Modeling of Wave Propagation in the Osaka Sedimentary Basin during the 2013 Awaji Island Earthquake (Mw5.8)

NASA Astrophysics Data System (ADS)

Asano, K.; Sekiguchi, H.; Iwata, T.; Yoshimi, M.; Hayashida, T.; Saomoto, H.; Horikawa, H.

2013-12-01

The three-dimensional velocity structure model for the Osaka sedimentary basin, southwest Japan is developed and improved based on many kinds of geophysical explorations for decades (e.g., Kagawa et al., 1993; Horikawa et al., 2003; Iwata et al., 2008). Recently, our project (Sekiguchi et al., 2013) developed a new three-dimensional velocity model for strong motion prediction of the Uemachi fault earthquake in the Osaka basin considering both geophysical and geological information by adding newly obtained exploration data such as reflection surveys, microtremor surveys, and receiver function analysis (hereafter we call UMC2013 model) . On April 13, 2013, an inland earthquake of Mw5.8 occurred in Awaji Island, which is close to the southwestern boundary of the aftershock area of the 1995 Kobe earthquake. The strong ground motions are densely observed at more than 100 stations in the basin. The ground motion lasted longer than four minutes in the Osaka urban area where its bedrock depth is about 1-2 km. This long-duration ground motions are mainly due to the surface waves excited in this sedimentary basin whereas the magnitude of this earthquake is moderate and the rupture duration is expected to be less than 5 s. In this study, we modeled long-period (more than 2s) ground motions during this earthquake to check the performance of the present UMC2013 model and to obtain a better constraint on the attenuation factor of sedimentary part of the basin. The seismic wave propagation in the region including the source and the Osaka basin is modeled by the finite difference method using the staggered grid solving the elasto-dynamic equations. The domain of 90km×85km×25.5km is modeled and discretized with a grid spacing of 50 m. Since the minimum S-wave velocity of the UMC2013 model is about 250 m/s, this calculation is valid up to the period of about 1 s. The effect of attenuation is included in the form of Q(f)=Q0(T0/T) proposed by Graves (1996). A PML is implemented in

Thermoluminescence of quartz collected from Nojima Fault Trench excavated in 2015

NASA Astrophysics Data System (ADS)

Hasebe, N.; Miura, K.; Ganzawa, Y.; Tagami, T.; Lin, A.

2017-12-01

The Southern Hyogo prefecture earthquake occurred in 1995, which is known as Kobe Earthquake or Great Hanshin-Awaji Earthquake, was caused by the activity of the Nojima fault.　The research project on the Nojima fault is currently going on and new trench was excavated in 2015. We investigate the effect of fault activity on surrounding rocks by thermoluminescence (TL) dating method. First, quartz were extracted from samples collected from the trench wall with different distance from the fault. A block of nearby basement rock is also collected and analyzed. Next, the luminescence sites and their emission temperatures were determined by T-Tmax method (McKeever, 1980) perfomed by 10 ° C interval for selected samples (the basement rock collected from Rokko granite, the granite sample collected about 5 m away from the fault in the trench, and the gouge sample adjacent to the fault). As a result, the peak emission temperatures were 200-220 ° C, 270 ° C and 320-350 ° C for granite quartz. These values were concordant for UV-TL and Blue TL. The activation energy and frequency factors were determined for signals emitted at different temperatures by peak shift methods (Aitken, 1985). On the other hand, the TL emission curves for the sample adjacent to the fault do not show discrete luminescence sites, different from granite samples. Natural TL emission show variety of TL profile. The accumulated doses of each sample were estimated for identified signal peaks after peak separation. Signals from different peak temperatures show different dose values in all the samples. The dose estimated by signals at 200 ° showed the minimum value for all samples. The same sample show different accumulated dose for Blue TL and UV-TL. The variety of accumulated doses in a sample may be reflective of complex thermal history of samples, and/or partly caused by the ineffective peak separation. Even the host rock collected away from the fault show a low accumulated dose in 200°C singnal, far

Akashi Kaikyo Bridge, Japan

NASA Image and Video Library

2013-03-25

NASA Terra spacecraft shows the Akashi Kaikyo Bridge or Pearl Bridge, the longest central span of any suspension bridge in the world, at 1991 meters, connecting the city of Kobe, Japan with Iwaja on Awaji Island by crossing the busy Akashi Strait.

PREFACE: 14th International Conference on Micro and Nanotechnology for Power Generation and Energy Conversion Applications (PowerMEMS 2014)

NASA Astrophysics Data System (ADS)

2014-11-01

It is our great pleasure to welcome you to the 14th International Conference on Micro- and Nano-Technology for Power Generation and Energy Conversion Applications, or PowerMEMS 2014, in Awaji Island, Japan. The aim of PowerMEM is to present the latest research results in the field of miniature, micro- and nano-scale technologies for power generation and energy conversion. The conference will also- give us the opportunity to exchange informations and new ideas in the field of Power MEMS/NEMS. The current status of the field of PowerMEMS spans the full spectrum from basic research to practical applications. We will enjoy valuable discussions not only from the viewpoint of academia but from commercial and industrial perspectives. In the conference, three invited speakers lead the technical program. We received 172 abstracts and after a careful reviewing process by the Technical Program Committee a total of 133 papers were selected for presentation. These have been organized into 16 Oral sessions in two parallel streams and two poster sessions including some late-news papers. The oral and regular poster papers are published by the Institute of Physics (IOP). We have also organized a PowerMEMS School in Kobe-Sannomiya contiguous to the main conference. This two-day school will cover various topics of energy harvesting. World leading experts will give invited lectures on their main topics. This is a new experiment to broaden the technology remit of our conference by organizing mini symposiums that aim to gather the latest research on the following topics by the organizers: Microscale Combustion, Wideband Vibration Energy Harvesting, RF Energy Transfer and Industrial Application. We hope this, and other activities will make PowerMEMS2014 a memorable success. One of the important programs in an international conference is the social program, and we prepare the PowerMEMS2014 banquet in the banquet room at the Westin Awaji Island Hotel. This will provide an opportunity to

The role of cranial and thoracic electromyography within diagnostic criteria for amyotrophic lateral sclerosis.

