing the signal visibility at these altitudes. While using much weaker signals is a fundamental requirement for a high orbital altitude GPS receiver, it is certainly not the only challenge. There are other unique characteristics of this application that must also be considered. For example, Position Dilution of Precision (PDOP) figures are much higher at GEO and HE0 altitudes because visible GPS satellites are concentrated in a much smaller area with respect to the spacecraft antenna. These poor PDOP values contribute considerable error to the point solutions calculated by the spacecraft GPS receiver. Finally, spacecraft GPS receivers must be designed to withstand a variety of extreme environmental conditions. Variations in acceleration between launch and booster separation are extreme. Temperature gradients in the space environment are also severe. Furthermore, radiation effects are a major concern-spacecraft-borne GPS receivers must be designed with radiation-hardened electronics to guard against this phenomenon, otherwise they simply will not work. Perhaps most importantly, there are no opportunities to repair or modify any space-borne GPS receiver after it has been launched. Great care must be taken to ensure all performance characteristics have been analyzed prior to liftoff.

Characterization of Periodic Variations in the GPS Satellite Clocks

DTIC Science & Technology

2008-08-08

la tin g th e M D EV . F or s at el lit es , t he le ge nd in di ca te s th e N av st ar v eh ic le n um be r/P R N c...10 Senior, Ray, and Beard Fi g. 3 — T im e- va ry in g am pl itu de s o f t he 1 2- ho ur (b la ck ), 6- ho ur (b lu e) , 4...Transfer and Time Scale Formation,” Metrologia 40, S270-S288. Ray, J.R., and K.L. Senior, 2005, “Geodetic

A strawman SLR program plan for the 1990s

NASA Technical Reports Server (NTRS)

Degnan, John J.

1994-01-01

A series of programmatic and technical goals for the satellite laser ranging (SLR) network are presented. They are: (1) standardize the performance of the global SLR network; (2) improve the geographic distribution of stations; (3) reduce costs of field operations and data processing; (4) expand the 24 hour temporal coverage to better serve the growing constellation of satellites; (5) improve absolute range accuracy to 2 mm at key stations; (6) improve satellite force, radiative propagation, and station motion models and investigate alternative geodetic analysis techniques; (7) support technical intercomparison and the Terrestrial Reference Frame through global collocations; (8) investigate potential synergisms between GPS and SLR.

PBO Nucleus Project Status: Integration of 209 Existing GPS Stations into the Plate Boundary Observatory.

NASA Astrophysics Data System (ADS)

Blume, F.; Prescott, W.; Anderson, G.; Eriksson, S.; Feldl, N.

2006-12-01

Tectonic and earthquake research in the US has experienced a quiet revolution over the last decade precipitated by the recognition that slow-motion faulting events can both trigger and be triggered by regular earthquakes. Transient motion has now been found in essentially all tectonic environments, and the detection and analysis of such events is the first-order science target of the EarthScope Project. Because of this and a host of other fundamental tectonics questions that can be answered only with long-duration geodetic time series, the incipient 1400-station EarthScope Plate Boundary Observatory (PBO) network has been designed to leverage 432 existing continuous GPS stations whose measurements extend back over a decade. The irreplaceable recording history of these stations is accelerating EarthScope scientific return by providing the highest possible resolution. This resolution will be used to detect and understand transients, to determine the three-dimensional velocity field (particularly vertical motion), and to improve measurement precision by understanding the complex noise sources inherent in GPS. The PBO Nucleus project supports the operation, maintenance and hardware upgrades of a subset of the six western U.S. geodetic networks until they are subsumed by PBO. Uninterrupted data flow from these stations will effectively double the time-series length of PBO over the expected life of EarthScope, and has created, for the first time, a single GPS-based geodetic network in the US. The other existing sites remain in operation under support from non-NSF sources (e.g. the USGS), and EarthScope continues to benefit from their continued operation. On the grounds of relevance to EarthScope science goals, geographic distribution and data quality, 209 of the 432 existing stations were selected as the nucleus upon which to build PBO. Conversion of these stations to a PBO-compatible mode of operation was begun under previous funding, and as a result data now flow directly to PBO archives and processing centers while maintenance, operations, and meta-data requirements are continuing to be upgraded to PBO standards. At the end of this project all 209 stations will be fully incorporated into PBO, meeting all standards for new PBO construction including data communications and land use permits. Funds for operation of these stations have been included in planned budgets for PBO after the construction phase ends and PBO begins an operational phase in 2008. To date approximately 150 of the 209 stations have been completely upgraded, and data flow from all stations is incorporated into the PBO data analysis flow. The community has only begun to understand the pervasive effects of transient creep, and its societal consequences remained largely unexplored. For example, one open question is whether slow faulting pervasively moderates earthquake nucleation. The existence of slow earthquakes will impact seismic hazards estimation, since these transients are now known to `absorb' a significant component of total slip in some regions and trigger earthquakes in others. The data from these stations serve a much larger audience than just the few people who work to keep them operating. This project is now collecting the data that will be used by the next generation of solid-earth researchers for at least two decades. Educational modules are being developed by a team of researchers, educators, and curriculum development professionals, and are being disseminated through regional and national workshops. An interactive website provides the newest developments in tectonics research to K-16 classrooms.

A Demonstration of GPS Landslide Monitoring Using Online Positioning User Service (OPUS)

NASA Astrophysics Data System (ADS)

Wang, G.

2011-12-01

Global Positioning System (GPS) technologies have been frequently applied to landslide study, both as a complement, and as an alternative to conventional surveying methods. However, most applications of GPS for landslide monitoring have been limited to the academic community for research purposes. High-accuracy GPS has not been widely equipped in geotechnical companies and used by technicians. The main issue that limits the applications of GPS in the practice of high-accuracy landslide monitoring is the complexity of GPS data processing. This study demonstrated an approach using the Online Positioning User Service (OPUS) (http://www.ngs.noaa.gov/OPUS) provided by the National Geodetic Survey (NGS) of National Oceanic and Atmospheric Administration (NOAA) to process GPS data and conduct long-term landslide monitoring in the Puerto Rico and Virgin Islands Region. Continuous GPS data collected at a creeping landslide site during two years were used to evaluate different scenarios for landslide surveying: continuous or campaign, long duration or short duration, morning or afternoon (different weather conditions). OPUS uses Continuously Operating Reference Station (CORS) managed by NGS (http://www.ngs.noaa.giv/CORS/) as references and user data as a rover to solve a position. There are 19 CORS permanent GPS stations in the Puerto Rico and Virgin Islands region. The dense GPS network provides a precise and reliable reference frame for subcentimeter-accuracy landslide monitoring in this region. Our criterion for the accuracy was the root-mean-square (RMS) of OPUS solutions over a 2-year period with respect to true landslide displacement time series overt the same period. The true landslide displacements were derived from a single-baseline (130 m) GPS processing by using 24-hour continuous data. If continuous GPS surveying is performed in the field, then OPUS static processing can provide 0.6 cm horizontal and 1.1 cm vertical precision with few outliers. If repeated campaign-style surveying is performed in the field, then the choice of observation time window and duration are very important. In order to detect a suspected sliding mass and track the kinematics of a creeping landslide, sub-centimeter horizontal accuracy is often required. OPUS static solutions for sessions of 4 hours or longer and OPUS rapid-static solutions for sessions as short as 15 minutes can achieve accuracy at this level if data collection during extreme weather conditions is avoided, such as rainfall and storm time. This study also indicated that rainfall events can seriously degrade the performance of high-accuracy GPS. Field GPS landslide surveying should avoid rainfall time that is usually accompanied by thunderstorms and the passage of weather fronts.

