Analytical design and evaluation of an active control system for helicopter vibration reduction and gust response alleviation

NASA Technical Reports Server (NTRS)

Taylor, R. B.; Zwicke, P. E.; Gold, P.; Miao, W.

1980-01-01

An analytical study was conducted to define the basic configuration of an active control system for helicopter vibration and gust response alleviation. The study culminated in a control system design which has two separate systems: narrow band loop for vibration reduction and wider band loop for gust response alleviation. The narrow band vibration loop utilizes the standard swashplate control configuration to input controller for the vibration loop is based on adaptive optimal control theory and is designed to adapt to any flight condition including maneuvers and transients. The prime characteristics of the vibration control system is its real time capability. The gust alleviation control system studied consists of optimal sampled data feedback gains together with an optimal one-step-ahead prediction. The prediction permits the estimation of the gust disturbance which can then be used to minimize the gust effects on the helicopter.

Single Airfoil Gust Response Problem: Category 3, Problem 1

NASA Technical Reports Server (NTRS)

Scott, James R.

2004-01-01

An unsteady aerodynamic code, called GUST3D (ref. 3), has been developed to solve equation (8) for flows with periodic vortical disturbances. The code uses a frequency-domain approach with second-order central differences and a pressure radiation condition in the far field. GUST3D requires as input certain mean flow quantities which are calculated separately by a potential flow solver. The solver calculates the mean ow using a Gothert's Rule approximation (ref. 3). On the airfoil surface, it uses the solution calculated by the potential code FLO36 (ref. 4). Figures 1-2 show the mean pressure along the airfoil surface for the two airfoil geometries. In Figures 3 - 8, we present the RMS pressure on the airfoil surface. Each figure shows three GUST3D solutions (calculated on grids with different far-field boundary locations). Three solutions are shown to provide some indication of the numerical uncertainty in the results. Figures 9 - 13 present the acoustic intensity. We again show three solutions per case. Note that no results are presented for the k1 = k2 = 2.0 loaded airfoil case, as an acceptable solution could not be obtained. A few comments need to be made about the results shown. First, since the last Workshop, the GUST3D code has been substantially upgraded. This includes implementing a more accurate far-field boundary condition (ref. 5) and developing improved gridding capabilities. This is the reason for any differences that may exist between the present results and results from the last Workshop. Second, the intensity results on the circle R = 4C were obtained using a Kirchoff method (ref. 6). The Kirchoff surface was the circle R = 2C. Finally, the GUST3D code is most accurate for low reduced frequencies. A new domain decomposition approach (ref. 7) has been developed to improve accuracy. Both the single domain and domain decomposition approaches were used in generating the present results.

Turbulence Hazard Metric Based on Peak Accelerations for Jetliner Passengers

NASA Technical Reports Server (NTRS)

Stewart, Eric C.

2005-01-01

Calculations are made of the approximate hazard due to peak normal accelerations of an airplane flying through a simulated vertical wind field associated with a convective frontal system. The calculations are based on a hazard metric developed from a systematic application of a generic math model to 1-cosine discrete gusts of various amplitudes and gust lengths. The math model simulates the three degree-of- freedom longitudinal rigid body motion to vertical gusts and includes (1) fuselage flexibility, (2) the lag in the downwash from the wing to the tail, (3) gradual lift effects, (4) a simplified autopilot, and (5) motion of an unrestrained passenger in the rear cabin. Airplane and passenger response contours are calculated for a matrix of gust amplitudes and gust lengths. The airplane response contours are used to develop an approximate hazard metric of peak normal accelerations as a function of gust amplitude and gust length. The hazard metric is then applied to a two-dimensional simulated vertical wind field of a convective frontal system. The variations of the hazard metric with gust length and airplane heading are demonstrated.

A Study of Airline Passenger Susceptibility to Atmospheric Turbulence Hazard

NASA Technical Reports Server (NTRS)

Stewart, Eric C.

2000-01-01

A simple, generic, simulation math model of a commercial airliner has been developed to study the susceptibility of unrestrained passengers to large, discrete gust encounters. The math model simulates the longitudinal motion to vertical gusts and includes (1) motion of an unrestrained passenger in the rear cabin, (2) fuselage flexibility, (3) the lag in the downwash from the wing to the tail, and (4) unsteady lift effects. Airplane and passenger response contours are calculated for a matrix of gust amplitudes and gust lengths of a simulated mountain rotor. A comparison of the model-predicted responses to data from three accidents indicates that the accelerations in actual accidents are sometimes much larger than the simulated gust encounters.

Helicopter gust response characteristics including unsteady aerodynamic stall effects

NASA Technical Reports Server (NTRS)

Arcidiacono, P. J.; Bergquist, R. R.; Alexander, W. T., Jr.

1974-01-01

The results of an analytical study to evaluate the general response characteristics of a helicopter subjected to various types of discrete gust encounters are presented. The analysis employed was a nonlinear coupled, multi-blade rotorfuselage analysis including the effects of blade flexibility and unsteady aerodynamic stall. Only the controls-fixed response of the basic aircraft without any aircraft stability augmentation was considered. A discussion of the basic differences between gust sensitivity of fixed and rotary wing aircraft is presented. The effects of several rotor configuration and aircraft operating parameters on initial gust-induced load factor and blade vibratory stress and pushrod loads are discussed.

Measurement of Gust Response on a Turbine Cascade

NASA Technical Reports Server (NTRS)

Kurkov, A. P.; Lucci, B. L.

1995-01-01

The paper presents benchmark experimental data on a gust response of an annular turbine cascade. The experiment was particularly designed to provide data for comparison with the results of a typical linearized gust-response analysis. Reduced frequency, Mach number, and incidence were varied independently. Except for the lowest reduced frequency, the gust velocity distribution was nearly sinusoidal. For the high inlet-velocity series of tests, the cascade was near choking. The mean flow was documented by measuring blade surface pressures and the cascade exit flow. High-response pressure transducers were used to measure the unsteady pressure distribution. Inlet-velocity components and turbulence parameters were measured using hot wire. In addition to the synchronous time-average pressure spectra, typical power spectra are included for several representative conditions.

The application of the statistical theory of extreme values to gust-load problems

NASA Technical Reports Server (NTRS)

Press, Harry

1950-01-01

An analysis is presented which indicates that the statistical theory of extreme values is applicable to the problems of predicting the frequency of encountering the larger gust loads and gust velocities for both specific test conditions as well as commercial transport operations. The extreme-value theory provides an analytic form for the distributions of maximum values of gust load and velocity. Methods of fitting the distribution are given along with a method of estimating the reliability of the predictions. The theory of extreme values is applied to available load data from commercial transport operations. The results indicate that the estimates of the frequency of encountering the larger loads are more consistent with the data and more reliable than those obtained in previous analyses. (author)

Structural response to discrete and continuous gusts of an airplane having wing bending flexibility and a correlation of calculated and flight results

NASA Technical Reports Server (NTRS)

Houbolt, John C; Kordes, Eldon E

1954-01-01

An analysis is made of the structural response to gusts of an airplane having the degrees of freedom of vertical motion and wing bending flexibility and basic parameters are established. A convenient and accurate numerical solution of the response equations is developed for the case of discrete-gust encounter, an exact solution is made for the simpler case of continuous-sinusoidal-gust encounter, and the procedure is outlined for treating the more realistic condition of continuous random atmospheric turbulence, based on the methods of generalized harmonic analysis. Correlation studies between flight and calculated results are then given to evaluate the influence of wing bending flexibility on the structural response to gusts of two twin-engine transports and one four-engine bomber. It is shown that calculated results obtained by means of a discrete-gust approach reveal the general nature of the flexibility effects and lead to qualitative correlation with flight results. In contrast, calculations by means of the continuous-turbulence approach show good quantitative correlation with flight results and indicate a much greater degree of resolution of the flexibility effects.

Dynamic wind-tunnel tests of an aeromechanical gust-alleviation system using several different combinations of control surfaces

NASA Technical Reports Server (NTRS)

Stewart, E. C.; Doggett, R. V., Jr.

1978-01-01

Some experimental results are presented from wind tunnel studies of a dynamic model equipped with an aeromechanical gust alleviation system for reducing the normal acceleration response of light airplanes. The gust alleviation system consists of two auxiliary aerodynamic surfaces that deflect the wing flaps through mechanical linkages when a gust is encountered to maintain nearly constant airplane lift. The gust alleviation system was implemented on a 1/6-scale, rod mounted, free flying model that is geometrically and dynamically representative of small, four place, high wing, single engine, light airplanes. The effects of flaps with different spans, two size of auxiliary aerodynamic surfaces, plain and double hinged flaps, and a flap elevator interconnection were studied. The model test results are presented in terms of predicted root mean square response of the full scale airplane to atmospheric turbulence. The results show that the gust alleviation system reduces the root mean square normal acceleration response by 30 percent in comparison with the response in the flaps locked condition. Small reductions in pitch-rate response were also obtained. It is believed that substantially larger reductions in normal acceleration can be achieved by reducing the rather high levels of mechanical friction which were extant in the alleviation system of the present model.

Two-dimensional unsteady lift problems in supersonic flight

NASA Technical Reports Server (NTRS)

Heaslet, Max A; Lomax, Harvard

1949-01-01

The variation of pressure distribution is calculated for a two-dimensional supersonic airfoil either experiencing a sudden angle-of-attack change or entering a sharp-edge gust. From these pressure distributions the indicial lift functions applicable to unsteady lift problems are determined for two cases. Results are presented which permit the determination of maximum increment in lift coefficient attained by an unrestrained airfoil during its flight through a gust. As an application of these results, the minimum altitude for safe flight through a specific gust is calculated for a particular supersonic wing of given strength and wing loading.

Discrete Gust Model for Launch Vehicle Assessments

NASA Technical Reports Server (NTRS)

Leahy, Frank B.

2008-01-01

Analysis of spacecraft vehicle responses to atmospheric wind gusts during flight is important in the establishment of vehicle design structural requirements and operational capability. Typically, wind gust models can be either a spectral type determined by a random process having a wide range of wavelengths, or a discrete type having a single gust of predetermined magnitude and shape. Classical discrete models used by NASA during the Apollo and Space Shuttle Programs included a 9 m/sec quasi-square-wave gust with variable wavelength from 60 to 300 m. A later study derived discrete gust from a military specification (MIL-SPEC) document that used a "1-cosine" shape. The MIL-SPEC document contains a curve of non-dimensional gust magnitude as a function of non-dimensional gust half-wavelength based on the Dryden spectral model, but fails to list the equation necessary to reproduce the curve. Therefore, previous studies could only estimate a value of gust magnitude from the curve, or attempt to fit a function to it. This paper presents the development of the MIL-SPEC curve, and provides the necessary information to calculate discrete gust magnitudes as a function of both gust half-wavelength and the desired probability level of exceeding a specified gust magnitude.

Special effects of gust loads on military aircraft

NASA Technical Reports Server (NTRS)

Houbolt, John C.

1994-01-01

In the operation of airplanes, atmospheric turbulence creates a broad spectrum of problems. The nature of these problems is presented in this paper. Those that are common to both the commercial carriers and to the military fleet are discussed first. Attention is then focused on the problems that are of special concern in military operations. An aim is to bring out the need for continued effort in the gust research area.

Calculation of wing response to gusts and blast waves with vortex lift effect

NASA Technical Reports Server (NTRS)

Chao, D. C.; Lan, C. E.

1983-01-01

A numerical study of the response of aircraft wings to atmospheric gusts and to nuclear explosions when flying at subsonic speeds is presented. The method is based upon unsteady quasi-vortex lattice method, unsteady suction analogy and Pade approximant. The calculated results, showing vortex lag effect, yield reasonable agreement with experimental data for incremental lift on wings in gust penetration and due to nuclear blast waves.

Experimental and analytical study on the flutter and gust response characteristics of a torsion-free-wing airplane model. [in the Langley transonic dynamics tunnel

NASA Technical Reports Server (NTRS)

Murphy, A. C.

1981-01-01

Experimental data and correlative analytical results on the flutter and gust response characteristics of a torsion-free-wing (TFW) fighter airplane model are presented. TFW consists of a combined wing/boom/canard surface and was tested with the TFW free to pivot in pitch and with the TFW locked to the fuselage. Flutter and gust response characteristics were measured in the Langley Transonic Dynamics Tunnel with the complete airplane model mounted on a cable mount system that provided a near free flying condition. Although the lowest flutter dynamic pressure was measured for the wing free configuration, it was only about 20 deg less than that for the wing locked configuration. However, no appreciable alleviation of the gust response was measured by freeing the wing.

Forcing function modeling for flow induced vibration

NASA Technical Reports Server (NTRS)

Fleeter, Sanford

1993-01-01

The fundamental forcing function unsteady aerodynamics for application to turbomachine blade row forced response are considered, accomplished through a series of experiments performed in a rotating annular cascade and a research axial flow turbine. In particular, the unsteady periodic flowfields downstream of rotating rows of perforated plates, airfoils and turbine blade rows are measured with a cross hot-wire and an unsteady total pressure probe. The unsteady velocity and static pressure fields were then analyzed harmonically and split into vortical and potential gusts, accomplished by developing a gust splitting analysis which includes both gust unsteady static pressure and velocity data. The perforated plate gusts closely were found to be linear theory vortical gusts, satisfying the vortical gust constraints. The airfoil and turbine blade row generated velocity perturbations did not satisfy the vortical gust constraints. However, the decomposition of the unsteady flow field separated the data into a propagating vortical component which satisfied these vortical gust constraints and a decaying potential component.

A study of helicopter gust response alleviation by automatic control

NASA Technical Reports Server (NTRS)

Saito, S.

1983-01-01

Two control schemes designed to alleviate gust-induced vibration are analytically investigated for a helicopter with four articulated blades. One is an individual blade pitch control scheme. The other is an adaptive blade pitch control algorithm based on linear optimal control theory. In both controllers, control inputs to alleviate gust response are superimposed on the conventional control inputs required to maintain the trim condition. A sinusoidal vertical gust model and a step gust model are used. The individual blade pitch control, in this research, is composed of sensors and a pitch control actuator for each blade. Each sensor can detect flapwise (or lead-lag or torsionwise) deflection of the respective blade. The acturator controls the blade pitch angle for gust alleviation. Theoretical calculations to predict the performance of this feedback system have been conducted by means of the harmonic method. The adaptive blade pitch control system is composed of a set of measurements (oscillatory hub forces and moments), an identification system using a Kalman filter, and a control system based on the minimization of the quadratic performance function.

A Summary of Revisions Applied to a Turbulence Response Analysis Method for Flexible Aircraft Configurations

NASA Technical Reports Server (NTRS)

Funk, Christie J.; Perry, Boyd, III; Silva, Walter A.; Newman, Brett

2014-01-01

A software program and associated methodology to study gust loading on aircraft exists for a classification of geometrically simplified flexible configurations. This program consists of a simple aircraft response model with two rigid and three flexible symmetric degrees-of - freedom and allows for the calculation of various airplane responses due to a discrete one-minus- cosine gust as well as continuous turbulence. Simplifications, assumptions, and opportunities for potential improvements pertaining to the existing software program are first identified, then a revised version of the original software tool is developed with improved methodology to include more complex geometries, additional excitation cases, and additional output data so as to provide a more useful and precise tool for gust load analysis. In order to improve the original software program to enhance usefulness, a wing control surface and horizontal tail control surface is added, an extended application of the discrete one-minus-cosine gust input is employed, a supplemental continuous turbulence spectrum is implemented, and a capability to animate the total vehicle deformation response to gust inputs is included. These revisions and enhancements are implemented and an analysis of the results is used to validate the modifications.

Gust Response Analysis of a Turbine Cascade

NASA Technical Reports Server (NTRS)

Gorla, R. S. R.; Reddy, T. S. R.; Reddy, D. R.; Kurkov, A. P.

2001-01-01

A study was made of the gust response of an annular turbine cascade using a two-dimensional Navier Stokes code. The time-marching CFD code, NPARC, was used to calculate the unsteady forces due to the fluid flow. The computational results were compared with a previously published experimental data for the annular cascade reported in the literature. Reduced frequency, Mach number and angle of incidence were varied independently and the gust velocity was sinusoidal. For the high inlet velocity case, the cascade was nearly choked.

Passive Gust Alleviation for a Flying Wing Aircraft

DTIC Science & Technology

2013-01-10

250 Poisson ratio - 0.3 Density g/cm 3 ρ 1.57 Ply thickness mm t 0.131 Fibre volume % Vf 57.7 Once the material was chosen, the initial...high aspect ratio in flying wing configuration. It is aimed at minimizing the gust response of the aircraft by using the PGAD integrated at the wing... ratio in flying wing configuration. It is aimed at minimizing the gust response of the aircraft by using the PGAD integrated at the wing tip. The

An Investigation of the Overlap Between the Statistical Discrete Gust and the Power Spectral Density Analysis Methods

NASA Technical Reports Server (NTRS)

Perry, Boyd, III; Pototzky, Anthony S.; Woods, Jessica A.

1989-01-01

The results of a NASA investigation of a claimed Overlap between two gust response analysis methods: the Statistical Discrete Gust (SDG) Method and the Power Spectral Density (PSD) Method are presented. The claim is that the ratio of an SDG response to the corresponding PSD response is 10.4. Analytical results presented for several different airplanes at several different flight conditions indicate that such an Overlap does appear to exist. However, the claim was not met precisely: a scatter of up to about 10 percent about the 10.4 factor can be expected.

Propagation and scattering of acoustic-vorticity waves in annular swirling flows

NASA Astrophysics Data System (ADS)

Golubev, Vladimir Viktorovich

1997-08-01

The dissertation presents a fundamental extension of unsteady aerodynamic theory developed to predict fluctuating forces on aircraft structural components. These excitations may result from a variety of upstream flow non-uniformities such as atmospheric turbulence, airframe tip vortices and wakes, engine inlet distortions and secondary flows. In the frame of reference of a downstream aircraft component, an upstream flow non- uniformity appears as a propagating vorticity wave (a gust). Classical treatment of gust interaction problems developed for uniform, potential upstream mean flows is based on the fact that it is possible to consider separately incident or scattered acoustic, entropic and vortical modes of unsteady flow motion. A purely vortical gust remains 'frozen' as it convects with the flow. The coupling between different unsteady components may occur only at the surface of a solid structure, or in the close vicinity of a lifting body. The classical approach, however, is not justified for an aircraft engine system where the internal turbomachinery flow is non-uniform and non-potential as it exhibits a strong swirling motion. In such a flow, acting centrifugal and Coriolis forces couple the various unsteady modes which thus can no longer be determined independently of each other. The new developed theory follows the decomposition of unsteady velocity field into vortical and potential components. In spite of the modal coupling, this decomposition elucidates the physical phenomena associated with unsteady swirling motion by indicating the degree of interaction between the various modes. It paves the way for generalizing the classical definition of a gust for vortical swirling flows. The concept of a generalized gust is developed based on the eigenmode pseudospectral analysis of the coupled equations of unsteady swirling motion. This analysis reveals two distinct regions of eigenvalues corresponding to pressure-dominated nearly-sonic and vorticity- dominated nearly-convected eigenmodes. A compact discrete spectrum of nearly-convected eigenvalues clusters with infinitely increasing density approaching an accumulation convected critical layer. The generalized gust is then identified with the nearly-convected eigenspectrum and formulated in terms of a non-amplifying nearly-convected wave and an instability wave growing in the critical layer. Based on the generalized gust model, a boundary-value problem of unsteady three-dimensional acoustic-vorticity waves propagating in a vortical swirling flow and impinging on a turbomachinery blading is formulated and solved numerically. A set of benchmark results reveals a significant effect of swirling flow motion on aerodynamic and acoustic response of the annular cascade.

An investigation of the 'Overlap' between the Statistical-Discrete-Gust and the Power-Spectral-Density analysis methods

NASA Technical Reports Server (NTRS)

Perry, Boyd, III; Pototzky, Anthony S.; Woods, Jessica A.

1989-01-01

This paper presents the results of a NASA investigation of a claimed 'Overlap' between two gust response analysis methods: the Statistical Discrete Gust (SDG) method and the Power Spectral Density (PSD) method. The claim is that the ratio of an SDG response to the corresponding PSD response is 10.4. Analytical results presented in this paper for several different airplanes at several different flight conditions indicate that such an 'Overlap' does appear to exist. However, the claim was not met precisely: a scatter of up to about 10 percent about the 10.4 factor can be expected.

An Overview of Modifications Applied to a Turbulence Response Analysis Method for Flexible Aircraft Configurations

NASA Technical Reports Server (NTRS)

Funk, Christie J.

2013-01-01

A software program and associated methodology to study gust loading on aircraft exists for a classification of geometrically simplified flexible configurations. This program consists of a simple aircraft response model with two rigid and three flexible symmetric degrees of freedom and allows for the calculation of various airplane responses due to a discrete one-minus-cosine gust as well as continuous turbulence. Simplifications, assumptions, and opportunities for potential improvements pertaining to the existing software program are first identified, then a revised version of the original software tool is developed with improved methodology to include more complex geometries, additional excitation cases, and output data so as to provide a more useful and accurate tool for gust load analysis. Revisions are made in the categories of aircraft geometry, computation of aerodynamic forces and moments, and implementation of horizontal tail mode shapes. In order to improve the original software program to enhance usefulness, a wing control surface and horizontal tail control surface is added, an extended application of the discrete one-minus-cosine gust input is employed, a supplemental continuous turbulence spectrum is implemented, and a capability to animate the total vehicle deformation response to gust inputs in included. These revisions and enhancements are implemented and an analysis of the results is used to validate the modifications.

Influence of vane sweep on rotor-stator interaction noise

NASA Technical Reports Server (NTRS)

Envia, Edmane; Kerschen, Edward J.

1990-01-01

The influence of vane sweep in rotor-stator interaction noise is investigated. In an analytical approach, the interaction of a convected gust representing the rotor viscous wake, with a cascade of cascade of finite span swept airfoils, representing the stator, is analyzed. The analysis is based on the solution of the exact linearized equations of motion. High frequency convected gusts for which noise generation is concentrated near the leading edge of airfoils is considered. In a preliminary study, the problem of an isolated finite span swept airfoil interacting with a convected gust is analyzed. Results indicate that sweep can substantially reduce the farfield noise levels for a single airfoil. Using the single airfoil model, an approximate solution to the problem of noise radiation from a cascade of finite span swept airfoils interacting with a convected gust is derived. A parametric study of noise generated by gust cascade interaction is carried out to assess the effectiveness of vane sweep in reducing rotor-stator interaction noise. The results show that sweep is beneficial in reducing noise levels. Rotor wake twist or circumferential lean substantially influences the effectiveness of vane sweep. The orientation of vane sweep must be chosen to enhance the natural phase lag caused by wake lean, in which case rather small sweep angles substantially reduce the noise levels.

Influence of vane sweep on rotor-stator interaction noise

NASA Astrophysics Data System (ADS)

Envia, Edmane; Kerschen, Edward J.

1990-12-01

The influence of vane sweep in rotor-stator interaction noise is investigated. In an analytical approach, the interaction of a convected gust representing the rotor viscous wake, with a cascade of cascade of finite span swept airfoils, representing the stator, is analyzed. The analysis is based on the solution of the exact linearized equations of motion. High frequency convected gusts for which noise generation is concentrated near the leading edge of airfoils is considered. In a preliminary study, the problem of an isolated finite span swept airfoil interacting with a convected gust is analyzed. Results indicate that sweep can substantially reduce the farfield noise levels for a single airfoil. Using the single airfoil model, an approximate solution to the problem of noise radiation from a cascade of finite span swept airfoils interacting with a convected gust is derived. A parametric study of noise generated by gust cascade interaction is carried out to assess the effectiveness of vane sweep in reducing rotor-stator interaction noise. The results show that sweep is beneficial in reducing noise levels. Rotor wake twist or circumferential lean substantially influences the effectiveness of vane sweep. The orientation of vane sweep must be chosen to enhance the natural phase lag caused by wake lean, in which case rather small sweep angles substantially reduce the noise levels.

Wind Gust Measurement Techniques-From Traditional Anemometry to New Possibilities.

PubMed

Suomi, Irene; Vihma, Timo

2018-04-23

Information on wind gusts is needed for assessment of wind-induced damage and risks to safety. The measurement of wind gust speed requires a high temporal resolution of the anemometer system, because the gust is defined as a short-duration (seconds) maximum of the fluctuating wind speed. Until the digitalization of wind measurements in the 1990s, the wind gust measurements suffered from limited recording and data processing resources. Therefore, the majority of continuous wind gust records date back at most only by 30 years. Although the response characteristics of anemometer systems are good enough today, the traditional measurement techniques at weather stations based on cup and sonic anemometers are limited to heights and regions where the supporting structures can reach. Therefore, existing measurements are mainly concentrated over densely-populated land areas, whereas from remote locations, such as the marine Arctic, wind gust information is available only from sparse coastal locations. Recent developments of wind gust measurement techniques based on turbulence measurements from research aircraft and from Doppler lidar can potentially provide new information from heights and locations unreachable by traditional measurement techniques. Moreover, fast-developing measurement methods based on Unmanned Aircraft Systems (UASs) may add to better coverage of wind gust measurements in the future. In this paper, we provide an overview of the history and the current status of anemometry from the perspective of wind gusts. Furthermore, a discussion on the potential future directions of wind gust measurement techniques is provided.

Wind Gust Measurement Techniques—From Traditional Anemometry to New Possibilities

PubMed Central

2018-01-01

Information on wind gusts is needed for assessment of wind-induced damage and risks to safety. The measurement of wind gust speed requires a high temporal resolution of the anemometer system, because the gust is defined as a short-duration (seconds) maximum of the fluctuating wind speed. Until the digitalization of wind measurements in the 1990s, the wind gust measurements suffered from limited recording and data processing resources. Therefore, the majority of continuous wind gust records date back at most only by 30 years. Although the response characteristics of anemometer systems are good enough today, the traditional measurement techniques at weather stations based on cup and sonic anemometers are limited to heights and regions where the supporting structures can reach. Therefore, existing measurements are mainly concentrated over densely-populated land areas, whereas from remote locations, such as the marine Arctic, wind gust information is available only from sparse coastal locations. Recent developments of wind gust measurement techniques based on turbulence measurements from research aircraft and from Doppler lidar can potentially provide new information from heights and locations unreachable by traditional measurement techniques. Moreover, fast-developing measurement methods based on Unmanned Aircraft Systems (UASs) may add to better coverage of wind gust measurements in the future. In this paper, we provide an overview of the history and the current status of anemometry from the perspective of wind gusts. Furthermore, a discussion on the potential future directions of wind gust measurement techniques is provided. PMID:29690647

Kinematic strategies for mitigating gust perturbations in insects.

PubMed

Vance, J T; Faruque, I; Humbert, J S

2013-03-01

Insects are attractive models for the development of micro-aerial vehicles (MAVs) due to their relatively simple sensing, actuation and control architectures as compared to vertebrates, and because of their robust flight ability in dynamic and heterogeneous environments, characterized by turbulence and gusts of wind. How do insects respond to gust perturbations? We investigated this question by perturbing freely-flying honey bees and stalk-eye flies with low-pressure bursts of compressed air to simulate a wind gust. Body and wing kinematics were analyzed from flight sequences, recorded using three high-speed digital video cameras. Bees quickly responded to body rotations caused by gusts through bilateral asymmetry in stroke amplitude, whereas stalk-eye flies used a combination of asymmetric stroke amplitude and wing rotation angle. Both insects coordinated asymmetric and symmetric kinematics in response to gusts, which provides model strategies for simple yet robust flight characteristics for MAVs.

The development of a closed-loop flight controller with panel method integration for gust alleviation using biomimetic feathers on aircraft wings

NASA Astrophysics Data System (ADS)

Blower, Christopher J.; Lee, Woody; Wickenheiser, Adam M.

2012-04-01

This paper presents the development of a biomimetic closed-loop flight controller that integrates gust alleviation and flight control into a single distributed system. Modern flight controllers predominantly rely on and respond to perturbations in the global states, resulting in rotation or displacement of the entire aircraft prior to the response. This bio-inspired gust alleviation system (GAS) employs active deflection of electromechanical feathers that react to changes in the airflow, i.e. the local states. The GAS design is a skeletal wing structure with a network of featherlike panels installed on the wing's surfaces, creating the airfoil profile and replacing the trailing-edge flaps. In this study, a dynamic model of the GAS-integrated wing is simulated to compute gust-induced disturbances. The system implements continuous adjustment to flap orientation to perform corrective responses to inbound gusts. MATLAB simulations, using a closed-loop LQR integrated with a 2D adaptive panel method, allow analysis of the morphing structure's aerodynamic data. Non-linear and linear dynamic models of the GAS are compared to a traditional single control surface baseline wing. The feedback loops synthesized rely on inertial changes in the global states; however, variations in number and location of feather actuation are compared. The bio-inspired system's distributed control effort allows the flight controller to interchange between the single and dual trailing edge flap profiles, thereby offering an improved efficiency to gust response in comparison to the traditional wing configuration. The introduction of aero-braking during continuous gusting flows offers a 25% reduction in x-velocity deviation; other flight parameters can be reduced in magnitude and deviation through control weighting optimization. Consequently, the GAS demonstrates enhancements to maneuverability and stability in turbulent intensive environments.

A reevaluaion of data on atmospheric turbulence and airplane gust loads for application in spectral calculations

NASA Technical Reports Server (NTRS)

Press, Harry; Meadows, May T; Hadlock, Ivan

1956-01-01

The available information on the spectrum of atmospheric turbulence is first briefly reviewed. On the basis of these results, methods are developed for the conversion of available gust statistics normally given in terms of counts of gusts or acceleration peaks into a form appropriate for use in spectral calculations. The fundamental quantity for this purpose appears to be the probability distribution of the root-mean-square gust velocity. Estimates of this distribution are derived from data for a number of load histories of transport operations; also, estimates of the variation of this distribution with altitude and weather condition are derived from available data and the method of applying these results to the calculation of airplane gust-response histories in operations is also outlined. (author)

Aerodynamic coefficients in generalized unsteady thin airfoil theory

NASA Technical Reports Server (NTRS)

Williams, M. H.

1980-01-01

Two cases are considered: (1) rigid body motion of an airfoil-flap combination consisting of vertical translation of given amplitude, rotation of given amplitude about a specified axis, and rotation of given amplitude of the control surface alone about its hinge; the upwash for this problem is defined mathematically; and (2) sinusoidal gust of given amplitude and wave number, for which the upwash is defined mathematically. Simple universal formulas are presented for the most important aerodynamic coefficients in unsteady thin airfoil theory. The lift and moment induced by a generalized gust are evaluated explicitly in terms of the gust wavelength. Similarly, in the control surface problem, the lift, moment, and hinge moments are given as explicit algebraic functions of hinge location. These results can be used together with any of the standard numerical inversion routines for the elementary loads (pitch and heave).

The Impact of Natural Hazards such as Turbulent Wind Gusts on the Wind Energy Conversion Process

NASA Astrophysics Data System (ADS)

Wächter, M.; Hölling, M.; Milan, P.; Morales, A.; Peinke, J.

2012-12-01

Wind turbines operate in the atmospheric boundary layer, where they are exposed to wind gusts and other types of natural hazards. As the response time of wind turbines is typically in the range of seconds, they are affected by the small scale intermittent properties of the turbulent wind. We show evidence that basic features which are known for small-scale homogeneous isotropic turbulence, and in particular the well-known intermittency problem, have an important impact on the wind energy conversion process. Intermittent statistics include high probabilities of extreme events which can be related to wind gusts and other types of natural hazards. As a summarizing result we find that atmospheric turbulence imposes its intermittent features on the complete wind energy conversion process. Intermittent turbulence features are not only present in atmospheric wind, but are also dominant in the loads on the turbine, i.e. rotor torque and thrust, and in the electrical power output signal. We conclude that profound knowledge of turbulent statistics and the application of suitable numerical as well as experimental methods are necessary to grasp these unique features and quantify their effects on all stages of wind energy conversion.

A complete second-order theory for the unsteady flow about an airfoil due to a periodic gust

NASA Technical Reports Server (NTRS)

Goldstein, M. E.; Atassi, H.

1976-01-01

A uniformly valid second-order theory is developed for calculating the unsteady incompressible flow that occurs when an airfoil is subjected to a convected sinusoidal gust. Explicit formulas for the airfoil response functions (i.e., fluctuating lift) are given. The theory accounts for the effect of the distortion of the gust by the steady-state potential flow around the airfoil, and this effect is found to have an important influence on the response functions. A number of results relevant to the general theory of the scattering of vorticity waves by solid objects are also presented.

Dynamic Response of Finite Length Maglev Vehicles Subjected to Crosswind Gusts

DOT National Transportation Integrated Search

1980-03-01

This report presents a two-degree-of-freedom model for magnetically levitated finite-length vehicles incorporating sway and yaw dynamics. Aerodynamic lateral forces and yawing moments on the vehicle resulting from constant speed wind gusts were compu...

Survey on effect of surface winds on aircraft design and operation and recommendations for needed wind research

NASA Technical Reports Server (NTRS)

Houbolt, J. C.

1973-01-01

A survey of the effect of environmental surface winds and gusts on aircraft design and operation is presented. A listing of the very large number of problems that are encountered is given. Attention is called to the many studies that have been made on surface winds and gusts, but development in the engineering application of these results to aeronautical problems is pointed out to be still in the embryonic stage. Control of the aircraft is of paramount concern. Mathematical models and their application in simulation studies of airplane operation and control are discussed, and an attempt is made to identify their main gaps or deficiencies. Key reference material is cited. The need for better exchange between the meteorologist and the aeronautical engineer is discussed. Suggestions for improvements in the wind and gust models are made.

Lift developed on unrestrained rectangular wings entering gusts at subsonic and supersonic speeds

NASA Technical Reports Server (NTRS)

Lomax, Harvard

1954-01-01

The object of this report is to provide an estimate, based on theoretical calculations, of the forces induced on a wing that is flying at a constant forward speed and suddenly enters a vertical gust. The calculations illustrate the effects of Mach number (from 0 to 2) and aspect ratio (2 to infinity), and solutions are given by means of which the response to gusts having arbitrary distributions of velocity can be calculated. The effects of pitching and wing bending are neglected and only wings of rectangular plan form are considered. Specific results are presented for sharp-edged and triangular gusts and various wing-air density ratios.

Gust Alleviation Using Direct Gust Measurement

NASA Technical Reports Server (NTRS)

Hoppe, Sven Marco

2000-01-01

The increasing competition in the market of civil aircraft leads to operating efficiency and passenger comfort being very important sales arguments. Continuous developments in jet propulsion technology helped to reduce energy consumption, as well as noise and vibrations due to the engines. The main problem with respect to ride comfort is, however, the transmittance of accelerations and jerkiness imposed by atmospheric turbulence from the wings to the fuselage. This 'gust' is also a design constraint: Light airplane structures help to save, energy, but are more critical to resist the loads imposed by turbulence. For both reasons, efficient gust alleviation is necessary to improve the performance of modern aircraft. Gust can be seen as a change in the angle of attack or as an additional varying vertical component of the headwind. The effect of gust can be very strong, since the same aerodynamic forces that keep the airplane flying are involved. Event though the frequency range of those changes is quite low, it is impossible for the pilot to alleviate gust manually. Besides, most of the time during the flight, the, autopilot maintains course and the attitude of flight. Certainly, most autopilots should be capable of damping the roughest parts of turbulence, but they are unable to provide satisfactory results in that field. A promising extension should be the application of subsidiary, control, where the inner (faster) control loop alleviates turbulence and the outer (slower) loop controls the attitude of flight. Besides the mentioned ride comfort, another reason for gust alleviation with respect to the fuselage is the sensibility of electrical devices to vibration and high values of acceleration. Many modern airplane designs--especially inherently instable military aircraft--are highly dependent on avionics. The lifetime and the reliability of these systems is thus essential.

Uncertainty Due to Unsteady Fluid/Structure Interaction for the Ares I Vehicle Traversing the Transonic Regime

NASA Technical Reports Server (NTRS)

Bartels, Robert E.

2012-01-01

Rapid reduced-order numerical models are being investigated as candidates to simulate the dynamics of a flexible launch vehicle during atmospheric ascent. There has also been the extension of these new approaches to include gust response. These methods are used to perform aeroelastic and gust response analyses at isolated Mach numbers. Such models require a method to time march through a succession of ascent Mach numbers. An approach is presented for interpolating reduced-order models of the unsteady aerodynamics at successive Mach numbers. The transonic Mach number range is considered here since launch vehicles can suffer the highest dynamic loads through this range. Realistic simulations of the flexible vehicle behavior as it traverses this Mach number range are presented. The response of the vehicle due to gusts is computed. Uncertainties in root mean square and maximum bending moment and crew module accelerations are presented due to assumed probability distributions in design parameters, ascent flight conditions, gusts. The primary focus is on the uncertainty introduced by modeling fidelity. It is found that an unsteady reduced order model produces larger excursions in the root mean square loading and accelerations than does a quasi-steady reduced order model.

Aerodynamic response of an airfoil with thickness to a longitudinal and transverse periodic gust

NASA Technical Reports Server (NTRS)

Hamad, G.; Atassi, H.

1980-01-01

The unsteady lift of an airfoil with thickness subject to a two-dimensional periodic gust is analyzed using the recent theory of Goldstein and Atassi. It is found that to properly account for the coupling between the steady potential flow and the unsteady vortical flow, one has to consider the contribution of order alpha-squared (when alpha is steady state disturbance) to the potential flowfield. A closed form analytical formula is then derived for the lift function. The results show strong dependence on the wave members of the gust.

The acoustic response of a propeller subjected to gusts incident from various inflow angles

NASA Technical Reports Server (NTRS)

Jonkouski, G. C.; Horne, W. C.; Soderman, P. T.

1983-01-01

The acoustic effect of perturbing the inflow field of a propeller was studied. The perturbation was caused by a jet of air blowing into the propeller disc from various angles, creating spanwise and chordwise flow disturbances along the blades. The effects of the gust angle, speed and turbulence, and propeller rpm and thrust are shown with narrowband spectra and directivity plots of the acoustic field. A prediction method for the peaks of the harmonics of the blade passing frequency for various gust and propeller conditions is presented.

The development of an autonomous gust insensitive unmanned aerial vehicle

NASA Astrophysics Data System (ADS)

Pisano, William James

The study of a small Unmanned Aerial Vehicle (UAV) that is designed towards eventual operation in harsh storm-like conditions is presented. Investigation of the aircraft equations of motion shows that the selection of certain aerodynamic derivatives has a significant effect on the gust response of a small unmanned aircraft. Analytical comparison of this newly formulated Autonomous Gust Insensitive Aircraft (AGIA) to a conventionally designed aircraft shows a significant reduction in undesirable roll motion caused by gusts. A simulation is presented showing that the AGIA is capable of operating in more extreme environments than a conventional aircraft, and puts less strain on the control system components in both extreme and calm environments. The role that aircraft size plays in gust response is also studied. Pilot instinct dictates that smaller aircraft are more difficult to fly in windy environments than larger ones. This phenomenon is investigated using an analytic approach, providing insight into why smaller aircraft are indeed more difficult to fly in more challenging environments. As an aircraft gets smaller, its natural aerodynamic modes and response get faster. In an ideal system, this does not limit small aircraft to poor performance (in fact it will be shown that idealized small aircraft theoretically perform better than their larger counterparts). A more realistic system is presented that includes not only aerodynamics, but also realistic sensor and actuator dynamics. It is shown that these additional dynamics become a limiting factor in control system performance, and thus limit the closed-loop flight performance of small aircraft in turbulent environments. It is shown that the AGIA design approach plays a more significant role the as an aircraft gets smaller. To provide experimental validation of the gust insensitive theory presented herein, a representative small conventional aircraft was built alongside a similar aircraft that incorporated the AGIA design characteristics. These two aircraft were flown simultaneously and autonomously using the autopilot developed by the Author. Data from this experiment strongly supports the hypothesis that the AGIA is less sensitive to gusts than its conventional counterpart, and that flight of the AGIA puts less strain on the control system components in flight.

Response of a tethered aerostat to simulated turbulence

NASA Astrophysics Data System (ADS)

Stanney, Keith A.; Rahn, Christopher D.

2006-09-01

Aerostats are lighter-than-air vehicles tethered to the ground by a cable and used for broadcasting, communications, surveillance, and drug interdiction. The dynamic response of tethered aerostats subject to extreme atmospheric turbulence often dictates survivability. This paper develops a theoretical model that predicts the planar response of a tethered aerostat subject to atmospheric turbulence and simulates the response to 1000 simulated hurricane scale turbulent time histories. The aerostat dynamic model assumes the aerostat hull to be a rigid body with non-linear fluid loading, instantaneous weathervaning for planar response, and a continuous tether. Galerkin's method discretizes the coupled aerostat and tether partial differential equations to produce a non-linear initial value problem that is integrated numerically given initial conditions and wind inputs. The proper orthogonal decomposition theorem generates, based on Hurricane Georges wind data, turbulent time histories that possess the sequential behavior of actual turbulence, are spectrally accurate, and have non-Gaussian density functions. The generated turbulent time histories are simulated to predict the aerostat response to severe turbulence. The resulting probability distributions for the aerostat position, pitch angle, and confluence point tension predict the aerostat behavior in high gust environments. The dynamic results can be up to twice as large as a static analysis indicating the importance of dynamics in aerostat modeling. The results uncover a worst case wind input consisting of a two-pulse vertical gust.

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2011 CFR

2011-01-01

... establishing the dynamic response of the airplane to vertical and lateral continuous turbulence unless a more... determined by dynamic analysis. The power spectral density of the atmospheric turbulence must be as given by... obtained by multiplying the Ā values determined by the dynamic analysis by the following values of the gust...

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2010 CFR

2010-01-01

... establishing the dynamic response of the airplane to vertical and lateral continuous turbulence unless a more... determined by dynamic analysis. The power spectral density of the atmospheric turbulence must be as given by... obtained by multiplying the Ā values determined by the dynamic analysis by the following values of the gust...

Unsteady aerodynamic characterization of a military aircraft in vertical gusts

NASA Technical Reports Server (NTRS)

Lebozec, A.; Cocquerez, J. L.

1985-01-01

The effects of 2.5-m/sec vertical gusts on the flight characteristics of a 1:8.6 scale model of a Mirage 2000 aircraft in free flight at 35 m/sec over a distance of 30 m are investigated. The wind-tunnel setup and instrumentation are described; the impulse-response and local-coefficient-identification analysis methods applied are discussed in detail; and the modification and calibration of the gust-detection probes are reviewed. The results are presented in graphs, and good general agreement is obtained between model calculations using the two analysis methods and the experimental measurements.

A study of the application of power-spectral methods of generalized harmonic analysis to gust loads on airplanes

NASA Technical Reports Server (NTRS)

Press, Harry; Mazelsky, Bernard

1954-01-01

The applicability of some results from the theory of generalized harmonic analysis (or power-spectral analysis) to the analysis of gust loads on airplanes in continuous rough air is examined. The general relations for linear systems between power spectrums of a random input disturbance and an output response are used to relate the spectrum of airplane load in rough air to the spectrum of atmospheric gust velocity. The power spectrum of loads is shown to provide a measure of the load intensity in terms of the standard deviation (root mean square) of the load distribution for an airplane in flight through continuous rough air. For the case of a load output having a normal distribution, which appears from experimental evidence to apply to homogeneous rough air, the standard deviation is shown to describe the probability distribution of loads or the proportion of total time that the load has given values. Thus, for airplane in flight through homogeneous rough air, the probability distribution of loads may be determined from a power-spectral analysis. In order to illustrate the application of power-spectral analysis to gust-load analysis and to obtain an insight into the relations between loads and airplane gust-response characteristics, two selected series of calculations are presented. The results indicate that both methods of analysis yield results that are consistent to a first approximation.

Wind tunnel test of a variable-diameter tiltrotor (VDTR) model

NASA Technical Reports Server (NTRS)

Matuska, David; Dale, Allen; Lorber, Peter

1994-01-01

This report documents the results from a wind tunnel test of a 1/6th scale Variable Diameter Tiltrotor (VDTR). This test was a joint effort of NASA Ames and Sikorsky Aircraft. The objective was to evaluate the aeroelastic and performance characteristics of the VDTR in conversion, hover, and cruise. The rotor diameter and nacelle angle of the model were remotely changed to represent tiltrotor operating conditions. Data is presented showing the propulsive force required in conversion, blade loads, angle of attack stability and simulated gust response, and hover and cruise performance. This test represents the first wind tunnel test of a variable diameter rotor applied to a tiltrotor concept. The results confirm some of the potential advantages of the VDTR and establish the variable diameter rotor a viable candidate for an advanced tiltrotor. This wind tunnel test successfully demonstrated the feasibility of the Variable Diameter rotor for tilt rotor aircraft. A wide range of test points were taken in hover, conversion, and cruise modes. The concept was shown to have a number of advantages over conventional tiltrotors such as reduced hover downwash with lower disk loading and significantly reduced longitudinal gust response in cruise. In the conversion regime, a high propulsive force was demonstrated for sustained flight with acceptable blade loads. The VDTR demonstrated excellent gust response capabilities. The horizontal gust response correlated well with predictions revealing only half the response to turbulence of the conventional civil tiltrotor.

Subsynoptic-scale features associated with extreme surface gusts in UK extratropical cyclone events

NASA Astrophysics Data System (ADS)

Earl, N.; Dorling, S.; Starks, M.; Finch, R.

2017-04-01

Numerous studies have addressed the mesoscale features within extratropical cyclones (ETCs) that are responsible for the most destructive winds, though few have utilized surface observation data, and most are based on case studies. By using a 39-station UK surface observation network, coupled with in-depth analysis of the causes of extreme gusts during the period 2008-2014, we show that larger-scale features (warm and cold conveyer belts) are most commonly associated with the top 1% of UK gusts but smaller-scale features generate the most extreme winds. The cold conveyor belt is far more destructive when joining the momentum of the ETC, rather than earlier in its trajectory, ahead of the approaching warm front. Sting jets and convective lines account for two thirds of severe surface gusts in the UK.

Finite Element Aircraft Simulation of Turbulence

NASA Technical Reports Server (NTRS)

McFarland, R. E.

1997-01-01

A turbulence model has been developed for realtime aircraft simulation that accommodates stochastic turbulence and distributed discrete gusts as a function of the terrain. This model is applicable to conventional aircraft, V/STOL aircraft, and disc rotor model helicopter simulations. Vehicle angular activity in response to turbulence is computed from geometrical and temporal relationships rather than by using the conventional continuum approximations that assume uniform gust immersion and low frequency responses. By using techniques similar to those recently developed for blade-element rotor models, the angular-rate filters of conventional turbulence models are not required. The model produces rotational rates as well as air mass translational velocities in response to both stochastic and deterministic disturbances, where the discrete gusts and turbulence magnitudes may be correlated with significant terrain features or ship models. Assuming isotropy, a two-dimensional vertical turbulence field is created. A novel Gaussian interpolation technique is used to distribute vertical turbulence on the wing span or lateral rotor disc, and this distribution is used to compute roll responses. Air mass velocities are applied at significant centers of pressure in the computation of the aircraft's pitch and roll responses.

Assessing the Transient Gust Response of a Representative Ship Airwake using Proper Orthogonal Decomposition

DTIC Science & Technology

Velocimetry system was then used to acquire flow field data across a series of three horizontal planes spanning from 0.25 to 1.5 times the ship hangar height...included six separate data points at gust-frequency referenced Strouhal numbers ranging from 0.430 to1.474. A 725-Hertz time -resolved Particle Image

Forced response analysis of an aerodynamically detuned supersonic turbomachine rotor

NASA Technical Reports Server (NTRS)

Hoyniak, D.; Fleeter, S.

1985-01-01

High performance aircraft-engine fan and compressor blades are vulnerable to aerodynamically forced vibrations generated by inlet flow distortions due to wakes from upstream blade and vane rows, atmospheric gusts, and maldistributions in inlet ducts. In this report, an analysis is developed to predict the flow-induced forced response of an aerodynamically detuned rotor operating in a supersonic flow with a subsonic axial component. The aerodynamic detuning is achieved by alternating the circumferential spacing of adjacent rotor blades. The total unsteady aerodynamic loading acting on the blading, as a result of the convection of the transverse gust past the airfoil cascade and the resulting motion of the cascade, is developed in terms of influence coefficients. This analysis is used to investigate the effect of aerodynamic detuning on the forced response of a 12-blade rotor, with Verdon's Cascade B flow geometry as a uniformly spaced baseline configuration. The results of this study indicate that, for forward traveling wave gust excitations, aerodynamic detuning is very beneficial, resulting in significantly decreased maximum-amplitude blade responses for many interblade phase angles.

Simulation study of gust alleviation in a tilt rotor aircraft, volume 1

NASA Technical Reports Server (NTRS)

Amos, A. K.; Alexander, H. R.

1977-01-01

The response to vertical turbulence in cruise of the HTR XV-15 design is studied using simulation techniques. This design is a modified version of the XV-15 with a hingeless fiberglass soft-in-plane rotor system. The parameters of a gust alleviation system are determined and the performance of the system is evaluated over a range of cruise velocities and altitudes.

Vector wind profile gust model

NASA Technical Reports Server (NTRS)

Adelfang, S. I.

1981-01-01

To enable development of a vector wind gust model suitable for orbital flight test operations and trade studies, hypotheses concerning the distributions of gust component variables were verified. Methods for verification of hypotheses that observed gust variables, including gust component magnitude, gust length, u range, and L range, are gamma distributed and presented. Observed gust modulus has been drawn from a bivariate gamma distribution that can be approximated with a Weibull distribution. Zonal and meridional gust components are bivariate gamma distributed. An analytical method for testing for bivariate gamma distributed variables is presented. Two distributions for gust modulus are described and the results of extensive hypothesis testing of one of the distributions are presented. The validity of the gamma distribution for representation of gust component variables is established.

Vector wind profile gust model

NASA Technical Reports Server (NTRS)

Adelfang, S. I.

1979-01-01

Work towards establishing a vector wind profile gust model for the Space Transportation System flight operations and trade studies is reported. To date, all the statistical and computational techniques required were established and partially implemented. An analysis of wind profile gust at Cape Kennedy within the theoretical framework is presented. The variability of theoretical and observed gust magnitude with filter type, altitude, and season is described. Various examples are presented which illustrate agreement between theoretical and observed gust percentiles. The preliminary analysis of the gust data indicates a strong variability with altitude, season, and wavelength regime. An extension of the analyses to include conditional distributions of gust magnitude given gust length, distributions of gust modulus, and phase differences between gust components has begun.

Multi-disciplinary optimization of aeroservoelastic systems

NASA Technical Reports Server (NTRS)

Karpel, Mardechay

1992-01-01

The purpose of the research project was to continue the development of new methods for efficient aeroservoelastic analysis and optimization. The main targets were as follows: to complete the development of analytical tools for the investigation of flutter with large stiffness changes; to continue the work on efficient continuous gust response and sensitivity derivatives; and to advance the techniques of calculating dynamic loads with control and unsteady aerodynamic effects. An efficient and highly accurate mathematical model for time-domain analysis of flutter during which large structural changes occur was developed in cooperation with Carol D. Wieseman of NASA LaRC. The model was based on the second-year work 'Modal Coordinates for Aeroelastic Analysis with Large Local Structural Variations'. The work on continuous gust response was completed. An abstract of the paper 'Continuous Gust Response and Sensitivity Derivatives Using State-Space Models' was submitted for presentation in the 33rd Israel Annual Conference on Aviation and Astronautics, Feb. 1993. The abstract is given in Appendix A. The work extends the optimization model to deal with continuous gust objectives in a way that facilitates their inclusion in the efficient multi-disciplinary optimization scheme. Currently under development is a work designed to extend the analysis and optimization capabilities to loads and stress considerations. The work is on aircraft dynamic loads in response to impulsive and non-impulsive excitation. The work extends the formulations of the mode-displacement and summation-of-forces methods to include modes with significant local distortions, and load modes. An abstract of the paper,'Structural Dynamic Loads in Response to Impulsive Excitation' is given in appendix B. Another work performed this year under the Grant was 'Size-Reduction Techniques for the Determination of Efficient Aeroservoelastic Models' given in Appendix C.

User's Manual for Computer Program ROTOR. [to calculate tilt-rotor aircraft dynamic characteristics

NASA Technical Reports Server (NTRS)

Yasue, M.

