Science.gov

Sample records for handling machine mhm

  1. FEMA and RAM Analysis for the Multi Canister Overpack (MCO) Handling Machine

    SciTech Connect

    SWENSON, C.E.

    2000-06-01

    The Failure Modes and Effects Analysis and the Reliability, Availability, and Maintainability Analysis performed for the Multi-Canister Overpack Handling Machine (MHM) has shown that the current design provides for a safe system, but the reliability of the system (primarily due to the complexity of the interlocks and permissive controls) is relatively low. No specific failure modes were identified where significant consequences to the public occurred, or where significant impact to nearby workers should be expected. The overall reliability calculation for the MHM shows a 98.1 percent probability of operating for eight hours without failure, and an availability of the MHM of 90 percent. The majority of the reliability issues are found in the interlocks and controls. The availability of appropriate spare parts and maintenance personnel, coupled with well written operating procedures, will play a more important role in successful mission completion for the MHM than other less complicated systems.

  2. Evaluation of Multi Canister Overpack (MCO) Handling Machine Uplift Restraint for a Seismic Event During Repositioning Operations

    SciTech Connect

    SWENSON, C.E.

    2000-05-15

    Insertion of the Multi-Canister Overpack (MCO) assemblies into the Canister Storage Building (CSB) storage tubes involves the use of the MCO Handling Machine (MHM). During MCO storage tube insertion operations, inadvertent movement of the MHM is prevented by engaging seismic restraints (''active restraints'') located adjacent to both the bridge and trolley wheels. During MHM repositioning operations, the active restraints are not engaged. When the active seismic restraints are not engaged, the only functioning seismic restraints are non-engageable (''passive'') wheel uplift restraints which function only if the wheel uplift is sufficient to close the nominal 0.5-inch gap at the uplift restraint interface. The MHM was designed and analyzed in accordance with ASME NOG-1-1995. The ALSTHOM seismic analysis reported seismic loads on the MHM uplift restraints and EDERER performed corresponding structural calculations to demonstrate structural adequacy of the seismic uplift restraint hardware. The ALSTHOM and EDERER calculations were performed for a parked MHM with the active seismic restraints engaged, resulting in uplift restraint loading only in the vertical direction. In support of development of the CSB Safety Analysis Report (SAR), an evaluation of the MHM seismic response was requested for the case where the active seismic restraints are not engaged. If a seismic event occurs during MHM repositioning operations, a moving contact at a seismic uplift restraint would introduce a friction load on the restraint in the direction of the movement. These potential horizontal friction loads on the uplift restraints were not included in the existing restraint hardware design calculations. One of the purposes of the current evaluation is to address the structural adequacy of the MHM seismic uplift restraints with the addition of the horizontal friction associated with MHM repositioning movements.

  3. Multi Canister Overpack (MCO) Handling Machine Independent Review of Seismic Structural Analysis

    SciTech Connect

    SWENSON, C.E.

    2000-09-22

    The following separate reports and correspondence pertains to the independent review of the seismic analysis. The original analysis was performed by GEC-Alsthom Engineering Systems Limited (GEC-ESL) under subcontract to Foster-Wheeler Environmental Corporation (FWEC) who was the prime integration contractor to the Spent Nuclear Fuel Project for the Multi-Canister Overpack (MCO) Handling Machine (MHM). The original analysis was performed to the Design Basis Earthquake (DBE) response spectra using 5% damping as required in specification, HNF-S-0468 for the 90% Design Report in June 1997. The independent review was performed by Fluor-Daniel (Irvine) under a separate task from their scope as Architect-Engineer of the Canister Storage Building (CSB) in 1997. The comments were issued in April 1998. Later in 1997, the response spectra of the Canister Storage Building (CSB) was revised according to a new soil-structure interaction analysis and accordingly revised the response spectra for the MHM and utilized 7% damping in accordance with American Society of Mechanical Engineers (ASME) NOG-1, ''Rules for Construction of Overhead and Gantry Cranes (Top Running Bridge, Multiple Girder).'' The analysis was re-performed to check critical areas but because manufacturing was underway, designs were not altered unless necessary. FWEC responded to SNF Project correspondence on the review comments in two separate letters enclosed. The dispositions were reviewed and accepted. Attached are supplier source surveillance reports on the procedures and process by the engineering group performing the analysis and structural design. All calculation and analysis results are contained in the MHM Final Design Report which is part of the Vendor Information File 50100. Subsequent to the MHM supplier engineering analysis, there was a separate analyses for nuclear safety accident concerns that used the electronic input data files provided by FWEC/GEC-ESL and are contained in document SNF-6248

  4. Multi Canister Overpack (MCO) Handling Machine Trolley Seismic Uplift Constraint Design Loads

    SciTech Connect

    SWENSON, C.E.

    2000-03-09

    The MCO Handling Machine (MHM) trolley moves along the top of the MHM bridge girders on east-west oriented rails. To prevent trolley wheel uplift during a seismic event, passive uplift constraints are provided as shown in Figure 1-1. North-south trolley wheel movement is prevented by flanges on the trolley wheels. When the MHM is positioned over a Multi-Canister Overpack (MCO) storage tube, east-west seismic restraints are activated to prevent trolley movement during MCO handling. The active seismic constraints consist of a plunger, which is inserted into slots positioned along the tracks as shown in Figure 1-1. When the MHM trolley is moving between storage tube positions, the active seismic restraints are not engaged. The MHM has been designed and analyzed in accordance with ASME NOG-1-1995. The ALSTHOM seismic analysis (Reference 3) reported seismic uplift restraint loading and EDERER performed corresponding structural calculations. The ALSTHOM and EDERER calculations were performed with the east-west seismic restraints activated and the uplift restraints experiencing only vertical loading. In support of development of the CSB Safety Analysis Report (SAR), an evaluation of the MHM seismic response was requested for the case where the east-west trolley restraints are not engaged. For this case, the associated trolley movements would result in east-west lateral loads on the uplift constraints due to friction, as shown in Figure 1-2. During preliminary evaluations, questions were raised as to whether the EDERER calculations considered the latest ALSTHOM seismic analysis loads (See NCR No. 00-SNFP-0008, Reference 5). Further evaluation led to the conclusion that the EDERER calculations used appropriate vertical loading, but the uplift restraints would need to be re-analyzed and modified to account for lateral loading. The disposition of NCR 00-SNFP-0008 will track the redesign and modification effort. The purpose of this calculation is to establish bounding seismic

  5. Effect of coating over the handle of a drill machine on vibration transmissibility.

    PubMed

    Singh, Jagvir; Khan, Abid Ali

    2014-03-01

    This study was to see the effect of different coatings on the handle of hand-held drilling machines. Out of five different handles chosen for this study, including one handle uncoated. Root mean square (rms) values of the vibration levels (acceleration) were recorded at the surface of handle and wrist of the operators. Results showed that maximum vibrations were reduced by coating of handle coated with rubber sheet and Rexene (H4) followed by handle coated with cotton sandwiched between jeans cloth (H5). Equivalent vibrations transmitted through coating of handles coated with sponge and velvet (H2) and jute and cotton (H3) were of almost same magnitude and these two coated handles were able to reduce least vibration transmitted. Transmissibility of vibrations along dominant (Z) direction was analyzed using ANOVA. Results showed that coating on handles significantly affected vibration transmitted in Z direction. Vibration transmissibility ratios were found to be 0.354, 0.571, 0.408, 0.4326, and 0.3555 for handles H1, H2, H3, H4 and H5 respectively. PMID:23642474

  6. Integrated digital control and man-machine interface for complex remote handling systems

    SciTech Connect

    Rowe, J.C.; Spille, R.F.; Zimmermann, S.D.

    1986-12-01

    The Advanced Integrated Maintenance System (AIMS) is part of a continuing effort within the Consolidated Fuel Reprocessing Program at Oak Ridge National Laboratory to develop and extend the capabilities of remote manipulation and maintenance technology. The AIMS is a totally integrated approach to remote handling in hazardous environments. State-of-the-art computer systems connected through a high-speed communication network provide a real-time distributed control system that supports the flexibility and expandability needed for large integrated maintenance applications. A Man-Machine Interface provides high-level human interaction through a powerful color graphics menu-controlled operator console. An auxiliary control system handles the real-time processing needs for a variety of support hardware. A pair of dedicated fiber-optic-linked master/slave computer system control the Advanced Servomanipulator master/slave arms using powerful distributed digital processing methods. The FORTH language was used as a real-time operating and development environment for the entire system, and all of these components are integrated into a control room concept that represents the latest advancements in the development of remote maintenance facilities for hazardous environments.

  7. Streamflow data assimilation for the mesoscale hydrologic model (mHM) using particle filtering

    NASA Astrophysics Data System (ADS)

    Noh, Seong Jin; Rakovec, Oldrich; Kumar, Rohini; Samaniego, Luis; Choi, Shin-woo

    2015-04-01

    Data assimilation has been becoming popular to increase the certainty of the hydrologic prediction considering various sources of uncertainty through the hydrologic modeling chain. In this study, we develop a data assimilation framework for the mesoscale hydrologic model (mHM 5.2, http://www.ufz.de/mhm) using particle filtering, which is a sequential DA method for non-linear and non-Gaussian models. The mHM is a grid based distributed model that is based on numerical approximations of dominant hydrologic processes having similarity with the HBV and VIC models. The developed DA framework for the mHM represents simulation uncertainty by model ensembles and updates spatial distributions of model state variables when new observations are available in each updating time interval. The evaluation of the proposed method is carried out within several large European basins via assimilating multiple streamflow measurements in a daily interval. Dimensional limitations of particle filtering is resolved by effective noise specification methods, which uses spatial and temporal correlation of weather forcing data to represent model structural uncertainty. The presentation will be focused on gains and limitations of streamflow data assimilation in several hindcasting experiments. In addition, impacts of non-Gaussian distributions of state variables on model performance will be discussed.

  8. An open-source distributed mesoscale hydrologic model (mHM)

    NASA Astrophysics Data System (ADS)

    Samaniego, Luis; Kumar, Rohini; Zink, Matthias; Thober, Stephan; Mai, Juliane; Cuntz, Matthias; Schäfer, David; Schrön, Martin; Musuuza, Jude; Prykhodko, Vladyslav; Dalmasso, Giovanni; Attinger, Sabine; Spieler, Diana; Rakovec, Oldrich; Craven, John; Langenberg, Ben

    2014-05-01

    The mesoscale hydrological model (mHM) is based on numerical approximations of dominant hydrological processes that have been tested in various hydrological models such as: HBV and VIC. In general, mHM simulates the following processes: canopy interception, snow accumulation and melting, soil moisture dynamics (n-horizons), infiltration and surface runoff, evapotranspiration, subsurface storage and discharge generation, deep percolation and baseflow, and discharge attenuation and flood routing. The main characteristic of mHM is the treatment of the sub-grid variability of input variables and model parameters which clearly distinguishes this model from existing precipitation-runoff models or land surface models. It uses a Multiscale Parameter Regionalization (MPR) to account for the sub-grid variability and to avoid continuous re-calibration. Effective model parameters are location and time dependent (e.g., soil porosity). They are estimated through upscaling operators that link sub-grid morphologic information (e.g., soil texture) with global transfer-function parameters, which, in turn, are found through multi-basin optimization. Global parameters estimated with the MPR technique are quasi-scale invariant and guarantee flux-matching across scales. mHM is an open source code, written in Fortran 2003 (standard), fully modular, with high computational efficiency, and parallelized. It is portable to multiple platforms (Linux, OS X, Windows) and includes a number of algorithms for sensitivity analysis, analysis of parameter uncertainty (MCMC), and optimization (DDS, SA, SCE). All simulated state variables and outputs can be stored as netCDF files for further analysis and visualization. mHM has been evaluated in all major river basins in Germany and over 80 US and 250 European river basins. The model efficiency (NSE) during validation at proxy locations is on average greater than 0.6. During last years, mHM had been used for number of hydrologic applications such as

  9. Soil Moisture at Intermediate Scales: Linking Cosmic Ray Measurements with the Hydrologic Model mHM

    NASA Astrophysics Data System (ADS)

    Schrön, M.; Zacharias, S.; Samaniego, L. E.; Dietrich, P.

    2013-12-01

    Measuring soil moisture with Cosmic Ray Sensors (CRS) is an emerging field of research, because the mesoscale footprint (~0.3 km^2) is of great interest for land surface models that usually work at resolutions ranging between point measurements (e.g. TDR) and remote sensing data. We run Cosmic Ray Sensors in the small catchment "Schäfertal" (1.4 km^2) in the lower Harz Mountains, central Germany. Simultaneously, the mesoscale Hydrologic Model (mHM) [Samaniego et al. 2010] is set up for the small catchment scale for the first time. We aim (1) to find crucial spots in the field with high variability of soil moisture in order to effectively place the static sensors with the support of the model, (2) to improve soil moisture calibration and evaluation in mHM with the support of the intermediate-scale soil moisture information from the CRS. The novel key of this approach is the synergy of mesoscale soil moisture measurements and the parameterization of the hydrologic model. This work prepares upcoming projects with mobile Cosmic Ray Sensors on a rover, which have a great potential to enlarge the measurement area up to scales of remote sensing footprints. References: Samaniego, L., Kumar, R., & Attinger, S. (2010). Multiscale parameter regionalization of a grid-based hydrologic model at the mesoscale. Water Resources Research, 46(5), 1-25. doi:10.1029/2008WR007327 Zreda, M., Shuttleworth, W. J., Zeng, X., Zweck, C., Desilets, D., Franz, T., & Rosolem, R. (2012). COSMOS: the COsmic-ray Soil Moisture Observing System. Hydrology and Earth System Sciences, 16(11), 4079-4099. doi:10.5194/hess-16-4079-2012

  10. Modelling Nitrate uptake in river networks using the new mHM water quality model

    NASA Astrophysics Data System (ADS)

    Yang, Xiaoqiang; Sinha, Sumit; Samaniego, Luis; Kumar, Rohini; Jomaa, Seifeddine; Rode, Michael

    2016-04-01

    To understand the spatial distribution and temporal dynamics of nitrate uptake in river networks under different land use are critical for the protection of river ecosystem and drinking water supply. To this end, distributed grid-based hydrological water quality models are required. The multi-scale Hydrological Model (mHM) was integrated with the nitrate transport and reaction (NTR) routines. The main equations of NTR routines were introduced from the HYPE (Hydrological Predictions for the Environment) model, which has been fully verified in the literature. The new coupled mHM model with the NTR routines is able to calculate the hydrographs at any point and also the distribution of state variables, which makes it possible to present the distribution of inorganic nitrogen uptake in the whole river network. First, the model is successfully calibrated and validated in the Selke catchment (463 km2) using three gauging stations during the period of 1994-2004 in terms of hydrographs and inorganic nitrogen concentrations. Then, the model performance for in-stream Nitrate uptake predictions are presented and analyzed temporally and spatially, considering the Selke river network characteristics. Particularly, how much the land use affects the amount and the intra-annual dynamics of in-stream uptake are discussed using one forest-dominant sub-catchment (Meisdorf, where forest share is about 72%) with another agriculture-dominant sub-catchment (Hausneindorf, where agriculture share is about 76%). In addition, the seasonal variation of model in-stream nitrate uptake predictions are compared with calculated values using the nitrate assimilatory uptake approach generated from high frequency sensor measurements.

  11. Transcripts of the MHM region on the chicken Z chromosome accumulate as non-coding RNA in the nucleus of female cells adjacent to the DMRT1 locus.

    PubMed

    Teranishi, M; Shimada, Y; Hori, T; Nakabayashi, O; Kikuchi, T; Macleod, T; Pym, R; Sheldon, B; Solovei, I; Macgregor, H; Mizuno, S

    2001-01-01

    The male hypermethylated (MHM) region, located near the middle of the short arm of the Z chromosome of chickens, consists of approximately 210 tandem repeats of a BamHI 2.2-kb sequence unit. Cytosines of the CpG dinucleotides of this region are extensively methylated on the two Z chromosomes in the male but much less methylated on the single Z chromosome in the female. The state of methylation of the MHM region is established after fertilization by about the 1-day embryonic stage. The MHM region is transcribed only in the female from the particular strand into heterogeneous, high molecular-mass, non-coding RNA, which is accumulated at the site of transcription, adjacent to the DMRT1 locus, in the nucleus. The transcriptional silence of the MHM region in the male is most likely caused by the CpG methylation, since treatment of the male embryonic fibroblasts with 5-azacytidine results in hypo-methylation and active transcription of this region. In ZZW triploid chickens, MHM regions are hypomethylated and transcribed on the two Z chromosomes, whereas MHM regions are hypermethylated and transcriptionally inactive on the three Z chromosomes in ZZZ triploid chickens, suggesting a possible role of the W chromosome on the state of the MHM region. PMID:11321370

  12. Employing satellite retrieved soil moisture for parameter estimation of the hydrologic model mHM

    NASA Astrophysics Data System (ADS)

    Zink, Matthias; Mai, Juliane; Rakovec, Oldrich; Schrön, Martin; Kumar, Rohini; Schäfer, David; Samaniego, Luis

    2016-04-01

    Hydrological models are usually calibrated against observed streamflow at the catchment outlet and thus they are conditioned by an integral catchment signal. Rakovec et al. 2016 (JHM) recently demonstrated that constraining model parameters against river discharge is a necessary, but not a sufficient condition. Such a procedure ensures the fulfillment of the catchment's water balance but can lead to high predictive uncertainties of model internal states, like soil moisture, or a lack in spatial representativeness of the model. However, some hydrologic applications, as e.g. soil drought monitoring and prediction, rely on this information. Within this study we propose a framework in which the mesoscale Hydrologic Model (mHM) is calibrated with soil moisture retrievals from various sources. The aim is to condition the model on soil moisture (SM), while preserving good performance in streamflow estimation. We identify the most appropriate objective functions by conducting synthetic experiments. The best objective function is determined based on: 1) deviation between synthetic and simulated soil moisture, 2) nonparametric comparison of SM fields (e.g. copulas), and 3) by euclidian distance of model parameters, which is zero if the parameters of the synthetic data are recovered. Those objective functions performing best are used to calibrate mHM against different satellite soil moisture products, e.g. ESA-CCI, H-SAF, and in situ observations. This procedure is tested in three distinct European basins (upper Sava, Neckar, and upper Guadalquivir basin) ranging from snow domination to semi arid climatic conditions. Results obtained with the synthetic experiment indicate that objective functions focusing on the temporal dynamics of SM are preferable to objective functions aiming at spatial patterns or catchment averages. Since the deviation of soil moisture fields (1) and their copulas (2) don't lead to conclusive results, the decision of the best performing objective

  13. Streamflow hindcasting in European river basins via multi-parametric ensemble of the mesoscale hydrologic model (mHM)

    NASA Astrophysics Data System (ADS)

    Noh, Seong Jin; Rakovec, Oldrich; Kumar, Rohini; Samaniego, Luis

    2016-04-01

    There have been tremendous improvements in distributed hydrologic modeling (DHM) which made a process-based simulation with a high spatiotemporal resolution applicable on a large spatial scale. Despite of increasing information on heterogeneous property of a catchment, DHM is still subject to uncertainties inherently coming from model structure, parameters and input forcing. Sequential data assimilation (DA) may facilitate improved streamflow prediction via DHM using real-time observations to correct internal model states. In conventional DA methods such as state updating, parametric uncertainty is, however, often ignored mainly due to practical limitations of methodology to specify modeling uncertainty with limited ensemble members. If parametric uncertainty related with routing and runoff components is not incorporated properly, predictive uncertainty by DHM may be insufficient to capture dynamics of observations, which may deteriorate predictability. Recently, a multi-scale parameter regionalization (MPR) method was proposed to make hydrologic predictions at different scales using a same set of model parameters without losing much of the model performance. The MPR method incorporated within the mesoscale hydrologic model (mHM, http://www.ufz.de/mhm) could effectively represent and control uncertainty of high-dimensional parameters in a distributed model using global parameters. In this study, we present a global multi-parametric ensemble approach to incorporate parametric uncertainty of DHM in DA to improve streamflow predictions. To effectively represent and control uncertainty of high-dimensional parameters with limited number of ensemble, MPR method is incorporated with DA. Lagged particle filtering is utilized to consider the response times and non-Gaussian characteristics of internal hydrologic processes. The hindcasting experiments are implemented to evaluate impacts of the proposed DA method on streamflow predictions in multiple European river basins

  14. Comments on Frequency Swept Rotating Input Perturbation Techniques and Identification of the Fluid Force Models in Rotor/bearing/seal Systems and Fluid Handling Machines

    NASA Technical Reports Server (NTRS)

    Muszynska, Agnes; Bently, Donald E.

    1991-01-01

    Perturbation techniques used for identification of rotating system dynamic characteristics are described. A comparison between two periodic frequency-swept perturbation methods applied in identification of fluid forces of rotating machines is presented. The description of the fluid force model identified by inputting circular periodic frequency-swept force is given. This model is based on the existence and strength of the circumferential flow, most often generated by the shaft rotation. The application of the fluid force model in rotor dynamic analysis is presented. It is shown that the rotor stability is an entire rotating system property. Some areas for further research are discussed.

  15. Kidney Injury Molecule-1 Is Specifically Expressed in Cystically-Transformed Proximal Tubules of the PKD/Mhm (cy/+) Rat Model of Polycystic Kidney Disease

    PubMed Central

    Gauer, Stefan; Urbschat, Anja; Gretz, Norbert; Hoffmann, Sigrid C.; Kränzlin, Bettina; Geiger, Helmut; Obermüller, Nicholas

    2016-01-01

    Expression of kidney injury molecule-1 (Kim-1) is rapidly upregulated following tubular injury, constituting a biomarker for acute kidney damage. We examined the renal localization of Kim-1 expression in PKD/Mhm (polycystic kidney disease, Mannheim) (cy/+) rats (cy: mutated allel, +: wild type allel), an established model for autosomal dominant polycystic kidney disease, with chronic, mainly proximal tubulointerstitial alterations. For immunohistochemistry or Western blot analysis, kidneys of male adult heterozygously-affected (cy/+) and unaffected (+/+) littermates were perfusion-fixed or directly removed. Kim-1 expression was determined using peroxidase- or fluorescence-linked immunohistochemistry (alone or in combination with markers for tubule segments or differentiation). Compared to (+/+), only in (cy/+) kidneys, a chronic expression of Kim-1 could be detected by Western blot analysis, which was histologically confined to an apical cellular localization in areas of cystically-transformed proximal tubules with varying size and morphology, but not in distal tubular segments. Kim-1 was expressed by cystic epithelia exhibiting varying extents of dedifferentiation, as shown by double labeling with aquaporin-1, vimentin or osteopontin, yielding partial cellular coexpression. In this model, in contrast to other known molecules indicating renal injury and/or repair mechanisms, the chronic renal expression of Kim-1 is strictly confined to proximal cysts. Its exact role in interfering with tubulo-interstitial alterations in polycystic kidney disease warrants future investigations. PMID:27231899

  16. Kidney Injury Molecule-1 Is Specifically Expressed in Cystically-Transformed Proximal Tubules of the PKD/Mhm (cy/+) Rat Model of Polycystic Kidney Disease.

    PubMed

    Gauer, Stefan; Urbschat, Anja; Gretz, Norbert; Hoffmann, Sigrid C; Kränzlin, Bettina; Geiger, Helmut; Obermüller, Nicholas

    2016-01-01

    Expression of kidney injury molecule-1 (Kim-1) is rapidly upregulated following tubular injury, constituting a biomarker for acute kidney damage. We examined the renal localization of Kim-1 expression in PKD/Mhm (polycystic kidney disease, Mannheim) (cy/+) rats (cy: mutated allel, +: wild type allel), an established model for autosomal dominant polycystic kidney disease, with chronic, mainly proximal tubulointerstitial alterations. For immunohistochemistry or Western blot analysis, kidneys of male adult heterozygously-affected (cy/+) and unaffected (+/+) littermates were perfusion-fixed or directly removed. Kim-1 expression was determined using peroxidase- or fluorescence-linked immunohistochemistry (alone or in combination with markers for tubule segments or differentiation). Compared to (+/+), only in (cy/+) kidneys, a chronic expression of Kim-1 could be detected by Western blot analysis, which was histologically confined to an apical cellular localization in areas of cystically-transformed proximal tubules with varying size and morphology, but not in distal tubular segments. Kim-1 was expressed by cystic epithelia exhibiting varying extents of dedifferentiation, as shown by double labeling with aquaporin-1, vimentin or osteopontin, yielding partial cellular coexpression. In this model, in contrast to other known molecules indicating renal injury and/or repair mechanisms, the chronic renal expression of Kim-1 is strictly confined to proximal cysts. Its exact role in interfering with tubulo-interstitial alterations in polycystic kidney disease warrants future investigations. PMID:27231899

  17. 8. VIEW OF THE MACHINE SHOP. BY 1966, THE MACHINE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    8. VIEW OF THE MACHINE SHOP. BY 1966, THE MACHINE SHOP HANDLED PRIMARILY STAINLESS STEEL COMPONENTS, WHICH WERE SENT TO THE MACHINE SHOP TO BE FORMED INTO THEIR FINAL SHAPES. (7/24/70) - Rocky Flats Plant, General Manufacturing, Support, Records-Central Computing, Southern portion of Plant, Golden, Jefferson County, CO

  18. Distributed nitrate transport and reaction routines (NTR) inside the mesoscale Hydrological Model (mHM) framework: Development and Application in the Selke catchment

    NASA Astrophysics Data System (ADS)

    Sinha, Sumit; Rode, Michael; Kumar, Rohini; Yang, Xiaoqiang; Samaniego, Luis; Borchardt, Dietrich

    2016-04-01

    Precise measurements of where, when and how much denitrification occurs on the basis of measurements alone persist to be vexing and intractable research problem at all spatial and temporal scales. As a result, models have become essential and vital tools for furthering our current understanding of the processes that control denitrification on catchment scale. Emplacement of Water Framework Directive (WFD) and continued efforts in improving water treatment facilities has resulted in alleviating the problems associated with point sources of pollution. However, the problem of eutrophication still persists and is primarily associated with the diffused sources of pollution originating from agricultural area. In this study, the nitrate transport and reaction (NTR) routines are developed inside the distributed mesoscale Hydrological Model (mHM www.ufz.de/mhm) which is a fully distributed hydrological model with a novel parameter regionalization scheme (Samaniego et al. 2010; Kumar et al. 2013) and has been applied to whole Europe (Rakovec et al. 2016) and numerous catchments worldwide. The aforementioned NTR model is applied to a mesoscale river basin, Selke (463 km2) located in central Germany. The NTR model takes in account the critical and pertinent processes like transformation in vadose zone, atmospheric deposition, plant uptake, instream denitrification and also simulates the process of manure and fertilizer application. Both streamflow routines and the NTR model are run on daily time steps. The split-sample approach was used for model calibration (1994-1999) and validation (2000-2004). Flow dynamics at three gauging stations located inside this catchment are successfully captured by the model with consistently high Nash-Sutcliffe Efficiency (NSE) of at least 0.8. Regarding nitrate estimates, the NSE values are greater than 0.7 for both validation and calibration periods. Finally, the NTR model is used for identifying the critical source areas (CSAs) that contribute

  19. 4. VIEW LOOKING NORTHWEST OF FUEL HANDLING BUILDING (CENTER), REACTOR ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. VIEW LOOKING NORTHWEST OF FUEL HANDLING BUILDING (CENTER), REACTOR SERVICE BUILDING (RIGHT), MACHINE SHOP (LEFT) - Shippingport Atomic Power Station, On Ohio River, 25 miles Northwest of Pittsburgh, Shippingport, Beaver County, PA

  20. Transportation and handling loads

    NASA Technical Reports Server (NTRS)

    Ostrem, F. E.

    1971-01-01

    Criteria and recommended practices are presented for the prediction and verification of transportation and handling loads for the space vehicle structure and for monitoring these loads during transportation and handling of the vehicle or major vehicle segments. Elements of the transportation and handling systems, and the forcing functions and associated loads are described. The forcing functions for common carriers and typical handling devices are assessed, and emphasis is given to the assessment of loads at the points where the space vehicle is supported during transportation and handling. Factors which must be considered when predicting the loads include the transportation and handling medium; type of handling fixture; transport vehicle speed; types of terrain; weather (changes in pressure of temperature, wind, etc.); and dynamics of the transportation modes or handling devices (acceleration, deceleration, and rotations of the transporter or handling device).

  1. Machine Shop Grinding Machines.

    ERIC Educational Resources Information Center

    Dunn, James

    This curriculum manual is one in a series of machine shop curriculum manuals intended for use in full-time secondary and postsecondary classes, as well as part-time adult classes. The curriculum can also be adapted to open-entry, open-exit programs. Its purpose is to equip students with basic knowledge and skills that will enable them to enter the…

  2. Sprag Handle Wrenches

    NASA Technical Reports Server (NTRS)

    Vranishm, John M.

    2010-01-01

    Sprag handle wrenches have been proposed for general applications in which conventional pawl-and-ratchet wrenches and sprag and cam "clickless" wrenches are now used. Sprag handle wrenches are so named because they would include components that would function both as parts of handles and as sprags (roller locking/unlocking components). In comparison with all of the aforementioned conventional wrenches, properly designed sprag handle wrenches could operate with much less backlash; in comparison with the conventional clickless wrenches, sprag handle wrenches could be stronger and less expensive (because the sprags would be larger and more easily controllable than are conventional sprags and cams).

  3. Handling sharps and needles

    MedlinePlus

    ... at: www.cdc.gov/sharpssafety/pdf/sharpsworkbook_2008.pdf . Accessed October 27, 2015. Occupational Safety and Health Administration. OSHA fact sheet: protecting yourself when handling contaminated ...

  4. Grain Handling and Storage.

    ERIC Educational Resources Information Center

    Harris, Troy G.; Minor, John

    This text for a secondary- or postecondary-level course in grain handling and storage contains ten chapters. Chapter titles are (1) Introduction to Grain Handling and Storage, (2) Elevator Safety, (3) Grain Grading and Seed Identification, (4) Moisture Control, (5) Insect and Rodent Control, (6) Grain Inventory Control, (7) Elevator Maintenance,…

  5. Data Handling and Citizenship

    ERIC Educational Resources Information Center

    Tresidder, Gwen

    2006-01-01

    When marking GCSE data handling coursework, the author was repeatedly reminded just how poor the level of statistical understanding is among students. In response to a feeling that the teaching of handling data topics was limited, the author and her colleague designed a project with Y8 students to try to teach statistics for a deeper…

  6. 20. MACHINE SHOP, LOOKING SOUTH. SHOP IS EQUIPPED WITH A ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. MACHINE SHOP, LOOKING SOUTH. SHOP IS EQUIPPED WITH A 25-TON SHAW CRANE TO HANDLE PARTS FROM RAIL CARS INTO THE SHOP. MACHINE SHOP HANDLES ALL NECESSARY REPAIR WORK ON THE DOCK MACHINERY. - Pennsylvania Railway Ore Dock, Lake Erie at Whiskey Island, approximately 1.5 miles west of Public Square, Cleveland, Cuyahoga County, OH

  7. Machine coolant waste reduction by optimizing coolant life. Project summary

    SciTech Connect

    Pallansch, J.

    1995-08-01

    The project was designed to study the following: A specific water-soluble coolant (Blasocut 2000 Universal) in use with a variety of machines, tools, and materials; Coolant maintenance practices associated with three types of machines; Health effects of use and handling of recycled coolant; Handling practices for chips and waste coolant; Chip/coolant separation; and Oil/water separation.

  8. Gradient boosting machines, a tutorial

    PubMed Central

    Natekin, Alexey; Knoll, Alois

    2013-01-01

    Gradient boosting machines are a family of powerful machine-learning techniques that have shown considerable success in a wide range of practical applications. They are highly customizable to the particular needs of the application, like being learned with respect to different loss functions. This article gives a tutorial introduction into the methodology of gradient boosting methods with a strong focus on machine learning aspects of modeling. A theoretical information is complemented with descriptive examples and illustrations which cover all the stages of the gradient boosting model design. Considerations on handling the model complexity are discussed. Three practical examples of gradient boosting applications are presented and comprehensively analyzed. PMID:24409142

  9. Remote Handling System for Ignitor^*

    NASA Astrophysics Data System (ADS)

    Galbiati, L.; Bianchi, A.; Lucca, F.; Coppi, B.

    2005-10-01

    Since access in Ignitor is through the limited width of the equatorial ports, the use of remote handling (RH) technology for any in-vessel intervention is required, even before the vessel becomes activated. In particular, the first wall of Ignitor, which is made of TZM (Molybdenum) tiles mounted on Inconel tile-carriers covering the entire plasma chamber, has been designed to be installed and replaced entirely by the RH system. The presence of radiation screens inside the cryostat and around the ports ensure a sufficiently low level of activation around the machine to avoid the need of ex-vessel RH techniques. The in-vessel RH system is based on two transporters carrying an articulated boom with end-effectors, supported by a movable structure over a transport system that can be lifted and set in position adjacent to two opposite horizontal ports. The design of the in-vessel RH system, of the boom and its enclosure, and of the most significant end-effectors (welding and cutting tools, and tools for the removal and handling of tile carriers) has been completed. A series of other dedicated tools for installation and maintainances of diagnostics components, of the RF antennas, vacuum cleaners, tools for general inspection and metrology are included in the design. ^*Sponsored in part by ENEA of Italy and by the U.S. DOE.

  10. Exception handling controllers: An application of pushdown systems to discrete event control

    SciTech Connect

    Griffin, Christopher H

    2008-01-01

    Recent work by the author has extended the Supervisory Control Theory to include the class of control languages defined by pushdown machines. A pushdown machine is a finite state machine extended by an infinite stack memory. In this paper, we define a specific type of deterministic pushdown machine that is particularly useful as a discrete event controller. Checking controllability of pushdown machines requires computing the complement of the controller machine. We show that Exception Handling Controllers have the property that algorithms for taking their complements and determining their prefix closures are nearly identical to the algorithms available for finite state machines. Further, they exhibit an important property that makes checking for controllability extremely simple. Hence, they maintain the simplicity of the finite state machine, while providing the extra power associated with a pushdown stack memory. We provide an example of a useful control specification that cannot be implemented using a finite state machine, but can be implemented using an Exception Handling Controller.

  11. Reading Machines for Blind People.

    ERIC Educational Resources Information Center

    Fender, Derek H.

    1983-01-01

    Ten stages of developing reading machines for blind people are analyzed: handling of text material; optics; electro-optics; pattern recognition; character recognition; storage; speech synthesizers; browsing and place finding; computer indexing; and other sources of input. Cost considerations of the final product are emphasized. (CL)

  12. Omnidirectional Actuator Handle

    NASA Technical Reports Server (NTRS)

    Moetteli, John B.

    1995-01-01

    Proposed actuator handle comprises two normally concentric rings, cables, and pulleys arranged such that relative displacement of rings from concentricity results in pulling of cable and consequent actuation of associated mechanism. Unlike conventional actuator handles like levers on farm implements, actuated from one or two directions only, proposed handle reached from almost any direction and actuated by pulling or pushing inner ring in any direction with respect to outer ring. Flanges installed on inner ring to cover gap between inner ring and housing to prevent clothing from being caught.

  13. Speed-Selector Guard For Machine Tool

    NASA Technical Reports Server (NTRS)

    Shakhshir, Roda J.; Valentine, Richard L.

    1992-01-01

    Simple guardplate prevents accidental reversal of direction of rotation or sudden change of speed of lathe, milling machine, or other machine tool. Custom-made for specific machine and control settings. Allows control lever to be placed at only one setting. Operator uses handle to slide guard to engage or disengage control lever. Protects personnel from injury and equipment from damage occurring if speed- or direction-control lever inadvertently placed in wrong position.

  14. Handling Pyrophoric Reagents

    SciTech Connect

    Alnajjar, Mikhail S.; Haynie, Todd O.

    2009-08-14

    Pyrophoric reagents are extremely hazardous. Special handling techniques are required to prevent contact with air and the resulting fire. This document provides several methods for working with pyrophoric reagents outside of an inert atmosphere.

  15. Helicopter Handling Qualities

    NASA Technical Reports Server (NTRS)

    1982-01-01

    Helicopters are used by the military and civilian communities for a variety of tasks and must be capable of operating in poor weather conditions and at night. Accompanying extended helicopter operations is a significant increase in pilot workload and a need for better handling qualities. An overview of the status and problems in the development and specification of helicopter handling-qualities criteria is presented. Topics for future research efforts by government and industry are highlighted.

  16. Radiological considerations regarding an alternate method for the placement of intermediate impact absorbers at the Canister Storage Building (CSB)

    SciTech Connect

    ELDER, R.E.

    2003-04-01

    This report documents radiological considerations arising from the proposed implementation of an alternate method for intermediate impact absorber placement at the Canister Storage Building (CSB). These considerations include revising the dose rate estimate, at deck level over an open storage tube and outlining the administrative controls necessary for this implementation. Currently, the MCO Handling Machine (MHM) is used to install the intermediate impact absorbers. The proposed alternative would utilize a mobile crane, thus freeing up the MHM to handle the movement of MCOs within the CSB.

  17. Electric machine

    SciTech Connect

    El-Refaie, Ayman Mohamed Fawzi; Reddy, Patel Bhageerath

    2012-07-17

    An interior permanent magnet electric machine is disclosed. The interior permanent magnet electric machine comprises a rotor comprising a plurality of radially placed magnets each having a proximal end and a distal end, wherein each magnet comprises a plurality of magnetic segments and at least one magnetic segment towards the distal end comprises a high resistivity magnetic material.