PubMed

Jenkins, Thomas M; Alix, James J P; Kandler, Rosalind H; Shaw, Pamela J; McDermott, Christopher J

2016-09-01

The contribution of cranial and thoracic region electromyography (EMG) to diagnostic criteria for amyotrophic lateral sclerosis (ALS) has not been evaluated. Clinical and EMG data from each craniospinal region were retrospectively assessed in 470 patients; 214 had ALS. Changes to diagnostic classification in Awaji-Shima and revised El Escorial criteria after withdrawal of cranial/thoracic EMG data were ascertained. Sensitivity for lower motor neuron involvement in ALS was highest in the cervical/lumbar regions; specificity was highest in cranial/thoracic regions. Cranial EMG contributed to definite/probable Awaji-Shima categorization in 1.4% of patients. Thoracic EMG made no contribution. For revised El Escorial criteria, cranial and thoracic data reclassified 1% and 5% of patients, respectively. Cranial EMG data make small contributions to both criteria, whereas thoracic data contribute only to the revised El Escorial criteria. However, cranial and thoracic region abnormalities are specific in ALS. Consideration should be given to allowing greater diagnostic contribution from thoracic EMG. Muscle Nerve 54: 378-385, 2016. © 2016 Wiley Periodicals, Inc.

Development of disaster pamphlets based on health needs of patients with chronic illnesses.

PubMed

Motoki, Emi; Mori, Kikuko; Kaji, Hidesuke; Nonami, Yoko; Fukano, Chika; Kayano, Tomonori; Kawada, Terue; Kimura, Yukari; Yasui, Kumiko; Ueki, Hiroko; Ugai, Kazuhiro

2010-01-01

The aim of this research was to develop a pamphlet that would enable patients with diabetes, rheumatic diseases, chronic respiratory disease, and dialysis treatment to be aware of changes in their physical conditions at an early stage of a disaster, cope with these changes, maintain self-care measures, and recover their health. Illness-specific pamphlets were produced based on disaster-related literature, news articles, surveys of victims of the Great Hanshin-Awaji Earthquake Disaster and Typhoon Tokage, and other sources. Each pamphlet consisted of seven sections-each section includes items common to all illnesses as well as items specific to each illness. The first section, "Physical Self-Care", contains a checklist of 18 common physical symptoms as well as symptoms specific to each illness, and goes on to explain what the symptoms may indicate and what should be done about them. The main aim of the "Changes in Mental Health Conditions" section is to detect posttraumatic stress disorder (PTSD) at an early stage. The section "Preventing the Deterioration of Chronic Illnesses" is designed to prevent the worsening of each illness through the provision of information on cold prevention, adjustment to the living environment, and ways of coping with stress. In the sections, "Medication Control" and "Importance of Having Medical Examinations", spaces are provided to list medications currently being used and details of the hospital address, in order to ensure the continued use of medications. The section, "Preparing for Evacuations" gives a list of everyday items and medical items needed to be prepared for a disaster. Finally, the "Methods of Contact in an Emergency" section provides details of how to use the voicemail service. The following content-specific to each illness also was explained in detail: (1) for diabetes, complications arising from the deterioration of the illness, attention to nutrition, and insulin management; (2) for rheumatic diseases, a checklist of

Akashi-Kaikyo Bridge, Japan

NASA Image and Video Library

2015-08-10

The Akashi Kaikyo Bridge in Japan has the longest central span of any suspension bridge in the world at 1991 m. The total length of the bridge is 3911 m. It links the city of Kobe on the mainland of Honshu to Iwaya on Awaji Island, crossing the busy Akashi Strait. The image was acquired April 26, 2014, covers an area of 8.1 by 11.2 km, and is located at 34.6 degrees north, 135 degrees east. http://photojournal.jpl.nasa.gov/catalog/PIA19747

An analysis of Japan Disaster Medical Assistance Team (J-DMAT) deployments in comparison with those of J-DMAT's counterpart in the United States (US-DMAT).

PubMed

Fuse, Akira; Yokota, Hiroyuki

2010-12-01

Lessons learned from the Great Hanshin-Awaji earthquake of 1995 underscored the necessity of establishing Disaster Medical Assistance Teams (DMATs) in Japan, and in 2005, the Japanese government's Central Disaster Prevention Council revised its Basic Disaster Management Plan to include full deployment of DMATs in disaster areas. Defining a DMAT as a trained, mobile, self-contained medical team that can act in the acute phase of a disaster (48 to 72 hours after its occurrence) to provide medical treatment in the devastated area, the revised plan called for the training of DMAT personnel for rapid deployment to any area of the country hit by a disaster. This paper presents descriptive data on the number and types of missions carried out by Japan DMAT (J-DMAT) in its first 5 years, and clarifies how J-DMAT differs from its counterpart in the United States (US-DMAT). The DMAT that the present authors belong to has been deployed for 2 natural disasters and 1 man-made disaster, and the operations carried out during these deployments are analyzed. Reports on J-DMAT activities published from 2004 through 2009 by the Japanese Association for Disaster Medicine are also included in the analysis. After training courses for J-DMAT personnel started in fiscal 2004, J-DMATs were deployed for 8 disasters in a period of 4 years. Five of these were natural disasters, and 3 man-made. Of the 5 natural disasters, 3 were earthquakes, and of the 3 man-made disasters, 2 were derailment accidents. Unlike in the United States, where hurricanes and floods account for the greatest number of DMAT deployments, earthquakes cause the largest number of disasters in Japan. Because Japan is small in comparison with the US (Japan has about 1/25 the land area of the US), most J-DMATs head for devastated areas by car from their respective hospitals. This is one reason why J-DMATs are smaller and more agile than US-DMATs. Another difference is that J-DMATs' activities following earthquakes involve

OCCUPATIONAL SAFETY AND HEALTH IN DISASTER RESTORATION ACTIVITY AFTER SOME MAJOR EARTHQUAKES

NASA Astrophysics Data System (ADS)

Toyosawa, Yasuo; Itoh, Kazuya; Kikkawa, Naotaka

Occupational safety and health in disaster restoration activity following the Great Hanshin Earthquake (1995), Niigata Chuetsu Earthquake (2004), Niigata Chuetsu-oki Earthquake (2007) Great East Japan Earthquake (2011) were analyzed and characterized in order to raise awareness on the risks and hazards in such work. In this scenario, the predominant type of accident is a "fall" which increases mainly due to the fact that labourers are working to repair houses and buildings. On the other hand, landslides were prevalent in the Niigata Chuetsu Earthquake, resulting in more accidents occurring during geotechnical works rather than in buildings construction works. In the abnormal conditions that characterize recovery activities, when safety and health measures have a tendency to be neglected, it is important to reinstate adequate measures as soon as possible by carrying out the usial risk assessments.