1974-01-01

A detailed description of a computer program to calculate tilt-rotor aircraft dynamic characteristics is presented. This program consists of two parts: (1) the natural frequencies and corresponding mode shapes of the rotor blade and wing are developed from structural data (mass distribution and stiffness distribution); and (2) the frequency response (to gust and blade pitch control inputs) and eigenvalues of the tilt-rotor dynamic system, based on the natural frequencies and mode shapes, are derived. Sample problems are included to assist the user.

Gust alleviation for a STOL transport by using elevator, spoilers, and flaps

NASA Technical Reports Server (NTRS)

Lallman, F. J.

1974-01-01

Control laws were developed to investigate methods of alleviating the response of a STOL transport to gusty air. The transport considered in the study had triple-slotted, externally blown jet flaps and a large T-tail. The control devices used were the elevator, spoilers, and flaps. A hybrid computing system was used to simulate linearized longitudinal dynamics of the aircraft and to implement a conjugate gradient optimal search algorithm. The aircraft was simulated in the low-speed approach condition only. Feedback control matrices were found which minimized the average of a quadratic functional involving passenger compartment accelerations, pitch angle and rate, flight path angle and speed variations. The optimization was performed for artificially designed gust inputs in the form of predetermined rectangular waveforms. Results were obtained for elevator, spoilers, and flaps acting singly and in combination. Additional results were obtained for unit sinusoidal gust inputs by using the gain matrices computed for the artificial test gusts. Various sensor configurations were also investigated.

Overview and first results of the Wind and Storms Experiment (WASTEX): a field campaign to observe the formation of gusts using a Doppler lidar

NASA Astrophysics Data System (ADS)

Pantillon, Florian; Wieser, Andreas; Adler, Bianca; Corsmeier, Ulrich; Knippertz, Peter

2018-05-01

Wind gusts are responsible for most damages in winter storms over central Europe, but capturing their small scale and short duration is a challenge for both models and observations. This motivated the Wind and Storms Experiment (WASTEX) dedicated to investigate the formation of gusts during the passage of extratropical cyclones. The field campaign took place during the winter 2016-2017 on a former waste deposit located close to Karlsruhe in the Upper Rhine Valley in southwest Germany. Twelve extratropical cyclones were sampled during WASTEX with a Doppler lidar system performing vertical scans in the mean wind direction and complemented with a Doppler C-band radar and a 200 m instrumented tower. First results are provided here for the three most intense storms and include a potential sting jet, a unique direct observation of a convective gust and coherent boundary-layer structures of strong winds.

Three-dimensional dynamics of scientific balloon systems in response to sudden gust loadings. [including a computer program user manual

NASA Technical Reports Server (NTRS)

Dorsey, D. R., Jr.

1975-01-01

A mathematical model was developed of the three-dimensional dynamics of a high-altitude scientific research balloon system perturbed from its equilibrium configuration by an arbitrary gust loading. The platform is modelled as a system of four coupled pendula, and the equations of motion were developed in the Lagrangian formalism assuming a small-angle approximation. Three-dimensional pendulation, torsion, and precessional motion due to Coriolis forces are considered. Aerodynamic and viscous damping effects on the pendulatory and torsional motions are included. A general model of the gust field incident upon the balloon system was developed. The digital computer simulation program is described, and a guide to its use is given.

Comparisons of several aerodynamic methods for application to dynamic loads analyses

NASA Technical Reports Server (NTRS)

Kroll, R. I.; Miller, R. D.

1976-01-01

The results of a study are presented in which the applicability at subsonic speeds of several aerodynamic methods for predicting dynamic gust loads on aircraft, including active control systems, was examined and compared. These aerodynamic methods varied from steady state to an advanced unsteady aerodynamic formulation. Brief descriptions of the structural and aerodynamic representations and of the motion and load equations are presented. Comparisons of numerical results achieved using the various aerodynamic methods are shown in detail. From these results, aerodynamic representations for dynamic gust analyses are identified. It was concluded that several aerodynamic methods are satisfactory for dynamic gust analyses of configurations having either controls fixed or active control systems that primarily affect the low frequency rigid body aircraft response.

Strain actuated aeroelastic control

NASA Technical Reports Server (NTRS)

Lazarus, Kenneth B.

1992-01-01

Viewgraphs on strain actuated aeroelastic control are presented. Topics covered include: structural and aerodynamic modeling; control law design methodology; system block diagram; adaptive wing test article; bench-top experiments; bench-top disturbance rejection: open and closed loop response; bench-top disturbance rejection: state cost versus control cost; wind tunnel experiments; wind tunnel gust alleviation: open and closed loop response at 60 mph; wind tunnel gust alleviation: state cost versus control cost at 60 mph; wind tunnel command following: open and closed loop error at 60 mph; wind tunnel flutter suppression: open loop flutter speed; and wind tunnel flutter suppression: closed loop state cost curves.

Passive control of aerodynamically forced vibrations of supersonic turbomachine rotors by splitter blades

NASA Technical Reports Server (NTRS)

Fleeter, S.; Topp, D. A.; Hoyniak, D.

1986-01-01

An aeroelastic model is developed to examine the use of splitter blades as a passive detuning mechanism for flow induced forced response of unstalled supersonic turbomachine rotors. The splitters introduce aerodynamic and structural detuning to the rotor design. The relationship between aerodynamic and structural detuning and the location and chord lengths of splitters is analyzed. The model is applied to the flow induced response of four 12-blade rotors with Verdon's (1973) Cascade B flow geometry. The data reveal that for gusts characterized by forward and backward traveling waves the splitters generally decrease the maximum amplitudes of response; however, for some gust load interblade phase angles, such as -180 deg and 120 deg the splitters did not reduce the amplitudes of response.

Compressible flows with periodic vortical disturbances around lifting airfoils. Ph.D. Thesis - Notre Dame Univ.

NASA Technical Reports Server (NTRS)

Scott, James R.

1991-01-01

A numerical method is developed for solving periodic, three-dimensional, vortical flows around lifting airfoils in subsonic flow. The first-order method that is presented fully accounts for the distortion effects of the nonuniform mean flow on the convected upstream vortical disturbances. The unsteady velocity is split into a vortical component which is a known function of the upstream flow conditions and the Lagrangian coordinates of the mean flow, and an irrotational field whose potential satisfies a nonconstant-coefficient, inhomogeneous, convective wave equation. Using an elliptic coordinate transformation, the unsteady boundary value problem is solved in the frequency domain on grids which are determined as a function of the Mach number and reduced frequency. The numerical scheme is validated through extensive comparisons with known solutions to unsteady vortical flow problems. In general, it is seen that the agreement between the numerical and analytical results is very good for reduced frequencies ranging from 0 to 4, and for Mach numbers ranging from .1 to .8. Numerical results are also presented for a wide variety of flow configurations for the purpose of determining the effects of airfoil thickness, angle of attack, camber, and Mach number on the unsteady lift and moment of airfoils subjected to periodic vortical gusts. It is seen that each of these parameters can have a significant effect on the unsteady airfoil response to the incident disturbances, and that the effect depends strongly upon the reduced frequency and the dimensionality of the gust. For a one-dimensional (transverse) or two-dimensional (transverse and longitudinal) gust, the results indicate that airfoil thickness increases the unsteady lift and moment at the low reduced frequencies but decreases it at the high reduced frequencies. The results show that an increase in airfoil Mach number leads to a significant increase in the unsteady lift and moment for the low reduced frequencies, but a significant decrease for the high reduced frequencies.

Aerodynamic loads on buses due to crosswind gusts: extended analysis

NASA Astrophysics Data System (ADS)

Drugge, Lars; Juhlin, Magnus

2010-12-01

The objective of this work is to use inverse simulations on measured vehicle data in order to estimate the aerodynamic loads on a bus when exposed to crosswind situations. Tyre forces, driver input, wind velocity and vehicle response were measured on a typical coach when subjected to natural crosswind gusts. Based on these measurements and a detailed MBS vehicle model, the aerodynamic loads were estimated through inverse simulations. In order to estimate the lift force, roll and pitch moments in addition to the lateral force and yaw moment, the simulation model was extended by also incorporating the estimation of the vertical road disturbances. The proposed method enables the estimation of aerodynamic loads due to crosswind gusts without using a full scale wind tunnel adapted for crosswind excitation.

Exploratory Studies in Generalized Predictive Control for Active Gust Load Alleviation

NASA Technical Reports Server (NTRS)

Kvaternik, Raymond G.; Eure, Kenneth W.; Juang, Jer-Nan

2006-01-01

The results of numerical simulations aimed at assessing the efficacy of Generalized Predictive Control (GPC) for active gust load alleviation using trailing- and leading-edge control surfaces are presented. The equations underlying the method are presented and discussed, including system identification, calculation of control law matrices, and calculation of commands applied to the control effectors. Both embedded and explicit feedforward paths for inclusion of disturbance effects are addressed. Results from two types of simulations are shown. The first used a 3-DOF math model of a mass-spring-dashpot system subject to user-defined external disturbances. The second used open-loop data from a wind-tunnel test in which a wing model was excited by sinusoidal vertical gusts; closed-loop behavior was simulated in post-test calculations. Results obtained from these simulations have been decidedly positive. In particular, results of closed-loop simulations for the wing model showed reductions in root moments by factors as high as 1000, depending on whether the excitation is from a constant- or variable-frequency gust and on the direction of the response.

Comparison of analytical and wind-tunnel results for flutter and gust response of a transport wing with active controls

NASA Technical Reports Server (NTRS)

Abel, I.; Perry, B., III; Newsom, J. R.

1982-01-01

Two flutter suppression control laws wre designed and tested on a low speed aeroelastic model of a DC-10 derivative wing. Both control laws demontrated increases in flutter speed in excess of 25 percent above the passive wing flutter speed. In addition, one of the control laws was effective in reducing loads due to turbulence generated in the wind tunnel. The effect of variations in gain and phase on the closed-loop performance was measured and is compared with predictions. In general, both flutter and gust response predictions agree reasonably well with experimental data.

Development of a linearized unsteady aerodynamic analysis for cascade gust response predictions

NASA Technical Reports Server (NTRS)

Verdon, Joseph M.; Hall, Kenneth C.

1990-01-01

A method for predicting the unsteady aerodynamic response of a cascade of airfoils to entropic, vortical, and acoustic gust excitations is being developed. Here, the unsteady flow is regarded as a small perturbation of a nonuniform isentropic and irrotational steady background flow. A splitting technique is used to decompose the linearized unsteady velocity into rotational and irrotational parts leading to equations for the complex amplitudes of the linearized unsteady entropy, rotational velocity, and velocity potential that are coupled only sequentially. The entropic and rotational velocity fluctuations are described by transport equations for which closed-form solutions in terms of the mean-flow drift and stream functions can be determined. The potential fluctuation is described by an inhomogeneous convected wave equation in which the source term depends on the rotational velocity field, and is determined using finite-difference procedures. The analytical and numerical techniques used to determine the linearized unsteady flow are outlined. Results are presented to indicate the status of the solution procedure and to demonstrate the impact of blade geometry and mean blade loading on the aerodynamic response of cascades to vortical gust excitations. The analysis described herein leads to very efficient predictions of cascade unsteady aerodynamic response phenomena making it useful for turbomachinery aeroelastic and aeroacoustic design applications.

A comprehensive analytical model of rotorcraft aerodynamics and dynamics. Part 3: Program manual

NASA Technical Reports Server (NTRS)

Johnson, W.

1980-01-01

The computer program for a comprehensive analytical model of rotorcraft aerodynamics and dynamics is described. This analysis is designed to calculate rotor performance, loads, and noise; the helicopter vibration and gust response; the flight dynamics and handling qualities; and the system aeroelastic stability. The analysis is a combination of structural, inertial, and aerodynamic models that is applicable to a wide range of problems and a wide class of vehicles. The analysis is intended for use in the design, testing, and evaluation of rotors and rotorcraft and to be a basis for further development of rotary wing theories.

A non-gaussian model of continuous atmospheric turbulence for use in aircraft design

NASA Technical Reports Server (NTRS)

Reeves, P. M.; Joppa, R. G.; Ganzer, V. M.

1976-01-01

A non-Gaussian model of atmospheric turbulence is presented and analyzed. The model is restricted to the regions of the atmosphere where the turbulence is steady or continuous, and the assumptions of homogeneity and stationarity are justified. Also spatial distribution of turbulence is neglected, so the model consists of three independent, stationary stochastic processes which represent the vertical, lateral, and longitudinal gust components. The non-Gaussian and Gaussian models are compared with experimental data, and it is shown that the Gaussian model underestimates the number of high velocity gusts which occur in the atmosphere, while the non-Gaussian model can be adjusted to match the observed high velocity gusts more satisfactorily. Application of the proposed model to aircraft response is investigated, with particular attention to the response power spectral density, the probability distribution, and the level crossing frequency. A numerical example is presented which illustrates the application of the non-Gaussian model to the study of an aircraft autopilot system. Listings and sample results of a number of computer programs used in working with the model are included.

Flutter suppression and gust alleviation using active controls

NASA Technical Reports Server (NTRS)

Nissim, E.

1975-01-01

Application of the aerodynamic energy approach to some problems of flutter suppression and gust alleviation were considered. A simple modification of the control-law is suggested for achieving the required pitch control in the use of a leading edge - trailing edge activated strip. The possible replacement of the leading edge - trailing edge activated strip by a trailing edge - tab strip is also considered as an alternate solution. Parameters affecting the performance of the activated leading edge - trailing edge strip were tested on the Arava STOL Transport and the Westwind Executive Jet Transport and include strip location, control-law gains and a variation in the control-law itself.

Fourth Computational Aeroacoustics (CAA) Workshop on Benchmark Problems

NASA Technical Reports Server (NTRS)

Dahl, Milo D. (Editor)

2004-01-01

This publication contains the proceedings of the Fourth Computational Aeroacoustics (CAA) Workshop on Benchmark Problems. In this workshop, as in previous workshops, the problems were devised to gauge the technological advancement of computational techniques to calculate all aspects of sound generation and propagation in air directly from the fundamental governing equations. A variety of benchmark problems have been previously solved ranging from simple geometries with idealized acoustic conditions to test the accuracy and effectiveness of computational algorithms and numerical boundary conditions; to sound radiation from a duct; to gust interaction with a cascade of airfoils; to the sound generated by a separating, turbulent viscous flow. By solving these and similar problems, workshop participants have shown the technical progress from the basic challenges to accurate CAA calculations to the solution of CAA problems of increasing complexity and difficulty. The fourth CAA workshop emphasized the application of CAA methods to the solution of realistic problems. The workshop was held at the Ohio Aerospace Institute in Cleveland, Ohio, on October 20 to 22, 2003. At that time, workshop participants presented their solutions to problems in one or more of five categories. Their solutions are presented in this proceedings along with the comparisons of their solutions to the benchmark solutions or experimental data. The five categories for the benchmark problems were as follows: Category 1:Basic Methods. The numerical computation of sound is affected by, among other issues, the choice of grid used and by the boundary conditions. Category 2:Complex Geometry. The ability to compute the sound in the presence of complex geometric surfaces is important in practical applications of CAA. Category 3:Sound Generation by Interacting With a Gust. The practical application of CAA for computing noise generated by turbomachinery involves the modeling of the noise source mechanism as a vortical gust interacting with an airfoil. Category 4:Sound Transmission and Radiation. Category 5:Sound Generation in Viscous Problems. Sound is generated under certain conditions by a viscous flow as the flow passes an object or a cavity.

Gust response of commercial jet aircraft including effects of autopilot operation

NASA Technical Reports Server (NTRS)

Goldberg, J. H.

1982-01-01

A simplified theory of aircraft vertical acceleration gust response based on a model including pitch, vertical displacement and control motions due to autopilot operation is presented. High-order autopilot transfer functions are utilized for improved accuracy in the determination of the overall response characteristics. Four representative commercial jet aircraft were studied over a wide range of operating conditions and comparisons of individual responses are given. It is shown that autopilot operation relative to the controls fixed case causes response attenuation of from 10 percent to approximately 25 percent depending on flight condition and increases in crossing number up to 30 percent, with variations between aircraft of from 5 percent to 10 percent, in general, reflecting the differences in autopilot design. A detailed computer program description and listing of the calculation procedure suitable for the general application of the theory to any airplane autopilot combination is also included.

Response of a rigid aircraft to nonstationary atmospheric turbulence.

NASA Technical Reports Server (NTRS)

Verdon, J. M.; Steiner, R.

1973-01-01

The plunging response of an aircraft to a type of nonstationary turbulent excitation is considered. The latter consists of stationary Gaussian noise modulated by a well-defined envelope function. The intent of the investigation is to model the excitation experienced by an airplane flying through turbulence of varying intensity and to examine the influence of intensity variations on exceedance frequencies of the gust velocity and the airplane's plunging velocity and acceleration. One analytical advantage of the proposed model is that the Gaussian assumption for the gust excitation is retained. The analysis described herein is developed in terms of an envelope function of arbitrary form; however, numerical calculations are limited to the case of harmonic modulation.

Generalized extreme gust wind speeds distributions

USGS Publications Warehouse

Cheng, E.; Yeung, C.

2002-01-01

Since summer 1996, the US wind engineers are using the extreme gust (or 3-s gust) as the basic wind speed to quantify the destruction of extreme winds. In order to better understand these destructive wind forces, it is important to know the appropriate representations of these extreme gust wind speeds. Therefore, the purpose of this study is to determine the most suitable extreme value distributions for the annual extreme gust wind speeds recorded in large selected areas. To achieve this objective, we are using the generalized Pareto distribution as the diagnostic tool for determining the types of extreme gust wind speed distributions. The three-parameter generalized extreme value distribution function is, thus, reduced to either Type I Gumbel, Type II Frechet or Type III reverse Weibull distribution function for the annual extreme gust wind speeds recorded at a specific site.With the considerations of the quality and homogeneity of gust wind data collected at more than 750 weather stations throughout the United States, annual extreme gust wind speeds at selected 143 stations in the contiguous United States were used in the study. ?? 2002 Elsevier Science Ltd. All rights reserved.

Wing-Fixed PIV and force measurements of a large transverse gust encounter

NASA Astrophysics Data System (ADS)

Perrotta, Gino

2015-11-01

The unsteady aerodynamics of an aspect ratio 4 flat plate wing encountering a large-amplitude transverse gust were investigated using PIV in the wing-fixed reference frame and direct unsteady force measurements. Using a new experimental facility at the University of Maryland, the wing was towed at Reynolds number 20,000 through a 7m-long tank of nominally quiescent water containing a single cross-stream planar jet with velocity equal to the wing's towed velocity - a transverse gust ratio equal to one. The planar jet was created by pumping water through 30 cylindrical nozzles arranged in a single row. PIV confirms that the individual jets converge into a single, narrow, planar gust with a streamwise velocity profile resembling a canonical cosine-squared gust. Forces and fluid velocities of this wing-gust interaction will be presented for two pre-gust conditions: attached flow on the wing and stalled flow over the wing. In both cases, the gust encounter results in a momentary spike in lift coefficient. The peak lift coefficient was measured between 3 and 6 and varies with angle of attack. At low angle of attack, the attached flow wing produces less lift before the gust and much more (non-circulatory) lift during the gust than the stalled wing. Although the flow over the wing at low angle of attack separates during the gust and reattaches afterwards, the recovery time is similar to that of the high angle case, on the order of 10 chord lengths travelled.

A Time Domain Analysis of Gust-Cascade Interaction Noise

NASA Technical Reports Server (NTRS)

Nallasamy, M.; Hixon, R.; Sawyer, S. D.; Dyson, R. W.

2003-01-01

The gust response of a 2 D cascade is studied by solving the full nonlinear Euler equations employing higher order accurate spatial differencing and time stepping techniques. The solutions exhibit the exponential decay of the two circumferential mode orders of the cutoff blade passing frequency (BPF) tone and propagation of one circumferential mode order at 2BPF, as would be expected for the flow configuration considered. Two frequency excitations indicate that the interaction between the frequencies and the self interaction contribute to the amplitude of the propagating mode.

Spirit Feels Dust Gust

NASA Technical Reports Server (NTRS)

2007-01-01

On sol 1149 (March 28, 2007) of its mission, NASA's Mars Exploration Rover Spirit caught a wind gust with its navigation camera. A series of navigation camera images were strung together to create this movie. The front of the gust is observable because it was strong enough to lift up dust. From assessing the trajectory of this gust, the atmospheric science team concludes that it is possible that it passed over the rover. There was, however, no noticeable increase in power associated with this gust. In the past, dust devils and gusts have wiped the solar panels of dust, making it easier for the solar panels to absorb sunlight.

Effect of limited amplitude and rate of flap motion on vane-controlled gust alleviation system

NASA Technical Reports Server (NTRS)

Barker, L. K.; Crawford, D. J.; Sparrow, G. W.

1972-01-01

An airplane (light transport type) is assumed to be in level flight (no pitching) through atmospheric turbulence which has a mean-square vertical gust intensity of 9.3 (m/sec)sq. The power spectral density of the vertical acceleration due to gusts is examined with and without a gust-alleviation system in operation. The gust-alleviation system consisted of wing flaps that were used in conjunction with a vane mounted ahead of the airplane to sense the vertical gust velocity. The primary purpose of this study was to examine the change in the effectiveness of the gust-alleviation system when the flap motion is limited in amplitude and rate. The alleviation system was very effective if no restrictions were placed on flap motion (rate and amplitude). Restricting the flap amplitude to 0.5 radian did not appreciably change the effectiveness. However, restricting the flap rate did reduce the gust alleviation, and restricting the flap rate to 0.25 rad/sec actually caused the alleviation system to increase the vertical acceleration above that for the no-alleviation situation. Based upon this analysis, rate limiting appears to be rather significant in gust-alleviation systems designed for passenger comfort.

14 CFR 25.341 - Gust and turbulence loads.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.341 Gust and turbulence loads. (a) Discrete Gust Design Criteria. The airplane is assumed to be subjected... accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic...

14 CFR 25.341 - Gust and turbulence loads.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.341 Gust and turbulence loads. (a) Discrete Gust Design Criteria. The airplane is assumed to be subjected... accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic...

14 CFR 25.341 - Gust and turbulence loads.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.341 Gust and turbulence loads. (a) Discrete Gust Design Criteria. The airplane is assumed to be subjected... accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic...

14 CFR 25.341 - Gust and turbulence loads.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.341 Gust and turbulence loads. (a) Discrete Gust Design Criteria. The airplane is assumed to be subjected... accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic...

How birds can negate gusts and maintain heading by crabbing into the wind passively

NASA Astrophysics Data System (ADS)

Quinn, Daniel; Kress, Daniel; Stein, Andrea; Wegrzynski, Michal; Hamzah, Latifah; Lentink, David

2017-11-01

Everyday observations show birds flying stably in strong lateral gusts in which aerial robots cannot operate reliably. However, the mechanisms that birds use to negate lateral gusts are unknown. Therefore, we studied the motions of lovebirds as they flew through strong gusts in a long mesh corridor. The corridor was painted to simulate a forest (vertical stripes), a lake (horizontal stripe), and a cave (dark with a small light at the end). Fan arrays outside the corridor imposed three wind conditions: still air, a uniform gust, and wind shear. We found that lovebirds consistently yaw their body into the wind direction, crabbing like a fixed-wing aircraft, while keeping their head oriented towards the landing perch, unlike aircraft. These results were the same for all three visual conditions, showing how lovebirds can even negate gusts in the dark with a faint point source as a target. Because the naive birds had never experienced gusts before, the gust mitigation behavior is innate. Motivated by these observations, we developed a physical model that shows how yaw corrections can be passive in flapping flight. Our model offers a foundation for understanding wind negation in birds and other flying animals and offers inspiration for aerial robots that are more robust to gusts. How birds can negate gusts and maintain heading by crabbing into the wind passively.

Recent advances in aerodynamic energy concept for flutter suppression and gust alleviation using active controls

NASA Technical Reports Server (NTRS)

Nissim, E.

1977-01-01

Control laws are derived, by using realizable transfer functions, which permit relaxation of the stability requirements of the aerodynamic energy concept. The resulting aerodynamic eigenvalues indicate that both the trailing edge and the leading edge-trailing edge control systems can be made more effective. These control laws permit the introduction of aerodynamic damping and stiffness terms in accordance with the requirements of any specific system. Flutter suppression and gust alleviation problems can now be treated by either a trailing edge control system or by a leading edge-trailing edge control system by using the aerodynamic energy concept. Results are applicable to a wide class of aircraft operating at subsonic Mach numbers.

Optimal control theory investigation of proprotor/wing response to vertical gust

NASA Technical Reports Server (NTRS)

Frick, J. K. D.; Johnson, W.

1974-01-01

Optimal control theory is used to design linear state variable feedback to improve the dynamic characteristics of a rotor and cantilever wing representing the tilting proprotor aircraft in cruise flight. The response to a vertical gust and system damping are used as criteria for the open and closed loop performance. The improvement in the dynamic characteristics achievable is examined for a gimballed rotor and for a hingeless rotor design. Several features of the design process are examined, including: (1) using only the wing or only the rotor dynamics in the control system design; (2) the use of a wing flap as well as the rotor controls for inputs; (3) and the performance of the system designed for one velocity at other forward speeds.

A passive gust alleviation system for a light aircraft

NASA Technical Reports Server (NTRS)

Roesch, P.; Harlan, R. B.

1975-01-01

A passive aeromechanical gust alleviation system was examined for application to a Cessna 172. The system employs small auxiliary wings to sense changes in angle of attack and to drive the wing flaps to compensate the resulting incremental lift. The flaps also can be spring loaded to neutralize the effects of variations in dynamic pressure. Conditions for gust alleviation are developed and shown to introduce marginal stability if both vertical and horizontal gusts are compensated. Satisfactory behavior is realized if only vertical gusts are absorbed; however, elevator control is effectively negated by the system. Techniques to couple the elevator and flaps are demonstrated to restore full controllability without sacrifice of gust alleviation.

14 CFR 23.415 - Ground gust conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground gust conditions. 23.415 Section 23... and System Loads § 23.415 Ground gust conditions. (a) The control system must be investigated as follows for control surface loads due to ground gusts and taxiing downwind: (1) If an investigation of the...

Investigation of the atmospheric boundary layer characteristics on gust factor for the calculation of wind load

NASA Astrophysics Data System (ADS)

Ghanadi, Farzin; Emes, Matthew; Yu, Jeremy; Arjomandi, Maziar; Kelso, Richard

2017-06-01

Dynamic amplification and gust effects from turbulence can increase wind loads significantly over and above the static wind loads that have been used for heliostat design. This paper presents the results of analyzing the relationship between gust factor and turbulence intensity within the atmospheric boundary layer (ABL) based on the high fidelity measurements of wind velocity at the SLTEST facility in the Utah desert. Results showed that there are distinct characteristics of a low roughness ABL that deviate from semi-empirical relationships derived for open country and urban terrains with larger surface roughness heights. The analysis also indicated that gust factor is increased by 2.4% when lowering the gust period from 3s to 1s in the low roughness field experiment ABL, compared to a 3.6% increase in a suburban terrain at a 10m height. Although 3s gust periods are recommended in AS/NZS 1170.2 [1], comparison of gust factor data with a 1s gust period is recommended particularly in high roughness ABLs such as in urban areas, to ensure that buildings are adequately designed to withstand higher frequency gusts. This research proved the strength of the correlation between gust factor and turbulence intensity is dependent on the surface roughness height of the terrain. It is recommended that the coefficient in the previous semi-empirical equation must be adjusted to be fitted to the low roughness desert terrain in the field experiment ABL.

Project "Convective Wind Gusts" (ConWinG)

NASA Astrophysics Data System (ADS)

Mohr, Susanna; Richter, Alexandra; Kunz, Michael; Ruck, Bodo

2017-04-01

Convectively-driven strong winds usually associated with thunderstorms frequently cause substantial damage to buildings and other structures in many parts of the world. Decisive for the high damage potential are the short-term wind speed maxima with duration of a few seconds, termed as gusts. Several studies have shown that convectively-driven gusts can reach even higher wind speeds compared to turbulent gusts associated with synoptic-scale weather systems. Due to the small-scale and non-stationary nature of convective wind gusts, there is a considerable lack of knowledge regarding their characteristics and statistics. Furthermore, their interaction with urban structures and their influence on buildings is not yet fully understood. For these two reasons, convective wind events are not included in the present wind load standards of buildings and structures, which so far have been based solely on the characteristics of synoptically-driven wind gusts in the near-surface boundary layer (e. g., DIN EN 1991-1-4:2010-12; ASCE7). However, convective and turbulent gusts differ considerably, e.g. concerning vertical wind-speed profiles, gust factors (i.e., maximum to mean wind speed), or exceedance probability curves. In an effort to remedy this situation, the overarching objective of the DFG-project "Convective Wind Gusts" (ConWinG) is to investigate the characteristics and statistics of convective gusts as well as their interaction with urban structures. Based on a set of 110 climate stations of the German Weather Service (DWD) between 1992 and 2014, we analyzed the temporal and spatial distribution, intensity, and occurrence probability of convective gusts. Similar to thunderstorm activity, the frequency of convective gusts decreases gradually from South to North Germany. A relation between gust intensity/probability to orography or climate conditions cannot be identified. Rather, high wind speeds, e.g., above 30 m/s, can be expected everywhere in Germany with almost similar occurrence probabilities. A laboratory experiment with an impinging jet simulating the downdraft was performed to investigate the propagation of a gust within built environment. The aim is to investigate the interaction of the resulting convective gusts along the near-surface layers with different urban structures - from single street canyons up to more complex block array structures. It was shown that high velocities are conserved within street canyons over longer distances compared to open terrain conditions. In addition, the experiments revealed the ratio of building height to downdraft size as a crucial factor with regard to vertical velocities at roof level and the pressure distribution on the facades.

Validation of a High-Order Prefactored Compact Scheme on Nonlinear Flows with Complex Geometries

NASA Technical Reports Server (NTRS)

Hixon, Ray; Mankbadi, Reda R.; Povinelli, L. A. (Technical Monitor)

2000-01-01

Three benchmark problems are solved using a sixth-order prefactored compact scheme employing an explicit 10th-order filter with optimized fourth-order Runge-Kutta time stepping. The problems solved are the following: (1) propagation of sound waves through a transonic nozzle; (2) shock-sound interaction; and (3) single airfoil gust response. In the first two problems, the spatial accuracy of the scheme is tested on a stretched grid, and the effectiveness of boundary conditions is shown. The solution stability and accuracy near a shock discontinuity is shown as well. Also, 1-D nonlinear characteristic boundary conditions will be evaluated. In the third problem, a nonlinear Euler solver will be used that solves the equations in generalized curvilinear coordinates using the chain rule transformation. This work, continuing earlier work on flat-plate cascades and Joukowski airfoils, will focus mainly on the effect of the grid and boundary conditions on the accuracy of the solution. The grids were generated using a commercially available grid generator, GridPro/az3000.

On the relationship between matched filter theory as applied to gust loads and phased design loads analysis

NASA Technical Reports Server (NTRS)

Zeiler, Thomas A.; Pototzky, Anthony S.

1989-01-01

A theoretical basis and example calculations are given that demonstrate the relationship between the Matched Filter Theory approach to the calculation of time-correlated gust loads and Phased Design Load Analysis in common use in the aerospace industry. The relationship depends upon the duality between Matched Filter Theory and Random Process Theory and upon the fact that Random Process Theory is used in Phased Design Loads Analysis in determining an equiprobable loads design ellipse. Extensive background information describing the relevant points of Phased Design Loads Analysis, calculating time-correlated gust loads with Matched Filter Theory, and the duality between Matched Filter Theory and Random Process Theory is given. It is then shown that the time histories of two time-correlated gust load responses, determined using the Matched Filter Theory approach, can be plotted as parametric functions of time and that the resulting plot, when superposed upon the design ellipse corresponding to the two loads, is tangent to the ellipse. The question is raised of whether or not it is possible for a parametric load plot to extend outside the associated design ellipse. If it is possible, then the use of the equiprobable loads design ellipse will not be a conservative design practice in some circumstances.

Stresses Produced in Airplane Wings by Gusts

NASA Technical Reports Server (NTRS)

Kussner, Hans Georg

1932-01-01

Accurate prediction of gust stress being out of the question because of the multiplicity of the free air movements, the exploration of gust stress is restricted to static method which must be based upon: 1) stress measurements in free flight; 2) check of design specifications of approved type airplanes. With these empirical data the stress must be compared which can be computed for a gust of known intensity and structure. This "maximum gust" then must be so defined as to cover the whole ambit of empiricism and thus serve as prediction for new airplane designs.

The Flight of Flexible Aircraft in Turbulence - State-of-the-Art in the Description and Modelling of Atmospheric Turbulence: Meeting of the Structures and Materials Panel of AGARD (64th) Held in Athens (Greece) on 28 September-3 October 1986

DTIC Science & Technology

1987-12-01

not know that it has any real value or credibility. This situation suggests the following. Before the community at large can evaluate the SDG ...design approaches, such as the SDG method, are needed to handle the response of nonlinear subsystems--such as gust load alleviation. I wish to...observed in his SDG approach. Thus his result obtained from examining sequential discrete type gust is not too surprising, since It apparently can

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

14 CFR Appendix G to Part 25 - Continuous Gust Design Criteria

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Values of Ā (ratio of root-mean-square incremental load root-mean-square gust velocity) must be... gust velocity, ft./sec. Ω=reduced frequency, radians per foot. L=2,500 ft. (3) The limit loads must be... velocity Uσ: (i) At speed Vc: Uσ=85 fps true gust velocity in the interval 0 to 30,000 ft. altitude and is...

A numerical investigation of the airfoil-gust interaction noise in transonic flows: Acoustic processes

NASA Astrophysics Data System (ADS)

Zhong, Siyang; Zhang, Xin; Gill, James; Fattah, Ryu; Sun, Yuhao

2018-07-01

The sound produced by airfoil-gust interaction is a significant source of broadband noise in turbofan engines or contra-rotating open rotors (CRORs). There are competing mechanisms in this regime because of the presence of shocks that were seldom considered in the previous subsonic studies. A numerical investigation of airfoil-gust interaction noise at transonic speeds is undertaken in this work. By introducing vortical gust/synthetic turbulence to specified regions in the computational domain to interact with different elements in the flow field, it is shown that the dominant sound source is caused by leading edge-gust interaction. It is demonstrated that both streamwise and transverse disturbances interact with the near-field non-uniform mean flow and shocks can produce sound using a local gust injection method. The propagation of sound is significantly influenced by the presence of the shocks, and the far field radiation pattern is changed. We also study the effect of gust strength on the near and far field properties. The linearity is maintained for gust strength smaller than 1.0% of the mean flow velocity. Otherwise, the shocks may experience oscillations that will alter the near-field aerodynamics and far-field radiation.

Coherent Lidar Turbulence Measurement for Gust Load Alleviation

NASA Technical Reports Server (NTRS)

Bogue, Rodney K.; Ehernberger, L. J.; Soreide, David; Bagley, Hal

1996-01-01

Atmospheric turbulence adversely affects operation of commercial and military aircraft and is a design constraint. The airplane structure must be designed to survive the loads imposed by turbulence. Reducing these loads allows the airplane structure to be lighter, a substantial advantage for a commercial airplane. Gust alleviation systems based on accelerometers mounted in the airplane can reduce the maximum gust loads by a small fraction. These systems still represent an economic advantage. The ability to reduce the gust load increases tremendously if the turbulent gust can be measured before the airplane encounters it. A lidar system can make measurements of turbulent gusts ahead of the airplane, and the NASA Airborne Coherent Lidar for Advanced In-Flight Measurements (ACLAIM) program is developing such a lidar. The ACLAIM program is intended to develop a prototype lidar system for use in feasibility testing of gust load alleviation systems and other airborne lidar applications, to define applications of lidar with the potential for improving airplane performance, and to determine the feasibility and benefits of these applications. This paper gives an overview of the ACLAIM program, describes the lidar architecture for a gust alleviation system, and describes the prototype ACLAIM lidar system.

A Comprehensive Robust Adaptive Controller for Gust Load Alleviation

PubMed Central

Quagliotti, Fulvia

2014-01-01

The objective of this paper is the implementation and validation of an adaptive controller for aircraft gust load alleviation. The contribution of this paper is the design of a robust controller that guarantees the reduction of the gust loads, even when the nominal conditions change. Some preliminary results are presented, considering the symmetric aileron deflection as control device. The proposed approach is validated on subsonic transport aircraft for different mass and flight conditions. Moreover, if the controller parameters are tuned for a specific gust model, even if the gust frequency changes, no parameter retuning is required. PMID:24688411

Inlet Guide Vane Wakes Including Rotor Effects

NASA Astrophysics Data System (ADS)

Johnston, R. T.; Fleeter, S.

2001-02-01

Fundamental experiments are described directed at the investigation of forcing functions generated by an inlet guide vane (IGV) row, including interactions with the downstream rotor, for application to turbomachine forced response design systems. The experiments are performed in a high-speed research fan facility comprised of an IGV row upstream of a rotor. IGV-rotor axial spacing is variable, with the IGV row able to be indexed circumferentially, thereby allowing measurements to be made across several IGV wakes. With an IGV relative Mach number of 0.29, measurements include the IGV wake pressure and velocity fields for three IGV-rotor axial spacings. The decay characteristics of the IGV wakes are compared to the Majjigi and Gliebe empirical correlations. After Fourier decomposition, a vortical-potential gust splitting analysis is implemented to determine the vortical and potential harmonic wake gust forcing functions both upstream and downstream of the rotor. Higher harmonics of the vortical gust component of the IGV wakes are found to decay at a uniform rate due to viscous diffusion.

Implementation of a gust front head collapse scheme in the WRF numerical model

NASA Astrophysics Data System (ADS)

Lompar, Miloš; Ćurić, Mladjen; Romanic, Djordje

2018-05-01

Gust fronts are thunderstorm-related phenomena usually associated with severe winds which are of great importance in theoretical meteorology, weather forecasting, cloud dynamics and precipitation, and wind engineering. An important feature of gust fronts demonstrated through both theoretical and observational studies is the periodic collapse and rebuild of the gust front head. This cyclic behavior of gust fronts results in periodic forcing of vertical velocity ahead of the parent thunderstorm, which consequently influences the storm dynamics and microphysics. This paper introduces the first gust front pulsation parameterization scheme in the WRF-ARW model (Weather Research and Forecasting-Advanced Research WRF). The influence of this new scheme on model performances is tested through investigation of the characteristics of an idealized supercell cumulonimbus cloud, as well as studying a real case of thunderstorms above the United Arab Emirates. In the ideal case, WRF with the gust front scheme produced more precipitation and showed different time evolution of mixing ratios of cloud water and rain, whereas the mixing ratios of ice and graupel are almost unchanged when compared to the default WRF run without the parameterization of gust front pulsation. The included parameterization did not disturb the general characteristics of thunderstorm cloud, such as the location of updraft and downdrafts, and the overall shape of the cloud. New cloud cells in front of the parent thunderstorm are also evident in both ideal and real cases due to the included forcing of vertical velocity caused by the periodic collapse of the gust front head. Despite some differences between the two WRF simulations and satellite observations, the inclusion of the gust front parameterization scheme produced more cumuliform clouds and seem to match better with real observations. Both WRF simulations gave poor results when it comes to matching the maximum composite radar reflectivity from radar measurement. Similar to the ideal case, WRF model with the gust front scheme gave more precipitation than the default WRF run. In particular, the gust front scheme increased the area characterized with light precipitation and diminished the development of very localized and intense precipitation.

Gust prediction via artificial hair sensor array and neural network

NASA Astrophysics Data System (ADS)

Pankonien, Alexander M.; Thapa Magar, Kaman S.; Beblo, Richard V.; Reich, Gregory W.

2017-04-01

Gust Load Alleviation (GLA) is an important aspect of flight dynamics and control that reduces structural loadings and enhances ride quality. In conventional GLA systems, the structural response to aerodynamic excitation informs the control scheme. A phase lag, imposed by inertia, between the excitation and the measurement inherently limits the effectiveness of these systems. Hence, direct measurement of the aerodynamic loading can eliminate this lag, providing valuable information for effective GLA system design. Distributed arrays of Artificial Hair Sensors (AHS) are ideal for surface flow measurements that can be used to predict other necessary parameters such as aerodynamic forces, moments, and turbulence. In previous work, the spatially distributed surface flow velocities obtained from an array of artificial hair sensors using a Single-State (or feedforward) Neural Network were found to be effective in estimating the steady aerodynamic parameters such as air speed, angle of attack, lift and moment coefficient. This paper extends the investigation of the same configuration to unsteady force and moment estimation, which is important for active GLA control design. Implementing a Recurrent Neural Network that includes previous-timestep sensor information, the hair sensor array is shown to be capable of capturing gust disturbances with a wide range of periods, reducing predictive error in lift and moment by 68% and 52% respectively. The L2 norms of the first layer of the weight matrices were compared showing a 23% emphasis on prior versus current information. The Recurrent architecture also improves robustness, exhibiting only a 30% increase in predictive error when undertrained as compared to a 170% increase by the Single-State NN. This diverse, localized information can thus be directly implemented into a control scheme that alleviates the gusts without waiting for a structural response or requiring user-intensive sensor calibration.

Single-Point Attachment Wind Damper for Launch Vehicle On-Pad Motion

NASA Technical Reports Server (NTRS)

Hrinda, Glenn A.

2009-01-01

A single-point-attachment wind-damper device is proposed to reduce on-pad motion of a cylindrical launch vehicle. The device is uniquely designed to attach at only one location along the vehicle and capable of damping out wind gusts from any lateral direction. The only source of damping is from two viscous dampers in the device. The effectiveness of the damper design in reducing vehicle displacements is determined from transient analysis results using an Ares I-X launch vehicle. Combinations of different spring stiffnesses and damping are used to show how the vehicle's displacement response is significantly reduced during a wind gust.

Information retrieval from wide-band meteorological data - An example

NASA Technical Reports Server (NTRS)

Adelfang, S. I.; Smith, O. E.

1983-01-01

The methods proposed by Smith and Adelfang (1981) and Smith et al. (1982) are used to calculate probabilities over rectangles and sectors of the gust magnitude-gust length plane; probabilities over the same regions are also calculated from the observed distributions and a comparison is also presented to demonstrate the accuracy of the statistical model. These and other statistical results are calculated from samples of Jimsphere wind profiles at Cape Canaveral. The results are presented for a variety of wavelength bands, altitudes, and seasons. It is shown that wind perturbations observed in Jimsphere wind profiles in various wavelength bands can be analyzed by using digital filters. The relationship between gust magnitude and gust length is modeled with the bivariate gamma distribution. It is pointed out that application of the model to calculate probabilities over specific areas of the gust magnitude-gust length plane can be useful in aerospace design.

Unsteady loading on an airfoil of arbitrary thickness

NASA Astrophysics Data System (ADS)

Glegg, Stewart A. L.; Devenport, William

2009-01-01

The unsteady loading on an airfoil of arbitrary thickness is evaluated by using the generalized form of Blasius theorem and a conformal mapping that maps the airfoil surface onto a circle. For a blade vortex interaction the results show that the time history of the unsteady loading is determined by the passage of the vortex relative to the leading edge singularity in the circle plane. The singularity lies inside the circle and moves to a smaller radius as the thickness is increased, causing the unsteady loading pulse to be smoothed. The effect of angle of attack is to move the stagnation point relative to the leading edge singularity and this significantly increases the unsteady lift if the vortex passes on the suction side of the airfoil. These characteristics are different for a step upwash gust, which is considered as a simplified model of a large scale turbulent gust. It is shown that the time history of the magnitude of the unsteady loading is almost completely unaltered by angle of attack for the step gust, but it's direction of action rotates forward by an angle equal to the angle of attack, extending an earlier result by Howe for a flat plate in a turbulent flow to airfoils of arbitrary thickness. However spectral analysis of the gust shows that the high frequency blade response is reduced as the thickness of the airfoil is increased.

Unsteady lift forces on highly cambered airfoils moving through a gust

NASA Technical Reports Server (NTRS)

Atassi, H.; Goldstein, M.

1974-01-01

An unsteady airfoil theory in which the flow is linearized about the steady potential flow of the airfoil is presented. The theory is applied to an airfoil entering a gust. After transformation to the W-plane, the problem is formulated in terms of a Poisson's equation. The solutions are expanded in a Fourier-Bessel series. The theory is applied to a circular arc with arbitrary camber. Closed form expressions for the velocity and pressure on the surface of the airfoil are obtained. The unsteady aerodynamic forces are then calculated and shown to contain two terms. One in an explicit closed analytical form represents the contribution of the oncoming vortical disturbance, the other depends on a single quadrature and accounts for the effect of the wake.

A study of large scale gust generation in a small scale atmospheric wind tunnel with applications to Micro Aerial Vehicles

NASA Astrophysics Data System (ADS)

Roadman, Jason Markos

Modern technology operating in the atmospheric boundary layer can always benefit from more accurate wind tunnel testing. While scaled atmospheric boundary layer tunnels have been well developed, tunnels replicating portions of the atmospheric boundary layer turbulence at full scale are a comparatively new concept. Testing at full-scale Reynolds numbers with full-scale turbulence in an "atmospheric wind tunnel" is sought. Many programs could utilize such a tool including Micro Aerial Vehicle(MAV) development, the wind energy industry, fuel efficient vehicle design, and the study of bird and insect flight, to name just a few. The small scale of MAVs provide the somewhat unique capability of full scale Reynolds number testing in a wind tunnel. However, that same small scale creates interactions under real world flight conditions, atmospheric gusts for example, that lead to a need for testing under more complex flows than the standard uniform flow found in most wind tunnels. It is for these reasons that MAVs are used as the initial testing application for the atmospheric gust tunnel. An analytical model for both discrete gusts and a continuous spectrum of gusts is examined. Then, methods for generating gusts in agreement with that model are investigated. Previously used methods are reviewed and a gust generation apparatus is designed. Expected turbulence and gust characteristics of this apparatus are compared with atmospheric data. The construction of an active "gust generator" for a new atmospheric tunnel is reviewed and the turbulence it generates is measured utilizing single and cross hot wires. Results from this grid are compared to atmospheric turbulence and it is shown that various gust strengths can be produced corresponding to weather ranging from calm to quite gusty. An initial test is performed in the atmospheric wind tunnel whereby the effects of various turbulence conditions on transition and separation on the upper surface of a MAV wing is investigated using the surface oil flow visualization technique.

Analysis of Acceleration, Airspeed, and Gust-Velocity Data From a Four-Engine Transport Airplane Operating Over a Northwestern United States Alaska Route

NASA Technical Reports Server (NTRS)

Engel, Jerome N.; Copp, Martin R.

1959-01-01

Acceleration, airspeed, and altitude data obtained with an NACA VGH recorder from a four-engine commercial transport airplane operating over a northwestern United States-Alaska route were evaluated to determine the magnitude and frequency of occurrence of gust and maneuver accelerations., operating airspeeds, and gust velocities. The results obtained were then compared with the results previously reported in NACA Technical Note 3475 for two similar airplanes operating over transcontinental routes in the United States. No large variations in the gust experience for the three operations were noted. The results indicate that the gust-load experience of the present operation closely approximated that of the central transcontinental route in the United States with which it is compared and showed differences of about 4 to 1 when compared with that of the southern transcontinental route in the United States. In general, accelerations due to gusts occurred much more frequently than those due to operational maneuvers. At a measured normal-acceleration increment of 0.5g, accelerations due to gusts occurred roughly 35 times more frequently than those due to operational maneuvers.

Summary of Information Relating to Gust Loads on Airplanes

NASA Technical Reports Server (NTRS)

Donely, Philip

1950-01-01

Available information on gust structure, airplane reactions, and pertinent operating statistics has been examined. This report attempts to coordinate this information with reference to the prediction of gust loads on airplanes. The material covered represents research up to October 1947. (author)

14 CFR 27.341 - Gust loads.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Gust loads. 27.341 Section 27.341 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Flight Loads § 27.341 Gust loads. The rotorcraft...

14 CFR 27.341 - Gust loads.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Gust loads. 27.341 Section 27.341 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: NORMAL CATEGORY ROTORCRAFT Strength Requirements Flight Loads § 27.341 Gust loads. The rotorcraft...

A Wind-Tunnel Investigation of Tilt-Rotor Gust Alleviation Systems

NASA Technical Reports Server (NTRS)

Ham, N. D.; Whitaker, H. P.

1978-01-01

The alleviation of the effects of gusts on tilt rotor aircraft by means of active control systems was investigated. The gust generator, the derivation of the equations of motion of the rotor wing combination, the correlation of these equations with the results of wind tunnel model tests, the use of the equations to design various gust alleviating active control systems, and the testing and evaluation of these control systems by means of wind tunnel model tests were developed.

Gusts and Shear in an Idealized LES-modeled Hurricane

NASA Astrophysics Data System (ADS)

Worsnop, R.; Lundquist, J. K.; Bryan, G. H.; Damiani, R.; Musial, W.

2016-12-01

Tropical cyclone winds can cause extreme loading and damage to coastal structures such as buildings and energy infrastructure. Offshore wind energy development is underway along the US East Coast where hurricanes pose a substantial risk. Understanding wind gusts, gust factor, shear, and veer in the hurricane boundary layer (HBL) can help manufacturers assess risk and design wind turbines to better withstand these extreme wind conditions. Because of the paucity of observational data at low-levels (200 m and below), we use the Cloud Model Version I (CM1) large-eddy simulation numerical model to simulate high spatial- (10 m) and temporal- (0.1 s) resolution data. This unique dataset is used to answer the following questions: do severe mean wind speeds and gusts that exceed current design limits occur?; how does the gust factor vary with distance from the eye?; and lastly, how does wind direction vary horizontally and with height? We find that mean winds and gusts near the eyewall can exceed current turbine design thresholds of 50 m s-1 and 70 m s-1, respectively. Gust factors are greatest at the eye-eyewall interface just inward of the peak gust location and can exceed the 1.4 value used to convert a 50 m s-1 reference wind speed to a 50-year 3-second gust. Strong veer (15-30 degrees) across a 120 m-layer suggests that veer should be assessed against standard design prescriptions. Lastly, wind directions can shift 10-25 degrees in durations shorter than 10 minutes, which can challenge structures designed to endure winds from a consistent direction for periods longer than 10 minutes, including wind turbines.

The passage of an infinite swept airfoil through an oblique gust. [approximate solution for aerodynamic response

NASA Technical Reports Server (NTRS)

Adamczyk, J. L.

1974-01-01

An approximate solution is reported for the unsteady aerodynamic response of an infinite swept wing encountering a vertical oblique gust in a compressible stream. The approximate expressions are of closed form and do not require excessive computer storage or computation time, and further, they are in good agreement with the results of exact theory. This analysis is used to predict the unsteady aerodynamic response of a helicopter rotor blade encountering the trailing vortex from a previous blade. Significant effects of three dimensionality and compressibility are evident in the results obtained. In addition, an approximate solution for the unsteady aerodynamic forces associated with the pitching or plunging motion of a two dimensional airfoil in a subsonic stream is presented. The mathematical form of this solution approaches the incompressible solution as the Mach number vanishes, the linear transonic solution as the Mach number approaches one, and the solution predicted by piston theory as the reduced frequency becomes large.

Development and application of an optimization procedure for flutter suppression using the aerodynamic energy concept

NASA Technical Reports Server (NTRS)

Nissim, E.; Abel, I.

1978-01-01

An optimization procedure is developed based on the responses of a system to continuous gust inputs. The procedure uses control law transfer functions which have been partially determined by using the relaxed aerodynamic energy approach. The optimization procedure yields a flutter suppression system which minimizes control surface activity in a gust environment. The procedure is applied to wing flutter of a drone aircraft to demonstrate a 44 percent increase in the basic wing flutter dynamic pressure. It is shown that a trailing edge control system suppresses the flutter instability over a wide range of subsonic mach numbers and flight altitudes. Results of this study confirm the effectiveness of the relaxed energy approach.

Robust control of drag and lateral dynamic response for road vehicles exposed to cross-wind gusts

NASA Astrophysics Data System (ADS)

Pfeiffer, Jens; King, Rudibert

2018-03-01

A robust closed-loop active flow control strategy for road vehicles under unsteady cross-wind conditions is presented. It is designed based on black-box models identified from experimental data for a 3D bluff body equipped with Coanda actuators along the rear edges. The controller adjusts the blowing rates of the actuators individually, achieving a drag reduction of about 15% while simultaneously improving cross-wind sensitivity. Hereby, the lateral vehicle dynamics and driver behavior are taken into account and replicated in the wind tunnel via a novel model support system. The effectiveness of the control strategy is demonstrated via cross-wind gust experiments.