  18. Nonplanar machines

    SciTech Connect

    Ritson, D. )

    1989-05-01

    This talk examines methods available to minimize, but never entirely eliminate, degradation of machine performance caused by terrain following. Breaking of planar machine symmetry for engineering convenience and/or monetary savings must be balanced against small performance degradation, and can only be decided on a case-by-case basis. 5 refs.

  19. SLUG HANDLING DEVICES

    DOEpatents

    Gentry, J.R.

    1958-09-16

    A device is described for handling fuel elements of a neutronic reactor. The device consists of two concentric telescoped contalners that may fit about the fuel element. A number of ratchet members, equally spaced about the entrance to the containers, are pivoted on the inner container and spring biased to the outer container so thnt they are forced to hear against and hold the fuel element, the weight of which tends to force the ratchets tighter against the fuel element. The ratchets are released from their hold by raising the inner container relative to the outer memeber. This device reduces the radiation hazard to the personnel handling the fuel elements.

  20. Safe Handling Practices

    NASA Technical Reports Server (NTRS)

    1980-01-01

    In 1977 Compugraphic Corporation was experiencing an unacceptable failure rate on microelectronic chips. Company engineers suspected that static electricity was causing the trouble because some electronic components are highly susceptible to damage by electrostatic charge. From a NASA Tech Brief, they learned that Rockwell International had prepared a report on safe handling practices for electronic components. NASA provided a Technical Support Package detailing 50 safe handling procedures affecting workers, work areas, equipment and packaging materials. Where poor practices were discovered, re-education of employees and other corrective measures were undertaken.

  1. Permutation Machines.

    PubMed

    Bhatia, Swapnil; LaBoda, Craig; Yanez, Vanessa; Haddock-Angelli, Traci; Densmore, Douglas

    2016-08-19

    We define a new inversion-based machine called a permuton of n genetic elements, which allows the n elements to be rearranged in any of the n·(n - 1)·(n - 2)···2 = n! distinct orderings. We present two design algorithms for architecting such a machine. We define a notion of a feasible design and use the framework to discuss the feasibility of the permuton architectures. We have implemented our design algorithms in a freely usable web-accessible software for exploration of these machines. Permutation machines could be used as memory elements or state machines and explicitly illustrate a rational approach to designing biological systems.

  2. Permutation Machines.

    PubMed

    Bhatia, Swapnil; LaBoda, Craig; Yanez, Vanessa; Haddock-Angelli, Traci; Densmore, Douglas

    2016-08-19

    We define a new inversion-based machine called a permuton of n genetic elements, which allows the n elements to be rearranged in any of the n·(n - 1)·(n - 2)···2 = n! distinct orderings. We present two design algorithms for architecting such a machine. We define a notion of a feasible design and use the framework to discuss the feasibility of the permuton architectures. We have implemented our design algorithms in a freely usable web-accessible software for exploration of these machines. Permutation machines could be used as memory elements or state machines and explicitly illustrate a rational approach to designing biological systems. PMID:27383067

  3. Haz-Safe material handling in hazmat buildings

    SciTech Connect

    Romig, F.W.

    1994-12-31

    Material handling techniques have begun to be utilized in hazmat buildings for maneuvering and stacking of hazardous material containers. Therefore, the efficiencies involved in increased safety and productivity are being realized. In addition, there are savings in HazMat building costs and floor space or real estate inside or outside manufacturing plants. Stacking of containers is being used as structures are beefed up to install crane/hoists or air power mast type stacking machines. The purpose of this paper is to encourage potential HazMat building users and the material handling industry to look for opportunities to project material handling technology into hazmat buildings.

  4. Grain Grading and Handling.

    ERIC Educational Resources Information Center

    Rendleman, Matt; Legacy, James

    This publication provides an introduction to grain grading and handling for adult students in vocational and technical education programs. Organized in five chapters, the booklet provides a brief overview of the jobs performed at a grain elevator and of the techniques used to grade grain. The first chapter introduces the grain industry and…

  5. Cellular Manufacturing System with Dynamic Lot Size Material Handling

    NASA Astrophysics Data System (ADS)

    Khannan, M. S. A.; Maruf, A.; Wangsaputra, R.; Sutrisno, S.; Wibawa, T.

    2016-02-01

    Material Handling take as important role in Cellular Manufacturing System (CMS) design. In several study at CMS design material handling was assumed per pieces or with constant lot size. In real industrial practice, lot size may change during rolling period to cope with demand changes. This study develops CMS Model with Dynamic Lot Size Material Handling. Integer Linear Programming is used to solve the problem. Objective function of this model is minimizing total expected cost consisting machinery depreciation cost, operating costs, inter-cell material handling cost, intra-cell material handling cost, machine relocation costs, setup costs, and production planning cost. This model determines optimum cell formation and optimum lot size. Numerical examples are elaborated in the paper to ilustrate the characterictic of the model.

  6. Handling difficult materials: Household appliances

    SciTech Connect

    Woods, R.

    1994-05-01

    At last count in 1990, the US EPA reported that 2.8 million tons of household appliances (often called ''white goods'') were discarded -- about 2% of the municipal solid waste (MSW) stream. These figures may not seem particularly epic, but, considering the potentially harmful coolants, lubricants, and insulating materials left behind in these machines, the amount may be cause for concern. Management of these items is, of course, not impossible, just difficult. As more and more landfills turn white goods away, recycling is becoming the hot'' option. According to a study by the Steel Recycling Institute, about 4 million of the 8 million units discarded in the US were recycled in 1992. Recycling figures like these are impressive for any secondary material, demonstrating the strides appliance recycling has made in recent years. Implemented in May 1993, EPA's final rule on household appliance handling mandates that 80%--90% of all CFC or HCFC coolants must be recovered with certified equipment by a certified technician, who must record how the refrigerant is removed and where it is sent for recovery.

  7. Interaction with Machine Improvisation

    NASA Astrophysics Data System (ADS)

    Assayag, Gerard; Bloch, George; Cont, Arshia; Dubnov, Shlomo

    We describe two multi-agent architectures for an improvisation oriented musician-machine interaction systems that learn in real time from human performers. The improvisation kernel is based on sequence modeling and statistical learning. We present two frameworks of interaction with this kernel. In the first, the stylistic interaction is guided by a human operator in front of an interactive computer environment. In the second framework, the stylistic interaction is delegated to machine intelligence and therefore, knowledge propagation and decision are taken care of by the computer alone. The first framework involves a hybrid architecture using two popular composition/performance environments, Max and OpenMusic, that are put to work and communicate together, each one handling the process at a different time/memory scale. The second framework shares the same representational schemes with the first but uses an Active Learning architecture based on collaborative, competitive and memory-based learning to handle stylistic interactions. Both systems are capable of processing real-time audio/video as well as MIDI. After discussing the general cognitive background of improvisation practices, the statistical modelling tools and the concurrent agent architecture are presented. Then, an Active Learning scheme is described and considered in terms of using different improvisation regimes for improvisation planning. Finally, we provide more details about the different system implementations and describe several performances with the system.

  8. Monel Machining

    NASA Technical Reports Server (NTRS)

    1983-01-01

    Castle Industries, Inc. is a small machine shop manufacturing replacement plumbing repair parts, such as faucet, tub and ballcock seats. Therese Castley, president of Castle decided to introduce Monel because it offered a chance to improve competitiveness and expand the product line. Before expanding, Castley sought NERAC assistance on Monel technology. NERAC (New England Research Application Center) provided an information package which proved very helpful. The NASA database was included in NERAC's search and yielded a wealth of information on machining Monel.

  9. A PARENTAL HANDLING QUESTIONNAIRE

    PubMed Central

    Malhotra, Savita

    1990-01-01

    SUMMMARY Parental Care and Control, which are two major parental handling, variables are significantly related to psychological morbidity in children where high care-low control is associated with healthy development and low care-high control is related to psychiatric disorder. Parents by & large do not differ in their patterns of handling with regard to age and sex of the child, rural-urban living and SES except that younger children are given more care and those from high SES exercise less control among normal children. However, low care for younger children, high control for older children; low care and high control for males, rural background and higher SES families was associated with psychiatric morbidity in children. PMID:21927469

  10. Plutonium Immobilization Puck Handling

    SciTech Connect

    Kriikku, E.

    1999-01-26

    The Plutonium Immobilization Project (PIP) will immobilize excess plutonium and store the plutonium in a high level waste radiation field. To accomplish these goals, the PIP will process various forms of plutonium into plutonium oxide, mix the oxide powder with ceramic precursors, press the mixture into pucks, sinter the pucks into a ceramic puck, load the pucks into metal cans, seal the cans, load the cans into magazines, and load the magazines into a Defense Waste Processing Facility (DPWF) canister. These canisters will be sent to the DWPF, an existing Savannah River Site (SRS) facility, where molten high level waste glass will be poured into the canisters encapsulating the ceramic pucks. Due to the plutonium radiation, remote equipment will perform these operations in a contained environment. The Plutonium Immobilization Project is in the early design stages and the facility will begin operation in 2005. This paper will discuss the Plutonium Immobilization puck handling conceptual design and the puck handling equipment testing.

  11. Puck Handling Glovebox

    SciTech Connect

    Fiscus, J.B.

    2001-01-03

    The Plutonium Immobilization Project (PIP) is a joint venture between the Savannah River Site (SRS) and Lawrence Livermore National Laboratory (LLNL). This project will disposition excess weapons grade plutonium in a solid ceramic form. The plutonium, in oxide powder form, will be mixed with uranium oxide powder, ceramic precursors and binders. The combined powder mixture will be milled and possibly granulated; this processed powder will then be dispensed to a (dual action) cold press where it will be formed into green (unsintered) compacts. The compact will have the shape of a puck measuring approximately 3 1/2'' in diameter and 1 3/8'' thick. The green puck, once ejected from the press die, will be picked up by a robot and transferred into the Puck Handling Glovebox. Here the green puck will be inspected and then palletized onto furnace trays. The loaded furnace trays will be stacked/assembled and transported to the furnace where sintering operations will be performed. Finally the sintered pucks will be off loaded, inspected and transferred onto Transfer Trays which will carry the pucks from the Puck Handling Glovebox downstream to subsequent Bagless Transfer Can (BTC) operations. Due to contamination potential and high radiation rates, all Puck Handling Glovebox operations will be performed remotely using robots and specialized automation.

  12. Uranium hexafluoride handling. Proceedings

    SciTech Connect

    Not Available

    1991-12-31

    The United States Department of Energy, Oak Ridge Field Office, and Martin Marietta Energy Systems, Inc., are co-sponsoring this Second International Conference on Uranium Hexafluoride Handling. The conference is offered as a forum for the exchange of information and concepts regarding the technical and regulatory issues and the safety aspects which relate to the handling of uranium hexafluoride. Through the papers presented here, we attempt not only to share technological advances and lessons learned, but also to demonstrate that we are concerned about the health and safety of our workers and the public, and are good stewards of the environment in which we all work and live. These proceedings are a compilation of the work of many experts in that phase of world-wide industry which comprises the nuclear fuel cycle. Their experience spans the entire range over which uranium hexafluoride is involved in the fuel cycle, from the production of UF{sub 6} from the naturally-occurring oxide to its re-conversion to oxide for reactor fuels. The papers furnish insights into the chemical, physical, and nuclear properties of uranium hexafluoride as they influence its transport, storage, and the design and operation of plant-scale facilities for production, processing, and conversion to oxide. The papers demonstrate, in an industry often cited for its excellent safety record, continuing efforts to further improve safety in all areas of handling uranium hexafluoride. Selected papers were processed separately for inclusion in the Energy Science and Technology Database.

  13. Control rod system useable for fuel handling in a gas-cooled nuclear reactor

    DOEpatents

    Spurrier, Francis R.

    1976-11-30

    A control rod and its associated drive are used to elevate a complete stack of fuel blocks to a position above the core of a gas-cooled nuclear reactor. A fuel-handling machine grasps the control rod and the drive is unlatched from the rod. The stack and rod are transferred out of the reactor, or to a new location in the reactor, by the fuel-handling machine.

  14. Aircraft handling qualities data

    NASA Technical Reports Server (NTRS)

    Heffley, R. K.; Jewell, W. F.

    1972-01-01

    Available information on weight and inertia, aerodynamic derivatives, control characteristics, and stability augmentation systems is documented for 10 representative contemporary airplanes. Data sources are given for each airplane. Flight envelopes are presented and dimensional derivatives, transfer functions for control inputs, and several selected handling qualities parameters have been computed and are tabulated for 10 different flight conditions including the power approach configuration. The airplanes documented are the NT-33A, F-104A, F-4C, X-15, HL-10, Jetstar, CV-880M, B-747, C-5A, and XB-70A.

  15. Solid handling valve

    DOEpatents

    Williams, William R.

    1979-01-01

    The present invention is directed to a solids handling valve for use in combination with lock hoppers utilized for conveying pulverized coal to a coal gasifier. The valve comprises a fluid-actuated flow control piston disposed within a housing and provided with a tapered primary seal having a recessed seat on the housing and a radially expandable fluid-actuated secondary seal. The valve seals are highly resistive to corrosion, erosion and abrasion by the solids, liquids, and gases associated with the gasification process so as to minimize valve failure.

  16. Workout Machine

    NASA Technical Reports Server (NTRS)

    1995-01-01

    The Orbotron is a tri-axle exercise machine patterned after a NASA training simulator for astronaut orientation in the microgravity of space. It has three orbiting rings corresponding to roll, pitch and yaw. The user is in the middle of the inner ring with the stomach remaining in the center of all axes, eliminating dizziness. Human power starts the rings spinning, unlike the NASA air-powered system. Marketed by Fantasy Factory (formerly Orbotron, Inc.), the machine can improve aerobic capacity, strength and endurance in five to seven minute workouts.

  17. Students' Strategies for Exception Handling

    ERIC Educational Resources Information Center

    Rashkovits, Rami; Lavy, Ilana

    2011-01-01

    This study discusses and presents various strategies employed by novice programmers concerning exception handling. The main contributions of this paper are as follows: we provide an analysis tool to measure the level of assimilation of exception handling mechanism; we present and analyse strategies to handle exceptions; we present and analyse…

  18. Sectional device handling tool

    DOEpatents

    Candee, Clark B.

    1988-07-12

    Apparatus for remotely handling a device in an irradiated underwater environment includes a plurality of tubular sections interconnected end-to-end to form a handling structure, the bottom section being adapted for connection to the device. A support section is connected to the top tubular section and is adapted to be suspended from an overhead crane. Each section is flanged at its opposite ends. Axially retractable bolts in each bottom flange are threadedly engageable with holes in the top flange of an adjacent section, each bolt being biased to its retracted position and retained in place on the bottom flange. Guide pins on each top flange cooperate with mating holes on adjacent bottom flanges to guide movement of the parts to the proper interconnection orientation. Each section carries two hydraulic line segments provided with quick-connect/disconnect fittings at their opposite ends for connection to the segments of adjacent tubular sections upon interconnection thereof to form control lines which are connectable to the device and to an associated control console.

  19. Improving Memory Error Handling Using Linux

    SciTech Connect

    Carlton, Michael Andrew; Blanchard, Sean P.; Debardeleben, Nathan A.

    2014-07-25

    As supercomputers continue to get faster and more powerful in the future, they will also have more nodes. If nothing is done, then the amount of memory in supercomputer clusters will soon grow large enough that memory failures will be unmanageable to deal with by manually replacing memory DIMMs. "Improving Memory Error Handling Using Linux" is a process oriented method to solve this problem by using the Linux kernel to disable (offline) faulty memory pages containing bad addresses, preventing them from being used again by a process. The process of offlining memory pages simplifies error handling and results in reducing both hardware and manpower costs required to run Los Alamos National Laboratory (LANL) clusters. This process will be necessary for the future of supercomputing to allow the development of exascale computers. It will not be feasible without memory error handling to manually replace the number of DIMMs that will fail daily on a machine consisting of 32-128 petabytes of memory. Testing reveals the process of offlining memory pages works and is relatively simple to use. As more and more testing is conducted, the entire process will be automated within the high-performance computing (HPC) monitoring software, Zenoss, at LANL.

  20. Wacky Machines

    ERIC Educational Resources Information Center

    Fendrich, Jean

    2002-01-01

    Collectors everywhere know that local antique shops and flea markets are treasure troves just waiting to be plundered. Science teachers might take a hint from these hobbyists, for the next community yard sale might be a repository of old, quirky items that are just the things to get students thinking about simple machines. By introducing some…

  1. Bulk material handling system

    DOEpatents

    Kleysteuber, William K.; Mayercheck, William D.

    1979-01-01

    This disclosure relates to a bulk material handling system particularly adapted for underground mining and includes a monorail supported overhead and carrying a plurality of conveyors each having input and output end portions with the output end portion of a first of the conveyors positioned above an input end portion of a second of the conveyors, a device for imparting motion to the conveyors to move the material from the input end portions toward the output end portions thereof, a device for supporting at least one of the input and output end portions of the first and second conveyors from the monorail, and the supporting device including a plurality of trolleys rollingly supported by the monorail whereby the conveyors can be readily moved therealong.

  2. Operating System For Numerically Controlled Milling Machine

    NASA Technical Reports Server (NTRS)

    Ray, R. B.

    1992-01-01

    OPMILL program is operating system for Kearney and Trecker milling machine providing fast easy way to program manufacture of machine parts with IBM-compatible personal computer. Gives machinist "equation plotter" feature, which plots equations that define movements and converts equations to milling-machine-controlling program moving cutter along defined path. System includes tool-manager software handling up to 25 tools and automatically adjusts to account for each tool. Developed on IBM PS/2 computer running DOS 3.3 with 1 MB of random-access memory.

  3. Machine Learning

    NASA Astrophysics Data System (ADS)

    Hoffmann, Achim; Mahidadia, Ashesh

    The purpose of this chapter is to present fundamental ideas and techniques of machine learning suitable for the field of this book, i.e., for automated scientific discovery. The chapter focuses on those symbolic machine learning methods, which produce results that are suitable to be interpreted and understood by humans. This is particularly important in the context of automated scientific discovery as the scientific theories to be produced by machines are usually meant to be interpreted by humans. This chapter contains some of the most influential ideas and concepts in machine learning research to give the reader a basic insight into the field. After the introduction in Sect. 1, general ideas of how learning problems can be framed are given in Sect. 2. The section provides useful perspectives to better understand what learning algorithms actually do. Section 3 presents the Version space model which is an early learning algorithm as well as a conceptual framework, that provides important insight into the general mechanisms behind most learning algorithms. In section 4, a family of learning algorithms, the AQ family for learning classification rules is presented. The AQ family belongs to the early approaches in machine learning. The next, Sect. 5 presents the basic principles of decision tree learners. Decision tree learners belong to the most influential class of inductive learning algorithms today. Finally, a more recent group of learning systems are presented in Sect. 6, which learn relational concepts within the framework of logic programming. This is a particularly interesting group of learning systems since the framework allows also to incorporate background knowledge which may assist in generalisation. Section 7 discusses Association Rules - a technique that comes from the related field of Data mining. Section 8 presents the basic idea of the Naive Bayesian Classifier. While this is a very popular learning technique, the learning result is not well suited for

  4. Charging machine

    DOEpatents

    Medlin, John B.

    1976-05-25

    A charging machine for loading fuel slugs into the process tubes of a nuclear reactor includes a tubular housing connected to the process tube, a charging trough connected to the other end of the tubular housing, a device for loading the charging trough with a group of fuel slugs, means for equalizing the coolant pressure in the charging trough with the pressure in the process tubes, means for pushing the group of fuel slugs into the process tube and a latch and a seal engaging the last object in the group of fuel slugs to prevent the fuel slugs from being ejected from the process tube when the pusher is removed and to prevent pressure liquid from entering the charging machine.

  5. Fullerene Machines

    NASA Technical Reports Server (NTRS)

    Globus, Al; Saini, Subhash

    1998-01-01

    Recent computational efforts at NASA Ames Research Center and computation and experiment elsewhere suggest that a nanotechnology of machine phase functionalized fullerenes may be synthetically accessible and of great interest. We have computationally demonstrated that molecular gears fashioned from (14,0) single-walled carbon nanotubes and benzyne teeth should operate well at 50-100 gigahertz. Preliminary results suggest that these gears can be cooled by a helium atmosphere and a laser motor can power fullerene gears if a positive and negative charge have been added to form a dipole. In addition, we have unproven concepts based on experimental and computational evidence for support structures, computer control, a system architecture, a variety of components, and manufacture. Combining fullerene machines with the remarkable mechanical properties of carbon nanotubes, there is some reason to believe that a focused effort to develop fullerene nanotechnology could yield materials with tremendous properties.

  6. Induction machine

    DOEpatents

    Owen, Whitney H.

    1980-01-01

    A polyphase rotary induction machine for use as a motor or generator utilizing a single rotor assembly having two series connected sets of rotor windings, a first stator winding disposed around the first rotor winding and means for controlling the current induced in one set of the rotor windings compared to the current induced in the other set of the rotor windings. The rotor windings may be wound rotor windings or squirrel cage windings.

  7. Unvented Drum Handling Plan

    SciTech Connect

    MCDONALD, K.M.

    2000-08-01

    This drum-handling plan proposes a method to deal with unvented transuranic drums encountered during retrieval of drums. Finding unvented drums during retrieval activities was expected, as identified in the Transuranic (TRU) Phase I Retrieval Plan (HNF-4781). However, significant numbers of unvented drums were not expected until excavation of buried drums began. This plan represents accelerated planning for management of unvented drums. A plan is proposed that manages unvented drums differently based on three categories. The first category of drums is any that visually appear to be pressurized. These will be vented immediately, using either the Hanford Fire Department Hazardous Materials (Haz. Mat.) team, if such are encountered before the facilities' capabilities are established, or using internal capabilities, once established. To date, no drums have been retrieved that showed signs of pressurization. The second category consists of drums that contain a minimal amount of Pu isotopes. This minimal amount is typically less than 1 gram of Pu, but may be waste-stream dependent. Drums in this category are assayed to determine if they are low-level waste (LLW). LLW drums are typically disposed of without venting. Any unvented drums that assay as TRU will be staged for a future venting campaign, using appropriate safety precautions in their handling. The third category of drums is those for which records show larger amounts of Pu isotopes (typically greater than or equal to 1 gram of Pu). These are assumed to be TRU and are not assayed at this point, but are staged for a future venting campaign. Any of these drums that do not have a visible venting device will be staged awaiting venting, and will be managed under appropriate controls, including covering the drums to protect from direct solar exposure, minimizing of container movement, and placement of a barrier to restrict vehicle access. There are a number of equipment options available to perform the venting. The

  8. Remote handling and accelerators

    NASA Astrophysics Data System (ADS)

    Wilson, M. T.

    The high-current levels of contemporary and proposed accelerator facilities induce radiation levels into components, requiring consideration be given to maintenance techniques that reduce personnel exposure. Typical components involved include beamstops, targets, collimators, windows, and instrumentation that intercepts the direct beam. Also included are beam extraction, injection, splitting, and kicking regions, as well as purposeful spill areas where beam tails are trimmed and neutral particles are deposited. Scattered beam and secondary particles activate components all along a beamline such as vacuum pipes, magnets, and shielding. Maintenance techniques vary from hands-on to TV-viewed operation using state-of-the-art servomanipulators. Bottom- or side-entry casks are used with thimble-type target and diagnostic assemblies. Long-handled tools are operated from behind shadow shields. Swinging shield doors, unstacking block, and horizontally rolling shield roofs are all used to provide access. Common to all techniques is the need to make operations simple and to provide a means of seeing and reaching the area.

  9. REMOTE HANDLING ARRANGEMENTS

    DOEpatents

    Ginns, D.W.

    1958-04-01

    A means for handling remotely a sample pellet to be irradiated in a nuclear reactor is proposed. It is comprised essentially of an inlet tube extending through the outer shield of the reactor and being inclined so that its outer end is at a higher elevation than its inner end, an outlet tube extending through the outer shield being inclined so that its inner end is at a higher elevation than its outer end, the inner ends of these two tubes being interconnected, and a straight tube extending through the outer shield and into the reactor core between the inlet and outlet tubes and passing through the juncture of said inner ends. A rod-like member is rotatably and slidely operated within the central straight tube and has a receptacle on its inner end for receiving a sample pellet from the inlet tube. The rod member is operated to pick up a sample pellet from the inlet tube, carry the sample pellet into the irradiating position within the core, and return to the receiving position where it is rotated to dump the irradiated pellet into the outlet tube by which it is conveyed by gravity to the outside of the reactor. Stop members are provided in the inlet tube, and electrical operating devices are provided to control the sequence of the operation automatically.

  10. IC handling robot

    SciTech Connect

    Law, D.O.

    1986-09-01

    Allied Corporation, Bendix Kansas City Division uses many integrated circuits (ICs) which are 100% tested by receiving inspection prior to installation into the next assemblies. Testing includes functional testing followed by a burn-in cycle then additional functional testing. Before an IC can be functionally tested, it must be inserted into a custom plastic carrier which is placed into a metal magazine that fits the functional tester. The ICs are removed from both tester magazines and carriers prior to being placed into connectors mounted on a printed wiring board for burn-in. Then they are removed from the burn-in board and re-inserted into carriers and magazines for additional functional testing. Each device is handled manually a minimum of 12 times before it is accepted. This project established a robotic workcell which automatically prepares a dual in-line packaged (DIP) integrated circuit for several types of inspection operations performed by Receiving Inspection. Specific activities required to accomplish this goal included definition of the work cell, preparation of the robot and other equipment specifications, installation planning, establishment of programming routines and logic, design of operator safeguards, and development of the work cell concept into an operational unit capable of supporting production.

  11. Energy-efficient container handling using hybrid model predictive control

    NASA Astrophysics Data System (ADS)

    Xin, Jianbin; Negenborn, Rudy R.; Lodewijks, Gabriel

    2015-11-01

    The performance of container terminals needs to be improved to adapt the growth of containers while maintaining sustainability. This paper provides a methodology for determining the trajectory of three key interacting machines for carrying out the so-called bay handling task, involving transporting containers between a vessel and the stacking area in an automated container terminal. The behaviours of the interacting machines are modelled as a collection of interconnected hybrid systems. Hybrid model predictive control (MPC) is proposed to achieve optimal performance, balancing the handling capacity and energy consumption. The underlying control problem is hereby formulated as a mixed-integer linear programming problem. Simulation studies illustrate that a higher penalty on energy consumption indeed leads to improved sustainability using less energy. Moreover, simulations illustrate how the proposed energy-efficient hybrid MPC controller performs under different types of uncertainties.

  12. Electrical machine

    DOEpatents

    De Bock, Hendrik Pieter Jacobus; Alexander, James Pellegrino; El-Refaie, Ayman Mohamed Fawzi; Gerstler, William Dwight; Shah, Manoj Ramprasad; Shen, Xiaochun

    2016-06-21

    An apparatus, such as an electrical machine, is provided. The apparatus can include a rotor defining a rotor bore and a conduit disposed in and extending axially along the rotor bore. The conduit can have an annular conduit body defining a plurality of orifices disposed axially along the conduit and extending through the conduit body. The rotor can have an inner wall that at least partially defines the rotor bore. The orifices can extend through the conduit body along respective orifice directions, and the rotor and conduit can be configured to provide a line of sight along the orifice direction from the respective orifices to the inner wall.

  13. TEMPO machine

    SciTech Connect

    Rohwein, G.J.; Lancaster, K.T.; Lawson, R.N.

    1986-06-01

    TEMPO is a transformer powered megavolt pulse generator with an output pulse of 100 ns duration. The machine was designed for burst mode operation at pulse repetition rates up to 10 Hz with minimum pulse-to-pulse voltage variations. To meet the requirement for pulse duration a nd a 20-..omega.. output impedance within reasonable size constraints, the pulse forming transmission line was designed as two parallel water-insulated, strip-type Blumleins. Stray capacitance and electric fields along the edges of the line elements were controlled by lining the tank with plastic sheet.

  14. Fluid handling equipment: A compilation

    NASA Technical Reports Server (NTRS)

    1976-01-01

    Devices and techniques used in fluid-handling and vacuum systems are described. Section 1 presents several articles on fluid lines and tubing. Section 2 describes a number of components such as valves, filters, and regulators. The last section contains descriptions of a number of innovative fluid-handling systems.

  15. Rendering for machine vision prototyping

    NASA Astrophysics Data System (ADS)

    Reiner, Jacek

    2008-09-01

    Machine Vision systems for manufacturing quality inspection are interdisciplinary solutions including lighting, optics, cameras, image processing, segmentation, feature analysis, classification as well as integration with manufacturing process. The design and optimization of the above systems, especially image acquisition setup is mainly driven by experiment. This requires deep know-how and well equipped laboratory, which does not guarantee the optimal development process and results. This paper proposes novel usage of rendering, originating from 3D computer graphics, for machine vision prototyping and optimization. The invented technique and physically-based rendering aids selection or optimization of luminaires, tolerancing of mechanical construction and object handling, robustness predetermination or surface flaw simulation. The rendering setup utilizes mesh modeling, bump and normal mapping and light distribution sharpening with IES data files. The performed light simulation experiments for metal surfaces (face surface of bearing rollers) are validated.

  16. Machine intelligence for robotics applications

    SciTech Connect

    Weisbin, C.R.; Barhen, J.; de Saussure, G.; Hamel, W.R.; Jorgensen, C.; Oblow, E.M.; Ricks, R.E.

    1985-01-01

    The purpose of this paper is to review research in machine intelligence ongoing at the Center for Engineering Systems Advanced Research (CESAR). As a result of initial experimentation with our HERMIES-I mobile robot, hardware and software upgrades were implemented which enable fully asynchronous sonar operation, improved stepper motor control for the sensory platform, and more reliable wheel drive control. The current system, designated as HERMIES-II, is discussed. Successful demonstration of dead-reckoning navigation and the development of a sensor-based exploration and discovery algorithm which can now handle typical maze problems are reported. The development of HERMIES ''brain'' as a hypercube ensemble machine with concurrent computation and associated message passing is described. Algorithms for mapping precedence-constrained task graphs onto a hypercube yield results with high efficiency and proper load balance. A framework for a hybrid uncertainty analysis theory for decision making is described.

  17. Gang scheduling a parallel machine

    SciTech Connect

    Gorda, B.C.; Brooks, E.D. III.

    1991-03-01

    Program development on parallel machines can be a nightmare of scheduling headaches. We have developed a portable time sharing mechanism to handle the problem of scheduling gangs of processors. User program and their gangs of processors are put to sleep and awakened by the gang scheduler to provide a time sharing environment. Time quantums are adjusted according to priority queues and a system of fair share accounting. The initial platform for this software is the 128 processor BBN TC2000 in use in the Massively Parallel Computing Initiative at the Lawrence Livermore National Laboratory. 2 refs., 1 fig.

  18. Mining machine

    SciTech Connect

    Becker, H.R.

    1984-12-04

    A mining machine is disclosed comprising a mobile base and a cutting head assembly at a forward end of the mobile base having a cutter drum rotatable about an output shaft disposed along the longitudinal axis of the cutter drum. A drive system for the cutting head assembly comprises at least one motor for driving at least one toothed motor pinion and a generally cylindrical combination gear having generally circular end surfaces. A bevel or face gear is formed in at least one of the end surfaces, having teeth adapted to mate with and be driven by the toothed motor pinion. The combination gear has a worm gear formed in the outside cylindrical surface, which is disposed in driving engagement with the teeth of an output gear integrally and coaxially connected to the output shaft of the cutter drum.

  19. Information Handling is the Problem

    NASA Technical Reports Server (NTRS)

    Malin, Jane T.

    2001-01-01

    This slide presentation reviews the concerns surrounding the automation of information handling. There are two types of decision support software that supports most Space Station Flight Controllers. one is very simple, and the other is very complex. A middle ground is sought. This is the reason for the Human Centered Autonomous and Assistant Systems Testbed (HCAAST) Project. The aim is to study flight controllers at work, and in the bigger picture, with particular attention to how they handle information and how coordination of multiple teams is performed. The focus of the project is on intelligent assistants to assist in handling information for the flight controllers.

  20. HAND TRUCK FOR HANDLING EQUIPMENT

    DOEpatents

    King, D.W.

    1959-02-24

    A truck is described for the handling of large and relatively heavy pieces of equipment and particularly for the handling of ion source units for use in calutrons. The truck includes a chassis and a frame pivoted to the chassis so as to be operable to swing in the manner of a boom. The frame has spaced members so arranged that the device to be handled can be suspended between or passed between these spaced members and also rotated with respect to the frame when the device is secured to the spaced members.

  1. Ergonomic material-handling device

    DOEpatents

    Barsnick, Lance E.; Zalk, David M.; Perry, Catherine M.; Biggs, Terry; Tageson, Robert E.

    2004-08-24

    A hand-held ergonomic material-handling device capable of moving heavy objects, such as large waste containers and other large objects requiring mechanical assistance. The ergonomic material-handling device can be used with neutral postures of the back, shoulders, wrists and knees, thereby reducing potential injury to the user. The device involves two key features: 1) gives the user the ability to adjust the height of the handles of the device to ergonomically fit the needs of the user's back, wrists and shoulders; and 2) has a rounded handlebar shape, as well as the size and configuration of the handles which keep the user's wrists in a neutral posture during manipulation of the device.

  2. Tritium handling in vacuum systems

    SciTech Connect

    Gill, J.T.; Coffin, D.O.

    1986-10-01

    This report provides a course in Tritium handling in vacuum systems. Topics presented are: Properties of Tritium; Tritium compatibility of materials; Tritium-compatible vacuum equipment; and Tritium waste treatment.

  3. Machine wanting.

    PubMed

    McShea, Daniel W

    2013-12-01

    Wants, preferences, and cares are physical things or events, not ideas or propositions, and therefore no chain of pure logic can conclude with a want, preference, or care. It follows that no pure-logic machine will ever want, prefer, or care. And its behavior will never be driven in the way that deliberate human behavior is driven, in other words, it will not be motivated or goal directed. Therefore, if we want to simulate human-style interactions with the world, we will need to first understand the physical structure of goal-directed systems. I argue that all such systems share a common nested structure, consisting of a smaller entity that moves within and is driven by a larger field that contains it. In such systems, the smaller contained entity is directed by the field, but also moves to some degree independently of it, allowing the entity to deviate and return, to show the plasticity and persistence that is characteristic of goal direction. If all this is right, then human want-driven behavior probably involves a behavior-generating mechanism that is contained within a neural field of some kind. In principle, for goal directedness generally, the containment can be virtual, raising the possibility that want-driven behavior could be simulated in standard computational systems. But there are also reasons to believe that goal-direction works better when containment is also physical, suggesting that a new kind of hardware may be necessary. PMID:23792091

  4. Machine wanting.

    PubMed

    McShea, Daniel W

    2013-12-01

    Wants, preferences, and cares are physical things or events, not ideas or propositions, and therefore no chain of pure logic can conclude with a want, preference, or care. It follows that no pure-logic machine will ever want, prefer, or care. And its behavior will never be driven in the way that deliberate human behavior is driven, in other words, it will not be motivated or goal directed. Therefore, if we want to simulate human-style interactions with the world, we will need to first understand the physical structure of goal-directed systems. I argue that all such systems share a common nested structure, consisting of a smaller entity that moves within and is driven by a larger field that contains it. In such systems, the smaller contained entity is directed by the field, but also moves to some degree independently of it, allowing the entity to deviate and return, to show the plasticity and persistence that is characteristic of goal direction. If all this is right, then human want-driven behavior probably involves a behavior-generating mechanism that is contained within a neural field of some kind. In principle, for goal directedness generally, the containment can be virtual, raising the possibility that want-driven behavior could be simulated in standard computational systems. But there are also reasons to believe that goal-direction works better when containment is also physical, suggesting that a new kind of hardware may be necessary.

  5. 78 FR 34565 - Irradiation in the Production, Processing, and Handling of Animal Feed and Pet Food; Electron...

    Federal Register 2010, 2011, 2012, 2013, 2014

    2013-06-10

    ..., and Handling of Animal Feed and Pet Food; Electron Beam and X-Ray Sources for Irradiation of Poultry... generated from machine sources at energy levels not to exceed 10 million electron volts (MeV); (3) X-rays... this chapter; or (4) X-rays generated from machine sources using tantalum or gold as the...

  6. Machining operations using Yamaha YK 400 robot

    NASA Astrophysics Data System (ADS)

    Pop, A.; Pop, A.; Savu, D.; Dolga, V.

    2016-08-01

    This paper addresses the topic of industrial robots built for handling processes used in cutting machining applications. The study discourses the machining of a globe calotte made of komatex using a Yamaha YK 400 SCARA robot. Are presented aspects regarding the capabilities of Yamaha YK 400 robot, the development of the robot program, analyses of the proposed system and methods of improvement. A set of experimental analyses was conducted in order to identify correlations between the robot speed variation and distance between the points that describe the trajectory of the motion.

  7. Propane gas: Handle with care

    SciTech Connect

    Fernald, D.

    1996-04-01

    Because of its chemical composition and combustion properties, this liquefied petroleum (LP) gas can be mixed with air and used as a direct replacement for natural gas with no burner or process equipment modifications. One major and growing use of propane is as a vehicle fuel. Growing industrial use of propane also has prompted the National Fire Protection Association (NFPA) to issue new codes. NFPA standard 58-95, Storing and Handling of Liquefied Petroleum Gases, stresses the need to adhere to safe work and handling practices whenever propane is involved. All employees directly handling the gas should be formally trained and certified, and recertified annually. Although the code applies only to those directly handling propane or operating propane equipment such as portable cylinder filling stations, all employees working around or with propane or other LP gases should understand the characteristics of LP gas and be aware of basic safe handling practices. The paper discusses what LP gas is, special safety concerns, the care required in refilling cylinders, and cylinder inspection.

