A pilot's assessment of helicopter handling-quality factors common to both agility and instrument flying tasks

NASA Technical Reports Server (NTRS)

Gerdes, R. M.

1980-01-01

A series of simulation and flight investigations were undertaken to evaluate helicopter flying qualities and the effects of control system augmentation for nap-of-the-Earth (NOE) agility and instrument flying tasks. Handling quality factors common to both tasks were identified. Precise attitude control was determined to be a key requirement for successful accomplishment of both tasks. Factors that degraded attitude controllability were improper levels of control sensitivity and damping, and rotor system cross coupling due to helicopter angular rate and collective pitch input. Application of rate command, attitude command, and control input decouple augmentation schemes enhanced attitude control and significantly improved handling qualities for both tasks. The NOE agility and instrument flying handling quality considerations, pilot rating philosophy, and supplemental flight evaluations are also discussed.

A pilot's assessment of helicopter handling-quality factors common to both agility and instrument flying tasks

NASA Technical Reports Server (NTRS)

Gerdes, R. M.

1980-01-01

Results from a series of simulation and flight investigations undertaken to evaluate helicopter flying qualities and the effects of control system augmentation for nap-of-the-earth (NOE) agility and instrument flying tasks were analyzed to assess handling-quality factors common to both tasks. Precise attitude control was determined to be a key requirement for successful accomplishment of both tasks. Factors that degraded attitude controllability were improper levels of control sensitivity and damping and rotor-system cross-coupling due to helicopter angular rate and collective pitch input. Application of rate-command, attitude-command, and control-input decouple augmentation schemes enhanced attitude control and significantly improved handling qualities for both tasks. NOE agility and instrument flying handling-quality considerations, pilot rating philosophy, and supplemental flight evaluations are also discussed.

Handling Qualities Implications for Crewed Spacecraft Operations

NASA Technical Reports Server (NTRS)

Bailey, Randall E.; Jackson, E. Bruce; Arthur, J. J.

2012-01-01

Abstract Handling qualities embody those qualities or characteristics of an aircraft that govern the ease and precision with which a pilot is able to perform the tasks required in support of an aircraft role. These same qualities are as critical, if not more so, in the operation of spacecraft. A research, development, test, and evaluation process was put into effect to identify, understand, and interpret the engineering and human factors principles which govern the pilot-vehicle dynamic system as they pertain to space exploration missions and tasks. Toward this objective, piloted simulations were conducted at the NASA Langley Research Center and Ames Research Center for earth-orbit proximity operations and docking and lunar landing. These works provide broad guidelines for the design of spacecraft to exhibit excellent handling characteristics. In particular, this work demonstrates how handling qualities include much more than just stability and control characteristics of a spacecraft or aircraft. Handling qualities are affected by all aspects of the pilot-vehicle dynamic system, including the motion, visual and aural cues of the vehicle response as the pilot performs the required operation or task. A holistic approach to spacecraft design, including the use of manual control, automatic control, and pilot intervention/supervision is described. The handling qualities implications of design decisions are demonstrated using these pilot-in-the-loop evaluations of docking operations and lunar landings.

Orion Handling Qualities During ISS Rendezvous and Docking

NASA Technical Reports Server (NTRS)

Hart, Jeremy J.; Stephens, J. P.; Spehar, P.; Bilimoria, K.; Foster, C.; Gonzalex, R.; Sullivan, K.; Jackson, B.; Brazzel, J.; Hart, J.

2011-01-01

The Orion spacecraft was designed to rendezvous with multiple vehicles in low earth orbit (LEO) and beyond. To perform the required rendezvous and docking task, Orion must provide enough control authority to perform coarse translational maneuvers while maintaining precision to perform the delicate docking corrections. While Orion has autonomous docking capabilities, it is expected that final approach and docking operations with the International Space Station (ISS) will initially be performed in a manual mode. A series of evaluations was conducted by NASA and Lockheed Martin at the Johnson Space Center to determine the handling qualities (HQ) of the Orion spacecraft during different docking and rendezvous conditions using the Cooper-Harper scale. This paper will address the specifics of the handling qualities methodology, vehicle configuration, scenarios flown, data collection tools, and subject ratings and comments. The initial Orion HQ assessment examined Orion docking to the ISS. This scenario demonstrates the Translational Hand Controller (THC) handling qualities of Orion. During this initial assessment, two different scenarios were evaluated. The first was a nominal docking approach to a stable ISS, with Orion initializing with relative position dispersions and a closing rate of approximately 0.1 ft/sec. The second docking scenario was identical to the first, except the attitude motion of the ISS was modeled to simulate a stress case ( 1 degree deadband per axis and 0.01 deg/sec rate deadband per axis). For both scenarios, subjects started each run on final approach at a docking port-to-port range of 20 ft. Subjects used the THC in pulse mode with cues from the docking camera image, window views, and range and range rate data displayed on the Orion display units. As in the actual design, the attitude of the Orion vehicle was held by the automated flight control system at 0.5 degree deadband per axis. Several error sources were modeled including Reaction

Ground-to-Flight Handling Qualities Comparisons for a High Performance Airplane

NASA Technical Reports Server (NTRS)

Brandon, Jay M.; Glaab, Louis J.; Brown, Philip W.; Phillips, Michael R.

1995-01-01

A flight test program was conducted in conjunction with a ground-based piloted simulation study to enable a comparison of handling qualities ratings for a variety of maneuvers between flight and simulation of a modern high performance airplane. Specific objectives included an evaluation of pilot-induced oscillation (PIO) tendencies and a determination of maneuver types which result in either good or poor ground-to-flight pilot handling qualities ratings. A General Dynamics F-16XL aircraft was used for the flight evaluations, and the NASA Langley Differential Maneuvering Simulator was employed for the ground based evaluations. Two NASA research pilots evaluated both the airplane and simulator characteristics using tasks developed in the simulator. Simulator and flight tests were all conducted within approximately a one month time frame. Maneuvers included numerous fine tracking evaluations at various angles of attack, load factors and speed ranges, gross acquisitions involving longitudinal and lateral maneuvering, roll angle captures, and an ILS task with a sidestep to landing. Overall results showed generally good correlation between ground and flight for PIO tendencies and general handling qualities comments. Differences in pilot technique used in simulator evaluations and effects of airplane accelerations and motions are illustrated.

Microphone Handling Noise: Measurements of Perceptual Threshold and Effects on Audio Quality

PubMed Central

Kendrick, Paul; Jackson, Iain R.; Fazenda, Bruno M.; Cox, Trevor J.; Li, Francis F.

2015-01-01

A psychoacoustic experiment was carried out to test the effects of microphone handling noise on perceived audio quality. Handling noise is a problem affecting both amateurs using their smartphones and cameras, as well as professionals using separate microphones and digital recorders. The noises used for the tests were measured from a variety of devices, including smartphones, laptops and handheld microphones. The signal features that characterise these noises are analysed and presented. The sounds include various types of transient, impact noises created by tapping or knocking devices, as well as more sustained sounds caused by rubbing. During the perceptual tests, listeners auditioned speech podcasts and were asked to rate the degradation of any unwanted sounds they heard. A representative design test methodology was developed that tried to encourage everyday rather than analytical listening. Signal-to-noise ratio (SNR) of the handling noise events was shown to be the best predictor of quality degradation. Other factors such as noise type or background noise in the listening environment did not significantly affect quality ratings. Podcast, microphone type and reproduction equipment were found to be significant but only to a small extent. A model allowing the prediction of degradation from the SNR is presented. The SNR threshold at which 50% of subjects noticed handling noise was found to be 4.2 ± 0.6 dBA. The results from this work are important for the understanding of our perception of impact sound and resonant noises in recordings, and will inform the future development of an automated predictor of quality for handling noise. PMID:26473498

Handling qualities of large flexible control-configured aircraft

NASA Technical Reports Server (NTRS)

Swaim, R. L.

1979-01-01

The approach to an analytical study of flexible airplane longitudinal handling qualities was to parametrically vary the natural frequencies of two symmetric elastic modes to induce mode interactions with the rigid body dynamics. Since the structure of the pilot model was unknown for such dynamic interactions, the optimal control pilot modeling method is being applied and used in conjunction with pilot rating method.

Flight-testing and frequency-domain analysis for rotorcraft handling qualities

NASA Technical Reports Server (NTRS)

Ham, Johnnie A.; Gardner, Charles K.; Tischler, Mark B.

1995-01-01

A demonstration of frequency-domain flight-testing techniques and analysis was performed on a U.S. Army OH-58D helicopter in support of the OH-58D Airworthiness and Flight Characteristics Evaluation and of the Army's development and ongoing review of Aeronautical Design Standard 33C, Handling Qualities Requirements for Military Rotorcraft. Hover and forward flight (60 kn) tests were conducted in 1 flight hour by Army experimental test pilots. Further processing of the hover data generated a complete database of velocity, angular-rate, and acceleration-frequency responses to control inputs. A joint effort was then undertaken by the Airworthiness Qualification Test Dirtectorate and the U.S. Army Aeroflightdynamics Directorate to derive handling-quality information from the frequency-domain database using a variety of approaches. This report documents numerous results that have been obtained from the simple frequency-domain tests; in many areas, these results provide more insight into the aircraft dynmamics that affect handling qualities than do traditional flight tests. The handling-quality results include ADS-33C bandwidth and phase-delay calculations, vibration spectral determinations, transfer-function models to examine single-axis results, and a six-degree-of-freedom fully coupled state-space model. The ability of this model to accurately predict responses was verified using data from pulse inputs. This report also documents the frequency-sweep flight-test technique and data analysis used to support the tests.

Evaluation of High-Angle-of-Attack Handling Qualities for the X-31A Using Standard Evaluation Maneuvers

NASA Technical Reports Server (NTRS)

Stoliker, Patrick C.; Bosworth, John T.

1996-01-01

The X-31A aircraft gross-acquisition and fine-tracking handling qualities have been evaluated using standard evaluation maneuvers developed by Wright Laboratory, Wright-Patterson Air Force Base. The emphasis of the testing is in the angle-of-attack range between 30 deg and 70 deg. Longitudinal gross-acquisition handling qualities results show borderline Level 1/Level 2 performance. Lateral gross-acquisition testing results in Level 1/Level 2 ratings below 45 deg angle of attack, degrading into Level 3 as angle of attack increases. The fine-tracking performance in both longitudinal and lateral axes also receives Level 1 ratings near 30 deg angle of attack, with the ratings tending towards Level 3 at angles of attack greater than 50 deg. These ratings do not match the expectations from the extensive close-in combat testing where the X-31A aircraft demonstrated fair to good handling qualities maneuvering for high angles of attack. This paper presents the results of the high-angle-of-attack handling qualities flight testing of the X-31A aircraft. Discussion of the preparation for the maneuvers, the pilot ratings, and selected pilot comments are included. Evaluation of the results is made in conjunction with existing Neal-Smith, bandwidth, Smith-Geddes, and military specifications.

Evaluation of High-Angle-of-Attack Handling Qualities for the X-31A Using Standard Evaluation Maneuvers

NASA Technical Reports Server (NTRS)

Stoliker, Patrick C.; Bosworth, John T.

1997-01-01

The X-31A aircraft gross-acquisition and fine-tracking handling qualities have been evaluated using standard evaluation maneuvers developed by Wright Laboratory, Wright Patterson Air Force Base. The emphasis of the testing is in the angle-of-attack range between 30 deg. and 70 deg. Longitudinal gross-acquisition handling qualities results show borderline Level l/Level 2 performance. Lateral gross-acquisition testing results in Level l/Level 2 ratings below 45 deg. angle of attack, degrading into Level 3 as angle of attack increases. The fine tracking performance in both longitudinal and lateral axes also receives Level 1 ratings near 30 deg. angle of attack, with the ratings tending towards Level 3 at angles of attack greater than 50 deg. These ratings do not match the expectations from the extensive close-in combat testing where the X-31A aircraft demonstrated fair to good handling qualities maneuvering for high angles of attack. This paper presents the results of the high-angle-of-attack handling qualities flight testing of the X-31A aircraft. Discussion of the preparation for the maneuvers, the pilot ratings, and selected pilot comments are included. Evaluation of the results is made in conjunction with existing Neal Smith, bandwidth, Smith-Geddes, and military specifications.

Exploratory piloted simulator study of the effects of winglets on handling qualities of a representative agricultural airplane

NASA Technical Reports Server (NTRS)

Ogburn, M. E.; Brown, P. W.

1980-01-01

The effects on handling qualities of adding winglets to a representative agricultural aircraft configuration during swath-run maneuvering were evaluated. Aerodynamic data used in the simulation were based on low-speed wind tunnel tests of a full scale airplane and a subscale model. The Cooper-Harper handling qualities rating scale, supplementary pilot comments, and pilot vehicle performance data were used to describe the handling qualities of the airplane with the different wing-tip configurations. Results showed that the lateral-directional handling qualities of the airplane were greatly affected by the application of winglets and winglet cant angle. The airplane with winglets canted out 20 deg exhibited severely degraded lateral directional handling qualities in comparison to the basic airplane. When the winglets were canted inward 10 deg, the flying qualities of the configuration were markedly improved over those of the winglet-canted-out configuration or the basic configuration without winglets, indicating that proper tailoring of the winglet design may afford a potential benefit in the area of handling qualities.

Aircraft Handling Qualities Data

DTIC Science & Technology

1972-12-01

WITH YOUR INQUIRY 02672-931227121247 DEPT OF DEFENSE DEFENSE TECHNICAL INFORMATION CENTER ATTN: DTIC-OCP/JOYCE CHIRAS CAMERON STATION BLDG 9...Handling Qualities, F-IO4A, Lockheed Rept. t No. LR 10794, 12 Dec. 19ř Andrews, William H., and Herman A. Rediess, Flight-Determined Eta- bility and

Improved Lunar Lander Handling Qualities Through Control Response Type and Display Enhancements

NASA Technical Reports Server (NTRS)

Mueller, Eric Richard; Bilimoria, Karl D.; Frost, Chad Ritchie

2010-01-01

A piloted simulation that studied the handling qualities for a precision lunar landing task from final approach to touchdown is presented. A vehicle model based on NASA's Altair Lunar Lander was used to explore the design space around the nominal vehicle configuration to determine which combination of factors provides satisfactory pilot-vehicle performance and workload; details of the control and propulsion systems not available for that vehicle were derived from Apollo Lunar Module data. The experiment was conducted on a large motion base simulator. Eight Space Shuttle and Apollo pilot astronauts and three NASA test pilots served as evaluation pilots, providing Cooper-Harper ratings, Task Load Index ratings and qualitative comments. Each pilot flew seven combinations of control response types and three sets of displays, including two varieties of guidance and a nonguided approach. The response types included Rate Command with Attitude Hold, which was used in the original Apollo Moon landings, a Velocity Increment Command response type designed for up-and-away flight, three response types designed specifically for the vertical descent portion of the trajectory, and combinations of these. It was found that Velocity Increment Command significantly improved handling qualities when compared with the baseline Apollo design, receiving predominantly Level 1 ratings. This response type could be flown with or without explicit guidance cues, something that was very difficult with the baseline design, and resulted in approximately equivalent touchdown accuracies and propellant burn as the baseline response type. The response types designed to be used exclusively in the vertical descent portion of the trajectory did not improve handling qualities.

Ride quality sensitivity to SAS control law and to handling quality variations

NASA Technical Reports Server (NTRS)

Roberts, P. A.; Schmidt, D. K.; Swaim, R. L.

1976-01-01

The RQ trends which large flexible aircraft exhibit under various parameterizations of control laws and handling qualities are discussed. A summary of the assumptions and solution technique, a control law parameterization review, a discussion of ride sensitivity to handling qualities, and the RQ effects generated by implementing relaxed static stability configurations are included.

Flight testing and frequency domain analysis for rotorcraft handling qualities characteristics

NASA Technical Reports Server (NTRS)

Ham, Johnnie A.; Gardner, Charles K.; Tischler, Mark B.

1993-01-01

A demonstration of frequency domain flight testing techniques and analyses was performed on a U.S. Army OH-58D helicopter in support of the OH-58D Airworthiness and Flight Characteristics Evaluation and the Army's development and ongoing review of Aeronautical Design Standard 33C, Handling Qualities Requirements for Military Rotorcraft. Hover and forward flight (60 knots) tests were conducted in 1 flight hour by Army experimental test pilots. Further processing of the hover data generated a complete database of velocity, angular rate, and acceleration frequency responses to control inputs. A joint effort was then undertaken by the Airworthiness Qualification Test Directorate (AQTD) and the U.S. Army Aeroflightdynamics Directorate (AFDD) to derive handling qualities information from the frequency response database. A significant amount of information could be extracted from the frequency domain database using a variety of approaches. This report documents numerous results that have been obtained from the simple frequency domain tests; in many areas, these results provide more insight into the aircraft dynamics that affect handling qualities than to traditional flight tests. The handling qualities results include ADS-33C bandwidth and phase delay calculations, vibration spectral determinations, transfer function models to examine single axis results, and a six degree of freedom fully coupled state space model. The ability of this model to accurately predict aircraft responses was verified using data from pulse inputs. This report also documents the frequency-sweep flight test technique and data analysis used to support the tests.

Handling Qualities of a Capsule Spacecraft During Atmospheric Entry

NASA Technical Reports Server (NTRS)

Bilimoria, Karl D.; Mueller, Eric R.

2010-01-01

A piloted simulation was conducted to study handling qualities for capsule spacecraft entering the Earth s atmosphere. Eight evaluation pilots, including six pilot astronauts, provided Cooper-Harper ratings, workload ratings, and qualitative comments. The simulation began after descending through the atmospheric entry interface point and continued until the drogue parachutes deployed. There were two categories of piloting tasks, both of which required bank angle control. In one task category, the pilot followed a closed-loop bank angle command computed by the backup guidance system to manage g-loads during entry. In the other task category, the pilot used intuitive rules to determine the desired bank angle independently, based on an open-loop schedule of vertical speed, Mach, and total energy specified at several range-to-target gates along the entry trajectory. Pilots were able to accurately track the bank angle guidance commands and steered the capsule toward the recovery site with essentially the same range error as the benchmark autopilot trajectory albeit with substantially higher propellant usage, and the handling qualities for this task were satisfactory. Another key result was that the complex piloting task of atmospheric entry could be performed satisfactorily, even in the presence of large dispersions, by controlling bank angle to follow a simple open-loop schedule.

Evaluation of High-Speed Civil Transport Handling Qualities Criteria with Supersonic Flight Data

NASA Technical Reports Server (NTRS)

Cox, Timothy H.; Jackson, Dante W.

1997-01-01

Most flying qualities criteria have been developed from data in the subsonic flight regime. Unique characteristics of supersonic flight raise questions about whether these criteria successfully extend into the supersonic flight regime. Approximately 25 years ago NASA Dryden Flight Research Center addressed this issue with handling qualities evaluations of the XB-70 and YF-12. Good correlations between some of the classical handling qualities parameters, such as the control anticipation parameter as a function of damping, were discovered. More criteria have been developed since these studies. Some of these more recent criteria are being used in designing the High-Speed Civil Transport (HSCT). A second research study recently addressed this issue through flying qualities evaluations of the SR-71 at Mach 3. The research goal was to extend the high-speed flying qualities experience of large airplanes and to evaluate more recent MIL-STD-1797 criteria against pilot comments and ratings. Emphasis was placed on evaluating the criteria used for designing the HSCT. XB-70 and YF-12 data from the previous research supplemented the SR-71 data. The results indicate that the criteria used in the HSCT design are conservative and should provide good flying qualities for typical high-speed maneuvering. Additional results show correlation between the ratings and comments and criteria for gradual maneuvering with precision control. Correlation is shown between ratings and comments and an extension of the Neal/Smith criterion using normal acceleration instead of pitch rate.

Prediction of aircraft handling qualities using analytical models of the human pilot

NASA Technical Reports Server (NTRS)

Hess, R. A.

1982-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion for determining the susceptibility of an aircraft to pilot-induced oscillations (PIO) is formulated. Finally, a model-based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

Prediction of aircraft handling qualities using analytical models of the human pilot

NASA Technical Reports Server (NTRS)

Hess, R. A.

1982-01-01

The optimal control model (OCM) of the human pilot is applied to the study of aircraft handling qualities. Attention is focused primarily on longitudinal tasks. The modeling technique differs from previous applications of the OCM in that considerable effort is expended in simplifying the pilot/vehicle analysis. After briefly reviewing the OCM, a technique for modeling the pilot controlling higher order systems is introduced. Following this, a simple criterion for determining the susceptibility of an aircraft to pilot induced oscillations is formulated. Finally, a model based metric for pilot rating prediction is discussed. The resulting modeling procedure provides a relatively simple, yet unified approach to the study of a variety of handling qualities problems.

Flight simulator for hypersonic vehicle and a study of NASP handling qualities

NASA Technical Reports Server (NTRS)

Ntuen, Celestine A.; Park, Eui H.; Deeb, Joseph M.; Kim, Jung H.

1992-01-01

The research goal of the Human-Machine Systems Engineering Group was to study the existing handling quality studies in aircraft with sonic to supersonic speeds and power in order to understand information requirements needed for a hypersonic vehicle flight simulator. This goal falls within the NASA task statements: (1) develop flight simulator for hypersonic vehicle; (2) study NASP handling qualities; and (3) study effects of flexibility on handling qualities and on control system performance. Following the above statement of work, the group has developed three research strategies. These are: (1) to study existing handling quality studies and the associated aircraft and develop flight simulation data characterization; (2) to develop a profile for flight simulation data acquisition based on objective statement no. 1 above; and (3) to develop a simulator and an embedded expert system platform which can be used in handling quality experiments for hypersonic aircraft/flight simulation training.

Unified Theory for Aircraft Handling Qualities and Adverse Aircraft-Pilot Coupling

NASA Technical Reports Server (NTRS)

Hess, R. A.

1997-01-01

A unified theory for aircraft handling qualities and adverse aircraft-pilot coupling or pilot-induced oscillations is introduced. The theory is based on a structural model of the human pilot. A methodology is presented for the prediction of (1) handling qualities levels; (2) pilot-induced oscillation rating levels; and (3) a frequency range in which pilot-induced oscillations are likely to occur. Although the dynamics of the force-feel system of the cockpit inceptor is included, the methodology will not account for effects attributable to control sensitivity and is limited to single-axis tasks and, at present, to linear vehicle models. The theory is derived from the feedback topology of the structural model and an examination of flight test results for 32 aircraft configurations simulated by the U.S. Air Force/CALSPAN NT-33A and Total In-Flight Simulator variable stability aircraft. An extension to nonlinear vehicle dynamics such as that encountered with actuator saturation is discussed.

Effects of simulated turbulence on aircraft handling qualities

NASA Technical Reports Server (NTRS)

Jacobson, I. D.; Joshi, D. S.

1977-01-01

The influence of simulated turbulence on aircraft handling qualities is presented. Pilot opinions of the handling qualities of a light general aviation aircraft were evaluated in a motion-base simulator using a simulated turbulence environment. A realistic representation of turbulence disturbances is described in terms of rms intensity and scale length and their random variations with time. The time histories generated by the proposed turbulence models showed characteristics which are more similar to real turbulence than the frequently-used Gaussian turbulence model. The proposed turbulence models flexibly accommodate changes in atmospheric conditions and are easily implemented in flight simulator studies.

High-Alpha Handling Qualities Flight Research on the NASA F/A-18 High Alpha Research Vehicle

NASA Technical Reports Server (NTRS)

Wichman, Keith D.; Pahle, Joseph W.; Bahm, Catherine; Davidson, John B.; Bacon, Barton J.; Murphy, Patrick C.; Ostroff, Aaron J.; Hoffler, Keith D.

1996-01-01

A flight research study of high-angle-of-attack handling qualities has been conducted at the NASA Dryden Flight Research Center using the F/A-18 High Alpha Research Vehicle (HARV). The objectives were to create a high-angle-of-attack handling qualities flight database, develop appropriate research evaluation maneuvers, and evaluate high-angle-of-attack handling qualities guidelines and criteria. Using linear and nonlinear simulations and flight research data, the predictions from each criterion were compared with the pilot ratings and comments. Proposed high-angle-of-attack nonlinear design guidelines and proposed handling qualities criteria and guidelines developed using piloted simulation were considered. Recently formulated time-domain Neal-Smith guidelines were also considered for application to high-angle-of-attack maneuvering. Conventional envelope criteria were evaluated for possible extension to the high-angle-of-attack regime. Additionally, the maneuvers were studied as potential evaluation techniques, including a limited validation of the proposed standard evaluation maneuver set. This paper gives an overview of these research objectives through examples and summarizes result highlights. The maneuver development is described briefly, the criteria evaluation is emphasized with example results given, and a brief discussion of the database form and content is presented.

Effects of side-stick controllers on rotorcraft handling qualities for terrain flight

NASA Technical Reports Server (NTRS)

Aiken, E. W.

1985-01-01

Pertinent fixed and rotary-wing feasibility studies and handling-qualities research programs are reviewed and the effects of certain controller characteristics on handling qualities for specific rotorcraft flight tasks are summarized. The effects of the controller force-deflection relationship and the number of controlled axes that are integrated in a single controller are examined. Simulation studies were conducted which provide a significant part of the available handling qualities data. The studies demonstrate the feasibility of using a single, properly designed, limited-displacement, multiaxis controller for certain relatively routine flight tasks in a two-crew rotorcraft with nominal levels of stability and control augmentation with a high degree of reliability are incorporated, separated three or two-axis controller configurations are required for acceptable handling qualities.

The Implications of Handling Qualities in Civil Helicopter Accidents Involving Hover and Low Speed Flight

NASA Technical Reports Server (NTRS)

Dugan, Daniel C.; Delamer, Kevin J.

2005-01-01

Because of increasing accident rates in Army helicopters in hover and low speed flight, a study was made in 1999 of accidents which could be attributed to inadequate stability augmentation. A study of civil helicopter accidents from 1993-2004 was then undertaken to pursue the issue of poor handling qualities in helicopters which, in almost all cases, had no stability augmentation. The vast majority of the mishaps studied occurred during daylight in visual meteorological condition, reducing the impact of degraded visual environments (DVE) on the results. Based on the Cooper-Harper Rating Scale, the handling qualities of many of the helicopters studied could be described as having from "very objectionable" to "major" deficiencies. These costly deficiencies have resulted in unnecessary loss of life, injury, and high dollar damage. Low cost and lightweight augmentation systems for helicopters have been developed in the past and are still being investigated. They offer the potential for significant reductions in the accident rate.

Handling qualities of large flexible control-configured aircraft

NASA Technical Reports Server (NTRS)

Swaim, R. L.

1980-01-01

The effects on handling qualities of low frequency symmetric elastic mode interaction with the rigid body dynamics of a large flexible aircraft was analyzed by use of a mathematical pilot modeling computer simulation. An extension of the optimal control model for a human pilot was made so that the mode interaction effects on the pilot's control task could be assessed. Pilot ratings were determined for a longitudinal tracking task with parametric variations in the undamped natural frequencies of the two lowest frequency symmetric elastic modes made to induce varying amounts of mode interaction. Relating numerical performance index values associated with the frequency variations used in several dynamic cases, to a numerical Cooper-Harper pilot rating has proved successful in discriminating when the mathematical pilot can or cannot separate rigid from elastic response in the tracking task.

A Look at Handling Qualities of Canard Configurations

NASA Technical Reports Server (NTRS)

Anderson, Seth B.

1986-01-01

The first human-powered flight was achieved by a canard-configured aircraft (Wright Brothers). Although other canard concepts were flown with varying degrees of success over the years, the tail-aft configuration has dominated the aircraft market for both military and civil use. Reviewed are the development of several canard aircraft with emphasis on stability and control, handling qualities, and operating problems. The results show that early canard concepts suffered adversely in flight behavior because of a lack of understanding of the sensitivities of these concepts to basic stability and control principles. Modern canard designs have been made competitive with tail-aft configurations by using appropriate handling qualities design criteria.

Investigation of the effects of bandwidth and time delay on helicopter roll-axis handling qualities

NASA Technical Reports Server (NTRS)

Pausder, Heinz-Juergen; Blanken, Chris L.

1992-01-01

Several years of cooperative research conducted under the U.S./German Memorandum of Understanding (MOU) in helicopter flight control has recently resulted in a successful handling qualities study. The focus of this cooperative research has been the effects on handling qualities due to time delays in combination with a high bandwidth vehicle. The jointly performed study included the use of U.S. ground-based simulation and German in-flight simulation facilities. The NASA-Ames Vertical Motion Simulator (VMS) was used to develop a high bandwidth slalom tracking task which took into consideration the constraints of the facilities. The VMS was also used to define a range of the test parameters and to perform initial handling qualities evaluations. The flight tests were conducted using DLR's variable-stability BO 105 S3 Advanced Technology Testing Helicopter System (ATTHeS). Configurations included a rate command and an attitude command response system with added time delays up to 160 milliseconds over the baseline and bandwidth values between 1.5 and 4.5 rad/sec. Sixty-six evaluations were performed in about 25 hr of flight time during 10 days of testing. The results indicate a need to more tightly constrain the allowable roll axis phase delay for the Level 1 and Level 2 requirements in the U.S. Army's specification for helicopter handling qualities, ADS-33C.

Investigation of the effects of bandwidth and time delay on helicopter roll-axis handling qualities

NASA Technical Reports Server (NTRS)

Blanken, Chris L.; Pausder, Heinz-Jurgen

1994-01-01

Several years of cooperative research conducted under the U.S./German Memorandum of Understanding (MOU) in helicopter aeromechanics have recently resulted in a successful handling qualities study. The focus of this cooperative research has been the effect of time delays in a high bandwidth vehicle on handling qualities. The jointly performed study included the use of U.S. ground-based simulation and German in-flight simulation facilities. The NASA-Ames Vertical Motion Simulator (VMS) was used to develop a high bandwidth slalom tracking task which took into consideration the constraints of the facilities. The VMS was used to define a range of the test parameters and to perform initial handling qualities evaluations. The flight tests were conducted using DLR's variable-stability BO 105 S3 Advanced Technology Testing Helicopter System (ATTHeS). Configurations included a rate command and an attitude command response system with added time delays of up to 160 milliseconds over the baseline and band width values between 1.5 and 4.5 rad/sec. Sixty-six evaluations were performed in about 25 hours of flight time during ten days of testing. The results indicate a need to more tightly constrain the allowable roll axis phase delay for the Level 1 and Level 2 requirements in the U.S. Army's specification for helicopter handling qualities Aeronautical Design Standard (ADS)-33C.

Investigation of the effects of bandwidth and time delay on helicopter roll-axis handling qualities

NASA Technical Reports Server (NTRS)

Pausder, Heinz-Juergen; Blanken, Chris L.

1993-01-01

Several years of cooperative research conducted under the U.S./German Memorandum of Understanding (MOU) in helicopter flight control has recently resulted in a successful handling qualities study. The focus of this cooperative research has been the effects on handling qualities due to time delays in combination with a high bandwidth vehicle. The jointly performed study included the use of U.S. ground-based simulation and German in-flight simulation facilities. The NASA-Ames Vertical Motion Simulator (VMS) was used to develop a high bandwidth slalom tracking task which took into consideration the constraints of the facilities. The VMS was also used to define a range of the test parameters and to perform initial handling qualities evaluations. The flight tests were conducted using DLR's variable-stability BO 105 S3 Advanced Technology Testing Helicopter System (ATTHeS). Configurations included a rate command and an attitude command response system with added time delays up to 160 milliseconds over the baseline and bandwidth values between 1.5 and 4.5 rad/sec. Sixty-six evaluations were performed in about 25 hours of flight time during ten days of testing. The results indicate a need to more tightly constrain the allowable roll axis phase delay for the Level 1 and Level 2 requirements in the U.S. Army's specification for helicopter handling qualities, ADS-33C.

Investigation of Control System and Display Variations on Spacecraft Handling Qualities for Docking with Stationary and Rotating Targets

NASA Technical Reports Server (NTRS)

Jackson, E. Bruce; Goodrich, Kenneth H.; Bailey, Randall E.; Barnes, James R.; Ragsdale, William A.; Neuhaus, Jason R.

2010-01-01

This paper documents the investigation into the manual docking of a preliminary version of the Crew Exploration Vehicle with stationary and rotating targets in Low Earth Orbit. The investigation was conducted at NASA Langley Research Center in the summer of 2008 in a repurposed fixed-base transport aircraft cockpit and involved nine evaluation astronauts and research pilots. The investigation quantified the benefits of a feed-forward reaction control system thruster mixing scheme to reduce translation-into-rotation coupling, despite unmodeled variations in individual thruster force levels and off-axis center of mass locations up to 12 inches. A reduced rate dead-band in the phase-plane attitude controller also showed some promise. Candidate predictive symbology overlaid on a docking ring centerline camera image did not improve handling qualities, but an innovative attitude status indicator symbol was beneficial. The investigation also showed high workload and handling quality problems when manual dockings were performed with a rotating target. These concerns indicate achieving satisfactory handling quality ratings with a vehicle configuration similar to the nominal Crew Exploration Vehicle may require additional automation.

A pilot modeling technique for handling-qualities research

NASA Technical Reports Server (NTRS)

Hess, R. A.

1980-01-01

A brief survey of the more dominant analysis techniques used in closed-loop handling-qualities research is presented. These techniques are shown to rely on so-called classical and modern analytical models of the human pilot which have their foundation in the analysis and design principles of feedback control. The optimal control model of the human pilot is discussed in some detail and a novel approach to the a priori selection of pertinent model parameters is discussed. Frequency domain and tracking performance data from 10 pilot-in-the-loop simulation experiments involving 3 different tasks are used to demonstrate the parameter selection technique. Finally, the utility of this modeling approach in handling-qualities research is discussed.

Aircraft model prototypes which have specified handling-quality time histories

NASA Technical Reports Server (NTRS)

Johnson, S. H.

1976-01-01

Several techniques for obtaining linear constant-coefficient airplane models from specified handling-quality time histories are discussed. One technique, the pseudodata method, solves the basic problem, yields specified eigenvalues, and accommodates state-variable transfer-function zero suppression. The method is fully illustrated for a fourth-order stability-axis small-motion model with three lateral handling-quality time histories specified. The FORTRAN program which obtains and verifies the model is included and fully documented.

Application of frequency domain handling qualities criteria to the longitudinal landing task

NASA Technical Reports Server (NTRS)

Sarrafian, S. K.; Powers, B. G.

1985-01-01

Three frequency-domain handling qualities criteria have been applied to the observed data to correlate the actual pilot ratings assigned to generic transport configurations with stability augmentation during the longitudinal landing task. The criteria are based on closed-loop techniques using pitch attitude, altitude rate at the pilot station, and altitude at the pilot station as dominating control parameters during this task. It is found that most promising results are obtained with altitude control performed by closing an inner loop on pitch attitude and closing an outer loop on altitude.

Handling Qualities Evaluation of Pilot Tools for Spacecraft Docking in Earth Orbit

NASA Technical Reports Server (NTRS)

Bilimoria, Karl D.; Mueller, Eric; Frost, Chad

2009-01-01

A new generation of spacecraft is now under development by NASA to replace the Space Shuttle and return astronauts to the Moon. These spacecraft will have a manual control capability for several mission tasks, and the ease and precision with which pilots can execute these tasks will have an important effect on mission risk and training costs. This paper focuses on the handling qualities of a spacecraft based on dynamics similar to that of the Crew Exploration Vehicle, during the last segment of the docking task with a space station in low Earth orbit. A previous study established that handling qualities for this task degrade significantly as the level of translation-into-rotation coupling increases. The goal of this study is to evaluate the efficacy of various pilot aids designed to mitigate the handling qualities degradation caused by this coupling. Four pilot tools were ev adluaetead:d-band box/indicator, flight-path marker, translation guidance cues, and feed-forward control. Each of these pilot tools improved handling qualities, generally with greater improvements resulting from using these tools in combination. A key result of this study is that feedforward control effectively counteracts coupling effects, providing solid Level 1 handling qualities for the spacecraft configuration evaluated.

Subsonic Wing Optimization for Handling Qualities Using ACSYNT

NASA Technical Reports Server (NTRS)

Soban, Danielle Suzanne

1996-01-01

The capability to accurately and rapidly predict aircraft stability derivatives using one comprehensive analysis tool has been created. The PREDAVOR tool has the following capabilities: rapid estimation of stability derivatives using a vortex lattice method, calculation of a longitudinal handling qualities metric, and inherent methodology to optimize a given aircraft configuration for longitudinal handling qualities, including an intuitive graphical interface. The PREDAVOR tool may be applied to both subsonic and supersonic designs, as well as conventional and unconventional, symmetric and asymmetric configurations. The workstation-based tool uses as its model a three-dimensional model of the configuration generated using a computer aided design (CAD) package. The PREDAVOR tool was applied to a Lear Jet Model 23 and the North American XB-70 Valkyrie.

Development and perceived effects of an educational programme on quality and safety in medication handling in residential facilities.

PubMed

Mygind, Anna; El-Souri, Mira; Rossing, Charlotte; Thomsen, Linda Aagaard

2018-04-01

To develop and test an educational programme on quality and safety in medication handling for staff in residential facilities for the disabled. The continuing pharmacy education instructional design model was used to develop the programme with 22 learning objectives on disease and medicines, quality and safety, communication and coordination. The programme was a flexible, modular seven + two days' course addressing quality and safety in medication handling, disease and medicines, and medication supervision and reconciliation. The programme was tested in five Danish municipalities. Municipalities were selected based on their application for participation; each independently selected a facility for residents with mental and intellectual disabilities, and a facility for residents with severe mental illnesses. Perceived effects were measured based on a questionnaire completed by participants before and after the programme. Effects on motivation and confidence as well as perceived effects on knowledge, skills and competences related to medication handling, patient empowerment, communication, role clarification and safety culture were analysed conducting bivariate, stratified analyses and test for independence. Of the 114 participants completing the programme, 75 participants returned both questionnaires (response rate = 66%). Motivation and confidence regarding quality and safety in medication handling significantly improved, as did perceived knowledge, skills and competences on 20 learning objectives on role clarification, safety culture, medication handling, patient empowerment and communication. The programme improved staffs' motivation and confidence and their perceived ability to handle residents' medication safely through improved role clarification, safety culture, medication handling and patient empowerment and communication skills. © 2017 Royal Pharmaceutical Society.

Aircraft model prototypes which have specified handling-quality time histories

NASA Technical Reports Server (NTRS)

Johnson, S. H.

1978-01-01

Several techniques for obtaining linear constant-coefficient airplane models from specified handling-quality time histories are discussed. The pseudodata method solves the basic problem, yields specified eigenvalues, and accommodates state-variable transfer-function zero suppression. The algebraic equations to be solved are bilinear, at worst. The disadvantages are reduced generality and no assurance that the resulting model will be airplane like in detail. The method is fully illustrated for a fourth-order stability-axis small motion model with three lateral handling quality time histories specified. The FORTRAN program which obtains and verifies the model is included and fully documented.

A simulation investigation of the effects of engine-and thrust-response characteristics on helicopter handling qualities

NASA Technical Reports Server (NTRS)

Corless, L. D.; Blanken, C. L.

1983-01-01

A multi-phase program is being conducted to study, in a generic sense and through ground simulation, the effects of engine response, rotor inertia, rpm control, excess power, and vertical damping on specific maneuvers included in nap-of-the-Earth (NOE) operations. The helicopter configuration with an rpm-governed gas-turbine engine are considered. Handling-qualities-criteria data are considered in light of aspects peculiar to rotary-wing and NOE operations. The results of three moving-based piloted simulation studies are summarized and the frequency, characteristics of the helicopter thrust response which set it apart from other VTOL types are explained. Power-system response is affected by both the engine-governor response and the level of rotor inertia. However, results indicate that with unlimited power, variations in engine response can have a significant effect on pilot rating, whereas changes in rotor inertia, in general, do not. The results also show that any pilot interaction required to maintain proper control can significantly degrade handling qualities. Data for variations in vertical damping and collective sensitivity are compared with existing handling-qualities specifications, MIL-F-83300 and AGARD 577, and show a need for higher minimums for both damping and sensitivity for the bob-up task. Results for cases of limited power are also shown.

A compilation and analysis of helicopter handling qualities data. Volume 2: Data analysis

NASA Technical Reports Server (NTRS)

Heffley, R. K.

1979-01-01

A compilation and an analysis of helicopter handling qualities data are presented. Multiloop manual control methods are used to analyze the descriptive data, stability derivatives, and transfer functions for a six degrees of freedom, quasi static model. A compensatory loop structure is applied to coupled longitudinal, lateral and directional equations in such a way that key handling qualities features are examined directly.

A design procedure for the handling qualities optimization of the X-29A aircraft

NASA Technical Reports Server (NTRS)

Bosworth, John T.; Cox, Timothy H.

1989-01-01

A design technique for handling qualities improvement was developed for the X-29A aircraft. As with any new aircraft, the X-29A control law designers were presented with a relatively high degree of uncertainty in their mathematical models. The presence of uncertainties, and the high level of static instability of the X-29A caused the control law designers to stress stability and robustness over handling qualities. During flight test, the mathematical models of the vehicle were validated or corrected to match the vehicle dynamic behavior. The updated models were then used to fine tune the control system to provide fighter-like handling characteristics. A design methodology was developed which works within the existing control system architecture to provide improved handling qualities and acceptable stability with a minimum of cost in both implementation as well as software verification and validation.

Handling Qualities of Large Rotorcraft in Hover and Low Speed

NASA Technical Reports Server (NTRS)

Malpica, Carlos; Theodore, Colin R.; Lawrence , Ben; Blanken, Chris L.

2015-01-01

According to a number of system studies, large capacity advanced rotorcraft with a capability of high cruise speeds (approx.350 mph) as well as vertical and/or short take-off and landing (V/STOL) flight could alleviate anticipated air transportation capacity issues by making use of non-primary runways, taxiways, and aprons. These advanced aircraft pose a number of design challenges, as well as unknown issues in the flight control and handling qualities domains. A series of piloted simulation experiments have been conducted on the NASA Ames Research Center Vertical Motion Simulator (VMS) in recent years to systematically investigate the fundamental flight control and handling qualities issues associated with the characteristics of large rotorcraft, including tiltrotors, in hover and low-speed maneuvering.

Structural dynamic model obtained from flight use with piloted simulation and handling qualities analysis

NASA Technical Reports Server (NTRS)

Powers, Bruce G.

