Modeling the Technological Process for Harvesting of Agricultural Produce

NASA Astrophysics Data System (ADS)

Shepelev, S. D.; Shepelev, V. D.; Almetova, Z. V.; Shepeleva, N. P.; Cheskidov, M. V.

2018-01-01

The efficiency and the parameters of harvesting as a technological process being substantiated make it possible to reduce the cost of production and increase the profit of enterprises. To increase the efficiency of combine harvesters when the level of technical equipment declines is possible due to their efficient operating modes within daily and every season. Therefore, the correlation between the operational daily time and the seasonal load of combine harvesters is found, with the increase in the seasonal load causing the prolonged duration of operational daily time for harvesters being determined. To increase the efficient time of the seasonal load is possible due to a reasonable ratio of crop varieties according to their ripening periods, the necessary quantity of machines thereby to be reduced up to 40%. By timing and field testing the operational factor of the useful shift time of combine harvesters and the efficient modes of operating machines are defined, with the alternatives for improving the technical readiness of combine harvesters being identified.

Influence of Weather on the Predicted Moisture Content of Field Chopped EnergySorghum and Switchgrass

DOE PAGES

Popp, Michael P.; Searcy, Stephen S.; Sokhansanj, Shahab; ...

2015-03-25

To determine the effects of weather on harvested moisture content (MC) of switchgrass (Panicum virgatum) and energy sorghum (Sorghum bicolor), tracking of harvest progress on individual fields in the Integrated Biomass Supply and Logistics (IBSAL) model was modified to allow: i) rewetting of swathed material in the drying formulae; and ii) field queuing rules based on equipment availability and weather. Estimated crop yield and initial MC by harvest date, as observed in field trials, along with the modeling of different delays between mowing and harvest allowed estimation of harvested MC, annual tonnage processed and associated processing cost differences by cropmore » and location over 10 years. Extending the hours of annual equipment use had minor implications on cost of production. Energy sorghum proved difficult to dry in the field. Its higher yield, leading to shorter supply distance to the plant, may justify harvesting of energy sorghum early in the season with drier weather. Lastly, later harvest for lower-yielding switchgrass offers MC advantages.« less

Influence of Weather on the Predicted Moisture Content of Field Chopped EnergySorghum and Switchgrass

DOE Office of Scientific and Technical Information (OSTI.GOV)

Popp, Michael P.; Searcy, Stephen S.; Sokhansanj, Shahab

To determine the effects of weather on harvested moisture content (MC) of switchgrass (Panicum virgatum) and energy sorghum (Sorghum bicolor), tracking of harvest progress on individual fields in the Integrated Biomass Supply and Logistics (IBSAL) model was modified to allow: i) rewetting of swathed material in the drying formulae; and ii) field queuing rules based on equipment availability and weather. Estimated crop yield and initial MC by harvest date, as observed in field trials, along with the modeling of different delays between mowing and harvest allowed estimation of harvested MC, annual tonnage processed and associated processing cost differences by cropmore » and location over 10 years. Extending the hours of annual equipment use had minor implications on cost of production. Energy sorghum proved difficult to dry in the field. Its higher yield, leading to shorter supply distance to the plant, may justify harvesting of energy sorghum early in the season with drier weather. Lastly, later harvest for lower-yielding switchgrass offers MC advantages.« less

Method and apparatus for selectively harvesting multiple components of a plant material

DOEpatents

Hoskinson, Reed L.; Hess, Richard J.; Kenney, Kevin L.; Svoboda, John M.; Foust, Thomas D.

2004-05-04

A method and apparatus for selectively harvesting multiple components of a plant material. A grain component is separated from the plant material such as by processing the plant material through a primary threshing and separating mechanism. At least one additional component of the plant material is selectively harvested such as by subjecting the plant material to a secondary threshing and separating mechanism. For example, the stems of a plant material may be broken at a location adjacent one or more nodes thereof with the nodes and the internodal stem portions being subsequently separated for harvesting. The at least one additional component (e.g., the internodal stems) may then be consolidated and packaged for subsequent use or processing. The harvesting of the grain and of the at least one additional component may occur within a single harvesting machine, for example, during a single pass over a crop field.

The effect of seed cotton moisture during harvesting on - part 2- yarn and fabric quality

USDA-ARS?s Scientific Manuscript database

Part 1 of this study found that there were significant differences in terms of fiber quality and processing performance of seed cotton harvested from one field using a John Deere 7760 spindle harvester at two moisture levels, <12% and >12%, and storing the harvested modules for 12 weeks prior to gin...

Roll splitting as an alternative intermediate process for wood fuel

Treesearch

Paul E. Barnett; Donald L. Sirois

1985-01-01

In an effort to develop mobile equipment for harvesting and processing woody biomass from power line rights-of-way and precommerial thinnings, numerous alternative concepts were evaluated by Tennessee Valley Authority's Timber Harvesting Project.

[Effects of post-harvest processing and extraction methods on polysaccharides content of Dendrobium officinale].

PubMed

Li, Cong; Ning, Li-Dan; Si, Jin-Ping; Wu, Ling-Shang; Liu, Jing-Jing; Song, Xian-Shui; Yu, Qiao-Xian

2013-02-01

To reveal the quality variation of polysaccharide in Dendrobium officinale by post-harvest processing and extraction methods, and provide a basis for post-harvest processing and clinical and hygienical applications of Tiepifengdou (Dendrobii Officinalis Caulis). The content of polysaccharides were studied by 4 post-harvest processing methods, i. e. drying by drying closet, drying after scalding by boiling water, drying while twisting, and drying while twisting after scalding by boiling water. And a series of temperatures were set in each processing procedure. An orthogonal test L9 (3(4)) with crushed degrees, solid-liquid ratio, extraction time and extraction times as factors were designed to analyze the dissolution rate of polysaccharides in Tiepifengdou processed by drying while twisting at 80 degrees C. The content of polysaccharides was ranged from 26.59% to 32.70% in different samples processed by different processing methods, among which drying while twisting at 80 degrees C and 100 degrees C respectively were the best. Crushed degree was the most important influence on the dissolution rate of polysaccharides. The dissolution rate of polysaccharides was extremely low when the sample was boiled directly without crushing and sieving. Drying while twisting at 80 degrees C was the best post-harvest processing method, which can help to dry the fresh herbs and improve the accumulation of polysaccharides. Boiling the uncrushed Tiepifengdou for a long time as traditional method could not fully extract polysaccharides, while boiling the crushed Tiepifengdou can efficiently extract polysaccharides.

Water Harvesting II: Working toward Being Green

ERIC Educational Resources Information Center

Farenga, Stephen J.; Ness, Daniel; Craven, John A.

2008-01-01

As you have read in the previous "After the Bell" column, water harvesting is a process of diverting and collecting rainwater. One of the main reasons to harvest rainwater is to reduce the demand on local sources of water. The objective of the harvesting procedure is to gather water from a weather event that is usually lost as runoff and either…

Rubber finger stripper harvester for green chile

USDA-ARS?s Scientific Manuscript database

Harvest mechanization as a system requires modifying or creating new components including cultivars, production practices, and harvest, transportation and processing plant machinery. New Mexican chile is one of the last segments of the pepper industry to still rely on hand labor. This paper reports ...

Influence of forest and rangeland management on anadromous fish habitat in Western North America: timber harvest.

Treesearch

T.W. Chamberlin

1982-01-01

The water and land-system processes through which timber harvesting affects anadromous fish habitat in western North America are discussed. The effects of timber harvesting on the water balance that regulates streamflow are evaluated, as are direct influences of harvesting on slope stability, erosion, and the introduction of debris in to stream channels. The effects of...

Factors influencing kenaf harvesting and processing in the United States

USDA-ARS?s Scientific Manuscript database

The selection of the appropriate kenaf (Hibiscus cannabinus L., Malvaceae) production and harvest system is dependent on many factors, including location, equipment availability, storage options, processing plants, plant utilization, and economics. Since its first domestication, kenaf has consisten...

Tracking cotton fiber quality throughout a stipper harvester: Part II

USDA-ARS?s Scientific Manuscript database

Cotton fiber quality begins to degrade naturally with the opening of the boll and mechanical harvesting processes are perceived to exacerbate fiber degradation. Previous research indicates that stripper harvested cotton generally has lower fiber quality and higher foreign matter content than picker ...

Stump Harvesting

Treesearch

Dana Mitchell

2009-01-01

Increased use of forest fuel requires larger and larger procurement areas. Inclusion of stump material within the shorter distances could make this unusual source of biomass more economical to harvest. Land clearing activities are also helping to raise interest in stump harvesting. Processing stump material for biomass is an alternative...

Magnetophoretic harvesting of oleaginous Chlorella sp. by using biocompatible chitosan/magnetic nanoparticle composites.

PubMed

Lee, Kyubock; Lee, So Yeun; Na, Jeong-Geol; Jeon, Sang Goo; Praveenkumar, Ramasamy; Kim, Dong-Myung; Chang, Won-Seok; Oh, You-Kwan

2013-12-01

The consumption of energy and resources such as water in the cultivation and harvesting steps should be minimized to reduce the overall cost of biodiesel production from microalgae. Here we present a biocompatible and rapid magnetophoretic harvesting process of oleaginous microalgae by using chitosan-Fe3O4 nanoparticle composites. Over 99% of microalgae was harvested by using the composites and the external magnetic field without changing the pH of culture medium so that it may be reused for microalgal culture without adverse effect on the cell growth. Depending on the working volume (20-500 mL) and the strength of surface magnetic-field (3400-9200 G), the process of harvesting microalgae took only 2-5 min. The method presented here not only utilizes permanent magnets without additional energy for fast harvesting but also recycles the medium effectively for further cultivation of microalgae, looking ahead to a large scale economic microalgae-based biorefinement. Copyright © 2013 Elsevier Ltd. All rights reserved.

Image Harvest: an open-source platform for high-throughput plant image processing and analysis

PubMed Central

Knecht, Avi C.; Campbell, Malachy T.; Caprez, Adam; Swanson, David R.; Walia, Harkamal

2016-01-01

High-throughput plant phenotyping is an effective approach to bridge the genotype-to-phenotype gap in crops. Phenomics experiments typically result in large-scale image datasets, which are not amenable for processing on desktop computers, thus creating a bottleneck in the image-analysis pipeline. Here, we present an open-source, flexible image-analysis framework, called Image Harvest (IH), for processing images originating from high-throughput plant phenotyping platforms. Image Harvest is developed to perform parallel processing on computing grids and provides an integrated feature for metadata extraction from large-scale file organization. Moreover, the integration of IH with the Open Science Grid provides academic researchers with the computational resources required for processing large image datasets at no cost. Image Harvest also offers functionalities to extract digital traits from images to interpret plant architecture-related characteristics. To demonstrate the applications of these digital traits, a rice (Oryza sativa) diversity panel was phenotyped and genome-wide association mapping was performed using digital traits that are used to describe different plant ideotypes. Three major quantitative trait loci were identified on rice chromosomes 4 and 6, which co-localize with quantitative trait loci known to regulate agronomically important traits in rice. Image Harvest is an open-source software for high-throughput image processing that requires a minimal learning curve for plant biologists to analyzephenomics datasets. PMID:27141917

Learning and adaptation in the management of waterfowl harvests

USGS Publications Warehouse

Johnson, Fred A.

2011-01-01

A formal framework for the adaptive management of waterfowl harvests was adopted by the U.S. Fish and Wildlife Service in 1995. The process admits competing models of waterfowl population dynamics and harvest impacts, and relies on model averaging to compute optimal strategies for regulating harvest. Model weights, reflecting the relative ability of the alternative models to predict changes in population size, are used in the model averaging and are updated each year based on a comparison of model predictions and observations of population size. Since its inception the adaptive harvest program has focused principally on mallards (Anas platyrhynchos), which constitute a large portion of the U.S. waterfowl harvest. Four competing models, derived from a combination of two survival and two reproductive hypotheses, were originally assigned equal weights. In the last year of available information (2007), model weights favored the weakly density-dependent reproductive hypothesis over the strongly density-dependent one, and the additive mortality hypothesis over the compensatory one. The change in model weights led to a more conservative harvesting policy than what was in effect in the early years of the program. Adaptive harvest management has been successful in many ways, but nonetheless has exposed the difficulties in defining management objectives, in predicting and regulating harvests, and in coping with the tradeoffs inherent in managing multiple waterfowl stocks exposed to a common harvest. The key challenge now facing managers is whether adaptive harvest management as an institution can be sufficiently adaptive, and whether the knowledge and experience gained from the process can be reflected in higher-level policy decisions.

Carbon metabolism of peach fruit after harvest: changes in enzymes involved in organic acid and sugar level modifications.

PubMed

Borsani, Julia; Budde, Claudio O; Porrini, Lucía; Lauxmann, Martin A; Lombardo, Verónica A; Murray, Ricardo; Andreo, Carlos S; Drincovich, María F; Lara, María V

2009-01-01

Peach (Prunus persica L. Batsch) is a climacteric fruit that ripens after harvest, prior to human consumption. Organic acids and soluble sugars contribute to the overall organoleptic quality of fresh peach; thus, the integrated study of the metabolic pathways controlling the levels of these compounds is of great relevance. Therefore, in this work, several metabolites and enzymes involved in carbon metabolism were analysed during the post-harvest ripening of peach fruit cv 'Dixiland'. Depending on the enzyme studied, activity, protein level by western blot, or transcript level by quantitative real time-PCR were analysed. Even though sorbitol did not accumulate at a high level in relation to sucrose at harvest, it was rapidly consumed once the fruit was separated from the tree. During the ripening process, sucrose degradation was accompanied by an increase of glucose and fructose. Specific transcripts encoding neutral invertases (NIs) were up-regulated or down-regulated, indicating differential functions for each putative NI isoform. Phosphoenolpyruvate carboxylase was markedly induced, and may participate as a glycolytic shunt, since the malate level did not increase during post-harvest ripening. The fermentative pathway was highly induced, with increases in both the acetaldehyde level and the enzymes involved in this process. In addition, proteins differentially expressed during the post-harvest ripening process were also analysed. Overall, the present study identified enzymes and pathways operating during the post-harvest ripening of peach fruit, which may contribute to further identification of varieties with altered levels of enzymes/metabolites or in the evaluation of post-harvest treatments to produce fruit of better organoleptic attributes.

Harvesting

Treesearch

John R. Jones; Wayne D. Shepperd

1985-01-01

Harvesting is the removal of produce from the forest for utilization. It includes cutting, any further initial processing, such as topping and trimming, and extraction (Ford-Robertson 1971). Commercial intermediate cutting, such as commercial thinning, as well as regeneration cutting are included. Harvesting and the income that it produces sometimes is regarded as an...

Bioaugmentation for Groundwater Remediation

DTIC Science & Technology

2010-02-01

continually grown and harvested , in fed batch mode where a culture is grown in a vessel and harvested and then another culture begun, or in a hybrid of...the two whereby the culture is maintained in a fermentor until a volume of culture is harvested and then replaced with fresh medium. The primary...producing cultures for bioaugmentation is a semi- continuous process whereby the culture is maintained in the fermentor until needed and then harvested

High-efficiency integrated piezoelectric energy harvesting systems

NASA Astrophysics Data System (ADS)

Hande, Abhiman; Shah, Pradeep

2010-04-01

This paper describes hierarchically architectured development of an energy harvesting (EH) system that consists of micro and/or macro-scale harvesters matched to multiple components of remote wireless sensor and communication nodes. The micro-scale harvesters consist of thin-film MEMS piezoelectric cantilever arrays and power generation modules in IC-like form to allow efficient EH from vibrations. The design uses new high conversion efficiency thin-film processes combined with novel cantilever structures tuned to multiple resonant frequencies as broadband arrays. The macro-scale harvesters are used to power the collector nodes that have higher power specifications. These bulk harvesters can be integrated with efficient adaptive power management circuits that match transducer impedance and maximize power harvested from multiple scavenging sources with very low intrinsic power consumption. Texas MicroPower, Inc. is developing process based on a composition that has the highest reported energy density as compared to other commercially available bulk PZT-based sensor/actuator ceramic materials and extending it to thin-film materials and miniature conversion transducer structures. The multiform factor harvesters can be deployed for several military and commercial applications such as underground unattended sensors, sensors in oil rigs, structural health monitoring, supply chain management, and battlefield applications such as sensors on soldier apparel, equipment, and wearable electronics.

Development of economic and environmental metrics for forest-based biomass harvesting

NASA Astrophysics Data System (ADS)

Zhang, F. L.; Wang, J. J.; Liu, S. H.; Zhang, S. M.

2016-08-01

An assessment of the economic, energy consumption, and greenhouse gas (GHG) emission dimensions of forest-based biomass harvest stage in the state of Michigan, U.S. through gathering data from literature, database, and other relevant sources, was performed. The assessment differentiates harvesting systems (cut-to-length harvesting, whole tree harvesting, and motor-manual harvesting), harvest types (30%, 70%, and 100% cut) and forest types (hardwoods, softwoods, mixed hardwood/softwood, and softwood plantations) that characterize Michigan's logging industry. Machine rate methods were employed to determine unit harvesting cost. A life cycle inventory was applied to calculating energy demand and GHG emissions of different harvesting scenarios, considering energy and material inputs (diesel, machinery, etc.) and outputs (emissions) for each process (cutting, forwarding/skidding, etc.). A sensitivity analysis was performed for selected input variables for the harvesting operation in order to explore their relative importance. The results indicated that productivity had the largest impact on harvesting cost followed by machinery purchase price, yearly scheduled hours, and expected utilization. Productivity and fuel use, as well as fuel factors, are the most influential environmental impacts of harvesting operations.

Natural fiber production, harvesting, and preliminary processing: options and opportunities

USDA-ARS?s Scientific Manuscript database

The utilization of natural fibers and plant oils in bio-products introduces numerous logistical challenges not typically encountered with non-agricultural resources. Once it has been determined that a plant material is suitable for commercial development, the production, harvesting, and processing s...

Sub-lethal behavioral and physiological effects of the biomedical bleeding process on the American horseshoe crab, Limulus polyphemus

PubMed Central

Anderson, Rebecca L.; Watson, Winsor H.; Chabot, Christopher C.

2014-01-01

The hemolymph of the American horseshoe crab, Limulus polyphemus, is harvested from over 500,000 animals annually to produce Limulus Amebocyte Lysate, a medically important product used to detect pathogenic bacteria. Declining abundance of spawning Limulus females in heavily harvested regions suggests deleterious effects of this activity and, while mortality rates of the harvest process are known to be 10–30%, sub-lethal behavioral and physiological effects are not known. In this study, we determined the impact of the harvest process on locomotion and hemocyanin levels of 28 female horseshoe crabs. While mortality rates after bleeding (18%) were similar to previous studies, we found significant decreases in the linear and angular velocity of freely moving animals, as well as changes in their activity levels and expression of circatidal behavioral rhythms. Further, we found reductions in hemocyanin levels, which may alter immune function and cuticle integrity. These previously unrecognized behavioral and physiological deficits suggest that the harvest of Limulus Amebocyte Lysate may decrease female fitness, and thus may contribute to the current population decline. PMID:24445440

Potential Ambient Energy-Harvesting Sources and Techniques

ERIC Educational Resources Information Center

Yildiz, Faruk

2009-01-01

Ambient energy harvesting is also known as energy scavenging or power harvesting, and it is the process where energy is obtained from the environment. A variety of techniques are available for energy scavenging, including solar and wind powers, ocean waves, piezoelectricity, thermoelectricity, and physical motions. For example, some systems…

Comparison of a wire belt conveyor and cross auger conveyor for conveying burr cotton on a stripper harvester

USDA-ARS?s Scientific Manuscript database

Cotton fiber quality begins to degrade naturally with the opening of the boll, and mechanical harvesting processes are perceived to exacerbate fiber degradation. Previous research indicates that stripper-harvested cotton generally has lower fiber quality including on average lower micronaire, length...

