Detecting thermally driven cyclic deformation of an exfoliation sheet with lidar and radar

USGS Publications Warehouse

Collins, Brian D.; Stock, Greg M.

2014-01-01

Rock falls from steep, exfoliating cliffs are common in many landscapes. Of the many mechanisms known to trigger rock falls, thermally driven deformation is among the least quantified, despite potentially being a prevalent trigger due to its occurrence at all times of year. Here we present the results of a field-based monitoring program using instrumentation, ground-based lidar, and ground-based radar to investigate the process of thermally driven deformation of an exfoliation sheet, and the ability of remote sensing tools to capture cyclic expansion and contraction patterns. Our results indicate that thermally driven exfoliation occurs on diurnal cycles and can be measured at the submillimeter to centimeter scale using high-resolution strain gauges, short-range (2 km) radar interfer-ometry.

WE-G-BRD-06: Volumetric Cine MRI (VC-MRI) Estimated Based On Prior Knowledge for On-Board Target Localization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, W; Yin, F; Cai, J

Purpose: To develop a technique to generate on-board VC-MRI using patient prior 4D-MRI, motion modeling and on-board 2D-cine MRI for real-time 3D target verification of liver and lung radiotherapy. Methods: The end-expiration phase images of a 4D-MRI acquired during patient simulation are used as patient prior images. Principal component analysis (PCA) is used to extract 3 major respiratory deformation patterns from the Deformation Field Maps (DFMs) generated between end-expiration phase and all other phases. On-board 2D-cine MRI images are acquired in the axial view. The on-board VC-MRI at any instant is considered as a deformation of the prior MRI atmore » the end-expiration phase. The DFM is represented as a linear combination of the 3 major deformation patterns. The coefficients of the deformation patterns are solved by matching the corresponding 2D slice of the estimated VC-MRI with the acquired single 2D-cine MRI. The method was evaluated using both XCAT (a computerized patient model) simulation of lung cancer patients and MRI data from a real liver cancer patient. The 3D-MRI at every phase except end-expiration phase was used to simulate the ground-truth on-board VC-MRI at different instances, and the center-tumor slice was selected to simulate the on-board 2D-cine images. Results: Image subtraction of ground truth with estimated on-board VC-MRI shows fewer differences than image subtraction of ground truth with prior image. Excellent agreement between profiles was achieved. The normalized cross correlation coefficients between the estimated and ground-truth in the axial, coronal and sagittal views for each time step were >= 0.982, 0.905, 0.961 for XCAT data and >= 0.998, 0.911, 0.9541 for patient data. For XCAT data, the maximum-Volume-Percent-Difference between ground-truth and estimated tumor volumes was 1.6% and the maximum-Center-of-Mass-Shift was 0.9 mm. Conclusion: Preliminary studies demonstrated the feasibility to estimate real-time VC-MRI for on-board target localization before or during radiotherapy treatments. National Institutes of Health Grant No. R01-CA184173; Varian Medical System.« less

Spatiotemporal Patterns of Precipitation-Modulated Landslide Deformation From Independent Component Analysis of InSAR Time Series

NASA Astrophysics Data System (ADS)

Cohen-Waeber, J.; Bürgmann, R.; Chaussard, E.; Giannico, C.; Ferretti, A.

2018-02-01

Long-term landslide deformation is disruptive and costly in urbanized environments. We rely on TerraSAR-X satellite images (2009-2014) and an improved data processing algorithm (SqueeSAR™) to produce an exceptionally dense Interferometric Synthetic Aperture Radar ground deformation time series for the San Francisco East Bay Hills. Independent and principal component analyses of the time series reveal four distinct spatial and temporal surface deformation patterns in the area around Blakemont landslide, which we relate to different geomechanical processes. Two components of time-dependent landslide deformation isolate continuous motion and motion driven by precipitation-modulated pore pressure changes controlled by annual seasonal cycles and multiyear drought conditions. Two components capturing more widespread seasonal deformation separate precipitation-modulated soil swelling from annual cycles that may be related to groundwater level changes and thermal expansion of buildings. High-resolution characterization of landslide response to precipitation is a first step toward improved hazard forecasting.

2014-2016 Mt. Etna Ground deformation imaged by SISTEM approach using GPS and SENTINEL-1A/1B TOPSAR data

NASA Astrophysics Data System (ADS)

Bonforte, Alessandro; Guglielmino, Francesco; Puglisi, Giuseppe

2017-04-01

In the frame of the EC FP7 MED-SUV project (call FP7 ENV.2012.6.4-2), and thanks to the GEO-GSNL initiative, GPS data and SENTINEL 1A/1B TOPSAR acquired on Mt. Etna between October 2014 and November 2016 were analyzed. The SENTINEL data were used in order to combine and integrate them with GPS, and detail the ground deformation recorded by GPS on Mt. Etna, during the last two-year's volcanic activity. The Sentinel data were processed by GAMMA software, using a spectral diversity method and a procedure able to co-register the SENTINEL pairs with extremely high precision (< 0.01 pixel). In order to optimize the time processing, a new software architecture based on the hypervisor virtualization technology for the x64 versions of Windows has been implemented. The DInSAR results are analysed and successively used as input for the time series analysis using the StaMPS package. On December 28, 2014 eruptive activity resumed at Mt. Etna with a fire fountain activity feeding two lava flows spreading on the eastern and south-western upper flanks of the volcano, producing evident deformation at the summit of the volcano. GPS displacements and Sentinel-1A ascending interferogram were calculated in order to image the ground deformation pattern accompanying the eruption. The ground deformation pattern has been perfectly depicted by the GPS network, mainly affecting the uppermost part of the volcano edifice, with a strong decay of the deformation, according to a very shallow and strong dyke intrusion. The Sentinel 1A SAR data, covering the similar time spanning, confirmed that most of displacements are related to the dike intrusion, and evidenced a local gravity-driven motion of the western wall of the Valle del Bove, probably related to the dike intrusion. To monitor the temporal successive evolution of ground deformation, we performed an A-DInSAR SENTINEL analysis using the Small BAseline Subset (SBAS) approach included with the StaMPS processing package. The April 2015-December 2015, SBAS Time series, shown a volcano inflation, with an uplift of about 28 mm localized in the central and western area of the volcano. Suddenly, in the first days of December 2015, volcanic activity abruptly restarted at the central crater with a very strongly explosive eruption; this kind of activity continued, with a decreasing intensity, with other episodes at the same crater and then involving, in turn, all the other three summit craters of the volcano. On December 8, when the eruptive activity was concluding, a seismic swarm affected the uppermost part of the Pernicana fault where it joins the NE-Rift. The SBAS time series have then been integrated by the SISTEM algorithm with the ground displacements measured by two GPS surveys carried out on the NE flank of the volcano at the end of April and in mid-December 2015. Results of this data integration provide a very detailed picture of the ground deformation pattern on the volcano, preceding and accompanying the vigorous eruption and the seismic swarm; besides the general inflation of the edifice during the pre-eruptive period. The January 2016 - November 2016 is the last period analyzed, characterized by the kinematic of the eastern unstable flank, with displacement involving both the Pernicana fault and the other structures dissecting this sector of the volcano.

Modelling of The Dyke Emplacement Leading To The Etna July 2001 Eruption Through Continuous Tilt and GPS Data

NASA Astrophysics Data System (ADS)

Bonaccorso, A.; Aloisi, M.; Mattia, A.

During the June 2001 eruption of Mt. Etna the continuous ground deformation mon- itoring have been recorded through tilt (9 stations) and GPS (11 stations) permanent networks. The evolution of the July crisis preceding and leading to the eruption has been monitored through the tilt and GPS continuous measurements, which constrained in time the final intrusion and inferred the position and geometry of the uprising dyke. The tilt signals, which record 48 samples/day, fixed the time action of the intrusion, whose main effects are recorded during 13-15 July in concomitance with the first days of the seismic crisis. In particular, the high precision long-base mercury tiltmeter, in- stalled at Pizzi Deneri observatory in the high north-eastern flank close to the crater area, showed very well the continuous deformation during the dyke emplacement. The deformation pattern, at the entire volcano scale, was well characterised by the daily measurement sessions recorded at the GPS permanent network. The variations recorded at the permanent GPS stations started from July 13 and, in agreement with tilt recordings, were mainly cumulated in the following two days. The GPS measurements showed horizontal displacement vectors much bigger than vertical changes. The defor- mation pattern indicates the response to a tensile mechanisms that appears compatible with an intrusion in the volcano edifice along a ca. N-S direction. In this poster we show the modelling of the marked ground deformation changes recorded in the days before the eruption starting. The first results show that a tensile crack with an opening dislocation of ~3 m. and crossing the entire edifice, south-west to the crater area, can explain the recorded deformation pattern. The location of the modelled tensile source fits the seismogenetic zone characterized by epicenters aligned in a ca. N-S direction with the foci clustered in the last shallow kilometers. The ground deformation pat- tern associated with the final uprising and its modelling suggest a dyke emplacement which appears different, both in terms of velocity and source position, with respect to the sources modelled for the other lateral eruptions in the previous twenty years.

The role of thermo-rheological properties of the crust beneath Ischia Island (Southern Italy) in the modulation of the ground deformation pattern

NASA Astrophysics Data System (ADS)

Castaldo, R.; Gola, G.; Santilano, A.; De Novellis, V.; Pepe, S.; Manzo, M.; Manzella, A.; Tizzani, P.

2017-09-01

In this paper we develop a model of the ground deformation behaviour occurred at Ischia Island (Southern Italy) in the 1992-2010 time period. The model is employed to investigate the forces and physical parameters of the crust controlling the subsidence of the Island. To this aim, we integrate and homogenize in a Finite Element (FE) environment a large amount of data derived from several and different observation techniques (i.e., geological, geophysical and remote sensing). In detail, the main steps of the multiphysics model are: (i) the generation of a 3D geological model of the crust beneath the Island by merging the available geological and geophysical information; (ii) the optimization of a 3D thermal model by exploiting the thermal measurements available in literature; (iii) the definition of the 3D Brittle/Ductile transition by using the temperature distribution of the crust and the physical information of the rocks; (iv) the optimization of the ground deformation velocity model (that takes into account the rheological stratification) by considering the spatial and temporal information detected via satellite multi-orbit C-Band SAR (Synthetic Aperture Radar) measurements acquired during the 1992-2010 time period. The achieved results allow investigating the physical process responsible for the observed ground deformation pattern. In particular, they reveal how the rheology modulates the spatial and temporal evolution of the long-term subsidence phenomenon, highlighting a coupling effect of the viscosities of the rocks and the gravitational loading of the volcano edifice. Moreover, the achieved results provide a very detailed and realistic velocity field image of the subsurface crust of the Ischia Island Volcano.

New insights into the 2012 Emilia (Italy) seismic sequence through advanced numerical modeling of ground deformation InSAR measurements

NASA Astrophysics Data System (ADS)

Tizzani, P.; Castaldo, R.; Solaro, G.; Pepe, S.; Bonano, M.; Casu, F.; Manunta, M.; Manzo, M.; Pepe, A.; Samsonov, S.; Lanari, R.; Sansosti, E.

2013-05-01

We provide new insights into the two main seismic events that occurred in 2012 in the Emilia region, Italy. We extend the results from previous studies based on analytical inversion modeling of GPS and RADARSAT-1 InSAR measurements by exploiting RADARSAT-2 data. Moreover, we benefit from the available large amount of geological and geophysical information through finite element method (FEM) modeling implemented in a structural-mechanical context to investigate the impact of known buried structures on the modulation of the ground deformation field. We find that the displacement pattern associated with the 20 May event is consistent with the activation of a single fault segment of the inner Ferrara thrust, in good agreement with the analytical solution. In contrast, the interpretation of the 29 May episode requires the activation of three different fault segments and a block roto-translation of the Mirandola anticline. The proposed FEM-based methodology is applicable to other seismic areas where the complexity of buried structures is known and plays a fundamental role in the modulation of the associated surface deformation pattern.

Solving Laplace equation to investigate the volcanic ground deformation pattern

NASA Astrophysics Data System (ADS)

Brahmi, Mouna; Castaldo, Raffaele; Barone, Andrea; Fedi, Maurizio; Tizzani, Pietro

2017-04-01

Volcanic eruptions are generally preceded by unrest phenomena, which are characterized by variations in the geophysical and geochemical state of the system. The most evident unrest parameters are the spatial and temporal topographic changes, which typically result in uplift or subsidence of the volcano edifice, usually caused by magma accumulation or hot fluid concentration in shallow reservoirs (Denasoquo et al., 2009). If the observed ground deformation phenomenon is very quick and the time evolution of the process shows a linear tendency, we can approximate the problem by using an elastic rheology model of the crust beneath the volcano. In this scenario, by considering the elastic field theory under the Boussinesq (1885) and Love (1892) approximations, we can evaluate the displacement field induced by a generic source in a homogeneous, elastic, half-space at an arbitrary point. To this purpose, we use the depth to extreme points (DEXP) method. By using this approach, we are able to estimate the depth and the geometry of the active source, responsible of the observed ground deformation.

Numerical models of caldera deformation: Effects of multiphase and multicomponent hydrothermal fluid flow

USGS Publications Warehouse

Hutnak, M.; Hurwitz, S.; Ingebritsen, S.E.; Hsieh, P.A.

2009-01-01

Ground surface displacement (GSD) in large calderas is often interpreted as resulting from magma intrusion at depth. Recent advances in geodetic measurements of GSD, notably interferometric synthetic aperture radar, reveal complex and multifaceted deformation patterns that often require complex source models to explain the observed GSD. Although hydrothermal fluids have been discussed as a possible deformation agent, very few quantitative studies addressing the effects of multiphase flow on crustal mechanics have been attempted. Recent increases in the power and availability of computing resources allow robust quantitative assessment of the complex time-variant thermal interplay between aqueous fluid flow and crustal deformation. We carry out numerical simulations of multiphase (liquid-gas), multicomponent (H 2O-CO2) hydrothermal fluid flow and poroelastic deformation using a range of realistic physical parameters and processes. Hydrothermal fluid injection, circulation, and gas formation can generate complex, temporally and spatially varying patterns of GSD, with deformation rates, magnitudes, and geometries (including subsidence) similar to those observed in several large calderas. The potential for both rapid and gradual deformation resulting from magma-derived fluids suggests that hydrothermal fluid circulation may help explain deformation episodes at calderas that have not culminated in magmatic eruption.

Geomorphic response to tectonically-induced ground deformation in the Wabash Valley

USGS Publications Warehouse

Fraser, G.S.; Thompson, T.A.; Olyphant, G.A.; Furer, L.; Bennett, S.W.

1997-01-01

Numerous low- to moderate-intensity earthquakes have been recorded in a zone of diffuse modern seismicity in southwest Indiana, southeast Illinois, and northernmost Kentucky. Structural elements within the zone include the Wabash Valley Fault System, the LaSalle Anticlinal Belt in western Illinois, and the Rough Creek-Shawneetown Fault System in northern Kentucky. The presence of seismically-induced liquefaction features in the near-surface alluvial sediments in the region indicates that strong ground motion has occurred in the recent geological past, but because the glacial and alluvial sediments in the Wabash Valley appear to be otherwise undisturbed, post-Paleozoic ground deformation resulting from movement on these structural elements has not yet been documented. Morphometric analysis of the land surface, detailed mapping of geomorphic elements in the valley, reconnaissance drilling of the Holocene and Pleistocene alluvium, and structural analysis of the bedrock underlying the valley were used to determine whether the geomorphology of the valley and the patterns of alluviation of the Wabash River were affected by surface deformation associated with the seismic zone during the late Pleistocene and Holocene. Among the observed features in the valley that can be attributed to deformation are: (1) tilting of the modern land surface to the west, (2) preferred channel migration toward the west side of the valley, with concomitant impact on patterns of soil development and sedimentation rate, (3) a convex longitudinal profile of the Wabash River where it crosses the LaSalle Anticlinal Belt, and (4) increased incision of the river into its floodplain downstream from the anticlinal belt.

Impact of Sauropod Dinosaurs on Lagoonal Substrates in the Broome Sandstone (Lower Cretaceous), Western Australia

PubMed Central

Thulborn, Tony

2012-01-01

Existing knowledge of the tracks left by sauropod dinosaurs (loosely ‘brontosaurs’) is essentially two-dimensional, derived mainly from footprints exposed on bedding planes, but examples in the Broome Sandstone (Early Cretaceous) of Western Australia provide a complementary three-dimensional picture showing the extent to which walking sauropods could deform the ground beneath their feet. The patterns of deformation created by sauropods traversing thinly-stratified lagoonal deposits of the Broome Sandstone are unprecedented in their extent and structural complexity. The stacks of transmitted reliefs (underprints or ghost prints) beneath individual footfalls are nested into a hierarchy of deeper and more inclusive basins and troughs which eventually attain the size of minor tectonic features. Ultimately the sauropod track-makers deformed the substrate to such an extent that they remodelled the topography of the landscape they inhabited. Such patterns of substrate deformation are revealed by investigating fragmentary and eroded footprints, not by the conventional search for pristine footprints on intact bedding planes. For that reason it is not known whether similar patterns of substrate deformation might occur at sauropod track-sites elsewhere in the world. PMID:22662116

Detection of ground deformation over Sharm El-Sheikh-Ras Nasrani coastal zone, South Sinai (Egypt), by using time series SAR interferometry

NASA Astrophysics Data System (ADS)

Seleem, Tarek A.; Parcharidis, Issaak; Foumelis, Michael; Kourkouli, Penelope

2011-03-01

The investigation area is located in the most southern part of Sinai Peninsula boarded from the west by the Gulf of Suez and from the east by the Gulf of Aqaba. The present study concerns the application of stacking and persistent scattering of SAR interferometry in order to monitor ground deformation in the southern part of Sharm El-Shiekh area. The specific techniques were applied in order to reduce the influence of atmospheric effects on the ground deformation estimates. For this purpose a total number of 26 ENVISAT ASAR scenes covering the period between 2003 and 2009 were processed and analyzed. Interferometric processing results show both patterns of uplift and downlift in the study area. Specifically an area along the coastline with a N-S direction, corresponding to the build up zone of Sharm El-Sheikh, shows annual average subsidence rates between 5 and 7 mm/yr along the line of sight (LOS). On the contrary, Sharm El-Maya, an inner zone, parallel to the above subsided area; shows maximum slant range uplift of 5 mm/yr. The obtained results of both stacking and persistent scattering indicate that the ground deformation in Sharm El-Sheikh-Ras Nasrani coastal zone is attributed to several effecting factors compromising water pumping, lithology, seismicity, and possible active fracture. The contribution of all these factors is discussed in the context.

Surface deformation induced by water pumping for construction of Mass Rapid Transportation in Taipei basin

NASA Astrophysics Data System (ADS)

Hu, J. C.; Wu, P. C.; Tung, H.; Tsai, M. C.

2017-12-01

In 1968, there were 2,200 wells in the Taipei Basin used for water supply to meet the requirement of high population density. The overuse of ground water lead to the land subsidence rate up to 5 cm/yr. Although the government had already begun to limit groundwater pumping since 1968, the groundwater in the Taipei Basin demonstrated temporary fluctuation induced by pumping water for large deep excavation site or engineering usage. The previous study based on precise leveling suggested that the surface deformation was highly associated with the recovery of water level. In 1989, widespread uplift dominated in Taipei basin due to the recovery of ground water Table. In this study, we use 37 high-resolution X-band COSMO-SkyMed radar images from May 2011 to April 2015 to characterize deformation pattern in the period of construction of Mass Rapid Transportation (MRT). We also use 30 wells and 380 benchmarks of precise leveling in Taipei basin to study the correlation of surface deformation and change of ground water table. The storability is roughly constant across most of the aquifer with values between 0.8 x 10-4 and 1.3 x 10-3. Moreover, the high water pumping in two major aquifers, Jignme and Wuku Foramtions, before the underground construction for MRT led to inflict surface deformation and no time delay observed for surface deformation during the water pumping. It implies that the poro-elastic effect dominates in major aquifers in Taipei basin.

Multi-Temporal Interferometry to Investigate Landslide Dynamics in a Tropical Urban Environment: Focus on Bukavu (DR Congo)

NASA Astrophysics Data System (ADS)

Monsieurs, E.; Dille, A.; Nobile, A.; d'Oreye, N.; Kervyn, F.; Dewitte, O.

2017-12-01

Landslides can lead to high impacts in less developed countries, particularly in some urban tropical environments where a combination of intense rainfall, active tectonics, steep topography and high population density can be found. However, the processes controlling landslides initiation and their evolution through time remains poorly understood. Here we show the relevance of the use of multi-temporal differential SAR interferometry (DInSAR) to characterize ground deformations associated to landslides in the rapidly expanding city of Bukavu (DR Congo). A series of 70 COSMO-SkyMed SAR images acquired between March 2015 and April 2016 with a mean revisiting time of 8 days were used to produce displacement rate maps and ground deformation time series using the Small Baseline Subset approach. Results show that various landslide processes of different ages, mechanisms and state of activity can be identified across Bukavu city. InSAR ground deformation maps reveal for instance the complexity of a large (1.5 km²) active slide affecting a densely inhabited slum neighbourhood and characterized by the presence of sectors moving at different rates (ranging from 10 mm/yr up to 75 mm/yr in LOS direction). The evaluation of the ground deformations captured by DInSAR through a two-step validation procedure combining Differential GPS measurements and field observations attested the reliability of the measurements as well as the capability of the technique to grasp the deformation pattern affecting this complex tropical-urban environment. However, longer time series will be needed to infer landside response to climate, seismic and anthropogenic activities.

Assessing the reliability and consistency of InSAR and GNSS data for retrieving 3D-displacement rapid changes, the example of the 2015 Piton de la Fournaise eruptions

NASA Astrophysics Data System (ADS)

Peltier, Aline; Froger, Jean-Luc; Villeneuve, Nicolas; Catry, Thibault

2017-09-01

InSAR and GNSS are now the best and most developed techniques in the Earth sciences to track deformation, especially in volcanology. In this study, we assess the reliability and consistency of these two techniques for measuring 3-D ground displacements - and not only the displacement in the direction of the InSAR Line of Sight - on volcanoes during rapid changes. The use of a large amount of satellite data (X, C, L-band as well as right and left-looking acquisitions) made it possible to retrieve the 3-D displacement components with an unprecedented accuracy. We carry out this evaluation on the Piton de la Fournaise volcano, where four eruptions occurred in 2015. The comparison between GNSS and InSAR allows us: (i) to describe the deformation pattern associated with these eruptions, (ii) to quantify the discrepancies between InSAR and GNSS, and (iii) to discuss the limits and the complementarities of InSAR and GNSS. The ground deformation patterns associated with the four eruptions of Piton de la Fournaise in 2015 are typical of this volcano, with decimeter ground displacements asymmetrically distributed along the dike path, evidencing a preferential eastward motion, particularly visible thanks to the broad spatial coverage of InSAR. Except for the NS component, InSAR and GNSS data are in overall agreement, with most of the GNSS-InSAR residuals < 2.5 cm and < 5 cm on the EW and vertical component, respectively, i.e. within the error bar of the two methods. Most of the discrepancies on the terminal cone can be attributed to uncorrected atmospheric effects in InSAR. Our study confirms the consistency and the complementarity of the two methods to characterize (i) the 3-D ground deformation distribution in high spatial resolution (InSAR), and (ii) the dynamism (GNSS) associated with eruptive activity.

Horizontal ground deformation patterns and magma storage during the Puu Oo eruption of Kilauea volcano, Hawaii: episodes 22-42

USGS Publications Warehouse

Hoffmann, J.P.; Ulrich, G.E.; Garcia, M.O.

1990-01-01

Horizontal ground deformation measurements were made repeatedly with an electronic distance meter near the Puu Oo eruption site approximately perpendicular to Kilauea's east rift zone (ERZ) before and after eruptive episodes 22-42. Line lengths gradually extended during repose periods and rapidly contracted about the same amount following eruptions. The repeated extension and contraction of the measured lines are best explained by the elastic response of the country rock to the addition and subsequent eruption of magma from a local reservoir. The deformation patterns are modeled to constrain the geometry and location of the local reservoir near Puu Oo. The observed deformation is consistent with deformation patterns that would be produced by the expansion of a shallow, steeply dipping dike just uprift of Puu Oo striking parallel to the trend of the ERZ. The modeled dike is centered about 800 m uprift of Puu Oo. Its top is at a depth of 0.4 km, its bottom at about 2.9 km, and the length is about 1.6 km; the dike strikes N65?? E and dips at about 87??SE. The model indicates that the dike expanded by 11 cm during repose periods, for an average volumetric expansion of nearly 500 000 m3. The volume of magma added to the dike during repose periods was variable but correlates positively with the volume of erupted lava of the subsequent eruption and represents about 8% of the new lava extruded. Dike geometry and expansion values are used to estimate the pressure increase near the eruption site due to the accumulation of magma during repose periods. On average, vent pressures increased by about 0.38 MPa during the repose periods, one-third of the pressure increase at the summit. The model indicates that the dikelike body below Puu Oo grew in volume from 3 million cubic meters (Mm3) to about 10-12 Mm3 during the series of eruptions. The width of this body was probably about 2.5-3.0 m. No net long-term deformation was detected along the measured deformation lines. ?? 1990 Springer-Verlag.

Numerical Modeling of Surface Deformation due to Magma Chamber Inflation/Deflation in a Heterogeneous Viscoelastic Half-space

NASA Astrophysics Data System (ADS)

Dichter, M.; Roy, M.

2015-12-01

Interpreting surface deformation patterns in terms of deeper processes in regions of active magmatism is challenging and inherently non-unique. This study focuses on interpreting the unusual sombrero-shaped pattern of surface deformation in the Altiplano Puna region of South America, which has previously been modeled as the effect of an upwelling diapir of material in the lower crust. Our goal is to investigate other possible interpretations of the surface deformation feature using a suite of viscoelastic models with varying material heterogeneity. We use the finite-element code PyLith to study surface deformation due to a buried time-varying (periodic) overpressure source, a magma body, at depth within a viscoelastic half-space. In our models, the magma-body is a penny-shaped crack, with a cylindrical region above the crack that is weak relative to the surrounding material. We initially consider a magma body within a homogeneous viscoelastic half-space to determine the effect of the free surface upon deformation above and beneath the source region. We observe a complex depth-dependent phase relationship between stress and strain for elements that fall between the ground surface and the roof of the magma body. Next, we consider a volume of weak material (faster relaxation time relative to background) that is distributed with varying geometry around the magma body. We investigate how surface deformation is governed by the spatial distribution of the weak material and its rheologic parameters. We are able to reproduce a "sombrero" pattern of surface velocities for a range of models with material heterogeneity. The wavelength of the sombrero pattern is primarily controlled by the extent of the heterogeneous region, modulated by flexural effects. Our results also suggest an "optimum overpressure forcing frequency" where the lifetime of the sombrero pattern (a transient phenomenon due to the periodic nature of the overpressure forcing) reaches a maximum. Through further research we hope to better understand how the parameter space of our forward model controls the distribution of surface deformation and eventually develop a better understanding of the observed pattern of surface deformation in the Altiplano Puna.

Development of a Subject-Specific Foot-Ground Contact Model for Walking.

PubMed

Jackson, Jennifer N; Hass, Chris J; Fregly, Benjamin J

2016-09-01

Computational walking simulations could facilitate the development of improved treatments for clinical conditions affecting walking ability. Since an effective treatment is likely to change a patient's foot-ground contact pattern and timing, such simulations should ideally utilize deformable foot-ground contact models tailored to the patient's foot anatomy and footwear. However, no study has reported a deformable modeling approach that can reproduce all six ground reaction quantities (expressed as three reaction force components, two center of pressure (CoP) coordinates, and a free reaction moment) for an individual subject during walking. This study proposes such an approach for use in predictive optimizations of walking. To minimize complexity, we modeled each foot as two rigid segments-a hindfoot (HF) segment and a forefoot (FF) segment-connected by a pin joint representing the toes flexion-extension axis. Ground reaction forces (GRFs) and moments acting on each segment were generated by a grid of linear springs with nonlinear damping and Coulomb friction spread across the bottom of each segment. The stiffness and damping of each spring and common friction parameter values for all springs were calibrated for both feet simultaneously via a novel three-stage optimization process that used motion capture and ground reaction data collected from a single walking trial. The sequential three-stage process involved matching (1) the vertical force component, (2) all three force components, and finally (3) all six ground reaction quantities. The calibrated model was tested using four additional walking trials excluded from calibration. With only small changes in input kinematics, the calibrated model reproduced all six ground reaction quantities closely (root mean square (RMS) errors less than 13 N for all three forces, 25 mm for anterior-posterior (AP) CoP, 8 mm for medial-lateral (ML) CoP, and 2 N·m for the free moment) for both feet in all walking trials. The largest errors in AP CoP occurred at the beginning and end of stance phase when the vertical ground reaction force (vGRF) was small. Subject-specific deformable foot-ground contact models created using this approach should enable changes in foot-ground contact pattern to be predicted accurately by gait optimization studies, which may lead to improvements in personalized rehabilitation medicine.

Development of a Subject-Specific Foot-Ground Contact Model for Walking

PubMed Central

Jackson, Jennifer N.; Hass, Chris J.; Fregly, Benjamin J.

2016-01-01

Computational walking simulations could facilitate the development of improved treatments for clinical conditions affecting walking ability. Since an effective treatment is likely to change a patient's foot-ground contact pattern and timing, such simulations should ideally utilize deformable foot-ground contact models tailored to the patient's foot anatomy and footwear. However, no study has reported a deformable modeling approach that can reproduce all six ground reaction quantities (expressed as three reaction force components, two center of pressure (CoP) coordinates, and a free reaction moment) for an individual subject during walking. This study proposes such an approach for use in predictive optimizations of walking. To minimize complexity, we modeled each foot as two rigid segments—a hindfoot (HF) segment and a forefoot (FF) segment—connected by a pin joint representing the toes flexion–extension axis. Ground reaction forces (GRFs) and moments acting on each segment were generated by a grid of linear springs with nonlinear damping and Coulomb friction spread across the bottom of each segment. The stiffness and damping of each spring and common friction parameter values for all springs were calibrated for both feet simultaneously via a novel three-stage optimization process that used motion capture and ground reaction data collected from a single walking trial. The sequential three-stage process involved matching (1) the vertical force component, (2) all three force components, and finally (3) all six ground reaction quantities. The calibrated model was tested using four additional walking trials excluded from calibration. With only small changes in input kinematics, the calibrated model reproduced all six ground reaction quantities closely (root mean square (RMS) errors less than 13 N for all three forces, 25 mm for anterior–posterior (AP) CoP, 8 mm for medial–lateral (ML) CoP, and 2 N·m for the free moment) for both feet in all walking trials. The largest errors in AP CoP occurred at the beginning and end of stance phase when the vertical ground reaction force (vGRF) was small. Subject-specific deformable foot-ground contact models created using this approach should enable changes in foot-ground contact pattern to be predicted accurately by gait optimization studies, which may lead to improvements in personalized rehabilitation medicine. PMID:27379886

Global synthesis of volcano deformation: Results of the Volcano Deformation Task Force

NASA Astrophysics Data System (ADS)

Pritchard, M. E.; Jay, J.; Biggs, J.; Ebmeier, S. K.; Delgado, F.

2013-12-01

Ground deformation in volcanic regions is being observed more frequently -- the number of known deforming volcanoes has increased from 44 in 1997 to more than 210 in 2013 thanks in large part thanks to the availability of satellite InSAR observations. With the launch of new SAR satellites in the coming years devoted to global deformation monitoring, the number of well-studied episodes of volcano deformation will continue to increase. But evaluating the significance of the observed deformation is not always straightforward -- how often do deformation episodes lead to eruption? Are there certain characteristics of the deformation or the volcano that make the linkage between deformation and eruption more robust -- for example the duration or magnitude of the ground deformation and/or the composition and tectonic setting of the volcano? To answer these questions, a global database of volcano deformation events is needed. Recognizing the need for global information on volcano deformation and the opportunity to address it with InSAR and other techniques, we formed the Volcano Deformation Database Task force as part of Global Volcano Model. The three objectives of our organization are: 1) to compile deformation observations of all volcanoes globally into appropriate formats for WOVOdat and the Global Volcanism Program of the Smithsonian Institution. 2) document any relation between deformation events and eruptions for the Global assessment of volcanic hazard and risk report for 2015 (GAR15) for the UN. 3) to better link InSAR and other remote sensing observations to volcano observatories. We present the first results from our global study of the relation between deformation and eruptions, including case studies of particular eruptions. We compile a systematically-observed catalog of >500 volcanoes with observation windows up to 20 years. Of 90 volcanoes showing deformation, 40 erupted. The positive predictive value (PPV = 0.44) linking deformation and eruption on this timescale indicates ';strong' evidential worth. The negative predictive value (NPV = 0.94) linking non-deformation with non-eruption, is even stronger. But, linking individual deformation events to eruptions is unreliable with existing InSAR data that are rarely available in the critical days to weeks before the eruption of a volcano that has been dormant for decades to millenia. For example, while ground deformation was observed before the 2011 eruptions of Cordon Caulle and Cerro Hudson (both in Chile), the observations were too infrequent to see any change in the pattern or rate of deformation before the eruptions. Before 2011, Cordon Caulle and Cerro Hudson both erupted in the 20th century, but the 2008 eruption of Chaiten (also in Chile) was preceded by centuries of dormancy and still had no measured precursory deformation up to two weeks before eruption. New InSAR missions with more frequent observations along with ground observations from tiltmeters and GPS are essential to constrain whether there is a reliable deformation signal before eruption.

Correlation between elevation change and groundwater level following the termination of salt exploitation in the city of Tuzla (BiH)

NASA Astrophysics Data System (ADS)

Mancini, F.; Stecchi, F.; Gabbianelli, G.

2012-04-01

Ground subsidence triggered by salt mining from deposits located beneath the city of Tuzla (Bosnia & Herzegovina) is one of the major dangerous factor acting on a very densely urbanized area since 1950, when the salt deposits exploitation by means of boreholes began. As demonstrated in previous work, subsidence induced several hazard factors such as a severe ground deformation, the arising of deep and superficial fractures and very fast water table fluctuations depending on the net amount of brine extraction. The historical ground deformation rates have been investigated by means of traditional geodetic surveys carried out within two periods. The first leg spans from 1956 to 1991, when measurements were ceased due to the Balkans' conflict, and the second from 1996 to 2003. More recently, the monitoring of ground deformation processes is being performed by the use of novel geomatic methodologies and subsequent analysis of geospatial data. The analysis of the historical dataset revealed a cumulative subsidence as high as 12 meters during the whole period, causing damage to buildings and infrastructures within an area that includes a large portion of the historical town, nowadays almost entirely destroyed. In this study we present a detailed analysis and correlation between the water table fluctuation under the city of Tuzla and recent surface deformation processes detected by close and accurate elevation surveys. The analysis highlighted a very complex spatial and temporal pattern of surface deformation. From 2006 and 2010 various stages in the deformation processes were observed in the spatial and temporal domains. The main subsidence trend show significant rates at the beginning of the time period, with gradual stabilization that, somewhere, turns to a significant ground uplift rate. This behavior seems to be strongly correlated to the water table movement that, after a reduction in the brine exploitation experienced in the first part of the mentioned period, shows a sudden rise of piezometric levels. The new hydrostatic equilibrium is now counterbalancing the sinking phenomena and the vertical displacements are nowadays ranging from -100mm/yr to +20mm/yr. Final conclusions focus on the strict relationship between the two investigated phenomena, pointing out the importance of control the water table movements to identify and prevent further ground deformations.

Ground Subsidence Monitoring with MT-InSAR and Mechanism Inversion Over Xi'an, China

NASA Astrophysics Data System (ADS)

Peng, M. M.; Zhao, C. Y.; Zhang, Q.; Zhang, J.; Liu, Y. Y.

2018-04-01

The ancient Xi'an, China, has been suffering severe land subsidence and ground fissure hazards since the 1960s, which has affected the safety of Subways. Multi-sensor SAR data are conducted to monitor the latest complex ground deformation and its influence on subway line No.3 over Xi'an. Annual deformation rates have been retrieved to reveal the spatiotemporal evolution of ground subsidence in Xi'an city from 2013 to 2017. Meanwhile, the correlation between land subsidence and ground fissures are analyzed by retrieving the deformation differences in both sides of the fissures. Besides, the deformation along subway line No. 3 is analyzed, and the fast deformation section is quantitatively studied. Finally, a flat lying sill model with distributed contractions is implemented to model the InSAR deformation over YHZ subsidence center, which manifests that the ground deformation is mainly caused by groundwater withdrawal.

InSAR Time Series to Characterize Landslide Ground Deformations in a Tropical Urban Environment: Focus on Bukavu, East African Rift System (RD Congo).

NASA Astrophysics Data System (ADS)

Nobile, A.; d'Oreye, N.; Monsieurs, E.; Dewitte, O.; Kervyn, F.

2016-12-01

The western branch of the East African Rift System, in Central Africa, is a region naturally prone to landslides due to factors such as heavy rainfall, tectonic activity and steep topography. In addition, sensibility to slope instability is expected to increase in the future in response to increasing demographic pressure and land use/land cover changes. The Rift flanks west of Lake Kivu (DRC) are one of the Congolese regions most affected by landslides. Although heavy rainfall periods and earthquakes are the main triggering factors, nothing is known on their potential role on the current dynamics of existing landslides Here we used InSAR time series to monitor ground deformations associated to large slow-moving landslides that continuously affect highly populated slopes in the city of Bukavu (DRC). Bukavu is located within the Rift, on the southern shore of Lake Kivu, in a tropical environment. Using >100 Cosmo-SkyMed SAR images, acquired between March 2015 and June 2016 with a mean revisiting time of 8 days per orbit (ascending and descending), we produce displacement-rate maps and ground deformation time series using different techniques: Persistent Scatter (PS), Small Baseline Subset (SBAS) and Multidimensional Small Baseline Subsets (MSBAS). The three techniques provides similar results in areas with relatively small displacements (few mm per months). However, in areas where displacements are much higher and where coherence is lost by traditional techniques, MSBAS, that process concurrently the two satellite orbits improving temporal resolution, is more efficient. It allows to measure higher ground deformation rates by keeping the coherence. For one specific landslide where intense field mapping was done, the results show clearly the pattern of the deformations that divides the landslide in blocks that move with different velocity (up to 20 cm/yr). This pattern is consistent with field observations and possibly related to the anthropic activity. Furthermore, DGPS measurements, taken at 21 benchmarks in the area during the same period, allow validating the InSAR results. The combination of InSAR data with rainfall and seismic monitoring, and field observations should help us, when longer time-series will be available, to better understand the mechanisms (both natural and human) that affect this landslide.

Inflation-predictable behavior and co-eruption deformation at Axial Seamount.

PubMed

Nooner, Scott L; Chadwick, William W

2016-12-16

Deformation of the ground surface at active volcanoes provides information about magma movements at depth. Improved seafloor deformation measurements between 2011 and 2015 documented a fourfold increase in magma supply and confirmed that Axial Seamount's eruptive behavior is inflation-predictable, probably triggered by a critical level of magmatic pressure. A 2015 eruption was successfully forecast on the basis of this deformation pattern and marked the first time that deflation and tilt were captured in real time by a new seafloor cabled observatory, revealing the timing, location, and volume of eruption-related magma movements. Improved modeling of the deformation suggests a steeply dipping prolate-spheroid pressure source beneath the eastern caldera that is consistent with the location of the zone of highest melt within the subcaldera magma reservoir determined from multichannel seismic results. Copyright © 2016, American Association for the Advancement of Science.

Kilauea volcano, hawaii: a search for the volcanomagnetic effect.

PubMed

Davis, P M; Jackson, D B; Field, J; Stacey, F D

1973-04-06

Brief excursions of magnetic field differences between a base station and two satellite station magnetometers show only slight correlation with ground tilt at Kilauea Volcano. This result suggests that only transient, localized stresses occur during prolonged periods of deformation and that the volcano can support no large-scale pattern of shear stresses.

The evidences of progressive pressurization of volcanic conduit as driving forces of unrest phenomena analyzed via modelling of multiplatform geodetic measurements: Fernandina (GALAPAGOS) and Maunaloa (HAWAII) case studies

NASA Astrophysics Data System (ADS)

Pepe, Susi; Castaldo, Raffaele; Casu, Francesco; D'Auria, Luca; De Luca, Claudio; De Novellis, Vincenzo; Solaro, Giuseppe; Tizzani, Pietro

2017-04-01

We investigated the source of the ground deformation pattern affecting the Mauna Loa (Hawaii) and Fernandina (Galapagos) volcanoes by jointly exploiting different dataset collected by both GPS and multiplatform and multiorbit SAR sensors. We exploited the advanced Differential SAR Interferometry (DInSAR) techniques to analyze unrest episode in two different geodynamics context. Our main goal is the understanding of the relationship among the spatio-temporal evolution of the ground deformation field and the temporal volumetric variation of the detected geodetic source during the uplift phenomena. We highlight the huge opportunity in understanding volcano unrest phenomena offered by the joint use of remote sensing data and inversion procedures: this prospect is particularly relevant for the analysis of uplift events, when other geophysical measurements are not available. For Mauna Loa (Hawaii) and Fernandina (Galapagos) volcanoes, the performed statistic analysis support the source pipe-like as the more suitable geometry to explain the unrest phenomena in which magmatic masses intrude in volcanic conduits. In particular, the deformation time series achieved at MounaLoa volcano are achieved by 23 GPS permanent stations of the Hawaii surveillance network, processed by Nevada Geodetic Laboratory, 7 SAR dataset acquired from ascending and descending orbits, with different look angles and along different tracks, by the C-Band Envisat satellite along the 2003 - 2010 time period for a total of 189 SAR imagery. Moreover, we exploited 2 dataset collected from ascending and descending passes by the X-Band Cosmo Sky-Med constellation during the 2012 - 2015 time span . These SAR datasets have been processed through the advanced DInSAR technique referred to as P-SBAS (De Luca et al., 2016), which allows us to retrieve the Line of Sight (LOS) projection of the surface deformation and analyze its temporal evolution by generating displacement time series. Starting this data collection, we determined the source responsible of deformation observed and in particular the results of our inversions show that the pipe source contributes substantially to both the ground deformation pattern and the cost function. In the case of Fernandina Volcano (Galápagos) we exploited the advanced Differential SAR Interferometry (DInSAR) techniques to analyze the 2012-2013 uplift episode by using X-band data from the COSMO-SkyMed (CSK) satellite constellation. This volcano falls among those not well monitored, therefore, the availability of CSK data, acquired with a repeat time ranging from 4 to 12 days and with a ground resolution of 3 meters, represents a unique opportunity to perform a detailed study of the space and time ground deformation field changes (Sansosti et al., 2014). In addition, in this case study we computed the ground deformation time series by applying the Small BAseline Subset (SBAS)-DInSAR approach (Berardino et al., 2002) to CSK data, acquired from both ascending and descending orbits. The results of their combination (vertical and horizontal E-W components) are used in order to evaluate, through a cross correlation analysis (Tizzani et al., 2009; 2015), the volcanic areas that are characterized by similar uplift temporal behavior. Subsequently, we determine the geometry, location and the temporal evolution of the geodetic source responsible for the 2012 - 2013 uplift event by applying an inverse method to the DInSAR measurements. We search for its geometrical parameters and volume variation that minimize the difference between the observed data and the modelled ground deformation field. We tested various analytical models and finally, using the Akaike Information Criterion (Akaike, 1965) among the tested analytical sources, we selected the tilted pipe. The pipe model is similar to the prolate ellipsoid, but the size of the smaller axis is kept fixed to a very small value (i.e., 10 m). Despite having a similar fit with the prolate ellipsoid, the tilted pipe-like source has been selected because it has a lower number of degrees of freedom. Both vertical and E-W cross-correlated maps support the hypothesis of the existence of a single active source, characterized by a spatial stability over the entire considered time interval. Indeed, with the proposed source inversion procedure, we have shown that the inflation of a SE dipping tilted closed pipe-like pressurized source explains the observed ground deformation pattern very well. This result suggests that the observed uplift phenomenon could be produced by the progressive pressurization of a shallow elongated magma chamber, before the eruption onset phase. References Akaike, H. On the statistical estimation of the frequency response function of a system having multiple input. Ann. Inst. Stat. Math. 17, 185-210 (1965). Berardino, P., Fornaro, G., Lanari, R., Sansosti, E. (2002). A new algorithm for surface deformation monitoring based on small baseline differential SAR interferograms, IEEE Trans. Geosci. Remote Sens., 40, 2375-2383, doi:10.1109/TGRS.2002.803792. De Luca, C.; Cuccu, R.; Elefante, S.; Zinno, I.; Manunta, M.; Casola, V.; Rivolta, G.; Lanari, R.; Casu, F. An On-Demand Web Tool for the Unsupervised Retrieval of Earth's Surface Deformation from SAR Data: The P-SBAS Service within the ESA G-POD Environment. Remote Sens. 2015, 7, 15630-15650. Fialko, Y., Khazan, Y. and Simons, M. (2001), Deformation due to a pressurized horizontal circular crack in an elastic half-space, with applications to volcano geodesy. Geophysical Journal International, 146(1), 181-190 Mogi, K. (1958), Relations between the eruptions of various volcanoes and the deformations of the ground surfaces around them. Bulletin of the Earthquake Research Institute 36, 99-134. McTigue, D. F. (1987), Elastic stress and deformation near a finite spherical magma body: Resolution of the point source paradox. Journal of Geophysical Research: Solid Earth (1978-2012), 92(B12), 12931-12940. Okada, Y. Surface deformation due to shear and tensile faults in a half-space. Bull. Seism. Soc. Am. 75, 1135-1154 (1985). Sansosti, E., Berardino, P., Bonano, M., Calò, F., Castaldo, R., Casu, F., Manunta, M., Manzo, M., Pepe, A., Pepe, S., Solaro, G., Tizzani, P., Zeni, G., Lanari, R. (2014). How second generation SAR systems are impacting the analysis of ground deformation. International Journal of Applied Earth Observation and Geoinformation, 28, doi:10.1016/j.jag.2013.10.007. Tizzani, P., Battaglia, M., Zeni, G., Atzori, S., Berardino, P., Lanari, R. (2009). Uplift and magma intrusion at Long Valley caldera from InSAR and gravity measurements, Geology, January 2009 37; no.1; p. 63-66; doi:10.1130/G25318A.1 Tizzani, P., Battaglia, M., Castaldo, R., Pepe, A., Zeni, G., Lanari, R. (2015). Magma and fluid migration at Yellowstone Caldera in the last three decades inferred from InSAR, leveling, and gravity measurements. J. Geophys. Res. Solid Earth, 120, 2627-2647. doi: 10.1002/2014JB011502. Yang, X. M., Davis, P. M., and Dieterich, J. H. (1988), Deformation from inflation of a dipping finite prolate spheroid in an elastic half-space as a model for volcanic stressing. Journal of Geophysical Research: Solid Earth (1978-2012), 93(B5), 4249-4257.

Crustal Rebound due to Lake Mass Changes Measured by InSAR: Constraints on Lithosphere Rheology

NASA Astrophysics Data System (ADS)

Doin, M. P.; Twardzik, C.; Cavalié, O.; Lasserre, C.

2015-12-01

SAR interferometry has proven to be a reliable method for detecting small displacements due to ground subsidence. Here, we relate ground motion around the lake Mead (Nevada, USA) and lake Siling Co (Tibet, China) measured by InSAR to water loading in order to constrain the rheology of the lithosphere.Lake Mead, an artificial reservoir, has been filled with water in 1935. We analyzed ~500 interferograms based on 62 ERS images and on 40 ENVISAT images acquired between 1992 and 2010. Interferograms are inverted to solve for the time series of ground motion in the lake Mead area. Temporal smoothing allows to reduce the turbulent atmospheric delays. Spatio-temporal series of the deformation from 1992 to 2010 show a broad subsidence pattern correlated with lake level from 1992 to 2010. We model the deformation, taking into account the water and sediment loading history of the lake since 1935. The two-layer visco-elastic model proposed by Kaufmann and Amelung (2000), with a mantle viscosity of 1018 Pa s, adjusts well the data up to 2001, but overpredicts the deformation after 2001. We will discuss the models that could explain the deformation evolution. The Siling Co lake is the largest endorheic lake in Central Tibet. In 1972-1999 its water level remained stable, while it increased by about 1.0~m/yr in the period 2000-2006. The increased rate gradually stepped down to 0.2~m/yr in 2007-2011. We analysed 107 ERS and Envisat SAR images during the period 1992-2011. The deformation amplitude closely follows the lake level temporal evolution, except that subsidence continues in 2008-2011, while the lake level stagnated. This temporal evolution suggests a non elastic relaxation process taking place at a decade time-scale. Phase delay maps are used to constrain possible layered visco-elastic rheological models. An elastic model could partly explain the observed subsidence rate if elastic moduli are about twice lower than those extracted from Vp/Vs profiles. The surface deformation pattern is also extracted by projecting the phase delay maps againstthe best-fit model temporal behavior. It shows that deep relaxation in the asthenosphere is negligible at the decade time-scale andfavors the existence of a ductile (1-3x1018Pa.s) channel in the deep crust above a more rigid mantle.

Analogue Models Of Volcanic Spreading At Mt. Vesuvius

NASA Astrophysics Data System (ADS)

De Matteo, Ada; Castaldo, Raffaele; D'Auria, Luca; James, Michael; Lane, Steve; Massa, Bruno; Pepe, Susi; Tizzani, Pietro

2015-04-01

Somma-Vesuvius is a quiescent strato-volcano of the Neapolitan district, southern Italy, for which various geophysical and geological evidences (e.g. geodetic measurements, geological and structural data, seismic profiles interpretations and surface deformation analysis with Differential Interferometric Synthetic Aperture Radar (DInSAR)) indicate ongoing spreading deformation. In this research we investigate the spreading deformation and associated surface deformation pattern by performing analogue experiments and comparing the results with actual ground deformation as measured using DInSAR data recorded between 1992 and 2010. Somma-Vesuvius consists of a volcanic cone (Gran Cono) lying within an asymmetric caldera (Somma). The Somma caldera is the result of at least 7 Plinian eruptions, the last of which was the 79 CE. Pompeii eruption. The current cone of Mt. Vesuvius grew within the caldera in the following centuries as the effect of continued explosive and effusive activity of the volcano. The volcano lies on a substratum consisting of a Mesozoic carbonatic basement, overlapped by Holocene clastic sediments and volcanic rocks. Our analogue models were built to simulate the shape of the Somma-Vesuvius top a scale of about 1:100000, emplaced on a sand layer (brittle behaviour) laid on a silicone layer (ductile behaviour). Models are based on the Fluid-dynamics Dimensionless Analysis (FDA), according to the Buckingham-Π theorem. In this context, we considered few dimensionless parameters that allowed the setting of a reliable scaled model. To represent the complex Somma-Vesuvius geometry, an asymmetric model was built by setting a truncated cone (mimicking the topography of Somma edifice) topped by another small cone (mimicking the Gran Cono) shifted off the axis of the main cone. Different experiments were carried out in which the thickness of the basal sand layer and of the silicone one were varied. To quantify the vertical and horizontal displacements the models were monitored with three synchronised digital cameras, enabling sequential 3-D models to be derived using a photogrammetric technique. Finally, our models were compared with the 1992 - 2010 SBAS DInSAR measurements of ground deformations obtained using ERS-ENVISAT satellite images. The results show that analogue models are able to reproduce different styles of volcanic spreading and to reproduce the observed surface and deformation pattern. At the end our models show a deformation rather similar to the actual deformation pattern of the Somma-Vesuvius, both in the direction and in the intensity. Further studies will be devoted at find the best combination of parameters (silicone layer thickness and viscosity) to fit observations and to introduce a tridimensional rigid based topography. These studies will be implemented also with new structural and surface deformation (DinSAR) data and will be integrated with a numerical modelling.

Detection of ground deformation in the broader area of Sharm El- Shiekh (Sinai Peninsula, Egypt) by SAR interferometry

NASA Astrophysics Data System (ADS)

Seleem, Tarek A.; Foumelis, Michael; Parcharidis, Issaak

2009-09-01

Sharm El-Shiekh area is located in the most southern part of Sinai Peninsula boarded by the Gulf of Suez to the west and by the Gulf of Aqaba to the east. The present study concerns the application of Multibaseline/Stacking Differential SAR Interferometry (DInSAR) in order to monitor ground deformation rates in the southern part of Sharm El-Shiekh area. The specific technique was applied in order to reduce the influence of atmospheric effects on ground deformation estimates. For this purpose a total number of 24 ENVISAT ASAR scenes covering the period between 2002 and 2008 were processed and analysed. Interferometric results show both patterns of uplift and downlift in the study area. Specifically an area along the coastline with a N-S direction, corresponding to the build up zone of Sharm El-Shiekh, shows average annual subsidence rates between -5 and -7 mm/yr along the line of sight (LOS). On the contrary, Sharm El Maya, an inner zone parallel to the above subsided area, shows slant range uplift of around 5 mm/yr. The obtained results of SAR inteferometry probably indicate the presence of an active fault that affects the coastal zones of Sharm El-Shiekh area.

Inherited structures impact on co-seismic surface deformation pattern during the 2013 Balochistan, Pakistan, earthquake

NASA Astrophysics Data System (ADS)

Vallage, Amaury; Klinger, Yann; Grandin, Raphael; Delorme, Arthur; Pierrot-Deseilligny, Marc

2016-04-01

The understanding of earthquake processes and the interaction of earthquake rupture with Earth's free surface relies on the resolution of the observations. Recent and detailed post-earthquake measurements bring new insights on shallow mechanical behavior of rupture processes as it becomes possible to measure and locate surficial deformation distribution. The 2013 Mw 7.7 Balochistan earthquake, Pakistan, offers a nice opportunity to comprehend where and why surficial deformation might differs from at-depth localized slip. This earthquake ruptured the Hoshab fault over 200 km; the motion was mainly left lateral with a small and discontinuous vertical component in the southern part of the rupture. Using images with the finest resolution currently available, we measured the surface displacement amplitude and its orientation at the ground surface (including the numerous tensile cracks). We combined these measurements with the 1:500 scale ground rupture map to focus on the behavior of the frontal rupture in the area where deformation distributes. Comparison with orientations of inherited tectonic structures, visible in older rocks formation surrounding the actual 2013 rupture, shows the control exercised by such structures on co-seismic rupture distribution. Such observation raises the question on how pre-existing tectonic structures in a medium, mapped in several seismically active places around the globe; can control the co-seismic distribution of the deformation during earthquakes.

Exploring deformation scenarios in Timanfaya volcanic area (Lanzarote, Canary Islands) from GNSS and ground based geodetic observations

NASA Astrophysics Data System (ADS)

Riccardi, U.; Arnoso, J.; Benavent, M.; Vélez, E.; Tammaro, U.; Montesinos, F. G.

2018-05-01

We report on a detailed geodetic continuous monitoring in Timanfaya volcanic area (TVA), where the most intense geothermal anomalies of Lanzarote Island are located. We analyze about three years of GNSS data collected on a small network of five permanent stations, one of which at TVA, deployed on the island, and nearly 20 years of tiltmeter and strainmeter records acquired at Los Camelleros site settled in the facilities of the Geodynamics Laboratory of Lanzarote within TVA. This study is intended to contribute to understanding the active tectonics on Lanzarote Island and its origin, mainly in TVA. After characterizing and filtering out the seasonal periodicities related to "non-tectonic" sources from the geodetic records, a tentative ground deformation field is reconstructed through the analysis of both tilt, strain records and the time evolution of the baselines ranging the GNSS stations. The joint interpretation of the collected geodetic data show that the area of the strongest geothermal anomaly in TVA is currently undergoing a SE trending relative displacement at a rate of about 3 mm/year. This area even experiences a significant subsidence with a maximum rate of about 6 mm/year. Moreover, we examine the possible relation between the observed deformations and atmospheric effects by modelling the response functions of temperature and rain recorded in the laboratory. Finally, from the retrieval of the deformation patterns and the joint analysis of geodetic and environmental observations, we propose a qualitative model of the interplaying role between the hydrological systems and the geothermal anomalies. Namely, we explain the detected time correlation between rainfall and ground deformation because of the enhancement of the thermal transfer from the underground heat source driven by the infiltration of meteoric water.

Measuring structure deformations of a composite glider by optical means with on-ground and in-flight testing

NASA Astrophysics Data System (ADS)

Bakunowicz, Jerzy; Święch, Łukasz; Meyer, Ralf

2016-12-01

In aeronautical research experimental data sets of high quality are essential to verify and improve simulation algorithms. For this reason the experimental techniques need to be constantly refined. The shape, movement or deformation of structural aircraft elements can be measured implicitly in multiple ways; however, only optical, correlation-based techniques are able to deliver direct high-order and spatial results. In this paper two different optical metrologies are used for on-ground preparation and the actual execution of in-flight wing deformation measurements on a PW-6U glider. Firstly, the commercial PONTOS system is used for static tests on the ground and for wind tunnel investigations to successfully certify an experimental sensor pod mounted on top of the test bed fuselage. Secondly, a modification of the glider is necessary to implement the optical method named image pattern correlation technique (IPCT), which has been developed by the German Aerospace Center DLR. This scientific technology uses a stereoscopic camera set-up placed inside the experimental pod and a stochastic dot matrix applied to the area of interest on the glider wing to measure the deformation of the upper wing surface in-flight. The flight test installation, including the preparation, is described and results are presented briefly. Focussing on the compensation for typical error sources, the paper concludes with a recommended procedure to enhance the data processing for better results. Within the presented project IPCT has been developed and optimized for a new type of test bed. Adapted to the special requirements of the glider, the IPCT measurements were able to deliver a valuable wing deformation data base which now can be used to improve corresponding numerical models and simulations.

Characterization of open and closed volcanic systems in Indonesia and Mexico using InSAR time series

NASA Astrophysics Data System (ADS)

Chaussard, E.; Amelung, F.; Aoki, Y.

2013-08-01

use 2007-2011 Advanced Land Observing Satellite (ALOS) data to perform an arc-wide interferometric synthetic aperture radar (InSAR) time series survey of the Trans-Mexican Volcanic Belt (TMVB) and to study time-dependent ground deformation of four Indonesian volcanoes selected following the 2007-2009 study of Chaussard and Amelung (2012). Our objectives are to examine whether arc volcanoes exhibit long-term edifice-wide cyclic deformation patterns that can be used to characterize open and closed volcanic systems and to better constrain in which cases precursory inflation is expected. We reveal deformation cycles at both regularly active and previously inactive Indonesian volcanoes, but we do not detect deformation in the TMVB, reflecting a lower activity level. We identify three types of relationships between deformation and activity: inflation prior to eruption and associated with or followed by deflation (Kerinci and Sinabung), inflation without eruption and followed by slow deflation (Agung), and eruption without precursory deformation (Merapi, Colima, and Popocatépetl; at Merapi, no significant deformation is detected even during eruption). The first two cases correspond to closed volcanic systems and suggest that the traditional model of magmatic systems and eruptive cycles do apply to andesitic volcanoes (i.e., inflation and deflation episodes associated with magma accumulation or volatile exsolution in a crustal reservoir followed by eruptions or in situ cooling). In contrast, the last case corresponds to open volcanic systems where no significant pressurization of the magmatic reservoirs is taking place prior to eruptions and thus no long-term edifice-wide ground deformation can be detected. We discuss these results in terms of InSAR's potential for forecasting volcanic unrest.

TU-AB-BRA-09: A Novel Method of Generating Ultrafast Volumetric Cine MRI (VC-MRI) Using Prior 4D-MRI and On-Board Phase-Skipped Encoding Acquisition for Radiotherapy Target Localization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, C; Yin, F; Harris, W

Purpose: To develop a technique generating ultrafast on-board VC-MRI using prior 4D-MRI and on-board phase-skipped encoding k-space acquisition for real-time 3D target tracking of liver and lung radiotherapy. Methods: The end-of-expiration (EOE) volume in 4D-MRI acquired during the simulation was selected as the prior volume. 3 major respiratory deformation patterns were extracted through the principal component analysis of the deformation field maps (DFMs) generated between EOE and all other phases. The on-board VC-MRI at each instant was considered as a deformation of the prior volume, and the deformation was modeled as a linear combination of the extracted 3 major deformationmore » patterns. To solve the weighting coefficients of the 3 major patterns, a 2D slice was extracted from VC-MRI volume to match with the 2D on-board sampling data, which was generated by 8-fold phase skipped-encoding k-space acquisition (i.e., sample 1 phase-encoding line out of every 8 lines) to achieve an ultrafast 16–24 volumes/s frame rate. The method was evaluated using XCAT digital phantom to simulate lung cancer patients. The 3D volume of end-ofinhalation (EOI) phase at the treatment day was used as ground-truth onboard VC-MRI with simulated changes in 1) breathing amplitude and 2) breathing amplitude/phase change from the simulation day. A liver cancer patient case was evaluated for in-vivo feasibility demonstration. Results: The comparison between ground truth and estimated on-board VC-MRI shows good agreements. In XCAT study with changed breathing amplitude, the volume-percent-difference(VPD) between ground-truth and estimated tumor volumes at EOI was 6.28% and the Center-of-Mass-Shift(COMS) was 0.82mm; with changed breathing amplitude and phase, the VPD was 8.50% and the COMS was 0.54mm. The study of liver patient case also demonstrated a promising in vivo feasibility of the proposed method Conclusion: Preliminary results suggest the feasibility to estimate ultrafast VC-MRI for on-board target localization with phase skipped-encoding k-space acquisition. Research grant from NIH R01-184173.« less

Analytical magmatic source modelling from a joint inversion of ground deformation and focal mechanisms data

NASA Astrophysics Data System (ADS)

Cannavo', Flavio; Scandura, Danila; Palano, Mimmo; Musumeci, Carla

2014-05-01

Seismicity and ground deformation represent the principal geophysical methods for volcano monitoring and provide important constraints on subsurface magma movements. The occurrence of migrating seismic swarms, as observed at several volcanoes worldwide, are commonly associated with dike intrusions. In addition, on active volcanoes, (de)pressurization and/or intrusion of magmatic bodies stress and deform the surrounding crustal rocks, often causing earthquakes randomly distributed in time within a volume extending about 5-10 km from the wall of the magmatic bodies. Despite advances in space-based, geodetic and seismic networks have significantly improved volcano monitoring in the last decades on an increasing worldwide number of volcanoes, quantitative models relating deformation and seismicity are not common. The observation of several episodes of volcanic unrest throughout the world, where the movement of magma through the shallow crust was able to produce local rotation of the ambient stress field, introduces an opportunity to improve the estimate of the parameters of a deformation source. In particular, during these episodes of volcanic unrest a radial pattern of P-axes of the focal mechanism solutions, similar to that of ground deformation, has been observed. Therefore, taking into account additional information from focal mechanisms data, we propose a novel approach to volcanic source modeling based on the joint inversion of deformation and focal plane solutions assuming that both observations are due to the same source. The methodology is first verified against a synthetic dataset of surface deformation and strain within the medium, and then applied to real data from an unrest episode occurred before the May 13th 2008 eruption at Mt. Etna (Italy). The main results clearly indicate as the joint inversion improves the accuracy of the estimated source parameters of about 70%. The statistical tests indicate that the source depth is the parameter with the highest increment of accuracy. In addition a sensitivity analysis confirms that displacements data are more useful to constrain the pressure and the horizontal location of the source than its depth, while the P-axes better constrain the depth estimation.

Land subsidence due to groundwater pumping and recharge: considering the particle-deposition effect in ground-source heat-pump engineering

NASA Astrophysics Data System (ADS)

Cui, Xianze; Liu, Quansheng; Zhang, Chengyuan; Huang, Yisheng; Fan, Yong; Wang, Hongxing

2018-05-01

With the rapid development and use of ground-source heat-pump (GSHP) systems in China, it has become imperative to research the effects of associated long-term pumping and recharge processes on ground deformation. During groundwater GSHP operation, small particles can be transported and deposited, or they can become detached in the grain skeleton and undergo recombination, possibly causing a change in the ground structure and characteristics. This paper presents a mathematical ground-deformation model that considers particle transportation and deposition in porous media based on the geological characteristics of a dual-structure stratum in Wuhan, eastern China. Thermal effects were taken into consideration because the GSHP technology used involves a device that uses heat from a shallow layer of the ground. The results reveal that particle deposition during the long-term pumping and recharge process has had an impact on ground deformation that has significantly increased over time. In addition, there is a strong correlation between the deformation change (%) and the amount of particle deposition. The position of the maximum deformation change is also the location where most of the particles are deposited, with the deformation change being as high as 43.3%. The analyses also show that flow of groundwater can have an effect on the ground deformation process, but the effect is very weak.

Rapid dike intrusion into Sakurajima volcano on August 15, 2015, as detected by multi-parameter ground deformation observations

NASA Astrophysics Data System (ADS)

Hotta, Kohei; Iguchi, Masato; Tameguri, Takeshi

2016-04-01

We present observations of ground deformation at Sakurajima in August 2015 and model the deformation using a combination of GNSS, tilt and strain data in order to interpret a rapid deformation event on August 15, 2015. The pattern of horizontal displacement during the period from August 14 to 16, 2015, shows a WNW-ESE extension, which suggests the opening of a dike. Using a genetic algorithm, we obtained the position, dip, strike length, width and opening of a dislocation source based on the combined data. A nearly vertical dike with a NNE-SSW strike was found at a depth of 1.0 km below sea level beneath the Showa crater. The length and width are 2.3 and 0.6 km, respectively, and a dike opening of 1.97 m yields a volume increase of 2.7 × 106 m3. 887 volcano-tectonic (VT) earthquakes beside the dike suggest that the rapid opening of the dike caused an accumulation of strain in the surrounding rocks, and the VT earthquakes were generated to release this strain. Half of the total amount of deformation was concentrated between 10:27 and 11:54 on August 15. It is estimated that the magma intrusion rate was 1 × 106 m3/h during this period. This is 200 times larger than the magma intrusion rate prior to one of the biggest eruptions at the summit crater of Minami-dake on July 24, 2012, and 2200 times larger than the average magma intrusion rate during the period from October 2011 to March 2012. The previous Mogi-type ground deformation is considered to be a process of magma accumulation in preexisting spherical reservoirs. Conversely, the August 2015 event was a dike intrusion and occurred in a different location to the preexisting reservoirs. The direction of the opening of the dike coincides with the T-axes and direction of faults creating a graben structure.

Pattern of ground deformation in Kathmandu valley during 2015 Gorkha Earthquake, central Nepal

NASA Astrophysics Data System (ADS)

Ghimire, S.; Dwivedi, S. K.; Acharya, K. K.

2016-12-01

The 25th April 2015 Gorkha Earthquake (Mw=7.8) epicentered at Barpak along with thousands of aftershocks released seismic moment nearly equivalent to an 8.0 Magnitude earthquake rupturing a 150km long fault segment. Although Kathmandu valley was supposed to be severely devastated by such major earthquake, post earthquake scenario is completely different. The observed destruction is far less than anticipated as well as the spatial pattern is different than expected. This work focuses on the behavior of Kathmandu valley sediments during the strong shaking by the 2015 Gorkha Earthquake. For this purpose spatial pattern of destruction is analyzed at heavily destructed sites. To understand characteristics of subsurface soil 2D-MASW survey was carried out using a 24-channel seismograph system. An accellerogram recorded by Nepal Seismological Center was analyzed to characterize the strong ground motion. The Kathmandu valley comprises fluvio-lacustrine deposit with gravel, sand, silt and clay along with few exposures of basement rocks within the sediments. The observations show systematic repetition of destruction at an average interval of 2.5km mostly in sand, silt and clay dominated formations. Results of 2D-MASW show the sites of destruction are characterized by static deformation of soil (liquefaction and southerly dipping cracks). Spectral analysis of the accelerogram indicates maximum power associated with frequency of 1.0Hz. The result of this study explains the observed spatial pattern of destruction in Kathmandu valley. This is correlated with the seismic energy associated with the frequency of 1Hz, which generates an average wavelength of 2.5km with an average S-wave velocity of 2.5km/s. The cumulative effect of dominant frequency and associated wavelength resulted in static deformation of surface soil layers at an average interval of 2.5km. This phenomenon clearly describes the reason for different scenario than that was anticipated in Kathmandu valley.

Ground deformation associated with the March 1996 earthquake swarm at Akutan volcano, Alaska, revealed by satellite radar interferometry

USGS Publications Warehouse

Lu, Z.; Wicks, C.; Power, J.A.; Dzurisin, D.

2000-01-01

In March 1996 an intense swarm of volcano-tectonic earthquakes (???3000 felt by local residents, Mmax = 5.1, cumulative moment of 2.7 ??1018 N m) beneath Akutan Island in the Aleutian volcanic arc, Alaska, produced extensive ground cracks but no eruption of Akutan volcano. Synthetic aperture radar interferograms that span the time of the swarm reveal complex island-wide deformation: the western part of the island including Akutan volcano moved upward, while the eastern part moved downward. The axis of the deformation approximately aligns with new ground cracks on the western part of the island and with Holocene normal faults that were reactivated during the swarm on the eastern part of the island. The axis is also roughly parallel to the direction of greatest compressional stress in the region. No ground movements greater than 2.83 cm were observed outside the volcano's summit caldera for periods of 4 years before or 2 years after the swarm. We modeled the deformation primarily as the emplacement of a shallow, east-west trending, north dipping dike plus inflation of a deep, Mogi-type magma body beneath the volcano. The pattern of subsidence on the eastern part of the island is poorly constrained. It might have been produced by extensional tectonic strain that both reactivated preexisting faults on the eastern part of the island and facilitated magma movement beneath the western part. Alternatively, magma intrusion beneath the volcano might have been the cause of extension and subsidence in the eastern part of the island. We attribute localized subsidence in an area of active fumaroles within the Akutan caldera, by as much as 10 cm during 1992-1993 and 1996-1998, to fluid withdrawal or depressurization of the shallow hydrothermal system. Copyright 2000 by the American Geophysical Union.

A Method for Assessing Ground-Truth Accuracy of the 5DCT Technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dou, Tai H., E-mail: tdou@mednet.ucla.edu; Thomas, David H.; O'Connell, Dylan P.

2015-11-15

Purpose: To develop a technique that assesses the accuracy of the breathing phase-specific volume image generation process by patient-specific breathing motion model using the original free-breathing computed tomographic (CT) scans as ground truths. Methods: Sixteen lung cancer patients underwent a previously published protocol in which 25 free-breathing fast helical CT scans were acquired with a simultaneous breathing surrogate. A patient-specific motion model was constructed based on the tissue displacements determined by a state-of-the-art deformable image registration. The first image was arbitrarily selected as the reference image. The motion model was used, along with the free-breathing phase information of the originalmore » 25 image datasets, to generate a set of deformation vector fields that mapped the reference image to the 24 nonreference images. The high-pitch helically acquired original scans served as ground truths because they captured the instantaneous tissue positions during free breathing. Image similarity between the simulated and the original scans was assessed using deformable registration that evaluated the pointwise discordance throughout the lungs. Results: Qualitative comparisons using image overlays showed excellent agreement between the simulated images and the original images. Even large 2-cm diaphragm displacements were very well modeled, as was sliding motion across the lung–chest wall boundary. The mean error across the patient cohort was 1.15 ± 0.37 mm, and the mean 95th percentile error was 2.47 ± 0.78 mm. Conclusion: The proposed ground truth–based technique provided voxel-by-voxel accuracy analysis that could identify organ-specific or tumor-specific motion modeling errors for treatment planning. Despite a large variety of breathing patterns and lung deformations during the free-breathing scanning session, the 5-dimensionl CT technique was able to accurately reproduce the original helical CT scans, suggesting its applicability to a wide range of patients.« less

Reconstructing the internal structure and long-term evolution of hazardous sinkholes combining trenching, electrical resistivity imaging (ERI) and ground penetrating radar (GPR)

NASA Astrophysics Data System (ADS)

Fabregat, Ivan; Gutiérrez, Francisco; Roqué, Carles; Comas, Xavier; Zarroca, Mario; Carbonel, Domingo; Guerrero, Jesús; Linares, Rogelio

2017-05-01

The approaches aimed at characterising specific damaging sinkholes have received limited attention compared with other ground instability phenomena (e.g. landslides). Moreover, the practicality of the trenching technique in combination with numerical dating and retro-deformation analysis for sinkhole site-investigations has been barely explored. This work illustrates the advantages of combining geomorphic mapping, electrical resistivity imaging (ERI), ground penetrating radar (GPR) and trenching for sinkhole characterisation and shows how the trenching technique contributes to fill significant gaps that neither geomorphic nor geophysical methods can address. Two large sinkholes (> 200 m long) related to the interstratal karstification of evaporites and generated by contrasting subsidence mechanisms (sagging, collapse) were investigated in the Fluvia Valley, NE Spain. Although GPR data may provide high resolution information on subsidence-related stratigraphic and structural features at shallow depth, the profiles acquired in the investigated sites with 100 MHz shielded and 40 MHz unshielded antennae provided limited insight into the internal geometry of the sinkholes due to reduced signal penetration related to the presence of conductive clayey material. The ERI sections satisfactorily imaged the general geometry of the sagging and collapse subsidence structures up to depths higher than 100 m and clearly captured the basal contact of the low-resistivity sinkhole fill in the sections with adequate layout and resolution. The trenches, despite their limited depth (ca. 5 m) allowed us to obtain valuable objective information on several key aspects of the subsidence phenomenon: (1) mechanisms (deformation style) and kinematics (progressive versus episodic); (2) limits of ground deformation; (3) temporal evolution (expansion versus contraction); (4) chronology and timing of most recent deformation phase; (5) rates of subsidence and sedimentation; and (6) the role played by subsidence in the development of lacustrine environments and the associated sedimentation patterns.

Spin-dependent γ softness or triaxiality in even-even 132-138Nd nuclei

NASA Astrophysics Data System (ADS)

Chai, Qing-Zhen; Wang, Hua-Lei; Yang, Qiong; Liu, Min-Liang

2015-02-01

The properties of γ instability in rapidly rotating even-even 132-138Nd isotopes have been investigated using the pairing-deformation self-consistent total-Routhian-surface calculations in a deformation space of (β2, γ, β4). It is found that even-even 134-138Nd nuclei exhibit triaxiality in both ground and excited states, even up to high-spin states. The lightest isotope possesses a well-deformed prolate shape without a γ deformation component. The current numerical results are compared with previous calculations and available observables such as quadrupole deformation β2 and the feature of γ-band levels, showing basically a general agreement with the observed trend of γ correlations (e.g. the pattern of the odd-even energy staggering of the γ band). The existing differences between theory and experiment are analyzed and discussed briefly. Supported by National Natural Science Foundation of China (10805040,11175217), Foundation and Advanced Technology Research Program of Henan Province(132300410125) and S & T Research Key Program of Henan Province Education Department (13A140667)

Atmospheric tomography using a fringe pattern in the sodium layer.

PubMed

Baharav, Y; Ribak, E N; Shamir, J

1994-02-15

We wish to measure and separate the contribution of atmospheric turbulent layers for multiconjugate adaptive optics. To this end, we propose to create a periodic fringe pattern in the sodium layer and image it with a modified Hartmann sensor. Overlapping sections of the fringes are imaged by a lenslet array onto contiguous areas in a large-format camera. Low-layer turbulence causes an overall shift of the fringe pattern in each lenslet, and high-attitude turbulence results in internal deformations in the pattern. Parallel Fourier analysis permits separation of the atmospheric layers. Two mirrors, one conjugate to a ground layer and the other conjugate to a single high-altitude layer, are shown to widen the field of view significantly compared with existing methods.

Geological structures control on earthquake ruptures: The Mw7.7, 2013, Balochistan earthquake, Pakistan

NASA Astrophysics Data System (ADS)

Vallage, A.; Klinger, Y.; Lacassin, R.; Delorme, A.; Pierrot-Deseilligny, M.

2016-10-01

The 2013 Mw7.7 Balochistan earthquake, Pakistan, ruptured the Hoshab fault. Left-lateral motion dominated the deformation pattern, although significant vertical motion is found along the southern part of the rupture. Correlation of high-resolution (2.5 m) optical satellite images provided horizontal displacement along the entire rupture. In parallel, we mapped the ground rupture geometry at 1:500 scale. We show that the azimuth of the ground rupture distributes mainly between two directions, N216° and N259°. The direction N216° matches the direction of preexisting geologic structures resulting from penetrative deformation caused by the nearby Makran subduction. Hence, during a significant part of its rupture, the 2013 Balochistan rupture kept switching between a long-term fault front and secondary branches, in which existence and direction are related to the compressional context. It shows unambiguous direct interactions between different preexisting geologic structures, regional stress, and dynamic-rupture stress, which controlled earthquake propagation path.

Long-term ground deformation patterns of Bucharest using multi-temporal InSAR and multivariate dynamic analyses: a possible transpressional system?

PubMed Central

Armaş, Iuliana; Mendes, Diana A.; Popa, Răzvan-Gabriel; Gheorghe, Mihaela; Popovici, Diana

2017-01-01

The aim of this exploratory research is to capture spatial evolution patterns in the Bucharest metropolitan area using sets of single polarised synthetic aperture radar (SAR) satellite data and multi-temporal radar interferometry. Three sets of SAR data acquired during the years 1992–2010 from ERS-1/-2 and ENVISAT, and 2011–2014 from TerraSAR-X satellites were used in conjunction with the Small Baseline Subset (SBAS) and persistent scatterers (PS) high-resolution multi-temporal interferometry (InSAR) techniques to provide maps of line-of-sight displacements. The satellite-based remote sensing results were combined with results derived from classical methodologies (i.e., diachronic cartography) and field research to study possible trends in developments over former clay pits, landfill excavation sites, and industrial parks. The ground displacement trend patterns were analysed using several linear and nonlinear models, and techniques. Trends based on the estimated ground displacement are characterised by long-term memory, indicated by low noise Hurst exponents, which in the long-term form interesting attractors. We hypothesize these attractors to be tectonic stress fields generated by transpressional movements. PMID:28252103

Long-term ground deformation patterns of Bucharest using multi-temporal InSAR and multivariate dynamic analyses: a possible transpressional system?

PubMed

Armaş, Iuliana; Mendes, Diana A; Popa, Răzvan-Gabriel; Gheorghe, Mihaela; Popovici, Diana

2017-03-02

The aim of this exploratory research is to capture spatial evolution patterns in the Bucharest metropolitan area using sets of single polarised synthetic aperture radar (SAR) satellite data and multi-temporal radar interferometry. Three sets of SAR data acquired during the years 1992-2010 from ERS-1/-2 and ENVISAT, and 2011-2014 from TerraSAR-X satellites were used in conjunction with the Small Baseline Subset (SBAS) and persistent scatterers (PS) high-resolution multi-temporal interferometry (InSAR) techniques to provide maps of line-of-sight displacements. The satellite-based remote sensing results were combined with results derived from classical methodologies (i.e., diachronic cartography) and field research to study possible trends in developments over former clay pits, landfill excavation sites, and industrial parks. The ground displacement trend patterns were analysed using several linear and nonlinear models, and techniques. Trends based on the estimated ground displacement are characterised by long-term memory, indicated by low noise Hurst exponents, which in the long-term form interesting attractors. We hypothesize these attractors to be tectonic stress fields generated by transpressional movements.

Generation of Escher Arts with Dual Perception.

PubMed

Lin, Shih-Syun; Morace, Charles C; Lin, Chao-Hung; Hsu, Li-Fong; Lee, Tong-Yee

2018-02-01

Escher transmutation is a graphic art that smoothly transforms one tile pattern into another tile pattern with dual perception. A classic example is the artwork called Sky and Water, in which a compelling figure-ground arrangement is applied to portray the transmutation of a bird in sky and a fish in water. The shape of a bird is progressively deformed and dissolves into the background while the background gradually reveals the shape of a fish. This paper introduces a system to create a variety of Escher-like transmutations, which includes the algorithms for initializing a tile pattern with dual figure-ground arrangement, for searching for the best matched shape of a user-specified motif from a database, and for transforming the content and shapes of tile patterns using a content-aware warping technique. The proposed system, integrating the graphic techniques of tile initialization, shape matching, and shape warping, allows users to create various Escher-like transmutations with minimal user interaction. Experimental results and conducted user studies demonstrate the feasibility and flexibility of the proposed system in Escher art generation.

Analysis of recent surface deformation at Ischia Island Volcano (South Italy) via multi-platform monitoring systems

NASA Astrophysics Data System (ADS)

Manzo, Mariarosaria; De Martino, Prospero; Castaldo, Raffaele; De Luca, Claudio; Dolce, Mario; Scarpato, Giovanni; Tizzani, Pietro; Zinno, Ivana; Lanari, Riccardo

2017-04-01

Ischia Island is a densely populated volcanic area located in the North-Western sector of the Gulf of Napoli (South Italy), whose activity is characterized by eruptions (the last one occurred in 1302 A.D.), earthquakes (the most disastrous ones occurred in 1881 and in 1883), fumarolic-hydrothermal manifestations and ground deformation. In this work we carry out the surface deformation time-series analysis occurring at the Island by jointly exploiting data collected via two different monitoring systems. In particular, we take advantage from the large amount of periodic and continuous geodetic measurements collected by the GPS (campaign and permanent) stations deployed on the Island and belonging to the INGV-OV monitoring network. Moreover, we benefit from the large, free and open archive of C-band SAR data acquired over the Island by the Sentinel-1 constellation of the Copernicus Program, and processed via the advanced Differential SAR Interferometry (DInSAR) technique referred to as Small BAseline Subset (SBAS) algorithm [Berardino et al., 2002]. We focus on the 2014-2017 time period to analyze the recent surface deformation phenomena occurring on the Island, thus extending a previous study, aimed at investigating the temporal evolution of the ground displacements affecting the Island and limited to the 1992-2003 time interval [Manzo et al., 2006]. The performed integrated analysis provides relevant spatial and temporal information on the Island surface deformation pattern. In particular, it reveals a rather complex deformative scenario, where localized phenomena overlap/interact with a spatially extended deformation pattern that involves many Island sectors, with no evidence of significant uplift phenomena. Moreover, it shows a good agreement and consistency between the different kinds of data, thus providing a clear picture of the recent dynamics at Ischia Island that can be profitably exploited to deeply investigate the physical processes behind the observed deformation phenomena. Acknowledgments This work is partially supported by the IREA-CNR/Italian Department of Civil Protection agreement and the I-AMICA project (Infrastructure of High Technology for Environmental and Climate Monitoring-PONa3_00363). References Berardino, P., G. Fornaro, R. Lanari, and E. Sansosti (2002), A new algorithm for surface deformation monitoring based on small baseline differential SAR interferograms, IEEE Trans. Geosci. Remote Sens., 40, 2375-2383, doi:10.1109/TGRS.2002.803792. Manzo, M., G. P. Ricciardi, F. Casu, G. Ventura, G. Zeni, S. Borgström, P. Berardino, C. Del Gaudio, and R. Lanari (2006), Surface deformation analysis in the Ischia Island (Italy) based on spaceborne radar interferometry, Journal of Volcanology and Geothermal Research, 151, 399-416, doi:10.1016/j.jvolgeores.2005.09.010.

The use of the Finite Element method for the earthquakes modelling in different geodynamic environments

NASA Astrophysics Data System (ADS)

Castaldo, Raffaele; Tizzani, Pietro

2016-04-01

Many numerical models have been developed to simulate the deformation and stress changes associated to the faulting process. This aspect is an important topic in fracture mechanism. In the proposed study, we investigate the impact of the deep fault geometry and tectonic setting on the co-seismic ground deformation pattern associated to different earthquake phenomena. We exploit the impact of the structural-geological data in Finite Element environment through an optimization procedure. In this framework, we model the failure processes in a physical mechanical scenario to evaluate the kinematics associated to the Mw 6.1 L'Aquila 2009 earthquake (Italy), the Mw 5.9 Ferrara and Mw 5.8 Mirandola 2012 earthquake (Italy) and the Mw 8.3 Gorkha 2015 earthquake (Nepal). These seismic events are representative of different tectonic scenario: the normal, the reverse and thrust faulting processes, respectively. In order to simulate the kinematic of the analyzed natural phenomena, we assume, under the plane stress approximation (is defined to be a state of stress in which the normal stress, sz, and the shear stress sxz and syz, directed perpendicular to x-y plane are assumed to be zero), the linear elastic behavior of the involved media. The performed finite element procedure consist of through two stages: (i) compacting under the weight of the rock successions (gravity loading), the deformation model reaches a stable equilibrium; (ii) the co-seismic stage simulates, through a distributed slip along the active fault, the released stresses. To constrain the models solution, we exploit the DInSAR deformation velocity maps retrieved by satellite data acquired by old and new generation sensors, as ENVISAT, RADARSAT-2 and SENTINEL 1A, encompassing the studied earthquakes. More specifically, we first generate 2D several forward mechanical models, then, we compare these with the recorded ground deformation fields, in order to select the best boundaries setting and parameters. Finally, the performed multi-parametric finite element models allow us to verify the effect of the crustal structures on the ground deformation and evaluate the stress-drop associated to the studied earthquakes on the surrounding structures.

Locally distributed ground deformation in an area of potential phreatic eruption, Midagahara volcano, Japan, detected by single-look-based InSAR time series analysis

NASA Astrophysics Data System (ADS)

Kobayashi, Tomokazu

2018-05-01

Although it is difficult to monitor the spatial extent and temporal evolution of local and small-magnitude ground inflation, this information is vital to assess the potential for phreatic eruption. Herein, we demonstrate the detection of locally distributed ground deformation preceding the enhancement of geothermal activity in the Midagahara volcano, Japan, through the application of single-look-based interferometric synthetic aperture radar analysis. In the Jigoku-dani geothermal area, the ground deformation proceeded at a low speed of 4 cm/year at most with a spatial extent of 500 m in the east-west direction and 250 m in the north-south direction. The deformation can be recognized to progress from 2007, at the latest, to 2010, after which the geothermal activity increased, with the collapse of sulfur towers and the appearance of active fumaroles and boiling water on the ground surface. The most deformed area corresponds to the geothermal area with the highest activity observed on the ground surface. Assuming a sill opening model, the deformation source is estimated to be located at a depth of 50 m from the surface with a speed of 7 cm/year at most, which is consistent with the depth of the highly conductive medium inferred from magnetotelluric analyses. This may suggest that volcanic fluid and/or heat was injected into the fluid-rich medium from depth and caused the ground inflation. Our results demonstrate that high-spatial-resolution deformation data can be an effective tool to monitor subsurface pressure conditions with pinpoint spatial accuracy during the build-up to phreatic eruptions.

Persistent summit subsidence at Volcán de Colima, México, 1982 1999: strong evidence against Mogi deflation

NASA Astrophysics Data System (ADS)

Murray, John B.; Wooller, Luke K.

2002-09-01

This paper re-examines recent ground-deformation measurements at Volcán de Colima, Mexico, to test the hypothesis that the observed movements are in response to pressure changes within a sub-volcanic magma chamber, as suggested for other volcanoes by [Mogi (1958) Earthq. Res. Inst. 36, 99-134]. Measurements of vertical ground deformation across the summit dome complex of Volcán de Colima from a precise levelling network between 1982 and 1999, together with vertical and horizontal displacements derived from dual-frequency GPS measurements in 1994 and 1997, show continuous subsidence. The deformation pattern derived from the levelling shows that subsidence increases towards the summit. The closest stations to the summit (1.1 km distant) show a mean subsidence rate of 5 mm per year compared to the reference station at 2.3 km distance, which may be subsiding itself. Vertical displacements of individual stations since 1982 show that the subsidence has been fairly continuous. The GPS stations, which are distributed more widely and include some close to the edge of the active dome, confirm summit subsidence. The largest measured value, a decrease of 280 mm, or 93 mm subsidence per year, was obtained at the edge of the dome. Horizontal displacements measured during 1994-1997 also show the largest values at the summit, but these are much smaller than the vertical displacements, with the maximum rate of 23 mm per year recorded close to the dome. It is conclusively shown that these measured movements cannot be due to deflation of a buried Mogi source, as vertical and horizontal displacements for some stations are in contrary directions to those predicted by the model, and there is no consistent pattern to the horizontal movements. We attribute the measured deformation to downslope creep, settling and compaction of the edifice, gravitational spreading, or a combination of these processes.