1996-01-01

The ability to use flight data to determine an aircraft model with structural dynamic effects suitable for piloted simulation. and handling qualities analysis has been developed. This technique was demonstrated using SR-71 flight test data. For the SR-71 aircraft, the most significant structural response is the longitudinal first-bending mode. This mode was modeled as a second-order system, and the other higher order modes were modeled as a time delay. The distribution of the modal response at various fuselage locations was developed using a uniform beam solution, which can be calibrated using flight data. This approach was compared to the mode shape obtained from the ground vibration test, and the general form of the uniform beam solution was found to be a good representation of the mode shape in the areas of interest. To calibrate the solution, pitch-rate and normal-acceleration instrumentation is required for at least two locations. With the resulting structural model incorporated into the simulation, a good representation of the flight characteristics was provided for handling qualities analysis and piloted simulation.

Inverse simulation system for evaluating handling qualities during rendezvous and docking

NASA Astrophysics Data System (ADS)

Zhou, Wanmeng; Wang, Hua; Thomson, Douglas; Tang, Guojin; Zhang, Fan

2017-08-01

The traditional method used for handling qualities assessment of manned space vehicles is too time-consuming to meet the requirements of an increasingly fast design process. In this study, a rendezvous and docking inverse simulation system to assess the handling qualities of spacecraft is proposed using a previously developed model-predictive-control architecture. By considering the fixed discrete force of the thrusters of the system, the inverse model is constructed using the least squares estimation method with a hyper-ellipsoidal restriction, the continuous control outputs of which are subsequently dispersed by pulse width modulation with sensitivity factors introduced. The inputs in every step are deemed constant parameters, and the method could be considered as a general method for solving nominal, redundant, and insufficient inverse problems. The rendezvous and docking inverse simulation is applied to a nine-degrees-of-freedom platform, and a novel handling qualities evaluation scheme is established according to the operation precision and astronauts' workload. Finally, different nominal trajectories are scored by the inverse simulation and an established evaluation scheme. The scores can offer theoretical guidance for astronaut training and more complex operation missions.

In Flight Evaluation of Active Inceptor Force-Feel Characteristics and Handling Qualities

NASA Technical Reports Server (NTRS)

Lusardi, Jeff A.; Blanken, Chris L.; Ott, Carl Raymond; Malpica, Carlos A.; von Gruenhagen, Wolfgang

2012-01-01

The effect of inceptor feel-system characteristics on piloted handling qualities has been a research topic of interest for many years. Most of the research efforts have focused on advanced fly-by-wire fixed-wing aircraft with only a few studies investigating the effects on rotorcraft. Consequently, only limited guidance is available on how cyclic force-feel characteristics should be set to obtain optimal handling qualities for rotorcraft. To study this effect, the U.S. Army Aeroflightdynamics Directorate working with the DLR Institute of Flight Systems in Germany under Task X of the U.S. German Memorandum of Understanding have been conducting flight test evaluations. In the U.S., five experimental test pilots have completed evaluations of two Mission Task Elements (MTEs) from ADS-33E-PRF and two command/response types for a matrix of center-stick cyclic force-feel characteristics at Moffett Field. In Germany, three experimental test Pilots have conducted initial evaluations of the two MTEs with two command/response types for a parallel matrix of side-stick cyclic force-feel characteristics at WTD-61 in Manching. The resulting data set is used to correlate the effect of changes in natural frequency and damping ratio of the cyclic inceptor on the piloted handling qualities. Existing criteria in ADS-33E and a proposed Handling Qualities Sensitivity Function that includes the effects of the cyclic force-feel characteristics are also evaluated against the data set and discussed.

Handling qualities related to stall/spin accidents of supersonic fighter aircraft

NASA Technical Reports Server (NTRS)

Anderson, S. B.

1984-01-01

This paper reviews the handling qualities which influence the high angle of attack (AOA) behavior of supersonic fighter aircraft in order to obtain a clearer understanding of the causes of stall/spin accidents. The results show that, because modern fighters suffer more serious consequences when control is lost, good handling qualities are essential for safe operation at high AOA. Relaxed static stability used on some fighter aircraft can result in control problems at high AOA owing to inertia coupling and the difficulty of a recovery from a deep stall. Indications are that the use of departure/spin resistance and an automatic spin prevention system will greatly improve the safety record for modern supersonic fighters.

Development of longitudinal handling qualities criteria for large advanced supersonic aircraft

NASA Technical Reports Server (NTRS)

Sudderth, R. W.; Bohn, J. G.; Caniff, M. A.; Bennett, G. R.

1975-01-01

Longitudinal handling qualities criteria in terms of airplane response characteristics were developed. The criteria cover high speed cruise maneuvering, landing approach, and stall recovery. Data substantiating the study results are reported.

Effects of simulator motion and visual characteristics on rotorcraft handling qualities evaluations

NASA Technical Reports Server (NTRS)

Mitchell, David G.; Hart, Daniel C.

1993-01-01

The pilot's perceptions of aircraft handling qualities are influenced by a combination of the aircraft dynamics, the task, and the environment under which the evaluation is performed. When the evaluation is performed in a groundbased simulator, the characteristics of the simulation facility also come into play. Two studies were conducted on NASA Ames Research Center's Vertical Motion Simulator to determine the effects of simulator characteristics on perceived handling qualities. Most evaluations were conducted with a baseline set of rotorcraft dynamics, using a simple transfer-function model of an uncoupled helicopter, under different conditions of visual time delays and motion command washout filters. Differences in pilot opinion were found as the visual and motion parameters were changed, reflecting a change in the pilots' perceptions of handling qualities, rather than changes in the aircraft model itself. The results indicate a need for tailoring the motion washout dynamics to suit the task. Visual-delay data are inconclusive but suggest that it may be better to allow some time delay in the visual path to minimize the mismatch between visual and motion, rather than eliminate the visual delay entirely through lead compensation.

Efficient halal bleeding, animal handling, and welfare: A holistic approach for meat quality.

PubMed

Aghwan, Z A; Bello, A U; Abubakar, A A; Imlan, J C; Sazili, A Q

2016-11-01

Traditional halal slaughter and other forms of religious slaughter are still an issue of debate. Opposing arguments related to pre-slaughter handling, stress and pain associated with restraint, whether the incision is painful or not, and the onset of unconsciousness have been put forward, but no consensus has been achieved. There is a need to strike a balance between halal bleeding in the light of science and animal welfare. There is a paucity of scientific data with respect to animal welfare, particularly the use of restraining devices, animal handling, and efficient halal bleeding. However, this review found that competent handling of animals, proper use of restraining devices, and the efficient bleeding process that follows halal slaughter maintains meat eating quality. In conclusion, halal bleeding, when carried out in accordance with recommended animal welfare procedures, will not only maintain the quality and wholesomeness of meat but could also potentially reduce suffering and pain. Maintained meat quality increases consumer satisfaction and food safety. Copyright © 2016. Published by Elsevier Ltd.

Handling Qualities Prediction of an F-16XL-Based Reduced Sonic Boom Aircraft

NASA Technical Reports Server (NTRS)

Cogan, Bruce; Yoo, Seung

2010-01-01

A major goal of the Supersonics Project under NASA s Fundamental Aeronautics program is sonic boom reduction of supersonic aircraft. An important part of this effort is development and validation of sonic boom prediction tools used in aircraft design. NASA Dryden s F- 16XL was selected as a potential testbed aircraft to provide flight validation. Part of this task was predicting the handling qualities of the modified aircraft. Due to the high cost of modifying the existing F-16XL control laws, it was desirable to find modifications that reduced the aircraft sonic boom but did not degrade baseline aircraft handling qualities allowing for the potential of flight test without changing the current control laws. This was not a requirement for the initial modification design work, but an important consideration for proceeding to the flight test option. The primary objective of this work was to determine an aerodynamic and mass properties envelope of the F-16XL aircraft. The designers could use this envelope to determine the effect of proposed modifications on aircraft handling qualities.

Effects of gut passage, feces, and seed handling on latency and rate of germination in seeds consumed by capuchins (Cebus capucinus).

PubMed

Valenta, Kim; Fedigan, Linda M

2009-04-01

One of the key measures of the effectiveness of primary seed dispersal by animals is the quality of seed dispersal (Schupp: Plant Ecol 107/108 [1993] 15-29). We present data on quality of seed dispersal by two groups of white-faced capuchins (Cebus capucinus) in Costa Rica to test the hypothesis that capuchin seed handling results in effective primary dispersal for some fruit species they consume. We examined seed handling for 27 plant species, and germination rates of 18 species consumed by capuchins. For five of the most commonly swallowed seed species, we determined germination rates and average time to germination (latency) for seeds ingested and defecated by capuchins and compared these to seeds removed directly from fruit and planted. For the same five species, we compared germination rates and latency for passed seeds planted in capuchin feces to those cleaned of feces and planted in soil. For three of five species, differences in proportion of germinated seeds were significantly higher for gut passed seeds than for controls. For four of five species, germination latency was significantly faster for gut passed seeds than for controls. Feces had either no effect on seed germination rate or precluded germination. Data presented here support the hypothesis that white-faced capuchins are effective primary dispersers.

Dynamic stability and handling qualities tests on a highly augmented, statically unstable airplane

NASA Technical Reports Server (NTRS)

Gera, Joseph; Bosworth, John T.

1987-01-01

Novel flight test and analysis techniques in the flight dynamics and handling qualities area are described. These techniques were utilized at NASA Ames-Dryden during the initial flight envelope clearance of the X-29A aircraft. It is shown that the open-loop frequency response of an aircraft with highly relaxed static stability can be successfully computed on the ground from telemetry data. Postflight closed-loop frequency response data were obtained from pilot-generated frequency sweeps and it is found that the current handling quality requirements for high-maneuverability aircraft are generally applicable to the X-29A.

Handling qualities criteria for the space shuttle orbiter during the terminal phase of flight

NASA Technical Reports Server (NTRS)

Stapleford, R. L.; Klein, R. H.; Hob, R. H.

1972-01-01

It was found that large portions of the military handling qualities specification are directly applicable. However a number of additional and substitute criteria are recommended for areas not covered or inadequately covered in the military specification. Supporting pilot/vehicle analyses and simulation experiments were conducted and are described. Results are also presented of analytical and simulator evaluations of three specific interim Orbiter designs which provided a test of the proposed handling qualities criteria. The correlations between the analytical and experimental evaluations were generally excellent.

Handling Qualities Specifications for U.S. Military Helicopters

NASA Technical Reports Server (NTRS)

Key, David L.

1982-01-01

Inadequacies in the military specification for helicopter handling qualities, MIL-H-8501A, have long been recognized, and the latest procurements by the U.S. Army used special Prime Item Development Specifications (PIDS). This paper assesses the efficacy of these PIDS and suggests that changes should be made. In particular, the structure developed in MIL-F-8785B (ASG) (the specification for flying qualities of piloted airplanes) should be incorporated. Improved requirements must be based on a systematic data base and concentrated on topics most important in preliminary design: static and dynamic stability, control power and sensitivity, and interaction with controllers and displays. Emphasis should be on current military helicopter missions and helicopter idiosyncrasies such as cross-coupling, nonlinearities, and higher-order dynamics.

76 FR 7096 - Minimum Quality and Handling Standards for Domestic and Imported Peanuts Marketed in the United...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-09

...). Accordingly, AMS published a notice of review and request for written comments on the Standards in the April...; FV10-996-610 Review] Minimum Quality and Handling Standards for Domestic and Imported Peanuts Marketed... the Minimum Quality and Handling Standards for Domestic and Imported Peanuts Marketed in the United...

Effects of rotor parameter variations on handling qualities of unaugmented helicopters in simulated terrain flight

NASA Technical Reports Server (NTRS)

Talbot, P. D.; Dugan, D. D.; Chen, R. T. N.; Gerdes, R. M.

1980-01-01

A coordinated analysis and ground simulator experiment was performed to investigate the effects on single rotor helicopter handling qualities of systematic variations in the main rotor hinge restraint, hub hinge offset, pitch-flap coupling, and blade lock number. Teetering rotor, articulated rotor, and hingeless rotor helicopters were evaluated by research pilots in special low level flying tasks involving obstacle avoidance at 60 to 100 knots airspeed. The results of the experiment are in the form of pilot ratings, pilot commentary, and some objective performance measures. Criteria for damping and sensitivity are reexamined when combined with the additional factors of cross coupling due to pitch and roll rates, pitch coupling with collective pitch, and longitudinal static stability. Ratings obtained with and without motion are compared. Acceptable flying qualities were obtained within each rotor type by suitable adjustment of the hub parameters, however, pure teetering rotors were found to lack control power for the tasks. A limit for the coupling parameter L sub q/L sub p of 0.35 is suggested.

An Investigation of Large Tilt-Rotor Short-Term Attitude Response Handling Qualities Requirements in Hover

NASA Technical Reports Server (NTRS)

Malcipa, Carlos; Decker, William A.; Theodore, Colin R.; Blanken, Christopher L.; Berger, Tom

2010-01-01

A piloted simulation investigation was conducted using the NASA Ames Vertical Motion Simulator to study the impact of pitch, roll and yaw attitude bandwidth and phase delay on handling qualities of large tilt-rotor aircraft. Multiple bandwidth and phase delay pairs were investigated for each axis. The simulation also investigated the effect that the pilot offset from the center of gravity has on handling qualities. While pilot offset does not change the dynamics of the vehicle, it does affect the proprioceptive and visual cues and it can have an impact on handling qualities. The experiment concentrated on two primary evaluation tasks: a precision hover task and a simple hover pedal turn. Six pilots flew over 1400 data runs with evaluation comments and objective performance data recorded. The paper will describe the experiment design and methodology, discuss the results of the experiment and summarize the findings.

Handling Qualities of Model Reference Adaptive Controllers with Varying Complexity for Pitch-Roll Coupled Failures

NASA Technical Reports Server (NTRS)

Schaefer, Jacob; Hanson, Curt; Johnson, Marcus A.; Nguyen, Nhan

2011-01-01

Three model reference adaptive controllers (MRAC) with varying levels of complexity were evaluated on a high performance jet aircraft and compared along with a baseline nonlinear dynamic inversion controller. The handling qualities and performance of the controllers were examined during failure conditions that induce coupling between the pitch and roll axes. Results from flight tests showed with a roll to pitch input coupling failure, the handling qualities went from Level 2 with the baseline controller to Level 1 with the most complex MRAC tested. A failure scenario with the left stabilator frozen also showed improvement with the MRAC. Improvement in performance and handling qualities was generally seen as complexity was incrementally added; however, added complexity usually corresponds to increased verification and validation effort required for certification. The tradeoff between complexity and performance is thus important to a controls system designer when implementing an adaptive controller on an aircraft. This paper investigates this relation through flight testing of several controllers of vary complexity.

High rate science data handling on Space Station Freedom

NASA Technical Reports Server (NTRS)

Handley, Thomas H., Jr.; Masline, Richard C.

1990-01-01

A study by NASA's User Information System Working Group for Space Station Freedom (SSF) has determined that the proposed onboard Data Management System, as initially configured, will be incapable of handling the data-generation rates typical of numerous scientific sensor payloads; many of these generate data at rates in excess of 10 Mbps, and there are at least four cases of rates in excess of 300 Mbps. The SSF Working Group has accordingly suggested an alternative conceptual architecture based on technology expected to achieve space-qualified status by 1995. The architecture encompasses recorders with rapid data-ingest capabilities and massive storage capabilities, optical delay lines allowing the recording of only the phenomena of interest, and data flow-compressing image processors.

Modeling procedures for handling qualities evaluation of flexible aircraft

NASA Technical Reports Server (NTRS)

Govindaraj, K. S.; Eulrich, B. J.; Chalk, C. R.

1981-01-01

This paper presents simplified modeling procedures to evaluate the impact of flexible modes and the unsteady aerodynamic effects on the handling qualities of Supersonic Cruise Aircraft (SCR). The modeling procedures involve obtaining reduced order transfer function models of SCR vehicles, including the important flexible mode responses and unsteady aerodynamic effects, and conversion of the transfer function models to time domain equations for use in simulations. The use of the modeling procedures is illustrated by a simple example.

A flight investigation of the stability, control, and handling qualities of an augmented jet flap STOL airplane

NASA Technical Reports Server (NTRS)

Vomaske, R. F.; Innis, R. C.; Swan, B. E.; Grossmith, S. W.

1978-01-01

The stability, control, and handling qualities of an augmented jet flap STOL airplane are presented. The airplane is an extensively modified de Havilland Buffalo military transport. The modified airplane has two fan-jet engines which provide vectorable thrust and compressed air for the augmentor jet flap and Boundary-Layer Control (BLC). The augmentor and BLC air is cross ducted to minimize asymmetric moments produced when one engine is inoperative. The modifications incorporated in the airplane include a Stability Augmentation System (SAS), a powered elevator, and a powered lateral control system. The test gross weight of the airplane was between 165,000 and 209,000 N (37,000 and 47,000 lb). Stability, control, and handling qualities are presented for the airspeed range of 40 to 180 knots. The lateral-directional handling qualities are considered satisfactory for the normal operating range of 65 to 160 knots airspeed when the SAS is functioning. With the SAS inoperative, poor turn coordination and spiral instability are primary deficiencies contributing to marginal handling qualities in the landing approach. The powered elevator control system enhanced the controllability in pitch, particularly in the landing flare and stall recovery.

Piloted simulator investigation of helicopter control systems effects on handling qualities during instrument flight

NASA Technical Reports Server (NTRS)

Forrest, R. D.; Chen, R. T. N.; Gerdes, R. M.; Alderete, T. S.; Gee, D. R.

1979-01-01

An exploratory piloted simulation was conducted to investigate the effects of the characteristics of helicopter flight control systems on instrument flight handling qualities. This joint FAA/NASA study was motivated by the need to improve instrument flight capability. A near-term objective is to assist in updating the airworthiness criteria for helicopter instrument flight. The experiment consisted of variations of single-rotor helicopter types and levels of stability and control augmentation systems (SCAS). These configurations were evaluated during an omnirange approach task under visual and instrument flight conditions. The levels of SCAS design included a simple rate damping system, collective decoupling plus rate damping, and an attitude command system with collective decoupling. A limited evaluation of stick force versus airspeed stability was accomplished. Some problems were experienced with control system mechanization which had a detrimental effect on longitudinal stability. Pilot ratings, pilot commentary, and performance data related to the task are presented.

Analysis of flexible aircraft longitudinal dynamics and handling qualities. Volume 1: Analysis methods

NASA Technical Reports Server (NTRS)

Waszak, M. R.; Schmidt, D. S.

1985-01-01

As aircraft become larger and lighter due to design requirements for increased payload and improved fuel efficiency, they will also become more flexible. For highly flexible vehicles, the handling qualities may not be accurately predicted by conventional methods. This study applies two analysis methods to a family of flexible aircraft in order to investigate how and when structural (especially dynamic aeroelastic) effects affect the dynamic characteristics of aircraft. The first type of analysis is an open loop model analysis technique. This method considers the effects of modal residue magnitudes on determining vehicle handling qualities. The second method is a pilot in the loop analysis procedure that considers several closed loop system characteristics. Volume 1 consists of the development and application of the two analysis methods described above.

HOPE: An On-Line Piloted Handling Qualities Experiment Data Book

NASA Technical Reports Server (NTRS)

Jackson, E. B.; Proffitt, Melissa S.

2010-01-01

A novel on-line database for capturing most of the information obtained during piloted handling qualities experiments (either flight or simulated) is described. The Hyperlinked Overview of Piloted Evaluations (HOPE) web application is based on an open-source object-oriented Web-based front end (Ruby-on-Rails) that can be used with a variety of back-end relational database engines. The hyperlinked, on-line data book approach allows an easily-traversed way of looking at a variety of collected data, including pilot ratings, pilot information, vehicle and configuration characteristics, test maneuvers, and individual flight test cards and repeat runs. It allows for on-line retrieval of pilot comments, both audio and transcribed, as well as time history data retrieval and video playback. Pilot questionnaires are recorded as are pilot biographies. Simple statistics are calculated for each selected group of pilot ratings, allowing multiple ways to aggregate the data set (by pilot, by task, or by vehicle configuration, for example). Any number of per-run or per-task metrics can be captured in the database. The entire run metrics dataset can be downloaded in comma-separated text for further analysis off-line. It is expected that this tool will be made available upon request

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

NASA Technical Reports Server (NTRS)

Pausder, H. J.; Gerdes, R. M.

1982-01-01

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-Earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment.

Dairy cow handling facilities and the perception of Beef Quality Assurance on Colorado dairies.

PubMed

Adams, A E; Olea-Popelka, F J; Grandin, T; Woerner, D R; Roman-Muniz, I N

2014-02-01

A survey was conducted on Colorado dairies to assess attitudes and practices regarding Dairy Beef Quality Assurance (DBQA). The objectives were to (1) assess the need for a new handling facility that would allow all injections to be administered via DBQA standards; (2) establish if Colorado dairy producers are concerned with DBQA; and (3) assess differences in responses between dairy owners and herdsmen. Of the 95 dairies contacted, 20 (21%) agreed to participate, with a median herd size of 1,178. When asked to rank the following 7 traits--efficiency, animal safety, human safety, ease of animal handling, ease of operation, inject per Beef Quality Assurance (BQA) procedures, and cost--in order of priority when designing a new handling facility, human and animal safety were ranked highest in priority (first or second) by the majority of participants, with ease of animal handling and efficiency ranked next. Interestingly, the administration of injections per BQA standards was ranked sixth or seventh by most participants. Respondents estimated the average annual income from the sale of cull cows to be 4.6% of all dairy income, with 50% receiving at least one carcass discount or condemnation in the past 12 mo. Although almost all of the participating dairy farmers stated that the preferred injection site for medications was the neck region, a significant number admitted to using alternate injection sites. In contrast, no difference was found between responses regarding the preferred and actual location for intravenous injections. Although most participating producers are aware of BQA injection guidelines, they perceive efficiency as more important, which could result in injections being administered in locations not promoted by BQA. Dairy owners and herdsmen disagreed in whether or not workers had been injured in the animal handling area in the last 12 mo. Handling facilities that allow for an efficient and safe way to administer drugs according to BQA guidelines and

Piloted Simulation Assessment of the Impact of Flexible Structures on Handling Qualities of Generic Supersonic Aircraft

NASA Technical Reports Server (NTRS)

Stringer, Mary T.; Cowen, Brandon; Hoffler, Keith D.; Couch, Jesse C.; Ogburn, Marilyn E.; Diebler, Corey G.

2013-01-01

The NASA Langley Research Center Cockpit Motion Facility (CMF) was used to conduct a piloted simulation assessment of the impact of flexible structures on flying qualities. The CMF was used because of its relatively high bandwidth, six degree-of-freedom motion capability. Previous studies assessed and attempted to mitigate the effects of multiple dynamic aeroservoelastic modes (DASE). Those results indicated problems existed, but the specific cause and effect was difficult to ascertain. The goal of this study was to identify specific DASE frequencies, damping ratios, and gains that cause degradation in handling qualities. A generic aircraft simulation was developed and designed to have Cooper-Harper Level 1 handling qualities when flown without DASE models. A test matrix of thirty-six DASE modes was implemented. The modes had frequencies ranging from 1 to 3.5 Hz and were applied to each axis independently. Each mode consisted of a single axis, frequency, damping, and gain, and was evaluated individually by six subject pilots with test pilot backgrounds. Analysis completed to date suggests that a number of the DASE models evaluated degrade the handling qualities of this class of aircraft to an uncontrollable condition.

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

NASA Technical Reports Server (NTRS)

Pausder, H.-J.; Gerdes, R. M.

1982-01-01

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment. Previously announced in STAR as N83-13114

Application of frequency domain handling qualities criteria to the longitudinal landing task

NASA Technical Reports Server (NTRS)

Sarrafian, S. K.; Powers, B. G.

1985-01-01

Under NASA sponsorship, an in-flight simulation of the longitudinal handling qualities of several configurations for the approach and landing tasks was performed on the USAF/AFWAL Total In-Flight Simulator by the Calspan Corporation. The basic configuration was a generic transport airplane with static instability. The control laws included proportional plus integral gain loops to produce pitch-rate and angle-of-attack feedback loops. The evaluation task was a conventional visual approach to a flared touchdown at a designated spot on the runway with a lateral offset. The general conclusions were that the existing criteria are based on pitch-attitude response and that these characteristics do not adequately discriminate between the good and bad configurations of this study. This paper describes the work that has been done to further develop frequency-based criteria in an effort to provide better correlation with the observed data.

The Sternberg Task as a Workload Metric in Flight Handling Qualities Research

NASA Technical Reports Server (NTRS)

Hemingway, J. C.

1984-01-01

The objective of this research was to determine whether the Sternberg item-recognition task, employed as a secondary task measure of spare mental capacity for flight handling qualities (FHQ) simulation research, could help to differentiate between different flight-control conditions. FHQ evaluations were conducted on the Vertical Motion Simulator at Ames Research Center to investigate different primary flight-control configurations, and selected stability and control augmentation levels for helicopers engaged in low-level flight regimes. The Sternberg task was superimposed upon the primary flight-control task in a balanced experimental design. The results of parametric statistical analysis of Sternberg secondary task data failed to support the continued use of this task as a measure of pilot workload. In addition to the secondary task, subjects provided Cooper-Harper pilot ratings (CHPR) and responded to a workload questionnaire. The CHPR data also failed to provide reliable statistical discrimination between FHQ treatment conditions; some insight into the behavior of the secondary task was gained from the workload questionnaire data.

A piloted simulator investigation of augmentation systems to improve helicopter nap-of-the-earth handling qualities

NASA Technical Reports Server (NTRS)

Chen, R. T. N.; Talbot, P. D.; Gerdes, R. M.; Dugan, D. C.

1978-01-01

A piloted simulation study assessed various levels of stability and control augmentation designed to improve the handling qualities of several helicopters in nap-of-the-earth (NOE) flight. Five basic single rotor helicopters - one teetering, two articulated, and two hingeless - which were found to have a variety of major deficiencies in a previous fixed-based simulator study were selected as baseline configurations. The stability and control augmentation systems (SCAS) include simple control augmentation systems (CAS) to decouple pitch and yaw responses due to collective input and to quicken the pitch and roll control responses; SCAS of rate command type designed to optimize the sensitivity and damping and to decouple the pitch-roll due to aircraft angular rate; and attitude command type SCAS. Pilot ratings and commentary are presented as well as performance data related to the task. SCAS control usage and their gain levels associated with specific rotor type are also discussed.

An investigation of the effects of pitch-roll (de)-coupling on helicopter handling qualities

NASA Technical Reports Server (NTRS)

Ockier, C. J.; Pausder, H. J.; Blanken, C. L.

1995-01-01

An investigation of the effects of pitch-roll coupling on helicopter handling qualities was performed by the US Army and DLR, using a NASA ground-based and a DLR inflight simulator. Over 90 different coupling configurations were evaluated using a roll-axis tracking task. The results show that although the current ADS-33C coupling criterion discriminates against those types of coupling typical of conventionally controlled helicopters, it not always suited for the prediction of handling qualities of helicopters with modern control systems. Based on the observation that high frequency inputs during tracking are used to alleviate coupling, a frequency domain pitch-roll coupling criterion that uses the average coupling ratio between the bandwidth and neutral stability frequency is formulated. This criterion provides a more comprehensive coverage with respect to the different types of coupling and shows excellent consistency.

Longitudinal handling qualities during approach and landing of a powered lift STOL aircraft

NASA Technical Reports Server (NTRS)

Franklin, J. A.; Innis, R. C.

1972-01-01

Longitudinal handling qualities evaluations were conducted on the Ames Research Center Flight Simulator for Advanced Aircraft (FSAA) for the approach and landing tasks of a powered lift STOL research aircraft. The test vehicle was a C-8A aircraft modified with a new wing incorporating internal blowing over an augmentor flap. The investigation included: (1) use of various flight path and airspeed control techniques for the basic vehicle; (2) assessment of stability and command augmentation schemes for pitch attitude and airspeed control; (3) determination of the influence of longitudinal and vertical force coupling for the power control; (4) determination of the influence of pitch axis coupling with the thrust vector control; and (5) evaluations of the contribution of stability and command augmentation to recovery from a single engine failure. Results are presented in the form of pilot ratings and commentary substantiated by landing approach time histories.

Summary of the effects of engine throttle response on airplane formation-flying qualities

NASA Technical Reports Server (NTRS)

Walsh, Kevin R.

1993-01-01

A flight evaluation was conducted to determine the effect of engine throttle response characteristics on precision formation-flying qualities. A variable electronic throttle control system was developed and flight-tested on a TF-104G airplane with a J79-11B engine at the NASA Dryden Flight Research Facility. This airplane was chosen because of its known, very favorable thrust response characteristics. Ten research flights were flown to evaluate the effects of throttle gain, time delay, and fuel control rate limiting on engine handling qualities during a demanding precision wing formation task. Handling quality effects of lag filters and lead compensation time delays were also evaluated. The Cooper and Harper Pilot Rating Scale was used to assign levels of handling quality. Data from pilot ratings and comments indicate that throttle control system time delays and rate limits cause significant degradations in handling qualities. Threshold values for satisfactory (level 1) and adequate (level 2) handling qualities of these key variables are presented. These results may provide engine manufacturers with guidelines to assure satisfactory handling qualities in future engine designs.

The effects of aircraft design on STOL ride quality

NASA Technical Reports Server (NTRS)

Jones, C. R.; Jacobson, I. D.

1975-01-01

Effects of aircraft dynamic characteristics on passenger ride quality are investigated to determine ride-quality isocontours similar to aircraft handling-qualities contours. Measurements are made on a moving-base simulator while varying the aircraft short-period and Dutch Roll frequencies and dampings. Both pilot ratings and subjective ride-quality ratings are obtained during flight. Ride and handling qualities were found to be complementary for the Dutch Roll mode, but not for the short-period mode. Regions of optimal ride and handling qualities are defined for the short-period mode, and the effects of turbulence levels studied.

Quality of life and handling experience with the PROSE device: an Indian scenario.

PubMed

Bhattacharya, Pradipta; Mahadevan, Rajeswari

2017-11-01

PROSE (prosthetic replacement of ocular surface ecosystem) device is a custom-designed, corneal vaulting scleral contact lens, which is used in the treatment of irregular corneal conditions to improve vision and comfort. The present study aimed at assessing the success of the PROSE device in an Indian scenario in terms of change in quality of life and to understand the handling issues related to the device use. Thirty-two subjects with various irregular corneal conditions meeting the inclusion criteria were included in the study. Subjects were followed for three months after dispensing the PROSE device. Subjects' demographic details, high and low contrast visual acuity with habitual correction and PROSE device, Visual Function Questionnaire scores (NEI VFQ-25) and Ocular Surface Disease Index (OSDI) scores pre- and post-PROSE treatment were collected and compared. An indigenously developed questionnaire was also administered during the follow-up visit for assessing the handling-related issues faced by the subjects while using the device. Forty eyes of 32 subjects were included in the study, of whom 30 reported for follow-up. The median NEI VFQ-25 score improved from 47.33 points to 77.27 points over a period of three months, which was statistically significant (p < 0.05). There was a statistically significant decrease in median OSDI score from 51.14 points to 13.63 points post-PROSE treatment (p < 0.05). Subjects reported no or very minimal handling-related difficulties associated with the use of the PROSE device. The PROSE treatment can be an effective mode of managing patients with irregular corneal conditions and significantly improved the vision-related quality of life of patients suffering from these conditions. The handling of the device is easy and can be mastered with adequate training. © 2017 Optometry Australia.

Statistical survey of XB-70 airplane responses and control usage with an illustration of the application to handling qualities criteria

NASA Technical Reports Server (NTRS)

Powers, B. G.

1972-01-01

The magnitude and frequency of occurrence of aircraft responses and control inputs during 27 flights of the XB-70 airplane were measured. Exceedance curves are presented for the airplane responses and control usage. A technique is presented which makes use of these exceedance curves to establish or verify handling qualities criteria. This technique can provide a means of incorporating current operational experience in handling qualities requirements for future aircraft.

The Airline Quality Rating 2004

NASA Technical Reports Server (NTRS)

Fink, Mary M. (Editor); Bowen, Brent D.; Headley, Dean E.

2004-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline quality on combined multiple performance criteria. This current report, the Airline Quality Rating 2004, reflects monthly Airline Quality Rating scores for 2003. AQR scores for the calendar year 2003 are based on 15 elements in four major areas that focus on airline performance aspects important to air travel consumers. The Airline Quality Rating 2004 is a summary of month-by-month quality ratings for U.S. airlines that have at least 1 % of domestic passenger volume during 2003. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of on-time arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, airlines comparative performance for the calendar year of 2003 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for domestic airline operations for the 12-month period of 2003, and industry results. Also, comparative Airline Quality Rating data for 2002 are included, where available, to provide historical perspective regarding performance quality in the industry.

The Airline Quality Rating 2003

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

2003-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline quality on combined multiple performance criteria. This current report, the Airline Quality Rating 2003, reflects monthly Airline Quality Rating scores for 2002. AQR scores for the calendar year 2002 are based on 15 elements that focus on airline performance areas important to air travel consumers. The Airline Quality Rating 2003 is a summary of month-by-month quality ratings for the 10 largest U.S. airlines operating during 2002. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of ontime arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, airlines comparative performance for the calendar year of 2002 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for domestic airline operations for the 12-month period of 2002, and industry average results. Also, comparative Airline Quality Rating data for 2001 are included for each airline to provide historical perspective regarding performance quality in the industry.

The Airline Quality Rating 2002

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

2002-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline quality on combined multiple performance criteria. This current report, Airline Quality Rating 2002, reflects monthly Airline Quality Rating scores for 2001. AQR scores for the calendar year 2001 are based on 15 elements that focus on airline performance areas important to air travel consumers. The Airline Quality Rating 2002 is a summary of month-by-month quality ratings for the 11 largest U.S. airlines operating during 2001. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of on-time arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, airlines comparative performance for the calendar year of 2001 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for domestic airline operations for the 12-month period of 2001, and industry average results. Also, comparative Airline Quality Rating data for 2000 are included for each airline to provide historical perspective regarding performance quality in the industry.

The Airline Quality Rating 2001

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

2001-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline quality on combined multiple performance criteria. This current report, Airline Quality Rating 2001, reflects monthly Airline Quality Rating scores for 2000. AQR scores for the calendar year 2000 are based on 15 elements that focus on airline performance areas important to air travel consumers. The Airline Quality Rating 2001 is a summary of month-by-month quality ratings for the ten major U.S. airlines operating during 2000. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of on-time arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, major airlines comparative performance for the calendar year of 2000 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for major airlines domestic operations for the 12 month period of 2000, and industry average results. Also, comparative Airline Quality Rating data for 1999 are included for each airline to provide historical perspective regarding performance quality in the industry.

Modal control theory and application to aircraft lateral handling qualities design

NASA Technical Reports Server (NTRS)

Srinathkumar, S.

1978-01-01

A multivariable synthesis procedure based on eigenvalue/eigenvector assignment is reviewed and is employed to develop a systematic design procedure to meet the lateral handling qualities design objectives of a fighter aircraft over a wide range of flight conditions. The closed loop modal characterization developed provides significant insight into the design process and plays a pivotal role in the synthesis of robust feedback systems. The simplicity of the synthesis algorithm yields an efficient computer aided interactive design tool for flight control system synthesis.

The Airline Quality Rating 1999

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

1999-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline performance on combined multiple criteria. This current report, Airline Quality Rating 1999, reflects an updated approach to calculating monthly Airline Quality Rating scores for 1998. AQR scores for the calendar year 1998 are based on 15 elements that focus on airline performance areas important to air travel consumers. The Airline Quality Rating is a summary of month-by-month quality ratings for the ten major U.S. airlines operating during 1998. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of on-time arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, major airlines comparative performance for the calendar year 1998 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for major airlines domestic operations for the 12 month period of 1998, and industry average results. Also, comparative Airline Quality Rating data for 1997, using the updated criteria, are included to provide a reference point regarding quality in the industry.

The Airline Quality Rating 2004

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

2004-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline quality on combined multiple performance criteria. This current report, the Airline Quality Rating 2004, reflects monthly Airline Quality Rating scores for 2003. AQR scores far the calendar year 2003 are based on 15 elemnts in four major areas that focus on airline performance aspects important to air travel consumers. The Airline Quality Rating 2004 is a summary of month-by-month quality ratings for U.S. airlines that have at least 1% of domestic passenger volume during 2003. Using the Airline Quality Rating system of weighted averages and monthly performance data in the areas of on-time arrivals, involuntary denied boardings, mishandled baggage, and a combination of 12 customer complaint categories, airlines comparative performance for the calendar year of 2003 is reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for domestic airline operations for the 12-month period of 2003, and industry results. Also, comparative Airline Quality Rating data for 2002 are included, where available, to provide historical perspective

Presentation of flight control design and handling quality commonality by separate surface stability augmentation for the family of commuter airplanes

NASA Technical Reports Server (NTRS)

Hensley, Douglas; Creighton, Thomas; Haddad, Raphael; Hendrich, Louis; Morgan, Louise; Russell, Mark; Swift, Gerald

1987-01-01

The methodology and results for a flight control design and implementation for common handling qualities by Separate Surface Stability Augmentation (SSSA) for the family of commuter airplanes are contained. The open and closed loop dynamics and the design results of augmenting for common handling qualities are presented. The physical and technology requirements are presented for implementing the SSSA system. The conclusion of this report and recommendations for changes or improvement are discussed.

Missouri Quality Rating System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Missouri's Quality Rating System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

A design procedure and handling quality criteria for lateral directional flight control systems

NASA Technical Reports Server (NTRS)

Stein, G.; Henke, A. H.

1972-01-01

A practical design procedure for aircraft augmentation systems is described based on quadratic optimal control technology and handling-quality-oriented cost functionals. The procedure is applied to the design of a lateral-directional control system for the F4C aircraft. The design criteria, design procedure, and final control system are validated with a program of formal pilot evaluation experiments.

Some lessons learned in three years with ADS-33C. [rotorcraft handling qualities specification

NASA Technical Reports Server (NTRS)

Key, David L.; Blanken, Chris L.; Hoh, Roger H.

1993-01-01

Three years of using the U.S. Army's rotorcraft handling qualities specification, Aeronautical Design Standard - 33, has shown it to be surprisingly robust. It appears to provide an excellent basis for design and for assessment, however, as the subtleties become more well understood, several areas needing refinement became apparent. Three responses to these needs have been documented in this paper: (1) The yaw-axis attitude quickness for hover target acquisition and tracking can be relaxed slightly. (2) Understanding and application of criteria for degraded visual environments needed elaboration. This and some guidelines for testing to obtain visual cue ratings have been documented. (3) The flight test maneuvers were an innovation that turned out to be very valuable. Their extensive use has made it necessary to tighten definitions and testing guidance. This was accomplished for a good visual environment and is underway for degraded visual environments.

Orion Capsule Handling Qualities for Atmospheric Entry

NASA Technical Reports Server (NTRS)

Tigges, Michael A.; Bihari, Brian D.; Stephens, John-Paul; Vos, Gordon A.; Bilimoria, Karl D.; Mueller, Eric R.; Law, Howard G.; Johnson, Wyatt; Bailey, Randall E.; Jackson, Bruce

2011-01-01

Two piloted simulations were conducted at NASA's Johnson Space Center using the Cooper-Harper scale to study the handling qualities of the Orion Command Module capsule during atmospheric entry flight. The simulations were conducted using high fidelity 6-DOF simulators for Lunar Return Skip Entry and International Space Station Return Direct Entry flight using bank angle steering commands generated by either the Primary (PredGuid) or Backup (PLM) guidance algorithms. For both evaluations, manual control of bank angle began after descending through Entry Interface into the atmosphere until drogue chutes deployment. Pilots were able to use defined bank management and reversal criteria to accurately track the bank angle commands, and stay within flight performance metrics of landing accuracy, g-loads, and propellant consumption, suggesting that the pilotability of Orion under manual control is both achievable and provides adequate trajectory performance with acceptable levels of pilot effort. Another significant result of these analyses is the applicability of flying a complex entry task under high speed entry flight conditions relevant to the next generation Multi Purpose Crew Vehicle return from Mars and Near Earth Objects.

Microbiological quality and safe handling of enteral diets in a hospital in Minas Gerais, Brazil.

PubMed

Pinto, Raquel Oliveira Medrado; Correia, Eliznara Fernades; Pereira, Keyla Carvalho; Costa Sobrinho, Paulo de Souza; da Silva, Daniele Ferreira

2015-06-01

Contamination of enteral diets represents a high risk of compromising the patient's medical condition. To assess the microbiological quality and aseptic conditions in the preparation and administration of handmade and industrialized enteral diets offered in a hospital in the Valley of Jequitinhonha, MG, Brazil, we performed a microbiological analysis of 50 samples of diets and 27 samples of surfaces, utensils, and water used in the preparation of the diets. In addition, we assessed the good handling practices of enteral diets according to the requirements specified by the Brazilian legislation. Both kinds of enteral diets showed contamination by coliforms and Pseudomonas spp. No sample was positive for Staphylococcus aureus and Salmonella spp. On the other hand, Listeria spp. was detected in only one sample of handmade diets. Contamination was significantly higher in the handmade preparations (p < 0.05). Nonconformities were detected with respect to good handling practices, which may compromise the diet safety. The results indicate that the sanitary quality of the enteral diets is unsatisfactory, especially handmade diets. Contamination by Pseudomonas spp. is significant because it is often involved in infection episodes. With regard to aseptic practices, it was observed the need of implementing new procedures for handling enteral diets.

Microbiological quality and safe handling of enteral diets in a hospital in Minas Gerais, Brazil

PubMed Central

Pinto, Raquel Oliveira Medrado; Correia, Eliznara Fernades; Pereira, Keyla Carvalho; Costa, Paulo de Souza; da Silva, Daniele Ferreira

2015-01-01

Contamination of enteral diets represents a high risk of compromising the patient's medical condition. To assess the microbiological quality and aseptic conditions in the preparation and administration of handmade and industrialized enteral diets offered in a hospital in the Valley of Jequitinhonha, MG, Brazil, we performed a microbiological analysis of 50 samples of diets and 27 samples of surfaces, utensils, and water used in the preparation of the diets. In addition, we assessed the good handling practices of enteral diets according to the requirements specified by the Brazilian legislation. Both kinds of enteral diets showed contamination by coliforms and Pseudomonas spp. No sample was positive for Staphylococcus aureus and Salmonella spp. On the other hand, Listeria spp. was detected in only one sample of handmade diets. Contamination was significantly higher in the handmade preparations (p < 0.05). Nonconformities were detected with respect to good handling practices, which may compromise the diet safety. The results indicate that the sanitary quality of the enteral diets is unsatisfactory, especially handmade diets. Contamination by Pseudomonas spp. is significant because it is often involved in infection episodes. With regard to aseptic practices, it was observed the need of implementing new procedures for handling enteral diets. PMID:26273278

Effect of winglets on performance and handling qualities of general aviation aircraft

NASA Technical Reports Server (NTRS)

Van Dam, C. P.; Holmes, B. J.; Pitts, C.