Technology Integration (Task 20) Aeroservoelastic Modeling and Design Studies. Part A; Evaluation of Aeroservoelastic Effects on Flutter and Dynamic Gust Response

NASA Technical Reports Server (NTRS)

Nagaraja, K. S.; Kraft, R. H.

1999-01-01

The HSCT Flight Controls Group has developed longitudinal control laws, utilizing PTC aeroelastic flexible models to minimize aeroservoelastic interaction effects, for a number of flight conditions. The control law design process resulted in a higher order controller and utilized a large number of sensors distributed along the body for minimizing the flexibility effects. Processes were developed to implement these higher order control laws for performing the dynamic gust loads and flutter analyses. The processes and its validation were documented in Reference 2, for selected flight condition. The analytical results for additional flight conditions are presented in this document for further validation.

14 CFR 25.679 - Control system gust locks.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.679 Control system gust locks. (a) There must be a device to prevent damage to the control surfaces (including tabs... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Control system gust locks. 25.679 Section...

14 CFR 25.679 - Control system gust locks.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.679 Control system gust locks. (a) There must be a device to prevent damage to the control surfaces (including tabs... 14 Aeronautics and Space 1 2012-01-01 2012-01-01 false Control system gust locks. 25.679 Section...

14 CFR 25.679 - Control system gust locks.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.679 Control system gust locks. (a) There must be a device to prevent damage to the control surfaces (including tabs... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Control system gust locks. 25.679 Section...

14 CFR 25.679 - Control system gust locks.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.679 Control system gust locks. (a) There must be a device to prevent damage to the control surfaces (including tabs... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Control system gust locks. 25.679 Section...

14 CFR 25.415 - Ground gust conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ground gust conditions. 25.415 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads § 25.415 Ground... ground gusts and taxiing downwind: (1) The control system between the stops nearest the surfaces and the...

14 CFR 25.415 - Ground gust conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground gust conditions. 25.415 Section 25... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads § 25.415 Ground... ground gusts and taxiing downwind: (1) The control system between the stops nearest the surfaces and the...

Observational Constraints on Ephemeral Wind Gusts that MobilizeSoil Dust Aerosols

NASA Astrophysics Data System (ADS)

Miller, R. L.; Leung, M. F.

2017-12-01

Dust aerosol models resolve the planetary scale winds that disperse particles throughout the globe, but the winds raising dust are often organized on smaller scales that are below the resolution of the model. These winds, including ephemeral wind gusts associated with boundary layer mixing, are typically parameterized. For example, gusts by dry convective eddies are related to the sensible heat flux. What remains is to constrain the magnitude of the wind gusts using boundary layer measurements, so that dust emission has the correct sensitivity to these gusts, relative to the resolved wind. Here, we use a year of ARM measurements with high temporal resolution from Niamey, Niger in the Sahel to evaluate our parameterization. This evaluation is important for dust aerosol models that use 'nudging' to reproduce observed transport patterns.

Variation of the low level winds during the passage of a thunderstorm gust front

NASA Technical Reports Server (NTRS)

Sinclair, R. W.; Anthes, R. A.; Panofsky, H. A.

1973-01-01

Three time histories of wind profiles in thunderstorm gust fronts at Cape Kennedy and three at Oklahoma City are analyzed. Wind profiles at maximum wind strength below 100 m follow logarithmic laws, so that winds above the surface layer can be estimated from surface winds once the roughness length is known. A statistical analysis of 81 cases of surface winds during thunderstorms at Tampa revealed no predictor with skill to predict the time of maximum gust. Some 34% of the variance of the strength of the gust is accounted for by a stability index and surface wind prior to the gust; the regression equations for these variables are given. The coherence between microscale wind speed variations at the different levels has the same proportions as in non-thunderstorm cases.

Development of Aeroservoelastic Analytical Models and Gust Load Alleviation Control Laws of a SensorCraft Wind-Tunnel Model Using Measured Data

NASA Technical Reports Server (NTRS)

Silva, Walter A.; Vartio, Eric; Shimko, Anthony; Kvaternik, Raymond G.; Eure, Kenneth W.; Scott,Robert C.

2007-01-01

Aeroservoelastic (ASE) analytical models of a SensorCraft wind-tunnel model are generated using measured data. The data was acquired during the ASE wind-tunnel test of the HiLDA (High Lift-to-Drag Active) Wing model, tested in the NASA Langley Transonic Dynamics Tunnel (TDT) in late 2004. Two time-domain system identification techniques are applied to the development of the ASE analytical models: impulse response (IR) method and the Generalized Predictive Control (GPC) method. Using measured control surface inputs (frequency sweeps) and associated sensor responses, the IR method is used to extract corresponding input/output impulse response pairs. These impulse responses are then transformed into state-space models for use in ASE analyses. Similarly, the GPC method transforms measured random control surface inputs and associated sensor responses into an AutoRegressive with eXogenous input (ARX) model. The ARX model is then used to develop the gust load alleviation (GLA) control law. For the IR method, comparison of measured with simulated responses are presented to investigate the accuracy of the ASE analytical models developed. For the GPC method, comparison of simulated open-loop and closed-loop (GLA) time histories are presented.

Development of Aeroservoelastic Analytical Models and Gust Load Alleviation Control Laws of a SensorCraft Wind-Tunnel Model Using Measured Data

NASA Technical Reports Server (NTRS)

Silva, Walter A.; Shimko, Anthony; Kvaternik, Raymond G.; Eure, Kenneth W.; Scott, Robert C.

2006-01-01

Aeroservoelastic (ASE) analytical models of a SensorCraft wind-tunnel model are generated using measured data. The data was acquired during the ASE wind-tunnel test of the HiLDA (High Lift-to-Drag Active) Wing model, tested in the NASA Langley Transonic Dynamics Tunnel (TDT) in late 2004. Two time-domain system identification techniques are applied to the development of the ASE analytical models: impulse response (IR) method and the Generalized Predictive Control (GPC) method. Using measured control surface inputs (frequency sweeps) and associated sensor responses, the IR method is used to extract corresponding input/output impulse response pairs. These impulse responses are then transformed into state-space models for use in ASE analyses. Similarly, the GPC method transforms measured random control surface inputs and associated sensor responses into an AutoRegressive with eXogenous input (ARX) model. The ARX model is then used to develop the gust load alleviation (GLA) control law. For the IR method, comparison of measured with simulated responses are presented to investigate the accuracy of the ASE analytical models developed. For the GPC method, comparison of simulated open-loop and closed-loop (GLA) time histories are presented.

Statistical Downscaling of Gusts During Extreme European Winter Storms Using Radial-Basis-Function Networks

NASA Astrophysics Data System (ADS)

Voigt, M.; Lorenz, P.; Kruschke, T.; Osinski, R.; Ulbrich, U.; Leckebusch, G. C.

2012-04-01

Winterstorms and related gusts can cause extensive socio-economic damages. Knowledge about the occurrence and the small scale structure of such events may help to make regional estimations of storm losses. For a high spatial and temporal representation, the use of dynamical downscaling methods (RCM) is a cost-intensive and time-consuming option and therefore only applicable for a limited number of events. The current study explores a methodology to provide a statistical downscaling, which offers small scale structured gust fields from an extended large scale structured eventset. Radial-basis-function (RBF) networks in combination with bidirectional Kohonen (BDK) maps are used to generate the gustfields on a spatial resolution of 7 km from the 6-hourly mean sea level pressure field from ECMWF reanalysis data. BDK maps are a kind of neural network which handles supervised classification problems. In this study they are used to provide prototypes for the RBF network and give a first order approximation for the output data. A further interpolation is done by the RBF network. For the training process the 50 most extreme storm events over the North Atlantic area from 1957 to 2011 are used, which have been selected from ECMWF reanalysis datasets ERA40 and ERA-Interim by an objective wind based tracking algorithm. These events were downscaled dynamically by application of the DWD model chain GME → COSMO-EU. Different model parameters and their influence on the quality of the generated high-resolution gustfields are studied. It is shown that the statistical RBF network approach delivers reasonable results in modeling the regional gust fields for untrained events.

Energy extraction from atmospheric turbulence to improve flight vehicle performance

NASA Astrophysics Data System (ADS)

Patel, Chinmay Karsandas

Small 'bird-sized' Unmanned Aerial Vehicles (UAVs) have now become practical due to technological advances in embedded electronics, miniature sensors and actuators, and propulsion systems. Birds are known to take advantage of wind currents to conserve energy and fly long distances without flapping their wings. This dissertation explores the possibility of improving the performance of small UAVs by extracting the energy available in atmospheric turbulence. An aircraft can gain energy from vertical gusts by increasing its lift in regions of updraft and reducing its lift in downdrafts - a concept that has been known for decades. Starting with a simple model of a glider flying through a sinusoidal gust, a parametric optimization approach is used to compute the minimum gust amplitude and optimal control input required for the glider to sustain flight without losing energy. For small UAVs using optimal control inputs, sinusoidal gusts with amplitude of 10--15% of the cruise speed are sufficient to keep the aircraft aloft. The method is then modified and extended to include random gusts that are representative of natural turbulence. A procedure to design optimal control laws for energy extraction from realistic gust profiles is developed using a Genetic Algorithm (GA). A feedback control law is designed to perform well over a variety of random gusts, and not be tailored for one particular gust. A small UAV flying in vertical turbulence is shown to obtain average energy savings of 35--40% with the use of a simple control law. The design procedure is also extended to determine optimal control laws for sinusoidal as well as turbulent lateral gusts. The theoretical work is complemented by experimental validation using a small autonomous UAV. The development of a lightweight autopilot and UAV platform is presented. Flight test results show that active control of the lift of an autonomous glider resulted in approximately 46% average energy savings compared to glides with fixed control surfaces. Statistical analysis of test samples shows that 19% of the active control test runs resulted in no energy loss, thus demonstrating the potential of the 'gust soaring' concept to dramatically improve the performance of small UAVs.

Extreme Vertical Gusts in the Atmospheric Boundary Layer

DTIC Science & Technology

2015-07-01

significant effect on the statistics of the rare, extreme gusts. In the lowest 5,000 ft, boundary layer effects make small to moderate vertical...4 2.4 Effects of Gust Shape ............................................................................................... 5... Definitions Adiabatic Lapse Rate The rate of change of temperature with altitude that would occur if a parcel of air was transported sufficiently

14 CFR 23.415 - Ground gust conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... and System Loads § 23.415 Ground gust conditions. (a) The control system must be investigated as... control system for ground gust loads is not required by paragraph (a)(2) of this section, but the applicant elects to design a part of the control system of these loads, these loads need only be carried...

14 CFR 25.345 - High lift devices.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.345 High lift... level flight. Gust loads resulting on each part of the structure must be determined by rational analysis... prescribed in § 25.337(b); and (2) The discrete vertical gust criteria in § 25.341(a). (d) The airplane must...

14 CFR 25.345 - High lift devices.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.345 High lift... level flight. Gust loads resulting on each part of the structure must be determined by rational analysis... prescribed in § 25.337(b); and (2) The discrete vertical gust criteria in § 25.341(a). (d) The airplane must...

14 CFR 25.345 - High lift devices.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.345 High lift... level flight. Gust loads resulting on each part of the structure must be determined by rational analysis... prescribed in § 25.337(b); and (2) The discrete vertical gust criteria in § 25.341(a). (d) The airplane must...

14 CFR 23.341 - Gust loads factors.

Code of Federal Regulations, 2014 CFR

2014-01-01

... loads factors. (a) Each airplane must be designed to withstand loads on each lifting surface resulting...=airplane mass ratio; U de=Derived gust velocities referred to in § 23.333(c) (f.p.s.); ρ=Density of air... C NA per radian if the gust loads are applied to the wings and horizontal tail surfaces...

14 CFR 23.341 - Gust loads factors.

Code of Federal Regulations, 2012 CFR

2012-01-01

... loads factors. (a) Each airplane must be designed to withstand loads on each lifting surface resulting...=airplane mass ratio; U de=Derived gust velocities referred to in § 23.333(c) (f.p.s.); ρ=Density of air... C NA per radian if the gust loads are applied to the wings and horizontal tail surfaces...

14 CFR 23.341 - Gust loads factors.

Code of Federal Regulations, 2013 CFR

2013-01-01

... loads factors. (a) Each airplane must be designed to withstand loads on each lifting surface resulting...=airplane mass ratio; U de=Derived gust velocities referred to in § 23.333(c) (f.p.s.); ρ=Density of air... C NA per radian if the gust loads are applied to the wings and horizontal tail surfaces...

14 CFR 23.341 - Gust loads factors.

Code of Federal Regulations, 2011 CFR

2011-01-01

... loads factors. (a) Each airplane must be designed to withstand loads on each lifting surface resulting...=airplane mass ratio; U de=Derived gust velocities referred to in § 23.333(c) (f.p.s.); ρ=Density of air... C NA per radian if the gust loads are applied to the wings and horizontal tail surfaces...

Towards spatially constrained gust models

NASA Astrophysics Data System (ADS)

Bos, René; Bierbooms, Wim; van Bussel, Gerard

2014-06-01

With the trend of moving towards 10-20 MW turbines, rotor diameters are growing beyond the size of the largest turbulent structures in the atmospheric boundary layer. As a consequence, the fully uniform transients that are commonly used to predict extreme gust loads are losing their connection to reality and may lead to gross overdimensioning. More suiting would be to represent gusts by advecting air parcels and posing certain physical constraints on size and position. However, this would introduce several new degrees of freedom that significantly increase the computational burden of extreme load prediction. In an attempt to elaborate on the costs and benefits of such an approach, load calculations were done on the DTU 10 MW reference turbine where a single uniform gust shape was given various spatial dimensions with the transverse wavelength ranging up to twice the rotor diameter (357 m). The resulting loads displayed a very high spread, but remained well under the level of a uniform gust. Moving towards spatially constrained gust models would therefore yield far less conservative, though more realistic predictions at the cost of higher computation time.

Research and Applications in Aeroelasticity and Structural Dynamics at the NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Abel, Irving

1997-01-01

An overview of recently completed programs in aeroelasticity and structural dynamics research at the NASA Langley Research Center is presented. Methods used to perform flutter clearance studies in the wind-tunnel on a high performance fighter are discussed. Recent advances in the use of smart structures and controls to solve aeroelastic problems, including flutter and gust response are presented. An aeroelastic models program designed to support an advanced high speed civil transport is described. An extension to transonic small disturbance theory that better predicts flows involving separation and reattachment is presented. The results of a research study to determine the effects of flexibility on the taxi and takeoff characteristics of a high speed civil transport are presented. The use of photogrammetric methods aboard Space Shuttle to measure spacecraft dynamic response is discussed. Issues associated with the jitter response of multi-payload spacecraft are discussed. Finally a Space Shuttle flight experiment that studied the control of flexible spacecraft is described.

An analysis of life expectancy of airplane wings in normal cruising flight

NASA Technical Reports Server (NTRS)

Putnam, Abbott A

1945-01-01

In order to provide a basis for judging the relative importance of wing failure by fatigue and by single intense gusts, an analysis of wing life for normal cruising flight was made based on data on the frequency of atmospheric gusts. The independent variables considered in the analysis included stress-concentration factor, stress-load relation, wing loading, design and cruising speeds, design gust velocity, and airplane size. Several methods for estimating fatigue life from gust frequencies are discussed. The procedure selected for the analysis is believed to be simple and reasonably accurate, though slightly conservative.

Multi-Objective Flight Control for Drag Minimization and Load Alleviation of High-Aspect Ratio Flexible Wing Aircraft

NASA Technical Reports Server (NTRS)

Nguyen, Nhan; Ting, Eric; Chaparro, Daniel; Drew, Michael; Swei, Sean

2017-01-01

As aircraft wings become much more flexible due to the use of light-weight composites material, adverse aerodynamics at off-design performance can result from changes in wing shapes due to aeroelastic deflections. Increased drag, hence increased fuel burn, is a potential consequence. Without means for aeroelastic compensation, the benefit of weight reduction from the use of light-weight material could be offset by less optimal aerodynamic performance at off-design flight conditions. Performance Adaptive Aeroelastic Wing (PAAW) technology can potentially address these technical challenges for future flexible wing transports. PAAW technology leverages multi-disciplinary solutions to maximize the aerodynamic performance payoff of future adaptive wing design, while addressing simultaneously operational constraints that can prevent the optimal aerodynamic performance from being realized. These operational constraints include reduced flutter margins, increased airframe responses to gust and maneuver loads, pilot handling qualities, and ride qualities. All of these constraints while seeking the optimal aerodynamic performance present themselves as a multi-objective flight control problem. The paper presents a multi-objective flight control approach based on a drag-cognizant optimal control method. A concept of virtual control, which was previously introduced, is implemented to address the pair-wise flap motion constraints imposed by the elastomer material. This method is shown to be able to satisfy the constraints. Real-time drag minimization control is considered to be an important consideration for PAAW technology. Drag minimization control has many technical challenges such as sensing and control. An initial outline of a real-time drag minimization control has already been developed and will be further investigated in the future. A simulation study of a multi-objective flight control for a flight path angle command with aeroelastic mode suppression and drag minimization demonstrates the effectiveness of the proposed solution. In-flight structural loads are also an important consideration. As wing flexibility increases, maneuver load and gust load responses can be significant and therefore can pose safety and flight control concerns. In this paper, we will extend the multi-objective flight control framework to include load alleviation control. The study will focus initially on maneuver load minimization control, and then subsequently will address gust load alleviation control in future work.

14 CFR 23.341 - Gust loads factors.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Gust loads factors. 23.341 Section 23.341... loads factors. (a) Each airplane must be designed to withstand loads on each lifting surface resulting... criteria of § 23.333(c). (c) In the absence of a more rational analysis, the gust load factors must be...

Numerical solutions of the linearized Euler equations for unsteady vortical flows around lifting airfoils

NASA Technical Reports Server (NTRS)

Scott, James R.; Atassi, Hafiz M.

1990-01-01

A linearized unsteady aerodynamic analysis is presented for unsteady, subsonic vortical flows around lifting airfoils. The analysis fully accounts for the distortion effects of the nonuniform mean flow on the imposed vortical disturbances. A frequency domain numerical scheme which implements this linearized approach is described, and numerical results are presented for a large variety of flow configurations. The results demonstrate the effects of airfoil thickness, angle of attack, camber, and Mach number on the unsteady lift and moment of airfoils subjected to periodic vortical gusts. The results show that mean flow distortion can have a very strong effect on the airfoil unsteady response, and that the effect depends strongly upon the reduced frequency, Mach number, and gust wave numbers.

The effects of gusts on the fluctuating airloads of airfoils in transonic flow

NASA Technical Reports Server (NTRS)

Mccroskey, W. J.

1984-01-01

Unsteady interactions of distributed and sharp-edged gusts with a stationary airfoil have been analyzed in two-dimensional transonic flow.A simple method of introducing such disturbances has been numerically implemented within the framework of unsteady, transonic small-disturbance theory. Representative solutions for various airfoils subjected to chordwise and transverse gusts show that the strength and unsteady motion of the shock wave on the airfoil significantly affect the flowfield development and, consequently, the dynamic airloads. Also a study was made of the reductions in the unsteady airloads that can be achieved by the proper active control motion of a trailing-edge flap, and a simple gust-alleviation strategy was developed. However, the chordwise pressure distributions associated with gusts are very different from those produced by trailing-edge flap oscillations. Consequently, the fluctuating lift and the unsteady pitching moments cannot both be eliminated simultaneously.

L∞-Optimal feedforward gust load alleviation design for a large blended wing body airliner

NASA Astrophysics Data System (ADS)

Wildschek, A.; Haniš, T.; Stroscher, F.

2013-12-01

The potential advantages of Blended Wing Body (BWB) aircraft in terms of fuel efficiency are opposed by technical challenges such as the alleviation of gust loads. Due to the low wing, loading gusts, generally, have a more severe impact on BWB aircraft than on conventional aircraft. This paper presents the design and optimization of a Gust Load Alleviation System (GLAS) for a large BWB airliner. Numerical simulations are performed with an aeroelastic model of the aircraft including GLAS in order to compute time series of modal displacements for deriving equivalent static load cases which are used for the resizing of the aircraft structure.

Aerocrane: A hybrid LTA aircraft for aerial crane applications

NASA Technical Reports Server (NTRS)

Perkins, R. G., Jr.; Doolittle, D. B.

1975-01-01

The Aerocrane, a hybrid aircraft, combines rotor lift with buoyant lift to offer VTOL load capability greatly in excess of helicopter technology while eliminating the airship problem of ballast transfer. In addition, the Aerocrane concept sharply reduces the mooring problem of airships and provides 360 deg vectorable thrust to supply a relatively large force component for control of gust loads. Designed for use in short range, ultra heavy lift missions, the Aerocrane operates in a performance envelope unsuitable for either helicopters or airships. Basic design considerations and potential problem areas of the concept are addressed.

Alcohol impairment of performance on steering and discrete tasks in a driving simulator

DOT National Transportation Integrated Search

1974-12-01

In this program a simplified laboratory simulator was developed to test two types of tasks used in driving on the open road: a continuous "steering task" to regulate against gust induced disturbances and an intermittent "discrete response task" requi...

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 1: Load alleviation/extended span development and flight tests

NASA Technical Reports Server (NTRS)

Johnston, J. F.

1979-01-01

Active wing load alleviation to extend the wing span by 5.8 percent, giving a 3 percent reduction in cruise drag is covered. The active wing load alleviation used symmetric motions of the outboard ailerons for maneuver load control (MLC) and elastic mode suppression (EMS), and stabilizer motions for gust load alleviation (GLA). Slow maneuvers verified the MLC, and open and closed-loop flight frequency response tests verified the aircraft dynamic response to symmetric aileron and stabilizer drives as well as the active system performance. Flight tests in turbulence verified the effectiveness of the active controls in reducing gust-induced wing loads. It is concluded that active wing load alleviation/extended span is proven in the L-1011 and is ready for application to airline service; it is a very practical way to obtain the increased efficiency of a higher aspect ratio wing with minimum structural impact.

Gust-Front and Outflow Related Waterspouts: Timely Warnings, Formation, and Impact on Public Safety

NASA Astrophysics Data System (ADS)

Cappucci, M.

2013-12-01

Massachusetts may be over a thousand miles away from the traditional "tornado alley", but as the deadly tornadoes that killed four on June 1st 2011 proved, we are not immune to such storms. Over the course of half a century or so, Massachusetts has bore witness to scores of tornadoes, including an F5 twister that touched down on June 9th 1953, resulting in the death of 94 people. Since this tornado, none other in the United States had caused as many deaths, until the Joplin, Missouri catastrophe of May 22, 2011 (161 deaths). In Massachusetts, however, storms of such destructive magnitude are generally confined to the western half of the state, as the June 1, 2011 tornadoes in South Central Massachusetts illustrated. Despite this, a recently observed trend has revealed that the eastern Massachusetts coastline may boast as many, if not more, tornadoes, albeit undocumented. On June 23rd, 2012, a strong thunderstorm produced a spectacular gust front over Boston Harbor. This gust front was associated with intense thunderstorm outflow that helped to spawn a waterspout that roared ashore in Scituate as an EF-0 tornado. This waterspout, however, developed ahead of the gust front, yet merged with the cloud structure of the outflow, hinting at a type of interaction between the thunderstorm downdraft and the waterspout. This tornado caused minor damage. A similar situation occurred in Plymouth, MA, on July 24th, when three waterspouts formed ahead of the gust front of a severe thunderstorm; one of these tempests roared ashore on White Horse Beach as an EF-0 storm, causing minor damage to the sum of a few hundred dollars. Photos taken of these spouts reveal their formation ahead of the gust front, with a downdraft/waterspout interaction similar to the situation of June 23rd. Time-lapse videography of the gust front taken moments after the dissipation of the spouts reveals a horizontally oriented vortex a few hundred meters ahead of the storm's outflow boundary. The spinning of this vortex is likely caused by friction between the cooler air subducting behind the gust front against the warmer air ahead of the front. The vortex, on occasion, may be tilted onto a vertical axis by the warmer air ahead of the front; this same warm air now infiltrates the vertically-oriented vortex, thus being stretched, and forming a small waterspout. Because the waterspouts, however, are under the influence of the cool air from the thunderstorm downdraft, the spouts may move erratically before being upended. Because of the inability for NWS (National Weather Service) radar domes to detect the microscale circulation associated with such gust-front related waterspouts, forecasters at NWS offices in Massachusetts will now focus on the predecessors of waterspout formation. Among these tell-tale parameters is a well-pronounced gust-front moving over warm ocean waters, as well as a sharp, highly localized temperature contrast between the air ahead of and behind the gust front. When the NWS believes that conditions will favor the development of gust-front related waterspouts that may move onshore, a special statement will now be broadcast through the EAS system in Severe Thunderstorm Warnings. Mariners will benefit as well, with Special Marine Warnings advising caution on ';short-lived waterspouts'. Despite these alterations in NWS offices in Massachusetts, much has yet to be done to warn the public of the dangers associated with gust-front related waterspouts.

Gust alleviation - Criteria and control laws

NASA Technical Reports Server (NTRS)

Rynaski, E. G.

1979-01-01

The relationships between criteria specified for aircraft gust alleviation and the form of the control laws that result from the criteria are considered. Open-loop gust alleviation based on the linearized, small perturbation equations of aircraft motion is discussed, and an approximate solution of the open-loop control law is presented for the case in which the number of degrees of freedom of the aircraft exceeds the rank of the control effectiveness matrix. Excessive actuator lag is compensated for by taking into account actuator dynamics in the equations of motion, resulting in the specification of a general load network. Criteria for gust alleviation when output motions are gust alleviated and the closed-loop control law derived from them are examined and linear optimal control law is derived. Comparisons of the control laws reveal that the effectiveness of an open-loop control law is greatest at low aircraft frequencies but deteriorates as the natural frequency of the actuators is approached, while closed-loop methods are found to be more effective at higher frequencies.

The life cycle of thunderstorm gust fronts as viewed with Doppler radar and rawinsonde data

NASA Technical Reports Server (NTRS)

Wakimoto, R. M.

1982-01-01

This paper presents the time-dependent analysis of the thunderstorm gust front with the use of Project NIMROD data. RHI cross sections of reflectivity and Doppler velocity are constructed to determine the entire vertical structure. The life cycle of the gust front is divided into four stages: (1) the formative stage; (2) the early mature stage; (3) the late mature stage; and (4) the dissipation stage. A new finding is a horizontal roll detected in the reflectivity pattern resulting from airflow that is deflected upward by the ground, while carrying some of the smaller precipitation ahead of the main echo core of the squall line. This feature is called a 'precipitation roll'. As determined from rawinsonde data, the cold air behind the gust front accounts for the observed surface pressure rise. Calculations confirm that the collision of two fluids produce a nonhydrostatic pressure at the leading edge of the outflow. The equation governing the propagation speed of a density current accurately predicts the movement of the gust front.

Experimental Characterization and Validation of Simultaneous Gust Alleviation and Energy Harvesting for Multifunctional Wing Spars

DTIC Science & Technology

2012-08-01

U0=15m/s,  Lv  =350m   Cloud Wind and Clear Sky Gust Simulation Using Dryden PSD* Harvested Energy from Normal Vibration (Red) to...energy control law based on limited energy constraints 4) Experimentally validated simultaneous energy harvesting and vibration control Summary...Experimental Characterization and Validation of Simultaneous Gust Alleviation and Energy Harvesting for Multifunctional Wing Spars AFOSR

Forced response unsteady aerodynamics in a multistage compressor

NASA Astrophysics Data System (ADS)

Capece, Vincent Ralph

The fundamental flow physics of the unsteady aerodynamics associated with forced vibrations in turbomachinery are investigated. Unique data are obtained through a series of experiments in a three stage axial flow research compressor which quantify the unsteady harmonic gust interaction phenomena over a range of operating and geometric conditions at high values of reduced frequency. In these experiments the effects of the following on the stator vane unsteady aerodynamics were quantified: (1) the steady aerodynamic loading, (2) the detailed waveform of the aerodynamic forcing function, including the chordwise and transverse gust components, (3) multistage blade row interactions, and (4) the solidity, ranging from a design value of 1.09 to an isolated airfoil. In addition, the effect of flow separation on the unsteady aerodynamics of an isolated airfoil was also investigated.

TAILSIM Users Guide

NASA Technical Reports Server (NTRS)

Hiltner, Dale W.

2000-01-01

The TAILSIM program uses a 4th order Runge-Kutta method to integrate the standard aircraft equations-of-motion (EOM). The EOM determine three translational and three rotational accelerations about the aircraft's body axis reference system. The forces and moments that drive the EOM are determined from aerodynamic coefficients, dynamic derivatives, and control inputs. Values for these terms are determined from linear interpolation of tables that are a function of parameters such as angle-of-attack and surface deflections. Buildup equations combine these terms and dimensionalize them to generate the driving total forces and moments. Features that make TAILSIM applicable to studies of tailplane stall include modeling of the reversible control System, modeling of the pilot performing a load factor and/or airspeed command task, and modeling of vertical gusts. The reversible control system dynamics can be described as two hinged masses connected by a spring. resulting in a fifth order system. The pilot model is a standard form of lead-lag with a time delay applied to an integrated pitch rate and/or airspeed error feedback. The time delay is implemented by a Pade approximation, while the commanded pitch rate is determined by a commanded load factor. Vertical gust inputs include a single 1-cosine gust and a continuous NASA Dryden gust model. These dynamic models. coupled with the use of a nonlinear database, allow the tailplane stall characteristics, elevator response, and resulting aircraft response, to be modeled. A useful output capability of the TAILSIM program is the ability to display multiple post-run plot pages to allow a quick assessment of the time history response. There are 16 plot pages currently available to the user. Each plot page displays 9 parameters. Each parameter can also be displayed individually. on a one plot-per-page format. For a more refined display of the results the program can also create files of tabulated data. which can then be used by other plotting programs. The TAILSIM program was written straightforwardly assuming the user would want to change the database tables, the buildup equations, the output parameters. and the pilot model parameters. A separate database file and input file are automatically read in by the program. The use of an include file to set up all common blocks facilitates easy changing of parameter names and array sizes.

Evaluation of Gust and Draft Velocities from Flights of P-61c Airplanes within Thunderstorms. II - July 9, 1946 to July 11, 1946 at Orlando, Florida. II; July 9, 1946 to July 11, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, Harold B.

1946-01-01

The results obtained from an evaluation for gust and draft velocities of acceleration and airspeed-altitude records taken by NACA recording instruments installed in P-61c airplanes participating in thunderstorm flights 6, 7, and 8 of July 9, 1946, July 10, 1946, and July 11, 1946, respectively, are presented herein. These data are summarized in tables I and II. In accordance with a recent discussion with a member of the U.S. Weather Bureau staff, the tabulated results for the present flight include in addition to data of the type presented in reference 1, the initial heading of the airplane for each traverse, the pressure altitude at the start of each traverse in increments of 500 feet, and the gust gradient distance when it could be evaluated. The cloud entry and exit times for the present data were taken from motion-picture records of the pilot's instrument panels whenever such records were available while the length fo the traverses in seconds and feet was taken from the airspeed-altitude records. In many cases, however, poor agreement is indicated between the duration of the cloud traverses as obtained from the motion-picture records and from the airspeed-altitude records. This result is believed to be due to camera stoppages, inaccurate spring mechanisms of the clocks, and loss of motion-picture record in exposure or development. With reference to the evaluation of gust data, the nominal threshold was about 2 feet per second. In making gust counts to this threshold, some gusts below that threshold have been included due to limitations of the procedure used. Thus, it will be noted that in some instances gust counts are given in table I although now corresponding gust velocities are listed.

Optimality study of a gust alleviation system for light wing-loading STOL aircraft

NASA Technical Reports Server (NTRS)

Komoda, M.

1976-01-01

An analytical study was made of an optimal gust alleviation system that employs a vertical gust sensor mounted forward of an aircraft's center of gravity. Frequency domain optimization techniques were employed to synthesize the optimal filters that process the corrective signals to the flaps and elevator actuators. Special attention was given to evaluating the effectiveness of lead time, that is, the time by which relative wind sensor information should lead the actual encounter of the gust. The resulting filter is expressed as an implicit function of the prescribed control cost. A numerical example for a light wing loading STOL aircraft is included in which the optimal trade-off between performance and control cost is systematically studied.

Study of synthesis techniques for insensitive aircraft control systems

NASA Technical Reports Server (NTRS)

Harvey, C. A.; Pope, R. E.

1977-01-01

Insensitive flight control system design criteria was defined in terms of maximizing performance (handling qualities, RMS gust response, transient response, stability margins) over a defined parameter range. Wing load alleviation for the C-5A was chosen as a design problem. The C-5A model was a 79-state, two-control structure with uncertainties assumed to exist in dynamic pressure, structural damping and frequency, and the stability derivative, M sub w. Five new techniques (mismatch estimation, uncertainty weighting, finite dimensional inverse, maximum difficulty, dual Lyapunov) were developed. Six existing techniques (additive noise, minimax, multiplant, sensitivity vector augmentation, state dependent noise, residualization) and the mismatch estimation and uncertainty weighting techniques were synthesized and evaluated on the design example. Evaluation and comparison of these six techniques indicated that the minimax and the uncertainty weighting techniques were superior to the other six, and of these two, uncertainty weighting has lower computational requirements. Techniques based on the three remaining new concepts appear promising and are recommended for further research.

Dynamics of ultralight aircraft: Motion in vertical gusts

NASA Technical Reports Server (NTRS)

Jones, R. T.

1977-01-01

Gust load calculations are extended to the range of conditions encountered by ultralight aircraft such as hang gliders. Having wing loadings of the order of 5 kg/sq m, these gliders acquire a substantial fraction of the motion of a gust within a distance of 1 or 2 m. Comparative loads and displacements for a small powered airplane having a wing loading of 50 kg sq m and for a commercial jet with 500 kg sq m are shown.

A comparative framework for maneuverability and gust tolerance of aerial microsystems

NASA Astrophysics Data System (ADS)

Campbell, Renee

Aerial microsystems have the potential of navigating low-altitude, cluttered environments such as urban corridors and building interiors. Reliable systems require both agility and tolerance to gusts. While many platform designs are under development, no framework currently exists to quantitatively assess these inherent bare airframe characteristics which are independent of closed loop controllers. This research develops a method to quantify the maneuverability and gust tolerance of vehicles using reachability and disturbance sensitivity sets. The method is applied to a stable flybar helicopter and an unstable flybarless helicopter, whose state space models were formed through system identification. Model-based static H∞ controllers were also implemented on the vehicles and tested in the lab using fan-generated gusts. It is shown that the flybar restricts the bare airframe's ability to maneuver in translational velocity directions. As such, the flybarless helicopter proved more maneuverable and gust tolerant than the flybar helicopter. This approach was specifically applied here to compare stable and unstable helicopter platforms; however, the framework may be used to assess a broad range of aerial microsystems.

Jimsphere wind and turbulence exceedance statistic

NASA Technical Reports Server (NTRS)

Adelfang, S. I.; Court, A.

1972-01-01

Exceedance statistics of winds and gusts observed over Cape Kennedy with Jimsphere balloon sensors are described. Gust profiles containing positive and negative departures, from smoothed profiles, in the wavelength ranges 100-2500, 100-1900, 100-860, and 100-460 meters were computed from 1578 profiles with four 41 weight digital high pass filters. Extreme values of the square root of gust speed are normally distributed. Monthly and annual exceedance probability distributions of normalized rms gust speeds in three altitude bands (2-7, 6-11, and 9-14 km) are log-normal. The rms gust speeds are largest in the 100-2500 wavelength band between 9 and 14 km in late winter and early spring. A study of monthly and annual exceedance probabilities and the number of occurrences per kilometer of level crossings with positive slope indicates significant variability with season, altitude, and filter configuration. A decile sampling scheme is tested and an optimum approach is suggested for drawing a relatively small random sample that represents the characteristic extreme wind speeds and shears of a large parent population of Jimsphere wind profiles.

Aeroacoustic theory for noncompact wing-gust interaction

NASA Technical Reports Server (NTRS)

Martinez, R.; Widnall, S. E.

1981-01-01

Three aeroacoustic models for noncompact wing-gust interaction were developed for subsonic flow. The first is that for a two dimensional (infinite span) wing passing through an oblique gust. The unsteady pressure field was obtained by the Wiener-Hopf technique; the airfoil loading and the associated acoustic field were calculated, respectively, by allowing the field point down on the airfoil surface, or by letting it go to infinity. The second model is a simple spanwise superposition of two dimensional solutions to account for three dimensional acoustic effects of wing rotation (for a helicopter blade, or some other rotating planform) and of finiteness of wing span. A three dimensional theory for a single gust was applied to calculate the acoustic signature in closed form due to blade vortex interaction in helicopters. The third model is that of a quarter infinite plate with side edge through a gust at high subsonic speed. An approximate solution for the three dimensional loading and the associated three dimensional acoustic field in closed form was obtained. The results reflected the acoustic effect of satisfying the correct loading condition at the side edge.

Further studies using matched filter theory and stochastic simulation for gust loads prediction

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Pototzky, Anthony S.; Perry, Boyd Iii

1993-01-01

This paper describes two analysis methods -- one deterministic, the other stochastic -- for computing maximized and time-correlated gust loads for aircraft with nonlinear control systems. The first method is based on matched filter theory; the second is based on stochastic simulation. The paper summarizes the methods, discusses the selection of gust intensity for each method and presents numerical results. A strong similarity between the results from the two methods is seen to exist for both linear and nonlinear configurations.

Investigation of Optimal Control Allocation for Gust Load Alleviation in Flight Control

NASA Technical Reports Server (NTRS)

Frost, Susan A.; Taylor, Brian R.; Bodson, Marc

2012-01-01

Advances in sensors and avionics computation power suggest real-time structural load measurements could be used in flight control systems for improved safety and performance. A conventional transport flight control system determines the moments necessary to meet the pilot's command, while rejecting disturbances and maintaining stability of the aircraft. Control allocation is the problem of converting these desired moments into control effector commands. In this paper, a framework is proposed to incorporate real-time structural load feedback and structural load constraints in the control allocator. Constrained optimal control allocation can be used to achieve desired moments without exceeding specified limits on monitored load points. Minimization of structural loads by the control allocator is used to alleviate gust loads. The framework to incorporate structural loads in the flight control system and an optimal control allocation algorithm will be described and then demonstrated on a nonlinear simulation of a generic transport aircraft with flight dynamics and static structural loads.

Advanced Space Shuttle simulation model

NASA Technical Reports Server (NTRS)

Tatom, F. B.; Smith, S. R.

1982-01-01

A non-recursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed. It provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gusts gradients. Based on this model the time series for both gusts and gust gradients were generated and stored on a series of magnetic tapes, entitled Shuttle Simulation Turbulence Tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 120,000 meters. A description of the turbulence generation procedure is provided. The results of validating the simulated turbulence are described. Conclusions and recommendations are presented. One-dimensional von Karman spectra are tabulated, while a discussion of the minimum frequency simulated is provided. The results of spectral and statistical analyses of the SSTT are presented.

Factors leading to the formation of arc cloud complexes

NASA Technical Reports Server (NTRS)

Welshinger, Mark John; Brundidge, Kenneth C.

1987-01-01

A total of 12 mesoscale convective systems (MCSs) were investigated. The duration of the gust front, produced by each MCS, was used to classify the MCSs. Category 1 MCSs were defined as ones that produced a gust front and the gust front lasted for more than 6 h. There were 7 category 1 MCSs in the sample. Category 2 MCSs were defined as ones that produced a gust front and the gust front lasted for 6 h or less. There were 4 category 2 MCSs. The MCS of Case 12 was not categorized because the precipitation characteristics were similar to a squall line, rather than an MCS. All of the category 1 MCSs produced arc cloud complexes (ACCs), while only one of the category 2 MCSs produced an ACC. To determine if there were any differences in the characteristics between the MCSs of the two categories, composite analyses were accomplished. The analyses showed that there were significant differences in the characteristics of category 1 and 2 MCSs. Category 1 MCSs, on average, had higher thunderstorm heights, greater precipitation intensities, colder cloud top temperatures and produced larger magnitudes of surface divergence than category 2 MCSs.

Interaction of gusts with forest edges

NASA Astrophysics Data System (ADS)

Ruck, Bodo; Tischmacher, Michael

2012-05-01

Experimental investigations in an atmospheric boundary layer wind tunnel were carried out in order to study the interaction of gusts with forest edges. Summarizing the state of knowledge in the field of forest damages generated by extreme storms, there is a strong indication that in many cases, windthrow of trees starts near the forest edge from where it spreads into the stand. The high-transient interaction between gusts and (porous) forest edges produce unsteady flow phenomena not known so far. From a fluid mechanical point of view, the flow type resembles a forward-facing porous step flow, which is significantly influenced by the characteristics of the oncoming atmospheric boundary layer flow and the shape and `porous properties' of the forest edge. The paper reports systematic investigations on the interaction of artificially generated gusts and forest edge models in an atmospheric boundary layer wind tunnel. The experimental investigations were carried out with a laser-based time-resolved PIV-system and high speed photography. Different flow phenomena like gust streching, vortex formation, Kelvin-Helmholtz instabilities or wake production of turbulence could be measured or visualized contributing to the understanding of the complex flow perfomance over the forest edge.

Wind Tunnel Model and Test to Evaluate the Effectiveness of a Passive Gust Alleviation Device for a Flying Wing Aircraft

DTIC Science & Technology

2016-10-04

model of 1.24 m with the PGAD and control surface 3 1.2. Design and manufacture of the gust generator (frame, blades , actuation and control system...Chapter 3, a gust generator with two rotating blades was designed and manufactured to induce a transverse turbulence for wind tunnel test. A CFD...velocity at 8C (eight times of blade chord length) achieved 1.3%. In Chapter 4, the wind tunnel test of the scaled wing model is presented, including the

Analysis of data from NASA B-57B gust gradient program

NASA Technical Reports Server (NTRS)

Frost, W.; Lin, M. C.; Chang, H. P.; Ringnes, E.

1985-01-01

Statistical analysis of the turbulence measured in flight 6 of the NASA B-57B over Denver, Colorado, from July 7 to July 23, 1982 included the calculations of average turbulence parameters, integral length scales, probability density functions, single point autocorrelation coefficients, two point autocorrelation coefficients, normalized autospectra, normalized two point autospectra, and two point cross sectra for gust velocities. The single point autocorrelation coefficients were compared with the theoretical model developed by von Karman. Theoretical analyses were developed which address the effects spanwise gust distributions, using two point spatial turbulence correlations.

Comparative analysis of the Parent Attitudes about Childhood Vaccines (PACV) short scale and the five categories of vaccine acceptance identified by Gust et al.

PubMed

Oladejo, Omolade; Allen, Kristen; Amin, Avnika; Frew, Paula M; Bednarczyk, Robert A; Omer, Saad B

2016-09-22

There is a need to develop a standardized tool to aid in identifying, measuring and classifying the unique needs of vaccine-hesitant parents (VHPs). This will also assist in designing tailored interventions to address these needs. The Parental Attitude about Childhood Vaccines (PACV) short scale developed by Opel et al., and the Gust et al. vaccine acceptance categories have been acknowledged as potentially useful tools to measure parental vaccine hesitancy. The PACV short scale requires further validation. In our study, we evaluated how the Gust et al. vaccine acceptance categories correspond with the PACV short scale. As part of a larger study on vaccine attitudes, using the PACV short scale and Gust et al. vaccine acceptance categories, we assessed the correlation between the two measures using Spearman correlation coefficient, and the association between the two measures using the Cochran-Mantel-Haentszel test of association. We used logistic regression modelling to compare the association between a child's up-to-date immunization status and (a) PACV short scale and (b) Gust et al. vaccine acceptance categories. The PACV short scale and Gust et al. vaccine acceptance categories were positively correlated (r=0.6, df=198, p<0.05), and the Cochran-Mantel-Haentszel test of association yielded a statistically significant association (p<0.05). The two scales similarly predicted children's up-to-date immunization status for all recommended childhood vaccines. The ability of the PACV short scale to identify and classify parental vaccine hesitancy is similar to classification using Gust et al. vaccine acceptance categories, and both measure linear entities. The PACV short scale is recommended for screening parents at their first pediatric visit because it is easier to administer. A clearer understanding of how to classify parental vaccine hesitancy can be used to design tailored interventions based on these classifications, to address their specific needs. Copyright © 2016 Elsevier Ltd. All rights reserved.

Gusts and shear within hurricane eyewalls can exceed offshore wind turbine design standards

NASA Astrophysics Data System (ADS)

Worsnop, Rochelle P.; Lundquist, Julie K.; Bryan, George H.; Damiani, Rick; Musial, Walt

2017-06-01

Offshore wind energy development is underway in the U.S., with proposed sites located in hurricane-prone regions. Turbine design criteria outlined by the International Electrotechnical Commission do not encompass the extreme wind speeds and directional shifts of hurricanes stronger than category 2. We examine a hurricane's turbulent eyewall using large-eddy simulations with Cloud Model 1. Gusts and mean wind speeds near the eyewall of a category 5 hurricane exceed the current Class I turbine design threshold of 50 m s-1 mean wind and 70 m s-1 gusts. Largest gust factors occur at the eye-eyewall interface. Further, shifts in wind direction suggest that turbines must rotate or yaw faster than current practice. Although current design standards omit mention of wind direction change across the rotor layer, large values (15-50°) suggest that veer should be considered.

Gusts and shear within hurricane eyewalls can exceed offshore wind turbine design standards

DOE PAGES

Worsnop, Rochelle P.; Lundquist, Julie K.; Bryan, George H.; ...

2017-05-30

Here, offshore wind energy development is underway in the U.S., with proposed sites located in hurricane-prone regions. Turbine design criteria outlined by the International Electrotechnical Commission do not encompass the extreme wind speeds and directional shifts of hurricanes stronger than category 2. We examine a hurricane's turbulent eyewall using large-eddy simulations with Cloud Model 1. Gusts and mean wind speeds near the eyewall of a category 5 hurricane exceed the current Class I turbine design threshold of 50 m s –1 mean wind and 70 m s –1 gusts. Largest gust factors occur at the eye-eyewall interface. Further, shifts inmore » wind direction suggest that turbines must rotate or yaw faster than current practice. Although current design standards omit mention of wind direction change across the rotor layer, large values (15–50°) suggest that veer should be considered.« less

Gusts and shear within hurricane eyewalls can exceed offshore wind turbine design standards

DOE Office of Scientific and Technical Information (OSTI.GOV)

Worsnop, Rochelle P.; Lundquist, Julie K.; Bryan, George H.

Here, offshore wind energy development is underway in the U.S., with proposed sites located in hurricane-prone regions. Turbine design criteria outlined by the International Electrotechnical Commission do not encompass the extreme wind speeds and directional shifts of hurricanes stronger than category 2. We examine a hurricane's turbulent eyewall using large-eddy simulations with Cloud Model 1. Gusts and mean wind speeds near the eyewall of a category 5 hurricane exceed the current Class I turbine design threshold of 50 m s –1 mean wind and 70 m s –1 gusts. Largest gust factors occur at the eye-eyewall interface. Further, shifts inmore » wind direction suggest that turbines must rotate or yaw faster than current practice. Although current design standards omit mention of wind direction change across the rotor layer, large values (15–50°) suggest that veer should be considered.« less

Survey of Applications of Active Control Technology for Gust Alleviation and New Challenges for Lighter-weight Aircraft

NASA Technical Reports Server (NTRS)

Regan, Christopher D.; Jutte, Christine V.

2012-01-01

This report provides a historical survey and assessment of the state of the art in the modeling and application of active control to aircraft encountering atmospheric disturbances in flight. Particular emphasis is placed on applications of active control technologies that enable weight reduction in aircraft by mitigating the effects of atmospheric disturbances. Based on what has been learned to date, recommendations are made for addressing gust alleviation on as the trend for more structurally efficient aircraft yields both lighter and more flexible aircraft. These lighter more flexible aircraft face two significant challenges reduced separation between rigid body and flexible modes, and increased sensitivity to gust encounters due to increased wing loading and improved lift to drag ratios. The primary audience of this paper is engineering professionals new to the area of gust load alleviation and interested in tackling the multifaceted challenges that lie ahead for lighter-weight aircraft.

On vortex-airfoil interaction noise including span-end effects, with application to open-rotor aeroacoustics

NASA Astrophysics Data System (ADS)

Roger, Michel; Schram, Christophe; Moreau, Stéphane

2014-01-01

A linear analytical model is developed for the chopping of a cylindrical vortex by a flat-plate airfoil, with or without a span-end effect. The major interest is the contribution of the tip-vortex produced by an upstream rotating blade in the rotor-rotor interaction noise mechanism of counter-rotating open rotors. Therefore the interaction is primarily addressed in an annular strip of limited spanwise extent bounding the impinged blade segment, and the unwrapped strip is described in Cartesian coordinates. The study also addresses the interaction of a propeller wake with a downstream wing or empennage. Cylindrical vortices are considered, for which the velocity field is expanded in two-dimensional gusts in the reference frame of the airfoil. For each gust the response of the airfoil is derived, first ignoring the effect of the span end, assimilating the airfoil to a rigid flat plate, with or without sweep. The corresponding unsteady lift acts as a distribution of acoustic dipoles, and the radiated sound is obtained from a radiation integral over the actual extent of the airfoil. In the case of tip-vortex interaction noise in CRORs the acoustic signature is determined for vortex trajectories passing beyond, exactly at and below the tip radius of the impinged blade segment, in a reference frame attached to the segment. In a second step the same problem is readdressed accounting for the effect of span end on the aerodynamic response of a blade tip. This is achieved through a composite two-directional Schwarzschild's technique. The modifications of the distributed unsteady lift and of the radiated sound are discussed. The chained source and radiation models provide physical insight into the mechanism of vortex chopping by a blade tip in free field. They allow assessing the acoustic benefit of clipping the rear rotor in a counter-rotating open-rotor architecture.

Influence of airfoil thickness on convected gust interaction noise

NASA Technical Reports Server (NTRS)

Kerschen, E. J.; Tsai, C. T.

1989-01-01

The case of a symmetric airfoil at zero angle of attack is considered in order to determine the influence of airfoil thickness on sound generated by interaction with convected gusts. The analysis is based on a linearization of the Euler equations about the subsonic mean flow past the airfoil. Primary sound generation is found to occur in a local region surrounding the leading edge, with the size of the local region scaling on the gust wavelength. For a parabolic leading edge, moderate leading edge thickness is shown to decrease the noise level in the low Mach number limit.

A wind tunnel study of aeolian sediment transport response to unsteady winds

NASA Astrophysics Data System (ADS)

Li, Bailiang; McKenna Neuman, Cheryl

2014-06-01

Although moderate attention has been paid to the response of the aeolian mass transport rate to wind gusts, it is still unclear how the particle size and volumetric concentration affect this relation. Very little is known about the response time of the particle speed, and specifically, how the sensor scale and elevation affect measurements of this variable. The present study addresses this knowledge gap through a series of wind tunnel experiments in which a gusty wind was generated by programming the fan motor to adjust to a randomly selected rpm every 10 s. Beds consisting of either medium or coarse sand were investigated through synchronous, co-located measurements of the local wind speed and particle speed/count rate obtained via a customized laser Doppler anemometry (LDA) system. The vertically integrated sand transport rate (Q) and the wind speed in the freestream were quantified using a passive sand trap and pitot tube, respectively. The results of the experiments indicate that the response of the aeolian transport system to wind gusts is generally faster in terms of the particle speed than the mass transport rate, while the degree of correlation is found to vary with the sensor elevation, as well as with the particle size and volumetric concentration. In essence, the coupling within the transport system is demonstrated to be strongly scale dependent.

Subcritical flutter testing and system identification

NASA Technical Reports Server (NTRS)

Houbolt, J. C.

1974-01-01

Treatment is given of system response evaluation, especially in application to subcritical flight and wind tunnel flutter testing of aircraft. An evaluation is made of various existing techniques, in conjuction with a companion survey which reports theoretical and analog experiments made to study the identification of system response characteristics. Various input excitations are considered, and new techniques for analyzing response are explored, particularly in reference to the prevalent practical case where unwanted input noise is present, such as caused by gusts or wind tunnel turbulence. Further developments are also made of system parameter identification techniques.

Recent activities within the Aeroservoelasticity Branch at the NASA Langley Research Center

NASA Technical Reports Server (NTRS)

Noll, Thomas E.; Perry, Boyd, III; Gilbert, Michael G.

