Sanitation of chicken eggs by ionizing radiation: functional and nutritional assessment

NASA Astrophysics Data System (ADS)

Pinto, P.; Ribeiro, R.; Sousa, L.; Verde, S. Cabo; Lima, M. G.; Dinis, M.; Santana, A.; Botelho, M. L.

2004-09-01

Alternative technologies must be developed and implemented considering sanitation and preservation of eggs mainly for risk population. Food irradiation is an alternative to free Salmonella spp. and Campylobacter spp. eggs, as a low dose point to a safety assurance. This study presents the correlation between irradiation doses (0.5 kGy up to 5 kGy at dose rate of 1.0 kGy/h) and some of functional and nutritional egg properties. Viscosimetry of non-irradiated and irradiated eggs was evaluated by means of VT550 Haake with an NV sensor and co-axes cylinders. After irradiation at 5 kGy, the yolk colour die (pale yellow) and the white egg was modified to a turbid yellow. The Cross equation was utilized to viscosimetry curves. Based on the assymptotics viscosimetry data indicated that increase of doses corresponds to an increase of the yolk and a decrease of white egg viscosimetry as such a Newton behaviour. Irradiation effects on nutritional properties were evaluated by means of egg protein patterns that were assessed by polyacrylamide gel electrophoresis. Lipids were identified by TLC. Based on results the sanitation dose is lower than the limit dose for the decrease of the main eggs properties.

Effect of coupling agent on durian skin fibre nanocomposite reinforced polypropylene

NASA Astrophysics Data System (ADS)

Siti Nur E'zzati, M. A.; Anuar, H.; Siti Munirah Salimah, A. R.

2018-01-01

This paper reports on the development of a composite-based natural fiber to reduce the reliance on petroleum-based product in order to amplify environmental awareness. The production of Durian Skin Nanofiber (DSNF) was conducted using biological fermentation method via rhizopus oryzae in order to obtain the nano dimension of the particle size. Polypropylene (PP) and DSNF were produced using Haake internal mixer via melt blending technique. The significant effect of maleic anhydride grafted polypropylene (MAPP) on the properties of PP/DSNF nanocomposite was investigated to study its mechanical properties which are tensile strength and thermal stability using thermogravimetric (TGA) and differential scanning analysis (DSC). The tensile property of PP nanocomposites increased from 33 MPa to 38 MPa with the presence of MAPP. The addition of MAPP also increased the thermal stability of PP/DSNF nanocomposite where the char residue increased by 52%. Besides that, the thermal degradation of PP/DSNF and PP/DSNF-MAPP were higher than PP where they exerted higher amount of weight loss at an elevated temperature. The percentage of crystallinity, %Xc, of PP nanocomposites improved with the addition of MAPP by 35% based on the differential scanning calorimetry (DSC) result. The SEM analysis showed that the PP/DSNF-MAPP exerts ductile fracture while PP/DSNF exerts brittle fracture.

Effect of fibre treatments on tensile properties of ethylene vinyl acetate/natural rubber/mengkuang leaf fibre (EVA/NR/MLF) thermoplastic elastomer composites

NASA Astrophysics Data System (ADS)

Hashim, Faiezah; Ismail, Hanafi; Rusli, Arjulizan

2017-07-01

Nowadays, a great attention has been dedicated to natural fibers as reinforcement for polymer composites. Natural fibers, compared to glass fibers, exhibit better mechanical properties, such as stiffness, impact strength, flexibility and modulus. However, certain drawbacks, such as the incompatibility between fibers and polymer matrices, the tendency to form aggregates during processing and the poor resistance to moisture, reduce the use of these natural fibers as reinforcements in polymers. Several treatments and modifications are being used to improve the adhesion between fibre and matrix. In this work, the effect of bleaching treatments using hydrogen peroxide in the Mengkuang leaf fibre (MLF) was evaluated on tensile properties of Ethylene Vinyl Acetate (EVA)/Natural Rubber (NR)/MLF composites. Treated MLF were mixed with the EVA/NR blend in Haake internal mixer at 120 °C and rotor speed of 50 rpm for 10 minutes. Fibre morphology and the fibre/matrix interface ware further characterized by scanning electron microscopy (SEM). The tensile strength was increased by about 8% as compared to the composites with untreated fibers. The increased adhesion between fiber and matrix was also observed by SEM. Thus, EVA/NR/MLF composites reinforced with the treated fibres exhibited better tensile properties than untreated EVA/NR/MLF composites.

Twin-screw extruded lipid implants containing TRP2 peptide for tumour therapy.

PubMed

Even, Marie-Paule; Bobbala, Sharan; Gibson, Blake; Hook, Sarah; Winter, Gerhard; Engert, Julia

2017-05-01

Much effort has been put in the development of specific anti-tumour immunotherapies over the last few years, and several studies report on the use of liposomal carriers for tumour-associated antigens. In this work, the use of lipid implants, prepared using two different extruders, was investigated for sustained delivery in tumour therapy. The implants consisted of cholesterol, soybean lecithin, Dynasan 114, trehalose, ovalbumin (OVA) or a TRP2 peptide, and Quil-A. Implants were first produced on a Haake Minilab extruder, and then a scale-down to minimal quantities of material on a small scale ZE mini extruder was performed. All formulations were characterised in terms of extrudability, implant properties and in vitro release behaviour of the model antigen ovalbumin. The type of extruder used to produce the implants had a major influence on implant properties and the release behaviour, demonstrating that extrusion parameters and lipid formulations have to be individually adapted to each extrusion device. Subsequently, lipid implants containing TRP-2 peptide were extruded on the ZE mini extruder and investigated in vitro and in vivo. The in vivo study showed that mice having received TRP2 loaded implants had delayed tumour growth for 3days compared to groups having received no TRP2. Copyright © 2017 Elsevier B.V. All rights reserved.

The Structure and Molecular Parameters of Camphene Determined by Fourier Transform Microwave Spectroscopy and Quantum Chemical Calculations

NASA Astrophysics Data System (ADS)

Neeman, Elias M.; Dréan, Pascal; Huet, T. R.