  8. Safe handling of large animals.

    PubMed

    Grandin, T

    1999-01-01

    The major causes of accidents with cattle, horses, and other grazing animals are: panic due to fear, male dominance aggression, or the maternal aggression of a mother protecting her newborn. Danger is inherent when handling large animals. Understanding their behavior patterns improves safety, but working with animals will never be completely safe. Calm, quiet handling and non-slip flooring are beneficial. Rough handling and excessive use of electric prods increase chances of injury to both people and animals, because fearful animals may jump, kick, or rear. Training animals to voluntarily cooperate with veterinary procedures reduces stress and improves safety. Grazing animals have a herd instinct, and a lone, isolated animal can become agitated. Providing a companion animal helps keep an animal calm. PMID:10329901

  9. Agile Machining and Inspection Non-Nuclear Report (NNR) Project

    SciTech Connect

    Lazarus, Lloyd

    2009-02-19

    This report is a high level summary of the eight major projects funded by the Agile Machining and Inspection Non-Nuclear Readiness (NNR) project (FY06.0422.3.04.R1). The largest project of the group is the Rapid Response project in which the six major sub categories are summarized. This project focused on the operations of the machining departments that will comprise Special Applications Machining (SAM) in the Kansas City Responsive Infrastructure Manufacturing & Sourcing (KCRIMS) project. This project was aimed at upgrading older machine tools, developing new inspection tools, eliminating Classified Removable Electronic Media (CREM) in the handling of classified Numerical Control (NC) programs by installing the CRONOS network, and developing methods to automatically load Coordinated-Measuring Machine (CMM) inspection data into bomb books and product score cards. Finally, the project personnel leaned perations of some of the machine tool cells, and now have the model to continue this activity.

  10. Portable vacuum object handling device

    DOEpatents

    Anderson, Gordon H.

    1983-08-09

    The disclosure relates to a portable device adapted to handle objects which are not to be touched by hand. A piston and bore wall form a vacuum chamber communicating with an adaptor sealably engageable with an object to be lifted. The piston is manually moved and set to establish vacuum. A valve is manually actuatable to apply the vacuum to lift the object.

  11. Non-contact handling device

    SciTech Connect

    Reece, Mark; Knorovsky, Gerald A.; MacCallum, Danny O.

    2007-05-15

    A pressurized fluid handling nozzle has a body with a first end and a second end, a fluid conduit and a recess at the second end. The first end is configured for connection to a pressurized fluid source. The fluid conduit has an inlet at the first end and an outlet at the recess. The nozzle uses the Bernoulli effect for lifting a part.

  12. Resistor pulse-handling capability

    SciTech Connect

    Horner, L.E.

    1981-04-01

    Methods for calculating pulse-handling capabilities of various resistor types are described. The work represents a compilation of studies derived from various sources, as indicated in the bibliography. The results indicate that resistors may be subjected to short-duration pulses exceeding their rated powers without sustaining permanent damage.

  13. Expert Systems and Document Handling.

    ERIC Educational Resources Information Center

    Edmonds, Ernest

    1987-01-01

    Describes significant attributes of expert systems, contrasts them to conventional computer systems, and provides an overview of the R1 expert system used by Digital Equipment Corporation (DEC) to put together operational systems that meet customers' requirements. Document handling, particularly pictures and images in documents, is also briefly…

  14. Flight simulator for hypersonic vehicle and a study of NASP handling qualities

    NASA Technical Reports Server (NTRS)

    Ntuen, Celestine A.; Park, Eui H.; Deeb, Joseph M.; Kim, Jung H.

    1992-01-01

    The research goal of the Human-Machine Systems Engineering Group was to study the existing handling quality studies in aircraft with sonic to supersonic speeds and power in order to understand information requirements needed for a hypersonic vehicle flight simulator. This goal falls within the NASA task statements: (1) develop flight simulator for hypersonic vehicle; (2) study NASP handling qualities; and (3) study effects of flexibility on handling qualities and on control system performance. Following the above statement of work, the group has developed three research strategies. These are: (1) to study existing handling quality studies and the associated aircraft and develop flight simulation data characterization; (2) to develop a profile for flight simulation data acquisition based on objective statement no. 1 above; and (3) to develop a simulator and an embedded expert system platform which can be used in handling quality experiments for hypersonic aircraft/flight simulation training.

  15. Tomato handling practices in restaurants.

    PubMed

    Kirkland, Elizabeth; Green, Laura R; Stone, Carmily; Reimann, Dave; Nicholas, Dave; Mason, Ryan; Frick, Roberta; Coleman, Sandra; Bushnell, Lisa; Blade, Henry; Radke, Vincent; Selman, Carol

    2009-08-01

    In recent years, multiple outbreaks of Salmonella infection have been associated with fresh tomatoes. Investigations have indicated that tomato contamination likely occurred early in the farm-to-consumer chain, although tomato consumption occurred mostly in restaurants. Researchers have hypothesized that tomato handling practices in restaurants may contribute to these outbreaks. However, few empirical data exist on how restaurant workers handle tomatoes. This study was conducted to examine tomato handling practices in restaurants. Members of the Environmental Health Specialists Network (EHS-Net) observed tomato handling practices in 449 restaurants. The data indicated that handling tomatoes appropriately posed a challenge to many restaurants. Produce-only cutting boards were not used on 49% of tomato cutting observations, and gloves were not worn in 36% of tomato cutting observations. Although tomatoes were washed under running water as recommended in most (82%) of the washing observations, tomatoes were soaked in standing water, a practice not recommended by the U.S. Food and Drug Administration (FDA), in 18% of observations, and the temperature differential between the wash water and tomatoes did not meet FDA guidelines in 21% of observations. About half of all batches of cut tomatoes in holding areas were above 41 degrees F (5 degrees C), the temperature recommended by the FDA. The maximum holding time for most (73%) of the cut tomatoes held above 41 degrees F exceeded the FDA recommended holding time of 4 h for unrefrigerated tomatoes (i.e., tomatoes held above 41 degrees F). The information provided by this study can be used to inform efforts to develop interventions and thus prevent tomato-associated illness outbreaks.

  16. Concept Design of the Payload Handling Manipulator System. [space shuttle orbiters

    NASA Technical Reports Server (NTRS)

    1975-01-01

    The design, requirements, and interface definition of a remote manipulator system developed to handle orbiter payloads are presented. End effector design, control system concepts, and man-machine engineering are considered along with crew station requirements and closed circuit television system performance requirements.

  17. Portable vacuum object handling device

    DOEpatents

    Anderson, G.H.

    1983-08-09

    The disclosure relates to a portable device adapted to handle objects which are not to be touched by hand. A piston and bore wall form a vacuum chamber communicating with an adaptor sealably engageable with an object to be lifted. The piston is manually moved and set to establish vacuum. A valve is manually actuatable to apply the vacuum to lift the object. 1 fig.

  18. Tube Alinement for Machining

    NASA Technical Reports Server (NTRS)

    Garcia, J.

    1984-01-01

    Tool with stepped shoulders alines tubes for machining in preparation for welding. Alinement with machine tool axis accurate to within 5 mils (0.13mm) and completed much faster than visual setup by machinist.

  19. Stirling machine operating experience

    NASA Technical Reports Server (NTRS)

    Ross, Brad; Dudenhoefer, James E.

    1991-01-01

    Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that Stirling machines are capable of reliable and lengthy lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and were not expected to operate for any lengthy period of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered.

  20. Women, Men, and Machines.

    ERIC Educational Resources Information Center

    Form, William; McMillen, David Byron

    1983-01-01

    Data from the first national study of technological change show that proportionately more women than men operate machines, are more exposed to machines that have alienating effects, and suffer more from the negative effects of technological change. (Author/SSH)

  1. Orion Entry Handling Qualities Assessments

    NASA Technical Reports Server (NTRS)

    Bihari, B.; Tiggers, M.; Strahan, A.; Gonzalez, R.; Sullivan, K.; Stephens, J. P.; Hart, J.; Law, H., III; Bilimoria, K.; Bailey, R.

    2011-01-01

    The Orion Command Module (CM) is a capsule designed to bring crew back from the International Space Station (ISS), the moon and beyond. The atmospheric entry portion of the flight is deigned to be flown in autopilot mode for nominal situations. However, there exists the possibility for the crew to take over manual control in off-nominal situations. In these instances, the spacecraft must meet specific handling qualities criteria. To address these criteria two separate assessments of the Orion CM s entry Handling Qualities (HQ) were conducted at NASA s Johnson Space Center (JSC) using the Cooper-Harper scale (Cooper & Harper, 1969). These assessments were conducted in the summers of 2008 and 2010 using the Advanced NASA Technology Architecture for Exploration Studies (ANTARES) six degree of freedom, high fidelity Guidance, Navigation, and Control (GN&C) simulation. This paper will address the specifics of the handling qualities criteria, the vehicle configuration, the scenarios flown, the simulation background and setup, crew interfaces and displays, piloting techniques, ratings and crew comments, pre- and post-fight briefings, lessons learned and changes made to improve the overall system performance. The data collection tools, methods, data reduction and output reports will also be discussed. The objective of the 2008 entry HQ assessment was to evaluate the handling qualities of the CM during a lunar skip return. A lunar skip entry case was selected because it was considered the most demanding of all bank control scenarios. Even though skip entry is not planned to be flown manually, it was hypothesized that if a pilot could fly the harder skip entry case, then they could also fly a simpler loads managed or ballistic (constant bank rate command) entry scenario. In addition, with the evaluation set-up of multiple tasks within the entry case, handling qualities ratings collected in the evaluation could be used to assess other scenarios such as the constant bank angle

  2. Cable-Twisting Machine

    NASA Technical Reports Server (NTRS)

    Kurnett, S.

    1982-01-01

    New cable-twisting machine is smaller and faster than many production units. Is useful mainly in production of short-run special cables. Already-twisted cable can be fed along axis of machine. Faster operation than typical industrial cable-twisting machines possible by using smaller spools of wire.

  3. Your Sewing Machine.

    ERIC Educational Resources Information Center

    Peacock, Marion E.

    The programed instruction manual is designed to aid the student in learning the parts, uses, and operation of the sewing machine. Drawings of sewing machine parts are presented, and space is provided for the student's written responses. Following an introductory section identifying sewing machine parts, the manual deals with each part and its…

  4. Automatic Inspection During Machining

    NASA Technical Reports Server (NTRS)

    Ransom, Clyde L.

    1988-01-01

    In experimental manufacturing process, numerically-controlled machine tool temporarily converts into inspection machine by installing electronic touch probes and specially-developed numerical-control software. Software drives probes in paths to and on newly machined parts and collects data on dimensions of parts.

  5. Apprentice Machine Theory Outline.

    ERIC Educational Resources Information Center

    Connecticut State Dept. of Education, Hartford. Div. of Vocational-Technical Schools.

    This volume contains outlines for 16 courses in machine theory that are designed for machine tool apprentices. Addressed in the individual course outlines are the following topics: basic concepts; lathes; milling machines; drills, saws, and shapers; heat treatment and metallurgy; grinders; quality control; hydraulics and pneumatics;…

  6. Continuous mining machine

    SciTech Connect

    Kiefer, H.E.

    1992-02-11

    This patent describes a continuous mining machine for excavating a longitudinal shaft or tunnel underneath the surface of the earth, the mining machine. It comprises: transport means for moving the machine over a floor of the shaft or tunnel that is being excavated; a working platform having forward and trailing ends.

  7. Cyclodextrin-based molecular machines.

    PubMed

    Hashidzume, Akihito; Yamaguchi, Hiroyasu; Harada, Akira

    2014-01-01

    This chapter overviews molecular machines based on cyclodextrins (CDs). The categories of CD-based molecular machines, external stimuli for CD-based molecular machines, and typical examples of CD-based molecular machines are briefly described.

  8. 7 CFR 996.4 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE MINIMUM QUALITY AND HANDLING STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by...

  9. 7 CFR 996.4 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE MINIMUM QUALITY AND HANDLING STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by...

  10. 7 CFR 985.8 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Definitions § 985.8 Handle. Handle means to prepare oil for market, acquire oil from a producer, use oil commercially of own production, or sell, transport, or ship (except as a common or contract carrier of oil owned by another), or otherwise place...

  11. 7 CFR 985.8 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Definitions § 985.8 Handle. Handle means to prepare oil for market, acquire oil from a producer, use oil commercially of own production, or sell, transport, or ship (except as a common or contract carrier of oil owned by another), or otherwise place...

  12. 7 CFR 985.8 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Definitions § 985.8 Handle. Handle means to prepare oil for market, acquire oil from a producer, use oil commercially of own production, or sell, transport, or ship (except as a common or contract carrier of oil owned by another), or otherwise place...

  13. 7 CFR 985.8 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Definitions § 985.8 Handle. Handle means to prepare oil for market, acquire oil from a producer, use oil commercially of own production, or sell, transport, or ship (except as a common or contract carrier of oil owned by another), or otherwise place...

  14. 7 CFR 985.8 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... SPEARMINT OIL PRODUCED IN THE FAR WEST Order Regulating Handling Definitions § 985.8 Handle. Handle means to prepare oil for market, acquire oil from a producer, use oil commercially of own production, or sell, transport, or ship (except as a common or contract carrier of oil owned by another), or otherwise place...

  15. Hubble Space Telescope communications and data handling

    NASA Technical Reports Server (NTRS)

    Lesko, John

    1991-01-01

    The communications and data handling system of the HST are described in detail. Consideration is given to observation scheduling, commanding, telemetry, scientific data collection, spacecraft data handling systems, and the use of the TDRSS and NASCOM data network. The science instruments control and data handling subsystem is presented in schematic form.

  16. 7 CFR 981.16 - To handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Definitions § 981.16 To handle. To handle means to use almonds commercially of own production or to sell, consign, transport, ship (except as a common carrier of almonds owned by another)...

  17. 7 CFR 981.16 - To handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Definitions § 981.16 To handle. To handle means to use almonds commercially of own production or to sell, consign, transport, ship (except as a common carrier of almonds owned by another)...

  18. 7 CFR 981.16 - To handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Definitions § 981.16 To handle. To handle means to use almonds commercially of own production or to sell, consign, transport, ship (except as a common carrier of almonds owned by another)...

  19. 7 CFR 981.16 - To handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Definitions § 981.16 To handle. To handle means to use almonds commercially of own production or to sell, consign, transport, ship (except as a common carrier of almonds owned by another)...

  20. 7 CFR 981.16 - To handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE ALMONDS GROWN IN CALIFORNIA Order Regulating Handling Definitions § 981.16 To handle. To handle means to use almonds commercially of own production or to sell, consign, transport, ship (except as a common carrier of almonds owned by another)...

  1. 7 CFR 932.16 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE OLIVES GROWN IN CALIFORNIA Order Regulating Handling Definitions § 932.16 Handle. Handle means to: (a) Size-grade olives, (b) process olives, or (c) use processed olives in the production of packaged olives, within the production area, or (d)...

  2. 7 CFR 932.16 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE OLIVES GROWN IN CALIFORNIA Order Regulating Handling Definitions § 932.16 Handle. Handle means to: (a) Size-grade olives, (b) process olives, or (c) use processed olives in the production of packaged olives, within the production area, or (d)...

  3. 7 CFR 932.16 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE OLIVES GROWN IN CALIFORNIA Order Regulating Handling Definitions § 932.16 Handle. Handle means to: (a) Size-grade olives, (b) process olives, or (c) use processed olives in the production of packaged olives, within the production area, or (d)...

  4. 7 CFR 58.443 - Whey handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Whey handling. 58.443 Section 58.443 Agriculture... Procedures § 58.443 Whey handling. (a) Adequate sanitary facilities shall be provided for the handling of whey. If outside, necessary precautions shall be taken to minimize flies, insects and development...

  5. 7 CFR 58.443 - Whey handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Whey handling. 58.443 Section 58.443 Agriculture... Procedures § 58.443 Whey handling. (a) Adequate sanitary facilities shall be provided for the handling of whey. If outside, necessary precautions shall be taken to minimize flies, insects and development...

  6. 21 CFR 820.140 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Handling, Storage, Distribution, and Installation § 820.140 Handling....

  7. 21 CFR 820.140 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Handling, Storage, Distribution, and Installation § 820.140 Handling....

  8. 21 CFR 820.140 - Handling.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Handling, Storage, Distribution, and Installation § 820.140 Handling....

  9. 21 CFR 820.140 - Handling.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Handling, Storage, Distribution, and Installation § 820.140 Handling....

  10. 21 CFR 820.140 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES QUALITY SYSTEM REGULATION Handling, Storage, Distribution, and Installation § 820.140 Handling....

  11. Smart structures technologies for parallel kinematics in handling and assembly

    NASA Astrophysics Data System (ADS)

    Keimer, Ralf; Algermissen, Stephan; Pavlovic, Nenad; Budde, Christoph

    2007-04-01

    Parallel kinematics offer a high potential for increasing performance of machines for handling and assembly. Due to greater stiffness and reduced moving masses compared to typical serial kinematics, higher accelerations and thus lower cycle times can be achieved, which is an essential benchmark for high performance in handling and assembly. However, there are some challenges left to be able to fully exploit the potential of such machines. Some of these challenges are inherent to parallel kinematics, like a low ratio between work and installation space or a considerably changing structural elasticity as a function of the position in work space. Other difficulties arise from high accelerations, which lead to high dynamic loads inducing significant vibrations. While it is essential to cope with the challenges of parallel kinematics in the design-process, smart structures technologies lend themselves as means to face some of these challenges. In this paper a 4-degree of freedom parallel mechanism based on a triglide structure is presented. This machine was designed in a way to overcome the problem of low ratio between work and installation space, by allowing for a change of the structure's configuration with the purpose of increasing the work space. Furthermore, an active vibration suppression was designed and incorporated using rods with embedded piezoceramic actuators. The design of these smart structural parts is discussed and experimental results regarding the vibration suppression are shown. Adaptive joints are another smart structures technology, which can be used to increase the performance of parallel kinematics. The adaptiveness of such joints is reflected in their ability to change their friction attributes, whereas they can be used on one hand to suppress vibrations and on the other hand to change the degrees of freedom (DOF). The vibration suppression is achieved by increasing structural damping at the end of a trajectory and by maintaining low friction

  12. Differences in Muscle Activity During Cable Resistance Training Are Influenced by Variations in Handle Types.

    PubMed

    Rendos, Nicole K; Heredia Vargas, Héctor M; Alipio, Taislaine C; Regis, Rebeca C; Romero, Matthew A; Signorile, Joseph F

    2016-07-01

    Rendos, NK, Heredia Vargas, HM, Alipio, TC, Regis, RC, Romero, MA, and Signorile, JF. Differences in muscle activity during cable resistance training are influenced by variations in handle types. J Strength Cond Res 30(7): 2001-2009, 2016-There has been a recent resurgence in the use of cable machines for resistance training allowing movements that more effectively simulate daily activities and sports-specific movements. By necessity, these devices require a machine/human interface through some type of handle. Considerable data from material handling, industrial engineering, and exercise training studies indicate that handle qualities, especially size and shape, can significantly influence force production and muscular activity, particularly of the forearm muscles, which affect the critical link in activities that require object manipulation. The purpose for this study was to examine the influence of three different handle conditions: standard handle (StandH), ball handle with the cable between the index and middle fingers (BallIM), and ball handle with the cable between the middle and ring fingers (BallMR), on activity levels (rmsEMG) of the triceps brachii lateral and long heads (TriHLat, TriHLong), brachioradialis (BR), flexor carpi radialis (FCR), extensor carpi ulnaris, and extensor digitorum (ED) during eight repetitions of standing triceps pushdown performed from 90° to 0° elbow flexion at 1.5 s per contractile stage. Handle order was randomized. No significant differences were seen for triceps or BR rmsEMG across handle conditions; however, relative patterns of activation did vary for the forearm muscles by handle condition, with more coordinated activation levels for the FCR and ED during the ball handle conditions. In addition, the rmsEMG for the ED was significantly higher during the BallIM than any other condition and during the BallMR than the StandH. These results indicate that the use of ball handles with the cable passing between different fingers

  13. Transfer Area Mechanical Handling Calculation

    SciTech Connect

    B. Dianda

    2004-06-23

    This calculation is intended to support the License Application (LA) submittal of December 2004, in accordance with the directive given by DOE correspondence received on the 27th of January 2004 entitled: ''Authorization for Bechtel SAX Company L.L. C. to Include a Bare Fuel Handling Facility and Increased Aging Capacity in the License Application, Contract Number DE-AC28-01R W12101'' (Arthur, W.J., I11 2004). This correspondence was appended by further Correspondence received on the 19th of February 2004 entitled: ''Technical Direction to Bechtel SAIC Company L.L. C. for Surface Facility Improvements, Contract Number DE-AC28-OIRW12101; TDL No. 04-024'' (BSC 2004a). These documents give the authorization for a Fuel Handling Facility to be included in the baseline. The purpose of this calculation is to establish preliminary bounding equipment envelopes and weights for the Fuel Handling Facility (FHF) transfer areas equipment. This calculation provides preliminary information only to support development of facility layouts and preliminary load calculations. The limitations of this preliminary calculation lie within the assumptions of section 5 , as this calculation is part of an evolutionary design process. It is intended that this calculation is superseded as the design advances to reflect information necessary to support License Application. The design choices outlined within this calculation represent a demonstration of feasibility and may or may not be included in the completed design. This calculation provides preliminary weight, dimensional envelope, and equipment position in building for the purposes of defining interface variables. This calculation identifies and sizes major equipment and assemblies that dictate overall equipment dimensions and facility interfaces. Sizing of components is based on the selection of commercially available products, where applicable. This is not a specific recommendation for the future use of these components or their related

  14. Machine tool locator

    DOEpatents

    Hanlon, John A.; Gill, Timothy J.

    2001-01-01

    Machine tools can be accurately measured and positioned on manufacturing machines within very small tolerances by use of an autocollimator on a 3-axis mount on a manufacturing machine and positioned so as to focus on a reference tooling ball or a machine tool, a digital camera connected to the viewing end of the autocollimator, and a marker and measure generator for receiving digital images from the camera, then displaying or measuring distances between the projection reticle and the reference reticle on the monitoring screen, and relating the distances to the actual position of the autocollimator relative to the reference tooling ball. The images and measurements are used to set the position of the machine tool and to measure the size and shape of the machine tool tip, and examine cutting edge wear. patent

  15. Fault Tolerant State Machines

    NASA Technical Reports Server (NTRS)

    Burke, Gary R.; Taft, Stephanie

    2004-01-01

    State machines are commonly used to control sequential logic in FPGAs and ASKS. An errant state machine can cause considerable damage to the device it is controlling. For example in space applications, the FPGA might be controlling Pyros, which when fired at the wrong time will cause a mission failure. Even a well designed state machine can be subject to random errors us a result of SEUs from the radiation environment in space. There are various ways to encode the states of a state machine, and the type of encoding makes a large difference in the susceptibility of the state machine to radiation. In this paper we compare 4 methods of state machine encoding and find which method gives the best fault tolerance, as well as determining the resources needed for each method.

  16. Ultra precision machining

    NASA Astrophysics Data System (ADS)

    Debra, Daniel B.; Hesselink, Lambertus; Binford, Thomas

    1990-05-01

    There are a number of fields that require or can use to advantage very high precision in machining. For example, further development of high energy lasers and x ray astronomy depend critically on the manufacture of light weight reflecting metal optical components. To fabricate these optical components with machine tools they will be made of metal with mirror quality surface finish. By mirror quality surface finish, it is meant that the dimensions tolerances on the order of 0.02 microns and surface roughness of 0.07. These accuracy targets fall in the category of ultra precision machining. They cannot be achieved by a simple extension of conventional machining processes and techniques. They require single crystal diamond tools, special attention to vibration isolation, special isolation of machine metrology, and on line correction of imperfection in the motion of the machine carriages on their way.

  17. CANISTER HANDLING FACILITY DESCRIPTION DOCUMENT

    SciTech Connect

    J.F. Beesley

    2005-04-21

    The purpose of this facility description document (FDD) is to establish requirements and associated bases that drive the design of the Canister Handling Facility (CHF), which will allow the design effort to proceed to license application. This FDD will be revised at strategic points as the design matures. This FDD identifies the requirements and describes the facility design, as it currently exists, with emphasis on attributes of the design provided to meet the requirements. This FDD is an engineering tool for design control; accordingly, the primary audience and users are design engineers. This FDD is part of an iterative design process. It leads the design process with regard to the flowdown of upper tier requirements onto the facility. Knowledge of these requirements is essential in performing the design process. The FDD follows the design with regard to the description of the facility. The description provided in this FDD reflects the current results of the design process.

  18. Intelligent packaging and material handling

    NASA Astrophysics Data System (ADS)

    Hall, Ernest L.; Shell, Richard; Slutzky, Gale D.

    1991-02-01

    The problem of palletizing (stacking on a pallet) randomly arriving mixed size and content parcels is an important task in most distribution warehouses. Today this task requires human interaction for a solution however recently several attempts have been made to automate the solution. The purpose of this paper is to present an overview of the problem an expert system approach and an estimate of the key subproblems which have been identified which are necessary for a solution. The concepts of space filling and emptying as encountered in warehousing are briefly described. Also brief descriptions of two generations of a robotic system for mixed parcel palletizing are presented. The results with these test systems indicate that automatic parcel handling at speeds comparable to humans is feasible however further work is required to obtain a robust solution.

  19. Integrated Payload Data Handling Demonstrator

    NASA Astrophysics Data System (ADS)

    FitzGeorge, T.; Wishart, A.; Hann, M.; Phan, N.; Carr, C. M.; Cupido, E.; Fox, P.; Oddy, T.; McGregor, A.; Marshall, A.; Waltham, N.

    2013-09-01

    An integrated Payload Data Handling System (IPDHS) is one in which multiple instruments share a central payload processor for their on-board data processing tasks. This offers a number of advantages over the conventional decentralised architecture. Savings in payload mass and power can be realised because the total processing resource is matched to the requirement, as opposed to the decentralised architecture where the processing resource is in effect the sum of all the applications. Overall development cost can be reduced using a common processor. At individual instrument level the potential benefits include a standardised application development environment, and the opportunity to run the instrument data handling application on a fully redundant and more powerful processor. This paper describes a joint programme by Astrium Ltd, SCISYS UK Limited, Imperial College London and RAL Space to implement a realistic demonstration of an I-PDHS using engineering models of flight instruments (a magnetometer and a camera) and a laboratory demonstrator of a central payload processor which is functionally representative of a flight design. The objective is to raise the Technology Readiness Level (TRL) of the centralised data processing technique by addressing the key areas of task partitioning to prevent fault propagation and the use of a common development process for the instrument applications. The project is supported by a UK Space Agency grant awarded under the National Space Technology Programme SpaceCITI scheme. The demonstration system is set up at the UK Space Agency's International Space Innovation Centre (ISIC) at Harwell and makes use of the ISIC Concurrent Design Facility (CDF).

  20. Perspex machine II: visualization

    NASA Astrophysics Data System (ADS)

    Anderson, James A. D. W.

    2005-01-01

    We review the perspex machine and improve it by reducing its halting conditions to one condition. We also introduce a data structure, called the "access column," that can accelerate a wide class of perspex programs. We show how the perspex can be visualised as a tetrahedron, artificial neuron, computer program, and as a geometrical transformation. We discuss the temporal properties of the perspex machine, dissolve the famous time travel paradox, and present a hypothetical time machine. Finally, we discuss some mental properties and show how the perspex machine solves the mind-body problem and, specifically, how it provides one physical explanation for the occurrence of paradigm shifts.

  1. Perspex machine II: visualization

    NASA Astrophysics Data System (ADS)

    Anderson, James A. D. W.

    2004-12-01

    We review the perspex machine and improve it by reducing its halting conditions to one condition. We also introduce a data structure, called the "access column," that can accelerate a wide class of perspex programs. We show how the perspex can be visualised as a tetrahedron, artificial neuron, computer program, and as a geometrical transformation. We discuss the temporal properties of the perspex machine, dissolve the famous time travel paradox, and present a hypothetical time machine. Finally, we discuss some mental properties and show how the perspex machine solves the mind-body problem and, specifically, how it provides one physical explanation for the occurrence of paradigm shifts.

  2. Parallel Kinematic Machines (PKM)

    SciTech Connect

    Henry, R.S.

    2000-03-17

    The purpose of this 3-year cooperative research project was to develop a parallel kinematic machining (PKM) capability for complex parts that normally require expensive multiple setups on conventional orthogonal machine tools. This non-conventional, non-orthogonal machining approach is based on a 6-axis positioning system commonly referred to as a hexapod. Sandia National Laboratories/New Mexico (SNL/NM) was the lead site responsible for a multitude of projects that defined the machining parameters and detailed the metrology of the hexapod. The role of the Kansas City Plant (KCP) in this project was limited to evaluating the application of this unique technology to production applications.

  3. On-Machine Acceptance

    SciTech Connect

    Arnold, K.F.

    2000-02-14

    Probing processes are used intermittently and not effectively as an on-line measurement device. This project was needed to evolve machine probing from merely a setup aid to an on-the-machine inspection system. Use of probing for on-machine inspection would significantly decrease cycle time by elimination of the need for first-piece inspection (at a remote location). Federal Manufacturing and Technologies (FM and T) had the manufacturing facility and the ability to integrate the system into production. The Contractor had a system that could optimize the machine tool to compensate for thermal growth and related error.

  4. Cask system design guidance for robotic handling

    SciTech Connect

    Griesmeyer, J.M.; Drotning, W.D.; Morimoto, A.K.; Bennett, P.C.

    1990-10-01

    Remote automated cask handling has the potential to reduce both the occupational exposure and the time required to process a nuclear waste transport cask at a handling facility. The ongoing Advanced Handling Technologies Project (AHTP) at Sandia National Laboratories is described. AHTP was initiated to explore the use of advanced robotic systems to perform cask handling operations at handling facilities for radioactive waste, and to provide guidance to cask designers regarding the impact of robotic handling on cask design. The proof-of-concept robotic systems developed in AHTP are intended to extrapolate from currently available commercial systems to the systems that will be available by the time that a repository would be open for operation. The project investigates those cask handling operations that would be performed at a nuclear waste repository facility during cask receiving and handling. The ongoing AHTP indicates that design guidance, rather than design specification, is appropriate, since the requirements for robotic handling do not place severe restrictions on cask design but rather focus on attention to detail and design for limited dexterity. The cask system design features that facilitate robotic handling operations are discussed, and results obtained from AHTP design and operation experience are summarized. The application of these design considerations is illustrated by discussion of the robot systems and their operation on cask feature mock-ups used in the AHTP project. 11 refs., 11 figs.

  5. Planting machine system for forest regeneration

    SciTech Connect

    Fridley, R.B.; Johnson, N.K.

    1985-01-01

    An experimental machine was developed to evaluate the effectiveness of components for intermittent planting of tree seedlings. Components tested included (a) a linkage to allow finite duration contact of the planking head with the ground, (b) pneumatics to convey seedlings to a front-opening, pivot-gate dibble, (c) plunger packers to move soil along the shear plane for compaction, and (d) seedlings with their roots encapsulated in a biomass medium to contain the roots in proper orientation and also provide a uniform size and shape for high-speed automatic handling. The experimental machine was demonstrated at a ground speed of 3.5 km/h at a 3 m intrarow spacing. 12 references.

  6. Gang scheduling a parallel machine. Revision 1

    SciTech Connect

    Gorda, B.C.; Brooks, E.D. III

    1991-12-01

    Program development on parallel machines can be a nightmare of scheduling headaches. We have developed a portable time sharing mechanism to handle the problem of scheduling gangs of processes. User programs and their gangs of processes are put to sleep and awakened by the gang scheduler to provide a time sharing environment. Time quantum are adjusted according to priority queues and a system of fair share accounting. The initial platform for this software is the 128 processor BBN TC2000 in use in the Massively Parallel Computing Initiative at the Lawrence Livermore National Laboratory.

  7. Diamond machine tool face lapping machine

    DOEpatents

    Yetter, H.H.

    1985-05-06

    An apparatus for shaping, sharpening and polishing diamond-tipped single-point machine tools. The isolation of a rotating grinding wheel from its driving apparatus using an air bearing and causing the tool to be shaped, polished or sharpened to be moved across the surface of the grinding wheel so that it does not remain at one radius for more than a single rotation of the grinding wheel has been found to readily result in machine tools of a quality which can only be obtained by the most tedious and costly processing procedures, and previously unattainable by simple lapping techniques.

  8. Diagnostics for machine protection of DEMO

    SciTech Connect

    Felton, R.

    2014-08-21

    DEMO aims to (i) integrate, demonstrate and validate all relevant technology necessary to convert fusion energy to electrical energy and (ii) that the machine and its operations are economically and environmentally acceptable. To maintain the efficiency and availability of the machine, there are several physics and combined physics/technology issues as well as the engineering issues. Machine Protection (also known as Protection of Investment) addresses both the risks to plant (to avoid costly repair or replacement) and the risks to normal operating time (to avoid loss of productivity and the return on investment). The plasma-related Machine Protection issues involve measurement and control of plasma stability, plasma purity, and plasma-wall interactions. Machine Protection aims to avoid hitting catastrophic limits by using early warning alarm systems, and controlled termination or avoidance, involving coordinated actions of the magnets, gas and auxiliary heating or current-drive systems. This article outlines the key processes, some of which are used in present-day tokamaks and some of which are new specifically for DEMO (e.g. First wall and divertor power handling) and reveals the need to research and develop new science and technology for Machine Protections in DEMO's high radiation and thermal fields. This work was funded by the RCUK Energy Programme under grant EP/I501045 and the European Communities under the contract of Association between EURATOM and CCFE and conducted partly under EFDA PPPT (WP13-DAS04). The views and opinions expressed herein do not necessarily reflect those of the European Commission.

  9. Diagnostics for machine protection of DEMO

    NASA Astrophysics Data System (ADS)

    Felton, R.

    2014-08-01

    DEMO aims to (i) integrate, demonstrate and validate all relevant technology necessary to convert fusion energy to electrical energy and (ii) that the machine and its operations are economically and environmentally acceptable. To maintain the efficiency and availability of the machine, there are several physics and combined physics/technology issues as well as the engineering issues. Machine Protection (also known as Protection of Investment) addresses both the risks to plant (to avoid costly repair or replacement) and the risks to normal operating time (to avoid loss of productivity and the return on investment). The plasma-related Machine Protection issues involve measurement and control of plasma stability, plasma purity, and plasma-wall interactions. Machine Protection aims to avoid hitting catastrophic limits by using early warning alarm systems, and controlled termination or avoidance, involving coordinated actions of the magnets, gas and auxiliary heating or current-drive systems. This article outlines the key processes, some of which are used in present-day tokamaks and some of which are new specifically for DEMO (e.g. First wall and divertor power handling) and reveals the need to research and develop new science and technology for Machine Protections in DEMO's high radiation and thermal fields. This work was funded by the RCUK Energy Programme under grant EP/I501045 and the European Communities under the contract of Association between EURATOM and CCFE and conducted partly under EFDA PPPT (WP13-DAS04). The views and opinions expressed herein do not necessarily reflect those of the European Commission.

  10. CARRIER/CASK HANDLING SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect

    E.F. Loros

    2000-06-23

    The Carrier/Cask Handling System receives casks on railcars and legal-weight trucks (LWTs) (transporters) that transport loaded casks and empty overpacks to the Monitored Geologic Repository (MGR) from the Carrier/Cask Transport System. Casks that come to the MGR on heavy-haul trucks (HHTs) are transferred onto railcars before being brought into the Carrier/Cask Handling System. The system is the interfacing system between the railcars and LWTs and the Assembly Transfer System (ATS) and Canister Transfer System (CTS). The Carrier/Cask Handling System removes loaded casks from the cask transporters and transfers the casks to a transfer cart for either the ATS or CTS, as appropriate, based on cask contents. The Carrier/Cask Handling System receives the returned empty casks from the ATS and CTS and mounts the casks back onto the transporters for reshipment. If necessary, the Carrier/Cask Handling System can also mount loaded casks back onto the transporters and remove empty casks from the transporters. The Carrier/Cask Handling System receives overpacks from the ATS loaded with canisters that have been cut open and emptied and mounts the overpacks back onto the transporters for disposal. If necessary, the Carrier/Cask Handling System can also mount empty overpacks back onto the transporters and remove loaded overpacks from them. The Carrier/Cask Handling System is located within the Carrier Bay of the Waste Handling Building System. The system consists of cranes, hoists, manipulators, and supporting equipment. The Carrier/Cask Handling System is designed with the tooling and fixtures necessary for handling a variety of casks. The Carrier/Cask Handling System performance and reliability are sufficient to support the shipping and emplacement schedules for the MGR. The Carrier/Cask Handling System interfaces with the Carrier/Cask Transport System, ATS, and CTS as noted above. The Carrier/Cask Handling System interfaces with the Waste Handling Building System for building

  11. A multistep continuous flow synthesis machine for the preparation of pyrazoles via a metal-free amine-redox process† †Raw spectra can be found at https://www.repository.cam.ac.uk/handle/1810/252343. ‡ ‡Electronic supplementary information (ESI) available. See DOI: 10.1039/c5re00082c Click here for additional data file. Click here for additional data file.