Progressive failure during the 1596 Keicho earthquakes on the Median Tectonic Line active fault zone, southwest Japan

NASA Astrophysics Data System (ADS)

Ikeda, M.; Toda, S.; Nishizaka, N.; Onishi, K.; Suzuki, S.

2015-12-01

Rupture patterns of a long fault system are controlled by spatial heterogeneity of fault strength and stress associated with geometrical characteristics and stress perturbation history. Mechanical process for sequential ruptures and multiple simultaneous ruptures, one of the characteristics of a long fault such as the North Anatolian fault, governs the size and frequency of large earthquakes. Here we introduce one of the cases in southwest Japan and explore what controls rupture initiation, sequential ruptures and fault branching on a long fault system. The Median Tectonic Line active fault zone　(hereinafter MTL) is the longest and most active fault in Japan. Based on historical accounts, a series of M ≥ 7 earthquakes occurred on at least a 300-km-long portion of the MTL in 1596. On September 1, the first event occurred on the Kawakami fault segment, in Central Shikoku, and the subsequent events occurred further west. Then on September 5, another rupture initiated from the Central to East Shikoku and then propagated toward the Rokko-Awaji fault zone to Kobe, a northern branch of the MTL, instead of the eastern main extent of the MTL. Another rupture eventually extended to near Kyoto. To reproduce this progressive failure, we applied two numerical models: one is a coulomb stress transfer; the other is a slip-tendency analysis under the tectonic stress. We found that Coulomb stress imparted from historical ruptures have triggered the subsequent ruptures nearby. However, stress transfer does not explain beginning of the sequence and rupture directivities. Instead, calculated slip-tendency values show highly variable along the MTL: high and low seismic potential in West and East Shikoku. The initiation point of the 1596 progressive failure locates near the boundary in the slip-tendency values. Furthermore, the slip-tendency on the Rokko-Awaji fault zone is far higher than that of the MTL in Wakayama, which may explain the rupture directivity toward Kobe-Kyoto.

Use of fault striations and dislocation models to infer tectonic shear stress during the 1995 Hyogo-Ken Nanbu (Kobe) earthquake

USGS Publications Warehouse

Spudich, P.; Guatteri, Mariagiovanna; Otsuki, K.; Minagawa, J.

1998-01-01

Dislocation models of the 1995 Hyogo-ken Nanbu (Kobe) earthquake derived by Yoshida et al. (1996) show substantial changes in direction of slip with time at specific points on the Nojima and Rokko fault systems, as do striations we observed on exposures of the Nojima fault surface on Awaji Island. Spudich (1992) showed that the initial stress, that is, the shear traction on the fault before the earthquake origin time, can be derived at points on the fault where the slip rake rotates with time if slip velocity and stress change are known at these points. From Yoshida's slip model, we calculated dynamic stress changes on the ruptured fault surfaces. To estimate errors, we compared the slip velocities and dynamic stress changes of several published models of the earthquake. The differences between these models had an exponential distribution, not gaussian. We developed a Bayesian method to estimate the probability density function (PDF) of initial stress from the striations and from Yoshida's slip model. Striations near Toshima and Hirabayashi give initial stresses of about 13 and 7 MPa, respectively. We obtained initial stresses of about 7 to 17 MPa at depths of 2 to 10 km on a subset of points on the Nojima and Rokko fault systems. Our initial stresses and coseismic stress changes agree well with postearthquake stresses measured by hydrofracturing in deep boreholes near Hirabayashi and Ogura on Awaji Island. Our results indicate that the Nojima fault slipped at very low shear stress, and fractional stress drop was complete near the surface and about 32% below depths of 2 km. Our results at depth depend on the accuracy of the rake rotations in Yoshida's model, which are probably correct on the Nojima fault but debatable on the Rokko fault. Our results imply that curved or cross-cutting fault striations can be formed in a single earthquake, contradicting a common assumption of structural geology.

STUDY ON SUPPORTING FOR DRAWING UP THE BCP FOR URBAN EXPRESSWAY NETWORK USING BY TRAFFIC SIMULATION SYSTEM

NASA Astrophysics Data System (ADS)

Yamawaki, Masashi; Shiraki, Wataru; Inomo, Hitoshi; Yasuda, Keiichi

The urban expressway network is an important infrastructure to execute a disaster restoration. Therefore, it is necessary to draw up the BCP (Business Continuity Plan) to enable securing of road user's safety and restoration of facilities, etc. It is important that each urban expressway manager execute decision and improvement of effective BCP countermeasures when disaster occurs by assuming various disaster situations. Then, in this study, we develop the traffic simulation system that can reproduce various disaster situations and traffic actions, and examine some methods supporting for drawing up the BCP for an urban expressway network. For disaster outside assumption such as tsunami generated by a huge earthquake, we examine some approaches securing safety of users and cars on the Hanshin Expressway Network as well as on general roads. And, we aim to propose a tsunami countermeasure not considered in the current urban expressway BCP.

Distal Predominance of Electrodiagnostic Abnormalities in Early Stage Amyotrophic Lateral Sclerosis.

PubMed

Shayya, Luay; Babu, Suma; Pioro, Erik P; Li, Jianbo; Li, Yuebing

2018-05-09

We compare the electrodiagnostic (EDX) yield of limb muscles in revealing lower motor neuron (LMN) dysfunction by electromyography (EMG) in early stage amyotrophic lateral sclerosis (ALS). Single-site retrospective review Results: This study includes 122 consecutive patients with possible ALS as defined by revised El Escorial Criteria. Distal limb muscles show more frequent EMG abnormalities than proximal muscles. EDX yield is higher in the limb where weakness begins and when clinical signs of LMN dysfunction are evident. Adoption of Awaji criteria increases the yield of EMG positive segments significantly in the cervical (p<0.0005) and lumbosacral regions (P<0.0001), and upgrades 19 patients into probable and 1 patient into definite categories. Electromyographic abnormalities are distal limb-predominant in early stage ALS. A redefinition of an EDX-positive cervical or lumbosacral segment, with an emphasis on distal limb muscles, may result in an earlier ALS diagnosis. This article is protected by copyright. All rights reserved. © 2018 Wiley Periodicals, Inc.