A novel method to harvest Chlorella sp. by co-flocculation/air flotation.

PubMed

Zhang, Haiyang; Lin, Zhe; Tan, Daoyong; Liu, Chunhua; Kuang, Yali; Li, Zhu

2017-01-01

To develop a more effective dissolved air flotation process for harvesting microalgae biomass, a co-flocculation/air flotation (CAF) system was developed that uses an ejector followed by a helix tube flocculation reactor (HTFR) as a co-flocculation device to harvest Chlorella sp. 64.01. The optimal size distribution of micro-bubbles and an air release efficiency of 96 % were obtained when the flow ratio of inlet fluid (raw water) to motive fluid (saturated water) of the ejector was 0.14. With a reaction time of 24 s in the HTFR, microalgae cells and micro-bubbles were well flocculated, and these aerated flocs caused a fast rising velocity (96 m/h) and high harvesting efficiency (94 %). In a CAF process, micro-bubbles can be encapsulated into microalgae flocs, which makes aerated flocs more stable. CAF is an effective approach to harvesting microalgae.

Toward energy harvesting using active materials and conversion improvement by nonlinear processing.

PubMed

Guyomar, Daniel; Badel, Adrien; Lefeuvre, Elie; Richard, Claude

2005-04-01

This paper presents a new technique of electrical energy generation using mechanically excited piezoelectric materials and a nonlinear process. This technique, called synchronized switch harvesting (SSH), is derived from the synchronized switch damping (SSD), which is a nonlinear technique previously developed to address the problem of vibration damping on mechanical structures. This technique results in a significant increase of the electromechanical conversion capability of piezoelectric materials. Comparatively with standard technique, the electrical harvested power may be increased above 900%. The performance of the nonlinear processing is demonstrated on structures excited at their resonance frequency as well as out of resonance.

Agricultural management affects evolutionary processes in a migratory songbird

USGS Publications Warehouse

Perlut, N.G.; Freeman-Gallant, C. R.; Strong, A.M.; Donovan, T.M.; Kilpatrick, C.W.; Zalik, N.J.

2008-01-01

Hay harvests have detrimental ecological effects on breeding songbirds, as harvesting results in nest failure. Importantly, whether harvesting also affects evolutionary processes is not known. We explored how hay harvest affected social and genetic mating patterns, and thus, the overall opportunity for sexual selection and evolutionary processes for a ground-nesting songbird, the Savannah sparrow (Passerculus sandwichensis). On an unharvested field, 55% of females were in polygynous associations, and social polygyny was associated with greater rates of extra-pair paternity (EPP). In this treatment, synchrony explained variation in EPP rates, as broods by more synchronous females had more EPP than broods by asynchronous females. In contrast, on a harvested field, simultaneous nest failure caused by haying dramatically decreased the overall incidence of EPP by increasing the occurrence of social monogamy and, apparently, the ability of polygynous males to maintain paternity in their own nests. Despite increased social and genetic monogamy, these haying-mediated changes in mating systems resulted in greater than twofold increase in the opportunity for sexual selection. This effect arose, in part, from a 30% increase in the variance associated with within-pair fertilization success, relative to the unharvested field. This effect was caused by a notable increase (+110%) in variance associated with the quality of social mates following simultaneous nest failure. Because up to 40% of regional habitat is harvested by early June, these data may demonstrate a strong population-level effect on mating systems, sexual selection, and consequently, evolutionary processes. ?? 2008 The Authors.

Factors affecting unintentional harvesting selectivity in a monomorphic species.

PubMed

Bunnefeld, Nils; Baines, David; Newborn, David; Milner-Gulland, E J

2009-03-01

1. Changes in the abundance of populations have always perplexed ecologists but long-term studies are revealing new insights into population dynamic processes. Long-term data are often derived from harvest records although many wild populations face high harvesting pressures leading to overharvesting and extinction. Additionally, harvest records used to describe population processes such as fluctuations in abundance and reproductive success often assume a random off-take. 2. Selective harvesting based on phenotypic characteristics occurs in many species (e.g. trophy hunting, fisheries) and has important implications for population dynamics, conservation and management. 3. In species with no marked morphological differences between the age and sex classes, such as the red grouse Lagopus lagopus scoticus during the shooting season, hunters cannot consciously select for a specific sex or age class during the shooting process but harvest records could still give a biased reflection of the population structure because of differences in behaviour between age and sex classes. 4. This study compared age and sex ratios in the bag with those in the population before shooting for red grouse at different points in the shooting season and different densities, which has rarely been tested before. 5. More young than old grouse were shot at large bag sizes and vice versa for small bag sizes than would be expected from the population composition before shooting. The susceptibility of old males to shooting compared to females increased with bag size and was high at the first time the area was shot but decreased with the number of times an area was harvested. 6. These findings stress that the assumption made in many studies that harvest records reflect the age and sex ratio of the population and therefore reflect productivity can be misleading. 7. In this paper, as in the literature, it is also shown that number of grouse shot reflects grouse density and therefore that hunting selectivity might influence population dynamics in a cyclic species. 8. The study is not only relevant for red grouse but applies to systems showing interactions between selective harvesting and wider ecological processes, such as age- and sex-related parasitism and territoriality, which may drive population fluctuations.

Image Harvest: an open-source platform for high-throughput plant image processing and analysis.

PubMed

Knecht, Avi C; Campbell, Malachy T; Caprez, Adam; Swanson, David R; Walia, Harkamal

2016-05-01

High-throughput plant phenotyping is an effective approach to bridge the genotype-to-phenotype gap in crops. Phenomics experiments typically result in large-scale image datasets, which are not amenable for processing on desktop computers, thus creating a bottleneck in the image-analysis pipeline. Here, we present an open-source, flexible image-analysis framework, called Image Harvest (IH), for processing images originating from high-throughput plant phenotyping platforms. Image Harvest is developed to perform parallel processing on computing grids and provides an integrated feature for metadata extraction from large-scale file organization. Moreover, the integration of IH with the Open Science Grid provides academic researchers with the computational resources required for processing large image datasets at no cost. Image Harvest also offers functionalities to extract digital traits from images to interpret plant architecture-related characteristics. To demonstrate the applications of these digital traits, a rice (Oryza sativa) diversity panel was phenotyped and genome-wide association mapping was performed using digital traits that are used to describe different plant ideotypes. Three major quantitative trait loci were identified on rice chromosomes 4 and 6, which co-localize with quantitative trait loci known to regulate agronomically important traits in rice. Image Harvest is an open-source software for high-throughput image processing that requires a minimal learning curve for plant biologists to analyzephenomics datasets. © The Author 2016. Published by Oxford University Press on behalf of the Society for Experimental Biology.

INFINITY harvest

NASA Image and Video Library

2012-05-07

Lauren Lombard from Benjamin E. Mays Preparatory School in New Orleans enjoys lettuce she helped to harvest at the INFINITY at NASA Stennis Space Center facility May 7, 2012. The Louisiana students assisted in the first harvest of lettuce from the Controlled Environment Agriculture unit, which uses an aeroponic process that involves no soil and advance LED lighting techniques

INFINITY harvest

NASA Image and Video Library

2012-05-07

Shania Etheridge from Benjamin E. Mays Preparatory School in New Orleans shows off the head of lettuce she harvested at the INFINITY at NASA Stennis Space Center facility May 7, 2012. The Louisiana students assisted in the first harvest of lettuce from the Controlled Environment Agriculture unit, which uses an aeroponic process that involves no soil and advance LED lighting techniques.

Effects of forest harvest on biogeochemical processes in the Caspar Creek watershed

Treesearch

Randy A. Dahlgren

1998-01-01

Water quality and long-term sustainability are major components addressed within the ecosystem approach to forest management. Forest harvest practices are often implicated as having adverse impacts on sensitive aquatic communities and on the long-term sustainability of forest ecosystems. While careless harvest practices can certainly cause adverse impacts, proper...

Timber Harvesting Effects After 16 Years in a Tupelo-Cypress Swamp

Treesearch

Paul A. Gellerstedt; W. Michael Aust

2004-01-01

A variety of concerns have been expressed regarding harvesting in forested wetlands. These concerns usually revolve around such issues as potential losses in site productivity, altered wetland functional processes, and development of appropriate best management practices. In 1985 a long-term study was established to evaluate harvest disturbance effects on water quality...

High School Harvest: Combining Food Service Training and Institutional Procurement

ERIC Educational Resources Information Center

Conner, David; Estrin, Hans; Becot, Florence

2014-01-01

This article discusses High School Harvest (HSH), an Extension educator-led project in five Vermont schools to provide students with job training and food system education and to provide lightly processed produce to school lunch programs. One hundred and twenty-one students participated, logging 8,752 hours growing, harvesting, and processing…

A Skin-attachable Flexible Piezoelectric Pulse Wave Energy Harvester

NASA Astrophysics Data System (ADS)

Yoon, Sunghyun; Cho, Young-Ho

2014-11-01

We present a flexible piezoelectric generator, capable to harvest energy from human arterial pulse wave on the human wrist. Special features and advantages of the flexible piezoelectric generator include the multi-layer device design with contact windows and the simple fabrication process for the higher flexibility with the better energy harvesting efficiency. We have demonstrated the design effectiveness and the process simplicity of our skin- attachable flexible piezoelectric pulse wave energy harvester, composed of the sensitive P(VDF-TrFE) piezoelectric layer on the flexible polyimide support layer with windows. We experimentally characterize and demonstrate the energy harvesting capability of 0.2~1.0μW in the Human heart rate range on the skin contact area of 3.71cm2. Additional physiological and/or vital signal monitoring devices can be fabricated and integrated on the skin attachable flexible generator, covered by an insulation layer; thus demonstrating the potentials and advantages of the present device for such applications to the flexible multi-functional selfpowered artificial skins, capable to detect physiological and/or vital signals on Human skin using the energy harvested from arterial pulse waves.

46 CFR 356.55 - Review of compliance with harvesting and processing quotas.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 8 2010-10-01 2010-10-01 false Review of compliance with harvesting and processing quotas. 356.55 Section 356.55 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MISCELLANEOUS REQUIREMENTS FOR VESSELS OF 100 FEET OR GREATER IN REGISTERED LENGTH TO OBTAIN A FISHERY...

46 CFR 356.55 - Review of compliance with harvesting and processing quotas.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 8 2011-10-01 2011-10-01 false Review of compliance with harvesting and processing quotas. 356.55 Section 356.55 Shipping MARITIME ADMINISTRATION, DEPARTMENT OF TRANSPORTATION MISCELLANEOUS REQUIREMENTS FOR VESSELS OF 100 FEET OR GREATER IN REGISTERED LENGTH TO OBTAIN A FISHERY...

Timber harvest calculations on a National Forest: A case study

NASA Astrophysics Data System (ADS)

Carey, Henry H.

1983-03-01

Harvest calculations determine sawtimber flows from public lands and are closely scruntinized by a wide spectrum of forest users. This study examines the reliability of harvest calculations on a single national forest in New Mexico Forest Service determinations of an array of variables were reviewed and evaluated. The study revealed a lack of precision in Forest Service adherence to self-imposed procedural standards governing the calculation process. Timber sales have taken place on lands where such standards prohibit harvesting and these lands have been included in annual harvest calculations. Assumptions required by a mathematical model used by the Forest Service in calculating the harvest were not followed in the subsequent implementation of the harvest level. These factors suggest that the Forest Service could have significantly over-stated annual harvest rate for the first decade. Opportunities exist to improve the calculation, and benefits realized may greatly exceed additional costs of implementation

Physical and sensory quality of Java Arabica green coffee beans

NASA Astrophysics Data System (ADS)

Sunarharum, W. B.; Yuwono, S. S.; Pangestu, N. B. S. W.; Nadhiroh, H.

2018-03-01

Demand on high quality coffee for consumption is continually increasing not only in the consuming countries (importers) but also in the producing countries (exporters). Coffee quality could be affected by several factors from farm to cup including the post-harvest processing methods. This research aimed to investigate the influence of different post-harvest processing methods on physical and sensory quality of Java Arabica green coffee beans. The two factors being evaluated were three different post-harvest processing methods to produce green coffee beans (natural/dry, semi-washed and fully-washed processing) under sun drying. Physical quality evaluation was based on The Indonesian National Standard (SNI 01-2907-2008) while sensory quality was evaluated by five expert judges. The result shows that less defects observed in wet processed coffee as compared to the dry processing. The mechanical drying was also proven to yield a higher quality green coffee beans and minimise losses.

An efficient start-up circuitry for de-energized ultra-low power energy harvesting systems

NASA Astrophysics Data System (ADS)

Hörmann, Leander B.; Berger, Achim; Salzburger, Lukas; Priller, Peter; Springer, Andreas

2015-05-01

Cyber-physical systems often include small wireless devices to measure physical quantities or control a technical process. These devices need a self-sufficient power supply because no wired infrastructure is available. Their operational time can be enhanced by energy harvesting systems. However, the convertible power is often limited and discontinuous which requires the need of an energy storage unit. If this unit (and thus the whole system) is de-energized, the start-up process may take a significant amount of time because of an inefficient energy harvesting process. Therefore, this paper presents a system which enables a safe and fast start-up from the de-energized state.

K-wire assisted split-thickness skin graft harvesting from the anterior trunk.

PubMed

Yontar, Yalcin; Coruh, Atilla; Severcan, Mehmet

2016-02-01

Split thickness skin graft (STSG) harvesting from the anterior chest and abdominal wall skin is quite a difficult process. The main reason for the difficulty to perform this process is the unsuitable anatomic characteristics of the anterior trunk, such as irregular wavy-like surface over the ribs and lax abdominal wall skin resulting in collapse due to lack of adequate underneath supporting structures when a downward force is applied by the skin graft dermatome. Lower extremity and especially the thigh are generally chosen as the donor site where the STSGs are easily harvested from. However, extensive lower extremity burns, with or without other region burns, preclude harvesting auto STSGs from this invaluable anatomic site. We harvested K-wire assisted STSGs from the anterior chest and abdominal wall skin of 7 patients with lower extremity burns and also a patient that sustained motor vehicle collision. We encountered no problems in any of our patients both intra and postoperatively by using K-wire assisted STSG harvesting. All of the STSGs donor sites healed uneventfully without complications. In our opinion, K-wire assisted STSG harvesting must always be in the tool-box of any surgeon who deals with extensive burns with or without lower extremity burns and extensive traumas of lower extremities. Copyright © 2015 Elsevier Ltd and ISBI. All rights reserved.

Review of the harvesting and extraction program within the National Alliance for Advanced Biofuels and Bioproducts

DOE PAGES

Marrone, Babetta L.; Lacey, Ronald E.; Anderson, Daniel B.; ...

2017-08-07

Energy-efficient and scalable harvesting and lipid extraction processes must be developed in order for the algal biofuels and bioproducts industry to thrive. The major challenge for harvesting is the handling of large volumes of cultivation water to concentrate low amounts of biomass. For lipid extraction, the major energy and cost drivers are associated with disrupting the algae cell wall and drying the biomass before solvent extraction of the lipids. Here we review the research and development conducted by the Harvesting and Extraction Team during the 3-year National Alliance for Advanced Biofuels and Bioproducts (NAABB) algal consortium project. The harvesting andmore » extraction team investigated five harvesting and three wet extraction technologies at lab bench scale for effectiveness, and conducted a techoeconomic study to evaluate their costs and energy efficiency compared to available baseline technologies. Based on this study, three harvesting technologies were selected for further study at larger scale. We evaluated the selected harvesting technologies: electrocoagulation, membrane filtration, and ultrasonic harvesting, in a field study at minimum scale of 100 L/h. None of the extraction technologies were determined to be ready for scale-up; therefore, an emerging extraction technology (wet solvent extraction) was selected from industry to provide scale-up data and capabilities to produce lipid and lipid-extracted materials for the NAABB program. One specialized extraction/adsorption technology was developed that showed promise for recovering high value co-products from lipid extracts. Overall, the NAABB Harvesting and Extraction Team improved the readiness level of several innovative, energy efficient technologies to integrate with algae production processes and captured valuable lessons learned about scale-up challenges.« less

Review of the harvesting and extraction program within the National Alliance for Advanced Biofuels and Bioproducts

DOE Office of Scientific and Technical Information (OSTI.GOV)

Marrone, Babetta L.; Lacey, Ronald E.; Anderson, Daniel B.

Energy-efficient and scalable harvesting and lipid extraction processes must be developed in order for the algal biofuels and bioproducts industry to thrive. The major challenge for harvesting is the handling of large volumes of cultivation water to concentrate low amounts of biomass. For lipid extraction, the major energy and cost drivers are associated with disrupting the algae cell wall and drying the biomass before solvent extraction of the lipids. Here we review the research and development conducted by the Harvesting and Extraction Team during the 3-year National Alliance for Advanced Biofuels and Bioproducts (NAABB) algal consortium project. The harvesting andmore » extraction team investigated five harvesting and three wet extraction technologies at lab bench scale for effectiveness, and conducted a techoeconomic study to evaluate their costs and energy efficiency compared to available baseline technologies. Based on this study, three harvesting technologies were selected for further study at larger scale. We evaluated the selected harvesting technologies: electrocoagulation, membrane filtration, and ultrasonic harvesting, in a field study at minimum scale of 100 L/h. None of the extraction technologies were determined to be ready for scale-up; therefore, an emerging extraction technology (wet solvent extraction) was selected from industry to provide scale-up data and capabilities to produce lipid and lipid-extracted materials for the NAABB program. One specialized extraction/adsorption technology was developed that showed promise for recovering high value co-products from lipid extracts. Overall, the NAABB Harvesting and Extraction Team improved the readiness level of several innovative, energy efficient technologies to integrate with algae production processes and captured valuable lessons learned about scale-up challenges.« less

Response of sugar beet recombinant inbred lines to post-harvest rot fungi

USDA-ARS?s Scientific Manuscript database

Sugar beet is commonly stored in outdoor piles prior to processing. During this storage period the crop is subject to multiple post-harvest rots. Resistance to three post harvest rots was identified in two sugar beet germplasm in the 1970s, but there has been little work done on host resistance to p...

Response of sugar beet (Beta vulgaris) recombinant inbred lines to post-harvest rot fungi

USDA-ARS?s Scientific Manuscript database

Sugar beet (Beta vulgaris) is commonly stored in outdoor piles prior to processing for food and animal feed. During this storage period the crop is subject to multiple post-harvest rots. Resistance to three post harvest rots was identified in two sugar beet germplasm in the 1970s, but there has been...

Microwave moisture sensing of seedcotton: Part 1: Seedcotton microwave material properties

USDA-ARS?s Scientific Manuscript database

Moisture content at harvest is a key parameter that impacts quality and how well the cotton crop can be stored without degrading before processing. It is also a key parameter of interest for harvest time field trials as it can directly influence the quality of the harvested crop as well as alter the...

Microwave moisture sensing of seedcotton: Part 1: Seedcotton microwave material properties

USDA-ARS?s Scientific Manuscript database

Moisture content at harvest is a key parameter that impacts quality and how well the cotton crop can be stored without degrading before processing. It is also a key parameter of interest for harvest time field trials as it can directly influence the quality of the harvested crop as well as skew the...

Review of the harvesting and extraction of advanced biofuels and bioproducts

Treesearch

Babette L. Marrone;  Ronald E.  Lacey;  Daniel B. Anderson;  James Bonner;  Jim Coons;  Taraka Dale;  Cara Meghan Downes;  Sandun Fernando;  Christopher  Fuller;  Brian Goodall;  Johnathan E. Holladay;  Kiran Kadam;  Daniel  Kalb;  Wei  Liu;  John B. Mott;  Zivko Nikolov;  Kimberly L. Ogden;  Richard T. Sayre;  Brian G. Trewyn;  José A. Olivares

2017-01-01

Energy-efficient and scalable harvesting and lipid extraction processes must be developed in order for the algal biofuels and bioproducts industry to thrive. The major challenge for harvesting is the handling of large volumes of cultivation water to concentrate low amounts of biomass. For lipid extraction, the major energy and cost drivers are associated with...

