The Hot-Pressing of Hafnium Carbide (Melting Point, 7030 F)

NASA Technical Reports Server (NTRS)

Sanders, William A.; Grisaffe, Salvatore J.

1960-01-01

An investigation was undertaken to determine the effects of the hot-pressing variables (temperature, pressure, and time) on the density and grain size of hafnium carbide disks. The purpose was to provide information necessary for the production of high-density test shapes for the determination of physical and mechanical properties. Hot-pressing of -325 mesh hafnium carbide powder was accomplished with a hydraulic press and an inductively heated graphite die assembly. The ranges investigated for each variable were as follows: temperature, 3500 to 4870 F; pressure, 1000 to 6030 pounds per square inch; and time, 5 to 60 minutes. Hafnium carbide bodies of approximately 98 percent theoretical density can be produced under the following minimal conditions: 4230 F, 3500 pounds per square inch, and 15 minutes. Further increases in temperature and time resulted only in greater grain size.

Zirconium and hafnium in the southeastern Atlantic States

USGS Publications Warehouse

Mertie, J.B.

1958-01-01

The principal source of zirconium and hafnium is zircon, though a minor source is baddeleyite, mined only in Brazil. Zircon is an accessory mineral in igneous, metamorphic, and sedimentary rocks, but rarely occurs in hardrock in minable quantities. The principal sources of zircon are therefore alluvial deposits, which are mined in many countries of five continents. The principal commercial deposits in the United States are in Florida, though others exist elsewhere in the southeastern Coastal Plain. The evidence indicates that conditions for the accumulation of workable deposits of heavy minerals were more favorable during the interglacial stages of the Pleistocene epoch than during Recent time. Therefore detrital ores of large volume and high tenor are more likely to be found in the terrace deposits than along the present beaches. Other concentrations of heavy minerals, however, are possible at favored sites close to the Fall Line where the Tuscaloosa formation rests upon the crystalline rocks of the Piedmont province. A score of heavy and semiheavy minerals occur in the detrital deposits of Florida, but the principal salable minerals are ilmenite, leucoxene, rutile, and zircon, though monazite and staurolite are saved at some mining plants. Commercial deposits of heavy minerals are generally required to have a tenor of 4 percent, though ores with a lower tenor can be mined at a profit if the content of monazite is notably high. The percentages of zircon in the concentrates ranges from 10 to 16 percent, and in eastern Florida from 13 to 15 percent. Thus the tenor in zircon of the ore-bearing sands ranges from 0.4 to 0.6 percent. The content of hafnium in zircon is immaterial for many uses, but for some purposes very high or very low tenors in hafnium are required. Alluvial zircon cannot be separated into such varieties, which, if needed, must be obtained from sources in bedrock. It thus becomes necessary to determine the Hf : Zr ratios in zircon from many kinds of

Separation of Zirconium and Hafnium: A Review

NASA Astrophysics Data System (ADS)

Xu, L.; Xiao, Y.; van Sandwijk, A.; Xu, Q.; Yang, Y.

Zirconium is an ideal material for nuclear reactors due to its low absorption cross-section for thermal neutrons, whereas the typically contained hafnium with strong neutron-absorption is very harmful for zirconium. This paper provides an overview of the processes for separating hafnium from zirconium. The separation processes are roughly classified into hydro- and pyrometallurgical routes. The current dominant zirconium production route involves pyrometallurgical ore cracking, multi-step hydrometallurgical liquid-liquid extraction for hafnium removal and the reduction of zirconium tetrachloride to the pure metal by the Kroll process. The lengthy hydrometallurgical Zr-Hf separation operations leads to high production cost, intensive labour and heavy environmental burden. Using a compact pyrometallurgical separation method can simplify the whole production flowsheet with a higher process efficiency. The known separation methods are discussed based on the following reaction features: redox characteristics, volatility, electrochemical properties and molten salt extraction. The commercially operating extractive distillation process is a significant advance in Zr-Hf separation technology but it suffers from high process maintenance cost. The recently developed new process based on molten salt-metal equilibrium for Zr-Hf separation shows a great potential for industrial application, which is compact for nuclear grade zirconium production starting from crude ore. In the present paper, the available separation technologies are compared. The advantages and disadvantages as well as future directions of research and development for nuclear grade zirconium production are discussed.

High P-T phase transitions and P-V-T equation of state of hafnium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hrubiak, Rostislav; Drozd, Vadym; Karbasi, Ali

2016-07-29

We measured the volume of hafnium at several pressures up to 67 GPa and at temperatures between 300 to 780 K using a resistively heated diamond anvil cell with synchrotron x-ray diffraction at the Advanced Photon Source. The measured data allows us to determine the P-V-T equation of state of hafnium. The previously described [Xia et al., Phys. Rev. B 42, 6736-6738 (1990)] phase transition from hcp ({alpha}) to simple hexagonal ({omega}) phase at 38 GPa at room temperature was not observed even up to 51 GPa. The {omega} phase was only observed at elevated temperatures. Our measurements have alsomore » improved the experimental constraint on the high P-T phase boundary between the {omega} phase and high pressure bcc ({beta}) phase of hafnium. Isothermal room temperature bulk modulus and its pressure derivative for the {alpha}-phase of hafnium were measured to be B{sub 0} = 112.9{+-}0.5 GPa and B{sub 0}'=3.29{+-}0.05, respectively. P-V-T data for the {alpha}-phase of hafnium was used to obtain a fit to a thermodynamic P-V-T equation of state based on model by Brosh et al. [CALPHAD 31, 173-185 (2007)].« less

Hafnium transistor design for neural interfacing.

PubMed

Parent, David W; Basham, Eric J

2008-01-01

A design methodology is presented that uses the EKV model and the g(m)/I(D) biasing technique to design hafnium oxide field effect transistors that are suitable for neural recording circuitry. The DC gain of a common source amplifier is correlated to the structural properties of a Field Effect Transistor (FET) and a Metal Insulator Semiconductor (MIS) capacitor. This approach allows a transistor designer to use a design flow that starts with simple and intuitive 1-D equations for gain that can be verified in 1-D MIS capacitor TCAD simulations, before final TCAD process verification of transistor properties. The DC gain of a common source amplifier is optimized by using fast 1-D simulations and using slower, complex 2-D simulations only for verification. The 1-D equations are used to show that the increased dielectric constant of hafnium oxide allows a higher DC gain for a given oxide thickness. An additional benefit is that the MIS capacitor can be employed to test additional performance parameters important to an open gate transistor such as dielectric stability and ionic penetration.

Etude de la nitruration carbothermique du dioxyde de hafnium par diffraction X à haute température

NASA Astrophysics Data System (ADS)

Pialoux, A.

1993-03-01

The carbothermal reduction of hafnium dioxide under atmospheric level nitrogen pressure has been investigated using a graphite resistance high temperature X-ray diffractometer up to around 2300 K. A carbon transfer reaction through the gaseous phase (N 2, CO/CO 2) is shown to precede, then to compete the direct reduction of the hafnium oxide by the graphite in pure nitrogen. A complex mechanism has been found that accounts for the formation of hafnium dioxynitride and possibly of three other hafnium oxynitrides, then of hafnium mononitride and hafnium monocarbonitride, along two different steps between 1613 and 1923 K. An evaluation has been made concerning the composition of these γ 1- HfO 2-xN x/2□ x/2 (CaF 2-type structure), γ 2- Hf 7O 11N 2, γ 3- Hf 7O 8N 4 (rhombohedral), γ 4- Hf 2ON 2 (Mn 2O 3-type structure), HfN and HfN 1-zC z (NaCl-type structure) phases, considering the variations of their lattice parameters and the available data in the literature, especially on the isomorphous compounds of zirconium. It must be emphasized the new γ 1- HfO 2-xN x/2 phase, the dilatation of which is linear ( overlineα = 12×10 -6K -1), shows a constant composition from 2158 down to 1473 K (x ≈ 0,2). But under 1473 K, inevitably, the hafnium dioxynitride disappears, and poorly crystallized monoclinic αHfO 2 and rhombohedral γ 2- Hf 7O 11N 2 are formed.

RF sputtered silicon and hafnium nitrides as applied to 440C steel

NASA Technical Reports Server (NTRS)

Grill, A.; Aron, P. R.

1984-01-01

Silicon nitride and hafnium nitride coatings were deposited on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. The coatings and the interface between the coating and substrate were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. Oxide was found at all interfaces with an interface width of at least 600 A for the oxidized substrates and at least 300 A for the unoxidized substrates. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C. Coatings of both nitrides deposited at 8 mtorr were found to have increased adhesion to both oxidized and unoxidized 440C over those deposited at 20 mtorr.

Tensile and stress-rupture behavior of hafnium carbide dispersed molybdenum and tungsten base alloy wires

NASA Technical Reports Server (NTRS)

Yun, Hee Mann; Titran, Robert H.

1993-01-01

The tensile strain rate sensitivity and the stress-rupture strength of Mo-base and W-base alloy wires, 380 microns in diameter, were determined over the temperature range from 1200 K to 1600 K. Three molybdenum alloy wires; Mo + 1.1w/o hafnium carbide (MoHfC), Mo + 25w/o W + 1.1w/o hafnium carbide (MoHfC+25W) and Mo + 45w/o W + 1.1w/o hafnium carbide (MoHfC+45W), and a W + 0.4w/o hafnium carbide (WHfC) tungsten alloy wire were evaluated. The tensile strength of all wires studied was found to have a positive strain rate sensitivity. The strain rate dependency increased with increasing temperature and is associated with grain broadening of the initial fibrous structures. The hafnium carbide dispersed W-base and Mo-base alloys have superior tensile and stress-rupture properties than those without HfC. On a density compensated basis the MoHfC wires exhibit superior tensile and stress-rupture strengths to the WHfC wires up to approximately 1400 K. Addition of tungsten in the Mo-alloy wires was found to increase the long-term stress rupture strength at temperatures above 1400 K. Theoretical calculations indicate that the strength and ductility advantage of the HfC dispersed alloy wires is due to the resistance to recrystallization imparted by the dispersoid.

Mineral resource of the month: zirconium and hafnium

USGS Publications Warehouse

Gambogi, Joseph

2007-01-01

Zirconium and hafnium are corrosion-resistant metals that are grouped in the same family as titanium on the periodic table. The two elements commonly occur in oxide and silicate minerals and have significant economic importance in everything from ink, ceramics and golf shoes to nuclear fuel rods.

SEPARATING HAFNIUM FROM ZIRCONIUM

DOEpatents

Lister, B.A.J.; Duncan, J.F.; Hutcheon, J.M.

1956-08-21

Substantially complete separation of zirconium from hafnium may be obtained by elution of ion exchange material, on which compounds of the elements are adsorbed, with an approximately normal solution of sulfuric acid. Preferably the acid concentration is between 0.8 N amd 1.2 N, amd should not exceed 1.5 N;. Increasing the concentration of sulfate ion in the eluting solution by addition of a soluble sulfate, such as sodium sulfate, has been found to be advantageous. The preferred ion exchange materials are sulfonated polystyrene resins such as Dowex 50,'' and are preferably arranged in a column through which the solutions are passed.

Effect of cathode cooling efficiency and oxygen plasma gas pressure on the hafnium cathode wall temperature

NASA Astrophysics Data System (ADS)

Ashtekar, Koustubh; Diehl, Gregory; Hamer, John

2012-10-01

The hafnium cathode is widely used in DC plasma arc cutting (PAC) under an oxygen gas environment to cut iron and iron alloys. The hafnium erosion is always a concern which is controlled by the surface temperature. In this study, the effect of cathode cooling efficiency and oxygen gas pressure on the hafnium surface temperature are quantified. The two layer cathode sheath model is applied on the refractive hafnium surface while oxygen species (O2, O, O+, O++, e-) are considered within the thermal dis-equilibrium regime. The system of non-linear equations comprising of current density balance, heat flux balance at both the cathode surface and the sheath-ionization layer is coupled with the plasma gas composition solver. Using cooling heat flux, gas pressure and current density as inputs; the cathode wall temperature, electron temperature, and sheath voltage drop are calculated. Additionally, contribution of emitted electron current (Je) and ions current (Ji) to the total current flux are estimated. Higher gas pressure usually reduces Ji and increases Je that reduces the surface temperature by thermionic cooling.

21 CFR 186.1557 - Tall oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Tall oil. 186.1557 Section 186.1557 Food and Drugs... Substances Affirmed as GRAS § 186.1557 Tall oil. (a) Tall oil (CAS Reg. No. 8002-26-4) is essentially the sap... consists mainly of tall oil resin acids and tall oil fatty acids. (b) In accordance with § 186.1(b)(1), the...

21 CFR 186.1557 - Tall oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Tall oil. 186.1557 Section 186.1557 Food and Drugs... Substances Affirmed as GRAS § 186.1557 Tall oil. (a) Tall oil (CAS Reg. No. 8002-26-4) is essentially the sap... consists mainly of tall oil resin acids and tall oil fatty acids. (b) In accordance with § 186.1(b)(1), the...

21 CFR 186.1557 - Tall oil.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Tall oil. 186.1557 Section 186.1557 Food and Drugs... Substances Affirmed as GRAS § 186.1557 Tall oil. (a) Tall oil (CAS Reg. No. 8002-26-4) is essentially the sap... consists mainly of tall oil resin acids and tall oil fatty acids. (b) In accordance with § 186.1(b)(1), the...

21 CFR 186.1557 - Tall oil.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Tall oil. 186.1557 Section 186.1557 Food and Drugs... Substances Affirmed as GRAS § 186.1557 Tall oil. (a) Tall oil (CAS Reg. No. 8002-26-4) is essentially the sap... consists mainly of tall oil resin acids and tall oil fatty acids. (b) In accordance with § 186.1(b)(1), the...

Low-voltage bendable pentacene thin-film transistor with stainless steel substrate and polystyrene-coated hafnium silicate dielectric.

PubMed

Yun, Dong-Jin; Lee, Seunghyup; Yong, Kijung; Rhee, Shi-Woo

2012-04-01

The hafnium silicate and aluminum oxide high-k dielectrics were deposited on stainless steel substrate using atomic layer deposition process and octadecyltrichlorosilane (OTS) and polystyrene (PS) were treated improve crystallinity of pentacene grown on them. Besides, the effects of the pentacene deposition condition on the morphologies, crystallinities and electrical properties of pentacene were characterized. Therefore, the surface treatment condition on dielectric and pentacene deposition conditions were optimized. The pentacene grown on polystyrene coated high-k dielectric at low deposition rate and temperature (0.2-0.3 Å/s and R.T.) showed the largest grain size (0.8-1.0 μm) and highest crystallinity among pentacenes deposited various deposition conditions, and the pentacene TFT with polystyrene coated high-k dielectric showed excellent device-performance. To decrease threshold voltage of pentacene TFT, the polystyrene-thickness on high-k dielectric was controlled using different concentration of polystyrene solution. As the polystyrene-thickness on hafnium silicate decreases, the dielectric constant of polystyrene/hafnium silicate increases, while the crystallinity of pentacene grown on polystyrene/hafnium silicate did not change. Using low-thickness polystyrene coated hafnium silicate dielectric, the high-performance and low voltage operating (<5 V) pentacene thin film transistor (μ: ~2 cm(2)/(V s), on/off ratio, >1 × 10(4)) and complementary inverter (DC gains, ~20) could be fabricated.

Atomic layer deposition and characterization of hafnium oxide grown on silicon from tetrakis(diethylamino)hafnium and water vapor

NASA Astrophysics Data System (ADS)

Deshpande, Anand; Inman, Ronald; Jursich, Gregory; Takoudis, Christos

2004-09-01

In this work thin films of hafnium oxide are deposited on Si(100) substrates by means of atomic layer deposition (ALD) using tetrakis(diethylamino)hafnium and water vapor at substrate temperatures of 250-350ºC. Our system capabilities include fast transient delivery of reactive fluids, real-time vapor phase detection (in situ tunable diode laser hygrometer), precursor thermochemical capabilities, and ppt level elemental analysis by inductive coupling plasma mass spectrometry. The composition, purity, and other properties of the films and resulting interfaces are determined using x-ray and Fourier transform infrared spectroscopies, Z-contrast imaging and electron energy loss spectroscopy in a scanning transmission electron microscope with A˚ scale resolution, and spectroscopic ellipsometry. The observed ALD rate is ~1.4 A˚ per cycle. The nonuniformity across the film is less than 4%. Negligible carbon contamination is found in the resulting stoichiometric films under all conditions studied. The pulse sequence was optimized to prevent disastrous particulate problems while still minimizing purge times. The film deposition is investigated as a function of substrate temperature and reagent pulsing characteristics. A mild inverse temperature dependence of the ALD rate is observed. The initial stage of the HfO2 growth is investigated in detail.

Review of anhydrous zirconium-hafnium separation techniques. Information circular/1984

DOE Office of Scientific and Technical Information (OSTI.GOV)

Skaggs, R.L.; Rogers, D.T.; Hunter, D.B.

1983-12-01

Sixteen nonaqueous techniques conceived to replace the current aqueous scheme for separating hafnium and zirconium tetrachlorides were reviewed and evaluated by the Bureau of Mines. The methods are divided into two classes: separation by fractional volatilization of the tetrachlorides, which takes advantage of the higher volatility of hafnium tetrachloride; and separation by chemical techniques, based on differences in chemical behavior of the two tetrachlorides. The criteria used to evaluate separation methods were temperature, pressure, separation factor per equilibrium stage, complexity, compatibility with existing technology, and potential for continuous operation. Three processes were selected as being most promising: (1) high-pressure distillation,more » (2) extractive distillation from a molten salt, and (3) preferential reduction of gaseous ZrCl4. Any of the proposed nonaqueous Hf-Zr separation schemes must be supplemented with additional purification to remove trace impurities.« less

49 CFR 572.186 - Abdomen assembly.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 49 Transportation 7 2013-10-01 2013-10-01 false Abdomen assembly. 572.186 Section 572.186... Test Dummy, 50th Percentile Adult Male § 572.186 Abdomen assembly. (a) The abdomen assembly (175-5000) is part of the dummy assembly shown in drawing 175-0000 including load sensors specified in § 572.189...

49 CFR 572.186 - Abdomen assembly.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 49 Transportation 7 2011-10-01 2011-10-01 false Abdomen assembly. 572.186 Section 572.186... Dummy, 50th Percentile Adult Male § 572.186 Abdomen assembly. (a) The abdomen assembly (175-5000) is part of the dummy assembly shown in drawing 175-0000 including load sensors specified in § 572.189(e...

49 CFR 572.186 - Abdomen assembly.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 49 Transportation 7 2012-10-01 2012-10-01 false Abdomen assembly. 572.186 Section 572.186... Dummy, 50th Percentile Adult Male § 572.186 Abdomen assembly. (a) The abdomen assembly (175-5000) is part of the dummy assembly shown in drawing 175-0000 including load sensors specified in § 572.189(e...

21 CFR 186.1750 - Sodium chlorite.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium chlorite. 186.1750 Section 186.1750 Food... of Specific Substances Affirmed as GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS... passing chlorine dioxide into a solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is...

21 CFR 186.1750 - Sodium chlorite.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium chlorite. 186.1750 Section 186.1750 Food... of Specific Substances Affirmed as GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS... passing chlorine dioxide into a solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is...

21 CFR 186.1750 - Sodium chlorite.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium chlorite. 186.1750 Section 186.1750 Food... of Specific Substances Affirmed as GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS... passing chlorine dioxide into a solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is...

21 CFR 186.1555 - Japan wax.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Japan wax. 186.1555 Section 186.1555 Food and Drugs... Substances Affirmed as GRAS § 186.1555 Japan wax. (a) Japan wax (CAS Reg. No. 8001-39-6), also known as Japan... fruits of the oriental sumac, Rhus succedanea (Japan, Taiwan, and Indo-China), R. vernicifera (Japan...

21 CFR 186.1750 - Sodium chlorite.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium chlorite. 186.1750 Section 186.1750 Food and... Substances Affirmed as GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS Reg. No. 7758-19-2... into a solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is used at levels from...

21 CFR 186.1797 - Sodium sulfate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium sulfate. 186.1797 Section 186.1797 Food and... Substances Affirmed as GRAS § 186.1797 Sodium sulfate. (a) Sodium sulfate (Na2SO4, CAS Reg. No. 7757-82-6... crystalline powder. It is prepared by the neutralization of sulfuric acid with sodium hydroxide. (b) The...

21 CFR 186.1750 - Sodium chlorite.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium chlorite. 186.1750 Section 186.1750 Food... GRAS § 186.1750 Sodium chlorite. (a) Sodium chlorite (NaCLO2, CAS Reg. No. 7758-19-2) exists as... solution of sodium hydroxide and hydrogen peroxide. (b) the ingredient is used at levels from 125 to 250...

21 CFR 186.1797 - Sodium sulfate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium sulfate. 186.1797 Section 186.1797 Food and... Substances Affirmed as GRAS § 186.1797 Sodium sulfate. (a) Sodium sulfate (Na2SO4, CAS Reg. No. 7757-82-6... crystalline powder. It is prepared by the neutralization of sulfuric acid with sodium hydroxide. (b) The...

21 CFR 186.1797 - Sodium sulfate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium sulfate. 186.1797 Section 186.1797 Food and... Substances Affirmed as GRAS § 186.1797 Sodium sulfate. (a) Sodium sulfate (Na2SO4, CAS Reg. No. 7757-82-6... crystalline powder. It is prepared by the neutralization of sulfuric acid with sodium hydroxide. (b) The...

21 CFR 186.1797 - Sodium sulfate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium sulfate. 186.1797 Section 186.1797 Food and... Substances Affirmed as GRAS § 186.1797 Sodium sulfate. (a) Sodium sulfate (Na2SO4, CAS Reg. No. 7757-82-6... crystalline powder. It is prepared by the neutralization of sulfuric acid with sodium hydroxide. (b) The...

Development and characterization of ultrathin hafnium titanates as high permittivity gate insulators

NASA Astrophysics Data System (ADS)

Li, Min

High permittivity or high-kappa materials are being developed for use as gate insulators for future ultrascaled metal oxide semiconductor field effect transistors (MOSFETs). Hafnium containing compounds are the leading candidates. Due to its moderate permittivity, however, it is difficult to achieve HfO2 gate structures with an EOT well below 1.0 nm. One approach to increase HfO2 permittivity is combining it with a very high-kappa material, such as TiO2. In this thesis, we systematically studied the electrical and physical characteristics of high-kappa hafnium titanates films as gate insulators. A series of HfxTi1-xO2 films with well-controlled composition were deposited using an MOCVD system. The physical properties of the films were analyzed using a variety of characterization techniques. X-ray micro diffraction indicates that the Ti-rich thin film is more immune to crystallization. TEM analysis showed that the thick stoichiometric HfTiO 4 film has an orthorhombic structure and large anisotropic grains. The C-V curves from the devices with the hafnium titanates films displayed relatively low hysteresis. In a certain composition range, the interfacial layer (IL) EOT and permittivity of HfxTi1-x O2 increases linearly with increasing Ti. The charge is negative for HfxTi1-xO2/IL and positive for Si/IL interface, and the magnitude increases as Hf increases. For ultra-thin films (less than 2 nm EOT), the leakage current increases with increasing HE Moreover, the Hf-rich sample has weaker temperature dependence of the current. In the MOSFET devices with the hafnium titanates films, normal transistor characteristics were observed, also electron mobility degradation. Next, we investigated the effects that different pre-deposition surface treatments, including HF dipping, NH3 surface nitridation, and HfO2 deposition, have on the electrical properties of hafnium titanates. Surface nitridation shows stronger effect than the thin HfO2 layer. The nitrided samples displayed a

21 CFR 186.1771 - Sodium palmitate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium palmitate. 186.1771 Section 186.1771 Food... GRAS § 186.1771 Sodium palmitate. (a) Sodium palmitate (C16H31O2Na, CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white to yellow powder. Commercially...

21 CFR 186.1771 - Sodium palmitate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium palmitate. 186.1771 Section 186.1771 Food... of Specific Substances Affirmed as GRAS § 186.1771 Sodium palmitate. (a) Sodium palmitate (C16H31O2Na, CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white...

21 CFR 186.1771 - Sodium palmitate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium palmitate. 186.1771 Section 186.1771 Food... of Specific Substances Affirmed as GRAS § 186.1771 Sodium palmitate. (a) Sodium palmitate (C16H31O2Na, CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white...

21 CFR 186.1756 - Sodium formate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium formate. 186.1756 Section 186.1756 Food and... Substances Affirmed as GRAS § 186.1756 Sodium formate. (a) Sodium formate (CHNaO2, CAS Reg. No. 141-53-7) is the sodium salt of formic acid. It is produced by the reaction of carbon monoxide with sodium...

21 CFR 186.1771 - Sodium palmitate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium palmitate. 186.1771 Section 186.1771 Food... of Specific Substances Affirmed as GRAS § 186.1771 Sodium palmitate. (a) Sodium palmitate (C16H31O2Na, CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white...

21 CFR 186.1771 - Sodium palmitate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium palmitate. 186.1771 Section 186.1771 Food... of Specific Substances Affirmed as GRAS § 186.1771 Sodium palmitate. (a) Sodium palmitate (C16H31O2Na, CAS Reg. No. 408-35-5) is the sodium salt of palmitic acid (hexadecanoic acid). It exists as a white...

21 CFR 186.1756 - Sodium formate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium formate. 186.1756 Section 186.1756 Food and... Substances Affirmed as GRAS § 186.1756 Sodium formate. (a) Sodium formate (CHNaO2, CAS Reg. No. 141-53-7) is the sodium salt of formic acid. It is produced by the reaction of carbon monoxide with sodium...

21 CFR 186.1756 - Sodium formate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium formate. 186.1756 Section 186.1756 Food and... Substances Affirmed as GRAS § 186.1756 Sodium formate. (a) Sodium formate (CHNaO2, CAS Reg. No. 141-53-7) is the sodium salt of formic acid. It is produced by the reaction of carbon monoxide with sodium...

21 CFR 186.1756 - Sodium formate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium formate. 186.1756 Section 186.1756 Food and... Substances Affirmed as GRAS § 186.1756 Sodium formate. (a) Sodium formate (CHNaO2, CAS Reg. No. 141-53-7) is the sodium salt of formic acid. It is produced by the reaction of carbon monoxide with sodium...

21 CFR 186.1093 - Sulfamic acid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sulfamic acid. 186.1093 Section 186.1093 Food and... Substances Affirmed as GRAS § 186.1093 Sulfamic acid. (a) Sulfamic acid (H3NO3S, CAS Reg. No. 5329-14-6) is a white crystalline solid manufactured from urea, sulfur trioxide, and sulfuric acid. It is soluble and...

21 CFR 186.1770 - Sodium oleate.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Sodium oleate. 186.1770 Section 186.1770 Food and... Substances Affirmed as GRAS § 186.1770 Sodium oleate. (a) Sodium oleate (C18H33O2Na, CAS Reg. No. 143-19-1) is the sodium salt of oleic acid (cis-9-octadecenoic acid). It exists as a white to yellowish powder...

21 CFR 186.1770 - Sodium oleate.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sodium oleate. 186.1770 Section 186.1770 Food and... Substances Affirmed as GRAS § 186.1770 Sodium oleate. (a) Sodium oleate (C18H33O2Na, CAS Reg. No. 143-19-1) is the sodium salt of oleic acid (cis-9-octadecenoic acid). It exists as a white to yellowish powder...

21 CFR 186.1770 - Sodium oleate.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sodium oleate. 186.1770 Section 186.1770 Food and... Substances Affirmed as GRAS § 186.1770 Sodium oleate. (a) Sodium oleate (C18H33O2Na, CAS Reg. No. 143-19-1) is the sodium salt of oleic acid (cis-9-octadecenoic acid). It exists as a white to yellowish powder...

21 CFR 186.1770 - Sodium oleate.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sodium oleate. 186.1770 Section 186.1770 Food and... Substances Affirmed as GRAS § 186.1770 Sodium oleate. (a) Sodium oleate (C18H33O2Na, CAS Reg. No. 143-19-1) is the sodium salt of oleic acid (cis-9-octadecenoic acid). It exists as a white to yellowish powder...

Evidence for oxygen vacancies movement during wake-up in ferroelectric hafnium oxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Starschich, S.; Böttger, U.; Menzel, S.

The wake-up effect which is observed in ferroelectric hafnium oxide is investigated in yttrium doped hafnium oxide prepared by chemical solution deposition. It can be shown that not the amount of cycles but the duration of the applied electrical field is essential for the wake-up. Temperature dependent wake-up cycling in a range of −160 °C to 100 °C reveals a strong temperature activation of the wake-up, which can be attributed to ion rearrangement during cycling. By using asymmetrical electrodes, resistive valence change mechanism switching can be observed coincident with ferroelectric switching. From the given results, it can be concluded that redistribution ofmore » oxygen vacancies is the origin of the wake-up effect.« less

Effect of hafnium doping on density of states in dual-target magnetron co-sputtering HfZnSnO thin film transistors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Huang, Chuan-Xin; Li, Jun, E-mail: SHUniverjunli@163.com; Fu, Yi-Zhou

2015-11-23

This study investigates the effect of hafnium doping on the density of states (DOSs) in HfZnSnO thin film transistors fabricated by dual-target magnetron co-sputtering system. The DOSs is extracted by temperature-dependent field-effect measurements, and they decrease from 1.1 × 10{sup 17} to 4.6 × 10{sup 16 }eV/cm{sup 3} with increasing the hafnium concentrations. The behavior of DOSs for the increasing hafnium concentration HfZnSnO thin film transistors can be confirmed by both the reduction of ΔV{sub T} under bias stress and the trapping charges calculated by capacitance voltage measurements. It suggests that the reduction in DOSs due to the hafnium doping is closely related with themore » bias stability and thermal stability.« less

40 CFR 18.6 - Method of Application.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 1 2014-07-01 2014-07-01 false Method of Application. 18.6 Section 18.6 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL ENVIRONMENTAL PROTECTION RESEARCH FELLOWSHIPS AND SPECIAL RESEARCH CONSULTANTS FOR ENVIRONMENTAL PROTECTION § 18.6 Method of...

21 CFR 186.1673 - Pulp.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Pulp. 186.1673 Section 186.1673 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...

21 CFR 186.1673 - Pulp.

Code of Federal Regulations, 2014 CFR

2014-04-01

... food packaging containers. (c) The ingredient is used in paper and paperboard made by conventional... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Pulp. 186.1673 Section 186.1673 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

Hafnium germanosilicate thin films for gate and capacitor dielectric applications: thermal stability studies

NASA Astrophysics Data System (ADS)

Addepalli, Swarna; Sivasubramani, Prasanna; El-Bouanani, Mohamed; Kim, Moon; Gnade, Bruce; Wallace, Robert

2003-03-01

The use of SiO_2-GeO2 mixtures in gate and capacitor dielectric applications is hampered by the inherent thermodynamic instability of germanium oxide. Studies to date have confirmed that germanium oxide is readily converted to elemental germanium [1,2]. In sharp contrast, germanium oxide is known to form stable compounds with transition metal oxides such as hafnium oxide (hafnium germanate, HfGeO_4) [3]. Thus, the incorporation of hafnium in SiO_2-GeO2 may be expected to enhance the thermal stability of germanium oxide via Hf-O-Ge bond formation. In addition, the introduction of a transition metal would simultaneously enhance the capacitance of the dielectric thereby permitting a thicker dielectric which reduces leakage current [4]. In this study, the thermal stability of PVD-grown hafnium germanosilicate (HfGeSiO) films was investigated. XPS, HR-TEM, C-V and I-V results of films after deposition and subsequent annealing treatments will be presented. The results indicate that the presence or formation of elemental germanium drastically affects the stability of the HfGeSiO films. This work is supported by DARPA through SPAWAR Grant No. N66001-00-1-8928, and the Texas Advanced Technology Program. References: [1] W. S. Liu, J .S. Chen, M.-A. Nicolet, V. Arbet-Engels, K. L. Wang, Journal of Applied Physics, 72, 4444 (1992), and, Applied Physics Letters, 62, 3321 (1993) [2] W. S. Liu, M. -A. Nicolet, H. -H. Park, B. -H. Koak, J. -W. Lee, Journal of Applied Physics, 78, 2631 (1995) [3] P. M. Lambert, Inorganic Chemistry, 37, 1352 (1998) [4] G. D. Wilk, R. M. Wallace and J. M. Anthony, Journal of Applied Physics, 89, 5243 (2001)

21 CFR 186.1673 - Pulp.

Code of Federal Regulations, 2011 CFR

2011-04-01

... for use as a constituent of food packaging containers. (c) The ingredient is used in paper and... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Pulp. 186.1673 Section 186.1673 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1673 - Pulp.

Code of Federal Regulations, 2013 CFR

2013-04-01

... for use as a constituent of food packaging containers. (c) The ingredient is used in paper and... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Pulp. 186.1673 Section 186.1673 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1673 - Pulp.

Code of Federal Regulations, 2012 CFR

2012-04-01

... for use as a constituent of food packaging containers. (c) The ingredient is used in paper and... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Pulp. 186.1673 Section 186.1673 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... Listing of Specific Substances Affirmed as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish... from fish, primarily menhaden, and secondarily herring or tuna. Hydrogenation of fish oils uses...

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... Listing of Specific Substances Affirmed as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish... from fish, primarily menhaden, and secondarily herring or tuna. Hydrogenation of fish oils uses...

Article having an improved platinum-aluminum-hafnium protective coating

NASA Technical Reports Server (NTRS)

Nagaraj, Bangalore Aswatha (Inventor); Williams, Jeffrey Lawrence (Inventor)

2005-01-01

An article protected by a protective coating has a substrate and a protective coating having an outer layer deposited upon the substrate surface and a diffusion zone formed by interdiffusion of the outer layer and the substrate. The protective coating includes platinum, aluminum, no more than about 2 weight percent hafnium, and substantially no silicon. The outer layer is substantially a single phase.

12 CFR 18.6 - Signature and attestation.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 1 2010-01-01 2010-01-01 false Signature and attestation. 18.6 Section 18.6 Banks and Banking COMPTROLLER OF THE CURRENCY, DEPARTMENT OF THE TREASURY DISCLOSURE OF FINANCIAL AND OTHER INFORMATION BY NATIONAL BANKS § 18.6 Signature and attestation. A duly authorized officer of the...

21 CFR 820.186 - Quality system record.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Quality system record. 820.186 Section 820.186...) MEDICAL DEVICES QUALITY SYSTEM REGULATION Records § 820.186 Quality system record. Each manufacturer shall maintain a quality system record (QSR). The QSR shall include, or refer to the location of, procedures and...

21 CFR 133.186 - Sap sago cheese.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... CONSUMPTION CHEESES AND RELATED CHEESE PRODUCTS Requirements for Specific Standardized Cheese and Related Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the...

21 CFR 133.186 - Sap sago cheese.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... CONSUMPTION CHEESES AND RELATED CHEESE PRODUCTS Requirements for Specific Standardized Cheese and Related Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the...

15 CFR 18.6 - Standards for awards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Standards for awards. 18.6 Section 18.6 Commerce and Foreign Trade Office of the Secretary of Commerce ATTORNEY'S FEES AND OTHER EXPENSES General Provisions § 18.6 Standards for awards. (a) A prevailing applicant may receive an award for fees...

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551... as GRAS § 186.1551 Hydrogenated fish oil. (a) Hydrogenated fish oil (CAS Reg. No. 91078-95-4) is a class of oils produced by partial hydrogenation of oils expressed from fish, primarily menhaden, and...

46 CFR 502.186 - Contents of memoranda.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 9 2013-10-01 2013-10-01 false Contents of memoranda. 502.186 Section 502.186 Shipping FEDERAL MARITIME COMMISSION GENERAL AND ADMINISTRATIVE PROVISIONS RULES OF PRACTICE AND PROCEDURE Shortened Procedure § 502.186 Contents of memoranda. The memorandum should contain concise arguments and fact, the same as would be offered if a formal...

46 CFR 502.186 - Contents of memoranda.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 9 2010-10-01 2010-10-01 false Contents of memoranda. 502.186 Section 502.186 Shipping FEDERAL MARITIME COMMISSION GENERAL AND ADMINISTRATIVE PROVISIONS RULES OF PRACTICE AND PROCEDURE Shortened Procedure § 502.186 Contents of memoranda. The memorandum should contain concise arguments and fact, the same as would be offered if a formal...

Hafnium-Based Bulk Metallic Glasses for Kinetic Energy Penetrators

DTIC Science & Technology

2004-12-01

uranium -based (DU) and tungsten- nickel -iron (W-Ni-Fe) composite kinetic energy (KE) munitions is primarily ascribed to their high densities (U: ρ...based on an invariant point identified in the hafnium- copper- nickel ternary system. They are denser than zirconium-based glass-forming compositions...depleted- uranium penetrators. 1. INTRODUCTION 1.1 Criterion for Effective Kinetic Energy Penetrator Performance The lethality of depleted

29 CFR 18.6 - Motions and requests.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 29 Labor 1 2011-07-01 2011-07-01 false Motions and requests. 18.6 Section 18.6 Labor Office of the... ADMINISTRATIVE LAW JUDGES General § 18.6 Motions and requests. (a) Generally. Any application for an order or any other request shall be made by motion which, unless made during a hearing or trial, shall be made in...

21 CFR 133.186 - Sap sago cheese.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Sap sago cheese. 133.186 Section 133.186 Food and... Products § 133.186 Sap sago cheese. (a) Description. (1) Sap sago cheese is the food prepared by the... method described in § 133.5. Sap sago cheese is not less than 5 months old. (2) One or more of the dairy...

Inter-diffusion of copper and hafnium as studied by x-ray photoelectron spectroscopy

NASA Astrophysics Data System (ADS)

Pearson, Justin; Chourasia, A. R.

The Cu/Hf interface has been characterized by x-ray photoelectron spectroscopy. Thin films (thicknesses ranging from 100 nm to 150 nm) of hafnium were deposited on a silicon substrate. About 80 nm of copper was then deposited on such samples. The e-beam method was used for the deposition. The samples were annealed for 30 min at temperatures of 100, 200, 300, 400, and 500°C. The inter-diffusion of copper and hafnium was investigated by sequential sputter depth profiling and x-ray photoelectron spectroscopy. The interdiffusion in each case was analyzed by the Matano-Boltzmann's procedure using the Fick's second law. The interdiffusion coefficients and the width of the interface as determined from the data have been correlated with the annealing temperature. Supported by Organized Research, TAMU-Commerce.

42 CFR 460.186 - PACE premiums.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 4 2011-10-01 2011-10-01 false PACE premiums. 460.186 Section 460.186 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE) PROGRAMS OF ALL-INCLUSIVE CARE FOR THE ELDERLY (PACE...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Clay (kaolin). 186.1256 Section 186.1256 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...)(1), the ingredient is used as an indirect human food ingredient with no limitation other than...

21 CFR 186.1093 - Sulfamic acid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Sulfamic acid. 186.1093 Section 186.1093 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...

21 CFR 186.1093 - Sulfamic acid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Sulfamic acid. 186.1093 Section 186.1093 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...

21 CFR 186.1093 - Sulfamic acid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Sulfamic acid. 186.1093 Section 186.1093 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...

The performance of hafnium and gadolinium self powered neutron detectors in the TREAT reactor

NASA Astrophysics Data System (ADS)

Imel, G. R.; Hart, P. R.

1996-05-01

The use of gadolinium and hafnium self powered neutron detectors in a transient reactor is described in this paper. The detectors were calibrated to the fission rate of U-235 using calibrated fission chambers; the calibration factors were tested in two reactors in steady state and found to be consistent. Calibration of the detectors in transient reactor conditions was done by using uranium wires that were analyzed by radiochemistry techniques to determine total fissions during the transient. This was correlated to the time-integrated current of the detectors during the transient. A temperature correction factor was derived to account for self-shielding effects in the hafnium and gadolinium detectors. The dynamic response of the detectors under transient conditions was studied, and found to be excellent.

21 CFR 186.1093 - Sulfamic acid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... practice of using this ingredient in the manufacture of paper and paperboard that contact food. (c) Prior... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sulfamic acid. 186.1093 Section 186.1093 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

21 CFR 186.1374 - Iron oxides.

Code of Federal Regulations, 2011 CFR

2011-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Iron oxides. 186.1374 Section 186.1374 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1300 - Ferric oxide.

Code of Federal Regulations, 2011 CFR

2011-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Ferric oxide. 186.1300 Section 186.1300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1374 - Iron oxides.

Code of Federal Regulations, 2010 CFR

2010-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Iron oxides. 186.1374 Section 186.1374 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1300 - Ferric oxide.

Code of Federal Regulations, 2010 CFR

2010-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ferric oxide. 186.1300 Section 186.1300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1374 - Iron oxides.

Code of Federal Regulations, 2012 CFR

2012-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Iron oxides. 186.1374 Section 186.1374 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1300 - Ferric oxide.

Code of Federal Regulations, 2013 CFR

2013-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Ferric oxide. 186.1300 Section 186.1300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1374 - Iron oxides.

Code of Federal Regulations, 2013 CFR

2013-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Iron oxides. 186.1374 Section 186.1374 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1300 - Ferric oxide.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) The ingredient is used as a constituent of paper and paperboard used for food packaging. (2) The... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Ferric oxide. 186.1300 Section 186.1300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

21 CFR 186.1555 - Japan wax.

Code of Federal Regulations, 2014 CFR

2014-04-01

... ingredient is used as a constituent of cotton and cotton fabrics used for dry food packaging. (2) The... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Japan wax. 186.1555 Section 186.1555 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

21 CFR 186.1316 - Formic acid.

Code of Federal Regulations, 2014 CFR

2014-04-01

... used for food packaging. (c) The ingredient is used at levels not to exceed good manufacturing practice... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Formic acid. 186.1316 Section 186.1316 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

21 CFR 186.1300 - Ferric oxide.

Code of Federal Regulations, 2012 CFR

2012-04-01

... food packaging. (2) The ingredient is used at levels not to exceed current good manufacturing practice... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Ferric oxide. 186.1300 Section 186.1300 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1374 - Iron oxides.

Code of Federal Regulations, 2014 CFR

2014-04-01

...) The ingredient is used as a constituent of paper and paperboard used for food packaging. (2) The... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Iron oxides. 186.1374 Section 186.1374 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) INDIRECT FOOD...

21 CFR 186.1316 - Formic acid.

Code of Federal Regulations, 2011 CFR

2011-04-01

... paper and paperboard used for food packaging. (c) The ingredient is used at levels not to exceed good... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Formic acid. 186.1316 Section 186.1316 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1316 - Formic acid.

Code of Federal Regulations, 2010 CFR

2010-04-01

... paper and paperboard used for food packaging. (c) The ingredient is used at levels not to exceed good... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Formic acid. 186.1316 Section 186.1316 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1316 - Formic acid.

Code of Federal Regulations, 2012 CFR

2012-04-01

... paper and paperboard used for food packaging. (c) The ingredient is used at levels not to exceed good... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Formic acid. 186.1316 Section 186.1316 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1316 - Formic acid.

Code of Federal Regulations, 2013 CFR

2013-04-01

... paper and paperboard used for food packaging. (c) The ingredient is used at levels not to exceed good... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Formic acid. 186.1316 Section 186.1316 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN...

21 CFR 186.1756 - Sodium formate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium formate. 186.1756 Section 186.1756 Food and....1756 Sodium formate. (a) Sodium formate (CHNaO2, CAS Reg. No. 141-53-7) is the sodium salt of formic acid. It is produced by the reaction of carbon monoxide with sodium hydroxide. (b) The ingredient is...

21 CFR 186.1797 - Sodium sulfate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium sulfate. 186.1797 Section 186.1797 Food and....1797 Sodium sulfate. (a) Sodium sulfate (Na2SO4, CAS Reg. No. 7757-82-6), also known as Glauber's salt... by the neutralization of sulfuric acid with sodium hydroxide. (b) The ingredient is used as a...

"Decarbonization" of an imino N-heterocyclic carbene via triple benzyl migration from hafnium

USDA-ARS?s Scientific Manuscript database

An imino N-heterocyclic carbene underwent three sequential benzyl migrations upon reaction with tetrabenzylhafnium, resulting in complete removal of the carbene carbon from the ligand. The resulting eneamido-amidinato hafnium complex showed alkene polymerization activity comparable to that of a prec...

21 CFR 186.1557 - Tall oil.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Tall oil. 186.1557 Section 186.1557 Food and Drugs....1557 Tall oil. (a) Tall oil (CAS Reg. No. 8002-26-4) is essentially the sap of the pine tree. It is obtained commercially from the waste liquors of pinewood pulp mills and consists mainly of tall oil resin...

21 CFR 186.1770 - Sodium oleate.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Sodium oleate. 186.1770 Section 186.1770 Food and....1770 Sodium oleate. (a) Sodium oleate (C18H33O2Na, CAS Reg. No. 143-19-1) is the sodium salt of oleic.... Commercially, sodium oleate is made by mixing and heating flaked sodium hydroxide and oleic acid. (b) In...

PROCESS OF RECOVERING ZIRCONIUM VALUES FROM HAFNIUM VALUES BY SOLVENT EXTRACTION WITH AN ALKYL PHOSPHATE

DOEpatents

Peppard, D.F.

1960-02-01

A process of separating hafnium nitrate from zirconium nitrate contained in a nitric acid solution by selectively. extracting the zirconium nitrate with a water-immiscible alkyl phosphate is reported.

Rhemium-186-monoaminemonoamidedithiol-conjugated bisphosphonate derivatives for bone pain palliation.

PubMed

Ogawa, Kazuma; Mukai, Takahiro; Arano, Yasushi; Otaka, Akira; Ueda, Masashi; Uehara, Tomoya; Magata, Yasuhiro; Hashimoto, Kazuyuki; Saji, Hideo

2006-05-01

To develop a radiopharmaceutical for the palliation of painful bone metastases based on the concept of bifunctional radiopharmaceuticals, we synthesized a bisphosphonate derivative labeled with rhenium-186 (186Re) that contains a hydroxyl group at the central carbon of its bisphosphonate structure, we attached a stable 186Re-MAMA chelate to the amino group of a 4-amino butylidene-bisphosphonate derivative [N-[2-[[4-[(4-hydroxy-4,4-diphosphonobutyl)amino]-4-oxobutyl]-2-thioethylamino]acetyl]-2-aminoethanethiolate] oxorhenium (V) (186Re-MAMA-HBP) and we investigated the effect of a hydroxyl group at the central carbon of its bisphosphonate structure on affinity for hydroxyapatite and on biodistribution by conducting a comparative study with [N-[2-[[3-(3,3-diphosphonopropylcarbamoyl)propyl]-2-thioethylamino]acetyl]-2-aminoethanethiolate] oxorhenium (V) (186Re-MAMA-BP). The precursor of 186Re-MAMA-HBP, trityl (Tr)-MAMA-HBP, was obtained by coupling a Tr-MAMA derivative to 4-amino-1-hydroxybutylidene-1,1-bisphosphonate. 186Re-MAMA-HBP was prepared by a reaction with 186ReO(4-) and SnCl2 in citrate buffer after the deprotection of the Tr groups of Tr-MAMA-HBP. After reversed-phase high-performance liquid chromatography, 186Re-MAMA-HBP had a radiochemical purity of over 95%. Compared with 186Re-MAMA-BP, 186Re-MAMA-HBP showed a greater affinity for hydroxyapatite beads in vitro and accumulated a significantly higher level in the femur in vivo. Thus, the introduction of a hydroxyl group into 186Re complex-conjugated bisphosphonates would be effective in enhancing accumulation in bones. These findings provide useful information on the design of bone-seeking therapeutic radiopharmaceuticals.

40 CFR 18.6 - Method of Application.

Code of Federal Regulations, 2010 CFR

2010-07-01

... RESEARCH FELLOWSHIPS AND SPECIAL RESEARCH CONSULTANTS FOR ENVIRONMENTAL PROTECTION § 18.6 Method of Application. Application for an Environmental Protection Research fellowship shall be made in accordance with... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Method of Application. 18.6 Section 18...

Ferroelectric memory based on molybdenum disulfide and ferroelectric hafnium oxide

NASA Astrophysics Data System (ADS)

Yap, Wui Chung; Jiang, Hao; Xia, Qiangfei; Zhu, Wenjuan

Recently, ferroelectric hafnium oxide (HfO2) was discovered as a new type of ferroelectric material with the advantages of high coercive field, excellent scalability (down to 2.5 nm), and good compatibility with CMOS processing. In this work, we demonstrate, for the first time, 2D ferroelectric memories with molybdenum disulfide (MoS2) as the channel material and aluminum doped HfO2 as the ferroelectric gate dielectric. A 16 nm thick layer of HfO2, doped with 5.26% aluminum, was deposited via atomic layer deposition (ALD), then subjected to rapid thermal annealing (RTA) at 1000 °C, and the polarization-voltage characteristics of the resulting metal-ferroelectric-metal (MFM) capacitors were measured, showing a remnant polarization of 0.6 μC/cm2. Ferroelectric memories with embedded ferroelectric hafnium oxide stacks and monolayer MoS2 were fabricated. The transfer characteristics after program and erase pulses revealed a clear ferroelectric memory window. In addition, endurance (up to 10,000 cycles) of the devices were tested and effects associated with ferroelectric materials, such as the wake-up effect and polarization fatigue, were observed. This research can potentially lead to advances of 2D materials in low-power logic and memory applications.