1989-01-01

The objective of research in aeroservoelasticity at the NASA Langley Research Center is to enhance the modeling, analysis, and multidisciplinary design methodologies for obtaining multifunction digital control systems for application to flexible flight vehicles. Recent accomplishments are discussed, and a status report on current activities within the Aeroservoelasticity Branch is presented. In the area of modeling, improvements to the Minimum-State Method of approximating unsteady aerodynamics are shown to provide precise, low-order aeroservoelastic models for design and simulation activities. Analytical methods based on Matched Filter Theory and Random Process Theory to provide efficient and direct predictions of the critical gust profile and the time-correlated gust loads for linear structural design considerations are also discussed. Two research projects leading towards improved design methodology are summarized. The first program is developing an integrated structure/control design capability based on hierarchical problem decomposition, multilevel optimization and analytical sensitivities. The second program provides procedures for obtaining low-order, robust digital control laws for aeroelastic applications. In terms of methodology validation and application the current activities associated with the Active Flexible Wing project are reviewed.

Space shuttle simulation model

NASA Technical Reports Server (NTRS)

Tatom, F. B.; Smith, S. R.

1980-01-01

The effects of atmospheric turbulence in both horizontal and near horizontal flight, during the return of the space shuttle, are important for determining design, control, and 'pilot-in-the-loop' effects. A nonrecursive model (based on von Karman spectra) for atmospheric turbulence along the flight path of the shuttle orbiter was developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gust gradients. Based on this model, the time series for both gusts and gust gradients were generated and stored on a series of magnetic tapes which are entitled shuttle simulation turbulence tapes (SSTT). The time series are designed to represent atmospheric turbulence from ground level to an altitude of 10,000 meters. The turbulence generation procedure is described as well as the results of validating the simulated turbulence. Conclusions and recommendations are presented and references cited. The tabulated one dimensional von Karman spectra and the results of spectral and statistical analyses of the SSTT are contained in the appendix.

Severe wind gust thresholds for Meteoalarm derived from uniform return periods in ECA&D

NASA Astrophysics Data System (ADS)

Stepek, A.; Wijnant, I. L.; van der Schrier, G.; van den Besselaar, E. J. M.; Klein Tank, A. M. G.

2012-06-01

In this study we present an alternative wind gust warning guideline for Meteoalarm, the severe weather warning website for Europe. There are unrealistically large differences in levels and issuing frequencies of all warning levels currently in use between neighbouring Meteoalarm countries. This study provides a guide for the Meteoalarm community to review their wind gust warning thresholds. A more uniform warning system is achieved by using one pan-European return period per warning level. The associated return values will be different throughout Europe because they depend on local climate conditions, but they will not change abruptly at country borders as is currently the case for the thresholds. As return values are a measure of the possible danger of an event and its impact on society, they form an ideal basis for a warning system. Validated wind gust measurements from the European Climate Assessment and Dataset (ECA&D, http://www.ecad.eu) were used to calculate return values of the annual maximum wind gust. The current thresholds are compared with return values for 3 different return periods: 10 times a year return periods for yellow warnings, 2 yr periods for orange and 5 yr periods for red warnings. So far 10 countries provide wind gust data to ECA&D. Due to the ECA&D completeness requirements and the fact that some countries provided too few stations to be representative for that country, medians of the return values of annual maximum wind gust could be calculated for 6 of the 10 countries. Alternative guideline thresholds are presented for Norway, Ireland, The Netherlands, Germany, the Czech Republic and Spain and the need to distinguish between coastal, inland and mountainous regions is demonstrated. The new thresholds based on uniform return periods differ significantly from the current ones, particularly for coastal and mountainous areas. We are aware of other, sometimes binding factors (e.g. laws) that prevent participating counties from implementing this climatology based warning system.

Increase in the maximum lift of an airplane wing due to a sudden increase in its effective angle of attack resulting from a gust

NASA Technical Reports Server (NTRS)

Kramer, Max

1932-01-01

Wind-tunnel tests are described, in which the angle of attack of a wing model was suddenly increased (producing the effect of a vertical gust) and the resulting forces were measured. It was found that the maximum lift coefficient increases in proportion to the rate of increase in the angle of attack. This fact is important for the determination of the gust stresses of airplanes with low wing loading. The results of the calculation of the corrective factor are given for a high-performance glider and a light sport plane of conventional type.

Investigation at Low Speeds of Deflectors and Spoilers as Gust Alleviators on a Model of the Bell X-5 Airplane with 35 Degree Swept Wings and on a High-aspect-ratio 35 Degree Swept-wing-fuselage Model

NASA Technical Reports Server (NTRS)

Croom, Delwin R; Huffman, Jarrett K

1957-01-01

Results of an investigation at low speeds to determine the gust-alleviation capabilities (reduction in lift-curve slope) of spoilers and deflectors on a 35 degree swept-wing model of high aspect ratio and on a 1/4-scale model of the X-5 airplane with 35 degree swept wings indicate that deflector and spoiler-deflector types of controls can be designed to provide considerable gust alleviation for a swept-wing airplane while still maintaining stability and control.

Stable H(infinity) Controller Design for the Longitudinal Dynamics of an Aircraft

NASA Technical Reports Server (NTRS)

Oezbay, Hitay; Garg, Sanjay

1995-01-01

This report discusses different approaches to stable H infinity controller design applied to the problem of augmenting the longitudinal dynamics of an aircraft. Stability of the H infinity controller is investigated by analyzing the effects of changes in the performance index weights, and modifications in the measured outputs. The existence of a stable suboptimal controller is also investigated. It is shown that this is equivalent to finding a stable controller, whose infinity norm is less than a specified bound, for an unstable plant which is determined from parametrization of all H infinity controllers. Examples are given for a gust alleviation and a command tracking problem.

14 CFR 25.679 - Control system gust locks.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Automatically disengage when the pilot operates the primary flight controls in a normal manner; or (2) Limit the... 14 Aeronautics and Space 1 2013-01-01 2013-01-01 false Control system gust locks. 25.679 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction Control Systems § 25.679 Control...

75 FR 47905 - Cranes and Derricks in Construction

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-09

... guiding a large roof section, being lifted by another crane, into place. Winds gusting to 27 miles per... wind and other adverse weather conditions on the equipment's stability and rated capacity. In addition, Sec. 1926.1431, Hoisting personnel, requires that, when wind speed (sustained or gust) exceeds 20 mph...

Effect of wind gusts on the motion of a balloon-borne observation platform

NASA Technical Reports Server (NTRS)

Nigro, N. J.; Johanek, F. M.

1982-01-01

The effect of wind gusts on the magnitude of the pendulation angles of a balloon-borne observation platform is determined. A system mathematical model is developed and the solution of this model is used to determine the magnitude of the observation platforms pendulation angles.

Roll tracking effects of G-vector tilt and various types of motion washout

NASA Technical Reports Server (NTRS)

Jex, H. R.; Magdaleno, R. E.; Junker, A. M.

1978-01-01

In a dogfight scenario, the task was to follow the target's roll angle while suppressing gust disturbances. All subjects adopted the same behavioral strategies in following the target while suppressing the gusts, and the MFP-fitted math model response was generally within one data symbol width. The results include the following: (1) comparisons of full roll motion (both with and without the spurious gravity tilt cue) with the static case. These motion cues help suppress disturbances with little net effect on the visual performance. Tilt cues were clearly used by the pilots but gave only small improvement in tracking errors. (2) The optimum washout (in terms of performance close to real world, similar behavioral parameters, significant motion attenuation (60 percent), and acceptable motion fidelity) was the combined attenuation and first-order washout. (3) Various trends in parameters across the motion conditions were apparent, and are discussed with respect to a comprehensive model for predicting adaptation to various roll motion cues.

Control concepts for the alleviation of windshears and gusts

NASA Technical Reports Server (NTRS)

Rynaski, E. G.; Govindaraj, K. S.

1982-01-01

Automatic control system design methods for gust and shear alleviation were studied. It is shown that automatic gust/shear alleviation systems can be quite effective if both throttle and elevator are used in harmony to produce the forces and moments required to counter the effects of the windshear. Regulation with respect to ground speed or airspeed results in very similar system designs. The application of the NASA total energy probe in the detection of windshear and criteria for alleviation is considered. The theory and application of robust output observers is extended. Design examples show how implementation of the control laws can be accomplished using observers, and thereby resulting in less complex control system configurations.

B-737 Linear Autoland Simulink Model

NASA Technical Reports Server (NTRS)

Belcastro, Celeste (Technical Monitor); Hogge, Edward F.

2004-01-01

The Linear Autoland Simulink model was created to be a modular test environment for testing of control system components in commercial aircraft. The input variables, physical laws, and referenced frames used are summarized. The state space theory underlying the model is surveyed and the location of the control actuators described. The equations used to realize the Dryden gust model to simulate winds and gusts are derived. A description of the pseudo-random number generation method used in the wind gust model is included. The longitudinal autopilot, lateral autopilot, automatic throttle autopilot, engine model and automatic trim devices are considered as subsystems. The experience in converting the Airlabs FORTRAN aircraft control system simulation to a graphical simulation tool (Matlab/Simulink) is described.

Estimation of Gust Response Factor for a Tall Building Model with 1:1.5 Plan Ratios

NASA Astrophysics Data System (ADS)

Sarath Kumar, H.; Selvi Rajan, S.

2017-08-01

The purpose of structural analysis and design of structures as per the building codes and its corresponding standers is to ensure the safety of structure under maximum loads and remains functional under service load. The structure which is designed under consideration of codes should also satisfy the durability, economy and aesthetics. The primary purpose of this work is to understand and compare design wind loads according with the Gust Response Factor as per codes of practices. The paper is concerned with the calculation of design wind loads on a rectangular building model (1:300gemetric scale) of size 10cm x 15cm x 70cm with an aspect ratio of 1:1.5:7 at eight different levels over the height under sub-urban terrain category for 00 angle and 900 angle wind incidence. The experiment id conducted in an atmospheric boundary layer wind tunnel facility of CSIR-Structural engineering Research centre, Chennai. The measured pressures are integrated to evaluate mean and RMS (Root, Mean, Square). Further the variation of above mentioned loads and response factor along the heights of the building with respect to sub-urban terrain condition are discussed and summarized in addition, the codal values of various international standards [IS-875 part-3 1987, IS-875 part-3 draft, ASCE-07] have also considered for comparison.

78 FR 31851 - Harmonization of Airworthiness Standards-Gust and Maneuver Load Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-28

... airplanes equipped with wing-mounted engines; revise the engine torque loads criteria; add an engine failure... equipped with wing-mounted engines. Following an accident in which an airplane shed a large wing- mounted...-93-137, November 15, 1993). This recommendation was specifically aimed at gust loads on wing-mounted...

14 CFR 25.345 - High lift devices.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false High lift devices. 25.345 Section 25.345... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.345 High lift...) A head-on gust of 25 feet per second velocity (EAS). (c) If flaps or other high lift devices are to...

14 CFR 25.345 - High lift devices.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false High lift devices. 25.345 Section 25.345... STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.345 High lift...) A head-on gust of 25 feet per second velocity (EAS). (c) If flaps or other high lift devices are to...

Effect of spanwise variations in gust intensity on the lift due to atmospheric turbulence

NASA Technical Reports Server (NTRS)

Diederich, Franklin W; Drischler, Joseph A

1957-01-01

The effect of spanwise variations in gust intensity on the power spectrum directly due to atmospheric turbulence is calculated for several analytic approximations to the correlation function or power spectra of atmospheric turbulence, for several spanwise weighing functions (span loadings), and for various angles of sweepback.

14 CFR 23.443 - Gust loads.

Code of Federal Regulations, 2010 CFR

2010-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443 Gust loads. (a) Vertical surfaces must be designed to withstand, in unaccelerated flight at speed V C... computed as follows: ER09FE96.000 Where— Lvt=Vertical surface loads (lbs.); ER09FE96.001 ER09FE96.002 Ude...

14 CFR 23.443 - Gust loads.

Code of Federal Regulations, 2012 CFR

2012-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443 Gust loads. (a) Vertical surfaces must be designed to withstand, in unaccelerated flight at speed V C... computed as follows: ER09FE96.000 Where— Lvt=Vertical surface loads (lbs.); ER09FE96.001 ER09FE96.002 Ude...

14 CFR 23.443 - Gust loads.

Code of Federal Regulations, 2014 CFR

2014-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443 Gust loads. (a) Vertical surfaces must be designed to withstand, in unaccelerated flight at speed V C... computed as follows: ER09FE96.000 Where— Lvt=Vertical surface loads (lbs.); ER09FE96.001 ER09FE96.002 Ude...

14 CFR 23.443 - Gust loads.

Code of Federal Regulations, 2013 CFR

2013-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443 Gust loads. (a) Vertical surfaces must be designed to withstand, in unaccelerated flight at speed V C... computed as follows: ER09FE96.000 Where— Lvt=Vertical surface loads (lbs.); ER09FE96.001 ER09FE96.002 Ude...

14 CFR 23.443 - Gust loads.

Code of Federal Regulations, 2011 CFR

2011-01-01

... STANDARDS: NORMAL, UTILITY, ACROBATIC, AND COMMUTER CATEGORY AIRPLANES Structure Vertical Surfaces § 23.443 Gust loads. (a) Vertical surfaces must be designed to withstand, in unaccelerated flight at speed V C... computed as follows: ER09FE96.000 Where— Lvt=Vertical surface loads (lbs.); ER09FE96.001 ER09FE96.002 Ude...

Atmospheric turbulence simulation for Shuttle orbiter

NASA Technical Reports Server (NTRS)

Tatom, F. B.; Smith, S. R.

1979-01-01

An improved non-recursive model for atmospheric turbulence along the flight path of the Shuttle Orbiter is developed which provides for simulation of instantaneous vertical and horizontal gusts at the vehicle center-of-gravity, and also for simulation of instantaneous gust gradients. Based on this model the time series for both gusts and gust gradients are generated and stored on a series of magnetic tapes. Section 2 provides a description of the various technical considerations associated with the turbulence simulation model. Included in this section are descriptions of the digital filter simulation model, the von Karman spectra with finite upper limits, and the final non recursive turbulence simulation model which was used to generate the time series. Section 2 provides a description of the various technical considerations associated with the turbulence simulation model. Included in this section are descriptions of the digial filter simulation model, the von Karman spectra with finite upper limits, and the final non recursive turbulence simulation model which was used to generate the time series. Section 3 provides a description of the time series as currently recorded on magnetic tape. Conclusions and recommendations are presented in Section 4.

Atmospheric Disturbance Environment Definition

NASA Technical Reports Server (NTRS)

Tank, William G.

1994-01-01

Traditionally, the application of atmospheric disturbance data to airplane design problems has been the domain of the structures engineer. The primary concern in this case is the design of structural components sufficient to handle transient loads induced by the most severe atmospheric "gusts" that might be encountered. The concern has resulted in a considerable body of high altitude gust acceleration data obtained with VGH recorders (airplane velocity, V, vertical acceleration, G, altitude, H) on high-flying airplanes like the U-2 (Ehernberger and Love, 1975). However, the propulsion system designer is less concerned with the accelerations of the airplane than he is with the airflow entering the system's inlet. When the airplane encounters atmospheric turbulence it responds with transient fluctuations in pitch, yaw, and roll angles. These transients, together with fluctuations in the free-stream temperature and pressure will disrupt the total pressure, temperature, Mach number and angularity of the inlet flow. For the mixed compression inlet, the result is a disturbed throat Mach number and/or shock position, and in extreme cases an inlet unstart can occur (cf. Section 2.1). Interest in the effects of inlet unstart on the vehicle dynamics of large, supersonic airplanes is not new. Results published by NASA in 1962 of wind tunnel studies of the problem were used in support of the United States Supersonic Transport program (SST) (White, at aI, 1963). Such studies continued into the late 1970's. However, in spite of such interest, there never was developed an atmospheric disturbance database for inlet unstart analysis to compare with that available for the structures load analysis. Missing were data for the free-stream temperature and pressure disturbances that also contribute to the unStart problem.

A simplified application of the method of operators to the calculation of disturbed motions of an airplane

NASA Technical Reports Server (NTRS)

Jones, Robert T

1937-01-01

A simplified treatment of the application of Heaviside's operational methods to problems of airplane dynamics is given. Certain graphical methods and logarithmic formulas that lessen the amount of computation involved are explained. The problem representing a gust disturbance or control manipulation is taken up and it is pointed out that in certain cases arbitrary control manipulations may be dealt with as though they imposed specific constraints on the airplane, thus avoiding the necessity of any integration. The application of the calculations described in the text is illustrated by several examples chosen to show the use of the methods and the practicability of the graphical and logarithmic computations described.

Downdraft outflows: climatological potential to influence fire behaviour

Treesearch

Brian E. Potter; Jaime R. Hernandez

2017-01-01

Sudden wind shifts caused by atmospheric gust fronts can lead to firefighter entrapments and fatalities. In this study, we describe the physical processes involved in the related phenomena of convective downdrafts, gust fronts and downbursts. We focus on the dominant process, evaporative cooling in a dry surface layer, as characterised by the measure known as downdraft...

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms September 10, 1947 to September 15, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from September 10, 1947 to September 15, 1947, are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms August 13, 1947 to August 15, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 13, 1947 to August 15, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms August 16, 1947 to August 20, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from August 16, 1947 to August 20, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms September 4, 1947 to September 5, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from September 4, 1947 to September 5, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms June 11, 1947 to July 11, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from June 11, 1947 to July 11, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms June 2, 1947 to June 7, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from June 2, 1947 to June 7, 1947, are presented.

Evaluation of Gust and Draft Velocities from Flights of F-61C Airplanes within Thunderstorms August 7, 1947 to August 13, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1948-01-01

The gust and draft velocities from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air FIeld, Ohio, from August 7, 1947 to August 13, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms July 12, 1947 to July 18, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Funk, Jack

1947-01-01

The gust and draft velocities from records of NACA instruments installed in P-61c airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from July 12, to July 18, 1947 are presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms September 11, 1946 to September 16, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period from September 11, 1946 to September 16, 1946 at Orlando, Florida are presented herein. These data are summarized in.and presented.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms May 13, 1947 to May 29, 1947 at Clinton County Army Air Field, Ohio

NASA Technical Reports Server (NTRS)

Tolefson, Harold B.

1948-01-01

The gust and draft velocities evaluated from records of NACA instruments installed in P-61C airplanes participating in thunderstorm flights at Clinton County Army Air Field, Ohio, from May 13 to May 29, 1947 are presented.

A computer program to obtain time-correlated gust loads for nonlinear aircraft using the matched-filter-based method

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Pototzky, Anthony S.; Perry, Boyd, III

1994-01-01

NASA Langley Research Center has, for several years, conducted research in the area of time-correlated gust loads for linear and nonlinear aircraft. The results of this work led NASA to recommend that the Matched-Filter-Based One-Dimensional Search Method be used for gust load analyses of nonlinear aircraft. This manual describes this method, describes a FORTRAN code which performs this method, and presents example calculations for a sample nonlinear aircraft model. The name of the code is MFD1DS (Matched-Filter-Based One-Dimensional Search). The program source code, the example aircraft equations of motion, a sample input file, and a sample program output are all listed in the appendices.

Some properties of a 5-parameter bivariate probability distribution

NASA Technical Reports Server (NTRS)

Tubbs, J. D.; Brewer, D. W.; Smith, O. E.

1983-01-01

A five-parameter bivariate gamma distribution having two shape parameters, two location parameters and a correlation parameter was developed. This more general bivariate gamma distribution reduces to the known four-parameter distribution. The five-parameter distribution gives a better fit to the gust data. The statistical properties of this general bivariate gamma distribution and a hypothesis test were investigated. Although these developments have come too late in the Shuttle program to be used directly as design criteria for ascent wind gust loads, the new wind gust model has helped to explain the wind profile conditions which cause large dynamic loads. Other potential applications of the newly developed five-parameter bivariate gamma distribution are in the areas of reliability theory, signal noise, and vibration mechanics.

Turbulent transport model of wind shear in thunderstorm gust fronts and warm fronts

NASA Technical Reports Server (NTRS)

Lewellen, W. S.; Teske, M. E.; Segur, H. C. O.

1978-01-01

A model of turbulent flow in the atmospheric boundary layer was used to simulate the low-level wind and turbulence profiles associated with both local thunderstorm gust fronts and synoptic-scale warm fronts. Dimensional analyses of both type fronts provided the physical scaling necessary to permit normalized simulations to represent fronts for any temperature jump. The sensitivity of the thunderstorm gust front to five different dimensionless parameters as well as a change from axisymmetric to planar geometry was examined. The sensitivity of the warm front to variations in the Rossby number was examined. Results of the simulations are discussed in terms of the conditions which lead to wind shears which are likely to be most hazardous for aircraft operations.

In-flight gust monitoring and aeroelasticity studies

NASA Astrophysics Data System (ADS)

Alvarez-Salazar, Oscar Salvador

An in-flight gust monitoring and aeroelasticity study was conducted on board NASA Dryden's F15-B/FTF-II test platform (``FTF''). A total of four flights were completed. This study is the first in a series of flight experiments being conducted jointly by NASA Dryden Flight Research Center and UCLA's Flight Systems Research Center. The first objective of the in-flight gust- monitoring portion of the study was to demonstrate for the first time anywhere the measurability of intensity variations of a collimated Helium-Neon laser beam due to atmospheric air turbulence while having both the source and target apertures mounted outside an airborne aircraft. Intensity beam variations are the result of forward scattering of the beam by variations in the air's index of refraction, which are carried across the laser beam's path by a cross flow or air (i.e., atmospheric turbulence shifting vertically in the atmosphere). A laser beam was propagated parallel to the direction of flight for 1/2 meter outside the flight test fixture and its intensity variations due to atmospheric turbulence were successfully measured by a photo- detector. When the aircraft did not fly through a field of atmospheric turbulence, the laser beam proved to be insensitive to the stream velocity's cross component to the path of the beam. The aeroelasticity portion of the study consisted of measurements of the dynamic response of a straight, 18.25 inch span, 4.00 inch chord, NACA 0006 airfoil thickness profile, one sided wing to in-flight aircraft maneuvers, landing gear buffeting, unsteady aerodynamics, atmospheric turbulence, and aircraft vibration in general. These measurements were accomplished through the use of accelerometers, strain gauges and in-flight video cameras. Data collected will be used to compute in-flight root loci for the wing as functions of the aircraft's stream velocity. The data may also be used to calibrate data collected by the gust-monitoring system flown, and help verify the accuracy of various aeroelastic modeling techniques for estimating the stability boundary of a flexible wing in flight (i.e., flutter).

Further studies with data collected by NASA's airborne Doppler lidar in Oklahoma in 1981

NASA Technical Reports Server (NTRS)

Bluestein, H. B.; Mccaul, E. W., Jr.

1986-01-01

Continued study of the lidar data collected in 1981 has resulted in significant new improvements in the analysis techniques reported by Bluestein et al. (1985) and McCaul (1985). Through comparison of fore- and aft-derived scalar fields of intensity and spectral width, the self-consistency of the lidar moment estimates was assessed. Reflectivity estimates were found to be quite stable and reliable, while spectral widths were prone to become noisy if signal to noise ratio (SNR) fell below 12 dB. In addition, spectral widths contained a significant component due to radial velocity gradients in areas along gust fronts, and these components were different along the fore and aft lines of sight. Significant improvement in agreement between the fore and aft fields of spectral width was obtained by estimating the radial velocity gradient component and then removing it from the raw measured widths to yield only the turbulent portion of the contribution to width. Additional analyses showed that lidar-derived vorticity estimates were consistent with several approximate models of vorticity growth along gust front zones, and with the hypothesis that Helmholtz instability could have been responsible for vortices seen along part of the gust front of 30 June 1981. Computations of divergence transverse to axes through an isolated cumulus congestus indicated that the strongest convergence tended to lie along an axis parallel to the congestus. This and the results of other additional analyses seem to suggest that the lidar winds do indeed accurately reflected the basic features of the real wind field.

Selection of sampling rate for digital control of aircrafts

NASA Technical Reports Server (NTRS)

Katz, P.; Powell, J. D.

1974-01-01

The considerations in selecting the sample rates for digital control of aircrafts are identified and evaluated using the optimal discrete method. A high performance aircraft model which includes a bending mode and wind gusts was studied. The following factors which influence the selection of the sampling rates were identified: (1) the time and roughness response to control inputs; (2) the response to external disturbances; and (3) the sensitivity to variations of parameters. It was found that the time response to a control input and the response to external disturbances limit the selection of the sampling rate. The optimal discrete regulator, the steady state Kalman filter, and the mean response to external disturbances are calculated.

Evaluation of total energy-rate feedback for glidescope tracking in wind shear

NASA Technical Reports Server (NTRS)

Belcastro, C. M.; Ostroff, A. J.

1986-01-01

Low-altitude wind shear is recognized as an infrequent but significant hazard to all aircraft during take-off and landing. A total energy-rate sensor, which is potentially applicable to this problem, has been developed for measuring specific total energy-rate of an airplane with respect to the air mass. This paper presents control system designs, with and without energy-rate feedback, for the approach to landing of a transport airplane through severe wind shear and gusts to evaluate application of this sensor. A system model is developed which incorporates wind shear dynamics equations with the airplance equations of motion, thus allowing the control systems to be analyzed under various wind shears. The control systems are designed using optimal output feedback and are analyzed using frequency domain control theory techniques. Control system performance is evaluated using a complete nonlinear simulation of the airplane and a severe wind shear and gust data package. The analysis and simulation results indicate very similar stability and performance characteristics for the two designs. An implementation technique for distributing the velocity gains between airspeed and ground speed in the simulation is also presented, and this technique is shown to improve the performance characteristics of both designs.

Identification of Linear and Nonlinear Aerodynamic Impulse Responses Using Digital Filter Techniques

NASA Technical Reports Server (NTRS)

Silva, Walter A.

1997-01-01

This paper discusses the mathematical existence and the numerically-correct identification of linear and nonlinear aerodynamic impulse response functions. Differences between continuous-time and discrete-time system theories, which permit the identification and efficient use of these functions, will be detailed. Important input/output definitions and the concept of linear and nonlinear systems with memory will also be discussed. It will be shown that indicial (step or steady) responses (such as Wagner's function), forced harmonic responses (such as Theodorsen's function or those from doublet lattice theory), and responses to random inputs (such as gusts) can all be obtained from an aerodynamic impulse response function. This paper establishes the aerodynamic impulse response function as the most fundamental, and, therefore, the most computationally efficient, aerodynamic function that can be extracted from any given discrete-time, aerodynamic system. The results presented in this paper help to unify the understanding of classical two-dimensional continuous-time theories with modern three-dimensional, discrete-time theories. First, the method is applied to the nonlinear viscous Burger's equation as an example. Next the method is applied to a three-dimensional aeroelastic model using the CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code and then to a two-dimensional model using the CFL3D Navier-Stokes code. Comparisons of accuracy and computational cost savings are presented. Because of its mathematical generality, an important attribute of this methodology is that it is applicable to a wide range of nonlinear, discrete-time problems.

Identification of Linear and Nonlinear Aerodynamic Impulse Responses Using Digital Filter Techniques

NASA Technical Reports Server (NTRS)

Silva, Walter A.

1997-01-01

This paper discusses the mathematical existence and the numerically-correct identification of linear and nonlinear aerodynamic impulse response functions. Differences between continuous-time and discrete-time system theories, which permit the identification and efficient use of these functions, will be detailed. Important input/output definitions and the concept of linear and nonlinear systems with memory will also be discussed. It will be shown that indicial (step or steady) responses (such as Wagner's function), forced harmonic responses (such as Tbeodorsen's function or those from doublet lattice theory), and responses to random inputs (such as gusts) can all be obtained from an aerodynamic impulse response function. This paper establishes the aerodynamic impulse response function as the most fundamental, and, therefore, the most computationally efficient, aerodynamic function that can be extracted from any given discrete-time, aerodynamic system. The results presented in this paper help to unify the understanding of classical two-dimensional continuous-time theories with modem three-dimensional, discrete-time theories. First, the method is applied to the nonlinear viscous Burger's equation as an example. Next the method is applied to a three-dimensional aeroelastic model using the CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) code and then to a two-dimensional model using the CFL3D Navier-Stokes code. Comparisons of accuracy and computational cost savings are presented. Because of its mathematical generality, an important attribute of this methodology is that it is applicable to a wide range of nonlinear, discrete-time problems.

On Wind Forces in the Forest-Edge Region During Extreme-Gust Passages and Their Implications for Damage Patterns

NASA Astrophysics Data System (ADS)

Gromke, Christof; Ruck, Bodo

2018-03-01

A damage pattern that is occasionally found after a period of strong winds shows an area of damaged trees inside a forest stand behind an intact stripe of trees directly at the windward edge. In an effort to understand the mechanism leading to this damage pattern, wind loading in the forest-edge region during passages of extreme gusts with different characteristics are investigated using a scaled forest model in the wind tunnel. The interaction of a transient extreme gust with the stationary atmospheric boundary layer (ABL) as a background flow at the forest edge leads to the formation of a vortex at the top of the canopy. This vortex intensifies when travelling downstream and subsequently deflects high-momentum air from above the canopy downwards resulting in increased wind loading on the tree crowns. Under such conditions, the decrease in wind loading in the streamwise direction can be relatively weak compared to stationary ABL approach flows. The resistance of trees with streamwise distance from the forest edge, however, is the result of adaptive growth to wind loading under stationary flow conditions and shows a rapid decline within two to three tree heights behind the windward edge. For some of the extreme gusts realized, an exceedance of the wind loading over the resistance of the trees is found at approximately three tree heights behind the forest edge, suggesting that the damage pattern described above can be caused by the interaction of a transient extreme gust with the stationary ABL flow.

Aerodynamic robustness in owl-inspired leading-edge serrations: a computational wind-gust model.

PubMed

Rao, Chen; Liu, Hao

2018-06-08

Owls are a master to achieve silent flight in gliding and flapping flights under natural turbulent environments owing to their unique wing morphologies. While the leading-edge serrations are recently revealed, as a passive flow control micro-device, to play a crucial role in aerodynamic force production and sound suppression [25], the characteristics of wind-gust rejection associated with leading-edge serrations remain unclear. Here we address a large-eddy simulation (LES)-based study of aerodynamic robustness in owl-inspired leading-edge serrations, which is conducted with clean and serrated wing models through mimicking wind-gusts under a longitudinal fluctuation in free-stream inflow and a lateral fluctuation in pitch angle over a broad range of angles of attack (AoAs) over 0° ≤ Φ ≤ 20°. Our results show that the leading-edge serration-based passive flow control mechanisms associated with laminar-turbulent transition work effectively under fluctuated inflow and wing pitch, indicating that the leading-edge serrations are of potential gust fluctuation rejection or robustness in aerodynamic performance. Moreover, it is revealed that the tradeoff between turbulent flow control (i.e., aero-acoustic suppression) and force production in the serrated model holds independently to the wind-gust environments: poor at lower AoAs but capable of achieving equivalent aerodynamic performance at higher AoAs > 15o compared to the clean model. Our results reveal that the owl-inspired leading-edge serrations can be a robust micro-device for aero-acoustic control coping with unsteady and complex wind environments in biomimetic rotor designs for various fluid machineries. © 2018 IOP Publishing Ltd.

Stratospheric turbulence measurements and models for aerospace plane design

NASA Technical Reports Server (NTRS)

Ehernberger, L. J.

1992-01-01

Progress in computational atmospheric dynamics is exhibiting the ability of numerical simulation to describe instability processes associated with turbulence observed at altitudes between 15 and 25 km in the lower stratosphere. As these numerical simulation tools mature, they can be used to extend estimates of atmospheric perturbations from the present gust database for airplane design at altitudes below 15 km to altitudes between 25 and 50 km where aerospace plane operation would be at hypersonic speeds. The amount of available gust data and number of temperature perturbation observations are limited at altitudes between 15 and 25 km. On the other hand, in-situ gust data at higher altitudes are virtually nonexistent. The uncertain potential for future airbreathing hypersonic flight research vehicles to encounter strong turbulence at higher altitudes could penalize the design of these vehicles by undue cost or limitations on performance. Because the atmospheric structure changes markedly with altitude, direct extrapolation of gust magnitudes and encounter probabilities to the higher flight altitudes is not advisable. This paper presents a brief review of turbulence characteristics observed in the lower stratosphere and highlights the progress of computational atmospheric dynamics that may be used to estimate the severity of atmospheric transients at higher altitudes.

Analysis of low altitude atmospheric turbulence data measured in flight

NASA Technical Reports Server (NTRS)

Ganzer, V. M.; Joppa, R. G.; Vanderwees, G.

1977-01-01

All three components of turbulence were measured simultaneously in flight at each wing tip of a Beech D-18 aircraft. The flights were conducted at low altitude, 30.5 - 61.0 meters (100-200 ft.), over water in the presence of wind driven turbulence. Statistical properties of flight measured turbulence were compared with Gaussian and non-Gaussian turbulence models. Spatial characteristics of the turbulence were analyzed using the data from flight perpendicular and parallel to the wind. The probability density distributions of the vertical gusts show distinctly non-Gaussian characteristics. The distributions of the longitudinal and lateral gusts are generally Gaussian. The power spectra compare in the inertial subrange at some points better with the Dryden spectrum, while at other points the von Karman spectrum is a better approximation. In the low frequency range the data show peaks or dips in the power spectral density. The cross between vertical gusts in the direction of the mean wind were compared with a matched non-Gaussian model. The real component of the cross spectrum is in general close to the non-Gaussian model. The imaginary component, however, indicated a larger phase shift between these two gust components than was found in previous research.

Qualitative comparison of calculated turbulence responses with wind-tunnel measurements for a DC-10 derivative wing with an active control system

NASA Technical Reports Server (NTRS)

Perry, B., III

1981-01-01

Comparisons are presented analytically predicted and experimental turbulence responses of a wind tunnel model of a DC-10 derivative wing equipped with an active control system. The active control system was designed for the purpose of flutter suppression, but it had additional benefit of alleviating gust loads (wing bending moment) by about 25%. Comparisions of various wing responses are presented for variations in active control system parameters and tunnel speed. The analytical turbulence responses were obtained using DYLOFLEX, a computer program for dynamic loads analyses of flexible airplanes with active controls. In general, the analytical predictions agreed reasonably well with the experimental data.

Aerodynamics of Cascaded Airfoils Oscillating or Subject to Three-Dimensional Periodic Gusts.

DTIC Science & Technology

1980-01-01

and guide vanes and induce fluctuating aerodynamic forces on their blades . The aeroelastic stability of the engine , therefore, depends on the...71, we carried out a comparative study for a compressor, a I turbine , a flat plate cascade, and a single airfoil having the same blade geometry. Table...amplification of acoustic response, and inducing blade vibrations. In particular, during take-off and landing of jet powered aircraft the presence

Evaluation of Gust and Draft Velocities from Flights of P-61c Airplanes within Thunderstorms August 7, 1946 to August 13, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, Harold B.

1946-01-01

This report presents the results obtained from gust and draft velocity measurements within thunderstorms for the period August 7, 1946 to August, 13, 1946 at Orlando Florida. In several of the surveys, indications of ambient air temperature were obtained from photo-observer records. These data are summarized in the report.

NASA's aviation safety research and technology program

NASA Technical Reports Server (NTRS)

Fichtl, G. H.

1977-01-01

Aviation safety is challenged by the practical necessity of compromising inherent factors of design, environment, and operation. If accidents are to be avoided these factors must be controlled to a degree not often required by other transport modes. The operational problems which challenge safety seem to occur most often in the interfaces within and between the design, the environment, and operations where mismatches occur due to ignorance or lack of sufficient understanding of these interactions. Under this report the following topics are summarized: (1) The nature of operating problems, (2) NASA aviation safety research, (3) clear air turbulence characterization and prediction, (4) CAT detection, (5) Measurement of Atmospheric Turbulence (MAT) Program, (6) Lightning, (7) Thunderstorm gust fronts, (8) Aircraft ground operating problems, (9) Aircraft fire technology, (10) Crashworthiness research, (11) Aircraft wake vortex hazard research, and (12) Aviation safety reporting system.

Airborne Coherent Lidar for Advanced In-Flight Measurements (ACLAIM) Flight Testing of the Lidar Sensor

NASA Technical Reports Server (NTRS)

Soreide, David C.; Bogue, Rodney K.; Ehernberger, L. J.; Hannon, Stephen M.; Bowdle, David A.

2000-01-01

The purpose of the ACLAIM program is ultimately to establish the viability of light detection and ranging (lidar) as a forward-looking sensor for turbulence. The goals of this flight test are to: 1) demonstrate that the ACLAIM lidar system operates reliably in a flight test environment, 2) measure the performance of the lidar as a function of the aerosol backscatter coefficient (beta), 3) use the lidar system to measure atmospheric turbulence and compare these measurements to onboard gust measurements, and 4) make measurements of the aerosol backscatter coefficient, its probability distribution and spatial distribution. The scope of this paper is to briefly describe the ACLAIM system and present examples of ACLAIM operation in flight, including comparisons with independent measurements of wind gusts, gust-induced normal acceleration, and the derived eddy dissipation rate.

Inventory of File gfs.t06z.pgrb2.1p00.f000

Science.gov Websites

analysis U-Component of Wind [m/s] 002 planetary boundary layer VGRD analysis V-Component of Wind [m/s] 003 planetary boundary layer VRATE analysis Ventilation Rate [m^2/s] 004 surface GUST analysis Wind Speed (Gust mb RH analysis Relative Humidity [%] 008 10 mb UGRD analysis U-Component of Wind [m/s] 009 10 mb VGRD

Inventory of File gfs.t06z.pgrb2.0p50.f000

Science.gov Websites

analysis U-Component of Wind [m/s] 002 planetary boundary layer VGRD analysis V-Component of Wind [m/s] 003 planetary boundary layer VRATE analysis Ventilation Rate [m^2/s] 004 surface GUST analysis Wind Speed (Gust mb RH analysis Relative Humidity [%] 008 10 mb UGRD analysis U-Component of Wind [m/s] 009 10 mb VGRD

Inventory of File gfs.t06z.pgrb2.0p25.f000

Science.gov Websites

analysis U-Component of Wind [m/s] 002 planetary boundary layer VGRD analysis V-Component of Wind [m/s] 003 planetary boundary layer VRATE analysis Ventilation Rate [m^2/s] 004 surface GUST analysis Wind Speed (Gust mb RH analysis Relative Humidity [%] 008 10 mb UGRD analysis U-Component of Wind [m/s] 009 10 mb VGRD

Inventory of File gfs.t06z.pgrb2.2p50.f000

Science.gov Websites

analysis U-Component of Wind [m/s] 002 planetary boundary layer VGRD analysis V-Component of Wind [m/s] 003 planetary boundary layer VRATE analysis Ventilation Rate [m^2/s] 004 surface GUST analysis Wind Speed (Gust mb RH analysis Relative Humidity [%] 008 10 mb UGRD analysis U-Component of Wind [m/s] 009 10 mb VGRD

High altitude gust acceleration environment as experienced by a supersonic airplane

NASA Technical Reports Server (NTRS)

Ehernberger, L. J.; Love, B. J.

1975-01-01

High altitude turbulence experienced at supersonic speeds is described in terms of gust accelerations measured on the YF-12A airplane. The data were obtained during 90 flights at altitudes above 12.2 kilometers (40,000 feet). Subjective turbulence intensity ratings were obtained from air crew members. The air crew often rated given gust accelerations as being more intense during high altitude supersonic flight than during low altitude subsonic flight. The portion of flight distance in turbulence ranged from 6 percent to 8 percent at altitudes between 12.2 kilometers and 16.8 kilometers (40,000 feet and 55,000 feet) to less than 1 percent at altitudes above 18.3 kilometers (60,000 feet). The amount of turbulence varied with season, increasing by a factor of 3 or more from summer to winter. Given values of gust acceleration were less frequent, on the basis of distance traveled, for supersonic flight of the YF-12A airplane at altitudes above 12.2 kilometers (40,000 feet) than for subsonic flight of a jet passenger airplane at altitudes below 12.2 kilometers (40,000 feet). The median thickness of high altitude turbulence patches was less than 400 meters (1300 feet); the median length was less than 16 kilometers (10 miles). The distribution of the patch dimensions tended to be log normal.

5m RPV for Exploring Joined Wing Gust Response

DTIC Science & Technology

2009-12-01

an outer layer of light glass scrim used as the first layer. Varying layers of carbon cloth are used and then the core material is added. In this...for various angles of attack and sideslip angles. A parametric model is developed using Phoenix Integration’s Model Center Software (MC). This model...by the ground control software and finally a piece of real-time footage taken from the on-board, gimbaled camera. 2009 Progress Report 27

The influence of vehicle aerodynamic and control response characteristics on driver-vehicle performance

NASA Technical Reports Server (NTRS)

Alexandridis, A. A.; Repa, B. S.; Wierwille, W. W.

1978-01-01

The effects of changes in understeer, control sensitivity, and location of the lateral aerodynamic center of pressure (c.p.) of a typical passenger car on the driver's opinion and on the performance of the driver-vehicle system were studied in a moving-base driving simulator. Twelve subjects with no prior experience on the simulator and no special driving skills performed regulation tasks in the presence of both random and step wind gusts.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes Within Thunderstorms September 17, 1946 to September 18, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period September 17, 1946 to September 18, 1946 at Orlando, Fla. are presented herein. These data are summarized in tables I, II, and III, respectively, and are of the type presented in reference 1 for previous flights.

Wind Turbine Gust Prediction Using Remote Sensing Data

NASA Astrophysics Data System (ADS)

Towers, Paul; Jones, Bryn

2013-11-01

Offshore wind energy is a growing energy source as governments around the world look for environmentally friendly solutions to potential future energy shortages. In order to capture more energy from the wind, larger turbines are being designed, leading to the structures becoming increasingly vulnerable to damage caused by violent gusts of wind. Advance knowledge of such gusts will enable turbine control systems to take preventative action, reducing turbine maintenance costs. We present a system which can accurately forecast the velocity profile of an oncoming wind, given only limited spatial measurements from light detection and ranging (LiDAR) units, which are currently operational in industry. Our method combines nonlinear state estimation techniques with low-order models of atmospheric boundary-layer flows to generate flow-field estimates. We discuss the accuracy of our velocity profile predictions by direct comparison to data derived from large eddy simulations of the atmospheric boundary layer.

Wind vs. Dust Devil Streaks

NASA Technical Reports Server (NTRS)

2004-01-01

22 February 2004 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image presents a fine illustration of the difference between streaks made by dust devils and streaks made by wind gusts. Dust devils are usually solitary, spinning vortices. They resemble a tornado, or the swirling motion of a familiar, Tasmanian cartoon character. Wind gusts, on the other hand, can cover a larger area and affect more terrain at the same time. The dark, straight, and parallel features resembling scrape marks near the right/center of this image are thought to have been formed by a singular gust of wind, whereas the more haphazard dark streaks that crisscross the scene were formed by dozens of individual dust devils, acting at different times. This southern summer image is located in Noachis Terra near 67.0oS, 316.2oW. Sunlight illuminates the scene from the upper left; the picture covers an area 3 km (1.9 mi) wide.

Two Empirical Models for Land-falling Hurricane Gust Factors

NASA Technical Reports Server (NTRS)

Merceret, Franics J.

2008-01-01

Gaussian and lognormal models for gust factors as a function of height and mean windspeed in land-falling hurricanes are presented. The models were empirically derived using data from 2004 hurricanes Frances and Jeanne and independently verified using data from 2005 hurricane Wilma. The data were collected from three wind towers at Kennedy Space Center and Cape Canaveral Air Force Station with instrumentation at multiple levels from 12 to 500 feet above ground level. An additional 200-foot tower was available for the verification. Mean wind speeds from 15 to 60 knots were included in the data. The models provide formulas for the mean and standard deviation of the gust factor given the mean windspeed and height above ground. These statistics may then be used to assess the probability of exceeding a specified peak wind threshold of operational significance given a specified mean wind speed.

Pilot dynamics for instrument approach tasks: Full panel multiloop and flight director operations

NASA Technical Reports Server (NTRS)

Weir, D. H.; Mcruer, D. T.

1972-01-01

Measurements and interpretations of single and mutiloop pilot response properties during simulated instrument approach are presented. Pilot subjects flew Category 2-like ILS approaches in a fixed base DC-8 simulaton. A conventional instrument panel and controls were used, with simulated vertical gust and glide slope beam bend forcing functions. Reduced and interpreted pilot describing functions and remmant are given for pitch attitude, flight director, and multiloop (longitudinal) control tasks. The response data are correlated with simultaneously recorded eye scanning statistics, previously reported in NASA CR-1535. The resulting combined response and scanning data and their interpretations provide a basis for validating and extending the theory of manual control displays.

Effect of Frontal Gusts and Stroke Deviation in Forward Flapping Flight and Deconstructing the Aerodynamics of a Fruit Bat

NASA Astrophysics Data System (ADS)

Viswanath, Kamal

This dissertation broadly seeks to understand the effect different kinematic parameters, external forces, and dynamic wing conformation have on the fluid dynamics of flapping flight. The primary motivation is to better grasp the fundamental fluid phenomena driving efficient flapping flight in the Reynolds number regime of birds, bats, and man made fliers of similar scale. The CFD solver (GenIDLEST) used is a Navier-Stokes solver in a finite volume formulation on non-staggered structured multiblock meshes. It has the capability for both body-fitted moving grid simulations and Immersed Boundary Method (IBM) for simulating complex bodies moving within a fluid. To that purpose we investigate the response of a rigid flapping thin surface planar wing in forward flight, at Re=10,000, subjected to frontal gusts. Gusts are a common ecological hazard for flapping fliers, especially in crowded environments. Among the various temporal and spatial scales of gust possible, we look at the phasing and duration of very large spatial scale gusts and their impact on the unsteady fluid dynamics of flapping within a single flapping cycle. The gust is characterized by a step function with time scale much smaller than the flapping time period. Having the advantage of prescribing the motion, as well as the timing and duration of the gust, this allowed the observation of the effect of angle of attack (AOA) and wing rotation on the evolution of the Leading Edge Vortex (LEV) and, hence the instantaneous lift and thrust profiles, by varying the parameters. During the downstroke, frontal gusts accelerated the flow development resulting in early separation of existing LEVs and formation of new ones on the wing surface which influenced the force generation by increasing the lift and thrust. These phenomena underscored the importance of the unsteady vortex structures as the primary force generators in flapping flight. The effect of the gust is observed to be diminished when it occurs during rapid supination of the wing. Unlike the influence of the vortices during the downstroke, the upstroke primarily reacted to effective AOA changes. A key characteristic of the kinematics of fliers in nature is stroke deviation. We investigate this phenomenon using a similar framework as above on a rigid thin surface flat-plate flapping wing in forward flight. Stroke deviation happens due to a variety of factors including wing flexion, wing lateral translation, and wing area change and here we investigate the different stroke deviation trajectories. Various trajectories were analyzed to assess the different capabilities that such kinematics might offer. The instantaneous lift and thrust profiles were observed to be influenced by a combination of the Leading Edge Vortex (LEV) and the Trailing Edge Vortex (TEV) structures existing in the flow at any given time. As an index of the cost of performance across all cases, the power requirements for the different cases, based on the fluid torques, are analyzed. Anti-clockwise figure-of-eight-cycle deviation is shown to be very complex with high power costs while having better performance. The clockwise elliptic-cycle held promise in being utilized as a viable stroke deviation trajectory for forward flight over the base non stroke deviation case. Armed with insight gained from these simple flapping structures, we are able to conduct the analysis of the flapping flight data obtained on a fruit bat. Understanding the full complexity of bat flight and the ways in which bat flight differs from that of other vertebrate flight requires attention to the intricate functional mechanics and architecture of the wings and the resulting unsteady transient mechanisms of the flow around the wings. We extract the detailed kinematic motion of the bat wing from the recorded data and then simulate the bat wing motion in the CFD framework for a range of Reynolds numbers. The Strouhal number calculated from the data is high indicating that the flow physics is dominated by the oscillatory motion. From the data the bat exhibits fine control of its mechanics by actively varying wing camber, wing area, torsional rotation of the wing, forward and backward translational sweep of the wing, and wing conformation to dictate the fluid dynamics. As is common in flapping flight, the primary force generation is through the attached unsteady vortices on the wing surface. This force output is modulated by the bat through varying wing camber and the wing area. Proper orthogonal decomposition of the wing kinematics is undertaken to compile a simpler set of kinematic modes that can approximate the original motion used by the fruit bat. These modes are then analyzed based on aerodynamic performance and power cost for more efficient flight. Understanding the physics of these modes will help us use them as prescribed kinematics for mechanical flappers as well as improve upon them from nature.

Flying Drosophila stabilize their vision-based velocity controller by sensing wind with their antennae

PubMed Central

Fuller, Sawyer Buckminster; Straw, Andrew D.; Peek, Martin Y.; Murray, Richard M.; Dickinson, Michael H.

2014-01-01

Flies and other insects use vision to regulate their groundspeed in flight, enabling them to fly in varying wind conditions. Compared with mechanosensory modalities, however, vision requires a long processing delay (~100 ms) that might introduce instability if operated at high gain. Flies also sense air motion with their antennae, but how this is used in flight control is unknown. We manipulated the antennal function of fruit flies by ablating their aristae, forcing them to rely on vision alone to regulate groundspeed. Arista-ablated flies in flight exhibited significantly greater groundspeed variability than intact flies. We then subjected them to a series of controlled impulsive wind gusts delivered by an air piston and experimentally manipulated antennae and visual feedback. The results show that an antenna-mediated response alters wing motion to cause flies to accelerate in the same direction as the gust. This response opposes flying into a headwind, but flies regularly fly upwind. To resolve this discrepancy, we obtained a dynamic model of the fly’s velocity regulator by fitting parameters of candidate models to our experimental data. The model suggests that the groundspeed variability of arista-ablated flies is the result of unstable feedback oscillations caused by the delay and high gain of visual feedback. The antenna response drives active damping with a shorter delay (~20 ms) to stabilize this regulator, in exchange for increasing the effect of rapid wind disturbances. This provides insight into flies’ multimodal sensory feedback architecture and constitutes a previously unknown role for the antennae. PMID:24639532

Inventory of File nam.t00z.awp21100.tm00.grib2

Science.gov Websites

analysis Pressure Reduced to MSL [Pa] 002 surface GUST analysis Wind Speed (Gust) [m/s] 003 100 mb HGT -Component of Wind [m/s] 007.2 100 mb VGRD analysis V-Component of Wind [m/s] 008 150 mb HGT analysis Wind [m/s] 012.2 150 mb VGRD analysis V-Component of Wind [m/s] 013 200 mb HGT analysis Geopotential

Random harmonic analysis program, L221 (TEV156). Volume 1: Engineering and usage

NASA Technical Reports Server (NTRS)

Miller, R. D.; Graham, M. L.

1979-01-01

A digital computer program capable of calculating steady state solutions for linear second order differential equations due to sinusoidal forcing functions is described. The field of application of the program, the analysis of airplane response and loads due to continuous random air turbulence, is discussed. Optional capabilities including frequency dependent input matrices, feedback damping, gradual gust penetration, multiple excitation forcing functions, and a static elastic solution are described. Program usage and a description of the analysis used are presented.

Turbulence effects on a full-scale 2.5 MW horizontal axis wind turbine

NASA Astrophysics Data System (ADS)

Chamorro, Leonardo; Lee, Seung-Jae; Olsen, David; Milliren, Chris; Marr, Jeff; Arndt, Roger; Sotiropoulos, Fotis

2012-11-01

Power fluctuations and fatigue loads are among the most significant problems that wind turbines face throughout their lifetime. Turbulence is the common driving mechanism that triggers instabilities on these quantities. We investigate the complex response of a full-scale 2.5 MW wind turbine under nearly neutral thermal stratification. The study is performed in the EOLOS Wind Energy Research Field Station of the University of Minnesota. An instrumented 130 meter meteorological tower located upstream of a Clipper Liberty C96 wind turbine is used to characterize the turbulent flow and atmospheric conditions right upstream of the wind turbine. High resolution and synchronous measurements of the wind velocity, turbine power and strain at the tower foundation are used to determine the scale-to-scale interaction between flow and the wind turbine. The structure of the fluctuating turbine power and instantaneous stresses are studied in detail. Important insights about the role of turbulent and coherent motions as well as strong intermittent gusts will be discussed. Funding was provided by Department of Energy DOE (DE-EE0002980) and Xcel Energy through the Renewable Development Fund (grant RD3-42).

Atmospheric effects on inlets for supersonic cruise aircraft

NASA Technical Reports Server (NTRS)

Cole, G. L.