Better Aircraft Positioning for Airborne Gravimetry: Results from GRAV-D's "Kinematic GPS Challenge" Issued to the GPS Community

NASA Astrophysics Data System (ADS)

Diehl, T. M.; Mader, G. L.; Preaux, S. A.; Weil, C.

2011-12-01

The National Geodetic Survey's (NGS's) Gravity for the Redefinition of the American Vertical Datum (GRAV-D) program plans to collect airborne gravity data across the entire U.S. and its holdings over the next decade. The goal is to build a geoid accurate to 1-2 cm, for which the airborne gravity data is key. The first phase is underway, with > 13% of data collection already completed across the U.S. To achieve the best airborne gravity data accuracy possible, the GPS position solutions must provide not just accurate positions, but also accurate velocities and accelerations to be used in calculating the gravity corrections. However, to our knowledge, no comparison has been done of available kinematic GPS processing techniques as they pertain to producing accurate airborne gravity results. So, in Fall 2010, NGS issued the "Kinematic GPS Challenge" to the GPS processing community, soliciting position solutions for GPS data of two GRAV-D airborne gravity flights done in Louisiana in 2008. Of the four lines on these two flights, one of the lines on the first flight was noisy (due to excessive turbulence) and was reflown on the second flight. These two flights of data allow the Challenge results to be tested on both good-quality and noisy data, as well as to be compared for repeatability along the reflown line, the assumption being that the solution producing the best fit between the reflown gravity data is the best. Fifteen position results from nine contributors were submitted from the GPS community for each of the two flights. We will present the results of the Kinematic GPS Challenge in an anonymous manner, to provide information to the airborne gravity community while protecting the identities of the GPS contributors while they incorporate the results into their research projects. Initial analyses show that the submitted position solutions are somewhat different, usually by +/- 0.25 m or less in X, Y, and Z. The shape and structure of these differences indicate significant differences in the derived velocities and accelerations. Those differences are easily identifiable in the gravity anomalies calculated with those solutions. Several gravity solutions computed produce differences from the ensemble average of 2-3 mGal in places, though most were within +/- 1 mGal. An additional comparison was done with the current preferred NGS GPS+IMU solution (a loosely-coupled differential GPS+IMU solution from commercial software) versus the Challenge GPS-only solutions. The loosely coupled solution fared better in the noisy flight than the GPS only, but there was less significant difference in the calm weather flight. Our presentation will provide a comprehensive analysis of the Challenge results.

SLR tracking of GPS-35

NASA Technical Reports Server (NTRS)

Pavlis, Erricos C.

1994-01-01

An experiment was designed to launch a corner cube retroreflector array on one of the Global Positioning Satellites (GPS). The launch on Aug. 31, 1993 ushered in the era of SLR tracking of GPS spacecraft. Once the space operations group finished the check-out procedures for the new satellite, the agreed upon SLR sites were allowed to track it. The first site to acquire GPS-35 was the Russian system at Maidanak and closely after the MLRS system at McDonald Observatory, Texas. The laser tracking network is currently tracking the GPS spacecraft known as GPS-35 or PRN 5 with great success. From the NASA side there are five stations that contribute data regularly and nearly as many from the international partners. Upcoming modifications to the ground receivers will allow for a further increase in the tracking capabilities of several additional sites and add some desperately needed southern hemisphere tracking. We are analyzing the data and are comparing SLR-derived orbits to those determined on the basis of GPS radiometric data.

Global Plate Velocities from the Global Positioning System

NASA Technical Reports Server (NTRS)

Larson, Kristine M.; Freymueller, Jeffrey T.; Philipsen, Steven

1997-01-01

We have analyzed 204 days of Global Positioning System (GPS) data from the global GPS network spanning January 1991 through March 1996. On the basis of these GPS coordinate solutions, we have estimated velocities for 38 sites, mostly located on the interiors of the Africa, Antarctica, Australia, Eurasia, Nazca, North America, Pacific, and South America plates. The uncertainties of the horizontal velocity components range from 1.2 to 5.0 mm/yr. With the exception of sites on the Pacific and Nazca plates, the GPS velocities agree with absolute plate model predictions within 95% confidence. For most of the sites in North America, Antarctica, and Eurasia, the agreement is better than 2 mm/yr. We find no persuasive evidence for significant vertical motions (less than 3 standard deviations), except at four sites. Three of these four were sites constrained to geodetic reference frame velocities. The GPS velocities were then used to estimate angular velocities for eight tectonic plates. Absolute angular velocities derived from the GPS data agree with the no net rotation (NNR) NUVEL-1A model within 95% confidence except for the Pacific plate. Our pole of rotation for the Pacific plate lies 11.5 deg west of the NNR NUVEL-1A pole, with an angular speed 10% faster. Our relative angular velocities agree with NUVEL-1A except for some involving the Pacific plate. While our Pacific-North America angular velocity differs significantly from NUVEL-1A, our model and NUVEL-1A predict very small differences in relative motion along the Pacific-North America plate boundary itself. Our Pacific-Australia and Pacific- Eurasia angular velocities are significantly faster than NUVEL-1A, predicting more rapid convergence at these two plate boundaries. Along the East Pacific Pise, our Pacific-Nazca angular velocity agrees in both rate and azimuth with NUVFL-1A.

Long range geoid control through the European GPS traverse: Final results

NASA Technical Reports Server (NTRS)

Torge, W.; Basic, T.; Denker, H.; Doliff, J.; Wenzel, H.-G.