    PubMed Central

    Poh, Jian-Siang; Ley, Steven V.

    2016-01-01

    A versatile multistep continuous flow setup is reported for the four-step conversion of anilines into pyrazole products. The synthesis machine incorporates the use of amine-redox chemistry through diazotization and a metal-free vitamin C mediated reduction. The machine can be used for the synthesis of an array of analogues or the scale up of an individual target. PMID:27398231

  12. Manual handling injuries in health care workers.

    PubMed

    Bewick, N; Gardner, D

    2000-01-01

    Nursing aides are particularly susceptible to manual handling injuries because they have the primary responsibility for heavy lifting. The aim of this study was to determine why a specific group of nursing aides have the highest manual handling injury rate in their hospital. The study investigated the adequacy of the manual handling training program, knowledge of manual handling, mechanical aid availability, and use of mechanical aids. Results indicated that the nursing aides' manual handling knowledge was adequate but that they rarely used mechanical aids. This lack of use of aids was in part due to an over-reliance on their own strength and abilities. This may have been due to a lack of suitable mechanical aids on the wards or a lack of familiarity with the available aids. This study suggests that neither training alone nor the purchase of equipment alone is likely to resolve manual handling problems. PMID:10927667

  13. Simple Machine Junk Cars

    ERIC Educational Resources Information Center

    Herald, Christine

    2010-01-01

    During the month of May, the author's eighth-grade physical science students study the six simple machines through hands-on activities, reading assignments, videos, and notes. At the end of the month, they can easily identify the six types of simple machine: inclined plane, wheel and axle, pulley, screw, wedge, and lever. To conclude this unit,…

  14. Semantics via Machine Translation

    ERIC Educational Resources Information Center

    Culhane, P. T.

    1977-01-01

    Recent experiments in machine translation have given the semantic elements of collocation in Russian more objective criteria. Soviet linguists in search of semantic relationships have attempted to devise a semantic synthesis for construction of a basic language for machine translation. One such effort is summarized. (CHK)

  15. An asymptotical machine

    NASA Astrophysics Data System (ADS)

    Cristallini, Achille

    2016-07-01

    A new and intriguing machine may be obtained replacing the moving pulley of a gun tackle with a fixed point in the rope. Its most important feature is the asymptotic efficiency. Here we obtain a satisfactory description of this machine by means of vector calculus and elementary trigonometry. The mathematical model has been compared with experimental data and briefly discussed.

  16. Technique for Machining Glass

    NASA Technical Reports Server (NTRS)

    Rice, S. H.

    1982-01-01

    Process for machining glass with conventional carbide tools requires a small quantity of a lubricant for aluminum applied to area of glass to be machined. A carbide tool is then placed against workpiece with light pressure. Tool is raised periodically to clear work of glass dust and particles. Additional lubricant is applied as it is displaced.

  17. Compound taper milling machine

    NASA Technical Reports Server (NTRS)

    Campbell, N. R.

    1969-01-01

    Simple, inexpensive milling machine tapers panels from a common apex to a uniform height at panel edge regardless of the panel perimeter configuration. The machine consists of an adjustable angled beam upon which the milling tool moves back and forth above a rotatable table upon which the workpiece is held.

  18. Stirling machine operating experience

    SciTech Connect

    Ross, B.; Dudenhoefer, J.E.

    1994-09-01

    Numerous Stirling machines have been built and operated, but the operating experience of these machines is not well known. It is important to examine this operating experience in detail, because it largely substantiates the claim that stirling machines are capable of reliable and lengthy operating lives. The amount of data that exists is impressive, considering that many of the machines that have been built are developmental machines intended to show proof of concept, and are not expected to operate for lengthy periods of time. Some Stirling machines (typically free-piston machines) achieve long life through non-contact bearings, while other Stirling machines (typically kinematic) have achieved long operating lives through regular seal and bearing replacements. In addition to engine and system testing, life testing of critical components is also considered. The record in this paper is not complete, due to the reluctance of some organizations to release operational data and because several organizations were not contacted. The authors intend to repeat this assessment in three years, hoping for even greater participation.

  19. Machining heavy plastic sections

    NASA Technical Reports Server (NTRS)

    Stalkup, O. M.

    1967-01-01

    Machining technique produces consistently satisfactory plane-parallel optical surfaces for pressure windows, made of plexiglass, required to support a photographic study of liquid rocket combustion processes. The surfaces are machined and polished to the required tolerances and show no degradation from stress relaxation over periods as long as 6 months.

  20. THE TEACHING MACHINE.

    ERIC Educational Resources Information Center

    KLEIN, CHARLES; WAYNE, ELLIS

    THE ROLE OF THE TEACHING MACHINE IS COMPARED WITH THE ROLE OF THE PROGRAMED TEXTBOOK. THE TEACHING MACHINE IS USED FOR INDIVIDUAL INSTRUCTION, CONTAINS AND PRESENTS PROGRAM CONTENT IN STEPS, PROVIDES A MEANS WHEREBY THE STUDENT MAY RESPOND TO THE PROGRAM, PROVIDES THE STUDENT WITH IMMEDIATE INFORMATION OF SOME KIND CONCERNING HIS RESPONSE THAT CAN…

  1. Simple Machines Made Simple.

    ERIC Educational Resources Information Center

    St. Andre, Ralph E.

    Simple machines have become a lost point of study in elementary schools as teachers continue to have more material to cover. This manual provides hands-on, cooperative learning activities for grades three through eight concerning the six simple machines: wheel and axle, inclined plane, screw, pulley, wedge, and lever. Most activities can be…

  2. Machine Translation Project

    NASA Technical Reports Server (NTRS)

    Bajis, Katie

    1993-01-01

    The characteristics and capabilities of existing machine translation systems were examined and procurement recommendations were developed. Four systems, SYSTRAN, GLOBALINK, PC TRANSLATOR, and STYLUS, were determined to meet the NASA requirements for a machine translation system. Initially, four language pairs were selected for implementation. These are Russian-English, French-English, German-English, and Japanese-English.

  3. 14. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific Railroad Carlin Shops, view to north (90mm lens). - Southern Pacific Railroad, Carlin Shops, Roundhouse Machine Shop Extension, Foot of Sixth Street, Carlin, Elko County, NV

  4. BRITISH MOLDING MACHINE, PBQ AUTOMATIC COPE AND DRAG MOLDING MACHINE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BRITISH MOLDING MACHINE, PBQ AUTOMATIC COPE AND DRAG MOLDING MACHINE MAKES BOTH MOLD HALVES INDIVIDUALLY WHICH ARE LATER ROTATED, ASSEMBLED, AND LOWERED TO POURING CONVEYORS BY ASSISTING MACHINES. - Southern Ductile Casting Company, Casting, 2217 Carolina Avenue, Bessemer, Jefferson County, AL

  5. Ergonomics: safe patient handling and mobility.

    PubMed

    Hallmark, Beth; Mechan, Patricia; Shores, Lynne

    2015-03-01

    This article reviews and investigates the issues surrounding ergonomics, with a specific focus on safe patient handling and mobility. The health care worker of today faces many challenges, one of which is related to the safety of patients. Safe patient handling and mobility is on the forefront of the movement to improve patient safety. This article reviews the risks associated with patient handling and mobility, and informs the reader of current evidence-based practice relevant to this area of care. PMID:25680494

  6. ATA diagnostic data handling system: an overview

    SciTech Connect

    Chambers, F.W.; Kallman, J.; McDonald, J.; Slominski, M.

    1984-06-14

    The functions to be performed by the ATA diagnostic data handling system are discussed. The capabilities of the present data acquisition system (System 0) are presented. The goals for the next generation acquisition system (System 1), currently under design, are discussed. Facilities on the Octopus system for data handling are reviewed. Finally, we discuss what has been learned about diagnostics and computer based data handling during the past year.

  7. Introduction to machine learning.

    PubMed

    Baştanlar, Yalin; Ozuysal, Mustafa

    2014-01-01

    The machine learning field, which can be briefly defined as enabling computers make successful predictions using past experiences, has exhibited an impressive development recently with the help of the rapid increase in the storage capacity and processing power of computers. Together with many other disciplines, machine learning methods have been widely employed in bioinformatics. The difficulties and cost of biological analyses have led to the development of sophisticated machine learning approaches for this application area. In this chapter, we first review the fundamental concepts of machine learning such as feature assessment, unsupervised versus supervised learning and types of classification. Then, we point out the main issues of designing machine learning experiments and their performance evaluation. Finally, we introduce some supervised learning methods. PMID:24272434

  8. Introduction to machine learning.

    PubMed

    Baştanlar, Yalin; Ozuysal, Mustafa

    2014-01-01

    The machine learning field, which can be briefly defined as enabling computers make successful predictions using past experiences, has exhibited an impressive development recently with the help of the rapid increase in the storage capacity and processing power of computers. Together with many other disciplines, machine learning methods have been widely employed in bioinformatics. The difficulties and cost of biological analyses have led to the development of sophisticated machine learning approaches for this application area. In this chapter, we first review the fundamental concepts of machine learning such as feature assessment, unsupervised versus supervised learning and types of classification. Then, we point out the main issues of designing machine learning experiments and their performance evaluation. Finally, we introduce some supervised learning methods.

  9. Micro-machining.

    PubMed

    Brinksmeier, Ekkard; Preuss, Werner

    2012-08-28

    Manipulating bulk material at the atomic level is considered to be the domain of physics, chemistry and nanotechnology. However, precision engineering, especially micro-machining, has become a powerful tool for controlling the surface properties and sub-surface integrity of the optical, electronic and mechanical functional parts in a regime where continuum mechanics is left behind and the quantum nature of matter comes into play. The surprising subtlety of micro-machining results from the extraordinary precision of tools, machines and controls expanding into the nanometre range-a hundred times more precise than the wavelength of light. In this paper, we will outline the development of precision engineering, highlight modern achievements of ultra-precision machining and discuss the necessity of a deeper physical understanding of micro-machining.

  10. "Make My Day": Handling Conflict. ERIC Report.

    ERIC Educational Resources Information Center

    Demo, Mary Penasack

    1986-01-01

    Features documents in "Resources in Education" that describe how the following occupational groups handle conflict: nurses, school superintendents, city managers, board members, teachers, and training directors. (PD)

  11. 7 CFR 917.6 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN CALIFORNIA... for peaches, packing or causing the fruit to be packed also constitutes handling; Provided...

  12. 7 CFR 917.6 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN CALIFORNIA... for peaches, packing or causing the fruit to be packed also constitutes handling; Provided...

  13. Apparatus for remotely handling components

    DOEpatents

    Szkrybalo, Gregory A.; Griffin, Donald L.

    1994-01-01

    The inventive apparatus for remotely handling bar-like components which define a longitudinal direction includes a gripper mechanism for gripping the component including first and second gripper members longitudinally fixedly spaced from each other and oriented parallel to each other in planes transverse to the longitudinal direction. Each gripper member includes a jaw having at least one V-groove with opposing surfaces intersecting at a base and extending radially relative to the longitudinal direction for receiving the component in an open end between the opposing surfaces. The V-grooves on the jaw plate of the first and second gripper members are aligned in the longitudinal direction to support the component in the first and second gripper members. A jaw is rotatably mounted on and a part of each of the first and second gripper members for selectively assuming a retracted mode in which the open end of the V-groove is unobstructed and active mode in which the jaw spans the open end of the V-groove in the first and second gripper members. The jaw has a locking surface for contacting the component in the active mode to secure the component between the locking surface of the jaw and the opposing surfaces of the V-groove. The locking surface has a plurality of stepped portions, each defining a progressively decreasing radial distance between the base of the V-groove and the stepped portion opposing the base to accommodate varying sizes of components.

  14. 15 CFR 700.31 - Metalworking machines.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... machinery and hammers Gear cutting and finishing machines Grinding machines Hydraulic and pneumatic presses, power driven Machining centers and way-type machines Manual presses Mechanical presses, power...

  15. 15 CFR 700.31 - Metalworking machines.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... machinery and hammers Gear cutting and finishing machines Grinding machines Hydraulic and pneumatic presses, power driven Machining centers and way-type machines Manual presses Mechanical presses, power...

  16. WASTE HANDLING BUILDING ELECTRICAL SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect

    S.C. Khamamkar

    2000-06-23

    The Waste Handling Building Electrical System performs the function of receiving, distributing, transforming, monitoring, and controlling AC and DC power to all waste handling building electrical loads. The system distributes normal electrical power to support all loads that are within the Waste Handling Building (WHB). The system also generates and distributes emergency power to support designated emergency loads within the WHB within specified time limits. The system provides the capability to transfer between normal and emergency power. The system provides emergency power via independent and physically separated distribution feeds from the normal supply. The designated emergency electrical equipment will be designed to operate during and after design basis events (DBEs). The system also provides lighting, grounding, and lightning protection for the Waste Handling Building. The system is located in the Waste Handling Building System. The system consists of a diesel generator, power distribution cables, transformers, switch gear, motor controllers, power panel boards, lighting panel boards, lighting equipment, lightning protection equipment, control cabling, and grounding system. Emergency power is generated with a diesel generator located in a QL-2 structure and connected to the QL-2 bus. The Waste Handling Building Electrical System distributes and controls primary power to acceptable industry standards, and with a dependability compatible with waste handling building reliability objectives for non-safety electrical loads. It also generates and distributes emergency power to the designated emergency loads. The Waste Handling Building Electrical System receives power from the Site Electrical Power System. The primary material handling power interfaces include the Carrier/Cask Handling System, Canister Transfer System, Assembly Transfer System, Waste Package Remediation System, and Disposal Container Handling Systems. The system interfaces with the MGR Operations

  17. The basic anaesthesia machine.

    PubMed

    Gurudatt, Cl

    2013-09-01

    After WTG Morton's first public demonstration in 1846 of use of ether as an anaesthetic agent, for many years anaesthesiologists did not require a machine to deliver anaesthesia to the patients. After the introduction of oxygen and nitrous oxide in the form of compressed gases in cylinders, there was a necessity for mounting these cylinders on a metal frame. This stimulated many people to attempt to construct the anaesthesia machine. HEG Boyle in the year 1917 modified the Gwathmey's machine and this became popular as Boyle anaesthesia machine. Though a lot of changes have been made for the original Boyle machine still the basic structure remains the same. All the subsequent changes which have been brought are mainly to improve the safety of the patients. Knowing the details of the basic machine will make the trainee to understand the additional improvements. It is also important for every practicing anaesthesiologist to have a thorough knowledge of the basic anaesthesia machine for safe conduct of anaesthesia.

  18. Machine learning and radiology.

    PubMed

    Wang, Shijun; Summers, Ronald M

    2012-07-01

    In this paper, we give a short introduction to machine learning and survey its applications in radiology. We focused on six categories of applications in radiology: medical image segmentation, registration, computer aided detection and diagnosis, brain function or activity analysis and neurological disease diagnosis from fMR images, content-based image retrieval systems for CT or MRI images, and text analysis of radiology reports using natural language processing (NLP) and natural language understanding (NLU). This survey shows that machine learning plays a key role in many radiology applications. Machine learning identifies complex patterns automatically and helps radiologists make intelligent decisions on radiology data such as conventional radiographs, CT, MRI, and PET images and radiology reports. In many applications, the performance of machine learning-based automatic detection and diagnosis systems has shown to be comparable to that of a well-trained and experienced radiologist. Technology development in machine learning and radiology will benefit from each other in the long run. Key contributions and common characteristics of machine learning techniques in radiology are discussed. We also discuss the problem of translating machine learning applications to the radiology clinical setting, including advantages and potential barriers.

  19. Machine Learning and Radiology

    PubMed Central

    Wang, Shijun; Summers, Ronald M.

    2012-01-01

    In this paper, we give a short introduction to machine learning and survey its applications in radiology. We focused on six categories of applications in radiology: medical image segmentation, registration, computer aided detection and diagnosis, brain function or activity analysis and neurological disease diagnosis from fMR images, content-based image retrieval systems for CT or MRI images, and text analysis of radiology reports using natural language processing (NLP) and natural language understanding (NLU). This survey shows that machine learning plays a key role in many radiology applications. Machine learning identifies complex patterns automatically and helps radiologists make intelligent decisions on radiology data such as conventional radiographs, CT, MRI, and PET images and radiology reports. In many applications, the performance of machine learning-based automatic detection and diagnosis systems has shown to be comparable to that of a well-trained and experienced radiologist. Technology development in machine learning and radiology will benefit from each other in the long run. Key contributions and common characteristics of machine learning techniques in radiology are discussed. We also discuss the problem of translating machine learning applications to the radiology clinical setting, including advantages and potential barriers. PMID:22465077

  20. The Basic Anaesthesia Machine

    PubMed Central

    Gurudatt, CL

    2013-01-01

    After WTG Morton's first public demonstration in 1846 of use of ether as an anaesthetic agent, for many years anaesthesiologists did not require a machine to deliver anaesthesia to the patients. After the introduction of oxygen and nitrous oxide in the form of compressed gases in cylinders, there was a necessity for mounting these cylinders on a metal frame. This stimulated many people to attempt to construct the anaesthesia machine. HEG Boyle in the year 1917 modified the Gwathmey's machine and this became popular as Boyle anaesthesia machine. Though a lot of changes have been made for the original Boyle machine still the basic structure remains the same. All the subsequent changes which have been brought are mainly to improve the safety of the patients. Knowing the details of the basic machine will make the trainee to understand the additional improvements. It is also important for every practicing anaesthesiologist to have a thorough knowledge of the basic anaesthesia machine for safe conduct of anaesthesia. PMID:24249876

  1. A sensor-based automation system for handling nuclear materials

    SciTech Connect

    Drotning, W.; Kimberly, H.; Wapman, W.; Darras, D.

    1997-03-01

    An automated system is being developed for handling large payloads of radioactive nuclear materials in an analytical laboratory. The automation system performs unpacking and repacking of payloads from shipping and storage containers, and delivery of the payloads to the stations in the laboratory. The system uses machine vision and force/torque sensing to provide sensor-based control of the automation system in order to enhance system safety, flexibility, and robustness, and achieve easy remote operation. The automation system also controls the operation of the laboratory measurement systems and the coordination of them with the robotic system. Particular attention has been given to system design features and analytical methods that provide an enhanced level of operational safety. Independent mechanical gripper interlock and tool release mechanisms were designed to prevent payload mishandling. An extensive Failure Modes and Effects Analysis of the automation system was developed as a safety design analysis tool.

  2. Distributed and parallel approach for handle and perform huge datasets

    NASA Astrophysics Data System (ADS)

    Konopko, Joanna

    2015-12-01

    Big Data refers to the dynamic, large and disparate volumes of data comes from many different sources (tools, machines, sensors, mobile devices) uncorrelated with each others. It requires new, innovative and scalable technology to collect, host and analytically process the vast amount of data. Proper architecture of the system that perform huge data sets is needed. In this paper, the comparison of distributed and parallel system architecture is presented on the example of MapReduce (MR) Hadoop platform and parallel database platform (DBMS). This paper also analyzes the problem of performing and handling valuable information from petabytes of data. The both paradigms: MapReduce and parallel DBMS are described and compared. The hybrid architecture approach is also proposed and could be used to solve the analyzed problem of storing and processing Big Data.

  3. Handling Temporality of Clinical Events for Drug Safety Surveillance.

    PubMed

    Zhao, Jing; Henriksson, Aron; Kvist, Maria; Asker, Lars; Boström, Henrik

    2015-01-01

    Using longitudinal data in electronic health records (EHRs) for post-marketing adverse drug event (ADE) detection allows for monitoring patients throughout their medical history. Machine learning methods have been shown to be efficient and effective in screening health records and detecting ADEs. How best to exploit historical data, as encoded by clinical events in EHRs is, however, not very well understood. In this study, three strategies for handling temporality of clinical events are proposed and evaluated using an EHR database from Stockholm, Sweden. The random forest learning algorithm is applied to predict fourteen ADEs using clinical events collected from different lengths of patient history. The results show that, in general, including longer patient history leads to improved predictive performance, and that assigning weights to events according to time distance from the ADE yields the biggest improvement. PMID:26958278

  4. DNA-based machines.

    PubMed

    Wang, Fuan; Willner, Bilha; Willner, Itamar

    2014-01-01

    The base sequence in nucleic acids encodes substantial structural and functional information into the biopolymer. This encoded information provides the basis for the tailoring and assembly of DNA machines. A DNA machine is defined as a molecular device that exhibits the following fundamental features. (1) It performs a fuel-driven mechanical process that mimics macroscopic machines. (2) The mechanical process requires an energy input, "fuel." (3) The mechanical operation is accompanied by an energy consumption process that leads to "waste products." (4) The cyclic operation of the DNA devices, involves the use of "fuel" and "anti-fuel" ingredients. A variety of DNA-based machines are described, including the construction of "tweezers," "walkers," "robots," "cranes," "transporters," "springs," "gears," and interlocked cyclic DNA structures acting as reconfigurable catenanes, rotaxanes, and rotors. Different "fuels", such as nucleic acid strands, pH (H⁺/OH⁻), metal ions, and light, are used to trigger the mechanical functions of the DNA devices. The operation of the devices in solution and on surfaces is described, and a variety of optical, electrical, and photoelectrochemical methods to follow the operations of the DNA machines are presented. We further address the possible applications of DNA machines and the future perspectives of molecular DNA devices. These include the application of DNA machines as functional structures for the construction of logic gates and computing, for the programmed organization of metallic nanoparticle structures and the control of plasmonic properties, and for controlling chemical transformations by DNA machines. We further discuss the future applications of DNA machines for intracellular sensing, controlling intracellular metabolic pathways, and the use of the functional nanostructures for drug delivery and medical applications.

  5. DNA-based machines.

    PubMed

    Wang, Fuan; Willner, Bilha; Willner, Itamar

    2014-01-01

    The base sequence in nucleic acids encodes substantial structural and functional information into the biopolymer. This encoded information provides the basis for the tailoring and assembly of DNA machines. A DNA machine is defined as a molecular device that exhibits the following fundamental features. (1) It performs a fuel-driven mechanical process that mimics macroscopic machines. (2) The mechanical process requires an energy input, "fuel." (3) The mechanical operation is accompanied by an energy consumption process that leads to "waste products." (4) The cyclic operation of the DNA devices, involves the use of "fuel" and "anti-fuel" ingredients. A variety of DNA-based machines are described, including the construction of "tweezers," "walkers," "robots," "cranes," "transporters," "springs," "gears," and interlocked cyclic DNA structures acting as reconfigurable catenanes, rotaxanes, and rotors. Different "fuels", such as nucleic acid strands, pH (H⁺/OH⁻), metal ions, and light, are used to trigger the mechanical functions of the DNA devices. The operation of the devices in solution and on surfaces is described, and a variety of optical, electrical, and photoelectrochemical methods to follow the operations of the DNA machines are presented. We further address the possible applications of DNA machines and the future perspectives of molecular DNA devices. These include the application of DNA machines as functional structures for the construction of logic gates and computing, for the programmed organization of metallic nanoparticle structures and the control of plasmonic properties, and for controlling chemical transformations by DNA machines. We further discuss the future applications of DNA machines for intracellular sensing, controlling intracellular metabolic pathways, and the use of the functional nanostructures for drug delivery and medical applications. PMID:24647836

  6. Integration of image analysis and robotics into a fully automated colony picking and plate handling system.

    PubMed Central

    Jones, P; Watson, A; Davies, M; Stubbings, S

    1992-01-01

    We describe here the integration of image analysis and robotics to produce a fully automated colony picking/plate handling system. Biological tests were performed to verify its performance in terms of sterilisation and accuracy of picking. The machine was then used by a single operative to pick a 36,000 clone cDNA library in approximately 42 hrs over 5 days. Images PMID:1408762

  7. Quantum Boltzmann Machine

    NASA Astrophysics Data System (ADS)

    Kulchytskyy, Bohdan; Andriyash, Evgeny; Amin, Mohammed; Melko, Roger

    The field of machine learning has been revolutionized by the recent improvements in the training of deep networks. Their architecture is based on a set of stacked layers of simpler modules. One of the most successful building blocks, known as a restricted Boltzmann machine, is an energetic model based on the classical Ising Hamiltonian. In our work, we investigate the benefits of quantum effects on the learning capacity of Boltzmann machines by extending its underlying Hamiltonian with a transverse field. For this purpose, we employ exact and stochastic training procedures on data sets with physical origins.

  8. Machine Tool Software

    NASA Technical Reports Server (NTRS)

    1988-01-01

    A NASA-developed software package has played a part in technical education of students who major in Mechanical Engineering Technology at William Rainey Harper College. Professor Hack has been using (APT) Automatically Programmed Tool Software since 1969 in his CAD/CAM Computer Aided Design and Manufacturing curriculum. Professor Hack teaches the use of APT programming languages for control of metal cutting machines. Machine tool instructions are geometry definitions written in APT Language to constitute a "part program." The part program is processed by the machine tool. CAD/CAM students go from writing a program to cutting steel in the course of a semester.

  9. Wind motor machine

    SciTech Connect

    Goedecke, A.

    1984-12-25

    An improved wind motor machine having a wind rotor rotatable about a vertical axis. The rotor core body of the machine is provided with convexly curved wind application surfaces and coacting outer wing bodies having load supporting airplane wing-shaped cross-sections. The efficiency of the machine is improved by means of stream guiding bodies disposed in the intermediate space between the rotor core body and the wing bodies. These stream guiding bodies extend in a desired streaming direction, that is normal to the rotational axis of the wind body, which insures substantially laminar air streaming within the intermediate space.

  10. OPTICAM machine design

    NASA Astrophysics Data System (ADS)

    Liedes, Jyrki T.

    1992-01-01

    Rank Pneumo has worked with the Center of Optics Manufacturing to design a multiple-axis flexible machining center for spherical lens fabrication. The OPTICAM/SM prototype machine has been developed in cooperation with the Center's Manufacturing Advisory Board. The SM will generate, fine grind, pre-polish, and center a spherical lens surface in one setup sequence. Unique features of the design incorporate machine resident metrology to provide RQM (Real-time Quality Management) and closed-loop feedback control that corrects for lens thickness, diameter, and centering error. SPC (Statistical Process Control) software can compensate for process drift and QA data collection is provided without additional labor.

  11. Machine tools get smarter

    SciTech Connect

    Valenti, M.

    1995-11-01

    This article describes how, using software, sensors, and controllers, a new generation of intelligent machine tools are optimizing grinding, milling, and molding processes. A paradox of manufacturing parts is that the faster the parts are made, the less accurate they are--and vice versa. However, a combination of software, sensors, controllers, and mechanical innovations are being used to create a new generation of intelligent machine tools capable of optimizing their own grinding, milling, and molding processes. These brainy tools are allowing manufacturers to machine more-complex, higher-quality parts in shorter cycle times. The technology also lowers scrap rates and reduces or eliminates the need for polishing inadequately finished parts.

  12. 29 CFR 1917.18 - Log handling.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 7 2010-07-01 2010-07-01 false Log handling. 1917.18 Section 1917.18 Labor Regulations...) MARINE TERMINALS Marine Terminal Operations § 1917.18 Log handling. (a) The employer shall ensure that structures (bunks) used to contain logs have rounded corners and rounded structural parts to avoid...

  13. 7 CFR 983.14 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling,...

  14. 9 CFR 3.118 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of...

  15. 7 CFR 1216.12 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or...

  16. 7 CFR 1216.12 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or...

  17. 9 CFR 3.66 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Handling. 3.66 Section 3.66 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL... Transportation Standards § 3.66 Handling. (a) Any person who is subject to the Animal Welfare regulations and...

  18. 7 CFR 1219.11 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass...

  19. 7 CFR 1219.11 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass...

  20. 7 CFR 1219.11 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass...

  1. 7 CFR 1210.307 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place or cause watermelons to which one...

  2. 7 CFR 1210.307 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place or cause watermelons to which one...

  3. 7 CFR 1210.307 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place or cause watermelons to which one...

  4. 7 CFR 1210.307 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place or cause watermelons to which one...

  5. 7 CFR 1210.307 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place or cause watermelons to which one...

  6. Information Handling, Organizational Structure, and Power.

    ERIC Educational Resources Information Center

    Buckland, Michael K.

    1989-01-01

    Uses examples from military strategic communications to demonstrate that organizational structures and the distribution of power within organizational structures adapt to changes in information handling capability. It is concluded that delegation and decentralization can be viewed as indicative of inadequate information handling and that improved…

  7. 7 CFR 1221.11 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.11 Handle. Handle means to engage in the receiving or acquiring of sorghum and in the shipment (except as a common...

  8. 7 CFR 1221.11 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.11 Handle. Handle means to engage in the receiving or acquiring of sorghum and in the shipment (except as a common...

  9. 7 CFR 1221.11 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.11 Handle. Handle means to engage in the receiving or acquiring of sorghum and in the shipment (except as a common...

  10. 7 CFR 1221.11 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.11 Handle. Handle means to engage in the receiving or acquiring of sorghum and in the shipment (except as a common...

  11. 7 CFR 1221.11 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE SORGHUM PROMOTION, RESEARCH, AND INFORMATION ORDER Sorghum Promotion, Research, and Information Order Definitions § 1221.11 Handle. Handle means to engage in the receiving or acquiring of sorghum and in the shipment (except as a common...

  12. Safe patient handling for rehabilitation professionals.

    PubMed

    Waters, Thomas R; Rockefeller, Kathleen

    2010-01-01

    Every day, thousands of physical therapists and rehabilitation nurses are required to perform physically demanding therapeutic patient handling tasks that are stressful to the caregiver and increase his or her risk of developing work-related musculoskeletal disorders (MSDs). In rehabilitation, patient handling tasks might be classified as"traditional" or "therapeutic."Traditional tasks have a practical goal, such as transferring a patient from bed to a wheelchair, and therapeutic tasks have more targeted goals such as facilitating patient function and independence. Therapeutic patient handling tasks present a greater risk for caregivers to sustain work-related MSDs than typical patient handling tasks do because caregivers are exposed to high mechanical loads on the spinal tissues for longer amounts of time. The Veterans Health Administration, Association of Rehabilitation Nurses, and the American Physical Therapy Association endorse the use of modern patient handling technology as part of a comprehensive safe patient handling program for providing therapy in rehabilitation settings. Information about patient handling technology that is effective in reducing the risk of work-related MSDs from performing therapeutic patient handling and movement tasks is also presented and discussed in this article.

  13. 29 CFR 1926.953 - Material handling.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 29 Labor 8 2010-07-01 2010-07-01 false Material handling. 1926.953 Section 1926.953 Labor... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the... shall be attached to the trailing end of the longest pole. (c) Storage. (1) No materials or...

  14. 7 CFR 927.316 - Handling regulation.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Handling regulation. 927.316 Section 927.316 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing... WASHINGTON Rules and Regulations Assessment Rate § 927.316 Handling regulation. During the period August...

  15. 7 CFR 927.316 - Handling regulation.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Handling regulation. 927.316 Section 927.316 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING... WASHINGTON Rules and Regulations Assessment Rate § 927.316 Handling regulation. During the period August...

  16. 7 CFR 927.316 - Handling regulation.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Handling regulation. 927.316 Section 927.316 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING... WASHINGTON Rules and Regulations Assessment Rate § 927.316 Handling regulation. During the period August...

  17. 7 CFR 1219.11 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass...

  18. 7 CFR 996.4 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale of cleaned-inshell or shelled peanuts or other activity causing peanuts to enter into...

  19. 7 CFR 996.4 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale of cleaned-inshell or shelled peanuts or other activity causing peanuts to enter into...

  20. 7 CFR 1216.12 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or...

  1. 7 CFR 1216.12 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or...

  2. 7 CFR 1216.12 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or...

  3. 7 CFR 996.4 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale of cleaned-inshell or shelled peanuts or other activity causing peanuts to enter into...

  4. 7 CFR 1207.307 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in...

  5. 7 CFR 1207.307 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in...

  6. 7 CFR 1207.307 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in...

  7. 7 CFR 1207.307 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in...

  8. 7 CFR 1207.307 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in...

  9. 9 CFR 3.66 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Handling. 3.66 Section 3.66 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL... Transportation Standards § 3.66 Handling. (a) Any person who is subject to the Animal Welfare regulations and...

  10. 9 CFR 3.118 - Handling.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine Mammals Transportation Standards § 3.118...

  11. 29 CFR 1926.953 - Material handling.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 29 Labor 8 2014-07-01 2014-07-01 false Material handling. 1926.953 Section 1926.953 Labor... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the... shall be attached to the trailing end of the longest pole. (c) Storage. (1) No materials or...

  12. 29 CFR 1926.953 - Material handling.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 8 2011-07-01 2011-07-01 false Material handling. 1926.953 Section 1926.953 Labor... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the... shall be attached to the trailing end of the longest pole. (c) Storage. (1) No materials or...

  13. 29 CFR 1926.953 - Material handling.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 29 Labor 8 2012-07-01 2012-07-01 false Material handling. 1926.953 Section 1926.953 Labor... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the... shall be attached to the trailing end of the longest pole. (c) Storage. (1) No materials or...

  14. 29 CFR 1926.953 - Material handling.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 29 Labor 8 2013-07-01 2013-07-01 false Material handling. 1926.953 Section 1926.953 Labor... Material handling. (a) Unloading. Prior to unloading steel, poles, cross arms and similar material, the... shall be attached to the trailing end of the longest pole. (c) Storage. (1) No materials or...

  15. 7 CFR 926.9 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current...

  16. 7 CFR 926.9 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current...

  17. 7 CFR 926.9 - Handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current...

  18. 7 CFR 926.9 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current...

  19. 7 CFR 926.9 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current...

  20. 7 CFR 983.14 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling,...

  1. 7 CFR 983.14 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling,...

  2. 7 CFR 983.14 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling,...

  3. 7 CFR 983.14 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling,...

  4. 7 CFR 1219.11 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass...

  5. Moving and handling: reducing risk through assessment.

    PubMed

    Warren, Gemma

    2016-06-01

    Manual handling injuries can occur almost anywhere in a healthcare environment, and most staff perform a variety of moving and handling tasks every day. Heavy lifting, awkward posture, and previous or existing injury can increase the risk of musculoskeletal disorders. A healthcare professional's involvement in moving and handling is more widespread than it might appear, and their actions and understanding of techniques, legislation and guidelines have a direct effect on patient care. Every situation that involves the handling, or partial handling, of a person presents varying levels of risk to the patient and the carer. Maintaining a good level of patient mobility and independence is an essential part of care delivery and can reduce the risk of long-term physical and psychological effects. Delivery of care should focus on the individual's capacity, not their incapacity, to ensure that they are treated with dignity and respect.

  6. Syntactic Reordering for Arabic- English Phrase-Based Machine Translation

    NASA Astrophysics Data System (ADS)

    Hatem, Arwa; Omar, Nazlia

    Machine Translation (MT) refers to the use of a machine for performing translation task which converts text or speech in one Natural Language (Source Language (SL)) into another Natural Language (Target Language (TL)). The translation from Arabic to English is difficult task due to the Arabic languages are highly inflectional, rich morphology and relatively free word order. Word ordering plays an important part in the translation process. The paper proposes a transfer-based approach in Arabic to English MT to handle the word ordering problem. Preliminary tested indicate that our system, AE-TBMT is competitive when compared against other approaches from the literature.

  7. Handling Procedures of Vegetable Crops

    NASA Technical Reports Server (NTRS)

    Perchonok, Michele; French, Stephen J.

    2004-01-01

    The National Aeronautics and Space Administration (NASA) is working towards future long duration manned space flights beyond low earth orbit. The duration of these missions may be as long as 2.5 years and will likely include a stay on a lunar or planetary surface. The primary goal of the Advanced Food System in these long duration exploratory missions is to provide the crew with a palatable, nutritious, and safe food system while minimizing volume, mass, and waste. Vegetable crops can provide the crew with added nutrition and variety. These crops do not require any cooking or food processing prior to consumption. The vegetable crops, unlike prepackaged foods, will provide bright colors, textures (crispy), and fresh aromas. Ten vegetable crops have been identified for possible use in long duration missions. They are lettuce, spinach, carrot, tomato, green onion, radish, bell pepper, strawberries, fresh herbs, and cabbage. Whether these crops are grown on a transit vehicle (e.g., International Space Station) or on the lunar or planetary surface, it will be necessary to determine how to safely handle the vegetables while maintaining acceptability. Since hydrogen peroxide degrades into water and oxygen and is generally recognized as safe (GRAS), hydrogen peroxide has been recommended as the sanitizer. The objective of th is research is to determine the required effective concentration of hydrogen peroxide. In addition, it will be determined whether the use of hydrogen peroxide, although a viable sanitizer, adversely affects the quality of the vegetables. Vegetables will be dipped in 1 % hydrogen peroxide, 3% hydrogen peroxide, or 5% hydrogen peroxide. Treated produce and controls will be stored in plastic bags at 5 C for up to 14 days. Sensory, color, texture, and total plate count will be measured. The effect on several vegetables including lettuce, radish, tomato and strawberries has been completed. Although each vegetable reacts to hydrogen peroxide differently, the

  8. Data Machine Independence

    1994-12-30

    Data-machine independence achieved by using four technologies (ASN.1, XDR, SDS, and ZEBRA) has been evaluated by encoding two different applications in each of the above; and their results compared against the standard programming method using C.