1977-01-01

Mixed-compression inlet dynamic behavior in the vicinity of unstart, was simulated and analyzed to investigate time response of an inlet's normal shock to independent disturbances in ambient temperature and pressure and relative velocity (longitudinal gust), with and without inlet controls active. The results indicate that atmospheric disturbances may be more important than internal disturbances in setting inlet controls requirements because they are usually not anticipated and because normal shock response to rapid atmospheric disturbances is not attenuated by the inlet, as it is for engine induced disturbances. However, before inlet control requirements can be fully assessed, more statistics on extreme atmospheric disturbances are needed.

A simulation investigation of scout/attack helicopter directional control requirements for hover and low-speed tasks

NASA Technical Reports Server (NTRS)

Bivens, Courtland C.; Guercio, Joseph G.

1987-01-01

A piloted simulator experiment was conducted to investigate directional axis handling qualities requirements for low speed and hover tasks performed by a Scout/Attack helicopter. Included were the directional characteristics of various candidate light helicopter family configurations. Also, the experiment focused on conventional single main/tail rotor configurations of the OH-58 series aircraft, where the first-order yaw-axis dynamic effects that contributed to the loss of tail rotor control were modeled. Five pilots flew 22 configurations under various wind conditions. Cooper-Harper handling quality ratings were used as the primary measure of merit of each configuration. The results of the experiment indicate that rotorcraft configurations with high directional gust sensitivity require greater minimum yaw damping to maintain satisfactory handling qualities during nap-of-the-Earth flying tasks. It was also determined that both yaw damping and control response are critical handling qualities parameters in performing the air-to-air target acquisition and tracking task. Finally, the lack of substantial yaw damping and larger values of gust sensitivity increased the possibility of loss of directional control at low airspeeds for the single main/tail rotor configurations.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms August 17, 1946 to August 19, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

Results obtained from gust and draft velocity measurements within thunderstorms for the period August 17, 1946 to August 19, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records taken on the present flights indicated that mo ambient-air temperature data were obtained.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms July 24, 1946 to August 6, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, Harold B.

1947-01-01

The results obtained from gust and draft velocity measurements within thunderstorms for the period July 24, 1946 to August 6, 1946 at Orlando, Florida are presented herein. These data are summarized in tables I and II and are of the type presented in reference 1 for previous flights. In two thunderstorm traverses, indications of ambient-air temperature were obtained from photo-observer records. These data are summarized in table III.

Aircraft Measurements of the Frequency of Turbulence Encounters in Australia, A Review and Assessment

DTIC Science & Technology

1981-03-01

weighting factors are given in column 6 of Table 1. 4 The data for three of the programs (NZ Viscount, Comet and 707) are either not available in the...data at high altitudes. 4 REFERENCES Aplin, J. E. (1964). Atmospheric turbulence encountered by Comet 2 aircraft carrying cloud collision warning...M2/518 folio 9. Kaynes, 1. W. (1971). Gust loads on Comet aircraft. RAE TR 71165. Kaynes, i. W. (1972). A summary of the analysis of gust loads

Roll paper pilot. [mathematical model for predicting pilot rating of aircraft in roll task

NASA Technical Reports Server (NTRS)

Naylor, F. R.; Dillow, J. D.; Hannen, R. A.

1973-01-01

A mathematical model for predicting the pilot rating of an aircraft in a roll task is described. The model includes: (1) the lateral-directional aircraft equations of motion; (2) a stochastic gust model; (3) a pilot model with two free parameters; and (4) a pilot rating expression that is a function of rms roll angle and the pilot lead time constant. The pilot gain and lead time constant are selected to minimize the pilot rating expression. The pilot parameters are then adjusted to provide a 20% stability margin and the adjusted pilot parameters are used to compute a roll paper pilot rating of the aircraft/gust configuration. The roll paper pilot rating was computed for 25 aircraft/gust configurations. A range of actual ratings from 2 to 9 were encountered and the roll paper pilot ratings agree quite well with the actual ratings. In addition there is good correlation between predicted and measured rms roll angle.

Dynamics and flight control of a flapping-wing robotic insect in the presence of wind gusts.

PubMed

Chirarattananon, Pakpong; Chen, Yufeng; Helbling, E Farrell; Ma, Kevin Y; Cheng, Richard; Wood, Robert J

2017-02-06

With the goal of operating a biologically inspired robot autonomously outside of laboratory conditions, in this paper, we simulated wind disturbances in a laboratory setting and investigated the effects of gusts on the flight dynamics of a millimetre-scale flapping-wing robot. Simplified models describing the disturbance effects on the robot's dynamics are proposed, together with two disturbance rejection schemes capable of estimating and compensating for the disturbances. The proposed methods are experimentally verified. The results show that these strategies reduced the root-mean-square position errors by more than 50% when the robot was subject to 80 cm s -1 horizontal wind. The analysis of flight data suggests that modulation of wing kinematics to stabilize the flight in the presence of wind gusts may indirectly contribute an additional stabilizing effect, reducing the time-averaged aerodynamic drag experienced by the robot. A benchtop experiment was performed to provide further support for this observed phenomenon.

Dynamics and flight control of a flapping-wing robotic insect in the presence of wind gusts

PubMed Central

Chen, Yufeng; Helbling, E. Farrell; Ma, Kevin Y.; Cheng, Richard; Wood, Robert J.

2017-01-01

With the goal of operating a biologically inspired robot autonomously outside of laboratory conditions, in this paper, we simulated wind disturbances in a laboratory setting and investigated the effects of gusts on the flight dynamics of a millimetre-scale flapping-wing robot. Simplified models describing the disturbance effects on the robot's dynamics are proposed, together with two disturbance rejection schemes capable of estimating and compensating for the disturbances. The proposed methods are experimentally verified. The results show that these strategies reduced the root-mean-square position errors by more than 50% when the robot was subject to 80 cm s−1 horizontal wind. The analysis of flight data suggests that modulation of wing kinematics to stabilize the flight in the presence of wind gusts may indirectly contribute an additional stabilizing effect, reducing the time-averaged aerodynamic drag experienced by the robot. A benchtop experiment was performed to provide further support for this observed phenomenon. PMID:28163872

An Experimental Device for Generating High Frequency Perturbations in Supersonic Wind Tunnels

NASA Technical Reports Server (NTRS)

Melcher, Kevin J.; Ibrahim, Mounir B.

1996-01-01

This paper describes the analytical study of a device that has been proposed as a mechanism for generating gust-like perturbations in supersonic wind tunnels. The device is envisioned as a means to experimentally validate dynamic models and control systems designed for high-speed inlets. The proposed gust generator is composed of two flat trapezoidal plates that modify the properties of the flow ingested by the inlet. One plate may be oscillated to generate small perturbations in the flow. The other plate is held stationary to maintain a constant angle-of-attack. Using an idealized approach, design equations and performance maps for the new device were developed from the compressible flow relations. A two-dimensional CFD code was used to confirm the correctness of these results. The idealized approach was then used to design and evaluate a new gust generator for a 3.05-meter by 3.05-meter (10-foot by 10-foot) supersonic wind tunnel.

Meteotsunami Detection with ASOS data

NASA Astrophysics Data System (ADS)

Kim, Y. Y.; Angove, M.

2017-12-01

A meteotsunami can strike almost any coast. Recent researches have shown that meteotsunamis are more common than previously thought and suggest that some past events may have been mistaken for other types of coastal floods, such as storm surges or seiches. In the United States, conditions for destructive meteotsunamis are most favorable along the East Coast, Gulf of Mexico, and in the Great Lakes, where they may pose a greater threat than earthquake-generated tsunamis. It is evident that meteotsunamis are strongly related to a mesoscale convective system or derecho of sufficient intensity and translational speed. Meteotsunamis are generated by pressure and wind disturbances related to the convective system above continental shelf area of the ocean. In this study it is noted that air pressure, wind gust speed, and air temperature display specific simultaneous changes favorable for meteotsunami development. Sudden wind gust rise, air pressure rise, and air temperature drop occur due to gust front related to cloud downdrafts. Therefore, we suggest that such a consistent tendency of wind gust speed, air pressure, and air temperature associated with mesoscale convective system capable of generating meteotsunami can be used for meteotsunami detection about one or two days before the event in the ocean. It was applied for the June 13, 2013 meteotsunami with automated surface observing systems (ASOS) meteorological data. For operational use of the detection of potential for meteotsunami development at U.S. East or Gulf of Mexico coasts in waters, detection threshold values for the three variables are also discussed.

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Vetter, Travis K.; Penning, Kevin B.; Coulson, David A.; Heeg, Jennifer.

2013-01-01

of a two part document. Part 2 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models, Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation." A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a semispan, aeroelastically scaled, wind tunnel model of a flying wing SensorCraft vehicle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree of freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid body modes. Gust load alleviation (GLA) and Body freedom flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Ground/Flight Correlation of Aerodynamic Loads with Structural Response

NASA Technical Reports Server (NTRS)

Mangalam, Arun S.; Davis, Mark C.

2009-01-01

Ground and flight tests provide a basis and methodology for in-flight characterization of the aerodynamic and structural performance through the monitoring of the fluid-structure interaction. The NF-15B flight tests of the Intelligent Flight Control System program provided a unique opportunity to test the correlation of aerodynamic loads with points of flow attaching and detaching from the surface, which are also known as flow bifurcation points, as observed in a previous wind tunnel test performed at the U.S. Air Force Academy (Colorado Springs, Colorado). Moreover, flight tests, along with the subsequent unsteady aerodynamic tests in the NASA Transonic Dynamics Tunnel (TDT), provide a basis using surface flow sensors as means of assessing the aeroelastic performance of flight vehicles. For the flight tests, the NF-15B tail was instrumented with hot-film sensors and strain gages for measuring root-bending strains. This data were gathered via selected sideslip maneuvers performed at level flight and subsonic speeds. The aerodynamic loads generated by the sideslip maneuver resulted in a structural response, which were then compared with the hot-film sensor signals. The hot-film sensor signals near the stagnation region were found to be highly correlated with the root-bending strains. For the TDT tests, a flexible wing section developed under the U.S. Air Force Research Lab SensorCraft program was instrumented with strain gages, accelerometers, and hot-film sensors at two span stations. The TDT tests confirmed the correlation between flow bifurcation points and the wing structural response to tunnel-generated gusts. Furthermore, as the wings structural modes were excited by the gusts, a gradual phase change between the flow bifurcation point and the structural mode occurred during a resonant condition.

Doppler-radar observation of the evolution of downdrafts in convective clouds

NASA Technical Reports Server (NTRS)

Motallebi, N.

1982-01-01

A detailed analysis of the 20 July 1977 thunderstorm complex which formed and evolve over the South Park region in Central Colorado is presented. The storm was extensively analyzed using multiple Doppler radar and surface mesonet data, developed within an environment having very weak wind shear. The storm owed its intensification to the strength of the downdraft, which was nearly coincident with the region where the cloud had grown. The noteworthy features of this storm were its motion to the right of the cloud-level winds, its multicellular nature and discrete propagation, its north-south orientation, and its relatively large storm size and high reflectivity factor (55 dBZ). This scenario accounts for the observed mesoscale and cloud-scale event. A line of convergence was generated at the interface between the easterly upslope winds and westerly winds. During stage II, the convergence line subsequently propagated down the slopes of the Mosquito Range, and was the main forcing mechanism for the development of updraft on the west flank of the storm. The formation of downdraft on the eastern side of updraft blacked surface inflow, and created a detectable gust front. As the original downdraft intensified, the accumulation of evaporatively-chilled air caused the intensification of the mesohigh, which likely destroyed the earlier convergence line and created a stronger convergence line to the east, which forced up-lifting of the moist, westerly inflow and caused the formation of updraft to the east. An organized downdraft circulation, apparently maintained by precipitation drag and evaporational cooling, was responsible in sustaining a well-defined gust front. The storm attained its highest intensity as a consequence of merging with a neighboring cloud. The interaction of downdrafts or gust fronts from two intense cells appeared to be the primary mechanism of this merging process as suggested by Simpson et al. (1980). The merging process coincided with more rain than occurred in unmerged echoes.

Maximized gust loads for a nonlinear airplane using matched filter theory and constrained optimization

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Pototzky, Anthony S.; Perry, Boyd, III

1991-01-01

Two matched filter theory based schemes are described and illustrated for obtaining maximized and time correlated gust loads for a nonlinear aircraft. The first scheme is computationally fast because it uses a simple 1-D search procedure to obtain its answers. The second scheme is computationally slow because it uses a more complex multi-dimensional search procedure to obtain its answers, but it consistently provides slightly higher maximum loads than the first scheme. Both schemes are illustrated with numerical examples involving a nonlinear control system.

A bivariate gamma probability distribution with application to gust modeling. [for the ascent flight of the space shuttle

NASA Technical Reports Server (NTRS)

Smith, O. E.; Adelfang, S. I.; Tubbs, J. D.

1982-01-01

A five-parameter gamma distribution (BGD) having two shape parameters, two location parameters, and a correlation parameter is investigated. This general BGD is expressed as a double series and as a single series of the modified Bessel function. It reduces to the known special case for equal shape parameters. Practical functions for computer evaluations for the general BGD and for special cases are presented. Applications to wind gust modeling for the ascent flight of the space shuttle are illustrated.

Maximized gust loads for a nonlinear airplane using matched filter theory and constrained optimization

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Perry, Boyd, III; Pototzky, Anthony S.

1991-01-01

This paper describes and illustrates two matched-filter-theory based schemes for obtaining maximized and time-correlated gust-loads for a nonlinear airplane. The first scheme is computationally fast because it uses a simple one-dimensional search procedure to obtain its answers. The second scheme is computationally slow because it uses a more complex multidimensional search procedure to obtain its answers, but it consistently provides slightly higher maximum loads than the first scheme. Both schemes are illustrated with numerical examples involving a nonlinear control system.

Cascade aeroacoustics including steady loading effects

NASA Astrophysics Data System (ADS)

Chiang, Hsiao-Wei D.; Fleeter, Sanford

A mathematical model is developed to analyze the effects of airfoil and cascade geometry, steady aerodynamic loading, and the characteristics of the unsteady flow field on the discrete frequency noise generation of a blade row in an incompressible flow. The unsteady lift which generates the noise is predicted with a complex first-order cascade convected gust analysis. This model was then applied to the Gostelow airfoil cascade and variations, demonstrating that steady loading, cascade solidity, and the gust direction are significant. Also, even at zero incidence, the classical flat plate cascade predictions are unacceptable.

Statistical analysis of general aviation VG-VGH data

NASA Technical Reports Server (NTRS)

Clay, L. E.; Dickey, R. L.; Moran, M. S.; Payauys, K. W.; Severyn, T. P.

1974-01-01

To represent the loads spectra of general aviation aircraft operating in the Continental United States, VG and VGH data collected since 1963 in eight operational categories were processed and analyzed. Adequacy of data sample and current operational categories, and parameter distributions required for valid data extrapolation were studied along with envelopes of equal probability of exceeding the normal load factor (n sub z) versus airspeed for gust and maneuver loads and the probability of exceeding current design maneuver, gust, and landing impact n sub z limits. The significant findings are included.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms: August 23, 1946 to September 4, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1946-01-01

This report presents the results obtained from gust and draft velocity measurements within thunderstorms for the period August 23, 1946 to September 4, 1946 at Orlando, Florida. These data are summarized in tables I end II and are of the type presented in reference 1 for previous flights. In several of the surveys, indications of ambient air temperature were obtained from photo-observer records. These data are summarized in table III.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms July 22, 1946 to July 23, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

The results obtained from measurements of gust and draft velocities within thunderstorms for the period July 22, 1946 to July 23, 1946 at Orlando, Florida, are presented herein. These data are summarized in tables I and II, respectively, and are of the type presented in reference 1 for previous flights. Inspection of photo-observer records for the flights indicated that no data on ambient air temperature variations within thunderstorms were obtained.

Joint probabilities of extreme precipitation and wind gusts in Germany

NASA Astrophysics Data System (ADS)

von Waldow, H.; Martius, O.

2012-04-01

Extreme meteorological events such as storms, heavy rain, floods, droughts and heat waves can have devastating consequences for human health, infrastructure and ecosystems. Concomitantly occurring extreme events might interact synergistically to produce a particularly hazardous impact. The joint occurrence of droughts and heat waves, for example, can have a very different impact on human health and ecosystems both in quantity and quality, than just one of the two extreme events. The co-occurrence of certain types of extreme events is plausible from physical and dynamical considerations, for example heavy precipitation and high wind speeds in the pathway of strong extratropical cyclones. The winter storm Kyrill not only caused wind gust speeds well in excess of 30 m/s across Europe, but also brought 24 h precipitation sums greater than the mean January accumulations in some regions. However, the existence of such compound risks is currently not accounted for by insurance companies, who assume independence of extreme weather events to calculate their premiums. While there are established statistical methods to model the extremes of univariate meteorological variables, the modelling of multidimensional extremes calls for an approach that is tailored to the specific problem at hand. A first step involves defining extreme bivariate wind/precipitation events. Because precipitation and wind gusts caused by the same cyclone or convective cell do not occur at exactly the same location and at the same time, it is necessary to find a sound definition of "extreme compound event" for this case. We present a data driven method to choose appropriate time and space intervals that define "concomitance" for wind and precipitation extremes. Based on station data of wind speed and gridded precipitation data, we arrive at time and space intervals that compare well with the typical time and space scales of extratropical cyclones, i.e. a maximum time lag of 1 day and a maximum distance of about 300 km between associated wind and rain events. After modelling extreme precipitation and wind separately, we explore the practicability of characterising their joint distribution using a bivariate threshold excess model. In particular, we present different dependence measures and report about the computational feasibility and available computer codes.

Using Buoy and Radar Data to Study Sudden Wind Gusts Over Coastal Regions

NASA Technical Reports Server (NTRS)

Priftis, Georgios; Chronis, Themis; Lang, Timothy J.

2017-01-01

Significant sudden wind gusts can pose a threat to aviation near the coastline, as well as small (sailing) boats and commercial ships approaching the ports. Such cases can result in wind speed changes of more than an order of magnitude within 5 minutes, which can then last up to 20 minutes or more. Although the constellation of scatterometers is a good means of studying maritime convection, those sudden gusts are not easily captured because of the low time resolution. The National Data Buoy Center (NDBC) provides continuous measurements of wind speed and direction along the US coastal regions every 6 minutes. Buoys are platforms placed at specific places on the seas, especially along coastlines, providing data for atmospheric and oceanic studies. Next Generation Radars (NEXRADs), after the recent upgrade of the network to dual-pol systems, offer enhanced capabilities to study atmospheric phenomena. NEXRADs provide continuous full-volume scans approximately every 5 minutes and therefore are close to the time resolution of the buoy measurements. Use of single- Doppler retrievals might also provide a means of further validation.

Wind gusts and plant aeroelasticity effects on the aerodynamics of pollen shedding: a hypothetical turbulence-initiated wind-pollination mechanism.

PubMed

Urzay, Javier; Llewellyn Smith, Stefan G; Thompson, Elinor; Glover, Beverley J

2009-08-21

Plant reproduction depends on pollen dispersal. For anemophilous (wind-pollinated) species, such as grasses and many trees, shedding pollen from the anther must be accomplished by physical mechanisms. The unknown nature of this process has led to its description as the 'paradox of pollen liberation'. A simple scaling analysis, supported by experimental measurements on typical wind-pollinated plant species, is used to estimate the suitability of previous resolutions of this paradox based on wind-gust aerodynamic models of fungal-spore liberation. According to this scaling analysis, the steady Stokes drag force is found to be large enough to liberate anemophilous pollen grains, and unsteady boundary-layer forces produced by wind gusts are found to be mostly ineffective since the ratio of the characteristic viscous time scale to the inertial time scale of acceleration of the wind stream is a small parameter for typical anemophilous species. A hypothetical model of a stochastic aeroelastic mechanism, initiated by the atmospheric turbulence typical of the micrometeorological conditions in the vicinity of the plant, is proposed to contribute to wind pollination.

Transient Performance of a Vertical Axis Wind Turbine

NASA Astrophysics Data System (ADS)

Onol, Aykut; Yesilyurt, Serhat

2016-11-01

A coupled CFD/rotor dynamics modeling approach is presented for the analysis of realistic transient behavior of a height-normalized, three-straight-bladed VAWT subject to inertial effects of the rotor and generator load which is manipulated by a feedback control under standardized wind gusts. The model employs the k- ɛ turbulence model to approximate unsteady Reynolds-averaged Navier-Stokes equations and is validated with data from field measurements. As distinct from related studies, here, the angular velocity is calculated from the rotor's equation of motion; thus, the dynamic response of the rotor is taken into account. Results include the following: First, the rotor's inertia filters large amplitude oscillations in the wind torque owing to the first-order dynamics. Second, the generator and wind torques differ especially during wind transients subject to the conservation of angular momentum of the rotor. Third, oscillations of the power coefficient exceed the Betz limit temporarily due to the energy storage in the rotor, which acts as a temporary buffer that stores the kinetic energy like a flywheel in short durations. Last, average of transient power coefficients peaks at a smaller tip-speed ratio for wind gusts than steady winds. This work was supported by the Sabanci University Internal Research Grant Program (SU-IRG-985).

Investigations of simulated aircraft flight through thunderstorm outflows

NASA Technical Reports Server (NTRS)

Frost, W.; Crosby, B.

1978-01-01

The effects of wind shear on aircraft flying through thunderstorm gust fronts were investigated. A computer program was developed to solve the two dimensional, nonlinear equations of aircraft motion, including wind shear. The procedure described and documented accounts for spatial and temporal variations of the aircraft within the flow regime. Analysis of flight paths and control inputs necessary to maintain specified trajectories for aircraft having characteristics of DC-8, B-747, augmentor wing STOL, and DHC-6 aircraft was recorded. From the analysis an attempt was made to find criteria for reduction of the hazards associated with landing through thunderstorm gust fronts.

Epidemiology of injuries due to tropical cyclones in Hong Kong: a retrospective observational study.

PubMed

Rotheray, K R; Aitken, P; Goggins, W B; Rainer, T H; Graham, C A

2012-12-01

Tropical cyclones are huge circulating masses of wind which form over tropical and sub-tropical waters. They affect an average of 78 million people each year. Hong Kong is a large urban centre with a population of just over 7 million which is frequently affected by tropical cyclones. We aimed to describe the numbers and types of injuries due to tropical cyclones in Hong Kong, as well as their relation to tropical cyclone characteristics. The records of all patients presenting to Hong Kong's public hospital emergency departments from 1st January 2004 to 31st December 2009 with tropical cyclone related injuries were reviewed and information regarding patient and injury characteristics was collected. Meteorological records for the relevant periods were examined and data on wind speed, rainfall and timing of landfall and warning signals was recorded and compared with the timing of tropical cyclone related injuries. A total of 460 tropical cyclone related injuries and one fatality across 15 emergency departments were identified during the study period. The mean age of those injured was 48 years and 48% were female. 25.4% of injuries were work related. The head (33.5%) and upper limb (32.5%) were the most commonly injured regions, with contusions (48.6%) and lacerations (30.2%) being the most common injury types. Falls (42.6%) were the most common mechanism of injury, followed by being hit by a falling or flying object (22.0%). In univariable analysis the relative risk of injury increased with mean hourly wind speed and hourly maximum gust. Multivariable analysis, however, showed that relative risk of injury increased with maximum gust but not average wind speed, with relative risk of injury rising sharply above maximum gusts of greater than 20 m/s. Moderate wind speed with high gust (rather than high average and high gust) appears to be the most risky situation for injuries. Relative risk of injury was not associated with rainfall. The majority of injuries (56%) occurred in the 3h before and after a tropical cyclone's closest proximity to Hong Kong, with relative risk of injury being highest mid-morning. In tropical cyclone related injuries in Hong Kong the head and upper limb are the most commonly affected sites with falls and being hit by a falling or flying object being the most common mechanisms of injury. Hourly maximum gust appears to be more important that mean hourly wind speed in determining risk of injury. These findings have implications for injury prevention measures and emergency planning in Hong Kong and other regions effected by tropical cyclones. Copyright © 2011 Elsevier Ltd. All rights reserved.

Parachute dynamics and stability analysis. [using nonlinear differential equations of motion

NASA Technical Reports Server (NTRS)

Ibrahim, S. K.; Engdahl, R. A.

1974-01-01

The nonlinear differential equations of motion for a general parachute-riser-payload system are developed. The resulting math model is then applied for analyzing the descent dynamics and stability characteristics of both the drogue stabilization phase and the main descent phase of the space shuttle solid rocket booster (SRB) recovery system. The formulation of the problem is characterized by a minimum number of simplifying assumptions and full application of state-of-the-art parachute technology. The parachute suspension lines and the parachute risers can be modeled as elastic elements, and the whole system may be subjected to specified wind and gust profiles in order to assess their effects on the stability of the recovery system.

Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 2: A Centerline Supported Fullspan Model Tested for Gust Load Alleviation

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Vetter, Travis K.; Penning, Kevin B.; Coulson, David A.; Heeg, Jennifer

2014-01-01

This is part 2 of a two part document. Part 1 is titled: "Aeroservoelastic Testing of Free Flying Wind Tunnel Models Part 1: A Sidewall Supported Semispan Model Tested for Gust Load Alleviation and Flutter Suppression." A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, flexible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind tunnel model of a joined wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind tunnel model was mated to a new, two degree of freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at10 percent static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be flown in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free flying wind tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Warm-season severe wind events in Germany

NASA Astrophysics Data System (ADS)

Gatzen, Christoph

2013-04-01

A 15-year data set of wind measurements was analyzed with regard to warm season severe wind gusts in Germany. For April to September of the years 1997 to 2011, 1035 wind measurements of 26 m/s or greater were found. These wind reports were associated with 268 wind events. In total, 252 convective wind events contributed to 837 (81%) of the wind reports, 16 non-convective synoptic-scale wind events contributed to 198 reports (19%). Severe wind events were found with synoptic situations characterized by rather strong mid-level flow and advancing mid-level troughs. Severe convective wind events were analyzed using radar images and classified with respect to the observed radar structure. The most important convective mode was squall lines that were associated with one third of all severe wind gusts, followed by groups, bow echo complexes, and bow echoes. Supercells and cells were not associated with many wind reports. The low contribution of isolated cells indicates that rather large-scale forcing by synoptic-scale features like fronts is important for German severe wind events. Bow echoes were found to be present for 58% of all wind reports. The movement speed of bow echoes indicated a large variation with a maximum speed of 33 m/s. Extreme wind events as well as events with more than 15 wind reports were found to be related to higher movement speeds. Concentrating on the most intense events, derechos seem to be very important to the warm season wind threat in Germany. Convective events with a path length of more than 400 km contributed to 36% of all warm-season wind gusts in this data set. Furthermore, eight of nine extreme gusts exceeding 40 m/s were recorded with derecho events.

Operation Redwing -- Project 5. 2. In-flight participation of a B-52. Report for May-July 1956

DOE Office of Scientific and Technical Information (OSTI.GOV)

Williams, F.L.

1985-04-01

The primary objective of this Project was to obtain measured-energy input and aircraft-response data on an instrumented B-52 aircraft when subjected to the thermal, blast, and gust effects of a nuclear explosion. To accomplish this, analysis was used in selecting the spatial location for the B-52, relative to a detonation, that would result in the desired aircraft inputs and responses. The B-52 was extensively instrumented with the major portion of the instrumentation devoted to measuring aircraft responses. The B-52 participated in nine shots, including one shot which the aircraft aborted just prior to time zero because of Bombing Navigation Systemmore » difficulties. The reliability of the instrumentation system was between 95% and 100% throughout the test program.« less

A linearized Euler analysis of unsteady flows in turbomachinery

NASA Technical Reports Server (NTRS)

Hall, Kenneth C.; Crawley, Edward F.

1987-01-01

A method for calculating unsteady flows in cascades is presented. The model, which is based on the linearized unsteady Euler equations, accounts for blade loading shock motion, wake motion, and blade geometry. The mean flow through the cascade is determined by solving the full nonlinear Euler equations. Assuming the unsteadiness in the flow is small, then the Euler equations are linearized about the mean flow to obtain a set of linear variable coefficient equations which describe the small amplitude, harmonic motion of the flow. These equations are discretized on a computational grid via a finite volume operator and solved directly subject to an appropriate set of linearized boundary conditions. The steady flow, which is calculated prior to the unsteady flow, is found via a Newton iteration procedure. An important feature of the analysis is the use of shock fitting to model steady and unsteady shocks. Use of the Euler equations with the unsteady Rankine-Hugoniot shock jump conditions correctly models the generation of steady and unsteady entropy and vorticity at shocks. In particular, the low frequency shock displacement is correctly predicted. Results of this method are presented for a variety of test cases. Predicted unsteady transonic flows in channels are compared to full nonlinear Euler solutions obtained using time-accurate, time-marching methods. The agreement between the two methods is excellent for small to moderate levels of flow unsteadiness. The method is also used to predict unsteady flows in cascades due to blade motion (flutter problem) and incoming disturbances (gust response problem).

Wind-Tunnel Survey of an Oscillating Flow Field for Application to Model Helicopter Rotor Testing

NASA Technical Reports Server (NTRS)

Mirick, Paul H.; Hamouda, M-Nabil H.; Yeager, William T., Jr.

1990-01-01

A survey was conducted of the flow field produced by the Airstream Oscillator System (AOS) in the Langley Transonic Dynamics Tunnel (TDT). The magnitude of a simulated gust field was measured at 15 locations in the plane of a typical model helicopter rotor when tested in the TDT using the Aeroelastic Rotor Experimental System (ARES) model. These measurements were made over a range of tunnel dynamic pressures typical of those used for an ARES test. The data indicate that the gust field produced by the AOS is non-uniform across the tunnel test section, but should be sufficient to excite a model rotor.

Symmetric airfoil geometry effects on leading edge noise.

PubMed

Gill, James; Zhang, X; Joseph, P

2013-10-01

Computational aeroacoustic methods are applied to the modeling of noise due to interactions between gusts and the leading edge of real symmetric airfoils. Single frequency harmonic gusts are interacted with various airfoil geometries at zero angle of attack. The effects of airfoil thickness and leading edge radius on noise are investigated systematically and independently for the first time, at higher frequencies than previously used in computational methods. Increases in both leading edge radius and thickness are found to reduce the predicted noise. This noise reduction effect becomes greater with increasing frequency and Mach number. The dominant noise reduction mechanism for airfoils with real geometry is found to be related to the leading edge stagnation region. It is shown that accurate leading edge noise predictions can be made when assuming an inviscid meanflow, but that it is not valid to assume a uniform meanflow. Analytic flat plate predictions are found to over-predict the noise due to a NACA 0002 airfoil by up to 3 dB at high frequencies. The accuracy of analytic flat plate solutions can be expected to decrease with increasing airfoil thickness, leading edge radius, gust frequency, and Mach number.

Description of a Normal-Force In-Situ Turbulence Algorithm for Airplanes

NASA Technical Reports Server (NTRS)

Stewart, Eric C.

2003-01-01

A normal-force in-situ turbulence algorithm for potential use on commercial airliners is described. The algorithm can produce information that can be used to predict hazardous accelerations of airplanes or to aid meteorologists in forecasting weather patterns. The algorithm uses normal acceleration and other measures of the airplane state to approximate the vertical gust velocity. That is, the fundamental, yet simple, relationship between normal acceleration and the change in normal force coefficient is exploited to produce an estimate of the vertical gust velocity. This simple approach is robust and produces a time history of the vertical gust velocity that would be intuitively useful to pilots. With proper processing, the time history can be transformed into the eddy dissipation rate that would be useful to meteorologists. Flight data for a simplified research implementation of the algorithm are presented for a severe turbulence encounter of the NASA ARIES Boeing 757 research airplane. The results indicate that the algorithm has potential for producing accurate in-situ turbulence measurements. However, more extensive tests and analysis are needed with an operational implementation of the algorithm to make comparisons with other algorithms or methods.

A Study of the Effects of Large Scale Gust Generation in a Small Scale Atmospheric Wind Tunnel: Application to Micro Aerial Vehicles

NASA Astrophysics Data System (ADS)

Roadman, Jason; Mohseni, Kamran

2009-11-01

Modern technology operating in the atmospheric boundary layer could benefit from more accurate wind tunnel testing. While scaled atmospheric boundary layer tunnels have been well developed, tunnels replicating portions of the turbulence of the atmospheric boundary layer at full scale are a comparatively new concept. Testing at full-scale Reynolds numbers with full-scale turbulence in an ``atmospheric wind tunnel'' is sought. Many programs could utilize such a tool including that of Micro Aerial Vehicles (MAVs) and other unmanned aircraft, the wind energy industry, fuel efficient vehicles, and the study of bird and insect fight. The construction of an active ``gust generator'' for a new atmospheric tunnel is reviewed and the turbulence it generates is measured utilizing single and cross hot wires. Results from this grid are compared to atmospheric turbulence and it is shown that various gust strengths can be produced corresponding to days ranging from calm to quite gusty. An initial test is performed in the atmospheric wind tunnel whereby the effects of various turbulence conditions on transition and separation on the upper surface of a MAV wing is investigated using oil flow visualization.

The inviscid pressure field on the tip of a semi-infinite wing and its application to the formation of a tip vortex

NASA Technical Reports Server (NTRS)

Hall, G. F.; Shamroth, S. J.; Mcdonald, H.; Briley, W. R.

1976-01-01

A method was developed for determining the aerodynamic loads on the tip of an infinitely thin, swept, cambered semi-infinite wing at an angle of attack which is operating subsonically in an inviscid medium and is subjected to a sinusoidal gust. Under the assumption of linearized aerodynamics, the loads on the tip are obtained by superposition of the steady aerodynamic results for angle of attack and camber, and the unsteady results for the response to the sinusoidal gust. The near field disturbance pressures in the fluid surrounding the tip are obtained by assuming a dipole representation for the loading on the tip and calculating the pressures accordingly. The near field pressures are used to drive a reduced form of the Navier-Stokes equations which yield the tip vortex formation. The combined viscid-inviscid analysis is applied to determining the pressures and examining the vortex rollup in the vicinity of an unswept, uncambered wing moving steadily at a Mach number of 0.2 at an angle of attack of 0.1 rad. The viscous tip flow calculation shows features expected in the tip flow such as the qualitatively proper development of boundary layers on both the upper and lower airfoil surfaces. In addition, application of the viscous solution leads to the generation of a circular type flow pattern above the airfoil suction surface.

Tropical Cyclone Indlala

NASA Technical Reports Server (NTRS)

2007-01-01

On March 14, 2007, storm-weary Madagascar braced for its fourth land-falling tropical cyclone in as many months. Cyclone Indlala was hovering off the island's northeast coast when the Moderate Resolution Imaging Spectroradiometer (MODIS) on NASA's Aqua satellite captured this photo-like image at 1:40 p.m. local time (10:40 UTC). Just over a hundred kilometers offshore, the partially cloudy eye at the heart of the storm seems like a vast drain sucking in a disk of swirling clouds. According to reports from the Joint Typhoon Warning Center issued less than three hours after MODIS captured this image, Indlala had winds of 115 knots (132 miles per hour), with gusts up to 140 knots (161 mph). Wave heights were estimated to be 36 feet. At the time of the report, the storm was predicted to intensify through the subsequent 12-hour period, to turn slightly southwest, and to strike eastern Madagascar as a Category 4 storm with sustained winds up to 125 knots (144 mph), and gusts up to 150 knots (173 mph). According to Reuters AlertNet news service, Madagascar's emergency response resources were taxed to their limit in early March 2007 as a result of extensive flooding in the North, drought and food shortages in the South, and three previous hits from cyclones in the preceding few months: Bondo in December 2006, Clovis in January 2007, and Gamede in February.

Evaluation of advanced airship concepts

NASA Technical Reports Server (NTRS)

Joner, B. A.; Schneider, J. J.

1975-01-01

A historical overview of the airship, technical and operational characteristics of conventional and hybrid concepts, and the results of a parametric design analysis and evaluation are presented. The lift capabilities of certain buoyant fluids for a hypothetical 16 million cu.ft. volume airship are compared. The potential advanced airship concepts are surveyed, followed by a discussion of the six configurations: conventional nonrigid, conventional rigid, Deltoid (Dynairship), Guppoid (Megalifter), Helipsoid, and Heli-Stat. It is suggested that a partially buoyant Helipsoid concept of the optimum buoyancy ratio has the potential to solve the problems facing future airship development, such as Ballast and Ballast Recovery System, Full Low-Speed Controllability, Susceptibility to Wind/Gusting, Weather/Icing Constraints, Ground Handling/Hangaring, and Direct/Indirect Operating Costs.

ASCENT Program

NASA Technical Reports Server (NTRS)

Brown, Richard; Collier, Gary; Heckenlaible, Richard; Dougherty, Edward; Dolenz, James; Ross, Iain

2012-01-01

The ASCENT program solves the three-dimensional motion and attendant structural loading on a flexible vehicle incorporating, optionally, an active analog thrust control system, aerodynamic effects, and staging of multiple bodies. ASCENT solves the technical problems of loads, accelerations, and displacements of a flexible vehicle; staging of the upper stage from the lower stage; effects of thrust oscillations on the vehicle; a payload's relative motion; the effect of fluid sloshing on vehicle; and the effect of winds and gusts on the vehicle (on the ground or aloft) in a continuous analysis. The ATTACH ASCENT Loads program reads output from the ASCENT flexible body loads program, and calculates the approximate load indicators for the time interval under consideration. It calculates the load indicator values from pre-launch to the end of the first stage.

Development of a wind energy converter with single blade rotor

NASA Astrophysics Data System (ADS)

Hipp, K.

1984-06-01

Wind energy converters with high tip speed ratio and a capacity of up to 50 kW in a 8.5 /msec wind speed were developed. Units with 12 m diameter rotors were tested. The concept of a cost favorable plant as a high speed engine with a supercritically running one blade rotor (soft bearing), gust balance out, automatic blade adjustment to ensure favorable starting qualities, proves to be a success. The single rectangular blade non-twisted with the profile NACA 23012/18 has no dynamic problems. The application of a centrifugal governor, i.e., vane like a Maxwell slat, operating only by rotation about a fixed hinge axis in order to attain adequate constant rotational speed of the plant, is not satisfactory.

A dynamic response and eye scanning data base useful in the development of theories and methods for the description of control/display relationships

NASA Technical Reports Server (NTRS)

Klein, R.

1972-01-01

A set of specially prepared digital tapes is reported which contain synchronized measurements of pilot scanning behavior, control response, and vehicle response obtained during instrument landing system approaches made in a fixed-base DC-8 transport simulator. The objective of the master tape is to provide a common data base which can be used by the research community to test theories, models, and methods for describing and analyzing control/display relations and interactions. The experimental conditions and tasks used to obtain the data and the detailed format of the tapes are described. Conventional instrument panel and controls were used, with simulated vertical gust and glide slope beam bend forcing functions. Continuous pilot eye fixations and scan traffic on the panel were measured. Both flight director and standard localizer/glide slope types of approaches were made, with both fixed and variable instrument range sensitivities.

Flutter and Forced Response Analyses of Cascades using a Two-Dimensional Linearized Euler Solver

NASA Technical Reports Server (NTRS)

Reddy, T. S. R.; Srivastava, R.; Mehmed, O.

1999-01-01

Flutter and forced response analyses for a cascade of blades in subsonic and transonic flow is presented. The structural model for each blade is a typical section with bending and torsion degrees of freedom. The unsteady aerodynamic forces due to bending and torsion motions. and due to a vortical gust disturbance are obtained by solving unsteady linearized Euler equations. The unsteady linearized equations are obtained by linearizing the unsteady nonlinear equations about the steady flow. The predicted unsteady aerodynamic forces include the effect of steady aerodynamic loading due to airfoil shape, thickness and angle of attack. The aeroelastic equations are solved in the frequency domain by coupling the un- steady aerodynamic forces to the aeroelastic solver MISER. The present unsteady aerodynamic solver showed good correlation with published results for both flutter and forced response predictions. Further improvements are required to use the unsteady aerodynamic solver in a design cycle.

Tornadogenesis via squall line and supercell interaction revisited - The 15 November 1989 Huntsville tornado

NASA Technical Reports Server (NTRS)

Goodman, Steven J.; Knupp, Kevin R.

1990-01-01

A case study analyzing the environmental setting and storm system morphology that provides observational evidence of a mechanism involving the interaction of a gust front with a preexisting mesocyclone is presented. This case serves to reemphasize the existence of a high conditional probability of tornado occurrence, given the merger of a gust front (or storm outflow) with a moderate to strong thunderstorm ahead of it. The resultant data serve to illustrate some important unresolved issues relevant to the severe weather warning system that involve the present and planned local warning and network radars, and future algorithms that might intelligently integrate other data sources and models with the radar data.

Load and dynamic assessment of B-52B-008 carrier aircraft for finned configuration 1 space shuttle solid rocket booster decelerator subsystem drop test vehicle. Volume 2: Airplane flutter and load analysis results

NASA Technical Reports Server (NTRS)

Quade, D. A.

1978-01-01

The airplane flutter and maneuver-gust load analysis results obtained during B-52B drop test vehicle configuration (with fins) evaluation are presented. These data are presented as supplementary data to that given in Volume 1 of this document. A brief mathematical description of airspeed notation and gust load factor criteria are provided as a help to the user. References are defined which provide mathematical description of the airplane flutter and load analysis techniques. Air-speed-load factor diagrams are provided for the airplane weight configurations reanalyzed for finned drop test vehicle configuration.

Effects of automobile steering characteristics on driver vehicle system dynamics in regulation tasks

NASA Technical Reports Server (NTRS)

Mcruer, D. T.; Klein, R.

1975-01-01

A regulation task which subjected the automobile to a random gust disturbance which is countered by driver control action is used to study the effects of various automobile steering characteristics on the driver/vehicle system. The experiments used a variable stability automobile specially configured to permit insertion of the simulated gust disturbance and the measurement of the driver/vehicle system characteristics. Driver/vehicle system dynamics were measured and interpreted as an effective open loop system describing function. Objective measures of system bandwidth, stability, and time delays were deduced and compared. These objective measures were supplemented by driver ratings. A tentative optimum range of vehicle dynamics for the directional regulation task was established.

Horizontal geometrical reaction time model for two-beam nacelle LiDARs

NASA Astrophysics Data System (ADS)

Beuth, Thorsten; Fox, Maik; Stork, Wilhelm

2015-06-01

Wind energy is one of the leading sustainable energies. To attract further private and state investment in this technology, a broad scaled drop of the cost of energy has to be enforced. There is a trend towards using Laser Doppler Velocimetry LiDAR systems for enhancing power output and minimizing downtimes, fatigue and extreme forces. Since most used LiDARs are horizontally setup on a nacelle and work with two beams, it is important to understand the geometrical configuration which is crucial to estimate reaction times for the actuators to compensate wind gusts. In the beginning of this article, the basic operating modes of wind turbines are explained and the literature on wind behavior is analyzed to derive specific wind speed and wind angle conditions in relation to the yaw angle of the hub. A short introduction to the requirements for the reconstruction of the wind vector length and wind angle leads to the problem of wind shear detection of angled but horizontal homogeneous wind fronts due to the spatial separation of the measuring points. A distance is defined in which the wind shear of such homogeneous wind fronts is not present which is used as a base to estimate further distance calculations. The reaction time of the controller and the actuators are having a negative effect on the effective overall reaction time for wind regulation as well. In the end, exemplary calculations estimate benefits and disadvantages of system parameters for wind gust regulating LiDARs for a wind turbine of typical size. An outlook shows possible future improvements concerning the vertical wind behavior.

Using C-Band Dual-Polarization Radar Signatures to Improve Convective Wind Forecasting at Cape Canaveral Air Force Station and NASA Kennedy Space Center

NASA Technical Reports Server (NTRS)

Amiot, Corey G.; Carey, Lawrence D.; Roeder, William P.; McNamara, Todd M.; Blakeslee, Richard J.

2017-01-01

The United States Air Force's 45th Weather Squadron (45WS) is the organization responsible for monitoring atmospheric conditions at Cape Canaveral Air Force Station and NASA Kennedy Space Center (CCAFS/KSC) and issuing warnings for hazardous weather conditions when the need arises. One such warning is issued for convective wind events, for which lead times of 30 and 60 minutes are desired for events with peak wind gusts of 35 knots or greater (i.e., Threshold-1) and 50 knots or greater (i.e., Threshold-2), respectively (Roeder et al. 2014).

European extra-tropical storm damage risk from a multi-model ensemble of dynamically-downscaled global climate models

NASA Astrophysics Data System (ADS)

Haylock, M. R.

2011-10-01

Uncertainty in the return levels of insured loss from European wind storms was quantified using storms derived from twenty-two 25 km regional climate model runs driven by either the ERA40 reanalyses or one of four coupled atmosphere-ocean global climate models. Storms were identified using a model-dependent storm severity index based on daily maximum 10 m wind speed. The wind speed from each model was calibrated to a set of 7 km historical storm wind fields using the 70 storms with the highest severity index in the period 1961-2000, employing a two stage calibration methodology. First, the 25 km daily maximum wind speed was downscaled to the 7 km historical model grid using the 7 km surface roughness length and orography, also adopting an empirical gust parameterisation. Secondly, downscaled wind gusts were statistically scaled to the historical storms to match the geographically-dependent cumulative distribution function of wind gust speed. The calibrated wind fields were run through an operational catastrophe reinsurance risk model to determine the return level of loss to a European population density-derived property portfolio. The risk model produced a 50-yr return level of loss of between 0.025% and 0.056% of the total insured value of the portfolio.

Observational study of surface wind along a sloping surface over mountainous terrain during winter

NASA Astrophysics Data System (ADS)

Lee, Young-Hee; Lee, Gyuwon; Joo, Sangwon; Ahn, Kwang-Deuk

2018-03-01

The 2018 Winter Olympic and Paralympic Games will be held in Pyeongchang, Korea, during February and March. We examined the near surface winds and wind gusts along the sloping surface at two outdoor venues in Pyeongchang during February and March using surface wind data. The outdoor venues are located in a complex, mountainous terrain, and hence the near-surface winds form intricate patterns due to the interplay between large-scale and locally forced winds. During February and March, the dominant wind at the ridge level is westerly; however, a significant wind direction change is observed along the sloping surface at the venues. The winds on the sloping surface are also influenced by thermal forcing, showing increased upslope flow during daytime. When neutral air flows over the hill, the windward and leeward flows show a significantly different behavior. A higher correlation of the wind speed between upper- and lower-level stations is shown in the windward region compared with the leeward region. The strong synoptic wind, small width of the ridge, and steep leeward ridge slope angle provide favorable conditions for flow separation at the leeward foot of the ridge. The gust factor increases with decreasing surface elevation and is larger during daytime than nighttime. A significantly large gust factor is also observed in the leeward region.

Fatigue Tests with Random Flight Simulation Loading

NASA Technical Reports Server (NTRS)

Schijve, J.

1972-01-01

Crack propagation was studied in a full-scale wing structure under different simulated flight conditions. Omission of low-amplitude gust cycles had a small effect on the crack rate. Truncation of the infrequently occurring high-amplitude gust cycles to a lower level had a noticeably accelerating effect on crack growth. The application of fail-safe load (100 percent limit load) effectively stopped subsequent crack growth under resumed flight-simulation loading. In another flight-simulation test series on sheet specimens, the variables studied are the design stress level and the cyclic frequency of the random gust loading. Inflight mean stresses vary from 5.5 to 10.0 kg/sq mm. The effect of the stress level is larger for the 2024 alloy than for the 7075 alloy. Three frequencies were employed: namely, 10 cps, 1 cps, and 0.1 cps. The frequency effect was small. The advantages and limitations of flight-simulation tests are compared with those of alternative test procedures such as constant-amplitude tests, program tests, and random-load tests. Various testing purposes are considered. The variables of flight-simulation tests are listed and their effects are discussed. A proposal is made for performing systematic flight-simulation tests in such a way that the compiled data may be used as a source of reference.

Noise generated by convected gusts interacting with swept airfoil cascades

NASA Astrophysics Data System (ADS)

Envia, E.; Kerschen, E. J.

1986-07-01

An analysis is developed for the noise generated by the interaction of a rotor viscous wake with a cascade of swept stator vanes. The stator vanes span a channel formed by infinite parallel walls and containing a subsonic mean flow. High frequency interactions, for which the noise generation is concentrated at the vane leading edge, are considered. The analysis utilizes a superposition of the solution to the isolated stator vane problem, presented in an earlier paper, to develop an approximate solution to the cascade problem. The rotor wake model includes the features of wake circumferential lean and a linear spanwise variation of the magnitude of the wake deficit velocity. Calculations are presented which show that, for rotor wakes with moderate circumferential lean, stator sweep produces substantial reductions in noise level. The vane sweep must be oriented to enhance the phase lags along the vane leading edge produced by wake lean. The noise levels are found to be fairly insensitive to spanwise variations in the wake deficit.

Measurements of Complex Oceanic Flows, from Turbulence in the Coastal Ocean to Interaction of Zooplankton with its Local Environment

NASA Astrophysics Data System (ADS)

Katz, J.

2004-03-01

The presentation has two parts, both dealing with flow structure, turbulence and flow-particle interactions in the ocean. The first part examines PIV data obtained in the bottom boundary layer of the coastal ocean in periods when the mean currents are higher, of the same order and weaker than the wave induced motions. The energy spectra display substantial anisotropy at all scales, and the flow consists of periods of "gusts" dominated by large vortical structures, separated by periods of quiescent flows. The frequency of these gusts increases with Reynolds number, and they disappear when the currents are weak. Conditional sampling shows that the Reynolds shear stress, and as a result the shear production, are generated only during periods of gusts. When the mean flow is weak and during quiescent periods of moderate flow the shear stresses are essentially zero. Dissipation, on the other hand, occurs continuously, and increases only slightly during gust periods. The second part focuses on interactions of zooplankton with the local flow. Digital in-line holographic cinematography is used for measuring the three-dimensional trajectory of a free-swimming copepod, and simultaneously the instantaneous 3-D velocity field around this copepod. The velocity field and trajectory of particles entrained by the copepod have a recirculating pattern in the copepod's frame of reference. This pattern is caused by the copepod sinking at a rate that is lower than its terminal sinking speed, due to the propulsive force generated by its feeding current. Consequently, the copepod has to hop periodically to scan different fluid for food. Using Stokeslets to model the velocity field, the measured velocity distributions enable us to estimate the excess weight of the copepod and the propulsive force generated by its feeding appendages. Sponsored in part by the Office of Naval Research and by the National Science Foundation.

Wind Tunnel Testing of Microtabs and Microjets for Active Load Control of Wind Turbine Blades

NASA Astrophysics Data System (ADS)

Cooperman, Aubryn Murray

Increases in wind turbine size have made controlling loads on the blades an important consideration for future turbine designs. One approach that could reduce extreme loads and minimize load variation is to incorporate active control devices into the blades that are able to change the aerodynamic forces acting on the turbine. A wind tunnel model has been constructed to allow testing of different active aerodynamic load control devices. Two such devices have been tested in the UC Davis Aeronautical Wind Tunnel: microtabs and microjets. Microtabs are small surfaces oriented perpendicular to an airfoil surface that can be deployed and retracted to alter the lift coefficient of the airfoil. Microjets produce similar effects using air blown perpendicular to the airfoil surface. Results are presented here for both static and dynamic performance of the two devices. Microtabs, located at 95% chord on the lower surface and 90% chord on the upper surface, with a height of 1% chord, produce a change in the lift coefficient of 0.18, increasing lift when deployed on the lower surface and decreasing lift when deployed on the upper surface. Microjets with a momentum coefficient of 0.006 at the same locations produce a change in the lift coefficient of 0.19. The activation time for both devices is less than 0.3 s, which is rapid compared to typical gust rise times. The potential of active device to mitigate changes in loads was tested using simulated gusts. The gusts were produced in the wind tunnel by accelerating the test section air speed at rates of up to 7 ft/s 2. Open-loop control of microtabs was tested in two modes: simultaneous and sequential tab deployment. Activating all tabs along the model span simultaneously was found to produce a change in the loads that occurred more rapidly than a gust. Sequential tab deployment more closely matched the rates of change due to gusts and tab deployment. A closed-loop control system was developed for the microtabs using a simple feedback control based on lift measurements from a six-component balance. An alternative input to the control system that would be easier to implement on a turbine was also investigated: the lift force was estimated using the difference in surface pressure at 15% chord. Both control system approaches were found to decrease lift deviations by around 50% during rapid changes in the free stream air speed.

A geostatistical extreme-value framework for fast simulation of natural hazard events

PubMed Central

Stephenson, David B.