2016-06-01

The emission of volatile organic compounds, from plants has strong revelance for plant physiology, plant ecology and atmospheric chemistry. Camphene (C10H16) is a bicyclic monoterpene which is emitted in the atmosphere by biogenic sources. The structure of the unique stable conformer was optimized using density functional theory and ab initio calculations. The rotational spectrum of camphene was recorded in a supersonic jet expansion with a Fourier transform microwave spectrometer over the range 2-20 GHz. Signals from the parent species and from the ten 13C isotopomers were observed in natural abundance. The rotational and centrifugal distortion parameters were fitted to a Watson's Hamiltonian in the A-reduction. A magnetic hyperfine structure associated with the pairs of hydrogen nuclei in the methylene groups was observed and modeled.The rotational constants coupled to the equilibrium structure calculations were used to determine the r_0 and the r_m(1) gas-phase geometries of the carbon skeleton. The present work provides the first spectroscopic characterization of camphene in the gas phase and these results are also relevant for ozonolysis kinetics study through Criegee intermediates. R. Baraldi, F. Rapparini, O. Facini, D. Spano and P. Duce, Journal of Mediterranean Ecology, Vol.6, No.1, (2005). A. Bracho-Nunez, N. M. Knothe, S. Welter, M. Staudt, W. R. Costa, M. A. R. Liberato, M. T. F. Piedade, and J. Kesselmeier Biogeosciences, 10, 5855-5873, (2013). Minna Kivimäenpää, Narantsetseg Magsarjav, Rajendra Ghimire, Juha-Matti Markkanen, Juha Heijari, Martti Vuorinen and Jarmo K. Holopainen, Atmospheric Environment, 60, 477-485, (2012). R.C. de M. Oliveira and G. F. Bauerfeldt, J. Phys. Chem. A, 119 2802-2812 (2015)

Magnetic and microwave absorbing properties of magnetite-thermoplastic natural rubber nanocomposites

NASA Astrophysics Data System (ADS)

Kong, Ing; Hj Ahmad, Sahrim; Hj Abdullah, Mustaffa; Hui, David; Nazlim Yusoff, Ahmad; Puryanti, Dwi

2010-11-01

Magnetic and microwave absorbing properties of thermoplastic natural rubber (TPNR) filled magnetite (Fe 3O 4) nanocomposites were investigated. The TPNR matrix was prepared from polypropylene (PP), natural rubber (NR) and liquid natural rubber (LNR) in the ratio of 70:20:10 with the LNR as the compatibilizer. TPNR-Fe 3O 4 nanocomposites with 4-12 wt% Fe 3O 4 as filler were prepared via a Thermo Haake internal mixer using a melt-blending method. XRD reveals the presence of cubic spinel structure of Fe 3O 4 with the lattice parameter of a=8.395 Å. TEM micrograph shows that the Fe 3O 4 nanoparticles are almost spherical with the size ranging 20-50 nm. The values of saturation magnetization ( MS), remanence ( MR), initial magnetic susceptibility ( χi) and initial permeability ( μi) increase, while the coercivity ( HC) decreases with increasing filler content for all compositions. For nanocomposites, the values of the real ( ɛr') and imaginary permittivity ( ɛr'') and imaginary permeability ( μr'') increase, while the value of real permeability ( μr') decreases as the filler content increases. The absorption or minimum reflection loss ( RL) continuously increases and the dip shifts to a lower frequency region with the increasing of both filler content in nanocomposites and the sample thickness. The RL is -25.51 dB at 12.65 GHz and the absorbing bandwidth in which the RL is less than -10 dB is 2.7 GHz when the filler content is 12 wt% at 9 mm sample thickness.

The influence of propolis on rheological properties of lipstick.

PubMed

Goik, U; Ptaszek, A; Goik, T

2015-08-01

The aim of this work was to study the effect of propolis on the rheological and textural properties of lipsticks. The studied lipsticks were based on raw materials and contained no synthetic compounds, preservatives, fragrances or dyes. The rheological and textural properties of the prepared lipsticks, both with and without propolis, were studied as a function of temperature and storage period. Measurements were taken using an RS6000 rheometer (Haake, Germany) with a cone-plate sensor. The cone parameters were as follows: diameter 35 mm and angle 2°. Textural tests were performed using the same cone-plate geometry. The research results of rheological and textural properties of lipsticks, with and without the addition of propolis, indicate the possibility of application of propolis as a beneficial additive to such type of cosmetics. The presence of propolis does not significantly alter the viscoelastic properties of the lipsticks. The courses of flow curves indicate shear thinning, which is very advantageous from an application point of view. From the rheological point of view, the properties of lipsticks tested in low deformation conditions show some structural changes, most likely due to consolidation of the structure. The analysis of textural properties indicates that lipsticks with added propolis are more brittle and prone to crushing. However, the temperature increase (30°C) does not cause significant changes to the textural characteristics of these lipsticks. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Effect of liquid epoxidized natural rubber (LENR) on mechanical properties and morphology of natural rubber/high density polyethylene/mengkuang fiber (NR/HDPE/MK) bio-composite

NASA Astrophysics Data System (ADS)

Piah, Mohd Razi Mat; Baharum, Azizah

2016-11-01

The use of mengkuang fiber (MK) fibers in NR/HDPE (40/60) blend was studied via surface modification of fiber. The MK fiber was pre-washed with 5%wt/v sodium hydroxide solution prior to treatment with liquid epoxidized natural rubber (LENR). The concentration of LENR were varied from 5%-20%wt in toluene. The effects of LENR concentrations were studied in terms of mechanical properties and morphology formed. Melt-blending was performed using an internal mixer (Haake Rheomix 600). The processing parameters identified were 135°C temperature, 45 rpm rotor speed, 12 minutes processing time and at 20%wt MK fiber loading. The optimum LENR treatment concentration was obtained at 5%wt with tensile strength, tensile modulus, and impact strength of 10.3 MPa, 414.2 MPa and 14.4 kJ/m2 respectively. The tensile modulus of LENR-treated MK fiber filled NR/HDPE bio-composite has shown enhancement up to 16.7% higher than untreated MK fiber. The tensile and impact strength were decreased with increasing LENR concentration due to the broken of MK fibers to smaller particles and adhered to each other. FESEM micrographs confirmed the formation of fiber-fiber agglomeration in NR/HDPE blends. The optical microscope analysis shows MK fibers is shorter than original fiber lengths after NaOH-LENR surface modification. The internal bonding forces of MK fiber seems to be weaker than external force exerted on it, therefore, the MK fiber has broken to smaller particles and reduced the mechanical properties of NR/HDPE/MK(20%) bio-composite.

Graphene oxide-silica nanohybrids as fillers for PA6 based nanocomposites

NASA Astrophysics Data System (ADS)

Maio, A.; Fucarino, R.; Khatibi, R.; Botta, L.; Rosselli, S.; Bruno, M.; Scaffaro, R.