1980-01-01

Recent flight and wind tunnel evaluations of winglets mounted on general aviation airplanes have shown improvements in cruise fuel efficiency, and climbing and turning performance. Some of these analyses have also uncovered various effects of winglets on airplane handling qualities. Retrofitting an airplane with winglets can result in reduced cross wind take-off and landing capabilities. Also, winglets can have a detrimental effect on the lateral directional response characteristics of aircraft which have a moderate to high level of adverse yaw due to aileron. Introduction of an aileron-rudder-interconnect, and reduction of the effective dihedral by canting-in of the winglets, or addition of a lower winglet can eliminate these flying quality problems.

An investigation of the effects of pitch-roll (de)coupling on helicopter handling qualities

NASA Technical Reports Server (NTRS)

Blanken, C. L.; Pausder, H. J.; Ockier, C. J.

1995-01-01

An extensive investigation of the effects of pitch-roll coupling on helicopter handling qualities was performed by the U.S. Army and Deutsche Forschungsanstalt fur Luft- und Raumfahrt (DLR), using a NASA ground-based and a DLR in-flight simulator. Over 90 different coupling configurations were evaluated using a high gain roll-axis tracking task. The results show that although the current ADS-33C coupling criterion discriminates against those types of coupling typical of conventionally controlled helicopters, it is not always suited for the prediction of handling qualities of helicopters with modern control systems. Based on the observation that high frequency inputs during tracking are used to alleviate coupling, a frequency domain pitch-roll coupling criterion that uses the average coupling ratio between the bandwidth and neutral stability frequency is formulated. This criterion provides a more comprehensive coverage with respect to the different types of coupling, shows excellent consistency, and has the additional benefit that compliance testing data are obtained from the bandwidth/phase delay tests, so that no additional flight testing is needed.

New Hampshire Quality Rating System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of New Hampshire's Quality Rating System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4)…

Summary of the effects of engine throttle response on airplane formation-flying qualities

NASA Technical Reports Server (NTRS)

Walsh, Kevin R.

1992-01-01

A flight evaluation as conducted to determine the effect of engine throttle response characteristics on precision formation-flying qualities. A variable electronic throttle control system was developed and flight-tested on a TF-104G airplane with a J79-11B engine at the NASA Dryden Flight Research Facility. Ten research flights were flown to evaluate the effects of throttle gain, time delay, and fuel control rate limiting on engine handling qualities during a demanding precision wing formation task. Handling quality effects of lag filters and lead compensation time delays were also evaluated. Data from pilot ratings and comments indicate that throttle control system time delays and rate limits cause significant degradations in handling qualities. Threshold values for satisfactory (level 1) and adequate (level 2) handling qualities of these key variables are presented.

Archive data base and handling system for the Orbiter flying qualities experiment program

NASA Technical Reports Server (NTRS)

Myers, T. T.; Dimarco, R.; Magdaleno, R. E.; Aponso, B. L.

1986-01-01

The OFQ archives data base and handling system assembled as part of the Orbiter Flying Qualities (OFQ) research of the Orbiter Experiments Program (EOX) are described. The purpose of the OFQ archives is to preserve and document shuttle flight data relevant to vehicle dynamics, flight control, and flying qualities in a form that permits maximum use for qualified users. In their complete form, the OFQ archives contain descriptive text (general information about the flight, signal descriptions and units) as well as numerical time history data. Since the shuttle program is so complex, the official data base contains thousands of signals and very complex entries are required to obtain data. The OFQ archives are intended to provide flight phase oriented data subsets with relevant signals which are easily identified for flying qualities research.

Flight Dynamics Aspects of a Large Civil Tiltrotor Simulation Using Translational Rate Command

NASA Technical Reports Server (NTRS)

Lawrence, Ben; Malpica, Carlos A.; Theodore, Colin R.; Decker, William A.; Lindsey, James E.

2011-01-01

An in-depth analysis of a Large Civil Tiltrotor simulation with a Translational Rate Command control law that uses automatic nacelle deflections for longitudinal velocity control and lateral cyclic for lateral velocity control is presented. Results from piloted real-time simulation experiments and offline time and frequency domain analyses are used to investigate the fundamental flight dynamic and control mechanisms of the control law. The baseline Translational Rate Command conferred handling qualities improvements over an attitude command attitude hold control law but in some scenarios there was a tendency to enter PIO. Nacelle actuator rate limiting strongly influenced the PIO tendency and reducing the rate limits degraded the handling qualities further. Counterintuitively, increasing rate limits also led to a worsening of the handling qualities ratings. This led to the identification of a nacelle rate to rotor longitudinal flapping coupling effect that induced undesired pitching motions proportional to the allowable amount of nacelle rate. A modification that applied a counteracting amount of longitudinal cyclic proportional to the nacelle rate significantly improved the handling qualities. The lateral axis of the Translational Rate Command conferred Level 1 handling qualities in a Lateral Reposition maneuver. Analysis of the influence of the modeling fidelity on the lateral flapping angles is presented. It is showed that the linear modeling approximation is likely to have under-predicted the side-force and therefore under-predicted the lateral flapping at velocities above 15 ft/s. However, at lower velocities, and therefore more weakly influenced by the side force modeling, the accelerations that the control law commands also significantly influenced the peak levels of lateral flapping achieved.

Dynamic stability and handling qualities tests on a highly augmented, statically unstable airplane

NASA Technical Reports Server (NTRS)

Gera, Joseph; Bosworth, John T.

1987-01-01

This paper describes some novel flight tests and analysis techniques in the flight dynamics and handling qualities area. These techniques were utilized during the initial flight envelope clearance of the X-29A aircraft and were largely responsible for the completion of the flight controls clearance program without any incidents or significant delays. The resulting open-loop and closed-loop frequency responses and the time history comparison using flight and linear simulation data are discussed.

Analysis of the longitudinal handling qualities and pilot-induced-oscillation tendencies of the High-Angle-of-Attack Research Vehicle (HARV)

NASA Technical Reports Server (NTRS)

Hess, Ronald A.

1994-01-01

The NASA High-Angle-of Attack Research Vehicle (HARV), a modified F-18 aircraft, experienced handling qualities problems in recent flight tests at NASA Dryden Research Center. Foremost in these problems was the tendency of the pilot-aircraft system to exhibit a potentially dangerous phenomenon known as a pilot-induced oscillation (PIO). When they occur, PIO's can severely restrict performance, sharply dimish mission capabilities, and can even result in aircraft loss. A pilot/vehicle analysis was undertaken with the goal of reducing these PIO tendencies and improving the overall vehicle handling qualities with as few changes as possible to the existing feedback/feedforward flight control laws. Utilizing a pair of analytical pilot models developed by the author, a pilot/vehicle analysis of the existing longitudinal flight control system was undertaken. The analysis included prediction of overall handling qualities levels and PIO susceptability. The analysis indicated that improvement in the flight control system was warranted and led to the formulation of a simple control stick command shaping filter. Analysis of the pilot/vehicle system with the shaping filter indicated significant improvements in handling qualities and PIO tendencies could be achieved. A non-real time simulation of the modified control system was undertaken with a realistic, nonlinear model of the current HARV. Special emphasis was placed upon those details of the command filter implementation which could effect safety of flight. The modified system is currently awaiting evaluation in the real-time, pilot-in-the-loop, Dual-Maneuvering-Simulator (DMS) facility at Langley.

Monitoring oral temperature, heart rate, and respiration rate of West Indian manatees (Trichechus manatus) during capture and handling in the field

USGS Publications Warehouse

Wong, Arthur W.; Bonde, Robert K.; Siegal-Willott, Jessica; Stamper, M. Andrew; Colee, James; Powell, James A.; Reid, James P.; Deutsch, Charles J.; Harr, Kendal E.

2012-01-01

West Indian manatees (Trichechus manatus) are captured, handled, and transported to facilitate conservation, research, and rehabilitation efforts. Monitoring manatee oral temperature (OT), heart rate (HR), and respiration rate (RR) during out-of-water handling can assist efforts to maintain animal well-being and improve medical response to evidence of declining health. To determine effects of capture on manatee vital signs, we monitored OT, HR, and RR continuously for a 50-min period in 38 healthy, awake, juvenile and adult Florida manatees (T. m. latirostris) and 48 similar Antillean manatees (T. m. manatus). We examined creatine kinase (CK), potassium (K+), serum amyloid A (SAA), and lactate values for each animal to assess possible systemic inflammation and muscular trauma. OT range was 29.5 to 36.2° C, HR range was 32 to 88 beats/min, and RR range was 0 to 17 breaths/5 min. Antillean manatees had higher initial OT, HR, and RR than Florida manatees (p < 0.001). As monitoring time progressed, mean differences between the subspecies were no longer significant. High RR over monitoring time was associated with high lactate concentration. Antillean manatees had higher overall lactate values ([mean ± SD] 20.6 ± 7.8 mmol/L) than Florida manatees (13.7 ± 6.7 mmol/L; p < 0.001). We recommend monitoring manatee OT, HR, and RR during capture and handling in the field or in a captive care setting.

Analysis of Handling Qualities Design Criteria for Active Inceptor Force-Feel Characteristics

NASA Technical Reports Server (NTRS)

Malpica, Carlos A.; Lusardi, Jeff A.

2013-01-01

The force-feel system characteristics of the cyclic inceptors of most helicopters are set based on the characteristics of the mechanical components in the control system (mass, springs, friction dampers, etc.). For these helicopters, the force-feel characteristics typically remain constant over the entire flight envelope, with perhaps a trim release to minimize control forces while maneuvering. With the advent of fly-by-wire control systems and active inceptors in helicopters, the force-feel characteristics are now determined by the closed-loop response of the active inceptor itself as defined by the inertia, force/displacement gradient, damping, breakout force and detent shape configuration parameters in the inceptor control laws. These systems give the flexibility to dynamically prescribe different feel characteristics for different control modes or flight conditions, and the ability to provide tactile cueing to the pilot through the actively controlled side-stick or center-stick cyclic inceptor. For rotorcraft, a few studies have been conducted to assess the effects of cyclic force-feel characteristics on handling qualities in flight. An early study provided valuable insight into the static force-deflection characteristics (force gradient) and the number of axes controlled by the side-stick controller for the U.S. Army's Advanced Digital/Optical Control System (ADOCS) demonstrator aircraft [1]. The first of a series of studies providing insight on the inceptor dynamic force-feel characteristics was conducted on the NASA/Army CH-47B variable-stability helicopter [2]. This work led to a proposed requirement that set boundaries based on the cyclic natural frequency and inertia, with the stipulation of a lower damping ratio limit of 0.3 [3]. A second study was conducted by the Canadian Institute for Aerospace Research using their variable-stability Bell 205A helicopter [4]. This research suggested boundaries for stick dynamics based on natural frequency and damping

Iowa Child Care Quality Rating System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Iowa's Child Care Quality Rating System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile is divided into the following categories: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family Child Care Programs;…

Estimation of Handling Qualities Parameters of the Tu-144 Supersonic Transport Aircraft from Flight Test Data

NASA Technical Reports Server (NTRS)

Curry, Timothy J.; Batterson, James G. (Technical Monitor)

2000-01-01

Low order equivalent system (LOES) models for the Tu-144 supersonic transport aircraft were identified from flight test data. The mathematical models were given in terms of transfer functions with a time delay by the military standard MIL-STD-1797A, "Flying Qualities of Piloted Aircraft," and the handling qualities were predicted from the estimated transfer function coefficients. The coefficients and the time delay in the transfer functions were estimated using a nonlinear equation error formulation in the frequency domain. Flight test data from pitch, roll, and yaw frequency sweeps at various flight conditions were used for parameter estimation. Flight test results are presented in terms of the estimated parameter values, their standard errors, and output fits in the time domain. Data from doublet maneuvers at the same flight conditions were used to assess the predictive capabilities of the identified models. The identified transfer function models fit the measured data well and demonstrated good prediction capabilities. The Tu-144 was predicted to be between level 2 and 3 for all longitudinal maneuvers and level I for all lateral maneuvers. High estimates of the equivalent time delay in the transfer function model caused the poor longitudinal rating.

Effects of cockpit lateral stick characteristics on handling qualities and pilot dynamics

NASA Technical Reports Server (NTRS)

Mitchell, David G.; Aponso, Bimal L.; Klyde, David H.

1992-01-01

This report presents the results of analysis of cockpit lateral control feel-system studies. Variations in feel-system natural frequency, damping, and command sensing reference (force and position) were investigated, in combination with variations in the aircraft response characteristics. The primary data for the report were obtained from a flight investigation conducted with a variable-stability airplane, with additional information taken from other flight experiments and ground-based simulations for both airplanes and helicopters . The study consisted of analysis of handling qualities ratings and extraction of open-loop, pilot-vehicle describing functions from sum-of-sines tracking data, including, for a limited subset of these data, the development of pilot models. The study confirms the findings of other investigators that the effects on pilot opinion of cockpit feel-system dynamics are not equivalent to a comparable level of added time delay, and until a more comprehensive set of criteria are developed, it is recommended that feel-system dynamics be considered a delay-inducing element in the aircraft response. The best correlation with time-delay requirements was found when the feel-system dynamics were included in the delay measurements, regardless of the command reference. This is a radical departure from past approaches.

Louisiana Quality Start Child Care Rating System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Louisiana's Quality Start Child Care Rating System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs;…

NHEXAS PHASE I REGION 5 STUDY--STANDARD OPERATING PROCEDURE--HANDLING QUALITY CONTROL SAMPLES IN THE FIELD (RTI/ACS-AP-209-090)

EPA Science Inventory

This protocol describes how quality control samples should be handled in the field, and was designed as a quick reference source for the field staff. The protocol describes quality control samples for air-VOCs, air-particles, water samples, house dust, soil, urine, blood, hair, a...

Handling Qualities Flight Testing of the Stratospheric Observatory for Infrared Astronomy (SOFIA)

NASA Technical Reports Server (NTRS)

Glaser, Scott T.; Strovers, Brian K.

2011-01-01

Airborne infrared astronomy has a long successful history, albeit relatively unknown outside of the astronomy community. A major problem with ground based infrared astronomy is the absorption and scatter of infrared energy by water in the atmosphere. Observing the universe from above 40,000 ft puts the observation platform above 99% of the water vapor in the atmosphere, thereby addressing this problem at a fraction of the cost of space based systems. The Stratospheric Observatory For Infrared Astronomy (SOFIA) aircraft is the most ambitious foray into the field of airborne infrared astronomy in history. Using a 747SP (The Boeing Company, Chicago, Illinois) aircraft modified with a 2.5m telescope located in the aft section of the fuselage, the SOFIA endeavors to provide views of the universe never before possible and at a fraction of the cost of space based systems. The modification to the airplane includes moveable doors and aperture that expose the telescope assembly. The telescope assembly is aimed and stabilized using a multitude of on board systems. This modification has the potential to cause aerodynamic anomalies that could induce undesired forces either at the cavity itself or indirectly due to interference with the empennage, both of which could cause handling qualities issues. As a result, an extensive analysis and flight test program was conducted from December 2009 through March 2011. Several methods, including a Lower Order Equivalent Systems analysis and pilot assessment, were used to ascertain the effects of the modification. The SOFIA modification was found to cause no adverse handling qualities effects and the aircraft was cleared for operational use. This paper discusses the history and modification to the aircraft, development of test procedures and analysis, results of testing and analysis, lessons learned for future projects and justification for operational certification.

Uncertainties of stormwater characteristics and removal rates of stormwater treatment facilities: implications for stormwater handling.

PubMed

Langeveld, J G; Liefting, H J; Boogaard, F C

2012-12-15

Stormwater runoff is a major contributor to the pollution of receiving waters. This study focuses at characterising stormwater in order to be able to determine the impact of stormwater on receiving waters and to be able to select the most appropriate stormwater handling strategy. The stormwater characterisation is based on determining site mean concentrations (SMCs) and their uncertainties as well as the treatability of stormwater by monitoring specific pollutants concentration levels (TSS, COD, BOD, TKN, TP, Pb, Cu, Zn, E.coli) at three full scale stormwater treatment facilities in Arnhem, the Netherlands. This has resulted in 106 storm events being monitored at the lamella settler, 59 at the high rate sand filter and 132 at the soil filter during the 2 year monitoring period. The stormwater characteristics in Arnhem in terms of SMCs for main pollutants TSS and COD and settling velocities differ from international data. This implies that decisions for stormwater handling made on international literature data will very likely be wrong due to assuming too high concentrations of pollutants and misjudgement of the treatability of stormwater. The removal rates monitored at the full scale treatment facilities are within the expected range, with the soil filter and the sand filter having higher removal rates than the lamella settler. The full scale pilots revealed the importance of incorporating gross solids removal in the design of stormwater treatment facilities, as the gross solids determine operation and maintenance requirements. Copyright © 2012 Elsevier Ltd. All rights reserved.

The Airline Quality Rating 2001 (PDF file)

DOT National Transportation Integrated Search

2001-04-01

The Airline Quality Rating (AQR) was developed and first announced in early : 1991 as an objective method of comparing airline quality on combined multiple : performance criteria. This current report, Airline Quality Rating 2001, reflects monthly Air...

A modal analysis of flexible aircraft dynamics with handling qualities implications

NASA Technical Reports Server (NTRS)

Schmidt, D. K.

1983-01-01

A multivariable modal analysis technique is presented for evaluating flexible aircraft dynamics, focusing on meaningful vehicle responses to pilot inputs and atmospheric turbulence. Although modal analysis is the tool, vehicle time response is emphasized, and the analysis is performed on the linear, time-domain vehicle model. In evaluating previously obtained experimental pitch tracking data for a family of vehicle dynamic models, it is shown that flexible aeroelastic effects can significantly affect pitch attitude handling qualities. Consideration of the eigenvalues alone, of both rigid-body and aeroelastic modes, does not explain the simulation results. Modal analysis revealed, however, that although the lowest aeroelastic mode frequency was still three times greater than the short-period frequency, the rigid-body attitude response was dominated by this aeroelastic mode. This dominance was defined in terms of the relative magnitudes of the modal residues in selected vehicle responses.

Quality Rating and Improvement Systems: A Strategic Movement for Defining Quality

ERIC Educational Resources Information Center

Neugebauer, Roger

2009-01-01

One of the most important trends in the early childhood field is the emergence of quality rating systems (QRS), or quality rating and improvement systems (QRIS), which are designed to assess, improve, and communicate the level of quality of early and school-age care programs. QRS came onto the scene in 1998 when Oklahoma enacted its "Reaching…

A design procedure for the handling qualities optimization of the X-29A aircraft

NASA Technical Reports Server (NTRS)

Bosworth, John T.; Cox, Timothy H.

1989-01-01

The techniques used to improve the pitch-axis handling qualities of the X-29A wing-canard-planform fighter aircraft are reviewed. The aircraft and its FCS are briefly described, and the design method, which works within the existing FCS architecture, is characterized in detail. Consideration is given to the selection of design goals and design variables, the definition and calculation of the cost function, the validation of the mathematical model on the basis of flight-test data, and the validation of the improved design by means of nonlinear simulations. Flight tests of the improved design are shown to verify the simulation results.

Evaluation of 100 brain examinations using a 3 Tesla MR-compatible incubator-safety, handling, and image quality.

PubMed

Sirin, Selma; Goericke, Sophia L; Huening, Britta M; Stein, Anja; Kinner, Sonja; Felderhoff-Mueser, Ursula; Schweiger, Bernd

2013-10-01

Several studies have revealed the importance of brain imaging in term and preterm infants. The aim of this retrospective study was to review safety, handling, and image quality of MR brain imaging using a new 3 Tesla MR-compatible incubator. Between 02/2011 and 05/2012 100 brain MRIs (84 infants, mean gestational age 32.2 ± 4.7 weeks, mean postmenstrual age at imaging 40.6 ± 3.4 weeks) were performed using a 3 Tesla MR-compatible incubator with dedicated, compatible head coil. Seventeen examinations (13 infants, mean gestational age 35.1 ± 5.4 weeks, mean postmenstrual age at imaging 47.8 ± 7.4 weeks) with a standard head coil served as a control. Image analysis was performed by a neuroradiologist and a pediatric radiologist in consensus. All but two patients with known apnea were transferred to the MR unit and scanned without problems. Handling was easier and faster with the incubator; relevant motion artifacts (5.9 vs. 10.8%) and the need for repetitive sedation (43.0 vs. 86.7%) were reduced. Considering only images not impaired by motion artifacts, image quality (4.8 ± 0.4 vs. 4.3 ± 0.8, p = 0.047) and spatial resolution (4.7 ± 0.4 vs. 4.2 ± 0.6, p = 0.011) of T2-weighted images were scored significantly higher in patients imaged with the incubator. SNR increased significantly (171.6 ± 54.5 vs. 80.5 ± 19.8, p < 0.001) with the use of the incubator. Infants can benefit from the use of a 3 Tesla MR-compatible incubator because of its safety, easier, and faster handling (compared to standard imaging) and possibility to obtain high-quality MR images even in unstable patients.

An experimental evaluation of the Sternberg task as a workload metric for helicopter Flight Handling Qualities (FHQ) research

NASA Technical Reports Server (NTRS)

Hemingway, J. C.

1984-01-01

The objective was to determine whether the Sternberg item-recognition task, employed as a secondary task measure of spare mental capacity for flight handling qualities (FHQ) simulation research, could help to differentiate between different flight-control conditions. FHQ evaluations were conducted on the Vertical Motion Simulator at Ames Research Center to investigate different primary flight-control configurations, and selected stability and control augmentation levels for helicopters engaged in low-level flight regimes. The Sternberg task was superimposed upon the primary flight-control task in a balanced experimental design. The results of parametric statistical analysis of Sternberg secondary task data failed to support the continued use of this task as a measure of pilot workload. In addition to the secondary task, subjects provided Cooper-Harper pilot ratings (CHPR) and responded to workload questionnaire. The CHPR data also failed to provide reliable statistical discrimination between FHQ treatment conditions; some insight into the behavior of the secondary task was gained from the workload questionnaire data.

45 CFR 155.1400 - Quality rating system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... the quality rating information assigned to each QHP on its Web site, in accordance with § 155.205(b)(1... 45 Public Welfare 1 2014-10-01 2014-10-01 false Quality rating system. 155.1400 Section 155.1400... EXCHANGE ESTABLISHMENT STANDARDS AND OTHER RELATED STANDARDS UNDER THE AFFORDABLE CARE ACT Quality...

Complying with US and European complaint handling requirements.

PubMed

Donawa, M E

1997-09-01

The importance of customer complaints for providing valuable information on the use of medical devices is clearly reflected in United States (US) and European quality system requirements for handling complaints. However, there are significant differences in US and European complaint handling requirements. This article will discuss those differences and methods for ensuring compliance.

COST VS. QUALITY IN DEMOGRAPHIC MODELLING: WHEN IS A VITAL RATE GOOD ENOUGH?

EPA Science Inventory

This presentation will focus on the assessment of quality for demographic parameters to be used in population-level risk assessment. Current population models can handle genetic, demographic, and environmental stochasticity, density dependence, and multiple stressors. However, cu...

Ground data handling for LANDSAT-D

NASA Technical Reports Server (NTRS)

Lynch, T. J.

1976-01-01

The present plans for the LANDSAT D ground data handling are described in relationship to the mission objectives and the planned spacecraft system. The end to end data system is presented with particular emphasis on the data handling plans for the new instrument, the Thematic Mapper. This instrument generates ten times the amount of data per scene as the present Multispectral Scanner, and this resulting data rate and volume are discussed as well as possible new data techniques to handle them such as image compression.

Dynamic stability and handling qualities tests on a highly augmented, statically unstable airplane

NASA Technical Reports Server (NTRS)

Gera, Joseph; Bosworth, John T.

1987-01-01

Initial envelope clearance and subsequent flight testing of a new, fully augmented airplane with an extremely high degree of static instability can place unusual demands on the flight test approach. Previous flight test experience with these kinds of airplanes is very limited or nonexistent. The safe and efficient flight testing may be further complicated by a multiplicity of control effectors that may be present on this class of airplanes. This paper describes some novel flight test and analysis techniques in the flight dynamics and handling qualities area. These techniques were utilized during the initial flight envelope clearance of the X-29A aircraft and were largely responsible for the completion of the flight controls clearance program without any incidents or significant delays.

The UNO Aviation Monograph Series: The Airline Quality Rating 1998

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

1998-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline performance on combined multiple factors important to consumers. Development history and calculation details for the AQR rating system are detailed in The Airline Quality Rating 1991 issued in April, 1991, by the National Institute for Aviation Research at Wichita State University. This current report, Airline Quality Rating 1998, contains monthly Airline Quality Rating scores for 1997. Additional copies are available by contacting Wichita State University or University of Nebraska at Omaha. The Airline Quality Rating 1998 is a summary of month-by-month quality ratings for the ten major U.S. airlines operating during 1997. Using the Airline Quality Rating system and monthly performance data for each airline for the calendar year of 1997, individual and comparative ratings are reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for major airlines domestic operations for the 12 month period of 1997, and industry average results. Also, comparative Airline Quality Rating data for 1991 through 1996 are included to provide a longer term view of quality in the industry.

Dose rate prediction methodology for remote handled transuranic waste workers at the waste isolation pilot plant.

PubMed

Hayes, Robert

2002-10-01

An approach is described for estimating future dose rates to Waste Isolation Pilot Plant workers processing remote handled transuranic waste. The waste streams will come from the entire U.S. Department of Energy complex and can take on virtually any form found from the processing sequences for defense-related production, radiochemistry, activation and related work. For this reason, the average waste matrix from all generator sites is used to estimate the average radiation fields over the facility lifetime. Innovative new techniques were applied to estimate expected radiation fields. Non-linear curve fitting techniques were used to predict exposure rate profiles from cylindrical sources using closed form equations for lines and disks. This information becomes the basis for Safety Analysis Report dose rate estimates and for present and future ALARA design reviews when attempts are made to reduce worker doses.

Analysis of flexible aircraft longitudinal dynamics and handling qualities. Volume 2: Data

NASA Technical Reports Server (NTRS)

Waszak, M. R.; Schmidt, D. K.

1985-01-01

Two analysis methods are applied to a family of flexible aircraft in order to investigate how and when structural (especially dynamic aeroelastic) effects affect the dynamic characteristics of aircraft. The first type of analysis is an open loop modal analysis technique. This method considers the effect of modal residue magnitudes on determining vehicle handling qualities. The second method is a pilot in the loop analysis procedure that considers several closed loop system characteristics. Both analyses indicated that dynamic aeroelastic effects caused a degradation in vehicle tracking performance, based on the evaluation of some simulation results. Volume 2 consists of the presentation of the state variable models of the flexible aircraft configurations used in the analysis applications mode shape plots for the structural modes, numerical results from the modal analysis frequency response plots from the pilot in the loop analysis and a listing of the modal analysis computer program.

Comparing Two Methods for Reducing Variability in Voice Quality Measurements

ERIC Educational Resources Information Center

Kreiman, Jody; Gerratt, Bruce R.

2011-01-01

Purpose: Interrater disagreements in ratings of quality plague the study of voice. This study compared 2 methods for handling this variability. Method: Listeners provided multiple breathiness ratings for 2 sets of pathological voices, one including 20 male and 20 female voices unselected for quality and one including 20 breathy female voices.…

Illinois Quality Counts: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Illinois' Quality Counts prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family…

The UNO Aviation Monograph Series: The Airline Quality Rating 1997

NASA Technical Reports Server (NTRS)

Bowen, Brent D.; Headley, Dean E.

1997-01-01

The Airline Quality Rating (AQR) was developed and first announced in early 1991 as an objective method of comparing airline performance on combined multiple factors important to consumers. Development history and calculation details for the AQR rating system are detailed in The Airline Quality Rating 1991 issued in April, 1991, by the National Institute for Aviation Research at Wichita State University. This current report, Airline Rating 1997, contains monthly Airline Quality Rating scores for 1996. Additional copies are available by contacting Wichita State University or the University of Nebraska at Omaha. The Airline Quality Rating (AQR) 1997 is a summary of a month-by-month quality ratings for the nine major domestic U.S. airlines operating during 1996. Using the Airline Quality Rating system and monthly performance data for each airline for the calendar year of 1996, individual and comparative ratings are reported. This research monograph contains a brief summary of the AQR methodology, detailed data and charts that track comparative quality for major domestic airlines across the 12 month period of 1996, and industry average results. Also comparative Airline Quality Rating data for 1991 through 1995 are included to provide a longer term view of quality in the industry.

Quality Rating and Improvement System State Evaluations and Research

ERIC Educational Resources Information Center

Ferguson, Daniel

2016-01-01

A quality rating and improvement system (QRIS) is a method used by states and local jurisdictions to assess the level of quality of child care and early education programs, improve quality, and convey quality ratings to parents and other consumers. A typical QRIS incorporates the following components: quality standards for participating providers;…

Ergonomics of disposable handles for minimally invasive surgery.

PubMed

Büchel, D; Mårvik, R; Hallabrin, B; Matern, U

2010-05-01

The ergonomic deficiencies of currently available minimally invasive surgery (MIS) instrument handles have been addressed in many studies. In this study, a new ergonomic pistol handle concept, realized as a prototype, and two disposable ring handles were investigated according to ergonomic properties set by new European standards. In this study, 25 volunteers performed four practical tasks to evaluate the ergonomics of the handles used in standard operating procedures (e.g., measuring a suture and cutting to length, precise maneuvering and targeting, and dissection of a gallbladder). Moreover, 20 participants underwent electromyography (EMG) tests to measure the muscle strain they experienced while carrying out the basic functions (grasp, rotate, and maneuver) in the x, y, and z axes. The data measured included the number of errors, the time required for task completion, perception of pressure areas, and EMG data. The values for usability in the test were effectiveness, efficiency, and user satisfaction. Surveys relating to the subjective rating were completed after each task for each of the three handles tested. Each handle except the new prototype caused pressure areas and pain. Extreme differences in muscle strain could not be observed for any of the three handles. Experienced surgeons worked more quickly with the prototype when measuring and cutting a suture (approximately 20%) and during precise maneuvering and targeting (approximately 20%). On the other hand, they completed the dissection task faster with the handle manufactured by Ethicon. Fewer errors were made with the prototype in dissection of the gallbladder. In contrast to the handles available on the market, the prototype was always rated as positive by the volunteers in the subjective surveys. None of the handles could fulfil all of the requirements with top scores. Each handle had its advantages and disadvantages. In contrast to the ring handles, the volunteers could fulfil most of the tasks more

Differential seed handling by two African primates affects seed fate and establishment of large-seeded trees

NASA Astrophysics Data System (ADS)

Gross-Camp, Nicole D.; Kaplin, Beth A.

2011-11-01

We examined the influence of seed handling by two semi-terrestrial African forest primates, chimpanzees ( Pan troglodytes) and l'Hoest's monkeys ( Cercopithecus lhoesti), on the fate of large-seeded tree species in an afromontane forest. Chimpanzees and l'Hoest's monkeys dispersed eleven seed species over one year, with quantity and quality of dispersal varying through time. Primates differed in their seed handling behaviors with chimpanzees defecating large seeds (>0.5 cm) significantly more than l'Hoest's. Furthermore, they exhibited different oral-processing techniques with chimpanzees discarding wadges containing many seeds and l'Hoest's monkeys spitting single seeds. A PCA examined the relationship between microhabitat characteristics and the site where primates deposited seeds. The first two components explained almost half of the observed variation. Microhabitat characteristics associated with sites where seeds were defecated had little overlap with those characteristics describing where spit seeds arrived, suggesting that seed handling in part determines the location where seeds are deposited. We monitored a total of 552 seed depositions through time, recording seed persistence, germination, and establishment. Defecations were deposited significantly farther from an adult conspecific than orally-discarded seeds where they experienced the greatest persistence but poorest establishment. In contrast, spit seeds were deposited closest to an adult conspecific but experienced the highest seed establishment rates. We used experimental plots to examine the relationship between seed handling, deposition site, and seed fate. We found a significant difference in seed handling and fate, with undispersed seeds in whole fruits experiencing the lowest establishment rates. Seed germination differed by habitat type with open forest experiencing the highest rates of germination. Our results highlight the relationship between primate seed handling and deposition site and seed

Clinical quality is independently associated with favorable bond ratings.

PubMed

Haydar, Ziad; Nicewander, David; Convery, Paul; Black, Michael; Ballard, David

2010-01-01

The relation between clinical quality and bond rating for nonprofit hospitals has been proposed but never fully studied. We analyzed the relation between bond rating, clinical quality measures (The Joint Commission/Centers for Medicare and Medicaid Services [CMS] core measures), and balance sheet and income statement financial measures of 236 hospitals across the United States that are rated by Moody's Investors Service and that reported clinical quality measures to CMS during the study period. We found a statistically significant relation between higher quality measures and more favorable bond ratings. This association remained significant after controlling for traditional financial parameters.

AVIRIS onboard data handling and control

NASA Technical Reports Server (NTRS)

Steinkraus, Ronald E.; Hickok, Roger W.

1987-01-01

The timing and flow of detector and ancillary data for the Airborne Visible/Infrared imaging spectrometer (AVIRIS) are controlled within the instrument by its digital electronics assembly. In addition to providing detector and signal chain timing, the digital electronics receives, formats, and rate-buffers digitized science data; collects and formats ancillary (calibration and engineering) data; and merges both into a single tape record. Overall AVIRIS data handling is effected by a combination of dedicated digital electronics to control instrument timing, image data flow, and data rate buffering and a microcomputer programmed to handle real-time control of instrument mechanisms and the coordinated preparation of ancillary data.

Subjective quality evaluation of low-bit-rate video

NASA Astrophysics Data System (ADS)

Masry, Mark; Hemami, Sheila S.; Osberger, Wilfried M.; Rohaly, Ann M.

2001-06-01

A subjective quality evaluation was performed to qualify vie4wre responses to visual defects that appear in low bit rate video at full and reduced frame rates. The stimuli were eight sequences compressed by three motion compensated encoders - Sorenson Video, H.263+ and a Wavelet based coder - operating at five bit/frame rate combinations. The stimulus sequences exhibited obvious coding artifacts whose nature differed across the three coders. The subjective evaluation was performed using the Single Stimulus Continuos Quality Evaluation method of UTI-R Rec. BT.500-8. Viewers watched concatenated coded test sequences and continuously registered the perceived quality using a slider device. Data form 19 viewers was colleted. An analysis of their responses to the presence of various artifacts across the range of possible coding conditions and content is presented. The effects of blockiness and blurriness on perceived quality are examined. The effects of changes in frame rate on perceived quality are found to be related to the nature of the motion in the sequence.

Effect of ramp configuration on easiness of handling, heart rate, and behavior of near-market weight pigs at unloading.

PubMed

Goumon, S; Faucitano, L; Bergeron, R; Crowe, T; Connor, M L; Gonyou, H W

2013-08-01

Three experiments, each using 280 pigs, were conducted in a simulated compartment to test the effect of angle of entrance (AOE) to the ramp (90°, 60°, 30°, or 0°), ramp slope (0°, 16°, 21°, or 26°), and an initial 20-cm step associated with 16° or 21° ramp slopes on the ease of handling, heart rate (HR), and behavior of near market-weight pigs during unloading. Heart rate (pigs and handler), unloading time, interventions of the handler, and reactions of the pigs were monitored. The results of the first experiment show that using a 90° AOE had detrimental effects on ease of handling (P < 0.05), HR of the pig (P < 0.05), and behavior (P < 0.05). The 0° and 30° AOE appeared to improve the ease of unloading, whereas the 60° AOE had an intermediate effect. The 30° AOE appeared to be preferable, because pigs moved at this angle balked less frequently (P < 0.01) and required less manipulation (P < 0.05) than pigs moved with a 0° AOE. The results of the second experiment show that the use of a flat ramp led to the easiest unloading, as demonstrated by the lower number of balks (P < 0.001) when pigs were moved to the ramp and less frequent use of paddle (P = 0.001) or voice (P < 0.001) on the ramp, compared with the other treatments. However, the flat ramp did not differ from the 21° ramp in many of the variables reflecting ease of handling, which may be explained by the difference in configuration between the ramps. The results also show that the use of the steepest ramp slope had the most detrimental effect on balking and backing up behavior of pigs (P < 0.001), and handling (touches, slaps, and pushes; P < 0.05 for all) when moved to the ramp and on unloading time (P < 0.01). No differences in pig HR (P < 0.05) and ease of handling on the ramp (P < 0.05) were found between a 26° and 16° ramp slope, suggesting that the length of the ramp may be one of the factors that make unloading more difficult. The results of the last experiment show that an initial

Handling Qualities Evaluations of Low Complexity Model Reference Adaptive Controllers for Reduced Pitch and Roll Damping Scenarios

NASA Technical Reports Server (NTRS)

Hanson, Curt; Schaefer, Jacob; Burken, John J.; Johnson, Marcus; Nguyen, Nhan

2011-01-01

National Aeronautics and Space Administration (NASA) researchers have conducted a series of flight experiments designed to study the effects of varying levels of adaptive controller complexity on the performance and handling qualities of an aircraft under various simulated failure or damage conditions. A baseline, nonlinear dynamic inversion controller was augmented with three variations of a model reference adaptive control design. The simplest design consisted of a single adaptive parameter in each of the pitch and roll axes computed using a basic gradient-based update law. A second design was built upon the first by increasing the complexity of the update law. The third and most complex design added an additional adaptive parameter to each axis. Flight tests were conducted using NASA s Full-scale Advanced Systems Testbed, a highly modified F-18 aircraft that contains a research flight control system capable of housing advanced flight controls experiments. Each controller was evaluated against a suite of simulated failures and damage ranging from destabilization of the pitch and roll axes to significant coupling between the axes. Two pilots evaluated the three adaptive controllers as well as the non-adaptive baseline controller in a variety of dynamic maneuvers and precision flying tasks designed to uncover potential deficiencies in the handling qualities of the aircraft, and adverse interactions between the pilot and the adaptive controllers. The work was completed as part of the Integrated Resilient Aircraft Control Project under NASA s Aviation Safety Program.

Virginia Star Quality Initiative: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Virginia's Star Quality Initiative prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators…

Mississippi Quality Step System: QRS Profile. The Child Care Quality Rating System (QRS)Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Mississippi's Quality Step System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Application…

Effect of lift-to-drag ratio in pilot rating of the HL-20 landing task

NASA Technical Reports Server (NTRS)

Jackson, E. B.; Rivers, Robert A.; Bailey, Melvin L.

1993-01-01

A man-in-the-loop simulation study of the handling qualities of the HL-20 lifting-body vehicle was made in a fixed-base simulation cockpit at NASA Langley Research Center. The purpose of the study was to identify and substantiate opportunities for improving the original design of the vehicle from a handling qualities and landing performance perspective. Using preliminary wind-tunnel data, a subsonic aerodynamic model of the HL-20 was developed. This model was adequate to simulate the last 75-90 s of the approach and landing. A simple flight-control system was designed and implemented. Using this aerodynamic model as a baseline, visual approaches and landings were made at several vehicle lift-to-drag ratios. Pilots rated the handling characteristics of each configuration using a conventional numerical pilot-rating scale. Results from the study showed a high degree of correlation between the lift-to-drag ratio and pilot rating. Level 1 pilot ratings were obtained when the L/D ratio was approximately 3.8 or higher.

Effect of lift-to-drag ratio in pilot rating of the HL-20 landing task

NASA Astrophysics Data System (ADS)

Jackson, E. B.; Rivers, Robert A.; Bailey, Melvin L.

1993-10-01

A man-in-the-loop simulation study of the handling qualities of the HL-20 lifting-body vehicle was made in a fixed-base simulation cockpit at NASA Langley Research Center. The purpose of the study was to identify and substantiate opportunities for improving the original design of the vehicle from a handling qualities and landing performance perspective. Using preliminary wind-tunnel data, a subsonic aerodynamic model of the HL-20 was developed. This model was adequate to simulate the last 75-90 s of the approach and landing. A simple flight-control system was designed and implemented. Using this aerodynamic model as a baseline, visual approaches and landings were made at several vehicle lift-to-drag ratios. Pilots rated the handling characteristics of each configuration using a conventional numerical pilot-rating scale. Results from the study showed a high degree of correlation between the lift-to-drag ratio and pilot rating. Level 1 pilot ratings were obtained when the L/D ratio was approximately 3.8 or higher.

Palm Beach Quality Counts: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Palm Beach's Quality Counts prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

Maine Quality for ME: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Maine's Quality for ME prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family…

Miami-Dade Quality Counts: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Miami-Dade's Quality Counts prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

Indiana Paths to Quality: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Indiana's Paths to Quality prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

The development and potential of inverse simulation for the quantitative assessment of helicopter handling qualities

NASA Technical Reports Server (NTRS)

Bradley, Roy; Thomson, Douglas G.

1993-01-01

In this paper it is proposed that inverse simulation can make a positive contribution to the study of handling qualities. It is shown that mathematical descriptions of the MTEs (Mission Task Elements) defined in ADS-33C may be used to drive an inverse simulation thereby generating, from an appropriate mathematical model, the controls and states of a subject helicopter flying it. By presenting the results of such simulations it is shown that, in the context of inverse simulation, the attitude quickness parameters given in ADS-33C are independent of vehicle configuration. An alternative quickness parameter, associated with the control displacements required to fly the MTE is proposed, and some preliminary results are presented.

Cottonseed air-handling and storage requirements

USDA-ARS?s Scientific Manuscript database

In addition to lint, cottonseed is an additional product of the cotton plant that accounts for 15 to 25 percent of the crop value. Due to the value of the cottonseed, proper handling, storage, and aeration are critical for maintaining seed quality and minimizing spoilage. Over the last few decades,...

Quality Rating Systems--The Experiences of Center Directors

ERIC Educational Resources Information Center

Friedman, Dana E.

2007-01-01

Quality Rating System (QRS) initiatives define levels of quality based on research and then support providers with funding and technical assistance to increase their quality. Each program is assessed and given a number of "stars" to indicate to parents what level of quality the program has reached. In this article, the author describes…

An analytical study of electric vehicle handling dynamics

NASA Technical Reports Server (NTRS)

Greene, J. E.; Segal, D. J.