Crustal subsidence, seismicity, and structure near Medicine Lake Volcano, California

USGS Publications Warehouse

Dzurisin, D.; Donnelly-Nolan, J. M.; Evans, J.R.; Walter, S.R.

1991-01-01

The pattern of historical ground deformation, seismicity, and crustal structure near Medicine Lake volcano illustrates a close relation between magmatism and tectonism near the margin of the Cascade volcanic chain and the Basin and Range tectonic province. Subsidence occurs mainly by aseismic creep within 25km of the summit, where the crust has been heated and weakened by intrusions, and by normal faulting during episodic earthquake swarms in surrounding, cooler terrain. -from Authors

Volcanic deformation of Atosanupuri volcanic complex in the Kussharo caldera, Japan, from 1993 to 2016 revealed by JERS-1, ALOS, and ALOS-2 radar interferometry

NASA Astrophysics Data System (ADS)

Fujiwara, Satoshi; Murakami, Makoto; Nishimura, Takuya; Tobita, Mikio; Yarai, Hiroshi; Kobayashi, Tomokazu

2017-06-01

A series of uplifts and subsidences of a volcanic complex in the Kussharo caldera in eastern Hokkaido (Japan) has been revealed by interferometric analysis using archived satellite synthetic aperture radar data. A time series of interferograms from 1993 to 1998 showed the temporal evolution of a ground deformation process. The horizontal dimension of the deformation field was about 10 km in diameter, and the maximum amplitude of the deformation was >20 cm. Uplift started in 1994, and concurrent earthquake swarm activity was observed around the uplift area; however, no other phenomena were observed during this period. A subsidence process then followed, with the shape of the deformation forming a mirror image of the uplift. Model simulations suggest deformation was caused by a source at the depth of about 6 km and that the position of the source remained static throughout the episode. Subsidence of the volcanic complex was also observed by another satellite from 2007 to 2010, and likely continued for more than 10 years. In addition to the main uplift-subsidence sequence, small deformation patterns with short spatial wavelengths were observed at the center of the deforming area. Data from three satellites recorded small-scale subsidence of the Atosanupuri and Rishiri lava domes at a constant rate of approx. 1 cm/year from 1993 to 2016.[Figure not available: see fulltext.

Winnetka deformation zone: Surface expression of coactive slip on a blind fault during the Northridge earthquake sequence, California. Evidence that coactive faulting occurred in the Canoga Park, Winnetka, and Northridge areas during the 17 January 1994, Northridge, California earthquake

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cruikshank, K.M.; Johnson, A.M.; Fleming, R.W.

1996-12-31

Measurements of normalized length changes of streets over an area of 9 km{sup 2} in San Fernando Valley of Los Angeles, California, define a distinctive strain pattern that may well reflect blind faulting during the 1994 Northridge earthquake. Strain magnitudes are about 3 {times} 10{sup {minus}4}, locally 10{sup {minus}3}. They define a deformation zone trending diagonally from near Canoga Park in the southwest, through Winnetka, to near Northridge in the northeast. The deformation zone is about 4.5 km long and 1 km wide. The northwestern two-thirds of the zone is a belt of extension of streets, and the southeastern one-thirdmore » is a belt of shortening of streets. On the northwest and southeast sides of the deformation zone the magnitude of the strains is too small to measure, less than 10{sup {minus}4}. Complete states of strain measured in the northeastern half of the deformation zone show that the directions of principal strains are parallel and normal to the walls of the zone, so the zone is not a strike-slip zone. The magnitudes of strains measured in the northeastern part of the Winnetka area were large enough to fracture concrete and soils, and the area of larger strains correlates with the area of greater damage to such roads and sidewalks. All parts of the pattern suggest a blind fault at depth, most likely a reverse fault dipping northwest but possibly a normal fault dipping southeast. The magnitudes of the strains in the Winnetka area are consistent with the strains produced at the ground surface by a blind fault plane extending to depth on the order of 2 km and a net slip on the order of 1 m, within a distance of about 100 to 500 m of the ground surface. The pattern of damage in the San Fernando Valley suggests a fault segment much longer than the 4.5 km defined by survey data in the Winnetka area. The blind fault segment may extend several kilometers in both directions beyond the Winnetka area. This study of the Winnetka area further supports observations that a large earthquake sequence can include rupture along both a main fault and nearby faults with quite different senses of slip. Faults near the main fault that approach the ground surface or cut the surface in an area have the potential of moving coactively in a major earthquake. Movement on such faults is associated with significant damage during an earthquake. The fault that produced the main Northridge shock and the faults that moved coactively in the Northridge area probably are parts of a large structure. Such interrelationships may be key to understanding earthquakes and damage caused by tectonism.« less

Deformation patterns, magma supply, and magma storage at Karymsky Volcanic Center, Kamchatka, Russia, 2000-2010, revealed by InSAR

NASA Astrophysics Data System (ADS)

Ji, Lingyun; Izbekov, Pavel; Senyukov, Sergey; Lu, Zhong

2018-02-01

Under a complex geological region influenced by the subduction of the Pacific plate, Kamchatka Peninsula is one of the most active volcanic arcs in the Pacific Rim. Due to logistical difficulty in instrumentation, shallow magma plumbing systems beneath some of the Kamchatkan volcanoes are poorly understood. InSAR offers a safe and quick method for monitoring volcanic deformation with a high spatial resolution. In this study, a group of satellite radar interferograms that span the time interval from 2000 to 2010 shows eruptive and non-eruptive deformation at Karymsky Volcanic Center (KVC), Kamchatka, Russia. All the interferograms provide details of the activity around the KVC during 2000-2010, as follows: (1) from 2000 to 2004, the Karymsky-AN (Akademia Nauk) area deflated and the MS (Maly Semyachik) area inflated, (2) from 2004 to 2006, the Karymsky-AN area deflated with ongoing eruption, while the MS area subsided without eruption, (3) from 2006 to 2008, as with 2000-2004, the Karymsky-AN area deflated and the MS area inflated, (4) from 2008 to 2010, the Karymsky-AN area inflated up to 3 cm, and the MS area subsided. Point source models suggest that two magma reservoirs provide a good fit to the observed deformation. One source is located beneath the area between Karymsky and AN at a depth of approximately 7.0 km, and the other one is situated beneath MS at a depth of around 5.8 km. Synchronous deformation patterns suggest that two magma systems are fed from the same deep magma source and connected by a fracture zone. The InSAR results are consistent with GPS ground deformation measurements, seismic data, and petrological constraints.

Water induced geohazards measured with spaceborne interferometry techniques

NASA Astrophysics Data System (ADS)

Poncos, V.; Serban, F.; Teleaga, D.; Ciocan, V.; Sorin, M.; Caranda, D.; Zamfirescu, F.; Andrei, M.; Copaescu, S.; Radu, M.; Raduca, V.

2012-04-01

Natural and anthropogenic occurrence of groundwater is inducing surficial crustal deformation processes that can be accurately measured with high spatial density from space, regardless of the ground access conditions. The detection of the surface deformation allows uncovering spatial and temporal patterns of subsurface processes such as land subsidence, cave-ins and differential ground settlement related to water content. InSAR measurements combined with ground truth data permit estimation of the mechanical properties of the rocks and the development of models and scenarios to predict disaster events such as cave-ins, landslides and soil liquefaction in the case of an Earthquake. A number of three sites in Romania that suffer of ground instability because of the water component will be presented. The DInSAR, Interferograms Stacking and Persistent Scatterers Interferometry techniques were applied to retrieve as accurate as possible the displacement information. The first studied site is the city of Bucharest; using 7 years of ERS data ground instability was detected on a large area that represents the historical watershed of the Dambovita river. A network of water wells shows that the ground instability is directly proportional to the groundwater depth. The second site is the Ocnele Mari brine extraction area. The exploitation of the Ocnele Mari salt deposit started from the Roman Empire time using the mining technology and from 1954 the salt dissolution technology which involves injecting water into the ground using a well and extracting the brine (water and salt) through another well. The extraction of salt through dissolution led to slow ground subsidence but the flooding and dissolution of the Roman caves led to catastrophic cave-ins and the relocation of an entire village. The water injection technique is still applied and the Roman cave system is an unknown, therefore further catastrophic events are expected. The existing theoretical simulations of the subsidence process are performed using a Finite Element Method (FEM), which calculates the distribution of the state of strains and stresses in the rock masses, in an elasto-plastic behavior. The ground deformation is presently measured with leveling instrumentation and an effort is being made to adopt the InSAR results for a better spatial and temporal coverage that should refine the existing model. The third site is a number of 4 tailing retention ponds at different stages of their life. The tailing ponds are hydrotechnical structures of permeable type designed for the safe storage of mining detritus byproducts and disposal of the water contained in these byproducts. Starting in 1998 approximately 550 mines have been closed and introduced in a conservation process. In order to prevent ecological and human damage, all these mines and storage ponds for mining tailings are required to be under continuous monitoring. Using 15 high-resolution Spotlight TerraSAR-X images, the stability of the storage pond was monitored over a period of 5 months during 2011. Interferometric stacking techniques and PSI analysis were applied in order to generate deformation maps and deformation profiles. In the same time, GPS measurements and Electrical Tomography for water content were used as independent measurements.

Mapping ground surface deformation using temporarily coherent point SAR interferometry: Application to Los Angeles Basin

USGS Publications Warehouse

Zhang, L.; Lu, Zhong; Ding, X.; Jung, H.-S.; Feng, G.; Lee, C.-W.

2012-01-01

Multi-temporal interferometric synthetic aperture radar (InSAR) is an effective tool to detect long-term seismotectonic motions by reducing the atmospheric artifacts, thereby providing more precise deformation signal. The commonly used approaches such as persistent scatterer InSAR (PSInSAR) and small baseline subset (SBAS) algorithms need to resolve the phase ambiguities in interferogram stacks either by searching a predefined solution space or by sparse phase unwrapping methods; however the efficiency and the success of phase unwrapping cannot be guaranteed. We present here an alternative approach – temporarily coherent point (TCP) InSAR (TCPInSAR) – to estimate the long term deformation rate without the need of phase unwrapping. The proposed approach has a series of innovations including TCP identification, TCP network and TCP least squares estimator. We apply the proposed method to the Los Angeles Basin in southern California where structurally active faults are believed capable of generating damaging earthquakes. The analysis is based on 55 interferograms from 32 ERS-1/2 images acquired during Oct. 1995 and Dec. 2000. To evaluate the performance of TCPInSAR on a small set of observations, a test with half of interferometric pairs is also performed. The retrieved TCPInSAR measurements have been validated by a comparison with GPS observations from Southern California Integrated GPS Network. Our result presents a similar deformation pattern as shown in past InSAR studies but with a smaller average standard deviation (4.6 mm) compared with GPS observations, indicating that TCPInSAR is a promising alternative for efficiently mapping ground deformation even from a relatively smaller set of interferograms.

Residual settlements detection of ocean reclaimed lands with multi-platform SAR time series and SBAS technique: a case study of Shanghai Pudong International Airport

NASA Astrophysics Data System (ADS)

Yu, Lei; Yang, Tianliang; Zhao, Qing; Pepe, Antonio; Dong, Hongbin; Sun, Zhibin

2017-09-01

Shanghai Pudong International airport is one of the three major international airports in China. The airport is located at the Yangtze estuary which is a sensitive belt of sea and land interaction region. The majority of the buildings and facilities in the airport are built on ocean-reclaimed lands and silt tidal flat. Residual ground settlement could probably occur after the completion of the airport construction. The current status of the ground settlement of the airport and whether it is within a safe range are necessary to be investigated. In order to continuously monitor the ground settlement of the airport, two Synthetic Aperture Radar (SAR) time series, acquired by X-band TerraSAR-X (TSX) and TanDEM-X (TDX) sensors from December 2009 to December 2010 and from April 2013 to July 2015, were used for analyzing with SBAS technique. We firstly obtained ground deformation measurement of each SAR subset. Both of the measurements show that obvious ground subsidence phenomenon occurred at the airport, especially in the second runway, the second terminal, the sixth cargo plane and the eighth apron. The maximum vertical ground deformation rates of both SAR subset measurements were greater than -30 mm/year, while the cumulative ground deformations reached up to -30 mm and -35 mm respectively. After generation of SBAS-retrieved ground deformation for each SAR subset, we performed a joint analysis to combine time series of each common coherent point by applying a geotechnical model. The results show that three centralized areas of ground deformation existed in the airport, mainly distributed in the sixth cargo plane, the fifth apron and the fourth apron, The maximum vertical cumulative ground subsidence was more than -70 mm. In addition, by analyzing the combined time series of four selected points, we found that the ground deformation rates of the points located at the second runway, the third runway, and the second terminal, were progressively smaller as time goes by. It indicates that the stabilities of the foundation around these points were gradually enhanced.

Stability Evaluation of Buildings in Urban Area Using Persistent Scatterer Interfometry -Focused on Thermal Expansion Effect

NASA Astrophysics Data System (ADS)

Choi, J. H.; Kim, S. W.; Won, J. S.

2017-12-01

The objective of this study is monitoring and evaluating the stability of buildings in Seoul, Korea. This study includes both algorithm development and application to a case study. The development focuses on improving the PSI approach for discriminating various geophysical phase components and separating them from the target displacement phase. A thermal expansion is one of the key components that make it difficult for precise displacement measurement. The core idea is to optimize the thermal expansion factor using air temperature data and to model the corresponding phase by fitting the residual phase. We used TerraSAR-X SAR data acquired over two years from 2011 to 2013 in Seoul, Korea. The temperature fluctuation according to seasons is considerably high in Seoul, Korea. Other problem is the highly-developed skyscrapers in Seoul, which seriously contribute to DEM errors. To avoid a high computational burden and unstable solution of the nonlinear equation due to unknown parameters (a thermal expansion parameter as well as two conventional parameters: linear velocity and DEM errors), we separate a phase model into two main steps as follows. First, multi-baseline pairs with very short time interval in which deformation components and thermal expansion can be negligible were used to estimate DEM errors first. Second, single-baseline pairs were used to estimate two remaining parameters, linear deformation rate and thermal expansion. The thermal expansion of buildings closely correlate with the seasonal temperature fluctuation. Figure 1 shows deformation patterns of two selected buildings in Seoul. In the figures of left column (Figure 1), it is difficult to observe the true ground subsidence due to a large cyclic pattern caused by thermal dilation of the buildings. The thermal dilation often mis-leads the results into wrong conclusions. After the correction by the proposed method, true ground subsidence was able to be precisely measured as in the bottom right figure in Figure 1. The results demonstrate how the thermal expansion phase blinds the time-series measurement of ground motion and how well the proposed approach able to remove the noise phases caused by thermal expansion and DEM errors. Some of the detected displacements matched well with the pre-reported events, such as ground subsidence and sinkhole.

Numerical simulation of the fluid-structure interaction between air blast waves and soil structure

NASA Astrophysics Data System (ADS)

Umar, S.; Risby, M. S.; Albert, A. Luthfi; Norazman, M.; Ariffin, I.; Alias, Y. Muhamad

2014-03-01

Normally, an explosion threat on free field especially from high explosives is very dangerous due to the ground shocks generated that have high impulsive load. Nowadays, explosion threats do not only occur in the battlefield, but also in industries and urban areas. In industries such as oil and gas, explosion threats may occur on logistic transportation, maintenance, production, and distribution pipeline that are located underground to supply crude oil. Therefore, the appropriate blast resistances are a priority requirement that can be obtained through an assessment on the structural response, material strength and impact pattern of material due to ground shock. A highly impulsive load from ground shocks is a dynamic load due to its loading time which is faster than ground response time. Of late, almost all blast studies consider and analyze the ground shock in the fluid-structure interaction (FSI) because of its influence on the propagation and interaction of ground shock. Furthermore, analysis in the FSI integrates action of ground shock and reaction of ground on calculations of velocity, pressure and force. Therefore, this integration of the FSI has the capability to deliver the ground shock analysis on simulation to be closer to experimental investigation results. In this study, the FSI was implemented on AUTODYN computer code by using Euler-Godunov and the arbitrary Lagrangian-Eulerian (ALE). Euler-Godunov has the capability to deliver a structural computation on a 3D analysis, while ALE delivers an arbitrary calculation that is appropriate for a FSI analysis. In addition, ALE scheme delivers fine approach on little deformation analysis with an arbitrary motion, while the Euler-Godunov scheme delivers fine approach on a large deformation analysis. An integrated scheme based on Euler-Godunov and the arbitrary Lagrangian-Eulerian allows us to analyze the blast propagation waves and structural interaction simultaneously.

Monitoring on Xi'an ground fissures deformation with TerraSAR-X data

USGS Publications Warehouse

Zhao, C.; Zhang, Q.; Zhu, W.; Lu, Z.

2012-01-01

Owing to the fine resolution of TerraSAR-X data provided since 2007, this paper applied 6 TerraSAR data (strip mode) during 3rd Dec. 2009 to 23rd Mar. 2010 to detect and monitor the active fissures over Xi'an region. Three themes have been designed for high precision detection and monitoring of Xi'an-Chang'an fissures, as small baseline subsets (SBAS) to test the atmospheric effects of differential interferograms pair stepwise, 2-pass differential interferogram with very short baseline perpendicular to generate the whole deformation map with 44 days interval, and finally, corner reflector (CR) technique was used to closely monitor the relative deformation time series between two CRs settled crossing two ground fissures. Results showed that TerraSAR data are a good choice for small-scale ground fissures detection and monitoring, while special considerations should be taken for their great temporal and baseline decorrelation. Secondly, ground fissures in Xi'an were mostly detected at the joint section of stable and deformable regions. Lastly, CR-InSAR had potential ability to monitor relative deformation crossing fissures with millimeter precision.

Stress-dependent permeability and ground displacement during CO2 storage operation at KB-502 injection well, In Salah, Algeria

NASA Astrophysics Data System (ADS)

Rinaldi, A.; Rutqvist, J.

2012-12-01

The In Salah CO2 storage project (a joint venture among Statoil, BP, and Sonatrach) is one of the most important sites for understanding the geomechanics associated with carbon dioxide injection. InSAR data evaluated for the first years of injection show a ground-surface uplift of 5 to 10 mm per year at each of the injection wells. A double-lobe uplift pattern has been observed at KB-502, and both semi-analytical inverse deformation analysis (Vasco et al., 2010) and coupled numerical modeling of fluid flow and geomechanics (Rutqvist et al., 2011) have shown that this pattern of displacement can be explained by injection-induced deformation in a deep vertical fracture zone of fault, whose presence has been confirmed by recent 3D seismic survey (Gibson-Poole et al., 2010). Recently, Rinaldi and Rutqvist (2012) refined the previous modeling results, through the use of TOUGH-FLAC (Rutqvist et al., 2002), in order to more conclusively constrain the height of the fracture zone. Results were well in agreement with all available field observations, including all time evolutions and the shape of surface deformation, time-evolution of injection pressure, and the 3D seismic indications of the CO2 saturated fracture zone extending thousands of meters laterally. However, the analysis included a number of simplifications and uncertainties, such as time-step changes in aquifer permeability and the use of an elastic model, which preclude a good match with field data after shut in. Here we implement a new stress-dependent permeability function, to consider a more realistic changes in reservoir and fracture zone permeability, and to improve the match between field observations and modeling results, considering both the bottomhole pressure and the ground surface displacement. Furthermore, here we extent the length of the simulation to include modeling of the re-injection occurred in late 2010 for few months. A second major simplification by Rinaldi and Rutqvist (2012) is the assumption of fracture zone that could have opened instantaneously. Here we present also some early, simple study on potential fracture propagations coupled with stress-dependent permeability changes.

Spatial and temporal patterns of deformation at the Tendaho geothermal prospect, Ethiopia

NASA Astrophysics Data System (ADS)

Temtime, Tesfaye; Biggs, Juliet; Lewi, Elias; Hamling, Ian; Wright, Tim; Ayele, Atalay

2018-05-01

Observations of ground deformation in East Africa have been fundamental for unveiling the tectonics of continental rifting, assessing the seismic and volcanic hazard to development, and identifying geothermal resources. Here we investigate the active natural and anthropogenic processes in the Tendaho Graben, Afar using Interferometric Synthetic Aperture Radar (InSAR) collected by the Envisat satellite in 2004-2010. We used the Poly-Interferometric Rate And time series Estimation (π-RATE) method to calculate displacement in satellite line-of-sight, and a least-square inversion to decompose the line-of-sight displacement into vertical and rift perpendicular components. We observe two zones of deformation: a 20 km wide circular region of subsidence located 10 km northeast of the town of Semera with a maximum displacement rate of ∼5 cm/yr; and elongated zone (50 km) of subsidence in the area of the geothermal prospect, maximum rate of ∼4 cm/yr. The temporal characteristics of subsidence varies between these zones, with an increase in subsidence rate observed in the circular region in August 2008. We used a Bayesian inversion to find the best fitting source models and compared this to locations of seismicity and other geophysical observations. The pattern of deformation is consistent with a combination of magmatic and geothermal processes, but there does not appear to be a direct link to a sequence of dyke intrusions during 2005-2010 at Manda Hararo graben ∼60 km away, but dynamic stress changes or deep crustal flow could account for the observations.

Deformation from the 1989 Loma Prieta earthquake near the southwest margin of the Santa Clara Valley, California

USGS Publications Warehouse

Schmidt, Kevin M.; Ellen, Stephen D.; Peterson, David M.

2014-01-01

To gain additional measurement of any permanent ground deformation that accompanied this damage, we compiled and conducted post-earthquake surveys along two 5-km lines of horizontal control and a 15-km level line. Measurements of horizontal distortion indicate approximately 0.1 m shortening in a NE-SW direction across the valley margin, similar to the amount measured in the channel lining. Evaluation of precise leveling by the National Geodetic Survey showed a downwarp, with an amplitude of >0.1 m over a span of >12 km, that resembled regional geodetic models of coseismic deformation. Although the leveling indicates broad, regional warping, abrupt discontinuities characteristic of faulting characterize both the broad-scale distribution of damage and the local deformation of the channel lining. Reverse movement largely along preexisting faults and probably enhanced significantly by warping combined with enhanced ground shaking, produced the documented coseismic ground deformation.

Complex surface deformation monitoring and mechanism inversion over Qingxu-Jiaocheng, China with multi-sensor SAR images

NASA Astrophysics Data System (ADS)

Liu, Yuanyuan; Zhao, Chaoying; Zhang, Qin; Yang, Chengsheng

2018-02-01

Qingxu-Jiaocheng, China has been suffering severe land subsidence along with the development of ground fissure, which are controlled by local fault and triggered by groundwater withdrawal. With multi-sensor SAR images, we study the spatiotemporal evolution of ground deformation over Qingxu-Jiaocheng with an IPTA InSAR technique and assess the role of groundwater withdrawal to the observed deformation. Discrete GPS measurements are applied to verify the InSAR results. The RMSE of the differences between InSAR and GPS, i.e. ALOS and GPS and Envisat and GPS, are 5.7 mm and 6.3 mm in the LOS direction, respectively. The east-west and vertical components of the observed deformation from 2007 to 2010 are decomposed by using descending-track Envisat and ascending-track ALOS interferograms, indicating that the east-west component cannot be neglected when the deformation is large or the ground fissure is active. Four phases of land subsidence in the study region are successfully retrieved, and its spatiotemporal evolution is quantitatively analyzed. Lastly, a flat lying sill model with distributed contractions is implemented to model the InSAR deformation over Qingxu-Jiaocheng, which manifests that the ground deformation is mainly caused by groundwater withdrawal. This research provides new insights into the land subsidence monitoring and its mechanism inversion over Qingxu-Jiaocheng region.

Deformation at longyao ground fissure and its surroundings, north China plain, revealed by ALOS PALSAR PS-InSAR

NASA Astrophysics Data System (ADS)

Yang, Chengsheng; Lu, Zhong; Zhang, Qin; Zhao, Chaoying; Peng, Jianbing; Ji, Lingyun

2018-05-01

The Longyao ground fissure (LGF) is the longest and most active among more than 1000 ground fissures on the North China Plain. There have been many studies on the formation mechanism of the LGF, due to its scientific importance and its potential for damage to the environment. These studies have been based on both regional tectonic analysis and numerical simulations. In order to provide a better understanding of the formation mechanism, the deformation of the crack and its surrounding environment should be taken into consideration. In this paper, PS-InSAR technology was employed to assess the ground deformation of LGF and its surrounding area, using L-band ALOS-1 PALSAR images from 2007 to 2011. The characteristics of ground deformation, relationships between fissure activity and surrounding faults and groundwater exploitation were analyzed. This study shows that the north side of Longyao fault (LF) is uplifting while the south side is subsiding. This provides the tectonic conditions responsible for the activity of the ground fissure. Local groundwater exploitation also plays an important role in the development of ground fissures. InSAR observations were modeled to infer the loading depth (-2.8 km) and the slip rate (31.1 mm/yr) of LF.

Mechanics of Old Faithful Geyser, Calistoga, CA

USGS Publications Warehouse

Rudolph, M.L.; Manga, M.; Hurwitz, Shaul; Johnston, Malcolm J.; Karlstrom, L.; Wang, Chun-Yong

2012-01-01

In order to probe the subsurface dynamics associated with geyser eruptions, we measured ground deformation at Old Faithful Geyser of Calistoga, CA. We present a physical model in which recharge during the period preceding an eruption is driven by pressure differences relative to the aquifer supplying the geyser. The model predicts that pressure and ground deformation are characterized by an exponential function of time, consistent with our observations. The geyser's conduit is connected to a reservoir at a depth of at least 42 m, and pressure changes in the reservoir can produce the observed ground deformations through either a poroelastic or elastic mechanical model.

Mechanics of Old Faithful Geyser, Calistoga, California

NASA Astrophysics Data System (ADS)

Rudolph, M. L.; Manga, M.; Hurwitz, S.; Johnston, M.; Karlstrom, L.; Wang, C.-Y.

2012-12-01

In order to probe the subsurface dynamics associated with geyser eruptions, we measured ground deformation at Old Faithful Geyser of Calistoga, CA. We present a physical model in which recharge during the period preceding an eruption is driven by pressure differences relative to the aquifer supplying the geyser. The model predicts that pressure and ground deformation are characterized by an exponential function of time, consistent with our observations. The geyser's conduit is connected to a reservoir at a depth of at least 42 m, and pressure changes in the reservoir can produce the observed ground deformations through either a poroelastic or elastic mechanical model.

A preliminary study on surface ground deformation near shallow foundation induced by strike-slip faulting

NASA Astrophysics Data System (ADS)

Wong, Pei-Syuan; Lin, Ming-Lang

2016-04-01

According to investigation of recent earthquakes, ground deformation and surface rupture are used to map the influenced range of the active fault. The zones of horizontal and vertical surface displacements and different features of surface rupture are investigated in the field, for example, the Greendale Fault 2010, MW 7.1 Canterbury earthquake. The buildings near the fault rotated and displaced vertically and horizontally due to the ground deformation. Besides, the propagation of fault trace detoured them because of the higher rigidity. Consequently, it's necessary to explore the ground deformation and mechanism of the foundation induced by strike-slip faulting for the safety issue. Based on previous study from scaled analogue model of strike-slip faulting, the ground deformation is controlled by material properties, depth of soil, and boundary condition. On the condition controlled, the model shows the features of ground deformation in the field. This study presents results from shear box experiment on small-scale soft clay models subjected to strike-slip faulting and placed shallow foundations on it in a 1-g environment. The quantifiable data including sequence of surface rupture, topography and the position of foundation are recorded with increasing faulting. From the result of the experiment, first en echelon R shears appeared. The R shears rotated to a more parallel angle to the trace and cracks pulled apart along them with increasing displacements. Then the P shears crossed the basement fault in the opposite direction appears and linked R shears. Lastly the central shear was Y shears. On the other hand, the development of wider zones of rupture, higher rising surface and larger the crack area on surface developed, with deeper depth of soil. With the depth of 1 cm and half-box displacement 1.2 cm, en echelon R shears appeared and the surface above the fault trace elevated to 1.15 mm (Dv), causing a 1.16 cm-wide zone of ground-surface rupture and deformation (W). Compared to the investigation in field, rupture of the Greendale Fault, produced a 30-km-long, 300-m-wide zone of ground-surface rupture and deformation (W), involving 5.29 m maximum horizontal , 1.45 m maximum vertical (Dv, max) and 2.59 m average net displacement. Meanwhile, en echelon R shears and cracks were recorded in some region. Besides, the 400-m depth of deep sedimentation (Ds) in the Christchurch City area. Greendale Fault showed close ratio Dv/Ds and W/Ds compared to the experimental case (in the same order), which indicated the wide zone of ground-surface rupture and deformation may be normalized with the vertical displacement (Dv). The foundation located above the basement-fault trace had obvious horizontal displacements and counter-clockwise rotation with increasing displacement. Horizontal displacements and rotation decreased with deeper depth of soil. The deeper embedded foundation caused more rotation. Besides, the soil near the foundation is confined and pressed when it rotates. Key words: strike-slip fault, shallow foundation, ground deformation

Toward resolving an earthquake ground motion mystery in west Seattle, Washington State: Shallow seismic focusing may cause anomalous chimney damage

USGS Publications Warehouse

Stephenson, W.J.; Frankel, A.D.; Odum, J.K.; Williams, R.A.; Pratt, T.L.

2006-01-01

A shallow bedrock fold imaged by a 1.3-km long high-resolution shear-wave seismic reflection profile in west Seattle focuses seismic waves arriving from the south. This focusing may cause a pocket of amplified ground shaking and the anomalous chimney damage observed in earthquakes of 1949, 1965 and 2001. The 200-m bedrock fold at ???300-m depth is caused by deformation across an inferred fault within the Seattle fault zone. Ground motion simulations, using the imaged geologic structure and northward-propagating north-dipping plane wave sources, predict a peak horizontal acceleration pattern that matches that observed in strong motion records of the 2001 Nisqually event. Additionally, a pocket of chimney damage reported for both the 1965 and the 2001 earthquakes generally coincides with a zone of simulated amplification caused by focusing. This study further demonstrates the significant impact shallow (<1km) crustal structures can have on earthquake ground-motion variability.

InSAR observation of seasonal ground surface deformation in permafrost area near Batagay, Siberia

NASA Astrophysics Data System (ADS)

Yanagiya, K.; Furuya, M.

2017-12-01

Thawing of permafrost can lead to ground deformation. Ground deformation has been studied as a serious problem in the Arctic Ocean coastal area such as Russia for a long time, because the deformation causes damage to architectures at these areas. However, there have been no quantitative observation data, and the spatial and temporal distributions have hardly been investigated. On the other hand, by the recently global warming influence, the importance of organic carbon stored in permafrost is pointed out. Although the release of methane gas is confirmed in some thermokarst lakes, it is very difficult to observe the permafrost in a wide area by field study. Instead, it is technically possible to monitor the subsidence and uplift of the ground over the permafrost area, which could potentially make a significant contribution to the monitoring thawing process of permafrost. In this study, we attempted to detect ground deformation signal in permafrost area by remote sensing using interferometric synthetic aperture radar (InSAR). Using the data of two SAR satellites ALOS and ALOS2 launched by JAXA, we observed recent ground deformation from 2007 to 2016. Particularly recent observations of ALOS2 from 2014 to 2016 discovered distant displacements towards the LOS direction in the northeast region from the town of Batagay,Siberia. The diameter of the displacements area covers about 7.7 km. In this study, we considered that this signal is likely to be due to permafrost thawing, we also investigated the seasonal characteristics and looked back ALOS data of this area. In addition, since the high latitude area, observation results include noise due to the ionosphere, so we tried to remove the noise.

Long Term, Operational Monitoring Of Enhanced Oil Recovery In Harsh Environments With INSAR

NASA Astrophysics Data System (ADS)

Sato, S.; Henschel, M. D.

2012-01-01

Since 2004, MDA GSI has provided ground deformation measurements for an oil field in northern Alberta, Canada using InSAR technology. During this period, the monitoring has reliably shown the slow rise of the oil field due to enhanced oil recovery operations. The InSAR monitoring solution is essentially based on the observation of point and point-like targets in the field. Ground conditions in the area are almost continuously changing (in their reflectivity characteristics) making it difficult to ob- serve coherent patterns from the ground. The extended duration of the oil operations has allowed us to continue InSAR monitoring and transition from RADARSAT-1 to RADARSAT-2. With RADARSAT-2 and the enhancement of the satellite resolution capability has provided more targets of opportunity as identified by a differential coherence method. This poster provides an overview of the long term monitoring of the oil field in northern Alberta, Canada.

Identification of mine collapses, explosions and earthquakes using INSAR: a preliminary investigation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Foxall, B; Sweeney, J J; Walter, W R

1998-07-07

Interferograms constmcted from satellite-borne synthetic aperture radar images have the capability of mapping sub-cm ground surface deformation over areas on the order of 100 x 100 km with a spatial resolution on the order of 10 meters. We investigate the utility of synthetic aperture radar interferomehy (InSAR) used in conjunction with regional seismic methods in detecting and discriminating different types of seismic events in the context of special event analysis for the CTBT. For this initial study, we carried out elastic dislocation modeling of underground explosions, mine collapses and small (M<5.5) shallow earthquakes to produce synthetic interferograms and then analyzedmore » satellite radar data for a large mine collapse. The synthetic modeling shows that, for a given magnitude each type of event produces a distinctive pattern of ground deformation that can be recognized in, and recovered from, the corresponding interferogram. These diagnostic characteristics include not only differences in the polarities of surface displacements but also differences in displacement amplitudes from the different sources. The technique is especially sensitive to source depth, a parameter that is crucial in discriminating earthquakes from the other event types but is often very poorly constrained by regional seismic data alone. The ERS radar data analyzed is from a M L 5.2 seismic event that occurred in southwestern Wyoming on February 3,1995. Although seismic data from the event have some characteristics of an underground explosion, based on seismological and geodetic data it has been identified as being caused by a large underground collapse in the Solvay Mine. Several pairs of before-collapse and after-collapse radar images were phase processed to obtain interferograms. The minimum time separation for a before-collapse and after-collapse pair was 548 days. Even with this long time separation, phase coherence between the image pairs was acceptable and a deformation map was successfully obtained. Two images, separated by 1 day and occurring after the mine collapse, were used to form a digital elevation map (DEM) that was used to correct for topography. The interferograms identify the large deformation at the Solvay Mine as well as some areas of lesser deformation near other mines in the area. The large amount of deformation at the Solvay Mine was identified, but (as predicted by our dislocation modeling) could not be quantified absolutely because of the incoherent interference pattern it produced« less

Geotechnical aspects of the January 2003 Tecoma'n, Mexico, earthquake

USGS Publications Warehouse

Wartman, Joseph; Rodriguez-Marek, Adrian; Macari, Emir J.; Deaton, Scott; Ramirez-Reynaga, Marti'n; Ochoa, Carlos N.; Callan, Sean; Keefer, David; Repetto, Pedro; Ovando-Shelley, Efrai'n

2005-01-01

Ground failure was the most prominent geotechnical engineering feature of the 21 January 2003 Mw 7.6 Tecoma´n earthquake. Ground failure impacted structures, industrial facilities, roads, water supply canals, and other critical infrastructure in the state of Colima and in parts of the neighboring states of Jalisco and Michoaca´n. Landslides and soil liquefaction were the most common type of ground failure, followed by seismic compression of unsaturated materials. Reinforced earth structures generally performed well during the earthquake, though some structures experienced permanent lateral deformations up to 10 cm. Different ground improvement techniques had been used to enhance the liquefaction resistance of several sites in the region, all of which performed well and exhibited no signs of damage or significant ground deformation. Earth dams in the region experienced some degree of permanent deformation but remained fully functional after the earthquake.

Seperating Long-term Hydrological Loading and Tectonic Deformation Observed with Multi-temporal SAR Interferometry and GPS in Qinghai-Tibetan Plateau

NASA Astrophysics Data System (ADS)

LI, G.; Lin, H.

2014-12-01

From 2000 till present, most endorheic lakes in Tibetan plateau experienced quick increasing. Several largest lakes, gathered several meters depth water during one decade. Such massive mass increasing will lead to elastic and visco-elastic deformation of the ground. Qinghai-Tibetan Plateau is one the most active tectonic places in the world; monitoring its ground deformation is essential, when loading effect is a nuisance item. Due to the sparse distribution of GPS sites and most are roving sites, it is hard to distinguish tectonic component from mass loading effect. In this research we took Selin Co Lake located at Nujiang-Bangoin suture zone and evaluated long time ground deformation at hundred kilometers scale by multi-temporal SAR interferometry and simulate the ground deformation by loading history evaluated by multi mission satellite altimetry and optical images observation. At Nujiang-Bangoin suture zone, where GPS presented the maximum ground subsidence in Qinghai-Tibetan Plateau of 3.6mm/a which was found at the shore of Selin Co Lake from 1999 to 2011, when it experienced water level increasing of 0.7m/a. A model of elastic plate lying over Newtonian viscous half-space matches well with the results of multi-temporal SAR interferometry and GPS observations. We concluded that near Selin Co Lake area, ground deformation is composed by both tectonic and hydrological loading part. As SAR image coverage is much smaller than tectonic scale, we contribute the deformation detected by InSAR to loading effect. After evaluating and removing the hydrological loading effect, we founds that Nujiang-Bangoin suture zone did not experience quick subsidence, but only limited to 0.5mm/a. Selin Co Lake's quick volume increasing caused 3mm/a subsidence rate to the nearest GPS site. The Second nearest site showed the 1.4mm/a subsidence totally, which were composed by 1.05mm/a hydrological loading effect and the rest was tectonic. We also found that Young's Modulus is the most essential parameter for loading effect simulation, and our simulation gave the similar Young's Modulus as the previous seismic tomographic INDEPTH III program did. Therefore with accurate seismic tomographic results and loading history detected by remote sensing could accurately simulate ground deformation caused by hydrological loading.

Mathematical model of rolling an elastic wheel over deformable support base

NASA Astrophysics Data System (ADS)

Volskaia, V. N.; Zhileykin, M. M.; Zakharov, A. Y.

2018-02-01

One of the main direction of economic growth in Russia remains to be a speedy development of north and northeast regions that are the constituents of the 60 percent of the country territory. The further development of these territories requires new methods and technologies for solving transport and technological problems when off-road transportation of cargoes and people is conducting. One of the fundamental methods of patency prediction is imitation modeling of wheeled vehicles movement in different operating conditions. Both deformable properties of tires and physical and mechanical properties of the ground: normal tire deflection and gauge depth; variation of contact patch area depending on the load and pressure of air in the tire; existence of hysteresis losses in the tire material which are influencing on the rolling resistance due to friction processes between tire and ground in the contact patch; existence of the tangential reaction from the ground by entire contact area influence on the tractive patency. Nowadays there are two main trends in theoretical research of interaction wheeled propulsion device with ground: analytical method involving mathematical description of explored process and finite element method based on computational modeling. Mathematical models of interaction tire with the ground are used both in processes of interaction individual wheeled propulsion device with ground and researches of mobile vehicle dynamical models operated in specific road and climate conditions. One of the most significant imperfection of these models is the description of interaction wheel with flat deformable support base whereas profile of real support base surface has essential height of unevenness which is commensurate with radius of the wheel. The description of processes taking place in the ground under influence of the wheeled propulsion device using the finite element method is relatively new but most applicable lately. The application of this method allows to provide the most accurate description of the interaction process of a wheeled propulsion devices and the ground, also this method allows to define tension in the ground, deformation of the ground and the tire and ground’s compression. However, the high laboriousness of computations is essential shortcoming of that method therefore it’s hard to use these models as part of the general motion model of multi-axis wheeled vehicles. The purpose of this research is the elaboration of mathematical model of elastic wheel rolling over deformable rough support base taking into account the contact patch deformation. The mathematical model of rectilinear rolling an elastic wheel over rough deformable support base, taking into account variation of contact patch area and variation in the direction of the radial and tangential reactions also load bearing capacity of the ground, is developed. The efficiency of developed mathematical model of rectilinear rolling an elastic wheel over rough deformable support base is proved by the simulation methods.

Canny edge-based deformable image registration

NASA Astrophysics Data System (ADS)

Kearney, Vasant; Huang, Yihui; Mao, Weihua; Yuan, Baohong; Tang, Liping

2017-02-01

This work focuses on developing a 2D Canny edge-based deformable image registration (Canny DIR) algorithm to register in vivo white light images taken at various time points. This method uses a sparse interpolation deformation algorithm to sparsely register regions of the image with strong edge information. A stability criterion is enforced which removes regions of edges that do not deform in a smooth uniform manner. Using a synthetic mouse surface ground truth model, the accuracy of the Canny DIR algorithm was evaluated under axial rotation in the presence of deformation. The accuracy was also tested using fluorescent dye injections, which were then used for gamma analysis to establish a second ground truth. The results indicate that the Canny DIR algorithm performs better than rigid registration, intensity corrected Demons, and distinctive features for all evaluation matrices and ground truth scenarios. In conclusion Canny DIR performs well in the presence of the unique lighting and shading variations associated with white-light-based image registration.

Patterns of Alloy Deformation by Pulsed Pressure

NASA Astrophysics Data System (ADS)

Chebotnyagin, L. M.; Potapov, V. V.; Lopatin, V. V.

2015-06-01

Patterns of alloy deformation for optimization of a welding regime are studied by the method of modeling and deformation profiles providing high deformation quality are determined. A model of stepwise kinetics of the alloy deformation by pulsed pressure from the expanding plasma channel inside of a deformable cylinder is suggested. The model is based on the analogy between the acoustic and electromagnetic wave processes in long lines. The shock wave pattern of alloy deformation in the presence of multiple reflections of pulsed pressure waves in the gap plasma channel - cylinder wall and the influence of unloading waves from free surfaces are confirmed.

Inferring field-scale properties of a fractured aquifer from ground surface deformation during a well test

NASA Astrophysics Data System (ADS)

Schuite, Jonathan; Longuevergne, Laurent; Bour, Olivier; Boudin, Frédérick; Durand, Stéphane; Lavenant, Nicolas

2015-12-01

Fractured aquifers which bear valuable water resources are often difficult to characterize with classical hydrogeological tools due to their intrinsic heterogeneities. Here we implement ground surface deformation tools (tiltmetry and optical leveling) to monitor groundwater pressure changes induced by a classical hydraulic test at the Ploemeur observatory. By jointly analyzing complementary time constraining data (tilt) and spatially constraining data (vertical displacement), our results strongly suggest that the use of these surface deformation observations allows for estimating storativity and structural properties (dip, root depth, and lateral extension) of a large hydraulically active fracture, in good agreement with previous studies. Hence, we demonstrate that ground surface deformation is a useful addition to traditional hydrogeological techniques and opens possibilities for characterizing important large-scale properties of fractured aquifers with short-term well tests as a controlled forcing.

Probabilistic reconstruction of GPS vertical ground motion and comparison with GIA models

NASA Astrophysics Data System (ADS)

Husson, Laurent; Bodin, Thomas; Choblet, Gael; Kreemer, Corné

2017-04-01

The vertical position time-series of GPS stations have become long enough for many parts of the world to infer modern rates of vertical ground motion. We use the worldwide compilation of GPS trend velocities of the Nevada Geodetic Laboratory. Those rates are inferred by applying the MIDAS algorithm (Blewitt et al., 2016) to time-series obtained from publicly available data from permanent stations. Because MIDAS filters out seasonality and discontinuities, regardless of their causes, it gives robust long-term rates of vertical ground motion (except where there is significant postseismic deformation). As the stations are unevenly distributed, and because data errors are also highly variable, sometimes to an unknown degree, we use a Bayesian inference method to reconstruct 2D maps of vertical ground motion. Our models are based on a Voronoi tessellation and self-adapt to the spatially variable level of information provided by the data. Instead of providing a unique interpolated surface, each point of the reconstructed surface is defined through a probability density function. We apply our method to a series of vast regions covering entire continents. Not surprisingly, the reconstructed surface at a long wavelength is dominated by the GIA. This result can be exploited to evaluate whether forward models of GIA reproduce geodetic rates within the uncertainties derived from our interpolation, not only at high latitudes where postglacial rebound is fast, but also in more temperate latitudes where, for instance, such rates may compete with modern sea level rise. At shorter wavelengths, the reconstructed surface of vertical ground motion features a variety of identifiable patterns, whose geometries and rates can be mapped. Examples are transient dynamic topography over the convecting mantle, actively deforming domains (mountain belts and active margins), volcanic areas, or anthropogenic contributions.

Nuclear ground-state masses and deformations: FRDM(2012)

DOE PAGES

Moller, P.; Sierk, A. J.; Ichikawa, T.; ...

2016-03-25

Here, we tabulate the atomic mass excesses and binding energies, ground-state shell-plus-pairing corrections, ground-state microscopic corrections, and nuclear ground-state deformations of 9318 nuclei ranging from 16O to A=339. The calculations are based on the finite-range droplet macroscopic and the folded-Yukawa single-particle microscopic nuclear-structure models, which are completely specified. Relative to our FRDM(1992) mass table in Möller et al. (1995), the results are obtained in the same model, but with considerably improved treatment of deformation and fewer of the approximations that were necessary earlier, due to limitations in computer power. The more accurate execution of the model and the more extensivemore » and more accurate experimental mass data base now available allow us to determine one additional macroscopic-model parameter, the density-symmetry coefficient LL, which was not varied in the previous calculation, but set to zero. Because we now realize that the FRDM is inaccurate for some highly deformed shapes occurring in fission, because some effects are derived in terms of perturbations around a sphere, we only adjust its macroscopic parameters to ground-state masses.« less

Ground surface deformation patterns, magma supply, and magma storage at Okmok volcano, Alaska, from InSAR analysis: 1. Intereruption deformation, 1997–2008

USGS Publications Warehouse

Lu, Zhong; Dzurisin, Daniel; Biggs, Juliet; Wicks, Charles; McNutt, Steve

2010-01-01

Starting soon after the 1997 eruption at Okmok volcano and continuing until the start of the 2008 eruption, magma accumulated in a storage zone centered ~3.5 km beneath the caldera floor at a rate that varied with time. A Mogi-type point pressure source or finite sphere with a radius of 1 km provides an adequate fit to the deformation field portrayed in time-sequential interferometric synthetic aperture radar images. From the end of the 1997 eruption through summer 2004, magma storage increased by 3.2–4.5 × 107 m3, which corresponds to 75–85% of the magma volume erupted in 1997. Thereafter, the average magma supply rate decreased such that by 10 July 2008, 2 days before the start of the 2008 eruption, magma storage had increased by 3.7–5.2 × 107 m3 or 85–100% of the 1997 eruption volume. We propose that the supply rate decreased in response to the diminishing pressure gradient between the shallow storage zone and a deeper magma source region. Eventually the effects of continuing magma supply and vesiculation of stored magma caused a critical pressure threshold to be exceeded, triggering the 2008 eruption. A similar pattern of initially rapid inflation followed by oscillatory but generally slowing inflation was observed prior to the 1997 eruption. In both cases, withdrawal of magma during the eruptions depressurized the shallow storage zone, causing significant volcano-wide subsidence and initiating a new intereruption deformation cycle.

Cooperative deformations of periodically patterned hydrogels.

PubMed

Wang, Zhi Jian; Zhu, Chao Nan; Hong, Wei; Wu, Zi Liang; Zheng, Qiang

2017-09-01

Nature has shown elegant paradigms of smart deformation, which inspired biomimetic systems with controllable bending, folding, and twisting that are significant for the development of soft electronics and actuators. Complex deformations are usually realized by additively incorporating typical structures in selective domains with little interaction. We demonstrate the cooperative deformations of periodically patterned hydrogel sheets, in which neighboring domains mutually interact and cooperatively deform. Nonswelling disc gels are periodically positioned in a high-swelling gel. During the swelling process, the compartmentalized high-swelling gel alternately bends upward or downward to relieve the in-plane compression, but the overall integrated structure remains flat. The synergy between the elastic mismatch and the geometric periodicity selects the outcome pattern. Both experiment and modeling show that various types of cooperative deformation can be achieved by tuning the pattern geometry and gel properties. Different responsive polymers can also be patterned in one composite gel. Under stimulation, reversible transformations between different cooperative deformations are realized. The principle of cooperative deformation should be applicable to other materials, and the patterns can be miniaturized to the micrometer- or nanometer-scale level, providing the morphing materials with advanced functionalities for applications in various fields.

Regional variations in the stability and diffusion of water-ice in the Martian regolith

NASA Technical Reports Server (NTRS)

Mellon, Michael T.; Jakosky, Bruce M.

1992-01-01

Geologic evidence suggests subsurface water-ice has played an important role in the formation of Martian landforms. Forms of mass-wasting such as debris aprons and flow patterns on valley floors suggest creep deformation of ice-laden soil, while thermokarst and chaotic terrain suggest once extensive deposits of ground ice that were later removed. The global distribution of ice-related morphology was mapped. The mapping showed regional variation, in both latitude and longitude, in the distribution of debris aprons, concentric fill craters, and 'softened' crater profiles.

Exotic Structure of Carbon Isotopes

NASA Astrophysics Data System (ADS)

Suzuki, Toshio; Sagawa, Hiroyuki; Hagino, Kouichi

2003-12-01

Ground state properties of C isotopes, deformation and elecromagnetic moments, as well as electric dipole transition strength are investigated. We first study the ground state properties of C isotopes using a deformed Hartree-Fock (HF) + BCS model with Skyrme interactions. Isotope dependence of the deformation properties is investigated. Shallow deformation minima are found in several neutron-rich C isotopes. It is also shown that the deformation minima appear in both the oblate and the prolate sides in 17C and 19C having almost the same binding energies. Next, we carry out shell model calculations to study electromagnetic moments and electric dipole transitions of C isotopes. We point out the clear configuration dependence of the quadrupole and magnetic moments in the odd C isotopes, which will be useful to find out the deformation and spin-parities of the ground states of these nuclei. Electric dipole states of C isotopes are studied focusing on the interplay between low energy Pigmy strength and giant dipole resonances. Low peak energies, two-peak structure and large widths of the giant resonances show deformation effects. Calculated transition strength below dipole giant resonance in heavier C isotopes than 15C is found to exhaust 12 ~ 15% of the Thomas-Reiche-Kuhn sum rule value and 50 ~ 80% of the cluster sum rule value.

Land Deformation at the Thessaloniki - Giannitsa Plain (Greece) Deduced from 20- years Radar Observations using Persistent Scatterers Techniques

NASA Astrophysics Data System (ADS)

Svigkas, N.; Papoutsis, I.; Loupasakis, K.; Kiratzi, A. A.; Kontoes, C.

2015-12-01

We present the detected deformation and interpret the results in the light of ground-truth hydrological data, for the Thessaloniki-Giannitsa plain, the largest deltaic plain in Greece, encircled by Mounts Vermio, Paiko and Pieria. The contemporary morphology was gradually developed from the tectonic variations of the upper Pleistocene. The area has been subjected to many changes due to both natural causes and to human intervention. ERS-1, 2 and Envisat data provided from the European Space Agency were analysed to produce a time-series analysis based on Persistent Scatterer techniques. The mass processing of the 81 satellite images led to the creation of more than 250 Interferograms. The broader area of interest consists primarily of agricultural lands, leading to limited Interferometric coherence, and therefore careful Interferogram filtering and phase unwrapping of the input stack was crucial for reliable velocity generation. Our results show a strong deformation signal in regions of significant lifelines, as the railway and road network. Moreover, the satellite imagery revealed two significantly deforming sites: Kalochori and Sindos. The broader Kalochori region, the locus of the industrial activity of the city of Thessaloniki, is located below sea level. Both sites are suffering from land subsidence for more than 50 years, with several marine invasions reported in the past. Interestingly enough the two datasets -that represent two decades- show a reversed deformation pattern: The period in-between 1993 to 2000 is characterized by subsidence up to 34 mm/y, whereas from 2002 to 2010 there is an uplifting trend (more than 20 mm/yr). This result is crosschecked with hydrogeological data; the interpretation depicts that at Kalochori and Sindos the human factor (i.e. over pumping) is the dominant driver of these surface displacements. Although this was an assumption of previous studies, here we present for the first time, systematic proof that the detected uplift of the second decade acts as a rebound of the ground-water level.

Characterization of intrabasin faulting and deformation for earthquake hazards in southern Utah Valley, Utah, from high-resolution seismic imaging

USGS Publications Warehouse

Stephenson, William J.; Odum, Jack K.; Williams, Robert A.; McBride, John H.; Tomlinson, Iris

2012-01-01

We conducted active and passive seismic imaging investigations along a 5.6-km-long, east–west transect ending at the mapped trace of the Wasatch fault in southern Utah Valley. Using two-dimensional (2D) P-wave seismic reflection data, we imaged basin deformation and faulting to a depth of 1.4 km and developed a detailed interval velocity model for prestack depth migration and 2D ground-motion simulations. Passive-source microtremor data acquired at two sites along the seismic reflection transect resolve S-wave velocities of approximately 200 m/s at the surface to about 900 m/s at 160 m depth and confirm a substantial thickening of low-velocity material westward into the valley. From the P-wave reflection profile, we interpret shallow (100–600 m) bedrock deformation extending from the surface trace of the Wasatch fault to roughly 1.5 km west into the valley. The bedrock deformation is caused by multiple interpreted fault splays displacing fault blocks downward to the west of the range front. Further west in the valley, the P-wave data reveal subhorizontal horizons from approximately 90 to 900 m depth that vary in thickness and whose dip increases with depth eastward toward the Wasatch fault. Another inferred fault about 4 km west of the mapped Wasatch fault displaces horizons within the valley to as shallow as 100 m depth. The overall deformational pattern imaged in our data is consistent with the Wasatch fault migrating eastward through time and with the abandonment of earlier synextensional faults, as part of the evolution of an inferred 20-km-wide half-graben structure within Utah Valley. Finite-difference 2D modeling suggests the imaged subsurface basin geometry can cause fourfold variation in peak ground velocity over distances of 300 m.

Monitoring of the Ground Fissure Activity Within Yuncheng Basin by Time Series Insar

NASA Astrophysics Data System (ADS)

Zhang, F.; Yang, C. S.; Zhao, C. Y.; Liu, R. C.

2018-04-01

Yuncheng area is one of the most extensive distributions of ground fissures in Shanxi basin, especially in Yanhu District of Yuncheng, the disaster of ground fissures and ground subsidence are the most serious. According to previous studies, the development and distribution of the ground fissures in this area are mainly controlled by the underlying active faults. In order to provide a better understanding of the formation mechanism, the deformation of ground fissures and its surrounding environment should be taken into consideration. In this paper, PS-InSAR technology was employed to assess the time-series ground deformation of Yuncheng ground fissures and its surrounding area with X-band TerraSAR images from 2013 to 2015. The interaction between ground fissures activity and land subsidence, groundwater, precipitation and surrounding faults will be discussed.

10 CFR 72.103 - Geological and seismological characteristics for applications for dry cask modes of storage on or...

Code of Federal Regulations, 2010 CFR

2010-01-01

..., and that are not in areas of known seismic activity, a standardized design earthquake ground motion... motion, tectonic surface deformation, nontectonic deformation, earthquake recurrence rates, fault... of the Design Earthquake Ground Motion (DE). The DE for the site is characterized by both horizontal...

10 CFR 72.103 - Geological and seismological characteristics for applications for dry cask modes of storage on or...

Code of Federal Regulations, 2011 CFR

2011-01-01

..., and that are not in areas of known seismic activity, a standardized design earthquake ground motion... motion, tectonic surface deformation, nontectonic deformation, earthquake recurrence rates, fault... of the Design Earthquake Ground Motion (DE). The DE for the site is characterized by both horizontal...

10 CFR 72.103 - Geological and seismological characteristics for applications for dry cask modes of storage on or...

Code of Federal Regulations, 2013 CFR

2013-01-01

..., and that are not in areas of known seismic activity, a standardized design earthquake ground motion... motion, tectonic surface deformation, nontectonic deformation, earthquake recurrence rates, fault... of the Design Earthquake Ground Motion (DE). The DE for the site is characterized by both horizontal...

10 CFR 72.103 - Geological and seismological characteristics for applications for dry cask modes of storage on or...

Code of Federal Regulations, 2014 CFR

2014-01-01

..., and that are not in areas of known seismic activity, a standardized design earthquake ground motion... motion, tectonic surface deformation, nontectonic deformation, earthquake recurrence rates, fault... of the Design Earthquake Ground Motion (DE). The DE for the site is characterized by both horizontal...

10 CFR 72.103 - Geological and seismological characteristics for applications for dry cask modes of storage on or...

Code of Federal Regulations, 2012 CFR

2012-01-01

..., and that are not in areas of known seismic activity, a standardized design earthquake ground motion... motion, tectonic surface deformation, nontectonic deformation, earthquake recurrence rates, fault... of the Design Earthquake Ground Motion (DE). The DE for the site is characterized by both horizontal...

Convexities move because they contain matter.

PubMed

Barenholtz, Elan

2010-09-22

Figure-ground assignment to a contour is a fundamental stage in visual processing. The current paper introduces a novel, highly general dynamic cue to figure-ground assignment: "Convex Motion." Across six experiments, subjects showed a strong preference to assign figure and ground to a dynamically deforming contour such that the moving contour segment was convex rather than concave. Experiments 1 and 2 established the preference across two different kinds of deformational motion. Additional experiments determined that this preference was not due to fixation (Experiment 3) or attentional mechanisms (Experiment 4). Experiment 5 found a similar, but reduced bias for rigid-as opposed to deformational-motion, and Experiment 6 demonstrated that the phenomenon depends on the global motion of the effected contour. An explanation of this phenomenon is presented on the basis of typical natural deformational motion, which tends to involve convex contour projections that contain regions consisting of physical "matter," as opposed to concave contour indentations that contain empty space. These results highlight the fundamental relationship between figure and ground, perceived shape, and the inferred physical properties of an object.

Graphene ground states

NASA Astrophysics Data System (ADS)

Friedrich, Manuel; Stefanelli, Ulisse

2018-06-01

Graphene is locally two-dimensional but not flat. Nanoscale ripples appear in suspended samples and rolling up often occurs when boundaries are not fixed. We address this variety of graphene geometries by classifying all ground-state deformations of the hexagonal lattice with respect to configurational energies including two- and three-body terms. As a consequence, we prove that all ground-state deformations are either periodic in one direction, as in the case of ripples, or rolled up, as in the case of nanotubes.

The interaction of sound with a poroelastic ground

NASA Astrophysics Data System (ADS)

Hickey, C. J.

2012-12-01

An airborne acoustic wave impinging on the surface of the ground provides a good mechanical source for investigating the near surface. Since the ground is porous, the impinging sound wave induces motion of the fluid within the pores as well as vibrating the solid framework. The most complete understanding of the interaction of airborne sound with the ground is to treat the ground as a poroelastic or poroviscoelastic medium. This treatment predicts that three types of waves can propagate in a ground with a deformable framework: two compressional waves, the fast or Type I and slow or Type II wave and one shear wave. Model calculations of the energy partition and an air-soil interface predict that most of the energy is partitioned into the Type II compressional wave, less into the Type I compressional wave, and little energy is partitioned into the shear wave. However, when measuring the solid motion of the soil one must consider how much of that wave energy is in terms of solid velocity. The deformation associated with Type II compressional wave has only a small contribution from the solid component whereas the bulk deformation of the Type I compressional wave has a solid to fluid deformation ratio of approximately one. This modeling suggests that the soil solid velocity induced by an acoustic source is associated with the Type I compressional wave. In other words, the airborne source is simply an inefficient seismic source.

Correlation between land cover and ground vulnerability in Alexandria City (Egypt) using time series SAR interferometry and optical Earth observation data

NASA Astrophysics Data System (ADS)

Seleem, T.; Stergiopoulos, V.; Kourkouli, P.; Perrou, T.; Parcharidis, Is.

2017-10-01

The main scope of this study is to investigate the potential correlation between land cover and ground vulnerability over Alexandria city, Egypt. Two different datasets for generating ground deformation and land cover maps were used. Hence, two different approaches were followed, a PSI approach for surface displacement mapping and a supervised classification algorithm for land cover/use mapping. The interferometric results show a gradual qualitative and quantitative differentiation of ground deformation from East to West of Alexandria government. We selected three regions of interest, in order to compare the obtained interferometric results with the different land cover types. The ground deformation may be resulted due to different geomorphic and geologic factors encompassing the proximity to the active deltaic plain of the Nile River, the expansion of the urban network within arid regions of recent deposits, the urban density increase, and finally the combination of the above mentioned parameters.

In-situ monitoring of deformation of clayey and volcanic sequences in the lacustrine plain of Iztapalapa, Mexico City

NASA Astrophysics Data System (ADS)

Carreon-Freyre, D.; Cerca, M.; Barrientos, B.; Gutierrez, R.; Blancas, D.

2012-12-01

Major cities of Central Mexico with lowering of land elevation problems are located in inter-volcanic and fault bounded basins within the central Trans-Mexican Volcanic Belt (TMVB). The most representative and studied case of ground deformation is Mexico City, where the Iztapalapa Municipality presents the highest population density. This area is located over the geological contact between the "Sierra de Santa Catarina" volcanic range and a lacustrine plain. Filling of lacustrine basins includes silty and clayey sediments as well as pyroclastic deposits (coarse and fine grained) and volcanic rocks layers. We used Ground Penetrating Radar (GPR) and MASW prospection to evaluate contrasts in the physical properties of fine grained soils and identify geometry of the deformational features and implemented a mechanical system for in situ monitoring in fractured sites. Deformational features in this basin reflect an interplay between the geological history (depositional conditions), load history, seismic activity, and faulting. Plastic mechanical behaviour predominates in these clayey sediments and differential deformation locally triggers brittle fracturing and/or subsidence of the surface. In this work we present the results of monitoring and characterization of ground deformation and fracturing in different sequences, our results show a dynamic interplay between the mechanisms of ground fracturing and the stress history of sedimentary sequences. Relating the mechanical behaviour of the studied sequences with variations of physical and geological properties should be taken into account to estimate land level lowering and risk of fracturing for urban development planning.

Simplified dynamic analysis to evaluate liquefaction-induced lateral deformation of earth slopes: a computational fluid dynamics approach

NASA Astrophysics Data System (ADS)

Jafarian, Yaser; Ghorbani, Ali; Ahmadi, Omid

2014-09-01

Lateral deformation of liquefiable soil is a cause of much damage during earthquakes, reportedly more than other forms of liquefaction-induced ground failures. Researchers have presented studies in which the liquefied soil is considered as viscous fluid. In this manner, the liquefied soil behaves as non-Newtonian fluid, whose viscosity decreases as the shear strain rate increases. The current study incorporates computational fluid dynamics to propose a simplified dynamic analysis for the liquefaction-induced lateral deformation of earth slopes. The numerical procedure involves a quasi-linear elastic model for small to moderate strains and a Bingham fluid model for large strain states during liquefaction. An iterative procedure is considered to estimate the strain-compatible shear stiffness of soil. The post-liquefaction residual strength of soil is considered as the initial Bingham viscosity. Performance of the numerical procedure is examined by using the results of centrifuge model and shaking table tests together with some field observations of lateral ground deformation. The results demonstrate that the proposed procedure predicts the time history of lateral ground deformation with a reasonable degree of precision.

Spatiotemporal analysis and interpretation of 2003-2013 ground deformation at Campi Flegrei, Italy, observed by advanced DInSAR

NASA Astrophysics Data System (ADS)

Tiampo, Kristy; Samsonov, Sergey; González, Pablo; Fernández, Jose; Camacho, Antonio

2014-05-01

Studies identify Campi Flegrei caldera as one of the highest risk volcanic areas in the world because of its close proximity to the city of Naples, the third largest municipality in Italy with population close to 1 million inhabitants, making it one of the most dangerous volcanic areas on Earth (Orsi et al., 2004; De Natale et al., 2006; Isaia et al., 2009). The last major eruption occurred at Monte Nuovo in 1538, following a short term of ground uplift which interrupted a period of secular subsidence that continued after the eruption. Since that time, Campi Flegrei caldera has undergone frequent episodes of ground uplift and subsidence, with uplift phases accompanied by seismic activity (Troise et al., 2007). Well-established volcanic surveillance networks monitor changes in seismicity, gas emissions and active ground deformation occurring in volcanic areas as indicators of renewed volcanic/magmatic activities, potentially culminating in eruption. Since 1988, secular subsidence has continued at the historic rate of approximately 1.5 cm/yr. Surveys revealed significant gravity changes between 1981 and 2001, likely the result of dynamic changes in the subsurface magmatic reservoir (Dvorak & Berrino, 1991; Fernández et al., 2001; Gottsmann et al., 2003), changes within the subsurface hydrothermal systems (Bonafede & Mazzanti, 1998), or a combination (Gottsmann et al., 2005, 2006). In this study we apply the advanced Multidimensional SBAS (MSBAS) InSAR technique to measure ground deformation with high temporal and spatial resolution, and with high precision. We used 2003-2010 ENVISAT and 2009-2013 RADARSAT-2 satellite radar images and produced time series for the vertical and horizontal (east-west) components of deformation. Ground deformation results cover the entire Naples Bay area and, in particular, Campi Flegrei. Starting from June of 2010 we observe a moderate uplift at Campi Flegrei caldera. The rate of uplift substantially increased in 2011 and further accelerated in 2012. Between 2010 and 2013, the maximum cumulative uplift reached about 13 cm. Horizontal motions of up to 7 cm also were observed. We model the observed ground deformation in order to determine source parameters and the implication for volcanic hazard reduction in the Campi Flegrei region.

Surface deformation time-series analysis at Ischia Island (South Italy) carried out via multi-platform monitoring systems

NASA Astrophysics Data System (ADS)

Manzo, Mariarosaria; Del Gaudio, Carlo; De Martino, Prospero; Ricco, Ciro; Tammaro, Umberto; Castaldo, Raffaele; Tizzani, Pietro; Lanari, Riccardo

2014-05-01

Ischia Island, located at the North-Western corner of the Gulf of Napoli (South Italy), is a volcanic area, whose state of activity is testified from eruptions (the last one occurred in 1302), earthquakes (the most disastrous in 1881 and 1883), hydrothermal manifestations and ground deformation. In this work we present the state of the art of the Ischia Island ground deformation phenomena through the joint analysis of data collected via different monitoring methodologies (leveling, GPS, and Differential SAR Interferometry) during the last twenty years. In particular, our analysis benefits from the large amount of periodic and continuous geodetic measurements collected by the 257 leveling benchmarks and the 20 (17 campaign and 3 permanent) GPS stations deployed on the island. Moreover, it takes advantage from the large archives of C-band SAR data (about 300 ascending and descending ERS-1/2 and ENVISAT images) acquired over the island since 1992 and the development of the advanced Differential SAR Interferometry (DInSAR) technique referred to as Small BAseline Subset (SBAS). The latter, allows providing space-time information on the ground displacements measured along the radar line of sight (LOS), and thanks to the availability of multi-orbit SAR data, permits to discriminate the vertical and east-west components of the detected displacements. Our integrated analysis reveals a complex deformative scenario; in particular, it identifies a spatially extended subsidence pattern, which increases as we move to higher heights, with no evidence of any uplift phenomena. This broad effect involve the Northern, Eastern, Southern and South-Western sectors of the island where we measure velocity values not exceeding -6 mm/year; moreover, we identify a more localized phenomenon affecting the North-Western area in correspondence to the Fango zone, where velocity values up to -10 mm/year are retrieved. In addition, our study shows a migration of the Eastern sector of the island towards West with velocity values of -1/-2 mm/year. Conversely, a not clear behaviour of the central and South-Western areas is found; indeed, while the GPS velocity vectors are primarily Northward directed, the DInSAR measurements reveal a migration of these sectors towards East; in both cases we measure deformation velocity values of a very few mm/year. This discrepancy is very likely related to the fact that the North deformation component does not contribute to the measured LOS displacement component due to the nearly polar characteristics of the radar sensor orbits. The performed integrated time-series analysis can significantly contribute to the comprehension of the volcanic island dynamics, especially in the case of long-term observations that promote the investigation, modelling and interpretation of the physical processes behind the deformation phenomena at different temporal and spatial scales.

In-flight measurements of aircraft propeller deformation by means of an autarkic fast rotating imaging system

NASA Astrophysics Data System (ADS)

Stasicki, Boleslaw; Boden, Fritz

2015-03-01

The non-intrusive in-flight measurement of the deformation and pitch of the aircraft propeller is a demanding task. The idea of an imaging system integrated and rotating with the aircraft propeller has been presented on the 30th International Congress on High-Speed Imaging and Photonics (ICHSIP30) in 2012. Since then this system has been constructed and tested in the laboratory as well as on the real aircraft. In this paper we outline the principle of Image Pattern Correlation Technique (IPCT) based on Digital Image Correlation (DIC) and describe the construction of a dedicated autarkic 3D camera system placed on the investigated propeller and rotating at its full speed. Furthermore, the results of the first ground and in-flight tests are shown and discussed. This development has been found by the European Commission within the 7th frame project AIM2 (contract no. 266107).

Hydrothermal fluid flow models of Campi Flegrei caldera, Italy constrained by InSAR surface deformation time series observations

NASA Astrophysics Data System (ADS)

Lundgren, P.; Lanari, R.; Manzo, M.; Sansosti, E.; Tizzani, P.; Hutnak, M.; Hurwitz, S.

2008-12-01

Campi Flegrei caldera, Italy, located along the Bay of Naples, has a long history of significant vertical deformation, with the most recent large uplift (>1.5m) occurring in 1983-1984. Each episode of uplift has been followed by a period of subsidence that decreases in rate with time and may be punctuated by brief episodes of lesser uplift. The large amplitude of the major uplifts that occur without volcanic activity, and the subsequent subsidence has been argued as evidence for hydrothermal amplification of any magmatic source. The later subsidence and its temporal decay have been argued as due to diffusion of the pressurized caldera fill material into the less porous surrounding country rock. We present satellite synthetic aperture radar (SAR) interferometry (InSAR) time series analysis of ERS and Envisat data from the European Space Agency, based on exploiting the Small Baseline Subset (SBAS) approach [Berardino et al., 2002]; this allows us to generate maps of relative surface deformation though time, beginning in 1992 through 2007, that are relevant to both ascending and descending satellite orbits. The general temporal behavior is one of subsidence punctuated by several lesser uplift episodes. The spatial pattern of deformation can be modeled through simple inflation/deflation sources in an elastic halfspace. Given the evidence to suggest that fluids may play a significant role in the temporal deformation of Campi Flegrei, rather than a purely magmatic or magma chamber-based interpretation, we model the temporal and spatial evolution of surface deformation as a hydrothermal fluid flow process. We use the TOUGH2-BIOT2 set of numerical codes [Preuss et al., 1999; Hsieh, 1996], which couple multi-phase (liquid-gas) and multi-component (H2O-CO2) fluid flow in a porous or fractured media with plane strain deformation and fluid flow in a linearly elastic porous medium. We explore parameters related to the depth and temporal history of fluid injection, fluid composition, circulation geometries, and the physical properties of the media, to explain the InSAR time series. References: Berardino, P., R. Lanari, E. Sansosti (2002), A new Algorithm for surface deformation monitoring based on small baseline differential SAR interferograms, IEEE Transactions on Geoscience and Remote Sensing, 40, 11, 2375-2383. Pruess, L., C. Oldenburg, and G. Moridis (1999), TOUGH2 user's guide, version 2.0, Paper LBNL-43134, Lawrence Berkeley Natl. Lab., Berkeley, Calif. Hsieh, P. A. (1996), Deformation-induced changes in hydraulic head during ground-water withdrawal, Ground Water, 34, 1082-1089.

Octupole deformation in odd-odd nuclei

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheline, R.K.

1988-01-01

Comparison of the experimental and theoretical ground-state spins of odd-odd nuclei in the region 220less than or equal toAless than or equal to228 generally shows agreement with a folded Yukawa octupole deformed model with epsilon/sub 3/ = 0.08 and some lack of agreement with the same model with epsilon/sub 3/ = 0. Thus in spite of limited spectroscopic information, the ground-state spins suggest the existence of octupole deformation in odd-odd nuclei in the region 220less than or equal toAless than or equal to228.

Estimation of Surface Deformation due to Pasni Earthquake Using SAR Interferometry

NASA Astrophysics Data System (ADS)

Ali, M.; Shahzad, M. I.; Nazeer, M.; Kazmi, J. H.

2018-04-01

Earthquake cause ground deformation in sedimented surface areas like Pasni and that is a hazard. Such earthquake induced ground displacements can seriously damage building structures. On 7 February 2017, an earthquake with 6.3 magnitudes strike near to Pasni. We have successfully distinguished widely spread ground displacements for the Pasni earthquake by using InSAR-based analysis with Sentinel-1 satellite C-band data. The maps of surface displacement field resulting from the earthquake are generated. Sentinel-1 Wide Swath data acquired from 9 December 2016 to 28 February 2017 was used to generate displacement map. The interferogram revealed the area of deformation. The comparison map of interferometric vertical displacement in different time period was treated as an evidence of deformation caused by earthquake. Profile graphs of interferogram were created to estimate the vertical displacement range and trend. Pasni lies in strong earthquake magnitude effected area. The major surface deformation areas are divided into different zones based on significance of deformation. The average displacement in Pasni is estimated about 250 mm. Maximum pasni area is uplifted by earthquake and maximum uplifting occurs was about 1200 mm. Some of areas was subsidized like the areas near to shoreline and maximum subsidence was estimated about 1500 mm. Pasni is facing many problems due to increasing sea water intrusion under prevailing climatic change where land deformation due to a strong earthquake can augment its vulnerability.

Evaluation of ground deformations induced by the 1999 Kocaeli earthquake (Turkey) at selected sites on shorelines

NASA Astrophysics Data System (ADS)

Aydan, Ömer; Ulusay, Reşat; Atak, Veysel Okan

2008-03-01

The Kocaeli earthquake ( M w = 7.4) of 17 August 1999 occurred in the Eastern Marmara Region of Turkey along the North Anadolu Fault and resulted in a very serious loss of life and property. One of the most important geotechnical issues of this event was the permanent ground deformations because of both liquefaction and faulting. These deformations occurred particularly along the southern shores of İzmit Bay and Sapanca Lake between the cities of Yalova and Adapazarı in the west and east, respectively. In this study, three sites founded on delta fans, namely Değirmendere Nose, Yeniköy tea garden at Seymen on the coast of İzmit Bay, and Vakıf Hotel site on the coast of Sapanca Lake were selected as typical cases. The main causes of the ground deformations at these sites were then investigated. Geotechnical characterization of the ground, derivation of displacement vectors from the pre- and post-earthquake aerial photographs, liquefaction assessments based on field performance data, and analyses carried out using the sliding body method have been fundamental in this study. The displacement vectors determined from photogrammetric evaluations conducted at Değirmendere and Seymen showed a combined movement of faulting and liquefaction. But except the movements in the close vicinity of shorelines, the dominant factor in this movement was faulting. The results obtained from the analyses suggested that the ground failure at Değirmendere was a submarine landslide mainly because of earthquake shaking rather than liquefaction. On the other hand, the ground failures at the Yeniköy tea garden on the coast of Seymen and the hotel area in Sapanca town resulted from liquefaction-induced lateral spreading. It was also obtained that the ground deformations estimated from the sliding body method were quite close to those measured by aerial photogrammetry technique.

PSI Wide Area Product (WAP) for measuring Ground Surface Displacements at regional level for multi-hazards studies

NASA Astrophysics Data System (ADS)

Duro, Javier; Iglesias, Rubén; Blanco, Pablo; Albiol, David; Koudogbo, Fifamè

2015-04-01

The Wide Area Product (WAP) is a new interferometric product developed to provide measurement over large regions. Persistent Scatterers Interferometry (PSI) has largely proved their robust and precise performance in measuring ground surface deformation in different application domains. In this context, however, the accurate displacement estimation over large-scale areas (more than 10.000 km2) characterized by low magnitude motion gradients (3-5 mm/year), such as the ones induced by inter-seismic or Earth tidal effects, still remains an open issue. The main reason for that is the inclusion of low quality and more distant persistent scatterers in order to bridge low-quality areas, such as water bodies, crop areas and forested regions. This fact yields to spatial propagation errors on PSI integration process, poor estimation and compensation of the Atmospheric Phase Screen (APS) and the difficult to face residual long-wavelength phase patterns originated by orbit state vectors inaccuracies. Research work for generating a Wide Area Product of ground motion in preparation for the Sentinel-1 mission has been conducted in the last stages of Terrafirma as well as in other research programs. These developments propose technological updates for keeping the precision over large scale PSI analysis. Some of the updates are based on the use of external information, like meteorological models, and the employment of GNSS data for an improved calibration of large measurements. Usually, covering wide regions implies the processing over areas with a land use which is chiefly focused on livestock, horticulture, urbanization and forest. This represents an important challenge for providing continuous InSAR measurements and the application of advanced phase filtering strategies to enhance the coherence. The advanced PSI processing has been performed out over several areas, allowing a large scale analysis of tectonic patterns, and motion caused by multi-hazards as volcanic, landslide and flood. Several examples of the application of the PSI WAP to wide regions for measuring ground displacements related to different types of hazards, natural and human induced will be presented. The InSAR processing approach to measure accurate movements at local and large scales for allowing multi-hazard interpretation studies will also be discussed. The test areas will show deformations related to active faults systems, landslides in mountains slopes, ground compaction over underneath aquifers and movements in volcanic areas.

Using PS-InSAR to detect surface deformation in geothermal areas of West Java in Indonesia

NASA Astrophysics Data System (ADS)

Maghsoudi, Yasser; van der Meer, Freek; Hecker, Christoph; Perissin, Daniele; Saepuloh, Asep

2018-02-01

In this paper, the Persistent Scatterer InSAR (PS-InSAR) technique is applied in order to investigate the ground deformation in and around two geothermal areas in West Java, Indonesia. Two time-series of ALOS PALSAR and Sentinel-1A acquisitions, covering the period from 2007 to 2009 and 2015-2016, are analysed. The first case study examines the Wayang Windu geothermal zone where the PS-InSAR analysis provides an overview of the surface deformation around a geothermal reservoir. Uplift is observed around the injection wells in the area. The second example involves the use of the PS-InSAR technique over a more recent geothermal system in Patuha field. Again, a pattern of uplift was observed around the only available injection well in the area. Due to the dense vegetation coverage of the geothermal areas in West Java, the longer wavelength ALOS PALSAR data is provides better results by identifying a larger number of PS points. Additionally, experiments have been carried out to compare the resulting deformation with another example of the fluid migration process i.e. water extraction in Bandung basin. The potential of sentinel-1A and ALOS PALSR data are compared in all the experiments.

Dynamic deformations and the M6.7, Northridge, California earthquake

USGS Publications Warehouse

Gomberg, J.

1997-01-01

A method of estimating the complete time-varying dynamic formation field from commonly available three-component single station seismic data has been developed and applied to study the relationship between dynamic deformation and ground failures and structural damage using observations from the 1994 Northridge, California earthquake. Estimates from throughout the epicentral region indicate that the horizontal strains exceed the vertical ones by more than a factor of two. The largest strains (exceeding ???100 ??strain) correlate with regions of greatest ground failure. There is a poor correlation between structural damage and peak strain amplitudes. The smallest strains, ???35 ??strain, are estimated in regions of no damage or ground failure. Estimates in the two regions with most severe and well mapped permanent deformation, Potrero Canyon and the Granada-Mission Hills regions, exhibit the largest strains; peak horizontal strains estimates in these regions equal ???139 and ???229 ??strain respectively. Of note, the dynamic principal strain axes have strikes consistent with the permanent failure features suggesting that, while gravity, sub-surface materials, and hydrologic conditions undoubtedly played fundamental roles in determining where and what types of failures occurred, the dynamic deformation field may have been favorably sized and oriented to initiate failure processes. These results support other studies that conclude that the permanent deformation resulted from ground shaking, rather than from static strains associated with primary or secondary faulting. They also suggest that such an analysis, either using data or theoretical calculations, may enable observations of paleo-ground failure to be used as quantitative constraints on the size and geometry of previous earthquakes. ?? 1997 Elsevier Science Limited.

Soft tissue modelling with conical springs.

PubMed

Omar, Nadzeri; Zhong, Yongmin; Jazar, Reza N; Subic, Aleksandar; Smith, Julian; Shirinzadeh, Bijan

2015-01-01

This paper presents a new method for real-time modelling soft tissue deformation. It improves the traditional mass-spring model with conical springs to deal with nonlinear mechanical behaviours of soft tissues. A conical spring model is developed to predict soft tissue deformation with reference to deformation patterns. The model parameters are formulated according to tissue deformation patterns and the nonlinear behaviours of soft tissues are modelled with the stiffness variation of conical spring. Experimental results show that the proposed method can describe different tissue deformation patterns using one single equation and also exhibit the typical mechanical behaviours of soft tissues.

A suite of exercises for verifying dynamic earthquake rupture codes

USGS Publications Warehouse

Harris, Ruth A.; Barall, Michael; Aagaard, Brad T.; Ma, Shuo; Roten, Daniel; Olsen, Kim B.; Duan, Benchun; Liu, Dunyu; Luo, Bin; Bai, Kangchen; Ampuero, Jean-Paul; Kaneko, Yoshihiro; Gabriel, Alice-Agnes; Duru, Kenneth; Ulrich, Thomas; Wollherr, Stephanie; Shi, Zheqiang; Dunham, Eric; Bydlon, Sam; Zhang, Zhenguo; Chen, Xiaofei; Somala, Surendra N.; Pelties, Christian; Tago, Josue; Cruz-Atienza, Victor Manuel; Kozdon, Jeremy; Daub, Eric; Aslam, Khurram; Kase, Yuko; Withers, Kyle; Dalguer, Luis

2018-01-01

We describe a set of benchmark exercises that are designed to test if computer codes that simulate dynamic earthquake rupture are working as intended. These types of computer codes are often used to understand how earthquakes operate, and they produce simulation results that include earthquake size, amounts of fault slip, and the patterns of ground shaking and crustal deformation. The benchmark exercises examine a range of features that scientists incorporate in their dynamic earthquake rupture simulations. These include implementations of simple or complex fault geometry, off‐fault rock response to an earthquake, stress conditions, and a variety of formulations for fault friction. Many of the benchmarks were designed to investigate scientific problems at the forefronts of earthquake physics and strong ground motions research. The exercises are freely available on our website for use by the scientific community.

Research Spotlight: Extraordinary uplift of Yellowstone caldera

NASA Astrophysics Data System (ADS)

Tretkoff, Ernie

2011-02-01

In Yellowstone National Park, located in Wyoming, Montana, and Idaho, the Yellow­stone caldera, which extends about 40 kilometers by 60 kilometers, began in 2004 a period of accelerated uplift, with rates of uplift as high as 7 centimeters per year. From 2006 to 2009 the uplift rate slowed. Global Positioning System (GPS) and interferometric synthetic aperture radar (InSAR) ground deformation measurements described by Chang et al. show that in the northern caldera, uplift decreased from 7 centimeters per year in 2006 to 5 in 2008 and 2 in 2009. In the southwestern portion of the caldera, uplift decreased from 4 centimeters per year in 2006 to 2 in 2008 and 0.5 in 2009, demonstrating a spatial pattern of ground motion decrease from southwest to northeast along the caldera. (”Geophysical Research Letters, doi:10.1029/2010GL045451, 2010)

Ionospheric effects on DInSAR measurements of interseismic deformation in China

NASA Astrophysics Data System (ADS)

Gong, W.; Shan, X.; Song, X.; Liao, H.; Meyer, F. J.

2017-12-01

Interseismic deformation signals are small ground displacement that is critical to monitor the strain accumulates of major faults to foresee the potential seismic hazard. Accurate measurements of surface deformation could help recognize and interpret even subtle displacement and to give a better understanding of active fault behavior. However, the value and applicability of InSAR for inter-seismic monitoring problems is limited by the influence of temporal decorrelation and electromagnetic path delay variations (atmospheric disturbance), both reducing the sensitivity and accuracy of the technique. Ionospheric signal, a major part of atmospheric disturbance in InSAR, is related to the density of free electrons along the ray path, thus, that is dependent on the SAR signal frequency. Ionosphere induced phase distortions can lead to azimuth/range defocusing, geometry distortions and interferometric phase distortions. Some ionosphere phenomenon have been reported more severe at equatorial region and polar zones, e.g., ionosphere irregularity, while for middle latitude regions like West China it has not been thoroughly analyzed. Thus, this study is focus on the evaluation of ionosphere impacts in middle latitude zone, and its impacts in monitoring interseismic deformation in West China. The outcome would be useful to provide an empiric prior error condition of ionosphere disturbance, which can further benefit InSAR result interpretation and geophysical inversion, as well as the SAR data arrangement in future operational-(cloud) InSAR processing system. The study focus on two parts: 1. We will analyze the temporal-spatial variation of ionosphere and its magnitude at middle latitude zone, and investigate its impacts to current satellite SAR (C-band (Sentinel-1) and L-band (ALOS2) dataset) in earthquake-related deformation studies, especially inter-seismic study. 2. Ionosphere phase patterns at mid latitudes is typically small and the structure is compatibly smooth. This study will summarize the general spatial pattern of ionospheric phase at middle latitude zone and its impacts in fault displacement studies.

Combination of a pressure source and block movement for ground deformation analysis at Merapi volcano prior to the eruptions in 2006 and 2010

NASA Astrophysics Data System (ADS)

Aisyah, Nurnaning; Iguchi, Masato; Subandriyo; Budisantoso, Agus; Hotta, Kohei; Sumarti, Sri

2018-05-01

We analyzed ground deformation prior to the eruptions in 2006 and 2010 at Merapi volcano, Central Java, Indonesia. Ground deformation was monitored by electronic distance measurement (EDM) by measuring the slope distance toward 12 reflectors installed near the summit from five benchmarks on flanks every day. A large change of slope distance (CSD) was detected on the southeast and south baselines and a minor CSD was detected on the north and northwest baselines during the pre-eruptive stages of both the 2006 and 2010 eruptions. We applied a block movement model to the south and southeast baselines and a spherical pressure source model to the CSDs on the north and northwest baselines using the finite element method (FEM). The rates of block movement southward and the volume change of the pressure source increased on April 7, 2006 and continued at constant rates until the appearance of a new lava dome on April 26. Prior to the eruption in 2010, the block movement southeastward and the volume increase of the pressure source accelerated in the middle of October, and acceleration continued until the first outburst on October 26, 2010. Temporal patterns of the block movement and the increase in the volume of the pressure source correlate well with the increase in seismicity of VT and MP earthquakes. The pressure sources were obtained at a depth of 2 ± 0.5 km below the summit, and this position corresponds to the aseismic zone of VT earthquakes. Magma injection at the shallow part of this region causes an increase in the volume of the pressure source, and inflation of the ground of the summit triggered gravitational slip southeastward or southward of the ground surface. The volumes increases of the pressure sources were 9.7 ± 1 M m3 and 17.6 ± 0.8 M m3 in 2006 and 2010, respectively. The volume increase is related to the scale and type of the eruption. The effusive eruption in 2006 had a volcanic explosivity index (VEI) of 2 and the explosive eruption in 2010 had a VEI of 4. The directions and amounts of the block movement are strongly related to topography, hydrothermally weak zone and underground gap near the summit between West and East Domes.