2014-05-01

Graphene oxide (GO) was prepared by oxidation of graphite flakes by a mixture of H2SO4/H3PO4 and KMnO4 based on Marcano's method. Two different masterbatches containing GO (33.3%) and polyamide-6 (PA6) (66.7%) were prepared both via solvent casting in formic acid and by melt mixing in a mini-extruder (Haake). The two masterbatches were then used to prepare PA6-based nanocomposites with a content of 2% in GO. For comparison, a nanocomposite by direct mixing of PA6 and GO (2%) and PA6/graphite nanocomposites were prepared, too. The oxidation of graphite into GO was assessed by X-ray diffraction (XRD), Micro-Raman spectroscopy, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) analyses. All these techniques demonstrated the effectiveness of the graphite modification, since the results put into evidence that, after the acid treatment, interlayer distance, oxygen content and defects increased. SEM micrographs carried out on the nanocomposites, showed GO layers totally surrounded by polyamide-6, this feature is likely due to the strong interaction between the hydrophilic moieties located both on GO and on PA6. On the contrary, no interactions were observed when graphite was used as filler. Mechanical characterization, carried out by tensile and dynamic-mechanical tests, marked an improvement of the mechanical properties observed. Photoluminescence and EPR measurements were carried out onto nanoparticles and nanocomposites to study the nature of the interactions and to assess the possibility to use this class of materials as semiconductors or optical sensors.

Racial and ethnic minority college students' stigma associated with seeking psychological help: Examining psychocultural correlates.

PubMed

Cheng, Hsiu-Lan; Kwan, Kwong-Liem Karl; Sevig, Todd

2013-01-01

Many college students underuse professional psychological help for mental health difficulties. The stigma associated with seeking such help appears to be one of the reasons for this underuse. Levels of psychological distress and past use of counseling/psychotherapy have been found to be important correlates of stigma associated with seeking psychological help (Obasi & Leong, 2009; Vogel, Wade, & Haake, 2006). For racial and ethnic minorities, the hindering effects of self-stigma and perceived stigmatization by others on treatment seeking may further be compounded by their relationships with their own ethnic groups, with other ethnic groups, and with the dominant society. This study used structural equation modeling (SEM) to test a model that explored the effects of psychological distress and psychocultural variables (i.e., ethnic identity, other-group orientation, perceived discrimination) on perceived stigmatization by others and self-stigma for seeking psychological help, controlling for past use of counseling/psychotherapy. The sample consisted of 260 African American, 166 Asian American, and 183 Latino American students. SEM multigroup analyses indicated measurement invariance, but partial structural invariance, across racial/ethnic groups. Across all 3 groups, higher levels of psychological distress and perceived racial/ethnic discrimination, respectively, predicted higher levels of perceived stigmatization by others for seeking psychological help, which, in turn, predicted greater self-stigma for seeking psychological help. Higher levels of other-group orientation predicted lower levels of self-stigma of seeking psychological help across groups. Higher levels of ethnic identity predicted lower levels of self-stigma of seeking psychological help only for African Americans. Implications for research and practice are discussed. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Graphene oxide-silica nanohybrids as fillers for PA6 based nanocomposites

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maio, A.; Fucarino, R.; Khatibi, R.

Graphene oxide (GO) was prepared by oxidation of graphite flakes by a mixture of H{sub 2}SO{sub 4}/H{sub 3}PO{sub 4} and KMnO{sub 4} based on Marcano's method. Two different masterbatches containing GO (33.3%) and polyamide-6 (PA6) (66.7%) were prepared both via solvent casting in formic acid and by melt mixing in a mini-extruder (Haake). The two masterbatches were then used to prepare PA6-based nanocomposites with a content of 2% in GO. For comparison, a nanocomposite by direct mixing of PA6 and GO (2%) and PA6/graphite nanocomposites were prepared, too. The oxidation of graphite into GO was assessed by X-ray diffraction (XRD),more » Micro-Raman spectroscopy, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) analyses. All these techniques demonstrated the effectiveness of the graphite modification, since the results put into evidence that, after the acid treatment, interlayer distance, oxygen content and defects increased. SEM micrographs carried out on the nanocomposites, showed GO layers totally surrounded by polyamide-6, this feature is likely due to the strong interaction between the hydrophilic moieties located both on GO and on PA6. On the contrary, no interactions were observed when graphite was used as filler. Mechanical characterization, carried out by tensile and dynamic-mechanical tests, marked an improvement of the mechanical properties observed. Photoluminescence and EPR measurements were carried out onto nanoparticles and nanocomposites to study the nature of the interactions and to assess the possibility to use this class of materials as semiconductors or optical sensors.« less

Preparation and Properties of Ethylene Vinyl Acetate Copolymer/Silica Nanocomposites in Presence of EVA-g-Acrylic Acid.

PubMed

Tham, Do Quang; Tuan, Vu Manh; Thanh, Dinh Thi Mai; Chinh, Nguyen Thuy; Giang, Nguyen Vu; Trang, Nguyen Thi Thu; Hang, To Thi Xuan; Huong, Ho Thu; Dung, Nguyen Thi Kim; Hoang, Thai

2015-04-01

Here we report a facile approach to enhance the dispersibility of ethylene vinyl acetate copolymer (EVA)/silica nanocomposites (for the EVA/silica nanocomposites and interaction between silica nanoparticles (nanosilica) and EVA by adding EVA-g-acrylic acid (EVAgAA) as a compatibilizer, which was formed by grafting acrylic acid onto EVA chains with the aid of dicumyl peroxide). The above nanocomposites with and without EVAgAA were prepared by melt mixing in a Haake intermixer with different contents of silica and EVAgAA. Their structure and morphology were characterized by Fourier transform infra-red (FT-IR) spectroscopy, field emission scanning electron microscopy (FE-SEM), and the mechanical, rheological, dielectrical, and flammability properties of the nanocomposites were also investigated. The FT-IR spectra of the nanocomposites confirmed the formation of hydrogen bonds between the surface silanol groups of nanosilica and C=O groups of EVA and/or EVAgAA. The presence of EVAgAA remarkably increased the intensity of hydrogen bonding between nanosilica and EVA which not only enhanced the dispersion of nanosilica in EVA matrix but also increased the mechanical, viscosity and storage modulus of EVA/silica nanocomposites. In addition, the flammability of EVA/silica nanocomposites is also significantly reduced after the functionalization with EVAgAA. However, the mechanical properties of EVA/silica nanocomposites tended to level off when its content was above 1.5 wt.%. It has also been found that the dielectric constant value of the EVA/EVAgAA/silica nanocomposites is much lower than that of the EVA/silica nanocomposites, which is another evidence of the hydrogen bonding formation between EVAgAA and nanosilica.