Scale-up of high specific activity 186gRe production using graphite-encased thick 186W targets and demonstration of an efficient target recycling process

DOE PAGES

Balkin, Ethan R.; Gagnon, Katherine; Dorman, Eric; ...

2017-08-18

Production of high specific activity 186gRe is of interest for development of theranostic radiopharmaceuticals. Previous studies have shown that high specific activity 186gRe can be obtained by cyclotron irradiation of enriched 186W via the 186W(d,2n) 186gRe reaction, but most irradiations were conducted at low beam currents and for short durations. In this paper, enriched 186W metal targets were irradiated at high incident deuteron beam currents to demonstrate production rates and contaminants produced when using thick targets. Full-stopping thick targets, as determined using SRIM, were prepared by uniaxial pressing of powdered natural abundance W metal or 96.86% enriched 186W metal encasedmore » between two layers of graphite flakes for target material stabilization. An assessment of structural integrity was made on each target preparation. To assess the performance of graphite-encased thick 186W metal targets, along with the impact of encasing on the separation chemistry, targets were first irradiated using a 22 MeV deuteron beam for 10 min at 10, 20, and 27 μA, with an estimated nominal deuteron energy of 18.7 MeV on the 186W target material (after energy degradation correction from top graphite layer). Gamma-ray spectrometry was performed post EOB on all targets to assess production yields and radionuclidic byproducts. The investigation also evaluated a method to recover and recycle enriched target material from a column isolation procedure. Material composition analyses of target materials, pass-through/wash solutions and recycling process isolates were conducted with SEM, FTIR, XRD, EDS and ICP-MS spectrometry. Finally, to demonstrate scaled-up production, a graphite-encased 186W target made from recycled 186W was irradiated for ~2 h with 18.7 MeV deuterons at a beam current of 27 μA to provide 0.90 GBq (24.3 mCi) of 186gRe, decay-corrected to the end of bombardment. ICP-MS analysis of the isolated 186gRe solution provided data that indicated the

Scale-up of high specific activity 186gRe production using graphite-encased thick 186W targets and demonstration of an efficient target recycling process

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balkin, Ethan R.; Gagnon, Katherine; Dorman, Eric

Production of high specific activity 186gRe is of interest for development of theranostic radiopharmaceuticals. Previous studies have shown that high specific activity 186gRe can be obtained by cyclotron irradiation of enriched 186W via the 186W(d,2n) 186gRe reaction, but most irradiations were conducted at low beam currents and for short durations. In this paper, enriched 186W metal targets were irradiated at high incident deuteron beam currents to demonstrate production rates and contaminants produced when using thick targets. Full-stopping thick targets, as determined using SRIM, were prepared by uniaxial pressing of powdered natural abundance W metal or 96.86% enriched 186W metal encasedmore » between two layers of graphite flakes for target material stabilization. An assessment of structural integrity was made on each target preparation. To assess the performance of graphite-encased thick 186W metal targets, along with the impact of encasing on the separation chemistry, targets were first irradiated using a 22 MeV deuteron beam for 10 min at 10, 20, and 27 μA, with an estimated nominal deuteron energy of 18.7 MeV on the 186W target material (after energy degradation correction from top graphite layer). Gamma-ray spectrometry was performed post EOB on all targets to assess production yields and radionuclidic byproducts. The investigation also evaluated a method to recover and recycle enriched target material from a column isolation procedure. Material composition analyses of target materials, pass-through/wash solutions and recycling process isolates were conducted with SEM, FTIR, XRD, EDS and ICP-MS spectrometry. Finally, to demonstrate scaled-up production, a graphite-encased 186W target made from recycled 186W was irradiated for ~2 h with 18.7 MeV deuterons at a beam current of 27 μA to provide 0.90 GBq (24.3 mCi) of 186gRe, decay-corrected to the end of bombardment. ICP-MS analysis of the isolated 186gRe solution provided data that indicated the

21 CFR 186.1551 - Hydrogenated fish oil.

Code of Federal Regulations, 2011 CFR

2011-04-01

... used for dry food packaging. (d) The ingredient is used at levels not to exceed good manufacturing... 21 Food and Drugs 3 2011-04-01 2011-04-01 false Hydrogenated fish oil. 186.1551 Section 186.1551 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD...

50 CFR 622.186 - Landing fish intact.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 50 Wildlife and Fisheries 12 2013-10-01 2013-10-01 false Landing fish intact. 622.186 Section 622...-Grouper Fishery of the South Atlantic Region § 622.186 Landing fish intact. (a) South Atlantic snapper... specified in paragraph (b) of this section. Such fish may be eviscerated, gilled, and scaled, but must...

50 CFR 622.186 - Landing fish intact.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 50 Wildlife and Fisheries 12 2014-10-01 2014-10-01 false Landing fish intact. 622.186 Section 622...-Grouper Fishery of the South Atlantic Region § 622.186 Landing fish intact. (a) South Atlantic snapper... specified in paragraph (b) of this section. Such fish may be eviscerated, gilled, and scaled, but must...

Accelerator Production and Separations for High Specific Activity Rhenium-186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jurisson, Silvia S.; Wilbur, D. Scott

2016-04-01

Tungsten and osmium targets were evaluated for the production of high specific activity rhenium-186. Rhenium-186 has potential applications in radiotherapy for the treatment of a variety of diseases, including targeting with monoclonal antibodies and peptides. Methods were evaluated using tungsten metal, tungsten dioxide, tungsten disulfide and osmium disulfide. Separation of the rhenium-186 produced and recycling of the enriched tungsten-186 and osmium-189 enriched targets were developed.

Hafnium nitride buffer layers for growth of GaN on silicon

DOEpatents

Armitage, Robert D.; Weber, Eicke R.

2005-08-16

Gallium nitride is grown by plasma-assisted molecular-beam epitaxy on (111) and (001) silicon substrates using hafnium nitride buffer layers. Wurtzite GaN epitaxial layers are obtained on both the (111) and (001) HfN/Si surfaces, with crack-free thickness up to 1.2 {character pullout}m. However, growth on the (001) surface results in nearly stress-free films, suggesting that much thicker crack-free layers could be obtained.

Studies on Optical and Electrical Properties of Hafnium Oxide Nanoparticles

NASA Astrophysics Data System (ADS)

Jayaraman, Venkatachalam; Sagadevan, Suresh; Sudhakar, Rajesh

2017-07-01

In this paper, the synthesis and physico-chemical properties of hafnium oxide nanoparticles (HfO2 NPs) are analyzed and reported. The synthesis was carried out by the precipitation route by using hafnium tetrachloride (HfCl4) as precursor material with potassium hydroxide (KOH) dissolved in Millipore water. In the precipitation technique, the chemical reaction is comparatively simple, low-cost and non-toxic compared to other synthetic methods. The synthesized HfO2 NPs were characterized by using powder x-ray diffraction (PXRD), ultraviolet-visible (UV-Vis) spectroscopy, Raman analysis, and high-resolution transmission electron microscopy (HRTEM). The monoclinic structure of the HfO2 NPs was resolved utilizing x-ray diffraction (XRD). The optical properties were studied from the UV-Vis absorption spectrum. The optical band gap of the HfO2NPs was observed to be 5.1 eV. The Raman spectrum shows the presence of HfO2 NPs. The HRTEM image showed that the HfO2 NPs were of spherical shape with an average particle size of around 28 nm. The energy-dispersive x-ray spectroscopy (EDS) spectrum obviously demonstrated the presence of HfO2 NPs. Analysis and studies on the dielectric properties of the HfO2 NPs such as the dielectric constant, the dielectric loss, and alternating current (AC) conductivity were carried out at varying frequencies and temperatures.

Bulk production and evaluation of high specific activity 186g Re for cancer therapy using enriched 186 WO 3 targets in a proton beam

DOE PAGES

Mastren, Tara; Radchenko, Valery; Bach, Hong T.; ...

2017-06-01

Rhenium-186 g (t 1/2 = 3.72 d) is a β– emitting isotope suitable for theranostic applications. Current production methods rely on reactor production by way of the reaction 185Re(n,γ) 186gRe, which results in low specific activities limiting its use for cancer therapy. Production via charged particle activation of enriched 186W results in a 186gRe product with a much specific activity, allowing it to be used more broadly for targeted radiotherapy applications. Furthermore, this targets the unmet clinical need for more efficient radiotherapeutics.

Bulk production and evaluation of high specific activity 186g Re for cancer therapy using enriched 186 WO 3 targets in a proton beam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mastren, Tara; Radchenko, Valery; Bach, Hong T.

Rhenium-186 g (t 1/2 = 3.72 d) is a β– emitting isotope suitable for theranostic applications. Current production methods rely on reactor production by way of the reaction 185Re(n,γ) 186gRe, which results in low specific activities limiting its use for cancer therapy. Production via charged particle activation of enriched 186W results in a 186gRe product with a much specific activity, allowing it to be used more broadly for targeted radiotherapy applications. Furthermore, this targets the unmet clinical need for more efficient radiotherapeutics.

50 CFR 300.186 - Completed and approved documents.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 50 Wildlife and Fisheries 7 2010-10-01 2010-10-01 false Completed and approved documents. 300.186 Section 300.186 Wildlife and Fisheries INTERNATIONAL FISHING AND RELATED ACTIVITIES INTERNATIONAL FISHERIES REGULATIONS International Trade Documentation and Tracking Programs for Highly Migratory Species...

50 CFR 300.186 - Completed and approved documents.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 50 Wildlife and Fisheries 9 2011-10-01 2011-10-01 false Completed and approved documents. 300.186 Section 300.186 Wildlife and Fisheries INTERNATIONAL FISHING AND RELATED ACTIVITIES INTERNATIONAL FISHERIES REGULATIONS International Trade Documentation and Tracking Programs for Highly Migratory Species...

Hafnium isotope evidence for a transition in the dynamics of continental growth 3.2 Gyr ago.

PubMed

Næraa, T; Scherstén, A; Rosing, M T; Kemp, A I S; Hoffmann, J E; Kokfelt, T F; Whitehouse, M J

2012-05-30

Earth's lithosphere probably experienced an evolution towards the modern plate tectonic regime, owing to secular changes in mantle temperature. Radiogenic isotope variations are interpreted as evidence for the declining rates of continental crustal growth over time, with some estimates suggesting that over 70% of the present continental crustal reservoir was extracted by the end of the Archaean eon. Patterns of crustal growth and reworking in rocks younger than three billion years (Gyr) are thought to reflect the assembly and break-up of supercontinents by Wilson cycle processes and mark an important change in lithosphere dynamics. In southern West Greenland numerous studies have, however, argued for subduction settings and crust growth by arc accretion back to 3.8 Gyr ago, suggesting that modern-day tectonic regimes operated during the formation of the earliest crustal rock record. Here we report in situ uranium-lead, hafnium and oxygen isotope data from zircons of basement rocks in southern West Greenland across the critical time period during which modern-like tectonic regimes could have initiated. Our data show pronounced differences in the hafnium isotope-time patterns across this interval, requiring changes in the characteristics of the magmatic protolith. The observations suggest that 3.9-3.5-Gyr-old rocks differentiated from a >3.9-Gyr-old source reservoir with a chondritic to slightly depleted hafnium isotope composition. In contrast, rocks formed after 3.2 Gyr ago register the first additions of juvenile depleted material (that is, new mantle-derived crust) since 3.9 Gyr ago, and are characterized by striking shifts in hafnium isotope ratios similar to those shown by Phanerozoic subduction-related orogens. These data suggest a transitional period 3.5-3.2 Gyr ago from an ancient (3.9-3.5 Gyr old) crustal evolutionary regime unlike that of modern plate tectonics to a geodynamic setting after 3.2 Gyr ago that involved juvenile crust generation by plate

31 CFR 103.186 - Special measures against Burma.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 31 Money and Finance: Treasury 1 2010-07-01 2010-07-01 false Special measures against Burma. 103.186 Section 103.186 Money and Finance: Treasury Regulations Relating to Money and Finance FINANCIAL RECORDKEEPING AND REPORTING OF CURRENCY AND FOREIGN TRANSACTIONS Anti-Money Laundering Programs Law Enforcement...

5 CFR 550.186 - Relationship to other payments.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Section 550.186 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY ADMINISTRATION (GENERAL) Premium Pay Law Enforcement Availability Pay § 550.186 Relationship to other payments... retirement benefits; and (8) For any other purposes explicitly provided for by law or as the Office of...

5 CFR 550.186 - Relationship to other payments.

Code of Federal Regulations, 2013 CFR

2013-01-01

... Section 550.186 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY ADMINISTRATION (GENERAL) Premium Pay Law Enforcement Availability Pay § 550.186 Relationship to other payments... retirement benefits; and (8) For any other purposes explicitly provided for by law or as the Office of...

5 CFR 550.186 - Relationship to other payments.

Code of Federal Regulations, 2012 CFR

2012-01-01

... Section 550.186 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY ADMINISTRATION (GENERAL) Premium Pay Law Enforcement Availability Pay § 550.186 Relationship to other payments... retirement benefits; and (8) For any other purposes explicitly provided for by law or as the Office of...

5 CFR 550.186 - Relationship to other payments.

Code of Federal Regulations, 2014 CFR

2014-01-01

... Section 550.186 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY ADMINISTRATION (GENERAL) Premium Pay Law Enforcement Availability Pay § 550.186 Relationship to other payments... retirement benefits; and (8) For any other purposes explicitly provided for by law or as the Office of...

5 CFR 550.186 - Relationship to other payments.

Code of Federal Regulations, 2011 CFR

2011-01-01

... Section 550.186 Administrative Personnel OFFICE OF PERSONNEL MANAGEMENT CIVIL SERVICE REGULATIONS PAY ADMINISTRATION (GENERAL) Premium Pay Law Enforcement Availability Pay § 550.186 Relationship to other payments... retirement benefits; and (8) For any other purposes explicitly provided for by law or as the Office of...

Slow DNA Transport through Nanopores in Hafnium Oxide Membranes

PubMed Central

Bell, David C.; Cohen-Karni, Tzahi; Rosenstein, Jacob K.; Wanunu, Meni

2016-01-01

We present a study of double- and single-stranded DNA transport through nanopores fabricated in ultrathin (2–7 nm thick) free-standing hafnium oxide (HfO2) membranes. The high chemical stability of ultrathin HfO2 enables long-lived experiments with <2 nm diameter pores that last several hours, in which we observe >50 000 DNA translocations with no detectable pore expansion. Mean DNA velocities are slower than velocities through comparable silicon nitride pores, providing evidence that HfO2 nanopores have favorable physicochemical interactions with nucleic acids that can be leveraged to slow down DNA in a nanopore. PMID:24083444

28 CFR 115.186 - Sexual abuse incident reviews.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 28 Judicial Administration 2 2014-07-01 2014-07-01 false Sexual abuse incident reviews. 115.186... NATIONAL STANDARDS Standards for Lockups Data Collection and Review § 115.186 Sexual abuse incident reviews. (a) The lockup shall conduct a sexual abuse incident review at the conclusion of every sexual abuse...

28 CFR 115.186 - Sexual abuse incident reviews.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 28 Judicial Administration 2 2012-07-01 2012-07-01 false Sexual abuse incident reviews. 115.186... NATIONAL STANDARDS Standards for Lockups Data Collection and Review § 115.186 Sexual abuse incident reviews. (a) The lockup shall conduct a sexual abuse incident review at the conclusion of every sexual abuse...

28 CFR 115.186 - Sexual abuse incident reviews.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 28 Judicial Administration 2 2013-07-01 2013-07-01 false Sexual abuse incident reviews. 115.186... NATIONAL STANDARDS Standards for Lockups Data Collection and Review § 115.186 Sexual abuse incident reviews. (a) The lockup shall conduct a sexual abuse incident review at the conclusion of every sexual abuse...

Cathodoluminescence Study of Hafnium Oxide

NASA Astrophysics Data System (ADS)

Purcell, Emily; Hengehold, Robert; McClory, John

2011-10-01

Hafnium dioxide (HfO2) is increasingly being used in place of silicon oxide as a gate insulator in field effect transistors. This is primarily due to its high dielectric constant, κ, of 25. Samples of HfO2 were grown by either atomic layer deposition (ALD) or pulsed laser deposition (PLD), with the PLD samples having assorted substrate temperatures during deposition (300 C, 500 C, and 750 C). Cathodoluminescence (CL) was chosen as the technique used for studying these HfO2 samples. The CL system used was capable of beam energies ranging from 1 keV to 20 keV and beam currents ranging from 10 μA to 50 μA. A Monte Carlo calculation using CASINO software was performed in order to determine the beam energy for the desired depth of penetration. Measurements were taken at sample temperatures ranging from 7K (closed cycled cryostat) to 300K (room temperature), as well as at various beam energies and beam currents. Comparison will be made between the PLD and ALD spectra.

Estimation of continental 187Os/186Os values by using 187Os/186Os and 143Nd/144Nd ratios in marine manganese nodules

PubMed Central

Turekian, Karl K.; Luck, Jean-Marc

1984-01-01

The relationship between 187Os/186Os and 143Nd/144Nd in different manganese nodule fields is used to determine the 187Os/186Os ratio of the continental terrains bounding the major ocean basins. The Atlantic Ocean drainages yield 187Os/186Os of about 11; the Pacific Ocean, between 25 and 36; and the western Indian Ocean, 20. By assuming a two-component continental crust composed of “ultramafic rocks” (high Os concentration, low 187Os/186Os) and “granite” with only radiogenic 187Os produced in accessory Re-bearing molybdenite, the ultramafic contribution to weathering is about 0.2%. Some or most of this may come from the alteration of oceanic ultramafics. PMID:16578780

Self-cleaning and surface chemical reactions during hafnium dioxide atomic layer deposition on indium arsenide.

PubMed

Timm, Rainer; Head, Ashley R; Yngman, Sofie; Knutsson, Johan V; Hjort, Martin; McKibbin, Sarah R; Troian, Andrea; Persson, Olof; Urpelainen, Samuli; Knudsen, Jan; Schnadt, Joachim; Mikkelsen, Anders

2018-04-12

Atomic layer deposition (ALD) enables the ultrathin high-quality oxide layers that are central to all modern metal-oxide-semiconductor circuits. Crucial to achieving superior device performance are the chemical reactions during the first deposition cycle, which could ultimately result in atomic-scale perfection of the semiconductor-oxide interface. Here, we directly observe the chemical reactions at the surface during the first cycle of hafnium dioxide deposition on indium arsenide under realistic synthesis conditions using photoelectron spectroscopy. We find that the widely used ligand exchange model of the ALD process for the removal of native oxide on the semiconductor and the simultaneous formation of the first hafnium dioxide layer must be significantly revised. Our study provides substantial evidence that the efficiency of the self-cleaning process and the quality of the resulting semiconductor-oxide interface can be controlled by the molecular adsorption process of the ALD precursors, rather than the subsequent oxide formation.

Chemoradionuclide Therapy with 186Re-Labeled Liposomal Doxorubicin: Toxicity, Dosimetry, and Therapeutic Response

PubMed Central

Soundararajan, Anuradha; Bao, Ande; Phillips, William T.; McManus, Linda M.

2011-01-01

Abstract This study was performed to determine the maximum tolerated dose (MTD) and therapeutic effects of rhenium-186 (186Re)-labeled liposomal doxorubicin (Doxil), investigate associated toxicities, and calculate radiation absorbed dose in head and neck tumor xenografts and normal organs. Doxil and control polyethylene glycol (PEG)-liposomes were labeled using 186Re-N,N-bis(2-mercaptoethyl)-N′,N′-diethylethylenediamine (BMEDA) method. Tumor-bearing rats received either no therapy (n=6), intravenous Doxil (n=4), or escalating radioactivity of 186Re-Doxil (185–925 MBq/kg) or 186Re-PEG-liposomes (1110–1665 MBq/kg) and were monitored for 28 days. Based on body weight loss and systemic toxicity, MTD for 186Re-Doxil and 186Re-PEG-liposomes were established at injected radioactivity/body weight of 740 and 1480 MBq/kg, respectively. 186Re-injected radioactivity/body weight for therapy studies was determined to be 555 MBq/kg for 186Re-Doxil and 1295 MBq/kg for 186Re-PEG-liposomes. All groups recovered from their body weight loss, leucopenia, and thrombocytopenia by 28 days postinjection. Normalized radiation absorbed dose to tumor was significantly higher for 186Re-Doxil (0.299±0.109 Gy/MBq) compared with 186Re-PEG-liposomes (0.096±0.120 Gy/MBq) (p<0.05). In a separate therapy study, tumor volumes were significantly smaller for 186Re-Doxil (555 MBq/kg) compared with 186Re-PEG-liposomes (1295 MBq/kg) (p<0.01) at 42 days postinjection. In conclusion, combination chemoradionuclide therapy with 186Re-Doxil has promising potential, because good tumor control was achieved with limited associated toxicity. PMID:21834653

40 CFR 96.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Trading Program. 96.186 Section 96.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR NOX Opt-in Units § 96.186 Withdrawal from CAIR NOX Annual Trading...

40 CFR 96.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Trading Program. 96.186 Section 96.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR NOX Opt-in Units § 96.186 Withdrawal from CAIR NOX Annual Trading...

40 CFR 96.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Trading Program. 96.186 Section 96.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO 2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR NOX Opt-in Units § 96.186 Withdrawal from CAIR NOX Annual Trading...

40 CFR 96.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Trading Program. 96.186 Section 96.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR NOX Opt-in Units § 96.186 Withdrawal from CAIR NOX Annual Trading...

40 CFR 96.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Trading Program. 96.186 Section 96.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS FOR STATE IMPLEMENTATION PLANS CAIR NOX Opt-in Units § 96.186 Withdrawal from CAIR NOX Annual Trading...

40 CFR 97.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Trading Program. 97.186 Section 97.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR NOX Opt-In Units § 97.186 Withdrawal from CAIR NOX Annual Trading Program. Except as provided...

40 CFR 97.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Trading Program. 97.186 Section 97.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR NOX Opt-In Units § 97.186 Withdrawal from CAIR NOX Annual Trading Program. Except as provided...

40 CFR 97.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Trading Program. 97.186 Section 97.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR NOX Opt-In Units § 97.186 Withdrawal from CAIR NOX Annual Trading Program. Except as provided...

40 CFR 97.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Trading Program. 97.186 Section 97.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR NOX Opt-In Units § 97.186 Withdrawal from CAIR NOX Annual Trading Program. Except as provided...

40 CFR 97.186 - Withdrawal from CAIR NOX Annual Trading Program.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Trading Program. 97.186 Section 97.186 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) FEDERAL NOX BUDGET TRADING PROGRAM AND CAIR NOX AND SO2 TRADING PROGRAMS CAIR NOX Opt-In Units § 97.186 Withdrawal from CAIR NOX Annual Trading Program. Except as provided...

Aminopyridinate-FI hybrids, their hafnium and titanium complexes, and their application in the living polymerization of 1-hexene.

PubMed

Haas, Isabelle; Dietel, Thomas; Press, Konstantin; Kol, Moshe; Kempe, Rhett

2013-10-11

Based on two well-established ligand systems, the aminopyridinato (Ap) and the phenoxyimine (FI) ligand systems, new Ap-FI hybrid ligands were developed. Four different Ap-FI hybrid ligands were synthesized through a simple condensation reaction and fully characterized. The reaction of hafnium tetrabenzyl with all four Ap-FI hybrid ligands exclusively led to mono(Ap-FI) complexes of the type [(Ap-FI)HfBn2 ]. The ligands acted as tetradentate dianionic chelates. Upon activation with tris(pentafluorophenyl)borane, the hafnium-dibenzyl complexes led to highly active catalysts for the polymerization of 1-hexene. Ultrahigh molecular weights and extremely narrow polydispersities support the living nature of this polymerization process. A possible deactivation product of the hafnium catalysts was characterized by single-crystal X-ray analysis and is discussed. The coordination modes of these new ligands were studied with the help of model titanium complexes. The reaction of titanium(IV) isopropoxide with ligand 1 led to a mono(Ap-FI) complex, which showed the desired fac-mer coordination mode. Titanium (IV) isopropoxide reacted with ligand 4 to give a complex of the type [(ApH-FI)2 Ti(OiPr)2 ], which featured the ligand in its monoanionic form. The two titanium complexes were characterized by X-ray crystal-structure analysis. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

27 CFR 53.186 - Accounting procedures for like articles.

Code of Federal Regulations, 2014 CFR

2014-04-01

... like articles. 53.186 Section 53.186 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Accounting procedures for like articles. (a) Identification of manufacturer. In applying section 6416 of the Code and the regulations thereunder, a person who has purchased like articles from various...

27 CFR 53.186 - Accounting procedures for like articles.

Code of Federal Regulations, 2011 CFR

2011-04-01

... like articles. 53.186 Section 53.186 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Accounting procedures for like articles. (a) Identification of manufacturer. In applying section 6416 of the Code and the regulations thereunder, a person who has purchased like articles from various...

27 CFR 53.186 - Accounting procedures for like articles.

Code of Federal Regulations, 2013 CFR

2013-04-01

... like articles. 53.186 Section 53.186 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Accounting procedures for like articles. (a) Identification of manufacturer. In applying section 6416 of the Code and the regulations thereunder, a person who has purchased like articles from various...

27 CFR 53.186 - Accounting procedures for like articles.

Code of Federal Regulations, 2010 CFR

2010-04-01

... like articles. 53.186 Section 53.186 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND... Accounting procedures for like articles. (a) Identification of manufacturer. In applying section 6416 of the Code and the regulations thereunder, a person who has purchased like articles from various...

Processing and characterization of boron carbide-hafnium diboride ceramics

NASA Astrophysics Data System (ADS)

Brown-Shaklee, Harlan James

Hafnium diboride based ceramics are promising candidate materials for advanced aerospace and nuclear reactor components. The effectiveness of boron carbide and carbon as HfB2 sintering additives was systematically evaluated. In the first stage of the research, boron carbide and carbon additives were found to improve the densification behavior of milled HfB2 powder in part by removing oxides at the HfB2 surface during processing. Boron carbide additives reduced the hot pressing temperature of HfB2 by 150°C compared to carbon, which reduced the hot pressing temperature by ˜50°C. Reduction of oxide impurities alone could not explain the difference in sintering enhancement, however, and other mechanisms of enhancement were evaluated. Boron carbides throughout the homogeneity range were characterized to understand other mechanisms of sintering enhancement in HfB2. Heavily faulted carbon rich and boron rich boron carbides were synthesized for addition to HfB2. The greatest enhancement to densification was observed in samples containing boron- and carbon-rich compositions whereas B6.5 C provided the least enhancement to densification. It is proposed that carbon rich and boron rich boron carbides create boron and hafnium point defects in HfB2, respectively, which facilitate densification. Evaluation of the thermal conductivity (kth) between room temperature and 2000°C suggested that the stoichiometry of the boron carbide additives did not significantly affect kth of HfB2-BxC composites. The improved sinterability and the high kth (˜110 W/m-K at 300K and ˜90 W/m-K at 1000°C ) of HfB2-BxC ceramics make them excellent candidates for isotopically enriched reactor control materials.

21 CFR 211.186 - Master production and control records.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 21 Food and Drugs 4 2014-04-01 2014-04-01 false Master production and control records. 211.186... Reports § 211.186 Master production and control records. (a) To assure uniformity from batch to batch, master production and control records for each drug product, including each batch size thereof, shall be...

21 CFR 211.186 - Master production and control records.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 21 Food and Drugs 4 2012-04-01 2012-04-01 false Master production and control records. 211.186... Reports § 211.186 Master production and control records. (a) To assure uniformity from batch to batch, master production and control records for each drug product, including each batch size thereof, shall be...

21 CFR 211.186 - Master production and control records.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 21 Food and Drugs 4 2013-04-01 2013-04-01 false Master production and control records. 211.186... Reports § 211.186 Master production and control records. (a) To assure uniformity from batch to batch, master production and control records for each drug product, including each batch size thereof, shall be...

miR-186 inhibits cell proliferation in multiple myeloma by repressing Jagged1

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Zengyan; Department of Hematology, Hospital Affiliated to Binzhou Medical University, 661 Second Huanghe Street, Binzhou 256603; Zhang, Guoqiang

2016-01-15

MicroRNAs (miRNAs) are small, noncoding ribonucleic acids that regulate gene expression by targeting mRNAs for translational repression and degradation. Accumulating experimental evidence supports a causal role of miRNAs in hematology tumorigenesis. However, the specific functions of miRNAs in the pathogenesis of multiple myeloma (MM) remain to be established. In this study, we demonstrated that miR-186 is commonly downregulated in MM cell lines and patient MM cells. Ectopic expression of miR-186 significantly inhibited cell growth, both in vitro and in vivo, and induced cell cycle G{sub 0}/G{sub 1} arrest. Furthermore, miR-186 induced downregulation of Jagged1 protein expression by directly targeting its 3′-untranslated regionmore » (3′-UTR). Conversely, overexpression of Jagged1 rescued cells from miR-186-induced growth inhibition. Our collective results clearly indicate that miR-186 functions as a tumor suppressor in MM, supporting its potential as a therapeutic target for the disease. - Highlights: • miR-186 expression is decreased in MM. • miR-186 inhibits MM cell proliferation in vitro and in vivo. • Jagged1 is regulated by miR-186. • Overexpression of Jagged1 reverses the effects of miR-186.« less

Metal–Organic Nanosheets Formed via Defect-Mediated Transformation of a Hafnium Metal–Organic Framework

PubMed Central

2017-01-01

We report a hafnium-containing MOF, hcp UiO-67(Hf), which is a ligand-deficient layered analogue of the face-centered cubic fcu UiO-67(Hf). hcp UiO-67 accommodates its lower ligand:metal ratio compared to fcu UiO-67 through a new structural mechanism: the formation of a condensed “double cluster” (Hf12O8(OH)14), analogous to the condensation of coordination polyhedra in oxide frameworks. In oxide frameworks, variable stoichiometry can lead to more complex defect structures, e.g., crystallographic shear planes or modules with differing compositions, which can be the source of further chemical reactivity; likewise, the layered hcp UiO-67 can react further to reversibly form a two-dimensional metal–organic framework, hxl UiO-67. Both three-dimensional hcp UiO-67 and two-dimensional hxl UiO-67 can be delaminated to form metal–organic nanosheets. Delamination of hcp UiO-67 occurs through the cleavage of strong hafnium-carboxylate bonds and is effected under mild conditions, suggesting that defect-ordered MOFs could be a productive route to porous two-dimensional materials. PMID:28343394

Metal-Organic Nanosheets Formed via Defect-Mediated Transformation of a Hafnium Metal-Organic Framework.

PubMed

Cliffe, Matthew J; Castillo-Martínez, Elizabeth; Wu, Yue; Lee, Jeongjae; Forse, Alexander C; Firth, Francesca C N; Moghadam, Peyman Z; Fairen-Jimenez, David; Gaultois, Michael W; Hill, Joshua A; Magdysyuk, Oxana V; Slater, Ben; Goodwin, Andrew L; Grey, Clare P

2017-04-19

We report a hafnium-containing MOF, hcp UiO-67(Hf), which is a ligand-deficient layered analogue of the face-centered cubic fcu UiO-67(Hf). hcp UiO-67 accommodates its lower ligand:metal ratio compared to fcu UiO-67 through a new structural mechanism: the formation of a condensed "double cluster" (Hf 12 O 8 (OH) 14 ), analogous to the condensation of coordination polyhedra in oxide frameworks. In oxide frameworks, variable stoichiometry can lead to more complex defect structures, e.g., crystallographic shear planes or modules with differing compositions, which can be the source of further chemical reactivity; likewise, the layered hcp UiO-67 can react further to reversibly form a two-dimensional metal-organic framework, hxl UiO-67. Both three-dimensional hcp UiO-67 and two-dimensional hxl UiO-67 can be delaminated to form metal-organic nanosheets. Delamination of hcp UiO-67 occurs through the cleavage of strong hafnium-carboxylate bonds and is effected under mild conditions, suggesting that defect-ordered MOFs could be a productive route to porous two-dimensional materials.

Interventional Therapy of Head and Neck Cancer with Lipid Nanoparticle-Carried Rhenium-186 Radionuclide

PubMed Central

French, J. Tyler; Goins, Beth; Saenz, Marcela; Li, Shihong; Garcia-Rojas, Xavier; Phillips, William T.; Otto, Randal A.; Bao, Ande

2010-01-01

Purpose Minimally invasive interventional cancer therapy of drug-carrying lipid nanoparticles (liposomes) via convection enhanced delivery generally applied by the use of an infusion pump can increase intratumoral drug concentration and retention while facilitating broad distribution throughout solid tumors. We investigated the utility of liposome-carrying β-emitting radionuclides to treat head and neck cancer in nude rats by direct intratumoral infusion. Methods Four groups of nude rats were subcutaneously inoculated with human tongue cancer cells. After tumors reached an average size of 1.6 cm3, the treatment group received an intratumoral infusion of liposomal rhenium-186 (186Re) (185 MBq (5 mCi)/cm3 tumor). Three control groups were intratumorally infused with either, 1) unlabeled liposomes, 2) unencapsulated 186Re-perrhenate, or 3) unencapsulated intermediate 186Re-compound (186Re-BMEDA). In vivo distribution of 186Re-activity was measured by planar gamma camera imaging. Tumor therapy and toxicity were assessed by measurements of tumor size, body weight, and hematology. Results Average tumor volume of the 186Re-liposome group on post-treatment day-14 decreased to 87.7±20.1%, while tumor volumes increased to 395.0% - 514.4% on average in other three groups (P<0.001 vs 186Re-liposome group). 186Re-liposomes provided much higher intratumoral retention of 186Re-activity, resulting in an average tumor radiation absorbed dose of 526.3±93.3 Gy, whereas 186Re-perrhenate and 186Re-BMEDA groups had only 3.3±1.2 and 13.4±9.2 Gy tumor doses respectively. No systemic toxicity was observed. Conclusion Liposomal 186Re effectively treated the head and neck cancer with minimal side effects after convection enhanced interventional delivery. These results suggest the potential of liposomal 186Re for clinical application in interventional therapy of cancer. PMID:20478719

16 CFR 18.6 - Plants collected from the wild state.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 16 Commercial Practices 1 2014-01-01 2014-01-01 false Plants collected from the wild state. 18.6... NURSERY INDUSTRY § 18.6 Plants collected from the wild state. It is an unfair or deceptive act or practice to sell, offer for sale, or distribute industry products collected from the wild state without...

16 CFR 18.6 - Plants collected from the wild state.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 16 Commercial Practices 1 2011-01-01 2011-01-01 false Plants collected from the wild state. 18.6... NURSERY INDUSTRY § 18.6 Plants collected from the wild state. It is an unfair or deceptive act or practice to sell, offer for sale, or distribute industry products collected from the wild state without...

16 CFR 18.6 - Plants collected from the wild state.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 16 Commercial Practices 1 2012-01-01 2012-01-01 false Plants collected from the wild state. 18.6... NURSERY INDUSTRY § 18.6 Plants collected from the wild state. It is an unfair or deceptive act or practice to sell, offer for sale, or distribute industry products collected from the wild state without...

16 CFR 18.6 - Plants collected from the wild state.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 16 Commercial Practices 1 2013-01-01 2013-01-01 false Plants collected from the wild state. 18.6... NURSERY INDUSTRY § 18.6 Plants collected from the wild state. It is an unfair or deceptive act or practice to sell, offer for sale, or distribute industry products collected from the wild state without...

40 CFR 61.186 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Inorganic Arsenic Emissions From Arsenic Trioxide and Metallic Arsenic Production Facilities § 61.186 Reporting requirements... at least 30 days prior notice of each reference opacity level determination required in § 61.183(a...

40 CFR 61.186 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) NATIONAL EMISSION STANDARDS FOR HAZARDOUS AIR POLLUTANTS National Emission Standard for Inorganic Arsenic Emissions From Arsenic Trioxide and Metallic Arsenic Production Facilities § 61.186 Reporting requirements... at least 30 days prior notice of each reference opacity level determination required in § 61.183(a...

Applications of the 190Pt-186Os isotope system to geochemistry and cosmochemistry

USGS Publications Warehouse

Walker, R.J.; Morgan, J.W.; Beary, E.S.; Smoliar, M.I.; Czamanske, G.K.; Horan, M.F.

1997-01-01

Platinum is fractionated from osmium primarily as a consequence of processes involving sulfide and metal crystallization. Consequently, the 190Pt-186Os isotope system (190Pt ??? 186Os + ??) shows promise for dating some types of magmatic sulfide ores and evolved iron meteorites. The first 190Pt-186Os isochrons are presented here for ores from the ca. 251 Ma Noril'sk, Siberia plume, and for group IIAB magmatic iron meteorites. Given the known age of the Noril'sk system, a decay constant for 190Pt is determined to be 1.542 ?? 10-12a-1, with ??1% uncertainty. The isochron generated for the IIAB irons is consistent with this decay constant and the known age of the group. The 186Os/188Os ratios of presumably young, mantle-derived osmiridiums and also the carbonaceous chondrite Allende were measured to high-precision to constrain the composition of the modern upper mantle. These compositions overlap, indicating that the upper mantle is chondritic within the level of resolution now available. Our best estimate for this 186Os/188Os ratio is 0.119834 ?? 2 (2??M). The 190Pt/186Os ratios determined for six enstatite chondrites average 0.001659 ?? 75, which is very similar to published values for carbonaceous chondrites. Using this ratio and the presumed composition of the modern upper mantle and chondrites, a solar system initial 186Os/188Os ratio of 0.119820 is calculated. In comparison to the modern upper mantle composition, the 186Os/188Os ratio of the Noril'sk plume was approximately 0.012% enriched in 186Os. Possible reasons for this heterogeneity include the recycling of Pt-rich crust into the mantle source of the plume and derivation of the osmium from the outer core. Derivation of the osmium from the outer core is our favored model. Copyright ?? 1997 Elsevier Science Ltd.

47 CFR 0.186 - Emergency Relocation Board.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMISSION ORGANIZATION Organization Homeland Security, Defense and Emergency Preparedness Functions § 0.186 Emergency Relocation Board. (a) As specified in the...] Public Safety and Homeland Security Bureau ...

47 CFR 0.186 - Emergency Relocation Board.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMISSION ORGANIZATION Organization Homeland Security, Defense and Emergency Preparedness Functions § 0.186 Emergency Relocation Board. (a) As specified in the...] Public Safety and Homeland Security Bureau ...

47 CFR 0.186 - Emergency Relocation Board.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMISSION ORGANIZATION Organization Homeland Security, Defense and Emergency Preparedness Functions § 0.186 Emergency Relocation Board. (a) As specified in the...] Public Safety and Homeland Security Bureau ...

47 CFR 0.186 - Emergency Relocation Board.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMISSION ORGANIZATION Organization Homeland Security, Defense and Emergency Preparedness Functions § 0.186 Emergency Relocation Board. (a) As specified in the...] Public Safety and Homeland Security Bureau ...

47 CFR 0.186 - Emergency Relocation Board.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Telecommunication FEDERAL COMMUNICATIONS COMMISSION GENERAL COMMISSION ORGANIZATION Organization Homeland Security, Defense and Emergency Preparedness Functions § 0.186 Emergency Relocation Board. (a) As specified in the...] Public Safety and Homeland Security Bureau ...

38 CFR 18.6 - Compliance information.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 38 Pensions, Bonuses, and Veterans' Relief 2 2010-07-01 2010-07-01 false Compliance information... THE CIVIL RIGHTS ACT OF 1964 General § 18.6 Compliance information. (a) Cooperation and assistance... compliance reports at such times, and in such form and containing such information, as the responsible agency...

27 CFR 40.186 - Record in support of transfers in bond.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 2 2010-04-01 2010-04-01 false Record in support of transfers in bond. 40.186 Section 40.186 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY (CONTINUED) TOBACCO MANUFACTURE OF TOBACCO PRODUCTS, CIGARETTE...

Pox 186: A Nearby Protogalaxy?

NASA Astrophysics Data System (ADS)

Corbin, Michael

1999-07-01

Blue Compact Dwarf Galaxies {BCDGs} typically consist of clusters of early-type stars embedded in older, evolved stellar populations similar in size and shape to normal dwarf ellipticals. However, deep ground-based CCD images of one faint BCDG, Pox 186, reveal a very compact { 5" diameter} structure with no evidence of an underlying older population. Optical spectroscopy of this object also indicates that a large number of Wolf-Rayet stars are present, which implies that a burst of star formation must have occurred very recently {<=sssim 10^7 years ago}. It has thus been suggested that Pox 186 is a protogalaxy, forming its very first generation of stars. Further investigation of this possibility requires the high angular resolution and ultraviolet spectral coverage that only HST can provide. Using WFPC2, we propose to image the galaxy in the U, V, and I bands, in order to better test for the presence of an underlying evolved population and to reveal any substructure in its star-forming regions. Using STIS, we will obtain low-resolution ultraviolet spectra of the galaxy for combination with ground-based spectra covering the optical through near infrared. This will allow us to determine its spectral energy distribution, metallicity, and dust content, which will in turn constrain its age and star formation history.

POX 186: A Dwarf Galaxy Under Construction?

NASA Astrophysics Data System (ADS)

Corbin, M. R.; Vacca, W. D.

2000-12-01

We have obtained deep images of the ultracompact ( ~ 3'') blue compact dwarf galaxy POX 186 in the F336W, F555W, and F814W filters of the Planetary Camera of the Hubble Space Telescope. We have additionally obtained a low-resolution near ultraviolet spectrum of the object with STIS and combine this with a ground-based spectrum covering the visible continuum and emission lines. Our images confirm this object to be highly compact, with a maximum projected size of only ~ 240 pc, making it one of the smallest galaxies known. We also confirm that the outer regions of the galaxy consist of an evolved stellar population, ruling out earlier speculations that POX 186 is a protogalaxy. However, the PC images reveal the galaxy to have a highly irregular morphology, with a pronounced tidal arm on its western side. This morphology is strongly suggestive of a recent collision between two smaller components which has in turn triggered the central starburst. The F336W image also shows that the material in this tidal stream is actively star forming. Given the very small ( ~ 100 pc) sizes of the colliding components, POX 186 may be a dwarf galaxy in the early stages of formation, which would be consistent with current ``downsizing'' models of galaxy formation in which the least massive objects are the last to form. This work is supported by NASA and the Space Telescope Science Institute.

Design study: A 186 kW lightweight diesel aircraft engine

NASA Technical Reports Server (NTRS)

Brouwers, A. P.

1980-01-01

The design of an aircraft engine capable of developing 186 kW shaft power at a 7620 m altitude is described. The 186 kW design takes into account expected new developments in aircraft designs resulting in a reassessment of the power requirements at the cruise mode operation. Based on the results of this analysis a three phase technology development program is projected resulting in production dates of 1985, 1992, and 2000.

187Os-186Os and He Isotope Systematics of Iceland Picrites

NASA Astrophysics Data System (ADS)

Brandon, A. D.; Brandon, A. D.; Graham, D.; Gautason, B.

2001-12-01

Iceland is one of the longest-lived modern plumes, and seismic imaging supports a model where the roots of this plume are at the base of the lower mantle. Hence, Os isotopic data for lavas from this plume are ideal for further testing the role of core-mantle chemical exchange at the site of plume generation in the lower mantle, and for addressing the origin of Os-He isotopic variation in plumes. Recent work has shown that lavas from some plume systems (Hawaii, Noril'sk-Siberia, Gorgona) show coupled enrichments in 186Os/188Os and 187Os/188Os, not observed in upper mantle materials including abyssal peridotites. Picrites from Hawaii display a positive correlation between 186Os/188Os and He isotopes (R/Ra), where range in 186Os/188Os of 0.119834+/-28 to 0.1198475+/-29 and corresponding R/Ra from +7 to +25. These systematics are consistent with a lower mantle source for the radiogenic 186Os signal in the Hawaiian plume. The coupled Os enrichments in these plumes has been attributed to core-mantle chemical exchange, consistent with generation of the Hawaiian plume at the base of the lower mantle in D". Other potentially viable models await additional scrutiny. New He isotope and high precision 186Os/188Os and 187Os/188Os measurements for Iceland picrites show unique systematics compared to Hawaii. These picrites have 187Os/188Os ranging from 0.1297 to 0.1381 and R/Ra of +9 to +18, with generally higher R/Ra correlating with higher 187Os/188Os. Unlike the Hawaiian picrites from Hualalai and Loihi, which have coupled enrichments in 186Os/188Os and 187Os/188Os, the Iceland picrites show no enrichment 186Os/188Os - 0.1198363+/-28 (2s, n=14). Such Os-He isotopic variations require one end-member source that has high R/Ra, coupled with a long term elevated Re/Os and Pt/Os similar to that of the upper mantle. These systematics are inconsistent with either known upper mantle materials or those purported for ancient recycled slabs and may be a previously unidentified component

Hafnium, Tungsten, and the Differentiation of the Moon and Mars

NASA Astrophysics Data System (ADS)

Taylor, G. J.

2003-11-01

Measurements of the isotopic composition of tungsten (W) show that lunar samples and Martian meteorites have an excess of W-182. This was produced by the decay of hafnium-182 (Hf-182), an isotope with a half-life of only 9 million years. Because tungsten dissolves enthusiastically in metallic iron and hafnium does not, it is possible to use the abundance of W-182 in rocks formed by melting of the silicate mantle as an indicator of the timing of core formation. However, the concentrations of Hf and W in rocky material can be affected by melting and crystallization, so we also need to know how each element concentrates in common minerals in the mantles of the Moon and Mars. The behavior of Hf has been studied experimentally, but this is not true of W. Kevin Righter (Johnson Space Center) and Charles (Chip) Shearer (University of New Mexico) have filled this knowledge void by determining how W partitions between olivine, high- and low-calcium pyroxene, plagioclase feldspar, and garnet. The new data allowed Righter and Shearer to reexamine available measurements of the isotopic composition of W in lunar samples and Martian meteorites. Their analysis suggests that the lunar magma ocean, a huge magma system that surrounded the Moon when it formed, solidified in less than 30 million years. This is shorter than many theoretical calculations suggest. Pathfinder data and chemical data from Martian meteorites suggest that the core of Mars makes up about 20% of the planet. Core formation and subsequent melting of a region of the mantle containing garnet and high-calcium pyroxene took place less than 20-30 million years after the formation of the first solids in the solar system. This type of research shows the importance of measurements of isotopic compositions of radioactive elements or their decay products and laboratory experiments on the geochemical behavior of those elements.

Study of bulk Hafnium oxide (HfO2) under compression

NASA Astrophysics Data System (ADS)

Pathak, Santanu; Mandal, Guruprasad; Das, Parnika

2018-04-01

Hafnium oxide (HfO2) is a technologically important material. This material has K-value of 25 and band gap 5.8 eV. A k value of 25-30 is preferred for a gate dielectric [1]. As it shows good insulating and capacitive properties, HfO2 is being considered as a replacement to SiO2 in microelectronic devices as gate dielectrics. On the other hand because of toughening mechanism due to phase transformation induced by stress field observed in these oxides, HFO2 has been a material of investigations in various configurations for a very long time. However the controversies about phase transition of HfO2 under pressure still exists. High quality synchrotron radiation has been used to study the structural phase transition of HfO2 under pressure.

Publications - GMC 186 | Alaska Division of Geological & Geophysical

Science.gov Websites

DGGS GMC 186 Publication Details Title: Petrographic thin-section photographs of cuttings (14220'-14250 for more information. Bibliographic Reference Unknown, 1991, Petrographic thin-section photographs of

Multimode resistive switching in nanoscale hafnium oxide stack as studied by atomic force microscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hou, Y., E-mail: houyi@pku.edu.cn, E-mail: lfliu@pku.edu.cn; IMEC, Kapeldreef 75, B-3001 Heverlee; Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, B-3001 Heverlee

2016-07-11

The nanoscale resistive switching in hafnium oxide stack is investigated by the conductive atomic force microscopy (C-AFM). The initial oxide stack is insulating and electrical stress from the C-AFM tip induces nanometric conductive filaments. Multimode resistive switching can be observed in consecutive operation cycles at one spot. The different modes are interpreted in the framework of a low defect quantum point contact theory. The model implies that the optimization of the conductive filament active region is crucial for the future application of nanoscale resistive switching devices.

50 CFR 216.186 - Requirements for reporting.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Low Frequency Active (SURTASS LFA sonar) Sonar § 216.186 Requirements for reporting. (a) The Holder of... of each vessel during each mission; (2) Information on sonar transmissions during each mission; (3... must contain an unclassified analysis of new passive sonar technologies and an assessment of whether...

50 CFR 216.186 - Requirements for reporting.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Low Frequency Active (SURTASS LFA sonar) Sonar § 216.186 Requirements for reporting. (a) The Holder of... of each vessel during each mission; (2) Information on sonar transmissions during each mission; (3... must contain an unclassified analysis of new passive sonar technologies and an assessment of whether...

Composition effects on mechanical properties of tungsten-rhenium-hafnium-carbon alloys

NASA Technical Reports Server (NTRS)

Witzke, W. R.

1973-01-01

The mechanical properties of rod and sheet fabricated from arc melted W-4Re-Hf-C alloys containing up to about 0.8 mol percent hafnium carbide (HfC) were evaluated in the as-worked condition. The DBTT's of electropolished bend and tensile specimens were independent of HfC content in this range but dependent on excess Hf or C above that required for stoichiometric HfC. Low temperature ductility was a maximum at Hf contents slightly in excess of stoichiometric. Variations in high temperature strength were also dependent on excess Hf and C. Maximum creep strengthening also occurred at Hf contents in excess of stoichiometric. Analysis of extracted second phase particles indicated that creep strength was reduced by increasing WC content in the HfC particles.