Development and Testing of an Ultra Low Power System-On-Chip (SOC) Platform for Marine Mammal Tags and Passive Acoustic Signal Processing

DTIC Science & Technology

2014-09-30

current (3-5mA). The system can harvest 16 power from a DC input source like a thermoelectric generator (TEG) or photovoltaic cell (PV). The boost...results from components to report. Designed for thermoelectric energy harvesting in 130nm CMOS, the boost converter reduces the achievable input...harvesting. The boost converter further incorporates maximum power point tracking for harvesting from both thermoelectric generators (TEGs) and solar

Imports and exports of roundwood in the upper Midwestern United States. Chapter 2.

Treesearch

Charles H. Perry; Mark D. Nelson; Ronald J. Piva

2010-01-01

Industrial roundwood is the raw material produced from harvested trees that is used to manufacture a wide range of wood products. Roundwood is harvested from the forest and is transported to primary manufacturing facilities to be processed into primary and secondary wood products. Roundwood includes sawlogs that are processed into...

Catchment hydrological responses to forest harvest amount and spatial pattern

Treesearch

Alex Abdelnour; Marc Stieglitz; Feifei Pan; Robert McKane

2011-01-01

Forest harvest effects on streamflow generation have been well described experimentally, but a clear understanding of process-level hydrological controls can be difficult to ascertain from data alone. We apply a new model, Visualizing Ecosystems for Land Management Assessments (VELMA), to elucidate how hillslope and catchment-scale processes control stream discharge in...

Bare Iron Oxide Nanoparticles for Magnetic Harvesting of Microalgae: From Interaction Behavior to Process Realization.

PubMed

Fraga-García, Paula; Kubbutat, Peter; Brammen, Markus; Schwaminger, Sebastian; Berensmeier, Sonja

2018-05-01

Microalgae continue to gain in importance as a bioresource, while their harvesting remains a major challenge at the moment. This study presents findings on microalgae separation using low-cost, easy-to-process bare iron oxide nanoparticles with the additional contribution of the upscaling demonstration of this simple, adhesion-based process. The high affinity of the cell wall for the inorganic surface enables harvesting efficiencies greater than 95% for Scenedesmus ovalternus and Chlorella vulgaris . Successful separation is possible in a broad range of environmental conditions and primarily depends on the nanoparticle-to-microalgae mass ratio, whereas the effect of pH and ionic strength are less significant when the mass ratio is chosen properly. The weakening of ionic concentration profiles at the interphase due to the successive addition of deionized water leads the microalgae to detach from the nanoparticles. The process works efficiently at the liter scale, enabling complete separation of the microalgae from their medium and the separate recovery of all materials (algae, salts, and nanoparticles). The current lack of profitable harvesting processes for microalgae demands innovative approaches to encourage further development. This application of magnetic nanoparticles is an example of the prospects that nanobiotechnology offers for biomass exploitation.

B-HIT - A Tool for Harvesting and Indexing Biodiversity Data

PubMed Central

Barker, Katharine; Braak, Kyle; Cawsey, E. Margaret; Coddington, Jonathan; Robertson, Tim; Whitacre, Jamie

2015-01-01

With the rapidly growing number of data publishers, the process of harvesting and indexing information to offer advanced search and discovery becomes a critical bottleneck in globally distributed primary biodiversity data infrastructures. The Global Biodiversity Information Facility (GBIF) implemented a Harvesting and Indexing Toolkit (HIT), which largely automates data harvesting activities for hundreds of collection and observational data providers. The team of the Botanic Garden and Botanical Museum Berlin-Dahlem has extended this well-established system with a range of additional functions, including improved processing of multiple taxon identifications, the ability to represent associations between specimen and observation units, new data quality control and new reporting capabilities. The open source software B-HIT can be freely installed and used for setting up thematic networks serving the demands of particular user groups. PMID:26544980

B-HIT - A Tool for Harvesting and Indexing Biodiversity Data.

PubMed

Kelbert, Patricia; Droege, Gabriele; Barker, Katharine; Braak, Kyle; Cawsey, E Margaret; Coddington, Jonathan; Robertson, Tim; Whitacre, Jamie; Güntsch, Anton

2015-01-01

With the rapidly growing number of data publishers, the process of harvesting and indexing information to offer advanced search and discovery becomes a critical bottleneck in globally distributed primary biodiversity data infrastructures. The Global Biodiversity Information Facility (GBIF) implemented a Harvesting and Indexing Toolkit (HIT), which largely automates data harvesting activities for hundreds of collection and observational data providers. The team of the Botanic Garden and Botanical Museum Berlin-Dahlem has extended this well-established system with a range of additional functions, including improved processing of multiple taxon identifications, the ability to represent associations between specimen and observation units, new data quality control and new reporting capabilities. The open source software B-HIT can be freely installed and used for setting up thematic networks serving the demands of particular user groups.

PDADMAC flocculation of Chinese hamster ovary cells: enabling a centrifuge-less harvest process for monoclonal antibodies.

PubMed

McNerney, Thomas; Thomas, Anne; Senczuk, Anna; Petty, Krista; Zhao, Xiaoyang; Piper, Rob; Carvalho, Juliane; Hammond, Matthew; Sawant, Satin; Bussiere, Jeanine

2015-01-01

High titer (>10 g/L) monoclonal antibody (mAb) cell culture processes are typically achieved by maintaining high viable cell densities over longer culture durations. A corresponding increase in the solids and sub-micron cellular debris particle levels are also observed. This higher burden of solids (≥15%) and sub-micron particles typically exceeds the capabilities of a continuous centrifuge to effectively remove the solids without a substantial loss of product and/or the capacity of the harvest filtration train (depth filter followed by membrane filter) used to clarify the centrate. We discuss here the use of a novel and simple two-polymer flocculation method used to harvest mAb from high cell mass cell culture processes. The addition of the polycationic polymer, poly diallyldimethylammonium chloride (PDADMAC) to the cell culture broth flocculates negatively-charged cells and cellular debris via an ionic interaction mechanism. Incorporation of a non-ionic polymer such as polyethylene glycol (PEG) into the PDADMAC flocculation results in larger flocculated particles with faster settling rate compared to PDADMAC-only flocculation. PDADMAC also flocculates the negatively-charged sub-micron particles to produce a feed stream with a significantly higher harvest filter train throughput compared to a typical centrifuged harvest feed stream. Cell culture process variability such as lactate production, cellular debris and cellular densities were investigated to determine the effect on flocculation. Since PDADMAC is cytotoxic, purification process clearance and toxicity assessment were performed.

PDADMAC flocculation of Chinese hamster ovary cells: Enabling a centrifuge-less harvest process for monoclonal antibodies

PubMed Central

McNerney, Thomas; Thomas, Anne; Senczuk, Anna; Petty, Krista; Zhao, Xiaoyang; Piper, Rob; Carvalho, Juliane; Hammond, Matthew; Sawant, Satin; Bussiere, Jeanine

2015-01-01

High titer (>10 g/L) monoclonal antibody (mAb) cell culture processes are typically achieved by maintaining high viable cell densities over longer culture durations. A corresponding increase in the solids and sub-micron cellular debris particle levels are also observed. This higher burden of solids (≥15%) and sub-micron particles typically exceeds the capabilities of a continuous centrifuge to effectively remove the solids without a substantial loss of product and/or the capacity of the harvest filtration train (depth filter followed by membrane filter) used to clarify the centrate. We discuss here the use of a novel and simple two-polymer flocculation method used to harvest mAb from high cell mass cell culture processes. The addition of the polycationic polymer, poly diallyldimethylammonium chloride (PDADMAC) to the cell culture broth flocculates negatively-charged cells and cellular debris via an ionic interaction mechanism. Incorporation of a non-ionic polymer such as polyethylene glycol (PEG) into the PDADMAC flocculation results in larger flocculated particles with faster settling rate compared to PDADMAC-only flocculation. PDADMAC also flocculates the negatively-charged sub-micron particles to produce a feed stream with a significantly higher harvest filter train throughput compared to a typical centrifuged harvest feed stream. Cell culture process variability such as lactate production, cellular debris and cellular densities were investigated to determine the effect on flocculation. Since PDADMAC is cytotoxic, purification process clearance and toxicity assessment were performed. PMID:25706650

West Virginia timber industry: an assessment of timber product output and use, 2007

Treesearch

Ronald J. Piva; Gregory W. Cook

2011-01-01

In 2007, there were 116 primary wood-processing mills in West Virginia, 60 fewer mills than in 2000. These mills processed 172.9 million cubic feet of industrial roundwood, of which 138.8 million cubic feet was harvested from the State. Another 50.5 million cubic feet of the industrial roundwood harvested in West Virginia was sent to primary wood-processing mills in...

Nutritive value of corn silage as affected by maturity and mechanical processing: a contemporary review.

PubMed

Johnson, L; Harrison, J H; Hunt, C; Shinners, K; Doggett, C G; Sapienza, D

1999-12-01

Stage of maturity at harvest and mechanical processing affect the nutritive value of corn silage. The change in nutritive value of corn silage as maturity advances can be measured by animal digestion and macro in situ degradation studies among other methods. Predictive equations using climatic data, vitreousness of corn grain in corn silage, starch reactivity, gelatinization enthalpy, dry matter (DM) of corn grain in corn silage, and DM of corn silage can be used to estimate starch digestibility of corn silage. Whole plant corn silage can be mechanically processed either pre- or postensiling with a kernel processor mounted on a forage harvester, a recutter screen on a forage harvester, or a stationary roller mill. Mechanical processing of corn silage can improve ensiling characteristics, reduce DM losses during ensiling, and improve starch and fiber digestion as a result of fracturing the corn kernels and crushing and shearing the stover and cobs. Improvements in milk production have ranged from 0.2 to 2.0 kg/d when cows were fed mechanically processed corn silage. A consistent improvement in milk protein yield has also been observed when mechanically processed corn silage has been fed. With the advent of mechanical processors, alternative strategies are evident for corn silage management, such as a longer harvest window.

Berry ripening, pre-processing and thermal treatments affect the phenolic composition and antioxidant capacity of grape (Vitis vinifera L.) juice.

PubMed

Genova, Giuseppe; Tosetti, Roberta; Tonutti, Pietro

2016-01-30

Grape juice is an important dietary source of health-promoting antioxidant molecules. Different factors may affect juice composition and nutraceutical properties. The effects of some of these factors (harvest time, pre-processing ethylene treatment of grapes and juice thermal pasteurization) were here evaluated, considering in particular the phenolic composition and antioxidant capacity. Grapes (Vitis vinifera L., red-skinned variety Sangiovese) were collected twice in relation to the technological harvest (TH) and 12 days before TH (early harvest, EH) and treated with gaseous ethylene (1000 ppm) or air for 48 h. Fresh and pasteurized (78 °C for 30 min) juices were produced using a water bath. Three-way analysis of variance showed that the harvest date had the strongest impact on total polyphenols, hydroxycinnamates, flavonols, and especially on total flavonoids. Pre-processing ethylene treatment significantly increased the proanthocyanidin, anthocyanin and flavan-3-ol content in the juices. Pasteurization induced a significant increase in anthocyanin concentration. Antioxidant capacity was enhanced by ethylene treatment and pasteurization in juices from both TH and EH grapes. These results suggest that an appropriate management of grape harvesting date, postharvest and processing may lead to an improvement in nutraceutical quality of juices. Further research is needed to study the effect of the investigated factors on juice organoleptic properties. © 2015 Society of Chemical Industry.

Energy-producing electro-flocculation for harvest of Dunaliella salina.

PubMed

Liu, Qing; Zhang, Meng; Lv, Tao; Chen, Hongjun; Chika, Anthony Okonkwo; Xiang, Changli; Guo, Minxue; Wu, Minghui; Li, Jianjun; Jia, Lishan

2017-10-01

In this study, an efficient electro-flocculation process for Dunaliella salina with energy production by aluminum-air battery has been successfully applied. The formed aluminum hydroxide hydrates during discharging of battery were positively charged, which have a great potential for microalgae flocculation. The precipitation of aluminum hydroxide hydrates by algae also could improve the performance of aluminum-air battery. The harvesting efficiency could reach 97% in 20mins with energy production of 0.11kWh/kg. This discharging electro-flocculation (DEF) technology provides a new energy producing process to effectively harvest microalgae. Copyright © 2017 Elsevier Ltd. All rights reserved.

iTRAQ-based analysis of changes in the cassava root proteome reveals pathways associated with post-harvest physiological deterioration.

PubMed

Owiti, Judith; Grossmann, Jonas; Gehrig, Peter; Dessimoz, Christophe; Laloi, Christophe; Hansen, Maria Benn; Gruissem, Wilhelm; Vanderschuren, Hervé

2011-07-01

The short storage life of harvested cassava roots is an important constraint that limits the full potential of cassava as a commercial food crop in developing countries. We investigated the molecular changes during physiological deterioration of cassava root after harvesting using isobaric tags for relative and absolute quantification (iTRAQ) of proteins in soluble and non-soluble fractions prepared during a 96 h post-harvest time course. Combining bioinformatic approaches to reduce information redundancy for unsequenced or partially sequenced plant species, we established a comprehensive proteome map of the cassava root and identified quantitatively regulated proteins. Up-regulation of several key proteins confirmed that physiological deterioration of cassava root after harvesting is an active process, with 67 and 170 proteins, respectively, being up-regulated early and later after harvesting. This included regulated proteins that had not previously been associated with physiological deterioration after harvesting, such as linamarase, glutamic acid-rich protein, hydroxycinnamoyl transferase, glycine-rich RNA binding protein, β-1,3-glucanase, pectin methylesterase, maturase K, dehydroascorbate reductase, allene oxide cyclase, and proteins involved in signal pathways. To confirm the regulation of these proteins, activity assays were performed for selected enzymes. Together, our results show that physiological deterioration after harvesting is a highly regulated complex process involving proteins that are potential candidates for biotechnology approaches to reduce such deterioration. © 2011 The Authors. The Plant Journal © 2011 Blackwell Publishing Ltd.

INFINITY harvest

NASA Image and Video Library

2012-05-07

Janice Hueschen of Innovative Imaging & Research Corp. at Stennis Space Center helps students from Benjamin E. Mays Preparatory School in New Orleans harvest lettuce at the INFINITY at NASA Stennis Space Center facility May 7, 2012. The Louisiana students assisted in the first harvest of lettuce from the Controlled Environment Agriculture unit, which uses an aeroponic process that involves no soil and advance LED lighting techniques.

Destalking the Wily Tomato: A Case Study in Social Consequences in California Agricultural Research. Research Monograph No. 15.

ERIC Educational Resources Information Center

Friedland, William H.; Barton, Amy

The end of the bracero program after 1965 brought about a major change in the growing, harvesting, and processing of California tomatoes which dramatically influenced the structure of the harvesting labor force. In order to determine the social consequences of the transition from man to mechanized harvesting procedures, the following areas of…

Mechanized or hand operations: which is less expensive for small timber?

Treesearch

Robert Rummber; John Klepac

2002-01-01

Two harvesting systems, one manual post-and-rail and one small-scale cut-to-length harvester, were compared in a lodgepole pine thinning. Elemental time study data were collected, along with estimates of residual stand damage. The harvester was about as productive as a manual crew of five. For material 5" and larger, the cost for felling, processing and piling...

A three-stage heuristic for harvest scheduling with access road network development

Treesearch

Mark M. Clark; Russell D. Meller; Timothy P. McDonald

2000-01-01

In this article we present a new model for the scheduling of forest harvesting with spatial and temporal constraints. Our approach is unique in that we incorporate access road network development into the harvest scheduling selection process. Due to the difficulty of solving the problem optimally, we develop a heuristic that consists of a solution construction stage...

Minnesota timber industry: an assessment of timber product output and use, 2010

Treesearch

Brian F. Walters; Steve Vongroven; Ronald J. Piva

2016-01-01

In 2010, there were 417 active primary wood-using mills in Minnesota. These mills processed 238.8 million cubic feet of industrial roundwood. There was 226.1 million cubic feet of industrial roundwood harvested from Minnesota forests. The majority of roundwood harvested was pulpwood, accounting for 61 percent of the total. The harvesting of industrial roundwood...

78 FR 11988 - Migratory Bird Subsistence Harvest in Alaska; Harvest Regulations for Migratory Birds in Alaska...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-02-21

...-management process involving the Service, the Alaska Department of Fish and Game, and Alaska Native... developed under a co-management process involving the Service, the Alaska Department of Fish and Game, and... Fish and Game's request to expand the Fairbanks North Star Borough excluded area to include the Central...

Current progress and future prospect of microalgal biomass harvest using various flocculation technologies.

PubMed

Wan, Chun; Alam, Md Asraful; Zhao, Xin-Qing; Zhang, Xiao-Yue; Guo, Suo-Lian; Ho, Shih-Hsin; Chang, Jo-Shu; Bai, Feng-Wu

2015-05-01

Microalgae have been extensively studied for the production of various valuable products. Application of microalgae for the production of renewable energy has also received increasing attention in recent years. However, high cost of microalgal biomass harvesting is one of the bottlenecks for commercialization of microalgae-based industrial processes. Considering harvesting efficiency, operation economics and technological feasibility, flocculation is a superior method to harvest microalgae from mass culture. In this article, the latest progress of various microalgal cell harvesting methods via flocculation is reviewed with the emphasis on the current progress and prospect in environmentally friendly bio-based flocculation. Harvesting microalgae through bio-based flocculation is a promising component of the low-cost microalgal biomass production technology. Copyright © 2014 Elsevier Ltd. All rights reserved.

50 CFR 600.330 - National Standard 5-Efficiency.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Efficiency. In theory, an efficient fishery would harvest the OY with the minimum use of economic inputs such... techniques of harvesting, processing, or marketing, and should avoid creating strong incentives for excessive...

Oregon's forest products industry and timber harvest, 2003.

Treesearch

Jason P. Brandt; Todd A. Morgan; Thale Dillon; Gary J. Lettman; Charles E. Keegan; David L. Azuma

2006-01-01

This Report traces the flow of Oregon’s 2003 timber harvest through the primary timber-processing industry and describes its structure, operations and condition. Pulp and board, lumber, and plywood and veer sectors accounted for 96 percent of total industry sales of $6.7 billion. Oregon’s 2003 timber harvest of just over 4 billion board feet was 95 percent softwood...

78 FR 62331 - Fisheries of the Northeastern United States; Atlantic Herring Fishery; Sub-Annual Catch Limit...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-10-17

...-Annual Catch Limit (ACL) Harvested for Management Area 1A AGENCY: National Marine Fisheries Service (NMFS..., acceptable biological catch, annual catch limit (ACL), optimum yield, domestic harvest and processing, U.S... Harvest is 107,800 metric tons (mt); the 2013 sub-ACL allocated to Area 1A is 29,775 mt, and 0 mt of the...