Innovations in Rheometer Controlled-Rate Control Loop Design: Ultra Low Angular Speed Control and New Applications

NASA Astrophysics Data System (ADS)

Schulz, Ulrich; Sierro, Philippe; Nijman, Jint

2008-07-01

The design and implementation of an angular speed control loop for a universal rheometer is not a trivial task. The combination of a highly dynamic, very low inertia (drag cup) motor (motor inertia is 10-5 kg m2) with samples which can range in viscosity from 10-3 Pas to 108 Pas, which can be between purely viscous and higly viscoelastic, which can exhibit yield-stresses, etc. asks for a highly adaptive digital control loop. For the HAAKE MARS rotational rheometer a new adaptive control loop was developed which allows the control of angular speeds as low 5×10-9 rad/s and response times a short as 10 ms. The adaptation of the control loop to "difficult" samples is performed by analysing the response of the complete system to a short pre-test. In this paper we will show that the (very) short response times at (very) low angular speeds are not only achieved with ideal samples, but due to the adaptable control loop, also with "difficult" samples. We will show measurement results on "difficult" samples like cosmetic creams and emulsions, a laponite gel, etc. to proof that angular speeds down to 10-4 rad/s are reached within 10 ms to 20 ms and angular speeds down to 10-7 rad/s within 1 s to 2 s. The response times for reaching ultra low angular speeds down to 5×10-9 rad/s are in the order of 10 s to 30 s. With this new control loop it is, for the first time, possible to measure yield stresses by applying a very low constant shear-rate to the sample and measuring the torque response as a function of time.

Correlation of shear and dielectric ion viscosity of dental resins - Influence of composition, temperature and filler content.

PubMed

Steinhaus, Johannes; Hausnerova, Berenika; Haenel, Thomas; Selig, Daniela; Duvenbeck, Fabian; Moeginger, Bernhard

2016-07-01

Shear viscosity and ion viscosity of uncured visible light-curing (VLC) resins and resin based composites (RBC) are correlated with respect to the resin composition, temperature and filler content to check where Dielectric Analysis (DEA) investigations of VLC RBC generate similar results as viscosity measurements. Mixtures of bisphenol A glycidyl methacrylate (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) as well as the pure resins were investigated and compared with two commercial VLC dental resins and RBCs (VOCO, Arabesk Top and Grandio). Shear viscosity data was obtained using a Haake Mars III, Thermo Scientific. Ion viscosity measurements performed by a dielectric cure analyzer (DEA 231/1 Epsilon with Mini IDEX-Sensor, Netzsch-Gerätebau). Shear viscosity depends reciprocally on the mobility of molecules, whereas the ion viscosity also depends on the ion concentration as it is affected by both ion concentration and mixture viscosity. Except of pure TEGDMA, shear and ion viscosities depend on the resin composition qualitatively in a similar manner. Furthermore, shear and ion viscosities of the commercial VLC dental resins and composites exhibited the same temperature dependency regardless of filler content. Application of typical rheological models (Kitano and Quemada) revealed that ion viscosity measurements can be described with respect to filler contents of up to 30vol.%. Rheological behavior of a VLC RBC can be characterized by DEA under the condition that the ion concentration is kept constant. Both methods address the same physical phenomenon - motion of molecules. The proposed relations allows for calculating the viscosity of any Bis-GMA-TEGDMA mixture on the base of the viscosities of the pure components. This study demonstrated the applicability of DEA investigations of VLC RBCs with respect to quality assurance purposes. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Rapid-Adiabatic Control of Ro-Vibrational Populations in Polyatomic Molecules

NASA Astrophysics Data System (ADS)

Zak, Emil J.; Yachmenev, Andrey

2017-06-01

We present a simple method for control of ro-vibrational populations in polyatomic molecules in the presence of inhomogeneous electric fields [1]. Cooling and trapping of heavy polar polyatomic molecules has become one of the frontier goals in high-resolution molecular spectroscopy, especially in the context of parity violation measurement in chiral compounds [2]. A key step toward reaching this goal would be development of a robust and efficient protocol for control of populations of ro-vibrational states in polyatomic, often floppy molecules. Here we demonstrate a modification of the stark-chirped rapid-adiabatic-passage technique (SCRAP) [3], designed for achieving high levels of control of ro-vibrational populations over a selected region in space. The new method employs inhomogeneous electric fields to generate space- and time- controlled Stark-shifts of energy levels in molecules. Adiabatic passage between ro-vibrational states is enabled by the pump pulse, which raises the value of the Rabi frequency. This Stark-chirped population transfer can be used in manipulation of population differences between high-field-seeking and low-field-seeking states of molecules in the Stark decelerator [4]. Appropriate timing of voltages on electric rods located along the decelerator combined with a single pump laser renders our method as potentially more efficient than traditional Stark decelerator techniques. Simulations for NH_3 show significant improvement in effectiveness of cooling, with respect to the standard 'moving-potential' method [5]. At the same time a high phase-space acceptance of the molecular packet is maintained. E. J. Zak, A. Yachmenev (submitted). C. Medcraft, R. Wolf, M. Schnell, Angew. Chem. Int. Ed., 53, 43, 11656-11659 (2014) M. Oberst, H. Munch, T. Halfman, PRL 99, 173001 (2007). K. Wohlfart, F. Grätz, F. Filsinger, H. Haak, G. Meijer, J. Küpper, Phys. Rev. A 77, 031404(R) (2008). H. L. Bethlem, F. M. H. Crompvoets, R. T. Jongma, S. Y. T. van de

Grafting of a reactive siloxane onto an alpha-olefin in the melt phase

NASA Astrophysics Data System (ADS)

Bekele, Solomon

1999-11-01

This dissertation presents the outcomes of a study undertaken to graft a reactive siloxane onto an alpha-olefin in the melt phase with the objective of conducting grafting and sequentially making a film of low coefficient of friction in a twin screw extruder. The areas of focus of the research were (1) design of experiments, (2) batch kinetic study, (3) twin screw extruder grafting and film making and (4) film property analysis. The primary materials of the study were a film grade homopolymer polyethylene, Equistar NA345-013, a vinylmethylsiloxane-dimethylsiloxane copolymer, Gelest VDT-731, and an ethyl 3,3-di-(t-amylperoxy)-butyrate, Elf Atochem Lupersol 533-M75. The batch mixer was a Haake rheomixRTM 400 modified to conduct reaction under a N2 blanket. Continuous reactive extrusion and sequential film making was done in a Leistritz 18mm x 40/1 L/D corotating and intermeshing twin screw extruder coupled with a flex lip die. Reaction samples were analyzed using FT-IR for degree of grafting and GPC to determine changes in molecular weight distribution as measures of degree of side reactions. The factors with main effects on degree of grafting were found to be mole percent vinyl functionality available for reaction, amount of initiator and mixing temperature. Among side reactions chain scission was found to be absent. The degree of cross-linking was mainly dependent on mole percent of free radical initiator and mixing temperature. Grafting was found to be a third order reaction with respect to vinylsiloxane concentration. Batch kinetic data were scaled up to continuous reactive extrusion in the twin screw extruder. Tracer experiments with TiO2 were used to estimate the average residence time and the extent of axial dispersion. An axial plug flow dispersion model was assumed to represent the nonideal flow of the grafting reaction in the twin screw extruder. The model was found to under predict the degree of grafting from 9% up to 25%. The coefficient of friction of

