The thermoregulatory function of the human hand: How do palm and digit proportions affect heat loss?

PubMed

Payne, Stephanie; Macintosh, Alison; Stock, Jay

2018-03-30

The current study assessed whether ecogeographical patterns seen in hand proportions correlate with heat loss directly. Using a brief severe cold immersion experiment on the hand, the influence of hand and digit dimensions on heat loss was evaluated. A sample of 113 living individuals were tested. Two-dimensional and three-dimensional scanning techniques were used to assess hand and digit dimensions. Thermal imaging analysis was used to quantify heat loss during a 3-min ice-water immersion of the hands. When body size was accounted for, hand width and digit length relative to total hand length were significant predictors of heat loss from the hand. The current study provides empirical evidence to support the link between thermodynamic principles relating to surface area-to-volume ratio, and ecogeographical patterns associated with temperature. © 2018 Wiley Periodicals, Inc.

Inundation Mapping for Heterogeneous Land Covers with Synthetic Aperture Radar and Auxiliary Data

NASA Astrophysics Data System (ADS)

Aristizabal, F.; Judge, J.

2017-12-01

Synthetic Aperture Radar (SAR) has been widely used to detect surface water inundation and provides an advantage over multi-spectral instruments due to cloud penetration and higher spatial resolutions. However, detecting inundation for densely vegetated and urban areas with SAR remains a challenge due to corner reflection and diffuse scattering. Additionally, flat urban surfaces such as roads exhibit similar backscatter coefficients as urban surface water. Differences between inundated and non-inundated backscatter over vegetated land covers of static spatial domains have been demonstrated in previous studies. However, these backscatter differences are sensitive to changes in water depth, soil moisture, SAR sensor parameters, terrain, and vegetation properties. These factors tend to make accurate inundation mapping of heterogeneous regions across varying spatial and temporal extents difficult with exclusive use of SAR. This study investigates the utility of auxiliary data specifically high-resolution (10m) terrain information in conjunction with SAR (10m) for detecting inundated areas. Digital elevation models provide an absolute elevation which could enhance inundation mapping given a limited study extent with similar topography. To counter this limitation, a hydrologically relevant terrain index is proposed known as the Height Above Nearest Drainage (HAND) which normalizes topography to the local relative elevation of the nearest point along the relevant drainage line. HAND has been used for assisting remote sensing inundation mapping in the pre-processing stage as a terrain correction tool and as a post-processing mask that eliminates areas of low inundation risk. While the latter technique is useful for reduction of commission errors, it does not employ HAND for reducing omission errors that can occur from dense vegetation, spectral noise, and urban features. Sentinel-1 dual-pol SAR as well as auxiliary HAND will be used as predictors by various supervised and unsupervised classification algorithms. The October 2016 record flood caused by Hurricane Matthew along the Neuse River in North Carolina will be used as a study area. For validation, locally inundated areas will be derived from observed river stages and high water marks furnished by the U.S. Geological Survey.

Effect of familial sinistrality on planum temporale surface and brain tissue asymmetries.

PubMed

Tzourio-Mazoyer, Nathalie; Simon, Gregory; Crivello, Fabrice; Jobard, Gael; Zago, Laure; Perchey, Guy; Hervé, Pierre-Yves; Joliot, Marc; Petit, Laurent; Mellet, Emmanuel; Mazoyer, Bernard

2010-06-01

The impact of having left-handers (LHs) among one's close relatives, called familial sinistrality (FS), on neuroanatomical markers of left-hemisphere language specialization was studied in 274 normal adults, including 199 men and 75 women, among whom 77 men and 27 women were positive for FS. Measurements of the surface of a phonological cortical area, the "planum temporale" (PT), and gray and white matter hemispheric volumes and asymmetries were made using brain magnetic resonance images. The size of the left PT of subjects with left-handed close relatives (FS+) was reduced by 10%, decreasing with the number of left-handed relatives, and lowest when the subject's mother was left-handed. Such findings had no counterparts in the right hemisphere, and the subject's handedness and sex were found to have no significant effect or interaction with FS on the left PT size. The FS+ subjects also exhibited increased gray matter volume, reduced hemispheric gray matter leftward asymmetry, and, in LHs, reduced strength of hand preference. These results add to the increasing body of evidence suggesting multiple and somewhat independent mechanisms for the inheritance of hand and language lateralization.

The TINS Lecture. The parietal association cortex in depth perception and visual control of hand action.

PubMed

Sakata, H; Taira, M; Kusunoki, M; Murata, A; Tanaka, Y

1997-08-01

Recent neurophysiological studies in alert monkeys have revealed that the parietal association cortex plays a crucial role in depth perception and visually guided hand movement. The following five classes of parietal neurons covering various aspects of these functions have been identified: (1) depth-selective visual-fixation (VF) neurons of the inferior parietal lobule (IPL), representing egocentric distance; (2) depth-movement sensitive (DMS) neurons of V5A and the ventral intraparietal (VIP) area representing direction of linear movement in 3-D space; (3) depth-rotation-sensitive (RS) neurons of V5A and the posterior parietal (PP) area representing direction of rotary movement in space; (4) visually responsive manipulation-related neurons (visual-dominant or visual-and-motor type) of the anterior intraparietal (AIP) area, representing 3-D shape or orientation (or both) of objects for manipulation; and (5) axis-orientation-selective (AOS) and surface-orientation-selective (SOS) neurons in the caudal intraparietal sulcus (cIPS) sensitive to binocular disparity and representing the 3-D orientation of the longitudinal axes and flat surfaces, respectively. Some AOS and SOS neurons are selective in both orientation and shape. Thus the dorsal visual pathway is divided into at least two subsystems, V5A, PP and VIP areas for motion vision and V6, LIP and cIPS areas for coding position and 3-D features. The cIPS sends the signals of 3-D features of objects to the AIP area, which is reciprocally connected to the ventral premotor (F5) area and plays an essential role in matching hand orientation and shaping with 3-D objects for manipulation.

Surface States and Effective Surface Area on Photoluminescent P-Type Porous Silicon

NASA Technical Reports Server (NTRS)

Weisz, S. Z.; Porras, A. Ramirez; Resto, O.; Goldstein, Y.; Many, A.; Savir, E.

1997-01-01

The present study is motivated by the possibility of utilizing porous silicon for spectral sensors. Pulse measurements on the porous-Si/electrolyte system are employed to determine the surface effective area and the surface-state density at various stages of the anodization process used to produce the porous material. Such measurements were combined with studies of the photoluminescence spectra. These spectra were found to shift progressively to the blue as a function of anodization time. The luminescence intensity increases initially with anodization time, reaches a maximum and then decreases with further anodization. The surface state density, on the other hand, increases with anodization time from an initial value of about 2 x 10(exp 12)/sq cm surface to about 1013 sq cm for the anodized surface. This value is attained already after -2 min anodization and upon further anodization remains fairly constant. In parallel, the effective surface area increases by a factor of 10-30. This behavior is markedly different from the one observed previously for n-type porous Si.

Brain Morphometry on Congenital Hand Deformities based on Teichmüller Space Theory.

PubMed

Peng, Hao; Wang, Xu; Duan, Ye; Frey, Scott H; Gu, Xianfeng

2015-01-01

Congenital Hand Deformities (CHD) are usually occurred between fourth and eighth week after the embryo is formed. Failure of the transformation from arm bud cells to upper limb can lead to an abnormal appearing/functioning upper extremity which is presented at birth. Some causes are linked to genetics while others are affected by the environment, and the rest have remained unknown. CHD patients develop prehension through the use of their hands, which affect the brain as time passes. In recent years, CHD have gain increasing attention and researches have been conducted on CHD, both surgically and psychologically. However, the impacts of CHD on brain structure are not well-understood so far. Here, we propose a novel approach to apply Teichmüller space theory and conformal welding method to study brain morphometry in CHD patients. Conformal welding signature reflects the geometric relations among different functional areas on the cortex surface, which is intrinsic to the Riemannian metric, invariant under conformal deformation, and encodes complete information of the functional area boundaries. The computational algorithm is based on discrete surface Ricci flow, which has theoretic guarantees for the existence and uniqueness of the solutions. In practice, discrete Ricci flow is equivalent to a convex optimization problem, therefore has high numerically stability. In this paper, we compute the signatures of contours on general 3D surfaces with surface Ricci flow method, which encodes both global and local surface contour information. Then we evaluated the signatures of pre-central and post-central gyrus on healthy control and CHD subjects for analyzing brain cortical morphometry. Preliminary experimental results from 3D MRI data of CHD/control data demonstrate the effectiveness of our method. The statistical comparison between left and right brain gives us a better understanding on brain morphometry of subjects with Congenital Hand Deformities, in particular, missing the distal part of the upper limb.

Factors predicting health status and recovery of hand function after hand burns in the second year after hospital discharge.

PubMed

Knight, Amber; Wasiak, Jason; Salway, Jacqueline; O'Brien, Lisa

2017-02-01

Hands are the most commonly burnt body part given humans' innate response to guard their face from injury, and are known to have detrimental functional and psychological consequences. Conflicting evidence exists regarding the impact of hand burns on long-term health status and global functioning. The objective of this study was to identify patient and clinical characteristics that predict health status and hand function of people at 12-24 months after hand burn. The Burns Specific Health Scale-Brief (BSHS-B) and the Brief Michigan Hand Outcome Questionnaire (Brief MHQ) were administered to community-dwelling adults who were between one and two years after admission to a statewide burns service for burns including one or both hands. Demographic, injury, and treatment data were collected to identify which factors predict health status and hand function in the second year after admission. Linear regression analyses adjusted for total burn surface area and burn depth were conducted to identify important predictors or outcomes. The sample (n=41) was 80.5% male, with a mean age of 44.5 years and total body surface area (TBSA) of 8.4%. Psychiatric illness (regression coefficient -56.6, confidence interval (95% CI) -76.70, -36.49) and female gender (-20.3; 95% CI -0.77, -40.29) were key predictors of poorer global health status on the BSHS-B. Females also scored worse on body image (-5.35; 95% CI -1.83, -8.87) and work (-4.13; 95% CI -0.64, -7.62) domains of BSHS-B. The need for reconstructive or secondary surgery (-38.84; 95% CI -58.04, -19.65) and female gender (-16.30; 95% CI -4.03, -28.57) were important predictors of poorer hand function. Women and those with a history of psychiatric illness are particularly vulnerable to poorer outcomes in health status and/or hand function after burns, and may benefit from more intensive rehabilitation support and long-term follow-up. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Roles of surface water areas for water and solute cycle in Hanoi city, Viet Nam

NASA Astrophysics Data System (ADS)

Hayashi, Takeshi; Kuroda, Keisuke; Do Thuan, An; Tran Thi Viet, Nga; Takizawa, Satoshi

2013-04-01

Hanoi city, the capital of Viet Nam, has developed beside the Red river. Recent rapid urbanization of this city has reduced a large number of natural water areas such as lakes, ponds and canals not only in the central area but the suburban area. Contrary, the urbanization has increased artificial water areas such as pond for fish cultivation and landscaping. On the other hand, the urbanization has induced the inflow of waste water from households and various kinds of factories to these water areas because of delay of sewerage system development. Inflow of the waste water has induced eutrophication and pollution of these water areas. Also, there is a possibility of groundwater pollution by infiltration of polluted surface water. However, the role of these water areas for water cycle and solute transport is not clarified. Therefore, this study focuses on the interaction between surface water areas and groundwater in Hanoi city to evaluate appropriate land development and groundwater resource management. We are carrying out three approaches: a) understanding of geochemical characteristics of surface water and groundwater, b) monitoring of water levels of pond and groundwater, c) sampling of soil and pond sediment. Correlation between d18O and dD of precipitation (after GNIP), the Red River (after GNIR) and the water samples of this study showed that the groundwater is composed of precipitation, the Red River and surface water that has evaporation process. Contribution of the surface water with evaporation process was widely found in the study area. As for groundwater monitoring, the Holocene aquifers at two sites were in unconfined condition in dry season and the groundwater levels in the aquifer continued to increase through rainy season. The results of isotopic analysis and groundwater level monitoring showed that the surface water areas are one of the major groundwater sources. On the other hand, concentrations of dissolved Arsenic (filtered by 0.45um) in the pore water of the pond sediments were much higher than the pond water and closed to that of groundwater. Also, other metal elements showed the same trend. This result suggested that Arsenic and other metal elements recharged to these ponds is probably adsorbed and removed by sediments (including organic matters). That is, pond sediment plays an important role for solute transport as a filter of Arsenic and metal elements. The results of this study strongly suggest that the natural and artificial surface water areas have important roles for water cycle and solute transport in Hanoi city. Although the number of the natural water areas is decreasing, dredging of artificial water areas increases the infiltration from the surface to aquifers. Therefore, qualitative and quantitative preservation of the surface water areas is important for conservation of groundwater environment and contribute to sustainable groundwater management in Hanoi city.

An image-guided tool to prevent hospital acquired infections

NASA Astrophysics Data System (ADS)

Nagy, Melinda; Szilágyi, László; Lehotsky, Ákos; Haidegger, Tamás; Benyó, Balázs

2011-03-01

Hospital Acquired Infections (HAI) represent the fourth leading cause of death in the United States, and claims hundreds of thousands of lives annually in the rest of the world. This paper presents a novel low-cost mobile device|called Stery-Hand|that helps to avoid HAI by improving hand hygiene control through providing an objective evaluation of the quality of hand washing. The use of the system is intuitive: having performed hand washing with a soap mixed with UV re ective powder, the skin appears brighter in UV illumination on the disinfected surfaces. Washed hands are inserted into the Stery-Hand box, where a digital image is taken under UV lighting. Automated image processing algorithms are employed in three steps to evaluate the quality of hand washing. First, the contour of the hand is extracted in order to distinguish the hand from the background. Next, a semi-supervised clustering algorithm classies the pixels of the hand into three groups, corresponding to clean, partially clean and dirty areas. The clustering algorithm is derived from the histogram-based quick fuzzy c-means approach, using a priori information extracted from reference images, evaluated by experts. Finally, the identied areas are adjusted to suppress shading eects, and quantied in order to give a verdict on hand disinfection quality. The proposed methodology was validated through tests using hundreds of images recorded in our laboratory. The proposed system was found robust and accurate, producing correct estimation for over 98% of the test cases. Stery-Hand may be employed in general practice, and it may also serve educational purposes.

The effect of an instant hand sanitizer on blood glucose monitoring results.

PubMed

Mahoney, John J; Ellison, John M; Glaeser, Danielle; Price, David

2011-11-01

People with diabetes mellitus are instructed to clean their skin prior to self-monitoring of blood glucose to remove any dirt or food residue that might affect the reading. Alcohol-based hand sanitizers have become popular when soap and water are not available. The aim of this study was to determine whether a hand sanitizer is compatible with glucose meter testing and effective for the removal of exogenous glucose. We enrolled 34 nonfasting subjects [14 male/20 female, mean ages 45 (standard deviation, 9.4)] years, 2 with diagnosed diabetes/32 without known diabetes]. Laboratory personnel prepared four separate fingers on one hand of each subject by (1) cleaning the second finger with soap and water and towel drying (i.e., control finger), (2) cleaning the third finger with an alcohol-based hand sanitizer, (3) coating the fourth finger with cola and allowing it to air dry, and (4) coating the fifth finger with cola and then cleaning it with the instant hand sanitizer after the cola had dried. Finger sticks were performed on each prepared finger and blood glucose was measured. Several in vitro studies were also performed to investigate the effectiveness of the hand sanitizer for removal of exogenous glucose.z Mean blood glucose values from fingers cleaned with instant hand sanitizer did not differ significantly from the control finger (p = .07 and .08, respectively) and resulted in 100% accurate results. Blood glucose data from the fourth (cola-coated) finger were substantially higher on average compared with the other finger conditions, but glucose data from the fifth finger (cola-coated then cleaned with hand sanitizer) was similar to the control finger. The data from in vitro experiments showed that the hand sanitizer did not adversely affect glucose meter results, but when an exogenous glucose interference was present, the effectiveness of the hand sanitizer on glucose bias (range: 6% to 212%) depended on the surface area and degree of dilution. In our study, use of an instant hand sanitizer was compatible with the results of a blood glucose monitor and did not affect finger stick blood glucose results. However, depending on surface area, hand sanitizers may not be adequate for cleaning the skin prior to glucose meter testing. © 2011 Diabetes Technology Society.

The Effect of an Instant Hand Sanitizer on Blood Glucose Monitoring Results

PubMed Central

Mahoney, John J; Ellison, John M; Glaeser, Danielle; Price, David

2011-01-01

Background People with diabetes mellitus are instructed to clean their skin prior to self-monitoring of blood glucose to remove any dirt or food residue that might affect the reading. Alcohol-based hand sanitizers have become popular when soap and water are not available. The aim of this study was to determine whether a hand sanitizer is compatible with glucose meter testing and effective for the removal of exogenous glucose. Methods We enrolled 34 nonfasting subjects [14 male/20 female, mean ages 45 (standard deviation, 9.4)] years, 2 with diagnosed diabetes/32 without known diabetes]. Laboratory personnel prepared four separate fingers on one hand of each subject by (1) cleaning the second finger with soap and water and towel drying (i.e., control finger), (2) cleaning the third finger with an alcohol-based hand sanitizer, (3) coating the fourth finger with cola and allowing it to air dry, and (4) coating the fifth finger with cola and then cleaning it with the instant hand sanitizer after the cola had dried. Finger sticks were performed on each prepared finger and blood glucose was measured. Several in vitro studies were also performed to investigate the effectiveness of the hand sanitizer for removal of exogenous glucose.z Results Mean blood glucose values from fingers cleaned with instant hand sanitizer did not differ significantly from the control finger (p = .07 and .08, respectively) and resulted in 100% accurate results. Blood glucose data from the fourth (cola-coated) finger were substantially higher on average compared with the other finger conditions, but glucose data from the fifth finger (cola-coated then cleaned with hand sanitizer) was similar to the control finger. The data from in vitro experiments showed that the hand sanitizer did not adversely affect glucose meter results, but when an exogenous glucose interference was present, the effectiveness of the hand sanitizer on glucose bias (range: 6% to 212%) depended on the surface area and degree of dilution. Conclusions In our study, use of an instant hand sanitizer was compatible with the results of a blood glucose monitor and did not affect finger stick blood glucose results. However, depending on surface area, hand sanitizers may not be adequate for cleaning the skin prior to glucose meter testing. PMID:22226262

Optimizing Health Care Environmental Hygiene.

PubMed

Carling, Philip C

2016-09-01

This article presents a review and perspectives on aspects of optimizing health care environmental hygiene. The topics covered include the epidemiology of environmental surface contamination, a discussion of cleaning health care patient area surfaces, an overview of disinfecting health care surfaces, an overview of challenges in monitoring cleaning versus cleanliness, a description of an integrated approach to environmental hygiene and hand hygiene as interrelated disciplines, and an overview of the research opportunities and challenges related to health care environmental hygiene. Copyright © 2016 Elsevier Inc. All rights reserved.

Quantifying Forearm Muscle Activity during Wrist and Finger Movements by Means of Multi-Channel Electromyography

PubMed Central

Gazzoni, Marco; Celadon, Nicolò; Mastrapasqua, Davide; Paleari, Marco; Margaria, Valentina; Ariano, Paolo

2014-01-01

The study of hand and finger movement is an important topic with applications in prosthetics, rehabilitation, and ergonomics. Surface electromyography (sEMG) is the gold standard for the analysis of muscle activation. Previous studies investigated the optimal electrode number and positioning on the forearm to obtain information representative of muscle activation and robust to movements. However, the sEMG spatial distribution on the forearm during hand and finger movements and its changes due to different hand positions has never been quantified. The aim of this work is to quantify 1) the spatial localization of surface EMG activity of distinct forearm muscles during dynamic free movements of wrist and single fingers and 2) the effect of hand position on sEMG activity distribution. The subjects performed cyclic dynamic tasks involving the wrist and the fingers. The wrist tasks and the hand opening/closing task were performed with the hand in prone and neutral positions. A sensorized glove was used for kinematics recording. sEMG signals were acquired from the forearm muscles using a grid of 112 electrodes integrated into a stretchable textile sleeve. The areas of sEMG activity have been identified by a segmentation technique after a data dimensionality reduction step based on Non Negative Matrix Factorization applied to the EMG envelopes. The results show that 1) it is possible to identify distinct areas of sEMG activity on the forearm for different fingers; 2) hand position influences sEMG activity level and spatial distribution. This work gives new quantitative information about sEMG activity distribution on the forearm in healthy subjects and provides a basis for future works on the identification of optimal electrode configuration for sEMG based control of prostheses, exoskeletons, or orthoses. An example of use of this information for the optimization of the detection system for the estimation of joint kinematics from sEMG is reported. PMID:25289669

Teaching Basic Science Environmentally.

ERIC Educational Resources Information Center

Busch, Phyllis S.

1984-01-01

Five activities on the concept of evaporation as a cooling process is presented. Activities include discovering which hand, the wet one or dry one, is cooler; reviving a wilted plant; measuring surface area of leaves; collecting water vapor from leaves; and finding out the cooling effect of trees. (ERB)

City Geology.

ERIC Educational Resources Information Center

Markle, Sandra

1989-01-01

This article provides information on the evolution of the building material, concrete, and suggests hands-on activities that allow students to experience concrete's qualities, test the heat absorbency of various ground surface materials, discover how an area's geology changes, and search for city fossils. A reproducible activity sheet is included.…

2008 Homeland Security S and T Stakeholders Conference West volume 2 Monday

DTIC Science & Technology

2008-01-16

per collection and pressure to be applied, etc. . - Enviromental effects; dry vs. wet surface (vs. type of sample swipe), clean vs. dirty surfaces...selection of collection via low volume or high volume sampling, distance to suspect item critical, etc. - Enviromental effects; temperature (range of...selection of material, collection via hand wiping or sampling wand, area per collection and pressure to be applied, etc. . - Enviromental effects; dry

Dose assessment of 2% chlorhexidine acetate for canine superficial pyoderma.

PubMed

Murayama, Nobuo; Terada, Yuri; Okuaki, Mio; Nagata, Masahiko

2011-10-01

The dose of 2% chlorhexidine acetate (2CA; Nolvasan(®) Surgical Scrub; Fort Dodge Animal Health, Fort Dodge, IA, USA) for canine superficial pyoderma was evaluated. The first trial compared three doses (group 1, 57 mL/m(2) body surface area; group 2, 29 mL/m(2) body surface area; and group 3, 19 mL/m(2) body surface area) in a randomized, double-blind, controlled fashion. Twenty-seven dogs with superficial pyoderma were treated with 2CA at the allocated doses every 2 days for 1 week. The owners and investigators subjectively evaluated the dogs, and investigators scored skin lesions, including erythema, papules/pustules, alopecia and scales, on a 0-4 scale. There were no significant differences in response between the treatment groups. The second trial established a practical dose-measuring method for 2CA. Sixty-eight owners were asked to apply 2CA on their palm in an amount corresponding to a Japanese ¥500 coin, 26.5 mm in diameter. This yielded an average dose of 0.90±0.40 mL. Mathematically, the doses used in groups 1, 2 and 3 can be represented as one coin per approximately one-, two- and three-hand-sized lesions, respectively. The results therefore suggest that owners instructed to apply one coin of the product per two-hand-sized areas of superficial pyoderma would use the range of doses evaluated in this trial. © 2011 The Authors. Veterinary Dermatology. © 2011 ESVD and ACVD.

Cross-sectional point prevalence survey to study the environmental contamination of nosocomial pathogens in intensive care units under real-life conditions.

PubMed

Wille, I; Mayr, A; Kreidl, P; Brühwasser, C; Hinterberger, G; Fritz, A; Posch, W; Fuchs, S; Obwegeser, A; Orth-Höller, D; Lass-Flörl, C

2018-01-01

In intensive care units (ICUs), inanimate surfaces and equipment may be contaminated by nosocomial pathogens, including multi-drug-resistant micro-organisms. To assess the degree of environmental contamination close to and distant from patients, and contamination of healthcare workers' (HCWs) hands with nosocomial pathogens under real-life conditions and to investigate potential transmission events. Over the course of three weeks, agar contact samples were taken close to and distant from patient areas and from HCWs' hands in eight ICUs of a tertiary care hospital in Innsbruck, Austria. Each ICU was visited once without announcement. Species identification and antimicrobial susceptibility testing were performed according to standard methods, and corresponding strains from patient, environment and hand samples were genotyped using pulsed-field gel electrophoresis. Among 523 samples, HCWs' hands were most frequently contaminated with potentially pathogenic bacteria (15.2%), followed by areas close to patients (10.9%) and areas distant from patients (9.1%). Gram-positive bacteria were identified most often (67.8%), with Enterococcus spp. being the most prevalent species (70% vancomycin sensitive and 30% vancomycin resistant) followed by Staphylococcus aureus, of which 64% were classified as meticillin-resistant Staphylococcus aureus. Molecular typing documented identical strains among patient, environment and hand isolates. This study found widespread contamination of the ICU environment with clinically relevant pathogens, including multi-drug-resistant micro-organisms, despite cleaning and disinfection. The bioburden might not be restricted to areas close to patients. The role of extended environmental disinfection of areas distant from patients in order to improve infection prevention needs further discussion. Copyright © 2017 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Galle Crater

NASA Technical Reports Server (NTRS)

2002-01-01

(Released 19 June 2002) The Science This image is of part of Galle Crater, located at 51.9S, 29.5W. This image was taken far enough south and late enough into the southern hemisphere fall to catch observe water ice clouds partially obscuring the surface. The most striking aspect of the surface is the dissected layered unit to the left in the image. Other areas also appear to have layering, but they are either more obscured by clouds or are less well defined on the surface. The layers appear to be mostly flat lying and layer boundaries appear as topographic lines would on a map, but there are a few areas where it appears that these layers have been deformed to some level. Other areas of the image contain rugged, mountainous terrain as well as a separate pitted terrain where the surface appears to be a separate unit from the mountains and the layered terrain. The Story Galle Crater is officially named after a German astronomer who, in 1846, was the first to observe the planet Neptune. It is better known, however, as the 'Happy Face Crater.' The image above focuses on too small an area of the crater to see its beguiling grin, but you can catch the rocky line of a 'half-smile' in the context image to the right (to the left of the red box). While water ice clouds make some of the surface harder to see, nothing detracts from the fabulous layering at the center left-hand edge of the image. If you click on the above image, the scalloped layers almost look as if a giant knife has swirled through a landscape of cake frosting. These layers, the rugged, mountains near them, and pits on the surface (upper to middle section of the image on the right-hand side) all create varying textures on the crater floor. With such different features in the same place, geologists have a lot to study to figure out what has happened in the crater since it formed.

1 μm-thickness ultra-flexible and high electrode-density surface electromyogram measurement sheet with 2 V organic transistors for prosthetic hand control.

PubMed

Fuketa, Hiroshi; Yoshioka, Kazuaki; Shinozuka, Yasuhiro; Ishida, Koichi; Yokota, Tomoyuki; Matsuhisa, Naoji; Inoue, Yusuke; Sekino, Masaki; Sekitani, Tsuyoshi; Takamiya, Makoto; Someya, Takao; Sakurai, Takayasu

2014-12-01

A 64-channel surface electromyogram (EMG) measurement sheet (SEMS) with 2 V organic transistors on a 1 μm-thick ultra-flexible polyethylene naphthalate (PEN) film is developed for prosthetic hand control. The surface EMG electrodes must satisfy the following three requirements; high mechanical flexibility, high electrode density and high signal integrity. To achieve high electrode density and high signal integrity, a distributed and shared amplifier (DSA) architecture is proposed, which enables an in-situ amplification of the myoelectric signal with a fourfold increase in EMG electrode density. In addition, a post-fabrication select-and-connect (SAC) method is proposed to cope with the large mismatch of organic transistors. The proposed SAC method reduces the area and the power overhead by 96% and 98.2%, respectively, compared with the use of conventional parallel transistors to reduce the transistor mismatch by a factor of 10.

PAH EXPOSURES OF NINE PRESCHOOL CHILDREN

EPA Science Inventory

The exposures to 20 polycyclic aromatic hydrocarbons (PAH) of 9 children, ages 2-5 yr, were measured over 48 hr at day care and at home. Sampled media included indoor and outdoor air, floor dust, outdoor play area soil, hand surface, and solid and liquid food. Urine samples ...

Development of a trash harvester for MnDOT : phase II.

DOT National Transportation Integrated Search

2008-07-01

Trash collection along a roadside is usually done by hand which requires a lot of workers and time. There are : machines available to remove trash on smooth surfaces such as concrete, but none of them are able to pick-up litter : on grassy areas. : T...

Hand preference and magnetic resonance imaging asymmetries of the central sulcus.

PubMed

Foundas, A L; Hong, K; Leonard, C M; Heilman, K M

1998-04-01

Hand preference is perhaps the most evident behavioral asymmetry observed in humans. Anatomic brain asymmetries that may be associated with hand preference have not been extensively studied, and no clear relationship between asymmetries of the motor system and hand preference have been established. Therefore, using volumetric magnetic resonance imaging methodologies, the surface area of the hand representation was measured along the length of the central sulcus in 15 consistent right- and 15 left-handers matched for age and gender. There was a significant leftward asymmetry of the motor hand area of the precentral gyrus in the right-handers, but no directional asymmetry was found in the left-handers. When asymmetry quotients were computed to determine the distribution of interhemispheric asymmetries, the left motor bank was greater than the right motor bank in 9 of 15 right-handers, the right motor bank was greater than the left motor bank in 3 of 15 right-handers, and the motor banks were equal in 3 of 15 right-handers. In contrast, among left-handers, the left motor bank was greater than the right motor bank in 5 of 15, the right motor bank was greater than the left motor bank in 5 of 15, and the motor banks were equal in 5 of 15. Although no direct measure of motor dexterity and skill was performed, these data suggest that anatomic asymmetries of the motor hand area may be related to hand preference because of the differences in right-handers and left-handers. Furthermore, the predominant leftward asymmetry in right-handers and the random distribution of asymmetries in the left-handers support Annett's right-shift theory. It is unclear, however, whether these asymmetries are the result of preferential hand use or are a reflection of a biologic preference to use one limb over the other.

Usability of small impact craters on small surface areas in crater count dating: Analysing examples from the Harmakhis Vallis outflow channel, Mars

NASA Astrophysics Data System (ADS)

Kukkonen, S.; Kostama, V.-P.

2018-05-01

The availability of very high-resolution images has made it possible to extend crater size-frequency distribution studies to small, deca/hectometer-scale craters. This has enabled the dating of small and young surface units, as well as recent, short-time and small-scale geologic processes that have occurred on the units. Usually, however, the higher the spatial resolution of space images is, the smaller area is covered by the images. Thus the use of single, very high-resolution images in crater count age determination may be debatable if the images do not cover the studied region entirely. Here we compare the crater count results for the floor of the Harmakhis Vallis outflow channel obtained from the images of the ConTeXt camera (CTX) and High Resolution Imaging Science Experiment (HiRISE) aboard the Mars Reconnaissance Orbiter (MRO). The CTX images enable crater counts for entire units on the Harmakhis Vallis main valley, whereas the coverage of the higher-resolution HiRISE images is limited and thus the images can only be used to date small parts of the units. Our case study shows that the crater count data based on small impact craters and small surface areas mainly correspond with the crater count data based on larger craters and more extensive counting areas on the same unit. If differences between the results were founded, they could usually be explained by the regional geology. Usually, these differences appeared when at least one cratering model age is missing from either of the crater datasets. On the other hand, we found only a few cases in which the cratering model ages were completely different. We conclude that the crater counts using small impact craters on small counting areas provide useful information about the geological processes which have modified the surface. However, it is important to remember that all the crater counts results obtained from a specific counting area always primarily represent the results from the counting area-not the whole unit. On the other hand, together with crater count results from extensive counting areas and lower-resolution images, crater counts on small counting areas but by using very high-resolution images is a very valuable tool for obtaining unique additional information about the local processes on the surface units.

Vacuum probe surface sampler

NASA Technical Reports Server (NTRS)

Zahlava, B. A. (Inventor)

1973-01-01

A vacuum probe surface sampler is described for rapidly sampling relatively large surface areas which possess relatively light loading densities of micro-organism, drug particles or the like. A vacuum head with a hollow handle connected to a suitable vacuum source is frictionally attached to a cone assembly terminating in a flared tip adapted to be passed over the surface to be sampled. A fine mesh screen carried by the vacuum head provides support for a membrane filter which collects the microorganisms or other particles. The head assembly is easily removed from the cone assembly without contacting the cone assembly with human hands.

Fort Leonard Wood Maintenance and Repair Manual: Black Officer’s Club

DTIC Science & Technology

2005-06-01

chalk and dulled by sanding.) On the other hand, if painted exterior wood surfaces display continuous patterns of deep cracks or if they are...before long the mildew will grow right through the new coating. B. PREPARE GLOSSY SURFACES Glossy areas should be dulled or paint/primer will not...34 appearance. • Changing the configuration of a roof by adding new features such as dormer windows, vents, or skylights so that the historic character

VLSI Implementation of Digital Fourier Transforms.

DTIC Science & Technology

1982-11-01

If we use this lemna and the identities (29) and (30) to expand (34). we arrive at ",)(l., , )BR l - ) • • , ,, - - , (36) :.:"s "’" n -( 01)/(L...moving potential wells, that travel along the surface of the silicon crystal. Information is contained as a packet of minority carriers in these moving...drain areas (figure 29). Charge coupled devices on the other hand move minority carriers through lightly doped substrate regions close to the surface. The

The geomorphic evolution of the lunar surface.

NASA Technical Reports Server (NTRS)

Ronca, L. B.

1972-01-01

The solution of the function relating craters of the continuous degradation sequence with degree of erosion was defined as the geomorphic index of the area. Studies of the geomorphic index of stratigraphic surfaces show that areas covered by considerable ballistic sediments have a geomorphic index which is not a monotonic function of time. On the other hand, areas covered almost exclusively by mare flooding show an index which is a monotonic function of the age of the flooding. As each mare surface shows a considerable range in indices, it is concluded that maria are covered by surfaces formed through a considerable length of time. By using Apollo 11 and 12 radiometric ages it is suggested that the time of mare flooding lasted on the order of one billion years. The geomorphic index of highland surfaces shows a remarkable degree of order - i.e., the farther an area is inland from the mare shores, the higher will be the index. No explanation is given for this phenomenon, but it is suggested that lunar erosion is not just a localized phenomenon centered on the locus of an impact, but has lateral trends of regional dimensions.

Effect of hydrogen on void initiation in tensile test of carbon steel JIS-S25C

NASA Astrophysics Data System (ADS)

Sugawa, S.; Tsutsumi, N.; Oda, K.

2018-06-01

In order to investigate the effect of hydrogen on tensile fracture mechanism of a carbon steel, tensile tests were conducted. Pre-strain specimens (0%, 5% and 10%) were used to study the effect of hydrogen content, since saturated hydrogen content in specimens increases in increasing dislocation density. The tensile strength and the yield stress of hydrogen specimens were almost the same as uncharged. In contrast, the reduction of area of hydrogen charged specimens was smaller than that of uncharged. To reveal the reasons of decrease of the reduction of area, the fracture surface and longitudinal cross section near the fracture surface were observed. On the fracture surface of uncharged specimens, only dimples were observed. On the other hand, dimples and flat fracture surface were observed on the fracture surface of hydrogen charged. On the longitudinal cross section of hydrogen charged specimens, many voids were observed compared to uncharged. From these observations, it is showed that hydrogen gives a rise to the increase of voids and the hydrogen charged specimens break without sufficient necking, thus hydrogen makes the reduction of area smaller.

The dynamics of methicillin-resistant Staphylococcus aureus exposure in a hospital model and the potential for environmental intervention.

PubMed

Plipat, Nottasorn; Spicknall, Ian H; Koopman, James S; Eisenberg, Joseph Ns

2013-12-17

Methicillin-resistant Staphylococcus aureus (MRSA) is a major cause of healthcare-associated infections. An important control strategy is hand hygiene; however, non-compliance has been a major problem in healthcare settings. Furthermore, modeling studies have suggested that the law of diminishing return applies to hand hygiene. Other additional control strategies such as environmental cleaning may be warranted, given that MRSA-positive individuals constantly shed contaminated desquamated skin particles to the environment. We constructed and analyzed a deterministic environmental compartmental model of MRSA fate, transport, and exposure between two hypothetical hospital rooms: one with a colonized patient, shedding MRSA; another with an uncolonized patient, susceptible to exposure. Healthcare workers (HCWs), acting solely as vectors, spread MRSA from one patient room to the other. Although porous surfaces became highly contaminated, their low transfer efficiency limited the exposure dose to HCWs and the uncolonized patient. Conversely, the high transfer efficiency of nonporous surfaces allows greater MRSA transfer when touched. In the colonized patient's room, HCW exposure occurred more predominantly through the indirect (patient to surfaces to HCW) mode compared to the direct (patient to HCW) mode. In contrast, in the uncolonized patient's room, patient exposure was more predominant in the direct (HCW to patient) mode compared to the indirect (HCW to surfaces to patient) mode. Surface wiping decreased MRSA exposure to the uncolonized patient more than daily surface decontamination. This was because wiping allowed higher cleaning frequency and cleaned more total surface area per day. Environmental cleaning should be considered as an integral component of MRSA infection control in hospitals. Given the previously under-appreciated role of surface contamination in MRSA transmission, this intervention mode can contribute to an effective multiple barrier approach in concert with hand hygiene.

Scale issues in soil hydrology related to measurement and simulation: A case study in Colorado

USDA-ARS?s Scientific Manuscript database

State variables, such as soil water content (SWC), are typically measured or inferred at very small scales while being simulated at larger scales relevant to spatial management or hillslope areas. Thus there is an implicit spatial disparity that is often ignored. Surface runoff, on the other hand, ...

32 CFR 935.136 - General operating rules.

Code of Federal Regulations, 2010 CFR

2010-07-01

... unposted area, except adjacent to the right-hand curb or edge of the road; (k) Park a motor vehicle in a... compacted surface; (n) Operate any motor vehicle contrary to a posted traffic sign; (o) Operate a motor... vehicle off of established roads, or in a cross-country manner, except when necessary in conducting...

32 CFR 935.136 - General operating rules.

Code of Federal Regulations, 2011 CFR

2011-07-01

... unposted area, except adjacent to the right-hand curb or edge of the road; (k) Park a motor vehicle in a... compacted surface; (n) Operate any motor vehicle contrary to a posted traffic sign; (o) Operate a motor... vehicle off of established roads, or in a cross-country manner, except when necessary in conducting...

32 CFR 935.136 - General operating rules.

Code of Federal Regulations, 2012 CFR

2012-07-01

... unposted area, except adjacent to the right-hand curb or edge of the road; (k) Park a motor vehicle in a... compacted surface; (n) Operate any motor vehicle contrary to a posted traffic sign; (o) Operate a motor... vehicle off of established roads, or in a cross-country manner, except when necessary in conducting...

32 CFR 935.136 - General operating rules.

Code of Federal Regulations, 2014 CFR

2014-07-01

... unposted area, except adjacent to the right-hand curb or edge of the road; (k) Park a motor vehicle in a... compacted surface; (n) Operate any motor vehicle contrary to a posted traffic sign; (o) Operate a motor... vehicle off of established roads, or in a cross-country manner, except when necessary in conducting...

32 CFR 935.136 - General operating rules.

Code of Federal Regulations, 2013 CFR

2013-07-01

... unposted area, except adjacent to the right-hand curb or edge of the road; (k) Park a motor vehicle in a... compacted surface; (n) Operate any motor vehicle contrary to a posted traffic sign; (o) Operate a motor... vehicle off of established roads, or in a cross-country manner, except when necessary in conducting...

Interaction between surface water areas and groundwater in Hanoi city, Viet Nam

NASA Astrophysics Data System (ADS)

Hayashi, T.; Kuroda, K.; Do Thuan, A.; Tran Thi Viet, N.; Takizawa, S.

2012-12-01

Hanoi is the capital of Viet Nam and the second largest city in this country (population: 6.45 million in 2009). Hanoi city has developed along the Red River and has many lakes, ponds and canals. However, recent rapid urbanization of this city has reduced number of natural water areas such as ponds and lakes by reclamation not only in the central area but the suburban area. Canals also have been reclaimed or cut into pieces. Contrary, number of artificial water areas such as fish cultivation pond has rapidly increased. On the other hand, various kind of waste water flows into these natural and artificial water areas and induces pollution and eutrophication. These waste waters also have possibility of pollution of groundwater that is one of major water resources in this city. In addition, groundwater in this area has high concentrations of Arsenic, Fe and NH4. Thus, groundwater use may causes re-circulation of Arsenic. However, studies on the interaction between surface water areas and groundwater and on the role of surface water areas for solute transport with water cycle are a few. Therefore, we focused on these points and took water samples of river, pond and groundwater from four communities in suburban areas: two communities are located near the Red River and other two are far from the River. Also, columnar sediment samples of these ponds were taken and pore water was abstracted. Major dissolved ions, metals and stable isotopes of oxygen and hydrogen of water samples were analyzed. As for water cycle, from the correlation between δ18O and δD, the Red River water (after GNIR) were distributed along the LMWL (δD=8.2δ18O+14.1, calculated from precipitation (after GNIP)). On the other hand, although the pond waters in rainy season were distributed along the LMWL, that in dry season were distributed along the local evaporation line (LEL, slope=5.6). The LEL crossed with the LMWL at around the point of weighted mean values of precipitation in rainy season and of the Red river. Groundwater samples were also distributed along the LEL and there was no seasonal change. Thus, groundwater in these communities was mainly recharged by mixing of precipitation/the Red River and evaporated water bodies. Considering the land use in these communities, evaporated water bodies were considered to be not only ponds but also paddy fields. As for solute transport, concentration of dissolved Arsenic (filtered by 0.45μm) of the pond water (3 - 10 μg/L) was slightly higher than the Red River (~ 3 μg/L) and was much lower than that of groundwater (~ 60 μg/L). On the other hand, concentration of dissolved Arsenic in the pore water of sediments (10 - 85 μg/L) was close to groundwater. Also, other metal elements showed the same trend. Therefore, Arsenic and other metal elements recharged to these ponds were considered to be adsorbed by sediments (including organic matters). That is, pond sediments played an important role as a filter of metal elements. The results of this study strongly suggested that the surface water areas such as ponds and paddy fields are one of main groundwater sources. Also, ponds play important role for solute transport of metal elements. Therefore, management of these surface water areas is important to conserve groundwater environment.

Heat loss through the glabrous skin surfaces of heavily insulated, heat-stressed individuals.

PubMed

Grahn, D A; Dillon, J L; Heller, H C

2009-07-01

Insulation reduces heat exchange between a body and the environment. Glabrous (nonhairy) skin surfaces (palms of the hands, soles of the feet, face, and ears) constitute a small percentage of total body surface area but contain specialized vascular structures that facilitate heat loss. We have previously reported that cooling the glabrous skin surfaces is effective in alleviating heat stress and that the application of local subatmospheric pressure enhances the effect. In this paper, we compare the effects of cooling multiple glabrous skin surfaces with and without vacuum on thermal recovery in heavily insulated heat-stressed individuals. Esophageal temperatures (T(es)) and heart rates were monitored throughout the trials. Water loss was determined from pre- and post-trial nude weights. Treadmill exercise (5.6 km/h, 9-16% slope, and 25-45 min duration) in a hot environment (41.5 degrees C, 20-30% relative humidity) while wearing insulating pants and jackets was used to induce heat stress (T(es)>or=39 degrees C). For postexercise recovery, the subjects donned additional insulation (a balaclava, winter gloves, and impermeable boot covers) and rested in the hot environment for 60 min. Postexercise cooling treatments included control (no cooling) or the application of a 10 degrees C closed water circulating system to (a) the hand(s) with or without application of a local subatmospheric pressure, (b) the face, (c) the feet, or (d) multiple glabrous skin regions. Following exercise induction of heat stress in heavily insulated subjects, the rate of recovery of T(es) was 0.4+/-0.2 degrees C/h(n=12), but with application of cooling to one hand, the rate was 0.8+/-0.3 degrees C/h(n=12), and with one hand cooling with subatmospheric pressure, the rate was 1.0+/-0.2 degrees C/h(n=12). Cooling alone yielded two responses, one resembling that of cooling with subatmospheric pressure (n=8) and one resembling that of no cooling (n=4). The effect of treating multiple surfaces was additive (no cooling, DeltaT(es)=-0.4+/-0.2 degrees C; one hand, -0.9+/-0.3 degrees C; face, -1.0+/-0.3 degrees C; two hands, -1.3+/-0.1 degrees C; two feet, -1.3+/-0.3 degrees C; and face, feet, and hands, -1.6+/-0.2 degrees C). Cooling treatments had a similar effect on water loss and final resting heart rate. In heat-stressed resting subjects, cooling the glabrous skin regions was effective in lowering T(es). Under this protocol, the application of local subatmospheric pressure did not significantly increase heat transfer per se but, presumably, increased the likelihood of an effect.

[Surface disinfection in the context of infection prevention in intensive care units].

PubMed

Kossow, A; Schaber, S; Kipp, F

2013-03-01

The highest proportion of nosocomial infections occurs on intensive care units (ICU) and infections with multiresistant pathogens are an ever increasing problem. Preventative measures should consist of a bundle of different measures including measures that address a specific problem and standard hygiene measures that are relevant in all areas. Specific measures in ICUs primarily aim at the prevention of ventilator associated pneumonia, blood vessel catheter associated infections and nosocomial urinary tract infections. Surface disinfection belongs to the standard hygiene measures and plays an inferior role compared to hand hygiene; however, surfaces come into focus in outbreak situations. The Commission on Hospital Hygiene (KRINKO) at the Robert Koch Institute (the German health protection agency) published recommendations regarding the cleaning and disinfection of surfaces. The frequency with which cleaning and/or disinfection is required varies according to defined areas of risk. The frequency and the disinfection agents used are documented in the disinfection plan.

Afforestation contribution to Carbon and Nitrogen budgets of forest in a natural park in south Spain

NASA Astrophysics Data System (ADS)

Lozano-García, Beatriz; Parras-Alcántara, Luis

2015-04-01

Forests are important ecosystems because they provide wood products to society as well as many services (recreation, habitat functions, the regulation of water, erosion, and air quality). However, the society has recently focused its attention on forests for two reasons; sequestration of carbon, on the one hand, and provision of biomass for bioenergy, on the other, also illustrates the possible trade-off even within the theme of climate change mitigation. Due to this fact, the forest surface has increased in Spain, as well in Europe in the last decades. The area covered by forest represents 34% in Europe and 35.6% in Spain compared to the total surface. A powerful afforestation policy was carried out in Spain from the 40's decade in forward. The main objective was to increase the forest surface with trees. Two main actions were developed under these repopulations, the transformation of pasture land in forest, on the one hand, and the introduction of fast-growing tree species, on the second hand. Therefore, currently, there are a lot of forest areas in Spain in which the introduced species coexist with native. In addition, the spatial variation of soil properties is significantly influenced by some environmental factors such as topographic aspect that induced microclimate differences, topographic (landscape) positions, parent materials, and vegetation communities. Topographic aspect induces local variation in temperature and precipitation solar radiation and relative humidity, which along with chemical and physical composition of the substrate, are the main regulators of decomposition rates of organic matter. The aim of this study were, i) to evaluate the effect of afforestation policies on carbon and nitrogen budgets in a natural park in Spain and ii) to study the topographic aspect effect on the capacity of SOC and N storage. Our results show how the afforestated areas (in which there are simultaneously both, natural species and introduced species) had higher soil organic carbon (SOC) and nitrogen (N) concentrations and SOC and N stocks than the natural areas.

Thermal infrared imagery as a tool for analysing the variability of surface saturated areas at various temporal and spatial scales

NASA Astrophysics Data System (ADS)

Glaser, Barbara; Antonelli, Marta; Pfister, Laurent; Klaus, Julian

2017-04-01

Surface saturated areas are important for the on- and offset of hydrological connectivity within the hillslope-riparian-stream continuum. This is reflected in concepts such as variable contributing areas or critical source areas. However, we still lack a standardized method for areal mapping of surface saturation and for observing its spatiotemporal variability. Proof-of-concept studies in recent years have shown the potential of thermal infrared (TIR) imagery to record surface saturation dynamics at various temporal and spatial scales. Thermal infrared imagery is thus a promising alternative to conventional approaches, such as the squishy boot method or the mapping of vegetation. In this study we use TIR images to investigate the variability of surface saturated areas at different temporal and spatial scales in the forested Weierbach catchment (0.45 km2) in western Luxembourg. We took TIR images of the riparian zone with a hand-held FLIR infrared camera at fortnightly intervals over 18 months at nine different locations distributed over the catchment. Not all of the acquired images were suitable for a derivation of the surface saturated areas, as various factors influence the usability of the TIR images (e.g. temperature contrasts, shadows, fog). Nonetheless, we obtained a large number of usable images that provided a good insight into the dynamic behaviour of surface saturated areas at different scales. The images revealed how diverse the evolution of surface saturated areas can be throughout the hydrologic year. For some locations with similar morphology or topography we identified diverging saturation dynamics, while other locations with different morphology / topography showed more similar behaviour. Moreover, we were able to assess the variability of the dynamics of expansion / contraction of saturated areas within the single locations, which can help to better understand the mechanisms behind surface saturation development.

The effect of a manual instrumentation technique on five types of premolar root canal geometry assessed by microcomputed tomography and three-dimensional reconstruction

PubMed Central

2011-01-01

Background Together with diagnosis and treatment planning, a good knowledge of the root canal system and its frequent variations is a necessity for successful root canal therapy. The selection of instrumentation techniques for variants in internal anatomy of teeth has significant effects on the shaping ability and cleaning effectiveness. The aim of this study was to reveal the differences made by including variations in the internal anatomy of premolars into the study protocol for investigation of a single instrumentation technique (hand ProTaper instruments) assessed by microcomputed tomography and three-dimensional reconstruction. Methods Five single-root premolars, whose root canal systems were classified into one of five types, were scanned with micro-CT before and after preparation with a hand ProTaper instrument. Instrumentation characteristics were measured quantitatively in 3-D using a customized application framework based on MeVisLab. Numeric values were obtained for canal surface area, volume, volume changes, percentage of untouched surface, dentin wall thickness, and the thickness of dentin removed. Preparation errors were also evaluated using a color-coded reconstruction. Results Canal volumes and surface areas were increased after instrumentation. Prepared canals of all five types were straightened, with transportation toward the inner aspects of S-shaped or multiple curves. However, a ledge was formed at the apical third curve of the type II canal system and a wide range in the percentage of unchanged canal surfaces (27.4-83.0%) was recorded. The dentin walls were more than 0.3 mm thick except in a 1 mm zone from the apical surface and the hazardous area of the type II canal system after preparation with an F3 instrument. Conclusions The 3-D color-coded images showed different morphological changes in the five types of root canal systems shaped with the same hand instrumentation technique. Premolars are among the most complex teeth for root canal treatment and instrumentation techniques for the root canal systems of premolars should be selected individually depending on the 3-D canal configuration of each tooth. Further study is needed to demonstrate the differences made by including variations in the internal anatomy of teeth into the study protocol of clinical RCT for identifying the best preparation technique. PMID:21676233

Thin film passivation of laser generated 3D micro patterns in lithium manganese oxide cathodes

NASA Astrophysics Data System (ADS)

Pröll, J.; Kohler, R.; Bruns, M.; Oberst, V.; Weidler, P. G.; Heißler, S.; Kübel, C.; Scherer, T.; Prang, R.; Seifert, H. J.; Pfleging, W.

2013-03-01

The increasing need for long-life lithium-ion batteries requires the further development of electrode materials. Especially on the cathode side new materials or material composites are needed to increase the cycle lifetime. On the one hand, spinel-type lithium manganese oxide is a promising candidate to be used as cathode material due to its non-toxicity, low cost and good thermal stability. On the other hand, the spinel structure suffers from change in the oxidation state of manganese during cycling which is also accompanied by loss of active material into the liquid electrolyte. The general trend is to enhance the active surface area of the cathode in order to increase lithium-ion mobility through the electrode/electrolyte interface, while an enhanced surface area will also promote chemical degradation. In this work, laser microstructuring of lithium manganese oxide thin films was applied in a first step to increase the active surface area. This was done by using 248 nm excimer laser radiation and chromium/quartz mask imaging techniques. In a second step, high power diode laser-annealing operating at a wavelength of 940 nm was used for forming a cubic spinel-like battery phase. This was verified by means of Raman spectroscopy and cyclic voltammetric measurements. In a last step, the laser patterned thin films were coated with indium tin oxide (ITO) layers with a thickness of 10 nm to 50 nm. The influence of the 3D surface topography as well as the ITO thickness on the electrochemical performance was studied by cyclic voltammetry. Post-mortem studies were carried out by using scanning electron microscopy and focused ion beam analysis.

Environmental DNA method for estimating salamander distribution in headwater streams, and a comparison of water sampling methods.

PubMed

Katano, Izumi; Harada, Ken; Doi, Hideyuki; Souma, Rio; Minamoto, Toshifumi

2017-01-01

Environmental DNA (eDNA) has recently been used for detecting the distribution of macroorganisms in various aquatic habitats. In this study, we applied an eDNA method to estimate the distribution of the Japanese clawed salamander, Onychodactylus japonicus, in headwater streams. Additionally, we compared the detection of eDNA and hand-capturing methods used for determining the distribution of O. japonicus. For eDNA detection, we designed a qPCR primer/probe set for O. japonicus using the 12S rRNA region. We detected the eDNA of O. japonicus at all sites (with the exception of one), where we also observed them by hand-capturing. Additionally, we detected eDNA at two sites where we were unable to observe individuals using the hand-capturing method. Moreover, we found that eDNA concentrations and detection rates of the two water sampling areas (stream surface and under stones) were not significantly different, although the eDNA concentration in the water under stones was more varied than that on the surface. We, therefore, conclude that eDNA methods could be used to determine the distribution of macroorganisms inhabiting headwater systems by using samples collected from the surface of the water.

Global 30m Height Above the Nearest Drainage

NASA Astrophysics Data System (ADS)

Donchyts, Gennadii; Winsemius, Hessel; Schellekens, Jaap; Erickson, Tyler; Gao, Hongkai; Savenije, Hubert; van de Giesen, Nick

2016-04-01

Variability of the Earth surface is the primary characteristics affecting the flow of surface and subsurface water. Digital elevation models, usually represented as height maps above some well-defined vertical datum, are used a lot to compute hydrologic parameters such as local flow directions, drainage area, drainage network pattern, and many others. Usually, it requires a significant effort to derive these parameters at a global scale. One hydrological characteristic introduced in the last decade is Height Above the Nearest Drainage (HAND): a digital elevation model normalized using nearest drainage. This parameter has been shown to be useful for many hydrological and more general purpose applications, such as landscape hazard mapping, landform classification, remote sensing and rainfall-runoff modeling. One of the essential characteristics of HAND is its ability to capture heterogeneities in local environments, difficult to measure or model otherwise. While many applications of HAND were published in the academic literature, no studies analyze its variability on a global scale, especially, using higher resolution DEMs, such as the new, one arc-second (approximately 30m) resolution version of SRTM. In this work, we will present the first global version of HAND computed using a mosaic of two DEMS: 30m SRTM and Viewfinderpanorama DEM (90m). The lower resolution DEM was used to cover latitudes above 60 degrees north and below 56 degrees south where SRTM is not available. We compute HAND using the unmodified version of the input DEMs to ensure consistency with the original elevation model. We have parallelized processing by generating a homogenized, equal-area version of HydroBASINS catchments. The resulting catchment boundaries were used to perform processing using 30m resolution DEM. To compute HAND, a new version of D8 local drainage directions as well as flow accumulation were calculated. The latter was used to estimate river head by incorporating fixed and variable thresholding methods. The resulting HAND dataset was analyzed regarding its spatial variability and to assess the global distribution of the main landform types: valley, ecotone, slope, and plateau. The method used to compute HAND was implemented using PCRaster software, running on Google Compute Engine platform running under Ubuntu Linux. The Google Earth Engine was used to perform mosaicing and clipping of the original DEMs as well as to provide access to the final product. The effort took about three months of computing time on eight core CPU virtual machine.

ARC-1979-AC79-7081

NASA Image and Video Library

1979-07-08

P-21747 C Range: 2,200,000 miles This image shows a region of the Jovian atmosphere from approximately 25° N to the equatorial region. The north temperate jet, at approximately 23° N, where the wind speed is about 150 meters per second, is seen as a dark brown line from the left-hand edge to the right-hand corner of the picture. The wispy clouds of the north equatorial belt appear as shades of brown. The lower right-hand corner of the image shows the brighter (white) clouds of the equatorial region. A small blue area is apparent near the lower edge, which corresponds to a region free of the upper clouds, where it is possible to penetrate to cloud layers approximately 60 kilometers below the visible surface.

ARC-1979-A79-7081

NASA Image and Video Library

1979-07-08

P-21747 BW Range: 2,200,000 miles This image shows a region of the Jovian atmosphere from approximately 25° N to the equatorial region. The north temperate jet, at approximately 23° N, where the wind speed is about 150 meters per second, is seen as a dark brown line from the left-hand edge to the right-hand corner of the picture. The wispy clouds of the north equatorial belt appear as shades of brown. The lower right-hand corner of the image shows the brighter (white) clouds of the equatorial region. A small blue area is apparent near the lower edge, which corresponds to a region free of the upper clouds, where it is possible to penetrate to cloud layers approximately 60 kilometers below the visible surface.

Comparing activated alumina with indigenous laterite and bauxite as potential sorbents for removing fluoride from drinking water in Ghana

USGS Publications Warehouse

Craig, Laura; Stillings, Lisa; Decker, David L.; Thomas, James M.

2015-01-01

Fluoride is considered beneficial to teeth and bones when consumed in low concentrations, but at elevated concentrations it can cause dental and skeletal fluorosis. Most fluoride-related health problems occur in poor, rural communities of the developing world where groundwater fluoride concentrations are high and the primary sources of drinking water are from community hand-pump borehole drilled wells. One solution to drinking high fluoride water is to attach a simple de-fluoridation filter to the hand-pump; and indigenous materials have been recommended as low-cost sorbents for use in these filters. In an effort to develop an effective, inexpensive, and low-maintenance de-fluoridation filter for a high fluoride region in rural northern Ghana, this study conducted batch fluoride adsorption experiments and potentiometric titrations to investigate the effectiveness of indigenous laterite and bauxite as sorbents for fluoride removal. It also determined the physical and chemical properties of each sorbent. Their properties and the experimental results, including fluoride adsorption capacity, were then compared to those of activated alumina, which has been identified as a good sorbent for removing fluoride from drinking water. The results indicate that, of the three sorbents, bauxite has the highest fluoride adsorption capacity per unit area, but is limited by a low specific surface area. When considering fluoride adsorption per unit weight, activated alumina has the highest fluoride adsorption capacity because of its high specific surface area. Activated alumina also adsorbs fluoride well in a wider pH range than bauxite, and particularly laterite. The differences in adsorption capacity are largely due to surface area, pore size, and mineralogy of the sorbent.

Life begins when the sea lion is ashore: microhabitat use by a louse living on a diving mammal host.

PubMed

Leonardi, M S; Crespo, E A; Vales, D G; Feijoo, M; Raga, J A; Aznar, F J

2012-08-01

Among Anoplura, the family Echinophthiriidae includes species that infest pinnipeds and otters. Previous evidence obtained from pinnipeds infested by echinophthiriids, specifically from seals, indicates that flippers are the preferred infestation sites, while lice from fur seals select areas in the pelage. We studied habitat selection of Antarctophthirus microchir on South American sea lion pups (Otaria flavescens Shaw, 1800) from Patagonia, Argentina, during the austral summer of 2009. We found a clear pattern of habitat selection: eggs are laid on the dorsal surface; nymphs 1 hatch there and then migrate to the belly, where they develop into adults and copulate; and then ovigerous females return to the dorsal surface. On the one hand, nymphs 1 are characterised by their low locomotory ability; therefore, the fact that they migrate as soon as they hatch suggests a clear pressure leading to microhabitat restriction. On the other hand, the described pattern of microhabitat selection seems to respond to the physiological requirements of each stage, which vary according to the physiological process considered, e.g. oviposition, morphogenesis, hatching and development. Accordingly, it appears that A. microchir would prefer the host's ventral area for development and copulation and the dorsal area for oviposition. However, the causes of this pattern are not clear, and many factors could be involved. Considering that sea lion pups periodically soak at high tides, and that prolonged immersion and very high humidity are known to be lethal for lice eggs, selecting the dorsal area would be advantageous for oviposition because it dries much faster. Furthermore, because humidity should be retained for longer periods on the ventral surface of the pup, wetter conditions on the sea lion would prevent desiccation of the nymphs in the very arid environment where O. flavescens breeds.

Thermal Imaging of Body Surface Temperature Distribution in Women with Anorexia Nervosa.

PubMed

Chudecka, Monika; Lubkowska, Anna

2016-01-01

The drastic reduction in body weight observed in anorexia nervosa (AN) leads to various endocrine changes and consequently to disturbance in thermoregulation mechanisms and body temperature. Thermography allows for a noninvasive diagnosis of the distribution of skin surface temperatures, which is especially important for difficult patients such as women with AN, who are often very sensitive and difficult to treat. The main aim of this study was to measure the mean temperatures (Tmean ) of selected body areas in young women diagnosed with AN and identify those areas where the temperature differences were particularly significant between healthy women and them. Additionally, we determined the relationships between body mass index, body composition (especially subcutaneous and VFM) and the value of mean surface temperature (Tmean ) in AN woman. In the subjects with AN, Tmean of the abdomen, lower back and thighs were significantly higher than in the reference group, while Tmean of the hands were significantly lower. Among other things, analysis showed a significant negative correlation between Tmean of the abdomen, lower back and thighs, and the mass of subcutaneous and visceral fat. The lower Tmean of the hand was directly proportional to the reduced anthropomorphic parameters. The direct evaluation of body surface temperature distribution could provide clinical implications for the treatment of anorexic patients, including the potential use of thermotherapy in stimulating the circulatory system, especially in hypothermia, bradycardia and hypotension. Copyright © 2015 John Wiley & Sons, Ltd and Eating Disorders Association.

Hyperbaric gaseous cryotherapy: effects on skin temperature and systemic vasoconstriction.

PubMed

Mourot, Laurent; Cluzeau, Christian; Regnard, Jacques

2007-10-01

To compare skin-surface cooling caused by the application of an ice bag (15min) and the projection of carbon dioxide microcristals (2min) under high pressure (75 bar) and low temperature (-78 degrees C), a modality called hyperbaric gaseous cryotherapy. Randomized controlled trial with repeated measure. Laboratory experiment. Twelve healthy male subjects (mean +/- standard deviation, 22.9+/-1.8y). Ice bag and hyperbaric gaseous cryotherapy were randomly applied on the skin of the nondominant hand. Skin temperature of the cooled (dorsal and palmar sides) and contralateral (dorsal side) hands were continuously measured with thermistor surface-contact probes before, during, and after (30min) cooling. Hyperbaric gaseous cryotherapy projection induced a large decrease (P<.05) of the dorsal skin temperature of the cooled hand (from 32.5 degrees +/-0.5 degrees C to 7.3 degrees +/-0.8 degrees C) and a significant decrease of the skin temperature of the palmar side and of the contralateral hand. The skin temperature of the dorsal side of the cooled hand was decreased with an ice bag (from 32.5 degrees +/-0.6 degrees C to 13.9 degrees +/-0.7 degrees C, P<.05). However, the lowest temperature was significantly higher than during hyperbaric gaseous cryotherapy, and no significant changes in the other skin temperatures were observed. Rewarming was equal after the 2 modalities, highlighting a more rapid increase of the skin temperature after hyperbaric gaseous cryotherapy. Hyperbaric gaseous cryotherapy projection decreased the skin temperature of the cooled and contralateral hand, suggesting a systemic skin vasoconstriction response. On the other hand, the vascular responses triggered by ice pack cooling appeared limited and localized to the cooled area.

Thermal and Mechanical Testing of Neoprene Gloves Used in a Space Shuttle Microgravity Glove Box Experiment

NASA Technical Reports Server (NTRS)

Wingard, Charles Doug; Munafo, Paul M. (Technical Monitor)

2001-01-01

Neoprene gloves are used in a Space Shuttle Microgravity Glove Box (MGBX) experiment. In 1999, significant corrosion was observed in the work area and on the outer surface of the left glove ring. Analysis of the corrosion products showed that they contained chlorine. The Neoprene gloves used in this glove box were obtained in 1995, with a recommended shelf life of 3 years. After storage of these gloves in a cabinet drawer until 1999, significant signs of corrosion were also observed in the drawer. Mechanical and thermal properties were determined on samples cut from the finger and sleeve areas of the "good" and "bad" gloves. This data showed significant aging of the left-hand glove, particularly in the sleeve area. Thermal analysis data by DSC and TGA was complimentary to tensile data in showing this aging. However, this test data did not pinpoint the cause of the left-hand glove aging, or of the corrosion products.

Heat transfer from an oxidized large copper surface to liquid helium: Dependence on surface orientation and treatment

DOE Office of Scientific and Technical Information (OSTI.GOV)

Iwamoto, A.; Mito, T.; Takahata, K.

Heat transfer of large copper plates (18 x 76 mm) in liquid helium has been measured as a function of orientation and treatment of the heat transfer surface. The results relate to applications of large scale superconductors. In order to clarify the influence of the area where the surface treatment peels off, the authors studied five types of heat transfer surface areas including: (a) 100% polished copper sample, (b) and (c) two 50% oxidized copper samples having different patterns of oxidation, (d) 75% oxidized copper sample, (e) 90% oxidized copper sample, and (f) 100% oxidized copper sample. They observed thatmore » the critical heat flux depends on the heat transfer surface orientation. The critical heat flux is a maximum at angles of 0{degrees} - 30{degrees} and decreases monotonically with increasing angles above 30{degrees}, where the angle is taken in reference to the horizontal axis. On the other hand, the minimum heat flux is less dependent on the surface orientation. More than 75% oxidation on the surface makes the critical heat flux increase. The minimum heat fluxes of the 50 and 90% oxidized Cu samples approximately agree with that of the 100% oxidized Cu sample. Experiments and calculations show that the critical and the minimum heat fluxes are a bilinear function of the fraction of oxidized surface area.« less

Human body surface area database and estimation formula.

PubMed

Yu, Chi-Yuang; Lin, Ching-Hua; Yang, Yi-Hsueh

2010-08-01

This study established human body surface area (BSA) database and estimation formula based on three-dimensional (3D) scanned data. For each gender, 135 subjects were drawn. The sampling was stratified in five stature heights and three body weights according to a previous survey. The 3D body surface shape was measured using an innovated 3D body scanner and a high resolution hand/foot scanner, the total body surface area (BSA) and segmental body surface area (SBSA) were computed based on the summation of every tiny triangular area of triangular meshes of the scanned surface; and the accuracy of BSA measurement is below 1%. The results of BSA and sixteen SBSAs were tabulated in fifteen strata for the Male, the Female and the Total (two genders combined). The %SBSA data was also used to revise new Lund and Browder Charts. The comparison of BSA shows that the BSA of this study is comparable with the Du Bois and Du Bois' but smaller than that of Tikuisis et al. The difference might be attributed to body size difference between the samples. The comparison of SBSA shows that the differences of SBSA between this study and the Lund and Browder Chart range between 0.00% and 2.30%. A new BSA estimation formula, BSA=71.3989 x H(.7437) x W(.4040), was obtained. An accuracy test showed that this formula has smaller estimation error than that of the Du Bois and Du Bois'; and significantly better than other BSA estimation formulae.

Associations between site of skin lesions and depression, social anxiety, body-related emotions and feelings of stigmatization in psoriasis patients.

PubMed

Łakuta, Patryk; Marcinkiewicz, Kamil; Bergler-Czop, Beata; Brzezińska-Wcisło, Ligia; Słomian, Anna

2018-02-01

Research has demonstrated a link between psoriasis and a multitude of psychological impairments; however, relatively few studies have examined the importance of site of skin lesions for negative psychological outcomes in psoriasis patients. To investigate relationships between anatomical location of psoriatic lesions and experiences of stigmatization, negative emotional attitude towards the body, depression and social anxiety. Adult psoriasis patients ( N = 193) completed the Stigmatization Scale, the Body Emotions Scale, the Beck Depression Inventory and the Social Anxiety Questionnaire. The body surface area index was used to assess the location and extent of psoriasis. Feelings of stigmatization were found to be most closely related to the presence of psoriatic lesions on the chest, and the arms and hands. Higher levels of social anxiety were found to be most closely related to the location of psoriatic lesions on the head and neck. Negative emotional attitude towards the body was found to be most closely related to the location of psoriatic lesions on the arms and hands, and on the head and neck. Higher levels of depressive symptoms were most closely related to the presence of psoriatic lesions on the head and neck, the arms and hands, and the genital area. The presence of psoriatic lesions on the head, neck, and chest, and also on the arms and hands and the genital area, should alert clinicians to a higher risk of psychological impairments. This may help to better recognize and prevent cumulative life course impairment.

Micro-computed tomographic comparison of nickel-titanium rotary versus traditional instruments in C-shaped root canal system.

PubMed

Yin, Xingzhe; Cheung, Gary Shun-Pan; Zhang, Chengfei; Masuda, Yoshiko Murakami; Kimura, Yuichi; Matsumoto, Koukichi

2010-04-01

The purpose of this study was to assess the efficacy of instrumentation of C-shaped canals with ProTaper rotary system and traditional instruments by using micro-computed tomography (micro-CT). Twenty-four mandibular molars with C-shaped canals were selected in pairs and sorted equally into 2 groups, which were assigned for instrumentation by ProTaper rotary system (ProTaper group) or by K-files and Gates-Glidden burs (Hand Instrument group). Three-dimensional images were constructed by micro-CT. The volume of dentin removed, uninstrumented canal area, time taken for instrumentation, and iatrogenic error of instrumentation were investigated. Hand Instrument group showed greater amount of volumetric dentin removal and left less uninstrumented canal area than ProTaper group (P < .01). The time needed for instrumentation was shorter for ProTaper group than for Hand Instrument group (P < .05). No instrument breakage occurred in both groups, but more conspicuous procedural errors were detected in Hand Instrument group than for ProTaper group. It was concluded that ProTaper rotary system maintained the canal curvature with speediness and few procedural errors, whereas traditional instrumentation can clean more canal surface. Copyright (c) 2010 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

A 3D quantitative comparison of trapezium and trapezoid relative articular and nonarticular surface areas in modern humans and great apes.

PubMed

Tocheri, M W; Razdan, A; Williams, R C; Marzke, M W

2005-11-01

The structure and functions of the modern human hand are critical components of what distinguishes Homo sapiens from the great apes (Gorilla, Pan, and Pongo). In this study, attention is focused on the trapezium and trapezoid, the two most lateral bones of the distal carpal row, in the four extant hominid genera, representing the first time they have been quantified and analyzed together as a morphological-functional complex. Our objective is to quantify the relative articular and nonarticular surface areas of these two bones and to test whether modern humans exhibit significant shape differences from the great apes, as predicted by previous qualitative analyses and the functional demands of differing manipulative and locomotor strategies. Modern humans were predicted to show larger relative first metacarpal and scaphoid surfaces on the trapezium because of the regular recruitment of the thumb during manipulative behaviors; alternatively, great apes were predicted to show larger relative second metacarpal and scaphoid surfaces on the trapezoid because of the functional demands on the hands during locomotor behaviors. Modern humans were also expected to exhibit larger relative mutual joint surfaces between the trapezoid and adjacent carpals than do the great apes because of assumed transverse loads generated by the functional demands of the modern human power grip. Using 3D bone models acquired through laser digitizing, the relative articular and nonarticular areas on each bone are quantified and compared. Multivariate analyses of these data clearly distinguish modern humans from the great apes. In total, the observed differences between modern humans and the great apes support morphological predictions based on the fact that this region of the human wrist is no longer involved in weight-bearing during locomotor behavior and is instead recruited solely for manipulative behaviors. The results provide the beginnings of a 3D comparative standard against which further extant and fossil primate wrist bones can be compared within the contexts of manipulative and locomotor behaviors.

Evaluating climatic and non-climatic stresses for declining surface water quality in Bagmati River of Nepal.

PubMed

Panthi, Jeeban; Li, Fengting; Wang, Hongtao; Aryal, Suman; Dahal, Piyush; Ghimire, Sheila; Kabenge, Martin

2017-06-01

Both climatic and non-climatic factors affect surface water quality. Similar to its effect across various sectors and areas, climate change has potential to affect surface water quality directly and indirectly. On the one hand, the rise in temperature enhances the microbial activity and decomposition of organic matter in the river system and changes in rainfall alter discharge and water flow in the river ultimately affecting pollution dilution level. On the other hand, the disposal of organic waste and channelizing municipal sewage into the rivers seriously worsen water quality. This study attempts to relate hydro-climatology, water quality, and impact of climatic and non-climatic stresses in affecting river water quality in the upper Bagmati basin in Central Nepal. The results showed that the key water quality indicators such as dissolved oxygen and chemical oxygen demand are getting worse in recent years. No significant relationships were found between the key water quality indicators and changes in key climatic variables. However, the water quality indicators correlated with the increase in urban population and per capita waste production in the city. The findings of this study indicate that dealing with non-climatic stressors such as reducing direct disposal of sewerage and other wastes in the river rather than emphasizing on working with the effects from climate change would largely help to improve water quality in the river flowing from highly populated urban areas.

Lithium and sodium ion capacitors with high energy and power densities based on carbons from recycled olive pits

NASA Astrophysics Data System (ADS)

Ajuria, Jon; Redondo, Edurne; Arnaiz, Maria; Mysyk, Roman; Rojo, Teófilo; Goikolea, Eider

2017-08-01

In this work, we are presenting both lithium and sodium ion capacitors (LIC and NIC) entirely based on electrodes designed from recycled olive pit bio-waste derived carbon materials. On the one hand, olive pits were pyrolized to obtain a low specific surface area semigraphitic hard carbon to be used as the ion intercalation (battery-type) negative electrode. On the other hand, the same hard carbon was chemically activated with KOH to obtain a high specific surface area activated carbon that was further used as the ion-adsorption (capacitor-type) positive electrode. Both electrodes were custom-made to be assembled in a hybrid cell to either build a LIC or NIC in the corresponding Li- and Na-based electrolytes. For comparison purposes, a symmetric EDLC supercapacitor cell using the same activated carbon in 1.5 M Et4NBF4/acetonitrile electrolyte was also built. Both LIC and NIC systems demonstrate remarkable energy and power density enhancement over its EDLC counterpart while showing good cycle life. This breakthrough offers the possibility to easily fabricate versatile hybrid ion capacitors, covering a wide variety of applications where different requirements are demanded.

Synthesis of Porous Carbon Monoliths Using Hard Templates.

PubMed

Klepel, Olaf; Danneberg, Nina; Dräger, Matti; Erlitz, Marcel; Taubert, Michael

2016-03-21

The preparation of porous carbon monoliths with a defined shape via template-assisted routes is reported. Monoliths made from porous concrete and zeolite were each used as the template. The porous concrete-derived carbon monoliths exhibited high gravimetric specific surface areas up to 2000 m²·g -1 . The pore system comprised macro-, meso-, and micropores. These pores were hierarchically arranged. The pore system was created by the complex interplay of the actions of both the template and the activating agent as well. On the other hand, zeolite-made template shapes allowed for the preparation of microporous carbon monoliths with a high volumetric specific surface area. This feature could be beneficial if carbon monoliths must be integrated into technical systems under space-limited conditions.

Synthesis of Porous Carbon Monoliths Using Hard Templates

PubMed Central

Klepel, Olaf; Danneberg, Nina; Dräger, Matti; Erlitz, Marcel; Taubert, Michael

2016-01-01

The preparation of porous carbon monoliths with a defined shape via template-assisted routes is reported. Monoliths made from porous concrete and zeolite were each used as the template. The porous concrete-derived carbon monoliths exhibited high gravimetric specific surface areas up to 2000 m2·g−1. The pore system comprised macro-, meso-, and micropores. These pores were hierarchically arranged. The pore system was created by the complex interplay of the actions of both the template and the activating agent as well. On the other hand, zeolite-made template shapes allowed for the preparation of microporous carbon monoliths with a high volumetric specific surface area. This feature could be beneficial if carbon monoliths must be integrated into technical systems under space-limited conditions. PMID:28773338

Assessment of the environmental microbiological cross contamination following hand drying with paper hand towels or an air blade dryer.

PubMed

Margas, E; Maguire, E; Berland, C R; Welander, F; Holah, J T

2013-08-01

This study compared the potential for cross contamination of the surrounding environment resulting from two different hand-drying methods: paper towels and the use of an air blade dryer. One hundred volunteers for each method washed their hands and dried them using one of the two methods. Bacterial contamination of the surrounding environment was measured using settle plates placed on the floor in a grid pattern, air sampling and surface swabs. Both drying methods produced ballistic droplets in the immediate vicinity of the hand-drying process. The air blade dryer produced a larger number of droplets which were dispersed over a larger area. Settle plates showed increased microbial contamination in the grid squares which were affected by ballistic droplets. Using the settle plates counts, it was estimated that approx. 1.7 × 10(5) cfu more micro-organisms were left on the laboratory floor (total area approx. 17.15 m(2)) after 100 volunteers used an air blade dryer compared to when paper towels were used. The two drying methods led to different patterns of ballistic droplets and levels of microbial contamination under heavy use conditions. Whilst the increase in microbial levels in the environment is not significant if only nonpathogenic micro-organisms are spread, it may increase the risk of pathogen contamination of the environment when pathogens are occasionally present on people's hands. The study suggests that the risk of cross contamination from the washroom users to the environment and subsequent users should be considered when choosing a hand-drying method. The data could potentially give guidance following the selection of drying methods on implementing measures to minimise the risk of cross contamination. © 2013 The Society for Applied Microbiology.

Transfer rates of enteric microorganisms in recycled water during machine clothes washing.