Analysis of Mining Terrain Deformation Characteristics with Deformation Information System

NASA Astrophysics Data System (ADS)

Blachowski, Jan; Milczarek, Wojciech; Grzempowski, Piotr

2014-05-01

Mapping and prediction of mining related deformations of the earth surface is an important measure for minimising threat to surface infrastructure, human population, the environment and safety of the mining operation itself arising from underground extraction of useful minerals. The number of methods and techniques used for monitoring and analysis of mining terrain deformations is wide and increasing with the development of geographical information technologies. These include for example: terrestrial geodetic measurements, global positioning systems, remote sensing, spatial interpolation, finite element method modelling, GIS based modelling, geological modelling, empirical modelling using the Knothe theory, artificial neural networks, fuzzy logic calculations and other. The aim of this paper is to introduce the concept of an integrated Deformation Information System (DIS) developed in geographic information systems environment for analysis and modelling of various spatial data related to mining activity and demonstrate its applications for mapping and visualising, as well as identifying possible mining terrain deformation areas with various spatial modelling methods. The DIS concept is based on connected modules that include: the spatial database - the core of the system, the spatial data collection module formed by: terrestrial, satellite and remote sensing measurements of the ground changes, the spatial data mining module for data discovery and extraction, the geological modelling module, the spatial data modeling module with data processing algorithms for spatio-temporal analysis and mapping of mining deformations and their characteristics (e.g. deformation parameters: tilt, curvature and horizontal strain), the multivariate spatial data classification module and the visualization module allowing two-dimensional interactive and static mapping and three-dimensional visualizations of mining ground characteristics. The Systems's functionality has been presented on the case study of a coal mining region in SW Poland where it has been applied to study characteristics and map mining induced ground deformations in a city in the last two decades of underground coal extraction and in the first decade after the end of mining. The mining subsidence area and its deformation parameters (tilt and curvature) have been calculated and the latter classified and mapped according to the Polish regulations. In addition possible areas of ground deformation have been indicated based on multivariate spatial data analysis of geological and mining operation characteristics with the geographically weighted regression method.

An optical potential for the statically deformed actinide nuclei derived from a global spherical potential

NASA Astrophysics Data System (ADS)

Al-Rawashdeh, S. M.; Jaghoub, M. I.

2018-04-01

In this work we test the hypothesis that a properly deformed spherical optical potential, used within a channel-coupling scheme, provides a good description for the scattering data corresponding to neutron induced reactions on the heavy, statically deformed actinides and other lighter deformed nuclei. To accomplish our goal, we have deformed the Koning-Delaroche spherical global potential and then used it in a channel-coupling scheme. The ground-state is coupled to a sufficient number of inelastic rotational channels belonging to the ground-state band to ensure convergence. The predicted total cross sections, elastic and inelastic angular distributions are in good agreement with the experimental data. As a further test, we compare our results to those obtained by a global channel-coupled optical model whose parameters were obtained by fitting elastic and inelastic angular distributions in addition to total cross sections. Our results compare quite well with those obtained by the fitted, channel-coupled optical model. Below neutron incident energies of about 1MeV, our results show that scattering into the rotational excited states of the ground-state band plays a significant role in the scattering process and must be explicitly accounted for using a channel-coupling scheme.

Inventory of anthropogenic surface deformation measured by InSAR in the western U.S./Mexico and possible impacts on GPS measurements

NASA Astrophysics Data System (ADS)

Semple, A.; Pritchard, M. E.; Taylor, H.

2014-12-01

The western US and Mexico are deforming at several spatial scales that can be measured by ground and satellite observations like GPS and Interferometric Synthetic Aperture Radar (InSAR). Many GPS stations have been installed throughout this area to monitor ground deformation caused by large scale tectonic processes; however, several studies have noted that the data recorded at a GPS station can be contaminated by local, non-tectonic ground deformation. In this study, we use InSAR to examine deformation from various sources in the western US and Mexico. We chose this method due to the spatially large study area and the availability and temporal coverage of SAR imagery. We use SAR images acquired by the satellites Envisat, ERS-1 and ERS-2 over a time period from 1992-2010 to create several time series. Data from the ALOS satellite between 2006-2011 are also used in some areas. We use these time series analysis along with previously published results to observe and catalogue various sources of surface deformation in the western US and Mexico - from groundwater pumping, geothermal activity, mining, hydrocarbon production, and other sources. We then use these results to identify GPS stations that have potentially been contaminated by non-tectonic deformation signals. We document more than 150 distinct regions of non-tectonic and likely anthropogenic deformation. We have located 82 GPS stations within 20km of the center of at least one of the non-tectonic deformation signals we have identified. It is likely that the data from these 82 GPS stations have been contaminated by local anthropogenic deformation. Some examples of previously unpublished non-tectonic deformation we have seen in this study include but are not limited to, subsidence due to groundwater extraction in Jesus Garcia, Mexico, both uplift and subsidence due to natural gas extraction at Jonah Field in Sublette County, WY, and uplift due to a water recharge project in Tonopah, AZ.

Volumetric measurement of rock movement using photogrammetry

PubMed Central

Benton, Donovan J.; Iverson, Stephen R.; Martin, Lewis A.; Johnson, Jeffrey C.; Raffaldi, Michael J.

2016-01-01

NIOSH ground control safety research program at Spokane, Washington, is exploring applications of photogrammetry to rock mass and support monitoring. This paper describes two ways photogrammetric techniques are being used. First, photogrammetric data of laboratory testing is being used to correlate energy input and support deformation. This information can be used to infer remaining support toughness after ground deformation events. This technique is also demonstrated in a field application. Second, field photogrammetric data is compared to crackmeter data from a deep underground mine. Accuracies were found to average 8 mm, but have produced results within 0.2 mm of true displacement, as measured by crackmeters. Application of these techniques consists of monitoring overall fault activity by monitoring multiple points around the crackmeter. A case study is provided in which a crackmeter is clearly shown to have provided insufficient information regarding overall fault ground deformation. Photogrammetry is proving to be a useful ground monitoring tool due to its unobtrusiveness and ease of use. PMID:27110429

Elastic Coulomb breakup of 34Na

NASA Astrophysics Data System (ADS)

Singh, G.; Shubhchintak, Chatterjee, R.

2016-08-01

Background: 34Na is conjectured to play an important role in the production of seed nuclei in the alternate r -process paths involving light neutron rich nuclei very near the β -stability line, and as such, it is important to know its ground state properties and structure to calculate rates of the reactions it might be involved in, in the stellar plasma. Found in the region of `island of inversion', its ground state might not be in agreement with normal shell model predictions. Purpose: The aim of this paper is to study the elastic Coulomb breakup of 34Na on 208Pb to give us a core of 33Na with a neutron and in the process we try and investigate the one neutron separation energy and the ground state configuration of 34Na. Method: A fully quantum mechanical Coulomb breakup theory within the architecture of post-form finite range distorted wave Born approximation extended to include the effects of deformation is used to research the elastic Coulomb breakup of 34Na on 208Pb at 100 MeV/u. The triple differential cross section calculated for the breakup is integrated over the desired components to find the total cross-section, momentum, and angular distributions as well as the average momenta, along with the energy-angular distributions. Results: The total one neutron removal cross section is calculated to test the possible ground state configurations of 34Na. The average momentum results along with energy-angular calculations indicate 34Na to have a halo structure. The parallel momentum distributions with narrow full widths at half-maxima signify the same. Conclusion: We have attempted to analyze the possible ground state configurations of 34Na and in congruity with the patterns in the `island of inversion' conclude that even without deformation, 34Na should be a neutron halo with a predominant contribution to its ground state most probably coming from 33Na(3 /2+)⊗ 2 p3 /2ν configuration. We also surmise that it would certainly be useful and rewarding to test our predictions with an experiment to put stricter limits on its ground state configuration and binding energy.

Laboratory volcano geodesy

NASA Astrophysics Data System (ADS)

Færøvik Johannessen, Rikke; Galland, Olivier; Mair, Karen

2014-05-01

Magma transport in volcanic plumbing systems induces surface deformation, which can be monitored by geodetic techniques, such as GPS and InSAR. These geodetic signals are commonly analyzed through geodetic models in order to constrain the shape of, and the pressure in, magma plumbing systems. These models, however, suffer critical limitations: (1) the modelled magma conduit shapes cannot be compared with the real conduits, so the geodetic models cannot be tested nor validated; (2) the modelled conduits only exhibit shapes that are too simplistic; (3) most geodetic models only account for elasticity of the host rock, whereas substantial plastic deformation is known to occur. To overcome these limitations, one needs to use a physical system, in which (1) both surface deformation and the shape of, and pressure in, the underlying conduit are known, and (2) the mechanical properties of the host material are controlled and well known. In this contribution, we present novel quantitative laboratory results of shallow magma emplacement. Fine-grained silica flour represents the brittle crust, and low viscosity vegetable oil is an analogue for the magma. The melting temperature of the oil is 31°C; the oil solidifies in the models after the end of the experiments. At the time of injection the oil temperature is 50°C. The oil is pumped from a reservoir using a volumetric pump into the silica flour through a circular inlet at the bottom of a 40x40 cm square box. The silica flour is cohesive, such that oil intrudes it by fracturing it, and produces typical sheet intrusions (dykes, cone sheets, etc.). During oil intrusion, the model surface deforms, mostly by doming. These movements are measured by an advanced photogrammetry method, which uses 4 synchronized fixed cameras that periodically image the surface of the model from different angles. We apply particle tracking method to compute the 3D ground deformation pattern through time. After solidification of the oil, the intrusion can be excavated and photographed from several angles to compute its 3D shape with the same photogrammetry method. Then, the surface deformation pattern can be directly compared with the shape of underlying intrusion. This quantitative dataset is essential to quantitatively test and validate classical volcano geodetic models.

Method for measuring residual stresses in materials by plastically deforming the material and interference pattern comparison

DOEpatents

Pechersky, Martin J.

1995-01-01

A method for measuring residual stress in a material comprising the steps of establishing a speckle pattern on the surface with a first laser then heating a portion of that pattern with an infrared laser until the surface plastically deforms. Comparing the speckle patterns before and after deformation by subtracting one pattern from the other will produce a fringe pattern that serves as a visual and quantitative indication of the degree to which the plasticized surface responded to the stress dung heating and enables calculation of the stress.

Observations of coupled seismicity and ground deformation at El Hierro Island (2011-2014)

NASA Astrophysics Data System (ADS)

Gonzalez, P. J.

2015-12-01

New insights into the magma storage and evolution at oceanic island volcanoes are now being achieved using remotely sensed space geodetic techniques, namely satellite radar interferometry. Differential radar interferometry is a technique tracking, at high spatial resolution, changes in the travel-time (distance) from the satellites to the ground surface, having wide applications in Earth sciences. Volcanic activity usually is accompanied by surface ground deformation. In many instances, modelling of surface deformation has the great advantage to estimate the magma volume change, a particularly interesting parameter prior to eruptions. Jointly interpreted with petrology, degassing and seismicity, it helps to understand the crustal magmatic systems as a whole. Current (and near-future) radar satellite missions will reduce the revisit time over global sub-aerial volcanoes to a sub-weekly basis, which will increase the potential for its operational use. Time series and filtering processing techniques of such streaming data would allow to track subsurface magma migration with high precision, and frequently update over vast areas (volcanic arcs, large caldera systems, etc.). As an example for the future potential monitoring scenario, we analyze multiple satellite radar data over El Hierro Island (Canary Islands, Spain) to measure and model surface ground deformation. El Hierro has been active for more than 3 years (2011 to 2014). Initial phases of the unrest culminated in a submarine eruption (late 2011 - early 2012). However, after the submarine eruption ended, its magmatic system still active and affected by pseudo-regular energetic seismic swarms, accompanied by surface deformation without resumed eruptions. Such example is a great opportunity to understand the crustal magmatic systems in low magma supply-rate oceanic island volcanoes. This new approach to measure surface deformation processes is yielding an ever richer level of information from volcanology to engineering and meteorological monitoring problems.

InSAR-detected Local Ground Inflation Prior to Small Phreatic Eruption

NASA Astrophysics Data System (ADS)

Kobayashi, T.; Morishita, Y.

2017-12-01

Phreatic eruptions may be related to transient pressure changes in subsurface regions of hydrothermal systems. It means that crustal deformation presumably proceeds with the pressure increase under the ground, which can be a kind of precursor. In this context, Mt. Hakone volcano is a good study target. This is because the crustal deformation has been successfully detected two months before small phreatic eruptions at an active geothermal area, called Owaku-dani. The anomalous activity such as an increase of seismicity started in the end of April, 2015. With this anomalous activity, SAR (ALOS-2) observations was conducted, and small but significant crustal deformation was detected in a local area with a diameter of 200 m with a displacement of 5 cm. The amount of deformation has increased with time although the spatial size has not changed, and resultantly the amount reached up to 60 cm. Finally, in the end of June, eruptions occurred just at the local crustal deformation area. It should be noted that the eruption started from the InSAR-detected inflational area. This is an excellent case that we were able to identify the location of small phreatic eruption in advance by detecting anomalous ground inflation. Further, we investigated whether or not the inflational deformation preceded the anomalous activity observed since the end of April. Applying InSAR time series analysis incorporating the phase linking method to C-band SAR data of RADARSAT-2 (RS2) and Sentinel-1A (S1), we successfully detected small but significant inflational ground deformation that has already proceeded since the end of 2014 at the latest. The amount of deformation reaches up to 3 cm during 4 months. The most striking point is that the spatial distribution is quite similar to the deformation detected by ALOS-2. It strongly suggests that the pressure increase in subsurface have already started before the anomalous activities such as seismic swarm and widely-distributed deformation have been identified. Acknowledgements: ALOS-2 and RS2 data were provided from JAXA under a cooperative research contract between GSI and JAXA, and in addition, for RS2 under a contract between JAXA and CSA. The ownership of ALOS-2 and RS2 data belong to JAXA and MDA, respectively. This study was supported by JSPS KAKENHI Grant Numbers JP16K1779.

Ground deformation monitoring using small baseline DInSAR technique: A case study in Taiyuan City from 2003 to 2009

USGS Publications Warehouse

Wu, H.-A.; Zhang, Y.-H.; Chen, X.-Y.; Lu, T.; Du, J.; Sun, Z.-H.; Sun, G.-T.

2011-01-01

DInSAR technique based on time series of SAR images has been very popular to monitor ground stow deformation in recent years such as permanent scatterers (PS) method small baseline subsets (SBAS) method and coherent targets (CT) method. By taking advantage of PS method and CT method in this paper small baseline DTnSAR technique is used to investigate the ground deformation of Taiyuan City Shanxi Province from 2003 to 2009 by using 23 ENVISAT ASAR images. The experiment results demonstrate that: (1) during this period four significant subsidence centers have been developed in Taiyuan namely Xiayuan Wujiabu Xiaodian Sunjiazhai. The largest subsidence center is Sunjiazhai with an average subsidence rate of -77. 28 mm/a; (2) The subsidence of the old center Wanbolin has sHowed down. And the subsidence in the northern region has stopped and some areas even rebounded. (3) The change of subsidence centers indicates that the control measures of "closing wells and reducing exploitation" taken by the Taiyuan government has achieved initial effects. (4) The experiment results have been validated with leveling data and the acouracy is 2. 90 mm which shows that the small baseline DInSAR technique can be used to monitor urban ground deformation.

Crustal deformation evidences for viscous coupling and fragmented lithosphere at the Nubia-Iberia plate boundary (Western Mediterranean)

NASA Astrophysics Data System (ADS)

Palano, Mimmo; González, Pablo J.; Fernández, José

2016-04-01

A spatially dense crustal velocity field, based on up to 15 years of GNSS observations at more than 380 sites and extensively covering the Iberian Peninsula and Northern Africa, allow us to provide new insights into two main tectonic processes currently occurring in this area. We detected a slow large-scale clockwise rotation of the Iberian Peninsula with respect to a local pole located closely to the northwestern sector of the Pyrenean mountain range (Palano et al., 2015). Although this crustal deformation pattern could suggest a rigid rotating lithosphere block, this model would predict significant shortening along the Western (off-shore Lisbon) and North Iberian margin which cannot totally ruled out but currently is not clearly observed. Conversely, we favour the interpretation that this pattern reflects the quasi-continuous straining of the ductile lithosphere in some sectors of South and Western Iberia in response to viscous coupling of the NW Nubia and Iberian plate boundary in the Gulf of Cádiz. Furthermore, the western Mediterranean basin appears fragmented into independent crustal tectonic blocks, which delimited by inherited lithospheric shear structures and trapped within the Nubia-Eurasia collision, are currently accommodating most of the plate convergence rate. Among these blocks, an (oceanic-like western) Algerian one is currently transferring a significant fraction of the Nubia-Eurasia convergence rate into the Eastern Betics (SE Iberia) and likely causing the eastward motion of the Baleares Promontory. Most of the observed crustal ground deformation can be attributed to processes driven by spatially variable lithospheric plate forces imposed along the Nubia-Eurasia convergence boundary. Nevertheless, the observed deformation field infers a very low convergence rates as observed also at the eastern side of the western Mediterranean, along the Calabro Peloritan Arc, by space geodesy (e.g. Palano, 2015). References Palano M. (2015). On the present-day crustal stress, strain-rate fields and mantle anisotropy pattern of Italy. Geophysical Journal International, 200 (2), 969-985, doi:10.1093/gji/ggu451. Palano M., González P. J., Fernández J. (2015). The diffuse plate boundary of Nubia and Iberia in the Western Mediterranean: crustal deformation evidence for viscous coupling and fragmented lithosphere. Earth and Planetary Science Letters, 430, 439-447, doi:10.1016/j.epsl.2015.08.040.

Arctic and subarctic environmental analyses utilizing ERTS-1 imagery

NASA Technical Reports Server (NTRS)

Anderson, D. M. (Principal Investigator); Mckim, H. L.; Gatto, L. W.; Haugen, R. K.; Crowder, W. K.; Slaughter, C. W.; Marlar, T. L.

1974-01-01

The author has identified the following significant results. ERTS-1 imagery provides a means of distinguishing and monitoring estuarine surface water circulation patterns and changes in the relative sediment load of discharging rivers on a regional basis. Physical boundaries mapped from ERTS-1 imagery in combination with ground truth obtained from existing small scale maps and other sources resulted in improved and more detailed maps of permafrost terrain and vegetation for the same area. Snowpack cover within a research watershed has been analyzed and compared to ground data. Large river icings along the proposed Alaska pipeline route from Prudhoe Bay to the Brooks Range have been monitored. Sea ice deformation and drift northeast of Point Barrow, Alaska have been measured during a four day period in March and shore-fast ice accumulation and ablation along the west coast of Alaska have been mapped for the spring and early summer seasons.

Close-range photogrammetry in underground mining ground control

NASA Astrophysics Data System (ADS)

Benton, Donovan J.; Chambers, Amy J.; Raffaldi, Michael J.; Finley, Seth A.; Powers, Mark J.

2016-09-01

Monitoring underground mine deformation and support conditions has traditionally involved visual inspection and geotechnical instrumentation. Monitoring displacements with conventional instrumentation can be expensive and time-consuming, and the number of locations that can be effectively monitored is generally limited. Moreover, conventional methods typically produce vector rather than tensor descriptions of geometry changes. Tensor descriptions can provide greater insight into hazardous ground movements, particularly in recently excavated openings and in older workings that have been negatively impacted by high stress concentrations, time-dependent deformation, or corrosion of ground support elements. To address these issues, researchers with the National Institute for Occupational Safety and Health, Spokane Mining Research Division are developing and evaluating photogrammetric systems for ground control monitoring applications in underground mines. This research has demonstrated that photogrammetric systems can produce millimeter-level measurements that are comparable to conventional displacement-measuring instruments. This paper provides an overview of the beneficial use of close-range photogrammetry for the following three ground control applications in underground mines: monitoring the deformation of surface support, monitoring rock mass movement, and monitoring the corrosion of surface support. Preliminary field analyses, case studies, limitations, and best practices for these applications are also discussed.

Quantitative assessment of soft tissue deformation using digital speckle pattern interferometry: studies on phantom breast models.

PubMed

Karuppanan, Udayakumar; Unni, Sujatha Narayanan; Angarai, Ganesan R

2017-01-01

Assessment of mechanical properties of soft matter is a challenging task in a purely noninvasive and noncontact environment. As tissue mechanical properties play a vital role in determining tissue health status, such noninvasive methods offer great potential in framing large-scale medical screening strategies. The digital speckle pattern interferometry (DSPI)-based image capture and analysis system described here is capable of extracting the deformation information from a single acquired fringe pattern. Such a method of analysis would be required in the case of the highly dynamic nature of speckle patterns derived from soft tissues while applying mechanical compression. Soft phantoms mimicking breast tissue optical and mechanical properties were fabricated and tested in the DSPI out of plane configuration set up. Hilbert transform (HT)-based image analysis algorithm was developed to extract the phase and corresponding deformation of the sample from a single acquired fringe pattern. The experimental fringe contours were found to correlate with numerically simulated deformation patterns of the sample using Abaqus finite element analysis software. The extracted deformation from the experimental fringe pattern using the HT-based algorithm is compared with the deformation value obtained using numerical simulation under similar conditions of loading and the results are found to correlate with an average %error of 10. The proposed method is applied on breast phantoms fabricated with included subsurface anomaly mimicking cancerous tissue and the results are analyzed.

Interferometric synthetic aperture radar (InSAR)—its past, present and future

USGS Publications Warehouse

Lu, Zhong; Kwoun, Oh-Ig; Rykhus, R.P.

2007-01-01

Very simply, interferometric synthetic aperture radar (InSAR) involves the use of two or more synthetic aperture radar (SAR) images of the same area to extract landscape topography and its deformation patterns. A SAR system transmits electromagnetic waves at a wavelength that can range from a few millimeters to tens of centimeters and therefore can operate during day and night under all-weather conditions. Using SAR processing technique (Curlander and McDonough, 1991), both the intensity and phase of the reflected (or backscattered) radar signal of each ground resolution element (a few meters to tens of meters) can be calculated in the form of a complex-valued SAR image that represents the reflectivity of the ground surface. The amplitude or intensity of the SAR image is determined primarily by terrain slope, surface roughness, and dielectric constants, whereas the phase of the SAR image is determined primarily by the distance between the satellite antenna and the ground targets. InSAR imaging utilizes the interaction of electromagnetic waves, referred to as interference, to measure precise distances between the satellite antenna and ground resolution elements to derive landscape topography and its subtle change in elevation.

The effect of short ground vegetation on terrestrial laser scans at a local scale

NASA Astrophysics Data System (ADS)

Fan, Lei; Powrie, William; Smethurst, Joel; Atkinson, Peter M.; Einstein, Herbert

2014-09-01

Terrestrial laser scanning (TLS) can record a large amount of accurate topographical information with a high spatial accuracy over a relatively short period of time. These features suggest it is a useful tool for topographical survey and surface deformation detection. However, the use of TLS to survey a terrain surface is still challenging in the presence of dense ground vegetation. The bare ground surface may not be illuminated due to signal occlusion caused by vegetation. This paper investigates vegetation-induced elevation error in TLS surveys at a local scale and its spatial pattern. An open, relatively flat area vegetated with dense grass was surveyed repeatedly under several scan conditions. A total station was used to establish an accurate representation of the bare ground surface. Local-highest-point and local-lowest-point filters were applied to the point clouds acquired for deriving vegetation height and vegetation-induced elevation error, respectively. The effects of various factors (for example, vegetation height, edge effects, incidence angle, scan resolution and location) on the error caused by vegetation are discussed. The results are of use in the planning and interpretation of TLS surveys of vegetated areas.

MetaSensing's FastGBSAR: ground based radar for deformation monitoring

NASA Astrophysics Data System (ADS)

Rödelsperger, Sabine; Meta, Adriano

2014-10-01

The continuous monitoring of ground deformation and structural movement has become an important task in engineering. MetaSensing introduces a novel sensor system, the Fast Ground Based Synthetic Aperture Radar (FastGBSAR), based on innovative technologies that have already been successfully applied to airborne SAR applications. The FastGBSAR allows the remote sensing of deformations of a slope or infrastructure from up to a distance of 4 km. The FastGBSAR can be setup in two different configurations: in Real Aperture Radar (RAR) mode it is capable of accurately measuring displacements along a linear range profile, ideal for monitoring vibrations of structures like bridges and towers (displacement accuracy up to 0.01 mm). Modal parameters can be determined within half an hour. Alternatively, in Synthetic Aperture Radar (SAR) configuration it produces two-dimensional displacement images with an acquisition time of less than 5 seconds, ideal for monitoring areal structures like dams, landslides and open pit mines (displacement accuracy up to 0.1 mm). The MetaSensing FastGBSAR is the first ground based SAR instrument on the market able to produce two-dimensional deformation maps with this high acquisition rate. By that, deformation time series with a high temporal and spatial resolution can be generated, giving detailed information useful to determine the deformation mechanisms involved and eventually to predict an incoming failure. The system is fully portable and can be quickly installed on bedrock or a basement. The data acquisition and processing can be fully automated leading to a low effort in instrument operation and maintenance. Due to the short acquisition time of FastGBSAR, the coherence between two acquisitions is very high and the phase unwrapping is simplified enormously. This yields a high density of resolution cells with good quality and high reliability of the acquired deformations. The deformation maps can directly be used as input into an Early Warning system, to determine the state and danger of a slope or structure. In this paper, the technical principles of the instrument are described and case studies of different monitoring tasks are presented.

Implications of ground-deformation measurements across earth fissures in subsidence areas in the southwestern USA

USGS Publications Warehouse

Holzer, Thomas L.

2010-01-01

Ground deformation was monitored at earth fissures in areas of land subsidence induced by groundwater extraction in the southwestern United States. The ground deformation is consistent with the mechanism that fissures are caused by horizontal strains generated by bending of overburden in response to localized differential compaction. Subsidence profiles indicated that localized differential subsidence occurred across the fissures and that maximum convex-upward curvature was at the fissure. The overall shape of the profile stayed similar with time, and maximum curvature remained stationary at the fissure. Horizontal displacements were largest near the fissure, and generally were small to negligible away from the fissure. Maximum tensile horizontal strains were at the fissure and coincided with maximum curvature in the subsidence profiles. Horizontal tensile strain continued to accumulate at fissures after they formed with rates of opening ranging from 30 to 120 microstrain/year at fissures in Arizona.

Ring-fault activity at subsiding calderas studied from analogue experiments and numerical modeling

NASA Astrophysics Data System (ADS)

Liu, Y. K.; Ruch, J.; Vasyura-Bathke, H.; Jonsson, S.

2017-12-01

Several subsiding calderas, such as the ones in the Galápagos archipelago and the Axial seamount in the Pacific Ocean have shown a complex but similar ground deformation pattern, composed of a broad deflation signal affecting the entire volcanic edifice and of a localized subsidence signal focused within the caldera. However, it is still debated how deep processes at subsiding calderas, including magmatic pressure changes, source locations and ring-faulting, relate to this observed surface deformation pattern. We combine analogue sandbox experiments with numerical modeling to study processes involved from initial subsidence to later collapse of calderas. The sandbox apparatus is composed of a motor driven subsiding half-piston connected to the bottom of a glass box. During the experiments the observation is done by five digital cameras photographing from various perspectives. We use Photoscan, a photogrammetry software and PIVLab, a time-resolved digital image correlation tool, to retrieve time-series of digital elevation models and velocity fields from acquired photographs. This setup allows tracking the processes acting both at depth and at the surface, and to assess their relative importance as the subsidence evolves to a collapse. We also use the Boundary Element Method to build a numerical model of the experiment setup, which comprises contracting sill-like source in interaction with a ring-fault in elastic half-space. We then compare our results from these two approaches with the examples observed in nature. Our preliminary experimental and numerical results show that at the initial stage of magmatic withdrawal, when the ring-fault is not yet well formed, broad and smooth deflation dominates at the surface. As the withdrawal increases, narrower subsidence bowl develops accompanied by the upward propagation of the ring-faulting. This indicates that the broad deflation, affecting the entire volcano edifice, is primarily driven by the contraction of the magmatic source, whereas the ring-faulting tends to concentrate deformation within the caldera. This interaction between ring-faulting and pressure decrease in a magma reservoir therefore provides a possible explanation for the deformation pattern observed at several subsiding calderas.

Plate Like Convection with Viscous Strain Weakening and Corresponding Surface Deformation Pattern

NASA Astrophysics Data System (ADS)

Fuchs, L.; Becker, T. W.

2017-12-01

How plate tectonic surface motions are generated by mantle convection on Earth and possibly other terrestrial type planets has recently become more readily accessible with fully dynamic convection computations. However, it remains debated how plate-like the behavior in such models truly is, and in particular how the well plate boundary dynamics are captured in models which typically exclude the effects of deformation history and memory. Here, we analyze some of the effects of viscous strain weakening on plate behavior and the interactions between interior convection dynamics and surface deformation patterns. We use the finite element code CitcomCU to model convection in a 3D Cartesian model setup. The models are internally heated, with an Arrhenius-type temperature dependent viscosity including plastic yielding and viscous strain weakening (VSW) and healing (VSWH). VSW can mimic first order features of more complex damage mechanisms such as grain-size dependent rheology. Besides plate diagnostic parameters (Plateness, Mobility, and Toroidal: Poloidal ratio) to analyze the tectonic behavior our models, we also explore how "plate boundaries" link to convective patterns. In a first model series, we analyze general surface deformation patterns without VSW. In the early stages, deformation patterns are clearly co-located with up- and downwelling limbs of convection. Along downwellings strain-rates are high and localized, whereas upwellings tend to lead to broad zones of high deformation. At a more advanced stage, however, the plates' interior is highly deformed due to continuous strain accumulation and resurfaced inherited strain. Including only VSW leads to more localized deformation along downwellings. However, at a more advanced stage plate-like convection fails due an overall weakening of the material. This is prevented including strain healing. Deformation pattern at the surface more closely coincide with the internal convection patterns. The average surface deformation is reduced significantly and mainly governed by the location of the up- and downwellings. VSWH thereby affects plate dynamics due to two main properties: the intensity of weakening with increasing strain and the strain healing rate. As both increase, mobility increases as well and strain becomes more localized at the downwellings.

10 CFR 100.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... input at the oscillators' supports. Safe Shutdown Earthquake Ground Motion is the vibratory ground... forces. Tectonic surface deformation is associated with earthquake processes. Testing reactor means a...

10 CFR 100.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... input at the oscillators' supports. Safe Shutdown Earthquake Ground Motion is the vibratory ground... forces. Tectonic surface deformation is associated with earthquake processes. Testing reactor means a...

Quantification of the fraction poorly deformable red blood cells using ektacytometry.

PubMed

Streekstra, G J; Dobbe, J G G; Hoekstra, A G

2010-06-21

We describe a method to obtain the fraction of poorly deformable red blood cells in a blood sample from the intensity pattern in an ektacytometer. In an ektacytometer red blood cells are transformed into ellipsoids by a shear flow between two transparent cylinders. The intensity pattern, due to a laser beam that is sent through the suspension, is projected on a screen. When measuring a healthy red blood cell population iso-intensity curves are ellipses with an axial ratio equal to that of the average red blood cell. In contrast poorly deformable cells result in circular iso-intensity curves. In this study we show that for mixtures of deformable and poorly deformable red blood cells, iso-intensity curves in the composite intensity pattern are neither elliptical nor circular but obtain cross-like shapes. We propose a method to obtain the fraction of poorly deformable red blood cells from those intensity patterns. Experiments with mixtures of poorly deformable and deformable red blood cells validate the method and demonstrate its accuracy. In a clinical setting our approach is potentially of great value for the detection of the fraction of sickle cells in blood samples of patients with sickle cell disease or to find a measure for the parasitemia in patients infected with malaria.

Ground Deformation from Chilean Volcanic Eruption Shown by Satellite Radar Image

NASA Image and Video Library

2015-04-29

This satellite interferometric synthetic aperture radar image-pair shows relative deformation of the Earth surface when nn April 22-23, 2015, significant explosive eruptions occurred at Calbuco volcano, Chile.

Coupled reservoir-geomechanical analysis of CO2 injection and ground deformations at In Salah, Algeria

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rutqvist, J.; Vasco, D.W.; Myer, L.

2009-11-01

In Salah Gas Project in Algeria has been injecting 0.5-1 million tonnes CO{sub 2} per year over the past five years into a water-filled strata at a depth of about 1,800 to 1,900 m. Unlike most CO{sub 2} storage sites, the permeability of the storage formation is relatively low and comparatively thin with a thickness of about 20 m. To ensure adequate CO{sub 2} flow-rates across the low-permeability sand-face, the In Salah Gas Project decided to use long-reach (about 1 to 1.5 km) horizontal injection wells. In an ongoing research project we use field data and coupled reservoir-geomechanical numerical modelingmore » to assess the effectiveness of this approach and to investigate monitoring techniques to evaluate the performance of a CO{sub 2}-injection operation in relatively low permeability formations. Among the field data used are ground surface deformations evaluated from recently acquired satellite-based inferrometry (InSAR). The InSAR data shows a surface uplift on the order of 5 mm per year above active CO{sub 2} injection wells and the uplift pattern extends several km from the injection wells. In this paper we use the observed surface uplift to constrain our coupled reservoir-geomechanical model and conduct sensitivity studies to investigate potential causes and mechanisms of the observed uplift. The results of our analysis indicates that most of the observed uplift magnitude can be explained by pressure-induced, poro-elastic expansion of the 20 m thick injection zone, but there could also be a significant contribution from pressure-induced deformations within a 100 m thick zone of shaly sands immediately above the injection zone.« less

Methodology for heritage conservation in Belgium based on multi-temporal interferometry

NASA Astrophysics Data System (ADS)

Bejarano-Urrego, L.; Verstrynge, E.; Shimoni, M.; Lopez, J.; Walstra, J.; Declercq, P.-Y.; Derauw, D.; Hayen, R.; Van Balen, K.

2017-09-01

Soil differential settlements that cause structural damage to heritage buildings are precipitating cultural and economic value losses. Adequate damage assessment as well as protection and preservation of the built patrimony are priorities at national and local levels, so they require advanced integration and analysis of environmental, architectural and historical parameters. The GEPATAR project (GEotechnical and Patrimonial Archives Toolbox for ARchitectural conservation in Belgium) aims to create an online interactive geo-information tool that allows the user to view and to be informed about the Belgian heritage buildings at risk due to differential soil settlements. Multi-temporal interferometry techniques (MTI) have been proven to be a powerful technique for analyzing earth surface deformation patterns through time series of Synthetic Aperture Radar (SAR) images. These techniques allow to measure ground movements over wide areas at high precision and relatively low cost. In this project, Persistent Scatterer Synthetic Aperture Radar Interferometry (PS-InSAR) and Multidimensional Small Baseline Subsets (MSBAS) are used to measure and monitor the temporal evolution of surface deformations across Belgium. This information is integrated with the Belgian heritage data by means of an interactive toolbox in a GIS environment in order to identify the level of risk. At country scale, the toolbox includes ground deformation hazard maps, geological information, location of patrimony buildings and land use; while at local scale, it includes settlement rates, photographic and historical surveys as well as architectural and geotechnical information. Some case studies are investigated by means of on-site monitoring techniques and stability analysis to evaluate the applied approaches. This paper presents a description of the methodology being implemented in the project together with the case study of the Saint Vincent's church which is located on a former colliery zone. For this building, damage is assessed by means of PSInSAR.

Causes of unrest at silicic calderas in the East African Rift: New constraints from InSAR and soil-gas chemistry at Aluto volcano, Ethiopia

NASA Astrophysics Data System (ADS)

Hutchison, William; Biggs, Juliet; Mather, Tamsin A.; Pyle, David M.; Lewi, Elias; Yirgu, Gezahegn; Caliro, Stefano; Chiodini, Giovanni; Clor, Laura E.; Fischer, Tobias P.

2016-08-01

Restless silicic calderas present major geological hazards, and yet many also host significant untapped geothermal resources. In East Africa, this poses a major challenge, although the calderas are largely unmonitored their geothermal resources could provide substantial economic benefits to the region. Understanding what causes unrest at these volcanoes is vital for weighing up the opportunities against the potential risks. Here we bring together new field and remote sensing observations to evaluate causes of ground deformation at Aluto, a restless silicic volcano located in the Main Ethiopian Rift (MER). Interferometric Synthetic Aperture Radar (InSAR) data reveal the temporal and spatial characteristics of a ground deformation episode that took place between 2008 and 2010. Deformation time series reveal pulses of accelerating uplift that transition to gradual long-term subsidence, and analytical models support inflation source depths of ˜5 km. Gases escaping along the major fault zone of Aluto show high CO2 flux, and a clear magmatic carbon signature (CO2-δ13C of -4.2‰ to -4.5‰). This provides compelling evidence that the magmatic and hydrothermal reservoirs of the complex are physically connected. We suggest that a coupled magmatic-hydrothermal system can explain the uplift-subsidence signals. We hypothesize that magmatic fluid injection and/or intrusion in the cap of the magmatic reservoir drives edifice-wide inflation while subsequent deflation is related to magmatic degassing and depressurization of the hydrothermal system. These new constraints on the plumbing of Aluto yield important insights into the behavior of rift volcanic systems and will be crucial for interpreting future patterns of unrest.

InSAR imaging of volcanic deformation over cloud-prone areas - Aleutian islands

USGS Publications Warehouse

Lu, Zhong

2007-01-01

Interferometric synthetic aperture radar (INSAR) is capable of measuring ground-surface deformation with centimeter-tosubcentimeter precision and spatial resolution of tens-of meters over a relatively large region. With its global coverage and all-weather imaging capability, INSAR is an important technique for measuring ground-surface deformation of volcanoes over cloud-prone and rainy regions such as the Aleutian Islands, where only less than 5 percent of optical imagery is usable due to inclement weather conditions. The spatial distribution of surface deformation data, derived from INSAR images, enables the construction of detailed mechanical models to enhance the study of magmatic processes. This paper reviews the basics of INSAR for volcanic deformation mapping and the INSAR studies of ten Aleutian volcanoes associated with both eruptive and noneruptive activity. These studies demonstrate that all-weather INSAR imaging can improve our understanding of how the Aleutian volcanoes work and enhance our capability to predict future eruptions and associated hazards.

Insights into the dynamics of Etna volcano from 20-year time span microgravity and GPS observations

NASA Astrophysics Data System (ADS)

Bonforte, Alessandro; Fanizza, Giovanni; Greco, Filippo; Matera, Alfredo; Sulpizio, Roberto

2016-04-01

A common ground deformation and microgravity array of benchmarks lies on the southern slope of Mt. Etna volcano and is routinely measured by GPS and relative gravimetry methods. The array was installed for monitoring the ground motion and underground mass changes along the southern rift of the volcano and data are usually processed and interpreted independently. The benchmarks have been installed mainly along a main road crossing the southern side of the volcano with an E-W direction and reaching 2000 m of altitude. The gravity array covers the entire path of the road, while the ground deformation one only the upper one, due to the woods at lower altitude preventing good GPS measurements. Furthermore, microgravity surveys are usually carried out more frequently with respect to the GPS ones. In this work, an integrated analysis of microgravity and ground deformation is performed over a 20-year time span (1994-2014). Gravity variations have been first corrected for the free-air effect using the GPS observed vertical deformation and the theoretical vertical gravity gradient (-308.6 μGal/m). The free-air corrected gravity changes were then reduced from the high frequency variations (noise) and the seasonal fluctuations, mainly due to water-table fluctuations. This long-term dataset constitutes a unique opportunity to examine the behavior of Etna in a period in which the volcano exhibited different styles of activity characterized by recharging phases, flank eruptions and fountaining episodes. The gravity and deformation data allow investigating the response of the volcano in a wider perspective providing insights into the definition of its dynamic behavior and posing the basis to track the unrest evolution and to forecast the style of the eruption. The joint analysis highlights common periods, in which the signals underwent contemporaneous changes occurring mainly in the central and eastern stations. On the other hand, no significant changes in the behavior of deformation and gravity signals have been observed in the westernmost stations. Specifically, we observed at least four periods characterized by different correlation between the two time series. Indeed, the integrated analysis of the spatio-temporal variations of the gravity and the ground deformation data highlights different volcanic processes controlling the dynamical behavior of Etna volcano in this sector.

U.S. Geological Survey Subsidence Interest Group Conference : proceedings of the Technical Meeting, Galveston, Texas, November 27-29, 2001

USGS Publications Warehouse

Prince, Keith R.; Galloway, Devin L.

2003-01-01

InSAR is a powerful technique that uses radar data acquired at different times to measure land-surface deformation, or displacement, over large areas at a high level of spatial detail and a high degree of measurement resolution. InSAR displacement maps (interferograms), in conjunction with other hydrogeologic data, have been used to determine aquifer-system characteristics for areas where surface deformation is the result of stress induced changes in the granular skeleton of the aquifer system. Interferograms and measurements of aquifer-system compaction from borehole extensometers, and ground-water levels in wells in Santa Clara Valley, California, have shown that land-surface changes caused by aquifer-system deformation for September 23, 1992-August 2, 1997, are elastic (reversible): During the summer when water levels are declining, the land surface subsides, and during the winter when water levels are recovering, the land surface uplifts, resulting in no net surface deformation. Interferograms used with fault maps of Santa Clara Valley and of Las Vegas Valley, Nevada, have shown that the extent of regional land-surface changes caused by aquifer-system deformation may be partially controlled by faults. Interferograms of Yucca Flat, Nevada, show subsidence associated with the recovery of elevated hydraulic heads caused by underground weapons testing at depths of more than 600 meters. For these selected case studies, continuing or renewed deformation of the aquifer system is coupled with pore-fluid-pressure changes. When applied stresses (water-level changes) can be measured accurately for periods that the interferograms show displacement, stress-strain relations, and thus bulk storage properties, can be evaluated. For areas where additional ground-water-level, land-surface-elevation, aquifer-system-compaction, or other environmental data are needed, the interferograms can be used as a guide for designing appropriate monitoring networks. Aquifer-system properties derived from stress-strain relations and identification of hidden faults, other structural or stratigraphic controls on deformation and ground-water flow, and other hydrogeologic boundaries in the flow system can be used to constrain numerical ground-water flow and subsidence simulations. Managing aquifer systems within optimal limits may be possible if regions susceptible to ground-water depletion and the accompanying land subsidence can be identified and characterized.

The Deformation of Overburden Soil and Interaction with Pile Foundations of Bridges Induced by Normal Faulting

NASA Astrophysics Data System (ADS)

Wu, Liang-Chun; Li, Chien-Hung; Chan, Pei-Chen; Lin, Ming-Lang

2017-04-01

According to the investigations of well-known disastrous earthquakes in recent years, ground deformation induced by faulting is one of the causes for engineering structure damages in addition to strong ground motion. Most of structures located on faulting zone has been destroyed by fault offset. Take the Norcia Earthquake in Italy (2016, Mw=6.2) as an example, the highway bridge in Arquata crossing the rupture area of the active normal fault suffered a quantity of displacement which causing abutment settlement, the piers of bridge fractured and so on. However, The Seismic Design Provisions and Commentary for Highway Bridges in Taiwan, the stating of it in the general rule of first chapter, the design in bridges crossing active fault: "This specification is not applicable of making design in bridges crossing or near active fault, that design ought to the other particular considerations ".This indicates that the safty of bridges crossing active fault are not only consider the seismic performance, the most ground deformation should be attended. In this research, to understand the failure mechanism and the deformation characteristics, we will organize the case which the bridges subjected faulting at home and abroad. The processes of research are through physical sandbox experiment and numerical simulation by discrete element models (PFC3-D). The normal fault case in Taiwan is Shanchiao Fault. As above, the research can explore the deformation in overburden soil and the influences in the foundations of bridges by normal faulting. While we can understand the behavior of foundations, we will make the bridge superstructures into two separations, simple beam and continuous beam and make a further research on the main control variables in bridges by faulting. Through the above mentioned, we can then give appropriate suggestions about planning considerations and design approaches. This research presents results from sandbox experiment and 3-D numerical analysis to simulate overburden soil and embedded pile foundations subjected to normal faulting. In order to validate this numerical model, it is compared to sandbox experiments. Since the 3-D numerical analysis corresponds to the sandbox expeiments, the response of pile foundations and ground deformation induced by normal faulting are discussed. To understand the 3-D behavior of ground deformation and pile foundations, the observation such as the triangular shear zone, the width of primary deformation zone and the inclination, displacements, of the pile foundations are discussed in experiments and simulations. Furthermore, to understand the safty of bridges crossing faulting zone. The different superstructures of bridges, simple beam and continuous beam will be discussed subsequently in simulations.

WE-AB-202-09: Feasibility and Quantitative Analysis of 4DCT-Based High Precision Lung Elastography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hasse, K; Neylon, J; Low, D

2016-06-15

Purpose: The purpose of this project is to derive high precision elastography measurements from 4DCT lung scans to facilitate the implementation of elastography in a radiotherapy context. Methods: 4DCT scans of the lungs were acquired, and breathing stages were subsequently registered to each other using an optical flow DIR algorithm. The displacement of each voxel gleaned from the registration was taken to be the ground-truth deformation. These vectors, along with the 4DCT source datasets, were used to generate a GPU-based biomechanical simulation that acted as a forward model to solve the inverse elasticity problem. The lung surface displacements were appliedmore » as boundary constraints for the model-guided lung tissue elastography, while the inner voxels were allowed to deform according to the linear elastic forces within the model. A biomechanically-based anisotropic convergence magnification technique was applied to the inner voxels in order to amplify the subtleties of the interior deformation. Solving the inverse elasticity problem was accomplished by modifying the tissue elasticity and iteratively deforming the biomechanical model. Convergence occurred when each voxel was within 0.5 mm of the ground-truth deformation and 1 kPa of the ground-truth elasticity distribution. To analyze the feasibility of the model-guided approach, we present the results for regions of low ventilation, specifically, the apex. Results: The maximum apical boundary expansion was observed to be between 2 and 6 mm. Simulating this expansion within an apical lung model, it was observed that 100% of voxels converged within 0.5 mm of ground-truth deformation, while 91.8% converged within 1 kPa of the ground-truth elasticity distribution. A mean elasticity error of 0.6 kPa illustrates the high precision of our technique. Conclusion: By utilizing 4DCT lung data coupled with a biomechanical model, high precision lung elastography can be accurately performed, even in low ventilation regions of the lungs. This material is based upon work supported by the National Science Foundation Graduate Research Fellowship under Grant No. DGE-1144087.« less

Quantitative assessment of soft tissue deformation using digital speckle pattern interferometry: studies on phantom breast models

PubMed Central

Karuppanan, Udayakumar; Unni, Sujatha Narayanan; Angarai, Ganesan R.

2017-01-01

Abstract. Assessment of mechanical properties of soft matter is a challenging task in a purely noninvasive and noncontact environment. As tissue mechanical properties play a vital role in determining tissue health status, such noninvasive methods offer great potential in framing large-scale medical screening strategies. The digital speckle pattern interferometry (DSPI)–based image capture and analysis system described here is capable of extracting the deformation information from a single acquired fringe pattern. Such a method of analysis would be required in the case of the highly dynamic nature of speckle patterns derived from soft tissues while applying mechanical compression. Soft phantoms mimicking breast tissue optical and mechanical properties were fabricated and tested in the DSPI out of plane configuration set up. Hilbert transform (HT)-based image analysis algorithm was developed to extract the phase and corresponding deformation of the sample from a single acquired fringe pattern. The experimental fringe contours were found to correlate with numerically simulated deformation patterns of the sample using Abaqus finite element analysis software. The extracted deformation from the experimental fringe pattern using the HT-based algorithm is compared with the deformation value obtained using numerical simulation under similar conditions of loading and the results are found to correlate with an average %error of 10. The proposed method is applied on breast phantoms fabricated with included subsurface anomaly mimicking cancerous tissue and the results are analyzed. PMID:28180134

Approximation solution of Schrodinger equation for Q-deformed Rosen-Morse using supersymmetry quantum mechanics (SUSY QM)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alemgadmi, Khaled I. K., E-mail: azozkied@yahoo.com; Suparmi; Cari

2015-09-30

The approximate analytical solution of Schrodinger equation for Q-Deformed Rosen-Morse potential was investigated using Supersymmetry Quantum Mechanics (SUSY QM) method. The approximate bound state energy is given in the closed form and the corresponding approximate wave function for arbitrary l-state given for ground state wave function. The first excited state obtained using upper operator and ground state wave function. The special case is given for the ground state in various number of q. The existence of Rosen-Morse potential reduce energy spectra of system. The larger value of q, the smaller energy spectra of system.

Importance of methodological standardization for the ektacytometric measures of red blood cell deformability in sickle cell anemia.

PubMed

Renoux, Céline; Parrow, Nermi; Faes, Camille; Joly, Philippe; Hardeman, Max; Tisdale, John; Levine, Mark; Garnier, Nathalie; Bertrand, Yves; Kebaili, Kamila; Cuzzubbo, Daniela; Cannas, Giovanna; Martin, Cyril; Connes, Philippe

2016-01-01

Red blood cell (RBC) deformability is severely decreased in patients with sickle cell anemia (SCA), which plays a role in the pathophysiology of the disease. However, investigation of RBC deformability from SCA patients demands careful methodological considerations. We assessed RBC deformability by ektacytometry (LORRCA MaxSis, Mechatronics, The Netherlands) in 6 healthy individuals and 49 SCA patients and tested the effects of different heights of the RBC diffraction patterns, obtained by altering the camera gain of the LORRCA, on the result of RBC deformability measurements, expressed as Elongation Index (EI). Results indicate that the pattern of RBCs from control subjects adopts an elliptical shape under shear stress, whereas the pattern of RBCs from individuals with SCA adopts a diamond shape arising from the superposition of elliptical and circular patterns. The latter represent rigid RBCs. While the EI measures did not change with the variations of the RBC diffraction pattern heights in the control subjects, we observed a decrease of EI when the RBC diffraction pattern height is increased in the SCA group. The differences in SCA EI values measured at 5 Pa between the different diffraction pattern heights correlated with the percent of hemoglobin S and the percent of sickled RBC observed by microscopy. Our study confirms that the camera gain or aperture of the ektacytometer should be used to standardize the size of the RBC diffraction pattern height when measuring RBC deformability in sickle cell patients and underscores the potential clinical utility of this technique.

Seismic Design of a Single Bored Tunnel: Longitudinal Deformations and Seismic Joints

NASA Astrophysics Data System (ADS)

Oh, J.; Moon, T.

2018-03-01

The large diameter bored tunnel passing through rock and alluvial deposits subjected to seismic loading is analyzed for estimating longitudinal deformations and member forces on the segmental tunnel liners. The project site has challenges including high hydrostatic pressure, variable ground profile and high seismic loading. To ensure the safety of segmental tunnel liner from the seismic demands, the performance-based two-level design earthquake approach, Functional Evaluation Earthquake and Safety Evaluation Earthquake, has been adopted. The longitudinal tunnel and ground response seismic analyses are performed using a three-dimensional quasi-static linear elastic and nonlinear elastic discrete beam-spring elements to represent segmental liner and ground spring, respectively. Three components (longitudinal, transverse and vertical) of free-field ground displacement-time histories evaluated from site response analyses considering wave passage effects have been applied at the end support of the strain-compatible ground springs. The result of the longitudinal seismic analyses suggests that seismic joint for the mitigation measure requiring the design deflection capacity of 5-7.5 cm is to be furnished at the transition zone between hard and soft ground condition where the maximum member forces on the segmental liner (i.e., axial, shear forces and bending moments) are induced. The paper illustrates how detailed numerical analyses can be practically applied to evaluate the axial and curvature deformations along the tunnel alignment under difficult ground conditions and to provide the seismic joints at proper locations to effectively reduce the seismic demands below the allowable levels.

Association of spinal deformity and pelvic tilt with gait asymmetry in adolescent idiopathic scoliosis patients: Investigation of ground reaction force.

PubMed

Park, Yang Sun; Lim, Young Tae; Koh, Kyung; Kim, Jong Moon; Kwon, Hyun Joon; Yang, Ji Seung; Shim, Jae Kun

2016-07-01

Adolescent idiopathic scoliosis is a prevalent orthopedic problem in children ages 10 to 16years. Although genetic, physiological and biomechanical factors are considered to contribute to the onset and progression of adolescent idiopathic scoliosis, the underlying mechanisms are not yet clear. The purpose of this study was to investigate the association between spinal deformity and inter-leg ground reaction force asymmetry during walking in adolescent idiopathic scoliosis patients. Fourteen patients (3 males and 11 females) participated in this study. Maximum Cobb's angle, adjusted Cobb's angle, and pelvic tilt were calculated from X-ray images. Asymmetry indices between legs were also calculated from ground reaction force magnitude and time variables from their preferred speed walking. Pearson coefficients of correlation were used to investigate associations of asymmetry indices with angle variables. Asymmetry indices of ground reaction force magnitudes positively correlated with adjusted Cobb's angle and maximum Cobb's angle mainly during the peak of braking phase, average of braking phase, while asymmetry indices of ground reaction force time variables showed no significant correlation with adjusted or maximum Cobb's angle. In contrast, asymmetry indices of ground reaction force time variables positively correlated with pelvic tilt during stance phase. We concluded that the spinal deformity of adolescent idiopathic scoliosis patients estimated using the maximum and adjusted Cobb's angles is generally associated with greater asymmetry of ground reaction force magnitudes in walking, while the pelvic tilt is associated with the greater asymmetry of ground reaction force time variables. Copyright © 2016 Elsevier Ltd. All rights reserved.

Online phase measuring profilometry for rectilinear moving object by image correction

NASA Astrophysics Data System (ADS)

Yuan, Han; Cao, Yi-Ping; Chen, Chen; Wang, Ya-Pin

2015-11-01

In phase measuring profilometry (PMP), the object must be static for point-to-point reconstruction with the captured deformed patterns. While the object is rectilinearly moving online, the size and pixel position differences of the object in different captured deformed patterns do not meet the point-to-point requirement. We propose an online PMP based on image correction to measure the three-dimensional shape of the rectilinear moving object. In the proposed method, the deformed patterns captured by a charge-coupled diode camera are reprojected from the oblique view to an aerial view first and then translated based on the feature points of the object. This method makes the object appear stationary in the deformed patterns. Experimental results show the feasibility and efficiency of the proposed method.

The 2010 slow slip event and secular motion at Kilauea, Hawai`i inferred from TerraSAR-X InSAR data

USGS Publications Warehouse

Chen, Jingyi; Zebker, Howard A.; Segall, Paul; Miklius, Asta

2014-01-01

We present here an Small BAseline Subset (SBAS) algorithm to extract both transient and secular ground deformations on the order of millimeters in the presence of tropospheric noise on the order of centimeters, when the transient is of short duration and known time, and the background deformation is smooth in time. We applied this algorithm to study the 2010 slow slip event as well as the secular motion of Kīlauea's south flank using 49 TerraSAR-X images. We also estimate the tropospheric delay variation relative to a given reference pixel using an InSAR SBAS approach. We compare the InSAR SBAS solution for both ground deformation and tropospheric delays with existing GPS measurements and confirm that the ground deformation signal andtropospheric noise in InSAR data are successfully separated. We observe that the coastal region on the south side of the Hilina Pali moves at a higher background rate than the region north side of the Pali. We also conclude that the 2010 SSE displacement is mainly horizontal and the maximum magnitude of the 2010 SSE vertical component is less than 5 mm.

Liquefaction, ground oscillation, and soil deformation at the Wildlife Array, California

USGS Publications Warehouse

Holzer, T.L.; Youd, T.L.

2007-01-01

Excess pore-water pressure and liquefaction at the Wildlife Liquefaction Array in 1987 were caused by deformation associated with both high-frequency strong ground motion and 5.5-second-period Love waves. The Love waves produced large (???1.5%) cyclic shear strains well after the stronger high-frequency ground motion abated. These cyclic strains generated approximately from 13 to 35% of the excess pore-water pressure in the liquefied layer and caused excess pore-water pressures ultimately to reach effective overburden stress. The deformation associated with the Love waves explains the "postearthquake" increase of pore-water pressure that was recorded at the array. This explanation suggests that conventional methods for predicting liquefaction based on peak ground acceleration are incomplete and may need to consider cyclic strains associated with long-period surface waves. A post-earthquake survey of an inclinometer casing indicated permanent shear strain associated with lateral spreading primarily occurred in the upper part of the liquefied layer. Comparison of cone penetration test soundings conducted after the earthquake with pre-earthquake soundings suggests sleeve friction increased. Natural lateral variability of the liquefied layer obscured changes in tip resistance despite a ???1% reduction in volume. The large oscillatory motion associated with surface waves explains ground oscillation that has been reported at some liquefaction sites during earthquakes.

Mount Etna InSAR Time Series Animation

NASA Image and Video Library

2012-02-06

This animation depicts a time-series of ground deformation at Mount Etna Volcano between 1992 and 2001. The deformation results from changes in the volume of a shallow chamber centered approximately 5 km 3 miles below sea level.

Correlation between pore fluid pressures and DInSAR post-seismic deformation of the May 20, 2012 Emilia-Romagna (Italy) earthquake

NASA Astrophysics Data System (ADS)

Moro, M.; Stramondo, S.; Albano, M.; Barba, S.; Solaro, G.; Saroli, M.; Bignami, C.

2015-12-01

The present work focuses on the detection and analysis of the postseismic surface deformations following the two earthquakes that hit the Emilia Romagna region (Italy) on May 20 and 29, 2012. The 2012 Emilia earthquake sequence struck the central sector of the Ferrara arc, which represents the external fold-and-thrust system of the Northern Apennines thrust belt buried below the Po plain. The May 20 event occurred on the Ferrara basal thrust at depth, at about 6-7 km, while, during the May 29 event, the rupture jumped on an inner splay of the Ferrara system. The analysis of the postseismic displacements was carried out thanks to a dataset of SAR COSMO­ SkyMed images covering a time span of about one year (May 20, 2012 - May 11, 2013) after the May 20 event. The DInSAR results revealed the presence of two deformation patches: the first one is located in the area that experienced the coseismic uplift. Here the postseismic displacements point out a further ground uplift occurring along the first three months after the 20 May event. The second deformation patch is located in the villages of San Carlo and Mirabello, where ground subsidence lasting about four months was detected. We hypothesized that both the observed phenomena are related to the pore pressure perturbation caused by the coseismic deformation. In particular, the ground uplift is due to the deep crustal deformations caused by the pore fluid diffusion at depth to re-establish the initial hydrostatic stresses. Instead, the ground subsidence is related to the compaction of the shallow sandy layers caused by the liquefaction phenomena, which widely affected the San Carlo and Mirabello area. Preliminary numerical analyses performed with the Finite Element Method and empirical relations confirmed our hypothesis.

Recent Surface Deformation in the Himalaya and Adjoining Piedmont Zone of the Ganga Plain, Uttarakhand, India

NASA Astrophysics Data System (ADS)

Chang, C. P.

2015-12-01

The Himalaya Frontal Thrust (HFT) is the longest active contractional structure on Earth. Understanding the activity of HFT and its surrounding area is a key for both unraveling the mechanism of Himalayan growth and preparing the major earthquake disasters. The latter issue became much more important after the April 25th 2015 Nepal earthquake (also known as the Gorkha earthquake), which killed more than 8,800 people and injured more than 23,000. This earthquake is a dramatic manifestation of the ongoing convergence between the Indo-Australian and Asian tectonic plates that has progressively built the Himalayas over the last 50 million years. Despite its importance, only a few preliminary studies have focused on the frontal part of the western Himalaya. The Himalaya and adjoining Ganga (also called Gangetic) plain in Uttarakhand state of India are traversed by a number of neotectonically active longitudinal and transverse faults. However, the pattern and extent of present day surface deformations caused by these faults is not yet well known. We herein present the preliminary results of our investigation directed in this direction. Surface deformations induced by active faults during a period of seven years from 2003 to 2010 in the south western Himalaya and adjoining proximal part of the Ganga Plain in Uttarakhand state of India have been firstly monitored. Multidate ENVISAT radar images of the area have been analyzed by applying the latest radar remote sensing technique of Persistent Scatterers Interferometric Synthetic Aperture Radar (PSI). Since PSI can extracts surface information even on vegetated or mountainous regions as well. The study reveals some conspicuous surface deformation patterns, which may be related directly to the active movements along some of the major fault /thrust in the area. For example the HFT and the transverse Garampani-Kathgodam Fault (G-KF). A campaign GPS network of 20 stations has also been installed in 2013 in our study area. This network also provided us important ground data to proof and adjust our PSI measurement and can help us better understanding the present deformation behavior of this area.

Investigation of Optimal Digital Image Correlation Patterns for Deformation Measurement

NASA Technical Reports Server (NTRS)

Bomarito, G. F.; Ruggles, T. J.; Hochhalter, J. D.; Cannon, A. H.

2016-01-01

Digital image correlation (DIC) relies on the surface texture of a specimen to measure deformation. When the specimen itself has little or no texture, a pattern is applied to the surface which deforms with the specimen and acts as an artificial surface texture. Because the applied pattern has an effect on the accuracy of DIC, an ideal pattern is sought for which the error introduced into DIC measurements is minimal. In this work, a study is performed in which several DIC pattern quality metrics from the literature are correlated to DIC measurement error. The resulting correlations give insight on the optimality of DIC patterns in general. Optimizations are then performed to produce patterns which are well suited for DIC. These patterns are tested to show their relative benefits. Chief among these benefits are a reduction in error of approximately 30 with respect to a randomly generated pattern.

Izmit, Turkey 1999 Earthquake Interferogram

NASA Image and Video Library

2001-03-30

This image is an interferogram that was created using pairs of images taken by Synthetic Aperture Radar (SAR). The images, acquired at two different times, have been combined to measure surface deformation or changes that may have occurred during the time between data acquisition. The images were collected by the European Space Agency's Remote Sensing satellite (ERS-2) on 13 August 1999 and 17 September 1999 and were combined to produce these image maps of the apparent surface deformation, or changes, during and after the 17 August 1999 Izmit, Turkey earthquake. This magnitude 7.6 earthquake was the largest in 60 years in Turkey and caused extensive damage and loss of life. Each of the color contours of the interferogram represents 28 mm (1.1 inches) of motion towards the satellite, or about 70 mm (2.8 inches) of horizontal motion. White areas are outside the SAR image or water of seas and lakes. The North Anatolian Fault that broke during the Izmit earthquake moved more than 2.5 meters (8.1 feet) to produce the pattern measured by the interferogram. Thin red lines show the locations of fault breaks mapped on the surface. The SAR interferogram shows that the deformation and fault slip extended west of the surface faults, underneath the Gulf of Izmit. Thick black lines mark the fault rupture inferred from the SAR data. Scientists are using the SAR interferometry along with other data collected on the ground to estimate the pattern of slip that occurred during the Izmit earthquake. This then used to improve computer models that predict how this deformation transferred stress to other faults and to the continuation of the North Anatolian Fault, which extends to the west past the large city of Istanbul. These models show that the Izmit earthquake further increased the already high probability of a major earthquake near Istanbul. http://photojournal.jpl.nasa.gov/catalog/PIA00557

Izmit, Turkey 1999 Earthquake Interferogram

NASA Technical Reports Server (NTRS)

2001-01-01

This image is an interferogram that was created using pairs of images taken by Synthetic Aperture Radar (SAR). The images, acquired at two different times, have been combined to measure surface deformation or changes that may have occurred during the time between data acquisition. The images were collected by the European Space Agency's Remote Sensing satellite (ERS-2) on 13 August 1999 and 17 September 1999 and were combined to produce these image maps of the apparent surface deformation, or changes, during and after the 17 August 1999 Izmit, Turkey earthquake. This magnitude 7.6 earthquake was the largest in 60 years in Turkey and caused extensive damage and loss of life. Each of the color contours of the interferogram represents 28 mm (1.1 inches) of motion towards the satellite, or about 70 mm (2.8 inches) of horizontal motion. White areas are outside the SAR image or water of seas and lakes. The North Anatolian Fault that broke during the Izmit earthquake moved more than 2.5 meters (8.1 feet) to produce the pattern measured by the interferogram. Thin red lines show the locations of fault breaks mapped on the surface. The SAR interferogram shows that the deformation and fault slip extended west of the surface faults, underneath the Gulf of Izmit. Thick black lines mark the fault rupture inferred from the SAR data. Scientists are using the SAR interferometry along with other data collected on the ground to estimate the pattern of slip that occurred during the Izmit earthquake. This then used to improve computer models that predict how this deformation transferred stress to other faults and to the continuation of the North Anatolian Fault, which extends to the west past the large city of Istanbul. These models show that the Izmit earthquake further increased the already high probability of a major earthquake near Istanbul.

The 1969–1985 Pozzuoli event and active volcanisms

PubMed Central

Yokoyama, Izumi

2006-01-01

Pozzuoli is located at the center of the Campi Flegrei caldera, near Naples and is famous for its anomalous subsidence and upheaval documented since the Roman period. Its secular and gradual subsidence can be interpreted as self-loading compaction of the caldera fills while abrupt upheavals are geologically suspected to be caused by magmagenic movements or steam forces. In order to interpret the origin and the process of the Pozzuoli upheavals, they are compared with active volcanisms represented by the 1977–1982 eruption of Usu volcano in Hokkaido. Usu volcano outburst in 1977 in major pumice eruptions and repeated magmatic and phreatomagmatic eruptions, and manifested remarkable ground deformations accompanying earthquake swarms. In 1969, the ground of Pozzuoli began to upheave with increases in seismicity but finally failed to cause any eruptive phenomena at the surface; nevertheless there are common characteristics of their motives and processes between the two events. The motive of the Usu deformation is clearly due to magma movements while that of the Pozzuoli upheaval has not been completely settled. A quantitative relationship between seismicity and deformation gives a clue for discussing the motive of the Pozzuoli deformations. The discharge rates of seismic energy and the deformation rates are compared between the two events and a certain similarity is found. This suggests that the origin of the Pozzuoli event may be partly magmatic as well as the Usu eruption, but its behavior largely depends on the property of the caldera deposits. When their deformation volumes are taken into consideration, their characteristics become quantitatively conspicuous. The ground at Pozzuoli is much more easily deformed by the upward motive force than Usu volcano. This is due to the rheological property of the caldera deposits of Campi Flegrei, and agrees to the theory that interprets the secular subsidence observed in historical times, as self-loading compaction. It is interesting that there is a point of contact between anomalous movements of the ground along the seashore in Italy and remarkable magmatic movements at the active volcano in Japan. PMID:25873752

Using Ground Radar Interferometry for Precise Determining of Deformation and Vertical Deflection of Structures

NASA Astrophysics Data System (ADS)

Talich, Milan

2017-12-01

The paper describes possibilities of the relatively new technics - ground based radar interferometry for precise determining of deformation of structures. Special focus on the vertical deflection of bridge structures and on the horizontal movements of high-rise buildings and structural objects is presented. The technology of ground based radar interferometry can be used in practice to the contactless determination of deformations of structures with accuracy up to 0.01 mm in real time. It is also possible in real time to capture oscillations of the object with a frequency up to 50 Hz. Deformations can be determined simultaneously in multiple places of the object, for example a bridge structure at points distributed on the bridge deck at intervals of one or more meters. This allows to obtain both overall and detailed information about the properties of the structure during the dynamic load and monitoring the impact of movements either individual vehicles or groups. In the case of high-rise buildings, it is possible to monitor the horizontal vibration of the whole object at its different height levels. It is possible to detect and determine the compound oscillations that occur in some types of buildings. Then prevent any damage or even disasters in these objects. In addition to the necessary theory basic principles of using radar interferometry for determining of deformation of structures are given. Practical examples of determining deformation of bridge structures, water towers reservoirs, factory chimneys and wind power plants are also given. The IBIS-S interferometric radar of the Italian IDS manufacturer was used for the measurements.

Deformation field correction for spatial normalization of PET images

PubMed Central

Bilgel, Murat; Carass, Aaron; Resnick, Susan M.; Wong, Dean F.; Prince, Jerry L.

2015-01-01

Spatial normalization of positron emission tomography (PET) images is essential for population studies, yet the current state of the art in PET-to-PET registration is limited to the application of conventional deformable registration methods that were developed for structural images. A method is presented for the spatial normalization of PET images that improves their anatomical alignment over the state of the art. The approach works by correcting the deformable registration result using a model that is learned from training data having both PET and structural images. In particular, viewing the structural registration of training data as ground truth, correction factors are learned by using a generalized ridge regression at each voxel given the PET intensities and voxel locations in a population-based PET template. The trained model can then be used to obtain more accurate registration of PET images to the PET template without the use of a structural image. A cross validation evaluation on 79 subjects shows that the proposed method yields more accurate alignment of the PET images compared to deformable PET-to-PET registration as revealed by 1) a visual examination of the deformed images, 2) a smaller error in the deformation fields, and 3) a greater overlap of the deformed anatomical labels with ground truth segmentations. PMID:26142272

Analysis of building deformation in landslide area using multisensor PSInSAR™ technique.

PubMed

Ciampalini, Andrea; Bardi, Federica; Bianchini, Silvia; Frodella, William; Del Ventisette, Chiara; Moretti, Sandro; Casagli, Nicola

2014-12-01

Buildings are sensitive to movements caused by ground deformation. The mapping both of spatial and temporal distribution, and of the degree of building damages represents a useful tool in order to understand the landslide evolution, magnitude and stress distribution. The high spatial resolution of space-borne SAR interferometry can be used to monitor displacements related to building deformations. In particular, PSInSAR technique is used to map and monitor ground deformation with millimeter accuracy. The usefulness of the above mentioned methods was evaluated in San Fratello municipality (Sicily, Italy), which was historically affected by landslides: the most recent one occurred on 14th February 2010. PSInSAR data collected by ERS 1/2, ENVISAT, RADARSAT-1 were used to study the building deformation velocities before the 2010 landslide. The X-band sensors COSMO-SkyMed and TerraSAR-X were used in order to monitor the building deformation after this event. During 2013, after accurate field inspection on buildings and structures, damage assessment map of San Fratello were created and then compared to the building deformation velocity maps. The most interesting results were obtained by the comparison between the building deformation velocity map obtained through COSMO-SkyMed and the damage assessment map. This approach can be profitably used by local and Civil Protection Authorities to manage the post-event phase and evaluate the residual risks.

Characterizing Englacial Attenuation and Grounding Zone Geometry Using Airborne Radar Sounding

NASA Astrophysics Data System (ADS)

Schroeder, D. M.; Grima, C.; Blankenship, D. D.

2014-12-01

The impact of warm ocean water on ice sheet retreat and stability is a one of the primary drivers and sources of uncertainty for the rate of global sea level rise. One critical but challenging observation required to understand and model this impact is the location and extent of grounding ice sheet zones. However, existing surface topography based techniques do not directly detect the location where ocean water reaches (or breaches) grounded ice at the bed, which can significantly affect ice sheet stability. The primary geophysical tool for directly observing the basal properties of ice sheets is airborne radar sounding. However, uncertainty in englacial attenuation from unknown ice temperature and chemistry can lead to erroneous interpretation of subglacial conditions from bed echo strengths alone . Recently developed analysis techniques for radar sounding data have overcome this challenge by taking advantage of information in the angular distribution of bed echo energy and joint modeling of radar returns and water routing. We have developed similar approaches to analyze the spatial pattern and character of echoes to address the problems of improved characterization of grounding zone geometry and englacial attenuation. The spatial signal of the transition from an ice-bed interface to an ice-ocean interface is an increase in bed echo strength. However, rapidly changing attenuation near the grounding zone prevents the unambiguous interpretation of this signal in typical echo strength profiles and violates the assumptions of existing empirical attenuation correction techniques. We present a technique that treat bed echoes as continuous signals to take advantage of along-profile ice thickness and echo strength variations to constrain the spatial pattern of attenuation and detect the grounding zone transition. The transition from an ice-bed interface to an ice-ocean interface will also result in a change in the processes that determine basal interface morphology (e.g. melt/freeze processes for floating ice vs. erosion/deformation processes for grounded ice). This morphology change will be expressed in the angular distribution and coherency of bed echo energy. We also present techniques that exploit this character of bed echoes to further improve the detection and characterization of grounding zones.

Infrasonic wave accompanying a crack opening during the 2015 Hakone eruption

NASA Astrophysics Data System (ADS)

Yukutake, Yohei; Ichihara, Mie; Honda, Ryou

2018-03-01

To understand the initial process of the phreatic eruption of the Hakone volcano from June 29 to July 01, 2015, we analyzed infrasound data using the cross-correlation between infrasound and vertical ground velocity and compared the results of our analysis to the crustal deformation detected by tiltmeters and broadband seismometers. An infrasound signal and vertical ground motion due to an infrasound wave coupled to the ground were detected simultaneously with the opening of a crack source beneath the Owakudani geothermal region during the 2-min time period after 07:32 JST on June 29, 2015 (JST = UTC + 8 h). Given that the upper end of the open crack was approximately 150 m beneath the surface, the time for the direct emission of highly pressurized fluid from the upper end of the open crack to the surface should have exceeded the duration of the inflation owing to the hydraulic diffusivity in the porous media. Therefore, the infrasound signal coincident with the opening of the crack may reflect a sudden emission of volcanic gas resulting from the rapid vaporization of pre-existing groundwater beneath Owakudani because of the transfer of the volumetric strain change from the deformation source. We also noticed a correlation pattern corresponding to discrete impulsive infrasound signals during vent formation, which occurred several hours to 2 days after the opening of the crack. In particular, we noted that the sudden emission of vapor coincided with the inflation of the shallow pressure source, whereas the eruptive burst events accompanied by the largest vent formation were delayed by approximately 2 days. Furthermore, we demonstrated that the correlation method is a useful tool in detecting small infrasound signals and provides important information regarding the initial processes of the eruption.[Figure not available: see fulltext.

The Monitoring Case of Ground-Based Synthetic Aperture Radar with Frequency Modulated Continuous Wave System

NASA Astrophysics Data System (ADS)

Zhang, H. Y.; Zhai, Q. P.; Chen, L.; Liu, Y. J.; Zhou, K. Q.; Wang, Y. S.; Dou, Y. D.

2017-09-01

The features of the landslide geological disaster are wide distribution, variety, high frequency, high intensity, destructive and so on. It has become a natural disaster with harmful and wide range of influence. The technology of ground-based synthetic aperture radar is a novel deformation monitoring technology developed in recent years. The features of the technology are large monitoring area, high accuracy, long distance without contact and so on. In this paper, fast ground-based synthetic aperture radar (Fast-GBSAR) based on frequency modulated continuous wave (FMCW) system is used to collect the data of Ma Liuzui landslide in Chongqing. The device can reduce the atmospheric errors caused by rapidly changing environment. The landslide deformation can be monitored in severe weather conditions (for example, fog) by Fast-GBSAR with acquisition speed up to 5 seconds per time. The data of Ma Liuzui landslide in Chongqing are analyzed in this paper. The result verifies that the device can monitor landslide deformation under severe weather conditions.

Research on filling scheme and deformation properties of wide subgrade of foamed lightweight soil on soft ground

NASA Astrophysics Data System (ADS)

Zhang, Faru; Yang, Deguang; Zhang, Liujun

2018-01-01

The wide subgrade on soft soil ground has the significantly different transverse settlement curve characteristics and the lacation of the maximum asymmetrical transverse settlement compared with ordinary subgrade. Especially when the subgrade filled with materials of different densities, the synergism deformation of ground-subgrade-pavement and the pavement structure stress become more complex. Combining with the engineering example, the settlement deformation characteristics of wide subgrade adopting the different filling scheme and the stress distribution of pavement structure are analyzed. Results show that the settlement curve of wide subgrade has a shape of flat middle with steep sides, and the maximum transverse asymmetrical settlement locates in close to the shoulder position. The maximum stress within the pavement structure is also in close to the shoulder position. Regarding the wide subgrade composed of main road and relief road, the post-construction settlement can be greatly reduced when both roads are filled with foamed lightweight soil.

Ground Surface Deformation in Unconsolidated Sediments Caused by Bedrock Fault Movements: Dip-Slip and Strike-Slip Fault Model Test and Field Survey

NASA Astrophysics Data System (ADS)

Ueta, K.; Tani, K.

2001-12-01

Sandbox experiments were performed to investigate ground surface deformation in unconsolidated sediments caused by dip-slip and strike-slip motion on bedrock faults. A 332.5 cm long, 200 cm high, and 40 cm wide sandbox was used in a dip-slip fault model test. In the strike-slip fault test, a 600 cm long, 250 cm wide, and 60 cm high sandbox and a 170 cm long, 25 cm wide, 15 cm high sandbox were used. Computerized X-ray tomography applied to the sandbox experiments made it possible to analyze the kinematic evolution, as well as the three-dimensional geometry, of the faults. The fault type, fault dip, fault displacement, thickness and density of sandpack and grain size of the sand were varied for different experiments. Field survey of active faults in Japan and California were also made to investigate the deformation of unconsolidated sediments overlying bedrock faults. A comparison of the experimental results with natural cases of active faults reveals the following: (1) In the case of dip-slip faulting, the shear bands are not shown as one linear plane but as en echelon pattern. Thicker and finer unconsolidated sediments produce more shear bands and clearer en echelon shear band patterns. (2) In the case of left-lateral strike-slip faulting, the deformation of the sand pack with increasing basement displacement is observed as follows. a) In three dimensions, the right-stepping shears that have a "cirque" / "shell" / "ship body" shape develop on both sides of the basement fault. The shears on one side of the basement fault join those on the other side, resulting in helicoidal shaped shear surfaces. Shears reach the surface of the sand near or above the basement fault and en echelon Riedel shears are observed at the surface of the sand. b) Right-stepping pressure ridges develop within the zone defined by the Riedel shears. c) Lower-angle shears generally branch off from the first Riedel shears. d) Right-stepping helicoidal shaped lower-angle shears offset Riedel shears and pressure ridges, and left-stepping and right-stepping pressure ridges are observed. d) With displacement concentrated on the central throughgoing fault zone, a "Zone of shear band" (ZSB) developed directly above the basement fault. The geometry of the ZSB shows a strong resemblance to linear ridge and trough geomorphology associated with active strike-slip faulting. (3) In the case of normal faulting, the location of the surface fault rupture is just above the bedrock faults, which have no relationship with the fault dip. On the other hand, the location of the surface rupture of the reverse fault has closely relationship with the fault dip. In the case of strike-slip faulting, the width of the deformation zone in dense sand is wider than that in loose sand. (4) The horizontal distance of surface rupture from the bedrock fault normalized by the height of sand mass (W/H) does not depend on the height of sand mass and grain size of sand. The values of W/H from the test agree well with those of earthquake faults. (5) The normalized base displacement required to propagate the shear rupture zone to the ground surface (D/H), in the case of normal faulting, is lower than those for reverse faulting and strike-slip faulting.

Monitoring and characterizing natural hazards with satellite InSAR imagery

USGS Publications Warehouse

Lu, Zhong; Zhang, Jixian; Zhang, Yonghong; Dzurisin, Daniel

2010-01-01

Interferometric synthetic aperture radar (InSAR) provides an all-weather imaging capability for measuring ground-surface deformation and inferring changes in land surface characteristics. InSAR enables scientists to monitor and characterize hazards posed by volcanic, seismic, and hydrogeologic processes, by landslides and wildfires, and by human activities such as mining and fluid extraction or injection. Measuring how a volcano’s surface deforms before, during, and after eruptions provides essential information about magma dynamics and a basis for mitigating volcanic hazards. Measuring spatial and temporal patterns of surface deformation in seismically active regions is extraordinarily useful for understanding rupture dynamics and estimating seismic risks. Measuring how landslides develop and activate is a prerequisite to minimizing associated hazards. Mapping surface subsidence or uplift related to extraction or injection of fluids during exploitation of groundwater aquifers or petroleum reservoirs provides fundamental data on aquifer or reservoir properties and improves our ability to mitigate undesired consequences. Monitoring dynamic water-level changes in wetlands improves hydrological modeling predictions and the assessment of future flood impacts. In addition, InSAR imagery can provide near-real-time estimates of fire scar extents and fire severity for wildfire management and control. All-weather satellite radar imagery is critical for studying various natural processes and is playing an increasingly important role in understanding and forecasting natural hazards.

Full-physics 3D heterogeneous simulations of electromagnetic induction fields on level and deformed sea ice

DOE Office of Scientific and Technical Information (OSTI.GOV)

Samluk, Jesse P.; Geiger, Cathleen A.; Weiss, Chester J.

In this article we explore simulated responses of electromagnetic (EM) signals relative to in situ field surveys and quantify the effects that different values of conductivity in sea ice have on the EM fields. We compute EM responses of ice types with a three-dimensional (3-D) finite-volume discretization of Maxwell's equations and present 2-D sliced visualizations of their associated EM fields at discrete frequencies. Several interesting observations result: First, since the simulator computes the fields everywhere, each gridcell acts as a receiver within the model volume, and captures the complete, coupled interactions between air, snow, sea ice and sea water asmore » a function of their conductivity; second, visualizations demonstrate how 1-D approximations near deformed ice features are violated. But the most important new finding is that changes in conductivity affect EM field response by modifying the magnitude and spatial patterns (i.e. footprint size and shape) of current density and magnetic fields. These effects are demonstrated through a visual feature we define as 'null lines'. Null line shape is affected by changes in conductivity near material boundaries as well as transmitter location. Our results encourage the use of null lines as a planning tool for better ground-truth field measurements near deformed ice types.« less

Full-physics 3D heterogeneous simulations of electromagnetic induction fields on level and deformed sea ice

DOE PAGES

Samluk, Jesse P.; Geiger, Cathleen A.; Weiss, Chester J.; ...

2015-10-01

In this article we explore simulated responses of electromagnetic (EM) signals relative to in situ field surveys and quantify the effects that different values of conductivity in sea ice have on the EM fields. We compute EM responses of ice types with a three-dimensional (3-D) finite-volume discretization of Maxwell's equations and present 2-D sliced visualizations of their associated EM fields at discrete frequencies. Several interesting observations result: First, since the simulator computes the fields everywhere, each gridcell acts as a receiver within the model volume, and captures the complete, coupled interactions between air, snow, sea ice and sea water asmore » a function of their conductivity; second, visualizations demonstrate how 1-D approximations near deformed ice features are violated. But the most important new finding is that changes in conductivity affect EM field response by modifying the magnitude and spatial patterns (i.e. footprint size and shape) of current density and magnetic fields. These effects are demonstrated through a visual feature we define as 'null lines'. Null line shape is affected by changes in conductivity near material boundaries as well as transmitter location. Our results encourage the use of null lines as a planning tool for better ground-truth field measurements near deformed ice types.« less

ASAR images a diverse set of deformation patterns at Kilauea volcano, Hawai'i

USGS Publications Warehouse

Poland, Michael P.

2007-01-01

Since 2003, 27 independent look angles have been acquired by ENVISAT’s Advanced Synthetic Aperture Radar (ASAR) instrument over the island of Hawai`i, allowing for the formation of thousands of interferograms showing deformation of the ground surface. On Kīlauea volcano, a transition from minor to broad-scale summit inflation was observed by interferograms that span 2003 to 2006. In addition, radar interferometry (InSAR) observations of Kīlauea led to the discovery of several previously unknown areas of localized subsidence in the caldera and along the volcano’s east rift zone. These features are probably caused by the cooling and contraction of accumulated lavas. After November 2005, a surface instability near the point that lava entered the ocean on the south flank of Kīlauea was observed in interferograms. The motion is most likely a result of unbuttressing of a portion of the coast following the collapse of a large lava delta in November 2005. InSAR data can also be used to map lava flow development over time, providing ~30 m spatial resolution maps at approximately monthly intervals. Future applications of InSAR to Kīlauea will probably result in more discoveries and insights, both as the style of volcano deformation changes and as data from new instruments are acquired.

In situ experimental assessment of lake whitefish development following a freshwater oil spill.

PubMed

Debruyn, Adrian M H; Wernick, Barbara G; Stefura, Corey; McDonald, Blair G; Rudolph, Barri-Lynn; Patterson, Luanne; Chapman, Peter M

2007-10-15

Wabamun Lake (Alberta, Canada) has been subject to ongoing contamination with polycyclic aromatic hydrocarbons (PAHs) from multiple sources for decades and in August 2005 was exposed to ca. 149 500 L of bunker C oil following a train derailment. We compared the pattern, frequency, and severity of deformity in larvae of lake whitefish (Coregonus clupeaformis) incubated in situ in areas of Wabamun Lake exposed only to "background" PAH contamination and in areas additionally exposed to PAHs from the oil. All sites in the lake (including reference areas) showed incidences of deformity higher than are typically observed in laboratory studies. A small number of oil-exposed sites showed higher incidences of some teratogenic deformities and a tendency to exhibit deformities of higher severity than sites not exposed to oil. The frequency of moderate to severe deformities in 8 of 16 classes was correlated with PAH exposure. Nonmetric multivariate ordination of deformity data revealed a general pattern of increasing incidence and severity of several skeletal (lordosis, scoliosis) and craniofacial (ocular, jaw) deformities at sites with relatively high exposure to oil-derived PAHs. A simultaneous consideration of incidence, severity, and pattern of deformity enabled us to detect a consistent (overall approximately 5% above background) response to the oil despite high variability and high background deformity rates in this historically contaminated environment.

First detection of precursory ground inflation of a small phreatic eruption by InSAR

NASA Astrophysics Data System (ADS)

Kobayashi, Tomokazu; Morishita, Yu; Munekane, Hiroshi

2018-06-01

Phreatic eruptions are caused by pressurization of geothermal fluid sources at shallow levels. They are relatively small compared to typical magmatic eruptions, but can be very hazardous. However, owing to their small magnitudes, their occurrences are difficult to predict. Here we show the detection of locally distributed ground inflation preceding a small phreatic eruption at the Hakone volcano, Japan, through the application of interferometric synthetic aperture radar analysis. The ground inflation proceeded the eruption at slow speed of ∼5 mm/month with a spatial size of ∼200 m in the early stage, and then it accelerated 2 months before the eruption that occurred for the first time in 800-900 yrs. The ground uplift reached ∼30 cm, and the eruption occurred nearby the most deformed part. The deformation speed correlated well with inflation of spherical source located at 4.8 km below sea level, thus suggesting that heat and/or volcanic fluid supply from the spherical source, maybe magma reservoir, directly drove the subsurface hydrothermal activity. Our results demonstrate that high-spatial-resolution deformation data can be a good indicator of subsurface pressure conditions with pinpoint spatial accuracy during the preparatory process of phreatic eruptions.

Occurrence of oral deformities in larval anurans

USGS Publications Warehouse

Drake, D.L.; Altig, R.; Grace, J.B.; Walls, S.C.

2007-01-01

We quantified deformities in the marginal papillae, tooth rows, and jaw sheaths of tadpoles from 13 population samples representing three families and 11 sites in the southeastern United States. Oral deformities were observed in all samples and in 13.5-98% of the specimens per sample. Batrachochytrium dendrobatidis (chytrid) infections were detected in three samples. There was high variability among samples in the pattern and number of discovered deformities. Pairwise associations between oral structures containing deformities were nonrandom for several populations, especially those with B. dendrobatidis infections or high total numbers of deformities. Comparisons of deformities among samples using multivariate analyses revealed that tadpole samples grouped together by family. Analyses of ordination indicated that three variables, the number of deformities, the number of significant associations among deformity types within populations, and whether populations were infected with B. dendrobatidis, were significantly correlated with the pattern of deformities. Our data indicate that the incidence of oral deformities can be high in natural populations and that phylogeny and B. dendrobatidis infection exert a strong influence on the occurrence and type of oral deformities in tadpoles. ?? by the American Society of Ichthyologists and Herperologists.