Analysis of straw row in the image to control the trajectory of the agricultural combine harvester

NASA Astrophysics Data System (ADS)

Shkanaev, Aleksandr Yurievich; Polevoy, Dmitry Valerevich; Panchenko, Aleksei Vladimirovich; Krokhina, Darya Alekseevna; Nailevish, Sadekov Rinat

2018-04-01

The paper proposes a solution to the automatic operation of the combine harvester along the straw rows by means of the images from the camera, installed in the cab of the harvester. The U-Net is used to recognize straw rows in the image. The edges of the row are approximated in the segmented image by the curved lines and further converted into the harvester coordinate system for the automatic operating system. The "new" network architecture and approaches to the row approximation has improved the quality of the recognition task and the processing speed of the frames up to 96% and 7.5 fps, respectively. Keywords: Grain harvester,

Molecular analysis of post-harvest withering in grape by AFLP transcriptional profiling

PubMed Central

Zamboni, Anita; Minoia, Leone; Ferrarini, Alberto; Tornielli, Giovanni Battista; Zago, Elisa; Delledonne, Massimo; Pezzotti, Mario

2008-01-01

Post-harvest withering of grape berries is used in the production of dessert and fortified wines to alter must quality characteristics and increase the concentration of simple sugars. The molecular processes that occur during withering are poorly understood, so a detailed transcriptomic analysis of post-harvest grape berries was carried out by AFLP-transcriptional profiling analysis. This will help to elucidate the molecular mechanisms of berry withering and will provide an opportunity to select markers that can be used to follow the drying process and evaluate different drying techniques. AFLP-TP identified 699 withering-specific genes, 167 and 86 of which were unique to off-plant and on-plant withering, respectively. Although similar molecular events were revealed in both withering processes, it was apparent that off-plant withering induced a stronger dehydration stress response resulting in the high level expression of genes involved in stress protection mechanisms, such as dehydrin and osmolite accumulation. Genes involved in hexose metabolism and transport, cell wall composition, and secondary metabolism (particularly the phenolic and terpene compound pathways) were similarly regulated in both processes. This work provides the first comprehensive analysis of the molecular events underpinning post-harvest withering and could help to define markers for different withering processes. PMID:19010774

Molecular analysis of post-harvest withering in grape by AFLP transcriptional profiling.

PubMed

Zamboni, Anita; Minoia, Leone; Ferrarini, Alberto; Tornielli, Giovanni Battista; Zago, Elisa; Delledonne, Massimo; Pezzotti, Mario

2008-01-01

Post-harvest withering of grape berries is used in the production of dessert and fortified wines to alter must quality characteristics and increase the concentration of simple sugars. The molecular processes that occur during withering are poorly understood, so a detailed transcriptomic analysis of post-harvest grape berries was carried out by AFLP-transcriptional profiling analysis. This will help to elucidate the molecular mechanisms of berry withering and will provide an opportunity to select markers that can be used to follow the drying process and evaluate different drying techniques. AFLP-TP identified 699 withering-specific genes, 167 and 86 of which were unique to off-plant and on-plant withering, respectively. Although similar molecular events were revealed in both withering processes, it was apparent that off-plant withering induced a stronger dehydration stress response resulting in the high level expression of genes involved in stress protection mechanisms, such as dehydrin and osmolite accumulation. Genes involved in hexose metabolism and transport, cell wall composition, and secondary metabolism (particularly the phenolic and terpene compound pathways) were similarly regulated in both processes. This work provides the first comprehensive analysis of the molecular events underpinning post-harvest withering and could help to define markers for different withering processes.

Bare Iron Oxide Nanoparticles for Magnetic Harvesting of Microalgae: From Interaction Behavior to Process Realization

PubMed Central

Brammen, Markus; Berensmeier, Sonja

2018-01-01

Microalgae continue to gain in importance as a bioresource, while their harvesting remains a major challenge at the moment. This study presents findings on microalgae separation using low-cost, easy-to-process bare iron oxide nanoparticles with the additional contribution of the upscaling demonstration of this simple, adhesion-based process. The high affinity of the cell wall for the inorganic surface enables harvesting efficiencies greater than 95% for Scenedesmus ovalternus and Chlorella vulgaris. Successful separation is possible in a broad range of environmental conditions and primarily depends on the nanoparticle-to-microalgae mass ratio, whereas the effect of pH and ionic strength are less significant when the mass ratio is chosen properly. The weakening of ionic concentration profiles at the interphase due to the successive addition of deionized water leads the microalgae to detach from the nanoparticles. The process works efficiently at the liter scale, enabling complete separation of the microalgae from their medium and the separate recovery of all materials (algae, salts, and nanoparticles). The current lack of profitable harvesting processes for microalgae demands innovative approaches to encourage further development. This application of magnetic nanoparticles is an example of the prospects that nanobiotechnology offers for biomass exploitation. PMID:29723963

Clarification of vaccines: An overview of filter based technology trends and best practices.

PubMed

Besnard, Lise; Fabre, Virginie; Fettig, Michael; Gousseinov, Elina; Kawakami, Yasuhiro; Laroudie, Nicolas; Scanlan, Claire; Pattnaik, Priyabrata

2016-01-01

Vaccines are derived from a variety of sources including tissue extracts, bacterial cells, virus particles, recombinant mammalian, yeast and insect cell produced proteins and nucleic acids. The most common method of vaccine production is based on an initial fermentation process followed by purification. Production of vaccines is a complex process involving many different steps and processes. Selection of the appropriate purification method is critical to achieving desired purity of the final product. Clarification of vaccines is a critical step that strongly impacts product recovery and subsequent downstream purification. There are several technologies that can be applied for vaccine clarification. Selection of a harvesting method and equipment depends on the type of cells, product being harvested, and properties of the process fluids. These techniques include membrane filtration (microfiltration, tangential-flow filtration), centrifugation, and depth filtration (normal flow filtration). Historically vaccine harvest clarification was usually achieved by centrifugation followed by depth filtration. Recently membrane based technologies have gained prominence in vaccine clarification. The increasing use of single-use technologies in upstream processes necessitated a shift in harvest strategies. This review offers a comprehensive view on different membrane based technologies and their application in vaccine clarification, outlines the challenges involved and presents the current state of best practices in the clarification of vaccines. Copyright © 2015 Elsevier Inc. All rights reserved.

Plant lesions promote the rapid multiplication of Escherichia coli O157:H7 on post-harvest lettuce

USDA-ARS?s Scientific Manuscript database

Several outbreaks of Escherichia coli O157:H7 (EcO157) infections have been associated with minimally processed leafy vegetables in the U.S. Harvesting and processing cause plant tissue damage. In order to assess the role of plant tissue damage in the contamination of leafy greens with EcO157, the e...

78 FR 21071 - Fisheries of the Northeastern United States; Atlantic Herring Fishery; Sub-ACL (Annual Catch...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-04-09

...-ACL (Annual Catch Limit) Harvested for Management Area 2 AGENCY: National Marine Fisheries Service... limit (ACL), optimum yield, domestic harvest and processing, U.S. at-sea processing, border transfer...); the 2013 sub-ACL allocated to Area 2 is 22,146 mt, and 0 mt of the sub-ACL is set aside for research...

Cost and productivity of new technology for harvesting and in-woods processing small-diameter trees.

Treesearch

Michael B Lambert; James O. Howard

1990-01-01

A study was conducted on the productivity and cost of an integrated harvesting and processing system operating in small-diameter timber (western hemlock-type) on the Olympic Peninsula of western Washington. The system uses a new steep-slope fellerbuncher, a clam-bunk grapple-skidder (forwarder), a prototype chain-flail debarker delimber, a chipper, a conveyor system,...

Human-induced evolution caused by unnatural selection through harvest of wild animals

PubMed Central

Allendorf, Fred W.; Hard, Jeffrey J.

2009-01-01

Human harvest of phenotypically desirable animals from wild populations imposes selection that can reduce the frequencies of those desirable phenotypes. Hunting and fishing contrast with agricultural and aquacultural practices in which the most desirable animals are typically bred with the specific goal of increasing the frequency of desirable phenotypes. We consider the potential effects of harvest on the genetics and sustainability of wild populations. We also consider how harvesting could affect the mating system and thereby modify sexual selection in a way that might affect recruitment. Determining whether phenotypic changes in harvested populations are due to evolution, rather than phenotypic plasticity or environmental variation, has been problematic. Nevertheless, it is likely that some undesirable changes observed over time in exploited populations (e.g., reduced body size, earlier sexual maturity, reduced antler size, etc.) are due to selection against desirable phenotypes—a process we call “unnatural” selection. Evolution brought about by human harvest might greatly increase the time required for over-harvested populations to recover once harvest is curtailed because harvesting often creates strong selection differentials, whereas curtailing harvest will often result in less intense selection in the opposing direction. We strongly encourage those responsible for managing harvested wild populations to take into account possible selective effects of harvest management and to implement monitoring programs to detect exploitation-induced selection before it seriously impacts viability. PMID:19528656

Challenges for Planning and Maintaining of Urban Rain Harvesting Systems- the case of Hammarby Sjöstad and Årstafältet in Stockholm

NASA Astrophysics Data System (ADS)

Suleiman, Lina

2017-04-01

Planners and policymakers' concern escalates over conventional systems dealing with rains in cities based on domination and control of nature rather than harmony and design with nature. A new spatial planning paradigm is needed to put in place systems which mimic natural water systems and promise multiple values instead of systems consider rain as a source of problem. However, such approach embodies significant planning challenges. Urban rain harvesting systems (URHs) are inherently viewed as 'sociotechnical' systems. As such, planning processes should consider the interdependence of 'social' and 'technical' aspects as essential elements if a transition towards sustainable urban water systems is to be realised. Drawing on a common understanding for what urban rain harvesting systems should deliver in terms of 'functions' and 'added values', a generic planning framework is developed to inform practitioners on how the 'socio' and 'technical' elements should be assimilated in a long-term and integrated planning processes of URHs. Using the developed framework, the paper examines the planning and maintenance processes of urban rain harvesting systems in Årstafältet and Hammarby Sjöstad respectively. Results show that planners lack a common operational understanding on how these systems should be designed holistically in a long term and integrated planning processes creating working gabs or positional conflicts. In practice, urban planners and water engineers look at these systems as either urban design component or water drainage system to deal with technical functions hindering a smooth transition path towards urban rain harvesting systems. The paper concludes on the urgency for reordering roles and relations within a new set-up organisation to incubate these systems in long-term planning and maintenance processes. Key words: 'Sociotechnical' system, Water, Planning, Urban Rain Harvesting systems (URHs), Hammarby Sjostad and Årstafältet

Conditions and limitations on learning in the adaptive management of mallard harvests

USGS Publications Warehouse

Johnson, F.A.; Kendall, W.L.; Dubovsky, J.A.

2002-01-01

In 1995, the United States Fish and Wildlife Service adopted a protocol for the adaptive management of waterfowl hunting regulations (AHM) to help reduce uncertainty about the magnitude of sustainable harvests. To date, the AHM process has focused principally on the midcontinent population of mallards (Anas platyrhynchos), whose dynamics are described by 4 alternative models. Collectively, these models express uncertainty (or disagreement) about whether harvest is an additive or a compensatory form of mortality and whether the reproductive process is weakly or strongly density-dependent. Each model is associated with a probability or 'weight,' which describes its relative ability to predict changes in population size. These Bayesian probabilities are updated annually using a comparison of population size predicted under each model with that observed by a monitoring program. The current AHM process is passively adaptive, in the sense that there is no a priori consideration of how harvest decisions might affect discrimination among models. We contrast this approach with an actively adaptive approach, in which harvest decisions are used in part to produce the learning needed to increase long-term management performance. Our investigation suggests that the passive approach is expected to perform nearly as well as an optimal actively adaptive approach, particularly considering the nature of the model set, management objectives and constraints, and current regulatory alternatives. We offer some comments about the nature of the biological hypotheses being tested and describe some of the inherent limitations on learning in the AHM process.

Structured decision making as a framework for large-scale wildlife harvest management decisions

USGS Publications Warehouse

Robinson, Kelly F.; Fuller, Angela K.; Hurst, Jeremy E.; Swift, Bryan L.; Kirsch, Arthur; Farquhar, James F.; Decker, Daniel J.; Siemer, William F.

2016-01-01

Fish and wildlife harvest management at large spatial scales often involves making complex decisions with multiple objectives and difficult tradeoffs, population demographics that vary spatially, competing stakeholder values, and uncertainties that might affect management decisions. Structured decision making (SDM) provides a formal decision analytic framework for evaluating difficult decisions by breaking decisions into component parts and separating the values of stakeholders from the scientific evaluation of management actions and uncertainty. The result is a rigorous, transparent, and values-driven process. This decision-aiding process provides the decision maker with a more complete understanding of the problem and the effects of potential management actions on stakeholder values, as well as how key uncertainties can affect the decision. We use a case study to illustrate how SDM can be used as a decision-aiding tool for management decision making at large scales. We evaluated alternative white-tailed deer (Odocoileus virginianus) buck-harvest regulations in New York designed to reduce harvest of yearling bucks, taking into consideration the values of the state wildlife agency responsible for managing deer, as well as deer hunters. We incorporated tradeoffs about social, ecological, and economic management concerns throughout the state. Based on the outcomes of predictive models, expert elicitation, and hunter surveys, the SDM process identified management alternatives that optimized competing objectives. The SDM process provided biologists and managers insight about aspects of the buck-harvest decision that helped them adopt a management strategy most compatible with diverse hunter values and management concerns.

Energy harvesting: an integrated view of materials, devices and applications.

PubMed

Radousky, H B; Liang, H

2012-12-21

Energy harvesting refers to the set of processes by which useful energy is captured from waste, environmental, or mechanical sources and is converted into a usable form. The discipline of energy harvesting is a broad topic that includes established methods and materials such as photovoltaics and thermoelectrics, as well as more recent technologies that convert mechanical energy, magnetic energy and waste heat to electricity. This article will review various state-of-the-art materials and devices for direct energy conversion and in particular will include multistep energy conversion approaches. The article will highlight the nano-materials science underlying energy harvesting principles and devices, but also include more traditional bulk processes and devices as appropriate and synergistic. Emphasis is placed on device-design innovations that lead to higher efficiency energy harvesting or conversion technologies ranging from the cm/mm-scale down to MEMS/NEMS (micro- and nano-electromechanical systems) devices. Theoretical studies are reviewed, which address transport properties, crystal chemistry, thermodynamic analysis, energy transfer, system efficiency and device operation. New developments in experimental methods; device design and fabrication; nanostructured materials fabrication; materials properties; and device performance measurement techniques are discussed.

Energy harvesting: an integrated view of materials, devices and applications

NASA Astrophysics Data System (ADS)

Radousky, H. B.; Liang, H.

2012-12-01

Energy harvesting refers to the set of processes by which useful energy is captured from waste, environmental, or mechanical sources and is converted into a usable form. The discipline of energy harvesting is a broad topic that includes established methods and materials such as photovoltaics and thermoelectrics, as well as more recent technologies that convert mechanical energy, magnetic energy and waste heat to electricity. This article will review various state-of-the-art materials and devices for direct energy conversion and in particular will include multistep energy conversion approaches. The article will highlight the nano-materials science underlying energy harvesting principles and devices, but also include more traditional bulk processes and devices as appropriate and synergistic. Emphasis is placed on device-design innovations that lead to higher efficiency energy harvesting or conversion technologies ranging from the cm/mm-scale down to MEMS/NEMS (micro- and nano-electromechanical systems) devices. Theoretical studies are reviewed, which address transport properties, crystal chemistry, thermodynamic analysis, energy transfer, system efficiency and device operation. New developments in experimental methods; device design and fabrication; nanostructured materials fabrication; materials properties; and device performance measurement techniques are discussed.

Harvesting Effects, Recovery Mechanisms, and Management Strategies for a Long-Lived and Structural Precious Coral

PubMed Central

Montero-Serra, Ignasi; Linares, Cristina; García, Marina; Pancaldi, Francesca; Frleta-Valić, Maša; Ledoux, Jean-Baptiste; Zuberer, Frederic; Merad, Djamel; Drap, Pierre; Garrabou, Joaquim

2015-01-01

Overexploitation is a major threat for the integrity of marine ecosystems. Understanding the ecological consequences of different extractive practices and the mechanisms underlying the recovery of populations is essential to ensure sustainable management plans. Precious corals are long-lived structural invertebrates, historically overfished, and their conservation is currently a worldwide concern. However, the processes underlying their recovery are poorly known. Here, we examined harvesting effects and recovery mechanisms of red coral Corallium rubrum by analyzing long-term photographic series taken on two populations that were harvested. We compared the relative importance of reproduction and re-growth as drivers of resilience. Harvesting heavily impacted coral populations causing large decreases in biomass and strong size-class distribution shifts towards populations dominated by small colonies. At the end of the study (after 4 and 7 years) only partial recovery was observed. The observed general pattern of low recruitment and high mortality of new recruits demonstrated limited effects of reproduction on population recovery. Adversely, low mortality of partially harvested adults and a large proportion of colonies showing new branches highlighted the importance of re-growth in the recovery process. The demographic projections obtained through stochastic models confirmed that the recovery rates of C. rubrum can be strongly modulated depending on harvesting procedures. Thus, leaving the basal section of the colonies when harvesting to avoid total mortality largely enhances the resilience of C. rubrum populations and quickens their recovery. On the other hand, the high survival of harvested colonies and the significant biomass reduction indicated that abundance may not be an adequate metric to assess the conservation status of clonal organisms because it can underestimate harvesting effects. This study highlights the unsustainability of current harvesting practices of C. rubrum and provides urgently needed data to improve management practices that are still largely based on untested assumptions. PMID:25706556

Influence of grape density and harvest date on changes in phenolic composition, phenol extractability indices, and instrumental texture properties during ripening.

PubMed

Rolle, Luca; Segade, Susana Río; Torchio, Fabrizio; Giacosa, Simone; Cagnasso, Enzo; Marengo, Fabio; Gerbi, Vincenzo

2011-08-24

Changes in the phenolic composition, phenol extractability indices, and mechanical properties occur in grape berries during the ripening process, but the heterogeneity of the grapes harvested at different ripening stages affects the reliability of the results obtained. In this work, these changes were studied in Nebbiolo grapes harvested during five consecutive weeks and then separated according to three density classes. The changes observed in chemical and mechanical parameters through the ripening process are more related to berry density than harvest date. Therefore, the winemaker has to select the flotation density according to the objective quality properties of the wine to be elaborated. On the other hand, the stiffer grapes were associated with a higher accumulation of proanthocyanidins. The harder grapes provided the higher concentration and extractability of flavanols reactive to vanillin, whereas the thicker ones facilitated the extraction of proanthocyanidins.

Where do the logs go after harvest? A look at the role of hardwood exports

Treesearch

Matt Bumgardner

2017-01-01

If you have recently harvested timber, a question you might have is, "Where did the logs go after they left my woodland?" Most likely, they were processed somewhere in the United States. Just over 2.3% of the total hardwood log volume harvested in the U.S. was exported in 2014, the latest year for which data are available. Considering only the higher value...

Fabrication and Characterization of Bi2Te3-Based Chip-Scale Thermoelectric Energy Harvesting Devices

NASA Astrophysics Data System (ADS)

Cornett, Jane; Chen, Baoxing; Haidar, Samer; Berney, Helen; McGuinness, Pat; Lane, Bill; Gao, Yuan; He, Yifan; Sun, Nian; Dunham, Marc; Asheghi, Mehdi; Goodson, Ken; Yuan, Yi; Najafi, Khalil

2017-05-01

Thermoelectric energy harvesters convert otherwise wasted heat into electrical energy. As a result, they have the potential to play a critical role in the autonomous wireless sensor network signal chain. In this paper, we present work carried out on the development of Bi2Te3-based thermoelectric chip-scale energy harvesting devices. Process flow, device demonstration and characterization are highlighted.

Productivity and cost of the ponsse 15-series, cust-to-length harvesting systems in southern pine plantations

Treesearch

Robert A. Tufts

1997-01-01

Machine productivity data were collected for a Ponsse HS-15 harvester and S-15 forwarder from study sites in central Alabama during a second thinning. Tree size, in terms of diameter at breast height and volume, and the number of pieces processed per tree, were the variables with the greatest impact on harvester productivity. The distance fiom the machine to the tree...

Estimates of Nutrient Drain by Dormant-Season Harvests of Coppice American Sycamore

Treesearch

B.G. Blackmon

1979-01-01

Estimates of the amount of nutrients removed by dormant-season harvests of coppice American sycamore indicated that harvesting once (at age 4) or twice (at ages 2 and 4) removed 20-145 kg/ha of N, P, K, Ca, and Mg and small quantities of Mn, Zn, Fe, and Cu. Calculations of nutrient drain indicated that for N, gains through natural processes about equal losses, but...