  9. The TUM walking machines.

    PubMed

    Pfeiffer, Friedrich

    2007-01-15

    This paper presents some aspects of walking machine design with a special emphasis on the three machines MAX, MORITZ and JOHNNIE, having been developed at the Technical University of Munich within the last 20 years. The design of such machines is discussed as an iterative process improving the layout with every iteration. The control concepts are event-driven and follow logical rules, which have largely been transferred from neurobiological findings. At least for the six-legged machine MAX, a nearly perfect autonomy could be achieved, whereas for the biped JOHNNIE, a certain degree of autonomy could be realized by a vision system with appropriate decision algorithms. This vision system was developed by the group of Prof. G. Schmidt, TU-München. A more detailed description of the design and realization is presented for the biped JOHNNIE.

  10. Laser machining of ceramic

    SciTech Connect

    Laudel, A.

    1980-01-01

    The Kansas City Division of The Bendix Corporation manufactures hybrid microcircuits (HMCs) using both thin film and thick film technologies. Laser machining is used to contour the ceramic substrates and to drill holes in the ceramic for frontside-backside interconnections (vias) and holes for mounting components. A 1000 W CO/sub 2/ type laser is used. The laser machining process, and methods used for removing protruding debris and debris from holes, for cleaning the machined surfaces, and for refiring are described. The laser machining process described consistently produces vias, component holes and contours with acceptable surface quality, hole locations, diameter, flatness and metallization adhesion. There are no cracks indicated by dipping in fluorescent dye penetrant and the substances are resistant to repeated thermal shock.

  11. 16. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    16. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific Railroad Carlin Shops, view to south (90mm lens). Note the large segmental-arched doorway to move locomotives in and out of Machine Shop. - Southern Pacific Railroad, Carlin Shops, Roundhouse Machine Shop Extension, Foot of Sixth Street, Carlin, Elko County, NV

  12. "Paper Machine" for Molecular Diagnostics.

    PubMed

    Connelly, John T; Rolland, Jason P; Whitesides, George M

    2015-08-01

    Clinical tests based on primer-initiated amplification of specific nucleic acid sequences achieve high levels of sensitivity and specificity. Despite these desirable characteristics, these tests have not reached their full potential because their complexity and expense limit their usefulness to centralized laboratories. This paper describes a device that integrates sample preparation and loop-mediated isothermal amplification (LAMP) with end point detection using a hand-held UV source and camera phone. The prototype device integrates paper microfluidics (to enable fluid handling) and a multilayer structure, or a "paper machine", that allows a central patterned paper strip to slide in and out of fluidic path and thus allows introduction of sample, wash buffers, amplification master mix, and detection reagents with minimal pipetting, in a hand-held, disposable device intended for point-of-care use in resource-limited environments. This device creates a dynamic seal that prevents evaporation during incubation at 65 °C for 1 h. This interval is sufficient to allow a LAMP reaction for the Escherichia coli malB gene to proceed with an analytical sensitivity of 1 double-stranded DNA target copy. Starting with human plasma spiked with whole, live E. coli cells, this paper demonstrates full integration of sample preparation with LAMP amplification and end point detection with a limit of detection of 5 cells. Further, it shows that the method used to prepare sample enables concentration of DNA from sample volumes commonly available from fingerstick blood draw.

  13. "Paper Machine" for Molecular Diagnostics.

    PubMed

    Connelly, John T; Rolland, Jason P; Whitesides, George M

    2015-08-01

    Clinical tests based on primer-initiated amplification of specific nucleic acid sequences achieve high levels of sensitivity and specificity. Despite these desirable characteristics, these tests have not reached their full potential because their complexity and expense limit their usefulness to centralized laboratories. This paper describes a device that integrates sample preparation and loop-mediated isothermal amplification (LAMP) with end point detection using a hand-held UV source and camera phone. The prototype device integrates paper microfluidics (to enable fluid handling) and a multilayer structure, or a "paper machine", that allows a central patterned paper strip to slide in and out of fluidic path and thus allows introduction of sample, wash buffers, amplification master mix, and detection reagents with minimal pipetting, in a hand-held, disposable device intended for point-of-care use in resource-limited environments. This device creates a dynamic seal that prevents evaporation during incubation at 65 °C for 1 h. This interval is sufficient to allow a LAMP reaction for the Escherichia coli malB gene to proceed with an analytical sensitivity of 1 double-stranded DNA target copy. Starting with human plasma spiked with whole, live E. coli cells, this paper demonstrates full integration of sample preparation with LAMP amplification and end point detection with a limit of detection of 5 cells. Further, it shows that the method used to prepare sample enables concentration of DNA from sample volumes commonly available from fingerstick blood draw. PMID:26104869

  14. Doubly fed induction machine

    DOEpatents

    Skeist, S. Merrill; Baker, Richard H.

    2005-10-11

    An electro-mechanical energy conversion system coupled between an energy source and an energy load including an energy converter device having a doubly fed induction machine coupled between the energy source and the energy load to convert the energy from the energy source and to transfer the converted energy to the energy load and an energy transfer multiplexer coupled to the energy converter device to control the flow of power or energy through the doubly fed induction machine.

  15. Flexible machining systems described

    NASA Astrophysics Data System (ADS)

    Butters, H. J.

    1985-03-01

    The rationalization and gradual automation of short rotationally symmetric parts in the Saalfeld VEB Machine Tool Factory was carried out in three stages: (1) part-specific manufacturing; (2) automated production line for manufacturing toothed gears; and (3) automated manufacturing section for short rotationally symmetric parts. The development of numerically controlled machine tools and of industrial robot technology made possible automated manufacturing. The design of current facilities is explored, manufacturing control is examined, experience is reported.

  16. Human-machine interactions

    DOEpatents

    Forsythe, J. Chris; Xavier, Patrick G.; Abbott, Robert G.; Brannon, Nathan G.; Bernard, Michael L.; Speed, Ann E.

    2009-04-28

    Digital technology utilizing a cognitive model based on human naturalistic decision-making processes, including pattern recognition and episodic memory, can reduce the dependency of human-machine interactions on the abilities of a human user and can enable a machine to more closely emulate human-like responses. Such a cognitive model can enable digital technology to use cognitive capacities fundamental to human-like communication and cooperation to interact with humans.

  17. Metalworking and machining fluids

    DOEpatents

    Erdemir, Ali; Sykora, Frank; Dorbeck, Mark

    2010-10-12

    Improved boron-based metal working and machining fluids. Boric acid and boron-based additives that, when mixed with certain carrier fluids, such as water, cellulose and/or cellulose derivatives, polyhydric alcohol, polyalkylene glycol, polyvinyl alcohol, starch, dextrin, in solid and/or solvated forms result in improved metalworking and machining of metallic work pieces. Fluids manufactured with boric acid or boron-based additives effectively reduce friction, prevent galling and severe wear problems on cutting and forming tools.

  18. Sealing intersecting vane machines

    DOEpatents

    Martin, Jedd N.; Chomyszak, Stephen M.

    2007-06-05

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through intersecting surfaces without the need for external gearing by modifying the width of one or both tracks at the point of intermeshing. The inventions described herein relate to these improvements.

  19. Sealing intersecting vane machines

    DOEpatents

    Martin, Jedd N.; Chomyszak, Stephen M.

    2005-06-07

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through intersecting surfaces without the need for external gearing by modifying the width of one or both tracks at the point of intermeshing. The inventions described herein relate to these improvements.

  20. A Function Machine

    ERIC Educational Resources Information Center

    Hewitt, Dave

    2008-01-01

    In this article, the author describes a lesson he observed involving a function machine. This function machine was a box with a slot at the top of one side and a large cut-out hole at the bottom of the opposite side. A card with a number written on it (the input) was pushed into the slot and the teacher put their hand through the hole of the other…

  1. Opticam PM machine design

    NASA Astrophysics Data System (ADS)

    Liedes, Jyrki T.

    1992-12-01

    Rank Pneumo has worked with the Center for Optics Manufacturing and the Center's Manufacturing Advisory Board to design a multi-axis prism grinding machine. The Opticam PM is a three axis, high precision CNC reciprocating grinder. It is designed for the automated manufacturing of glass prisms. Unique features of the design incorporate electrolytic in- process dressing of the finishing wheel, nested grinding wheels and machine resident metrology to provide RQM (Real-time Quality Management).

  2. Could a machine think

    SciTech Connect

    Churchland, P.M.; Churchland, P.S. )

    1990-01-01

    There are many reasons for saying yes. One of the earliest and deepest reason lay in two important results in computational theory. The first was Church's thesis, which states that every effectively computable function is recursively computable. The second important result was Alan M. Turing's demonstration that any recursively computable function can be computed in finite time by a maximally simple sort of symbol-manipulating machine that has come to be called a universal Turing machine. This machine is guided by a set of recursively applicable rules that are sensitive to the identity, order and arrangement of the elementary symbols it encounters as input. The authors reject the Turing test as a sufficient condition for conscious intelligence. They base their position of the specific behavioral failures of the classical SM machines and on the specific virtues of machines with a more brain-like architecture. These contrasts show that certain computational strategies have vast and decisive advantages over others where typical cognitive tasks are concerned, advantages that are empirically inescapable. Clearly, the brain is making systematic use of these computational advantage. But it need not be the only physical system capable of doing so. Artificial intelligence, in a nonbiological but massively parallel machine, remain a compelling and discernible prospect.

  3. Integrated robotic vehicle control system for outdoor container handling

    NASA Astrophysics Data System (ADS)

    Viitanen, Jouko O.; Haverinen, Janne; Mattila, Pentti; Maekelae, Hannu; von Numers, Thomas; Stanek, Zbigniev; Roening, Juha

    1997-09-01

    We describe an integrated system developed for use onboard a moving work machine. The machine is targeted to such applications as e.g. automatic container handling at loading terminals. The main emphasis is on the various environment perception duties required by autonomous or semi-autonomous operation. These include obstacle detection, container position determination, localization needed for efficient navigation and measurement of docking and grasping locations of containers. Practical experience is reported on the use of several different types of technologies for the tasks. For close distance measurement, such as container row following, ultrasonic measurement was used, with associated control software. For obstacle and docking position detection, 3D active vision techniques were developed with structured lighting, utilizing also motion estimation techniques. Depth from defocus-based methods were developed for passive 3D vision. For localization, fusion of data from several sources was carried out. These included dead-reckoning data from odometry, an inertial unit, and several alternative external localization devices, i.e. real-time kinematic GPS, inductive and optical transponders. The system was integrated to run on a real-time operating system platform, using a high-level software specification tool that created the hierarchical control structure of the software.

  4. Laryngoscope handles: a potential for infection.

    PubMed

    Simmons, S A

    2000-06-01

    Laryngoscope handles do not usually come in direct contact with the patient's mucous membranes. Consequently, routine disinfection of laryngoscope handles is not currently standard practice unless gross contamination is clearly evident. Recent reports indicate that apparently clean handles may be contaminated with blood or body fluids. No report examined microbes on handles. The present article describes the incidence and types of microbes on laryngoscope handles after their use in the operating rooms of a 502-bed medical center in northwestern Pennsylvania. Twenty laryngoscope handles were cultured on Mueller Hinton 5% sheep blood agar plates. The plates were incubated at 37 degrees C for 48 hours and examined for growth. The identification, incidence, and susceptibility patterns of organisms were determined. Microorganisms were present on all 20 laryngoscope handles. Nine different types were isolated; some strains were resistant to multiple antibiotics. Organisms were categorized as contaminants or opportunistic pathogens. The presence of opportunistic pathogens places anesthesia providers and patients at risk of nosocomial infections. Based on the recommendations of the 1997 American Association of Nurse Anesthetists' Infection Control Guide and the results of the present study, institutional guidelines should be established for the use of disposable laryngoscope covers, high-level (destroying all microorganisms with the exception of high numbers of bacterial spores) disinfection, or sterilization of laryngoscope equipment between each patient use.

  5. The Knife Machine. Module 15.

    ERIC Educational Resources Information Center

    South Carolina State Dept. of Education, Columbia. Office of Vocational Education.

    This module on the knife machine, one in a series dealing with industrial sewing machines, their attachments, and operation, covers one topic: performing special operations on the knife machine (a single needle or multi-needle machine which sews and cuts at the same time). These components are provided: an introduction, directions, an objective,…

  6. Feedback in sequential machine realizations.

    NASA Technical Reports Server (NTRS)

    Harlow, C. A.; Coates, C. L., Jr.

    1972-01-01

    A method is described for determining the realizability of a sequential machine with trigger or set-reset flip-flop memory elements when the feedback of the machine is given by a Boolean function. Feedbacks in several types of sequential machines with different memory elements are compared, showing the memory specifications allowing the realization of such machines.

  7. Mooring and ground handling rigid airships

    NASA Technical Reports Server (NTRS)

    Walker, H., Jr.

    1975-01-01

    The problems of mooring and ground handling rigid airships are discussed. A brief history of Mooring and Ground Handling Rigid Airships from July 2, 1900 through September 1, 1939 is included. Also a brief history of ground handling developments with large U. S. Navy nonrigid airships between September 1, 1939 and August 31, 1962 is included wherein developed equipment and techniques appear applicable to future large rigid airships. Finally recommendations are made pertaining to equipment and procedures which appear desirable and feasible for future rigid airship programs.

  8. Cost of Information Handling in Hospitals

    PubMed Central

    Jydstrup, Ronald A.; Gross, Malvern J.

    1966-01-01

    Cost of information handling (noncomputerized) in hospitals was studied in detail from an industrial engineering point of view at Rochester General, Highland, and Geneva General hospitals. Activities were observed, personnel questioned, and time studies carried out. It was found that information handling comprises about one fourth of the hospitals' operating cost—a finding strongly recommending revision and streamlining of both forms and inefficient operations. In an Appendix to this study are presented 15 items that would improve information handling in one area of the hospital, nursing units, where this activity is greater than in any other in a hospital. PMID:5971636

  9. Handling time and choice in pigeons.

    PubMed

    Shettleworth, S J

    1985-09-01

    According to optimal foraging theory, animals should prefer food items with the highest ratios of energy intake to handling time. When single items have negligible handling times, one large item should be preferred to a collection of small ones of equivalent total weight. However, when pigeons were offered such a choice on equal concurrent variable-interval schedules in a shuttlebox, they preferred the side offering many small items per reinforcement to that offering one or a few relatively large items. This preference was still evident on concurrent fixed-cumulative-duration schedules in which choosing the alternative with longer handling time substantially lowered the rate of food intake.

  10. How the NWC handles software as product

    SciTech Connect

    Vinson, D.

    1997-11-01

    This tutorial provides a hands-on view of how the Nuclear Weapons Complex project should be handling (or planning to handle) software as a product in response to Engineering Procedure 401099. The SQAS has published the document SQAS96-002, Guidelines for NWC Processes for Handling Software Product, that will be the basis for the tutorial. The primary scope of the tutorial is on software products that result from weapons and weapons-related projects, although the information presented is applicable to many software projects. Processes that involve the exchange, review, or evaluation of software product between or among NWC sites, DOE, and external customers will be described.

  11. Non-traditional machining techniques

    SciTech Connect

    Day, Robert D; Fierro, Frank; Garcia, Felix P; Hatch, Douglass J; Randolph, Randall B; Reardon, Patrick T; Rivera, Gerald

    2008-01-01

    During the course of machining targets for various experiments it sometimes becomes necessary to adapt fixtures or machines, which are designed for one function, to another function. When adapting a machine or fixture is not adequate, it may be necessary to acquire a machine specifically designed to produce the component required. In addition to the above scenarios, the features of a component may dictate that multi-step machining processes are necessary to produce the component. This paper discusses the machining of four components where adaptation, specialized machine design, or multi-step processes were necessary to produce the components.

  12. Handle Fireworks with Care on The Fourth

    MedlinePlus

    ... https://medlineplus.gov/news/fullstory_159649.html Handle Fireworks With Care on the Fourth Take steps to ... THURSDAY, June 30, 2016 (HealthDay News) -- Americans love fireworks, especially on the Fourth of July, but experts ...

  13. Flat-package DIP handling tool

    NASA Technical Reports Server (NTRS)

    Angelou, E.; Fraser, R.

    1977-01-01

    Device, using magnetic attraction, can facilitate handling of integrated-circuit flat packages and prevent contamination and bent leads. Tool lifts packages by their cases and releases them by operation of manual plunger.

  14. Intertextuality for Handling Complex Environmental Issues

    NASA Astrophysics Data System (ADS)

    Byhring, Anne Kristine; Knain, Erik

    2016-02-01

    Nowhere is the need for handling complexity more pertinent than in addressing environmental issues. Our study explores students' situated constructs of complexity in unfolding discourses on socio-scientific issues. Students' dialogues in two group-work episodes are analysed in detail, with tools from Systemic Functional Linguistics. We identify the significance of intertextuality in students' realizations of low- and high-complexity discourses. In the high-complexity event, we show how students take on different roles and use modality and projection as grammatical resources for opening up, for different positions, multiple voices, and various contextual resources. Successful handling of complexity is construed by the interplay between students' roles in the discourse and resources in language for making multiple voices present. In the high-complexity event, the handling of complexity is guided by the students' sense of purpose. Handling complexity is demanding, and explicit scaffolding is necessary to prevent a potentially complex challenge from being treated as a simple one.

  15. 9 CFR 3.142 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... be exercised to avoid handling of the primary enclosure in such a manner that may cause physical or emotional trauma to the live animal contained therein. (c) Primary enclosures used to transport any...

  16. 9 CFR 3.142 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... be exercised to avoid handling of the primary enclosure in such a manner that may cause physical or emotional trauma to the live animal contained therein. (c) Primary enclosures used to transport any...

  17. 9 CFR 3.142 - Handling.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... be exercised to avoid handling of the primary enclosure in such a manner that may cause physical or emotional trauma to the live animal contained therein. (c) Primary enclosures used to transport any...

  18. 9 CFR 3.142 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... be exercised to avoid handling of the primary enclosure in such a manner that may cause physical or emotional trauma to the live animal contained therein. (c) Primary enclosures used to transport any...

  19. 9 CFR 3.142 - Handling.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... be exercised to avoid handling of the primary enclosure in such a manner that may cause physical or emotional trauma to the live animal contained therein. (c) Primary enclosures used to transport any...

  20. The Bearingless Electrical Machine

    NASA Technical Reports Server (NTRS)

    Bichsel, J.

    1992-01-01

    Electromagnetic bearings allow the suspension of solids. For rotary applications, the most important physical effect is the force of a magnetic circuit to a high permeable armature, called the MAXWELL force. Contrary to the commonly used MAXWELL bearings, the bearingless electrical machine will take advantage of the reaction force of a conductor carrying a current in a magnetic field. This kind of force, called Lorentz force, generates the torque in direct current, asynchronous and synchronous machines. The magnetic field, which already exists in electrical machines and helps to build up the torque, can also be used for the suspension of the rotor. Besides the normal winding of the stator, a special winding was added, which generates forces for levitation. So a radial bearing, which is integrated directly in the active part of the machine, and the motor use the laminated core simultaneously. The winding was constructed for the levitating forces in a special way so that commercially available standard ac inverters for drives can be used. Besides wholly magnetic suspended machines, there is a wide range of applications for normal drives with ball bearings. Resonances of the rotor, especially critical speeds, can be damped actively.

  1. Non Contact Measuring Machine

    NASA Astrophysics Data System (ADS)

    Carvalho, Fernando D.; Sebastiao, Pedro; Henriques, Bernardo G.

    1989-01-01

    One of the problems of the production of cables is the measurement of the thickness plastic cover at the production line. If for some reason the thickness of the plastic is smaller than the minimum necessary several meters of cable may be lost. If the problem exists in the middle of a long cable and the default is not detected in time, the loss will be significant. To solve this problem it is possible to use automatic measuring machines which may detect a default as soon as it happens. It is also possible to interact with the production line in order to avoid any losses. In this paper it is presented a non contact measuring machine, developed for this purpose. The machine uses a laser which is scanned through a field of 80 mm. The interruption of the beam gives information about the external dimension of the object. The technical study of the resolution, sensitivity and precision are presented on the paper. Also the hardware solution and the software are presented. The machine has an interface which allows communication with a PC. The PC may receive information from several measuring units and to interact with machines installed at the production line. The prototype is finished and is going to be tested in the industry.

  2. Extreme ultraviolet lithography machine

    SciTech Connect

    Tichenor, D.A.; Kubiak, G.D.; Haney, S.J.; Sweeney, D.W.

    2000-02-29

    An extreme ultraviolet lithography (EUVL) machine or system is disclosed for producing integrated circuit (IC) components, such as transistors, formed on a substrate. The EUVL machine utilizes a laser plasma point source directed via an optical arrangement onto a mask or reticle which is reflected by a multiple mirror system onto the substrate or target. The EUVL machine operates in the 10--14 nm wavelength soft x-ray photon. Basically the EUV machine includes an evacuated source chamber, an evacuated main or project chamber interconnected by a transport tube arrangement, wherein a laser beam is directed into a plasma generator which produces an illumination beam which is directed by optics from the source chamber through the connecting tube, into the projection chamber, and onto the reticle or mask, from which a patterned beam is reflected by optics in a projection optics (PO) box mounted in the main or projection chamber onto the substrate. In one embodiment of a EUVL machine, nine optical components are utilized, with four of the optical components located in the PO box. The main or projection chamber includes vibration isolators for the PO box and a vibration isolator mounting for the substrate, with the main or projection chamber being mounted on a support structure and being isolated.

  3. Extreme ultraviolet lithography machine

    DOEpatents

    Tichenor, Daniel A.; Kubiak, Glenn D.; Haney, Steven J.; Sweeney, Donald W.

    2000-01-01

    An extreme ultraviolet lithography (EUVL) machine or system for producing integrated circuit (IC) components, such as transistors, formed on a substrate. The EUVL machine utilizes a laser plasma point source directed via an optical arrangement onto a mask or reticle which is reflected by a multiple mirror system onto the substrate or target. The EUVL machine operates in the 10-14 nm wavelength soft x-ray photon. Basically the EUV machine includes an evacuated source chamber, an evacuated main or project chamber interconnected by a transport tube arrangement, wherein a laser beam is directed into a plasma generator which produces an illumination beam which is directed by optics from the source chamber through the connecting tube, into the projection chamber, and onto the reticle or mask, from which a patterned beam is reflected by optics in a projection optics (PO) box mounted in the main or projection chamber onto the substrate. In one embodiment of a EUVL machine, nine optical components are utilized, with four of the optical components located in the PO box. The main or projection chamber includes vibration isolators for the PO box and a vibration isolator mounting for the substrate, with the main or projection chamber being mounted on a support structure and being isolated.

  4. Meso-Machining Capabilities

    SciTech Connect

    BENAVIDES,GILBERT L.; ADAMS,DAVID P.; YANG,PIN

    2001-06-01

    Meso-scale manufacturing processes are bridging the gap between silicon-based MEMS processes and conventional miniature machining. These processes can fabricate two and three-dimensional parts having micron size features in traditional materials such as stainless steels, rare earth magnets, ceramics, and glass. Meso-scale processes that are currently available include, focused ion beam sputtering, micro-milling, micro-turning, excimer laser ablation, femtosecond laser ablation, and micro electro discharge machining. These meso-scale processes employ subtractive machining technologies (i.e., material removal), unlike LIGA, which is an additive meso-scale process. Meso-scale processes have different material capabilities and machining performance specifications. Machining performance specifications of interest include minimum feature size, feature tolerance, feature location accuracy, surface finish, and material removal rate. Sandia National Laboratories is developing meso-scale mechanical components and actuators which require meso-scale parts fabricated in a variety of materials. Subtractive meso-scale manufacturing processes expand the functionality of meso-scale components and complement silicon based MEMS and LIGA technologies.

  5. Machinable oxide ceramic

    SciTech Connect

    Rayne, R.J.; Toth, L.E.; Jones, L.D.; Soulen, R.J. Jr.; Bender, B.A.

    1993-06-01

    A method of forming a machinable bulk superconductor by melt-casting the described comprising the steps of: weighing out amounts of powdered SrCO[sub 3], CuO, CaCO[sub 3], and Bi[sub 2]O[sub 3] for the desired stoichiometry of the superconductor; combining the amounts of Bi[sub 2]O[sub 3], SrCO[sub 3], CuO and CaCO[sub 3] to form a mixture of uniform color; removing the carbonates in the mixture; heating the mixture until the mixture melts completely, to form a melt; pouring the melt into a preheated, non-reactive mold; cooling the melted mixture in the mold to room temperature, to form a casting; inducing a superconducting phase having randomly oriented platelets within the casting; and machining, by a metal cutting technique, said casting having said induced superconducting phase; wherein said machining step is performed with a steel tool.

  6. Micro-machined resonator

    DOEpatents

    Godshall, Ned A.; Koehler, Dale R.; Liang, Alan Y.; Smith, Bradley K.

    1993-01-01

    A micro-machined resonator, typically quartz, with upper and lower micro-machinable support members, or covers, having etched wells which may be lined with conductive electrode material, between the support members is a quartz resonator having an energy trapping quartz mesa capacitively coupled to the electrode through a diaphragm; the quartz resonator is supported by either micro-machined cantilever springs or by thin layers extending over the surfaces of the support. If the diaphragm is rigid, clock applications are available, and if the diaphragm is resilient, then transducer applications can be achieved. Either the thin support layers or the conductive electrode material can be integral with the diaphragm. In any event, the covers are bonded to form a hermetic seal and the interior volume may be filled with a gas or may be evacuated. In addition, one or both of the covers may include oscillator and interface circuitry for the resonator.

  7. Micro-machined resonator

    DOEpatents

    Godshall, N.A.; Koehler, D.R.; Liang, A.Y.; Smith, B.K.

    1993-03-30

    A micro-machined resonator, typically quartz, with upper and lower micro-machinable support members, or covers, having etched wells which may be lined with conductive electrode material, between the support members is a quartz resonator having an energy trapping quartz mesa capacitively coupled to the electrode through a diaphragm; the quartz resonator is supported by either micro-machined cantilever springs or by thin layers extending over the surfaces of the support. If the diaphragm is rigid, clock applications are available, and if the diaphragm is resilient, then transducer applications can be achieved. Either the thin support layers or the conductive electrode material can be integral with the diaphragm. In any event, the covers are bonded to form a hermetic seal and the interior volume may be filled with a gas or may be evacuated. In addition, one or both of the covers may include oscillator and interface circuitry for the resonator.

  8. Automated fiber pigtailing machine

    DOEpatents

    Strand, O.T.; Lowry, M.E.

    1999-01-05

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectronic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems. 26 figs.

  9. Automated fiber pigtailing machine

    DOEpatents

    Strand, Oliver T.; Lowry, Mark E.

    1999-01-01

    The Automated Fiber Pigtailing Machine (AFPM) aligns and attaches optical fibers to optoelectonic (OE) devices such as laser diodes, photodiodes, and waveguide devices without operator intervention. The so-called pigtailing process is completed with sub-micron accuracies in less than 3 minutes. The AFPM operates unattended for one hour, is modular in design and is compatible with a mass production manufacturing environment. This machine can be used to build components which are used in military aircraft navigation systems, computer systems, communications systems and in the construction of diagnostics and experimental systems.

  10. New photolithography stepping machine

    SciTech Connect

    Hale, L.; Klingmann, J.; Markle, D.

    1995-03-08

    A joint development project to design a new photolithography steeping machine capable of 150 nanometer overlay accuracy was completed by Ultratech Stepper and the Lawrence Livermore National Laboratory. The principal result of the project is a next-generation product that will strengthen the US position in step-and-repeat photolithography. The significant challenges addressed and solved in the project are the subject of this report. Design methods and new devices that have broader application to precision machine design are presented in greater detail while project specific information serves primarily as background and motivation.

  11. Precision Robotic Assembly Machine

    ScienceCinema

    None

    2016-07-12

    The world's largest laser system is the National Ignition Facility (NIF), located at Lawrence Livermore National Laboratory. NIF's 192 laser beams are amplified to extremely high energy, and then focused onto a tiny target about the size of a BB, containing frozen hydrogen gas. The target must be perfectly machined to incredibly demanding specifications. The Laboratory's scientists and engineers have developed a device called the "Precision Robotic Assembly Machine" for this purpose. Its unique design won a prestigious R&D-100 award from R&D Magazine.

  12. Precision Robotic Assembly Machine

    SciTech Connect

    2009-08-14

    The world's largest laser system is the National Ignition Facility (NIF), located at Lawrence Livermore National Laboratory. NIF's 192 laser beams are amplified to extremely high energy, and then focused onto a tiny target about the size of a BB, containing frozen hydrogen gas. The target must be perfectly machined to incredibly demanding specifications. The Laboratory's scientists and engineers have developed a device called the "Precision Robotic Assembly Machine" for this purpose. Its unique design won a prestigious R&D-100 award from R&D Magazine.

  13. Intersecting vane machines

    DOEpatents

    Bailey, H. Sterling; Chomyszak, Stephen M.

    2007-01-16

    The invention provides a toroidal intersecting vane machine incorporating intersecting rotors to form primary and secondary chambers whose porting configurations minimize friction and maximize efficiency. Specifically, it is an object of the invention to provide a toroidal intersecting vane machine that greatly reduces the frictional losses through meshing surfaces without the need for external gearing by modifying the function of one or the other of the rotors from that of "fluid moving" to that of "valving" thereby reducing the pressure loads and associated inefficiencies at the interface of the meshing surfaces. The inventions described herein relate to these improvements.

  14. Paradigms for machine learning

    NASA Technical Reports Server (NTRS)

    Schlimmer, Jeffrey C.; Langley, Pat

    1991-01-01

    Five paradigms are described for machine learning: connectionist (neural network) methods, genetic algorithms and classifier systems, empirical methods for inducing rules and decision trees, analytic learning methods, and case-based approaches. Some dimensions are considered along with these paradigms vary in their approach to learning, and the basic methods are reviewed that are used within each framework, together with open research issues. It is argued that the similarities among the paradigms are more important than their differences, and that future work should attempt to bridge the existing boundaries. Finally, some recent developments in the field of machine learning are discussed, and their impact on both research and applications is examined.

  15. Machine speech and speaking about machines

    SciTech Connect

    Nye, A.

    1996-12-31

    Current philosophy of language prides itself on scientific status. It boasts of being no longer contaminated with queer mental entities or idealist essences. It theorizes language as programmable variants of formal semantic systems, reimaginable either as the properly epiphenomenal machine functions of computer science or the properly material neural networks of physiology. Whether or not such models properly capture the physical workings of a living human brain is a question that scientists will have to answer. I, as a philosopher, come at the problem from another direction. Does contemporary philosophical semantics, in its dominant truth-theoretic and related versions, capture actual living human thought as it is experienced, or does it instead reflect, regardless of (perhaps dubious) scientific credentials, pathology of thought, a pathology with a disturbing social history.

  16. 12. Photocopied August 1978. CHANNELING MACHINES, NOVEMBER 1898. THESE MACHINES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    12. Photocopied August 1978. CHANNELING MACHINES, NOVEMBER 1898. THESE MACHINES BLOCKED OUT SECTIONS IN THE ROCK CUT IN PREPARATION FOR DRILLING AND BLASTING. (17) - Michigan Lake Superior Power Company, Portage Street, Sault Ste. Marie, Chippewa County, MI

  17. BRASS FOUNDRY MACHINE ROOM USED TO MACHINE CAST BRONZE PIECES ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BRASS FOUNDRY MACHINE ROOM USED TO MACHINE CAST BRONZE PIECES FOR VALVES AND PREPARE BRONZE VALVE BODIES FOR ASSEMBLY. - Stockham Pipe & Fittings Company, Brass Foundry, 4000 Tenth Avenue North, Birmingham, Jefferson County, AL

  18. 14. Machine in north 1922 section of Building 59. Machine ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. Machine in north 1922 section of Building 59. Machine is 24' Jointer made by Oliver Machinery Co. Camera pointed E. - Puget Sound Naval Shipyard, Pattern Shop, Farragut Avenue, Bremerton, Kitsap County, WA

  19. A Turing Machine Simulator.

    ERIC Educational Resources Information Center

    Navarro, Aaron B.

    1981-01-01

    Presents a program in Level II BASIC for a TRS-80 computer that simulates a Turing machine and discusses the nature of the device. The program is run interactively and is designed to be used as an educational tool by computer science or mathematics students studying computational or automata theory. (MP)

  20. Support vector machines

    NASA Technical Reports Server (NTRS)

    Garay, Michael J.; Mazzoni, Dominic; Davies, Roger; Wagstaff, Kiri

    2004-01-01

    Support Vector Machines (SVMs) are a type of supervised learning algorith,, other examples of which are Artificial Neural Networks (ANNs), Decision Trees, and Naive Bayesian Classifiers. Supervised learning algorithms are used to classify objects labled by a 'supervisor' - typically a human 'expert.'.

  1. Electrical discharge machining.

    PubMed

    LaBarge, K W

    1997-11-01

    This article describes a laboratory technique of achieving the highest degree of passive fit of an implant-retained restoration using electric discharge machining (EDM). This process can save time by eliminating the need for conventional soldering procedures, increase the longevity of the restoration, and when used along with the clinical technique of fabricating a verification index, eliminate the clinical try-in phase.

  2. Laser machining of explosives

    SciTech Connect

    Perry, Michael D.; Stuart, Brent C.; Banks, Paul S.; Myers, Booth R.; Sefcik, Joseph A.

    2000-01-01

    The invention consists of a method for machining (cutting, drilling, sculpting) of explosives (e.g., TNT, TATB, PETN, RDX, etc.). By using pulses of a duration in the range of 5 femtoseconds to 50 picoseconds, extremely precise and rapid machining can be achieved with essentially no heat or shock affected zone. In this method, material is removed by a nonthermal mechanism. A combination of multiphoton and collisional ionization creates a critical density plasma in a time scale much shorter than electron kinetic energy is transferred to the lattice. The resulting plasma is far from thermal equilibrium. The material is in essence converted from its initial solid-state directly into a fully ionized plasma on a time scale too short for thermal equilibrium to be established with the lattice. As a result, there is negligible heat conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond a few microns from the laser machined surface. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces. There is no detonation or deflagration of the explosive in the process and the material which is removed is rendered inert.

  3. Cybernetic anthropomorphic machine systems

    NASA Technical Reports Server (NTRS)

    Gray, W. E.

    1974-01-01

    Functional descriptions are provided for a number of cybernetic man machine systems that augment the capacity of normal human beings in the areas of strength, reach or physical size, and environmental interaction, and that are also applicable to aiding the neurologically handicapped. Teleoperators, computer control, exoskeletal devices, quadruped vehicles, space maintenance systems, and communications equipment are considered.

  4. Working with Simple Machines

    ERIC Educational Resources Information Center

    Norbury, John W.

    2006-01-01

    A set of examples is provided that illustrate the use of work as applied to simple machines. The ramp, pulley, lever and hydraulic press are common experiences in the life of a student, and their theoretical analysis therefore makes the abstract concept of work more real. The mechanical advantage of each of these systems is also discussed so that…

  5. Biomimetic machine vision system.

    PubMed

    Harman, William M; Barrett, Steven F; Wright, Cameron H G; Wilcox, Michael

    2005-01-01

    Real-time application of digital imaging for use in machine vision systems has proven to be prohibitive when used within control systems that employ low-power single processors without compromising the scope of vision or resolution of captured images. Development of a real-time machine analog vision system is the focus of research taking place at the University of Wyoming. This new vision system is based upon the biological vision system of the common house fly. Development of a single sensor is accomplished, representing a single facet of the fly's eye. This new sensor is then incorporated into an array of sensors capable of detecting objects and tracking motion in 2-D space. This system "preprocesses" incoming image data resulting in minimal data processing to determine the location of a target object. Due to the nature of the sensors in the array, hyperacuity is achieved thereby eliminating resolutions issues found in digital vision systems. In this paper, we will discuss the biological traits of the fly eye and the specific traits that led to the development of this machine vision system. We will also discuss the process of developing an analog based sensor that mimics the characteristics of interest in the biological vision system. This paper will conclude with a discussion of how an array of these sensors can be applied toward solving real-world machine vision issues.

  6. Electrical Discharge Machining.

    ERIC Educational Resources Information Center

    Montgomery, C. M.

    The manual is for use by students learning electrical discharge machining (EDM). It consists of eight units divided into several lessons, each designed to meet one of the stated objectives for the unit. The units deal with: introduction to and advantages of EDM, the EDM process, basic components of EDM, reaction between forming tool and workpiece,…

  7. Machine-Aided Indexing.

    ERIC Educational Resources Information Center

    Jacobs, Charles R.

    Progress is reported at the 1,000,000 word level on the development of a partial syntatic analysis technique for indexing text. A new indexing subroutine for hyphens is provided. New grammars written and programmed for Machine Aided Indexing (MAI) are discussed. (ED 069 290 is a related document) (Author)

  8. The Art Machine.

    ERIC Educational Resources Information Center

    Vertelney, Harry; Grossberger, Lucia

    1983-01-01

    Introduces educators to possibilities of computer graphics using an inexpensive computer system which takes advantage of existing equipment (35mm camera, super 8 movie camera, VHS video cassette recorder). The concept of the "art machine" is explained, highlighting input and output devices (X-Y plotter, graphic tablets, video digitizers). (EJS)

  9. The Answer Machine.

    ERIC Educational Resources Information Center

    Feldman, Susan

    2000-01-01

    Discusses information retrieval systems and the need to have them adapt to user needs, integrate information in any format, reveal patterns and trends in information, and answer questions. Topics include statistics and probability; natural language processing; intelligent agents; concept mapping; machine-aided indexing; text mining; filtering;…

  10. Giving Machines the Vision

    NASA Technical Reports Server (NTRS)

    1999-01-01

    Amherst Systems manufactures foveal machine vision technology and systems commercially available to end-users and system integrators. This technology was initially developed under NASA contracts NAS9-19335 (Johnson Space Center) and NAS1-20841 (Langley Research Center). This technology is currently being delivered to university research facilities and military sites. More information may be found in www.amherst.com.