1989-01-01

The European north-south Global Positioning System (GPS)-traverse proposed by IAG SSG 3.88, should control and improve the European geoid. This traverse follows first order leveling lines, included in the United European Leveling Network. From May to August 1986 and in July 1987, the central and northern part of this traverse (approx. 3000 km) was observed using up to four TI 4100 receivers, covering Austria, Federal Republic of Germany, Denmark, Sweden and Norway. Both traverse parts contain 71 stations with distances of about 50 km. In addition, 8 stations have been occupied for overlapping connections, and traverse links were established for connecting the fundamental stations Wettzell (VLBI and SLR) and Onsala (VLBI). Final results show a GPS observation precision of a few cm for loops of some 100 km circumference. After transformation of the GPS results to geoid heights using the leveled heights, comparisons with different existing gravimetric geoid determinations including geopotential models were performed. In addition, new geopotential models complete to degree and order 360 tailored to gravity data in Europe, and gravimetric geoid solutions using 6 x 10' mean gravity anomalies were investigated. The comparison with GPS and leveling yields rms discrepancies of + or - 0.1...0.2 m over 1000 km traverse sections for the best solutions, but a strong slope is existing in Sweden and southern Norway in almost all solutions, which is probably caused by systematic errors in the available gravity data for Scandinavia. This is confirmed by a new geoid computation at the Danish Geodetic Institute where the slope has disappeared. If this new solution is taken for the northern traverse section and the best solution for the central part, the rms discrepancy reduces to approximately + or - 0.2 m over 3000 km. Thus, a + or - 10 (exp 7) relative height accuracy seems to be achievable over long distances with the GPS/leveling and the gravimetric geoid calculation techniques, applied in this experiment.

Cansiglio Karst Plateau: 10 Years of Geodetic-Hydrological Observations in Seismically Active Northeast Italy

NASA Astrophysics Data System (ADS)

Grillo, Barbara; Braitenberg, Carla; Nagy, Ildikó; Devoti, Roberto; Zuliani, David; Fabris, Paolo

2018-04-01

Ten years' geodetic observations (2006-2016) in a natural cave of the Cansiglio Plateau (Bus de la Genziana), a limestone karstic area in northeastern Italy, are discussed. The area is of medium-high seismic risk: a strong earthquake in 1936 below the plateau (M m = 6.2) and the 1976 disastrous Friuli earthquake (M m = 6.5) are recent events. At the foothills of the karstic massif, three springs emerge, with average flow from 5 to 10 m3/s, and which are the sources of a river. The tiltmeter station is set in a natural cavity that is part of a karstic system. From March 2013, a multiparametric logger (temperature, stage, electrical conductivity) was installed in the siphon at the bottom of the cave to discover the underground hydrodynamics. The tilt records include signals induced by hydrologic and tectonic effects. The tiltmeter signals have a clear correlation to the rainfall, the discharge series of the river and the data recorded by multiparametric loggers. Additionally, the data of a permanent GPS station located on the southern slopes of the Cansiglio Massif (CANV) show also a clear correspondence with the river level. The fast water infiltration into the epikarst, closely related to daily rainfall, is distinguished in the tilt records from the characteristic time evolution of the karstic springs, which have an impulsive level increase with successive exponential decay. It demonstrates the usefulness of geodetic measurements to reveal the hydrological response of the karst. One outcome of the work is that the tiltmeters can be used as proxies for the presence of flow channels and the pressure that builds up due to the water flow. With 10 years of data, a new multidisciplinary frontier was opened between the geodetic studies and the karstic hydrogeology to obtain a more complete geologic description of the karst plateau.

Effects of crustal layering on source parameter inversion from coseismic geodetic data

NASA Astrophysics Data System (ADS)

Amoruso, A.; Crescentini, L.; Fidani, C.

2004-10-01

We study the effect of a superficial layer overlying a half-space on the surface displacements caused by uniform slipping of a dip-slip normal rectangular fault. We compute static coseismic displacements using a 3-D analytical code for different characteristics of the layered medium, different fault geometries and different configurations of bench marks to simulate different kinds of geodetic data (GPS, Synthetic Aperture Radar, and levellings). We perform both joint and separate inversions of the three components of synthetic displacement without constraining fault parameters, apart from strike and rake, and using a non-linear global inversion technique under the assumption of homogeneous half-space. Differences between synthetic displacements computed in the presence of the superficial soft layer and in a homogeneous half-space do not show a simple regular behaviour, even if a few features can be identified. Consequently, also retrieved parameters of the homogeneous equivalent fault obtained by unconstrained inversion of surface displacements do not show a simple regular behaviour. We point out that the presence of a superficial layer may lead to misestimating several fault parameters both using joint and separate inversions of the three components of synthetic displacement and that the effects of the presence of the superficial layer can change whether all fault parameters are left free in the inversions or not. In the inversion of any kind of coseismic geodetic data, fault size and slip can be largely misestimated, but the product (fault length) × (fault width) × slip, which is proportional to the seismic moment for a given rigidity modulus, is often well determined (within a few per cent). Because inversion of coseismic geodetic data assuming a layered medium is impracticable, we suggest that only a case-to-case study involving some kind of recursive determination of fault parameters through data correction seems to give the proper approach when layering is important.

Cansiglio Karst Plateau: 10 Years of Geodetic-Hydrological Observations in Seismically Active Northeast Italy

NASA Astrophysics Data System (ADS)

Grillo, Barbara; Braitenberg, Carla; Nagy, Ildikó; Devoti, Roberto; Zuliani, David; Fabris, Paolo

2018-05-01

Ten years' geodetic observations (2006-2016) in a natural cave of the Cansiglio Plateau (Bus de la Genziana), a limestone karstic area in northeastern Italy, are discussed. The area is of medium-high seismic risk: a strong earthquake in 1936 below the plateau ( M m = 6.2) and the 1976 disastrous Friuli earthquake ( M m = 6.5) are recent events. At the foothills of the karstic massif, three springs emerge, with average flow from 5 to 10 m3/s, and which are the sources of a river. The tiltmeter station is set in a natural cavity that is part of a karstic system. From March 2013, a multiparametric logger (temperature, stage, electrical conductivity) was installed in the siphon at the bottom of the cave to discover the underground hydrodynamics. The tilt records include signals induced by hydrologic and tectonic effects. The tiltmeter signals have a clear correlation to the rainfall, the discharge series of the river and the data recorded by multiparametric loggers. Additionally, the data of a permanent GPS station located on the southern slopes of the Cansiglio Massif (CANV) show also a clear correspondence with the river level. The fast water infiltration into the epikarst, closely related to daily rainfall, is distinguished in the tilt records from the characteristic time evolution of the karstic springs, which have an impulsive level increase with successive exponential decay. It demonstrates the usefulness of geodetic measurements to reveal the hydrological response of the karst. One outcome of the work is that the tiltmeters can be used as proxies for the presence of flow channels and the pressure that builds up due to the water flow. With 10 years of data, a new multidisciplinary frontier was opened between the geodetic studies and the karstic hydrogeology to obtain a more complete geologic description of the karst plateau.