Interferometric synthetic aperture radar: Building tomorrow's tools today

USGS Publications Warehouse

Lu, Zhong

2006-01-01

A synthetic aperture radar (SAR) system transmits electromagnetic (EM) waves at a wavelength that can range from a few millimeters to tens of centimeters. The radar wave propagates through the atmosphere and interacts with the Earth’s surface. Part of the energy is reflected back to the SAR system and recorded. Using a sophisticated image processing technique, called SAR processing (Curlander and McDonough, 1991), both the intensity and phase of the reflected (or backscattered) signal of each ground resolution element (a few meters to tens of meters) can be calculated in the form of a complex-valued SAR image representing the reflectivity of the ground surface. The amplitude or intensity of the SAR image is determined primarily by terrain slope, surface roughness, and dielectric constants, whereas the phase of the SAR image is determined primarily by the distance between the satellite antenna and the ground targets, slowing of the signal by the atmosphere, and the interaction of EM waves with ground surface. Interferometric SAR (InSAR) imaging, a recently developed remote sensing technique, utilizes the interaction of EM waves, referred to as interference, to measure precise distances. Very simply, InSAR involves the use of two or more SAR images of the same area to extract landscape topography and its deformation patterns.

Estimation of Static Coulomb Stress Change and Strong Motion Simulation for Jiuzhaigou 7.0 Earthquake Base on SENTINEL-1 Insar Data Inversion

NASA Astrophysics Data System (ADS)

Shen, W. H.; Luo, Y.; Jiao, Q. S.

2018-04-01

On August 8, 2017, an earthquake of M 7.0 occurred at Jiuzhaigou. Based on the Sentinel-1 satellite InSAR data, we obtained coseismic deformation field and inverted the source slip model. Results show that this event is dominated by strike slip, and the total released seismic moment is 8.06 × 1018 Nm, equivalent to an earthquake of Mw 6.57. We calculated static stress changes along strike and dip direction, and the static stress analysis show that the average stress drop are at low level, which may be responsible for the low level of ground motion during Jiuzhaigou earthquake. The coseismic Coulomb stress changes are calculated base on the inverted slip model, which revealed that 82.59 % of aftershocks are located in the Coulomb stress increasing area, 78.42 % of total aftershocks may be triggered by the mainshock aftershock, indicating that the mainshock has a significant triggering effect on the subsequent aftershocks. Based on stochastic finite fault model, we simulated regional peak ground acceleration (PGA), peak ground velocity (PGV) and the intensity, and results could capture basic features associated with the ground motion patterns. Moreover, the simulated results reflect the obvious rupture directivity effect.

Typhoon-Induced Ground Deformation

NASA Astrophysics Data System (ADS)

Mouyen, M.; Canitano, A.; Chao, B. F.; Hsu, Y.-J.; Steer, P.; Longuevergne, L.; Boy, J.-P.

2017-11-01

Geodetic instruments now offer compelling sensitivity, allowing to investigate how solid Earth and surface processes interact. By combining surface air pressure data, nontidal sea level variations model, and rainfall data, we systematically analyze the volumetric deformation of the shallow crust at seven borehole strainmeters in Taiwan induced by 31 tropical cyclones (typhoons) that made landfall to the island from 2004 to 2013. The typhoon's signature consists in a ground dilatation due to air pressure drop, generally followed by a larger ground compression. We show that this compression phase can be mostly explained by the mass loading of rainwater that falls on the ground and concentrates in the valleys towards the strainmeter sensitivity zone. Further, our analysis shows that borehole strainmeters can help quantifying the amount of rainwater accumulating and flowing over a watershed during heavy rainfalls, which is a useful constraint for building hydrological models.

Potentials and Limits of Sar Permanent Scatterers In Ground Deformation Monitoring

NASA Astrophysics Data System (ADS)

Rocca, F.; Colesanti, C.; Ferretti, A.; Prati, C.

The Permanent Scatterers (PS) technique allows the identification of individual radar targets particularly suitable for SAR interferometric measurements. In fact, despite its remarkable potential, spaceborne SAR Differential Interferometry (DInSAR) has not been fully exploited as a reference tool for ground deformation mapping, due to the presence of atmospheric artefacts as well as geometrical and temporal phase decorrelation. Both drawbacks are overcome in a multi-image framework of interfer- ometric data (>25-30 images) jointly used in order to properly identify and exploit the subset of image pixels corresponding to privileged reflectors, the so-called Per- manent Scatterers. Provided that at least 3-4 PS/sqkm are available, accurate phase measurements carried out on the sparse PS grid allow one to compensate data for the atmospheric phase contributions. Average ground deformation rate as well as full dis- placement time series (both along the satellite Line of Sight, LOS) are estimated with millimetric accuracy on individual PS locations. The PS subset of image pixels can be thought of as a high density (100-400 PS/sqkm, in urban areas) "natural" geode- tic network. This study aims at discussing in detail potentials and limits of the PS approach in monitoring ground deformation phenomena characterised by a complex time non-uniform evolution (Non-Linear Motion, NLM). PS results highlighting sea- sonal displacement effects beneath San Jose (Santa Clara Valley, California) are going to be discussed. The deformation occurring there is related to the seasonal variation of the ground water level in the area delimited by the Silver Creek and the San Jose fault. The San Jose PS analysis is exploited as a significant case study to assess the main requirements for a successful detection of NLM phenomena (by means of PS), and to analyse their impact on the quality of results. Particular attention will be de- voted to the effect of irregularly sampled data and missing acquisitions. The strategies used in order to isolate the phase contribution relative to time non-uniform displace- ment phenomena from other phase terms (mainly atmospheric artefacts and residual topography) are going to be illustrated. Moreover, the main aspects to be considered envisaging a synergistic use of PS results and both GPS and optical levelling data are going to be outlined. Finally, attention will be paid to key issues to be taken into account for designing future SAR missions dedicated to detection and monitoring of ground deformation phenomena.

Monitoring Ground Deformation at the Aquistore CO2 Storage Site in SE Saskatchewan, Canada

NASA Astrophysics Data System (ADS)

Samsonov, S. V.; White, D.; Craymer, M. R.; Murnaghan, K.; Chalaturnyk, R. J.

2012-12-01

The scientific objectives of the Aquistore CO2 storage project is to design, adapt, and test non-seismic monitoring methods that have not been systematically utilized to date for monitoring CO2 storage, and to integrate the data from these various monitoring tools to obtain quantitative estimates of the change in subsurface fluid distributions, pressure changes and associated surface deformation. For this an array of monitoring methodologies will be tested, including satellite-, surface- and wellbore-based monitoring systems. Interferometric Synthetic Aperture Radar (InSAR), GPS and tiltmeter monitoring will be used for measuring any ground deformation caused by CO2 injection and the associated subsurface pressure perturbation. In the spring-summer of 2012 we started collecting C-band SAR data from the Canadian Radarsat-2 satellite to provide baseline data over the study site. The Radarsat-2 data is acquired about every six days on average in five different geometries in order to achieve nearly uninterrupted coverage. We acquire ascending and descending spotlight data with sub-meter resolution (1.6x0.8 m), ascending and descending wide ultra fine data with moderate resolution (1.6x2.8 m) and descending fine quad-pol data with coarse resolution (5.2x7.6 m). Over the project life, this SAR coverage will be supplemented by X-band TerraSAR-X data, C-band Sentinel, and L-band ALOS-2 data. Availability of SAR data from all three wave-band sensors should allow us to measure ground deformation with a precision of a few mm/year. For mitigating temporal de-correlation and for improving precision during the winter when there will be snow cover, we will install 13 paired corner reflectors suitable for ascending and descending imaging. Multidimensional time series of ground deformation will be produced using MSBAS techniques (Samsonov and d'Oreye, 2012). PolInSAR methodology will be tested on fine quad-pol data. To obtain higher precision spatial and higher resolution temporal ground motion measurements we will install 13 continuous Global Positioning Systems (cGPS), and 5-6 tiltmeters in the fall of 2012. Various geodetic data will be integrated using the methodology of Samsonov et al., 2007 and resultant ground deformation maps will be used for validation of the geomechanical modelling. Here we will present maps of the injection site showing the locations and installation design of various geodetic sensors and provide initial results of InSAR measurements.

Influence of coherent mesoscale structures on satellite-based Doppler lidar wind measurements

NASA Technical Reports Server (NTRS)

Emmitt, G. D.; Houston, S.

1985-01-01

Efforts to develop display routines for overlaying gridded and nongridded data sets are discussed. The primary objective is to have the capability to review global patterns of winds and lidar samples; to zoom in on particular wind features or global areas; and to display contours of wind components and derived fields (e.g., divergence, vorticity, deformation, etc.). Current considerations in support of a polar orbiting shuttle lidar mission are discussed. Ground truth for a shuttle lidar experiment may be limited to fortuitous alignment of lidar wind profiles and scheduled rawinsonde profiles. Any improvement on this would require special rawinsonde launches and/or optimization of the shuttle orbit with global wind measurement networks.

Comparative analysis of recent satellite missions for multi-temporal SAR interferometry

NASA Astrophysics Data System (ADS)

Bovenga, Fabio; Refice, Alberto; Belmonte, Antonella; Pasquariello, Guido

2016-10-01

Multi-temporal InSAR (MTI) applications pose challenges related to the availability of coherent scattering from the ground surface, the complexity of the ground deformations, the atmospheric artifacts, the visibility problems related to the ground elevation. Nowadays, several satellite missions are available providing interferometric SAR data at different wavelengths, spatial resolutions, and revisit time. A new interesting opportunity is provided by Sentinel-1 mission, which has a spatial resolution comparable to previous ESA C-band missions, and revisit times reduced to up to 6 days. It is envisioned that, by offering regular, global-scale coverage, improved temporal resolution and freely available imagery, Sentinel-1 will guarantee an increasing use of MTI for ground displacement investigations. According to these different SAR space-borne missions, the present work discusses current and future opportunities of MTI applications to ground instability monitoring. Issues related to coherent target detection and mean velocity precision will be addressed through a simple theoretical model assuming backscattering mechanisms related to point scatterers. The paper also presents an example of multi-sensor ground instability investigation over the site of Marina di Lesina, Southern Italy, a village lying over a gypsum diapir, where a hydration process, involving the underlying anhydride, causes a smooth uplift pattern affecting the entire village area, and the formation of scattered sinkholes. More than 20 years of MTI SAR data have been used, coming from both legacy ERS and ENVISAT missions, and last-generation Radarsat-2, COSMO-SkyMed, and Sentinel-1A sensors.

Plains Tectonics on Venus

NASA Technical Reports Server (NTRS)

Banerdt, W. B.; McGill, G. E.; Zuber, M. T.

1996-01-01

Tectonic deformation in the plains of Venus is pervasive, with virtually every area of the planet showing evidence for faulting or fracturing. This deformation can be classified into three general categories, defined by the intensity and areal extent of the surface deformation: distributed deformation, concentrated deformation, and local fracture patterns.

The exploitation of large archives of space-borne C-band SAR data in the framework of FP7-DORIS Project

NASA Astrophysics Data System (ADS)

Del Ventisette, Chiara; Ciampalini, Andrea

2013-04-01

DORIS (Ground Deformations Risk Scenarios: an Advanced Assessment Service) is an advanced downstream service project within the seventh Framework Programme of the European Commission. A European team was set up in order to make the best views of the most advanced research and technologies outcomes in the field of Earth Observation (EO) for the improvement of risk management. The aim of the DORIS project is the development of new methodologies for the detection, mapping, monitoring and forecasting of ground deformations. DORIS integrates traditional and innovative EO and ground based (non-EO) data to improve our understanding of the complex phenomena at different temporal and spatial scales and in various physiographic and environmental settings that result in ground deformations, including landslides and ground subsidence, for civil protection purposes. One of the goal of the Doris Project is the exploitation of the large data archives for geohazards mapping. In this work the existing ESA Synthetic Aperture Radar (SAR) archives, operating in the microwave C-band (data collected by the ERS-1/2 and ENVISAT satellite) were analysed through new algorithms developed to reconstruct long time series (almost 20 years) and the obtained preliminary results are presented. The algorithms are based on Small BAseline Subset technique (SBAS; developed by CNR-IREA), ERS- ENVISAT Stitching (T.R.E.), Stable Point Network (SPN; Altamira) and ERS-ENVISAT Interferometric Point Target Analysis (IPTA; Gamma). The potentiality of these algorithms were evaluate in selected test sites characterized by different ground deformation phenomena (landslide and/or subsidence): i) Central Umbria (Italy); ii) Messina Province (Italy); iii) Rácalmás (Hungary); iv) Silesian Coal Basin (Poland); v) Tramuntana Range (Mallorca, Spain) and vi) St. Moritz (Switzerland). The results demonstrate the usefulness of the implemented algorithms, but in some cases there is a loss of the coherent points, especially in the most unstable areas.

Analysis of five years of continuous GPS recording at Piton de La Fournaise (R

NASA Astrophysics Data System (ADS)

Peltier, A.; Staudacher, T.; Boissier, P.; Lauret, F.; Kowalski, P.

2009-04-01

A network of twelve permanent GPS stations has been implemented since 2004 at Piton de La Fournaise (hot spot basaltic volcano of La Réunion Island, Indian Ocean) to follow the ground deformation associated with its high eruptive activity. During the period covered by the continuous GPS recording, 12 eruptions occurred. The compilation of the data recorded between 2004 and 2008 allows us to define two time scales of ground deformation systematically associated with this eruptive activity: (1) Large short-term displacements, reaching up to 14 mm/min, monitored a few min to hours prior each eruption during magma injections toward the surface (co-eruptive deformation); (2) But also, small long-term ground displacements recorded during inter-eruptive periods. Between 2 weeks and 5 months before each eruption a slight summit inflation occurs (0.4-0.7 mm/day); whereas a post-eruptive summit deflation lasting 1 to 3 months is only recorded after the largest distal eruptions (0.3 - 1.3 mm/day). These two time scales ground deformation precursors allowed us to forecast all eruptions up to five months in advance. And the follow up of the large short-term displacement in real-time allowed us to evaluated the approximate location of the eruptive fissure a few min to hours before its opening (i.e. inside the summit crater, northern flank or southern flank). The large short-term ground displacements have been attributed to the dyke propagation toward the surface, whereas the long-term ground displacements, which were also recorded by the extensometer network since 2000, have been attributed to a continuous over pressurization of the shallow magma reservoir located at about 2300m depth. The continuous over-pressurization of the shallow magma reservoir would explain the high eruptive activity observed since 1998; 27 eruptions in 10 years.

Spatial carrier color digital speckle pattern interferometry for absolute three-dimensional deformation measurement

NASA Astrophysics Data System (ADS)

Gao, Xinya; Wang, Yonghong; Li, Junrui; Dan, Xizuo; Wu, Sijin; Yang, Lianxiang

2017-06-01

It is difficult to measure absolute three-dimensional deformation using traditional digital speckle pattern interferometry (DSPI) when the boundary condition of an object being tested is not exactly given. In practical applications, the boundary condition cannot always be specifically provided, limiting the use of DSPI in real-world applications. To tackle this problem, a DSPI system that is integrated by the spatial carrier method and a color camera has been established. Four phase maps are obtained simultaneously by spatial carrier color-digital speckle pattern interferometry using four speckle interferometers with different illumination directions. One out-of-plane and two in-plane absolute deformations can be acquired simultaneously without knowing the boundary conditions using the absolute deformation extraction algorithm based on four phase maps. Finally, the system is proved by experimental results through measurement of the deformation of a flat aluminum plate with a groove.

Deformation at Lava Lake Volcanoes: Lessons from Karthala

NASA Astrophysics Data System (ADS)

Biggs, J.; Rust, A.; Owens, C.

2014-12-01

To remain hot, permanent lava lakes require a continuous connection to a magma reservoir. Depending on the state of the conduit, changes in magma pressure could result in changes in the lake level (hydraulic head) or be accommodated elastically leading to surface deformation. Observing deformation is therefore key to understanding the plumbing system associated with lava lakes. However, the majority of the world's lava lakes lie in difficult socio-economic or remote locations meaning that there are few ground-based observations, and it is often necessary to rely on satellite imagery. Karthala volcano experienced a sequence of eruptions in April 2005, Nov 2005, May 2006 and Jan 2007. The first 3 took place at the Choungou Chahale crater, which typically contains either a water or lava lake; the last formed a new pit crater to the north. Satellite thermal imagery (Hirn et al, 2008) does not show an anomaly during the first eruption, which had a phreatomagmatic component, but large thermal anomalies, associated with an ephemeral lava lake were detected during the Nov 2005 and May 2006 eruptions. The final eruption produced a smaller anomaly attributed to a minor lava flow. Here we present InSAR observations from 2004-2010. We find no significant deformation associated with the first three eruptions, but the January 2007 eruption was associated with ~25 cm of deformation near the volcano's summit, characteristic of a dyke intrusion aligned with the northern rift zone. We also observe an unusual pattern deformation along the coast which may be attributed to rapid settling of soft sediment or recent volcanic deposits triggered by seismic activity. We propose that the first eruption cleared the reservoir-summit connection and interacted with the water in Choungou Chahale. The following eruptions formed a lava lake, but without causing deformation. By the final eruption, the conduit had become blocked and magma intruded along the rift zone causing deformation but no thermal anomaly. The dyke intersected the surface at Choungou Chagnoumeni. At Karthala volcano, no deformation is associated with lava lake activity, but when the conduit is blocked, magma intrudes along the rift zone causing deformation. This is in contrast to observations at Kileauea in Hawaii, where both lake level changes and deformation occur simultaneously.

Thalamus surface shape deformity in obsessive-compulsive disorder and schizophrenia.

PubMed

Kang, Do-Hyung; Kim, Sun Hyung; Kim, Chi-Won; Choi, Jung-Seok; Jang, Joon Hwan; Jung, Myung Hun; Lee, Jong-Min; Kim, Sun I; Kwon, Jun Soo

2008-04-16

The authors performed a three-dimensional shape deformation analysis to clarify the various patterns of specific thalamic nuclei abnormality using three age-matched and sex-matched groups of 22 patients with obsessive-compulsive disorder (OCD), 22 patients with schizophrenia and 22 control participants. Compared with the healthy volunteers, the anterior, lateral outward surface deformities of the thalamus were significant in OCD patients, whereas the posterior, medial outward deformities of the thalamus were prominent in schizophrenia patients. In terms of thalamic asymmetry, both OCD and schizophrenia patients exhibited the loss of a leftward pattern of asymmetry on the posterior, medial surface of the thalamus. Different patterns of shape abnormality of specific thalamic nuclei may be related to the different phenomenology of OCD and schizophrenia.

Monitoring Seawall Deformation With Repeat-Track Space-Borne SAR Images

NASA Astrophysics Data System (ADS)

Pei, Yuanyuan; Wan, Qing; Wei, Lianhuan; Fang, Zhilei; Liao, Mingsheng

2010-10-01

Seawalls are constructed to protect coastal cities from typhoon, flood and sea tide. It is necessary to monitor the deformation of seawalls in real time. Repeat-track space-borne SAR images are useful for environment monitoring, especially ground deformation monitoring. Shanghai sits on the Yangtze River Delta on China's eastern coast. Each year, the city is hit by typhoons from Pacific Ocean and threatened by the flood of the Yangtze River. PS-InSAR technique is carried out to monitor the deformation of the seawalls. Experiment exhibits that the seawalls around Pudong airport and Lingang town suffered serious deformation.

Volcano geodesy: Challenges and opportunities for the 21st century

USGS Publications Warehouse

Dzurisin, D.

2000-01-01

Intrusions of magma beneath volcanoes deform the surrounding rock and, if the intrusion is large enough, the overlying ground surface. Numerical models generally agree that, for most eruptions, subsurface volume changes are sufficient to produce measurable deformation at the surface. Studying this deformation can help to determine the location, volume, and shape of a subsurface magma body and thus to anticipate the onset and course of an eruption. This approach has been successfully applied at many restless volcanoes, especially basaltic shields and silicic calderas, using various geodetic techniques and sensors. However, its success at many intermediate-composition strato-volcanoes has been limited by generally long repose intervals, steep terrain, and structural influences that complicate the history and shape of surface deformation. These factors have made it difficult to adequately characterize deformation in space and time at many of the world's dangerous volcanoes. Recent technological advances promise to make this task easier by enabling the acquisition of geodetic data of high spatial and temporal resolution from Earth-orbiting satellites. Synthetic aperture radar interferometry (InSAR) can image ground deformation over large areas at metre-scale resolution over time-scales of a month to a few years. Global Positioning System (GPS) stations can provide continuous information on three-dimensional ground displacements at a network of key sites -information that is especially important during volcanic crises. By using InSAR to determine the shape of the displacement field and GPS to monitor temporal changes at key sites, scientists have a much better chance to capture geodetic signals that have so far been elusive at many volcanoes. This approach has the potential to provide longer-term warnings of impending volcanic activity than is possible with other monitoring techniques.

Responses of retaining wall and surrounding ground to pre-excavation dewatering in an alternated multi-aquifer-aquitard system

NASA Astrophysics Data System (ADS)

Zeng, Chao-Feng; Xue, Xiu-Li; Zheng, Gang; Xue, Teng-Yun; Mei, Guo-Xiong

2018-04-01

Pre-excavation dewatering (PED) is an important construction stage in deep excavation. Field measurements show that retaining walls can develop obvious deflections during PED, which has been rarely considered in the past. The characteristics of PED-induced wall deflection, and the relationship of this deflection to surrounding ground deformation are still unclear. In this study, a PED test is simulated by a numerical model. The model is verified by field observations and used to investigate the responses of retaining wall and surrounding ground to PED. Results indicate that the maximum wall defection (δhm) and surface settlement (δvm) can all reach centimeter level under common conditions of PED. The ratio of δvm to δhm varies at the range of 0.45-0.67. Wall and soil deformations will be more obvious if the soils within the dewatering depth (Hd) have better permeability. The relative positions between Hd and strata (i.e., aquifer or aquitard) have great influence on the PED-induced deformations. If an aquifer appears below Hd, further increasing Hd can induce a rapid growth of wall and soil deformations. If thick aquitard appears below Hd, the deformation increments by further increasing Hd are not apparent. However, once Hd exceeds the center of the thick aquitard and reaches a thick confined aquifer, the wall deflections and soil deformation zones behind the wall will enlarge significantly. Meanwhile, a large bending moment in the retaining wall will arise around the bottom of the confined aquifer. The designers should consider this condition and allocate enough steel rebars there, preventing the appearance of wall cracks in the confined aquifer.

IMF By effects on ground magnetometer response to increased solar wind dynamic pressure derived from global MHD simulations

NASA Astrophysics Data System (ADS)

Ozturk, Dogacan Su; Zou, Shasha; Slavin, James A.

2017-05-01

During sudden solar wind dynamic pressure enhancements, the magnetosphere undergoes rapid compression resulting in a reconfiguration of the global current systems, most notably the field-aligned currents (FACs). Ground-based magnetometers are traditionally used to study such compression events. However, factors affecting the polarity and magnitude of the ground-based magnetic perturbations are still not well understood. In particular, interplanetary magnetic field (IMF) By is known to create significant asymmetries in the FAC patterns. We use the University of Michigan Block Adaptive Tree Roe Upwind Scheme (BATS'R'US) magnetohydrodynamic code to investigate the effects of IMF By on the global variations of ground magnetic perturbations during solar wind dynamic pressure enhancements. Using virtual magnetometers in three idealized simulations with varying IMF By, we find asymmetries in the peak amplitude and magnetic local time of the ground magnetic perturbations during the preliminary impulse (PI) and the main impulse (MI) phases. These asymmetries are especially evident at high-latitude ground magnetometer responses where the peak amplitudes differ by 50 nT at different locations. We show that the FACs related with the PI are due to magnetopause deformation, and the FACs related with the MI are generated by vortical flows within the magnetosphere, consistent with other simulation results. The perturbation FACs due to pressure enhancements and their magnetospheric sources do not differ much under different IMF By polarities. However, the conductance profile affected by the superposition of the preexisting FACs and the perturbation FACs including their closure currents is responsible for the magnitude and location asymmetries in the ground magnetic perturbations.

Constraints and conundrums resulting from ground-deformation measurements made during the 2004-2005 dome-building eruption of Mount St. Helens, Washington: Chapter 14 in A volcano rekindled: the renewed eruption of Mount St. Helens, 2004-2006

USGS Publications Warehouse

Dzurisin, Daniel; Lisowski, Michael; Poland, Michael P.; Sherrod, David R.; LaHusen, Richard G.; Sherrod, David R.; Scott, William E.; Stauffer, Peter H.

2008-01-01

Lack of precursory inflation suggests that the volcano was poised to erupt magma already stored in a crustal reservoir when JRO1 was installed in 1997. Trilateration and campaign GPS data indicate surface dilatation, presumably caused by reservoir expansion between 1982 and 1991, but no measurable deformation between 1991 and 2003. We conclude that all three of the traditionally reliable eruption precursors (seismicity, ground deformation, and volcanic gas emission) failed to provide warning that an eruption was imminent until a few days before a visible welt appeared at the surface--a situation reminiscent of the 1980 north-flank bulge at Mount St. Helens.

Multiscale deformation behavior for multilayered steel by in-situ FE-SEM

NASA Astrophysics Data System (ADS)

Tanaka, Y.; Kishimoto, S.; Yin, F.; Kobayashi, M.; Tomimatsu, T.; Kagawa, K.

2010-03-01

The multi-scale deformation behavior of multi-layered steel during tensile loading was investigated by in-situ FE-SEM observation coupled with multi-scale pattern. The material used was multi-layered steel sheet consisting of martensitic and austenitic stainless steel layers. Prior to in-situ tensile testing, the multi-scale pattern combined with a grid and random dots were fabricated by electron beam lithography on the polished surface in the area of 1 mm2 to facilitate direct observation of multi-scale deformation. Both of the grids with pitches of 10 μm and a random speckle pattern ranging from 200 nm to a few μm sizes were drawn onto the specimen surface at same location. The electron moiré method was applied to measure the strain distribution in the deformed specimens at a millimeter scale and digital images correlation method was applied to measure the in-plane deformation and strain distribution at a micron meter scale acquired before and after at various increments of straining. The results showed that the plastic deformation in the austenitic stainless steel layer was larger than the martensitic steel layer at millimeter scale. However, heterogeneous intrinsic grain-scale plastic deformation was clearly observed and it increased with increasing the plastic deformation.

Improving detection and identification of seismic signals due to landslides: a methodology based on field scale controlled experiments

NASA Astrophysics Data System (ADS)

Yfantis, G.; Carvajal, H. E.; Pytharouli, S.; Lunn, R. J.

2013-12-01

A number of published studies use seismic sensors to understand the physics involved in slope deformation. In this research we artificially induce failure to two meter scaled slopes in the field and use 12 short period 3D seismometers to monitor the failure. To our knowledge there has been no previous controlled experiments that can allow calibration and validation of the interpreted seismic signals. Inside the body of one of the artificial landslides we embed a pile of glass shards. During movement the pile deforms emitting seismic signals due to friction among the glass shards. Our aim is twofold: First we investigate whether the seismic sensors can record pre-cursory and failure signals. Secondly, we test our hypothesis that the glass shards produce seismic signals with higher amplitudes and a distinct frequency pattern, compared to those emitted by common landslide seismicity and local background noise. Two vertical faces, 2m high, were excavated 3m apart in high porous tropical clay. This highly attenuating material makes the detection of weak seismic signals challenging. Slope failure was induced by increasing the vertical load at the landslide's crown. Special care was taken in the design of all experimental procedures to not add to the area's seismic noise. Measurements took place during 18 hours (during afternoon and night) without any change in soil and weather conditions. The 3D sensors were placed on the ground surface close to the crown, forming a dense microseismic network with 5-to-10m spacing and two nanoseismic arrays, with aperture sizes of 10 and 20 m. This design allowed a direct comparison of the recorded signals emitted by the two landslides. The two faces failed for loading between 70 and 100kN and as a result the pile of glass shards was horizontally deformed allowing differential movement between the shards. After the main failure both landslides were continuing to deform due to soil compaction and horizontal displacement. We apply signal processing techniques to identify and locate the emitted signals related to slope movement, despite high background noise levels and high attenuating geological conditions. Results were groundproofed by visual observations. Our study shows that short period seismic sensors can successfully monitor the brittle behaviour of dry clays for deformations larger than 1 centimetre, as well as weak ground failures. The use of glass, or any other coarse and brittle material, has advantages over soil only, since the friction among the glass shards allows for a more distinct frequency pattern. This makes detection of slope movements easier at heterogeneous environments were signals are emitted following movements of different material types as well as in areas characterised by high background noise levels. Our results provide information on the slope behaviour, a powerful tool for geotechnical engineering applications.

Modal-pushover-based ground-motion scaling procedure

USGS Publications Warehouse

Kalkan, Erol; Chopra, Anil K.

2011-01-01

Earthquake engineering is increasingly using nonlinear response history analysis (RHA) to demonstrate the performance of structures. This rigorous method of analysis requires selection and scaling of ground motions appropriate to design hazard levels. This paper presents a modal-pushover-based scaling (MPS) procedure to scale ground motions for use in a nonlinear RHA of buildings. In the MPS method, the ground motions are scaled to match to a specified tolerance, a target value of the inelastic deformation of the first-mode inelastic single-degree-of-freedom (SDF) system whose properties are determined by the first-mode pushover analysis. Appropriate for first-mode dominated structures, this approach is extended for structures with significant contributions of higher modes by considering elastic deformation of second-mode SDF systems in selecting a subset of the scaled ground motions. Based on results presented for three actual buildings-4, 6, and 13-story-the accuracy and efficiency of the MPS procedure are established and its superiority over the ASCE/SEI 7-05 scaling procedure is demonstrated.

Centimeter-scale surface deformation caused by the 2011 Mineral, Virginia, earthquake sequence at the Carter farm site—Subsidiary structures with a quaternary history

USGS Publications Warehouse

Harrison, Richard W.; Schindler, J. Stephen; Pavich, Milan J.; Horton, J. Wright; Carter, Mark W.

2016-08-25

Centimeter-scale ground-surface deformation was produced by the August 23, 2011, magnitude (M) 5.8 earthquake that occurred in Mineral, Virginia. Ground-surface deformation also resulted from the earthquake aftershock sequence. This deformation occurred along a linear northeast-trend near Pendleton, Virginia. It is approximately 10 kilometers (km) northeast of the M5.8 epicenter and near the northeastern periphery of the epicentral area as defined by aftershocks. The ground-surface deformation extends over a distance of approximately 1.4 km and consists of parallel, small-scale (a few centimeters (cm) in amplitude) linear ridges and swales. Individual ridge and swale features are discontinuous and vary in length across a zone that ranges from about 20 meters (m) to less than 5 m in width. At one location, three fence posts and adjoining rails were vertically misaligned. Approximately 5 cm of uplift on one post provides a maximum estimate of vertical change from pre-earthquake conditions along the ridge and swale features. There was no change in the alignment of fence posts, indicating that deformation was entirely vertical. A broad monoclinal flexure with approximately 1 m of relief was identified by transit survey across surface deformation at the Carter farm site. There, surface deformation overlies the Carter farm fault, which is a zone of brittle faulting and fracturing along quartz veins, striking N40°E and dipping approximately 75°SE. Brecciation and shearing along this fault is interpreted as Quaternary in age because it disrupts the modern B-soil horizon. However, deformation is confined to saprolitized schist of the Ordovician Quantico Formation and the lowermost portion of overlying residuum, and is absent in the uppermost residuum and colluvial layer at the ground surface. Because there is a lack of surface shearing and very low relief, landslide processes were not a causative mechanism for the surface deformation. Two possible tectonic models and one non-tectonic model are considered: (1) tectonic, monoclinal flexuring along the Carter farm fault, probably aseismic, (2) tectonic, monoclinal flexuring related to a shallow (1–3 km) cluster of aftershocks (M2 to M3) that occurred approximately 1 to 1.5 km to the east of Carter farm, and (3) non-tectonic, differential response to seismic shaking between more-rigid quartz veins and soft residuum-saprolite under vertical motions that were created by Rayleigh surface waves radiating away from the August 23, 2011, hypocenter and propagating along strike of the Carter farm fault. These processes are not considered mutually exclusive, and all three support brittle deformation on the Carter farm fault during the Quaternary. In addition, abandoned stream valleys and active stream piracy are consistent with long-term uplift in vicinity of the Carter farm fault.

Coseismic and Posteismic Deformation of a Blind Thrust Ramp from the 3 July 2015 Mw 6.4 Pishan, China Earthquake Detected with Sentinel-1A Radar Interferometry

NASA Astrophysics Data System (ADS)

Li, Mingjia; Sun, Jianbao; Shen, Zheng-Kang

2016-08-01

Boosted by the launch of Sentinel-1A radar satellite from the European Space Agency (ESA), we now have the opportunity of fast, full and multiple coverage of the land based deformation field of earthquakes. Here we use the data to investigate a strong earthquake struck Pishan, western China on July 3, 2015. The earthquake fault is blind and no ground break features are found on-site, thus Synthetic Aperture Radar (SAR) data give full play to its technical advantage for the recovery of coseismic deformation field. By using the Sentinel-1A radar data in the Interferometric Wide Swath mode, we obtain 1 track of InSAR data over the struck region, and resolve the 3D ground deformation generated by the earthquake. Then the Line-of-Sight (LOS) InSAR data are inverted for the slip-distribution of the seismogenic fault.

Role of deformation in odd-even staggering in reaction cross sections for 30,31,32Ne and 36,37,38Mg isotopes

NASA Astrophysics Data System (ADS)

Urata, Y.; Hagino, K.; Sagawa, H.

2017-12-01

We discuss the role of pairing antihalo effect in the observed odd-even staggering in reaction cross sections for 30,31,32Ne and 36,37,38Mg isotopes by taking into account the ground-state deformation of these nuclei. To this end, we construct the ground-state density for the Ne,3130 and Mg,3736 nuclei based on a deformed Woods-Saxon potential, while for the 32Ne and 38Mg nuclei we also take into account the pairing correlation using the Hartree-Fock-Bogoliubov method. We demonstrate that, when the one-neutron separation energy is small for the odd-mass nuclei, a significant odd-even staggering still appears even with finite deformation, although the degree of staggering is somewhat reduced compared to the spherical case. This implies that the pairing antihalo effect in general plays an important role in generating the odd-even staggering in reaction cross sections for weakly bound nuclei.

Determination of Visual Figure and Ground in Dynamically Deforming Shapes

ERIC Educational Resources Information Center

Barenholtz, Elan; Feldman, Jacob

2006-01-01

Figure/ground assignment--determining which part of the visual image is foreground and which background--is a critical step in early visual analysis, upon which much later processing depends. Previous research on the assignment of figure and ground to opposing sides of a contour has almost exclusively involved static geometric factors--such as…

Decoherence induced deformation of the ground state in adiabatic quantum computation.

PubMed

Deng, Qiang; Averin, Dmitri V; Amin, Mohammad H; Smith, Peter

2013-01-01

Despite more than a decade of research on adiabatic quantum computation (AQC), its decoherence properties are still poorly understood. Many theoretical works have suggested that AQC is more robust against decoherence, but a quantitative relation between its performance and the qubits' coherence properties, such as decoherence time, is still lacking. While the thermal excitations are known to be important sources of errors, they are predominantly dependent on temperature but rather insensitive to the qubits' coherence. Less understood is the role of virtual excitations, which can also reduce the ground state probability even at zero temperature. Here, we introduce normalized ground state fidelity as a measure of the decoherence-induced deformation of the ground state due to virtual transitions. We calculate the normalized fidelity perturbatively at finite temperatures and discuss its relation to the qubits' relaxation and dephasing times, as well as its projected scaling properties.

Decoherence induced deformation of the ground state in adiabatic quantum computation

PubMed Central

Deng, Qiang; Averin, Dmitri V.; Amin, Mohammad H.; Smith, Peter

2013-01-01

Despite more than a decade of research on adiabatic quantum computation (AQC), its decoherence properties are still poorly understood. Many theoretical works have suggested that AQC is more robust against decoherence, but a quantitative relation between its performance and the qubits' coherence properties, such as decoherence time, is still lacking. While the thermal excitations are known to be important sources of errors, they are predominantly dependent on temperature but rather insensitive to the qubits' coherence. Less understood is the role of virtual excitations, which can also reduce the ground state probability even at zero temperature. Here, we introduce normalized ground state fidelity as a measure of the decoherence-induced deformation of the ground state due to virtual transitions. We calculate the normalized fidelity perturbatively at finite temperatures and discuss its relation to the qubits' relaxation and dephasing times, as well as its projected scaling properties. PMID:23528821

Modelling of deformation of underground tunnel lining, interacting with water-saturated soil

NASA Astrophysics Data System (ADS)

Berezhnoi, D. V.; Balafendieva, I. S.; Sachenkov, A. A.; Sekaeva, L. R.

2016-11-01

Built finite element method of calculating the deformation of underground tunnel lining, interacting with dry and water-saturated soils. To simulate the interaction between the lining and soils environments, including physical and non-linear, a special "contact" finite element, which allows to consider all cases of interaction between the contacting surfaces. It solved a number of problems of deformation with the ground subway tunnel lining rings.

Ground-state properties of neutron-rich Mg isotopes

NASA Astrophysics Data System (ADS)

Watanabe, S.; Minomo, K.; Shimada, M.; Tagami, S.; Kimura, M.; Takechi, M.; Fukuda, M.; Nishimura, D.; Suzuki, T.; Matsumoto, T.; Shimizu, Y. R.; Yahiro, M.

2014-04-01

We analyze recently measured total reaction cross sections for 24-38Mg isotopes incident on 12C targets at 240 MeV/nucleon by using the folding model and antisymmetrized molecular dynamics (AMD). The folding model well reproduces the measured reaction cross sections, when the projectile densities are evaluated by the deformed Woods-Saxon (def-WS) model with AMD deformation. Matter radii of 24-38Mg are then deduced from the measured reaction cross sections by fine tuning the parameters of the def-WS model. The deduced matter radii are largely enhanced by nuclear deformation. Fully microscopic AMD calculations with no free parameter well reproduce the deduced matter radii for 24-36Mg, but still considerably underestimate them for 37,38Mg. The large matter radii suggest that 37,38Mg are candidates for deformed halo nucleus. AMD also reproduces other existing measured ground-state properties (spin parity, total binding energy, and one-neutron separation energy) of Mg isotopes. Neutron-number (N) dependence of deformation parameter is predicted by AMD. Large deformation is seen from 31Mg with N =19 to a drip-line nucleus 40Mg with N =28, indicating that both the N =20 and 28 magicities disappear. N dependence of neutron skin thickness is also predicted by AMD.

Site response, shallow shear-wave velocity, and damage in Los Gatos, California, from the 1989 Loma Prieta earthquake

USGS Publications Warehouse

Hartzell, S.; Carver, D.; Williams, R.A.

2001-01-01

Aftershock records of the 1989 Loma Prieta earthquake are used to calculate site response in the frequency band of 0.5-10 Hz at 24 locations in Los Gatos, California, on the edge of the Santa Clara Valley. Two different methods are used: spectral ratios relative to a reference site on rock and a source/site spectral inversion method. These two methods complement each other and give consistent results. Site amplification factors are compared with surficial geology, thickness of alluvium, shallow shear-wave velocity measurements, and ground deformation and structural damage resulting from the Loma Prieta earthquake. Higher values of site amplification are seen on Quaternary alluvium compared with older Miocene and Cretaceous units of Monterey and Franciscan Formation. However, other more detailed correlations with surficial geology are not evident. A complex pattern of alluvial sediment thickness, caused by crosscutting thrust faults, is interpreted as contributing to the variability in site response and the presence of spectral resonance peaks between 2 and 7 Hz at some sites. Within the range of our field measurements, there is a correlation between lower average shear-wave velocity of the top 30 m and 50% higher values of site amplification. An area of residential homes thrown from their foundations correlates with high site response. This damage may also have been aggravated by local ground deformation. Severe damage to commercial buildings in the business district, however, is attributed to poor masonry construction.

Monitoring of urban subsidence with SAR interferometric point target analysis: A case study in Suzhou, China

NASA Astrophysics Data System (ADS)

Zhang, Yonghong; Zhang, Jixian; Wu, Hongan; Lu, Zhong; Guangtong, Sun

2011-10-01

Ground subsidence, mainly caused by over exploitation of groundwater and other underground resources, such as oil, gas and coal, occurs in many cities in China. The annual direct loss associated with subsidence across the country is estimated to exceed 100 million US dollar. Interferometric SAR (InSAR) is a powerful tool to map ground deformation at an unprecedented level of spatial detail. It has been widely used to investigate the deformation resulting from earthquakes, volcanoes and subsidence. Repeat-pass InSAR, however, may fail due to impacts of spatial decorrelation, temporal decorrelation and heterogeneous refractivity of atmosphere. In urban areas, a large amount of natural stable radar reflectors exists, such as buildings and engineering structures, at which radar signals can remain coherent during a long time interval. Interferometric point target analysis (IPTA) technique, also known as persistent scatterers (PS) InSAR is based on these reflectors. It overcomes the shortfalls in conventional InSAR. This paper presents a procedure for urban subsidence monitoring with IPTA. Calculation of linear deformation rate and height residual, and the non-linear deformation estimate, respectively, are discussed in detail. Especially, the former is highlighted by a novel and easily implemented 2-dimensional spatial search algorithm. Practically useful solutions that can significantly improve the robustness of IPTA, are recommended. Finally, the proposed procedure is applied to mapping the ground subsidence in Suzhou city, Jiangsu province, China. Thirty-four ERS-1/2 SAR scenes are analyzed, and the deformation information over 38,881 point targets between 1992 and 2000 are generated. The IPTA-derived deformation estimates correspond well with leveling measurements, demonstrating the potential of the proposed subsidence monitoring procedure based on IPTA technique. Two shortcomings of the IPTA-based procedure, e.g., the requirement of large number of SAR images and assumed linear plus non-linear deformation model, are discussed as the topics of further research.

Application of ASAR-ENVISAT Data for Monitoring Andean Volcanic Activity : Results From Lastarria-Azufre Volcanic Complex (Chile-Argentina)

NASA Astrophysics Data System (ADS)

Froger, J.; Remy, D.; Bonvalot, S.; Franco Guerra, M.

2005-12-01

Since the pioneer study on Mount Etna by Massonnet et al., in 1995, several works have illustrated the promising potentiality of Synthetic Aperture Radar Interferometry (INSAR) for the monitoring of volcanoes. In the case of wide, remote or hazardous volcanic areas, in particular, INSAR represents a safer and more economic way to acquire measurements than from ground based geodetic networks. Here we present the preliminary results of an interferometric survey made with ASAR-ENVISAT data on a selection of South American volcanoes where deformation signals had been previously evidenced or are expected. An interesting result is the detection of a present-day active ground deformation on the Azufre-Lastarria area (Chile-Argentina) indicating that process, identified during 1998-2000 by Pritchard and Simmons (2004) from ERS data, is still active. The phase signal visible on ASAR interferograms (03/2003-06/2005) is roughly elliptical with a 45 km NNE-SSW major axis. Its amplitude increases as a function of time and is compatible with ground uplift in the line of sight of the satellite. The ASAR time series (up to 840 days, 7 ASAR images) indicates variable deformation rate that might confirm the hypothesis of a non uniform deformation process. We investigated the origin and the significance of the deformation using various source modelling strategies (analytical and numerical). The observed deformation can be explained by the infilling of an elliptical magmatic reservoir lying between 7 and 10 km depth. The deformation could represent the first stage of a new caldera forming as it is correlated with a large, although subtle, topographic depression surrounded by a crown of monogenetic centers. A short wavelength inflation has also been detected on Lastaria volcano. It could result from the on-going infilling of a small subsurface magmatic reservoir, eventually supplied by the deeper one. All these observations point out the need of a closer monitoring of this area in order to assess future volcanic hazard.

Detection of the Subsidence Affecting a Shopping Center in Marseilles (France) using Sar Interferometry

NASA Astrophysics Data System (ADS)

Feurer, D.; Le Mouelic, S.; Raucoules, D.; Carnec, C.; Nédellec, J.-L.

2004-06-01

Help of satellite radar interferometry for urban subsidence observation has been demonstrated for several years now. This monitoring tool is able to provide an assessment of the ground motion with a millimetric accuracy and a large spatial coverage. We present here a result of this technique applied to the monitoring of a small area : the shopping centre complex and cinema multiplex in Marseilles, France. This construction work was one of the most important construction site of this last few years in France. Inaugurated in October, 1997, the multiplex had to close 6 of its 15 cinemas five months later because of collapsing risks due to important ground movements. It has been totally closed in July, 1999. The multiplex building demolition is currently under way. Finally, this "flop" represents a cost of 30 millions euros. 14 ERS images acquired between 1992 and 2000 had been processed in order to produce a set of 105 differential interferograms. We performed a recursive correction of orbital and topographic fringes using a FFT computation and a Digital Elevation Model provided by the French National Institute (IGN). The analysis of the interferograms series has allowed to detect unambiguously a signature of few pixels corresponding to the ground movement. From this study, we observed a ground deformation during 1997 to 1998, an overall stability during late 1998 to 1999 and again a deformation during late 1999 to 2000. This study shows that, in specific cases, traditional InSAR is able to provide valuable information on very localised ground deformation. It also shows the interest of a comprehensive study of the full ERS archive of this site in order to assess the stability of the ground before, when no ground-based measurements were available, during, and after the construction works.

Seismic imaging beneath an InSAR anomaly in eastern Washington State: Shallow faulting associated with an earthquake swarm in a low-hazard area

USGS Publications Warehouse

Stephenson, William J.; Odum, Jackson K.; Wicks, Chuck; Pratt, Thomas L.; Blakely, Richard J.

2016-01-01

In 2001, a rare swarm of small, shallow earthquakes beneath the city of Spokane, Washington, caused ground shaking as well as audible booms over a five‐month period. Subsequent Interferometric Synthetic Aperture Radar (InSAR) data analysis revealed an area of surface uplift in the vicinity of the earthquake swarm. To investigate the potential faults that may have caused both the earthquakes and the topographic uplift, we collected ∼3  km of high‐resolution seismic‐reflection profiles to image the upper‐source region of the swarm. The two profiles reveal a complex deformational pattern within Quaternary alluvial, fluvial, and flood deposits, underlain by Tertiary basalts and basin sediments. At least 100 m of arching on a basalt surface in the upper 500 m is interpreted from both the seismic profiles and magnetic modeling. Two west‐dipping faults deform Quaternary sediments and project to the surface near the location of the Spokane fault defined from modeling of the InSAR data.

Ground deformations along Ionian coastline of the northern Calabria (Southern Italy) from Capo Trionto to Capo Colonna detected by InSAR data

NASA Astrophysics Data System (ADS)

Vollrath, Andreas; Cianflone, Giuseppe; Bignami, Christian; Brunori, Carlo Alberto; Dominici, Rocco; Zucca, Francesco; Stramondo, Salvatore; Baldi, Paolo; Fabris, Massimo; Sepe, Vincenzo; Anzidei, Marco

2015-04-01

The study area is located along the Ionian coast of the northern Calabrian Arc, in correspondence of the Crotone and Spartivento fore-arc basins. The investigated coastal area represents the western margin of the Gulf of Taranto. The seafloor of this sector has been investigated by several authors during the last three decades and is characterized by numerous submarine depositional systems strictly related to main drainage basins which feed into the Ionian Sea. Northward, the area is limited by the Corigliano Canyon which connects the continental shelf with the Taranto Valley and separates the Cariati and Cirò Ridges. The latter is bounded, along its southern side, by the NW-SE trending Alice Canyon which reaches the inner continental shelf offshore Punta Alice and is not related to an onshore drainage system. Southward, the wide Neto-Lipuda Canyons system originates close to the coastline and is connected to the Neto and Lipuda Rivers. Toward South, this system is separated from the Esaro Canyon by the Luna-Hera Lacinia High. The southernmost canyon is connected to the Esaro River and runs subparallel to the coastline. Previous authors have been highlighted ground deformations, with sometimes associated km-long surface fractures and damages to buildings, in the Cirò coastal plain and in the area southward from Crotone. The cause of these deformation is attributed to megaslides. The multi-temporal (1958, 1985, 1998, 2008) analysis of the coastline variations shows a general erosive trend characterized by m and dm coastline retreats. We applied the multi-temporal StaMPS SBAS technique for two SAR datasets, one acquired from 2003 up to 2010 by Envisat ASAR instrument, and another from 1995 up to 2000 from the ERS satellite (ESA, European Space Agency) to investigate ground displacements in the studied coastal area. The Up component (recording the vertical ground deformation) allows to identify the main subsidence areas in correspondence of the Capo Colonna promontory, Punta Alice, the deltas of the Neto and Nicà Rivers, the Crotone, Cirò Marina and Cariati harbours. The East component (recording the horizontal ground deformation) shows a weak stability/eastward movements from Capo Trionto to the mouth of the Esaro River, while the coastal sector moving southward from Crotone city records an eastward displacement. In addition to SAR data, we have used a set of aerial photogrammetric scenes collected in the time span 1940-2007. Therefore we have reconstructed in detail the timing of the continuous changes of the coastlines in the areas of Punta Alice due to vertical land deformation and sea level change. Our preliminary results allow to suppose a correlation between ground deformations of the coastal area and the morphobathimetric setting and evolution (e.g., canyon head retreat) of the offshore sector.

Subway Subsidence Monitoring and Analysis in Beijing through Envisat-Asar and Terrasar-X DATA

NASA Astrophysics Data System (ADS)

Duan, G.; Gong, H.; Chen, B.; Li, X.

2014-12-01

Subway plays a significant role in public transport in Beijing, China. The safe operation of such underground rail transports are serious threatened by ground subsidence that mainly caused by groundwater over-exploitation. It is necessary to carry out a continuous observation and analysis of the surface deformation along the newly built rails. The paper mainly studied four subways which were built in different periods(see attachment). Envisat-ASAR and Terrasar-X images of the study area were selected to measure the ground deformation. Interferometric Point Target Analysis method was gathered to process the SAR data. The method is developed based on the idea of the Permanent Scatterers SAR Interferometry method which can overcome the decorrelation and atmospheric effect to gain more precise estimation of the ground deformation. The master image can be selected according to the perpendicular, Doppler and temporal baselines to minimize the potential decorrelation. After the registration of all slave images to the master image, the PS candidates would be detected on the basis of the scattering properties of the images. A complex operation of the PSs was conducted to obtain the interferometric phase which was composed of terrain phase, atmospheric phase, deformation phase and noise. A model used for the evaluation of the contribution of each component was built by means of the least squares method. The deformation phase would be the remaining of the interferometric phase minus disturbance terms. Deformation information that came from two different kinds of data was jointly analyzed to reveal the temporal character of the rails before, during and after they were built. The regional LOS(line-of-sight) velocity around a special subway station shows that the rail has suffered from a serious uneven settlement along the rail during the observation period. In addition, time series data revealed the characteristic stages of each PS point. There is a clear accelerating trend of settlement in the construction period of the subway, and the sedimentation velocity would remain very high after a period of the opening of the line. Overall, ground subsidence had a certain delay when compared to the construction and operation of the subway.

Soft-sediment deformation in New Zealand: Structures resulting from the 2010/11 Christchurch earthquakes and comparison with Pleistocene sediments of the Taupo Volcanic Zone (TVZ)

NASA Astrophysics Data System (ADS)

Scholz, C.; Downs, D. T.; Gravley, D.; Quigley, M.; Rowland, J. V.

2011-12-01

The distinction between seismites and other event-related soft-sediment deformation is a challenging problem. Recognition and interpretation is aided by comparison of recent examples produced during known seismic events and those generated experimentally. Seismites are important features, once recognized in a rock, for interpretations of paleotectonic environment, tectonic relationships of sediments in basins, sedimentary facies analysis, evaluation of earthquake frequency and hazard and consequent land managment. Two examples of soft-sediment deformation, potentially generated through ground shaking and associated liquefaction, are described from within the TVZ: 1) Near Matata on the western margin of the Whakatane Graben. This location has a complicated en-echelon fault history and large earthquakes occur from time to time (e.g., 1987 ML6.3 Edgecumbe event). The structures occur in ~550 ka volcanic sediments, and represent soft-sediment deformation within stratigraphically-bounded layers. Based on paleoenvironment, appearance, and diagnostic criteria described by other authors (Sims 1975; Hempton and Dewey 1983), we interpret these features to have formed by ground shaking related to an earthquake and/or possibly accompanying large volcanic eruptions, rather than by slope failure. 2) Near Taupo, 3 km from the active Kaiapo fault. Lakeward dipping, nearly horizontal lacustrine sediments overlay Taupo Ignimbrite (1.8 ka). At one outcrop the lake beds have subsided into the underlying substrate resulting in kidney-shaped features. These structures formed as a result of liquefaction of the underlying substrate, which may have been caused by ground shaking related to either seismic or volcanic activity. However, inferred time relationships are more consistent with seismic-induced ground shaking. We compare and contrast the form and geometry of the above structures with seismites generated during the recent Christchurch earthquakes (Sep. 2010 and Feb. 2011). Hempton, M. R. and J. F. Dewey (1983). "Earthquake-induced deformational structures in young lacustrine sediments, East Anatolian Fault, southeast Turkey." Tectonophysics 98(3-4): T7-T14. Sims, J. D. (1975). "Determining earthquake recurrence intervals from deformational structures in young lacustrine sediments." Tectonophysics 29(1-4): 141-152.

Transient Surface Deformation of Northern Taiwan, 2007-2011, Using Persistent Scattered InSAR with ALOS Data

NASA Astrophysics Data System (ADS)

Wang, C.; Chang, W.; Chang, C.

2013-12-01

The Taipei basin, triangular in shape and located in the northern Taiwan, is now developed into the most densely populated area and also the capital of politics and economics in Taiwan. North of the Taipei basin, the Tatun volcano group was proposed to be the cause of extensional collapse during the Pleistocene following the collision between the Luzon volcanic arc and the Eurasian continental margin at about 5 Ma. We investigated the contemporary surface deformation of the northern Taiwan using ALOS images that cover the Taipei basin and its surrounding mountainous area. The Differential Interferometric Synthetic Aperture Radar (DInSAR) technique has been widely used in the past ten years. However, the mountainous areas surrounding the basin are mostly covered with densely various vegetations that reduce signal-to-noise ratio in the interferograms. Therefore, the DInSAR technique is not effective for measuring the surface deformation in and around the Taipei basin, including the Tatun volcano area, and consequently the Persistent Scatterer (PS) and small baseline (SB) InSAR techniques have been employed to extract phase signals of the chosen PS points. In this study, we aim to measure the ground deformation of northern Taiwan by processing the spaceborne radar interferometry data of ALOS acquired from 2007 to 2011 using PSInSAR and SBInSAR techniques. Compared with the Envisat and ERS images used by previous studies, L-band PALSAR images can produce more PS points in the region covered by dense vegetation so that our results reveal a higher resolution of ground deformation. The mean Line of Sight (LOS) velocity field of up to 8 mm/yr in the central Tatun volcanic area, and up to 5 mm/yr in the Taipei basin with higher rate at the hanging wall of the Sanchiao fault than the footwall. (See the Figure.) While previous studies indicated that the Taipei basin had experienced ground uplift from 1993 to 2001 and subsidence from 2003 to 2008, our results show a return to ground uplift from 2007 to 2011. Re-examining earlier InSAR and integrating other geodetic data is under progress for further examination on this transient deformation.

Gait patterns in hemiplegic patients with equinus foot deformity.

PubMed

Manca, M; Ferraresi, G; Cosma, M; Cavazzuti, L; Morelli, M; Benedetti, M G

2014-01-01

Equinus deformity of the foot is a common feature of hemiplegia, which impairs the gait pattern of patients. The aim of the present study was to explore the role of ankle-foot deformity in gait impairment. A hierarchical cluster analysis was used to classify the gait patterns of 49 chronic hemiplegic patients with equinus deformity of the foot, based on temporal-distance parameters and joint kinematic measures obtained by an innovative protocol for motion assessment in the sagittal, frontal, and transverse planes, synthesized by parametrical analysis. Cluster analysis identified five subgroups of patients with homogenous levels of dysfunction during gait. Specific joint kinematic abnormalities were found, according to the speed of progression in each cluster. Patients with faster walking were those with less ankle-foot complex impairment or with reduced range of motion of ankle-foot complex, that is with a stiff ankle-foot complex. Slow walking was typical of patients with ankle-foot complex instability (i.e., larger motion in all the planes), severe equinus and hip internal rotation pattern, and patients with hip external rotation pattern. Clustering of gait patterns in these patients is helpful for a better understanding of dysfunction during gait and delivering more targeted treatment.

Description Of Scoliotic Deformity Pattern By Harmonic Functions

NASA Astrophysics Data System (ADS)

Drerup, Burkhard; Hierholzer, Eberhard

1989-04-01

Frontal radiographs of scoliotic deformity of the spine reveal a characteristic pattern of lateral deviation, lateral tilt and axial rotation of vertebrae. In order to study interrelations between deformation parameters 478 radiographs of idiopathic scolioses, 23 of scolioses after Wilms-tumor treatment and 18 of scolioses following poliomyelitis were digitized. From these the curves of lateral deviation, tilt and rotation are calculated and fitted by Fourier series. By restriction to the first harmonic, analysis reduces to the analysis of a single phase and amplitude for each curve. Justification of this simplification will be discussed. Results provide a general geometric description of scoliotic deformity.

Crustal deformation, the earthquake cycle, and models of viscoelastic flow in the asthenosphere

NASA Technical Reports Server (NTRS)

Cohen, S. C.; Kramer, M. J.

1983-01-01

The crustal deformation patterns associated with the earthquake cycle can depend strongly on the rheological properties of subcrustal material. Substantial deviations from the simple patterns for a uniformly elastic earth are expected when viscoelastic flow of subcrustal material is considered. The detailed description of the deformation pattern and in particular the surface displacements, displacement rates, strains, and strain rates depend on the structure and geometry of the material near the seismogenic zone. The origin of some of these differences are resolved by analyzing several different linear viscoelastic models with a common finite element computational technique. The models involve strike-slip faulting and include a thin channel asthenosphere model, a model with a varying thickness lithosphere, and a model with a viscoelastic inclusion below the brittle slip plane. The calculations reveal that the surface deformation pattern is most sensitive to the rheology of the material that lies below the slip plane in a volume whose extent is a few times the fault depth. If this material is viscoelastic, the surface deformation pattern resembles that of an elastic layer lying over a viscoelastic half-space. When the thickness or breath of the viscoelastic material is less than a few times the fault depth, then the surface deformation pattern is altered and geodetic measurements are potentially useful for studying the details of subsurface geometry and structure. Distinguishing among the various models is best accomplished by making geodetic measurements not only near the fault but out to distances equal to several times the fault depth. This is where the model differences are greatest; these differences will be most readily detected shortly after an earthquake when viscoelastic effects are most pronounced.

Deformation Monitoring of Waste-Rock-Backfilled Mining Gob for Ground Control

PubMed Central

Zhao, Tongbin; Zhang, Yubao; Zhang, Zhenyu; Li, Zhanhai; Ma, Shuqi

2017-01-01

Backfill mining is an effective option to mitigate ground subsidence, especially for mining under surface infrastructure, such as buildings, dams, rivers and railways. To evaluate its performance, continual long-term field monitoring of the deformation of backfilled gob is important to satisfy strict public scrutiny. Based on industrial Ethernet, a real-time monitoring system was established to monitor the deformation of waste-rock-backfilled gob at −700 m depth in the Tangshan coal mine, Hebei Province, China. The designed deformation sensors, based on a resistance transducer mechanism, were placed vertically between the roof and floor. Stress sensors were installed above square steel plates that were anchored to the floor strata. Meanwhile, data cables were protected by steel tubes in case of damage. The developed system continually harvested field data for three months. The results show that industrial Ethernet technology can be reliably used for long-term data transmission in complicated underground mining conditions. The monitoring reveals that the roof subsidence of the backfilled gob area can be categorized into four phases. The bearing load of the backfill developed gradually and simultaneously with the deformation of the roof strata, and started to be almost invariable when the mining face passed 97 m. PMID:28475168

Deformation Monitoring of Waste-Rock-Backfilled Mining Gob for Ground Control.

PubMed

Zhao, Tongbin; Zhang, Yubao; Zhang, Zhenyu; Li, Zhanhai; Ma, Shuqi

2017-05-05

Backfill mining is an effective option to mitigate ground subsidence, especially for mining under surface infrastructure, such as buildings, dams, rivers and railways. To evaluate its performance, continual long-term field monitoring of the deformation of backfilled gob is important to satisfy strict public scrutiny. Based on industrial Ethernet, a real-time monitoring system was established to monitor the deformation of waste-rock-backfilled gob at -700 m depth in the Tangshan coal mine, Hebei Province, China. The designed deformation sensors, based on a resistance transducer mechanism, were placed vertically between the roof and floor. Stress sensors were installed above square steel plates that were anchored to the floor strata. Meanwhile, data cables were protected by steel tubes in case of damage. The developed system continually harvested field data for three months. The results show that industrial Ethernet technology can be reliably used for long-term data transmission in complicated underground mining conditions. The monitoring reveals that the roof subsidence of the backfilled gob area can be categorized into four phases. The bearing load of the backfill developed gradually and simultaneously with the deformation of the roof strata, and started to be almost invariable when the mining face passed 97 m.

Spatial scale of deformation constrained by combinations of InSAR and GPS observations in Southern California

NASA Astrophysics Data System (ADS)

Lohman, R. B.; Scott, C. P.

2014-12-01

Efforts to understand the buildup and release of strain within the Earth's crust often rely on well-characterized observations of ground deformation, over time scales that include interseismic periods, earthquakes, and transient deformation episodes. Constraints on current rates of surface deformation in 1-, 2- or 3-dimensions can be obtained by examining sets of GPS and Interferometric Synthetic Aperture Radar (InSAR) observations, both alone and in combination. Contributions to the observed signal often include motion along faults, seasonal cycles of subsidence and recharge associated with aquifers, anthropogenic extraction of hydrocarbons, and variations in atmospheric water vapor and ionospheric properties. Here we examine methods for extracting time-varying ground deformation signals from combinations of InSAR and GPS data, real and synthetic, applied to Southern California. We show that two methods for combining the data through removal of a GPS-constrained function (a plane, and filtering) from the InSAR result in a clear tradeoff between the contribution from the two datatypes at diffferent spatial scales. We also show that the contribution to the secular rates at GPS sites from seasonal signals is large enough to be a significant error in this estimation process, and should be accounted for.

3D displacements maps of the L'Aquila earthquake by applying SISTEM method to GPS and ENVISAT and ALOS DInSAR data

NASA Astrophysics Data System (ADS)

Guglielmino, Francesco; Anzidei, Marco; Briole, Pierre; de Michele, Marcello; Elias, Panagiotis; Nunnari, Giuseppe; Puglisi, Giuseppe; Spata, Alessandro

2010-05-01

We present an application of the novel SISTEM (Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements) approach [Guglielmino et al., 2009] to obtain a 3D estimation of the ground deformation pattern produced by the April 6, 2009, Mw 6.3 L'Aquila earthquake, the most destructive in the Abruzzo region since the huge 1703 earthquake [Boschi et al., 2000; Chiarabba et al., 2005]. The focal mechanism of the main shock is of normal faulting with NE-SW oriented T-axis [INGV, 2009]. Most of the aftershocks, located by the INGV seismic network, are in the depth range 5÷15 km, depicting a SW dipping fault plane [INGV, 2009]. Field observations [EMERGEO working group, 2009] have identified surface ground cracks with centimeter to decimeters throws over a wide belt running along the Paganica Fault. A closely spaced GPS (Global Positioning System) network was set up in this sector of the Apennines after 1999 [Anzidei et al., 2005] and more than 10 Continuous GPS (CGPS) stations have been operating in this region over the last years. On March 30 2008, INGV installed five GPS receivers on selected benchmarks of the Central Apennine Geodetic Network (CaGeoNet) bordering the L'Aquila basin in order to detect the eventual ground movements during the seismic sequence. These stations were crucial to resolve the near-field co-seismic deformation pattern properly, allowing direct observation of the details of co-seismic displacement related to the main shock. Thanks to the ESA Earth Watching project, which made Envisat data quickly available after their acquisition, we performed a DInSAR (Differential Interferometric Synthetic Aperture Radar) analysis of ascending and descending images sampling the date of the earthquake. In particular, we analyze the descending pair for the interval 27/04/2008 - 12/04/2009 (tbline = 350 days; Bperp = 44m) and the ascending pair for the interval 11/03/2009 - 15/04/2009 (tbline = 35 days; Bperp = 227m). We also analyzed ALOS PALSAR interferograms produced with images acquired along two different ascending tracks and relevant to the 3/7/2008 - 21/5/2009 time interval (track 638; tbline = 322 days; Bperp = 665 m ) and 2/3/2007 - 22/4/2009 time interval (track 639; tbline = 782 days; Bperp = 466 m ). In order to derive 3D surface motion maps, we apply the SISTEM method to the available geodetic dataset (both GPS and DInSAR). The SISTEM method performs an integration of GPS and DInSAR data for computing displacements on each point of the studied area. The SISTEM is based on elastic theory, and provides the complete 3D strain and the rigid body rotation tensors in the same solution. To achieve higher accuracy and get better the constraint of the 3D components of the displacements, we improved the standard formulation of SISTEM approach, based on a single DInSAR data, in order to take into account both ascending and descending interferograms and the DInSAR data acquired by different sensors(ALOS and ENVISAT). The SISTEM integration results show a complex kinematics, where the main movements (max westward movement of 165 mm associated with a max lowering of 260 mm) are recorded in the area between the surface evidence of the Paganica fault and Monticchio-fossa fault. These results, which provide both accurate and fine spatial characterization of ground deformation, are hence promising for future studies aimed at improving the knowledge of the kinematic of the Paganica fault and identification of additional faults responsible of the seismic sequence and that have contributed to the observed ground deformation. References. Anzidei, M., P. Baldi, A. Pesci, A. Esposito, A. Galvani, F. Loddo, P. Cristofoletti, A. Massucci, and S. Del Mese (2005), Geodetic deformation across the Central Apennines from GPS data in the time span 1999-2003, Ann. Geophys., 48(2), 259-271. Boschi, E., E. Guidoboni, G. Ferrrari, D. Mariotti, G. Valensise, and P. Gasperini (2000), Catalogue of strong Italian earthquakes from 461 B.C. to 1997, Ann. Geofis., 43, 609- 868. Chiarabba, C., L. Jovane, and R. Di Stefano (2005), A new view of Italian seismicity using 20 years of instrumental recordings, Tectonophysics, 395, 251-268, doi:10.1016/j.tecto.2004.09.013. EMERGEO Working Group (2009), Field geological survey in the epicentral area of the Abruzzi (central Italy) seismic sequence of April 6th, 2009, in Quaderni di Geofisica, vol. 70, Ist. Naz. Di Geofis. e Vulcanol., Rome. Guglielmino F., Nunnari G., Puglisi G., Spata A. (2009), Simultaneous and Integrated Strain Tensor Estimation from geodetic and satellite deformation Measurements (SISTEM) to obtain threedimensional displacements maps. Submitted to IEEE Transactions on Geoscience and Remote Sensing. Istituto Nazionale di Geofisica e Vulcanologia (INGV) (2009), The L'Aquila seismic sequence— April 2009, Ist. Naz. di Geofis. e Vulcanol., Rome. (Available at http://portale.ingv.it/).

PSP SAR interferometry monitoring of ground and structure deformations in the archeological site of Pompeii

NASA Astrophysics Data System (ADS)

Costantini, Mario; Francioni, Elena; Paglia, Luca; Minati, Federico; Margottini, Claudio; Spizzichino, Daniele; Trigila, Alessandro; Iadanza, Carla; De Nigris, Bruno

2016-04-01

The "Major Project Pompeii" (MPP) is a great collective commitment of different institututions and people to set about solving the serious problem of conservation of the largest archeological sites in the world. The ancient city of Pompeii with its 66 hectares, 44 of which are excaveted, is divided into 9 regiones (district), subdivided in 118 insulae (blocks) and almost 1500 domus (houses), and is Unesco site since 1996. The Italian Ministry for Heritage and Cultural Activities and Tourism (MiBACT) and Finmeccanica Group have sealed an agreement whereby the Finmeccanica Group will donate innovative technologies and services for monitoring and protecting the archaeological site of Pompeii. Moreover, the Italian Institute for Environment Protection and Research (ISPRA) - Geological Survey of Italy, was also involved to support the ground based analysis and interpretation of the measurements provided by the industrial team, in order to promote an interdisciplinary approach. In this work, we will focus on ground deformation measurements obtained by satellite SAR interferometry and on their interpretation. The satellite monitoring service is based on the processing of COSMO-SkyMed Himage data by the e-Geos proprietary Persistent Scatterer Pair (PSP) SAR interferometry technology. The PSP technique is a proven SAR interferometry method characterized by the fact of exploiting in the processing only the relative properties between close points (pairs) in order to overcome atmospheric artifacts (which are one of the main problems of SAR interferometry). Validations analyses showed that this technique applied to COSMO-SkyMed Himage data is able to retrieve very dense (except of course on vegetated or cultivated areas) millimetric deformation measurements with sub-metric localization. By means of the COSMO-SkyMed PSP SAR interferometry processing, a historical analysis of the ground and structure deformations occurred over the entire archaeological site of Pompeii in the period from 2010 to 2014 was initially performed. Moreover, the deformation monitoring is continuing with monthly updates of the PSP analysis with new COSMO-SkyMed acquisitions both in ascending and descending geometry. The first results of the preliminary analysis over the archaeological site of Pompeii did not show large areas affected by deformations. However, the COSMO-SkyMed PSP SAR interferometry analysis proved to be very efficient due to its capability of providing a large number of deformation measurements over the archaeological site and structures with relatively small impact and cost. Moreover, in areas affected by collapses in the recent past, deformations were detected. Recent instability processes, both for the unexcavated slopes and for the archaeological structures, have promoted this low-impact analysis, aimed at identifying deformation paths and to prevent sudden collapses. Finally, the results obtained from the satellite techniques, will be also used to implement and improve the ground based geotechnical monitoring and warning system recently installed in selected case studies. Cross analysis between interferometric results, meteorological data and historical data of the site (e.g. collapses, works, etc.) are in progress in order to define provisional model aiming at an early identification of areas subjected to potential instability.

Coordination of Cellular Dynamics Contributes to Tooth Epithelium Deformations

PubMed Central

Morita, Ritsuko; Kihira, Miho; Nakatsu, Yousuke; Nomoto, Yohei; Ogawa, Miho; Ohashi, Kazumasa; Mizuno, Kensaku; Tachikawa, Tetsuhiko; Ishimoto, Yukitaka; Morishita, Yoshihiro; Tsuji, Takashi

2016-01-01

The morphologies of ectodermal organs are shaped by appropriate combinations of several deformation modes, such as invagination and anisotropic tissue elongation. However, how multicellular dynamics are coordinated during deformation processes remains to be elucidated. Here, we developed a four-dimensional (4D) analysis system for tracking cell movement and division at a single-cell resolution in developing tooth epithelium. The expression patterns of a Fucci probe clarified the region- and stage-specific cell cycle patterns within the tooth germ, which were in good agreement with the pattern of the volume growth rate estimated from tissue-level deformation analysis. Cellular motility was higher in the regions with higher growth rates, while the mitotic orientation was significantly biased along the direction of tissue elongation in the epithelium. Further, these spatio-temporal patterns of cellular dynamics and tissue-level deformation were highly correlated with that of the activity of cofilin, which is an actin depolymerization factor, suggesting that the coordination of cellular dynamics via actin remodeling plays an important role in tooth epithelial morphogenesis. Our system enhances the understanding of how cellular behaviors are coordinated during ectodermal organogenesis, which cannot be observed from histological analyses. PMID:27588418

Temperature and field direction dependences of first-order reversal curve (FORC) diagrams of hot-deformed Nd-Fe-B magnets

NASA Astrophysics Data System (ADS)

Yomogita, Takahiro; Okamoto, Satoshi; Kikuchi, Nobuaki; Kitakami, Osamu; Sepehri-Amin, Hossein; Ohkubo, Tadakatsu; Hono, Kazuhiro; Akiya, Takahiro; Hioki, Keiko; Hattori, Atsushi

2018-02-01

First-order reversal curve (FORC) diagram has been previously adopted for the analyses of magnetization reversal process and/or quantitative evaluation of coercivity and interaction field dispersions in various magnetic samples. Although these kinds of information are valuable for permanent magnets, previously reported FORC diagrams of sintered Nd-Fe-B magnets exhibit very complicated patterns. In this paper, we have studied the FORC diagrams of hot-deformed Nd-Fe-B magnets under various conditions. Contrary to the previous reports on sintered Nd-Fe-B magnets, the FORC diagram of the hot-deformed Nd-Fe-B magnet exhibits a very simple pattern consisting of a strong spot and a weak line. From this FORC diagram pattern, it is revealed that the coercivity dispersion of the hot-deformed Nd-Fe-B magnets is surprisingly small. Moreover, this feature of the FORC diagram pattern is very robust and unaffected by changes in various conditions such as grain boundary diffusion process, temperature, and field direction, whereas these conditions significantly change the coercivity and the shape of magnetization curve. This fact indicates that the magnetization reversal process of the hot-deformed Nd-Fe-B magnets is almost unchanged against these conditions.

In-beam studies of sup 96 Zr and sup 98 Zr: Collective excitations

DOE Office of Scientific and Technical Information (OSTI.GOV)

Henry, E.A.; Meyer, R.A.; Aprahamian, A.

1988-04-18

Nearly two decades ago signatures of deformation in the ground state bands of {sup 100}Zr and {sup 102}Zr were identified, and the rapid change in the deformation of heavy zirconium nuclei noted. It is now well accepted that the short-range proton-neutron interaction between the 1g{sub 9/2} and 1g{sub 7/2} spin-orbit partners plays an important role in producing ground state deformation in this region. Nevertheless, recent studies of zirconium nuclei, including those in the transition region, continue to refine our understanding of the interplay between single-particle and collective degrees of freedom. In this report we discuss some aspects of the levelmore » structures of {sup 96}Zr and {sup 98}Zr with emphasis on collective excitations. 18 refs., 2 tabs.« less

Gravity and magma induces spreading of Mount Etna volcano revealed by satellite radar interferometry

NASA Technical Reports Server (NTRS)

Lungren, P.; Casu, F.; Manzo, M.; Pepe, A.; Berardino, P.; Sansosti, E.; Lanari, R.

2004-01-01

Mount Etna underwent a cycle of eruptive activity over the past ten years. Here we compute ground displacement maps and deformation time series from more than 400 radar interferograms to reveal Mount Etna's average and time varying surface deformation from 1992 to 2001.

Apparatus for mounting a diode in a microwave circuit

DOEpatents

Liu, Shing-gong

1976-07-27

Apparatus for mounting a diode in a microwave circuit for making electrical contact between the circuit and ground and for dissipation of heat between the diode and a heat sink. The diode, supported on a thermally and electrically conductive member, is resiliently pressed in electrical contact with the microwave circuit. A tapered collar on the member is elastically deformably wedged into a tapered aperture formed in a heat sink. The wedged collar tightens firmly around the member establishing good thermal and electrical conduction from the diode to the heat sink and ground. Disassembly is facilitated because of the elastically deformed collar.

Intraplate Crustal Deformation Within the Northern Sinai Microplate: Evidence from Paleomagnetic Directions and Mechanical Modeling

NASA Astrophysics Data System (ADS)

Dembo, N.; Granot, R.; Hamiel, Y.

2017-12-01

The intraplate crustal deformation found in the northern part of the Sinai Microplate, located near the northern Dead Sea Fault plate boundary, is examined. Previous studies have suggested that distributed deformation in Lebanon is accommodated by regional uniform counterclockwise rigid block rotations. However, remanent magnetization directions observed near the Lebanese restraining bend are not entirely homogeneous suggesting that an unexplained and complex internal deformation pattern exists. In order to explain the variations in the amount of vertical-axis rotations we construct a mechanical model of the major active faults in the region that simulates the rotational deformation induced by motion along these faults. The rotational pattern calculated by the mechanical modeling predicts heterogeneous distribution of rotations around the faults. The combined rotation field that considers both the fault induced rotations and the already suggested regional block rotations stands in general agreement with the observed magnetization directions. Overall, the modeling results provide a more detailed and complete picture of the deformation pattern in this region and show that rotations induced by motion along the Dead Sea Fault act in parallel to rigid block rotations. Finally, the new modeling results unravel important insights as to the fashion in which crustal deformation is distributed within the northern part of the Sinai Microplate and propose an improved deformational mechanism that might be appropriate for other plate margins as well.

Synthetic Aperture Radar Interferometry Analysis of Ground Deformation within the Coso Geothermal Site, California

NASA Astrophysics Data System (ADS)

Brawner, Erik

Earth's surface movement may cause as a potential hazard to infrastructure and people. Associated earthquake hazards pose a potential side effect of geothermal activity. Modern remote sensing techniques known as Interferometric Synthetic Aperture Radar (InSAR) can measure surface change with a high degree of precision to mm scale movements. Previous work has identified a deformation anomaly within the Coso Geothermal site in eastern California. Surface changes have not been analyzed since the 1990s, allowing a decade of geothermal production impact to occur since previously assessed. In this study, InSAR data was acquired and analyzed between the years 2005 and 2010. Acquired by the ENVISAT satellite from both ascending and descending modes. This provides an independent dataset from previous work. Incorporating data generated from a new sensor covering a more modern temporal study period. Analysis of this time period revealed a subsidence anomaly in correlation with the extents of the geothermal production area under current operation. Maximum subsidence rates in the region reached approximately 3.8 cm/yr. A similar rate assessed from previous work throughout the 1990s. The correlation of subsidence patterns suggests a linear source of deformation from measurements spanning multiple decades. Regions of subsidence branch out from the main anomaly to the North-Northeast and to the South where additional significant peaks of subsidence occurring. The extents of the deformation anomaly directly correlate with the dispersal of geothermal production well site locations. Depressurization within the geothermal system provides a leading cause to surface subsidence from excessive extraction of hydrothermal fluids. As a result of minimal reinjection of production fluids.

Tectonic Deformation Pattern along the Longmen Shan Fault Zone in Eastern Tibet: Insights from Focal Mechanisms of the Wenchuan and Lushan Earthquake Sequences, Southwestern China

NASA Astrophysics Data System (ADS)

Yi, G.; Vallage, A.; Klinger, Y.; Long, F.; Wang, S.

2017-12-01

760 ML≥3.5 aftershocks of the 2008 Wenchuan earthquake, the 2013 Lushan mainshock and its 87 ML≥3.5 aftershocks were selected to obtain focal mechanism solutions from CAP waveform inversion method (Zhu and Helmberger, 1996), along with strain rosette (Amelung and King, 1997) and Areal strain (As) (Vallage et al., 2014), we aimed to analyze the tectonic deformation pattern along the Longmen Shan (LMS) fault zone, southwestern China. The As values show that 93% compressional earthquakes for the Lushan sequence are of pure thrust for the southern segment of the LMS fault zone, while only 50% compressional and nearly 40% of strike-slip and oblique-thrust events for the Wenchuan sequence reflect the strike-slip component increase on the central-northern segment of the LMS fault zone, meaning many different faults responsible for the Wenchuan aftershock activity. The strain rosettes with purely NW-trending compressional white lobe for the entire 87 aftershocks and 4 different classes of magnitudes are very similar to that of the Lushan mainshock. We infer that the geological structures for the southern segment are of thrust faulting under NW compressional deformation. The strain rosettes exhibit self-similarity in terms of orientation and shape for all classes, reflecting that the deformation pattern of the southern segment is independent with earthquake size, and suggesting that each class is representative of the overall deformation for the southern segment. We obtained EW-oriented pure compressional strain rosette of the entire 760 aftershocks and NW-oriented white lobe with small NE-oriented black lobe of the Wenchuan mainshock, and this difference may reflect different tectonic deformation pattern during the co-seismic and post-seismic stages. The deformation segmentation along the Wenchuan coseismic surface rupture is also evidenced from the different orientation of strain rosettes, i.e., NW for the southern area, NE for the central and NNW for the northern parts. The above inferences indicate a very complicated tectonic deformation pattern related to the complex geological structure. The segment of the northern aftershock area without ruptures behaves an oblique compressional deformation.

Quantifying near-field and off-fault deformation patterns of the 1992 Mw 7.3 Landers earthquake

NASA Astrophysics Data System (ADS)

Milliner, Christopher W. D.; Dolan, James F.; Hollingsworth, James; Leprince, Sebastien; Ayoub, Francois; Sammis, Charles G.

2015-05-01

Coseismic surface deformation in large earthquakes is typically measured using field mapping and with a range of geodetic methods (e.g., InSAR, lidar differencing, and GPS). Current methods, however, either fail to capture patterns of near-field coseismic surface deformation or lack preevent data. Consequently, the characteristics of off-fault deformation and the parameters that control it remain poorly understood. We develop a standardized method to fully measure the surface, near-field, coseismic deformation patterns at high resolution using the COSI-Corr program by correlating pairs of aerial photographs taken before and after the 1992 Mw 7.3 Landers earthquake. COSI-Corr offers the advantage of measuring displacement across the entire zone of surface deformation and over a wider aperture than that available to field geologists. For the Landers earthquake, our measured displacements are systematically larger than the field measurements, indicating the presence of off-fault deformation. We show that 46% of the total surface displacement occurred as off-fault deformation, over a mean deformation width of 154 m. The magnitude and width of off-fault deformation along the rupture is primarily controlled by the macroscopic structural complexity of the fault system, with a weak correlation with the type of near-surface materials through which the rupture propagated. Both the magnitude and width of distributed deformation are largest in stepovers, bends, and at the southern termination of the surface rupture. We find that slip along the surface rupture exhibits a consistent degree of variability at all observable length scales and that the slip distribution is self-affine fractal with dimension of 1.56.

Evaluating Topographic Effects on Ground Deformation: Insights from Finite Element Modeling

NASA Astrophysics Data System (ADS)

Ronchin, Erika; Geyer, Adelina; Martí, Joan

2015-07-01

Ground deformation has been demonstrated to be one of the most common signals of volcanic unrest. Although volcanoes are commonly associated with significant topographic relief, most analytical models assume the Earth's surface as flat. However, it has been confirmed that this approximation can lead to important misinterpretations of the recorded surface deformation data. Here we perform a systematic and quantitative analysis of how topography may influence ground deformation signals generated by a spherical pressure source embedded in an elastic homogeneous media and how these variations correlate with the different topographic parameters characterizing the terrain form (e.g., slope, aspect, curvature). For this, we bring together the results presented in previous published papers and complement them with new axisymmetric and 3D finite element (FE) model results. First, we study, in a parametric way, the influence of a volcanic edifice centered above the pressure source axis. Second, we carry out new 3D FE models simulating the real topography of three different volcanic areas representative of topographic scenarios common in volcanic regions: Rabaul caldera (Papua New Guinea) and the volcanic islands of Tenerife and El Hierro (Canary Islands). The calculated differences are then correlated with a series of topographic parameters. The final aim is to investigate the artifacts that might arise from the use of half-space models at volcanic areas due to diverse topographic features (e.g., collapse caldera structures, prominent central edifices, large landslide scars).

Ground deformation monitoring using RADARSAT-2 DInSAR-MSBAS at the Aquistore CO2 storage site in Saskatchewan (Canada)

NASA Astrophysics Data System (ADS)

Czarnogorska, M.; Samsonov, S.; White, D.

2014-11-01

The research objectives of the Aquistore CO2 storage project are to design, adapt, and test non-seismic monitoring methods for measurement, and verification of CO2 storage, and to integrate data to determine subsurface fluid distributions, pressure changes and associated surface deformation. Aquistore site is located near Estevan in Southern Saskatchewan on the South flank of the Souris River and west of the Boundary Dam Power Station and the historical part of Estevan coal mine in southeastern Saskatchewan, Canada. Several monitoring techniques were employed in the study area including advanced satellite Differential Interferometric Synthetic Aperture Radar (DInSAR) technique, GPS, tiltmeters and piezometers. The targeted CO2 injection zones are within the Winnipeg and Deadwood formations located at > 3000 m depth. An array of monitoring techniques was employed in the study area including advanced satellite Differential Interferometric Synthetic Aperture Radar (DInSAR) with established corner reflectors, GPS, tiltmeters and piezometers stations. We used airborne LIDAR data for topographic phase estimation, and DInSAR product geocoding. Ground deformation maps have been calculated using Multidimensional Small Baseline Subset (MSBAS) methodology from 134 RADARSAT-2 images, from five different beams, acquired during 20120612-20140706. We computed and interpreted nine time series for selected places. MSBAS results indicate slow ground deformation up to 1 cm/year not related to CO2 injection but caused by various natural and anthropogenic causes.

PSI Analysis of Ground Deformations Along the South-Western Coast of the Gulf of Gdansk (Poland)

NASA Astrophysics Data System (ADS)

Czarnogorska, Magdalena; Graniczny, Marek; Uscinowicz, Szymon; Nutricato, Raffaele; Triggiani, Saverio; Nitti, David Oscar; Bovenga, Fabio; Wasowski, Janusz

2010-03-01

We use over 40 descending ERS-1/2 SLC (Frame = 2511 , Track = 36) images from the period 1995 - 2001 and the SPINUA (Stable Point Interferometry over Un- urbanised Areas) Persistent Scatterers Interferometry (PSI) processing technique to study Earth surface deformations along the SW coast of the Gulf of Gdansk, along the SE part of the Baltic Sea.The area of interest (AOI) includes few cities and several towns, villages and harbours. The low lying coastal areas of the SW part of the Gulf of Gdansk are at risk of floods and marine erosion. It is expected that this problem can be exacerbated by the ongoing sea level rise and possibly by crustal movements (subsidence) reported in the literature.The PSI results, however, did not reveal the presence of a regional scale, spatially consistent pattern of displacements. It is likely that any crustal deformations in the AOI simply do not exceed +-2 mm/year, which is the velocity threshold we assumed to distinguish between moving and non-moving radar targets. Nevertheless, significant downward displacements, amounting to several mm/year, are locally present in the coastal zone east of Gdansk that belongs to the Vistula river delta-alluvial plain system, as well as in the inland area west of the cities of Gdansk and Sopot. It is apparent that in all these cases the movements reflect mainly differential settlements of buildings and engineering infrastructure, which have recently been built in the areas including clay-rich, compressible sediments. Indeed, one of the highest subsidence rates (- 12 mm/year) was observed in the Gdansk petroleum refinery constructed on alluvial sediments. Thus the anthropogenic loading and consolidation of the recent deposits can locally be an important factor causing ground settlements. Importantly, for the most part the urban areas of the main cities (Gdansk, Gdynia and Sopot) result to be stable.

Forecasting the Onset Time of Volcanic Eruptions Using Ground Deformation Data

NASA Astrophysics Data System (ADS)

Blake, S.; Cortes, J. A.

2016-12-01

The pre-eruptive inflation of the ground surface is a well-known phenomenon at many volcanoes. In a number of intensively studied cases, elevation and/or radial tilt increase with time (t) towards a limiting value by following a decaying exponential with characteristic timescale τ (Kilauea and Mauna Loa: Dvorak and Okamura 1987, Lengliné et al., 2008) or, after sufficiently long times, by following the sum of two such functions such that two timescales, τ1 and τ2, are required to describe the temporal pattern of inflation (Axial Seamount: Nooner and Chadwick, 2009). We have used the Levenberg-Marquardt non-linear fit algorithm to analyse data for 18 inflation periods at Krafla volcano, Iceland, (Björnsson and Eysteinsson, 1998) and found the same functional relationship. Pooling all of the available data from 25 eruptions at 4 volcanoes shows that the duration of inflation before an eruption or shallow intrusion (t*) is comparable to τ (or the longer of τ1 and τ2) and follows an almost 1:1 linear relationship (r2 0.8). We also find that this scaling is replicated by Monte Carlo simulations of physics-based forward models of hydraulically connected dual magma chamber systems which erupt when the chamber pressure reaches a threshold value. These results lead to a new forecasting method which we describe and assess here: if τ can be constrained during an on-going inflation period, then the statistical distribution of t*/τ values calibrated from other pre-eruptive inflation periods allows the probability of an eruption starting before (or after) a specified time to be estimated. The time at which there is a specified probability of an eruption starting can also be forecast. These approaches rely on fitting deformation data up to time t in order to obtain τ(t) which is then used to forecast t*. Forecasts can be updated after each new deformation measurement.