27 CFR 555.186 - Seizure or forfeiture.

Code of Federal Regulations, 2013 CFR

2013-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.186 Seizure or forfeiture. Any plastic explosive that does not contain a detection agent in violation of 18 U... of this chapter for regulations on summary destruction of plastic explosives that do not contain a...

27 CFR 555.186 - Seizure or forfeiture.

Code of Federal Regulations, 2014 CFR

2014-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.186 Seizure or forfeiture. Any plastic explosive that does not contain a detection agent in violation of 18 U... of this chapter for regulations on summary destruction of plastic explosives that do not contain a...

27 CFR 555.186 - Seizure or forfeiture.

Code of Federal Regulations, 2012 CFR

2012-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.186 Seizure or forfeiture. Any plastic explosive that does not contain a detection agent in violation of 18 U... of this chapter for regulations on summary destruction of plastic explosives that do not contain a...

27 CFR 555.186 - Seizure or forfeiture.

Code of Federal Regulations, 2011 CFR

2011-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.186 Seizure or forfeiture. Any plastic explosive that does not contain a detection agent in violation of 18 U... of this chapter for regulations on summary destruction of plastic explosives that do not contain a...

27 CFR 555.186 - Seizure or forfeiture.

Code of Federal Regulations, 2010 CFR

2010-04-01

... EXPLOSIVES, DEPARTMENT OF JUSTICE EXPLOSIVES COMMERCE IN EXPLOSIVES Marking of Plastic Explosives § 555.186 Seizure or forfeiture. Any plastic explosive that does not contain a detection agent in violation of 18 U... of this chapter for regulations on summary destruction of plastic explosives that do not contain a...

76 FR 63987 - Fifty-Fifth Meeting: RTCA Special Committee 186: Automatic Dependent Surveillance-Broadcast (ADS-B)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-14

... Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B) AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of RTCA Special Committee 186: Automatic Dependent Surveillance Broadcast... Special Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B). DATES: The meeting will be...

76 FR 3932 - Fifty-Third Meeting: RTCA Special Committee 186: Automatic Dependent Surveillance-Broadcast (ADS-B)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-01-21

... Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B) AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of RTCA Special Committee 186: Automatic Dependent Surveillance--Broadcast... Special Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B). DATES: The meeting will be...

76 FR 22160 - Fifty-Fourth Meeting: RTCA Special Committee 186: Automatic Dependent Surveillance-Broadcast (ADS-B)

Federal Register 2010, 2011, 2012, 2013, 2014

2011-04-20

... Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B) AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of RTCA Special Committee 186: Automatic Dependent Surveillance--Broadcast... Special Committee 186: Automatic Dependent Surveillance--Broadcast (ADS-B). DATES: The meeting will be...

29 CFR 18.6 - Motions and requests.

Code of Federal Regulations, 2014 CFR

2014-07-01

... ADMINISTRATIVE LAW JUDGES General § 18.6 Motions and requests. (a) Generally. Any application for an order or any... a motion is served, or within such other period as the administrative law judge may fix, any party...) Oral arguments or briefs. No oral argument will be heard on motions unless the administrative law judge...

Pyroelectricity of silicon-doped hafnium oxide thin films

NASA Astrophysics Data System (ADS)

Jachalke, Sven; Schenk, Tony; Park, Min Hyuk; Schroeder, Uwe; Mikolajick, Thomas; Stöcker, Hartmut; Mehner, Erik; Meyer, Dirk C.

2018-04-01

Ferroelectricity in hafnium oxide thin films is known to be induced by various doping elements and in solid-solution with zirconia. While a wealth of studies is focused on their basic ferroelectric properties and memory applications, thorough studies of the related pyroelectric properties and their application potential are only rarely found. This work investigates the impact of Si doping on the phase composition and ferro- as well as pyroelectric properties of thin film capacitors. Dynamic hysteresis measurements and the field-free Sharp-Garn method were used to correlate the reported orthorhombic phase fractions with the remanent polarization and pyroelectric coefficient. Maximum values of 8.21 µC cm-2 and -46.2 µC K-1 m-2 for remanent polarization and pyroelectric coefficient were found for a Si content of 2.0 at%, respectively. Moreover, temperature-dependent measurements reveal nearly constant values for the pyroelectric coefficient and remanent polarization over the temperature range of 0 ° C to 170 ° C , which make the material a promising candidate for IR sensor and energy conversion applications beyond the commonly discussed use in memory applications.

Zirconium and hafnium fractionation in differentiation of alkali carbonatite magmatic systems

NASA Astrophysics Data System (ADS)

Kogarko, L. N.

2016-05-01

Zirconium and hafnium are valuable strategic metals which are in high demand in industry. The Zr and Hf contents are elevated in the final products of magmatic differentiation of alkali carbonatite rocks in the Polar Siberia region (Guli Complex) and Ukraine (Chernigov Massif). Early pyroxene fractionation led to an increase in the Zr/Hf ratio in the evolution of the ultramafic-alkali magmatic system due to a higher distribution coefficient of Hf in pyroxene with respect to Zr. The Rayleigh equation was used to calculate a quantitative model of variation in the Zr/Hf ratio in the development of the Guli magmatic system. Alkali carbonatite rocks originated from rare element-rich mantle reservoirs, in particular, the metasomatized mantle. Carbonated mantle xenoliths are characterized by a high Zr/Hf ratio due to clinopyroxene development during metasomatic replacement of orthopyroxene by carbonate fluid melt.

Analysis of the Nuclear Structure of 186 Re Using Neutron-Induced Reactions

NASA Astrophysics Data System (ADS)

Matters, David; McClory, John; Carroll, James; Chiara, Chris; Fotiades, Nikolaos; Devlin, Matt; Nelson, Ron O.

2015-04-01

Evaluated nuclear structure data for 186 Re identifies the majority of spin-parity assignments as tentative, with approximate values associated with the energies of several levels and transitions. In particular, the absence of known transitions that feed the Jπ =8+ isomer motivates their discovery, which would have astrophysical implications and a potential application in the development of an isomer power source. Using the GErmanium Array for Neutron Induced Excitations (GEANIE) spectrometer at the Los Alamos Neutron Science Center (LANSCE) Weapons Neutron Research (WNR) facility, the (n,2n γ) and (n,n' γ) reactions in a 99.52% enriched 187 Re target were used to measure γ-ray excitation functions in 186 Re and 187 Re, respectively. A preliminary analysis of the data obtained from the experiment reveals several new transitions in 186 Re and 187 Re.

Experimental and first-principles studies on the elastic properties of α-hafnium metal under pressure

DOE PAGES

Qi, Xintong; Wang, Xuebing; Chen, Ting; ...

2016-03-30

Compressional and shear wave velocities of the α phase of hafnium have been measured up to 10.4 GPa at room temperature using ultrasonic interferometry in a multi-anvil apparatus. A finite strain equation of state analysis yielded K s0 = 110.4 (5) GPa, G 0 = 54.7(5) GPa,K s0' = 3.7 and G 0' = 0.6 for the elastic bulk and shear moduli and their pressure derivatives at ambient conditions. Complementary to the experimental data, the single crystal elastic constants, elastic anisotropy and the unit cell axial ratio c/a of α-hafnium at high pressures were investigated by Density Functional Theory (DFT)more » based first principles calculations. A c/a value of 1.605 is predicted for α-Hf at 40 GPa, which is in excellent agreement with previous experimental results. The low-pressure derivative of the shear modulus observed in our experimental data up to 10 GPa was found to originate from the elastic constant C44 which exhibits negligible pressure dependence within the current experimental pressure range. At higher pressures (>10 GPa), C 44 was predicted to soften and the shear wave velocity ν S trended to decrease with pressure, which can be interpreted as a precursor to the α-ω transition similar to that observed in other group IV elements (titanium and zirconium). Here, the acoustic velocities, bulk and shear moduli, and the acoustic Debye temperature (θ D = 240.1 K) determined from the current experiments were all compared well with those predicted by our theoretical DFT calculations.« less

Stress-rupture strength and microstructural stability of tungsten-hafnium-carbon-wire reinforced superalloy composites

NASA Technical Reports Server (NTRS)

Petrasek, D. W.; Signorelli, R. A.

1974-01-01

Tungsten-hafnium-carbon - superalloy composites were found to be potentially useful for turbine blade applications on the basis of stress-rupture strength. The 100- and 1000-hr rupture strengths calculated for 70 vol. % fiber composites based on test data at 1090C (2000F) were 420 and 280 MN/m2 (61,000 and 41,000 psi, respectively). The investigation indicated that, with better quality fibers, composites having 100- and 1000-hr rupture strengths of 570 and 370 MN/m2 (82,000 and 54,000 psi, respectively), may be obtained. Metallographic studies indicated sufficient fiber-matrix compatibility for 1000 hr or more at 1090C (2000F).

Precise Determination of the Intensity of 226Ra Alpha Decay to the 186 keV Excited State

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.P. LaMont; R.J. Gehrke; S.E. Glover

There is a significant discrepancy in the reported values for the emission probability of the 186 keV gamma-ray resulting from the alpha decay of 226 Ra to 186 keV excited state of 222 Rn. Published values fall in the range of 3.28 to 3.59 gamma-rays per 100 alpha-decays. An interesting observation is that the lower value, 3.28, is based on measuring the 186 keV gamma-ray intensity relative to the 226 Ra alpha-branch to the 186 keV level. The higher values, which are close to 3.59, are based on measuring the gamma-ray intensity from mass standards of 226 Ra that aremore » traceable to the mass standards prepared by HÓNIGSCHMID in the early 1930''s. This discrepancy was resolved in this work by carefully measuring the 226 Ra alpha-branch intensities, then applying the theoretical E2 multipolarity internal conversion coefficient of 0.692±0.007 to calculate the 186 keV gamma-ray emission probability. The measured value for the alpha branch to the 186 keV excited state was (6.16±0.03)%, which gives a 186 keV gamma-ray emission probability of (3.64±0.04)%. This value is in excellent agreement with the most recently reported 186 keV gamma-ray emission probabilities determined using 226 Ra mass standards.« less

34 CFR 403.186 - What are the administrative cost requirements applicable to a State?

Code of Federal Regulations, 2012 CFR

2012-07-01

... 34 Education 3 2012-07-01 2012-07-01 false What are the administrative cost requirements applicable to a State? 403.186 Section 403.186 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF EDUCATION STATE VOCATIONAL AND...

34 CFR 403.186 - What are the administrative cost requirements applicable to a State?

Code of Federal Regulations, 2011 CFR

2011-07-01

... 34 Education 3 2011-07-01 2011-07-01 false What are the administrative cost requirements applicable to a State? 403.186 Section 403.186 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF EDUCATION STATE VOCATIONAL AND...

34 CFR 403.186 - What are the administrative cost requirements applicable to a State?

Code of Federal Regulations, 2014 CFR

2014-07-01

... 34 Education 3 2014-07-01 2014-07-01 false What are the administrative cost requirements applicable to a State? 403.186 Section 403.186 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF EDUCATION STATE VOCATIONAL AND...

34 CFR 403.186 - What are the administrative cost requirements applicable to a State?

Code of Federal Regulations, 2013 CFR

2013-07-01

... 34 Education 3 2013-07-01 2013-07-01 false What are the administrative cost requirements applicable to a State? 403.186 Section 403.186 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF EDUCATION STATE VOCATIONAL AND...

34 CFR 403.186 - What are the administrative cost requirements applicable to a State?

Code of Federal Regulations, 2010 CFR

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false What are the administrative cost requirements applicable to a State? 403.186 Section 403.186 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF VOCATIONAL AND ADULT EDUCATION, DEPARTMENT OF EDUCATION STATE VOCATIONAL AND...

Silicon doped hafnium oxide (HSO) and hafnium zirconium oxide (HZO) based FeFET: A material relation to device physics

NASA Astrophysics Data System (ADS)

Ali, T.; Polakowski, P.; Riedel, S.; Büttner, T.; Kämpfe, T.; Rudolph, M.; Pätzold, B.; Seidel, K.; Löhr, D.; Hoffmann, R.; Czernohorsky, M.; Kühnel, K.; Thrun, X.; Hanisch, N.; Steinke, P.; Calvo, J.; Müller, J.

2018-05-01

The recent discovery of ferroelectricity in thin film HfO2 materials renewed the interest in ferroelectric FET (FeFET) as an emerging nonvolatile memory providing a potential high speed and low power Flash alternative. Here, we report more insight into FeFET performance by integrating two types of ferroelectric (FE) materials and varying their properties. By varying the material type [HfO2 (HSO) versus hafnium zirconium oxide (HZO)], optimum content (Si doping/mixture ratio), and film thickness, a material relation to FeFET device physics is concluded. As for the material type, an improved FeFET performance is observed for HZO integration with memory window (MW) comparable to theoretical values. For different Si contents, the HSO based FeFET exhibited a MW trend with different stabilized phases. Similarly, the HZO FeFET shows MW dependence on the Hf:Zr mixture ratio. A maximized MW is obtained with cycle ratios of 16:1 (HfO2:Si) and 1:1 (Hf:Zr) as measured on HSO and HZO based FeFETs, respectively. The thickness variation shows a trend of increasing MW with the increased FE layer thickness confirming early theoretical predictions. The FeFET material aspects and stack physics are discussed with insight into the interplay factors, while optimum FE material parameters are outlined in relation to performance.

27 CFR 25.186 - Record of beer transferred.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Record of beer transferred..., DEPARTMENT OF THE TREASURY LIQUORS BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.186 Record of beer transferred. (a) Preparation of invoice. When beer is transferred between...

27 CFR 25.186 - Record of beer transferred.

Code of Federal Regulations, 2013 CFR

2013-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Record of beer transferred..., DEPARTMENT OF THE TREASURY ALCOHOL BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.186 Record of beer transferred. (a) Preparation of invoice. When beer is transferred between...

27 CFR 25.186 - Record of beer transferred.

Code of Federal Regulations, 2012 CFR

2012-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Record of beer transferred..., DEPARTMENT OF THE TREASURY LIQUORS BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.186 Record of beer transferred. (a) Preparation of invoice. When beer is transferred between...

27 CFR 25.186 - Record of beer transferred.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Record of beer transferred..., DEPARTMENT OF THE TREASURY ALCOHOL BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.186 Record of beer transferred. (a) Preparation of invoice. When beer is transferred between...

27 CFR 25.186 - Record of beer transferred.

Code of Federal Regulations, 2011 CFR

2011-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Record of beer transferred..., DEPARTMENT OF THE TREASURY LIQUORS BEER Removals Without Payment of Tax Transfer to Another Brewery of Same Ownership § 25.186 Record of beer transferred. (a) Preparation of invoice. When beer is transferred between...

Atomic layer deposition of hafnium oxide: A detailed reaction mechanism from first principles

NASA Astrophysics Data System (ADS)

Widjaja, Yuniarto; Musgrave, Charles B.

2002-08-01

Atomic layer deposition (ALD) of hafnium oxide (HfO2) using HfCl4 and H2O as precursors is studied using density functional theory. The mechanism consists of two deposition half-reactions: (1) HfCl4 with Hf-OH sites, and (2) H2O with Hf-Cl sites. Both half-reactions exhibit stable intermediates with energies lower than those of the final products. We show that increasing the temperature reduces the stability of the complex. However, increasing temperature also increases the dissociation free-energy barrier, which in turn results in increased desorption of adsorbed precursors. Both half-reactions are qualitatively similar to the corresponding reactions of ZrO2 ALD using ZrCl4 and H2O.

Intrinsic Defect Ferromagnetism: The case of Hafnium Oxide

NASA Astrophysics Data System (ADS)

Das Pemmaraju, Chaitanya

2005-03-01

In view of the recent experimental reports of intrinsic ferromagnetism in Hafnium Oxide (HfO2) thin film systems ootnotetextM. Venkatesan, C. B. Fitzgerald, J. M. D. Coey Nature 430, 630 (2004) Brief Communications, we carried out first principles investigations to look for magnetic structure in HfO2 possibly brought about by the presence of small concentrations of intrinsic point defects. Ab initio electronic structure calculations using Density Functional Theory (DFT) show that isolated cation vacancy sites in HfO2 lead to the formation of high spin defect states which couple ferromagnetically to each other. Interestingly, these high spin states are observed in the low symmetry monoclinic and tetragonal phases while the highly symmetric cubic flourite phase exhibits a non-magnetic ground state. Detailed studies of the electronic structure of cation vacancies in the three crystalline phases of Hafnia show that symmetry leading to orbitally degenerate defect levels is not a pre-requsite for ferromagnetism and that the interplay between Kinetic, Coulomb and Exchange energy together with favourable coupling to the Crystalline environment can lead to high spin ferromagnetic ground states even in extreme low symmetry systems like monoclinic HfO2. These findings open up a much wider class of systems to the possibility of intrinsic defect ferromagnetism.

Work functions of hafnium nitride thin films as emitter material for field emitter arrays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gotoh, Yasuhito, E-mail: gotoh.yasuhito.5w@kyoto-u.ac.jp; Fujiwara, Sho; Tsuji, Hiroshi

The work functions of hafnium nitride thin films prepared by radio-frequency magnetron sputtering were investigated in vacuum, before and after surface cleaning processes, with a view of improving the properties of as-fabricated field emitter arrays comprising hafnium nitride emitters. The measurement of the work function was first performed for the as-deposited films and then for films subjected to surface cleaning process, either thermal treatment or ion bombardment. Thermal treatment at a maximum temperature of 300 °C reduced the work function by 0.7 eV. Once the film was heated, the work function maintained the reduced value, even after cooling to room temperature. Amore » little change in the work function was observed for the second and third thermal treatments. The ion bombardment was conducted by exposing the sample to a thin plasma for different sample bias conditions and processing times. When the sample was biased at −10 V, the work function decreased by 0.6 eV. The work function reduction became saturated in the early stage of the ion bombardment. When the sample was biased at −50 V, the work function exhibited different behaviors, that is, first it decreased rapidly and then increased in response to the increase in processing time. The lowest attainable work function was found to be 4.00 eV. It should be noted that none of the work function values reported in this paper were obtained using surfaces that were demonstrated to be free from oxygen contamination. The present results suggest that the current–voltage characteristics of a field emitter array can be improved by a factor of 25–50 by the examined postprocesses.« less

The interfacial orientation relationship of oxide nanoparticles in a hafnium-containing oxide dispersion-strengthened austenitic stainless steel

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miao, Yinbin, E-mail: miao2@illinois.edu; Mo, Kun; Cui, Bai

2015-03-15

This work reports comprehensive investigations on the orientation relationship of the oxide nanoparticles in a hafnium-containing austenitic oxide dispersion-strengthened 316 stainless steel. The phases of the oxide nanoparticles were determined by a combination of scanning transmission electron microscopy–electron dispersive X-ray spectroscopy, atom probe tomography and synchrotron X-ray diffraction to be complex Y–Ti–Hf–O compounds with similar crystal structures, including bixbyite Y{sub 2}O{sub 3}, fluorite Y{sub 2}O{sub 3}–HfO{sub 2} solid solution and pyrochlore (or fluorite) Y{sub 2}(Ti,Hf){sub 2−x}O{sub 7−x}. High resolution transmission electron microscopy was used to characterize the particle–matrix interfaces. Two different coherency relationships along with one axis-parallel relation between themore » oxide nanoparticles and the steel matrix were found. The size of the nanoparticles significantly influences the orientation relationship. The results provide insight into the relationship of these nanoparticles with the matrix, which has implications for interpreting material properties as well as responses to radiation. - Highlights: • The oxide nanoparticles in a hafnium-containing austenitic ODS were characterized. • The nanoparticles are Y–Hf–Ti–O enriched phases according to APT and STEM–EDS. • Two coherency and an axis-parallel orientation relationships were found by HR-TEM. • Particle size has a prominent effect on the orientation relationship (OR). • Formation mechanism of the oxide nanoparticles was discussed based on the ORs.« less

Histamine H{sub 3} receptor antagonist OUP-186 attenuates the proliferation of cultured human breast cancer cell lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tanaka, Satoshi; Sakaguchi, Minoru; Yoneyama, Hiroki

Histamine is involved in various physiological functions, including its neurotransmitter actions in the central nervous system and its action as a causative agent of inflammation, allergic reactions, and gastric acid secretions. Histamine expression and biosynthesis have been detected in breast cancer cells. It was recently suggested that the histamine H{sub 3} receptor (H{sub 3}R) plays a role in the proliferation of breast cancer cells. We recently developed the non-imidazole H{sub 3}R antagonist OUP-186 which exhibited a potent and selective human H{sub 3}R antagonistic activity as well as no activity against the human histamine H{sub 4} receptor (H{sub 4}R). In thismore » study, we compared the effects of OUP-186 on the proliferation of estrogen receptor negative (ER−) breast cancer cells (MDA-MB-231) and ER+ breast cancer cells (MCF7) to the effects of clobenpropit (potent imidazole-containing H{sub 3}R antagonist). OUP-186 and clobenpropit suppressed the proliferation of breast cancer cells. The IC{sub 50} values at 48 h for OUP-186 and clobenpropit were approximately 10 μM and 50 μM, respectively. Furthermore, OUP-186 potently induced cell death by activating caspase-3/7, whereas cell death was only slightly induced by clobenpropit. In addition, OUP-186 treatment blocked the proliferation increase triggered by 100 μM (R)-(-)-α-methylhistamine (H{sub 3}R agonist). The use of 4-methylhistamine (H{sub 4}R agonist) and JNJ10191584 (selective H{sub 4}R antagonist) did not affect breast cancer proliferation. These results indicate that OUP-186 potently suppresses proliferation and induces caspase-dependent apoptotic death in both ER+ and ER-breast cancer cells. - Highlights: • OUP-186, a histamine H{sub 3} receptor antagonist, effects breast cancer cell growth. • OUP-186 potently suppressed proliferation and induced caspase-dependent apoptosis. • OUP-186 may be an effective drug against ER+ and ER− breast cancers.« less

77 FR 21538 - Announcing DRAFT Revisions to Federal Information Processing Standard (FIPS) 186-3, Digital...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-10

... Technology (NIST) requests comments on revisions to Federal Information Processing Standard (FIPS) 186-3... http://csrc.nist.gov/publications/PubsDrafts.html . DATES: Comments must be received on or before [email protected]nist.gov , with ``186-3 Change Notice'' in the subject line. FOR FURTHER...

18 CFR 367.1860 - Account 186, Miscellaneous deferred debits.

Code of Federal Regulations, 2010 CFR

2010-04-01

... ENERGY REGULATORY COMMISSION, DEPARTMENT OF ENERGY REGULATIONS UNDER THE PUBLIC UTILITY HOLDING COMPANY... COMPANIES SUBJECT TO THE PROVISIONS OF THE PUBLIC UTILITY HOLDING COMPANY ACT OF 2005, FEDERAL POWER ACT AND NATURAL GAS ACT Balance Sheet Chart of Accounts Deferred Debits § 367.1860 Account 186, Miscellaneous...

40 CFR 421.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Germanium and Gallium Subcategory § 421.186 Pretreatment standards for new sources. Except as provided in 40... sources. The mass of wastewater pollutants in primary and secondary germanium and gallium process... Primary and Secondary Germanium and Gallium Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Germanium and Gallium Subcategory § 421.186 Pretreatment standards for new sources. Except as provided in 40... sources. The mass of wastewater pollutants in primary and secondary germanium and gallium process... Primary and Secondary Germanium and Gallium Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Germanium and Gallium Subcategory § 421.186 Pretreatment standards for new sources. Except as provided in 40... sources. The mass of wastewater pollutants in primary and secondary germanium and gallium process... Primary and Secondary Germanium and Gallium Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Germanium and Gallium Subcategory § 421.186 Pretreatment standards for new sources. Except as provided in 40... sources. The mass of wastewater pollutants in primary and secondary germanium and gallium process... Primary and Secondary Germanium and Gallium Subcategory Pollutant or pollutant property Maximum for any 1...

40 CFR 421.186 - Pretreatment standards for new sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Germanium and Gallium Subcategory § 421.186 Pretreatment standards for new sources. Except as provided in 40... sources. The mass of wastewater pollutants in primary and secondary germanium and gallium process... Primary and Secondary Germanium and Gallium Subcategory Pollutant or pollutant property Maximum for any 1...

Tailoring the index of refraction of nanocrystalline hafnium oxide thin films

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vargas, Mirella; Murphy, N. R.; Ramana, C. V., E-mail: rvchintalapalle@utep.edu

2014-03-10

Hafnium oxide (HfO{sub 2}) films were grown by sputter-deposition by varying the growth temperature (T{sub s} = 25–700 °C). HfO{sub 2} films grown at T{sub s} < 200 °C were amorphous, while those grown at T{sub s} ≥ 200 °C were monoclinic, nanocrystalline with (1{sup ¯}11) texturing. X-ray reflectivity (XRR) analyses indicate that the film-density (ρ) increases with increasing T{sub s}. The index of refraction (n) profiles derived from spectroscopic ellipsometry analyses follow the Cauchy dispersion relation. Lorentz-Lorenz analysis (n{sub (λ)} = 550 nm) and optical-model adopted agree well with the XRR data/analyses. A direct T{sub s}-ρ-n relationship suggests that tailoring the optical quality is possible by tuning T{sub s} and themore » microstructure of HfO{sub 2} films.« less

Structure of the Kπ = 4+ bands in 186,188Os

NASA Astrophysics Data System (ADS)

Phillips, A. A.; Garrett, P. E.; Bettermann, L.; Braun, N.; Burke, D. G.; Demand, G. A.; Faestermann, T.; Finlay, P.; Green, K. L.; Hertenberger, R.; Krü; cken, R.; Leach, K. G.; Schumaker, M. A.; Svensson, C. E.; Wirth, H.-F.; Wong, J.

2009-01-01

The structures of 3+ states in Os have been debated over several decades. Based on measured B(E2) values they were interpreted in 186-192Os as Kπ = 4+ two-phonon vibrations, whereas inelastic scattering, and (t,α) work imply a hexadecapole phonon description. To clarify the nature of these Kπ = 4+ bands in 186,188Os, we performed a (3He,d) reaction on 185,187Re targets using 30 MeV 3He beams and a Q3D spectrograph. Absolute cross sections were obtained for excited states up to 3 MeV at 9 angles from 5° to 50°. Results indicate a significant 5/2+[402]π+3/2+[402]π component in agreement with quasiparticle phonon model predictions for a single hexadecapole phonon structure.

16 CFR 18.6 - Plants collected from the wild state.

Code of Federal Regulations, 2010 CFR

2010-01-01

... NURSERY INDUSTRY § 18.6 Plants collected from the wild state. It is an unfair or deceptive act or practice... nurseries from plants lawfully collected from the wild state may be designated as “nursery-propagated...

Study of transitional doubly-odd /sup 186/Ir and /sup 184/Ir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ben Braham, A.; Bourgeois, C.; Kilcher, P.

1987-12-10

The transitional doubly-odd iridium nuclei with A = 184 and 186 have been studied from the ..beta../sup +//EC decay of the corresponding platinum isotopes using the on-line mass separator ISOCELE. Configurations can be reasonably Attributed to the low-lying states of /sup 184/Ir in agreement with results already known. On the other hand an E3 transition observed in /sup 186/Ir suggests that the known long-lived 1.7h 2/sup -/ state is located at 137.5 keV above the 16h 5/sup +/ state, raising questions about structure of this latter state.

Hafnium-doped hydroxyapatite nanoparticles with ionizing radiation for lung cancer treatment.

PubMed

Chen, Min-Hua; Hanagata, Nobutaka; Ikoma, Toshiyuki; Huang, Jian-Yuan; Li, Keng-Yuan; Lin, Chun-Pin; Lin, Feng-Huei

2016-06-01

Recently, photodynamic therapy (PDT) is one of the new clinical options by generating cytotoxic reactive oxygen species (ROS) to kill cancer cells. However, the optical approach of PDT is limited by tissue penetration depth of visible light. In this study, we propose that a ROS-enhanced nanoparticle, hafnium-doped hydroxyapatite (Hf:HAp), which is a material to yield large quantities of ROS inside the cells when the nanoparticles are bombarded with high penetrating power of ionizing radiation. Hf:HAp nanoparticles are generated by wet chemical precipitation with total doping concentration of 15mol% Hf(4+) relative to Ca(2+) in HAp host material. The results show that the HAp particles could be successfully doped with Hf ions, resulted in the formation of nano-sized rod-like shape and with pH-dependent solubility. The impact of ionizing radiation on Hf:HAp nanoparticles is assessed by using in-vitro and in-vivo model using A549 cell line. The 2',7'-dichlorofluorescein diacetate (DCFH-DA) results reveal that after being exposed to gamma rays, Hf:HAp could significantly lead to the formation of ROS in cells. Both cell viability (WST-1) and cytotoxicity (LDH) assay show the consistent results that A549 lung cancer cell lines are damaged with changes in the cells' ROS level. The in-vivo studies further demonstrate that the tumor growth is inhibited owing to the cells apoptosis when Hf:HAp nanoparticles are bombarded with ionizing radiation. This finding offer a new therapeutic method of interacting with ionizing radiation and demonstrate the potential of Hf:HAp nanoparticles in tumor treatment, such as being used in a palliative treatment after lung surgical procedure. Photodynamic therapy (PDT) is one of the new clinical options by generating cytotoxic reactive oxygen species (ROS) to kill cancer cells. Unfortunately, the approach of PDT is usually limited to the treatment of systemic disease and deeper tumor, due to the limited tissue penetration depth of visible

77 FR 46147 - 57th Meeting: RTCA Special Committee 186, Automatic Dependent Surveillance Broadcast (ADS-B)

Federal Register 2010, 2011, 2012, 2013, 2014

2012-08-02

... 186, Automatic Dependent Surveillance Broadcast (ADS-B) AGENCY: Federal Aviation Administration (FAA..., Automatic Dependent Surveillance Broadcast (ADS-B). SUMMARY: The FAA is issuing this notice to advise the public of the 57th meeting of RTCA Special Committee 186, Automatic Dependent Surveillance Broadcast (ADS...

Rhenium-186 liposomes as convection-enhanced nanoparticle brachytherapy for treatment of glioblastoma

PubMed Central

Phillips, William T.; Goins, Beth; Bao, Ande; Vargas, Daniel; Guttierez, Juan E.; Trevino, Abram; Miller, Jessica R.; Henry, James; Zuniga, Richard; Vecil, Giacomo; Brenner, Andrew J.

2012-01-01

Although external beam radiation is an essential component to the current standard treatment of primary brain tumors, its application is limited by toxicity at doses more than80 Gy. Recent studies have suggested that brachytherapy with liposomally encapsulated radionuclides may be of benefit, and we have reported methods to markedly increase the specific activity of rhenium-186 (186Re)–liposomes. To better characterize the potential delivery, toxicity, and efficacy of the highly specific activity of 186Re-liposomes, we evaluated their intracranial application by convection-enhanced delivery in an orthotopic U87 glioma rat model. After establishing an optimal volume of 25 µL, we observed focal activity confined to the site of injection over a 96-hour period. Doses of up to 1850 Gy were administered without overt clinical or microscopic evidence of toxicity. Animals treated with 186Re-liposomes had a median survival of 126 days (95% confidence interval [CI], 78.4–173 days), compared with 49 days (95% CI, 44–53 days) for controls. Log-rank analysis between these 2 groups was highly significant (P = .0013) and was even higher when 100 Gy was used as a cutoff (P < .0001). Noninvasive luciferase imaging as a surrogate for tumor volume showed a statistically significant separation in bioluminescence by 11 days after 100 Gy or less treatment between the experimental group and the control animals (χ2[1, N= 19] = 4.8; P = .029). MRI also supported this difference in tumor size. Duplication of tumor volume differences and survival benefit was possible in a more invasive U251 orthotopic model, with clear separation in bioluminescence at 6 days after treatment (χ2[1, N= 9] = 4.7; P = .029); median survival in treated animals was not reached at 120 days because lack of mortality, and log-rank analysis of survival was highly significant (P = .0057). Analysis of tumors by histology revealed minimal areas of necrosis and gliosis. These results support the potential

California's Proposition 186: lessons from a single-payer health care reform ballot initiative campaign.

PubMed

Farey, K; Lingappa, V R

1996-01-01

Proposition 186 was an initiative on the November 1994 California ballot which proposed to establish a state single-payer health care program. Although Prop 186 was overwhelmingly defeated in the November 1994 election (73% No, 27% Yes), it accomplished many things. Model legislation was developed showing the feasibility of a specific single-payer program for California. It was placed on the ballot by an unprecedented volunteer signature-gathering effort and was the largest grassroots political campaign fund-raising effort in California history. A novel strategy for the discussion of complex issues through 1500 house parties was launched. Prop 186 was defeated by an insurance industry-led coalition with an anti-government message. Lessons for future efforts include increasing the size and duration of the grassroots organizing and educational effort, and decreasing reliance on conventional political campaign tactics and the mainstream media.

186. Photocopy of drawing, Twin Falls Canal Company, date unknown. ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

186. Photocopy of drawing, Twin Falls Canal Company, date unknown. DRY CREEK RESERVOIR, CASSIA COUNTY (NOW TWIN FALLS COUNTY); MAP. - Milner Dam & Main Canal: Twin Falls Canal Company, On Snake River, 11 miles West of city of Burley, Idaho, Twin Falls, Twin Falls County, ID

The causes for geographical variations in OS187/OS186 at the Cretaceous-Tertiary boundary

NASA Technical Reports Server (NTRS)

Turekian, K. K.; Esser, B. K.; Ravizza, G. E.

1988-01-01

Researchers at Yale has approached the problem of the osmium isotopic composition of marine deposits formed in contact with both oxidized and reduced bottom waters. The measured (187) Os/(186) Os ratios of modern bulk sediment can be explained using mixing equations involving continental detrital, volcaniclastic, cosmogenic and hydrogeneous components. These studies show that sediments deposited under reducing marine conditions contain a hydrogenous component which is enriched in Re and has a radiogenic (187) Os/(186) Os ratio. The presence of such a hydrogenous component in the marine fish clay at Stevns Klint can account for the elevation of its (187) Os/(186) Os ration above the expected meteoritic value. Mass balance considerations require the Re/Os ratio of the phase precipitated from the terminal Cretaceous sea at Stevns Klint to have been about one tenth the value observed in contemporary deposits in the Black Sea, assuming Re has not been lost (or Os gained) subsequent to precipitation. In continental sections, the elevation of the (187) Os/(186) Os ratio in boundary layers may be due to precipitation from continental waters of crustally-derived radiogenic osmium either contemporaneous with the meteoritic (or mantle) osmium deposition or later during diagenesis.

Electron-beam-evaporated thin films of hafnium dioxide for fabricating electronic devices

DOE PAGES

Xiao, Zhigang; Kisslinger, Kim

2015-06-17

Thin films of hafnium dioxide (HfO 2) are widely used as the gate oxide in fabricating integrated circuits because of their high dielectric constants. In this paper, the authors report the growth of thin films of HfO 2 using e-beam evaporation, and the fabrication of complementary metal-oxide semiconductor (CMOS) integrated circuits using this HfO 2 thin film as the gate oxide. The authors analyzed the thin films using high-resolution transmission electron microscopy and electron diffraction, thereby demonstrating that the e-beam-evaporation-grown HfO 2 film has a polycrystalline structure and forms an excellent interface with silicon. Accordingly, we fabricated 31-stage CMOS ringmore » oscillator to test the quality of the HfO 2 thin film as the gate oxide, and obtained excellent rail-to-rail oscillation waveforms from it, denoting that the HfO 2 thin film functioned very well as the gate oxide.« less

Contactin-1 and Neurofascin-155/-186 Are Not Targets of Auto-Antibodies in Multifocal Motor Neuropathy.

PubMed

Doppler, Kathrin; Appeltshauser, Luise; Krämer, Heidrun H; Ng, Judy King Man; Meinl, Edgar; Villmann, Carmen; Brophy, Peter; Dib-Hajj, Sulayman D; Waxman, Stephen G; Weishaupt, Andreas; Sommer, Claudia

2015-01-01

Multifocal motor neuropathy is an immune mediated disease presenting with multifocal muscle weakness and conduction block. IgM auto-antibodies against the ganglioside GM1 are detectable in about 50% of the patients. Auto-antibodies against the paranodal proteins contactin-1 and neurofascin-155 and the nodal protein neurofascin-186 have been detected in subgroups of patients with chronic inflammatory demyelinating polyneuropathy. Recently, auto-antibodies against neurofascin-186 and gliomedin were described in more than 60% of patients with multifocal motor neuropathy. In the current study, we aimed to validate this finding, using a combination of different assays for auto-antibody detection. In addition we intended to detect further auto-antibodies against paranodal proteins, specifically contactin-1 and neurofascin-155 in multifocal motor neuropathy patients' sera. We analyzed sera of 33 patients with well-characterized multifocal motor neuropathy for IgM or IgG anti-contactin-1, anti-neurofascin-155 or -186 antibodies using enzyme-linked immunosorbent assay, binding assays with transfected human embryonic kidney 293 cells and murine teased fibers. We did not detect any IgM or IgG auto-antibodies against contactin-1, neurofascin-155 or -186 in any of our multifocal motor neuropathy patients. We conclude that auto-antibodies against contactin-1, neurofascin-155 and -186 do not play a relevant role in the pathogenesis in this cohort with multifocal motor neuropathy.

12 CFR 303.186 - Exemptions from insurance requirements for a state branch of a foreign bank.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Exemptions from insurance requirements for a state branch of a foreign bank. 303.186 Section 303.186 Banks and Banking FEDERAL DEPOSIT INSURANCE... insurance requirements for a state branch of a foreign bank. (a) Filing procedures—(1) Where to file. An...

Post-hoc analysis of MCI186-17, the extension study to MCI186-16, the confirmatory double-blind, parallel-group, placebo-controlled study of edaravone in amyotrophic lateral sclerosis.

PubMed

Takahashi, Fumihiro; Takei, Koji; Tsuda, Kikumi; Palumbo, Joseph

2017-10-01

In the 24-week double-blind study of edaravone in ALS (MCI186-16), edaravone did not show a statistically significant difference versus placebo for the primary efficacy endpoint. For post-hoc analyses, two subpopulations were identified in which edaravone might be expected to show efficacy: the efficacy-expected subpopulation (EESP), defined by scores of ≥2 points on all 12 items of the ALS Functional Rating Scale-Revised (ALSFRS-R) and a percent predicted forced vital capacity (%FVC) ≥80% at baseline; and the definite/probable EESP 2 years (dpEESP2y) subpopulation which, in addition to EESP criteria, had definite or probable ALS diagnosed by El Escorial revised criteria, and disease duration of ≤2 years. In the 36-week extension study of MCI186-16, a 24-week double-blind comparison followed by 12 weeks of open-label edaravone (MCI186-17; NCT00424463), analyses of ALSFRS-R scores of the edaravone-edaravone group and edaravone-placebo group for the full analysis set (FAS) and EESP, as prospectively defined, were reported in a previous article. Here we additionally report results in patients who met dpEESP2y criteria at the baseline of MCI186-16. In the dpEESP2y, the difference in ALSFRS-R changes from 24 to 48 weeks between the edaravone-edaravone and edaravone-placebo groups was 2.79 (p = 0.0719), which was greater than the differences previously reported for the EESP and the FAS. The pattern of adverse events in the dpEESP2y did not show any additional safety findings to those from the earlier prospective study. In conclusion, this post-hoc analysis suggests a potential effect of edaravone between 24 and 48 weeks in patients meeting dpEESP2y criteria at baseline.

186. Photographic copy of original construction drawing dated March 28, ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

186. Photographic copy of original construction drawing dated March 28, 1932 (from Record Group 115, Denver Branch of the National Archives, Denver). VOLUME CHANGE IN MASS CONCRETE; OWYHEE DAM CONCRETE RESEARCH FOR HOOVER DAM; MISCELLANEOUS VERTICAL SECTIONS; THROUGH PANELS. - Owyhee Dam, Across Owyhee River, Nyssa, Malheur County, OR

Effect of nitrogen on tensile properties and structures of T-111 (tantalum, 8 percent tungsten, 2 percent hafnium) tubing

NASA Technical Reports Server (NTRS)

Buzzard, R. J.; Metroka, R. R.

1973-01-01

The effect of controlled nitrogen additions was evaluated on the mechanical properties of T-111 (Ta-8W-2Hf) fuel pin cladding material proposed for use in a lithium-cooled nuclear reactor concept. Additions of 80 to 1125 ppm nitrogen resulted in increased strengthening of T-111 tubular section test specimens at temperatures of 25 to 1200 C. Homogeneous distributions of up to 500 ppm nitrogen did not seriously decrease tensile ductility. Both single and two-phase microstructures, with hafnium nitride as the second phase, were evaluated in this study.

Deuteron irradiation of W and WO 3 for production of high specific activity 186Re: Challenges associated with thick target preparation

DOE PAGES

Balkin, Ethan R.; Gagnon, Katherine; Strong, Kevin T.; ...

2016-06-28

This investigation evaluated target fabrication and beam parameters for scale-up production of high specific activity 186Re using deuteron irradiation of enriched 186W via the 186W(d,2n) 186Re reaction. Thick W and WO 3 targets were prepared, characterized and evaluated in deuteron irradiations. Full-thickness targets, as determined using SRIM, were prepared by uniaxi-ally pressing powdered natural abundance W and WO 3, or 96.86% enriched 186W, into Al target supports. Alternatively, thick targets were prepared by pressing 186W between two layers of graphite powder or by placing pre-sintered (1105°C, 12 hours) natural abundance WO 3 pellets into an Al target support. Assessments ofmore » structural integrity were made on each target pre-pared. Prior to irradiation, material composition analyses were conducted using SEM, XRD, and Raman spectroscopy. With-in a minimum of 24 hours post irradiation, gamma-ray spectroscopy was performed on all targets to assess production yields and radionuclidic byproducts. Problems were encountered with the structural integrity of some pressed W and WO 3 pellets before and during irradiation, and target material characterization results could be correlated with the structural integrity of the pressed target pellets. Under the conditions studied, the findings suggest that all WO 3 targets prepared and studied were unacceptable. By contrast, 186W metal was found to be a viable target material for 186Re production. Lastly, thick targets prepared with powdered 186W pressed between layers of graphite provided a particularly robust target configuration.« less

Deuteron irradiation of W and WO3 for production of high specific activity (186)Re: Challenges associated with thick target preparation.

PubMed

Balkin, Ethan R; Gagnon, Katherine; Strong, Kevin T; Smith, Bennett E; Dorman, Eric F; Emery, Robert C; Pauzauskie, Peter J; Fassbender, Michael E; Cutler, Cathy S; Ketring, Alan R; Jurisson, Silvia S; Wilbur, D Scott

2016-09-01

This investigation evaluated target fabrication and beam parameters for scale-up production of high specific activity (186)Re using deuteron irradiation of enriched (186)W via the (186)W(d,2n)(186)Re reaction. Thick W and WO3 targets were prepared, characterized and evaluated in deuteron irradiations. Full-thickness targets, as determined using SRIM, were prepared by uniaxially pressing powdered natural abundance W and WO3, or 96.86% enriched (186)W, into Al target supports. Alternatively, thick targets were prepared by pressing (186)W between two layers of graphite powder or by placing pre-sintered (1105°C, 12h) natural abundance WO3 pellets into an Al target support. Assessments of structural integrity were made on each target prepared. Prior to irradiation, material composition analyses were conducted using SEM, XRD, and Raman spectroscopy. Within a minimum of 24h post irradiation, gamma-ray spectroscopy was performed on all targets to assess production yields and radionuclidic byproducts. Problems were encountered with the structural integrity of some pressed W and WO3 pellets before and during irradiation, and target material characterization results could be correlated with the structural integrity of the pressed target pellets. Under the conditions studied, the findings suggest that all WO3 targets prepared and studied were unacceptable. By contrast, (186)W metal was found to be a viable target material for (186)Re production. Thick targets prepared with powdered (186)W pressed between layers of graphite provided a particularly robust target configuration. Copyright © 2016 Elsevier Ltd. All rights reserved.

Pyroelectric response in crystalline hafnium zirconium oxide (Hf 1- x Zr x O 2 ) thin films

DOE PAGES

Smith, S. W.; Kitahara, A. R.; Rodriguez, M. A.; ...

2017-02-13

Pyroelectric coefficients were measured for 20 nm thick crystalline hafnium zirconium oxide (Hf 1-xZr xO 2) thin films across a composition range of 0 ≤ x ≤ 1. Pyroelectric currents were collected near room temperature under zero applied bias and a sinusoidal oscillating temperature profile to separate the influence of non-pyroelectric currents. The pyroelectric coefficient was observed to correlate with zirconium content, increased orthorhombic/tetragonal phase content, and maximum polarization response. The largest measured absolute value was 48 μCm -2K -1 for a composition with x = 0.64, while no pyroelectric response was measured for compositions which displayed no remanent polarizationmore » (x = 0, 0.91, 1).« less

Techniques for Loading Technetium-99m and Rhenium-186/188 Radionuclides into Preformed Liposomes for Diagnostic Imaging and Radionuclide Therapy.

PubMed

Goins, Beth; Bao, Ande; Phillips, William T

2017-01-01

Liposomes can serve as carriers of radionuclides for diagnostic imaging and therapeutic applications. Herein, procedures are outlined for radiolabeling liposomes with the gamma-emitting radionuclide, technetium-99m ( 99m Tc), for noninvasive detection of disease and for monitoring the pharmacokinetics and biodistribution of liposomal drugs, and/or with therapeutic beta-emitting radionuclides, rhenium-186/188 ( 186/188 Re), for radionuclide therapy. These efficient and practical liposome radiolabeling methods use a post-labeling mechanism to load 99m Tc or 186/188 Re into preformed liposomes prepared in advance of the labeling procedure. For all liposome radiolabeling methods described, a lipophilic chelator is used to transport 99m Tc or 186/188 Re across the lipid bilayer of the preformed liposomes. Once within the liposome interior, the pre-encapsulated glutathione or ammonium sulfate (pH) gradient provides for stable entrapment of the 99m Tc and 186/188 Re within the liposomes. In the first method, 99m Tc is transported across the lipid bilayer by the lipophilic chelator, hexamethylpropyleneamine oxime (HMPAO) and 99m Tc-HMPAO becomes trapped by interaction with the pre-encapsulated glutathione within the liposomes. In the second method, 99m Tc or 186/188 Re is transported across the lipid bilayer by the lipophilic chelator, N,N-bis(2-mercaptoethyl)-N',N'-diethylethylenediamine (BMEDA), and 99m Tc-BMEDA or 186/188 Re-BMEDA becomes trapped by interaction with pre-encapsulated glutathione within the liposomes. In the third method, an ammonium sulfate (pH) gradient loading technique is employed using liposomes with an extraliposomal pH of 7.4 and an interior pH of 5.1. BMEDA, which is lipophilic at pH 7.4, serves as a lipophilic chelator for 99m Tc or 186/188 Re to transport the radionuclides across the lipid bilayer. Once within the more acidic liposome interior, 99m Tc/ 186/188 Re-BMEDA complex becomes protonated and more hydrophilic, which results in stable

Rhenium‐186‐mercaptoacetyltriglycine‐labeled Monoclonal Antibody for Radioimmunotherapy: In vitro Assessment, in vivo Kinetics and Dosimetry in Tumor‐bearing Nude Mice

PubMed Central

Yokoyama, Kunihiko; Tega, Harunobu; Hiramatsu, Takashi; Konishi, Shota; Yamamoto, Wakako; Shuke, Noriyuki; Aburano, Tamio; Watanabe, Naoto; Takayama, Terahiko; Michigishi, Takatoshi; Tonami, Norihisa

1998-01-01

Stability and immunoreactivity of 186Re‐labeled monoclonal antibody were examined, and its in vivo kinetics was investigated in tumor‐bearing Balb/c nu/nu female mice to assess the feasibility of using it in radioimmunotherapy (RIT). A murine IgG1, A7, against a 45 kD glycoprotein in human colon cancer was radiolabeled with 186Re by using a chelating method with a mercaptoacetyltriglycine (MAG3). 186Re‐MAG3 complex was conjugated to A7 after esterification of 186Re‐MAG3 with tetrafluorophenol (TFP). The efficiency of 186Re‐MAG3‐TFP production and the labeling efficiency of A7 were 51–59% and 57–60%, respectively. Immunoreactivity of purified 186Re‐MAG3‐A7 was 68.2% at infinite antigen excess. In 0.9% NaCl at 4°C, the radioactivity (12.7 MBq/mg, 3.55 MBq/ml) dissociated with time from 186Re‐MAG3‐A7 as a small molecular weight moiety because of autoradiolysis. The addition of ascorbic acid, 5 mg/ml, as a radioprotectant or storage at –80°C could effectively prevent the radiolysis of 186Re‐MAG3‐A7 for 7 days. Immunoreactivity of 186Re‐MAG3‐A7, 6.70 MBq/mg (6.66 MBq/ml), stored in the presence of ascorbic acid was well retained up to 8 days after the preparation. In colon cancer xenografted mice, 31.0% of the injected dose/g of 186Re‐MAG3‐A7 had accumulated in the tumors at 24 h postinjection. Estimated radiation dose to tumors was 14.9 cGy/37 kBq up to 8 days postinjection which was 12‐fold greater than the whole‐body radiation dose. These in vivo characteristics were superior to those of A7 labeled with radioiodine, affording greater therapeutic ratios than 131I‐A7. Because of the better image quality of 186Re‐MAG3‐A7 as well as more favorable dosimetry, 186Re‐MAG3‐A7 would be a better choice for RIT of colon cancer than 131I‐A7. These results indicated the feasibility of RIT with 186Re‐MAG3‐A7, though the prevention of radiolysis of the labeled antibody should be considered. PMID:9765625

Pox 186: An ultracompact galaxy with dominant ionized gas emission

NASA Astrophysics Data System (ADS)

Guseva, N. G.; Papaderos, P.; Izotov, Y. I.; Noeske, K. G.; Fricke, K. J.