1979-01-01

Hypothetical electric vehicle configurations were studied by applying available analytical methods. Elementary linearized models were used in addition to a highly sophisticated vehicle dynamics computer simulation technique. Physical properties of specific EV's were defined for various battery and powertrain packaging approaches applied to a range of weight distribution and inertial properties which characterize a generic class of EV's. Computer simulations of structured maneuvers were performed for predicting handling qualities in the normal driving range and during various extreme conditions related to accident avoidance. Results indicate that an EV with forward weight bias will possess handling qualities superior to a comparable EV that is rear-heavy or equally balanced. The importance of properly matching tires, suspension systems, and brake system front/rear torque proportioning to a given EV configuration during the design stage is demonstrated.

Getting a Handle on Academic Quality

ERIC Educational Resources Information Center

Massy, William F.; Graham, Steven W.; Short, Paula Myrick

2007-01-01

The quality of teaching, more than ever, is seen as the all-important results area for colleges and universities. Few board members would dispute the importance of teaching or their responsibility for exercising oversight over its quality and continuous improvement. Yet there is little consensus about how to accomplish such oversight. Few board…

Ohio Step Up to Quality: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Ohio's Step Up to Quality prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family…

Riding and handling qualities of light aircraft: A review and analysis

NASA Technical Reports Server (NTRS)

Smetana, F. O.; Summery, D. C.; Johnson, W. D.

1972-01-01

Design procedures and supporting data necessary for configuring light aircraft to obtain desired responses to pilot commands and gusts are presented. The procedures employ specializations of modern military and jet transport practice where these provide an improvement over earlier practice. General criteria for riding and handling qualities are discussed in terms of the airframe dynamics. Methods available in the literature for calculating the coefficients required for a linearized analysis of the airframe dynamics are reviewed in detail. The review also treats the relation of spin and stall to airframe geometry. Root locus analysis is used to indicate the sensitivity of airframe dynamics to variations in individual stability derivatives and to variations in geometric parameters. Computer programs are given for finding the frequencies, damping ratios, and time constants of all rigid body modes and for generating time histories of aircraft motions in response to control inputs. Appendices are included presenting the derivation of the linearized equations of motion; the stability derivatives; the transfer functions; approximate solutions for the frequency, damping ratio, and time constants; an indication of methods to be used when linear analysis is inadequate; sample calculations; and an explanation of the use of root locus diagrams and Bode plots.

Adverse risk: a 'dynamic interaction model of patient moving and handling'.

PubMed

Griffiths, Howard

2012-09-01

The aim of the present study was to examine patient adverse events associated with sub-optimal patient moving and handling. Few studies have examined the patient's perspective on adverse risk during manual handling episodes. A narrative review was undertaken to develop the 'Dynamic Interaction Model of Patient Moving and Handling' in an orthopaedic rehabilitation setting, using peer-reviewed publications published in English between 1992 and 2010. Five predominant themes emerged from the narrative review: 'patient's need to know about analgesics prior to movement/ambulation'; 'comfort care'; 'mastery of and acceptance of mobility aids/equipment'; 'psychological adjustment to fear of falling'; and 'the need for movement to prevent tissue pressure damage'. Prevalence of discomfort, pain, falls, pressure sores together with a specific Direct Instrument Nursing Observation (DINO) tool enable back care advisers to measure quality of patient manual handling. Evaluation of patients' use of mobility aids together with fear of falling may be important in determining patients' recovery trajectory. Clinical governance places a responsibility on nurse managers to consider quality of care for their service users. 'Dynamic Interaction Model of Nurse-Patient Moving and Handling' provides back care advisers, clinical risk managers and occupational health managers with an alternative perspective to clinical risk and occupational risk. © 2011 Blackwell Publishing Ltd.

45 CFR 156.1120 - Quality rating system.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 45 Public Welfare 1 2014-10-01 2014-10-01 false Quality rating system. 156.1120 Section 156.1120 Public Welfare Department of Health and Human Services REQUIREMENTS RELATING TO HEALTH CARE ACCESS HEALTH INSURANCE ISSUER STANDARDS UNDER THE AFFORDABLE CARE ACT, INCLUDING STANDARDS RELATED TO EXCHANGES Quality...

Space shuttle data handling and communications considerations.

NASA Technical Reports Server (NTRS)

Stoker, C. J.; Minor, R. G.

1971-01-01

Operational and development flight instrumentation, data handling subsystems and communication requirements of the space shuttle orbiter are discussed. Emphasis is made on data gathering methods, crew display data, computer processing, recording, and telemetry by means of a digital data bus. Also considered are overall communication conceptual system aspects and design features allowing a proper specification of telemetry encoders and instrumentation recorders. An adaptive bit rate concept is proposed to handle the telemetry bit rates which vary with the amount of operational and experimental data to be transmitted. A split-phase encoding technique is proposed for telemetry to cope with the excessive bit jitter and low bit transition density which may affect television performance.

Quality Improvement Efforts among Early Childhood Education Programs Participating in Iowa's Quality Rating System. REL 2017-244

ERIC Educational Resources Information Center

Hawkinson, Laura E.; Faria, Ann-Marie; Bouacha, Nora; Lee, Dong Hoon; Metzger, Ivan

2017-01-01

This report describes the quality improvement efforts of early childhood education programs participating in Iowa's Quality Rating System (QRS). It identifies supports and barriers to quality improvement and examines how quality improvement supports and activities relate to changes in program quality ratings across time. The study team developed…

Rating the Quality of Open Textbooks: How Reviewer and Text Characteristics Predict Ratings

ERIC Educational Resources Information Center

Fischer, Lane; Ernst, David; Mason, Stacie

2017-01-01

Using data collected from peer reviews for Open Textbook Library titles, this paper explores questions about rating the quality of open textbooks. The five research questions addressed the relationship between textbook and reviewer characteristics and ratings. Although reviewers gave textbooks high ratings generally, reviewers identified…

Barriers and Facilitators to Safe Food Handling among Consumers: A Systematic Review and Thematic Synthesis of Qualitative Research Studies

PubMed Central

Young, Ian; Waddell, Lisa

2016-01-01

Foodborne illness has a substantial health and economic burden on society, and most cases are believed to be due to unsafe food handling practices at home. Several qualitative research studies have been conducted to investigate consumers’ perspectives, opinions, and experiences with safe food handling at home, and these studies provide insights into the underlying barriers and facilitators affecting their safe food handling behaviours. We conducted a systematic review of previously published qualitative studies in this area to synthesize the main across-study themes and to develop recommendations for future consumer interventions and research. The review was conducted using the following steps: comprehensive search strategy; relevance screening of abstracts; relevance confirmation of articles; study quality assessment; thematic synthesis of the results; and quality-of-evidence assessment. A total of 39 relevant articles reporting on 37 unique qualitative studies were identified. Twenty-one barriers and 10 facilitators to safe food handling were identified, grouped across six descriptive themes: confidence and perceived risk; knowledge-behaviour gap; habits and heuristics; practical and lifestyle constraints; food preferences; and societal and social influences. Our overall confidence that each barrier and facilitator represents the phenomenon of interest was rated as high (n = 11), moderate (11), and low (9). Overarching analytical themes included: 1) safe food handling behaviours occur as part of a complex interaction of everyday consumer practices and habituation; 2) most consumers are not concerned about food safety and are generally not motivated to change their behaviours based on new knowledge about food safety risks; and 3) consumers are amenable to changing their safe food handling habits through relevant social pressures. Key implications and recommendations for research, policy and practice are discussed. PMID:27907161

Evaluation of hygiene practices and microbiological quality of cooked meat products during slicing and handling at retail.

PubMed

Pérez-Rodríguez, F; Castro, R; Posada-Izquierdo, G D; Valero, A; Carrasco, E; García-Gimeno, R M; Zurera, G

2010-10-01

Cooked meat ready-to-eat products are recognized to be contaminated during slicing which, in the last years, has been associated with several outbreaks. This work aimed to find out possible relation between the hygiene practice taking place at retail point during slicing of cooked meat products in small and medium-sized establishments (SMEs) and large-sized establishments (LEs) and the microbiological quality of sliced cooked meat products. For that, a checklist was drawn up and filled in based on scoring handling practice during slicing in different establishments in Cordoba (Southern Spain). In addition, sliced cooked meats were analyzed for different microbiological indicators and investigated for the presence of Listeria spp. and Listeria monocytogenes. Results indicated that SMEs showed a more deficient handling practices compared to LEs. In spite of these differences, microbiological counts indicated similar microbiological quality in cooked meat samples for both types of establishments. On the other hand, Listeria monocytogenes and Listeria inocua were isolated from 7.35% (5/68) and 8.82% (6/68) of analyzed samples, respectively. Positive samples for Listeria spp. were found in establishments which showed acceptable hygiene levels, though contamination could be associated to the lack of exclusiveness of slicers at retail points. Moreover, Listeria spp presence could not be statistically linked to any microbiological parameters; however, it was observed that seasonality influenced significantly (P<0.05) L. monocytogenes presence, being all samples found during warm season (5/5). As a conclusion, results suggested that more effort should be made to adequately educate handlers in food hygiene practices, focused specially on SMEs. Copyright (c) 2010 Elsevier B.V. All rights reserved.

North Carolina Star Rated License System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of North Carolina's Star Rated License System prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4)…

Technical efficiency of nursing homes: do five-star quality ratings matter?

PubMed

Dulal, Rajendra

2017-02-28

This study investigates associations between five-star quality ratings and technical efficiency of nursing homes. The sample consists of a balanced panel of 338 nursing homes in California from 2009 through 2013 and uses two-stage data envelopment (DEA) analysis. The first-stage applies an input oriented variable returns to scale DEA analysis. The second-stage uses a left censored random-effect Tobit regression model. The five-star quality ratings i.e., health inspections, quality measures, staffing available on the Nursing Home Compare website are divided into two categories: outcome and structure form of quality. Results show that quality measures ratings and health inspection ratings, used as outcome form of quality, are not associated with mean technical efficiency. These quality ratings, however, do affect the technical efficiency of a particular nursing home and hence alter the ranking of nursing homes based on efficiency scores. Staffing rating, categorized as a structural form of quality, is negatively associated with mean technical efficiency. These findings show that quality dimensions are associated with technical efficiency in different ways, suggesting that multiple dimensions of quality should be included in the efficiency analysis of nursing homes. They also suggest that patient care can be enhanced through investing more in improving care delivery rather than simply raising the number of staff per resident.

Wood Products by Species and Quality in Upland Forests

Treesearch

David W. Patterson

2004-01-01

Products that can be produced from an upland forest depend on the species and quality of the trees present. Quality depends on growth rate and tree form. These variables are discussed as well as the products that can be produced such as veneer and plywood, grade lumber, handle stock, pallet stock, cross ties, and industrial lumber.

Reducing Mouse Anxiety during Handling: Effect of Experience with Handling Tunnels

PubMed Central

Gouveia, Kelly; Hurst, Jane L.

2013-01-01

Handling stress is a well-recognised source of variation in animal studies that can also compromise the welfare of research animals. To reduce background variation and maximise welfare, methods that minimise handling stress should be developed and used wherever possible. Recent evidence has shown that handling mice by a familiar tunnel that is present in their home cage can minimise anxiety compared with standard tail handling. As yet, it is unclear whether a tunnel is required in each home cage to improve response to handling. We investigated the influence of prior experience with home tunnels among two common strains of laboratory mice: ICR(CD-1) and C57BL/6. We compared willingness to approach the handler and anxiety in an elevated plus maze test among mice picked up by the tail, by a home cage tunnel or by an external tunnel shared between cages. Willingness to interact with the handler was much greater for mice handled by a tunnel, even when this was unfamiliar, compared to mice picked up by the tail. Once habituated to handling, C57BL/6 mice were most interactive towards a familiar home tunnel, whereas the ICR strain showed strong interaction with all tunnel handling regardless of any experience of a home cage tunnel. Mice handled by a home cage or external tunnel showed less anxiety in an elevated plus maze than those picked up by the tail. This study shows that using a tunnel for routine handling reduces anxiety among mice compared to tail handling regardless of prior familiarity with tunnels. However, as home cage tunnels can further improve response to handling in some mice, we recommend that mice are handled with a tunnel provided in their home cage where possible as a simple practical method to minimise handling stress. PMID:23840458

Reducing mouse anxiety during handling: effect of experience with handling tunnels.

PubMed

Gouveia, Kelly; Hurst, Jane L

2013-01-01

Handling stress is a well-recognised source of variation in animal studies that can also compromise the welfare of research animals. To reduce background variation and maximise welfare, methods that minimise handling stress should be developed and used wherever possible. Recent evidence has shown that handling mice by a familiar tunnel that is present in their home cage can minimise anxiety compared with standard tail handling. As yet, it is unclear whether a tunnel is required in each home cage to improve response to handling. We investigated the influence of prior experience with home tunnels among two common strains of laboratory mice: ICR(CD-1) and C57BL/6. We compared willingness to approach the handler and anxiety in an elevated plus maze test among mice picked up by the tail, by a home cage tunnel or by an external tunnel shared between cages. Willingness to interact with the handler was much greater for mice handled by a tunnel, even when this was unfamiliar, compared to mice picked up by the tail. Once habituated to handling, C57BL/6 mice were most interactive towards a familiar home tunnel, whereas the ICR strain showed strong interaction with all tunnel handling regardless of any experience of a home cage tunnel. Mice handled by a home cage or external tunnel showed less anxiety in an elevated plus maze than those picked up by the tail. This study shows that using a tunnel for routine handling reduces anxiety among mice compared to tail handling regardless of prior familiarity with tunnels. However, as home cage tunnels can further improve response to handling in some mice, we recommend that mice are handled with a tunnel provided in their home cage where possible as a simple practical method to minimise handling stress.

Ground data handling for Landsat-D. [for thematic mapper

NASA Technical Reports Server (NTRS)

Lynch, T. J.

1977-01-01

The present plans for the Landsat-D ground data handling are described in relationship to the mission objectives and the planned spacecraft system. The end-to-end data system is presented with particular emphasis on the data handling plans for the new instrument, the Thematic Mapper. This instrument generates ten times the amount of data per scene as the present Multispectral Scanner and this resulting data rate and volume are discussed as well as possible new data techniques to handle them - such as image compression.

Compendium of Quality Rating Systems and Evaluations: The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Tout, Kathryn; Starr, Rebecca; Soli, Margaret; Moodie, Shannon; Kirby, Gretchen; Boller, Kimberly

2010-01-01

Quality Rating Systems (QRS) are currently operating, under development, or being piloted in over 25 states or local areas. As the QRS model becomes integrated into the landscape of child care and education service delivery, policy, and the decisions parents make about child care across the United States, there is an increasing need for…

Rates of urbanisation and the resiliency of air and water quality.

PubMed

Duh, Jiunn-Der; Shandas, Vivek; Chang, Heejun; George, Linda A

2008-08-01

Global human population and urban development are increasing at unprecedented rates and creating tremendous stress on local, regional, and global air and water quality. However, little is known about how urban areas vary in their capacity to address effectively air and water quality impacts associated to urban development. There exists a need to better understanding the factors that mediate the interactions between urbanisation and variations of environmental quality. By synthesizing literatures on the relationship between urban development and air and water quality, we assess the amount of scholarship for each of these cities, characterize population growth rates in one hundred of the largest global cities, and link growth trends to changes in air and water quality. Our results suggest that, while there is a growing literature linking urbanisation and environmental quality, some regions of the globe are better represented than others, and that these trends are consistent with our characterization of population growth rates. In addition, the comparison between population growth rates and air and water quality suggest that multiple factors affect the environmental quality, and that approaching rates of urbanisation through the lens of 'resiliency' can be an effective integrative concept for studying the capacity of urban areas to respond to rapid rates of change. Based on these results we offer a framework for systematically assessing changes in air and water quality in megacities.

Comparing Cultural Differences in Two Quality Measures in Chinese Kindergartens: The Early Childhood Environment Rating Scale-Revised and the Kindergarten Quality Rating System

ERIC Educational Resources Information Center

Hu, Bi Ying

2015-01-01

This study examined the degrees of congruence between two early childhood evaluation systems on various quality concepts: the Early Childhood Environment Rating Scale-Revised (ECERS-R) and Zhejiang's Kindergarten Quality Rating System (KQRS). Analysis of variance and post hoc least significant difference tests were employed to show the extent to…

Tennessee Star-Quality Child Care Program: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Tennessee's Star-Quality Child Care Program prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4)…

Oregon Child Care Quality Indicators Program: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Oregon's Child Care Quality Indicators Program prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4)…

Examining Pre-School Classroom Quality in a Statewide Quality Rating and Improvement System

ERIC Educational Resources Information Center

Jeon, Lieny; Buettner, Cynthia K.; Hur, Eunhye

2014-01-01

Background: Research has documented the importance of high-quality early childhood experiences in preparing children for school. Quality rating and improvement systems (QRIS) have recently emerged in many states as a way to build quality of child care and to promote better child outcomes. Objective: The goal of this study was to determine if…

Developing a workstation-based, real-time simulation for rapid handling qualities evaluations during design

NASA Technical Reports Server (NTRS)

Anderson, Frederick; Biezad, Daniel J.

1994-01-01

This paper describes the Rapid Aircraft DynamIcs AssessmeNt (RADIAN) project - an integration of the Aircraft SYNThesis (ACSTNT) design code with the USAD DATCOM code that estimates stability derivatives. Both of these codes are available to universities. These programs are then linked to flight simulation and flight controller synthesis tools and resulting design is evaluated on a graphics workstation. The entire process reduces the preliminary design time by an order of magnitude and provides an initial handling qualities evaluation of the design coupled to a control law. The integrated design process is applicable to both conventional aircraft taken from current textbooks and to unconventional designs emphasizing agility and propulsive control of attitude. The interactive and concurrent nature of the design process has been well received by industry and by design engineers at NASA. The process is being implemented into the design curriculum and is being used by students who view it as a significant advance over prior methods.

Interpreting the handling qualities of aircraft with stability and control augmentation

NASA Technical Reports Server (NTRS)

Hodgkinson, J.; Potsdam, E. H.; Smith, R. E.

1990-01-01

The general process of designing an aircraft for good flying qualities is first discussed. Lessons learned are pointed out, with piloted evaluation emerging as a crucial element. Two sources of rating variability in performing these evaluations are then discussed. First, the finite endpoints of the Cooper-Harper scale do not bias parametric statistical analyses unduly. Second, the wording of the scale does introduce some scatter. Phase lags generated by augmentation systems, as represented by equivalent time delays, often cause poor flying qualities. An analysis is introduced which allows a designer to relate any level of time delay to a probability of loss of aircraft control. This view of time delays should, it is hoped, allow better visibility of the time delays in the design process.

Handle grip span for optimising finger-specific force capability as a function of hand size.

PubMed

Lee, Soo-Jin; Kong, Yong-Ku; Lowe, Brian D; Song, Seongho

2009-05-01

Five grip spans (45 to 65 mm) were tested to evaluate the effects of handle grip span and user's hand size on maximum grip strength, individual finger force and subjective ratings of comfort using a computerised digital dynamometer with independent finger force sensors. Forty-six males participated and were assigned into three hand size groups (small, medium, large) according to their hands' length. In general, results showed the 55- and 50-mm grip spans were rated as the most comfortable sizes and showed the largest grip strength (433.6 N and 430.8 N, respectively), whereas the 65-mm grip span handle was rated as the least comfortable size and the least grip strength. With regard to the interaction effect of grip span and hand size, small and medium-hand participants rated the best preference for the 50- to 55-mm grip spans and the least for the 65-mm grip span, whereas large-hand participants rated the 55- to 60-mm grip spans as the most preferred and the 45-mm grip span as the least preferred. Normalised grip span (NGS) ratios (29% and 27%) are the ratios of user's hand length to handle grip span. The NGS ratios were obtained and applied for suggesting handle grip spans in order to maximise subjective comfort as well as gripping force according to the users' hand sizes. In the analysis of individual finger force, the middle finger force showed the highest contribution (37.5%) to the total finger force, followed by the ring (28.7%), index (20.2%) and little (13.6%) finger. In addition, each finger was observed to have a different optimal grip span for exerting the maximum force, resulting in a bow-contoured shaped handle (the grip span of the handle at the centre is larger than the handle at the end) for two-handle hand tools. Thus, the grip spans for two-handle hand tools may be designed according to the users' hand/finger anthropometrics to maximise subjective ratings and performance based on this study. Results obtained in this study will provide guidelines

Manual handling: differences in perceived effort, success rate and kinematics between three different pushing techniques.

PubMed

Varcin, Lynn; Claus, Andrew; van den Hoorn, Wolbert; Hodges, Paul

2015-01-01

This study examined the perceived effort, success rates and kinematics for three push strategies in a simulated lateral patient transfer (horizontal slide). Thirteen healthy subjects (four males) completed three repetition pushing loads of 6, 10 and 14 kg in random order; with a spontaneous push strategy, then with a straight-back bent-knees (squat) strategy and the preparatory pelvic movement ('rockback') strategy in random order. Perceived effort and kinematic parameters measured at the onset of movement and at maximum push excursion were compared between strategies and between loads with repeated measures ANOVA. The spontaneous and 'rockback' strategies achieved the pushing task with less perceived effort across all loads than the squat push (P < 0.001). Only 3/13 participants were successful on all attempts at pushing the 14 kg load using a squat strategy, which contrasted with 12/13 participants when the spontaneous strategy or the 'rockback' strategy was used. Forward movement of the pelvis and forward trunk inclination may be positively associated with lower perceived effort in the push task. Practitioner Summary: In a manual-handling task that simulated a lateral patient transfer (horizontal slide), perceived effort and success rates of three push strategies were compared. A straight-back bent-knees push (squat) strategy demonstrated greater perceived effort and lower success rates than a spontaneous push strategy, or a push strategy with preparatory 'rockback' pelvic movement.

Sprag Handle Wrenches

NASA Technical Reports Server (NTRS)

Vranishm, John M.

2010-01-01

Sprag handle wrenches have been proposed for general applications in which conventional pawl-and-ratchet wrenches and sprag and cam "clickless" wrenches are now used. Sprag handle wrenches are so named because they would include components that would function both as parts of handles and as sprags (roller locking/unlocking components). In comparison with all of the aforementioned conventional wrenches, properly designed sprag handle wrenches could operate with much less backlash; in comparison with the conventional clickless wrenches, sprag handle wrenches could be stronger and less expensive (because the sprags would be larger and more easily controllable than are conventional sprags and cams).

Transportation and handling loads

NASA Technical Reports Server (NTRS)

Ostrem, F. E.

1971-01-01

Criteria and recommended practices are presented for the prediction and verification of transportation and handling loads for the space vehicle structure and for monitoring these loads during transportation and handling of the vehicle or major vehicle segments. Elements of the transportation and handling systems, and the forcing functions and associated loads are described. The forcing functions for common carriers and typical handling devices are assessed, and emphasis is given to the assessment of loads at the points where the space vehicle is supported during transportation and handling. Factors which must be considered when predicting the loads include the transportation and handling medium; type of handling fixture; transport vehicle speed; types of terrain; weather (changes in pressure of temperature, wind, etc.); and dynamics of the transportation modes or handling devices (acceleration, deceleration, and rotations of the transporter or handling device).

Evaluation of Flying Qualities and Guidance Displays for an Advanced Tilt-Wing STOL Transport Aircraft in Final Approach and Landing

NASA Technical Reports Server (NTRS)

Frost, Chad R.; Franklin, James A.; Hardy, Gordon H.

2002-01-01

A piloted simulation was performed on the Vertical Motion Simulator at NASA Ames Research Center to evaluate flying qualities of a tilt-wing Short Take-Off and Landing (STOL) transport aircraft during final approach and landing. The experiment was conducted to assess the design s handling qualities, and to evaluate the use of flightpath-centered guidance for the precision approach and landing tasks required to perform STOL operations in instrument meteorological conditions, turbulence, and wind. Pilots rated the handling qualities to be satisfactory for all operations evaluated except those encountering extreme crosswinds and severe windshear; even in these difficult meteorological conditions, adequate handling qualities were maintained. The advanced flight control laws and guidance displays provided consistent performance and precision landings.

Ground-based and in-flight simulator studies of low-speed handling characteristics of two supersonic cruise transport concepts

NASA Technical Reports Server (NTRS)

Grantham, W. D.; Nguyen, L. T.; Deal, P. L.; Neubauer, M. J.; Smith, P. M.; Gregory, F. D.

1978-01-01

Conventional and powered lift concepts for supersonic approach and landing tasks are considered. Results indicated that the transport concepts had unacceptable low-speed handling qualities with no augmentation, and that in order to achieve satisfactory handling qualities, considerable augmentation was required. The available roll-control power was acceptable for the powered-lift concept.

Consumer evaluation of complaint handling in the Dutch health insurance market

PubMed Central

2011-01-01

Background How companies deal with complaints is a particularly challenging aspect in managing the quality of their service. In this study we test the direct and relative effects of service quality dimensions on consumer complaint satisfaction evaluations and trust in a company in the Dutch health insurance market. Methods A cross-sectional survey design was used. Survey data of 150 members of a Dutch insurance panel who lodged a complaint at their healthcare insurer within the past 12 months were surveyed. The data were collected using a questionnaire containing validated multi-item measures. These measures assess the service quality dimensions consisting of functional quality and technical quality and consumer complaint satisfaction evaluations consisting of complaint satisfaction and overall satisfaction with the company after complaint handling. Respondents' trust in a company after complaint handling was also measured. Using factor analysis, reliability and validity of the measures were assessed. Regression analysis was used to examine the relationships between these variables. Results Overall, results confirm the hypothesized direct and relative effects between the service quality dimensions and consumer complaint satisfaction evaluations and trust in the company. No support was found for the effect of technical quality on overall satisfaction with the company. This outcome might be driven by the context of our study; namely, consumers get in touch with a company to resolve a specific problem and therefore might focus more on complaint satisfaction and less on overall satisfaction with the company. Conclusions Overall, the model we present is valid in the context of the Dutch health insurance market. Management is able to increase consumers' complaint satisfaction, overall satisfaction with the company, and trust in the company by improving elements of functional and technical quality. Furthermore, we show that functional and technical quality do not

Consumer evaluation of complaint handling in the Dutch health insurance market.

PubMed

Wendel, Sonja; de Jong, Judith D; Curfs, Emile C

2011-11-15

How companies deal with complaints is a particularly challenging aspect in managing the quality of their service. In this study we test the direct and relative effects of service quality dimensions on consumer complaint satisfaction evaluations and trust in a company in the Dutch health insurance market. A cross-sectional survey design was used. Survey data of 150 members of a Dutch insurance panel who lodged a complaint at their healthcare insurer within the past 12 months were surveyed. The data were collected using a questionnaire containing validated multi-item measures. These measures assess the service quality dimensions consisting of functional quality and technical quality and consumer complaint satisfaction evaluations consisting of complaint satisfaction and overall satisfaction with the company after complaint handling. Respondents' trust in a company after complaint handling was also measured. Using factor analysis, reliability and validity of the measures were assessed. Regression analysis was used to examine the relationships between these variables. Overall, results confirm the hypothesized direct and relative effects between the service quality dimensions and consumer complaint satisfaction evaluations and trust in the company. No support was found for the effect of technical quality on overall satisfaction with the company. This outcome might be driven by the context of our study; namely, consumers get in touch with a company to resolve a specific problem and therefore might focus more on complaint satisfaction and less on overall satisfaction with the company. Overall, the model we present is valid in the context of the Dutch health insurance market. Management is able to increase consumers' complaint satisfaction, overall satisfaction with the company, and trust in the company by improving elements of functional and technical quality. Furthermore, we show that functional and technical quality do not influence consumer satisfaction evaluations and

Lifting and exertion injuries decrease after implementation of an integrated hospital-wide safe patient handling and mobilisation programme.

PubMed

Dennerlein, Jack T; O'Day, Elizabeth Tucker; Mulloy, Deborah F; Somerville, Jackie; Stoddard, Anne M; Kenwood, Christopher; Teeple, Erin; Boden, Leslie I; Sorensen, Glorian; Hashimoto, Dean

2017-05-01

With increasing emphasis on early and frequent mobilisation of patients in acute care, safe patient handling and mobilisation practices need to be integrated into these quality initiatives. We completed a programme evaluation of a safe patient handling and mobilisation programme within the context of a hospital-wide patient care improvement initiative that utilised a systems approach and integrated safe patient equipment and practices into patient care plans. Baseline and 12-month follow-up surveys of 1832 direct patient care workers assessed work practices and self-reported pain while an integrated employee payroll and injury database provided recordable injury rates collected concurrently at 2 hospitals: the study hospital with the programme and a comparison hospital. Safe and unsafe patient handling practice scales at the study hospital improved significantly (p<0.0001 and p=0.0031, respectively), with no differences observed at the comparison hospital. We observed significant decreases in recordable neck and shoulder (Relative Risk (RR)=0.68, 95% CI 0.46 to 1.00), lifting and exertion (RR=0.73, 95% CI 0.60 to 0.89) and pain and inflammation (RR=0.78, 95% CI 0.62 to 1.00) injury rates at the study hospital. Changes in rates at the comparison hospital were not statistically significant. Within the context of a patient mobilisation initiative, a safe patient handling and mobilisation programme was associated with improved work practices and a reduction in recordable worker injuries. This study demonstrates the potential impact of utilising a systems approach based on recommended best practices, including integration of these practices into the patient's plan for care. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Postproduction Handling and Administration of Protein Pharmaceuticals and Potential Instability Issues.

PubMed

Nejadnik, M Reza; Randolph, Theodore W; Volkin, David B; Schöneich, Christian; Carpenter, John F; Crommelin, Daan J A; Jiskoot, Wim

2018-04-14

The safety and efficacy of protein pharmaceuticals depend not only on biological activity but also on purity levels. Impurities may be process related because of limitations in manufacturing or product related because of protein degradation occurring throughout the life history of a product. Although the pharmaceutical biotechnology industry has made great progress in improving bulk and drug product manufacturing as well as company-controlled storage and transportation conditions to minimize the level of degradation, there is less control over the many factors that may subsequently affect product quality after the protein pharmaceuticals are released and shipped by the manufacturer. Routine handling or unintentional mishandling of therapeutic protein products may cause protein degradation that remains unnoticed but can potentially compromise the clinical safety and efficacy of the product. In this commentary, we address some potential risks associated with (mis)handling of protein pharmaceuticals after release by the manufacturer. We summarize the environmental stress factors that have been shown to cause protein degradation and that may be encountered during typical handling procedures of protein pharmaceuticals in a hospital setting or during self-administration by patients. Moreover, we provide recommendations for improvements in product handling to help ensure the quality of protein pharmaceuticals during use. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Handling and restraint.

PubMed

Donovan, John; Brown, Patricia

2006-07-01

For the safety of the handler and the animal, proper methods for handling and restraining laboratory animals should be followed. Improper handling can result in increased stress and injury to the animal. In addition, the handler risks injury from bite wounds or scratches inflicted when the animal becomes fearful or anxious. By using sure, direct movements with a determined attitude, the animal can be easily handled and restrained. Animals can be restrained either manually or in a plastic restrainer. The protocols in this unit describe handling and manual restraint of mice, rats, hamsters, and rabbits. Alternate protocols describe restraint using the plastic restrainer.

Handling and restraint.

PubMed

Donovan, John; Brown, Patricia

2004-09-01

For the safety of the handler and the animal, proper methods for handling and restraining laboratory animals should be followed. Improper handling can result in increased stress and injury to the animal. In addition, the handler risks injury from bite wounds or scratches inflicted when the animal becomes fearful or anxious. By using sure, direct movements with a determined attitude, the animal can be easily handled and restrained. Animals can be restrained either manually or in a plastic restrainer. The protocols in this unit describe handling and manual restraint of mice, rats, hamsters, and rabbits. Alternate protocols describe restraint using the plastic restrainer.

A helicopter handling-qualities study of the effects of engine response characteristics, height-control dynamics, and excess power on nap-of-the-Earth operations

NASA Technical Reports Server (NTRS)

Corliss, L. D.

1982-01-01

The helicopter configuration with an rpm-governed gas-turbine engine was examined. A wide range of engine response time, vehicle damping and sensitivity, and excess power levels was studied. The data are compared with the existing handling-qualities specifications, MIL-F-83300 and AGARD 577, and in general show a need for higher minimums when performing such NOE maneuvers as a dolphin and bob-up task.

Rating methodological quality: toward improved assessment and investigation.

PubMed

Moyer, Anne; Finney, John W

2005-01-01

Assessing methodological quality is considered essential in deciding what investigations to include in research syntheses and in detecting potential sources of bias in meta-analytic results. Quality assessment is also useful in characterizing the strengths and limitations of the research in an area of study. Although numerous instruments to measure research quality have been developed, they have lacked empirically-supported components. In addition, different summary quality scales have yielded different findings when they were used to weight treatment effect estimates for the same body of research. Suggestions for developing improved quality instruments include: distinguishing distinct domains of quality, such as internal validity, external validity, the completeness of the study report, and adherence to ethical practices; focusing on individual aspects, rather than domains of quality; and focusing on empirically-verified criteria. Other ways to facilitate the constructive use of quality assessment are to improve and standardize the reporting of research investigations, so that the quality of studies can be more equitably and thoroughly compared, and to identify optimal methods for incorporating study quality ratings into meta-analyses.

Flying Quality Analysis of a JAS 39 Gripen Ministick Controller in an F/A-18 Aircraft

NASA Technical Reports Server (NTRS)

Carter, John F.; Stoliker, P. C.

2000-01-01

NASA Dryden conducted a handling qualities experiment using a small displacement centerstick controller that Saab-Scania developed for the JAS 39 Gripen aircraft. The centerstick, or ministick, was mounted in the rear cockpit of an F/A-18 aircraft. Production support flight control computers (PSFCC) provided a pilot-selectable research control system. The objectives for this experiment included determining whether the mechanical characteristics of the centerstick controller had any significant effect on the handling qualities of the F/A-18, and determining the usefulness of the PSFCCs for this kind of experiment. Five pilots evaluated closed-loop tracking tasks, including echelon and column formation flight and target following. Cooper-Harper ratings and pilot comments were collected for each maneuver. This paper describes the test system, including the PSFCCs, the Gripen centerstick, and the flight test experiment. The paper presents results of longitudinal handling qualities maneuvers, including low order equivalent systems, Neal-Smith, and controls anticipation parameter analyses. The experiment showed that, while the centerstick controller provided a different aircraft feel, few handling qualities deficiencies resulted. It also demonstrated that the PSFCCs were useful for this kind of investigation.

Quantifying the effect of editor-author relations on manuscript handling times.

PubMed

Sarigöl, Emre; Garcia, David; Scholtes, Ingo; Schweitzer, Frank

2017-01-01

In this article we study to what extent the academic peer review process is influenced by social relations between the authors of a manuscript and the editor handling the manuscript. Taking the open access journal PlosOne as a case study, our analysis is based on a data set of more than 100,000 articles published between 2007 and 2015. Using available data on handling editor, submission and acceptance time of manuscripts, we study the question whether co-authorship relations between authors and the handling editor affect the manuscript handling time , i.e. the time taken between the submission and acceptance of a manuscript. Our analysis reveals (1) that editors handle papers co-authored by previous collaborators significantly more often than expected at random, and (2) that such prior co-author relations are significantly related to faster manuscript handling. Addressing the question whether these shorter manuscript handling times can be explained by the quality of publications, we study the number of citations and downloads which accepted papers eventually accumulate. Moreover, we consider the influence of additional (social) factors, such as the editor's experience, the topical similarity between authors and editors, as well as reciprocal citation relations between authors and editors. Our findings show that, even when correcting for other factors like time, experience, and performance, prior co-authorship relations have a large and significant influence on manuscript handling times, speeding up the editorial decision on average by 19 days.

Testing for handling bias in survival estimation for black brant

USGS Publications Warehouse

Sedinger, J.S.; Lindberg, M.S.; Rexstad, E.A.; Chelgren, N.D.; Ward, D.H.

1997-01-01

We used an ultrastructure approach in program SURVIV to test for, and remove, bias in survival estimates for the year following mass banding of female black brant (Branta bernicla nigricans). We used relative banding-drive size as the independent variable to control for handling effects in our ultrastructure models, which took the form: S = S0(1 - ??D), where ?? was handling effect and D was the ratio of banding-drive size to the largest banding drive. Brant were divided into 3 classes: goslings, initial captures, and recaptures, based on their state at the time of banding, because we anticipated the potential for heterogeneity in model parameters among classes of brant. Among models examined, for which ?? was not constrained, a model with ?? constant across classes of brant and years, constant survival rates among years for initially captured brant but year-specific survival rates for goslings and recaptures, and year- and class-specific detection probabilities had the lowest Akaike Information Criterion (AIC). Handling effect, ??, was -0.47 ?? 0.13 SE, -0.14 ?? 0.057, and -0.12 ?? 0.049 for goslings, initially released adults, and recaptured adults. Gosling annual survival in the first year ranged from 0.738 ?? 0.072 for the 1986 cohort to 0.260 ?? 0.025 for the 1991 cohort. Inclusion of winter observations increased estimates of first-year survival rates by an average of 30%, suggesting that permanent emigration had an important influence on apparent survival, especially for later cohorts. We estimated annual survival for initially captured brant as 0.782 ?? 0.013, while that for recaptures varied from 0.726 ?? 0.034 to 0.900 ?? 0.062. Our analyses failed to detect a negative effect of handling on survival of brant, which is consistent with an hypothesis of substantial inherent heterogeneity in post-fledging survival rates, such that individuals most likely to die as a result of handling also have lower inherent survival probabilities.

Effect on Longitudinal Stability and Control Characteristics of a Boeing B-29 Airplane of Variations in Stick-Force and Control-Rate Characteristics Obtained Through Use of a Booster in the Elevator-Control System

NASA Technical Reports Server (NTRS)

Mathews, Charles W; Talmage, Donald B; Whitten, James B

1952-01-01

A longitudinal stability and control characteristics of a Boeing B-29 airplane have been measured with a booster incorporated in the elevator-control system. Tests were made to determine the effects on the handling qualities of the test airplane of variations in the pilot's control-force gradients as well as the effects of variations in the maximum rate of control motion supplied by the booster. The results of the control-rate investigation indicate that large airplanes may have satisfactory handling qualities with the booster adjusted to give much lower rates of control motion than those normally used by pilots.

Hearing aid handling skills: relationship with satisfaction and benefit.

PubMed

Campos, Patrícia Danieli; Bozza, Amanda; Ferrari, Deborah Viviane

2014-01-01

To evaluate hearing aid handling skills for new and experienced users and to assess if such skills influence user's benefit and satisfaction. Seventy four participants (mean age of 70.43), experienced (n=37) or new hearing aid users (n=37) performed the tasks of "Practical Hearing Aid Skills Test" (PHAST), which were scored on a five-point Likert scale - higher scores indicate better hearing aid handling skills. Experienced users answered the International Outcome Inventory for Hearing Aids (IOI-HA) and the hearing aid benefit for handicap reduction was calculated by the hearing handicap inventory (HHIA/HHIE). Medians for PHAST total scores of 79 and 71% were obtained for experienced and new users, respectively - there were no significant difference between groups. Lower PHAST scores were observed for the tasks of volume control manipulation and telephone usage. Moderate correlations were obtained between IOI benefit and quality of life items and the PHAST scores. There was no correlation between the results of PHAST and demographic data of the participants. There was no difference in handling skills between new and experienced hearing aid users. Handling skills affected hearing aid benefit.

Crystal Growth Rate Dispersion: A Predictor of Crystal Quality in Microgravity?

NASA Technical Reports Server (NTRS)

Kephart, Richard D.; Judge, Russell A.; Snell, Edward H.; vanderWoerd, Mark J.

2003-01-01

In theory macromolecular crystals grow through a process involving at least two transport phenomena of solute to the crystal surface: diffusion and convection. In absence of standard gravitational forces, the ratio of these two phenomena can change and explain why crystal growth in microgravity is different from that on Earth. Experimental evidence clearly shows, however, that crystal growth of various systems is not equally sensitive to reduction in gravitational forces, leading to quality improvement in microgravity for some crystals but not for others. We hypothesize that the differences in final crystal quality are related to crystal growth rate dispersion. If growth rate dispersion exists on Earth, decreases in microgravity, and coincides with crystal quality improvements then this dispersion is a predictor for crystal quality improvement. In order to test this hypothesis, we will measure growth rate dispersion both in microgravity and on Earth and will correlate the data with previously established data on crystal quality differences for the two environments. We present here the first crystal growth rate measurement data for three proteins (lysozyme, xylose isomerase and human recombinant insulin), collected on Earth, using hardware identical to the hardware to be used in microgravity and show how these data correlate with crystal quality improvements established in microgravity.

Musculoskeletal injuries resulting from patient handling tasks among hospital workers.

PubMed

Pompeii, Lisa A; Lipscomb, Hester J; Schoenfisch, Ashley L; Dement, John M

2009-07-01

The purpose of this study was to evaluate musculoskeletal injuries and disorders resulting from patient handling prior to the implementation of a "minimal manual lift" policy at a large tertiary care medical center. We sought to define the circumstances surrounding patient handling injuries and to identify potential preventive measures. Human resources data were used to define the cohort and their time at work. Workers' compensation records (1997-2003) were utilized to identify work-related musculoskeletal claims, while the workers' description of injury was used to identify those that resulted from patient handling. Adjusted rate ratios were generated using Poisson regression. One-third (n = 876) of all musculoskeletal injuries resulted from patient handling activities. Most (83%) of the injury burden was incurred by inpatient nurses, nurses' aides and radiology technicians, while injury rates were highest for nurses' aides (8.8/100 full-time equivalent, FTEs) and smaller workgroups including emergency medical technicians (10.3/100 FTEs), patient transporters (4.3/100 FTEs), operating room technicians (3.1/100 FTEs), and morgue technicians (2.2/100 FTEs). Forty percent of injuries due to lifting/transferring patients may have been prevented through the use of mechanical lift equipment, while 32% of injuries resulting from repositioning/turning patients, pulling patients up in bed, or catching falling patients may not have been prevented by the use of lift equipment. The use of mechanical lift equipment could significantly reduce the risk of some patient handling injuries but additional interventions need to be considered that address other patient handling tasks. Smaller high-risk workgroups should not be neglected in prevention efforts.

Relationships between Medicare Advantage contract characteristics and quality-of-care ratings: an observational analysis of Medicare Advantage star ratings.