PubMed

O'Toole, Joanne; Sinclair, Martha; Leder, Karin

2009-03-01

Approximately 15% of overall Australian household water usage is in the laundry; hence, a significant reduction in household drinking water demand could be achieved if potable-quality water used for clothes washing is replaced with recycled water. To investigate the microbiological safety of using recycled water in washing machines, bacteriophages MS-2 and PRD-1, Escherichia coli, and Cryptosporidium parvum oocysts were used in a series of experiments to investigate the transfer efficiency of enteric microorganisms from washing machine water to objects including hands, environmental surfaces, air, and fabric swatches. By determining the transference efficiency, it is possible to estimate the numbers of microorganisms that the user will be exposed to if recycled water with various levels of residual microorganisms is used in washing machines. Results, expressed as transfer rates to a given surface area per object, showed that the mean transfer efficiency of E. coli, bacteriophages MS-2 and PRD-1, and C. parvum oocysts from seeded water to fabric swatches ranged from 0.001% to 0.090%. Greatest exposure to microorganisms occurred through direct contact of hands with seeded water and via hand contact with contaminated fabric swatches. No microorganisms were detected in the air samples during the washing machine spin cycle, and transfer rates of bacteriophages from water to environmental surfaces were 100-fold less than from water directly to hands. Findings from this study provide relevant information that can be used to refine regulations governing recycled water and to allay public concerns about the use of recycled water.

Femtosecond laser-induced periodic surface structures on titanium nitride coatings for tribological applications

NASA Astrophysics Data System (ADS)

Bonse, J.; Kirner, S. V.; Koter, R.; Pentzien, S.; Spaltmann, D.; Krüger, J.

2017-10-01

Titanium nitride (TiN) was coated on different substrate materials, namely pure titanium (Ti), titanium alloy (Ti6Al4V) and steel (100Cr6), generating 2.5 μm thick TiN layers. Using femtosecond laser pulses (30 fs, 790 nm, 1 kHz pulse repetition rate), large surface areas (5 mm × 5 mm) of laser-induced periodic surface structures (LIPSS) with sub-wavelength periods ranging between 470 nm and 600 nm were generated and characterized by optical microscopy (OM), white light interference microscopy (WLIM) and scanning electron microscopy (SEM). In tribological tests, coefficients of friction (COF) of the nanostructured surfaces were determined under reciprocating sliding conditions (1 Hz, 1.0 N normal load) against a 10-mm diameter ball of hardened 100Cr6 steel during 1000 cycles using two different lubricants, namely paraffin oil and engine oil. It turned out that the substrate material, the laser fluence and the lubricant are crucial for the tribological performance. However, friction and wear could not be significantly reduced by LIPSS on TiN layers in comparison to unstructured TiN surfaces. Finally, the resulting wear tracks on the nanostructured surfaces were investigated with respect to their morphology (OM, SEM), depth (WLIM) and chemical composition by energy dispersive X-ray spectroscopy (EDX) and, on one hand, compared with each other, on the other hand, with non-structured TiN surfaces.

A simple method for estimation of evapotranspiration using remotely sensed data during vegetation period in Hungary

NASA Astrophysics Data System (ADS)

Dunkel, Zoltan; Grob-Szenyán, Ildiko

The surface temperature measured by satellite can be the basis of evapotranspiration (ET) computation. The possibility of the daily sum of the regional ET using surface temperature was examined under Hungarian weather conditions. A simplified relationship, namely ET d-R nd= a+ b( Tc- Ta), which relates the daily ET to daily net radiation with one measurements of surface and air temperature was used for the calculation. Using NOAA AVHRR satellite data, no information about the surface inhomogeneity was obtained. The distribution of surface temperature was investigated by infrared thermometer scanning the surface from a board a hang-glider, ultra-light-aeroplane, and light aeroplane. Field observations trials were made during the vegetation period of 1992, 1993, 1994 and 1995. In eastern part of the country a homogeneous field ( 1 km×1 km) and a larger, and relatively homogeneous area was scanned, before noon and afternoon. In the western part of the country, a much larger area ( 45 km×45 km) was investigated. Cultivated area, forest and a large water surface were included in the investigated surface. The problems of calibration of hand-held infrared thermometer and the time shifting are discussed. Comparison of model output with data from field experiment has played a crucial role in model development and suggested an evaluation method.

Drug release through liposome pores.

PubMed

Dan, Nily

2015-02-01

Electrical, ultrasound and other types of external fields are known to induce the formation of pores in cellular and model membranes. This paper examines drug release through field induced liposome pores using Monte Carlo simulations. We find that drug release rates vary as a function of pore size and spacing, as well as the overall fraction of surface area covered by pores: The rate of release from liposomes is found to increase rapidly with pore surface coverage, approaching that of the fully ruptured liposome at fractional pore areas. For a given pore surface coverage, the pore size affects the release rate in the limit of low coverage, but not when the pores cover a relatively high fraction of the liposome surface area. On the other hand, for a given pore size and surface coverage, the distribution of pores significantly affects the release in the limit of high surface coverage: The rate of release from a liposome covered with a regularly spaced array of pores is, in this limit, higher than the release rate from (most) systems where the pores are distributed randomly on the liposome surface. In contrast, there is little effect of the pore distribution on release when the pore surface coverage is low. The simulation results are in good agreement with the predictions of detailed diffusion models. Copyright © 2014 Elsevier B.V. All rights reserved.

Truncation of the secondary concentrator (CPC) between maximum performances and economical requirements

NASA Astrophysics Data System (ADS)

Segal, A.; Epstein, M.

2009-08-01

A central solar plant, based on beam-down optics, is composed of a field of heliostats, a tower reflector and a ground receiver. The tower reflector is an optical system comprises of a quadric surface mirror (hyperboloid), where its upper focal point coincides with the aim point of a heliostat field and its lower focal point is located at a specified height, coinciding with the entrance plane of the ground receiver. The optics of a tower reflector requires the use of ground secondary concentrator, composed of a cluster of CPCs, because the quadric surface mirror always magnifies the sun image. There is an intrinsic correlation between the tower reflector position and its size on one hand, and the geometry, dimensions and reflective area of the secondary concentrator on the other hand; both are related to the heliostat field reflective area. Obviously, when one wishes to have a smaller tower reflector by placing it closer to the upper focal point, the image created at the lower focus will be larger, resulting in a larger secondary ground concentrator. The present work analyses the ways for a substantial decrease of the size of the ground concentrator cluster (and, implicit, the concentrators area) via truncation, without significant sacrifice of the performance, although some increase of the optical losses is inevitable. This offers a method for cost effective design of future central solar plants utilizing the beam down optics.

Vitamin D production after UVB exposure - a comparison of exposed skin regions.

PubMed

Osmancevic, Amra; Sandström, Katarina; Gillstedt, Martin; Landin-Wilhelmsen, Kerstin; Larkö, Olle; Wennberg Larkö, Ann-Marie; F Holick, Michael; Krogstad, Anne-Lene

2015-02-01

Cholecalciferol is an essential steroid produced in the skin by solar ultraviolet B radiation (UVB 290-315nm). Skin production of cholecalciferol depends on factors affecting UVB flux, age and exposed skin area. Serum cholecalciferol and 25-hydroxyvitamin D3 [25(OH)D3] concentrations were measured after UVB irradiation of 3 different skin areas to compare the skin capacity to produce vitamin D in different anatomic sites in the same individuals. Ten voluntary Caucasians (skin photo type II & III, aged 48±12years (±SD)) were exposed to broadband UVB (280-320nm) between February and April. Hands and face, upper body and whole body were exposed to a suberythemic dose of UVB (median 101mJ/cm(2) (min 66, max 143)) (for 3 subsequent days 24h apart with a wash out period of about 3weeks (median 18days (min 11, max 25)) between the exposures of respective area. Serum concentrations of cholecalciferol and 25(OH)D3, were measured immediately before the first and 24h after the last dose of radiation. There was a significantly higher increase in serum cholecalciferol after UVB exposure of the two larger skin areas compared to face and hands, but no difference in increase was found between upper body and whole body exposures. Exposure of a larger skin area was superior to small areas and gave greater increase in both serum cholecalciferol and serum 25(OH)D3 concentrations. However, exposure of face and hands, i.e. only 5% of the body surface area, was capable of increasing serum concentrations of 25(OH)D3. Copyright © 2015 Elsevier B.V. All rights reserved.

Adhesive behavior of micro/nano-textured surfaces

NASA Astrophysics Data System (ADS)

Zhang, Yuyan; Wang, Xiaoli; Li, Hanqing; Wang, Ben

2015-02-01

A numerical model of the adhesive contact between a rigid smooth sphere and an elastic textured surface based on the Lennard-Jones interatomic potential law and the Hamaker summation method is established. Textures are considered by introducing the texture height distribution into the gap equation. Simulation results show that the pull-off force on textured surfaces decreases compared to that on smooth surfaces. Furthermore, effects of sphere-shaped textures on reducing adhesion are more obvious than cylinder-shaped or cube-shaped textures when the coverage area ratio, maximum height and interval of textures are fixed. For surfaces with sphere-shaped textures, variation trends of the mean pull-off force with texture density are not monotonous, and there exists a certain range of texture densities in which the mean pull-off force is small and its variation is insignificant. In addition, the pull-off force depends also on the maximum height and radius of textures. On one hand, if the texture radius is fixed, larger maximum height results in smaller pull-off force, and if the maximum height is fixed, the pull-off force tends to increase almost linearly with increases in texture radius. On the other hand, if the height-diameter ratio of textures is fixed, the pull-off force reaches a minimum at an optimum texture radius or maximum height.

[Cleaning and disinfection of surfaces in hospitals: Data on structure, process and result in the Frankfurt/Main Metropolitan Area].

PubMed

Hausemann, A; Hofmann, H; Otto, U; Heudorf, Ursel

2015-06-01

In addition to hand hygiene and reprocessing of medical products, cleaning and disinfection of surfaces is also an important issue in the prevention of germ transmission and by implication infections. Therefore, in 2014, the quality of the structure, process and result of surface preparation of all hospitals in Frankfurt am Main, Germany, was monitored. All 17 hospitals transferred information on the quality of structure. Process quality was obtained through direct observation during cleaning and disinfection of rooms and their plumbing units. Result quality was gained using the fluorescent method, i.e. marking surfaces with a fluorescent liquid and testing if this mark has been sufficiently removed by cleaning. Structure quality: in all hospitals the employees were trained regularly. In 12 of them, the foremen had the required qualifications, in 6 hospitals unclarity as to the intersection of the cleaning and care services remained. In 14 hospitals only visible contamination was cleaned on the weekends, whereas complete cleaning was reported to take place in 12 hospitals on Saturdays and in 2 hospitals on Sundays. The contractually stipulated cleaning (observations specified in brackets) averaged 178 m(2)/h (148 m(2)/h) per patient room and 69 m(2)/h (33 m(2)/h) for bathrooms. Process quality: during process monitoring, various hand contact surfaces were prepared insufficiently. Result quality: 63 % of fluorescent markings were appropriately removed. The need for improvement is given especially in the area of the qualification of the foremen and a in a clear definition of the intersection between cleaning and care services, as well as in the regulations for weekends and public holidays.

Field trip guidebook on environmental impact of clays along the upper Texas coast

NASA Technical Reports Server (NTRS)

Garcia, Theron D.; Ming, Douglas W.; Tuck, Lisa Kay

1991-01-01

The field trip was prepared to provide an opportunity to see first hand some the environmental hazards associated with clays in the Houston, Texas area. Because of the very high clay content in area soils and underlying Beaumont Formation clay, Houston is a fitting location to host the Clay Mineral Society. Examinations were made of (1) expansive soils, (2) subsidence and surface faulting, and (3) a landfill located southeast of Houston at the Gulf Coast Waste Disposal Authority where clay is part of the liner material.

Minor burn management: potions and lotions

PubMed Central

Hyland, Ela J; Connolly, Siobhan M; Fox, Jade A; Harvey, John G

2015-01-01

Summary The first aid for burns is to run cold water over the burn for 20 minutes. This is effective for up to three hours after the injury. Assess the affected body surface area using the rule of nines. Consult a burn unit if more than 5% of the total body surface area is burnt in a child or if more than 10% in an adult. Extensive or deep burns and burns to special areas, such as the hands, should be referred. Chemical or electrical burns should also be assessed by a burn unit. For minor burns, antimicrobial dressings are recommended, but oral antibiotics should be avoided unless there are signs of infection. As burns are tetanus prone, check the patient’s immunisation status. Burns that become infected or are slow to heal should be discussed with a burn unit. The burn unit can also provide advice if there are uncertainties about how to manage a patient. PMID:26648640

Study of lysozyme mobility and binding free energy during adsorption on a graphene surface

NASA Astrophysics Data System (ADS)

Nakano, C. Masato; Ma, Heng; Wei, Tao

2015-04-01

Understanding protein adsorption is a key to the development of biosensors and anti-biofouling materials. Hydration essentially controls the adsorption process on hydrophobic surfaces, but its effect is complicated by various factors. Here, we present an ideal model system to isolate hydration effects—lysozyme adsorption on a flat hydrophobic graphene surface. Our all-atom molecular dynamics and molecular-mechanics/Poisson-Boltzmann surface area computation study reveal that lysozyme on graphene displays much larger diffusivity than in bulk water. Protein's hydration free energy within the first hydration shell is dominated by the protein-water electrostatic interactions and acts as an energy barrier for protein adsorption. On the other hand, the surface tension, especially that from the hydrophobic graphene, can effectively weaken the barrier to promote adsorption.

Management of the Acute Partial-thickness Burned Hand; Moist Exposed Burn Ointment or Silver Sulphadiazine Cream both Combined with a Polyethylene Bag.

PubMed

Allam, A M; Mostafa, W; Zayed, E; El-Gamaly, J

2007-09-30

Hand burns predominantly affect young adults, and therefore have serious social and financial implications. In the present work, 106 patients with less than 25% body surface area burns and acute partial-thickness burned hands were managed using polyethylene bags and 1% local silver sulphadiazine (SSD) cream or moist exposed burn ointment (MEBO). Females made up 61.3% of the cases and flame burn was the majority cause (54.7%). There were no significant differences between the two groups regarding either the analgesic effect after local ointment application or hand movement inside the polyethylene bag. Local agent crustation over the wound was very evident in the hands managed by local 1% SSD cream (69.81%). On follow-up, the burned hands healed faster using local MEBO (10.48 versus 14.53 days), with fewer post-burn hand deformities and better active hand movements; however, the total cost until complete hand burn wound healing was higher with MEBO than with 1% SSD, although the final results were superior, with early return to work, when MEBO was used. We concluded that the use of MEBO as a topical agent and of polyethylene bags for the dressing of the acute partial-thickness burned hand accelerated healing; daily wound evaluation was easy as there was no crustation over it of the agent. It was more expensive than 1% SSD cream but presented fewer post-burn complications and more rapid healing, with shorter hospital stay.

Surface Heat Balance Analysis of Tainan City on March 6, 2001 Using ASTER and Formosat-2 Data

PubMed Central

Kato, Soushi; Yamaguchi, Yasushi; Liu, Cheng-Chien; Sun, Chen-Yi

2008-01-01

The urban heat island phenomenon occurs as a mixed result of anthropogenic heat discharge, decreased vegetation, and increased artificial impervious surfaces. To clarify the contribution of each factor to the urban heat island, it is necessary to evaluate the surface heat balance. Satellite remote sensing data of Tainan City, Taiwan, obtained from Terra ASTER and Formosat-2 were used to estimate surface heat balance in this study. ASTER data is suitable for analyzing heat balance because of the wide spectral range. We used Formosat-2 multispectral data to classify the land surface, which was used to interpolate some surface parameters for estimating heat fluxes. Because of the high spatial resolution of the Formosat-2 image, more roads, open spaces and small vegetation areas could be distinguished from buildings in urban areas; however, misclassifications of land cover in such areas using ASTER data would overestimate the sensible heat flux. On the other hand, the small vegetated areas detected from the Formosat-2 image slightly increased the estimation of latent heat flux. As a result, the storage heat flux derived from Formosat-2 is higher than that derived from ASTER data in most areas. From these results, we can conclude that the higher resolution land coverage map increases accuracy of the heat balance analysis. Storage heat flux occupies about 60 to 80% of the net radiation in most of the artificial surface areas in spite of their usages. Because of the homogeneity of the building roof materials, there is no contrast between the storage heat flux in business and residential areas. In sparsely vegetated urban areas, more heat is stored and latent heat is smaller than that in the forested suburbs. This result implies that density of vegetation has a significant influence in decreasing temperatures. PMID:27873856

Spectral and spatial variability of undisturbed and disturbed grass under different view and illumination directions

NASA Astrophysics Data System (ADS)

Borel-Donohue, Christoph C.; Shivers, Sarah Wells; Conover, Damon

2017-05-01

It is well known that disturbed grass covered surfaces show variability with view and illumination conditions. A good example is a grass field in a soccer stadium that shows stripes indicating in which direction the grass was mowed. These spatial variations are due to a complex interplay of spectral characteristics of grass blades, density, their length and orientations. Viewing a grass surface from nadir or near horizontal directions results in observing different components. Views from a vertical direction show more variations due to reflections from the randomly oriented grass blades and their shadows. Views from near horizontal show a mixture of reflected and transmitted light from grass blades. An experiment was performed on a mowed grass surface which had paths of simulated heavy foot traffic laid down in different directions. High spatial resolution hyperspectral data cubes were taken by an imaging spectrometer covering the visible through near infrared over a period of time covering several hours. Ground truth grass reflectance spectra with a hand held spectrometer were obtained of undisturbed and disturbed areas. Close range images were taken of selected areas with a hand held camera which were then used to reconstruct the 3D geometry of the grass using structure-from-motion algorithms. Computer graphics rendering using raytracing of reconstructed and procedurally created grass surfaces were used to compute BRDF models. In this paper, we discuss differences between observed and simulated spectral and spatial variability. Based on the measurements and/or simulations, we derive simple spectral index methods to detect spatial disturbances and apply scattering models.

Comparison of surface roughness and bacterial adhesion between cosmetic contact lenses and conventional contact lenses.

PubMed

Ji, Yong Woo; Cho, Young Joo; Lee, Chul Hee; Hong, Soon Ho; Chung, Dong Yong; Kim, Eung Kweon; Lee, Hyung Keun

2015-01-01

To compare physical characteristics of cosmetic contact lenses (Cos-CLs) and conventional contact lenses (Con-CLs) that might affect susceptibility to bacterial adhesion on the contact lens (CL) surface. Surface characteristics of Cos-CLs and Con-CLs made from the same material by the same manufacturer were measured by atomic force microscopy (AFM) and scanning electron microscopy. To determine the extent and rate of bacterial adhesion, Cos-CL and Con-CL were immersed in serum-free Roswell Park Memorial Institute media containing Staphylococcus aureus or Pseudomonas aeruginosa. Additionally, the rate of removal of adherent bacteria was evaluated using hand rubbing or immersion in multipurpose disinfecting solutions (MPDS). The mean surface roughness (root mean square and peak-to-valley value) measured by AFM was significantly higher for Cos-CL than for Con-CL. At each time point, significantly more S. aureus and P. aeruginosa adhered to Cos-CL than to Con-CL, which correlated with the surface roughness of CL. In Cos-CL, bacteria were mainly found on the tinted surface rather than on the noncolored or convex areas. Pseudomonas aeruginosa attached earlier than S. aureus to all types of CL. However, P. aeruginosa was more easily removed from the surface of CL than S. aureus by hand rubbing or MPDS soaking. Increased surface roughness is an important physical factor for bacterial adhesion in Cos-CL, which may explain why rates of bacterial keratitis rates are higher in Cos-CL users in CL physical characteristics.

Floodplain Assessment for the Middle Los Alamos Canyon Aggregate Area Investigations in Technical Area 02 at Los Alamos National Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hathcock, Charles Dean

The proposed action being assessed in this document occurs in TA-02 in the bottom of Los Alamos Canyon. The DOE proposes to conduct soil sampling at AOC 02-011 (d), AOC 02- 011(a)(ii), and SWMU 02-005, and excavate soils in AOC 02-011(a)(ii) as part of a corrective actions effort. Additional shallow surface soil samples (soil grab samples) will be collected throughout the TA-02 area, including within the floodplain, to perform ecotoxicology studies (Figures 1 and 2). The excavation boundaries in AOC 02-011(a)(ii) are slightly within the delineated 100-year floodplain. The project will use a variety of techniques for soil sampling andmore » remediation efforts to include hand/digging, standard hand auger/sampling, excavation using machinery such as backhoe and front end loader and small drill rig. Heavy equipment will traverse the floodplain and spoils piles will be staged in the floodplain within developed or previously disturbed areas (e.g., existing paved roads and parking areas). The project will utilize and maintain appropriate best management practices (BMPs) to contain excavated materials, and all pollutants, including oil from machinery/vehicles. The project will stabilize disturbed areas as appropriate at the end of the project.« less

Apollo 12 crewmembers during geological field trip

NASA Image and Video Library

1969-10-24

S69-55662 (10 Oct. 1969) --- Astronauts Alan L. Bean (left) and Charles Conrad Jr., the two crewmen of the Apollo 12 lunar landing mission who are scheduled to participate in two lengthy periods of extravehicular activity (EVA) on the lunar surface, are pictured during a geological field trip and training at a simulated lunar surface area near Flagstaff, Arizona. Here Conrad, the Apollo 12 commander, gets a close look through hand lens at the stratigraphy (study of strata or layers beneath the surface) of a man-dug hole, while Bean, the Apollo 12 mission's lunar module pilot, looks on. The topography in this area, with several man-made modifications, resembles very closely much of the topography found on the lunar surface. While Conrad and Bean explore the lunar surface (plans call for Apollo 12 spacecraft to land in the Sea of Storms), astronaut Richard F. Gordon Jr., command module pilot for the Apollo 12 mission, will remain with the Command and Service Modules (CSM) in lunar orbit. The Apollo 12 mission is scheduled to lift off from Cape Kennedy on Nov. 14, 1969.

Epidemiology and outcome analysis of hand burns: A 5-year retrospective review of 378 cases in a burn center in Eastern China.

PubMed

Wang, Kang-an; Sun, Yu; Wu, Guo-sheng; Wang, Yi-ru; Xia, Zhao-fan

2015-11-01

Hands are frequent sites of burn but few related studies were reported in China. The aim of this study was to examine the impacts of gender, age, seasons, place, etiology, total body surface area (TBSA), depth, infection and comorbidities on prognosis following injury in a cohort of hand burn inpatients. This is a retrospective study of total 378 inpatients admitted to the burn center of Changhai hospital from January 2009 to December 2013. The present research showed the male inpatients were predominant and most of the inpatients aged from 20 to 49. Flame (37.04%) and electricity (25.40%) were the major causes of hand burns. Hand burns happened more commonly in work place (60.85%). The study preliminarily pointed out that male, flame and depth were the most significant factors impacting surgery. The main factors relevant to amputation were identified including the electrical burns and other etiology of burns. In addition, depth of hand burns was proved to have a higher impact on length of hospital stay (LOS) than other factors. The results of this study not only provide the necessary information of hand burns in Eastern China but also give the suggestions for the prevention of hand burns. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Numerosity processing is context driven even in the subitizing range: An fMRI study

PubMed Central

Leibovich, Tali; Henik, Avishai; Salti, Moti

2015-01-01

Numerical judgments are involved in almost every aspect of our daily life. They are carried out so efficiently that they are often considered to be automatic and innate. However, numerosity of non-symbolic stimuli is highly correlated with its continuous properties (e.g., density, area), and so it is hard to determine whether numerosity and continuous properties rely on the same mechanism. Here we examined the behavioral and neuronal mechanisms underlying such judgments. We scanned subjects' hemodynamic responses to a numerosity comparison task and to a surface area comparison task. In these tasks, numerical and continuous magnitudes could be either congruent or incongruent. Behaviorally, an interaction between the order of the tasks and the relevant dimension modulated the congruency effects. Continuous magnitudes always interfered with numerosity comparison. Numerosity, on the other hand, interfered with the surface area comparison only when participants began with the numerosity task. Hemodynamic activity showed that context (induced by task order) determined the neuronal pathways in which the dimensions were processed. Starting with the numerosity task led to enhanced activity in the right hemisphere, while starting with the continuous task led to enhanced left hemisphere activity. Continuous magnitudes processing relied on activation of the frontal eye field and the post-central gyrus. Processing of numerosities, on the other hand, relied on deactivation of these areas, suggesting active suppression of the continuous dimension. Accordingly, we suggest that numerosities, even in the subitizing range, are not always processed automatically; their processing depends on context and task demands. PMID:26297625

A Soft Casting Technique for Managing Pediatric Hand and Foot Burns.

PubMed

Choi, Young Mee; Nederveld, Cindy; Campbell, Kristen; Moulton, Steven

2018-04-04

Hand and foot burns in children are difficult to dress. The authors have developed a soft casting technique to manage burns to these areas. The aim of this study is to report the outcomes using weekly dressing changes with a soft casting technique to manage pediatric hand and foot burns in the outpatient setting. A retrospective chart review was performed on children with burns to the hands or feet, who underwent dressing changes with a soft casting technique at the Children's Hospital Colorado Burn Center. Soft casting was performed by placing antibiotic ointment-impregnated nonadherent gauze over the burn wound(s), wrapping the extremity using rolled gauze, applying soft cast pad, plaster, soft cast tape, and an elastic bandage. This was changed weekly. Two hundred ninety-eight children with hand burns had a mean age of 16.8 ± 2 months. Two hundred forty-eight children had partial thickness burn injuries (83%), 50 had full thickness burn injuries (17%), and the mean total body surface area (TBSA) was 1 ± 2.4%. The mean time to heal was 10.1 ± 1.7 days for all subjects. Sixty-six children with foot burns were identified with a mean age of 24 ± 2.6 months. Forty-six children had partial thickness injuries (70%), 20 had full thickness burn injuries (30%), and the mean TBSA was 2.3 ± 2.9%. The mean time to heal was 14.1 ± 2.2 days for all subjects. Weekly dressing changes using a soft casting technique are effective for the outpatient management of pediatric hand and foot burns. This method avoids costly inpatient hospital care, reduces the number of painful dressing changes, and allows children to heal in their own environment.

Posterior parietal cortex contains a command apparatus for hand movements.

PubMed

Rathelot, Jean-Alban; Dum, Richard P; Strick, Peter L

2017-04-18

Mountcastle and colleagues proposed that the posterior parietal cortex contains a "command apparatus" for the operation of the hand in immediate extrapersonal space [Mountcastle et al. (1975) J Neurophysiol 38(4):871-908]. Here we provide three lines of converging evidence that a lateral region within area 5 has corticospinal neurons that are directly linked to the control of hand movements. First, electrical stimulation in a lateral region of area 5 evokes finger and wrist movements. Second, corticospinal neurons in the same region of area 5 terminate at spinal locations that contain last-order interneurons that innervate hand motoneurons. Third, this lateral region of area 5 contains many neurons that make disynaptic connections with hand motoneurons. The disynaptic input to motoneurons from this portion of area 5 is as direct and prominent as that from any of the premotor areas in the frontal lobe. Thus, our results establish that a region within area 5 contains a motor area with corticospinal neurons that could function as a command apparatus for operation of the hand.

Young children's hand contact activities: an observational study via videotaping in primarily outdoor residential settings.

PubMed

Auyeung, Willa; Canales, Robert A; Beamer, Paloma; Ferguson, Alesia C; Leckie, James O

2006-09-01

Microlevel activity time series (MLATS) data were gathered on hand contact activities of 38 children (1-6 years old) by videotaping in primarily outdoor residential environments. The videotape recordings were then translated into text files using a specialized software called VirtualTimingDevicetrade mark. Contact frequency (contacts/h), duration per contact (s/contact), and hourly contact duration (min/h) were summarized for outdoor hand contacts with 15 distinct object/surface categories ("Animal", "Body", "Clothes/Towels", "Fabric", "Floor", "Food", "Footwear", "Metal", "Non-dietary Water", "Paper/Wrapper", "Plastic", "Rock/Brick", "Toys", "Vegetation/Grass", and "Wood") and two aggregate object/surface categories ("Non-dietary objects/surfaces" and "Total objects/surfaces"). For outdoor both hand contacts with "Total objects/surfaces", contact frequencies ranged from 229.9 to 1517.7 contacts/h, median durations/contact ranged from < 1 to 5 s, and hourly contact durations ranged from 42.6 to 102.2 m/h. The data were analyzed for significant differences in hand contact activities as a function of (1) age, (2) location, (3) gender, and (4) hand. Significant differences (P < or = 0.05) were found for all four factors analyzed. Hourly contact durations with "Non-dietary objects/surfaces" and "Total objects/surfaces" increased with age (P = 0.01, rs = 0.42 and P = 0.005, rs = 0.46, respectively), while contact frequencies and hourly contact durations with "Wood" decreased with age (P = 0.02, rs = -0.38 and P = 0.05, rs = -0.32, respectively). Location was found to affect contact frequencies and hourly contact durations with certain objects/surfaces. For example, contact frequencies and hourly contact durations with "Fabric" were higher indoors (P = 0.02 for both), while contact frequencies and hourly contact durations with "Vegetation/Grass" were higher outdoors (P = 0.02 and P = 0.04, respectively). Girls had longer hourly contact durations with "Footwear" (P = 0.02), "Non-dietary objects/surfaces" (P = 0.03), and "Total objects/surfaces" (P = 0.01) than boys. The right hand had longer hourly contact durations with objects that are often manipulated with the hand (e.g., "Toys" (P = 0.0002)), while the left hand had longer hourly contact durations with passively touched objects/surfaces (e.g., "Clothes/Towels" (P = 0.003) and "Floor" (P = 0.04)).

Touch activates human auditory cortex.

PubMed

Schürmann, Martin; Caetano, Gina; Hlushchuk, Yevhen; Jousmäki, Veikko; Hari, Riitta

2006-05-01

Vibrotactile stimuli can facilitate hearing, both in hearing-impaired and in normally hearing people. Accordingly, the sounds of hands exploring a surface contribute to the explorer's haptic percepts. As a possible brain basis of such phenomena, functional brain imaging has identified activations specific to audiotactile interaction in secondary somatosensory cortex, auditory belt area, and posterior parietal cortex, depending on the quality and relative salience of the stimuli. We studied 13 subjects with non-invasive functional magnetic resonance imaging (fMRI) to search for auditory brain areas that would be activated by touch. Vibration bursts of 200 Hz were delivered to the subjects' fingers and palm and tactile pressure pulses to their fingertips. Noise bursts served to identify auditory cortex. Vibrotactile-auditory co-activation, addressed with minimal smoothing to obtain a conservative estimate, was found in an 85-mm3 region in the posterior auditory belt area. This co-activation could be related to facilitated hearing at the behavioral level, reflecting the analysis of sound-like temporal patterns in vibration. However, even tactile pulses (without any vibration) activated parts of the posterior auditory belt area, which therefore might subserve processing of audiotactile events that arise during dynamic contact between hands and environment.

Comparison of glacier loss on Qori Kalis, Peru and Mt. Kilimanjaro, Tanzania over the last decade using digital photogrammetry and stereo analysis

NASA Astrophysics Data System (ADS)

Lamantia, K.

2017-12-01

Rising global temperatures have created cause for concern, particularly among those who study the world's glaciers. Given their high sensitivity to climate change tropical glaciers can be used not only as indicators of change but can provide information necessary for more accurate interpretations of the mechanisms driving climate change. In the past, measurements of glacier extent changes such as for the Qori Kalis Glacier in Peru have been based on terrestrial photography and hand-plotted photogrammetry. Recent technological advances now provide an opportunity to modify the way these glaciers are observed and measured. New developments have opened doors for digital photogrammetry software such as the Leica Photogrammetry Suite and stereo analyst from ERDAS, which offers stereoscopic tools with the ability to plot the ice extent in a three dimensional image. At least two images from different perspectives are required to create the file for stereo analysis. The resulting three-dimensional digital content will offer more flexibility in analysis, quantification, and visualization for better documentation of retreating glaciers. It is possible to produce both two-and three-dimensional surface area estimations for glaciers such as Qori Kalis and the Kilimanjaro ice fields. Beyond a surface area measurement, the software also possesses the capability to create contours for the surface of the glacier as well as view and analyze properties such as slope and aspect. The surface area measurements taken with the digital method are compared with the hand-plotted measurements made in the past and are found to be comparable. A comparison of glacier loss over time as well as a comparison between both tropical locations, will be presented and should provide better insight to the drivers that are influencing current glacier loss. Making the transition from terrestrial, to aerial, and now to satellite imagery provides a simpler method for accessing and assessing changes in glaciated regions of the world.

Lake surface area variation and its responses to climatic change in Yamzhog Yumco Basin, South Tibet during 1970-2010

NASA Astrophysics Data System (ADS)

Zhang, X.; Tian, Y.; Sun, R.

2015-12-01

The research on lake extraction from multi-source and multi-temporal satellite images and the lake size variation can provide reliable method and indispensable information to deepen the understanding about alpine lake changes with the accelerating warming. With field survey experience in the Yamzhog Yumco Basin, South Tibet, the outlines of five lakes (i.e., Yamzhog Yumco, Chen Co, Kongmu Co, Bajiu Co and Puma Yumco) were delineated by the adoption of 42 scenes of satellite images from Landsat, CBERS and HJ from 1970 to 2010, basing on which the responses of alpine lakes to climate change at different timescales were explored. The results are summarized as follows. (1) The seasonal fluctuation of lake surface area was similar with different trend for the five alpine lakes. As for the last 41 years, the annual variation of lake surface area exhibited two kinds of patterns for the five alpine lakes. And the Yamzhog Yumco declined by 9.41%, while the rest four lakes expanded. (2) The responses of alpine lakes to climate change rely on different timescale and water replenishment types. On the one hand, the precipitation change was the predominant driving forces for the seasonal fluctuation and variation trend of lake size, and the rising temperature accounted for the inter-annual lake surface variation. On the other hand, the two kinds of alpine lakes behaviors were well correspondent with the warming temperature over the Qinghai-Tibetan Plateau. The lakes supplied mainly by precipitation shrunk as a result of increased evaporation, and lakes supplied mainly by glacier and snow meltwater, however, expanded because of the remarkable glacier recession. (3) The quantification of hydrological components would hopefully be improved, according to uncertainties analysis, with the adoption of microwave satellite images and higher resolution ones to disclose the interaction mechanism among climate, glacier, and lake in alpine regions.

Manipulating surface wettability and oil absorbency of diatomite depending on processing and ambient conditions

NASA Astrophysics Data System (ADS)

Özen, İlhan; Şimşek, Süleyman; Okyay, Gamze

2015-03-01

In this study, a diatomite sample, which is a natural inorganic mineral with inherently high water and oil absorption capacity, was subjected to grinding before surface modification. Afterwards, the diatomite surface was modified via facile methods using a fluorocarbon (FC) chemical and stearic acid (SA) in addition to the sol-gel fluorosilanization (FS) process. The water and oil wettability, and oil absorbency properties of the unmodified and modified diatomites were investigated in addition to diatomite characterizations such as chemical content, surface area, particle size distribution, morphology, and modification efficiency. It was revealed that the wettability was changed completely depending on the surface modification agent and the media used, while the oil absorbency property surprisingly did not change. On the other hand, the oil absorbency was worsened by the grinding process, whereas the wettability was not affected.

Study of lysozyme mobility and binding free energy during adsorption on a graphene surface

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nakano, C. Masato; Ma, Heng; Wei, Tao, E-mail: twei@lamar.edu

Understanding protein adsorption is a key to the development of biosensors and anti-biofouling materials. Hydration essentially controls the adsorption process on hydrophobic surfaces, but its effect is complicated by various factors. Here, we present an ideal model system to isolate hydration effects—lysozyme adsorption on a flat hydrophobic graphene surface. Our all-atom molecular dynamics and molecular-mechanics/Poisson-Boltzmann surface area computation study reveal that lysozyme on graphene displays much larger diffusivity than in bulk water. Protein's hydration free energy within the first hydration shell is dominated by the protein-water electrostatic interactions and acts as an energy barrier for protein adsorption. On the othermore » hand, the surface tension, especially that from the hydrophobic graphene, can effectively weaken the barrier to promote adsorption.« less

Computer Controlled Optical Surfacing With Orbital Tool Motion

NASA Astrophysics Data System (ADS)

Jones, Robert A.

1985-10-01

Asymmetric aspheric optical surfaces are very difficult to fabricate using classical techniques and laps the same size as the workpiece. Opticians can produce such surfaces by grinding and polishing, using small laps with orbital tool motion. However, hand correction is a time consuming process unsuitable for large optical elements. Itek has developed Computer Controlled Optical Surfacing (CCOS) for fabricating such aspheric optics. Automated equipment moves a nonrotating orbiting tool slowly over the workpiece surface. The process corrects low frequency surface errors by figuring. The velocity of the tool assembly over the workpiece surface is purposely varied. Since the amount of material removal is proportional to the polishing or grinding time, accurate control over material removal is achieved. The removal of middle and high frequency surface errors is accomplished by pad smoothing. For a soft pad material, the pad will compress to fit the workpiece surface producing greater pressure and more removal at the surface high areas. A harder pad will ride on only the high regions resulting in removal only for those locations.

Estimation of Areal Distribution of Evapotranspiration Using Remotely Sensed Data During Vegetation Period in Hungary

NASA Astrophysics Data System (ADS)

Dunkel, Z.; Szenyán, I. G.

The surface temperature measured by satellite can be the basis of evapotranspiration (ET) computation. The possibility of calculation of daily sum of the regional ET using surface temperature was examined under Hungarian weather conditions. A simplified relationship, namely ETd-Rnd = a + b (Tc-Ta), which relates the daily ET to daily net radiation with one measurements of surface and air temperature was used for the calculation. Using NOAA/AVHRR satellite data, no information about the surface inhomogeneity was obtained. The distribution of surface temperature was investigated by infrared thermometer scanning the surface from a board a hang-glider, ultra-light-aeroplane, and light aeroplane. Field observation trials were made during the vegetation period of 1992, 1993, 1994 and 1995. In eastern part of the country a homogeneous field (1 km × 1 km) was scanned before noon and afternoon. In the western part of the country, a much larger area (45 km × 45 km) was investigated. Cultivated area, forest and a large water surface were included in the investigated surface. The problems of calibration of hand-held infrared thermometer and the time shifting are discussed too. Comparison of model output with data from field experiment has played a crucial role in model development and suggested evaluation method

Surveillance of Site A and Plot M, Report for 2009.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golchert, N. W.

2010-04-21

The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2009 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are usedmore » to monitor the migration pathway of hydrogen-3 contaminated water from the burial ground (Plot M) to the hand-pumped picnic wells and monitor for the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.« less

Surveillance of Site A and Plot M report for 2010.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Golchert, N. W.

2011-05-31

The results of the environmental surveillance program conducted at Site A/Plot M in the Palos Forest Preserve area for Calendar Year 2010 are presented. Based on the results of the 1976-1978 radiological characterization of the site, a determination was made that a surveillance program be established. The characterization study determined that very low levels of hydrogen-3 (as tritiated water) had migrated from the burial ground and were present in two nearby hand-pumped picnic wells. The current surveillance program began in 1980 and consists of sample collection and analysis of surface and subsurface water. The results of the analyses are usedmore » to monitor the migration pathway of hydrogen-3 contaminated water from the burial ground (Plot M) to the hand-pumped picnic wells and monitor for the presence of radioactive materials in the environment of the area. Hydrogen-3 in the Red Gate Woods picnic wells was still detected this year, but the average and maximum concentrations were significantly less than found earlier. Hydrogen-3 continues to be detected in a number of wells, boreholes, dolomite holes, and a surface stream. Analyses since 1984 have indicated the presence of low levels of strontium-90 in water from a number of boreholes next to Plot M. The results of the surveillance program continue to indicate that the radioactivity remaining at Site A/Plot M does not endanger the health or safety of the public visiting the site, using the picnic area, or living in the vicinity.« less

Management of the Acute Partial-thickness Burned Hand; Moist Exposed Burn Ointment or Silver Sulphadiazine Cream both Combined with a Polyethylene Bag

PubMed Central

Allam, A.M.; Mostafa, W.; Zayed, E.; El-Gamaly, J.

2007-01-01

Summary Hand burns predominantly affect young adults, and therefore have serious social and financial implications. In the present work, 106 patients with less than 25% body surface area burns and acute partial-thickness burned hands were managed using polyethylene bags and 1% local silver sulphadiazine (SSD) cream or moist exposed burn ointment (MEBO). Females made up 61.3% of the cases and flame burn was the majority cause (54.7%). There were no significant differences between the two groups regarding either the analgesic effect after local ointment application or hand movement inside the polyethylene bag. Local agent crustation over the wound was very evident in the hands managed by local 1% SSD cream (69.81%). On follow-up, the burned hands healed faster using local MEBO (10.48 versus 14.53 days), with fewer post-burn hand deformities and better active hand movements; however, the total cost until complete hand burn wound healing was higher with MEBO than with 1% SSD, although the final results were superior, with early return to work, when MEBO was used. We concluded that the use of MEBO as a topical agent and of polyethylene bags for the dressing of the acute partial-thickness burned hand accelerated healing; daily wound evaluation was easy as there was no crustation over it of the agent. It was more expensive than 1% SSD cream but presented fewer post-burn complications and more rapid healing, with shorter hospital stay. PMID:21991086

Area- and band-specific representations of hand movements by local field potentials in caudal cingulate motor area and supplementary motor area of monkeys

PubMed Central

Yokoyama, Osamu; Nakayama, Yoshihisa

2016-01-01

The caudal cingulate motor area (CMAc) and the supplementary motor area (SMA) play important roles in movement execution. The present study examined the neural mechanisms underlying these roles by investigating local field potentials (LFPs) from these areas while monkeys pressed buttons with either their left or right hand. During hand movement, power increases in the high-gamma (80–120 Hz) and theta (3–8 Hz) bands and a power decrease in the beta (12–30 Hz) band were observed in both the CMAc and SMA. High-gamma and beta activity in the SMA predominantly represented contralateral hand movements, whereas activity in the CMAc preferentially represented movement of either hand. Theta activity in both brain regions most frequently reflected movement of either hand, but a contralateral hand bias was more evident in the SMA than in the CMAc. An analysis of the relationships of the laterality representations between the high-gamma and theta bands at each recording site revealed that, irrespective of the hand preference for the theta band, the high-gamma band in the SMA preferentially represented contralateral hand movement, whereas the high-gamma band in the CMAc represented movement of either hand. These findings suggest that the input-output relationships for ipsilateral and contralateral hand movements in the CMAc and SMA differ in terms of their functionality. The CMAc may transform the input signals representing general aspects of movement into commands to perform movements with either hand, whereas the SMA may transform the input signals into commands to perform movement with the contralateral hand. PMID:26792884

Relationship between healthcare worker surface contacts, care type and hand hygiene: an observational study in a single-bed hospital ward.

PubMed

King, M-F; Noakes, C J; Sleigh, P A; Bale, S; Waters, L

2016-09-01

This study quantifies the relationship between hand hygiene and the frequency with which healthcare workers (HCWs) touch surfaces in patient rooms. Surface contacts and hand hygiene were recorded in a single-bed UK hospital ward for six care types. Surface contacts often formed non-random patterns, but hygiene before or after patient contact depends significantly on care type (P=0.001). The likelihood of hygiene correlated with the number of surface contacts (95% confidence interval 1.1-5.8, P=0.002), but not with time spent in the room. This highlights that a potential subconscious need for hand hygiene may have developed in HCWs, which may support and help focus future hygiene education programmes. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

Effect of surface texturing on superoleophobicity, contact angle hysteresis, and "robustness".

PubMed

Zhao, Hong; Park, Kyoo-Chul; Law, Kock-Yee

2012-10-23

Previously, we reported the creation of a fluorosilane (FOTS) modified pillar array silicon surface comprising ~3-μm-diameter pillars (6 μm pitch with ~7 μm height) that is both superhydrophobic and superoleophobic, with water and hexadecane contact angles exceeding 150° and sliding angles at ~10° owing to the surface fluorination and the re-entrant structure in the side wall of the pillar. In this work, the effects of surface texturing (pillar size, spacing, and height) on wettability, contact angle hysteresis, and "robustness" are investigated. We study the static, advancing, and receding contact angles, as well as the sliding angles as a function of the solid area fraction. The results reveal that pillar size and pillar spacing have very little effect on the static and advancing contact angles, as they are found to be insensitive to the solid area fraction from 0.04 to ~0.4 as the pillar diameter varies from 1 to 5 μm and the center-to-center spacing varies from 4.5 to 12 μm. On the other hand, sliding angle, receding contact angle, and contact angle hysteresis are found to be dependent on the solid area fraction. Specifically, receding contact angle decreases and sliding angle and hysteresis increase as the solid area fraction increases. This effect can be attributable to the increase in pinning as the solid area fraction increases. Surface Evolver modeling shows that water wets and pins the pillar surface whereas hexadecane wets the pillar surface and then penetrates into the side wall of the pillar with the contact line pinning underneath the re-entrant structure. Due to the penetration of the hexadecane drop into the pillar structure, the effect on the receding contact angle and hysteresis is larger relative to that of water. This interpretation is supported by studying a series of FOTS pillar array surfaces with varying overhang thickness. With the water drop, the contact line is pinned on the pillar surface and very little overhang thickness effect was observed. On the other hand, the hexadecane drop is shown to wet the pillar surface and the side wall of the overhang. It then pins at the lower edge of the overhang structure. A plot of the thickness of the overhang as a function of the static, advancing, and receding contact angles and sliding angle of hexadecane reveals that static, advancing, and receding contact angles decrease and sliding angle increases as the thickness of the overhang increases. A larger overhang effect is observed with octane due to its lower surface tension. The robustness of the pillar array surface against external pressure induced wetting and abrasion was modeled. Surface Evolver simulation (with the hexadecane drop) indicates that wetting breakthrough pressure as high as ~70 kPa is achievable with 0.5-μm-diameter pillar array FOTS surfaces. Mechanical modeling shows that bending of the pillars is the key failure by abrasion, which can be avoided with a short pillar structure. The path to fabricate a superoleophobic surface that can withstand the external force equivalent of a gentle cleaning blade (up to ~30 kPa) without wetting and abrasion failure is discussed.

A mild hand cleanser, alkyl ether sulphate supplemented with alkyl ether carboxylic acid and alkyl glucoside, improves eczema on the hand and prevents the growth of Staphylococcus aureus on the skin surface.

PubMed

Fukui, S; Morikawa, T; Hirahara, M; Terada, Y; Shimizu, M; Takeuchi, K; Takagi, Y

2016-12-01

Washing the hands using cleansers with antiseptic materials is the most popular method for hand hygiene and helps maintain health by preventing food poisoning and bacterial infections. However, repeated hand washing tends to induce eczema of the hand, such as dryness, cracking and erythema. Moreover, eczema on the hand leads to increased levels in Staphylococcus aureus (S. aureus) on the skin surface in contrast to expectations. Thus, mild hand cleansers which induce less eczema even with repeated washings are desired. Here, we evaluated the efficacy of a hand cleanser formulated with alkyl ether sulphate (AES), alkyl ether carboxylic acid (AEC) and alkyl glucoside (AG) that contains isopropyl methylphenol (IPMP) on skin symptoms and S. aureus levels. Eczema of the hand and the presence of S. aureus on the skin surface were analysed prior to and following 4 weeks of usage of the hand cleanser. A soap-based hand cleanser with IPMP was used as a reference cleanser. Eczema and cutaneous conditions were evaluated by visual grading, transepidermal water loss (TEWL), stratum corneum moisture-retention ability (MRA) and skin surface pH. The repeated use of the soap-based hand cleanser significantly worsened the hand dryness, scaling and cracks on the tips of the fingers and significantly increased the TEWL and decreased the MRA. In contrast, usage of the test cleanser only induced a significant increase in skin dryness but did not induce skin scaling or cracking and did not increase TEWL or decrease the MRA. Corresponding to these changes in skin symptoms, the presence of S. aureus increased the following use of the reference cleanser but not the test cleanser. There was no significant difference in skin surface pH between the two cleansers. Moreover, the increase in S. aureus was significantly correlated to the worsening of skin dryness and scaling. These results suggest that not only antimicrobial activity but also the mildness, which minimizes cutaneous effects, are important for hand cleansers to prevent the growth of S. aureus. The cleanser formulated with AES, AEC and AG containing IPMP is mild and is effective to promote hand hygiene. © 2016 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

Contact pin-printing of albumin-fungicide conjugate for silicon nitride-based sensors biofunctionalization: Multi-technique surface analysis for optimum immunoassay performance

NASA Astrophysics Data System (ADS)

Gajos, Katarzyna; Budkowski, Andrzej; Tsialla, Zoi; Petrou, Panagiota; Awsiuk, Kamil; Dąbczyński, Paweł; Bernasik, Andrzej; Rysz, Jakub; Misiakos, Konstantinos; Raptis, Ioannis; Kakabakos, Sotirios

2017-07-01

Mass fabrication of integrated biosensors on silicon chips is facilitated by contact pin-printing, applied for biofunctionalization of individual Si3N4-based transducers at wafer-scale. To optimize the biofunctionalization for immunochemical (competitive) detection of fungicide thiabendazole (TBZ), Si3N4 surfaces are modified with (3-aminopropyl)triethoxysilane and examined after: immobilization of BSA-TBZ conjugate (probe) from solutions with different concentration, blocking with bovine serum albumin (BSA), and immunoreaction with a mouse monoclonal antibody against TBZ. Nanostructure, surface density, probe composition and coverage uniformity of protein layers are evaluated with Atomic Force Microscopy, Spectroscopic Ellipsometry, Time-of-Flight Secondary Ion Mass Spectrometry and X-ray Photoelectron Spectroscopy. Contact pin-printing of overlapping probe spots is compared with hand spotted areas. Contact pin-printing resulted in two-fold increase of immobilized probe surface density as compared to hand spotting. Regarding BSA-TBZ immobilization, an incomplete monolayer develops into a bilayer as the concentration of BSA-TBZ molecules in the printing solution increases from 25 to 100 μg/mL. Upon blocking, however, a complete protein monolayer is formed for all the BSA-TBZ concentrations used. Free surface sites are filled with BSA for low surface coverage with BSA-TBZ, whereas loosely bound BSA-TBZ molecules are removed from the BSA-TBZ bilayer. As a consequence immunoreaction efficiency increases with the printing probe concentration.

Motor cortex hand area and speech: implications for the development of language.

PubMed

Meister, Ingo Gerrit; Boroojerdi, Babak; Foltys, Henrik; Sparing, Roland; Huber, Walter; Töpper, Rudolf

2003-01-01

Recently a growing body of evidence has suggested that a functional link exists between the hand motor area of the language dominant hemisphere and the regions subserving language processing. We examined the excitability of the hand motor area and the leg motor area during reading aloud and during non-verbal oral movements using transcranial magnetic stimulation (TMS). During reading aloud, but not before or afterwards, excitability was increased in the hand motor area of the dominant hemisphere. This reading effect was found to be independent of the duration of speech. No such effect could be found in the contralateral hemisphere. The excitability of the leg area of the motor cortex remained unchanged during reading aloud. The excitability during non-verbal oral movements was slightly increased in both hemispheres. Our results are consistent with previous findings and may indicate a specific functional connection between the hand motor area and the cortical language network.

Dust transportation in bounday layers on complex areas

NASA Astrophysics Data System (ADS)

Karelsky, Kirill; Petrosyan, Arakel

2017-04-01

This presentation is aimed at creating and realization of new physical model of impurity transfer (solid particles and heavy gases) in areas with non-flat and/or nonstationary boundaries. The main idea of suggested method is to use non-viscous equations for solid particles transport modeling in the vicinity of complex boundary. In viscous atmosphere with as small as one likes coefficient of molecular viscosity, the non-slip boundary condition on solid surface must be observed. This postulates the reduction of velocity to zero at a solid surface. It is unconditionally in this case Prandtle hypothesis must be observed: for rather wide range of conditions in the surface neighboring layers energy dissipation of atmosphere flows is comparable by magnitude with manifestation of inertia forces. That is why according to Prandtle hypothesis in atmosphere movement characterizing by a high Reynolds number the boundary layer is forming near a planet surface, within which the required transition from zero velocities at the surface to magnitudes at the external boundary of the layer that are quite close to ones in ideal atmosphere flow. In that layer fast velocity gradients cause viscous effects to be comparable in magnitude with inertia forces influence. For conditions considered essential changes of hydrodynamic fields near solid boundary caused not only by nonslip condition but also by a various relief of surface: mountains, street canyons, individual buildings. Transport of solid particles, their ascent and precipitation also result in dramatic changes of meteorological fields. As dynamic processes of solid particles transfer accompanying the flow past of complex relief surface by wind flows is of our main interest we are to use equations of non-viscous hydrodynamic. We should put up with on the one hand idea of high wind gradients in the boundary layer and on the other hand disregard of molecular viscosity in two-phase atmosphere equations. We deal with describing high field gradients with the aid of scheme viscosity of numerical algorithm used to model near-surface phenomena. This idea is implemented in the model of ideal gas equations with variable equation of state describing particulates transportation within boundary layer with obstacles.

A new preparation of doped photocatalytic TiO2 anatase nanoparticles: a preliminary study for the removal of pollutants in confined museum areas

NASA Astrophysics Data System (ADS)

Greco, Enrico; Ciliberto, Enrico; Cirino, Antonio M. E.; Capitani, Donatella; Di Tullio, Valeria

2016-05-01

The use of nanotechnology in conservation is a relatively new concept. Usually, classical cleanup methods take into account the use of other chemicals: On the one hand they help the environment destroying pollutants, but on the other hand they often become new pollutants. Among the new oxidation methods called advanced oxidation processes, heterogeneous photocatalysis has appeared an emerging technology with several economic and environmental advantages. A new sol-gel method of synthesis of TiO2 anatase is reported in this work using lithium and cobalt (II) salts. The activation energy of the doped photocatalyst was analyzed by solid-state UV-Vis spectrophotometer. The mobility of Li ions on TiO2 NPs surface was studied by 7Li MAS NMR spectroscopy. Use of doped nanotitania is suggested from authors for the removal of pollutants in confined areas containing goods that must be preserved from decomposition and aging phenomena.

Methamphetamine residue dermal transfer efficiencies from household surfaces.

PubMed

Van Dyke, Mike; Martyny, John W; Serrano, Kate A

2014-01-01

Methamphetamine contamination from illegal production operations poses a potential health concern for emergency responders, child protective services, law enforcement, and children living in contaminated structures. The objective of this study was to evaluate dermal transfer efficiencies of methamphetamine from contaminated household surfaces. These transfer efficiencies are lacking for methamphetamine, and would be beneficial for use in exposure models. Surfaces were contaminated using a simulated smoking method in a stainless steel chamber. Household surfaces were carpet, painted drywall, and linoleum. Dermal transfer efficiencies were obtained using cotton gloves for two hand conditions, dry or saliva moistened (wet). In addition, three contact scenarios were evaluated for both hand conditions: one, two, or three contacts with contaminated surfaces. Dermal transfer efficiencies were calculated for both hand conditions and used as inputs in a Stochastic Human Exposure and Dose Simulation model (SHEDS-Multimedia, Office of Research and Development, United States Environmental Protection Agency, Research Triangle Park, N.C.). Results of this study showed that average dermal transfer efficiencies of methamphetamine ranged from 11% for dry hands to 26% for wet hands. There was a significantly higher wet transfer as compared to dry transfer for all surfaces. For wet hands, dermal transfer depended on surface type with higher transfer from carpet and linoleum as compared to drywall. Based on our estimates of dermal transfer efficiency, a surface contamination clearance level of 1.5 μg/100 cm(2) may not ensure absorbed doses remain below the level associated with adverse health effects in all cases. Additional dermal transfer studies should be performed using skin surrogates that may better predict actual skin transfer.

The effect of video-guidance on passive movement in patients with cerebral palsy: fMRI study.

PubMed

Dinomais, Mickael; Chinier, Eva; Lignon, Gregoire; Richard, Isabelle; Ter Minassian, Aram; Tich, Sylvie Nguyen The

2013-10-01

In patients with cerebral palsy (CP), neuroimaging studies have demonstrated that passive movement and action-observation tasks have in common to share neuronal activation in all or part of areas involved in motor system. Action observation with simultaneous congruent passive movements may have additional effects in the recruitment of brain motor areas. The aim of this functional magnetic resonance imaging (fMRI) study was to examine brain activation in patients with unilateral CP during passive movement with and without simultaneous observation of simple hand movement. Eighteen patients with unilateral CP (fourteen male, mean age 14 years and 2 months) participated in the study. Using fMRI block design, brain activation following passive simple opening-closing hand movement of either the paretic or nonparetic hand with and without simultaneous observation of a similar movement performed by either the left or right hand of an actor was compared. Passive movement of the paretic hand performed simultaneously to the observation of congruent movement activated more "higher motor areas" including contralesional pre-supplementary motor area, superior frontal gyrus (extending to premotor cortex), and superior and inferior parietal regions than nonvideo-guided passive movement of the paretic hand. Passive movement of the paretic hand recruited more ipsilesional sensorimotor areas compared to passive movement of the nonparetic hand. Our study showed that the combination of observation of congruent hand movement simultaneously to passive movement of the paretic hand recruits more motor areas, giving neuronal substrate to propose video-guided passive movement of paretic hand in CP rehabilitation. Copyright © 2013 Elsevier Ltd. All rights reserved.

Isolation frequency of Candida present on the surfaces of mobile phones and handsx.

PubMed

Kordecka, Anna; Krajewska-Kułak, Elżbieta; Łukaszuk, Cecylia; Kraszyńska, Bogumiła; Kułak, Wojciech

2016-06-01

It is known that mobile phones may play a role in microorganism transmission. The aim of this study was to analyze the relationship between the number of Candida genera/species isolated from samples collected from the surfaces of mobile phones and the hands of the staff as well as the preferred health-related behavior. The mycological evaluation included 175 mobile telephones and the hands of staff members at the University Hospital in Białystok, Poland. We used the Count-Tact(TM) applicator, with CandiSelect (Bio-Rad). Self-administered questionnaire was used to gather data on mobile phones disinfection practices. Assessment of the preferred health-related behavior was based on The Multidemensional Health Locus of Control Scale (MHLC). Out of 175 mobile phones, 131 (74.9 %) were colonized. Candida glabrata, C. albicans and C.krusei were isolated more frequently from the hand as well as phone surface. The mean number of Candida colonies was higher in samples collected from hand surfaces than mobile phone surfaces. No significant correlation was found between the preferred health-related behavior and the frequency of washing hands, the way of using a mobile phone, the number of colonies or the isolation frequency for the fungi collected from the surface of the phones and hands of their owners. Only 19.4 % of the participants cleaned the surface of their phones. The prevalence of mobile phone contamination by Candida is high in the University Hospital in Białystok, Poland. Candida albicans, C. glabrata, and C. krusei were the dominant species in the samples collected from mobile phones and hands. These results pose the need to develop guidelines for mobile phone disinfection.

Building 3D Layer-by-Layer Graphene-Gold Nanoparticle Hybrid Architecture with Tunable Interlayer Distance

DTIC Science & Technology

2014-06-26

supercapacitors .11 On the other hand, because of the anisotropic graphene structure, it exhibits strong direction- dependent properties, including...GNPs has the advantage of increased surface area for supercapacitor .11 2. EXPERIMENTAL SECTION 2.1. Materials and Instruments. All chemicals and...rectangular, which means that this material has good potential for applications such as supercapacitors .22 In an ideal situation, it can be envisioned that

Heteroatom-doped nanoporous carbon derived from MOF-5 for CO2 capture

NASA Astrophysics Data System (ADS)

Ma, Xiancheng; Li, Liqing; Chen, Ruofei; Wang, Chunhao; Li, Hailong; Wang, Shaobin

2018-03-01

Four nanoporous carbons (MUCT) were prepared from metal-organic framework (MOF-5) template and additional carbon source (i.e. urea) by carbonization at different temperatures (600-900 °C). The results showed that specific surface area of four samples was obtained in the range from 1030 to 2307 m2 g-1. By changing the carbonization temperature it can finely tune the pore volume of the MUCT, which having a uniform pore size of around 4.0 nm. With an increasing carbonization temperature, the micropore surface area of MUCT samples varied slightly, but mesopore surface area increased obviously, which had little influence on carbon dioxide (CO2) adsorption capacity. The as-obtained sample MUC900 exhibited the superior CO2 capture capacity of 3.7 mmol g-1 at 0 °C (1 atm). First principle calculations were conducted on carbon models with various functional groups to distinguish heterogeneity and understand carbon surface chemistry for CO2 adsorption. The interaction between CO2 and N-containing functional groups is mainly weak Lewis acid-base interaction. On the other hand, the pyrrole and amine groups show exceptional hydrogen-bonding interaction. The hydroxyls promote the interaction between carbon dioxide and functional groups through hydrogen-bonding interactions and electrostatic potentials, thereby increasing CO2 capture of MUCT.

Lidar-based fracture characterization: An outcrop-scale study of the Woodford Shale, McAlister Shale Pit, Oklahoma

NASA Astrophysics Data System (ADS)

Hanzel, Jason

The use of lidar (light detection and ranging), a remote sensing tool based on principles of laser optometry, in mapping complex, multi-scale fracture networks had not been rigorously tested prior to this study despite its foreseeable utility in interpreting rock fabric with imprints of complex tectonic evolution. This thesis demonstrates lidar-based characterization of the Woodford Shale where intense fracturing could be due to both tectonism and mineralogy. The study area is the McAlister Shale Pit in south-central Oklahoma where both the upper and middle sections of the Woodford Shale are exposed and can be lidar-mapped. Lidar results are validated using hand-measured strike and dips of fracture planes, thin sections and mineral chemistry of selected samples using X-ray diffraction (XRD). Complexity of the fracture patterns as well as inaccessibility of multiple locations within the shale pit makes hand-measurement prone to errors and biases; lidar provides an opportunity for less biased and more efficient field mapping. Fracture mapping with lidar is a multi-step process. The lidar data are converted from point clouds into a mesh through triangulation. User-defined parameters such as size and orientation of the individual triangular elements are then used to group similar elements into surfaces. The strike and dip attribute of the simulated surfaces are visualized in an equal area lower hemisphere projection stereonet. Three fracture sets were identified in the upper and middle sections with common orientation but substantially different spatial density. Measured surface attributes and spatial density relations from lidar were validated using their hand-measured counterparts. Thin section analysis suggests that high fracture density in the upper Woodford measured by both the lidar and the hand-measured data could be due to high quartz. A significant finding of this study is the reciprocal relation between lidar intensity and gamma-ray (GR), which is generally used to infer outcrop mineralogy. XRD analysis of representative samples along the common profiles show that both GR and lidar intensity were influenced by the same minerals in essentially opposite ways. Results strongly suggest that the lidar cannot only remotely map the geomorphology, but also the relative mineralogical variations to the first order of approximation.

Staphylococcus aureus recovery from cotton towels.

PubMed

Oller, Anna R; Mitchell, Ashley

2009-04-30

Staphylococcus aureus is an emerging pathogen afflicting healthy individuals without known risk factors, and methicillin-resistant Staphylococcus aureus has been shown to colonize multiple family members sharing households. Because household items such as towels are often shared by family members, this study investigated whether cotton towel absorbency or washing conditions affect Staphylococcus aureus cell viability or cell retention, and whether the levels may be sufficient for person-to-person transmission. Staphylococcus aureus ATCC 25923 was added to a 48 mm(2) template area on three cotton towel types (terry, pima, and Egyptian), and subjected to hand washing, without manual wringing, in three conditions (water only, bleach addition, or liquid detergent addition). Serial dilutions plated onto mannitol salt plates quantified bacteria for inoculations, pre- and post-wash water samples, towel surfaces, and hand transfer. Hand transfer of bacteria was determined on towels immediately, one, 24, and 48 hours post inoculation. Bleach (p < or = .05) was the most effective at reducing bacterial viability on all towel types compared to detergent and water. Although not statistically significant, more Staphylococcus colonies were recovered from higher absorbency towels and from inside directly inoculated template areas. A paired t-test showed a difference between immediate and one-hour CFUs versus 24- and 48-hour recoveries (0.0002) for hand transfers. Cell viability decreased for over 48 hours on towels, but sufficient quantities may remain for colonization. More absorbent towels may harbor more Staphylococci than less absorbent ones, and may serve as a transmission mechanism for the bacterium.

To use or not to use (direct laser interference patterning), that is the question

NASA Astrophysics Data System (ADS)

Lasagni, A. F.; Roch, T.; Berger, J.; Kunze, T.; Lang, V.; Beyer, E.

2015-03-01

Direct Laser Interference Patterning (DLIP) has shown to be a fabrication technology capable of producing large area periodic surface patterns on almost any kind of material. The produced structures have been used in the past to provide surfaces with new enhanced properties. On the other hand, the industrial use of this technology is still at the beginning due to the lack of appropriate and affordable systems, especially for small and medium enterprises. In this paper, the use of DLIP for the fabrication of periodic structures using different structuring strategies and optical concepts is discussed. Different technological challenges are addressed.

Sand fly (Diptera: Psychodidae) abundance and species diversity in relation to environmental factors in parts of coastal plains of southern India.

PubMed

Srinivasan, R; Jambulingam, P; Vanamail, P

2013-07-01

Abundance pattern of sand flies in relation to several environmental factors, such as type of areas, dwellings, landforms, land usage pattern, and surface soil pH, was assessed in 81 areas or villages of Puducherry district, Puducherry Union Territory, located on the coastal plain of southern India, for three seasons, between November 2006 and October 2008, adopting hand-catch method. In total, 1,319 sand fly specimens comprising 12 species under two genera, viz., Phlebotomus and Sergentomyia, were collected. Among them, Phlebotomus (Euphlebotomus) argentipes Annandale & Brunetti, the vector of visceral leishmaniasis in India, was the predominant species in all habitats surveyed. The hierarchical cluster analysis showed that the density of sand flies was 10-fold higher in high-density group and fivefold higher in medium-density group, compared with the no or low-density group. Sand fly density was found to be influenced significantly with the type of areas, dwellings, landforms, land usage pattern, and surface soil pH in different groups. Rural areas located on fluvial landform with alkaline surface soil pH, supporting rice cultivation and luxuriant vegetation, are the most influencing factors that favor sand fly abundance and diversity in this district.

The effect of bracing availability on one-hand isometric force exertion capability.

PubMed

Jones, Monica L H; Reed, Matthew P; Chaffin, Don B

2013-01-01

Environmental obstructions that workers encounter can kinematically limit the postures that they can achieve. However, such obstructions can also provide an opportunity for additional support by bracing with the hand, thigh or other body part. The reaction forces on bracing surfaces, which are in addition to those acting at the feet and task hand, are hypothesised to improve force exertion capability, and become required inputs to biomechanical analysis of tasks with bracing. The effects of kinematic constraints and associated bracing opportunities on isometric hand force were quantified in a laboratory study of 22 men and women. Analyses of one-hand maximal push, pull and lift tasks demonstrated that bracing surfaces available at the thighs and non-task hand enabled participants to exert an average of 43% more force at the task hand. Task hand force direction deviated significantly from the nominal direction for exertions performed with bracing at both medium and low task hand locations. This study quantifies the effect of bracing on kinematically constrained force exertions. Knowledge that appropriate bracing surfaces can substantially increase hand force is critical to the evaluation of task-oriented strength capability. Force estimates may also involve large off-axis components, which have clear implications for ergonomic analyses of manual tasks.

The Application of Surface Potential Test on Hand-making Insulation for Generator Stator End-winding

NASA Astrophysics Data System (ADS)

Lu, Zhu-mao; Liu, Qing; Wang, Tian-zheng; Bai, Lu; Li, Yan-peng

2017-05-01

This paper presents the advantage of surface potential test on hand-making insulation for generator stator end-winding insulation detection, compared with DC or AC withstand voltage test, also details the test principle, connection method and test notes. And through the case, surface potential test on hand-making insulation proved effective for insulation quality detection after generator stator end-winding maintenance, and the experimental data is useful and reliable for the electrical equipment operation and maintenance in the power plant.

High-voltage electrical burn injuries: functional upper extremity assessment.

PubMed

Mazzetto-Betti, K C; Amâncio, A C G; Farina, J A; Barros, M E P M; Fonseca, M C R

2009-08-01

High-voltage electric injuries have many manifestations, and an important complication is the damage of the central/peripheral nervous system. The purpose of this work was to assess the upper limb dysfunction in patients injured by high-voltage current. The evaluation consisted of analysis of patients' records, cutaneous-sensibility threshold, handgrip and pinch strength and a specific questionnaire about upper limb dysfunctions (DASH) in 18 subjects. All subjects were men; the average age at the time of the injury was 38 years. Of these, 72% changed job/retired after the injury. The current entrance was the hand in 94% and grounding in the lower limb in 78%. The average burned surface area (BSA) was 8.6%. The handgrip strength of the injured limb was reduced (p<0.05) and so also that of the three pinch types. The relationship between the handgrip strength and the DASH was statistically significant (p<0.001) as well as the relationship between the three pinch types (p

Effect of hand hygiene and glove use on cleanliness of reusable surgical instruments.

PubMed

Costa, D M; Lopes, L K O; Tipple, A F V; Castillo, R B; Hu, H; Deva, A K; Vickery, K

2017-12-01

During functionality testing and packaging of reusable surgical instruments (RSI) for sterilization, instruments are frequently touched. There is a lack of standards relating to hand hygiene frequency and use of gloves in the sterilizing service unit packing area. To determine the effect of hand hygiene and glove use on maintenance of RSI cleanliness. Following manual and automated cleaning, Halsted-mosquito forceps were assessed for adenosine triphosphate (ATP), protein and microbial contamination after handling with gloved and ungloved but washed hands using an ATP surface swab test, bicinchoninic acid assay, and standard culture plate/broth, respectively. Gram's stain was used to classify the isolates. RSI contamination was assessed immediately following and 1, 2, and 4 h after washing hands. Packing instruments with hands that had been unwashed for 2 or 4 h resulted in a significant increase in contaminating ATP when compared with all other treatment groups (P < 0.05). There was a significant correlation between the time since washing hands, the amount of ATP (r = 0.93; P ≤ 0.001), and the microbial load (r = 0.83; P ≤ 0.001) contaminating the forceps, where the longer the time the hands remained unwashed the higher the contamination. Significantly more contaminating protein was found on forceps handled with ungloved hands that had not been washed for 2 or 4 h (P < 0.001). Critical RSI inspection, assembling, lubricating and packing should be performed using either gloves or within 1 h of washing hands. Copyright © 2017 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Snowstorm Along the China-Mongolia-Russia Borders

NASA Technical Reports Server (NTRS)

2004-01-01

Heavy snowfall on March 12, 2004, across north China's Inner Mongolia Autonomous Region, Mongolia and Russia, caused train and highway traffic to stop for several days along the Russia-China border. This pair of images from the Multi-angle Imaging SpectroRadiometer (MISR) highlights the snow and surface properties across the region on March 13. The left-hand image is a multi-spectral false-color view made from the near-infrared, red, and green bands of MISR's vertical-viewing (nadir) camera. The right-hand image is a multi-angle false-color view made from the red band data of the 46-degree aftward camera, the nadir camera, and the 46-degree forward camera.

About midway between the frozen expanse of China's Hulun Nur Lake (along the right-hand edge of the images) and Russia's Torey Lakes (above image center) is a dark linear feature that corresponds with the China-Mongolia border. In the upper portion of the images, many small plumes of black smoke rise from coal and wood fires and blow toward the southeast over the frozen lakes and snow-covered grasslands. Along the upper left-hand portion of the images, in Russia's Yablonovyy mountain range and the Onon River Valley, the terrain becomes more hilly and forested. In the nadir image, vegetation appears in shades of red, owing to its high near-infrared reflectivity. In the multi-angle composite, open-canopy forested areas are indicated by green hues. Since this is a multi-angle composite, the green color arises not from the color of the leaves but from the architecture of the surface cover. The green areas appear brighter at the nadir angle than at the oblique angles because more of the snow-covered surface in the gaps between the trees is visible. Color variations in the multi-angle composite also indicate angular reflectance properties for areas covered by snow and ice. The light blue color of the frozen lakes is due to the increased forward scattering of smooth ice, and light orange colors indicate rougher ice or snow, which scatters more light in the backward direction.

The Multi-angle Imaging SpectroRadiometer observes the daylit Earth continuously and every 9 days views the entire Earth between 82 degrees north and 82 degrees south latitude. These data products were generated from a portion of the imagery acquired during Terra orbit 22525. The panels cover an area of about 355 kilometers x 380 kilometers, and utilize data from blocks 50 to 52 within World Reference System-2 path 126.

MISR was built and is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

Somatic sensory cortex (SmI) of the prosimian primate Galago crassicaudatus: organization of mechanoreceptive input from the hand in relation to cytoarchitecture.

PubMed

Carlson, M; Welt, C

1980-01-15

Mechanoreceptive input from the hand to the somatic sensory cortex (SmI) of the prosimian primate Galago crassicaudatus was examined with microelectrode mapping methods. In anesthetized animals, low threshold cutaneous input from the hand projects to SmI cortex in a single, complete, somatotopically organized pattern. Within this single pattern, cells with receptive fields on the glabrous skin of the palm, digits and digit tips are located in the rostral half, and cells with RFs on the hairy skin of the dorsal hand and digits are located in the caudal half of the hand areas. The cutaneous hand area is coextensive with the densely granular architectonic region of SmI. Studies of single cells in this region of awake galagos reveal the same pattern of cutaneous input and, in addition, demonstrate the presence of cells responding to joint movement not detected in anesthetized animals. Cells responsive to joint movement are arranged in vertically oriented columns located adjacent to cutaneous columns with receptive fields on the same part of the hand. In anesthetized animals, cells rostral to the granular region, in an area typified by increasing numbers of pyramidal cells in layer V and decreasing numbers of granular cells in upper layers, respond to high threshold stimulation of large areas of the hand. The few cells isolated in this area in awake animals respond to either active or passive hand movements. In such animals, cells caudal to the granular region, in an area characterized as agranular and alaminar cortex, respond to either passive stimulation of single or multiple joints or to active hand movements. These results, together with similar findings in a related prosimian, Nycticebus coucang, emphasize the generality of a single cutaneous hand area in SmI of prosimian species. The demonstration of multiple hand areas corresponding to multiple cytoarchitectonic subdivisions in SmI of Old and New World simians illustrates the increased degree of SmI differentiation from the prosimian to the simian grade of organization. The present results further suggest that determination of the homologues of multiple areas or subdivisions within and surrounding SmI in primates will require comparisons of somatotopy, submodality, sulcal patterns, cytoarchitecture, and connectivity in representative members of prosimian and simian families.

Update of the Accounting Surface Along the Lower Colorado River

USGS Publications Warehouse

Wiele, Stephen M.; Leake, Stanley A.; Owen-Joyce, Sandra J.; McGuire, Emmet H.

2008-01-01

The accounting-surface method was developed in the 1990s by the U.S. Geological Survey, in cooperation with the Bureau of Reclamation, to identify wells outside the flood plain of the lower Colorado River that yield water that will be replaced by water from the river. This method was needed to identify which wells require an entitlement for diversion of water from the Colorado River and need to be included in accounting for consumptive use of Colorado River water as outlined in the Consolidated Decree of the United States Supreme Court in Arizona v. California. The method is based on the concept of a river aquifer and an accounting surface within the river aquifer. The study area includes the valley adjacent to the lower Colorado River and parts of some adjacent valleys in Arizona, California, Nevada, and Utah and extends from the east end of Lake Mead south to the southerly international boundary with Mexico. Contours for the original accounting surface were hand drawn based on the shape of the aquifer, water-surface elevations in the Colorado River and drainage ditches, and hydrologic judgment. This report documents an update of the original accounting surface based on updated water-surface elevations in the Colorado River and drainage ditches and the use of simple, physically based ground-water flow models to calculate the accounting surface in four areas adjacent to the free-flowing river.

Thermal maps of young women and men

NASA Astrophysics Data System (ADS)

Chudecka, Monika; Lubkowska, Anna

2015-03-01

The objective was to use thermal imaging (ThermaCAM SC500) as an effective tool in establishing a thermal map of young participants, with a high diagnostic value for medicine, physiotherapy and sport. A further aim was to establish temperature distributions and ranges on the body surface of the young women and men as standard temperatures for the examined age group, taking into account BMI, body surface area and selected parameters of body fat distribution. The participants included young, healthy and physically active women (n = 100) and men (n = 100). In the women and men, the highest Tmean temperatures were found on the trunk. The warmest were the chest and upper back, then the lower back and abdomen. The lowest Tmean were found in the distal parts of the body, especially on the lower limbs. The results showed that only in the area of the chest was Tmean significantly higher in women than in men. In the areas of the hands (front and back) Tmean were similar for women and men. In the other analyzed body surface areas, Tmean were significantly lower in women. Research showed significant differences in body surface temperature between the women and men. Among the analyzed characteristics, Tmean in the chest, upper back, abdomen, lower back (both in women and men) were mainly correlated with BMI and PBF; the correlations were negative. Difficulties in interpreting changes in temperature in selected body areas in people with various conditions can be associated with the lack of studies on large and representative populations of healthy individuals with normal weight/height parameters. Therefore, it seems that this presented research is a significant practical and cognitive contribution to knowledge on thermoregulation, and may therefore be used as a reference for other studies using thermal imaging in the evaluation of changes in body surface temperatures.

Personal and household hygiene, environmental contamination, and health in undergraduate residence halls in New York City, 2011.

PubMed

Miko, Benjamin A; Cohen, Bevin; Haxall, Katharine; Conway, Laurie; Kelly, Nicole; Stare, Dianne; Tropiano, Christina; Gilman, Allan; Seward, Samuel L; Larson, Elaine

2013-01-01

While several studies have documented the importance of hand washing in the university setting, the added role of environmental hygiene remains poorly understood. The purpose of this study was to characterize the personal and environmental hygiene habits of college students, define the determinants of hygiene in this population, and assess the relationship between reported hygiene behaviors, environmental contamination, and health status. 501 undergraduate students completed a previously validated survey assessing baseline demographics, hygiene habits, determinants of hygiene, and health status. Sixty survey respondents had microbiological samples taken from eight standardized surfaces in their dormitory environment. Bacterial contamination was assessed using standard quantitative bacterial culture techniques. Additional culturing for coagulase-positive Staphylococcus and coliforms was performed using selective agar. While the vast majority of study participants (n = 461, 92%) believed that hand washing was important for infection prevention, there was a large amount of variation in reported personal hygiene practices. More women than men reported consistent hand washing before preparing food (p = .002) and after using the toilet (p = .001). Environmental hygiene showed similar variability although 73.3% (n = 367) of subjects reported dormitory cleaning at least once per month. Contamination of certain surfaces was common, with at least one third of all bookshelves, desks, refrigerator handles, toilet handles, and bathroom door handles positive for >10 CFU of bacteria per 4 cm(2) area. Coagulase-positive Staphylococcus was detected in three participants' rooms (5%) and coliforms were present in six students' rooms (10%). Surface contamination with any bacteria did not vary by frequency of cleaning or frequency of illness (p>.05). Our results suggest that surface contamination, while prevalent, is unrelated to reported hygiene or health in the university setting. Further research into environmental reservoirs of infectious diseases may delineate whether surface decontamination is an effective target of hygiene interventions in this population.