North Atlantic early 20th century warming and impact on European summer: Mechanisms and Predictability

NASA Astrophysics Data System (ADS)

Müller, Wolfgang

2017-04-01

During the last century, substantial climate variations in the North Atlantic have occurred, such as the warmings in the 1920s and 1990s. Such variations are considered to be part of the variability known as the Atlantic Multidecadal Variations (AMV) and have a strong impact on local climates such as European summers. Here a synthesis of previous works is presented which describe the occurrence of the warming in the 1920s in the North Atlantic and its impact on the European summer climate (Müller et al. 2014, 2015). For this the 20th century reanalysis (20CR) and 20CR forced ocean experiments are evaluated. It can be shown that the North Atlantic Current and Sub-Polar Gyre are strengthened as a result of an increased pressure gradient over the North Atlantic. Concurrently, Labrador Sea convection and Atlantic meridional overturning circulation (AMOC) increase. The intensified NAC, SPG, and AMOC redistribute sub-tropical water into the North Atlantic and Nordic Seas, thereby increasing observed and modelled temperature and salinity during the 1920s. Further a mechanism is proposed by which North Atlantic heat fluxes associated with the AMV modulate European decadal summer climate (Ghosh et al. 2016). By using 20CR, it can be shown that multi-decadal variations in the European summer temperature are associated to a linear baroclinic atmospheric response to the AMV-related surface heat flux. This response induce a sea level pressure structure modulating meridional temperature advection over north-western Europe and Blocking statistics over central Europe. This structure is shown to be the leading mode of variability and is independent of the summer North Atlantic Oscillation. Ghosh, R., W.A. Müller, J. Bader, and J. Baehr, 2016: Impact of observed North Atlantic multidecadal variations to European summer climate: A linear baroclinic response to surface heating. Clim. Dyn. doi:10.10007/s00382-016-3283-4 Müller W. A., D. Matei, M. Bersch, J. H. Jungclaus, H. Haak, K

A new method for the continuous production of single dosed controlled release matrix systems based on hot-melt extruded starch: analysis of relevant process parameters and implementation of an in-process control.

PubMed

Kipping, Thomas; Rein, Hubert

2013-05-01

In the present study, we evaluated a novel processing technique for the continuous production of hot-melt extruded controlled release matrix systems. A cutting technique derived from plastics industry, where it is widely used for cutting of cables and wires was adapted into the production line. Extruded strands were shaped by a rotary fly cutter. Special focus is laid on the development of a process analytical technology by evaluating signals obtained from the servo control of the rotary fly cutter. The intention is to provide a better insight into the production process and to offer the ability to detect small variations in process-variables. A co-rotating twin-screw extruder ZSE 27 HP-PH from Leistritz (Nürnberg, Germany) was used to plasticize the starch; critical extrusion parameters were recorded. Still elastic strands were shaped by a rotary fly-cutter type Dynamat 20 from Metzner (Neu-Ulm, Germany). Properties of the final products were analyzed via digital image analysis to point out critical parameters influencing the quality. Important aspects were uniformity of diameter, height, roundness, weight, and variations in the cutting angle. Stability of the products was measured by friability tests and by determining the crushing strength of the final products. Drug loading studies up to 70% were performed to evaluate the capacity of the matrix and to prove the technological feasibility. Changes in viscosities during API addition were analyzed by a Haake Minilab capillary rheometer. X-ray studies were performed to investigate molecular structures of the matrices. External shapes of the products were highly affected by die-swelling of the melt. Reliable reproducibility concerning uniformity of mass could be achieved even for high production rates (>2500cuts/min). Both mechanical strength and die-swelling of the products could be linked to the ratio of amylose to amylopectin. Formulations containing up to 70% of API could still be processed. Viscosity

Use of surfactants as plasticizers in preparing solid dispersions of poorly soluble API: stability testing of selected solid dispersions.

PubMed

Ghebremeskel, Alazar N; Vemavarapu, Chandra; Lodaya, Mayur

2006-08-01

The purpose of the study is to evaluate the effect of surfactant-plasticizers on the physical stability of amorphous drug in polymer matrices formed by hot melt extrusion. Solid dispersions of a poorly soluble drug were prepared using PVP-K30, Plasdone-S630, and HPMC-E5 as the polymeric carriers and surfactants as plasticizers. The solid dispersions were produced by hot melt extrusion at temperatures 10 degrees C above and below the glass transition temperature (Tg) of the carrier polymers using a 16 mm-Haake Extruder. The surfactants tested in this study included Tween-80 and Docusate Sodium. The particle size of the extrudate was reduced to have mean of 100-200 micron. The physical stability of the solid dispersions produced was monitored at 30 degrees C/60% for six-months and at 60 degrees C/85% for two-months in open HDPE bottles. Modulated differential scanning calorimetry, polarized light microscopy, powder X-ray diffraction and dissolution testing was performed to assess the physical stability of solid dispersions upon stress testing. The dispersions containing HPMC-E5 were observed especially to be susceptible to physical instability under an accelerated stress conditions (60 degrees C/85%RH) of the solid dispersion. About 6% conversion of amorphous drug to crystalline form was observed. Consequently, the system exhibits similar degree of re-crystallization upon addition of the surfactant. However, under 30 degrees C/60%RH condition, the otherwise amorphous Drug-HPMC-E5 system has been destabilized by the addition of the surfactant. This effect is much more reduced in the extruded solid dispersions where polymeric carriers such as Plasdone S-603 and PVP-K30 (in addition to surfactants) are present. Furthermore, the drug release from the solid dispersions was unaffected at the stress conditions reported above. Possible reasons for the enhanced stability of the dispersions are due to the surfactants ability to lower the viscosity of the melt, increase the API

Reconstructing Links between AMOC and Surface Temperature Variability in the North Atlantic

NASA Astrophysics Data System (ADS)

Borchert, Leonard; Fischer, Matthias; Müller, Wolfgang; Baehr, Johanna

2016-04-01

Kruger, GJ Marshall, M Mauger, HY Mok, Ø Nordli, TF Ross, RM Trigo, XL Wang, SD Woodruff, SJ Worley (2011): The Twentieth Century Reanalysis Project. Q J R Meteorol Soc, 137: 1-28 Müller, W, D Matei, M Bersch, JH Jungclaus, H Haak, K Lohmann, GP Compo, PD Sardeshmukh, J Marotzke (2014): A twentieth-century reanalysis forced ocean model to reconstruct the North Atlantic climate variation during the 1920s. Clim Dyn, 44: 1935-1955

Progress in Global Multicompartmental Modelling of DDT

NASA Astrophysics Data System (ADS)

Stemmler, I.; Lammel, G.