PubMed

Xu, Peng; Burgess, James F; Cabral, Howard; Soria-Saucedo, Rene; Kazis, Lewis E

2015-03-03

The Centers for Medicare & Medicaid Services (CMS) publishes star ratings on Medicare Advantage (MA) contracts to measure plan quality of care with implications for reimbursement and bonuses. To investigate whether MA contract characteristics are associated with quality of care through the Medicare plan star ratings. Retrospective study of MA star ratings in 2010. Unadjusted and adjusted multivariable linear regression models assessed the relationship between 5-star rating summary scores and plan characteristics. CMS MA contracts nationally. 409 (71%) of a total of 575 MA contracts, covering 10.56 million Medicare beneficiaries (90% of the MA population) in the United States in 2010. The MA quality ratings summary score (stars range from 1 to 5) is a quality measure based on 36 indicators related to processes of care, health outcomes, access to care, and beneficiary satisfaction. Nonprofit, larger, and older MA contracts were more likely to receive higher star ratings. Star ratings ranged from 2 to 5. Nonprofit contracts received an average 0.55 (95% CI, 0.42 to 0.67) higher star ratings than for-profit contracts (P  < 0.001) after controls were set for contract characteristics. The study focused on persons aged 65 years or older covered by MA. In 2010, nonprofit MA contracts received significantly higher star ratings than for-profit contracts. When comparing health plans in the future, the CMS should give increasing attention to for-profit plans with lower quality ratings and consider developing programs to assist newer and smaller plans in improving their care for Medicare beneficiaries. None.

42 CFR 493.1242 - Standard: Specimen submission, handling, and referral.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 5 2010-10-01 2010-10-01 false Standard: Specimen submission, handling, and referral. 493.1242 Section 493.1242 Public Health CENTERS FOR MEDICARE & MEDICAID SERVICES, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) STANDARDS AND CERTIFICATION LABORATORY REQUIREMENTS Quality System...

7 CFR 996.30 - Incoming quality standards.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Incoming quality standards. 996.30 Section 996.30... Agreements and Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE MINIMUM QUALITY AND HANDLING STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Quality and Handling Standards...

Comparing Public Quality Ratings for Accredited and Nonaccredited Nursing Homes.

PubMed

Williams, Scott C; Morton, David J; Braun, Barbara I; Longo, Beth Ann; Baker, David W

2017-01-01

Compare quality ratings of accredited and nonaccredited nursing homes using the publicly available Centers for Medicare and Medicaid Services (CMS) Nursing Home Compare data set. This cross-sectional study compared the performance of 711 Joint Commission-accredited (TJC-accredited) nursing homes (81 of which also had Post-Acute Care Certification) to 14,926 non-Joint Commission-accredited (non-TJC-accredited) facilities using the Nursing Home Compare data set (as downloaded on April 2015). Measures included the overall Five-Star Quality Rating and its 4 components (health inspection, quality measures, staffing, and RN staffing), the 18 Nursing Home Compare quality measures (5 short-stay measures, 13 long-stay measures), as well as inspection deficiencies, fines, and payment denials. t tests were used to assess differences in rates for TJC-accredited nursing homes versus non-TJC-accredited nursing homes for quality measures, ratings, and fine amounts. Analysis of variance models were used to determine differences in rates using Joint Commission accreditation status, nursing home size based on number of beds, and ownership type. An additional model with an interaction term using Joint Commission accreditation status and Joint Commission Post-Acute Care Certification status was used to determine differences in rates for Post-Acute Care Certified nursing homes. Binary variables (eg, deficiency type, fines, and payment denials) were evaluated using a logistic regression model with the same covariates. After controlling for the influences of facility size and ownership type, TJC-accredited nursing homes had significantly higher star ratings than non-TJC-accredited nursing homes on each of the star rating component subscales (P < .05) (but not on the overall star rating), and TJC-accredited nursing homes with Post-Acute Care Certification performed statistically better on the overall star rating, as well as 3 of the 4 subscales (P < .05). TJC-accredited nursing homes

Enteral Feeding Set Handling Techniques.

PubMed

Lyman, Beth; Williams, Maria; Sollazzo, Janet; Hayden, Ashley; Hensley, Pam; Dai, Hongying; Roberts, Cristine

2017-04-01

Enteral nutrition therapy is common practice in pediatric clinical settings. Often patients will receive a pump-assisted bolus feeding over 30 minutes several times per day using the same enteral feeding set (EFS). This study aims to determine the safest and most efficacious way to handle the EFS between feedings. Three EFS handling techniques were compared through simulation for bacterial growth, nursing time, and supply costs: (1) rinsing the EFS with sterile water after each feeding, (2) refrigerating the EFS between feedings, and (3) using a ready-to-hang (RTH) product maintained at room temperature. Cultures were obtained at baseline, hour 12, and hour 21 of the 24-hour cycle. A time-in-motion analysis was conducted and reported in average number of seconds to complete each procedure. Supply costs were inventoried for 1 month comparing the actual usage to our estimated usage. Of 1080 cultures obtained, the overall bacterial growth rate was 8.7%. The rinse and refrigeration techniques displayed similar bacterial growth (11.4% vs 10.3%, P = .63). The RTH technique displayed the least bacterial growth of any method (4.4%, P = .002). The time analysis in minutes showed the rinse method was the most time-consuming (44.8 ± 2.7) vs refrigeration (35.8 ± 2.6) and RTH (31.08 ± 0.6) ( P < .0001). All 3 EFS handling techniques displayed low bacterial growth. RTH was superior in bacterial growth, nursing time, and supply costs. Since not all pediatric formulas are available in RTH, we conclude that refrigerating the EFS between uses is the next most efficacious method for handling the EFS between bolus feeds.

Quality Rating and Improvement Systems and Children's Cognitive Development

ERIC Educational Resources Information Center

Jeon, Lieny; Buettner, Cynthia K.

2015-01-01

Background: Providing enriched learning environments is important to stimulating children's development in early childhood. Early child-care policymakers in many states in the US have adopted Quality Rating and Improvement Systems (QRIS) as a way to verify quality of child care and to support children's school readiness. Objective: The purpose of…

Validity of portfolio assessment: which qualities determine ratings?

PubMed

Driessen, Erik W; Overeem, Karlijn; van Tartwijk, Jan; van der Vleuten, Cees P M; Muijtjens, Arno M M

2006-09-01

The portfolio is becoming increasingly accepted as a valuable tool for learning and assessment. The validity of portfolio assessment, however, may suffer from bias due to irrelevant qualities, such as lay-out and writing style. We examined the possible effects of such qualities in a portfolio programme aimed at stimulating Year 1 medical students to reflect on their professional and personal development. In later curricular years, this portfolio is also used to judge clinical competence. We developed an instrument, the Portfolio Analysis Scoring Inventory, to examine the impact of form and content aspects on portfolio assessment. The Inventory consists of 15 items derived from interviews with experienced mentors, the literature, and the criteria for reflective competence used in the regular portfolio assessment procedure. Forty portfolios, selected from 231 portfolios for which ratings from the regular assessment procedure were available, were rated by 2 researchers, independently, using the Inventory. Regression analysis was used to estimate the correlation between the ratings from the regular assessment and those resulting from the Inventory items. Inter-rater agreement ranged from 0.46 to 0.87. The strongest predictor of the variance in the regular ratings was 'quality of reflection' (R 0.80; R2 66%). No further items accounted for a significant proportion of variance. Irrelevant items, such as writing style and lay-out, had negligible effects. The absence of an impact of irrelevant criteria appears to support the validity of the portfolio assessment procedure. Further studies should examine the portfolio's validity for the assessment of clinical competence.

Uncovering Predictors of Disagreement: Ensuring the Quality of Expert Ratings

ERIC Educational Resources Information Center

Hoth, Jessica; Schwarz, Björn; Kaiser, Gabriele; Busse, Andreas; König, Johannes; Blömeke, Sigrid

2016-01-01

Rating scales are a popular item format used in many types of assessments. Yet, defining which rating is correct often represents a challenge. Using expert ratings as benchmarks is one approach to ensuring the quality of a rating instrument. In this paper, such expert ratings are analyzed in detail taking a video-based test instrument of teachers'…

7 CFR 996.50 - Reconditioning failing quality peanuts.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Reconditioning failing quality peanuts. 996.50 Section... QUALITY AND HANDLING STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Quality and Handling Standards § 996.50 Reconditioning failing quality peanuts. (a) Lots of peanuts which have not been...

7 CFR 996.50 - Reconditioning failing quality peanuts.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Reconditioning failing quality peanuts. 996.50 Section... QUALITY AND HANDLING STANDARDS FOR DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Quality and Handling Standards § 996.50 Reconditioning failing quality peanuts. (a) Lots of peanuts which have not been...

Physiological and subjective measures of workload when shovelling with a conventional and two-handled ('levered') shovel.

PubMed

Bridger, R S; Cabion, N; Goedecke, J; Rickard, S; Schabort, E; Westgarth-Taylor, C; Lambert, M I

1997-11-01

Previous studies have suggested that the two-handled (levered) shovel is advantageous over the conventional spade from a biomechanical point of view. The aim of this experiment was to determine whether less energy was consumed while shovelling a load of sand with this shovel compared to a conventional tool. Accordingly, an experiment was designed in which subjects (n = 10) shovelled 1815 kg sand under laboratory conditions using either a conventional or a levered shovel. Heart rate and oxygen consumption were measured continuously during the trial and subjective data on perceived exertion, general fatigue and body discomfort were recorded after the trial. Although total energy expenditure was similar under both conditions (120 +/- 20 and 125 +/- 25 kcal; conventional versus two-handled spade), average heart rate was 4% higher when the two-handled shovel was used (p < 0.05). In addition, the mass of sand per scoop was 4% less with the two-handled shovel (p < 0.05). In conclusion, subjects used similar energy expenditure to shovel 1815 kg sand with the conventional shovel and the two-handled tool despite lower mass of sand per scoop with the latter. This can be explained by the fact that the increased mass of the additional handle compensated for the lower mass of sand per scoop. The higher average heart rate while shovelling with the two-handled shovel can be explained by the more erect posture.

Handling times and saturating transmission functions in a snail-worm symbiosis.

PubMed

Hopkins, Skylar R; McGregor, Cari M; Belden, Lisa K; Wojdak, Jeremy M

2018-06-16

All dynamic species interaction models contain an assumption that describes how contact rates scale with population density. Choosing an appropriate contact-density function is important, because different functions have different implications for population dynamics and stability. However, this choice can be challenging, because there are many possible functions, and most are phenomenological and thus difficult to relate to underlying ecological processes. Using one such phenomenological function, we described a nonlinear relationship between field transmission rates and host density in a common snail-oligochaete symbiosis. We then used a well-known contact function from predator-prey models, the Holling Type II functional response, to describe and predict host snail contact rates in the laboratory. The Holling Type II functional response accurately described both the nonlinear contact-density relationship and the average contact duration that we observed. Therefore, we suggest that contact rates saturate with host density in this system because each snail contact requires a non-instantaneous handling time, and additional possible contacts do not occur during that handling time. Handling times and nonlinear contact rates might also explain the nonlinear relationship between symbiont transmission and snail density that we observed in the field, which could be confirmed by future work that controls for other potential sources of seasonal variation in transmission rates. Because most animal contacts are not instantaneous, the Holling Type II functional response might be broadly relevant to diverse host-symbiont systems.

Ergonomics study on the handle length and lift angle for the culinary spatula.

PubMed

Wu, Swei-Pi; Hsieh, Chang-Sheng

2002-09-01

The culinary spatula (turning shovel) is one of the most common cooking tools used in the kitchen in Asia. However, the culinary spatula has seldom been ergonomically investigated. When a person uses a spatula to cook food, the operations involve repetitive bent-wrist motions, such as dorsiflexion, palmary flexion, and radial and ulnar deviations. These movements may cause cumulative trauma disorders in the upper extremities, and in particular carpal tunnel syndrome. A poorly designed culinary spatula will be ergonomically inefficient and cause injury to the hand and wrist. The purpose of this study was to investigate the effects of spatula handle length and lift angle on food-frying, food-turning, and food-shoveling performance. Eight female subjects were tested using 16 different culinary spatulas, with four different handle lengths (20, 25, 30 and 35 cm) and four different lift angles (15 degrees, 25 degrees, 35 degrees and 45 ). The criterion measures included cooking performance, and rating of perceived exertion. The subjects ranked their preference after all of the tasks in the tests were completed. The results showed that: (1) The handle length had a significant influence on the cooking performance, and rating of perceived exertion. The optimal handle lengths for frying food, turning food, and shoveling food were 20, 25 and 25 cm, respectively. (2) The lift angle significantly affected the cooking performance, and rating of perceived exertion. The optimal lift angles for frying food, turning food, and shoveling food were 15 degrees, 15 degrees and 25 degrees, respectively. (3) Both the handle length and lift angle had significant effects on subjective preference. For the handle length, the 20 cm length was the best. For the lift angle, the 25 angle was the best. (4) In general, a spatula with a 20 cm handle length and 25 degrees lift angle was the best. A spatula with a 25 cm handle length and 15 lift angle was the second most preferred. (5) However, to

Boar management and semen handling factors affect the quality of boar extended semen.

PubMed

Lopez Rodriguez, Alfonso; Van Soom, Ann; Arsenakis, Ioannis; Maes, Dominiek

2017-01-01

Artificial insemination (AI) is the preferred method for reproduction in the majority of the intensive pig production systems Worldwide. To this end, fresh extended ready-to-use semen doses are either purchased from AI-centres or produced by boars kept on-farm. For profitable semen production, it is necessary to obtain a maximum amount of high quality semen from each boar. This paper reviews current knowledge on factors that may affect semen quality by influencing the boar or the semen during processing. Genetic markers could be used for early detection of boars with the highest fertility potential. Genetic selection for fast growth might jeopardize semen quality. Early detection of boars no longer fit for semen production might be possible by ultrasonography of the testes. Seasonal variation in sperm quality could be associated with changes in photoperiod and heat stress during summer. Comfortable housing, with appropiate bedding material to avoid locomotion problems is essential. In some areas, cooling systems may be necessary to avoid heat stress. The sperm quality can be manipulated by feeding strategies aiming, for instance, to increase sperm resistance to oxidative stress and extend storage duration. High collection frequency will negatively influence sperm quality. Also, if collection is not hygienically performed it will result in bacterial contamination of the semen doses. The concern over bacterial contamination has risen not only because of its negative effect on semen quality but also due to the detection of antimicrobial resistance in isolates from extended semen. Moreover, bacterial and viral pathogens must be monitored because they affect semen production and quality and constitute a risk of herd infection. During processing, boar sperm are submitted to many stress factors that can cause oxidative stress and capacitation-like changes potentially reducing their fertility potential. Dilution rate or dilution temperature affects the quality of the semen

Hand sanitizer-dispensing door handles increase hand hygiene compliance: a pilot study.

PubMed

Babiarz, Lukasz S; Savoie, Brent; McGuire, Mark; McConnell, Lauren; Nagy, Paul

2014-04-01

Improving rates of hand hygiene compliance (HHC) has been shown to reduce nosocomial disease. We compared the HHC for a traditional wall-mounted unit and a novel sanitizer-dispensing door handle device in a hospital inpatient ultrasound area. HHC increased 24.5%-77.1% (P < .001) for the exam room with the sanitizer-dispensing door handle, whereas it remained unchanged for the other rooms. Technical improvements like a sanitizer-dispensing door handle can improve hospital HHC. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Recommendations for tool-handle material choice based on finite element analysis.

PubMed

Harih, Gregor; Dolšak, Bojan

2014-05-01

Huge areas of work are still done manually and require the usages of different powered and non-powered hand tools. In order to increase the user performance, satisfaction, and lower the risk of acute and cumulative trauma disorders, several researchers have investigated the sizes and shapes of tool-handles. However, only a few authors have investigated tool-handles' materials for further optimising them. Therefore, as presented in this paper, we have utilised a finite-element method for simulating human fingertip whilst grasping tool-handles. We modelled and simulated steel and ethylene propylene diene monomer (EPDM) rubber as homogeneous tool-handle materials and two composites consisting of EPDM rubber and EPDM foam, and also EPDM rubber and PU foam. The simulated finger force was set to obtain characteristic contact pressures of 20 kPa, 40 kPa, 80 kPa, and 100 kPa. Numerical tests have shown that EPDM rubber lowers the contact pressure just slightly. On the other hand, both composites showed significant reduction in contact pressure that could lower the risks of acute and cumulative trauma disorders which are pressure-dependent. Based on the results, it is also evident that a composite containing PU foam with a more evident and flat plateau deformed less at lower strain rates and deformed more when the plateau was reached, in comparison to the composite with EPDM foam. It was shown that hyper-elastic foam materials, which take into account the non-linear behaviour of fingertip soft tissue, can lower the contact pressure whilst maintaining low deformation rate of the tool-handle material for maintaining sufficient rate of stability of the hand tool in the hands. Lower contact pressure also lowers the risk of acute and cumulative trauma disorders, and increases comfort whilst maintaining performance. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Nursing home 5-star rating system exacerbates disparities in quality, by payer source.

PubMed

Konetzka, R Tamara; Grabowski, David C; Perraillon, Marcelo Coca; Werner, Rachel M

2015-05-01

Market-based reforms in health care, such as public reporting of quality, may inadvertently exacerbate disparities. We examined how the Centers for Medicare and Medicare Services' five-star rating system for nursing homes has affected residents who are dually enrolled in Medicare and Medicaid ("dual eligibles"), a particularly vulnerable and disadvantaged population. Specifically, we assessed the extent to which dual eligibles and non-dual eligibles avoided the lowest-rated nursing homes and chose the highest-rated homes once the five-star rating system began, in late 2008. We found that both populations resided in better-quality homes over time but that by 2010 the increased likelihood of choosing the highest-rated homes was substantially smaller for dual eligibles than for non-dual eligibles. Thus, the gap in quality, as measured by a nursing home's star rating, grew over time. Furthermore, we found that the benefit of the five-star system to dual eligibles was largely due to providers' improving their ratings, not to consumers' choosing different providers. We present evidence suggesting that supply constraints play a role in limiting dual eligibles' responses to quality ratings, since high-quality providers tend to be located close to relatively affluent areas. Increases in Medicaid payment rates for nursing home services may be the only long-term solution. Project HOPE—The People-to-People Health Foundation, Inc.

Investigation of a high speed data handling system for use with multispectral aircraft scanners

NASA Technical Reports Server (NTRS)

Kelly, W. L.; Meredith, B. D.

1978-01-01

A buffer memory data handling technique for use with multispectral aircraft scanners is presented which allows digital data generated at high data rates to be recorded on magnetic tape. A digital memory is used to temporarily store the data for subsequent recording at slower rates during the passive time of the scan line, thereby increasing the maximum data rate recording capability over real-time recording. Three possible implementations are described and the maximum data rate capability is defined in terms of the speed capability of the key hardware components. The maximum data rates can be used to define the maximum ground resolution achievable by a multispectral aircraft scanner using conventional data handling techniques.

Maternal handling during pregnancy reduces DMBA-induced mammary tumorigenesis among female offspring.

PubMed Central

Hilakivi-Clarke, L.

1997-01-01

The present study investigated whether handling of pregnant rats would affect mammary tumorigenesis in their female offspring. Pregnant Sprague-Dawley rats were injected daily with 0.05 ml of vehicle between days 14 and 20 of gestation or were left undisturbed. Handling did not have any effects on pregnancy or early development of the offspring. The female offspring were administered 10 mg of 7,12-dimethylbenz(a)anthracene (DMBA) at the age of 55 days. The rats whose mothers were handled during pregnancy had a significantly reduced mammary tumour incidence when compared with the offspring of non-handled mothers. Thus, on week 18 after DMBA exposure, 15% of the handled offspring had developed mammary tumours, whereas 44% of the non-handled offspring had tumours. No significant differences in the latency to tumour appearance, in the size of the tumours or in their growth rates were noted. Daily handling performed during post-natal days 5 and 20 produced similar data to that obtained for prenatal handling; on week 18 after DMBA exposure, the mammary tumour incidence among the post-natally handled rats was 22% and among the non-handled rats 44%. Possible deviations in hormonal parameters were also studied in adult female rats exposed in utero to handling. The onset of puberty tended to occur later among the handled offspring, but no differences in the uterine wet weights or serum oestradiol levels between the groups were noted. In conclusion, maternal handling reduced the offspring's risk to develop mammary tumours, and this effect was independent of the oestrogenic environment at adulthood. We propose that handling of a pregnant rat reduces mammary tumorigenesis in her offspring by means of changing the morphology of the mammary gland, the pattern of expression of specific genes and/or immune functions. PMID:9231913

Effects of Tone-Quality Changes on Intonation and Tone-Quality Ratings of High School and College Instrumentalists.

ERIC Educational Resources Information Center

Geringer, John M.; Worthy, Michael D.

1999-01-01

Investigates effects of variations in tone quality on listeners' perception of both tone quality and intonation. Indicates that more inexperienced instrumentalists rated stimuli that were "brighter" in quality as sharper in intonation, and those that were "darker" as flatter. Also, finds differences for brass versus woodwind instruments. (DSK)

Colorado Qualistar. QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Colorado's Qualistar prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family…

WASTE HANDLING BUILDING VENTILATION SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

P.A. Kumar

2000-06-21

The Waste Handling Building Ventilation System provides heating, ventilation, and air conditioning (HVAC) for the contaminated, potentially contaminated, and uncontaminated areas of the Monitored Geologic Repository's (MGR) Waste Handling Building (WHB). In the uncontaminated areas, the non-confinement area ventilation system maintains the proper environmental conditions for equipment operation and personnel comfort. In the contaminated and potentially contaminated areas, in addition to maintaining the proper environmental conditions for equipment operation and personnel comfort, the contamination confinement area ventilation system directs potentially contaminated air away from personnel in the WHB and confines the contamination within high-efficiency particulate air (HEPA) filtration units. Themore » contamination confinement areas ventilation system creates airflow paths and pressure zones to minimize the potential for spreading contamination within the building. The contamination confinement ventilation system also protects the environment and the public by limiting airborne releases of radioactive or other hazardous contaminants from the WHB. The Waste Handling Building Ventilation System is designed to perform its safety functions under accident conditions and other Design Basis Events (DBEs) (such as earthquakes, tornadoes, fires, and loss of the primary electric power). Additional system design features (such as compartmentalization with independent subsystems) limit the potential for cross-contamination within the WHB. The system provides status of important system parameters and equipment operation, and provides audible and/or visual indication of off-normal conditions and equipment failures. The Waste Handling Building Ventilation System confines the radioactive and hazardous material within the building such that the release rates comply with regulatory limits. The system design, operations, and maintenance activities incorporate ALARA (as low as is

District of Columbia Going for the Gold Tiered Rate Reimbursement System. QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of District of Columbia's Going for the Gold Tiered Rate Reimbursement Systemp repared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for…

CARRIER/CASK HANDLING SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

E.F. Loros

2000-06-23

The Carrier/Cask Handling System receives casks on railcars and legal-weight trucks (LWTs) (transporters) that transport loaded casks and empty overpacks to the Monitored Geologic Repository (MGR) from the Carrier/Cask Transport System. Casks that come to the MGR on heavy-haul trucks (HHTs) are transferred onto railcars before being brought into the Carrier/Cask Handling System. The system is the interfacing system between the railcars and LWTs and the Assembly Transfer System (ATS) and Canister Transfer System (CTS). The Carrier/Cask Handling System removes loaded casks from the cask transporters and transfers the casks to a transfer cart for either the ATS or CTS,more » as appropriate, based on cask contents. The Carrier/Cask Handling System receives the returned empty casks from the ATS and CTS and mounts the casks back onto the transporters for reshipment. If necessary, the Carrier/Cask Handling System can also mount loaded casks back onto the transporters and remove empty casks from the transporters. The Carrier/Cask Handling System receives overpacks from the ATS loaded with canisters that have been cut open and emptied and mounts the overpacks back onto the transporters for disposal. If necessary, the Carrier/Cask Handling System can also mount empty overpacks back onto the transporters and remove loaded overpacks from them. The Carrier/Cask Handling System is located within the Carrier Bay of the Waste Handling Building System. The system consists of cranes, hoists, manipulators, and supporting equipment. The Carrier/Cask Handling System is designed with the tooling and fixtures necessary for handling a variety of casks. The Carrier/Cask Handling System performance and reliability are sufficient to support the shipping and emplacement schedules for the MGR. The Carrier/Cask Handling System interfaces with the Carrier/Cask Transport System, ATS, and CTS as noted above. The Carrier/Cask Handling System interfaces with the Waste Handling Building System for

Quality Management, Certification and Rating of Health Information on the Net with MedCERTAIN: Using a medPICS/RDF/XML metadata structure for implementing eHealth ethics and creating trust globally

PubMed Central

Eysenbach, Gunther; Yihune, Gabriel; Lampe, Kristian; Cross, Phil; Brickley, Dan

2000-01-01

MedCERTAIN (MedPICS Certification and Rating of Trustworthy Health Information on the Net, http://www.medcertain.org/) is a recently launched international project funded under the European Union's (EU) "Action Plan for safer use of the Internet". It provides a technical infrastructure and a conceptual basis for an international system of "quality seals", ratings and self-labelling of Internet health information, with the final aim to establish a global "trustmark" for networked health information. Digital "quality seals" are evaluative metadata (using standards such as PICS=Platform for Internet Content Selection, now being replaced by RDF/XML) assigned by trusted third-party raters. The project also enables and encourages self-labelling with descriptive metainformation by web authors. Together these measures will help consumers as well as professionals to identify high-quality information on the Internet. MedCERTAIN establishes a fully functional demonstrator for a self- and third-party rating system enabling consumers and professionals to filter harmful health information and to positively identify and select high quality information. We aim to provide a trustmark system which allows citizens to place greater confidence in networked information, to encourage health information providers to follow best practices guidelines such as the Washington eHealth Code of Ethics, to provide effective feedback and law enforcement channels to handle user complaints, and to stimulate medical societies to develop standard for patient information. The project further proposes and identifies standards for interoperability of rating and description services (such as libraries or national health portals) and fosters a worldwide collaboration to guide consumers to high-quality information on the web.

The impact of involvement of biomedical scientists in specimen dissection and selection of blocks for histopathology: a study of time benefits and specimen handling quality in Ayrshire and Arran area laboratory

PubMed Central

Duthie, F R; Nairn, E R; Milne, A W; McTaggart, V; Topping, D

2004-01-01

Aims: To assess possible time benefits of specimen dissection by biomedical scientists (BMSs) and the quality of specimen handling by BMSs, in a department where BMSs trim those specimens requiring simple descriptions, from which standard blocks are taken. Methods: Specimen handling by BMSs and consultant pathologists was compared. Time taken for each specimen trimmed was recorded prospectively. To determine specimen handling quality, adherence to dissection standard operating procedures (SOPs) was assessed by recording retrospectively whether or not each action in the SOP had been performed. Information on subsequently required extra levels or blocks was recorded. Results: Analysis of data from 672 specimens trimmed by consultants showed that any given action in the SOPs was performed on average on 60.2% of applicable/assessable specimens; for 660 similar specimens trimmed by BMSs, each action was performed on average on 80.1% of specimens. Of the specimens where data on extra blocks were recorded, extra blocks were required in 3% of those trimmed by pathologists and in 4% of those trimmed by BMSs. Extra levels were required in 12% of those trimmed by pathologists and in 16% of those trimmed by BMSs. BMS trimming saves 16 hours of consultant time each month. The difference between pathologists and BMSs in time for each specimen trimmed is negligible. Conclusions: The advantages of increased adherence to trimming SOPs and saving consultant time outweigh the relatively small number of extra blocks and levels required when BMSs trim. There is no reduction in quality of dissection. PMID:14693831

Alumina Handling Dustiness

NASA Astrophysics Data System (ADS)

Authier-Martin, Monique

Dustiness of calcined alumina is a major concern, causing undesirable working conditions and serious alumina losses. These losses occur primarily during unloading and handling or pot loading and crust breaking. The handling side of the problem is first addressed. The Perra pulvimeter constitutes a simple and reproducible tool to quantify handling dustiness and yields results in agreement with plant experience. Attempts are made to correlate dustiness with bulk properties (particle size, attrition index, …) for a large number of diverse aluminas. The characterization of the dust generated with the Perra pulvimeter is most revealing. The effect of the addition of E.S.P. dust is also reported.

Handling of Polyvinylsiloxane Versus Polyether for Implant Impressions.

PubMed

Farhan, Daniel; Lauer, Wiebke; Heydecke, Guido; Aarabi, Ghazal; Reissmann, Daniel R

2016-01-01

This study compared polyvinylsiloxane with polyether in handling dental impressions. Each participant (N = 39) made four impressions, each a combination of pickup and reseating techniques with polyether or polyvinylsiloxane, of one implant cast representing a specific clinical situation (tooth gaps, limited residual dentition, or edentulous jaw). Handling of impressions was subsequently rated by using a 12-item questionnaire with 100-mm visual analog scales. While mean satisfaction scores were higher for polyvinylsiloxane than for polyether (69.5/63.0, P < .001), differences among subgroups were statistically significant only for pickup technique, limited residual dentition, and edentulous jaw. Implant impressions made with polyvinylsiloxane using a pickup technique seem to be the best option for most clinical situations.

Influence of temperament score and handling facility on stress, reproductive hormone concentrations, and fixed time AI pregnancy rates in beef heifers.

PubMed

Kasimanickam, R; Schroeder, S; Assay, M; Kasimanickam, V; Moore, D A; Gay, J M; Whittier, W D

2014-10-01

The objectives were (i) to evaluate the effect of temperament, determined by modified 2-point chute exit and gait score, on artificial insemination (AI) pregnancy rates in beef heifers following fixed time AI and (ii) to determine the effect of temperament on cortisol, substance-P, prolactin and progesterone at initiation of synchronization and at the time of AI. Angus beef heifers (n = 967) at eight locations were included in this study. At the initiation of synchronization (Day 0 = initiation of synchronization), all heifers received a body condition score (BCS), and temperament score (0 = calm; slow exit and walk or 1 = excitable; fast exit or jump or trot or run). Blood samples were collected from a sub-population of heifers (n = 86) at both synchronization initiation and the time of AI to determine the differences in serum progesterone, cortisol, prolactin and substance-P concentrations between temperament groups. Heifers were synchronized with 5-day CO-Synch+ controlled internal drug release (CIDR) protocol and were inseminated at 56 h after CIDR removal. Heifers were examined for pregnancy by ultrasound 70 days after AI to determine AI pregnancy. Controlling for synchronization treatment (p = 0.03), facility design (p = 0.05), and cattle handling facility design by temperament score interaction (p = 0.02), the AI pregnancy differed between heifers with excitable and calm temperament (51.9% vs 60.3%; p = 0.01). The alley-way with acute bends and turns, and long straight alley-way had lower AI pregnancy rate than did the semicircular alley-way (53.5%, 56.3% and 67.0% respectively; p = 0.05). The serum hormone concentrations differed significantly between different types of cattle handling facility (p < 0.05). The cattle handling facility design by temperament group interactions significantly influenced progesterone (p = 0.01), cortisol (p = 0.01), prolactin (p = 0.02) and substance-P (p = 0.04) both at the initiation of

Ergonomic material-handling device

DOEpatents

Barsnick, Lance E.; Zalk, David M.; Perry, Catherine M.; Biggs, Terry; Tageson, Robert E.

2004-08-24

A hand-held ergonomic material-handling device capable of moving heavy objects, such as large waste containers and other large objects requiring mechanical assistance. The ergonomic material-handling device can be used with neutral postures of the back, shoulders, wrists and knees, thereby reducing potential injury to the user. The device involves two key features: 1) gives the user the ability to adjust the height of the handles of the device to ergonomically fit the needs of the user's back, wrists and shoulders; and 2) has a rounded handlebar shape, as well as the size and configuration of the handles which keep the user's wrists in a neutral posture during manipulation of the device.

Application of psychometric theory to the measurement of voice quality using rating scales.

PubMed

Shrivastav, Rahul; Sapienza, Christine M; Nandur, Vuday

2005-04-01

Rating scales are commonly used to study voice quality. However, recent research has demonstrated that perceptual measures of voice quality obtained using rating scales suffer from poor interjudge agreement and reliability, especially in the mid-range of the scale. These findings, along with those obtained using multidimensional scaling (MDS), have been interpreted to show that listeners perceive voice quality in an idiosyncratic manner. Based on psychometric theory, the present research explored an alternative explanation for the poor interlistener agreement observed in previous research. This approach suggests that poor agreement between listeners may result, in part, from measurement errors related to a variety of factors rather than true differences in the perception of voice quality. In this study, 10 listeners rated breathiness for 27 vowel stimuli using a 5-point rating scale. Each stimulus was presented to the listeners 10 times in random order. Interlistener agreement and reliability were calculated from these ratings. Agreement and reliability were observed to improve when multiple ratings of each stimulus from each listener were averaged and when standardized scores were used instead of absolute ratings. The probability of exact agreement was found to be approximately .9 when using averaged ratings and standardized scores. In contrast, the probability of exact agreement was only .4 when a single rating from each listener was used to measure agreement. These findings support the hypothesis that poor agreement reported in past research partly arises from errors in measurement rather than individual differences in the perception of voice quality.

High angle of attack flying qualities criteria for longitudinal rate command systems

NASA Technical Reports Server (NTRS)

Wilson, David J.; Citurs, Kevin D.; Davidson, John B.

1994-01-01

This study was designed to investigate flying qualities requirements of alternate pitch command systems for fighter aircraft at high angle of attack. Flying qualities design guidelines have already been developed for angle of attack command systems at 30, 45, and 60 degrees angle of attack, so this research fills a similar need for rate command systems. Flying qualities tasks that require post-stall maneuvering were tested during piloted simulations in the McDonnell Douglas Aerospace Manned Air Combat Simulation facility. A generic fighter aircraft model was used to test angle of attack rate and pitch rate command systems for longitudinal gross acquisition and tracking tasks at high angle of attack. A wide range of longitudinal dynamic variations were tested at 30, 45, and 60 degrees angle of attack. Pilot comments, Cooper-Harper ratings, and pilot induced oscillation ratings were taken from five pilots from NASA, USN, CAF, and McDonnell Douglas Aerospace. This data was used to form longitudinal design guidelines for rate command systems at high angle of attack. These criteria provide control law design guidance for fighter aircraft at high angle of attack, low speed flight conditions. Additional time history analyses were conducted using the longitudinal gross acquisition data to look at potential agility measures of merit and correlate agility usage to flying qualities boundaries. This paper presents an overview of this research.

Moving up the Ladder: How Do States Deliver Quality Improvement Supports within Their Quality Rating and Improvement Systems? Brief

ERIC Educational Resources Information Center

Holod, Aleksandra; Faria, Ann-Marie; Weinberg, Emily; Howard, Eboni

2015-01-01

As national attention has increasingly focused on the potential for high-quality early childhood education (ECE) to improve children's school readiness, states have developed quality rating and improvement systems (QRISs) to document the quality of ECE programs, support systematic quality improvement, and provide clear information to families…

Quality rating and private-prices: Evidence from the nursing home industry.

PubMed

Huang, Sean Shenghsiu; Hirth, Richard A

2016-12-01

We use the rollout of the five-star rating of nursing homes to study how private-pay prices respond to quality rating. We find that star rating increases the price differential between top- and bottom-ranked facilities. On average, prices of top-ranked facilities increased by 4.8 to 6.0 percent more than the prices of bottom-ranked facilities. We find stronger price effects in markets that are less concentrated where consumers may have more choices of alternative nursing homes. Our results suggest that with simplified design and when markets are less concentrated, consumers are more responsive to quality reporting. Copyright © 2016 Elsevier B.V. All rights reserved.

Skills in Handling Turbuhaler, Diskus, and Pressurized Metered-Dose Inhaler in Korean Asthmatic Patients

PubMed Central

Lee, Sang Min; Chang, Yoon-Seok; Kim, Cheol-Woo; Kim, Tae-Bum; Kim, Sang-Heon; Kwon, Yong-Eun; Lee, Jong-Myung; Lee, Soo-Keol; Jeong, Jae-Won; Park, Jung-Won; Cho, Sang-Heon; Moon, Hee-Bom

2011-01-01

Purpose The objective of this study was to evaluate skills in handling inhalers and factors associated with these skills among patients with asthma who had undergone treatment at special asthma and allergy clinics in Korea. Methods We enrolled 78 subjects who used Turbuhaler and 145 who used Diskus for asthma control at special clinics in 10 university hospitals and visually assessed their skills in handling these inhalers. We also evaluated skills in 137 subjects who had used pressurized metered-dose inhalers (pMDIs) for symptom relief. Age, sex, duration of asthma and inhaler use, smoking status, monthly income, highest grade completed in school and previous instruction for handling inhalers were also measured to evaluate their association with overall inhaler skills. Results Performance grade was inadequate for 12.8% of participants using Turbuhaler, 6.2% for Diskus, and 23.4% for pMDIs. The success rates for each step in handling the inhalers were relatively high except for the "exhale slowly to residual volume" step, in which success rates ranged from 24.2% to 28.5%. Older age, male sex, lower educational grade, and absence of previous instruction for handling inhalers were associated with inadequate inhaler technique in univariate analysis; however, only older age and absence of previous instruction remained significant independent risk factors in multivariate analysis. Conclusions Among Korean asthmatic patients in special asthma and allergy clinics, skills in handling their inhalers were mostly excellent; meanwhile, older age and absence of previous instruction for handling inhalers were associated with inadequate techniques. PMID:21217925

Rating educational quality: factors in the erosion of professional standards.

PubMed

Albanese, M

1999-06-01

Changes in the health care environment are putting increasing pressure on medical schools to make faculty accountable and to document the quality of the medical education they provide. Faculty's ratings of students' performances and students' ratings of faculty's teaching are important elements in these efforts to document educational quality. This article discusses selected research related to factors affecting raters' judgments, analyzes how changes in the health care environment are influencing such judgments, and links these influences to the system that upholds professional standards. Ratings are known to have a positive bias (generosity error), provide limited discrimination, and often fail to document serious deficits. The potential sources of these problems relate to the mechanics of the rating task, the system used to obtain ratings, and factors affecting rater judgment. As managed care demands reduce the time faculty have for teaching, as system-wide disincentives to provide negative ratings proliferate, and as social engineering challenges, such as the Americans with Disabilities Act, impose differential standards for students, the natural tendency to avoid giving negative ratings becomes even harder to resist. Ultimately, these forces compromise the capability of faculty to uphold the standards of the profession. The author calls for a national effort to stem the erosion of those standards.

Can better infrastructure and quality reduce hospital infant mortality rates in Mexico?

PubMed

Aguilera, Nelly; Marrufo, Grecia M

2007-02-01

Preliminary evidence from hospital discharges hints enormous disparities in infant hospital mortality rates. At the same time, public health agencies acknowledge severe deficiencies and variations in the quality of medical services across public hospitals. Despite these concerns, there is limited evidence of the contribution of hospital infrastructure and quality in explaining variations in outcomes among those who have access to medical services provided at public hospitals. This paper provides evidence to address this question. We use probabilistic econometric methods to estimate the impact of material and human resources and hospital quality on the probability that an infant dies controlling for socioeconomic, maternal and reproductive risk factors. As a measure of quality, we calculate for the first time for Mexico patient safety indicators developed by the AHRQ. We find that the probability to die is affected by hospital infrastructure and by quality. In this last regard, having been treated in a hospital with the worse quality incidence doubles the probability to die. This paper also presents evidence on the contribution of other risk factors on perinatal mortality rates. The conclusions of this paper suggest that lower infant mortality rates can be reached by implementing a set of coherent public policy actions including an increase and reorganization of hospital infrastructure, quality improvement, and increasing demand for health by poor families.

Students' Strategies for Exception Handling

ERIC Educational Resources Information Center

Rashkovits, Rami; Lavy, Ilana

2011-01-01

This study discusses and presents various strategies employed by novice programmers concerning exception handling. The main contributions of this paper are as follows: we provide an analysis tool to measure the level of assimilation of exception handling mechanism; we present and analyse strategies to handle exceptions; we present and analyse…

Application of Psychometric Theory to the Measurement of Voice Quality Using Rating Scales

ERIC Educational Resources Information Center

Shrivastav, Rahul; Sapienza, Christine M.; Nandur, Vuday

2005-01-01

Rating scales are commonly used to study voice quality. However, recent research has demonstrated that perceptual measures of voice quality obtained using rating scales suffer from poor interjudge agreement and reliability, especially in the midrange of the scale. These findings, along with those obtained using multidimensional scaling (MDS), have…

Pennsylvania Keystone STARS: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Pennsylvania's Keystone STARS prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

Study on Handing Process and Quality Degradation of Oil Palm Fresh Fruit Bunches (FFB)

NASA Astrophysics Data System (ADS)

Mat Sharif, Zainon Binti; Taib, Norhasnina Binti Mohd; Yusof, Mohd Sallehuddin Bin; Rahim, Mohammad Zulafif Bin; Tobi, Abdul Latif Bin Mohd; Othman, Mohd Syafiq Bin

2017-05-01

The main objective of this study is to determine the relationship between quality of oil palm fresh fruit bunches (FFB) and handling processes. The study employs exploratory and descriptive design, with quantitative approach and purposive sampling using self-administrated questionnaires, were obtained from 30 smallholder respondents from the Southern Region, Peninsular Malaysia. The study reveals that there was a convincing relationship between quality of oil palm fresh fruit bunches (FFB) and handling processes. The main handling process factors influencing quality of oil palm fresh fruit bunches (FFB) were harvesting activity and handling at the plantation area. As a result, it can be deduced that the handling process factors variable explains 82.80% of the variance that reflects the quality of oil palm fresh fruit bunches (FFB). The overall findings reveal that the handling process factors do play a significant role in the quality of oil palm fresh fruit bunches (FFB).

Minnesota Parent Aware: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Minnesota's Parent Aware prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for Family…

46 CFR 111.106-13 - Cargo handling devices or cargo pump rooms handling flammable or combustible cargoes.

Code of Federal Regulations, 2014 CFR

2014-10-01

... pierced by fixed lights, drive shafts, and pump-engine control rods, provided that the shafts and rods are... 46 Shipping 4 2014-10-01 2014-10-01 false Cargo handling devices or cargo pump rooms handling... OSVs § 111.106-13 Cargo handling devices or cargo pump rooms handling flammable or combustible cargoes...

Nonlinear frequency compression: effects on sound quality ratings of speech and music.