Personal and Household Hygiene, Environmental Contamination, and Health in Undergraduate Residence Halls in New York City, 2011

PubMed Central

Haxall, Katharine; Conway, Laurie; Kelly, Nicole; Stare, Dianne; Tropiano, Christina; Gilman, Allan; Seward, Samuel L.; Larson, Elaine

2013-01-01

Background While several studies have documented the importance of hand washing in the university setting, the added role of environmental hygiene remains poorly understood. The purpose of this study was to characterize the personal and environmental hygiene habits of college students, define the determinants of hygiene in this population, and assess the relationship between reported hygiene behaviors, environmental contamination, and health status. Methods 501 undergraduate students completed a previously validated survey assessing baseline demographics, hygiene habits, determinants of hygiene, and health status. Sixty survey respondents had microbiological samples taken from eight standardized surfaces in their dormitory environment. Bacterial contamination was assessed using standard quantitative bacterial culture techniques. Additional culturing for coagulase-positive Staphylococcus and coliforms was performed using selective agar. Results While the vast majority of study participants (n = 461, 92%) believed that hand washing was important for infection prevention, there was a large amount of variation in reported personal hygiene practices. More women than men reported consistent hand washing before preparing food (p = .002) and after using the toilet (p = .001). Environmental hygiene showed similar variability although 73.3% (n = 367) of subjects reported dormitory cleaning at least once per month. Contamination of certain surfaces was common, with at least one third of all bookshelves, desks, refrigerator handles, toilet handles, and bathroom door handles positive for >10 CFU of bacteria per 4 cm2 area. Coagulase-positive Staphylococcus was detected in three participants' rooms (5%) and coliforms were present in six students' rooms (10%). Surface contamination with any bacteria did not vary by frequency of cleaning or frequency of illness (p>.05). Conclusions Our results suggest that surface contamination, while prevalent, is unrelated to reported hygiene or health in the university setting. Further research into environmental reservoirs of infectious diseases may delineate whether surface decontamination is an effective target of hygiene interventions in this population. PMID:24312303

Novel Test Fixture for Characterizing Microcontacts: Performance and Reliability

DTIC Science & Technology

2013-03-01

limited to the resolution of the measuring instrument [30]. A fractal method, on the other hand, random surface texture is characterized by scale...areas and allows the exposed 1805 to be developed away (f). After the 1805 is developed, the exposed SF-11 is subjected to deep ultra violet light (DUV...separated by a combination of fracture and plasticity [78]. Gold exhibited ductile behavior at both T=150K and T=300K [78, 80]. The difference in

Device for determining frost depth and density

NASA Technical Reports Server (NTRS)

Huneidi, F.

1983-01-01

A hand held device having a forward open window portion adapted to be pushed downwardly into the frost on a surface, and a rear container portion adapted to receive the frost removed from the window area are described. A graph on a side of the container enables an observer to determine the density of the frost from certain measurements noted. The depth of the frost is noted from calibrated lines on the sides of the open window portion.

Resurfacing glabrous skin defects in the hand: the thenar base donor site.

PubMed

Milner, Chris S; Thirkannad, Sunil M

2014-06-01

Defects of the glabrous skin surfaces of the palm and fingers result from numerous causes including larger fingertip injuries, unhealed burns, and after surgery for diverse pathologies. The qualities of glabrous skin are specifically tailored to the functional requirements of high-shear strength and robustness. Despite these unique properties, graft reconstruction of defects in the glabrous regions of the hand is frequently achieved with skin from nonglabrous donor sites such as the medial forearm. Nonglabrous skin has a poor color and texture match for such applications and is frequently associated with tender and unsightly donor scars. We describe our experiences of harvesting full-thickness grafts from the glabrous skin centered over the proximal flexion crease at the level of the metacarpophalangeal joint of the thumb. We have utilized this site to harvest skin grafts of up to 2 cm in width for the resurfacing of small-sized to medium-sized defects on the palmar surfaces of the hands and fingers in 28 patients under both traumatic and elective circumstances. The skin has an excellent type-match to the defect and is quick and easy to harvest due to its adjacent location to the defect. The donor scar matures quickly, and as it lies along the thumb base crease, it runs along one of the least used contact surfaces, thereby limiting the potential discomfort associated with FTSG harvest sites from other areas. Patient satisfaction with the procedure has been high, and it represents a useful alternative to traditional nonglabrous skin graft donor sites for small-sized to medium-sized defects.

Micropattern printing of adhesion, spreading, and migration peptides on poly(tetrafluoroethylene) films to promote endothelialization.

PubMed

Gauvreau, Virginie; Laroche, Gaétan

2005-01-01

We report here the development of an original multistep micropatterning technique for printing peptides on surfaces, based on the ink-jet printer technology. Contrary to most micropatterning methods used nowadays, this technique is advantageous because it allows displaying 2D-arrays of multiple biomolecules. Moreover, this low cost procedure allies the advantages of computer-aided design with high flexibility and reproducibility. A Hewlett-Packard printer was modified to print peptide solutions, and Adobe Illustrator was used as the graphic-editing software to design high-resolution checkerboard-like micropatterns. In a first step, PTFE films were treated with ammonia plasma to introduce amino groups on the surface. These chemical functionalities were reacted with heterobifunctional cross-linker sulfo-succinimidyl 4-(N-maleimidomethyl)cycloexane-1-carboxylate (S-SMCC) to allow the subsequent surface covalent conjugation of various cysteine-modified peptides to the polymer substrate. These peptidic molecules containing RGD and WQPPRARI sequences were selected for their adhesive, spreading, and migrational properties toward endothelial cells. On one hand, our data demonstrated that the initial cell adhesion does not depend on the chemical structure and combination of the peptides covalently bonded either through conventional conjugation or micropatterning. On the other hand, spreading and migration of endothelial cells is clearly enhanced while coconjugating the GRGDS peptide in conjunction with WQPPRARI. This behavior is further improved by micropatterning these peptides on specific areas of the polymer surface.

Transmission of vibration through gloves: effects of contact area.

PubMed

Md Rezali, Khairil Anas; Griffin, Michael J

2017-01-01

For three samples of material (12.5, 25.0 and 37.5 mm diameter) from each of three gloves, the dynamic stiffnesses and the vibration transmissibilities of the materials (to both the palm of the hand and the thenar eminence) were measured at frequencies from 10 to 300 Hz. Additional measurements showed the apparent masses of the hand at the palm and the thenar eminence were independent of contact area at frequencies less than about 40 Hz, but increased with increasing area at higher frequencies. The stiffness and damping of the glove materials increased with increasing area. These changes caused material transmissibilities to the hand to increase with increasing area. It is concluded that the size of the area of contact has a large influence on the transmission of vibration through a glove to the hand. The area of contact should be well-defined and controlled when evaluating the transmission of vibration through gloves. Practitioner Summary: The transmission of vibration through gloves depends on both the dynamic stiffness of glove material and the dynamic response of the hand. Both of these depend on the size of the contact area between a glove material and the hand, which should be taken into account when assessing glove transmissibility.

Assessing possible exposures of ground troops to Agent Orange during the Vietnam War: the use of contemporary military records.

PubMed

Young, Alvin L; Cecil, Paul F; Guilmartin, John F

2004-01-01

Potential exposure of ground troops in Vietnam to Agent Orange and 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) remains controversial despite the passage of 30 years since the Vietnam War. Because of uncertainty over the serum dioxin levels in ground troops at the end of their service in Vietnam, attempts have been made to develop a methodology for characterizing exposure of ground troops in Vietnam to Agent Orange and other herbicides based upon historical reconstruction from military records. Historical information is often useful in evaluating and modeling exposure, but such information should be reasonably accurate, complete, and reliable. This paper reviews the procedures and supporting historical information related to the spraying of herbicides in Vietnam. The historical information is classified into two categories: procedural information and operational information. Procedural information covered the process and procedures followed in spraying herbicides from US Air Force fixed wing aircraft (Operation RANCH HAND) in Vietnam, and included approval procedures for spray missions, the criteria required to conduct a mission, the control exercised by the Forward Air Controller and the Tactical Air Control Center and the characteristics of the equipment used to apply the herbicides. Operational information includes data from the RANCH HAND Daily Air Activities Reports, which included geographic locations of specific spray missions, the amount of herbicide sprayed by a specific mission, reports of battle damage to spray aircraft, reports of fighter aircraft support for aerial spray missions, and any comments, such as reasons for canceling a mission. Historical information demonstrates that herbicide spray missions were carefully planned and that spraying only occurred when friendly forces were not located in the target area. RANCH HAND spray missions were either not approved or cancelled if approved when there were friendly forces in the area designated for spraying. Stringent criteria had to be met before spray missions could be approved. The operational information shows that spray missions for both defoliation and crop destruction were conducted in an extremely hostile environment. Heavy 'fighter suppression' with antipersonnel ordnance was used to minimize the impact of hostile ground fire on RANCH HAND aircraft. Procedures were in place that prohibited movement of troops into sprayed areas immediately after a mission due to the possible presence of unexploded ordnance delivered by fighter aircraft supporting RANCH HAND missions. The optimal nature of the spray equipment and application procedures minimized the possibility of significant spray drift. Conclusions. Few friendly troops were sprayed by fixed wing aircraft during Operation RANCH HAND, which delivered 95% of all defoliants used in Vietnam. Similarly, few troops were sprayed during helicopter or surface-based spray operations, which constituted the remaining 5% of defoliants. Detailed policies and procedures for approval and execution of spray missions ensured that friendly forces were not located in the areas targeted for spraying. Fighter aircraft assigned to accompany each spray mission frequently suppressed much of the hostile fire with bombs and other ordnance. Confirmed clearance of the target area was necessary to avoid friendly casualties. Historical records establish that these policies and procedures were strictly followed. Exposure of troops whether from direct spraying or movement through areas recently sprayed was very unlikely. The wartime military records of troop positions and herbicide operations are valuable for some purposes, but have specific limitations in exposure reconstruction. The completeness and accuracy of the geographic data (maps used by RANCH HAND and military ground units) were dependent upon the inherent precision of the map, the accuracy with which it depicted surface features, and the completeness and accuracy of the information on which it is based. Navigation by the crew using visual orientation and reference to the map was the only means that aircrew on spray missions had for establishing their locations. A Forward Air Controller independent of Operation RANCH HAND was present at the location of each spray target immediately before and during spraying operations to verify the target location and ensure that friendly forces were clear of the target area. Anecdotal reports of direct spraying of troops in Vietnam likely reflect the RANCH HAND missions spraying insecticide for mosquito control at regular intervals from March 1967 through February 1972. Outlook. The distribution and levels of serum dioxin in RANCH HAND veterans and the US Army Chemical Corps Vietnam veterans (the unit responsible for helicopter and ground-based spray operations) are distinguishable from typical levels in the population decades after the Vietnam conflict. An exposure model similar to that proposed in the 2003 report of the Institute of Medicine's Committee on 'Characterizing Exposure of Veterans to Agent Orange and Other Herbicides Used in Vietnam' was tested in 1988 by the Centers for Disease Control and Prevention and found to be a poor predictor of absorbed dose of TCDD. Military records during the Vietnam War lack the precision to determine that troops were directly sprayed with herbicides during Operation RANCH HAND, especially given the procedures in place to ensure clearance of friendly forces from the target area and the lack of elevated serum levels of TCDD in ground troops judged to have operated in heavily sprayed areas.

Hazardous materials emergency response mobile robot

NASA Technical Reports Server (NTRS)

Stone, Henry W. (Inventor); Lloyd, James (Inventor); Alahuzos, George (Inventor)

1992-01-01

A simple or unsophisticated robot incapable of effecting straight-line motion at the end of its arm inserts a key held in its end effector or hand into a door lock with nearly straight-line motion by gently thrusting its back heels downwardly so that it pivots forwardly on its front toes while holding its arm stationary. The relatively slight arc traveled by the robot's hand is compensated by a complaint tool with which the robot hand grips the door key. A visible beam is projected through the axis of the hand or gripper on the robot arm end at an angle to the general direction in which the robot thrusts the gripper forward. As the robot hand approaches a target surface, a video camera on the robot wrist watches the beam spot on the target surface fall from a height proportional to the distance between the robot hand and the target surface until the beam spot is nearly aligned with the top of the robot hand. Holes in the front face of the hand are connected through internal passages inside the arm to an on-board chemical sensor. Full rotation of the hand or gripper about the robot arm's wrist is made possible by slip rings in the wrist which permit passage of the gases taken in through the nose holes in the front of the hand through the wrist regardless of the rotational orientation of the wrist.

Research on Integrated Mapping——A Case Study of Integrated Land Use with Swamp Mapping

NASA Astrophysics Data System (ADS)

Zhang, S.; Yan, F.; Chang, L.

2015-12-01

Unified real estate registration system shows the attention, determination and effort to of CPC Central Committee and State Council on real estate registration in China. However, under current situation, China's real estate registration work made less progress. One of the reasons is that it's hard to express the property right of real estate on one map under the multi-sector management system. Under current multi-sector management system in China, different departments usually just survey and mapping the land type under its jurisdiction. For example, wetland investigation only mapping all kinds of wetland resources but not mapping other resource types. As a result, it cause he problem of coincidence or leak in integration of different results from different departments. As resources of the earth's surface, the total area of forest, grassland, wetland and so on should be equal to the total area of the earth's surface area. However, under the current system, the area of all kinds of resources is not equal to the sum of the earth's surface. Therefore, it is of great importance to express all the resources on one map. On one hand, this is conducive to find out the real area and distribution of resources and avoid the problem of coincidence or leak in integration; On the other hand, it is helpful to study the dynamic change of different resources. Therefore, we first proposed the "integrated mapping" as a solution, and take integrated land use with swamp mapping in Northeast China as an example to investigate the feasibility and difficulty. Study showed that: integrated land use with swamp mapping can be achieved through combining land use survey standards with swamps survey standards and "second mapping" program. Based on the experience of integrated land use with swamp mapping, we point out its reference function on integrated mapping and unified real estate registration system. We concluded that: (1) Comprehending and integrating different survey standard of different resources is the premise of "integrated mapping", (2) We put forward "multiple code" and "multiple interpretation" scheme in order to solve the problem of "attribute overlap", (3) The area of "attribute overlap" can be segmented by a certain ratio to determine the property right in unified real estate registration.

Effect of dialyzer geometry on granulocyte and complement activation.

PubMed

Schaefer, R M; Heidland, A; Hörl, W H

1987-01-01

During hemodialysis with cuprophan membranes, the complement system as well as leukocytes become activated. In order to clarify the role of dialyzer geometry, the effect of hollow-fiber versus flat-sheet dialyzers and of different surface areas on C3a generation and leukocyte degranulation was investigated. Plasma levels of leukocyte elastase in complex with alpha 1-proteinase inhibitor were significantly increased after 1 h (+55%) and 3 h (+62%) of hemodialysis with flat-sheet dialyzers as compared to hollow-fiber devices. In addition, plasma levels of lactoferrin, released from the specific granules of leukocytes during activation, were significantly higher (+42%) 3 h after the onset of dialysis treatment with flat-sheet than with hollow-fiber dialyzers. With respect to surface area, larger dialyzers tended to cause more release of leukocyte elastase as compared to dialyzers with smaller surface areas, irrespectively of the configuration of the dialyzer used. On the other hand, activation of the complement system, as measured by the generation of C3a-desarg, did not differ with both types of configurations. The same held true for leukopenia, which was almost identical for hollow-fiber and flat-sheet dialyzers. From these findings two lines of evidence emerge: First, not only the type of membrane material used in a dialyzer may influence its biocompatibility, but the geometry of the extracorporeal device also determines the degree of compatibility. Hence, the extent of leukocyte activation correlated with both configuration of the dialyzer and surface area of the membrane.(ABSTRACT TRUNCATED AT 250 WORDS)

The influence of anthropometric, kinematic and energetic variables and gender on swimming performance in youth athletes.

PubMed

Morais, Jorge E; Garrido, Nuno D; Marques, Mário C; Silva, António J; Marinho, Daniel A; Barbosa, Tiago M

2013-12-18

(i) gender; (ii) performance and; (iii) gender versus performance interactions in young swimmers' anthropometric, kinematic and energetic variables. One hundred and thirty six young swimmers (62 boys: 12.76 ± 0.72 years old at Tanner stages 1-2 by self-evaluation; and 64 girls: 11.89 ± 0.93 years old at Tanner stages 1-2 by self-evaluation) were evaluated. Performance, anthropometrics, kinematics and energetic variables were selected. There was a non-significant gender effect on performance, body mass, height, arm span, trunk transverse surface area, stroke length, speed fluctuation, swimming velocity, propulsive efficiency, stroke index and critical velocity. A significant gender effect was found for foot surface area, hand surface area and stroke frequency. A significant sports level effect was verified for all variables, except for stroke frequency, speed fluctuation and propulsive efficiency. Overall, swimmers in quartile 1 (the ones with highest sports level) had higher anthropometric dimensions, better stroke mechanics and energetics. These traits decrease consistently throughout following quartiles up to the fourth one (i.e. swimmers with the lowest sports level). There was a non-significant interaction between gender and sports level for all variables. Our main conclusions were as follows: (i) there are non-significant differences in performance, anthropometrics, kinematics and energetics between boys and girls; (ii) swimmers with best performance are taller, have higher surface areas and better stroke mechanics; (iii) there are non-significant interactions between sports level and gender for anthropometrics, kinematics and energetics.

Clusters in Short-term Disease Course in Participants With Primary Dupuytren Disease.

PubMed

Lanting, Rosanne; van den Heuvel, Edwin R; Werker, Paul M N

2016-03-01

The course of Dupuytren disease (DD) is thought to be progressive; however, the course differs for each patient. The purpose of this study was to study the rate and pattern of progression of DD. We prospectively analyzed the course of DD at intervals of 3 to 6 months in 247 Dutch participants with primary DD by measuring the surface area of nodules and cords and the total passive extension deficit. The association between surface area and Tubiana stage was tested with generalized estimating equations. Latent class models were used to study different clusters in changes regarding the course of the disease. The variance in disease course between participants was large. Regarding the change in surface area (in all fingers) and total passive extension deficit (in the ring and little finger), different clusters were observed. Progression of disease was seen but there were also signs of stability and even regression. Patients with a smaller surface area at baseline were more likely to exhibit regression. This study showed that DD is not always progressive and that up to 75% of patients have a different short-term disease course, such as stability or even regression of disease. This should be taken into account when evaluating the effects of treatment for early-phase DD and in the design of future studies. Furthermore, this information may be useful when counseling patients. Prognostic II. Copyright © 2016 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

An Economical Analytical Equation for the Integrated Vertical Overlap of Cumulus and Stratus

NASA Astrophysics Data System (ADS)

Park, Sungsu

2018-03-01

By extending the previously proposed heuristic parameterization, the author derived an analytical equation computing the overlap areas between the precipitation (or radiation) areas and the cloud areas in a cloud system consisting of cumulus and stratus. The new analytical equation is accurate and much more efficient than the previous heuristic equation, which suffers from the truncation error in association with the digitalization of the overlap areas. Global test simulations with the new analytical formula in an offline mode showed that the maximum cumulus overlap simulates more surface precipitation flux than the random cumulus overlap. On the other hand, the maximum stratus overlap simulates less surface precipitation flux than random stratus overlap, which is due to the increase in the evaporation rate of convective precipitation from the random to maximum stratus overlap. The independent precipitation approximation (IPA) marginally decreases the surface precipitation flux, implying that IPA works well with other parameterizations. In contrast to the net production rate of precipitation and surface precipitation flux that increase when the cumulus and stratus are maximally and randomly overlapped, respectively, the global mean net radiative cooling and longwave cloud radiative forcing (LWCF) increase when the cumulus and stratus are randomly overlapped. On the global average, the vertical cloud overlap exerts larger impacts on the precipitation flux than on the radiation flux. The radiation scheme taking the subgrid variability of water vapor between the cloud and clear portions into account substantially increases the global mean LWCF in tropical deep convection and midlatitude storm track regions.

The use of an extended ventilation tube as a countermeasure for EVA-associated upper extremity medical issues

NASA Astrophysics Data System (ADS)

Jones, J. A.; Hoffman, R. B.; Buckland, D. A.; Harvey, C. M.; Bowen, C. K.; Hudy, C. E.; Strauss, S.; Novak, J.; Gernhardt, M. L.

Introduction: Onycholysis due to repetitive activity in the space suit glove during Neutral Buoyancy Laboratory (NBL) training and during spaceflight extravehicular activity (EVA) is a common observation. Moisture accumulates in gloves during EVA task performance and may contribute to the development of pain and damage to the fingernails experienced by many astronauts. The study evaluated the use of a long ventilation tube to determine if improved gas circulation into the hand area could reduce hand moisture and thereby decrease the associated symptoms. Methods: The current Extravehicular Mobility Unit (EMU) was configured with a ventilation tube that extended down a single arm of the crew member (E) and compared with the unventilated arm (C). Skin surface moisture was measured on both hands immediately after glove removal and a questionnaire administered to determine subjective measures. Astronauts ( n=6) were examined pre- and post-run. Results: There were consistent trends in the reduction of relative hydration ratios at dorsum ( C=3.34, E=2.11) and first ring finger joint ( C=2.46, E=1.96) when the ventilation tube was employed. Ventilation appeared more effective on the left versus the right hand, implying an interaction with hand anthropometry and glove fit. Symptom score was lower on the hand that had the long ventilation tube relative to the control hand in 2/6 EVA crew members. Conclusions: Increased ventilation to the hand was effective in reducing the risks of hand and nail discomfort symptoms from moderate to low in one-third of the subjects. Improved design in the ventilation capability of EVA spacesuits is expected to improve efficiency of air flow distribution.

Ultramorphology of the root surface subsequent to hand-ultrasonic simultaneous instrumentation during non-surgical periodontal treatments. An in vitro study

PubMed Central

D. ASPRIELLO, Simone; PIEMONTESE, Matteo; LEVRINI, Luca; SAURO, Salvatore

2011-01-01

Objective The purpose of this study was to investigate the ultramorphology of the root surfaces induced by mechanical instrumentation performed using conventional curettes or piezoelectric scalers when used single-handedly or with a combined technique. Material and Methods Thirty single-rooted teeth were selected and divided into 3 groups: Group A, instrumentation with curettes; Group B instrumentation with titanium nitride coated periodontal tip mounted in a piezoelectric handpiece; Group C, combined technique with curette/ultrasonic piezoelectric instrumentation. The specimens were processed and analyzed using confocal and scanning electron microscopy. Differences between the different groups of instrumentation were determined using Pearson’s χ 2 with significance predetermined at α=0.001. Results Periodontal scaling and root planing performed with curettes, ultrasonic or combined instrumentation induced several morphological changes on the root surface. The curettes produced a compact and thick multilayered smear layer, while the morphology of the root surfaces after ultrasonic scaler treatment appeared irregular with few grooves and a thin smear layer. The combination of curette/ultrasonic instrumentation showed exposed root dentin tubules with a surface morphology characterized by the presence of very few grooves and slender remnants of smear layer which only partially covered the root dentin. In some cases, it was also possible to observe areas with exposed collagen fibrils. Conclusion The curette-ultrasonic simultaneous instrumentation may combine the beneficial effects of each instrument in a single technique creating a root surface relatively free from the physical barrier of smear layer and dentin tubules orifices partial occlusion. PMID:21437474

Artificial limb representation in amputees

PubMed Central

van den Heiligenberg, Fiona M Z; Orlov, Tanya; Macdonald, Scott N; Duff, Eugene P; Henderson Slater, David; Beckmann, Christian F; Johansen-Berg, Heidi; Culham, Jody C; Makin, Tamar R

2018-01-01

Abstract The human brain contains multiple hand-selective areas, in both the sensorimotor and visual systems. Could our brain repurpose neural resources, originally developed for supporting hand function, to represent and control artificial limbs? We studied individuals with congenital or acquired hand-loss (hereafter one-handers) using functional MRI. We show that the more one-handers use an artificial limb (prosthesis) in their everyday life, the stronger visual hand-selective areas in the lateral occipitotemporal cortex respond to prosthesis images. This was found even when one-handers were presented with images of active prostheses that share the functionality of the hand but not necessarily its visual features (e.g. a ‘hook’ prosthesis). Further, we show that daily prosthesis usage determines large-scale inter-network communication across hand-selective areas. This was demonstrated by increased resting state functional connectivity between visual and sensorimotor hand-selective areas, proportional to the intensiveness of everyday prosthesis usage. Further analysis revealed a 3-fold coupling between prosthesis activity, visuomotor connectivity and usage, suggesting a possible role for the motor system in shaping use-dependent representation in visual hand-selective areas, and/or vice versa. Moreover, able-bodied control participants who routinely observe prosthesis usage (albeit less intensively than the prosthesis users) showed significantly weaker associations between degree of prosthesis observation and visual cortex activity or connectivity. Together, our findings suggest that altered daily motor behaviour facilitates prosthesis-related visual processing and shapes communication across hand-selective areas. This neurophysiological substrate for prosthesis embodiment may inspire rehabilitation approaches to improve usage of existing substitutionary devices and aid implementation of future assistive and augmentative technologies. PMID:29534154

Artificial limb representation in amputees.

PubMed

van den Heiligenberg, Fiona M Z; Orlov, Tanya; Macdonald, Scott N; Duff, Eugene P; Henderson Slater, David; Beckmann, Christian F; Johansen-Berg, Heidi; Culham, Jody C; Makin, Tamar R

2018-05-01

The human brain contains multiple hand-selective areas, in both the sensorimotor and visual systems. Could our brain repurpose neural resources, originally developed for supporting hand function, to represent and control artificial limbs? We studied individuals with congenital or acquired hand-loss (hereafter one-handers) using functional MRI. We show that the more one-handers use an artificial limb (prosthesis) in their everyday life, the stronger visual hand-selective areas in the lateral occipitotemporal cortex respond to prosthesis images. This was found even when one-handers were presented with images of active prostheses that share the functionality of the hand but not necessarily its visual features (e.g. a 'hook' prosthesis). Further, we show that daily prosthesis usage determines large-scale inter-network communication across hand-selective areas. This was demonstrated by increased resting state functional connectivity between visual and sensorimotor hand-selective areas, proportional to the intensiveness of everyday prosthesis usage. Further analysis revealed a 3-fold coupling between prosthesis activity, visuomotor connectivity and usage, suggesting a possible role for the motor system in shaping use-dependent representation in visual hand-selective areas, and/or vice versa. Moreover, able-bodied control participants who routinely observe prosthesis usage (albeit less intensively than the prosthesis users) showed significantly weaker associations between degree of prosthesis observation and visual cortex activity or connectivity. Together, our findings suggest that altered daily motor behaviour facilitates prosthesis-related visual processing and shapes communication across hand-selective areas. This neurophysiological substrate for prosthesis embodiment may inspire rehabilitation approaches to improve usage of existing substitutionary devices and aid implementation of future assistive and augmentative technologies.

Pramoxine

MedlinePlus

... your hands. Clean the affected area with mild soap and warm water. Rinse thoroughly. Pat affected area ... your hands. Clean affected rectal area with mild soap and warm water. Rinse thoroughly. Gently dry by ...

Interplay between structure, stoichiometry, and electron transfer dynamics in SILAR-based quantum dot-sensitized oxides.

PubMed

Wang, Hai; Barceló, Irene; Lana-Villarreal, Teresa; Gómez, Roberto; Bonn, Mischa; Cánovas, Enrique

2014-10-08

We quantify the rate and efficiency of picosecond electron transfer (ET) from PbS nanocrystals, grown by successive ionic layer adsorption and reaction (SILAR), into a mesoporous SnO2 support. Successive SILAR deposition steps allow for stoichiometry- and size-variation of the QDs, characterized using transmission electron microscopy. Whereas for sulfur-rich (p-type) QD surfaces substantial electron trapping at the QD surface occurs, for lead-rich (n-type) QD surfaces, the QD trapping channel is suppressed and the ET efficiency is boosted. The ET efficiency increase achieved by lead-rich QD surfaces is found to be QD-size dependent, increasing linearly with QD surface area. On the other hand, ET rates are found to be independent of both QD size and surface stoichiometry, suggesting that the donor-acceptor energetics (constituting the driving force for ET) are fixed due to Fermi level pinning at the QD/oxide interface. Implications of our results for QD-sensitized solar cell design are discussed.

Hemispheric Dominance for Stereognosis in a Patient With an Infarct of the Left Postcentral Sensory Hand Area.

PubMed

Moll, Jorge; de Oliveira-Souza, Ricardo

2017-09-01

The concept of left hemispheric dominance for praxis, speech, and language has been one of the pillars of neurology since the mid-19th century. In 1906, Hermann Oppenheim reported a patient with bilateral stereoagnosia (astereognosis) caused by a left parietal lobe tumor and proposed that the left hemisphere was also dominant for stereognosis. Surprisingly, few cases of bilateral stereoagnosia caused by a unilateral cerebral lesion have been documented in the literature since then. Here we report a 75-year-old right-handed man who developed bilateral stereoagnosia after suffering a small infarct in the crown of the left postcentral gyrus. He could not recognize objects with either hand, but retained the ability to localize stimuli applied to the palm of his left (ipsilesional) hand. He was severely disabled in ordinary activities requiring the use of his hands. The lesion corresponded to Brodmann area 1, where probabilistic anatomic, functional, and electrophysiologic studies have located one of the multiple somatosensory representations of the hand. The lesion was in a strategic position to interrupt both the processing of afferent tactile information issuing from the primary somatosensory cortex (areas 3a and 3b) and the forward higher-order processing in area 2, the secondary sensory cortex, and the contralateral area 1. The lesion also deprived the motor hand area of its afferent regulation from the sensory hand area (grasping), while leaving intact the visuomotor projections from the occipital cortex (reaching). Our patient supports Oppenheim's proposal that the left postcentral gyrus of some individuals is dominant for stereognosis.

The coil orientation dependency of the electric field induced by TMS for M1 and other brain areas.

PubMed

Janssen, Arno M; Oostendorp, Thom F; Stegeman, Dick F

2015-05-17

The effectiveness of transcranial magnetic stimulation (TMS) depends highly on the coil orientation relative to the subject's head. This implies that the direction of the induced electric field has a large effect on the efficiency of TMS. To improve future protocols, knowledge about the relationship between the coil orientation and the direction of the induced electric field on the one hand, and the head and brain anatomy on the other hand, seems crucial. Therefore, the induced electric field in the cortex as a function of the coil orientation has been examined in this study. The effect of changing the coil orientation on the induced electric field was evaluated for fourteen cortical targets. We used a finite element model to calculate the induced electric fields for thirty-six coil orientations (10 degrees resolution) per target location. The effects on the electric field due to coil rotation, in combination with target site anatomy, have been quantified. The results confirm that the electric field perpendicular to the anterior sulcal wall of the central sulcus is highly susceptible to coil orientation changes and has to be maximized for an optimal stimulation effect of the motor cortex. In order to obtain maximum stimulation effect in areas other than the motor cortex, the electric field perpendicular to the cortical surface in those areas has to be maximized as well. Small orientation changes (10 degrees) do not alter the induced electric field drastically. The results suggest that for all cortical targets, maximizing the strength of the electric field perpendicular to the targeted cortical surface area (and inward directed) optimizes the effect of TMS. Orienting the TMS coil based on anatomical information (anatomical magnetic resonance imaging data) about the targeted brain area can improve future results. The standard coil orientations, used in cognitive and clinical neuroscience, induce (near) optimal electric fields in the subject-specific head model in most cases.

Increased functional connectivity between cortical hand areas and praxis network associated with training-related improvements in non-dominant hand precision drawing.

PubMed

Philip, Benjamin A; Frey, Scott H

2016-07-01

Chronic forced use of the non-dominant left hand yields substantial improvements in the precision and quality of writing and drawing. These changes may arise from increased access by the non-dominant (right) hemisphere to dominant (left) hemisphere mechanisms specialized for end-point precision control. To evaluate this prediction, 22 healthy right-handed adults underwent resting state functional connectivity (FC) MRI scans before and after 10 days of training on a left hand precision drawing task. 89% of participants significantly improved left hand speed, accuracy, and smoothness. Smoothness gains were specific to the trained left hand and persistent: 6 months after training, 71% of participants exhibited above-baseline movement smoothness. Contrary to expectations, we found no evidence of increased FC between right and left hemisphere hand areas. Instead, training-related improvements in left hand movement smoothness were associated with increased FC between both sensorimotor hand areas and a left-lateralized parieto-prefrontal network implicated in manual praxis. By contrast, skill retention at 6 months was predicted by changes including decreased FC between the representation of the trained left hand and bilateral sensorimotor, parietal, and premotor cortices, possibly reflecting consolidation and a disengagement of early learning processes. These data indicate that modest amounts of training (<200min total) can induce substantial, persistent improvements the precision and quality of non-dominant hand control in healthy adults, supported by strengthened connectivity between bilateral sensorimotor hand areas and a left-lateralized parieto-prefrontal praxis network. Copyright © 2016 Elsevier Ltd. All rights reserved.

Evaluation of hygiene practices and microbiological status of ready-to-eat vegetable salads in Spanish school canteens.

PubMed

Rodríguez-Caturla, Magdevis Y; Valero, Antonio; Carrasco, Elena; Posada, Guiomar D; García-Gimeno, Rosa M; Zurera, Gonzalo

2012-08-30

This study was conducted in eight Spanish school canteens during the period 2008-2009. Food handlers' practices, kitchen equipment, hygiene/sanitation conditions and handling practices were evaluated using checklists. In parallel, the microbiological quality and safety of ready-to-eat (RTE) vegetable salads were assessed. In addition, food contact surfaces and environmental air quality of different areas were analysed. The study determined the relationship between the microbiological quality of RTE foods and food handling practices, together with the degree of contamination of working surfaces and environmental contamination of processing and distribution areas. Some deficiencies were found regarding the use and change of gloves, hand-washing and cleanliness of working surfaces. The microbial levels detected in the foods examined indicated the absence of pathogens in the samples analysed. Surface counts were higher on cutting boards and faucets, showing insufficient cleanliness procedures. This study constitutes a descriptive analysis of the hygiene/sanitation conditions implemented in food service systems in eight Spanish school canteens. The results should help risk managers to better define control measures to be adopted in order to prevent foodborne infections. Copyright © 2012 Society of Chemical Industry.

What is the most efficient respiratory organ for the loricariid air-breathing fish Pterygoplichthys anisitsi, gills or stomach? A quantitative morphological study.

PubMed

da Cruz, André Luis; Fernandes, Marisa Narciso

2016-12-01

The purpose of the present study was to evaluate the morphometric respiratory potential of gills compared to the stomach in obtaining oxygen for aerobic metabolism in Pterygoplichthys anisitsi, a facultative air-breathing fish. The measurements were done using stereological methods. The gills showed greater total volume, volume-to-body mass ratio, potential surface area, and surface-to-volume ratio than the stomach. The water-blood diffusion barrier of the gills is thicker than the air-blood diffusion barrier of the stomach. Taken together, the surface area, the surface-to-volume ratio and the diffusion distance for O 2 transfer from the respiratory medium to blood yield a greater diffusing capacity for gills than for the stomach, suggesting greater importance of aquatic respiration in this species. On the other hand, water breathing is energetically more expensive than breathing air. Under severe hypoxic conditions, O 2 uptake by the stomach is more efficient than by the gills, although the stomach has a much lower diffusing capacity. Thus, P. anisitsi uses gills under normoxic conditions but the stomach may also support aerobic metabolism depending on environmental conditions. Copyright © 2016 Elsevier GmbH. All rights reserved.

Volga Delta and the Caspian Sea

NASA Technical Reports Server (NTRS)

2002-01-01

Russia's Volga River is the largest river system in Europe, draining over 1.3 million square kilometers of catchment area into the Caspian Sea. The brackish Caspian is Earth's largest landlocked water body, and its isolation from the world's oceans has enabled the preservation of several unique animal and plant species. The Volga provides most of the Caspian's fresh water and nutrients, and also discharges large amounts of sediment and industrial waste into the relatively shallow northern part of the sea. These images of the region were captured by the Multi-angle Imaging SpectroRadiometer on October 5, 2001, during Terra orbit 9567. Each image represents an area of approximately 275 kilometers x 376 kilometers.

The left-hand image is from MISR's nadir (vertical-viewing) camera, and shows how light is reflected at red, green, and blue wavelengths. The right-hand image is a false color composite of red-band imagery from MISR's 60-degree backward, nadir, and 60-degree forward-viewing cameras, displayed as red, green, and blue, respectively. Here, color variations indicate how light is reflected at different angles of view. Water appears blue in the right-hand image, for example, because sun glitter makes smooth, wet surfaces look brighter at the forward camera's view angle. The rougher-textured vegetated wetlands near the coast exhibit preferential backscattering, and consequently appear reddish. A small cloud near the center of the delta separates into red, green, and blue components due to geometric parallax associated with its elevation above the surface.

Other notable features within the images include several linear features located near the Volga Delta shoreline. These long, thin lines are artificially maintained shipping channels, dredged to depths of at least 2 meters. The crescent-shaped Kulaly Island, also known as Seal Island, is visible near the right-hand edge of the images.

MISR was built and is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

Survey, Testing, and Documentation, Assembly and Offense Areas, Live Fire Maneuver Range, Fort Irwin, San Bernardino County, California.

DTIC Science & Technology

1982-06-01

1953). Nonetheless, the concept of an early pre-projectile cultural stratum in North America related, in part, to the Paleolithic in Europe has been...assignment of age based on similarities in form to the Old World Paleolithic is insuffi- cient (see Simpson 1960:33-35, 1961:34). While the surface as- pects...appearance the similarity between some stage 2 biface forms (Photograph 17) and the Acheulian hand axe of Old World Paleolithic periods is remarkable

Effects of gamma radiation on hard dental tissues of albino rats: investigation by light microscopy.

PubMed

El-Faramawy, Nabil; Ameen, Reham; El-Haddad, Khaled; El-Zainy, Medhat

2013-08-01

The present work aims at studying the effect of gamma radiation on the hard dental tissues. Eighty adult male albino rats with weights of about 250 g were used. The rats were irradiated at 0.2, 0.5, 1.0, 2.0, 4.0 and 6.0 Gy whole-body gamma doses. The effects on hard dental tissue samples were investigated after 48 h in histological and ground sections using light microscopy. Areas of acid phosphatase activity were detected using tartrate-resistant acid phosphatase (TRAP) stains. Observation of histological sections revealed disturbance in predentin thickness and odontoblastic layer as the irradiation dose increased. In cementum, widened cementocytes lacunae were occasionally detected even with low irradiated doses. On the other hand, relatively homogenous enamel was detected with darkened areas in enamel surface at doses over than 0.5 Gy. TRAP-positive cells were detected on the surface of the dentin of irradiated groups as well as cementum surface. Minimal detectable changes were observed in ground sections.

Prevalence of hand osteoarthritis and knee osteoarthritis in Kashin-Beck disease endemic areas and non Kashin-Beck disease endemic areas: A status survey

PubMed Central

Song, QuanQuan; Liu, Yun Qi; Sun, Li Yan; Deng, Qing; Wang, Shao Ping; Cao, Yan Hong; Zhang, Xue Ying; Jiang, Yuan Yuan; Lv, Hong Yan; Duan, Li Bin; Yu, Jun

2018-01-01

Osteoarthritis (OA) is a considerable health problem worldwide, and the prevalence of OA varies in different regions. In this study, the prevalence of OA in Kashin-Beck disease (KBD) and non-KBD endemic areas was examined, respectively. According to monitoring data, 4 types of regions (including none, mild, moderate and high KBD endemic areas) in Heilongjiang and Jilin provinces were selected. All local residents were eligible for inclusion criteria have undergone X-ray images of hands and anteroposterior image of knees. A total of 1673 cases were collected, 1446 cases were analyzed after removing the KBD patients (227). The overall hand OA and knee OA detection rates were 33.3% (481/1446) and 56.6% (818/1446), respectively. After being standardized by age, the detection rate of hand OA in the KBD endemic areas was significantly higher than that in the non-endemic endemic areas. Differently, there was no significant difference in the detection rates of knee OA between the KBD endemic areas and the non-endemic area. The correlation coefficient between the severity of OA and the severity of knee OA was 0.358 and 0.197 in the KBD and non-KBD endemic areas, respectively. Where the KBD historical prevalence level was higher, the severity of the residents’ hand OA was more serious. The detection rates of hand OA and knee OA increased with age. The detection rate of knee OA increased with the increase in body mass index. The prevalence of hand OA was closely related to the pathogenic factors of Kashin-Beck disease, and the prevalence of knee OA had no significant correlation with KBD pathogenic factors. PMID:29320581

Hazardous materials emergency response mobile robot

NASA Technical Reports Server (NTRS)

Stone, Henry W. (Inventor); Lloyd, James W. (Inventor); Alahuzos, George A. (Inventor)

1995-01-01

A simple or unsophisticated robot incapable of effecting straight-line motion at the end of its arm is presented. This robot inserts a key held in its end effector or hand into a door lock with nearly straight-line motion by gently thrusting its back heels downwardly so that it pivots forwardly on its front toes while holding its arm stationary. The relatively slight arc traveled by the robot's hand is compensated by a complaint tool with which the robot hand grips the door key. A visible beam is projected through the axis of the hand or gripper on the robot arm end at an angle to the general direction in which the robot thrusts the gripper forward. As the robot hand approaches a target surface, a video camera on the robot wrist watches the beam spot on the target surface fall from a height proportional to the distance between the robot hand and the target surface until the beam spot is nearly aligned with the top of the robot hand. Holes in the front face of the hand are connected through internal passages inside the arm to an on-board chemical sensor. Full rotation of the hand or gripper about the robot arm's wrist is made possible by slip rings in the wrist which permit passage of the gases taken in through the nose holes in the front of the hand through the wrist regardless of the rotational orientation of the wrist.

Three Software Tools for Viewing Sectional Planes, Volume Models, and Surface Models of a Cadaver Hand.

PubMed

Chung, Beom Sun; Chung, Min Suk; Shin, Byeong Seok; Kwon, Koojoo

2018-02-19

The hand anatomy, including the complicated hand muscles, can be grasped by using computer-assisted learning tools with high quality two-dimensional images and three-dimensional models. The purpose of this study was to present up-to-date software tools that promote learning of stereoscopic morphology of the hand. On the basis of horizontal sectioned images and outlined images of a male cadaver, vertical planes, volume models, and surface models were elaborated. Software to browse pairs of the sectioned and outlined images in orthogonal planes and software to peel and rotate the volume models, as well as a portable document format (PDF) file to select and rotate the surface models, were produced. All of the software tools were downloadable free of charge and usable off-line. The three types of tools for viewing multiple aspects of the hand could be adequately employed according to individual needs. These new tools involving the realistic images of a cadaver and the diverse functions are expected to improve comprehensive knowledge of the hand shape. © 2018 The Korean Academy of Medical Sciences.

Three Software Tools for Viewing Sectional Planes, Volume Models, and Surface Models of a Cadaver Hand

PubMed Central

2018-01-01

Background The hand anatomy, including the complicated hand muscles, can be grasped by using computer-assisted learning tools with high quality two-dimensional images and three-dimensional models. The purpose of this study was to present up-to-date software tools that promote learning of stereoscopic morphology of the hand. Methods On the basis of horizontal sectioned images and outlined images of a male cadaver, vertical planes, volume models, and surface models were elaborated. Software to browse pairs of the sectioned and outlined images in orthogonal planes and software to peel and rotate the volume models, as well as a portable document format (PDF) file to select and rotate the surface models, were produced. Results All of the software tools were downloadable free of charge and usable off-line. The three types of tools for viewing multiple aspects of the hand could be adequately employed according to individual needs. Conclusion These new tools involving the realistic images of a cadaver and the diverse functions are expected to improve comprehensive knowledge of the hand shape. PMID:29441756

Cytomegalovirus survival and transferability and the effectiveness of common hand-washing agents against cytomegalovirus on live human hands.

PubMed

Stowell, Jennifer D; Forlin-Passoni, Daniela; Radford, Kay; Bate, Sheri L; Dollard, Sheila C; Bialek, Stephanie R; Cannon, Michael J; Schmid, D Scott

2014-01-01

Congenital cytomegalovirus (CMV) transmission can occur when women acquire CMV while pregnant. Infection control guidelines may reduce risk for transmission. We studied the duration of CMV survival after application of bacteria to the hands and after transfer from the hands to surfaces and the effectiveness of cleansing with water, regular and antibacterial soaps, sanitizer, and diaper wipes. Experiments used CMV AD169 in saliva at initial titers of 1 × 10(5) infectious particles/ml. Samples from hands or surfaces (points between 0 and 15 min) were placed in culture and observed for at least 2 weeks. Samples were also tested using CMV real-time PCR. After application of bacteria to the hands, viable CMV was recovered from 17/20 swabs at 0 min, 18/20 swabs at 1 min, 5/20 swabs at 5 min, and 4/20 swabs at 15 min. After transfer, duration of survival was at least 15 min on plastic (1/2 swabs), 5 min on crackers and glass (3/4 swabs), and 1 min or less on metal and cloth (3/4 swabs); no viable virus was collected from wood, rubber, or hands. After cleansing, no viable virus was recovered using water (0/22), plain soap (0/20), antibacterial soap (0/20), or sanitizer (0/22). Viable CMV was recovered from 4/20 hands 10 min after diaper wipe cleansing. CMV remains viable on hands for sufficient times to allow transmission. CMV may be transferred to surfaces with reduced viability. Hand-cleansing methods were effective at eliminating viable CMV from hands.

Cytomegalovirus Survival and Transferability and the Effectiveness of Common Hand-Washing Agents against Cytomegalovirus on Live Human Hands

PubMed Central

Stowell, Jennifer D.; Forlin-Passoni, Daniela; Radford, Kay; Bate, Sheri L.; Dollard, Sheila C.; Bialek, Stephanie R.; Cannon, Michael J.

2014-01-01

Congenital cytomegalovirus (CMV) transmission can occur when women acquire CMV while pregnant. Infection control guidelines may reduce risk for transmission. We studied the duration of CMV survival after application of bacteria to the hands and after transfer from the hands to surfaces and the effectiveness of cleansing with water, regular and antibacterial soaps, sanitizer, and diaper wipes. Experiments used CMV AD169 in saliva at initial titers of 1 × 105 infectious particles/ml. Samples from hands or surfaces (points between 0 and 15 min) were placed in culture and observed for at least 2 weeks. Samples were also tested using CMV real-time PCR. After application of bacteria to the hands, viable CMV was recovered from 17/20 swabs at 0 min, 18/20 swabs at 1 min, 5/20 swabs at 5 min, and 4/20 swabs at 15 min. After transfer, duration of survival was at least 15 min on plastic (1/2 swabs), 5 min on crackers and glass (3/4 swabs), and 1 min or less on metal and cloth (3/4 swabs); no viable virus was collected from wood, rubber, or hands. After cleansing, no viable virus was recovered using water (0/22), plain soap (0/20), antibacterial soap (0/20), or sanitizer (0/22). Viable CMV was recovered from 4/20 hands 10 min after diaper wipe cleansing. CMV remains viable on hands for sufficient times to allow transmission. CMV may be transferred to surfaces with reduced viability. Hand-cleansing methods were effective at eliminating viable CMV from hands. PMID:24185855

Study on induced strain in direct nanoimprint lithography

NASA Astrophysics Data System (ADS)

Watanabe, Kenta; Iida, Tatsuya; Yasuda, Masaaki; Kawata, Hiroaki; Hirai, Yoshihiko

2018-06-01

The induced shear strain distribution in a polymer film is investigated by computational study in a direct nanoimprint process. The effects of the polymer thickness, mold pattern shape such as rectangular, triangular or overcut pattern shape, and the coefficient of friction between the mold and the polymer are studied by computational work. As the coefficient of friction increases, the induced shear strain increases along the mold surface. Depending on the polymer thickness, the shear strain is induced in the residual and/or pattern area. In the triangular pattern, the strain is induced in the pattern central area. The results suggest that shear stress remains in the triangular pattern area in the direct nanoimprint process. On the other hand, the rectangular pattern is suitable for suppressing the induced strain inside the pattern.

Environmental arsenic exposure of schoolchildren in a former tin mining and smelting community of southern Thailand.

PubMed

Vitayavirasak, Banjong; Rakwong, Kittiya; Chatchawej, Warangkana

2005-01-01

Risk behavior and environmental sources of exposure to arsenic for 10-year-old schoolchildren were studied in a high exposure area and a low exposure area of Ron Phibun Subdistrict, Ron Phibun District, Nakhon Si Thammarat Province and compared to those in a control area. Arsenic concentrations of surface soil, ambient air and drinking water to which subjects in the high exposure group, the low exposure group and the control group were exposed, were significantly different (p < 0.05). Similarly, urinary concentrations of total arsenic and the sum of inorganic arsenic and its metabolites were significantly higher in the study groups than the control group. The arsenic content of locally grown agricultural produce was small with the exception of freshwater snails (Sinotaia ingallsiana). Drinking water and surface soil were found to be the main sources of exposure. The exposure was mediated by the subjects' risk behavior, such as playing with soil and no hand-washing before eating. The estimated cancer risk from arsenic for the schoolchildren in the study area was between 10(-5)-10(-6) which meant that their risk of developing cancer was probable. Measures to reduce the cancer risk are recommended.

Electromechanical hand incorporates touch sensors and trigger function

NASA Technical Reports Server (NTRS)

Dane, D. H.

1970-01-01

Electromechanical hand incorporates touch sensors, concealed fingers, and a structure that allows the hand to hold a tool on a flat surface. The hands can be mounted on most types of existing manipulators either directly or by means of modified mounting brackets.

Influence of activated carbon characteristics on toluene and hexane adsorption: Application of surface response methodology

NASA Astrophysics Data System (ADS)

Izquierdo, Mª Teresa; de Yuso, Alicia Martínez; Valenciano, Raquel; Rubio, Begoña; Pino, Mª Rosa

2013-01-01

The objective of this study was to evaluate the adsorption capacity of toluene and hexane over activated carbons prepared according an experimental design, considering as variables the activation temperature, the impregnation ratio and the activation time. The response surface methodology was applied to optimize the adsorption capacity of the carbons regarding the preparation conditions that determine the physicochemical characteristics of the activated carbons. The methodology of preparation produced activated carbons with surface areas and micropore volumes as high as 1128 m2/g and 0.52 cm3/g, respectively. Moreover, the activated carbons exhibit mesoporosity, ranging from 64.6% to 89.1% the percentage of microporosity. The surface chemistry was characterized by TPD, FTIR and acid-base titration obtaining different values of surface groups from the different techniques because the limitation of each technique, but obtaining similar trends for the activated carbons studied. The exhaustive characterization of the activated carbons allows to state that the measured surface area does not explain the adsorption capacity for either toluene or n-hexane. On the other hand, the surface chemistry does not explain the adsorption results either. A compromise between physical and chemical characteristics can be obtained from the appropriate activation conditions, and the response surface methodology gives the optimal activated carbon to maximize adsorption capacity. Low activation temperature, intermediate impregnation ratio lead to high toluene and n-hexane adsorption capacities depending on the activation time, which a determining factor to maximize toluene adsorption.

Controls of structural inheritance on orogenic curvature and foreland basin sedimentation: Insights from the Przemyśl area, Western Carpathians

NASA Astrophysics Data System (ADS)

Szaniawski, Rafał; Mazzoli, Stefano; Jankowski, Leszek

2017-10-01

Orogenic curvatures can have various origins and are widely debated worldwide. In the Poland-Ukraine border area, the Outer Western Carpathians are characterized by a marked curvature. The origin of this curvature was analysed by integrating stratigraphic information with structural constraints and anisotropy of the magnetic susceptibility (AMS) data. Hangingwall frontal ramp domains are characterized by a relatively simple deformation dominated by layer-parallel shortening and folding around a regional NW-SE trending axis, recorded by an AMS lineation with a similar trend. On the other hand, the N-S trending hangingwall oblique ramp domain is characterized by maximum AMS axes recording transpressional strain either dominated by simple shear (sub-horizontal AMS lineation) or pure shear (steeply plunging AMS lineation) components. Early Miocene basin inversion with two distinct depocentres created a number of different detachment surfaces and thickness variations for the sedimentary successions involved in thrusting. The main depocentre of the Lower-Middle Miocene foredeep was originally located in the recess area of the curved Carpathian front. On the other hand, the occurrence of a salient to the west resulted in the axial zone of the foreland flexure being filled with allochthonous units, thereby dramatically reducing the accommodation space for foredeep sediments in this area. Our results suggest that thrust-belt geometry was controlled by the inherited Mesozoic extensional basin architecture.

Space Shuttle Reusable Solid Rocket Motor (RSRM) Hand Cleaning Solvent Replacement at Kennedy Space Center (KSC)

NASA Technical Reports Server (NTRS)

Keen, Jill M.; DeWeese, Darrell C.; Key, Leigh W.

1997-01-01

At Kennedy Space Center (KSC), Thiokol Corporation provides the engineering to assemble and prepare the Space Shuttle Reusable Solid Rocket Motor (RSRM) for launch. This requires hand cleaning over 86 surfaces including metals, adhesives, rubber and electrical insulations, various painted surfaces and thermal protective materials. Due to the phase-out of certain ozone depleting chemical (ODC) solvents, all RSRM hand wipe operations being performed at KSC using l,l,1-trichloroethane (TCA) were eliminated. This presentation summarizes the approach used and the data gathered in the effort to eliminate TCA from KSC hand wipe operations.

Comparison and assessment of semi-automatic image segmentation in computed tomography scans for image-guided kidney surgery.

PubMed

Glisson, Courtenay L; Altamar, Hernan O; Herrell, S Duke; Clark, Peter; Galloway, Robert L

2011-11-01

Image segmentation is integral to implementing intraoperative guidance for kidney tumor resection. Results seen in computed tomography (CT) data are affected by target organ physiology as well as by the segmentation algorithm used. This work studies variables involved in using level set methods found in the Insight Toolkit to segment kidneys from CT scans and applies the results to an image guidance setting. A composite algorithm drawing on the strengths of multiple level set approaches was built using the Insight Toolkit. This algorithm requires image contrast state and seed points to be identified as input, and functions independently thereafter, selecting and altering method and variable choice as needed. Semi-automatic results were compared to expert hand segmentation results directly and by the use of the resultant surfaces for registration of intraoperative data. Direct comparison using the Dice metric showed average agreement of 0.93 between semi-automatic and hand segmentation results. Use of the segmented surfaces in closest point registration of intraoperative laser range scan data yielded average closest point distances of approximately 1 mm. Application of both inverse registration transforms from the previous step to all hand segmented image space points revealed that the distance variability introduced by registering to the semi-automatically segmented surface versus the hand segmented surface was typically less than 3 mm both near the tumor target and at distal points, including subsurface points. Use of the algorithm shortened user interaction time and provided results which were comparable to the gold standard of hand segmentation. Further, the use of the algorithm's resultant surfaces in image registration provided comparable transformations to surfaces produced by hand segmentation. These data support the applicability and utility of such an algorithm as part of an image guidance workflow.

Modeling of scale-dependent bacterial growth by chemical kinetics approach.

PubMed

Martínez, Haydee; Sánchez, Joaquín; Cruz, José-Manuel; Ayala, Guadalupe; Rivera, Marco; Buhse, Thomas

2014-01-01

We applied the so-called chemical kinetics approach to complex bacterial growth patterns that were dependent on the liquid-surface-area-to-volume ratio (SA/V) of the bacterial cultures. The kinetic modeling was based on current experimental knowledge in terms of autocatalytic bacterial growth, its inhibition by the metabolite CO2, and the relief of inhibition through the physical escape of the inhibitor. The model quantitatively reproduces kinetic data of SA/V-dependent bacterial growth and can discriminate between differences in the growth dynamics of enteropathogenic E. coli, E. coli JM83, and Salmonella typhimurium on one hand and Vibrio cholerae on the other hand. Furthermore, the data fitting procedures allowed predictions about the velocities of the involved key processes and the potential behavior in an open-flow bacterial chemostat, revealing an oscillatory approach to the stationary states.

Creating Nanotechnicians for the 21st Century Workplace

NASA Astrophysics Data System (ADS)

Burke, Michael; Jean, Kristi; Brown, Cheryl; Barrett, Rick; Leopold, Carrie

The North Dakota State College of Science (NDSCS) Nanoscience Technology Training Program was designed and implemented to meet the growing demand for technicians skilled in nanofabrication, surface analysis and production of various micro and nano-scale products. The program emphasizes hands-on training and utilizes a state-of-the-art Applied Science and Advanced Manufacturing Training Laboratory to develop the KSA’s (knowledge, skills, attitudes) needed by industry. Two-year Associate in Applied Science degree, diploma and certificate tracks are offered in four industry focus areas; nanotechnology, microelectronics technology, bio-fuels technology and biotechnology. Students learn to work in multidisciplinary teams on design, prototyping, analysis and manufacturing processes of products. The program also hosts an extensive hands-on outreach program which interacted with over 8000 secondary school science students and 500 teachers in the first 12 months of operation.

"First-person view" of pathogen transmission and hand hygiene - use of a new head-mounted video capture and coding tool.

PubMed

Clack, Lauren; Scotoni, Manuela; Wolfensberger, Aline; Sax, Hugo

2017-01-01

Healthcare workers' hands are the foremost means of pathogen transmission in healthcare, but detailed hand trajectories have been insufficiently researched so far. We developed and applied a new method to systematically document hand-to-surface exposures (HSE) to delineate true hand transmission pathways in real-life healthcare settings. A head-mounted camera and commercial coding software were used to capture ten active care episodes by eight nurses and two physicians and code HSE type and duration using a hierarchical coding scheme. We identified HSE sequences of particular relevance to infectious risks for patients based on the WHO 'Five Moments for Hand Hygiene'. The study took place in a trauma intensive care unit in a 900-bed university hospital in Switzerland. Overall, the ten videos totaled 296.5 min and featured eight nurses and two physicians. A total of 4222 HSE were identified (1 HSE every 4.2 s), which concerned bare (79%) and gloved (21%) hands. The HSE inside the patient zone ( n  = 1775; 42%) included mobile objects (33%), immobile surfaces (5%), and patient intact skin (4%), while HSE outside the patient zone ( n  = 1953; 46%) included HCW's own body (10%), mobile objects (28%), and immobile surfaces (8%). A further 494 (12%) events involved patient critical sites. Sequential analysis revealed 291 HSE transitions from outside to inside patient zone, i.e. "colonization events", and 217 from any surface to critical sites, i.e. "infection events". Hand hygiene occurred 97 times, 14 (5% adherence) times at colonization events and three (1% adherence) times at infection events. On average, hand rubbing lasted 13 ± 9 s. The abundance of HSE underscores the central role of hands in the spread of potential pathogens while hand hygiene occurred rarely at potential colonization and infection events. Our approach produced a valid video and coding instrument for in-depth analysis of hand trajectories during active patient care that may help to design more efficient prevention schemes.

Control of Precision Grip Force in Lifting and Holding of Low-Mass Objects

PubMed Central

Kimura, Daisuke; Kadota, Koji; Ito, Taro

2015-01-01

Few studies have investigated the control of grip force when manipulating an object with an extremely small mass using a precision grip, although some related information has been provided by studies conducted in an unusual microgravity environment. Grip-load force coordination was examined while healthy adults (N = 17) held a moveable instrumented apparatus with its mass changed between 6 g and 200 g in 14 steps, with its grip surface set as either sandpaper or rayon. Additional measurements of grip-force-dependent finger-surface contact area and finger skin indentation, as well as a test of weight discrimination, were also performed. For each surface condition, the static grip force was modulated in parallel with load force while holding the object of a mass above 30 g. For objects with mass smaller than 30 g, on the other hand, the parallel relationship was changed, resulting in a progressive increase in grip-to-load force (GF/LF) ratio. The rayon had a higher GF/LF force ratio across all mass levels. The proportion of safety margin in the static grip force and normalized moment-to-moment variability of the static grip force were also elevated towards the lower end of the object mass for both surfaces. These findings indicate that the strategy of grip force control for holding objects with an extremely small mass differs from that with a mass above 30 g. The data for the contact area, skin indentation, and weight discrimination suggest that a decreased level of cutaneous feedback signals from the finger pads could have played some role in a cost function in efficient grip force control with low-mass objects. The elevated grip force variability associated with signal-dependent and internal noises, and anticipated inertial force on the held object due to acceleration of the arm and hand, could also have contributed to the cost function. PMID:26376484

A comparative scanning electron microscopy study between hand instrument, ultrasonic scaling and erbium doped:Yttirum aluminum garnet laser on root surface: A morphological and thermal analysis

PubMed Central

Mishra, Mitul Kumar; Prakash, Shobha

2013-01-01

Background and Objectives: Scaling and root planing is one of the most commonly used procedures for the treatment of periodontal diseases. Removal of calculus using conventional hand instruments is incomplete and rather time consuming. In search of more efficient and less difficult instrumentation, investigators have proposed lasers as an alternative or as adjuncts to scaling and root planing. Hence, the purpose of the present study was to evaluate the effectiveness of erbium doped: Yttirum aluminum garnet (Er:YAG) laser scaling and root planing alone or as an adjunct to hand and ultrasonic instrumentation. Subjects and Methods: A total of 75 freshly extracted periodontally involved single rooted teeth were collected. Teeth were randomly divided into five treatment groups having 15 teeth each: Hand scaling only, ultrasonic scaling only, Er:YAG laser scaling only, hand scaling + Er:YAG laser scaling and ultrasonic scaling + Er:YAG laser scaling. Specimens were subjected to scanning electron microscopy and photographs were evaluated by three examiners who were blinded to the study. Parameters included were remaining calculus index, loss of tooth substance index, roughness loss of tooth substance index, presence or absence of smear layer, thermal damage and any other morphological damage. Results: Er:YAG laser treated specimens showed similar effectiveness in calculus removal to the other test groups whereas tooth substance loss and tooth surface roughness was more on comparison with other groups. Ultrasonic treated specimens showed better results as compared to other groups with different parameters. However, smear layer presence was seen more with hand and ultrasonic groups. Very few laser treated specimens showed thermal damage and morphological change. Interpretation and Conclusion: In our study, ultrasonic scaling specimen have shown root surface clean and practically unaltered. On the other hand, hand instrument have produced a plane surface, but removed more tooth structure. The laser treated specimens showed rough surfaces without much residual deposit or any other sign of morphological change. PMID:24015009

Underwater cleaning techniqued used for removal of zebra mussels at the FitzPatrick Nuclear Power Plant

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hobbs, B.; Kahabka, J.

1995-06-01

This paper discusses the use of a mechanical brush cleaning technology recently used to remove biofouling from the Circulating Water (CW) System at New York Power Authority`s James A. FitzPatrick Nuclear Power Plant. The FitzPatrick plant had previously used chemical molluscicide to treat zebra mussels in the CW system. Full system treatment was performed in 1992 with limited forebay/screenwell treatment in 1993. The New York Power Authority (NYPA) decided to conduct a mechanical cleaning of the intake system in 1994. Specific project objectives included: (1) Achieve a level of surface cleaniness greater than 98%; (2) Remove 100% of debris, bothmore » existing sediment and debris generated as a result of cleaning; (3) Inspect all surfaces and components, identifying any problem areas; (4) Complete the task in a time frame within the 1994-95 refueling outage schedule window, and; (5) Determine if underwater mechanical cleaning is a cost-effective zebra mussel control method suitable for future application at FitzPatrick. A pre-cleaning inspection, including underwater video photography, was conducted of each area. Cleaning was accomplished using diver-controlled, multi-brush equipment included the electro-hydraulic powered Submersible Cleaning and Maintenance Platform (SCAMP), and several designs of hand-held machines. The brushes swept all zebra mussels off surfaces, restoring concrete and metal substrates to their original condition. Sensitive areas including pump housings, standpipes, sensor piping and chlorine injection tubing, were cleaned without degradation. Submersible vortex vacuum pumps were used to remove debris from the cavity. More than 46,000 ft{sup 2} of surface area was cleaned and over 460 cubic yards of dewatered debris were removed. As each area was completed, a post-clean inspection with photos and video was performed.« less

Bilateral Symmetry of Distortions of Tactile Size Perception.

PubMed

Longo, Matthew R; Ghosh, Arko; Yahya, Tasneem

2015-01-01

The perceived distance between touches on the limbs is generally bigger for distances oriented across the width of the limb than for distances oriented along the length of the limb. The present study aimed to investigate the coherence of such distortions of tactile size perception across different skin surfaces. We investigated distortions of tactile size perception on the dorsal and palmar surfaces of both the left and right hands as well as the forehead. Participants judged which of two tactile distances felt larger. One distance was aligned with the proximodistal axis (along the body), the other with the mediolateral axis (across the body). Clear distortions were found on all five skin surfaces, with stimuli oriented across the width of the body being perceived as farther apart than those oriented along the length of the body. Consistent with previous results, distortions were smaller on the palmar than on the dorsal hand surface. Distortion on the forehead was intermediate between the dorsal and palmar surfaces. There were clear correlations between distortion on the left and right hands, for both the dorsal and palmar skin surfaces. In contrast, within each hand, there was no significant correlation between the two skin surfaces. Distortion on the forehead was not significantly correlated with that on any of the other skin surfaces. These results provide evidence for bilaterally symmetric representations underlying tactile size perception. © The Author(s) 2015.

Comparison of Standard Culture-Based Method to Culture-Independent Method for Evaluation of Hygiene Effects on the Hand Microbiome.

PubMed

Zapka, C; Leff, J; Henley, J; Tittl, J; De Nardo, E; Butler, M; Griggs, R; Fierer, N; Edmonds-Wilson, S

2017-03-28

Hands play a critical role in the transmission of microbiota on one's own body, between individuals, and on environmental surfaces. Effectively measuring the composition of the hand microbiome is important to hand hygiene science, which has implications for human health. Hand hygiene products are evaluated using standard culture-based methods, but standard test methods for culture-independent microbiome characterization are lacking. We sampled the hands of 50 participants using swab-based and glove-based methods prior to and following four hand hygiene treatments (using a nonantimicrobial hand wash, alcohol-based hand sanitizer [ABHS], a 70% ethanol solution, or tap water). We compared results among culture plate counts, 16S rRNA gene sequencing of DNA extracted directly from hands, and sequencing of DNA extracted from culture plates. Glove-based sampling yielded higher numbers of unique operational taxonomic units (OTUs) but had less diversity in bacterial community composition than swab-based sampling. We detected treatment-induced changes in diversity only by using swab-based samples ( P < 0.001); we were unable to detect changes with glove-based samples. Bacterial cell counts significantly decreased with use of the ABHS ( P < 0.05) and ethanol control ( P < 0.05). Skin hydration at baseline correlated with bacterial abundances, bacterial community composition, pH, and redness across subjects. The importance of the method choice was substantial. These findings are important to ensure improvement of hand hygiene industry methods and for future hand microbiome studies. On the basis of our results and previously published studies, we propose recommendations for best practices in hand microbiome research. IMPORTANCE The hand microbiome is a critical area of research for diverse fields, such as public health and forensics. The suitability of culture-independent methods for assessing effects of hygiene products on microbiota has not been demonstrated. This is the first controlled laboratory clinical hand study to have compared traditional hand hygiene test methods with newer culture-independent characterization methods typically used by skin microbiologists. This study resulted in recommendations for hand hygiene product testing, development of methods, and future hand skin microbiome research. It also demonstrated the importance of inclusion of skin physiological metadata in skin microbiome research, which is atypical for skin microbiome studies. Copyright © 2017 Zapka et al.

Different responses of chlorophyll-a concentration and Sea Surface Temperature (SST) on southeasterly wind blowing in the Sunda Strait

NASA Astrophysics Data System (ADS)

Wirasatriya, A.; Kunarso; Maslukah, L.; Satriadi, A.; Armanto, R. D.

2018-03-01

During southeast monsoon, along the western coast of Sumatra Island and southern coast of Java Island are known as the coastal upwelling areas denoted by the occurrence of Sea Surface Temperature (SST) cooling and chlorophyll-a blooming. Located between Sumatra and Java Islands, Sunda Strait waters may give different response to the southeasterly wind blowing above. Using SST and chlorophyll-a data obtained from daily MODIS level 3 during 2006–2016, this study demonstrated the evidence on how bathymetry and topography modified the effect of southeasterly wind on the spatial variability of SST and chlorophyll-a. All datasets were composed into monthly and monthly climatology. The area in the center of Sunda Strait had the lowest chlorophyll-a concentration and the warmest SST during the peak of upwelling season. The deep bottom topography and the absence of barrier land prevented the generation of wind driven coastal upwelling. However, the chlorophyll-a concentration in this area had the highest correlation with the wind speed which means that the variation of chlorophyll-a concentration in this area was highly depended on the variability of wind. On the other hand, the areas with shallow bathymetry and in front of Panaitan and Java Islands had higher chlorophyll-a concentration and cooler SSTs.

Soil moisture variation patterns observed in Hand County, South Dakota

NASA Technical Reports Server (NTRS)

Jones, E. B.; Owe, M.; Schmugge, T. J. (Principal Investigator)

1981-01-01

Soil moisture data were taken during 1976 (April, June, October), 1977 (April, May, June), and 1978 (May, June, July) Hand County, South Dakota as part of the ground truth used in NASA's aircraft experiments to study the use of microwave radiometers for the remote sensing of soil moisture. The spatial variability observed on the ground during each of the sampling events was studied. The data reported are the mean gravimetric soil moisture contained in three surface horizon depths: 0 to 2.5, 0 to 5 and 0 to 10 cm. The overall moisture levels ranged from extremely dry conditions in June 1976 to very wet in May 1978, with a relatively even distribution of values within that range. It is indicated that well drained sites have to be partitioned from imperfectly drained areas when attempting to characterize the general moisture profile throughout an area of varying soil and cover type conditions. It is also found that the variability in moisture content is greatest in the 0 to 2.5 cm measurements and decreases as the measurements are integrated over a greater depth. It is also determined that the sampling intensity of 10 measurements per km is adequate to estimate the mean moisture with an uncertainty of + or - 3 percent under average moisture conditions in areas of moderate to good drainage.

Thermal effectiveness of different IR radiators employed in rheumatoid hand therapy as assessed by thermovisual examination.

PubMed

Rutkowski, Radosław; Straburzyńska-Lupa, Anna; Korman, Paweł; Romanowski, Wojciech; Gizińska, Małgorzata

2011-01-01

We conducted a thermovisual comparison of mean hand surface temperature changes upon local heating with two different IR sources. Sixty-six patients with rheumatoid arthritis (47 women and 19 men; average age, 56.1 ± 8.6 years) were subjected to topical heat therapy for one hand with either the standard IR radiator (SIR) or the water filter IRA (wIRA). The surface temperature of the dorsal side of both hands was measured, and thermal images were taken before and up to 2 h after treatment. At 1 min after treatment, SIR application increased the surface skin temperature of the heated hand from 31.5 ± 1.9 to 35.0 ± 1.9 °C (P<0.05), while wIRA increased it from 32.1 ± 1.6 to 34.2 ± 1.1 °C (P<0.05). Constant decline in temperature was observed immediately after treatment, with the temperatures reaching baseline in about 30 and 120 min after wIRA and SIR treatment, respectively. Similar temperature changes were observed in the heated hands for wIRA and SIR, except at 1 min after treatment. Changes in the untreated hands indicated contralateral reaction. The temperature of the warmed hand showed a correlation to the body mass index. © 2011 The Authors. Photochemistry and Photobiology © 2011 The American Society of Photobiology.

Integration of multi-sensor data to measure soil surface changes

NASA Astrophysics Data System (ADS)

Eltner, Anette; Schneider, Danilo

2016-04-01

Digital elevation models (DEM) of high resolution and accuracy covering a suitable sized area of interest can be a promising approach to help understanding the processes of soil erosion. Thereby, the plot under investigation should remain undisturbed. The fragile marl landscape in Andalusia (Spain) is especially prone to soil detachment and transport with unique sediment connectivity characteristics due to the soil properties and climatic conditions. A 600 m² field plot is established and monitored during three field campaigns (Sep. 2013, Nov. 2013 and Feb. 2014). Unmanned aerial vehicle (UAV) photogrammetry and terrestrial laser scanning (TLS) are suitable tools to generate high resolution topography data that describe soil surface changes at large field plots. Thereby, the advantages of both methods are utilised in a synergetic manner. On the one hand, TLS data is assumed to comprise a higher reliability regarding consistent error behaviour than DEMs derived from overlapping UAV images. Therefore, global errors (e.g. dome effect) and local errors (e.g. DEM blunders due to erroneous image matching) within the UAV data are assessed with the DEMs produced by TLS. Furthermore, TLS point clouds allow for fast and reliable filtering of vegetation spots, which is not as straightforward within the UAV data due to known image matching problems in areas displaying plant cover. On the other hand, systematic DEM errors linked to TLS are detected and possibly corrected utilising the DEMs reconstructed from overlapping UAV images. Furthermore, TLS point clouds are filtered corresponding to the degree of point quality, which is estimated from parameters of the scan geometry (i.e. incidence angle and footprint size). This is especially relevant for this study because the area of interest is located at gentle hillslopes that are prone to soil erosion. Thus, the view of the scanning device onto the surface results in an adverse angle, which is solely slightly improved by the usage of a 4 m high tripod. Surface roughness is considered as a further parameter to evaluate the TLS point quality. The filtering tool allows for choosing each data point either from the TLS or UAV data corresponding to the data acquisition geometry and surface properties. The filtered points are merged into one point cloud, which is finally processed to reduce remaining data noise. DEM analysis reveals a continuous decrease of soil surface roughness after tillage, the reappearance of former wheel tracks and local patterns of erosion as well as accumulation.

General introduction: Liquid and solid (materials, main properties and applications …)

NASA Astrophysics Data System (ADS)

Zabler, Simon

2014-10-01

A general introduction about the diversity of foam structures is given with focus onto the structural, mechanical and dynamical properties at hand. Two classes of materials are addressed: liquid and semi-solid foams, on the one hand, solid foams, on the other hand. The latter can be subdivided into metallic, ceramic and organic foams, depending on the nature of the solid skeleton that supports the overall cell structure. Solid foams generally stem from the concept of mechanical light-weight structures, but they can just as well be employed for their large surface area as well as for their acoustic and thermal properties. Modern biomaterials use tailored ceramic or organo-ceramic foams as bone scaffolds, whereas hierarchically micro- and nanoporous structures are being used by chemistry to control catalytic reactions. Future materials design and development is going to rely increasingly on natural and synthetic foam structures and properties, be it food, thermal insulators or car frames, thus giving a promising outlook onto the foam research and development that is about to come. xml:lang="fr"

Bias Correction of MODIS AOD using DragonNET to obtain improved estimation of PM2.5

NASA Astrophysics Data System (ADS)

Gross, B.; Malakar, N. K.; Atia, A.; Moshary, F.; Ahmed, S. A.; Oo, M. M.

2014-12-01

MODIS AOD retreivals using the Dark Target algorithm is strongly affected by the underlying surface reflection properties. In particular, the operational algorithms make use of surface parameterizations trained on global datasets and therefore do not account properly for urban surface differences. This parameterization continues to show an underestimation of the surface reflection which results in a general over-biasing in AOD retrievals. Recent results using the Dragon-Network datasets as well as high resolution retrievals in the NYC area illustrate that this is even more significant at the newest C006 3 km retrievals. In the past, we used AERONET observation in the City College to obtain bias-corrected AOD, but the homogeneity assumptions using only one site for the region is clearly an issue. On the other hand, DragonNET observations provide ample opportunities to obtain better tuning the surface corrections while also providing better statistical validation. In this study we present a neural network method to obtain bias correction of the MODIS AOD using multiple factors including surface reflectivity at 2130nm, sun-view geometrical factors and land-class information. These corrected AOD's are then used together with additional WRF meteorological factors to improve estimates of PM2.5. Efforts to explore the portability to other urban areas will be discussed. In addition, annual surface ratio maps will be developed illustrating that among the land classes, the urban pixels constitute the largest deviations from the operational model.

Speech-associated gestures, Broca’s area, and the human mirror system

PubMed Central

Skipper, Jeremy I.; Goldin-Meadow, Susan; Nusbaum, Howard C.; Small, Steven L

2009-01-01

Speech-associated gestures are hand and arm movements that not only convey semantic information to listeners but are themselves actions. Broca’s area has been assumed to play an important role both in semantic retrieval or selection (as part of a language comprehension system) and in action recognition (as part of a “mirror” or “observation–execution matching” system). We asked whether the role that Broca’s area plays in processing speech-associated gestures is consistent with the semantic retrieval/selection account (predicting relatively weak interactions between Broca’s area and other cortical areas because the meaningful information that speech-associated gestures convey reduces semantic ambiguity and thus reduces the need for semantic retrieval/selection) or the action recognition account (predicting strong interactions between Broca’s area and other cortical areas because speech-associated gestures are goal-direct actions that are “mirrored”). We compared the functional connectivity of Broca’s area with other cortical areas when participants listened to stories while watching meaningful speech-associated gestures, speech-irrelevant self-grooming hand movements, or no hand movements. A network analysis of neuroimaging data showed that interactions involving Broca’s area and other cortical areas were weakest when spoken language was accompanied by meaningful speech-associated gestures, and strongest when spoken language was accompanied by self-grooming hand movements or by no hand movements at all. Results are discussed with respect to the role that the human mirror system plays in processing speech-associated movements. PMID:17533001

30 CFR 57.7053 - Moving hand-held drills.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Moving hand-held drills. 57.7053 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface and Underground § 57.7053 Moving hand-held drills. Before hand-held...

30 CFR 57.7053 - Moving hand-held drills.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Moving hand-held drills. 57.7053 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface and Underground § 57.7053 Moving hand-held drills. Before hand-held...

30 CFR 57.7053 - Moving hand-held drills.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Moving hand-held drills. 57.7053 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface and Underground § 57.7053 Moving hand-held drills. Before hand-held...

30 CFR 57.7053 - Moving hand-held drills.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Moving hand-held drills. 57.7053 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface and Underground § 57.7053 Moving hand-held drills. Before hand-held...

30 CFR 57.7053 - Moving hand-held drills.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Moving hand-held drills. 57.7053 Section 57... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-UNDERGROUND METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling-Surface and Underground § 57.7053 Moving hand-held drills. Before hand-held...

30 CFR 57.12033 - Hand-held electric tools.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hand-held electric tools. 57.12033 Section 57.12033 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Surface and Underground § 57.12033 Hand-held electric tools. Hand-held electric tools shall not be...