  11. Rotorcraft handling-qualities design criteria development

    NASA Technical Reports Server (NTRS)

    Aiken, Edwin W.; Lebacqz, J. Victor; Chen, Robert T. N.; Key, David L.

    1988-01-01

    Joint NASA/Army efforts at the Ames Research Center to develop rotorcraft handling-qualities design criteria began in earnest in 1975. Notable results were the UH-1H VSTOLAND variable stability helicopter, the VFA-2 camera-and-terrain-board simulator visual system, and the generic helicopter real-time mathematical model, ARMCOP. An initial series of handling-qualities studies was conducted to assess the effects of rotor design parameters, interaxis coupling, and various levels of stability and control augmentation. The ability to conduct in-flight handling-qualities research was enhanced by the development of the NASA/Army CH-47 variable-stability helicopter. Research programs conducted using this vehicle include vertical-response investigations, hover augmentation systems, and the effects of control-force characteristics. The handling-qualities data base was judged to be sufficient to allow an update of the military helicopter handling-qualities specification, MIL-H-8501. These efforts, including not only the in-house experimental work but also contracted research and collaborative programs performed under the auspices of various international agreements. The report concludes by reviewing the topics that are currently most in need of work, and the plans for addressing these topics.

  12. Handling Qualities Implications for Crewed Spacecraft Operations

    NASA Technical Reports Server (NTRS)

    Bailey, Randall E.; Jackson, E. Bruce; Arthur, J. J.

    2012-01-01

    Abstract Handling qualities embody those qualities or characteristics of an aircraft that govern the ease and precision with which a pilot is able to perform the tasks required in support of an aircraft role. These same qualities are as critical, if not more so, in the operation of spacecraft. A research, development, test, and evaluation process was put into effect to identify, understand, and interpret the engineering and human factors principles which govern the pilot-vehicle dynamic system as they pertain to space exploration missions and tasks. Toward this objective, piloted simulations were conducted at the NASA Langley Research Center and Ames Research Center for earth-orbit proximity operations and docking and lunar landing. These works provide broad guidelines for the design of spacecraft to exhibit excellent handling characteristics. In particular, this work demonstrates how handling qualities include much more than just stability and control characteristics of a spacecraft or aircraft. Handling qualities are affected by all aspects of the pilot-vehicle dynamic system, including the motion, visual and aural cues of the vehicle response as the pilot performs the required operation or task. A holistic approach to spacecraft design, including the use of manual control, automatic control, and pilot intervention/supervision is described. The handling qualities implications of design decisions are demonstrated using these pilot-in-the-loop evaluations of docking operations and lunar landings.

  13. Progress in Documentation: Machine Translation and Machine-Aided Translation.

    ERIC Educational Resources Information Center

    Hutchins, W. J.

    1978-01-01

    Discusses the prospects for fully automatic machine translation of good quality. Sections include history and background, operational and experimental machine translation systems of recent years, descriptions of interactive systems and machine-assisted translation, and a general survey of present problems and future possibilities. (VT)

  14. Tattoo machines, needles and utilities.

    PubMed

    Rosenkilde, Frank

    2015-01-01

    Starting out as a professional tattooist back in 1977 in Copenhagen, Denmark, Frank Rosenkilde has personally experienced the remarkable development of tattoo machines, needles and utilities: all the way from home-made equipment to industrial products of substantially improved quality. Machines can be constructed like the traditional dual-coil and single-coil machines or can be e-coil, rotary and hybrid machines, with the more convenient and precise rotary machines being the recent trend. This development has resulted in disposable needles and utilities. Newer machines are more easily kept clean and protected with foil to prevent crosscontaminations and infections. The machines and the tattooists' knowledge and awareness about prevention of infection have developed hand-in-hand. For decades, Frank Rosenkilde has been collecting tattoo machines. Part of his collection is presented here, supplemented by his personal notes. PMID:25833620

  15. Development of a Slim Manipulator Type Fuel Handling Machine for a Commercialized Fast Reactor

    SciTech Connect

    Yoshitaka Chikazawa; Shinichi Usui; Mamoru Konomura; Daisuke Sadahiro; Katsuhiro Tozawa; Toru Hori; Mikio Toda; Shoji Kotake

    2006-07-01

    A seismic analysis has been performed showing that the seismic interaction between the UIS and the FHM can be avoided eliminating the internal clearance of bearing at the FHM arm joint. An angular contact ball bearing is suitable for the new FHM since it can eliminate gaps by preload pressure. A major problem of the FHM bearings is lubrication since the contact pressure between the steel rings and ball of the ball bearing is larger than that of the roller bearing used in the previous design. Additionally, FHM operating temperature is about 200 deg-C and normal grease is not applicable under argon gas with sodium vapor to prevent contamination of grease in the primary sodium coolant. An endurance test with 1/10 scale bearings in the air has been performed to show applicability of angular contact ball bearings to the FHM arm joint. The results with 20,000 cycle showed that bearings with combination of MoS{sub 2} coating steel rings and ceramics balls can be tolerable as the FHM operating condition. A full-scale bearing test in argon gas with sodium vapor has also been demonstrated to reveal bearing size and sodium vapor effects. (authors)

  16. DOE handbook: Tritium handling and safe storage

    SciTech Connect

    1999-03-01

    The DOE Handbook was developed as an educational supplement and reference for operations and maintenance personnel. Most of the tritium publications are written from a radiological protection perspective. This handbook provides more extensive guidance and advice on the null range of tritium operations. This handbook can be used by personnel involved in the full range of tritium handling from receipt to ultimate disposal. Compliance issues are addressed at each stage of handling. This handbook can also be used as a reference for those individuals involved in real time determination of bounding doses resulting from inadvertent tritium releases. This handbook provides useful information for establishing processes and procedures for the receipt, storage, assay, handling, packaging, and shipping of tritium and tritiated wastes. It includes discussions and advice on compliance-based issues and adds insight to those areas that currently possess unclear DOE guidance.

  17. Fire-hazard control during coal handling

    SciTech Connect

    McGraw, M.G.

    1984-03-01

    The potential for serious power plant fires and explosions is growing along with the increased use of volatile, low-sulfur coal use and environmental regulations requiring closed conveyor systems for handling coal. The volume of coal handled and the range of physical characteristics in different coals intensifies the problem. Western coal produces more dust because it is more friable than eastern coal and is more prone to sponaneous combustion. Closed storage and handling systems increase the hazards of methane and carbon monoxide. The article described prevention, detection, and firefighting techniques, and notes that a variety of systems is needed to cover all the hazards. Human behavior and coordination are also essential ingredients. ll figures.

  18. Privacy preserving RBF kernel support vector machine.

    PubMed

    Li, Haoran; Xiong, Li; Ohno-Machado, Lucila; Jiang, Xiaoqian

    2014-01-01

    Data sharing is challenging but important for healthcare research. Methods for privacy-preserving data dissemination based on the rigorous differential privacy standard have been developed but they did not consider the characteristics of biomedical data and make full use of the available information. This often results in too much noise in the final outputs. We hypothesized that this situation can be alleviated by leveraging a small portion of open-consented data to improve utility without sacrificing privacy. We developed a hybrid privacy-preserving differentially private support vector machine (SVM) model that uses public data and private data together. Our model leverages the RBF kernel and can handle nonlinearly separable cases. Experiments showed that this approach outperforms two baselines: (1) SVMs that only use public data, and (2) differentially private SVMs that are built from private data. Our method demonstrated very close performance metrics compared to nonprivate SVMs trained on the private data. PMID:25013805

  19. Supernova Recognition using Support Vector Machines

    SciTech Connect

    Romano, Raquel A.; Aragon, Cecilia R.; Ding, Chris

    2006-10-01

    We introduce a novel application of Support Vector Machines(SVMs) to the problem of identifying potential supernovae usingphotometric and geometric features computed from astronomical imagery.The challenges of this supervised learning application are significant:1) noisy and corrupt imagery resulting in high levels of featureuncertainty,2) features with heavy-tailed, peaked distributions,3)extremely imbalanced and overlapping positiveand negative data sets, and4) the need to reach high positive classification rates, i.e. to find allpotential supernovae, while reducing the burdensome workload of manuallyexamining false positives. High accuracy is achieved viaasign-preserving, shifted log transform applied to features with peaked,heavy-tailed distributions. The imbalanced data problem is handled byoversampling positive examples,selectively sampling misclassifiednegative examples,and iteratively training multiple SVMs for improvedsupernovarecognition on unseen test data. We present crossvalidationresults and demonstrate the impact on a largescale supernova survey thatcurrently uses the SVM decision value to rank-order 600,000 potentialsupernovae each night.

  20. Automatically-Programed Machine Tools

    NASA Technical Reports Server (NTRS)

    Purves, L.; Clerman, N.

    1985-01-01

    Software produces cutter location files for numerically-controlled machine tools. APT, acronym for Automatically Programed Tools, is among most widely used software systems for computerized machine tools. APT developed for explicit purpose of providing effective software system for programing NC machine tools. APT system includes specification of APT programing language and language processor, which executes APT statements and generates NC machine-tool motions specified by APT statements.

  1. WASTE HANDLING BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect

    P.A. Kumar

    2000-06-21

    The Waste Handling Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Handling Building (WHB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for equipment operation and personnel comfort, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WHB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. The contamination confinement areas ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination within the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WHB. The Waste Handling Building Ventilation System is designed to perform its safety functions under accident conditions and other Design Basis Events (DBEs) (such as earthquakes, tornadoes, fires, and loss of the primary electric power). Additional system design features (such as compartmentalization with independent subsystems) limit the potential for cross-contamination within the WHB. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Handling Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits. The system design, operations, and maintenance activities incorporate ALARA (as low as is

  2. Intelligent material handling: use of vision

    NASA Astrophysics Data System (ADS)

    Dickerson, Stephen L.; Lee, Kok-Meng; Lee, Eun-Ho; Single, Thomas; Li, Da-ren

    1991-02-01

    Vision systems will play an increasing role in inteffigent material handling systems. This paper discusses two hardware principles which make possible a host of cost-effective applications--integrated vision systems and the use of retroreflective materials. Described are (1) the design cost and performance characteristics of integrated systems those with the microcomputer array detector and illumination as part of a single circuit (2) the impact of using retroreflective materials those with apparent brightness of more than 1000 times that of diffuse white surfaces and (3) some specific applications: AGV guidance part handling and AS/RS control.

  3. Options in Extraterrestrial Sample Handling and Study

    NASA Astrophysics Data System (ADS)

    Papanastassiou, Dimitri A.

    2000-10-01

    This presentation mentions important service functions such as: sample preservation, hazard assessment, and handling. It also discuss how preliminary examination of samples is necessary for sample hazard assessment and for sample allocations. Clean facilities and clean sample handling are required. Conflicts, cross contamination issues will be present and need to be resolved. Extensive experience is available for extraterrestrial samples and must be sought and applied. Extensive experience is available in studies of pathogenicity and must be sought and applied as necessary. Advisory and oversight structures must also be in place

  4. Options in Extraterrestrial Sample Handling and Study

    NASA Technical Reports Server (NTRS)

    Papanastassiou, Dimitri A.

    2000-01-01

    This presentation mentions important service functions such as: sample preservation, hazard assessment, and handling. It also discuss how preliminary examination of samples is necessary for sample hazard assessment and for sample allocations. Clean facilities and clean sample handling are required. Conflicts, cross contamination issues will be present and need to be resolved. Extensive experience is available for extraterrestrial samples and must be sought and applied. Extensive experience is available in studies of pathogenicity and must be sought and applied as necessary. Advisory and oversight structures must also be in place

  5. Structural interaction with transportation and handling systems

    NASA Technical Reports Server (NTRS)

    1973-01-01

    Problems involved in the handling and transportation of finished space vehicles from the factory to the launch site are presented, in addition to recommendations for properly accounting for in space vehicle structural design, adverse interactions during transportation. Emphasis is given to the protection of vehicle structures against those environments and loads encountered during transportation (including temporary storage) which would exceed the levels that the vehicle can safely withstand. Current practices for verifying vehicle safety are appraised, and some of the capabilities and limitations of transportation and handling systems are summarized.

  6. Planetary sample rapid recovery and handling

    NASA Technical Reports Server (NTRS)

    1985-01-01

    Methods for recovering and cost effectively handling planetary samples following return to the vicinity of Earth were designed for planetary mission planners. Three topics are addressed: (1) a rough cost estimate was produced for each of a series of options for the handling of planetary samples following their return to the vicinity of Earth; (2) the difficulty of quickly retrieving planetary samples from low circular and high elliptical Earth orbit is assessed; and (3) a conceptual design for a biological isolation and thermal control system for the returned sample and spacecraft is developed.

  7. Machine Shop Fundamentals: Part I.

    ERIC Educational Resources Information Center

    Kelly, Michael G.; And Others

    These instructional materials were developed and designed for secondary and adult limited English proficient students enrolled in machine tool technology courses. Part 1 includes 24 lessons covering introduction, safety and shop rules, basic machine tools, basic machine operations, measurement, basic blueprint reading, layout, and bench tools.…

  8. Hydraulic Fatigue-Testing Machine

    NASA Technical Reports Server (NTRS)

    Hodo, James D.; Moore, Dennis R.; Morris, Thomas F.; Tiller, Newton G.

    1987-01-01

    Fatigue-testing machine applies fluctuating tension to number of specimens at same time. When sample breaks, machine continues to test remaining specimens. Series of tensile tests needed to determine fatigue properties of materials performed more rapidly than in conventional fatigue-testing machine.

  9. Association installs condom machine.

    PubMed

    1994-08-01

    On the occasion of World Population Day (11 July), India installed its first condom vending machine. The machine was inaugurated by Mr. Eruch Lala, an official of the Family Planning Association of India, as part of the association's campaign to help the country curb its rapid population growth rate and stem the spread of AIDS (acquired immune deficiency syndrome). Each condom, called sangam ("union" in English) costs Rupees 2 (about 6.5 US cents). The machine is located at a textile mill in Bombay. The Association said it would install at least 60 such machines in Bombay over the coming months. "A psychological advantage of the machine is that the user need not personally meet the dispenser and can collect a condom without any embarrassment," Mr. Lala said. "The machine is expected to promote efforts at curbing population growth and prevent the spread of AIDS," he said. In a separate report, AIDS has been found to be racing through India just eight years after the first case was detected. Prostitutes, drug addicts and untested blood supplies are the conduits. More than half of the prostitutes in cities such as Bombay have HIV (human immunodeficiency virus), which causes AIDS. The truck drivers and itinerant workers they serve carry it to their own villages, according to the report by Mr. Thomas Wagner writing for the Associated Press. There are 43 million cases of sexually transmitted diseases reported each year in the country, according to the report. The HIV virus has been reported in all 25 states of India. Although the AIDS pandemic came to India later than most large countries, the National AIDS Control Organization estimates there are 1.62 million cases in the population, up 60% from 1993, according to the report. "AIDS is no longer just a problem of high-risk groups; it has spread to every area of India," Dr. P.R. Das Gupta of the national AIDS agency said in an interview. "So many people are migrating from their villages in search of jobs that this

  10. Prediction of Machine Tool Condition Using Support Vector Machine

    NASA Astrophysics Data System (ADS)

    Wang, Peigong; Meng, Qingfeng; Zhao, Jian; Li, Junjie; Wang, Xiufeng

    2011-07-01

    Condition monitoring and predicting of CNC machine tools are investigated in this paper. Considering the CNC machine tools are often small numbers of samples, a condition predicting method for CNC machine tools based on support vector machines (SVMs) is proposed, then one-step and multi-step condition prediction models are constructed. The support vector machines prediction models are used to predict the trends of working condition of a certain type of CNC worm wheel and gear grinding machine by applying sequence data of vibration signal, which is collected during machine processing. And the relationship between different eigenvalue in CNC vibration signal and machining quality is discussed. The test result shows that the trend of vibration signal Peak-to-peak value in surface normal direction is most relevant to the trend of surface roughness value. In trends prediction of working condition, support vector machine has higher prediction accuracy both in the short term ('One-step') and long term (multi-step) prediction compared to autoregressive (AR) model and the RBF neural network. Experimental results show that it is feasible to apply support vector machine to CNC machine tool condition prediction.

  11. Effect of Machining Velocity in Nanoscale Machining Operations

    NASA Astrophysics Data System (ADS)

    Islam, Sumaiya; Ibrahim, Raafat; Khondoker, Noman

    2015-04-01

    The aim of this study is to investigate the generated forces and deformations of single crystal Cu with (100), (110) and (111) crystallographic orientations at nanoscale machining operation. A nanoindenter equipped with nanoscratching attachment was used for machining operations and in-situ observation of a nano scale groove. As a machining parameter, the machining velocity was varied to measure the normal and cutting forces. At a fixed machining velocity, different levels of normal and cutting forces were generated due to different crystallographic orientations of the specimens. Moreover, after machining operation percentage of elastic recovery was measured and it was found that both the elastic and plastic deformations were responsible for producing a nano scale groove within the range of machining velocities from 250-1000 nm/s.

  12. Engineering molecular machines

    NASA Astrophysics Data System (ADS)

    Erman, Burak

    2016-04-01

    Biological molecular motors use chemical energy, mostly in the form of ATP hydrolysis, and convert it to mechanical energy. Correlated thermal fluctuations are essential for the function of a molecular machine and it is the hydrolysis of ATP that modifies the correlated fluctuations of the system. Correlations are consequences of the molecular architecture of the protein. The idea that synthetic molecular machines may be constructed by designing the proper molecular architecture is challenging. In their paper, Sarkar et al (2016 New J. Phys. 18 043006) propose a synthetic molecular motor based on the coarse grained elastic network model of proteins and show by numerical simulations that motor function is realized, ranging from deterministic to thermal, depending on temperature. This work opens up a new range of possibilities of molecular architecture based engine design.

  13. Wholly Synthetic Molecular Machines.

    PubMed

    Cheng, Chuyang; Stoddart, J Fraser

    2016-06-17

    The past quarter of a century has witnessed an increasing engagement on the part of physicists and chemists in the design and synthesis of molecular machines de novo. This minireview traces the development of artificial molecular machines from their prototypes in the form of shuttles and switches to their emergence as motors and pumps where supplies of energy in the form of chemical fuel, electrochemical potential and light activation become a minimum requirement for them to function away from equilibrium. The challenge facing this rapidly growing community of scientists and engineers today is one of putting wholly synthetic molecules to work, both individually and as collections. Here, we highlight some of the recent conceptual and practical advances relating to the operation of wholly synthetic rotary and linear motors.

  14. Machinations of thought

    SciTech Connect

    Waldrop, M.M.

    1985-03-01

    After three decades of frustrating work, artificial intelligence is coming of age--moving out of the laboratories and into the marketplace. Expert systems, computer programs that give advice like a human specialist, are pinpointing mineral deposits and diagnosing diseases. Programs are taking shape that can do a pretty fair job of understanding plain English or French. Robotics will soon benefit from computer vision systems able to store a digitized photograph of an object or scene and recognize a good bit of what is there. As the more exuberant enthusiasts see it, we might soon have machines to advise us about our income taxes or the baby's fever; silicon tutors could help a child master the enthralling possibilities of geometry and numbers; trucks might drive themselves through the night and unload themselves at their destination. In short, we could one day have machines to do almost anything that now requires intelligence in a human.

  15. Medical Dataset Classification: A Machine Learning Paradigm Integrating Particle Swarm Optimization with Extreme Learning Machine Classifier

    PubMed Central

    Subbulakshmi, C. V.; Deepa, S. N.

    2015-01-01

    Medical data classification is a prime data mining problem being discussed about for a decade that has attracted several researchers around the world. Most classifiers are designed so as to learn from the data itself using a training process, because complete expert knowledge to determine classifier parameters is impracticable. This paper proposes a hybrid methodology based on machine learning paradigm. This paradigm integrates the successful exploration mechanism called self-regulated learning capability of the particle swarm optimization (PSO) algorithm with the extreme learning machine (ELM) classifier. As a recent off-line learning method, ELM is a single-hidden layer feedforward neural network (FFNN), proved to be an excellent classifier with large number of hidden layer neurons. In this research, PSO is used to determine the optimum set of parameters for the ELM, thus reducing the number of hidden layer neurons, and it further improves the network generalization performance. The proposed method is experimented on five benchmarked datasets of the UCI Machine Learning Repository for handling medical dataset classification. Simulation results show that the proposed approach is able to achieve good generalization performance, compared to the results of other classifiers. PMID:26491713

  16. A Boltzmann machine for the organization of intelligent machines

    NASA Technical Reports Server (NTRS)

    Moed, Michael C.; Saridis, George N.

    1989-01-01

    In the present technological society, there is a major need to build machines that would execute intelligent tasks operating in uncertain environments with minimum interaction with a human operator. Although some designers have built smart robots, utilizing heuristic ideas, there is no systematic approach to design such machines in an engineering manner. Recently, cross-disciplinary research from the fields of computers, systems AI and information theory has served to set the foundations of the emerging area of the design of intelligent machines. Since 1977 Saridis has been developing an approach, defined as Hierarchical Intelligent Control, designed to organize, coordinate and execute anthropomorphic tasks by a machine with minimum interaction with a human operator. This approach utilizes analytical (probabilistic) models to describe and control the various functions of the intelligent machine structured by the intuitively defined principle of Increasing Precision with Decreasing Intelligence (IPDI) (Saridis 1979). This principle, even though resembles the managerial structure of organizational systems (Levis 1988), has been derived on an analytic basis by Saridis (1988). The purpose is to derive analytically a Boltzmann machine suitable for optimal connection of nodes in a neural net (Fahlman, Hinton, Sejnowski, 1985). Then this machine will serve to search for the optimal design of the organization level of an intelligent machine. In order to accomplish this, some mathematical theory of the intelligent machines will be first outlined. Then some definitions of the variables associated with the principle, like machine intelligence, machine knowledge, and precision will be made (Saridis, Valavanis 1988). Then a procedure to establish the Boltzmann machine on an analytic basis will be presented and illustrated by an example in designing the organization level of an Intelligent Machine. A new search technique, the Modified Genetic Algorithm, is presented and proved

  17. Machine Translation from Text

    NASA Astrophysics Data System (ADS)

    Habash, Nizar; Olive, Joseph; Christianson, Caitlin; McCary, John

    Machine translation (MT) from text, the topic of this chapter, is perhaps the heart of the GALE project. Beyond being a well defined application that stands on its own, MT from text is the link between the automatic speech recognition component and the distillation component. The focus of MT in GALE is on translating from Arabic or Chinese to English. The three languages represent a wide range of linguistic diversity and make the GALE MT task rather challenging and exciting.

  18. Copying Machine Improvement

    NASA Technical Reports Server (NTRS)

    1981-01-01

    Manufacturer of the Model 2210 copying machine was looking for a plastic valve bushing material that could be produced by a low-cost injection molding process to replace the unsuitable valve bushing they were using. NERAC conducted a computer search of the NASA database and was able to supply Nashua Corporation with several technical reports in their area of interest. Information aided the company's development of a urethane valve bushing which solved the problem and created a dramatic reduction in unit cost.

  19. Austempered Ductile Iron Machining

    NASA Astrophysics Data System (ADS)

    Pilc, Jozef; Šajgalík, Michal; Holubják, Jozef; Piešová, Marianna; Zaušková, Lucia; Babík, Ondrej; Kuždák, Viktor; Rákoci, Jozef

    2015-12-01

    This article deals with the machining of cast iron. In industrial practice, Austempered Ductile Iron began to be used relatively recently. ADI is ductile iron that has gone through austempering to get improved properties, among which we can include strength, wear resistance or noise damping. This specific material is defined also by other properties, such as high elasticity, ductility and endurance against tenigue, which are the properties, that considerably make the tooling characteristic worse.

  20. Machine Learning in Medicine.

    PubMed

    Deo, Rahul C

    2015-11-17

    Spurred by advances in processing power, memory, storage, and an unprecedented wealth of data, computers are being asked to tackle increasingly complex learning tasks, often with astonishing success. Computers have now mastered a popular variant of poker, learned the laws of physics from experimental data, and become experts in video games - tasks that would have been deemed impossible not too long ago. In parallel, the number of companies centered on applying complex data analysis to varying industries has exploded, and it is thus unsurprising that some analytic companies are turning attention to problems in health care. The purpose of this review is to explore what problems in medicine might benefit from such learning approaches and use examples from the literature to introduce basic concepts in machine learning. It is important to note that seemingly large enough medical data sets and adequate learning algorithms have been available for many decades, and yet, although there are thousands of papers applying machine learning algorithms to medical data, very few have contributed meaningfully to clinical care. This lack of impact stands in stark contrast to the enormous relevance of machine learning to many other industries. Thus, part of my effort will be to identify what obstacles there may be to changing the practice of medicine through statistical learning approaches, and discuss how these might be overcome. PMID:26572668

  1. Machine Learning in Medicine.

    PubMed

    Deo, Rahul C

    2015-11-17

    Spurred by advances in processing power, memory, storage, and an unprecedented wealth of data, computers are being asked to tackle increasingly complex learning tasks, often with astonishing success. Computers have now mastered a popular variant of poker, learned the laws of physics from experimental data, and become experts in video games - tasks that would have been deemed impossible not too long ago. In parallel, the number of companies centered on applying complex data analysis to varying industries has exploded, and it is thus unsurprising that some analytic companies are turning attention to problems in health care. The purpose of this review is to explore what problems in medicine might benefit from such learning approaches and use examples from the literature to introduce basic concepts in machine learning. It is important to note that seemingly large enough medical data sets and adequate learning algorithms have been available for many decades, and yet, although there are thousands of papers applying machine learning algorithms to medical data, very few have contributed meaningfully to clinical care. This lack of impact stands in stark contrast to the enormous relevance of machine learning to many other industries. Thus, part of my effort will be to identify what obstacles there may be to changing the practice of medicine through statistical learning approaches, and discuss how these might be overcome.

  2. Architectures for intelligent machines

    NASA Technical Reports Server (NTRS)

    Saridis, George N.

    1991-01-01

    The theory of intelligent machines has been recently reformulated to incorporate new architectures that are using neural and Petri nets. The analytic functions of an intelligent machine are implemented by intelligent controls, using entropy as a measure. The resulting hierarchical control structure is based on the principle of increasing precision with decreasing intelligence. Each of the three levels of the intelligent control is using different architectures, in order to satisfy the requirements of the principle: the organization level is moduled after a Boltzmann machine for abstract reasoning, task planning and decision making; the coordination level is composed of a number of Petri net transducers supervised, for command exchange, by a dispatcher, which also serves as an interface to the organization level; the execution level, include the sensory, planning for navigation and control hardware which interacts one-to-one with the appropriate coordinators, while a VME bus provides a channel for database exchange among the several devices. This system is currently implemented on a robotic transporter, designed for space construction at the CIRSSE laboratories at the Rensselaer Polytechnic Institute. The progress of its development is reported.

  3. Laser machining - Theory and practice

    SciTech Connect

    Chryssolouris, G.

    1991-01-01

    Recent developments and the state of the art in the field of laser machining are reviewed with emphasis on practical applications. First, an overview of conventional material removing processes is presented. Laser machining systems are then described, and an overview is provided of the necessary knowledge from heat transfer and fluid mechanics required in order to understand the physical mechanisms and thermal processes associated with laser machining. The applications of laser machining discussed include drilling, cutting, marking, and three-dimensional machining of metals, ceramics, plastics, composites, and other materials, and micromachining. 209 refs.

  4. 7 CFR 948.8 - Handle or ship.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport,...

  5. 7 CFR 927.8 - Ship or handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any...

  6. 7 CFR 945.9 - Ship or handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to...

  7. 7 CFR 927.8 - Ship or handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any...

  8. 7 CFR 948.8 - Handle or ship.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport,...

  9. 7 CFR 927.8 - Ship or handle.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any...

  10. 7 CFR 945.9 - Ship or handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to...

  11. 7 CFR 927.8 - Ship or handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any...

  12. 7 CFR 948.8 - Handle or ship.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport,...

  13. 7 CFR 948.8 - Handle or ship.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport,...

  14. 7 CFR 945.9 - Ship or handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to...

  15. 7 CFR 927.8 - Ship or handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any...

  16. 7 CFR 948.8 - Handle or ship.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport,...

  17. Information Handling in the Life Sciences.

    ERIC Educational Resources Information Center

    Steere, William C., Ed.

    Special problems in the handling of biological information arise from the diversity of biological subject matter and the complexity of biological approaches towards phenomena of the living world. This state-of-the-art report on communications of information in the biological sciences provides information on: (1) users of biological information,…

  18. 9 CFR 3.41 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Pigs and Hamsters Transportation Standards § 3.41 Handling. (a) Any person who is subject to the Animal Welfare regulations and who moves live guinea pigs or hamsters from an animal holding area of a terminal... person subject to the Animal Welfare Act and holding any live guinea pig or hamster in an animal...

  19. 9 CFR 3.41 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Pigs and Hamsters Transportation Standards § 3.41 Handling. (a) Any person who is subject to the Animal Welfare regulations and who moves live guinea pigs or hamsters from an animal holding area of a terminal... person subject to the Animal Welfare Act and holding any live guinea pig or hamster in an animal...

  20. Lifting and handling. Strategies for altering practice.

    PubMed

    Hack, L; Potter, S

    The elderly services directorate at the Ipswich Hospital NHS Trust has already embarked on changing nurses' patient-handling practice in response to EC regulations. This paper describes how problems hindered the programme's initial success and explores how new strategies have been implemented to overcome them.

  1. Teaching Package on Standardisation in Information Handling.

    ERIC Educational Resources Information Center

    United Nations Educational, Scientific and Cultural Organization, Paris (France). General Information Programme.

    One of the objectives of the United Nations Educational, Scientific, and Cultural Organization (UNESCO) is to promote standardization in the field of information handling, both in development of guidelines and standards and in the use and application of existing norms and standards. This teaching package on the standardization of information…

  2. 9 CFR 3.19 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Cats 1 Transportation Standards § 3.19 Handling. (a) Any person subject to the Animal Welfare regulations (9 CFR parts 1, 2, and 3) who moves (including loading and unloading) dogs or cats within, to, or... efficiently as possible and must provide the following during movement of the dog or cat: (1) Shelter...

  3. 7 CFR 930.10 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Handle. 930.10 Section 930.10 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE TART CHERRIES GROWN IN THE STATES OF MICHIGAN, NEW YORK, PENNSYLVANIA, OREGON,...

  4. 9 CFR 3.92 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Primates 2 Transportation Standards § 3.92 Handling. (a) Any person subject to the Animal Welfare regulations (9 CFR parts 1, 2, and 3) who moves (including loading and unloading) nonhuman primates within, to... and efficiently as possible, and must provide the following during movement of the nonhuman...

  5. 9 CFR 3.92 - Handling.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Primates 2 Transportation Standards § 3.92 Handling. (a) Any person subject to the Animal Welfare regulations (9 CFR parts 1, 2, and 3) who moves (including loading and unloading) nonhuman primates within, to... and efficiently as possible, and must provide the following during movement of the nonhuman...

  6. 9 CFR 3.92 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Primates 2 Transportation Standards § 3.92 Handling. (a) Any person subject to the Animal Welfare regulations (9 CFR parts 1, 2, and 3) who moves (including loading and unloading) nonhuman primates within, to... and efficiently as possible, and must provide the following during movement of the nonhuman...

  7. 9 CFR 3.41 - Handling.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... Pigs and Hamsters Transportation Standards § 3.41 Handling. (a) Any person who is subject to the Animal Welfare regulations and who moves live guinea pigs or hamsters from an animal holding area of a terminal... person subject to the Animal Welfare Act and holding any live guinea pig or hamster in an animal...

  8. 9 CFR 3.41 - Handling.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... Pigs and Hamsters Transportation Standards § 3.41 Handling. (a) Any person who is subject to the Animal Welfare regulations and who moves live guinea pigs or hamsters from an animal holding area of a terminal... person subject to the Animal Welfare Act and holding any live guinea pig or hamster in an animal...

  9. 9 CFR 3.41 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... Pigs and Hamsters Transportation Standards § 3.41 Handling. (a) Any person who is subject to the Animal Welfare regulations and who moves live guinea pigs or hamsters from an animal holding area of a terminal... person subject to the Animal Welfare Act and holding any live guinea pig or hamster in an animal...

  10. 7 CFR 930.10 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... MICHIGAN, NEW YORK, PENNSYLVANIA, OREGON, UTAH, WASHINGTON, AND WISCONSIN Order Regulating Handling... processed product for home use and not for resale. (b) The transportation within the production area of... or transportation of cherries by a grower to a handler of record within the production area. (e)...

  11. 340 waste handling facility interim safety basis

    SciTech Connect

    VAIL, T.S.

    1999-04-01

    This document presents an interim safety basis for the 340 Waste Handling Facility classifying the 340 Facility as a Hazard Category 3 facility. The hazard analysis quantifies the operating safety envelop for this facility and demonstrates that the facility can be operated without a significant threat to onsite or offsite people.

  12. Success Counseling: How to Handle Discipline Problems.

    ERIC Educational Resources Information Center

    Boffey, D. Barnes; Boffey, David M.

    1994-01-01

    This second article of a two-part series describes how success counseling techniques can be used to handle discipline problems by helping campers to accept personal responsibility and develop effective problem-solving skills. Instead of using punishment, success counseling techniques enable campers to recognize what they want, identify appropriate…

  13. 340 Waste handling facility interim safety basis

    SciTech Connect

    Stordeur, R.T.

    1996-10-04

    This document presents an interim safety basis for the 340 Waste Handling Facility classifying the 340 Facility as a Hazard Category 3 facility. The hazard analysis quantifies the operating safety envelop for this facility and demonstrates that the facility can be operated without a significant threat to onsite or offsite people.

  14. Handling qualities effects of display latency

    NASA Technical Reports Server (NTRS)

    King, David W.

    1993-01-01

    Display latency is the time delay between aircraft response and the corresponding response of the cockpit displays. Currently, there is no explicit specification for allowable display lags to ensure acceptable aircraft handling qualities in instrument flight conditions. This paper examines the handling qualities effects of display latency between 70 and 400 milliseconds for precision instrument flight tasks of the V-22 Tiltrotor aircraft. Display delay effects on the pilot control loop are analytically predicted through a second order pilot crossover model of the V-22 lateral axis, and handling qualities trends are evaluated through a series of fixed-base piloted simulation tests. The results show that the effects of display latency for flight path tracking tasks are driven by the stability characteristics of the attitude control loop. The data indicate that the loss of control damping due to latency can be simply predicted from knowledge of the aircraft's stability margins, control system lags, and required control bandwidths. Based on the relationship between attitude control damping and handling qualities ratings, latency design guidelines are presented. In addition, this paper presents a design philosophy, supported by simulation data, for using flight director display augmentation to suppress the effects of display latency for delays up to 300 milliseconds.

  15. Data Handling Problems in Cell Biology.

    ERIC Educational Resources Information Center

    Dawson, M. M.; Kumar, P.; Smith, C. A.

    1997-01-01

    Offers examples of problems that assess student ability to recall, handle, manipulate, and interpret data and also reinforce basic knowledge of cell biology. The questions, purposely designed for first-year students, complement formal lectures and practical classes given in the subject. Illustrates the range and types of material which cell…

  16. 7 CFR 1212.8 - Handle.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ..., PROMOTION, CONSUMER EDUCATION AND INDUSTRY INFORMATION ORDER Honey Packers and Importers Research, Promotion, Consumer Education, and Industry Information Order Definitions § 1212.8 Handle. “Handle” means to process, package, sell, transport, purchase or in any other way place honey or honey products, or causes them to...

  17. 9 CFR 3.66 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment and Transportation of Rabbits... moves live rabbits from an animal holding area of a terminal facility to a primary conveyance or vice... regulations and holding any live rabbit in an animal holding area of a terminal facility or transporting...

  18. Facing the Limitations of Electronic Document Handling.

    ERIC Educational Resources Information Center

    Moralee, Dennis

    1985-01-01

    This essay addresses problems associated with technology used in the handling of high-resolution visual images in electronic document delivery. Highlights include visual fidelity, laser-driven optical disk storage, electronics versus micrographics for document storage, videomicrographics, and system configurations and peripherals. (EJS)

  19. Intertextuality for Handling Complex Environmental Issues

    ERIC Educational Resources Information Center

    Byhring, Anne Kristine; Knain, Erik

    2016-01-01

    Nowhere is the need for handling complexity more pertinent than in addressing environmental issues. Our study explores students' situated constructs of complexity in unfolding discourses on socio-scientific issues. Students' dialogues in two group-work episodes are analysed in detail, with tools from Systemic Functional Linguistics. We identify…

  20. Math Model for Naval Ship Handling Trainer.

    ERIC Educational Resources Information Center

    Golovcsenko, Igor V.

    The report describes the math model for an experimental ship handling trainer. The training task is that of a replenishment operation at sea. The model includes equations for ship dynamics of a destroyer, propeller-engine response times, ship separation, interaction effects between supply ship and destroyer, and outputs to a visual display system.…

  1. Guidance Counsellor Strategies for Handling Bullying

    ERIC Educational Resources Information Center

    Power-Elliott, Michleen; Harris, Gregory E.