Millimeter accuracy satellites for two color ranging

NASA Technical Reports Server (NTRS)

Degnan, John J.

1993-01-01

The principal technical challenge in designing a millimeter accuracy satellite to support two color observations at high altitudes is to provide high optical cross-section simultaneously with minimal pulse spreading. In order to address this issue, we provide, a brief review of some fundamental properties of optical retroreflectors when used in spacecraft target arrays, develop a simple model for a spherical geodetic satellite, and use the model to determine some basic design criteria for a new generation of geodetic satellites capable of supporting millimeter accuracy two color laser ranging. We find that increasing the satellite diameter provides: a larger surface area for additional cube mounting thereby leading to higher cross-sections; and makes the satellite surface a better match for the incoming planar phasefront of the laser beam. Restricting the retroreflector field of view (e.g. by recessing it in its holder) limits the target response to the fraction of the satellite surface which best matches the optical phasefront thereby controlling the amount of pulse spreading. In surveying the arrays carried by existing satellites, we find that European STARLETTE and ERS-1 satellites appear to be the best candidates for supporting near term two color experiments in space.

Nanosecond-level time synchronization of autonomous radio detector stations for extensive air showers

NASA Astrophysics Data System (ADS)

The Pierre Auger Collaboration

2016-01-01

To exploit the full potential of radio measurements of cosmic-ray air showers at MHz frequencies, a detector timing synchronization within 1 ns is needed. Large distributed radio detector arrays such as the Auger Engineering Radio Array (AERA) rely on timing via the Global Positioning System (GPS) for the synchronization of individual detector station clocks. Unfortunately, GPS timing is expected to have an accuracy no better than about 5 ns. In practice, in particular in AERA, the GPS clocks exhibit drifts on the order of tens of ns. We developed a technique to correct for the GPS drifts, and an independent method is used to cross-check that indeed we reach a nanosecond-scale timing accuracy by this correction. First, we operate a ``beacon transmitter'' which emits defined sine waves detected by AERA antennas recorded within the physics data. The relative phasing of these sine waves can be used to correct for GPS clock drifts. In addition to this, we observe radio pulses emitted by commercial airplanes, the position of which we determine in real time from Automatic Dependent Surveillance Broadcasts intercepted with a software-defined radio. From the known source location and the measured arrival times of the pulses we determine relative timing offsets between radio detector stations. We demonstrate with a combined analysis that the two methods give a consistent timing calibration with an accuracy of 2 ns or better. Consequently, the beacon method alone can be used in the future to continuously determine and correct for GPS clock drifts in each individual event measured by AERA.

Nanosecond-level time synchronization of autonomous radio detector stations for extensive air showers

DOE PAGES

Aab, Alexander

2016-01-29

To exploit the full potential of radio measurements of cosmic-ray air showers at MHz frequencies, a detector timing synchronization within 1 ns is needed. Large distributed radio detector arrays such as the Auger Engineering Radio Array (AERA) rely on timing via the Global Positioning System (GPS) for the synchronization of individual detector station clocks. Unfortunately, GPS timing is expected to have an accuracy no better than about 5 ns. In practice, in particular in AERA, the GPS clocks exhibit drifts on the order of tens of ns. We developed a technique to correct for the GPS drifts, and an independentmore » method used for cross-checks that indeed we reach nanosecond-scale timing accuracy by this correction. First, we operate a “beacon transmitter” which emits defined sine waves detected by AERA antennas recorded within the physics data. The relative phasing of these sine waves can be used to correct for GPS clock drifts. In addition to this, we observe radio pulses emitted by commercial airplanes, the position of which we determine in real time from Automatic Dependent Surveillance Broadcasts intercepted with a software-defined radio. From the known source location and the measured arrival times of the pulses we determine relative timing offsets between radio detector stations. We demonstrate with a combined analysis that the two methods give a consistent timing calibration with an accuracy of 2 ns or better. Consequently, the beacon method alone can be used in the future to continuously determine and correct for GPS clock drifts in each individual event measured by AERA.« less

Success! Detailed Pre-event Analysis Identified the Slip Area and Magnitude of the Sept. 2012 MW 7.6 Nicoya Earthquake

NASA Astrophysics Data System (ADS)

Newman, A. V.; Protti, M.; Gonzalez, V. M.; Dixon, T. H.; Schwartz, S. Y.; Feng, L.; Peng, Z.; Marshall, J.; Malservisi, R.; Owen, S. E.

2013-05-01

On September 5th, 2012 a moment magnitude (MW) 7.6 earthquake struck the seismogenic megathrust of Nicoya Costa Rica. Though, we knew not precisely when, this event was not unexpected, and occurred after the development of substantial pre-event scientific discovery and earthquake infrastructural development. Beginning in the late- 1990's Nicoya Costa Rica was recognized by the U.S. National Science Foundation -MARGINS program as a focus area for seismogenic zone studies in part because of the unique proximity of land to the active subduction megathrust. The region also has very fast convergence (~9 cm/a) and has suffered from regular M7+ earthquakes in 1853, 1900 and 1950. Another similar event was expected by many. Pre-event analysis identified the structure of the subduction interface [Newman et al., GRL, 2002; DeShon et al., GJI, 2006], the location and rate changes of ongoing microseismicity [Newman et al., GRL, 2002, Ghosh et al.,GRL, 2008], the location and degree of locking that developed during the late interseismic [Norabuena et al., JGR, 2006; Feng et al., JGR, 2012], and its relation to ongoing low-frequency earthquakes, subduction tremor, and episodic slip events [Walter et al., GRL, 2011; Outerbridge et al., JGR, 2010, Jiang et al., G3, 2012]. Feng et al., [2012] using campaign and continuous GPS data through 2012, identified complex locked 50x50 km patch along the central coast of Nicoya, the locale that failed in Sept 2012, and concluded that the region had the potential to fail in an MW 7.8 event should the most recent locking be representative of behavior since the last major event in 1950. In operation at the time of the event was a substantial NSF-funded continuous GPS (17 station) and seismic (18 station) network maintained by USF, UCSC, and GIT, in cooperation with OVSICORI. The seismic network captured the initial motions of the mainshock before clipping, as well as pre-shock and aftershock activity [Walter et al., (this meeting), 2013]. The continuous GPS network captured the coseismic offset, and evolution of rupture and postseismic relaxation through high-rate and daily processing [Malservisi et al., Lay et al., (this meeting), 2013]. Immediately after the event, an aggressive campaign was performed to fix problems with continuously operating seismic and GPS sites, reoccupy all survey GPS sites occupied last in 2010 and reported in Feng et al., [2012], and perform a rapid coastal deformation and erosional survey [Marshall et al., (this meeting), 2013]. Here we will also detail the results of the coseismic displacement as observed by geodetic and geomorphic methods and compare the spatial distribution relative to the most recent published locking results as derived by both seismic proxy [Ghosh et al., 2008] and geodetic means [Feng et al., 2012], and discuss the implications of such detailed observations for understanding overall subduction earthquake potential.