2004-07-01

We present a ground-based optical spectroscopic and HST U, V, I photometric study of the blue compact dwarf (BCD) galaxy Pox 186. It is found that the emission of the low-surface brightness (LSB) component in Pox 186 at radii ⪉3 arcsec (⪉270 pc in linear scale) is mainly gaseous in origin. We detect Hα emission out to radii as large as 6 arcsec. At radii ⪆3 arcsec the light of the LSB component is contaminated by the emission of background galaxies complicating the study of the outermost regions. The surface brightness distribution in the LSB component can be approximated by an exponential law with a scale length α ⪉ 120 pc. This places Pox 186 among the most compact dwarf galaxies known. The derived α is likely to be an upper limit to the scale length of the LSB component because of the strong contribution of the gaseous emission. The oxygen abundance in the bright H II region derived from the 4.5 m Multiple Mirror Telescope (MMT) and 3.6 m ESO telescope spectra are 12 + log (O/H) = 7.76 ± 0.02 and 7.74 ± 0.01 (˜Z⊙/15), respectively, in accordance with previous determinations. The helium mass fractions found in this region are Y = 0.248 ± 0.009 (MMT) and Y = 0.248 ± 0.004 (3.6 m) suggesting a high primordial helium abundance. The MMT Observatory is a joint facility of the Smithsonian Institution and the University of Arizona. Based on observations collected at the European Southern Observatory, Chile, ESO program 71.B-0032(A). 12+\\log(O/H)⊙ = 8.92 (Anders & Grevesse \\cite{Anders89}).

Tribo-electrochemical characterization of hafnium multilayer systems deposited on nitride/vanadium nitride AISI 4140 steel

NASA Astrophysics Data System (ADS)

Mora, M.; Vera, E.; Aperador, W.

2016-02-01

In this work is presented the synergistic behaviour among corrosion/wear (tribocorrosion) of the multilayer coatings hafnium nitride/vanadium nitride [HfN/VN]n. The multilayers were deposited on AISI 4140 steel using the technique of physical vapor deposition PVD magnetron sputtering, the tests were performed using a pin-on-disk tribometer, which has an adapted potentiostat galvanostat with three-electrode electrochemical cell. Tribocorrosive parameters such as: Friction coefficient between the coating and the counter body (100 Cr6 steel ball); Polarization resistance by means of electrochemical impedance spectroscopy technique and corrosion rate by polarization curves were determined. It was observed an increase in the polarization resistance, a decrease in the corrosion rate and a low coefficient of friction in comparison with the substrate, due to an increase on the number of bilayers.

Synthesis of High Symmetry Phase of Hafnium Dioxide Thin Films and Nickel Ferrite's Effect on Microstructure in Composite Heterostructure

NASA Astrophysics Data System (ADS)

Straka, Weston J.

Hafnium dioxide has attracted a great deal of attention recently due to its potential use in two different electronic applications: CMOS and FeRAM. In CMOS, the usefulness of hafnia comes in due to its high dielectric constant and compatibility with current IC processing parameters. For FeRAM, hafnia's recent discovery to exhibit ferroelectricity in an orthorhombic phase makes this material attractive for replacement of the ferroelectric material in FeRAM. This study shows the feasibility of depositing thin films of hafnium oxide via chemical solution deposition for integration into these devices. The processing parameters necessary to produce this phase show how non-equilibrium processing plays a role in its synthesis. The temperature necessary to achieve the high symmetry phase was at 725 °C for 3 minutes on sapphire, silicon, and coated silicon substrates. The thermal conductivity of each was viewed as the property that allowed the hafnia formation. The dielectric constant of the hafnia films were between 30 and 32 with low dissipation factors and up to 47 with a poor dissipation factor all at 1 kHz. The formation of this phase was shown to be thickness independent with the high symmetry phase existing up to 300 nm film thickness. Interfacing the hafnia film with nickel ferrite was also studied to identify the possibility of using this composite for non-destructive reading of FeRAM. The magnetic properties showed an unchanged nickel ferrite film but the interface between the two was poor leading to the conclusion that more work must be done to successfully integrate these two films.

Level Structure Above the T1/2 = 2 . 0 ×105 yr Isomer in 186Re

NASA Astrophysics Data System (ADS)

Matters, D. A.; McClory, J. W.; Kondev, F. G.; Carpenter, M. P.; Carroll, J. J.; Chiara, C. J.; Lane, G. J.; Kibédi, T.; Ideguchi, E.; Fang, Y.; Watanabe, H.; E435 Cagra Collaboration

2016-03-01

The level structure above the Kπ = (8+) , 149-keV isomer in 186Re is largely undeveloped. The isomer could play a role in the s-process nucleosynthesis of 187Os and 187Re and affect the accuracy of the Re-Os cosmochronometer. An experiment was conducted at the Research Center for Nuclear Physics (RCNP) at Osaka University, Japan, using the Clover Array Gamma-ray spectrometer at RCNP/RIBF for Advanced research (CAGRA) to measure γ-ray coincidences from (d , 2 n) reactions on an enriched 186W target. The γ - γ coincidence data obtained from the CAGRA array were analyzed along with data from a similar experiment performed in 2006 at the Australian National University. A preliminary analysis of the data reveals several new levels and transitions feeding the 186mRe isomer.

27 CFR 17.186 - Transfer of distilled spirits to other containers.

Code of Federal Regulations, 2014 CFR

2014-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Transfer of distilled... USED IN MANUFACTURING NONBEVERAGE PRODUCTS Miscellaneous Provisions § 17.186 Transfer of distilled spirits to other containers. A manufacturer may transfer taxpaid distilled spirits from the original...

Determination of (187)Os in molybdenite by ICP-MS with neutron-induced (186)Os and (188)Os spikes.

PubMed

Qu, W; Du, A; Zhao, D

2001-10-31

The article describes a method for the determination of (187)Os in molybdenite by isotope dilution inductively coupled plasma-mass spectrometry (ID-ICP-MS) with neutron-induced (186)Os and (188)Os spike. The spike used in the present work was prepared in line with the principle by which artificial nuclides are produced in a nuclear reaction. The concentration and isotopic composition of osmium in the prepared spike were evaluated accurately with the isotope dilution method, using negative thermal ion mass spectrometry (N-TIMS). The advantage of this method is that using (186)Os and (188)Os double spikes can effectively compensate for the mass discrimination effects of ICP-MS. Thus, the common correction practice for mass bias in the isotope dilution method with a single spike is unnecessary. In addition, the method enables one to reduce the determined error arising from instrumental instability. The precision for the (187)Os/((186)Os+(188)Os) ratio was approximately 2% (2sigma, RSD), but in the case of (187)Os/(186)Os, (187)Os/(188)Os and (186)Os/(188)Os, precision ranged from 2.0 to 8% (2sigma, RSD). The results for (187)Os concentration in a molybdenite sample determined with this method showed good agreement with reference values.

Hafnium Films and Magnetic Shielding for TIME, A mm-Wavelength Spectrometer Array

NASA Astrophysics Data System (ADS)

Hunacek, J.; Bock, J.; Bradford, C. M.; Butler, V.; Chang, T.-C.; Cheng, Y.-T.; Cooray, A.; Crites, A.; Frez, C.; Hailey-Dunsheath, S.; Hoscheit, B.; Kim, D. W.; Li, C.-T.; Marrone, D.; Moncelsi, L.; Shirokoff, E.; Steinbach, B.; Sun, G.; Trumper, I.; Turner, A.; Uzgil, B.; Weber, A.; Zemcov, M.

2018-04-01

TIME is a mm-wavelength grating spectrometer array that will map fluctuations of the 157.7-μm emission line of singly ionized carbon ([CII]) during the epoch of reionization (redshift z ˜ 5-9). Sixty transition-edge sensor (TES) bolometers populate the output arc of each of the 32 spectrometers, for a total of 1920 detectors. Each bolometer consists of gold absorber on a ˜ 3 × 3 mm silicon nitride micro-mesh suspended near the corners by 1 × 1 × 500 μm silicon nitride legs targeting a photon-noise-dominated NEP ˜ 1 × 10^{-17} W/√{Hz} . Hafnium films are explored as a lower-T_c alternative to Ti (500 mK) for TIME TESs, allowing thicker support legs for improved yield. Hf T_c is shown to vary between 250 and 450 mK when varying the resident Ar pressure during deposition. Magnetic shielding designs and simulations are presented for the TIME first-stage SQUIDs. Total axial field suppression is predicted to be 5 × 10^7.

Techniques for loading technetium-99m and rhenium-186/188 radionuclides into pre-formed liposomes for diagnostic imaging and radionuclide therapy.

PubMed

Goins, Beth; Bao, Ande; Phillips, William T

2010-01-01

Liposomes can serve as carriers of radionuclides for diagnostic imaging and therapeutic applications. Herein, procedures are outlined for radiolabeling liposomes with the gamma-emitting radionuclide, technetium-99m ((99m)Tc), for non-invasive detection of disease and for monitoring the pharmacokinetics and biodistribution of liposomal drugs, and/or with therapeutic beta-emitting radionuclides, rhenium-186/188 ((186/188)Re), for radionuclide therapy. These efficient and practical liposome radiolabeling methods use a post-labeling mechanism to load (99m)Tc or (186/188)Re into pre-formed liposomes prepared in advance of the labeling procedure. For all liposome radiolabeling methods described, a lipophilic chelator is used to transport (99m)Tc or (186/188)Re across the lipid bilayer of the pre-formed liposomes. Once within the liposome interior, the pre-encapsulated glutathione or ammonium sulfate (pH) gradient provides for stable entrapment of the (99m)Tc and (186/188)Re within the liposomes. In the first method, (99m)Tc is transported across the lipid bilayer by the lipophilic chelator, hexamethylpropyleneamine oxime (HMPAO) and (99m)Tc-HMPAO becomes trapped by interaction with the pre-encapsulated glutathione within the liposomes. In the second method, (99m)Tc or (186/188)Re is transported across the lipid bilayer by the lipophilic chelator, N,N-bis(2-mercaptoethyl)-N',N'-diethylethylenediamine (BMEDA), and (99m)Tc-BMEDA or (186/188)Re-BMEDA becomes trapped by interaction with pre-encapsulated glutathione within the liposomes. In the third method, an ammonium sulfate (pH) gradient loading technique is employed using liposomes with an extraliposomal pH of 7.4 and an interior pH of 5.1. BMEDA, which is lipophilic at pH 7.4, serves as a lipophilic chelator for (99m)Tc or (186/188)Re to transport the radionuclides across the lipid bilayer. Once within the more acidic liposome interior, (99m)Tc/(186/188)Re-BMEDA complex becomes protonated and more hydrophilic, which

Tracing the history of submarine hydrothermal inputs and the significance of hydrothermal hafnium for the seawater budget - A combined Pb-Hf-Nd isotope approach

USGS Publications Warehouse

van de Flierdt, T.; Frank, M.; Halliday, A.N.; Hein, J.R.; Hattendorf, B.; Gunther, D.; Kubik, P.W.

2004-01-01

Secular variations in the Pb isotopic composition of a mixed hydrogenous-hydrothermal ferromanganese crust from the Bauer Basin in the eastern Equatorial Pacific provide clear evidence for changes in hydrothermal contributions during the past 7 Myr. The nearby Galapagos Rise spreading center provided a strong hydrothermal flux prior to 6.5 Ma. After 6.5 Ma, the Pb became stepwise more radiogenic and more similar to Equatorial Pacific seawater, reflecting the westward shift of spreading to the presently active East Pacific Rise (EPR). A second, previously unrecognized enhanced hydrothermal period occurred between 4.4 and 2.9 Ma, which reflects either off-axis hydrothermal activity in the Bauer Basin or a late-stage pulse of hydrothermal Pb from the then active, but waning Galapagos Rise spreading center. Hafnium isotope time-series of the same mixed hydrogenous-hydrothermal crust show invariant values over the past 7 Myr. Hafnium isotope ratios, as well as Nd isotope ratios obtained for this crust, are identical to that of hydrogenous Equatorial Pacific deep water crusts and clearly indicate that hydrothermal Hf, similar to Nd, does not travel far from submarine vents. Therefore, we suggest that hydrothermal Hf fluxes do not contribute significantly to the global marine Hf budget. ?? 2004 Elsevier B.V. All rights reserved.

TUG1 mediates methotrexate resistance in colorectal cancer via miR-186/CPEB2 axis.

PubMed

Li, Changfeng; Gao, Yongjian; Li, Yongchao; Ding, Dayong

2017-09-16

Colorectal cancer (CRC) is a common malignancy, most of which remain unresponsive to chemotherapy. Methotrexate (MTX) is one of the earliest cytotoxic drugs and serves as an anti-metabolite and anti-folate chemotherapy for various types of cancer. However, MTX resistance prevents its clinical application in cancer therapy. Thereby, overcoming the drug resistance is an alternative strategy to maximize the efficacy of MTX therapies in clinics. Long non-coding RNAs (lncRNAs) have gained widespread attention in recent years. More and more evidences have shown that lncRNAs play regulatory roles in various biological activities and disease progression including drug resistance in cancer cells. Here, we observed lncRNA TUG1 was associated to the MTX resistant in colorectal cancer cells. Firstly, quantitative analysis indicated that TUG1 was significantly increased in tumors which were resistant to MTX treatment. TUG1 knockdown re-sensitized the MTX resistance in colorectal cancer cells, which were MTX-resistant colorectal cell line. Furthermore, bioinformatics analysis showed that miR-186 could directly bind to TUG1, suggesting TUG1 might worked as a ceRNA to sponge miR-186. Extensively, our study also showed that CPEB2 was the direct target of miR-186 in colorectal cancer cells. Taken together, our study suggests that lncRNA TUG1 mediates MTX resistance in colorectal cancer via miR-186/CPEB2 axis. Copyright © 2017. Published by Elsevier Inc.

Sources of osmium to the modern oceans: New evidence from the 190Pt-186Os system

USGS Publications Warehouse

McDaniel, D.K.; Walker, R.J.; Hemming, S.R.; Horan, M.F.; Becker, H.; Grauch, R.I.

2004-01-01

High precision Os isotope analysis of young marine manganese nodules indicate that whereas the composition of modern seawater is radiogenic with respect to 187Os/188Os, it has 186Os/188Os that is within uncertainty of the chondritic value. Marine Mn nodule compositions thus indicate that the average continental source of Os to modern seawater had long-term high Re/Os compared to Pt/Os. Analyses of loess and freshwater Mn nodules support existing evidence that average upper continental crust (UCC) has resolvably suprachondritic 186Os/188Os, as well as radiogenic 187Os/188Os. Modeling the composition of seawater as a two-component mixture of oceanic/cosmic Os with chondritic Os compositions and continentally-derived Os demonstrates that, insofar as estimates for the composition of average UCC are accurate, congruently weathered average UCC cannot be the sole continental source of Os to seawater. Our analysis of four Cambrian black shales confirm that organic-rich sediments can have 187Os/188Os ratios that are much higher than average UCC, but 186Os/188Os compositions that are generally between those of chondrites and average-UCC. Preferential weathering of black shales can result in dissolved Os discharged to the ocean basins that has a much lower 186Os/188Os than does average upper crust. Modeling the available data demonstrates that augmentation of estimated average UCC compositions with less than 0.1% additional black shale and 1.4% additional ultramafic rock can produce a continental end-member Os isotopic composition that satisfies the requirements imposed by the marine Mn nodule data. The interplay of these two sources provides a mechanism by which the 187Os/188Os of seawater can change as sources and weathering conditions change, yet seawater 186Os/188Os varies only minimally. ?? 2004 Elsevier Ltd.

Low-voltage high-performance organic thin film transistors with a thermally annealed polystyrene/hafnium oxide dielectric

NASA Astrophysics Data System (ADS)

Wang, Ying; Acton, Orb; Ting, Guy; Weidner, Tobias; Ma, Hong; Castner, David G.; Jen, Alex K.-Y.

2009-12-01

Low-voltage pentacene-based organic thin film transistors (OTFTs) are demonstrated with polystyrene (PS)/hafnium oxide (HfOx) hybrid dielectrics. Thermal annealing of PS films on HfOx at 120 °C (PS-120) induces a flatter orientation of the phenyl groups (tilt angle 65°) at the surface compared to PS films without annealing (PS-RT) (tilt angle 31°). The flatter phenyl group orientation leads to better matching of surface energy between pentacene and PS. Pentacene deposited on PS-120 display higher quality thin films with larger grain sizes and higher crystallinity. Pentacene OTFTs with PS-120/HfOx hybrid dielectrics can operate at low-voltage (<3 V) with high field-effect mobilities (1 cm2/V s), high on/off current ratios (106), and low subthreshold slopes (100 mV/dec).

Passivation of InP heterojunction bipolar transistors by strain controlled plasma assisted electron beam evaporated hafnium oxide

NASA Astrophysics Data System (ADS)

Driad, R.; Sah, R. E.; Schmidt, R.; Kirste, L.

2012-01-01

We present structural, stress, and electrical properties of plasma assisted e-beam evaporated hafnium dioxide (HfO2) layers on n-type InP substrates. These layers have subsequently been used for surface passivation of InGaAs/InP heterostructure bipolar transistors either alone or in combination with plasma enhanced chemical vapor deposited SiO2 layers. The use of stacked HfO2/SiO2 results in better interface quality with InGaAs/InP heterostructures, as illustrated by smaller leakage current and improved breakdown voltage. These improvements can be attributed to the reduced defect density and charge trapping at the dielectric-semiconductor interface. The deposition at room temperature makes these films suitable for sensitive devices.

MicroRNA-186 promotes macrophage lipid accumulation and secretion of pro-inflammatory cytokines by targeting cystathionine γ-lyase in THP-1 macrophages.

PubMed

Yao, Yan; Zhang, Xin; Chen, Hai-Peng; Li, Liang; Xie, Wei; Lan, Gang; Zhao, Zhen-Wang; Zheng, Xi-Long; Wang, Zong-Bao; Tang, Chao-Ke

2016-07-01

Several studies suggest that cardiomyocyte-enriched miR-186 is involved in cardiac injury and myocardial infarction, and also plays an important role in atherosclerotic diseases, but the underlying mechanism is unknown. Cystathionine-γ-lyase (CSE) is the predominant enzyme to produce H2S in the cardiovascular system. Here, miR-186 was identified to bind to the 3'UTR of CSE. In this study, we aimed at exploring whether miR-186 affects lipid accumulation and secretion of pro-inflammatory cytokines by targeting CSE and its underlying mechanism in human THP-1 macrophages and peripheral blood monocyte-derived macrophages (PBMDM). PBMDM just as a control group for the comparison with the THP-1 macrophages. MiR-186 target genes, CSE 3'UTR sequence and free energy were predicted and analyzed by bioinformatics analyses and dual-luciferase reporter assays. The expression of CSE mRNA and protein were measured by real-time quantitative PCR and western blot analyses. The lipid accumulation in THP-1 macrophages was detected by high performance liquid chromatography (HPLC). The effects of miR-186 on secretion of IL-6, IL-1β and TNF-α were examined by ELISA. Endogenous H2S was detected by spectrophotometry. Using small interfering RNA (siRNA) approach to decrease the expression of CSE protein and mRNA. We found that miR-186 directly inhibited CSE protein and mRNA expression through targeting CSE 3'UTR by bioinformatics analyses and dual-luciferase reporter assays. HPLC assays showed that miR-186 increased the lipid accumulation in human THP-1 macrophages. We also showed that miR-186 enhanced secretion of pro-inflammatory cytokines in human THP-1 macrophages. Using siRNA approach, we found that CSE siRNA could inhibit the miR-186 inhibitor-induced decrease in the expression of LPL protein and mRNA in human THP-1 macrophages, which was accompanied a decrease in the level of H2S. MicroRNA-186 promotes macrophage lipid accumulation and pro-inflammatory cytokine secretion by

Cesium hafnium chloride: A high light yield, non-hygroscopic cubic crystal scintillator for gamma spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Burger, Arnold, E-mail: aburger@fisk.edu; Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37235; Rowe, Emmanuel

We report on the scintillation properties of Cs{sub 2}HfCl{sub 6} (cesium hafnium chloride or CHC) as an example of a little-known class of non-hygroscopic compounds having the generic cubic crystal structure of K{sub 2}PtCl{sub 6}. The crystals are easily growable from the melt using the Bridgman method with minimal precursor treatments or purification. CHC scintillation is centered at 400 nm, with a principal decay time of 4.37 μs and a light yield of up to 54 000 photons/MeV when measured using a silicon CCD photodetector. The light yield is the highest ever reported for an undoped crystal, and CHC also exhibits excellent lightmore » yield nonproportionality. These desirable properties allowed us to build and test CHC gamma-ray spectrometers providing energy resolution of 3.3% at 662 keV.« less

186Os- 187Os systematics of Gorgona Island komatiites: implications for early growth of the inner core

NASA Astrophysics Data System (ADS)

Brandon, Alan D.; Walker, Richard J.; Puchtel, Igor S.; Becker, Harry; Humayun, Munir; Revillon, Sidonie

2003-02-01

The presence of coupled enrichments in 186Os/ 188Os and 187Os/ 188Os in some mantle-derived materials reflects long-term elevation of Pt/Os and Re/Os relative to the primitive upper mantle. New Os data for the 89 Ma Gorgona Island, Colombia komatiites indicate that these lavas are also variably enriched in 186Os and 187Os, with 186Os/ 188Os ranging between 0.1198397±22 and 0.1198470±38, and with γOs correspondingly ranging from +0.15 to +4.4. These data define a linear trend that converges with the previously reported linear trend generated from data for modern Hawaiian picritic lavas and a sample from the ca. 251 Ma Siberian plume, to a common component with a 186Os/ 188Os of approximately 0.119870 and γOs of +17.5. The convergence of these data to this Os isotopic composition may imply a single ubiquitous source in the Earth's interior that mixes with a variety of different mantle compositions distinguished by variations in γOs. The 187Os- and 186Os-enriched component may have been generated via early crystallization of the solid inner core and consequent increases in Pt/Os and Re/Os in the liquid outer core, with time leading to suprachondritic 186Os/ 188Os and γOs in the outer core. The presence of Os from the outer core in certain portions of the mantle would require a mechanism that could transfer Os from the outer core to the lower mantle, and thence to the surface. If this is the process that generated the isotopic enrichments in the mantle sources of these plume-derived systems, then the current understanding of solid metal-liquid metal partitioning of Pt, Re and Os requires that crystallization of the inner core began prior to 3.5 Ga. Thus, the Os isotopic data reported here provide a new source of data to better constrain the timing of inner core formation, complementing magnetic field paleo-intensity measurements as data sources that constrain models based on secular cooling of the Earth.

In vitro comparison of the antiproliferative effects of rhenium-186 and rhenium-188 on human aortic endothelial cells.

PubMed

Sauter, Alexander; Arthasana, Daniel; Dittmann, Helmut; Pritzkow, Maren; Wiesinger, Benjamin; Schmehl, Joerg; Brechtel, Klaus; Bantleon, Rüdiger; Claussen, Claus; Kehlbach, Rainer

2011-08-01

Rhenium-186 ((186)Re) and rhenium-188 ((188)Re) are promising radionuclides for the inhibition of restenosis after percutaneous transluminal angioplasty or other vascular interventions. Until now the maximal dose tolerance of endothelial cells has not been clearly known. To characterize the effects of local irradiation treatment, human aortic endothelial cells (ECs) were incubated with different doses of (186)Re and (188)Re. Two days after plating, ECs received treatment for a period of 5 days. The total radiation doses applied were 1, 4, 8, 16, and 32 Gy. On days 1, 3, 5, 7, and 12 after initial rhenium incubation, cell growth, clonogenic activity, cell-cycle distribution, and cytoskeletal architecture were evaluated. From the first day on, a dose-dependent growth inhibition was observed. Cumulative doses of ≥32 Gy caused a weak colony formation and significant alterations in the cytoskeletal architecture. An increased fraction of cells in G2/M phase was seen for cumulative radiation doses of ≥16 Gy. Interestingly, there were no significant differences between (186)Re and (188)Re. Even for low dose rates of β particles a dose-dependent proliferation inhibition of ECs is seen. Doses beyond 32 Gy alter the cytoskeletal architecture with possibly endothelial dysfunction and late thrombosis.

Isolation of tungsten and tantalum isotopes without supports from. cap alpha. -particle-irradiated hafnium targets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gasita, S.M.; Iota, B.Z.; Malachkov, A.G.

1985-11-01

An extraction procedure has been developed for successive isolation of tungsten (/sup 178/W and /sup 181/W) and tantalum (/sup 179/Ta and /sup 182/Ta) isotopes without supports from ..cap alpha..particle-irradiated hafnium targets. The target, irradiated on a cyclotron, is dissolved in hydrofluoric acid. Tantalum isotopes are extracted with tributyl phosphate (TBP) from 1-5 M HF and are then reextracted with a 1:1 ammonia solution, and hydrofluoric acid is removed by heating. Tungsten isotopes are extracted with a chloroform solution or N-benzoyl-N-phenylhydroxylamine (BPHA) from 11-12 M H/sub 2/SO/sub 4/ or ..cap alpha..-benzoin oxime from 4.5-5.5 M H/sub 2/SO/sub 4/ and are thenmore » reextracted with a l:l ammonia solution. The yield of tungsten isotopes is not less than 95%, and the content of radioactive impurities of other isotopes is not more than 0.1%.« less

A novel copper(II) coordination at His186 in full-length murine prion protein

DOE Office of Scientific and Technical Information (OSTI.GOV)

Watanabe, Yasuko; Hiraoka, Wakako; Igarashi, Manabu

2010-04-09

To explore Cu(II) ion coordination by His{sup 186} in the C-terminal domain of full-length prion protein (moPrP), we utilized the magnetic dipolar interaction between a paramagnetic metal, Cu(II) ion, and a spin probe introduced in the neighborhood of the postulated binding site by the spin labeling technique (SDSL technique). Six moPrP mutants, moPrP(D143C), moPrP(Y148C), moPrP(E151C), moPrP(Y156C), moPrP(T189C), and moPrP(Y156C,H186A), were reacted with a methane thiosulfonate spin probe and a nitroxide residue (R1) was created in the binding site of each one. Line broadening of the ESR spectra was induced in the presence of Cu(II) ions in moPrP(Y148R1), moPrP(Y151R1), moPrP(Y156R1), andmore » moPrP(T189R1) but not moPrP(D143R1). This line broadening indicated the presence of electron-electron dipolar interaction between Cu(II) and the nitroxide spin probe, suggesting that each interspin distance was within 20 A. The interspin distance ranges between Cu(II) and the spin probes of moPrP(Y148R1), moPrP(Y151R1), moPrP(Y156R1), and moPrP(T189R1) were estimated to be 12.1 A, 18.1 A, 10.7 A, and 8.4 A, respectively. In moPrP(Y156R1,H186A), line broadening between Cu(II) and the spin probe was not observed. These results suggest that a novel Cu(II) binding site is involved in His186 in the Helix2 region of the C-terminal domain of moPrP{sup C}.« less

New transitions and feeding of the Jπ=(8+) isomer in 186Re

NASA Astrophysics Data System (ADS)

Matters, D. A.; Fotiades, N.; Carroll, J. J.; Chiara, C. J.; McClory, J. W.; Kawano, T.; Nelson, R. O.; Devlin, M.

2015-11-01

The spallation neutron source at the Los Alamos Neutron Science Center Weapons Neutron Research facility was used to populate excited states in 186Re via (n ,2 n γ ) reactions on an enriched 187Re target. Gamma rays were detected with the GErmanium Array for Neutron Induced Excitations spectrometer, a Compton-suppressed array of 18 HPGe detectors. Incident neutron energies were determined by the time-of-flight technique and used to obtain γ -ray excitation functions for the purpose of identifying γ rays by reaction channel. Analysis of the singles γ -ray spectrum gated on the neutron energy range 10 ≤En≤25 MeV resulted in five transitions and one level added to the 186Re level scheme. The additions include the placement of three γ rays at 266.7, 381.2, and 647.7 keV which have been identified as feeding the 2.0 ×105yr , Jπ=(8+) isomer and yield an improved value of 148.2 (5 )keV for the isomer energy. These transitions may have astrophysical implications related to the use of the Re-Os cosmochronometer.

Metallorganic chemical vapor deposition and atomic layer deposition approaches for the growth of hafnium-based thin films from dialkylamide precursors for advanced CMOS gate stack applications

NASA Astrophysics Data System (ADS)

Consiglio, Steven P.

To continue the rapid progress of the semiconductor industry as described by Moore's Law, the feasibility of new material systems for front end of the line (FEOL) process technologies needs to be investigated, since the currently employed polysilicon/SiO2-based transistor system is reaching its fundamental scaling limits. Revolutionary breakthroughs in complementary-metal-oxide-semiconductor (CMOS) technology were recently announced by Intel Corporation and International Business Machines Corporation (IBM), with both organizations revealing significant progress in the implementation of hafnium-based high-k dielectrics along with metal gates. This announcement was heralded by Gordon Moore as "...the biggest change in transistor technology since the introduction of polysilicon gate MOS transistors in the late 1960s." Accordingly, the study described herein focuses on the growth of Hf-based dielectrics and Hf-based metal gates using chemical vapor-based deposition methods, specifically metallorganic chemical vapor deposition (MOCVD) and atomic layer deposition (ALD). A family of Hf source complexes that has received much attention recently due to their desirable properties for implementation in wafer scale manufacturing is the Hf dialkylamide precursors. These precursors are room temperature liquids and possess sufficient volatility and desirable decomposition characteristics for both MOCVD and ALD processing. Another benefit of using these sources is the existence of chemically compatible Si dialkylamide sources as co-precursors for use in Hf silicate growth. The first part of this study investigates properties of MOCVD-deposited HfO2 and HfSixOy using dimethylamido Hf and Si precursor sources using a customized MOCVD reactor. The second part of this study involves a study of wet and dry surface pre-treatments for ALD growth of HfO2 using tetrakis(ethylmethylamido)hafnium in a wafer scale manufacturing environment. The third part of this study is an investigation of

Conduction Channel Formation and Dissolution Due to Oxygen Thermophoresis/Diffusion in Hafnium Oxide Memristors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Suhas; Wang, Ziwen; Huang, Xiaopeng

Due to the favorable operating power, endurance, speed, and density., transition-metal-oxide memristors, or resistive random-access memory (RRAM) switches, are under intense development for storage-class memory. Their commercial deployment critically depends on predictive compact models based on understanding nanoscale physiocochemical forces, which remains elusive and controversial owing to the difficulties in directly observing atomic motions during resistive switching, Here, using scanning transmission synchrotron X-ray spectromicroscopy to study in situ switching of hafnium oxide memristors, we directly observed the formation of a localized oxygen-deficiency-derived conductive channel surrounded by a low-conductivity ring of excess oxygen. Subsequent thermal annealing homogenized the segregated oxygen, resettingmore » the cells toward their as-grown resistance state. We show that the formation and dissolution of the conduction channel are successfully modeled by radial thermophoresis and Fick diffusion of oxygen atoms driven by Joule heating. This confirmation and quantification of two opposing nanoscale radial forces that affect bipolar memristor switching are important components for any future physics-based compact model for the electronic switching of these devices.« less

Highly effective electronic passivation of silicon surfaces by atomic layer deposited hafnium oxide

NASA Astrophysics Data System (ADS)

Cui, Jie; Wan, Yimao; Cui, Yanfeng; Chen, Yifeng; Verlinden, Pierre; Cuevas, Andres

2017-01-01

This paper investigates the application of hafnium oxide (HfO2) thin films to crystalline silicon (c-Si) solar cells. Excellent passivation of both n- and p-type crystalline silicon surfaces has been achieved by the application of thin HfO2 films prepared by atomic layer deposition. Effective surface recombination velocities as low as 3.3 and 9.9 cm s-1 have been recorded with 15 nm thick films on n- and p-type 1 Ω cm c-Si, respectively. The surface passivation by HfO2 is activated at 350 °C by a forming gas anneal. Capacitance voltage measurement shows an interface state density of 3.6 × 1010 cm-2 eV-1 and a positive charge density of 5 × 1011 cm-2 on annealed p-type 1 Ω cm c-Si. X-ray diffraction unveils a positive correlation between surface recombination and crystallinity of the HfO2 and a dependence of the crystallinity on both annealing temperature and film thickness. In summary, HfO2 is demonstrated to be an excellent candidate for surface passivation of crystalline silicon solar cells.

A COMPARISON OF EXPERIMENTS AND THREE-DIMENSIONAL ANALYSIS TECHNIQUES. PART I. UNPOISONED UNIFORM SLAB CORE WITH A PARTIALLY INSERTED HAFNIUM ROD

DOE Office of Scientific and Technical Information (OSTI.GOV)

Renzi, N.E.; Roseberry, R.J.

>The experimental measurements and nuclear analysis of a uniformly loaded, unpoisoned slab core with a partially insented hafnium rod are described. Comparisons of experimental data with calculated results of the UFO code and flux synthesis techniques are given. It was concluded that one of the flux synthesis techniques and the UFO code are able to predict flux distributions to within approximately 5% of experiment for most cases. An error of approximately 10% was found in the synthesis technique for a channel near the partially inserted rod. The various calculations were able to predict neutron pulsed shutdowns to only approximately 30%.more » (auth)« less

High-energy X-ray detection by hafnium-doped organic-inorganic hybrid scintillators prepared by sol-gel method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sun, Yan; Koshimizu, Masanori, E-mail: koshi@qpc.che.tohoku.ac.jp; Yahaba, Natsuna

2014-04-28

With the aim of enhancing the efficiency with which plastic scintillators detect high-energy X-rays, hafnium-doped organic-inorganic hybrid scintillators were fabricated via a sol-gel method. Transmission electron microscopy of sampled material reveals the presence of Hf{sub x}Si{sub 1−x}O{sub 2} nanoparticles, dispersed in a polymer matrix that constitutes the active material of the X-ray detector. With Hf{sub x}Si{sub 1−x}O{sub 2} nanoparticles incorporated in the polymer matrix, the absorption edge and the luminescence wavelength is shifted, which we attribute to Mie scattering. The detection efficiency for 67.4-keV X-rays in a 0.6-mm-thick piece of this material is two times better than the same thicknessmore » of a commercial plastic scintillator-NE142.« less

Kepler-186f, the First Earth-size Planet in the Habitable Zone Artist Concept

NASA Image and Video Library

2014-04-17

This artist concept depicts Kepler-186f, the first validated Earth-size planet to orbit a distant star in the habitable zone, a range of distance from a star where liquid water might pool on the planet surface.

A DPYD variant (Y186C) in individuals of African ancestry associated with reduced DPD enzyme activity

PubMed Central

Offer, Steven M.; Lee, Adam M.; Mattison, Lori K.; Fossum, Croix; Wegner, Natalie J.; Diasio, Robert B.

2013-01-01

5-fluorouracil (5-FU) is used to treat many aggressive cancers, such as those of the colon, breast, and head & neck. The responses to 5-FU, both toxicity and efficacy, vary between racial groups, potentially due to variability in enzyme activity of dihydropyrimidine dehydrogenase (DPD, encoded by DPYD). In the present study, the genetic associations between DPYD variations and circulating mononuclear cell DPD enzyme activity were evaluated in 94 African American and 81 European American volunteers. The DPYD-Y186C variant was unique to individuals of African ancestry, and DPD activity was 46% reduced in carriers compared to non-carriers (279±35 compared to 514±168 pmol 5-FU min−1 mg−1; P=0.00029). 26% of the African Americans with reduced DPD activity in this study carried Y186C. In the African American cohort, following exclusion of Y186C carriers, homozygous carriers of C29R showed 27% higher DPD activity compared to non-carriers (609±152 and 480±152 pmol 5-FU min−1 mg−1, respectively; P=0.013). PMID:23588312

Obliquity Variations of Habitable Zone Planets Kepler-62f and Kepler-186f

NASA Astrophysics Data System (ADS)

Shan, Yutong; Li, Gongjie

2018-06-01

Obliquity variability could play an important role in the climate and habitability of a planet. Orbital modulations caused by planetary companions and the planet’s spin axis precession due to the torque from the host star may lead to resonant interactions and cause large-amplitude obliquity variability. Here we consider the spin axis dynamics of Kepler-62f and Kepler-186f, both of which reside in the habitable zone around their host stars. Using N-body simulations and secular numerical integrations, we describe their obliquity evolution for particular realizations of the planetary systems. We then use a generalized analytic framework to characterize regions in parameter space where the obliquity is variable with large amplitude. We find that the locations of variability are fine-tuned over the planetary properties and system architecture in the lower-obliquity regimes (≲40°). As an example, assuming a rotation period of 24 hr, the obliquities of both Kepler-62f and Kepler-186f are stable below ∼40°, whereas the high-obliquity regions (60°–90°) allow moderate variabilities. However, for some other rotation periods of Kepler-62f or Kepler-186f, the lower-obliquity regions could become more variable owing to resonant interactions. Even small deviations from coplanarity (e.g., mutual inclinations ∼3°) could stir peak-to-peak obliquity variations up to ∼20°. Undetected planetary companions and/or the existence of a satellite could also destabilize the low-obliquity regions. In all cases, the high-obliquity region allows for moderate variations, and all obliquities corresponding to retrograde motion (i.e., >90°) are stable.

Chemical Abundances of M-Dwarfs from the Apogee Survey. I. The Exoplanet Hosting Stars Kepler-138 and Kepler-186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Souto, D.; Cunha, K.; García-Hernández, D. A.

2017-02-01

We report the first detailed chemical abundance analysis of the exoplanet-hosting M-dwarf stars Kepler-138 and Kepler-186 from the analysis of high-resolution ( R ∼ 22,500) H -band spectra from the SDSS-IV–APOGEE survey. Chemical abundances of 13 elements—C, O, Na, Mg, Al, Si, K, Ca, Ti, V, Cr, Mn, and Fe—are extracted from the APOGEE spectra of these early M-dwarfs via spectrum syntheses computed with an improved line list that takes into account H{sub 2}O and FeH lines. This paper demonstrates that APOGEE spectra can be analyzed to determine detailed chemical compositions of M-dwarfs. Both exoplanet-hosting M-dwarfs display modest sub-solar metallicities:more » [Fe/H]{sub Kepler-138} = −0.09 ± 0.09 dex and [Fe/H]{sub Kepler-186} = −0.08 ± 0.10 dex. The measured metallicities resulting from this high-resolution analysis are found to be higher by ∼0.1–0.2 dex than previous estimates from lower-resolution spectra. The C/O ratios obtained for the two planet-hosting stars are near-solar, with values of 0.55±0.10 for Kepler-138 and 0.52±0.12 for Kepler-186. Kepler-186 exhibits a marginally enhanced [Si/Fe] ratio.« less

Measurement and Simulation of Thermal Conductivity of Hafnium-Aluminum Thermal Neutron Absorber Material

DOE PAGES

Guillen, Donna Post; Harris, William H.

2016-05-11

A metal matrix composite (MMC) material comprised of hafnium aluminide (Al3Hf) intermetallic particles in an aluminum matrix has been identified as a promising material for fast-flux irradiation testing applications. This material can filter thermal neutrons while simultaneously providing high rates of conductive cooling for experiment capsules. Our purpose is to investigate effects of Hf-Al material composition and neutron irradiation on thermophysical properties, which were measured before and after irradiation. When performing differential scanning calorimetry (DSC) on the irradiated specimens, a large exotherm corresponding to material annealment was observed. Thus, a test procedure was developed to perform DSC and laser flashmore » analysis (LFA) to obtain the specific heat and thermal diffusivity of pre- and post-annealment specimens. This paper presents the thermal properties for three states of the MMC material: (1) unirradiated, (2) as-irradiated, and (3) irradiated and annealed. Microstructure-property relationships were obtained for the thermal conductivity. These relationships are useful for designing components from this material to operate in irradiation environments. Furthermore, the ability of this material to effectively conduct heat as a function of temperature, volume fraction Al 3Hf, radiation damage and annealing is assessed using the MOOSE suite of computational tools.« less

Ferroelectric transistors with monolayer molybdenum disulfide and ultra-thin aluminum-doped hafnium oxide

NASA Astrophysics Data System (ADS)

Yap, Wui Chung; Jiang, Hao; Liu, Jialun; Xia, Qiangfei; Zhu, Wenjuan

2017-07-01

In this letter, we demonstrate ferroelectric memory devices with monolayer molybdenum disulfide (MoS2) as the channel material and aluminum (Al)-doped hafnium oxide (HfO2) as the ferroelectric gate dielectric. Metal-ferroelectric-metal capacitors with 16 nm thick Al-doped HfO2 are fabricated, and a remnant polarization of 3 μC/cm2 under a program/erase voltage of 5 V is observed. The capability of potential 10 years data retention was estimated using extrapolation of the experimental data. Ferroelectric transistors based on embedded ferroelectric HfO2 and MoS2 grown by chemical vapor deposition are fabricated. Clockwise hysteresis is observed at low program/erase voltages due to slow bulk traps located near the 2D/dielectric interface, while counterclockwise hysteresis is observed at high program/erase voltages due to ferroelectric polarization. In addition, the endurances of the devices are tested, and the effects associated with ferroelectric materials, such as the wake-up effect and polarization fatigue, are observed. Reliable writing/reading in MoS2/Al-doped HfO2 ferroelectric transistors over 2 × 104 cycles is achieved. This research can potentially lead to advances of two-dimensional (2D) materials in low-power logic and memory applications.

AC-186, a Selective Nonsteroidal Estrogen Receptor β Agonist, Shows Gender Specific Neuroprotection in a Parkinson’s Disease Rat Model

PubMed Central

2013-01-01

Drugs that selectively activate estrogen receptor β (ERβ) are potentially safer than the nonselective estrogens currently used in hormonal replacement treatments that activate both ERβ and ERα. The selective ERβ agonist AC-186 was evaluated in a rat model of Parkinson’s disease induced through bilateral 6-hydroxydopamine lesions of the substantia nigra. In this model, AC-186 prevented motor, cognitive, and sensorimotor gating deficits and mitigated the loss of dopamine neurons in the substantia nigra, in males, but not in females. Furthermore, in male rats, 17β-estradiol, which activates ERβ and ERα with equal potency, did not show the same neuroprotective benefits as AC-186. Hence, in addition to a beneficial safety profile for use in both males and females, a selective ERβ agonist has a differentiated pharmacological profile compared to 17β-estradiol in males. PMID:23898966

POX 186: A Dwarf Galaxy in the Process of Formation?

NASA Astrophysics Data System (ADS)

Corbin, Michael R.; Vacca, William D.

2002-12-01

We present deep U-, V-, and I-band images of the ``ultracompact'' blue dwarf galaxy POX 186 obtained with the Planetary Camera 2 of the Hubble Space Telescope. We have also obtained a near-ultraviolet spectrum of the object with the Space Telescope Imaging Spectrograph and combine this with a new ground-based optical spectrum. The images confirm the galaxy to be extremely small, with a maximum extent of only 300 pc, a luminosity of ~10-4L*, and an estimated mass of ~107 Msolar. Its morphology is highly asymmetric, with a tail of material on its western side that may be tidal in origin. The U-band image shows this tail to be part of a stream of material in which stars have recently formed. Most of the star formation in the galaxy is, however, concentrated in a central, compact (d~10-15 pc) star cluster. We estimate this cluster to have a total mass of ~105 Msolar, to be forming stars at a rate of less than 0.05 yr-1, and to have a maximum age of a few million years. The outer regions of the galaxy are significantly redder than the cluster, with V-I colors consistent with a population dominated by K and M stars. From our analysis of the optical spectrum we find the galaxy to have a metallicity Z~=0.06 Zsolar and to contain a significant amount of internal dust [E(B-V)~=0.28] both values agree with previous estimates. While these results rule out earlier speculation that POX 186 is a protogalaxy, its morphology, mass, and active star formation suggest that it represents a recent (within ~108 yr) collision between two clumps of stars of subgalactic size (~100 pc). POX 186 may thus be a very small dwarf galaxy that, dynamically speaking, is still in the process of formation. This interpretation is supported by the fact that it resides in a void, so its morphology cannot be explained as the result of an encounter with a more massive galaxy. Clumps of stars this small may represent the building blocks required by hierarchical models of galaxy formation, and these results

Radiosynovectomy in haemophilic synovitis of elbows and ankles: Is the effectiveness of yttrium-90 and rhenium-186 different?

PubMed

Rodriguez-Merchan, E C; De La Corte-Rodriguez, H

2016-04-01

Radiosynovectomy (RS) reduces the number of haemarthroses and the synovial size in chronic haemophilic synovitis. The purpose of this study was to quantitatively compare the effectiveness of two types of RS (yttrium-90 vs. rhenium-186) in terms of the objective improvement of haemarthroses and synovial size. Seventy RSs were performed in 70 joints (44 elbows, 26 ankles) of 70 haemophiliacs diagnosed with chronic synovitis. Yttrium-90 was used in 21 joints and rhenium-186 was used in 49 joints. The mean patient age was 20.61 years. RS resulted in significant improvement in the three variables studied (six months before RS vs. six months after RS), namely in the number of episodes of haemarthrosis (67.8% improvement); the size of the synovium as measured by means of a clinical scale (43.8% improvement) and imaging techniques in millimetres (26.7% improvement). We did not find significant statistical differences between yttrium-90 and rhenium-186 regarding their efficacy. No correlation was found between the results and other variables: age, joint (ankle or elbow), presence or absence of radiological involvement, type of haemophilia (A or B), grade of haemophilia (mild, moderate or severe), previous haematological treatment (on demand or prophylaxis), and the presence or absence of inhibitor Yttrium-90 RS and rhenium-186 RS were equally effective in reducing the number of haemarthroses and the size of the synovium in ankles and elbows in the short-term (6 months). No correlation was found between the results and other patients' characteristics. Copyright © 2016 Elsevier Ltd. All rights reserved.

The origin of 2.7 eV luminescence and 5.2 eV excitation band in hafnium oxide

DOE Office of Scientific and Technical Information (OSTI.GOV)

Perevalov, T. V., E-mail: timson@isp.nsc.ru; Novosibirsk State University, 2 Pirogova St., 630090 Novosibirsk; Aliev, V. Sh.

2014-02-17

The origin of a blue luminescence band at 2.7 eV and a luminescence excitation band at 5.2 eV of hafnia has been studied in stoichiometric and non-stoichiometric hafnium oxide films. Experimental and calculated results from the first principles valence band spectra showed that the stoichiometry violation leads to the formation of the peak density of states in the band gap caused by oxygen vacancies. Cathodoluminescence in the non-stoichiometric film exhibits a band at 2.65 eV that is excited at the energy of 5.2 eV. The optical absorption spectrum calculated for the cubic phase of HfO{sub 2} with oxygen vacancies showsmore » a peak at 5.3 eV. Thus, it could be concluded that the blue luminescence band at 2.7 eV and HfO{sub x} excitation peak at 5.2 eV are due to oxygen vacancies. The thermal trap energy in hafnia was estimated.« less

IER-297 CED-2: Final Design for Thermal/Epithermal eXperiments with Jemima Plates with Polyethylene and Hafnium

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nelson, A. J.; Percher, C. M.; Zywiec, W. J.

This report presents the final design (CED-2) for IER-297, and focuses on 15 critical configurations using highly enriched uranium (HEU) Jemima plates moderated by polyethylene with and without hafnium diluent. The goal of the U.S. Nuclear Criticality Safety Program’s Thermal/Epithermal eXperiments (TEX) is to design and conduct new critical experiments to address high priority nuclear data needs from the nuclear criticality safety and nuclear data communities, with special emphasis on intermediate energy (0.625 eV – 100 keV) assemblies that can be easily modified to include various high priority diluent materials. The TEX (IER 184) CED-1 Report [1], completed in 2012,more » demonstrated the feasibility of meeting the TEX goals with two existing NCSP fissile assets, plutonium Zero Power Physics Reactor (ZPPR) plates and highly enriched uranium (HEU) Jemima plates. The first set of TEX experiments will focus on using the plutonium ZPPR plates with polyethylene moderator and tantalum diluents.« less

In-beam γ -ray spectroscopy studies of medium-spin states in the odd-odd nucleus 186Re

NASA Astrophysics Data System (ADS)

Matters, D. A.; Kondev, F. G.; Aoi, N.; Ayyad, Y.; Byrne, A. P.; Carpenter, M. P.; Carroll, J. J.; Chiara, C. J.; Davidson, P. M.; Dracoulis, G. D.; Fang, Y. D.; Hoffman, C. R.; Hughes, R. O.; Ideguchi, E.; Janssens, R. V. F.; Kanaya, S.; Kay, B. P.; Kibédi, T.; Lane, G. J.; Lauritsen, T.; McClory, J. W.; Nieminen, P.; Noji, S.; Odahara, A.; Ong, H. J.; Stuchbery, A. E.; Tran, D. T.; Watanabe, H.; Wilson, A. N.; Yamamoto, Y.; Zhu, S.