    2012-01-01

    The purpose of this exploratory-descriptive study was to examine how guidance counsellors in the province of Newfoundland and Labrador would handle a specific verbal-relational bullying incident. Also of interest was guidance counsellor involvement and training in bullying programmes and Positive Behaviour Supports. Data for this study was…

  2. 7 CFR 917.6 - Handle.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Handle. 917.6 Section 917.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN...

  3. 7 CFR 917.6 - Handle.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Handle. 917.6 Section 917.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN...

  4. 7 CFR 917.6 - Handle.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Handle. 917.6 Section 917.6 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE FRESH PEARS AND PEACHES GROWN IN...

  5. 7 CFR 948.386 - Handling regulation.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... inspection certificate has been issued with respect thereto and the certificate is valid at the time of... made available for examination at any time upon request. (3) Each handler who handles potatoes after... shall not be applicable to shipments of potatoes for: (i) Livestock feed; (ii) Relief or charity;...

  6. 9 CFR 3.19 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... regulations (9 CFR parts 1, 2, and 3) who moves (including loading and unloading) dogs or cats within, to, or... WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Dogs and... efficiently as possible and must provide the following during movement of the dog or cat: (1) Shelter...

  7. 50 CFR 14.111 - Handling.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ... 50 Wildlife and Fisheries 1 2013-10-01 2013-10-01 false Handling. 14.111 Section 14.111 Wildlife and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION, TRANSPORTATION, SALE, PURCHASE, BARTER, EXPORTATION, AND IMPORTATION OF WILDLIFE AND PLANTS IMPORTATION, EXPORTATION, AND TRANSPORTATION OF...

  8. 9 CFR 3.118 - Handling.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL... mammals from the animal holding area of the terminal facility to the primary conveyance or from...

  9. 9 CFR 3.118 - Handling.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL... mammals from the animal holding area of the terminal facility to the primary conveyance or from...

  10. 9 CFR 3.118 - Handling.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL... mammals from the animal holding area of the terminal facility to the primary conveyance or from...

  11. Solar panel handling and mounting device

    SciTech Connect

    Diba, K.T.

    1985-02-12

    The device is formed with flanges at right angles to each other which can engage the edge and side of a solar panel and be secured thereto. The device has a handgrip thereon for manual handling of the solar panel during transportation and installation. The device has openings therein for securing the solar panel in place during transportation and at installation.

  12. Flexible Phrase Based Query Handling Algorithms.

    ERIC Educational Resources Information Center

    Wilbur, W. John; Kim, Won

    2001-01-01

    Flexibility in query handling can be important if one types a search engine query that is misspelled, contains terms not in the database, or requires knowledge of a controlled vocabulary. Presents results of experiments that suggest the optimal form of similarity functions that are applicable to the task of phrase based retrieval to find either…

  13. 46 CFR 111.106-13 - Cargo handling devices or cargo pump rooms handling flammable or combustible cargoes.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ... 46 Shipping 4 2014-10-01 2014-10-01 false Cargo handling devices or cargo pump rooms handling... OSVs § 111.106-13 Cargo handling devices or cargo pump rooms handling flammable or combustible cargoes... classification of such areas. (c) Cargo pump rooms must be isolated from all sources of vapor ignition...

  14. Design and evaluation of an optical disk handling tool for a cleanroom environment.

    PubMed

    Vora, P V; Reynolds, J L; Corl, K G

    1992-12-01

    In this paper, we present an application of engineering and ergonomics principles in the design of an optical disk handling tool for use in a cleanroom environment. A qualitative model which considers the task, operator, machines and environment (TOME model) was utilized to guide the design process. A 'before-after' evaluation found a significant improvement in the proposed tool over the existing tool with respect to mechanical, biomechanical and subjective measures. Product yield has improved considerably, as measured after the implementation of the proposed tool in December 1989 until the end of the observation period in June 1991.

  15. 15. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    15. Interior, Machine Shop, Roundhouse Machine Shop Extension, Southern Pacific Railroad Carlin Shops, view to northeast (90mm lens). The arched cutouts in the bottom chords of the roof trusses were necessary to provide clearance for the smokestacks of steam locomotives, and also mark the location of the former inspection pit in the floor (now filled in and covered by a new concrete floor). - Southern Pacific Railroad, Carlin Shops, Roundhouse Machine Shop Extension, Foot of Sixth Street, Carlin, Elko County, NV

  16. Diamond Measuring Machine

    SciTech Connect

    Krstulic, J.F.

    2000-01-27

    The fundamental goal of this project was to develop additional capabilities to the diamond measuring prototype, work out technical difficulties associated with the original device, and perform automated measurements which are accurate and repeatable. For this project, FM and T was responsible for the overall system design, edge extraction, and defect extraction and identification. AccuGem provided a lab and computer equipment in Lawrence, 3D modeling, industry expertise, and sets of diamonds for testing. The system executive software which controls stone positioning, lighting, focusing, report generation, and data acquisition was written in Microsoft Visual Basic 6, while data analysis and modeling were compiled in C/C++ DLLs. All scanning parameters and extracted data are stored in a central database and available for automated analysis and reporting. The Phase 1 study showed that data can be extracted and measured from diamond scans, but most of the information had to be manually extracted. In this Phase 2 project, all data required for geometric modeling and defect identification were automatically extracted and passed to a 3D modeling module for analysis. Algorithms were developed which automatically adjusted both light levels and stone focus positioning for each diamond-under-test. After a diamond is analyzed and measurements are completed, a report is printed for the customer which shows carat weight, summarizes stone geometry information, lists defects and their size, displays a picture of the diamond, and shows a plot of defects on a top view drawing of the stone. Initial emphasis of defect extraction was on identification of feathers, pinpoints, and crystals. Defects were plotted color-coded by industry standards for inclusions (red), blemishes (green), and unknown defects (blue). Diamonds with a wide variety of cut quality, size, and number of defects were tested in the machine. Edge extraction, defect extraction, and modeling code were tested for

  17. Will machines ever think

    NASA Technical Reports Server (NTRS)

    Denning, P. J.

    1986-01-01

    Artificial Intelligence research has come under fire for failing to fulfill its promises. A growing number of AI researchers are reexamining the bases of AI research and are challenging the assumption that intelligent behavior can be fully explained as manipulation of symbols by algorithms. Three recent books -- Mind over Machine (H. Dreyfus and S. Dreyfus), Understanding Computers and Cognition (T. Winograd and F. Flores), and Brains, Behavior, and Robots (J. Albus) -- explore alternatives and open the door to new architectures that may be able to learn skills.

  18. CENTRIFUGAL CASTING MACHINE

    DOEpatents

    Shuck, A.B.

    1958-04-01

    A device is described that is specifically designed to cast uraniumn fuel rods in a vacuunn, in order to obtain flawless, nonoxidized castings which subsequently require a maximum of machining or wastage of the expensive processed material. A chamber surrounded with heating elements is connected to the molds, and the entire apparatus is housed in an airtight container. A charge of uranium is placed in the chamber, heated, then is allowed to flow into the molds While being rotated. Water circulating through passages in the molds chills the casting to form a fine grained fuel rod in nearly finished form.

  19. Space shuttle data handling and communications considerations.

    NASA Technical Reports Server (NTRS)

    Stoker, C. J.; Minor, R. G.

    1971-01-01

    Operational and development flight instrumentation, data handling subsystems and communication requirements of the space shuttle orbiter are discussed. Emphasis is made on data gathering methods, crew display data, computer processing, recording, and telemetry by means of a digital data bus. Also considered are overall communication conceptual system aspects and design features allowing a proper specification of telemetry encoders and instrumentation recorders. An adaptive bit rate concept is proposed to handle the telemetry bit rates which vary with the amount of operational and experimental data to be transmitted. A split-phase encoding technique is proposed for telemetry to cope with the excessive bit jitter and low bit transition density which may affect television performance.

  20. Development of liquid handling techniques in microgravity

    NASA Technical Reports Server (NTRS)

    Antar, Basil N.

    1995-01-01

    A large number of experiments dealing with protein crystal growth and also with growth of crystals from solution require complicated fluid handling procedures including filling of empty containers with liquids, mixing of solutions, and stirring of liquids. Such procedures are accomplished in a straight forward manner when performed under terrestrial conditions in the laboratory. However, in the low gravity environment of space, such as on board the Space Shuttle or an Earth-orbiting space station, these procedures sometimes produced entirely undesirable results. Under terrestrial conditions, liquids usually completely separate from the gas due to the buoyancy effects of Earth's gravity. Consequently, any gas pockets that are entrained into the liquid during a fluid handling procedure will eventually migrate towards the top of the vessel where they can be removed. In a low gravity environment any folded gas bubble will remain within the liquid bulk indefinitely at a location that is not known a priori resulting in a mixture of liquid and vapor.

  1. Waste handling activities in glovebox dismantling facility

    SciTech Connect

    Kitamura, Akihiro; Okada, Takashi; Kashiro, Kashio; Yoshino, Masanori; Hirano, Hiroshi

    2007-07-01

    The Glovebox Dismantling Facility is a facility to decontaminate and size-reduce after-service gloveboxes in the Plutonium Fuel Production Facility, Nuclear Fuel Cycle Engineering Laboratories, Japan Atomic Energy Agency. The wastes generated from these dismantling activities are simultaneously handled and packaged into drums in a bag-out manner. For future waste treatment and disposal, these wastes are separated into material categories. In this paper, we present the basic steps and analyzed data for the waste handling activities. The data were collected from dismantling activities for three gloveboxes (Grinding Pellet Glovebox, Visual Inspection Glovebox, Outer-diameter Screening Glovebox) conducted from 2001-2004. We also describe both current and near-future improvements. (authors)

  2. Acoustophoretic contactless transport and handling of matter

    NASA Astrophysics Data System (ADS)

    Foresti, Daniele; Nabavi, Majid; Klingauf, Mirko; Ferrari, Aldo; Poulikakos, Dimos

    2013-11-01

    Levitation and controlled motion of matter in air, has a wealth of potential applications ranging from materials processing to biochemistry and pharmaceuticals. We present a novel acoustophoretic concept, for the contactless transport and handling of matter in air. Spatiotemporal modulation of the levitation acoustic field allows continuous planar transport and processing of multiple objects (volume 0.1-10 μl) . The independence of the handling principle from special material properties (magnetic, optical or electrical) is illustrated with a wide palette of application experiments, such as contactless droplet coalescence and mixing, solid-liquid encapsulation, absorption, dissolution, and DNA transfection. The dynamics of droplets and particles collision is studied numerically and experimentally. The findings show that the secondary acoustic force gives a significant contribution to the samples impact velocity. We thank the Swiss National Science Foundation (Grant 144397) for financial support.

  3. A guide to forest seed handling

    SciTech Connect

    Willan, R.L.

    1986-01-01

    This guide to forest seed handling focuses on seed quality, i.e., the physiological viability and vigor of the seeds. Seed and fruit development, germination, and dormancy and the fundamentals of planning seed collections are covered. The guide includes discussions on seed collection of fallen fruits or seeds from the forest floor from the crowns of felled trees, and from standing trees with access from the ground and with other means of access. Also considered are precautions to be followed during fruit and seed handling between collection and processing. The different stages in seed processing are detailed, including extraction, depulping, drying, tumbling and threshing, dewinging, cleaning, grading, and mixing. Factors affecting seed longevity in storage and the choice of storage methods are reviewed. Different forms of seed pretreatment and seed testing methods are described.

  4. Alkali Metal Handling Practices at NASA MSFC

    NASA Technical Reports Server (NTRS)

    Salvail, Patrick G.; Carter, Robert R.

    2002-01-01

    NASA Marshall Space Flight Center (MSFC) is NASA s principle propulsion development center. Research and development is coordinated and carried out on not only the existing transportation systems, but also those that may be flown in the near future. Heat pipe cooled fast fission cores are among several concepts being considered for the Nuclear Systems Initiative. Marshall Space Flight Center has developed a capability to handle high-purity alkali metals for use in heat pipes or liquid metal heat transfer loops. This capability is a low budget prototype of an alkali metal handling system that would allow the production of flight qualified heat pipe modules or alkali metal loops. The processing approach used to introduce pure alkali metal into heat pipe modules and other test articles are described in this paper.

  5. Mars Sample Handling Protocol Workshop Series

    NASA Technical Reports Server (NTRS)

    Rummel, John D. (Editor); Race, Margaret S. (Editor); Acevedo, Sara (Technical Monitor)

    2000-01-01

    This document is the report resulting from the first workshop of the series on development of the criteria for a Mars sample handling protocol. Workshop 1 was held in Bethesda, Maryland on March 20-22, 2000. This report serves to document the proceedings of Workshop 1; it summarizes relevant background information, provides an overview of the deliberations to date, and helps frame issues that will need further attention or resolution in upcoming workshops. Specific recommendations are not part of this report.

  6. Fuel handling apparatus for a nuclear reactor

    DOEpatents

    Hawke, Basil C.

    1987-01-01

    Fuel handling apparatus for transporting fuel elements into and out of a nuclear reactor and transporting them within the reactor vessel extends through a penetration in the side of the reactor vessel. A lateral transport device carries the fuel elements laterally within the vessel and through the opening in the side of the vessel, and a reversible lifting device raises and lowers the fuel elements. In the preferred embodiment, the lifting device is supported by a pair of pivot arms.

  7. Handling System for Iridium-192 Seeds

    NASA Technical Reports Server (NTRS)

    Carpenter, W.; Wodicka, D.

    1973-01-01

    A complete system is proposed for safe handling of iridium-192 seeds used to internally irradiate malignant growths. A vibratory hopper feeds the seeds onto a transport system for deposit in a magazine or storage area. A circular magazine consisting of segmented plastic tubing with holes in the walls to accommodate the seeds seems feasible. The magazine is indexed to stop and release a seed for calibration and deposition.

  8. Powder handling for automated fuel processing

    SciTech Connect

    Frederickson, J.R.; Eschenbaum, R.C.; Goldmann, L.H.

    1989-04-09

    Installation of the Secure Automated Fabrication (SAF) line has been completed. It is located in the Fuel Cycle Plant (FCP) at the Department of Energy's (DOE) Hanford site near Richland, Washington. The SAF line was designed to fabricate advanced reactor fuel pellets and assemble fuel pins by automated, remote operation. This paper describes powder handling equipment and techniques utilized for automated powder processing and powder conditioning systems in this line. 9 figs.

  9. Pharmacology of myocardial calcium-handling.

    PubMed

    Vogler, Julia; Eckardt, Lars

    2012-07-01

    Disturbed myocardial calcium (Ca(+)) handling is one of the pathophysiologic hallmarks of cardiovascular diseases such as congestive heart failure, cardiac hypertrophy, and certain types of tachyarrhythmias. Pharmacologic treatment of these diseases thus focuses on restoring myocardial Ca(2+) homeostasis by interacting with Ca(2+)-dependent signaling pathways. In this article, we review the currently used pharmacologic agents that are able to restore or maintain myocardial Ca(2+) homeostasis and their mechanism of action as well as emerging new substances.

  10. Reactions and interactions in handling anticancer drugs.

    PubMed

    D'Arcy, P F

    1983-01-01

    The clinical toxicity of anticancer drugs has been well documented with regard to the adverse effects of treatment in patients. However, many of these drugs have a direct irritant effect on the skin, eyes, mucous membranes, and other tissues. Handled without due care, especially when being prepared for injection, most cytotoxic drugs can cause local toxic or allergic reactions; they also present hazards of carcinogenicity and mutagenicity. This spectrum of potential risk should be kept in mind by personnel administering or handling these drugs, especially in oncology units where just a few individuals may routinely and frequently reconstitute many doses of cytotoxic agents. This is work in which the hospital pharmacist should and must be involved; indeed, many of the techniques and skills required are identical with those used in standard aseptic procedures for preparing pharmaceutical products. Pharmacy departments should take the initiative in making hospital staff aware of the potential risks of handling neoplastic agents, and they should spearhead a multidisciplinary assessment for producing local guidelines for working with these drugs. This article warns practitioners about the inherent dangers of these practitioner-drug interactions and suggests ways in which they may be reduced. Information is given in tabular form regarding recommended procedures for reconstituting 24 anticancer drugs and precautions to protect the personnel handling them, especially when there is spillage of powdered or liquid drugs. Also, guidelines are given about incompatibilities with admixtures of such drugs, and the literature is reviewed relative to recent developments in hospital pharmacy departments where reconstitution of anticancer drugs has been incorporated into existing intravenous fluid preparation/admixture units. Not only has this been shown to be safer and more effective in terms of time and labor, but also it has cut the cost of injectable cytotoxic drugs by an

  11. Formal modeling of virtual machines

    NASA Technical Reports Server (NTRS)

    Cremers, A. B.; Hibbard, T. N.

    1978-01-01

    Systematic software design can be based on the development of a 'hierarchy of virtual machines', each representing a 'level of abstraction' of the design process. The reported investigation presents the concept of 'data space' as a formal model for virtual machines. The presented model of a data space combines the notions of data type and mathematical machine to express the close interaction between data and control structures which takes place in a virtual machine. One of the main objectives of the investigation is to show that control-independent data type implementation is only of limited usefulness as an isolated tool of program development, and that the representation of data is generally dictated by the control context of a virtual machine. As a second objective, a better understanding is to be developed of virtual machine state structures than was heretofore provided by the view of the state space as a Cartesian product.

  12. D0 data handling operational experience

    SciTech Connect

    Lee Lueking et al.

    2003-08-11

    We report on the production experience of the D0 experiment at the Fermilab Tevatron, using the SAM data handling system with a variety of computing hardware configurations, batch systems, and mass storage strategies. We have stored more than 300 TB of data in the Fermilab Enstore mass storage system. We deliver data through this system at an average rate of more than 2 TB/day to analysis programs, with a substantial multiplication factor in the consumed data through intelligent cache management. We handle more than 1.7 Million files in this system and provide data delivery to user jobs at Fermilab on four types of systems: a reconstruction farm, a large SMP system, a Linux batch cluster, and a Linux desktop cluster. In addition, we import simulation data generated at 6 sites worldwide, and deliver data to jobs at many more sites. We describe the scope of the data handling deployment worldwide, the operational experience with this system, and the feedback of that experience.

  13. An Investigation of Large Aircraft Handling Qualities

    NASA Astrophysics Data System (ADS)

    Joyce, Richard D.

    An analytical technique for investigating transport aircraft handling qualities is exercised in a study using models of two such vehicles, a Boeing 747 and Lockheed C-5A. Two flight conditions are employed for climb and directional tasks, and a third included for a flare task. The analysis technique is based upon a "structural model" of the human pilot developed by Hess. The associated analysis procedure has been discussed previously in the literature, but centered almost exclusively on the characteristics of high-performance fighter aircraft. The handling qualities rating level (HQRL) and pilot induced oscillation tendencies rating level (PIORL) are predicted for nominal configurations of the aircraft and for "damaged" configurations where actuator rate limits are introduced as nonlinearites. It is demonstrated that the analysis can accommodate nonlinear pilot/vehicle behavior and do so in the context of specific flight tasks, yielding estimates of handling qualities, pilot-induced oscillation tendencies and upper limits of task performance. A brief human-in-the-loop tracking study was performed to provide a limited validation of the pilot model employed.

  14. Vestibule and Cask Preparation Mechanical Handling Calculation

    SciTech Connect

    N. Ambre

    2004-05-26

    The scope of this document is to develop the size, operational envelopes, and major requirements of the equipment to be used in the vestibule, cask preparation area, and the crane maintenance area of the Fuel Handling Facility. This calculation is intended to support the License Application (LA) submittal of December 2004, in accordance with the directive given by DOE correspondence received on the 27th of January 2004 entitled: ''Authorization for Bechtel SAIC Company L.L.C. to Include a Bare Fuel Handling Facility and Increased Aging Capacity in the License Application, Contract Number DE-AC28-01R W12101'' (Ref. 167124). This correspondence was appended by further correspondence received on the 19th of February 2004 entitled: ''Technical Direction to Bechtel SAIC Company L.L. C. for Surface Facility Improvements, Contract Number DE-AC28-01R W12101; TDL No. 04-024'' (Ref. 16875 1). These documents give the authorization for a Fuel Handling Facility to be included in the baseline. The limitations of this preliminary calculation lie within the assumptions of section 5 , as this calculation is part of an evolutionary design process.

  15. Smart Test Machines

    NASA Technical Reports Server (NTRS)

    1997-01-01

    Vern Wedeven, president of Wedeven Associates, developed the WAM4, a computer-aided "smart" test machine for simulating stress on equipment, based on his bearing lubrication expertise gained while working for Lewis Research Center. During his NASA years from the 1970s into the early 1980s, Wedeven initiated an "Interdisciplinary Collaboration in Tribology," an effort that involved NASA, six universities, and several university professors. The NASA-sponsored work provided foundation for Wedeven in 1983 to form his own company. Several versions of the smart test machine, the WAM1, WAM2, and WAM3, have proceeded the current version, WAM4. This computer-controlled device can provide detailed glimpses at gear and bearing points of contact. WAM4 can yield a three-dimensional view of machinery as an operator adds "what-if" thermal and lubrication conditions, contact stress, and surface motion. Along with NASA, a number of firms, including Pratt & Whitney, Caterpillar Tractor, Exxon, and Chevron have approached Wedeven for help on resolving lubrication problems.

  16. Neural network machine vision

    SciTech Connect

    Fox, R.O.; Czerniejewski, F.; Fluet, F.; Mitchell, E.

    1988-09-01

    Gould, Inc. and Nestor, Inc. cooperated on a joint development project to combine machine vision technology with neural network technology. The result is a machine vision system which can be trained by an inexperienced operator to perform qualitative classification. The hardware preprocessor reduces the information in the 2D camera image from 122,880 (i.e. 512 x 240) bytes to several hundred bytes in 64 milliseconds. The output of the preprocessor, which is in the format of connected lines, is fed to the first neural network. This neural network performs feature recognition. The output of the first neural network is a probability map. This map is fed to the input of the second neural network which performs object verification. The output of the second neural network is the object location and classification in the field of view. This information can optionally be fed into a third neural network which analyzes spatial relationships of objects in the field of view. The final output is a classification, by quality level, or by style. The system has been tested on applications ranging from the grading of plywood and the grading of paper to the sorting of fabricated metal parts. Specific application examples are presented.

  17. Large Surface Measuring Machine

    NASA Astrophysics Data System (ADS)

    Egdall, Mark; Breidenthal, Robert S.

    1983-09-01

    A new surface measuring concept developed under government contract at Itek Optical Systems has been previously reported by Allen Greenleaf. The method uses four steerable distance-measuring interferometers at the corners of a tetrahedron to determine the posi-tions of a retroreflecting target at various locations on the surface being measured. A small wooden breadboard had been built and tested, demonstrating the feasibility of the concept. This paper reports the building of a scaled-up prototype surface measuring machine to allow the measurement of large aspheric surfaces. A major advantage of the device is that, unlike conventional interferometry, it provides surface measurement in absolute coordinates, thus allowing direct determination of radius of curvature. In addition, the device is self-calibrating. Measurements of a 24-inch mirror have been made with the new machine, giving repeatability of 4 µ m peak sag in the curvature and accuracy of 0.7 μm rms in the surface figure at best focus. The device is currently being used in the production grinding of large aspheric mirrors at Itek. The device is potentially scalable to other industries where highly accurate measurement of unusual surfaces is required.

  18. Multiple man-machine interfaces

    NASA Technical Reports Server (NTRS)

    Stanton, L.; Cook, C. W.

    1981-01-01

    The multiple man machine interfaces inherent in military pilot training, their social implications, and the issue of possible negative feedback were explored. Modern technology has produced machines which can see, hear, and touch with greater accuracy and precision than human beings. Consequently, the military pilot is more a systems manager, often doing battle against a target he never sees. It is concluded that unquantifiable human activity requires motivation that is not intrinsic in a machine.

  19. Diamond Machining Applications And Capabilities

    NASA Astrophysics Data System (ADS)

    Benjamin, Roland J.

    1983-12-01

    Aspheric surface generation and precision machining have been important technologies at Hughes Optical Products, Inc. (formerly Optical Division, Bell & Howell Company) for over twenty years. Present machining capabilities and supporting services which are available on a custom basis are described. A variety of applications of diamond machining are illustrated, involving not only the usual reflective materials such as aluminum, copper, and electroless nickel but also such IR refractive materials as germanium, silicon, and chalcogenide glasses.

  20. CANISTER HANDLING FACILITY CRITICALITY SAFETY CALCULATIONS

    SciTech Connect

    C.E. Sanders

    2005-04-07

    This design calculation revises and updates the previous criticality evaluation for the canister handling, transfer and staging operations to be performed in the Canister Handling Facility (CHF) documented in BSC [Bechtel SAIC Company] 2004 [DIRS 167614]. The purpose of the calculation is to demonstrate that the handling operations of canisters performed in the CHF meet the nuclear criticality safety design criteria specified in the ''Project Design Criteria (PDC) Document'' (BSC 2004 [DIRS 171599], Section 4.9.2.2), the nuclear facility safety requirement in ''Project Requirements Document'' (Canori and Leitner 2003 [DIRS 166275], p. 4-206), the functional/operational nuclear safety requirement in the ''Project Functional and Operational Requirements'' document (Curry 2004 [DIRS 170557], p. 75), and the functional nuclear criticality safety requirements described in the ''Canister Handling Facility Description Document'' (BSC 2004 [DIRS 168992], Sections 3.1.1.3.4.13 and 3.2.3). Specific scope of work contained in this activity consists of updating the Category 1 and 2 event sequence evaluations as identified in the ''Categorization of Event Sequences for License Application'' (BSC 2004 [DIRS 167268], Section 7). The CHF is limited in throughput capacity to handling sealed U.S. Department of Energy (DOE) spent nuclear fuel (SNF) and high-level radioactive waste (HLW) canisters, defense high-level radioactive waste (DHLW), naval canisters, multicanister overpacks (MCOs), vertical dual-purpose canisters (DPCs), and multipurpose canisters (MPCs) (if and when they become available) (BSC 2004 [DIRS 168992], p. 1-1). It should be noted that the design and safety analyses of the naval canisters are the responsibility of the U.S. Department of the Navy (Naval Nuclear Propulsion Program) and will not be included in this document. In addition, this calculation is valid for the current design of the CHF and may not reflect the ongoing design evolution of the facility

  1. Analysis for Eccentric Multi Canister Overpack (MCO) Drops at the Canister Storage Building (CSB) (CSB-S-0073)

    SciTech Connect

    HOLLENBECK, R.G.

    2000-05-08

    The Spent Nuclear Fuel (SNF) Canister Storage Building (CSB) is the interim storage facility for the K-Basin SNF at the US. Department of Energy (DOE) Hanford Site. The SNF is packaged in multi-canister overpacks (MCOs). The MCOs are placed inside transport casks, then delivered to the service station inside the CSB. At the service station, the MCO handling machine (MHM) moves the MCO from the cask to a storage tube or one of two sample/weld stations. There are 220 standard storage tubes and six overpack storage tubes in a below grade reinforced concrete vault. Each storage tube can hold two MCOs.

  2. Standardized Curriculum for Machine Tool Operation/Machine Shop.

    ERIC Educational Resources Information Center

    Mississippi State Dept. of Education, Jackson. Office of Vocational, Technical and Adult Education.

    Standardized vocational education course titles and core contents for two courses in Mississippi are provided: machine tool operation/machine shop I and II. The first course contains the following units: (1) orientation; (2) shop safety; (3) shop math; (4) measuring tools and instruments; (5) hand and bench tools; (6) blueprint reading; (7)…

  3. Machine Shop Milling Machines. Oklahoma Trade and Industrial Education.

    ERIC Educational Resources Information Center

    Dunn, James

    This curriculum guide provides instructional materials designed to equip students with basic knowledge and skills that will enable them to enter the machine trades at the machine-operator level. The curriculum is designed for use in full-time secondary and postsecondary classes and part-time adult classes. It can also be adapted to open-entry,…

  4. Production Machine Shop Employment Competencies. Part Four: The Milling Machine.

    ERIC Educational Resources Information Center

    Bishart, Gus; Werner, Claire

    Competencies for production machine shop are provided for the fourth of four topic areas: the milling machine. Each competency appears in a one-page format. It is presented as a goal statement followed by one or more "indicator" statements, which are performance objectives describing an ability that, upon attainment, will establish competency for…

  5. Classifying Structures in the ISM with Machine Learning Techniques

    NASA Astrophysics Data System (ADS)

    Beaumont, Christopher; Goodman, A. A.; Williams, J. P.

    2011-01-01

    The processes which govern molecular cloud evolution and star formation often sculpt structures in the ISM: filaments, pillars, shells, outflows, etc. Because of their morphological complexity, these objects are often identified manually. Manual classification has several disadvantages; the process is subjective, not easily reproducible, and does not scale well to handle increasingly large datasets. We have explored to what extent machine learning algorithms can be trained to autonomously identify specific morphological features in molecular cloud datasets. We show that the Support Vector Machine algorithm can successfully locate filaments and outflows blended with other emission structures. When the objects of interest are morphologically distinct from the surrounding emission, this autonomous classification achieves >90% accuracy. We have developed a set of IDL-based tools to apply this technique to other datasets.

  6. Prototype Vector Machine for Large Scale Semi-Supervised Learning

    SciTech Connect

    Zhang, Kai; Kwok, James T.; Parvin, Bahram

    2009-04-29

    Practicaldataminingrarelyfalls exactlyinto the supervisedlearning scenario. Rather, the growing amount of unlabeled data poses a big challenge to large-scale semi-supervised learning (SSL). We note that the computationalintensivenessofgraph-based SSLarises largely from the manifold or graph regularization, which in turn lead to large models that are dificult to handle. To alleviate this, we proposed the prototype vector machine (PVM), a highlyscalable,graph-based algorithm for large-scale SSL. Our key innovation is the use of"prototypes vectors" for effcient approximation on both the graph-based regularizer and model representation. The choice of prototypes are grounded upon two important criteria: they not only perform effective low-rank approximation of the kernel matrix, but also span a model suffering the minimum information loss compared with the complete model. We demonstrate encouraging performance and appealing scaling properties of the PVM on a number of machine learning benchmark data sets.

  7. Optimal evaluation of array expressions on massively parallel machines

    NASA Technical Reports Server (NTRS)

    Chatterjee, Siddhartha; Gilbert, John R.; Schreiber, Robert; Teng, Shang-Hua

    1992-01-01

    We investigate the problem of evaluating FORTRAN 90 style array expressions on massively parallel distributed-memory machines. On such machines, an elementwise operation can be performed in constant time for arrays whose corresponding elements are in the same processor. If the arrays are not aligned in this manner, the cost of aligning them is part of the cost of evaluating the expression. The choice of where to perform the operation then affects this cost. We present algorithms based on dynamic programming to solve this problem efficiently for a wide variety of interconnection schemes, including multidimensional grids and rings, hypercubes, and fat-trees. We also consider expressions containing operations that change the shape of the arrays, and show that our approach extends naturally to handle this case.

  8. 3D vision assisted flexible robotic assembly of machine components

    NASA Astrophysics Data System (ADS)

    Ogun, Philips S.; Usman, Zahid; Dharmaraj, Karthick; Jackson, Michael R.

    2015-12-01

    Robotic assembly systems either make use of expensive fixtures to hold components in predefined locations, or the poses of the components are determined using various machine vision techniques. Vision-guided assembly robots can handle subtle variations in geometries and poses of parts. Therefore, they provide greater flexibility than the use of fixtures. However, the currently established vision-guided assembly systems use 2D vision, which is limited to three degrees of freedom. The work reported in this paper is focused on flexible automated assembly of clearance fit machine components using 3D vision. The recognition and the estimation of the poses of the components are achieved by matching their CAD models with the acquired point cloud data of the scene. Experimental results obtained from a robot demonstrating the assembly of a set of rings on a shaft show that the developed system is not only reliable and accurate, but also fast enough for industrial deployment.

  9. Prediction of Zeolite Framework Types by a Machine Learning Approach

    NASA Astrophysics Data System (ADS)

    Yang, Shujiang; Lach-Hab, Mohammed; Vaisman, Iosif; Blaisten-Barojas, Estela

    2009-03-01

    Zeolites are microporous crystalline materials with highly regular framework structures consisting of molecular-sized pores and channels. Characteristic framework types of zeolites are traditionally determined by the combined information of coordination sequences and vertex symbols. Here we present a machine learning model for classifying zeolite crystals according to their framework types. An eighteen-dimensional feature vector is defined including topological descriptors and physical/chemical properties of zeolite crystals [Microporous and Mesoporous Materials 117, 339 (2009)]. Trained with crystallographic data of known zeolites, the new model can predict the framework types of unknown zeolite crystals with up to 98 % accuracy. Compared with conventional methods, the machine learning model is more robust handling crystal disorder and/or crystal defects in a more effective manner. This model can be adapted for classifying and clustering other crystalline species.

  10. The Potential to Machine Superconductors with Electrochemical Machining

    NASA Astrophysics Data System (ADS)

    Leese, Rebecca J.; Ivanov, Atanas; Babu-Nadendla, Hari

    2016-01-01

    Superconductors (SCs), such as gadolinium barium copper oxide, are brittle ceramics which are very difficult to machine conventionally due to the easy propagation of cracks. The cracks formed during conventional machining destroy the superconductive properties of the material. As a result a new method to machine ceramic SCs is needed. In this paper, polarization experiments were conducted in various nonaqueous salt electrolytes to determine whether electrochemical machining (ECM) is a suitable method for machining gadolinium barium copper oxide with silver inclusions (GdBCO-Ag) for the first time. Sodium chloride in formic acid proved to be the best electrolyte for this application with higher dissolution rates and achieving a better surface finish. It was noted that GdBCO-Ag dissolved at higher rates in NaCl in formic acid than in other salt-solvent systems.

  11. Extremal quantum cloning machines

    SciTech Connect

    Chiribella, G.; D'Ariano, G. M.; Perinotti, P.; Cerf, N.J.

    2005-10-15

    We investigate the problem of cloning a set of states that is invariant under the action of an irreducible group representation. We then characterize the cloners that are extremal in the convex set of group covariant cloning machines, among which one can restrict the search for optimal cloners. For a set of states that is invariant under the discrete Weyl-Heisenberg group, we show that all extremal cloners can be unitarily realized using the so-called double-Bell states, whence providing a general proof of the popular ansatz used in the literature for finding optimal cloners in a variety of settings. Our result can also be generalized to continuous-variable optimal cloning in infinite dimensions, where the covariance group is the customary Weyl-Heisenberg group of displacement000.

  12. Electropulse chemical machining

    SciTech Connect

    Allen, T.A.; Rospopo, S.D.

    1984-08-01

    Electropulse Chemical Machining is a new technique in chemical milling, and we have applied it to the photoforming of molybdenum. We apply direct current in short pulses at current densities of thousands of amperes per square foot with little thermal degradation of resists or workpieces. We have achieved etch rates an order of magnitude faster than those of existing methods, with a corresponding improvement in surface finish. Equipment designed for pulse plating can be used and is readily available from plating suppliers. Chemicals are commercially available and may be diluted to levels that protect resist images, reduce hazards to personnel, and simplify disposal. We speculate that this process can be applied to other refractory metals and noble metals.

  13. 75 FR 9860 - Release, Handling, and Protection of Restricted Information

    Federal Register 2010, 2011, 2012, 2013, 2014

    2010-03-04

    ... Data and Copyrights, NASA's policy on release and protection and handling of such information. This...-73, Handling and Protection of Restricted Information. The Contractor's limited rights data and... Protection of Restricted Information AGENCY: National Aeronautics and Space Administration. ACTION:...

  14. 30 CFR 77.606 - Energized trailing cables; handling.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... COAL MINES Trailing Cables § 77.606 Energized trailing cables; handling. Energized medium- and high-voltage trailing cables shall be handled only by persons wearing protective rubber gloves (see §...

  15. 30 CFR 77.606 - Energized trailing cables; handling.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... COAL MINES Trailing Cables § 77.606 Energized trailing cables; handling. Energized medium- and high-voltage trailing cables shall be handled only by persons wearing protective rubber gloves (see §...

  16. 30 CFR 77.606 - Energized trailing cables; handling.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... COAL MINES Trailing Cables § 77.606 Energized trailing cables; handling. Energized medium- and high-voltage trailing cables shall be handled only by persons wearing protective rubber gloves (see §...

  17. Training Materials for Handling Claims of Sexual Harassment.

    ERIC Educational Resources Information Center

    Roe, Betty

    1982-01-01

    Reviews resource materials for handling claims of sexual harassment. Includes guidelines for administrators in handling complaints of sexual harassment and discusses the responsibilities of management. Explores the definition of sexual harassment. (RC)

  18. Materials and Fabrication Issues for Large Machined Germanium Immersion Gratings

    SciTech Connect

    Kuzmenko, P J; Davis, P J; Little, S L; Hale, L C

    2006-05-22

    LLNL has successfully fabricated small (1.5 cm{sup 2} area) germanium immersion gratings. We studied the feasibility of producing a large germanium immersion grating by means of single point diamond flycutting. Our baseline design is a 63.4o blaze echelle with a 6 cm beam diameter. Birefringence and refractive index inhomogeneity due to stresses produced by the crystal growth process are of concern. Careful selection of the grating blank and possibly additional annealing to relieve stress will be required. The Large Optics Diamond Turning Machine (LODTM) at LLNL is a good choice for the fabrication. It can handle parts up to 1.5 meter in diameter and 0.5 meter in length and is capable of a surface figure accuracy of better than 28 nm rms. We will describe the machine modifications and the machining process for a large grating. A next generation machine, the Precision Optical Grinder and Lathe (POGAL), currently under development has tighter specifications and could produce large gratings with higher precision.