30 CFR 57.12033 - Hand-held electric tools.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hand-held electric tools. 57.12033 Section 57.12033 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Surface and Underground § 57.12033 Hand-held electric tools. Hand-held electric tools shall not be...

30 CFR 57.12033 - Hand-held electric tools.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hand-held electric tools. 57.12033 Section 57.12033 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Surface and Underground § 57.12033 Hand-held electric tools. Hand-held electric tools shall not be...

30 CFR 57.12033 - Hand-held electric tools.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hand-held electric tools. 57.12033 Section 57.12033 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Surface and Underground § 57.12033 Hand-held electric tools. Hand-held electric tools shall not be...

30 CFR 57.12033 - Hand-held electric tools.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hand-held electric tools. 57.12033 Section 57.12033 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND NONMETAL... Surface and Underground § 57.12033 Hand-held electric tools. Hand-held electric tools shall not be...

On femtosecond laser shock peening of stainless steel AISI 316

NASA Astrophysics Data System (ADS)

Hoppius, Jan S.; Kukreja, Lalit M.; Knyazeva, Marina; Pöhl, Fabian; Walther, Frank; Ostendorf, Andreas; Gurevich, Evgeny L.

2018-03-01

In this paper we report on the competition in metal surface hardening between the femtosecond shock peening on the one hand, and formation of laser-induced periodic surface structures (LIPSS) and surface oxidation on the other hand. Peening of the stainless steel AISI 316 due to shock loading induced by femtosecond laser ablation was successfully demonstrated. However, for some range of processing parameters, surface erosion due to LIPSS and oxidation seems to dominate over the peening effect. Strategies to increase the peening efficiency are discussed.

Feedforward and recurrent processing in scene segmentation: electroencephalography and functional magnetic resonance imaging.

PubMed

Scholte, H Steven; Jolij, Jacob; Fahrenfort, Johannes J; Lamme, Victor A F

2008-11-01

In texture segregation, an example of scene segmentation, we can discern two different processes: texture boundary detection and subsequent surface segregation [Lamme, V. A. F., Rodriguez-Rodriguez, V., & Spekreijse, H. Separate processing dynamics for texture elements, boundaries and surfaces in primary visual cortex of the macaque monkey. Cerebral Cortex, 9, 406-413, 1999]. Neural correlates of texture boundary detection have been found in monkey V1 [Sillito, A. M., Grieve, K. L., Jones, H. E., Cudeiro, J., & Davis, J. Visual cortical mechanisms detecting focal orientation discontinuities. Nature, 378, 492-496, 1995; Grosof, D. H., Shapley, R. M., & Hawken, M. J. Macaque-V1 neurons can signal illusory contours. Nature, 365, 550-552, 1993], but whether surface segregation occurs in monkey V1 [Rossi, A. F., Desimone, R., & Ungerleider, L. G. Contextual modulation in primary visual cortex of macaques. Journal of Neuroscience, 21, 1698-1709, 2001; Lamme, V. A. F. The neurophysiology of figure ground segregation in primary visual-cortex. Journal of Neuroscience, 15, 1605-1615, 1995], and whether boundary detection or surface segregation signals can also be measured in human V1, is more controversial [Kastner, S., De Weerd, P., & Ungerleider, L. G. Texture segregation in the human visual cortex: A functional MRI study. Journal of Neurophysiology, 83, 2453-2457, 2000]. Here we present electroencephalography (EEG) and functional magnetic resonance imaging data that have been recorded with a paradigm that makes it possible to differentiate between boundary detection and scene segmentation in humans. In this way, we were able to show with EEG that neural correlates of texture boundary detection are first present in the early visual cortex around 92 msec and then spread toward the parietal and temporal lobes. Correlates of surface segregation first appear in temporal areas (around 112 msec) and from there appear to spread to parietal, and back to occipital areas. After 208 msec, correlates of surface segregation and boundary detection also appear in more frontal areas. Blood oxygenation level-dependent magnetic resonance imaging results show correlates of boundary detection and surface segregation in all early visual areas including V1. We conclude that texture boundaries are detected in a feedforward fashion and are represented at increasing latencies in higher visual areas. Surface segregation, on the other hand, is represented in "reverse hierarchical" fashion and seems to arise from feedback signals toward early visual areas such as V1.

Hand-Clap Songs across the Curriculum

ERIC Educational Resources Information Center

Batchelor, Katherine E.; Bintz, William P.

2012-01-01

This teaching tip focuses on using hand-clapping to teach content area material across the curriculum. We begin with a brief history of hand-clap songs, followed by a rationale for using them in content area literacy. Then, we describe the instructional lesson, share samples that resulted, and discuss lesson extensions. Our goal is to have…

Environmentally compatible hand wipe cleaning solvents

NASA Technical Reports Server (NTRS)

Clayton, Catherine P.; Kovach, Michael P.

1995-01-01

Several solvents of environmental concern have previously been used for hand wipe cleaning of SRB surfaces, including 1,1,1-trichloroethane, perchloroethylene, toluene, xylene, and MEK. USBI determined the major types of surfaces involved, and qualification requirements of replacement cleaning agents. Nineteen environmentally compatible candidates were tested on 33 material substrates with 26 types of potential surface contaminants, involving over 7,000 individual evaluations. In addition to the cleaning performance evaluation, bonding, compatibility, and corrosion tests were conducted. Results showed that one cleaner was not optimum for all surfaces. In most instances, some of the candidates cleaned better than the 1,1,1-trichloroethane baseline control. Aqueous cleaners generally cleaned better, and were more compatible with nonmetallic materials, such as paints, plastics, and elastomers. Organic base cleaners were better on metal surfaces. Five cleaners have been qualified and are now being implemented in SRB hand wipe cleaning operations.

Effect of sulfate ions on the crystallization and photocatalytic activity of TiO2/diatomite composite photocatalyst

NASA Astrophysics Data System (ADS)

Zhang, Jinjun; Wang, Xiaoyan; Wang, Jimei; Wang, Jing; Ji, Zhijiang

2016-01-01

TiO2 nanoparticles were immobilized on diatomite by hydrolysis-deposition method using titanium tetrachloride as precursor. The effect of sulfate ions on the crystallization and photocatalytic activity of TiO2/diatomite composite photocatalyst was characterized by TG-DSC, XRD, BET surface area, SEM, FT-IR spectroscopy, XPS and UV-vis diffuse reflectance spectra. The results indicate that addition of a small amount of sulfate ions promotes the formation of anatase phase and inhibits the transformation from anatase to rutile. On the other hand, sulfate ions immobilized on the surface of TiO2/diatomite have strong affinity for electrons, capturing the photo-generated electrons, which hinders the recombination of electrons and holes.

Typhoon Ioke in the Western Pacific

NASA Technical Reports Server (NTRS)

2006-01-01

[figure removed for brevity, see original site] [figure removed for brevity, see original site] Microwave ImageVisible Light Image

These infrared, microwave, and visible images were created with data retrieved by the Atmospheric Infrared Sounder (AIRS) on NASA's Aqua satellite.

Infrared Image Because infrared radiation does not penetrate through clouds, AIRS infrared images show either the temperature of the cloud tops or the surface of the Earth in cloud-free regions. The lowest temperatures (in purple) are associated with high, cold cloud tops that make up the top of the storm. In cloud-free areas the AIRS instrument will receive the infrared radiation from the surface of the Earth, resulting in the warmest temperatures (orange/red).

Microwave Image In the AIRS microwave imagery, deep blue areas in storms show where the most precipitation occurs, or where ice crystals are present in the convective cloud tops. Outside of these storm regions, deep blue areas may also occur over the sea surface due to its low radiation emissivity. On the other hand, land appears much warmer due to its high radiation emissivity.

In the AIRS microwave imagery, deep blue areas in storms show where the most precipitation occurs, or where ice crystals are present in the convective cloud tops. Outside of these storm regions, deep blue areas may also occur over the sea surface due to its low radiation emissivity. On the other hand, land appears much warmer due to its high radiation emissivity.

Microwave radiation from Earth's surface and lower atmosphere penetrates most clouds to a greater or lesser extent depending upon their water vapor, liquid water and ice content. Precipitation, and ice crystals found at the cloud tops where strong convection is taking place, act as barriers to microwave radiation. Because of this barrier effect, the AIRS microwave sensor detects only the radiation arising at or above their location in the atmospheric column. Where these barriers are not present, the microwave sensor detects radiation arising throughout the air column and down to the surface. Liquid surfaces (oceans, lakes and rivers) have 'low emissivity' (the signal isn't as strong) and their radiation brightness temperature is therefore low. Thus the ocean also appears 'low temperature' in the AIRS microwave images and is assigned the color blue. Therefore deep blue areas in storms show where the most precipitation occurs, or where ice crystals are present in the convective cloud tops. Outside of these storm regions, deep blue areas may also occur over the sea surface due to its low radiation emissivity. Land appears much warmer due to its high radiation emissivity.

Vis/NIR Image The AIRS instrument suite contains a sensor that captures radiation in four bands of the visible/near-infrared portion of the electromagetic spectrum. Data from three of these bands are combined to create 'visible' images similar to a snapshot taken with your camera.

The Atmospheric Infrared Sounder Experiment, with its visible, infrared, and microwave detectors, provides a three-dimensional look at Earth's weather. Working in tandem, the three instruments can make simultaneous observations all the way down to the Earth's surface, even in the presence of heavy clouds. With more than 2,000 channels sensing different regions of the atmosphere, the system creates a global, 3-D map of atmospheric temperature and humidity and provides information on clouds, greenhouse gases, and many other atmospheric phenomena. The AIRS Infrared Sounder Experiment flies onboard NASA's Aqua spacecraft and is managed by NASA's Jet Propulsion Laboratory, Pasadena, Calif., under contract to NASA. JPL is a division of the California Institute of Technology in Pasadena.

Visual cortex activation in kinesthetic guidance of reaching.

PubMed

Darling, W G; Seitz, R J; Peltier, S; Tellmann, L; Butler, A J

2007-06-01

The purpose of this research was to determine the cortical circuit involved in encoding and controlling kinesthetically guided reaching movements. We used (15)O-butanol positron emission tomography in ten blindfolded able-bodied volunteers in a factorial experiment in which arm (left/right) used to encode target location and to reach back to the remembered location and hemispace of target location (left/right side of midsagittal plane) varied systematically. During encoding of a target the experimenter guided the hand to touch the index fingertip to an external target and then returned the hand to the start location. After a short delay the subject voluntarily moved the same hand back to the remembered target location. SPM99 analysis of the PET data contrasting left versus right hand reaching showed increased (P < 0.05, corrected) neural activity in the sensorimotor cortex, premotor cortex and posterior parietal lobule (PPL) contralateral to the moving hand. Additional neural activation was observed in prefrontal cortex and visual association areas of occipital and parietal lobes contralateral and ipsilateral to the reaching hand. There was no statistically significant effect of target location in left versus right hemispace nor was there an interaction of hand and hemispace effects. Structural equation modeling showed that parietal lobe visual association areas contributed to kinesthetic processing by both hands but occipital lobe visual areas contributed only during dominant hand kinesthetic processing. This visual processing may also involve visualization of kinesthetically guided target location and use of the same network employed to guide reaches to visual targets when reaching to kinesthetic targets. The present work clearly demonstrates a network for kinesthetic processing that includes higher visual processing areas in the PPL for both upper limbs and processing in occipital lobe visual areas for the dominant limb.

Characterizing hand-piled fuels

Treesearch

Clinton S. Wright; Paige C. Eagle; Cameron S. Balog

2010-01-01

Land managers throughout the West pile and burn surface fuels to mitigate fire hazard in dry forests. Whereas piling was historically conducted with heavy machinery following commercial harvesting operations, land managers are increasingly prescribing the use of hand piling and burning to treat surface fuels created by thinning and brush cutting. An estimate of the...

Hand-mouth transfer and potential for exposure to E. coli and F+ coliphage in beach sand, Chicago, Illinois

USGS Publications Warehouse

Whitman, R.L.; Przybyla-Kelly, K.; Shively, D.A.; Nevers, M.B.; Byappanahalli, M.N.

2009-01-01

Beach sand contains fecal indicator bacteria, often in densities greatly exceeding the adjacent swimming waters. We examined the transferability of Escherichia coli and F+ coliphage (MS2) from beach sand to hands in order to estimate the potential subsequent health risk. Sand with high initial E. coli concentrations was collected from a Chicago beach. Individuals manipulated the sand for 60 seconds, and rinse water was analysed for E. coli and coliphage. E. coli densities transferred were correlated with density in sand rather than surface area of an individual's hand, and the amount of coliphage transferred from seeded sand was different among individuals. In sequential rinsing, percentage reduction was 92% for E. coli and 98% for coliphage. Using dose-response estimates developed for swimming water, it was determined that the number of individuals per thousand that would develop gastrointestinal symptoms would be 11 if all E. coli on the fingertip were ingested or 33 if all E. coli on the hand were ingested. These results suggest that beach sand may be an important medium for microbial exposure; bacteria transfer is related to initial concentration in the sand; and rinsing may be effective in limiting oral exposure to sand-borne microbes of human concern.

A new 4-dimensional imaging system for jaw tracking.

PubMed

Lauren, Mark

2014-01-01

A non-invasive 4D imaging system that produces high resolution time-based 3D surface data has been developed to capture jaw motion. Fluorescent microspheres are brushed onto both tooth and soft-tissue areas of the upper and lower arches to be imaged. An extraoral hand-held imaging device, operated about 12 cm from the mouth, captures a time-based set of perspective image triplets of the patch areas. Each triplet, containing both upper and lower arch data, is converted to a high-resolution 3D point mesh using photogrammetry, providing the instantaneous relative jaw position. Eight 3D positions per second are captured. Using one of the 3D frames as a reference, a 4D model can be constructed to describe the incremental free body motion of the mandible. The surface data produced by this system can be registered to conventional 3D models of the dentition, allowing them to be animated. Applications include integration into prosthetic CAD and CBCT data.

Preparation of Silica Aerogel from TEOS

PubMed

Tamon; Kitamura; Okazaki

1998-01-15

Silica alcogels were synthesized by the sol-gel polymerization of tetraethylorthosilicate (TEOS). In the synthesis, HCl and NH3 were used as hydrolysis and condensation catalysts. The gelation time became short and the visible light transmittance increased with increasing the amount of HCl or lengthening the hydrolysis time. The alcogels were dried under supercritical conditions with carbon dioxide, and silica aerogels were obtained. As a result of characterization by visible light transmission and N2 adsorption, the aerogels are mesoporous materials with high surface areas. The experimental results suggest that the aerogel properties are not influenced by the drying conditions such as extraction temperature, extraction time, depressurizing temperature, and depressurizing rate. On the other hand, the properties are changed under the conditions of sol-gel polymerization. In the preparation of highly transparent aerogels with high surface areas and large pore volumes, it is necessary to synthesize highly transparent alcogels. It is found that the visible light transmittance of alcogels is an index for preparing aerogels from TEOS. Copyright 1998 Academic Press. Copyright 1998Academic Press

Arsenic transformation and adsorption by iron hydroxide/manganese dioxide doped straw activated carbon

NASA Astrophysics Data System (ADS)

Xiong, Ying; Tong, Qiang; Shan, Weijun; Xing, Zhiqiang; Wang, Yuejiao; Wen, Siqi; Lou, Zhenning

2017-09-01

Iron hydroxide/manganese dioxide doped straw activated carbon was synthesized for As(III) adsorption. The Fe-Mn-SAc adsorbent has two advantages, on the one hand, the straw active carbon has a large surface area (1360.99 m2 g-1) for FeOOH and MnO2 deposition, on the other hand, the manganese dioxide has oxidative property as a redox potential of (MnO2 + H+)/Mn2+, which could convert As(III) into As(V). Combined with the arsenic species after reacting with Fe-Mn-SAc, the As(III) transformation and adsorption mechanism was discussed. H2AsO4-oxidized from As(III) reacts with the Fe-Mn-SAc by electrostatic interaction, and unoxidized As(III) as H3AsO3 reacts with SAc and/or iron oxide surface by chelation effect. The adsorption was well-described by Langmuir isotherms model, and the adsorption capacity of As(III) was 75.82 mg g-1 at pH 3. Therefore, considering the straw as waste biomass material, the biosorbent (Fe-Mn-SAc) is promising to be exploited for applications in the treatment of industrial wastewaters containing a certain ratio of arsenic and germanium.

Age determination of mallards

USGS Publications Warehouse

Krapu, G.L.; Johnson, D.H.; Dane, C.W.

1979-01-01

A technique for distinguishing adult from yearling wild mallards (Anas platyrhynchos), from late winter through the nesting season, was developed by applying discriminant analysis procedures to selected wing feather characters of 126 yearlings and 76 adults (2-year-olds) hand-reared from wild eggs during 1974, 1975, and 1977. Average values for feather characters generally increased as the birds advanced from yearlings to adults. Black-white surface area of greater secondary covert 2 was the single most reliable aging character identified during the study. The error rate was lowest in females (3%) when discriminant functions were used with measurements of primary 1 weight and black-white area of greater secondary covert 2 and in males (9%) when the functions were used with black-white area of greater secondary coverts 1, 2, and 3. Methodology precludes aging of birds in the field during capture operations.

Langmuir probe measurements aboard the International Space Station

NASA Astrophysics Data System (ADS)

Kirov, B.; Asenovski, S.; Bachvarov, D.; Boneva, A.; Grushin, V.; Georgieva, K.; Klimov, S. I.

2016-12-01

In the current work we describe the Langmuir Probe (LP) and its operation on board the International Space Station. This instrument is a part of the scientific complex "Ostonovka". The main goal of the complex is to establish, on one hand how such big body as the International Space Station affects the ambient plasma and on the other how Space Weather factors influence the Station. The LP was designed and developed at BAS-SRTI. With this instrument we measure the thermal plasma parameters-electron temperature Te, electron and ion concentration, respectively Ne and Ni, and also the potential at the Station's surface. The instrument is positioned at around 1.5 meters from the surface of the Station, at the Russian module "Zvezda", located at the farthermost point of the Space Station, considering the velocity vector. The Multi- Purpose Laboratory (MLM) module is providing additional shielding for our instrument, from the oncoming plasma flow (with respect to the velocity vector). Measurements show that in this area, the plasma concentration is two orders of magnitude lower, in comparison with the unperturbed areas. The surface potential fluctuates between-3 and-25 volts with respect to the ambient plasma. Fast upsurges in the surface potential are detected when passing over the twilight zone and the Equatorial anomaly.

The `Chocolate Experiment' - A Demonstration of Radiation Absorption by Different Colored Surfaces

NASA Astrophysics Data System (ADS)

Fung, Dennis

2015-12-01

In the typical "cookbook" experiment comparing the radiation absorption rates of different colored surfaces, students' hands are commonly used as a measurement instrument to demonstrate that dull black and silvery surfaces are good and poor absorbers of radiation, respectively. However, college students are often skeptical about using their bare hands in this experiment because they learned in early science lessons that skin is not a reliable detector of heat transfer. Moreover, when the experiment is conducted in a school laboratory, it is often difficult for students to perceive the slight differences in heat transfer on the dull black and silvery aluminum leaves attached to their hands. Rather than replacing students' bare hands with such sophisticated apparatus as a data logger and temperature probe, I suggest using a simple (and delicious!) low-cost instrument, i.e., chocolate, which simply melts when it receives radiation.

Differences in Cortical Representation and Structural Connectivity of Hands and Feet between Professional Handball Players and Ballet Dancers

PubMed Central

Meier, Jessica; Topka, Marlene Sofie; Hänggi, Jürgen

2016-01-01

It is known that intensive training and expertise are associated with functional and structural neuroadaptations. Most studies, however, compared experts with nonexperts; hence it is, specifically for sports, unclear whether the neuroplastic adaptations reported are sport-specific or sport-general. Here we aimed at investigating sport-specific adaptations in professional handball players and ballet dancers by focusing on the primary motor and somatosensory grey matter (GM) representation of hands and feet using voxel-based morphometry as well as on fractional anisotropy (FA) of the corticospinal tract by means of diffusion tensor imaging-based fibre tractography. As predicted, GM volume was increased in hand areas of handball players, whereas ballet dancers showed increased GM volume in foot areas. Compared to handball players, ballet dancers showed decreased FA in both fibres connecting the foot and hand areas, but they showed lower FA in fibres connecting the foot compared to their hand areas, whereas handball players showed lower FA in fibres connecting the hand compared to their foot areas. Our results suggest that structural adaptations are sport-specific and are manifested in brain regions associated with the neural processing of sport-specific skills. We believe this enriches the plasticity research in general and extends our knowledge of sport expertise in particular. PMID:27247805

Differences in Cortical Representation and Structural Connectivity of Hands and Feet between Professional Handball Players and Ballet Dancers.

PubMed

Meier, Jessica; Topka, Marlene Sofie; Hänggi, Jürgen

2016-01-01

It is known that intensive training and expertise are associated with functional and structural neuroadaptations. Most studies, however, compared experts with nonexperts; hence it is, specifically for sports, unclear whether the neuroplastic adaptations reported are sport-specific or sport-general. Here we aimed at investigating sport-specific adaptations in professional handball players and ballet dancers by focusing on the primary motor and somatosensory grey matter (GM) representation of hands and feet using voxel-based morphometry as well as on fractional anisotropy (FA) of the corticospinal tract by means of diffusion tensor imaging-based fibre tractography. As predicted, GM volume was increased in hand areas of handball players, whereas ballet dancers showed increased GM volume in foot areas. Compared to handball players, ballet dancers showed decreased FA in both fibres connecting the foot and hand areas, but they showed lower FA in fibres connecting the foot compared to their hand areas, whereas handball players showed lower FA in fibres connecting the hand compared to their foot areas. Our results suggest that structural adaptations are sport-specific and are manifested in brain regions associated with the neural processing of sport-specific skills. We believe this enriches the plasticity research in general and extends our knowledge of sport expertise in particular.

Johnson Space Center: Workmanship Training

NASA Technical Reports Server (NTRS)

Patterson, Ashley; Sikes, Larry; Corbin, Cheryl; Rucka, Becky

2015-01-01

Special processes require special skills, knowledge and experienced application. For over 15 years, the NASA Johnson Space Center's Receiving, Inspection and Test Facility (RITF) has provided Agency-wide NASA Workmanship Standards compliance training, issuing more than 500 to 800 training completion certificates annually. It is critical that technicians and inspectors are trained and that they maintain their proficiency to implement the applicable standards and specifications. Training services include "hands-on" training to engineers, technicians, and inspectors in the areas of electrostatic discharge (ESD), soldering, surface mount technology (SMT), crimping, conformal coating, and fiber-optic terminations.

Quantitative Estimation of Land Surface Characteristic Parameters and Actual Evapotranspiration in the Nagqu River Basin over the Tibetan Plateau

NASA Astrophysics Data System (ADS)

Zhong, L.; Ma, Y.; Ma, W.; Zou, M.; Hu, Y.

2016-12-01

Actual evapotranspiration (ETa) is an important component of the water cycle in the Tibetan Plateau. It is controlled by many hydrological and meteorological factors. Therefore, it is of great significance to estimate ETa accurately and continuously. It is also drawing much attention of scientific community to understand land surface parameters and land-atmosphere water exchange processes in small watershed-scale areas. Based on in-situ meteorological data in the Nagqu river basin and surrounding regions, the main meteorological factors affecting the evaporation process were quantitatively analyzed and the point-scale ETa estimation models in the study area were successfully built. On the other hand, multi-source satellite data (such as SPOT, MODIS, FY-2C) were used to derive the surface characteristics in the river basin. A time series processing technique was applied to remove cloud cover and reconstruct data series. Then improved land surface albedo, improved downward shortwave radiation flux and reconstructed normalized difference vegetation index (NDVI) were coupled into the topographical enhanced surface energy balance system to estimate ETa. The model-estimated results were compared with those ETa values determined by combinatory method. The results indicated that the model-estimated ETa agreed well with in-situ measurements with correlation coefficient, mean bias error and root mean square error of 0.836, 0.087 and 0.140 mm/h respectively.

30 CFR 56.7053 - Moving hand-held drills.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Moving hand-held drills. 56.7053 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7053 Moving hand-held drills. Before hand-held drills are moved from one...

30 CFR 56.7053 - Moving hand-held drills.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Moving hand-held drills. 56.7053 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7053 Moving hand-held drills. Before hand-held drills are moved from one...

30 CFR 56.7053 - Moving hand-held drills.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Moving hand-held drills. 56.7053 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7053 Moving hand-held drills. Before hand-held drills are moved from one...

30 CFR 56.7053 - Moving hand-held drills.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Moving hand-held drills. 56.7053 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7053 Moving hand-held drills. Before hand-held drills are moved from one...

30 CFR 56.7053 - Moving hand-held drills.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Moving hand-held drills. 56.7053 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Drilling and Rotary Jet Piercing Drilling § 56.7053 Moving hand-held drills. Before hand-held drills are moved from one...

Effects of knowledge and internal locus of control in groups of health care workers judging likelihood of pathogen transfer.

PubMed

McLaughlin, Anne Collins; Walsh, Fran; Bryant, Michelle

2013-08-01

A study was conducted to measure the effects of attitudes and beliefs on the risk judgments of health care workers. Lack of hand hygiene compliance is a worldwide issue in health care, contributing to infections, fatalities, and increased health care costs. Human factors methods are a promising solution to the problem of compliance, although thus far, the concentration has been on process and engineering methods, such as the design of no-touch sinks. Factors internal to the health care worker, such as their attitudes and beliefs about hand hygiene, have received less attention. For this study, three groups of health care workers completed measures of attitudes, control beliefs, and hand hygiene knowledge. They then provided risk judgments of touching various surfaces via a factorial survey. Attitudes, knowledge, control beliefs, and surface type all predicted the risk judgments of the sample of health care workers, with differences between professional groups. Health care workers perceive less risk when touching surfaces,which may explain historically low rates of hand hygiene compliance after surface contact. Although more research is needed to directly connect risk judgments to failures of hand hygiene, the current results can inform interventions targeting the internal attitudes and beliefs of health care workers.

Oregano essential oil as an antimicrobial additive to detergent for hand washing and food contact surface cleaning.

PubMed

Rhoades, J; Gialagkolidou, K; Gogou, M; Mavridou, O; Blatsiotis, N; Ritzoulis, C; Likotrafiti, E

2013-10-01

To investigate the potential use of oregano essential oil as an antimicrobial agent in liquid soap for hand washing and for food contact surface cleaning. Oregano essential oil (O.E.O.) was emulsified in liquid detergent solution. This was challenge tested against a commercial antimicrobial soap in hand washing trials using natural flora. Soap with O.E.O. was as effective as the commercial antimicrobial soap at reducing aerobic plate count on the hands and more effective than plain soap with no additives. Cloths wetted with soap with O.E.O. were used to clean three different surfaces contaminated with four bacterial pathogens. For three of the four pathogens, the addition of 0·5% v/v O.E.O. to the soap solution enhanced cleaning performance and also reduced bacterial survival on the cloth after cleaning. Oregano essential oil (0·5%) is effective as an antimicrobial additive to detergent solutions for hand washing and surface cleaning. This preliminary study has shown that oregano essential oil is a potential alternative to antimicrobials used in various detergents, such as chloroxylenol and triclosan, which can have adverse environmental and health effects. Further development could lead to a commercial product. © 2013 The Society for Applied Microbiology.

Using airborne thermal infrared imagery and helicopter EM conductivity to locate mine pools and discharges in the Kettle Creek watershed, north-central Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Love, E.; Hammack, R.W.; Harbert, W.P.

2005-11-01

The Kettle Creek watershed contains 50–100-year-old surface and underground coal mines that are a continuing source of acid mine drainage (AMD). To characterize the mining-altered hydrology of this watershed, an airborne reconnaissance was conducted in 2002 using airborne thermal infrared imagery (TIR) and helicopter-mounted electromagnetic (HEM) surveys. TIR uses the temperature differential between surface water and groundwater to locate areas where groundwater emerges at the surface. TIR anomalies located in the survey included seeps and springs, as well as mine discharges. In a follow-up ground investigation, hand-held GPS units were used to locate 103 of the TIR anomalies. Of themore » sites investigated, 26 correlated with known mine discharges, whereas 27 were previously unknown. Seven known mine discharges previously obscured from TIR imagery were documented. HEM surveys were used to delineate the groundwater table and also to locate mine pools, mine discharges, and groundwater recharge zones. These surveys located 12 source regions and flow paths for acidic, metal-containing (conductive) mine drainage; areas containing acid-generating mine spoil; and areas of groundwater recharge and discharge, as well as identifying potential mine discharges previously obscured from TIR imagery by nondeciduous vegetation. Follow-up ground-based electromagnetic surveys verified the results of the HEM survey. Our study suggests that airborne reconnaissance can make the remediation of large watersheds more efficient by focusing expensive ground surveys on small target areas.« less

Using airborne thermal infrared imagery and helicopter EM conductivity to locate mine pools and discharges in the Kettle Creek watershed, north-central Pennsylvania

DOE Office of Scientific and Technical Information (OSTI.GOV)

Love, E.; Hammack, R.; Harbert, W.

2005-12-01

The Kettle Creek watershed contains 50-100-year-old surface and underground coal mines that are a continuing source of acid mine drainage (AMD). To characterize the mining-altered hydrology of this watershed, an airborne reconnaissance was conducted in 2002 using airborne thermal infrared imagery (TIR) and helicopter-mounted electromagnetic (HEM) surveys. TIR uses the temperature differential between surface water and groundwater to locate areas where groundwater emerges at the surface. TIR anomalies located in the survey included seeps and springs, as well as mine discharges. In a follow-up ground investigation, hand-held GPS units were used to locate 103 of the TIR anomalies. Of themore » sites investigated, 26 correlated with known mine discharges, whereas 27 were previously unknown. Seven known mine discharges previously obscured from TIR imagery were documented. HEM surveys were used to delineate the groundwater table and also to locate mine pools, mine discharges, and groundwater recharge zones. These surveys located 12 source regions and flow paths for acidic, metal-containing (conductive) mine drainage; areas containing acid-generating mine spoil; and areas of groundwater recharge and discharge, as well as identifying potential mine discharges previously obscured from TIR imagery by nondeciduous vegetation. Follow-up ground-based electromagnetic surveys verified the results of the HEM survey. Our study suggests that airborne reconnaissance can make the remediation of large watersheds more efficient by focusing expensive ground surveys on small target areas.« less

Epitaxial strain relaxation by provoking edge dislocation dipoles

NASA Astrophysics Data System (ADS)

Soufi, A.; El-Hami, K.

2018-02-01

Thin solid films have been used in various devices and engineering systems such as rapid development of highly integrated electronic circuits, the use of surface coatings to protect structural materials in high temperature environments, and thin films are integral parts of many micro-electro-mechanical systems designed to serve as sensors, actuators. Among techniques of ultra-thin films deposition, the heteroepitaxial method becomes the most useful at nanoscale level to obtain performed materials in various applications areas. On the other hand, stresses that appeared during the elaboration of thin films could rise deformations and fractures in materials. The key solution to solve this problem at the nanoscale level is the nucleation of interface dislocations from free surfaces. By provoking edge dislocation dipoles we obtained a strain relaxation in thin films. Moreover, the dynamic of nucleation in edge dislocations from free lateral surfaces was also studied.

Beaming Circularly Polarized Photons from Quantum Dots Coupled with Plasmonic Spiral Antenna (Postprint)

DTIC Science & Technology

2014-01-01

SYMBOLS Acronym Definition SPP Surface Plasmon Polaritons RHC Right-Hand Circular LHC Left-Hand Circular FIB Focused Ion Beam RHS Right-Handed Spiral CCD Charge-Coupled Detector FWHM Full Width at Half Maximum

A Helping Hand.

ERIC Educational Resources Information Center

Renner, Jason M.

2000-01-01

Discusses how designing a hand washing-friendly environment can help to reduce the spread of germs in school restrooms. Use of electronic faucets, surface risk management, traffic flow, and user- friendly hand washing systems that are convenient and maximally hygienic are examined. (GR)

KSC-07pd0158

NASA Image and Video Library

2007-01-23

KENNEDY SPACE CENTER, FLA. -- The right-hand orbital maneuvering system pod is being delivered to Orbiter Processing Facility bay 2 for installation on the orbiter Endeavour. The orbital maneuvering system/reaction control system left- and right-hand pods are attached to the upper aft fuselage left and right sides. Each pod is fabricated primarily of graphite epoxy composite and aluminum. Each pod is 21.8 feet long and 11.37 feet wide at its aft end and 8.41 feet wide at its forward end, with a surface area of approximately 435 square feet. The orbiter is being prepared for its first launch in just over four years. The vehicle has undergone an extensive modification period, including the addition of all of the return-to-flight safety upgrades added to both Discovery and Atlantis. Endeavour is targeted for launch of mission STS-118 on June 28. Photo credit: NASA/Kim Shiflett

KSC-07pd0159

NASA Image and Video Library

2007-01-23

KENNEDY SPACE CENTER, FLA. -- The right-hand orbital maneuvering system pod is driven past the Vehicle Assembly Building on its way to Orbiter Processing Facility bay 2 for installation on the orbiter Endeavour. The orbital maneuvering system/reaction control system left- and right-hand pods are attached to the upper aft fuselage left and right sides. Each pod is fabricated primarily of graphite epoxy composite and aluminum. Each pod is 21.8 feet long and 11.37 feet wide at its aft end and 8.41 feet wide at its forward end, with a surface area of approximately 435 square feet. The orbiter is being prepared for its first launch in just over four years. The vehicle has undergone an extensive modification period, including the addition of all of the return-to-flight safety upgrades added to both Discovery and Atlantis. Endeavour is targeted for launch of mission STS-118 on June 28. Photo credit: NASA/Kim Shiflett

Further Development and Application of GEOFRAC-FLOW to a Geothermal Reservoir

DOE Office of Scientific and Technical Information (OSTI.GOV)

Einstein, Herbert; Vecchiarelli, Alessandra

2014-05-01

GEOFRAC is a three-dimensional, geology-based, geometric-mechanical, hierarchical, stochastic model of natural rock fracture systems. The main characteristics of GEOFRAC are its use of statistical input representing fracture patterns in the field in form of the fracture intensity P32 (fracture area per volume) and the best estimate fracture size E(A). This information can be obtained from boreholes or scanlines on the surface, on the one hand, and from window sampling of fracture traces on the other hand. In the context of this project, “Recovery Act - Decision Aids for Geothermal Systems”, GEOFRAC was further developed into GEOFRAC-FLOW as has been reportedmore » in the reports, “Decision Aids for Geothermal Systems - Fracture Pattern Modelling” and “Decision Aids for Geothermal Systems - Fracture Flow Modeling”. GEOFRAC-FLOW allows one to determine preferred, interconnected fracture paths and the flow through them.« less

Removal of bio-aerosols by water flow on surfaces in health-care settings

NASA Astrophysics Data System (ADS)

Yu, Han; Li, Yuguo

2016-11-01

Hand hygiene is one of the most important and efficient measures to prevent infections, however the compliance with hand hygiene remains poor especially for health-care workers. To improve this situation, the mechanisms of hand cleansing need to be explored and a detailed study on the adhesion interactions for bio-aerosols on hand surfaces and the process during particles removal by flow is significant for more efficient methods to decrease infections. The first part of presentation will focus on modelling adhesion interactions between particles, like bacteria and virus, and hand surfaces with roughness in water environment. The model presented is based on the DLVO and its extended theories. The removal process comes next, which will put forward a new model to describe the removal of particles by water flow. In this model, molecular dynamics is combined with particle motion and the results by the model will be compared with experiment results and existed models (RnR, Rock & Roll). Finally, possible improvement of the study and future design of experiments will be discussed.

Modeling environmental contamination in hospital single- and four-bed rooms.

PubMed

King, M-F; Noakes, C J; Sleigh, P A

2015-12-01

Aerial dispersion of pathogens is recognized as a potential transmission route for hospital acquired infections; however, little is known about the link between healthcare worker (HCW) contacts' with contaminated surfaces, the transmission of infections and hospital room design. We combine computational fluid dynamics (CFD) simulations of bioaerosol deposition with a validated probabilistic HCW-surface contact model to estimate the relative quantity of pathogens accrued on hands during six types of care procedures in two room types. Results demonstrate that care type is most influential (P < 0.001), followed by the number of surface contacts (P < 0.001) and the distribution of surface pathogens (P = 0.05). Highest hand contamination was predicted during Personal care despite the highest levels of hand hygiene. Ventilation rates of 6 ac/h vs. 4 ac/h showed only minor reductions in predicted hand colonization. Pathogens accrued on hands decreased monotonically after patient care in single rooms due to the physical barrier of bioaerosol transmission between rooms and subsequent hand sanitation. Conversely, contamination was predicted to increase during contact with patients in four-bed rooms due to spatial spread of pathogens. Location of the infectious patient with respect to ventilation played a key role in determining pathogen loadings (P = 0.05). We present the first quantitative model predicting the surface contacts by HCW and the subsequent accretion of pathogenic material as they perform standard patient care. This model indicates that single rooms may significantly reduce the risk of cross-contamination due to indirect infection transmission. Not all care types pose the same risks to patients, and housekeeping performed by HCWs may be an important contribution in the transmission of pathogens between patients. Ventilation rates and positioning of infectious patients within four-bed rooms can mitigate the accretion of pathogens, whereby reducing the risk of missed hand hygiene opportunities. The model provides a tool to quantitatively evaluate the influence of hospital room design on infection risk. © 2015 The Authors. Indoor Air Published by John Wiley & Sons Ltd.

Support for Conference Entitled The Fifth PHANTOM Users Group Workshop

DTIC Science & Technology

2001-02-01

amplified by using extended A collection of functional test environments were assembled hand tools like a hammer, pipe wrench, or tennis racket. The to...view their hand, were seated at a desk, Surfaces were presented at a range of orientations, resting their right elbow on its surface, and used a in

Apollo 13 Astronaut James Lovel during lunar surface simulation training

NASA Image and Video Library

1970-01-16

S70-28229 (16 Jan. 1970) --- Astronaut James A. Lovell Jr., commander of the Apollo 13 lunar landing mission, participates in lunar surface simulation training at the Manned Spacecraft Center. Lovell is attached to a Six Degrees of Freedom Simulator. He is carrying an Apollo Lunar Hand Tools carrier in his right hand.

Assessment of materials commonly utilized in health care: implications for bacterial survival and transmission.

PubMed

Lankford, Mary G; Collins, Susan; Youngberg, Larry; Rooney, Denise M; Warren, John R; Noskin, Gary A

2006-06-01

Contaminated environmental surfaces, equipment, and health care workers' hands have been linked to outbreaks of infection or colonization because of vancomycin-resistant enterococci (VRE) and Pseudomonas aeruginosa (PSAE). Upholstery, walls, and flooring may enhance bacterial survival, providing infectious reservoirs. Investigate recovery of VRE and PSAE, determine efficacy of disinfection, and evaluate VRE transmission from surfaces. Upholstery, flooring, and wall coverings were inoculated with VRE and PSAE and assessed for recovery at 24 hours, 72 hours, and 7 days. Inoculated surfaces were cleaned utilizing manufacturers' recommendations of natural, commercial, or hospital-approved products and methods, and samples were obtained. To assess potential for transmission, volunteers touched VRE-inoculated surfaces and imprinted palms onto contact-impression plates. Twenty-four hours following inoculation, all surfaces had recovery of VRE; 13 (92.9%) of 14 surfaces had persistent PSAE. After cleaning, VRE was recovered from 7 (50%) surfaces, PSAE from 5 (35.7%) surfaces. After inoculation followed by palmar contact, VRE was recovered from all surfaces touched. Bacteria commonly encountered in hospitals are capable of prolonged survival and may promote cross transmission. Selection of surfaces for health care environments should include product application and complexity of manufacturers' recommendations for disinfection. Recovery of organisms on surfaces and hands emphasizes importance of hand hygiene compliance prior to patient contact.

Microsphere integrated microfluidic disk: synergy of two techniques for rapid and ultrasensitive dengue detection.

PubMed

Hosseini, Samira; Aeinehvand, Mohammad M; Uddin, Shah M; Benzina, Abderazak; Rothan, Hussin A; Yusof, Rohana; Koole, Leo H; Madou, Marc J; Djordjevic, Ivan; Ibrahim, Fatimah

2015-11-09

The application of microfluidic devices in diagnostic systems is well-established in contemporary research. Large specific surface area of microspheres, on the other hand, has secured an important position for their use in bioanalytical assays. Herein, we report a combination of microspheres and microfluidic disk in a unique hybrid platform for highly sensitive and selective detection of dengue virus. Surface engineered polymethacrylate microspheres with carefully designed functional groups facilitate biorecognition in a multitude manner. In order to maximize the utility of the microspheres' specific surface area in biomolecular interaction, the microfluidic disk was equipped with a micromixing system. The mixing mechanism (microballoon mixing) enhances the number of molecular encounters between spheres and target analyte by accessing the entire sample volume more effectively, which subsequently results in signal amplification. Significant reduction of incubation time along with considerable lower detection limits were the prime motivations for the integration of microspheres inside the microfluidic disk. Lengthy incubations of routine analytical assays were reduced from 2 hours to 5 minutes while developed system successfully detected a few units of dengue virus. Obtained results make this hybrid microsphere-microfluidic approach to dengue detection a promising avenue for early detection of this fatal illness.

Contact infection of infectious disease onboard a cruise ship.

PubMed

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y Y

2016-12-08

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces.

Contact infection of infectious disease onboard a cruise ship

PubMed Central

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y. Y.

2016-01-01

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces. PMID:27929141

Chemical activation of bituminous coal for hampering oligomerization of organic contaminants.

PubMed

Yan, Liang; Sorial, George A

2011-12-15

Activated carbons prepared by KOH activation of bituminous coal were studied for hampering oligomerization of phenolic compounds on its surface. A total of 24 activated carbons with different microporosity and BET surface area were created. The effect of the different variables of the activation process (KOH/bituminous coal ratio, heating temperature, activation time, and flow rate of nitrogen gas) on critical carbon parameters was analyzed. The impact of activated carbon on oligomerization was examined by conducting isotherm experiments at a neutral pH on Carbon(exp) produced with optimal characteristics and granular activated carbon (GAC) F400 for phenol, 2-methylphenol and 2-ethylphenol. These isotherms were collected under anoxic (absence of molecular oxygen) and oxic (presence of molecular oxygen) conditions. The single solute adsorption of phenol, 2-methylphenol and 2-ethylphenol on Carbon(exp) showed no obvious differences between oxic and anoxic environment, which indicated that the Carbon(exp) sample is very effective in hampering the oligomerization of phenolic compounds under oxic conditions. On the other hand, F400, which have lower micropore percentage and BET surface area, significant increases in the adsorptive capacity had been observed when molecular oxygen was present. Copyright © 2011 Elsevier B.V. All rights reserved.

Contact infection of infectious disease onboard a cruise ship

NASA Astrophysics Data System (ADS)

Zhang, Nan; Miao, Ruosong; Huang, Hong; Chan, Emily Y. Y.

2016-12-01

Cruise tourism has become more popular. Long-term personal contact, complex population flows, a lack of medical care facilities, and defective infrastructure aboard most cruise ships is likely to result in the ship becoming an incubator for infectious diseases. In this paper, we use a cruise ship as a research scenario. Taking into consideration personal behavior, the nature and transfer route of the virus across different surfaces, virus reproduction, and disinfection, we studied contact infection of infectious disease on a cruise ship. Using gastroenteritis caused by the norovirus as an example, we analyzed the characteristics of infectious disease propagation based on simulation results under different conditions. We found hand washing are the most important factors affecting virus propagation and passenger infection. It also decides either the total number of virus microorganisms or the virus distribution in different functional areas. The transfer rate between different surfaces is a key factor influencing the concentricity of the virus. A high transfer rate leads to high concentricity. In addition, the risk of getting infected is effectively reduced when the disinfection frequency is above a certain threshold. The efficiency of disinfection of functional areas is determined by total virus number and total contact times of surfaces.

Wearable light management system for light stimulated healing of large area chronic wounds (Conference Presentation)

NASA Astrophysics Data System (ADS)

Kallweit, David; Mayer, Jan; Fricke, Sören; Schnieper, Marc; Ferrini, Rolando

2016-03-01

Chronic wounds represent a significant burden to patients, health care professionals, and health care systems, affecting over 40 million patients and creating costs of approximately 40 billion € annually. We will present a medical device for photo-stimulated wound care based on a wearable large area flexible and disposable light management system consisting of a waveguide with incorporated micro- and nanometer scale optical structures for efficient light in-coupling, waveguiding and homogeneous illumination of large area wounds. The working principle of this innovative device is based on the therapeutic effects of visible light to facilitate the self-healing process of chronic wounds. On the one hand, light exposure in the red (656nm) induces growth of keratinocytes and fibroblasts in deeper layers of the skin. On the other hand, blue light (453nm) is known to have antibacterial effects predominately at the surface layers of the skin. In order to be compliant with medical requirements the system will consist of two elements: a disposable wound dressing with embedded flexible optical waveguides for the light management and illumination of the wound area, and a non-disposable compact module containing the light sources, a controller, a rechargeable battery, and a data transmission unit. In particular, we will report on the developed light management system. Finally, as a proof-of-concept, a demonstrator will be presented and its performances will be reported to demonstrate the potential of this innovative device.

Three frequency false-color image of Oberpfaffenhofen supersite in Germany

NASA Technical Reports Server (NTRS)

1994-01-01

This is a three-frequency, false color image of the Oberpfaffenhofen supersite, an area just south-west of Munich in southern Germany. This image was acquired by the Spaceborne Imaging Radar-C and X-Band Synthetic Aperture Radar (SIR-C/X-SAR) aboard the Shuttle Endeavour, April 11, 1994. The image is centered at 48.09 degrees north, 11.29 degrees east. The dark area on the left is Lake Ammersee. The two smaller lakes are the Woerthsee and the Pilsensee. On the bottom is the tip of the Starnbergersee. The city of Munich is located just beyond the right of the image. The forested areas have a reddish tint (L-Band). THe green areas seen near both the Ammersee and the Pilsensee lakes indicate marshy areas. The agricultural fields in the upper right hand corner appear mostly in blue and green (X-band and C-band). The white areas are mostly urban areas, while the smooth surfaces of the lakes appear very dark. The Jet Propulsion Laboratory alternative photo number is P-43930.

An electrochemical impedance spectroscopy study of polymer electrolyte membrane fuel cells electrocatalyst single wall carbon nanohorns-supported.

PubMed

Brandão, Lúcia; Boaventura, Marta; Passeira, Carolina; Gattia, Daniele Mirabile; Marazzi, Renzo; Antisari, Marco Vittori; Mendes, Adélio

2011-10-01

Electrochemical impedance spectroscopy (EIS) was used to study the polymer electrolyte membrane fuel cells (PEMFC) performance when using single wall carbon nanohorns (SWNH) to support Pt nanoparticles. Additionally, as-prepared and oxidized SWNH Pt-supports were compared with conventional carbon black. Two different oxidizing treatments were considered: oxygen flow at 500 degrees C and reflux in an acid solution at 85 degrees C. Both oxidizing treatments increased SWNH surface area; oxygen treatment increased surface area 4 times while acid treatment increased 2.6 times. The increase in surface area should be related to the opening access to the inner tube of SWNH. Acid treatment of SWNH increased chemical fragility and decreased electrocatalyst load in comparison with as-prepared SWNH. On the other hand, the oxygen treated SWNH sample allowed to obtain the highest electrocatalyst load. The use of as-prepared and oxygen treated SWNH showed in both cases catalytic activities 60% higher than using conventional carbon black as electrocatalyst support in PEMFC. Moreover, EIS analysis indicated that the major improvement in performance is related to the cathode kinetics in the as-prepared SWNH sample, while concerning the oxidized SWNH sample, the improvements are related to the electrokinetics in both anode and cathode electrodes. These improvements should be related with differences in the hydrophobic character between SWNH and carbon black.

Erosion processes in molassic cliffs: the role of the rock surface temperature and atmospheric conditions

NASA Astrophysics Data System (ADS)

Carrea, Dario; Abellán, Antonio; Guerin, Antoine; Jaboyedoff, Michel; Voumard, Jérémie

2014-05-01

The morphology of the Swiss Plateau is modeled by numerous steep cliffs of Molasse. These cliffs are mainly composed of sub-horizontal alternated layers of sandstone, shale and conglomerates deposed in the Alps foreland basin during the Tertiary period. These Molasse cliffs are affected by erosion processes inducing numerous rockfall events. Thus, it is relevant to understand how different external factors influence Molasse erosion rates. In this study, we focus on analyzing temperature variation during a winter season. As pilot study area we selected a cliff which is formed by a sub-horizontal alternation of outcropping sandstone and shale. The westward facing test site (La Cornalle, Vaud, Switzerland), which is a lateral scarp of a slow moving landslide area, is currently affected by intense erosion. Regarding data acquisition, we monitored both in-situ rock and air temperatures at 15 minutes time-step since October 2013: (1) on the one hand we measured Ground Surface Temperature (GST) at near-surface (0.1 meter depth) using a GST mini-datalogger M-Log5W-Rock model; (2) On the other hand we monitored atmospheric conditions using a weather station (Davis Vantage pro2 plus) collecting numerous parameters (i.e. temperature, irradiation, rain, wind speed, etc.). Furthermore, the area was also seasonally monitored by Ground-Based (GB) LiDAR since 2010 and monthly monitored since September 2013. In order to understand how atmospheric conditions (such as freeze and thaw effect) influence the erosion of the cliff, we modeled the temperature diffusion through the rock mass. To this end, we applied heat diffusion and radiation equation using a 1D temperature profile, obtaining as a result both temperature variations at different depths together with the location of the 0°C isotherm. Our model was calibrated during a given training set using both in-situ rock temperatures and atmospheric conditions. We then carried out a comparison with the rockfall events derived from the 3D GB-LiDAR datasets in order to quantify the erosion rates and to correlate it with atmospheric conditions, aiming to analyze which parameters influence Molasse erosion process.

A review on the structural styles of deformation during Late Cretaceous and Paleocene tectonic phases in the southern North Sea area

NASA Astrophysics Data System (ADS)

Deckers, Jef; van der Voet, Eva

2018-04-01

The Mesozoic rifts in the southern North Sea area were affected by Late Cretaceous to Paleocene inversion. Two main inversion phases were traditionally identified in this interval: the Sub-Hercynian and the Laramide phases. The Sub-Hercynian phase started in the early Late Cretaceous, peaked during the Campanian and ended in the late Maastrichtian, while the Laramide phase started in the late Danian and ended in the Thanetian. The Late Cretaceous Sub-Hercynian phase was strong and occurred in several pulses. These pulses led to basin-scale uplift by large reverse movements along basin-bounding faults and resulted in large amounts of erosion (up to 2 km) of Mesozoic and older sediments. The middle Paleocene Laramide phase on the other hand resulted in mild, domal uplift of some Late Cretaceous inverted basins and subsidence (into depocenters) of others. The subsequent Cenozoic inversion phases displayed similar or lower amplitudes and wavelengths of vertical surface movements as the Laramide phase. The transition from the Sub-Hercynian to the Laramide phase in the southern North Sea area therefore coincides with the overall transition from fault-controlled inversion to broad domal vertical surface movements.

Mapping surface disturbance of energy-related infrastructure in southwest Wyoming--An assessment of methods

USGS Publications Warehouse

Germaine, Stephen S.; O'Donnell, Michael S.; Aldridge, Cameron L.; Baer, Lori; Fancher, Tammy; McBeth, Jamie; McDougal, Robert R.; Waltermire, Robert; Bowen, Zachary H.; Diffendorfer, James; Garman, Steven; Hanson, Leanne

2012-01-01

We evaluated how well three leading information-extraction software programs (eCognition, Feature Analyst, Feature Extraction) and manual hand digitization interpreted information from remotely sensed imagery of a visually complex gas field in Wyoming. Specifically, we compared how each mapped the area of and classified the disturbance features present on each of three remotely sensed images, including 30-meter-resolution Landsat, 10-meter-resolution SPOT (Satellite Pour l'Observation de la Terre), and 0.6-meter resolution pan-sharpened QuickBird scenes. Feature Extraction mapped the spatial area of disturbance features most accurately on the Landsat and QuickBird imagery, while hand digitization was most accurate on the SPOT imagery. Footprint non-overlap error was smallest on the Feature Analyst map of the Landsat imagery, the hand digitization map of the SPOT imagery, and the Feature Extraction map of the QuickBird imagery. When evaluating feature classification success against a set of ground-truthed control points, Feature Analyst, Feature Extraction, and hand digitization classified features with similar success on the QuickBird and SPOT imagery, while eCognition classified features poorly relative to the other methods. All maps derived from Landsat imagery classified disturbance features poorly. Using the hand digitized QuickBird data as a reference and making pixel-by-pixel comparisons, Feature Extraction classified features best overall on the QuickBird imagery, and Feature Analyst classified features best overall on the SPOT and Landsat imagery. Based on the entire suite of tasks we evaluated, Feature Extraction performed best overall on the Landsat and QuickBird imagery, while hand digitization performed best overall on the SPOT imagery, and eCognition performed worst overall on all three images. Error rates for both area measurements and feature classification were prohibitively high on Landsat imagery, while QuickBird was time and cost prohibitive for mapping large spatial extents. The SPOT imagery produced map products that were far more accurate than Landsat and did so at a far lower cost than QuickBird imagery. Consideration of degree of map accuracy required, costs associated with image acquisition, software, operator and computation time, and tradeoffs in the form of spatial extent versus resolution should all be considered when evaluating which combination of imagery and information-extraction method might best serve any given land use mapping project. When resources permit, attaining imagery that supports the highest classification and measurement accuracy possible is recommended.

Vapor-Phase Nanopatterning of Aminosilanes with Electron Beam Lithography: Understanding and Minimizing Background Functionalization.

PubMed

Fetterly, Christopher R; Olsen, Brian C; Luber, Erik J; Buriak, Jillian M

2018-04-24

Electron beam lithography (EBL) is a highly precise, serial method for patterning surfaces. Positive tone EBL resists enable patterned exposure of the underlying surface, which can be subsequently functionalized for the application of interest. In the case of widely used native oxide-capped silicon surfaces, coupling an activated silane with electron beam lithography would enable nanoscale chemical patterning of the exposed regions. Aminoalkoxysilanes are extremely useful due to their reactive amino functionality but have seen little attention for nanopatterning silicon surfaces with an EBL resist due to background contamination. In this work, we investigated three commercial positive tone EBL resists, PMMA (950k and 495k) and ZEP520A (57k), as templates for vapor-phase patterning of two commonly used aminoalkoxysilanes, 3-aminopropyltrimethoxysilane (APTMS) and 3-aminopropyldiisopropylethoxysilane (APDIPES). The PMMA resists were susceptible to significant background reaction within unpatterned areas, a problem that was particularly acute with APTMS. On the other hand, with both APTMS and APDIPES exposure, unpatterned regions of silicon covered by the ZEP520A resist emerged pristine, as shown both with SEM images of the surfaces of the underlying silicon and through the lack of electrostatically driven binding of negatively charged gold nanoparticles. The ZEP520A resist allowed for the highly selective deposition of these alkoxyaminosilanes in the exposed areas, leaving the unpatterned areas clean, a claim also supported by contact angle measurements with four probe liquids and X-ray photoelectron spectroscopy (XPS). We investigated the mechanistic reasons for the stark contrast between the PMMA resists and ZEP520A, and it was found that the efficacy of resist removal appeared to be the critical factor in reducing the background functionalization. Differences in the molecular weight of the PMMA resists and the resulting influence on APTMS diffusion through the resist films are unlikely to have a significant impact. Area-selective nanopatterning of 15 nm gold nanoparticles using the ZEP520A resist was demonstrated, with no observable background conjugation noted in the unexposed areas on the silicon surface by SEM.

Chapter 04: Bloodless wood specimen preparation for hand lens observation

Treesearch

Alex Wiedenhoeft

2011-01-01

The single most difficult physical skill involved in wood identification is producing a smoothly prepared surface for observing anatomical features. This skill must be practiced patiently; it takes time to become proficient at this task. Producing a cleanly cut surface is also the only appreciably dangerous aspect of wood identification with a hand lens; the tools used...

Recovery of vancomycin-resistant enterococci on fingertips and environmental surfaces.

PubMed

Noskin, G A; Stosor, V; Cooper, I; Peterson, L R

1995-10-01

To determine the recovery of vancomycin-resistant enterococci (VRE) on fingertips, gloved fingertips, and environmental surfaces commonly encountered in the healthcare setting, and to examine the importance of handwashing on the removal of these organisms. Two clinical isolates of VRE (Enterococcus faecalis and Enterococcus faecium) were inoculated onto the hands of healthy human volunteers and the following environmental surfaces: countertops, bedrails, telephones, and stethoscopes. Following inoculation, samples were obtained at various time intervals to determine rates of recovery of organisms. To evaluate the effects of handwashing on enterococcal recovery, two different soap preparations were tested. Hands were washed with water alone or with one of the soaps and water. The soap and water studies were performed with a 5-second and a 30-second wash. Both enterococcal strains survived for at least 60 minutes on gloved and ungloved fingertips. The E faecalis was recoverable from countertops for 5 days; the E faecium persisted for 7 days. For bedrails, both enterococcal species survived for 24 hours without significant reduction in colony counts. The bacteria persisted for 60 minutes on the telephone handpiece and for 30 minutes on the diaphragmatic surface of the stethoscope. A 5-second wash with water alone resulted in virtually no change in recovery of enterococci; a 30-second wash with water plus either soap was necessary to eradicate the bacteria from hands completely. VRE are capable of prolonged survival on hands, gloves, and environmental surfaces. Hands should be washed thoroughly and gloves removed following contact with patients infected or colonized with these multidrug-resistant bacteria. Finally, environmental surfaces may serve as potential reservoirs for nosocomial transmission of VRE and need to be considered when formulating institutional infection control policies.

Verification of cleaning efficiency and its possible role in programmed hygiene inspections of food businesses undertaken by local authority officers.

PubMed

Tebbutt, G; Bell, V; Aislabie, J

2007-04-01

The aim of this study was to determine whether or not the assessment of surface cleanliness could make a contribution to visual inspections of food premises. Forty-five premises were studied with both rapid (ATP) and traditional microbiological swabbing being used to test surfaces that either come into direct contact with prepared foods or were likely to be touched by hands during food preparation. A significant link was found between aerobic colony counts and ATP measurements. In most cases, the visual appearance of surfaces could not be used to accurately predict either microbial or ATP results. This study suggests that ATP testing is a useful indicator of surface cleanliness and could be helpful to local authority officers as part of risk assessment inspections. This study provides further evidence that visual inspection alone may not always be adequate to assess surface cleanliness. In high-risk premises, ATP could, if appropriately targeted, help identify potential problem areas. The results are available at the time of the inspection and can be used as an on-the-spot teaching aid.

Biofilm Surface Density Determines Biocide Effectiveness

PubMed Central

Bas, Sara; Kramer, Mateja; Stopar, David

2017-01-01

High resistance of biofilms for chemical challenges is a serious industrial and medical problem. In this work a gradient of surface covered with biofilm has been produced and correlated to the effectiveness of different commercially available oxidative biocides. The results for thin Escherichia coli biofilms grown in rich media supplemented with glucose or lactose on glass or poly methyl methacrylate surfaces indicate that the effectiveness of hydrogen peroxide or chlorine dioxide and quaternary ammonium compounds is inversely proportional to the fraction of the surface covered with the biofilm. In areas where biofilm covered more than 90% of the available surface the biocide treatment was inefficient after 60 min of incubation. The combined effect of oxidant and surfactant increased the effectiveness of the biocide. On the other hand, the increased biofilm viscoelasticity reduced biocide effectiveness. The results emphasize differential biocide effectiveness depending on the fraction of the attached bacterial cells. The results suggest that biofilm biocide resistance is an acquired property that increases with biofilm maturation. The more dense sessile structures present lower log reductions compared to less dense ones. PMID:29276508

Terrestrial geophysics in the SeaRISE project

NASA Technical Reports Server (NTRS)

Bentley, C. R.

1991-01-01

Some areas of research in the SeaRISE project are briefly discussed. They are as follows: (1) Radar Sounding serves multiple purposes. The most general and obvious is mapping ice thickness and the surface and bedrock topography of the ice sheet. (2) The purpose of Seismic Shooting, in addition to water depth measurements on floating ice, is to provide information about the internal physical characteristics of the ice sheet, the rock beneath it, and the interface between the two. (3) Passive Seismic monitoring of microearthquakes can be used to study brittle fracture within the ice or the rock beneath it. Common parameters available from these studies are fault location, orientation, and displacement, as well as the size of the rupture area, stress drop, and energy released. (4) There is a large contrast in Electrical Resistivity between ice or permafrost on the one hand and liquid water or wet rock on the other hand. Thus, electrical resistivity profiles have the ability of revealing the depth to the melting point, whether it is found at the base of the ice or in the subglacial rock. (5) Gravity anomalies, especially combined with seismic measurements, are an effective tool for determining deeper crustal structure. Anomalies averaged over extensive areas are useful also for their potential to reveal isostatic imbalance, which is a measure of average glacial change over the last several hundred years.

Characterization of Qatar's surface carbonates for CO2 capture and thermochemical energy storage

NASA Astrophysics Data System (ADS)

Kakosimos, Konstantinos E.; Al-Haddad, Ghadeer; Sakellariou, Kyriaki G.; Pagkoura, Chrysa; Konstandopoulos, Athanasios G.

2017-06-01

Samples of surface carbonates were collected from three different areas of the Qatar peninsula. We employed material characterization techniques to examine the morphology and composition of the samples, while their CO2 capture capacity was assessed via multiple successive calcination-carbonation cycles. Our samples were mainly calcite and dolomite based. Calcite samples showed higher initial capacity of around 11 mmol CO2 g-1 which decayed rapidly to less than 2 mmol CO2 g-1. On the other hand, dolomite samples showed an excellent stability (˜15 cycles) with a capacity of 6 mmol CO2 g-1. The performance of the dolomite samples is better compared to other similar natural samples, from literature. A promising result for future studies towards improving their performance by physical and chemical modification.

Surface EMG in advanced hand prosthetics.

PubMed

Castellini, Claudio; van der Smagt, Patrick

2009-01-01

One of the major problems when dealing with highly dexterous, active hand prostheses is their control by the patient wearing them. With the advances in mechatronics, building prosthetic hands with multiple active degrees of freedom is realisable, but actively controlling the position and especially the exerted force of each finger cannot yet be done naturally. This paper deals with advanced robotic hand control via surface electromyography. Building upon recent results, we show that machine learning, together with a simple downsampling algorithm, can be effectively used to control on-line, in real time, finger position as well as finger force of a highly dexterous robotic hand. The system determines the type of grasp a human subject is willing to use, and the required amount of force involved, with a high degree of accuracy. This represents a remarkable improvement with respect to the state-of-the-art of feed-forward control of dexterous mechanical hands, and opens up a scenario in which amputees will be able to control hand prostheses in a much finer way than it has so far been possible.

Investigations on the micro-scale surface interactions at the tool and workpiece interface in micro-manufacturing of bipolar plates for proton exchange membrane fuel cells

NASA Astrophysics Data System (ADS)

Peker, Mevlut Fatih

Micro-forming studies have been more attractive in recent years because of miniaturization trend. One of the promising metal forming processes, micro-stamping, provides durability, strength, surface finish, and low cost for metal products. Hence, it is considered a prominent method for fabricating bipolar plates (BPP) with micro-channel arrays on large metallic surfaces to be used in Proton Exchange Membrane Fuel Cells (PEMFC). Major concerns in micro-stamping of high volume BPPs are surface interactions between micro-stamping dies and blank metal plates, and tribological changes. These concerns play a critical role in determining the surface quality, channel formation, and dimensional precision of bipolar plates. The surface quality of BPP is highly dependent on the micro-stamping die surface, and process conditions due to large ratios of surface area to volume (size effect) that cause an increased level of friction and wear issues at the contact interface. Due to the high volume and fast production rates, BPP surface characteristics such as surface roughness, hardness, and stiffness may change because of repeated interactions between tool (micro-forming die) and workpiece (sheet blank of interest). Since the surface characteristics of BPPs have a strong effect on corrosion and contact resistance of bipolar plates, and consequently overall fuel cell performance, evolution of surface characteristics at the tool and workpiece should be monitored, controlled, and kept in acceptable ranges throughout the long production cycles to maintain the surface quality. Compared to macro-forming operations, tribological changes in micro-forming process are bigger challenges due to their dominance and criticality. Therefore, tribological size effect should be considered for better understanding of tribological changes in micro-scale. The integrity of process simulation to the experiments, on the other hand, is essential. This study describes an approach that aims to investigate the surface topography changes during long-run micro-stamping of BPPs, and establish relationships between surface roughness--corrosion resistance and surface roughness-contact resistance characteristics of BPPs. Formability levels of formed BPPs and repeatability characteristics of the process were investigated. In addition, blank thickness changes, von-Mises stress, plastic strain levels and distributions of micro-stamping process were determined via finite element analysis (FEA). Test results revealed that the surface roughness change for the stamping dies and BPPs was unsteady (no trend) due to the continuous change of surface topography (i.e. asperity deformation). Sub-micron range local plastic deformations on stamping dies led to surface topography changes on BPP in long-run manufacturing case. As surface defects trigger corrosion, the correlation between surface roughness and corrosion resistance of BPPs was found to be direct. Increasing number of surface irregularities (asperities) lowered contact surface area that resulted in increased contact resistance. ZrN coated BPPs, on the other hand, did not change surface roughness, however; it improved the protection of BPPs against corrosion significantly. In addition, ZrN coating increased the conductivity of BPPs and reduced the contact resistance between BPP and gas diffusion layer (GDL), at certain extent. As dimensional stability and repeatability was confirmed in forming of both uncoated and coated BPPs during the long run manufacturing, different formability levels were achieved for coated and uncoated samples. Lower channel height values were obtained for coated plates because of the different surface hardness of uncoated and coated plates. In tribological size effect part of study, micro stamping experiments using three different dies with distinct channel height values at different stamping force levels were performed. It was concluded that decrease in forming die dimensions led to increase in coefficient of friction as previously reported by other researchers as one of the consequences of tribological size effect. On the other hand, coefficient of friction values were not affected by the force levels used in the experiments and simulations, whereas plastic strain, equivalent stress, and formability levels were increased with increasing stamping force, as expected. In essence, this study proposed a methodology to investigate the long-run manufacturing effects on dimensional stability and surface characteristics of micro-stamped sheets. It also correlates these parameters to fuel cell performance measures such as interfacial contact and corrosion resistance.

Cortical Asymmetries during Hand Laterality Task Vary with Hand Laterality: A fMRI Study in 295 Participants

PubMed Central

Mellet, Emmanuel; Mazoyer, Bernard; Leroux, Gaelle; Joliot, Marc; Tzourio-Mazoyer, Nathalie

2016-01-01

The aim of this study was to characterize, using fMRI, the functional asymmetries of hand laterality task (HLT) in a sample of 295 participants balanced for handedness. During HLT, participants have to decide whether the displayed picture of a hand represent a right or a left hand. Pictures of hands’ back view were presented for 150 ms in the right or left hemifield. At the whole hemisphere level, we evidenced that the laterality of the hand and of the hemifield in which the picture was displayed combined their effects on the hemispheric asymmetry in an additive way. We then identified a set of 17 functional homotopic regions of interest (hROIs) including premotor, motor, somatosensory and parietal regions, whose activity and asymmetry varied with the laterality of the presented hands. When the laterality of a right hand had to be evaluated, these areas showed stronger leftward asymmetry, the hROI located in the primary motor area showing a significant larger effect than all other hROIs. In addition a subset of six parietal regions involved in visuo-motor integration together with two postcentral areas showed a variation in asymmetry with hemifield of presentation. Finally, while handedness had no effect at the hemispheric level, two regions located in the parietal operculum and intraparietal sulcus exhibited larger leftward asymmetry with right handedness independently of the hand of presentation. The present results extend those of previous works in showing a shift of asymmetries during HLT according to the hand presented in sensorimotor areas including primary motor cortex. This shift was not affected by manual preference. They also demonstrate that the coordination of visual information and handedness identification of hands relied on the coexistence of contralateral motor and visual representations in the superior parietal lobe and the postcentral gyrus. PMID:27999536

The 3-D vision system integrated dexterous hand

NASA Technical Reports Server (NTRS)

Luo, Ren C.; Han, Youn-Sik

1989-01-01

Most multifingered hands use a tendon mechanism to minimize the size and weight of the hand. Such tendon mechanisms suffer from the problems of striction and friction of the tendons resulting in a reduction of control accuracy. A design for a 3-D vision system integrated dexterous hand with motor control is described which overcomes these problems. The proposed hand is composed of three three-jointed grasping fingers with tactile sensors on their tips, a two-jointed eye finger with a cross-shaped laser beam emitting diode in its distal part. The two non-grasping fingers allow 3-D vision capability and can rotate around the hand to see and measure the sides of grasped objects and the task environment. An algorithm that determines the range and local orientation of the contact surface using a cross-shaped laser beam is introduced along with some potential applications. An efficient method for finger force calculation is presented which uses the measured contact surface normals of an object.

Representation of continuous hand and arm movements in macaque areas M1, F5, and AIP: a comparative decoding study

NASA Astrophysics Data System (ADS)

Menz, Veera Katharina; Schaffelhofer, Stefan; Scherberger, Hansjörg

2015-10-01

Objective. In the last decade, multiple brain areas have been investigated with respect to their decoding capability of continuous arm or hand movements. So far, these studies have mainly focused on motor or premotor areas like M1 and F5. However, there is accumulating evidence that anterior intraparietal area (AIP) in the parietal cortex also contains information about continuous movement. Approach. In this study, we decoded 27 degrees of freedom representing complete hand and arm kinematics during a delayed grasping task from simultaneously recorded activity in areas M1, F5, and AIP of two macaque monkeys (Macaca mulatta). Main results. We found that all three areas provided decoding performances that lay significantly above chance. In particular, M1 yielded highest decoding accuracy followed by F5 and AIP. Furthermore, we provide support for the notion that AIP does not only code categorical visual features of objects to be grasped, but also contains a substantial amount of temporal kinematic information. Significance. This fact could be utilized in future developments of neural interfaces restoring hand and arm movements.

Elevated Radiation Exposure Associated With Above Surface Flat Detector Mini C-Arm Use.

PubMed

Martin, Dennis P; Chapman, Talia; Williamson, Christopher; Tinsley, Brian; Ilyas, Asif M; Wang, Mark L

2017-11-01

This study aims to test the hypothesis that: (1) radiation exposure is increased with the intended use of Flat Surface Image Intensifier (FSII) units above the operative surface compared with the traditional below-table configuration; (2) this differential increases in a dose-dependent manner; and (3) radiation exposure varies with body part and proximity to the radiation source. A surgeon mannequin was seated at a radiolucent hand table, positioned for volar distal radius plating. Thermoluminescent dosimeters measured exposure to the eyes, thyroid, chest, hand, and groin, for 1- and 15-minute trials from a mini C-arm FSII unit positioned above and below the operating surface. Background radiation was measured by control dosimeters placed within the operating theater. At 1-minute of exposure, hand and eye dosages were significantly greater with the flat detector positioned above the table. At 15-minutes of exposure, hand radiation dosage exceeded that of all other anatomic sites with the FSII in both positions. Hand exposure was increased in a dose-dependent manner with the flat detector in either position, whereas groin exposure saw a dose-dependent only with the flat detector beneath the operating table. These findings suggest that the surgeon's hands and eyes may incur greater radiation exposure compared with other body parts, during routine mini C-arm FSII utilization in its intended position above the operating table. The clinical impact of these findings remains unclear, and future long-term radiation safety investigation is warranted. Surgeons should take precautions to protect critical body parts, particularly when using FSII technology above the operating with prolonged exposure time.

Implementation of whole body scanner for determining somatotype index at Chang Gung Memorial Hospital.

PubMed

Liu, T H; Chiou, W K; Lin, J D; Yu, C Y

2001-11-01

Body mass index (BMI) and waist-hip ratio (WHR) using 1-dimensional circumference data have been proven to be highly related to blood pressure and total cholesterol; these 2 indices have been widely used as health indicators in preventive diagnosis and health examination. Sophisticated software, which allows calculation of the triangular mesh related to the body surface in 3D space, is capable of computing the circumference, width, sectional surface, volume, and surface area of the body. Chang Gung Whole Body Scanner (CGWBS) was used to capture 3D whole body surface images. In this study, the human body was divided into 10 segments consisting of the head, breast, wrist, hip, upper arm, forearm, hand, thigh, calf, and foot. Five independent assessments were made on a total of 32 anthropometric sites, including 12 circumferences, 3 widths, 3 profile areas, 7 surface areas, and 7 volumes. In this study, the somatotype index (SI) was computed through anthropometric data after 1,323 subjects were investigated. Correlation analysis was used to describe the relationship between BMI, WHR, SI, and anthropometric data. One-way analysis of variance (ANOVA) and Duncan's multiple range tests were used to examine differences between examination variables across sex and SI groups. This study found 4 somatotypes from anthropometric data. SI determined by CGWBS has better correlation with anthropometry than WHR or BMI. Of the 644 male subjects, 155 were in the ectomorph group, 232 in the semi-mesomorph group, 136 in the full-mesomorph group, and 121 in the endomorph group. Of the 679 female subjects, 160 were in the ectomorph group, 235 in the semi-mesomorph group, 168 in the full-mesomorph group, and 116 in the endomorph group. The results show that SI has great potential to perform precise somatotype classification.

Default values for assessment of potential dermal exposure of the hands to industrial chemicals in the scope of regulatory risk assessments.

PubMed

Marquart, Hans; Warren, Nicholas D; Laitinen, Juha; van Hemmen, Joop J

2006-07-01

Dermal exposure needs to be addressed in regulatory risk assessment of chemicals. The models used so far are based on very limited data. The EU project RISKOFDERM has gathered a large number of new measurements on dermal exposure to industrial chemicals in various work situations, together with information on possible determinants of exposure. These data and information, together with some non-RISKOFDERM data were used to derive default values for potential dermal exposure of the hands for so-called 'TGD exposure scenarios'. TGD exposure scenarios have similar values for some very important determinant(s) of dermal exposure, such as amount of substance used. They form narrower bands within the so-called 'RISKOFDERM scenarios', which cluster exposure situations according to the same purpose of use of the products. The RISKOFDERM scenarios in turn are narrower bands within the so-called Dermal Exposure Operation units (DEO units) that were defined in the RISKOFDERM project to cluster situations with similar exposure processes and exposure routes. Default values for both reasonable worst case situations and typical situations were derived, both for single datasets and, where possible, for combined datasets that fit the same TGD exposure scenario. The following reasonable worst case potential hand exposures were derived from combined datasets: (i) loading and filling of large containers (or mixers) with large amounts (many litres) of liquids: 11,500 mg per scenario (14 mg cm(-2) per scenario with surface of the hands assumed to be 820 cm(2)); (ii) careful mixing of small quantities (tens of grams in <1l): 4.1 mg per scenario (0.005 mg cm(-2) per scenario); (iii) spreading of (viscous) liquids with a comb on a large surface area: 130 mg per scenario (0.16 mg cm(-2) per scenario); (iv) brushing and rolling of (relatively viscous) liquid products on surfaces: 6500 mg per scenario (8 mg cm(-2) per scenario) and (v) spraying large amounts of liquids (paints, cleaning products) on large areas: 12,000 mg per scenario (14 mg cm(-2) per scenario). These default values are considered useful for estimating exposure for similar substances in similar situations with low uncertainty. Several other default values based on single datasets can also be used, but lead to estimates with a higher uncertainty, due to their more limited basis. Sufficient analogy in all described parameters of the scenario, including duration, is needed to enable proper use of the default values. The default values lead to similar estimates as the RISKOFDERM dermal exposure model that was based on the same datasets, but uses very different parameters. Both approaches are preferred over older general models, such as EASE, that are not based on data from actual dermal exposure situations.

Virtual hand: a 3D tactile interface to virtual environments

NASA Astrophysics Data System (ADS)

Rogowitz, Bernice E.; Borrel, Paul

2008-02-01

We introduce a novel system that allows users to experience the sensation of touch in a computer graphics environment. In this system, the user places his/her hand on an array of pins, which is moved about space on a 6 degree-of-freedom robot arm. The surface of the pins defines a surface in the virtual world. This "virtual hand" can move about the virtual world. When the virtual hand encounters an object in the virtual world, the heights of the pins are adjusted so that they represent the object's shape, surface, and texture. A control system integrates pin and robot arm motions to transmit information about objects in the computer graphics world to the user. It also allows the user to edit, change and move the virtual objects, shapes and textures. This system provides a general framework for touching, manipulating, and modifying objects in a 3-D computer graphics environment, which may be useful in a wide range of applications, including computer games, computer aided design systems, and immersive virtual worlds.

Geomorphological characterization of conservation agriculture

NASA Astrophysics Data System (ADS)

Tarolli, Paolo; Cecchin, Marco; Prosdocimi, Massimo; Masin, Roberta

2017-04-01

Soil water erosion is one of the major threats to soil resources throughout the world. Conventional agriculture has worsened the situation. Therefore, agriculture is facing multiple challenges: it has to produce more food to feed a growing population, and, on the other hand, safeguard natural resources adopting more sustainable production practices. In this perspective, more conservation-minded soil management practices should be taken to achieve an environmental sustainability of crop production. Indeed, conservation agriculture is considered to produce relevant environmental positive outcomes (e.g. reducing runoff and soil erosion, improving soil organic matter content and soil structure, and promoting biological activity). However, as mechanical weed control is limited or absent, in conservation agriculture, dependence on herbicides increases especially in the first years of transition from the conventional system. Consequently, also the risk of herbicide losses via runoff or adsorbed to eroded soil particles could be increased. To better analyse the complexity of soil water erosion and runoff processes in landscapes characterised by conservation agriculture, first, it is necessary to demonstrate if such different practices can significantly affect the surface morphology. Indeed, surface processes such erosion and runoff strongly depend on the shape of the surface. The questions are: are the lands treated with conservation and conventional agriculture different from each other regarding surface morphology? If so, can these differences provide a better understanding of hydrogeomorphic processes as the basis for a better and sustainable land management? To give an answer to these questions, we considered six study areas (three cultivated with no-tillage techniques, three with tillage techniques) in an experimental farm. High-resolution topography, derived from low-cost and fast photogrammetric techniques Structure-from-Motion (SfM), served as the basis to characterise the surface morphology. For each of derived Digital Elevation Model, seven morphometric indexes, such as slope, curvature, flow direction, contributing area, roughness, and connectivity was calculated. We showed then the variations of the morphology in the areas converted to the conservation agriculture, and, consequently, a possible modification of processes such as erosion and runoff. The results suggested that the agricultural surfaces interested by no-tillage practices are different from those tilled with conventional systems. The topography is rougher, with chaotic flow directions, and more concave areas, thus resulting in potential water storages, mitigating the intensity of soil erosion and runoff processes. On the other hand, the topography of traditional tillage area is more regular and smooth, with flow directions that tend to follow the same direction on the surface. These results are a novelty in the Earth Science and Agronomy: we demonstrated and quantified, from the geomorphological point of view, the potential role of conservative agriculture in mitigating, not only land degradation phenomena, but also the distribution of pollutants, and rainfall-runoff processes. References Prosdocimi, M., Tarolli, P., Cerdà, A. (2016). Mulching practice for reducing soil water erosion: A review. Earth-Science Reviews, 161, 191-203. Prosdocimi, M., Burguet, M., Di Prima, S., Sofia, G., Terol, E, Rodrigo Comino J., Cerdà, A., Tarolli, P. (2017). Rainfall simulation and Structure-from-Motion photogrammetry for the analysis of soil water erosion in Mediterranean vineyards. Science of the Total Environment, 574, 204-215. Tarolli, P., Sofia G. (2016). Human topographic signatures and derived geomorphic processes across landscapes, Geomorphology, 255, 140-161.