[Exposure to whole-body vibration of forklift truck operators in dockyards--actual exposure in Japan and evaluation by EN 13059].

PubMed

Tsujimura, Hiroji; Taoda, Kazushi; Nishiyama, Katsuo

2006-09-01

Low-back disorders are well documented as occupational hazards among forklift truck operators. The potential risk factors that may lead to low-back pain include exposure to whole-body vibration (WBV). In Europe, test methods were developed to evaluate WBV in industrial trucks, and the European Standard which defines the methods has been published. We measured the vibrations of forklift trucks operated in the Hanshin harbour area adopting procedures based on the CEN test and report the evaluation results. If the WBV magnitudes of the ride on forklift trucks in the workplace were less than or comparable to those in the CEN test, the CEN test could be considered useful for the risk assessment of forklift truck operators exposed to WBV. In order to verify the applicability of the CEN test to the evaluation of WBV exposure in the field, we conducted measurements of the WBV of four forklift trucks for 19 d. The trucks had already been examined by the CEN test. The truck velocity, driver position (sitting or not), and gear lever position were also measured, and video footage was obtained for the study. The results indicate that the vertical WBV magnitudes of the four forklift trucks were below the CEN test values. No dominant WBV direction was observed on any of the measurement days. The Health value (obtained by combining the values determined from the vibration in orthogonal coordinates) was comparable to that from the CEN test for one truck. The values for the other three trucks were lower. The data obtained for three forklift trucks were analyzed in each operating condition. The vertical WBV magnitudes and Health values for the three trucks were below the CEN test values when the trucks were travelling forwards with a load. The WBV in the anterior-posterior direction had the largest adverse effect on the human body of the three orthogonal directions when the trucks were used for loading and unloading. The results suggest the CEN test can be applied to the evaluation

The influence of the great Hanshin earthquake on human response to environmental vibration due to the Shinkansen.

PubMed

Sumitomo, S; Tsujimoto, S; Maeda, S; Kitamura, Y

1998-07-01

A severe earthquake of magnitude 7.2 hit the west part of Japan on January 17, 1995. A part of the Shinkansen railway, which is one of the most popular high-speed mass transportation systems in Japan, was seriously damaged by the earthquake. About 80 days later, the Shinkansen service was resumed but complaints about vibration due to the passing Shinkansen increased rapidly among residents near the tracks. This paper reports the results of two investigations that were carried out in both stricken and non-stricken areas to determine the cause of complaint. In the first investigation, the ground vibration propagation induced by passing trains was measured. In the second investigation, questionnaires were distributed to the people living near the Shinkansen tracks. As a result, it was found out that the vibration levels before and after the earthquake were almost the same at most measured points in the stricken area. It was also found that the vibration levels in the stricken area and a non-stricken area were almost the same within 50 m from the Shinkansen tracks. However the results of the questionnaire survey showed that people's nuisance due to the vibration in the stricken area was clearly greater than that in the non-stricken area. This inconsistency was explained using the "category judgment method", which is generally used to determine the relationship between a physical stimulus and psychological reaction. According to the results of this analysis, the vibration level, at which 50% of the inhabitants complained about Shinkansen vibration, was approximately 54 dB in the non-stricken area and 50 dB in the stricken area. This result suggests that the people who experienced the severe earthquake became 4 dB more sensitive to the Shinkansen vibration than the people living in a non-stricken area despite the fact that this investigation was carried out 10 months after the earthquake struck.

Ductile Crack Initiation Criterion with Mismatched Weld Joints Under Dynamic Loading Conditions.

PubMed

An, Gyubaek; Jeong, Se-Min; Park, Jeongung

2018-03-01

Brittle failure of high toughness steel structures tends to occur after ductile crack initiation/propagation. Damages to steel structures were reported in the Hanshin Great Earthquake. Several brittle failures were observed in beam-to-column connection zones with geometrical discontinuity. It is widely known that triaxial stresses accelerate the ductile fracture of steels. The study examined the effects of geometrical heterogeneity and strength mismatches (both of which elevate plastic constraints due to heterogeneous plastic straining) and loading rate on critical conditions initiating ductile fracture. This involved applying the two-parameter criterion (involving equivalent plastic strain and stress triaxiality) to estimate ductile cracking for strength mismatched specimens under static and dynamic tensile loading conditions. Ductile crack initiation testing was conducted under static and dynamic loading conditions using circumferentially notched specimens (Charpy type) with/without strength mismatches. The results indicated that the condition for ductile crack initiation using the two parameter criterion was a transferable criterion to evaluate ductile crack initiation independent of the existence of strength mismatches and loading rates.

Investigation of the line arrangement of 2D resistivity surveys for 3D inversion*

NASA Astrophysics Data System (ADS)

Inoue, Keisuke; Nakazato, Hiroomi; Takeuchi, Mutsuo; Sugimoto, Yoshihiro; Kim, Hee Joon; Yoshisako, Hiroshi; Konno, Michiaki; Shoda, Daisuke

2018-03-01

We have conducted numerical and field experiments to investigate the applicability of electrode configurations and line layouts commonly used for two-dimensional (2D) resistivity surveys to 3D inversion. We examined three kinds of electrode configurations and two types of line arrangements, for 16 resistivity models of a conductive body in a homogeneous half-space. The results of the numerical experiment revealed that the parallel-line arrangement was effective in identifying the approximate location of the conductive body. The orthogonal-line arrangement was optimal for identifying a target body near the line intersection. As a result, we propose that parallel lines are useful to highlight areas of particular interest where further detailed work with an intersecting line could be carried out. In the field experiment, 2D resistivity data were measured on a loam layer with a backfilled pit. The reconstructed resistivity image derived from parallel-line data showed a low-resistivity portion near the backfilled pit. When an orthogonal line was added to the parallel lines, the newly estimated location of the backfilled pit coincided well with the actual location. In a further field application, we collected several 2D resistivity datasets in the Nojima Fault area in Awaji Island. The 3D inversion of these datasets provided a resistivity distribution corresponding to the geological structure. In particular, the Nojima Fault was imaged as the western boundary of a low-resistivity belt, from only two orthogonal lines.