A New Global Geodetic Strain Rate Model

NASA Astrophysics Data System (ADS)

Kreemer, C. W.; Klein, E. C.; Blewitt, G.; Shen, Z.; Wang, M.; Chamot-Rooke, N. R.; Rabaute, A.

2012-12-01

As part of the Global Earthquake Model (GEM) effort to improve global seismic hazard models, we present a new global geodetic strain rate model. This model (GSRM v. 2) is a vast improvement on the previous model from 2004 (v. 1.2). The model is still based on a finite-element type approach and has deforming cells in between the assumed rigid plates. While v.1.2 contained ~25,000 deforming cells of 0.6° by 0.5° dimension, the new models contains >136,000 cells of 0.25° by 0.2° dimension. We redefined the geometries of the deforming zones based on the definitions of Bird (2003) and Chamot-Rooke and Rabaute (2006). We made some adjustments to the grid geometry at places where seismicity and/or GPS velocities suggested the presence of deforming areas where those previous studies did not. As a result, some plates/blocks identified by Bird (2003) we assumed to deform, and the total number of plates and blocks in GSRM v.2 is 38 (including the Bering block, which Bird (2003) did not consider). GSRM v.1.2 was based on ~5,200 GPS velocities, taken from 86 studies. The new model is based on ~17,000 GPS velocities, taken from 170 studies. The GPS velocity field consists of a 1) ~4900 velocities derived by us for CPS stations publicly available RINEX data and >3.5 years of data, 2) ~1200 velocities for China from a new analysis of all CMONOC data, and 3) velocities published in the literature or made otherwise available to us. All studies were combined into the same reference frame by a 6-parameter transformation using velocities at collocated stations. Because the goal of the project is to model the interseismic strain rate field, we model co-seismic jumps while estimating velocities, ignore periods of post-seismic deformation, and exclude time-series that reflect magmatic and anthropogenic activity. GPS velocities were used to estimate angular velocities for most of the 38 rigid plates and blocks (the rest being taken from the literature), and these were used as boundary conditions for the strain rate calculations. For the strain rate calculations we used the method of Haines and Holt. In order to equally fit the data in slowly and rapidly deforming areas, we first calculated a very smooth model by setting the a priori variances of the strain rate components very low. We then used this model as a proxy for the a priori standard deviations of the final model. To add some more constraints to the model (to make it more stable), we manipulated the a priori covariance matrix to reflect the expected style of deformation derived from (an interpolation of) shallow earthquake focal mechanisms. We will show examples of the strain rate and velocity field results. We will also highlight how and where the results can be viewed and accessed through a dedicated webportal.

The North American Monsoon GPS Hydrometeorological Network 2017: A New Look at an Old Problem

NASA Astrophysics Data System (ADS)

Adams, D. K.

2017-12-01

Quantifying moisture recycling and determining water vapor source regions for deep convective precipitation have been problematic, particular in tropical continental regions. More than an academic concern, modeling convective precipitation, from cloud-resolving to global climate models, depends critically on properly representing atmospheric water vapor transport, its vertical distribution, as well as surface latent heat flux contributions. The North American Monsoon region, given its complex topography, proximity to warm oceans, striking vegetation "green up" and oftentimes subtle dynamical forcing is particular challenging in this regard. Recent studies, employing modeling and observational approaches, give a prominent role for moisture recycling in fomenting deep convective precipitation. Likewise, these studies argue for the increased importance of transport from the Gulf of Mexico/Central America and the Atlantic Ocean, relative to the Pacific Ocean/Gulf of California. In this presentation, we critically review these studies which served to motivate the NAM GPS Hydrometeorological Network 2017, detailed here. This bi-national (Mexico-US) 3-month campaign to examine water vapor source regions, and specifically, land-surface water vapor fluxes consists of 10 experimental GPS meteorological sites as well as TLALOCNet and Suominet GPS sites in the Mexican states of Sonora, Chihuahua, Sinaloa, and Baja California and in Arizona and New Mexico. Near Rayón Sonora, inside the larger regional GPSmet array, a 30km eddy covariance flux tower triangular array, with collocated GPSmet, measures continuous energy fluxes and precipitable water vapor. Preliminary results examining the local flux contribution in the triangular array to total precipitable water vapor measured are presented. Further research is then outlined.

Ionosphere Profile Estimation Using Ionosonde & GPS Data in an Inverse Refraction Calculation

NASA Astrophysics Data System (ADS)

Psiaki, M. L.

2014-12-01

A method has been developed to assimilate ionosonde virtual heights and GPS slant TEC data to estimate the parameters of a local ionosphere model, including estimates of the topside and of latitude and longitude variations. This effort seeks to better assimilate a variety of remote sensing data in order to characterize local (and eventually regional and global) ionosphere electron density profiles. The core calculations involve a forward refractive ray-tracing solution and a nonlinear optimal estimation algorithm that inverts the forward model. The ray-tracing calculations solve a nonlinear two-point boundary value problem for the curved ionosonde or GPS ray path through a parameterized electron density profile. It implements a full 3D solution that can handle the case of a tilted ionosphere. These calculations use Hamiltonian equivalents of the Appleton-Hartree magneto-plasma refraction index model. The current ionosphere parameterization is a modified Booker profile. It has been augmented to include latitude and longitude dependencies. The forward ray-tracing solution yields a given signal's group delay and beat carrier phase observables. An auxiliary set of boundary value problem solutions determine the sensitivities of the ray paths and observables with respect to the parameters of the augmented Booker profile. The nonlinear estimation algorithm compares the measured ionosonde virtual-altitude observables and GPS slant-TEC observables to the corresponding values from the forward refraction model. It uses the parameter sensitivities of the model to iteratively improve its parameter estimates in a way the reduces the residual errors between the measurements and their modeled values. This method has been applied to data from HAARP in Gakona, AK and has produced good TEC and virtual height fits. It has been extended to characterize electron density perturbations caused by HAARP heating experiments through the use of GPS slant TEC data for an LOS through the heated zone. The next planned extension of the method is to estimate the parameters of a regional ionosphere profile. The input observables will be slant TEC from an array of GPS receivers and group delay and carrier phase observables from an array of high-frequency beacons. The beacon array will function as a sort of multi-static ionosonde.