Expansion of Smartwatch Touch Interface from Touchscreen to Around Device Interface Using Infrared Line Image Sensors.

PubMed

Lim, Soo-Chul; Shin, Jungsoon; Kim, Seung-Chan; Park, Joonah

2015-07-09

Touchscreen interaction has become a fundamental means of controlling mobile phones and smartwatches. However, the small form factor of a smartwatch limits the available interactive surface area. To overcome this limitation, we propose the expansion of the touch region of the screen to the back of the user's hand. We developed a touch module for sensing the touched finger position on the back of the hand using infrared (IR) line image sensors, based on the calibrated IR intensity and the maximum intensity region of an IR array. For complete touch-sensing solution, a gyroscope installed in the smartwatch is used to read the wrist gestures. The gyroscope incorporates a dynamic time warping gesture recognition algorithm for eliminating unintended touch inputs during the free motion of the wrist while wearing the smartwatch. The prototype of the developed sensing module was implemented in a commercial smartwatch, and it was confirmed that the sensed positional information of the finger when it was used to touch the back of the hand could be used to control the smartwatch graphical user interface. Our system not only affords a novel experience for smartwatch users, but also provides a basis for developing other useful interfaces.

Mud Flow Characteristics Occurred in Izuoshima Island, 2013

NASA Astrophysics Data System (ADS)

Takebayashi, H.; Egashira, S.; Fujita, M.

2015-12-01

Landslides and mud flows were occurred in the west part of the Izuoshima Island, Japan on 16 October 2013. The Izuoshima Island is a volcanic island and the land surface is covered by the volcanic ash sediment in 1m depth. Hence, the mud flow with high sediment concentration was formed. The laminar layer is formed in the debris flow from the bed to the fluid surface. On the other hand, the laminar flow is restricted near the bed in the mud flow and the turbulence flow is formed on the laminar flow layer. As a result, the equilibrium slope of the mud flow becomes smaller comparing to the debris flow. In this study, the numerical analysis mud flow model considering the effect of turbulence flow on the equilibrium slope of the mud flow is developed. Subsequently, the model is applied to the mud flow occurred in the Izuoshima Island and discussed the applicability of the model and the flow characteristics of the mud flow. The differences of the horizontal flow areas between the simulated results and the field data are compared and it was found that the outline of the horizontal shape of the flow areas is reproduced well. Furthermore, the horizontal distribution of the erosion and deposition area is reproduced by the numerical analysis well except for the residential area (Kandachi area). Kandachi area is judged as the erosion area by the field observation, but the sediment was deposited in the numerical analysis. It is considered that the 1.5hour heavy rain over 100mm/h after the mud flow makes the discrepancy. The difference of the horizontal distribution of the maximum flow surface elevation between the simulated results and the field data are compared and it was found that the simulated flow depth is overestimated slightly, because of the wider erosion area due to the coarse resolution elevation data. The averaged velocity and the depth of the mud flow was enough large to collapse the houses.

Is Agency Skin Deep? Surface Attributes Influence Infants' Sensitivity to Goal-Directed Action

ERIC Educational Resources Information Center

Guajardo, Jose J.; Woodward, Amanda L.

2004-01-01

Three studies investigated the role of surface attributes in infants' identification of agents, using a habituation paradigm designed to tap infants' interpretation of grasping as goal directed (Woodward, 1998). When they viewed a bare human hand grasping objects, 7- and 12-month-old infants focused on the relation between the hand and its goal.…

DEVELOPMENT OF EVALUATION OF A QUANTITATIVE VIDEO-FLUORESCENCE IMAGING SYSTEM AND FLUORESCENT TRACER FOR MEASURING TRANSFER OF PESTICIDE RESIDUES FROM SURFACES TO HANDS WITH REPEATED CONTACTS

EPA Science Inventory

A video imaging system and the associated quantification methods have been developed for measurement of the transfers of a fluorescent tracer from surfaces to hands. The highly fluorescent compound riboflavin (Vitamin B2), which is also water soluble and non-toxic, was chosen as...

Ultra-weak photon emission of hands in aging prediction.

PubMed

Zhao, Xin; van Wijk, Eduard; Yan, Yu; van Wijk, Roeland; Yang, Huanming; Zhang, Yan; Wang, Jian

2016-09-01

Aging has been one of the several topics intensely investigated during recent decades. More scientists have been scrutinizing mechanisms behind the human aging process. Ultra-weak photon emission is known as one type of spontaneous photon emission that can be detected with a highly sensitive single photon counting photomultiplier tube (PMT) from the surface of human bodies. It may reflect the body's oxidative damage. Our aim was to examine whether ultra-weak photon emission from a human hand is able to predict one's chronological age. Sixty subjects were recruited and grouped by age. We examined four areas of each hand: palm side of fingers, palm side of hand, dorsum side of fingers, and dorsum side of hand. Left and right hand were measured synchronously with two independent PMTs. Mean strength and Fano factor values of photon counts were utilized to compare the UPE patterns of males and females of different age groups. Subsequently, we utilized UPE data from the most sensitive PMT to develop an age prediction model. We randomly picked 49 subjects to construct the model, whereas the remaining 11 subjects were utilized for validation. The results demonstrated that the model was a good regression compared to the observed values (Pearson's r=0.6, adjusted R square=0.4, p=9.4E-7, accuracy=49/60). Further analysis revealed that the average difference between the chronological age and predicted age was only 7.6±0.8years. It was concluded that this fast and non-invasive photon technology is sufficiently promising to be developed for the estimation of biological aging. Copyright © 2016 Elsevier B.V. All rights reserved.

Three-dimensional fluorescence-enhanced optical tomography using a hand-held probe based imaging system

PubMed Central

Ge, Jiajia; Zhu, Banghe; Regalado, Steven; Godavarty, Anuradha

2008-01-01

Hand-held based optical imaging systems are a recent development towards diagnostic imaging of breast cancer. To date, all the hand-held based optical imagers are used to perform only surface mapping and target localization, but are not capable of demonstrating tomographic imaging. Herein, a novel hand-held probe based optical imager is developed towards three-dimensional (3-D) optical tomography studies. The unique features of this optical imager, which primarily consists of a hand-held probe and an intensified charge coupled device detector, are its ability to; (i) image large tissue areas (5×10 sq. cm) in a single scan, (ii) perform simultaneous multiple point illumination and collection, thus reducing the overall imaging time; and (iii) adapt to varying tissue curvatures, from a flexible probe head design. Experimental studies are performed in the frequency domain on large slab phantoms (∼650 ml) using fluorescence target(s) under perfect uptake (1:0) contrast ratios, and varying target depths (1–2 cm) and X-Y locations. The effect of implementing simultaneous over sequential multiple point illumination towards 3-D tomography is experimentally demonstrated. The feasibility of 3-D optical tomography studies has been demonstrated for the first time using a hand-held based optical imager. Preliminary fluorescence-enhanced optical tomography studies are able to reconstruct 0.45 ml target(s) located at different target depths (1–2 cm). However, the depth recovery was limited as the actual target depth increased, since only reflectance measurements were acquired. Extensive tomography studies are currently carried out to determine the resolution and performance limits of the imager on flat and curved phantoms. PMID:18697559

Three-dimensional fluorescence-enhanced optical tomography using a hand-held probe based imaging system.

PubMed

Ge, Jiajia; Zhu, Banghe; Regalado, Steven; Godavarty, Anuradha

2008-07-01

Hand-held based optical imaging systems are a recent development towards diagnostic imaging of breast cancer. To date, all the hand-held based optical imagers are used to perform only surface mapping and target localization, but are not capable of demonstrating tomographic imaging. Herein, a novel hand-held probe based optical imager is developed towards three-dimensional (3-D) optical tomography studies. The unique features of this optical imager, which primarily consists of a hand-held probe and an intensified charge coupled device detector, are its ability to; (i) image large tissue areas (5 x 10 sq. cm) in a single scan, (ii) perform simultaneous multiple point illumination and collection, thus reducing the overall imaging time; and (iii) adapt to varying tissue curvatures, from a flexible probe head design. Experimental studies are performed in the frequency domain on large slab phantoms (approximately 650 ml) using fluorescence target(s) under perfect uptake (1:0) contrast ratios, and varying target depths (1-2 cm) and X-Y locations. The effect of implementing simultaneous over sequential multiple point illumination towards 3-D tomography is experimentally demonstrated. The feasibility of 3-D optical tomography studies has been demonstrated for the first time using a hand-held based optical imager. Preliminary fluorescence-enhanced optical tomography studies are able to reconstruct 0.45 ml target(s) located at different target depths (1-2 cm). However, the depth recovery was limited as the actual target depth increased, since only reflectance measurements were acquired. Extensive tomography studies are currently carried out to determine the resolution and performance limits of the imager on flat and curved phantoms.

Modeling groundwater/surface-water interactions in an Alpine valley (the Aosta Plain, NW Italy): the effect of groundwater abstraction on surface-water resources

NASA Astrophysics Data System (ADS)

Stefania, Gennaro A.; Rotiroti, Marco; Fumagalli, Letizia; Simonetto, Fulvio; Capodaglio, Pietro; Zanotti, Chiara; Bonomi, Tullia

2018-02-01

A groundwater flow model of the Alpine valley aquifer in the Aosta Plain (NW Italy) showed that well pumping can induce river streamflow depletions as a function of well location. Analysis of the water budget showed that ˜80% of the water pumped during 2 years by a selected well in the downstream area comes from the baseflow of the main river discharge. Alluvial aquifers hosted in Alpine valleys fall within a particular hydrogeological context where groundwater/surface-water relationships change from upstream to downstream as well as seasonally. A transient groundwater model using MODFLOW2005 and the Streamflow-Routing (SFR2) Package is here presented, aimed at investigating water exchanges between the main regional river (Dora Baltea River, a left-hand tributary of the Po River), its tributaries and the underlying shallow aquifer, which is affected by seasonal oscillations. The three-dimensional distribution of the hydraulic conductivity of the aquifer was obtained by means of a specific coding system within the database TANGRAM. Both head and flux targets were used to perform the model calibration using PEST. Results showed that the fluctuations of the water table play an important role in groundwater/surface-water interconnections. In upstream areas, groundwater is recharged by water leaking through the riverbed and the well abstraction component of the water budget changes as a function of the hydraulic conditions of the aquifer. In downstream areas, groundwater is drained by the river and most of the water pumped by wells comes from the base flow component of the river discharge.

Clouds and Ice of the Lambert-Amery System, East Antarctica

NASA Technical Reports Server (NTRS)

2002-01-01

These views from the Multi-angle Imaging SpectroRadiometer (MISR) illustrate ice surface textures and cloud-top heights over the Amery Ice Shelf/Lambert Glacier system in East Antarctica on October 25, 2002.

The left-hand panel is a natural-color view from MISR's downward-looking (nadir) camera. The center panel is a multi-angular composite from three MISR cameras, in which color acts as a proxy for angular reflectance variations related to texture. Here, data from the red-band of MISR's 60o forward-viewing, nadir and 60o backward-viewing cameras are displayed as red, green and blue, respectively. With this display technique, surfaces which predominantly exhibit backward-scattering (generally rough surfaces) appear red/orange, while surfaces which predominantly exhibit forward-scattering (generally smooth surfaces) appear blue. Textural variation for both the grounded and sea ice are apparent. The red/orange pixels in the lower portion of the image correspond with a rough and crevassed region near the grounding zone, that is, the area where the Lambert and four other smaller glaciers merge and the ice starts to float as it forms the Amery Ice Shelf. In the natural-color view, this rough ice is spectrally blue in color.

Clouds exhibit both forward and backward-scattering properties in the middle panel and thus appear purple, in distinct contrast with the underlying ice and snow. An additional multi-angular technique for differentiating clouds from ice is shown in the right-hand panel, which is a stereoscopically derived height field retrieved using automated pattern recognition involving data from multiple MISR cameras. Areas exhibiting insufficient spatial contrast for stereoscopic retrieval are shown in dark gray. Clouds are apparent as a result of their heights above the surface terrain. Polar clouds are an important factor in weather and climate. Inadequate characterization of cloud properties is currently responsible for large uncertainties in climate prediction models. Identification of polar clouds, mapping of their distributions, and retrieval of their heights provide information that will help to reduce this uncertainty.

The Multi-angle Imaging SpectroRadiometer observes the daylit Earth continuously and every 9 days views the entire Earth between 82 degrees north and 82 degrees south latitude. These data products were generated from a portion of the imagery acquired during Terra orbit 15171. The panels cover an area of 380 kilometers x 984 kilometers, and utilize data from blocks 145 to 151 within World Reference System-2 path 127.

MISR was built and is managed by NASA's Jet Propulsion Laboratory,Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center,Greenbelt, MD. JPL is a division of the California Institute of Technology.

An fMRI study of musicians with focal dystonia during tapping tasks.

PubMed

Kadota, Hiroshi; Nakajima, Yasoichi; Miyazaki, Makoto; Sekiguchi, Hirofumi; Kohno, Yutaka; Amako, Masatoshi; Arino, Hiroshi; Nemoto, Koichi; Sakai, Naotaka

2010-07-01

Musician's dystonia is a type of task specific dystonia for which the pathophysiology is not clear. In this study, we performed functional magnetic resonance imaging to investigate the motor-related brain activity associated with musician's dystonia. We compared brain activities measured from subjects with focal hand dystonia and normal (control) musicians during right-hand, left-hand, and both-hands tapping tasks. We found activations in the thalamus and the basal ganglia during the tapping tasks in the control group but not in the dystonia group. For both groups, we detected significant activations in the contralateral sensorimotor areas, including the premotor area and cerebellum, during each tapping task. Moreover, direct comparison between the dystonia and control groups showed that the dystonia group had greater activity in the ipsilateral premotor area during the right-hand tapping task and less activity in the left cerebellum during the both-hands tapping task. Thus, the dystonic musicians showed irregular activation patterns in the motor-association system. We suggest that irregular neural activity patterns in dystonic subjects reflect dystonic neural malfunction and consequent compensatory activity to maintain appropriate voluntary movements.

RCCM2-BATS model over tropical South America: Applications to tropical deforestation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hahmann, A.N.; Dickinson, R.E.

A multiyear simulation of the global climate uses a revised version of the National Center for Atmospheric Research (NCAR) Community Climate Model Version 2 (CCM2) coupled to the Biosphere-Atmosphere Transfer Scheme (BATS). It is compared with global and rain gauge precipitation climatologies to evaluate precipitation fields and European Centre for Medium-Range Forecasts analyses to evaluate the atmospheric circulation. The near-surface climate is compared with data from Amazonian field campaigns. The model simulation of the South American climate agrees closely with the observational record and is much improved from past simulations with previous versions of the NCAR Community Climate model overmore » this portion of the Tropics. The model is then used to study the local and regional response to tropical deforestation over Amazonia. In addition to the standard deforestation forcing, consisting mainly of increased albedo and decreased roughness length, two additional sensitivity experiments were conducted to assess the individual contributions from these forcings to the deforestation changes. The standard deforestation simulation shows slight increases in annually averaged surface temperature (+1{degrees}C) and reductions in annually averaged precipitation and evaporation (-363 and -149 mm yr{sup -1}, respectively). As expected, increases in surface albedo over Amazonia produce a reduction in net downward solar radiation at the surface and consequently a reduction in net surface radiation and surface latent heat flux. The roughness decrease, on the other hand, reduces the surface latent heat fluxes through decreases in the surface drag coefficient. The regional changes in moisture convergence and precipitation during the Amazonian wet season display a shift in the area of maximum precipitation rather than an overall decrease over the deforested area. 45 refs., 16 figs., 4 tabs.« less

Analyzing the effect of cutting parameters on surface roughness and tool wear when machining nickel based hastelloy - 276

NASA Astrophysics Data System (ADS)

Khidhir, Basim A.; Mohamed, Bashir

2011-02-01

Machining parameters has an important factor on tool wear and surface finish, for that the manufacturers need to obtain optimal operating parameters with a minimum set of experiments as well as minimizing the simulations in order to reduce machining set up costs. The cutting speed is one of the most important cutting parameter to evaluate, it clearly most influences on one hand, tool life, tool stability, and cutting process quality, and on the other hand controls production flow. Due to more demanding manufacturing systems, the requirements for reliable technological information have increased. For a reliable analysis in cutting, the cutting zone (tip insert-workpiece-chip system) as the mechanics of cutting in this area are very complicated, the chip is formed in the shear plane (entrance the shear zone) and is shape in the sliding plane. The temperature contributed in the primary shear, chamfer and sticking, sliding zones are expressed as a function of unknown shear angle on the rake face and temperature modified flow stress in each zone. The experiments were carried out on a CNC lathe and surface finish and tool tip wear are measured in process. Machining experiments are conducted. Reasonable agreement is observed under turning with high depth of cut. Results of this research help to guide the design of new cutting tool materials and the studies on evaluation of machining parameters to further advance the productivity of nickel based alloy Hastelloy - 276 machining.

30 CFR 56.14116 - Hand-held power tools.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Hand-held power tools. 56.14116 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 56.14116 Hand-held power tools. (a) Power drills...

30 CFR 56.14116 - Hand-held power tools.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Hand-held power tools. 56.14116 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 56.14116 Hand-held power tools. (a) Power drills...

30 CFR 56.14116 - Hand-held power tools.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Hand-held power tools. 56.14116 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 56.14116 Hand-held power tools. (a) Power drills...

30 CFR 56.14116 - Hand-held power tools.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Hand-held power tools. 56.14116 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 56.14116 Hand-held power tools. (a) Power drills...

30 CFR 56.14116 - Hand-held power tools.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Hand-held power tools. 56.14116 Section 56... MINE SAFETY AND HEALTH SAFETY AND HEALTH STANDARDS-SURFACE METAL AND NONMETAL MINES Machinery and Equipment Safety Devices and Maintenance Requirements § 56.14116 Hand-held power tools. (a) Power drills...

Modeling Coupled Landscape Evolution and Soil Organic Carbon Dynamics in Intensively Management Landscapes

NASA Astrophysics Data System (ADS)

Yan, Q.; Kumar, P.

2017-12-01

Soil is the largest reservoir of carbon in the biosphere but in agricultural areas it is going through rapid erosion due disturbance arising from crop harvest, tillage, and tile drainage. Identifying whether the production of soil organic carbon (SOC) from the crops can compensate for the loss due to erosion is critical to ensure our food security and adapt to climate change. In the U.S. Midwest where large areas of land are intensively managed for agriculture practices, predicting soil quantity and quality are critical for maintaining crop yield and other Critical Zone services. This work focuses on modeling the coupled landscape evolutions soil organic carbon dynamics in agricultural fields. It couples landscape evolution, surface water runoff, organic matter transformation, and soil moisture dynamics to understand organic carbon gain and loss due to natural forcing and farming practices, such as fertilizer application and tillage. A distinctive feature of the model is the coupling of surface ad subsurface processes that predicts both surficial changes and transport along with the vertical transport and dynamics. Our results show that landscape evolution and farming practices play dominant roles in soil organic carbon (SOC) dynamics both above- and below-ground. Contrary to the common assumption that a vertical profile of SOC concentration decreases exponentially with depth, we find that in many situations SOC concentration below-ground could be higher than that at the surface. Tillage plays a complex role in organic matter dynamics. On one hand, tillage would accelerate the erosion rate, on the other hand, it would improve carbon storage by burying surface SOC into below ground. Our model consistently reproduces the observed above- and below-ground patterns of SOC in the field sites of Intensively Managed Landscapes Critical Zone Observatory (IMLCZO). This model bridges the gaps between the landscape evolution, below- and above-ground hydrologic cycle, and biogeochemical processes. This study not only helps us understand the coupled carbon-nitrogen cycle, but also serve as an instrument to develop practical approaches for reducing soil erosion and carbon loss when the landscape is affected by human activities.

Reducing health care-associated infections by implementing separated environmental cleaning management measures by using disposable wipes of four colors.

PubMed

Wong, Swee Siang; Huang, Cheng Hua; Yang, Chiu Chu; Hsieh, Yi Pei; Kuo, Chen Ni; Chen, Yi Ru; Chen, Li Ching

2018-01-01

Environmental cleaning is a fundamental principle of infection control in health care settings. We determined whether implementing separated environmental cleaning management measures in MICU reduced the density of HAI. We performed a 4-month prospective cohort intervention study between August and December 2013, at the MICU of Cathay General hospital. We arranged a training program for all the cleaning staff regarding separated environmental cleaning management measures by using disposable wipes of four colors to clean the patients' bedside areas, areas at a high risk of contamination, paperwork areas, and public areas. Fifteen high-touch surfaces were selected for cleanliness evaluation by using the adenosine triphosphate (ATP) bioluminescence test. Then data regarding HAI densities in the MICU were collected during the baseline, intervention, and late periods. A total of 120 ATP readings were obtained. The total number of clean high-touch surfaces increased from 13% to 53%, whereas that of unclean high-touch surface decreased from 47% to 20%. The densities of HAI were 14.32‰ and 14.90‰ during the baseline and intervention periods, respectively. The HAI density did not decrease after the intervention period, but it decreased to 9.07‰ during the late period. Implementing separated environmental cleaning management measures by using disposable wipes of four colors effectively improves cleanliness in MICU environments. However, no decrease in HAI density was observed within the study period. Considering that achieving high levels of hand-hygiene adherence is difficult, improving environmental cleaning is a crucial adjunctive measure for reducing the incidence of HAIs.

A Prospective Study of Injuries and Injury Risk Factors Among Army Wheel Vehicle Mechanics

DTIC Science & Technology

2006-08-01

metacarpalphalangeal joint and 110* at the proximal interphalangeal joint of the third finger . While keeping the forearm on the padded table surface...ground, then return to the starting point with elbows fully extended. For sit-up, the Soldier bent his knees at a 90’ angle, interlocked his fingers ...Wrist 5 5.4 Hand 2 2.2 Finger 3 3.3 Upper Back 1 1.1 Lower Back Lower Back 16 17.4 Pelvic Area 1 1.1 Anterior Thigh 1 1.1 Knee 17 18.5 Lower Body Calf 1

Online Bimanual Manipulation Using Surface Electromyography and Incremental Learning.

PubMed

Strazzulla, Ilaria; Nowak, Markus; Controzzi, Marco; Cipriani, Christian; Castellini, Claudio

2017-03-01

The paradigm of simultaneous and proportional myocontrol of hand prostheses is gaining momentum in the rehabilitation robotics community. As opposed to the traditional surface electromyography classification schema, in simultaneous and proportional control the desired force/torque at each degree of freedom of the hand/wrist is predicted in real-time, giving to the individual a more natural experience, reducing the cognitive effort and improving his dexterity in daily-life activities. In this study we apply such an approach in a realistic manipulation scenario, using 10 non-linear incremental regression machines to predict the desired torques for each motor of two robotic hands. The prediction is enforced using two sets of surface electromyography electrodes and an incremental, non-linear machine learning technique called Incremental Ridge Regression with Random Fourier Features. Nine able-bodied subjects were engaged in a functional test with the aim to evaluate the performance of the system. The robotic hands were mounted on two hand/wrist orthopedic splints worn by healthy subjects and controlled online. An average completion rate of more than 95% was achieved in single-handed tasks and 84% in bimanual tasks. On average, 5 min of retraining were necessary on a total session duration of about 1 h and 40 min. This work sets a beginning in the study of bimanual manipulation with prostheses and will be carried on through experiments in unilateral and bilateral upper limb amputees thus increasing its scientific value.

Hand hygiene using a new hand-cleansing formulation without sanitizers: Effect on Staphylococcus aureus removal and recovery of properties against skin damage.

PubMed

Asaoka, Kentaro; Endo, Shiro; Suzuki, Yuki; Komuro, Satoru; Nemoto, Tadanobu; Kaku, Mitsuo

2016-08-01

Staphylococcus aureus is known to form a biofilm and colonize on damaged skin of the hands. We investigated changes in the quantity of S aureus on the hands and changes in skin damage when using a hand-cleansing formulation with potassium oleate but without a sanitizer (formulation A), which is highly effective in removing S aureus biofilm and causes minimal skin damage. The participants (14 medical staff members) used 2 types of hand-cleansing formulations (formulations A and B), each for 4 weeks. S aureus of the hands was cultured from swab samples on agar plates. Surface of hands was measured using an ultraviolet light microscope. The quantity of S aureus after using formulation A for 4 weeks was 10(1.08 ± 0.05) CFU/mL, a statistically significant decrease from the quantity of S aureus (10(1.59 ± 0.19) CFU/mL) just before use (P = .029). Also, dryness of hand surfaces decreased. With formulation B, the quantity of S aureus did not significantly change from before to after use (P > .05). This presumably occurs because formulation A gently removes S aureus biofilm. Formulation A removed S aureus from the hands of participants, and skin damage on the hands improved. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Water management practices in rural and urban homes: a case study from Bangladesh on ingestion of polluted water.

PubMed

Ahmed, S A; Hoque, B A; Mahmud, A

1998-09-01

Although Bangladesh has achieved remarkable success in extending the availability of hand pumped and piped water, unsafe water is still ingested. This brief study attempted to assess water management practices in rural and urban homes in Bangladesh so as to establish the routes by which unsafe water is ingested, to examine methods of collection and storage, and determine why unsafe water sources are used when unsafe supplies are available. Forty-eight rural and forty-five urban slum households were studied. Observations, interviews and water quality investigations were conducted. The results show that the respondents were aware that hand pump/tap water is safe and took care to use these safe sources for drinking purposes. However, they continued to use surface water for non-drinking activities such as bathing, washing and rinsing their mouths. Reasons were given that it was a traditional practice to bathe in surface water and was more enjoyable. One of the reasons given for not using hand pumped water to wash clothing and food was that such groundwater caused staining. Bacteriological results from such ingested water showed the quality, especially in rural areas, to be poor. Results also showed the internal surfaces of the base of storage containers to be heavily contaminated with bacteria. This showed that water that was safe when it was first drawn would became contaminated during storage. This study had a limited scope; much further research is needed to find what determines and how water becomes contaminated in containers. These factors include how to reduce contamination of water, in particular the relationship between growth of bacteria in stored water and the material from which the container is made and how to improve the overall quality of water. On the management side, studies could be conducted as to how to improve people's understanding of the use of water for domestic purposes and its safe management.

An observational study of frequency of provider hand contacts in child care facilities in North Carolina and South Carolina.

PubMed

Fraser, Angela; Wohlgenant, Kelly; Cates, Sheryl; Chen, Xi; Jaykus, Lee-Ann; Li, You; Chapman, Benjamin

2015-02-01

Children enrolled in child care are 2.3-3.5 times more likely to experience acute gastrointestinal illness than children cared for in their own homes. The purpose of this study was to determine the frequency surfaces were touched by child care providers to identify surfaces that should be cleaned and sanitized. Observation data from a convenience sample of 37 child care facilities in North Carolina and South Carolina were analyzed. Trained data collectors used iPods (Apple, Cupertino, CA) to record hand touch events of 1 child care provider for 45 minutes in up to 2 classrooms in each facility. Across the 37 facilities, 10,134 hand contacts were observed in 51 classrooms. Most (4,536) were contacts with porous surfaces, with an average of 88.9 events per classroom observation. The most frequently touched porous surface was children's clothing. The most frequently touched nonporous surface was food contact surfaces (18.6 contacts/observation). Surfaces commonly identified as high-touch surfaces (ie, light switches, handrails, doorknobs) were touched the least. General cleaning and sanitizing guidelines should include detailed procedures for cleaning and sanitizing high-touch surfaces (ie, clothes, furniture, soft toys). Guidelines are available for nonporous surfaces but not for porous surfaces (eg, clothing, carpeting). Additional research is needed to inform the development of evidence-based practices to effectively treat porous surfaces. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

An ellipsoidal representation of human hand anthropometry

NASA Technical Reports Server (NTRS)

Buchholz, Bryan; Armstrong, Thomas J.

1991-01-01

Anthropometric data concerning the heometry of the hand's surface are presently modeled as a function of gross external hand measurements; an effort is made to evaluate the accuracy with which ellipsoids describe the geometry of the hand segments. Graphical comparisons indicate that differences between the ellipsoidal approximations and the breadth and depth measurements were greatest near the joints. On the bases of the present data, a set of overlapping ellipsoids could furnish a more accurate representation of hand geometry for adaptation to ellipsoid segment-geometry employing biomechanical models.

Divergent opinions on surface disinfection: myths or prevention? A review of the literature

PubMed Central

Exner, Martin

2007-01-01

Virtually no prevention strategy in hospital hygiene has been the focus of such frequent controversial discussions as the role of surface disinfection. Set against that background, the Commission for Hospital Hygiene and Infection Prevention at the Robert Koch Institute founded a working group comprising members with divergent views of risk evaluation as regards the role of disinfection. This working group produced a most carefully drafted guideline on how to deal with various risk areas and also incorporated a new provision into the guideline, stating that: “Cleaning and disinfection procedures must be organized and implemented such that there is no increase in the microbial load or spread of facultatively pathogenic or pathogenic microorganisms on surfaces.” Numerous studies have come to the conclusion that surface disinfection constitutes a basic infection control measure with which the spread of pathogens can be controlled. Conversely, when using only detergents such a form of control is not possible, something that must be taken into account in future when engaging in risk evaluation and formulating infection control measures. In view of the burgeoning trend in, for example, norovirus outbreaks, also in hospitals and nursing homes, such insights are of paramount importance and attest to the need for disinfection of surfaces and of areas with frequent hand and skin contacts. This discussion about the need for surface disinfection has, in addition to causing confusion among users, led to a decline in the willingness to accept hygienic practices, thus increasing the risk of occurrence of nosocomial infections as well as of antibiotic-resistant microorganisms. PMID:20200680

Divergent opinions on surface disinfection: myths or prevention? A review of the literature.

PubMed

Exner, Martin

2007-09-13

Virtually no prevention strategy in hospital hygiene has been the focus of such frequent controversial discussions as the role of surface disinfection. Set against that background, the Commission for Hospital Hygiene and Infection Prevention at the Robert Koch Institute founded a working group comprising members with divergent views of risk evaluation as regards the role of disinfection. This working group produced a most carefully drafted guideline on how to deal with various risk areas and also incorporated a new provision into the guideline, stating that: "Cleaning and disinfection procedures must be organized and implemented such that there is no increase in the microbial load or spread of facultatively pathogenic or pathogenic microorganisms on surfaces."Numerous studies have come to the conclusion that surface disinfection constitutes a basic infection control measure with which the spread of pathogens can be controlled. Conversely, when using only detergents such a form of control is not possible, something that must be taken into account in future when engaging in risk evaluation and formulating infection control measures. In view of the burgeoning trend in, for example, norovirus outbreaks, also in hospitals and nursing homes, such insights are of paramount importance and attest to the need for disinfection of surfaces and of areas with frequent hand and skin contacts. This discussion about the need for surface disinfection has, in addition to causing confusion among users, led to a decline in the willingness to accept hygienic practices, thus increasing the risk of occurrence of nosocomial infections as well as of antibiotic-resistant microorganisms.

Body mass modulates huddling dynamics and body temperature profiles in rabbit pups.

PubMed

Bautista, Amando; Zepeda, José Alfredo; Reyes-Meza, Verónica; Féron, Christophe; Rödel, Heiko G; Hudson, Robyn

2017-10-01

Altricial mammals typically lack the physiological capacity to thermoregulate independently during the early postnatal period, and in litter-bearing species the young benefit strongly from huddling together with their litter siblings. Such litter huddles are highly dynamic systems, often characterized by competition for energetically favorable, central positions. In the present study, carried out in domestic rabbits Oryctolagus cuniculus, we asked whether individual differences in body mass affect changes in body temperature during changes in the position within the huddle. We predicted that pups with relatively lower body mass should be more affected by such changes arising from huddle dynamics in comparison to heavier ones. Changes in pups' maximum body surface temperature (determined by infrared thermography) were significantly affected by changes in the number of their neighbors in the litter huddle, and indeed these temperature changes largely depended on the pups' body mass relative to their litter siblings. Lighter pups showed significant increases in their maximum body surface temperature when their number of huddling partners increased by one or two siblings whereas pups with intermediate or heavier body mass did not show such significant increases in maximum body temperature when experiencing such changes. A similar pattern was found with respect to average body surface temperature. This strong link between changes in the number of huddling partners and body surface temperature in lighter pups might, on the one hand, arise from a higher vulnerability of such pups due to their less favorable body surface area-to-volume ratio. On the other hand, as lighter pups generally had fewer neighbors than heavier ones and thus typically a comparatively smaller body surface in contact with siblings, they potentially had more to gain from increasing their number of neighbors. The present findings might help to understand how individual differences in body mass within a litter lead to the emergence of individual differences in sibling interactions during early postnatal life in different species of altricial and litter-bearing mammals. Copyright © 2017 Elsevier Inc. All rights reserved.

Automatic 3D Extraction of Buildings, Vegetation and Roads from LIDAR Data

NASA Astrophysics Data System (ADS)

Bellakaout, A.; Cherkaoui, M.; Ettarid, M.; Touzani, A.

2016-06-01

Aerial topographic surveys using Light Detection and Ranging (LiDAR) technology collect dense and accurate information from the surface or terrain; it is becoming one of the important tools in the geosciences for studying objects and earth surface. Classification of Lidar data for extracting ground, vegetation, and buildings is a very important step needed in numerous applications such as 3D city modelling, extraction of different derived data for geographical information systems (GIS), mapping, navigation, etc... Regardless of what the scan data will be used for, an automatic process is greatly required to handle the large amount of data collected because the manual process is time consuming and very expensive. This paper is presenting an approach for automatic classification of aerial Lidar data into five groups of items: buildings, trees, roads, linear object and soil using single return Lidar and processing the point cloud without generating DEM. Topological relationship and height variation analysis is adopted to segment, preliminary, the entire point cloud preliminarily into upper and lower contours, uniform and non-uniform surface, non-uniform surfaces, linear objects, and others. This primary classification is used on the one hand to know the upper and lower part of each building in an urban scene, needed to model buildings façades; and on the other hand to extract point cloud of uniform surfaces which contain roofs, roads and ground used in the second phase of classification. A second algorithm is developed to segment the uniform surface into buildings roofs, roads and ground, the second phase of classification based on the topological relationship and height variation analysis, The proposed approach has been tested using two areas : the first is a housing complex and the second is a primary school. The proposed approach led to successful classification results of buildings, vegetation and road classes.

46 CFR 154.1155 - Hand hose line: Coverage.

Code of Federal Regulations, 2010 CFR

2010-10-01

... STANDARDS FOR SELF-PROPELLED VESSELS CARRYING BULK LIQUEFIED GASES Design, Construction and Equipment Firefighting System: Dry Chemical § 154.1155 Hand hose line: Coverage. The coverage for the area for a hand...

Quantifying muscle patterns and spine load during various forms of the push-up.

PubMed

Freeman, Stephanie; Karpowicz, Amy; Gray, John; McGill, Stuart

2006-03-01

This study was conducted to quantify the normalized amplitudes of the abdominal wall and back extensor musculature during a variety of push-up styles. We also sought to quantify their impact on spinal loading by calculating spinal compression and torque generation in the L4-5 area. Ten university-age participants, nine males and one female, in good to excellent condition, volunteered to participate in this study. All participants were requested to perform a maximum of 12 different push-up exercises, three trials per exercise. Surface electromyographic data (EMG) were collected bilaterally on rectus abdominis, external oblique, internal oblique, latissimus dorsi, and erector spinae muscles, and unilaterally (right side) on pectoralis major, triceps brachii, biceps brachii, and anterior deltoid muscles. Spine kinetics were obtained using an anatomically detailed model of the torso/spine. This study revealed that more dynamic push-ups (i.e., ballistic, with hand movement) required more muscle activation and higher spine load, whereas placing labile balls under the hands only resulted in modest increases in spine load. Right rectus abdominis (RA) activation was significantly higher than left RA activation during the left hand forward push-up and vice versa for the right hand forward push-up (P < 0.001). External oblique (EO) demonstrated the same switch in dominance during staggered hand push-ups (P < 0.01). The one-arm push-up resulted in the highest spine compression. Skilled participants showed greater synchronicity with peak muscle activation (plyometric type of contractions) during ballistic push-ups. These data will help guide exercise selection for individuals with differing training objectives and injury history.

Distribution of peanut allergen in the environment.

PubMed

Perry, Tamara T; Conover-Walker, Mary Kay; Pomés, Anna; Chapman, Martin D; Wood, Robert A

2004-05-01

Patients with peanut allergy can have serious reactions to very small quantities of peanut allergen and often go to extreme measures to avoid potential contact with this allergen. The purpose of this study was to detect peanut allergen under various environmental conditions and examine the effectiveness of cleaning agents for allergen removal. A monoclonal-based ELISA for Arachis hypogaea allergen 1 (Ara h 1; range of detection, 30-2000 ng/mL) was used to assess peanut contamination on cafeteria tables and other surfaces in schools, the presence of residual peanut protein after using various cleaning products on hands and tabletops, and airborne peanut allergen during the consumption of several forms of peanut. After hand washing with liquid soap, bar soap, or commercial wipes, Ara h 1 was undetectable. Plain water and antibacterial hand sanitizer left detectable Ara h 1 on 3 of 12 and 6 of 12 hands, respectively. Common household cleaning agents removed peanut allergen from tabletops, except dishwashing liquid, which left Ara h 1 on 4 of 12 tables. Of the 6 area preschools and schools evaluated, Ara h 1 was found on 1 of 13 water fountains, 0 of 22 desks, and 0 of 36 cafeteria tables. Airborne Ara h 1 was undetectable in simulated real-life situations when participants consumed peanut butter, shelled peanuts, and unshelled peanuts. The major peanut allergen, Ara h 1, is relatively easily cleaned from hands and tabletops with common cleaning agents and does not appear to be widely distributed in preschools and schools. We were not able to detect airborne allergen in many simulated environments.

Quadro-pulse stimulation is more effective than paired-pulse stimulation for plasticity induction of the human motor cortex.

PubMed

Hamada, Masashi; Hanajima, Ritsuko; Terao, Yasuo; Arai, Noritoshi; Furubayashi, Toshiaki; Inomata-Terada, Satomi; Yugeta, Akihiro; Matsumoto, Hideyuki; Shirota, Yuichiro; Ugawa, Yoshikazu

2007-12-01

Repetitive paired-pulse transcranial magnetic stimulation (TMS) at I-wave periodicity has been shown to induce a motor-evoked potential (MEP) facilitation. We hypothesized that a greater enhancement of motor cortical excitability is provoked by increasing the number of pulses per train beyond those by paired-pulse stimulation (PPS). We explored motor cortical excitability changes induced by repetitive application of trains of four monophasic magnetic pulses (quadro-pulse stimulation: QPS) at 1.5-ms intervals, repeated every 5s over the motor cortex projecting to the hand muscles. The aftereffects of QPS were evaluated with MEPs to a single-pulse TMS, motor threshold (MT), and responses to brain-stem stimulation. These effects were compared to those after PPS. To evaluate the QPS safety, we also studied the spread of excitation and after discharge using surface electromyograms (EMGs) of hand and arm muscles. Sizes of MEPs from the hand muscle were enhanced for longer than 75min after QPS; they reverted to the baseline at 90min. Responses to brain-stem stimulation from the hand muscle and cortical MEPs from the forearm muscle were unchanged after QPS over the hand motor area. MT was unaffected by QPS. No spreads of excitation were detected after QPS. The appearance rate of after discharges during QPS was not different from that during sham stimulation. Results show that QPS can safely induce long-lasting, topographically specific enhancement of motor cortical excitability. QPS is more effective than PPS for inducing motor cortical plasticity.

Quantitative biological surface science: challenges and recent advances.

PubMed

Höök, Fredrik; Kasemo, Bengt; Grunze, Michael; Zauscher, Stefan

2008-12-23

Biological surface science is a broad, interdisciplinary subfield of surface science, where properties and processes at biological and synthetic surfaces and interfaces are investigated, and where biofunctional surfaces are fabricated. The need to study and to understand biological surfaces and interfaces in liquid environments provides sizable challenges as well as fascinating opportunities. Here, we report on recent progress in biological surface science that was described within the program assembled by the Biomaterial Interface Division of the Science and Technology of Materials, Interfaces and Processes (www.avs.org) during their 55th International Symposium and Exhibition held in Boston, October 19-24, 2008. The selected examples show that the rapid progress in nanoscience and nanotechnology, hand-in-hand with theory and simulation, provides increasingly sophisticated methods and tools to unravel the mechanisms and details of complex processes at biological surfaces and in-depth understanding of biomolecular surface interactions.

Land Use and Land Cover (LULC) Change Detection in Islamabad and its Comparison with Capital Development Authority (CDA) 2006 Master Plan

NASA Astrophysics Data System (ADS)

Hasaan, Zahra

2016-07-01

Remote sensing is very useful for the production of land use and land cover statistics which can be beneficial to determine the distribution of land uses. Using remote sensing techniques to develop land use classification mapping is a convenient and detailed way to improve the selection of areas designed to agricultural, urban and/or industrial areas of a region. In Islamabad city and surrounding the land use has been changing, every day new developments (urban, industrial, commercial and agricultural) are emerging leading to decrease in vegetation cover. The purpose of this work was to develop the land use of Islamabad and its surrounding area that is an important natural resource. For this work the eCognition Developer 64 computer software was used to develop a land use classification using SPOT 5 image of year 2012. For image processing object-based classification technique was used and important land use features i.e. Vegetation cover, barren land, impervious surface, built up area and water bodies were extracted on the basis of object variation and compared the results with the CDA Master Plan. The great increase was found in built-up area and impervious surface area. On the other hand vegetation cover and barren area followed a declining trend. Accuracy assessment of classification yielded 92% accuracies of the final land cover land use maps. In addition these improved land cover/land use maps which are produced by remote sensing technique of class definition, meet the growing need of legend standardization.

Groundwater source contamination mechanisms: Physicochemical profile clustering, risk factor analysis and multivariate modelling

NASA Astrophysics Data System (ADS)

Hynds, Paul; Misstear, Bruce D.; Gill, Laurence W.; Murphy, Heather M.

2014-04-01

An integrated domestic well sampling and "susceptibility assessment" programme was undertaken in the Republic of Ireland from April 2008 to November 2010. Overall, 211 domestic wells were sampled, assessed and collated with local climate data. Based upon groundwater physicochemical profile, three clusters have been identified and characterised by source type (borehole or hand-dug well) and local geological setting. Statistical analysis indicates that cluster membership is significantly associated with the prevalence of bacteria (p = 0.001), with mean Escherichia coli presence within clusters ranging from 15.4% (Cluster-1) to 47.6% (Cluster-3). Bivariate risk factor analysis shows that on-site septic tank presence was the only risk factor significantly associated (p < 0.05) with bacterial presence within all clusters. Point agriculture adjacency was significantly associated with both borehole-related clusters. Well design criteria were associated with hand-dug wells and boreholes in areas characterised by high permeability subsoils, while local geological setting was significant for hand-dug wells and boreholes in areas dominated by low/moderate permeability subsoils. Multivariate susceptibility models were developed for all clusters, with predictive accuracies of 84% (Cluster-1) to 91% (Cluster-2) achieved. Septic tank setback was a common variable within all multivariate models, while agricultural sources were also significant, albeit to a lesser degree. Furthermore, well liner clearance was a significant factor in all models, indicating that direct surface ingress is a significant well contamination mechanism. Identification and elucidation of cluster-specific contamination mechanisms may be used to develop improved overall risk management and wellhead protection strategies, while also informing future remediation and maintenance efforts.

Transcranial direct current stimulation to primary motor area improves hand dexterity and selective attention in chronic stroke.

PubMed

Au-Yeung, Stephanie S Y; Wang, Juliana; Chen, Ye; Chua, Eldrich

2014-12-01

The aim of this study was to determine whether transcranial direct current stimulation (tDCS) applied to the primary motor hand area modulates hand dexterity and selective attention after stroke. This study was a double-blind, placebo-controlled, randomized crossover trial involving subjects with chronic stroke. Ten stroke survivors with some pinch strength in the paretic hand received three different tDCS interventions assigned in random order in separate sessions-anodal tDCS targeting the primary motor area of the lesioned hemisphere (M1lesioned), cathodal tDCS applied to the contralateral hemisphere (M1nonlesioned), and sham tDCS-each for 20 mins. The primary outcome measures were Purdue pegboard test scores for hand dexterity and response time in the color-word Stroop test for selective attention. Pinch strength of the paretic hand was the secondary outcome. Cathodal tDCS to M1nonlesioned significantly improved affected hand dexterity (by 1.1 points on the Purdue pegboard unimanual test, P = 0.014) and selective attention (0.6 secs faster response time on the level 3 Stroop interference test for response inhibition, P = 0.017), but not pinch strength. The outcomes were not improved with anodal tDCS to M1lesioned or sham tDCS. Twenty minutes of cathodal tDCS to M1nonlesioned can promote both paretic hand dexterity and selective attention in people with chronic stroke.

Comparison of the impact of scaler material composition on polished titanium implant abutment surfaces.

PubMed

Hasturk, Hatice; Nguyen, Daniel Huy; Sherzai, Homa; Song, Xiaoping; Soukos, Nikos; Bidlack, Felicitas B; Van Dyke, Thomas E

2013-08-01

The purpose of this study was to compare the impact of the removal of biofilm with hand scalers of different material composition on the surface of implant abutments by assessing the surface topography and residual plaque after scaling using scanning electron microscopy (SEM). Titanium implant analogs from 3 manufacturers (Straumann USA LLC, Andover, Maine, Nobel BioCare USA LLC, Yorba Linda, Cali, Astra Tech Implant Systems, Dentsply, Mölndal, Sweden) were mounted in stone in plastic vials individually with authentic prosthetic abutments. Plaque samples were collected from a healthy volunteer, inoculated into growth medium and incubated with the abutments anaerobically for 1 week. A blinded, calibrated hygienist performed scaling to remove the biofilm using 6 implant scalers (in triplicate), 1 scaler for 1 abutment. The abutments were mounted on an imaging stand and processed for SEM. Images were captured in 3 randomly designated areas of interest on each abutment. Analysis of the implant polished abutment surface and plaque area measurements were performed using ImageJ image analysis software. Surface alterations were characterized by the number, length, depth and the width of the scratches observed. Glass filled resin scalers resulted in significantly more and longer scratches on all 3 abutment types compared to other scalers, while unfilled resin scalers resulted in the least surface change (p < 0.05). Filled resin-graphite reinforced scalers, carbon fiber reinforced resin scalers and titanium scalers resulted in more superficial scratches compared to glass filled resin, as well as more scratches than unfilled resin. No statistically significant differences were found between scalers and abutments with regard to plaque removal. The impact of scalers on implant abutment surfaces varies between abutment types presumably due to different surface characteristics with no apparent advantage of one abutment type over the other with regard to resistance to surface damage. Unfilled resin was found consistently to be the least damaging to abutment surfaces, although all scalers of all compositions caused detectable surface changes to polished surfaces of implant abutments.

Determination of Pesticide Dermal Transfer to Operators & Agricultural Workers through Contact with Sprayed Hard Surfaces.

PubMed

Tsakirakis, Angelos N; Kasiotis, Konstantinos M; Anastasiadou, Pelagia; Charistou, Agathi N; Gerritsen-Ebben, Rianda; Glass, C Richard; Machera, Kyriaki

2018-05-20

In the present study, the dermal transfer rate of pesticides to agricultural workers occurring via contact with sprayed hard surfaces was investigated. Cotton gloves were used as dosimeters to collect residues from hard surfaces contaminated by pesticides in greenhouses. Dosimeters, either dry or moistened, were in contact with wood, metal and plastic surfaces previously sprayed. The experimental approach applied mimicked the typical hand contact. Moistened cotton gloves were used to simulate hand moisture from dew/condensation or rainfall. The effect of total duration of contact on the final hand exposure via transfer was investigated. The higher duration contact tested (50-sec) resulted in the higher transfer rates for metal and plastic surfaces; no such effect was noted in case of the wood surface. The pesticide amount transferred from the metal and plastic surfaces to wet gloves was greater than the one transferred to dry gloves. Such trend was not observed for the wood surface. Transfer rates varied from 0.46-77.62% and 0.17-16.90% for wet and dry samples, respectively. The current study has generated new data to quantify the proportion of pesticide deposits dislodged from three different non-crop surfaces when in contact with dry or wet gloves. This article is protected by copyright. All rights reserved. This article is protected by copyright. All rights reserved.

Runoff of acidic substances that originated from atmospheric deposition on Yakushima Island, a world natural heritage site.

PubMed

Nagafuchi, O; Kakimoto, H; Ebise, S; Inoue, T; Koga, M

2001-01-01

In this paper we present monitoring data of stream waters that may reflect acidic impacts on the island as well as the rainwater qualities. The pH ranges of the river water in the Kawara streams in the western part of the island and the Yodogo stream in the central part of the island were 5.71-6.35 and 5.85-6.12 during 1992-1999, respectively. The concentrations of SO4(2-) and NO3- in the river water were lower than those in the rainwater. Many differences were observed among the sampling sites. Higher concentrations of acid substances are found in the stream waters of the western area compared to the other areas. On the other hand, sulfuric acid is the major acid in the rainwater, snow and rime ice. No differences were observed in the ion constituents of the rainwater collected in the areas. These results suggested that the densely growing canopy may play a role in holding air pollutants, and acidic substances deposited on the canopy would be discharged as a through-fall and a stem flow. Furthermore, the water mass containing high ionic substances in the western area has been held in the groundwater layer, continuously supplying the stream waters during dry weather days. On the other hand, part of the basic runoff will be diluted with a surface runoff during the rainy days. As a result, the concentrations of the ionic substances in the stream waters during rainy days decreased.

Vertical Distribution and Estimated Doses from Artificial Radionuclides in Soil Samples around the Chernobyl Nuclear Power Plant and the Semipalatinsk Nuclear Testing Site

PubMed Central

Taira, Yasuyuki; Hayashida, Naomi; Tsuchiya, Rimi; Yamaguchi, Hitoshi; Takahashi, Jumpei; Kazlovsky, Alexander; Urazalin, Marat; Rakhypbekov, Tolebay; Yamashita, Shunichi; Takamura, Noboru

2013-01-01

For the current on-site evaluation of the environmental contamination and contributory external exposure after the accident at the Chernobyl Nuclear Power Plant (CNPP) and the nuclear tests at the Semipalatinsk Nuclear Testing Site (SNTS), the concentrations of artificial radionuclides in soil samples from each area were analyzed by gamma spectrometry. Four artificial radionuclides (241Am, 134Cs, 137Cs, and 60Co) were detected in surface soil around CNPP, whereas seven artificial radionuclides (241Am, 57Co, 137Cs, 95Zr, 95Nb, 58Co, and 60Co) were detected in surface soil around SNTS. Effective doses around CNPP were over the public dose limit of 1 mSv/y (International Commission on Radiological Protection, 1991). These levels in a contaminated area 12 km from Unit 4 were high, whereas levels in a decontaminated area 12 km from Unit 4 and another contaminated area 15 km from Unit 4 were comparatively low. On the other hand, the effective doses around SNTS were below the public dose limit. These findings suggest that the environmental contamination and effective doses on the ground definitely decrease with decontamination such as removing surface soil, although the effective doses of the sampling points around CNPP in the present study were all over the public dose limit. Thus, the remediation of soil as a countermeasure could be an extremely effective method not only for areas around CNPP and SNTS but also for areas around the Fukushima Dai-ichi Nuclear Power Plant (FNPP), and external exposure levels will be certainly reduced. Long-term follow-up of environmental monitoring around CNPP, SNTS, and FNPP, as well as evaluation of the health effects in the population residing around these areas, could contribute to radiation safety and reduce unnecessary exposure to the public. PMID:23469013

Vertical distribution and estimated doses from artificial radionuclides in soil samples around the Chernobyl nuclear power plant and the Semipalatinsk nuclear testing site.

PubMed

Taira, Yasuyuki; Hayashida, Naomi; Tsuchiya, Rimi; Yamaguchi, Hitoshi; Takahashi, Jumpei; Kazlovsky, Alexander; Urazalin, Marat; Rakhypbekov, Tolebay; Yamashita, Shunichi; Takamura, Noboru

2013-01-01

For the current on-site evaluation of the environmental contamination and contributory external exposure after the accident at the Chernobyl Nuclear Power Plant (CNPP) and the nuclear tests at the Semipalatinsk Nuclear Testing Site (SNTS), the concentrations of artificial radionuclides in soil samples from each area were analyzed by gamma spectrometry. Four artificial radionuclides ((241)Am, (134)Cs, (137)Cs, and (60)Co) were detected in surface soil around CNPP, whereas seven artificial radionuclides ((241)Am, (57)Co, (137)Cs, (95)Zr, (95)Nb, (58)Co, and (60)Co) were detected in surface soil around SNTS. Effective doses around CNPP were over the public dose limit of 1 mSv/y (International Commission on Radiological Protection, 1991). These levels in a contaminated area 12 km from Unit 4 were high, whereas levels in a decontaminated area 12 km from Unit 4 and another contaminated area 15 km from Unit 4 were comparatively low. On the other hand, the effective doses around SNTS were below the public dose limit. These findings suggest that the environmental contamination and effective doses on the ground definitely decrease with decontamination such as removing surface soil, although the effective doses of the sampling points around CNPP in the present study were all over the public dose limit. Thus, the remediation of soil as a countermeasure could be an extremely effective method not only for areas around CNPP and SNTS but also for areas around the Fukushima Dai-ichi Nuclear Power Plant (FNPP), and external exposure levels will be certainly reduced. Long-term follow-up of environmental monitoring around CNPP, SNTS, and FNPP, as well as evaluation of the health effects in the population residing around these areas, could contribute to radiation safety and reduce unnecessary exposure to the public.

Registration-based segmentation with articulated model from multipostural magnetic resonance images for hand bone motion animation.

PubMed

Chen, Hsin-Chen; Jou, I-Ming; Wang, Chien-Kuo; Su, Fong-Chin; Sun, Yung-Nien

2010-06-01

The quantitative measurements of hand bones, including volume, surface, orientation, and position are essential in investigating hand kinematics. Moreover, within the measurement stage, bone segmentation is the most important step due to its certain influences on measuring accuracy. Since hand bones are small and tubular in shape, magnetic resonance (MR) imaging is prone to artifacts such as nonuniform intensity and fuzzy boundaries. Thus, greater detail is required for improving segmentation accuracy. The authors then propose using a novel registration-based method on an articulated hand model to segment hand bones from multipostural MR images. The proposed method consists of the model construction and registration-based segmentation stages. Given a reference postural image, the first stage requires construction of a drivable reference model characterized by hand bone shapes, intensity patterns, and articulated joint mechanism. By applying the reference model to the second stage, the authors initially design a model-based registration pursuant to intensity distribution similarity, MR bone intensity properties, and constraints of model geometry to align the reference model to target bone regions of the given postural image. The authors then refine the resulting surface to improve the superimposition between the registered reference model and target bone boundaries. For each subject, given a reference postural image, the proposed method can automatically segment all hand bones from all other postural images. Compared to the ground truth from two experts, the resulting surface image had an average margin of error within 1 mm (mm) only. In addition, the proposed method showed good agreement on the overlap of bone segmentations by dice similarity coefficient and also demonstrated better segmentation results than conventional methods. The proposed registration-based segmentation method can successfully overcome drawbacks caused by inherent artifacts in MR images and obtain more accurate segmentation results automatically. Moreover, realistic hand motion animations can be generated based on the bone segmentation results. The proposed method is found helpful for understanding hand bone geometries in dynamic postures that can be used in simulating 3D hand motion through multipostural MR images.

Observation of public health risk behaviours, risk communication and hand hygiene at Kansas and Missouri petting zoos--2010-2011.

PubMed

Erdozain, G; KuKanich, K; Chapman, B; Powell, D

2013-06-01

Outbreaks of human illness have been linked to visiting settings with animal contact throughout developed countries. This study details an observational study of hand hygiene tool availability and recommendations; frequency of risky behaviour; and handwashing attempts by visitors in Kansas (9) and Missouri (4), USA, petting zoos. Handwashing signs and hand hygiene stations were available at the exit of animal-contact areas in 10/13 and 8/13 petting zoos, respectively. Risky behaviours were observed being performed at all petting zoos by at least one visitor. Frequently observed behaviours were as follows: children (10/13 petting zoos) and adults (9/13 petting zoos) touching hands to face within animal-contact areas; animals licking children's and adults' hands (7/13 and 4/13 petting zoos, respectively); and children and adults drinking within animal-contact areas (5/13 petting zoos each). Of 574 visitors observed for hand hygiene when exiting animal-contact areas, 37% (n = 214) of individuals attempted some type of hand hygiene, with male adults, female adults and children attempting at similar rates (32%, 40% and 37%, respectively). Visitors were 4.8× more likely to wash their hands when a staff member was present within or at the exit to the animal-contact area (136/231, 59%) than when no staff member was present (78/343, 23%; P < 0.001, OR = 4.863, 95% CI = 3.380-6.998). Visitors at zoos with a fence as a partial barrier to human-animal contact were 2.3× more likely to wash their hands (188/460, 40.9%) than visitors allowed to enter the animals' yard for contact (26/114, 22.8%; P < 0.001, OR = 2.339, 95% CI = 1.454-3.763). Inconsistencies existed in tool availability, signage and supervision of animal contact. Risk communication was poor, with few petting zoos outlining risks associated with animal contact, or providing recommendations for precautions to be taken to reduce these risks. © 2012 Blackwell Verlag GmbH.

Contamination of public buses with MRSA in Lisbon, Portugal: a possible transmission route of major MRSA clones within the community.

PubMed

Conceição, Teresa; Diamantino, Fernanda; Coelho, Céline; de Lencastre, Hermínia; Aires-de-Sousa, Marta

2013-01-01

In a previous study we have shown that public buses in Oporto, the second largest city in Portugal, were highly contaminated with MRSA. Here we describe the results of a similar study performed in another urban area of Portugal-Lisbon, the capital. Between May 2011 and May 2012, hand touched surfaces of 199 public buses in Lisbon were screened for MRSA contamination. Subsequently, the hands of 575 passengers who frequently use these bus lines were also screened. All hand carriers of MRSA were further screened for nasal carriage. The isolates were characterized by PFGE, staphylococcal cassette chromosome (SCC) mec typing, spa typing, MLST and were tested for the presence of mecA, Panton-Valentine leukocidin and arginine catabolic mobile element genes. MRSA contamination was shown in 72 buses (36.2%). The majority of the isolates belonged to three major clones: Clone A was identified as EMRSA-15 defined by pattern PFGE A, spa types t2357/t747/t025/t379/t910, ST22, and SCCmec IVh (n = 21; 29%). Clone B was the New York/Japan clone characterized by PFGE B-t002/t10682-ST5-II (n = 15; 21%). Clone C included isolates with characteristics of the international community-acquired USA300 or related clones, PFGE C-t008-ST8-IVa/IVc/IVg/IVnt/VI (n = 19; 26%). The first two clones are currently the two major lineages circulating in Portuguese hospitals. The hands of 15 individuals were contaminated with MRSA belonging to the nosocomial clones A or B. Eleven of these individuals were not nasal carriers of MRSA and all but one had travelled by public transportation, namely by bus, prior to sampling. In conclusion, public buses in two major cities in Portugal are often contaminated with MRSA representing clones dominant in hospitals in the particular geographic area. MRSA contamination of public transport and the transfer of the bacteria to the hands of passengers may represent a route through which hospital-acquired MRSA clones may spread to the community.

Microsphere integrated microfluidic disk: synergy of two techniques for rapid and ultrasensitive dengue detection

PubMed Central

Hosseini, Samira; Aeinehvand, Mohammad M.; Uddin, Shah M.; Benzina, Abderazak; Rothan, Hussin A.; Yusof, Rohana; Koole, Leo H.; Madou, Marc J.; Djordjevic, Ivan; Ibrahim, Fatimah

2015-01-01

The application of microfluidic devices in diagnostic systems is well-established in contemporary research. Large specific surface area of microspheres, on the other hand, has secured an important position for their use in bioanalytical assays. Herein, we report a combination of microspheres and microfluidic disk in a unique hybrid platform for highly sensitive and selective detection of dengue virus. Surface engineered polymethacrylate microspheres with carefully designed functional groups facilitate biorecognition in a multitude manner. In order to maximize the utility of the microspheres’ specific surface area in biomolecular interaction, the microfluidic disk was equipped with a micromixing system. The mixing mechanism (microballoon mixing) enhances the number of molecular encounters between spheres and target analyte by accessing the entire sample volume more effectively, which subsequently results in signal amplification. Significant reduction of incubation time along with considerable lower detection limits were the prime motivations for the integration of microspheres inside the microfluidic disk. Lengthy incubations of routine analytical assays were reduced from 2 hours to 5 minutes while developed system successfully detected a few units of dengue virus. Obtained results make this hybrid microsphere-microfluidic approach to dengue detection a promising avenue for early detection of this fatal illness. PMID:26548806

Assesing Geographic Isolation of the Galapagos Islands

NASA Astrophysics Data System (ADS)

Orellana, D.; Smith, F.

2016-06-01

The Galapagos Archipelago is one of the most important ecological spots in the planet due its unique biodiversity, active geology, and relatively well-preserved ecosystems. These characteristics are strongly based on the geographical isolation of the islands. On the one hand this isolation allowed the evolution processes that gave the islands their international fame and on the other hand it kept them from major human impacts that affected the vast majority of the Earth's surface. Galapagos' geographical isolation is therefore of mayor value, but it is rapidly diminishing due to the increase of marine and air transportation among islands and with the rest of the world. This increased accessibility implies enhanced risks for the ecological dynamics on the archipelago (e.g. increased risk of biological invasions, uncontrolled tourism growth, more water and energy consumption). Here, we introduce a general accessibility model to assess geographical isolation of the Galapagos Islands. The model aims to characterize accessibility in terms of human mobility by evaluating travel time to each point of the archipelago using all available transportation modalities. Using a multi criteria cost surface for marine and land areas, we estimated travel time for each surface unit using the fastest route and mode of transportation available while considering several friction factors such as surface type, slope, infrastructure, transfer points, legal restrictions, and physical barriers. We created maps to evaluate the isolation of different islands and places, highlighting the potential risks for several habitats and ecosystems. The model can be used for research and decision-making regarding island conservation, such as estimating spreading paths for invasive species, informing decisions on tourism management, and monitoring isolation changes of sensitive ecosystems.

Brain activation associated with practiced left hand mirror writing.

PubMed

Kushnir, T; Arzouan, Y; Karni, A; Manor, D

2013-04-01

Mirror writing occurs in healthy children, in various pathologies and occasionally in healthy adults. There are only scant experimental data on the underlying brain processes. Eight, right-handed, healthy young adults were scanned (BOLD-fMRI) before and after practicing left-hand mirror-writing (lh-MW) over seven sessions. They wrote dictated words, using either the right hand with regularly oriented writing or lh-MW. An MRI compatible stylus-point recording system was used and online visual feedback was provided. Practice resulted in increased speed and readability of lh-MW but the number of movement segments was unchanged. Post-training signal increases occurred in visual, right lateral and medial premotor areas, and in right anterior and posterior peri-sylvian areas corresponding to language areas. These results suggest that lh-MW may constitute a latent ability that can be reinstated by a relatively brief practice experience. Concurrently, right hemisphere language processing areas may emerge, reflecting perhaps a reduction in trans-hemispheric suppression. Copyright © 2013 Elsevier Inc. All rights reserved.

Trend Assessment of Spatio-Temporal Change of Tehran Heat Island Using Satellite Images

NASA Astrophysics Data System (ADS)

Saradjian, M. R.; Sherafati, Sh.

2015-12-01

Numerous investigations on Urban Heat Island (UHI) show that land cover change is the main factor of increasing Land Surface Temperature (LST) in urban areas, especially conversion of vegetation and bare soil to concrete, asphalt and other man-made structures. On the other hand, other human activities like those which cause to burning fossil fuels, that increase the amount of carbon dioxide, may raise temperature in global scale in comparison with small scales (urban areas). In this study, multiple satellite images with different spatial and temporal resolutions have been used to determine Land Surface Temperature (LST) variability in Tehran metropolitan area. High temporal resolution of AVHRR images have been used as the main data source when investigating temperature variability in the urban area. The analysis shows that UHI appears more significant at afternoon and night hours. But the urban class temperature is almost equal to its surrounding vegetation and bare soil classes at around noon. It also reveals that there is no specific difference in UHI intense during the days throughout the year. However, it can be concluded that in the process of city expansion in years, UHI has been grown both spatially and in magnitude. In order to locate land-cover types and relate them to LST, Thematic Mapper (TM) images have been exploited. The influence of elevation on the LST has also been studied, using digital elevation model derived from SRTM database.

Intramanual and intermanual transfer of the curvature aftereffect

PubMed Central

Duijndam, Maarten J. A.; Ketels, Myrna F. M.; Wilbers, Martine T. J. M.; Zwijsen, Sandra A.; Kappers, Astrid M. L.

2008-01-01

The existence and transfer of a haptic curvature aftereffect was investigated to obtain a greater insight into neural representation of shape. The haptic curvature aftereffect is the phenomenon whereby a flat surface is judged concave if the preceding touched stimulus was convex and vice versa. Single fingers were used to touch the subsequently presented stimuli. A substantial aftereffect was found when the adaptation surface and the test surface were touched by the same finger. Furthermore, a partial, but significant transfer of the aftereffect was demonstrated between fingers of the same hand and between fingers of both the hands. These results provide evidence that curvature information is not only represented at a level that is directly connected to the mechanoreceptors of individual fingers but is also represented at a stage in the somatosensory cortex shared by the fingers of both the hands. PMID:18438649

Dissociable neural responses to hands and non-hand body parts in human left extrastriate visual cortex.

PubMed

Bracci, Stefania; Ietswaart, Magdalena; Peelen, Marius V; Cavina-Pratesi, Cristiana

2010-06-01

Accumulating evidence points to a map of visual regions encoding specific categories of objects. For example, a region in the human extrastriate visual cortex, the extrastriate body area (EBA), has been implicated in the visual processing of bodies and body parts. Although in the monkey, neurons selective for hands have been reported, in humans it is unclear whether areas selective for individual body parts such as the hand exist. Here, we conducted two functional MRI experiments to test for hand-preferring responses in the human extrastriate visual cortex. We found evidence for a hand-preferring region in left lateral occipitotemporal cortex in all 14 participants. This region, located in the lateral occipital sulcus, partially overlapped with left EBA, but could be functionally and anatomically dissociated from it. In experiment 2, we further investigated the functional profile of hand- and body-preferring regions by measuring responses to hands, fingers, feet, assorted body parts (arms, legs, torsos), and non-biological handlike stimuli such as robotic hands. The hand-preferring region responded most strongly to hands, followed by robotic hands, fingers, and feet, whereas its response to assorted body parts did not significantly differ from baseline. By contrast, EBA responded most strongly to body parts, followed by hands and feet, and did not significantly respond to robotic hands or fingers. Together, these results provide evidence for a representation of the hand in extrastriate visual cortex that is distinct from the representation of other body parts.

Dissociable Neural Responses to Hands and Non-Hand Body Parts in Human Left Extrastriate Visual Cortex

PubMed Central

Ietswaart, Magdalena; Peelen, Marius V.; Cavina-Pratesi, Cristiana

2010-01-01

Accumulating evidence points to a map of visual regions encoding specific categories of objects. For example, a region in the human extrastriate visual cortex, the extrastriate body area (EBA), has been implicated in the visual processing of bodies and body parts. Although in the monkey, neurons selective for hands have been reported, in humans it is unclear whether areas selective for individual body parts such as the hand exist. Here, we conducted two functional MRI experiments to test for hand-preferring responses in the human extrastriate visual cortex. We found evidence for a hand-preferring region in left lateral occipitotemporal cortex in all 14 participants. This region, located in the lateral occipital sulcus, partially overlapped with left EBA, but could be functionally and anatomically dissociated from it. In experiment 2, we further investigated the functional profile of hand- and body-preferring regions by measuring responses to hands, fingers, feet, assorted body parts (arms, legs, torsos), and non-biological handlike stimuli such as robotic hands. The hand-preferring region responded most strongly to hands, followed by robotic hands, fingers, and feet, whereas its response to assorted body parts did not significantly differ from baseline. By contrast, EBA responded most strongly to body parts, followed by hands and feet, and did not significantly respond to robotic hands or fingers. Together, these results provide evidence for a representation of the hand in extrastriate visual cortex that is distinct from the representation of other body parts. PMID:20393066

Efficacy of enzymatic debridement of deeply burned hands.

PubMed

Krieger, Yuval; Bogdanov-Berezovsky, Alexander; Gurfinkel, Reuven; Silberstein, Eldad; Sagi, Amiram; Rosenberg, Lior

2012-02-01

The burned hand is a common and difficult to care-for entity in the field of burns. Due to the anatomy of the hand (important and delicate structures crowded in a small limited space without sub-dermal soft tissue), surgical debridement of the burned tissue is technically difficult and may cause considerable complications and, therefore, should be performed judiciously. Selective enzymatic debridement of the burn wound can preserve the spontaneous epithelialisation potential and reduce the added injury to the traumatised tissue added by a surgical debridement. The aim of the study was to assess the implication of a selective enzymatic compound (Debrase(®) - Ds) in the special field of deep hand burns, by comparing the actual burn area that required surgical coverage after enzymatic debridement to the burn area clinically judged to require skin grafting prior to debridement. This was a retrospective data collection and analysis from 154 complete files of prospective, open-label study in 275 hospitalised, Ds-treated burn patients. A total of 69 hand burns diagnosed as 'deep' was analysed; 36% of the wounds required surgical intervention after enzymatic debridement; 28.6% of the total burned area estimated initially as deep was covered by skin graft (statistically significant p<0.001). Debridement of deep-hand burns with a selective enzymatic agent decreased the perceived full-thickness wound area and skin-graft use. Copyright © 2011 Elsevier Ltd and ISBI. All rights reserved.

Protein-resistant cross-linked poly(vinyl alcohol) micropatterns via photolithography using removable polyoxometalate photocatalyst.

PubMed

Pavli, Pagona; Petrou, Panagiota S; Douvas, Antonios M; Dimotikali, Dimitra; Kakabakos, Sotirios E; Argitis, Panagiotis

2014-10-22

In the last years, there has been an increasing interest in controlling the protein adsorption properties of surfaces because this control is crucial for the design of biomaterials. On the other hand, controlled immobilization of proteins is also important for their application as solid surfaces in immunodiagnostics and biosensors. Herein we report a new protein patterning method where regions of the substrate are covered by a hydrophilic film that minimizes protein adsorption. Particularly, poly(vinyl alcohol) (PVA) cross-linked structures created by an especially developed photolithographic process are proved to prevent protein physisorption and they are used as a guide for selective protein adsorption on the uncovered areas of a protein adsorbing substrate such as polystyrene. The PVA cross-linking is induced by photo-oxidation using, as a catalyst, polyoxometalate (H3PW12O40 or α-(NH4)6P2W18O62), which is removed using a methyl alcohol/water mixed solvent as the developer. We demonstrate that the polystyrene and the cross-linked PVA exhibit dramatically different performances in terms of protein physisorption. In particular, the polystyrene areas presented up to 130 times higher protein binding capacity than the PVA ones, whereas the patterning resolution could easily reach dimensions of a few micrometers. The proposed approach can be applied on any substrate where PVA films can be coated for controlling protein adsorption onto surface areas custom defined by the user.

Integrated Optical and SAR Imagery with DEM to Quantify Glacier Water Storage Change in Upper Mekong River Basin

NASA Astrophysics Data System (ADS)

Liu, G. T.; Chen, J. B.; Le, T. S.; Chang, C. P.; Shum, C. K.; Tseng, K. H.

2015-12-01

In the past few decades, regional increase in air temperature has accelerated the ice melting in polar, sub-polar, and major land glacial areas. The glaciers in Tibetan Plateau, the largest glaciers outside Polar Regions and the sources of several trans-boundary major rivers, are now showing aggravated terminus retreat and thinning. The variation of freshwater availability is crucial for the economic development in Mainland Southeast Asia, especially in hydroelectric generation and agriculture irrigation. These rives, including the Mekong River, is also subject to upstream-downstream conflict and transboundary issues. In this study, we propose to estimate the remaining glacier water storage in Mekong River basin, and further analyze the impact of glacier retreat on these dams/reservoirs for the next decade. By calculating the Modified Normalized Difference Water Index (MNDWI), the water surface area (WSA) can thus be extracted from optical satellite images. On the other hand, the ice surface area (ISA) can be derived from the Polarimetric Synthetic Aperture Radar (POLSAR) images. With different polarization states of electromagnetic wave reflected by earth surface, POLSAR image can effectively identify glacier/ice from snow. Combined WSA and ISA information with digital elevation model (DEM), the change of freshwater storage in glaciers can be estimated. In the end, the influence on dams/reservoirs in the Mekong River caused by glacier retreat can be forecasted. The result can also be applied to hydrology, water allocation, and economy/agriculture policy determination.

Synthesis efficiency of heavy carbon clusters from ETFE ablated by different numbers of laser pulse in vacuum

NASA Astrophysics Data System (ADS)

Shibagaki, K.; Takada, N.; Sasaki, K.; Kadota, K.

2002-09-01

We have carried out mass spectral analysis of positive ions produced by laser ablation of a copolymer of ethylene and tetrafluoroethylene (ETFE: [CH 2CH 2CF 2CF 2] n) in vacuum using time-of-flight mass spectrometry (TOF-MS). The surfaces of the ETFE targets irradiated by different numbers of laser pulse were analyzed by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). Heavy carbon cluster ions C n+ with n≥30 were observed in the mass spectra. The fractional abundance of heavy clusters in the mass spectrum decreased with the number of laser pulse. On the other hand, carbon became rich in the atomic composition of the laser-irradiated surface, and the eroded area on the surface increased with the number of laser pulse. From these results, it is suggested that the carbon-rich material surface results in the less efficient production of heavy carbon clusters. In addition, it is also suggested that clustering reactions in eroded craters do not contribute to the synthesis of heavy clusters.

Sexual dimorphism and handedness in the human corpus callosum based on magnetic resonance imaging.

PubMed

Tuncer, M C; Hatipoğlu, E S; Ozateş, M

2005-08-01

The corpus callosum (CC) is a major anatomical and functional commissure linking the two cerebral hemispheres. With MR imaging in the sagittal plane, the corpus callosum can be depicted in great detail. Mid-sagittal magnetic resonance images of 80 normal individuals were analyzed to assess whether or not the morphology of the corpus callosum and its parts are related to sex and handedness. The subjects were 40 males (20 right-handers and 20 left-handers) and 40 females (20 right-handers and 20 left-handers). The midsagittal area of the corpus callosum was divided into seven sub-areas using Witelson's method. The most striking morphological changes concerned left-handers, who had larger areas of the anterior body, posterior body and isthmus than right-handers. In addition, right-handed males had larger rostrums and isthmuses than right-handed females. These significantly increased areas were related to handedness in right-handed males. However, left-handed males had larger anterior and posterior bodies than right-handed males. In contrast, there was no significant difference between left-handers and right-handers in females. The areas of the rostrum and posterior body of the corpus callosum increased significantly with sex in males. Moreover, there were no significant age-related changes in the total corpus callosum and sub-areas of the corpus callosum. In conclusion, these anatomical changes in corpus callosum morphology require taking the sexual definition and dominant handedness into consideration.

Determination of wetland ecosystem boundaries and validation of land use maps using remote sensing: Fuente de Piedra case study (Spain)

NASA Astrophysics Data System (ADS)

Sánchez, Antonio; Malak, Dania Abdul; Schröder, Christoph; Martinez-Murillo, Juan F.

2016-04-01

Remote sensing techniques (SRS) are valid tools for wetland monitoring that could support wetland managers in assessing the spatial and temporal changes in wetland ecosystems as well as in understanding their condition and the ecosystem services they provide. This study focuses on the one hand, on drawing hydro-ecological guidelines for the delimitation of wetland ecosystems; and on the other hand, to assess the reliability of widely available satellite images (Landsat) in estimating the land use/ land cover types covering wetlands. This research develops comprehensive guidelines to determine the boundaries of the Fuente de Piedra wetland ecosystem located in Andalusia, Spain and defines the main land use/ land cover classes covering this ecosystem using Landsat 8 images. An accuracy of the SRS results delivered is tested using the regional inventory of land use produced by the regional government of Andalusia in 2011. By using the ecological and hydrological settings of the area, the boundaries of the Fuente de Piedra wetland ecosystem are determined as an alternative to improve the current delimitations methodology (the Ramsar and Natura 2000 delineations), used by the local authorities so far and based mainly on administrative reasoning. In terms of the land use land cover definition in the area, Fuente de Piedra wetland ecosystem shows to cover a total area of 195 km2 composed mainly by agricultural areas (81.46%): olive groves, non-irrigated arable land and pastures, being 54.82%, 25.71% and 0.93% of the surface respectively. Wetland related land covers (water surface, wetland vegetation) represent 6.85% while natural vegetation is distributed in forest, 1.67%, and shrub areas, 4.14%, being 5.81% in total. 4.58% of the area corresponds to urban and other artificial surfaces. The rest, 1.30%, is composed of different areas without vegetation (sands, bare rock, dumps, etc.). The classification of the Landsat images made with the newly developed SWOS toolbox (under the Horizon 2020 SWOS project) provides reliable results (r2= 0.98). The image segmentation corresponds very closely with the plots of land observed in the satellite image, and the allocation of land use coverages corresponds in 82% of the segments. Forest and olive groves are the best identified coverages with an accuracy of 93% in both cases. Wetlands are correctly classified by 87%, where linear features (narrow streams, etc.) are not detected by the methodology used due to the limitations of Landsat resolution. Arable lands are classified with an accuracy of 85.5%; where the methodology seems to confuse this land use with sparse olive grove. In the case of shrubs, accuracy round the 72%, with confusions with this land use are related with arable land, sparse forests in wetland areas. In the case of urban areas, only 60.5% of the segments are correctly classified as the distinction between urban fabric and industrial areas does not seem to be possible and linear features are not detected (highways, secondary roads,…).