Dark States in the Light-Harvesting complex 2 Revealed by Two-dimensional Electronic Spectroscopy

PubMed Central

Ferretti, Marco; Hendrikx, Ruud; Romero, Elisabet; Southall, June; Cogdell, Richard J.; Novoderezhkin, Vladimir I.; Scholes, Gregory D.; van Grondelle, Rienk

2016-01-01

Energy transfer and trapping in the light harvesting antennae of purple photosynthetic bacteria is an ultrafast process, which occurs with a quantum efficiency close to unity. However the mechanisms behind this process have not yet been fully understood. Recently it was proposed that low-lying energy dark states, such as charge transfer states and polaron pairs, play an important role in the dynamics and directionality of energy transfer. However, it is difficult to directly detect those states because of their small transition dipole moment and overlap with the B850/B870 exciton bands. Here we present a new experimental approach, which combines the selectivity of two-dimensional electronic spectroscopy with the availability of genetically modified light harvesting complexes, to reveal the presence of those dark states in both the genetically modified and the wild-type light harvesting 2 complexes of Rhodopseudomonas palustris. We suggest that Nature has used the unavoidable charge transfer processes that occur when LH pigments are concentrated to enhance and direct the flow of energy. PMID:26857477

Harvesting of Chlorella sorokiniana by co-culture with the filamentous fungus Isaria fumosorosea: A potential sustainable feedstock for hydrothermal gasification.

PubMed

Mackay, Stephen; Gomes, Eduardo; Holliger, Christof; Bauer, Rolene; Schwitzguébel, Jean-Paul

2015-06-01

Despite recent advances in down-stream processing, production of microalgae remains substantially limited because of economical reasons. Harvesting and dewatering are the most energy-intensive processing steps in their production and contribute 20-30% of total operational cost. Bio-flocculation of microalgae by co-cultivation with filamentous fungi relies on the development of large structures that facilitate cost effective harvesting. A yet unknown filamentous fungus was isolated as a contaminant from a microalgal culture and identified as Isaria fumosorosea. Blastospores production was optimized in minimal medium and the development of pellets, possibly lichens, was followed when co-cultured with Chlorella sorokiniana under strict autotrophic conditions. Stable pellets (1-2mm) formed rapidly at pH 7-8, clearing the medium of free algal cells. Biomass was harvested with large inexpensive filters, generating wet slurry suitable for hydrothermal gasification. Nutrient rich brine from the aqueous phase of hydrothermal gasification supported growth of the fungus and may increase the process sustainability. Copyright © 2015 Elsevier Ltd. All rights reserved.

Evaluation of operating conditions for sustainable harvesting of microalgal biomass applying electrochemical method using non sacrificial electrodes.

PubMed

Misra, Rohit; Guldhe, Abhishek; Singh, Poonam; Rawat, Ismail; Stenström, Thor Axel; Bux, Faizal

2015-01-01

The efficient harvesting of microalgae is considered to be one of the challenging steps of algal biofuel production and a key factor limiting the commercial use of microalgae. To overcome the limitation of metallic electrodes depletion, the application of non-sacrificial electrode was investigated for the electrochemical harvesting (ECH) of microalgae. The effect of applied current, addition of electrolyte and initial pH were parameters investigated. The highest recovery efficiency of 83% was obtained for Scenedesmus obliquus at 1.5A, initial pH 9 and 6gL(-)(1) NaCl with power consumption of 3.84kWhkg(-)(1). Recovery efficiency of ECH process was comparable to literature reported centrifugation, filtration and chemical flocculation techniques but with a much lower power consumption. The ECH process with addition of electrolyte enhanced the lipid extraction by 22% without any adverse effects. The ECH process with non sacrificial carbon electrodes could be a possible harvesting step at commercial scale microalgal biomass production. Copyright © 2014 Elsevier Ltd. All rights reserved.

Dark States in the Light-Harvesting complex 2 Revealed by Two-dimensional Electronic Spectroscopy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ferretti, Marco; Hendrikx, Ruud; Romero, Elisabet

Energy transfer and trapping in the light harvesting antennae of purple photosynthetic bacteria is an ultrafast process, which occurs with a quantum efficiency close to unity. However the mechanisms behind this process have not yet been fully understood. Recently it was proposed that low-lying energy dark states, such as charge transfer states and polaron pairs, play an important role in the dynamics and directionality of energy transfer. However, it is difficult to directly detect those states because of their small transition dipole moment and overlap with the B850/B870 exciton bands. Here we present a new experimental approach, which combines themore » selectivity of two-dimensional electronic spectroscopy with the availability of genetically modified light harvesting complexes, to reveal the presence of those dark states in both the genetically modified and the wild-type light harvesting 2 complexes of Rhodopseudomonas palustris. In conclusion, we suggest that Nature has used the unavoidable charge transfer processes that occur when LH pigments are concentrated to enhance and direct the flow of energy.« less

Dark States in the Light-Harvesting complex 2 Revealed by Two-dimensional Electronic Spectroscopy

DOE PAGES

Ferretti, Marco; Hendrikx, Ruud; Romero, Elisabet; ...

2016-02-09

Energy transfer and trapping in the light harvesting antennae of purple photosynthetic bacteria is an ultrafast process, which occurs with a quantum efficiency close to unity. However the mechanisms behind this process have not yet been fully understood. Recently it was proposed that low-lying energy dark states, such as charge transfer states and polaron pairs, play an important role in the dynamics and directionality of energy transfer. However, it is difficult to directly detect those states because of their small transition dipole moment and overlap with the B850/B870 exciton bands. Here we present a new experimental approach, which combines themore » selectivity of two-dimensional electronic spectroscopy with the availability of genetically modified light harvesting complexes, to reveal the presence of those dark states in both the genetically modified and the wild-type light harvesting 2 complexes of Rhodopseudomonas palustris. In conclusion, we suggest that Nature has used the unavoidable charge transfer processes that occur when LH pigments are concentrated to enhance and direct the flow of energy.« less

Effect of Liberibacter infection (huanglongbing or "greening" disease) of citrus on orange juice flavor quality by sensory evaluation.

PubMed

Plotto, Anne; Baldwin, Elizabeth; McCollum, Greg; Manthey, John; Narciso, Jan; Irey, Mike

2010-05-01

Some anecdotal reports suggest that infection of citrus trees with Candidatus Liberibacter asiaticus (Las), the suspected causal agent of huanglongbing (HLB) disease, imparts off flavor to orange juice. It is of interest to the industry to know how Las infection affects juice quality with respect to cultivar, maturity, or processing method. Hamlin, Midsweet, and Valencia oranges were harvested over 2 y from trees that tested negative (Las-) or positive (Las+) for Las from different groves and included normal looking (nonsymptomatic) and symptomatic fruit (small, green, and lopsided) from Las+ trees. In the 1st year, fruit were manually juiced, while in the 2nd year, a commercial process was used. Juice from Las+ trees was compared to juice from Las- trees in difference-from-control tests, and by descriptive analysis. Results showed large variability due to tree, harvest date, and cultivar. Juice from Hamlin Las+ trees tended to be more bitter and sour than its Las- counterpart. In contrast, hand processed Valencia juice from Las+ trees was perceived to have some off-flavor and bitterness compared to control, but the following year, commercially processed Valencia juice from Las+ trees was perceived to be only slightly more sour than juice from Las- trees for the April harvest, and to be sweeter for the June harvest. When juice from individual replicates was pooled to be more representative of a commercial situation, there was no difference between Las+ and Las- juice in Valencia. Trained panel differences were noted for juice from Hamlin Las+ fruit, especially for symptomatic fruit. Assumptions that juice made from oranges harvested from Huanglongbing (from infection with Liberibacter sp.) affected trees is off-flavored appeared to be generally more true for Hamlin juice than for Midsweet or Valencia, especially for Hamlin juice made from symptomatic fruit. For Midsweet and Valencia, flavor differences between juice made from fruit harvested from diseased or healthy trees varied greatly between trees, season, and even processing method. Under a commercial processing situation, where juice is blended from several varieties, seasons, and multiple locations, it is expected that off-flavor will not be a major problem.

Control of electro-chemical processes using energy harvesting materials and devices.

PubMed

Zhang, Yan; Xie, Mengying; Adamaki, Vana; Khanbareh, Hamideh; Bowen, Chris R

2017-12-11

Energy harvesting is a topic of intense interest that aims to convert ambient forms of energy such as mechanical motion, light and heat, which are otherwise wasted, into useful energy. In many cases the energy harvester or nanogenerator converts motion, heat or light into electrical energy, which is subsequently rectified and stored within capacitors for applications such as wireless and self-powered sensors or low-power electronics. This review covers the new and emerging area that aims to directly couple energy harvesting materials and devices with electro-chemical systems. The harvesting approaches to be covered include pyroelectric, piezoelectric, triboelectric, flexoelectric, thermoelectric and photovoltaic effects. These are used to influence a variety of electro-chemical systems such as applications related to water splitting, catalysis, corrosion protection, degradation of pollutants, disinfection of bacteria and material synthesis. Comparisons are made between the range harvesting approaches and the modes of operation are described. Future directions for the development of electro-chemical harvesting systems are highlighted and the potential for new applications and hybrid approaches are discussed.

Low-cost capacitor voltage inverter for outstanding performance in piezoelectric energy harvesting.

PubMed

Lallart, Mickaël; Garbuio, Lauric; Richard, Claude; Guyomar, Daniel

2010-01-01

The purpose of this paper is to propose a new scheme for piezoelectric energy harvesting optimization. The proposed enhancement relies on a new topology for inverting the voltage across a single capacitor with reduced losses. The increase of the inversion quality allows a much more effective energy harvesting process using the so-called synchronized switch harvesting on inductor (SSHI) nonlinear technique. It is shown that the proposed architecture, based on a 2-step inversion, increases the harvested power by a theoretical factor up to square root of 2 (i.e., 40% gain) compared with classical SSHI, allowing an increase of the harvested power by a factor greater than 1000% compared with the standard energy harvesting technique for realistic values of inversion components. The proposed circuit, using only 4 digital switches and an intermediate capacitor, is also ultra-low power, because the inversion circuit does not require any external energy and the command signals are very simple.

A Process-Based Model of TCA Cycle Functioning to Analyze Citrate Accumulation in Pre- and Post-Harvest Fruits.

PubMed

Etienne, Audrey; Génard, Michel; Bugaud, Christophe

2015-01-01

Citrate is one of the most important organic acids in many fruits and its concentration plays a critical role in organoleptic properties. The regulation of citrate accumulation throughout fruit development, and the origins of the phenotypic variability of the citrate concentration within fruit species remain to be clarified. In the present study, we developed a process-based model of citrate accumulation based on a simplified representation of the TCA cycle to predict citrate concentration in fruit pulp during the pre- and post-harvest stages. Banana fruit was taken as a reference because it has the particularity of having post-harvest ripening, during which citrate concentration undergoes substantial changes. The model was calibrated and validated on the two stages, using data sets from three contrasting cultivars in terms of citrate accumulation, and incorporated different fruit load, potassium supply, and harvest dates. The model predicted the pre and post-harvest dynamics of citrate concentration with fairly good accuracy for the three cultivars. The model suggested major differences in TCA cycle functioning among cultivars during post-harvest ripening of banana, and pointed to a potential role for NAD-malic enzyme and mitochondrial malate carriers in the genotypic variability of citrate concentration. The sensitivity of citrate accumulation to growth parameters and temperature differed among cultivars during post-harvest ripening. Finally, the model can be used as a conceptual basis to study citrate accumulation in fleshy fruits and may be a powerful tool to improve our understanding of fruit acidity.

Microbial safety of fresh produce

USDA-ARS?s Scientific Manuscript database

The book entitled “Microbial Safety of Fresh Produce” with 23 chapters is divided into following six sections: Microbial contamination of fresh produce, Pre-harvest strategies, post-harvest interventions, Produce safety during processing and handling, Public, legal, and economic Perspectives, and Re...

Pine Forest Harvest Leads to Decade-Scale Alterations in Soil Fungal Communities

NASA Astrophysics Data System (ADS)

Boutton, T. W.; Mushinski, R. M.; Gentry, T. J.

2016-12-01

Forestlands provide a multitude of ecosystem services, and sustainable management is crucial to maintaining the benefits of these ecosystems. Intensive organic matter removal (OMR) of logging residues and forest litter during forest harvest may result in long-term alterations to soil properties and processes. Because fungal activity regulates essential biogeochemical processes in forestlands, changes in soil fungal community structure following OMR may translate into altered soil function. Using a replicated field experiment in southern pine forest in eastern Texas, USA, we sampled soil to a depth of 1 m to assess the impact of intensive OMR on soil fungal communities. Soils were collected from replicated (n = 3 ) loblolly pine (Pinus taeda L.) stands subjected to 3 different harvest intensities (i.e., unharvested old growth stands, bole-only harvest stands, and whole-tree harvest + forest floor removal stands) in 1997. Nearly two decades after trees were harvested and replanted, next generation sequencing of the fungal internal transcribed spacer showed the diversity and community structure of the entire fungal community was altered relative to the unharvested stands. The relative abundance of Ascomycetes increased as OMR intensity increased and was positively correlated to concurrent changes in soil pH. The community composition of fungal functional groups (e.g., ecto- and arbuscular mycorrhizal, saprophytic fungi) was also altered by OMR. The most abundant taxa, Russula exhibited significant reductions in response to increasing intensity of OMR. Results of this study illustrate a linkage between anthropogenically-induced aboveground perturbation, edaphic factors, and belowground soil fungal communities of southern pine forests. Also, these results indicate that tree harvesting effects on soil fungal communities can persist for decades post-harvest, with potential implications for soil functional characteristics.

Local bone graft harvesting and volumes in posterolateral lumbar fusion: a technical report.

PubMed

Carragee, Eugene J; Comer, Garet C; Smith, Micah W

2011-06-01

In lumbar surgery, local bone graft is often harvested and used in posterolateral fusion procedures. The volume of local bone graft available for posterolateral fusion has not been determined in North American patients. Some authors have described this as minimal, but others have suggested the volume was sufficient to be reliably used as a stand-alone bone graft substitute for single-level fusion. To describe the technique used and determine the volume of local bone graft available in a cohort of patients undergoing single-level primary posterolateral fusion by the authors harvesting technique. Technical description and cohort report. Consecutive patients undergoing lumbar posterolateral fusion with or without instrumentation for degenerative processes. Local bone graft volume. Consecutive patients undergoing lumbar posterolateral fusion with or without instrumentation for degenerative processes of were studied. Local bone graft was harvested by a standard method in each patient and the volume measured by a standard procedure. Twenty-five patients were studied, and of these 11 (44%) had a previous decompression. The mean volume of local bone graft harvested was measured to be 25 cc (range, 12-36 cc). Local bone graft was augmented by iliac crest bone in six of 25 patients (24%) if the posterolateral fusion bed was not well packed with local bone alone. There was a trend to greater local bone graft volumes in men and in patients without previous decompression. Large volumes of local bone can be harvested during posterolateral lumbar fusion surgery. Even in patients with previous decompression the volume harvested is similar to that reported harvested from the posterior iliac crest for single-level fusion. Copyright © 2011 Elsevier Inc. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cryns, Jackson W.; Hatchell, Brian K.; Santiago-Rojas, Emiliano

Formal journal article Experimental analysis of a piezoelectric energy harvesting system for harmonic, random, and sine on random vibration Abstract: Harvesting power with a piezoelectric vibration powered generator using a full-wave rectifier conditioning circuit is experimentally compared for varying sinusoidal, random and sine on random (SOR) input vibration scenarios. Additionally, the implications of source vibration characteristics on harvester design are discussed. Studies in vibration harvesting have yielded numerous alternatives for harvesting electrical energy from vibrations but piezoceramics arose as the most compact, energy dense means of energy transduction. The rise in popularity of harvesting energy from ambient vibrations has mademore » piezoelectric generators commercially available. Much of the available literature focuses on maximizing harvested power through nonlinear processing circuits that require accurate knowledge of generator internal mechanical and electrical characteristics and idealization of the input vibration source, which cannot be assumed in general application. In this manuscript, variations in source vibration and load resistance are explored for a commercially available piezoelectric generator. We characterize the source vibration by its acceleration response for repeatability and transcription to general application. The results agree with numerical and theoretical predictions for in previous literature that load optimal resistance varies with transducer natural frequency and source type, and the findings demonstrate that significant gains are seen with lower tuned transducer natural frequencies for similar source amplitudes. Going beyond idealized steady state sinusoidal and simplified random vibration input, SOR testing allows for more accurate representation of real world ambient vibration. It is shown that characteristic interactions from more complex vibrational sources significantly alter power generation and power processing requirements by increasing harvested power, shifting optimal conditioning impedance, inducing significant voltage supply fluctuations and ultimately rendering idealized sinusoidal and random analyses insufficient.« less

Salmonella, Escherichia coli and Enterobacteriaceae in the peanut supply chain: From farm to table.

PubMed

Nascimento, M S; Carminati, J A; Silva, I C R N; Silva, D L; Bernardi, A O; Copetti, M V

2018-03-01

Due to recent foodborne outbreaks, peanuts have been considered a potential risk for Salmonella transmission. For this reason, the aim of this study was to determine the prevalence and contamination load of Salmonella, Escherichia coli and Enterobacteriaceae throughout the peanut supply chain in Brazil. Samples of peanuts and peanut-containing processed products from post-harvest (n=129), secondary processing (n=185) and retail market (n=100) were analyzed. The results showed high Enterobacteriaceae counts in the post-harvest samples. At the end of the secondary processing, 16% of the samples remained contaminated by this group of microorganisms. Six peanut samples from primary production and one sample of peanut butter were tested positive for E. coli while Salmonella was detected in nine samples (2.2%): six from post-harvest, two from the initial stage of the secondary processing and one from retail. The Salmonella counts ranged between 0.004 and 0.092MPN/g and five serotypes were identified (Muenster, Miami, Javiana, Oranienburg, Glostrup). The results demonstrated a high prevalence of Enterobacteriaceae and low prevalence of E. coli throughout the peanut supply chain. Furthermore, it was verified that peanuts may become contaminated by Salmonella during different stages of the supply chain, especially at post-harvest. Copyright © 2017 Elsevier Ltd. All rights reserved.

Harvesting microalgae cultures with superabsorbent polymers: desulfurization of Chlamydomonas reinhardtii for hydrogen production.

PubMed

Martín del Campo, Julia S; Patiño, Rodrigo

2013-12-01

It is presented in this work a new methodology to harvest fresh water microalgae cultures by extracting the culture medium with superabsorbent polymers (SAPs). The microalgae Chlamydomonas reinhardtii were grown in the Sueoka culture medium, harvested with polyacrylic SAPs and re-suspended in the culture medium tris-acetate-potassium without sulfur (TAP-S) to generate hydrogen (H2 ) under anoxic conditions. The H2 production as an alternative fuel is relevant since this gas has high-energy recovery without involving carbon. Before microalgae harvesting, a number of range diameters (1-7 mm) for SAPs spherical particles were tested, and the initial rate (V0 ) and the maximal capacity (Qmax ) were determined for the Sueoka medium absorption. The SAP particles with the diameter range 2.0-2.5 mm performed the best and these were employed for the rest of the experiments. The Sueoka medium has a high salt content and the effect of the ionic strength was also studied for different medium concentrations (0-400%). The SAPs were reused in consecutive absorption/desorption cycles, maintaining their absorption capacity. Although the Sueoka medium reduces the SAPs absorption capacity to 40% compared with deionized water, the use of SAPs was very significant for the desulfurization process of C. reihardtii. The presence of C. reinhardtii at different concentrations does not affect the absorption capacity of the Sueoka culture medium by the SAPs. In order to reduce the time of the process, an increase of the SAPs concentration was tested, being 20 g of SAP per liter of medium, a condition to harvest the microalgae culture in 4 h. There were no evident cell ruptures during the harvesting process and the cells remained alive. Finally, the harvested biomass was re-suspended in TAP-S medium and kept under anaerobic conditions and illumination to produce H2 that was monitored by a PEM fuel cell. The use of SAPs for microalgae harvesting is a feasible non-invasive procedure to obtain high concentrations of functional biomass at low cost; it offers an attractive alternative due to its versatility and simplicity. © 2013 Wiley Periodicals, Inc.