Comparative study of two active faults in different stages of the earthquake cycle in central Japan -The Atera fault (with 1586 Tensho earthquake) and the Nojima fault (with 1995 Kobe earthquake)-

NASA Astrophysics Data System (ADS)

Matsuda, T.; Omura, K.; Ikeda, R.

2003-12-01

National Research Institute for Earth Science and Disaster Prevention (NIED) has been conducting _gFault zone drilling_h. Fault zone drilling is especially important in understanding the structure, composition, and physical properties of an active fault. In the Chubu district of central Japan, large active faults such as the Atotsugawa (with 1858 Hietsu earthquake) and the Atera (with 1586 Tensho earthquake) faults exist. After the occurrence of the 1995 Kobe earthquake, it has been widely recognized that direct measurements in fault zones by drilling. This time, we describe about the Atera fault and the Nojima fault. Because, these two faults are similar in geological situation (mostly composed of granitic rocks), so it is easy to do comparative study of drilling investigation. The features of the Atera fault, which have been dislocated by the 1586 Tensho earthquake, are as follows. Total length is about 70 km. That general trend is NW45 degree with a left-lateral strike slip. Slip rate is estimated as 3-5 m / 1000 years. Seismicity is very low at present and lithologies around the fault are basically granitic rocks and rhyolite. Six boreholes have been drilled from the depth of 400 m to 630 m. Four of these boreholes (Hatajiri, Fukuoka, Ueno and Kawaue) are located on a line crossing in a direction perpendicular to the Atera fault. In the Kawaue well, mostly fractured and alternating granitic rock continued from the surface to the bottom at 630 m. X-ray fluorescence analysis (XRF) is conducted to estimate the amount of major chemical elements using the glass bead method for core samples. The amounts of H20+ are about from 0.5 to 2.5 weight percent. This fractured zone is also characterized by the logging data such as low resistivity, low P-wave velocity, low density and high neutron porosity. The 1995 Kobe (Hyogo-ken Nanbu) earthquake occurred along the NE-SW-trending Rokko-Awaji fault system, and the Nojima fault appeared on the surface on Awaji Island when this

Seismic assessment of a multi-span steel railway bridge in Turkey based on nonlinear time history

NASA Astrophysics Data System (ADS)

Yılmaz, Mehmet F.; Çağlayan, Barlas Ö.

2018-01-01

Many research studies have shown that bridges are vulnerable to earthquakes, graphically confirmed by incidents such as the San Fernando (1971 USA), Northridge (1994 USA), Great Hanshin (1995 Japan), and Chi-Chi (1999 Taiwan) earthquakes, amongst many others. The studies show that fragility curves are useful tools for bridge seismic risk assessments, which can be generated empirically or analytically. Empirical fragility curves can be generated where damage reports from past earthquakes are available, but otherwise, analytical fragility curves can be generated from structural seismic response analysis. Earthquake damage data in Turkey are very limited, hence this study employed an analytical method to generate fragility curves for the Alasehir bridge. The Alasehir bridge is part of the Manisa-Uşak-Dumlupınar-Afyon railway line, which is very important for human and freight transportation, and since most of the country is seismically active, it is essential to assess the bridge's vulnerability. The bridge consists of six 30 m truss spans with a total span 189 m supported by 2 abutments and 5 truss piers, 12.5, 19, 26, 33, and 40 m. Sap2000 software was used to model the Alasehir bridge, which was refined using field measurements, and the effect of 60 selected real earthquake data analyzed using the refined model, considering material and geometry nonlinearity. Thus, the seismic behavior of Alasehir railway bridge was determined and truss pier reaction and displacements were used to determine its seismic performance. Different intensity measures were compared for efficiency, practicality, and sufficiency and their component and system fragility curves derived.

Vacuum delivery at The Maternity Hospital Kuala Lumpur: a comparison of metal and silicone cups.

PubMed

Lee, H Y; Subramaniam, N; Nordin, M M

1996-02-01

To compare the advantages and disadvantages of the New Bird metal cups and silicone cups in terms of maternal and foetal outcome. To study the adverse effects and factors associated with failed vacuum deliveries. A prospective randomised study of all vacuum deliveries from 1 December 1991 to 31 April 1992. The Hanshin electrical vacuum pump was used. A large obstetric unit-The Maternity Hospital Kuala Lumpur (MHKL). Seventy-two consecutive patients where vacuum deliveries were indicated. Forty had metal and 32 had silicone cups. Another 7 vacuum deliveries using the manual vacuum pump were excluded. Success rate of vaginal delivery, birth canal injuries, post-partum haemorrhage, duration of hospital stay, Apgar score, foetal injuries (scalp-ecchymosis, haematomas) neonatal jaundice, the rate of special care nursery (SCN) admission and neonatal mortality rate. Failure to deliver with silicone cups alone was 21.9% compared to 10% for metal cups alone. Material morbidities and serious foetal scalp injuries were almost the same in both cups. However, minor foetal scalp injuries were significantly lower with silicone cups. Maternal height and baby's weight had no independent predictive values for successful vacuum delivery. When the foetal head was palpable per abdomen, the failure rate was 54.5% compared to 8.2% when it was not. Failed vacuum deliveries were associated with increased maternal and foetal morbidities. Silicone cups and metal cups can be equally dangerous to the baby. Although our sample size was small, we recommend that vacuum delivery be avoided if the foetal head is palpable per abdomen.

Case study of medical evacuation before and after the Fukushima Daiichi nuclear power plant accident in the great east Japan earthquake.