The 2011 volcanic crisis at El Hierro (Canary Islands): monitoring ground deformation through tiltmeter and gravimetric observations

NASA Astrophysics Data System (ADS)

Arnoso, J.; Montesinos, F. G.; Benavent, M.; Vélez, E. J.

2012-04-01

El Hierro is an ocean island located at the western end of the Canary Islands, and along with Tenerife and La Palma islands have been the most geologically active in the recent past. The island has a triple armed rift and, presently, is at the stage of growth, representing the summit of a volcanic shield elevating from the seafloor at depth of 4000 m up to 1501 m above the sea level (Münn et al., 2006; Carracedo et al., 1999). Since July 19th, 2011 seismic activity has produced more than 11950 events up to date. The seismic crisis resulted in a volcanic eruption that began on October 10th, being still currently active. The new volcano is located 2 km off the coast and about 300 m depth, in the submarine flank of the southern rift of the island, which is extended some 40 km length. Since September 2004 until November 2010 two continuous tilt stations were installed at the north, Balneario site (BA), and at the center of the island, Aula de la Naturaleza (AU) site. Both stations were used to assess the pattern of local ground movements in the island. When seismic swarm started on past July 2011, we have reinstalled both tilt stations (BA and AU) and 2 new ones located at the south of the island, namely Montaña Quemada (MQ) and Restinga (RE) sites. We have used short base platform tiltmeters that measure ground tilts with resolutions varying from 0.1 up to 0.01 microradians (µrad). On October 8th, a 4.4 magnitude earthquake took place and is supposed that fractured the ocean crust at some 8-10 km off the south coast of the island and about 1000 m depth. Typical spike signals were observed at the tilt stations. Two days after, the eruption onset was recorded also at tilt stations through a remarkable increase of the high frequency signal, being of large amplitude the components (radial) orientated towards the new volcano edifice. When compared with previous tiltmeter records in the island, tilt pattern were clearly modified several times at the stations when strong and shallow earthquakes happened, producing in some cases large tilt variations of tens of µrad. By other side, in 2003 we established a control gravity network that was measured again in 2004 and 2008. After the beginning of the eruption on October 2011, we have carried out gravity measurements in various points of the network as well as other new points to attain more accurate control of the possible variations of gravity or/and altitude. Gravity data are still under study although some results about observed gravity changes could reflect the ground deformations pattern according to tiltmeter records and GPS measurements, or a change in the subsurface mass distribution as consequence of the new emplacement the magmatic material in the area with volcanic and seismic activity.

Loading Deformation Characteristic Simulation Study of Engineering Vehicle Refurbished Tire

NASA Astrophysics Data System (ADS)

Qiang, Wang; Xiaojie, Qi; Zhao, Yang; Yunlong, Wang; Guotian, Wang; Degang, Lv

2018-05-01

The paper constructed engineering vehicle refurbished tire computer geometry model, mechanics model, contact model, finite element analysis model, did simulation study on load-deformation property of engineering vehicle refurbished tire by comparing with that of the new and the same type tire, got load-deformation of engineering vehicle refurbished tire under the working condition of static state and ground contact. The analysis result shows that change rules of radial-direction deformation and side-direction deformation of engineering vehicle refurbished tire are close to that of the new tire, radial-direction and side-direction deformation value is a little less than that of the new tire. When air inflation pressure was certain, radial-direction deformation linear rule of engineer vehicle refurbished tire would increase with load adding, however, side-direction deformation showed linear change rule, when air inflation pressure was low; and it would show increase of non-linear change rule, when air inflation pressure was very high.

Single-particle and collective motion in unbound deformed 39Mg

NASA Astrophysics Data System (ADS)

Fossez, K.; Rotureau, J.; Michel, N.; Liu, Quan; Nazarewicz, W.

2016-11-01

Background: Deformed neutron-rich magnesium isotopes constitute a fascinating territory where the interplay between collective rotation and single-particle motion is strongly affected by the neutron continuum. The unbound f p -shell nucleus 39Mg is an ideal candidate to study this interplay. Purpose: In this work, we predict the properties of low-lying resonant states of 39Mg, using a suite of realistic theoretical approaches rooted in the open quantum system framework. Method: To describe the spectrum and decay modes of 39Mg we use the conventional shell model, Gamow shell model, resonating group method, density matrix renormalization group method, and the nonadiabatic particle-plus-rotor model formulated in the Berggren basis. Results: The unbound ground state of 39Mg is predicted to be either a Jπ=7/2 - state or a 3/2 - state. A narrow Jπ=7/2 - ground-state candidate exhibits a resonant structure reminiscent of that of its one-neutron halo neighbor 37Mg, which is dominated by the f7 /2 partial wave at short distances and a p3 /2 component at large distances. A Jπ=3/2 - ground-state candidate is favored by the large deformation of the system. It can be associated with the 1/2 -[321 ] Nilsson orbital dominated by the ℓ =1 wave; hence its predicted width is large. The excited Jπ=1/2 - and 5 /2- states are expected to be broad resonances, while the Jπ=9/2 - and 11/2 - members of the ground-state rotational band are predicted to have very small neutron decay widths. Conclusion: We demonstrate that the subtle interplay between deformation, shell structure, and continuum coupling can result in a variety of excitations in an unbound nucleus just outside the neutron drip line.

Monitoring of surface movement in a large area of the open pit iron mines (Carajás, Brazil) based on A-DInSAR techniques using TerraSAR-X data

NASA Astrophysics Data System (ADS)

Mura, José C.; Paradella, Waldir R.; Gama, Fabio F.; Silva, Guilherme G.

2016-10-01

PSI (Persistent Scatterer Interferometry) analysis of large area is always a challenging task regarding the removal of the atmospheric phase component. This work presents an investigation of ground deformation measurements based on a combination of DInSAR Time-Series (DTS) and PSI techniques, applied in a large area of open pit iron mines located in Carajás (Brazilian Amazon Region), aiming at detect high rates of linear and nonlinear ground deformation. These mines have presented a historical of instability and surface monitoring measurements over sectors of the mines (pit walls) have been carried out based on ground based radar and total station (prisms). By using a priori information regarding the topographic phase error and phase displacement model derived from DTS, temporal phase unwrapping in the PSI processing and the removal of the atmospheric phases can be performed more efficiently. A set of 33 TerraSAR-X-1 images, acquired during the period from March 2012 to April 2013, was used to perform this investigation. The DTS analysis was carried out on a stack of multi-look unwrapped interferogram using an extension of SVD to obtain the Least-Square solution. The height errors and deformation rates provided by the DTS approach were subtracted from the stack of interferogram to perform the PSI analysis. This procedure improved the capability of the PSI analysis to detect high rates of deformation as well as increased the numbers of point density of the final results. The proposed methodology showed good results for monitoring surface displacement in a large mining area, which is located in a rain forest environment, providing very useful information about the ground movement for planning and risks control.

4D imaging of the source of ground deformation at Campi Flegrei caldera (Italy) during recent unrest episodes

NASA Astrophysics Data System (ADS)

D'Auria, L.; Giudicepietro, F.; Martini, M.; Lanari, R.

2011-12-01

Campi Flegrei caldera, has been affected in recent decades by three episodes of significant ground uplift. After the last crisis (1982-84), which was accompanied by strong seismicity, the ground has shown a general descending trend, occasionally interrupted by minor uplift episodes, together with low-magnitude volcano-tectonic and long-period seismicity. We assume that the source of minor ground deformations consists in a diffuse volumetric source, related to both thermoelastic and poroelastic strain. This is a reasonable assumption considering that Campi Flegrei are known to host a geothermal reservoir. We have inverted a DInSAR dataset spanning the interval 1995-2008. Results show that the geometry of the source is much more complex than previously recognized and, most important, it shows significant temporal variations, within few months. The deformation source, of the analyzed uplift episodes, starts with a volumetric expansion centered at a depth of about 5 km. The position of this volume is close to the caldera rims. Later the expansion migrates upward, reaching the surface along preferred paths, leading to the Solfatara area, located almost at the center of the caldera. This area is well known for its powerful geothermal emissions. During the upward migration, seismic long-period sources are activated. Their location is consistent with the path identified by the inversion of the DInSAR dataset. We infer, that this dynamics is linked to the injection of hot fluid batches, along the caldera rims and their upward migration, following preferential high permeability paths. Furthermore we have identified an injection episode which has not been previously recognized. The deformation source remains at depth slowly waning in few years. We show how this conceptual framework fits well with the observed geodetic, seismic and geochemical data.

A GPU based high-resolution multilevel biomechanical head and neck model for validating deformable image registration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Neylon, J., E-mail: jneylon@mednet.ucla.edu; Qi, X.; Sheng, K.

Purpose: Validating the usage of deformable image registration (DIR) for daily patient positioning is critical for adaptive radiotherapy (RT) applications pertaining to head and neck (HN) radiotherapy. The authors present a methodology for generating biomechanically realistic ground-truth data for validating DIR algorithms for HN anatomy by (a) developing a high-resolution deformable biomechanical HN model from a planning CT, (b) simulating deformations for a range of interfraction posture changes and physiological regression, and (c) generating subsequent CT images representing the deformed anatomy. Methods: The biomechanical model was developed using HN kVCT datasets and the corresponding structure contours. The voxels inside amore » given 3D contour boundary were clustered using a graphics processing unit (GPU) based algorithm that accounted for inconsistencies and gaps in the boundary to form a volumetric structure. While the bony anatomy was modeled as rigid body, the muscle and soft tissue structures were modeled as mass–spring-damper models with elastic material properties that corresponded to the underlying contoured anatomies. Within a given muscle structure, the voxels were classified using a uniform grid and a normalized mass was assigned to each voxel based on its Hounsfield number. The soft tissue deformation for a given skeletal actuation was performed using an implicit Euler integration with each iteration split into two substeps: one for the muscle structures and the other for the remaining soft tissues. Posture changes were simulated by articulating the skeletal structure and enabling the soft structures to deform accordingly. Physiological changes representing tumor regression were simulated by reducing the target volume and enabling the surrounding soft structures to deform accordingly. Finally, the authors also discuss a new approach to generate kVCT images representing the deformed anatomy that accounts for gaps and antialiasing artifacts that may be caused by the biomechanical deformation process. Accuracy and stability of the model response were validated using ground-truth simulations representing soft tissue behavior under local and global deformations. Numerical accuracy of the HN deformations was analyzed by applying nonrigid skeletal transformations acquired from interfraction kVCT images to the model’s skeletal structures and comparing the subsequent soft tissue deformations of the model with the clinical anatomy. Results: The GPU based framework enabled the model deformation to be performed at 60 frames/s, facilitating simulations of posture changes and physiological regressions at interactive speeds. The soft tissue response was accurate with a R{sup 2} value of >0.98 when compared to ground-truth global and local force deformation analysis. The deformation of the HN anatomy by the model agreed with the clinically observed deformations with an average correlation coefficient of 0.956. For a clinically relevant range of posture and physiological changes, the model deformations stabilized with an uncertainty of less than 0.01 mm. Conclusions: Documenting dose delivery for HN radiotherapy is essential accounting for posture and physiological changes. The biomechanical model discussed in this paper was able to deform in real-time, allowing interactive simulations and visualization of such changes. The model would allow patient specific validations of the DIR method and has the potential to be a significant aid in adaptive radiotherapy techniques.« less

Pattern size tolerance of reverse offset printing: a proximity deformation effect related to local PDMS slipping

NASA Astrophysics Data System (ADS)

Kusaka, Yasuyuki; Kanazawa, Shusuke; Koutake, Masayoshi; Ushijima, Hirobumi

2017-10-01

We investigated the shape integrity of silver nanoparticle ink patterns formed by reverse offset printing, focusing particularly on the proximity effect of neighbouring patterns due to the local deformation of a polydimethylsiloxane (PDMS) blanket during contact with a hard cliché. We performed printing tests using a cliché having circular patterns with smaller neighbouring circles located at various distances (2-20 µm), and the results revealed that as we decrease the thickness of PDMS and the inter-pattern gap distance, and as we increase the printing indentations, the shape integrity of the printed pattern was worsened. A complementary numerical simulation of PDMS deformations suggested that the pattern distortion during the contact with clichés was caused by the horizontal deformation of PDMS during the printing, which becomes a significant burden when the uplifted region of PDMS is closer to the gap distance of each pattern. Our analysis further indicates that during printing, there is slipping of the ink at the PDMS interface. In addition, we examined the effects of a synchronization mismatch in a roll-to-sheet printing on the pattern size tolerance. The magnitude of the size distortions was severely influenced not only by the mismatch ratio but also by the nip width. This result verifies the scraping of the ink accompanied by the slipping of the PDMS during the printing process, and thereby determines the size tolerance of printed patterns in reverse offset printing. Finally, we discuss the optimization of process parameters to ensure the size integrity of reverse offset printing.

Grounding the figure.

PubMed

Calis, G; Leeuwenberg, E

1981-12-01

Coding rules can be formulated in which the shortest description of a figure-ground pattern exhibits a hierarchical structure, with the ground playing a primary and the figure a secondary role. We hypothesized that the process of perception involves and assimilation phase followed by a test phase in which the ground is tested before the figure. Experiments are described in which pairs of consecutive, superimposed patterns are presented in rapid succession, resulting in a subjective impression of seeing one pattern only. In these presentations, the second pattern introduces some deliberate distortion of the figure or ground displayed in the first pattern. Maximal distortions of the ground occur at shorter stimulus onset asynchronies than maximal distortions of the figure, suggesting that the ground codes are processed before figure codes. Moreover, patterns presenting the ground first are more likely to be perceived as ground, regardless of the distortions, than patterns presenting the figure first. This quasi masking or microgenetic approach might be relevant to theories on :mediations of immediate, or direct" perception.

Cephalopod-inspired design of electro-mechano-chemically responsive elastomers for on-demand fluorescent patterning

NASA Astrophysics Data System (ADS)

Wang, Qiming; Gossweiler, Gregory R.; Craig, Stephen L.; Zhao, Xuanhe

2014-09-01

Cephalopods can display dazzling patterns of colours by selectively contracting muscles to reversibly activate chromatophores - pigment-containing cells under their skins. Inspired by this novel colouring strategy found in nature, we design an electro-mechano-chemically responsive elastomer system that can exhibit a wide variety of fluorescent patterns under the control of electric fields. We covalently couple a stretchable elastomer with mechanochromic molecules, which emit strong fluorescent signals if sufficiently deformed. We then use electric fields to induce various patterns of large deformation on the elastomer surface, which displays versatile fluorescent patterns including lines, circles and letters on demand. Theoretical models are further constructed to predict the electrically induced fluorescent patterns and to guide the design of this class of elastomers and devices. The material and method open promising avenues for creating flexible devices in soft/wet environments that combine deformation, colorimetric and fluorescent response with topological and chemical changes in response to a single remote signal.

SU-F-P-54: Guidelines to Check Image Registration QA of a Clinical Deformation Registration Software: A Single Institution Preliminary Study

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gill, G; Souri, S; Rea, A

Purpose: The objective of this study is to verify and analyze the accuracy of a clinical deformable image registration (DIR) software. Methods: To test clinical DIR software qualitatively and quantitatively, we focused on lung radiotherapy and analyzed a single (Lung) patient CT scan. Artificial anatomical changes were applied to account for daily variations during the course of treatment including the planning target volume (PTV) and organs at risk (OAR). The primary CT (pCT) and the structure set (pST) was deformed with commercial tool (ImSimQA-Oncology Systems Limited) and after artificial deformation (dCT and dST) sent to another commercial tool (VelocityAI-Varian Medicalmore » Systems). In Velocity, the deformed CT and structures (dCT and dST) were inversely deformed back to original primary CT (dbpCT and dbpST). We compared the dbpST and pST structure sets using similarity metrics. Furthermore, a binary deformation field vector (BDF) was created and sent to ImSimQA software for comparison with known “ground truth” deformation vector fields (DVF). Results: An image similarity comparison was made by using “ground truth” DVF and “deformed output” BDF with an output of normalized “cross correlation (CC)” and “mutual information (MI)” in ImSimQA software. Results for the lung case were MI=0.66 and CC=0.99. The artificial structure deformation in both pST and dbpST was analyzed using DICE coefficient, mean distance to conformity (MDC) and deformation field error volume histogram (DFEVH) by comparing them before and after inverse deformation. We have noticed inadequate structure match for CTV, ITV and PTV due to close proximity of heart and overall affected by lung expansion. Conclusion: We have seen similarity between pCT and dbpCT but not so well between pST and dbpST, because of inadequate structure deformation in clinical DIR system. This system based quality assurance test will prepare us for adopting the guidelines of upcoming AAPM task group 132 protocol.« less

The Relation Between Rotation Deformity and Nerve Root Stress in Lumbar Scoliosis

NASA Astrophysics Data System (ADS)

Kim, Ho-Joong; Lee, Hwan-Mo; Moon, Seong-Hwan; Chun, Heoung-Jae; Kang, Kyoung-Tak

Even though several finite element models of lumbar spine were introduced, there has been no model including the neural structure. Therefore, the authors made the novel lumbar spine finite element model including neural structure. Using this model, we investigated the relation between the deformity pattern and nerve root stress. Two lumbar models with different types of curve pattern (lateral bending and lateral bending with rotation curve) were made. In the model of lateral bending curves without rotation, the principal compressive nerve root stress on the concave side was greater than the principal tensile stress on the convex side at the apex vertebra. Contrarily, in the lateral bending curve with rotational deformity, the nerve stress on the convex side was higher than that on the concave side. Therefore, this study elicit that deformity pattern could have significantly influence on the nerve root stress in the lumbar spine.

Breaks in Pavement and Pipes as Indicators of Range-Front Faulting Resulting from the 1989 Loma Prieta Earthquake near the Southwest Margin of the Santa Clara Valley, California

USGS Publications Warehouse

Schmidt, Kevin M.; Ellen, Stephen D.; Haugerud, Ralph A.; Peterson, David M.; Phelps, Geoffery A.

1995-01-01

Damage to pavement and near-surface utility pipes, caused by the October 17, 1989, Loma Prieta earthquake, provide indicators for ground deformation in a 663 km2 area near the southwest margin of the Santa Clara Valley, California. The spatial distribution of 1284 sites of such damage documents the extent and distribution of detectable ground deformation. Damage was concentrated in four zones, three of which are near previously mapped faults. The zone through Los Gatos showed the highest concentration of damage, as well as evidence for pre- and post-earthquake deformation. Damage along the foot of the Santa Cruz Mountains reflected shortening that is consistent with movement along reverse faults in the region and with the hypothesis that tectonic strain is distributed widely across numerous faults in the California Coast Ranges.

Multi-instrument observations of pre-earthquake transient signatures associated with 2015 M8.3 Chile earthquake

NASA Astrophysics Data System (ADS)

Ouzounov, D.; Pulinets, S. A.; Hernandez-Pajares, M.; Garcia-Rigo, A.; De Santis, A.; Pavón, J.; Liu, J. Y. G.; Chen, C. H.; Cheng, K. C.; Hattori, K.; Stepanova, M. V.; Romanova, N.; Hatzopoulos, N.; Kafatos, M.

2016-12-01

We are conducting multi parameter validation study on lithosphere/atmosphere /ionosphere transient phenomena preceding major earthquakes particularly for the case of M8.3 of Sept 16th, 2015 in Chile. Our approach is based on monitoring simultaneously a series of different physical parameters from space: 1/Outgoing long-wavelength radiation (OLR obtained from NOAA/AVHRR); 2/ electron and electron density variations in the ionosphere via GPS Total Electron Content (GPS/TEC), and 3/geomagnetic field and plasma density variation (Swarm); and from ground: 3/ GPS crustal deformation and 4/ground-based magnetometers. The time and location of main shock was prospectively alerted in advance using the Multi Sensor Networking Approach (MSNA-LAIC) approach. We analyzed retrospectively several physical observations characterizing the state of the lithosphere, atmosphere and ionosphere several days before, during and after the M8.3 earthquakes in Illapel. Our continuous satellite monitoring of long-wave (LW) data over Chile, shows a rapid increase of emitted radiation during the end of August 2015 and an anomaly in the atmosphere was detected at 19 LT on Sept 1st, 2015, over the water near to the epicenter. On Sept 2nd Swarm magnetic measurements show an anomalous signature over the epicentral region. GPS/TEC analysis revealed an anomaly on Sept 14th and on the same day the degradation of Equatorial Ionospheric Anomaly (EIA) and disappearance of the crests of EIA as is characteristic for pre-dawn and early morning hours (11 LT) was observed. On Sept 16th co-seismic ionospheric signatures consistent with defined circular acoustic-gravity wave and different shock-acoustic waves were also observed. GPS TEC and deformation studies were computed from 48 GPS stations (2013-2015) of National Seismological Center of Chile (CSN) GPS network. A transient signal of deformation has been observed a week in advance correlated with ground-based magnetometers ULF signal fluctuation from closest to the epicenter station from the SAMBA-AMBER network. The characteristics of the observed pre-, and co - seismic transient signals associated with the M8.3 of Illapel, Chile 2015 earthquake suggested that they follow general temporal-spatial evolution pattern, which has been seen in other large earthquakes worldwide.

10 CFR 100.23 - Geologic and seismic siting criteria.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Earthquake Ground Motion, and to permit adequate engineering solutions to actual or potential geologic and..., earthquake recurrence rates, fault geometry and slip rates, site foundation material, and seismically induced... Earthquake Ground Motion for the site, the potential for surface tectonic and nontectonic deformations, the...

10 CFR 100.23 - Geologic and seismic siting criteria.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Earthquake Ground Motion, and to permit adequate engineering solutions to actual or potential geologic and..., earthquake recurrence rates, fault geometry and slip rates, site foundation material, and seismically induced... Earthquake Ground Motion for the site, the potential for surface tectonic and nontectonic deformations, the...

10 CFR 100.23 - Geologic and seismic siting criteria.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Earthquake Ground Motion, and to permit adequate engineering solutions to actual or potential geologic and..., earthquake recurrence rates, fault geometry and slip rates, site foundation material, and seismically induced... Earthquake Ground Motion for the site, the potential for surface tectonic and nontectonic deformations, the...

Decrypting geophysical signals at Stromboli Volcano (Italy): Integration of seismic and Ground-Based InSAR displacement data

PubMed Central

Di Traglia, F; Cauchie, L; Casagli, N; Saccorotti, G

2014-01-01

We present the integration of seismic and Ground-Based Interferometric Synthetic Aperture Radar system (GBInSAR) displacement data at Stromboli Volcano. Ground deformation in the area of summit vents is positively correlated with both seismic tremor amplitude and cumulative amplitudes of very long period (VLP) signals associated with Strombolian explosions. Changes in VLP amplitudes precede by a few days the variations in ground deformation and seismic tremor. We propose a model where the arrival of fresh, gas-rich magma from depth enhances gas slug formation, promoting convection and gas transfer throughout the conduit system. At the shallowest portion of the conduit, an increase in volatile content causes a density decrease, expansion of the magmatic column and augmented degassing activity, which respectively induce inflation of the conduit, and increased tremor amplitudes. The temporal delay between increase of VLP and tremor amplitudes/conduit inflation can be interpreted in terms of the different timescales characterizing bulk gas transfer versus slug formation and ascent. PMID:25821278

Decrypting geophysical signals at Stromboli Volcano (Italy): Integration of seismic and Ground-Based InSAR displacement data.

PubMed

Di Traglia, F; Cauchie, L; Casagli, N; Saccorotti, G

2014-04-28

We present the integration of seismic and Ground-Based Interferometric Synthetic Aperture Radar system (GBInSAR) displacement data at Stromboli Volcano. Ground deformation in the area of summit vents is positively correlated with both seismic tremor amplitude and cumulative amplitudes of very long period (VLP) signals associated with Strombolian explosions. Changes in VLP amplitudes precede by a few days the variations in ground deformation and seismic tremor. We propose a model where the arrival of fresh, gas-rich magma from depth enhances gas slug formation, promoting convection and gas transfer throughout the conduit system. At the shallowest portion of the conduit, an increase in volatile content causes a density decrease, expansion of the magmatic column and augmented degassing activity, which respectively induce inflation of the conduit, and increased tremor amplitudes. The temporal delay between increase of VLP and tremor amplitudes/conduit inflation can be interpreted in terms of the different timescales characterizing bulk gas transfer versus slug formation and ascent.

Geodetic Volcano Monitoring Research in Canary Islands: Recent Results

NASA Astrophysics Data System (ADS)

Fernandez, J.; Gonzalez, P. J.; Arjona, A.; Camacho, A. G.; Prieto, J. F.; Seco, A.; Tizzani, P.; Manzo, M. R.; Lanari, R.; Blanco, P.; Mallorqui, J. J.

2009-05-01

The Canarian Archipelago is an oceanic island volcanic chain with a long-standing history of volcanic activity (> 40 Ma). It is located off the NW coast of the African continent, lying over a transitional crust of the Atlantic African passive margin. At least 12 eruptions have been occurred on the islands of Lanzarote, Tenerife and La Palma in the last 500 years. Volcanism manifest predominantly as basaltic strombolian monogenetic activity (whole archipelago) and central felsic volcanism (active only in Tenerife Island). We concentrate our studies in the two most active islands, Tenerife and La Palma. In these islands, we tested different methodologies of geodetic monitoring systems. We use a combination of ground- and space-based techniques. At Tenerife Island, a differential interferometric study was performed to detect areas of deformation. DInSAR detected two clear areas of deformation, using this results a survey-based GPS network was designed and optimized to control those deformations and the rest of the island. Finally, using SBAS DInSAR results weak spatial long- wavelength subsidence signals has been detected. At La Palma, the first DInSAR analysis have not shown any clear deformation, so a first time series analysis was performed detecting a clear subsidence signal at Teneguia volcano, as for Tenerife a GPS network was designed and optimized taking into account stable and deforming areas. After several years of activities, geodetic results served to study ground deformations caused by a wide variety of sources, such as changes in groundwater levels, volcanic activity, volcano-tectonics, gravitational loading, etc. These results proof that a combination of ground-based and space-based techniques is suitable tool for geodetic volcano monitoring in Canary Islands. Finally, we would like to strength that those results could have serious implications on the continuous geodetic monitoring system design and implementation for the Canary Islands which is under development nowadays.

Conditions for Land Subsidence and Ground Failure in Lacustrine Sediments, the Case of West Chapala Basin.

NASA Astrophysics Data System (ADS)

Hernandez-Marin, M.; Pacheco, J.; Ortiz-Lozano, J. A.; Ramirez-Cortes, A.; Araiza, G.

2014-12-01

Surface deformation in the form of land subsidence and ground failure in the Chapala Basin has caused serious damage to structures, mostly homes. In this work, the conditions for the occurrence of deformation particularly regarding the physical and mechanical properties of the soil are discussed. In 2012 a maximum land subsidence of 7.16 cm in a short period of 8 months was recorded with maximum velocities of deformation close to 0.89 centimeters per month. Natural conditions of the zone of study include a lacustrine low land with the perennial Chapala Lake, surrounded by ranges formed by volcanic extrusive rocks, mostly basalts and andesites. Two soil cores of 11 meters depth show the predominance of fine soil but with the incrustation of several sandy lenses of volcanic ash. In the first core closer to the piedmont, the volcanic ash presents an accumulated thickness close to three meters, starting at 4.5 meters depth; on the contrary, this thickness in the second core closer to the lake is critically reduced to no more than 50 centimeters. Even though the predominance of fine soil is significant, water-content averages 100 % and the liquid limit is low, suggesting amongst other possibilities, low content of clay or at least low content of smectites or allophanes in the clayey portion. Other properties of the soil are being determined for analyses. The occurrence of three alignments of ground failures in the community of Jocotepec at the west, mostly faults, suggests highly heterogeneous subsoil. The high volumes of groundwater withdrawn from the local aquifers mainly for agriculture are directly contributing to the increase of the effective stress and surface deformation, however, the relationship between level descents and surficial deformation is still not clear.

Using LiCSAR as a fast-response system for the detection and the monitoring of volcanic unrest

NASA Astrophysics Data System (ADS)

Albino, F.; Biggs, J.; Hatton, E. L.; Spaans, K.; Gaddes, M.; McDougall, A.

2017-12-01

Based on the Smithsonian Institution volcano database, a total of 13256 volcanoes exist on Earth with 1273 having evidence of eruptive or unrest activity during the Holocene. InSAR techniques have proven their ability to detect and to quantify volcanic ground deformation on a case-by-case basis. However, the use of InSAR for the daily monitoring of every active volcano requires the development of automatic processing that can provide information in a couple of hours after a new radar acquisition. The LiCSAR system (http://comet.nerc.ac.uk/COMET-LiCS-portal/) answers this requirement by processing the vast amounts of data generated daily by the EU's Sentinel-1 satellite constellation. It provides now high-resolution deformation data for the entire Alpine-Himalayan seismic belt. The aim of our study is to extend LiCSAR system to the purpose of volcano monitoring. For each active volcano, the last Sentinel products calculated (phase, coherence and amplitude) will be available online in the COMET Volcano Deformation Database. To analyse this large amount of InSAR products, we develop an algorithm to automatically detect ground deformation signals as well as changes in coherence and amplitude in the time series. This toolbox could be a powerful fast-response system for helping volcanological observatories to manage new or ongoing volcanic crisis. Important information regarding the spatial and the temporal evolution of each ground deformation signal will also be added to the COMET database. This will benefit to better understand the conditions in which volcanic unrest leads to an eruption. Such worldwide survey enables us to establish a large catalogue of InSAR products, which will also be suitable for further studies (mapping of new lava flows, modelling of magmatic sources, evaluation of stress interactions).

Shape study of the N =Z nucleus 72Kr via β decay

NASA Astrophysics Data System (ADS)

Briz, J. A.; Nácher, E.; Borge, M. J. G.; Algora, A.; Rubio, B.; Dessagne, Ph.; Maira, A.; Cano-Ott, D.; Courtin, S.; Escrig, D.; Fraile, L. M.; Gelletly, W.; Jungclaus, A.; Le Scornet, G.; Maréchal, F.; Miehé, Ch.; Poirier, E.; Poves, A.; Sarriguren, P.; Taín, J. L.; Tengblad, O.

2015-11-01

The β decay of the N =Z nucleus 72Kr has been studied with the total absorption spectroscopy technique at ISOLDE (CERN). A total B (GT) =0.79 (4 ) gA2/4 π has been found up to an excitation energy of 2.7 MeV. The B (GT) distribution obtained is compared with predictions from state-of-the-art theoretical calculations to learn about the ground state deformation of 72Kr. Although a dominant oblate deformation is suggested by direct comparison with quasiparticle random phase approximation (QRPA) calculations, beyond-mean-field and shell-model calculations favor a large oblate-prolate mixing in the ground state.

Locally distributed crustal deformation in potential areas of phreatic eruptions, detected by InSAR analyses

NASA Astrophysics Data System (ADS)

Kobayashi, Tomokazu

2017-04-01

Phreatic eruptions may be related to transient pressure changes in subsurface regions of hydrothermal systems attributing a heating of shallow aquifers from magma. It means that crustal deformation presumably proceeds with the pressure increase under the ground, which can be a kind of precursor if it would be detected. One of the most difficult points is that as the eruption size becomes smaller, the precursor signal should be more local, suggesting that it is rather hard to identify the anomaly using conventional ground-based observation tools. To mitigate disaster on phreatic eruptions, an effective proactive monitoring method is desired. One of the tools to overcome the drawbacks is SAR observation. I here report several observation results in which locally distributed crustal deformation has been detected in geothermal areas where phreatic eruptions has occurred recently or historically. One of the most important studies is the case of Mt. Hakone where the crustal deformation has been successfully detected two months before small phreatic eruptions. Mt. Hakone holds an active geothermal area, called Owaku-dani, with active fumaroles although no eruption has been known since 12-13 centuries. However, the anomalous activity such as an increase of seismicity started in the end of April, 2015. With this anomalous activity, SAR (ALOS-2) observations have been conducted, and small but significant crustal deformation has been detected in a local area with a diameter of 200 m with a displacement of 5 cm. The amount of deformation has increased with time although the spatial size has not changed, and resultantly the amount reached up to 60 cm. Finally, in the end of June, eruptions occurred just at the local crustal deformation area. It should be noted that the eruption started from the InSAR-detected inflational area. This is an excellent case that we were able to identify the location of small phreatic eruption in advance by detecting anomalous ground inflation. It is also noted that the detection of the precursory signal has contributed to the administrative decision making such as setting up no-go area. In this presentation, in addition to this case, I will show some local ground inflational signals observed in geothermal areas where eruptions have not occurred as yet. Acknowledgements: ALOS-2 data were provided under a cooperative contract with JAXA (Japan Aerospace Exploration Agency). The ownership of ALOS-2 data belongs to JAXA. This study was supported by JSPS KAKENHI Grant Numbers JP16K17797 and JP25350494.

Crustal deformation at very long baseline interferometry sites due to seasonal air-mass and ground water variations

NASA Technical Reports Server (NTRS)

Stolz, A.; Larden, D. R.

1980-01-01

The seasonal deformation normal to the Earth's surface was calculated at stations involved or interested in very long baseline interferometry (VLBI) geodesy and at hypothetical sites in Australia and Brazil using global atmospheric pressure data, values for groundwater storage, and load Love numbers deduced from current Earth models. It was found that the annual range of deformation approached the centimeter level measuring potential of the VLBI technqiue at Greenbank, Haystack, and the Brazil site.

Deformation monitoring at Mount St. Helens in 1981 and 1982

USGS Publications Warehouse

Chadwick, W.W.; Swanson, D.A.; Iwatsubo, E.Y.; Heliker, C.C.; Leighley, T.A.

1983-01-01

For several weeks before each eruption of Mount St. Helens in 1981 and 1982, viscous magma rising in the feeder conduit inflated the lava dome and shoved the crater floor laterally against the immobile crater walls, producing ground cracks and thrust faults. The rates of deformation accelerated before eruptions, and thus it was possible to predict eruptions 3 to 19 days in advance. Lack of deformation outside the crater showed that intrusion of magma during 1981 and 1982 was not voluminous.

Pocket formula for nuclear deformations of actinides

NASA Astrophysics Data System (ADS)

Manjunatha, H. C.; Sridhar, K. N.

2018-06-01

We have formulated a pocket formula for quadrupole (β2), octupole (β3), hexadecapole (β4) and hexacontatetrapole (β6) deformation of the nuclear ground state of all isotopes of actinide nuclei (89 < Z < 103). This formula is first of its kind and produces a nuclear deformation of all isotopes actinide nuclei 89 < Z < 103 with simple inputs of Z and A. Hence, this formula is useful in the fields of nuclear physics to study the structure and interaction of nuclei.

Deformed Shape Calculation of a Full-Scale Wing Using Fiber Optic Strain Data from a Ground Loads Test

NASA Technical Reports Server (NTRS)

Jutte, Christine V.; Ko, William L.; Stephens, Craig A.; Bakalyar, John A.; Richards, W. Lance

2011-01-01

A ground loads test of a full-scale wing (175-ft span) was conducted using a fiber optic strain-sensing system to obtain distributed surface strain data. These data were input into previously developed deformed shape equations to calculate the wing s bending and twist deformation. A photogrammetry system measured actual shape deformation. The wing deflections reached 100 percent of the positive design limit load (equivalent to 3 g) and 97 percent of the negative design limit load (equivalent to -1 g). The calculated wing bending results were in excellent agreement with the actual bending; tip deflections were within +/- 2.7 in. (out of 155-in. max deflection) for 91 percent of the load steps. Experimental testing revealed valuable opportunities for improving the deformed shape equations robustness to real world (not perfect) strain data, which previous analytical testing did not detect. These improvements, which include filtering methods developed in this work, minimize errors due to numerical anomalies discovered in the remaining 9 percent of the load steps. As a result, all load steps attained +/- 2.7 in. accuracy. Wing twist results were very sensitive to errors in bending and require further development. A sensitivity analysis and recommendations for fiber implementation practices, along with, effective filtering methods are included

Visualisation and analysis of shear-deformation bands in unconsolidated Pleistocene sand using ground-penetrating radar: Implications for paleoseismological studies

NASA Astrophysics Data System (ADS)

Brandes, Christian; Igel, Jan; Loewer, Markus; Tanner, David C.; Lang, Jörg; Müller, Katharina; Winsemann, Jutta

2018-05-01

Deformation bands in unconsolidated sediments are of great value for paleoseismological studies in sedimentary archives. Using ground-penetrating radar (GPR), we investigated an array of shear-deformation bands that developed in unconsolidated Pleistocene glacifluvial Gilbert-type delta sediments. A dense grid (spacing 0.6 m) of GPR profiles was measured on top of a 20 m-long outcrop that exposes shear-deformation bands. Features in the radargrams could be directly tied to the exposure. The shear-deformation bands are partly represented by inclined reflectors and partly by the offset of reflections at delta clinoforms. 3-D interpretation of the 2-D radar sections shows that the bands have near-planar geometries that can be traced throughout the entire sediment volume. Thin sections of sediment samples show that the analysed shear-deformation bands have a denser grain packing than the host sediment. Thus they have a lower porosity and smaller pore sizes and therefore, in the vadose zone, the deformation bands have a higher water content due to enhanced capillary forces. This, together with the partially-developed weak calcite cementation and the distinct offset along the bands, are likely the main reasons for the clear and unambiguous expression of the shear-deformation bands in the radar survey. The study shows that deformation-band arrays can clearly be detected using GPR and quickly mapped over larger sediment volumes. With the 3-D analysis, it is further possible to derive the orientation and geometry of the bands. This allows correlation of the bands with the regional fault trend. Studying deformation bands in unconsolidated sediments with GPR is therefore a powerful approach in paleoseismological studies. Based on our data, we postulate that the outcrop is part of a dextral strike-slip zone that was reactivated by glacial isostatic adjustment.

Development of a Standardized Methodology for the Use of COSI-Corr Sub-Pixel Image Correlation to Determine Surface Deformation Patterns in Large Magnitude Earthquakes.

NASA Astrophysics Data System (ADS)

Milliner, C. W. D.; Dolan, J. F.; Hollingsworth, J.; Leprince, S.; Ayoub, F.

2014-12-01

Coseismic surface deformation is typically measured in the field by geologists and with a range of geophysical methods such as InSAR, LiDAR and GPS. Current methods, however, either fail to capture the near-field coseismic surface deformation pattern where vital information is needed, or lack pre-event data. We develop a standardized and reproducible methodology to fully constrain the surface, near-field, coseismic deformation pattern in high resolution using aerial photography. We apply our methodology using the program COSI-corr to successfully cross-correlate pairs of aerial, optical imagery before and after the 1992, Mw 7.3 Landers and 1999, Mw 7.1 Hector Mine earthquakes. This technique allows measurement of the coseismic slip distribution and magnitude and width of off-fault deformation with sub-pixel precision. This technique can be applied in a cost effective manner for recent and historic earthquakes using archive aerial imagery. We also use synthetic tests to constrain and correct for the bias imposed on the result due to use of a sliding window during correlation. Correcting for artificial smearing of the tectonic signal allows us to robustly measure the fault zone width along a surface rupture. Furthermore, the synthetic tests have constrained for the first time the measurement precision and accuracy of estimated fault displacements and fault-zone width. Our methodology provides the unique ability to robustly understand the kinematics of surface faulting while at the same time accounting for both off-fault deformation and measurement biases that typically complicates such data. For both earthquakes we find that our displacement measurements derived from cross-correlation are systematically larger than the field displacement measurements, indicating the presence of off-fault deformation. We show that the Landers and Hector Mine earthquake accommodated 46% and 38% of displacement away from the main primary rupture as off-fault deformation, over a mean deformation width of 183 m and 133 m, respectively. We envisage that correlation results derived from our methodology will provide vital data for near-field deformation patterns and will be of significant use for constraining inversion solutions for fault slip at depth.

Rietveld analysis of X-ray powder diffraction patterns as a potential tool for the identification of impact-deformed carbonate rocks

NASA Astrophysics Data System (ADS)

Huson, S. A.; Foit, F. F.; Watkinson, A. J.; Pope, M. C.

2009-12-01

Previous X-ray powder diffraction (XRD) studies revealed that shock deformed carbonates and quartz have broader XRD patterns than those of unshocked samples. Entire XRD patterns, single peak profiles and Rietveld refined parameters of carbonate samples from the Sierra Madera impact crater, west Texas, unshocked equivalent samples from 95 miles north of the crater and the Mission Canyon Formation of southwest Montana and western Wyoming were used to evaluate the use of X-ray powder diffraction as a potential tool for distinguishing impact deformed rocks from unshocked and tectonically deformed rocks. At Sierra Madera dolostone and limestone samples were collected from the crater rim (lower shock intensity) and the central uplift (higher shock intensity). Unshocked equivalent dolostone samples were collected from well cores drilled outside of the impact crater. Carbonate rocks of the Mission Canyon Formation were sampled along a transect across the tectonic front of the Sevier and Laramide orogenic belts. Whereas calcite subjected to significant shock intensities at the Sierra Madera impact crater can be differentiated from tectonically deformed calcite from the Mission Canyon Formation using Rietveld refined peak profiles, weakly shocked calcite from the crater rim appears to be indistinguishable from the tectonically deformed calcite. In contrast, Rietveld analysis readily distinguishes shocked Sierra Madera dolomite from unshocked equivalent dolostone samples from outside the crater and tectonically deformed Mission Canyon Formation dolomite.

A mechanical model for deformable and mesh pattern wheel of lunar roving vehicle

NASA Astrophysics Data System (ADS)

Liang, Zhongchao; Wang, Yongfu; Chen, Gang (Sheng); Gao, Haibo

2015-12-01

As an indispensable tool for astronauts on lunar surface, the lunar roving vehicle (LRV) is of great significance for manned lunar exploration. An LRV moves on loose and soft lunar soil, so the mechanical property of its wheels directly affects the mobility performance. The wheels used for LRV have deformable and mesh pattern, therefore, the existing mechanical theory of vehicle wheel cannot be used directly for analyzing the property of LRV wheels. In this paper, a new mechanical model for LRV wheel is proposed. At first, a mechanical model for a rigid normal wheel is presented, which involves in multiple conventional parameters such as vertical load, tangential traction force, lateral force, and slip ratio. Secondly, six equivalent coefficients are introduced to amend the rigid normal wheel model to fit for the wheels with deformable and mesh-pattern in LRV application. Thirdly, the values of the six equivalent coefficients are identified by using experimental data obtained in an LRV's single wheel testing. Finally, the identified mechanical model for LRV's wheel with deformable and mesh pattern are further verified and validated by using additional experimental results.

Pathways of volatile migration in the crust beneath Harrat Lunayyir (Saudi Arabia) during the unrest in 2009 revealed by attenuation tomography

NASA Astrophysics Data System (ADS)

Sychev, Ilya; Koulakov, Ivan; El Khrepy, Sami; Al-Arifi, Nassir

2017-01-01

Harrat Lunayyir is a relatively young basaltic field in Saudi Arabia located at the western margin of the Arabian Peninsula. In April-June 2009, strong seismic activity and ground deformations at this site marked the activation of the magma system beneath Harrat Lunayyir. In this study, we present new three-dimensional models of the attenuation of P and S waves during the unrest in 2009 based on the analysis of t*. We measured 1658 and 3170 values of t* for P and S waves, respectively, for the same earthquakes that were previously used for travel time tomography. The resulting anomalies of the P and S wave attenuation look very similar. In the center of the study area, we observe a prominent high-attenuation pattern, which coincides with the most active seismicity at shallow depths and maximum ground deformations. This high-attenuation zone may represent a zone of accumulation and ascending of gases, which originated at depths of 5-7 km due to the decompression of ascending liquid volatiles. Based on these findings and previous tomography studies, we propose that the unrest at Harrat Lunayyir in 2009 was triggered by a sudden injection of unstable liquid volatiles from deeper magma sources. At some depths, they were transformed to gases, which caused the volume to increase, and this led to seismic activation in the areas of phase transformations. The overpressurized gases ultimately found the weakest point in the rigid basaltic cover at the junction of several tectonic faults and escaped to the surface.

Pathways of volatile migration in the crust beneath Harrat Lunayyir (Saudi Arabia) during the unrest in 2009 revealed by attenuation tomography

NASA Astrophysics Data System (ADS)

El Khrepy, Sami; Koulakov, Ivan; Al-Arifi, Nassir; Sychev, Ilya

2017-04-01

Harrat Lunayyir is a relatively young basaltic field in Saudi Arabia located at the western margin of the Arabian Peninsula. In April-June 2009, strong seismic activity and ground deformations at this site marked the activation of the magma system beneath Harrat Lunayyir. In this study, we present new three-dimensional models of the attenuation of P and S waves during the unrest in 2009 based on the analysis of t*. We measured 1658 and 3170 values of t* for P and S waves, respectively, for the same earthquakes that were previously used for travel time tomography. The resulting anomalies of the P and S wave attenuation look very similar. In the center of the study area, we observe a prominent high-attenuation pattern, which coincides with the most active seismicity at shallow depths and maximum ground deformations. This high-attenuation zone may represent a zone of accumulation and ascending of gases, which originated at depths of 5-7 km due to the decompression of ascending liquid volatiles. Based on these findings and previous tomography studies, we propose that the unrest at Harrat Lunayyir in 2009 was triggered by a sudden injection of unstable liquid volatiles from deeper magma sources. At some depths, they were transformed to gases, which caused the volume to increase, and this led to seismic activation in the areas of phase transformations. The overpressurized gases ultimately found the weakest point in the rigid basaltic cover at the junction of several tectonic faults and escaped to the surface.

Application of Vision Metrology to In-Orbit Measurement of Large Reflector Onboard Communication Satellite for Next Generation Mobile Satellite Communication

NASA Astrophysics Data System (ADS)

Akioka, M.; Orikasa, T.; Satoh, M.; Miura, A.; Tsuji, H.; Toyoshima, M.; Fujino, Y.

2016-06-01

Satellite for next generation mobile satellite communication service with small personal terminal requires onboard antenna with very large aperture reflector larger than twenty meters diameter because small personal terminal with lower power consumption in ground base requires the large onboard reflector with high antenna gain. But, large deployable antenna will deform in orbit because the antenna is not a solid dish but the flexible structure with fine cable and mesh supported by truss. Deformation of reflector shape deteriorate the antenna performance and quality and stability of communication service. However, in case of digital beam forming antenna with phased array can modify the antenna beam performance due to adjustment of excitation amplitude and excitation phase. If we can measure the reflector shape precisely in orbit, beam pattern and antenna performance can be compensated with the updated excitation amplitude and excitation phase parameters optimized for the reflector shape measured every moment. Softbank Corporation and National Institute of Information and Communications Technology has started the project "R&D on dynamic beam control technique for next generation mobile communication satellite" as a contracted research project sponsored by Ministry of Internal Affairs and Communication of Japan. In this topic, one of the problem in vision metrology application is a strong constraints on geometry for camera arrangement on satellite bus with very limited space. On satellite in orbit, we cannot take many images from many different directions as ordinary vision metrology measurement and the available area for camera positioning is quite limited. Feasibility of vision metrology application and general methodology to apply to future mobile satellite communication satellite is to be found. Our approach is as follows: 1) Development of prototyping simulator to evaluate the expected precision for network design in zero order and first order 2) Trial measurement for large structure with similar dimension with large deployable reflector to confirm the validity of the network design and instrumentation. In this report, the overview of this R&D project and the results of feasibility study of network design based on simulations on vision metrology and beam pattern compensation of antenna with very large reflector in orbit is discussed. The feasibility of assumed network design for vision metrology and satisfaction of accuracy requirements are discussed. The feasibility of beam pattern compensation by using accurately measured reflector shape is confirmed with antenna pattern simulation for deformed parabola reflector. If reflector surface of communication satellite can be measured routinely in orbit, the antenna pattern can be compensated and maintain the high performance every moment.

Figure-Ground Segmentation Using Factor Graphs

PubMed Central

Shen, Huiying; Coughlan, James; Ivanchenko, Volodymyr

2009-01-01

Foreground-background segmentation has recently been applied [26,12] to the detection and segmentation of specific objects or structures of interest from the background as an efficient alternative to techniques such as deformable templates [27]. We introduce a graphical model (i.e. Markov random field)-based formulation of structure-specific figure-ground segmentation based on simple geometric features extracted from an image, such as local configurations of linear features, that are characteristic of the desired figure structure. Our formulation is novel in that it is based on factor graphs, which are graphical models that encode interactions among arbitrary numbers of random variables. The ability of factor graphs to express interactions higher than pairwise order (the highest order encountered in most graphical models used in computer vision) is useful for modeling a variety of pattern recognition problems. In particular, we show how this property makes factor graphs a natural framework for performing grouping and segmentation, and demonstrate that the factor graph framework emerges naturally from a simple maximum entropy model of figure-ground segmentation. We cast our approach in a learning framework, in which the contributions of multiple grouping cues are learned from training data, and apply our framework to the problem of finding printed text in natural scenes. Experimental results are described, including a performance analysis that demonstrates the feasibility of the approach. PMID:20160994

Octupole deformation in neutron-rich actinides and superheavy nuclei and the role of nodal structure of single-particle wavefunctions in extremely deformed structures of light nuclei

NASA Astrophysics Data System (ADS)

Afanasjev, A. V.; Abusara, H.; Agbemava, S. E.

2018-03-01

Octupole deformed shapes in neutron-rich actinides and superheavy nuclei as well as extremely deformed shapes of the N∼ Z light nuclei have been investigated within the framework of covariant density functional theory. We confirmed the presence of new region of octupole deformation in neutron-rich actinides with the center around Z∼ 96,N∼ 196 but our calculations do not predict octupole deformation in the ground states of superheavy Z≥slant 108 nuclei. As exemplified by the study of 36Ar, the nodal structure of the wavefunction of occupied single-particle orbitals in extremely deformed structures allows to understand the formation of the α-clusters in very light nuclei, the suppression of the α-clusterization with the increase of mass number, the formation of ellipsoidal mean-field type structures and nuclear molecules.

Ground movement at Somma-Vesuvius from Last Glacial Maximum

NASA Astrophysics Data System (ADS)

Marturano, Aldo; Aiello, Giuseppe; Barra, Diana; Fedele, Lorenzo; Morra, Vincenzo

2012-01-01

Detailed micropalaeontological and petrochemical analyses of rock samples from two boreholes drilled at the archaeological excavations of Herculaneum, ~ 7 km west of the Somma -Vesuvius crater, allowed reconstruction of the Late Quaternary palaeoenvironmental evolution of the site. The data provide clear evidence for ground uplift movements involving the studied area. The Holocenic sedimentary sequence on which the archaeological remains of Herculaneum rest has risen several meters at an average rate of ~ 4 mm/yr. The uplift has involved the western apron of the volcano and the Sebeto-Volla Plain, a populous area including the eastern suburbs of Naples. This is consistent with earlier evidence for similar uplift for the areas of Pompeii and Sarno valley (SE of the volcano) and the Somma -Vesuvius eastern apron. An axisimmetric deep source of strain is considered responsible for the long-term uplift affecting the whole Somma -Vesuvius edifice. The deformation pattern can be modeled as a single pressure source, sited in the lower crust and surrounded by a shell of Maxwell viscoelastic medium, which experienced a pressure pulse that began at the Last Glacial Maximum.

Orbital shape in intentional skull deformations and adult sagittal craniosynostoses.

PubMed

Sandy, Ronak; Hennocq, Quentin; Nysjö, Johan; Giran, Guillaume; Friess, Martin; Khonsari, Roman Hossein

2018-06-21

Intentional cranial deformations are the result of external mechanical forces exerted on the skull vault that modify the morphology of various craniofacial structures such as the skull base, the orbits and the zygoma. In this controlled study, we investigated the 3D shape of the orbital inner mould and the orbital volume in various types of intentional deformations and in adult non-operated scaphocephaly - the most common type of craniosynostosis - using dedicated morphometric methods. CT scans were performed on 32 adult skulls with intentional deformations, 21 adult skull with scaphocephaly and 17 non-deformed adult skulls from the collections of the Muséum national d'Histoire naturelle in Paris, France. The intentional deformations group included six skulls with Toulouse deformations, eight skulls with circumferential deformations and 18 skulls with antero-posterior deformations. Mean shape models were generated based on a semi-automatic segmentation technique. Orbits were then aligned and compared qualitatively and quantitatively using colour-coded distance maps and by computing the mean absolute distance, the Hausdorff distance, and the Dice similarity coefficient. Orbital symmetry was assessed after mirroring, superimposition and Dice similarity coefficient computation. We showed that orbital shapes were significantly and symmetrically modified in intentional deformations and scaphocephaly compared with non-deformed control skulls. Antero-posterior and circumferential deformations demonstrated a similar and severe orbital deformation pattern resulting in significant smaller orbital volumes. Scaphocephaly and Toulouse deformations had similar deformation patterns but had no effect on orbital volumes. This study showed that intentional deformations and scaphocephaly significantly interact with orbital growth. Our approach was nevertheless not sufficient to identify specific modifications caused by the different types of skull deformations or by scaphocephaly. © 2018 Anatomical Society.

Hazard-to-Risk: High-Performance Computing Simulations of Large Earthquake Ground Motions and Building Damage in the Near-Fault Region

NASA Astrophysics Data System (ADS)

Miah, M.; Rodgers, A. J.; McCallen, D.; Petersson, N. A.; Pitarka, A.

2017-12-01

We are running high-performance computing (HPC) simulations of ground motions for large (magnitude, M=6.5-7.0) earthquakes in the near-fault region (< 50 km) to 5 Hz and higher. Ground motions are then used as forcing functions for canonical steel moment frame buildings throughout the near-fault domain. For ground motions, we are using SW4, a fourth order summation-by-parts finite difference time-domain code running on 10,000-100,000's of cores. Earthquake ruptures are generated using the Graves and Pitarka (2017) method. We validated ground motion intensity measurements against Ground Motion Prediction Equations. We considered two events (M=6.5 and 7.0) for vertical strike-slip ruptures with three-dimensional (3D) basin structures, including stochastic heterogeneity. We have also considered M7.0 scenarios for a Hayward Fault rupture scenario which effects the San Francisco Bay Area and northern California using both 1D and 3D earth structure. Dynamic, inelastic response of canonical buildings is computed with the NEVADA, a nonlinear, finite-deformation finite element code. Canonical buildings include 3-, 9-, 20- and 40-story steel moment frame buildings. Damage potential is tracked by the peak inter-story drift (PID) ratio, which measures the maximum displacement between adjacent floors of the building and is strongly correlated with damage. PID ratios greater 1.0 generally indicate non-linear response and permanent deformation of the structure. We also track roof displacement to identify permanent deformation. PID (damage) for a given earthquake scenario (M, slip distribution, hypocenter) is spatially mapped throughout the SW4 domain with 1-2 km resolution. Results show that in the near fault region building damage is correlated with peak ground velocity (PGV), while farther away (> 20 km) it is better correlated with peak ground acceleration (PGA). We also show how simulated ground motions have peaks in the response spectra that shift to longer periods for larger magnitude events and for locations of forward directivity, as has been reported by Sommerville (2003). These advanced numerical simulation capabilities provide a detailed look at the regional distribution of ground motions and allow us to quantify how ground motion hazard translate to risk for specific structures on a regional scale.

Monitoring The Stability Of Levees With Time-Series ENVISAT ASAR Images

NASA Astrophysics Data System (ADS)

Pei, Yuanyuan; Liao, Mingsheng; Wang, Teng; Zhang, Lu

2012-01-01

Levees are constructed to protect coastal cities from typhoon, flood, and sea tide. Since the stability of levees is important, it is necessary to monitor their deformation regularly. Repeat-track space-borne SAR images are useful for environment monitoring, especially for ground deformation monitoring. Shanghai resides on the Yangtze River Delta on China’s eastern coast. Each year, the city is hit by typhoons from the Pacific Ocean and threatened by the flood of the Yangtze River. We used Persistent Scatterer Interferometry to monitor the deformation of the levees. Our experiments show that the levees around Pudong airport and Lingang town suffer from serious deformation.

Integration of Space-borne SAR and Ground-Based Radar for 3D Deformation Mapping of the Central Calaveras Fault at Coyote Dam

NASA Astrophysics Data System (ADS)

Werner, C. L.; Baker, B.; Milillo, P.; Magnard, C.; Strozzi, T.; Wegmüller, U.

2017-12-01

The Central Calaveras Fault (CCF) passes directly through Coyote Dam located southeast of Morgan Hill, California. This earthen embankment dam owned and operated by the Santa Clara Valley Water District (District), has experienced over 80 cm of accumulated fault creep since its construction in 1936. The average slip rate is 10 to 15 mm/year as measured using surveying, GPS, and more recently, terrestrial radar interferometry (TRI). The CCF is a right-lateral strike-slip fault that has the potential for a M7.25 earthquake resulting in meter scale displacement. In 2015, the District initiated a geological analysis of the CCF integrating past surveying, GPS data, TRI deformation mapping, paleoseismic trenching, and boreholes. The initial TRI survey included dam measurements from two locations, imaging the upstream and downstream embankments over the period from February to July 2015. The TRI data from the downstream embankment data showed a complex deformation pattern not consistent with a strike-slip fault model. A second measurement campaign was initiated utilizing multiple radar viewpoints with the aim of resolving the 3D deformation field of the downstream embankment. The campaign occurred between May and November 2016 and showed an unexpected strong westward and downward movement exceeding 2 cm/year (see Figure). TRI data were acquired from 4 separate observation points every 2 to 4 weeks during this campaign. Point target analysis methods were used to avoid contamination of the deformation data by vegetation and radar shadow. Deformation uncertainty in the downstream fault zone was relatively high due to the nearly coplanar arrangement of the TRI observation points. To better constrain the vertical deformation, in this report we integrate spaceborne measurements from the Cosmo-SkyMed (CS) radar satellite in the 3D deformation solution. The LOS to the satellite has a large vertical component not present in the TRI measurement geometry that facilitates the inversion. The CS 3-meter resolution data have been acquired every 16 days between 2011 and 2017. These data are used to test the consistency of the TRI results and the long observation period permits identification of periodic hydrologic signals suggested in the TRI measurements.

Monitoring unrest in a large silicic caldera, the long Valley-inyo craters volcanic complex in east-central California

NASA Astrophysics Data System (ADS)

Hill, D. P.

1984-06-01

Recent patterns of geologic unrest in long Valley caldera in east-central California emphasize that this large, silicic volcanic system and the adjacent, geologically youthful Inyo-Mono Craters volcanic chain are still active and capable of producing locally hazardous volcanic eruptions. A series of four magnitude -6 earthquakes in May 1980 called attention to this current episode of unrest, and subsequent activity has included numerous earthquake swarms in the south moat of the caldera accompanied by inflation of the resurgent dome by more than 50 cm over the last five years. The seismicity associated with this unrest is currently monitored by a network of 31 telemetered seismic stations with an automatic processing system that yelds hypocentral locations and earthquake magnitudes in near-real time. Deformation of the ground is monitored by a) a series of overlapping trilateration networks that provide coverage ranging from annual measurements of regional deformation to daily measurements of deformation local to the active, southern section of the caldera, b) a regional network of level lines surveyed annually, c) a regional network of precise gravity stations occupied annually, d) local, L-shaped level figures surveyed every few months, and e) a network of fourteen borehole tiltmeter clusters (two instruments in each cluster) and a borehole dilatometer, the telemetered signals from which provide continuous data on deformation rates. Additional telemetered data provide continuous information on fluctuations in the local magnetic field, hydrogen gas emission rates at three sites, and water level and temperatures in three wells. Continuous data on disharge rates and temperatures from hot springs and fumaroles are collected by several on-site recorders within the caldera, and samples for liquid and gas chemistry are collected several times per year from selected hot springs and fumaroles.

Catalogs of micro-seismicity recorded at the Pechgraben landslide (Upper Austria)

NASA Astrophysics Data System (ADS)

Provost, Floriane; Hibert, Clément; Vouillamoz, Naomi; Malet, Jean-Philippe; Ottowitz, David; Jochum, Birgit

2017-04-01

The microseismicity activity of soft-rock landslides (i.e. developed in clays and clay-shales) present various types of seismic event associated with the slope deformation. They are assumed to be linked to the slip at the interface with the bedrock or at the boundaries of the landslide, to material failures, to fissure openings or to fluid transfers within the medium. It is currently necessary to document the microseismicity generated by soft-rock landslides on a larger amount of instrumented slopes in order to validate the current seismic typology and understand the source mechanisms in relation with the deformation. Previous studies have shown the interest of the Pechgraben (Upper Austria) clay-shale landslide for such documentation. This landslide was reactivated in summer 2013 after heavy rainfalls and is characterized by a shallow bedrock (<10m) and varying displacement rates in space and time (from mm.day-1 to cm.day-1). A short pilot seismic campaign (<9 days) was carried out in 2015 and micro-earthquakes as well as episodic tremor-like signals were recorded. A new passive seismic campaign was conducted during one month in November-December 2016. Two broadband three-component seismometers were installed facing each other on the two stable borders of the slope with one tripartite seismic array deployed in the center, on top of the most active area of the landslide. The deformation pattern of the slope was monitored remotely with a ground-based InSAR at a high frequency (10 min). This study aims to present the variety of seismic sources generated by the landslide, using supervised machine learning algorithms for event detection and classification, and to correlate the resulting micro-seismic catalog with the changes in time of the slope deformation.

Monitoring the UPS and Downs of Sumatra and Java with D-Insar Time-Series

NASA Astrophysics Data System (ADS)

Chaussard, E.; Amelung, F.

2010-12-01

We performed, for the first time, a global D-InSAR survey of the Indonesian islands of Sumatra and Java to define locations where deformation is occurring. The goals of this study are 1) to create an inventory of actively deforming volcanic centers and 2) monitor all types of ground motion. This work provides ground deformation data for previously unmonitored areas and can assist the Indonesian authorities to improve hazards assessment. The D-InSAR survey covers an area of about 500 000 km2 and 3000 km long on the islands of Sumatra, Java and Bali. We used ALOS data from 45 tracks and more than 1500 granules obtained from the Alaska Satellite Facility (ASF) through the US Government Research Consortium (USGRC). We completed more than 1000 interferograms spanning a period from the end of 2006 to the beginning of 2009. L-band SAR images enable deformation mapping at global scales even in highly vegetated areas where C-band signal experiences loss of coherence. To identify locations where ground deformations are occurring, we used multiple SAR acquisitions of the same area and performed time series analysis using the Small BAseline Subset (SBAS) method. Interferograms with a maximum spatial baseline of 3000 m were phase-unwrapped and subsequently inverted for the phase with respect to the first acquisition. Temporal coherence of each pixel is computed on the set of interferograms in order to select only pixels with high temporal coherence. The compiled InSAR velocity map reveals the background level of activity of the 84 volcanic centers constituting the Sumatra, Java and Bali volcanic arcs. We identified possible uplift at 6 volcanic centers: Agung (Bali), Lamongan (Java), Lawu (Java), Slamet (Java), Kerinci (Sumatra) and Sinabung (Sumatra). Moreover, we identified subsidence in 5 major cities and 1 coastal area. Subsidence rates range from 6 cm/yr in Medan, the largest city of Sumatra, to more than 15 cm/yr in Jakarta. These major subsidence areas are probably due to ground water extraction needed to support the increasing population and industrial activities.

A comparative analysis of numerical approaches to the mechanics of elastic sheets

NASA Astrophysics Data System (ADS)

Taylor, Michael; Davidovitch, Benny; Qiu, Zhanlong; Bertoldi, Katia

2015-06-01

Numerically simulating deformations in thin elastic sheets is a challenging problem in computational mechanics due to destabilizing compressive stresses that result in wrinkling. Determining the location, structure, and evolution of wrinkles in these problems has important implications in design and is an area of increasing interest in the fields of physics and engineering. In this work, several numerical approaches previously proposed to model equilibrium deformations in thin elastic sheets are compared. These include standard finite element-based static post-buckling approaches as well as a recently proposed method based on dynamic relaxation, which are applied to the problem of an annular sheet with opposed tractions where wrinkling is a key feature. Numerical solutions are compared to analytic predictions of the ground state, enabling a quantitative evaluation of the predictive power of the various methods. Results indicate that static finite element approaches produce local minima that are highly sensitive to initial imperfections, relying on a priori knowledge of the equilibrium wrinkling pattern to generate optimal results. In contrast, dynamic relaxation is much less sensitive to initial imperfections and can generate low-energy solutions for a wide variety of loading conditions without requiring knowledge of the equilibrium solution beforehand.

Performance of San Fernando dams during 1994 Northridge earthquake

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bardet, J.P.; Davis, C.A.

1996-07-01

The 1994 Northridge and 1971 San Fernando Earthquakes subjected the Lower and Upper San Fernando Dams of the Van Norman Complex in the San Fernando Valley, Calif., to strong near-source ground motions. In 1994, these earth dams, which were out of service and retained only a few meters of water, extensively cracked and settled due to the liquefaction of their hydraulic fill. The Lower San Fernando Dam moved over 15 cm upstream as the hydraulic fill liquefied beneath its upstream slope. The Upper San Fernando Dam moved even more and deformed in a complicated three-dimensional pattern. The responses of themore » Lower and Upper San Fernando Dams during the 1994 Northridge Earthquake, although less significant than in 1971, provide the geotechnical engineering community with two useful case histories.« less

Finite elements analysis of an underground collector installed by pipe-jacking method

NASA Astrophysics Data System (ADS)

María Díaz-Díaz, Luis; Omer, Joshua; Arias, Daniel; Pando, Luis

2016-04-01

This study presents a useful analysis method for estimating simultaneously the stability, stress distribution and groundwater seepage as micro - tunnel is being advanced into the ground. The research is mainly concerned with the results of a case study conducted on a project to create a long industrial collector of effluent network in the east bank of the river Avilés (north coast of Spain). This coastal city has significant port and industrial installations in its environs. The geology of the location comprises Quaternary deposits on both flanks of the estuary and includes different highly variable geotechnical behavior. The industrial effluent network, constructed in the year 2010, has a length of 13.087 km and consists of 1.5 m diameter pipes, reaching a maximum depth of 5.8 m below the surface. Only the first 7.0 km of the collector (south area) were formed using pipe-jacking method whilst the rest were formed in open excavations or surface laid. Using the commercial software RS2, a 2D finite element program for soil and rock application, the ground response to pipe jacking in pipeline installation in Avilés was analyzed. Both axi-symmetric and plane strain analyses were carried out in RS2 to simulate in 3D the ground response to pipe advancement. The results demonstrate how much of deformation there is at ground surface in the immediate vicinity of the pipeline. The main objective is to show the possible patterns of ground subsidence and tunnel stresses to inform designers as to whether the tunnel will be stable and safe.

Generation of shape complexity through tissue conflict resolution

PubMed Central

Rebocho, Alexandra B; Southam, Paul; Kennaway, J Richard; Coen, Enrico

2017-01-01

Out-of-plane tissue deformations are key morphogenetic events during plant and animal development that generate 3D shapes, such as flowers or limbs. However, the mechanisms by which spatiotemporal patterns of gene expression modify cellular behaviours to generate such deformations remain to be established. We use the Snapdragon flower as a model system to address this problem. Combining cellular analysis with tissue-level modelling, we show that an orthogonal pattern of growth orientations plays a key role in generating out-of-plane deformations. This growth pattern is most likely oriented by a polarity field, highlighted by PIN1 protein localisation, and is modulated by dorsoventral gene activity. The orthogonal growth pattern interacts with other patterns of differential growth to create tissue conflicts that shape the flower. Similar shape changes can be generated by contraction as well as growth, suggesting tissue conflict resolution provides a flexible morphogenetic mechanism for generating shape diversity in plants and animals. DOI: http://dx.doi.org/10.7554/eLife.20156.001 PMID:28166865

Modeling of thermomechanical changes of extreme-ultraviolet mask and their dependence on absorber variation

NASA Astrophysics Data System (ADS)

Ban, Chung-Hyun; Park, Eun-Sang; Park, Jae-Hun; Oh, Hye-Keun

2018-06-01

Thermal and structural deformation of extreme-ultraviolet lithography (EUVL) masks during the exposure process may become important issues as these masks are subject to rigorous image placement and flatness requirements. The reflective masks used for EUVL absorb energy during exposure, and the temperature of the masks rises as a result. This can cause thermomechanical deformation that can reduce the pattern quality. The use of very thick low-thermal-expansion substrate materials (LTEMs) may reduce energy absorption, but they do not completely eliminate mask deformation. Therefore, it is necessary to predict and optimize the effects of energy transferred from the extreme-ultraviolet (EUV) light source and the resultant patterns of structured EUV masks with complex multilayers. Our study shows that heat accumulates in the masks as exposure progresses. It has been found that a higher absorber ratio (pattern density) applied to the patterning of EUV masks exacerbates the problem, especially in masks with more complex patterns.

A Multipixel Time Series Analysis Method Accounting for Ground Motion, Atmospheric Noise, and Orbital Errors

NASA Astrophysics Data System (ADS)

Jolivet, R.; Simons, M.

2018-02-01

Interferometric synthetic aperture radar time series methods aim to reconstruct time-dependent ground displacements over large areas from sets of interferograms in order to detect transient, periodic, or small-amplitude deformation. Because of computational limitations, most existing methods consider each pixel independently, ignoring important spatial covariances between observations. We describe a framework to reconstruct time series of ground deformation while considering all pixels simultaneously, allowing us to account for spatial covariances, imprecise orbits, and residual atmospheric perturbations. We describe spatial covariances by an exponential decay function dependent of pixel-to-pixel distance. We approximate the impact of imprecise orbit information and residual long-wavelength atmosphere as a low-order polynomial function. Tests on synthetic data illustrate the importance of incorporating full covariances between pixels in order to avoid biased parameter reconstruction. An example of application to the northern Chilean subduction zone highlights the potential of this method.

Operational Monitoring of Mines by COSMO-SkyMed PSP SAR Interferometry

NASA Astrophysics Data System (ADS)

Costantini, Mario; Malvarosa, Fabio; Miniati, Federico; de Assis, Luciano Mozer

2016-08-01

Synthetic aperture radar (SAR) interferometry is a powerful technology for detection and monitoring of slow ground surface movements. Monitoring of ground deformations in mining structures is an important application, particularly difficult because the scene changes with time. The persistent scatterer pair (PSP) approach, recently proposed to overcome some limitations of standard persistent scatter interferometry, proved to be effective also for mine monitoring. In this work, after resuming the main ideas of the PSP method, we describe the PSP measurements obtained from high- resolution X-band COSMO-SkyMed data over a large mining area in Minas Gerais state, Brazil. The outcomes demonstrate that dense and accurate ground deformation measurements can be obtained on the mining area and its structures (such as open pits, waste dumps, conveyor belts, water and tailings dams, etc.), achieving a consistent global view including also areas where field instruments are not installed.

Analysis of an Aircraft Honeycomb Sandwich Panel with Circular Face Sheet/Core Disbond Subjected to Ground-Air Pressurization

NASA Technical Reports Server (NTRS)

Rinker, Martin; Krueger, Ronald; Ratcliffe, James

2013-01-01

The ground-air pressurization of lightweight honeycomb sandwich structures caused by alternating pressure differences between the enclosed air within the honeycomb core and the ambient environment is a well-known and controllable loading condition of aerospace structures. However, initial face sheet/core disbonds intensify the face sheet peeling effect of the internal pressure load significantly and can decrease the reliability of the sandwich structure drastically. Within this paper, a numerical parameter study was carried out to investigate the criticality of initial disbonds in honeycomb sandwich structures under ground-air pressurization. A fracture mechanics approach was used to evaluate the loading at the disbond front. In this case, the strain energy release rate was computed via the Virtual Crack Closure Technique. Special attention was paid to the pressure-deformation coupling which can decrease the pressure load within the disbonded sandwich section significantly when the structure is highly deformed.

Seismic anisotropy and large-scale deformation of the Eastern Alps

NASA Astrophysics Data System (ADS)

Bokelmann, Götz; Qorbani, Ehsan; Bianchi, Irene

2013-12-01

Mountain chains at the Earth's surface result from deformation processes within the Earth. Such deformation processes can be observed by seismic anisotropy, via the preferred alignment of elastically anisotropic minerals. The Alps show complex deformation at the Earth's surface. In contrast, we show here that observations of seismic anisotropy suggest a relatively simple pattern of internal deformation. Together with earlier observations from the Western Alps, the SKS shear-wave splitting observations presented here show one of the clearest examples yet of mountain chain-parallel fast orientations worldwide, with a simple pattern nearly parallel to the trend of the mountain chain. In the Eastern Alps, the fast orientations do not connect with neighboring mountain chains, neither the present-day Carpathians, nor the present-day Dinarides. In that region, the lithosphere is thin and the observed anisotropy thus resides within the asthenosphere. The deformation is consistent with the eastward extrusion toward the Pannonian basin that was previously suggested based on seismicity and surface geology.

A Comparative Study of Random Patterns for Digital Image Correlation

NASA Astrophysics Data System (ADS)

Stoilov, G.; Kavardzhikov, V.; Pashkouleva, D.

2012-06-01

Digital Image Correlation (DIC) is a computer based image analysis technique utilizing random patterns, which finds applications in experimental mechanics of solids and structures. In this paper a comparative study of three simulated random patterns is done. One of them is generated according to a new algorithm, introduced by the authors. A criterion for quantitative evaluation of random patterns after the calculation of their autocorrelation functions is introduced. The patterns' deformations are simulated numerically and realized experimentally. The displacements are measured by using the DIC method. Tensile tests are performed after printing the generated random patterns on surfaces of standard iron sheet specimens. It is found that the new designed random pattern keeps relatively good quality until reaching 20% deformation.

Shape equivalence under perspective and projective transformations.

PubMed

Wagemans, J; Lamote, C; Van Gool, L

1997-06-01

When a planar shape is viewed obliquely, it is deformed by a perspective deformation. If the visual system were to pick up geometrical invariants from such projections, these would necessarily be invariant under the wider class of projective transformations. To what extent can the visual system tell the difference between perspective and nonperspective but still projective deformations of shapes? To investigate this, observers were asked to indicate which of two test patterns most resembled a standard pattern. The test patterns were related to the standard pattern by a perspective or projective transformation, or they were completely unrelated. Performance was slightly better in a matching task with perspective and unrelated test patterns (92.6%) than in a projective-random matching task (88.8%). In a direct comparison, participants had a small preference (58.5%) for the perspectively related patterns over the projectively related ones. Preferences were based on the values of the transformation parameters (slant and shear). Hence, perspective and projective transformations yielded perceptual differences, but they were not treated in a categorically different manner by the human visual system.

Slit Effect of Common Ground Patterns in Affecting Cross-Talk Noise between Two Parallel Signal Traces on Printed Circuit Boards

NASA Astrophysics Data System (ADS)

Maeno, Tsuyoshi; Sakurai, Yukihiko; Unou, Takanori; Ichikawa, Kouji; Fujiwara, Osamu

It is well-known that electromagnetic (EM) disturbances in vehicle-mounted radios are mainly caused by conducted noise currents flowing through wiring-harnesses from vehicle-mounted printed circuit boards (PCBs) with common ground patterns with slits. To evaluate the noise current outflows from the PCBs of this kind, we previously measured noise current outflows from four types of simple three-layer PCBs having two perpendicular signal traces and different ground patterns with/without slits, and showed that slits on a ground pattern allow conducted noise currents to flow out from PCBs, while the levels for the symmetric slits ground type are smaller compared to the case for two asymmetric slits ground types. In the present study, to further investigate the above finding, we fabricated six types of simple two-layer PCBs having two parallel signal traces and different ground patterns with/without slits, and measured the cross-talk noise between the traces. As a result, we found that the ground patterns with the slits perpendicular to the traces increase the cross-talk noise levels, which are larger by 19-42 dB than those for the ground pattern with no slits, while the ground patterns with the slits in parallel with the traces can suppress the noise levels, which are slightly smaller by 2.5-4.5 dB compared to the case for the no-slit ground pattern. These results were confirmed by the FDTD simulation, and were also qualitatively explained from an equivalent bridge circuit model we previously proposed.

A 3D imaging system for the non-intrusive in-flight measurement of the deformation of an aircraft propeller and a helicopter rotor

NASA Astrophysics Data System (ADS)

Stasicki, Bolesław; Boden, Fritz; Ludwikowski, Krzysztof

2017-02-01

The non-intrusive in-flight deformation measurement and the resulting local pitch of an aircraft propeller or helicopter rotor blade is a demanding task. The idea of an imaging system integrated and rotating with the air-craft propeller has already been presented at the 30th International Congress on High-Speed Imaging and Photonics (ICHSIP30) in 2012. Since then this system has been designed, constructed and tested in the laboratory as well as in-flight on the Cobra VUT100 of Evektor Aerotechnik, Kunovice (CZ). The major aim of the EU FP7 project AIM2 ("Advanced In-flight Measurement techniques 2" - contract No. 266107) was to ascertain the feasibility of this technique under extreme conditions - vibration and large centrifugal forces - to real flight testing. Based on the gained experience a new rotating system for the application on helicopter rotors has recently been constructed and tested on the whirl tower of Airbus Helicopters, Donauwoerth (D). In this paper the principle of the applied Image Pattern Correlation Technique (IPCT), a specialized type of Digital Image Correlation (DIC), is outlined and the construction of both rotating 3D image acquisition systems dedicated to the in-flight deformation measurement of the aircraft propeller and helicopter rotor are described. Furthermore, the results of the ground and in-flight tests of these systems will be shown and discussed. The obtained results will be helpful for manufacturers in the design of their future aircrafts.

A novel 3D deformation measurement method under optical microscope for micro-scale bulge-test

NASA Astrophysics Data System (ADS)

Wu, Dan; Xie, Huimin

2017-11-01

A micro-scale 3D deformation measurement method combined with optical microscope is proposed in this paper. The method is based on gratings and phase shifting algorithm. By recording the grating images before and after deformation from two symmetrical angles and calculating the phases of the grating patterns, the 3D deformation field of the specimen can be extracted from the phases of the grating patterns. The proposed method was applied to the micro-scale bulge test. A micro-scale thermal/mechanical coupling bulge-test apparatus matched with the super-depth microscope was exploited. With the gratings fabricated onto the film, the deformed morphology of the bulged film was measured reliably. The experimental results show that the proposed method and the exploited bulge-test apparatus can be used to characterize the thermal/mechanical properties of the films at micro-scale successfully.

Persistent Scatterer InSAR monitoring of Bratislava urban area

NASA Astrophysics Data System (ADS)

Bakon, Matus; Perissin, Daniele; Papco, Juraj; Lazecky, Milan

2014-05-01

The main purpose of this research is to monitor the ground stability of Bratislava urban area by application of the satellite radar interferometry. Bratislava, the capital city of Slovakia, is situated in its south-west on the borders with Austria and Hungary and only 62 kilometers from the border with Czech Republic. With an exclusive location and good infrastructure, the city attracts foreign investors and developers, what has resulted in unprecedented boom in construction in recent years. Another thing is that Danube River in the last five hundred years caused a hundred of devastating floods, so therefore flood occurs every five years, on average. From geological point of view, the Little Carpathians covers the main part of study area and are geologically and tectonically interesting. The current state of relief and spatial distribution of individual geological forms is the result of vertical geodynamic movements of tectonic blocks, e.g., subsiding parts of Vienna Basin and Danubian Basin or uplifting mountains. The Little Carpathians horst and the area of Vienna Basin contains a number of tectonic faults, where ground motions as a result of geodynamic processes are mostly expected. It is assumed that all the phenomena stated above has an impact on the spatial composition of the Earth's surface in Bratislava urban area. As nowadays surface of the Little Carpathians is heavily eroded and morphology smoothed, question of this impact cannot be answered only by interpreting geological tectonic maps. Furthermore, expected changes have never been revealed by any geodetic measurements which would offer advantages of satellite radar interferometry concerning temporal coverage, spatial resolution and accuracy. Thus the generation of ground deformation maps using satellite radar interferometry could gather valuable information. The work aims to perform a series of differential interferograms and PSInSAR (Persistent Scatterer Interferometric Synthetic Aperture Radar) technique, covering the target area with 57 Envisat ASAR images from Ascending Track No. 229 (32) and Descending Track No. 265 (25) captured between years 2002 and 2010. Processing involves Sarproz (Copyright (c) 2009 Daniele Perissin) a powerful software solution for obtaining differential interferograms and performing PSInSAR methodology. The area of interest to investigate the deformation phenomena is covering approximately 16 by 16 kilometers (256 sqkm). For evaluation of PSInSAR potential to detect and monitor ground displacements, PS derived time series of deformation signal were compared to the field GNSS data from three GNSS stations coded PIL1, BRAT and GKU4. By the detailed look on the deformation maps the investigated urban area of Bratislava is relatively stable with the deformation rates within the few (±5) millimeters. The comparison of PSInSAR derived time series with GNSS data indicates good correlation and confirms achievable precision and applicability of InSAR measurements for ground stability monitoring purposes. Data for this work were provided by European Space Agency within the Category-1 project ID 9981: "Detection of ground deformation using radar interferometry techniques". The authors are grateful to the Tatrabanka Foundation and The National Scholarship Programme of the Slovak Republic for the opportunity to work together. Data have been processed by the Sarproz (Copyright (c) 2009 Daniele Perissin) and visualised in Google Earth. This paper is also the result of the implementation of the project: the National Centre of Earth's Surface Deformation Diagnostic in the area of Slovakia, ITMS 26220220108 supported by the Research and Development Operational Programme funded by the ERDF and the grant No. 1/0642/13 of the Slovak Grant Agency VEGA.

Results from a model-independent method of monitoring a geodetic network for patterns of transient deformation

NASA Technical Reports Server (NTRS)

Hurst, Kenneth; Granat, Robert

2005-01-01

We have implmented two multi-station detectors for transient crustal deformation within the Southern California Integrated GPS (SCGIN). One the the primary goals of SCIGN is to detect transient deformation associated with the earthquake cycle in Southern California.

Wavefront correction performed by a deformable mirror of arbitrary actuator pattern within a multireflection waveguide.

PubMed

Ma, Xingkun; Huang, Lei; Bian, Qi; Gong, Mali

2014-09-10

The wavefront correction ability of a deformable mirror with a multireflection waveguide was investigated and compared via simulations. By dividing a conventional actuator array into a multireflection waveguide that consisted of single-actuator units, an arbitrary actuator pattern could be achieved. A stochastic parallel perturbation algorithm was proposed to find the optimal actuator pattern for a particular aberration. Compared with conventional an actuator array, the multireflection waveguide showed significant advantages in correction of higher order aberrations.

Geodetic monitoring of tectonic deformation: Toward a strategy

NASA Technical Reports Server (NTRS)

1981-01-01

Issues of interest and importance to society and science are presented. The problems considered are of national concern; their solutions may contribute to a better understanding of tectonic deformation and earthquake hazards. The need for additional field data, the role of geodetic measurements, the importance of both ground and space techniques, and the need for advanced instrumentation development are discussed.

Examination of global correlations in ground deformation for terrestrial reference frame estimation

NASA Astrophysics Data System (ADS)

Chin, T. M.; Abbondanza, C.; Argus, D. F.; Gross, R. S.; Heflin, M. B.; Parker, J. W.; Wu, X.

2016-12-01

The KALman filter for REFerence frames (KALREF, Wu et al. 2015) has been developed to produce terrestrial reference frame (TRF) solutions. TRFs consist of precise position coordinates and velocity vectors of terrestrial reference sites (with the geocenter as the origin) along with the Earth orientation parameters, and they are produced by combining decades worth of space geodetic data using site tie data. To perform the combination, KALREF relies on stochastic models of the geophysical processes that are causing the Earth's surface to deform and reference sites to be displaced. We are investigating application of the GRACE data to improve the KALREF stochastic models by determining spatial statistics of the deformation of the Earth's surface caused by mass loading. A potential target of improvement is the non-uniform distribution of the geodetic observation sites, which can introduce bias in TRF estimates of the geocenter. The global and relatively uniform coverage of the GRACE measurements is expected to be free of such bias and allow us to improve physical realism of the stochastic model. For such a goal, we examine the spatial correlations in ground deformation derived from several GRACE data sets.[Wu et al. 2015: Journal of Geophysical Research (Solid Earth) 120:3775-3802

An improved data integration algorithm to constrain the 3D displacement field induced by fast deformation phenomena tested on the Napa Valley earthquake

NASA Astrophysics Data System (ADS)

Polcari, Marco; Fernández, José; Albano, Matteo; Bignami, Christian; Palano, Mimmo; Stramondo, Salvatore

2017-12-01

In this work, we propose an improved algorithm to constrain the 3D ground displacement field induced by fast surface deformations due to earthquakes or landslides. Based on the integration of different data, we estimate the three displacement components by solving a function minimization problem from the Bayes theory. We exploit the outcomes from SAR Interferometry (InSAR), Global Positioning System (GNSS) and Multiple Aperture Interferometry (MAI) to retrieve the 3D surface displacement field. Any other source of information can be added to the processing chain in a simple way, being the algorithm computationally efficient. Furthermore, we use the intensity Pixel Offset Tracking (POT) to locate the discontinuity produced on the surface by a sudden deformation phenomenon and then improve the GNSS data interpolation. This approach allows to be independent from other information such as in-situ investigations, tectonic studies or knowledge of the data covariance matrix. We applied such a method to investigate the ground deformation field related to the 2014 Mw 6.0 Napa Valley earthquake, occurred few kilometers from the San Andreas fault system.

ANALYSIS ON THE GROUND DESTROYED FEATURES AND TECTONIC STRESS FIELD OF THE 2008 WENCHUAN EARTHQUAKE AND OUR TREATING TACTICS

NASA Astrophysics Data System (ADS)

Guo, Y.; Wang, H.; Deng, Z.; You, H.

2009-12-01

To research the ground destroyed features and tectonic stress field of the 2008 Wenchuan Earthquake, we went the earthquake-hazard area, Hongkou Town in Dujiangyan City, Yingxiu Town in Wenchuan County, Bailu Town in Pengzhou City, Yinghua Town in Shifang City, Hanwang Town in Mianzhu City and Beichuan Cit early and late twice in 2008. The geological survey was made. Firstly, the ground destroyed features of the Wenchuan Earthquake around both Yingxiu - Beichuan Fracture and Guanxian - Jiangyou Fracture were analyzed. They mainly display as the ground crack ground, road steep slope, ground deformation, road rise high and deformation, road staggering and rupture, etc. Besides, the Wenchuan Earthquake resulted in the great deal of building collapse and lots of bridges damage even break down; It can be seen that the first floor of the building disappeared or damaged seriously; Some building still stood there although damaged by the earthquake; A few of building was damaged slightly and kept intact structure. Furthermore, the earthquake caused earth slide, mudflow and rolling stone, which lead to the building destroyed seriously, river blocked up, the life line engineering destroyed. Secondly, the phenomena of the ground destroy were analyzed preliminarily. The seismic intensity was determined based on the field investigation. The damaged situation of the construction was concluded. Based on the principle of structure geology and making use of the Stereographic projection, the stress field was analyzed according to the attitude, structural nature and relations among the fracture, fault scratch and joint fissure as well as the characteristics of ground deformation thirdly. The geodynamics of the 2008 Wenchuan Earthquake are probed into preliminarily. The main compressive stress (the maximum main stress) σ1 took Northeast by east direction, and the main tensile stress (the minimum main stress)σ3 took Northwest by north direction. The main fracture shows as the right-lateral thrust fracture. The general horizontal diminution and the vertical upheaval of the ground are discussed. At last, the paper compared the relationship between the ground damage and the fracture in the area hit by the 2008 Wenchuan Earthquake. The method to avoid and mitigate the loss of treasure and life caused by the earthquake is proposed. The chief aspects that require the more attention for the reconstruction after disaster are given.