Post-Seismic Crustal Deformation Following The 1999 Izmit Earthquake, Western Part Of North Anatolian Fault Zone, Turkey

NASA Astrophysics Data System (ADS)

Gurkan, O.; Ozener, H.

2004-12-01

The North Anatolian Fault is an about 1500 km long, extending from the Karliova to the North Aegean. Turkey is a natural laboratory with high tectonic activity caused by the relative motion of the Eurasian, Arabian and Anatolian plates. Western part of Turkey and its vicinity is a seismically active area. Since 1972 crustal deformation has been observed by various kinds of geodetic measurements in the area. Three GPS networks were installed in this region by Geodesy Department of Kandilli Observatory and Earthquake Research Institute( KOERI ) of Bogazici University: (1) Iznik Network, installed on the Iznik-Mekece fault zone, seismically low active part, (2) Sapanca Network, installed on the Izmit-Sapanca fault zone, seismically active part, (3) Akyazi Network, installed on their intersection area, the Mudurnu fault zone. First period observations were performed by using terrestrial methods in 1990 and these observations were repeated annually until 1993. Since 1994, GPS measurements have been carried out at the temporary and permanent points in the area and the crustal movements are being monitored. Horizontal deformations, which have not been detected by terrestrial methods, were determined from the results of GPS measurements. A M=7.4 earthquake hit Izmit, northern Turkey, on August 17, 1999. After this earthquake many investigations have been started in the region. An international project has been performed with the collaboration of Massachussets Institute of Technology, Turkish General Command of Mapping, Istanbul Technical University, TUBITAK-Marmara Research Center and Geodesy Department of KOERI. Postseismic movements have been observed by the region-wide network. A GPS network including 49 well spread points in Marmara region was observed twice a year between 1999 and 2003 years. During these surveys, another network with 6 points has been formed by using 2 points from each 3 microgeodetic networks on NAFZ with appropriate coverage and geometry. These points have been connected by GPS observations to monitor the deformations. This expanded microgeodetic network has been occupied with Istanbul-Kandilli continuous GPS station (KANT). The objective of this paper is to present the post-seismic crustal deformation obtained from the GPS observations at the Western Part of the North Anatolian Fault (NAF) in Turkey.

Effect of tropospheric models on derived precipitable water vapor over Southeast Asia

NASA Astrophysics Data System (ADS)

Rahimi, Zhoobin; Mohd Shafri, Helmi Zulhaidi; Othman, Faridah; Norman, Masayu

2017-05-01

An interesting subject in the field of GPS technology is estimating variation of precipitable water vapor (PWV). This estimation can be used as a data source to assess and monitor rapid changes in meteorological conditions. So far, numerous GPS stations are distributed across the world and the number of GPS networks is increasing. Despite these developments, a challenging aspect of estimating PWV through GPS networks is the need of tropospheric parameters such as temperature, pressure, and relative humidity (Liu et al., 2015). To estimate the tropospheric parameters, global pressure temperature (GPT) model developed by Boehm et al. (2007) is widely used in geodetic analysis for GPS observations. To improve the accuracy, Lagler et al. (2013) introduced GPT2 model by adding annual and semi-annual variation effects to GPT model. Furthermore, Boehm et al. (2015) proposed the GPT2 wet (GPT2w) model which uses water vapor pressure to improve the calculations. The global accuracy of GPT2 and GPT2w models has been evaluated by previous researches (Fund et al., 2011; Munekane and Boehm, 2010); however, investigations to assess the accuracy of global tropospheric models in tropical regions such as Southeast Asia is not sufficient. This study tests and examines the accuracy of GPT2w as one of the most recent versions of tropospheric models (Boehm et al., 2015). We developed a new regional model called Malaysian Pressure Temperature (MPT) model, and compared this model with GPT2w model. The compared results at one international GNSS service (IGS) station located in the south of Peninsula Malaysia shows that MPT model has a better performance than GPT2w model to produce PWV during monsoon season. According to the results, MPT has improved the accuracy of estimated pressure and temperature by 30% and 10%, respectively, in comparison with GPT2w model. These results indicate that MPT model can be a good alternative tool in the absence of meteorological sensors at GPS stations in Peninsula Malaysia. Therefore, for GPS-based studies, we recommend MPT model to be used as a complementary tool for the Malaysia Real-Time Kinematic Network to develop a real-time PWV monitoring system.

Reference frame access under the effects of great earthquakes: a least squares collocation approach for non-secular post-seismic evolution

NASA Astrophysics Data System (ADS)

Gómez, D. D.; Piñón, D. A.; Smalley, R.; Bevis, M.; Cimbaro, S. R.; Lenzano, L. E.; Barón, J.

2016-03-01

The 2010, (Mw 8.8) Maule, Chile, earthquake produced large co-seismic displacements and non-secular, post-seismic deformation, within latitudes 28°S-40°S extending from the Pacific to the Atlantic oceans. Although these effects are easily resolvable by fitting geodetic extended trajectory models (ETM) to continuous GPS (CGPS) time series, the co- and post-seismic deformation cannot be determined at locations without CGPS (e.g., on passive geodetic benchmarks). To estimate the trajectories of passive geodetic benchmarks, we used CGPS time series to fit an ETM that includes the secular South American plate motion and plate boundary deformation, the co-seismic discontinuity, and the non-secular, logarithmic post-seismic transient produced by the earthquake in the Posiciones Geodésicas Argentinas 2007 (POSGAR07) reference frame (RF). We then used least squares collocation (LSC) to model both the background secular inter-seismic and the non-secular post-seismic components of the ETM at the locations without CGPS. We tested the LSC modeled trajectories using campaign and CGPS data that was not used to generate the model and found standard deviations (95 % confidence level) for position estimates for the north and east components of 3.8 and 5.5 mm, respectively, indicating that the model predicts the post-seismic deformation field very well. Finally, we added the co-seismic displacement field, estimated using an elastic finite element model. The final, trajectory model allows accessing the POSGAR07 RF using post-Maule earthquake coordinates within 5 cm for ˜ 91 % of the passive test benchmarks.