2009-04-01

input parameters. Furthermore, better resolution of some processes could improve model performance. References: Marsland S.J., Haak H., Jungclaus J.H., Latif M., Röske F. (2003): The Max-Planck-Institute global ocean/sea ice model with orthogonal curvilinear coordinates. Ocean Modelling 5, 91-127 Maier-Reimer E. , Kriest I., Segschneider J., Wetzel P. : The HAMburg Ocean Carbon Cycle Model HAMOCC 5.1 - Technical Description Release 1.1 (2005),Reports on Earth System Science 14 Stier P. , Feichter J. (2005), Kinne S., Kloster S., Vignati E., Wilson J.Ganzeveld L., Tegen I., Werner M., Blakanski Y., Schulz M., Boucher O., Minikin A., Petzold A.: The aerosol-climate model ECHAM5-HAM. Atmos. Chem. Phys 5, 1125-1156 Semeena V.S., Feichter J., Lammel G. (2006): Impact of the regional climate and substance properties on the fate and atmospheric long-range transport of persistent organic pollutants - examples of DDT and γ-HCH. Atmos. Chem. Phys. 6, 1231-1248

OH Fluorescence and Prompt Emission in comet 103P/Hartley 2 observed by EPOXI mission and expected results for comet 67P/Churyumov-Gerasimenko observed by Rosetta/OSIRIS WAC camera

NASA Astrophysics Data System (ADS)

La Forgia, F.; A'Hearn, M. F.; Lazzarin, M.; Magrin, S.; Bodewits, D.; Bertini, I.; Pajola, M.; Barbier, C.; Sierks, H.

2014-04-01

The OH radical, observed in cometary comae, is the direct dissociation product of water. Given the strong A2∑ - X2II (0, 0) emission band in the near-UV at 308.5 nm due to resonance fluorescence, the OH radical has been used, for years, as a tracer of the water parent molecule. Specifically, the OH fluorescence band provides an immediate tool to monitor the water production rate and its variations with the comet's heliocentric distance, rotational period and possible activity changes. Photolysis of water in cometary comae gives rise, with a non negligible branching ratio, to OH fragments in the first electronically excited state (OH*). This state is very unstable, with a lifetime of about 10-6s (Becker and Haaks, 1973), therefore OH* molecules promptly decay to the ground state. This process, generally referred to as prompt emission (PE), is responsible for an emission band in the near-UV ranging approximatelly from 306 to 325 nm. Original studies and tentative detections of OH PE have been put forth by Bertaux (1986), Budzien and Feldman (1991), Bonev et al. (2004), A'Hearn et al. (2007) using ground and space observations. Both from the above mentioned works together with our analysis, this process is expected to be prominent at short distances from the nucleus, where there is high density of water molecules, requiring the need of spacecraft observations to reach the necessary resolution. The hyperactive Jupiter family comet 103P/Hartley 2 has been visited by EPOXI spacecraft on 4 November 2010 at a minimum distance of 694 km, when it was at 1.064 AU from the Sun (A'Hearn et al. 2011). We present the analysis of photometric observations in OH filter acquired by MRI camera onboard EPOXI used to investigate the spatial distribution of OH in the coma of Hartley 2. The data revealed a radial OH structure within 35 km from the nucleus, appearing to be coming directly from the nucleus, in the region of the central waist. A theoretical computation evidencing a strong

The InterFrost benchmark of Thermo-Hydraulic codes for cold regions hydrology - first inter-comparison phase results

NASA Astrophysics Data System (ADS)

Grenier, Christophe; Rühaak, Wolfram

2016-04-01

Climate change impacts in permafrost regions have received considerable attention recently due to the pronounced warming trends experienced in recent decades and which have been projected into the future. Large portions of these permafrost regions are characterized by surface water bodies (lakes, rivers) that interact with the surrounding permafrost often generating taliks (unfrozen zones) within the permafrost that allow for hydrologic interactions between the surface water bodies and underlying aquifers and thus influence the hydrologic response of a landscape to climate change. Recent field studies and modeling exercises indicate that a fully coupled 2D or 3D Thermo-Hydraulic (TH) approach is required to understand and model past and future evolution such units (Kurylyk et al. 2014). However, there is presently a paucity of 3D numerical studies of permafrost thaw and associated hydrological changes, which can be partly attributed to the difficulty in verifying multi-dimensional results produced by numerical models. A benchmark exercise was initialized at the end of 2014. Participants convened from USA, Canada, Europe, representing 13 simulation codes. The benchmark exercises consist of several test cases inspired by existing literature (e.g. McKenzie et al., 2007) as well as new ones (Kurylyk et al. 2014; Grenier et al. in prep.; Rühaak et al. 2015). They range from simpler, purely thermal 1D cases to more complex, coupled 2D TH cases (benchmarks TH1, TH2, and TH3). Some experimental cases conducted in a cold room complement the validation approach. A web site hosted by LSCE (Laboratoire des Sciences du Climat et de l'Environnement) is an interaction platform for the participants and hosts the test case databases at the following address: https://wiki.lsce.ipsl.fr/interfrost. The results of the first stage of the benchmark exercise will be presented. We will mainly focus on the inter-comparison of participant results for the coupled cases TH2 & TH3. Both cases

The Rheology of a Three Component System: COAL/WATER/#4 Oil Emulsions.

NASA Astrophysics Data System (ADS)

Gilmartin, Barbara Jean

The purpose of this investigation was to study the rheology of a three component system, coal/water/#4 oil emulsions (COW), in which the third component, water, was present in a significant concentration, and to determine the applicability of existing theories from suspension rheology to the three component system studied. In a coal/water/oil emulsion, free coal particles adhere to the surface of the water droplets, preventing their coagulation, while the larger coal particles reside in the matrix of stabilized water droplets. The use of liquid fuels containing coal is a means of utilizing our nation's coal reserves while conserving oil. These fuels can be burned in conventional oil-fired furnaces. In this investigation, a high sulfur, high ash, bituminous coal was used, along with a heavy #4 oil to prepare the emulsions. The coal was ground to a log-normal distribution with an average particle size of 62 microns. A Haake RV3 concentric cylinder viscometer, with a ribbed measuring system, was used to determine the viscosity of the emulsions. A physical pendulum settling device measured the shift in center of mass of the COW as a function of time. The flow behavior of the fuel in pipes was also tested. In interpreting the data from the viscometer and the pipe flow experiments, a power law analysis was used in the region from 30 s('-1) to 200 s('-1). Extrapolation methods were used to obtain the low and high shear behavior of the emulsions. In the shear rate region found in boiler feed systems, COW are shear thinning with a flow behavior index of 0.7. The temperature dependent characteristic of the emulsions studied were similar and followed an Arrhenius type relationship. The viscosity of the COW decreases with increasing coal average particle size and is also a function of the width of the size distribution used. The type of coal used strongly influences the rheology of the fuel. The volatile content and the atomic oxygen to nitrogen ratio of the coal are the most