Surface deformation of Ayaz-Akhtarma Mud volcano in Azerbaijan detected by ALOS/ALOS-2 InSAR and its source modeling

NASA Astrophysics Data System (ADS)

Iio, K.; Furuya, M.

2017-12-01

Interferometric synthetic aperture radar (InSAR) allows us to image a wide area with dense spatial resolution without a need for ground-based measurement tools with a precision on the order of a few centimeters. This technique has been mainly used to investigate such ground deformation associated with earthquakes, volcanic eruptions and ground subsidence due to water pumping. However there have been few cases that applied the technique to the activity of mud volcanos. Azerbaijan, located on the western edge of the Caspian Sea in Central Asia, is one of the most abundant countries in term of the population of mud volcanoes over the land. We focused on an especially large and unique mud volcano known as the Ayaz-Akhtarma because the deformation signals are the most evident and peculiar. Antonielli et al., (2014) detected the ground deformation of this mud volcano, using ENVISAT/ASAR C-band SAR data spanning from 2003 to 2005 only along descending path. While the ground displacement at the volcano was 20 cm in line of sight (LOS) for the two years, Antonielli et al., (2014) attributed the observed LOS changes to the uplift and subsidence in the eastern half and western half, respectively, whereas no source model was presented in the study. In the previous study, however, the 3D displacements were totally uncertain because of the restricted looking geometry. We could observe the displacements, based not only on the ALOS data along the ascending path that is the opposite look direction from the previous study but also on the ALOS-2 data for ascending and descending paths. Our observed LOS change data indicated more active and larger horizontal displacements. The cumulative LOS displacement is up to nearly 300 cm for four years by ALOS and 100 cm for two years by ALOS-2. In addition to InSAR, we performed MAI analysis. MAI is a technique for measuring ground displacement along flight direction, which is not sensitive to the InSAR measurement. The result of MAI showed a few meters displacement and also indicated mostly horizontal displacement. Our preliminary source modeling indicates that a fault with normal faulting and tensile opening could account for the observed LOS changes. The more precise source modeling by simultaneous inversion to explain both the InSAR and MAI displacements is under construction.

Deformation-induced changes in hydraulic head during ground-water withdrawal

USGS Publications Warehouse

Hsieh, Paul A.

1996-01-01

Ground-water withdrawal from a confined or semiconfined aquifer causes three-dimensional deformation in the pumped aquifer and in adjacent layers (overlying and underlying aquifers and aquitards). In response to the deformation, hydraulic head in the adjacent layers could rise or fall almost immediately after the start of pumping. This deformation-induced effect suggest that an adjacent layer undergoes horizontal compression and vertical extension when pumping begins. Hydraulic head initially drops in a region near the well and close to the pumped aquifer, but rises outside this region. Magnitude of head change varies from a few centimeters to more than 10 centimeters. Factors that influence the development of deformation-induced effects includes matrix rigidity (shear modulus), the arrangement of aquifer and aquitards, their thicknesses, and proximity to land surface. Induced rise in hydraulic head is prominent in an aquitard that extends from land surface to a shallow pumped aquifer. Induced drop in hydraulic head is likely observed close to the well in an aquifer that is separated from the pumped aquifer by a relatively thin aquitard. Induced effects might last for hours in an aquifer, but could persist for many days in an aquitard. Induced effects are eventually dissipated by fluid flow from regions of higher head to regions of lower head, and by propagation of drawdown from the pumped aquifer into adjacent layers.

The effects of Vexar® seedling protectors on the growth and development of lodgepole pine roots

USGS Publications Warehouse

Engeman, Richard M.; Anthony, R. Michael; Krupa, Heather W.; Evans, James

1997-01-01

The effects on the growth and development of lodgepole pine roots from the Vexar® tubes used to protect seedlings from pocket gopher damage were studied in the Targhee National Forest, Idaho and the Deschutes National Forest, Oregon. At each site, Vexar-protected and unprotected seedlings, with and without above-ground gopher damage were examined after six growing seasons for root deformities and growth. Undamaged seedlings exhibited greater growth, reflecting the importance of non-lethal gopher damage as a deterrent to tree growth. Protected seedlings with similar damage history as unprotected seedlings had greater root depth than unprotected seedlings, although unprotected seedlings with no above-ground damage generally had the greatest root weight. In general, the percent of seedlings with root deformities was greater for the unprotected seedlings than for the Vexar-protectd seedlings, although this could be largely due to the greater care required to plant protected seedlings. Acute deformities were more common for unprotected seedlings, whereas root deformities with less severe bending were more common for protected seedlings. The incidence of crossed roots was similar for protected and unprotected seedlings on the Deschutes site, where enough occurrences of this deformity permitted analyses. Protected seedlings were similar in root abundance, root distribution, root size and vigor to the unprotected seedlings, with some indication from the Deshutes study site that root distribution was improved with Vexar protection.

An Accurate Co-registration Method for Airborne Repeat-pass InSAR

NASA Astrophysics Data System (ADS)

Dong, X. T.; Zhao, Y. H.; Yue, X. J.; Han, C. M.

2017-10-01

Interferometric Synthetic Aperture Radar (InSAR) technology plays a significant role in topographic mapping and surface deformation detection. Comparing with spaceborne repeat-pass InSAR, airborne repeat-pass InSAR solves the problems of long revisit time and low-resolution images. Due to the advantages of flexible, accurate, and fast obtaining abundant information, airborne repeat-pass InSAR is significant in deformation monitoring of shallow ground. In order to getting precise ground elevation information and interferometric coherence of deformation monitoring from master and slave images, accurate co-registration must be promised. Because of side looking, repeat observing path and long baseline, there are very different initial slant ranges and flight heights between repeat flight paths. The differences of initial slant ranges and flight height lead to the pixels, located identical coordinates on master and slave images, correspond to different size of ground resolution cells. The mismatching phenomenon performs very obvious on the long slant range parts of master image and slave image. In order to resolving the different sizes of pixels and getting accurate co-registration results, a new method is proposed based on Range-Doppler (RD) imaging model. VV-Polarization C-band airborne repeat-pass InSAR images were used in experiment. The experiment result shows that the proposed method leads to superior co-registration accuracy.

Shifts in the eruptive styles at Stromboli in 2010–2014 revealed by ground-based InSAR data

USGS Publications Warehouse

Di Traglia, Federico; Battaglia, Maurizio; Nolesini, Teresa; Lagomarsino, Daniela; Casaglia, Nicola

2015-01-01

Ground-Based Interferometric Synthetic Aperture Radar (GBInSAR) is an efficient technique for capturing short, subtle episodes of conduit pressurization in open vent volcanoes like Stromboli (Italy), because it can detect very shallow magma storage, which is difficult to identify using other methods. This technique allows the user to choose the optimal radar location for measuring the most significant deformation signal, provides an exceptional geometrical resolution, and allows for continuous monitoring of the deformation. Here, we present and model ground displacements collected at Stromboli by GBInSAR from January 2010 to August 2014. During this period, the volcano experienced several episodes of intense volcanic activity, culminated in the effusive flank eruption of August 2014. Modelling of the deformation allowed us to estimate a source depth of 482 ± 46 m a.s.l. The cumulative volume change was 4.7 ± 2.6 × 105 m3. The strain energy of the source was evaluated 3–5 times higher than the surface energy needed to open the 6–7 August eruptive fissure. The analysis proposed here can help forecast shifts in the eruptive style and especially the onset of flank eruptions at Stromboli and at similar volcanic systems (e.g. Etna, Piton de La Fournaise, Kilauea).

Shifts in the eruptive styles at Stromboli in 2010-2014 revealed by ground-based InSAR data.

PubMed

Di Traglia, Federico; Battaglia, Maurizio; Nolesini, Teresa; Lagomarsino, Daniela; Casagli, Nicola

2015-09-01

Ground-Based Interferometric Synthetic Aperture Radar (GBInSAR) is an efficient technique for capturing short, subtle episodes of conduit pressurization in open vent volcanoes like Stromboli (Italy), because it can detect very shallow magma storage, which is difficult to identify using other methods. This technique allows the user to choose the optimal radar location for measuring the most significant deformation signal, provides an exceptional geometrical resolution, and allows for continuous monitoring of the deformation. Here, we present and model ground displacements collected at Stromboli by GBInSAR from January 2010 to August 2014. During this period, the volcano experienced several episodes of intense volcanic activity, culminated in the effusive flank eruption of August 2014. Modelling of the deformation allowed us to estimate a source depth of 482 ± 46 m a.s.l. The cumulative volume change was 4.7 ± 2.6 × 10(5) m(3). The strain energy of the source was evaluated 3-5 times higher than the surface energy needed to open the 6-7 August eruptive fissure. The analysis proposed here can help forecast shifts in the eruptive style and especially the onset of flank eruptions at Stromboli and at similar volcanic systems (e.g. Etna, Piton de La Fournaise, Kilauea).

Plastic deformation of a magnesium oxide 001-plane surface produced by cavitation

NASA Technical Reports Server (NTRS)

Hattori, S.; Miyoshi, K.; Buckley, D. H.; Okada, T.

1986-01-01

An investigation was conducted to examine plastic deformation of a cleaved single-crystal magnesium oxide 001-plane surface exposed to cavitation. Cavitation damage experiments were carried out in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (2 mm) to the surface of the cleaved specimen. The dislocation-etch-pit patterns induced by cavitation were examined and compared with that of microhardness indentations. The results revealed that dislocation-etch-pit patterns around hardness indentations contain both screw and edge dislocations, while the etch-pit patterns on the surface exposed to cavitation contain only screw dislocations. During cavitation, deformation occurred in a thin surface layer, accompanied by work-hardening of the ceramic. The row of screw dislocations underwent a stable growth, which was analyzed crystallographically.

The extensional rheology of non-Newtonian materials

NASA Technical Reports Server (NTRS)

Spiegelberg, Stephen H.; Gaudet, Samuel; Mckinley, Gareth H.

1994-01-01

It has been proposed to measure the extensional viscosity function of a non-Newtonian polymer solution in a reduced gravity environment as part of the Advanced Fluid Module. In ground-based extensional measurements, the no-sip boundary condition at solid-fluid interfaces always result in appreciable shear gradients in the test fluid; however the removal of gravitational body forces permits controlled extensional deformation of containerless test samples and the first unambiguous measurements of this kind. Imperative to successful implementation of this experiment is the generation and subsequent deformation of a stable cylindrical column of test fluid. A study of the generation and deformation of liquid bridges demonstrates that Newtonian liquid bridges undergo capillary breakup as anticipated when stretched beyond a critical aspect ratio; non-Newtonian liquid bridges, however, are stabilized by the strain-hardening phenomenon exhibited by these materials. Numerical simulations of Newtonian breakup are compared with experimental results, and show that previous ground-based attempts at measuring the extensional viscosity of Newtonian fluids are of limited accuracy.

Adaptive multiphoton endomicroscopy through a dynamically deformed multicore optical fiber using proximal detection.

PubMed

Warren, Sean C; Kim, Youngchan; Stone, James M; Mitchell, Claire; Knight, Jonathan C; Neil, Mark A A; Paterson, Carl; French, Paul M W; Dunsby, Chris

2016-09-19

This paper demonstrates multiphoton excited fluorescence imaging through a polarisation maintaining multicore fiber (PM-MCF) while the fiber is dynamically deformed using all-proximal detection. Single-shot proximal measurement of the relative optical path lengths of all the cores of the PM-MCF in double pass is achieved using a Mach-Zehnder interferometer read out by a scientific CMOS camera operating at 416 Hz. A non-linear least squares fitting procedure is then employed to determine the deformation-induced lateral shift of the excitation spot at the distal tip of the PM-MCF. An experimental validation of this approach is presented that compares the proximally measured deformation-induced lateral shift in focal spot position to an independent distally measured ground truth. The proximal measurement of deformation-induced shift in focal spot position is applied to correct for deformation-induced shifts in focal spot position during raster-scanning multiphoton excited fluorescence imaging.

Wrinkling and Folding on Patched Elastic Surfaces: Modulation of the Chemistry and Pattern Size of Microwrinkled Surfaces.

PubMed

Nogales, Aurora; Del Campo, Adolfo; Ezquerra, Tiberio A; Rodriguez-Hernández, Juan

2017-06-14

An unconventional strategy is proposed that takes advantage of localized high-deformation areas, referred to as folded wrinkles, to produce microstructured elastic surfaces with precisely controlled pattern dimensions and chemical distribution. For that purpose, elastic PDMS substrates were prestretched to a different extent and oxidized in particular areas using a mask. When the stretching was removed, the PDMS substrate exhibited out-of-plane deformations that largely depend on the applied prestretching. Prestretchings below 100% lead to affine deformations in which the treated areas are buckled. On the contrary, prestretchings above ε >100% prior to surface treatment induce the formation of folded wrinkles on those micrometer-size ultraviolet-ozone (UVO) treated areas upon relaxation. As a result, dual periodic wrinkles were formed due to the alternation of highly deformed (folded) and low deformed (buckled) areas. Our strategy is based on the surface treatment at precise positions upon prestretching of the elastic substrate (PDMS). Additionally, this approach can be used to template the formation of wrinkled surfaces by alternating lines of folded wrinkles (valleys) and low-deformed areas (hills). This effect allowed us to precisely tune the shape and distribution of the UVO exposed areas by varying the prestretching direction. Moreover, the wrinkle characteristics, including period and amplitude, exhibit a direct relation to the dimensions of the patterns present in the mask.

Torsion and Antero-Posterior Bending in the In Vivo Human Tibia Loading Regimes during Walking and Running

PubMed Central

Yang, Peng-Fei; Sanno, Maximilian; Ganse, Bergita; Koy, Timmo; Brüggemann, Gert-Peter; Müller, Lars Peter; Rittweger, Jörn

2014-01-01

Bending, in addition to compression, is recognized to be a common loading pattern in long bones in animals. However, due to the technical difficulty of measuring bone deformation in humans, our current understanding of bone loading patterns in humans is very limited. In the present study, we hypothesized that bending and torsion are important loading regimes in the human tibia. In vivo tibia segment deformation in humans was assessed during walking and running utilizing a novel optical approach. Results suggest that the proximal tibia primarily bends to the posterior (bending angle: 0.15°–1.30°) and medial aspect (bending angle: 0.38°–0.90°) and that it twists externally (torsion angle: 0.67°–1.66°) in relation to the distal tibia during the stance phase of overground walking at a speed between 2.5 and 6.1 km/h. Peak posterior bending and peak torsion occurred during the first and second half of stance phase, respectively. The peak-to-peak antero-posterior (AP) bending angles increased linearly with vertical ground reaction force and speed. Similarly, peak-to-peak torsion angles increased with the vertical free moment in four of the five test subjects and with the speed in three of the test subjects. There was no correlation between peak-to-peak medio-lateral (ML) bending angles and ground reaction force or speed. On the treadmill, peak-to-peak AP bending angles increased with walking and running speed, but peak-to-peak torsion angles and peak-to-peak ML bending angles remained constant during walking. Peak-to-peak AP bending angle during treadmill running was speed-dependent and larger than that observed during walking. In contrast, peak-to-peak tibia torsion angle was smaller during treadmill running than during walking. To conclude, bending and torsion of substantial magnitude were observed in the human tibia during walking and running. A systematic distribution of peak amplitude was found during the first and second parts of the stance phase. PMID:24732724

Torsion and antero-posterior bending in the in vivo human tibia loading regimes during walking and running.

PubMed

Yang, Peng-Fei; Sanno, Maximilian; Ganse, Bergita; Koy, Timmo; Brüggemann, Gert-Peter; Müller, Lars Peter; Rittweger, Jörn

2014-01-01

Bending, in addition to compression, is recognized to be a common loading pattern in long bones in animals. However, due to the technical difficulty of measuring bone deformation in humans, our current understanding of bone loading patterns in humans is very limited. In the present study, we hypothesized that bending and torsion are important loading regimes in the human tibia. In vivo tibia segment deformation in humans was assessed during walking and running utilizing a novel optical approach. Results suggest that the proximal tibia primarily bends to the posterior (bending angle: 0.15°-1.30°) and medial aspect (bending angle: 0.38°-0.90°) and that it twists externally (torsion angle: 0.67°-1.66°) in relation to the distal tibia during the stance phase of overground walking at a speed between 2.5 and 6.1 km/h. Peak posterior bending and peak torsion occurred during the first and second half of stance phase, respectively. The peak-to-peak antero-posterior (AP) bending angles increased linearly with vertical ground reaction force and speed. Similarly, peak-to-peak torsion angles increased with the vertical free moment in four of the five test subjects and with the speed in three of the test subjects. There was no correlation between peak-to-peak medio-lateral (ML) bending angles and ground reaction force or speed. On the treadmill, peak-to-peak AP bending angles increased with walking and running speed, but peak-to-peak torsion angles and peak-to-peak ML bending angles remained constant during walking. Peak-to-peak AP bending angle during treadmill running was speed-dependent and larger than that observed during walking. In contrast, peak-to-peak tibia torsion angle was smaller during treadmill running than during walking. To conclude, bending and torsion of substantial magnitude were observed in the human tibia during walking and running. A systematic distribution of peak amplitude was found during the first and second parts of the stance phase.

Inverse modeling of InSAR and ground leveling data for 3D volumetric strain distribution

NASA Astrophysics Data System (ADS)

Gallardo, L. A.; Glowacka, E.; Sarychikhina, O.

2015-12-01

Wide availability of modern Interferometric Synthetic aperture Radar (InSAR) data have made possible the extensive observation of differential surface displacements and are becoming an efficient tool for the detailed monitoring of terrain subsidence associated to reservoir dynamics, volcanic deformation and active tectonism. Unfortunately, this increasing popularity has not been matched by the availability of automated codes to estimate underground deformation, since many of them still rely on trial-error subsurface model building strategies. We posit that an efficient algorithm for the volumetric modeling of differential surface displacements should match the availability of current leveling and InSAR data and have developed an algorithm for the joint inversion of ground leveling and dInSAR data in 3D. We assume the ground displacements are originated by a stress free-volume strain distribution in a homogeneous elastic media and determined the displacement field associated to an ensemble of rectangular prisms. This formulation is then used to develop a 3D conjugate gradient inversion code that searches for the three-dimensional distribution of the volumetric strains that predict InSAR and leveling surface displacements simultaneously. The algorithm is regularized applying discontinuos first and zero order Thikonov constraints. For efficiency, the resulting computational code takes advantage of the resulting convolution integral associated to the deformation field and some basic tools for multithreading parallelization. We extensively test our algorithm on leveling and InSAR test and field data of the Northwest of Mexico and compare to some feasible geological scenarios of underground deformation.

How to classify plantar plate injuries: parameters from history and physical examination.

PubMed

Nery, Caio; Coughlin, Michael; Baumfeld, Daniel; Raduan, Fernando; Mann, Tania Szejnfeld; Catena, Fernanda

2015-01-01

To find the best clinical parameters for defining and classifying the degree of plantar plate injuries. Sixty-eight patients (100 metatarsophalangeal joints) were classified in accordance with the Arthroscopic Anatomical Classification for plantar plate injuries and were divided into five groups (0 to IV). Their medical files were reviewed and the incidence of each parameter for the respective group was correlated. These parameters were: use of high heels, sports, acute pain, local edema, Mulder's sign, widening of the interdigital space, pain in the head of the corresponding metatarsal, touching the ground, "drawer test", toe grip and toe deformities (in the sagittal, coronal and transversal planes). There were no statistically significant associations between the degree of injury and use of high-heel shoes, sports trauma, pain at the head of the metatarsal, Mulder's sign, deformity in pronation or displacement in the transversal and sagittal planes (although their combination, i.e. "cross toe", showed a statistically significant correlation). Positive correlations with the severity of the injuries were found in relation to initial acute pain, progressive widening of the interdigital space, loss of "touching the ground", positive results from the "drawer test" on the metatarsophalangeal joint, diminished grip strength and toe deformity in supination. The "drawer test" was seen to be the more reliable and precise tool for classifying the degree of plantar plate injury, followed by "touching the ground" and rotational deformities. It is possible to improve the precision of the diagnosis and the predictions of the anatomical classification for plantar plate injuries through combining the clinical history and data from the physical examination.

Using InSAR to Observe Sinkhole Activity in Central Florida

NASA Astrophysics Data System (ADS)

Oliver-Cabrera, T.; Wdowinski, S.; Kruse, S.; Kiflu, H. G.

2017-12-01

Sinkhole collapse in Florida is a major geologic hazard, threatening human life and causing substantial damage to property. Detecting sinkhole deformation before a collapse is an important but difficult task; most techniques used to monitor sinkholes are spatially constrained to relatively small areas (tens to hundred meters). To overcome this limitation, we use Interferometric Synthetic Aperture Radar (InSAR), which is a very useful technique for detecting localized deformation while covering vast areas. InSAR results show localized deformation at several houses and commercial buildings in different locations along the study sites. We use a subsurface imaging technique, ground penetrating radar, to verify sinkhole existence beneath the observed deforming areas.

Holocene Flexural Deformation over the Nile Delta: Evidence from Radar Interferometry

NASA Astrophysics Data System (ADS)

Gebremichael, E.; Sultan, M.; Becker, R.

2017-12-01

Isostatic adjustment and subsequent subsidence and uplift due to sediment and water loading and unloading mechanisms is one of the major factors that produce regional deformational patterns across river deltas. Using 84 Envisat ASAR scenes that were acquired (2004 - 2010) along three tracks and applying Persistent scatterer (PS) radar interferometric techniques, we documented flexural deformational patterns over the entire Nile Delta (length: 186 km; width: 240 km) of Egypt. The passive continental margin of Africa subsided from Jurassic time onwards due to isostatic loading creating an accommodation space and consequently, the deposition of relatively younger sediments on the oceanic crust. In river deltas, the flexural isostasy model dictates that a subsidence in the oceanic crust side should be balanced by a bulge (uplift) in the flanking regions. Using radar interferometry, we were able to identify the flexural deformation pattern and map its spatial extent over the northern and central Nile Delta region. Findings include: (1) the northern Nile Delta region (block) is separated from the southern delta region by an east-west trending, extensively faulted, hinge line that signifies the boundary between two deformational patterns (subsidence and uplift). It separates the highly subsiding (up to 9.8 mm/yr) northern delta block (up to 85 km long) from the nearly stable (0.4 mm/yr; averaged) southern delta block (up to 91 km long). The hinge line marks the end of the passive continental margin of Africa and the beginning of the oceanic crust of the Mediterranean. (2) We mapped the extent of a 20-40 km wide flexural uplift zone to the south of the hinge line. Within the flexural uplift zone (2.5 mm/yr; averaged), there is a gradual increase in uplift rate reaching peak value (up to 7 mm/yr) near the midpoint of the zone. (3) The uplift rate gradually decreases south of the flexure boundary reaching 0.3 mm/yr at the southern periphery of the delta. (4) The flexural deformation pattern is interrupted (replaced by subsidence) in some areas due to local deformation caused by high groundwater extraction rates in western (6 mm/yr) and gas extraction in north central delta (9 mm/yr).

A Comparison of Vertical Deformations Derived from Space-based Gravimetry, Ground-based Sensors, and Model-based Hydrologic Loading over the Western United States

NASA Astrophysics Data System (ADS)

Yin, G.; Forman, B. A.; Loomis, B. D.; Luthcke, S. B.

2017-12-01

Vertical deformation of the Earth's crust due to the movement and redistribution of terrestrial freshwater can be studied using satellite measurements, ground-based sensors, hydrologic models, or a combination thereof. This current study explores the relationship between vertical deformation estimates derived from mass concentrations (mascons) from the Gravity Recovery and Climate Experiment (GRACE), vertical deformation from ground-based Global Positioning System (GPS) observations collected from the Plate Boundary Observatory (PBO), and hydrologic loading estimates based on model output from the NASA Catchment Land Surface Model (Catchment). A particular focus is made to snow-dominated basins where mass accumulates during the snow season and subsequently runs off during the ablation season. The mean seasonal cycle and the effects of atmospheric loading, non-tidal ocean loading, and glacier isostatic adjustment (GIA) are removed from the GPS observations in order to derive the vertical displacement caused predominately by hydrological processes. A low-pass filter is applied to GPS observations to remove high frequency noise. Correlation coefficients between GRACE- and GPS-based estimates at all PBO sites are calculated. GRACE-derived and Catchment-derived displacements are subtracted from the GPS height variations, respectively, in order to compute the root mean square (RMS) reduction as a means of studying the consistency between the three different methods. Results show that in most sites, the three methods exhibit good agreement. Exceptions to this generalization include the Central Valley of California where extensive groundwater pumping is witnessed in the GRACE- and GPS-based estimates, but not in the Catchment-based estimates because anthropogenic groundwater pumping activities are not included in the Catchment model. The relatively good agreement between GPS- and GRACE-derived vertical crustal displacements suggests that ground-based GPS has tremendous potential for a Bayesian merger with GRACE-based estimates in order to provide a higher resolution (in space and time) of terrestrial water storage.

Experimental estimation of energy absorption during heel strike in human barefoot walking.

PubMed

Baines, Patricia M; Schwab, A L; van Soest, A J

2018-01-01

Metabolic energy expenditure during human gait is poorly understood. Mechanical energy loss during heel strike contributes to this energy expenditure. Previous work has estimated the energy absorption during heel strike as 0.8 J using an effective foot mass model. The aim of our study is to investigate the possibility of determining the energy absorption by more directly estimating the work done by the ground reaction force, the force-integral method. Concurrently another aim is to compare this method of direct determination of work to the method of an effective foot mass model. Participants of our experimental study were asked to walk barefoot at preferred speed. Ground reaction force and lower leg kinematics were collected at high sampling frequency (3000 Hz; 1295 Hz), with tight synchronization. The work done by the ground reaction force is 3.8 J, estimated by integrating this force over the foot-ankle deformation. The effective mass model is improved by dropping the assumption that foot-ankle deformation is maximal at the instant of the impact force peak. On theoretical grounds it is clear that in the presence of substantial damping that peak force and peak deformation do not occur simultaneously. The energy absorption results, due the vertical force only, corresponding to the force-integral method is similar to the results of the improved application of the effective mass model (2.7 J; 2.5 J). However the total work done by the ground reaction force calculated by the force-integral method is significantly higher than that of the vertical component alone. We conclude that direct estimation of the work done by the ground reaction force is possible and preferable over the use of the effective foot mass model. Assuming that energy absorbed is lost, the mechanical energy loss of heel strike is around 3.8 J for preferred walking speeds (≈ 1.3 m/s), which contributes to about 15-20% of the overall metabolic cost of transport.

Application and Evaluation of ALOS PALSAR Data for Monitoring of Mining Induced Surface Deformations Using Interferometric Techniques

NASA Astrophysics Data System (ADS)

Walter, Diana; Wegmuller, Urs; Spreckels, Volker; Busch, Wolfgang

2008-11-01

The main objective of the projects "Determination of ground motions in mining areas by interferometric analyses of ALOS data" (ALOS ADEN 3576, ESA) and "Monitoring of mining induced surface deformation" (ALOS-RA-094, JAXA) is to evaluate PALSAR data for surface deformation monitoring, using interferometric techniques. We present monitoring results of surface movements for an active hard coal colliery of the German hard coal mining company RAG Deutsche Steinkohle (RAG). Underground mining activities lead to ground movements at the surface with maximum subsidence rates of about 10cm per month for the test site. In these projects the L-band sensor clearly demonstrates the good potential for deformation monitoring in active mining areas, especially in rural areas. In comparison to C-band sensors we clearly observe advantages in resolving the high deformation gradients that are present in this area and we achieve a more complete spatial coverage than with C-band. Extensive validation data based on levelling data and GPS measurements are available within RAǴs GIS based database "GeoMon" and thus enable an adequate analysis of the quality of the interferometric results. Previous analyses confirm the good accuracy of PALSAR data for deformation monitoring in mining areas. Furthermore, we present results of special investigations like precision geocoding of PALSAR data and corner reflector analysis. At present only DInSAR results are obtained due to the currently available number of PALSAR scenes. For the future we plan to also apply Persistent Scatterer Interferometry (PSI) using longer series of PALSAR data.

Global link between deformation and volcanic eruption quantified by satellite imagery

PubMed Central

Biggs, J.; Ebmeier, S. K.; Aspinall, W. P.; Lu, Z.; Pritchard, M. E.; Sparks, R. S. J.; Mather, T. A.

2014-01-01

A key challenge for volcanological science and hazard management is that few of the world’s volcanoes are effectively monitored. Satellite imagery covers volcanoes globally throughout their eruptive cycles, independent of ground-based monitoring, providing a multidecadal archive suitable for probabilistic analysis linking deformation with eruption. Here we show that, of the 198 volcanoes systematically observed for the past 18 years, 54 deformed, of which 25 also erupted. For assessing eruption potential, this high proportion of deforming volcanoes that also erupted (46%), together with the proportion of non-deforming volcanoes that did not erupt (94%), jointly represent indicators with ‘strong’ evidential worth. Using a larger catalogue of 540 volcanoes observed for 3 years, we demonstrate how this eruption–deformation relationship is influenced by tectonic, petrological and volcanic factors. Satellite technology is rapidly evolving and routine monitoring of the deformation status of all volcanoes from space is anticipated, meaning probabilistic approaches will increasingly inform hazard decisions and strategic development. PMID:24699342

Global link between deformation and volcanic eruption quantified by satellite imagery.

PubMed

Biggs, J; Ebmeier, S K; Aspinall, W P; Lu, Z; Pritchard, M E; Sparks, R S J; Mather, T A

2014-04-03

A key challenge for volcanological science and hazard management is that few of the world's volcanoes are effectively monitored. Satellite imagery covers volcanoes globally throughout their eruptive cycles, independent of ground-based monitoring, providing a multidecadal archive suitable for probabilistic analysis linking deformation with eruption. Here we show that, of the 198 volcanoes systematically observed for the past 18 years, 54 deformed, of which 25 also erupted. For assessing eruption potential, this high proportion of deforming volcanoes that also erupted (46%), together with the proportion of non-deforming volcanoes that did not erupt (94%), jointly represent indicators with 'strong' evidential worth. Using a larger catalogue of 540 volcanoes observed for 3 years, we demonstrate how this eruption-deformation relationship is influenced by tectonic, petrological and volcanic factors. Satellite technology is rapidly evolving and routine monitoring of the deformation status of all volcanoes from space is anticipated, meaning probabilistic approaches will increasingly inform hazard decisions and strategic development.

Stress and deformation characteristics of sea ice in a high resolution numerical sea ice model.

NASA Astrophysics Data System (ADS)

Heorton, Harry; Feltham, Daniel; Tsamados, Michel

2017-04-01

The drift and deformation of sea ice floating on the polar oceans is due to the applied wind and ocean currents. The deformations of sea ice over ocean basin length scales have observable patterns; cracks and leads in satellite images and within the velocity fields generated from floe tracking. In a climate sea ice model the deformation of sea ice over ocean basin length scales is modelled using a rheology that represents the relationship between stresses and deformation within the sea ice cover. Here we investigate the link between observable deformation characteristics and the underlying internal sea ice stresses and force balance using the Los Alamos numerical sea ice climate model. In order to mimic laboratory experiments on the deformation of small cubes of sea ice we have developed an idealised square domain that tests the model response at spatial resolutions of up to 500m. We use the Elastic Anisotropic Plastic and Elastic Viscous Plastic rheologies, comparing their stability over varying resolutions and time scales. Sea ice within the domain is forced by idealised winds in order to compare the confinement of wind stresses and internal sea ice stresses. We document the characteristic deformation patterns of convergent, divergent and rotating stress states.

Dike Intrusion Process of 2000 Miyakejima - Kozujima Event estimated from GPS measurements in Kozujima - Niijima Islands, central Japan

NASA Astrophysics Data System (ADS)

Murase, M.; Nakao, S.; Kato, T.; Tabei, T.; Kimata, F.; Fujii, N.

2003-12-01

Kozujima - Niijima Islands of Izu Volcano Islands are located about 180 km southeast of Tokyo, Japan. Although the last volcano eruptions in Kozujima and Niijima volcanoes are recorded more than 1000 year before, the ground deformation of 2-3 cm is detected at Kozujima - Niijima Islands by GPS measurements since 1996. On June 26, 2000, earthquake swarm and large ground deformation more than 20 cm are observed at Miyakejima volcano located 40 km east-southeastward of Kozu Island, and volcano eruption are continued since July 7. Remarkable earthquake swarm including five earthquakes more than M5 is stretching to Kozushima Island from Miyakejima Island. From the rapid ground deformation detected by continuous GPS measurements at Miyakejima Island on June 26, magma intrusion models of two or three dikes are discussed in the south and west part of Miyakejima volcano by Irwan et al.(2003) and Ueda et al.(2003). They also estimate dike intrusions are propagated from southern part of Miyakejima volcano to western part, and finally dike intrusion is stretching to 20 km distance toward Kozujima Island. From the ground deformation detected by GPS daily solution of Nation-wide dense GPS network (GEONET), some dike intrusion models are discussed. Ito et al.(2002) estimate the huge dike intrusion with length of about 20 km and volume of 1 km3 in the sea area between the Miyake Island and Kozu Island. (And) Nishimura et al.(2001) introduce not only dike but also aseismic creep source to explain the deformation in Shikinejima. Yamaoka et al.(2002) discuss the dike and spherical deflation source under the dike, because of no evidence supported large aseismic creep. They indicate a dike and spherical deflation source model is as good as dike and creep source model. In case of dike and creep, magma supply is only from the chamber under the Miyakejima volcano. In dike and spherical deflation source model, magma supply is from under Miyakejima volcano and under the dike. Furuya et al.(2003) discuss the gravity change of Miyakejima and they conclude that the magma supply from the chamber under Miyakejima volcano is too small to explain the dike intrusion. In order to discuss the local ground deformation, Nagoya University additionally operates the local GPS network of single frequency receivers at seven sites in Kozujima, Shikineshima and Niijima. Form the vertical deformation detected on local GPS network, northward tilting is observed in Kozujima. We used Genetic Algorithm (GA) for search the model parameter of dike intrusion and fault. GA is an attractive global search tool suitable for the irregular, multimodal fitness functions typically observed in nonlinear optimization problems. We discuss mechanism of Miyakejima - Kozujima event in detail using data of 20 GPS sites near field by GA. The results suggest that magma intrusion system of the dike between Miyakejima and Kozujima changes on August 18 when a large volcano eruption occurred. Until August 18 the activity of creep fault is high and after then deflation at the point source just under the dike is active.

Complex rupture mechanism and topography control symmetry of mass-wasting pattern, 2010 Haiti earthquake

NASA Astrophysics Data System (ADS)

Gorum, Tolga; van Westen, Cees J.; Korup, Oliver; van der Meijde, Mark; Fan, Xuanmei; van der Meer, Freek D.

2013-02-01

The 12 January 2010 Mw 7.0 Haiti earthquake occurred in a complex deformation zone at the boundary between the North American and Caribbean plates. Combined geodetic, geological and seismological data posited that surface deformation was driven by rupture on the Léogâne blind thrust fault, while part of the rupture occurred as deep lateral slip on the Enriquillo-Plantain Garden Fault (EPGF). The earthquake triggered > 4490 landslides, mainly shallow, disrupted rock falls, debris-soil falls and slides, and a few lateral spreads, over an area of ~ 2150 km2. The regional distribution of these slope failures defies those of most similar earthquake-triggered landslide episodes reported previously. Most of the coseismic landslides did not proliferate in the hanging wall of the main rupture, but clustered instead at the junction of the blind Léogâne and EPGF ruptures, where topographic relief and hillslope steepness are above average. Also, low-relief areas subjected to high coseismic uplift were prone to lesser hanging wall slope instability than previous studies would suggest. We argue that a combined effect of complex rupture dynamics and topography primarily control this previously rarely documented landslide pattern. Compared to recent thrust fault-earthquakes of similar magnitudes elsewhere, we conclude that lower static stress drop, mean fault displacement, and blind ruptures of the 2010 Haiti earthquake resulted in fewer, smaller, and more symmetrically distributed landslides than previous studies would suggest. Our findings caution against overly relying on across-the-board models of slope stability response to seismic ground shaking.

Reliability of calculation of the lithosphere deformations in tectonically stable area of Poland based on the GPS measurements

NASA Astrophysics Data System (ADS)

Araszkiewicz, Andrzej; Jarosiński, Marek

2013-04-01

In this research we aimed to check if the GPS observations can be used for calculation of a reliable deformation pattern of the intracontinental lithosphere in seismically inactive areas, such as territory of Poland. For this purpose we have used data mainly from the ASG-EUPOS permanent network and the solutions developed by the MUT CAG team (Military University of Technology: Centre of Applied Geomatics). From the 128 analyzed stations almost 100 are mounted on buildings. Daily observations were processed in the Bernese 5.0 software and next the weekly solutions were used to determine the station velocities expressed in ETRF2000. The strain rates were determined for almost 200 triangles with GPS stations in their corners plotted used Delaunay triangulation. The obtained scattered directions of deformations and highly changeable values of strain rates point to insufficient antennas' stabilization as for geodynamical studies. In order to depict badly stabilized stations we carried out a benchmark test to show what might be the effect of one station drift on deformations in contacting triangles. Based on the benchmark results, from our network we have eliminated the stations which showed deformation pattern characteristic for instable station. After several rounds of strain rate calculations and eliminations of dubious points we have reduced the number of stations down to 60. The refined network revealed more consistent deformation pattern across Poland. Deformations compared with the recent stress field of the study area disclosed good correlation in some places and significant discrepancies in the others, which will be the subject of future research.

Polyethylene damage and deformation on fixed-bearing, non-conforming unicondylar knee replacements corresponding to progressive changes in alignment and fixation.

PubMed

Harman, Melinda K; Schmitt, Sabine; Rössing, Sven; Banks, Scott A; Sharf, Hans-Peter; Viceconti, Marco; Hodge, W Andrew

2010-07-01

Deviations from nominal alignment of unicondylar knee replacements impact knee biomechanics, including the load and stress distribution at the articular contact surfaces. This study characterizes relationships between the biomechanical environment, distinguished by progressive changes in alignment and fixation, and articular damage and deformation in a consecutive series of retrieved unicondylar knee replacements. Twenty seven fixed-bearing, non-conforming unicondylar knee replacements of one design were retrieved after 2 to 13 years of in vivo function. The in vivo biomechanical environment was characterized by grading component migration measured from full-length radiographs and grading component fixation based on intraoperative manual palpation. Articular damage patterns and linear deformation on the polyethylene inserts were measured using optical photogrammetry and contact point digitization. Articular damage patterns and surface deformation on the explanted polyethylene inserts corresponded to progressive changes in component alignment and fixation. Component migration produced higher deformation rates, whereas loosening contributed to larger damage areas but lower deformation rates. Migration and loosening of the femoral component, but not the tibial component, were factors contributing to large regions of abrasion concentrated on the articular periphery. Classifying component migration and fixation at revision proved useful for distinguishing common biomechanical conditions associated with the varied polyethylene damage patterns and linear deformation for this fixed-bearing, non-conforming design. Pre-clinical evaluations of unicondylar knee replacements that are capable of reproducing variations in clinical alignment and predicting the observed wear mechanisms are necessary to better understand the impact of knee biomechanics and design on unicondylar knee replacement longevity. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Design of Rock Slope Reinforcement: An Himalayan Case Study

NASA Astrophysics Data System (ADS)

Tiwari, Gaurav; Latha, Gali Madhavi

2016-06-01

The stability analysis of the two abutment slopes of a railway bridge proposed at about 359 m above the ground level, crossing a river and connecting two hill faces in the Himalayas, India, is presented. The bridge is located in a zone of high seismic activity. The rock slopes are composed of a heavily jointed rock mass and the spacing, dip and dip direction of joint sets are varying at different locations. Geological mapping was carried out to characterize all discontinuities present along the slopes. Laboratory and field investigations were conducted to assess the geotechnical properties of the intact rock, rock mass and joint infill. Stability analyses of these rock slopes were carried out using numerical programmes. Loads from the foundations resting on the slopes and seismic accelerations estimated from site-specific ground response analysis were considered. The proposed slope profile with several berms between successive foundations was simulated in the numerical model. An equivalent continuum approach with Hoek and Brown failure criterion was initially used in a finite element model to assess the global stability of the slope abutments. In the second stage, finite element analysis of rock slopes with all joint sets with their orientations, spacing and properties explicitly incorporated into the numerical model was taken up using continuum with joints approach. It was observed that the continuum with joints approach was able to capture the local failures in some of the slope sections, which were verified using wedge failure analysis and stereographic projections. Based on the slope deformations and failure patterns observed from the numerical analyses, rock anchors were designed to achieve the target factors of safety against failure while keeping the deformations within the permissible limits. Detailed design of rock anchors and comparison of the stability of slopes with and without reinforcement are presented.

Using the two-way shape memory effect of NiTi to control surface texture for cellular mechanotransduction

NASA Astrophysics Data System (ADS)

Liang, Yuan; Qin, Haifeng; Hou, Xiaoning; Doll, Gary L.; Ye, Chang; Dong, Yalin

2018-07-01

Mechanical force can crucially affect form and function of cells, and play critical roles in many diseases. While techniques to conveniently apply mechanical force to cells are limited, we fabricate a surface actuator prototype for cellular mechanotransduction by imparting severe plastic deformation into the surface of shape memory alloy (SMA). Using ultrasonic nanocrystal surface modification (UNSM), a deformation-based surface engineering technique with high controllability, micro surface patterns can be generated on the surface of SMA so that the micro-size cell can conform to the pattern; meanwhile, phase transformation can be induced in the subsurface by severe plastic deformation. By controlling plastic deformation and phase transformation, it is possible to establish a quantitative relation between deformation and temperature. When cells are cultured on the UNSM-treated surface, such surface can dynamically deform in response to external temperature change, and therefore apply controllable mechanical force to cells. Through this study, we demonstrate a novel way to fabricate a low-cost surface actuator that has the potential to be used for high-throughput cellular mechanotransduction.

Volcano geodesy in the Cascade arc, USA

NASA Astrophysics Data System (ADS)

Poland, Michael P.; Lisowski, Michael; Dzurisin, Daniel; Kramer, Rebecca; McLay, Megan; Pauk, Ben

2017-08-01

Experience during historical time throughout the Cascade arc and the lack of deep-seated deformation prior to the two most recent eruptions of Mount St. Helens might lead one to infer that Cascade volcanoes are generally quiescent and, specifically, show no signs of geodetic change until they are about to erupt. Several decades of geodetic data, however, tell a different story. Ground- and space-based deformation studies have identified surface displacements at five of the 13 major Cascade arc volcanoes that lie in the USA (Mount Baker, Mount St. Helens, South Sister, Medicine Lake, and Lassen volcanic center). No deformation has been detected at five volcanoes (Mount Rainier, Mount Hood, Newberry Volcano, Crater Lake, and Mount Shasta), and there are not sufficient data at the remaining three (Glacier Peak, Mount Adams, and Mount Jefferson) for a rigorous assessment. In addition, gravity change has been measured at two of the three locations where surveys have been repeated (Mount St. Helens and Mount Baker show changes, while South Sister does not). Broad deformation patterns associated with heavily forested and ice-clad Cascade volcanoes are generally characterized by low displacement rates, in the range of millimeters to a few centimeters per year, and are overprinted by larger tectonic motions of several centimeters per year. Continuous GPS is therefore the best means of tracking temporal changes in deformation of Cascade volcanoes and also for characterizing tectonic signals so that they may be distinguished from volcanic sources. Better spatial resolution of volcano deformation can be obtained through the use of campaign GPS, semipermanent GPS, and interferometric synthetic aperture radar observations, which leverage the accumulation of displacements over time to improve signal to noise. Deformation source mechanisms in the Cascades are diverse and include magma accumulation and withdrawal, post-emplacement cooling of recent volcanic deposits, magmatic-tectonic interactions, and loss of volatiles plus densification of magma. The Cascade Range thus offers an outstanding opportunity for investigating a wide range of volcanic processes. Indeed, there may be areas of geodetic change that have yet to be discovered, and there is good potential for addressing a number of important questions about how arc volcanoes work before, during, and after eruptions by continuing geodetic research in the Cascade Range.

Volcano geodesy in the Cascade arc, USA

USGS Publications Warehouse

Poland, Michael; Lisowski, Michael; Dzurisin, Daniel; Kramer, Rebecca; McLay, Megan; Pauk, Benjamin

2017-01-01

Experience during historical time throughout the Cascade arc and the lack of deep-seated deformation prior to the two most recent eruptions of Mount St. Helens might lead one to infer that Cascade volcanoes are generally quiescent and, specifically, show no signs of geodetic change until they are about to erupt. Several decades of geodetic data, however, tell a different story. Ground- and space-based deformation studies have identified surface displacements at five of the 13 major Cascade arc volcanoes that lie in the USA (Mount Baker, Mount St. Helens, South Sister, Medicine Lake, and Lassen volcanic center). No deformation has been detected at five volcanoes (Mount Rainier, Mount Hood, Newberry Volcano, Crater Lake, and Mount Shasta), and there are not sufficient data at the remaining three (Glacier Peak, Mount Adams, and Mount Jefferson) for a rigorous assessment. In addition, gravity change has been measured at two of the three locations where surveys have been repeated (Mount St. Helens and Mount Baker show changes, while South Sister does not). Broad deformation patterns associated with heavily forested and ice-clad Cascade volcanoes are generally characterized by low displacement rates, in the range of millimeters to a few centimeters per year, and are overprinted by larger tectonic motions of several centimeters per year. Continuous GPS is therefore the best means of tracking temporal changes in deformation of Cascade volcanoes and also for characterizing tectonic signals so that they may be distinguished from volcanic sources. Better spatial resolution of volcano deformation can be obtained through the use of campaign GPS, semipermanent GPS, and interferometric synthetic aperture radar observations, which leverage the accumulation of displacements over time to improve signal to noise. Deformation source mechanisms in the Cascades are diverse and include magma accumulation and withdrawal, post-emplacement cooling of recent volcanic deposits, magmatic-tectonic interactions, and loss of volatiles plus densification of magma. The Cascade Range thus offers an outstanding opportunity for investigating a wide range of volcanic processes. Indeed, there may be areas of geodetic change that have yet to be discovered, and there is good potential for addressing a number of important questions about how arc volcanoes work before, during, and after eruptions by continuing geodetic research in the Cascade Range.

Comparison of performance of inclinometer casing and TDR technique

NASA Astrophysics Data System (ADS)

Aghda, S. M. Fatemi; Ganjalipour, K.; Nabiollahi, K.

2018-03-01

TDR (Time Domain Reflectometry) and GPR (Ground Penetrating Radar) are two of the electromagnetic methods in applied geophysics, which using them for various applications are developing. The Time Domain Reflectometry is a remote sensing method that has been used for years to determine the nature of the materials and spatial location. The use of TDR system has led to innovative applications of it and comparing it with previous measuring techniques, since it has developed. In this study, not only a summary of the basics of TDR application for monitoring of ground deformation is offered, but also a comparison of this technology with other measurement techniques (inclinometer casing) is provided. Actually, this paper presents a case study in which the opportunity arose to compare these two technologies in detecting subsurface deformation in slopes. A TDR system includes a radar wave receiver & generator, a transmission line and a waveguide. The generated electro-magnetic pulse moves toward the waveguide within the conductor cable and enters the test environment. For this study, slopes overlooking the Darian dam bottom outlet, power house and spillway were instrumented with RG59/U coaxial cables for TDR monitoring and slope inclinometer. Coaxial cables - as a TDR sensor - and inclinometer casings were installed in a same bore hole where coaxial cable was attached to the inclinometer casing. Shear and tensile deformations of the cable, which is caused by ground movements, significantly impacts on cable reflection coefficient. In Darian dam boreholes, the cable points subject to the shear and stretch were correlated with deformation points of the inclinometer casings in incremental displacement graphs. This study shows that TDR technique is more sensitive than inclinometer casing for small movement in the slide planes. Because manual processing of TDR data is hard and need experienced personnel, the authors have designed an algorithm to compare the shape of the new TDR waveforms with the base reading waveform in order to monitor the subsurface deformations.

Contour junctions defined by dynamic image deformations enhance perceptual transparency.

PubMed

Kawabe, Takahiro; Nishida, Shin'ya

2017-11-01

The majority of work on the perception of transparency has focused on static images with luminance-defined contour junctions, but recent work has shown that dynamic image sequences with dynamic image deformations also provide information about transparency. The present study demonstrates that when part of a static image is dynamically deformed, contour junctions at which deforming and nondeforming contours are connected facilitate the deformation-based perception of a transparent layer. We found that the impression of a transparent layer was stronger when a dynamically deforming area was adjacent to static nondeforming areas than when presented alone. When contour junctions were not formed at the dynamic-static boundaries, however, the impression of a transparent layer was not facilitated by the presence of static surrounding areas. The effect of the deformation-defined junctions was attenuated when the spatial pattern of luminance contrast at the junctions was inconsistent with the perceived transparency related to luminance contrast, while the effect did not change when the spatial luminance pattern was consistent with it. In addition, the results showed that contour completions across the junctions were required for the perception of a transparent layer. These results indicate that deformation-defined junctions that involve contour completion between deforming and nondeforming regions enhance the perception of a transparent layer, and that the deformation-based perceptual transparency can be promoted by the simultaneous presence of appropriately configured luminance and contrast-other features that can also by themselves produce the sensation of perceiving transparency.

Imaging Basal Crevasses at the Grounding Line of Whillans Ice Stream, West Antarctica

NASA Astrophysics Data System (ADS)

Jacobel, R. W.; Dawson, E. C.; Christianson, K.

2015-12-01

We acquired gridded ground-based radar data at the WIS grounding zone where the transition from limited- or no-slip conditions at the base of grounded ice to free-slip conditions beneath floating ice occurs across a region only a few kilometers wide. This transition is either an elastic-flexural transition from bedrock to hydrostatically-supported elevations (often tidally influenced), a transition from thicker to thinner ice over a flat bed, or some combination of these. In either case, the stress field of the ice changes as it flows across the grounding zone, often resulting in brittle deformation, which is manifested as basal crevassing at the ice-sheet base and sometimes as strand cracks at the surface. The position and morphology of these features reveal important information about the stress state across this transition where ice and ocean interact. Our surveys indicate a complex pattern of basal crevassing with many imaged in two or more profile segments as a linear feature at the bed, usually trending oblique to flow and often extending for several kilometers. Due to the wide beam pattern of our antennas, we image many of the crevasses from off-nadir reflections. Thus their arrival times are later than the primary basal reflection and segments of the crevasse appear "below" the bed, when in fact they are merely trending oblique to the profile. Often these returns have a reversed phase relative to the bed echo because the high dielectric contrast of seawater and a favorable geometry enable reflections with little loss (but a second phase reversal) from the ice-water interface near the crevasse base. In a few cases, these crevasse echoes from targets trending oblique to the profile appear to mimic the geometry of a sub-ice sediment "wedge", while in reality the radar never penetrates below the basal interface. Only about 25% of the crevasses appear to extend any significant distance upward into the basal ice, typically at low angles. A subset of these are doubly imaged by direct returns as well as by delayed reflections from the bright planar basal interface, giving curious mirror-like signatures. Our results indicate that basal crevasses offer a rich dataset for diagnosing basal stress state across ice-sheet grounding zones and that special care is needed when interpreting subglacial returns in radar data.

Eliminating the zero spectrum in Fourier transform profilometry using empirical mode decomposition.

PubMed

Li, Sikun; Su, Xianyu; Chen, Wenjing; Xiang, Liqun

2009-05-01

Empirical mode decomposition is introduced into Fourier transform profilometry to extract the zero spectrum included in the deformed fringe pattern without the need for capturing two fringe patterns with pi phase difference. The fringe pattern is subsequently demodulated using a standard Fourier transform profilometry algorithm. With this method, the deformed fringe pattern is adaptively decomposed into a finite number of intrinsic mode functions that vary from high frequency to low frequency by means of an algorithm referred to as a sifting process. Then the zero spectrum is separated from the high-frequency components effectively. Experiments validate the feasibility of this method.

Image Correlation Pattern Optimization for Micro-Scale In-Situ Strain Measurements

NASA Technical Reports Server (NTRS)

Bomarito, G. F.; Hochhalter, J. D.; Cannon, A. H.

2016-01-01

The accuracy and precision of digital image correlation (DIC) is a function of three primary ingredients: image acquisition, image analysis, and the subject of the image. Development of the first two (i.e. image acquisition techniques and image correlation algorithms) has led to widespread use of DIC; however, fewer developments have been focused on the third ingredient. Typically, subjects of DIC images are mechanical specimens with either a natural surface pattern or a pattern applied to the surface. Research in the area of DIC patterns has primarily been aimed at identifying which surface patterns are best suited for DIC, by comparing patterns to each other. Because the easiest and most widespread methods of applying patterns have a high degree of randomness associated with them (e.g., airbrush, spray paint, particle decoration, etc.), less effort has been spent on exact construction of ideal patterns. With the development of patterning techniques such as microstamping and lithography, patterns can be applied to a specimen pixel by pixel from a patterned image. In these cases, especially because the patterns are reused many times, an optimal pattern is sought such that error introduced into DIC from the pattern is minimized. DIC consists of tracking the motion of an array of nodes from a reference image to a deformed image. Every pixel in the images has an associated intensity (grayscale) value, with discretization depending on the bit depth of the image. Because individual pixel matching by intensity value yields a non-unique scale-dependent problem, subsets around each node are used for identification. A correlation criteria is used to find the best match of a particular subset of a reference image within a deformed image. The reader is referred to references for enumerations of typical correlation criteria. As illustrated by Schreier and Sutton and Lu and Cary systematic errors can be introduced by representing the underlying deformation with under-matched shape functions. An important implication, as discussed by Sutton et al., is that in the presence of highly localized deformations (e.g., crack fronts), error can be reduced by minimizing the subset size. In other words, smaller subsets allow the more accurate resolution of localized deformations. Contrarily, the choice of optimal subset size has been widely studied and a general consensus is that larger subsets with more information content are less prone to random error. Thus, an optimal subset size balances the systematic error from under matched deformations with random error from measurement noise. The alternative approach pursued in the current work is to choose a small subset size and optimize the information content within (i.e., optimizing an applied DIC pattern), rather than finding an optimal subset size. In the literature, many pattern quality metrics have been proposed, e.g., sum of square intensity gradient (SSSIG), mean subset fluctuation, gray level co-occurrence, autocorrelation-based metrics, and speckle-based metrics. The majority of these metrics were developed to quantify the quality of common pseudo-random patterns after they have been applied, and were not created with the intent of pattern generation. As such, it is found that none of the metrics examined in this study are fit to be the objective function of a pattern generation optimization. In some cases, such as with speckle-based metrics, application to pixel by pixel patterns is ill-conditioned and requires somewhat arbitrary extensions. In other cases, such as with the SSSIG, it is shown that trivial solutions exist for the optimum of the metric which are ill-suited for DIC (such as a checkerboard pattern). In the current work, a multi-metric optimization method is proposed whereby quality is viewed as a combination of individual quality metrics. Specifically, SSSIG and two auto-correlation metrics are used which have generally competitive objectives. Thus, each metric could be viewed as a constraint imposed upon the others, thereby precluding the achievement of their trivial solutions. In this way, optimization produces a pattern which balances the benefits of multiple quality metrics. The resulting pattern, along with randomly generated patterns, is subjected to numerical deformations and analyzed with DIC software. The optimal pattern is shown to outperform randomly generated patterns.

Running and Breathing in Mammals

NASA Astrophysics Data System (ADS)

Bramble, Dennis M.; Carrier, David R.

1983-01-01

Mechanical constraints appear to require that locomotion and breathing be synchronized in running mammals. Phase locking of limb and respiratory frequency has now been recorded during treadmill running in jackrabbits and during locomotion on solid ground in dogs, horses, and humans. Quadrupedal species normally synchronize the locomotor and respiratory cycles at a constant ratio of 1:1 (strides per breath) in both the trot and gallop. Human runners differ from quadrupeds in that while running they employ several phase-locked patterns (4:1, 3:1, 2:1, 1:1, 5:2, and 3:2), although a 2:1 coupling ratio appears to be favored. Even though the evolution of bipedal gait has reduced the mechanical constraints on respiration in man, thereby permitting greater flexibility in breathing pattern, it has seemingly not eliminated the need for the synchronization of respiration and body motion during sustained running. Flying birds have independently achieved phase-locked locomotor and respiratory cycles. This hints that strict locomotor-respiratory coupling may be a vital factor in the sustained aerobic exercise of endothermic vertebrates, especially those in which the stresses of locomotion tend to deform the thoracic complex.

Effective field theory for triaxially deformed nuclei

NASA Astrophysics Data System (ADS)

Chen, Q. B.; Kaiser, N.; Meißner, Ulf-G.; Meng, J.

2017-10-01

Effective field theory is generalized to investigate the rotational motion of triaxially deformed even-even nuclei. The Hamiltonian for the triaxial rotor is obtained up to next-to-leading order within the effective field theory formalism. Its applicability is examined by comparing with a five-dimensional rotor-vibrator Hamiltonian for the description of the energy spectra of the ground state and γ band in Ru isotopes. It is found that by taking into account the next-to-leading order corrections, the ground state band in the whole spin region and the γ band in the low spin region are well described. The deviations for high-spin states in the γ bands point towards the importance of including vibrational degrees of freedom in the effective field theory formulation.

Anharmonic vibrations around a triaxial nuclear deformation “frozen” to γ = 30°

DOE Office of Scientific and Technical Information (OSTI.GOV)

Buganu, Petrica, E-mail: buganu@theory.nipne.ro; Budaca, Radu

2015-12-07

The Davydov-Chaban Hamiltonian with a sextic oscillator potential for the variable β and γ fixed to 30° is exactly solved for the ground and β bands and approximately for the γ band. The model is called Z(4)-Sextic in connection with the already established Z(4) solution. The energy spectra, normalized to the energy of the first excited state, and several B(E2) transition probabilities, normalized to the B(E2) transition from the first excited state to the ground state, depend on a single parameter α. By varying α within a sufficiently large interval, a shape phase transition from an approximately spherical shape tomore » a deformed one is evidenced.« less

Exciting (and modulating) very-long-period seismic signals on White Island, New Zealand

NASA Astrophysics Data System (ADS)

Neuberg, Jurgen; Jolly, Art

2014-05-01

Very-long-period seismic signals (VLP) on volcanoes can be used to fill the gap between classic seismology and deformation studies. In this contribution we reiterate the principal processing steps to retrieve from a velocity seismogram 3D ground displacement with tiny amplitudes far beyond the resolution of GPS. As a case study we use several seismic and infrasonic signals of volcanic events from White Island, New Zealand. We apply particle motion analysis and deformation modelling tools to the resulting displacement signals and exam the potential link between ground displacement and the modulation of harmonic tremor, in turn linked to a hydrothermal system. In this way we want to demonstrate the full potential of VLPs in monitoring and modelling of volcanic processes.

The influence on the interferometry due to the instability of ground-based synthetic aperture radar work platform

NASA Astrophysics Data System (ADS)

Tao, Gang; Wei, Guohua; Wang, Xu; Kong, Ming

2018-03-01

There has been increased interest over several decades for applying ground-based synthetic aperture radar (GB-SAR) for monitoring terrain displacement. GB-SAR can achieve multitemporal surface deformation maps of the entire terrain with high spatial resolution and submilimetric accuracy due to the ability of continuous monitoring a certain area day and night regardless of the weather condition. The accuracy of the interferometric measurement result is very important. In this paper, the basic principle of InSAR is expounded, the influence of the platform's instability on the interferometric measurement results are analyzed. The error sources of deformation detection estimation are analyzed using precise geometry of imaging model. Finally, simulation results demonstrates the validity of our analysis.

Digital Elevation Models of Patterned Ground in the Canadian Arctic and Implications for the Study of Mars

NASA Astrophysics Data System (ADS)

Knightly, P.; Murakami, Y.; Clarke, J.; Sizemore, H.; Siegler, M.; Rupert, S.; Chevrier, V.

2017-12-01

Patterned ground forms in periglacial zones from both expansion and contraction of permafrost by freeze-thaw and sub-freezing temperature changes and has been observed on both Earth and Mars from orbital and the surface at the Phoneix and Viking 2 landing sites. The Phoenix mission to Mars studied patterned ground in the vicinity of the spacecraft including the excavation of a trench revealing water permafrost beneath the surface. A study of patterned ground at the Haughton Impact structure on Devon Island used stereo-pair imaging and three-dimensional photographic models to catalog the type and occurrence of patterned ground in the study area. This image catalog was then used to provide new insight into photographic observations gathered by Phoenix. Stereo-pair imagery has been a valuable geoscience tool for decades and it is an ideal tool for comparative planetary geology studies. Stereo-pair images captured on Devon Island were turned into digital elevation models (DEMs) and comparisons were noted between the permafrost and patterned ground environment of Earth and Mars including variations in grain sorting, active layer thickness, and ice table depth. Recent advances in 360° cameras also enabled the creation of a detailed, immersive site models of patterned ground at selected sites in Haughton crater on Devon Island. The information from this ground truth study will enable the development and refinement of existing models to better evaluate patterned ground on Mars and predict its evolution.

Fortuna Tessera, Venus - Evidence of horizontal convergence and crustal thickening

NASA Technical Reports Server (NTRS)

Vorder Bruegge, R. W.; Head, J. W.

1989-01-01

Structural and tectonic patterns mapped in Fortuna Tessera are interpreted to reflect a change in the style and intensity of deformation from east to west, beginning with simple tessera terrain at relatively low topographic elevations in the east and progressing through increasingly complex deformation patterns and higher topography to Maxwell Montes in the West. These morphologic and topographic patterns are consistent with east-to-west convergence and compression and the increasing elevations are interpreted to be due to crustal thickening processes associated with the convergent deformational environment. Using an Airy isostatic model, crustal thicknesses of approximately 35 km for the initial tessera terrain, and crustal thicknesses of over 100 km for the Maxwell Montes region are predicted. Detailed mapping with Magellan data will permit the deconvolution of individual components and structures in this terrain.

On the dynamical behaviour of low-frequency earthquake swarms prior to a dome collapse of Soufrière Hill volcano, Montserrat

NASA Astrophysics Data System (ADS)

Hammer, C.; Neuberg, J. W.

2009-03-01

A series of low-frequency earthquake swarms prior to a dome collapse on Soufrière Hills volcano, Montserrat, are investigated with the emphasis on event rate and amplitude behaviour. In a single swarm, the amplitudes of consecutive events tend to increase with time, while the rate of event occurrence accelerates initially and then decelerates toward the end of the swarm. However, when consecutive swarms are considered, the average event rates seem to follow the material failure law, and the time of the dome collapse can be successfully estimated using the inverse event rate. These patterns in amplitude and event rate are interpreted as fluctuations in magma ascent velocity, which result in both the generation of low-frequency events as well as cyclic ground deformation accompanying the swarm activity.

The orientation distribution of tunneling-related quantities

NASA Astrophysics Data System (ADS)

Seif, W. M.; Refaie, A. I.; Botros, M. M.

2018-03-01

In the nuclear tunneling processes involving deformed nuclei, most of the tunneling-related quantities depend on the relative orientations of the participating nuclei. In the presence of different multipole deformations, we study the variation of a few relevant quantities for the α-decay and the sub-barrier fusion processes, in an orientation degree of freedom. The knocking frequency and the penetration probability are evaluated within the Wentzel-Kramers-Brillouin approximation. The interaction potential is calculated with Skyrme-type nucleon-nucleon interaction. We found that the width of the potential pocket, the Coulomb barrier radius, the penetration probability, the α-decay width, and the fusion cross-section follow consistently the orientation-angle variation of the radius of the deformed nucleus. The orientation distribution patterns of the pocket width, the barrier radius, the logarithms of the penetrability, the decay width, and the fusion cross-section are found to be highly analogous to pattern of the deformed-nucleus radius. The curve patterns of the orientation angle distributions of the internal pocket depth, the Coulomb barrier height and width, as well as the knocking frequency simulate inversely the variation of the deformed nucleus radius. The predicted orientation behaviors will be of a special interest in predicting the optimum orientations for the tunneling processes.

Proof-of-feasibility of using well bore deformation as a diagnostic tool to improve CO 2 sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Murdoch, Larry; Moysey, Stephen; Germanovich, Leonid

Injecting CO 2 raises pore pressure and this causes subsurface formations to deform. The pattern and amount of deformation will reflect the distribution of pressure and formation properties in the subsurface, two quantities of interest during CO 2 storage. The hypothesis underlying this research is that the small deformation accompanying CO 2 storage can be measured and interpreted to improve the storage process.

Deformation properties of lead isotopes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tolokonnikov, S. V.; Borzov, I. N.; Lutostansky, Yu. S.

2016-01-15

The deformation properties of a long lead isotopic chain up to the neutron drip line are analyzed on the basis of the energy density functional (EDF) in the FaNDF{sup 0} Fayans form. The question of whether the ground state of neutron-deficient lead isotopes can have a stable deformation is studied in detail. The prediction of this deformation is contained in the results obtained on the basis of the HFB-17 and HFB-27 Skyrme EDF versions and reported on Internet. The present analysis reveals that this is at odds with experimental data on charge radii and magnetic moments of odd lead isotopes.more » The Fayans EDF version predicts a spherical ground state for all light lead isotopes, but some of them (for example, {sup 180}Pb and {sup 184}Pb) prove to be very soft—that is, close to the point of a phase transition to a deformed state. Also, the results obtained in our present study are compared with the predictions of some other Skyrme EDF versions, including SKM*, SLy4, SLy6, and UNE1. By and large, their predictions are closer to the results arising upon the application of the Fayans functional. For example, the SLy4 functional predicts, in just the same way as the FaNDF{sup 0} functional, a spherical shape for all nuclei of this region. The remaining three Skyrme EDF versions lead to a deformation of some light lead isotopes, but their number is substantially smaller than that in the case of the HFB-17 and HFB-27 functionals. Moreover, the respective deformation energy is substantially lower, which gives grounds to hope for the restoration of a spherical shape upon going beyond the mean-field approximation, which we use here. Also, the deformation properties of neutron-rich lead isotopes are studied up to the neutron drip line. Here, the results obtained with the FaNDF{sup 0} functional are compared with the predictions of the HFB-17, HFB-27, SKM*, and SLy4 Skyrme EDF versions. All of the EDF versions considered here predict the existence of a region where neutron-rich lead isotopes undergo deformations, but the size of this region is substantially different for the different functionals being considered. Once again, it is maximal for the HFB-17 and HFB-27 functionals, is substantially narrower for the FaNDF{sup 0} functional, and is still narrower for the SKM* and SLy4 functionals. The two-neutron drip line proved to be A{sub drip}{sup 2n} = 266 for all of the EDF versions considered here, with the exception of SKM*, for which it is shifted to A{sub drip}{sup 2n}(SKM*) = 272.« less

Regional Survey of Structural Properties and Cementation Patterns of Fault Zones in the Northern Part of the Albuquerque Basin, New Mexico - Implications for Ground-Water Flow

USGS Publications Warehouse

Minor, Scott A.; Hudson, Mark R.

2006-01-01

Motivated by the need to document and evaluate the types and variability of fault zone properties that potentially affect aquifer systems in basins of the middle Rio Grande rift, we systematically characterized structural and cementation properties of exposed fault zones at 176 sites in the northern Albuquerque Basin. A statistical analysis of measurements and observations evaluated four aspects of the fault zones: (1) attitude and displacement, (2) cement, (3) lithology of the host rock or sediment, and (4) character and width of distinctive structural architectural components at the outcrop scale. Three structural architectural components of the fault zones were observed: (1) outer damage zones related to fault growth; these zones typically contain deformation bands, shear fractures, and open extensional fractures, which strike subparallel to the fault and may promote ground-water flow along the fault zone; (2) inner mixed zones composed of variably entrained, disrupted, and dismembered blocks of host sediment; and (3) central fault cores that accommodate most shear strain and in which persistent low- permeability clay-rich rocks likely impede the flow of water across the fault. The lithology of the host rock or sediment influences the structure of the fault zone and the width of its components. Different grain-size distributions and degrees of induration of the host materials produce differences in material strength that lead to variations in width, degree, and style of fracturing and other fault-related deformation. In addition, lithology of the host sediment appears to strongly control the distribution of cement in fault zones. Most faults strike north to north-northeast and dip 55? - 77? east or west, toward the basin center. Most faults exhibit normal slip, and many of these faults have been reactivated by normal-oblique and strike slip. Although measured fault displacements have a broad range, from 0.9 to 4,000 m, most are <100 m, and fault zones appear to have formed mainly at depths less than 1,000 m. Fault zone widths do not exceed 40 m (median width = 15.5 m). The mean width of fault cores (0.1 m) is nearly one order of magnitude less than that of mixed zones (0.75 m) and two orders of magnitude less than that of damage zones (9.7 m). Cements, a proxy for localized flow of ancient ground water, are common along fault zones in the basin. Silica cements are limited to faults that are near and strike north to northwest toward the Jemez volcanic field north of the basin, whereas carbonate fault cements are widely distributed. Coarse sediments (gravel and sand) host the greatest concentrations of cement within fault zones. Cements fill some extension fractures and, to a lesser degree, are concentrated along shear fractures and deformation bands within inner damage zones. Cements are commonly concentrated in mixed zones and inner damage zones on one side of a fault and thus are asymmetrically distributed within a fault zone, but cement does not consistently lie on the basinward side of faults. From observed spatial patterns of asymmetrically distributed fault zone cements, we infer that ancient ground-water flow was commonly localized along, and bounded by, faults in the basin. It is apparent from our study that the Albuquerque Basin contains a high concentration of faults. The geometry of, internal structure of, and cement and clay distribution in fault zones have created and will continue to create considerable heterogeneity of permeability within the basin aquifers. The characteristics and statistical range of fault zone features appear to be predictable and consistent throughout the basin; this predictability can be used in ground-water flow simulations that consider the influence of faults.

Response of deformation patterns to reorganizations of the southern San Andreas fault system since ca. 1.5 Ma

NASA Astrophysics Data System (ADS)

Cooke, M. L.; Fattaruso, L.; Dorsey, R. J.; Housen, B. A.

2015-12-01

Between ~1.5 and 1.1 Ma, the southern San Andreas fault system underwent a major reorganization that included initiation of the San Jacinto fault and termination of slip on the extensional West Salton detachment fault. The southern San Andreas fault itself has also evolved since this time, with several shifts in activity among fault strands within San Gorgonio Pass. We use three-dimensional mechanical Boundary Element Method models to investigate the impact of these changes to the fault network on deformation patterns. A series of snapshot models of the succession of active fault geometries explore the role of fault interaction and tectonic loading in abandonment of the West Salton detachment fault, initiation of the San Jacinto fault, and shifts in activity of the San Andreas fault. Interpreted changes to uplift patterns are well matched by model results. These results support the idea that growth of the San Jacinto fault led to increased uplift rates in the San Gabriel Mountains and decreased uplift rates in the San Bernardino Mountains. Comparison of model results for vertical axis rotation to data from paleomagnetic studies reveals a good match to local rotation patterns in the Mecca Hills and Borrego Badlands. We explore the mechanical efficiency at each step in the evolution, and find an overall trend toward increased efficiency through time. Strain energy density patterns are used to identify regions of off-fault deformation and potential incipient faulting. These patterns support the notion of north-to-south propagation of the San Jacinto fault during its initiation. The results of the present-day model are compared with microseismicity focal mechanisms to provide additional insight into the patterns of off-fault deformation within the southern San Andreas fault system.

Meteorite Impact "Earthquake" Features (Rock Liquefaction, Surface Wave Deformations, Seismites) from Ground Penetrating Radar (GPR) and Geoelectric Complex Resistivity/Induced Polarization (IP) Measurements, Chiemgau (Alpine Foreland, Southeast Germany)

NASA Astrophysics Data System (ADS)

Ernstson, K.; Poßekel, J.

2017-12-01

Densely spaced GPR and complex resistivity measurements on a 30,000 square meters site in a region of enigmatic sinkhole occurrences in unconsolidated Quaternary sediments have featured unexpected and highlighting results from both a meteorite impact research and an engineering geology point of view. The GPR measurements and a complex resistivity/IP electrical imaging revealed extended subrosion depressions related with a uniformly but in various degrees of intensity deformed loamy and gravelly ground down to at least 10 m depth. Two principle observations could be made from both the GPR high-resolution measurements and the more integrating resistivity and IP soundings with both petrophysical evidences in good complement. Subrosion can be shown to be the result of prominent sandy-gravelly intrusions and extrusions typical of rock liquefaction processes well known to occur during strong earthquakes. Funnel-shaped structures with diameters up to 25 m near the surface and reaching down to the floating ground water level at 10 m depth were measured. GPR radargrams could trace prominent gravelly-material transport bottom-up within the funnels. Seen in both GPR tomography and resistivity/IP sections more or less the whole investigated area is overprinted by wavy deformations of the unconsolidated sediments with wavelengths of the order of 5 - 10 m and amplitudes up to half a meter, likewise down to 10 m depth. Substantial earthquakes are not known in this region. Hence, the observed heavy underground disorder is considered the result of the prominent earthquake shattering that must have occurred during the Holocene (Bronze Age/Celtic era) Chiemgau meteorite impact event that produced a 60 km x 30 km sized crater strewn field directly hosting the investigated site. Depending on depth and size of floating aquifers local concentrations of rock liquefaction and seismic surface waves (probably LOVE waves) to produce the wavy deformations could develop, when the big disintegrated meteoroid (a loosely bound asteroid or a comet of roughly estimated 1 km size) hit the ground. The observations in the Chiemgau area emphasize that studied paleoliquefaction features and wavy deformations (e.g. seismites) need not necessarily have originated solely from paleoseismicity but can provide a recognizable regional impact signature.

Static Buckling Model Tests and Elasto-plastic Finite Element Analysis of a Pile in Layers with Various Thicknesses

NASA Astrophysics Data System (ADS)

Okajima, Kenji; Imai, Junichi; Tanaka, Tadatsugu; Iida, Toshiaki

Damage to piles in the liquefied ground is frequently reported. Buckling by the excess vertical load could be one of the causes of the pile damage, as well as the lateral flow of the ground and the lateral load at the pile head. The buckling mechanism is described as a complicated interaction between the pile deformation by the vertical load and the earth pressure change cased by the pile deformation. In this study, series of static buckling model tests of a pile were carried out in dried sand ground with various thickness of the layer. Finite element analysis was applied to the test results to verify the effectiveness of the elasto-plastic finite element analysis combining the implicit-explicit mixed type dynamic relaxation method with the return mapping method to the pile buckling problems. The test results and the analysis indicated the possibility that the buckling load of a pile decreases greatly where the thickness of the layer increases.

Sulzberger Ice Shelf Tidal Signal Reconstruction Using InSAR

NASA Astrophysics Data System (ADS)

Baek, S.; Shum, C.; Yi, Y.; Kwoun, O.; Lu, Z.; Braun, A.

2005-12-01

Synthetic Aperture Radar Interferometry (InSAR) and Differential InSAR (DInSAR) have been demonstrated as useful techniques to detect surface deformation over ice sheet and ice shelves over Antarctica. In this study, we use multiple-pass InSAR from the ERS-1 and ERS-2 data to detect ocean tidal deformation with an attempt towards modeling of tides underneath an ice shelf. High resolution Digital Elevation Model (DEM) from repeat-pass interferometry and ICESat profiles as ground control points is used for topographic correction over the study region in Sulzberger Ice Shelf, West Antarctica. Tidal differences measured by InSAR are obtained by the phase difference between a point on the grounded ice and a point on ice shelf. Comparison with global or regional tide models (including NAO, TPXO, GOT, and CATS) of a selected point shows that the tidal amplitude is consistent with the values predicted from tide models to within 4 cm RMS. Even though the lack of data hinders the effort to readily develop a tide model using longer term data (time series span over years), we suggest a method to reconstruction selected tidal constituents using both vertical deformation from InSAR and the knowledge on aliased tidal frequencies from ERS satellites. Finally, we report the comparison results of tidal deformation observed by InSAR and ICESat altimetry.

Evaluating topographic effects on ground deformation: Insights from finite element modeling

NASA Astrophysics Data System (ADS)

Ronchin, Erika; Geyer, Adelina; Marti, Joan

2015-04-01

Ground deformation has been demonstrated to be one of the most common signals of volcanic unrest. Although volcanoes are commonly associated with significant topographic relief, most analytical models assumed the Earth's surface as flat. In the last years, it has been confirmed that this approximation can lead to important misinterpretations of the recorded surface deformation data. Here we perform a systematic and quantitative analysis of how topography may influence ground deformation signals and how these variations correlate with the different topographic parameters characterizing the terrain form (e.g. slope, aspect, curvature, etc.). For this, we bring together the results exposed in previous published papers and complement them with new axisymmetric and 3D Finite Elements (FE) models results. First, we study, in a parametric way, the influence of a volcanic edifice centered above the pressure source axis. Second, we carry out new 3D FE models simulating the real topography of three different volcanic areas representative of topographic scenarios common in volcanic regions: Rabaul caldera (Papua New Guinea) and the volcanic islands of Tenerife and El Hierro (Canary Islands). The calculated differences are then correlated with a series of topographic parameters. The final aim is to investigate the artifacts that might arise from the use of half-space models at volcanic areas considering their diverse topographic features (e.g. collapse caldera structures, prominent central edifices, large landslide scars, etc.). Final conclusions may be also useful for the design of an optimal geodetic monitoring network. This research was partially funded by the European Commission (FP7 Theme: ENV.2011.1.3.3-1; Grant 282759: "VUELCO")and RYC-2012-11024.

Phase unwrapping methods of corner reflector DInSAR monitoring slow ground deformation

NASA Astrophysics Data System (ADS)

Fu, Wenxue; Guo, Xiaofang; Tian, Qingjiu

2007-06-01

Difference interferometric Synthetic aperture radar (DInSAR) has turned out to be a very powerful technique for the measurement of land deformations, but it requires the observed area to be correlated, and coherence degradation will seriously affect the quality of interferogram. Corner reflector DInSAR (CRDInSAR) is a new technique in recently years, which can compensate for the limitation of the classical DInSAR. Due to the stable amplitude and phase performance of the reflector, the interferometric phase difference of the reflector can be used to monitor or measure the small and slowly ground deformation for the cases of large geometrical baseline and large time interval between acquisitions. Phase unwrapping is the process where the absolute phase is reconstructed from its principal value as accurately as possible. It is a key step in the analysis of DInSAR. The classical phase unwrapping methods are either of path following type or of minimum-norm type. However, if the coherence of the two images is very low, the both methods will get error result. In application of CRDInSAR, due to the scattered points, the phase unwrapping of corner reflectors is only dealt with on a sparse grid, so all the reflectors are connected with Delaunay triangulation firstly, which can be used to define neighboring points and elementary cycles. When the monitoring ground deformation is slow, that is unwrapped neighboring-CR phase gradients are supposed to equal their wrapped-phase counterparts, then path-following method and Phase unwrapping using Coefficient of Elevation-Phase-Relation can be used to phase unwrapping. However, in the cases of unwrapped gradients exceeding one-half cycle, minimum cost flow (MCF) method can be used to unwrap the interferogram.

Gravimetric control of active volcanic processes

NASA Astrophysics Data System (ADS)

Saltogianni, Vasso; Stiros, Stathis

2017-04-01

Volcanic activity includes phases of magma chamber inflation and deflation, produced by movement of magma and/or hydrothermal processes. Such effects usually leave their imprint as deformation of the ground surfaces which can be recorded by GNSS and other methods, on one hand, and on the other hand they can be modeled as elastic deformation processes, with deformation produced by volcanic masses of finite dimensions such as spheres, ellipsoids and parallelograms. Such volumes are modeled on the basis of inversion (non-linear, numerical solution) of systems of equations relating the unknown dimensions and location of magma sources with observations, currently mostly GNSS and INSAR data. Inversion techniques depend on the misfit between model predictions and observations, but because systems of equations are highly non-linear, and because adopted models for the geometry of magma sources is simple, non-unique solutions can be derived, constrained by local extrema. Assessment of derived magma models can be provided by independent observations and models, such as micro-seismicity distribution and changes in geophysical parameters. In the simplest case magmatic intrusions can be modeled as spheres with diameters of at least a few tens of meters at a depth of a few kilometers; hence they are expected to have a gravimetric signature in permanent recording stations on the ground surface, while larger intrusions may also have an imprint in sensors in orbit around the earth or along precisely defined air paths. Identification of such gravimetric signals and separation of the "true" signal from the measurement and ambient noise requires fine forward modeling of the wider areas based on realistic simulation of the ambient gravimetric field, and then modeling of its possible distortion because of magmatic anomalies. Such results are useful to remove ambiguities in inverse modeling of ground deformation, and also to detect magmatic anomalies offshore.

Evolution of Deformation Studies on Active Hawaiian Volcanoes

USGS Publications Warehouse

Decker, Robert W.; Okamura, Arnold; Miklius, Asta; Poland, Michael

2008-01-01

Everything responds to pressure, even rocks. Deformation studies involve measuring and interpreting the changes in elevations and horizontal positions of the land surface or sea floor. These studies are variously referred to as geodetic changes or ground-surface deformations and are sometimes indexed under the general heading of geodesy. Deformation studies have been particularly useful on active volcanoes and in active tectonic areas. A great amount of time and energy has been spent on measuring geodetic changes on Kilauea and Mauna Loa Volcanoes in Hawai`i. These changes include the build-up of the surface by the piling up and ponding of lava flows, the changes in the surface caused by erosion, and the uplift, subsidence, and horizontal displacements of the surface caused by internal processes acting beneath the surface. It is these latter changes that are the principal concern of this review. A complete and objective review of deformation studies on active Hawaiian volcanoes would take many volumes. Instead, we attempt to follow the evolution of the most significant observations and interpretations in a roughly chronological way. It is correct to say that this is a subjective review. We have spent years measuring and recording deformation changes on these great volcanoes and more years trying to understand what makes these changes occur. We attempt to make this a balanced as well as a subjective review; the references are also selective rather than exhaustive. Geodetic changes caused by internal geologic processes vary in magnitude from the nearly infinitesimal - one micron or less, to the very large - hundreds of meters. Their apparent causes also are varied and include changes in material properties and composition, atmospheric pressure, tidal stress, thermal stress, subsurface-fluid pressure (including magma pressure, magma intrusion, or magma removal), gravity, and tectonic stress. Deformation is measured in units of strain or displacement. For example, tilt of the ground surface on the rim of Kilauea Caldera is measured in microradians, a strain unit that gives the change in angle from some reference. The direction in which the tilt is measured must be defined - north or south, or some direction normal to the maximum changes. For displacements related to surface faulting, the changes are normally given in linear measures of offset. Changes in the diameter of a caldera can be given in either displacements or strain units. In the later case, the displacement divided by the 'original' diameter gives the strain ratio. Strains are dimensionless numbers; displacements have the dimensions of length. Vectors commonly are used to show the direction and amount of displacements in plan view. Strain results from stress. It can be elastic strain, when the strain is linearly related to stress and is recoverable; it can be viscous strain, where the rate of strain is proportional to the stress and is not recoverable; or it can be plastic strain that is often some complex stress-strain relationship, for example, elastic up to some yield strength and viscous beyond. Volcanic rocks are brittle when cold and under near-surface pressures but plastic to viscous under higher temperature and pressure regimes. It is important in deformation studies to try to define the nature of the strain and the rheology of the rocks being deformed. A good text on rheology is 'The Structure and Rheology of Complex Fluids' by R.G. Larson, 1999. Under changing tensional or compressional stresses, tiny cracks in brittle rocks may open or close, causing a quasielastic strain response. If the stresses exceed the breaking strength of the rock, brittle failure occurs, and the stress-strain relationship breaks down. This is generally the situation with near-field deformation related to earthquakes. Stresses change in complex patterns in both the near- and far-fields of the fracture, and the near-fiel

Multi-temporal InSAR monitoring of landslides in a tropical urban environment: focus on Bukavu (DR Congo)

NASA Astrophysics Data System (ADS)

Nobile, Adriano; Monsieurs, Elise; Dewitte, Olivier; d'Oreyes, Nicolas; Kervyn, Francois

2016-04-01

The western branch of the East African Rift System, in Central Africa, is characterized by the presence of several geohazards: earthquakes, volcanoes, and landslides. Every year, landslides cause fatalities, structural and functional damage to infrastructure and private properties with serious disruptions of the organization of societies and severe impact on the populations. These impacts are particularly important in the city of Bukavu (DR Congo) located within the Rift, on the southern shore of Lake Kivu. Large slow-moving landslides continuously affect highly populated slopes in the city. However little is known about their actual kinematics and the processes at play. Here we use multi-temporal InSAR technique to monitor these ground deformations. Using 50 Cosmo-SkyMed SAR images, acquired between March - October 2015 with a revisiting time of 8 days (ascending and descending orbits), we produce displacement-rate maps and ground deformation time series using the PS technique. Movements with a velocity >5cm/yr are detected, which is consistent with field observations. DGPS measurements, taken at 21 benchmarks in the area during the same period, allow validating the results. Similar ground deformation rates are found for the period 2002-2008 using Envisat ASAR images. Furthermore, comparison with rainfall monitoring data acquire on site should help us to understand the influence of water and the tropical seasonality in the slide mechanisms.

Shifts in the eruptive styles at Stromboli in 2010–2014 revealed by ground-based InSAR data

PubMed Central

Di Traglia, Federico; Battaglia, Maurizio; Nolesini, Teresa; Lagomarsino, Daniela; Casagli, Nicola

2015-01-01

Ground-Based Interferometric Synthetic Aperture Radar (GBInSAR) is an efficient technique for capturing short, subtle episodes of conduit pressurization in open vent volcanoes like Stromboli (Italy), because it can detect very shallow magma storage, which is difficult to identify using other methods. This technique allows the user to choose the optimal radar location for measuring the most significant deformation signal, provides an exceptional geometrical resolution, and allows for continuous monitoring of the deformation. Here, we present and model ground displacements collected at Stromboli by GBInSAR from January 2010 to August 2014. During this period, the volcano experienced several episodes of intense volcanic activity, culminated in the effusive flank eruption of August 2014. Modelling of the deformation allowed us to estimate a source depth of 482 ± 46 m a.s.l. The cumulative volume change was 4.7 ± 2.6 × 105 m3. The strain energy of the source was evaluated 3–5 times higher than the surface energy needed to open the 6–7 August eruptive fissure. The analysis proposed here can help forecast shifts in the eruptive style and especially the onset of flank eruptions at Stromboli and at similar volcanic systems (e.g. Etna, Piton de La Fournaise, Kilauea). PMID:26323251

GB-InSAR monitoring of slope deformations in a mountainous area affected by debris flow events

NASA Astrophysics Data System (ADS)

Frodella, William; Salvatici, Teresa; Pazzi, Veronica; Morelli, Stefano; Fanti, Riccardo

2017-10-01

Diffuse and severe slope instabilities affected the whole Veneto region (north-eastern Italy) between 31 October and 2 November 2010, following a period of heavy and persistent rainfall. In this context, on 4 November 2010 a large detrital mass detached from the cover of the Mt. Rotolon deep-seated gravitational slope deformation (DSGSD), located in the upper Agno River valley, channelizing within the Rotolon Creek riverbed and evolving into a highly mobile debris flow. The latter phenomena damaged many hydraulic works, also threatening bridges, local roads, and the residents of the Maltaure, Turcati, and Parlati villages located along the creek banks and the town of Recoaro Terme. From the beginning of the emergency phase, the civil protection system was activated, involving the National Civil Protection Department, Veneto Region, and local administrations' personnel and technicians, as well as scientific institutions. On 8 December 2010 a local-scale monitoring system, based on a ground-based interferometric synthetic aperture radar (GB-InSAR), was implemented in order to evaluate the slope deformation pattern evolution in correspondence of the debris flow detachment sector, with the final aim of assessing the landslide residual risk and managing the emergency phase. This paper describes the results of a 2-year GB-InSAR monitoring campaign (December 2010-December 2012) and its application for monitoring, mapping, and emergency management activities in order to provide a rapid and easy communication of the results to the involved technicians and civil protection personnel, for a better understanding of the landslide phenomena and the decision-making process in a critical landslide scenario.