PubMed

Parsa, Vijay; Scollie, Susan; Glista, Danielle; Seelisch, Andreas

2013-03-01

Frequency lowering technologies offer an alternative amplification solution for severe to profound high frequency hearing losses. While frequency lowering technologies may improve audibility of high frequency sounds, the very nature of this processing can affect the perceived sound quality. This article reports the results from two studies that investigated the impact of a nonlinear frequency compression (NFC) algorithm on perceived sound quality. In the first study, the cutoff frequency and compression ratio parameters of the NFC algorithm were varied, and their effect on the speech quality was measured subjectively with 12 normal hearing adults, 12 normal hearing children, 13 hearing impaired adults, and 9 hearing impaired children. In the second study, 12 normal hearing and 8 hearing impaired adult listeners rated the quality of speech in quiet, speech in noise, and music after processing with a different set of NFC parameters. Results showed that the cutoff frequency parameter had more impact on sound quality ratings than the compression ratio, and that the hearing impaired adults were more tolerant to increased frequency compression than normal hearing adults. No statistically significant differences were found in the sound quality ratings of speech-in-noise and music stimuli processed through various NFC settings by hearing impaired listeners. These findings suggest that there may be an acceptable range of NFC settings for hearing impaired individuals where sound quality is not adversely affected. These results may assist an Audiologist in clinical NFC hearing aid fittings for achieving a balance between high frequency audibility and sound quality.

Mammography Clinical Image Quality and the False Positive Rate in a Canadian Breast Cancer Screening Program.

PubMed

Guertin, Marie-Hélène; Théberge, Isabelle; Zomahoun, Hervé Tchala Vignon; Dufresne, Michel-Pierre; Pelletier, Éric; Brisson, Jacques

2018-05-01

The study sought to determine if mammography quality is associated with the false positive (FP) rate in the Quebec breast cancer screening program in 2004 and 2005. Mammography quality of a random sample of screen-film mammograms was evaluated by an expert radiologist following the criteria of the Canadian Association of Radiologists. For each screening examination, scores ranging from 1 (poor quality) to 5 (excellent quality) were attributed for positioning, compression, contrast, exposure level, sharpness, and artifacts. A final overall quality score (lower or higher) was also given. Poisson regression models with robust estimation of variance and adjusted for potential confounding factors were used to assess associations of mammography quality with the FP rate. Among 1,209 women without cancer, there were 104 (8.6%) FPs. Lower overall mammography quality is associated with an increase in the FP rate (risk ratio [RR], 1.4; 95% confidence interval [CI], 1.0-2.1; P = .07) but this increase was not statistically significant. Artifacts were associated with an increase in the FP rate (RR, 2.1; 95% CI, 1.3-3.3; P = .01) whereas lower quality of exposure level was related to a reduction of the FP rate (RR, 0.4; 95% CI, 0.1-1.0; P = .01). Lower quality scores for all other quality attributes were related to a nonstatistically significant increase in the FP rate of 10%-30%. Artifacts can have a substantial effect on the FP rate. The effect of overall mammography quality on the FP rate may also be substantial and needs to be clarified. Copyright © 2017 Canadian Association of Radiologists. Published by Elsevier Inc. All rights reserved.

Development and validation of a Chinese music quality rating test.

PubMed

Cai, Yuexin; Zhao, Fei; Zheng, Yiqing

2013-09-01

The present study aims to develop and validate a Chinese music quality rating test (MQRT). In Experiment 1, 22 music pieces were initially selected and paired as a 'familiar music piece' and 'unfamiliar music piece' based on familiarities amongst the general public in the categories of classical music (6), Chinese folk music (8), and pop music (8). Following the selection criteria, one pair of music pieces from each music category was selected and used for the MQRT in Experiment 2. In Experiment 2, the MQRT was validated using these music pieces in the categories 'Pleasantness', 'Naturalness', 'Fullness', 'Roughness', and 'Sharpness'. Seventy-two adult participants and 30 normal-hearing listeners were recruited in Experiments 1 and 2, respectively. Significant differences between the familiar and unfamiliar music pieces were found in respect of pleasantness rating for folk and pop music pieces as well as in sharpness rating for pop music pieces. The comparison of music category effect on MQRT found significant differences in pleasantness, fullness, and sharpness ratings. The Chinese MQRT developed in the present study is an effective tool for assessing music quality.

Handling of drug-related emergencies: an evaluation of emergency medical dispatch.

PubMed

Tonje, Lorem; Elisabeth, Saether; Lars, Wik

2009-02-01

Documenting the quality of emergency dispatch centres handling of emergency calls regarding intoxicated unconscious patients. Interview with eight emergency dispatch centre directors and a nationwide survey among 313 dispatchers in Norway were performed. In addition, a customized scoring system was used to evaluate dispatcher log recordings of real cases. The recordings were compared with information from corresponding ambulance records. Ninety-nine percent of the dispatchers stated that they used the Norwegian protocol for medical emergencies and 89% of them found it useful. The interviews, the survey, and the recordings, however, documented frequent deviation from the protocol. This instructs ambulance dispatch for any unconscious patient, but 21% stated that they would not dispatch any resource for an unconscious patient without further survey in alcohol-related cases. This was significantly more often (P<0.05) than for the narcotic, combination and prescription - drug-related cases with 4, 10 and 7%, respectively. The recordings revealed deviation from the protocol with dispatchers only determining the patients' level of consciousness and respiratory status in 64 and 70% of the cases, respectively. For 16% of the cases, the dispatcher did not ask the caller about consciousness at all, even though these patients later were found with reduced consciousness. On the basis of the interviews and the survey, cases were handled according to guidelines. The log recordings, however, disclosed deviation from the protocol. Alcohol intoxication was associated with higher rate of deviation from the protocol compared with other intoxications.

Content, Quality, and Assessment Tools of Physician-Rating Websites in 12 Countries: Quantitative Analysis.

PubMed

Rothenfluh, Fabia; Schulz, Peter J

2018-06-14

Websites on which users can rate their physician are becoming increasingly popular, but little is known about the website quality, the information content, and the tools they offer users to assess physicians. This study assesses these aspects on physician-rating websites in German- and English-speaking countries. The objective of this study was to collect information on websites with a physician rating or review tool in 12 countries in terms of metadata, website quality (transparency, privacy and freedom of speech of physicians and patients, check mechanisms for appropriateness and accuracy of reviews, and ease of page navigation), professional information about the physician, rating scales and tools, as well as traffic rank. A systematic Web search based on a set of predefined keywords was conducted on Google, Bing, and Yahoo in August 2016. A final sample of 143 physician-rating websites was analyzed and coded for metadata, quality, information content, and the physician-rating tools. The majority of websites were registered in the United States (40/143) or Germany (25/143). The vast majority were commercially owned (120/143, 83.9%), and 69.9% (100/143) displayed some form of physician advertisement. Overall, information content (mean 9.95/25) as well as quality were low (mean 18.67/47). Websites registered in the United Kingdom obtained the highest quality scores (mean 26.50/47), followed by Australian websites (mean 21.50/47). In terms of rating tools, physician-rating websites were most frequently asking users to score overall performance, punctuality, or wait time in practice. This study evidences that websites that provide physician rating should improve and communicate their quality standards, especially in terms of physician and user protection, as well as transparency. In addition, given that quality standards on physician-rating websites are low overall, the development of transparent guidelines is required. Furthermore, attention should be paid to the

Estimating respiratory rate from FBG optical sensors by using signal quality measurement.

PubMed

Yongwei Zhu; Maniyeri, Jayachandran; Fook, Victor Foo Siang; Haihong Zhang

2015-08-01

Non-intrusiveness is one of the advantages of in-bed optical sensor device for monitoring vital signs, including heart rate and respiratory rate. Estimating respiratory rate reliably using such sensors, however, is challenging, due to body movement, signal variation according to different subjects or body positions, etc. This paper presents a method for reliable respiratory rate estimation for FBG optical sensors by introducing signal quality estimation. The method estimates the quality of the signal waveform by detecting regularly repetitive patterns using proposed spectrum and cepstrum analysis. Multiple window sizes are used to cater for a wide range of target respiratory rates. Furthermore, the readings of multiple sensors are fused to derive a final respiratory rate. Experiments with 12 subjects and 2 body positions were conducted using polysomnography belt signal as groundtruth. The results demonstrated the effectiveness of the method.

Parental Perceptions of Child Care Quality in Centre-Based and Home-Based Settings: Associations with External Quality Ratings

ERIC Educational Resources Information Center

Lehrer, Joanne S.; Lemay, Lise; Bigras, Nathalie

2015-01-01

The current study examined how parental perceptions of child care quality were related to external quality ratings and considered how parental perceptions of quality varied according to child care context (home-based or centre-based settings). Parents of 179 4-year-old children who attended child care centres (n = 141) and home-based settings…

Primary care practice and facility quality orientation: influence on breast and cervical cancer screening rates.

PubMed

Goldzweig, Caroline Lubick; Parkerton, Patricia H; Washington, Donna L; Lanto, Andrew B; Yano, Elizabeth M

2004-04-01

Despite the importance of early cancer detection, variation in screening rates among physicians is high. Insights into factors influencing variation can guide efforts to decrease variation and increase screening rates. To explore the association of primary care practice features and a facility's quality orientation with breast and cervical cancer screening rates. Cross-sectional study of screening rates among 144 Department of Veterans Affairs (VA) medical centers and for a national sample of women. We linked practice structure and quality improvement characteristics of individual VA medical centers from 2 national surveys (1 to primary care directors and 1 to a stratified random sample of employees) to breast and cervical cancer screening rates determined from a review of random medical records. We conducted bivariate analyses and multivariate logistic regression of primary care practice and facility features on cancer screening rates, above and below the median. While the national screening rates were high for breast (87%) and cervical cancer (90%), higher screening rates were more likely when primary care providers were consistently notified of specialty visits and when staff perceived a greater organizational commitment to quality and anticipated rewards and recognition for better performance. Organization and quality orientation of the primary care practice and its facility can enhance breast and cervical cancer screening rates. Internal recognition of quality performance and an overall commitment to quality improvement may foster improved prevention performance, with impact varying by clinical service.

Effects of a preceptorship programme on turnover rate, cost, quality and professional development.

PubMed

Lee, Tso-Ying; Tzeng, Wen-Chii; Lin, Chia-Huei; Yeh, Mei-Ling

2009-04-01

The purpose of the present study was to design a preceptorship programme and to evaluate its effects on turnover rate, turnover cost, quality of care and professional development. A high turnover rate of nurses is a common global problem. How to improve nurses' willingness to stay in their jobs and reduce the high turnover rate has become a focus. Well-designed preceptorship programmes could possibly decrease turnover rates and improve professional development. A quasi-experimental research design was used. First, a preceptorship programme was designed to establish the role and responsibilities of preceptors in instructing new nurses. Second, a quasi-experimental design was used to evaluate the preceptorship programme. Data on new nurses' turnover rate, turnover cost, quality of nursing care, satisfaction of preceptor's teaching and preceptor's perception were measured. After conducting the preceptorship programme, the turnover rate was 46.5% less than the previous year. The turnover cost was decreased by US$186,102. Additionally, medication error rates made by new nurses dropped from 50-0% and incident rates of adverse events and falls decreased. All new nurses were satisfied with preceptor guidance. The preceptorship programme effectively lowered the turnover rate of new nurses, reduced turnover costs and enhanced the quality of nursing care, especially by reducing medication error incidents. Positive feedback about the programme was received from new nurses. Study findings may offer healthcare administrators another option for retaining new nurses, controlling costs, improving quality and fostering professional development. In addition, incentives and effective support from the organisation must be considered when preceptors perform preceptorship responsibilities.

Promoting Access to Quality Child Care: Critical Steps in Conducting Market Rate Surveys and Establishing Rate Policies.

ERIC Educational Resources Information Center

Stoney, Louise

This report is designed to help policymakers, child care providers, and advocates establish child care rate support policies that support high quality in the context of government-subsidized, privately-provided child care. It also provides advice on the development and interpretation of market rate surveys of local child care fees. Part 1…

The association of Nursing Home Compare quality measures with market competition and occupancy rates.

PubMed

Castle, Nicholas G; Liu, Darren; Engberg, John

2008-01-01

Since 2002, the Centers for Medicare and Medicaid Services have reported quality measures on the Nursing Home Compare Web site. It has been assumed that nursing homes are able to make improvements on these measures. In this study researchers examined nursing homes to see whether they have improved their quality scores, after accounting for regression to the mean. Researchers also examined whether gains varied according to market competition or market occupancy rates. They identified some regression to the mean for the quality measure scores over time; nevertheless, they also determined that some nursing homes had indeed made small improvements in their quality measure scores. As would be predicted based on the market-driven mechanism underlying quality improvements using report cards, the greatest improvements occurred in the most competitive markets and in those with the Lowest average occupancy rates. As policies to promote more competition in Long-term care proceed, further reducing occupancy rates, further, albeit small, quality gains will likely be made in the future.

Ergonomics and patient handling.

PubMed

McCoskey, Kelsey L

2007-11-01

This study aimed to describe patient-handling demands in inpatient units during a 24-hour period at a military health care facility. A 1-day total population survey described the diverse nature and impact of patient-handling tasks relative to a variety of nursing care units, patient characteristics, and transfer equipment. Productivity baselines were established based on patient dependency, physical exertion, type of transfer, and time spent performing the transfer. Descriptions of the physiological effect of transfers on staff based on patient, transfer, and staff characteristics were developed. Nursing staff response to surveys demonstrated how patient-handling demands are impacted by the staff's physical exertion and level of patient dependency. The findings of this study describe the types of transfers occurring in these inpatient units and the physical exertion and time requirements for these transfers. This description may guide selection of the most appropriate and cost-effective patient-handling equipment required for specific units and patients.

Seed handling practices for southern pines grown in containers

Treesearch

William H. Pawuk; James P. Barnett

1979-01-01

Cost of producing container-grown seedlings increase when containers are not fully stocked. Best use of containers requires high seed viability and low losses of newly germinated seedlings. Seed handling practices before and after sowing affect germination and seedling survival. This is a summary of seed preperation, sowing rates, disease control, and seed...

Conditioning laboratory cats to handling and transport.

PubMed

Gruen, Margaret E; Thomson, Andrea E; Clary, Gillian P; Hamilton, Alexandra K; Hudson, Lola C; Meeker, Rick B; Sherman, Barbara L

2013-10-01

As research subjects, cats have contributed substantially to our understanding of biological systems, from the development of mammalian visual pathways to the pathophysiology of feline immunodeficiency virus as a model for human immunodeficiency virus. Few studies have evaluated humane methods for managing cats in laboratory animal facilities, however, in order to reduce fear responses and improve their welfare. The authors describe a behavioral protocol used in their laboratory to condition cats to handling and transport. Such behavioral conditioning benefits the welfare of the cats, the safety of animal technicians and the quality of feline research data.

Alternative Pathways in Family Child Care Quality Rating and Improvement Systems

ERIC Educational Resources Information Center

Kelton, Robyn E.; Talan, Teri N.; Bloom, Paula J.

2013-01-01

As research continues to underscore the positive impact high-quality early childhood programs have on young children, numerous states have implemented quality rating and improvement systems (QRIS) to measure and improve the services young children receive across a wide range of early learning settings. These state systems range from two to five…

Transfusion rate as a quality metric: is blood conservation a learnable skill?

PubMed

Paone, Gaetano; Brewer, Robert; Likosky, Donald S; Theurer, Patricia F; Bell, Gail F; Cogan, Chad M; Prager, Richard L

2013-10-01

Between January 2008 and December 2012, a multicenter quality collaborative initiated a focus on blood conservation as a quality metric, with educational presentations and quarterly reporting of institutional-level perioperative transfusion rates and outcomes. This prospective cohort study was undertaken to determine the effect of that initiative on transfusion rates after isolated coronary artery bypass grafting (CABG). Between January 1, 2008, and December 31, 2012, 30,271 patients underwent isolated CABG in Michigan. Evaluated were annual crude and adjusted trends in overall transfusion rates for red blood cells (RBCs), fresh frozen plasma (FFP), and platelets, and in operative death. Transfusion rates continuously decreased for all blood products. RBC use decreased from 56.4% in 2008 (baseline) to 38.3% in 2012, FFP use decreased from 14.8% to 9.1%, and platelet use decreased from 20.5% to 13.4% (ptrend < 0.001 for all). A significant reduction occurred in deep sternal wound infection, reoperation for bleeding, renal failure, prolonged ventilation, initial ventilator time, and intensive care unit duration. The percentage of patients discharged home significantly increased (ptrend < 0.001). Mortality rates did not differ significantly (ptrend = 0.11). In a multicenter quality collaborative, increased attention to transfusion-related outcomes and blood conservation techniques, coincident with regular reporting and review of perioperative transfusion rates as a quality metric, was associated with a significant decrease in blood product utilization. These reductions were concurrent with significant improvement in most perioperative outcomes. This intervention was also safe, as it was not associated with any increases in mortality. Copyright © 2013 The Society of Thoracic Surgeons. Published by Elsevier Inc. All rights reserved.

Handling of boar spermatozoa during and after flow cytometric sex-sorting process to improve their in vitro fertilizing ability.

PubMed

del Olmo, D; Parrilla, I; Gil, M A; Maside, C; Tarantini, T; Angel, M A; Roca, J; Martinez, E A; Vazquez, J M

2013-09-01

The objective of this study was to develop an adequate sperm handling protocol in order to obtain a sex-sorted sperm population with an optimal fertilizing ability. For this purpose, different aspects of the sorting procedure were examined. The effects of the high dilution rates (experiment 1), type of collection medium used (experiment 2), and sheath fluid composition (experiment 3) on sorted boar sperm quality and function were evaluated. Sperm quality was assessed by motility and viability tests, whereas sperm function was evaluated by an in vitro fertilization assay which determined the penetration and polyspermy rates as well as the mean number of sperm penetrating each oocyte. In experiment 1, the results obtained indicated that the high dilution rates did not cause a decrease either in the sperm quality parameters evaluated or the in vitro fertilization ability of spermatozoa. In experiment 2, although sperm quality was not affected, fertilizing ability was compromised after sorting, regardless of the collection medium that was used. In the experiment 3, all groups displayed adequate sperm quality values, but higher in vitro fertility parameters were obtained for spermatozoa sorted in presence of EDTA in the sheath fluid and egg yolk (EY) in the collection media when compared with those sorted in absence of these protective agents. No differences in penetration rates between unsorted highly diluted (control) and sorted sperm in the presence of EDTA and EY were observed. In conclusion, fertilizing ability was compromised in sex-sorted sperm. The addition of EDTA to sheath fluid and EY to collection medium improved boar sperm fertilizing ability, and both agents should be included as essential media components in future studies. Copyright © 2013 Elsevier Inc. All rights reserved.

Implications of QRIS Design for the Distribution of Program Ratings and Linkages between Ratings and Observed Quality. OPRE Research Brief 2014-33

ERIC Educational Resources Information Center

Tout, Kathryn; Chien, Nina; Rothenberg, Laura; Li, Weilin

2014-01-01

This Brief compares three hypothetical Quality Rating and Improvement Systems (QRIS) that use different rating structures: block, points, and hybrid. Because the quality standards in the hypothetical QRIS are held relatively constant across structures, analyses can be conducted to determine how structure relates to key QRIS outcomes. Three…

7 CFR 1210.307 - Handle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack...

7 CFR 1210.307 - Handle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack...

7 CFR 1210.307 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack...

7 CFR 1210.307 - Handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE WATERMELON RESEARCH AND PROMOTION PLAN Watermelon Research and Promotion Plan Definitions § 1210.307 Handle. Handle means to grade, pack...

[A workplace intervention aimed at increasing awareness in nursing personnel performing manual handling activities].

PubMed

Scorpiniti, A; Lorusso, A; L'Abbate, N

2007-01-01

Here we describe a workplace intervention aimed at reducing the risk of low back pain in nursing personnel. The intervention we carried out included a specific ergonomic training and an exercise program according to the Feldenkrais Method. After the intervention, we evaluated its effect on the execution of manual handling activities in nurses. We found an increased rate of correct manual handling in the post-intervention period.

Broach Handle Design Changes Force Distribution in the Femur During Total Hip Arthroplasty.

PubMed

Greenhill, Dustin A; Abbasi, Pooyan; Darvish, Kurosh; Star, Andrew M

2017-06-01

Curved broach handles were developed to overcome limited surgical exposures during total hip arthroplasty. Some authors report increased intraoperative fracture rates during limited exposures. This study evaluates mechanical force ratios transmitted to the bone while broaching with curved vs straight handles. An experimental model utilized a 6-axis load cell to measure force distributions produced by 4 different broach handles, each with increasing offset and curvature. Handles were separately impacted and dynamic variables assessed. Handles were then digitized using a high-resolution optical system and a finite element analysis (FEA) was performed to account for trabecular bone and vary the location of mallet impact. Off-axis forces, broaching construct moments, and stress within surrounding bone were computed. Using the experimental model, high-offset handles lost on average 4% more hammering force to the horizontal axis. When the FEA utilized moduli of elasticity to estimate broaching through osteoporotic trabecular bone, horizontally displaced forces (toward cortical bone) were magnified from 4% to a maximum value of 52%. Both the experimental construct and FEA confirmed that larger offset handles increase moment-to-force ratios up to 163%-235%, thus rotating the proximal and distal ends of the broach toward cortical bone. Broach handle design is an important determinant of resultant forces transmitted to the broach (and ultimately the bone) during total hip arthroplasty. Unwanted off-axis forces and enhanced rotational dynamics may play a role in intraoperative fractures during femoral canal preparation. Copyright © 2016 Elsevier Inc. All rights reserved.

How Would Programs Rate under California's Proposed Quality Rating and Improvement System? Evidence from Statewide and County Data on Early Care and Education Program Quality. Documented Briefing

ERIC Educational Resources Information Center

Karoly, Lynn A.; Zellman, Gail L.

2012-01-01

In 2010, the California Early Learning Quality Improvement System (CAEL QIS) Advisory Committee recommended a structure for a voluntary quality rating and improvement system (QRIS) that could apply to the state's 11,000 licensed centers and 36,600 licensed family child care homes (FCCHs). The proposed design consisted of an unweighted block system…

Improvement of storage, handling, and transportability of fine coal. Quarterly technical progress report number 8, October 1--December 31, 1995

DOE Office of Scientific and Technical Information (OSTI.GOV)

NONE

The Mulled Coal process was developed as a means of overcoming the adverse handling characteristics of wet fine coal without thermal drying. The process involves the addition of a low cost, harmless reagent to wet fine coal using off-the-shelf mixing equipment. Based on laboratory- and bench-scale testing, Mulled coal can be stored, shipped, and burned without causing any of the plugging, pasting, carryback and freezing problems normally associated with wet coal. On the other hand, Mulled Coal does not cause the fugitive and airborne dust problems normally associated with thermally dried coal. The objectives of this project are to demonstratemore » that: the Mulled Coal process, which has been proved to work on a wide range of wet fine coals at bench scale, will work equally well on a continuous basis, producing consistent quality, and at a convincing rate of production in a commercial coal preparation plant; the wet product from a fine coal cleaning circuit can be converted to a solid fuel form for ease of handling and cost savings in storage and rail car transportation; and a wet fine coal product thus converted to a solid fuel form, can be stored, shipped, and burned with conventional fuel handling, transportation, and combustion systems.« less

Differences in Muscle Activity During Cable Resistance Training Are Influenced by Variations in Handle Types.

PubMed

Rendos, Nicole K; Heredia Vargas, Héctor M; Alipio, Taislaine C; Regis, Rebeca C; Romero, Matthew A; Signorile, Joseph F

2016-07-01

Rendos, NK, Heredia Vargas, HM, Alipio, TC, Regis, RC, Romero, MA, and Signorile, JF. Differences in muscle activity during cable resistance training are influenced by variations in handle types. J Strength Cond Res 30(7): 2001-2009, 2016-There has been a recent resurgence in the use of cable machines for resistance training allowing movements that more effectively simulate daily activities and sports-specific movements. By necessity, these devices require a machine/human interface through some type of handle. Considerable data from material handling, industrial engineering, and exercise training studies indicate that handle qualities, especially size and shape, can significantly influence force production and muscular activity, particularly of the forearm muscles, which affect the critical link in activities that require object manipulation. The purpose for this study was to examine the influence of three different handle conditions: standard handle (StandH), ball handle with the cable between the index and middle fingers (BallIM), and ball handle with the cable between the middle and ring fingers (BallMR), on activity levels (rmsEMG) of the triceps brachii lateral and long heads (TriHLat, TriHLong), brachioradialis (BR), flexor carpi radialis (FCR), extensor carpi ulnaris, and extensor digitorum (ED) during eight repetitions of standing triceps pushdown performed from 90° to 0° elbow flexion at 1.5 s per contractile stage. Handle order was randomized. No significant differences were seen for triceps or BR rmsEMG across handle conditions; however, relative patterns of activation did vary for the forearm muscles by handle condition, with more coordinated activation levels for the FCR and ED during the ball handle conditions. In addition, the rmsEMG for the ED was significantly higher during the BallIM than any other condition and during the BallMR than the StandH. These results indicate that the use of ball handles with the cable passing between different fingers

Grain Handling and Storage.

ERIC Educational Resources Information Center

Harris, Troy G.; Minor, John

This text for a secondary- or postecondary-level course in grain handling and storage contains ten chapters. Chapter titles are (1) Introduction to Grain Handling and Storage, (2) Elevator Safety, (3) Grain Grading and Seed Identification, (4) Moisture Control, (5) Insect and Rodent Control, (6) Grain Inventory Control, (7) Elevator Maintenance,…

Poor semen quality may contribute to recent decline in fertility rates.

PubMed

Jensen, Tina Kold; Carlsen, Elisabeth; Jørgensen, Niels; Berthelsen, Jørgen G; Keiding, Niels; Christensen, Kaare; Petersen, Jørgen Holm; Knudsen, Lisbeth B; Skakkebaek, Niels E

2002-06-01

During past decades, we have witnessed a remarkable decline in fertility rates (number of births per 1000 women of reproductive age) in the industrialized world. It seems beyond doubt that the enormous social changes of our societies play the major role in this decline, but can it be attributed to changing social structures alone or is a reduced fecundity in the population also a factor? To address this we have focused on trends in teenage pregnancies (which to a large extent are unplanned). During the period in question fertility rates among 15-19 year old Danish women have been falling and the decline in fertility rate is not counterbalanced by an increase in the rate of induced abortion. When seen together with recent results from Denmark, which have shown that more than 30% of 19 year old men from the general population now have sperm counts in the subfertile range, we argue that this fall may not be attributable to social factors, changes in conception practices or diminished sexual activity alone. It seems reasonable also to consider widespread poor semen quality among men as a potential contributing factor to low fertility rates among teenagers. Due to the concern caused by the low sperm count among younger Danish men, the Danish Ministries of Health and Environment have launched a surveillance programme which includes an annual examination of the semen quality in 600 young Danes from the general population. We propose that researchers in other countries with low and falling fertility rates among young women should consider the possibility that semen quality of their younger male cohorts may also have deteriorated.

[Clinical everyday ethics-support in handling moral distress? : Evaluation of an ethical decision-making model for interprofessional clinical teams].

PubMed

Tanner, S; Albisser Schleger, H; Meyer-Zehnder, B; Schnurrer, V; Reiter-Theil, S; Pargger, H

2014-06-01

High-tech medicine and cost rationing provoke moral distress up to burnout syndromes. The consequences are severe, not only for those directly involved but also for the quality of patient care and the institutions. The multimodal model METAP (Modular, Ethical, Treatment, Allocation, Process) was developed as clinical everyday ethics to support the interprofessional ethical decision-making process. The distinctive feature of the model lays in education concerning ethics competence in dealing with difficult treatment decisions. METAP has been evaluated for quality testing. The research question of interest was whether METAP supports the handling of moral distress. The evaluation included 3 intensive care units and 3 geriatric units. In all, 33 single and 9 group interviews were held with 24 physicians, 44 nurses, and 9 persons from other disciplines. An additional questionnaire was completed by 122 persons (return rate 57%). Two-thirds of the interview answers and 55% of the questionnaire findings show that clinical everyday ethics supports the handling of moral distress, especially for interdisciplinary communication and collaboration and for the explanation and evaluation of treatment goals. METAP does not provide support for persons who are rarely confronted with ethical problems or have not applied the model long enough yet. To a certain degree, moral distress is unavoidable and must be addressed as an interprofessional problem. Herein, clinical everyday ethics may provide targeted support for ethical decision-making competence.

7 CFR 905.9 - Handle or ship.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Handle or ship. 905.9 Section 905.9 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... TANGELOS GROWN IN FLORIDA Order Regulating Handling Definitions § 905.9 Handle or ship. Handle or ship...

7 CFR 948.8 - Handle or ship.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport, sell...

7 CFR 905.9 - Handle or ship.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Handle or ship. 905.9 Section 905.9 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... TANGELOS GROWN IN FLORIDA Order Regulating Handling Definitions § 905.9 Handle or ship. Handle or ship...

7 CFR 905.9 - Handle or ship.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Handle or ship. 905.9 Section 905.9 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... TANGELOS GROWN IN FLORIDA Order Regulating Handling Definitions § 905.9 Handle or ship. Handle or ship...

7 CFR 948.8 - Handle or ship.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport, sell...

7 CFR 905.9 - Handle or ship.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Handle or ship. 905.9 Section 905.9 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... TANGELOS GROWN IN FLORIDA Order Regulating Handling Definitions § 905.9 Handle or ship. Handle or ship...

7 CFR 948.8 - Handle or ship.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport, sell...

7 CFR 948.8 - Handle or ship.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Handle or ship. 948.8 Section 948.8 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Order Regulating Handling Definitions § 948.8 Handle or ship. Handle or ship means to transport, sell...

Modeling the time--varying subjective quality of HTTP video streams with rate adaptations.

PubMed

Chen, Chao; Choi, Lark Kwon; de Veciana, Gustavo; Caramanis, Constantine; Heath, Robert W; Bovik, Alan C

2014-05-01

Newly developed hypertext transfer protocol (HTTP)-based video streaming technologies enable flexible rate-adaptation under varying channel conditions. Accurately predicting the users' quality of experience (QoE) for rate-adaptive HTTP video streams is thus critical to achieve efficiency. An important aspect of understanding and modeling QoE is predicting the up-to-the-moment subjective quality of a video as it is played, which is difficult due to hysteresis effects and nonlinearities in human behavioral responses. This paper presents a Hammerstein-Wiener model for predicting the time-varying subjective quality (TVSQ) of rate-adaptive videos. To collect data for model parameterization and validation, a database of longer duration videos with time-varying distortions was built and the TVSQs of the videos were measured in a large-scale subjective study. The proposed method is able to reliably predict the TVSQ of rate adaptive videos. Since the Hammerstein-Wiener model has a very simple structure, the proposed method is suitable for online TVSQ prediction in HTTP-based streaming.

FUEL HANDLING MECHANISM

DOEpatents

Koch, L.J.; Hutter, E.

1960-02-01

A remotely operable handling device specifically adapted for the handling of vertically disposed fuel rods in a nuclear reactor was developed. The device consists essentially of an elongated tubular member having a gripping device at the lower end of the pivoted jaw type adapted to grip an enlarged head on the upper end of the workpiece. The device includes a sensing element which engages the enlarged head and is displaced to remotely indicate when the workpiece is in the proper position to be engaged by the jaws.

A pressure ulcer and fall rate quality composite index for acute care units: A measure development study.

PubMed

Boyle, Diane K; Jayawardhana, Ananda; Burman, Mary E; Dunton, Nancy E; Staggs, Vincent S; Bergquist-Beringer, Sandra; Gajewski, Byron J

2016-11-01

Composite indices are single measures that combine the strengths of two or more individual measures and provide broader, easy-to-use measures for evaluation of provider performance and comparisons across units and hospitals to support quality improvement. The study objective was to develop a unit-level inpatient composite nursing care quality performance index-the Pressure Ulcer and Fall Rate Quality Composite Index. Two-phase measure development study. 5144 patient care units in 857 United States hospitals participating in the National Database of Nursing Quality Indictors ® during the year 2013. The Pressure Ulcer and Fall Rate Quality Composite Index was developed in two phases. In Phase 1 the formula was generated using a utility function and generalized penalty analysis. Experts with experience in healthcare quality measurement provided the point of indicator equivalence. In Phase 2 initial validity evidence was gathered based on hypothesized relationships between the Pressure Ulcer and Fall Rate Quality Composite Index and other variables using two-level (unit, hospital) hierarchical linear mixed modeling. The Pressure Ulcer and Fall Rate Quality Composite Index=100-PUR-FR, where PUR is pressure ulcer rate and FR is total fall rate. Higher scores indicate better quality. Bland-Altman plots demonstrated agreement between pairs of experts and provided evidence for inter-rater reliability of the formula. The validation process demonstrated that higher registered nurse skill mix, higher percent of registered nurses with a baccalaureate in nursing or higher degree, higher percent of registered nurses with national specialty certification, and lower percent of hours supplied by agency staff were significantly associated with higher Pressure Ulcer and Fall Rate Quality Composite Index scores. Higher percentages of unit patients at risk for a hospital-acquired pressure ulcer and higher unit rates of physical restraint use were not associated with higher Pressure

A PRESSURE ULCER AND FALL RATE QUALITY COMPOSITE INDEX FOR ACUTE CARE UNITS: A MEASURE DEVELOPMENT STUDY

PubMed Central

Jayawardhana, Ananda; Burman, Mary E.; Dunton, Nancy E.; Staggs, Vincent S.; Bergquist-Beringer, Sandra; Gajewski, Byron J.

2016-01-01

Background Composite indices are single measures that combine the strengths of two or more individual measures and provide broader, easy-to-use measures for evaluation of provider performance and comparisons across units and hospitals to support quality improvement. Objective The study objective was to develop a unit-level inpatient composite nursing care quality performance index – the Pressure Ulcer and Fall Rate Quality Composite Index. Design Two-phase measure development study. Settings 5,144 patient care units in 857 United States hospitals participating in the National Database of Nursing Quality Indictors® during the year 2013. Methods The Pressure Ulcer and Fall Rate Quality Composite Index was developed in two phases. In Phase 1 the formula was generated using a utility function and generalized penalty analysis. Experts with experience in healthcare quality measurement provided the point of indicator equivalence. In Phase 2 initial validity evidence was gathered based on hypothesized relationships between the Pressure Ulcer and Fall Rate Quality Composite Index and other variables using two-level (unit, hospital) hierarchical linear mixed modeling. Results The Pressure Ulcer and Fall Rate Quality Composite Index = 100 − PUR − FR, where PUR is pressure ulcer rate and FR is total fall rate. Higher scores indicate better quality. Bland-Altman plots demonstrated agreement between pairs of experts and provided evidence for inter-rater reliability of the formula. The validation process demonstrated that higher registered nurse skill mix, higher percent of registered nurses with a baccalaureate in nursing or higher degree, higher percent of registered nurses with national specialty certification, and lower percent of hours supplied by agency staff were significantly associated with higher Pressure Ulcer and Fall Rate Quality Composite Index scores. Higher percentages of unit patients at risk for a hospital-acquired pressure ulcer and higher unit rates of

Impact of increased collection rates and the use of commingled collection systems on the quality of recovered paper. Part 1: increased collection rates.

PubMed

Miranda, Ruben; Monte, M; Blanco, Angeles

2011-11-01

The recovery and utilization of recovered paper have increased over past decades all over the world due to economic, environmental, and social issues. However, it is well known that an extended recovered paper collection is detrimental to its quality, either by the exploitation of lower quality sources such as households, or the spreading of commingled systems instead of selective collection systems. The influence of these two factors was assessed by analyzing the quality of different recovered paper grades used as raw material in a mill located in Madrid (Spain) producing newsprint and light weight coated paper from recovered paper. Part 1 of the paper deals with the impact of increased collection rates on the quality of recovered paper and Part 2 with the use of commingled collection systems. Results of Part 1 show that increased collection rates have a large impact on the quality of the recovered paper. The quality, measured as total unusable material and moisture contents, had deteriorated very rapidly in only 4 years (2005-2008) as a consequence of increased collection rates. Collection rates increased in Spain from 58.5% to 68.6% during this period, resulting in more than 50% increase of total unusable material and 25% of moisture content. The downgrading of the quality of recovered paper is one of the major threats for extending the current limits of paper recycling. Therefore, future challenge is to increase its availability but maintaining its quality. Copyright © 2011 Elsevier Ltd. All rights reserved.

Coaching and Quality Assistance in Quality Rating Improvement Systems: Approaches Used by TA Providers to Improve Quality in Early Care and Education Programs and Home-Based Settings

ERIC Educational Resources Information Center

Smith, Sheila; Robbins, Taylor; Schneider, Will; Kreader, J. Lee; Ong, Christine

2012-01-01

Quality Rating Improvement Systems (QRISs) commonly offer on-site technical assistance (TA) and coaching to help early care and education settings achieve quality improvements and a higher QRIS rating. In surveys of administrators overseeing statewide QRISs, almost all states reported the use of on-site TA and coaching in both center-based and…

Contributors to Patients' Ratings of Quality of Care Among Ethnically Diverse Patients with Type 2 Diabetes.

PubMed

Choi, Sarah E; Ngo-Metzger, Quyen; Billimek, John; Greenfield, Sheldon; Kaplan, Sherrie H; Sorkin, Dara H

2016-04-01

We examined racial/ethnic differences in patients' ratings of components of interpersonal quality [participatory decision making (PDM) style, being treated as an equal partner, and feelings of trust], and evaluated the association between each of these components and patients' ratings of overall healthcare quality among non-Hispanic white (NHW), Vietnamese American, and Mexican American patients with type 2 diabetes. The findings indicated that although all three components were significantly associated with ratings of overall healthcare quality, the significant interactions between race/ethnicity and both PDM style (β = -0.09, p < 0.01) and equal partner (β = -0.06, p < 0.05) for the Vietnamese American patients suggested that the relationship between these components and patients' ratings of healthcare quality were less strong among Vietnamese American patients than among the NHW patients. Understanding racial/ethnic differences in the components of interpersonal quality that are associated with patients' ratings of overall healthcare quality is an important step for improving patients' experiences of their own care.

Neonatal handling (resilience) attenuates water-avoidance stress induced enhancement of chronic mechanical hyperalgesia in the rat

PubMed Central

Alvarez, Pedro; Levine, Jon D.; Green, Paul G.

2015-01-01

Chronic stress is well known to exacerbate pain. We tested the hypothesis that neonatal handling, which induces resilience to the negative impact of stress by increasing the quality and quantity of maternal care, attenuates the mechanical hyperalgesia produced by water-avoidance stress in the adult rat. Neonatal male rats underwent the handling protocol on postnatal days 2–9, weaned at 21 days and tested for muscle mechanical nociceptive threshold at postnatal days 50–75. Decrease in mechanical nociceptive threshold in skeletal muscle in adult rats, produced by exposure to water-avoidance stress, was significantly attenuated by neonatal handling. Neonatal handling also attenuated the mechanical hyperalgesia produced by intramuscular administration of the pronociceptive inflammatory mediator, prostaglandin E2 in rats exposed as adults to water-avoidance stress. Neonatal handling, which induces a smaller corticosterone response in adult rats exposed to a stressor as well as changes in central nervous system neurotransmitter systems, attenuates mechanical hyperalgesia produced by water-avoidance stress and enhanced prostaglandin hyperalgesia in adult animals. PMID:25637700

7 CFR 58.443 - Whey handling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Whey handling. 58.443 Section 58.443 Agriculture... Procedures § 58.443 Whey handling. (a) Adequate sanitary facilities shall be provided for the handling of whey. If outside, necessary precautions shall be taken to minimize flies, insects and development of...

7 CFR 945.9 - Ship or handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to place...

7 CFR 927.8 - Ship or handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any point...

7 CFR 927.8 - Ship or handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any point...

7 CFR 945.9 - Ship or handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to place...

7 CFR 927.8 - Ship or handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any point...

7 CFR 945.9 - Ship or handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Ship or handle. 945.9 Section 945.9 Agriculture... DESIGNATED COUNTIES IN IDAHO, AND MALHEUR COUNTY, OREGON Order Regulating Handling Definitions § 945.9 Ship or handle. Ship or handle means to pack, sell, consign, transport or in any other way to place...

7 CFR 927.8 - Ship or handle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any point...

7 CFR 927.8 - Ship or handle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 7 Agriculture 8 2014-01-01 2014-01-01 false Ship or handle. 927.8 Section 927.8 Agriculture... Order Regulating Handling Definitions § 927.8 Ship or handle. Ship or handle means to sell, deliver, consign, transport or ship pears within the production area or between the production area and any point...

Diet quality and cognitive function in an urban sample: findings from the Healthy Aging in Neighborhoods of Diversity across the Life Span (HANDLS) study.

PubMed

Wright, Regina S; Waldstein, Shari R; Kuczmarski, Marie Fanelli; Pohlig, Ryan T; Gerassimakis, Constance S; Gaynor, Beatrice; Evans, Michele K; Zonderman, Alan B

2017-01-01

Poor diet quality contributes to morbidity, including poor brain health outcomes such as cognitive decline and dementia. African Americans and individuals living in poverty may be at greater risk for cognitive decrements from poor diet quality. Cross-sectional. Baltimore, MD, USA. Participants were 2090 African Americans and Whites (57 % female, mean age=47·9 years) who completed two 24 h dietary recalls. We examined cognitive performance and potential interactions of diet quality with race and poverty status using baseline data from the Healthy Aging in Neighborhoods of Diversity across the Life Span (HANDLS) study. Healthy Eating Index-2010 (HEI-2010) scores were calculated and interpreted using federal guidelines. A neurocognitive test battery was administered to evaluate cognitive function over several domains. Linear regression analyses showed that lower HEI-2010 scores were associated with poorer verbal learning and memory (P<0·05) after adjustment for covariates. Diet quality within the sample was poor. Significant interactions of HEI-2010 and poverty status (all P<0·05) indicated that higher diet quality was associated with higher performance on tests of attention and cognitive flexibility, visuospatial ability and perceptual speed among those below the poverty line. No significant race interactions emerged. Higher diet quality was associated with better performance on two measures of verbal learning and memory, irrespective of race and poverty status. Findings suggest that diet quality and cognitive function are likely related at the population level. Future research is needed to determine whether the association is clinically significant.

Effects of box handle position and carrying range on bi-manual carrying capacity for females.

PubMed

Wu, Swei-Pi; Loiu, Yi; Chien, Te Hong

2015-01-01

This study utilizes a psychophysical approach to examine the effects on carrying capacity for bi-manual carrying tasks involving different handle positions and carrying ranges. A total of 16 female subjects participated in the experiment in groups of two people, and each group of subjects performed the tasks in a random order with 12 different combinations of carrying task. The independent variables are handle position (upper, middle, lower) and carrying range (F-F: floor height carried to floor height, F-W: floor height carried to waist height, W-W: waist height carried to waist height, W-F: waist height carried to floor height), the dependent variable is the maximum acceptable carried weight (MAWC), heart rate (HR), and the rating of perceived exertion (RPE). The results show that the handle position has a significant effect on MAWC and overall RPE but no significant effect on HR. Carrying range has a significant effect on the MAWC and HR, but no significant effect on overall HR. The handle position and carrying range have a significant interaction on the MAWC and HR. The RPE for different body parts shows significant differences, and the hands feel the most tired. Overall, this study confirms that the lower handle position with the W-W carrying range is the best combination for a two-person carrying task.