Effects of harvesting flowers from shrubs on the persistence and abundance of wild shrub populations at multiple spatial extents.

PubMed

Cabral, Juliano Sarmento; Bond, William J; Midgley, Guy F; Rebelo, Anthony G; Thuiller, Wilfried; Schurr, Frank M

2011-02-01

Wildflower harvesting is an economically important activity of which the ecological effects are poorly understood. We assessed how harvesting of flowers affects shrub persistence and abundance at multiple spatial extents. To this end, we built a process-based model to examine the mean persistence and abundance of wild shrubs whose flowers are subject to harvest (serotinous Proteaceae in the South African Cape Floristic Region). First, we conducted a general sensitivity analysis of how harvesting affects persistence and abundance at nested spatial extents. For most spatial extents and combinations of demographic parameters, persistence and abundance of flowering shrubs decreased abruptly once harvesting rate exceeded a certain threshold. At larger extents, metapopulations supported higher harvesting rates before their persistence and abundance decreased, but persistence and abundance also decreased more abruptly due to harvesting than at smaller extents. This threshold rate of harvest varied with species' dispersal ability, maximum reproductive rate, adult mortality, probability of extirpation or local extinction, strength of Allee effects, and carrying capacity. Moreover, spatial extent interacted with Allee effects and probability of extirpation because both these demographic properties affected the response of local populations to harvesting more strongly than they affected the response of metapopulations. Subsequently, we simulated the effects of harvesting on three Cape Floristic Region Proteaceae species and found that these species reacted differently to harvesting, but their persistence and abundance decreased at low rates of harvest. Our estimates of harvesting rates at maximum sustainable yield differed from those of previous investigations, perhaps because researchers used different estimates of demographic parameters, models of population dynamics, and spatial extent than we did. Good demographic knowledge and careful identification of the spatial extent of interest increases confidence in assessments and monitoring of the effects of harvesting. Our general sensitivity analysis improved understanding of harvesting effects on metapopulation dynamics and allowed qualitative assessment of the probability of extirpation of poorly studied species. ©2010 Society for Conservation Biology.

Human enteric pathogen internalization by root uptake into food crops

USDA-ARS?s Scientific Manuscript database

With an increasing number of outbreaks and illnesses associated with pre-harvest contaminated produce, understanding the potential and mechanisms of produce contamination by enteric pathogens can aid in the development of preventative measures and post-harvest processing to reduce microbial populati...

Breeding highbush blueberry cultivars adapted to machine harvest for the fresh market

USDA-ARS?s Scientific Manuscript database

In recent years, world blueberry production has been split evenly between processing and fresh fruit markets. Machine harvest of highbush blueberry [northern highbush (NHB, Vaccinium corymbosum L.), southern highbush (SHB, Vaccinium corymbosum interspecific hybrids), and rabbiteye (RE, Vaccinium vi...

Catchment hydrological responses to forest harvest amount and spatial pattern

EPA Science Inventory

Forest harvest effects on streamflow dynamics have been well described experimentally, but a clear understanding of process-level hydrological controls can be difficult to ascertain from data alone. We apply a new model, Visualizing Ecosystems for Land Management Assessments (VE...

Distinguishing values from science in decision making: Setting harvest quotas for mountain lions in Montana

USGS Publications Warehouse

Mitchell, Michael S.; Cooley, Hilary; Gude, Justin A.; Kolbe, Jay; Nowak, J. Joshua; Proffitt, Kelly M.; Sells, Sarah N.; Thompson, Mike

2018-01-01

The relative roles of science and human values can be difficult to distinguish when informal processes are used to make complex and contentious decisions in wildlife management. Structured Decision Making (SDM) offers a formal process for making such decisions, where scientific results and concepts can be disentangled from the values of differing stakeholders. We used SDM to formally integrate science and human values for a citizen working group of ungulate hunting advocates, lion hunting advocates, and outfitters convened to address the contentious allocation of harvest quotas for mountain lions (Puma concolor) in west‐central Montana, USA, during 2014. A science team consisting of mountain lion biologists and population ecologists convened to support the working group. The science team used integrated population models that incorporated 4 estimates of mountain lion density to estimate population trajectories for 5 alternative harvest quotas developed by the working group. Results of the modeling predicted that effects of each harvest quota were consistent across the 4 density estimates; harvest quotas affected predicted population trajectories for 5 years after implementation but differences were not strong. Based on these results, the focus of the working group changed to differences in values among stakeholders that were the true impediment to allocating harvest quotas. By distinguishing roles of science and human values in this process, the working group was able to collaboratively recommend a compromise solution. This solution differed little from the status quo that had been the focus of debate, but the SDM process produced understanding and buy‐in among stakeholders involved, reducing disagreements, misunderstanding, and unproductive arguments founded on informal application of scientific data and concepts. Whereas investments involved in conducting SDM may be unnecessary for many decisions in wildlife management, the investment may be beneficial for complex, contentious, and multiobjective decisions that integrate science and human values.

Analysis of single-degree-of-freedom piezoelectric energy harvester with stopper by incremental harmonic balance method

NASA Astrophysics Data System (ADS)

Zhao, Dan; Wang, Xiaoman; Cheng, Yuan; Liu, Shaogang; Wu, Yanhong; Chai, Liqin; Liu, Yang; Cheng, Qianju

2018-05-01

Piecewise-linear structure can effectively broaden the working frequency band of the piezoelectric energy harvester, and improvement of its research can promote the practical process of energy collection device to meet the requirements for powering microelectronic components. In this paper, the incremental harmonic balance (IHB) method is introduced for the complicated and difficult analysis process of the piezoelectric energy harvester to solve these problems. After obtaining the nonlinear dynamic equation of the single-degree-of-freedom piecewise-linear energy harvester by mathematical modeling and the equation is solved based on the IHB method, the theoretical amplitude-frequency curve of open-circuit voltage is achieved. Under 0.2 g harmonic excitation, a piecewise-linear energy harvester is experimentally tested by unidirectional frequency-increasing scanning. The results demonstrate that the theoretical and experimental amplitudes have the same trend, and the width of the working band with high voltage output are 4.9 Hz and 4.7 Hz, respectively, and the relative error is 4.08%. The open-output peak voltage are 21.53 V and 18.25 V, respectively, and the relative error is 15.23%. Since the theoretical value is consistent with the experimental results, the theoretical model and the incremental harmonic balance method used in this paper are suitable for solving single-degree-of-freedom piecewise-linear piezoelectric energy harvester and can be applied to further parameter optimized design.

Parameter study and optimization for piezoelectric energy harvester for TPMS considering speed variation

NASA Astrophysics Data System (ADS)

Toghi Eshghi, Amin; Lee, Soobum; Lee, Hanmin; Kim, Young-Cheol

2016-04-01

In this paper, we perform design parameter study and design optimization for a piezoelectric energy harvester considering vehicle speed variation. Initially, a FEM model using ANSYS is developed to appraise the performance of a piezoelectric harvester in a rotating tire. The energy harvester proposed here uses the vertical deformation at contact patch area from the car weight and centrifugal acceleration. This harvester is composed of a beam which is clamped at both ends and a piezoelectric material is attached on the top of that. The piezoelectric material possesses the 31 mode of transduction in which the direction of applied field is perpendicular to that of the electric field. To optimize the harvester performance, we would change the geometrical parameters of the harvester to obtain the maximum power. One of the main challenges in the design process is obtaining the required power while considering the constraints for harvester weight and volume. These two concerns are addressed in this paper. Since the final goal of this study is the development of an energy harvester with a wireless sensor system installed in a real car, the real time data for varied velocity of a vehicle are taken into account for power measurements. This study concludes that the proposed design is applicable to wireless tire sensor systems.

Tree Species Composition and Harvest Intensity Affect Herbivore Density and Leaf Damage on Beech, Fagus sylvatica, in Different Landscape Contexts

PubMed Central

Mangels, Jule; Blüthgen, Nico; Frank, Kevin; Grassein, Fabrice; Hilpert, Andrea; Mody, Karsten

2015-01-01

Most forests are exposed to anthropogenic management activities that affect tree species composition and natural ecosystem processes. Changes in ecosystem processes such as herbivory depend on management intensity, and on regional environmental conditions and species pools. Whereas influences of specific forest management measures have already been addressed for different herbivore taxa on a local scale, studies considering effects of different aspects of forest management across different regions are rare. We assessed the influence of tree species composition and intensity of harvesting activities on arthropod herbivores and herbivore-related damage to beech trees, Fagus sylvatica, in 48 forest plots in three regions of Germany. We found that herbivore abundance and damage to beech trees differed between regions and that – despite the regional differences - density of tree-associated arthropod taxa and herbivore damage were consistently affected by tree species composition and harvest intensity. Specifically, overall herbivore damage to beech trees increased with increasing dominance of beech trees – suggesting the action of associational resistance processes – and decreased with harvest intensity. The density of leaf chewers and mines was positively related to leaf damage, and several arthropod groups responded to beech dominance and harvest intensity. The distribution of damage patterns was consistent with a vertical shift of herbivores to higher crown layers during the season and with higher beech dominance. By linking quantitative data on arthropod herbivore abundance and herbivory with tree species composition and harvesting activity in a wide variety of beech forests, our study helps to better understand the influence of forest management on interactions between a naturally dominant deciduous forest tree and arthropod herbivores. PMID:25938417

Microalgae harvesting techniques: A review.

PubMed

Singh, Gulab; Patidar, S K

2018-07-01

Microalgae with wide range of commercial applications have attracted a lot of attention of the researchers in the last few decades. However, microalgae utilization is not economically sustainable due to high cost of harvesting. A wide range of solid - liquid separation techniques are available for microalgae harvesting. The techniques include coagulation and flocculation, flotation, centrifugation and filtration or a combination of various techniques. Despite the importance of harvesting to the economics and energy balance, there is no universal harvesting technique for microalgae. Therefore, this review focuses on assessing technical, economical and application potential of various harvesting techniques so as to allow selection of an appropriate technology for cost effectively harvesting of microalgae from their culture medium. Various harvesting and concentrating techniques of microalgae were reviewed to suggest order of suitability of the techniques for four main microalgae applications i.e biofuel, human and animal food, high valued products, and water quality restoration. For deciding the order of suitability, a comparative analysis of various harvesting techniques based on the six common criterions (i.e biomass quality, cost, biomass quantity, processing time, species specific and toxicity) has been done. Based on the order of various techniques vis-a-vis various criteria and preferred order of criteria for various applications, order of suitability of harvesting techniques for various applications has been decided. Among various harvesting techniques, coagulation and flocculation, centrifugation and filtration were found to be most suitable for considered applications. These techniques may be used alone or in combination for increasing the harvesting efficiency. Copyright © 2018 Elsevier Ltd. All rights reserved.

Ecological impacts of energy-wood harvests: lessons from whole-tree harvesting and natural disturbance

USGS Publications Warehouse

Berger, Alaina L.; Palik, Brian; D'Amato, Anthony W.; Fraver, Shawn; Bradford, John B.; Nislow, Keith H.; King, David; Brooks, Robert T.

2013-01-01

Recent interest in using forest residues and small-diameter material for biofuels is generating a renewed focus on harvesting impacts and forest sustainability. The rich legacy of research from whole-tree harvesting studies can be examined in light of this interest. Although this research largely focused on consequences for forest productivity, in particular carbon and nutrient pools, it also has relevance for examining potential consequences for biodiversity and aquatic ecosystems. This review is framed within a context of contrasting ecosystem impacts from whole-tree harvesting because it represents a high level of biomass removal. Although whole-tree harvesting does not fully use the nonmerchantable biomass available, it indicates the likely direction and magnitude of impacts that can occur through energy-wood harvesting compared with less-intensive conventional harvesting and to dynamics associated with various natural disturbances. The intent of this comparison is to gauge the degree of departure of energy-wood harvesting from less intensive conventional harvesting. The review of the literature found a gradient of increasing departure in residual structural conditions that remained in the forest when conventional and whole-tree harvesting was compared with stand-replacing natural disturbance. Important stand- and landscape-level processes were related to these structural conditions. The consequence of this departure may be especially potent because future energy-wood harvests may more completely use a greater range of forest biomass at potentially shortened rotations, creating a great need for research that explores the largely unknown scale of disturbance that may apply to our forest ecosystems.

Fabrication of Scalable Indoor Light Energy Harvester and Study for Agricultural IoT Applications

NASA Astrophysics Data System (ADS)

Watanabe, M.; Nakamura, A.; Kunii, A.; Kusano, K.; Futagawa, M.

2015-12-01

A scalable indoor light energy harvester was fabricated by microelectromechanical system (MEMS) and printing hybrid technology and evaluated for agricultural IoT applications under different environmental input power density conditions, such as outdoor farming under the sun, greenhouse farming under scattered lighting, and a plant factory under LEDs. We fabricated and evaluated a dye- sensitized-type solar cell (DSC) as a low cost and “scalable” optical harvester device. We developed a transparent conductive oxide (TCO)-less process with a honeycomb metal mesh substrate fabricated by MEMS technology. In terms of the electrical and optical properties, we achieved scalable harvester output power by cell area sizing. Second, we evaluated the dependence of the input power scalable characteristics on the input light intensity, spectrum distribution, and light inlet direction angle, because harvested environmental input power is unstable. The TiO2 fabrication relied on nanoimprint technology, which was designed for optical optimization and fabrication, and we confirmed that the harvesters are robust to a variety of environments. Finally, we studied optical energy harvesting applications for agricultural IoT systems. These scalable indoor light harvesters could be used in many applications and situations in smart agriculture.

Approaches to automated protein crystal harvesting

PubMed Central

Deller, Marc C.; Rupp, Bernhard

2014-01-01

The harvesting of protein crystals is almost always a necessary step in the determination of a protein structure using X-ray crystallographic techniques. However, protein crystals are usually fragile and susceptible to damage during the harvesting process. For this reason, protein crystal harvesting is the single step that remains entirely dependent on skilled human intervention. Automation has been implemented in the majority of other stages of the structure-determination pipeline, including cloning, expression, purification, crystallization and data collection. The gap in automation between crystallization and data collection results in a bottleneck in throughput and presents unfortunate opportunities for crystal damage. Several automated protein crystal harvesting systems have been developed, including systems utilizing microcapillaries, microtools, microgrippers, acoustic droplet ejection and optical traps. However, these systems have yet to be commonly deployed in the majority of crystallography laboratories owing to a variety of technical and cost-related issues. Automation of protein crystal harvesting remains essential for harnessing the full benefits of fourth-generation synchrotrons, free-electron lasers and microfocus beamlines. Furthermore, automation of protein crystal harvesting offers several benefits when compared with traditional manual approaches, including the ability to harvest microcrystals, improved flash-cooling procedures and increased throughput. PMID:24637746

Skin donors and human skin allografts: evaluation of an 11-year practice and discard in a referral tissue bank.

PubMed

Gaucher, Sonia; Khaznadar, Zena; Gourevitch, Jean-Claude; Jarraya, Mohamed

2016-03-01

The Saint Louis hospital tissue bank provides skin allografts to pediatric and adult burn units in the Paris area. The aim of this study was to analyze our activity during the last 11 years focusing on the reasons for skin discard. Skin is procured solely from the back of the body, which is divided into 10 zones that are harvested and processed separately. This retrospective study included all skin donors harvested between June 2002 and June 2013, representing a total of 336 donors and 2770 zones. The donors were multiorgan heart-beating donors in 91 % of cases (n = 307). The main reason for discarding harvested skin was microbial contamination, detected in 99 donors (29 %). Most contaminants were of low pathogenicity. Other reasons for discard included positive serologic tests for 2 donors [17 zones (0.61 %)], unsuitable physical skin characteristics for 3 zones (0.11 %), the donor's medical history for 53 zones (1.91 %), and technical issues with processing or distribution for 61 zones (2.2 %). In our experience, microbial contamination continues to be the main reason for discarding potential skin allografts. However, discards are limited by separate harvesting and processing of multiple zones in each donor.

Nonlinear optimization of acoustic energy harvesting using piezoelectric devices.

PubMed

Lallart, Mickaeël; Guyomar, Daniel; Richard, Claude; Petit, Lionel

2010-11-01

In the first part of the paper, a single degree-of-freedom model of a vibrating membrane with piezoelectric inserts is introduced and is initially applied to the case when a plane wave is incident with frequency close to one of the resonance frequencies. The model is a prototype of a device which converts ambient acoustical energy to electrical energy with the use of piezoelectric devices. The paper then proposes an enhancement of the energy harvesting process using a nonlinear processing of the output voltage of piezoelectric actuators, and suggests that this improves the energy conversion and reduces the sensitivity to frequency drifts. A theoretical discussion is given for the electrical power that can be expected making use of various models. This and supporting experimental results suggest that a nonlinear optimization approach allows a gain of up to 10 in harvested energy and a doubling of the bandwidth. A model is introduced in the latter part of the paper for predicting the behavior of the energy-harvesting device with changes in acoustic frequency, this model taking into account the damping effect and the frequency changes introduced by the nonlinear processes in the device.

RELIABILITY TESTING OF AN ON-HARVESTER COTTON WEIGHT MEASUREMENT SYSTEM

USDA-ARS?s Scientific Manuscript database

A system for weighing seed cotton onboard stripper harvesters was developed and installed on several producer owned and operated machines. The weight measurement system provides critical information to producers when in the process of calibrating yield monitors or conducting on-farm research. The ...

Switchgrass cultivar, yield, and nutrient removal responses to harvest timing

USDA-ARS?s Scientific Manuscript database

Finite nutrients, such as P (phosphorus) and K (potassium) are remobilized post-growing season in herbaceous feedstocks such as swichgrass (Panicum virgatum L.) as a function of environmental signaling and genotype. However, harvesting early during the maturation process may result in yield reductio...

Catchment hydro-biogeochemical response to forest harvest intensity and spatial pattern

EPA Science Inventory

We apply a new model, Visualizing Ecosystems for Land Management Assessment (VELMA), to Watershed 10 (WS10) in the H.J. Andrews Experimental Forest to simulate the effects of harvest intensity and spatial pattern on catchment hydrological and biogeochemical processes. Specificall...

Optimal harvesting of a stochastic delay tri-trophic food-chain model with Lévy jumps

NASA Astrophysics Data System (ADS)

Qiu, Hong; Deng, Wenmin

2018-02-01

In this paper, the optimal harvesting of a stochastic delay tri-trophic food-chain model with Lévy jumps is considered. We introduce two kinds of environmental perturbations in this model. One is called white noise which is continuous and is described by a stochastic integral with respect to the standard Brownian motion. And the other one is jumping noise which is modeled by a Lévy process. Under some mild assumptions, the critical values between extinction and persistent in the mean of each species are established. The sufficient and necessary criteria for the existence of optimal harvesting policy are established and the optimal harvesting effort and the maximum of sustainable yield are also obtained. We utilize the ergodic method to discuss the optimal harvesting problem. The results show that white noises and Lévy noises significantly affect the optimal harvesting policy while time delays is harmless for the optimal harvesting strategy in some cases. At last, some numerical examples are introduced to show the validity of our results.