2017-07-01

Excited states in 186Re with spins up to J =12 ℏ were investigated in two separate experiments using 186W(d ,2 n ) reactions at beam energies of 12.5 and 14.5 MeV. Two- and threefold γ -ray coincidence data were collected using the CAESAR and CAGRA spectrometers, respectively, each composed of Compton-suppressed high-purity germanium detectors. Analysis of the data revealed rotational bands built on several two-quasiparticle intrinsic states, including a long-lived Kπ=(8+) isomer. Configuration assignments were supported by an analysis of in-band properties, such as |gK-gR| values. The excitation energies of the observed intrinsic states were compared with results from multi-quasiparticle blocking calculations, based on the Lipkin-Nogami pairing approach, that included contributions from the residual proton-neutron interactions.

78 FR 69929 - Fifty-Ninth Meeting: RTCA Special Committee 186, Automatic Dependent Surveillance-Broadcast (ADS-B)

Federal Register 2010, 2011, 2012, 2013, 2014

2013-11-21

.... December 13 Chairman's Introductory Remarks Working Group Reports Review of Meeting Agenda Review/Approval... Services (SBS) Program--Status. EUROCAE WG-51 Report Review/Approval--New Document--Safety, Performance and.../SC186-326. Review/Approval--Revised DO-317A--Minimum Operational Performance Standards (MOPS) for...

Photoluminescence properties of Eu3+ doped HfO2 coatings formed by plasma electrolytic oxidation of hafnium

NASA Astrophysics Data System (ADS)

Stojadinović, Stevan; Tadić, Nenad; Ćirić, Aleksandar; Vasilić, Rastko

2018-03-01

Plasma electrolytic oxidation was used for synthesis of Eu3+ doped monoclinic HfO2 coatings on hafnium substrate. Results of photoluminescence (PL) measurements show the existence of two distinct regions: one that is related to the blue emission originating from oxygen vacancy defects in HfO2 and the other one characterized with a series of sharp orange-red emission peaks related to f-f transitions of Eu3+ from excited level 5D0 to lower levels 7FJ (J = 0, 1, 2, 3, and 4). PL peaks appearing in excitation spectra of obtained coatings are attributed either to charge transfer state of Eu3+ or to direct excitation of the Eu3+ ground state 7F0 into higher levels of the 4f-manifold. PL of formed coatings increases with PEO time due to an increase of oxygen vacancy defects and the content of Eu3+. Acquired experimental data suggest that hypersensitive electrical dipole transition is much more intense than the magnetic dipole transition, indicating that Eu3+ ions occupy a non-inversion symmetry sites.

In-beam γ -ray spectroscopy studies of medium-spin states in the odd-odd nucleus Re 186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Matters, D. A.; Kondev, F. G.; Aoi, N.

2017-07-01

Excited states in 186Re with spins up to J = 12~ were investigated in two separate experiments using 186W(d, 2n) reactions at beam energies of 12.5 MeV and 14.5 MeV. Two- and three-fold γ-ray coincidence data were collected using the CAESAR and CAGRA spectrometers, respectively, each composed of Compton-suppressed HpGe detectors. Analysis of the data revealed rotational bands built on several two-quasiparticle intrinsic states, including a long-lived Kπ = (8+) isomer. Configuration assignments were supported by an analysis of in-band properties, such as |gK - gR| values. The excitation energies of the observed intrinsic states were compared with results frommore » multiquasiparticle blocking calculations, based on the Lipkin-Nogami pairing approach, that included contributions from the residual proton-neutron interactions.« less

Associated factors of radiation pneumonitis induced by precise radiotherapy in 186 elderly patients with esophageal cancer.

PubMed

Cui, Zhen; Tian, Ye; He, Bin; Li, Hongwei; Li, Duojie; Liu, Jingjing; Cai, Hanfei; Lou, Jianjun; Jiang, Hao; Shen, Xueming; Peng, Kaigui

2015-01-01

Radiation pneumonitis is one of the most severe complications of esophageal cancer. To explore the factors correlated to radiation pneumonitis induced by precise radiotherapy for elderly patients with esophageal cancer. The retrospective analysis was used to collect clinical data from 186 elderly patients with esophageal cancer. The incidence of radiation pneumonitis was observed, followed by statistical analysis through ANVON or multiple regression analysis. 27 in 186 cases of esophageal cancer suffered from radiation pneumonitis, with incidence of 14.52%. The single factor analysis showed that, Karnofsky performance status (KPS) score, chronic obstructive pulmonary disease, concurrent chemoradiotherapy, gross tumor volume (GTV) dose, lung V20, mean lung dose (MLD) and planning target volume (PTV) were associated with radiation pneumonitis. The logistic regression analysis indicated that, concurrent chemoradiotherapy, GTV dose, lung V20 and PTV were the independent factors of radiation pneumonitis. The concurrent chemoradiotherapy, GTV dose, lung V20, MLD and PTV are the major risk factors of radiation pneumonitis for elderly patients with esophageal cancer.

Thermomechanical and Thermochemical Behavior of a Hafnium-20 Percent Tantalum Alloy. Ph.D. Thesis - North Carolina State Univ., Raleigh

NASA Technical Reports Server (NTRS)

Howell, J. P.

1971-01-01

An investigation was conducted to determine the thermomechanical and thermochemical behavior of a high temperature, oxidation resistant, hafnium-20 percent tantalum alloy. The elastic and shear moduli of this alloy were determined in air up to 1000 C and in vacuum up to 2000 C using a mechanical resonance technique. The internal friction of the alloy was measured up to temperatures greater than 1400 C. Room temperature stress-strain behavior of the oxidized and unoxidized alloy was established. The effect of annealing on the elastic and shear moduli of the extruded rod material was investigated. The martensitic-type phase transformation occurring in the alloy was studied using hot stage metallography and electron microscopy. Static oxidation tests were conducted on the alloy at temperatures from 1000 C to 1700 C with weight gain measurements made as a function of time and temperatures. Surface morphology studies were conducted on the oxide coatings formed at the different temperatures using scanning electron microscopy and X-ray diffraction techniques.

Response surface optimization of electro-oxidation process for the treatment of C.I. Reactive Yellow 186 dye: reaction pathways

NASA Astrophysics Data System (ADS)

Rajkumar, K.; Muthukumar, M.

2017-05-01

In this study, central composite design at five levels (- β, -1, 0, +1, + β) combined with response surface methodology has been applied to optimize C.I. Reactive Yellow 186 using electro-oxidation process with graphite electrodes in a batch reactor. The variables considered were the pH ( X 1), NaCl concentration (M) ( X 2), and electrolysis time (min) ( X 3) on C.I. Reactive Yellow 186 were studied. A second-order empirical relationship between the response and independent variables was derived. Analysis of variance showed a high coefficient of determination value ( R 2 = 0.9556 and 0.9416 for color and COD, respectively). The optimized condition of the electro-oxidation of Reactive Yellow 186 is as follows: pH 3.9; NaCl concentration 0.11 M; and electrolysis time 18 min. Under this condition, the maximal decolorization efficiency of 99 % and COD removal 73 % was achieved. Detailed physico-chemical analysis of electrode and residues of the electro-oxidation process has also been carried out UV-Visible and Fourier transform infrared spectroscopy. The intermediate compounds formed during the oxidation were identified using a gas chromatography coupled with mass spectrometry. According to these results, response surface methodology could be useful for reducing the time to treat effluent wastewater.

Compensation for matrix effects in the gas chromatography-mass spectrometry analysis of 186 pesticides in tea matrices using analyte protectants.

PubMed

Li, Yan; Chen, Xi; Fan, Chunlin; Pang, Guofang

2012-11-30

A gas chromatography-mass spectrometry (GC-MS) analytical method was developed for simultaneously determining 186 pesticides in tea matrices using analyte protectants to counteract the matrix-induced effect. The matrix effects were evaluated for green, oolong and black tea, representing unfermented, partially fermented and completely fermented teas respectively and depending on the type of tea, 72%, 94% and 94% of the pesticides presented strong response enhancement effect. Several analyte protectants as well as certain combinations of these protectants were evaluated to check their compensation effects. A mixture of triglycerol and d-ribonic acid-γ-lactone (both at 2mg/mL in the injected samples) was found to be the most effective in improving the chromatographic behavior of the 186 pesticides. More than 96% of the 186 pesticides achieved recoveries within the range of 70-120% when using the selected mixture of analyte protectants. The simple addition of analyte protectants offers a more convenient solution to overcome matrix effects, results in less active sites compared to matrix-matched standardization and can be an effective approach to compensate for matrix effects in the GC-MS analysis of pesticide residues. Copyright © 2012 Elsevier B.V. All rights reserved.

Structure of the Kπ=4+ bands in Os186,188

NASA Astrophysics Data System (ADS)

Phillips, A. A.; Garrett, P. E.; Lo Iudice, N.; Sushkov, A. V.; Bettermann, L.; Braun, N.; Burke, D. G.; Demand, G. A.; Faestermann, T.; Finlay, P.; Green, K. L.; Hertenberger, R.; Leach, K. G.; Krücken, R.; Schumaker, M. A.; Svensson, C. E.; Wirth, H.-F.; Wong, J.

2010-09-01

The (He3,d) single-proton stripping reaction has been performed on targets of Re185,187 to investigate the structures of the 43+ states in Os186,188. The experiment employed 30 MeV He3 beams, and the reaction products were analyzed with a Q3D spectrograph. Absolute cross sections were determined at nine angles between 5° and 50° for states up to approximately 3 MeV in excitation energy. Large (5)/(2)+[402]π+(3)/(2)+[402]π two-quasiparticle components are deduced for the 43+ levels of both isotopes. Their magnitudes are in agreement with calculations performed using the quasiparticle phonon model, which predicts a coexistence of a large hexadecapole with a smaller, but sizable, γ-γ component in the 43+.

The 190Pt-186Os Decay System Applied to Dating Platinum-Group Element Mineralization in Layered Intrusions, Ophiolites and Detrital Deposits

NASA Astrophysics Data System (ADS)

Coggon, J. A.; Nowell, G.; Pearson, G.; Oberthür, T.; Lorand, J.; Melcher, F.; Parman, S. W.

2010-12-01

Discrete platinum-group minerals (PGM) occur as accessory phases in mafic-ultamafic intrusions and ophiolitic chromitites, as well as numerous detrital deposits globally. The 190Pt-186Os decay system, measured by laser ablation MC-ICPMS (LA-MC-ICPMS) provides a useful geochronometric tool for direct dating of PGM. Here we present two examples that verify the accuracy of the technique in geologically well constrained situations and demonstrate the potential for using the 190Pt-186Os PGM method to accurately date layered mafic intrusions, ophiolitic chromitites and detrital PGM deposits. Fifty PGM grains from three different horizons within the Bushveld complex yield a Pt-Os isochron age of 2012 ± 47 Ma (2σ, MSWD = 1.19, 186Os/188Osi = 0.119818 ± 0.000006). This is consistent with the published U-Pb zircon age of 2054 Ma (Scoates and Friedman, 2008). The younger PGM isochron age is not likely to be a function of difference in blocking temperatures in the different systems. Pt-Os model ages are possible in high pt grains because initial 186Os/188Os can be well constrained. Using this approach we obtained Pt-Os model ages of 2113 ± 106 Ma and 2042 ± 102 Ma for a Bushveld Pt-Fe alloy and sperrylite respectively. Detrital PGM derived from the Meratus ophiolite, southeast Borneo yield a 190Pt-186Os isochron age of 202.5 Ma ± 8.3 Ma (2σ, n = 260, MSWD = 0.90, 186Os/188Osi = 0.119830 ± 0.000003), consistent with radiometric and biostratigraphic age constraints (Wakita et al., 1998). We interpret this as the age of formation of the PGM grains in during chromitite genesis in the lower oceanic lithosphere. Our combined data demonstrate the utility of the LA-MC-ICPMS method as a tool for accurate Pt-Os dating of detrital PGM as well as their igneous parent bodies. We can constrain Pt/Os fractionation at the ablation site as being < 2.5%, while within-grain heterogeneity is ultimately one of the strongest controls on isochron and single-grain ages given the partial

Efficient UV-emitting X-ray phosphors: octahedral Zr(PO 4) 6 luminescence centers in potassium hafnium-zirconium phosphates K 2Hf 1- xZr x(PO 4) 2 and KHf 2(1- x) Zr 2 x(PO 4) 3

NASA Astrophysics Data System (ADS)

Torardi, C. C.; Miao, C. R.; Li, J.

2003-02-01

Potassium hafnium-zirconium phosphates, K 2Hf 1- xZr x(PO 4) 2 and KHf 2(1- x) Zr 2 x(PO 4) 3, are broad-band UV-emitting phosphors. At room temperature, they have emission peak maxima at approximately 322 and 305 nm, respectively, under 30 kV peak molybdenum X-ray excitation. Both phosphors demonstrate luminescence efficiencies that make them up to ˜60% as bright as commercially available CaWO 4 Hi-Plus. The solid-state and flux synthesis conditions, and X-ray excited UV luminescence of these two phosphors are discussed. Even though the two compounds have different atomic structures, they contain zirconium in the same active luminescence environment as that found in highly efficient UV-emitting BaHf 1- xZr x(PO 4) 2. All the three materials have hafnium and zirconium in octahedral coordination via oxygen-atom corner sharing with six separate PO 4 tetrahedra. This octahedral Zr(PO 4) 6 moiety appears to be an important structural element for efficient X-ray excited luminescence, as are the edge-sharing octahedral TaO 6 chains for tantalate emission.

Long non-coding RNA PVT1 serves as a competing endogenous RNA for miR-186-5p to promote the tumorigenesis and metastasis of hepatocellular carcinoma.

PubMed

Lan, Tian; Yan, Xia; Li, Zhuo; Xu, Xin; Mao, Qi; Ma, Weijie; Hong, Zhenfei; Chen, Xi; Yuan, Yufeng

2017-06-01

Hepatocellular carcinoma is third leading cause of cancer-related death globally. Long non-coding RNA plasmacytoma variant translocation 1 has been reported to be dysregulated and plays a crucial role in various cancers. In this study, we investigated the interactions between plasmacytoma variant translocation 1 and miR-186-5p in the progression of hepatocellular carcinoma and explored the functional significance of plasmacytoma variant translocation 1. It was determined that plasmacytoma variant translocation 1 was significantly higher, while miR-186-5p was statistically lower in the hepatocellular carcinoma tissues than that in the adjacent normal tissues. Using gain-of-function and loss-of-function methods, our results revealed that plasmacytoma variant translocation 1 affected hepatocellular carcinoma cells proliferation, invasion, and migration. It was found that there was direct interaction between miR-186-5p and the binding site of plasmacytoma variant translocation 1 by performing dual-luciferase assay and RNA immunoprecipitation assay. Furthermore, it was identified that plasmacytoma variant translocation 1 regulated the expression of the miR-186-5p target gene, yes-associated protein 1. Taken together, plasmacytoma variant translocation 1 served as an endogenous sponge for miR-186-5p to reduce its inhibiting effect on yes-associated protein 1 and thus promoted the tumorigenesis of hepatocellular carcinoma.

Circular RNA hsa_circ_0010729 regulates vascular endothelial cell proliferation and apoptosis by targeting the miR-186/HIF-1α axis.

PubMed

Dang, Rui-Ying; Liu, Feng-Li; Li, Yan

2017-08-19

Circular RNAs (circRNAs) are a group of non-protein-coding RNAs generated from back splicing. Emerging evidence has demonstrated its vital regulation on angiogenesis. However, the underlying mechanism responsible for circRNAs effects on vascular endothelial cells is still unclear. In the present study, we screened the expression profiles and investigated the physiological role of circRNAs in hypoxia-induced human umbilical vein endothelial cells (HUVECs). Using circRNA microarray analysis, we identified 36 circRNAs that were significantly dysregulated including 14 down-regulated circRNAs and 22 up-regulated with 2-fold change (P < 0.05). From the over-expressed circRNAs, hsa_circ_0010729 was selected as candidate circRNA and which was validated to be significantly up-regulated using RT-PCR. In loss-of-function experiments of HUVECs, hsa_circ_0010729 knockdown suppressed the proliferation and migration ability and enhanced apoptosis. Bioinformatic prediction and luciferase assay revealed that hsa_circ_0010729 and hypoxia inducible factor 1 alpha (HIF-1α) were targeted by miR-186. Validation experiments verified that hsa_circ_0010729 was co-expressed with HIF-1α, being negatively correlated with miR-186. Moreover, rescue experiments demonstrated that miR-186 inhibitor could reverse the role of hsa_circ_0010729 knockdown on HUVECs progression. Overall, the present study identifies the crucial regulation of hsa_circ_0010729 on vascular endothelial cell proliferation and apoptosis via targeting miR-186/HIF-1α axis. Copyright © 2017 Elsevier Inc. All rights reserved.

Facing-target mid-frequency magnetron reactive sputtered hafnium oxide film: Morphology and electrical properties

NASA Astrophysics Data System (ADS)

Zhang, Yu; Xu, Jun; Wang, You-Nian; Choi, Chi Kyu; Zhou, Da-Yu

2016-03-01

Amorphous hafnium dioxide (HfO2) film was prepared on Si (100) by facing-target mid-frequency reactive magnetron sputtering under different oxygen/argon gas ratio at room temperature with high purity Hf target. 3D surface profiler results showed that the deposition rates of HfO2 thin film under different O2/Ar gas ratio remain unchanged, indicating that the facing target midfrequency magnetron sputtering system provides effective approach to eliminate target poisoning phenomenon which is generally occurred in reactive sputtering procedure. X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) demonstrated that the gradual reduction of oxygen vacancy concentration and the densification of deposited film structure with the increase of oxygen/argon (O2/Ar) gas flow ratio. Atomic force microscopy (AFM) analysis suggested that the surface of the as-deposited HfO2 thin film tends to be smoother, the root-meansquare roughness (RMS) reduced from 0.876 nm to 0.333 nm while O2/Ar gas flow ratio increased from 1/4 to 1/1. Current-Voltage measurements of MOS capacitor based on Au/HfO2/Si structure indicated that the leakage current density of HfO2 thin films decreased by increasing of oxygen partial pressure, which resulted in the variations of pore size and oxygen vacancy concentration in deposited thin films. Based on the above characterization results the leakage current mechanism for all samples was discussed systematically.

Discovery and Classification of the z=1.86 SLSNe: DES15E2mlf

NASA Astrophysics Data System (ADS)

Pan, Y.-C.; Foley, R. J.; Galbany, L.; Gonzalez-Gaitan, S.; Forster, F.; Hamuy, M.; Prieto, J. L.; Yuan, F.; Tucker, B. E.; Lidman, C.; Martini, P.; Gshwend, Julia; Moller, A.; Zhang, B.; Desai, S.; Paech, K.; Smith, R. C.; Schubnell, M.; Kessler, R.; Lasker, J.; Scolnic, D.; Brout, D. J.; Gladney, L.; Sako, M.; Wolf, R. C.; Brown, P. J.; Krisciunas, K.; Suntzeff, N.; Nichol, R.; Papadopoulos, A.; Childress, M.; D'Andrea, C.; Prajs, S.; Smith, M.; Sullivan, M.; Maartens, R.; Gupta, R.; Kovacs, E.; Kuhlmann, S.; Spinka, H.; Ahn, E.; Finley, D. A.; Frieman, J.; Marriner, J.; Wester, W.; Aldering, G.; Kim, A. G.; Thomas, R. C.; Barbary, K.; Bloom, J. S.; Goldstein, D.; Nugent, P.; Perlmutter, S.; Casas, R.; Castander, F. J.

2015-12-01

We report the spectroscopic classification of DES15E2mlf as a superluminous supernova (SLSN) discovered by the Dark Energy Survey (ATEL #4668). DES15E2mlf was discovered on 7 November 2015 at R.A. = 00:41:33.40, Decl = -43:27:17.2 with r = 24.1 mag. We obtained spectra using GMOS on Gemini-South (520-990nm) on 06 December 2015 which indicated a redshift of z = 1.86 from Mg II 2800 absorption.

What can hafnium isotope ratios arrays tell us about orogenic processes? An insight into geodynamic processes operating in the Alpine/Mediterranean region

NASA Astrophysics Data System (ADS)

Henderson, B.; Murphy, J.; Collins, W. J.; Hand, M. P.

2013-12-01

Over the last decade, technological advances in laser-ablation sampling techniques have resulted in an increase in the number of combined U-Pb-Hf zircon isotope studies used to investigate crustal evolution on a local, regional and global scale. Hafnium isotope arrays over large time scales (>500 myr) have been interpreted to track evolving plate tectonic configurations, and the geological outputs associated with changing plate boundaries. We use the Alpine-Mediterranean region as an example of how hafnium isotope arrays record the geodynamic processes associated with the complex geological evolution of a region. The geology of Alpine-Mediterranean region preserves a complex, semi-continuous tectonic history that extends from the Neoproterozoic to the present day. Major components of the Variscan and Alpine orogens are microcontinental ribbons derived from the northern Gondwanan margin, which were transferred to the Eurasian plate during the opening and closing of the Rheic and Paleo-Tethys Oceans. Convergence of the Eurasian and African plates commenced in the Mid-Late Cretaceous, following the destruction of the Alpine-Tethys Ocean during the terminal breakup of Pangea. In general, convergence occurred slowly and is characterised by northward accretion of Gondwanan fragments, interspersed with subduction of African lithosphere and intermittent roll-back events. A consequence of this geodynamic scenario was periods of granite-dominated magmatism in an arc-backarc setting. New Hf isotope data from the peri-Gondwanan terranes (Iberia, Meguma and Avalonia) and a compilation of existing Phanerozoic data from the Alpine-Mediterranean region, indicate ~500 myr (Cambrian-Recent) of reworking of peri-Gondwanan crust. The eHf array follows a typical crustal evolution pattern (Lu/Hf=0.015) and is considered to reflect reworking of juvenile peri-Gondwanan (Neoproterozoic) crust variably mixed with an older (~1.8-2.0 Ga) source component, probably Eburnian crust from the West

A DPYD variant (Y186C) specific to individuals of African descent in a patient with life-threatening 5-FU toxic effects: potential for an individualized medicine approach.

PubMed

Saif, M Wasif; Lee, Adam M; Offer, Steven M; McConnell, Kathleen; Relias, Valerie; Diasio, Robert B

2014-01-01

5-Fluorouracil (5-FU) is commonly administered as a therapeutic agent for the treatment of various aggressive cancers. Severe toxic reactions to 5-FU have been associated with decreased levels of dihydropyrimidine dehydrogenase (DPD) enzyme activity. Manifestations of 5-FU toxicity typically include cytopenia, diarrhea, stomatitis, mucositis, neurotoxicity, and, in extreme cases, death. A variety of genetic variations in DPYD, the gene encoding DPD, are known to result in decreased DPD enzyme activity and to contribute to 5-FU toxic effects. Recently, it was reported that healthy African American individuals carrying the Y186C DPYD variant (rs115232898) had significantly reduced DPD enzyme activity compared with noncarriers of Y186C. Herein, we describe for the first time, to our knowledge, an African American patient with cancer with the Y186C variant who had severe toxic effects after administration of the standard dose of 5-FU chemotherapy. The patient lacked any additional toxic effect-associated variations in the DPYD gene or the thymidylate synthase (TYMS) promoter. This case suggests that Y186C may have contributed to 5-FU toxicity in this patient and supports the use of Y186C as a predictive marker for 5-FU toxic effects in individuals of African ancestry. Copyright © 2014 Mayo Foundation for Medical Education and Research. Published by Elsevier Inc. All rights reserved.

The energy landscape of glassy dynamics on the amorphous hafnium diboride surface

NASA Astrophysics Data System (ADS)

Nguyen, Duc; Mallek, Justin; Cloud, Andrew N.; Abelson, John R.; Girolami, Gregory S.; Lyding, Joseph; Gruebele, Martin

2014-11-01

Direct visualization of the dynamics of structural glasses and amorphous solids on the sub-nanometer scale provides rich information unavailable from bulk or conventional single molecule techniques. We study the surface of hafnium diboride, a conductive ultrahigh temperature ceramic material that can be grown in amorphous films. Our scanning tunneling movies have a second-to-hour dynamic range and single-point current measurements extend that to the millisecond-to-minute time scale. On the a-HfB2 glass surface, two-state hopping of 1-2 nm diameter cooperatively rearranging regions or "clusters" occurs from sub-milliseconds to hours. We characterize individual clusters in detail through high-resolution (<0.5 nm) imaging, scanning tunneling spectroscopy and voltage modulation, ruling out individual atoms, diffusing adsorbates, or pinned charges as the origin of the observed two-state hopping. Smaller clusters are more likely to hop, larger ones are more likely to be immobile. HfB2 has a very high bulk glass transition temperature Tg, and we observe no three-state hopping or sequential two-state hopping previously seen on lower Tg glass surfaces. The electronic density of states of clusters does not change when they hop up or down, allowing us to calibrate an accurate relative z-axis scale. By directly measuring and histogramming single cluster vertical displacements, we can reconstruct the local free energy landscape of individual clusters, complete with activation barrier height, a reaction coordinate in nanometers, and the shape of the free energy landscape basins between which hopping occurs. The experimental images are consistent with the compact shape of α-relaxors predicted by random first order transition theory, whereas the rapid hopping rate, even taking less confined motion at the surface into account, is consistent with β-relaxations. We make a proposal of how "mixed" features can show up in surface dynamics of glasses.

Method for locating metallic nitride inclusions in metallic alloy ingots

DOEpatents

White, Jack C.; Traut, Davis E.; Oden, Laurance L.; Schmitt, Roman A.

1992-01-01

A method of determining the location and history of metallic nitride and/or oxynitride inclusions in metallic melts. The method includes the steps of labeling metallic nitride and/or oxynitride inclusions by making a coreduced metallic-hafnium sponge from a mixture of hafnium chloride and the chloride of a metal, reducing the mixed chlorides with magnesium, nitriding the hafnium-labeled metallic-hafnium sponge, and seeding the sponge to be melted with hafnium-labeled nitride inclusions. The ingots are neutron activated and the hafnium is located by radiometric means. Hafnium possesses exactly the proper metallurgical and radiochemical properties for this use.

Mechanistic Studies of Hafnium-Pyridyl Amido-Catalyzed 1-Octene Polymerization and Chain Transfer Using Quench-Labeling Methods.

PubMed

Cueny, Eric S; Johnson, Heather C; Anding, Bernie J; Landis, Clark R

2017-08-30

Chromophore quench-labeling applied to 1-octene polymerization as catalyzed by hafnium-pyridyl amido precursors enables quantification of the amount of active catalyst and observation of the molecular weight distribution (MWD) of Hf-bound polymers via UV-GPC analysis. Comparison of the UV-detected MWD with the MWD of the "bulk" (all polymers, from RI-GPC analysis) provides important mechanistic information. The time evolution of the dual-detection GPC data, concentration of active catalyst, and monomer consumption suggests optimal activation conditions for the Hf pre-catalyst in the presence of the activator [Ph 3 C][B(C 6 F 5 ) 4 ]. The chromophore quench-labeling agents do not react with the chain-transfer agent ZnEt 2 under the reaction conditions. Thus, Hf-bound polymeryls are selectively labeled in the presence of zinc-polymeryls. Quench-labeling studies in the presence of ZnEt 2 reveal that ZnEt 2 does not influence the rate of propagation at the Hf center, and chain transfer of Hf-bound polymers to ZnEt 2 is fast and quasi-irreversible. The quench-label techniques represent a means to study commercial polymerization catalysts that operate with high efficiency at low catalyst concentrations without the need for specialized equipment.

Directed evolution of GH43 ß-xylosidase XylBH43 thermal stability and L186 saturation

USDA-ARS?s Scientific Manuscript database

Directed evolution of ß-xylosidase XylBH43 using DNA family shuffling identified three mutations R45K, M69P, and L186Y that affect thermal stability parameter Kt0.5 by -1.8±0.1 º C, 1.7±0.3 º C, and 3.2±0.4 º C, respectively. In addition, a cluster of four mutations near hairpin loop-D83 improved K...

Resistin facilitates VEGF-C-associated lymphangiogenesis by inhibiting miR-186 in human chondrosarcoma cells.

PubMed

Su, Chen-Ming; Tang, Chih-Hsin; Chi, Meng-Ju; Lin, Chih-Yang; Fong, Yi-Chin; Liu, Yueh-Ching; Chen, Wei-Cheng; Wang, Shih-Wei

2018-05-03

Chondrosarcoma is a common primary malignant tumor of the bone that can metastasize through the vascular system to other organs. A key step in the metastatic process, lymphangiogenesis, involves vascular endothelial growth factor-C (VEGF-C). However, the effects of lymphangiogenesis in chondrosarcoma metastasis remain to be clarified. Accumulating evidence shows that resistin, a cytokine secreted from adipocytes and monocytes, also promotes tumor pathogenesis. Notably, chondrosarcoma can easily metastasize. In this study, we demonstrate that resistin enhances VEGF-C expression and lymphatic endothelial cells (LECs)-associated lymphangiogenesis in human chondrosarcoma cells. We also show that resistin triggers VEGF-C-dependent lymphangiogenesis via the c-Src signaling pathway and down-regulating micro RNA (miR)-186. Overexpression of resistin in chondrosarcoma cells significantly enhanced VEGF-C production and LECs-associated lymphangiogenesis in vitro and tumor-related lymphangiogenesis in vivo. Resistin levels were positively correlated with VEGF-C-dependent lymphangiogenesis via the down-regulation of miR-186 expression in clinical samples from chondrosarcoma tissue. This study is the first to evaluate the mechanism underlying resistin-induced promotion of LECs-associated lymphangiogenesis via the upregulation of VEGF-C expression in human chondrosarcomas. We suggest that resistin may represent a molecular target in VEGF-C-associated tumor lymphangiogenesis in chondrosarcoma metastasis. Copyright © 2018 Elsevier Inc. All rights reserved.

Characteristics of laser produced plasmas of hafnium and tantalum in the 1-7 nm region

NASA Astrophysics Data System (ADS)

Li, Bowen; Otsuka, Takamitsu; Sokell, Emma; Dunne, Padraig; O'Sullivan, Gerry; Hara, Hiroyuki; Arai, Goki; Tamura, Toshiki; Ono, Yuichi; Dinh, Thanh-Hung; Higashiguchi, Takeshi

2017-11-01

Soft X-ray (SXR) spectra from hafnium and tantalum laser produced plasmas were recorded in the 1-7 nm region using two Nd:YAG lasers with pulse lengths of 170 ps and 10 ns, respectively, operating at a range of power densities. The maximum focused peak power density was 2. 3 × 1014 W cm-2 for 170 ps pulses and 1. 8 × 1012 W cm-2 for 10 ns pulses, respectively. Two intense quasicontinuous intensity bands resulting from n = 4 - n = 4 and n = 4 - n = 5 unresolved transition arrays (UTAs) dominate both sets of experimental spectra. Comparison with calculations performed with the Cowan suite of atomic structure codes as well as consideration of previous experimental and theoretical results aided identification of the most prominent features in the spectra. For the 10 ns spectrum, the highest ion stage that could be identified from the n = 4 - n = 5 arrays were lower than silver-like Hf25+ and Ta26+ (which has a 4 d 104 f ground configuration) indicating that the plasma temperature attained was too low to produce ions with an outermost 4 d subshell, while for the 170 ps plasmas the presence of significantly higher stages was deduced and lines due to 4 d-5 p transitions were clearly evident. Furthermore, we show an enhancement of emission from tantalum using dual laser irradiation, and the effect of pre-pulse durations and delay times between two pulses are demonstrated.

High activity Rhenium-186 HEDP with autologous peripheral blood stem cell rescue: a phase I study in progressive hormone refractory prostate cancer metastatic to bone

PubMed Central

O'Sullivan, J M; McCready, V R; Flux, G; Norman, A R; Buffa, F M; Chittenden, S; Guy, M; Pomeroy, K; Cook, G; Gadd, J; Treleaven, J; Al-Deen, A; Horwich, A; Huddart, R A; Dearnaley, D P

2002-01-01

We tested the feasibility and toxicity of high activities Rhenium-186 hydroxyethylidene diphosphonate, with peripheral blood stem cell rescue in patients with progressive hormone refractory prostate cancer metastatic to bone. Twenty-five patients received between 2500 and 5000 MBq of Rhenium-186 hydroxyethylidene diphosphonate followed 14 days later by the return of peripheral blood peripheral blood stem cells. Activity limiting toxicity was defined as grade III haematological toxicity, lasting at least 7 days, or grade IV haematological toxicity of any duration or any serious unexpected toxicity. Activity limiting toxicity occurred in two of six who received activities of 5000 MBq and maximum tolerated activity was defined at this activity level. Prostate specific antigen reductions of 50% or more lasting at least 4 weeks were seen in five of the 25 patients (20%) all of whom received more than 3500 MBq of Rhenium-186 hydroxyethylidene diphosphonate. The actuarial survival at 1 year is 54%. Administered activities of 5000 MBq of Rhenium-186 hydroxyethylidene diphosphonate are feasible using autologous peripheral blood peripheral blood stem cell rescue in patients with progressive hormone refractory prostate cancer metastatic to bone. The main toxicity is thrombocytopaenia, which is short lasting. A statistically significant activity/prostate specific antigen response was seen. We have now commenced a Phase II trial to further evaluate response rates. British Journal of Cancer (2002) 86, 1715–1720. doi:10.1038/sj.bjc.6600348 www.bjcancer.com © 2002 Cancer Research UK PMID:12087455

Materials properties of hafnium and zirconium silicates: Metal interdiffusion and dopant penetration studies

NASA Astrophysics Data System (ADS)

Quevedo Lopez, Manuel Angel

Hafnium and Zirconium based gate dielectrics are considered potential candidates to replace SiO2 or SiON as the gate dielectric in CMOS processing. Furthermore, the addition of nitrogen into this pseudo-binary alloy has been shown to improve their thermal stability, electrical properties, and reduce dopant penetration. Because CMOS processing requires high temperature anneals (up to 1050°C), it is important to understand the diffusion properties of any metal associated with the gate dielectric in silicon at these temperatures. In addition, dopant penetration from the doped polysilicon gate into the Si channel at these temperatures must also be studied. Impurity outdiffusion (Hf, Zr) from the dielectric, or dopant (B, As, P) penetration through the dielectric into the channel region would likely result in deleterious effects upon the carrier mobility. In this dissertation extensive thermal stability studies of alternate gate dielectric candidates ZrSixOy and HfSixO y are presented. Dopant penetration studies from doped-polysilicon through HfSixOy and HfSixOyNz are also presented. Rutherford Backscattering Spectroscopy (RBS), Heavy Ion RBS (HI-RBS), X-ray Photoelectron Spectroscopy (XPS), High Resolution Transmission Electron Microscopy (HR-TEM), and Time of Flight and Dynamic Secondary Ion Mass Spectroscopy (ToF-SIMS, D-SIMS) methods were used to characterize these materials. The dopant diffusivity is calculated by modeling of the dopant profiles in the Si substrate. In this disseration is reported that Hf silicate films are more stable than Zr silicate films, from the metal interdiffusion point of view. On the other hand, dopant (B, As, and P) penetration is observed for HfSixO y films. However, the addition of nitrogen to the Hf - Si - O systems improves the dopant penetration properties of the resulting HfSi xOyNz films.

Fusion and quasifission studies for the 40Ca+186W,192Os reactions

NASA Astrophysics Data System (ADS)

Prasad, E.; Hinde, D. J.; Williams, E.; Dasgupta, M.; Carter, I. P.; Cook, K. J.; Jeung, D. Y.; Luong, D. H.; Palshetkar, C. S.; Rafferty, D. C.; Ramachandran, K.; Simenel, C.; Wakhle, A.

2017-09-01

Background: All elements above atomic number 113 have been synthesized using hot fusion reactions with calcium beams on statically deformed actinide target nuclei. Quasifission and fusion-fission are the two major mechanisms responsible for the very low production cross sections of superheavy elements. Purpose: To achieve a quantitative measurement of capture and quasifission characteristics as a function of beam energy in reactions forming heavy compound systems using calcium beams as projectiles. Methods: Fission fragment mass-angle distributions were measured for the two reactions 40Ca+186W and 40C+192Os, populating 226Pu and 232Cm compound nuclei, respectively, using the Heavy Ion Accelerator Facility and CUBE spectrometer at the Australian National University. Mass ratio distributions, angular distributions, and total fission cross sections were obtained from the experimental data. Simulations to match the features of the experimental mass-angle distributions were performed using a classical phenomenological approach. Results: Both 40Ca+186W and 40C+192Os reactions show strong mass-angle correlations at all energies measured. A maximum fusion probability of 60 -70 % is estimated for the two reactions in the energy range of the present study. Coupled-channels calculations assuming standard Woods-Saxon potential parameters overpredict the capture cross sections. Large nuclear potential diffuseness parameters ˜1.5 fm are required to fit the total capture cross sections. The presence of a weak mass-asymmetric quasifission component attributed to the higher angular momentum events can be reproduced with a shorter average sticking time but longer mass-equilibration time constant. Conclusions: The deduced above-barrier capture cross sections suggest that the dissipative processes are already occurring outside the capture barrier. The mass-angle correlations indicate that a compact shape is not achieved for deformation aligned collisions with lower capture barriers

POX 186: the ultracompact blue compact dwarf galaxy reveals its nature

NASA Astrophysics Data System (ADS)

Doublier, V.; Kunth, D.; Courbin, F.; Magain, P.

2000-01-01

High resolution, ground based R and I band observations of the ultra compact dwarf galaxy POX 186 are presented. The data, obtained with the ESO New Technology Telescope (NTT), are analyzed using a new deconvolution algorithm which allows one to resolve the innermost regions of this stellar-like object into three Super-Star Clusters (SSC). Upper limits to both masses (M ~ 105 Msun) and physical sizes (<=60pc) of the SSCs are set. In addition, and maybe most importantly, extended light emission underlying the compact star-forming region is clearly detected in both bands. The R-I color rules out nebular Hα contamination and is consistent with an old stellar population. This casts doubt on the hypothesis that Blue Compact Dwarf Galaxies (BCDG) are young galaxies. based on observations carried out at NTT in La Silla, operated by the European Southern Observatory, during Director's Discretionary Time.

Structure of the 4^+3 States in ^186,188Os

NASA Astrophysics Data System (ADS)

Phillips, A. A.; Garrett, P. E.; Demand, G. A.; Finlay, P.; Green, K. L.; Leach, K. G.; Schumaker, M. A.; Svensson, C. E.; Wong, J.; Hertenberger, R.; Faestermann, T.; Krücken, R.; Wirth, H.-F.; Bettermann, L.; Braun, N.; Burke, D. G.

2007-10-01

The structures of 4^+3 states in the Os nuclei have been the subject of debate for the past several decades. Based on measured B(E2) values, they were interpreted in ^186-192Os as K^π=4^+ two-phonon γ vibrations, whereas inelastic scattering results, and single-proton transfer (d,^3He) and (t,α) imply a hexadecapole phonon description. Uncertainties in the (t,α) reaction mechanism, however, were cited as preventing a firm conclusion based on those data. To help clarify the nature of these K^π=4^+ bands, we have performed a (^3He,d) stripping reaction on targets of ^185,187Re using 30 MeV ^3He beams provided by the MP-tandem facility of the LMU/TUM in Garching. With an energy resolution of 13 keV, the deuterons were analyzed at 9 angles ranging from 5^o to 50^o with the Q3D spectrograph, and absolute cross sections were obtained for levels up to 3 MeV in excitation energy. Preliminary results will be presented.

186 K Operation of Terahertz Quantum-Cascade Lasers Based on a Diagonal Design

NASA Technical Reports Server (NTRS)

Kumar, Sushil; Hu, Qing; Reno, John L.

2009-01-01

Resonant-phonon terahertz quantum-cascade lasers operating up to a heat-sink temperature of 186 K are demonstrated. This record temperature performance is achieved based on a diagonal design, with the objective to increase the upper-state lifetime and therefore the gain at elevated temperatures. The increased diagonality also lowers the operating current densities by limiting the flow of parasitic leakage current. Quantitatively, the diagonality is characterized by a radiative oscillator strength that is smaller by a factor of two from the least of any previously published designs. At the lasing frequency of 3.9 THz, 63 mW of peak optical power was measured at 5 K, and approximately 5 mW could still be detected at 180 K.

Processing development of 4 tantalum carbide-hafnium carbide and related carbides and borides for extreme environments

NASA Astrophysics Data System (ADS)

Gaballa, Osama Gaballa Bahig

Carbides, nitrides, and borides ceramics are of interest for many applications because of their high melting temperatures and good mechanical properties. Wear-resistant coatings are among the most important applications for these materials. Materials with high wear resistance and high melting temperatures have the potential to produce coatings that resist degradation when subjected to high temperatures and high contact stresses. Among the carbides, Al4SiC4 is a low density (3.03 g/cm3), high melting temperature (>2000°C) compound, characterized by superior oxidation resistance, and high compressive strength. These desirable properties motivated this investigation to (1) obtain high-density Al4SiC4 at lower sintering temperatures by hot pressing, and (2) to enhance its mechanical properties by adding WC and TiC to the Al4SiC4. Also among the carbides, tantalum carbide and hafnium carbide have outstanding hardness; high melting points (3880°C and 3890°C respectively); good resistance to chemical attack, thermal shock, and oxidation; and excellent electronic conductivity. Tantalum hafnium carbide (Ta4HfC 5) is a 4-to-1 ratio of TaC to HfC with an extremely high melting point of 4215 K (3942°C), which is the highest melting point of all currently known compounds. Due to the properties of these carbides, they are considered candidates for extremely high-temperature applications such as rocket nozzles and scramjet components, where the operating temperatures can exceed 3000°C. Sintering bulk components comprised of these carbides is difficult, since sintering typically occurs above 50% of the melting point. Thus, Ta4 HfC5 is difficult to sinter in conventional furnaces or hot presses; furnaces designed for very high temperatures are expensive to purchase and operate. Our research attempted to sinter Ta4HfC5 in a hot press at relatively low temperature by reducing powder particle size and optimizing the powder-handling atmosphere, milling conditions, sintering

Thermal conductivity and thermal boundary resistance of atomic layer deposited high-k dielectric aluminum oxide, hafnium oxide, and titanium oxide thin films on silicon

NASA Astrophysics Data System (ADS)

Scott, Ethan A.; Gaskins, John T.; King, Sean W.; Hopkins, Patrick E.

2018-05-01

The need for increased control of layer thickness and uniformity as device dimensions shrink has spurred increased use of atomic layer deposition (ALD) for thin film growth. The ability to deposit high dielectric constant (high-k) films via ALD has allowed for their widespread use in a swath of optical, optoelectronic, and electronic devices, including integration into CMOS compatible platforms. As the thickness of these dielectric layers is reduced, the interfacial thermal resistance can dictate the overall thermal resistance of the material stack compared to the resistance due to the finite dielectric layer thickness. Time domain thermoreflectance is used to interrogate both the thermal conductivity and the thermal boundary resistance of aluminum oxide, hafnium oxide, and titanium oxide films on silicon. We calculate a representative design map of effective thermal resistances, including those of the dielectric layers and boundary resistances, as a function of dielectric layer thickness, which will be of great importance in predicting the thermal resistances of current and future devices.

SU-F-T-22: Clinical Implications When Using TG-186 (ACE) Heterogeneity Software

DOE Office of Scientific and Technical Information (OSTI.GOV)

Likhacheva, A; Grade, E; Sadeghi, A

Purpose: The purpose of this study is to compare dosimetric calculations using traditional TG-43 formalism and Oncentra Brachy Advanced Collapsed cone Engine (ACE) TG-186 calculation algorithm in clinical setting. Methods: We analyzed dosimetry of four patients treated with accelerated partial breast irradiation using a multi-channel intracavitary device (SAVI). All patients were treated to 34 Gy in 10 fractions using a high-dose-rate (192) Ir source. The plans were designed and treated using the TG-43 model. ACE was used to assess the effect heterogeneity correction on various dosimetric parameters. Mass density was estimated using Hounsfield units. Results: Compared to TG-43 formalism, ACEmore » estimated lower doses to targets and organs at risk. The mean difference was 19.8% (range 15.3–24.1%) for PTV-eval V200, 12.0% (range 9.7–17.7%) for PTV-eval V150, 4.3% (range 3.3–6.5%) for PTV-eval D95, 3.3% (range 1.4–5.4%) for PTV-eval D90, 5.4% (range 2.9–9.9%) for maximum rib dose, and 5.7% (2.4–7.4%) for maximum skin dose. There was no correlation between the magnitude of the difference and the PTV-eval volume, air volume, or tissue-applicator conformance. Conclusion: Based on our preliminary study, the TG-43 algorithm appears to overestimate the dose to targets and organs at risk when compared to the ACE TG-186 software. We hypothesize that air adjacent to the SAVI struts contributes to lack of scatter thereby contributing a significant difference in dose calculation when using ACE. We believe that ACE calculation provides a more realistic isodose distribution than TG-43. We plan to further investigate the impact of heterogeneity correction on brachytherapy planning for a wide variety of clinical scenarios, include skin, cervix/uterus, prostate, and lung.« less

Oxidation Characterization of Hafnium-Based Ceramics Fabricated by Hot Pressing and Electric Field-Assisted Sintering

NASA Technical Reports Server (NTRS)

Gasch, Matt; Johnson, Sylvia; Marschall, Jochen

2010-01-01

Ceramic borides, such as hafnium diboride (HfB2) and zirconium diboride (ZrB2), are members of a family of materials with extremely high melting temperatures referred to as Ultra High Temperature Ceramics (UHTCs). UHTCs constitute a class of promising materials for use in high temperature applications, such as sharp leading edges on future-generation hypersonic flight vehicles, because of their high melting points. The controlled development of microstructure has become important to the processing of UHTCs, with the prospect of improving their mechanical and thermal properties. The improved oxidation resistance of HfB2 has also become important if this material is to be successfully used at temperatures above 2000 C. Furthermore, the use of UHTCs on the leading edges of vehicles traveling at hypersonic speeds will mean exposure to a mixed oxidation environment comprised of both molecular and atomic oxygen. The current study has investigated the high-temperature oxidation behavior of HfB2-based materials in a pure O2 environment, as well as in environments containing different levels of dissociated oxygen (O/O2). Materials were processed by two techniques: conventional hot pressing (HP) and electric field-assisted sintering (FAS). Their oxidation behavior was evaluated in both a tube furnace at 1250 C for 3 hours and in a simulated re-entry environment in the Advanced Heating Facility (AHF) arcjet at NASA Ames Research Center, during a 10-minute exposure to a cold wall heat flux of 250W/sq cm and stagnation pressure of 0.1-0.2 atm. The microstructure of the different materials was characterized before and after oxidation using scanning electron microscopy (SEM).

18.6 K single-stage high frequency multi-bypass coaxial pulse tube cryocooler

NASA Astrophysics Data System (ADS)

Chen, Liubiao; Jin, Hai; Wang, Junjie; Zhou, Yuan; Zhu, Wenxiu; Zhou, Qiang

2013-02-01

A single-stage high frequency multi-bypass coaxial pulse tube cryocooler (PTC) has been developed for physical experiments. The performance characteristics are presented. At present, the cooler has reached the lowest temperature of 18.6 K with an electric input power of 268 W, which is the reported lowest temperature for single-stage high frequency PTC. The cooler typically provides 0.2 W at 20.6 K and 0.5 W at 24.1 K with the input power of 260 W at 300 K ambient temperature. The cooperation phase adjustment method of multi-bypass and double-inlet shows its advantages in experiments, they might be the best way to get temperature below 20 K for single-stage high frequency PTC. The temperature stability of the developed PTC is also observed.

Post-hoc analysis of randomised, placebo-controlled, double-blind study (MCI186-19) of edaravone (MCI-186) in amyotrophic lateral sclerosis.

PubMed

Takei, Koji; Takahashi, Fumihiro; Liu, Shawn; Tsuda, Kikumi; Palumbo, Joseph

2017-10-01

Post-hoc analyses of the ALS Functional Rating Scale-Revised (ALSFRS-R) score data, the primary endpoint in the 24-week double-blind placebo-controlled study of edaravone (MCI186-19, NCT01492686), were performed to confirm statistical robustness of the result. The previously reported original analysis had used a last observation carried forward (LOCF) method and also excluded patients with fewer than three completed treatment cycles. The post-hoc sensitivity analyses used different statistical methods as follows: 1) including all patients regardless of treatment cycles received (ALL LOCF); 2) a mixed model for repeated measurements (MMRM) analysis; and 3) the Combined Assessment of Function and Survival (CAFS) endpoint. Findings were consistent with the original primary analysis in showing superiority of edaravone over placebo. We also investigated the distribution of change in ALSFRS-R total score across all patients in the study as well as which ALSFRS-R items and domains may have contributed to the overall efficacy findings. The distribution of changes in ALSFRS-R total score from baseline to the end of cycle 6 (ALL LOCF) shifted in favour of edaravone compared to placebo. Edaravone was descriptively favoured for each ALSFRS-R item and each of the four ALSFRS-R domains at the end of cycle 6 (ALL LOCF), suggesting a generalised effect of edaravone in slowing functional decline across all anatomical regions. The effect of edaravone appeared to be similar in patients with bulbar onset and limb onset. Together, these observations would be consistent with its putative neuroprotective effects against the development of oxidative damage unspecific to anatomical regions.