Heterogeneous Earth Structure, Deformation, and Slip During the 2010 Mw 7.2 El Mayor-Cucapah Earthquake from Geodetic Data

NASA Astrophysics Data System (ADS)

Huang, M. H.; Dickinson, H.; Fielding, E. J.; Sun, J.; Freed, A. M.; Burgmann, R.

2015-12-01

The 4th of April 2010 Mw 7.2 El Mayor-Cucapah (EMC) earthquake in Baja California and Sonora, Mexico has primarily right-lateral strike-slip motion and a minor normal slip component. The surface rupture extends about 120 km west of the boundary between the Pacific and the North American plates. The EMC event initiated near the center and ruptured bilaterally into an east-dipping strike-slip fault zone to the north and a west-dipping strike-slip zone to the south. Here we use geodetic measurements including GPS, InSAR (SAR interferometry), and sub-pixel offset measurements to characterize the fault slip during the EMC event. We use dislocation inversion methods to determine fault geometry as well as sub-fault slip distribution based on geodetic measurements. We find that assuming layered earth elastic structure increased the inferred deep slip (10-15 km depth) by up to 1.6 m (60%) compared to assuming a homogeneous elastic structure. Inferred slip was also strongly (up to 2 m) influenced by the choice of observational constraints used in the inversion. The choice of constraints also influenced the inverted seismic moment from Mw 7.20 to 7.26, and the difference is equivalent to a Mw 6.5 event. Our results show that the outcomes of coseismic inversions can vary greatly depending on the methodology, something that needs to be considered both for characterizing an earthquake and when using such results in subsequent studies of postseismic deformation.

Refining the Magnitude of the Shallow Slip Deficit

NASA Astrophysics Data System (ADS)

Xu, X.; Tong, X.; Sandwell, D. T.; Milliner, C. W. D.

2014-12-01

Geodetic inversions for slip versus depth for several major (Mw > 7) strike-slip earthquakes (e.g. 1992 Landers, 1999 Hector Mine, 2010 El_Mayor-Cucapah) show a 10% to 40% reduction in slip near surface (depth < 2 km) compared to the slip at deeper depths (5 to 8 km). This has been called the shallow slip deficit (SSD). The large magnitude of this deficit has been an enigma since it cannot be explained by shallow creep during the interseismic period or by triggered slip from nearby earthquakes. One potential explanation for the SSD is that the previous geodetic inversions used incomplete data that do not go close to fault so the shallow portions of the slip models were poorly resolved and generally underestimated. In this study we improve the geodetic inversion, especially at shallow depth by: 1) refining the InSAR processing with non-boxcar phase filtering, model-dependent range corrections, more complete phase unwrapping by SNAPHU using a correlation mask and allowing a phase discontinuity along the rupture; 2) including near-fault offset data from optical imagery and SAR azimuth offsets; 3) using more detailed fault geometry; 4) and using additional campaign GPS data. With these improved observations, the slip inversion has significantly increased resolution at shallow depth. For the Landers rupture the SSD is reduced from 45% to 16%. Similarly for the Hector Mine rupture the SSD is reduced from 15% to 5%. We are assembling all the relevant co-seismic data for the El Major-Cucapah earthquake and will report the inversion result with its SSD at the meeting.

Multidisciplinary Observations of Subduction (MOOS) Experiment in South-Central Alaska

NASA Astrophysics Data System (ADS)

Christensen, D.; Abers, G.; Freymueller, J.

2008-12-01

Seismic and geodetic data are being collected in the Kenai Peninsula and surrounding area of south central Alaska as part of the PASSCAL experiment MOOS. A total of 34 broadband seismic stations were deployed between the summers of 2007 and 2008. Seventeen of these stations continue to operate for an additional year and are scheduled to be removed in the summer of 2009. Numerous GPS campaign sites have and will be visited during the same time period. The MOOS seismic deployment provides coverage across the interplate coupled zone and adjacent transition zone in the shallow parts of the Alaskan subduction zone. It is a southern extension of an earlier broadband deployment BEAAR (Broadband Experiment Across the Alaska Range) to the north. When integrated with the previous BEAAR experiment, these data will allow high-resolution broadband imaging along a 600 km long transect over the Alaska subduction zone, at 10-15 km station spacing. The MOOS deployment allows us to test several hypotheses relating to the postulated subduction of the Yakutat Block and the nature of the coupled zone which ruptured in the great 1964 earthquake. The seismic and geodetic stations cover an area that includes part of the 1964 main asperity and the adjacent, less coupled, region to the southwest. Data gathered from this experiment will shed light on the nature of this boundary from both a geodetic and seismic (or earth structure) perspective. Shallow seismicity recorded by this network greatly improves the catalog of events in this area and helps to delineate active features in the subduction complex. Preliminary results from this project will be presented.

Glacier Ice Mass Fluctuations and Fault Instability in Tectonically Active Southern Alaska

NASA Technical Reports Server (NTRS)

SauberRosenberg, Jeanne M.; Molnia, Bruce F.

2003-01-01

Across southern Alaska the northwest directed subduction of the Pacific plate is accompanied by accretion of the Yakutat terrane to continental Alaska. This has led to high tectonic strain rates and dramatic topographic relief of more than 5000 meters within 15 km of the Gulf of Alaska coast. The glaciers of this area are extensive and include large glaciers undergoing wastage (glacier retreat and thinning) and surges. The large glacier ice mass changes perturb the tectonic rate of deformation at a variety of temporal and spatial scales. We estimated surface displacements and stresses associated with ice mass fluctuations and tectonic loading by examining GPS geodetic observations and numerical model predictions. Although the glacial fluctuations perturb the tectonic stress field, especially at shallow depths, the largest contribution to ongoing crustal deformation is horizontal tectonic strain due to plate convergence. Tectonic forces are thus the primary force responsible for major earthquakes. However, for geodetic sites located < 10-20 km from major ice mass fluctuations, the changes of the solid Earth due to ice loading and unloading are an important aspect of interpreting geodetic results. The ice changes associated with Bering Glacier s most recent surge cycle are large enough to cause discernible surface displacements. Additionally, ice mass fluctuations associated with the surge cycle can modify the short-term seismicity rates in a local region. For the thrust faulting environment of the study region a large decrease in ice load may cause an increase in seismic rate in a region close to failure whereas ice loading may inhibit thrust faulting.