  19. Machining of uranium and uranium alloys

    SciTech Connect

    Morris, T.O.

    1981-12-14

    Uranium and uranium alloys can be readily machined by conventional methods in the standard machine shop when proper safety and operating techniques are used. Material properties that affect machining processes and recommended machining parameters are discussed. Safety procedures and precautions necessary in machining uranium and uranium alloys are also covered. 30 figures.

  20. Coal handling and distribution: An overview

    SciTech Connect

    Lema, J.E.

    1998-12-31

    Reliable, timely and efficient transportation service for distribution of coal from mines and processing plants to power producers, industrial facilities, and port terminals is a key factor in achieving full utilization of US coal in domestic and international markets. Transportation service must meet standards of performance which not only cover the amount of coal traffic to be handled, but also the quality of the service, especially as expressed in units of time, e.g. train arrival times at mines and processing plants, transit times for coal shipments, and cycle times for trains in dedicated coal transportation service. Although the focus of this presentation is handling and distribution of coal, an important commodity produced by the mining industry, what is said will apply likewise to other mined commodities which, similar to coal, often must be transported as heavy bulk freight in large amounts utilizing railroad and marine services. Turning now to handling and distribution of coal, in particular, five major points will be addressed: (1) coal traffic flows have changed significantly since 1980; (2) the railroad network is under severe pressure with regard to the adequacy of transportation service experienced since 1997; (3) a fresh look is needed to determine what steps are needed to ensure adequate railroad service today and in years ahead; (4) the nation`s inland waterways system is a vital component of the bulk freight distribution network that should be upgraded; (5) intermodalism is a hallmark of coal distribution which should be enhanced by focusing on improving short-line and regional railroad/Class 1 railroad, railroad/barge line, truck/railroad, and truck/barge line connectivity and access to coal terminals.

  1. Facility Concepts for Mars Returned Sample Handling

    NASA Technical Reports Server (NTRS)

    Cohen, Marc M.; Briggs, Geoff (Technical Monitor)

    2001-01-01

    Samples returned from Mars must be held in quarantine until their biological safety has been determined. A significant challenge, unique to NASA's needs, is how to contain the samples (to protect the blaspheme) while simultaneously protecting their pristine nature. This paper presents a comparative analysis of several quarantine facility concepts for handling and analyzing these samples. The considerations in this design analysis include: modes of manipulation; capability for destructive as well as non-destructive testing; avoidance of cross-contamination; linear versus recursive processing; and sample storage and retrieval within a closed system. The ability to rigorously contain biologically hazardous materials has been amply demonstrated by facilities that meet the specifications of the Center for Disease Control Biosafety Level 4. The newly defined Planetary Protection Level Alpha must provide comparable containment while assuring that the samples remain pristine; the latter requirement is based on the need to avoid compromising science analyses by instrumentation of the highest possible sensitivity (among other things this will assure that there is no false positive detection of organisms or organic molecules - a situation that would delay or prevent the release of the samples from quarantine). Protection of the samples against contamination by terrestrial organisms and organic molecules makes a considerable impact upon the sample handling facility. The use of glove boxes appears to be impractical because of their tendency to leak and to surges. As a result, a returned sample quarantine facility must consider the use of automation and remote manipulation to carry out the various functions of sample handling and transfer within the system. The problem of maintaining sensitive and bulky instrumentation under the constraints of simultaneous sample containment and contamination protection also places demands on the architectural configuration of the facility that

  2. The Machine Scoring of Writing

    ERIC Educational Resources Information Center

    McCurry, Doug

    2010-01-01

    This article provides an introduction to the kind of computer software that is used to score student writing in some high stakes testing programs, and that is being promoted as a teaching and learning tool to schools. It sketches the state of play with machines for the scoring of writing, and describes how these machines work and what they do.…

  3. Cleaning of Free Machining Brass

    SciTech Connect

    Shen, T

    2005-12-29

    We have investigated four brightening treatments proposed by two cleaning vendors for cleaning free machining brass. The experimental results showed that none of the proposed brightening treatments passed the swipe test. Thus, we maintain the recommendation of not using the brightening process in the cleaning of free machining brass for NIF application.

  4. Self-Adjusting Teaching Machines.

    ERIC Educational Resources Information Center

    Dovgyallo, A. M.

    A study was made on the synthesis of teaching machine elements to ensure the stabilization of the chi indicator of the teaching process of each student. At first, a procedure was developed for calculating the chi indicator for the case when the teaching machine predicts the magnitude of this indicator based on probabilities derived from an…

  5. Contraction-Only Exercise Machine

    NASA Technical Reports Server (NTRS)

    Doerr, Donald F.; Maples, Arthur B.; Campbell, Craig M.

    1992-01-01

    Standard knee-extension machine modified so subject experiences force only when lifting leg against stack of weights. Exerts little force on leg while being lowered. Hydraulic cylinder and reservoir mounted on frame of exercise machine. Fluid flows freely from cylinder to reservoir during contraction (lifting) but in constricted fashion from reservoir to cylinder during extension (lowering).

  6. The Machine Intelligence Hex Project

    ERIC Educational Resources Information Center

    Chalup, Stephan K.; Mellor, Drew; Rosamond, Fran

    2005-01-01

    Hex is a challenging strategy board game for two players. To enhance students' progress in acquiring understanding and practical experience with complex machine intelligence and programming concepts we developed the Machine Intelligence Hex (MIHex) project. The associated undergraduate student assignment is about designing and implementing Hex…

  7. Machine Trades Lab Management Guide.

    ERIC Educational Resources Information Center

    Ohio State Univ., Columbus. Instructional Materials Lab.

    This manual was developed to guide machine trades instructors and vocational supervisors in sequencing laboratory instruction and controlling the flow of work for a 2-year machine trades training program. The first part of the guide provides information on program management (program description, safety concerns, academic issues, implementation…

  8. Man and Machines: Three Criticisms.

    ERIC Educational Resources Information Center

    Schneider, Edward F.

    As machines have become a more common part of daily life through the passage of time, the idea that the line separating man and machine is slowly fading has become more popular as well. This paper examines three critics of change through their most famous works. One of the most popular views of Mary Shelley's "Frankenstein" is that it is a…

  9. TEACHING MACHINES AND PROGRAMED INSTRUCTION.

    ERIC Educational Resources Information Center

    JOHNSON, HERBERT; AND OTHERS

    THE TEACHING MACHINE AND PROGRAMED INSTRUCTION ARE EXPLAINED ANALYTICALLY IN TERMS OF LABORATORY PROCEDURES. AN EXPLANATION IS GIVEN OF THE PSYCHOLOGY OF THE STUDENT. TEACHING MACHINES ALLEVIATE SOME PROBLEMS OF STUDENT-TEACHER RELATIONSHIPS, SUCH AS APATHY, STUBBORNNESS, AND RESENTMENT. HIGHER LEVELS OF CONCENTRATION ARE MAINTAINED. SOME…

  10. TEACHING MACHINE STUDY. FINAL REPORT.

    ERIC Educational Resources Information Center

    EVCO, Albuquerque, NM.

    IN AN INVESTIGATION OF THE POTENTIAL OF TEACHING MACHINES IN THE JOB CORPS MATHEMATICS PROGRAM, EXISTING JOB CORPS ARITHMETIC MATERIAL WAS PREPARED FOR INSTRUCTION BY MACHINE AND PROGRAMED TEXT, AND THEN FIELD TESTED. REVISIONS WERE MADE, AND A PROGRAMED MANUAL FOR INSTRUCTORS WRITTEN, AFTER WHICH A NEW FIELD TEST WAS RUN. IN THE INITIAL FIELD…

  11. Machine Shop: Scope and Sequence.

    ERIC Educational Resources Information Center

    Nashville - Davidson County Metropolitan Public Schools, TN.

    Intended for use by all machine shop instructors in the Metropolitan Nashville Public Schools, this guide provides a sequential listing of course content and scope. A course description provides a brief overview of the content of the courses offered in the machine shop program. General course objectives are then listed. Outlines of the course…

  12. Man Machine Systems in Education.

    ERIC Educational Resources Information Center

    Sall, Malkit S.

    This review of the research literature on the interaction between humans and computers discusses how man machine systems can be utilized effectively in the learning-teaching process, especially in secondary education. Beginning with a definition of man machine systems and comments on the poor quality of much of the computer-based learning material…

  13. CANISTER HANDLING FACILITY WORKER DOSE ASSESSMENT

    SciTech Connect

    D.T. Dexheimer

    2004-02-27

    The purpose of this calculation is to estimate radiation doses received by personnel working in the Canister Handling Facility (CHF) performing operations to receive transportation casks, transfer wastes, prepare waste packages, perform associated equipment maintenance. The specific scope of work contained in this calculation covers individual worker group doses on an annual basis, and includes the contributions due to external and internal radiation. The results of this calculation will be used to support the design of the CHF and provide occupational dose estimates for the License Application.

  14. Level measurement solutions for coal handling applications

    SciTech Connect

    Koeneman, D.; Sholette, W.

    2006-06-15

    The article looks at the range and applications of level measurement technology for coal handling and related fly ash operations. Point level or on/off measurement instrumentation indicates the presence or absence of material in a surge bin storage silo or on a conveyor belt. Point level switches at high or low level turn on or turn off pumps and conveyors. Continuous level or proportional measurement indicates the level in a vessel over the full span of measurement. The article describes types of technologies in typical locations in a coal-fired power plant where point and continuous level measurements are taken. 1 fig.

  15. The Remote-Handled TRU Waste Program

    SciTech Connect

    Gist, C. S.; Plum, H. L.; Wu, C. F.; Most, W. A.; Burrington, T. P.; Spangler, L. R.

    2002-02-26

    RH TRU Waste is radioactive waste that requires shielding in addition to that provided by the container to protect people nearby from radiation exposure. By definition, the radiation dose rate at the outer surface of the container is greater than 200 millirem per hour and less than 1,000 rem per hour. The DOE is proposing a process for the characterization of RH TRU waste planned for disposal in the WIPP. This characterization process represents a performance-driven approach that satisfies the requirements of the New Mexico Hazardous Waste Act, the Environmental Protection Agency (EPA) regulations for WIPP long-term performance, the transportation requirements of the Nuclear Regulatory Commission (NRC) and the Department of Transportation, as well as the technical safety requirements of RH TRU waste handling. The transportation, management and disposal of RH TRU waste is regulated by external government agencies as well as by the DOE itself. Externally, the characterization of RH-TRU waste for disposal at the WIPP is regulated by 20.4.1.500 New Mexico Administrative Code (incorporating 40 CFR 261.13) for the hazardous constituents and 40 CFR 194.24 for the radioactive constituents. The Nuclear Regulatory Commission certifies the shipping casks and the transportation system must meet DOT regulations. Internally, the DOE evaluates the environmental impacts of RH TRU waste transportation, handling and disposal through its National Environmental Policy Act program. The operational safety is assessed in the RH TRU Waste Safety Analysis Report, to be approved by the DOE. The WIPP has prepared a modification request to the Hazardous Waste Facility Permit that includes modifications to the WIPP facility for the safe receipt and handling of RH TRU waste and the addition of an RH TRU waste analysis plan. Modifications to the facility include systems and equipment for safe handling of RHTRU containers. Two shipping casks are to be used to optimize RH TRU was te throughput

  16. Factors influencing aircraft ground handling performance

    NASA Technical Reports Server (NTRS)

    Yager, T. J.

    1983-01-01

    Problems associated with aircraft ground handling operations on wet runways are discussed and major factors which influence tire/runway braking and cornering traction capability are identified including runway characteristics, tire hydroplaning, brake system anomalies, and pilot inputs. Research results from tests with instrumented ground vehicles and aircraft, and aircraft wet runway accident investigation are summarized to indicate the effects of different aircraft, tire, and runway parameters. Several promising means are described for improving tire/runway water drainage capability, brake system efficiency, and pilot training to help optimize aircraft traction performance on wet runways.

  17. CLASSIFICATION OF THE MGR MUCK HANDLING SYSTEM

    SciTech Connect

    R. Garrett

    1999-08-31

    The purpose of this analysis is to document the Quality Assurance (QA) classification of the Monitored Geologic Repository (MGR) muck handling system structures, systems and components (SSCs) performed by the MGR Safety Assurance Department. This analysis also provides the basis for revision of YMP/90-55Q, Q-List (YMP 1998). The Q-List identifies those MGR SSCs subject to the requirements of DOE/RW-0333P, ''Quality Assurance Requirements and Description (QARD) (DOE 1998). This QA classification incorporates the current MGR design and the results of the ''Preliminary Preclosure Design Basis Event Calculations for the Monitored Geologic Repository (CRWMS M and O 1998a).

  18. APPARATUS FOR HANDLING MIXTURES OF SOLID MATERIALS

    DOEpatents

    Hubbell, J.P.

    1959-08-25

    An apparatus is described for handling either a mixture of finely subdivided materials or a single material requiring a compacting action thereon preparatory to a chemical reducing process carried out in a crucible container. The apparatus is designed to deposit a mixture of dust-forming solid materials in a container while confining the materials against escape into the surrounding atmosphere. A movable filling tube, having a compacting member, is connected to the container and to a covered hopper receiving the mixture of materials. The filling tube is capable of reciprocating in the container and their relative positions are dependent upon the pressure established upon the material by the compacting member.

  19. Fluid handling properties of hydrogel dressings.

    PubMed

    Thomas, S; Hay, P

    1995-04-01

    The fluid handling properties of four hydrogel dressings were examined in a laboratory-based study to determine their ability to absorb liquid from or donate liquid to a range of standard test substrates simulating wound tissue in various states of hydration. The tests suggest that three of the dressings are likely to be effective fluid-donating agents, and one of the dressings has a dual ability to donate or absorb liquid depending upon moisture content and nature of the substrate to which it is applied. These observations are discussed in the context of the clinical use of hydrogel dressings.

  20. IAQ and air handling unit design

    SciTech Connect

    Gill, K.E.

    1996-01-01

    Indoor air quality (IAQ) concerns are affecting the design of air handlers currently being offered by the manufacturers of equipment in the marketplace. These design changes are being driven by increased awareness, code changes, literature, and lawsuits within the HVAC industry. The design professionals who apply the manufacturers` products are acutely aware of the need to improve the quality of air within buildings. With the new awareness of indoor air quality issues come more options, different construction techniques, and modularity in air handling unit design.

  1. WASTE HANDLING BUILDING SHIELD WALL ANALYSIS

    SciTech Connect

    D. Padula

    2000-01-13

    The scope of this analysis is to estimate the shielding wall, ceiling or equivalent door thicknesses that will be required in the Waste Handling Building to maintain the radiation doses to personnel within acceptable limits. The shielding thickness calculated is the minimum required to meet administrative limits, and not necessarily what will be recommended for the final design. The preliminary evaluations will identify the areas which have the greatest impact on mechanical and facility design concepts. The objective is to provide the design teams with the necessary information to assure an efficient and effective design.

  2. Conditioning laboratory cats to handling and transport.

    PubMed

    Gruen, Margaret E; Thomson, Andrea E; Clary, Gillian P; Hamilton, Alexandra K; Hudson, Lola C; Meeker, Rick B; Sherman, Barbara L

    2013-10-01

    As research subjects, cats have contributed substantially to our understanding of biological systems, from the development of mammalian visual pathways to the pathophysiology of feline immunodeficiency virus as a model for human immunodeficiency virus. Few studies have evaluated humane methods for managing cats in laboratory animal facilities, however, in order to reduce fear responses and improve their welfare. The authors describe a behavioral protocol used in their laboratory to condition cats to handling and transport. Such behavioral conditioning benefits the welfare of the cats, the safety of animal technicians and the quality of feline research data.

  3. Analysis of handling noises on wound strings.

    PubMed

    Pakarinen, J; Penttinen, H; Bank, B

    2007-12-01

    This study analyzes the handling noises that occur when a finger is slid along a wound string. The resulting noise has a harmonic structure due to the periodic texture of the wound string. The frequency of the harmonics and the root-mean-square amplitude of the noise were found to be linearly proportional to the sliding speed. In addition, the sliding excites the longitudinal modes of the string, thus resulting in a set of static harmonics in the noise spectrum. The sliding excites different longitudinal modes depending on the sliding location. PMID:18247641

  4. System for handling and storing radioactive waste

    DOEpatents

    Anderson, J.K.; Lindemann, P.E.

    1982-07-19

    A system and method are claimed for handling and storing spent reactor fuel and other solid radioactive waste, including canisters to contain the elements of solid waste, storage racks to hold a plurality of such canisters, storage bays to store these racks in isolation by means of shielded doors in the bays. This system also includes means for remotely positioning the racks in the bays and an access tunnel within which the remotely operated means is located to position a rack in a selected bay. The modular type of these bays will facilitate the construction of additional bays and access tunnel extension.

  5. System for handling and storing radioactive waste

    DOEpatents

    Anderson, John K.; Lindemann, Paul E.

    1984-01-01

    A system and method for handling and storing spent reactor fuel and other solid radioactive waste, including canisters to contain the elements of solid waste, storage racks to hold a plurality of such canisters, storage bays to store these racks in isolation by means of shielded doors in the bays. This system also includes means for remotely positioning the racks in the bays and an access tunnel within which the remotely operated means is located to position a rack in a selected bay. The modular type of these bays will facilitate the construction of additional bays and access tunnel extension.

  6. DISPOSAL CONTAINER HANDLING SYSTEM DESCRIPTION DOCUMENT

    SciTech Connect

    E. F. Loros

    2000-06-30

    The Disposal Container Handling System receives and prepares new disposal containers (DCs) and transfers them to the Assembly Transfer System (ATS) or Canister Transfer System (CTS) for loading. The system receives the loaded DCs from ATS or CTS and welds the lids. When the welds are accepted the DCs are termed waste packages (WPs). The system may stage the WP for later transfer or transfer the WP directly to the Waste Emplacement/Retrieval System. The system can also transfer DCs/WPs to/from the Waste Package Remediation System. The Disposal Container Handling System begins with new DC preparation, which includes installing collars, tilting the DC upright, and outfitting the container for the specific fuel it is to receive. DCs and their lids are staged in the receipt area for transfer to the needed location. When called for, a DC is put on a cart and sent through an airlock into a hot cell. From this point on, all processes are done remotely. The DC transfer operation moves the DC to the ATS or CTS for loading and then receives the DC for welding. The DC welding operation receives loaded DCs directly from the waste handling lines or from interim lag storage for welding of the lids. The welding operation includes mounting the DC on a turntable, removing lid seals, and installing and welding the inner and outer lids. After the weld process and non-destructive examination are successfully completed, the WP is either staged or transferred to a tilting station. At the tilting station, the WP is tilted horizontally onto a cart and the collars removed. The cart is taken through an air lock where the WP is lifted, surveyed, decontaminated if required, and then moved into the Waste Emplacement/Retrieval System. DCs that do not meet the welding non-destructive examination criteria are transferred to the Waste Package Remediation System for weld preparation or removal of the lids. The Disposal Container Handling System is contained within the Waste Handling Building System

  7. 16 CFR 1207.10 - Handling, storage, and marking.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 16 Commercial Practices 2 2013-01-01 2013-01-01 false Handling, storage, and marking. 1207.10... REGULATIONS SAFETY STANDARD FOR SWIMMING POOL SLIDES § 1207.10 Handling, storage, and marking. (a) Marking... identification of the manufacturer. (b) Shipping, handling, and storage. The slide shall be designed,...

  8. 9 CFR 114.11 - Storage and handling.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Storage and handling. 114.11 Section... BIOLOGICAL PRODUCTS § 114.11 Storage and handling. Biological products at licensed establishments shall be protected at all times against improper storage and handling. Completed product shall be kept...

  9. 16 CFR 1207.10 - Handling, storage, and marking.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 16 Commercial Practices 2 2012-01-01 2012-01-01 false Handling, storage, and marking. 1207.10... REGULATIONS SAFETY STANDARD FOR SWIMMING POOL SLIDES § 1207.10 Handling, storage, and marking. (a) Marking... identification of the manufacturer. (b) Shipping, handling, and storage. The slide shall be designed,...

  10. 9 CFR 114.11 - Storage and handling.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Storage and handling. 114.11 Section... BIOLOGICAL PRODUCTS § 114.11 Storage and handling. Biological products at licensed establishments shall be protected at all times against improper storage and handling. Completed product shall be kept...

  11. 16 CFR 1207.10 - Handling, storage, and marking.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 16 Commercial Practices 2 2014-01-01 2014-01-01 false Handling, storage, and marking. 1207.10... REGULATIONS SAFETY STANDARD FOR SWIMMING POOL SLIDES § 1207.10 Handling, storage, and marking. (a) Marking... identification of the manufacturer. (b) Shipping, handling, and storage. The slide shall be designed,...

  12. 7 CFR 984.72 - Reports of merchantable walnuts handled.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 8 2012-01-01 2012-01-01 false Reports of merchantable walnuts handled. 984.72... SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE WALNUTS... merchantable walnuts handled. Each handler who handles merchantable walnuts, inshell or shelled, at any...

  13. 7 CFR 984.72 - Reports of merchantable walnuts handled.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 8 2014-01-01 2014-01-01 false Reports of merchantable walnuts handled. 984.72... SERVICE (MARKETING AGREEMENTS AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE WALNUTS... merchantable walnuts handled. Each handler who handles merchantable walnuts, inshell or shelled, at any...

  14. 7 CFR 984.72 - Reports of merchantable walnuts handled.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 8 2013-01-01 2013-01-01 false Reports of merchantable walnuts handled. 984.72... SERVICE (MARKETING AGREEMENTS AND ORDERS; FRUITS, VEGETABLES, NUTS), DEPARTMENT OF AGRICULTURE WALNUTS... merchantable walnuts handled. Each handler who handles merchantable walnuts, inshell or shelled, at any...

  15. 7 CFR 984.72 - Reports of merchantable walnuts handled.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 8 2010-01-01 2010-01-01 false Reports of merchantable walnuts handled. 984.72... SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE WALNUTS... merchantable walnuts handled. Each handler who handles merchantable walnuts, inshell or shelled, at any...

  16. 7 CFR 984.72 - Reports of merchantable walnuts handled.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Reports of merchantable walnuts handled. 984.72... SERVICE (Marketing Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE WALNUTS... merchantable walnuts handled. Each handler who handles merchantable walnuts, inshell or shelled, at any...

  17. 21 CFR 58.107 - Test and control article handling.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 1 2012-04-01 2012-04-01 false Test and control article handling. 58.107 Section... GOOD LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Test and Control Articles § 58.107 Test and control article handling. Procedures shall be established for a system for the handling of the test...

  18. 21 CFR 58.107 - Test and control article handling.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 1 2014-04-01 2014-04-01 false Test and control article handling. 58.107 Section... GOOD LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Test and Control Articles § 58.107 Test and control article handling. Procedures shall be established for a system for the handling of the test...

  19. 21 CFR 58.107 - Test and control article handling.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 1 2011-04-01 2011-04-01 false Test and control article handling. 58.107 Section... GOOD LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Test and Control Articles § 58.107 Test and control article handling. Procedures shall be established for a system for the handling of the test...

  20. 21 CFR 58.107 - Test and control article handling.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 1 2013-04-01 2013-04-01 false Test and control article handling. 58.107 Section... GOOD LABORATORY PRACTICE FOR NONCLINICAL LABORATORY STUDIES Test and Control Articles § 58.107 Test and control article handling. Procedures shall be established for a system for the handling of the test...

  1. Materials Handling. Module SH-01. Safety and Health.

    ERIC Educational Resources Information Center

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on materials handling is one of 50 modules concerned with job safety and health. It presents the procedures for safe materials handling. Discussed are manual handling methods (lifting and carrying by hand) and mechanical lifting (lifting by powered trucks, cranes or conveyors). Following the introduction, 15 objectives (each…

  2. 30 CFR 77.1303 - Explosives, handling and use.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle explosives or detonators shall be experienced men who understand the hazards involved; trainees shall do...

  3. 30 CFR 77.1303 - Explosives, handling and use.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle explosives or detonators shall be experienced men who understand the hazards involved; trainees shall do...

  4. 30 CFR 77.1303 - Explosives, handling and use.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle explosives or detonators shall be experienced men who understand the hazards involved; trainees shall do...

  5. 30 CFR 77.1303 - Explosives, handling and use.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle explosives or detonators shall be experienced men who understand the hazards involved; trainees shall do...

  6. 30 CFR 77.1303 - Explosives, handling and use.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Explosives, handling and use. 77.1303 Section... MINES Explosives and Blasting § 77.1303 Explosives, handling and use. (a) Persons who use or handle explosives or detonators shall be experienced men who understand the hazards involved; trainees shall do...

  7. 7 CFR 959.126 - Handling of culls.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 8 2011-01-01 2011-01-01 false Handling of culls. 959.126 Section 959.126 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulations Safeguards § 959.126 Handling of culls. (a) The handling of culls, i.e., onions which fail to...

  8. 29 CFR 1910.176 - Handling materials-general.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 29 Labor 5 2011-07-01 2011-07-01 false Handling materials-general. 1910.176 Section 1910.176 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR OCCUPATIONAL SAFETY AND HEALTH STANDARDS Materials Handling and Storage § 1910.176 Handling materials—general. (a) Use of...

  9. 48 CFR 1852.211-70 - Packaging, handling, and transportation.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... 48 Federal Acquisition Regulations System 6 2011-10-01 2011-10-01 false Packaging, handling, and... and Clauses 1852.211-70 Packaging, handling, and transportation. As prescribed in 1811.404-70, insert the following clause: Packaging, Handling, and Transportation (SEP 2005) (a) The Contractor...

  10. Characterization of nanoparticles from abrasive waterjet machining and electrical discharge machining processes.

    PubMed

    Ling, Tsz Yan; Pui, David Y H

    2013-11-19

    Abrasive Waterjet Machining (AWM) and Electrical Discharge Machining (EDM) processes are found to produce nanoparticles during operation. Impacts of engineered nanoparticles released to the environment and biological system have caused much concern. Similarly, the nanoparticles unintentionally produced by the AWM and EDM can lead to comparable effects. By application of the Nanoparticle Tracking Analysis (NTA) technique, the size distribution and concentration of nanoparticles in the water used in AWM and EDM were measured. The particles generally have a peak size of 100-200 nm. The filtration systems of the AWM and EDM processes were found to remove 70% and 90% the nanoparticles present, respectively. However, the particle concentration of the filtered water from the AWM was still four times higher than that found in regular tap water. These nanoparticles are mostly agglomerated, according to the microscopy analysis. Using the electron dispersive spectroscopy (EDS) technique, the particles are confirmed to come from the debris of the materials cut with the equipment. Since AWM and EDM are widely used, the handling and disposal of used filters collected with nanoparticles, release of nanoparticles to the sewer, and potential use of higher performance filters for these processes will deserve further consideration.

  11. Characterization of nanoparticles from abrasive waterjet machining and electrical discharge machining processes.

    PubMed

    Ling, Tsz Yan; Pui, David Y H

    2013-11-19

    Abrasive Waterjet Machining (AWM) and Electrical Discharge Machining (EDM) processes are found to produce nanoparticles during operation. Impacts of engineered nanoparticles released to the environment and biological system have caused much concern. Similarly, the nanoparticles unintentionally produced by the AWM and EDM can lead to comparable effects. By application of the Nanoparticle Tracking Analysis (NTA) technique, the size distribution and concentration of nanoparticles in the water used in AWM and EDM were measured. The particles generally have a peak size of 100-200 nm. The filtration systems of the AWM and EDM processes were found to remove 70% and 90% the nanoparticles present, respectively. However, the particle concentration of the filtered water from the AWM was still four times higher than that found in regular tap water. These nanoparticles are mostly agglomerated, according to the microscopy analysis. Using the electron dispersive spectroscopy (EDS) technique, the particles are confirmed to come from the debris of the materials cut with the equipment. Since AWM and EDM are widely used, the handling and disposal of used filters collected with nanoparticles, release of nanoparticles to the sewer, and potential use of higher performance filters for these processes will deserve further consideration. PMID:24144041

  12. Humans, animals, robots: handling volumic data flows

    NASA Astrophysics Data System (ADS)

    Petrov, Valery

    1999-08-01

    Human visual system is properly suited for reliable and adequate volumetric perception of natural environment. Volumetric data flows coming from the outer physical space are easily acquired, transferred and processed by eye-brain system in real time. This relates also to the animals which use different complicate mechanisms of optical volumetric data acquisition and can navigate safely at high speeds. On the contrary machine vision systems utilizing currently the stereoscopic effect in attempt to achieve volumetric data presentation are very slow, bulky and in a way inelegantly devised. The stereoscopy itself seems can hardly organize the adequate, real time volumetric robot vision.

  13. Mark 4A antenna control system data handling architecture study

    NASA Technical Reports Server (NTRS)

    Briggs, H. C.; Eldred, D. B.

    1991-01-01

    A high-level review was conducted to provide an analysis of the existing architecture used to handle data and implement control algorithms for NASA's Deep Space Network (DSN) antennas and to make system-level recommendations for improving this architecture so that the DSN antennas can support the ever-tightening requirements of the next decade and beyond. It was found that the existing system is seriously overloaded, with processor utilization approaching 100 percent. A number of factors contribute to this overloading, including dated hardware, inefficient software, and a message-passing strategy that depends on serial connections between machines. At the same time, the system has shortcomings and idiosyncrasies that require extensive human intervention. A custom operating system kernel and an obscure programming language exacerbate the problems and should be modernized. A new architecture is presented that addresses these and other issues. Key features of the new architecture include a simplified message passing hierarchy that utilizes a high-speed local area network, redesign of particular processing function algorithms, consolidation of functions, and implementation of the architecture in modern hardware and software using mainstream computer languages and operating systems. The system would also allow incremental hardware improvements as better and faster hardware for such systems becomes available, and costs could potentially be low enough that redundancy would be provided economically. Such a system could support DSN requirements for the foreseeable future, though thorough consideration must be given to hard computational requirements, porting existing software functionality to the new system, and issues of fault tolerance and recovery.

  14. Mark 4A antenna control system data handling architecture study

    NASA Astrophysics Data System (ADS)

    Briggs, H. C.; Eldred, D. B.

    1991-11-01

    A high-level review was conducted to provide an analysis of the existing architecture used to handle data and implement control algorithms for NASA's Deep Space Network (DSN) antennas and to make system-level recommendations for improving this architecture so that the DSN antennas can support the ever-tightening requirements of the next decade and beyond. It was found that the existing system is seriously overloaded, with processor utilization approaching 100 percent. A number of factors contribute to this overloading, including dated hardware, inefficient software, and a message-passing strategy that depends on serial connections between machines. At the same time, the system has shortcomings and idiosyncrasies that require extensive human intervention. A custom operating system kernel and an obscure programming language exacerbate the problems and should be modernized. A new architecture is presented that addresses these and other issues. Key features of the new architecture include a simplified message passing hierarchy that utilizes a high-speed local area network, redesign of particular processing function algorithms, consolidation of functions, and implementation of the architecture in modern hardware and software using mainstream computer languages and operating systems. The system would also allow incremental hardware improvements as better and faster hardware for such systems becomes available, and costs could potentially be low enough that redundancy would be provided economically. Such a system could support DSN requirements for the foreseeable future, though thorough consideration must be given to hard computational requirements, porting existing software functionality to the new system, and issues of fault tolerance and recovery.

  15. Safe handling of cytotoxics: guideline recommendations

    PubMed Central

    Easty, A.C.; Coakley, N.; Cheng, R.; Cividino, M.; Savage, P.; Tozer, R.; White, R.E.

    2015-01-01

    Background This evidence-based practice guideline was developed to update and address new issues in the handling of cytotoxics, including the use of oral cytotoxics; the selection and use of personal protective equipment; and treatment in diverse settings, including the home setting. Methods The guideline was developed primarily from an adaptation and endorsement of an existing guideline and from three systematic reviews. Before publication, the guideline underwent a series of peer and external reviews to gather feedback. All comments were addressed, and the guideline was amended when required. The guideline applies to health care workers who could come into contact with cytotoxic drugs at any point in the medication circuit. The intended users are hospital administrators, educators, and managers; occupational health and safety services; and pharmacy and health care workers. Results The recommendations represent a reasonable and practical set of procedures that the intended users of this guideline should implement to minimize opportunities for accidental exposure. They are not limited to just the point of care; they cover the entire chain of cytotoxics handling from the time such agents enter the institution until they leave in the patient or as waste. Conclusions Reducing the likelihood of accidental exposure to cytotoxic agents within the medication circuit is the main objective of this evidenced-based guideline. The recommendations differ slightly from earlier guidelines because of the availability of new evidence. PMID:25684994

  16. SpaceWire Data Handling Demonstration System

    NASA Astrophysics Data System (ADS)

    Mills, S.; Parkes, S. M.; O'Gribin, N.

    2007-08-01

    The SpaceWire standard was published in 2003 with the aim of providing a standard for onboard communications, defining the physical and data link layers of an interconnection, in order to improve reusability, reliability and to reduce the cost of mission development. The many benefits which it provides mean that it has already been used in a number of missions, both in Europe and throughout the world. Recent work by the SpaceWire community has included the development of higher level protocols for SpaceWire, such as the Remote Memory Access Protocol (RMAP) which can be used for many purposes, including the configuration of SpaceWire devices. Although SpaceWire has become very popular, the various ways in which it can be used are still being discovered, as are the most efficient ways to use it. At the same time, some in the space industry are not even aware of SpaceWire's existence. This paper describes the SpaceWire Data Handling Demonstration System that has been developed by the University of Dundee. This system simulates an onboard data handling network based on SpaceWire. It uses RMAP for all communication, and so demonstrates how SpaceWire and standardised higher level protocols can be used onboard a spacecraft. The system is not only a good advert for those who are unfamiliar with the benefits of SpaceWire, it is also a useful tool for those using SpaceWire to test ideas.

  17. Robotic liquid handling and automation in epigenetics.

    PubMed

    Gaisford, Wendy

    2012-10-01

    Automated liquid-handling robots and high-throughput screening (HTS) are widely used in the pharmaceutical industry for the screening of large compound libraries, small molecules for activity against disease-relevant target pathways, or proteins. HTS robots capable of low-volume dispensing reduce assay setup times and provide highly accurate and reproducible dispensing, minimizing variation between sample replicates and eliminating the potential for manual error. Low-volume automated nanoliter dispensers ensure accuracy of pipetting within volume ranges that are difficult to achieve manually. In addition, they have the ability to potentially expand the range of screening conditions from often limited amounts of valuable sample, as well as reduce the usage of expensive reagents. The ability to accurately dispense lower volumes provides the potential to achieve a greater amount of information than could be otherwise achieved using manual dispensing technology. With the emergence of the field of epigenetics, an increasing number of drug discovery companies are beginning to screen compound libraries against a range of epigenetic targets. This review discusses the potential for the use of low-volume liquid handling robots, for molecular biological applications such as quantitative PCR and epigenetics. PMID:22933618

  18. Robotic liquid handling and automation in epigenetics.

    PubMed

    Gaisford, Wendy

    2012-10-01

    Automated liquid-handling robots and high-throughput screening (HTS) are widely used in the pharmaceutical industry for the screening of large compound libraries, small molecules for activity against disease-relevant target pathways, or proteins. HTS robots capable of low-volume dispensing reduce assay setup times and provide highly accurate and reproducible dispensing, minimizing variation between sample replicates and eliminating the potential for manual error. Low-volume automated nanoliter dispensers ensure accuracy of pipetting within volume ranges that are difficult to achieve manually. In addition, they have the ability to potentially expand the range of screening conditions from often limited amounts of valuable sample, as well as reduce the usage of expensive reagents. The ability to accurately dispense lower volumes provides the potential to achieve a greater amount of information than could be otherwise achieved using manual dispensing technology. With the emergence of the field of epigenetics, an increasing number of drug discovery companies are beginning to screen compound libraries against a range of epigenetic targets. This review discusses the potential for the use of low-volume liquid handling robots, for molecular biological applications such as quantitative PCR and epigenetics.

  19. Thermal analog device reduces machining errors

    NASA Technical Reports Server (NTRS)

    Mcclure, E. R.

    1972-01-01

    Thermal analog devices predict thermal expansion and contraction of machine structures subjected to various heat inputs. Analog devices correct positioning of machine tools to compensate for distortion of machine frame.

  20. HUMAN MACHINE COOPERATIVE TELEROBOTICS

    SciTech Connect

    William R. Hamel; Spivey Douglass; Sewoong Kim; Pamela Murray; Yang Shou; Sriram Sridharan; Ge Zhang; Scott Thayer; Rajiv V. Dubey

    2003-06-30

    described as Human Machine Cooperative Telerobotics (HMCTR). The HMCTR combines the telerobot with robotic control techniques to improve the system efficiency and reliability in teleoperation mode. In this topical report, the control strategy, configuration and experimental results of Human Machines Cooperative Telerobotics (HMCTR), which modifies and limits the commands of human operator to follow the predefined constraints in the teleoperation mode, is described. The current implementation is a laboratory-scale system that will be incorporated into an engineering-scale system at the Oak Ridge National Laboratory in the future.