Evolution of the mechanical and tribological properties of DLC thin films doped with low-concentration hafnium on 316L steel

NASA Astrophysics Data System (ADS)

Qi, Meng; Xiao, Jianrong; Gong, Chenyang; Jiang, Aihua; Chen, Yong

2018-01-01

Low concentrations (<1 at%) of hafnium doped into diamond-like thin films (Hf-DLC) were deposited on 316L stainless steel and silicon (1 0 0) substrates by magnetron sputtering to attain superior mechanical and tribological properties. Ar and CH4 were used as source gases. The microstructure, chemical composition, and morphology of the Hf-DLC thin films in various concentrations were analyzed using x-ray diffraction, Raman spectroscopy, x-ray photoelectron spectroscopy, scanning electron microscopy and atomic force microscopy. Results showed that Hf species transferred from the particulate microstructure to Hf carbide phases, and the surface roughness increased monotonically with increasing Hf concentration. Moreover, the hardness and elastic modulus exhibited high values when the doped Hf concentration was 0.42 at%. Similarly, the tribological behaviors and wear life of Hf-DLC thin films had a low friction coefficient and excellent wear resistance at 0.42 at% Hf concentration. Therefore, 0.42 at% Hf is an optimal doping concentration to improve the mechanical and tribological properties of DLC thin films. Generally, the use of low-concentration Hf doping into DLC thin films is novel, and the present results provide guidance for the selection of suitable and effective concentration to optimize Hf-DLC thin films with superior performance.

Preliminary report, cruises L1-86-NC and L2-86-NC, Escanaba Trough, Gorda Ridge

USGS Publications Warehouse

Morton, J.L.; Normark, W.R.; Ross, Stephanie L.; Koski, R.A.; Holmes, M.L.; Shanks, Wayne C.; Zierenberg, R.A.; Lyle, M.W.; Benninger, L.M.

1987-01-01

Eight large (up to 200 m across) and many small massive sulfide deposits were photographed and sampled at the sediment-covered Escanaba Trough, southern Gorda Ridge, during S.P. Lee cruises L1-86-NC and L2-86-NC in 1986. The deposits are associated with two volcanic edifices within the sedimentary fill along the axis of Escanaba Trough. The sulfide and other hydrothermal minerals are deposited on the seafloor as well as within the sedimentary section. High concentrations of Pb and As in some of the sulfide samples indicates significant interaction between hydrothermal fluids and sediment at depth.

God's punishment and public goods : A test of the supernatural punishment hypothesis in 186 world cultures.

PubMed

Johnson, Dominic D P

2005-12-01

Cooperation towards public goods relies on credible threats of punishment to deter cheats. However, punishing is costly, so it remains unclear who incurred the costs of enforcement in our evolutionary past. Theoretical work suggests that human cooperation may be promoted if people believe in supernatural punishment for moral transgressions. This theory is supported by new work in cognitive psychology and by anecdotal ethnographic evidence, but formal quantitative tests remain to be done. Using data from 186 societies around the globe, I test whether the likelihood of supernatural punishment-indexed by the importance of moralizing "high gods"-is associated with cooperation.

Long noncoding RNA PVT1 promotes EMT via mediating microRNA-186 targeting of Twist1 in prostate cancer.

PubMed

Chang, Zhongwen; Cui, Jun; Song, Yongsheng

2018-05-15

The pathogenesis and the underlying mechanism of endothelial-mesenchymal transition in prostate cancer remain unclear. Plasmacytoma variant translocation 1 (PVT1), a novel long non-coding RNA maps to 8q24.21, and in many tumor studies the up-regulation of PVT1 has already been reported. PVT1 is closely related to tumor cell proliferation, invasion, and metastasis. In this study, we employed a combination of techniques to study the role of PVT1 in prostate cancer, which included bioinformatic analysis, Western blotting and cell migration assays of prostate cancer cell lines. We report that PVT1 promotes prostate cancer invasion and metastasis by modulating EMT. Furthermore, PVT1 can promote EMT by up-regulation of Twist1, a transcription factor associated with EMT. We then confirmed that PVT1 acts as a sponge for miRNA-186-5p and positively regulates Twist1 by a sponge effect. Therefore, this study has revealed a novel MECHANISM for the promotion of EMT in prostate cancer by PVT1. Our findings suggest that the PVT1/miR-186/Twist1 regulatory axis may be a new therapeutic target for prostate cancer. Copyright © 2018. Published by Elsevier B.V.

L2₁ and XA Ordering Competition in Hafnium-Based Full-Heusler Alloys Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb).

PubMed

Wang, Xiaotian; Cheng, Zhenxiang; Wang, Wenhong

2017-10-20

For theoretical designing of full-Heusler based spintroinc materials, people have long believed in the so-called Site Preference Rule (SPR). Very recently, according to the SPR, there are several studies on XA-type Hafnium-based Heusler alloys X₂YZ, i.e., Hf₂VAl, Hf₂CoZ (Z = Ga, In) and Hf₂CrZ (Z = Al, Ga, In). In this work, a series of Hf₂-based Heusler alloys, Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb), were selected as targets to study the site preferences of their atoms by first-principle calculations. It has been found that all of them are likely to exhibit the L2₁-type structure instead of the XA one. Furthermore, we reveal that the high values of spin-polarization of XA-type Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb) alloys have dropped dramatically when they form the L2₁-type structure. Also, we prove that the electronic, magnetic, and physics nature of these alloys are quite different, depending on the L2₁-type or XA-type structures.

Integration of seismic interpretation and petrophysical studies on Hawaz Formation in J-field NC-186 concession, Northwest Murzuq basin, Libya

NASA Astrophysics Data System (ADS)

Mohamed, A. K.; Selim, E. I.; Kashlaf, A.

2016-12-01

This study has been carried out by the integration of seismic interpretations and the well-logging analysis of ten wells distributed in J-field of concession NC-186, Murzuq basin, Libya. Twenty (3D) seismic lines and ten wells have been analyzed. The results of this study indicated that, the main reservoir in this concession is Hawaz Formation. Hawaz has been split into 8 units with a subdivision of Hawaz H4 into three subunits with the objective of better characterization of the three general fine upward intervals. The lower interval of H4 zone presents the better reservoir properties. The depth of reflector H4 ranges from 4100 ft in the northwestern part of the study area and increases to 4600 ft in the southeastern part of the study area. In this study, the outline of the Hawaz paleohighs which is NC-186 Field ;J; is generally trending in the NW-SE direction. The well logging analysis particularly quick look interpretation indicates that Hawaz Formation in the studied wells is mainly oil-bearing with some water-bearing sand levels at the horizons from H4 to and H6 which are potentially the main reservoirs. The water bearing zones are beyond these horizons starting from the sub-horizon H6c and the oil water contact is probably at depth 4495 ft. The crossplot of porosity-saturation for H5 and H6b indicates firmly that these horizons are indeed at irreducible state and will produce mainly oil as indicated in J4-NC186 well, while the crossplot of H8 shows wide scattering of points which is the main characteristic for water producing horizon. The depth of Hawaz Formation H4 is more than 4160 ft in J4, J12 and J16 wells in the northwestern parts of this field and increases to 4400 in the central part of the concession at well J1.

186Os-187Os and highly siderophile element abundance systematics of the mantle revealed by abyssal peridotites and Os-rich alloys

NASA Astrophysics Data System (ADS)

Day, James M. D.; Walker, Richard J.; Warren, Jessica M.

2017-03-01

Abyssal peridotites are oceanic mantle fragments that were recently processed through ridges and represent residues of both modern and ancient melting. To constrain the nature and timing of melt depletion processes, and the composition of the mantle, we report high-precision Os isotope data for abyssal peridotites from three ocean basins, as well as for Os-rich alloys, primarily from Mesozoic ophiolites. These data are complemented by whole-rock highly siderophile element (HSE: Os, Ir, Ru, Pt, Pd, Re), trace- and major-element abundances for the abyssal peridotites, which are from the Southwest Indian (SWIR), Central Indian (CIR), Mid-Atlantic (MAR) and Gakkel Ridges. The results reveal a limited role for melt refertilization or secondary alteration processes in modifying abyssal peridotite HSE compositions. The abyssal peridotites examined have experienced variable melt depletion (2% to >16%), which occurred >0.5 Ga ago for some samples. Abyssal peridotites typically exhibit low Pd/Ir and, combined with high-degrees of estimated total melt extraction, imply that they were relatively refractory residues prior to incorporation into their present ridge setting. Recent partial melting processes and mid-ocean ridge basalt (MORB) generation therefore played a limited role in the chemical evolution of their precursor mantle domains. The results confirm that many abyssal peridotites are not simple residues of recent MORB source melting, having a more complex and long-lived depletion history. Peridotites from the Gakkel Ridge, SWIR, CIR and MAR indicate that the depleted MORB mantle has 186Os/188Os of 0.1198356 ± 21 (2SD). The Phanerozoic Os-rich alloys yield an average 186Os/188Os within uncertainty of abyssal peridotites (0.1198361 ± 20). Melt depletion trends defined between Os isotopes and melt extraction indices (e.g., Al2O3) allow an estimate of the primitive mantle (PM) composition, using only abyssal peridotites. This yields 187Os/188Os (0.1292 ± 25), and 186Os

Suppression of magnetic order in CaCo1.86As2 with Fe substitution: Magnetization, neutron diffraction, and x-ray diffraction studies of Ca (Co1-xFex) yAs2

NASA Astrophysics Data System (ADS)

Jayasekara, W. T.; Pandey, Abhishek; Kreyssig, A.; Sangeetha, N. S.; Sapkota, A.; Kothapalli, K.; Anand, V. K.; Tian, W.; Vaknin, D.; Johnston, D. C.; McQueeney, R. J.; Goldman, A. I.; Ueland, B. G.

2017-02-01

Magnetization, neutron diffraction, and high-energy x-ray diffraction results for Sn-flux grown single-crystal samples of Ca (Co1-xFex) yAs2 , 0 ≤x ≤1 , 1.86 ≤y ≤2 , are presented and reveal that A-type antiferromagnetic order, with ordered moments lying along the c axis, persists for x ≲0.12 (1 ) . The antiferromagnetic order is smoothly suppressed with increasing x , with both the ordered moment and Néel temperature linearly decreasing. Stripe-type antiferromagnetic order does not occur for x ≤0.25 , nor does ferromagnetic order for x up to at least x =0.104 , and a smooth crossover from the collapsed-tetragonal (cT) phase of CaCo1.86As2 to the tetragonal (T) phase of CaFe2As2 occurs. These results suggest that hole doping CaCo1.86As2 has a less dramatic effect on the magnetism and structure than steric effects due to substituting Sr for Ca.

High rate buffer layer for IBAD MgO coated conductors

DOEpatents

Foltyn, Stephen R [Los Alamos, NM; Jia, Quanxi [Los Alamos, NM; Arendt, Paul N [Los Alamos, NM

2007-08-21

Articles are provided including a base substrate having a layer of an oriented material thereon, and, a layer of hafnium oxide upon the layer of an oriented material. The layer of hafnium oxide can further include a secondary oxide such as cerium oxide, yttrium oxide, lanthanum oxide, scandium oxide, calcium oxide and magnesium oxide. Such articles can further include thin films of high temperature superconductive oxides such as YBCO upon the layer of hafnium oxide or layer of hafnium oxide and secondary oxide.

A COMPARISON OF EXPERIMENTS AND THREE-DIMENSIONAL ANALYSIS TECHNIQUES. PART II. UNPOISONED UNIFORM SLAB CORE WITH A PARTIALLY INSERTED HAFNIUM ROD AND A PARTIALLY INSERTED WATER GAP

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roseberry, R.J.

The experimental measurements and nuclear analysis of a uniformly loaded, unpoisoned slab core with a partially inserted hafnium rod and/or a partially inserted water gap are described. Comparisons of experimental data with calculated results of the UFO core and flux synthesis techniques are given. It is concluded that one of the flux synthesis techniques and the UFO code are able to predict flux distributions to within approximately -5% of experiment for most cases, with a maximum error of approximately -10% for a channel at the core- reflector boundary. The second synthesis technique failed to give comparable agreement with experiment evenmore » when various refinements were used, e.g. increasing the number of mesh points, performing the flux synthesis technique of iteration, and spectrum-weighting the appropriate calculated fluxes through the use of the SWAKRAUM code. These results are comparable to those reported in Part I of this study. (auth)« less

High-precision measurement of (186)Os/(188)Os and (187)Os/(188)Os: isobaric oxide corrections with in-run measured oxygen isotope ratios.

PubMed

Chu, Zhu-Yin; Li, Chao-Feng; Chen, Zhi; Xu, Jun-Jie; Di, Yan-Kun; Guo, Jing-Hui

2015-09-01

We present a novel method for high precision measurement of (186)Os/(188)Os and (187)Os/(188)Os ratios, applying isobaric oxide interference correction based on in-run measurements of oxygen isotopic ratios. For this purpose, we set up a static data collection routine to measure the main Os(16)O3(-) ion beams with Faraday cups connected to conventional 10(11) amplifiers, and (192)Os(16)O2(17)O(-) and (192)Os(16)O2(18)O(-) ion beams with Faraday cups connected to 10(12) amplifiers. Because of the limited number of Faraday cups, we did not measure (184)Os(16)O3(-) and (189)Os(16)O3(-) simultaneously in-run, but the analytical setup had no significant influence on final (186)Os/(188)Os and (187)Os/(188)Os data. By analyzing UMd, DROsS, an in-house Os solution standard, and several rock reference materials, including WPR-1, WMS-1a, and Gpt-5, the in-run measured oxygen isotopic ratios were proven to present accurate Os isotopic data. However, (186)Os/(188)Os and (187)Os/(188)Os data obtained with in-run O isotopic compositions for the solution standards and rock reference materials show minimal improvement in internal and external precision, compared to the conventional oxygen correction method. We concluded that, the small variations of oxygen isotopes during OsO3(-) analytical sessions are probably not the main source of error for high precision Os isotopic analysis. Nevertheless, use of run-specific O isotopic compositions is still a better choice for Os isotopic data reduction and eliminates the requirement of extra measurements of the oxygen isotopic ratios.

Comparison of TG-43 and TG-186 in breast irradiation using a low energy electronic brachytherapy source.

PubMed

White, Shane A; Landry, Guillaume; Fonseca, Gabriel Paiva; Holt, Randy; Rusch, Thomas; Beaulieu, Luc; Verhaegen, Frank; Reniers, Brigitte

2014-06-01

The recently updated guidelines for dosimetry in brachytherapy in TG-186 have recommended the use of model-based dosimetry calculations as a replacement for TG-43. TG-186 highlights shortcomings in the water-based approach in TG-43, particularly for low energy brachytherapy sources. The Xoft Axxent is a low energy (<50 kV) brachytherapy system used in accelerated partial breast irradiation (APBI). Breast tissue is a heterogeneous tissue in terms of density and composition. Dosimetric calculations of seven APBI patients treated with Axxent were made using a model-based Monte Carlo platform for a number of tissue models and dose reporting methods and compared to TG-43 based plans. A model of the Axxent source, the S700, was created and validated against experimental data. CT scans of the patients were used to create realistic multi-tissue/heterogeneous models with breast tissue segmented using a published technique. Alternative water models were used to isolate the influence of tissue heterogeneity and backscatter on the dose distribution. Dose calculations were performed using Geant4 according to the original treatment parameters. The effect of the Axxent balloon applicator used in APBI which could not be modeled in the CT-based model, was modeled using a novel technique that utilizes CAD-based geometries. These techniques were validated experimentally. Results were calculated using two dose reporting methods, dose to water (Dw,m) and dose to medium (Dm,m), for the heterogeneous simulations. All results were compared against TG-43-based dose distributions and evaluated using dose ratio maps and DVH metrics. Changes in skin and PTV dose were highlighted. All simulated heterogeneous models showed a reduced dose to the DVH metrics that is dependent on the method of dose reporting and patient geometry. Based on a prescription dose of 34 Gy, the average D90 to PTV was reduced by between ~4% and ~40%, depending on the scoring method, compared to the TG-43 result. Peak

What can (^3He,d) tell us about the structure of ^186,188Os

NASA Astrophysics Data System (ADS)

Phillips, A. A.; Garrett, P. E.; Demand, G. A.; Finlay, P.; Green, K. L.; Leach, K. G.; Schumaker, M. A.; Svensson, C. E.; Wong, J.; Hertenberger, R.; Faestermann, T.; Krücken, R.; Wirth, H.-F.; Bettermann, L.; Braun, N.; Burke, D. G.

2008-10-01

The structure of Os nuclei are of interest for a number of reasons including a debate over the vibrational nature of the K^π=4^+ bands, and a shape transition from well-deformed prolate to γ-soft oblate as the number of neutrons increases. In order to investigate the structure of ^186,188Os, we have performed a (^3He,d) reaction on targets of ^185,187Re. The 30 MeV ^3He beams were obtained from the LMU/TUM Tandem Accelerator facility, and the Q3D spectrometer was used to analyze deuterons with 13 keV energy resolution. The absolute cross sections were measured at 9 angles from 5^o to 50^o up to ˜3 MeV in excitation energy. Fingerprint patterns are used to identify orbitals coupled to the 5/2^+[402]π target configuration.

Thermal neutron radiative capture cross-section of 186W(n, γ)187W reaction

NASA Astrophysics Data System (ADS)

Tan, V. H.; Son, P. N.

2016-06-01

The thermal neutron radiative capture cross section for 186W(n, γ)187W reaction was measured by the activation method using the filtered neutron beam at the Dalat research reactor. An optimal composition of Si and Bi, in single crystal form, has been used as neutron filters to create the high-purity filtered neutron beam with Cadmium ratio of Rcd = 420 and peak energy En = 0.025 eV. The induced activities in the irradiated samples were measured by a high resolution HPGe digital gamma-ray spectrometer. The present result of cross section has been determined relatively to the reference value of the standard reaction 197Au(n, γ)198Au. The necessary correction factors for gamma-ray true coincidence summing, and thermal neutron self-shielding effects were taken into account in this experiment by Monte Carlo simulations.

Silicon Nanowires with High-k Hafnium Oxide Dielectrics for Sensitive Detection of Small Nucleic Acid Oligomers

PubMed Central

Dorvel, Brian R.; Reddy, Bobby; Go, Jonghyun; Guevara, Carlos Duarte; Salm, Eric; Alam, Muhammad Ashraful; Bashir, Rashid

2012-01-01

Nanobiosensors based on silicon nanowire field effect transistors offer advantages of low cost, label-free detection, and potential for massive parallelization. As a result, these sensors have often been suggested as an attractive option for applications in Point-of-care (POC) medical diagnostics. Unfortunately, a number of performance issues such as gate leakage and current instability due to fluid contact, have prevented widespread adoption of the technology for routine use. High-k dielectrics, such as hafnium oxide (HfO2), have the known ability to address these challenges by passivating the exposed surfaces against destabilizing concerns of ion transport. With these fundamental stability issues addressed, a promising target for POC diagnostics and SiNWFET’s has been small oligonucleotides, more specifically microRNA (miRNA). MicroRNA’s are small RNA oligonucleotides which bind to messenger RNA’s, causing translational repression of proteins, gene silencing, and expressions are typically altered in several forms of cancer. In this paper, we describe a process for fabricating stable HfO2 dielectric based silicon nanowires for biosensing applications. Here we demonstrate sensing of single stranded DNA analogues to their microRNA cousins using miR-10b and miR-21 as templates, both known to be upregulated in breast cancer. We characterize the effect of surface functionalization on device performance using the miR-10b DNA analogue as the target sequence and different molecular weight poly-l-lysine as the functionalization layer. By optimizing the surface functionalization and fabrication protocol, we were able to achieve <100fM detection levels of miR-10b DNA analogue, with a theoretical limit of detection of 1fM. Moreover, the non-complementary DNA target strand, based on miR-21, showed very little response, indicating a highly sensitive and highly selective biosensing platform. PMID:22695179

Method for the melting of metals

DOEpatents

White, Jack C.; Traut, Davis E.

1992-01-01

A method of quantitatively determining the molten pool configuration in melting of metals. The method includes the steps of introducing hafnium metal seeds into a molten metal pool at intervals to form ingots, neutron activating the ingots and determining the hafnium location by radiometric means. Hafnium possesses exactly the proper metallurgical and radiochemical properties for this use.

6-Peroxo-6-zirconium crown and its hafnium analogue embedded in a triangular polyanion: [M6(O2)6(OH)6(gamma-SiW10O36)3]18- (M = Zr, Hf).

PubMed

Bassil, Bassem S; Mal, Sib Sankar; Dickman, Michael H; Kortz, Ulrich; Oelrich, Holger; Walder, Lorenz

2008-05-28

We have synthesized and structurally characterized the unprecedented peroxo-zirconium(IV) containing [Zr6(O2)6(OH)6(gamma-SiW10O36)3]18- (1). Polyanion 1 comprises a cyclic 6-peroxo-6-zirconium core stabilized by three decatungstosilicate units. We have also prepared the isostructural hafnium(IV) analogue [Hf6(O2)6(OH)6(gamma-SiW10O36)3]18- (2). We investigated the acid/base and redox properties of 1 by UV-vis spectroscopy and electrochemistry studies. Polyanion 1 represents the first structurally characterized Zr-peroxo POM with side-on, bridging peroxo units. The simple, one-pot synthesis of 1 and 2 involving dropwise addition of aqueous hydrogen peroxide could represent a general procedure for incorporating peroxo groups into a large variety of transition metal and lanthanide containing POMs.

40 CFR 471.91 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2010 CFR

2010-07-01

... million off-pounds) of zirconium-hafnium extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0... million off-pounds) of zirconium-hafnium heat treated Chromium 0.151 0.062 Cyanide 0.100 0.041 Nickel 0...-hafnium surface treated Chromium 0.150 0.61 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20...

40 CFR 471.91 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2011 CFR

2011-07-01

... million off-pounds) of zirconium-hafnium extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0... million off-pounds) of zirconium-hafnium heat treated Chromium 0.151 0.062 Cyanide 0.100 0.041 Nickel 0...-hafnium surface treated Chromium 0.150 0.61 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20...

A STUDY OF THE STABILITY OF ZIRCONIUM AND HAFNIUM TETRAHALIDES ON HITTING A HOT SURFACE IN VACUUM (in Russian)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tsirel'nikov, V.I.; Komissarova, L.N.; Spitsyn, V.I.

1962-09-01

The decomposition coefficients of the chlorides, bromides, and iodides of Zr and Hf were determined as a function of the temperature of a hot surface. The tetrahalides were carefully purified in an inert atmosphere of argon. The halide compound in a quartz ampoule was heated by a removable heater. The vapors passed through a capillary opening and struck a tungsten foil 0.5 mm thick and 12 to 15 mm wide. The Mo foil was heated electrically to control the surface temperature which was measured by an optical pyrometer. The tetrahalide decomposed according to the following reaction: Me(Hal)/sub 4/ yields Memore » + 2(Hal)/sub 2/. The lower halides dissociated completely to metal and free halides, since the temperature was >600 deg C. The Mo backing was dissolved in nitric acid, and the unsupported metal deposit of Zr or Hf was weighed, The decomposition coefficient was calcuweight of metal evaporated. Zrl/sub 4/ decomposed completely (100%) at 1500 deg C, while only 96% of the HfI/sub 4/ was decomposed at this temperature. The ZrBr/sub 4/ and HfBr/sub 4/ were decomposed by 68 and 61% respectively. The ZrCl/sub 4/ and HfCl/sub 4/ were stable at l500 deg C (5% of the ZrCl/sub 4/ was decomposed at l500 deg C). In all cases, the hafnium halide was more stable than the zirconium halide, especially in the case of the iodides. The decomposition was directly proportional to the temperature of the molybdenum target. (TTT)« less

Optimization of the Energy Level Alignment between the Photoactive Layer and the Cathode Contact Utilizing Solution-Processed Hafnium Acetylacetonate as Buffer Layer for Efficient Polymer Solar Cells.

PubMed

Yu, Lu; Li, Qiuxiang; Shi, Zhenzhen; Liu, Hao; Wang, Yaping; Wang, Fuzhi; Zhang, Bing; Dai, Songyuan; Lin, Jun; Tan, Zhan'ao

2016-01-13

The insertion of an appropriate interfacial buffer layer between the photoactive layer and the contact electrodes makes a great impact on the performance of polymer solar cells (PSCs). Ideal interfacial buffer layers could minimize the interfacial traps and the interfacial barriers caused by the incompatibility between the photoactive layer and the electrodes. In this work, we utilized solution-processed hafnium(IV) acetylacetonate (Hf(acac)4) as an effective cathode buffer layer (CBL) in PSCs to optimize the energy level alignment between the photoactive layer and the cathode contact, with the short-circuit current density (Jsc), open-circuit voltage (Voc), and fill factor (FF) all simultaneously improved with Hf(acac)4 CBL, leading to enhanced power conversion efficiencies (PCEs). Ultraviolet photoemission spectroscopy (UPS) and scanning Kelvin probe microscopy (SKPM) were performed to confirm that the interfacial dipoles were formed with the same orientation direction as the built-in potential between the photoactive layer and Hf(acac)4 CBL, benefiting the exciton separation and electron transport/extraction. In addition, the optical characteristics and surface morphology of the Hf(acac)4 CBL were also investigated.

Suppression of magnetic order in CaCo 1.86 As 2 with Fe substitution: Magnetization, neutron diffraction, and x-ray diffraction studies of Ca ( Co 1 – x Fe x ) y As 2

DOE PAGES

Jayasekara, W. T.; Pandey, Abhishek; Kreyssig, A.; ...

2017-02-23

Magnetization, neutron diffraction, and high-energy x-ray diffraction results for Sn-flux grown single-crystal samples of Ca(Co 1–xFe x) yAs 2, 0 ≤ x ≤ 1, 1.86 ≤ y ≤ 2, are presented and reveal that A-type antiferromagnetic order, with ordered moments lying along the c axis, persists for x ≲ 0.12(1). The antiferromagnetic order is smoothly suppressed with increasing x, with both the ordered moment and Néel temperature linearly decreasing. Stripe-type antiferromagnetic order does not occur for x ≤ 0.25, nor does ferromagnetic order for x up to at least x = 0.104, and a smooth crossover from the collapsed-tetragonal (cT)more » phase of CaCo 1.86As 2 to the tetragonal (T) phase of CaFe 2As 2 occurs. Furthermore, these results suggest that hole doping CaCo 1.86As 2 has a less dramatic effect on the magnetism and structure than steric effects due to substituting Sr for Ca.« less

Suppression of magnetic order in CaCo 1.86 As 2 with Fe substitution: Magnetization, neutron diffraction, and x-ray diffraction studies of Ca ( Co 1 – x Fe x ) y As 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jayasekara, W. T.; Pandey, Abhishek; Kreyssig, A.

Magnetization, neutron diffraction, and high-energy x-ray diffraction results for Sn-flux grown single-crystal samples of Ca(Co 1–xFe x) yAs 2, 0 ≤ x ≤ 1, 1.86 ≤ y ≤ 2, are presented and reveal that A-type antiferromagnetic order, with ordered moments lying along the c axis, persists for x ≲ 0.12(1). The antiferromagnetic order is smoothly suppressed with increasing x, with both the ordered moment and Néel temperature linearly decreasing. Stripe-type antiferromagnetic order does not occur for x ≤ 0.25, nor does ferromagnetic order for x up to at least x = 0.104, and a smooth crossover from the collapsed-tetragonal (cT)more » phase of CaCo 1.86As 2 to the tetragonal (T) phase of CaFe 2As 2 occurs. Furthermore, these results suggest that hole doping CaCo 1.86As 2 has a less dramatic effect on the magnetism and structure than steric effects due to substituting Sr for Ca.« less

Re-186 and Sm-153 dosimetry based on scintigraphic imaging data in skeletal metastasis palliative treatment and Monte Carlo simulation

NASA Astrophysics Data System (ADS)

Andreou, M.; Lagopati, N.; Lyra, M.

2011-09-01

Optimum treatment planning of patients suffering from painful skeletal metastases requires accurate calculations concerning absorbed dose in metastatic lesions and critical organs, such as red marrow. Delivering high doses to tumor cells while limiting radiation dose to normal tissue, is the key for successful palliation treatment. The aim of this study is to compare the dosimetric calculations, obtained by Monte Carlo (MC) simulation and the MIRDOSE model, in therapeutic schemes of skeleton metastatic lesions, with Rhenium-186 (Sn) -HEDP and Samarium-153 -EDTMP. A bolus injection of 1295 MBq (35mCi) Re-186- HEDP was infused in 11 patients with multiple skeletal metastases. The administered dose for the 8 patients who received Sm-153 was 1 mCi /kg. Planar scintigraphic images for the two groups of patients were obtained, 24 h, 48 h and 72 h post injection, by an Elscint Apex SPX gamma camera. The images were processed, utilizing ROI quantitative methods, to determine residence times and radionuclide uptakes. Dosimetric calculations were performed using the patient specific scintigraphic data by the MIRDOSE3 code of MIRD. Also, MCNPX was employed, simulating the distribution of the radioisotope in the ROI and calculating the absorbed doses in the metastatic lesion, and in critical organs. Summarizing, there is a good agreement between the results, derived from the two pathways, the patient specific and the mathematical, with a deviation of less than 9% for planar scintigraphic data compared to MC, for both radiopharmaceuticals.

Deep Resequencing of GWAS Loci Identifies Rare Variants in CARD9, IL23R and RNF186 That Are Associated with Ulcerative Colitis

PubMed Central

Boucher, Gabrielle; Lo, Ken Sin; Rivas, Manuel A.; Stevens, Christine; Alikashani, Azadeh; Ladouceur, Martin; Ellinghaus, David; Törkvist, Leif; Goel, Gautam; Lagacé, Caroline; Annese, Vito; Bitton, Alain; Begun, Jakob; Brant, Steve R.; Bresso, Francesca; Cho, Judy H.; Duerr, Richard H.; Halfvarson, Jonas; McGovern, Dermot P. B.; Radford-Smith, Graham; Schreiber, Stefan; Schumm, Philip L.; Sharma, Yashoda; Silverberg, Mark S.; Weersma, Rinse K.; D'Amato, Mauro; Vermeire, Severine; Franke, Andre; Lettre, Guillaume; Xavier, Ramnik J.; Daly, Mark J.; Rioux, John D.

2013-01-01

Genome-wide association studies and follow-up meta-analyses in Crohn's disease (CD) and ulcerative colitis (UC) have recently identified 163 disease-associated loci that meet genome-wide significance for these two inflammatory bowel diseases (IBD). These discoveries have already had a tremendous impact on our understanding of the genetic architecture of these diseases and have directed functional studies that have revealed some of the biological functions that are important to IBD (e.g. autophagy). Nonetheless, these loci can only explain a small proportion of disease variance (∼14% in CD and 7.5% in UC), suggesting that not only are additional loci to be found but that the known loci may contain high effect rare risk variants that have gone undetected by GWAS. To test this, we have used a targeted sequencing approach in 200 UC cases and 150 healthy controls (HC), all of French Canadian descent, to study 55 genes in regions associated with UC. We performed follow-up genotyping of 42 rare non-synonymous variants in independent case-control cohorts (totaling 14,435 UC cases and 20,204 HC). Our results confirmed significant association to rare non-synonymous coding variants in both IL23R and CARD9, previously identified from sequencing of CD loci, as well as identified a novel association in RNF186. With the exception of CARD9 (OR = 0.39), the rare non-synonymous variants identified were of moderate effect (OR = 1.49 for RNF186 and OR = 0.79 for IL23R). RNF186 encodes a protein with a RING domain having predicted E3 ubiquitin-protein ligase activity and two transmembrane domains. Importantly, the disease-coding variant is located in the ubiquitin ligase domain. Finally, our results suggest that rare variants in genes identified by genome-wide association in UC are unlikely to contribute significantly to the overall variance for the disease. Rather, these are expected to help focus functional studies of the corresponding disease loci. PMID:24068945

Effects of anode material on arcjet performance

NASA Technical Reports Server (NTRS)

Sankovic, John M.; Curran, Frank M.; Larson, C. A.

1992-01-01

Anodes fabricated from four different materials were tested in a modular arcjet thruster at 1 kW power level on nitrogen/hydrogen mixtures. A two-percent thoriated tungsten anode served as the control. Graphite was chosen for its ease in fabrication, but experienced severe erosion in the constrictor and diverging side. Hafnium carbide and lanthanum hexaboride were chosen for their low work functions but failed due to thermal stress and reacted with the propellant. When compared to the thoriated tungsten nozzle, thruster performance was significantly lower for the lanthanum hexaboride insert and the graphite nozzle, but was slightly higher for the hafnium carbide nozzle. Both the lanthanum hexaboride and hafnium carbide nozzle operated at higher voltages. An attempt was made to duplicate higher performance hafnium carbide results, but repeated attempts at machining a second anode insert were unsuccessful. Graphite, hafnium carbide, and lanthanum hexaboride do not appear viable anode materials for low power arcjet thrusters.

40 CFR 471.94 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2011 CFR

2011-07-01

...-hafnium extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0.301 Ammonia 31.6 13.9 Fluoride 14...-hafnium heat treated Chromium 0.015 0.006 Cyanide 0.010 0.004 Nickel 0.066 0.044 Ammonia 4.57 2.01...-hafnium surface treated Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20.0...

40 CFR 471.94 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2010 CFR

2010-07-01

...-hafnium extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0.301 Ammonia 31.6 13.9 Fluoride 14...-hafnium heat treated Chromium 0.015 0.006 Cyanide 0.010 0.004 Nickel 0.066 0.044 Ammonia 4.57 2.01...-hafnium surface treated Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20.0...

The solar photospheric abundance of hafnium and thorium. Results from CO5BOLD 3D hydrodynamic model atmospheres

NASA Astrophysics Data System (ADS)

Caffau, E.; Sbordone, L.; Ludwig, H.-G.; Bonifacio, P.; Steffen, M.; Behara, N. T.

2008-05-01

Context: The stable element hafnium (Hf) and the radioactive element thorium (Th) were recently suggested as a suitable pair for radioactive dating of stars. The applicability of this elemental pair needs to be established for stellar spectroscopy. Aims: We aim at a spectroscopic determination of the abundance of Hf and Th in the solar photosphere based on a CO5BOLD 3D hydrodynamical model atmosphere. We put this into a wider context by investigating 3D abundance corrections for a set of G- and F-type dwarfs. Methods: High-resolution, high signal-to-noise solar spectra were compared to line synthesis calculations performed on a solar CO5BOLD model. For the other atmospheres, we compared synthetic spectra of CO5BOLD 3D and associated 1D models. Results: For Hf we find a photospheric abundance A(Hf) = 0.87 ± 0.04, in good agreement with a previous analysis, based on 1D model atmospheres. The weak Th II 401.9 nm line constitutes the only Th abundance indicator available in the solar spectrum. It lies in the red wing of a Ni-Fe blend exhibiting a non-negligible convective asymmetry. Accounting for the asymmetry-related additional absorption, we obtain A(Th) = 0.08 ± 0.03, consistent with the meteoritic abundance, and about 0.1 dex lower than obtained in previous photospheric abundance determinations. Conclusions: Only for the second time, to our knowledge, has a non-negligible effect of convective line asymmetries on an abundance derivation been highlighted. Three-dimensional hydrodynamical simulations should be employed to measure Th abundances in dwarfs if similar blending is present, as in the solar case. In contrast, 3D effects on Hf abundances are small in G- to mid F-type dwarfs and sub-giants, and 1D model atmospheres can be conveniently used.

Corrosion resistant surface for vanadium nitride and hafnium nitride layers as function of grain size

NASA Astrophysics Data System (ADS)

Escobar, C. A.; Caicedo, J. C.; Aperador, W.

2014-01-01

In this research it was studied vanadium nitride (VN) and hafnium nitride (HfN) film, which were deposited onto silicon (Si (100)) and AISI 4140 steel substrates via r.f. magnetron sputtering technique in Ar/N2 atmosphere with purity at 99.99% for both V and Hf metallic targets. Both films were approximately 1.2±0.1 μm thick. The crystallography structures that were evaluated via X-ray diffraction analysis (XRD) showed preferential orientations in the Bragg planes VN (200) and HfN (111). The chemical compositions for both films were characterized by EDX. Atomic Force Microscopy (AFM) was used to study the morphology; the results reveal grain sizes of 78±2 nm for VN and 58±2 nm for HfN and roughness values of 4.2±0.1 nm for VN and 1.5±0.1 nm for HfN films. The electrochemical performance in VN and HfN films deposited onto steel 4140 were studied by Tafel polarization curves and impedance spectroscopy methods (EIS) under contact with sodium chloride at 3.5 wt% solution, therefore, it was found that the corrosion rate decreased about 95% in VN and 99% for HfN films in relation to uncoated 4140 steel, thus demonstrating, the protecting effect of VN and HfN films under a corrosive environment as function of morphological characteristics (grain size). VN(grain size)=78±2.0 nm, VN(roughness)=4.2±0.1 nm, VN(corrosion rate)=40.87 μmy. HfN(grain size)=58±2.0 nm, HfN(roughness)=1.5±0.1 nm, HfN(corrosion rate)=0.205 μmy. It was possible to analyze that films with larger grain size, can be observed smaller grain boundary thus generating a higher corrosion rate, therefore, in this work it was found that the HfN layer has better corrosion resistance (low corrosion rate) in relation to VN film which presents a larger grain size, indicating that the low grain boundary in (VN films) does not restrict movement of the Cl- ion and in this way the corrosion rate increases dramatically.

Os-186 and Os-187 Enrichments and High-He-3/He-4 sources in the Earth's Mantle: Evidence from Icelandic Picrites

NASA Technical Reports Server (NTRS)

Brandon, Alan D.; Graham, David W.; Waight, Tod; Gautason, Bjarni

2007-01-01

Picrites from the neovolcanic zones in Iceland display a range in Os-187/Os-188O from 0.1297 to 0.1381 ((gamma)Os = 0.0 to 6.5) and uniform Os-186/Os-188 of 0.1198375+/-32 (2 (sigma)). The value for Os-186/Os-188 is within uncertainty of the present-day value for the primitive upper mantle of 0.1198398+/-16. These Os isotope systematics are best explained by ancient recycled crust or melt enrichment in the mantle source region. If so, then the coupled enrichments displayed in Os-186/Os-188 and Os-187/Os-188 from lavas of other plume systems must result from an independent process, the most viable candidate at present remains core-mantle interaction. While some plumes with high He-3/He-4, such as Hawaii, appear to have been subjected to detectable addition of Os (and possibly He) from the outer core, others such as Iceland do not. A positive correlation between Os-187/Os-188 and He-3/He-4 from 9.6 to 19 RA in Iceland picrites is best modeled as mixtures of 500 Ma or older ancient recycled crust mixed with primitive mantle, creating a hybrid source region that subsequently mixes with the convecting MORB mantle during ascent and melting. This multistage mechanism to explain these isotope systematics is consistent with ancient recycled crust juxtaposed with more primitive, relatively He-rich mantle, in convective isolation from the upper mantle, most likely in the lowermost mantle. This is inconsistent with models that propose random mixing between heterogeneities in the convecting upper mantle as a mechanism to explain the observed isotopic variation in oceanic lavas or models that produce a high He-3/He-4 signature in melt depleted and strongly outgassed, He-poor mantle. Instead these systematics require a deep mantle source to explain the 3He/4He signature in Iceland lavas. The He-3/He-4 of lavas derived from the Iceland plume changed over time, from a maximum of 50 RA at 60 Ma, to approximately 25-27 RA at present. The changes are coupled with distinct

Raman Spectra of High-κ Dielectric Layers Investigated with Micro-Raman Spectroscopy Comparison with Silicon Dioxide

PubMed Central

Borowicz, P.; Taube, A.; Rzodkiewicz, W.; Latek, M.; Gierałtowska, S.

2013-01-01

Three samples with dielectric layers from high-κ dielectrics, hafnium oxide, gadolinium-silicon oxide, and lanthanum-lutetium oxide on silicon substrate were studied by Raman spectroscopy. The results obtained for high-κ dielectrics were compared with spectra recorded for silicon dioxide. Raman spectra suggest the similarity of gadolinium-silicon oxide and lanthanum-lutetium oxide to the bulk nondensified silicon dioxide. The temperature treatment of hafnium oxide shows the evolution of the structure of this material. Raman spectra recorded for as-deposited hafnium oxide are similar to the results obtained for silicon dioxide layer. After thermal treatment especially at higher temperatures (600°C and above), the structure of hafnium oxide becomes similar to the bulk non-densified silicon dioxide. PMID:24072982

Nuclear-grade zirconium prepared by combining combustion synthesis with molten-salt electrorefining technique

NASA Astrophysics Data System (ADS)

Li, Hui; Nersisyan, Hayk H.; Park, Kyung-Tae; Park, Sung-Bin; Kim, Jeong-Guk; Lee, Jeong-Min; Lee, Jong-Hyeon

2011-06-01

Zirconium has a low absorption cross-section for neutrons, which makes it an ideal material for use in nuclear reactor applications. However, hafnium typically contained in zirconium causes it to be far less useful for nuclear reactor materials because of its high neutron-absorbing properties. In the present study, a novel effective method has been developed for the production of hafnium-free zirconium. The process includes two main stages: magnesio-thermic reduction of ZrSiO 4 under a combustion mode, to produce zirconium silicide (ZrSi), and recovery of hafnium-free zirconium by molten-salt electrorefining. It was found that, depending on the electrorefining procedure, it is possible to produce zirconium powder with a low hafnium content: 70 ppm, determined by ICP-AES analysis.

[Radioprotection and environmental pollution by the use of the radionuclides 89Sr, 186Re, and 153Sm for pain palliation in metastatic bone diseases. Related calculations].

PubMed

Sbonias, Evangelos

2005-01-01

Due to the fact that the existing commercial analgesic drugs are not able to reduce effectively the pain caused by the metastatic bone disease, the use of radiopharmaceuticals with avidity to selectively localize in the metastatic skeletal sites, such as strondium-89 chloride (89Sr-Cl2), rhenium-186-hydroxy ethylene diphosphonate (186Re-HEDP), and samarium-153-ethylene diamine tetramethylene (153Sm-EDTMP), is widely accepted. However this medical application may be dangerous for the occupied personnel and more for general public, if radioactive waste is not properly disposed. In the following article we try to estimate the degree and the significance of that risk. For that reason we discuss the physical properties of these radionuclides and their distribution in the body of the patient. We conclude that 89Sr is not harmful for the physician, the attending personnel or those who live with the patient, because it radiates beta-radiation, while its gamma-radiation is negligeable. The radionuclides 186Re and 153Sm besides beta-radiation, also emit a perceptible amount of gamma-radiation. It has been shown that the exposure to gamma-radiation from these radionuclides of the physician, the attending personnel or those who live with the patient is very low as compared to the internationally accepted radioprotection limits. However the environmental contamination per treatment by either of these three radionuclides is not negligeable in comparison to the national and international accepted limits. Patients that are not in good clinical condition may pose an additional contamination danger to those attending them. For limiting radiocontamination, the annual number of treatments by the above three previous radionuclides, should be considered according to the ALARA principle in relation with the correct handling of these patients, and also considering the fundamentals of radioprotection.

Constraints on The Coupled Thermal Evolution of the Earth's Core and Mantle, The Age of The Inner Core, And The Origin of the 186Os/188Os Core(?) Signal in Plume-Derived Lavas

NASA Astrophysics Data System (ADS)

Lassiter, J. C.

2005-12-01

Thermal and chemical interaction between the core and mantle has played a critical role in the thermal and chemical evolution of the Earth's interior. Outer core convection is driven by core cooling and inner core crystallization. Core/mantle heat transfer also buffers mantle potential temperature, resulting in slower rates of mantle cooling (~50-100 K/Ga) than would be predicted from the discrepancy between current rates of surface heat loss (~44 TW) and internal radioactive heat production (~20 TW). Core/mantle heat transfer may also generate thermal mantle plumes responsible for ocean island volcanic chains such as the Hawaiian Islands. Several studies suggest that mantle plumes, in addition to transporting heat from the core/mantle boundary, also carry a chemical signature of core/mantle interaction. Elevated 186Os/188Os ratios in lavas from Hawaii, Gorgona, and in the 2.8 Ga Kostomuksha komatiites have been interpreted as reflecting incorporation of an outer core component with high time-integrated Pt/Os and Re/Os ( Brandon et al., 1999, 2003; Puchtel et al., 2005). Preferential partitioning of Os relative to Re and Pt into the inner core during inner core growth may generate elevated Re/Os and Pt/Os ratios in the residual outer core. Because of the long half-life of 190Pt (the parent of 186Os, t1/2 = 489 Ga), an elevated 186Os/188Os outer core signature in plume lavas requires that inner core crystallization began early in Earth history, most likely prior to 3.5 Ga. This in turn requires low time-averaged core/mantle heat flow (<~2.5 TW) or large quantities of heat-producing elements in the core. Core/mantle heat flow may be estimated using boundary-layer theory, by measuring the heat transported in mantle plumes, by estimating the heat transported along the outer core adiabat, or by comparing the rates of heat production, surface heat loss, and secular cooling of the mantle. All of these independent methods suggest time-averaged core/mantle heat flow of ~5

Technical Note: A simulation study on the feasibility of radiotherapy dose enhancement with calcium tungstate and hafnium oxide nano- and microparticles.

PubMed

Sherck, Nicholas J; Won, You-Yeon

2017-12-01

To assess the radiotherapy dose enhancement (RDE) potential of calcium tungstate (CaWO 4 ) and hafnium oxide (HfO 2 ) nano- and microparticles (NPs). A Monte Carlo simulation study was conducted to gauge their respective RDE potentials relative to that of the broadly studied gold (Au) NP. The study was warranted due to the promising clinical and preclinical studies involving both CaWO 4 and HfO 2 NPs as RDE agents in the treatment of various types of cancers. The study provides a baseline RDE to which future experimental RDE trends can be compared to. All three materials were investigated in silico with the software Penetration and Energy Loss of Positrons and Electrons (PENELOPE 2014) developed by Francesc Salvat and distributed in the United States by the Radiation Safety Information Computational Center (RSICC) at Oak Ridge National Laboratory. The work utilizes the extensively studied Au NP as the "gold standard" for a baseline. The key metric used in the evaluation of the materials was the local dose enhancement factor (DEF loc ). An additional metric used, termed the relative enhancement ratio (RER), evaluates material performance at the same mass concentrations. The results of the study indicate that Au has the strongest RDE potential using the DEF loc metric. HfO 2 and CaWO 4 both underperformed relative to Au with lower DEF loc of 2-3 × and 4-100 ×, respectively. The computational investigation predicts the RDE performance ranking to be: Au > HfO 2 > CaWO 4 . © 2017 American Association of Physicists in Medicine.

Investigation of electronic structure and magnetic properties of CaCo1.86As2 within the CPA method.

PubMed

Korotin, M A; Pchelkina, Z V; Skorikov, N A; Anisimov, V I; Shorikov, A O

2015-02-04

Recently in iron free arsenide compound CaCo(2)As(2) a 7(1)% of vacancies on the Co sites was detected (Quirinale D G et al 2013 Phys. Rev. B 88 174420). Here we report the investigation of electronic structure and magnetic properties of CaCo(1.86)As(2) within the coherent potential approximation (CPA). First, the CPA calculations are performed on the base of the local spin density approximation. Second, the possible role of Coulomb correlations is checked within the CPA scheme developed recently for strongly correlated systems. Then the spin-orbit coupling, which could be essential for Co, is also taken into account within the CPA calculation. The A type antiferromagnetic ground state and the value of magnetic moment obtained within the CPA approximation are in good agreement with experiment.

Growth, microstructure and electrical properties of sputter-deposited hafnium oxide (HfO2) thin films grown using HfO2 ceramic target

DOE Office of Scientific and Technical Information (OSTI.GOV)

Aguirre, B.; Vemuri, R. S.; Zubia, David

2011-01-01

Hafnium oxide (HfO₂) thin films have been made by radio-frequency (rf) magnetron-sputtering onto Si(100) substrates under varying growth temperature (Ts). HfO₂ ceramic target has been employed for sputtering while varying the Ts from room temperature to 500⁰C during deposition. The effect of Ts on the growth and microstructure of deposited HfO₂ films has been studied using grazing incidence x-ray diffraction (GIXRD), X-ray photoelectron spectroscopy (XPS), and high-resolution scanning electron microscopy (HR-SEM) coupled with energy dispersive x-ray spectrometry (EDS). The results indicate that the effect of Ts is significant on the growth, surface and interface structure, morphology and chemical composition ofmore » the HfO₂ films. Structural characterization indicates that the HfO₂ films grown at Ts<200 ⁰C are amorphous while films grown at Ts>200 ⁰C are nanocrystalline. An amorphous-to-crystalline transition occurs at Ts=200 ⁰C. Nanocrystalline HfO₂ films crystallized in a monoclinic structure with a (-111) orientation. XPS measurements indicated the high surface-chemical quality and stoichiometric nature of the grown HfO₂ films. An interface layer (IL) formation occurs due to reaction at the HfO₂-Si interface for HfO₂ films deposited at Ts>200 ⁰C. The thickness of IL increases with increasing Ts. XPS and EDS at the HfO₂-Si cross-section indicate the IL is a (Hf, Si)-O compound. The electrical characterization using capacitance-voltage measurements indicate that the dielectric constant decreases from 25 to 16 with increasing Ts.« less

Transition metal complexes supported on metal-organic frameworks for heterogeneous catalysts

DOEpatents

Farha, Omar K.; Hupp, Joseph T.; Delferro, Massimiliano; Klet, Rachel C.