2016-01-01

We develop a statistical framework for simulating natural hazard events that combines extreme value theory and geostatistics. Robust generalized additive model forms represent generalized Pareto marginal distribution parameters while a Student’s t-process captures spatial dependence and gives a continuous-space framework for natural hazard event simulations. Efficiency of the simulation method allows many years of data (typically over 10 000) to be obtained at relatively little computational cost. This makes the model viable for forming the hazard module of a catastrophe model. We illustrate the framework by simulating maximum wind gusts for European windstorms, which are found to have realistic marginal and spatial properties, and validate well against wind gust measurements. PMID:27279768

Load alleviation maneuvers for a launch vehicle

NASA Technical Reports Server (NTRS)

Seywald, Hans; Bless, Robert

1993-01-01

This paper addresses the design of a forward-looking autopilot that is capable of employing a priori knowledge of wind gusts ahead of the flight path to reduce the bending loads experienced by a launch vehicle. The analysis presented in the present paper is only preliminary, employing a very simple vehicle dynamical model and restricting itself to wind gusts of the form of isolated spikes. The main result of the present study is that LQR based feedback laws are inappropriate to handle spike-type wind perturbations with large amplitude and narrow base. The best performance is achieved with an interior-point penalty optimal control formulation which can be well approximated by a simple feedback control law. Reduction of the maximum bending loads by nearly 50 percent is demonstrated.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms August 21, 1946 to August 22, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1946-01-01

Tables I and II of this report summarize the gust and draft velocity data for thunderstorm flights 25 and 26 of August 21, 1946 and August 22, 1946, respectively. These dta were evaluated from records of NACA instruments installed in P-61C airplanes and are of the type presented in reference 1 for previous flights. Table III summarizes the readings of a milliammeter which was used in conjunction with other equipment to indicate ambient air temperature during thunderstorm surveys. These data were read from motion-picture records of the instrument and include all cases in which variations in the instrument indications were noted during the present flights.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes Within Thunderstorms August 14, 1946 to August 15, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

Tables I and II of the present paper summarize the gust and draft velocity data for thunderstorm-flights 21 and 22 of August 14, 1946 and August 15, 1946, respectively. These data were evaluated from records of NACA airspeed-altitude and acceleration recorders installed in P-61C airplanes and are of the type presented for previous flights. Table III summarizes the readings of a milliammeter which was used in conjunction with other equipment to indicate ambient-air temperature during thunderstorm surveys. These data were read from photo-observer records and include all cases in which variations of the instrument indications were noted for the present flights.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms. IV - July 19, 1946 to July 20, 1946 at Orlando, Florida. Part 4; July 19, 1946 to July 20, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1946-01-01

Summaries of the gust and draft velocities evaluated from acceleration and airspeed-altitude records taken by NACA instruments installed n P-61c airplanes participating in thunderstorm flights 12 and 13 of July 19, 1946, and July 20, 1946, respectively, are presented in tables I and II herein. These data are of the type presented in reference 1 for previous flights. Inspection of the motion picture records of the pilots' instrument panels for the present flights indicated that the milliameter connected to equipment for measuring ambient air temperature read zero throughout all traverses.

Evaluation of Gust and Draft Velocities from Flights of P-61C Airplanes within Thunderstorms: September 5, 1946 to September 10, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1947-01-01

Tables I and II of this report summarize the gust and draft velocity data for thunderstorm flights 31, 32, and 33 of September 5, 1946, September 6, 1946, and September 10, 1946, respectively. These data were evaluated from records of NACA instruments installed in P-61C airplanes and are of the type presented for previous flights. Table III summarizes the readings of a milliammeter which was used in conjunction with other equipment to indicate ambient air temperature during thunderstorm surveys. These data were read from motion-picture records of the instrument and include all cases in which variations in the instrument indications were noted for the present flights.

Aeroservoelasticity

NASA Technical Reports Server (NTRS)

Noll, Thomas E.

1990-01-01

The paper describes recent accomplishments and current research projects along four main thrusts in aeroservoelasticity at NASA Langley. One activity focuses on enhancing the modeling and analysis procedures to accurately predict aeroservoelastic interactions. Improvements to the minimum-state method of approximating unsteady aerodynamics are shown to provide precise low-order models for design and simulation tasks. Recent extensions in aerodynamic correction-factor methodology are also described. With respect to analysis procedures, the paper reviews novel enhancements to matched filter theory and random process theory for predicting the critical gust profile and the associated time-correlated gust loads for structural design considerations. Two research projects leading towards improved design capability are also summarized: (1) an integrated structure/control design capability and (2) procedures for obtaining low-order robust digital control laws for aeroelastic applications.

Major Nor'easter Set to Impact Northeast U.S.

NASA Image and Video Library

2015-01-26

This image was taken by the Suomi NPP satellite's VIIRS instrument at 1825Z on January 26, 2015. A low pressure system currently forming off the mid-Atlantic coast will rapidly strengthen into a major nor'easter today and affect parts of the Northeast U.S. through early Wednesday. This system will be responsible for heavy to intense snowfall and strong winds, with blizzard conditions expected from eastern New Jersey to eastern Massachusetts where Blizzard Warnings are in effect. Accumulations will likely exceed one foot from eastern New Jersey through eastern Maine by late Tuesday. The heaviest snow accumulations, perhaps exceeding two feet, are forecast across portions of Connecticut, Rhode Island and Massachusetts, including the Boston area. Currently, New York City is forecast to receive 18-24 inches of snow, and Boston is forecast to receive 24-36 inches of snow. Wind gusts of 45 to 60 mph will be common from eastern New Jersey to eastern Massachusetts, leading to widespread blizzard conditions. Wind gusts up to 70 mph are possible in far eastern Massachusetts, including Cape Cod and Nantucket. Credit: NASA/NOAA/NPP/VIIRS Via: NASA/NOAA via NOAA Environmental Visualization Laboratory NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

Aeroservoelastic Wind-Tunnel Tests of a Free-Flying, Joined-Wing SensorCraft Model for Gust Load Alleviation

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Castelluccio, Mark A.; Coulson, David A.; Heeg, Jennifer

2011-01-01

A team comprised of the Air Force Research Laboratory (AFRL), Boeing, and the NASA Langley Research Center conducted three aeroservoelastic wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the first of these three tests, a full-span, aeroelastically scaled, wind-tunnel model of a joined-wing SensorCraft vehicle was mounted to a force balance to acquire a basic aerodynamic data set. In the second and third tests, the same wind-tunnel model was mated to a new, two-degree-of-freedom, beam mount. This mount allowed the full-span model to translate vertically and pitch. Trimmed flight at -10% static margin and gust load alleviation were successfully demonstrated. The rigid body degrees of freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort. The balance and free ying wind-tunnel tests will be summarized. The design of the trim and gust load alleviation control laws along with the associated results will also be discussed.

Spanwise measurements of vertical components of atmospheric turbulence

NASA Technical Reports Server (NTRS)

Sleeper, Robert K.

1990-01-01

Correlation and spectrum magnitude estimates are computed for vertical gust velocity measurements at the nose and wing tips of a NASA B-57B aircraft for six level flight, low speed and low altitude runs and are compared with those of the von Karman atmospheric turbulence model extended for spanwise relationships. The distance between the wing tips was 62.6 ft. Airspeeds ranged from about 330 to 400 ft/sec, heights above the ground ranged from near ground level to about 5250 ft. and gust velocity standard deviations ranged from 4.10 to 8.86 ft/sec. Integral scale lengths, determined by matching measured autocorrelation estimates with those of the model, ranged from 410 to 2050 ft. Digital signals derived from piezoelectric sensors provided continuous pressure and airspeed measurements. Some directional acceleration sensitivity of the sensors was eliminated by sensor orientation, and their performance was spectrally verified for the higher frequencies with supplemental onboard piezoresistive sensors. The model appeared to satisfactorily predict the trends of the measured cross-correlations and cross-spectrum magnitudes, particularly between the nose and wing tips. However, the measured magnitude estimates of the cross-spectra between the wing tips exceeded the predicted levels at the higher frequencies. Causes for the additional power across the wing tips were investigated. Vertical gust velocity components evaluated along and lateral to the flight path implied that the frozen-turbulence-field assumption is a suitable approximation.

Benchmark Problems Used to Assess Computational Aeroacoustics Codes

NASA Technical Reports Server (NTRS)

Dahl, Milo D.; Envia, Edmane

2005-01-01

The field of computational aeroacoustics (CAA) encompasses numerical techniques for calculating all aspects of sound generation and propagation in air directly from fundamental governing equations. Aeroacoustic problems typically involve flow-generated noise, with and without the presence of a solid surface, and the propagation of the sound to a receiver far away from the noise source. It is a challenge to obtain accurate numerical solutions to these problems. The NASA Glenn Research Center has been at the forefront in developing and promoting the development of CAA techniques and methodologies for computing the noise generated by aircraft propulsion systems. To assess the technological advancement of CAA, Glenn, in cooperation with the Ohio Aerospace Institute and the AeroAcoustics Research Consortium, organized and hosted the Fourth CAA Workshop on Benchmark Problems. Participants from industry and academia from both the United States and abroad joined to present and discuss solutions to benchmark problems. These demonstrated technical progress ranging from the basic challenges to accurate CAA calculations to the solution of CAA problems of increasing complexity and difficulty. The results are documented in the proceedings of the workshop. Problems were solved in five categories. In three of the five categories, exact solutions were available for comparison with CAA results. A fourth category of problems representing sound generation from either a single airfoil or a blade row interacting with a gust (i.e., problems relevant to fan noise) had approximate analytical or completely numerical solutions. The fifth category of problems involved sound generation in a viscous flow. In this case, the CAA results were compared with experimental data.

Control law synthesis and optimization software for large order aeroservoelastic systems

NASA Technical Reports Server (NTRS)

Mukhopadhyay, V.; Pototzky, A.; Noll, Thomas

1989-01-01

A flexible aircraft or space structure with active control is typically modeled by a large-order state space system of equations in order to accurately represent the rigid and flexible body modes, unsteady aerodynamic forces, actuator dynamics and gust spectra. The control law of this multi-input/multi-output (MIMO) system is expected to satisfy multiple design requirements on the dynamic loads, responses, actuator deflection and rate limitations, as well as maintain certain stability margins, yet should be simple enough to be implemented on an onboard digital microprocessor. A software package for performing an analog or digital control law synthesis for such a system, using optimal control theory and constrained optimization techniques is described.

Feasibility study for a microwave-powered ozone sniffer aircraft. B.S. Thesis

NASA Technical Reports Server (NTRS)

Botros, David F.; Cody, Charlotte K.; Forden, Noah P.; Helsing, Martin A.; Jutras, Thomas H.; Kim, Dohoon; Labarre, Christopher; Odin, Ethan M.; Sandler, Scott B.

1990-01-01

The preliminary design of a high-altitude, remotely-piloted, atmospheric-sampling aircraft powered by microwave energy beamed from ground-based antenna was completed. The vehicle has a gross weight of 6720 pounds and is sized to carry a 1000 pound payload at an altitude of 100,000 feet. The underside of the wing serves as the surface of a rectenna designed to receive microwave energy at a power density of 700 watts per square meter and the wing has a planform area of 3634 square feet to absorb the required power at an optimum Mach number M = 0.44. The aircraft utilizes a horizontal tail and a canard for longitudinal control and to enhance the structural rigidity of the twin fuselage configuration. The wing structure is designed to withstand a gust-induced load factor n = 3 at cruise altitude but the low-wing loading of the aircraft makes it very sensitive to gusts at low altitudes, which may induce load factors in excess of 20. A structural load alleviation system is therefore proposed to limit actual loads to the designed structural limit. Losses will require transmitted power on the order of megawatts to be radiated to the aircraft from the ground station, presenting environmental problems. Since the transmitting antenna would have a diameter of several hundred feet, it would not be readily transportable, so we propose that a single antenna be constructed at a site from which the aircraft is flown. The aircraft would be towed aloft to an initial altitude at which the microwave power would be utilized. The aircraft would climb to cruise altitude in a spiral flight path and orbit the transmitter in a gentle turn.

FIRE_AX_UKMO_C130

Atmospheric Science Data Center

2015-11-25

... FSSP Gust Probe Hot-Wire Hygrometer Platinum Resistance PMS 2D-C Probe PRT-4 Pyranometer Pyrgeometer ... Parameters:  Barometric Altitude Cloud Top Temperature Deiced Temperature Dew/Frost Point Temperature Droplet ...

Preliminary study of inphase gusts and moment force wind loads over the first 150 meters at KSC, Florida

NASA Technical Reports Server (NTRS)

Kaufman, J. W.

1985-01-01

A mathematical/statistical analysis of inphase gusts and wind velocity moment forces over the first 150 m at the Kennedy Space Center (KSC) is presented. The wind velocity profile data were acquired at the KSC 150 m ground wind tower. The results show that planetary boundary layer (PBL) winds can sustain near peak speeds for periods up to 60 sec and longer. This is proven from calculating the autocorrelation functions of moment forces for several 10 min cases of wind profile data. The results show that lower atmospheric planetary boundary layer winds have periodic variations for long periods of time. This flow characteristic is valuable as aerospace vehicle engineering and design criteria where wind loading must be determined.

A discrete gust model for use in the design of wind energy conversion systems

NASA Technical Reports Server (NTRS)

Frost, W.; Turner, R. E.

1982-01-01

A discrete gust model has been designed which includes an expression for the number of times per unit time thy wind exceeds a specific value. This expression, based on Rice's (1944, 1945) number-of-crossings model, assumes that the yearly mean wind speed is averaged over a period of 10 minutes to 1 (one) hour. Vertical and lateral coherence functions are the basis for a mathematical filter which isolates atmospheric disturbances of a characteristic size (e. g., those which would completely engulf a rotor). Predictions are calculated usising the given definition of cut-off frequency, then they are compared with actual data, showing that the model is reliable. The expression is provided in a format such that it may be used for engineering design calculations.

Load alleviation maneuvers for a launch vehicle

NASA Technical Reports Server (NTRS)

Seywald, Hans; Bless, Robert R.

1993-01-01

This paper addresses the design of a forward-looking autopilot that is capable of employing a priori knowledge of wind gusts ahead of the flight path to reduce the bending loads experienced by a launch vehicle. The analysis presented in the present paper is only preliminary, employing a very simple vehicle dynamical model and restricting itself to wind gusts of the form of isolated spikes. The main result of the present study is that linear quadratic regulator (LQR) based feedback laws are inappropriate to handle spike-type wind perturbations with large amplitude and narrow base. The best performance is achieved with an interior-point penalty optimal control formulation which can be well approximated by a simple feedback control law. Reduction of the maximum bending loads by nearly 50% is demonstrated.

Flight through thunderstorm outflows. [aircraft landing

NASA Technical Reports Server (NTRS)

Frost, W.; Crosby, B.; Camp, D. W.

1978-01-01

Computer simulation of aircraft landing through thunderstorm gust fronts is carried out. The two-dimensional, nonlinear equations or aircraft motion containing all wind shear terms are solved numerically. The gust front spatial wind field inputs are provided in the form of tabulated experimental data which are coupled with a computer table lookup routine to provide the required wind components and shear at any given position within an approximate 500 m by 1 km vertical plane. The aircraft is considered to enter the wind field at a specified position under trimmed conditions. Both fixed control and automatic control landings are simulated. Flight paths, as well as control inputs necessary to maintain specified trajectories, are presented and discussed for aircraft having characteristics of a DC-8, B-747, augmentor-wing STOL, and a DHC-6.

Flight through thunderstorm outflows

NASA Technical Reports Server (NTRS)

Frost, W.; Crosby, B.; Camp, D. W.

1979-01-01

Computer simulation of aircraft landing through thunderstorm gust fronts is carried out. The 3 degree-of-freedom, nonlinear equations of aircraft motion for the longitudinal variables containing all two-dimensional wind shear terms are solved numerically. The gust front spatial wind field inputs are provided in the form of tabulated experimental data which are coupled with a computer table lookup routine to provide the required wind components and shear at any given position within an approximate 500 m x 1 km vertical plane. The aircraft is considered to enter the wind field at a specified position under trimmed conditions. Both fixed control and automatic control landings are simulated. Flight paths, as well as control inputs necessary to maintain specified trajectories, are presented and discussed for aircraft having characteristics of a DC-8, B-747, and a DHC-6.

Climatic Conditions at Air Force Bases in Australia,

DTIC Science & Technology

1980-10-01

U"- C 0 - 0 4 4.M57 c 04. %OOOli~ 0C On mm 14 - 4P , cC)r )Go - 4-) 0 to to r. C)C r44 C V 0 ca.. x . . 04 1 -4 r-G 0o .4 4= 1. -40 -4 ) 4 04 Ju~0 C: 04...8217 0 C) 4.-4S- 0) to 0) N 9 0 4-4 4 4 1-4 -4 .- 4 4 -4 4 0 .4 W ) $4 .f in0A . T - :T -’ s- 4P .-4 C.) cn c 4 C- - 00 m 0 F-44 m)0J- ~ )N U) " ) enp co o...cyclones causes problems in predictfng extreme gust speeds for coastal stations north of latitude 30*S as was discussed under Extreme Rainfall. As was

14 CFR 29.395 - Control system.

Code of Federal Regulations, 2013 CFR

2013-01-01

... consideration of fatigue, jamming, ground gusts, control inertia, and friction loads. In the absence of a... inertia, or friction, the system must withstand the limit pilot forces specified in § 29.397, without...

14 CFR 25.445 - Auxiliary aerodynamic surfaces.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads..., and gusts as specified in § 25.341(a) acting at any orientation at right angles to the flight path. (b...

14 CFR 25.445 - Auxiliary aerodynamic surfaces.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Control Surface and System Loads..., and gusts as specified in § 25.341(a) acting at any orientation at right angles to the flight path. (b...

14 CFR 23.343 - Design fuel loads.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Gust velocities equal to 85 percent of the values prescribed in § 23.333(c). (2) The fatigue evaluation of the structure must account for any increase in operating stresses resulting from the design...

SORD Special Operations and Research Division)

Science.gov Websites

) Climate Summaries Lightning Precipitation Wind Chill Chart Wind Roses Sodar Sodar Data Wind Plot Vertical ) Relative Humidity (%) Max Wind Gust (mph) Pressure (mb) Precipitation (in) Solar Radiation (W/m^2) Battery

Analytical study of a free-wing/free-trimmer concept. [for gust alleviation and high lift

NASA Technical Reports Server (NTRS)

Porter, R. F.; Hall, D. W.; Brown, J. H., Jr.; Gregorek, G. M.

1978-01-01

The free-wing/free-trimmer is a NASA-Conceived extension of the free-wing concept intended to permit the use of high-lift flaps. Wing pitching moments are balanced by a smaller, external surface attached by a boom or equivalent structure. The external trimmer is, itself, a miniature free wing, and pitch control of the wing-trimmer assembly is effected through a trailing-edge control tab on the trimmer surface. The longitudinal behavior of representative small free-wing/free-trimmer aircraft was analyzed. Aft-mounted trimmer surfaces are found to be superior to forward trimmers, although the permissible trimmer moment arm is limited, in both cases, by adverse dynamic effects. Aft-trimmer configurations provide excellent gust alleviation and meet fundamental stick-fixed stability criteria while exceeding the lift capabilities of pure free-wing configurations.

Evaluation of Gust and Draft Velocities from Flights of P-61c Airplanes within Thunderstorms. III - July 12, 1946 to July 18, 1946 at Orlando, Florida. Part 3; July 12, 1946 to July 18, 1946 at Orlando, Florida

NASA Technical Reports Server (NTRS)

Tolefson, H. B.

1946-01-01

The gust and draft velocities evaluated from acceleration and airspeed-altitude records taken by NACA instruments installed in P-61c airplanes participating in thunderstorm flights 9, 10, and 11 of July 12, 1946, July 17, 1946, and July 18, 1946, respectively, are presented in references 1 and 2 for previous flights. In accordance with a recent discussion with a member of the U.S. Weather Bureau staff, motion-picture records of the pilots' instrument panels for the present flights were inspected to note variations in the readings of a milliammeter used in conjunction with other equipment to indicate ambient air temperature. The inspection indicated that the instrument read zero throughout all traverses.

Explosive cyclogenesis of extra-tropical cyclone Klaus and its effects in Catalonia. A case study of hurricane force gusts.

NASA Astrophysics Data System (ADS)

Calvo, J.; López, J. A.; Martín, F.; Morales, G.; Pascual, R.

2009-09-01

On 23th and 24th of January 2009, the extra-tropical cyclone Klaus crossed the north of Spain and the south of France producing several deaths and generalized damages. The cyclone of Atlantic origin underwent an explosive deepening of more than 1 hPa per hour at the surface level. Catalonia region was affected by gale-force winds and hurricane gusts. The Atlantic depression underwent a process called explosive cyclogenesis (when a surface cyclone deepens at a rate higher than 1 hPa/hr over 24 hours, approximately) in front of the Spanish Atlantic coasts. In this study we focus on its impact in the Catalonia areas where both synoptic and local effects were important. Also we evaluate the performance of the numerical weather prediction model outputs against observed data.

Design for active and passive flutter suppression and gust alleviation. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Karpel, M.

1981-01-01

Analytical design techniques for active and passive control of aeroelastic systems are based on a rational approximation of the unsteady aerodynamic loads in the entire Laplace domain, which yields matrix equations of motion with constant coefficients. Some existing schemes are reviewed, the matrix Pade approximant is modified, and a technique which yields a minimal number of augmented states for a desired accuracy is presented. The state-space aeroelastic model is used to design an active control system for simultaneous flutter suppression and gust alleviation. The design target is for a continuous controller which transfers some measurements taken on the vehicle to a control command applied to a control surface. Structural modifications are formulated in a way which enables the treatment of passive flutter suppression system with the same procedures by which active control systems are designed.

Gaussian and Lognormal Models of Hurricane Gust Factors

NASA Technical Reports Server (NTRS)

Merceret, Frank

2009-01-01

A document describes a tool that predicts the likelihood of land-falling tropical storms and hurricanes exceeding specified peak speeds, given the mean wind speed at various heights of up to 500 feet (150 meters) above ground level. Empirical models to calculate mean and standard deviation of the gust factor as a function of height and mean wind speed were developed in Excel based on data from previous hurricanes. Separate models were developed for Gaussian and offset lognormal distributions for the gust factor. Rather than forecasting a single, specific peak wind speed, this tool provides a probability of exceeding a specified value. This probability is provided as a function of height, allowing it to be applied at a height appropriate for tall structures. The user inputs the mean wind speed, height, and operational threshold. The tool produces the probability from each model that the given threshold will be exceeded. This application does have its limits. They were tested only in tropical storm conditions associated with the periphery of hurricanes. Winds of similar speed produced by non-tropical system may have different turbulence dynamics and stability, which may change those winds statistical characteristics. These models were developed along the Central Florida seacoast, and their results may not accurately extrapolate to inland areas, or even to coastal sites that are different from those used to build the models. Although this tool cannot be generalized for use in different environments, its methodology could be applied to those locations to develop a similar tool tuned to local conditions.

Application of the aerodynamic energy concept to flutter suppression and gust alleviation by use of active controls

NASA Technical Reports Server (NTRS)

Nissim, E.; Caspi, A.; Lottati, I.

1976-01-01

The effects of active controls on flutter suppression and gust alleviation of the Arava twin turboprop STOL transport and the Westwind twinjet business transport are investigated. The active control surfaces are introduced in pairs which include, in any chosen wing strip, a 20-percent chord leading-edge control and a 20-percent chord trailing-edge control. Each control surface is driven by a combined linear-rotational sensor system located on the activated strip. The control law is based on the concept of aerodynamic energy and utilizes previously optimized control law parameters based on two-dimensional aerodynamic theory. The best locations of the activated system along the span of the wing are determined for bending-moment alleviation, reduction in fuselage accelerations, and flutter suppression. The effectiveness of the activated system over a wide range of maximum control deflections is also determined. Two control laws are investigated. The first control law utilizes both rigid-body and elastic contributions of the motion. The second control law employs primarily the elastic contribution of the wing and leads to large increases in the activated control effectiveness as compared with the basic control law. The results indicate that flutter speed can be significantly increased (over 70 percent increase) and that the bending moment due to gust loading can be almost totally eliminated by a control system of about 10 to 20 percent span with reasonable control-surface rotations.

Gust alleviation of highly flexible UAVs with artificial hair sensors

NASA Astrophysics Data System (ADS)

Su, Weihua; Reich, Gregory W.

2015-04-01

Artificial hair sensors (AHS) have been recently developed in Air Force Research Laboratory (AFRL) using carbon nanotube (CNT). The deformation of CNT in air flow causes voltage and current changes in the circuit, which can be used to quantify the dynamic pressure and aerodynamic load along the wing surface. AFRL has done a lot of essential work in design, manufacturing, and measurement of AHSs. The work in this paper is to bridge the current AFRL's work on AHSs and their feasible applications in flight dynamics and control (e.g., the gust alleviation) of highly flexible aircraft. A highly flexible vehicle is modeled using a strain-based geometrically nonlinear beam formulation, coupled with finite-state inflow aerodynamics. A feedback control algorithm for the rejection of gust perturbations will be developed. A simplified Linear Quadratic Regulator (LQR) controller will be implemented based on the state-space representation of the linearized system. All AHS measurements will be used as the control input, i.e., wing sectional aerodynamic loads will be defined as the control output for designing the feedback gain. Once the controller is designed, closed-loop aeroelastic simulations will be performed to evaluate the performance of different controllers with the force feedback and be compared to traditional controller designs with the state feedback. From the study, the feasibility of AHSs in flight control will be assessed. The whole study will facilitate in building a fly-by-feel simulation environment for autonomous vehicles.

Does a ‘turbophoretic’ effect account for layer concentrations of insects migrating in the stable night-time atmosphere?

PubMed Central

Reynolds, A.M; Reynolds, D.R; Riley, J.R

2008-01-01

Large migrating insects, such as noctuid moths and acridoid grasshoppers, flying within the stable nocturnal boundary layer commonly become concentrated into horizontal layers. These layers frequently occur near the top of the surface temperature inversion where warm fast-moving airflows provide good conditions for downwind migration. On some occasions, a layer may coincide with a higher altitude temperature maximum such as a subsidence inversion, while on others, it may seem unrelated to any obvious feature in the vertical profile of meteorological variables. Insects within the layers are frequently orientated, either downwind or at an angle to the wind, but the mechanisms involved in both layer formation and common orientation have remained elusive. Here, we show through the results of numerical simulations that if insects are treated as neutrally buoyant particles, they tend to be advected by vertical gusts (through the ‘turbophoretic’ mechanism) into layers in the atmosphere where the turbulent kinetic energy has local minima. These locations typically coincide with local maxima in the wind speed and/or air temperature, and they may also provide cues for orientation. However, the degree of layering predicted by this model is very much weaker than that observed in the field. We have therefore hypothesized that insects behave in a way that amplifies the turbophoretic effect by initiating climbs or descents in response to vertical gusts. New simulations incorporating this behaviour demonstrated the formation of layers that closely mimic field observations, both in the degree of concentration in layers and the rate at which they form. PMID:18611845

Does a 'turbophoretic' effect account for layer concentrations of insects migrating in the stable night-time atmosphere?

PubMed

Reynolds, A M; Reynolds, D R; Riley, J R

2009-01-06

Large migrating insects, such as noctuid moths and acridoid grasshoppers, flying within the stable nocturnal boundary layer commonly become concentrated into horizontal layers. These layers frequently occur near the top of the surface temperature inversion where warm fast-moving airflows provide good conditions for downwind migration. On some occasions, a layer may coincide with a higher altitude temperature maximum such as a subsidence inversion, while on others, it may seem unrelated to any obvious feature in the vertical profile of meteorological variables. Insects within the layers are frequently orientated, either downwind or at an angle to the wind, but the mechanisms involved in both layer formation and common orientation have remained elusive. Here, we show through the results of numerical simulations that if insects are treated as neutrally buoyant particles, they tend to be advected by vertical gusts (through the 'turbophoretic' mechanism) into layers in the atmosphere where the turbulent kinetic energy has local minima. These locations typically coincide with local maxima in the wind speed and/or air temperature, and they may also provide cues for orientation. However, the degree of layering predicted by this model is very much weaker than that observed in the field. We have therefore hypothesized that insects behave in a way that amplifies the turbophoretic effect by initiating climbs or descents in response to vertical gusts. New simulations incorporating this behaviour demonstrated the formation of layers that closely mimic field observations, both in the degree of concentration in layers and the rate at which they form.

Design Challenges Encountered in a Propulsion-Controlled Aircraft Flight Test Program

NASA Technical Reports Server (NTRS)

Maine, Trindel; Burken, John; Burcham, Frank; Schaefer, Peter

1994-01-01

The NASA Dryden Flight Research Center conducted flight tests of a propulsion-controlled aircraft system on an F-15 airplane. This system was designed to explore the feasibility of providing safe emergency landing capability using only the engines to provide flight control in the event of a catastrophic loss of conventional flight controls. Control laws were designed to control the flightpath and bank angle using only commands to the throttles. Although the program was highly successful, this paper highlights some of the challenges associated with using engine thrust as a control effector. These challenges include slow engine response time, poorly modeled nonlinear engine dynamics, unmodeled inlet-airframe interactions, and difficulties with ground effect and gust rejection. Flight and simulation data illustrate these difficulties.

Modern control techniques in active flutter suppression using a control moment gyro

NASA Technical Reports Server (NTRS)

Buchek, P. M.

1974-01-01

Development of organized synthesis techniques, using concepts of modern control theory was studied for the design of active flutter suppression systems for two and three-dimensional lifting surfaces, utilizing a control moment gyro (CMG) to generate the required control torques. Incompressible flow theory is assumed, with the unsteady aerodynamic forces and moments for arbitrary airfoil motion obtained by using the convolution integral based on Wagner's indicial lift function. Linear optimal control theory is applied to find particular optimal sets of gain values which minimize a quadratic performance function. The closed loop system's response to impulsive gust disturbances and the resulting control power requirements are investigated, and the system eigenvalues necessary to minimize the maximum value of control power are determined.

Finite Element Aircraft Simulation of Turbulence

DOT National Transportation Integrated Search

1997-02-01

A Simulation of Rotor Blade Element Turbulence (SORBET) model has been : developed for realtime aircraft simulation that accommodates stochastic : turbulence and distributed discrete gusts as a function of the terrain. This : model is applicable to c...

Sensitivity Analysis of Expected Wind Extremes over the Northwestern Sahara and High Atlas Region.

NASA Astrophysics Data System (ADS)

Garcia-Bustamante, E.; González-Rouco, F. J.; Navarro, J.

2017-12-01

A robust statistical framework in the scientific literature allows for the estimation of probabilities of occurrence of severe wind speeds and wind gusts, but does not prevent however from large uncertainties associated with the particular numerical estimates. An analysis of such uncertainties is thus required. A large portion of this uncertainty arises from the fact that historical observations are inherently shorter that the timescales of interest for the analysis of return periods. Additional uncertainties stem from the different choices of probability distributions and other aspects related to methodological issues or physical processes involved. The present study is focused on historical observations over the Ouarzazate Valley (Morocco) and in a high-resolution regional simulation of the wind in the area of interest. The aim is to provide extreme wind speed and wind gust return values and confidence ranges based on a systematic sampling of the uncertainty space for return periods up to 120 years.

Investigation of aircraft landing in variable wind fields

NASA Technical Reports Server (NTRS)

Frost, W.; Reddy, K. R.

1978-01-01

A digital simulation study is reported of the effects of gusts and wind shear on the approach and landing of aircraft. The gusts and wind shear are primarily those associated with wind fields created by surface wind passing around bluff geometries characteristic of buildings. Also, flight through a simple model of a thunderstorm is investigated. A two-dimensional model of aircraft motion was represented by a set of nonlinear equations which accounted for both spatial and temporal variations of winds. The landings of aircraft with the characteristics of a DC-8 and a DHC-6 were digitally simulated under different wind conditions with fixed and automatic controls. The resulting deviations in touchdown points and the controls that are required to maintain the desired flight path are presented. The presence of large bluff objects, such as buildings in the flight path is shown to have considerable effect on aircraft landings.

Pulsed laser Doppler measurements of wind shear

NASA Technical Reports Server (NTRS)

Dimarzio, C.; Harris, C.; Bilbro, J. W.; Weaver, E. A.; Burnham, D. C.; Hallock, J. N.

1979-01-01

There is a need for a sensor at the airport that can remotely detect, identify, and track wind shears near the airport in order to assure aircraft safety. To determine the viability of a laser wind-shear system, the NASA pulsed coherent Doppler CO2 lidar (Jelalian et al., 1972) was installed in a semitrailer van with a rooftop-mounted hemispherical scanner and was used to monitor thunderstorm gust fronts. Wind shears associated with the gust fronts at the Kennedy Space Center (KSC) between 5 July and 4 August 1978 were measured and tracked. The most significant data collected at KSC are discussed. The wind shears were clearly visible in both real-time velocity vs. azimuth plots and in postprocessing displays of velocities vs. position. The results indicate that a lidar system cannot be used effectively when moderate precipitation exists between the sensor and the region of interest.

Role of surface heat fluxes underneath cold pools

PubMed Central

Garelli, Alix; Park, Seung‐Bu; Nie, Ji; Torri, Giuseppe; Kuang, Zhiming

2016-01-01

Abstract The role of surface heat fluxes underneath cold pools is investigated using cloud‐resolving simulations with either interactive or horizontally homogenous surface heat fluxes over an ocean and a simplified land surface. Over the ocean, there are limited changes in the distribution of the cold pool temperature, humidity, and gust front velocity, yet interactive heat fluxes induce more cold pools, which are smaller, and convection is then less organized. Correspondingly, the updraft mass flux and lateral entrainment are modified. Over the land surface, the heat fluxes underneath cold pools drastically impact the cold pool characteristics with more numerous and smaller pools, which are warmer and more humid and accompanied by smaller gust front velocities. The interactive fluxes also modify the updraft mass flux and reduce convective organization. These results emphasize the importance of interactive surface fluxes instead of prescribed flux boundary conditions, as well as the formulation of surface heat fluxes, when studying convection. PMID:27134320

Turbulence flight director analysis and preliminary simulation

NASA Technical Reports Server (NTRS)

Johnson, D. E.; Klein, R. E.

1974-01-01

A control column and trottle flight director display system is synthesized for use during flight through severe turbulence. The column system is designed to minimize airspeed excursions without overdriving attitude. The throttle system is designed to augment the airspeed regulation and provide an indication of the trim thrust required for any desired flight path angle. Together they form an energy management system to provide harmonious display indications of current aircraft motions and required corrective action, minimize gust upset tendencies, minimize unsafe aircraft excursions, and maintain satisfactory ride qualities. A preliminary fixed-base piloted simulation verified the analysis and provided a shakedown for a more sophisticated moving-base simulation to be accomplished next. This preliminary simulation utilized a flight scenario concept combining piloting tasks, random turbulence, and discrete gusts to create a high but realistic pilot workload conducive to pilot error and potential upset. The turbulence director (energy management) system significantly reduced pilot workload and minimized unsafe aircraft excursions.

Theoretical Calculation of the Power Spectra of the Rolling and Yawing Moments on a Wing in Random Turbulence

NASA Technical Reports Server (NTRS)

Eggleston, John M; Diederich, Franklin W

1957-01-01

The correlation functions and power spectra of the rolling and yawing moments on an airplane wing due to the three components of continuous random turbulence are calculated. The rolling moments to the longitudinal (horizontal) and normal (vertical) components depend on the spanwise distributions of instantaneous gust intensity, which are taken into account by using the inherent properties of symmetry of isotropic turbulence. The results consist of expressions for correlation functions or spectra of the rolling moment in terms of the point correlation functions of the two components of turbulence. Specific numerical calculations are made for a pair of correlation functions given by simple analytic expressions which fit available experimental data quite well. Calculations are made for four lift distributions. Comparison is made with the results of previous analyses which assumed random turbulence along the flight path and linear variations of gust velocity across the span.

Structural optimization procedure of a composite wind turbine blade for reducing both material cost and blade weight

NASA Astrophysics Data System (ADS)

Hu, Weifei; Park, Dohyun; Choi, DongHoon

2013-12-01

A composite blade structure for a 2 MW horizontal axis wind turbine is optimally designed. Design requirements are simultaneously minimizing material cost and blade weight while satisfying the constraints on stress ratio, tip deflection, fatigue life and laminate layup requirements. The stress ratio and tip deflection under extreme gust loads and the fatigue life under a stochastic normal wind load are evaluated. A blade element wind load model is proposed to explain the wind pressure difference due to blade height change during rotor rotation. For fatigue life evaluation, the stress result of an implicit nonlinear dynamic analysis under a time-varying fluctuating wind is converted to the histograms of mean and amplitude of maximum stress ratio using the rainflow counting algorithm Miner's rule is employed to predict the fatigue life. After integrating and automating the whole analysis procedure an evolutionary algorithm is used to solve the discrete optimization problem.

Adaptive Highly Flexible Multifunctional Wings for Active and Passive Control and Energy Harvesting with Piezoelectric Materials

NASA Astrophysics Data System (ADS)

Tsushima, Natsuki

The purpose of this dissertation is to develop an analytical framework to analyze highly flexible multifunctional wings with integral active and passive control and energy harvesting using piezoelectric transduction. Such multifunctional wings can be designed to enhance aircraft flight performance, especially to support long-endurance flights and to be adaptive to various flight conditions. This work also demonstrates the feasibility of the concept of piezoelectric multifunctional wings for the concurrent active control and energy harvesting to improve the aeroelastic performance of high-altitude long-endurance unmanned air vehicles. Functions of flutter suppression, gust alleviation, energy generation, and energy storage are realized for the performance improvement. The multifunctional wings utilize active and passive piezoelectric effects for the efficient adaptive control and energy harvesting. An energy storage with thin-film lithium-ion battery cells is designed for harvested energy accumulation. Piezoelectric effects are included in a strain-based geometrically nonlinear beam formulation for the numerical studies. The resulting structural dynamic equations are coupled with a finite-state unsteady aerodynamic formulation, allowing for piezoelectric energy harvesting and active actuation with the nonlinear aeroelastic system. This development helps to provide an integral electro-aeroelastic solution of concurrent active piezoelectric control and energy harvesting for wing vibrations, with the consideration of the geometrical nonlinear effects of slender multifunctional wings. A multifunctional structure for active actuation is designed by introducing anisotropic piezoelectric laminates. Linear quadratic regulator and linear quadratic Gaussian controllers are implemented for the active control of wing vibrations including post-flutter limit-cycle oscillations and gust perturbation. An adaptive control algorithm for gust perturbation is then developed. In this research, the active piezoelectric actuation is applied as the primary approach for flutter suppression, with energy harvesting, as a secondary passive approach, concurrently working to provide an additional damping effect on the wing vibration. The multifunctional wing also generates extra energy from residual wing vibration. This research presents a comprehensive approach for an effective flutter suppression and gust alleviation of highly flexible piezoelectric wings, while allowing to harvest the residual vibration energy. Numerical results with the multifunctional wing concept show the potential to improve the aircraft performance from both aeroelastic stability and energy consumption aspects.

Large-Eddy Simulation of the Impact of Great Garuda Project on Wind and Thermal Environment over Built-Up Area in Jakarta

NASA Astrophysics Data System (ADS)

Yucel, M.; Sueishi, T.; Inagaki, A.; Kanda, M.

2017-12-01

`Great Garuda' project is an eagle-shaped offshore structure with 17 artificial islands. This project has been designed for the coastal protection and land reclamation of Jakarta due to catastrophic flooding in the city. It offers an urban generation for 300.000 inhabitants and 600.000 workers in addition to its water safety goal. A broad coalition of Indonesian scientists has criticized the project for being negative impacts on the surrounding environment. Despite the vast research by Indonesian scientist on maritime environment, studies on wind and thermal environment over built-up area are still lacking. However, the construction of the various islands off the coast may result changes in wind patterns and thermal environment due to the alteration of the coastline and urbanization in the Jakarta Bay. Therefore, it is important to understand the airflow within the urban canopy in case of unpredictable gust events. These gust events may occur through the closely-packed high-rise buildings and pedestrians may be harmed from such gusts. Accordingly, we used numerical simulations to investigate the impact of the sea wall and the artificial islands over built-up area and, the intensity of wind gusts at the pedestrian level. Considering the fact that the size of turbulence organized structure sufficiently large computational domain is required. Therefore, a 19.2km×4.8km×1.0 km simulation domain with 2-m resolution in all directions was created to explicitly resolve the detailed shapes of buildings and the flow at the pedestrian level. This complex computation was accomplished by implementing a large-eddy simulation (LES) model. Two case studies were conducted considering the effect of realistic surface roughness and upward heat flux. Case_1 was conducted based on the current built environment and Case_2 for investigating the effect of the project on the chosen coastal region of the city. Fig.1 illustrates the schematic of the large-eddy simulation domains of two cases with and without Great Garuda Sea Wall and 17 artificial islands. 3D model of Great Garuda is shown in Fig.2. In addition to the cases mentioned above, the simulation will be generated assigning more realistic heat flux outputs from energy balance model and, inflow boundary conditions coupling with mesoscale model (Weather Research and Forecast model).

Uncertainty management for aerial vehicles: Coordination, deconfliction, and disturbance rejection

NASA Astrophysics Data System (ADS)

Panyakeow, Prachya

The presented dissertation aims to develop control algorithms that deal with three types of uncertainties managements. First, we examine the situation when unmanned aerial vehicles (UAVs) fly through uncertain environments that contain both stationary and moving obstacles. Moreover, a guarantee of collision avoidance is necessary when UAVs operate in close proximity of each other. Second, we look at the communication uncertainty among the network of cooperative UAVs and the efforts to establish and maintain the connectivity throughout their entire missions. Third, we explore the scenario when the aircraft flies through wind gust. The introduction of an appropriate control scheme to actively alleviate the gust loads can result into weight reduction and consequently lower the fuel cost. In the first part of this dissertation, we develop a deconfliction algorithm that guarantees collision avoidance between a pair of constant speed unicycle-type UAVs as well as convergence to the desired destination for each UAV in presence of static obstacles. We use a combination of navigation and swirling functions to direct the unicycle vehicles along the planned trajectories while avoiding inter-vehicle collisions. The main feature of our contribution is proposing means of designing a deconfliction algorithm for unicycle vehicles that more closely capture the dynamics of constant speed UAVs as opposed to double integrator models. Specifically, we consider the issue of UAV turn-rate constraints and proceed to explore the selection of key algorithmic parameters in order to minimize undesirable trajectories and overshoots induced by the avoidance algorithm. The avoidance and convergence analysis of the proposed algorithm is then performed for two cooperative UAVs and simulation results are provided to support the viability of the proposed framework for more general mission scenarios. For the uncertainty of the UAV network, we provides two approaches to establish connectivity among a collection of UAVs that are initially scattered in space. The goal is to find shortest trajectories that bring the UAVs to a connected formation where they are in the range of detection of one another and headed in the same direction to maintain the connectivity. Pontryagin Minimum Principle (PMP) is utilized to determine the control law and path synthesis for the UAVs under the turn-rate constraints. We introduce an algorithm to search for the optimal solution when the final network topology is specified; followed by a nonlinear programming method in which the final configuration is emerged from the optimization routine under the constraints that the final topology is connected. Each method has its own advantages based on the size of corporative networks. For the uncertainty due to gust turbulence, we choose a model predictive control (MPC) technique to address gust load alleviation (GLA) for a flexible aircraft. MPC is a discrete method based on repeated online optimization that allows direct consideration of control actuator constraints into the feedback computation. Gust alleviation systems are dependent on how the structural flexibility of the aircraft affects its dynamics. Hence, we develop a six-degree-of-freedom flexible aircraft model that can integrate rigid body dynamic with structural deflection. The structural stick-and-beam model is utilized for the calculation of aeroelastic mode shapes and airframe loads. Another important feature of MPC for GLA design is the ability to include the preview of gust information ahead of the aircraft nose into the prediction process. This helps raising the prediction accuracy and consequently improves the load alleviation performance. Finally, the aircraft is modified by the addition of the flap-array, a composition of small trailing edge flaps throughout the entire span of the wings. These flaps are used in conjunction with the distributed spoilers. With the availability of the control surfaces closer to the wing root, the MPC with flap-array can reduce the wing bending moment from different mode shapes and achieve better load alleviation performance than the original aircraft.

Towards a parameterization of convective wind gusts in Sahel

NASA Astrophysics Data System (ADS)

Largeron, Yann; Guichard, Françoise; Bouniol, Dominique; Couvreux, Fleur; Birch, Cathryn; Beucher, Florent

2014-05-01

West Africa is responsible for between 25 and 50 % of the global emissions of mineral dust (cf [Engelstaedter et al., 2006]) and these dust emissions have a huge impact on climate (cf [Carslaw et al., 2010]) and soil erosion. Numerous studies have focused on the quantification of the dust emission fluxes from knowledges of the soil surface characteristics, leading to the formulation of a threshold wind friction velocity (cf [Marticorena and Bergametti, 1995]) above which the dust can be uplifted. That flux varies with the cube of the surface wind speed above the threshold and is therefore particularly sensitive to the way the wind speed is modeled (cf [Menut, 2008]). Moreover, in the Sahelian belt, about half of the dust uplift happens during isolated events which generate violent cold pool outflows from moist deep convection, and associated high surface wind speeds. Therefore, the representation of convectively generated winds appears critical (cf [Marsham et al., 2011], [Knippertz and Todd, 2012]). The present study is motivated by these issues, and is carried out within the CAVIARS French Research National Agency (ANR) project. First, we examine the ERA interim reanalysis of the ECMWF, frequently used as an input wind field for off-line dust emission models (cf [Pierre et al., 2012]). The comparison with high-frequency local measurements shows that, not unexpectedly, the increase of the surface wind speed from deep convection is not represented in large-scale reanalysis. Therefore, following [Redelsperger et al., 2000], we propose a statistical approach to introduce a formulation of the surface wind gusts during deep convection, based on the analysis of convection-permitting high resolution simulations made with the UKMO atmospheric model (CASCADE project), the AROME operational model from Meteo-France, and the MesoNH Large Eddy Simulations model. High-frequency observations are also used to complement the analysis. However, unlike [Redelsperger et al., 2000] who focused on the wet tropical Pacific region, and linked wind gusts to convective precipitation rates alone, here, we also analyse the subgrid wind distribution during convective events, and quantify the statistical moments (variance, skewness and kurtosis) in terms of mean wind speed and convective indexes such as DCAPE. Next step of the work will be to formulate a parameterization of the cold pool convective gust from those probability density functions and analytical formulaes obtained from basic energy budget models. References : [Carslaw et al., 2010] A review of natural aerosol interactions and feedbacks within the earth system. Atmospheric Chemistry and Physics, 10(4):1701{1737. [Engelstaedter et al., 2006] North african dust emissions and transport. Earth-Science Reviews, 79(1):73{100. [Knippertz and Todd, 2012] Mineral dust aerosols over the sahara: Meteorological controls on emission and transport and implications for modeling. Reviews of Geophysics, 50(1). [Marsham et al., 2011] The importance of the representation of deep convection for modeled dust-generating winds over west africa during summer.Geophysical Research Letters, 38(16). [Marticorena and Bergametti, 1995] Modeling the atmospheric dust cycle: 1. design of a soil-derived dust emission scheme. Journal of Geophysical Research, 100(D8):16415{16. [Menut, 2008] Sensitivity of hourly saharan dust emissions to ncep and ecmwf modeled wind speed. Journal of Geophysical Research: Atmospheres (1984{2012), 113(D16). [Pierre et al., 2012] Impact of vegetation and soil moisture seasonal dynamics on dust emissions over the sahel. Journal of Geophysical Research: Atmospheres (1984{2012), 117(D6). [Redelsperger et al., 2000] A parameterization of mesoscale enhancement of surface fluxes for large-scale models. Journal of climate, 13(2):402{421.

Digital robust active control law synthesis for large order systems using constrained optimization

NASA Technical Reports Server (NTRS)

Mukhopadhyay, Vivek

1987-01-01

This paper presents a direct digital control law synthesis procedure for a large order, sampled data, linear feedback system using constrained optimization techniques to meet multiple design requirements. A linear quadratic Gaussian type cost function is minimized while satisfying a set of constraints on the design loads and responses. General expressions for gradients of the cost function and constraints, with respect to the digital control law design variables are derived analytically and computed by solving a set of discrete Liapunov equations. The designer can choose the structure of the control law and the design variables, hence a stable classical control law as well as an estimator-based full or reduced order control law can be used as an initial starting point. Selected design responses can be treated as constraints instead of lumping them into the cost function. This feature can be used to modify a control law, to meet individual root mean square response limitations as well as minimum single value restrictions. Low order, robust digital control laws were synthesized for gust load alleviation of a flexible remotely piloted drone aircraft.

Targeted taste cell-specific overexpression of brain-derived neurotrophic factor in adult taste buds elevates phosphorylated TrkB protein levels in taste cells, increases taste bud size, and promotes gustatory innervation.

PubMed

Nosrat, Irina V; Margolskee, Robert F; Nosrat, Christopher A

2012-05-11

Brain-derived neurotrophic factor (BDNF) is the most potent neurotrophic factor in the peripheral taste system during embryonic development. It is also expressed in adult taste buds. There is a lack of understanding of the role of BDNF in the adult taste system. To address this, we generated novel transgenic mice in which transgene expression was driven by an α-gustducin promoter coupling BDNF expression to the postnatal expression of gustducin in taste cells. Immunohistochemistry revealed significantly stronger BDNF labeling in taste cells of high BDNF-expressing mouse lines compared with controls. We show that taste buds in these mice are significantly larger and have a larger number of taste cells compared with controls. To examine whether innervation was affected in Gust-BDNF mice, we used antibodies to neural cell adhesion molecule (NCAM) and ATP receptor P2X3. The total density of general innervation and specifically the gustatory innervation was markedly increased in high BDNF-expressing mice compared with controls. TrkB and NCAM gene expression in laser capture microdissected taste epithelia were significantly up-regulated in these mice. Up-regulation of TrkB transcripts in taste buds and elevated taste cell-specific TrkB phosphorylation in response to increased BDNF levels indicate that BDNF controls the expression and activation of its high affinity receptor in taste cells. This demonstrates a direct taste cell function for BDNF. BDNF also orchestrates and maintains taste bud innervation. We propose that the Gust-BDNF transgenic mouse models can be employed to further dissect the specific roles of BDNF in the adult taste system.

Targeted Taste Cell-specific Overexpression of Brain-derived Neurotrophic Factor in Adult Taste Buds Elevates Phosphorylated TrkB Protein Levels in Taste Cells, Increases Taste Bud Size, and Promotes Gustatory Innervation*

PubMed Central

Nosrat, Irina V.; Margolskee, Robert F.; Nosrat, Christopher A.

2012-01-01

Brain-derived neurotrophic factor (BDNF) is the most potent neurotrophic factor in the peripheral taste system during embryonic development. It is also expressed in adult taste buds. There is a lack of understanding of the role of BDNF in the adult taste system. To address this, we generated novel transgenic mice in which transgene expression was driven by an α-gustducin promoter coupling BDNF expression to the postnatal expression of gustducin in taste cells. Immunohistochemistry revealed significantly stronger BDNF labeling in taste cells of high BDNF-expressing mouse lines compared with controls. We show that taste buds in these mice are significantly larger and have a larger number of taste cells compared with controls. To examine whether innervation was affected in Gust-BDNF mice, we used antibodies to neural cell adhesion molecule (NCAM) and ATP receptor P2X3. The total density of general innervation and specifically the gustatory innervation was markedly increased in high BDNF-expressing mice compared with controls. TrkB and NCAM gene expression in laser capture microdissected taste epithelia were significantly up-regulated in these mice. Up-regulation of TrkB transcripts in taste buds and elevated taste cell-specific TrkB phosphorylation in response to increased BDNF levels indicate that BDNF controls the expression and activation of its high affinity receptor in taste cells. This demonstrates a direct taste cell function for BDNF. BDNF also orchestrates and maintains taste bud innervation. We propose that the Gust-BDNF transgenic mouse models can be employed to further dissect the specific roles of BDNF in the adult taste system. PMID:22442142

Windthrow a hazard in Virginia pine strip cuttings

Treesearch

Richard H. Fenton

1955-01-01

The eye of Hurricane Hazel passed to the west of the Beltsville Experimental Forest in Maryland on the afternoon of October 15, 1954. Sustained wind velocities of 66 mph (from the SE), with maximum gusts of 98 mph, were recorded nearby.