PubMed

Okumura, Tetsu; Tokuno, Shinichi

2015-01-01

In Japan, participants in the disaster-specific medical transportation system have received ongoing training since 2002, incorporating lessons learned from the Great Hanshin Earthquake. The Great East Japan Earthquake occurred on March 11, 2011, and the very first disaster-specific medical transport was performed. This article reviews in detail the central government's control and coordination of the disaster medical transportation process following the Great East Japan Earthquake and the Fukushima Daiichi Nuclear Power Plant Accident. In total, 124 patients were air transported under the coordination of the C5 team in the emergency response headquarter of the Japanese Government. C5 includes experts from the Cabinet Office, Cabinet Secretariat, Fire Defense Agency, Ministry of Health, Labour and Welfare, and Ministry of Defense. In the 20-30 km evacuation zone around the Fukushima Daiichi nuclear power plant, 509 bedridden patients were successfully evacuated without any fatalities during transportation. Many lessons have been learned in disaster-specific medical transportation. The national government, local government, police, and fire agencies have made significant progress in their mutual communication and collaboration. Fortunately, hospital evacuation from the 20-30 km area was successfully performed with the aid of local emergency physicians and Disaster Medical Assistance Teams (DMATs) who have vast experience in patient transport in the course of day-to-day activities. The emergency procedures that are required during crises are an extension of basic daily procedures that are performed by emergency medical staff and first responders, such as fire fighters, emergency medical technicians, or police officers. Medical facilities including nursing homes should have a plan for long-distance (over 100 km) evacuation, and the plan should be routinely reevaluated with full-scale exercises. In addition, hospital evacuation in disaster settings should be

Detection of Two Zoonotic Babesia microti Lineages, the Hobetsu and U.S. Lineages, in Two Sympatric Tick Species, Ixodes ovatus and Ixodes persulcatus, Respectively, in Japan

PubMed Central

Tsuji, Masayoshi; Qiang, Wei; Nakao, Minoru; Hirata, Haruyuki; Ishihara, Chiaki

2012-01-01

The species Babesia microti, commonly found in rodents, demonstrates a high degree of genetic diversity. Three lineages, U.S., Kobe, and Hobetsu, are known to have zoonotic potential, but their tick vector(s) in Japan remains to be elucidated. We conducted a field investigation at Nemuro on Hokkaido Island and at Sumoto on Awaji Island, where up to two of the three lineages occur with similar frequencies in reservoirs. By flagging vegetation at these spots and surrounding areas, 4,010 ticks, comprising six species, were collected. A nested PCR that detects the 18S rRNA gene of Babesia species revealed that Ixodes ovatus and I. persulcatus alone were positive. Lineage-specific PCR for rRNA-positive samples demonstrated that I. ovatus and I. persulcatus carried, respectively, the Hobetsu and U.S. parasites. No Kobe-specific DNA was detected. Infected I. ovatus ticks were found at multiple sites, including Nemuro and Sumoto, with minimum infection rates (MIR) of ∼12.3%. However, all I. persulcatus ticks collected within the same regions, a total of 535, were negative for the Hobetsu lineage, indicating that I. ovatus, but not I. persulcatus, was the vector for the lineage. At Nemuro, U.S. lineage was detected in 2 of 139 adult I. persulcatus ticks (MIR, 1.4%), for the first time, while 48 of I. ovatus ticks were negative for that lineage. Laboratory experiments confirmed the transmission of Hobetsu and U.S. parasites to hamsters via I. ovatus and I. persulcatus, respectively. Differences in vector capacity shown by MIRs at Nemuro, where the two species were equally likely to acquire either lineage of parasite, may explain the difference in distribution of Hobetsu throughout Japan and U.S. taxa in Nemuro. These findings are of importance in the assessment of the regional risk for babesiosis in humans. PMID:22389378

Aeromedical Transport Operations Using Helicopters during the 2016 Kumamoto Earthquake in Japan.

PubMed

Motomura, Tomokazu; Hirabayashi, Atsushi; Matsumoto, Hisashi; Yamauchi, Nobutaka; Nakamura, Mitsunobu; Machida, Hiroshi; Fujizuka, Kenji; Otsuka, Naomi; Satoh, Tomoko; Anan, Hideaki; Kondo, Hisayoshi; Koido, Yuichi

2018-01-01

More than 6,000 people died in the Great Hanshin (Kobe) Earthquake in 1995, and it was later reported that there were around 500 preventable trauma deaths. In response, the Japanese government developed the helicopter emergency medical service in 2001, known in Japan as the "Doctor-Heli" (DH), which had 46 DHs and 2 private medical helicopters as of April 2016. DHs transport physicians and nurses to provide pre-hospital medical care at the scene of medical emergencies. Following lessons learned in the Great East Japan Earthquake in 2011, a research group in the Ministry of Health, Labour and Welfare developed a command and control system for the DH fleet as well as the Disaster Relief Aircraft Management System Network (D-NET), which uses a satellite communications network to monitor the location of the fleet and weather in real-time during disasters. During the Kumamoto Earthquake disaster in April 2016, 75 patients were transported by 13 DHs and 1 private medical helicopter in the first 5 days. When medical demand for the DHs exceeded supply, 5 patients, 8 patients, and 1 patient were transported by Self-Defense Force, Fire Department, and Coast Guard helicopters, respectively. Of the 89 patients who were transported, 30 (34%) had trauma, 3 (3%) had pulmonary embolisms caused by sleeping in vehicles, and 17 (19%) were pregnant women or newborns. This was the first time that the command and control system for aeromedical transport and D-NET, established after the Great East Japan Earthquake in 2011, were operated in an actual large-scale disaster. Aeromedical transport by DHs and helicopters belonging to several other organizations was accomplished smoothly because the commanders of the involved organizations could communicate directly with each other in person within the Aviation Coordination Section of the prefectural government office. However, ongoing challenges in the detailed operating methods for aeromedical transport were highlighted and include improving

[Home-oxygen therapy and QOL support for the in the home setting patient].