Flexible patch composed of PZT thin-film on stainless steel foil for energy harvesting from low-frequency human motions

NASA Astrophysics Data System (ADS)

Wang, Yin Jie; Chen, Chao Ting; Chen, Jiun Jung; Yeh, Sou Peng; Wu, Wen Jong

2015-03-01

To harvest energy from human motion and generate power for the emerging wearable devices, energy harvesters are required to work at very low frequency. There are several studies based on energy harvesting through human gait, which can generate significant power. However, when wearing these kind of devices, additional effort may be required and the user may feel uncomfortable when moving. The energy harvester developed here is composed of a 10 μm PZT thin-film deposited on 50 μm thick stainless steel foil by the aerosol deposition method. The PZT layer and the stainless steel foil are both very thin, thus the patch is highly flexible. The patch can be attached on the skin to harvester power through human motions such as the expansion of the chest region while breathing. The energy harvester will first be tested with a moving stage for power output measurements. The energy density can be determined for different deformation ranges and frequencies. The fabrication processes and testing results will all be detailed in this paper.

The role of energy losses in photosynthetic light harvesting

NASA Astrophysics Data System (ADS)

Krüger, T. P. J.; van Grondelle, R.

2017-07-01

Photosynthesis operates at the bottom of the food chain to convert the energy of light into carbohydrates at a remarkable global rate of about 130 TW. Nonetheless, the overall photosynthetic process has a conversion efficiency of a few percent at best, significantly less than bottom-up photovoltaic cells. The primary photosynthetic steps, consisting of light harvesting and charge separation, are often presented as having near-unity quantum efficiency but this holds only true under ideal conditions. In this review, we discuss the importance of energy loss mechanisms to establish robustness in photosynthetic light harvesting. Thermal energy dissipation of light-harvesting complexes (LHCs) in different environments is investigated and the relationships and contrasts between concentration quenching of high pigment concentrations, photoprotection (non-photochemical quenching), quenching due to protein aggregation, and fluorescence blinking are discussed. The role of charge-transfer states in light harvesting and energy dissipation is highlighted and the importance of controlled protein structural disorder to switch the light-harvesting antennae between effective light harvesters and efficient energy quenchers is underscored. The main LHC of plants, LHCII, is used as a prime example.

[Literature review of the dispersal of transgenes from genetically modified maize].

PubMed

Ricroch, Agnès; Bergé, Jean Baptiste; Messéan, Antoine

2009-10-01

This article aims at reviewing the theoretical and experimental data published in 562 publications referring to genetically modified (GM) maize dispersal. Our choice was limited to this since in the European Union (EU), GM maize is the only GM crop currently grown commercially. The pollen dispersal of transgenic maize is due to two factors: (i) pollen-mediated gene flow; (ii) seed admixture during harvest and post-harvest processes. The pollen dispersal decreases rapidly with the distance from GM plots. Climatic and topographic factors and factors of relative density between GM and non-GM maize plots impact on the pollen dispersal. The combination of both isolation distance and flowering date between source plots and sink plots limits the adventitious presence of transgenes in non-GM plots. All publications we reviewed demonstrate that the EU 0.9% threshold is technically manageable if the measures of isolation distances as well as harvesting and post harvesting processes and fully synchronous flowering are implemented.

Origin of the Two Bands in the B800 Ring and Their Involvement in the Energy Transfer Network of Allochromatium vinosum.

PubMed

Schröter, Marco; Alcocer, Marcelo J P; Cogdell, Richard J; Kühn, Oliver; Zigmantas, Donatas

2018-03-15

Bacterial photosynthesis features robust and adaptable energy-harvesting processes in which light-harvesting proteins play a crucial role. The peripheral light-harvesting complex of the purple bacterium Allochromatium vinosum is particularly distinct, featuring a double peak structure in its B800 absorption band. Two hypotheses-not necessarily mutually exclusive-concerning the origin of this splitting have been proposed; either two distinct B800 bacteriochlorophyll site energies are involved, or an excitonic dimerization of bacteriochlorophylls within the B800 ring takes place. Through the use of two-dimensional electronic spectroscopy, we present unambiguous evidence that excitonic interaction shapes the split band. We further identify and characterize all of the energy transfer pathways within this complex by using a global kinetic fitting procedure. Our approach demonstrates how the combination of two-dimensional spectral resolution and self-consistent fitting allows for extraction of information on light-harvesting processes, which would otherwise be inaccessible due to signal congestion.

Piezoelectric microgenerators--current status and challenges.

PubMed

Kim, Hyun-Uk; Lee, Woo-Ho; Dias, H V Rasika; Priya, Shashank

2009-08-01

This manuscript reviews the developments made in design and fabrication of piezoelectric microgenerators and presents a method for making a comparative study within various vibration energy harvesting mechanisms. Current generation vibration energy harvesters have power density in the range of 0.8 microW/mm3. The manuscript also reports our results on synthesis of barium titanate (BT) thin films for MEMS (micro-electromechanical systems) based energy harvester. BT sol-gel was synthesized by aqueous process using barium acetate and titanium bis (ammonium lacto) dihydroxide with PVP (Polyvinylpyrrolidone). After optimizing the annealing temperature and time, textured BT films with 600 nm thickness were obtained on (111) Pt/Ti/SiO2 wafer. A MEMS fabrication process flow was designed to produce microcantilever chips from BT films constituting 6 cantilevers connected in series with an interdigital electrode pattern. We also present some concepts for further improvement of the power density of vibration energy harvesters by incorporating 3-D structure, magnetoelectric material, and a multimodal scheme.

The impact of stress on the health of sugar cane cutters

PubMed Central

Priuli, Roseana Mara Aredes; de Moraes, Maria Silvia; Chiaravalloti, Rafael Morais

2014-01-01

OBJECTIVE Evaluate the impact of stress on sugar cane cutters and the prevalence of physical and psychological symptoms before and after harvest. METHODS We studied 114 sugarcane cutters and 109 urban workers in the pre-harvest and 102 sugar cane cutters and 81 urban workers in the post-harvest period in the city of Mendonça, SP, Southeastern Brazil, in 2009. Data analysis was based on the frequency and percentage of the assessed symptoms of stress, using the Lipp-ISSL test (Symptoms of Stress for Adults). The data were analyzed using descriptive statistics. The Fisher Test was used to compare the variable of stress between pre- and post-harvest within the sugar cane cutter and urban worker groups. P values below 0.05 were considered significant. RESULTS Stress in sugar cane cutters increased after harvesting (34.2% pre-harvest and 46.1% post-harvest); in urban workers, stress decreased from 44.0% pre-harvest to 42.0% post-harvest. There was prevalence of the phase of resistance to stress for both groups with signs more apparent from the near-exhaustion and exhaustion phases for sugar cane cutters. After harvest, there was a tendency for the number of sugar cane cutters with symptoms of near-exhaustion (6.4%) and exhaustion (10.6%) to increase. After harvest there was a trend for the number of sugar cane cutters with physical symptoms (pre-harvest = 20.5%, post-harvest = 25.5%) and psychological symptoms (pre-harvest = 64.1%; post-harvest = 70.2%) to increase. For both groups, predominantly psychological symptoms occurred in both phases (70.2% versus 64.7%). CONCLUSIONS The work process of cutting cane can cause stress. Individual factors such as cognitive perception of the experience, self-efficacy beliefs and expectations of the employee regarding their performance can influence the understanding of the reactions in their body in face of the work. PMID:24897043

The impact of stress on the health of sugar cane cutters.

PubMed

Priuli, Roseana Mara Aredes; Moraes, Maria Silvia de; Chiaravalloti, Rafael Morais

2014-04-01

Evaluate the impact of stress on sugar cane cutters and the prevalence of physical and psychological symptoms before and after harvest. We studied 114 sugarcane cutters and 109 urban workers in the pre-harvest and 102 sugar cane cutters and 81 urban workers in the post-harvest period in the city of Mendonça, SP, Southeastern Brazil, in 2009. Data analysis was based on the frequency and percentage of the assessed symptoms of stress, using the Lipp-ISSL test (Symptoms of Stress for Adults). The data were analyzed using descriptive statistics. The Fisher Test was used to compare the variable of stress between pre- and post-harvest within the sugar cane cutter and urban worker groups. P values below 0.05 were considered significant. Stress in sugar cane cutters increased after harvesting (34.2% pre-harvest and 46.1% post-harvest); in urban workers, stress decreased from 44.0% pre-harvest to 42.0% post-harvest. There was prevalence of the phase of resistance to stress for both groups with signs more apparent from the near-exhaustion and exhaustion phases for sugar cane cutters. After harvest, there was a tendency for the number of sugar cane cutters with symptoms of near-exhaustion (6.4%) and exhaustion (10.6%) to increase. After harvest there was a trend for the number of sugar cane cutters with physical symptoms (pre-harvest = 20.5%, post-harvest = 25.5%) and psychological symptoms (pre-harvest = 64.1%; post-harvest = 70.2%) to increase. For both groups, predominantly psychological symptoms occurred in both phases (70.2% versus 64.7%). The work process of cutting cane can cause stress. Individual factors such as cognitive perception of the experience, self-efficacy beliefs and expectations of the employee regarding their performance can influence the understanding of the reactions in their body in face of the work.

Novel thick-foam ferroelectret with engineered voids for energy harvesting applications

NASA Astrophysics Data System (ADS)

Luo, Z.; Shi, J.; Beeby, S. P.

2016-11-01

This work reports a novel thick-foam ferroelectret which is designed and engineered for energy harvesting applications. We fabricated this ferroelectret foam by mixing a chemical blowing agent with a polymer solution, then used heat treatment to activate the agent and create voids in the polymer foam. The dimensions of the foam, the density and size of voids can be well controlled in the fabrication process. Therefore, this ferroelectret can be engineered into optimized structure for energy harvesting applications.

Processed eucalyptus trees as a substrate component for greenhouse crop production

USDA-ARS?s Scientific Manuscript database

Fast growing eucalyptus species are selected for commercial plantings worldwide and are harvested for a variety of uses. Eucalyptus plantings in south Florida are harvested for landscape mulch production, yet this material may have potential as a container substrate for horticulture crop production....

Potential of predatory bacteria as biocontrol agents for foodborne and plant pathogens

USDA-ARS?s Scientific Manuscript database

Foodborne pathogens such as Escherichia coli O157:H7, Salmonella spp., Listeria monocytogenes, Shigella are responsible for frequent occurrences of illnesses and mortality in humans and produce losses. Pre-harvest yield losses and post-harvest decay on minimally processed produce (fruits, vegetables...

Ultrasound as an intervention technology for the sanitation of lettuce harvesting knife

USDA-ARS?s Scientific Manuscript database

Lettuce field-coring and trimming practices are recent industry developments designed to improve fresh-cut processing yield and reduce shipping and waste disposal costs. Studies showed that the harvesting/coring knives used could be potentially contaminated with pathogens by contact with contaminat...

IRON-INDUCED CHANGES IN LIGHT HARVESTING AND PHOTOCHEMICAL ENERGY CONVERSION IN EUKARYOTIC MARINE ALGAE

EPA Science Inventory

The role of iron in regulating light harvesting and photochemical energy conversion process was examined in the marine unicellular chlorophyte Dunaliella tertiolecta and the marine diatom Phaeodactylum tricornutum. In both species, iron limitation led to a reduction in cellular c...

Rotating algal biofilm reactor and spool harvester for wastewater treatment with biofuels by-products.

PubMed

Christenson, Logan B; Sims, Ronald C

2012-07-01

Maximizing algae production in a wastewater treatment process can aid in the reduction of soluble nitrogen and phosphorus concentrations in the wastewater. If harvested, the algae-based biomass offers the added benefit as feedstock for the production of biofuels and bioproducts. However, difficulties in harvesting, concentrating, and dewatering the algae-based biomass have limited the development of an economically feasible treatment and production process. When algae-based biomass is grown as a surface attached biofilm as opposed to a suspended culture, the biomass is naturally concentrated and more easily harvested. This can lead to less expensive removal of the biomass from wastewater, and less expensive downstream processing in the production of biofuels and bioproducts. In this study, a novel rotating algal biofilm reactor (RABR) was designed, built, and tested at bench (8 L), medium (535 L), and pilot (8,000 L) scales. The RABR was designed to operate in the photoautotrophic conditions of open tertiary wastewater treatment, producing mixed culture biofilms made up of algae and bacteria. Growth substrata were evaluated for attachment and biofilm formation, and an effective substratum was discovered. The RABR achieved effective nutrient reduction, with average removal rates of 2.1 and 14.1 g m(-2) day(-1) for total dissolved phosphorus and total dissolved nitrogen, respectively. Biomass production ranged from 5.5 g m(-2) day(-1) at bench scale to as high as 31 g m(-2) day(-1) at pilot scale. An efficient spool harvesting technique was also developed at bench and medium scales to obtain a concentrated product (12-16% solids) suitable for further processing in the production of biofuels and bioproducts. Copyright © 2012 Wiley Periodicals, Inc.

MEMS for vibration energy harvesting

NASA Astrophysics Data System (ADS)

Li, Lin; Zhang, Yangjian; San, Haisheng; Guo, Yinbiao; Chen, Xuyuan

2008-03-01

In this paper, a capacitive vibration-to-electrical energy harvester was designed. An integrated process flow for fabricating the designed capacitive harvester is presented. For overcoming the disadvantage of depending on external power source in capacitive energy harvester, two parallel electrodes with different work functions are used as the two electrodes of the capacitor to generate a build-in voltage for initially charging the capacitor. The device is a sandwich structure of silicon layer in two glass layers with area of about 1 cm2. The silicon structure is fabricated by using silicon-on-insulator (SOI) wafer. The glass wafers are anodic bonded on to both sides of the SOI wafer to create a vacuum sealed package.

Using magnetic materials to harvest microalgal biomass: evaluation of harvesting and detachment efficiency.

PubMed

Zhu, L-D; Hiltunen, Erkki; Li, Zhaohua

2017-12-15

Using naked iron oxide (Fe 3 O 4 ) and yttrium iron oxide (Y 3 Fe 5 O 12 ) nanoparticles as flocculants, the harvesting efficiency of Chlorella vulgaris biomass was investigated. The harvesting process includes two steps, which are the separation of microalgae from the culture solution with the magnetic nanoparticles and then the separation of the algae from the magnetic nanoparticles. The optimal dosages and pH values for the magnetic harvesting of microalgal biomass were determined. Results showed that Y 3 Fe 5 O 12 nanoparticles were more efficient in microalgal biomass harvesting than Fe 3 O 4 nanoparticles. In an effort to achieve more than 90% of harvesting efficiency, optimal dosages for Fe 3 O 4 and Y 3 Fe 5 O 12 to harvest microalgal biomass were 10 and 2.5 g/L, while the appropriate pH values were 6.2 and 7.3, respectively. The harvesting efficiency of Fe 3 O 4 and Y 3 Fe 5 O 12 nanoparticles increased as the pH value decreased. The experimental results also showed that under a higher pH value Fe 3 O 4 nanoparticles were much easier to be separated from the flocs than Y 3 Fe 5 O 12 . 62.9% of Fe 3 O 4 nanoparticles could be de-attached from the aggregates, when the floc pH value reached 12.3.

Energy harvesting for human wearable and implantable bio-sensors.

PubMed

Mitcheson, Paul D

2010-01-01

There are clear trade-offs between functionality, battery lifetime and battery volume for wearable and implantable wireless-biosensors which energy harvesting devices may be able to overcome. Reliable energy harvesting has now become a reality for machine condition monitoring and is finding applications in chemical process plants, refineries and water treatment works. However, practical miniature devices that can harvest sufficient energy from the human body to power a wireless bio-sensor are still in their infancy. This paper reviews the options for human energy harvesting in order to determine power availability for harvester-powered body sensor networks. The main competing technologies for energy harvesting from the human body are inertial kinetic energy harvesting devices and thermoelectric devices. These devices are advantageous to some other types as they can be hermetically sealed. In this paper the fundamental limit to the power output of these devices is compared as a function of generator volume when attached to a human whilst walking and running. It is shown that the kinetic energy devices have the highest fundamental power limits in both cases. However, when a comparison is made between the devices using device effectivenesses figures from previously demonstrated prototypes presented in the literature, the thermal device is competitive with the kinetic energy harvesting device when the subject is running and achieves the highest power density when the subject is walking.

Interaction effects between weather and space use on harvesting effort and patterns in red deer.

PubMed

Rivrud, Inger M; Meisingset, Erling L; Loe, Leif E; Mysterud, Atle

2014-12-01

Most cervid populations in Europe and North America are managed through selective harvesting, often with age- and sex-specific quotas, with a large influence on the population growth rate. Less well understood is how prevailing weather affects harvesting selectivity and off-take indirectly through changes in individual animal and hunter behavior. The behavior and movement patterns of hunters and their prey are expected to be influenced by weather conditions. Furthermore, habitat characteristics like habitat openness are also known to affect movement patterns and harvesting vulnerability, but how much such processes affect harvest composition has not been quantified. We use harvest data from red deer (Cervus elaphus) to investigate how weather and habitat characteristics affect behavioral decisions of red deer and their hunters throughout the hunting season. More specifically, we look at how sex and age class, temperature, precipitation, moon phase, and day of week affect the probability of being harvested on farmland (open habitat), hunter effort, and the overall harvest numbers. Moon phase and day of week were the strongest predictors of hunter effort and harvest numbers, with higher effort during full moon and weekends, and higher numbers during full moon. In general, the effect of fall weather conditions and habitat characteristics on harvest effort and numbers varied through the season. Yearlings showed the highest variation in the probability of being harvested on farmland through the season, but there was no effect of sex. Our study is among the first to highlight that weather may affect harvesting patterns and off-take indirectly through animal and hunter behavior, but the interaction effects of weather and space use on hunter behavior are complicated, and seem less important than hunter preference and quotas in determining hunter selection and harvest off-take. The consideration of hunter behavior is therefore key when forming management rules for sustainable harvesting.

Interaction effects between weather and space use on harvesting effort and patterns in red deer

PubMed Central

Rivrud, Inger M; Meisingset, Erling L; Loe, Leif E; Mysterud, Atle

2014-01-01

Most cervid populations in Europe and North America are managed through selective harvesting, often with age- and sex-specific quotas, with a large influence on the population growth rate. Less well understood is how prevailing weather affects harvesting selectivity and off-take indirectly through changes in individual animal and hunter behavior. The behavior and movement patterns of hunters and their prey are expected to be influenced by weather conditions. Furthermore, habitat characteristics like habitat openness are also known to affect movement patterns and harvesting vulnerability, but how much such processes affect harvest composition has not been quantified. We use harvest data from red deer (Cervus elaphus) to investigate how weather and habitat characteristics affect behavioral decisions of red deer and their hunters throughout the hunting season. More specifically, we look at how sex and age class, temperature, precipitation, moon phase, and day of week affect the probability of being harvested on farmland (open habitat), hunter effort, and the overall harvest numbers. Moon phase and day of week were the strongest predictors of hunter effort and harvest numbers, with higher effort during full moon and weekends, and higher numbers during full moon. In general, the effect of fall weather conditions and habitat characteristics on harvest effort and numbers varied through the season. Yearlings showed the highest variation in the probability of being harvested on farmland through the season, but there was no effect of sex. Our study is among the first to highlight that weather may affect harvesting patterns and off-take indirectly through animal and hunter behavior, but the interaction effects of weather and space use on hunter behavior are complicated, and seem less important than hunter preference and quotas in determining hunter selection and harvest off-take. The consideration of hunter behavior is therefore key when forming management rules for sustainable harvesting. PMID:25558369

Comparative mechanical harvest efficiency of New Mexico green chile cultivars

USDA-ARS?s Scientific Manuscript database

New Mexico-type green chile (Capsicum annuum) is one of New Mexico’s leading horticultural commodities. The crop is harvested when fruit are fully sized, but in the physiologically immature green stage, for fresh and processed markets. Cultivated acreage of green chile in New Mexico is threatened du...