Scalable High Performance Image Registration Framework by Unsupervised Deep Feature Representations Learning

PubMed Central

Wu, Guorong; Kim, Minjeong; Wang, Qian; Munsell, Brent C.

2015-01-01

Feature selection is a critical step in deformable image registration. In particular, selecting the most discriminative features that accurately and concisely describe complex morphological patterns in image patches improves correspondence detection, which in turn improves image registration accuracy. Furthermore, since more and more imaging modalities are being invented to better identify morphological changes in medical imaging data,, the development of deformable image registration method that scales well to new image modalities or new image applications with little to no human intervention would have a significant impact on the medical image analysis community. To address these concerns, a learning-based image registration framework is proposed that uses deep learning to discover compact and highly discriminative features upon observed imaging data. Specifically, the proposed feature selection method uses a convolutional stacked auto-encoder to identify intrinsic deep feature representations in image patches. Since deep learning is an unsupervised learning method, no ground truth label knowledge is required. This makes the proposed feature selection method more flexible to new imaging modalities since feature representations can be directly learned from the observed imaging data in a very short amount of time. Using the LONI and ADNI imaging datasets, image registration performance was compared to two existing state-of-the-art deformable image registration methods that use handcrafted features. To demonstrate the scalability of the proposed image registration framework image registration experiments were conducted on 7.0-tesla brain MR images. In all experiments, the results showed the new image registration framework consistently demonstrated more accurate registration results when compared to state-of-the-art. PMID:26552069

Scalable High-Performance Image Registration Framework by Unsupervised Deep Feature Representations Learning.

PubMed

Wu, Guorong; Kim, Minjeong; Wang, Qian; Munsell, Brent C; Shen, Dinggang

2016-07-01

Feature selection is a critical step in deformable image registration. In particular, selecting the most discriminative features that accurately and concisely describe complex morphological patterns in image patches improves correspondence detection, which in turn improves image registration accuracy. Furthermore, since more and more imaging modalities are being invented to better identify morphological changes in medical imaging data, the development of deformable image registration method that scales well to new image modalities or new image applications with little to no human intervention would have a significant impact on the medical image analysis community. To address these concerns, a learning-based image registration framework is proposed that uses deep learning to discover compact and highly discriminative features upon observed imaging data. Specifically, the proposed feature selection method uses a convolutional stacked autoencoder to identify intrinsic deep feature representations in image patches. Since deep learning is an unsupervised learning method, no ground truth label knowledge is required. This makes the proposed feature selection method more flexible to new imaging modalities since feature representations can be directly learned from the observed imaging data in a very short amount of time. Using the LONI and ADNI imaging datasets, image registration performance was compared to two existing state-of-the-art deformable image registration methods that use handcrafted features. To demonstrate the scalability of the proposed image registration framework, image registration experiments were conducted on 7.0-T brain MR images. In all experiments, the results showed that the new image registration framework consistently demonstrated more accurate registration results when compared to state of the art.

Ground surface deformation patterns, magma supply, and magma storage at Okmok volcano, Alaska, from InSAR analysis: 2. Coeruptive deflation, July-August 2008

USGS Publications Warehouse

Lu, Zhong; Dzurisin, Daniel

2010-01-01

A hydrovolcanic eruption near Cone D on the floor of Okmok caldera, Alaska, began on 12 July 2008 and continued until late August 2008. The eruption was preceded by inflation of a magma reservoir located beneath the center of the caldera and ∼3 km below sea level (bsl), which began immediately after Okmok's previous eruption in 1997. In this paper we use data from several radar satellites and advanced interferometric synthetic aperture radar (InSAR) techniques to produce a suite of 2008 coeruption deformation maps. Most of the surface deformation that occurred during the eruption is explained by deflation of a Mogi-type source located beneath the center of the caldera and 2–3 km bsl, i.e., essentially the same source that inflated prior to the eruption. During the eruption the reservoir deflated at a rate that decreased exponentially with time with a 1/e time constant of ∼13 days. We envision a sponge-like network of interconnected fractures and melt bodies that in aggregate constitute a complex magma storage zone beneath Okmok caldera. The rate at which the reservoir deflates during an eruption may be controlled by the diminishing pressure difference between the reservoir and surface. A similar mechanism might explain the tendency for reservoir inflation to slow as an eruption approaches until the pressure difference between a deep magma production zone and the reservoir is great enough to drive an intrusion or eruption along the caldera ring-fracture system.

A comprehensive approach to monitoring volcano deformation as a window on the eruption cycle

USGS Publications Warehouse

Dzurisin, D.

2003-01-01

Since the 1980 eruption of Mount St. Helens, volcanologists have made considerable progress toward predicting eruptions on the basis of precursors that typically start a few days to several months in advance. Although accurate eruption prediction is by no means routine, it may now be possible in some cases to extend the effective warning period by anticipating the onset of short-term precursors. Three promising indicators of deep magmatic processes are (1) deep, long-period earthquakes and tremor that indicate the ascent of magma through the crust, (2) magmatic CO2 emission rate as a proxy for magma supply rate, and (3) relatively broad, generally aseismic surface uplift caused by magmatic intrusions. In the latter case it is essential to sample the deformation field thoroughly in both time and space to adequately constrain source models. Until recently, this has been nearly impossible because high-precision sensors could not be deployed in sufficient numbers, nor could extensive geodetic surveys be conducted often enough. Advances in instrumentation, interferometric synthetic aperture radar (InSAR), and telecommunications are helping to overcome these limitations. As a result, comprehensive geodetic monitoring of selected volcanoes is now feasible. A combination of InSAR, large-aperture GPS surveys, microgravity surveys, and dense arrays of continuous GPS stations, strain meters, and tiltmeters can reveal both spatial and temporal patterns of ground deformation throughout the eruption cycle. Improved geodetic monitoring of many of the world's volcanoes would be a major stride toward better understanding of magmatic processes and longer-term eruption forecasts.

Practical guidelines to select and scale earthquake records for nonlinear response history analysis of structures

USGS Publications Warehouse

Kalkan, Erol; Chopra, Anil K.

2010-01-01

Earthquake engineering practice is increasingly using nonlinear response history analysis (RHA) to demonstrate performance of structures. This rigorous method of analysis requires selection and scaling of ground motions appropriate to design hazard levels. Presented herein is a modal-pushover-based scaling (MPS) method to scale ground motions for use in nonlinear RHA of buildings and bridges. In the MPS method, the ground motions are scaled to match (to a specified tolerance) a target value of the inelastic deformation of the first-'mode' inelastic single-degree-of-freedom (SDF) system whose properties are determined by first-'mode' pushover analysis. Appropriate for first-?mode? dominated structures, this approach is extended for structures with significant contributions of higher modes by considering elastic deformation of second-'mode' SDF system in selecting a subset of the scaled ground motions. Based on results presented for two bridges, covering single- and multi-span 'ordinary standard' bridge types, and six buildings, covering low-, mid-, and tall building types in California, the accuracy and efficiency of the MPS procedure are established and its superiority over the ASCE/SEI 7-05 scaling procedure is demonstrated.

Liquefaction, flow, and associated ground failure

USGS Publications Warehouse

Youd, T. Leslie

1973-01-01

Ambiguities in the use of the term liquefaction and in defining the relation between liquefaction and ground failure have led to encumbered communication between workers in various fields and between specialists in the same field, and the possibility that evaluations of liquefaction potential could be misinterpreted or misapplied. Explicit definitions of liquefaction and related concepts are proposed herein. These definitions, based on observed laboratory behavior, are then used to clarify the relation between liquefaction and ground failure. Soil liquefaction is defined as the transformation of a granular material from a solid into a liquefied state as a consequence of increased pore-water pressures. This definition avoids confusion between liquefaction and possible flow-failure conditions after liquefaction. Flow-failure conditions are divided into two types: (1) unlimited flow if pore-pressure reductions caused by dilatancy during flow deformation are not sufficient to solidify the material and thus arrest flow, and (2) limited flow if they are sufficient to solidify the material after a finite deformation. After liquefaction in the field, unlimited flow commonly leads to flow landslides, whereas limited flow leads at most to lateral-spreading landslides. Quick-condition failures such as loss of bearing capacity form a third type of ground failure associated with liquefaction.

Parameter Calibration and Numerical Analysis of Twin Shallow Tunnels

NASA Astrophysics Data System (ADS)

Paternesi, Alessandra; Schweiger, Helmut F.; Scarpelli, Giuseppe

2017-05-01

Prediction of displacements and lining stresses in underground openings represents a challenging task. The main reason is primarily related to the complexity of this ground-structure interaction problem and secondly to the difficulties in obtaining a reliable geotechnical characterisation of the soil or the rock. In any case, especially when class A predictions fail in forecasting the system behaviour, performing class B or C predictions, which rely on a higher level of knowledge of the surrounding ground, can represent a useful resource for identifying and reducing model deficiencies. The case study presented in this paper deals with the construction works of twin-tube shallow tunnels excavated in a stiff and fine-grained deposit. The work initially focuses on the ground parameter calibration against experimental data, which together with the choice of an appropriate constitutive model plays a major role in the assessment of tunnelling-induced deformations. Since two-dimensional analyses imply initial assumptions to take into account the effect of the 3D excavation, three-dimensional finite element analyses were preferred. Comparisons between monitoring data and results of numerical simulations are provided. The available field data include displacements and deformation measurements regarding both the ground and tunnel lining.

Neighborhood binary speckle pattern for deformation measurements insensitive to local illumination variation by digital image correlation.

PubMed

Zhao, Jian; Yang, Ping; Zhao, Yue

2017-06-01

Speckle pattern-based characteristics of digital image correlation (DIC) restrict its application in engineering fields and nonlaboratory environments, since serious decorrelation effect occurs due to localized sudden illumination variation. A simple and efficient speckle pattern adjusting and optimizing approach presented in this paper is aimed at providing a novel speckle pattern robust enough to resist local illumination variation. The new speckle pattern, called neighborhood binary speckle pattern, derived from original speckle pattern, is obtained by means of thresholding the pixels of a neighborhood at its central pixel value and considering the result as a binary number. The efficiency of the proposed speckle pattern is evaluated in six experimental scenarios. Experiment results indicate that the DIC measurements based on neighborhood binary speckle pattern are able to provide reliable and accurate results, even though local brightness and contrast of the deformed images have been seriously changed. It is expected that the new speckle pattern will have more potential value in engineering applications.

Thermal input control and enhancement for laser based residual stress measurements using liquid temperature indicating coatings

DOEpatents

Pechersky, M.J.

1999-07-06

An improved method for measuring residual stress in a material is disclosed comprising the steps of applying a spot of temperature indicating coating to the surface to be studied, establishing a speckle pattern surrounds the spot of coating with a first laser then heating the spot of coating with a far infrared laser until the surface plastically deforms. Comparing the speckle patterns before and after deformation by subtracting one pattern from the other will produce a fringe pattern that serves as a visual and quantitative indication of the degree to which the plasticized surface responded to the stress during heating and enables calculation of the stress. 3 figs.

Thermal input control and enhancement for laser based residual stress measurements using liquid temperature indicating coatings

DOEpatents

Pechersky, Martin J.

1999-01-01

An improved method for measuring residual stress in a material comprising the steps of applying a spot of temperature indicating coating to the surface to be studied, establishing a speckle pattern surrounds the spot of coating with a first laser then heating the spot of coating with a far infrared laser until the surface plastically deforms. Comparing the speckle patterns before and after deformation by subtracting one pattern from the other will produce a fringe pattern that serves as a visual and quantitative indication of the degree to which the plasticized surface responded to the stress during heating and enables calculation of the stress.

Topographic Response to the Yakutat Block Collision

NASA Technical Reports Server (NTRS)

Stock, Joann M.

2000-01-01

The principal objective of this grant and this research were to investigate the topographic development of an active glaciated orogenic belt in southern Alaska as that development relates to patterns of erosion and crustal deformation. A specific objective of the research was to investigate feedbacks between mountain building, orographic affects on climate, and patterns of exhumation and rock uplift. To that end, an orogen-scale analysis of topography was conducted with the aid of digital elevation models, magnitudes and patterns of crustal deformation were compiled from existing literature, present and past climate patterns were constrained using the modern and past distribution of glaciers, and styles, magnitudes, and extent of erosion were constrained with observations from the 1998 field season.

Study on Elastic Helical TDR Sensing Cable for Distributed Deformation Detection

PubMed Central

Tong, Renyuan; Li, Ming; Li, Qing

2012-01-01

In order to detect distributed ground surface deformation, an elastic helical structure Time Domain Reflectometry (TDR) sensing cable is shown in this paper. This special sensing cable consists of three parts: a silicone rubber rope in the center; a couple of parallel wires coiling around the rope; a silicone rubber pipe covering the sensing cable. By analyzing the relationship between the impedance and the structure of the sensing cable, the impedance model shows that the sensing cable impedance will increase when the cable is stretched. This specific characteristic is verified in the cable stretching experiment which is the base of TDR sensing technology. The TDR experiment shows that a positive reflected signal is created at the stretching deformation point on the sensing cable. The results show that the deformation section length and the stretching elongation will both affect the amplitude of the reflected signal. Finally, the deformation locating experiments show that the sensing cable can accurately detect the deformation point position on the sensing cable. PMID:23012560

Ground deformation associated with the precursory unrest and early phases of the January 2006 eruption of Augustine volcano, Alaska

USGS Publications Warehouse

Cervelli, P.F.; Fournier, T.; Freymueller, Jeffrey T.; Power, J.A.

2006-01-01

On January 11, 2006 Augustine Volcano erupted after nearly 20 years of quiescence. Global Positioning System (GPS) instrumentation at Augustine, consisting of six continuously recording, telemetered receivers, measured clear precursory deformation consistent with a source of inflation or pressurization beneath the volcano's summit at a depth of around sea level. Deformation began in early summer 2005, and was preceded by a subtle, but distinct, increase in seismicity, which began in May 2005. After remaining more or less constant, deformation rates accelerated on at least three stations beginning in late November 2005. After this date, GPS data suggest the upward propagation of a small dike into the edifice, which, based on the style of deformation and high levels of gas emission, appears to have ascended to shallow levels by mid-December 2005, about four weeks before the eruption began.

Equilibrium stability of a cylindrical body subject to the internal structure of the material and inelastic behaviour of the completely compressed matrix

NASA Astrophysics Data System (ADS)

Gotsev, D. V.; Perunov, N. S.; Sviridova, E. N.

2018-03-01

The mathematical model describing the stress-strain state of a cylindrical body under the uniform radial compression effect is constructed. The model of the material is the porous medium model. The compressed skeleton of the porous medium possesses hardening elastic-plastic properties. Deforming of the porous medium under the specified compressive loads is divided into two stages: elastic deforming of the porous medium and further elastic-plastic deforming of the material with completely compressed matrix. The analytical relations that define the fields of stress and displacement at each stage of the deforming are obtained. The influence of the porosity and other physical, mechanical and geometric parameters of the construction on the size of the plastic zone is evaluated. The question of the ground state equilibrium instability is investigated within the framework of the three-dimensional linearized relationships of the stability theory of deformed bodies.

Microdeformation and subcritical cracking in chalk

NASA Astrophysics Data System (ADS)

Bergsaker, Anne; Dysthe, Dag Kristian

2016-04-01

Deformation processes in chalks, both in relation to changing pore fluids and stress conditions has been of great interest as chalk is an important reservoir rock for both hydrocarbons and ground water. Lately it has also gained interest as a potential reservoir rock for captured CO2. Chalks are composed of large amounts of biogenic calcite grains, the skeletal debris of marine microorganisms. Its deformation is highly time and stress dependent, and governed by a transition from distributed to localized deformation at the onset of yield, affected by mechanisms such as subcritical crack growth and pore collapse. We present a microdeformation rig which makes use of thermal expansion as a means of subjecting small samples to strictly controlled tensile stresses. High resolution imaging provides resolutions down to 0.5 micrometers, enabling study of pore scale processes during slow deformation. Examples of localized and distributed deformation are presented.

Synchronized diffusive-wave spectroscopy: Principle and application to sound propagation in aqueous foams.

PubMed

Crassous, Jérôme; Chasle, Patrick; Pierre, Juliette; Saint-Jalmes, Arnaud; Dollet, Benjamin

2016-03-01

We present an experimental method to measure oscillatory strains in turbid material. The material is illuminated with a laser, and the speckle patterns are recorded. The analysis of the deformations of the optical path length shows that the speckle patterns are modulated at the strain frequency. By recording those patterns synchronously with the strain source, we are able to measure the amplitude and the phase of the strain. This method is tested in the specific case of an aqueous foam where an acoustic wave propagates. The effects of material internal dynamics and heterogeneous deformations are also discussed.

Synchronized diffusive-wave spectroscopy: Principle and application to sound propagation in aqueous foams

NASA Astrophysics Data System (ADS)

Crassous, Jérôme; Chasle, Patrick; Pierre, Juliette; Saint-Jalmes, Arnaud; Dollet, Benjamin

2016-03-01

We present an experimental method to measure oscillatory strains in turbid material. The material is illuminated with a laser, and the speckle patterns are recorded. The analysis of the deformations of the optical path length shows that the speckle patterns are modulated at the strain frequency. By recording those patterns synchronously with the strain source, we are able to measure the amplitude and the phase of the strain. This method is tested in the specific case of an aqueous foam where an acoustic wave propagates. The effects of material internal dynamics and heterogeneous deformations are also discussed.

Characterization of Ground Displacement Sources from Variational Bayesian Independent Component Analysis of Space Geodetic Time Series

NASA Astrophysics Data System (ADS)

Gualandi, Adriano; Serpelloni, Enrico; Elina Belardinelli, Maria; Bonafede, Maurizio; Pezzo, Giuseppe; Tolomei, Cristiano

2015-04-01

A critical point in the analysis of ground displacement time series, as those measured by modern space geodetic techniques (primarly continuous GPS/GNSS and InSAR) is the development of data driven methods that allow to discern and characterize the different sources that generate the observed displacements. A widely used multivariate statistical technique is the Principal Component Analysis (PCA), which allows to reduce the dimensionality of the data space maintaining most of the variance of the dataset explained. It reproduces the original data using a limited number of Principal Components, but it also shows some deficiencies, since PCA does not perform well in finding the solution to the so-called Blind Source Separation (BSS) problem. The recovering and separation of the different sources that generate the observed ground deformation is a fundamental task in order to provide a physical meaning to the possible different sources. PCA fails in the BSS problem since it looks for a new Euclidean space where the projected data are uncorrelated. Usually, the uncorrelation condition is not strong enough and it has been proven that the BSS problem can be tackled imposing on the components to be independent. The Independent Component Analysis (ICA) is, in fact, another popular technique adopted to approach this problem, and it can be used in all those fields where PCA is also applied. An ICA approach enables us to explain the displacement time series imposing a fewer number of constraints on the model, and to reveal anomalies in the data such as transient deformation signals. However, the independence condition is not easy to impose, and it is often necessary to introduce some approximations. To work around this problem, we use a variational bayesian ICA (vbICA) method, which models the probability density function (pdf) of each source signal using a mix of Gaussian distributions. This technique allows for more flexibility in the description of the pdf of the sources, giving a more reliable estimate of them. Here we introduce the vbICA technique and present its application on synthetic data that simulate a GPS network recording ground deformation in a tectonically active region, with synthetic time-series containing interseismic, coseismic, and postseismic deformation, plus seasonal deformation, and white and coloured noise. We study the ability of the algorithm to recover the original (known) sources of deformation, and then apply it to a real scenario: the Emilia seismic sequence (2012, northern Italy), which is an example of seismic sequence occurred in a slowly converging tectonic setting, characterized by several local to regional anthropogenic or natural sources of deformation, mainly subsidence due to fluid withdrawal and sediments compaction. We apply both PCA and vbICA to displacement time-series recorded by continuous GPS and InSAR (Pezzo et al., EGU2015-8950).

Ground deformation associated with the 2008 Sichuan Earthquake in China, estimated using a SAR offset-tracking method

NASA Astrophysics Data System (ADS)

Kobayashi, T.; Takada, Y.; Furuya, M.; Murakami, M.

2008-12-01

Introduction: A catastrophic earthquake struck China"fs Sichuan area on May 12, 2008, with the moment magnitude of 7.9 (USGS). The hypocenter and their aftershocks are distributed along the western edge of the Sichuan Basin, suggesting that this seismic event occurred at the Longmeng Shan fault zone which is constituted of major three active faults (Wenchuan-Maowen, Beichuan, and Pengguan faults). However, it is unclear whether these faults were directly involved in the mainshock rupture. An interferometry SAR (InSAR) analysis generally has a merit that we can detect ground deformation in a vast region with high precision, however, for the Sichuan event, the surface deformation near the fault zone has not been satisfactorily detected from the InSAR analyses due to a low coherency. An offset-tracking method is less precise but more robust for detecting large ground deformation than the interferometric approach. Our purpose is to detect the detail ground deformation immediately near the faults involved in the Sichuan event with applying the offset-tracking method. Analysis Method: We analyzed ALOS/PALSAR images, which have been taken from Path 471 to 476 of ascending track, acquired before and after the mainshock. We processed SAR data from the level-1.0 product, using a software package from Gamma Remote Sensing. For offset-tracking analysis we adopt intensity tracking method which is performed by cross-correlating samples of backscatter intensity of a master SAR image with samples from the corresponding search area of a slave image in order to estimate range and azimuth offset fields. We reduce stereoscopic effects that produce apparent offsets, using SRTM3 DEM data. Results: We have successfully obtained the surface deformation in range (radar look direction) component, while in azimuth (flight direction) no significant deformation can be detected in some orbits due to "gazimuth streaks"h that are errors caused by ionospheric effects. Some concluding remarks are as follows: On the Beichuan F. and its northeastward extension, a clear boundary of a motion toward and away from the satellite can be recognized just along the fault, which is almost consistent with a right-lateral fault motion. On the other hand, in the southwestern region from the Beichuan city where the three major faults are running almost parallel, two boundaries of motions can be recognized; On the Beichuan F. there are a clear displacement boundary in range component, while on the Pengguan F. a boundary can be identified in azimuth component rather than in range, suggesting that the seismic ruptures proceeded with different fault motions at each fault. For the Wenchuan-Maowen F., no significant displacement boundary can be recognized. Acknowledgments: PALSAR data are provided from Earthquake Working Group and PIXEL (PALSAR Interferometry Consortium to Study our Evolving Land surface) under a cooperative research contract with JAXA. The ownership of PALSAR data belongs to METI (Ministry of Economy, Trade and Industry) and JAXA.

Monitoring of Land Deformation Due to Oil Production by InSAR Time Series Analysis Using PALSAR Data in Bolivarian Republic of Venezuela

NASA Astrophysics Data System (ADS)

Deguchi, Tomonori; Narita, Tatsuhiko

2015-05-01

The target area of this study is the Maracaibo sedimentary basin located in the western part of Bolivarian Republic of Venezuela. The full-scale exploration and development for oil resources in Venezuela which was the greatest oil-producing country in South America had begun at the Maracaibo sedimentary basin in the 1910s, and it was a center of the oil product in Venezuela until the 1980s. But, in most of oil fields in the Maracaibo sedimentary basin, there is concern over the drain on recoverable reserves due to deterioration, and the production amount of petroleum in Venezuela has been diminishing these days. Leveling and GPS surveying were carried out in the past, and they revealed that the large-scale subsidence phenomenon of which cumulative subsidence amount was approximately 5 meter had occurred. The authors applied the vertical displacement measurement by InSAR time series analysis using PALSAR data obtained in the Fine-beam and ScanSAR observation mode. As a result, it could be confirmed clear ground deformation in the surrounding of three oil fields (Tia Juana, Lagunillas and Bachaquero) and easily recognized that the areas of phase anomalies detected by this analysis had expanded and the number of interference fringes had increased over time. The annual velocity of vertical ground surface displacement measured by InSAR time series analysis was -51 mm per year, -103 mm per year and -58 mm per year in Tia Juana, Lagunillas and Bachaquero oil field respectively. The tendency that an earth surface shifted towards the center of phase anomalies was detected from the result of the horizontal ground change measurement. It was interpreted from Google Earth and Landsat images that oil-related facilities (mainly bowling stations) were built intensively over the areas where phase anomalies were detected. Therefore, it was inferred that there was a high association between the operation activity of the oil field and ground deformation. In addition, the deterioration is remarkable in the oil fields of the Maracaibo basin and oil production volume has been declining, on the other hand the spatial volume of the ground surface deformation also showed a clear decreasing trend.

Deformations and Rotational Ground Motions Inferred from Downhole Vertical Array Observations

NASA Astrophysics Data System (ADS)

Graizer, V.

2017-12-01

Only few direct reliable measurements of rotational component of strong earthquake ground motions are obtained so far. In the meantime, high quality data recorded at downhole vertical arrays during a number of earthquakes provide an opportunity to calculate deformations based on the differences in ground motions recorded simultaneously at different depths. More than twenty high resolution strong motion downhole vertical arrays were installed in California with primary goal to study site response of different geologic structures to strong motion. Deformation or simple shear strain with the rate γ is the combination of pure shear strain with the rate γ/2 and rotation with the rate of α=γ/2. Deformations and rotations were inferred from downhole array records of the Mw 6.0 Parkfield 2004, the Mw 7.2 Sierra El Mayor (Mexico) 2010, the Mw 6.5 Ferndale area in N. California 2010 and the two smaller earthquakes in California. Highest amplitude of rotation of 0.60E-03 rad was observed at the Eureka array corresponding to ground velocity of 35 cm/s, and highest rotation rate of 0.55E-02 rad/s associated with the S-wave was observed at a close epicentral distance of 4.3 km from the ML 4.2 event in Southern California at the La Cienega array. Large magnitude Sierra El Mayor earthquake produced long duration rotational motions of up to 1.5E-04 rad and 2.05E-03 rad/s associated with shear and surface waves at the El Centro array at closest fault distance of 33.4km. Rotational motions of such levels, especially tilting can have significant effect on structures. High dynamic range well synchronized and properly oriented instrumentation is necessary for reliable calculation of rotations from vertical array data. Data from the dense Treasure Island array near San Francisco demonstrate consistent change of shape of rotational motion with depth and material. In the frequency range of 1-15 Hz Fourier amplitude spectrum of vertical ground velocity is similar to the scaled tilt spectrum. Amplitudes of rotations at the site depend upon the size of the base and usually decrease with depth. They are also amplified by soft material. Earthquake data used in this study were downloaded from the Center for Engineering Strong Motion Data at http://www.strongmotioncenter.org/.

Monitoring and modeling of sinkhole-related subsidence in west-central Florida mapped from InSAR and surface observations

NASA Astrophysics Data System (ADS)

Kiflu, H.; Oliver-Cabrera, T.; Robinson, T.; Wdowinski, S.; Kruse, S.

2017-12-01

Sinkholes in Florida cause millions of dollars in damage to infrastructure each year. Methods of early detection of sinkhole-related subsidence are clearly desirable. We have completed two years of monitoring of selected sinkhole-prone areas in west central Florida with XXX data and analysis with XXX algorithms. Filters for selecting targets with high signal-to-noise ratio and subsidence over this time window (XX-2015-XX-2017) are being used to select sites for ground study. A subset of the buildings with InSAR-detected subsidence indicated show clear structural indications of subsidence in the form of cracks in walls and roofs. Comsol Multiphysics models have been developed to describe subsidence at the rates identified from the InSAR analysis (a few mm/year) and on spatial scales observed from surface observations, including structural deformation of buildings and ground penetrating radar images of subsurface deformation (length scales of meters to tens of meters). These models assume cylindrical symmetry and deformation of elastic and poroelastic layers over a growing sphering void.

Tertiary thrust systems and fluid flow beneath the Beaufort coastal plain (1002 area), Arctic National Wildlife Refuge, Alaska, U.S.A.

USGS Publications Warehouse

Potter, Christopher J.; Grow, John A.; Perry, William J.; Moore, Thomas E.; O'Sullivan, Paul B.; Phillips, Jeffrey D.; Saltus, Richard W.

2004-01-01

In the eastern part of the 1002 area, a northward-younging pattern of thin-skinned deformation is apparent. Converging patterns of Paleocene reflectors on the north flank of the Sabbath syncline indicate that the Aichilik high and the Sabbath syncline formed as a passive-roof duplex and piggyback basin, respectively, just behind the Paleocene deformation front. During the Eocene and possibly the Oligocene, thin-skinned thrusting advanced northward over the present location of the Niguanak high. A passive-roof duplex occupied the frontal part of this system. The Kingak and Hue shales exposed above the Niguanak high were transported into their present structural position during the Eocene to Oligocene motion on the long thrust ramps above the present south flank of the Niguanak high. Broad, basement-cored subsurface domes (Niguanak high and Aurora dome) formed near the deformation front in the Oligocene, deforming the overlying thin-skinned structures and feeding a new increment of displacement into thin-skinned structures directly to the north. Deformation continued through the Miocene above a detachment in the basement. Offshore seismicity and Holocene shortening documented by previous workers may indicate that contractional deformation continues to the present day.

Dynamic deformation inspection of a human arm by using a line-scan imaging system

NASA Astrophysics Data System (ADS)

Hu, Eryi

2009-11-01

A line-scan imaging system is used in the dynamic deformation measurement of a human arm when the muscle is contracting and relaxing. The measurement principle is based on the projection grating profilometry, and the measuring system is consisted of a line-scan CCD camera, a projector, optical lens and a personal computer. The detected human arm is put upon a reference plane, and a sinusoidal grating is projected onto the object surface and reference plane at an incidence angle, respectively. The deformed fringe pattern in the same line of the dynamic detected arm is captured by the line-scan CCD camera with free trigger model, and the deformed fringe pattern is recorded in the personal computer for processing. A fast Fourier transform combining with a filtering and spectrum shifting method is used to extract the phase information caused by the profile of the detected object. Thus, the object surface profile can be obtained following the geometric relationship between the fringe deformation and the object surface height. Furthermore, the deformation procedure can be obtained line by line. Some experimental results are presented to prove the feasibility of the inspection system.

A New CT Reconstruction Technique Using Adaptive Deformation Recovery and Intensity Correction (ADRIC)

PubMed Central

Zhang, You; Ma, Jianhua; Iyengar, Puneeth; Zhong, Yuncheng; Wang, Jing

2017-01-01

Purpose Sequential same-patient CT images may involve deformation-induced and non-deformation-induced voxel intensity changes. An adaptive deformation recovery and intensity correction (ADRIC) technique was developed to improve the CT reconstruction accuracy, and to separate deformation from non-deformation-induced voxel intensity changes between sequential CT images. Materials and Methods ADRIC views the new CT volume as a deformation of a prior high-quality CT volume, but with additional non-deformation-induced voxel intensity changes. ADRIC first applies the 2D-3D deformation technique to recover the deformation field between the prior CT volume and the new, to-be-reconstructed CT volume. Using the deformation-recovered new CT volume, ADRIC further corrects the non-deformation-induced voxel intensity changes with an updated algebraic reconstruction technique (‘ART-dTV’). The resulting intensity-corrected new CT volume is subsequently fed back into the 2D-3D deformation process to further correct the residual deformation errors, which forms an iterative loop. By ADRIC, the deformation field and the non-deformation voxel intensity corrections are optimized separately and alternately to reconstruct the final CT. CT myocardial perfusion imaging scenarios were employed to evaluate the efficacy of ADRIC, using both simulated data of the extended-cardiac-torso (XCAT) digital phantom and experimentally acquired porcine data. The reconstruction accuracy of the ADRIC technique was compared to the technique using ART-dTV alone, and to the technique using 2D-3D deformation alone. The relative error metric and the universal quality index metric are calculated between the images for quantitative analysis. The relative error is defined as the square root of the sum of squared voxel intensity differences between the reconstructed volume and the ‘ground-truth’ volume, normalized by the square root of the sum of squared ‘ground-truth’ voxel intensities. In addition to the XCAT and porcine studies, a physical lung phantom measurement study was also conducted. Water-filled balloons with various shapes/volumes and concentrations of iodinated contrasts were put inside the phantom to simulate both deformations and non-deformation-induced intensity changes for ADRIC reconstruction. The ADRIC-solved deformations and intensity changes from limited-view projections were compared to those of the ‘gold-standard’ volumes reconstructed from fully-sampled projections. Results For the XCAT simulation study, the relative errors of the reconstructed CT volume by the 2D-3D deformation technique, the ART-dTV technique and the ADRIC technique were 14.64%, 19.21% and 11.90% respectively, by using 20 projections for reconstruction. Using 60 projections for reconstruction reduced the relative errors to 12.33%, 11.04% and 7.92% for the three techniques, respectively. For the porcine study, the corresponding results were 13.61%, 8.78%, 6.80% by using 20 projections; and 12.14%, 6.91% and 5.29% by using 60 projections. The ADRIC technique also demonstrated robustness to varying projection exposure levels. For the physical phantom study, the average DICE coefficient between the initial prior balloon volume and the new ‘gold-standard’ balloon volumes was 0.460. ADRIC reconstruction by 21 projections increased the average DICE coefficient to 0.954. Conclusion The ADRIC technique outperformed both the 2D-3D deformation technique and the ART-dTV technique in reconstruction accuracy. The alternately solved deformation field and non-deformation voxel intensity corrections can benefit multiple clinical applications, including tumor tracking, radiotherapy dose accumulation and treatment outcome analysis. PMID:28380247

Uncovering the deformation mechanisms of origami metamaterials by introducing generic degree-four vertices.

PubMed

Fang, Hongbin; Li, Suyi; Ji, Huimin; Wang, K W

2016-10-01

Origami-based design holds promise for developing new mechanical metamaterials whose overall kinematic and mechanical properties can be programmed using purely geometric criteria. In this article, we demonstrate that the deformation of a generic degree-four vertex (4-vertex) origami cell is a combination of contracting, shearing, bending, and facet-binding. The last three deformation mechanisms are missing in the current rigid-origami metamaterial investigations, which focus mainly on conventional Miura-ori patterns. We show that these mechanisms provide the 4-vertex origami sheets and blocks with new deformation patterns as well as extraordinary kinematical and mechanical properties, including self-locking, tridirectional negative Poisson's ratios, flipping of stiffness profiles, and emerging shearing stiffness. This study reveals that the 4-vertex cells offer a better platform and greater design space for developing origami-based mechanical metamaterials than the conventional Miura-ori cell.

Uncovering the deformation mechanisms of origami metamaterials by introducing generic degree-four vertices

NASA Astrophysics Data System (ADS)

Fang, Hongbin; Li, Suyi; Ji, Huimin; Wang, K. W.

2016-10-01

Origami-based design holds promise for developing new mechanical metamaterials whose overall kinematic and mechanical properties can be programmed using purely geometric criteria. In this article, we demonstrate that the deformation of a generic degree-four vertex (4-vertex) origami cell is a combination of contracting, shearing, bending, and facet-binding. The last three deformation mechanisms are missing in the current rigid-origami metamaterial investigations, which focus mainly on conventional Miura-ori patterns. We show that these mechanisms provide the 4-vertex origami sheets and blocks with new deformation patterns as well as extraordinary kinematical and mechanical properties, including self-locking, tridirectional negative Poisson's ratios, flipping of stiffness profiles, and emerging shearing stiffness. This study reveals that the 4-vertex cells offer a better platform and greater design space for developing origami-based mechanical metamaterials than the conventional Miura-ori cell.

Investigating Different Patterns of Slab Deformation in the Lower Mantle

NASA Astrophysics Data System (ADS)

Zhang, J.; McNamara, A. K.

2017-12-01

The geometry of slabs within the upper mantle have been relatively well-imaged by tomography and regional seismic studies; however, the style of slab deformation in the lower mantle remains poorly understood. Although tomography models reveal that the lower mantle beneath paleo-subduction regions are faster-than-average, the resolution is not high enough to resolve how slabs are actually deforming there. Slabs have long been hypothesized as viscous, tabular sheets that subduct at the surface, descend through the mantle, and impinge on the core-mantle boundary (CMB). Geodynamical studies have shown a wide range of possible deformational behaviors, ranging from stiff, buckling slabs to more-ductile masses of accumulating slab material undergoing pure shear. Of particular interest is how rheology and 3D spherical geometry control the shape and deformational style of slabs as they descend deeper into the mantle. We performed high resolution 3D spherical calculations to explore slab deformation in deep mantle as a function of slab strength. In our model, kinematic velocity boundary conditions are imposed on the surface to simulate a moving plate which guides the formation of a subducting slab. In addition, a viscosity jump at the transition zone is applied. We find that although a slab subducts as a large tabular sheet from the surface, it doesn't always maintain such geometry. Instead, it typically breaks apart into a few smaller and narrower sheets which can even turn into cylindrical-shaped downwelling after subducting into deep mantle. Since seismic anisotropy is hypothesized to originate from crystal preferred orientation (CPO) in a slab when it impinges on the CMB and is predicted with significant help of time-dependent deformation information from the geodynamic models, our findings on lower mantle slab deformation patterns may enhance the understanding towards the cause of characteristic patterns of predicted seismic anisotropy.

Kinematic primitives for walking and trotting gaits of a quadruped robot with compliant legs.

PubMed

Spröwitz, Alexander T; Ajallooeian, Mostafa; Tuleu, Alexandre; Ijspeert, Auke Jan

2014-01-01

In this work we research the role of body dynamics in the complexity of kinematic patterns in a quadruped robot with compliant legs. Two gait patterns, lateral sequence walk and trot, along with leg length control patterns of different complexity were implemented in a modular, feed-forward locomotion controller. The controller was tested on a small, quadruped robot with compliant, segmented leg design, and led to self-stable and self-stabilizing robot locomotion. In-air stepping and on-ground locomotion leg kinematics were recorded, and the number and shapes of motion primitives accounting for 95% of the variance of kinematic leg data were extracted. This revealed that kinematic patterns resulting from feed-forward control had a lower complexity (in-air stepping, 2-3 primitives) than kinematic patterns from on-ground locomotion (νm4 primitives), although both experiments applied identical motor patterns. The complexity of on-ground kinematic patterns had increased, through ground contact and mechanical entrainment. The complexity of observed kinematic on-ground data matches those reported from level-ground locomotion data of legged animals. Results indicate that a very low complexity of modular, rhythmic, feed-forward motor control is sufficient for level-ground locomotion in combination with passive compliant legged hardware.

Kinematic primitives for walking and trotting gaits of a quadruped robot with compliant legs

PubMed Central

Spröwitz, Alexander T.; Ajallooeian, Mostafa; Tuleu, Alexandre; Ijspeert, Auke Jan

2014-01-01

In this work we research the role of body dynamics in the complexity of kinematic patterns in a quadruped robot with compliant legs. Two gait patterns, lateral sequence walk and trot, along with leg length control patterns of different complexity were implemented in a modular, feed-forward locomotion controller. The controller was tested on a small, quadruped robot with compliant, segmented leg design, and led to self-stable and self-stabilizing robot locomotion. In-air stepping and on-ground locomotion leg kinematics were recorded, and the number and shapes of motion primitives accounting for 95% of the variance of kinematic leg data were extracted. This revealed that kinematic patterns resulting from feed-forward control had a lower complexity (in-air stepping, 2–3 primitives) than kinematic patterns from on-ground locomotion (νm4 primitives), although both experiments applied identical motor patterns. The complexity of on-ground kinematic patterns had increased, through ground contact and mechanical entrainment. The complexity of observed kinematic on-ground data matches those reported from level-ground locomotion data of legged animals. Results indicate that a very low complexity of modular, rhythmic, feed-forward motor control is sufficient for level-ground locomotion in combination with passive compliant legged hardware. PMID:24639645

Ultrasound Imaging of Muscle Contraction of the Tibialis Anterior in Patients with Facioscapulohumeral Dystrophy.

PubMed

Gijsbertse, Kaj; Goselink, Rianne; Lassche, Saskia; Nillesen, Maartje; Sprengers, André; Verdonschot, Nico; van Alfen, Nens; de Korte, Chris

2017-11-01

A need exists for biomarkers to diagnose, quantify and longitudinally follow facioscapulohumeral muscular dystrophy (FSHD) and many other neuromuscular disorders. Furthermore, the pathophysiological mechanisms leading to muscle weakness in most neuromuscular disorders are not completely understood. Dynamic ultrasound imaging (B-mode image sequences) in combination with speckle tracking is an easy, applicable and patient-friendly imaging tool to visualize and quantify muscle deformation. This dynamic information provides insight in the pathophysiological mechanisms and may help to distinguish the various stages of diseased muscle in FSHD. In this proof-of-principle study, we applied a speckle tracking technique to 2-D ultrasound image sequences to quantify the deformation of the tibialis anterior muscle in patients with FSHD and in healthy controls. The resulting deformation patterns were compared with muscle ultrasound echo intensity analysis (a measure of fat infiltration and dystrophy) and clinical outcome measures. Of the four FSHD patients, two patients had severe peroneal weakness and two patients had mild peroneal weakness on clinical examination. We found a markedly varied muscle deformation pattern between these groups: patients with severe peroneal weakness showed a different motion pattern of the tibialis anterior, with overall less displacement of the central tendon region, while healthy patients showed a non-uniform displacement pattern, with the central aponeurosis showing the largest displacement. Hence, dynamic muscle ultrasound of the tibialis anterior muscle in patients with FSHD revealed a distinctively different tissue deformation pattern among persons with and without tibialis anterior weakness. These findings could clarify the understanding of the pathophysiology of muscle weakness in FSHD patients. In addition, the change in muscle deformation shows good correlation with clinical measures and quantitative muscle ultrasound measurements. In conclusion, dynamic ultrasound in combination with speckle tracking allows the study of the effects of muscle pathology in relation to strength, force transmission and movement generation. Although further research is required, this technique can develop into a biomarker to quantify muscle disease severity. Copyright © 2017 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Size Effect of Ground Patterns on FM-Band Cross-Talks between Two Parallel Signal Traces of Printed Circuit Boards for Vehicles

NASA Astrophysics Data System (ADS)

Iida, Michihira; Maeno, Tsuyoshi; Wang, Jianqing; Fujiwara, Osamu

Electromagnetic disturbances in vehicle-mounted radios are mainly caused by conducted noise currents flowing through wiring-harnesses from vehicle-mounted printed circuit boards (PCBs) with common slitting ground patterns. To suppress these kinds of noise currents, we previously measured them for simple two-layer PCBs with two parallel signal traces and slitting or non-slitting ground patterns, and then investigated by the FDTD simulation the reduction characteristics of the FM-band cross-talk noise levels between two parallel signal traces on six simple PCB models having different slitting ground or different divided ground patterns parallel to the traces. As a result, we found that the contributory factor for the FM-band cross-talk reduction is the reduction of mutual inductance between the two parallel traces, and also the noise currents from PCBs can rather be suppressed even if the size of the return ground becomes small. In this study, to investigate this finding, we further simulated the frequency characteristics of cross-talk reduction for additional six simple PCB models with different dividing dimensions ground patterns parallel to the traces, which revealed an interesting phenomenon that cross-talk reduction characteristics do not always decrease with increasing the width between the divided ground patterns.

Response of explosive HMX to low-velocity impact: modeling by the crystal plasticity finite element method

NASA Astrophysics Data System (ADS)

Ilnitsky, Denis; Inogamov, Nail; Zhakhovsky, Vasily

2017-12-01

Crystal plasticity finite element method (CPFEM) is a powerful tool for modeling the various deformation problems, which takes into account the different plasticity mechanisms at microscale of grain sizes and contribution of anisotropic behavior of each grain to macroscopic deformation pattern. Using this method we simulated deformation and plasticity of high explosive HMX produced by relatively low velocity impact. It was found that such plastic deformations of grains cause local heating which is sufficient to induce chemical reactions.

Stability and subsidence across Rome (Italy) in 2011-2013 based on COSMO-SkyMed Persistent Scatterer Interferometry

NASA Astrophysics Data System (ADS)

Francesca, Cigna; Lasaponara, Rosa; Nicola, Masini; Pietro, Milillo; Deodato, Tapete

2015-04-01

Ground stability of the built environment of the city of Rome in central Italy has been extensively investigated in the last years by using Interferometric Synthetic Aperture Radar (InSAR), with focus on deformation of both the monuments of the historic centre (e.g., [1-2]) and the southern residential quarters (e.g., [3]). C-band ERS-1/2 and ENVISAT ASAR time series deformation analyses brought evidence of overall stability across the town centre, except for localized deformation concentrated in areas geologically susceptible to instability (e.g. western slope of the Palatine Hill), whereas clear subsidence patterns were detected over the compressible alluvial deposits lying in proximity of the Tiber River. To retrieve an updated picture of stability and subsidence across the city, we analysed a time series of 32 COSMO-SkyMed StripMap HIMAGE, right-looking, ascending mode scenes with an image swath of 40 km, 3-m resolution and HH polarization, acquired between 21 March 2011 and 10 June 2013, with repeat cycle mostly equal to 16 days. Persistent Scatterer Interferometry (PSI) processing was undertaken by using the Stanford Method for Persistent Scatterers (StaMPS) as detailed in [4], and more than 310,000 radar targets (i.e. PS) were identified, with an average target density of over 2,800 PS/km2. The performance of StaMPS to retrieve satisfactory PS coverage over the urban features of interest was assessed against their orientation and visibility to the satellite Line-Of-Sight, as well as their conservation history throughout the biennial investigated (2011-2013). In this work we discuss effects due to local land cover and land use by exploiting the Global Monitoring for Environment and Security (GMES) European Urban Atlas (IT001L) of Rome at 1:10,000 scale, thereby also evaluating the capability of the X-band to spatially resolve targets coinciding with man-made structures in vegetated areas. Based on this assessment, our PSI results highlight those environmental constraints that can prevent, even at such high spatial resolution, obtaining satisfactory PS densities in peri-urban areas with high vegetation coverage. With regard to recent deformation patterns, COSMO-SkyMed time series confirm the persistence of subsidence processes in southern Rome. In areas of recent urbanization, such as that surrounding the Basilica of St Paul Outside-the-Walls, the estimated vertical motion velocity reaches values higher than -7.0 mm/yr. Further proof of the potentiality of COSMO-SkyMed constellation to extend almost seamlessly ground motion time series from previous SAR missions is offered by the deformation detected at the single-monument scale over the archaeological ruins of the Oppian Hill, the monuments and historical building in the riverside quarter of Trastevere, and the Basilica di San Saba within the Aurelian Walls. References [1] Tapete, D.; Fanti, R.; Cecchi, R.; Petrangeli, P.; Casagli, N. Satellite radar interferometry for monitoring and early-stage warning of structural instability in archaeological sites. J. Geophys. Eng. 2012, 9 S10-S25. [2] Tapete, D.; Casagli, N.; Fanti, R. Radar interferometry for early stage warning on monuments at risk. In Landslide Science and Practice; Margottini, C., Canuti, P., Sassa, K., Eds.; Springer: Berlin/Heidelberg, Germany, 2013; Volume 1, pp. 619-625. [3] Stramondo, S.; Bozzano, F.; Marra, F.; Wegmuller, U.; Cinti, F.R.; Moro, M.; Saroli, M. Subsidence induced by urbanisation in the city of Rome detected by advanced InSAR technique and geotechnical investigations. Remote Sens. Environ. 2008, 112, 3160-3172. [4] Cigna, F.; Lasaponara, R.; Masini, N.; Milillo, P.; Tapete, D. Persistent Scatterer Interferometry Processing of COSMO-SkyMed StripMap HIMAGE Time Series to Depict Deformation of the Historic Centre of Rome, Italy. Remote Sens. 2014, 6, 12593-12618.

Arctic patterned-ground ecosystems: A synthesis of field studies and models along a North American Arctic Transect

Treesearch

Walker D.A.; Romanovsky V.E.; Ping C.L.; Michaelson G.J.; Daanen R.P.; Shur Y.; Peterson R.A.; Krantz W.B.; Raynolds M.K.; William Gould; Grizelle Gonzalez; Nicolsky D.J.; Vonlanthen C.M.; Kade A.N.; Kuss P.; Kelley A.M.; Munger C.A.; Tarnocai C.T.; Matveyeva N.V.; Daniels F.J.A.

2008-01-01

Arctic landscapes have visually striking patterns of small polygons, circles, and hummocks. The linkages between the geophysical and biological components of these systems and their responses to climate changes are not well understood. The “Biocomplexity of Patterned Ground Ecosystems” project examined patterned-ground features (PGFs) in all five Arctic bioclimate...

Spin singlet and spin triplet pairing correlations on shape evolution in s d -shell N =Z Nuclei

NASA Astrophysics Data System (ADS)

Ha, Eunja; Cheoun, Myung-Ki; Sagawa, H.

2018-02-01

We study the shape evolution of N =Z nuclei 24Mg,28Si, and 32S in the axially symmetric deformed Woods-Saxon model, taking into account both T =0 and T =1 pairing interactions. We find the coexistence of T =0 and T =1 superfluidity phases in the large deformation region | β2|>0.3 in these three nuclei. The interplay between the two pairing interactions has an important effect on determining the deformation of the ground states in these nuclei. The self-energy contributions from the pairing correlations to the single particle (s.p.) energies are also examined.

Effect of Slag Impregnation on Macroscopic Deformation of Bauxite-Based Material

NASA Astrophysics Data System (ADS)

Coulon, Antoine; De Bilbao, Emmanuel; Michel, Rudy; Bouchetou, Marie-Laure; Brassamin, Séverine; Gazeau, Camille; Zanghi, Didier; Poirier, Jacques

This work aims at studying the volume change of bauxite corroded by a molten slag. Cylindrical samples were prepared by mixing ground bauxite with slag. Optical measurement at high temperature (1450 °C) of deformation with a high-resolution camera has been developed. Image processing allowed for determining the change in diameter of the sample. We showed that the deformation was induced by the precipitation of new expansive crystallised phases observed by SEM-EDS analyses. Adding pellets of the same slag upon the samples allowed to emphasize the effect of the slag amount on the size change. The change in diameter significantly increased in the impregnated area.

Monitoring of Deformation in Ground Before and After Tunnel Excavation

NASA Astrophysics Data System (ADS)

Eren, Mehmet; Hilmi Erkoç, Muharrem

2017-04-01

As population increase in metropolitan city, we need transportation and transmission tunnel. In this context, the engineers and administors attach impotance to building and planning underground-tunnel. Moreover, we must at regular intervals monitoring to deformation in underground-tunnel for quality and safety. Firstly, a deformation monitoring network is designed as perpendicular to the tunnel main axis. Secondly, the prescribed number of deformation measurements must be made. Finally, the deformation analysis is evaluated and its results is interpreted. This study investigates how deformation in monitoring network during and after tunnel excavate change.For this purpose, a deformation monitoring network of 18 object point and 4 reference point was established. Object points networks was designed steeply to the tunnel main axis as 3 cross section. Each cross section consisted of 3 point left, 2 point right and 1 point at the flowing line. Initial conditional measurement was made before tunnel excavation. Then the deformation measurement was made 5 period (1 period measured after tunnel excavate). All data sets were adjusted according to free adjustment method. The results from the investigation considering the tunnel line, a symmetrical subsidence was observed. The following day of tunnel excavation, we were observed %68 per of the total deformation. At the end of the last period measurements, %99 per of the total deformation was detected. Keywords: Tunnel, Deformation, Subsidence, Excavation

The implications of gas slug ascent in a stratified magma for acoustic and ground deformation source mechanisms in Strombolian eruptions

NASA Astrophysics Data System (ADS)

Capponi, Antonio; Lane, Stephen J.; James, Mike R.

2017-06-01

The interpretation of geophysical measurements at active volcanoes is vital for hazard assessment and for understanding fundamental processes such as magma degassing. For Strombolian activity, interpretations are currently underpinned by first-order fluid dynamic models which give relatively straightforward relationships between geophysical signals and gas and magma flow. However, recent petrological and high-speed video evidence has indicated the importance of rheological stratification within the conduit and, here, we show that under these conditions, the straightforward relationships break down. Using laboratory analogue experiments to represent a rheologically-stratified conduit we characterise the distinct variations in the shear stress exerted on the upper sections of the flow tube and in the gas pressures measured above the liquid surface, during different degassing flow configurations. These signals, generated by varying styles of gas ascent, expansion and burst, can reflect field infrasonic measurements and ground motion proximal to a vent. The shear stress signals exhibit timescales and trends in qualitative agreement with the near-vent inflation-deflation cycles identified at Stromboli. Therefore, shear stress along the uppermost conduit may represent a plausible source of near-vent tilt, and conduit shear contributions should be considered in the interpretation of ground deformation, which is usually attributed to pressure sources only. The same range of flow processes can produce different experimental infrasonic waveforms, even for similar masses of gas escape. The experimental data resembled infrasonic waveforms acquired from different vents at Stromboli associated with different eruptive styles. Accurate interpretation of near-vent ground deformation, infrasonic signal and eruptive style therefore requires detailed understanding of: a) spatiotemporal magma rheology in the shallow conduit, and b) shallow conduit geometry, as well as bubble overpressure and volume.

Kinematics, Exhumation, and Sedimentation of the North Central Andes (Bolivia): An Integrated Thermochronometer and Thermokinematic Modeling Approach

NASA Astrophysics Data System (ADS)

Rak, Adam J.; McQuarrie, Nadine; Ehlers, Todd A.

2017-11-01

Quantifying mountain building processes in convergent orogens requires determination of the timing and rate of deformation in the overriding plate. In the central Andes, large discrepancies in both timing and rate of deformation prevent evaluating the shortening history in light of internal or external forcing factors. Geologic map patterns, age and location of reset thermochronometer systems, and synorogenic sediment distribution are all a function of the geometry, kinematics, and rate of deformation in a fold-thrust-belt-foreland basin (FTB-FB) system. To determine the timing and rate of deformation in the northern Bolivian Andes, we link thermokinematic modeling to a sequentially forward modeled, balanced cross section isostatically accounting for thrust loads and erosion. Displacement vectors, in 10 km increments, are assigned variable ages to create velocity fields in a thermokinematic model for predicting thermochronometer ages. We match both the pattern of predicted cooling ages with the across strike pattern of measured zircon fission track, apatite fission track, and apatite (U-Th)/He cooling ages as well as the modeled age of FB formations to published sedimentary sections. Results indicate that northern Bolivian FTB deformation started at 50 Ma and may have begun as early as 55 Ma. Acceptable rates of shortening permit either a constant rate of shortening ( 4-5 mm/yr) or varying shortening rates with faster rates (7-10 mm/yr) at 45-50 Ma and 12-8 Ma, significantly slower rates (2-4 mm/yr) from 35 to 15 Ma and indicate the northern Bolivian Subandes started deforming between 19 and 14 Ma.

Influence of Tectonics on the Channel Pattern of Alaknanda River in Srinagar Valley (Garhwal Himalaya)

NASA Astrophysics Data System (ADS)

Datt, Devi

2017-04-01

This paper describes the results of a continuing investigation of tectonic influence on channel pattern and morphology of Alaknanda River in Lesser Garhwal Himalaya, Uttarakhand, India. Extensive field investigations using conventional methods supported by topographical sheets and remote sensing data (LISS IV), were undertaken.The results are classified into three sections :- tectonics, channel pattern and impact of tectonics on channel pattern. The channel length is divided into 8 meanders sets of 3 segments from Supana to Kirtinagar. Thereafter, a litho-tectonic map of the Srinagar valley was prepared. The style of active tectonics on deformation and characterization of fluvial landscape was investigated on typical strike-slip transverse faults near the zone of North Almora Thrust (NAT). NAT is a major tectonic unit of the Lesser Himalaya which passes through the northern margin from NW to SE direction.. The structural and lithological controls on the Alaknanda River system in Srinagar valley are reflected on distinct drainage patterns, abrupt change in flow direction, incised meandering, offset river channels, straight river lines, palaeo-channels, multi levels of terraces, knick points and pools in longitudinal profile. The results of the study show that the sinuosity index of the river is 1.35. Transverse faulting is very common along the NAT. An earlier generation of linear tectonic features were displaced by the latter phase of deformation. Significant deviations were observed in river channel at deformation junctions. Moreover, all 8 sets of meanders are strongly influenced by tectonic features. The meandering course is, thereby, correlated with tectonic features. It is shown that the river channel is strongly influenced by the tectonic features in the study area. Key Words: Tectonic, Meander, Channel pattern, deformation, Knick point.

Is there a relationship between foetal position and both preferred lying posture after birth and pattern of subsequent postural deformity in non-ambulant people with cerebral palsy?

PubMed

Porter, D; Michael, S; Kirkwood, C

2010-09-01

A pattern of postural deformity was observed in a previous study that included an association between direction of spinal curvature and direction of windsweeping with more windswept deformities occurring to the right and lateral spinal curvatures occurring convex to the left. The direction of this pattern was found to be associated with preferred lying posture in early life. The aim of this study was to test the association between foetal position and both the preferred lying posture after birth, and the direction of subsequent postural deformity in non-ambulant children with cerebral palsy (CP). A retrospective cohort study was carried out involving 60 participants at level five on the gross motor function classification for CP. Foetal position during the last month of pregnancy was taken from antenatal records and parents were interviewed to identify preferred lying posture in the first year of life. At the time of the physical assessment ages ranged from 1 year and 1 month to 19 years with a median age of 13 years and 1 month. Foetal presentation was found to be associated with the preferred lying posture with participants carried in a left occipito-anterior/lateral position more likely to adopt a supine head right lying posture, and vice versa. An association was also observed between the foetal position and asymmetrical postural deformity occurring later in life with participants carried in a left occipito-anterior/lateral presentation more likely to have a convex left spinal curve, a lower left pelvic obliquity, and a windswept hip pattern to the right. Clinicians should be aware of the association between foetal presentation, asymmetrical lying posture, and the direction of subsequent postural deformity for severely disabled children. A hypothesis is described that might help to explain these findings.

Sequence Dependencies of DNA Deformability and Hydration in the Minor Groove

PubMed Central

Yonetani, Yoshiteru; Kono, Hidetoshi

2009-01-01

Abstract DNA deformability and hydration are both sequence-dependent and are essential in specific DNA sequence recognition by proteins. However, the relationship between the two is not well understood. Here, systematic molecular dynamics simulations of 136 DNA sequences that differ from each other in their central tetramer revealed that sequence dependence of hydration is clearly correlated with that of deformability. We show that this correlation can be illustrated by four typical cases. Most rigid basepair steps are highly likely to form an ordered hydration pattern composed of one water molecule forming a bridge between the bases of distinct strands, but a few exceptions favor another ordered hydration composed of two water molecules forming such a bridge. Steps with medium deformability can display both of these hydration patterns with frequent transition. Highly flexible steps do not have any stable hydration pattern. A detailed picture of this correlation demonstrates that motions of hydration water molecules and DNA bases are tightly coupled with each other at the atomic level. These results contribute to our understanding of the entropic contribution from water molecules in protein or drug binding and could be applied for the purpose of predicting binding sites. PMID:19686662

Geodetic Insights into the Earthquake Cycle in a Fold and Thrust Belt

NASA Astrophysics Data System (ADS)

Ingleby, T. F.; Wright, T. J.; Butterworth, V.; Weiss, J. R.; Elliott, J.

2017-12-01

Geodetic measurements are often sparse in time (e.g. individual interferograms) and/or space (e.g. GNSS stations), adversely affecting our ability to capture the spatiotemporal detail required to study the earthquake cycle in complex tectonic systems such as subaerial fold and thrust belts. In an effort to overcome these limitations we combine 3 generations of SAR satellite data (ERS 1/2, Envisat & Sentinel-1a/b) to obtain a 25 year, high-resolution surface displacement time series over the frontal portion of an active fold and thrust belt near Quetta, Pakistan where a Mw 7.1 earthquake doublet occurred in 1997. With these data we capture a significant portion of the seismic cycle including the interseismic, coseismic and postseismic phases. Each satellite time series has been referenced to the first ERS-1 SAR epoch by fitting a ground deformation model to the data. This allows us to separate deformation associated with each phase and to examine their relative roles in accommodating strain and creating topography, and to explore the relationship between the earthquake cycle and critical taper wedge mechanics. Modeling of the coseismic deformation suggests a long, thin rupture with rupture length 7 times greater than rupture width. Rupture was confined to a 20-30 degree north-northeast dipping reverse fault or ramp at depth, which may be connecting two weak decollements at approximately 8 km and 13 km depth. Alternatively, intersections between the coseismic fault plane and pre-existing steeper splay faults underlying folds may have played a significant role in inhibiting rupture, as evidenced by intersection points bordering the rupture. These fault intersections effectively partition the fault system down-dip and enable long, thin ruptures. Postseismic deformation is manifest as uplift across short-wavelength folds at the thrust front, with displacement rates decreasing with time since the earthquake. Broader patterns of postseismic uplift are also observed surrounding the coseismic rupture in both the down- and up-dip directions. We examine how coseismic stress changes may be driving the postseismic deformation by jointly inverting the InSAR-derived displacements for the rupture and fault friction parameters using a rate-strengthening friction model.

Sumatra-Andaman Megathrust Earthquake Slip: Insights From Mechanical Modeling of ICESat Surface Deformation Measurements

NASA Astrophysics Data System (ADS)

Harding, D. J.; Miuller, J. R.

2005-12-01

Modeling the kinematics of the 2004 Great Sumatra-Andaman earthquake is limited in the northern two-thirds of the rupture zone by a scarcity of near-rupture geodetic deformation measurements. Precisely repeated Ice, Cloud, and Land Elevation Satellite (ICESat) profiles across the Andaman and Nicobar Islands provide a means to more fully document the spatial pattern of surface vertical displacements and thus better constrain geomechanical modeling of the slip distribution. ICESat profiles that total ~45 km in length cross Car Nicobar, Kamorta, and Katchall in the Nicobar chain. Within the Andamans, the coverage includes ~350 km on North, Central, and South Andaman Islands along two NNE and NNW-trending profiles that provide elevations on both the east and west coasts of the island chain. Two profiles totaling ~80 km in length cross South Sentinel Island, and one profile ~10 km long crosses North Sentinel Island. With an average laser footprint spacing of 175 m, the total coverage provides over 2700 georeferenced surface elevations measurements for each operations period. Laser backscatter waveforms recorded for each footprint enable detection of forest canopy top and underlying ground elevations with decimeter vertical precision. Surface elevation change is determined from elevation profiles, acquired before and after the earthquake, that are repeated with a cross-track separation of less than 100 m by precision pointing of the ICESat spacecraft. Apparent elevation changes associated with cross-track offsets are corrected according to local slopes calculated from multiple post-earthquake repeated profiles. The surface deformation measurements recorded by ICESat are generally consistent with the spatial distribution of uplift predicted by a preliminary slip distribution model. To predict co-seismic surface deformation, we apply a slip distribution, derived from the released energy distribution computed by Ishii et al. (2005), as the displacement discontinuity boundary condition on the Sumatra-Andaman subduction interface fault. The direction of slip on the fault surface is derived from the slip directions computed by Tsai et al. (in review) for centroid moment tensor focal mechanisms spatially distributed along the rupture. The slip model will be refined to better correspond to the observed surface deformation as additional results from the ICESat profiles become available.

Earthquake-induced soft-sediment deformation structures in Late Pleistocene lacustrine deposits of Issyk-Kul lake (Kyrgyzstan)

NASA Astrophysics Data System (ADS)

Gladkov, A. S.; Lobova, E. U.; Deev, E. V.; Korzhenkov, A. M.; Mazeika, J. V.; Abdieva, S. V.; Rogozhin, E. A.; Rodkin, M. V.; Fortuna, A. B.; Charimov, T. A.; Yudakhin, A. S.

2016-10-01

This paper discusses the composition and distribution of soft-sediment deformation structures induced by liquefaction in Late Pleistocene lacustrine terrace deposits on the southern shore of Issyk-Kul Lake in the northern Tien Shan mountains of Kyrgyzstan. The section contains seven deformed beds grouped in two intervals. Five deformed beds in the upper interval contain load structures (load casts and flame structures), convolute lamination, ball-and-pillow structures, folds and slumps. Deformation patterns indicate that a seismic trigger generated a multiple slump on a gentle slope. The dating of overlying subaerial deposits suggests correlation between the deformation features and strong earthquakes in the Late Pleistocene.

Spatiotemporal seismic velocity change in the Earth's subsurface associated with large earthquake: contribution of strong ground motion and crustal deformation

NASA Astrophysics Data System (ADS)

Sawazaki, K.

2016-12-01

It is well known that seismic velocity of the subsurface medium changes after a large earthquake. The cause of the velocity change is roughly attributed to strong ground motion (dynamic strain change), crustal deformation (static strain change), and fracturing around the fault zone. Several studies have revealed that the velocity reduction down to several percent concentrates at the depths shallower than several hundred meters. The amount of velocity reduction correlates well with the intensity of strong ground motion, which indicates that the strong motion is the primary cause of the velocity reduction. Although some studies have proposed contributions of coseismic static strain change and fracturing around fault zone to the velocity change, separation of their contributions from the site-related velocity change is usually difficult. Velocity recovery after a large earthquake is also widely observed. The recovery process is generally proportional to logarithm of the lapse time, which is similar to the behavior of "slow dynamics" recognized in laboratory experiments. The time scale of the recovery is usually months to years in field observations, while it is several hours in laboratory experiments. Although the factor that controls the recovery speed is not well understood, cumulative strain change due to post-seismic deformation, migration of underground water, mechanical and chemical reactions on the crack surface could be the candidate. In this study, I summarize several observations that revealed spatiotemporal distribution of seismic velocity change due to large earthquakes; especially I focus on the case of the M9.0 2011 Tohoku earthquake. Combining seismograms of Hi-net (high-sensitivity) and KiK-net (strong motion), geodetic records of GEONET and the seafloor GPS/Acoustic ranging, I investigate contribution of the strong ground motion and crustal deformation to the velocity change associated with the Tohoku earthquake, and propose a gross view of spatiotemporal velocity change due to large earthquakes. Acknowledgement: Hi-net and KiK-net seismograms (NIED), GEONET GNSS record (Geospatial Information Authority of Japan), and the JMA unified hypocenter catalog are used in this study.

The 2009 and 2010 eruptions and shallow intrusions at Piton de la Fournaise, La Réunion Island, seen by cGPS measurements

NASA Astrophysics Data System (ADS)

Staudacher, Thomas; Peltier, Aline; Boissier, Patrice; di Muro, Andrea

2010-05-01

The Piton de la Fournaise volcano at La Réunion Island in the western Indian Ocean is one of the most active volcanoes in the world. Its average eruption rate over the last 2 centuries is one eruption every 9 months. Between 1998 and 2010 thirty eruptions occurred and produced some 300×106 m3 of lava flows. Since the 2007 collapse of 340 m of the Dolomieu caldera, the eruptive activity of the volcano changed with mainly the occurrence of numerous shallow intrusions preceding days or weeks small summit eruptions. In 2009-2010, Piton de la Fournaise erupted successively in November 5, December 14, 2009 and in January 2, 2010. The one day lasting November and December 2009 eruptions started from en echelon fissures close to the summit around its eastern and southern rims, respectively, whereas the January 2010 eruptive fissure opened on the western flank inside of the Dolomieu crater. These three eruptions produced less than 106 m3 of lava, but generated large ground deformation, of up to 70 cm, recorded by the cGPS network of the volcano observatory and by cinematic GPS measurements. The long term survey showed a small extent of the ground deformation field and the small ratios of base/summit displacements and vertical/horizontal displacements reveal the involvement of shallow dykes to fed these successive eruptions. The cGPS network allowed us to follow up precisely the pre eruptive ground deformations, the 40 to 90 minutes dyke propagation toward the surface, as well as the ground deformations after the vent opening. For the November and December 2009 eruptions, the dyke started below the western part of the Dolomieu crater, before propagating to the east and the south, respectively. For the January eruption, the dyke propagated along a more or less vertical pathway directly to the western part of the Dolomieu crater. The two previous dyke injections of November and December had increased the horizontal compressive stress of the eastern side of the Dolomieu crater and did not favoured a new propagation to the east.

Variations of permeability and pore size distribution of porous media with pressure.

PubMed

Chen, Quan; Kinzelbach, Wolfgang; Ye, Chaohui; Yue, Yong

2002-01-01

Porosity and permeability of porous and fractured geological media decrease with the exploitation of formation fluids such as petroleum, natural gas, or ground water. This may result in ground subsidence and a decrease of recovery of petroleum, natural gas, or ground water. Therefore, an evaluation of the behavior of permeability and porosity under formation fluid pressure changes is important to petroleum and ground water industries. This study for the first time establishes a method, which allows for the measurement of permeability, porosity, and pore size distribution of cores simultaneously. From the observation of the pore size distribution by low-field nuclear magnetic resonance (NMR) relaxation time spectrometry the mechanisms of pressure-dependent porosity and permeability change can be derived. This information cannot be obtained by traditional methods. As the large-size pores or fractures contribute significantly to the permeability, their change consequently leads to a large permeability change. The contribution of fractures to permeability is even larger than that of pores. Thus, the permeability of the cores with fractures decreased more than that of cores without fractures during formation pressure decrease. Furthermore, it did not recover during formation pressure increase. It can be concluded that in fractures, mainly plastic deformation takes place, while matrix pores mainly show elastic deformation. Therefore, it is very important to keep an appropriate formation fluid pressure during the exploitation of ground water and petroleum in a fractured formation.

Paleoseismic evidence for dynamic surface rupturing in an intraplate setting (Lower Rhine Embayment, central Europe)

NASA Astrophysics Data System (ADS)

Kuebler, S.; Friedrich, A. M.; Strecker, M. R.

2011-12-01

One of the most enigmatic problems in intraplate earthquake geology is the spatio-temporal recurrence pattern of large earthquakes. Intraplate regions such as the New Madrid seismic zone or the central European rift system are subject to considerable seismic hazards, because fault activity is highly disparate in space and time and our knowledge about the recurrence of large earthquakes is still rudimentary. The current debate in central Europe ranges from slip dominated by repeated large coseismic events to slip dominated by aseismic creep. Here, field evidence in support of the former is sparse, and hence, some authors concluded that many faults move by slow aseismic creep rather than by ground rupturing earthquakes. We report new results from a paleoseismic study carried out in the Lower Rhine Embayment across a subsidiary normal fault in the area of Germany's largest historical earthquake (1756 AD, ML 6.2±0.2) that clearly revealed field evidence of dynamic surface faulting. At the trench site, the fault is covered by <5 m-thick Holocene fluvial gravel and flood deposits overlaying Devonian shale. We mapped a surface offset of ~1 m and a ~10 m wide zone of localized deformation expressed by abundant fractures with aligned and broken clasts extending vertically throughout the entire gravel. Mapping of 237 fractured clasts and the long-axis orientation of ~10.000 clasts defines a deformation zone coinciding with the surface offset and two offset markers within the gravel layers. We interpret these features as the result of coseismic deformation at the near-surface end of the rupture. We rule out alternative processes which may lead to fracturing of pebbles such as freeze-thaw weathering or sediment loading effects, since both the gravel fabric and fracture planes coincide well with the fault orientation. We preclude slow deformation due to aseismic creep as governing process to cause rupturing of pebbles this close to the surface, as this would require an overburden stress of several hundreds of meters according to modelling results (e. g. Eidelmann, 1992, Geology). With a significantly smaller overburden, as in this study, a high differential acceleration force, such as a shock wave produced by an earthquake rupture or a seismic wave would be needed to overcome the pebble's shear resistance. Preliminary radiocarbon data bracket the youngest event horizon to Latest Holocene age. In conclusion, we identified coseismic deformation at the trench site, because special conditions produced a number of features not usually observed in other fault exposures. The thin sedimentary cover (<5 m) above basement rocks and the high groundwater table, which may reduce the shear strength of the pebbles, may have played an important role in producing this deformation pattern. Our results imply that large surface rupturing earthquakes in low-strain intraplate regions may be more common than previously thought.

Implementing an empirical scalar constitutive relation for ice with flow-induced polycrystalline anisotropy in large-scale ice sheet models

NASA Astrophysics Data System (ADS)

Graham, Felicity S.; Morlighem, Mathieu; Warner, Roland C.; Treverrow, Adam

2018-03-01

The microstructure of polycrystalline ice evolves under prolonged deformation, leading to anisotropic patterns of crystal orientations. The response of this material to applied stresses is not adequately described by the ice flow relation most commonly used in large-scale ice sheet models - the Glen flow relation. We present a preliminary assessment of the implementation in the Ice Sheet System Model (ISSM) of a computationally efficient, empirical, scalar, constitutive relation which addresses the influence of the dynamically steady-state flow-compatible induced anisotropic crystal orientation patterns that develop when ice is subjected to the same stress regime for a prolonged period - sometimes termed tertiary flow. We call this the ESTAR flow relation. The effect on ice flow dynamics is investigated by comparing idealised simulations using ESTAR and Glen flow relations, where we include in the latter an overall flow enhancement factor. For an idealised embayed ice shelf, the Glen flow relation overestimates velocities by up to 17 % when using an enhancement factor equivalent to the maximum value prescribed in the ESTAR relation. Importantly, no single Glen enhancement factor can accurately capture the spatial variations in flow across the ice shelf generated by the ESTAR flow relation. For flow line studies of idealised grounded flow over varying topography or variable basal friction - both scenarios dominated at depth by bed-parallel shear - the differences between simulated velocities using ESTAR and Glen flow relations depend on the value of the enhancement factor used to calibrate the Glen flow relation. These results demonstrate the importance of describing the deformation of anisotropic ice in a physically realistic manner, and have implications for simulations of ice sheet evolution used to reconstruct paleo-ice sheet extent and predict future ice sheet contributions to sea level.

Comparison of coseismic near-field and off-fault surface deformation patterns of the 1992 Mw 7.3 Landers and 1999 Mw 7.1 Hector Mine earthquakes: Implications for controls on the distribution of surface strain

NASA Astrophysics Data System (ADS)

Milliner, C. W. D.; Dolan, J. F.; Hollingsworth, J.; Leprince, S.; Ayoub, F.

2016-10-01

Subpixel correlation of preevent and postevent air photos reveal the complete near-field, horizontal surface deformation patterns of the 1992 Mw 7.3 Landers and 1999 Mw 7.1 Hector Mine ruptures. Total surface displacement values for both earthquakes are systematically larger than "on-fault" displacements from geologic field surveys, indicating significant distributed, inelastic deformation occurred along these ruptures. Comparison of these two data sets shows that 46 ± 10% and 39 ± 22% of the total surface deformation were distributed over fault zones averaging 154 m and 121 m in width for the Landers and Hector Mine events, respectively. Spatial variations of distributed deformation along both ruptures show correlations with the type of near-surface lithology and degree of fault complexity; larger amounts of distributed shear occur where the rupture propagated through loose unconsolidated sediments and areas of more complex fault structure. These results have basic implications for geologic-geodetic rate comparisons and probabilistic seismic hazard analysis.

A Case Study on the Strata Movement Mechanism and Surface Deformation Regulation in Chengchao Underground Iron Mine

NASA Astrophysics Data System (ADS)

Cheng, Guanwen; Chen, Congxin; Ma, Tianhui; Liu, Hongyuan; Tang, Chunan

2017-04-01

The regular pattern of surface deformation and the mechanism of underground strata movement, especially in iron mines constructed with the block caving method, have a great influence on infrastructure on the surface, so they are an important topic for research. Based on the engineering geology conditions and the surface deformation and fracture features in Chengchao Iron Mine, the mechanism of strata movement and the regular pattern of surface deformation in the footwall were studied by the geomechanical method, and the following conclusions can be drawn: I. The surface deformation process is divided into two stages over time, i.e., the chimney caving development stage and the post-chimney deformation stage. Currently, the surface deformation in Chengchao Iron Mine is at the post-chimney deformation stage. II. At the post-chimney deformation stage, the surface deformation and geological hazards in Chengchao Iron Mine are primarily controlled by the NWW-trending joints, with the phenomenon of toppling deformation and failure on the surface. Based on the surface deformation characteristics in Chengchao Iron Mine, the surface deformation area can be divided into the following four zones: the fracture extension zone, the fracture closure zone, the fracture formation zone and the deformation accumulation zone. The zones on the surface can be determined by the surface deformation characteristics. III. The cantilever beams near the chimney caving area, caused by the NWW-trending joints, have been subjected to toppling failure. This causes the different deformation and failure mechanisms in different locations of the deep rock mass. The deep rock can be divided into four zones, i.e., the fracture zone, fracture transition zone, deformation zone and undisturbed zone, according to the different deformation and failure mechanisms. The zones in the deep rock are the reason for the zones on the surface, so they can be determined by the zones on the surface. Through these findings, the degree of damage to the infrastructure in different locations can be determined based on the surface deformation zones. As the mining continues deeper, the development regulation of the zones on the surface and in deep rock mass can be further studied based on the zones in the deep rock.

Rapid modeling of complex multi-fault ruptures with simplistic models from real-time GPS: Perspectives from the 2016 Mw 7.8 Kaikoura earthquake

NASA Astrophysics Data System (ADS)

Crowell, B.; Melgar, D.

2017-12-01

The 2016 Mw 7.8 Kaikoura earthquake is one of the most complex earthquakes in recent history, rupturing across at least 10 disparate faults with varying faulting styles, and exhibiting intricate surface deformation patterns. The complexity of this event has motivated the need for multidisciplinary geophysical studies to get at the underlying source physics to better inform earthquake hazards models in the future. However, events like Kaikoura beg the question of how well (or how poorly) such earthquakes can be modeled automatically in real-time and still satisfy the general public and emergency managers. To investigate this question, we perform a retrospective real-time GPS analysis of the Kaikoura earthquake with the G-FAST early warning module. We first perform simple point source models of the earthquake using peak ground displacement scaling and a coseismic offset based centroid moment tensor (CMT) inversion. We predict ground motions based on these point sources as well as simple finite faults determined from source scaling studies, and validate against true recordings of peak ground acceleration and velocity. Secondly, we perform a slip inversion based upon the CMT fault orientations and forward model near-field tsunami maximum expected wave heights to compare against available tide gauge records. We find remarkably good agreement between recorded and predicted ground motions when using a simple fault plane, with the majority of disagreement in ground motions being attributable to local site effects, not earthquake source complexity. Similarly, the near-field tsunami maximum amplitude predictions match tide gauge records well. We conclude that even though our models for the Kaikoura earthquake are devoid of rich source complexities, the CMT driven finite fault is a good enough "average" source and provides useful constraints for rapid forecasting of ground motion and near-field tsunami amplitudes.

Monitoring unrest in a large silicic caldera, the long Valley-inyo craters volcanic complex in east-central California

USGS Publications Warehouse

Hill, D.P.

1984-01-01

Recent patterns of geologic unrest in long Valley caldera in east-central California emphasize that this large, silicic volcanic system and the adjacent, geologically youthful Inyo-Mono Craters volcanic chain are still active and capable of producing locally hazardous volcanic eruptions. A series of four magnitude -6 earthquakes in May 1980 called attention to this current episode of unrest, and subsequent activity has included numerous earthquake swarms in the south moat of the caldera accompanied by inflation of the resurgent dome by more than 50 cm over the last five years. The seismicity associated with this unrest is currently monitored by a network of 31 telemetered seismic stations with an automatic processing system that yelds hypocentral locations and earthquake magnitudes in near-real time. Deformation of the ground is monitored by a) a series of overlapping trilateration networks that provide coverage ranging from annual measurements of regional deformation to daily measurements of deformation local to the active, southern section of the caldera, b) a regional network of level lines surveyed annually, c) a regional network of precise gravity stations occupied annually, d) local, L-shaped level figures surveyed every few months, and e) a network of fourteen borehole tiltmeter clusters (two instruments in each cluster) and a borehole dilatometer, the telemetered signals from which provide continuous data on deformation rates. Additional telemetered data provide continuous information on fluctuations in the local magnetic field, hydrogen gas emission rates at three sites, and water level and temperatures in three wells. Continuous data on disharge rates and temperatures from hot springs and fumaroles are collected by several on-site recorders within the caldera, and samples for liquid and gas chemistry are collected several times per year from selected hot springs and fumaroles. ?? 1984 Intern. Association of Volcanology and Chemistry of the Earth's Interior.

Image analysis of ocular fundus for retinopathy characterization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ushizima, Daniela; Cuadros, Jorge

2010-02-05

Automated analysis of ocular fundus images is a common procedure in countries as England, including both nonemergency examination and retinal screening of patients with diabetes mellitus. This involves digital image capture and transmission of the images to a digital reading center for evaluation and treatment referral. In collaboration with the Optometry Department, University of California, Berkeley, we have tested computer vision algorithms to segment vessels and lesions in ground-truth data (DRIVE database) and hundreds of images of non-macular centric and nonuniform illumination views of the eye fundus from EyePACS program. Methods under investigation involve mathematical morphology (Figure 1) for imagemore » enhancement and pattern matching. Recently, we have focused in more efficient techniques to model the ocular fundus vasculature (Figure 2), using deformable contours. Preliminary results show accurate segmentation of vessels and high level of true-positive microaneurysms.« less

Crystal preferred orientations of minerals from mantle xenoliths in alkali basaltic rocks form the Catalan Volcanic Zone (NE Spain)

NASA Astrophysics Data System (ADS)

Fernández-Roig, Mercè; Galán, Gumer; Mariani, Elisabetta

2015-04-01

Mantle xenoliths in alkali basaltic rocks from the Catalan Volcanic Zone, associated with the Neogene-Quaternary rift system in NE Spain, are formed of anhydrous spinel lherzolites and harzburgites with minor olivine websterites. Both peridotites are considered residues of variable degrees of partial melting, later affected by metasomatism, especially the harzburgites. These and the websterites display protogranular microstructures, whereas lherzolites show continuous variation between protogranular, porphyroclastic and equigranular forms. Thermometric data of new xenoliths indicate that protogranular harzburgites, lherzolites and websterites were equilibrated at higher temperatures than porphyroclastic and equigranular lherzolites. Mineral chemistry also indicates lower equilibrium pressure for porphyroclastic and equigranular lherzolites than for the protogranular ones. Crystal preferred orientations (CPOs) of olivine and pyroxenes from these new xenoliths were determined with the EBSD-SEM technique to identify the deformation stages affecting the lithospheric mantle in this zone and to assess the relationships between the deformation fabrics, processes and microstructures. Olivine CPOs in protogranular harzburgites, lherzolites and a pyroxenite display [010]-fiber patterns characterized by a strong point concentration of the [010] axis normal to the foliation and girdle distribution of [100] and [001] axes within the foliation plane. Olivine CPO symmetry in porphyroclastic and equigranular lherzolites varies continuously from [010]-fiber to orthorhombic and [100]-fiber types. The orthorhombic patterns are characterized by scattered maxima of the three axes, which are normal between them. The rare [100]-fiber patterns display strong point concentration of [100] axis, with normal girdle distribution of the other two axes, which are aligned with each other. The patterns of pyroxene CPOs are more dispersed than those of olivine, especially for clinopyroxene, but there is good correlation between the [100] olivine axis and the [001] pyroxene axis in most protogranular peridotites. However, the [001] axes of the three silicates are parallel in equigranular and some porphyroclastic lherzolites. CPOs and misorientation axes indicate deformation by dislocation creep accommodated mainly by the [100](010) slip system for olivine and the [001](100), [001](010) for orthopyroxene. Also, subsidiary slip systems for olivine are [100]{0kl}, [001](100), [100](001) in porphyroclastic and equigranular lherzolites. The fabric strength of the three main silicates are consistent, all of them decreasing with grain size reduction. These results indicate that the lithospheric mantle in this area was affected by several deformation stages that took place at decreasing temperature and pressure. An earlier stage is preserved in protogranular peridotites and a pyroxenite, with olivine [010]-fiber patterns and consistent deformation of pyroxenes. It could be related to axial shortening, transpression and/or subsequent recovery and annealing. Later deformation stages would be recorded by most porphyroclastic and equigranular lherzolites characterized by orthorhombic and [100]-fiber patterns for olivine, and transitions between them and with the [010]-fiber one. These samples would come most likely from an active shear zone at shallower upper mantle depth, where deformation at higher strain rates would explain the olivine [100]-fiber symmetry. Transient deformation patterns for olivine, grain size reduction along with weakening of the fabric strength could be due to dynamic recrystallization through grain boundary migration and subgrain rotation mechanisms.

Monitoring dam structural health from space: Insights from novel InSAR techniques and multi-parametric modeling applied to the Pertusillo dam Basilicata, Italy

NASA Astrophysics Data System (ADS)

Milillo, Pietro; Perissin, Daniele; Salzer, Jacqueline T.; Lundgren, Paul; Lacava, Giusy; Milillo, Giovanni; Serio, Carmine

2016-10-01

The availability of new constellations of synthetic aperture radar (SAR) sensors is leading to important advances in infrastructure monitoring. These constellations offer the advantage of reduced revisit times, providing low-latency data that enable analysis that can identify infrastructure instability and dynamic deformation processes. In this paper we use COSMO-SkyMed (CSK) and TerraSAR-X (TSX) data to monitor seasonal induced deformation at the Pertusillo dam (Basilicata, Italy) using multi-temporal SAR data analysis. We analyzed 198 images spanning 2010-2015 using a coherent and incoherent PS approach to merge COSMO-SkyMed adjacent tracks and TerraSAR-X acquisitions, respectively. We used hydrostatic-seasonal-temporal (HST) and hydrostatic-temperature-temporal (HTT) models to interpret the non-linear deformation at the dam wall using ground measurements together with SAR time-series analysis. Different look geometries allowed us to characterize the horizontal deformation field typically observed at dams. Within the limits of our models and the SAR acquisition sampling we found that most of the deformation at the Pertusillo dam can be explained by taking into account only thermal seasonal dilation and hydrostatic pressure. The different models show slightly different results when interpreting the aging term at the dam wall. The results highlight how short-revisit SAR satellites in combination with models widely used in the literature for interpreting pendulum and GPS data can be used for supporting structural health monitoring and provide valuable information to ground users directly involved in field measurements.

Efficient inversion of volcano deformation based on finite element models : An application to Kilauea volcano, Hawaii

NASA Astrophysics Data System (ADS)

Charco, María; González, Pablo J.; Galán del Sastre, Pedro

2017-04-01

The Kilauea volcano (Hawaii, USA) is one of the most active volcanoes world-wide and therefore one of the better monitored volcanoes around the world. Its complex system provides a unique opportunity to investigate the dynamics of magma transport and supply. Geodetic techniques, as Interferometric Synthetic Aperture Radar (InSAR) are being extensively used to monitor ground deformation at volcanic areas. The quantitative interpretation of such surface ground deformation measurements using geodetic data requires both, physical modelling to simulate the observed signals and inversion approaches to estimate the magmatic source parameters. Here, we use synthetic aperture radar data from Sentinel-1 radar interferometry satellite mission to image volcano deformation sources during the inflation along Kilauea's Southwest Rift Zone in April-May 2015. We propose a Finite Element Model (FEM) for the calculation of Green functions in a mechanically heterogeneous domain. The key aspect of the methodology lies in applying the reciprocity relationship of the Green functions between the station and the source for efficient numerical inversions. The search for the best-fitting magmatic (point) source(s) is generally conducted for an array of 3-D locations extending below a predefined volume region. However, our approach allows to reduce the total number of Green functions to the number of the observation points by using the, above mentioned, reciprocity relationship. This new methodology is able to accurately represent magmatic processes using physical models capable of simulating volcano deformation in non-uniform material properties distribution domains, which eventually will lead to better description of the status of the volcano.