Wind and turbine characteristics needed for integration of wind turbine arrays into a utility system

NASA Technical Reports Server (NTRS)

Park, G. L.

1982-01-01

Wind data and wind turbine generator (WTG) performance characteristics are often available in a form inconvenient for use by utility planners and engineers. The steps used by utility planners are summarized and the type of wind and WTG data needed for integration of WTG arrays suggested. These included long term yearly velocity averages for preliminary site feasibility, hourly velocities on a 'wind season' basis for more detailed economic analysis and for reliability studies, worst-case velocity profiles for gusts, and various minute-to-hourly velocity profiles for estimating the effect of longer-term wind fluctuations on utility operations. wind turbine data needed includes electrical properties of the generator, startup and shutdown characteristics, protection characteristics, pitch control response and control strategy, and electro-mechanical model for stability analysis.

An interactive driving simulation for driver control and decision-making research

NASA Technical Reports Server (NTRS)

Allen, R. W.; Hogge, J. R.; Schwartz, S. H.

1975-01-01

Display techniques and equations of motion for a relatively simple fixed base car simulation are described. The vehicle dynamics include simplified lateral (steering) and longitudinal (speed) degrees of freedom. Several simulator tasks are described which require a combination of operator control and decision making, including response to wind gust inputs, curved roads, traffic signal lights, and obstacles. Logic circuits are used to detect speeding, running red lights, and crashes. A variety of visual and auditory cues are used to give the driver appropriate performance feedback. The simulated equations of motion are reviewed and the technique for generating the line drawing CRT roadway display is discussed. On-line measurement capabilities and experimenter control features are presented, along with previous and current research results demonstrating simulation capabilities and applications.

Adaptive Control of a Transport Aircraft Using Differential Thrust

NASA Technical Reports Server (NTRS)

Stepanyan, Vahram; Krishnakumar, Kalmanje; Nguyen, Nhan

2009-01-01

The paper presents an adaptive control technique for a damaged large transport aircraft subject to unknown atmospheric disturbances such as wind gust or turbulence. It is assumed that the damage results in vertical tail loss with no rudder authority, which is replaced with a differential thrust input. The proposed technique uses the adaptive prediction based control design in conjunction with the time scale separation principle, based on the singular perturbation theory. The application of later is necessitated by the fact that the engine response to a throttle command is substantially slow that the angular rate dynamics of the aircraft. It is shown that this control technique guarantees the stability of the closed-loop system and the tracking of a given reference model. The simulation example shows the benefits of the approach.

Conceptual Design Optimization of an Augmented Stability Aircraft Incorporating Dynamic Response Performance Constraints

NASA Technical Reports Server (NTRS)

Welstead, Jason

2014-01-01

This research focused on incorporating stability and control into a multidisciplinary de- sign optimization on a Boeing 737-class advanced concept called the D8.2b. A new method of evaluating the aircraft handling performance using quantitative evaluation of the sys- tem to disturbances, including perturbations, continuous turbulence, and discrete gusts, is presented. A multidisciplinary design optimization was performed using the D8.2b transport air- craft concept. The con guration was optimized for minimum fuel burn using a design range of 3,000 nautical miles. Optimization cases were run using xed tail volume coecients, static trim constraints, and static trim and dynamic response constraints. A Cessna 182T model was used to test the various dynamic analysis components, ensuring the analysis was behaving as expected. Results of the optimizations show that including stability and con- trol in the design process drastically alters the optimal design, indicating that stability and control should be included in conceptual design to avoid system level penalties later in the design process.

Maximum likelihood identification and optimal input design for identifying aircraft stability and control derivatives

NASA Technical Reports Server (NTRS)

Stepner, D. E.; Mehra, R. K.

1973-01-01

A new method of extracting aircraft stability and control derivatives from flight test data is developed based on the maximum likelihood cirterion. It is shown that this new method is capable of processing data from both linear and nonlinear models, both with and without process noise and includes output error and equation error methods as special cases. The first application of this method to flight test data is reported for lateral maneuvers of the HL-10 and M2/F3 lifting bodies, including the extraction of stability and control derivatives in the presence of wind gusts. All the problems encountered in this identification study are discussed. Several different methods (including a priori weighting, parameter fixing and constrained parameter values) for dealing with identifiability and uniqueness problems are introduced and the results given. The method for the design of optimal inputs for identifying the parameters of linear dynamic systems is also given. The criterion used for the optimization is the sensitivity of the system output to the unknown parameters. Several simple examples are first given and then the results of an extensive stability and control dervative identification simulation for a C-8 aircraft are detailed.

NASA/MSFC FY-83 Atmospheric Research Review

NASA Technical Reports Server (NTRS)

Turner, R. E. (Compiler); Camp, D. W. (Compiler)

1983-01-01

Atmospheric research conducted at the Marshall Space Flight Center in FY 1983 is discussed. Clear air turbulence, gusts, and fog dispersal near airports is discussed. The use of Doppler Lidar signals in discussed, as are low level flow conditions that are hazardous to aircraft.

Journey in Aeronautical Research: A Career at NASA Langley Research Center. No. 12; Monographs in Aerospace History

NASA Technical Reports Server (NTRS)

Phillips, W. Hewitt

1998-01-01

An autobiography, of a noted aeronautical engineer, W. Hewitt Phillips, whose career spanned 58 years (1940-1998) at NASA Langley is presented. This work covers his early years to the Sputnik launch. His interests have been in research in aeronautics and in the related problems of spaceflight. After an introduction, his early life through the college years is reviewed, and his early interest in model airplanes is described. The first assignment for the National Advisory Committee for Aeronautics (NACA), which would later become NASA, was with the Flight Research Division. His early work involved "Flying Qualities", i.e., the stability and control characteristics of an airplane. The next chapter describes his early analytical studies. His work during World War II in the design of military airplanes, and the other effects of the war on research activities, is covered in the next two chapters. This research was involved in such innovations and refinements as the swept wing, the flettner tabs, servo tabs, spring tabs and whirlerons. The rest of the work covers the research which Mr. Hewitt was involved in, after the war until the Sputnik launch. These areas include unsteady lift, measurements of turbulence in the atmosphere, gust alleviation, and lateral response to random turbulence. He was also involved in several investigations of airplane accidents. The last two chapters cover the administration of the Langley Research Center, and the dawn of the Space Age. A complete bibliography of reports written by Mr. Hewitt, is included.

Rates and causes of accidents for general aviation aircraft operating in a mountainous and high elevation terrain environment.

PubMed

Aguiar, Marisa; Stolzer, Alan; Boyd, Douglas D

2017-10-01

Flying over mountainous and/or high elevation terrain is challenging due to rapidly changeable visibility, gusty/rotor winds and downdrafts and the necessity of terrain avoidance. Herein, general aviation accident rates and mishap cause/factors were determined (2001-2014) for a geographical region characterized by such terrain. Accidents in single piston engine-powered aircraft for states west of the US continental divide characterized by mountainous terrain and/or high elevation (MEHET) were identified from the NTSB database. MEHET-related-mishaps were defined as satisfying any one, or more, criteria (controlled flight into terrain/obstacles (CFIT), downdrafts, mountain obscuration, wind-shear, gusting winds, whiteout, instrument meteorological conditions; density altitude, dust-devil) cited as factors/causal in the NTSB report. Statistics employed Poisson distribution and contingency tables. Although the MEHET-related accident rate declined (p<0.001) 57% across the study period, the high proportion of fatal accidents showed little (40-43%) diminution (χ 2 =0.935). CFIT and wind gusts/shear were the most frequent accident cause/factor categories. For CFIT accidents, half occurred in degraded visibility with only 9% operating under instrument flight rules (IFR) and the majority (85%) involving non-turbo-charged engine-powered aircraft. For wind-gust/shear-related accidents, 44% occurred with a cross-wind exceeding the maximum demonstrated aircraft component. Accidents which should have been survivable but which nevertheless resulted in a fatal outcome were characterized by poor accessibility (60%) and shoulder harness under-utilization (41%). Despite a declining MEHET-related accident rate, these mishaps still carry an elevated risk of a fatal outcome. Airmen should be encouraged to operate in this environment utilizing turbo-charged-powered airplanes and flying under IFR to assure terrain clearance. Copyright © 2017 Elsevier Ltd. All rights reserved.

Coupled nonlinear aeroelasticity and flight dynamics of fully flexible aircraft

NASA Astrophysics Data System (ADS)

Su, Weihua

This dissertation introduces an approach to effectively model and analyze the coupled nonlinear aeroelasticity and flight dynamics of highly flexible aircraft. A reduced-order, nonlinear, strain-based finite element framework is used, which is capable of assessing the fundamental impact of structural nonlinear effects in preliminary vehicle design and control synthesis. The cross-sectional stiffness and inertia properties of the wings are calculated along the wing span, and then incorporated into the one-dimensional nonlinear beam formulation. Finite-state unsteady subsonic aerodynamics is used to compute airloads along lifting surfaces. Flight dynamic equations are then introduced to complete the aeroelastic/flight dynamic system equations of motion. Instead of merely considering the flexibility of the wings, the current work allows all members of the vehicle to be flexible. Due to their characteristics of being slender structures, the wings, tail, and fuselage of highly flexible aircraft can be modeled as beams undergoing three dimensional displacements and rotations. New kinematic relationships are developed to handle the split beam systems, such that fully flexible vehicles can be effectively modeled within the existing framework. Different aircraft configurations are modeled and studied, including Single-Wing, Joined-Wing, Blended-Wing-Body, and Flying-Wing configurations. The Lagrange Multiplier Method is applied to model the nodal displacement constraints at the joint locations. Based on the proposed models, roll response and stability studies are conducted on fully flexible and rigidized models. The impacts of the flexibility of different vehicle members on flutter with rigid body motion constraints, flutter in free flight condition, and roll maneuver performance are presented. Also, the static stability of the compressive member of the Joined-Wing configuration is studied. A spatially-distributed discrete gust model is incorporated into the time simulation of the framework. Gust responses of the Flying-Wing configuration subject to stall effects are investigated. A bilinear torsional stiffness model is introduced to study the skin wrinkling due to large bending curvature of the Flying-Wing. The numerical studies illustrate the improvements of the existing reduced-order formulation with new capabilities of both structural modeling and coupled aeroelastic and flight dynamic analysis of fully flexible aircraft.

14 CFR 23.253 - High speed characteristics.

Code of Federal Regulations, 2013 CFR

2013-01-01

... and characteristics include gust upsets, inadvertent control movements, low stick force gradients in relation to control friction, passenger movement, leveling off from climb, and descent from Mach to... normal attitude and its speed reduced to VMO/MMO, without— (1) Exceptional piloting strength or skill; (2...

14 CFR 23.253 - High speed characteristics.

Code of Federal Regulations, 2014 CFR

2014-01-01

... and characteristics include gust upsets, inadvertent control movements, low stick force gradients in relation to control friction, passenger movement, leveling off from climb, and descent from Mach to... normal attitude and its speed reduced to VMO/MMO, without— (1) Exceptional piloting strength or skill; (2...

Flight Control of Flexible Aircraft

NASA Technical Reports Server (NTRS)

Nguyen, Nhan T.

2017-01-01

This presentation presents an overview of flight control research for flexible high aspect wing aircraft in support of the NASA ARMD Advanced Air Transport Technology (AATT) project. It summarizes multi-objective flight control technology being developed for drag optimization, flutter suppression, and maneuver and gust load alleviation.

Gusts of power

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1994-01-01

This report reviews research on agricultural applications of wind energy. Shows irrigation projects in Bushland, TX, and Garden City, KS; cooling of milking parlor in Fort Collins, CO; heating a home in Bloomfield, IA; cooling stored apples in Blacksburg, VA; and an experimental water heating project in Ithaca, NY.

Gusts of power

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

1994-12-31

This report reviews research on agricultural applications of wind energy. Shows irrigation projects in Bushland, TX, and Garden City, KS; cooling of milking parlor in Fort Collins, CO; heating a home in Bloomfield, IA; cooling stored apples in Blacksburg, VA; and an experimental water heating project in Ithaca, NY.

Convective cell development and propagation in a mesoscale convective complex

NASA Technical Reports Server (NTRS)

Ahn, Yoo-Shin; Brundidge, Kenneth C.

1987-01-01

A case study was made of the mesoscale convective complex (MCC) which occurred over southern Oklahoma and northern Texas on 27 May 1981. This storm moved in an eastsoutheasterly direction and during much of its lifetime was observable by radars at Oklahoma City, Ok. and Stephenville, Tx. It was found that the direction of cell (VIP level 3 or more reflectivity) propagation was somewhat erratic but approximately the same as the system (VIP level 1 reflectivity) movement and the ambient wind. New cells developed along and behind the gust front make it appear that once the MCC is initiated, a synergistic relationship exists between the gust front and the MCC. The relationship between rainfall patterns and amounts and the infrared (IR) temperature field in the satellite imagery were examined. The 210 K isotherm of GOES IR imagery was found to encompass the rain area of the storm. The heaviest rainfall was in the vicinity of the VIP level 3 cells and mostly contained within the 205 K isotherm of GOES IR imagery.

Role of surface heat fluxes underneath cold pools

DOE PAGES

Gentine, Pierre; Garelli, Alix; Park, Seung -Bu; ...

2016-01-05

In this paper, the role of surface heat fluxes underneath cold pools is investigated using cloud–resolving simulations with either interactive or horizontally homogenous surface heat fluxes over an ocean and a simplified land surface. Over the ocean, there are limited changes in the distribution of the cold pool temperature, humidity, and gust front velocity, yet interactive heat fluxes induce more cold pools, which are smaller, and convection is then less organized. Correspondingly, the updraft mass flux and lateral entrainment are modified. Over the land surface, the heat fluxes underneath cold pools drastically impact the cold pool characteristics with more numerousmore » and smaller pools, which are warmer and more humid and accompanied by smaller gust front velocities. The interactive fluxes also modify the updraft mass flux and reduce convective organization. These results emphasize the importance of interactive surface fluxes instead of prescribed flux boundary conditions, as well as the formulation of surface heat fluxes, when studying convection.« less

Measured Noise from Small Unmanned Aerial Vehicles

NASA Technical Reports Server (NTRS)

Cabell, Randolph; McSwain, Robert; Grosveld, Ferdinand

2016-01-01

Proposed uses of small unmanned aerial vehicles (UAVs), including home package delivery, have the potential to expose large portions of communities to a new noise source. This paper discusses results of flyover noise measurements of four small UAVs, including an internal combustion-powered model airplane and three battery-powered multicopters. Basic noise characteristics of these vehicles are discussed, including spectral properties and sound level metrics such as sound pressure level, effective perceived noise level, and sound exposure level. The size and aerodynamic characteristics of the multicopters in particular make their flight path susceptible to atmospheric disturbances such as wind gusts. These gusts, coupled with a flight control system that varies rotor speed to maintain vehicle stability, create an unsteady acoustic signature. The spectral variations resulting from this unsteadiness are explored, in both hover and flyover conditions for the multicopters. The time varying noise, which differs from the relatively steady noise generated by large transport aircraft, may complicate the prediction of human annoyance using conventional sound level metrics.

A conceptual framework for using Doppler radar acquired atmospheric data for flight simulation

NASA Technical Reports Server (NTRS)

Campbell, W.

1983-01-01

A concept is presented which can permit turbulence simulation in the vicinity of microbursts. The method involves a large data base, but should be fast enough for use with flight simulators. The model permits any pilot to simulate any flight maneuver in any aircraft. The model simulates a wind field with three-component mean winds and three-component turbulent gusts, and gust variation over the body of an aircraft so that all aerodynamic loads and moments can be calculated. The time and space variation of mean winds and turbulent intensities associated with a particular atmospheric phenomenon such as a microburst is used in the model. In fact, Doppler radar data such as provided by JAWS is uniquely suited for use with the proposed model. The concept is completely general and is not restricted to microburst studies. Reentry and flight in terrestrial or planetary atmospheres could be realistically simulated if supporting data of sufficient resolution were available.

Gust wind tunnel study on ballast pick-up by high-speed trains

NASA Astrophysics Data System (ADS)

Navarro-Medina, F.; Sanz-Andres, A.; Perez-Grande, I.

2012-01-01

This paper describes the experimental setup, procedure, and results obtained, concerning the dynamics of a body lying on a floor, attached to a hinge, and exposed to an unsteady flow, which is a model of the initiation of rotational motion of ballast stones due to the wind generated by the passing of a high-speed train. The idea is to obtain experimental data to support the theoretical model developed in Sanz-Andres and Navarro-Medina (J Wind Eng Ind Aerodyn 98, 772-783, (2010), aimed at analyzing the initial phase of the ballast train-induced-wind erosion (BATIWE) phenomenon. The experimental setup is based on an open circuit, closed test section, low-speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the IDR/UPM. The tunnel's main characteristic is the ability to generate a flow with a uniform velocity profile and sinusoidal time fluctuation of the speed. Experimental results and theoretical model predictions are in good agreement.

The Total In-Flight Simulator (TIFS) aerodynamics and systems: Description and analysis. [maneuver control and gust alleviators

NASA Technical Reports Server (NTRS)

Andrisani, D., II; Daughaday, H.; Dittenhauser, J.; Rynaski, E.

1978-01-01

The aerodynamics, control system, instrumentation complement and recording system of the USAF Total In/Flight Simulator (TIFS) airplane are described. A control system that would allow the ailerons to be operated collectively, as well as, differentially to entrance the ability of the vehicle to perform the dual function of maneuver load control and gust alleviation is emphasized. Mathematical prediction of the rigid body and the flexible equations of longitudinal motion using the level 2.01 FLEXSTAB program are included along with a definition of the vehicle geometry, the mass and stiffness distribution, the calculated mode frequencies and mode shapes, and the resulting aerodynamic equations of motion of the flexible vehicle. A complete description of the control and instrumentation system of the aircraft is presented, including analysis, ground test and flight data comparisons of the performance and bandwidth of the aerodynamic surface servos. Proposed modification for improved performance of the servos are also presented.

Poster 17: Methane storms as a driver of Titan's dune orientation.

NASA Astrophysics Data System (ADS)

Charnay, Benjamin; Barth, Erika; Rafkin, Scot; Narteau, Clement; Lebonnois, Sebastien; Rodriguez, Sebastien; Courech Du Pont, Sylvain; Lucas, Antoine

2016-06-01

Titan's equatorial regions are covered by eastward oriented linear dunes [1,2]. This direction is opposite to mean surface winds simulated by Global Climate Models (GCMs) at these latitudes, oriented westward as trade winds on Earth. We propose that Titan's dune orientation is actually determined by equinoctial tropical methane storms producing a coupling with superrotation and dune formation [3]. Using meso-scale simulations of convective methane clouds [4] with a GCM wind profile featuring the superrotation [5,6], we show that Titan's storms should produce fast eastward gust fronts above the surface. Such gusts dominate the aeolian transport. Using GCM wind calculations and analogies with terrestrial dune fields [7], we show that Titan's dune propagation occurs eastward under these conditions. Finally, this scenario combining global circulation winds and methane storms can explain other major features of Titan's dunes as the divergence from the equator or the dune size and spacing. It also implies an equatorial origin of Titan's dune sand and a possible occurence of dust storms.

14 CFR 25.333 - Flight maneuvering envelope.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Flight maneuvering envelope. 25.333 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.333 Flight maneuvering envelope. (a) General. The strength requirements must be met at each combination of...

14 CFR 25.333 - Flight maneuvering envelope.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 1 2014-01-01 2014-01-01 false Flight maneuvering envelope. 25.333 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Flight Maneuver and Gust Conditions § 25.333 Flight maneuvering envelope. (a) General. The strength requirements must be met at each combination of...

14 CFR 25.349 - Rolling conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... zero and of two-thirds of the positive maneuvering factor used in design. In determining the required... other weight concentrations outboard of the fuselage. For the angular acceleration conditions, zero... less than one-third of that in paragraph (a)(2) of this section. (b) Unsymmetrical gusts. The airplane...

14 CFR 25.335 - Design airspeeds.

Code of Federal Regulations, 2013 CFR

2013-01-01

... cruise speed (knots equivalent airspeed); Uref=the reference gust velocity (feet per second equivalent... control of airspeed and for transition from one flap position to another. (2) If an automatic flap... speed recommended for the operation of the device to allow for probable variations in speed control. For...

14 CFR 25.335 - Design airspeeds.

Code of Federal Regulations, 2014 CFR

2014-01-01

... cruise speed (knots equivalent airspeed); Uref=the reference gust velocity (feet per second equivalent... control of airspeed and for transition from one flap position to another. (2) If an automatic flap... speed recommended for the operation of the device to allow for probable variations in speed control. For...

14 CFR 25.335 - Design airspeeds.

Code of Federal Regulations, 2012 CFR

2012-01-01

... cruise speed (knots equivalent airspeed); Uref=the reference gust velocity (feet per second equivalent... control of airspeed and for transition from one flap position to another. (2) If an automatic flap... speed recommended for the operation of the device to allow for probable variations in speed control. For...

14 CFR 25.335 - Design airspeeds.

Code of Federal Regulations, 2011 CFR

2011-01-01

... cruise speed (knots equivalent airspeed); Uref=the reference gust velocity (feet per second equivalent... control of airspeed and for transition from one flap position to another. (2) If an automatic flap... speed recommended for the operation of the device to allow for probable variations in speed control. For...

Learning Completable Reactive Plans through Achievability Proofs

DTIC Science & Technology

1990-05-01

34 Proceedings of The Eleventh International Joint Conference on Artificial Intelligence, Detroit, MI, Au- gust 1989, pp. 918-923. [Thomas68] G. B. Thomas ... Calculus and Analytic Geometry, Addison-Wesley, Reading, MA, 1968. [Tumey89] J. Turney and A. Segre, "SEPIA: An Experiment in Integrated Planning and

Data Mining of NASA Boeing 737 Flight Data: Frequency Analysis of In-Flight Recorded Data

NASA Technical Reports Server (NTRS)

Butterfield, Ansel J.

2001-01-01

Data recorded during flights of the NASA Trailblazer Boeing 737 have been analyzed to ascertain the presence of aircraft structural responses from various excitations such as the engine, aerodynamic effects, wind gusts, and control system operations. The NASA Trailblazer Boeing 737 was chosen as a focus of the study because of a large quantity of its flight data records. The goal of this study was to determine if any aircraft structural characteristics could be identified from flight data collected for measuring non-structural phenomena. A number of such data were examined for spatial and frequency correlation as a means of discovering hidden knowledge of the dynamic behavior of the aircraft. Data recorded from on-board dynamic sensors over a range of flight conditions showed consistently appearing frequencies. Those frequencies were attributed to aircraft structural vibrations.

Lewis Research Center studies of multiple large wind turbine generators on a utility network

NASA Technical Reports Server (NTRS)

Gilbert, L. J.; Triezenberg, D. M.

1979-01-01

A NASA-Lewis program to study the anticipated performance of a wind turbine generator farm on an electric utility network is surveyed. The paper describes the approach of the Lewis Wind Energy Project Office to developing analysis capabilities in the area of wind turbine generator-utility network computer simulations. Attention is given to areas such as, the Lewis Purdue hybrid simulation, an independent stability study, DOE multiunit plant study, and the WEST simulator. Also covered are the Lewis mod-2 simulation including analog simulation of a two wind turbine system and comparison with Boeing simulation results, and gust response of a two machine model. Finally future work to be done is noted and it is concluded that the study shows little interaction between the generators and between the generators and the bus.

Typhoon Neoguri in the East China Sea

NASA Image and Video Library

2017-12-08

The MODIS instrument on NASA's Aqua satellite captured Typhoon Neoguri in the East China Sea at 05:00 UTC (1:00 AM EDT) on July 8, 2014. Typhoon Neoguri hit Japan’s Okinawa islands on Tuesday local time (July 8, 2014), bringing high winds, huge waves and storm surges. Neoguri packed sustained winds of 175 kilometers (108 miles) per hour with some gusts up to 250 kph (154 mph), according to the Japan Meteorological Agency. Credit: NASA/GSFC/Jeff Schmaltz/MODIS Land Rapid Response NASA image use policy. NASA Goddard Space Flight Center enables NASA’s mission through four scientific endeavors: Earth Science, Heliophysics, Solar System Exploration, and Astrophysics. Goddard plays a leading role in NASA’s accomplishments by contributing compelling scientific knowledge to advance the Agency’s mission. Follow us on Twitter Like us on Facebook Find us on Instagram

An airborne FLIR detection and warning system for low altitude wind shear

NASA Technical Reports Server (NTRS)

Sinclair, Peter C.; Kuhn, Peter M.

1991-01-01

It is shown through some preliminary flight measurement research that a forward looking infrared radiometer (FLIR) system can be used to successfully detect the cool downdraft of downbursts (microbusts/macrobursts) and thunderstorm gust front outflows that are responsible for most of the low altitude wind shear (LAWS) events. The FLIR system provides a much greater safety margin for the pilot than that provided by reactive designs such as inertial air speed systems. Preliminary results indicate that an advanced airborne FLIR system could provide the pilot with remote indication of microburst (MB) hazards along the flight path ahead of the aircraft. Results of a flight test of a prototype FLIR system show that a minimum warning time of one to four minutes (5 to 10 km), depending on aircraft speed, is available to the pilot prior to the microburst encounter.

Contributions to the simulation of turbulence

NASA Technical Reports Server (NTRS)

Dutton, J. A.; Kerman, B. R.; Petersen, E. L.

1976-01-01

The simulation modeling of turbulence in the boundary layer in consolidated in terms of boundary layer similarity principles and empirical results. The modeling is extended for some aspects of the nonlinear and non-Gaussian structure of the turbulence. Properties of the discrete gust form structure of the modeled turbulence are identified.

40 CFR 610.64 - Track test procedures.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 31 2012-07-01 2012-07-01 false Track test procedures. 610.64 Section 610.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL... necessary to limit testing to times when the wind velocity is less than 5 mph, with gusts less than 10 mph...

40 CFR 610.64 - Track test procedures.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 31 2013-07-01 2013-07-01 false Track test procedures. 610.64 Section 610.64 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL... necessary to limit testing to times when the wind velocity is less than 5 mph, with gusts less than 10 mph...

Terminal Information Processing System (TIPS) Consolidated CAB Display (CCD) Comparative Analysis.

DTIC Science & Technology

1982-04-01

Barometric pressure 3. Center field wind speed, direction and gusts 4. Runway visual range 5. Low-level wind shear 6. Vortex advisory 7. Runway equipment...PASSWORD Command (standard user) u. PAUSE Command (standard user) v. PMSG Command (standard user) w. PPD Command (standard user) x. PURGE Command (standard

Passive Infrared Detection of Microburst Induced Low Level Wind Shear

DTIC Science & Technology

1990-05-17

ring vortex breaks up as the microburst matures. Some rotor microbursts develops from larger scale macrobursts and gust fronts. From Fujita (1985) 2.2...Canada, Amer. Meteor. Soc., 638-645. , 1985:" The Downburst; Microburst and Macroburst ", University of Chicago, SRMP, University of Chicago. , 1986

Monitoring of wind load and response for cable-supported bridges in Hong Kong

NASA Astrophysics Data System (ADS)

Wong, Kai-yuen; Chan, Wai-Yee K.; Man, King-Leung

2001-08-01

Structural health monitoring for the three cable-supported bridges located in the West of Hong Kong or the Tsing Ma Control Area has been carried out since the opening of these bridges to public traffic. The three cable-supported bridges are referred to as the Tsing Ma (suspension) Bridge, the Kap Shui Mun (cable-stayed) Bridge and the Ting Kau (cable-stayed) Bridge. The structural health monitoring works involved are classified as six monitoring categories, namely, wind load and response, temperature load and response, traffic load and response, geometrical configuration monitoring, strains and stresses/forces monitoring and global dynamic characteristics monitoring. As wind loads and responses had been a major concern in the design and construction stages, this paper therefore outlines the work of wind load and response monitoring on Tsing Ma, Kap Shui Mun and Ting Kau Bridges. The paper starts with a brief description of the sensory systems. The description includes the layout and performance requirements of sensory systems for wind load and responses monitoring. Typical results of wind load and response monitoring in graphical forms are then presented. These graphical forms include the plots of wind rose diagrams, wind incidences vs wind speeds, wind turbulence intensities, wind power spectra, gust wind factors, coefficient of terrain roughness, extreme wind analyses, deck deflections/rotations vs wind speeds, acceleration spectra, acceleration/displacement contours, and stress demand ratios. Finally conclusions on wind load and response monitoring on the three cable-supported bridges are drawn.

Automated Blazar Light Curves Using Machine Learning

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Spencer James

Every night in a remote clearing called Fenton Hill high in the Jemez Mountains of central New Mexico, a bank of robotically controlled telescopes tilt their lenses to the sky for another round of observation through digital imaging. Los Alamos National Laboratory’s Thinking Telescopes project is watching for celestial transients including high-power cosmic flashes called, and like all science, it can be messy work. To keep the project clicking along, Los Alamos scientists routinely install equipment upgrades, maintain the site, and refine the sophisticated machinelearning computer programs that process those images and extract useful data from them. Each week themore » system amasses 100,000 digital images of the heavens, some of which are compromised by clouds, wind gusts, focus problems, and so on. For a graduate student at the Lab taking a year’s break between master’s and Ph.D. studies, working with state-of-the-art autonomous telescopes that can make fundamental discoveries feels light years beyond the classroom.« less

Predicting Flutter and Forced Response in Turbomachinery

NASA Technical Reports Server (NTRS)

VanZante, Dale E.; Adamczyk, John J.; Srivastava, Rakesh; Bakhle, Milind A.; Shabbir, Aamir; Chen, Jen-Ping; Janus, J. Mark; To, Wai-Ming; Barter, John

2005-01-01

TURBO-AE is a computer code that enables detailed, high-fidelity modeling of aeroelastic and unsteady aerodynamic characteristics for prediction of flutter, forced response, and blade-row interaction effects in turbomachinery. Flow regimes that can be modeled include subsonic, transonic, and supersonic, with attached and/or separated flow fields. The three-dimensional Reynolds-averaged Navier-Stokes equations are solved numerically to obtain extremely accurate descriptions of unsteady flow fields in multistage turbomachinery configurations. Blade vibration is simulated by use of a dynamic-grid-deformation technique to calculate the energy exchange for determining the aerodynamic damping of vibrations of blades. The aerodynamic damping can be used to assess the stability of a blade row. TURBO-AE also calculates the unsteady blade loading attributable to such external sources of excitation as incoming gusts and blade-row interactions. These blade loadings, along with aerodynamic damping, are used to calculate the forced responses of blades to predict their fatigue lives. Phase-lagged boundary conditions based on the direct-store method are used to calculate nonzero interblade phase-angle oscillations; this practice eliminates the need to model multiple blade passages, and, hence, enables large savings in computational resources.

The design of a turboshaft speed governor using modern control techniques

NASA Technical Reports Server (NTRS)

Delosreyes, G.; Gouchoe, D. R.

1986-01-01

The objectives of this program were: to verify the model of off schedule compressor variable geometry in the T700 turboshaft engine nonlinear model; to evaluate the use of the pseudo-random binary noise (PRBN) technique for obtaining engine frequency response data; and to design a high performance power turbine speed governor using modern control methods. Reduction of T700 engine test data generated at NASA-Lewis indicated that the off schedule variable geometry effects were accurate as modeled. Analysis also showed that the PRBN technique combined with the maximum likelihood model identification method produced a Bode frequency response that was as accurate as the response obtained from standard sinewave testing methods. The frequency response verified the accuracy of linear models consisting of engine partial derivatives and used for design. A power turbine governor was designed using the Linear Quadratic Regulator (LQR) method of full state feedback control. A Kalman filter observer was used to estimate helicopter main rotor blade velocity. Compared to the baseline T700 power turbine speed governor, the LQR governor reduced droop up to 25 percent for a 490 shaft horsepower transient in 0.1 sec simulating a wind gust, and up to 85 percent for a 700 shaft horsepower transient in 0.5 sec simulating a large collective pitch angle transient.

LES-based generation of high-frequency fluctuation in wind turbulence obtained by meteorological model

NASA Astrophysics Data System (ADS)

Tamura, Tetsuro; Kawaguchi, Masaharu; Kawai, Hidenori; Tao, Tao

2017-11-01

The connection between a meso-scale model and a micro-scale large eddy simulation (LES) is significant to simulate the micro-scale meteorological problem such as strong convective events due to the typhoon or the tornado using LES. In these problems the mean velocity profiles and the mean wind directions change with time according to the movement of the typhoons or tornadoes. Although, a fine grid micro-scale LES could not be connected to a coarse grid meso-scale WRF directly. In LES when the grid is suddenly refined at the interface of nested grids which is normal to the mean advection the resolved shear stresses decrease due to the interpolation errors and the delay of the generation of smaller scale turbulence that can be resolved on the finer mesh. For the estimation of wind gust disaster the peak wind acting on buildings and structures has to be correctly predicted. In the case of meteorological model the velocity fluctuations have a tendency of diffusive variation without the high frequency component due to the numerically filtering effects. In order to predict the peak value of wind velocity with good accuracy, this paper proposes a LES-based method for generating the higher frequency components of velocity and temperature fields obtained by meteorological model.

Least square based sliding mode control for a quad-rotor helicopter and energy saving by chattering reduction

NASA Astrophysics Data System (ADS)

Sumantri, Bambang; Uchiyama, Naoki; Sano, Shigenori

2016-01-01

In this paper, a new control structure for a quad-rotor helicopter that employs the least squares method is introduced. This proposed algorithm solves the overdetermined problem of the control input for the translational motion of a quad-rotor helicopter. The algorithm allows all six degrees of freedom to be considered to calculate the control input. The sliding mode controller is applied to achieve robust tracking and stabilization. A saturation function is designed around a boundary layer to reduce the chattering phenomenon that is a common problem in sliding mode control. In order to improve the tracking performance, an integral sliding surface is designed. An energy saving effect because of chattering reduction is also evaluated. First, the dynamics of the quad-rotor helicopter is derived by the Newton-Euler formulation for a rigid body. Second, a constant plus proportional reaching law is introduced to increase the reaching rate of the sliding mode controller. Global stability of the proposed control strategy is guaranteed based on the Lyapunov's stability theory. Finally, the robustness and effectiveness of the proposed control system are demonstrated experimentally under wind gusts, and are compared with a regular sliding mode controller, a proportional-differential controller, and a proportional-integral-differential controller.

78 FR 42480 - Harmonization of Airworthiness Standards-Gust and Maneuver Load Requirements

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-16

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 25 [Docket No.: FAA-2013... Requirements Correction In proposed rule document 2013-12445 appearing on pages 31851-31860 in the issue of... issue of Monday, June 24, 2013, make the following correction: Sec. 25.341 [Corrected] 2. In the third...

Using Kites to Illustrate Some Features of Boundary Layer Winds.

ERIC Educational Resources Information Center

Tuller, Stanton E.

1983-01-01

Kites allow teachers to illustrate wind patterns by calling on past experience and by present demonstration. Features of the wind illustrated by kites--the effect of surface friction on wind speed, change of wind direction with elevation, gust and lull sequence, and atmospheric stability and turbulence type--are discussed. (SR)

MARINE NEWS - GRIDDED and VECTOR DATA

Science.gov Websites

Great Lakes. Experimental gridded data and graphical imagery is now routinely produced at most WFOs. It gusts; weather; and wave height by December 2004. Gridded forecasts from the other non-continental U.S (PNG) format. Links to NDFD Data: Example of NDFD Graphical Imagery (experimental) NDFD GRIB2 data via

14 CFR 25.341 - Gust and turbulence loads.

Code of Federal Regulations, 2010 CFR

2010-01-01

... accordance with the provisions: (1) Loads on each part of the structure must be determined by dynamic...: EN08MR96.004 Zmo=Maximum operating altitude defined in § 25.1527. (7) When a stability augmentation system is included in the analysis, the effect of any significant system nonlinearities should be accounted...

Interactions of Airfoils with Gusts and Concentrated Vortices in Unsteady Transonic Flow,

DTIC Science & Technology

1983-01-01

ain(U, u, ) bances into the solution domain. One such smooth- ,ui ,j ing method was recently demonstrated by Murman and Stremel ,10 who distributed...were qualitatively similar to the predic- °Murman, E. M. and Stremel , P. M., "A Vortex tions of linear theory, but important quantitative Wake

Overview: Performance Adaptive Aeroelastic Wing

NASA Technical Reports Server (NTRS)

Hashemi, Kelley

2017-01-01

An overview of recent aeroelasitc wing-shaping work at the NASA Ames Research Center is presented. The highlight focuses on activity related to the Performance Adaptive Aeroelastic Wing concept and related Variable Camber Continuous Trailing Edge Flap actuation system. Topics covered include drag-reducing configurations and online algorithms, gust and maneuver load techniques, and wind tunnel demonstrations.

Kaman 40 kW wind turbine generator - control system dynamics

NASA Technical Reports Server (NTRS)

Perley, R.

1981-01-01

The generator design incorporates an induction generator for application where a utility line is present and a synchronous generator for standalone applications. A combination of feed forward and feedback control is used to achieve synchronous speed prior to connecting the generator to the load, and to control the power level once the generator is connected. The dynamics of the drive train affect several aspects of the system operation. These were analyzed to arrive at the required shaft stiffness. The rotor parameters that affect the stability of the feedback control loop vary considerably over the wind speed range encountered. Therefore, the controller gain was made a function of wind speed in order to maintain consistent operation over the whole wind speed range. The velocity requirement for the pitch control mechanism is related to the nature of the wind gusts to be encountered, the dynamics of the system, and the acceptable power fluctuations and generator dropout rate. A model was developed that allows the probable dropout rate to be determined from a statistical model of wind gusts and the various system parameters, including the acceptable power fluctuation.

Flight Tests on U.S.S. Los Angeles. Part I : Full Scale Pressure Distribution Investigation

NASA Technical Reports Server (NTRS)

De France, S J

1930-01-01

The primary purpose of this investigation was to obtain simultaneous data on the loads and stress experience in flight by the U. S. S. Los Angeles which could be used in rigid airship structure design. A secondary object of the investigation was to determine the turning and drag characteristics of the airship. The aerodynamic loading was obtained by measuring the pressure at 95 locations on the tail surfaces, 54 on the hull, and 5 on the passenger car. These measurements were made during a series of maneuvers consisting of turns and reversals in smooth air and during a cruise in rough air which was just short of squall proportions. The results of the pressure measurements on the hull indicate that the forces on the forebody of an airship are relatively small. The tail surface measurements show conclusively that the forces caused by gusts are much greater than those caused by horizontal maneuvers. In this investigation the tail surface loadings caused by gusts closely approached the designed loads of the tail structure. The turning and drag characteristics will be reported in separate reports.

Flutter suppression and gust alleviation using active controls

NASA Technical Reports Server (NTRS)

Nissim, E.

1974-01-01

The effects of active controls on the suppression of flutter and gust alleviation of two different types of subsonic aircraft (the Arava, twin turboprop STOL transport, and the Westwind twin-jet business transport) are investigated. The active controls are introduced in pairs which include, in any chosen wing strip, a leading-edge (LE) control and a trailing-edge (TE) control. Each control surface is allowed to be driven by a combined linear-rotational sensor system, located on the activated strip. The control law, which translates the sensor signals into control surface rotations, is based on the concept of aerodynamic energy. The results indicate the extreme effectiveness of the active systems in controlling flutter. A single system spanning 10% of the wing semispan made the Arava flutter-free, and a similar active system, for the Westwind aircraft, yielded a reduction of 75% in the maximum bending moment of the wing and a reduction of 90% in the acceleration of the cg of the aircraft. Results for simultaneous activation of several LE - TE systems are presented. Further work needed to bring the investigation to completion is also discussed.

GIS-based estimation of the winter storm damage probability in forests: a case study from Baden-Wuerttemberg (Southwest Germany).

PubMed

Schindler, Dirk; Grebhan, Karin; Albrecht, Axel; Schönborn, Jochen; Kohnle, Ulrich

2012-01-01

Data on storm damage attributed to the two high-impact winter storms 'Wiebke' (28 February 1990) and 'Lothar' (26 December 1999) were used for GIS-based estimation and mapping (in a 50 × 50 m resolution grid) of the winter storm damage probability (P(DAM)) for the forests of the German federal state of Baden-Wuerttemberg (Southwest Germany). The P(DAM)-calculation was based on weights of evidence (WofE) methodology. A combination of information on forest type, geology, soil type, soil moisture regime, and topographic exposure, as well as maximum gust wind speed field was used to compute P(DAM) across the entire study area. Given the condition that maximum gust wind speed during the two storm events exceeded 35 m s(-1), the highest P(DAM) values computed were primarily where coniferous forest grows in severely exposed areas on temporarily moist soils on bunter sandstone formations. Such areas are found mainly in the mountainous ranges of the northern Black Forest, the eastern Forest of Odes, in the Virngrund area, and in the southwestern Alpine Foothills.

A concentrated outbreak of tornadoes, downbursts and microbursts, and implications regarding vortex classification

NASA Technical Reports Server (NTRS)

Forbes, G. S.; Wakimoto, R. M.

1983-01-01

A remarkable case of severe weather occurred near Springfield, Illinois on 6 August 1977. Aerial and ground surveys revealed that 17 cyclonic vortices, an anticyclonic vortex, 10 downbursts and 19 microbursts occurred in a limited (20 km x 40 km) area, associated with a bow-shaped radar echo. About half of the vortices appeared to have occurred along a gust front. Some of the others appear to have occurred within the circulation of a mesocyclone accompanying the bow echo, but these vortices seem to have developed specifically in response to localized boundary-layer vorticity generation associated with horizontal and vertical wind shears on the periphery of microbursts. Some of these vortices, and other destructive vortices in the literature, do not qualify as tornadoes as defined in the Glossary of Meteorology. A more pragmatic definition of a tornado is suggested.

Transient airload computer analysis for simulating wind induced impulsive noise conditions of a hovering helicopter rotor

NASA Technical Reports Server (NTRS)

Hall, G. F.

1975-01-01

A numerical analysis was developed to determine the airloads on helicopter rotors operating under near-hovering flight conditions capable of producing impulsive noise. A computer program was written in which the solutions for the rotor tip vortex geometry, inflow, aeroelastic response, and airloads are solved in a coupled manner at sequential time steps, with or without the influence of an imposed steady ambient wind or transient gust. The program was developed for future applications in which predicted airloads would be incorporated in an acoustics analysis to attempt to predict and analyze impulsive noise (blade slap). The analysis was applied to a hovering full-scale rotor for which impulsive noise was recorded in the presence of ambient wind. The predicted tip vortex coordinates are in reasonable agreement with the test data, and the blade airload solutions converged to a periodic behavior for an imposed steady ambient wind conditions.

Acute melioidosis outbreak in Western Australia.

PubMed Central

Inglis, T. J.; Garrow, S. C.; Adams, C.; Henderson, M.; Mayo, M.; Currie, B. J.

1999-01-01

A cluster of acute melioidosis cases occurred in a remote, coastal community in tropical Western Australia. Molecular typing of Burkholderia pseudomallei isolates from culture-confirmed cases and suspected environmental sources by pulsed-field gel electrophoresis (PFGE) of XbaI chromosomal DNA digests showed that a single PFGE type was responsible for five cases of acute infection in a community of around 300 during a 5 week period. This temporal and geographical clustering of acute melioidosis cases provided a unique opportunity to investigate the environmental factors contributing to this disease. B. pseudomallei isolated from a domestic tap at the home of an asymptomatic seroconverter was indistinguishable by PFGE. Possible contributing environmental factors included an unusually acid communal water supply, unrecordable chlorine levels during the probable exposure period, a nearby earth tremor, and gusting winds during the installation of new water and electricity supplies. The possible role of the potable water supply as a source of B. pseudomallei was investigated further. PMID:10694154

Acute melioidosis outbreak in Western Australia.

PubMed

Inglis, T J; Garrow, S C; Adams, C; Henderson, M; Mayo, M; Currie, B J

1999-12-01

A cluster of acute melioidosis cases occurred in a remote, coastal community in tropical Western Australia. Molecular typing of Burkholderia pseudomallei isolates from culture-confirmed cases and suspected environmental sources by pulsed-field gel electrophoresis (PFGE) of XbaI chromosomal DNA digests showed that a single PFGE type was responsible for five cases of acute infection in a community of around 300 during a 5 week period. This temporal and geographical clustering of acute melioidosis cases provided a unique opportunity to investigate the environmental factors contributing to this disease. B. pseudomallei isolated from a domestic tap at the home of an asymptomatic seroconverter was indistinguishable by PFGE. Possible contributing environmental factors included an unusually acid communal water supply, unrecordable chlorine levels during the probable exposure period, a nearby earth tremor, and gusting winds during the installation of new water and electricity supplies. The possible role of the potable water supply as a source of B. pseudomallei was investigated further.

Small UAS-Based Wind Feature Identification System Part 1: Integration and Validation

PubMed Central

Rodriguez Salazar, Leopoldo; Cobano, Jose A.; Ollero, Anibal

2016-01-01

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz. Predictions show a convergence time with a 95% confidence interval of approximately 30 s. PMID:28025531

Small UAS-Based Wind Feature Identification System Part 1: Integration and Validation.

PubMed

Rodriguez Salazar, Leopoldo; Cobano, Jose A; Ollero, Anibal

2016-12-23

This paper presents a system for identification of wind features, such as gusts and wind shear. These are of particular interest in the context of energy-efficient navigation of Small Unmanned Aerial Systems (UAS). The proposed system generates real-time wind vector estimates and a novel algorithm to generate wind field predictions. Estimations are based on the integration of an off-the-shelf navigation system and airspeed readings in a so-called direct approach. Wind predictions use atmospheric models to characterize the wind field with different statistical analyses. During the prediction stage, the system is able to incorporate, in a big-data approach, wind measurements from previous flights in order to enhance the approximations. Wind estimates are classified and fitted into a Weibull probability density function. A Genetic Algorithm (GA) is utilized to determine the shaping and scale parameters of the distribution, which are employed to determine the most probable wind speed at a certain position. The system uses this information to characterize a wind shear or a discrete gust and also utilizes a Gaussian Process regression to characterize continuous gusts. The knowledge of the wind features is crucial for computing energy-efficient trajectories with low cost and payload. Therefore, the system provides a solution that does not require any additional sensors. The system architecture presents a modular decentralized approach, in which the main parts of the system are separated in modules and the exchange of information is managed by a communication handler to enhance upgradeability and maintainability. Validation is done providing preliminary results of both simulations and Software-In-The-Loop testing. Telemetry data collected from real flights, performed in the Seville Metropolitan Area in Andalusia (Spain), was used for testing. Results show that wind estimation and predictions can be calculated at 1 Hz and a wind map can be updated at 0.4 Hz . Predictions show a convergence time with a 95% confidence interval of approximately 30 s .

Turbulent Structure of a Simplified Urban Fluid Flow Studied Through Stereoscopic Particle Image Velocimetry

NASA Astrophysics Data System (ADS)

Monnier, Bruno; Goudarzi, Sepehr A.; Vinuesa, Ricardo; Wark, Candace

2018-02-01

Stereoscopic particle image velocimetry was used to provide a three-dimensional characterization of the flow around a simplified urban model defined by a 5 by 7 array of blocks, forming four parallel streets, perpendicular to the incoming wind direction corresponding to a zero angle of incidence. Channeling of the flow through the array under consideration was observed, and its effect increased as the incoming wind direction, or angle of incidence ( AOI), was changed from 0° to 15°, 30°, and 45°. The flow between blocks can be divided into two regions: a region of low turbulence kinetic energy (TKE) levels close to the leeward side of the upstream block, and a high TKE area close to the downstream block. The centre of the arch vortex is located in the low TKE area, and two regions of large streamwise velocity fluctuation bound the vortex in the spanwise direction. Moreover, a region of large spanwise velocity fluctuation on the downstream block is found between the vortex legs. Our results indicate that the reorientation of the arch vortex at increasing AOI is produced by the displacement of the different TKE regions and their interaction with the shear layers on the sides and top of the upstream and downstream blocks, respectively. There is also a close connection between the turbulent structure between the blocks and the wind gusts. The correlations among gust components were also studied, and it was found that in the near-wall region of the street the correlations between the streamwise and spanwise gusts R_{uv} were dominant for all four AOI cases. At higher wall-normal positions in the array, the R_{uw} correlation decreased with increasing AOI, whereas the R_{uv} coefficient increased as AOI increased, and at {it{AOI}}=45° all three correlations exhibited relatively high values of around 0.4.

Aerostructural optimization of a morphing wing for airborne wind energy applications

NASA Astrophysics Data System (ADS)

Fasel, U.; Keidel, D.; Molinari, G.; Ermanni, P.

2017-09-01

Airborne wind energy (AWE) vehicles maximize energy production by constantly operating at extreme wing loading, permitted by high flight speeds. Additionally, the wide range of wind speeds and the presence of flow inhomogeneities and gusts create a complex and demanding flight environment for AWE systems. Adaptation to different flow conditions is normally achieved by conventional wing control surfaces and, in case of ground generator-based systems, by varying the reel-out speed. These control degrees of freedom enable to remain within the operational envelope, but cause significant penalties in terms of energy output. A significantly greater adaptability is offered by shape-morphing wings, which have the potential to achieve optimal performance at different flight conditions by tailoring their airfoil shape and lift distribution at different levels along the wingspan. Hence, the application of compliant structures for AWE wings is very promising. Furthermore, active gust load alleviation can be achieved through morphing, which leads to a lower weight and an expanded flight envelope, thus increasing the power production of the AWE system. This work presents a procedure to concurrently optimize the aerodynamic shape, compliant structure, and composite layup of a morphing wing for AWE applications. The morphing concept is based on distributed compliance ribs, actuated by electromechanical linear actuators, guiding the deformation of the flexible—yet load-carrying—composite skin. The goal of the aerostructural optimization is formulated as a high-level requirement, namely to maximize the average annual power production per wing area of an AWE system by tailoring the shape of the wing, and to extend the flight envelope of the wing by actively alleviating gust loads. The results of the concurrent multidisciplinary optimization show a 50.7% increase of extracted power with respect to a sequentially optimized design, highlighting the benefits of morphing and the potential of the proposed approach.

Extreme pressure differences at 0900 NZST and winds across New Zealand

NASA Astrophysics Data System (ADS)

Salinger, M. James; Griffiths, Georgina M.; Gosai, Ashmita

2005-07-01

Trends in extremes in station daily sea-level pressure differences at 0900 NZST are examined, and extreme daily wind gusts, across New Zealand, since the 1960s. Annual time series were examined (with indices of magnitude and frequency over threshold percentiles) from the daily indices selected. These follow from earlier indices of normalized monthly mean sea-level pressure differences between station pairs, except the daily indices are not normalized. The frequency statistics quantify the number of extreme zonal (westerly and easterly), or extreme meridional (southerly or northerly), pressure gradient events. The frequency and magnitude of extreme westerly episodes has increased slightly over New Zealand, with a significant increase in the westerly extremes to the south of New Zealand. In contrast, the magnitude and frequency of easterly extremes has decreased over New Zealand, but increased to the south, with some trends weakly significant. The frequency and magnitude of daily southerly extremes has decreased significantly in the region.Extreme daily wind gust events at key climate stations in New Zealand and at Hobart, Australia, are highly likely to be associated with an extreme daily pressure difference. The converse was less likely to hold: extreme wind gusts were not always observed on days with extreme daily pressure difference, probably due to the strong influence that topography has on localized station winds. Significant correlations exist between the frequency indices and both annual-average mean sea-level pressures around the Australasian region and annual-average sea surface temperature (SST) anomalies in the Southern Hemisphere. These correlations are generally stronger for indices of extreme westerly or extreme southerly airflows. Annual-average pressures in the Tasman Sea or Southern Ocean are highly correlated to zonal indices (frequency of extreme westerlies). SST anomalies in the NINO3 region or on either side of the South Island are significantly correlated with the frequency of extreme westerly airflows.

Comparison of Tropical and Extratropical Gust Factors Using Observed and Simulated Data

NASA Astrophysics Data System (ADS)

Edwards, R. P.; Schroeder, J. L.