The Spring 1985 high precision baseline test of the JPL GPS-based geodetic system

NASA Technical Reports Server (NTRS)

Davidson, John M.; Thornton, Catherine L.; Stephens, Scott A.; Blewitt, Geoffrey; Lichten, Stephen M.; Sovers, Ojars J.; Kroger, Peter M.; Skrumeda, Lisa L.; Border, James S.; Neilan, Ruth E.

1987-01-01

The Spring 1985 High Precision Baseline Test (HPBT) was conducted. The HPBT was designed to meet a number of objectives. Foremost among these was the demonstration of a level of accuracy of 1 to 2:10 to the 7th power, or better, for baselines ranging in length up to several hundred kilometers. These objectives were all met with a high degree of success, with respect to the demonstration of system accuracy in particular. The results from six baselines ranging in length from 70 to 729 km were examined for repeatability and, in the case of three baselines, were compared to results from colocated VLBI systems. Repeatability was found to be 5:10 to the 8th power (RMS) for the north baseline coordinate, independent of baseline length, while for the east coordinate RMS repeatability was found to be larger than this by factors of 2 to 4. The GPS-based results were found to be in agreement with those from colocated VLBI measurements, when corrected for the physical separations of the VLBI and CPG antennas, at the level of 1 to 2:10 to the 7th power in all coordinates, independent of baseline length. The results for baseline repeatability are consistent with the current GPA error budget, but the GPS-VLBI intercomparisons disagree at a somewhat larger level than expected. It is hypothesized that these differences may result from errors in the local survey measurements used to correct for the separations of the GPS and VLBI antenna reference centers.

Combined cGPS and InSAR time series for observing subsidence in the southern Central Valley due to groundwater exploitation

NASA Astrophysics Data System (ADS)

Neely, W.; Borsa, A. A.; Silverii, F.

2017-12-01

Recent droughts have increased reliance on groundwater for agricultural production in California's Central Valley. Using Interferometric Synthetic Aperture Radar (InSAR), we observe upwards of 25 cm/yr of subsidence from November 2014 to February 2017 due to intense pumping. However, these observations are contaminated by atmospheric noise and orbital errors. We present a novel method for correcting long wavelength errors in InSAR deformation estimates using time series from continuous Global Positioning System (cGPS) stations within the SAR footprint, which we apply to C-band data from the Sentinel mission. We test our method using 49 SAR acquisitions from the Sentinel 1 satellites and 107 cGPS times series from the Geodesy Advancing Geoscience and EarthScope (GAGE) network in southern Central Valley. We correct each interferogram separately, implementing an intermittent Small Baseline Subset (ISBAS) technique to produce a time series of line-of-sight surface motion from 276 InSAR pairs. To estimate the vertical component of this motion, we remove horizontal tectonic displacements predicted by the Southern California Earthquake Center's (SCEC) Community Geodetic Model. We validate our method by comparing the corrected InSAR results with independent cGPS data and find a marked improvement in agreement between the two data sets, particularly in the deformation rates. Using this technique, we characterize the time evolution of surface vertical deformation in the southern Central Valley related to human exploitation of local groundwater resources. This methodology is applicable to data from other SAR satellites, including ALOS-2 and the upcoming US-India NISAR mission.

Integrated Water Vapour Retrieval From Irish GPS Network: Results From Validation With Radiosondes And Microwave Profiler And Assimilation Into HIRLAM 7.2 Operational Forecasting Model

NASA Astrophysics Data System (ADS)

Hanafin, J. A.; Whelan, E.; McGrath, R.; Jennings, S. G.; O'Dowd, C.

2009-12-01

Retrieval of atmospheric integrated water vapour (IWV) from ground-based GPS receivers and provision of this data product for meteorological applications is the focus of the European EUMETNET GPS water vapour programme. The results presented here are the first from a project to provide such information about the state of the atmosphere around Ireland for climate monitoring and improved numerical weather prediction. Two geodetic reference GPS receivers have been deployed at Valentia Observatory in Co. Kerry and Mace Head Atmospheric Research Station in Co. Galway, Ireland. A system to retrieve column-integrated atmospheric water vapour from the data they provide has been developed. Data quality has been assessed using co-located radiosondes at Valentia and observations from a microwave profiling radiometer at Mace Head. Results from the data processing and comparisons with independent observations will be presented. Water vapour retrievals from such sensors can provide good quality observations at hourly intervals of this essential climate variable for assimilation into numerical nowcast and forecast systems. Previous studies have shown that using these data to constrain initial model conditions can improve the accuracy of precipitation forecasts, particularly for heavy rainfall. The current operational forecast model in use at Met Éireann for the region is the new version 7.2 HIRLAM (High-Resolution Limited Area Model). The effects on the forecast for Ireland have been evaluated by assimilating the data into 48-hour forecast runs of this model and results of this study will also be presented.

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, a balloon gently lifts the solar array panel to be installed on the Gravity Probe B spacecraft. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

NASA Image and Video Library

2003-11-04

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, a balloon gently lifts the solar array panel to be installed on the Gravity Probe B spacecraft. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, the Gravity Probe B spacecraft is seen with all four solar array panels installed. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

NASA Image and Video Library

2003-11-04

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, the Gravity Probe B spacecraft is seen with all four solar array panels installed. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

VANDENBERG AFB, CALIF. - A worker in the NASA spacecraft processing facility on North Vandenberg Air Force Base adjust the supports on a solar array panel to be lifted and installed on the Gravity Probe B spacecraft. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

NASA Image and Video Library

2003-11-03

VANDENBERG AFB, CALIF. - A worker in the NASA spacecraft processing facility on North Vandenberg Air Force Base adjust the supports on a solar array panel to be lifted and installed on the Gravity Probe B spacecraft. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, the Gravity Probe B spacecraft is seen with two solar array panels installed. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.

NASA Image and Video Library

2003-11-04

VANDENBERG AFB, CALIF. - In the NASA spacecraft processing facility on North Vandenberg Air Force Base, the Gravity Probe B spacecraft is seen with two solar array panels installed. Installing each array is a 3-day process and includes a functional deployment test. The Gravity Probe B mission is a relativity experiment developed by NASA’s Marshall Space Flight Center, Stanford University and Lockheed Martin. The spacecraft will test two extraordinary predictions of Albert Einstein’s general theory of relativity that he advanced in 1916: the geodetic effect (how space and time are warped by the presence of the Earth) and frame dragging (how Earth’s rotation drags space and time around with it). Gravity Probe B consists of four sophisticated gyroscopes that will provide an almost perfect space-time reference system. The mission will look in a precision manner for tiny changes in the direction of spin.