High performance interconnection between high data rate networks

NASA Technical Reports Server (NTRS)

Foudriat, E. C.; Maly, K.; Overstreet, C. M.; Zhang, L.; Sun, W.

1992-01-01

The bridge/gateway system needed to interconnect a wide range of computer networks to support a wide range of user quality-of-service requirements is discussed. The bridge/gateway must handle a wide range of message types including synchronous and asynchronous traffic, large, bursty messages, short, self-contained messages, time critical messages, etc. It is shown that messages can be classified into three basic classes, synchronous and large and small asynchronous messages. The first two require call setup so that packet identification, buffer handling, etc. can be supported in the bridge/gateway. Identification enables resequences in packet size. The third class is for messages which do not require call setup. Resequencing hardware based to handle two types of resequencing problems is presented. The first is for a virtual parallel circuit which can scramble channel bytes. The second system is effective in handling both synchronous and asynchronous traffic between networks with highly differing packet sizes and data rates. The two other major needs for the bridge/gateway are congestion and error control. A dynamic, lossless congestion control scheme which can easily support effective error correction is presented. Results indicate that the congestion control scheme provides close to optimal capacity under congested conditions. Under conditions where error may develop due to intervening networks which are not lossless, intermediate error recovery and correction takes 1/3 less time than equivalent end-to-end error correction under similar conditions.

Pre-slaughter sound levels and pre-slaughter handling from loading at the farm till slaughter influence pork quality.

PubMed

Vermeulen, L; Van de Perre, V; Permentier, L; De Bie, S; Verbeke, G; Geers, R

2016-06-01

This study investigates the relationship between sound levels, pre-slaughter handling during loading and pork quality. Pre-slaughter variables were investigated from loading till slaughter. A total of 3213 pigs were measured 30 min post-mortem for pH(30LT) (M. Longissimus thoracis). First, a sound level model for the risk to develop PSE meat was established. The difference in maximum and mean sound level during loading, mean sound level during lairage and mean sound level prior to stunning remained significant within the model. This indicated that sound levels during loading had a significant added value to former sound models. Moreover, this study completed the global classification checklist (Vermeulen et al., 2015a) by developing a linear mixed model for pH(30LT) and PSE prevalence, with the difference in maximum and mean sound level measured during loading, the feed withdrawal period and the difference in temperature during loading and lairage. Hence, this study provided new insights over previous research where loading procedures were not included. Copyright © 2016 Elsevier Ltd. All rights reserved.

Complaint handling in healthcare: expectation gaps between physicians and the public; results of a survey study.

PubMed

Friele, R D; Reitsma, P M; de Jong, J D

2015-10-01

Patients who submit complaints about the healthcare they have received are often dissatisfied with the response to their complaints. This is usually attributed to the failure of physicians to respond adequately to what complainants want, e.g. an apology or an explanation. However, expectations of complaint handling among the public may colour how they evaluate the way their own complaint is handled. This descriptive study assesses expectations of complaint handling in healthcare among the public and physicians. Negative public expectations and the gap between these expectations and those of physicians may explain patients' dissatisfaction with complaints procedures. We held two surveys; one among physicians, using a panel of 3366 physicians (response rate 57 %, containing all kinds of physicians like GP's, medical specialist and physicians working in a nursing home) and one among the public, using the Dutch Healthcare Consumer Panel (n = 1422, response rate 68 %). We asked both panels identical questions about their expectations of how complaints are handled in healthcare. Differences in expectation scores between the public and the physicians were tested using non-parametric tests. The public have negative expectations about how complaints are handled. Physician's expectations are far more positive, demonstrating large expectation gaps between physicians and the public. The large expectation gap between the public and physicians means that when they meet because of complaint, they are likely to start off with opposite expectations of the situation. This is no favourable condition for a positive outcome of a complaints procedure. The negative public preconceptions about the way their complaint will be handled will prove hard to change during the process of complaints handling. People tend to see what they thought would happen, almost inevitably leading to a negative judgement about how their complaint was handled.

Pre-slaughter stress and pork quality

NASA Astrophysics Data System (ADS)

Stajković, S.; Teodorović, V.; Baltić, M.; Karabasil, N.

2017-09-01

Stress is an inevitable consequence of handling of animals for slaughter. Stress conditions during transport, lairage and at slaughter induce undesirable effects on the end quality of meat such as pale, soft, exudative meat and dark firm dry meat. Hence, it is very important to define appropriate parameters for objective assessment of level of stress. Attempts to define measures of stress have been difficult and no physiological parameter has been successfully used to evaluate stress situations. One physiological change in swine associated with animal handling stress and with pork quality is an increase in blood lactate concentration. Plasma cortisol was thought to be an appropriate indicator of stress, but the concentration was not consistently changed by different stressors. Therefore, finding alternative parameters reacting to stressors, such as acute phase proteins, would be of great value for the objective evaluation of level of stress and meat quality. As the stress during pre-slaughter handling is unavoidable, the final goal is to improve transport and slaughter conditions for the animal and, as a consequence, meat quality and animal welfare.

Recommendations for Collection and Handling of Specimens From Group Breast Cancer Clinical Trials

PubMed Central

Leyland-Jones, Brian R.; Ambrosone, Christine B.; Bartlett, John; Ellis, Matthew J.C.; Enos, Rebecca A.; Raji, Adekunle; Pins, Michael R.; Zujewski, Jo Anne; Hewitt, Stephen M.; Forbes, John F.; Abramovitz, Mark; Braga, Sofia; Cardoso, Fatima; Harbeck, Nadia; Denkert, Carsten; Jewell, Scott D.

2008-01-01

Recommendations for specimen collection and handling have been developed for adoption across breast cancer clinical trials conducted by the Breast International Group (BIG)-sponsored Groups and the National Cancer Institute (NCI)-sponsored North American Cooperative Groups. These recommendations are meant to promote identifiable standards for specimen collection and handling within and across breast cancer trials, such that the variability in collection/handling practices that currently exists is minimized and specimen condition and quality are enhanced, thereby maximizing results from specimen-based diagnostic testing and research. Three working groups were formed from the Cooperative Group Banking Committee, BIG groups, and North American breast cancer cooperative groups to identify standards for collection and handling of (1) formalin-fixed, paraffin-embedded (FFPE) tissue; (2) blood and its components; and (3) fresh/frozen tissue from breast cancer trials. The working groups collected standard operating procedures from multiple group specimen banks, administered a survey on banking practices to those banks, and engaged in a series of discussions from 2005 to 2007. Their contributions were synthesized into this document, which focuses primarily on collection and handling of specimens to the point of shipment to the central bank, although also offers some guidance to central banks. Major recommendations include submission of an FFPE block, whole blood, and serial serum or plasma from breast cancer clinical trials, and use of one fixative and buffer type (10% neutral phosphate-buffered formalin, pH 7) for FFPE tissue across trials. Recommendations for proper handling and shipping were developed for blood, serum, plasma, FFPE, and fresh/frozen tissue. PMID:18955459

Establishing the overall service quality of engineering education: fuzzy logic approach

NASA Astrophysics Data System (ADS)

Shekhar, N. Chandra; Venkatasubbaiah, K.; Kandukuria, N. R.

2012-12-01

Measuring overall service quality (OSQ) is gaining prominence in higher education due to the increased competition among engineering education institutions (EEIs) and growing awareness about value for money among the public. Determination of OSQ on certain institutional aspects is done by various agencies throughout the world. Each system uses a different set of weighted indicators to measure the overall service quality of institutions. Five service quality factors, namely professionalism, integrated education, facilities, responsiveness and empathy are considered in the study. Trapezoidal fuzzy numbers are used to determine the aggregate weights of the factors to handle the vagueness present in the linguistic values of the stakeholders' subjective opinions. Final weights of the factors are assessed by taking the distances of each factor between Fuzzy Positive Ideal Rating and Fuzzy Negative Ideal Rating. An illustrative study is presented to determine the OSQ of EEIs. The results help to focus on the factors which need immediate attention to enhance the quality of EEIs.

Decision method for optimal selection of warehouse material handling strategies by production companies

NASA Astrophysics Data System (ADS)

Dobos, P.; Tamás, P.; Illés, B.

2016-11-01

Adequate establishment and operation of warehouse logistics determines the companies’ competitiveness significantly because it effects greatly the quality and the selling price of the goods that the production companies produce. In order to implement and manage an adequate warehouse system, adequate warehouse position, stock management model, warehouse technology, motivated work force committed to process improvement and material handling strategy are necessary. In practical life, companies have paid small attantion to select the warehouse strategy properly. Although it has a major influence on the production in the case of material warehouse and on smooth costumer service in the case of finished goods warehouse because this can happen with a huge loss in material handling. Due to the dynamically changing production structure, frequent reorganization of warehouse activities is needed, on what the majority of the companies react basically with no reactions. This work presents a simulation test system frames for eligible warehouse material handling strategy selection and also the decision method for selection.

Modern methods for the quality management of high-rate melt solidification

NASA Astrophysics Data System (ADS)

Vasiliev, V. A.; Odinokov, S. A.; Serov, M. M.

2016-12-01

The quality management of high-rate melt solidification needs combined solution obtained by methods and approaches adapted to a certain situation. Technological audit is recommended to estimate the possibilities of the process. Statistical methods are proposed with the choice of key parameters. Numerical methods, which can be used to perform simulation under multifactor technological conditions, and an increase in the quality of decisions are of particular importance.

Adjusted hospital death rates: a potential screen for quality of medical care.

PubMed

Dubois, R W; Brook, R H; Rogers, W H

1987-09-01

Increased economic pressure on hospitals has accelerated the need to develop a screening tool for identifying hospitals that potentially provide poor quality care. Based upon data from 93 hospitals and 205,000 admissions, we used a multiple regression model to adjust the hospitals crude death rate. The adjustment process used age, origin of patient from the emergency department or nursing home, and a hospital case mix index based on DRGs (diagnostic related groups). Before adjustment, hospital death rates ranged from 0.3 to 5.8 per 100 admissions. After adjustment, hospital death ratios ranged from 0.36 to 1.36 per 100 (actual death rate divided by predicted death rate). Eleven hospitals (12 per cent) were identified where the actual death rate exceeded the predicted death rate by more than two standard deviations. In nine hospitals (10 per cent), the predicted death rate exceeded the actual death rate by a similar statistical margin. The 11 hospitals with higher than predicted death rates may provide inadequate quality of care or have uniquely ill patient populations. The adjusted death rate model needs to be validated and generalized before it can be used routinely to screen hospitals. However, the remaining large differences in observed versus predicted death rates lead us to believe that important differences in hospital performance may exist.

HAND TRUCK FOR HANDLING EQUIPMENT

DOEpatents

King, D.W.

1959-02-24

A truck is described for the handling of large and relatively heavy pieces of equipment and particularly for the handling of ion source units for use in calutrons. The truck includes a chassis and a frame pivoted to the chassis so as to be operable to swing in the manner of a boom. The frame has spaced members so arranged that the device to be handled can be suspended between or passed between these spaced members and also rotated with respect to the frame when the device is secured to the spaced members.

Sleep Quality Estimation based on Chaos Analysis for Heart Rate Variability

NASA Astrophysics Data System (ADS)

Fukuda, Toshio; Wakuda, Yuki; Hasegawa, Yasuhisa; Arai, Fumihito; Kawaguchi, Mitsuo; Noda, Akiko

In this paper, we propose an algorithm to estimate sleep quality based on a heart rate variability using chaos analysis. Polysomnography(PSG) is a conventional and reliable system to diagnose sleep disorder and to evaluate its severity and therapeatic effect, by estimating sleep quality based on multiple channels. However, a recording process requires a lot of time and a controlled environment for measurement and then an analyzing process of PSG data is hard work because the huge sensed data should be manually evaluated. On the other hand, it is focused that some people make a mistake or cause an accident due to lost of regular sleep and of homeostasis these days. Therefore a simple home system for checking own sleep is required and then the estimation algorithm for the system should be developed. Therefore we propose an algorithm to estimate sleep quality based only on a heart rate variability which can be measured by a simple sensor such as a pressure sensor and an infrared sensor in an uncontrolled environment, by experimentally finding the relationship between chaos indices and sleep quality. The system including the estimation algorithm can inform patterns and quality of own daily sleep to a user, and then the user can previously arranges his life schedule, pays more attention based on sleep results and consult with a doctor.

Evaluating the effectiveness of a participatory ergonomics approach in reducing the risk and severity of injuries from manual handling.

PubMed

Carrivick, Philip J W; Lee, Andy H; Yau, Kelvin K W; Stevenson, Mark R

2005-06-22

Manual handling is the greatest contributor to non-fatal injury and disease in the workplace, commonly accounting for one-third of national injury counts. Interventional strategies that have focused on selecting or modifying the worker have been ineffective in reducing injury risk. In recent times, participatory ergonomics has been widely adopted as a process to reduce the risk of injury from manual handling but it is not well validated as an intervention. This study evaluated the effectiveness of a participatory ergonomics risk assessment approach in reducing the rate and severity of injuries from manual and non-manual handling sustained by a cohort of 137 cleaners within a hospital setting. The date of injury and the workers' compensation claim cost and hours lost from work were obtained for each injury incurred during the 4-year pre-intervention and 3-year intervention period. The age, gender and hours worked were ascertained for every cleaner whether injured or not. Using generalized linear mixed modelling analysis, reductions of rate of injury by two-thirds, workers' compensation claim costs by 62% and hours lost by 35% for manual handling injuries were found to be associated with the intervention period. Although the cleaners experienced a significant intervention period reduction in non-manual handling injury rate, the corresponding changes in severity of injury were not significant. The success of the intervention supports the adoption of a participatory ergonomics approach in reducing the rate and consequence of injuries in the workplace.

30 CFR 75.818 - Use of insulated cable handling equipment.

Code of Federal Regulations, 2011 CFR

2011-07-01

... personal protective equipment capable of providing protection against shock hazard must be used to prevent... protective equipment must— (1) Have a voltage rating of at least Class 1 (7,500 volts) that meets or exceeds... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Use of insulated cable handling equipment. 75...

30 CFR 75.818 - Use of insulated cable handling equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... personal protective equipment capable of providing protection against shock hazard must be used to prevent... protective equipment must— (1) Have a voltage rating of at least Class 1 (7,500 volts) that meets or exceeds... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Use of insulated cable handling equipment. 75...

Handling missing values in the MDS-UPDRS.

PubMed

Goetz, Christopher G; Luo, Sheng; Wang, Lu; Tilley, Barbara C; LaPelle, Nancy R; Stebbins, Glenn T

2015-10-01

This study was undertaken to define the number of missing values permissible to render valid total scores for each Movement Disorder Society Unified Parkinson's Disease Rating Scale (MDS-UPDRS) part. To handle missing values, imputation strategies serve as guidelines to reject an incomplete rating or create a surrogate score. We tested a rigorous, scale-specific, data-based approach to handling missing values for the MDS-UPDRS. From two large MDS-UPDRS datasets, we sequentially deleted item scores, either consistently (same items) or randomly (different items) across all subjects. Lin's Concordance Correlation Coefficient (CCC) compared scores calculated without missing values with prorated scores based on sequentially increasing missing values. The maximal number of missing values retaining a CCC greater than 0.95 determined the threshold for rendering a valid prorated score. A second confirmatory sample was selected from the MDS-UPDRS international translation program. To provide valid part scores applicable across all Hoehn and Yahr (H&Y) stages when the same items are consistently missing, one missing item from Part I, one from Part II, three from Part III, but none from Part IV can be allowed. To provide valid part scores applicable across all H&Y stages when random item entries are missing, one missing item from Part I, two from Part II, seven from Part III, but none from Part IV can be allowed. All cutoff values were confirmed in the validation sample. These analyses are useful for constructing valid surrogate part scores for MDS-UPDRS when missing items fall within the identified threshold and give scientific justification for rejecting partially completed ratings that fall below the threshold. © 2015 International Parkinson and Movement Disorder Society.

Quality in Colonoscopy: Beyond the Adenoma Detection Rate Fever

PubMed Central

Taveira, Filipe; Areia, Miguel; Elvas, Luís; Alves, Susana; Brito, Daniel; Saraiva, Sandra; Cadime, Ana Teresa

2017-01-01

Background Colonoscopy quality is a hot topic in gastroenterological communities, with several actual guidelines focusing on this aspect. Although the adenoma detection rate (ADR) is the single most important indicator, several other metrics are described and need reporting. Electronic medical reports are essential for the audit of quality indicators; nevertheless, they have proved not to be faultless. Aim The aim of this study was to analyse and audit quality indicators (apart from ADR) using only our internal electronic endoscopy records as a starting point for improvement. Methods An analysis of electronically recorded information of 8,851 total colonoscopies from a single tertiary centre from 2010 to 2015 was performed. Results The mean patient age was 63.4 ± 8.5 years; 45.5% of them were female, and in 14.6% sedation was used. Photographic documentation was done in 98.4% with 10.7 photographs on average, and 37.4% reports had <8 pictures per exam. Bowel preparation was rated as adequate in 67%, fair in 27% and inadequate in 4.9% of cases. The adjusted caecal intubation rate (CIR) was 92%, while negative predictors were inadequate preparation (OR 119, 95% CI 84–170), no sedation (OR 2.39, 95% CI 1.81–3.15), female gender (OR 1.61, 95% CI 1.38–1.88) and age ≥65 years (OR 1.56, 95% CI 1.34–1.82). In 28% of patients, a snare polypectomy was performed, correlating with adequate preparation (OR 5.75, 95% CI 3.90–8.48), male gender (OR 1.82, 95% CI 1.64–2.01) and age ≥65 years (OR 1.25, 95% CI 1.13–1.37; p < 0.01) as positive predictors. An annual evolution was observed with improvements in photographic documentation (10.7 vs. 12.9; p < 0.001), CIR (91 vs. 94%; p = 0.002) and “adequate” bowel preparation (p = 0.004). Conclusions: There is much more to report than the ADR to ensure quality in colonoscopy practice. Better registry systematization and integrated software should be goals to achieve in the short term. PMID:29255755

Habituating to handling: factors affecting preorbital gland opening in red deer calves.

PubMed

Ceacero, F; Landete-Castillejos, T; Bartošová, J; García, A J; Bartoš, L; Komárková, M; Gallego, L

2014-09-01

The preorbital gland plays not only an olfactory role in cervids but also a visual one. Opening this gland is an easy way for the calf to communicate with the mother, indicating hunger/satiety, stress, pain, fear, or excitement. This information can be also useful for farm operators to assess how fast the calves habituate to handling routines and to detect those calves that do not habituate and may suffer chronic stress in the future. Thirty-one calves were subjected to 2 consecutive experiments to clarify if observing preorbital gland opening is related to habituation to handling in red deer calves (Cervus elaphus). Calves were born in 3 different paddocks, handled as newborns (Exp. 1), and then subjected to the same routine handling but with different periodicity: every 1, 2, or 3 wk (Exp. 2). In Exp. 1, preorbital gland opening was recorded in newborns during an initial handling (including weighing, ear tagging, and sex determination). Preorbital gland opening occurred in 93% of calves during this procedure and was not affected by sex, time since birth, or birth weight. Experiment 2 consisted of measuring preorbital opening during the same routine handling (weighing, blood sampling, and rump touching to assess body condition) when calves were 1, 3, and 5 mo old. Binary logistic regression showed that gland opening was associated with habituation to handling, since at 1 and 3 mo the probability of opening the gland decreased with the number of handlings that a calf experienced before (P = 0.008 and P = 0.028, respectively). However, there were no further changes in preorbital gland opening rate in the 5-mo-old calves (P = 0.182). The significant influence of the number of previous handlings on the probability of opening the preorbital gland was confirmed through generalized linear model with repeated measures (P = 0.007). Preorbital gland opening decreased along the phases of the study. Nevertheless, we found a significant trend in individuals to keep similar

Correlations between quality ratings of skilled nursing facilities and multidrug-resistant urinary tract infections.

PubMed

Gucwa, Azad L; Dolar, Veronika; Ye, Chao; Epstein, Stephanie

2016-11-01

The purpose of this study was to determine risk factors for the acquisition of urinary tract infections (UTIs) and multidrug-resistant organisms (MDROs) in residents of skilled nursing facilities (SNFs). Using the informational database provided by the Centers for Medicare and Medicaid Services (CMS), a retrospective logistic regression was performed on 1,523 urine cultures from 12 SNFs located in Long Island, New York. Of the 1,142 positive urine cultures, Escherichia coli was most prevalent. Additionally, 164 (14.4%) of the UTIs were attributed to an MDRO. In multivariate logistic regression, sex and overall quality rating predicted the occurrence of UTIs, whereas identification of MDROs was dependent on the level of nursing care received. The mean predicted probability of UTIs and receipt of contaminated samples was inversely dependent on the facility's rating, where the likelihood increased as overall quality ratings decreased. The CMS's quality rating system may provide some insight into the status of infection control practices in SNFs. The results of this study suggest that potential consumers should focus on the overall star ratings and the competency of the nursing staff in these facilities rather than on individual quality measures. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Handling an Asthma Flare-Up

MedlinePlus

... Videos for Educators Search English Español Handling an Asthma Flare-Up KidsHealth / For Kids / Handling an Asthma ... español Cómo controlar las crisis asmáticas What's an Asthma Flare-Up? If you have asthma , you probably ...

7 CFR 1205.312 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE COTTON RESEARCH AND PROMOTION Cotton Research and Promotion Order Definitions § 1205.312 Handle. Handle means to harvest, gin, warehouse, compress, purchase, market, transport, or otherwise acquire ownership or control of cotton. [31 FR 16758...

7 CFR 983.14 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... Orders; Fruits, Vegetables, Nuts), DEPARTMENT OF AGRICULTURE PISTACHIOS GROWN IN CALIFORNIA, ARIZONA, AND NEW MEXICO Definitions § 983.14 Handle. Handle means to engage in: (a) Receiving pistachios; (b) Hulling and drying pistachios; (c) Further preparing pistachios by sorting, sizing, shelling, roasting...

7 CFR 1219.11 - Handle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass avocados...

7 CFR 1219.11 - Handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass avocados...

7 CFR 1219.11 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass avocados...

7 CFR 1219.11 - Handle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE HASS AVOCADO PROMOTION, RESEARCH, AND INFORMATION Hass Avocado Promotion, Research, and Information Order Definitions § 1219.11 Handle. Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass avocados...

Moments of speaking and silencing: Nurses share their experiences of manual handling in healthcare.

PubMed

Kay, Kate; Evans, Alicia; Glass, Nel

2015-01-01

Nursing care involves complex patient handling tasks, resulting in high musculoskeletal injury rates. Epidemiological studies from the 1980s estimated a lifetime prevalence of lower back injuries for nurses between 35 and 80%. National and international studies continue to mirror these findings. Despite the development of programs intended to reduce manual handling injuries, sustainable solutions remain elusive. This paper reports on a study of nurses speaking about their perspectives on current manual handling practices. Qualitative research conducted in 2012 investigated nurses' perceptions and experiences relating to manual handling in the healthcare context and their participation in injury prevention programs. There were two research methods: semi-structured interviews and researcher reflective journaling. The research was framed in critical emancipatory methodology. Thirteen nurses from two Australian states participated in the study. Thematic analysis revealed an overarching theme of 'power relations' with a subcategory of '(mis)power' that comprised two subthemes, these being 'how to practice' and 'voicing practice issues'. Specifically, this paper explores nurses verbalising their views in the workplace and responses which left them feeling silenced, punished and disillusioned. The findings suggest that the sociopolitical context within which nurses practice impacts upon their ability to voice concerns or ideas related to manual handling. Inclusion of nurses in the manual handling dialogue may generate an expanded understanding of, and the potential to transform, manual handling practices in healthcare environments.

The social buffering effect of playful handling on responses to repeated intraperitoneal injections in laboratory rats.

PubMed

Cloutier, Sylvie; Wahl, Kim; Baker, Chelsea; Newberry, Ruth C

2014-03-01

Handling small animals for veterinary and experimental procedures can negatively affect animal wellbeing. We hypothesized that playful handling (tickling) would decrease stress associated with repeated injections in adult laboratory rats, especially those with prior tickling experience. We compared responses of 4 groups of male Sprague-Dawley rats to intraperitoneal injection of saline daily for 10 d. Rats either tickled or not tickled as juveniles (2 min/d for 21 d) were exposed as adults to either a passive hand or tickling for 2 min immediately before and after injections. Rates of vocalization (22- and 50-kHz ultrasonic vocalizations (USV), indicative of negative and positive affective states, respectively, and audible calls indicative of pain and discomfort) were quantified before, during, and after injection. Tickling before and after injection, especially when combined with juvenile tickling experience (ending 40 to 50 d earlier), increased 50-kHz USV rates before and after injection, reduced audible call rate during injection, and decreased the duration of the injection procedure. The treatments did not affect indicators of physiologic stress (body weight change; fecal corticosteroid levels). We conclude that playful handling performed in association with a mildly aversive procedure serves as a useful refinement by inducing a positive affective state that mitigates the aversiveness of the procedure and makes rats easier to handle, especially when they have been accustomed to tickling as juveniles.

The Social Buffering Effect of Playful Handling on Responses to Repeated Intraperitoneal Injections in Laboratory Rats

PubMed Central

Cloutier, Sylvie; Wahl, Kim; Baker, Chelsea; Newberry, Ruth C

2014-01-01

Handling small animals for veterinary and experimental procedures can negatively affect animal wellbeing. We hypothesized that playful handling (tickling) would decrease stress associated with repeated injections in adult laboratory rats, especially those with prior tickling experience. We compared responses of 4 groups of male Sprague–Dawley rats to intraperitoneal injection of saline daily for 10 d. Rats either tickled or not tickled as juveniles (2 min/d for 21 d) were exposed as adults to either a passive hand or tickling for 2 min immediately before and after injections. Rates of vocalization (22- and 50-kHz ultrasonic vocalizations (USV), indicative of negative and positive affective states, respectively, and audible calls indicative of pain and discomfort) were quantified before, during, and after injection. Tickling before and after injection, especially when combined with juvenile tickling experience (ending 40 to 50 d earlier), increased 50-kHz USV rates before and after injection, reduced audible call rate during injection, and decreased the duration of the injection procedure. The treatments did not affect indicators of physiologic stress (body weight change; fecal corticosteroid levels). We conclude that playful handling performed in association with a mildly aversive procedure serves as a useful refinement by inducing a positive affective state that mitigates the aversiveness of the procedure and makes rats easier to handle, especially when they have been accustomed to tickling as juveniles. PMID:24602543

Effect of paper quality on the response rate to a postal survey: A randomised controlled trial. [ISRCTN32032031

PubMed Central

Clark, T Justin; Khan, Khalid S; Gupta, Janesh K

2001-01-01

Background Response rates to surveys are declining and this threatens the validity and generalisability of their findings. We wanted to determine whether paper quality influences the response rate to postal surveys Methods A postal questionnaire was sent to all members of the British Society of Gynaecological Endoscopy (BSGE). Recipients were randomised to receiving the questionnaire printed on standard quality paper or high quality paper. Results The response rate for the recipients of high quality paper was 43/195 (22%) and 57/194 (29%) for standard quality paper (relative rate of response 0.75, 95% CI 0.33–1.05, p = 0.1 Conclusion The use of high quality paper did not increase response rates to a questionnaire survey of gynaecologists affiliated to an endoscopic society. PMID:11782286

7 CFR 1216.12 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale...

7 CFR 1216.12 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE PEANUT PROMOTION, RESEARCH, AND INFORMATION ORDER Peanut Promotion, Research, and Information Order Definitions § 1216.12 Handle. Handle means... peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale...

7 CFR 926.9 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements and... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... cranberries or processed cranberries up to, but not including, the retail level. Effective Date Note: At 71 FR...

Pituitary-adrenocortical adjustments to transport stress in horses with previous different handling and transport conditions

PubMed Central

Fazio, E.; Medica, P.; Cravana, C.; Ferlazzo, and A.

2016-01-01

Aim: The changes of the hypothalamic pituitary adrenal (HPA) axis response to a long distance transportation results in increase of adrenocorticotropic hormone (ACTH) and cortisol levels. The purpose of the study was to quantify the level of short-term road transport stress on circulating ACTH and cortisol concentrations, related to the effect of previous handling and transport experience of horses. Materials and Methods: The study was performed on 56 healthy horses after short-term road transport of 30 km. The horses were divided into four groups, Groups A, B, C, and D, with respect to the handling quality: Good (Groups A and B), bad (Group D), and minimal handling (Group C) conditions. According to the previous transport, experience horses were divided as follows: Horses of Groups A and D had been experienced long-distance transportation before; horses of Groups B and C had been limited experience of transportation. Results: One-way RM-ANOVA showed significant effects of transport on ACTH changes in Groups B and C and on cortisol changes in both Groups A and B. Groups A and B showed lower baseline ACTH and cortisol values than Groups C and D; Groups A and B showed lower post-transport ACTH values than Groups C and D. Groups A, B, and C showed lower post-transport cortisol values than Group D. Only Groups A and B horses have shown an adequate capacity of stress response to transportation. Conclusion: The previous transport experience and quality of handling could influence the HPA axis physiological responses of horses after short-term road transport. PMID:27651674

Social Media and Rating Sites as Tools to Understanding Quality of Care: A Scoping Review

PubMed Central

Van de Belt, Tom H; Engelen, Lucien JLPG; Schoonhoven, Lisette; Kool, Rudolf B

2014-01-01

Background Insight into the quality of health care is important for any stakeholder including patients, professionals, and governments. In light of a patient-centered approach, it is essential to assess the quality of health care from a patient’s perspective, which is commonly done with surveys or focus groups. Unfortunately, these “traditional” methods have significant limitations that include social desirability bias, a time lag between experience and measurement, and difficulty reaching large groups of people. Information on social media could be of value to overcoming these limitations, since these new media are easy to use and are used by the majority of the population. Furthermore, an increasing number of people share health care experiences online or rate the quality of their health care provider on physician rating sites. The question is whether this information is relevant to determining or predicting the quality of health care. Objective The goal of our research was to systematically analyze the relation between information shared on social media and quality of care. Methods We performed a scoping review with the following goals: (1) to map the literature on the association between social media and quality of care, (2) to identify different mechanisms of this relationship, and (3) to determine a more detailed agenda for this relatively new research area. A recognized scoping review methodology was used. We developed a search strategy based on four themes: social media, patient experience, quality, and health care. Four online scientific databases were searched, articles were screened, and data extracted. Results related to the research question were described and categorized according to type of social media. Furthermore, national and international stakeholders were consulted throughout the study, to discuss and interpret results. Results Twenty-nine articles were included, of which 21 were concerned with health care rating sites. Several studies

Social media and rating sites as tools to understanding quality of care: a scoping review.

PubMed

Verhoef, Lise M; Van de Belt, Tom H; Engelen, Lucien J L P G; Schoonhoven, Lisette; Kool, Rudolf B

2014-02-20

Insight into the quality of health care is important for any stakeholder including patients, professionals, and governments. In light of a patient-centered approach, it is essential to assess the quality of health care from a patient's perspective, which is commonly done with surveys or focus groups. Unfortunately, these "traditional" methods have significant limitations that include social desirability bias, a time lag between experience and measurement, and difficulty reaching large groups of people. Information on social media could be of value to overcoming these limitations, since these new media are easy to use and are used by the majority of the population. Furthermore, an increasing number of people share health care experiences online or rate the quality of their health care provider on physician rating sites. The question is whether this information is relevant to determining or predicting the quality of health care. The goal of our research was to systematically analyze the relation between information shared on social media and quality of care. We performed a scoping review with the following goals: (1) to map the literature on the association between social media and quality of care, (2) to identify different mechanisms of this relationship, and (3) to determine a more detailed agenda for this relatively new research area. A recognized scoping review methodology was used. We developed a search strategy based on four themes: social media, patient experience, quality, and health care. Four online scientific databases were searched, articles were screened, and data extracted. Results related to the research question were described and categorized according to type of social media. Furthermore, national and international stakeholders were consulted throughout the study, to discuss and interpret results. Twenty-nine articles were included, of which 21 were concerned with health care rating sites. Several studies indicate a relationship between information

Determining the predictors of change in quality of life self-ratings and carer-ratings for community-dwelling people with Alzheimer disease.

PubMed

Bosboom, Pascalle R; Alfonso, Helman; Almeida, Osvaldo P

2013-01-01

The aim of this study was to determine the factors that mediate changes in Health Related Quality of Life (HRQoL) ratings by community-dwelling people with Alzheimer disease (AD) and carers over a period of 18 months. We completed an 18-month longitudinal study of 80 community-dwelling older adults diagnosed with probable AD of mild or moderate severity (NINCDS-ADRD criteria) and their family carers. The primary outcome of interest was the 18-month change in HRQoL ratings as measured with the Quality of Life-AD (QoL-AD) (by carer and by self). Explanatory variables included demographics, lifestyle, cognition, awareness, psychopathology, burden-of-care, use of medication, and functionality in daily life. We found a significant decline (8.7%, P=0.003) in QoL-AD carer-ratings, but not in self-ratings. The final parsimonious model of predictors of changes in QoL-AD self-ratings explained 22.6% of the variance; only changes on Hospital Anxiety and Depression Scale Anxiety retained significance. The final model of predictors of changes in carer-ratings explained 55.0% of the variance: that is, changes on Informant Questionnaire on Cognitive Decline in the Elderly, changes on Hospital Anxiety and Depression Scale Depression, practicing hobbies at 18 months, and number of visit(s) or admission(s) to hospital. HRQoL self-ratings and carer-ratings of community-dwelling people with AD do not decline at same rate over 18 months and changes are associated with different factors. Interventions designed to optimize quality of life of people with AD should consider carefully whose HRQoL ratings they wish to change.

Reducing the Primary Cesarean Birth Rate: A Quality Improvement Project.

PubMed

Javernick, Julie A; Dempsey, Amy

2017-07-01

Research continues to support vaginal birth as the safest mode of childbirth, but despite this, cesarean birth has become the most common surgical procedure performed on women. The rate has increased 500% since the 1970s without a corresponding improvement in maternal or neonatal outcomes. A Colorado community hospital recognized that its primary cesarean birth rate was higher than national and state benchmark levels. To reduce this rate, the hospital collaborated with its largest maternity care provider group to implement a select number of physiologic birth practices and measure improvement in outcomes. Using a pre- and postprocess measure study design, the quality improvement project team identified and implemented 3 physiologic birth parameters over a 12-month period that have been shown to promote vaginal birth. These included reducing elective induction of labor in women less than 41 weeks' gestation; standardizing triage to admit women at greater than or equal to 4 cm dilation; and increasing the use of intermittent auscultation as opposed to continuous fetal monitoring for fetal surveillance. The team also calculated each obstetrician-gynecologist's primary cesarean birth rate monthly and delivered these rates to the providers. Outcomes showed that the provider group decreased its primary cesarean birth rate from 28.9% to 12.2% in the 12-month postprocess measure period. The 57.8% decrease is statistically significant (odds ratio [OR], 0.345; z = 6.52, P < .001; 95% confidence interval [CI], 0.249-0.479). While this quality improvement project cannot be translated to other settings, promotion of physiologic birth practices, along with audit and feedback, had a statistically significant impact on the primary cesarean birth rate for this provider group and, consequently, on the community hospital where they attend births. © 2017 by the American College of Nurse-Midwives.

[Process-oriented quality management in the hospital].

PubMed

Wolters, H G

1998-03-01

Procedures and experiences concerning the implementation of quality management in a midsize hospital with 6 medical disciplines are described. Quality of infrastructure was checked with lists and the quality of medical performance assessed by means of standardized numerical audit with all professional groups. Weaknesses were identified by comparing the result to each quality indicator with target standards. As examples, causal relations and consequences of deficiencies in clinical care documentation, scheme of preoperative diagnosis, co-ordination of surgical procedures and handling of complications are given in more detail. Obstacles were rated depending on frequency and risk potential, sometimes cost effectiveness. Members of all professional groups and departments involved participated in trouble solving teams to which external expert assistance was provided. For example, interventions leading to improved co-ordination of surgical activities and their impacts are specified. Improving systematically the quality of clinical procedures is one gateway to establish quality management in hospitals continuously and thoroughly becoming an integrated part of the corporate culture. Investment of resources is necessary but justified by midrange benefits.

The natural angle between the hand and handle and the effect of handle orientation on wrist radial/ulnar deviation during maximal push exertions.

PubMed

Young, Justin G; Lin, Jia-Hua; Chang, Chien-Chi; McGorry, Raymond W

2013-01-01

The purpose of this experiment was to quantify the natural angle between the hand and a handle, and to investigate three design factors: handle rotation, handle tilt and between-handle width on the natural angle as well as resultant wrist radial/ulnar deviation ('RUD') for pushing tasks. Photographs taken of the right upper limb of 31 participants (14 women and 17 men) performing maximal seated push exertions on different handles were analysed. Natural hand/handle angle and RUD were assessed. It was found that all of the three design factors significantly affected natural handle angle and wrist RUD, but participant gender did not. The natural angle between the hand and the cylindrical handle was 65 ± 7°. Wrist deviation was reduced for handles that were rotated 0° (horizontal) and at the narrow width (31 cm). Handles that were tilted forward 15° reduced radial deviation consistently (12-13°) across handle conditions. Manual materials handling (MMH) tasks involving pushing have been related to increased risk of musculoskeletal injury. This study shows that handle orientation influences hand and wrist posture during pushing, and suggests that the design of push handles on carts and other MMH aids can be improved by adjusting their orientation to fit the natural interface between the hand and handle.

Perceived comfort level of medical students and residents in handling clinical ethics issues.

PubMed

Silverman, Henry J; Dagenais, Julien; Gordon-Lipkin, Eliza; Caputo, Laura; Christian, Matthew W; Maidment, Bert W; Binstock, Anna; Oyalowo, Akinbowale; Moni, Malini

2013-01-01

Studies have shown that medical students and residents believe that their ethics preparation has been inadequate for handling ethical conflicts. The objective of this study was to determine the self-perceived comfort level of medical students and residents in confronting clinical ethics issues. Clinical medical students and residents at the University of Maryland School of Medicine completed a web-based survey between September 2009 and February 2010. The survey consisted of a demographic section, questions regarding the respondents' sense of comfort in handling a variety of clinical ethics issues, and a set of knowledge-type questions in ethics. Survey respondents included 129 medical students (response rate of 40.7%) and 207 residents (response rate of 52.7%). There were only a few clinical ethics issues with which more than 70% of the respondents felt comfortable in addressing. Only a slight majority (60.8%) felt prepared, in general, to handle clinical situations involving ethics issues, and only 44.1% and 53.2% agreed that medical school and residency training, respectively, helped prepare them to handle such issues. Prior ethics training was not associated with these responses, but there was an association between the level of training (medical students vs residents) and the comfort level with many of the clinical ethics issues. Medical educators should include ethics educational methods within the context of real-time exposure to medical ethics dilemmas experienced by physicians-in-training.

7 CFR 1207.307 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in the...

7 CFR 1219.11 - Handle.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Handle. 1219.11 Section 1219.11 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS.... Handle means to pack, process, transport, purchase, or in any other way to place or cause Hass avocados...

21 CFR 820.140 - Handling.

Code of Federal Regulations, 2010 CFR

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Handling. 820.140 Section 820.140 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL DEVICES..., contamination, or other adverse effects to product do not occur during handling. ...

9 CFR 3.118 - Handling.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

9 CFR 3.118 - Handling.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

9 CFR 3.118 - Handling.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

9 CFR 3.118 - Handling.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

9 CFR 3.118 - Handling.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 9 Animals and Animal Products 1 2011-01-01 2011-01-01 false Handling. 3.118 Section 3.118 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE ANIMAL WELFARE STANDARDS Specifications for the Humane Handling, Care, Treatment, and Transportation of Marine...

7 CFR 1207.307 - Handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in the...

7 CFR 1207.307 - Handle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in the...

7 CFR 1207.307 - Handle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in the...

7 CFR 1207.307 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... AND ORDERS; MISCELLANEOUS COMMODITIES), DEPARTMENT OF AGRICULTURE POTATO RESEARCH AND PROMOTION PLAN Potato Research and Promotion Plan Definitions § 1207.307 Handle. Handle means to grade, pack, process, sell, transport, purchase, or in any other way to place potatoes or cause potatoes to be placed in the...

A comparison of the in vitro moisture vapour transmission rate and in vivo fluid-handling capacity of six adhesive foam dressings to a newly reformulated adhesive foam dressing.

PubMed

Zehrer, Cindy L; Holm, David; Solfest, Staci E; Walters, Shelley-Ann

2014-12-01

This study compared moisture vapour transmission rate (MVTR) and wear time or fluid-handling capacities of six adhesive foam dressings to a reformulated control dressing. Standardised in vitro MVTR methodology and a previously published in vivo artificial wound model (AWM) were used. Mean inverted MVTR for the reformulated dressing was 12 750 g/m(2) /24 hours and was significantly higher than four of the six comparator dressings (P < 0·0001), which ranged from 830 to 11 360 g/m(2) /24 hours. Mean upright MVTR for the reformulated dressing was 980 g/m(2) /24 hours and was significantly different than all of the comparator dressings (P < 0·0001), which ranged from 80 to 1620 g/m(2) /24 hours (three higher/three lower). The reformulated dressing median wear time ranged from 6·1 to >7·0 days, compared with 1·0 to 3·5 days for the comparator dressings (P = 0·0012 to P < 0·0001). The median fluid volume handled ranged from 78·0 to >87 ml compared with 13·0 to 44·5 ml for the comparator dressings (P = 0·0007 to P < 0·001). Interestingly, inverted MVTR did not correspond well to the AWM. These results suggest that marked differences exist between the dressings in terms of both MVTR and wear time or fluid-handling capacity. Furthermore, high inverted MVTR does not necessarily predict longer wear time or fluid-handling capacities of absorbent dressings. © 2013 The Authors. International Wound Journal © 2013 Medicalhelplines.com Inc and John Wiley & Sons Ltd.

[Can quality of life in psychotherapy be measured with clinician-ratings? A comparison of patient- and clinician-ratings using the SF-8].