2011-12-01

Questions of whether differences exist between tropical cyclone (TC) and extratropical (ET) wind have been the subject of considerable debate. This study will focus on the behavior of the gust factor (GF), the ratio of a peak wind speed of a certain duration and a mean wind speed of a certain duration, for three types of data: TC, ET, and simulated. For this project, the Universal Spectrum, a normalized, averaged spectrum for wind, was un-normalized and used to create simulated wind speed time series at a variety of wind speeds. Additional time series were created after modifying the spectrum to simulate the additional low-frequency energy observed in the TC wind spectrum as well as the reduction of high-frequency energy caused by a mechanical anemometer. The T and ET data used for this study were collected by Texas Tech University's mobile towers as part of various field efforts since 1998. Before comparisons were made, the database was divided into four roughness regimes based on the roughness length to ensure that differences observed in the turbulence statistics are not caused by differences in upstream terrain. The mean GF for the TC data set (open roughness regime), 1.49, was slightly higher than the ET value of 1.44 (Table 1). The distributions of GFs from each data type show similarities in shape between the base-simulated and ET data sets and between the TC and modified-simulated data set (Figure 1). These similarities are expected given the spectral similarities between the TC and modified-simulated data sets, namely additional low-frequency energy relative to the ET and base-simulated data. These findings suggest that the higher amount of low-frequency energy present in the tropical wind spectrum is partially responsible for the resulting higher GF for the tropical cyclone data. However, the modest increase in GF from the base to the modified simulated data suggest that there are more factors at work.

Meteoalarm severe wind gust thresholds from uniform periods in ECA&D

NASA Astrophysics Data System (ADS)

Wijnant, I. L.

2010-09-01

The main aim of our work is to propose new thresholds for Meteoalarm severe weather warnings which are based on the local climate, specifically for the severe wind gust warnings because the variability of these thresholds is currently rather extreme and unrealistic. In order to achieve this we added validated wind data to the database of the European Climate Assessment and Database project (ECA&D) and analysed them. We also developed wind related indices for ECA&D in order to facilitate further research. Since 2007 most of the severe weather warnings issued by the National Weather Services in Europe can be found on one website: www.meteoalarm.eu. For the 30 participating countries colour codes (yellow, orange, red) are presented on a map of Europe to reflect the severity of the weather event and its possible impact. The thresholds used for these colour codes obviously depend on the type of severe weather, but should also reflect local climate (for example: identical heat waves will have a more significant impact in Sweden than in Spain). The current Meteoalarm guideline is to issue second level warnings (orange) 1-30 times a year and third level warnings (red) less than once a year (being the total number of warnings from a specific country for all of the different sorts of severe weather events in that year). There is no similar guideline for specific sorts of severe weather events and participating countries choose their own thresholds. As a result we see unrealistic differences in the frequency and thresholds of the warnings for neighbouring countries. New thresholds based on return values would reflect the local climate of each country and give a more uniform indication of the social impact. Additionally, without uniform definitions of severe weather it remains difficult to determine if severe weather in Europe is changing. ECA&D receives long series of daily data from 62 countries throughout Europe and the Mediterranean. So far we have 7 countries that provide us with wind data. Quality control and homogeneity tests are conducted on all data before analysis is carried out. For wind data the standard ECA&D homogeneity tests (SNHT, Pettitt, Buishand and Von Neuman Ratio) are performed on the wind gust factor (the ratio of the maximum daily gust to the daily average wind speed) and a relatively new test (Petrovic's ReDistribution Method) on wind direction data. For the Dutch data we compared the results of the homogeneity tests with the available meta-data. Inhomogeneous series are not corrected but the older part (before the most recent break) is excluded from further analysis.

Beyond Tree Throw: Wind, Water, Rock and the Mechanics of Tree-Driven Bedrock Physical Weathering

NASA Astrophysics Data System (ADS)

Marshall, J. A.; Anderson, R. S.; Dawson, T. E.; Dietrich, W. E.; Minear, J. T.

2017-12-01

Tree throw is often invoked as the dominant process in converting bedrock to soil and thus helping to build the Critical Zone (CZ). In addition, observations of tree roots lifting sidewalk slabs, occupying cracks, and prying slabs of rock from cliff faces have led to a general belief in the power of plant growth forces. These common observations have led to conceptual models with trees at the center of the soil genesis process. This is despite the observation that tree throw is rare in many forested settings, and a dearth of field measurements that quantify the magnitude of growth forces. While few trees blow down, every tree grows roots, inserting many tens of percent of its mass below ground. Yet we lack data quantifying the role of trees in both damaging bedrock and detaching it (and thus producing soil). By combing force measurements at the tree-bedrock interface with precipitation, solar radiation, wind speed, and wind-driven tree sway data we quantified the magnitude and frequency of tree-driven soil-production mechanisms from two contrasting climatic and lithologic regimes (Boulder and Eel Creek CZ Observatories). Preliminary data suggests that in settings with relatively thin soils, trees can damage and detach rock due to diurnal fluctuations, wind response and rainfall events. Surprisingly, our data suggests that forces from roots and trunks growing against bedrock are insufficient to pry rock apart or damage bedrock although much more work is needed in this area. The frequency, magnitude and style of wind-driven tree forces at the bedrock interface varies considerably from one to another species. This suggests that tree properties such as mass, elasticity, stiffness and branch structure determine whether trees respond to gusts big or small, move at the same frequency as large wind gusts, or are able to self-dampen near-ground sway response to extended wind forces. Our measurements of precipitation-driven and daily fluctuations in root pressures exerted on bedrock suggest that these fluctuations may impart a cyclic stress fatigue that over the lifetime of a tree could considerably weaken the enfolding rock (104 to 106 days depending on the species). Combined, our results suggest that wind-driven root torque and water uptake may be the primary mechanisms driving bedrock erosion and soil production in thin soil settings.

Evaluation of active control technology for short haul aircraft. [cost effectiveness

NASA Technical Reports Server (NTRS)

Renshaw, J. H.; Bennett, J. A.; Harris, O. C.; Honrath, J. F.; Patterson, R. W.

1975-01-01

An evaluation of the economics of short-haul aircraft designed with active controls technology and low wing-loading to achieve short field performance with good ride quality is presented. Results indicate that for such a system incorporating gust load alleviation and augmented stability the direct operating cost is better than for aircraft without active controls.

49 CFR 325.35 - Ambient conditions; highway operations.

Code of Federal Regulations, 2012 CFR

2012-10-01

... test site at the time of testing. (b) Wind. The wind velocity at the test shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

49 CFR 325.55 - Ambient conditions; stationary test.

Code of Federal Regulations, 2012 CFR

2012-10-01

... site at the time of testing. (b) Wind. The wind velocity at the test site shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

Development of a rotor wake-vortex model, volume 1

NASA Technical Reports Server (NTRS)

Majjigi, R. K.; Gliebe, P. R.

1984-01-01

Certain empirical rotor wake and turbulence relationships were developed using existing low speed rotor wave data. A tip vortex model was developed by replacing the annulus wall with a row of image vortices. An axisymmetric turbulence spectrum model, developed in the context of rotor inflow turbulence, was adapted to predicting the turbulence spectrum of the stator gust upwash.

A summary of atmospheric turbulence measurements with specially-equipped aircraft in the US

NASA Technical Reports Server (NTRS)

Murrow, H. N.

1987-01-01

The technique of measurement of atmospheric turbulence in the form of true gust velocity is summarized. Specific aspects pointed out are related to NASA programs conducted over the last 15 years. Liberal use is made of references for details. Some recommendations resulting from a Spring 1986 workshop on atmospheric turbulence are also presented.

49 CFR 325.35 - Ambient conditions; highway operations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... test site at the time of testing. (b) Wind. The wind velocity at the test shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

49 CFR 325.55 - Ambient conditions; stationary test.

Code of Federal Regulations, 2011 CFR

2011-10-01

... site at the time of testing. (b) Wind. The wind velocity at the test site shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

49 CFR 325.55 - Ambient conditions; stationary test.

Code of Federal Regulations, 2010 CFR

2010-10-01

... site at the time of testing. (b) Wind. The wind velocity at the test site shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

49 CFR 325.35 - Ambient conditions; highway operations.

Code of Federal Regulations, 2010 CFR

2010-10-01

... test site at the time of testing. (b) Wind. The wind velocity at the test shall be measured at the... established that the wind velocity is essentially constant. Once this fact has been established, wind velocity... wind velocity is 12 mph (19.3 kph) or less. Gust wind measurements of up to 20 mph (33.2 kph) are...

A wrinkle in flight: the role of elastin fibres in the mechanical behaviour of bat wing membranes

PubMed Central

Cheney, Jorn A.; Konow, Nicolai; Bearnot, Andrew; Swartz, Sharon M.

2015-01-01

Bats fly using a thin wing membrane composed of compliant, anisotropic skin. Wing membrane skin deforms dramatically as bats fly, and its three-dimensional configurations depend, in large part, on the mechanical behaviour of the tissue. Large, macroscopic elastin fibres are an unusual mechanical element found in the skin of bat wings. We characterize the fibre orientation and demonstrate that elastin fibres are responsible for the distinctive wrinkles in the surrounding membrane matrix. Uniaxial mechanical testing of the wing membrane, both parallel and perpendicular to elastin fibres, is used to distinguish the contribution of elastin and the surrounding matrix to the overall membrane mechanical behaviour. We find that the matrix is isotropic within the plane of the membrane and responsible for bearing load at high stress; elastin fibres are responsible for membrane anisotropy and only contribute substantially to load bearing at very low stress. The architecture of elastin fibres provides the extreme extensibility and self-folding/self-packing of the wing membrane skin. We relate these findings to flight with membrane wings and discuss the aeromechanical significance of elastin fibre pre-stress, membrane excess length, and how these parameters may aid bats in resisting gusts and preventing membrane flutter. PMID:25833238

A wrinkle in flight: the role of elastin fibres in the mechanical behaviour of bat wing membranes.

PubMed

Cheney, Jorn A; Konow, Nicolai; Bearnot, Andrew; Swartz, Sharon M

2015-05-06

Bats fly using a thin wing membrane composed of compliant, anisotropic skin. Wing membrane skin deforms dramatically as bats fly, and its three-dimensional configurations depend, in large part, on the mechanical behaviour of the tissue. Large, macroscopic elastin fibres are an unusual mechanical element found in the skin of bat wings. We characterize the fibre orientation and demonstrate that elastin fibres are responsible for the distinctive wrinkles in the surrounding membrane matrix. Uniaxial mechanical testing of the wing membrane, both parallel and perpendicular to elastin fibres, is used to distinguish the contribution of elastin and the surrounding matrix to the overall membrane mechanical behaviour. We find that the matrix is isotropic within the plane of the membrane and responsible for bearing load at high stress; elastin fibres are responsible for membrane anisotropy and only contribute substantially to load bearing at very low stress. The architecture of elastin fibres provides the extreme extensibility and self-folding/self-packing of the wing membrane skin. We relate these findings to flight with membrane wings and discuss the aeromechanical significance of elastin fibre pre-stress, membrane excess length, and how these parameters may aid bats in resisting gusts and preventing membrane flutter. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Drugs in the Workplace: Research and Evaluation Data. Volume II. Research Monograph 100.

ERIC Educational Resources Information Center

Gust, Steven W., Ed.; And Others

This monograph presents 14 articles on the topics of the nature and extent of drug use by the workforce; drug use and job performance indicators; and drug free workplace program research. These articles are included: (1) Research on Drugs and the Workplace: Introduction and Summary (Steven Gust, Dennis Crouch, J. Michael Walsh); (2) Drug Use…

Active controls for flutter suppression and gust alleviation in supersonic aircraft. [YF-17 flutter model

NASA Technical Reports Server (NTRS)

Nissim, E.

1980-01-01

Results of work done on active controls on the modified YF-17 flutter model are summarized. The basic derivation of a suitable control law is discussed. It is shown that discrepencies found between analysis and wind tunnel tests originate from the lack of proper implementation of the desired control law. Program capabilities are described.

Eastern Wind Data Set | Grid Modernization | NREL

Science.gov Websites

cell was computed by combining these data sets with a composite turbine power curve. Wind power plants wind speed at the site. Adjustments were made for model biases, wake losses, wind gusts, turbine and conversion was also updated to better reflect future wind turbine technology. The 12-hour discontinuity was

Multi-Disciplinary Computational Aerodynamics

DTIC Science & Technology

2016-01-01

engineering applications including retreating blades of helicopter rotors in forward flight, maneuvering aircraft and wind turbines . It is also important in...retreating blades of helicopter rotors in forward flight, maneuvering aircraft and wind turbines . It is also important in severe wing-gust encounters where...engineering applications including retreating blades of helicopter rotors in forward flight, maneuvering aircraft and wind turbines . It is also important in

The Maneuverable Atmospheric Probe (MAP), a Remotely Piloted Vehicle.

DTIC Science & Technology

1982-05-01

9 lb. MAP vehicle and major- components .................................... 10 2. Endevco Pitot tube airspeed indicator mounted below front...28 8. Cascaded PIXE impactors, housing cylinder and wing pod front end cup with aerosol inlet plastic tubing ........................... 30 9...turbulence sensors, a Pitot tube , two air temperature sensors, and a yaw gust probe. Located at each wing tip are sensors that contain encapsulated

Applying Aerodynamics Inspired Organizational Dynamic Fit Model Disaster Relief Endeavors

DTIC Science & Technology

2010-12-01

gusts, and a dynamically stable organization returns quickly to its intended profit level, for instance, after deviation by changed consumer preferences . Hence...dynamic stability limits the level, for instance, by changed consumer preferences . Hence static stability limits initial performance... consumer preferences Maneuverability Quickness of a controlled system’s planned change from one trajectory to another Quickness of planned

Wind velocity-change (gust rise) criteria for wind turbine design

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cliff, W.C.; Fichtl, G.H.

1978-07-01

A closed-form equation is derived for root mean square (rms) value of velocity change (gust rise) that occurs over the swept area of wind turbine rotor systems and an equation for rms value of velocity change that occurs at a single point in space. These formulas confirm the intuitive assumption that a large system will encounter a less severe environment than a small system when both are placed at the same location. Assuming a normal probability density function for the velocity differences, an equation is given for calculating the expected number of velocity differences that will occur in 1 hrmore » and will be larger than an arbitrary value. A formula is presented that gives the expected number of velocity differences larger than an arbitrary value that will be encountered during the design life of a wind turbine. In addition, a method for calculating the largest velocity difference expected during the life of a turbine and a formula for estimating the risk of exceeding a given velocity difference during the life of the structure are given. The equations presented are based upon general atmospheric boundary-layer conditions and do not include information regarding events such as tornados, hurricanes, etc.« less

The gust-mitigating potential of flapping wings.

PubMed

Fisher, Alex; Ravi, Sridhar; Watkins, Simon; Watmuff, Jon; Wang, Chun; Liu, Hao; Petersen, Phred

2016-08-02

Nature's flapping-wing flyers are adept at negotiating highly turbulent flows across a wide range of scales. This is in part due to their ability to quickly detect and counterract disturbances to their flight path, but may also be assisted by an inherent aerodynamic property of flapping wings. In this study, we subject a mechanical flapping wing to replicated atmospheric turbulence across a range of flapping frequencies and turbulence intensities. By means of flow visualization and surface pressure measurements, we determine the salient effects of large-scale freestream turbulence on the flow field, and on the phase-average and fluctuating components of pressure and lift. It is shown that at lower flapping frequencies, turbulence dominates the instantaneous flow field, and the random fluctuating component of lift contributes significantly to the total lift. At higher flapping frequencies, kinematic forcing begins to dominate and the flow field becomes more consistent from cycle to cycle. Turbulence still modulates the flapping-induced flow field, as evidenced in particular by a variation in the timing and extent of leading edge vortex formation during the early downstroke. The random fluctuating component of lift contributes less to the total lift at these frequencies, providing evidence that flapping wings do indeed provide some inherent gust mitigation.

Two cold-season derechoes in Europe

NASA Astrophysics Data System (ADS)

Gatzen, Christoph; Púčik, Tomas; Ryva, David

2011-06-01

In this study, we apply for the first time the definition of a derecho (Johns and Hirt, 1987) to European cold-season convective storm systems. These occurred on 18 January 2007 and 1 March 2008, respectively, and they are shown to fulfill the criteria of a derecho. Damaging winds were reported over a distance of 1500 km and locally reached F3 intensity. Synoptic analysis for the events reveal strongly forced situations that have been described for cold-season derechoes in the United States. A comparison of swaths of damaging winds, radar structures, detected lightning, cold pool development, and cloud-top temperatures indicates that both derechoes formed along cold fronts that were affected by strong quasi-geostrophic forcing. It seems that the overlap of the cold front position with the strong differential cyclonic vorticity advection at the cyclonic flank of mid-level jet streaks favoured intense convection and high winds. The movement and path width of the two derechoes seemed to be related to this overlap. The wind gust intensity that was also different for both events is discussed and could be related to the component of the mid-level winds perpendicular to the gust fronts.

Fly-by-feel aeroservoelasticity

NASA Astrophysics Data System (ADS)

Suryakumar, Vishvas Samuel

Recent experiments have suggested a strong correlation between local flow features on the airfoil surface such as the leading edge stagnation point (LESP), transition or the flow separation point with global integrated quantities such as aerodynamic lift. "Fly-By-Feel" refers to a physics-based sensing and control framework where local flow features are tracked in real-time to determine aerodynamic loads. This formulation offers possibilities for the development of robust, low-order flight control architectures. An essential contribution towards this objective is the theoretical development showing the direct relationship of the LESP with circulation for small-amplitude, unsteady, airfoil maneuvers. The theory is validated through numerical simulations and wind tunnel tests. With the availability of an aerodynamic observable, a low-order, energy-based control formulation is derived for aeroelastic stabilization and gust load alleviation. The sensing and control framework is implemented on the Nonlinear Aeroelastic Test Apparatus at Texas A&M University. The LESP is located using hot-film sensors distributed around the wing leading edge. Stabilization of limit cycle oscillations exhibited by a nonlinear wing section is demonstrated in the presence of gusts. Aeroelastic stabilization is also demonstrated on a flying wing configuration exhibiting body freedom flutter through numerical simulations.

Flow separation on flapping and rotating profiles with spanwise gradients.

PubMed

Wong, J G; laBastide, B P; Rival, D E

2017-02-15

The growth of leading-edge vortices (LEV) on analogous flapping and rotating profiles has been investigated experimentally. Three time-varying cases were considered: a two-dimensional reference case with a spanwise-uniform angle-of-attack variation α; a case with increasing α towards the profile tip (similar to flapping flyers); and a case with increasing α towards the profile root (similar to rotor blades experiencing an axial gust). It has been shown that the time-varying spanwise angle-of-attack gradient produces a vorticity gradient, which, in combination with spanwise flow, results in a redistribution of circulation along the profile. Specifically, when replicating the angle-of-attack gradient characteristic of a rotor experiencing an axial gust, the spanwise-vorticity gradient is aligned such that circulation increases within the measurement domain. This in turn increases the local LEV growth rate, which is suggestive of force augmentation on the blade. Reversing the relative alignment of the spanwise-vorticity gradient and spanwise flow, thereby replicating that arrangement found in a flapping flyer, was found to reduce local circulation. From this, we can conclude that spanwise flow can be arranged to vary LEV growth to prolong lift augmentation and reduce the unsteadiness of cyclic loads.

Analysis of Change in the Wind Speed Ratio according to Apartment Layout and Solutions

PubMed Central

Hyung, Won-gil; Kim, Young-Moon; You, Ki-Pyo

2014-01-01

Apartment complexes in various forms are built in downtown areas. The arrangement of an apartment complex has great influence on the wind flow inside it. There are issues of residents' walking due to gust occurrence within apartment complexes, problems with pollutant emission due to airflow congestion, and heat island and cool island phenomena in apartment complexes. Currently, the forms of internal arrangements of apartment complexes are divided into the flat type and the tower type. In the present study, a wind tunnel experiment and computational fluid dynamics (CFD) simulation were performed with respect to internal wind flows in different apartment arrangement forms. Findings of the wind tunnel experiment showed that the internal form and arrangement of an apartment complex had significant influence on its internal airflow. The wind velocity of the buildings increased by 80% at maximum due to the proximity effects between the buildings. The CFD simulation for relaxing such wind flows indicated that the wind velocity reduced by 40% or more at maximum when the paths between the lateral sides of the buildings were extended. PMID:24688430

Analysis of change in the wind speed ratio according to apartment layout and solutions.

PubMed

Hyung, Won-gil; Kim, Young-Moon; You, Ki-Pyo

2014-01-01

Apartment complexes in various forms are built in downtown areas. The arrangement of an apartment complex has great influence on the wind flow inside it. There are issues of residents' walking due to gust occurrence within apartment complexes, problems with pollutant emission due to airflow congestion, and heat island and cool island phenomena in apartment complexes. Currently, the forms of internal arrangements of apartment complexes are divided into the flat type and the tower type. In the present study, a wind tunnel experiment and computational fluid dynamics (CFD) simulation were performed with respect to internal wind flows in different apartment arrangement forms. Findings of the wind tunnel experiment showed that the internal form and arrangement of an apartment complex had significant influence on its internal airflow. The wind velocity of the buildings increased by 80% at maximum due to the proximity effects between the buildings. The CFD simulation for relaxing such wind flows indicated that the wind velocity reduced by 40% or more at maximum when the paths between the lateral sides of the buildings were extended.

A review of research in rotor loads

NASA Technical Reports Server (NTRS)

Bousman, William G.; Mantay, Wayne R.

1988-01-01

The research accomplished in the area of rotor loads over the last 13 to 14 years is reviewed. The start of the period examined is defined by the 1973 AGARD Milan conference and the 1974 hypothetical rotor comparison. The major emphasis of the review is research performed by the U.S. Army and NASA at their laboratories and/or by the industry under government contract. For the purpose of this review, two main topics are addressed: rotor loads prediction and means of rotor loads reduction. A limited discussion of research in gust loads and maneuver loads is included. In the area of rotor loads predictions, the major problem areas are reviewed including dynamic stall, wake induced flows, blade tip effects, fuselage induced effects, blade structural modeling, hub impedance, and solution methods. It is concluded that the capability to predict rotor loads has not significantly improved in this time frame. Future progress will require more extensive correlation of measurements and predictions to better understand the causes of the problems, and a recognition that differences between theory and measurement have multiple sources, yet must be treated as a whole. There is a need for high-quality data to support future research in rotor loads, but the resulting data base must not be seen as an end in itself. It will be useful only if it is integrated into firm long-range plans for the use of the data.

Wind and Wake Sensing with UAV Formation Flight: System Development and Flight Testing

NASA Astrophysics Data System (ADS)

Larrabee, Trenton Jameson

Wind turbulence including atmospheric turbulence and wake turbulence have been widely investigated; however, only recently it become possible to use Unmanned Aerial Vehicles (UAVs) as a validation tool for research in this area. Wind can be a major contributing factor of adverse weather for aircraft. More importantly, it is an even greater risk towards UAVs because of their small size and weight. Being able to estimate wind fields and gusts can potentially provide substantial benefits for both unmanned and manned aviation. Possible applications include gust suppression for improving handling qualities, a better warning system for high wind encounters, and enhanced control for small UAVs during flight. On the other hand, the existence of wind can be advantageous since it can lead to fuel savings and longer duration flights through dynamic soaring or thermal soaring. Wakes are an effect of the lift distribution across an aircraft's wing or tail. Wakes can cause substantial disturbances when multiple aircraft are moving through the same airspace. In fact, the perils from an aircraft flying through the wake of another aircraft is a leading cause of the delay between takeoff times at airports. Similar to wind, though, wakes can be useful for energy harvesting and increasing an aircraft's endurance when flying in formation which can be a great advantage to UAVs because they are often limited in flight time due to small payload capacity. Formation flight can most often be seen in manned aircraft but can be adopted for use with unmanned systems. Autonomous flight is needed for flying in the "sweet spot" of the generated wakes for energy harvesting as well as for thermal soaring during long duration flights. For the research presented here formation flight was implemented for the study of wake sensing and gust alleviation. The major contributions of this research are in the areas of a novel technique to estimate wind using an Unscented Kalman filter and experimental wake sensing data using UAVs in formation flight. This has been achieved and well documented before in manned aircraft but very little work has been done on UAV wake sensing especially during flight testing. This document describes the development and flight testing of small unmanned aerial system (UAS) for wind and wake sensing purpose including a Ground Control Station (GCS) and UAVs. This research can be stated in four major components. Firstly, formation flight was obtained by integrating a formation flight controller on the WVU Phastball Research UAV aircraft platform from the Flight Control Systems Laboratory (FCSL) at West Virginia University (WVU). Second, a new approach to wind estimation using an Unscented Kalman filter (UKF) is discussed along with results from flight data. Third, wake modeling within a simulator and wake sensing during formation flight is shown. Finally, experimental results are used to discuss the "sweet spot" for energy harvesting in formation flight, a novel approach to cooperative wind estimation, and gust suppression control for a follower aircraft in formation flight.

Riding and handling qualities of light aircraft: A review and analysis

NASA Technical Reports Server (NTRS)

Smetana, F. O.; Summery, D. C.; Johnson, W. D.

1972-01-01

Design procedures and supporting data necessary for configuring light aircraft to obtain desired responses to pilot commands and gusts are presented. The procedures employ specializations of modern military and jet transport practice where these provide an improvement over earlier practice. General criteria for riding and handling qualities are discussed in terms of the airframe dynamics. Methods available in the literature for calculating the coefficients required for a linearized analysis of the airframe dynamics are reviewed in detail. The review also treats the relation of spin and stall to airframe geometry. Root locus analysis is used to indicate the sensitivity of airframe dynamics to variations in individual stability derivatives and to variations in geometric parameters. Computer programs are given for finding the frequencies, damping ratios, and time constants of all rigid body modes and for generating time histories of aircraft motions in response to control inputs. Appendices are included presenting the derivation of the linearized equations of motion; the stability derivatives; the transfer functions; approximate solutions for the frequency, damping ratio, and time constants; an indication of methods to be used when linear analysis is inadequate; sample calculations; and an explanation of the use of root locus diagrams and Bode plots.

Dynamic Response of an Energy Harvesting Device Under Realistic Flow Conditions

NASA Astrophysics Data System (ADS)

O'Connor, Joseph; Revell, Alistair

2017-11-01

The need for reliable, cost-efficient, green energy alternatives has led to increased research in the area of energy harvesting. One approach to energy harvesting is to take advantage of self-sustaining flow-induced vibrations. Through the use of a piezoelectric flag, the mechanical strain from the flapping motion can be converted into electrical energy. While such devices show a lot of promise, the fluid-structure-electrical interactions are highly nonlinear and their response to off-design variations in flow conditions, such as those likely to be encountered upon deployment, is relatively unexplored. The purpose of the present work is to examine how a representative energy harvesting device performs in realistic atmospheric flow conditions involving wind gusts with spatial and temporal variations. A recently developed lattice-Boltzmann-immersed boundary-finite element model is used to perform fully-coupled 3D simulations of the fluid-structure system. For a range of unsteady flow conditions the resulting flow features and structural motion are examined and key behaviour modes are mapped out. The findings of this work will be particularly relevant for self-powered remote sensing networks, which often require deployment in unpredictable and varied environments.

Face Sheet/Core Disbond Growth in Honeycomb Sandwich Panels Subjected to Ground-Air-Ground Pressurization and In-Plane Loading

NASA Technical Reports Server (NTRS)

Chen, Zhi M.; Krueger, Ronald; Rinker, Martin

2015-01-01

Typical damage modes in light honeycomb sandwich structures include face sheet/core disbonding and core fracture, both of which can pose a threat to the structural integrity of a component. These damage modes are of particular interest to aviation certification authorities since several in-service occurrences, such as rudder structural failure and other control surface malfunctions, have been attributed to face sheet/core disbonding. Extensive studies have shown that face sheet/core disbonding and core fracture can lead to damage propagation caused by internal pressure changes in the core. The increasing use of composite sandwich construction in aircraft applications makes it vitally important to understand the effect of ground-air-ground (GAG) cycles and conditions such as maneuver and gust loads on face sheet/core disbonding. The objective of the present study was to use a fracture mechanics based approach developed earlier to evaluate the loading at the disbond front caused by ground-air-ground pressurization and in-plane loading. A honeycomb sandwich panel containing a circular disbond at one face sheet/core interface was modeled with three-dimensional (3D) solid finite elements. The disbond was modeled as a discrete discontinuity and the strain energy release rate along the disbond front was computed using the Virtual Crack Closure Technique (VCCT). Special attention was paid to the pressure-deformation coupling which can decrease the pressure load within the disbonded sandwich section significantly when the structure is highly deformed. The commercial finite element analysis software, Abaqus/Standard, was used for the analyses. The recursive pressure-deformation coupling problem was solved by representing the entrapped air in the honeycomb cells as filled cavities in Abaqus/Standard. The results show that disbond size, face sheet thickness and core thickness are important parameters that determine crack tip loading at the disbond front. Further, the pressure-deformation coupling was found to have an important load decreasing effect [6]. In this paper, a detailed problem description is provided first. Second, the analysis methodology is presented. The fracture mechanics approach used is described and the specifics of the finite element model, including the fluid-filled cavities, are introduced. Third, the initial model verification and validation are discussed. Fourth, the findings from a closely related earlier study [6] are summarized. These findings provided the basis for the current investigation. Fifth, an aircraft ascent scenario from 0 to 12192 m (0 to 40000 ft) is considered and the resulting crack tip loading at the disbond front is determined. In-plane loading to simulate maneuvers and gust conditions are also considered. Sixth, the results are shown for a curved panel, which was used to simulate potential fuselage applications. Finally, a brief summary of observations is presented and recommendations for improvement are provided.

Analytic models of ducted turbomachinery tone noise sources. Volume 1: Analysis

NASA Technical Reports Server (NTRS)

Clark, T. L.; Ganz, U. W.; Graf, G. A.; Westall, J. S.

1974-01-01

The analytic models developed for computing the periodic sound pressure of subsonic fans and compressors in an infinite, hardwall annular duct with uniform flow are described. The basic sound-generating mechanism is the scattering into sound waves of velocity disturbances appearing to the rotor or stator blades as a series of harmonic gusts. The models include component interactions and rotor alone.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-09-04

ISS017-E-015166 (4 Sept. 2008) --- Hurricane Ike was still a Category 4 storm on the morning of Sept. 4 when this photo was taken from the International Space Station's vantage point of 220 miles above the Earth. The season's ninth named storm was churning west-northwestward through the mid-Atlantic Ocean sporting winds of 120 nautical miles per hour with gusts to 145.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-09-04

ISS017-E-015170 (4 Sept. 2008) --- Hurricane Ike was still a Category 4 storm on the morning of Sept. 4 when this photo was taken from the International Space Station's vantage point of 220 miles above the Earth. The season's ninth named storm was churning west-northwestward through the mid-Atlantic Ocean sporting winds of 120 nautical miles per hour with gusts to 145.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-09-04

ISS017-E-015163 (4 Sept. 2008) --- Hurricane Ike was still a Category 4 storm on the morning of Sept. 4 when this photo was taken from the International Space Station's vantage point of 220 miles above the Earth. The season's ninth named storm was churning west-northwestward through the mid-Atlantic Ocean sporting winds of 120 nautical miles per hour with gusts to 145.

Earth Observations taken by the Expedition 17 Crew

NASA Image and Video Library

2008-09-04

ISS017-E-015162 (4 Sept. 2008) --- Hurricane Ike was still a Category 4 storm on the morning of Sept. 4 when this photo was taken from the International Space Station's vantage point of 220 miles above the Earth. The season's ninth named storm was churning west-northwestward through the mid-Atlantic Ocean sporting winds of 120 nautical miles per hour with gusts to 145.

Photogrammetric Verification of Fiber Optic Shape Sensors on Flexible Aerospace Structures

NASA Technical Reports Server (NTRS)

Moore, Jason P.; Rogge, Matthew D.; Jones, Thomas W.

2012-01-01

Multi-core fiber (MCF) optic shape sensing offers the possibility of providing in-flight shape measurements of highly flexible aerospace structures and control surfaces for such purposes as gust load alleviation, flutter suppression, general flight control and structural health monitoring. Photogrammetric measurements of surface mounted MCF shape sensing cable can be used to quantify the MCF installation path and verify measurement methods.

Statistical modeling of space shuttle environmental data

NASA Technical Reports Server (NTRS)

Tubbs, J. D.; Brewer, D. W.

1983-01-01

Statistical models which use a class of bivariate gamma distribution are examined. Topics discussed include: (1) the ratio of positively correlated gamma varieties; (2) a method to determine if unequal shape parameters are necessary in bivariate gamma distribution; (3) differential equations for modal location of a family of bivariate gamma distribution; and (4) analysis of some wind gust data using the analytical results developed for modeling application.

Designing Inter-Organisational Collectivities for Dynamic Fit: Stability, maneuvrability and Application in Disaster Relief Endeavours

DTIC Science & Technology

2011-01-01

changed consumer preferences . Hence, static stability limits initial performance deviation (e.g., maintaining desired airplane altitude, maintaining...by changed consumer preferences . Hence, dynamic stability limits the duration of performance deviation (e.g., maintaining desired airplane altitude...altitude from wind gust. Initial resistance to deviation in profit level from change in consumer preferences . Dynamic stability Quickness of a

Some extemporaneous comments on our experiences with towers for wind generators

NASA Technical Reports Server (NTRS)

Hutter, U.

1973-01-01

A wind generator tower must be designed to withstand fatigue forces and gust winds loads. Optimum tower height depends on the energy cost to the customer because an increase in height results in an increase in the cost of the plant. It is suggested that costs are minimum for the shortest tower possible and that the rotor should be as large as possible.

Generating Excitement: Build Your Own Generator to Study the Transfer of Energy

ERIC Educational Resources Information Center

Fletcher, Kurt; Rommel-Esham, Katie; Farthing, Dori; Sheldon, Amy

2011-01-01

The transfer of energy from one form to another can be difficult to understand. The electrical energy that turns on a lamp may come from the burning of coal, water falling at a hydroelectric plant, nuclear reactions, or gusts of wind caused by the uneven heating of the Earth. The authors have developed and tested an exciting hands-on activity to…

Modelling derecho dynamics and the direct radiative effect of wildfire smoke upon it with NWP model HARMONIE

NASA Astrophysics Data System (ADS)

Toll, Velle; Männik, Aarne

2014-05-01

Convection permitting numerical weather prediction model HARMONIE was used to simulate the dynamics of the derecho that swept over Eastern Europe on August 8, 2010. The storm moved over Belarus, Lithuania, Latvia, Estonia and Finland and the strongest wind gusts (up to 36.5 m/s) were measured in Estonia. The storm path is recorded on the radar images where characteristic bow echo was observed. The model setup was similar to near-future operational, nearly kilometre-scale environments in European national weather services. Hindcast experiments show the ability of the HARMONIE model to predict the severe convective storm and forecast concurrent strong wind gusts. Wind gusts with very similar intensity to observed ones were simulated by the HARMONIE model and 2.5-km horizontal resolution appears sufficient for reliable forecast of the derecho event. The timing of the modelled storm was in good agreement with the observations. The simulated average storm propagation speed was 25 m/s, similar to the radar observations. Hindcast experiments suggest that more precise warning for the storm could have been issued if the HARMONIE model would have been utilised. The derecho event was accompanied by the remarkable smoke aerosol concentrations (maximum total aerosol optical depth more than 4 at 550 nm) originating from the wildfires from Russia. Smoke plume travelled clockwise around Moscow from August 5 to 9. On August 8, 2010, smoke plume was situated on the Eastern border of Estonia. The derecho occurred on the western side of the smoke plume path. HARMONIE experiments were performed to study the direct radiative effect of wildfire smoke on a severe convective storm. The impact of smoke aerosol on the derecho dynamics was investigated. Reduction in the shortwave radiation flux at the surface resulting from aerosol influence simulated by the HARMONIE model is up to 200 W/m2 in the area with the highest aerosol concentrations. This causes near surface cooling of up to 3 ºC. The direct radiative effect of aerosol increases the stability of the atmospheric boundary layer and this had influence on the simulated derecho dynamics.

Driver steering dynamics measured in car simulator under a range of visibility and roadmaking conditions

NASA Technical Reports Server (NTRS)

Allen, R. W.; Mcruer, D. T.

1977-01-01

A simulation experiment was conducted to determine the effect of reduced visibility on driver lateral (steering) control. The simulator included a real car cab and a single lane road image projected on a screen six feet in front of the driver. Simulated equations of motion controlled apparent car lane position in response to driver steering actions, wind gusts, and road curvature. Six drivers experienced a range of visibility conditions at various speeds with assorted roadmaking configurations (mark and gap lengths). Driver describing functions were measured and detailed parametric model fits were determined. A pursuit model employing a road curvature feedforward was very effective in explaining driver behavior in following randomly curving roads. Sampled-data concepts were also effective in explaining the combined effects of reduced visibility and intermittent road markings on the driver's dynamic time delay. The results indicate the relative importance of various perceptual variables as the visual input to the driver's steering control process is changed.

The role of passive avian head stabilization in flapping flight

PubMed Central

Pete, Ashley E.; Kress, Daniel; Dimitrov, Marina A.; Lentink, David

2015-01-01

Birds improve vision by stabilizing head position relative to their surroundings, while their body is forced up and down during flapping flight. Stabilization is facilitated by compensatory motion of the sophisticated avian head–neck system. While relative head motion has been studied in stationary and walking birds, little is known about how birds accomplish head stabilization during flapping flight. To unravel this, we approximate the avian neck with a linear mass–spring–damper system for vertical displacements, analogous to proven head stabilization models for walking humans. We corroborate the model's dimensionless natural frequency and damping ratios from high-speed video recordings of whooper swans (Cygnus cygnus) flying over a lake. The data show that flap-induced body oscillations can be passively attenuated through the neck. We find that the passive model robustly attenuates large body oscillations, even in response to head mass and gust perturbations. Our proof of principle shows that bird-inspired drones with flapping wings could record better images with a swan-inspired passive camera suspension. PMID:26311316

Aeroservoelastic and Structural Dynamics Research on Smart Structures Conducted at NASA Langley Research Center

NASA Technical Reports Server (NTRS)

McGowan, Anna-Maria Rivas; Wilkie, W. Keats; Moses, Robert W.; Lake, Renee C.; Florance, Jennifer Pinkerton; Wieseman, Carol D.; Reaves, Mercedes C.; Taleghani, Barmac K.; Mirick, Paul H.; Wilbur, Mathew L.

1997-01-01

An overview of smart structures research currently underway at the NASA Langley Research Center in the areas of aeroservoelasticity and structural dynamics is presented. Analytical and experimental results, plans, potential technology pay-offs, and challenges are discussed. The goal of this research is to develop the enabling technologies to actively and passively control aircraft and rotorcraft vibration and loads using smart devices. These enabling technologies and related research efforts include developing experimentally-validated finite element and aeroservoelastic modeling techniques; conducting bench experimental tests to assess feasibility and understand system trade-offs; and conducting large-scale wind tunnel tests to demonstrate system performance. The key aeroservoelastic applications of this research include: active twist control of rotor blades using interdigitated electrode piezoelectric composites and active control of flutter, and gust and buffeting responses using discrete piezoelectric patches. In addition, NASA Langley is an active participant in the DARPA/Air Force Research Laboratory/NASA/Northrop Grumman Smart Wing program which is assessing aerodynamic performance benefits using smart materials.

USSR Report, Political and Sociological Affairs, No. 1443

DTIC Science & Technology

1983-08-10

300147 JPRS 84083 10 August 1983 USSR Report POLITICAL AND SOCIOLOGICAL AFFAIRS No. 1443 Fsnc QUALITY rr^ü^-j) g 19980609 108 FBIS...agency of the Soviet Union. Permission for further reproduction must be obtained from copyright owner. JPRS 84 083 10 Axt gust 1983 USSR REPORT...gorkoms must 10 improve the selection of instructors of the social disciplines and the work of raising their qualifications and strengthen control

Derivation of equations of motion for multi-blade rotors employing coupled modes and including high twist capability

NASA Technical Reports Server (NTRS)

Sopher, R.

1975-01-01

The equations of motion are derived for a multiblade rotor. A high twist capability and coupled flatwise-edgewise assumed normal modes are employed instead of uncoupled flatwise - edgewise assumed normal models. The torsion mode is uncoupled. Support system models, consisting of complete helicopters in free flight, or grounded flexible supports, arbitrary rotor-induced inflow, and arbitrary vertical gust models are also used.

Supertyphoon Yuri, Western Pacific Ocean

NASA Image and Video Library

1991-12-01

Supertyphoon Yuri began development approximately 1000 miles east of the Philippine Islands. At the time this photo was taken, Yuri was about 1000 nautical miles in diameter and had estimated maximum sustained wind speeds of 145 mph, gusting to 170 mph. This oblique view shows the well formed eye of Yuri and the raised segment of clouds at the cusp of the eye indicating very high wind speeds within the vortex.

Acta Aeronautica et Astronautica Sinica,

DTIC Science & Technology

1983-03-04

power spectrum and counting methods [1,2,3]. If the stochastic load-time mechanism (such as gusts of wind, random 38...34 "- " ° - " . . .. . . . . . . . . ’ - - - Ř vibrations, etc.), then we can use the power spectrum technique, and we can also use the counting method. However, the...simplification for treat - ment so that the differences in obtained results are very minute, and are also closest to the random spectrum. This then tells us

Firestorms

DTIC Science & Technology

1982-04-15

Morton 1957)#]. Tropical rainforests in Vietnam are characterized by prevailing relative humidity of 80%; also, dead vegetation decays so rapidly that...wind for the onset of a firestorm raises several points. Tropical cyclones form in environments in which there is little vertical wind shear to cause...of 18-19 April 1965 as a case of a fire occurring in the warm sector of an extra- tropical cyclone (winds of 8-10 m/s, with gusts of 15; airmass

Recognition and Control of Low Level Wind Shear.

DTIC Science & Technology

1985-04-01

based cumulus 71ouds; (2) "first gusts" (3) large downbursts or " macrobursts " and (4) "microbursts.ŕ The following -: "-: 2...shear hazards associated with thunderstorms - " macrobursts " and "microbursts" - are both in the form of "downbursts" from mature thunderstorms(13:78...The only real difference between large downbursts( macrobursts ), and small ones (microbursts), is their size and duration(13:78). Of all the

Tree crown condition in Virginia before and after Hurricane Isabel (September 2003)

Treesearch

KaDonna Randolph; Anita Rose

2009-01-01

In September 2003, Hurricane Isabel made landfall in North Carolina as a Category 2 hurricane. As it moved inland, with sustained wind speeds of 37 to 69 miles per hour (59 to 111 km per hour) and gusts up to 91 miles per hour (146 km per hour), the hurricane caused widespread damage throughout Virginia and is a plausible explanation for adverse changes observed in...

14 CFR 23.415 - Ground gust conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) If pilot forces less than the minimums specified in § 23.397(b) are used for design, the effects of... according to the formula: H=K c S q where— H=limit hinge moment (ft.-lbs.); c=mean chord of the control... pressure (p.s.f.) based on a design speed not less than 14.6 √(W/S) + 14.6 (f.p.s.) where W/S=wing loading...

14 CFR 23.415 - Ground gust conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) If pilot forces less than the minimums specified in § 23.397(b) are used for design, the effects of... according to the formula: H=K c S q where— H=limit hinge moment (ft.-lbs.); c=mean chord of the control... pressure (p.s.f.) based on a design speed not less than 14.6 √(W/S) + 14.6 (f.p.s.) where W/S=wing loading...

14 CFR 23.415 - Ground gust conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) If pilot forces less than the minimums specified in § 23.397(b) are used for design, the effects of... according to the formula: H=K c S q where— H=limit hinge moment (ft.-lbs.); c=mean chord of the control... pressure (p.s.f.) based on a design speed not less than 14.6 √(W/S) + 14.6 (f.p.s.) where W/S=wing loading...

The evolution of convective storms from their footprints on the sea as viewed by synthetic aperture radar from space

NASA Technical Reports Server (NTRS)

Atlas, David; Black, Peter G.

1994-01-01

SEASAT synthetic aperture radar (SAR) echoes from the sea have previously been shown to be the result of rain and winds produced by convective stroms; rain damps the surface waves and causes ech-free holes, while the diverging winds associated with downdraft generate waves and associated echoes surrounding the holes. Gust fronts are also evident. Such a snapshot from 8 July 1978 has been examined in conjunction with ground-based radar. This leads to the conclusion that the SAR storm footprints resulted from storm processes that occurred up to an hour or more prior to the snapshot. A sequence of events is discerned from the SAR imagery in which new cell growth is triggered in between the converging outflows of two preexisting cells. In turn, the new cell generates a mini-squall line along its expanding gust front. While such phenomena are well known over land, the spaceborne SAR now allows important inferences to be made about the nature and frequency of convective storms over the oceans. The storm effects on the sea have significant implications for spaceborne wind scatterometry and rainfall measurements. Some of the findings herein remain speculative because of the great distance to the Miami weather radar-the only source of corroborative data.

Aeroservoelastic Testing of a Sidewall Mounted Free Flying Wind-Tunnel Model

NASA Technical Reports Server (NTRS)

Scott, Robert C.; Vetter, Travis K.; Penning, Kevin B.; Coulson, David A.; Heeg, Jennifer

2008-01-01

A team comprised of the Air Force Research Laboratory (AFRL), Northrop Grumman, Lockheed Martin, and the NASA Langley Research Center conducted three j wind-tunnel tests in the Transonic Dynamics Tunnel to demonstrate active control technologies relevant to large, exible vehicles. In the rst of these three tests, a semispan, aeroelastically scaled, wind-tunnel model of a ying wing SensorCraft vehi- cle was mounted to a force balance to demonstrate gust load alleviation. In the second and third tests, the same wing was mated to a new, multi-degree-of-freedom, sidewall mount. This mount allowed the half-span model to translate vertically and pitch at the wing root, allowing better simulation of the full span vehicle's rigid-body modes. Gust Load Alleviation (GLA) and Body Freedom Flutter (BFF) suppression were successfully demonstrated. The rigid body degrees-of-freedom required that the model be own in the wind tunnel using an active control system. This risky mode of testing necessitated that a model arrestment system be integrated into the new mount. The safe and successful completion of these free-flying tests required the development and integration of custom hardware and software. This paper describes the many systems, software, and procedures that were developed as part of this effort.

Acute Low Back Pain? Do Not Blame the Weather-A Case-Crossover Study.

PubMed

Beilken, Keira; Hancock, Mark J; Maher, Chris G; Li, Qiang; Steffens, Daniel

2017-06-01

To investigate the influence of various weather parameters on the risk of developing a low back pain (LBP) episode. Case-crossover study. Primary care clinics in Sydney, Australia. 981 participants with a new episode of acute LBP. Weather parameters were obtained from the Australian Bureau of Meteorology. Odds ratios (OR) and 95% confidence intervals (95% CI) were derived comparing two exposure variables in the case window-(1) the average of the weather variable for the day prior to pain onset and (2) the change in the weather variable from 2 days prior to 1 day prior to pain onset-with exposures in two control windows (1 week and 1 month before the case window). The weather parameters of precipitation, humidity, wind speed, wind gust, wind direction, and air pressure were not associated with the onset of acute LBP. For one of the four analyses, higher temperature slightly increased the odds of pain onset. Common weather parameters that had been previously linked to musculoskeletal pain, such as precipitation, humidity, wind speed, wind gust, wind direction, and air pressure, do not increase the risk of onset for LBP. © 2016 American Academy of Pain Medicine. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Verification and implementation of microburst day potential index (MDPI) and wind INDEX (WINDEX) forecasting tools at Cape Canaveral Air Station

NASA Technical Reports Server (NTRS)

Wheeler, Mark

1996-01-01

This report details the research, development, utility, verification and transition on wet microburst forecasting and detection the Applied Meteorology Unit (AMU) did in support of ground and launch operations at Kennedy Space Center (KSC) and Cape Canaveral Air Station (CCAS). The unforecasted wind event on 16 August 1994 of 33.5 ms-1 (65 knots) at the Shuttle Landing Facility raised the issue of wet microburst detection and forecasting. The AMU researched and analyzed the downburst wind event and determined it was a wet microburst event. A program was developed for operational use on the Meteorological Interactive Data Display System (MIDDS) weather system to analyze, compute and display Theta(epsilon) profiles, the microburst day potential index (MDPI), and wind index (WINDEX) maximum wind gust value. Key microburst nowcasting signatures using the WSR-88D data were highlighted. Verification of the data sets indicated that the MDPI has good potential in alerting the duty forecaster to the potential of wet microburst and the WINDEX values computed from the hourly surface data do have potential in showing a trend for the maximum gust potential. WINDEX should help in filling in the temporal hole between the MDPI on the last Cape Canaveral rawinsonde and the nowcasting radar data tools.

Revisiting the synoptic-scale predictability of severe European winter storms using ECMWF ensemble reforecasts

NASA Astrophysics Data System (ADS)

Pantillon, Florian; Knippertz, Peter; Corsmeier, Ulrich

2017-10-01

New insights into the synoptic-scale predictability of 25 severe European winter storms of the 1995-2015 period are obtained using the homogeneous ensemble reforecast dataset from the European Centre for Medium-Range Weather Forecasts. The predictability of the storms is assessed with different metrics including (a) the track and intensity to investigate the storms' dynamics and (b) the Storm Severity Index to estimate the impact of the associated wind gusts. The storms are well predicted by the whole ensemble up to 2-4 days ahead. At longer lead times, the number of members predicting the observed storms decreases and the ensemble average is not clearly defined for the track and intensity. The Extreme Forecast Index and Shift of Tails are therefore computed from the deviation of the ensemble from the model climate. Based on these indices, the model has some skill in forecasting the area covered by extreme wind gusts up to 10 days, which indicates a clear potential for early warnings. However, large variability is found between the individual storms. The poor predictability of outliers appears related to their physical characteristics such as explosive intensification or small size. Longer datasets with more cases would be needed to further substantiate these points.

The development of the DAST I remotely piloted research vehicle for flight testing an active flutter suppression control system. Ph.D. Thesis. Final Report

NASA Technical Reports Server (NTRS)

Grose, D. L.

1979-01-01

The development of the DAST I (drones for aerodynamic and structural testing) remotely piloted research vehicle is described. The DAST I is a highly modified BQM-34E/F Firebee II Supersonic Aerial Target incorporating a swept supercritical wing designed to flutter within the vehicle's flight envelope. The predicted flutter and rigid body characteristics are presented. A description of the analysis and design of an active flutter suppression control system (FSS) designed to increase the flutter boundary of the DAST wing (ARW-1) by a factor of 20% is given. The design and development of the digital remotely augmented primary flight control system and on-board analog backup control system is presented. An evaluation of the near real-time flight flutter testing methods is made by comparing results of five flutter testing techniques on simulated DAST I flutter data. The development of the DAST ARW-1 state variable model used to generate time histories of simulated accelerometer responses is presented. This model uses control surface commands and a Dryden model gust as inputs. The feasibility of the concept of extracting open loop flutter characteristics from closed loop FSS responses was examined. It was shown that open loop characteristics can be determined very well from closed loop subcritical responses.

Sand dune tracking from satellite laser altimetry

NASA Astrophysics Data System (ADS)

Dabboor, Mohammed

Substantial problems arise from sand movement in arid and semi-arid countries. Sand poses a threat to infrastructure, agricultural and urban areas. These issues are caused by the encroachment of sand on roads and railway tracks, farmland, towns and villages, and airports, to name a few. Sand movement highly depends on geomorphology including vegetation cover, shape and height of the terrain, and grain size of the sand. However, wind direction and speed are the most important factors that affect efficient sand movement. The direction of the movement depends on the main direction of the wind, but it has been shown that a minimum wind speed is required, e.g. wind gusts, to initiate sand transport. This fact prevents a simple calculation of sand transport from conventional wind data as wind records rarely contain sub-minute intervals masking out any wind gusts. An alternative of predicting sand transport is the direct observation of sand advance by in situ measurements or via satellite. Until recently, satellite imagery was the only means to compare dune shape and position for predicting dune migration over several years. In 2003, the NASA laser altimetry mission ICESat became operational and monitors elevations over all surface types including sand dunes with an accuracy of about 10-20 cm. In this study, ICESat observations from repeat tracks (tracks overlapping eachother within 50 m) are used to derive sand dune advance and direction. The method employs a correlation of the elevation profiles over several dunes and was sucessfully validated with synthetic data. The accuracy of this method is 5 meters of dune advance. One of the most active areas exhibiting sand and dune movement is the area of the Arabian Peninsula. Approximately one-third of the Arabian Peninsula is covered by sand dunes. Different wind regimes (Shamal, Kaus) cause sand dune movement in the selected study area in the eastern part of the Arabian Peninsula between 20-25 degrees North and 45-55 degrees East. Two different dune types can be distinguised which exhibit a 6 m and 26 m average dune advance over a 6 months time period. Wind speed/direction data and the observed dune advance agree well and indicate that dune tracking from space is a viable alternative to in situ or model data.