Quantum Chaos

NASA Astrophysics Data System (ADS)

Casati, Giulio; Chirikov, Boris

2006-11-01

Preface; Acknowledgments; Introduction: 1. The legacy of chaos in quantum mechanics G. Casati and B. V. Chirikov; Part I. Classical Chaos and Quantum Localization: 2. Stochastic behaviour of a quantum pendulum under a periodic perturbation G. Casati, B. V. Chirikov, F. M. Izrailev and J. Ford; 3. Quantum dynamics of a nonintegrable system D. R. Grempel, R. E. Prange and S. E. Fishman; 4. Excitation of molecular rotation by periodic microwave pulses. A testing ground for Anderson localization R. Blümel, S. Fishman and U. Smilansky; 5. Localization of diffusive excitation in multi-level systems D. K. Shepelyansky; 6. Classical and quantum chaos for a kicked top F. Haake, M. Kus and R. Scharf; 7. Self-similarity in quantum dynamics L. E. Reichl and L. Haoming; 8. Time irreversibility of classically chaotic quantum dynamics K. Ikeda; 9. Effect of noise on time-dependent quantum chaos E. Ott, T. M. Antonsen Jr and J. D. Hanson; 10. Dynamical localization, dissipation and noise R. F. Graham; 11. Maximum entropy models and quantum transmission in disordered systems J.-L. Pichard and M. Sanquer; 12. Solid state 'atoms' in intense oscillating fields M. S. Sherwin; Part II. Atoms in Strong Fields: 13. Localization of classically chaotic diffusion for hydrogen atoms in microwave fields J. E. Bayfield, G. Casati, I. Guarneri and D. W. Sokol; 14. Inhibition of quantum transport due to 'scars' of unstable periodic orbits R. V. Jensen, M. M. Sanders, M. Saraceno and B. Sundaram; 15. Rubidium Rydberg atoms in strong fields G. Benson, G. Raithel and H. Walther; 16. Diamagnetic Rydberg atom: confrontation of calculated and observed spectra C.-H. Iu, G. R. Welch, M. M. Kash, D. Kleppner, D. Delande and J. C. Gay; 17. Semiclassical approximation for the quantum states of a hydrogen atom in a magnetic field near the ionization limit M. Y. Kuchiev and O. P. Sushkov; 18. The semiclassical helium atom D. Wintgen, K. Richter and G. Tanner; 19. Stretched helium: a model for quantum chaos

Quantum Chaos

NASA Astrophysics Data System (ADS)

Casati, Giulio; Chirikov, Boris

1995-04-01

Preface; Acknowledgments; Introduction: 1. The legacy of chaos in quantum mechanics G. Casati and B. V. Chirikov; Part I. Classical Chaos and Quantum Localization: 2. Stochastic behaviour of a quantum pendulum under a periodic perturbation G. Casati, B. V. Chirikov, F. M. Izrailev and J. Ford; 3. Quantum dynamics of a nonintegrable system D. R. Grempel, R. E. Prange and S. E. Fishman; 4. Excitation of molecular rotation by periodic microwave pulses. A testing ground for Anderson localization R. Blümel, S. Fishman and U. Smilansky; 5. Localization of diffusive excitation in multi-level systems D. K. Shepelyansky; 6. Classical and quantum chaos for a kicked top F. Haake, M. Kus and R. Scharf; 7. Self-similarity in quantum dynamics L. E. Reichl and L. Haoming; 8. Time irreversibility of classically chaotic quantum dynamics K. Ikeda; 9. Effect of noise on time-dependent quantum chaos E. Ott, T. M. Antonsen Jr and J. D. Hanson; 10. Dynamical localization, dissipation and noise R. F. Graham; 11. Maximum entropy models and quantum transmission in disordered systems J.-L. Pichard and M. Sanquer; 12. Solid state 'atoms' in intense oscillating fields M. S. Sherwin; Part II. Atoms in Strong Fields: 13. Localization of classically chaotic diffusion for hydrogen atoms in microwave fields J. E. Bayfield, G. Casati, I. Guarneri and D. W. Sokol; 14. Inhibition of quantum transport due to 'scars' of unstable periodic orbits R. V. Jensen, M. M. Sanders, M. Saraceno and B. Sundaram; 15. Rubidium Rydberg atoms in strong fields G. Benson, G. Raithel and H. Walther; 16. Diamagnetic Rydberg atom: confrontation of calculated and observed spectra C.-H. Iu, G. R. Welch, M. M. Kash, D. Kleppner, D. Delande and J. C. Gay; 17. Semiclassical approximation for the quantum states of a hydrogen atom in a magnetic field near the ionization limit M. Y. Kuchiev and O. P. Sushkov; 18. The semiclassical helium atom D. Wintgen, K. Richter and G. Tanner; 19. Stretched helium: a model for quantum chaos

ADVANCED CUTTINGS TRANSPORT STUDY

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi

2004-01-31

Final design of the mast was completed (Task 5). The mast is consisting of two welded plate girders, set next to each other, and spaced 14-inches apart. Fabrication of the boom will be completed in two parts solely for ease of transportation. The end pivot connection will be made through a single 2-inch diameter x 4 feet-8 inch long 316 SS bar. During installation, hard piping make-ups using Chiksan joints will connect the annular section and 4-inch return line to allow full movement of the mast from horizontal to vertical. Additionally, flexible hoses and piping will be installed to isolatemore » both towers from piping loads and allow recycling operations respectively. Calibration of the prototype Foam Generator Cell has been completed and experiments are now being conducted. We were able to generate up to 95% quality foam. Work is currently underway to attach the Thermo-Haake RS300 viscometer and install a view port with a microscope to measure foam bubble size and bubble size distribution. Foam rheology tests (Task 13) were carried out to evaluate the rheological properties of the proposed foam formulation. After successful completion of the first foam test, two sets of rheological tests were conducted at different foam flow rates while keeping other parameters constant (100 psig, 70F, 80% quality). The results from these tests are generally in agreement with the previous foam tests done previously during Task 9. However, an unanticipated observation during these tests was that in both cases, the frictional pressure drop in 2 inch pipe was lower than that in the 3 inch and 4 inch pipes. We also conducted the first foam cuttings transport test during this quarter. Experiments on aerated fluids without cuttings have been completed in ACTF (Task 10). Gas and liquid were injected at different flow rates. Two different sets of experiments were carried out, where the only difference was the temperature. Another set of tests was performed, which covered a wide range

Nitrogen Isotopic Disequilibrium in the Cape York III A Iron

NASA Astrophysics Data System (ADS)

Zipfel, J.; Kim, Y.; Marti, K.