2017-02-07

A robust mesoporous metal-organic framework comprising a hafnium-based metal-organic framework and a single-site zirconium-benzyl species is provided. The hafnium, zirconium-benzyl metal-organic framework is useful as a catalyst for the polymerization of an alkene.

CVD aluminiding process for producing a modified platinum aluminide bond coat for improved high temperature performance

NASA Technical Reports Server (NTRS)

Nagaraj, Bangalore A. (Inventor); Williams, Jeffrey L. (Inventor)

2003-01-01

A method of depositing by chemical vapor deposition a modified platinum aluminide diffusion coating onto a superalloy substrate comprising the steps of applying a layer of a platinum group metal to the superalloy substrate; passing an externally generated aluminum halide gas through an internal gas generator which is integral with a retort, the internal gas generator generating a modified halide gas; and co-depositing aluminum and modifier onto the superalloy substrate. In one form, the modified halide gas is hafnium chloride and the modifier is hafnium with the modified platinum aluminum bond coat comprising a single phase additive layer of platinum aluminide with at least about 0.5 percent hafnium by weight percent and about 1 to about 15 weight percent of hafnium in the boundary between a diffusion layer and the additive layer. The bond coat produced by this method is also claimed.

Method for fabricating hafnia films

DOEpatents

Hu, Michael Z [Knoxville, TN

2007-08-21

The present invention comprises a method for fabricating hafnia film comprising the steps of providing a substrate having a surface that allows formation of a self-assembled monolayer thereon via covalent bonding; providing an aqueous solution that provides homogeneous hafnium ionic complexes and hafnium nanoclusters wherein the aqueous solution is capable of undergoing homogeneous precipitation under controlled conditions for a desired period of time at a controlled temperature and controlled solution acidity for desired nanocluster nucleation and growth kinetics, desired nanocluster size, desired growth rate of film thickness and desired film surface characteristics. The method further comprising forming the self-assembled monolayer on the surface of the substrate wherein the self-assembled monolayer comprises a plurality of hydrocarbon chains cross-linked together along the surface of the substrate, the hydrocarbon chains being uniformly spaced from one another and wherein each of the hydrocarbon chains having a functional anchoring group at a first end of the chain covalently bonded with the surface of the substrate and each of the hydrocarbon chains having a functional terminating group projected away from the surface wherein the functional terminating group provides a bonding site for the hafnium film to grow; and exposing the substrate to the aqueous solution for a desired period of time at a controlled temperature wherein the hafnium ionic complexes and the hafnium nanoclusters are deposited on the bonding site of the functional terminating group thereby forming the hafnia film wherein the hafnium bonded to the hydrocarbons and to one another provide a uniform ordered arrangement defined by the uniform arrangement of the hydrocarbons.

PRODUCTION OF METALS AND THEIR COMPOUNDS

DOEpatents

Arden, T.V.; Burstall, F.H.; Davies, G.R.; Linstead, R.P.; Wells, R.A.

1958-11-18

Zirconium nitrate can be separated from hafnium nitrate by mixing the nitrates with ethyl cellulose pulp, eluting the mass with diethyl ether containing nitric acid, and passing the eluent through a column of cellulose pulp the outflow of which is substantially free of hafnium.

Effects of alloy composition in alleviating embrittlement problems associated with the tantalum alloy T-111

NASA Technical Reports Server (NTRS)

Stephens, J. R.

1975-01-01

The causes of aging embrittlement in T-111 (Ta-8W-2Hf) and the effect of alloy modification were investigated. Results show that T-111 possesses a critical combination of tungsten and hafnium that leads to loss in ductility at -196 C after aging near 1040 C. It was found that this occurs because tungsten enhances hafnium segregation to grain boundaries, which also leads to increased susceptibility to hydrogen embrittlement. Aging embrittlement was not observed in tantalum alloys with reduced tungsten or hafnium contents; most of the alloys studied have lower strengths than T-111 and exhibit susceptibility to hydrogen embrittlement.

Composition and method for brazing graphite to graphite

DOEpatents

Taylor, Albert J.; Dykes, Norman L.

1984-01-01

The present invention is directed to a brazing material for joining graphite structures that can be used at temperatures up to about 2800.degree. C. The brazing material formed of a paste-like composition of hafnium carbide and uranium oxide with a thermosetting resin. The uranium oxide is converted to uranium dicarbide during the brazing operation and then the hafnium carbide and uranium dicarbide form a liquid phase at a temperature about 2600.degree. C. with the uranium diffusing and vaporizing from the joint area as the temperature is increased to about 2800.degree. C. so as to provide a brazed joint consisting essentially of hafnium carbide. This brazing temperature for hafnium carbide is considerably less than the eutectic temperature of hafnium carbide of about 3150.degree. C. The brazing composition also incorporates the thermosetting resin so that during the brazing operation the graphite structures may be temporarily bonded together by thermosetting the resin so that machining of the structures to final dimensions may be completed prior to the completion of the brazing operation. The resulting brazed joint is chemically and thermally compatible with the graphite structures joined thereby and also provides a joint of sufficient integrity so as to at least correspond with the strength and other properties of the graphite.

Platinum and palladium incorporation into phosphate/viologen-phosphonates of zirconium and hafnium: synthesis and characterization

NASA Astrophysics Data System (ADS)

Dokoutchaev, Alexandre; Krishnan, Venkatesan V.; Thompson, Mark E.; Balasubramanian, Mahalingam

1998-10-01

We have continued previous efforts to synthesize and characterize a microporous metal phosphate/viologen-phosphonate compound, [(ZrF) 2(PO 4)(O 3PCH 2CH 2-4,4'-bipyridinium-CH 2CH 2PO 3)] ṡF·2H 2O, ZrPO PV. A derivative of this material has been shown to be an efficient catalyst for the production of hydrogen peroxide from hydrogen and oxygen. This paper has two objectives—one is to optimize the synthetic routes leading to the preparation of MPO PV (M=zirconium or hafnium) and the second is to characterize MPO PV and the derivatives formed by Pt or Pd incorporation by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray powder diffraction (XRD), inductively coupled plasma-mass spectrometry (ICP-MS) and X-ray absorption fine structure analysis (XAFS). Powder XRD data have shown much higher crystallinity in MPO PV samples prepared by hydrothermal methods than those prepared by reflux methods. In the hydrothermal synthesis, the amount of mineralizer (HF) present controlled the crystallite size (as determined from TEM micrographs). The larger the quantity of HF in the bomb, the larger the size of the crystals but the lower the yield of the MPO PV material. Crystal sizes of about 2.5 μm in length and 0.15 μm in diameter have been made with very large quantities of HF as mineralizer (10 times the required stoichiometric amount). Ion exchange of the material by PdCl 42- has resulted in the incorporation of the PdCl 42- ions in place of X - in the material. This has been confirmed by XAFS studies that demonstrate the oxidation state of Pd is 2+ and show four Cl atoms bound to Pd. Upon reduction it has been confirmed (by XAFS) that the palladium exists as metal with oxidation state of zero. Ion exchange by PdCl 42- and PtCl 42- and subsequent reduction of the material suspension by hydrogen result in the formation of separate Pt and Pd colloids in the close vicinity of the crystallites. TEM micrographs show clearly that the Pt metal

Regulation of salt marsh mosquito populations by the 18.6-yr lunar-nodal cycle.

PubMed

Rochlin, Ilia; Morris, James T

2017-08-01

The 18.6-yr lunar-nodal cycle drives changes in tidal amplitude globally, affecting coastal habitat formation, species and communities inhabiting rocky shores, and salt marsh vegetation. However, the cycle's influence on salt marsh fauna lacked sufficient long-term data for testing its effect. We circumvented this problem by using salt marsh mosquito records obtained over a period of over four decades in two estuaries in the northeastern USA. Salt marsh mosquito habitat is near the highest tide level where the impact of the nodal cycle on flood frequency is greatest. Wavelet spectral and cross-correlation analyses revealed periodicity in salt marsh mosquito abundance that was negatively correlated with tidal amplitude. Tidal amplitude was a significant predictor of salt marsh mosquito abundance with the cycle maxima coinciding with lower mosquito populations, possibly due to access by predatory fish. However, these effects were detected only at the location with extensive salt marsh habitat and astronomical tides and were weakened or lacked significance at the location with small microtidal salt marshes and wind-driven tides. Mosquitoes can serve as proxy indicators for numerous invertebrate species on the salt marsh. These predictable cycles and their effects need to be taken into consideration when investigating, restoring, or managing intertidal communities that are also facing sea-level rise. © 2017 by the Ecological Society of America.

Re-187-Os-187, Pt-190-Os-186 Isotopic and Highly Siderophile Element Systematics of Group IVA Irons

NASA Technical Reports Server (NTRS)

Walker, R. J.; McCoy, T. J.; Schulte, R. F.; McDonough, W. F.; Ash, R. D.

2005-01-01

We have recently completed Re-187-Os-187 and Pt-190-Os-186 isotopic and elemental studies of the two largest magmatic iron meteorite groups, IIAB and IIIAB [1]. These studies revealed closed-system behavior of both isotopic systems, but complex trace element behavior for Re, Pt and Os in group IIIAB. Here we examine isotopic and trace elemental systematics of group IVA irons. The IVA irons are not as extensively fractionated as IIAB and IIIAB and their apparently less complex crystallization history may make for more robust interpretation of the relative partitioning behavior of Re, Pt and Os, as well as the other highly siderophile elements (HSE) measured here; Pd, Ru and Ir [e.g. 2]. An additional goal of our continuing research plan for iron meteorites is to assess the possibility of relating certain ungrouped irons with major groups via trace element modeling. Here, the isotopic and trace element systematics of the ungrouped irons Nedagolla and EET 83230 are compared with the IVA irons.

Constraints on the coupled thermal evolution of the Earth's core and mantle, the age of the inner core, and the origin of the 186Os/188Os “core signal” in plume-derived lavas

NASA Astrophysics Data System (ADS)

Lassiter, J. C.

2006-10-01

The possibility that some mantle plumes may carry a geochemical signature of core/mantle interaction has rightly generated considerable interest and attention in recent years. Correlated 186Os- 187Os enrichments in some plume-derived lavas (Hawaii, Gorgona, Kostomuksha) have been interpreted as deriving from an outer core with elevated Pt/Os and Re/Os ratios due to the solidification of the Earth's inner core (c.f., [A.D. Brandon, R.J. Walker, The debate over core-mantle interaction, Earth Planet. Sci. Lett. 232 (2005) 211-225.] and references therein). Conclusive identification of a "core signal" in plume-derived lavas would profoundly influence our understanding of mantle convection and evolution. This paper reevaluates the Os-isotope evidence for core/mantle interaction by examining other geochemical constraints on core/mantle interaction, geophysical constraints on the thermal evolution of the outer core, and geochemical and cosmochemical constraints on the abundance of heat-producing elements in the core. Additional study of metal/silicate and sulfide/silicate partitioning of K, Pb, and other trace elements is needed to more tightly constrain the likely starting composition of the Earth's core. However, available data suggest that the observed 186Os enrichments in Hawaiian and other plume-derived lavas are unlikely to derive from core/mantle interaction. 1) Core/mantle interaction sufficient to produce the observed 186Os enrichments would likely have significant effects on other tracers such as Pb- and W-isotopes that are not observed. 2) Significant partitioning of K or other heat-producing elements into the core would produce a "core depletion" pattern in the Silicate Earth very different from that observed. 3) In the absence of heat-producing elements in the core, core/mantle heat flow of ˜ 6-15 TW estimated from several independent geophysical constraints suggests an inner core age (< ˜ 2.5 Ga) too young for the outer core to have developed a significant

Probing the remarkable thermal kinetics of visual rhodopsin with E181Q and S186A mutants

NASA Astrophysics Data System (ADS)

Guo, Ying; Hendrickson, Heidi P.; Videla, Pablo E.; Chen, Ya-Na; Ho, Junming; Sekharan, Sivakumar; Batista, Victor S.; Tully, John C.; Yan, Elsa C. Y.

2017-06-01

We recently reported a very unusual temperature dependence of the rate of thermal reaction of wild type bovine rhodopsin: the Arrhenius plot exhibits a sharp "elbow" at 47 °C and, in the upper temperature range, an unexpectedly large activation energy (114 ± 8 kcal/mol) and an enormous prefactor (1072±5 s-1). In this report, we present new measurements and a theoretical model that establish convincingly that this behavior results from a collective, entropy-driven breakup of the rigid hydrogen bonding networks (HBNs) that hinder the reaction at lower temperatures. For E181Q and S186A, two rhodopsin mutants that disrupt the HBNs near the binding pocket of the 11-cis retinyl chromophore, we observe significant decreases in the activation energy (˜90 kcal/mol) and prefactor (˜1060 s-1), consistent with the conclusion that the reaction rate is enhanced by breakup of the HBN. The results provide insights into the molecular mechanism of dim-light vision and eye diseases caused by inherited mutations in the rhodopsin gene that perturb the HBNs.

Grindability of cast Ti-Hf alloys.

PubMed

Kikuchi, Masafumi; Takahashi, Masatoshi; Sato, Hideki; Okuno, Osamu; Nunn, Martha E; Okabe, Toru

2006-04-01

As part of our systematic studies characterizing the properties of titanium alloys, we investigated the grindability of a series of cast Ti-Hf alloys. Alloy buttons with hafnium concentrations up to 40 mass% were made using an argon-arc melting furnace. Each button was cast into a magnesia-based mold using a dental titanium casting machine; three specimens were made for each metal. Prior to testing, the hardened surface layer was removed. The specimens were ground at five different speeds for 1 min at 0.98 N using a carborundum wheel on an electric dental handpiece. Grindability was evaluated as the volume of metal removed per minute (grinding rate) and the volume ratio of metal removed compared to the wheel material lost (grinding ratio). The data were analyzed using ANOVA. A trend of increasing grindability was found with increasing amounts of hafnium, although there was no statistical difference in the grindability with increasing hafnium contents. We also found that hafnium may be used to harden or strengthen titanium without deteriorating the grindability.

Composition and method for brazing graphite to graphite

DOEpatents

Taylor, A.J.; Dykes, N.L.

1982-08-10

A brazing material is described for joining graphite structures that can be used up to 2800/sup 0/C. The brazing material is formed of a paste-like composition of hafnium carbide and uranium oxide with a thermosetting resin. The uranium oxide is converted to uranium dicarbide during the brazing operation and then the hafnium carbide and uranium dicarbide form a liquid phase at a temperature about 2600/sup 0/C with the uranium diffusing and vaporizing from the joint area as the temperature is increased to about 2800/sup 0/C so as to provide a brazed joint consisting essentially of hafnium carbide. The resulting brazed joint is chemically and thermally compatible with the graphite structures.

Studies of Ultra High Temperature Ceramic Composite Components: Synthesis and Characterization of HfOxCy and Si Oxidation in Atomic Oxygen Containing Environments

DTIC Science & Technology

2008-08-01

Andrea Hafeman and Dr Scott Guelcher for the use of the SDT analysis software. I would like to thank my committee members: Dr Clare McCabe, Dr Sharon...76 4.2: Thermogravimetric curves obtained during oxidation of hafnium...77 4.3: The thermogravimetric curves for hafnia and hafnium oxycarbide (28 mTorr) oxidized at 600°C

A high stellar velocity dispersion for a compact massive galaxy at redshift z = 2.186.

PubMed

van Dokkum, Pieter G; Kriek, Mariska; Franx, Marijn

2009-08-06

Recent studies have found that the oldest and most luminous galaxies in the early Universe are surprisingly compact, having stellar masses similar to present-day elliptical galaxies but much smaller sizes. This finding has attracted considerable attention, as it suggests that massive galaxies have grown in size by a factor of about five over the past ten billion years (10 Gyr). A key test of these results is a determination of the stellar kinematics of one of the compact galaxies: if the sizes of these objects are as extreme as has been claimed, their stars are expected to have much higher velocities than those in present-day galaxies of the same mass. Here we report a measurement of the stellar velocity dispersion of a massive compact galaxy at redshift z = 2.186, corresponding to a look-back time of 10.7 Gyr. The velocity dispersion is very high at km s(-1), consistent with the mass and compactness of the galaxy inferred from photometric data. This would indicate significant recent structural and dynamical evolution of massive galaxies over the past 10 Gyr. The uncertainty in the dispersion was determined from simulations that include the effects of noise and template mismatch. However, we cannot exclude the possibility that some subtle systematic effect may have influenced the analysis, given the low signal-to-noise ratio of our spectrum.

Interfacial phenomena in high-kappa dielectrics

NASA Astrophysics Data System (ADS)

Mathew, Anoop

The introduction of novel high-kappa dielectric materials to replace the traditional SiO2 insulating layer in CMOS transistors is a watershed event in the history of transistor development. Further, replacement of the traditional highly-doped polycrystalline silicon gate electrode with a new set of materials for metal gates complicates the transition and introduces further integration challenges. A whole variety of new material surfaces and interfaces are thus introduced that merit close investigation to determine parameters for optimal device performance. Nitrogen is a key component that improves the performance of a variety of materials for the next generation of these CMOS transistors. Nitrogen is introduced into new gate dielectric materials such as hafnium silicates as well as in potential metal gate materials such as hafnium nitride. A photoemission study of the binding energies of the various atoms in these systems using photoemission reveals the nature of the atomic bonding. The current study compares hafnium silicates of various compositions which were thermally nitrided at different temperatures in ammonia, hafnium nitrides, and thin HfO2 films using photoelectron spectroscopy. A recurring theme that is explored is the competition between oxygen and nitrogen atoms in bonding with hafnium and other atoms. The N 1s photoemission peak is seen to have contributions from its bonding with hafnium, oxygen, and silicon atoms. The Hf 4f and O 1s spectra similarly exhibit signatures of their bonding environment with their neighboring atoms. Angle resolved photoemission and in-situ annealing/argon sputtering experiments are used to elucidate the nature of the bonding and its evolution with processing. A nondestructive profilitng of nitrogen distribution as a function of composition in nitrided hafnium silicates is also constructed using angle resolved photoemission as a function of the take-off angle. These results are corroborated with depth reconstruction obtained

40 CFR 471.93 - New source performance standards (NSPS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... monthly average mg/off-kg (pounds per million off-pounds) of zirconium-hafnium extruded Chromium 0.104 0... monthly average mg/off-kg (pounds per million off-pounds) of zirconium-hafnium heat treated Chromium 0.015... Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20.0 Fluoride 20.0 8.98 Oil and...

40 CFR 471.93 - New source performance standards (NSPS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... monthly average mg/off-kg (pounds per million off-pounds) of zirconium-hafnium extruded Chromium 0.104 0... monthly average mg/off-kg (pounds per million off-pounds) of zirconium-hafnium heat treated Chromium 0.015... Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20.0 Fluoride 20.0 8.98 Oil and...

Radioisotopic heat source

DOEpatents

Jones, G.J.; Selle, J.E.; Teaney, P.E.

1975-09-30

Disclosed is a radioisotopic heat source and method for a long life electrical generator. The source includes plutonium dioxide shards and yttrium or hafnium in a container of tantalum-tungsten-hafnium alloy, all being in a nickel alloy outer container, and subjected to heat treatment of from about 1570$sup 0$F to about 1720$sup 0$F for about one h. (auth)

Enhancement of thermoelectric figure-of-merit at low temperatures by titanium substitution for hafnium in n-type half-Heuslers Hf0.75-xTixZr0.25NiSn0.99Sb0.01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Giri; Dahal, Tulashi; Chen, Shuo

The effect of titanium (Ti) substitution for hafnium (Hf) on thermoelectric properties of (Hf, Zr)-based n-type half-Heuslers: Hf0.75-xTixZr0.25NiSn0.99Sb0.01, has been studied. The samples are made by arc melting followed by ball milling and hot pressing via the nanostructuring approach. A peak thermoelectric figure-of-merit (ZT) of ~1.0 is achieved at 500 °C in samples with a composition of Hf0.5Zr0.25Ti0.25NiSn0.99Sb0.01 due to a slight increase in carrier concentration and also a lower thermal conductivity caused by Ti. The ZT values below 500 °C of hot pressed Hf0.5Zr0.25Ti0.25NiSn0.99Sb0.01 samples are significantly higher than those of the same way prepared Hf0.75Zr0.25NiSn0.99Sb0.01 samples at eachmore » temperature, which are very much desired for mid-range temperature applications such as waste heat recovery in automobiles.« less

Enhancement of thermoelectric figure-of-merit at low temperatures by titanium substitution for hafnium in n-type half-Heuslers Hf0.75-xTixZr0.25NiSn0.99Sb0.01

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joshi, Giri; Dahal, Tulashi; Chen, Shuo

The effect of titanium (Ti) substitution for hafnium (Hf) on thermoelectric properties of (Hf, Zr)-based n-type half-Heuslers: Hf 0.75-xTi xZr 0.25NiSn 0.99Sb 0.01, has been studied. The samples are made by arc melting followed by ball milling and hot pressing via the nanostructuring approach. A peak thermoelectric figure-of-merit (ZT) of ~1.0 is achieved at 500 °C in samples with a composition of Hf 0.5Zr 0.25Ti 0.25NiSn 0.99Sb 0.01 due to a slight increase in carrier concentration and also a lower thermal conductivity caused by Ti. TheZT values below 500 °C of hot pressed Hf 0.5Zr 0.25Ti 0.25NiSn 0.99Sb 0.01 samplesmore » are significantly higher than those of the same way prepared Hf 0.75Zr 0.25NiSn 0.99Sb 0.01samples at each temperature, which are very much desired for mid-range temperature applications such as waste heat recovery in automobiles.« less

Evolution of E 2 transition strength in deformed hafnium isotopes from new measurements on 172Hf,174Hf, and 176Hf

NASA Astrophysics Data System (ADS)

Rudigier, M.; Nomura, K.; Dannhoff, M.; Gerst, R.-B.; Jolie, J.; Saed-Samii, N.; Stegemann, S.; Régis, J.-M.; Robledo, L. M.; Rodríguez-Guzmán, R.; Blazhev, A.; Fransen, Ch.; Warr, N.; Zell, K. O.

2015-04-01

Background: The available data for E 2 transition strengths in the region between neutron-deficient hafnium and platinum isotopes are far from complete. More and precise data are needed to enhance the picture of structure evolution in this region and to test state-of-the-art nuclear models. In a simple model, the maximum collectivity is expected at the middle of the major shell. However, for actual nuclei, particularly in heavy-mass regions, which should be highly complex, this picture may no longer be the case, and one should use a more realistic nuclear-structure model. We address this point by studying the spectroscopy of Hf as a representative case. Purpose: We remeasure the 21+ half-lives of 172,174,176Hf, for which there is some disagreement in the literature. The main goal is to measure, for the first time, the half-lives of higher-lying states of the rotational band. The new results are compared to a theoretical calculation for absolute transition strengths. Method: The half-lives were measured using γ -γ and conversion-electron-γ delayed coincidences with the fast timing method. For the determination of half-lives in the picosecond region, the generalized centroid difference method was applied. For the theoretical calculation of the spectroscopic properties, the interacting boson model is employed, whose Hamiltonian is determined based on microscopic energy-density functional calculations. Results: The measured 21+ half-lives disagree with results from earlier γ -γ fast timing measurements, but are in agreement with data from Coulomb excitation experiments and other methods. Half-lives of the 41+ and 61+ states were measured, as well as a lower limit for the 81+ states. Conclusions: This work shows the importance of a mass-dependent effective boson charge in the interacting boson model for the description of E 2 transition rates in chains of nuclei. It encourages further studies of the microscopic origin of this mass dependence. New experimental

Anti-phytopathogen potential of endophytic actinobacteria isolated from tomato plants (Lycopersicon esculentum) in southern Brazil, and characterization of Streptomyces sp. R18(6), a potential biocontrol agent.

PubMed

de Oliveira, Margaroni Fialho; da Silva, Mariana Germano; Van Der Sand, Sueli T

2010-09-01

Tomato plants (Lycopersicon esculentum) are highly susceptible to phytopathogen attack. The resulting intensive application of pesticides on tomato crops can affect the environment and health of humans and animals. The objective of this study was to select potential biocontrol agents among actinobacteria from tomato plants, in a search for alternative phytopathogen control. We evaluated 70 endophytic actinobacteria isolated from tomato plants in southern Brazil, testing their antimicrobial activity, siderophore production, indoleacetic acid production, and phosphate solubility. The actinomycete isolate with the highest antimicrobial potential was selected using the agar-well diffusion method, in order to optimize conditions for the production of compounds with antimicrobial activity. For this study, six growth media (starch casein-SC, ISP2, Bennett's, Sahin, Czapek-Dox, and TSB), three temperatures (25 degrees C, 30 degrees C, and 35 degrees C) and different pH were tested. Of the actinobacteria tested, 88.6% showed antimicrobial activity against at least one phytopathogen, 72.1% showed a positive reaction for indoleacetic acid production, 86.8% produced siderophores and 16.2% showed a positive reaction for phosphate solubility. Isolate R18(6) was selected due to its antagonistic activity against all phytopathogenic microorganisms tested in this study. The best conditions for production were observed in the SC medium, at 30 degrees C and pH 7.0. The isolate R18(6) showed close biochemical and genetic similarity to Streptomyces pluricolorescens. Copyright 2010 Elsevier Masson SAS. All rights reserved.

Ceramic material suitable for repair of a space vehicle component in a microgravity and vacuum environment, method of making same, and method of repairing a space vehicle component

NASA Technical Reports Server (NTRS)

Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

2009-01-01

A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium diboride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

Methods of repairing a substrate

NASA Technical Reports Server (NTRS)

Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

2011-01-01

A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium boride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

Structure of glutathione reductase from Escherichia coli at 1.86 A resolution: comparison with the enzyme from human erythrocytes.

PubMed Central

Mittl, P. R.; Schulz, G. E.

1994-01-01

The crystal structure of the dimeric flavoenzyme glutathione reductase from Escherichia coli was determined and refined to an R-factor of 16.8% at 1.86 A resolution. The molecular 2-fold axis of the dimer is local but very close to a possible crystallographic 2-fold axis; the slight asymmetry could be rationalized from the packing contacts. The 2 crystallographically independent subunits of the dimer are virtually identical, yielding no structural clue on possible cooperativity. The structure was compared with the well-known structure of the homologous enzyme from human erythrocytes with 52% sequence identity. Significant differences were found at the dimer interface, where the human enzyme has a disulfide bridge, whereas the E. coli enzyme has an antiparallel beta-sheet connecting the subunits. The differences at the glutathione binding site and in particular a deformation caused by a Leu-Ile exchange indicate why the E. coli enzyme accepts trypanothione much better than the human enzyme. The reported structure provides a frame for explaining numerous published engineering results in detail and for guiding further ones. PMID:8061609

40 CFR 471.95 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2011 CFR

2011-07-01

... extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0.301 Ammonia 31.6 13.9 Fluoride 14.1 6.26...-hafnium heat treated Chromium 0.015 0.006 Cyanide 0.010 0.004 Nickel 0.066 0.044 Ammonia 4.57 2.01...-hafnium surface treated Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20...

40 CFR 471.95 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2010 CFR

2010-07-01

... extruded Chromium 0.104 0.043 Cyanide 0.069 0.029 Nickel 0.455 0.301 Ammonia 31.6 13.9 Fluoride 14.1 6.26...-hafnium heat treated Chromium 0.015 0.006 Cyanide 0.010 0.004 Nickel 0.066 0.044 Ammonia 4.57 2.01...-hafnium surface treated Chromium 0.150 0.061 Cyanide 0.099 0.041 Nickel 0.653 0.432 Ammonia 45.3 20...

Precipitation hardening austenitic superalloys

DOEpatents

Korenko, Michael K.

1985-01-01

Precipitation hardening, austenitic type superalloys are described. These alloys contain 0.5 to 1.5 weight percent silicon in combination with about 0.05 to 0.5 weight percent of a post irradiation ductility enhancing agent selected from the group of hafnium, yttrium, lanthanum and scandium, alone or in combination with each other. In addition, when hafnium or yttrium are selected, reductions in irradiation induced swelling have been noted.

Investigation of gamma radiation induced changes in local structure of borosilicate glass by TDPAC and EXAFS

NASA Astrophysics Data System (ADS)

Kumar, Ashwani; Nayak, C.; Rajput, P.; Mishra, R. K.; Bhattacharyya, D.; Kaushik, C. P.; Tomar, B. S.

2016-12-01

Gamma radiation induced changes in local structure around the probe atom (Hafnium) were investigated in sodium barium borosilicate (NBS) glass, used for immobilization of high level liquid waste generated from the reprocessing plant at Trombay, Mumbai. The (NBS) glass was doped with 181Hf as a probe for time differential perturbed angular correlation (TDPAC) spectroscopy studies, while for studies using extended X-ray absorption fine structure (EXAFS) spectroscopy, the same was doped with 0.5 and 2 % (mole %) hafnium oxide. The irradiated as well as un-irradiated glass samples were studied by TDPAC and EXAFS techniques to obtain information about the changes (if any) around the probe atom due to gamma irradiation. TDPAC spectra of unirradiated and irradiated glasses were similar and reminescent of amorphous materials, indicating negligible effect of gamma radiation on the microstructure around Hafnium probe atom, though the quaqdrupole interaction frequency ( ω Q) and asymmetry parameter ( η) did show a marginal decrease in the irradiated glass compared to that in the unirradiated glass. EXAFS measurements showed a slight decrease in the Hf-O bond distance upon gamma irradiation of Hf doped NBS glass indicating densification of the glass matrix, while the cordination number around hafnium remains unchanged.

Synthesis of transparent nanocomposite monoliths for gamma scintillation

NASA Astrophysics Data System (ADS)

Liu, Chao; Hajagos, Tibor J.; Kishpaugh, David; Jin, Yunxia; Hu, Wei; Chen, Qi; Pei, Qibing

2015-08-01

During the past decade, inorganic nanoparticles/polymer nanocomposites have been intensively studied to provide a low cost, high performance alternative for gamma scintillation. However, the aggregation of nanoparticles often occurs even at low nanoparticle concentrations and thus deteriorates the transparency and performance of these nanocomposite scintillators. Here we report an efficient fabrication protocol of transparent nanocomposite monoliths based on surface modified hafnium oxide nanoparticles. Using hafnium oxide nanoparticles with surface-grafted methacrylate groups, highly transparent bulk-size nanocomposite monoliths (2 mm thick, transmittance at 550 nm >75%) are fabricated with nanoparticle loadings up to 40 wt% (net hafnium wt% up to 28.5%). These nanocomposite monoliths of 1 cm diameter and 2 mm thickness are capable of producing a full energy photopeak for 662 keV gamma rays, with the best deconvoluted photopeak energy resolution reaching 8%.

Ternary boride product and process

NASA Technical Reports Server (NTRS)

Clougherty, Edward V. (Inventor)

1976-01-01

A hard, tough, strong ceramic body is formed by hot pressing a mixture of a powdered metal and a powdered metal diboride. The metal employed is zirconium, titanium or hafnium and the diboride is the diboride of a different member of the same group of zirconium, titanium or hafnium to form a ternary composition. During hot pressing at temperatures above about 2,000.degree.F., a substantial proportion of acicular ternary monoboride is formed.

Lowering the environmental impact of high-kappa/ metal gate stack surface preparation processes

NASA Astrophysics Data System (ADS)

Zamani, Davoud

ABSTRACT Hafnium based oxides and silicates are promising high-κ dielectrics to replace SiO2 as gate material for state-of-the-art semiconductor devices. However, integrating these new high-κ materials into the existing complementary metal-oxide semiconductor (CMOS) process remains a challenge. One particular area of concern is the use of large amounts of HF during wet etching of hafnium based oxides and silicates. The patterning of thin films of these materials is accomplished by wet etching in HF solutions. The use of HF allows dissolution of hafnium as an anionic fluoride complex. Etch selectivity with respect to SiO2 is achieved by appropriately diluting the solutions and using slightly elevated temperatures. From an ESH point of view, it would be beneficial to develop methods which would lower the use of HF. The first objective of this study is to find new chemistries and developments of new wet etch methods to reduce fluoride consumption during wet etching of hafnium based high-κ materials. Another related issue with major environmental impact is the usage of large amounts of rinsing water for removal of HF in post-etch cleaning step. Both of these require a better understanding of the HF interaction with the high-κ surface during the etching, cleaning, and rinsing processes. During the rinse, the cleaning chemical is removed from the wafers. Ensuring optimal resource usage and cycle time during the rinse requires a sound understanding and quantitative description of the transport effects that dominate the removal rate of the cleaning chemicals from the surfaces. Multiple processes, such as desorption and re-adsorption, diffusion, migration and convection, all factor into the removal rate of the cleaning chemical during the rinse. Any of these processes can be the removal rate limiting process, the bottleneck of the rinse. In fact, the process limiting the removal rate generally changes as the rinse progresses, offering the opportunity to save resources

High Atomic Number Contrast Media Offer Potential for Radiation Dose Reduction in Contrast-Enhanced Computed Tomography.

PubMed

Roessler, Ann-Christin; Hupfer, Martin; Kolditz, Daniel; Jost, Gregor; Pietsch, Hubertus; Kalender, Willi A

2016-04-01

Spectral optimization of x-ray computed tomography (CT) has led to substantial radiation dose reduction in contrast-enhanced CT studies using standard iodinated contrast media. The purpose of this study was to analyze the potential for further dose reduction using high-atomic-number elements such as hafnium and tungsten. As in previous studies, spectra were determined for which the patient dose necessary to provide a given contrast-to-noise ratio (CNR) is minimized. We used 2 different quasi-anthropomorphic phantoms representing the liver cross-section of a normal adult and an obese adult patient with the lateral widths of 360 and 460 mm and anterior-posterior heights of 200 and 300 mm, respectively. We simulated and measured on 2 different scanners with x-ray spectra from 80 to 140 kV and from 70 to 150 kV, respectively. We determined the contrast for iodine-, hafnium-, and tungsten-based contrast media, the noise, and 3-dimensional dose distributions at all available tube voltages by measurements and by simulations. The dose-weighted CNR was determined as optimization parameter. Simulations and measurements were in good agreement regarding their dependence on energy for all parameters investigated. Hafnium provided the best performance for normal and for obese patient phantoms, indicating a dose reduction potential of 30% for normal and 50% for obese patients at 120 kV compared with iodine; this advantage increased further with higher kV values. Dose-weighted CNR values for tungsten were always slightly below the hafnium results. Iodine proved to be the superior choice at voltage values of 80 kV and below. Hafnium and tungsten both seem to be candidates for contrast-medium-enhanced CT of normal and obese adult patients with strongly reduced radiation dose at unimpaired image quality. Computed tomography examinations of obese patients will decrease in dose for higher kV values.

Constraints on short-term mantle rheology from the J2 observation and the dispersion of the 18.6 y tidal Love number

NASA Technical Reports Server (NTRS)

Sabadini, R.; Yuen, D. A.; Widmer, R.

1985-01-01

Information derived from data recently acquired from the LAGEOS satellite is used to place some constraints on the rheological parameters of short-term mantle rheology. The validity of Lambeck and Nakiboglu's (1983) rheological model is assessed by formally developing an expression for the transformed shear modulus using a truncated retardation spectrum. This analytical formula is used to show that the parameters of the above mentioned model are not consistent at all with the amount of anelastic dispersion expected in the Chandler wobble and with the attenuation of seismic normal modes. The feasibility of a standard linear solid (SLS) rheology operating over intermediate timescales between 1 and 100 yr is investigated to determine whether the tidal dispersion at 18.6 yr can be explained by this model. An attempt is made to place some constraints on the parameters of the SLS model and the nature of short-term mantle rheology for timescales of less than 100 yr is discussed.

Hybrid nuclear reactor grey rod to obtain required reactivity worth

DOEpatents

Miller, John V.; Carlson, William R.; Yarbrough, Michael B.

1991-01-01

Hybrid nuclear reactor grey rods are described, wherein geometric combinations of relatively weak neutron absorber materials such as stainless steel, zirconium or INCONEL, and relatively strong neutron absorber materials, such as hafnium, silver-indium cadmium and boron carbide, are used to obtain the reactivity worths required to reach zero boron change load follow. One embodiment includes a grey rod which has combinations of weak and strong neutron absorber pellets in a stainless steel cladding. The respective pellets can be of differing heights. A second embodiment includes a grey rod with a relatively thick stainless steel cladding receiving relatively strong neutron absorber pellets only. A third embodiment includes annular relatively weak netron absorber pellets with a smaller diameter pellet of relatively strong absorber material contained within the aperture of each relatively weak absorber pellet. The fourth embodiment includes pellets made of a homogeneous alloy of hafnium and a relatively weak absorber material, with the percentage of hafnium chosen to obtain the desired reactivity worth.

Evaluation of T-111 forced-convection loop tested with lithium at 1370 C. [free convection

NASA Technical Reports Server (NTRS)

Devan, J. H.; Long, E. L., Jr.

1975-01-01

A T-111 alloy (Ta-8% W-2% Hf) forced-convection loop containing molten lithium was operated 3000 hr at a maximum temperature of 1370 C. Flow velocities up to 6.3 m/sec were used, and the results of this forced-convection loop are very similar to those observed in lower velocity thermal-convection loops of T-111 containing lithium. Weight changes were determined at 93 positions around the loop. The maximum dissolution rate occurred at the maximum wall temperature of the loop and was less than 1.3 microns/year. Mass transfer of hafnium, nitrogen, and, to a lesser extent, carbon occurred from the hotter to cooler regions. Exposed surfaces in the highest temperature region were found to be depleted in hafnium to a depth of 60 microns with no detectable change in tungsten content. There was some loss in room-temperature tensile strength for specimens exposed to lithium at 1370 C, attributable to depletion of hafnium and nitrogen and to attendant grain growth.

Association between in-hospital mortality and renal dysfunction in 186,219 patients hospitalized for acute stroke in the Emilia-Romagna region of Italy.

PubMed

Fabbian, Fabio; Gallerani, Massimo; Pala, Marco; De Giorgi, Alfredo; Salmi, Raffaella; Dentali, Francesco; Ageno, Walter; Manfredini, Roberto

2014-11-01

Using a regional Italian database, we evaluated the relationship between renal dysfunction and in-hospital mortality (IHM) in patients with acute stroke (ischemic/hemorrhagic). Patients were classified on the basis of renal damage: without renal dysfunction, with chronic kidney disease (CKD), and with end-stage renal disease (ESRD). Of a total of 186,219 patients with a first episode of stroke, 1626 (0.9%) had CKD and 819 (0.4%) had ESRD. Stroke-related IHM (total cases) was independently associated with CKD, ESRD, atrial fibrillation (AF), age, and Charlson comorbidity index (CCI). In patients with ischemic stroke (n=154,026), IHM remained independently associated with CKD, ESRD, AF, and CCI. In patients with hemorrhagic stroke (n=32,189), variables that were independently associated with IHM were CKD, ESRD, and AF. Renal dysfunction is associated with IHM related to stroke, both ischemic and hemorrhagic, with even higher odds ratios than those of other established risk factors, such as age, comorbidities, and AF. © The Author(s) 2013.

Experimental Observations of Nuclear Activity in Deuterated Materials Subjected to a Low-Energy Photon Beam

NASA Technical Reports Server (NTRS)

Steinetz, Bruce M.; Benyo, Theresa L.; Pines, Vladimir; Pines, Marianna; Forsley, Lawrence P.; Westmeyer, Paul A.; Chait, Arnon; Becks, Michael D.; Martin, Richard E.; Hendricks, Robert C.;

Preparation of refractory cermet structures for lithium compatibility testing

NASA Technical Reports Server (NTRS)

Heestand, R. L.; Jones, R. A.; Wright, T. R.; Kizer, D. E.

1973-01-01

High-purity nitride and carbide cermets were synthesized for compatability testing in liquid lithium. A process was developed for the preparation of high-purity hafnium nitride powder, which was subsequently blended with tungsten powder or tantalum nitride and tungsten powders and fabricated into 3 in diameter billets by uniaxial hot pressing. Specimens were then cut from the billets for compatability testing. Similar processing techniques were applied to produce hafnium carbide and zirconium carbide cermets for use in the testing program. All billets produced were characterized with respect to chemistry, structure, density, and strength properties.

Sol-gel-derived double-layered nanocrystal memory

NASA Astrophysics Data System (ADS)

Ko, Fu-Hsiang; You, Hsin-Chiang; Lei, Tan-Fu

2006-12-01

The authors have used the sol-gel spin-coating method to fabricate a coexisting hafnium silicate and zirconium silicate double-layered nanocrystal (NC) memories. From transmission electron microscopic and x-ray photoelectron spectroscopic analyses, the authors determined that the hafnium silicate and zirconium silicate NCs formed after annealing at 900°C for 1min. When using channel hot electron injection for charging and band-to-band tunneling-induced hot hole injection for discharging, the NC memories exhibited superior Vth shifting because of the higher probability for trapping the charge carrier.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rodenbücher, C.; Hildebrandt, E.; Sharath, S. U.

On highly oxygen deficient thin films of hafnium oxide (hafnia, HfO{sub 2−x}) contaminated with adsorbates of carbon oxides, the formation of hafnium carbide (HfC{sub x}) at the surface during vacuum annealing at temperatures as low as 600 °C is reported. Using X-ray photoelectron spectroscopy the evolution of the HfC{sub x} surface layer related to a transformation from insulating into metallic state is monitored in situ. In contrast, for fully stoichiometric HfO{sub 2} thin films prepared and measured under identical conditions, the formation of HfC{sub x} was not detectable suggesting that the enhanced adsorption of carbon oxides on oxygen deficient films providesmore » a carbon source for the carbide formation. This shows that a high concentration of oxygen vacancies in carbon contaminated hafnia lowers considerably the formation energy of hafnium carbide. Thus, the presence of a sufficient amount of residual carbon in resistive random access memory devices might lead to a similar carbide formation within the conducting filaments due to Joule heating.« less

Transanal total mesorectal excision: pathological results of 186 patients with mid and low rectal cancer.

PubMed

de Lacy, F Borja; van Laarhoven, Jacqueline J E M; Pena, Romina; Arroyave, María Clara; Bravo, Raquel; Cuatrecasas, Miriam; Lacy, Antonio M

2018-05-01

Transanal total mesorectal excision (TaTME) seems to be a valid alternative to the open or laparoscopic TME. Quality of the TME specimen is the most important prognostic factor in rectal cancer. This study shows the pathological results of the largest single-institution series published on TaTME in patients with mid and low rectal cancer. We conducted a retrospective cohort study of all consecutive patients with rectal cancer, treated by TaTME between November 2011 and June 2016. Patient data were prospectively included in a standardized database. Patients with all TNM stages of mid (5-10 cm from the anal verge) and low (0-5 cm from the anal verge) rectal cancer were included. A total of 186 patients were included. Tumor was in the mid and low rectum in, respectively, 62.9 and 37.1%. Neoadjuvant chemoradiotherapy was given in 62.4%, only radiotherapy in 3.2%, and only chemotherapy in 2.2%. Preoperative staging showed T1 in 3.2%, T2 in 20.4%, T3 in 67.7%, and T4 in 7.5%. Mesorectal resection quality was complete in 95.7% (n = 178), almost complete in 1.6% (n = 3), and incomplete in 1.1% (n = 2). Overall positive CRM (≤ 1 mm) and DRM (≤ 1 mm) were 8.1% (n = 15) and 3.2% (n = 6), respectively. The composite of complete mesorectal excision, negative CRM, and negative DRM was achieved in 88.1% (n = 155) of the patients. The median number of lymph nodes found per specimen was 14.0 (IQR 11-18). The present study showed good rates regarding total mesorectal excision, negative circumferential, and distal resection margins. As the specimen quality is a surrogate marker for survival, TaTME can be regarded as a safe method to treat patients with rectal cancer, from an oncological point of view.

Coupled antiferromagnetic spin-1/2 chains in green dioptase, Cu6 [Si6O18.6] H2O

NASA Astrophysics Data System (ADS)

Podlesnyak, Andrey; Anovitz, L. M.; Kolesnikov, A. I.; Matsuda, M.; Prisk, T. R.; Ehlers, G.; Toth, S.

Gem crystals of natural dioptase with colors ranging from emerald-green to bluish have delighted people since ancient times and still attract attention of mineral collectors around the globe. The crystal structure of green dioptase (space group R 3) consists of corrugated silicate rings Si6O<18 interconnected by Cu2+ ions. Oxygen atoms form axially-elongated octahedral of CuO4(H2O)2. The magnetic ground state of green dioptase remains controversial. We report inelastic neutron scattering measurements of the magnetic excitations of green dioptase Cu6 [ Si6O18.6 ] H2O. The observed spectrum contains two magnetic modes and a prominent spin gap that is consistent with the ordered ground state of Cu moments coupled antiferromagnetically in spiral chains along the c axis and ferromagnetically in ab planes on the hexagonal cell. The data are in excellent agreement with a spin-1/2 Hamiltonian that includes AFM nearest-neighbor intra-chain coupling Jc = 10 . 6 (1) meV, ferromagnetic inter-chain coupling Jab = - 1 . 2 (1) meV and exchange anisotropy ΔJc = 0 . 14 (1) meV. This appears compatible with reduced Nèel temperature, TN = 14 . 5 K <

Study of gas tungsten arc welding procedures for tantalum alloy T-111 (Ta-8 W-2Hf) plate

NASA Technical Reports Server (NTRS)

Gold, R. E.; Kesterson, R. L.

1973-01-01

Methods of eliminating or reducing underbread cracking in multipass GTA welds in thick T-111 plate were studied. Single V butt welds prepared using experimental filler metal compositions and standard weld procedures resulted in only moderate success in reducing underbread cracking. Subsequent procedural changes incorporating manual welding, slower weld speeds, and three or fewer fill passes resulted in crack-free single V welds only when the filler metal was free of hafnium. The double V joint design with successive fill passes on opposite sides of the joint produced excellent welds. The quality of each weld was determined metallographically since the cracking, when present, was very slight and undetectable using standard NDT techniques. Tensile and bend tests were performed on selected weldments. The inherent filler metal strength and the joint geometry determined the strength of the weldment. Hardness and electron beam microprobe traverses were made on selected specimens with the result that significant filler metal-base metal dilution as well as hafnium segregation was detected. A tentative explanation of T-111 plate underbread cracking is presented based on the intrinsic effects of hafnium in the weldment.

PRODUCTION OF HAFNIUM METAL

DOEpatents

Elger, G.W.; Boubel, R.W.

1963-01-01

This patent deals with a process of producing pure Hf metal from oxygen- contaminated gaseous Hf chloride. The oxygen compounds in the chioride gas are halogenated by contacting the gas at elevated temperature with Cl/sub 2/ in the presence of C. The Hf chloride, still in gaseous form, is contacted with molten Mg whereby Hf metal is formed and condensed on the Mg. (AEC)

Preservation of Earth-forming events in the tungsten isotopic composition of modern flood basalts.

PubMed

Rizo, Hanika; Walker, Richard J; Carlson, Richard W; Horan, Mary F; Mukhopadhyay, Sujoy; Manthos, Vicky; Francis, Don; Jackson, Matthew G

2016-05-13

How much of Earth's compositional variation dates to processes that occurred during planet formation remains an unanswered question. High-precision tungsten isotopic data from rocks from two large igneous provinces, the North Atlantic Igneous Province and the Ontong Java Plateau, reveal preservation to the Phanerozoic of tungsten isotopic heterogeneities in the mantle. These heterogeneities, caused by the decay of hafnium-182 in mantle domains with high hafnium/tungsten ratios, were created during the first ~50 million years of solar system history, indicating that portions of the mantle that formed during Earth's primary accretionary period have survived to the present. Copyright © 2016, American Association for the Advancement of Science.

A normative database and determinants of lexical retrieval for 186 Arabic nouns: effects of psycholinguistic and morpho-syntactic variables on naming latency.

PubMed

Khwaileh, Tariq; Body, Richard; Herbert, Ruth

2014-12-01

Research into lexical retrieval requires pictorial stimuli standardised for key psycholinguistic variables. Such databases exist in a number of languages but not in Arabic. In addition there are few studies of the effects of psycholinguistic and morpho-syntactic variables on Arabic lexical retrieval. The current study identified a set of culturally and linguistically appropriate concept labels, and corresponding photographic representations for Levantine Arabic. The set included masculine and feminine nouns, nouns from both types of plural formation (sound and broken), and both rational and irrational nouns. Levantine Arabic speakers provided norms for visual complexity, imageability, age of acquisition, naming latency and name agreement. This delivered a normative database for a set of 186 Arabic nouns. The effects of the morpho-syntactic and the psycholinguistic variables on lexical retrieval were explored using the database. Imageability and age of acquisition were the only significant determinants of successful lexical retrieval in Arabic. None of the other variables, including all the linguistic variables, had any effect on production time. The normative database is available for the use of clinicians and researchers in the Arab world in the domains of speech and language pathology, neurolinguistics and psycholinguistics. The database and the photographic representations will be soon available for free download from the first author's personal webpage or via email.

STEM and APT characterization of scale formation on a La,Hf,Ti-doped NiCrAl model alloy.