PubMed

Saito, N

1998-12-01

As a synthetic fiber maker, we Teijin Ltd. used polymer chemistry technology to develop an industrial oxygen-enriching membrane. With this membrane, Teijin had made first domestically manufactured membrane-type oxygen concentrator and entered home oxygen therapy market in 1982, which was three years prior to the start of medical insurance reimbursement for home oxygen therapy. Since then, the company has developed an adsorption-type oxygen concentrator, focused on power and noise reduction, and developed both the "Ultressa," a small, lightweight, portable tank used for outside activities and the "Sanso Saver," an oxygen-conserving device. Teijin also markets the "NIP Nasal", a nasal intemittent positive pressure ventilator. To maintain a development system meeting the needs of health care providers and patients, Teijin operates a direct sales system, currently staffed by specialist representatives in 60 sales offices throughout Japan who provide a rapid response, 24 hours a day, under our motto of "Peace of Mind and Reliability." Teijin not only provides devices; but also sees its function as that of assisting and pursuing QOL for home-based patients through the following services. 1. Teijin has developed TOMS, a monitoring unit connected to an oxygen concentrator in a patient home, which automatically advises a sales office as to the operating condition of the device. TOMS is installed on request, providing peace of mind for those living alone or in isolated locations. 2. When a patient travels, an oxygen concentrator can be installed at any destination in Japan and used free of charge. 3. Teijin supports get-togethers for patients and takes an active part in facilitating bus travel and other recreational activities. 4. To improve ADL and QOL, Teijin has made recent efforts to promote pulmonary rehabilitation, producing videos and booklets available through health care providers. 5. Based on lessons learned from the Great Hanshin Earthquake, the company has

Geometry of the Nojima fault at Nojima-Hirabayashi, Japan - I. A simple damage structure inferred from borehole core permeability

USGS Publications Warehouse

Lockner, David A.; Tanaka, Hidemi; Ito, Hisao; Ikeda, Ryuji; Omura, Kentaro; Naka, Hisanobu

2009-01-01

The 1995 Kobe (Hyogo-ken Nanbu) earthquake, M = 7.2, ruptured the Nojima fault in southwest Japan. We have studied core samples taken from two scientific drillholes that crossed the fault zone SW of the epicentral region on Awaji Island. The shallower hole, drilled by the Geological Survey of Japan (GSJ), was started 75 m to the SE of the surface trace of the Nojima fault and crossed the fault at a depth of 624 m. A deeper hole, drilled by the National Research Institute for Earth Science and Disaster Prevention (NIED) was started 302 m to the SE of the fault and crossed fault strands below a depth of 1140 m. We have measured strength and matrix permeability of core samples taken from these two drillholes. We find a strong correlation between permeability and proximity to the fault zone shear axes. The half-width of the high permeability zone (approximately 15 to 25 m) is in good agreement with the fault zone width inferred from trapped seismic wave analysis and other evidence. The fault zone core or shear axis contains clays with permeabilities of approximately 0.1 to 1 microdarcy at 50 MPa effective confining pressure (10 to 30 microdarcy at in situ pressures). Within a few meters of the fault zone core, the rock is highly fractured but has sustained little net shear. Matrix permeability of this zone is approximately 30 to 60 microdarcy at 50 MPa effective confining pressure (300 to 1000 microdarcy at in situ pressures). Outside this damage zone, matrix permeability drops below 0.01 microdarcy. The clay-rich core material has the lowest strength with a coefficient of friction of approximately 0.55. Shear strength increases with distance from the shear axis. These permeability and strength observations reveal a simple fault zone structure with a relatively weak fine-grained core surrounded by a damage zone of fractured rock. In this case, the damage zone will act as a high-permeability conduit for vertical and horizontal flow in the plane of the

Feasibility of Active Monitoring for Plate Coupling Using ACROSS

NASA Astrophysics Data System (ADS)

Yamaoka, K.; Watanabe, T.; Ikuta, R.

2004-12-01

Detectability of temporal changes in reflected wave from the boundary of subducting plates in Tokai district with active sources are studied. Based on rock experiments the change in the intensity of reflection wave can be caused by change in coupling between subducting and overriding plates. ACROSS (Accurately-Controlled Rountine-Operated Signal System) consists of sinusoidal vibration sources and receivers is proved to provide a data of excellent signal resolution. The following technical issues should be overcome to monitor the returned signal from boundaries of subducting plates. (1) Long term operation of the source. (2) Detection of temporal change. (3) Accurate estimation of source functions and their temporal change. First two issues have already overcome. We have already succeeded a long-term operation experiment with the ACROSS system in Awaji, Japan. The operation was carried out for 15 months with only minor troubles. Continuous signal during the experiment are successfully obtained. In the experiment we developed a technique to monitor the temporal change of travel time with a resolution of several tens of microseconds. The third issue is one of the most difficult problem for practical monitoring using artificial sources. In the 15-month experiment we correct the source function using the record of seismometers that were deployed around the source We also estimate the efficiency of the reflected wave detection using ACROSS system. We use a data of seismic exploration experiment by blasts that carried out above subducting plate in Tokai district. Clear reflection from the surface of the Philippine Sea plate is observed in the waveform. Assuming that the ACROSS source is installed at the same place of the blast source, the detectability of temporal variation of reflection wave can be estimated. As we have measured the variation of signal amplitude that depends on the distance from an ACROSS source, ground noise at seismic stations (receivers) provide us

In-situ stress measurements using core-based methods in the vicinity of Nojima fault.

NASA Astrophysics Data System (ADS)

Yano, S.; Sugimoto, T.; Lin, W.; Lin, A.

2017-12-01

In the cycle of repeatable occurrence of earthquakes, stress accumulates at the source fault and its surroundings in an interseismic period until the next earthquake, and releases abruptly when the earthquake occurs. However, it is almost unknown that the quantitative relationship between stress change and earthquake occurrence. Hence, in order to improve our understanding on the mechanisms of the outbreak of earthquakes, it is important to grasp the stress states in the vicinity of the source fault and to evaluate its change over time. In this study, we carried out in-situ stress measurements by using core samples obtained from a scientific drilling penetrated through the Nojima fault which ruptured and caused the Hyogo-ken Nanbu earthquake, Japan in 1995. Our stress measurements were conducted from 2016 to 2017 when is 22 years after the earthquake. For this purpose, we applied the Anelastic Strain Recovery (ASR) method and Diametrical Core Deformation Analysis (DCDA). First, we measure the ASR change with time of the cores from stress releasing soon and calculate three-dimensional principal in-situ stress orientations and magnitudes from the ASR data. In this study, to ensure the enough amount of ASR, we conducted the measurements using the cores collected within a short time (e.g. 2.5 - 3.5 hours) after stress releasing by drilling at an on-site laboratory in the drilling site in Awaji island, Japan. The site locates at the south-west part of the Nojima fault. In DCDA, we measure the core diameters in all (360°) azimuths, and determine difference of the two horizontal principal stresses and their orientation by using the other cores as those used for ASR. DCDA experiments were conducted indoor and after a long time passed from core collecting. Lithology of all the core samples we used for ASR and DCDA are granite, and 19 and 7 cores were used for ASR and DCDA, respectively. As a result, it was found that the stress state in the depth range of 500 - 560 m and