PubMed

Schulz, H; Harfst, T; Andreas, S; Kawski, S; Koch, U; Rabung, S

2009-10-01

Quality of life is a major criterion of the outcome of psychotherapeutic interventions. The concept of quality of life emphasizes patient self-ratings. However, they can be burdensome or inappropriate in some cases. Therefore we have compared self-ratings and clinician-ratings of quality of life. Self- and clinician-ratings of the SF-8 (1-week recall version) were measured from consecutive samples of 1 812 inpatients from eleven psychotherapeutic clinics at admission and at discharge six weeks later. A physical summary score (PSS) and a mental summary score (MSS) were calculated. Pearson product-moment correlations were used. Self- and clinician-ratings of the PSS correlate r=0.48 at admission and r=0.58 at discharge, of the MSS r=0.46 and r=0.51, respectively. Concerning single items we find the highest correlation for item 4 (bodily pain: r=0.53 and r=0.55), the lowest for item 6 (social functioning: r=0.26 and r=0.30). Change scores of the PSS correlate r=0.20, of the MSS r=0.32. Correlations differ between diagnostic groups: Correlations are low for patients with either schizophrenia (F2), depressive episode (F32) or personality disorder (F60-62), comparatively higher for patients with dysthymia. Comparing correlations across the 11 clinics reveals substantial differences, for the MSS ranging from r=0.38 to r=0.58 at admission and r=0.27 to r=0.68 at discharge. Patient self-ratings of quality of life as a psychotherapeutic outcome measure using the SF-8 Health Survey could not be substituted by clinician-ratings, they should be used as complements. Georg Thieme Verlag KG Stuttgart . New York.

WASTE HANDLING BUILDING ELECTRICAL SYSTEM DESCRIPTION DOCUMENT

DOE Office of Scientific and Technical Information (OSTI.GOV)

S.C. Khamamkar

2000-06-23

The Waste Handling Building Electrical System performs the function of receiving, distributing, transforming, monitoring, and controlling AC and DC power to all waste handling building electrical loads. The system distributes normal electrical power to support all loads that are within the Waste Handling Building (WHB). The system also generates and distributes emergency power to support designated emergency loads within the WHB within specified time limits. The system provides the capability to transfer between normal and emergency power. The system provides emergency power via independent and physically separated distribution feeds from the normal supply. The designated emergency electrical equipment will bemore » designed to operate during and after design basis events (DBEs). The system also provides lighting, grounding, and lightning protection for the Waste Handling Building. The system is located in the Waste Handling Building System. The system consists of a diesel generator, power distribution cables, transformers, switch gear, motor controllers, power panel boards, lighting panel boards, lighting equipment, lightning protection equipment, control cabling, and grounding system. Emergency power is generated with a diesel generator located in a QL-2 structure and connected to the QL-2 bus. The Waste Handling Building Electrical System distributes and controls primary power to acceptable industry standards, and with a dependability compatible with waste handling building reliability objectives for non-safety electrical loads. It also generates and distributes emergency power to the designated emergency loads. The Waste Handling Building Electrical System receives power from the Site Electrical Power System. The primary material handling power interfaces include the Carrier/Cask Handling System, Canister Transfer System, Assembly Transfer System, Waste Package Remediation System, and Disposal Container Handling Systems. The system interfaces with the MGR

77 FR 23117 - Rigging Equipment for Material Handling Construction Standard; Correction and Technical Amendment

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-18

...OSHA is correcting its sling standard for construction titled ``Rigging Equipment for Material Handling'' by removing the rated capacity tables and making minor, nonsubstantive revisions to the regulatory text.

50 CFR 14.111 - Handling.

Code of Federal Regulations, 2010 CFR

2010-10-01

... and Fisheries UNITED STATES FISH AND WILDLIFE SERVICE, DEPARTMENT OF THE INTERIOR TAKING, POSSESSION..., EXPORTATION, AND TRANSPORTATION OF WILDLIFE Standards for the Humane and Healthful Transport of Wild Mammals and Birds to the United States § 14.111 Handling. (a) Care shall be exercised to avoid handling the...

Fluid handling equipment: A compilation

NASA Technical Reports Server (NTRS)

1976-01-01

Devices and techniques used in fluid-handling and vacuum systems are described. Section 1 presents several articles on fluid lines and tubing. Section 2 describes a number of components such as valves, filters, and regulators. The last section contains descriptions of a number of innovative fluid-handling systems.

SLUG HANDLING DEVICES

DOEpatents

Gentry, J.R.

1958-09-16

A device is described for handling fuel elements of a neutronic reactor. The device consists of two concentric telescoped contalners that may fit about the fuel element. A number of ratchet members, equally spaced about the entrance to the containers, are pivoted on the inner container and spring biased to the outer container so thnt they are forced to hear against and hold the fuel element, the weight of which tends to force the ratchets tighter against the fuel element. The ratchets are released from their hold by raising the inner container relative to the outer memeber. This device reduces the radiation hazard to the personnel handling the fuel elements.

Delaware Stars for Early Success. QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Delaware's Stars for Early Success prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators…

Vermont STep Ahead Recognition System: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Vermont's STep Ahead Recognition System (STARS) prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for All Child Care Programs;…

Kentucky STARS for KIDS NOW: QRS Profile. The Child Care Quality Rating System (QRS) Assessment

ERIC Educational Resources Information Center

Child Trends, 2010

2010-01-01

This paper presents a profile of Kentucky's STARS for KIDS NOW prepared as part of the Child Care Quality Rating System (QRS) Assessment Study. The profile consists of several sections and their corresponding descriptions including: (1) Program Information; (2) Rating Details; (3) Quality Indicators for Center-Based Programs; (4) Indicators for…

Analytical study of beam handling and emittance control

NASA Astrophysics Data System (ADS)

Thompson, James R.; Sloan, M. L.

1993-12-01

The thrust of our research on beam handling and emittance control was to explore how one might design high current electron accelerators, with the preservation of high beam quality designed as the primary design consideration. We considered high current, induction linacs in the parameter class of the ETA/ATA accelerators at LLNL, but with improvements to the accelerator gap design and other features to permit a significant increase in the deliverable beam brightness. Our approach for beam quality control centered on the use of solenoidal magnetic focusing through such induction accelerators, together with gently-shaped (adiabatic) acceleration gaps. This approach offers several tools for the control of beam quality. The strength and axial variation in the solenoidal magnetic field may be designed, as may the length and shape of the acceleration gaps, the loading of the gaps, and the axial spacing from gap to gap. This research showed that each of these design features may individually be optimized to contribute to improved beam quality control, and by exploiting these features, it appears feasible to produce high current, high energy electron beams possessing breakthrough beam quality and brightness. Applications which have been technologically unachievable may for the first time become possible. One such application is the production of high performance free electron lasers at very short wavelengths, extending down to the optical (less than 1 micron) regime.

Analysis of multiple activity manual materials handling tasks using A Guide to Manual Materials Handling.

PubMed

Mital, A

1999-01-01

Manual handling of materials continues to be a hazardous activity, leading to a very significant number of severe overexertion injuries. Designing jobs that are within the physical capabilities of workers is one approach ergonomists have adopted to redress this problem. As a result, several job design procedures have been developed over the years. However, these procedures are limited to designing or evaluating only pure lifting jobs or only the lifting aspect of a materials handling job. This paper describes a general procedure that may be used to design or analyse materials handling jobs that involve several different kinds of activities (e.g. lifting, lowering, carrying, pushing, etc). The job design/analysis procedure utilizes an elemental approach (breaking the job into elements) and relies on databases provided in A Guide to Manual Materials Handling to compute associated risk factors. The use of the procedure is demonstrated with the help of two case studies.

Information Handling is the Problem

NASA Technical Reports Server (NTRS)

Malin, Jane T.

2001-01-01

This slide presentation reviews the concerns surrounding the automation of information handling. There are two types of decision support software that supports most Space Station Flight Controllers. one is very simple, and the other is very complex. A middle ground is sought. This is the reason for the Human Centered Autonomous and Assistant Systems Testbed (HCAAST) Project. The aim is to study flight controllers at work, and in the bigger picture, with particular attention to how they handle information and how coordination of multiple teams is performed. The focus of the project is on intelligent assistants to assist in handling information for the flight controllers.

7 CFR 926.9 - Handle.

Code of Federal Regulations, 2013 CFR

2013-01-01

... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current of...

7 CFR 926.9 - Handle.

Code of Federal Regulations, 2012 CFR

2012-01-01

... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current of...

7 CFR 926.9 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current of...

7 CFR 926.9 - Handle.

Code of Federal Regulations, 2014 CFR

2014-01-01

... REQUIREMENTS APPLICABLE TO CRANBERRIES NOT SUBJECT TO THE CRANBERRY MARKETING ORDER § 926.9 Handle. Handle... contract carrier of cranberries owned by another person) fresh or processed cranberries produced within or outside the United States or in any other way to place fresh or processed cranberries into the current of...

[Quality Management and Quality Specifications of Laboratory Tests in Clinical Studies--Challenges in Pre-Analytical Processes in Clinical Laboratories].

PubMed

Ishibashi, Midori

2015-01-01

The cost, speed, and quality are the three important factors recently indicated by the Ministry of Health, Labour and Welfare (MHLW) for the purpose of accelerating clinical studies. Based on this background, the importance of laboratory tests is increasing, especially in the evaluation of clinical study participants' entry and safety, and drug efficacy. To assure the quality of laboratory tests, providing high-quality laboratory tests is mandatory. For providing adequate quality assurance in laboratory tests, quality control in the three fields of pre-analytical, analytical, and post-analytical processes is extremely important. There are, however, no detailed written requirements concerning specimen collection, handling, preparation, storage, and shipping. Most laboratory tests for clinical studies are performed onsite in a local laboratory; however, a part of laboratory tests is done in offsite central laboratories after specimen shipping. As factors affecting laboratory tests, individual and inter-individual variations are well-known. Besides these factors, standardizing the factors of specimen collection, handling, preparation, storage, and shipping, may improve and maintain the high quality of clinical studies in general. Furthermore, the analytical method, units, and reference interval are also important factors. It is concluded that, to overcome the problems derived from pre-analytical processes, it is necessary to standardize specimen handling in a broad sense.

7 CFR 996.4 - Handle.

Code of Federal Regulations, 2011 CFR

2011-01-01

... DOMESTIC AND IMPORTED PEANUTS MARKETED IN THE UNITED STATES Definitions § 996.4 Handle. Handle means to... imported peanuts and in the shipment (except as a common or contract carrier of peanuts owned by another) or sale of cleaned-inshell or shelled peanuts or other activity causing peanuts to enter into human...

Assessing the Validity of the Qualistar Early Learning Quality Rating and Improvement System as a Tool for Improving Child-Care Quality

ERIC Educational Resources Information Center

Zellman, Gail L.; Perlman, Michal; Le, Vi-Nhuan; Setodji, Claude Messan

2008-01-01

As a result of the generally low quality of child care in the United States and the increased emphasis on accountability in education policy, quality rating systems (QRSs) are proliferating in the child-care arena. QRSs assess child-care providers on multiple dimensions of quality and integrate these assessments into an easily understood summary…

A new approach to handling incoming verifications.

PubMed

Luizzo, Anthony; Roy, Bill; Luizzo, Philip

2016-10-01

Outside requests for data on current or former employees are handled in different ways by healthcare organizations and present considerable liability risks if a corporate policy for handling such risks is not in place. In this article, the authors present a strategy for responsible handling of sensitive information.

9 CFR 114.11 - Storage and handling.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 9 Animals and Animal Products 1 2012-01-01 2012-01-01 false Storage and handling. 114.11 Section... BIOLOGICAL PRODUCTS § 114.11 Storage and handling. Biological products at licensed establishments shall be protected at all times against improper storage and handling. Completed product shall be kept under...

9 CFR 114.11 - Storage and handling.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 9 Animals and Animal Products 1 2014-01-01 2014-01-01 false Storage and handling. 114.11 Section... BIOLOGICAL PRODUCTS § 114.11 Storage and handling. Biological products at licensed establishments shall be protected at all times against improper storage and handling. Completed product shall be kept under...

9 CFR 114.11 - Storage and handling.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 9 Animals and Animal Products 1 2013-01-01 2013-01-01 false Storage and handling. 114.11 Section... BIOLOGICAL PRODUCTS § 114.11 Storage and handling. Biological products at licensed establishments shall be protected at all times against improper storage and handling. Completed product shall be kept under...

14 CFR 25.489 - Ground handling conditions.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Ground handling conditions. 25.489 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Ground Loads § 25.489 Ground handling conditions... ground handling conditions). No wing lift may be considered. The shock absorbers and tires may be assumed...

14 CFR 25.489 - Ground handling conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Ground handling conditions. 25.489 Section... AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Ground Loads § 25.489 Ground handling conditions... ground handling conditions). No wing lift may be considered. The shock absorbers and tires may be assumed...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 7 Agriculture 8 2012-01-01 2012-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 7 Agriculture 8 2013-01-01 2013-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (MARKETING AGREEMENTS... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 7 Agriculture 8 2011-01-01 2011-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

7 CFR 981.42 - Quality control.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Quality control. 981.42 Section 981.42 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing Agreements... Regulating Handling Quality Control § 981.42 Quality control. (a) Incoming. Except as provided in this...

Llama handling and training.

PubMed

McGee, M

1994-07-01

This article offers insights into the relationship of llama owners to their animals and the role of veterinarians as part of the animal care team. The effect of human behavior and handling techniques on llama behavior and marketability are discussed. Progressive ideas for nonforceful llama handling equipment, procedures, and training ideas are outlined in detail. Included are specific training plans for routine herd management chores such as injections and toenail trimming. This article is useful for both veterinarians and llama owners.

Automatic sequential fluid handling with multilayer microfluidic sample isolated pumping

PubMed Central

Liu, Jixiao; Fu, Hai; Yang, Tianhang; Li, Songjing

2015-01-01

To sequentially handle fluids is of great significance in quantitative biology, analytical chemistry, and bioassays. However, the technological options are limited when building such microfluidic sequential processing systems, and one of the encountered challenges is the need for reliable, efficient, and mass-production available microfluidic pumping methods. Herein, we present a bubble-free and pumping-control unified liquid handling method that is compatible with large-scale manufacture, termed multilayer microfluidic sample isolated pumping (mμSIP). The core part of the mμSIP is the selective permeable membrane that isolates the fluidic layer from the pneumatic layer. The air diffusion from the fluidic channel network into the degassing pneumatic channel network leads to fluidic channel pressure variation, which further results in consistent bubble-free liquid pumping into the channels and the dead-end chambers. We characterize the mμSIP by comparing the fluidic actuation processes with different parameters and a flow rate range of 0.013 μl/s to 0.097 μl/s is observed in the experiments. As the proof of concept, we demonstrate an automatic sequential fluid handling system aiming at digital assays and immunoassays, which further proves the unified pumping-control and suggests that the mμSIP is suitable for functional microfluidic assays with minimal operations. We believe that the mμSIP technology and demonstrated automatic sequential fluid handling system would enrich the microfluidic toolbox and benefit further inventions. PMID:26487904

The impact of drywall handling tools on the low back.

PubMed

Hess, Jennifer A; Kincl, Laurel D; Davis, Kermit

2010-03-01

Carpenters and other construction workers who install drywall have high rates of strains and sprains to the low back and shoulder. Drywall is heavy and awkward to handle resulting in increased risk of injury. The purpose of this study was to evaluate several low-cost coupling tools that have the potential to reduce awkward postures in drywall installers. Five coupling tools were evaluated using the Lumbar Motion Monitor that measures trunk kinematics and predicts probability of low back disorder group membership risk (LBD risk). Workers answered surveys about their comfort while using each tool. The results indicate that use of the 2-person manual lift and the J-handle provide the best reduction in awkward postures, motions, low back sagittal moment, and LBD risk. The two-person manual lift appears to be the safest method of lifting and moving drywall, though using the two-person J-handle also significantly reduces injury risk. Given that carpenters are skeptical about using equipment that can get in the way or get lost, a practical recommendation is promotion of two-person manual lifting. For single-person lifts, the Old Man tool is a viable option to decrease risk of MSDs.

A study to identify research issues in the area of electromagnetic measurements and signal handling of remotely sensed data

NASA Technical Reports Server (NTRS)

1982-01-01

Research issues in the area of electromagnetic measurements and signal handling of remotely sensed data are identified. The following seven issues are discussed; platform/sensor system position and velocity, platform/sensor attitudes and attitude rates, optics and antennas, detectors and associated electronics, sensor calibration, signal handling, and system design.

Human-animal interactions and safety during dairy cattle handling--Comparing moving cows to milking and hoof trimming.

PubMed

Lindahl, C; Pinzke, S; Herlin, A; Keeling, L J

2016-03-01

Cattle handling is a dangerous activity on dairy farms, and cows are a major cause of injuries to livestock handlers. Even if dairy cows are generally tranquil and docile, when situations occur that they perceive or remember as aversive, they may become agitated and hazardous to handle. This study aimed to compare human-animal interactions, cow behavior, and handler safety when moving cows to daily milking and moving cows to more rarely occurring and possibly aversive hoof trimming. These processes were observed on 12 Swedish commercial dairy farms. The study included behavioral observations of handler and cows and cow heart rate recordings, as well as recording frequencies of situations and incidents related to an increased injury risk to the handler. At milking, cows were quite easily moved using few interactions. As expected, the cows showed no behavioral signs of stress, fear, or resistance and their heart rate only rose slightly from the baseline (i.e., the average heart rate during an undisturbed period before handling). Moving cows to hoof trimming involved more forceful and gentle interactions compared with moving cows to milking. Furthermore, the cows showed much higher frequencies of behaviors indicative of aversion and fear (e.g., freezing, balking, and resistance), as well as a higher increase in heart rate. The risk of injury to which handlers were exposed also increased when moving cows to hoof trimming rather than to routine milking. Some interactions (such as forceful tactile interactions with an object and pulling a neck strap or halter) appeared to be related to potentially dangerous incidents where the handler was being kicked, head-butted, or run over by a cow. In conclusion, moving cows to hoof trimming resulted in higher frequencies of behaviors indicating fear, more forceful interactions, and increased injury risks to the handler than moving cows to milking. Improving potentially stressful handling procedures (e.g., by better animal handling

14 CFR 158.49 - Handling of PFC's.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Handling of PFC's. 158.49 Section 158.49... PASSENGER FACILITY CHARGES (PFC'S) Collection, Handling, and Remittance of PFC's § 158.49 Handling of PFC's... amount of PFC revenue in the covered air carrier's account at the time the bankruptcy petition is filed...

14 CFR 158.49 - Handling of PFC's.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Handling of PFC's. 158.49 Section 158.49... PASSENGER FACILITY CHARGES (PFC'S) Collection, Handling, and Remittance of PFC's § 158.49 Handling of PFC's... amount of PFC revenue in the covered air carrier's account at the time the bankruptcy petition is filed...

14 CFR 158.49 - Handling of PFC's.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Handling of PFC's. 158.49 Section 158.49... PASSENGER FACILITY CHARGES (PFC'S) Collection, Handling, and Remittance of PFC's § 158.49 Handling of PFC's... amount of PFC revenue in the covered air carrier's account at the time the bankruptcy petition is filed...

14 CFR 158.49 - Handling of PFC's.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Handling of PFC's. 158.49 Section 158.49... PASSENGER FACILITY CHARGES (PFC'S) Collection, Handling, and Remittance of PFC's § 158.49 Handling of PFC's... amount of PFC revenue in the covered air carrier's account at the time the bankruptcy petition is filed...

14 CFR 158.49 - Handling of PFC's.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Handling of PFC's. 158.49 Section 158.49... PASSENGER FACILITY CHARGES (PFC'S) Collection, Handling, and Remittance of PFC's § 158.49 Handling of PFC's... amount of PFC revenue in the covered air carrier's account at the time the bankruptcy petition is filed...

A cross-sectional study assessing the association between online ratings and structural and quality of care measures: results from two German physician rating websites.

PubMed

Emmert, Martin; Adelhardt, Thomas; Sander, Uwe; Wambach, Veit; Lindenthal, Jörg

2015-09-24

Even though physician rating websites (PRWs) have been gaining in importance in both practice and research, little evidence is available on the association of patients' online ratings with the quality of care of physicians. It thus remains unclear whether patients should rely on these ratings when selecting a physician. The objective of this study was to measure the association between online ratings and structural and quality of care measures for 65 physician practices from the German Integrated Health Care Network "Quality and Efficiency" (QuE). Online reviews from two German PRWs were included which covered a three-year period (2011 to 2013) and included 1179 and 991 ratings, respectively. Information for 65 QuE practices was obtained for the year 2012 and included 21 measures related to structural information (N = 6), process quality (N = 10), intermediate outcomes (N = 2), patient satisfaction (N = 1), and costs (N = 2). The Spearman rank coefficient of correlation was applied to measure the association between ratings and practice-related information. Patient satisfaction results from offline surveys and the patients per doctor ratio in a practice were shown to be significantly associated with online ratings on both PRWs. For one PRW, additional significant associations could be shown between online ratings and cost-related measures for medication, preventative examinations, and one diabetes type 2-related intermediate outcome measure. There again, results from the second PRW showed significant associations with the age of the physicians and the number of patients per practice, four process-related quality measures for diabetes type 2 and asthma, and one cost-related measure for medication. Several significant associations were found which varied between the PRWs. Patients interested in the satisfaction of other patients with a physician might select a physician on the basis of online ratings. Even though our results indicate associations

Notes From the Field: Direct Observation Versus Rating by Videos for the Assessment of Central Venous Catheterization Skills.

PubMed

Ma, Irene W Y; Zalunardo, Nadia; Brindle, Mary E; Hatala, Rose; McLaughlin, Kevin

2015-09-01

Blinded assessments of technical skills using video-recordings may offer more objective assessments than direct observations. This study seeks to compare these two modalities. Two trained assessors independently assessed 18 central venous catheterization performances by direct observation and video-recorded assessments using two tools. Although sound quality was deemed adequate in all videos, portions of the video for wire handling and drape handling were frequently out of view (n = 13, 72% for wire-handling; n = 17, 94% for drape-handling). There were no differences in summary global rating scores, checklist scores, or pass/fail decisions for either modality (p > 0.05). Inter-rater reliability was acceptable for both modalities. Of the 26 discrepancies identified between direct observation and video-recorded assessments, three discrepancies (12%) were due to inattention during video review, while one (4%) discrepancy was due to inattention during direct observation. In conclusion, although scores did not differ between the two assessment modalities, techniques of video-recording may significantly impact individual items of assessments. © The Author(s) 2014.

Closed-system drug-transfer devices plus safe handling of hazardous drugs versus safe handling alone for reducing exposure to infusional hazardous drugs in healthcare staff.

PubMed

Gurusamy, Kurinchi Selvan; Best, Lawrence Mj; Tanguay, Cynthia; Lennan, Elaine; Korva, Mika; Bussières, Jean-François

2018-03-27

Occupational exposure to hazardous drugs can decrease fertility and result in miscarriages, stillbirths, and cancers in healthcare staff. Several recommended practices aim to reduce this exposure, including protective clothing, gloves, and biological safety cabinets ('safe handling'). There is significant uncertainty as to whether using closed-system drug-transfer devices (CSTD) in addition to safe handling decreases the contamination and risk of staff exposure to infusional hazardous drugs compared to safe handling alone. To assess the effects of closed-system drug-transfer of infusional hazardous drugs plus safe handling versus safe handling alone for reducing staff exposure to infusional hazardous drugs and risk of staff contamination. We searched the Cochrane Central Register of Controlled Trials (CENTRAL), MEDLINE, Embase, OSH-UPDATE, CINAHL, Science Citation Index Expanded, economic evaluation databases, the World Health Organization International Clinical Trials Registry Platform, and ClinicalTrials.gov to October 2017. We included comparative studies of any study design (irrespective of language, blinding, or publication status) that compared CSTD plus safe handling versus safe handling alone for infusional hazardous drugs. Two review authors independently identified trials and extracted data. We calculated the risk ratio (RR) and mean difference (MD) with 95% confidence intervals (CI) using both fixed-effect and random-effects models. We assessed risk of bias according to the risk of bias in non-randomised studies of interventions (ROBINS-I) tool, used an intracluster correlation coefficient of 0.10, and we assessed the quality of the evidence using GRADE. We included 23 observational cluster studies (358 hospitals) in this review. We did not find any randomised controlled trials or formal economic evaluations. In 21 studies, the people who used the intervention (CSTD plus safe handling) and control (safe handling alone) were pharmacists or pharmacy

Mooring and ground handling rigid airships

NASA Technical Reports Server (NTRS)

Walker, H., Jr.

1975-01-01

The problems of mooring and ground handling rigid airships are discussed. A brief history of Mooring and Ground Handling Rigid Airships from July 2, 1900 through September 1, 1939 is included. Also a brief history of ground handling developments with large U. S. Navy nonrigid airships between September 1, 1939 and August 31, 1962 is included wherein developed equipment and techniques appear applicable to future large rigid airships. Finally recommendations are made pertaining to equipment and procedures which appear desirable and feasible for future rigid airship programs.

Flying-qualities criteria for wings-level-turn maneuvering during an air-to-ground weapon delivery task

NASA Technical Reports Server (NTRS)

Sammonds, R. I.; Bunnell, J. W.

1981-01-01

A moving base simulator experiment demonstrated that a wings-level-turn control mode improved flying qualities for air to ground weapon delivery compared with those of a conventionally controlled aircraft. Evaluations of criteria for dynamic response for this system have shown that pilot ratings correlate well on the basis of equivalent time constant of the initial response. Ranges of this time constant, as well as digital system transport delays and lateral acceleration control authorities that encompassed level 1 through 3 handling qualities, were determined.

Effect of handling characteristics on minimum time cornering with torque vectoring

NASA Astrophysics Data System (ADS)

Smith, E. N.; Velenis, E.; Tavernini, D.; Cao, D.

2018-02-01

In this paper, the effect of both passive and actively-modified vehicle handling characteristics on minimum time manoeuvring for vehicles with 4-wheel torque vectoring (TV) capability is studied. First, a baseline optimal TV strategy is sought, independent of any causal control law. An optimal control problem (OCP) is initially formulated considering 4 independent wheel torque inputs, together with the steering angle rate, as the control variables. Using this formulation, the performance benefit using TV against an electric drive train with a fixed torque distribution, is demonstrated. The sensitivity of TV-controlled manoeuvre time to the passive understeer gradient of the vehicle is then studied. A second formulation of the OCP is introduced where a closed-loop TV controller is incorporated into the system dynamics of the OCP. This formulation allows the effect of actively modifying a vehicle's handling characteristic via TV on its minimum time cornering performance of the vehicle to be assessed. In particular, the effect of the target understeer gradient as the key tuning parameter of the literature-standard steady-state linear single-track model yaw rate reference is analysed.

IMPROVING BIOMASS LOGISTICS COST WITHIN AGRONOMIC SUSTAINABILITY CONSTRAINTS AND BIOMASS QUALITY TARGETS

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. Richard Hess; Kevin L. Kenney; Christopher T. Wright

Equipment manufacturers have made rapid improvements in biomass harvesting and handling equipment. These improvements have increased transportation and handling efficiencies due to higher biomass densities and reduced losses. Improvements in grinder efficiencies and capacity have reduced biomass grinding costs. Biomass collection efficiencies (the ratio of biomass collected to the amount available in the field) as high as 75% for crop residues and greater than 90% for perennial energy crops have also been demonstrated. However, as collection rates increase, the fraction of entrained soil in the biomass increases, and high biomass residue removal rates can violate agronomic sustainability limits. Advancements inmore » quantifying multi-factor sustainability limits to increase removal rate as guided by sustainable residue removal plans, and mitigating soil contamination through targeted removal rates based on soil type and residue type/fraction is allowing the use of new high efficiency harvesting equipment and methods. As another consideration, single pass harvesting and other technologies that improve harvesting costs cause biomass storage moisture management challenges, which challenges are further perturbed by annual variability in biomass moisture content. Monitoring, sampling, simulation, and analysis provide basis for moisture, time, and quality relationships in storage, which has allowed the development of moisture tolerant storage systems and best management processes that combine moisture content and time to accommodate baled storage of wet material based upon “shelf-life.” The key to improving biomass supply logistics costs has been developing the associated agronomic sustainability and biomass quality technologies and processes that allow the implementation of equipment engineering solutions.« less

Exploring individual quality: Basal metabolic rate and reproductive performance in storm-petrels

USGS Publications Warehouse

Blackmer, A.L.; Mauck, R.A.; Ackerman, Joshua T.; Huntington, C.E.; Nevitt, G.A.; Williams, J.B.

2005-01-01

Despite evidence that some individuals achieve both superior reproductive performance and high survivorship, the factors underlying variation in individual quality are not well understood. The compensation and increased-intake hypotheses predict that basal metabolic rate (BMR) influences reproductive performance; if so, variation in BMR may be related to differences in individual quality. We evaluated whether BMR measured during the incubation period provides a proximate explanation for variation in individual quality by measuring the BMRs and reproductive performance of Leach's storm-petrels (Oceanodroma leucorhoa) breeding on Kent Island, New Brunswick, Canada, during 2000 and 2001. We statistically controlled for internal (body mass, breeding age, sex) and external (year, date, time of day) effects on BMR. We found that males with relatively low BMRs hatched their eggs earlier in the season and that their chicks' wing growth rates were faster compared to males with relatively high BMRs. Conversely, BMR was not related to egg volume, hatching date, or chick growth rate for females or to lifetime (???23 years) hatching success for either sex. Thus, for males but not for females, our results support the compensation hypothesis. This hypothesis predicts that animals with low BMRs will achieve better reproductive performance than animals with high BMRs because they have lower self-maintenance costs and therefore can apportion more energy to reproduction. These results provide evidence that intraspecific variation in reproductive performance is related to BMR and suggest that BMR may influence individual quality in males. ?? The Author 2005. Published by Oxford University Press on behalf of the International Society for Behavioral Ecology. All rights reserved.

Ergonomics: safe patient handling and mobility.

PubMed

Hallmark, Beth; Mechan, Patricia; Shores, Lynne

2015-03-01

This article reviews and investigates the issues surrounding ergonomics, with a specific focus on safe patient handling and mobility. The health care worker of today faces many challenges, one of which is related to the safety of patients. Safe patient handling and mobility is on the forefront of the movement to improve patient safety. This article reviews the risks associated with patient handling and mobility, and informs the reader of current evidence-based practice relevant to this area of care. Copyright © 2015 Elsevier Inc. All rights reserved.

The Influence of Race/Ethnicity and Education on Family Ratings of the Quality of Dying in the ICU.

PubMed

Lee, Janet J; Long, Ann C; Curtis, J Randall; Engelberg, Ruth A

2016-01-01

Racial and ethnic differences in end-of-life care may be attributable to both patient preferences and health-care disparities. Identifying factors that differentiate preferences from disparities may enhance end-of-life care for critically ill patients and their families. To understand the association of minority race/ethnicity and education with family ratings of the quality of dying and death, taking into consideration possible markers of patient and family preferences for end-of-life care as mediators of this association. Data were obtained from 15 intensive care units participating in a cluster-randomized trial of a palliative care intervention. Family members of decedents completed self-report surveys evaluating quality of dying. We used regression analyses to identify associations between race/ethnicity, education, and quality of dying ratings. We then used path analyses to investigate whether advance directives and life-sustaining treatment acted as mediators between patient characteristics and ratings of quality of dying. Family members returned 1290 surveys for 2850 decedents. Patient and family minority race/ethnicity were both associated with lower ratings of quality of dying. Presence of a living will and dying in the setting of full support mediated the relationship between patient race and family ratings; patient race exerted an indirect, rather than direct, effect on quality of dying. Family minority race had a direct effect on lower ratings of quality of dying. Neither patient nor family education was associated with quality of dying. Minority race/ethnicity was associated with lower family ratings of quality of dying. This association was mediated by factors that may be markers of patient and family preferences (living will, death in the setting of full support); family member minority race/ethnicity was directly associated with lower ratings of quality of dying. Our findings generate hypothesized pathways that require future evaluation. Copyright �

Exception handling for sensor fusion

NASA Astrophysics Data System (ADS)

Chavez, G. T.; Murphy, Robin R.

1993-08-01

This paper presents a control scheme for handling sensing failures (sensor malfunctions, significant degradations in performance due to changes in the environment, and errant expectations) in sensor fusion for autonomous mobile robots. The advantages of the exception handling mechanism are that it emphasizes a fast response to sensing failures, is able to use only a partial causal model of sensing failure, and leads to a graceful degradation of sensing if the sensing failure cannot be compensated for. The exception handling mechanism consists of two modules: error classification and error recovery. The error classification module in the exception handler attempts to classify the type and source(s) of the error using a modified generate-and-test procedure. If the source of the error is isolated, the error recovery module examines its cache of recovery schemes, which either repair or replace the current sensing configuration. If the failure is due to an error in expectation or cannot be identified, the planner is alerted. Experiments using actual sensor data collected by the CSM Mobile Robotics/Machine Perception Laboratory's Denning mobile robot demonstrate the operation of the exception handling mechanism.

Positive and negative gestational handling influences placental traits and mother-offspring behavior in dairy goats.

PubMed

Baxter, Emma M; Mulligan, Johan; Hall, Sarah A; Donbavand, Jo E; Palme, Rupert; Aldujaili, Emad; Zanella, Adroaldo J; Dwyer, Cathy M

2016-04-01

Dairy animals are subjected to a number of potential stressors throughout their lives, including daily interactions with humans. The quality of these interactions may have direct consequences for the animal undergoing the experience, but if such events occur during gestation it may also affect the developing fetus. This study examined the effects of differential handling during mid-gestation in 40 twin-bearing Saanen×Toggenburg primiparous goats. Between days 80 and 115 of gestation (gestation=150 days), goats were subjected to aversive (AVS, n=13), gentle (GEN, n=13) or minimal (M, n=14) handling protocols for 10 minute periods twice daily. The control (M) group did not receive handling treatments and all goats received normal husbandry procedures outside treatment periods. Salivary cortisol measured during the treatment period was higher in AVS goats (mean cortisol (sem) in pg/μl: AVS: 176.7 (18.2), GEN: 119.6 (11.1), M: 126.5 (13.7); P=0.007). Data collection was focussed on mother-offspring behaviors 2h post-partum, placental morphology and colostrum quality. AVS goats were the only treatment group to suffer fetal loss (16% loss vs 0% in GEN and M, P=0.05). Treatment also influenced placental morphology with a tendency for fewer cotyledons evident in placentae from the aversive treatment (AVS: 87.9 (7.8), GEN: 107.1 (7.9), M: 112.1 (9.3), P=0.093), and significantly fewer medium sized cotyledons (AVS: 67.6 (7.8), GEN: 89.3 (6.4), M: 84.3 (5.4), P=0.042). GEN goats displayed more grooming and nosing behaviors towards their young during the first 2h post-partum (grooming: GEN: 89.3% (7.1), AVS: 72.6% (7.7), M: 63.4% (9.0), P=0.045; nosing frequency: GEN: 58.8 (12.5), AVS: 28.6 (11.1), M: 34.7 (6.5), P=0.021). There was an overall trend for kids from mothers experiencing the AVS treatment to take longer to stand, reach the udder and suck compared to kids from GEN and M treatment groups. Treatment significantly affected latency to perform play behavior, with kids

Analysis of Material Handling Safety in Construction Sites and Countermeasures for Effective Enhancement

PubMed Central

Anil Kumar, C. N.; Sakthivel, M.; Elangovan, R. K.; Arularasu, M.

2015-01-01

One of many hazardous workplaces includes the construction sites as they involve several dangerous tasks. Many studies have revealed that material handling equipment is a major cause of accidents at these sites. Though safety measures are being followed and monitored continuously, accident rates are still high as either workers are unaware of hazards or the safety regulations are not being strictly followed. This paper analyses the safety management systems at construction sites through means of questionnaire surveys with employees, specifically referring to safety of material handling equipment. Based on results of the questionnaire surveys, two construction sites were selected for a safety education program targeting worker safety related to material handling equipment. Knowledge levels of the workers were gathered before and after the program and results obtained were subjected to a t-test analysis to mark significance level of the conducted safety education program. PMID:26446572

Examining the Relationship Between Perceived Quality of Care and Actual Quality of Care as Measured by 30-Day Readmission Rates.

PubMed

Salinas, Stanley R

To test the relationship between patient experience, as measured by the Hospital Consumer Assessment of Healthcare Providers and Systems (HCAHPS), and actual quality of care, as measured by 30-day readmission rates. Both HCAHPS data and outcome data reported to the Centers of Medicare & Medicaid Services (CMS). This secondary, nationwide (N = 4060), hospital-level study focused only on acute care hospitals. HCAHPS question 22 "Would you recommend this hospital to your friends and family?" was used to determine level of overall satisfaction, and 30-day readmission rates, as reported to the CMS, was used as a proxy for actual quality of care. A statistically significant relationship was found between patient experience and actual quality outcomes. The results of this study reinforce the inclusion of patient experience in Medicare's Value Based Purchasing program as a matter of good public policy.

Physiotherapist agreement when visually rating movement quality during lower extremity functional screening tests.

PubMed

Whatman, Chris; Hing, Wayne; Hume, Patria

2012-05-01

To investigate physiotherapist agreement in rating movement quality during lower extremity functional tests using two visual rating methods and physiotherapists with differing clinical experience. Clinical measurement. Six healthy individuals were rated by 44 physiotherapists. These raters were in three groups (inexperienced, novice, experienced). Video recordings of all six individuals performing four lower extremity functional tests were visually rated (dichotomous or ordinal scale) using two rating methods (overall or segment) on two occasions separated by 3-4 weeks. Intra and inter-rater agreement for physiotherapists was determined using overall percentage agreement (OPA) and the first order agreement coefficient (AC1). Intra-rater agreement for overall and segment methods ranged from slight to almost perfect (OPA: 29-96%, AC1: 0.01 to 0.96). AC1 agreement was better in the experienced group (84-99% likelihood) and for dichotomous rating (97-100% likelihood). Inter-rater agreement ranged from fair to good (OPA: 45-79%; AC1: 0.22-0.71). AC1 agreement was not influenced by clinical experience but was again better using dichotomous rating. Physiotherapists' visual rating of movement quality during lower extremity functional tests resulted in slight to almost perfect intra-rater agreement and fair to good inter-rater agreement. Agreement improved with increased level of clinical experience and use of dichotomous rating. Copyright © 2011 Elsevier Ltd. All rights reserved.

Method and system rapid piece handling

DOEpatents

Spletzer, Barry L.

1996-01-01

The advent of high-speed fabric cutters has made necessary the development of automated techniques for the collection and sorting of garment pieces into collated piles of pieces ready for assembly. The present invention enables a new method for such handling and sorting of garment parts, and to apparatus capable of carrying out this new method. The common thread is the application of computer-controlled shuttling bins, capable of picking up a desired piece of fabric and dropping it in collated order for assembly. Such apparatus with appropriate computer control relieves the bottleneck now presented by the sorting and collation procedure, thus greatly increasing the overall rate at which garments can be assembled.

Hazardous Waste Certification Plan: Hazardous Waste Handling Facility, Lawrence Berkeley Laboratory

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1992-02-01

The purpose of this plan is to describe the organization and methodology for the certification of hazardous waste (HW) handled in the Lawrence Berkeley Laboratory (LBL) Hazardous Waste Handling Facility (HWHF). The plan also incorporates the applicable elements of waste reduction, which include both up-front minimization and end- product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; and executive summary of the Quality Assurance Program Plan (QAPP) for the HWHF and a list of the current and planned implementing procedures used in waste certification. The plan provides guidance frommore » the HWHF to waste generators, waste handlers, and the Systems Group Manager to enable them to conduct their activities and carry out their responsibilities in a manner that complies with several requirements of the Federal Resource Conservation and Resource Recovery Act (RCRA), the Federal Department of Transportation (DOT), and the State of California, Code of Regulations (CCR), Title 22.« less

Flame quality monitor system for fixed firing rate oil burners

DOEpatents

Butcher, Thomas A.; Cerniglia, Philip

1992-01-01

A method and apparatus for determining and indicating the flame quality, or efficiency of the air-fuel ratio, in a fixed firing rate heating unit, such as an oil burning furnace, is provided. When the flame brightness falls outside a preset range, the flame quality, or excess air, has changed to the point that the unit should be serviced. The flame quality indicator output is in the form of lights mounted on the front of the unit. A green light indicates that the flame is about in the same condition as when the burner was last serviced. A red light indicates a flame which is either too rich or too lean, and that servicing of the burner is required. At the end of each firing cycle, the flame quality indicator goes into a hold mode which is in effect during the period that the burner remains off. A yellow or amber light indicates that the burner is in the hold mode. In this mode, the flame quality lights indicate the flame condition immediately before the burner turned off. Thus the unit can be viewed when it is off, and the flame condition at the end of the previous firing cycle can be observed.

Do the stars align? Distribution of high-quality ratings of healthcare sectors across US markets.

PubMed

Figueroa, Jose; Feyman, Yevgeniy; Blumenthal, Daniel; Jha, Ashish

2018-04-01

The US government created five-star rating systems to evaluate hospital, nursing homes, home health agency and dialysis centre quality. The degree to which quality is a property of organisations versus geographical markets is unclear. To determine whether high-quality healthcare service sectors are clustered within US healthcare markets. Using data from the Centers for Medicare and Medicaid Services' Hospital, Dialysis, Nursing Home and Home Health Compare databases, we calculated the mean star ratings of four healthcare sectors in 304 US hospital referral regions (HRRs). For each sector, we ranked HRRs into terciles by mean star rating. Within each HRR, we assessed concordance of tercile rank across sectors using a multirater kappa. Using t-tests, we compared characteristics of HRRs with three to four top-ranked sectors, one to two top-ranked sectors and zero top-ranked sectors. Six HRRs (2.0% of HRRs) had four top-ranked healthcare sectors, 38 (12.5%) had three top-ranked health sectors, 71 (23.4%) had two top-ranked sectors, 111 (36.5%) had one top-ranked sector and 78 (25.7%) HRRs had no top-ranked sectors. A multirater kappa across all sectors showed poor to slight agreement (K=0.055). Compared with HRRs with zero top-ranked sectors, those with three to four top-ranked sectors had higher median incomes, fewer black residents, lower mortality rates and were less impoverished. Results were similar for HRRs with one to two top-ranked sectors. Few US healthcare markets exhibit high-quality performance across four distinct healthcare service sectors, suggesting that high-quality care in one sector may not be dependent on or improve care quality in other sectors. Policies that promote accountability for quality across sectors (eg, bundled payments and shared quality metrics) may be needed to systematically improve quality across sectors. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No

Manipulation of follicle development to ensure optimal oocyte quality and conception rates in cattle.