1995-09-01

disequilibrium as observed in Cape York include (a) survival of primary isotopic heterogeneities; (b) N loss during secondary processes, e.g., metamorphic heating and shock deformation: (a) Graphite grains within metal of the Acapulco meteorite were identified as carrier of isotopically distinct N and C components and were interpreted as surviving (possibly presolar) grains unaffected by the igneous alteration of the bulk meteorite (5). Obviously such grains exchanged N isotopically with metal and chromite, but not with sulfides and silicates, as these do not carry the light N of metal and chromite (6). The mechanism of this exchange is, however, unclear. No graphite has been observed so far in Cape York. Yet, isotopic heterogeneities in the precursor material of Cape York can not be excluded. During melting of the parent asteroid one would expect homogenization of the nitrogen isotopes. Since chromite and metal crystallize at high temperatures, a probable exchange of N between the S-rich melt and a distinct N reservoir at lower temperature might explain the disequilibrium. (b) Troilite nodules in Cape York indicate a small degree of shock deformation (2,3,5). One might argue that some N was lost and the residue fractionated during this event. However, 107Ag/109Ag ratios from metal and troilite correlate with Pd/Ag ratios, which is not the case in severely shocked magmatic irons (7). In addition, similar isotopic N fractionations are found in the "magmatic" Acapulco meteorite, which shows no indication of shock deformation. Therefore, secondary loss of N preferentially from troilite can be excluded. References: [1] Haak H. and Scott E. (1993) GCA, 57, 3457-3472. [2] Buchwald V. (1975) Handbook of Iron Meteorites, Vols. 1_3, Univ. of California and Arizona State Univ., Berkeley. [3] Kracher A et al. (1977) Geochem. J., 11, 207-217. [4] Murty S. and Marti K. (1994) GCA, 58, 1841-1848. [5] El Goresy A. et al. (1995) Nature, 373, 496-499. [6] Kim Y. et al. (1992) LPS XXIII, 691

EDITORIAL: Focus on Quantum Information and Many-Body Theory

NASA Astrophysics Data System (ADS)

Eisert, Jens; Plenio, Martin B.

2010-02-01

and F Verstraete SIMULATION AND DYNAMICS A quantum differentiation of k-SAT instances B Tamir and G Ortiz Classical Ising model test for quantum circuits Joseph Geraci and Daniel A Lidar Exact matrix product solutions in the Heisenberg picture of an open quantum spin chain S R Clark, J Prior, M J Hartmann, D Jaksch and M B Plenio Exact solution of Markovian master equations for quadratic Fermi systems: thermal baths, open XY spin chains and non-equilibrium phase transition Tomaž Prosen and Bojan Žunkovič Quantum kinetic Ising models R Augusiak, F M Cucchietti, F Haake and M Lewenstein ENTANGLEMENT AND SPECTRAL PROPERTIES Ground states of unfrustrated spin Hamiltonians satisfy an area law Niel de Beaudrap, Tobias J Osborne and Jens Eisert Correlation density matrices for one-dimensional quantum chains based on the density matrix renormalization group W Münder, A Weichselbaum, A Holzner, Jan von Delft and C L Henley The invariant-comb approach and its relation to the balancedness of multipartite entangled states Andreas Osterloh and Jens Siewert Entanglement scaling of fractional quantum Hall states through geometric deformations Andreas M Läuchli, Emil J Bergholtz and Masudul Haque Entanglement versus gap for one-dimensional spin systems Daniel Gottesman and M B Hastings Entanglement spectra of critical and near-critical systems in one dimension F Pollmann and J E Moore Macroscopic bound entanglement in thermal graph states D Cavalcanti, L Aolita, A Ferraro, A García-Saez and A Acín Entanglement at the quantum phase transition in a harmonic lattice Elisabeth Rieper, Janet Anders and Vlatko Vedral Multipartite entanglement and frustration P Facchi, G Florio, U Marzolino, G Parisi and S Pascazio Entropic uncertainty relations—a survey Stephanie Wehner and Andreas Winter Entanglement in a spin system with inverse square statistical interaction D Giuliano, A Sindona, G Falcone, F Plastina and L Amico APPLICATIONS Time-dependent currents of one-dimensional bosons

FOREWORD: The 70th birthday of Professor Stig Stenholm The 70th birthday of Professor Stig Stenholm

NASA Astrophysics Data System (ADS)

Suominen, Kalle-Antti

2010-09-01

information [7] and in Stockholm he had, again, very successful postdocs such as Ulf Leonhardt. Finally, in 2005, Stig Stenholm retired, although he is still active, writing papers, taking part in conferences and making research visits. We honoured his 70th birthday at the CEWQO2009 conference, and hope that the future provides us with further opportunities for such events. Looking at the obituary of Dirk ter Haar, I see that his style with students reminds me of Stig's approach. In my opinion, Stig expects independence and initiative from a student, giving perhaps a broad topic in which the student is expected to find his or her own way, whilst working perhaps with a postdoc. Juha Javanainen has talked about the 'sink or swim' style (not referring to Stig, though). There is a famous series of children's books about Moomin trolls by Tove Jansson (another Swedish-speaking Finn like Stig). In one of them, the Moomin find in early spring a small flower in a patch of land uncovered by snow, pushing its way up. One of them wants to cover it against frost during the night, but another says 'Don't, it'll fare better later if it has some difficulties at first'. At CEWQO2009 Stig gave the full list of his finished PhD students: Rainer Salomaa (1973), Temba Dlodlo (1980), Juha Javanainen (1980), Markus Lindberg (1985), Matti Kaivola (1985), Birger Ståhlberg (1985), Kalle-Antti Suominen (1992), Mackillo Kira (1995), Päivi Törmä (1996), Asta Paloviita (1997), Patrik Öhberg (1998), Martti Havukainen (1999), Erika Andersson (2000), Pawel Piwnicki (2001), Åsa Larson (2001), Markku Jääskeläinen (2003), and Jonas Larson (2005). One should also mention Erkki Kyrölä, who eventually graduated at Rochester and Olli Serimaa, who never graduated but published some important early-stage laser cooling work. As a final note I must mention a passion that Stig and I share, namely books. I have nearly 400 professional physics and mathematics books, but I am certain that the size of Stig