PubMed

Unocic, Kinga A; Chen, Yimeng; Shin, Dongwon; Pint, Bruce A; Marquis, Emmanuelle A

2018-06-01

A thermally grown scale formed on a cast NiCrAl model alloy doped with lanthanum, hafnium, and titanium was examined after isothermal exposure at 1100 °C for 100 h in dry flowing O 2 to understand the dopant segregation along scale grain boundaries. The complex scale formed on the alloy surface was composed of two types of substrates: phase-dependent, thin (<250 nm) outer layers and a columnar-grained ∼3.5 μm inner alumina layer. Two types of oxides formed between the inner and outer scale layers: small (3-15 nm) La 2 O 3 and larger (≤50 nm) HfO 2 oxide precipitates. Nonuniform distributions of the hafnium, lanthanum, and titanium dopants were observed along the inner scale grain boundaries, with hafnium dominating in most of the grain boundaries of α-Al 2 O 3. The concentration of reactive elements (RE) seemed to strongly depend on the grain boundary structure. The level of titanium grain boundary segregation in the inner scale decreased toward the model alloy (substrate), confirming the fast outward diffusion of titanium. Hafnium was also observed at the metal-scale interface and in the γ' (Ni 3 Al) phase of the alloy. High-resolution scanning transmission electron microscopy (STEM) confirmed the substitution of REs for aluminum atoms at the scale grain boundaries, consistent with both the semiconducting band structure and the site-blocking models. Both STEM and atom probe tomography allowed quantification of REs along the scale grain boundaries across the scale thickness. Analysis of the scale morphology after isothermal exposure in flowing oxygen revealed a myriad of new precipitate phases, RE segregation dependence on grain boundary type, and atomic arrangement along scale grain boundaries, which is expected to influence the scale growth rate, stability, and mechanical properties. Copyright © 2018 Elsevier Ltd. All rights reserved.

A change in the geodynamics of continental growth 3 billion years ago.

PubMed

Dhuime, Bruno; Hawkesworth, Chris J; Cawood, Peter A; Storey, Craig D

2012-03-16

Models for the growth of continental crust rely on knowing the balance between the generation of new crust and the reworking of old crust throughout Earth's history. The oxygen isotopic composition of zircons, for which uranium-lead and hafnium isotopic data provide age constraints, is a key archive of crustal reworking. We identified systematic variations in hafnium and oxygen isotopes in zircons of different ages that reveal the relative proportions of reworked crust and of new crust through time. Growth of continental crust appears to have been a continuous process, albeit at variable rates. A marked decrease in the rate of crustal growth at ~3 billion years ago may be linked to the onset of subduction-driven plate tectonics.

[Immobilization of pectawamorine G10x on silichromes].

PubMed

Bogatskiĭ, A V; Davidenko, T I; Gren', T A

1980-01-01

Immobilization of pectawamorine G10x on silochromes, using cyanuric chloride, 2,4-toluylene diisocyanate, glutaric dialdehyde, thionyl chloride, phosphorus tribromide, titanium tetrachloride, zirconium oxychloride and hafnium oxychloride was studied. The use of glutaric dialdehyde assured the strongest binding and the preatest stability of activity. Properties of the native pectawamorine G10x and immobilized preparations were studied on a comparative basis. Pectawamorine G10x immobilized by means of hafnium oxychloride showed increased stability when stored at 5 degrees C and used repeatedly. In every case, except for cyanuric chloride and glutaric dialdehyde, maximum activity was at a temperature 10 degrees C higher than for the native enzyme, and optimum pH varied for the preparations with different binding reagents.

Investigation to develop a method to apply diffusion barrier to high strength fibers

NASA Technical Reports Server (NTRS)

Veltri, R. D.; Paradis, R. D.; Douglas, F. C.

1975-01-01

A radio frequency powered ion plating process was used to apply the diffusion barriers of aluminum oxide, yttrium oxide, hafnium oxide and titanium carbide to a substrate tungsten fiber. Each of the coatings was examined as to its effect on both room temperature strength and tensile strength of the base tungsten fiber. The coated fibers were then overcoated with a nickel alloy to become single cell diffusion couples. These diffusion couples were exposed to 1093 C for 24 hours, cycled between room temperature and 1093 C, and given a thermal anneal for 100 hours at 1200 C. Tensile testing and metallographic examinations determined that the hafnium oxide coating produced the best high temperature diffusion barrier for tungsten of the four coatings.

BROADBAND JET EMISSION IN YOUNG AND POWERFUL RADIO SOURCES: THE CASE OF THE COMPACT STEEP SPECTRUM QUASAR 3C 186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Migliori, Giulia; Siemiginowska, Aneta; Celotti, Annalisa, E-mail: migliori@cfa.harvard.edu

2012-04-20

We present the X-ray analysis of a deep ({approx}200 ks) Chandra observation of the compact steep spectrum radio-loud quasar 3C 186 (z = 1.06) and investigate the contribution of the unresolved radio jet to the total X-ray emission. The spectral analysis is not conclusive on the origin of the bulk of the X-ray emission. In order to examine the jet contribution to the X-ray flux, we model the quasar spectral energy distribution, adopting several scenarios for the jet emission. For the values of the main physical parameters favored by the observables, a dominant role of the jet emission in themore » X-ray band is ruled out when a single-zone (leptonic) scenario is adopted, even including the contribution of the external photon fields as seed photons for inverse Compton emission. We then consider a structured jet, with the blazar component that-although not directly visible in the X-ray band-provides an intense field of seed synchrotron photons Compton-scattered by electrons in a mildly relativistic knot. In this case, the whole X-ray emission can be accounted for if we assume a blazar luminosity within the range observed from flat spectrum radio quasars. The X-ray radiative efficiency of such a (structured) jet is intimately related to the presence of a complex velocity structure. The jet emission can provide a significant contribution in X-rays if it decelerates within the host galaxy on kiloparsec scales. We discuss the implications of this model in terms of jet dynamics and interaction with the ambient medium.« less

40 CFR 471.95 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... I—PSNS. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium rinsed following molten salt treatment Chromium 0.333...

40 CFR 471.95 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... I—PSNS. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium rinsed following molten salt treatment Chromium 0.333...

40 CFR 471.95 - Pretreatment standards for new sources (PSNS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... I—PSNS. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium rinsed following molten salt treatment Chromium 0.333...

Design of thermoelectrically highly efficient Heusler compounds using phase separations and nano-composites under an economic point of view

NASA Astrophysics Data System (ADS)

Balke, Benjamin

Half-Heusler (HH) compounds are one of the most promising candidates for thermoelectric materials for automotive and industrial waste heat recovery applications. In this talk, I will give an overview about our recent investigations of phase separations in HH thermoelectrics, focusing on the ternary system TiNiSn-ZrNiSn-HfNiSn. I will show how we adapted this knowledge to design a p-type HH compound which exhibits a ZT that is increased by 130% compared to the best published bulk p-type Heusler. I will also present how we used the phase separation to design thermoelectric highly efficient nano-composites of different single-phase materials. Since the price for Hafnium doubled within the last year, our research focused on the design of HH compounds without Hafnium. I will present a very recent calculation on ZT per Euro and efficiency per Euro for various materials followed by our latest very promising results for n-type Heusler compunds without Hafnium resulting in 20 times higher ZT/Euro values. These results strongly underline the importance of phase separations as a powerful tool for designing highly efficient materials for thermoelectric applications that fulfill the industrial demands for a thermoelectric converter. The author gratefully acknowledges financial support by the thermoHEUSLER2 Project (Project No. 19U15006F) of the German Federal Ministry of Economics and Technology (BMWi).

Alkali metal hafnium oxide scintillators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bourret-Courchesne, Edith; Derenzo, Stephen E.; Taylor, Scott Edward

The present invention provides for a composition comprising an inorganic scintillator comprising an alkali metal hafnate, optionally cerium-doped, having the formula A 2HfO 3:Ce; wherein A is an alkali metal having a valence of 1, such as Li or Na; and the molar percent of cerium is 0% to 100%. The alkali metal hafnate are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

Cathodoluminescence of Irradiated Hafnium Dioxide

DTIC Science & Technology

2011-03-01

d allows for a smaller A for a given C, but the insulator can only become so thin before tunneling occurs, which causes high power consumption and... coefficient is given by 4 Inπα λ = , (2.7) where λ is the vacuum wavelength of the light [11]. Luminescence is the general term for the...between localized states in the band tails, while the 4.2 eV feature is excited due to the interband absorption. Strzhemechny et al., 2008, studied

Nickel aluminides and nickel-iron aluminides for use in oxidizing environments

DOEpatents

Liu, Chain T.

1988-03-15

Nickel aluminides and nickel-iron aluminides treated with hafnium or zirconium, boron and cerium to which have been added chromium to significantly improve high temperature ductility, creep resistance and oxidation properties in oxidizing environments.

40 CFR 471.94 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... I—PSES. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide...

40 CFR 471.94 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2014 CFR

2014-07-01

... I—PSES. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide...

40 CFR 471.94 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2012 CFR

2012-07-01

... I—PSES. There shall be no discharge of process wastewater pollutants. (p) Molten salt rinse. Subpart... (pounds per million off-pounds) of zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide...

Chemical precursors to non-oxide ceramics: Macro to nanoscale materials

NASA Astrophysics Data System (ADS)

Forsthoefel, Kersten M.

Non-oxide ceramics exhibit a number of important properties that make them ideal for technologically important applications (thermal and chemical stability, high strength and hardness, wear-resistance, light weight, and a range of electronic and optical properties). Unfortunately, traditional methodologies to these types of materials are limited to fairly simple shapes and complex processed forms cannot be attained through these methods. The establishment of the polymeric precursor approach has allowed for the generation of advanced materials, such as refractory non-oxide ceramics, with controlled compositions, under moderate conditions, and in processed forms. The goal of the work described in this dissertation was both to develop new processible precursors to technologically important ceramics and to achieve the formation of advanced materials in processed forms. One aspect of this research exploited previously developed preceramic precursors to boron carbide, boron nitride and silicon carbide for the generation of a wide variety of advanced materials: (1) ultra-high temperature ceramic (UHTC) structural materials composed of hafnium boride and related composite materials, (2) the quaternary borocarbide superconductors, and (3) on the nanoscale, non-oxide ceramic nanotubules. The generation of the UHTC and the quaternary borocarbide materials was achieved through a method that employs a processible polymer/metal(s) dispersion followed by subsequent pyrolyses. In the case of the UHTC, hafnium oxide, hafnium, or hafnium boride powders were dispersed in a suitable precursor to afford hafnium borides or related composite materials (HfB2/HfC, HfB2/HfN, HfB2/SiC) in high yields and purities. The quaternary borocarbide superconducting materials were produced from pyrolyses of dispersions containing appropriate stoichiometric amounts of transition metal, lanthanide metal, and the polyhexenyldecaborane polymer. Both chemical vapor deposition (CVD) based routes employing a

Compatibility of refractory materials for nuclear reactor poison control systems

NASA Technical Reports Server (NTRS)

Sinclair, J. H.

1974-01-01

Metal-clad poison rods have been considered for the control system of an advanced space power reactor concept studied at the NASA Lewis Research Center. Such control rods may be required to operate at temperatures of about 140O C. Selected poison materials (including boron carbide and the diborides of zirconium, hafnium, and tantalum) were subjected to 1000-hour screening tests in contact with candidate refractory metal cladding materials (including tungsten and alloys of tantalum, niobium, and molybdenum) to assess the compatibility of these materials combinations at the temperatures of interest. Zirconium and hafnium diborides were compatible with refractory metals at 1400 C, but boron carbide and tantalum diboride reacted with the refractory metals at this temperature. Zirconium diboride also showed promise as a reaction barrier between boron carbide and tungsten.

Atomic Layer Deposition of HfO2 and Si Nitride on Ge Substrates

NASA Astrophysics Data System (ADS)

Zhu, Shiyang; Nakajima, Anri

2007-12-01

Hafnium oxide (HfO2) thin films were deposited on Ge substrates at 300 °C using atomic layer deposition (ALD) with tetrakis(diethylamino)hafnium (termed as TDEAH) as a precursor and water as an oxidant. The deposition rate was estimated to be 0.09 nm/cycle and the deposited HfO2 films have a smooth surface and an almost stoichiometric composition, indicating that the growth follows a layer-by-layer kinetics, similarly to that on Si substrates. Si nitride thin films were also deposited on Ge by ALD using SiCl4 as a precursor and NH3 as an oxidant. Si nitride has a smaller deposition rate of about 0.055 nm/cycle and a larger gate leakage current than HfO2 deposited on Ge by ALD.

Development of Advanced Environmental Barrier Coatings for SiC/SiC Ceramic Matrix Composites: Path Toward 2700 F Temperature Capability and Beyond

NASA Technical Reports Server (NTRS)

Zhu, Dongming; Harder, Bryan; Hurst, Janet B.; Good, Brian; Costa, Gustavo; Bhatt, Ramakrishna T.; Fox, Dennis S.

2017-01-01

Advanced environmental barrier coating systems for SiC-SiC Ceramic Matrix Composite (CMC) turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant coating development challenges is to achieve prime-reliant environmental barrier coating systems to meet the future 2700F EBC-CMC temperature stability and environmental durability requirements. This presentation will emphasize recent NASA environmental barrier coating system testing and down-selects, particularly the development path and properties towards 2700-3000F durability goals by using NASA hafnium-hafnia-rare earth-silicon-silicate composition EBC systems for the SiC-SiC CMC turbine component applications. Advanced hafnium-based compositions for enabling next generation EBC and CMCs capabilities towards ultra-high temperature ceramic coating systems will also be briefly mentioned.

40 CFR 471.93 - New source performance standards (NSPS).

Code of Federal Regulations, 2014 CFR

2014-07-01

... of process wastewater pollutants (p) Molten salt rinse. Subpart I—NSPS Pollutant or pollutant... zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide 0.220 0.091 Nickel 1.45 0.960...

40 CFR 471.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

... of process wastewater pollutants. (p) Molten salt rinse. Subpart I—BAT Pollutant or pollutant... zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide 0.220 0.091 Nickel 1.45 0.960...

40 CFR 471.92 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

... of process wastewater pollutants. (p) Molten salt rinse. Subpart I—BAT Pollutant or pollutant... zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide 0.220 0.091 Nickel 1.45 0.960...

40 CFR 471.91 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Degreasing rinse—subpart I—BPT. There shall be no discharge or process wastewater pollutants. (p) Molten salt.../off-kg (pounds per million off pounds) of zirconium-hafnium treated with molten salt Chromium 3.33 1...

40 CFR 471.93 - New source performance standards (NSPS).

Code of Federal Regulations, 2012 CFR

2012-07-01

... of process wastewater pollutants (p) Molten salt rinse. Subpart I—NSPS Pollutant or pollutant... zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide 0.220 0.091 Nickel 1.45 0.960...

40 CFR 471.93 - New source performance standards (NSPS).

Code of Federal Regulations, 2013 CFR

2013-07-01

... of process wastewater pollutants (p) Molten salt rinse. Subpart I—NSPS Pollutant or pollutant... zirconium-hafnium treated with molten salt Chromium 0.333 0.136 Cyanide 0.220 0.091 Nickel 1.45 0.960...

40 CFR 471.91 - Effluent limitations representing the degree of effluent reduction attainable by the application...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Degreasing rinse—subpart I—BPT. There shall be no discharge or process wastewater pollutants. (p) Molten salt.../off-kg (pounds per million off pounds) of zirconium-hafnium treated with molten salt Chromium 3.33 1...

[Management of Uninhabitable Homes - Investigation of 186 Cases of Hoarding, Domestic Neglect and Squalor in Dortmund (Germany)].

PubMed

Lenders, T; Kuster, J; Bispinck, R

2015-07-01

To develop an intervention concept for the management of uninhabitable homes. Retrospective analysis of 186 cases of the community mental health service in Dortmund (Germany) presenting with a destitute situation of the domestic environment as core problem. All patients suffered from psychiatric illnesses, mainly from addiction (F1: 41%), psychosis (F2: 17%), depression (F3: 17%), and hoarding disorder (F63.8: 12%). Main socio-demographic characteristics of our sample are: middle age (45-65 years, 48%), male gender (73%), isolated situation (only 7% married, 84% living alone), normal schooling (only 4% without completion of schooling, 7% attended a school for special needs), after initial integration into employment nearly all patients suffered vocational disintegration (5% employed, 44% unemployment benefit, 7% welfare, 39% pension or invalidity benefit). Psychosocial interventions differed between the 4 main diagnostic groups: F1: treatment of dependence (rehab) and treatment of concomitant somatic diseases; F2: admission to a psychiatric hospital and implementation of guardianship; F3: mediation of conflicts with neighbours/landlords and implementation of guardianship; F63.8: direct practical help by members of the community mental health team and organisation of home help/waste disposal. In all diagnostic groups, acceptance of help was impaired due to social withdrawal, resistance and psychiatric symptoms. At 13%, compliance with help and interventions was lowest in the hoarder group (F1: 27%, F2: 26%, F3: 38%). Consequently, in this group the poor outcome categories "nothing accomplished" and "lost flat/eviction" were more frequent (44%, F1: 27%, F2: 26%, F3: 38%). Concurrent to the deterioration of the domestic situation, patients suffer vocational disintegration as well as family and social isolation. Uninhabitable homes occur in the course of various severe and chronic psychiatric diseases. They don't constitute a syndrome and they are not characteristic

HIGH-REDSHIFT X-RAY COOLING-CORE CLUSTER ASSOCIATED WITH THE LUMINOUS RADIO-LOUD QUASAR 3C 186

DOE Office of Scientific and Technical Information (OSTI.GOV)

Siemiginowska, Aneta; Burke, D. J.; Aldcroft, Thomas L.

2010-10-10

We present the first results from a new, deep (200 ks) Chandra observation of the X-ray luminous galaxy cluster surrounding the powerful (L {approx} 10{sup 47} erg s{sup -1}), high-redshift (z = 1.067), compact-steep-spectrum radio-loud quasar 3C 186. The diffuse X-ray emission from the cluster has a roughly ellipsoidal shape and extends out to radii of at least {approx}60 arcsec ({approx}500 kpc). The centroid of the diffuse X-ray emission is offset by 0.68 {+-} 0.''11 ({approx}5.5 {+-} 0.9 kpc) from the position of the quasar. We measure a cluster mass within the radius at which the mean enclosed density ismore » 2500 times the critical density, r{sub 2500} = 283{sup +18}{sub -13} kpc, of 1.02{sup +0.21}{sub -0.14} x 10{sup 14} M{sub sun}. The gas-mass fraction within this radius is f{sub gas} = 0.129{sup +0.015}{sub -0.016}. This value is consistent with measurements at lower redshifts and implies minimal evolution in the f{sub gas}(z) relation for hot, massive clusters at 0 < z < 1.1. The measured metal abundance of 0.42{sup +0.08}{sub -0.07} Solar is consistent with the abundance observed in other massive, high-redshift clusters. The spatially resolved temperature profile for the cluster shows a drop in temperature, from kT {approx} 8 keV to kT {approx} 3 keV, in its central regions that is characteristic of cooling-core clusters. This is the first spectroscopic identification of a cooling-core cluster at z>1. We measure cooling times for the X-ray emitting gas at radii of 50 kpc and 25 kpc of 1.7 {+-} 0.2 x 10{sup 9} years and 7.5 {+-} 2.6 x 10{sup 8} years, as well as a nominal cooling rate (in the absence of heating) of 400 {+-} 190 M{sub sun} year{sup -1} within the central 100 kpc. In principle, the cooling gas can supply enough fuel to support the growth of the supermassive black hole and to power the luminous quasar. The radiative power of the quasar exceeds by a factor of 10 the kinematic power of the central radio source, suggesting that radiative

Hafnium and neodymium isotopes and REY distribution in the truly dissolved, nanoparticulate/colloidal and suspended loads of rivers in the Amazon Basin, Brazil

NASA Astrophysics Data System (ADS)

Merschel, Gila; Bau, Michael; Schmidt, Katja; Münker, Carsten; Dantas, Elton L.

2017-09-01

Radiogenic isotopes in river sediments and river waters have been widely used in provenance studies, as these samples naturally integrate the geology/chemistry of the entire catchment. While the Hf and Nd isotope systems are coupled during igneous processes, they are decoupled during supergene processes at the Earth's surface, which is reflected by the isotope composition of riverine sediments. We present the first data for both Hf and Nd isotope compositions of the dissolved (0.2 μm-filtrates rich in nanoparticles and colloids, NPCs) and the truly dissolved (1 kDa-ultrafiltrates) load of rivers. Hafnium and Nd isotope compositions and concentrations of the Rare Earths and Yttrium (REY) and Hf were determined for suspended particles (>0.2 μm) as well as for the dissolved and the truly dissolved load of the Rio Solimões, the Amazon's largest tributary draining the Andes, and of the Rio Negro, an organic NPC- and particle-rich river draining the rainforest of northern Amazonia. We also analyzed the Nd isotope compositions of suspended sediments and 0.2 μm-filtered water samples from the Amazon River and its tributaries Rio Tapajos, Rio Xingu and Rio Jari. Our novel results clearly show that the decoupling of the Hf and Nd isotope systems is related to incongruent weathering processes on the continent, as this decoupling can already be observed in the different Hf and Nd pools, i.e. in the particulate, the NPC-dominated dissolved and the truly dissolved load of rivers. In the Rio Negro and Rio Solimões, a strong particle size-dependent difference in Hf isotope composition is observed. Values of εHf become more radiogenic as filter poresize decreases, which can be related to the density- and size-dependent distribution of Hf-rich minerals, e.g. zircons, and their absence from the truly dissolved pool. In contrast, the Nd isotope composition of Amazonian river waters reflects that of their catchment geology. Tributaries draining the Precambrian Brazilian and

Fabrication of cermet bearings for the control system of a high temperature lithium cooled nuclear reactor

NASA Technical Reports Server (NTRS)

Yacobucci, H. G.; Heestand, R. L.; Kizer, D. E.

1973-01-01

The techniques used to fabricate cermet bearings for the fueled control drums of a liquid metal cooled reference-design reactor concept are presented. The bearings were designed for operation in lithium for as long as 5 years at temperatures to 1205 C. Two sets of bearings were fabricated from a hafnium carbide - 8-wt. % molybdenum - 2-wt. % niobium carbide cermet, and two sets were fabricated from a hafnium nitride - 10-wt. % tungsten cermet. Procedures were developed for synthesizing the material in high purity inert-atmosphere glove boxes to minimize oxygen content in order to enhance corrosion resistance. Techniques were developed for pressing cylindrical billets to conserve materials and to reduce machining requirements. Finishing was accomplished by a combination of diamond grinding, electrodischarge machining, and diamond lapping. Samples were characterized in respect to composition, impurity level, lattice parameter, microstructure and density.

40 CFR 421.331 - Specialized definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true Specialized definitions. 421.331 Section 421.331 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Zirconium and Hafnium...

High-strength tungsten alloy with improved ductility

NASA Technical Reports Server (NTRS)

Klopp, W. D.; Raffo, P. L.; Rubenstein, L. S.; Witzke, W. R.

1967-01-01

Alloy combines superior strength at elevated temperatures with improved ductility at lower temperatures relative to unalloyed tungsten. Composed of tungsten, rhenium, hafnium, and carbon, the alloy is prepared by consumable electrode vacuum arc-melting and can be fabricated into rod, plate, and sheet.

40 CFR 421.337 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true [Reserved] 421.337 Section 421.337 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Zirconium and Hafnium Subcategory § 421.337...

40 CFR 421.335 - [Reserved

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 28 2010-07-01 2010-07-01 true [Reserved] 421.335 Section 421.335 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS NONFERROUS METALS MANUFACTURING POINT SOURCE CATEGORY Primary Zirconium and Hafnium Subcategory § 421.335...

Discussion of “Deglacial paleoclimate in the southwestern United States: an abrupt 18.6 cold event and evidence for a North Atlantic forcing of Termination I” by M.S. Lachniet, Y. Asmerom and V. Polyak

USGS Publications Warehouse

Winograd, Isaac J.

2012-01-01

Utilizing a stable isotopic time series obtained from a speleothem (PC-1), which grew between 20.1 and 15.6 ka, Lachniet, Asmeron and Polyak (2011; hereafter LAP) present evidence for a significant cold event in the southern Great Basin at 18.6 ka, a finding that we accept. Supplementing this short record with a literature review, they go on to claim, as their central thesis, that the paleoclimate of the southwestern US was driven by “the transmission of atmospheric anomalies to the southwest…that coincided with deglacial climate changes in Greenland and the North Atlantic region”, not by a “dominant Pacific Ocean SST control” as suggested by SST time series off California and by the Devils Hole δ18O time series from the southern Great Basin. We do not find their central thesis supportable.

Low-temperature fabrication of an HfO2 passivation layer for amorphous indium-gallium-zinc oxide thin film transistors using a solution process.

PubMed

Hong, Seonghwan; Park, Sung Pyo; Kim, Yeong-Gyu; Kang, Byung Ha; Na, Jae Won; Kim, Hyun Jae

2017-11-24

We report low-temperature solution processing of hafnium oxide (HfO 2 ) passivation layers for amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFTs). At 150 °C, the hafnium chloride (HfCl 4 ) precursor readily hydrolyzed in deionized (DI) water and transformed into an HfO 2 film. The fabricated HfO 2 passivation layer prevented any interaction between the back surface of an a-IGZO TFT and ambient gas. Moreover, diffused Hf 4+ in the back-channel layer of the a-IGZO TFT reduced the oxygen vacancy, which is the origin of the electrical instability in a-IGZO TFTs. Consequently, the a-IGZO TFT with the HfO 2 passivation layer exhibited improved stability, showing a decrease in the threshold voltage shift from 4.83 to 1.68 V under a positive bias stress test conducted over 10,000 s.

[Management of Uninhabitable Homes - Investigation of 186 Cases of Hoarding, Domestic Neglect and Squalor in Dortmund (Germany)].

PubMed

Lenders, T; Kuster, J; Bispinck, R

2015-12-01

To develop an intervention concept for the management of uninhabitable homes. Retrospective analysis of 186 cases of the community mental health service in Dortmund (Germany) presenting with a destitute situation of the domestic environment as core problem. All patients suffered from psychiatric illnesses, mainly from addiction (F1: 41 %), psychosis (F2: 17 %), depression (F3: 17 %), and hoarding disorder (F63.8: 12 %). Main socio-demographic characteristics of our sample are: middle age (45-65 years, 48 %), male gender (73 %), isolated situation (only 7 % married, 84 % living alone), normal schooling (only 4 % without completion of schooling, 7 % attended a school for special needs), after initial integration into employment nearly all patients suffered vocational disintegration (5 % employed, 44 % unemployment benefit, 7 % welfare, 39 % pension or invalidity benefit).Psychosocial interventions differed between the 4 main diagnostic groups: F1: treatment of dependence (rehab) and treatment of concomitant somatic diseases; F2: admission to a psychiatric hospital and implementation of guardianship; F3: mediation of conflicts with neighbours/landlords and implementation of guardianship; F63.8: direct practical help by members of the community mental health team and organisation of home help/waste disposal. In all diagnostic groups, acceptance of help was impaired due to social withdrawal, resistance and psychiatric symptoms. At 13 %, compliance with help and interventions was lowest in the hoarder group (F1: 27 %, F2: 26 %, F3: 38 %). Consequently, in this group the poor outcome categories "nothing accomplished" and "lost flat/eviction" were more frequent (44 %, F1: 27 %, F2: 26 %, F3: 38 %). Concurrent to the deterioration of the domestic situation, patients suffer vocational disintegration as well as family and social isolation. Uninhabitable homes occur in the course of various severe and chronic psychiatric diseases

30 CFR 18.6 - Applications.

Code of Federal Regulations, 2014 CFR

2014-07-01

... metal and not have a compartment exceeding ten (10) feet in length. Glass or polycarbonate materials... polycarbonate windows and lenses shall not exceed 115 °C (240 °F), in normal operation. Other non-metallic... metallic conduit are not permitted. (H) Unused lead entrances shall be closed with a metal plug that is...

30 CFR 18.6 - Applications.

Code of Federal Regulations, 2010 CFR

2010-07-01

... metal and not have a compartment exceeding ten (10) feet in length. Glass or polycarbonate materials... polycarbonate windows and lenses shall not exceed 115 °C (240 °F), in normal operation. Other non-metallic... metallic conduit are not permitted. (H) Unused lead entrances shall be closed with a metal plug that is...

30 CFR 18.6 - Applications.

Code of Federal Regulations, 2011 CFR

2011-07-01

... metal and not have a compartment exceeding ten (10) feet in length. Glass or polycarbonate materials... polycarbonate windows and lenses shall not exceed 115 °C (240 °F), in normal operation. Other non-metallic... metallic conduit are not permitted. (H) Unused lead entrances shall be closed with a metal plug that is...

30 CFR 18.6 - Applications.

Code of Federal Regulations, 2013 CFR

2013-07-01

... metal and not have a compartment exceeding ten (10) feet in length. Glass or polycarbonate materials... polycarbonate windows and lenses shall not exceed 115 °C (240 °F), in normal operation. Other non-metallic... metallic conduit are not permitted. (H) Unused lead entrances shall be closed with a metal plug that is...

30 CFR 18.6 - Applications.

Code of Federal Regulations, 2012 CFR

2012-07-01

... metal and not have a compartment exceeding ten (10) feet in length. Glass or polycarbonate materials... polycarbonate windows and lenses shall not exceed 115 °C (240 °F), in normal operation. Other non-metallic... metallic conduit are not permitted. (H) Unused lead entrances shall be closed with a metal plug that is...

Nuclear Structure of 186Re

DTIC Science & Technology

2016-12-24

D population-depopulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 AME Atomic Mass Evaluation...this mass region are important for validating models of nuclear structure and reactions. The ENSDF feeds a specific data library relevant to nuclear...spherically asymmetric. Spherical asymmetry is common for nuclei between shell closures, such as those in the mid-shell 150  A  190 mass range of interest

36 CFR 223.186 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Service Administrative Units or groups of Administrative Units by the Regional Foresters of Regions 1, 2... struck. Highway yellow paint refers to an oil base or equivalent yellow paint of lasting quality... plant used to convert unprocessed timber into products. Non-manufacturer means a person who does not own...

21 CFR 186.1275 - Dextrans.

Code of Federal Regulations, 2010 CFR

2010-04-01

... weight polysaccharides produced by bacterial fermentation of sucrose. Commercially available dextrans are... purification of the fermented mixture shall produce a product that is free of viable microorganisms. (b) The...

21 CFR 186.1275 - Dextrans.

Code of Federal Regulations, 2013 CFR

2013-04-01

... weight polysaccharides produced by bacterial fermentation of sucrose. Commercially available dextrans are... purification of the fermented mixture shall produce a product that is free of viable microorganisms. (b) The...

21 CFR 186.1275 - Dextrans.

Code of Federal Regulations, 2012 CFR

2012-04-01

... weight polysaccharides produced by bacterial fermentation of sucrose. Commercially available dextrans are... purification of the fermented mixture shall produce a product that is free of viable microorganisms. (b) The...

21 CFR 186.1275 - Dextrans.

Code of Federal Regulations, 2011 CFR

2011-04-01

... weight polysaccharides produced by bacterial fermentation of sucrose. Commercially available dextrans are... purification of the fermented mixture shall produce a product that is free of viable microorganisms. (b) The...

21 CFR 186.1275 - Dextrans.

Code of Federal Regulations, 2014 CFR

2014-04-01

... by bacterial fermentation of sucrose. Commercially available dextrans are synthesized from sucrose by Leuconostoc mesenteroides strain NRRL B-512(F). Partial depolymerization and purification of the fermented...

49 CFR 173.186 - Matches.

Code of Federal Regulations, 2010 CFR

2010-10-01

... matches the heads of which are prepared with a friction-sensitive igniter composition and a pyrotechnic... combined with or attached to the box, book or card that can be ignited by friction only on a prepared surface. (3) Strike anywhere matches are matches that can be ignited by friction on a solid surface. (4...

49 CFR 173.186 - Matches.

Code of Federal Regulations, 2012 CFR

2012-10-01

... matches the heads of which are prepared with a friction-sensitive igniter composition and a pyrotechnic... combined with or attached to the box, book or card that can be ignited by friction only on a prepared surface. (3) Strike anywhere matches are matches that can be ignited by friction on a solid surface. (4...

49 CFR 173.186 - Matches.

Code of Federal Regulations, 2014 CFR

2014-10-01

... matches the heads of which are prepared with a friction-sensitive igniter composition and a pyrotechnic... combined with or attached to the box, book or card that can be ignited by friction only on a prepared surface. (3) Strike anywhere matches are matches that can be ignited by friction on a solid surface. (4...

49 CFR 173.186 - Matches.

Code of Federal Regulations, 2013 CFR

2013-10-01

... matches the heads of which are prepared with a friction-sensitive igniter composition and a pyrotechnic... combined with or attached to the box, book or card that can be ignited by friction only on a prepared surface. (3) Strike anywhere matches are matches that can be ignited by friction on a solid surface. (4...

49 CFR 173.186 - Matches.

Code of Federal Regulations, 2011 CFR

2011-10-01

... matches the heads of which are prepared with a friction-sensitive igniter composition and a pyrotechnic... combined with or attached to the box, book or card that can be ignited by friction only on a prepared surface. (3) Strike anywhere matches are matches that can be ignited by friction on a solid surface. (4...

21 CFR 186.1839 - Sorbose.

Code of Federal Regulations, 2010 CFR

2010-04-01

... microbial oxidation of sorbitol. It also occurs naturally in other plants. Sorbose can be synthesized by the catalytic hydrogenation of glucose to D-sorbitol. The resulting sorbitol can be oxidized by Acetobacter...

36 CFR 223.186 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

.... Should have known means committing an act that a reasonable person in the timber industry would have... unprocessed timber is placed on board an ocean-going vessel, rail car, or other conveyance destined for a...

36 CFR 223.186 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-07-01

.... Should have known means committing an act that a reasonable person in the timber industry would have... unprocessed timber is placed on board an ocean-going vessel, rail car, or other conveyance destined for a...

36 CFR 223.186 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-07-01

.... Should have known means committing an act that a reasonable person in the timber industry would have... unprocessed timber is placed on board an ocean-going vessel, rail car, or other conveyance destined for a...

36 CFR 223.186 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

.... Should have known means committing an act that a reasonable person in the timber industry would have... unprocessed timber is placed on board an ocean-going vessel, rail car, or other conveyance destined for a...

Placental weight in the first pregnancy and risk for preeclampsia in the second pregnancy: A population-based study of 186 859 women.

PubMed

Dypvik, Johanne; Larsen, Sandra; Haavaldsen, Camilla; Jukic, Anne M; Vatten, Lars J; Eskild, Anne

2017-07-01

To study whether placental weight in the first pregnancy is associated with preeclampsia in the second pregnancy. In this population-based study, we included all women with two consecutive singleton pregnancies reported to the Medical Birth Registry of Norway during 1999-2012 (n=186 859). Placental weight in the first pregnancy was calculated as z-scores, and the distribution was divided into five groups of equal size (quintiles). We estimated crude and adjusted odds ratios with 95% confidence intervals for preeclampsia in the second pregnancy according to quintiles of placental weight z-scores in the first pregnancy. The 3rd quintile was used as the reference group. Among women without preeclampsia in the first pregnancy, 1.4% (2507/177 149) developed preeclampsia in the second pregnancy. In these women, the risk for preeclampsia in the second pregnancy was associated with placental weight in the first pregnancy in both lowest (crude odds ratio (cOR) 1.30, 95% confidence interval (CI); 1.14-1.47) and highest quintile (cOR 1.20, 95% CI; 1.06-1.36). The risk associated with the highest quintile of placental weight was confined to term preeclampsia. Among women with preeclampsia in the first pregnancy, 15.7% (1522/9710) developed recurrent preeclampsia, and the risk for recurrent preeclampsia was associated with placental weight in lowest quintile in the first pregnancy (cOR 1.30, 95% CI; 1.10-1.55). Adjustment for interval between pregnancies, maternal diabetes, age, and smoking in the first pregnancy did not alter these estimates notably. Placental weight in the first pregnancy might help to identify women who could be at risk for developing preeclampsia in a second pregnancy. Copyright © 2017 The Authors. Published by Elsevier B.V. All rights reserved.

The puzzling case of the radio-loud QSO 3C 186: a gravitational wave recoiling black hole in a young radio source?

NASA Astrophysics Data System (ADS)

Chiaberge, M.; Ely, J. C.; Meyer, E. T.; Georganopoulos, M.; Marinucci, A.; Bianchi, S.; Tremblay, G. R.; Hilbert, B.; Kotyla, J. P.; Capetti, A.; Baum, S. A.; Macchetto, F. D.; Miley, G.; O'Dea, C. P.; Perlman, E. S.; Sparks, W. B.; Norman, C.

2017-04-01

Context. Radio-loud active galactic nuclei with powerful relativistic jets are thought to be associated with rapidly spinning black holes (BHs). BH spin-up may result from a number of processes, including accretion of matter onto the BH itself, and catastrophic events such as BH-BH mergers. Aims: We study the intriguing properties of the powerful (Lbol 1047 erg s-1) radio-loud quasar 3C 186. This object shows peculiar features both in the images and in the spectra. Methods: We utilize near-IR Hubble Space Telescope (HST) images to study the properties of the host galaxy, and HST UV and Sloan Digital Sky Survey optical spectra to study the kinematics of the source. Chandra X-ray data are also used to better constrain the physical interpretation. Results: HST imaging shows that the active nucleus is offset by 1.3 ± 0.1 arcsec (I.e. 11 kpc) with respect to the center of the host galaxy. Spectroscopic data show that the broad emission lines are offset by -2140 ± 390 km s-1 with respect to the narrow lines. Velocity shifts are often seen in QSO spectra, in particular in high-ionization broad emission lines. The host galaxy of the quasar displays a distorted morphology with possible tidal features that are typical of the late stages of a galaxy merger. Conclusions: A number of scenarios can be envisaged to account for the observed features. While the presence of a peculiar outflow cannot be completely ruled out, all of the observed features are consistent with those expected if the QSO is associated with a gravitational wave (GW) recoiling BH. Future detailed studies of this object will allow us to confirm this type of scenario and will enable a better understanding of both the physics of BH-BH mergers and the phenomena associated with the emission of GW from astrophysical sources.

Oxidation resistant iron and nickel alloys for high temperature use

NASA Technical Reports Server (NTRS)

Hill, V. L.; Misra, S. K.; Wheaton, H. L.

1970-01-01

Iron-base and nickel-base alloys exhibit good oxidation resistance and improved ductility with addition of small amounts of yttrium, tantalum /or hafnium/, and thorium. They can be used in applications above the operating temperatures of the superalloys, if high strength materials are not required.

Hafnium—an optical hydrogen sensor spanning six orders in pressure

PubMed Central

Boelsma, C.; Bannenberg, L. J.; van Setten, M. J.; Steinke, N.-J.; van Well, A. A.; Dam, B.

2017-01-01

Hydrogen detection is essential for its implementation as an energy vector. So far, palladium is considered to be the most effective hydrogen sensing material. Here we show that palladium-capped hafnium thin films show a highly reproducible change in optical transmission in response to a hydrogen exposure ranging over six orders of magnitude in pressure. The optical signal is hysteresis-free within this range, which includes a transition between two structural phases. A temperature change results in a uniform shift of the optical signal. This, to our knowledge unique, feature facilitates the sensor calibration and suggests a constant hydrogenation enthalpy. In addition, it suggests an anomalously steep increase of the entropy with the hydrogen/metal ratio that cannot be explained on the basis of a classical solid solution model. The optical behaviour as a function of its hydrogen content makes hafnium well-suited for use as a hydrogen detection material. PMID:28580959

Real-time atomistic observation of structural phase transformations in individual hafnia nanorods

DOE PAGES

Hudak, Bethany M.; Depner, Sean W.; Waetzig, Gregory R.; ...

2017-05-12

High-temperature phases of hafnium dioxide have exceptionally high dielectric constants and large bandgaps, but quenching them to room temperature remains a challenge. Scaling the bulk form to nanocrystals, while successful in stabilizing the tetragonal phase of isomorphous ZrO 2, has produced nanorods with a twinned version of the room temperature monoclinic phase in HfO 2. Here we use in situ heating in a scanning transmission electron microscope to observe the transformation of an HfO 2 nanorod from monoclinic to tetragonal, with a transformation temperature suppressed by over 1000°C from bulk. When the nanorod is annealed, we observe with atomic-scale resolutionmore » the transformation from twinned-monoclinic to tetragonal, starting at a twin boundary and propagating via coherent transformation dislocation; the nanorod is reduced to hafnium on cooling. Unlike the bulk displacive transition, nanoscale size-confinement enables us to manipulate the transformation mechanism, and we observe discrete nucleation events and sigmoidal nucleation and growth kinetics.« less

Fractionation of Zr and Hf during the differentiation of peralkaline magmatic system (Lovozero rare metal deposit, Kola Peninsula)

NASA Astrophysics Data System (ADS)

Kogarko, Liya

2016-04-01

Zirconium and hafnium are valuable strategic metals. We assessed principal features of the distribution of these elements in peralkaline rocks, ores and rock-forming and accessory minerals of Lovozero complex. The accumulation of these elements during the evolution of alkaline magma of Lovozero deposit up to extremely high concentrations in eudialyte ores (5-8% ZrO2 and 1200-1800 ppm Hf) has been established. These ores represent valuable complex raw material not only for Zr and Hf, but for REE as well. We evaluated partition coefficients of these elements in alkaline pyroxenes (aegirines) from porphyry-like agpaitic lujavrites of Lovozero massif which are 0.40 for zirconium and 0.58 for hafnium. We assessed variations of Zr/Hf ratio for all the rocks of Lovozero alkaline massif. The growth of this ratio in the course of the evolution of alkaline magma has been observed from 38 in the earliest magmatic phase, to 44 in the second phase and to 51-53 in the latest manifestation of alkaline magmatsm. On the basis of the obtained data and equations of equilibrium and fractional crystallization the model of the fractionation of zirconium and hafnium during the evolution of Lovozero intrusion has been constructed. We have demonstrated that the source of strongly enriched magmatic systems similar to Lovozero rare metal deposit is short-lived enriched reservoir - metasomatized and carbonatized mantle substrate. We investigated the fractionation of zirconium and hafnium in carbonatized mantle xenoliths from East Antarctica. The elevated Zr/Hf ratios (up to 125) in metasomatized xenoliths by comparison with the chondritic value have been found. The main reactions of carbonate metasomatism lead to the replacement of primary orthopyroxene by clinopyroxene 2Mg2Si2O6 + CaMg(CO3)2 = 2Mg2SiO4 + CaMgSi2O6 + 2CO2 3CaMg(CO3)2 + CaMgSi2O6 = 4CaCO3 + 2Mg2SiO4 + 2CO2 The substantial expansion of the clinopyroxene crystallization field results in increase of Zr/Hf ratio in equilibrium

Nanomechanical study of amorphous and polycrystalline ALD HfO2 thin films

Treesearch

K. Tapily; J.E. Jakes; D. Gu; H. Baumgart; A.A. Elmustafa

2011-01-01

Thin films of hafnium oxide (HfO2) were deposited by atomic layer deposition (ALD). The structural properties of the deposited films were characterised by transmission electron microscopy (TEM) and X-ray diffraction (XRD). We investigated the effect of phase transformations induced by thermal treatments on the mechanical properties of ALD HfO

Gadolinium: Central Metal of the Lanthanoids

ERIC Educational Resources Information Center

Laing, Michael

2009-01-01

The physical and chemical properties of gadolinium are compared with those of the other lanthanoids. Some properties are intermediate between those of lanthanum and lutetium; some between those of barium and hafnium; and others (unexpectedly) between those of ytterbium and lutetium. Both the remarkably high molar heat capacity of the metal and the…

Gas Tungsten Arc Welding and Plasma Arc Cutting. Teacher Edition.

ERIC Educational Resources Information Center

Fortney, Clarence; And Others

This welding curriculum guide treats two topics in detail: the care of tungsten electrodes and the entire concept of contamination control and the hafnium electrode and its importance in dual-air cutting systems that use compressed shop air for plasma arc cutting activities. The guide contains three units of instruction that cover the following…

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2012 CFR

2012-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2011 CFR

2011-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2013 CFR

2013-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

21 CFR 186.1256 - Clay (kaolin).

Code of Federal Regulations, 2010 CFR

2010-04-01

... CONSUMPTION (CONTINUED) INDIRECT FOOD SUBSTANCES AFFIRMED AS GENERALLY RECOGNIZED AS SAFE Listing of Specific...-58-7) consists of hydrated aluminum silicate. The commercial products of clay (kaolin) contain... kaolin. Kaolinite or china clay is whiter, less contaminated with extraneous minerals, and less plastic...

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... significance. (b) Approved Maps. The appropriate maps for determining the boundaries of the “Niagara Escarpment... Ridge Road, and then east on Ridge Road (State Route 104) about 0.15 mile to the road's first... westward along the contour line (through the Escarpment, Ramsey Ridge, and Lewiston Heights subdivisions...

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... significance. (b) Approved Maps. The appropriate maps for determining the boundaries of the “Niagara Escarpment... Ridge Road, and then east on Ridge Road (State Route 104) about 0.15 mile to the road's first... westward along the contour line (through the Escarpment, Ramsey Ridge, and Lewiston Heights subdivisions...

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2012 CFR

2012-04-01

... Road, then north on Kayner Road 0.65 mile to its junction with the 600-foot contour line; then (12...) Proceed north along the east bank of the Niagara River about 0.6 mile to the northern boundary of the... about 0.8 mile to the park's northeast corner, and continue east in a straight line a short distance to...

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2013 CFR

2013-04-01

... Escarpment”. For purposes of part 4 of this chapter, “Niagara Escarpment” is a term of viticultural... the contour line's junction with Sunset Drive; then (6) Proceed north on Sunset Drive 0.3 mile to its...) Proceed north-northwesterly on Upper Mountain Road 0.65 mile and then northerly on Sunset Drive 0.25 mile...

27 CFR 9.186 - Niagara Escarpment.

Code of Federal Regulations, 2014 CFR

2014-04-01

... Escarpment”. For purposes of part 4 of this chapter, “Niagara Escarpment” is a term of viticultural... the contour line's junction with Sunset Drive; then (6) Proceed north on Sunset Drive 0.3 mile to its...) Proceed north-northwesterly on Upper Mountain Road 0.65 mile and then northerly on Sunset Drive 0.25 mile...

49 CFR 572.186 - Abdomen assembly.

Code of Federal Regulations, 2010 CFR

2010-10-01

... part of the dummy assembly shown in drawing 175-0000 including load sensors specified in § 572.189(e... measuring sensor in the abdomen as shown in Figure U5; (5) The impactor impacts the dummy's abdomen at 4.0 m... of the forces of the three abdominal load sensors, specified in 572.189(e), shall be not less than...

21 CFR 186.1555 - Japan wax.

Code of Federal Regulations, 2013 CFR

2013-04-01

... fruits of the oriental sumac, Rhus succedanea (Japan, Taiwan, and Indo-China), R. vernicifera (Japan), and R. trichocarpa (China, Indo-China, India, and Japan). Japan wax is soluble in hot alcohol, benzene...

21 CFR 186.1555 - Japan wax.

Code of Federal Regulations, 2012 CFR

2012-04-01

... fruits of the oriental sumac, Rhus succedanea (Japan, Taiwan, and Indo-China), R. vernicifera (Japan), and R. trichocarpa (China, Indo-China, India, and Japan). Japan wax is soluble in hot alcohol, benzene...

21 CFR 186.1555 - Japan wax.

Code of Federal Regulations, 2011 CFR

2011-04-01

... fruits of the oriental sumac, Rhus succedanea (Japan, Taiwan, and Indo-China), R. vernicifera (Japan), and R. trichocarpa (China, Indo-China, India, and Japan). Japan wax is soluble in hot alcohol, benzene...

49 CFR 572.186 - Abdomen assembly.

Code of Federal Regulations, 2014 CFR

2014-10-01

... longitudinal axis of the probe's impact face as shown in Figure U5-A in appendix A to this subpart; (4) The... the three load cell forces must be concurrent in time. (2) Maximum impactor force (impact probe...

GADRAS-DRF 18.6 User's Manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Horne, Steve M.; Thoreson, Greg G.; Theisen, Lisa A.

2016-05-01

The Gamma Detector Response and Analysis Software–Detector Response Function (GADRAS-DRF) application computes the response of gamma-ray and neutron detectors to incoming radiation. This manual provides step-by-step procedures to acquaint new users with the use of the application. The capabilities include characterization of detector response parameters, plotting and viewing measured and computed spectra, analyzing spectra to identify isotopes, and estimating source energy distributions from measured spectra. GADRAS-DRF can compute and provide detector responses quickly and accurately, giving users the ability to obtain usable results in a timely manner (a matter of seconds or minutes).

38 CFR 18.6 - Compliance information.

Code of Federal Regulations, 2014 CFR

2014-07-01

... its obligations under this part. In general, recipients should have available for the agency racial... official finds necessary to apprise such persons of the protections against discrimination assured them by...

38 CFR 18.6 - Compliance information.

Code of Federal Regulations, 2013 CFR

2013-07-01

... its obligations under this part. In general, recipients should have available for the agency racial... official finds necessary to apprise such persons of the protections against discrimination assured them by...

38 CFR 18.6 - Compliance information.

Code of Federal Regulations, 2011 CFR

2011-07-01

... its obligations under this part. In general, recipients should have available for the agency racial... official finds necessary to apprise such persons of the protections against discrimination assured them by...

38 CFR 18.6 - Compliance information.

Code of Federal Regulations, 2012 CFR

2012-07-01

... its obligations under this part. In general, recipients should have available for the agency racial... official finds necessary to apprise such persons of the protections against discrimination assured them by...