Magma reservoir subsidence mechanics: Theoretical summary and application to Kilauea Volcano, Hawaii

NASA Astrophysics Data System (ADS)

Ryan, Michael P.; Blevins, James Y. K.; Okamura, Arnold T.; Koyanagi, Robert Y.

1983-05-01

An analytic model has been developed for the prediction of the three-dimensional deformation field generated by the withdrawal of magma from a sill-like storage compartment during an intrusion or eruption cycle. The model is based on the work of Berry and Sales (1961, 1962) and predicts the vertical displacement components over the areal plane. Model parameters are the depth of burial h, the intrusion half width a, the intrusion half length b, the thickness of the magmatic interior at the moment of melt withdrawal tm, and the planform aspect ratio ξ = a/b. The products of the model include areal deformation maps. Systematic variation in model parameters within the context of Kilauea Volcano, Hawaii, have revealed that circular and elliptical deformation patterns result from the collapse of draining rectilinear intrusions at depth. Moreover, the geometric parameters of a storage compartment may interact in complex ways to produce similar deformation patterns. The model has been applied to Kilauea Volcano for three periods of pronounced summit subsidence: (1) 1921-1927 (bracketing the steamblast eruptive phases of 1924); (2) June 1972 to December 1972, and (3) December 1972 to May 1973. Application of the model requires the simultaneous optimization of five predicted deformation features with respect to field measurements and the derivative deformation maps: (1) the vertical displacement maxima; (2) the vertical displacement gradients over the areal plane, (3) the lateral extent of the deformation field, (4) the aspect ratio of the subsidence pattern, and (5) the strike of the major axis of the deformation field. The constrained geometries and volumes of the inferred collapsed storage cavities for each period are (1) 1921-1927: depth ≅ 3 km, a ≅ 1500 m, b ≅ 4500 m, tm ≅ 20 m, V 540×106 m3, (2) June 1972 to December 1972: depth ≅ 3.3 km, a ≅ 600 m, b ≅ 2000 m, tm ≅ 1 m, V ≅ 4.8×106 m3, and (3) December 1972 to May 1973: depth ≅ 2.2 km, a ≅ 500 m, b ≅ 1612 m, tm ≅ 1 m, V ≅ 3.2×106 m3. For 2 and 3, calculated magmatic thicknesses tm happen to be in the range (3.48-0.15 m) of measurements for sill-like bodies in deeply dissected Hawaiian shield volcanoes. The fits obtained between calculated and observed deformation patterns allow quantification of the location, overall dimensions, orientation, and volume of the discrete, still molten, interior of sill-like compartments from which magma is tapped during eruption or intrusion.

Surface slip and off-fault deformation patterns in the 2013 MW 7.7 Balochistan, Pakistan earthquake: Implications for controls on the distribution of near-surface coseismic slip

NASA Astrophysics Data System (ADS)

Zinke, Robert; Hollingsworth, James; Dolan, James F.

2014-12-01

Comparison of 398 fault offsets measured by visual analysis of WorldView high-resolution satellite imagery with deformation maps produced by COSI-Corr subpixel image correlation of Landsat-8 and SPOT5 imagery reveals significant complexity and distributed deformation along the 2013 Mw 7.7 Balochistan, Pakistan earthquake. Average slip along the main trace of the fault was 4.2 m, with local maximum offsets up to 11.4 m. Comparison of slip measured from offset geomorphic features, which record localized slip along the main strand of the fault, to the total displacement across the entire width of the surface deformation zone from COSI-Corr reveals ˜45% off-fault deformation. While previous studies have shown that the structural maturity of the fault exerts a primary control on the total percentage of off-fault surface deformation, large along-strike variations in the percentage of strain localization observed in the 2013 rupture imply the influence of important secondary controls. One such possible secondary control is the type of near-surface material through which the rupture propagated. We therefore compared the percentage off-fault deformation to the type of material (bedrock, old alluvium, and young alluvium) at the surface and the distance of the fault to the nearest bedrock outcrop (a proxy for sediment thickness along this hybrid strike slip/reverse slip fault). We find significantly more off-fault deformation in younger and/or thicker sediments. Accounting for and predicting such off-fault deformation patterns has important implications for the interpretation of geologic slip rates, especially for their use in probabilistic seismic hazard assessments, the behavior of near-surface materials during coseismic deformation, and the future development of microzonation protocols for the built environment.

Perceptual transparency from image deformation.

PubMed

Kawabe, Takahiro; Maruya, Kazushi; Nishida, Shin'ya

2015-08-18

Human vision has a remarkable ability to perceive two layers at the same retinal locations, a transparent layer in front of a background surface. Critical image cues to perceptual transparency, studied extensively in the past, are changes in luminance or color that could be caused by light absorptions and reflections by the front layer, but such image changes may not be clearly visible when the front layer consists of a pure transparent material such as water. Our daily experiences with transparent materials of this kind suggest that an alternative potential cue of visual transparency is image deformations of a background pattern caused by light refraction. Although previous studies have indicated that these image deformations, at least static ones, play little role in perceptual transparency, here we show that dynamic image deformations of the background pattern, which could be produced by light refraction on a moving liquid's surface, can produce a vivid impression of a transparent liquid layer without the aid of any other visual cues as to the presence of a transparent layer. Furthermore, a transparent liquid layer perceptually emerges even from a randomly generated dynamic image deformation as long as it is similar to real liquid deformations in its spatiotemporal frequency profile. Our findings indicate that the brain can perceptually infer the presence of "invisible" transparent liquids by analyzing the spatiotemporal structure of dynamic image deformation, for which it uses a relatively simple computation that does not require high-level knowledge about the detailed physics of liquid deformation.

InSAR and GPS Time Series Analysis in Areas with Large Scale Hydrological Deformation: Separating Signal From Noise at Varying Length Scales in the San Joaquin Valley

NASA Astrophysics Data System (ADS)

Murray, K. D.; Lohman, R.

2017-12-01

Areas of large-scale subsidence are observed over much of the San Joaquin Valley of California due to the extraction of groundwater and hydrocarbons from the subsurface.These signals span regions with spatial extents of up to 100 km and have rates of up to 45 cm/yr or more. InSAR and GPS are complementary methods commonly used to measure such ground displacements and can provide important constraints on crustal deformation models, support groundwater studies, and inform water resource management efforts. However, current standard methods for processing these data sets and creating displacement time series are suboptimal for the deformation observed in areas like the San Joaquin Valley because (1) the ground surface properties are constantly changing due largely to agricultural activity, resulting in low coherence in half or more of a SAR frame, and (2) the deformation signals are distributed throughout the SAR frames, and are comparable to the size of the frames themselves. Therefore, referencing areas of deformation to non-deforming areas and correcting for long wavelength signals (e.g. atmospheric delays, orbital errors) is particularly difficult. We address these challenges by exploiting pixels that are stable in space and time, and use them for weighted spatial averaging and selective filtering before unwrapping. We then compare a range of methods for both long wavelength corrections and referencing via automatic partitioning of non-deforming areas, then benchmark results against continuous GPS measurements. Our final time series consist of nearly 15 years of displacement measurements from continuous GPS data, and Envisat, ALOS-1, Sentinel SAR data, and show significant temporal and spatial variations. We find that the choice of reference and long wavelength corrections can significantly bias long-term rate and seasonal amplitude estimates, causing variations of as much as 100% of the mean estimate. As we enter an era with free and open data access and regular observations plans from missions such as NISAR and the Sentinel constellation, our approach will help users evaluate the significance of observed deformation at a range of spatial scales and in areas with challenging surface properties.

SU-E-J-246: A Deformation-Field Map Based Liver 4D CBCT Reconstruction Method Using Gold Nanoparticles as Constraints

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, W; Zhang, Y; Ren, L

2014-06-01

Purpose: To investigate the feasibility of using nanoparticle markers to validate liver tumor motion together with a deformation field map-based four dimensional (4D) cone-beam computed tomography (CBCT) reconstruction method. Methods: A technique for lung 4D-CBCT reconstruction has been previously developed using a deformation field map (DFM)-based strategy. In this method, each phase of the 4D-CBCT is considered as a deformation of a prior CT volume. The DFM is solved by a motion modeling and free-form deformation (MM-FD) technique, using a data fidelity constraint and the deformation energy minimization. For liver imaging, there is low contrast of a liver tumor inmore » on-board projections. A validation of liver tumor motion using implanted gold nanoparticles, along with the MM-FD deformation technique is implemented to reconstruct onboard 4D CBCT liver radiotherapy images. These nanoparticles were placed around the liver tumor to reflect the tumor positions in both CT simulation and on-board image acquisition. When reconstructing each phase of the 4D-CBCT, the migrations of the gold nanoparticles act as a constraint to regularize the deformation field, along with the data fidelity and the energy minimization constraints. In this study, multiple tumor diameters and positions were simulated within the liver for on-board 4D-CBCT imaging. The on-board 4D-CBCT reconstructed by the proposed method was compared with the “ground truth” image. Results: The preliminary data, which uses reconstruction for lung radiotherapy suggests that the advanced reconstruction algorithm including the gold nanoparticle constraint will Resultin volume percentage differences (VPD) between lesions in reconstructed images by MM-FD and “ground truth” on-board images of 11.5% (± 9.4%) and a center of mass shift of 1.3 mm (± 1.3 mm) for liver radiotherapy. Conclusion: The advanced MM-FD technique enforcing the additional constraints from gold nanoparticles, results in improved accuracy for reconstructing on-board 4D-CBCT of liver tumor. Varian medical systems research grant.« less

Pure shear and simple shear calcite textures. Comparison of experimental, theoretical and natural data

USGS Publications Warehouse

Wenk, H.-R.; Takeshita, T.; Bechler, E.; Erskine, B.G.; Matthies, S.

1987-01-01

The pattern of lattice preferred orientation (texture) in deformed rocks is an expression of the strain path and the acting deformation mechanisms. A first indication about the strain path is given by the symmetry of pole figures: coaxial deformation produces orthorhombic pole figures, while non-coaxial deformation yields monoclinic or triclinic pole figures. More quantitative information about the strain history can be obtained by comparing natural textures with experimental ones and with theoretical models. For this comparison, a representation in the sensitive three-dimensional orientation distribution space is extremely important and efforts are made to explain this concept. We have been investigating differences between pure shear and simple shear deformation incarbonate rocks and have found considerable agreement between textures produced in plane strain experiments and predictions based on the Taylor model. We were able to simulate the observed changes with strain history (coaxial vs non-coaxial) and the profound texture transition which occurs with increasing temperature. Two natural calcite textures were then selected which we interpreted by comparing them with the experimental and theoretical results. A marble from the Santa Rosa mylonite zone in southern California displays orthorhombic pole figures with patterns consistent with low temperature deformation in pure shear. A limestone from the Tanque Verde detachment fault in Arizona has a monoclinic fabric from which we can interpret that 60% of the deformation occurred by simple shear. ?? 1987.

The surface geometry of inherited joint and fracture trace patterns resulting from active and passive deformation

NASA Technical Reports Server (NTRS)

Podwysocki, M. H.; Gold, D. P.

1974-01-01

Hypothetical models are considered for detecting subsurface structure from the fracture or joint pattern, which may be influenced by the structure and propagated to the surface. Various patterns of an initially orthogonal fracture grid are modeled according to active and passive deformation mechanisms. In the active periclinal structure with a vertical axis, fracture frequency increased both over the dome and basin, and remained constant with decreasing depth to the structure. For passive periclinal features such as a reef or sand body, fracture frequency is determined by the arc of curvature and showed a reduction over the reefmound and increased over the basin.

Orientation Dependence of the Deformation Microstructure of Ta-4%W after Cold-Rolling

NASA Astrophysics Data System (ADS)

Zhang, J.; Ma, G. Q.; Godfrey, A.; Shu, D. Y.; Chen, Q.; Wu, G. L.

2017-07-01

One of the common features of deformed face-centered cubic metals with medium to high stacking fault energy is the formation of geometrically necessary dislocation boundaries. The dislocation boundary arrangements in refractory metals with body-centered cubic crystal structure are, however, less well known. To address this issue a Ta-4%W alloy was cold rolled up to 70% in thickness in the present work. The resulting deformation microstructures were characterized by electron back-scattering diffraction and the dislocation boundary arrangements in each grain were revealed using sample-frame misorientation axis maps calculated using an in-house code. The maps were used to analyze the slip pattern of individual grains after rolling, revealing an orientation dependence of the slip pattern.

Preliminary deformation model for National Seismic Hazard map of Indonesia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meilano, Irwan; Gunawan, Endra; Sarsito, Dina

Preliminary deformation model for the Indonesia’s National Seismic Hazard (NSH) map is constructed as the block rotation and strain accumulation function at the elastic half-space. Deformation due to rigid body motion is estimated by rotating six tectonic blocks in Indonesia. The interseismic deformation due to subduction is estimated by assuming coupling on subduction interface while deformation at active fault is calculated by assuming each of the fault‘s segment slips beneath a locking depth or in combination with creeping in a shallower part. This research shows that rigid body motion dominates the deformation pattern with magnitude more than 15 mm/year, except inmore » the narrow area near subduction zones and active faults where significant deformation reach to 25 mm/year.« less

Crustal Deformation Associated With the 2000 Eruption and Degassing Process of Miyakejima, Izu Islands, Japan

NASA Astrophysics Data System (ADS)

Nishimura, T.; Ozawa, S.; Murakami, M.; Sagiya, T.; Yarai, H.; Tada, T.; Kaidzu, M.

2001-12-01

Miyakejima is located in the northern part of the Izu Islands lying along the boundary between the Pacific plate and the Philippine Sea plate. Miyakejima volcano erupted on Miyakejima is located in the northern part of the Izu Islands which are a chain of volcanoes lying along the boundary between the Pacific plate and the Philippine Sea plate. Miyakejima volcano erupted on June 27, 2000 after the quiescence of 17 years. First eruption is a small submarine eruption 1.5km off the western coast of Miyakejima. Subsequently, several summit eruptions as tephra ejecta occurred in July and August 2000. The summit collapsed just after the first summit eruption and a caldera was formed for 40 days. Collapsed volume and erupted volume are estimated to be 0.6km3 and 0.02km3, respectively. In September 2000, the collapse caldera started emitting a large amount of volcanic gasses. A peak amount of degassing SO2 is ~70000 ton/day in the period from October to December 2000. Amount of volcanic gas is decreasing gradually and is 15000 ton/day (SO2 ) now. However, it is still larger than other active volcanoes. Permanent GPS data reveals the spatial pattern and time evolution of ground deformation. Inflation of Miyakejima was observed by continuous GPS and leveling before the 2000 eruption. The observed displacements associated with the 2000 eruption show radial pattern suggesting shrinking of the island and subsidence. This pattern continues for 14 months from July 2000. Though the rate of crustal deformation is almost constant from July to August 2000, it is decreasing exponentially with a time constant of ~150days from September 2000. We assumed a point deflation source and inverted the observed displacement to estimate parameters of the point source. Volume decrease and depth of the deflation source is 0.12km3 and 4.2km from July to August 2000. We interpret that it is the squeezing of magma from a magma chamber of Miyakejima volcano. The displacement observed in neighbor islands suggests that the squeezed magma and collapsed material of Miyakejima migrated northwestward by as much as 30km in the form of a dike intrusion. Volume decrease and depth of the deflation source is 2.9km and 0.016km3 from September 2000 to May 2001. Decreasing rate of the deflation source is an order of magnitude smaller than that of the previous period. We considered that degassing from magma mainly causes the deflation of magma chamber after September 2000. The decreasing rate estimated from crustal deformation was quantitatively consistent with that estimated from the rate of the emitting volcanic gasses (Kazahaya, personal communication). This consideration suggests that the magma does not migrate any more and that the magma chamber is in closed system. However, recent rate of the deformation is much smaller than that calculated from the degassing rate. This implies that new magma is supplied to the magma chamber from deeper region or that the depth of magma head becomes deeper in a conduit from the magma chamber to the caldera.

Space Radar Image of Kilauea Volcano, Hawaii

NASA Image and Video Library

1999-05-01

This is a deformation map of the south flank of Kilauea volcano on the big island of Hawaii, centered at 19.5 degrees north latitude and 155.25 degrees west longitude. The map was created by combining interferometric radar data -- that is data acquired on different passes of the space shuttle which are then overlayed to obtain elevation information -- acquired by the Spaceborne Imaging Radar-C/X-band Synthetic Aperture Radar during its first flight in April 1994 and its second flight in October 1994. The area shown is approximately 40 kilometers by 80 kilometers (25 miles by 50 miles). North is toward the upper left of the image. The colors indicate the displacement of the surface in the direction that the radar instrument was pointed (toward the right of the image) in the six months between images. The analysis of ground movement is preliminary, but appears consistent with the motions detected by the Global Positioning System ground receivers that have been used over the past five years. The south flank of the Kilauea volcano is among the most rapidly deforming terrains on Earth. Several regions show motions over the six-month time period. Most obvious is at the base of Hilina Pali, where 10 centimeters (4 inches) or more of crustal deformation can be seen in a concentrated area near the coastline. On a more localized scale, the currently active Pu'u O'o summit also shows about 10 centimeters (4 inches) of change near the vent area. Finally, there are indications of additional movement along the upper southwest rift zone, just below the Kilauea caldera in the image. Deformation of the south flank is believed to be the result of movements along faults deep beneath the surface of the volcano, as well as injections of magma, or molten rock, into the volcano's "plumbing" system. Detection of ground motions from space has proven to be a unique capability of imaging radar technology. Scientists hope to use deformation data acquired by SIR-C/X-SAR and future imaging radar missions to help in better understanding the processes responsible for volcanic eruptions and earthquakes. http://photojournal.jpl.nasa.gov/catalog/PIA01758

Shear sensing based on a microstrip patch antenna

NASA Astrophysics Data System (ADS)

Mohammad, I.; Huang, H.

2012-10-01

A microstrip patch antenna sensor was studied for shear sensing with a targeted application of measuring plantar shear distribution on a diabetic foot. The antenna shear sensor consists of three components, namely an antenna patch, a soft foam substrate and a slotted ground plane. The resonant frequency of the antenna sensor is sensitive to the overlapping length between the slot in the ground plane and the antenna patch. A shear force applied along the direction of the slot deforms the foam substrate and causes a change in the overlapping length, which can be detected from the antenna frequency shift. The antenna shear sensor was designed based on simulated antenna frequency response and validated by experiments. Experimental results indicated that the antenna sensor exhibits high sensitivity to shear deformation and responds to the applied shear loads with excellent linearity and repeatability.

Development and Evaluation of Science and Technology Education Program Using Interferometric SAR

NASA Astrophysics Data System (ADS)

Ito, Y.; Ikemitsu, H.; Nango, K.

2016-06-01

This paper proposes a science and technology education program to teach junior high school students to measure terrain changes by using interferometric synthetic aperture radar (SAR). The objectives of the proposed program are to evaluate and use information technology by performing SAR data processing in order to measure ground deformation, and to incorporate an understanding of Earth sciences by analyzing interferometric SAR processing results. To draft the teaching guidance plan for the developed education program, this study considers both science and technology education. The education program was used in a Japanese junior high school. An educational SAR processor developed by the authors and the customized Delft object-oriented radar interferometric software package were employed. Earthquakes as diastrophism events were chosen as practical teaching materials. The selected events indicate clear ground deformation in differential interferograms with high coherence levels. The learners were able to investigate the ground deformations and disasters caused by the events. They interactively used computers and became skilled at recognizing the knowledge and techniques of information technology, and then they evaluated the technology. Based on the results of pre- and post-questionnaire surveys and self-evaluation by the learners, it was clarified that the proposed program was applicable for junior high school education, and the learners recognized the usefulness of Earth observation technology by using interferometric SAR. The usefulness of the teaching materials in the learning activities was also shown through the practical teaching experience.

Effect of Ground Patterns Size on FM-Band Cross-Talks between Two Parallel Signal Traces of Printed Circuit Boards for Vehicles

NASA Astrophysics Data System (ADS)

Iida, Michihira; Maeno, Tsuyoshi; Fujiwara, Osamu

It is well known that electromagnetic disturbances in vehicle-mounted radios are mainly caused by conducted noise currents flowing through wiring-harnesses from vehicle-mounted printed circuit boards (PCBs) with common ground patterns containing slits. To suppress the noise currents outflow from PCBs of these kinds, we previously measured noise currents outflow from simple two-layer PCBs having two parallel signal traces and different ground patterns with/without slits to reveal that making slits with open ends on the ground patterns in parallel with the traces can reduce the conducted noise currents. In the present study, with FDTD simulation, we investigated reduction effects of ground patterns size on the FM-band cross-talk noise levels between two parallel signal traces, by using four types of simple PCB models having different ground patterns formed in different numbers but containing the same planar dimension slits parallel to the traces, in addition to two types of PCB models with different ground patterns divided into two parts parallel to the traces. As a result, we found that the cross-talk noise currents for the above six types of PCBs decrease by 6.9-8.5dB compared to the PCB which has a plain ground with no slits. From this study, we got the finding that the contributing factor for the above mentioned cross-talk reduction relies on the reduction of mutual inductance between the two parallel traces. In addition, in case of this study, it is interesting to note that the noise currents outflow from PCBs can rather be suppressed when the size of the return ground of each signal trace is small.

Uppermost Mantle Deformation and Hydration Beneath the Gorda Plate Inferred from Pn Travel-times

NASA Astrophysics Data System (ADS)

VanderBeek, B. P.; Toomey, D. R.

2017-12-01

Deformation of the uppermost oceanic mantle is thought to occur primarily in response to divergence beneath mid-ocean ridges with little subsequent deformation off-axis. A notable exception to this is the Gorda plate where sinuous magnetic anomalies and numerous intra-plate earthquakes indicate diffuse, plate-wide deformation. Thus, the Gorda region provides a natural laboratory to investigate the non-rigid behavior of tectonic plates. We invert Pn (the seismic head wave refracted below the Moho) arrival times from 770 local earthquakes for epicentral and mantle anisotropic velocity parameters to understand how the surficial pattern of deformation translates into the uppermost 10 km of the mantle. Specifically, we ask does the pattern of seismic anisotropy reflect spreading-induced fabrics or has it been re-worked by extensive deformation of the Gorda plate? If it has been re-worked, does it reflect pervasive faulting of the uppermost mantle or plate-scale ductile deformation? And, are isotropic velocities anomalously slow suggesting significant mantle hydration? Preliminary results show that the average mantle velocity beneath Gorda is 7.55 km/s. Velocities vary azimuthally by 4% and the fast-propagation direction is sub-parallel to Pacific absolute plate motion (APM). In comparison, the uppermost mantle beneath the Juan de Fuca (JdF) plate is characterized by 4.6% anisotropy with a mean velocity of 7.85 km/s [VanderBeek and Toomey, 2017]; the fast propagation direction trends between the paleo-spreading direction and JdF APM. The reduced Gorda velocities may indicate a greater extent of fault-controlled hydration of the shallow mantle compared to the JdF plate. In both regions, the anisotropic structure argues against the notion that shallow mantle deformation ceases away from the ridge. Instead, shearing across Gorda due to differential motion between the Pacific and JdF plates [e.g. Bodmer et al., 2015] may cause broad scale ductile deformation and the realignment of shallow mantle fabrics. Beneath the JdF plate, the anisotropic signal is inferred to track the evolution of mantle flow as it evolves from divergence at the ridge to simple shear that is more closely aligned with APM. We discuss the rheologic implications of these observations and the patterns of mantle flow and deformation in Cascadia.

Effect of Ground Layer Patterns with Slits on Conducted Noise Currents from Printed Circuit Board

NASA Astrophysics Data System (ADS)

Maeno, Tsuyoshi; Unou, Takanori; Ichikawa, Kouji; Fujiwara, Osamu

Electromagnetic disturbances for vehicle-mounted radios can be caused by conducted noise currents that flows out from electronic equipment for vehicles to wire-harnesses. In this paper, for reducing the conducted noise currents from electronic equipment for vehicles, we made a simulation and experiment on how ground patterns affect the noise currents from three-layer printed circuit boards (PCBs) with slit-types and plane-type ground patterns. As a result, we could confirm that slits on a ground pattern allow conducted noise currents to flow out from PCBs to wire-harnesses. For the PCBs with plane-type ground and one of three slit-type patterns, on the other hand, both the simulation and examination showed that resonance phenomena occur at unexpected low-frequencies. A circuit analysis revealed that the above phenomena can be caused by the imbalance of a bridge circuit consisting of the trace circuits on the PCB.

SU-G-JeP3-04: Estimating 4D CBCT from Prior Information and Extremely Limited Angle Projections Using Structural PCA and Weighted Free-Form Deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Harris, W; Yin, F; Zhang, Y

Purpose: To investigate the feasibility of using structure-based principal component analysis (PCA) motion-modeling and weighted free-form deformation to estimate on-board 4D-CBCT using prior information and extremely limited angle projections for potential 4D target verification of lung radiotherapy. Methods: A technique for lung 4D-CBCT reconstruction has been previously developed using a deformation field map (DFM)-based strategy. In the previous method, each phase of the 4D-CBCT was generated by deforming a prior CT volume. The DFM was solved by a motion-model extracted by global PCA and a free-form deformation (GMM-FD) technique, using data fidelity constraint and the deformation energy minimization. In thismore » study, a new structural-PCA method was developed to build a structural motion-model (SMM) by accounting for potential relative motion pattern changes between different anatomical structures from simulation to treatment. The motion model extracted from planning 4DCT was divided into two structures: tumor and body excluding tumor, and the parameters of both structures were optimized together. Weighted free-form deformation (WFD) was employed afterwards to introduce flexibility in adjusting the weightings of different structures in the data fidelity constraint based on clinical interests. XCAT (computerized patient model) simulation with a 30 mm diameter lesion was simulated with various anatomical and respirational changes from planning 4D-CT to onboard volume. The estimation accuracy was evaluated by the Volume-Percent-Difference (VPD)/Center-of-Mass-Shift (COMS) between lesions in the estimated and “ground-truth” on board 4D-CBCT. Results: Among 6 different XCAT scenarios corresponding to respirational and anatomical changes from planning CT to on-board using single 30° on-board projections, the VPD/COMS for SMM-WFD was reduced to 10.64±3.04%/1.20±0.45mm from 21.72±9.24%/1.80±0.53mm for GMM-FD. Using 15° orthogonal projections, the VPD/COMS was further reduced to 1.91±0.86%/0.31±0.42mm based on SMM-WFD. Conclusion: Compared to GMM-FD technique, the SMM-WFD technique can substantially improve the 4D-CBCT estimation accuracy using extremely small scan angles to provide ultra-fast 4D verification. This work was supported by the National Institutes of Health under Grant No. R01-CA184173 and a research grant from Varian Medical Systems.« less

Very-long-period seismic signals - filling the gap between deformation and seismicity

NASA Astrophysics Data System (ADS)

Neuberg, Jurgen; Smith, Paddy

2013-04-01

Good broadband seismic sensors are capable to record seismic transients with dominant wavelengths of several tens or even hundreds of seconds. This allows us to generate a multi-component record of seismic volcanic events that are located in between the conventional high to low-frequency seismic spectrum and deformation signals. With a much higher temporal resolution and accuracy than e.g. GPS records, these signals fill the gap between seismicity and deformation studies. In this contribution we will review the non-trivial processing steps necessary to retrieve ground deformation from the original velocity seismogram and explore which role the resulting displacement signals have in the analysis of volcanic events. We use examples from Soufriere Hills volcano in Montserrat, West Indies, to discuss the benefits and shortcomings of such methods regarding new insights into volcanic processes.

Variable-intercept panel model for deformation zoning of a super-high arch dam.

PubMed

Shi, Zhongwen; Gu, Chongshi; Qin, Dong

2016-01-01

This study determines dam deformation similarity indexes based on an analysis of deformation zoning features and panel data clustering theory, with comprehensive consideration to the actual deformation law of super-high arch dams and the spatial-temporal features of dam deformation. Measurement methods of these indexes are studied. Based on the established deformation similarity criteria, the principle used to determine the number of dam deformation zones is constructed through entropy weight method. This study proposes the deformation zoning method for super-high arch dams and the implementation steps, analyzes the effect of special influencing factors of different dam zones on the deformation, introduces dummy variables that represent the special effect of dam deformation, and establishes a variable-intercept panel model for deformation zoning of super-high arch dams. Based on different patterns of the special effect in the variable-intercept panel model, two panel analysis models were established to monitor fixed and random effects of dam deformation. Hausman test method of model selection and model effectiveness assessment method are discussed. Finally, the effectiveness of established models is verified through a case study.

Present-day deformation across the Basin and Range Province, western United States

USGS Publications Warehouse

Thatcher, W.; Foulger, G.R.; Julian, B.R.; Svarc, J.; Quilty, E.; Bawden, G.W.

1999-01-01

The distribution of deformation within the Basin and Range province was determined from 1992, 1996, and 1998 surveys of a dense, 800-kilometer- aperture, Global Positioning System network, Internal deformation generally follows the pattern of Holocene fault distribution and is concentrated near the western extremity of the province, with lesser amounts focused near the eastern boundary. Little net deformation occurs across the central 500 kilometers of the network in western Utah and eastern Nevada. Concentration of deformation adjacent to the rigid Sierra Nevada block indicates that external plate-driving forces play an important role in driving deformation, modulating the extensional stress field generated by internal buoyancy forces that are due to lateral density gradients and topography near the province boundaries.

Lorentz symmetry violation and UHECR experiments

NASA Astrophysics Data System (ADS)

Gonzalez-Mestres, L.

2001-08-01

Lorentz symmetry violation (LSV) at Planck scale can be tested through ultra-high energy cosmic rays (UHECR). We discuss deformed Lorentz symmetry (DLS) and energy non-conservation (ENC) patterns where the effective LSV parameter varies like the square of the momentum scale (e.g. quadratically de-formed relativistic kinematics, QDRK). In such patterns, a ≈ 106 LSV at Planck scale would be enough to produce observable effects on the properties of cosmic rays at the ≈ 1020 eV scale: absence of GZK cutoff, stability of unstable particles, lower interaction rates, kinematical failure of any parton model and of standard formulae for Lorentz contraction and time dilation... Its phenomeno-logical implications are compatible with existing data. Precise signatures are discussed in several patterns. If the effective LSV or ENC parameter is taken to vary linearly with the momentum scale (e.g. linearly deformed relativistic kinematics, LDRK), contradictions seem to arise with UHECR data. Conse-quences are important for UHECR and high-energy gamma-ray exper iments, as well as for high-energy cosmic rays and gravitational waves.

Shape Transformations of Epithelial Shells

PubMed Central

Misra, Mahim; Audoly, Basile; Kevrekidis, Ioannis G.; Shvartsman, Stanislav Y.

2016-01-01

Regulated deformations of epithelial sheets are frequently foreshadowed by patterning of their mechanical properties. The connection between patterns of cell properties and the emerging tissue deformations is studied in multiple experimental systems, but the general principles remain poorly understood. For instance, it is in general unclear what determines the direction in which the patterned sheet is going to bend and whether the resulting shape transformation will be discontinuous or smooth. Here these questions are explored computationally, using vertex models of epithelial shells assembled from prismlike cells. In response to rings and patches of apical cell contractility, model epithelia smoothly deform into invaginated or evaginated shapes similar to those observed in embryos and tissue organoids. Most of the observed effects can be captured by a simpler model with polygonal cells, modified to include the effects of the apicobasal polarity and natural curvature of epithelia. Our models can be readily extended to include the effects of multiple constraints and used to describe a wide range of morphogenetic processes. PMID:27074691

Shape transition with temperature of the pear-shaped nuclei in covariant density functional theory

DOE PAGES

Zhang, Wei; Niu, Yi-Fei

2017-11-10

The shape evolutions of the pear-shaped nucleimore » $$^{224}$$Ra and even-even $$^{144-154}$$Ba with temperature are investigated by the finite-temperature relativistic mean field theory with the treatment of pairing correlations by the BCS approach. We study the free energy surfaces as well as the bulk properties including deformations, pairing gaps, excitation energy, and specific heat for the global minimum. For $$^{224}$$Ra, three discontinuities found in the specific heat curve indicate the pairing transition at temperature 0.4 MeV, and two shape transitions at temperatures 0.9 and 1.0 MeV, namely one from quadrupole-octupole deformed to quadrupole deformed, and the other from quadrupole deformed to spherical. Furthermore, the gaps at $N$=136 and $Z$=88 are responsible for stabilizing the octupole-deformed global minimum at low temperatures. Similar pairing transition at $$T\\sim$$0.5 MeV and shape transitions at $T$=0.5-2.2 MeV are found for even-even $$^{144-154}$$Ba. Finally, the transition temperatures are roughly proportional to the corresponding deformations at the ground states.« less

Grayscale imbalance correction in real-time phase measuring profilometry

NASA Astrophysics Data System (ADS)

Zhu, Lin; Cao, Yiping; He, Dawu; Chen, Cheng

2016-10-01

Grayscale imbalance correction in real-time phase measuring profilometry (RPMP) is proposed. In the RPMP, the sufficient information is obtained to reconstruct the 3D shape of the measured object in one over twenty-four of a second. Only one color fringe pattern whose R, G and B channels are coded as three sinusoidal phase-shifting gratings with an equivalent shifting phase of 2π/3 is sent to a flash memory on a specialized digital light projector (SDLP). And then the SDLP projects the fringe patterns in R, G and B channels sequentially onto the measured object in one over seventy-two of a second and meanwhile a monochrome CCD camera captures the corresponding deformed patterns synchronously with the SDLP. Because the deformed patterns from three color channels are captured at different time, the color crosstalk is avoided completely. But due to the monochrome CCD camera's different spectral sensitivity to R, G and B tricolor, there will be grayscale imbalance among these deformed patterns captured at R, G and B channels respectively which may result in increasing measuring errors or even failing to reconstruct the 3D shape. So a new grayscale imbalance correction method based on least square method is developed. The experimental results verify the feasibility of the proposed method.

Effects of Host-rock Fracturing on Elastic-deformation Source Models of Volcano Deflation.

PubMed

Holohan, Eoghan P; Sudhaus, Henriette; Walter, Thomas R; Schöpfer, Martin P J; Walsh, John J

2017-09-08

Volcanoes commonly inflate or deflate during episodes of unrest or eruption. Continuum mechanics models that assume linear elastic deformation of the Earth's crust are routinely used to invert the observed ground motions. The source(s) of deformation in such models are generally interpreted in terms of magma bodies or pathways, and thus form a basis for hazard assessment and mitigation. Using discontinuum mechanics models, we show how host-rock fracturing (i.e. non-elastic deformation) during drainage of a magma body can progressively change the shape and depth of an elastic-deformation source. We argue that this effect explains the marked spatio-temporal changes in source model attributes inferred for the March-April 2007 eruption of Piton de la Fournaise volcano, La Reunion. We find that pronounced deflation-related host-rock fracturing can: (1) yield inclined source model geometries for a horizontal magma body; (2) cause significant upward migration of an elastic-deformation source, leading to underestimation of the true magma body depth and potentially to a misinterpretation of ascending magma; and (3) at least partly explain underestimation by elastic-deformation sources of changes in sub-surface magma volume.

Aerial multi-camera systems: Accuracy and block triangulation issues

NASA Astrophysics Data System (ADS)

Rupnik, Ewelina; Nex, Francesco; Toschi, Isabella; Remondino, Fabio

2015-03-01

Oblique photography has reached its maturity and has now been adopted for several applications. The number and variety of multi-camera oblique platforms available on the market is continuously growing. So far, few attempts have been made to study the influence of the additional cameras on the behaviour of the image block and comprehensive revisions to existing flight patterns are yet to be formulated. This paper looks into the precision and accuracy of 3D points triangulated from diverse multi-camera oblique platforms. Its coverage is divided into simulated and real case studies. Within the simulations, different imaging platform parameters and flight patterns are varied, reflecting both current market offerings and common flight practices. Attention is paid to the aspect of completeness in terms of dense matching algorithms and 3D city modelling - the most promising application of such systems. The experimental part demonstrates the behaviour of two oblique imaging platforms in real-world conditions. A number of Ground Control Point (GCP) configurations are adopted in order to point out the sensitivity of tested imaging networks and arising block deformations. To stress the contribution of slanted views, all scenarios are compared against a scenario in which exclusively nadir images are used for evaluation.

Combined use of remote sensing and seismic observations to infer geologically recent crustal deformation, active faulting, and stress fields. [California and Pennsylvania

NASA Technical Reports Server (NTRS)

Alexander, S. S. (Principal Investigator)

1982-01-01

Characteristic traits for earthquakes associated with strike-slip motion in Central California and the Salton Sea area, as revealed in ground based studies and LANDSAT imagery, were compared. The mapped lineaments are found to be oriented in several dominant directions. One direction is the same as the trend of the San Andreas fault. The other directions differ from area to area and may reflect the stresses of earlier geologic processes. The pattern of lineament orientations is significantly LANDSAT MSS data, SEASAT synthetic aperture radar data, and magnetic field data from the South Mountain area west of Gettysburg, Pennsylvania were registered to match each other in spatial position and merged. Pattern recognition techniques were applied to the composite data set to determine its utility in recognizing different rock types and structures in vegetated terrain around South Mountain. With the use of a texture algorithm to enhance geologic features, a classification of the entire area was made. A test of the correlation between SAR tone and texture, LANDSAT tone and texture, and magnetic field data revealed no tone or texture measures linking any two of the original data sets.

M1 excitation in Sm isotopes and the proton-neutron sdg interacting boson model

NASA Astrophysics Data System (ADS)

Mizusaki, Takahiro; Otsuka, Takaharu; Sugita, Michiaki

1991-10-01

The magnetic-dipole scissors mode in spherical to deformed Sm isotopes is studied in terms of the proton-neutron sdg interacting boson model, providing a good agreement with recent experiment by Ziegler et al. The present calculation correctly reproduces the increase of M1 excitation strength in going from spherical to deformed nuclei. It is suggested that there may be 1+ states which do not correspond to the scissors mode but absorb certain M1 strength from the ground state.

Influence of continuous deformations and tremors of rock mass on a building. Case study

NASA Astrophysics Data System (ADS)

Strzałkowski, Piotr

2018-04-01

This work presents an exemplary analysis of the influence of mining exploitations on a building. Continuous deformations of the ground surface in the location of the object were considered. Analysis of the impact of tremors of rock mass on the object was performed. The results of calculations as well as the measurements of surface vibrations accelerations were taken into account. The performed analyses show the influence of a fault on increase of vibrations accelerations.

Finite Element Modeling of Passive Material Influence on the Deformation and Force Output of Skeletal Muscle

PubMed Central

Hodgson, John A.; Chi, Sheng-Wei; Yang, Judy P.; Chen, Jiun-Shyan; Edgerton, V. Reggie; Sinha, Shantanu

2014-01-01

The pattern of deformation of the different structural components of a muscle-tendon complex when it is activated provides important information about the internal mechanics of the muscle. Recent experimental observations of deformations in contracting muscle have presented inconsistencies with current widely held assumption about muscle behavior. These include negative strain in aponeuroses, non-uniform strain changes in sarcomeres, even of individual muscle fibers and evidence that muscle fiber cross sectional deformations are asymmetrical suggesting a need to readjust current models of contracting muscle. We report here our use of finite element modeling techniques to simulate a simple muscle-tendon complex and investigate the influence of passive intramuscular material properties upon the deformation patterns under isometric and shortening conditions. While phenomenological force-displacement relationships described the muscle fiber properties, the material properties of the passive matrix were varied to simulate a hydrostatic model, compliant and stiff isotropically hyperelastic models and an anisotropic elastic model. The numerical results demonstrate that passive elastic material properties significantly influence the magnitude, heterogeneity and distribution pattern of many measures of deformation in a contracting muscle. Measures included aponeurosis strain, aponeurosis separation, muscle fiber strain and fiber cross-sectional deformation. The force output of our simulations was strongly influenced by passive material properties, changing by as much as ~80% under some conditions. Maximum output was accomplished by introducing anisotropy along axes which were not strained significantly during a muscle length change, suggesting that correct costamere orientation may be a critical factor in optimal muscle function. Such a model not only fits known physiological data, but also maintains the relatively constant aponeurosis separation observed during in vivo muscle contractions and is easily extrapolated from our plane-strain conditions into a 3-dimensional structure. Such modeling approaches have the potential of explaining the reduction of force output consequent to changes in material properties of intramuscular materials arising in the diseased state such as in genetic disorders. PMID:22498294

Reactivation versus reworking of the active continental margin during the Zagros collision: Mahallat-Muteh-Laybid complexes, Sanandaj-Sirjan zone, Iran

NASA Astrophysics Data System (ADS)

Aflaki, Mahtab; Shabanian, Esmaeil; Davoodi, Zeinab; Mohajjel, Mohammad

2017-06-01

Reactivation of long-lived basement faults has significant influences on further deformation of collision zones. Three major inherited pre-collisional NW-, N- and NE-trending basement discontinuities have played important roles on the structural and tectono-sedimentary evolution of the Iranian micro-continent in the northeastern part of the Gondwana super-continent. Sanandaj-Sirjan zone (SSZ), known as the metamorphic belt of the Zagros orogeny, marks the SW margin of the Central Iran. SSZ is formed as a result of the Arabia-Eurasia collision and its general trend of deformation coincides with the NW structural trend of the collision. The NE-trending Mahallat, Muteh and Laybid complexes in the middle part of the NW-trending SSZ are the exception and have a trend almost normal to the NW-trending Zagros. A combined methodology of remote sensing, geometric and kinematics analyses complemented by field work was used to reconstruct the history of deformation in the Zagros hinterland since the earlier stages of collision to the present-day. Our results reveal the key role of the preexisting discontinuities of the Iranian basement in both the kinematics and structural pattern of the middle part of the SSZ. These basement faults have acted as main boundary conditions changing the collisional fabric perpendicular to its overall trend. Progressive deformation and the related changes during collision have caused drastic changes in the kinematics of the boundary faults. The establishment of dextral transtension in the SSZ has had secondary influences on the pattern of deformation by local clockwise rotation and localized dextral shear in the southern parts of the area of interest. This study highlights the significance of long-lived pre-existing structures in the deformation of collision zones. Such basement faults are capable to change both the pattern and kinematics of deformation of the adjacent areas involved in a continental collision.

Finite element modeling of passive material influence on the deformation and force output of skeletal muscle.

PubMed

Hodgson, John A; Chi, Sheng-Wei; Yang, Judy P; Chen, Jiun-Shyan; Edgerton, Victor R; Sinha, Shantanu

2012-05-01

The pattern of deformation of different structural components of a muscle-tendon complex when it is activated provides important information about the internal mechanics of the muscle. Recent experimental observations of deformations in contracting muscle have presented inconsistencies with current widely held assumption about muscle behavior. These include negative strain in aponeuroses, non-uniform strain changes in sarcomeres, even of individual muscle fibers and evidence that muscle fiber cross sectional deformations are asymmetrical suggesting a need to readjust current models of contracting muscle. We report here our use of finite element modeling techniques to simulate a simple muscle-tendon complex and investigate the influence of passive intramuscular material properties upon the deformation patterns under isometric and shortening conditions. While phenomenological force-displacement relationships described the muscle fiber properties, the material properties of the passive matrix were varied to simulate a hydrostatic model, compliant and stiff isotropically hyperelastic models and an anisotropic elastic model. The numerical results demonstrate that passive elastic material properties significantly influence the magnitude, heterogeneity and distribution pattern of many measures of deformation in a contracting muscle. Measures included aponeurosis strain, aponeurosis separation, muscle fiber strain and fiber cross-sectional deformation. The force output of our simulations was strongly influenced by passive material properties, changing by as much as ~80% under some conditions. The maximum output was accomplished by introducing anisotropy along axes which were not strained significantly during a muscle length change, suggesting that correct costamere orientation may be a critical factor in the optimal muscle function. Such a model not only fits known physiological data, but also maintains the relatively constant aponeurosis separation observed during in vivo muscle contractions and is easily extrapolated from our plane-strain conditions into a three-dimensional structure. Such modeling approaches have the potential of explaining the reduction of force output consequent to changes in material properties of intramuscular materials arising in the diseased state such as in genetic disorders. Copyright © 2012 Elsevier Ltd. All rights reserved.

Late Neogene deformation of the Chocolate Mountains Anticlinorium: Implications for deposition of the Bouse Formation and early evolution of the Lower Colorado River

USGS Publications Warehouse

Beard, Sue; Haxel, Gordon B.; Dorsey, Rebecca J.; McDougall, Kristin A.; Jacobsen, Carl E.

2016-01-01

Deformation related to late Neogene dextral shear can explain a shift from an estuarine to lacustrine depositional environment in the southern Bouse Formation north of Yuma, Arizona. We infer that late Neogene deformation in the Chocolate Mountain Anticlinorium (CMA) created a barrier that blocked an estuary inlet, and that pre-existing and possibly active structures subsequently controlled the local course of the lower Colorado River. Structural patterns summarized below suggest that the CMA absorbed transpressional strain caused by left-stepping segments of dextral faults of the San Andreas fault system and/or the eastern California shear zone and Gulf of California shear zone. For this hypothesis to be correct, about 200-250 m of post-6 Ma, pre- ~5.3 Ma uplift along the CMA crest would be required to cut off a marine inlet. The 220-km-long CMA, cored by the early Paleogene Orocopia Schist subduction complex, extends from the Orocopia Mountains (Calif.) southeastward through the Chocolate Mountains (parallel to the southern San Andreas fault). Where Highway 78 crosses the Chocolate Mountains (Fig. 1), the CMA turns eastward through the Black Mountain-Picacho area (Calif.) and Trigo Mountains (Ariz.) into southwest Arizona. It separates southernmost Bouse Formation outcrops of the Blythe basin from subsurface Bouse outcrops to the south in the Yuma area. South of Blythe basin the CMA is transected by the lower Colorado River along a circuitous path. Here we focus on the geology of an area between the central Chocolate Mountains and the Yuma Proving Grounds in Arizona. Specific landmarks include the southeast Chocolate Mountains, Midway Mountains, Peter Kane Mountain, Black Mountain, Picacho Peak, and Gavilan Hills. For simplicity, we refer to this as the eastern Chocolate Mountains.

Geomorphic Evidences of Pleistocene Deformations in the Western Pyrenees (France)

NASA Astrophysics Data System (ADS)

Lacan, P.; Nivière, B.; Rousset, D.; Sénéchal, P.

2007-12-01

Due to its intraplate position, the on-going tectonic activity of the Western Pyrenees is only revealed by a moderate and diffuse seismicity. This seismicity presents a general E-W pattern and is distributed along the northern flank of the chain in the western part. We focus here on the Arudy area that suffered from one of the major Pyrenean instrumental earthquakes (M=5,1) in 1980. An early Cretaceous normal fault of the Iberian margin is probably the seismic source of this event. The late Cretaceous inversion of the margin, first in a left-lateral strike-slip mode and then in a more frontal convergence, resulted in a shallow pop-up geometry near Arudy. This pop-up attests of the presence in depth of a crustal discontinuity. The present-day geodynamic arrangement might reactivate this accident in a right lateral mode. This reactivation leads to a strain partitioning between the deep crustal discontinuity and the shallow pop-up that achieved respectively the lateral and frontal components of the displacement. Folding of Quaternary terrace remnants above the thrusts limiting the pop-up, attests of the Pleistocene activity of the structure. Growth of alluvial depocenters in the footwall of these thrusts revealed by near-surface geophysical surveys (electric tomography and ground penetrating radar) attest too of this activity. This deformation resulted in ca 1500 m long and 5-10 m high folds during the middle to late Pleistocene. Using a strain partitioning model, this quantification of the near-surface deformation allows to estimate the displacement achieved by the blind crustal discontinuity. So the seismic hazard due to this fault is better constrained. Project funded by Région Aquitaine and TTI Production.

Retrieval of interseismic displacement from multi-temporal InSAR measurements: challenges and solutions

NASA Astrophysics Data System (ADS)

Zhang, L.; Ding, X.; Lu, Z.; Wen, Y.; Hu, J.

2016-12-01

High-resolution measurements of interseismic displacement are critical for understanding the earthquake cycle and for assessing earthquake hazard. Compared with sparsely located GNSS sites, it is well-known that by jointly analyzing a set of data over the same area acquired on different dates, multi-temporal InSAR (MTInSAR) is capable of remotely imaging interseismic deformation at an unprecedented level of spatial resolution. However conventional MTInSAR cannot hold a considerate promise for the precise retrieval of interseismic deformation in tectonically active zones where complicated atmospheric delay, orbital errors, and localized seasonal ground fluctuations commonly exist. Of interest in this study is to develop reliable solutions to correct or suppress these unwanted signals thereby to improve the accuracy of mapped interseismic displacement. Our technical innovations lie in the following aspects. According to different spatial-temporal characteristics, a joint model that takes both orbit errors and interseismic displacement as parameters is designed to isolate long wavelength motion from orbit error even in the case these two types of signals exhibit similar spatial patterns. To suppress the localized impacts (e.g., a portion of atmospheric artifacts and small-scale anthropogenic deformation), spatial correlation is employed as a constraint during the parameter estimation. The proposed solutions are evaluated by synthetic tests and applied to map the interseismic displacement over Eastern Turkey that spans the Arabia-Eurasia plate boundary zone from a large set of radar images acquired by Envisat/ASAR and Sentinel-1. The derived interseismic displacement validated by GPS data is further used to invert the slip rate and locking depth for the North and East Anatolian Faults. A cross-comparison with published results is also conducted.

Near-Field Deformation Associated with the M6.0 South Napa Earthquake Surface Rupture

NASA Astrophysics Data System (ADS)

Brooks, B. A.; Hudnut, K. W.; Glennie, C. L.; Ericksen, T.

2014-12-01

We characterize near-field deformation associated with the surface rupture of the M6.0 South Napa earthquake from repeat mobile laser scanning (MLS) surveys. Starting the day after the main shock, we operated, sometime simultaneously, short (~75 m range) and medium (~400m range) range laser scanners on a truck or backpack. We scanned most of the length of the principal and secondary surface ruptures at speeds less than 10 km/hr. Scanning occurred primarily in either suburban subdivisions or cultivated vineyards of varying varietals with differing leaf patterns and stages of maturity. Spot-spacing is dense enough (100s of points/m^2) to permit creation of 10-25cm digital elevation models of much of the surface rupture. Scanned features of the right-lateral rupture include classic mole tracks through a variety of soil types, en echelon cracks, offset vine rows, and myriad types of pavement-related deformation. We estimate coseismic surface displacements ranging from 5 to 45 cm by examining offset cultural features and vine rows and by comparing the MLS data with preexisting airborne laser scans from 2003 using point-cloud and solid-modeling methodologies. Additionally, we conducted repeat MLS scans to measure the magnitude and spatial variation of fault afterslip, exceeding 20 cm in some places, particularly in the southern portion of the rupture zone. We anticipate these data sets, in conjunction with independently collected ground-based alinement arrays and space-based geodetic data will contribute significant insight into topics of current debate including assessing the most appropriate material models for shallow fault zones and how shallow and deeper fault slip relate to one another.

Ko Displacement Theory for Structural Shape Predictions

NASA Technical Reports Server (NTRS)

Ko, William L.

2010-01-01

The development of the Ko displacement theory for predictions of structure deformed shapes was motivated in 2003 by the Helios flying wing, which had a 247-ft (75-m) wing span with wingtip deflections reaching 40 ft (12 m). The Helios flying wing failed in midair in June 2003, creating the need to develop new technology to predict in-flight deformed shapes of unmanned aircraft wings for visual display before the ground-based pilots. Any types of strain sensors installed on a structure can only sense the surface strains, but are incapable to sense the overall deformed shapes of structures. After the invention of the Ko displacement theory, predictions of structure deformed shapes could be achieved by feeding the measured surface strains into the Ko displacement transfer functions for the calculations of out-of-plane deflections and cross sectional rotations at multiple locations for mapping out overall deformed shapes of the structures. The new Ko displacement theory combined with a strain-sensing system thus created a revolutionary new structure- shape-sensing technology.

Face Sheet/Core Disbond Growth in Honeycomb Sandwich Panels Subjected to Ground-Air-Ground Pressurization and In-Plane Loading

NASA Technical Reports Server (NTRS)

Chen, Zhi M.; Krueger, Ronald; Rinker, Martin

2015-01-01

Typical damage modes in light honeycomb sandwich structures include face sheet/core disbonding and core fracture, both of which can pose a threat to the structural integrity of a component. These damage modes are of particular interest to aviation certification authorities since several in-service occurrences, such as rudder structural failure and other control surface malfunctions, have been attributed to face sheet/core disbonding. Extensive studies have shown that face sheet/core disbonding and core fracture can lead to damage propagation caused by internal pressure changes in the core. The increasing use of composite sandwich construction in aircraft applications makes it vitally important to understand the effect of ground-air-ground (GAG) cycles and conditions such as maneuver and gust loads on face sheet/core disbonding. The objective of the present study was to use a fracture mechanics based approach developed earlier to evaluate the loading at the disbond front caused by ground-air-ground pressurization and in-plane loading. A honeycomb sandwich panel containing a circular disbond at one face sheet/core interface was modeled with three-dimensional (3D) solid finite elements. The disbond was modeled as a discrete discontinuity and the strain energy release rate along the disbond front was computed using the Virtual Crack Closure Technique (VCCT). Special attention was paid to the pressure-deformation coupling which can decrease the pressure load within the disbonded sandwich section significantly when the structure is highly deformed. The commercial finite element analysis software, Abaqus/Standard, was used for the analyses. The recursive pressure-deformation coupling problem was solved by representing the entrapped air in the honeycomb cells as filled cavities in Abaqus/Standard. The results show that disbond size, face sheet thickness and core thickness are important parameters that determine crack tip loading at the disbond front. Further, the pressure-deformation coupling was found to have an important load decreasing effect [6]. In this paper, a detailed problem description is provided first. Second, the analysis methodology is presented. The fracture mechanics approach used is described and the specifics of the finite element model, including the fluid-filled cavities, are introduced. Third, the initial model verification and validation are discussed. Fourth, the findings from a closely related earlier study [6] are summarized. These findings provided the basis for the current investigation. Fifth, an aircraft ascent scenario from 0 to 12192 m (0 to 40000 ft) is considered and the resulting crack tip loading at the disbond front is determined. In-plane loading to simulate maneuvers and gust conditions are also considered. Sixth, the results are shown for a curved panel, which was used to simulate potential fuselage applications. Finally, a brief summary of observations is presented and recommendations for improvement are provided.

Patterns of postural deformity in non-ambulant people with cerebral palsy: what is the relationship between the direction of scoliosis, direction of pelvic obliquity, direction of windswept hip deformity and side of hip dislocation?

PubMed

Porter, David; Michael, Shona; Kirkwood, Craig

2007-12-01

To investigate: (a) associations between the direction of scoliosis, direction of pelvic obliquity, direction of windswept deformity and side of hip subluxation/ dislocation in non-ambulant people with cerebral palsy; and (b) the lateral distribution of these postural asymmetries. Cross-sectional observational study. Posture management services in three centres in the UK. Non-ambulant people at level five on the gross motor function classification system for cerebral palsy. Direction of pelvic obliquity and lateral spinal curvature determined from physical examination, direction of windswept hip deformity derived from range of hip abduction/adduction, and presence/side of unilateral hip subluxation defined by hip migration percentage. A total of 747 participants were included in the study, aged 6-80 years (median 18 years 10 months). Associations between the direction of scoliosis and direction of pelvic obliquity, and between the direction of windswept hip deformity and side hip subluxation/dislocation were confirmed. A significant association was also seen between the direction of scoliosis and the direction of the windswept hip deformity (P<0.001) such that the convexity of the lateral spinal curve was more likely to be opposite to the direction of windsweeping. Furthermore, significantly more windswept deformities to the right (P=0.007), hips subluxed on the left (P=0.002) and lateral lumbar/lower thoracic spinal curves convex to the left (P=0.03) were observed. The individual asymmetrical postural deformities are not unrelated in terms of direction and not equally distributed to the left/right. A pattern of postural deformity was observed.

Patterns of postural deformity in non-ambulant people with cerebral palsy: what is the relationship between the direction of scoliosis, direction of pelvic obliquity, direction of windswept hip deformity and side of hip dislocation?

PubMed Central

Michael, Shona; Kirkwood, Craig

2008-01-01

Objective: To investigate: (a) associations between the direction of scoliosis, direction of pelvic obliquity, direction of windswept deformity and side of hip subluxation/dislocation in non-ambulant people with cerebral palsy; and (b) the lateral distribution of these postural asymmetries. Design: Cross-sectional observational study. Setting: Posture management services in three centres in the UK. Subjects: Non-ambulant people at level five on the gross motor function classification system for cerebral palsy. Main measures: Direction of pelvic obliquity and lateral spinal curvature determined from physical examination, direction of windswept hip deformity derived from range of hip abduction/adduction, and presence/side of unilateral hip subluxation defined by hip migration percentage. Results: A total of 747 participants were included in the study, aged 6–80 years (median 18 years 10 months). Associations between the direction of scoliosis and direction of pelvic obliquity, and between the direction of windswept hip deformity and side hip subluxation/dislocation were confirmed. A significant association was also seen between the direction of scoliosis and the direction of the windswept hip deformity (P < 0.001) such that the convexity of the lateral spinal curve was more likely to be opposite to the direction of windsweeping. Furthermore, significantly more windswept deformities to the right (P = 0.007), hips subluxed on the left (P = 0.002) and lateral lumbar/lower thoracic spinal curves convex to the left (P = 0.03) were observed. Conclusions: The individual asymmetrical postural deformities are not unrelated in terms of direction and not equally distributed to the left/right. A pattern of postural deformity was observed. PMID:18042604

Structural lineament and pattern analysis of Missouri, using LANDSAT imagery

NASA Technical Reports Server (NTRS)

Martin, J. A.; Kisvarsanyi, G. (Principal Investigator)

1977-01-01

The author has identified the following significant results. Major linear, circular, and arcuate traces were observed on LANDSAT imagery of Missouri. Lineaments plotted within the state boundaries range from 20 to nearly 500 km in length. Several extend into adjoining states. Lineaments plots indicate a distinct pattern and in general reflect structural features of the Precambrian basement of the platform. Coincidence of lineaments traced from the imagery and known structural features in Missouri is high, thus supporting a causative relation between them. The lineament pattern apparently reveals a fundamental style of the deformation of the intracontinental craton. Dozens of heretofore unknown linear features related to epirogenic movements and deformation of this segment of the continental crust were delineated. Lineaments and mineralization are interrelated in a geometrically classifiable pattern.

Adsorbate-induced lattice deformation in IRMOF-74 series

DOE PAGES

Jawahery, Sudi; Simon, Cory M.; Braun, Efrem; ...

2017-01-09

Here, IRMOF-74 analogues are among the most widely studied metal-organic frameworks (MOFs) for adsorption applications because of their one-dimensional channels and high metal density. Most studies involving the IRMOF-74 series assume that the crystal lattice is rigid. This assumption guides the interpretation of experimental data, as changes in the crystal symmetry have so far been ignored as a possibility in the literature. Here, we report a deformation pattern, induced by the adsorption of argon, for IRMOF-74-V. This work has two main implications. First, we use molecular simulations to demonstrate that the IRMOF-74 series undergoes a deformation that is similar tomore » the mechanism behind breathing MOFs, but is unique because the deformation pattern extends beyond a single unit cell of the original structure. Second, we provide an alternative interpretation of experimental small-angle X-ray scattering profiles of these systems, which changes how we view the fundamentals of adsorption in this MOF series.« less

Noninvasive, three-dimensional full-field body sensor for surface deformation monitoring of human body in vivo

NASA Astrophysics Data System (ADS)

Chen, Zhenning; Shao, Xinxing; He, Xiaoyuan; Wu, Jialin; Xu, Xiangyang; Zhang, Jinlin

2017-09-01

Noninvasive, three-dimensional (3-D), full-field surface deformation measurements of the human body are important for biomedical investigations. We proposed a 3-D noninvasive, full-field body sensor based on stereo digital image correlation (stereo-DIC) for surface deformation monitoring of the human body in vivo. First, by applying an improved water-transfer printing (WTP) technique to transfer optimized speckle patterns onto the skin, the body sensor was conveniently and harmlessly fabricated directly onto the human body. Then, stereo-DIC was used to achieve 3-D noncontact and noninvasive surface deformation measurements. The accuracy and efficiency of the proposed body sensor were verified and discussed by considering different complexions. Moreover, the fabrication of speckle patterns on human skin, which has always been considered a challenging problem, was shown to be feasible, effective, and harmless as a result of the improved WTP technique. An application of the proposed stereo-DIC-based body sensor was demonstrated by measuring the pulse wave velocity of human carotid artery.

Airplane wing deformation and flight flutter detection method by using three-dimensional speckle image correlation technology.

PubMed

Wu, Jun; Yu, Zhijing; Wang, Tao; Zhuge, Jingchang; Ji, Yue; Xue, Bin

2017-06-01

Airplane wing deformation is an important element of aerodynamic characteristics, structure design, and fatigue analysis for aircraft manufacturing, as well as a main test content of certification regarding flutter for airplanes. This paper presents a novel real-time detection method for wing deformation and flight flutter detection by using three-dimensional speckle image correlation technology. Speckle patterns whose positions are determined through the vibration characteristic of the aircraft are coated on the wing; then the speckle patterns are imaged by CCD cameras which are mounted inside the aircraft cabin. In order to reduce the computation, a matching technique based on Geodetic Systems Incorporated coded points combined with the classical epipolar constraint is proposed, and a displacement vector map for the aircraft wing can be obtained through comparing the coordinates of speckle points before and after deformation. Finally, verification experiments containing static and dynamic tests by using an aircraft wing model demonstrate the accuracy and effectiveness of the proposed method.

Adsorbate-induced lattice deformation in IRMOF-74 series

PubMed Central

Jawahery, Sudi; Simon, Cory M.; Braun, Efrem; Witman, Matthew; Tiana, Davide; Vlaisavljevich, Bess; Smit, Berend

2017-01-01

IRMOF-74 analogues are among the most widely studied metal-organic frameworks (MOFs) for adsorption applications because of their one-dimensional channels and high metal density. Most studies involving the IRMOF-74 series assume that the crystal lattice is rigid. This assumption guides the interpretation of experimental data, as changes in the crystal symmetry have so far been ignored as a possibility in the literature. Here, we report a deformation pattern, induced by the adsorption of argon, for IRMOF-74-V. This work has two main implications. First, we use molecular simulations to demonstrate that the IRMOF-74 series undergoes a deformation that is similar to the mechanism behind breathing MOFs, but is unique because the deformation pattern extends beyond a single unit cell of the original structure. Second, we provide an alternative interpretation of experimental small-angle X-ray scattering profiles of these systems, which changes how we view the fundamentals of adsorption in this MOF series. PMID:28067222

Adsorbate-induced lattice deformation in IRMOF-74 series

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jawahery, Sudi; Simon, Cory M.; Braun, Efrem

Here, IRMOF-74 analogues are among the most widely studied metal-organic frameworks (MOFs) for adsorption applications because of their one-dimensional channels and high metal density. Most studies involving the IRMOF-74 series assume that the crystal lattice is rigid. This assumption guides the interpretation of experimental data, as changes in the crystal symmetry have so far been ignored as a possibility in the literature. Here, we report a deformation pattern, induced by the adsorption of argon, for IRMOF-74-V. This work has two main implications. First, we use molecular simulations to demonstrate that the IRMOF-74 series undergoes a deformation that is similar tomore » the mechanism behind breathing MOFs, but is unique because the deformation pattern extends beyond a single unit cell of the original structure. Second, we provide an alternative interpretation of experimental small-angle X-ray scattering profiles of these systems, which changes how we view the fundamentals of adsorption in this MOF series.« less

Error estimation of deformable image registration of pulmonary CT scans using convolutional neural networks.

PubMed

Eppenhof, Koen A J; Pluim, Josien P W

2018-04-01

Error estimation in nonlinear medical image registration is a nontrivial problem that is important for validation of registration methods. We propose a supervised method for estimation of registration errors in nonlinear registration of three-dimensional (3-D) images. The method is based on a 3-D convolutional neural network that learns to estimate registration errors from a pair of image patches. By applying the network to patches centered around every voxel, we construct registration error maps. The network is trained using a set of representative images that have been synthetically transformed to construct a set of image pairs with known deformations. The method is evaluated on deformable registrations of inhale-exhale pairs of thoracic CT scans. Using ground truth target registration errors on manually annotated landmarks, we evaluate the method's ability to estimate local registration errors. Estimation of full domain error maps is evaluated using a gold standard approach. The two evaluation approaches show that we can train the network to robustly estimate registration errors in a predetermined range, with subvoxel accuracy. We achieved a root-mean-square deviation of 0.51 mm from gold standard registration errors and of 0.66 mm from ground truth landmark registration errors.

Dislocation evolution in 316 L stainless steel during multiaxial ratchetting deformation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dong Yawei; Kang Guozheng, E-mail: guozhengkang@yahoo.com.cn; Liu Yujie

2012-03-15

Dislocation patterns and their evolutions in 316 L stainless steel during the multiaxial ratchetting deformation were observed by transmission electron microscopy (TEM). The microscopic observations indicate that the dislocation evolution presented during the multiaxial ratchetting with four kinds of multiaxial loading paths is similar to that in the uniaxial case [G. Z. Kang et al., Mater Sci Eng A 527 (2010) 5952]. That is, dislocation networks and dislocation tangles are formed quickly by the multiple-slip and cross-slip of dislocation activated by applied multiaxial stress; and then polarized patterns such as dislocation walls and elongated incipient dislocation cells are formed atmore » the last stage of multiaxial ratchetting. The dislocation patterns evolve more quickly from the modes at low dislocation density to the ones at high density during the multiaxial ratchetting than that in the uniaxial case, and some traces of multiple-slip are observed in the multiaxial ones. The dislocation evolution during the multiaxial ratchetting deformation is summarized by comparing the observed dislocation patterns with those presented in the multiaxial strain-controlled and symmetrical stress-controlled cyclic tests. The multiaxial ratchetting of 316 L stainless steel can be microscopically and qualitatively explained by the observed evolution of dislocation patterns. - Highlights: Black-Right-Pointing-Pointer Dislocation patterns change from lines and nets to tangles, walls and cells. Black-Right-Pointing-Pointer Dislocation patterns evolve quicker in the multiaxial case. Black-Right-Pointing-Pointer Aligned dislocation arrays and some traces of multiple slips are observed. Black-Right-Pointing-Pointer Heterogeneous dislocation patterns result in the multiaxial ratchetting.« less

Infrastructure stability surveillance with high resolution InSAR

NASA Astrophysics Data System (ADS)

Balz, Timo; Düring, Ralf

2017-02-01

The construction of new infrastructure in largely unknown and difficult environments, as it is necessary for the construction of the New Silk Road, can lead to a decreased stability along the construction site, leading to an increase in landslide risk and deformation caused by surface motion. This generally requires a thorough pre-analysis and consecutive surveillance of the deformation patterns to ensure the stability and safety of the infrastructure projects. Interferometric SAR (InSAR) and the derived techniques of multi-baseline InSAR are very powerful tools for a large area observation of surface deformation patterns. With InSAR and deriver techniques, the topographic height and the surface motion can be estimated for large areas, making it an ideal tool for supporting the planning, construction, and safety surveillance of new infrastructure elements in remote areas.

Birefringence and incipient plastic deformation in elastically overdriven [100] CaF2 under shock compression

NASA Astrophysics Data System (ADS)

Li, Y.; Zhou, X. M.; Cai, Y.; Liu, C. L.; Luo, S. N.

2018-04-01

[100] CaF2 single crystals are shock-compressed via symmetric planar impact, and the flyer plate-target interface velocity histories are measured with a laser displacement interferometry. The shock loading is slightly above the Hugoniot elastic limit to investigate incipient plasticity and its kinetics, and its effects on optical properties and deformation inhomogeneity. Fringe patterns demonstrate different features in modulation of fringe amplitude, including birefringence and complicated modulations. The birefringence is attributed to local lattice rotation accompanying incipient plasticity. Spatially resolved measurements show inhomogeneity in deformation, birefringence, and fringe pattern evolutions, most likely caused by the inhomogeneity associated with lattice rotation and dislocation slip. Transiently overdriven elastic states are observed, and the incubation time for incipient plasticity decreases inversely with increasing overdrive by the elastic shock.

Chondron curvature mapping in growth plate cartilage under compressive loading.

PubMed

Vendra, Bhavya B; Roan, Esra; Williams, John L

2018-05-18

The physis, or growth plate, is a layer of cartilage responsible for long bone growth. It is organized into reserve, proliferative and hypertrophic zones. Unlike the reserve zone where chondrocytes are randomly arranged, either singly or in pairs, the proliferative and hypertrophic chondrocytes are arranged within tubular structures called chondrons. In previous studies, the strain patterns within the compressed growth plate have been reported to be nonuniform and inhomogeneous, with an apparent random pattern in compressive strains and a localized appearance of tensile strains. In this study we measured structural deformations along the entire lengths of chondrons when the physis was subjected to physiological (20%) and hyper-physiological (30% and 40%) levels of compression. This provided a means to interpret the apparent random strain patterns seen in texture correlation maps in terms of bending deformations of chondron structures and provided a physical explanation for the inhomogeneous and nonuniform strain patterns reported in previous studies. We observed relatively large bending deformations (kinking) of the chondron structures at the interface of the reserve and proliferative zones during compression. Bending in this region may induce dividing cells to align longitudinally to maintain column formation and drive longitudinal growth. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optical image hiding based on chaotic vibration of deformable moiré grating

NASA Astrophysics Data System (ADS)

Lu, Guangqing; Saunoriene, Loreta; Aleksiene, Sandra; Ragulskis, Minvydas

2018-03-01

Image hiding technique based on chaotic vibration of deformable moiré grating is presented in this paper. The embedded secret digital image is leaked in a form of a pattern of time-averaged moiré fringes when the deformable cover grating vibrates according to a chaotic law of motion with a predefined set of parameters. Computational experiments are used to demonstrate the features and the applicability of the proposed scheme.

Floor-fractured crater models of the Sudbury structure, Canada

NASA Technical Reports Server (NTRS)

Wichman, R. W.; Schultz, P. H.

1992-01-01

The Sudbury structure in Ontario, Canada, is one of the oldest and largest impact structures recognized in the geological record. It is also one of the most extensively deformed and volcanically modified impact structures on Earth. Although few other terrestrial craters are recognized as volcanically modified, numerous impact craters on the Moon have been volcanically and tectonically modified and provide possible analogs for the observed pattern of modification at Sudbury. We correlate the pattern of early deformation at Sudbury to fracture patterns in two alternative lunar analogs and then use these analogs both to estimate the initial size of the Sudbury structure and to model the nature of early crater modification at Sudbury.

Perceiving environmental structure from optical motion

NASA Technical Reports Server (NTRS)

Lappin, Joseph S.

1991-01-01

Generally speaking, one of the most important sources of optical information about environmental structure is known to be the deforming optical patterns produced by the movements of the observer (pilot) or environmental objects. As an observer moves through a rigid environment, the projected optical patterns of environmental objects are systematically transformed according to their orientations and positions in 3D space relative to those of the observer. The detailed characteristics of these deforming optical patterns carry information about the 3D structure of the objects and about their locations and orientations relative to those of the observer. The specific geometrical properties of moving images that may constitute visually detected information about the shapes and locations of environmental objects is examined.

Monitoring of surface deformation in open pit mine using DInSAR time-series: a case study in the N5W iron mine (Carajás, Brazil) using TerraSAR-X data

NASA Astrophysics Data System (ADS)

Mura, José C.; Paradella, Waldir R.; Gama, Fabio F.; Santos, Athos R.; Galo, Mauricio; Camargo, Paulo O.; Silva, Arnaldo Q.; Silva, Guilherme G.

2014-10-01

We present an investigation of surface deformation using Differential SAR Interferometry (DInSAR) time-series carried out in an active open pit iron mine, the N5W, located in the Carajás Mineral Province (Brazilian Amazon region), using 33 TerraSAR-X (TSX-1) scenes. This mine has presented a historical of instability and surface monitoring measurements over sectors of the mine (pit walls) have been done based on ground based radar. Two complementary approaches were used: the standard DInSAR configuration, as an early warning of the slope instability conditions, and the DInSAR timeseries analysis. In order to decrease the topographic phase error a high resolution DEM was generated based on a stereo GeoEye-1 pair. Despite the fact that a DinSAR contains atmospheric and topographic phase artifacts and noise, it was possible to detect deformation in some interferometric pairs, covering pit benches, road ramps and waste piles. The timeseries analysis was performed using the 31 interferometric pairs, which were selected based on the highest mean coherence of a stack of 107 interferograms, presenting less phase unwrapping errors. The time-series deformation was retrieved by the Least-Squares (LS) solution using an extension of the Singular Value Decomposition (SVD), with a set of additional weighted constrain on the acceleration deformation. The atmospheric phase artifacts were filtered in the space-time domain and the DEM height errors were estimated based on the normal baseline diversity. The DInSAR time-series investigation showed good results for monitoring surface displacement in the N5W mine located in a tropical rainforest environment, providing very useful information about the ground movement for alarm, planning and risk assessment.

Thrust faulting and 3D ground deformation of the 3 July 2015 Mw 6.4 Pishan, China earthquake from Sentinel-1A radar interferometry

NASA Astrophysics Data System (ADS)

Sun, Jianbao; Shen, Zheng-Kang; Li, Tao; Chen, Jie

2016-06-01

Boosted by the launch of Sentinel-1A radar satellite from the European Space Agency (ESA), we now have the opportunity of fast, full and multiple coverage of the land based deformation field of earthquakes. Here we use the data to investigate a strong earthquake struck Pishan, western China on July 3, 2015. The earthquake fault is blind and no ground break features are found on-site, thus Synthetic Aperture Radar (SAR) data give full play to its technical advantage for the recovery of coseismic deformation field. By using the Sentinel-1A radar data in the Interferometric Wide Swath mode, we obtain 3 tracks of InSAR data over the struck region, and resolve the 3D ground deformation generated by the earthquake. Then the Line-of-Sight (LOS) InSAR data are inverted for the slip-distribution of the seismogenic fault. The final model shows that the earthquake is completely blind with pure-thrust motion. The maximum slip is 0.48 m at a depth of 7 km, consistent with the depth estimate from seismic reflection data. In particular, the inverted model is also compatible with a south-dipping fault ramp among a group of fault interfaces detected by the seismic reflection profile over the region. The seismic moment obtained equals to a Mw 6.4 earthquake. The Pishan earthquake ruptured the frontal part of the thrust ramps under the Slik anticline, and unloaded the coulomb stress of them. However, it may have loaded stress to the back-thrust above the thrust ramps by 1-4 bar, and promoted it for future failure. Moreover, the stress loading on the west side of the earthquake fault is much larger than that on the east side, indicating a higher risk for failure to the west of the Zepu fault.

TU-F-17A-03: A 4D Lung Phantom for Coupled Registration/Segmentation Evaluation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Markel, D; El Naqa, I; Levesque, I

2014-06-15

Purpose: Coupling the processes of segmentation and registration (regmentation) is a recent development that allows improved efficiency and accuracy for both steps and may improve the clinical feasibility of online adaptive radiotherapy. Presented is a multimodality animal tissue model designed specifically to provide a ground truth to simultaneously evaluate segmentation and registration errors during respiratory motion. Methods: Tumor surrogates were constructed from vacuum sealed hydrated natural sea sponges with catheters used for the injection of PET radiotracer. These contained two compartments allowing for two concentrations of radiotracer mimicking both tumor and background signals. The lungs were inflated to different volumesmore » using an air pump and flow valve and scanned using PET/CT and MRI. Anatomical landmarks were used to evaluate the registration accuracy using an automated bifurcation tracking pipeline for reproducibility. The bifurcation tracking accuracy was assessed using virtual deformations of 2.6 cm, 5.2 cm and 7.8 cm of a CT scan of a corresponding human thorax. Bifurcations were detected in the deformed dataset and compared to known deformation coordinates for 76 points. Results: The bifurcation tracking accuracy was found to have a mean error of −0.94, 0.79 and −0.57 voxels in the left-right, anterior-posterior and inferior-superior axes using a 1×1×5 mm3 resolution after the CT volume was deformed 7.8 cm. The tumor surrogates provided a segmentation ground truth after being registered to the phantom image. Conclusion: A swine lung model in conjunction with vacuum sealed sponges and a bifurcation tracking algorithm is presented that is MRI, PET and CT compatible and anatomically and kinetically realistic. Corresponding software for tracking anatomical landmarks within the phantom shows sub-voxel accuracy. Vacuum sealed sponges provide realistic tumor surrogate with a known boundary. A ground truth with minimal uncertainty is thus realized that can be used for comparing the performance of registration and segmentation algorithms.« less

Detection of Sinkhole Activity in Central Florida with High Spatial-Resolution InSAR Time Series Observations

NASA Astrophysics Data System (ADS)

Oliver-Cabrera, T.; Wdowinski, S.; Kruse, S.

2016-12-01

Central Florida's thick carbonate deposits and hydrological conditions make the area prone to sinkhole development. Sinkhole collapse is a major geologic hazard, threatening human life and causing substantial damage to property. Detecting sinkhole deformation before a collapse is a difficult task, due to small and typically unnoticeable surface changes. Most techniques used to map sinkholes, such as ground penetrating radar, require ground contact and are practical for localized (typically 2D, tens to hundreds of meters) surveys but not for broad study areas. In this study we use Persistent Scatterer (PS) time series analysis of Interferometric Synthetic Aperture Radar (InSAR), which is a very useful technique for detecting localized deformation while covering vast areas. We acquired SAR images over four locations in central Florida in order to detect possible pre-collapse or slow subsidence surface movements. The data used in this study were acquired by TerraSAR-X and COSMO-SkyMed satellites with pixel resolutions ranging between 25cm and 2m. To date, we have obtained four datasets, each of 25-30 acquisitions, covering a period of roughly one year over a total of roughly 2200 km2. We also installed two corner reflectors over a subsiding sinkhole located in an open vegetated area, to provide strong scattering and improve coherence over that particular location. We generate PS time series for each of the four datasets. Preliminary results show localized deformation at several houses and commercial buildings in several locations. Deforming areas vary in size from approximately 10mx20m of a single house to 60mx60m for a commercial building. On site ground penetrating radar surveys will be performed in these areas to verify their relationship to possible sinkhole activities. Our results also confirm that the corner reflectors improved PS detection over low coherence areas.

Constraints on geothermal reservoir volume change calculations from InSAR surface displacements and injection and production data

NASA Astrophysics Data System (ADS)

Kaven, J. Ole; Barbour, Andrew J.; Ali, Tabrez

2017-04-01

Continual production of geothermal energy at times leads to significant surface displacement that can be observed in high spatial resolution using InSAR imagery. The surface displacement can be analyzed to resolve volume change within the reservoir revealing the often-complicated patterns of reservoir deformation. Simple point source models of reservoir deformation in a homogeneous elastic or poro-elastic medium can be superimposed to provide spatially varying, kinematic representations of reservoir deformation. In many cases, injection and production data are known in insufficient detail; but, when these are available, the same Green functions can be used to constrain the reservoir deformation. Here we outline how the injection and production data can be used to constrain bounds on the solution by posing the inversion as a quadratic programming with inequality constraints and regularization rather than a conventional least squares solution with regularization. We apply this method to InSAR-derived surface displacements at the Coso and Salton Sea Geothermal Fields in California, using publically available injection and production data. At both geothermal fields the available surface deformation in conjunction with the injection and production data permit robust solutions for the spatially varying reservoir deformation. The reservoir deformation pattern resulting from the constrained quadratic programming solution is more heterogeneous when compared to a conventional least squares solution. The increased heterogeneity is consistent with the known structural controls on heat and fluid transport in each geothermal reservoir.

Towards forecasting volcanic eruptions on a global scale

NASA Astrophysics Data System (ADS)

Hooper, A. J.; Heimisson, E. R.; Gaddes, M.; Bagnardi, M.; Sigmundsson, F.; Spaans, K.; Parks, M.; Gudmundsson, M. T.; Ebmeier, S. K.; Holohan, E. P.; Wright, T. J.; Jonsdottir, K.; Hreinsdottir, S.; Dumont, S.; Ofeigsson, B.; Vogfjord, K. S.

2016-12-01

Volcanic eruptions can cause loss of life, damage health, and have huge economic impacts, providing strong societal motivation for predicting eruptive behavior prior to and during eruptions. I will present here recent progress we have made in mechanical modelling with a predictive capacity, and how we are expanding volcano monitoring to a global scale. The eruption of Bardarbunga volcano, Iceland, in 2014-2015 was the largest eruption there for more than 200 years, producing 1.6 km3of lava. Prior to eruption, magma propagated almost 50 km beneath the surface, over a period of two weeks. Key questions to answer in advance of such eruptions are: will it erupt, where, how much and for how long? We developed a model based on magma taking a path that maximizes energy release, which aligns well with the actual direction taken. Our model also predicts eruption in a topographic low, as actually occurred. As magma was withdrawn, the volcano surface sagged downwards. A coupled model of magma flow and piston-like collapse predicts a declining magma flow rate and ground subsidence rate, in accordance with that observed. With such a model, observations can be used to predict the timescale and rates of eruption, even before one starts. The primary data needed to constrain these predictive models are measurements of surface deformation. In Iceland, this is achieved using high accuracy GPS, however, most volcanoes have no ground instrumentation. A recent ESA mission, Sentinel-1, can potentially image deformation at almost all subaerial volcanoes every 6 days, using a technique called interferometric synthetic aperture radar (InSAR). This will allow us to detect early stages of magma migration at any volcano, then task other satellites to acquire data at a higher rate. We are working on a system to process all Sentinel-1 data in near-real time, which is a big data challenge. We have also developed new algorithms that maximize signal extraction from each new acquisition and recognize when the deformation pattern at any volcano has changed significantly. There are still challenges to overcome to incude processes occurring within the magma as it moves, cools, crystallizes and exsolves gases. But with this combined approach of global data collection and innovative modelling, we hope to better mitigate the effects of volcanic eruptions going forward.

Surface rupture and slip variation induced by the 2010 El Mayor-Cucapah earthquake, Baja California, quantified using COSI-Corr analysis on pre- and post-earthquake LiDAR acquisitions

NASA Astrophysics Data System (ADS)

Leprince, S.; Hudnut, K. W.; Akciz, S. O.; Hinojosa-Corona, A.; Fletcher, J. M.

2011-12-01

One-hundred and three years after the publication of the Lawson report on the Great 1906 earthquake, accurate documentation of surface deformation along the entire length of an earthquake is still challenging. Analysis of pre- and post-earthquake topographic data provides an opportunity to deliver the full 3D displacement field of the ground's surface. However, direct differencing of a pre- and post-earthquake digital topography model (DEM) generally leads to biased estimation of the vertical component of the deformation. Indeed, if the earthquake also produced significant horizontal motion, or if the pre- and post-earthquake DEM acquisitions exhibit non-negligible horizontal mis-registration, then the vertical offset measured by direct differencing will be biased by the local topography gradient. To overcome this limitation, we use the COSI-Corr sub-pixel correlation algorithm to estimate the relative horizontal offset between the pre- and post- 2010 El Mayor - Cucapah earthquake high resolution LiDAR acquisitions. Compensating for the horizontal offset between the two LiDAR acquisitions allows us to estimate unbiased measurements of the vertical component of the surface fault rupture induced by the El Mayor-Cucapah earthquake. We will also show the limitations of the available data set, such as aircraft jitter artifacts, which impaired accurate measurements of the horizontal component of the surface deformation. This analysis shows an unprecedented view of the complete vertical slip component of the rupture induced by the Mw 7.2 2010 El Mayor-Cucapah earthquake, sampled at every 5 m, over a length of about 100 km, and with a vertical accuracy of a few centimeters. Using sampling bins as narrow as 150 m and 1.5 km long, variations in the vertical component of an oblique slip earthquake are presented, with breaks along multiple fault-strands showing opposite dip directions and diffuse boundaries. With the availability of high precision pre- and post-earthquake data, COSI-Corr has the ability to accurately document the variability of 3D surface slip along strike of an earthquake rupture. Such data can be used to investigate the causes of this variability, and improve our understanding of its influence on the pattern of ground shaking.

Correcting for the effects of pupil discontinuities with the ACAD method

NASA Astrophysics Data System (ADS)

Mazoyer, Johan; Pueyo, Laurent; N'Diaye, Mamadou; Mawet, Dimitri; Soummer, Rémi; Norman, Colin

2016-07-01

The current generation of ground-based coronagraphic instruments uses deformable mirrors to correct for phase errors and to improve contrast levels at small angular separations. Improving these techniques, several space and ground based instruments are currently developed using two deformable mirrors to correct for both phase and amplitude errors. However, as wavefront control techniques improve, more complex telescope pupil geometries (support structures, segmentation) will soon be a limiting factor for these next generation coronagraphic instruments. The technique presented in this proceeding, the Active Correction of Aperture Discontinuities method, is taking advantage of the fact that most future coronagraphic instruments will include two deformable mirrors, and is proposing to find the shapes and actuator movements to correct for the effect introduced by these complex pupil geometries. For any coronagraph previously designed for continuous apertures, this technique allow to obtain similar performance in contrast with a complex aperture (with segmented and secondary mirror support structures), with high throughput and flexibility to adapt to changing pupil geometry (e.g. in case of segment failure or maintenance of the segments). We here present the results of the parametric analysis realized on the WFIRST pupil for which we obtained high contrast levels with several deformable mirror setups (size, separation between them), coronagraphs (Vortex charge 2, vortex charge 4, APLC) and spectral bandwidths. However, because contrast levels and separation are not the only metrics to maximize the scientific return of an instrument, we also included in this study the influence of these deformable mirror shapes on the throughput of the instrument and sensitivity to pointing jitters. Finally, we present results obtained on another potential space based telescope segmented aperture. The main result of this proceeding is that we now obtain comparable performance than the coronagraphs previously designed for WFIRST. First result from the parametric analysis strongly suggest that the 2 deformable mirror set up (size and distance between them) have a important impact on the performance in contrast and throughput of the final instrument.

A rib-specific multimodal registration algorithm for fused unfolded rib visualization using PET/CT

NASA Astrophysics Data System (ADS)

Kaftan, Jens N.; Kopaczka, Marcin; Wimmer, Andreas; Platsch, Günther; Declerck, Jérôme

2014-03-01

Respiratory motion affects the alignment of PET and CT volumes from PET/CT examinations in a non-rigid manner. This becomes particularly apparent if reviewing fine anatomical structures such as ribs when assessing bone metastases, which frequently occur in many advanced cancers. To make this routine diagnostic task more efficient, a fused unfolded rib visualization for 18F-NaF PET/CT is presented. It allows to review the whole rib cage in a single image. This advanced visualization is enabled by a novel rib-specific registration algorithm that rigidly optimizes the local alignment of each individual rib in both modalities based on a matched filter response function. More specifically, rib centerlines are automatically extracted from CT and subsequently individually aligned to the corresponding bone-specific PET rib uptake pattern. The proposed method has been validated on 20 PET/CT scans acquired at different clinical sites. It has been demonstrated that the presented rib- specific registration method significantly improves the rib alignment without having to run complex deformable registration algorithms. At the same time, it guarantees that rib lesions are not further deformed, which may otherwise affect quantitative measurements such as SUVs. Considering clinically relevant distance thresholds, the centerline portion with good alignment compared to the ground truth improved from 60:6% to 86:7% after registration while approximately 98% can be still considered as acceptably aligned.