Finger-Shaped GelForce: Sensor for Measuring Surface Traction Fields for Robotic Hand.

PubMed

Sato, K; Kamiyama, K; Kawakami, N; Tachi, S

2010-01-01

It is believed that the use of haptic sensors to measure the magnitude, direction, and distribution of a force will enable a robotic hand to perform dexterous operations. Therefore, we develop a new type of finger-shaped haptic sensor using GelForce technology. GelForce is a vision-based sensor that can be used to measure the distribution of force vectors, or surface traction fields. The simple structure of the GelForce enables us to develop a compact finger-shaped GelForce for the robotic hand. GelForce that is developed on the basis of an elastic theory can be used to calculate surface traction fields using a conversion equation. However, this conversion equation cannot be analytically solved when the elastic body of the sensor has a complicated shape such as the shape of a finger. Therefore, we propose an observational method and construct a prototype of the finger-shaped GelForce. By using this prototype, we evaluate the basic performance of the finger-shaped GelForce. Then, we conduct a field test by performing grasping operations using a robotic hand. The results of this test show that using the observational method, the finger-shaped GelForce can be successfully used in a robotic hand.

Surface roughness of Saturn's rings and ring particles inferred from thermal phase curves

NASA Astrophysics Data System (ADS)

Morishima, Ryuji; Turner, Neal J.; Spilker, Linda

2017-10-01

We analyze thermal phase curves of all the main rings of Saturn (the A, B, C rings, and the Cassini division) measured by both the far-IR and mid-IR detectors of the Cassini Composite InfraRed Spectrometer (CIRS). All the rings show temperature increases toward zero phase angle, known as an opposition effect or thermal beaming. For the C ring and Cassini division, which have low optical depths, intra-particle shadowing is considered the dominant mechanism causing the effect. On the other hand, the phase curves of the optically thick B and A rings steepen significantly with decreasing absolute solar elevation angle from 21° to 14°, suggesting inter-particle shadowing plays an important role in these rings. We employ an analytic roughness model to estimate the degrees of surface roughness of the rings or ring particles. For optically thin rings, an isolated particle covered by spherical segment craters is employed while for the thick rings we approximate a packed particle layer as a slab covered by craters. The particles in the thin rings are found to have generally rough surfaces, except in the middle C ring. Across the C ring, the optical depth correlates with the degree of surface roughness. This may indicate that surface roughness comes mainly from particle clumping, while individual particles have rather smooth surfaces. For the optically thick rings, the surface roughness of the particle layer is found to be moderate. The modeled phase curves of optically thick rings are shallow if the phase angle change is primarily due to change of observer azimuthal angle. On the other hand, the phase curves are steep if the phase angle change is due to change of observer elevation angle, as inter-particle shadows become visible at higher observer elevation. In addition, the area of shadowed facets increases with decreasing solar elevation angle. These combined effects explain the large seasonal change of the phase curve steepness observed for the thick rings. The degrees of surface roughness inferred from the thermal phase curves are generally less than those from the phase curves in visible light. This is probably explained by different roughness scales seen in thermal and visible light.

A Surface-based Analysis of Language Lateralization and Cortical Asymmetry

PubMed Central

Greve, Douglas N.; Van der Haegen, Lise; Cai, Qing; Stufflebeam, Steven; Sabuncu, Mert R.; Fischl, Bruce; Bysbaert, Marc

2013-01-01

Among brain functions, language is one of the most lateralized. Cortical language areas are also some of the most asymmetrical in the brain. An open question is whether the asymmetry in function is linked to the asymmetry in anatomy. To address this question, we measured anatomical asymmetry in 34 participants shown with fMRI to have language dominance of the left hemisphere (LLD) and 21 participants shown to have atypical right hemisphere dominance (RLD). All participants were healthy and left-handed, and most (80%) were female. Gray matter (GM) volume asymmetry was measured using an automated surface-based technique in both ROIs and exploratory analyses. In the ROI analysis, a significant difference between LLD and RLD was found in the insula. No differences were found in planum temporale (PT), pars opercularis (POp), pars triangularis (PTr), or Heschl’s gyrus (HG). The PT, POp, insula, and HG were all significantly left lateralized in both LLD and RLD participants. Both the positive and negative ROI findings replicate a previous study using manually labeled ROIs in a different cohort [Keller, S. S., Roberts, N., Garcia-Finana, M., Mohammadi, S., Ringelstein, E. B., Knecht, S., et al. Can the language-dominant hemisphere be predicted by brain anatomy? Journal of Cognitive Neuroscience, 23, 2013–2029, 2011]. The exploratory analysis was accomplished using a new surface-based registration that aligns cortical folding patterns across both subject and hemisphere. A small but significant cluster was found in the superior temporal gyrus that overlapped with the PT. A cluster was also found in the ventral occipitotemporal cortex corresponding to the visual word recognition area. The surface-based analysis also makes it possible to disentangle the effects of GM volume, thickness, and surface area while removing the effects of curvature. For both the ROI and exploratory analyses, the difference between LLD and RLD volume laterality was most strongly driven by differences in surface area and not cortical thickness. Overall, there were surprisingly few differences in GM volume asymmetry between LLD and RLD indicating that gross morphometric asymmetry is only subtly related to functional language laterality. PMID:23701459

The Persistence of Illicit Drug Smoke Residues and their Recovery from Common Household Surfaces

PubMed Central

Bitter, Julie L.

2016-01-01

Third-hand smoke is the residue left remaining on surfaces during smoking events, and is composed of particles and vapors that form upon heating. The phrase “third-hand smoke” is primarily used to describe nicotine and other chemicals from cigarettes, but any residues formed from the smoking of various substances could be classified similarly. There has been an increasing body of research on third-hand smoke from cigarettes in the last decade, but little has been done in regards to understanding the persistence of particles and vapors from illicit drugs. In this work, small samples of cocaine and methamphetamine were volatilized to produce an illicit drug smoke that was collected onto various surface materials and left exposed to ambient conditions over 672 hours (four weeks). Chemical analyses by electrospray ionization-mass spectrometry of residues on silicon, plastic, laminate, and artificial leather surfaces indicated a rapid decrease in recovery of the parent molecule, with varied formation of decomposition products over the first 168 hours of exposure. Measurable amounts of the parent molecule were still present after 672 hours, exhibiting a strong persistence of these drugs on various household materials. This is important in a forensic science context, as third-hand smoke residues could provide a viable source of trace evidence previously not utilized. PMID:27328798

Linking physics with physiology in TMS: a sphere field model to determine the cortical stimulation site in TMS.

PubMed

Thielscher, Axel; Kammer, Thomas

2002-11-01

A fundamental problem of transcranial magnetic stimulation (TMS) is determining the site and size of the stimulated cortical area. In the motor system, the most common procedure for this is motor mapping. The obtained two-dimensional distribution of coil positions with associated muscle responses is used to calculate a center of gravity on the skull. However, even in motor mapping the exact stimulation site on the cortex is not known and only rough estimates of its size are possible. We report a new method which combines physiological measurements with a physical model used to predict the electric field induced by the TMS coil. In four subjects motor responses in a small hand muscle were mapped with 9-13 stimulation sites at the head perpendicular to the central sulcus in order to keep the induced current direction constant in a given cortical region of interest. Input-output functions from these head locations were used to determine stimulator intensities that elicit half-maximal muscle responses. Based on these stimulator intensities the field distribution on the individual cortical surface was calculated as rendered from anatomical MR data. The region on the cortical surface in which the different stimulation sites produced the same electric field strength (minimal variance, 4.2 +/- 0.8%.) was determined as the most likely stimulation site on the cortex. In all subjects, it was located at the lateral part of the hand knob in the motor cortex. Comparisons of model calculations with the solutions obtained in this manner reveal that the stimulated cortex area innervating the target muscle is substantially smaller than the size of the electric field induced by the coil. Our results help to resolve fundamental questions raised by motor mapping studies as well as motor threshold measurements.

Continuous gravimetric monitoring as an integrative tool for exploring hydrological processes in the Lomme Karst System (Belgium)

NASA Astrophysics Data System (ADS)

Watlet, A.; Van Camp, M. J.; Poulain, A.; Hallet, V.; Rochez, G.; Quinif, Y.; Meus, P.; Kaufmann, O.; Francis, O.

2016-12-01

Karst systems are highly heterogeneous which makes their hydrology difficult to understand. Geophysical techniques offer non-invasive and integrative methods that help interpreting such systems as a whole. Among these techniques, gravimetry has been increasingly used in the last decade to characterize the hydrological behavior of complex systems, e.g. karst environments or volcanoes. We present a continuous microgravimetric monitoring of 3 years in the karstic area of Rochefort (Belgium), that shows multiple occurrences of caves and karstic features. The gravity record includes measurements of a GWR superconducting gravimeter, a Micro-g LaCoste gPhone and an absolute FG5 gravimeter. Together with meteorological measurements and a surface/in-cave hydrogeological monitoring, we were able to improve the knowledge of hydrological processes. On the one hand, the data allowed identifying seasonal groundwater content changes in the unsaturated zone of the karst area, most likely to be linked to temporary groundwater storage occurring in the most karstified layers closed to the surface. Combined with additional geological information, modelling of the gravity signal based on the vertical potential of the gravitational attraction was then particularly useful to estimate the seasonal recharge leading to the temporary subsurface groundwater storage. On the other hand, the gravity monitoring of flash floods occurring in deeper layers after intense rainfall events informed on the effective porosity gradient of the limestones. Modelling was then helpful to identify the hydrogeological role played by the cave galleries with respect to the hosting limestones during flash floods. These results are also compared with measurements of an in-cave gravimetric monitoring performed with a gPhone spring gravimeter. An Electrical Resistivity Tomography monitoring is also conducted at site and brings additional information useful to verify the interpretation made with the gravimetric monitoring.

Effect of blocking tactile information from the fingertips on adaptation and execution of grip forces to friction at the grasping surface.

PubMed

Bilaloglu, Seda; Lu, Ying; Geller, Daniel; Rizzo, John Ross; Aluru, Viswanath; Gardner, Esther P; Raghavan, Preeti

2016-03-01

Adaptation of fingertip forces to friction at the grasping surface is necessary to prevent use of inadequate or excessive grip forces. In the current study we investigated the effect of blocking tactile information from the fingertips noninvasively on the adaptation and efficiency of grip forces to surface friction during precision grasp. Ten neurologically intact subjects grasped and lifted an instrumented grip device with 18 different frictional surfaces under three conditions: with bare hands or with a thin layer of plastic (Tegaderm) or an additional layer of foam affixed to the fingertips. The coefficient of friction at the finger-object interface of each surface was obtained for each subject with bare hands and Tegaderm by measuring the slip ratio (grip force/load force) at the moment of slip. We found that the foam layer reduced sensibility for two-point discrimination and pressure sensitivity at the fingertips, but Tegaderm did not. However, Tegaderm reduced static, but not dynamic, tactile discrimination. Adaptation of fingertip grip forces to surface friction measured by the rate of change of peak grip force, and grip force efficiency measured by the grip-load force ratio at lift, showed a proportional relationship with bare hands but were impaired with Tegaderm and foam. Activation of muscles engaged in precision grip also varied with the frictional surface with bare hands but not with Tegaderm and foam. The results suggest that sensitivity for static tactile discrimination is necessary for feedforward and feedback control of grip forces and for adaptive modulation of muscle activity during precision grasp. Copyright © 2016 the American Physiological Society.

vmdICE: a plug-in for rapid evaluation of molecular dynamics simulations using VMD.

PubMed

Knapp, Bernhard; Lederer, Nadja; Omasits, Ulrich; Schreiner, Wolfgang

2010-12-01

Molecular dynamics (MD) is a powerful in silico method to investigate the interactions between biomolecules. It solves Newton's equations of motion for atoms over a specified period of time and yields a trajectory file, containing the different spatial arrangements of atoms during the simulation. The movements and energies of each single atom are recorded. For evaluating of these simulation trajectories with regard to biomedical implications, several methods are available. Three well-known ones are the root mean square deviation (RMSD), the root mean square fluctuation (RMSF) and solvent accessible surface area (SASA). Herein, we present a novel plug-in for the software "visual molecular dynamics" (VMD) that allows an interactive 3D representation of RMSD, RMSF, and SASA, directly on the molecule. On the one hand, our plug-in is easy to handle for inexperienced users, and on the other hand, it provides a fast and flexible graphical impression of the spatial dynamics of a system for experts in the field. © 2010 Wiley Periodicals, Inc.

Erkundung und Beweissicherung für eine geothermale Erschließung eines Alpinen Karstaquifers im Tuxertal, Österreich

NASA Astrophysics Data System (ADS)

Sass, Ingo; Heldmann, Claus-Dieter; Schäffer, Rafael

2016-06-01

Karst aquifers may on one hand improve the efficiency of geothermal systems due to increased permeabilities, but on the other hand, high groundwater velocities can reduce the efficiency of the underground heat storage capacity. The marble karst aquifer of the Hochstegen formation was explored and developed for the first time as an intermediate-depth geothermal energy storage system at Finkenberg, Tux valley (Tyrol, Austria). Geological field studies and a spring monitoring program for the project revealed characteristic hydro-chemical signatures related to the catchments in specific tectonic units depending on their lithology. Observations showed that the catchment area of the Hochstegen formation karst aquifer extends up to 2650 m a.s.l. southwest of Finkenberg. In the boreholes, karstification was detected to 400 m below surface (Sass et al., 2016). A monitoring program involving seven springs downgradient of the boreholes has shown that the geothermal project has had no long-term impact on groundwater quality.

Kite-flying: a unique but dangerous mode of electrical injury in children.

PubMed

Tiwari, V K; Sharma, D

1999-09-01

A retrospective study was conducted to evaluate the cause of a sudden rise in number of pediatric admissions with electrical injuries at our centre during the year 1998. In evaluating the cause, six out of twelve admissions were found to be related to kite-flying which is a popular sport during the months of June, July, August and September. In two out of six cases current travelled directly through the string of the kite. In two others, flame burns occured following ignition of clothing. Another patient had contact with wire through a metal rod. In the last case, arcing pulled the hand of the patient leading to direct contact with wire. The average burns size was approximately 31% body surface area (BSA), with all patients having burns over the palmar aspect of at least one hand. No patient required amputation for the injuries. In this article, attention has been focussed on the various modes of electrical injuries associated with kite-flying and some measures have been advised to avoid such accidents.

Typhoon Yolanda/Haiyan and climate justice.

PubMed

Yamada, Seiji; Galat, Absalon

2014-10-01

The extreme weather events that the world is experiencing are consistent with the effects of anthropogenic climate change. The western North Pacific is the area of the world with the most intense tropical cyclones. Increased sea surface temperatures directly contribute to the wind speed of storms. The 2013 Typhoon Yolanda/Haiyan was the strongest tropical cyclone in recorded history to make landfall-causing more than 6000 deaths in the Philippines, mostly from storm surge. This event represents a climate injustice. On one hand, disaster prevention and preparedness were inadequate for impoverished populations in the Philippines who lived in poorly constructed housing. While the international community assisted with the response, recovery was hampered by inadequate and inequitable investment. On the other hand, climate change has been driven by the carbon emissions of industrialized states. Those who call for climate justice argue for more robust measures to control carbon emissions responsible for climate change and worsening global health security. As global citizens and as health professionals, we examine the implications for all of us as moral actors.

Drift from the Use of Hand-Held Knapsack Pesticide Sprayers in Boyacá (Colombian Andes).

PubMed

García-Santos, Glenda; Feola, Giuseppe; Nuyttens, David; Diaz, Jaime

2016-05-25

Offsite pesticide losses in tropical mountainous regions have been little studied. One example is measuring pesticide drift soil deposition, which can support pesticide risk assessment for surface water, soil, bystanders, and off-target plants and fauna. This is considered a serious gap, given the evidence of pesticide-related poisoning in those regions. Empirical data of drift deposition of a pesticide surrogate, Uranine tracer, within one of the highest potato-producing regions in Colombia, characterized by small plots and mountain orography, is presented. High drift values encountered in this study reflect the actual spray conditions using hand-held knapsack sprayers. Comparison between measured and predicted drift values using three existing empirical equations showed important underestimation. However, after their optimization based on measured drift information, the equations showed a strong predictive power for this study area and the study conditions. The most suitable curve to assess mean relative drift was the IMAG calculator after optimization.

Design options for improving protective gloves for industrial assembly work.

PubMed

Dianat, Iman; Haslegrave, Christine M; Stedmon, Alex W

2014-07-01

The study investigated the effects of wearing two new designs of cotton glove on several hand performance capabilities and compared them against the effects of barehanded, single-layered and double cotton glove conditions when working with hand tools (screwdriver and pliers). The new glove designs were based on the findings of subjective hand discomfort assessments for this type of work and aimed to match the glove thickness to the localised pressure and sensitivity in different areas of the hand as well as to provide adequate dexterity for fine manipulative tasks. The results showed that the first prototype glove and the barehanded condition were comparable and provided better dexterity and higher handgrip strength than double thickness gloves. The results support the hypothesis that selective thickness in different areas of the hand could be applied by glove manufacturers to improve the glove design, so that it can protect the hands from the environment and at the same time allow optimal hand performance capabilities. Copyright © 2014 Elsevier Ltd and The Ergonomics Society. All rights reserved.

[Adequate prescription and application of topicals : How to calculate the right volume for the prescription of ointment needed?

PubMed

Homayoon, D; Dahlhoff, P; Augustin, M

2017-12-15

Uncertainty regarding the suitable amount of prescribed ointment and its application by patients may cause insufficient or uneconomic health care provision. To address this issue, standardized methods and experts' knowledge on the suitable amount and coherent patient's elucidation for application of topicals are needed. Presented are current data in routine care and scientific evidence on the prescribed amount of topical agents as well as its application by patients in dermatological care. A literature review was conducted via PubMed using the keywords as individual and pooled search terms: "local therapy", "topical treatment", "prescription", "amount of ointment needed", "involved area", "BSA", "finger-tip-unit", "Rule of Hand", "calculated dosage" and "rule of nines". We included original studies by manually screening title and abstract according to the relevance of the topic. The search strategy identified 19 clinical trials. The fingertip unit (FTU) is the most frequently used measurement for accurate application of external agents. Appropriate prescribed amount is calculated by required topical agent per involved surface area. There is still a need for clarification to which extent the optimized amount of ointment is prescribed and advice for its application in routine care is given. The FTU combined with the "Rule of Hand" is an adequate measurement for patient's guidance on self-application.

Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files.

PubMed

Soni, Dileep; Raisingani, Deepak; Mathur, Rachit; Madan, Nidha; Visnoi, Suchita

2016-01-01

To evaluate the incidence of apical crack initiation during canal preparation with stainless steel K-files and hand protaper files (in vitro study). Sixty extracted mandibular premo-lar teeth are randomly selected and embedded in an acrylic tube filled with autopolymerizing resin. A baseline image of the apical surface of each specimen was recorded under a digital microscope (80×). The cervical and middle thirds of all samples were flared with #2 and #1 Gates-Glidden (GG) drills, and a second image was recorded. The teeth were randomly divided into four groups of 15 teeth each according to the file type (hand K-file and hand-protaper) and working length (WL) (instrumented at WL and 1 mm less than WL). Final image after dye penetration and photomicrograph of the apical root surface were digitally recorded. Maximum numbers of cracks were observed with hand protaper files compared with hand K-file at the WL and 1 mm short of WL. Chi-square testing revealed a highly significant effect of WL on crack formation at WL and 1 mm short of WL (p = 0.000). Minimum numbers of cracks at WL and 1 mm short of WL were observed with hand K-file and maximum with hand protaper files. Soni D, Raisingani D, Mathur R, Madan N, Visnoi S. Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files. Int J Clin Pediatr Dent 2016;9(4):303-307.

Case study on the orientation of phaco hand pieces during steam sterilization processes.

PubMed

van Doornmalen Gomez Hoyos, J P C M; van Wezel, R A C; van Doornmalen, H W J M

2015-05-01

Steam sterilization is an essential part of infection prevention. The literature shows that sterilization of medical instruments containing channels is not trivial. Phaco hand pieces have a simple configuration: a device contains a channel with a constant radius. No literature was found indicating whether the sterilization conditions on the inner surface of a phaco hand piece are influenced by the orientation of the hand piece. To determine whether the orientation of a phaco hand piece influences the results of a sterilization process of this device. A qualitative case study, including experiments, is performed with a protocolled combination of steam sterilizer, process, phaco hand piece, orientation of the phaco hand piece, and wrapping. In this specific case, the orientation of the hand piece influenced the result of the steam sterilization process; in vertically (upright) oriented phaco hand pieces with free water drainage, sterilization conditions are reproducibly established. In the same process, in horizontally oriented or vertically oriented hand pieces without free drainage, these conditions are not established in a reproducible way. In the investigated combination of sterilizer, process, load, loading pattern and wrapping, phaco hand pieces have to be oriented vertically (upright) with free water drainage to obtain steam sterilization conditions on the inner surface. It is likely that instruments with comparable configuration and dimensions will yield comparable results. It is therefore recommended that this issue is considered during the development of medical instruments and during performance qualifications of such instruments. Copyright © 2015 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Depicting the inner and outer nose: the representation of the nose and the nasal mucosa on the human primary somatosensory cortex (SI).

PubMed

Gastl, Mareike; Brünner, Yvonne F; Wiesmann, Martin; Freiherr, Jessica

2014-09-01

The nose is important not only for breathing, filtering air, and perceiving olfactory stimuli. Although the face and hands have been mapped, the representation of the internal and external surface of the nose on the primary somatosensory cortex (SI) is still poorly understood. To fill this gap functional magnetic resonance imaging (fMRI) was used to localize the nose and the nasal mucosa in the Brodman areas (BAs) 3b, 1, and 2 of the human postcentral gyrus (PG). Tactile stimulation during fMRI was applied via a customized pneumatically driven device to six stimulation sites: the alar wing of the nose, the lateral nasal mucosa, and the hand (serving as a reference area) on the left and right side of the body. Individual representations could be discriminated for the left and right hand, for the left nasal mucosa and left alar wing of the nose in BA 3b and BA 1 by comparing mean activation maxima and Euclidean distances. Right-sided nasal conditions and conditions in BA 2 could further be separated by different Euclidean distances. Regarding the alar wing of the nose, the results concurred with the classic sensory homunculus proposed by Penfield and colleagues. The nasal mucosa was not only determined an individual and bilateral representation, its position on the somatosensory cortex is also situated closer to the caudal end of the PG compared to that of the alar wing of the nose and the hand. As SI is commonly activated during the perception of odors, these findings underscore the importance of the knowledge of the representation of the nasal mucosa on the primary somatosensory cortex, especially for interpretation of results of functional imaging studies about the sense of smell. Copyright © 2014 Wiley Periodicals, Inc.

Thumb Reach of Indonesian Young Adult When Interacting with Touchscreen of Single-Handed Device: A Preliminary Study

NASA Astrophysics Data System (ADS)

Umami, M. K.

2018-01-01

This study is a preliminary survey on thumb reach of Indonesian population when interacting with single-handed device. This study was aimed to know the thumb reach envelope on the screen of mobile phone. The correlation between the thumb reach vs. the hand length and thumb length was also identified. Thirty young adults participated in the study. All participants had normal body stature and were right-handed person. In the observational phase, the participant was asked to colour the canvas area on the screen of the mobile phone by using his/her thumb. The participant had to complete the task by applying the single hand interaction. The participant should grab the mobile phone as he/she use it normally in his/her daily activities. The thumb reach envelope of participants was identified from the coloured area of the canvas. The results of this study found that participants with a large hand length and thumb length tend to have a large thumb reach. The results of this study also show the thumb reach area of the participants is forming an elliptical shape that runs from the northeast to southwest on the device screen.

Mars Researchers Rendezvous on Remote Arctic Island

NASA Technical Reports Server (NTRS)

2002-01-01

Devon Island is situated in an isolated part of Canada's Nunavut Territory, and is usually considered to be the largest uninhabited island in the world. However, each summer since 1999, researchers from NASA's Haughton-Mars Project and the Mars Society reside at this 'polar desert' location to study the geologic and environmental characteristics of a site which is considered to be an excellent 'Mars analog': a terrestrial location wherein specific conditions approximate environmental features reported on Mars. Base camps established amidst the rocks and rubble surrounding the Haughton impact crater enable researchers to conduct surveys designed to test the habitat, equipment and technology that may be deployed during a human mission to Mars. One of the many objectives of the project scientists is to understand the ice formations around the Haughton area, in the hopes that this might ultimately assist with the recognition of areas where ice can be found at shallow depth on Mars.

These images of Devon Island from NASA's Multi-angle Imaging SpectroRadiometer (MISR) instrument provide contrasting views of the spectral and angular reflectance 'signatures' of different surfaces within the region. The top panel is a natural color view created with data from the red, green and blue-bands of MISR's nadir (vertical-viewing) camera. The bottom panel is a false-color multiangular composite of the same area, utilizing red band data from MISR's 60-degree backward, nadir, and 60-degree forward-viewing cameras, displayed as red, green and blue, respectively. In this representation, colors highlight textural properties of elements within the scene, with blue tones indicating smooth surfaces (which preferentially forward scatter sunlight) and red hues indicating rougher surfaces (which preferentially backscatter). The angular reflectance 'signature' of low clouds causes them to appear purple, and this visualization provides a unique way of distinguishing clouds from snow and ice.

The data were captured on June 28, 2001, during the early part of the arctic summer, when sea ice becomes thinner and begins to move depending upon localized currents and winds. In winter the entire region is locked with several meters of nearly motionless sea ice, which acts as a thermodynamic barrier to the loss of heat from the comparatively warm ocean to the colder atmosphere. Summer melting of sea ice can be observed at the two large, dark regions of open water; one is present in the Jones Sound (near the top to the left of center), and another appears in the Wellington Channel (left-hand edge). A large crack caused by tidal heaving has broken the ice cover over the Parry Channel (lower right-hand corner). A substantial ice cap permanently occupies the easternmost third of the island (upper right). Surface features such as dendritic meltwater channels incised into the island's surface are apparent. The Haughton-Mars project site is located slightly to the left and above image center, in an area which appears with relatively little surface ice, near the island's inner 'elbow.'

The images were acquired during Terra orbit 8132 and cover an area of about 334 kilometers x 229 kilometers. They utilize data from blocks 27 to 31 within World Reference System-2 path 42.

MISR was built and is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

Motor skill for tool-use is associated with asymmetries in Broca's area and the motor hand area of the precentral gyrus in chimpanzees (Pan troglodytes).

PubMed

Hopkins, William D; Meguerditchian, Adrien; Coulon, Olivier; Misiura, Maria; Pope, Sarah; Mareno, Mary Catherine; Schapiro, Steven J

2017-02-01

Among nonhuman primates, chimpanzees are well known for their sophistication and diversity of tool use in both captivity and the wild. The evolution of tool manufacture and use has been proposed as a driving mechanism for the development of increasing brain size, complex cognition and motor skills, as well as the population-level handedness observed in modern humans. Notwithstanding, our understanding of the neurological correlates of tool use in chimpanzees and other primates remains poorly understood. Here, we assessed the hand preference and performance skill of chimpanzees on a tool use task and correlated these data with measures of neuroanatomical asymmetries in the inferior frontal gyrus (IFG) and the pli-de-passage fronto-parietal moyen (PPFM). The IFG is the homolog to Broca's area in the chimpanzee brain and the PPFM is a buried gyrus that connects the pre- and post-central gyri and corresponds to the motor-hand area of the precentral gyrus. We found that chimpanzees that performed the task better with their right compared to left hand showed greater leftward asymmetries in the IFG and PPFM. This association between hand performance and PPFM asymmetry was particularly robust for right-handed individuals. Based on these findings, we propose that the evolution of tool use was associated with increased left hemisphere specialization for motor skill. We further suggest that lateralization in motor planning, rather than hand preference per se, was selected for with increasing tool manufacture and use in Hominid evolution. Copyright © 2016 Elsevier B.V. All rights reserved.

Where one hand meets the other: limb-specific and action-dependent movement plans decoded from preparatory signals in single human frontoparietal brain areas.

PubMed

Gallivan, Jason P; McLean, D Adam; Flanagan, J Randall; Culham, Jody C

2013-01-30

Planning object-directed hand actions requires successful integration of the movement goal with the acting limb. Exactly where and how this sensorimotor integration occurs in the brain has been studied extensively with neurophysiological recordings in nonhuman primates, yet to date, because of limitations of non-invasive methodologies, the ability to examine the same types of planning-related signals in humans has been challenging. Here we show, using a multivoxel pattern analysis of functional MRI (fMRI) data, that the preparatory activity patterns in several frontoparietal brain regions can be used to predict both the limb used and hand action performed in an upcoming movement. Participants performed an event-related delayed movement task whereby they planned and executed grasp or reach actions with either their left or right hand toward a single target object. We found that, although the majority of frontoparietal areas represented hand actions (grasping vs reaching) for the contralateral limb, several areas additionally coded hand actions for the ipsilateral limb. Notable among these were subregions within the posterior parietal cortex (PPC), dorsal premotor cortex (PMd), ventral premotor cortex, dorsolateral prefrontal cortex, presupplementary motor area, and motor cortex, a region more traditionally implicated in contralateral movement generation. Additional analyses suggest that hand actions are represented independently of the intended limb in PPC and PMd. In addition to providing a unique mapping of limb-specific and action-dependent intention-related signals across the human cortical motor system, these findings uncover a much stronger representation of the ipsilateral limb than expected from previous fMRI findings.

Motor skill for tool-use is associated with asymmetries in Broca’s area and the motor hand area of the precentral gyrus in chimpanzees (Pan troglodytes)

PubMed Central

Hopkins, William D.; Meguerditchian, Adrien; Coulon, Olivier; Misiura, Maria; Pope, Sarah; Mareno, Mary Catherine; Schapiro, Steven J.

2017-01-01

Among nonhuman primates, chimpanzees are well known for their sophistication and diversity of tool use in both captivity and the wild. The evolution of tool manufacture and use has been proposed as a driving mechanism for the development of increasing brain size, complex cognition and motor skills, as well as the population-level handedness observed in modern humans. Notwithstanding, our understanding of the neurological correlates of tool use in chimpanzees and other primates remains poorly understood. Here, we assessed the hand preference and performance skill of chimpanzees on a tool use task and correlated these data with measures of neuroanatomical asymmetries in the inferior frontal gyrus (IFG) and the pli-de-passage fronto-parietal moyen (PPFM). The IFG is the homolog to Broca’s area in the chimpanzee brain and the PPFM is a buried gyrus that connects the pre- and post-central gyri and corresponds to the motor-hand area of the precentral gyrus. We found that chimpanzees that performed the task better with their right compared to left hand showed greater leftward asymmetries in the IFG and PPFM. This association between hand performance and PPFM asymmetry was particularly robust for right-handed individuals. Based on these findings, we propose that the evolution of tool use was associated with increased left hemisphere specialization for motor skill. We further suggest that lateralization in motor planning, rather than hand preference per se, was selected for with increasing tool manufacture and use in Hominid evolution. PMID:27816558

Dynamical characteristics of surface EMG signals of hand grasps via recurrence plot.

PubMed

Ouyang, Gaoxiang; Zhu, Xiangyang; Ju, Zhaojie; Liu, Honghai

2014-01-01

Recognizing human hand grasp movements through surface electromyogram (sEMG) is a challenging task. In this paper, we investigated nonlinear measures based on recurrence plot, as a tool to evaluate the hidden dynamical characteristics of sEMG during four different hand movements. A series of experimental tests in this study show that the dynamical characteristics of sEMG data with recurrence quantification analysis (RQA) can distinguish different hand grasp movements. Meanwhile, adaptive neuro-fuzzy inference system (ANFIS) is applied to evaluate the performance of the aforementioned measures to identify the grasp movements. The experimental results show that the recognition rate (99.1%) based on the combination of linear and nonlinear measures is much higher than those with only linear measures (93.4%) or nonlinear measures (88.1%). These results suggest that the RQA measures might be a potential tool to reveal the sEMG hidden characteristics of hand grasp movements and an effective supplement for the traditional linear grasp recognition methods.

Effect of reduction of area on microstructure and mechanical properties of twinning-induced plasticity steel during wire drawing

NASA Astrophysics Data System (ADS)

Hwang, Joong-Ki; Son, Il-Heon; Yoo, Jang-Yong; Zargaran, A.; Kim, Nack J.

2015-09-01

The effect of reduction of area (RA), 10%, 20%, and 30%, during wire drawing on the inhomogeneities in microstructure and mechanical properties along the radial direction of Fe-Mn-Al-C twinning-induced plasticity steel has been investigated. After wire drawing, the deformation texture developed into the major <111> and minor <100> duplex fiber texture. However, the <111> texture became more pronounced in both center and surface areas as the RA per pass increased. It also shows that a larger RA per pass resulted in a higher yield strength and smaller elongation than a smaller RA per pass at all strain levels. Although inhomogeneities in microstructure and mechanical properties along the radial direction decreased with increasing RA per pass, there existed an optimum RA per pass for maximum drawing limit. Insufficient penetration of strain from surface to center at small RA per pass (e.g., 10%) and high friction and unsound metal flow at large RA per pass (e.g., 30%) all resulted in heterogeneous microstructure and mechanical properties along the radial direction of drawn wire. On the other hand, 20% RA per pass improved the drawing limit by about 30% as compared to the 10% and 30% RAs per pass.

Analysis and comparison of modern methods of turf irrigation, verifying the capability of existing information systems through the use of numerical modeling

NASA Astrophysics Data System (ADS)

Deangelis, Maria Laura; Facoetti, Nicola

2016-04-01

The automated irrigation of parks and gardens in public areas has become more and more a common practice due to the many benefits it brings in terms of improving the quality of urban green areas. Since this practice requires significant volumes of water, and this becomes increasingly scarce and expensive, it is necessary that the design criteria and use management aim at maximizing the irrigation efficiency. There are conflicting relationship and competition between trees and turf for several reasons. On one hand the different irrigation needs can cause excess water in the root zones of the trees, on the other hand the surface roots of trees and the shade created from the leaves by the dripline (projection line of the canopy) determine an unfavorable area to the growth of the turf because of light factor. It follows that for an optimal design of an irrigation system is necessary to separate the turf areas from trees, with the disadvantage of considerably complicate the geometries of the sprinklers. Each tree or group of trees need to be associated to a not irrigated area. This problem seems not to have a specifically bibliographical evidence, although there are operating standards primarily used to define buffer zones for trees from constructions (British Standard 5837:2005). Ideally, a high number of sprinklers is required to follow the shape of the areas perfectly. Hence, an additional step is necessary to simplify these geometries, identifying a correct scheme for the sprinkler spacing. Such a sequence of geometric operations has been tested on the "Indro Montanelli" park in Milan, obtaining a reduction of the irrigated area of 47% and a water saving of around 30%. We intend to continue the research applying the model to other parks, verifying its applicability in different situations.

Changes in cortical, cerebellar and basal ganglia representation after comprehensive long term unilateral hand motor training.

PubMed

Walz, A D; Doppl, K; Kaza, E; Roschka, S; Platz, T; Lotze, M

2015-02-01

We were interested in motor performance gain after unilateral hand motor training and associated changes of cerebral and cerebellar movement representation tested with functional magnetic resonance imaging (fMRI) before and after training. Therefore, we trained the left hand of strongly right-handed healthy participants with a comprehensive training (arm ability training, AAT) over two weeks. Motor performance was tested for the trained and non-trained hand before and after the training period. Functional imaging was performed for the trained and the non-trained hand separately and comprised force modulation with the fist, sequential finger movements and a fast writing task. After the training period the performance gain of tapping movements was comparable for both hand sides, whereas the motor performance for writing showed a higher training effect for the trained hand. fMRI showed a reduction of activation in supplementary motor, dorsolateral prefrontal cortex, parietal cortical areas and lateral cerebellar areas during sequential finger movements over time. During left hand writing lateral cerebellar hemisphere also showed reduced activation, while activation of the anterior cerebellar hemisphere was increased. An initially high anterior cerebellar activation magnitude was a predictive value for high training outcome of finger tapping and visual guided movements. During the force modulation task we found increased activation in the striate. Overall, a comprehensive long-term training of the less skillful hand in healthy participants resulted in relevant motor performance improvements, as well as an intermanual learning transfer differently pronounced for the type of movement tested. Whereas cortical motor area activation decreased over time, cerebellar anterior hemisphere and striatum activity seem to represent increasing resources after long-term motor training. Copyright © 2014 Elsevier B.V. All rights reserved.

Spatial and Temporal Eye–Hand Coordination Relies on the Parietal Reach Region

PubMed Central

Hauschild, Markus; Wilke, Melanie; Andersen, Richard A.

2014-01-01

Coordinated eye movements are crucial for precision control of our hands. A commonly believed neural mechanism underlying eye–hand coordination is interaction between the neural networks controlling each effector, exchanging, and matching information, such as movement target location and onset time. Alternatively, eye–hand coordination may result simply from common inputs to independent eye and hand control pathways. Thus far, it remains unknown whether and where either of these two possible mechanisms exists. A candidate location for the former mechanism, interpathway communication, includes the posterior parietal cortex (PPC) where distinct effector-specific areas reside. If the PPC were within the network for eye–hand coordination, perturbing it would affect both eye and hand movements that are concurrently planned. In contrast, if eye–hand coordination arises solely from common inputs, perturbing one effector pathway, e.g., the parietal reach region (PRR), would not affect the other effector. To test these hypotheses, we inactivated part of PRR in the macaque, located in the medial bank of the intraparietal sulcus encompassing the medial intraparietal area and area 5V. When each effector moved alone, PRR inactivation shortened reach but not saccade amplitudes, compatible with the known reach-selective activity of PRR. However, when both effectors moved concurrently, PRR inactivation shortened both reach and saccade amplitudes, and decoupled their reaction times. Therefore, consistent with the interpathway communication hypothesis, we propose that the planning of concurrent eye and hand movements causes the spatial information in PRR to influence the otherwise independent eye control pathways, and that their temporal coupling requires an intact PRR. PMID:25232123

Bacterial Contamination of Hands Increases Risk of Cross-Contamination among Low-Income Puerto Rican Meal Preparers

ERIC Educational Resources Information Center

Dharod, Jigna Morarji; Paciello, Stefania; Bermudez-Millan, Angela; Venkitanarayanan, Kumar; Damio, Grace; Perez-Escamilla, Rafael

2009-01-01

Objective: To examine the association of microbial contamination of the meal preparer's hands with microbial status of food and kitchen/utensil surfaces during home preparation of a "Chicken and Salad" meal. Design and Setting: Observational home food safety assessment. Before starting meal preparation, participants' hands were tested to…

Eye-hand coupling during closed-loop drawing: evidence of shared motor planning?

PubMed

Reina, G Anthony; Schwartz, Andrew B

2003-04-01

Previous paradigms have used reaching movements to study coupling of eye-hand kinematics. In the present study, we investigated eye-hand kinematics as curved trajectories were drawn at normal speeds. Eye and hand movements were tracked as a monkey traced ellipses and circles with the hand in free space while viewing the hand's position on a computer monitor. The results demonstrate that the movement of the hand was smooth and obeyed the 2/3 power law. Eye position, however, was restricted to 2-3 clusters along the hand's trajectory and fixed approximately 80% of the time in one of these clusters. The eye remained stationary as the hand moved away from the fixation for up to 200 ms and saccaded ahead of the hand position to the next fixation along the trajectory. The movement from one fixation cluster to another consistently occurred just after the tangential hand velocity had reached a local minimum, but before the next segment of the hand's trajectory began. The next fixation point was close to an area of high curvature along the hand's trajectory even though the hand had not reached that point along the path. A visuo-motor illusion of hand movement demonstrated that the eye movement was influenced by hand movement and not simply by visual input. During the task, neural activity of pre-motor cortex (area F4) was recorded using extracellular electrodes and used to construct a population vector of the hand's trajectory. The results suggest that the saccade onset is correlated in time with maximum curvature in the population vector trajectory for the hand movement. We hypothesize that eye and arm movements may have common, or shared, information in forming their motor plans.

Differential activation in the primary motor cortex during individual digit movement in focal hand dystonia vs. healthy.

PubMed

Kimberley, Teresa J; Pickett, Kristen A

2012-01-01

The pathophysiology of focal hand dystonia (FHD) is not clearly understood. Previous studies have reported increased and decreased cortical activity associated with motor tasks. The aim of this study was to investigate blood oxygen level dependent (BOLD) signal changes in functional magnetic resonance imaging within the hand area of primary motor cortex during cued movement of individual digits. Eight healthy individuals and five individuals with right hand FHD participated. Beta weight contrasts were examined within the hand area of the motor cortex. In both groups, BOLD signal changes in the hemisphere contralateral to the moving hand were greater in the left hemisphere than the right. Between groups, no difference was found during control of the left hand, but a significant difference was seen during right hand movement; specifically, individuals with dystonia showed increased contralateral and decreased ipsilateral cortical response associated with the affected hand as compared to healthy individuals. This suggests a similar, albeit exaggerated pattern of activation in individuals with FHD on the affected side. These results suggest different levels of ipsilateral and contralateral activation between healthy and dystonic individuals but also show a relative difference between symptomatic and asymptomatic control within the patient population.

Southern Quebec in Late Winter

NASA Technical Reports Server (NTRS)

2002-01-01

These images of Canada's Quebec province were acquired by the Multi-angle Imaging SpectroRadiometer on March 4, 2001. The region's forests are a mixture of coniferous and hardwood trees, and 'sugar-shack' festivities are held at this time of year to celebrate the beginning of maple syrup production. The large river visible in the images is the northeast-flowing St. Lawrence. The city of Montreal is located near the lower left corner, and Quebec City, at the upper right, is near the mouth of the partially ice-covered St. Lawrence Seaway.

Both spectral and angular information are retrieved for every scene observed by MISR. The left-hand image was acquired by the instrument's vertical-viewing (nadir) camera, and is a false-color spectral composite from the near-infrared, red, and blue bands. The right-hand image is a false-color angular composite using red band data from the 60-degree backward-viewing, nadir, and 60-degree forward-viewing cameras. In each case, the individual channels of data are displayed as red, green, and blue, respectively.

Much of the ground remains covered or partially covered with snow. Vegetation appears red in the left-hand image because of its high near-infrared brightness. In the multi-angle composite, vegetated areas appear in shades of green because they are brighter at nadir, possibly as a result of an underlying blanket of snow which is more visible from this direction. Enhanced forward scatter from the smooth water surface results in bluer hues, whereas urban areas look somewhat orange, possibly due to the effect of vertical structures which preferentially backscatter sunlight.

The data were acquired during Terra orbit 6441, and cover an area measuring 275 kilometers x 310 kilometers.

MISR was built and is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

An assessment of the Height Above Nearest Drainage terrain descriptor for the thematic enhancement of automatic SAR-based flood monitoring services

NASA Astrophysics Data System (ADS)

Chow, Candace; Twele, André; Martinis, Sandro

2016-10-01

Flood extent maps derived from Synthetic Aperture Radar (SAR) data can communicate spatially-explicit information in a timely and cost-effective manner to support disaster management. Automated processing chains for SAR-based flood mapping have the potential to substantially reduce the critical time delay between the delivery of post-event satellite data and the subsequent provision of satellite derived crisis information to emergency management authorities. However, the accuracy of SAR-based flood mapping can vary drastically due to the prevalent land cover and topography of a given scene. While expert-based image interpretation with the consideration of contextual information can effectively isolate flood surface features, a fully-automated feature differentiation algorithm mainly based on the grey levels of a given pixel is comparatively more limited for features with similar SAR-backscattering characteristics. The inclusion of ancillary data in the automatic classification procedure can effectively reduce instances of misclassification. In this work, a near-global `Height Above Nearest Drainage' (HAND) index [10] was calculated with digital elevation data and drainage directions from the HydroSHEDS mapping project [2]. The index can be used to separate flood-prone regions from areas with a low probability of flood occurrence. Based on the HAND-index, an exclusion mask was computed to reduce water look-alikes with respect to the hydrologictopographic setting. The applicability of this near-global ancillary data set for the thematic improvement of Sentinel-1 and TerraSAR-X based services for flood and surface water monitoring has been validated both qualitatively and quantitatively. Application of a HAND-based exclusion mask resulted in improvements to the classification accuracy of SAR scenes with high amounts of water look-alikes and considerable elevation differences.

Carbide-Derived Carbons with Tunable Porosity Optimized for Hydrogen Storage

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fisher, John E.; Gogotsi, Yury; Yildirim, Taner

2010-01-07

On-board hydrogen storage is a key requirement for fuel cell-powered cars and trucks. Porous carbon-based materials can in principle adsorb more hydrogen per unit weight at room temperature than liquid hydrogen at -176 oC. Achieving this goal requires interconnected pores with very high internal surface area, and binding energies between hydrogen and carbon significantly enhanced relative to H2 on graphite. In this project a systematic study of carbide-derived carbons, a novel form of porous carbon, was carried out to discover a high-performance hydrogen sorption material to meet the goal. In the event we were unable to improve on the statemore » of the art in terms of stored hydrogen per unit weight, having encountered the same fundamental limit of all porous carbons: the very weak interaction between H2 and the carbon surface. On the other hand we did discover several strategies to improve storage capacity on a volume basis, which should be applicable to other forms of porous carbon. Further discoveries with potentially broader impacts include • Proof that storage performance is not directly related to pore surface area, as had been previously claimed. Small pores (< 1.5 nm) are much more effective in storing hydrogen than larger ones, such that many materials with large total surface areas are sub-par performers. • Established that the distribution of pore sizes can be controlled during CDC synthesis, which opens the possibility of developing high performance materials within a common family while targeting widely disparate applications. Examples being actively pursued with other funding sources include methane storage, electrode materials for batteries and supercapacitors with record high specific capacitance, and perm-selective membranes which bind cytokines for control of infections and possibly hemodialysis filters.« less

Retrieval and Validation of aerosol optical properties from AHI measurements: impact of surface reflectance assumption

NASA Astrophysics Data System (ADS)

Lim, H.; Choi, M.; Kim, J.; Go, S.; Chan, P.; Kasai, Y.

2017-12-01

This study attempts to retrieve the aerosol optical properties (AOPs) based on the spectral matching method, with using three visible and one near infrared channels (470, 510, 640, 860nm). This method requires the preparation of look-up table (LUT) approach based on the radiative transfer modeling. Cloud detection is one of the most important processes for guaranteed quality of AOPs. Since the AHI has several infrared channels, which are very advantageous for cloud detection, clouds can be removed by using brightness temperature difference (BTD) and spatial variability test. The Yonsei Aerosol Retrieval (YAER) algorithm is basically utilized on a dark surface, therefore a bright surface (e.g., desert, snow) should be removed first. Then we consider the characteristics of the reflectance of land and ocean surface using three visible channels. The known surface reflectivity problem in high latitude area can be solved in this algorithm by selecting appropriate channels through improving tests. On the other hand, we retrieved the AOPs by obtaining the visible surface reflectance using NIR to normalized difference vegetation index short wave infrared (NDVIswir) relationship. ESR tends to underestimate urban and cropland area, we improved the visible surface reflectance considering urban effect. In this version, ocean surface reflectance is using the new cox and munk method which considers ocean bidirectional reflectance distribution function (BRDF). Input of this method has wind speed, chlorophyll, salinity and so on. Based on validation results with the sun-photometer measurement in AErosol Robotic NETwork (AERONET), we confirm that the quality of Aerosol Optical Depth (AOD) from the YAER algorithm is comparable to the product from the Japan Aerospace Exploration Agency (JAXA) retrieval algorithm. Our future update includes a consideration of improvement land surface reflectance by hybrid approach, and non-spherical aerosols. This will improve the quality of YAER algorithm more, particularly retrieval for the dust particle over the bright surface in East Asia.

Identifying factors of comfort in using hand tools.

PubMed

Kuijt-Evers, L F M; Groenesteijn, L; de Looze, M P; Vink, P

2004-09-01

To design comfortable hand tools, knowledge about comfort/discomfort in using hand tools is required. We investigated which factors determine comfort/discomfort in using hand tools according to users. Therefore, descriptors of comfort/discomfort in using hand tools were collected from literature and interviews. After that, the relatedness of a selection of the descriptors to comfort in using hand tools was investigated. Six comfort factors could be distinguished (functionality, posture and muscles, irritation and pain of hand and fingers, irritation of hand surface, handle characteristics, aesthetics). These six factors can be classified into three meaningful groups: functionality, physical interaction and appearance. The main conclusions were that (1) the same descriptors were related to comfort and discomfort in using hand tools, (2) descriptors of functionality are most related to comfort in using hand tools followed by descriptors of physical interaction and (3) descriptors of appearance become secondary in comfort in using hand tools.

Analysis of CO2 convection mechanisms associated to surface heating, by combining remote sensing data and in situ measurements

NASA Astrophysics Data System (ADS)

Tello, Marivi; Curcoll, Roger; Font, Anna; Morgu, Josep Anton; Rod, Xavier

Assessing the mechanisms involved in the variability of carbon fluxes is crucial for the under-standing of the changing earth dynamics. In that sense, the aim of this work is to analyze CO2 convection mechanisms at a regional scale in the boundary layer and the lower troposphere by means of cross correlation of land surface temperature data, radio-soundings, wind speeds and in situ measurements of CO2 atmospheric mixing ratios. Since data is easier to acquire, ground level horizontal CO2 fluxes have been widely studied. In the contrary, vertical ones are still subject to uncertainties, even if they are necessary to understand 3D CO2 variability in the atmosphere. In particular, this paper focuses on the relationship between surface heating, convection and CO2 concentrations at different heights and, more generally, on the energy transfer between the surface and the air. The monitored area corresponds to a region on the North Eastern Iberian Peninsula, mainly devoted to agricultural activities. Different types of land covers are observed. On the one hand, in situ data has been collected by several flights during 2007 along the parallel 42o N following the "Crown" aircraft sampling approach [1] that integrates CO2 data obtained through horizontal transects and vertical profiles. This particular configuration is especially well suited for the evaluation of both horizontal and vertical CO2 fluxes. On the other hand, the radiometric land surface temperatures are obtained from the MODIS instrument onboard the Terra and the Aqua satellites. Besides, a flight campaign with an airborne sensor along the same transect in the parallel 42o N has been proposed in the scope of the MIDAS-6 project recently submitted. This project plans to improve soil moisture and ocean salinity products of the SMOS sensor recently launched and to demonstrate its applications. This will allow the study of moisture patterns in the monitored area at two different scales: that of the data collected by the airborne sensor and the coarser one of the data from spaceborne radiometer. Since soil moisture intervenes in the evaporation rate, it is closely related to the sensible heat flux. Hence, the availability of surface soil moisture data will permit a deeper knowledge of the mechanisms involved in the CO2 vertical gradients in the lower troposphere. [1] Font, A., J. A. Morgué X. Rodé (2008), Atmospheric CO2 in situ measurements: Two ı, examples of Crown Design flights in NE Spain, J. Geophys. Research, 113, D12308.

Surgical wound care - closed

MedlinePlus

... dressing. Wash your hands with soap and warm water. Also clean under your nails. Rinse, then dry your hands with a clean towel . Make sure you have all the supplies handy. Have a clean work surface. Remove the ...

The effects of shape crowding on grasping.

PubMed

Chen, Juan; Jayawardena, Sanasi; Goodale, Melvyn Alan

2015-03-10

Crowding refers to the deleterious effect of nearby objects on the identification of a target in the peripheral visual field. A recent study (Chen, Sperandio, & Goodale, 2015) showed that when a three-dimensional (3D) disk was crowded by disks of different sizes, participants could scale their grip aperture to the size of the target, even when they could not perceive its size. It is still unclear, however, whether or not grasping can also escape to some degree the crowding of other object features, such as shape. To test this, we presented 3D rectangular blocks in isolation or crowded by other blocks in the periphery. The target and flanking blocks had the same surface area but different dimensions. Participants were required either to grasp the target block across its width or to estimate its width. We found that, consistent with what we observed earlier with size, participants can also scale their grasp to the width of the target block even when they could not perceive its width. To further explore whether or not the effect of crowding on grasping depends on how proficient people are with their right hand, we had right-handed participants perform the same test but with their left hand. We found that left-hand grasping did not escape the crowding effect on shape perception at all. Taken together, our results suggest that people can also use invisible shape information to guide actions and that this ability depends on the proficiency of the action. © 2015 ARVO.

Norovirus Transmission between Hands, Gloves, Utensils, and Fresh Produce during Simulated Food Handling

PubMed Central

Aho, E.; Mikkelä, A.; Ranta, J.; Tuominen, P.; Rättö, M.; Maunula, L.

2014-01-01

Human noroviruses (HuNoVs), a leading cause of food-borne gastroenteritis worldwide, are easily transferred via ready-to-eat (RTE) foods, often prepared by infected food handlers. In this study, the transmission of HuNoV and murine norovirus (MuNoV) from virus-contaminated hands to latex gloves during gloving, as well as from virus-contaminated donor surfaces to recipient surfaces after simulated preparation of cucumber sandwiches, was inspected. Virus transfer was investigated by swabbing with polyester swabs, followed by nucleic acid extraction from the swabs with a commercial kit and quantitative reverse transcription-PCR. During gloving, transfer of MuNoV dried on the hand was observed 10/12 times. HuNoV, dried on latex gloves, was disseminated to clean pairs of gloves 10/12 times, whereas HuNoV without drying was disseminated 11/12 times. In the sandwich-preparing simulation, both viruses were transferred repeatedly to the first recipient surface (left hand, cucumber, and knife) during the preparation. Both MuNoV and HuNoV were transferred more efficiently from latex gloves to cucumbers (1.2% ± 0.6% and 1.5% ± 1.9%) than vice versa (0.7% ± 0.5% and 0.5% ± 0.4%). We estimated that transfer of at least one infective HuNoV from contaminated hands to the sandwich prepared was likely to occur if the hands of the food handler contained 3 log10 or more HuNoVs before gloving. Virus-contaminated gloves were estimated to transfer HuNoV to the food servings more efficiently than a single contaminated cucumber during handling. Our results indicate that virus-free food ingredients and good hand hygiene are needed to prevent HuNoV contamination of RTE foods. PMID:24951789

Inland notches micromorphology

NASA Astrophysics Data System (ADS)

Brook, Anna; Ben-Binyamin, Atzmon; Shtober-Zisu, Nurit

2017-04-01

Inland notches are well known phenomenon in Israel and can be found mostly along the mountainous backbone, developed in hard limestone or dolomite rocks within the Mediterranean climate zone and up to the desert fringe. LiDAR technology presents an opportunity to study the fine scale rock surface within the notch and its texture patterns. De-trending of the LiDAR reconstructed DEM to a local trend, surface roughness, was achieved by fitting a normalized surface to all measured ground points within the roughness neighborhood. Micro-topography plays an important role for modelling geomorphology dynamics, resulting in improved estimates for micro stream lines network and topographic erosion as well as mineral accumulation or deposition. Clearly, dissolution occurs whenever rock and solvent meet; thus water and moisture's crucial role in the decay of carbonate rocks results in texture and roughness variability. Study aims is to generate high resolution normalized DEM models using a terrestrial LiDAR, redefining the texture and roughness within the notch while assessing weathering processes caused by water. Plan curvature is the second derivative of slope taken perpendicular to its direction. It influences convergence and divergence of flow and it emphasizes the ridges and valleys across the surface. Concaved classified areas were tested against all planar curvature areas to distinguish them as unique areas based on their texture co-occurrence measures (GLCM). Overall negative curvature pixels show poor separability, in both TD and JM separation tests, while classes of curvature degree describe a positive trend showing medium and high concavity as unique areas. Study aims to link classified areas as the basic micro infrastructure for water flow, potential runoff flow and further accumulation of minerals. On the other hand, positive values of Plan curvature present the convexity of rock surface to imply diverging flow, thus describing the watershed line within the micro-topography. GLCM texture measure map distinct areas within the notch. Middle section of the notch has uniform texture neighborhood with relatively low mean elevation values (high values for homogeneity and energy). Bottom cavity of notch reveals a more chaotic texture, highlighting the spatial disorder with relatively high mean values. Entropy calculates how random the roughness values are, and as such, high values of this measure, at the cavity's bottom, suggest a potentially rapid erosion or disposition dynamics.

Multi-channel NIRS of the primary motor cortex to discriminate hand from foot activity

NASA Astrophysics Data System (ADS)

Koenraadt, K. L. M.; Duysens, J.; Smeenk, M.; Keijsers, N. L. W.

2012-08-01

The poor spatial resolution of near-infrared spectroscopy (NIRS) makes it difficult to distinguish two closely located cortical areas from each other. Here, a combination of multi-channel NIRS and a centre of gravity (CoG) approach (widely accepted in the field of transcranial magnetic stimulation; TMS) was used to discriminate between closely located cortical areas activated during hand and foot movements. Similarly, the possibility of separating the more anteriorly represented discrete movements from rhythmic movements was studied. Thirteen healthy right-handed subjects performed rhythmic or discrete (‘task’) hand or foot (‘extremity’) tapping. Hemodynamic responses were measured using an 8-channel NIRS setup. For oxyhemoglobin (OHb) and deoxyhemoglobin (HHb), a CoG was determined for each condition using the mean hemodynamic responses and the coordinates of the channels. Significant hemodynamic responses were found for hand and foot movements. Based on the HHb responses, the NIRS-CoG of hand movements was located 0.6 cm more laterally compared to the NIRS-CoG of foot movements. For OHb responses no difference in NIRS-CoG was found for ‘extremity’ nor for ‘task’. This is the first NIRS study showing hemodynamic responses for isolated foot movements. Furthermore, HHb responses have the potential to be used in multi-channel NIRS experiments requiring differential activation of motor cortex areas linked to either hand or foot movements.

Influence of geology on arsenic concentrations in ground and surface water in central Lesvos, Greece.

PubMed

Aloupi, Maria; Angelidis, Michael O; Gavriil, Apostolos M; Koulousaris, Michael; Varnavas, Soterios P

2009-04-01

The occurrence of As was studied in groundwater used for human consumption and irrigation, in stream water and sediments and in water from thermal springs in the drainage basin of Kalloni Gulf, island of Lesvos, Greece, in order to investigate the potential influence of the geothermal field of Polichnitos-Lisvori on the ground and surface water systems of the area. Total dissolved As varied in the range <0.7-88.3 microg L(-1) in groundwater, 41.1-90.7 microg L(-1) in thermal spring water and 0.4-13.2 microg L(-1) in stream water, whereas As concentrations in stream sediments varied between 2.0-21.9 mg kg(-1). Four out of 31 groundwater samples exceeded the EC standard of 10 microg L(-1). The survey revealed an enrichment in both surface and groundwater hydrological systems in the northern part of the area (average concentrations of As in groundwater, stream water and stream sediment: 8.0 microg L(-1), 8.8 microg L(-1) and 15.0 mg kg(-1) respectively), in association with the volcanic bedrocks, while lower As concentrations were found in the eastern part (average concentrations in groundwater, stream water and stream sediment: 2.9 microg L(-1), 1.7 microg L(-1) and 5.9 mg kg(-1) respectively), which is dominated by ophiolitic ultramafic formations. The variation of As levels between the different parts of the study area suggests that local geology exerts a determinant influence on As geochemical behaviour. On the other hand, the geothermal activity manifested in the area of Polichnitos-Lisvori does not affect the presence of As in groundwater and streams.

Differential involvement of cortical and cerebellar areas using dominant and nondominant hands: An FMRI study

PubMed Central

Pardini, Matteo; Samson, Rebecca S.; D'Angelo, Egidio; Friston, Karl J.; Toosy, Ahmed T.; Gandini Wheeler‐Kingshott, Claudia A.M.

2015-01-01

Abstract Motor fMRI studies, comparing dominant (DH) and nondominant (NDH) hand activations have reported mixed findings, especially for the extent of ipsilateral (IL) activations and their relationship with task complexity. To date, no study has directly compared DH and NDH activations using an event‐related visually guided dynamic power‐grip paradigm with parametric (three) forces (GF) in healthy right‐handed subjects. We implemented a hierarchical statistical approach aimed to: (i) identify the main effect networks engaged when using either hand; (ii) characterise DH/NDH responses at different GFs; (iii) assess contralateral (CL)/IL‐specific and hemisphere‐specific activations. Beyond confirming previously reported results, this study demonstrated that increasing GF has an effect on motor response that is contextualised also by the use of DH or NDH. Linear analysis revealed increased activations in sensorimotor areas, with additional increased recruitments of subcortical and cerebellar areas when using the NDH. When looking at CL/IL‐specific activations, CL sensorimotor areas and IL cerebellum were activated with both hands. When performing the task with the NDH, several areas were also recruited including the CL cerebellum. Finally, there were hand‐side‐independent activations of nonmotor‐specific areas in the right and left hemispheres, with the right hemisphere being involved more extensively in sensori‐motor integration through associative areas while the left hemisphere showing greater activation at higher GF. This study shows that the functional networks subtending DH/NDH power‐grip visuomotor functions are qualitatively and quantitatively distinct and this should be taken into consideration when performing fMRI studies, particularly when planning interventions in patients with specific impairments. Hum Brain Mapp 36:5079–5100, 2015. © 2015 Wiley Periodicals, Inc. PMID:26415818

Surface water, groundwater and unified 3D-crack network as a triple coupling dynamic system for a river watershed functioning - manifestation in catastrophic floods

NASA Astrophysics Data System (ADS)

Trifonova, Tatiana; Tulenev, Nikita; Trifonov, Dmitriy; Arakelian, Sergei

2014-05-01

1. Surface water and groundwater interaction model under conditions of huge level of precipitation in catastrophic floods and mudflows for mountain river watershed is introduced. Seismic processes and volcanic activity impact on the formation of disastrous floods due to dramatic change of the pressure field in groundwater horizons, is under discussion for such a triple coupling system, i.e. surface water - groundwater - crack network. Under the conception we analyze recent (2013) catastrophic water events: the catastrophic floods in Western Europe (May-June, 2013), in the Amur river basin, Russia/China (Aug.-Sept, 2013) and in Colorado, USA (Sept. 12-15,2013). In addition, a separate analysis is carried out for debris event in the Krimsk-city, Caucasus (Krasnodar) region, Russia (July 06-07, 2012). 2. There is a group of problems determined by dramatic discrepancies in water mass balance and other vital parameters, on the one hand, by estimation for different types of atmospheric precipitation (both torrential rain and continuous precipitations) and, on the other hand, for observable natural water events (i.e. catastrophic floods and/or mudflows/debris) on concrete territory. Analysis of many facts result in conclusion that we have the hard comparable/coincidence parameters under traditional conception for discussed events as an isolated/closed (river + rain) runoff-system. In contrast, the reasonable point of view does exist if we take into account the contribution of extra water source, which should be localized in river channel, i.e. functioning of open [(river + rain) + groundwater] flow-system has a principal meaning to understand the events occurrence. 3. The analysis and modeling for the events are carried out by us taking into account the following databases: (i) groundwater map dislocation, it resources and flow balance in studied areas, especially near the land surface being unstable in hydrological sense by many reasons, as well due to heavy rain stimulating a trigger mechanism for releasing of groundwater; (ii) the crackness/fracturing structure as a characteristic property for all rocks, being dissecting by totality of cracks/fissures and along which (in the case when a good development crack becomes a fault) a vertical and/or lateral movement (of both groundwater and surface water mass) occurs as a result of excessive strain; (iii) areas of formation and modification in time of groundwater transit system, and especially the modalities for it exit on surface by different factors including tectonic processes under adjustable conditions for both localization of earthquake epicenters/volcanos activity areas and occurring floods in respect of propagating of seismic waves and dislocation of border for lithospheric plates/magma objects in the river basin region; (iv) the way of distribution over surface for water flows/fronts in the further, which can be described by nonlinear hydrodynamic approach, e.g. by different classes of solutions for Korteweg-de Vries equation, associated with observable natural phenomena. 4. Monitoring in dynamics of state of hydrostatic/hydrodynamic pressures in underground aquifers (e.g. by artesian wells in comparison with two databases: before and after the events) is an important factor in assessing of acceptable risk for the events. Combining it with monitoring of seismic activity should allow to make a more detailed forecasting and zoning of potentially dangerous areas for such natural disasters.

Internal variability of fine-scale components of meteorological fields in extended-range limited-area model simulations with atmospheric and surface nudging

NASA Astrophysics Data System (ADS)

Separovic, Leo; Husain, Syed Zahid; Yu, Wei

2015-09-01

Internal variability (IV) in dynamical downscaling with limited-area models (LAMs) represents a source of error inherent to the downscaled fields, which originates from the sensitive dependence of the models to arbitrarily small modifications. If IV is large it may impose the need for probabilistic verification of the downscaled information. Atmospheric spectral nudging (ASN) can reduce IV in LAMs as it constrains the large-scale components of LAM fields in the interior of the computational domain and thus prevents any considerable penetration of sensitively dependent deviations into the range of large scales. Using initial condition ensembles, the present study quantifies the impact of ASN on IV in LAM simulations in the range of fine scales that are not controlled by spectral nudging. Four simulation configurations that all include strong ASN but differ in the nudging settings are considered. In the fifth configuration, grid nudging of land surface variables toward high-resolution surface analyses is applied. The results show that the IV at scales larger than 300 km can be suppressed by selecting an appropriate ASN setup. At scales between 300 and 30 km, however, in all configurations, the hourly near-surface temperature, humidity, and winds are only partly reproducible. Nudging the land surface variables is found to have the potential to significantly reduce IV, particularly for fine-scale temperature and humidity. On the other hand, hourly precipitation accumulations at these scales are generally irreproducible in all configurations, and probabilistic approach to downscaling is therefore recommended.

Expansion of Smartwatch Touch Interface from Touchscreen to Around Device Interface Using Infrared Line Image Sensors

PubMed Central

Lim, Soo-Chul; Shin, Jungsoon; Kim, Seung-Chan; Park, Joonah

2015-01-01

Touchscreen interaction has become a fundamental means of controlling mobile phones and smartwatches. However, the small form factor of a smartwatch limits the available interactive surface area. To overcome this limitation, we propose the expansion of the touch region of the screen to the back of the user’s hand. We developed a touch module for sensing the touched finger position on the back of the hand using infrared (IR) line image sensors, based on the calibrated IR intensity and the maximum intensity region of an IR array. For complete touch-sensing solution, a gyroscope installed in the smartwatch is used to read the wrist gestures. The gyroscope incorporates a dynamic time warping gesture recognition algorithm for eliminating unintended touch inputs during the free motion of the wrist while wearing the smartwatch. The prototype of the developed sensing module was implemented in a commercial smartwatch, and it was confirmed that the sensed positional information of the finger when it was used to touch the back of the hand could be used to control the smartwatch graphical user interface. Our system not only affords a novel experience for smartwatch users, but also provides a basis for developing other useful interfaces. PMID:26184202

Cortical correlates of neuromotor development in healthy children.

PubMed

Garvey, M A; Ziemann, U; Bartko, J J; Denckla, M B; Barker, C A; Wassermann, E M

2003-09-01

To examine the relationship between acquisition of fine motor skills in childhood and development of the motor cortex. We measured finger tapping speed and mirror movements in 43 healthy right-handed subjects (6-26 years of age). While recording surface electromyographic activity from right and left first dorsal interosseus, we delivered focal transcranial magnetic stimulation (TMS) over the hand areas of each motor cortex. We measured motor evoked potential (MEP) threshold, and ipsilateral (iSP) and contralateral (CSP) silent periods. As children got older, finger speeds got faster, MEP threshold decreased, iSP duration increased and latency decreased. Finger tapping speed got faster as motor thresholds and iSP latency decreased, but was unrelated to CSP duration. In all subjects right hemisphere MEP thresholds were higher than those on the left and duration of right hemisphere CSP was longer than that on the left. Children under 10 years of age had higher left hand mirror movement scores, and fewer left hemisphere iSPs which were of longer duration. Maturation of finger tapping skills is closely related to developmental changes in the motor threshold and iSP latency. Studies are warranted to explore the relationship between these measures and other neuromotor skills in children with motor disorders. TMS can provide important insights into certain functional aspects of neurodevelopment in children.

A repeatable geometric morphometric approach to the analysis of hand entheseal three-dimensional form.

PubMed

Karakostis, Fotios Alexandros; Hotz, Gerhard; Scherf, Heike; Wahl, Joachim; Harvati, Katerina

2018-05-01

The purpose of this study was to put forth a precise landmark-based technique for reconstructing the three-dimensional shape of human entheseal surfaces, to investigate whether the shape of human entheses is related to their size. The effects of age-at-death and bone length on entheseal shapes were also assessed. The sample comprised high-definition three-dimensional models of three right hand entheseal surfaces, which correspond to 45 male adult individuals of known age. For each enthesis, a particular landmark configuration was introduced, whose precision was tested both within and between observers. The effect of three-dimensional size, age-at-death, and bone length on shape was investigated through shape regression. The method presented high intra-observer and inter-observer repeatability. All entheses showed significant allometry, with the area of opponens pollicis demonstrating the most substantial relationship. This was particularly due to variation related to its proximal elongated ridge. The effect of age-at-death and bone length on entheses was limited. The introduced methodology can set a reliable basis for further research on the factors affecting entheseal shape. Using both size and shape, variables can provide further information on entheseal variation and its biomechanical implications. The low entheseal variation by age verifies that specimens under 50 years of age are not substantially affected by age-related changes. The lack of correlation between entheseal shape and bone length or age implies that other factors may regulate entheseal surfaces. Future research should focus on multivariate shape patterns among entheses and their association with occupation. © 2018 Wiley Periodicals, Inc.

Bacteriological quality and food safety in a Brazilian school food program.

PubMed

Nagla Chaves Trindade, Samara; Silva Pinheiro, Julia; Gonçalves de Almeida, Héllen; Carvalho Pereira, Keyla; de Souza Costa Sobrinho, Paulo

2014-01-01

Food safety is a critical issue in school food program. This study was conducted to assess the bacteriological quality and food safety practices of a municipal school food program (MSFP) in Jequitinhonha Valley, Brazil. A checklist based on good manufacturing practices (GMP) for food service was used to evaluate food safety practices. Samples from foods, food contact surfaces, the hands of food handlers, the water supply and the air were collected to assess bacteriological quality in establishments that comprise the MSFP. Nine (81.8%) establishments were classified as poor quality and two (18.2%) as medium quality. Neither Salmonella nor Listeria monocytogenes were detected in food samples. Coliforms, Escherichia coli and Staphylococcus aureus were detected in 36 (52.9%), 1 (1.5%) and 22 (32.4%) of the food samples and in 24 (40.7%), 2 (3.3%) and 13 (22.0%) of the food contact surfaces, respectively. The counts of coliforms and Staphylococcus aureus ranged from 1 to 5.0 and 1 to 5.1 log CFU/g of food, respectively. The mean aerobic mesophilic bacteria count was 3.1 log CFU/100 cm2 of surface area. Coliforms, E. coli and S. aureus were detected on the hands of 33 (73.3%), 1 (2.2%) and 36 (80%) food handlers, respectively. With regard to air quality, all the establishments had an average aerobic mesophilic count above 1.6 log CFU/cm2/week. The results indicate the need to modify the GMP used in food service in MSFP in relation to food safety, particularly because children served in these establishments are often the most socially vulnerable.

Legally compatible design of digital dactyloscopy in future surveillance scenarios

NASA Astrophysics Data System (ADS)

Pocs, Matthias; Schott, Maik; Hildebrandt, Mario

2012-06-01

Innovation in multimedia systems impacts on our society. For example surveillance camera systems combine video and audio information. Currently a new sensor for capturing fingerprint traces is being researched. It combines greyscale images to determine the intensity of the image signal, on one hand, and topographic information to determine fingerprint texture on a variety of surface materials, on the other. This research proposes new application areas which will be analyzed from a technical-legal view point. It assesses how technology design can promote legal criteria of German and European privacy and data protection. For this we focus on one technology goal as an example.

Toroid Joining Gun For Fittings And Couplings

NASA Technical Reports Server (NTRS)

Fox, Robert L.; Swaim, Robert J.; Johnson, Samuel D.; Buckley, John D.; Copeland, Carl E.; Coultrip, Robert H.; Johnston, David F.; Phillips, William M.

1992-01-01

Hand-held gun used to join metal heat-to-shrink couplings. Uses magnetic induction (eddy currents) to produce heat in metal coupling, and thermocouple to measure temperature and signals end of process. Gun, called "toroid joining gun" concentrates high levels of heat in localized areas. Reconfigured for use on metal heat-to-shrink fitting and coupling applications. Provides rapid heating, operates on low power, lightweight and portable. Safe for use around aircraft fuel and has no detrimental effects on surrounding surfaces or objects. Reliable in any environment and under all weather conditions. Gun logical device for taking full advantage of capabilities of new metal heat-to-shrink couplings and fittings.

FUNCTIONAL RECOVERY FOLLOWING MOTOR CORTEX LESIONS IN NON-HUMAN PRIMATES: EXPERIMENTAL IMPLICATIONS FOR HUMAN STROKE PATIENTS

PubMed Central

Darling, Warren G.; Pizzimenti, Marc A.; Morecraft, Robert J.

2013-01-01

This review discusses selected classical works and contemporary research on recovery of contralesional fine hand motor function following lesions to motor areas of the cerebral cortex in non-human primates. Findings from both the classical literature and contemporary studies show that lesions of cortical motor areas induce paresis initially, but are followed by remarkable recovery of fine hand/digit motor function that depends on lesion size and post-lesion training. Indeed, in recent work where considerable quantification of fine digit function associated with grasping and manipulating small objects has been observed, very favorable recovery is possible with minimal forced use of the contralesional limb. Studies of the mechanisms underlying recovery have shown that following small lesions of the digit areas of primary motor cortex (M1), there is expansion of the digit motor representations into areas of M1 that did not produce digit movements prior to the lesion. However, after larger lesions involving the elbow, wrist and digit areas of M1, no such expansion of the motor representation was observed, suggesting that recovery was due to other cortical or subcortical areas taking over control of hand/digit movements. Recently, we showed that one possible mechanism of recovery after lesion to the arm areas of M1 and lateral premotor cortex is enhancement of corticospinal projections from the medially located supplementary motor area (M2) to spinal cord laminae containing neurons which have lost substantial input from the lateral motor areas and play a critical role in reaching and digit movements. Because human stroke and brain injury patients show variable, and usually poorer, recovery of hand motor function than that of nonhuman primates after motor cortex damage, we conclude with a discussion of implications of this work for further experimentation to improve recovery of hand function in human stroke patients. PMID:21960307

Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files

PubMed Central

Raisingani, Deepak; Mathur, Rachit; Madan, Nidha; Visnoi, Suchita

2016-01-01

Aim To evaluate the incidence of apical crack initiation during canal preparation with stainless steel K-files and hand protaper files (in vitro study). Materials and methods Sixty extracted mandibular premo-lar teeth are randomly selected and embedded in an acrylic tube filled with autopolymerizing resin. A baseline image of the apical surface of each specimen was recorded under a digital microscope (80×). The cervical and middle thirds of all samples were flared with #2 and #1 Gates-Glidden (GG) drills, and a second image was recorded. The teeth were randomly divided into four groups of 15 teeth each according to the file type (hand K-file and hand-protaper) and working length (WL) (instrumented at WL and 1 mm less than WL). Final image after dye penetration and photomicrograph of the apical root surface were digitally recorded. Results Maximum numbers of cracks were observed with hand protaper files compared with hand K-file at the WL and 1 mm short of WL. Chi-square testing revealed a highly significant effect of WL on crack formation at WL and 1 mm short of WL (p = 0.000). Conclusion Minimum numbers of cracks at WL and 1 mm short of WL were observed with hand K-file and maximum with hand protaper files. How to cite this article Soni D, Raisingani D, Mathur R, Madan N, Visnoi S. Incidence of Apical Crack Initiation during Canal Preparation using Hand Stainless Steel (K-File) and Hand NiTi (Protaper) Files. Int J Clin Pediatr Dent 2016;9(4):303-307. PMID:28127160

A comparison and evaluation between ICESat/GLAS altimetry and mean sea level in Thailand

NASA Astrophysics Data System (ADS)

Naksen, Didsaphan; Yang, Dong Kai

2015-10-01

Surface elevation is one of the importance information for GIS. Usually surface elevation can acquired from many sources such as satellite imageries, aerial photograph, SAR data or LiDAR by photogrammetry, remote sensing methodology. However the most trust information describe the actual surface elevation is Leveling from terrestrial survey. Leveling is giving the highest accuracy but in the other hand is also long period process spending a lot of budget and resources, moreover the LiDAR technology is new era to measure surface elevation. ICESat/GLAS is spaceborne LiDAR platform, a scientific satellite lunched by NASA in 2003. The study area was located at the middle part of Thailand between 12. ° - 14° North and 98° -100° East Latitude and Longitude. The main idea is to compare and evaluate about elevation between ICESat/GLAS Altimetry and mean sea level of Thailand. Data are collected from various sources, including the ICESat/GLAS altimetry data product from NASA, mean sea level from Royal Thai Survey Department (RTSD). For methodology, is to transform ICESat GLA14 from TOPX/Poseidon-Jason ellipsoid to WGS84 ellipsoid. In addition, ICESat/GLAS altimetry that extracted form centroid of laser footprint and mean sea level were compared and evaluated by 1st Layer National Vertical Reference Network. The result is shown that generally the range of elevation between ICESat/GLAS and mean sea level is wildly from 0. 8 to 25 meters in study area.

Application of 2D electrical resistivity imaging and cone penetration test (CPT) to assess the harzadous effect of near surface water on foundations in Lagos Nigeria

NASA Astrophysics Data System (ADS)

Adewoyin, O. O.; Joshua, E. O.; Akinyemi, M. L.; Omeje, M.; Joel, E. S.