PREFACE: 6th Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS11)

NASA Astrophysics Data System (ADS)

Lupi, Stefano; Perucchi, Andrea

2012-05-01

This volume of Journal of Physics: Conference Series is dedicated to a subset of papers related to the work presented at the 6th edition of the international Workshop on Infrared Spectroscopy and Microscopy with Accelerator-Based Sources (WIRMS), held in Trieste, Italy, September 4-8 2011. Previous editions of the conference were held in Porquerolles (France), Lake Tahoe (USA), Rathen (Germany), Awaji (Japan), and Banff (Canada). This edition was organized and chaired by Stefano Lupi (Roma La Sapienza) and co-chaired by Andrea Perucchi (Elettra), with the support of the Italian Synchrotron Light Laboratory ELETTRA, which was honored to host the WIRMS workshop in its tenth anniversary. The 6th WIRMS edition addressed several different topics, ranging from biochemistry to strongly correlated materials, from geology to conservation science, and from forensics to the study of cometary dusts. Representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities. This edition was attended by 88 participants, including representatives from the infrared scientific programs at synchrotron light sources and free-electron-laser facilities, who enjoyed the stimulating scientific presentations, several detailed discussions, and the beautiful weather and scenery of the Trieste gulf. Participants came from 16 different nations and four continents, including many young scientists, six of which were supported by the organizers. There were 45 scientific talks divided in 11 sessions: Facilities, Microspectroscopy (I, II, III), Time-Resolved Spectroscopies, Extreme Conditions, Condensed Matter, Near-Field, Imaging, THz Techniques and High-Resolution Spectroscopy. 37 posters were also presented at two very lively evening poster sessions. We would like to use the opportunity of writing this preface to thank all the participants of the workshop for the very high level of their scientific contribution and for the very friendly atmosphere

EDITORIAL: Announcing the 2010 Measurement Science and Technology Outstanding Paper Awards Announcing the 2010 Measurement Science and Technology Outstanding Paper Awards

NASA Astrophysics Data System (ADS)

Foss, John; Dewhurst, Richard; Fujii, Kenichi; Regtien, Paul

2011-06-01

dc magnetic field for stable and supercooled liquid silicon Hidekazu Kobatake, Hiroyuki Fukuyama, Takao Tsukada and Satoshi Awaji Institute of Multidisciplinary Research for Advanced Materials (IMRAM), Tohoku University, 2-1-1 Katahira, Aoba, Sendai, 980-8577, Japan Department of Chemical Engineering, Tohoku University, Aramaki Aoba, Aoba-ku, Sendai, 980-8577, Japan Institute for Materials Research (IMR), Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577, Japan An accurate value of the thermal conductivity of supercooled liquid silicon proves very helpful to better numerical heat flow models used for the production of high-quality silicon crystals. Measuring this important parameter is a challenge since the accuracy is frustrated by convections and imprecise non-contact temperature measurements, resulting in a wide variation of values reported in the literature so far. By improving the non-contact temperature measurement on a magnetically levitated drop of silicon the authors succeeded in a substantial reduction of the uncertainty in the measured values of the heat capacity and the thermal conductivity including their temperature dependence. Modulation of the heat power and an accurate measurement of the amplitude and phase of the resulting temperature variation constitute the major contribution to a higher accuracy. In their winning paper [4] the authors present a clear overview of their measurement setup and the experimental procedure and conditions, and give an extensive analysis of the parameters that play a part in the overall uncertainty. Measured values are compared with those obtained by other methods and reported in relevant literature. Moreover, the improvements of the instrumentation implemented by the authors contribute to a better understanding of the heat transport processes in liquid silicon. The four chairmen would like to thank the authors for choosing to publish their work in Measurement Science and Technology, and hope that other

PREFACE: Exploring surfaces and buried interfaces of functional materials by advanced x-ray and neutron techniques Exploring surfaces and buried interfaces of functional materials by advanced x-ray and neutron techniques

NASA Astrophysics Data System (ADS)

Sakurai, Kenji

2010-12-01

Awaji, Toyoo Miyajima, Shuuichi Doi and Kenji Nomura

Particle processing technology

NASA Astrophysics Data System (ADS)

Sakka, Yoshio

2014-02-01

achievements that are not covered in this special issue. (1) The evolution of hydrogen by the reaction of fine metal particles such as Al [14] and Mg [15] with water; the specific surface area and surface modification are important factors.(2) The realization of new carbon related materials with 1D and 2D structures consisting of fullerenes prepared by liquid-liquid interface precipitation: alkaline-doped superconductive nanotubes consisting of fullerenes [16], application to solar cells of fullerene/cobalt porphyrin hybrid nanosheets [17], etc.(3) The fabrication of textured films and bulk materials with excellent functional properties by colloidal processing methods such as slip casting [5], gel casting [18] and electrophoretic deposition [3, 19], in a high magnetic field, and with subsequent heating; examples of such materials include dye-sensitized TiO2 solar cells, thermoelectric materials and cathode materials for solid state Li-ion batteries and dielectric ceramics.(4) The fabrication of high-strength and high-toughness MAX phase ceramics [20, 21] inspired by the nacreous structure [22].(5) The modeling and development of the ECAS process [6]. This involves two-step pressure application [23] and high-pressure application above 400 MPa to fabricate transparent oxides [24-26], and rapid heating to obtain dense nanocomposites of ceramic-CNT [27] and diamonds [28].(6) The contraction of ternary phase diagrams for oxide ion conductor systems such as zirconia [29] and apatite systems [30], leading to an increased understanding of the stability of such systems and assisting the search for high oxygen ion conductors. Acknowledgments I am grateful to the authors who have contributed to this special issue, and sincerely hope that the readers will expand their knowledge of particle processing technology. References [1] Sakka Y 2006 J. Ceram. Soc. Japan 114 371 [2] Badica P, Crisan A, Aldica G, Endo K, Borodianska H, Togano K, Awaji S, Vasylkiv O and Sakka Y 2011 Sci. Technol. Adv