2017-05-01

Adequate information on the condition of the subsurface is very important for site evaluation for engineering purposes. In this study two dimensional (2D) geoelectrical resistivity survey and cone penetration tests were conducted to study the hazardous effect of excess near surface water on the foundation of building in a reclaimed land located at Victoria Island area of Lagos State. The results of the inverted 2D geoelectrical resistivity data revealed three distinct geoelectrical layers characterized by low to moderate electrical resistivity of 2.23 and 129Ωm and 9.46 to 636Ωm respectively. The topsoil is characterized by wet sandy soil, which is underlain by sandy clay and banded at the below by a geologic formation of low resistivity which is suspected to be clay. The clay material may be responsible for the excess water retention observed in the area. The CPT method on the other hand revealed a geological formation of low resistance to penetration between 2-3 kg/cm2 from the topsoil to a depth of 7 m, which may be the effect of excess water in the near surface. This study revealed that the foundation of building may not be founded directly on the soil in any reclaimed land as this may result in collapse as a result of upward migration of water to the near surface.

Our initial learning curve in the enzymatic debridement of severely burned hands-Management and pit falls of initial treatments and our development of a post debridement wound treatment algorithm.

PubMed

Schulz, A; Perbix, W; Shoham, Y; Daali, S; Charalampaki, C; Fuchs, P C; Schiefer, J

2017-03-01

Excisional surgical debridement (SD) is still the gold standard in the treatment of deeply burned hands, though the intricate anatomy is easily damaged. Previous studies demonstrated that enzymatic debridement with the bromelain debriding agent NexoBrid ® (EDNX) is more selective and thus can preserve viable tissue with excellent outcome results. So far no method paper has been published presenting different treatment algorithms in this new field. Therefore our aim was to close this gap by presenting our detailed learning curve in EDNX of deeply burned hands. We conducted a single-center prospective observational clinical trial treating 20 patients with deeply burned hands with EDNX. Different anaesthetic procedures, debridement and wound treatment algorithms were compared and main pitfalls described. EDNX was efficient in 90% of the treatments though correct wound bed evaluation was challenging and found unusual compared to SD. Post EDNX surprisingly the majority of the burn surface area was found overestimated (18 wounds). Finally we simplified our process and reduced treatment costs by following a modified treatment algorithm and treating under plexus anaesthesia bedside through a single nurse and one burn surgeon solely. Suprathel ® could be shown to be an appropriate dressing for wound treatment after EDNX. Complete healing (less 5% rest defect) was achieved at an average of day 28. EDNX in deep burned hands is promising regarding handling and duration of the treatment, efficiency and selectivity of debridement, healing potential and early rehabilitation. Following our treatment algorithm EDNX can be performed easily and even without special knowledge in burn wound depth evaluation. Copyright © 2016 Elsevier Ltd and ISBI. All rights reserved.

Efficacy of ProTaper universal retreatment files in removing filling materials during root canal retreatment.

PubMed

Giuliani, Valentina; Cocchetti, Roberto; Pagavino, Gabriella

2008-11-01

The aim of this study was to evaluate the efficacy of the ProTaper Universal System rotary retreatment system and of Profile 0.06 and hand instruments (K-file) in the removal of root filling materials. Forty-two extracted single-rooted anterior teeth were selected. The root canals were enlarged with nickel-titanium (NiTi) rotary files, filled with gutta-percha and sealer, and randomly divided into 3 experimental groups. The filling materials were removed with solvent in conjunction with one of the following devices and techniques: the ProTaper Universal System for retreatment, ProFile 0.06, and hand instruments (K-file). The roots were longitudinally sectioned, and the image of the root surface was photographed. The images were captured in JPEG format; the areas of the remaining filling materials and the time required for removing the gutta-percha and sealer were calculated by using the nonparametric one-way Kruskal-Wallis test and Tukey-Kramer tests, respectively. The group that showed better results for removing filling materials was the ProTaper Universal System for retreatment files, whereas the group of ProFile rotary instruments yielded better root canal cleanliness than the hand instruments, even though there was no statistically significant difference. The ProTaper Universal System for retreatment and ProFile rotary instruments worked significantly faster than the K-file. The ProTaper Universal System for retreatment files left cleaner root canal walls than the K-file hand instruments and the ProFile Rotary instruments, although none of the devices used guaranteed complete removal of the filling materials. The rotary NiTi system proved to be faster than hand instruments in removing root filling materials.

Influence on grip of knife handle surface characteristics and wearing protective gloves.

PubMed

Claudon, Laurent

2006-11-01

Ten subjects were asked to apply maximum torques on knife handles with either their bare hand or their hand wearing a Kevlar fibre protective glove. Four knife handles (2 roughnesses, 2 hardnesses) were tested. Surface electromyograms of 6 upper limb and shoulder muscles were recorded and subject opinions on both knife handle hardness and friction in the hand were also assessed. The results revealed the significant influence of wearing gloves (p<0.0001), knife type (p<0.0005) and handle hardness (p<0.005) on the applied torque. Wearing Kevlar fibre gloves greatly increased the torque independently of the other two parameters. Under the bare hand condition, a 90 degrees ShA slightly rough handle provided the greatest torque. Subject opinion agreed with the observed effects on recorded torque values except for the hardness factor, for which a preference for the 70 degrees ShA value over the 90 degrees ShA value emerged.

A Teacher's Science Companion.

ERIC Educational Resources Information Center

Perry, Phyllis J.

The purpose of this guide is to highlight some broad areas in which teachers and other adults have exceptional opportunities to encourage and enjoy teaching children science. Each area in the book provides some hands-on ideas for projects as well as an annotated list of readily available resources that might prove helpful on the topic at hand. The…

Hands-On Classroom Photolithography Laboratory Module to Explore Nanotechnology

ERIC Educational Resources Information Center

Stelick, Scott J.; Alger, William H.; Laufer, Jesse S.; Waldron, Anna M.; Batt, Carl A.

2005-01-01

Nanotechnology is an area of significant interest and can be used as a motivator for students in subject areas including physics, chemistry, and life sciences. A 5X reducer system and associated lesson plan was used to provide students a hands-on exposure to the basic principles of photolithography and microscale circuit fabrication.

Environmental Factors Associated with Norovirus Transmission in Long-Term Care Facilities in South Carolina.

PubMed

Jayasekara, Lalani; Leone, Cortney M; Sharp, Julia; Getty, Morgan

2016-09-01

In the U.S., 60% of norovirus outbreaks are attributed to long-term care facilities (LTCFs). A descriptive study of 26 LTCFs in South Carolina was conducted to determine the presence of environmental factors associated with transmission of human noroviruses. Sanitary conditions in one common area, one staff/visitor bathroom, and the main kitchen were assessed using two audit forms. While surfaces in all kitchens were in good sanitary condition, 23 LTCFs used quaternary ammonium-based sanitizers and three LTCFs used chlorine bleach for kitchen sanitization. All common areas were also clean and in good condition; however, 20 LTCFs had upholstered chairs, and five LTCFs had carpeted floors. Seven facilities used quaternary ammonium-based disinfectants exclusively, whereas six LTCFs used chlorine bleach exclusively, and eight LTCFs used both to disinfect common areas. Seven staff/visitor bathrooms were accessible to residents, and hand washing signage was missing from 10. These results reveal the presence of environmental factors that might facilitate norovirus transmission within LTCFs.

Four-dimensional maps of the human somatosensory system

PubMed Central

Avanzini, Pietro; Abdollahi, Rouhollah O.; Sartori, Ivana; Caruana, Fausto; Pelliccia, Veronica; Casaceli, Giuseppe; Mai, Roberto; Lo Russo, Giorgio; Rizzolatti, Giacomo; Orban, Guy A.

2016-01-01

A fine-grained description of the spatiotemporal dynamics of human brain activity is a major goal of neuroscientific research. Limitations in spatial and temporal resolution of available noninvasive recording and imaging techniques have hindered so far the acquisition of precise, comprehensive four-dimensional maps of human neural activity. The present study combines anatomical and functional data from intracerebral recordings of nearly 100 patients, to generate highly resolved four-dimensional maps of human cortical processing of nonpainful somatosensory stimuli. These maps indicate that the human somatosensory system devoted to the hand encompasses a widespread network covering more than 10% of the cortical surface of both hemispheres. This network includes phasic components, centered on primary somatosensory cortex and neighboring motor, premotor, and inferior parietal regions, and tonic components, centered on opercular and insular areas, and involving human parietal rostroventral area and ventral medial-superior-temporal area. The technique described opens new avenues for investigating the neural basis of all levels of cortical processing in humans. PMID:26976579

Four-dimensional maps of the human somatosensory system.

PubMed

Avanzini, Pietro; Abdollahi, Rouhollah O; Sartori, Ivana; Caruana, Fausto; Pelliccia, Veronica; Casaceli, Giuseppe; Mai, Roberto; Lo Russo, Giorgio; Rizzolatti, Giacomo; Orban, Guy A

2016-03-29

A fine-grained description of the spatiotemporal dynamics of human brain activity is a major goal of neuroscientific research. Limitations in spatial and temporal resolution of available noninvasive recording and imaging techniques have hindered so far the acquisition of precise, comprehensive four-dimensional maps of human neural activity. The present study combines anatomical and functional data from intracerebral recordings of nearly 100 patients, to generate highly resolved four-dimensional maps of human cortical processing of nonpainful somatosensory stimuli. These maps indicate that the human somatosensory system devoted to the hand encompasses a widespread network covering more than 10% of the cortical surface of both hemispheres. This network includes phasic components, centered on primary somatosensory cortex and neighboring motor, premotor, and inferior parietal regions, and tonic components, centered on opercular and insular areas, and involving human parietal rostroventral area and ventral medial-superior-temporal area. The technique described opens new avenues for investigating the neural basis of all levels of cortical processing in humans.

Functional organization of human intraparietal and frontal cortex for attending, looking, and pointing

NASA Technical Reports Server (NTRS)

Astafiev, Serguei V.; Shulman, Gordon L.; Stanley, Christine M.; Snyder, Abraham Z.; Van Essen, David C.; Corbetta, Maurizio

2003-01-01

We studied the functional organization of human posterior parietal and frontal cortex using functional magnetic resonance imaging (fMRI) to map preparatory signals for attending, looking, and pointing to a peripheral visual location. The human frontal eye field and two separate regions in the intraparietal sulcus were similarly recruited in all conditions, suggesting an attentional role that generalizes across response effectors. However, the preparation of a pointing movement selectively activated a different group of regions, suggesting a stronger role in motor planning. These regions were lateralized to the left hemisphere, activated by preparation of movements of either hand, and included the inferior and superior parietal lobule, precuneus, and posterior superior temporal sulcus, plus the dorsal premotor and anterior cingulate cortex anteriorly. Surface-based registration of macaque cortical areas onto the map of fMRI responses suggests a relatively good spatial correspondence between human and macaque parietal areas. In contrast, large interspecies differences were noted in the topography of frontal areas.

Roles of the right temporo-parietal and premotor cortices in self-location and body ownership.

PubMed

Convento, Silvia; Romano, Daniele; Maravita, Angelo; Bolognini, Nadia

2018-06-01

In the rubber hand illusion (RHI), the feeling that a fake hand belongs to oneself can be induced by the simultaneous, congruent touch of the fake visible hand and one's own hidden hand. This condition is also associated with a recalibration of the perceived location of the real hand. A cortical network, including premotor and temporo-parietal areas, has been proposed as the basis of the RHI. However, the causal contribution of these areas to the discrete illusory components remains unclear. We used transcranial direct current stimulation (tDCS) to assess the contribution of the right premotor cortex (rPMc) and the right temporo-parietal junction (rTPJ) to the RHI and explored the role of these areas in modulating the subjective experience of embodiment and the misperception of the hand position. We found that anodal tDCS of both rPMc and rTPJ increased the misjudgement of the real hand location towards the fake hand. Crucially, the difference in proprioceptive displacement evoked by the congruent and incongruent visuo-tactile stroking was minimised when tDCS was applied over the rPMc, while it was amplified when the rTPJ was targeted. The parietal effects of tDCS also extended to the self-report components of the RHI. These findings suggest that the tDCS of rTPJ modulates the RHI depending on the temporal congruency of the visuo-tactile stimulation, while the tDCS of rPMc induces a general recalibration of hand coordinates, regardless of the visuo-tactile congruency. The present results are discussed in the view of a multicomponent model of the RHI. © 2018 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Field Measurements of Inadvertent Ingestion Exposure to Metals.

PubMed

Gorman Ng, Melanie; MacCalman, Laura; Semple, Sean; van Tongeren, Martie

2017-11-10

The determinants of inadvertent occupational ingestion exposure are poorly understood, largely due to a lack of available exposure measurement data. In this study, perioral exposure wipes were used as a surrogate for inadvertent ingestion exposure to measure exposure to eight metals (chromium, nickel, aluminium, cobalt, lead, arsenic, manganese, and tin) among 38 workers at 5 work sites in the UK. This work was done alongside a previously reported observational study of hand/object-to-mouth contact frequency. Systematic wipes of the perioral area, and of both hands were taken with proprietary cellulose wipes pre-moistened with deionized water. Measurements were taken at the beginning, middle and end of the shift. Mixed-effect models of exposure measurements were built with area of skin sampled, time during shift, and job group entered as fixed effects and worker identification as a random effect. Linear regression modelling was used to study the effect of hand/object-to-mouth contact frequency on perioral exposure, adjusting for the measured exposure on the hand and observed respirator use. Hand and perioral exposure measurements were correlated with one another (r = 0.79) but mass per unit area exposure was significantly higher on the perioral area than on the hands for seven of the metals (at P < 0.05). There were no significant differences between measurements taken at the middle or the end of the shift for five of the metals suggesting that dermal loading may remain relatively constant for much of the workday. This applies to both hand and perioral measurements. In linear regression modelling there was no relationship between hand/object-to-mouth contact frequency and perioral exposure, but hand exposure was significantly positively related to perioral exposure and workers who used respirators had significantly higher perioral exposure than those who did not. The results suggest the levels of exposure on the hand and respirator use are important determinants of potential inadvertent ingestion exposure. The results did not demonstrate a relationship between perioral exposure and hand-to-mouth contact frequency. Perioral wipe sampling may be a useful surrogate measure for exposure by the inadvertent ingestion route, but further research is required to confirm the link between perioral levels and actual exposure, measured using biological monitoring. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

The relationship between frontal sinus morphology and skeletal maturation.

PubMed

Buyuk, Suleyman Kutalmıs; Simsek, Huseyin; Karaman, Ahmet

2018-01-03

The aim of this study is to evaluate the relationship between frontal sinus morphology and hand-wrist bone maturation by using postero-anterior (PA) cephalometric radiographs. The study sample consisted of 220 patients divided into eleven groups based on the hand-wrist radiographs. The right and left maximum height, width and area of the frontal sinus parameters were measured in postero-anterior cephalometric radiographs 220 subjects aged 8-18 years. The hand-wrist skeletal maturation stages were evaluated on the hand-wrist radiographs using the method of Fishman. The Kendall tau-b values were analyzed to evaluate the correlation between the hand-wrist skeletal maturation stages and the frontal sinus parameters. The right and left frontal sinus areas and widths were found to be larger in males than in females (p < 0.05). In males, a significant difference was observed in all frontal sinus parameters in different maturation stages (p < 0.001), while a statistically significant correlation was found in females between the left frontal sinus area, right frontal sinus height, right frontal sinus width and different maturation stages (p < 0.05). In conclusion, the relationship between frontal sinus dimensions obtained from PA cephalometric radiographs and hand-wrist maturation stages suggests that frontal sinuses can be used in determining growth and development.

Unique methods for on-orbit structural repair, maintenance, and assembly

NASA Technical Reports Server (NTRS)

Anderson, Ray; Fuson, Phil

1994-01-01

This paper reviews the MDA independent research and development (IRAD) efforts since 1986 in the development of two distinctly different approaches to on-orbit tube repair: (1) one-piece mechanical tube fittings that are forced, under pressure, onto the tube outer surface to effect the repair; and (2) electron beam weldings as demonstrated with the Paton-developed universal hand tool (UHT) space welding system for the repair of fluid lines and tubular components. Other areas of potential on-orbit repair using the UHT include damage to the flat or curved surfaces of habitation modules and truss assemblies. This paper will also address MDA evaluation of the Paton UHT system for on-orbit coating, cleaning, brazing, and cutting of metals. MDA development of an on-orbit compatible nondestructive evaluation (NDE) system for the inspection of tube welds is an important part of this complete space welding capability and will be discussed in a separate paper.

Classification of Urban Aerial Data Based on Pixel Labelling with Deep Convolutional Neural Networks and Logistic Regression

NASA Astrophysics Data System (ADS)

Yao, W.; Poleswki, P.; Krzystek, P.

2016-06-01

The recent success of deep convolutional neural networks (CNN) on a large number of applications can be attributed to large amounts of available training data and increasing computing power. In this paper, a semantic pixel labelling scheme for urban areas using multi-resolution CNN and hand-crafted spatial-spectral features of airborne remotely sensed data is presented. Both CNN and hand-crafted features are applied to image/DSM patches to produce per-pixel class probabilities with a L1-norm regularized logistical regression classifier. The evidence theory infers a degree of belief for pixel labelling from different sources to smooth regions by handling the conflicts present in the both classifiers while reducing the uncertainty. The aerial data used in this study were provided by ISPRS as benchmark datasets for 2D semantic labelling tasks in urban areas, which consists of two data sources from LiDAR and color infrared camera. The test sites are parts of a city in Germany which is assumed to consist of typical object classes including impervious surfaces, trees, buildings, low vegetation, vehicles and clutter. The evaluation is based on the computation of pixel-based confusion matrices by random sampling. The performance of the strategy with respect to scene characteristics and method combination strategies is analyzed and discussed. The competitive classification accuracy could be not only explained by the nature of input data sources: e.g. the above-ground height of nDSM highlight the vertical dimension of houses, trees even cars and the nearinfrared spectrum indicates vegetation, but also attributed to decision-level fusion of CNN's texture-based approach with multichannel spatial-spectral hand-crafted features based on the evidence combination theory.

Investigation of methods for estimating hand bone dimensions using X-ray hand anthropometric data.

PubMed

Kong, Yong-Ku; Freivalds, Andris; Kim, Dae-Min; Chang, Joonho

2017-06-01

This study examined two conversion methods, M1 and M2, to predict finger/phalange bone lengths based on finger/phalange surface lengths. Forty-one Korean college students (25 males and 16 females) were recruited and their finger/phalange surface lengths, bone lengths and grip strengths were measured using a vernier caliper, an X-ray generator and a double-handle force measurement system, respectively. M1 and M2 were defined as formulas able to estimate finger/phalange bone lengths based on one dimension (i.e., surface hand length) and four finger dimensions (surface finger lengths), respectively. As a result of conversion, the estimation errors by M1 presented mean 1.22 mm, which was smaller than those (1.29 mm) by M2. The bone lengths estimated by M1 (mean r = 0.81) presented higher correlations with the measured bone lengths than those estimated by M2 (0.79). Thus, the M1 method was recommended in the present study, based on conversion simplicity and accuracy.

An introductory study of common grasps used by adults during performance of activities of daily living.

PubMed

Vergara, Margarita; Sancho-Bru, J L; Gracia-Ibáñez, V; Pérez-González, A

2014-01-01

This paper presents the results of a descriptive survey on human grasps. Sixty-four videos were selected to represent tasks performed in the main areas of activities of daily living (ADL) (personal care, meal preparation, eating, housekeeping, etc.). All the participants were right-handed. Elementary grasps were identified for each hand, and the grasp type (from a 9-type classification), the hands involved, and the duration were registered for each case. The results show that the most commonly used grasps are: pinch, non-prehensile, cylindrical, lateral pinch and lumbrical. The presence of these grasps in the areas of ADL is, however, very different (e.g., pinch is widely used in food preparation and very little in driving). Some grasps were used more frequently with one hand or when both hands were used simultaneously (e.g., special pinch was hardly used by the left hand). Knowing the grasp types most frequently used in ADL is essential to be able to assess grasp rehabilitation processes or hand prostheses development. Copyright © 2014 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

Hand hygiene technique quality evaluation in nursing and medicine students of two academic courses 1

PubMed Central

Škodová, Manuela; Gimeno-Benítez, Alfredo; Martínez-Redondo, Elena; Morán-Cortés, Juan Francisco; Jiménez-Romano, Ramona; Gimeno-Ortiz, Alfredo

2015-01-01

Abstract Objective: because they are health professionals, nursing and medical students' hands during internships can function as a transmission vehicle for hospital-acquired infections. Method: a descriptive study with nursing and medical degree students on the quality of the hand hygiene technique, which was assessed via a visual test using a hydroalcoholic solution marked with fluorescence and an ultraviolet lamp. Results: 546 students were assessed, 73.8% from medicine and 26.2% from nursing. The area of the hand with a proper antiseptic distribution was the palm (92.9%); areas not properly scrubbed were the thumbs (55.1%). 24.7% was very good in both hands, 29.8% was good, 25.1% was fair, and 20.3% was poor. The worst assessed were the male, nursing and first year students. There were no significant differences in the age groups. Conclusions: hand hygiene technique is not applied efficiently. Education plays a key role in setting a good practice base in hand hygiene, theoretical knowledge, and in skill development, as well as good practice reinforcement. PMID:26444174

A Combined fMRI and DTI Examination of Functional Language Lateralization and Arcuate Fasciculus Structure: Effects of Degree versus Direction of Hand Preference

ERIC Educational Resources Information Center

Propper, Ruthe E.; O'Donnell, Lauren J.; Whalen, Stephen; Tie, Yanmei; Norton, Isaiah H.; Suarez, Ralph O.; Zollei, Lilla; Radmanesh, Alireza; Golby, Alexandra J.

2010-01-01

The present study examined the relationship between hand preference degree and direction, functional language lateralization in Broca's and Wernicke's areas, and structural measures of the arcuate fasciculus. Results revealed an effect of degree of hand preference on arcuate fasciculus structure, such that consistently-handed individuals,…

"Sharks in Your Hands"--A Case Study on Effects of Teaching Strategies to Change Knowledge and Attitudes towards Sharks

ERIC Educational Resources Information Center

Lee, Hung-Shan; Liu, Shiang-Yao; Yeh, Ting-Kuang

2016-01-01

This study was designed to exemplify how hands-on based teaching strategies enhanced students' knowledge and positive attitudes towards sharks. Hands-on activities for sharks' biological and morphological features were carried out. Eleven elementary school students from a remote area in Taiwan were recruited and assigned to the hands-on condition.…

The influence of respiratory acid-base changes on muscle performance and excitability of the sarcolemma during strenuous intermittent hand grip exercise.

PubMed

Hilbert, M; Shushakov, V; Maassen, N

2012-02-01

Acidification has been reported to provide protective effects on force production in vitro. Thus, in this study, we tested if respiratory acid-base changes influence muscle function and excitability in vivo. Nine subjects performed strenuous, intermittent hand grip exercises (10 cycles of 15 s of work/45 s of rest) under respiratory acidosis by CO(2) rebreathing, alkalosis by hyperventilation, or control. The Pco(2), pH, K(+) concentration ([K(+)]), and Na(+) concentration were measured in venous and arterialized blood. Compound action potentials (M-wave) were elicited to examine the excitability of the sarcolemma. The surface electromyogram (EMG) was recorded to estimate the central drive to the muscle. The lowest venous pH during the exercise period was 7.24 ± 0.03 in controls, 7.31 ± 0.05 with alkalosis, and 7.17 ± 0.04 with acidosis (P < 0.001). The venous [K(+)] rose to similar maximum values in all conditions (6.2 ± 0.8 mmol/l). The acidification reduced the decline in contraction speed (P < 0.001) but decreased the M-wave area to 73.4 ± 19.8% (P < 0.001) of the initial value. After the first exercise cycle, the M-wave area was smaller with acidosis than with alkalosis, and, after the second cycle, it was smaller with acidosis than with the control condition (P < 0.001). The duration of the M-wave was not affected. Acidification diminished the reduction in performance, although the M-wave area during exercise was decreased. Respiratory alkalosis stabilized the M-wave area without influencing performance. Thus, we did not find a direct link between performance and alteration of excitability of the sarcolemma due to changes in pH in vivo.

Does Personalized Water and Hand Quality Information Affect Attitudes, Behavior, and Health in Dar es Salaam, Tanzania?

NASA Astrophysics Data System (ADS)

Davis, J.; Pickering, A.; Horak, H.; Boehm, A.

2008-12-01

Tanzania (TZ) has one of the highest rates of child mortality due to enteric disease in the world. NGOs and local agencies have introduced numerous technologies (e.g., chlorine tablets, borewells) to increase the quantity and quality of water in Dar es Salaam, the capital of Tanzania, in hopes of reducing morbidity and mortality of waterborne disease. The objective of the present study is to determine if providing personalized information about water quality and hand surface quality, as determined by concentrations of enterococci and E. coli, results in improved health and water quality in households. A cohort study was completed in June-September 2008 in 3 communities ranging from urban to per-urban in Dar es Salaam, Tanzania to achieve our objective. The study consisted of 4 cohorts that were visited 4 times over the 3 month study. One cohort received no information about water and hand quality until the end of the summer, while the other groups received either just information on hand surface quality, just information on water quality, and information on both hand surface and water quality after the first (baseline) household visit. We report concentrations of enterococci and E. coli in water sources (surface waters and bore wells), water stored in households, and environmental waters were children and adults swim and bathe. In addition, we report concentrations of enterococci and E. coli on hands of caregivers and children in households. Preliminary results of surveys on health and perceptions of water quality and illness from the households are provided. Ongoing work will integrate the microbiological and sociological data sets to determine if personalized information interventions resulted in changes in health, water quality in the household, or perceptions of water quality, quantity and relation to human health. Future work will analyze DNA samples from hands and water for human-specific Bacteroides bacteria which are only present in human feces. Our study has the potential to provide empirical evidence to promote large scale monitoring and education campaigns in Africa to improve health and reduce the burden of waterborne disease.

Cross-stacked carbon nanotube film as an additional built-in current collector and adsorption layer for high-performance lithium sulfur batteries.

PubMed

Sun, Li; Kong, Weibang; Li, Mengya; Wu, Hengcai; Jiang, Kaili; Li, Qunqing; Zhang, Yihe; Wang, Jiaping; Fan, Shoushan

2016-02-19

Cross-stacked carbon nanotube (CNT) film is proposed as an additional built-in current collector and adsorption layer in sulfur cathodes for advanced lithium sulfur (Li-S) batteries. On one hand, the CNT film with high conductivity, microstructural rough surface, high flexibility and mechanical durability retains stable and direct electronic contact with the sulfur cathode materials, therefore decreasing internal resistivity and suppressing polarization of the cathode. On the other hand, the highly porous structure and the high surface area of the CNT film provide abundant adsorption points to support and confine sulfur cathode materials, alleviate their aggregation and promote high sulfur utilization. Moreover, the lightweight and compact structure of the CNT film adds no extra weight or volume to the sulfur cathode, benefitting the improvement of energy densities. Based on these characteristics, the sulfur cathode with a 100-layer cross-stacked CNT film presents excellent rate performances with capacities of 986, 922 and 874 mAh g(-1) at cycling rates of 0.2C, 0.5C and 1C for sulfur loading of 60 wt%, corresponding to an improvement of 52%, 109% and 146% compared to that without a CNT film. Promising cycling performances are also demonstrated, offering great potential for scaled-up production of sulfur cathodes for Li-S batteries.

Functional asymmetries in early learning during right, left, and bimanual performance in right-handed subjects.

PubMed

Aznárez-Sanado, Maite; Fernández-Seara, Maria A; Loayza, Francis R; Pastor, Maria A

2013-03-01

To elucidate differences in activity and connectivity during early learning due to the performing hand. Twenty right-handed subjects were recruited. The neural correlates of explicit visuospatial learning executed with the right, the left hand, and bimanually were investigated using functional magnetic resonance imaging. Connectivity analyses were carried out using the psychophysiological interactions model, considering right and left anterior putamen as index regions. A common neural network was found for the three tasks during learning. Main activity increases were located in posterior cingulate cortex, supplementary motor area, parietal cortex, anterior putamen, and cerebellum (IV-V), whereas activity decrements were observed in prefrontal regions. However, the left hand task showed a greater recruitment of left hippocampal areas when compared with the other tasks. In addition, enhanced connectivity between the right anterior putamen and motor cortical and cerebellar regions was found for the left hand when compared with the right hand task. An additional recruitment of brain regions and increased striato-cortical and striato-cerebellar functional connections is needed when early learning is performed with the nondominant hand. In addition, access to brain resources during learning may be directed by the dominant hand in the bimanual task. Copyright © 2012 Wiley Periodicals, Inc.

Apparent Brightness and Topography Images of Vibidia Crater

NASA Image and Video Library

2012-03-09

The left-hand image from NASA Dawn spacecraft shows the apparent brightness of asteroid Vesta surface. The right-hand image is based on this apparent brightness image, with a color-coded height representation of the topography overlain onto it.

Interindividual uniformity and variety of the "Writing center": a functional MRI study.

PubMed

Sugihara, Genichi; Kaminaga, Tatsuro; Sugishita, Morihiro

2006-10-01

Our aim is to investigate the neural substrates for writing using fMRI (twenty right-handed subjects). We assumed that common areas involved in both writing with right and left hands are crucial to the central process of writing. We employed Japanese phonograms (Kana), in which phoneme-grapheme conversion would be extremely simple. Brain activation was examined under three conditions: (1) written naming with the right hand (WR), (2) written naming with the left hand (WL), and (3) naming silently (NA). While the comparison of WR to NA (WR>NA) exhibited activation only in the left frontoparietal area, the WL>NA comparison exhibited broader activation than the WR>NA comparison, i.e., the left frontoparietal area except the motor and sensory areas and the right frontoparietal area. A conjunction analysis in SPM2 revealed common areas of activation across the WR>NA and WL>NA comparisons, which are assumed to be crucial to writing. In the group analysis, three areas were found to be activated: the posterior end of the left superior frontal gyrus, which is superior and posterior to Exner's center; the anterior part of the left superior parietal lobule; and the lower part of the anterior limb of the left supramarginal gyrus. In the single-subject analysis, whereas the first two of the above three areas were found to be crucial for writing in all individuals, an interindividual inconsistency of involvement with writing was observed in three areas: the lower part of the anterior limb of the left supramarginal gyrus (60% involved); the right frontal region (47%); and the right intraparietal sulcus (47%).

Systematic Approach to Identifying Deeply Buried Archeological Deposits

DOT National Transportation Integrated Search

2018-02-01

Traditional methods used to discover archeological sites include pedestrian surface surveys and relatively shallow hand-dug shovel or soil core testing. While these methods are appropriate for locating surface and near-surface sites on ridges, hillto...

Atmospheric Dispersion Modeling of 137Cs generated from Nuclear Spent Fuel under Hypothetic Accidental Condition in the BNPP Area

NASA Astrophysics Data System (ADS)

Lee, Jongkuk; Lee, Kwan-Hee; Yook, Daesik; Kim, Sung Il; Lee, Byung Soo

2016-04-01

This study presents the results of atmosphere dispersion modeling using CALPUFF code that are based on computational simulation to evaluate the environmental characteristics of the Barakah nuclear power plant (BNPP) in west area of UAE. According to meteorological data analysis (2012~2013), the winds from the north(7.68%) and west(9.05%) including NNW(41.63%), NW(28.55%), and WNW(6.31%) winds accounted for more than 90% of the wind directions. East(0.2%) and south(0.6%) direction wind, including ESE(0.31%), SE(0.38%), and SSE(0.38%) were rarely distributed during the simulation period. Seasonal effects were not showed. However, a discrepancy in the tendency between daytime and night-time was observed. Approximately 87% of the wind speed was distributed below 5.4m/s (17%, 47% and 23% between the speeds of 0.5-1.8m/s 1.8-3.3m/s and 3.3-5.4m/s, respectively) during the annual period. Seasonal wind speed distribution results presented very similar pattern of annual distribution. Wind speed distribution of day and night, on the other hand, had a discrepancy with annual modeling results than seasonal distribution in some sections. The results for high wind speed (more than 10.8m/s) showed that this wind blew from the west. This high wind speed is known locally as the 'Shamal', which occurs rarely, lasting one or two days with the strongest winds experienced in association with gust fronts and thunderstorms. Six variations of cesium-137 (137Cs) dispersion test were simulated under hypothetic severe accidental condition. The 137Cs dispersion was strongly influenced by the direction and speed of the main wind. From the test cases, east-south area of the BNPP site was mainly influenced by 137Cs dispersion. A virtual receptor was set and calculated for observation of the 137Cs movement and accumulation. Surface roughness tests were performed for the analysis of topographic conditions. According to the surface condition, there are various surface roughness length. Four types of surface conditions were selected, including city area, hedge area, cut grass, and desert area. Four cases of simulations were performed under the same conditions except for surface the roughness factor. The results indicated that relatively high concentrations were found at the high surface roughness near the origin of the source point. The city area contained approximately four times 137Cs concentration than that of desert area. The atmospheric dispersion of 137Cs was affected by the surface condition in the proximal area. Moreover, movement of the radioactive material had a tendency to be dispersed in a relatively wide range in the desert areas compared to in the higher surface roughness areas. The results of these study offer useful information for developing environmental radiation monitoring systems (ERMSs) and evacuation plan under unexpected emergency condition for the BNPP and can be used to assess the environmental effects of new nuclear power plant. This work was supported by the Nuclear Safety Research Program through the Korea Nuclear Safety Foundation(KORSAFe), granted financial resource from the Nuclear Safety and Security Commission(NSSC), Republic of Korea (No. 1503003).

Hand washing practices in two communities of two states of Eastern India: an intervention study.

PubMed

Ray, Sandip Kumar; Zaman, Forhad Akhtar; Laskar, Nasrin Banu

2010-01-01

Public health importance of hand washing as well as its importance in reduction of communicable diseases such as diarrhea and acute respiratory infections have been highlighted in many studies worldwide. This study was designed to study the hand washing practices followed in two urban slums as well as to assess and compare the status of different components of hand washing at the pre- and post-intervention phases. A community-based cross-sectional intervention study on hand washing practices was carried out at two urban slums situated in two states of Eastern India with similar sociocultural and linguistic background. The study was carried out by using an interview technique as well as observation of hand washing practices. Interpersonal communication for behavioural change was chosen as a method of intervention. The majority (>90%) practiced hand washing after defecation in both the study areas. However, hand washing following all six steps and for stipulated time period was seen to be poor before intervention. Significant improvement was observed in all the aspects of hand washing after intervention in both the areas. The poor practice of hand washing was observed in some situations and needed attention. Use of soap and clean material for drying hands after hand washing was poor initially followed by improvement after intervention. Based on the findings of the study, it could be suggested that Behaviour Change Communication program should be further planned with emphasis on different components of hand washing with a final objective to bring down the incidence of target diseases.

Hydrocarbon lakes on Titan

NASA Astrophysics Data System (ADS)

Mitri, Giuseppe; Showman, Adam P.; Lunine, Jonathan I.; Lorenz, Ralph D.

2007-02-01

The Huygens Probe detected dendritic drainage-like features, methane clouds and a high surface relative humidity (∼50% ) on Titan in the vicinity of its landing site [Tomasko, M.G., and 39 colleagues, 2005. Nature 438, 765-778; Niemann, H.B., and 17 colleagues, 2005. Nature 438, 779-784], suggesting sources of methane that replenish this gas against photo- and charged-particle chemical loss on short (10-100) million year timescales [Atreya, S.K., Adams, E.Y., Niemann, H.B., Demick-Montelara, J.E., Owen, T.C., Fulchignoni, M., Ferri, F., Wilson, E.H., 2006. Planet. Space Sci. In press]. On the other hand, Cassini Orbiter remote sensing shows dry and even desert-like landscapes with dunes [Lorenz, R.D., and 39 colleagues, 2006a. Science 312, 724-727], some areas worked by fluvial erosion, but no large-scale bodies of liquid [Elachi, C., and 34 colleagues, 2005. Science 308, 970-974]. Either the atmospheric methane relative humidity is declining in a steady fashion over time, or the sources that maintain the relative humidity are geographically restricted, small, or hidden within the crust itself. In this paper we explore the hypothesis that the present-day methane relative humidity is maintained entirely by lakes that cover a small part of the surface area of Titan. We calculate the required minimum surface area coverage of such lakes, assess the stabilizing influence of ethane, and the implications for moist convection in the atmosphere. We show that, under Titan's surface conditions, methane evaporates rapidly enough that shorelines of any existing lakes could potentially migrate by several hundred m to tens of km per year, rates that could be detected by the Cassini orbiter. We furthermore show that the high relative humidity of methane in Titan's lower atmosphere could be maintained by evaporation from lakes covering only 0.002-0.02 of the whole surface.

Exploration of Force Myography and surface Electromyography in hand gesture classification.

PubMed

Jiang, Xianta; Merhi, Lukas-Karim; Xiao, Zhen Gang; Menon, Carlo

2017-03-01

Whereas pressure sensors increasingly have received attention as a non-invasive interface for hand gesture recognition, their performance has not been comprehensively evaluated. This work examined the performance of hand gesture classification using Force Myography (FMG) and surface Electromyography (sEMG) technologies by performing 3 sets of 48 hand gestures using a prototyped FMG band and an array of commercial sEMG sensors worn both on the wrist and forearm simultaneously. The results show that the FMG band achieved classification accuracies as good as the high quality, commercially available, sEMG system on both wrist and forearm positions; specifically, by only using 8 Force Sensitive Resisters (FSRs), the FMG band achieved accuracies of 91.2% and 83.5% in classifying the 48 hand gestures in cross-validation and cross-trial evaluations, which were higher than those of sEMG (84.6% and 79.1%). By using all 16 FSRs on the band, our device achieved high accuracies of 96.7% and 89.4% in cross-validation and cross-trial evaluations. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Total solar irradiance reconstruction since 1700 using a flux transport model

NASA Astrophysics Data System (ADS)

Dasi Espuig, Maria; Krivova, Natalie; Solanki, Sami K.; Jiang, Jie

Reconstructions of solar irradiance into the past are crucial for studies of solar influence on climate. Models based on the assumption that irradiance changes are caused by the evolution of the photospheric magnetic fields have been most successful in reproducing the measured irradiance variations. Daily magnetograms, such as those from MDI and HMI, provide the most detailed information on the changing distribution of the photospheric magnetic fields. Since such magnetograms are only available from 1974, we used a surface flux transport model to describe the evolution of the magnetic fields on the solar surface due to the effects of differential rotation, meridional circulation, and turbulent diffusivity, before 1974. In this model, the sources of magnetic flux are the active regions, which are introduced based on sunspot group areas, positions, and tilt angles. The RGO record is, however, only available since 1874. Here we present a model of solar irradiance since 1700, which is based on a semi-synthetic sunspot record. The semi-synthetic record was obtained using statistical relationships between sunspot group properties (areas, positions, tilt angles) derived from the RGO record on one hand, and the cycle strength and phase derived from the sunspot group number (Rg) on the other. These relationships were employed to produce daily records of sunspot group positions, areas, and tilt angles before 1874. The semi-synthetic records were fed into the surface flux transport model to simulate daily magnetograms since 1700. By combining the simulated magnetograms with a SATIRE-type model, we then reconstructed total solar irradiance since 1700.

Improving Powder Tableting Performance through Materials Engineering

NASA Astrophysics Data System (ADS)

Osei-Yeboah, Frederick

Adequate mechanical strength is a critical requirement to the successful development of a tablet product. Before tablet compression, powders are often engineered by various processes including wet granulation and surface coating, which may improve or adversely affect the powder tableting performance. Such effects, commonly, result from a change in either particle mechanical properties or particulate (size, shape) properties. In this work, tableting performance is interpreted based on the qualitative bonding-area and bonding-strength (BABS) model. The tabletability of the microcrystalline cellulose (MCC) granules deteriorates rapidly with increasing amount of granulating water and eventually leads to over-granulation at high water level. Granule surface smoothing, size enlargement, granule densification and shape rounding are the dominant factors leading to the tabletability reduction of plastic MCC. Incorporation of increasing amounts of brittle excipients, such as lactose or dibasic calcium phosphate reduces the rate of tabletability reduction by promoting more granule fragmentation, introducing more surface area available for bonding. When a sufficient amount of brittle excipients is used, the over-granulation phenomenon can be eliminated. Surface coating of incompressible MCC pellets with highly bonding polymer leads to sufficient surface deformation and adhesion to enable direct compression of the pellets into tablets of adequate mechanical strength. This improvement is enhanced by the presence of moisture, which plasticizes the polymer to allow the development of a larger bonding area between coated pellets. The relationship between mechanical properties and tableting behavior is systematically investigated in polymeric composites using celecoxib-polyvinylpyrrolidone vinyl acetate solid dispersions. Mechanical properties such as indentation hardness of the solid dispersions were measured using nanoindentation. Incorporation of celecoxib up to 60% by weight hardens the polymers, which reduces bonding area but increases bonding strength. On the other hand, moisture softens the solid dispersions and facilitates deformation under pressure to improve tablet mechanical strength. In summary, insights into the deteriorated tabletability of wet granulated powders have been developed and strategies for improving tabletability have been demonstrated. Also, the relationship between particle mechanical properties and tableting performance has been examined using solid dispersions. The BABS model has been further developed to enable its widespread application in interpreting complex tableting behavior.

Evaluation of surface preparation and maintenance of canal curvature following instrumentation with hand 'K' file and three different Ni-Ti rotary systems: A radiographic and SEM study.

PubMed

Bhatti, Namrata; Sroa, Renu; Sikri, Vimal K

2010-04-01

To determine the shaping ability and cleaning efficiency of hand K-flexofiles, ProTaper, LightSpeed and Mtwo instruments during the preparation of curved root canals in extracted human teeth. A total of 120 root canals of mandibular and maxillary molars with curvature more than 20° were divided into four groups of 30 each. In group A, canals were prepared using hand K-flexofiles following the crown down technique. In group B LightSpeed, in group C ProTaper, and in group D Mtwo rotary instruments were used to prepare the root canals. Using pre- and post-instrumentation radiographs, straightening of the canal curvature was determined with Corel Draw 9.0 software tools. The amount of debris and smear layer were quantified at three different areas (coronal, middle, and apical thirds) of root canal using SEM. The collected data were analyzed statistically using Student's paired 't' test. The mean change in curvature for hand K-files was 7.71°, for ProTaper files 6.03°, for Mtwo 5.43°, and for LightSpeed instruments were found to be 4.57°. The percentage change in the curvature for all the four groups was statistically highly significant (P< 0.01). LightSpeed instruments maintained the original canal curvature significantly (P< 0.01) better than the other instruments. For leftover debris, the minimum percentage was found to be associated with ProTaper (65.48%) followed by Mtwo (66.22%), LightSpeed (71.67%) and the maximum with hand K-files (74.16%). However, the difference in mean leftover debris between ProTaper and Mtwo was not significant. ProTaper and Mtwo resulted in good cleaning, and LightSpeed maintained the original canal curvature better than the ProTaper, Mtwo, or Hand K-files.

The influence of light hypothenar contact during a reaching movement on the centre of pressure (COP) forward displacement.

PubMed

Rugelj, Darja; Trontelj, Jože V; Strojnik, Vojko

2013-01-01

The purpose of this study was to evaluate the effect of additional light hand contact (F<1 N) in the region of the hypothenar eminence on forward movement of the center of pressure (COP) and dominant hand. Subjects sled their hypothenar eminence on a vertically-oriented pressure sensitive board while reaching forward beyond their arm length. In the two separate experiments forty nine healthy, college-aged volunteers participated in the study. Thirty subjects (mean age of 22.2±2.4 years, 6 male and 24 female) participated in the experiment on level ground and nineteen subjects (22±2.6 years, 5 male and 14 female) in the experiment on an elevated surface. The forward displacement of the COP was significantly larger (p = 0.002) when subjects were allowed to slide with the hand as compared to no contact when the activity occurred on level ground (84±10 mm and 79±11 mm, respectively), and on a one meter elevated surface (71±17 mm and 65±21 mm, respectively). The maximal forward reach of the dominant hand was significantly greater when subjects were allowed to slide with the hypothenar eminence as compared to the no contact condition on the level ground (336±35 mm and 344±38 mm, respectively, p<0.02), and on the one meter elevated surface (298±58 mm and 307±58 mm, respectively, p<0.01). This data indicate that subjects were able to use additional haptic information from the hypothenar region to bring their COP and dominant hand further forward while standing on level ground as well as on a one m elevated surface.

VIEW OF ENCLOSED CARPORT AREA. ON RIGHT HAND SIDE IS ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

VIEW OF ENCLOSED CARPORT AREA. ON RIGHT HAND SIDE IS THE ORIGINAL UTILITY ROOM ENTRY DOOR WITH JALOUSIES. VIEW FACING EAST - Camp H.M. Smith and Navy Public Works Center Manana Title VII (Capehart) Housing, Four-Bedroom, Single-Family Type 10, Birch Circle, Elm Drive, Elm Circle, and Date Drive, Pearl City, Honolulu County, HI

The Water music of Vanuatu

NASA Astrophysics Data System (ADS)

Truscott, Tadd; Hurd, Randy; Belden, Jesse; Speirs, Nathan; Merritt, Andrew; Allen, John

2017-11-01

Female musicians from the northern islands of Vanuatu (within larger Polynesia) use the water surface as an instrument to create a variety of unique sounds. Water music is often made by a line of performers standing side by side, waist deep in clear island waters. Accompanied by singing, the women work in unison exhibiting several percussive techniques, which include striking the water surface and throwing handfuls of water which scatter into droplets before impacting the surface. Each interaction produces a unique acoustic response corresponding to the air-water-hand interaction. We highlight the connection between water interaction, cavity shape and the resulting sound which was discovered by these people through their own experimentation.

EEG activation differences in the pre-motor cortex and supplementary motor area between normal individuals with high and low traits of autism.

PubMed

Puzzo, Ignazio; Cooper, Nicholas R; Vetter, Petra; Russo, Riccardo

2010-06-25

The human mirror neuron system (hMNS) is believed to provide a basic mechanism for social cognition. Event-related desynchronization (ERD) in alpha (8-12Hz) and low beta band (12-20Hz) over sensori-motor cortex has been suggested to index mirror neurons' activity. We tested whether autistic traits revealed by high and low scores on the Autistic Quotient (AQ) in the normal population are linked to variations in the electroencephalogram (EEG) over motor, pre-motor cortex and supplementary motor area (SMA) during action observation. Results revealed that in the low AQ group, the pre-motor cortex and SMA were more active during hand action than static hand observation whereas in the high AQ group the same areas were active both during static and hand action observation. In fact participants with high traits of autism showed greater low beta ERD while observing the static hand than those with low traits and this low beta ERD was not significantly different when they watched hand actions. Over primary motor cortex, the classical alpha and low beta ERD during hand actions relative to static hand observation was found across all participants. These findings suggest that the observation-execution matching system works differently according to the degree of autism traits in the normal population and that this is differentiated in terms of the EEG according to scalp site and bandwidth. Copyright 2010 Elsevier B.V. All rights reserved.

Positioning of the sensor cell on the sensing area using cell trapping pattern in incubation type planar patch clamp biosensor.

PubMed

Wang, Zhi-Hong; Takada, Noriko; Uno, Hidetaka; Ishizuka, Toru; Yawo, Hiromu; Urisu, Tsuneo

2012-08-01

Positioning the sensor cell on the micropore of the sensor chip and keeping it there during incubation are problematic tasks for incubation type planar patch clamp biosensors. To solve these problems, we formed on the Si sensor chip's surface a cell trapping pattern consisting of a lattice pattern with a round area 5 μm deep and with the micropore at the center of the round area. The surface of the sensor chip was coated with extra cellular matrix collagen IV, and HEK293 cells on which a chimera molecule of channel-rhodopsin-wide-receiver (ChR-WR) was expressed, were then seeded. We examined the effects of this cell trapping pattern on the biosensor's operation. In the case of a flat sensor chip without a cell trapping pattern, it took several days before the sensor cell covered the micropore and formed an almost confluent state. As a result, multi-cell layers easily formed and made channel current measurements impossible. On the other hand, the sensor chip with cell trapping pattern easily trapped cells in the round area, and formed the colony consisted of the cell monolayer covering the micropore. A laser (473 nm wavelength) induced channel current was observed from the whole cell arrangement formed using the nystatin perforation technique. The observed channel current characteristics matched measurements made by using a pipette patch clamp. Copyright © 2012 Elsevier B.V. All rights reserved.

An IoT-Enabled Stroke Rehabilitation System Based on Smart Wearable Armband and Machine Learning.

PubMed

Yang, Geng; Deng, Jia; Pang, Gaoyang; Zhang, Hao; Li, Jiayi; Deng, Bin; Pang, Zhibo; Xu, Juan; Jiang, Mingzhe; Liljeberg, Pasi; Xie, Haibo; Yang, Huayong

2018-01-01

Surface electromyography signal plays an important role in hand function recovery training. In this paper, an IoT-enabled stroke rehabilitation system was introduced which was based on a smart wearable armband (SWA), machine learning (ML) algorithms, and a 3-D printed dexterous robot hand. User comfort is one of the key issues which should be addressed for wearable devices. The SWA was developed by integrating a low-power and tiny-sized IoT sensing device with textile electrodes, which can measure, pre-process, and wirelessly transmit bio-potential signals. By evenly distributing surface electrodes over user's forearm, drawbacks of classification accuracy poor performance can be mitigated. A new method was put forward to find the optimal feature set. ML algorithms were leveraged to analyze and discriminate features of different hand movements, and their performances were appraised by classification complexity estimating algorithms and principal components analysis. According to the verification results, all nine gestures can be successfully identified with an average accuracy up to 96.20%. In addition, a 3-D printed five-finger robot hand was implemented for hand rehabilitation training purpose. Correspondingly, user's hand movement intentions were extracted and converted into a series of commands which were used to drive motors assembled inside the dexterous robot hand. As a result, the dexterous robot hand can mimic the user's gesture in a real-time manner, which shows the proposed system can be used as a training tool to facilitate rehabilitation process for the patients after stroke.

Bacterial Hand Contamination and Transfer after Use of Contaminated Bulk-Soap-Refillable Dispensers▿†

PubMed Central

Zapka, Carrie A.; Campbell, Esther J.; Maxwell, Sheri L.; Gerba, Charles P.; Dolan, Michael J.; Arbogast, James W.; Macinga, David R.

2011-01-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log10 CFU/ml of Serratia marcescens, an average of 5.28 log10 CFU remained on each hand after washing, and 2.23 log10 CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log10 CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log10 CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log10 CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log10 CFU; P < 0.01). Finally, significantly higher levels of Gram-negative bacteria were recovered from students (2.82 log10 CFU per hand) than were recovered from staff (2.22 log10 CFU per hand) after washing with contaminated bulk soap (P < 0.01). These results demonstrate that washing with contaminated soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings. PMID:21421792

On the Gender Effects of Handedness in Professional Tennis

PubMed Central

Breznik, Kristijan

2013-01-01

The aim of this study was to explore the effects of the gender variable in relation to other player and match characteristics on the advantage possessed by left-handed professional tennis players over their right-handed rivals. The data include 16 732 male tennis players and 16 432 female tennis players who played 438 937 and 415 346 matches, respectively, in the period from 1968 to the end of 2011. The results revealed that the advantage of left-handed professional tennis players is higher in males compared to females. The inverse impact of player and match quality on the left- handers’ advantage was clearly confirmed. On the contrary, it seems that the type of court surface does not directly imply this advantage. To obtain an overview on the individual level, directed and weighted networks of tennis matches in both gender categories were constructed. Applying network analytic methods and the PageRank algorithm, the best left and right-handed players in the Open Era of tennis were identified. The top three ranked left-handed players in the male and female categories were found to be far more consistent in their ranks achieved against left and right-handed opponents compared to their right-handed counterparts. Key Points The advantage of left-handed professional tennis players over their right-handed opponents is higher in males compared to females. The quality of player and match is inversely proportional to the advantage of left-handers against their right-handed counterparts. On the contrary, it seems that the type of court surface does not directly imply this advantage. When the tennis talent appears in left-handers it is likely to be an outstanding one, particularly in the female category. PMID:24149815

Bacterial hand contamination and transfer after use of contaminated bulk-soap-refillable dispensers.

PubMed

Zapka, Carrie A; Campbell, Esther J; Maxwell, Sheri L; Gerba, Charles P; Dolan, Michael J; Arbogast, James W; Macinga, David R

2011-05-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log(10) CFU/ml of Serratia marcescens, an average of 5.28 log(10) CFU remained on each hand after washing, and 2.23 log(10) CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log(10) CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log(10) CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log(10) CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log(10) CFU; P < 0.01). Finally, significantly higher levels of Gram-negative bacteria were recovered from students (2.82 log(10) CFU per hand) than were recovered from staff (2.22 log(10) CFU per hand) after washing with contaminated bulk soap (P < 0.01). These results demonstrate that washing with contaminated soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings.

The effects of cold immersion and hand protection on grip strength.

PubMed

Vincent, M J; Tipton, M J

1988-08-01

The maximal voluntary grip strength (MVGS) of male volunteers was examined following a series of five intermittent 2 min cold water (5 degrees C) immersions of the unprotected hand or forearm. MVGS changes due to wearing a protective glove were also investigated. The surface electrical activity over the hand flexor muscles was recorded, as was the skin temperature of the hand and forearm. MVGS decreased significantly (p less than 0.01) following hand immersions (16%) and forearm immersion (13%). The majority of these reductions occurred during the first 2-min period of immersion. The effect of wearing a glove after unprotected hand cooling also produced significant (p less than 0.01) MVGS reductions which averaged 14%. These reductions were in addition to those caused by hand cooling. We conclude that both hand and forearm protection are important for the maintenance of hand-grip strength following cold water immersion.

Need for new caries detection methods

NASA Astrophysics Data System (ADS)

Young, Douglas A.; Featherstone, John D. B.

1999-05-01

Dental caries (tooth decay) continues to be a major problems for adults as well as children, even though great advances have been made in preventive methods in the last 20 years. New methods for the management of caries will work best if lesions can be detected at an early stage and chemical rather than physical intervention can take place, thereby preserving the natural tooth structure and helping the saliva to heal, or remineralize, the areas of early decay. Clinical detection of caries in the US relies on visual examination, tactile with hand held explorer, and conventional radiographs, all of which are inadequate for the occlusal (biting) surfaces of the teeth where most of the decay now occurs. The dentist often has to explore by drilling with a dental bur to confirm early decay in these areas. New method that can determine the extent and degree of subsurface lesions in these surfaces non-destructively are essential for further advances in the clinical management of dental caries. Optical methods, which exploit the differences between sound and carious enamel and dentin, show great promise for the accurate detection of these lesions. Two or three- dimensional images, which include a measure of severity will be needed.

Self-assembly of short amyloidogenic peptides at the air-water interface.

PubMed

Chaudhary, Nitin; Nagaraj, Ramakrishnan

2011-08-01

Short peptide stretches in amyloidogenic proteins can form amyloid fibrils in vitro and have served as good models for studying amyloid fibril formation. Recently, these amyloidogenic peptides have gained considerable attention, as non-amyloid ordered structures can be obtained from these peptides by carefully tuning the conditions of self-assembly, especially pH, temperature and presence of organic solvents. We have examined the effect of surface pressure on the self-assembled structures of two amyloidogenic peptides, Pβ(2)m (Ac-DWSFYLLYYTEFT-am) and AcPHF6 (Ac-VQIVYK-am) at the air-water interface when deposited from different solvents. Both the peptides are surface-active and form Thioflavin T (ThT) positive structures at the air-water interface. There is considerable hysteresis in the compression and expansion isotherms, suggesting the occurrence of structural rearrangements during compression. Preformed Pβ(2)m fibrillar structures at the air-water interface are disrupted as peptide is compressed to lower molecular areas but restored if the film is expanded, suggesting that the process is reversible. AcPHF6, on the other hand, shows largely sheet-like structures at lower molecular areas. The solvents used for dissolution of the peptides appear to influence the nature of the aggregates formed. Our results show that like hydrostatic pressure, surface pressure can also be utilized for modulating the self-assembly of the amyloidogenic and self-assembling peptides. Copyright © 2011 Elsevier Inc. All rights reserved.

An atraumatic restorative treatment (ART) technique: evaluation after one year.

PubMed

Frencken, J E; Songpaisan, Y; Phantumvanit, P; Pilot, T

1994-10-01

Extraction is the most common dental treatment provided for people in rural and suburban areas in many less-industrialised countries. By comparison, restorative care is rarely provided. In order to improve such situations, a treatment technique has been developed based only on hand excavation of carious lesions and using glass-ionomer cement as a filling material and a sealant. This Atraumatic Restorative Treatment (ART) technique follows the concept of minimal intervention and does not require electrically driven equipment. This paper reports on the longevity of fillings and sealants placed using the technique under field conditions in rural Thailand. Dental caries was treated using the ART technique in one village, whilst the population in a second village received restorative care (amalgam fillings) through mobile dental units. A third village was the control. After one year, 79 per cent of single surface ART fillings and 55 per cent of ART fillings of greater than one surface placed in deciduous teeth were judged successful. The success rate of ART fillings in the permanent dentition (mainly single surface fillings) was 93 per cent and the retention rate for sealants was 78 per cent. Children were pleased at having received treatment by this technique and showed little fear. The ART technique is a promising caries treatment procedure for use in rural and sub-urban areas in less-industrialised countries.

On the Spectral Variance of MGS TES Spectra in the 300-500 cm-1 Range

NASA Astrophysics Data System (ADS)

Altieri, F.; Bellucci, G.

2001-11-01

The Thermal Emission Spectrometer (TES) aboard NASA mission Mars Global Surveyor (MGS) is collecting 200 - 1600 cm-1 thermal emission spectra since September 1997. The principal purpose of TES is to determine and map the Mars surface composition. Spectral features directly ascribable to surface minerals have been identified in the 300 - 500 cm-1 spectral range. Outcrops of hematite have been localized in Sinus Meridiani, Aram Chaos and Valles Marineris [1, 2] and areas with olivine have been individuated in Nili Fossae and in other limited regions [3]. On the other hand, TES spectra show, in general, significant variance between 300 and 500 cm-1; this variance is not directly attributable to surface mineralogical components. In this study we report some examples of spectra with typical hematite and olivine bands and spectra with a different spectral contrast. The spectral masking effect of a dust layer is suggested to explain this behaviour. Spectra characterized by hematite features have been localized also inside a crater near Baldet Crater. The MOC narrow-angle image M02-0039 acquired on the same area shows dark layers at the crater bottom. References: [1] Christensen P. R., et al., JGR, 105, 9623-9642, 2000. [2] Christensen P. R., et al., JGR, in press., 2001. [3] Hoefen T. M. and Clark R. N., LPS XXXII, 2049, 2001.

Quantified outdoor micro-activity data for children aged 7-12-years old.

PubMed

Beamer, Paloma I; Luik, Catherine E; Canales, Robert A; Leckie, James O

2012-01-01

Estimation of aggregate exposure and risk requires detailed information regarding dermal contact and mouthing activity. We analyzed micro-level activity time series (MLATS) of children aged 7-12 years to quantify these contact behaviors and evaluate differences by age and gender. In all, 18 children, aged 7-12 years, were videotaped while playing outdoors. Video footage was transcribed via Virtual Timing Device (VTD) software. We calculated the hand and mouth contact frequency, hourly duration and median duration of contact with 16 object categories. Median mouthing frequencies were 12.6 events/h and 2.6 events/h for hands and non-dietary objects, respectively. Median hourly mouthing duration was 0.4 min/h and 0.1 min/h with hands and objects. Median mouthing contact duration was 1 s and 1.5 s with hands and objects, respectively. The median object contact frequency for both the hands combined was 537.3 events/h with an hourly contact duration of 81.8 min/h and a median contact duration of 3 s. There were no significant differences in the mouthing activity between genders or age groups. Female children had longer and more frequent hand contacts with several surface types. Age was negatively correlated with hand contacts of floor and wood surfaces. Contact frequencies in this study are higher than current regulatory recommendations for this age group.

Hand Motion Classification Using a Multi-Channel Surface Electromyography Sensor

PubMed Central

Tang, Xueyan; Liu, Yunhui; Lv, Congyi; Sun, Dong

2012-01-01

The human hand has multiple degrees of freedom (DOF) for achieving high-dexterity motions. Identifying and replicating human hand motions are necessary to perform precise and delicate operations in many applications, such as haptic applications. Surface electromyography (sEMG) sensors are a low-cost method for identifying hand motions, in addition to the conventional methods that use data gloves and vision detection. The identification of multiple hand motions is challenging because the error rate typically increases significantly with the addition of more hand motions. Thus, the current study proposes two new methods for feature extraction to solve the problem above. The first method is the extraction of the energy ratio features in the time-domain, which are robust and invariant to motion forces and speeds for the same gesture. The second method is the extraction of the concordance correlation features that describe the relationship between every two channels of the multi-channel sEMG sensor system. The concordance correlation features of a multi-channel sEMG sensor system were shown to provide a vast amount of useful information for identification. Furthermore, a new cascaded-structure classifier is also proposed, in which 11 types of hand gestures can be identified accurately using the newly defined features. Experimental results show that the success rate for the identification of the 11 gestures is significantly high. PMID:22438703

Hand motion classification using a multi-channel surface electromyography sensor.

PubMed

Tang, Xueyan; Liu, Yunhui; Lv, Congyi; Sun, Dong

2012-01-01

The human hand has multiple degrees of freedom (DOF) for achieving high-dexterity motions. Identifying and replicating human hand motions are necessary to perform precise and delicate operations in many applications, such as haptic applications. Surface electromyography (sEMG) sensors are a low-cost method for identifying hand motions, in addition to the conventional methods that use data gloves and vision detection. The identification of multiple hand motions is challenging because the error rate typically increases significantly with the addition of more hand motions. Thus, the current study proposes two new methods for feature extraction to solve the problem above. The first method is the extraction of the energy ratio features in the time-domain, which are robust and invariant to motion forces and speeds for the same gesture. The second method is the extraction of the concordance correlation features that describe the relationship between every two channels of the multi-channel sEMG sensor system. The concordance correlation features of a multi-channel sEMG sensor system were shown to provide a vast amount of useful information for identification. Furthermore, a new cascaded-structure classifier is also proposed, in which 11 types of hand gestures can be identified accurately using the newly defined features. Experimental results show that the success rate for the identification of the 11 gestures is significantly high.

Soil frost-induced soil moisture precipitation feedback and effects on atmospheric states

NASA Astrophysics Data System (ADS)

Hagemann, Stefan; Blome, Tanja; Ekici, Altug; Beer, Christian

2016-04-01

Permafrost or perennially frozen ground is an important part of the terrestrial cryosphere; roughly one quarter of Earth's land surface is underlain by permafrost. As it is a thermal phenomenon, its characteristics are highly dependent on climatic factors. The impact of the currently observed warming, which is projected to persist during the coming decades due to anthropogenic CO2 input, certainly has effects for the vast permafrost areas of the high northern latitudes. The quantification of these effects, however, is scientifically still an open question. This is partly due to the complexity of the system, where several feedbacks are interacting between land and atmosphere, sometimes counterbalancing each other. Moreover, until recently, many global circulation models (GCMs) and Earth system models (ESMs) lacked the sufficient representation of permafrost physics in their land surface schemes. Within the European Union FP7 project PAGE21, the land surface scheme JSBACH of the Max-Planck-Institute for Meteorology ESM (MPI-ESM) has been equipped with the representation of relevant physical processes for permafrost studies. These processes include the effects of freezing and thawing of soil water for both energy and water cycles, thermal properties depending on soil water and ice contents, and soil moisture movement being influenced by the presence of soil ice. In the present study, it will be analysed how these permafrost relevant processes impact large-scale hydrology and climate over northern hemisphere high latitude land areas. For this analysis, the atmosphere-land part of MPI-ESM, ECHAM6-JSBACH, is driven by prescribed observed SST and sea ice in an AMIP2-type setup with and without the newly implemented permafrost processes. Results show a large improvement in the simulated discharge. On one hand this is related to an improved snowmelt peak of runoff due to frozen soil in spring. On the other hand a subsequent reduction of soil moisture leads to a positive land atmosphere feedback to precipitation over the high latitudes, which reduces the model's wet biases in precipitation and evapotranspiration during the summer. This is noteworthy as soil moisture - atmosphere feedbacks have previously not been in the research focus over the high latitudes. These results point out the importance of high latitude physical processes at the land surface for the regional climate.

Molecular-level chemistry of model single-crystal oxide surfaces with model halogenated compounds

NASA Astrophysics Data System (ADS)

Adib, Kaveh

Synchrotron-based X-ray photoelectron spectroscopy (XPS), temperature-programmed desorption (TPD) and low energy electron diffraction (LEED) have been used to investigate, at a molecular level, the chemistry of different terminations of single crystal iron-oxide surfaces with probe molecules (CCl4 and D2O). Comparisons of the reactivity of these surfaces towards CCl4, indicate that the presence of an uncapped surface Fe cation (strong Lewis acid site) and an adjacent oxygen site capped by that cation can effect the C-Cl bond cleavage in CCl4, resulting in dissociatively adsorbed Cl-adatoms and carbon-containing fragments. If in addition to these sites, an uncapped surface oxygen (Lewis base) site is also available, the carbon-containing moiety can then move that site, coordinate itself with that uncapped oxygen, and stabilize itself. At a later step, the carbon-containing fragment may form a strong covalent bond with the uncapped oxygen and may even abstract that surface oxygen. On the other hand, if an uncapped oxygen is not available to stabilize the carbon-containing fragment, the surface coordination will not occur and upon the subsequent thermal annealing of the surface the Cl-adatoms and the carbon-containing fragments will recombine and desorb as CCl4. Finally, the presence of surface deuteroxyls blocking the strong Lewis acid and base sites of the reactive surface, passivates this surface. Such a deuteroxylated surface will be unreactive towards CCl 4. Such a molecular level understanding of the surface chemistry of metal-oxides will have applications in the areas of selective catalysis, including environmental catalysis, and chemical sensor technology.

Influenza virus contamination of common household surfaces during the 2009 influenza A (H1N1) pandemic in Bangkok, Thailand: implications for contact transmission.

PubMed

Simmerman, James Mark; Suntarattiwong, Piyarat; Levy, Jens; Gibbons, Robert V; Cruz, Christina; Shaman, Jeffrey; Jarman, Richard G; Chotpitayasunondh, Tawee

2010-11-01

Rational infection control guidance requires an improved understanding of influenza transmission. We studied households with an influenza-infected child to measure the prevalence of influenza contamination, the effect of hand washing, and associations with humidity and temperature. We identified children with influenza and randomly assigned their households to hand washing and control arms. Six common household surfaces and the fingertips of the index patient and symptomatic family members were swabbed. Specimens were tested by real-time reverse-transcription polymerase chain reaction (rRT-PCR), and specimens with positive results were placed on cell culture. A handheld psychrometer measured meteorological data. Sixteen (17.8%) of 90 households had influenza A-positive surfaces by rRT-PCR, but no viruses could be cultured. The fingertips of 15 (16.6%) of the index patients had results positive for influenza A, and 1 virus was cultured. Index patients with seasonal influenza infections shed more virus than did patients with pandemic influenza infection. Control households had a higher prevalence of surface contamination (11 [24.4%] of 45) than did hand washing households (5 [11.1%] of 45); prevalence risk difference (PRD), 13.3%; [95% confidence interval {CI}, −2.2% to 28.9%]; P = .09). Households in which the age of the index patient was ≤8 years had a significantly higher prevalence of contamination (PRD ,19.1%; 95% CI, 5.3% -32.9%; P = .02). Within the strata of households with secondary infections, an effect of lower absolute humidity is suggested (P = .07). We documented influenza virus RNA contamination on household surfaces and on the fingertips of ill children. Homes with younger children were more likely than homes of older children to have contaminated surfaces. Lower absolute humidity favors surface contamination in households with multiple infections. Increased hand washing can reduce influenza contamination in the home.

Reducing absenteeism from gastrointestinal and respiratory illness in elementary school students: a randomized, controlled trial of an infection-control intervention.

PubMed

Sandora, Thomas J; Shih, Mei-Chiung; Goldmann, Donald A

2008-06-01

Students often miss school because of gastrointestinal and respiratory illnesses. We assessed the effectiveness of a multifactorial intervention, including alcohol-based hand-sanitizer and surface disinfection, in reducing absenteeism caused by gastrointestinal and respiratory illnesses in elementary school students. We performed a school-based cluster-randomized, controlled trial at a single elementary school. Eligible students in third to fifth grade were enrolled. Intervention classrooms received alcohol-based hand sanitizer to use at school and quaternary ammonium wipes to disinfect classroom surfaces daily for 8 weeks; control classrooms followed usual hand-washing and cleaning practices. Parents completed a preintervention demographic survey. Absences were recorded along with the reason for absence. Swabs of environmental surfaces were evaluated by bacterial culture and polymerase chain reaction for norovirus, respiratory syncytial virus, influenza, and parainfluenza 3. The primary outcomes were rates of absenteeism caused by gastrointestinal or respiratory illness. Days absent were modeled as correlated Poisson variables and compared between groups by using generalized estimating equations. Analyses were adjusted for family size, race, health status, and home sanitizer use. We also compared the presence of viruses and the total bacterial colony counts on several classroom surfaces. A total of 285 students were randomly assigned; baseline demographics were similar in the 2 groups. The adjusted absenteeism rate for gastrointestinal illness was significantly lower in the intervention-group subjects compared with control subjects. The adjusted absenteeism rate for respiratory illness was not significantly different between groups. Norovirus was the only virus detected and was found less frequently on surfaces in intervention classrooms compared with control classrooms (9% vs 29%). A multifactorial intervention including hand sanitizer and surface disinfection reduced absenteeism caused by gastrointestinal illness in elementary school students. Norovirus was found less often on classroom surfaces in the intervention group. Schools should consider adopting these practices to reduce days lost to common illnesses.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taylor, Mark Patrick, E-mail: mark.taylor@mq.edu.au; Mould, Simon Anthony; Kristensen, Louise Jane

Although blood lead values in children are predominantly falling globally, there are locations where lead exposure remains a persistent problem. One such location is Broken Hill, Australia, where the percentage of blood lead values >10 μg/dL in children aged 1–4 years has risen from 12.6% (2010), to 13% (2011) to 21% (2012). The purpose of this study was to determine the extent of metal contamination in places accessible to children. This study examines contemporary exposure risks from arsenic, cadmium, lead, silver and zinc in surface soil and dust, and in pre- and post-play hand wipes at six playgrounds across Brokenmore » Hill over a 5-day period in September 2013. Soil lead (mean 2,450 mg/kg) and zinc (mean 3,710 mg/kg) were the most elevated metals in playgrounds. Surface dust lead concentrations were consistently elevated (mean 27,500 μg/m{sup 2}) with the highest lead in surface dust (59,900 μg/m{sup 2}) and post-play hand wipes (60,900 μg/m{sup 2}) recorded close to existing mining operations. Surface and post-play hand wipe dust values exceeded national guidelines for lead and international benchmarks for arsenic, cadmium and lead. Lead isotopic compositions ({sup 206}Pb/{sup 207}Pb, {sup 208}Pb/{sup 207}Pb) of surface dust wipes from the playgrounds revealed the source of lead contamination to be indistinct from the local Broken Hill ore body. The data suggest frequent, cumulative and ongoing mine-derived dust metal contamination poses a serious risk of harm to children. - Highlights: 1.Playground soils and surface dust in a mining town have high metal concentrations. 2.Elevated levels of As, Cd, Pb and Zn dust are found on playground users′ hands. 3.Pb isotope analysis shows that the source of playground dust is ore body Pb. 4.Surface mine operations must be contained to reduce childhood lead exposure risks. 5.Mine environmental licences need to set trigger values for As, Cd, Pb and Zn dust.« less

Impact behaviour of auxetic Kevlar®/ epoxy composites

NASA Astrophysics Data System (ADS)

Yang, S.; Chalivendra, V. B.; Kim, Y. K.

2017-10-01

Experimental study was performed to investigate fracture and impact properties of novel Auxetic Kevlar® laminated composites. For comparison, standard Kevlar® woven composites with and without polyurethane surface treatment were also considered in this study. For these three composites, short nylon fibers of two different fiber lengths and three different fiber densities were flocked between laminates. Vacuum infusion process along with optimized compaction was employed to fabricate composites. The double cantilever beam configuration was used to investigate the fracture properties. The Auxetic Kevlar® composites showed a significant improvement of 225% in fracture toughness compared to regular woven Kevlar® composites. Furthermore, the initiation toughness was increased by 577% with the application of flocking in Auxetic Kevlar®. During impact testing, the Auxetic Kevlar® reinforced composites showed a significant reduction in damaged area compared to woven counterpart. On the other hand, the reduction in damaged area influenced the reduction in impact energy absorption.

Fluctuations of Lake Eyre, South Australia

NASA Technical Reports Server (NTRS)

2002-01-01

Lake Eyre is a large salt lake situated between two deserts in one of Australia's driest regions. However, this low-lying lake attracts run-off from one of the largest inland drainage systems in the world. The drainage basin is very responsive to rainfall variations, and changes dramatically with Australia's inter-annual weather fluctuations. When Lake Eyre fills,as it did in 1989, it is temporarily Australia's largest lake, and becomes dense with birds, frogs and colorful plant life. The Lake responds to extended dry periods (often associated with El Nino events) by drying completely.

These four images from the Multi-angle Imaging SpectroRadiometer contrast the lake area at the start of the austral summers of 2000 and 2002. The top two panels portray the region as it appeared on December 9, 2000. Heavy rains in the first part of 2000 caused both the north and south sections of the lake to fill partially and the northern part of the lake still contained significant standing water by the time these data were acquired. The bottom panels were captured on November 29, 2002. Rainfall during 2002 was significantly below average ( http://www.bom.gov.au/ ), although showers occurring in the week before the image was acquired helped alleviate this condition slightly.

The left-hand panels portray the area as it appeared to MISR's vertical-viewing (nadir) camera, and are false-color views comprised of data from the near-infrared, green and blue channels. Here, wet and/or moist surfaces appear blue-green, since water selectively absorbs longer wavelengths such as near-infrared. The right-hand panels are multi-angle composites created with red band data from MISR's 60-degree forward, nadir and 60-degree backward-viewing cameras, displayed as red, green and blue, respectively. In these multi-angle composites, color variations serve as a proxy for changes in angular reflectance, and indicate textural properties of the surface related to roughness and/or moisture content.Data from the two dates were processed identically to preserve relative variations in brightness between them. Wet surfaces or areas with standing water appear green due to the effect of sunglint at the nadir camera view angle. Dry, salt encrusted parts of the lake appear bright white or gray. Purple areas have enhanced forward scattering, possibly as a result of surface moistness. Some variations exhibited by the multi-angle composites are not discernible in the nadir multi-spectral images and vice versa, suggesting that the combination of angular and spectral information is a more powerful diagnostic of surface conditions than either technique by itself.

The Multi-angle Imaging SpectroRadiometer observes the daylit Earth continuously and every 9 days views the entire globe between 82 degrees north and 82 degrees south latitude. These data products were generated from a portion of the imagery acquired during Terra orbits 5194 and 15679. The panels cover an area of 146 kilometers x 122 kilometers, and utilize data from blocks 113 to 114 within World Reference System-2 path 100.

MISR was built and is managed by NASA's Jet Propulsion Laboratory,Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

Contamination by Meat Juice When Shopping for Packages of Raw Poultry.

PubMed

Chen, Fur-Chi; Godwin, Sandria; Chambers, Delores; Chambers, Edgar; Cates, Sheryl; Stone, Richard; Donelan, Amy

2018-05-01

Raw poultry products often are contaminated with Salmonella and Campylobacter, and these bacteria can be transmitted through meat juice on the packages. An observational study was conducted to assess consumer exposure to meat juice during shopping and to quantify the transmission of meat juice from poultry packages to hands and other surfaces. Ninety-six participants completed the shopping study; 402 swabs were collected and analyzed for the presence of meat juice by an immunoassay. Overall, meat juice was detected on 61% of poultry package surfaces, 34% of shoppers' hands, 41% of grocery bags, 60% of kitchen surfaces, and 51% of food item surfaces. When meat juice was detected on the purchased poultry packages, the chance of the meat juice being on the shopper's hands, grocery bags, food items, and kitchen surfaces was significantly higher ( P < 0.005) compared with packages on which meat juice was not present. Shoppers who had poultry wrapped separately during checkout had a significantly lower ( P < 0.05) chance of meat juice on the food items. However, using plastic bags and wrapping poultry separately did not significantly reduce the likelihood of meat juice on kitchen surfaces at home due to consumers' practices of repackaging before storage. Results suggested that the transfer of meat juice through direct contact with the poultry packages is a major concern during shopping and should be prevented.

TRANSFER OF PESTICIDES FROM SURFACES TO FOODS FOR THE ESTIMATION OF DIETARY EXPOSURE OF CHILDREN

EPA Science Inventory

Since small children spend much of their time in contact with contaminated surfaces, residues of pesticides found on floors and other surfaces contribute to their aggregate exposures. Any dislodgeable pesticide residues on hands and surfaces may be transferred to foods while bei...

Directional fractal signature methods for trabecular bone texture in hand radiographs: Data from the Osteoarthritis Initiative

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wolski, M., E-mail: marcin.wolski@curtin.edu.au; Podsiadlo, P.; Stachowiak, G. W.

Purpose: To develop directional fractal signature methods for the analysis of trabecular bone (TB) texture in hand radiographs. Problems associated with the small size of hand bones and the orientation of fingers were addressed. Methods: An augmented variance orientation transform (AVOT) and a quadrant rotating grid (QRG) methods were developed. The methods calculate fractal signatures (FSs) in different directions. Unlike other methods they have the search region adjusted according to the size of bone region of interest (ROI) to be analyzed and they produce FSs defined with respect to any chosen reference direction, i.e., they work for arbitrary orientation ofmore » fingers. Five parameters at scales ranging from 2 to 14 pixels (depending on image size and method) were derived from rose plots of Hurst coefficients, i.e., FS in dominating roughness (FS{sub Sta}), vertical (FS{sub V}) and horizontal (FS{sub H}) directions, aspect ratio (StrS), and direction signatures (StdS), respectively. The accuracy in measuring surface roughness and isotropy/anisotropy was evaluated using 3600 isotropic and 800 anisotropic fractal surface images of sizes between 20 × 20 and 64 × 64 pixels. The isotropic surfaces had FDs ranging from 2.1 to 2.9 in steps of 0.1, and the anisotropic surfaces had two dominating directions of 30° and 120°. The methods were used to find differences in hand TB textures between 20 matched pairs of subjects with (cases: approximate Kellgren-Lawrence (KL) grade ≥2) and without (controls: approximate KL grade <2) radiographic hand osteoarthritis (OA). The OA Initiative public database was used and 20 × 20 pixel bone ROIs were selected on 5th distal and middle phalanges. The performance of the AVOT and QRG methods was compared against a variance orientation transform (VOT) method developed earlier [M. Wolski, P. Podsiadlo, and G. W. Stachowiak, “Directional fractal signature analysis of trabecular bone: evaluation of different methods to detect early osteoarthritis in knee radiographs,” Proc. Inst. Mech. Eng., Part H 223, 211–236 (2009)]. Results: The AVOT method correctly quantified the isotropic and anisotropic surfaces for all image sizes and scales. Values of FS{sub Sta} were significantly different (P < 0.05) between the isotropic surfaces. Using the VOT and QRG methods no differences were found at large scales for the isotropic surfaces that are smaller than 64 × 64 and 48 × 48 pixels, respectively, and at some scales for the anisotropic surfaces with size 48 × 48 pixels. Compared to controls, using the AVOT and QRG methods the authors found that OA TB textures were less rough (P < 0.05) in the dominating and horizontal directions (i.e., lower FS{sub Sta} and FS{sub H}), rougher in the vertical direction (i.e., higher FS{sub V}) and less anisotropic (i.e., higher StrS) than controls. No differences were found using the VOT method. Conclusions: The AVOT method is well suited for the analysis of bone texture in hand radiographs and it could be potentially useful for early detection and prediction of hand OA.« less

Instrumentation For Measuring Finish, Defects And Gloss

NASA Astrophysics Data System (ADS)

Whitehouse, David J.

1985-09-01

The measurement of fine surfaces optical finishes and flaws is becoming more important because of a number of factors. One of these is the hunt for better quality of conformance another is the smoother surfaces required in present day applications such as found in the computer and video industries. Defects such as scratches, pits or cracks cannot only impair the cosmetic appearance of the object, they can actually cause premature failure as in fatigue or corrosion. These new measuring criteria have caused some real problems to instrument makers. In the case of defects the problem is that of spatial bandwidth; that is the problem of searching for a small scratch over a wide area. When measuring fine surfaces the problem is usually the signal to noise ratio of the instrument itself. In many instances the search for defects or the measurement of fine surfaces has been left to human judgement - a powerful if unpredictable measuring tool. This is becoming unsatisfactory because standards have sometimes been built into commercial evaluation of quality based upon the eye. This is rather unfortunate; it ties the hands of the instrument maker who for compatibility has to try to simulate the eye or use indirect measurements.

Demonstration of the First 4H-SiC EUV Detector with Large Detection Area

NASA Technical Reports Server (NTRS)

Xin, Xiaobin; Yan, Feng; Koeth, Timothy W.; Hu, Jun; Zhao, Jian H.

2005-01-01

Ultraviolet (UV) and Extreme Ultraviolet (EUV) detectors are very attractive in astronomy, photolithography and biochemical applications. For EUV applications, most of the semiconductor detectors based on PN or PIN structures suffer from the very short penetration depth. Most of the carries are absorbed at the surface and recombined there due to the high surface recombination before reach the depletion region, resulting very low quantum efficiency. On the other hand, for Schottky structures, the active region starts from the surface and carriers generated from the surface can be efficiently collected. 4H-Sic has a bandgap of 3.26eV and is immune to visible light background noise. Also, 4H-Sic detectors usually have very good radiation hardness and very low noise, which is very important for space applications where the signal is very weak. The E W photodiodes presented in this paper are based on Schottky structures. Platinum (Pt) and Nickel (Ni) are selected as the Schottky contact metals, which have the highest electron work functions (5.65eV and 5.15eV, respectively) among all the known metals on 4H-Sic.

Estimating dermal transfer from PCB-contaminated porous surfaces.

PubMed

Slayton, T M; Valberg, P A; Wait, A D

1998-06-01

Health risks posed by dermal contact with PCB-contaminated porous surfaces have not been directly demonstrated and are difficult to estimate indirectly. Surface contamination by organic compounds is commonly assessed by collecting wipe samples with hexane as the solvent. However, for porous surfaces, hexane wipe characterization is of limited direct use when estimating potential human exposure. Particularly for porous surfaces, the relationship between the amount of organic material collected by hexane and the amount actually picked up by, for example, a person's hand touch is unknown. To better mimic PCB pickup by casual hand contact with contaminated concrete surfaces, we used alternate solvents and wipe application methods that more closely mimic casual dermal contact. Our sampling results were compared to PCB pickup using hexane-wetted wipes and the standard rubbing protocol. Dry and oil-wetted samples, applied without rubbing, picked up less than 1% of the PCBs picked up by the standard hexane procedure; with rubbing, they picked up about 2%. Without rubbing, saline-wetted wipes picked up 2.5%; with rubbing, they picked up about 12%. While the nature of dermal contact with a contaminated surface cannot be perfectly reproduced with a wipe sample, our results with alternate wiping solvents and rubbing methods more closely mimic hand contact than the standard hexane wipe protocol. The relative pickup estimates presented in this paper can be used in conjunction with site-specific PCB hexane wipe results to estimate dermal pickup rates at sites with PCB-contaminated concrete.

Current advances in precious metal core-shell catalyst design.

PubMed

Wang, Xiaohong; He, Beibei; Hu, Zhiyu; Zeng, Zhigang; Han, Sheng

2014-08-01

Precious metal nanoparticles are commonly used as the main active components of various catalysts. Given their high cost, limited quantity, and easy loss of catalytic activity under severe conditions, precious metals should be used in catalysts at low volumes and be protected from damaging environments. Accordingly, reducing the amount of precious metals without compromising their catalytic performance is difficult, particularly under challenging conditions. As multifunctional materials, core-shell nanoparticles are highly important owing to their wide range of applications in chemistry, physics, biology, and environmental areas. Compared with their single-component counterparts and other composites, core-shell nanoparticles offer a new active interface and a potential synergistic effect between the core and shell, making these materials highly attractive in catalytic application. On one hand, when a precious metal is used as the shell material, the catalytic activity can be greatly improved because of the increased surface area and the closed interfacial interaction between the core and the shell. On the other hand, when a precious metal is applied as the core material, the catalytic stability can be remarkably improved because of the protection conferred by the shell material. Therefore, a reasonable design of the core-shell catalyst for target applications must be developed. We summarize the latest advances in the fabrications, properties, and applications of core-shell nanoparticles in this paper. The current research trends of these core-shell catalysts are also highlighted.

Orbital selective spin-texture in a topological insulator

DOE Office of Scientific and Technical Information (OSTI.GOV)

Singh, Bahadur, E-mail: bahadursingh24@gmail.com; Prasad, R.

Three-dimensional topological insulators support a metallic non-trivial surface state with unique spin texture, where spin and momentum are locked perpendicular to each other. In this work, we investigate the orbital selective spin-texture associated with the topological surface states in Sb2Te{sub 3}, using the first principles calculations. Sb2Te{sub 3} is a strong topological insulator with a p-p type bulk band inversion at the Γ-point and supports a single topological metallic surface state with upper (lower) Dirac-cone has left (right) handed spin-texture. Here, we show that the topological surface state has an additional locking between the spin and orbitals, leading to anmore » orbital selective spin-texture. The out-of-plane orbitals (p{sub z} orbitals) have an isotropic orbital texture for both the Dirac cones with an associated left and right handed spin-texture for the upper and lower Dirac cones, respectively. In contrast, the in-planar orbital texture (p{sub x} and p{sub y} projections) is tangential for the upper Dirac-cone and is radial for the lower Dirac-cone surface state. The dominant in-planar orbital texture in both the Dirac cones lead to a right handed orbital-selective spin-texture.« less

Multi-fingered robotic hand

NASA Technical Reports Server (NTRS)

Ruoff, Carl F. (Inventor); Salisbury, Kenneth, Jr. (Inventor)

1990-01-01

A robotic hand is presented having a plurality of fingers, each having a plurality of joints pivotally connected one to the other. Actuators are connected at one end to an actuating and control mechanism mounted remotely from the hand and at the other end to the joints of the fingers for manipulating the fingers and passing externally of the robot manipulating arm in between the hand and the actuating and control mechanism. The fingers include pulleys to route the actuators within the fingers. Cable tension sensing structure mounted on a portion of the hand are disclosed, as is covering of the tip of each finger with a resilient and pliable friction enhancing surface.

[Street food: analysis of hygienic and sanitary conditions of food handlers].

PubMed

de Souza, Giovanna Carbonera; dos Santos, Celso Tadeu Barbosa; Andrade, Anderson Assunção; Alves, Luciene

2015-08-01

The consumption of street food is an economical and practical alternative for the population. However, concerns regarding the safety of these foods are increasing. Thus, this study aimed to analyze the hygienic and sanitary conditions of the street food trade in Uberaba in the State of Minas Gerais. For this purpose, 30 street vending sites were evaluated using a structured questionnaire and microbiological analysis of food handlers' hands and food contact recipients and surfaces. The findings showed low adequacy of street food regarding hand hygiene and food contact surfaces. With respect to surfaces, the results for mesophilic aerobic microorganisms revealed that only 23.3% had satisfactory sanitary conditions. The level of contamination of hands by fecal thermotolerant coliforms and/or Coagulase positive Staphylococci was unsatisfactory in approximately 47% of food handlers. The conclusion drawn is that the hygienic and sanitary conditions of food handlers in Uberaba are poor. It is therefore necessary to adopt effective and permanent training programs on food safety for food handlers urgently.

Application of the Electrical (Geophysical) Method for the Identification of the Sealed Bevel in the Coastal Region of Walidia Province of el Jadida - Morocco

NASA Astrophysics Data System (ADS)

Elfjiji, H.; Boukdir, A.; Zitouni, A.

2018-05-01

The Walidia area knows a great development of agricultural, industrial, maritime activities and a very great demographic expansion. This development is accompanied by a growing demand for water. On the other hand, any intense abstraction of fresh water at a coastal aquifer capture field causes a decrease in groundwater flow and a lowering of the piezometric surface. There is therefore a danger of advancing towards the land of the saltwater bevel and salinization of groundwater which is gradually loaded into mineral salts and can reach abnormally high levels. This work deals with the application of geophysics by electrical sounding method to the in-depth study of the freshwater-salt water interface (salted bevel) on the one hand and the study of the lateral and vertical evolution of the geometry of the different aquifers. The principle of the method is, when performing an electrical survey, to research how varies, at a given point on the surface, the resistivity of the subsoil vertically. For this one executes in a same place a succession of measurements, increasing each time the dimensions of the device and thus the depth of investigation which is proportional to them. At this site, we explore a slice of ground increasingly thick and thus highlights the changes in geological constitution along the vertical. The electrical soundings were carried out with the classic Schlumberger device. The interpretation and the exploitation of the data of the electric soundings carried out made it possible to : Follow the evolution of the salted bevel roof, Draw the upstream limit (marine invasion) of salted bevel Hauterivian, on the one hand, and Valanginian and Jurassic on the other hand, Follow the roof structure of Dridrat limestone (Hauterivien) and limestones of Valanginien and Upper Jurassic, Draw the map of the marl roof of Safi (Hauterivian) constituting the impermeable substratum of Dridrat limestones.

Data-driven grasp synthesis using shape matching and task-based pruning.

PubMed

Li, Ying; Fu, Jiaxin L; Pollard, Nancy S

2007-01-01

Human grasps, especially whole-hand grasps, are difficult to animate because of the high number of degrees of freedom of the hand and the need for the hand to conform naturally to the object surface. Captured human motion data provides us with a rich source of examples of natural grasps. However, for each new object, we are faced with the problem of selecting the best grasp from the database and adapting it to that object. This paper presents a data-driven approach to grasp synthesis. We begin with a database of captured human grasps. To identify candidate grasps for a new object, we introduce a novel shape matching algorithm that matches hand shape to object shape by identifying collections of features having similar relative placements and surface normals. This step returns many grasp candidates, which are clustered and pruned by choosing the grasp best suited for the intended task. For pruning undesirable grasps, we develop an anatomically-based grasp quality measure specific to the human hand. Examples of grasp synthesis are shown for a variety of objects not present in the original database. This algorithm should be useful both as an animator tool for posing the hand and for automatic grasp synthesis in virtual environments.

Analysis of hand contact areas and interaction capabilities during manipulation and exploration.

PubMed

Gonzalez, Franck; Gosselin, Florian; Bachta, Wael

2014-01-01

Manual human-computer interfaces for virtual reality are designed to allow an operator interacting with a computer simulation as naturally as possible. Dexterous haptic interfaces are the best suited for this goal. They give intuitive and efficient control on the environment with haptic and tactile feedback. This paper is aimed at helping in the choice of the interaction areas to be taken into account in the design of such interfaces. The literature dealing with hand interactions is first reviewed in order to point out the contact areas involved in exploration and manipulation tasks. Their frequencies of use are then extracted from existing recordings. The results are gathered in an original graphical interaction map allowing for a simple visualization of the way the hand is used, and compared with a map of mechanoreceptors densities. Then an interaction tree, mapping the relative amount of actions made available through the use of a given contact area, is built and correlated with the losses of hand function induced by amputations. A rating of some existing haptic interfaces and guidelines for their design are finally achieved to illustrate a possible use of the developed graphical tools.

New method for determination of efficacy of health care personnel hand wash products.

PubMed Central

Mahl, M C

1989-01-01

A method of studying the effects of health care personnel hand wash products is described. The fingernail regions of the hands of volunteers are inoculated with a mixture of Escherichia coli and Serratia marcescens, and the areas are dried for a standard time. After routine hand washing, each fingernail region is individually scrubbed with an electric toothbrush which moves longitudinally to the handle into collection fluid contained in a petri dish. The test bacteria in the fluid are then enumerated. (Bacillus subtilis spores may be included as tracers to show degree of physical removal of the procedure.) This method has several advantages over the frequently used glove juice technique. Experimental designs with large numbers of volunteers, multiple sampling sites, and many hand wash products may be performed. Ten sampling sites (fingers) are available, versus the two gloved hands for testing products. (Efficiency is almost 100% in the recovery of spore tracers placed on the fingernails.) Many commercial health care personnel hand wash products containing antimicrobial agents substantive to the skin do not rapidly reduce numbers of inoculated bacteria in the fingernail regions to any greater extent than nonantimicrobial hand washes. Products containing isopropanol or ethanol are very effective in decreasing bacteria in areas around and under the fingernails. PMID:2685028

A novel cluster-tube self-adaptive robot hand.

PubMed

Fu, Hong; Yang, Haokun; Song, Weishu; Zhang, Wenzeng

2017-01-01

This paper proposes a novel cluster-tube self-adaptive robot hand (CTSA Hand). The CTSA Hand consists of a base, a motor, a transmission mechanism, multiple elastic tendons, and a group of sliding-tube assemblies. Each sliding-tube assembly is composed of a sliding tube, a guide rod, two springs and a hinge. When the hand grasping an object, the object pushes some sliding tubes to different positions according to the surface shape of the object, the motor pulls the tendons tight to cluster tubes. The CTSA Hand can realize self-adaptive grasping of objects of different sizes and shapes. The CTSA Hand can grasp multiple objects simultaneously because the grasping of the hand acts as many grippers in different directions and heights. The grasping forces of the hand are adjusted by a closed-loop control system with potentiometer. Experimental results show that the CTSA Hand has the features of highly self-adaption and large grasping forces when grasping various objects.

Cortical Reorganization after Hand Immobilization: The beta qEEG Spectral Coherence Evidences

PubMed Central

Fortuna, Marina; Teixeira, Silmar; Machado, Sérgio; Velasques, Bruna; Bittencourt, Juliana; Peressutti, Caroline; Budde, Henning; Cagy, Mauricio; Nardi, Antonio E.; Piedade, Roberto; Ribeiro, Pedro; Arias-Carrión, Oscar

2013-01-01

There is increasing evidence that hand immobilization is associated with various changes in the brain. Indeed, beta band coherence is strongly related to motor act and sensitive stimuli. In this study we investigate the electrophysiological and cortical changes that occur when subjects are submitted to hand immobilization. We hypothesized that beta coherence oscillations act as a mechanism underlying inter- and intra-hemispheric changes. As a methodology for our study fifteen healthy individuals between the ages of 20 and 30 years were subjected to a right index finger task before and after hand immobilization while their brain activity pattern was recorded using quantitative electroencephalography. This analysis revealed that hand immobilization caused changes in frontal, central and parietal areas of the brain. The main findings showed a lower beta-2 band in frontal regions and greater cortical activity in central and parietal areas. In summary, the coherence increased in the frontal, central and parietal cortex, due to hand immobilization and it adjusted the brains functioning, which had been disrupted by the procedure. Moreover, the brain adaptation upon hand immobilization of the subjects involved inter- and intra-hemispheric changes. PMID:24278213

The cortical activation pattern by a rehabilitation robotic hand: a functional NIRS study

PubMed Central

Chang, Pyung-Hun; Lee, Seung-Hee; Gu, Gwang Min; Lee, Seung-Hyun; Jin, Sang-Hyun; Yeo, Sang Seok; Seo, Jeong Pyo; Jang, Sung Ho

2014-01-01

Introduction: Clarification of the relationship between external stimuli and brain response has been an important topic in neuroscience and brain rehabilitation. In the current study, using functional near infrared spectroscopy (fNIRS), we attempted to investigate cortical activation patterns generated during execution of a rehabilitation robotic hand. Methods: Ten normal subjects were recruited for this study. Passive movements of the right fingers were performed using a rehabilitation robotic hand at a frequency of 0.5 Hz. We measured values of oxy-hemoglobin (HbO), deoxy-hemoglobin (HbR) and total-hemoglobin (HbT) in five regions of interest: the primary sensory-motor cortex (SM1), hand somatotopy of the contralateral SM1, supplementary motor area (SMA), premotor cortex (PMC), and prefrontal cortex (PFC). Results: HbO and HbT values indicated significant activation in the left SM1, left SMA, left PMC, and left PFC during execution of the rehabilitation robotic hand (uncorrected, p < 0.01). By contrast, HbR value indicated significant activation only in the hand somatotopic area of the left SM1 (uncorrected, p < 0.01). Conclusions: Our results appear to indicate that execution of the rehabilitation robotic hand could induce cortical activation. PMID:24570660

Photoactivity of N-doped ZnO nanoparticles in oxidative and reductive reactions

NASA Astrophysics Data System (ADS)

Oliveira, Jéssica A.; Nogueira, André E.; Gonçalves, Maria C. P.; Paris, Elaine C.; Ribeiro, Caue; Poirier, Gael Y.; Giraldi, Tania R.

2018-03-01

N-doped ZnO is a prospective material for photocatalytic reactions. However, only oxidative paths are well investigated in the literature. This paper describes a comparative study about ZnO and ZnO:N potential for oxidative and reductive reactions, probed by rhodamine B dye photodegradation and CO2 photoreduction. The materials were prepared by the polymeric precursor method, using urea as a nitrogen source, and different heat treatments were used to observe their effects on surface decontamination, crystallinity, particle sizes and shapes, and photocatalytic performance. ZnO and ZnO:N presented a wurtzite crystalline structure and nanometric-scale particles. Samples submitted to higher temperatures showed lower specific surface areas, but higher crystallinity and lower contents of species adsorbed on their surfaces. On the other hand, the photocatalysts annealed in shorter times presented smaller crystallite sizes and lower crystallinity. These factors influenced the photoactivity in both conditions, i.e., oxidation and reduction reactions, under the ultraviolet and visible light, indicating that structural factors influenced the adequate charge separation and consequent photocatalytic activity since the as-synthesized samples were versatile photocatalysts in both redox reactions.

Buried nonmetallic object detection using bistatic ground penetrating radar with variable antenna elevation angle and height

NASA Astrophysics Data System (ADS)

Zhang, Yu; Orfeo, Dan; Burns, Dylan; Miller, Jonathan; Huston, Dryver; Xia, Tian

2017-04-01

Ground penetrating radar (GPR) has been shown to be an effective device for detecting buried objects that have little or no metal content, such as plastic, ceramic, and concrete pipes. In this paper, buried non-metallic object detection is evaluated for different antenna elevation angles and heights using a bistatic air-launched GPR. Due to the large standoff distance between antennas and the ground surface, the air-launched GPR has larger spreading loss than the hand-held GPR and vehicle-mounted GPR. Moreover, nonmetallic objects may have similar dielectric property to the buried medium, which results in further difficulty for accurate detection using air-launched GPR. To study such effects, both GPR simulations and GPR laboratory experiments are performed with various setups where antennas are placed at different heights and angles. In the experiments, the test surface areas are configured with and without rocks in order to examine surface clutter effect. The experimental results evaluate the feasibility and effectiveness of bistatic air-launched GPR for detecting buried nonmetallic objects, which provide valuable insights for subsurface scanning with unmanned aerial vehicle (UAV) mounted GPR.

Nonlinear electronic transport and enhanced catalytic behavior caused by native oxides on Cu nanowires

NASA Astrophysics Data System (ADS)

Hajimammadov, Rashad; Csendes, Zita; Ojakoski, Juha-Matti; Lorite, Gabriela Simone; Mohl, Melinda; Kordas, Krisztian

2017-09-01

Electrical transport properties of individual nanowires (both in axial and transversal directions) and their random networks suggest rapid oxidation when Cu is exposed to ambient conditions. The oxidation process is elucidated by thorough XRD, XPS and Raman analyzes conducted for a period of 30 days. Based on the obtained experimental data, we may conclude that first, cuprous oxide and copper hydroxide form that finally transform to cupric oxide. In electrical applications, oxidation of copper is not a true problem as long as thin films or bulk metal is concerned. However, as highlighted in our work, this is not the case for nanowires, since the oxidized surface plays quite important role in the contact formation and also in the conduction of percolated nanowire networks. On the other hand, by taking advantage of the mixed surface oxide states present on the nanowires along with their large specific surface area, we tested and found excellent catalytic activity of the oxidized nanowires in phenol oxidation, which suggests further applications of these materials in catalysis.

Analysis of Vegetation Index Variations and the Asian Monsoon Climate

NASA Technical Reports Server (NTRS)

Shen, Sunhung; Leptoukh, Gregory G.; Gerasimov, Irina

2012-01-01

Vegetation growth depends on local climate. Significant anthropogenic land cover and land use change activities over Asia have changed vegetation distribution as well. On the other hand, vegetation is one of the important land surface variables that influence the Asian Monsoon variability through controlling atmospheric energy and water vapor conditions. In this presentation, the mean and variations of vegetation index of last decade at regional scale resolution (5km and higher) from MODIS have been analyzed. Results indicate that the vegetation index has been reduced significantly during last decade over fast urbanization areas in east China, such as Yangtze River Delta, where local surface temperatures were increased significantly in term of urban heat Island. The relationship between vegetation Index and climate (surface temperature, precipitation) over a grassland in northern Asia and over a woody savannas in southeast Asia are studied. In supporting Monsoon Asian Integrated Regional Study (MAIRS) program, the data in this study have been integrated into Giovanni, the online visualization and analysis system at NASA GES DISC. Most images in this presentation are generated from Giovanni system.

Automated Liquid Microjunction Surface Sampling-HPLC-MS/MS Analysis of Drugs and Metabolites in Whole-Body Thin Tissue Sections

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kertesz, Vilmos; Van Berkel, Gary J

A fully automated liquid extraction-based surface sampling system utilizing a commercially available autosampler coupled to high performance liquid chromatography-tandem mass spectrometry (HPLC-MS/MS) detection is reported. Discrete spots selected for droplet-based sampling and automated sample queue generation for both the autosampler and MS were enabled by using in-house developed software. In addition, co-registration of spatially resolved sampling position and HPLC-MS information to generate heatmaps of compounds monitored for subsequent data analysis was also available in the software. The system was evaluated with whole-body thin tissue sections from propranolol dosed rat. The hands-free operation of the system was demonstrated by creating heatmapsmore » of the parent drug and its hydroxypropranolol glucuronide metabolites with 1 mm resolution in the areas of interest. The sample throughput was approximately 5 min/sample defined by the time needed for chromatographic separation. The spatial distributions of both the drug and its metabolites were consistent with previous studies employing other liquid extraction-based surface sampling methodologies.« less

The Potential of Using Landsat 7 Data for the Classification of Sea Ice Surface Conditions During Summer

NASA Technical Reports Server (NTRS)

Markus, Thorsten; Cavalieri, Donald J.; Ivanoff, Alvaro; Koblinsky, Chester J. (Technical Monitor)

2001-01-01

During spring and summer, the Surface of the Arctic sea ice cover undergoes rapid changes that greatly affect the surface albedo and significantly impact the further decay of the sea ice. These changes are primarily the development of a wet snow cover and the development of melt ponds. As melt pond diameters generally do not exceed a couple of meters, the spatial resolutions of sensors like AVHRR and MODIS are too coarse for their identification. Landsat 7, on the other hand, has a spatial resolution of 30 m (15 m for the pan-chromatic band). The different wavelengths (bands) from blue to near-infrared offer the potential to distinguish among different surface conditions. Landsat 7 data for the Baffin Bay region for June 2000 have been analyzed. The analysis shows that different surface conditions, such as wet snow and meltponded areas, have different signatures in the individual Landsat bands. Consistent with in-situ albedo measurements, melt ponds show up as blueish whereas dry and wet ice have a white to gray appearance in the Landsat true-color image. These spectral differences enable the distinction of melt ponds. The melt pond fraction for the scene studied in this paper was 37%.

Technical note: Correlation of respiratory motion between external patient surface and internal anatomical landmarks

PubMed Central

Fayad, Hadi; Pan, Tinsu; Clément, Jean-François; Visvikis, Dimitris

2011-01-01

Purpose Current respiratory motion monitoring devices used for motion synchronization in medical imaging and radiotherapy provide either 1D respiratory signals over a specific region or 3D information based on few external or internal markers. On the other hand, newer technology may offer the potential to monitor the entire patient external surface in real time. The main objective of this study was to assess the motion correlation between such an external patient surface and internal anatomical landmarks motion. Methods Four dimensional Computed Tomography (4D CT) volumes for ten patients were used in this study. Anatomical landmarks were manually selected in the thoracic region across the 4D CT datasets by two experts. The landmarks included normal structures as well as the tumour location. In addition, a distance map representing the entire external patient surface, which corresponds to surfaces acquired by a Time of Flight (ToF) camera or similar devices, was created by segmenting the skin of all 4D CT volumes using a thresholding algorithm. Finally, the correlation between the internal landmarks and external surface motion was evaluated for different regions (placement and size) throughout a patient’s surface. Results Significant variability was observed in the motion of the different parts of the external patient surface. The larger motion magnitude was consistently measured in the central regions of the abdominal and the thoracic areas for the different patient datasets considered. The highest correlation coefficients were observed between the motion of these external surface areas and internal landmarks such as the diaphragm and mediastinum structures as well as the tumour location landmarks (0.8 ± 0.18 and 0.72 ± 0.12 for the abdominal and the thoracic regions respectively). Worse correlation was observed when one considered landmarks not significantly influenced by respiratory motion such as the apex and the sternum. Discussion and conclusions There were large differences in the motion correlation observed considering different regions of interest placed over a patients’ external surface and internal anatomical landmarks. The positioning of current devices used for respiratory motion synchronization may reduce such correlation by averaging the motion over correlated and poorly correlated external regions. The potential of capturing in real-time the motion of the complete external patient surface as well as choosing the area of the surface that correlates best with the internal motion should allow reducing such variability and associated errors in both respiratory motion synchronization and subsequent motion modeling processes. PMID:21815390

The impact of changing climate on surface and ground water quality in southeast of Ireland

NASA Astrophysics Data System (ADS)

Tribak, Kamal

2015-04-01

In the current changing climate globally, Ireland have been experiencing a yearly recurrent extreme heavy rainfall events in the last decade, with damaging visible effects socially, economically and on the environment. Ireland intensive agriculture production is a major treat to the aquatic environment, Nitrogen and phosphorus losses to the water courses are major causes to eutrophication. The European Water Frame Directive (WFD 2000/60/EC) and Nitrates Directive (91/676/EEC) sets a number of measures to better protect and improve water status. Five years of high temporal resolution river water quality data measurement from two contrasting catchment in the southeast of Ireland were correlated with rain fall and nutrients losses to the ground and surface water, additional to the integrated Southeast River District Basin ground and surface water quality to establish spatiotemporal connection to the agriculture activities, the first well-drained soil catchment had high coefficient correlation with rain fall with higher losses to groundwater, on the other hand higher nutrients losses to surface water were higher with less influence from groundwater recharge of N and P transfer, the poorly clay base soil contributed to higher increased losses to surface water during excessive rain fall. Agriculture activities, hydrology, geology and human interaction can interact according to their site specific setting and the effects will fluctuate dependent on the conditions influencing the impact on water quality, there is a requirement to better distinguish those effects together and identify areas and land uses control and nutrients management to improve the water quality, stakeholders co-operation along with effective polices, long term monitoring, nutrients pathways management and better understanding of the environmental factors interaction on national, regional and catchment scale to enable planning policies and enforcement measures to be more focused on areas of high risk than others.

Mechlorethamine Topical

MedlinePlus

... the treated areas. Wash your hands well with soap and water after applying or touching mechlorethamine gel. ... disposable nitrile gloves and wash hands well with soap and water after removing the gloves. If a ...

Self-Assembly of Rod-Coil Block Copolymers on Carbon Nanotubes: A Route toward Diverse Surface Nanostructures.

PubMed

Han, Yang; Cai, Chunhua; Lin, Jiaping; Gong, Shuting; Xu, Wenheng; Hu, Rui

2018-04-14

In this work, it is reported that poly(γ-benzyl-l-glutamate)-block-poly(ethylene glycol) (PBLG-b-PEG) rod-coil block copolymers (BCPs) can disperse carbon nanotubes (CNTs) in solution and form various surface nanostructures on the CNTs via solution self-assembly. In an organic solvent that dissolves the BCPs, the PBLG rod blocks adsorb on CNT surfaces, and the BCPs form conformal coatings. Then, by the introduction of water, a selective solvent for PEG blocks, the BCPs in the coatings further self-assemble into diverse surface nanostructures, such as helices (left-handed or right-handed), gyros, spheres, and rings. The morphology of the surface nanostructure can be tailored by initial organic solvent composition, preparation temperature, feeding ratio of BCPs to CNTs, degree of polymerization of PBLG blocks, and diameter of the CNTs. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

A national survey of program director opinions of core competencies and structure of hand surgery fellowship training.

PubMed

Sears, Erika Davis; Larson, Bradley P; Chung, Kevin C

2012-10-01

We assessed hand surgery program directors' opinions of essential components of hand surgery training and potential changes in the structure of hand surgery programs. We recruited all 74 program directors of Accreditation Council of Graduate Medical Education-accredited hand surgery fellowship programs to participate. We designed a web-based survey to assess program directors' support for changes in the structure of training programs and to assess opinions of components that are essential for graduates to be proficient. Respondents were asked to rate 9 general areas of practice, 97 knowledge topics, and 172 procedures. Each component was considered essential if 50% or more of respondents thought that graduates must be fully knowledgeable of the topic and be able to perform the procedure at the end of training. The response rate was 84% (n = 62). A minority of program directors (n = 15; 24%) supported creation of additional pathways for hand surgery training, and nearly three-quarters (n = 46; 74%) preferred a fellowship model to an integrated residency model. Most program directors (n = 40; 65%) thought that a 1-year fellowship was sufficient to train a competent hand surgeon. Wrist, distal radius/ulna, forearm, and peripheral nerve conditions were rated as essential areas of practice. Of the detailed components, 76 of 97 knowledge topics and 98 of 172 procedures were rated as essential. Only 48% respondents (n = 30) rated microsurgery as it relates to free tissue transfer as essential. However, small and large vessel laceration repairs were rated as essential by 92% (n = 57) and 77% (n = 48) of respondents, respectively. This study found resistance to prolonging the length of fellowship training and introduction of an integrated residency pathway. To train all hand surgeons in essential components of hand surgery, programs must individually evaluate exposure provided and find innovative ways to augment training when necessary. Studies of curriculum content in hand surgery affect the future scope of hand surgery practice and highlight areas in need of reform and enhancement. Copyright © 2012. Published by Elsevier Inc.

Surface roughness of Saturn's rings and ring particles inferred from thermal phase curves

NASA Astrophysics Data System (ADS)

Morishima, Ryuji; Turner, Neal; Spilker, Linda

2017-10-01

We analyze thermal phase curves of all the main rings of Saturn (the A, B, C rings, and the Cassini division) measured by both the far-IR and mid-IR detectors of the Cassini Composite InfraRed Spectrometer (CIRS). All the rings show temperature increases toward zero phase angle, known as an opposition effect or thermal beaming. For the C ring and Cassini division, which have low optical depths, intra-particle shadowing is considered the dominant mechanism causing the effect. On the other hand, the phase curves of the optically thick B and A rings steepen significantly with decreasing absolute solar elevation angle from 21° to 14°, suggesting inter-particle shadowing plays an important role in these rings. We employ an analytic roughness model to estimate the degrees of surface roughness of the rings or ring particles. For optically thin rings, an isolated particle covered by spherical segment craters is employed while for the thick rings we approximate a packed particle layer as a slab covered by craters. The particles in the thin rings are found to have generally rough surfaces, except in the middle C ring. Across the C ring, the optical depth correlates with the degree of surface roughness. This may indicate that surface roughness comes mainly from particle clumping, while individual particles have rather smooth surfaces. For the optically thick rings, the surface roughness of the particle layer is found to be moderate. The modeled phase curves of optically thick rings are shallow if the phase angle change is primarily due to change of observer azimuthal angle. On the other hand, the phase curves are steep if the phase angle change is due to change of observer elevation angle, as inter-particle shadows become visible at higher observer elevation. In addition, the area of shadowed facets increases with decreasing solar elevation angle. These combined effects explain the large seasonal change of the phase curve steepness observed for the thick rings. The degrees of surface roughness inferred from the thermal phase curves are generally less than those from the phase curves in visible light. This is probably explained by different roughness scales seen in thermal and visible light or by dilution of thermal phase curve steepnesses due to particle motion.

Pre-shaping of the Fingertip of Robot Hand Covered with Net Structure Proximity Sensor

NASA Astrophysics Data System (ADS)

Suzuki, Kenji; Suzuki, Yosuke; Hasegawa, Hiroaki; Ming, Aiguo; Ishikawa, Masatoshi; Shimojo, Makoto

To achieve skillful tasks with multi-fingered robot hands, many researchers have been working on sensor-based control of them. Vision sensors and tactile sensors are indispensable for the tasks, however, the correctness of the information from the vision sensors decreases as a robot hand approaches to a grasping object because of occlusion. This research aims to achieve seamless detection for reliable grasp by use of proximity sensors: correcting the positional error of the hand in vision-based approach, and contacting the fingertip in the posture for effective tactile sensing. In this paper, we propose a method for adjusting the posture of the fingertip to the surface of the object. The method applies “Net-Structure Proximity Sensor” on the fingertip, which can detect the postural error in the roll and pitch axes between the fingertip and the object surface. The experimental result shows that the postural error is corrected in the both axes even if the object dynamically rotates.

Flight set 360L007 (STS-33R) field joint protection system, thermal protection system, and systems tunnel components, volume 7

NASA Technical Reports Server (NTRS)

1990-01-01

The performance of the thermal protection system, field joint protection system, and systems tunnel components of flight set 360L007 is presented as evaluated by postflight hardware inspection. The condition of both motors was similar to previous flights. Four aft edge strikes were noted on the ground environment instrumentation thermal protection system. The hits all left a clean substrate, indicating that the damage was caused by nozzle severance debris and/or water impact. No National Space Transportation System debris criteria for missing thermal protection system were violated. Two problem reports were written against the field joint protection system. The first concerned two cracks in the K5NA closeout over the trunnion/vent valve location on the left-hand aft field joint. A similar condition was observed on Flight 5 (360H005). The second problem report referred to a number of small surface cracks between two impact marks on the left-hand forward field joint. Neither area exhibited loose material or any abnormal heat effects, and they have no impact on flight safety.

Development of a Coded Aperture X-Ray Backscatter Imager for Explosive Device Detection

NASA Astrophysics Data System (ADS)

Faust, Anthony A.; Rothschild, Richard E.; Leblanc, Philippe; McFee, John Elton

2009-02-01

Defence R&D Canada has an active research and development program on detection of explosive devices using nuclear methods. One system under development is a coded aperture-based X-ray backscatter imaging detector designed to provide sufficient speed, contrast and spatial resolution to detect antipersonnel landmines and improvised explosive devices. The successful development of a hand-held imaging detector requires, among other things, a light-weight, ruggedized detector with low power requirements, supplying high spatial resolution. The University of California, San Diego-designed HEXIS detector provides a modern, large area, high-temperature CZT imaging surface, robustly packaged in a light-weight housing with sound mechanical properties. Based on the potential for the HEXIS detector to be incorporated as the detection element of a hand-held imaging detector, the authors initiated a collaborative effort to demonstrate the capability of a coded aperture-based X-ray backscatter imaging detector. This paper will discuss the landmine and IED detection problem and review the coded aperture technique. Results from initial proof-of-principle experiments will then be reported.

Hand-held radiometry: A set of notes developed for use at the Workshop of Hand-held radiometry

NASA Technical Reports Server (NTRS)

Jackson, R. D.; Pinter, P. J., Jr.; Reginato, R. J.; Idso, S. B. (Principal Investigator)

1980-01-01

A set of notes was developed to aid the beginner in hand-held radiometry. The electromagnetic spectrum is reviewed, and pertinent terms are defined. View areas of multiband radiometers are developed to show the areas of coincidence of adjacent bands. The amounts of plant cover seen by radiometers having different fields of view are described. Vegetation indices are derived and discussed. Response functions of several radiometers are shown and applied to spectrometer data taken over 12 wheat plots, to provide a comparison of instruments and bands within and among instruments. The calculation of solar time is reviewed and applied to the calculation of the local time of LANDSAT satellite overpasses for any particular location in the Northern Hemisphere. The use and misuse of hand-held infrared thermometers are discussed, and a procedure for photographic determination of plant cover is described. Some suggestions are offered concerning procedures to be followed when collecting hand-held spectral and thermal data. A list of references pertinent to hand-held radiometry is included.

A neuro-collision avoidance strategy for robot manipulators

NASA Technical Reports Server (NTRS)

Onema, Joel P.; Maclaunchlan, Robert A.

1992-01-01

The area of collision avoidance and path planning in robotics has received much attention in the research community. Our study centers on a combination of an artificial neural network paradigm with a motion planning strategy that insures safe motion of the Articulated Two-Link Arm with Scissor Hand System relative to an object. Whenever an obstacle is encountered, the arm attempts to slide along the obstacle surface, thereby avoiding collision by means of the local tangent strategy and its artificial neural network implementation. This combination compensates the inverse kinematics of a robot manipulator. Simulation results indicate that a neuro-collision avoidance strategy can be achieved by means of a learning local tangent method.

Use of ATP Readings to Predict a Successful Hygiene Intervention in the Workplace to Reduce the Spread of Viruses on Fomites.

PubMed

Sifuentes, Laura Y; Fankem, Sonia L M; Reynolds, Kelly; Tamimi, Akrum H; Gerba, Charles P; Koenig, David

2017-03-01

The purpose of this study was to validate the use of adenosine triphosphate (ATP) for evaluating hygiene intervention effectiveness in reducing viral dissemination in an office environment. The bacterial virus MS-2 was used to evaluate two scenarios, one where the hand of an individual was contaminated and another where a fomite was contaminated. MS-2 was selected as a model because its shape and size are similar to many human pathogenic viruses. Two separate experiments were conducted, one in which the entrance door push plate was inoculated and the other in which the hand of one selected employee was inoculated. In both scenarios, 54 selected surfaces in the office were tested to assess the dissemination of the virus within the office. Associated surface contamination was also measured employing an ATP meter. More than half of the tested hands and surfaces in the office were contaminated with MS-2 within 4 h. Next, an intervention was conducted, and each scenario was repeated. Half of the participating employees were provided hand sanitizer, facial tissues, and disinfecting wipes, and were instructed in their use. A significant (p < 0.05) reduction was observed in the number of surfaces contaminated with virus. This reduction in viral spread was evident from the results of both viral culture and the surface ATP measurements, although there was no direct correlation between ATP measurements with respect to viral concentration. Although ATP does not measure viruses, these results demonstrate that ATP measurements could be useful for evaluating the effectiveness of hygiene interventions aimed at preventing viral spread in the workplace.

Brain Decoding-Classification of Hand Written Digits from fMRI Data Employing Bayesian Networks

PubMed Central

Yargholi, Elahe'; Hossein-Zadeh, Gholam-Ali

2016-01-01

We are frequently exposed to hand written digits 0–9 in today's modern life. Success in decoding-classification of hand written digits helps us understand the corresponding brain mechanisms and processes and assists seriously in designing more efficient brain–computer interfaces. However, all digits belong to the same semantic category and similarity in appearance of hand written digits makes this decoding-classification a challenging problem. In present study, for the first time, augmented naïve Bayes classifier is used for classification of functional Magnetic Resonance Imaging (fMRI) measurements to decode the hand written digits which took advantage of brain connectivity information in decoding-classification. fMRI was recorded from three healthy participants, with an age range of 25–30. Results in different brain lobes (frontal, occipital, parietal, and temporal) show that utilizing connectivity information significantly improves decoding-classification and capability of different brain lobes in decoding-classification of hand written digits were compared to each other. In addition, in each lobe the most contributing areas and brain connectivities were determined and connectivities with short distances between their endpoints were recognized to be more efficient. Moreover, data driven method was applied to investigate the similarity of brain areas in responding to stimuli and this revealed both similarly active areas and active mechanisms during this experiment. Interesting finding was that during the experiment of watching hand written digits, there were some active networks (visual, working memory, motor, and language processing), but the most relevant one to the task was language processing network according to the voxel selection. PMID:27468261

A simple topography-driven, calibration-free runoff generation model

NASA Astrophysics Data System (ADS)

Gao, H.; Birkel, C.; Hrachowitz, M.; Tetzlaff, D.; Soulsby, C.; Savenije, H. H. G.

2017-12-01

Determining the amount of runoff generation from rainfall occupies a central place in rainfall-runoff modelling. Moreover, reading landscapes and developing calibration-free runoff generation models that adequately reflect land surface heterogeneities remains the focus of much hydrological research. In this study, we created a new method to estimate runoff generation - HAND-based Storage Capacity curve (HSC) which uses a topographic index (HAND, Height Above the Nearest Drainage) to identify hydrological similarity and partially the saturated areas of catchments. We then coupled the HSC model with the Mass Curve Technique (MCT) method to estimate root zone storage capacity (SuMax), and obtained the calibration-free runoff generation model HSC-MCT. Both the two models (HSC and HSC-MCT) allow us to estimate runoff generation and simultaneously visualize the spatial dynamic of saturated area. We tested the two models in the data-rich Bruntland Burn (BB) experimental catchment in Scotland with an unusual time series of the field-mapped saturation area extent. The models were subsequently tested in 323 MOPEX (Model Parameter Estimation Experiment) catchments in the United States. HBV and TOPMODEL were used as benchmarks. We found that the HSC performed better in reproducing the spatio-temporal pattern of the observed saturated areas in the BB catchment compared with TOPMODEL which is based on the topographic wetness index (TWI). The HSC also outperformed HBV and TOPMODEL in the MOPEX catchments for both calibration and validation. Despite having no calibrated parameters, the HSC-MCT model also performed comparably well with the calibrated HBV and TOPMODEL, highlighting the robustness of the HSC model to both describe the spatial distribution of the root zone storage capacity and the efficiency of the MCT method to estimate the SuMax. Moreover, the HSC-MCT model facilitated effective visualization of the saturated area, which has the potential to be used for broader geoscience studies beyond hydrology.

Space Station Freedom combustion research

NASA Technical Reports Server (NTRS)

Faeth, G. M.

1992-01-01

Extended operations in microgravity, on board spacecraft like Space Station Freedom, provide both unusual opportunities and unusual challenges for combustion science. On the one hand, eliminating the intrusion of buoyancy provides a valuable new perspective for fundamental studies of combustion phenomena. On the other hand, however, the absence of buoyancy creates new hazards of fires and explosions that must be understood to assure safe manned space activities. These considerations - and the relevance of combustion science to problems of pollutants, energy utilization, waste incineration, power and propulsion systems, and fire and explosion hazards, among others - provide strong motivation for microgravity combustion research. The intrusion of buoyancy is a greater impediment to fundamental combustion studies than to most other areas of science. Combustion intrinsically heats gases with the resulting buoyant motion at normal gravity either preventing or vastly complicating measurements. Perversely, this limitation is most evident for fundamental laboratory experiments; few practical combustion phenomena are significantly affected by buoyancy. Thus, we have never observed the most fundamental combustion phenomena - laminar premixed and diffusion flames, heterogeneous flames of particles and surfaces, low-speed turbulent flames, etc. - without substantial buoyant disturbances. This precludes rational merging of theory, where buoyancy is of little interest, and experiments, that always are contaminated by buoyancy, which is the traditional path for developing most areas of science. The current microgravity combustion program seeks to rectify this deficiency using both ground-based and space-based facilities, with experiments involving space-based facilities including: laminar premixed flames, soot processes in laminar jet diffusion flames, structure of laminar and turbulent jet diffusion flames, solid surface combustion, one-dimensional smoldering, ignition and flame spread of liquids, drop combustion, and quenching of panicle-air flames. Unfortunately, the same features that make microgravity attractive for fundamental combustion experiments, introduce new fire and explosion hazards that have no counterpart on earth. For example, microgravity can cause broader flammability limits, novel regimes of flame spread, enhanced effects of flame radiation, slower fire detector response, and enhanced combustion upon injecting fire extinguishing agents, among others. On the other hand, spacecraft provide an opportunity to use 'fire-safe' atmospheres due to their controlled environment. Investigation of these problems is just beginning, with specific fire safety experiments supplementing the space based fundamental experiments listed earlier; thus, much remains to be done to develop an adequate technology base for fire and explosion safety considerations for spacecraft.

Correlations of indoor second-hand smoking, household smoking rules, regional deprivation and children mental health: Scottish Health Survey, 2013.

PubMed

Shiue, Ivy

2015-07-01

It has been known that second-hand smoking and deprivation could cluster together affecting child health. However, little is known on the role of household smoking rules. Therefore, it was aimed to study the relationships among indoor second-hand smoking, household smoking rules, deprivation level and children mental health in a country-wide and population-based setting. Data was retrieved from and analysed in Scottish Health Survey, 2013. Information on demographics, indoor second-hand smoking status, household smoking rules, deprivation level and child mental health by Strengths and Difficulties Questionnaire was obtained by household interview through parents. Statistical analysis included chi-square test and survey-weighted logistic regression modelling. Of 1019 children aged 4-12, 17.9% (n = 182) lived in the 15% most deprivation areas. Deprived areas tended to be where indoor smoking occurred (p < 0.001). The top three sub-regions of the 15% most deprivation for Scottish children are greater Glasgow, Ayrshire & Arran and Forth Valley while the top three sub-regions of exposure to the indoor second-hand smoking are Fife, Forth Valley and Ayrshire & Arran. The top three sub-regions with indoor smoking allowed are greater Glasgow, Western Isles and Borders. Children emotional and behavioural problems were reduced when the strict household smoking rules (not allowed or outdoor areas) applied. One in six Scottish children lived in the 15% most deprivation areas and exposed to indoor second-hand smoking that could have led to emotional and behavioural problems. Public health programs promoting strict household smoking rules should be encouraged in order to optimise children mental health.

Transmission of SARS and MERS coronaviruses and influenza virus in healthcare settings: the possible role of dry surface contamination.

PubMed

Otter, J A; Donskey, C; Yezli, S; Douthwaite, S; Goldenberg, S D; Weber, D J

2016-03-01

Viruses with pandemic potential including H1N1, H5N1, and H5N7 influenza viruses, and severe acute respiratory syndrome (SARS)/Middle East respiratory syndrome (MERS) coronaviruses (CoV) have emerged in recent years. SARS-CoV, MERS-CoV, and influenza virus can survive on surfaces for extended periods, sometimes up to months. Factors influencing the survival of these viruses on surfaces include: strain variation, titre, surface type, suspending medium, mode of deposition, temperature and relative humidity, and the method used to determine the viability of the virus. Environmental sampling has identified contamination in field-settings with SARS-CoV and influenza virus, although the frequent use of molecular detection methods may not necessarily represent the presence of viable virus. The importance of indirect contact transmission (involving contamination of inanimate surfaces) is uncertain compared with other transmission routes, principally direct contact transmission (independent of surface contamination), droplet, and airborne routes. However, influenza virus and SARS-CoV may be shed into the environment and be transferred from environmental surfaces to hands of patients and healthcare providers. Emerging data suggest that MERS-CoV also shares these properties. Once contaminated from the environment, hands can then initiate self-inoculation of mucous membranes of the nose, eyes or mouth. Mathematical and animal models, and intervention studies suggest that contact transmission is the most important route in some scenarios. Infection prevention and control implications include the need for hand hygiene and personal protective equipment to minimize self-contamination and to protect against inoculation of mucosal surfaces and the respiratory tract, and enhanced surface cleaning and disinfection in healthcare settings. Copyright © 2015 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

An efficient solid modeling system based on a hand-held 3D laser scan device

NASA Astrophysics Data System (ADS)

Xiong, Hanwei; Xu, Jun; Xu, Chenxi; Pan, Ming

2014-12-01

The hand-held 3D laser scanner sold in the market is appealing for its port and convenient to use, but price is expensive. To develop such a system based cheap devices using the same principles as the commercial systems is impossible. In this paper, a simple hand-held 3D laser scanner is developed based on a volume reconstruction method using cheap devices. Unlike convenient laser scanner to collect point cloud of an object surface, the proposed method only scan few key profile curves on the surface. Planar section curve network can be generated from these profile curves to construct a volume model of the object. The details of design are presented, and illustrated by the example of a complex shaped object.

An IoT-Enabled Stroke Rehabilitation System Based on Smart Wearable Armband and Machine Learning

PubMed Central

Yang, Geng; Pang, Gaoyang; Zhang, Hao; Li, Jiayi; Deng, Bin; Pang, Zhibo; Xu, Juan; Jiang, Mingzhe; Liljeberg, Pasi; Xie, Haibo; Yang, Huayong

2018-01-01

Surface electromyography signal plays an important role in hand function recovery training. In this paper, an IoT-enabled stroke rehabilitation system was introduced which was based on a smart wearable armband (SWA), machine learning (ML) algorithms, and a 3-D printed dexterous robot hand. User comfort is one of the key issues which should be addressed for wearable devices. The SWA was developed by integrating a low-power and tiny-sized IoT sensing device with textile electrodes, which can measure, pre-process, and wirelessly transmit bio-potential signals. By evenly distributing surface electrodes over user’s forearm, drawbacks of classification accuracy poor performance can be mitigated. A new method was put forward to find the optimal feature set. ML algorithms were leveraged to analyze and discriminate features of different hand movements, and their performances were appraised by classification complexity estimating algorithms and principal components analysis. According to the verification results, all nine gestures can be successfully identified with an average accuracy up to 96.20%. In addition, a 3-D printed five-finger robot hand was implemented for hand rehabilitation training purpose. Correspondingly, user’s hand movement intentions were extracted and converted into a series of commands which were used to drive motors assembled inside the dexterous robot hand. As a result, the dexterous robot hand can mimic the user’s gesture in a real-time manner, which shows the proposed system can be used as a training tool to facilitate rehabilitation process for the patients after stroke. PMID:29805919

Comparisons of Rain Estimates from Ground Radar and Satellite Over Mountainous Regions

NASA Technical Reports Server (NTRS)

Lin, Xin; Kidd, Chris; Tao, Jing; Barros, Ana

2016-01-01

A high-resolution rainfall product merging surface radar and an enhanced gauge network is used as a reference to examine two operational surface radar rainfall products over mountain areas. The two operational rainfall products include radar-only and conventional-gauge-corrected radar rainfall products. Statistics of rain occurrence and rain amount including their geographical, seasonal, and diurnal variations are examined using 3-year data. It is found that the three surface radar rainfall products in general agree well with one another over mountainous regions in terms of horizontal mean distributions of rain occurrence and rain amount. Frequency of rain occurrence and fraction of rain amount also indicate similar distribution patterns as a function of rain intensity. The diurnal signals of precipitation over mountain ridges are well captured and joint distributions of coincident raining samples indicate reasonable correlations during both summer and winter. Factors including undetected low-level precipitation, limited availability of gauges for correcting the Z-R relationship over the mountains, and radar beam blocking by mountains are clearly noticed in the two conventional radar rainfall products. Both radar-only and conventional-gauge-corrected radar rainfall products underestimate the rain occurrence and fraction of rain amount at intermediate and heavy rain intensities. Comparison of PR and TMI against a surface radar-only rainfall product indicates that the PR performs equally well with the high-resolution radar-only rainfall product over complex terrains at intermediate and heavy rain intensities during the summer and winter. TMI, on the other hand, requires improvement to retrieve wintertime precipitation over mountain areas.

Smoothed particle hydrodynamics study of the roughness effect on contact angle and droplet flow

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shigorina, Elena; Kordilla, Jannes; Tartakovsky, Alexandre M.

We employ a pairwise force Smoothed Particle Hydrodynamics (PF-SPH) model to simulate sessile and transient droplets on rough hydrophobic and hydrophilic surfaces. PF-SPH allows for modeling of free surface flow without discretizing the air phase, which is achieved by imposing the surface tension and dynamic contact angles with pairwise interaction forces. We use the PF-SPH model to study the effect of surface roughness and microscopic contact angle on the effective contact angle and droplet dynamics. In the first part of this work, we investigate static contact angles of sessile droplets on rough surfaces in a shape of a sinusoidal functionmore » and made of rectangular bars placed on top of a flat surface. We find that the effective static contact angles of Cassie and Wenzel droplets on a rough surface are greater than the corresponding microscale static contact angles. As a result, microscale hydrophobic rough surfaces also show effective hydrophobic behavior. On the other hand, microscale hydrophilic surfaces may be macroscopically hydrophilic or hydrophobic, depending on the type of roughness. Next, we study the impact of the roughness orientation (i.e., an anisotropic roughness) and surface inclination on droplet flow velocities. Simulations show that droplet flow velocities are lower if the surface roughness is oriented perpendicular to the flow direction. If the predominant elements of surface roughness are in alignment with the flow direction, the flow velocities increase compared to smooth surfaces, which can be attributed to the decrease in fluid-solid contact area similar to the classical lotus effect. We demonstrate that linear scaling relationships between Bond and capillary number for droplet flow on flat surfaces also hold for flow on rough surfaces.« less

Recent increase in snow-melt area in the Greenland Ice sheet as an indicator of the effect of reduced surface albedo by snow impurities

NASA Astrophysics Data System (ADS)

Rikiishi, K.

2008-12-01

Recent rapid decline of cryosphere including mountain glaciers, sea ice, and seasonal snow cover tends to be associated with global warming. However, positive feedback is likely to operate between the cryosphere and air temperature, and then it may not be so simple to decide the cause-and-effect relation between them. The theory of heat budget for snow surface tells us that sensible heat transfer from the air to the snow by atmospheric warming by 1°C is about 10 W/m2, which is comparable with heat supply introduced by reduction of the snow surface albedo by only 0.02. Since snow impurities such as black carbon and soil- origin dusts have been accumulated every year on the snow surface in snow-melting season, it is very important to examine whether the snow-melting on the ice sheets, mountain glaciers, and sea ice is caused by global warming or by accumulated snow impurities originated from atmospheric pollutants. In this paper we analyze the dataset of snow-melt area in the Greenland ice sheet for the years 1979 - 2007 (available from the National Snow and Ice Data Center), which is reduced empirically from the satellite micro-wave observations by SMMR and SMM/I. It has been found that, seasonally, the snow-melt area extends most significantly from the second half of June to the first half of July when the sun is highest and sunshine duration is longest, while it doesn't extend any more from the second half of July to the first half of August when the air temperature is highest. This fact may imply that sensible heat required for snow-melting comes from the solar radiation rather than from the atmosphere. As for the interannual variation of snow-melt area, on the other hand, we have found that the growth rate of snow-melt area gradually increases from July, to August, and to the first half of September as the impurities come out to and accumulated at the snow surface. However, the growth rate is almost zero in June and the second half of September when fresh snow of high albedo covers the surface. This fact may imply that the combined operation of solar radiation and snow impurities is responsible for the recent global decline of cryosphere. Discussion about other research works will be given in the presentation in order to support the above idea.

Correlations between skin blood perfusion values and nailfold capillaroscopy scores in systemic sclerosis patients.

PubMed

Ruaro, B; Sulli, A; Pizzorni, C; Paolino, S; Smith, V; Cutolo, M

2016-05-01

To correlate blood perfusion (BP) values assessed by laser speckle contrast analysis (LASCA) in selected skin areas of hands and face with nailfold capillary damage scores in systemic sclerosis (SSc) patients. Seventy SSc patients (mean SSc duration 6 ± 5 years) and 70 volunteer healthy subjects were enrolled after informed consent. LASCA was performed at different areas of the face (forehead, tip of nose, zygomas and perioral region) and at dorsal and volar regions of hands. Microvascular damage was assessed and scored by nailfold videocapillaroscopy (NVC) and the microangiopathy evolution score (MES) was calculated. SSc patients showed a significantly lower BP than healthy subjects at fingertips, periungual areas and palm of hands (p<0.0001), but not at the level of face and dorsum of hands. A gradual decrease of BP at fingertips, periungual and palm areas, was found in SSc patients with progressive severity of NVC patterns of microangiopathy ("early", "active", or "late") (p<0.01). A negative correlation was observed between MES and BP values, as well as between loss of capillaries and BP, at the same areas (p<0.001 and p<0.01, respectively). Patients with diffuse cutaneous SSc (dcSSc) showed lower BP than those with limited cutaneous SSc (p<0.04). LASCA detects a significant reduction of BP only in those areas usually affected by Raynaud's phenomenon (fingertips, periungual and palm areas), especially in dcSSc patients, and BP values significantly correlate with the nailfold capillaroscopy scores of microangiopathy. Copyright © 2016. Published by Elsevier Inc.

Candida auris: Disinfectants and Implications for Infection Control.

PubMed

Ku, Tsun S N; Walraven, Carla J; Lee, Samuel A

2018-01-01

Candida auris is a rapidly emerging pathogen and is able to cause severe infections with high mortality rates. It is frequently misidentified in most clinical laboratories, thus requiring more specialized identification techniques. Furthermore, several clinical isolates have been found to be multidrug resistant and there is evidence of nosocomial transmission in outbreak fashion. Appropriate infection control measures will play a major role in controlling the management and spread of this pathogen. Unfortunately, there are very few data available on the effectiveness of disinfectants against C. auris . Chlorine-based products appear to be the most effective for environmental surface disinfection. Other disinfectants, although less effective than chlorine-based products, may have a role as adjunctive disinfectants. A cleaning protocol will also need to be established as the use of disinfectants alone may not be sufficient for maximal decontamination of patient care areas. Furthermore, there are fewer data on the effectiveness of antiseptics against C. auris for patient decolonization and hand hygiene for healthcare personnel. Chlorhexidine gluconate has shown some efficacy in in vitro studies but there are reports of patients with persistent colonization despite twice daily body washes with this disinfectant. Hand hygiene using soap and water, with or without chlorhexidine gluconate, may require the subsequent use of alcohol-based hand sanitizer for maximal disinfection. Further studies will be needed to validate the currently studied disinfectants for use in real-world settings.

Candida auris: Disinfectants and Implications for Infection Control

PubMed Central

Ku, Tsun S. N.; Walraven, Carla J.; Lee, Samuel A.

2018-01-01

Candida auris is a rapidly emerging pathogen and is able to cause severe infections with high mortality rates. It is frequently misidentified in most clinical laboratories, thus requiring more specialized identification techniques. Furthermore, several clinical isolates have been found to be multidrug resistant and there is evidence of nosocomial transmission in outbreak fashion. Appropriate infection control measures will play a major role in controlling the management and spread of this pathogen. Unfortunately, there are very few data available on the effectiveness of disinfectants against C. auris. Chlorine-based products appear to be the most effective for environmental surface disinfection. Other disinfectants, although less effective than chlorine-based products, may have a role as adjunctive disinfectants. A cleaning protocol will also need to be established as the use of disinfectants alone may not be sufficient for maximal decontamination of patient care areas. Furthermore, there are fewer data on the effectiveness of antiseptics against C. auris for patient decolonization and hand hygiene for healthcare personnel. Chlorhexidine gluconate has shown some efficacy in in vitro studies but there are reports of patients with persistent colonization despite twice daily body washes with this disinfectant. Hand hygiene using soap and water, with or without chlorhexidine gluconate, may require the subsequent use of alcohol-based hand sanitizer for maximal disinfection. Further studies will be needed to validate the currently studied disinfectants for use in real-world settings. PMID:29706945

Hand hygiene with soap and water is superior to alcohol rub and antiseptic wipes for removal of Clostridium difficile.

PubMed

Oughton, Matthew T; Loo, Vivian G; Dendukuri, Nandini; Fenn, Susan; Libman, Michael D

2009-10-01

To evaluate common hand hygiene methods for efficacy in removing Clostridium difficile. Randomized crossover comparison among 10 volunteers with hands experimentally contaminated by nontoxigenic C. difficile. Interventions included warm water with plain soap, cold water with plain soap, warm water with antibacterial soap, antiseptic hand wipes, alcohol-based handrub, and a control involving no intervention. All interventions were evaluated for mean reduction in colony-forming units (CFUs) under 2 contamination protocols: "whole hand" and "palmar surface." Results were analyzed according to a Bayesian approach, by using hierarchical models adjusted for multiple observations. Under the whole-hand protocol, the greatest adjusted mean reductions were achieved by warm water with plain soap (2.14 log(10) CFU/mL [95% credible interval (CrI), 1.74-2.54 log(10) CFU/mL]), cold water with plain soap (1.88 log(10) CFU/mL [95% CrI, 1.48-2.28 log(10) CFU/mL), and warm water with antibacterial soap (1.51 log(10) CFU/mL [95% CrI, 1.12-1.91 log(10) CFU/mL]), followed by antiseptic hand wipes (0.57 log(10) CFU/mL [95% CrI, 0.17-0.96 log(10) CFU/mL]). Alcohol-based handrub (0.06 log(10) CFU/mL [95% CrI, -0.34 to 0.45 log(10) CFU/mL]) was equivalent to no intervention. Under the palmar surface protocol, warm water with plain soap, cold water with plain soap, and warm water with antibacterial soap again yielded the greatest mean reductions, followed by antiseptic hand wipes (26.6, 26.6, 26.6, and 21.9 CFUs per plate, respectively), when compared with alcohol-based handrub. Hypothenar (odds ratio, 10.98 [95% CrI, 1.96-37.65]) and thenar (odds ratio, 6.99 [95% CrI, 1.25-23.41]) surfaces were more likely than fingertips to remain heavily contaminated after handwashing. Handwashing with soap and water showed the greatest efficacy in removing C. difficile and should be performed preferentially over the use of alcohol-based handrubs when contact with C. difficile is suspected or likely.

Barriers and Solutions to Fieldwork Education in Hand Therapy.

PubMed

Short, Nathan; Sample, Shelby; Murphy, Malachi; Austin, Brittany; Glass, Jillian

2017-08-09

Survey. Fieldwork education is a vital component of training the next generation of CHTs. Barriers and solutions to fieldwork rotations in hand therapy are examined, as well as proposed solutions, including recommendations for student preparation. This descriptive study examined barriers for certified hand therapist clinicians to accept students for clinical rotations and clinicians' preferences for student preparation before a rotation in a hand setting. A survey was developed, peer reviewed, and distributed using the electronic mailing list of the Hand Therapy Certification Commission via SurveyMonkey. Aggregate responses were analyzed to identify trends including barriers to student clinical rotations and recommendations for students to prepare for hand rotations. A total of 2080 participants responded to the survey, representing a 37% response rate. Common logistical barriers were identified for accepting students such as limited clinical time and space. Many clinicians (32% agree and 8% strongly agree) also felt that the students lack the clinical knowledge to be successful. Areas of knowledge, skill set, and experience were surveyed for development before a clinical rotation in a hand setting. Most respondents (74%) reported increased likelihood of accepting a student with the recommended preparation. Novel qualitative responses to improve clinical experiences are presented as well. Student preparation before a clinical rotation in a hand setting appears to be a significant barrier based on the survey results. Areas of recommended knowledge, skill set, and experience may serve to guide both formal and informal methods of student preparation before a hand-specific clinical rotation to facilitate knowledge translation from experienced certified hand therapists to the next generation. Although logistical barriers may be difficult to overcome, hand-specific preparation based on clinician' recommendations may facilitate student acceptance and success in hand specialty clinical rotations. N/A. Copyright © 2017 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

A qualitative evaluation of hand drying practices among Kenyans.

PubMed

Person, Bobbie; Schilling, Katharine; Owuor, Mercy; Ogange, Lorraine; Quick, Rob

2013-01-01

Recommended disease prevention behaviors of hand washing, hygienic hand drying, and covering one's mouth and nose in a hygienic manner when coughing and sneezing appear to be simple behaviors but continue to be a challenge to successfully promote and sustain worldwide. We conducted a qualitative inquiry to better understand current hand drying behaviors associated with activities of daily living, and mouth and nose covering practices, among Kenyans. We conducted 7 focus group discussions; 30 in-depth interviews; 10 structured household observations; and 75 structured observations in public venues in the urban area of Kisumu; rural communities surrounding Kisumu; and a peri-urban area outside Nairobi, Kenya. Using a grounded theory approach, we transcribed and coded the narrative data followed by thematic analysis of the emergent themes. Hand drying, specifically on a clean towel, was not a common practice among our participants. Most women dried their hands on their waist cloth, called a leso, or their clothes whether they were cooking, eating or cleaning the nose of a young child. If men dried their hands, they used their trousers or a handkerchief. Children rarely dried their hands; they usually just wiped them on their clothes, shook them, or left them wet as they continued with their activities. Many people sneezed into their hands and wiped them on their clothes. Men and women used a handkerchief fairly often when they had a runny nose, cold, or the flu. Most people coughed into the air or their hand. Drying hands on dirty clothes, rags and lesos can compromise the benefits of handwashing. Coughing and sneezing in to an open hand can contribute to spread of disease as well. Understanding these practices can inform health promotion activities and campaigns for the prevention and control of diarrheal disease and influenza.

Digital fringe projection for hand surface coordinate variation analysis caused by osteoarthritis

NASA Astrophysics Data System (ADS)

Nor Haimi, Wan Mokhdzani Wan; Hau Tan, Cheek; Retnasamy, Vithyacharan; Vairavan, Rajendaran; Sauli, Zaliman; Roshidah Yusof, Nor; Hambali, Nor Azura Malini Ahmad; Aziz, Muhammad Hafiz Ab; Bakhit, Ahmad Syahir Ahmad

2017-11-01

Hand osteoarthritis is one of the most common forms of arthritis which impact millions of people worldwide. The disabling problem occurs when the protective cartilage on the boundaries of bones wear off over time. Currently, in order to identify hand osteoarthritis, special instruments namely X-ray scanning and MRI are used for the detection but it also has its limitations such as radiation exposure and can be quite costly. In this work, an optical metrology system based on digital fringe projection which comprises of an LCD projector, CCD camera and a personal computer has been developed to anticipate abnormal growth or deformation on the joints of the hand which are common symptoms of osteoarthritis. The main concept of this optical metrology system is to apply structured light as imaging source for surface change detection. The imaging source utilizes fringe patterns generated by C++ programming and is shifted by 3 phase shifts based on the 3 steps 2 shifts method. Phase wrapping technique and analysis were applied in order to detect the deformation of live subjects. The result has demonstrated a successful method of hand deformation detection based on the pixel tracking differences of a normal and deformed state.

Challenges with mechanical harvesting of blueberries for the fresh market

USDA-ARS?s Scientific Manuscript database

Southern highbush blueberries (SHB) (Vaccinium corymbosum L.) are mostly hand harvested for the fresh market. Hand harvesting of blueberry is labor intensive and costly. Efforts are under way to develop blueberry genotypes that will develop less bruising after impact with hard surfaces on the harv...

Mixing Waters and Moving Ships off the North Carolina Coast

NASA Technical Reports Server (NTRS)

2000-01-01

The estuarine and marine environments of the United States' eastern seaboard provide the setting for a variety of natural and human activities associated with the flow of water. This set of Multi-angle Imaging SpectroRadiometer images from October 11, 2000 (Terra orbit 4344) captures the intricate system of barrier islands, wetlands, and estuaries comprising the coastal environments of North Carolina and southern Virginia. On the right-hand side of the images, a thin line of land provides a tenuous separation between the Albemarle and Pamlico Sounds and the Atlantic Ocean. The wetland communities of this area are vital to productive fisheries and water quality.

The top image covers an area of about 350 kilometers x 260 kilometers and is a true-color view from MISR's 46-degree backward-looking camera. Looking away from the Sun suppresses glint from the reflective water surface and enables mapping the color of suspended sediments and plant life near the coast. Out in the open sea, the dark blue waters indicate the Gulf Stream. As it flows toward the northeast, this ocean current presses close to Cape Hatteras (the pointed cape in the lower portion of the images), and brings warm, nutrient-poor waters northward from equatorial latitudes. North Carolina's Outer Banks are often subjected to powerful currents and storms which cause erosion along the east-facing shorelines. In an effort to save the historic Cape Hatteras lighthouse from the encroaching sea, it was jacked out of the ground and moved about 350 meters in 1999.

The bottom image was created with red band data from the 46-degree backward, 70-degree forward, and 26-degree forward cameras displayed as red, green, and blue, respectively. The color variations in this multi-angle composite indicate different angular (rather than spectral) signatures. Here, the increased reflection of land vegetation at the angle viewing away from the Sun causes a reddish tint. Water, on the other hand, appears predominantly in shades of blue and green due to the bright sunglint captured by the forward-viewing cameras. Contrasting angular signatures, most likely associated with variations in the orientation and slope of wind-driven surface waves, are apparent in the sunglint patterns.

Details of human activities are visible in these images. Near the top center, the Chesapeake Bay Bridge-Tunnel complex, which links Norfolk with Virginia's eastern shore, can be seen. The locations of two tunnels which route automobiles below the water appear as gaps in the visible roadway. In the top image, the small white specks in the open waters of the Atlantic Ocean are ship wakes. The movements of the ships have been visualized by displaying the views from MISR's four backward-viewing cameras in an animated sequence (below). These cameras successively observe the same surface locations over a time interval of about 160 seconds. The large version of the animation covers an area of 135 kilometers x 130 kilometers. The land area on the left-hand side includes the birthplace of aviation, Kitty Hawk, where the Wright Brothers made their first sustained, powered flight in 1903.

[figure removed for brevity, see original site]

MISR was built and is managed by NASA's Jet Propulsion Laboratory, Pasadena, CA, for NASA's Office of Earth Science, Washington, DC. The Terra satellite is managed by NASA's Goddard Space Flight Center, Greenbelt, MD. JPL is a division of the California Institute of Technology.

Using a Standardized Clinical Quantitative Sensory Testing Battery to Judge the Clinical Relevance of Sensory Differences Between Adjacent Body Areas.

PubMed

Dimova, Violeta; Oertel, Bruno G; Lötsch, Jörn

2017-01-01

Skin sensitivity to sensory stimuli varies among different body areas. A standardized clinical quantitative sensory testing (QST) battery, established for the diagnosis of neuropathic pain, was used to assess whether the magnitude of differences between test sites reaches clinical significance. Ten different sensory QST measures derived from thermal and mechanical stimuli were obtained from 21 healthy volunteers (10 men) and used to create somatosensory profiles bilateral from the dorsum of the hands (the standard area for the assessment of normative values for the upper extremities as proposed by the German Research Network on Neuropathic Pain) and bilateral at volar forearms as a neighboring nonstandard area. The parameters obtained were statistically compared between test sites. Three of the 10 QST parameters differed significantly with respect to the "body area," that is, warmth detection, thermal sensory limen, and mechanical pain thresholds. After z-transformation and interpretation according to the QST battery's standard instructions, 22 abnormal values were obtained at the hand. Applying the same procedure to parameters assessed at the nonstandard site forearm, that is, z-transforming them to the reference values for the hand, 24 measurements values emerged as abnormal, which was not significantly different compared with the hand (P=0.4185). Sensory differences between neighboring body areas are statistically significant, reproducing prior knowledge. This has to be considered in scientific assessments where a small variation of the tested body areas may not be an option. However, the magnitude of these differences was below the difference in sensory parameters that is judged as abnormal, indicating a robustness of the QST instrument against protocol deviations with respect to the test area when using the method of comparison with a 95 % confidence interval of a reference dataset.

Effective Scenarios for Exploring Asteroid Surfaces

NASA Astrophysics Data System (ADS)

Clark, Pamela E.; Clark, C.; Weisbin, C.

2010-10-01

In response to the proposal that asteroids be the next targets for exploration, we attempt to develop scenarios for exploring previously mapped asteroid 433 Eros, harnessing our recent experience gained planning such activity for return to the lunar surface. The challenges faced in planning Apollo led to the development of a baseline methodology for extraterrestrial field science. What `lessons learned’ can be applied for asteroids? Effective reconnaissance (advanced mapping at <0.5 m, photos with plotted routes as in-field reference maps), training/simulating/planning (highly interactive abundant field time for extended crew), and documentation (hands-free audio and visual systematic description) procedures are still valid. The use of Constant Scale Natural Boundary rather than standard projection maps eases the challenge of navigating and interpreting a highly irregular object. Lunar and asteroid surfaces are dominated by bombardment and space radiation/dust/charged particle/regolith interactions, with similar implications for sampling. Asteroid work stations are selected on the basis of impact-induced exposure of `outcrops’ from prominent ridges (e.g., Himeros, the noses) potentially representing underlying material, supplemented by sampling of areas of especially thin or deep regolith (ponds). Unlike the Moon, an asteroid lacks sufficient gravity and most likely the necessary stability to support `normal’ driving or walking. In fact, the crew delivery vehicle might not even be `tetherable’ and would most likely `station keep’ to maintain a position. The most convenient local mobility mechanism for astronauts/robots would be `hand over hand’ above the surface at a field station supplemented by a `tetherless’ (small rocket-pack) control system for changing station or return to vehicle. Thus, we assume similar mobility constraints (meters to hundreds of meters at a local station, kilometers between stations) as those used for Apollo. We also assume the vehicle could `station keep’ at more than one location separated by tens of kilometers distance.

Broadleaf deciduous forest counterbalanced the direct effect of climate on Holocene fire regime in hemiboreal/boreal region (NE Europe)

NASA Astrophysics Data System (ADS)

Feurdean, Angelica; Veski, Siim; Florescu, Gabriela; Vannière, Boris; Pfeiffer, Mirjam; O'Hara, Robert B.; Stivrins, Normunds; Amon, Leeli; Heinsalu, Atko; Vassiljev, Jüri; Hickler, Thomas

2017-08-01

Disturbances by fire are essential for the functioning of boreal/hemiboreal forests, but knowledge of long-term fire regime dynamics is limited. We analysed macrocharcoal morphologies and pollen of a sediment record from Lake Lielais Svētiņu (eastern Latvia), and in conjunction with fire traits analysis present the first record of Holocene variability in fire regime, fuel sources and fire types in boreal forests of the Baltic region. We found a phase of moderate to high fire activity during the cool and moist early (mean fire return interval; mFRI of ∼280 years; 11,700-7500 cal yr BP) and the late (mFRI of ∼190 years; 4500-0 cal yr BP) Holocene and low fire activity (mFRI of ∼630 years) during the Holocene Thermal Optimum (7500-4500 cal yr BP). Charcoal morphotypes and the pollen record show the predominance of frequent surface fires, occasionally transitioning to the crown during Pinus sylvestris-Betula boreal forests and less frequent surface fires during the dominance of temperate deciduous forests. In contrast to the prevailing opinion that fires in boreal forests are mostly low to moderate severity surface fires, we found evidence for common occurrence of stand-replacing crown fires in Picea abies canopy. Our results highlight that charcoal morphotypes analysis allows for distinguishing the fuel types and surface from crown fires, therefore significantly advancing our interpretation of fire regime. Future warmer temperatures and increase in the frequency of dry spells and abundant biomass accumulation can enhance the fire risk on the one hand, but will probably promote the expansion of broadleaf deciduous forests to higher latitudes, on the other hand. By highlighting the capability of broadleaf deciduous forests to act as fire-suppressing landscape elements, our results suggest that fire activity may not increase in the Baltic area under future climate change.

Development of monitoring and modelling tools as basis for sustainable thermal management concepts of urban groundwater bodies

NASA Astrophysics Data System (ADS)

Mueller, Matthias H.; Epting, Jannis; Köhler, Mandy; Händel, Falk; Huggenberger, Peter

2015-04-01

Increasing groundwater temperatures observed in many urban areas strongly interfere with the demand of thermal groundwater use. The groundwater temperatures in these urban areas are affected by numerous interacting factors: open and closed-loop geothermal systems for heating and cooling, sealed surfaces, constructions in the subsurface (infrastructure and buildings), artificial groundwater recharge, and interaction with rivers. On the one hand, these increasing groundwater temperatures will negatively affect the potential for its use in the future e.g. for cooling purposes. On the other hand, elevated subsurface temperatures can be considered as an energy source for shallow geothermal heating systems. Integrated thermal management concepts are therefore needed to coordinate the thermal use of groundwater in urban areas. These concepts should be based on knowledge of the driving processes which influence the thermal regime of the aquifer. We are currently investigating the processes influencing the groundwater temperature throughout the urban area of Basel City, Switzerland. This involves a three-dimensional numerical groundwater heat-transport model including geothermal use and interactions with the unsaturated zone such as subsurface constructions reaching into the aquifer. The cantonal groundwater monitoring system is an important part of the data base in our model, which will help to develop sustainable management strategies. However, single temperature measurements in conventional groundwater wells can be biased by vertical thermal convection. Therefore, multilevel observation wells are used in the urban areas of the city to monitor subsurface temperatures reaching from the unsaturated zone to the base of the aquifer. These multilevel wells are distributed in a pilot area in order to monitor the subsurface temperatures in the vicinity of deep buildings and to quantify the influence of the geothermal use of groundwater. Based on time series of the conventional groundwater wells, the multilevel observation wells and the different boundary conditions we characterize the groundwater temperature regimes using a regional groundwater heat-transport model. In the urban area of Basel, mean annual groundwater temperatures are significantly increasing with 0.05 K per year in the period of 1994 to 2014, which is most likely due to anthropogenic influences. Overall, mean annual groundwater temperatures of Basel are 3.0