INFINITY harvest

NASA Image and Video Library

2012-05-07

Students from Benjamin E. Mays Preparatory School in New Orleans enjoyed a hands-on experience at the INFINITY at NASA Stennis Space Center facility May 7, 2012. The Louisiana students assisted in the first harvest of lettuce from the Controlled Environment Agriculture unit, which uses an aeroponic process that involves no soil and advance LED lighting techniques.

Selection efficiency for raspberry postharvest shelf life affected by storage temperature and harvest season

USDA-ARS?s Scientific Manuscript database

Improved postharvest quality is an important goal for fresh-market raspberry breeding programs. To determine if warm or cold storage following harvest would better facilitate the breeding selection process for the assessment of postharvest decay and bleed, pesticide-free fruit from cultivars and bre...

Carbon sequestration in harvested wood products

Treesearch

K. Skog

2013-01-01

Carbon is continuously cycled among these storage pools and between forest ecosystems and the atmosphere as a result of biological processes in forests (e.g., photosynthesis, respiration, growth, mortality, decomposition, and disturbances such as fires or pest outbreaks) and anthropogenic activities (e.g., harvesting, thinning, clearing, and replanting). As trees...

Veggie Harvest

NASA Image and Video Library

2017-10-27

Charles Spern, project manager on the Engineering Services Contract, communicates instructions for the Veggie system to astronaut Joe Acaba on the International Space Station. Spern is in the Experiment Monitoring Room in the Space Station Processing Facility at Kennedy Space Center in Florida. Three different varieties of plants from the Veg-03D plant experiment were harvested.

Clarification Properties of Trash and Stalk Tissues from Sugarcane

USDA-ARS?s Scientific Manuscript database

The effect of the U.S. and world-wide change from burnt to unburnt (green) sugarcane harvesting on processing, and the use of sugarcane leaves and tops as a biomass source has not been fully characterized. Sugarcane whole-stalks were harvested from the first ratoon crop of five commercial, Louisian...

Simultaneous energy harvesting and information processing in wireless multiple relays with multiple antennas

NASA Astrophysics Data System (ADS)

Albaaj, Azhar; Makki, S. Vahab A.; Alabkhat, Qassem; Zahedi, Abdulhamid

2017-07-01

Wireless networks suffer from battery discharging specially in cooperative communications when multiple relays have an important role but they are energy constrained. To overcome this problem, energy harvesting from radio frequency signals is applied to charge the node battery. These intermediate nodes have the ability to harvest energy from the source signal and use the energy harvested to transmit information to the destination. In fact, the node tries to harvest energy and then transmit the data to destination. Division of energy harvesting and data transmission can be done in two algorithms: time-switching-based relaying protocol and power-splitting-based relaying protocol. These two algorithms also can be applied in delay-limited and delay-tolerant transmission systems. The previous works have assumed a single relay for energy harvesting, but in this article, the proposed method is concentrated on improving the outage probability and throughput by using multiple antennas in each relay node instead of using single antenna. According to our simulation results, when using multi-antenna relays, ability of energy harvesting is increased and thus system performance will be improved to great extent. Maximum ratio combining scheme has been used when the destination chooses the best signal of relays and antennas satisfying the required signal-to-noise ratio.

Structure Optimization of a Grain Impact Piezoelectric Sensor and Its Application for Monitoring Separation Losses on Tangential-Axial Combine Harvesters

PubMed Central

Liang, Zhenwei; Li, Yaoming; Zhao, Zhan; Xu, Lizhang

2015-01-01

Grain separation losses is a key parameter to weigh the performance of combine harvesters, and also a dominant factor for automatically adjusting their major working parameters. The traditional separation losses monitoring method mainly rely on manual efforts, which require a high labor intensity. With recent advancements in sensor technology, electronics and computational processing power, this paper presents an indirect method for monitoring grain separation losses in tangential-axial combine harvesters in real-time. Firstly, we developed a mathematical monitoring model based on detailed comparative data analysis of different feeding quantities. Then, we developed a grain impact piezoelectric sensor utilizing a YT-5 piezoelectric ceramic as the sensing element, and a signal process circuit designed according to differences in voltage amplitude and rise time of collision signals. To improve the sensor performance, theoretical analysis was performed from a structural vibration point of view, and the optimal sensor structural has been selected. Grain collide experiments have shown that the sensor performance was greatly improved. Finally, we installed the sensor on a tangential-longitudinal axial combine harvester, and grain separation losses monitoring experiments were carried out in North China, which results have shown that the monitoring method was feasible, and the biggest measurement relative error was 4.63% when harvesting rice. PMID:25594592

Flexible thermoelectric device to harvest waste heat from the laptop

NASA Astrophysics Data System (ADS)

Salhi, Imane; Belhora, Fouad; Hajjaji, Abdelowahed; Jay, Jacques; Boughaleb, Yahia

2017-05-01

Recovering waste heat from integrated circuits of a laptop using thermoelectricity effects seems to be an appropriate process to enhance its efficiency. Thermoelectricity, as an energy harvesting process, helps to gain on both sides: financially as it reduces the energy consumption and environmentally as it minimizes the carbon footprint. This paper presents a flexible thermoelectric generator module which is developed to harvest waste heat of the laptop to power up some external loads. First, a theoretical analysis of the system is provided where both thermal and electrical models are exposed. Second, an estimation of the power density harvested by only one thermoelectric leg is given. This estimation can reach 0.01 µW/cm2 and it is confirmed by a numerical simulation based on the finite element method. Afterwards, this power density is improved to become 0.4 µW/cm2 by adding a heat sink in the cold side showing that the thermal resistances of the air and of the heat sink play a crucial role in transferring the temperature gradient to the thermoelectric (TE) material. Finally, it is indicated that the power harvested can be enough to power up portion of the circuitry or other important micro-accessories by using numerous thermoelectric modules.

Structure optimization of a grain impact piezoelectric sensor and its application for monitoring separation losses on tangential-axial combine harvesters.

PubMed

Liang, Zhenwei; Li, Yaoming; Zhao, Zhan; Xu, Lizhang

2015-01-14

Grain separation losses is a key parameter to weigh the performance of combine harvesters, and also a dominant factor for automatically adjusting their major working parameters. The traditional separation losses monitoring method mainly rely on manual efforts, which require a high labor intensity. With recent advancements in sensor technology, electronics and computational processing power, this paper presents an indirect method for monitoring grain separation losses in tangential-axial combine harvesters in real-time. Firstly, we developed a mathematical monitoring model based on detailed comparative data analysis of different feeding quantities. Then, we developed a grain impact piezoelectric sensor utilizing a YT-5 piezoelectric ceramic as the sensing element, and a signal process circuit designed according to differences in voltage amplitude and rise time of collision signals. To improve the sensor performance, theoretical analysis was performed from a structural vibration point of view, and the optimal sensor structural has been selected. Grain collide experiments have shown that the sensor performance was greatly improved. Finally, we installed the sensor on a tangential-longitudinal axial combine harvester, and grain separation losses monitoring experiments were carried out in North China, which results have shown that the monitoring method was feasible, and the biggest measurement relative error was 4.63% when harvesting rice.

Electrokinetic Supercapacitor for Simultaneous Harvesting and Storage of Mechanical Energy.

PubMed

Yang, Peihua; Qu, Xiaopeng; Liu, Kang; Duan, Jiangjiang; Li, Jia; Chen, Qian; Xue, Guobin; Xie, Wenke; Xu, Zhimou; Zhou, Jun

2018-03-07

Energy harvesting and storage are two distinct processes that are generally achieved using two separated parts based on different physical and chemical principles. Here we report a self-charging electrokinetic supercapacitor that directly couples the energy harvesting and storage processes into one device. The device consists of two identical carbon nanotube/titanium electrodes, separated by a piece of anodic aluminum oxide nanochannels membrane. Pressure-driven electrolyte flow through the nanochannels generates streaming potential, which can be used to charge the capacitive electrodes, accomplishing simultaneous energy generation and storage. The device stores electric charge density of 0.4 mC cm -2 after fully charging under pressure of 2.5 bar. This work may offer a train of thought for the development of a new type of energy unit for self-powered systems.

The effect of assisted reproduction treatment on mental health in fertile women.

PubMed

Zivaridelavar, Maryam; Kazemi, Ashraf; Kheirabadi, Gholam Reza

2016-01-01

The process of assisted reproductive treatment is a stressful situation in the treatment of infertile couples and it would harm the mental health of women. Fertile women who started infertility treatment due to male factor infertility have reported to experience less stress and depression than other women before the assisted reproductive process but considering the cultural and social factors and also the etiology of the assisted reproductive process, it could affect the metal health of these women. Therefore, this study was conducted to evaluate the mental health of fertile women who undergo assisted reproductive treatment due to male factor infertility. This study was a prospective study on 70 fertile women who underwent assisted reproductive treatment due to male factor infertility. The exclusion criterion was to stop super ovulation induction. To assess mental health, anxiety and depression dimensions of the general health questionnaire were used. Before starting ovulation induction and after oocyte harvesting, the general health questionnaire was filled by women who were under treatment. Data were analyzed using multi-variable linear regression, paired t-test, and Chi-square. The results showed that the mean score of depression and anxiety before ovulation induction and after oocyte harvesting were not significantly different; but the rate of mental health disorder in the depression dimension was significantly decreased after oocytes harvesting (31.7% vs. 39.7%). Also, there was a significant relation between the level of anxiety and depression before ovulation induction and after oocyte harvesting (P < 0.05). The anxiety level after oocyte harvesting had a positive and significant correlation with the economic situation (P < 0.05). This study revealed that the process of assisted reproductive treatment does not affect the mental health in fertile women independently, but these women start assisted reproductive process with high levels of depression and anxiety. Therefore, prior to the assisted reproductive treatment mental health consultation is needed.

Piezoelectric energy harvesting computer controlled test bench

NASA Astrophysics Data System (ADS)

Vázquez-Rodriguez, M.; Jiménez, F. J.; de Frutos, J.; Alonso, D.

2016-09-01

In this paper a new computer controlled (C.C.) laboratory test bench is presented. The patented test bench is made up of a C.C. road traffic simulator, C.C. electronic hardware involved in automating measurements, and test bench control software interface programmed in LabVIEW™. Our research is focused on characterizing electronic energy harvesting piezoelectric-based elements in road traffic environments to extract (or "harvest") maximum power. In mechanical to electrical energy conversion, mechanical impacts or vibrational behavior are commonly used, and several major problems need to be solved to perform optimal harvesting systems including, but no limited to, primary energy source modeling, energy conversion, and energy storage. It is described a novel C.C. test bench that obtains, in an accurate and automatized process, a generalized linear equivalent electrical model of piezoelectric elements and piezoelectric based energy store harvesting circuits in order to scale energy generation with multiple devices integrated in different topologies.

Piezoelectric energy harvesting computer controlled test bench.

PubMed

Vázquez-Rodriguez, M; Jiménez, F J; de Frutos, J; Alonso, D

2016-09-01

In this paper a new computer controlled (C.C.) laboratory test bench is presented. The patented test bench is made up of a C.C. road traffic simulator, C.C. electronic hardware involved in automating measurements, and test bench control software interface programmed in LabVIEW™. Our research is focused on characterizing electronic energy harvesting piezoelectric-based elements in road traffic environments to extract (or "harvest") maximum power. In mechanical to electrical energy conversion, mechanical impacts or vibrational behavior are commonly used, and several major problems need to be solved to perform optimal harvesting systems including, but no limited to, primary energy source modeling, energy conversion, and energy storage. It is described a novel C.C. test bench that obtains, in an accurate and automatized process, a generalized linear equivalent electrical model of piezoelectric elements and piezoelectric based energy store harvesting circuits in order to scale energy generation with multiple devices integrated in different topologies.

Understanding how surface chemistry and topography enhance fog harvesting based on the superwetting surface with patterned hemispherical bulges.

PubMed

Zhong, Lieshuang; Zhu, Hai; Wu, Yang; Guo, Zhiguang

2018-09-01

The Namib Desert beetle-Stenocara can adapt to the arid environment by its fog harvesting ability. A series of samples with different topography and wettability that mimicked the elytra of the beetle were fabricated to study the effect of these factors on fog harvesting. The superhydrophobic bulgy sample harvested 1.5 times the amount of water than the sample with combinational pattern of hydrophilic bulgy/superhydrophobic surrounding and 2.83 times than the superhydrophobic surface without bulge. These bulges focused the droplets around them which endowed droplets with higher velocity and induced the highest dynamic pressure atop them. Superhydrophobicity was beneficial for the departure of harvested water on the surface of sample. The bulgy topography, together with surface wettability, dominated the process of water supply and water removal. Copyright © 2018 Elsevier Inc. All rights reserved.

From lab to full-scale ultrafiltration in microalgae harvesting

NASA Astrophysics Data System (ADS)

Wenten, I. G.; Steven, S.; Dwiputra, A.; Khoiruddin; Hakim, A. N.

2017-07-01

Ponding system is generally used for microalgae cultivation. However, selection of appropriate technology for the harvesting process is challenging due to the low cell density of cultivated microalgae from the ponding system and the large volume of water to be handled. One of the promising technologies for microalgae harvesting is ultrafiltration (UF). In this study, the performance of UF during harvesting of microalgae in a lab- and a full-scale test is investigated. The performances of both scales are compared and analyzed to provide an understanding of several aspects which affect the yield produced from lab and actual conditions. Furthermore, a unique self-standing non-modular UF is introduced in the full-scale test. The non-modular UF exhibits several advantages, such as simple piping and connection, single pump for filtration and backwashing, and smaller footprint. With those advantages, the non-modular UF could be a promising technology for microalgae harvesting in industrial-scale.

Scaling prospects in mechanical energy harvesting with piezo nanowires

NASA Astrophysics Data System (ADS)

Ardila, Gustavo; Hinchet, Ronan; Mouis, Mireille; Montès, Laurent

2013-07-01

The combination of 3D processing technologies, low power circuits and new materials integration makes it conceivable to build autonomous integrated systems, which would harvest their energy from the environment. In this paper, we focus on mechanical energy harvesting and discuss its scaling prospects toward the use of piezoelectric nanostructures, able to be integrated in a CMOS environment. It is shown that direct scaling of present MEMS-based methodologies would be beneficial for high-frequency applications only. For the range of applications which is presently foreseen, a different approach is needed, based on energy harvesting from direct real-time deformation instead of energy harvesting from vibration modes at or close to resonance. We discuss the prospects of such an approach based on simple scaling rules Contribution to the Topical Issue “International Semiconductor Conference Dresden-Grenoble - ISCDG 2012”, Edited by Gérard Ghibaudo, Francis Balestra and Simon Deleonibus.

Local sensitivity of per-recruit fishing mortality reference points.

PubMed

Cadigan, N G; Wang, S

2016-12-01

We study the sensitivity of fishery management per-recruit harvest rates which may be part of a quantitative harvest strategy designed to achieve some objective for catch or population size. We use a local influence sensitivity analysis to derive equations that describe how these reference harvest rates are affected by perturbations to productivity processes. These equations give a basic theoretical understanding of sensitivity that can be used to predict what the likely impacts of future changes in productivity will be. Our results indicate that per-recruit reference harvest rates are more sensitive to perturbations when the equilibrium catch or population size per recruit, as functions of the harvest rate, have less curvature near the reference point. Overall our results suggest that per recruit reference points will, with some exceptions, usually increase if (1) growth rates increase, (2) natural mortality rates increase, or (3) fishery selectivity increases to an older age.

Impulsive control of a continuous-culture and flocculation harvest chemostat model

NASA Astrophysics Data System (ADS)

Zhang, Tongqian; Ma, Wanbiao; Meng, Xinzhu

2017-12-01

In this paper, a new mathematical model describing the process of continuous culture and harvest of microalgaes is proposed. By inputting medium and flocculant at two different fixed moments periodically, continuous culture and harvest of microalgaes is implemented. The mathematical analysis is conducted and the whole dynamics of model is investigated by using theory of impulsive differential equations. We find that the model has a microalgaes-extinction periodic solution and it is globally asymptotically stable when some certain threshold value is less than the unit. And the model is permanent when some certain threshold value is larger than the unit. Then, according to the threshold, the control strategies of continuous culture and harvest of microalgaes are discussed. The results show that continuous culture and harvest of microalgaes can be archived by adjusting suitable input time, input amount of medium or flocculant. Finally, some numerical simulations are carried out to verify the control strategy.

Single crystals and nonlinear process for outstanding vibration-powered electrical generators.

PubMed

Badel, Adrien; Benayad, Abdelmjid; Lefeuvre, Elie; Lebrun, Laurent; Richard, Claude; Guyomar, Daniel

2006-04-01

This paper compares the performances of vibration-powered electrical generators using a piezoelectric ceramic and a piezoelectric single crystal associated to several power conditioning circuits. A new approach of the piezoelectric power conversion based on a nonlinear voltage processing is presented, leading to three novel high performance power conditioning interfaces. Theoretical predictions and experimental results show that the nonlinear processing technique may increase the power harvested by a factor of 8 compared to standard techniques. Moreover, it is shown that, for a given energy harvesting technique, generators using single crystals deliver 20 times more power than generators using piezoelectric ceramics.

Changes in Volatile and Non-Volatile Flavor Chemicals of “Valencia” Orange Juice over the Harvest Seasons

PubMed Central

Bai, Jinhe; Baldwin, Elizabeth A.; McCollum, Greg; Plotto, Anne; Manthey, John A.; Widmer, Wilbur W.; Luzio, Gary; Cameron, Randall

2016-01-01

Florida “Valencia” oranges have a wide harvest window, covering four months after first reaching the commercial maturity. However, the influence of harvest time on juice flavor chemicals is not well documented, with the exception of sugars and acids. Therefore, we investigated the major flavor chemicals, volatile (aroma), non-volatile (taste) and mouth feel attributes, in the two harvest seasons (March to June in 2007 and February to May in 2012). Bitter limonoid compounds, limonin and nomilin, decreased gradually. Out of a total of 94 volatiles, 32 increased, 47 peaked mid to late season, and 15 decreased. Juice insoluble solids and pectin content increased over the season; however, pectin methylesterase activity remained unchanged. Fruit harvested in the earlier months had lower flavor quality. Juice from later harvests had a higher sugar/acid ratio with less bitterness, while, many important aroma compounds occurred at the highest concentrations in the middle to late season, but occurred at lower concentrations at the end of the season. The results provide information to the orange juice processing industry for selection of optimal harvest time and for setting of precise blending strategy. PMID:28231099

Changes in Volatile and Non-Volatile Flavor Chemicals of "Valencia" Orange Juice over the Harvest Seasons.

PubMed

Bai, Jinhe; Baldwin, Elizabeth A; McCollum, Greg; Plotto, Anne; Manthey, John A; Widmer, Wilbur W; Luzio, Gary; Cameron, Randall

2016-01-04

Florida "Valencia" oranges have a wide harvest window, covering four months after first reaching the commercial maturity. However, the influence of harvest time on juice flavor chemicals is not well documented, with the exception of sugars and acids. Therefore, we investigated the major flavor chemicals, volatile (aroma), non-volatile (taste) and mouth feel attributes, in the two harvest seasons (March to June in 2007 and February to May in 2012). Bitter limonoid compounds, limonin and nomilin, decreased gradually. Out of a total of 94 volatiles, 32 increased, 47 peaked mid to late season, and 15 decreased. Juice insoluble solids and pectin content increased over the season; however, pectin methylesterase activity remained unchanged. Fruit harvested in the earlier months had lower flavor quality. Juice from later harvests had a higher sugar/acid ratio with less bitterness, while, many important aroma compounds occurred at the highest concentrations in the middle to late season, but occurred at lower concentrations at the end of the season. The results provide information to the orange juice processing industry for selection of optimal harvest time and for setting of precise blending strategy.

A novel method for energy harvesting simulation based on scenario generation

NASA Astrophysics Data System (ADS)

Wang, Zhe; Li, Taoshen; Xiao, Nan; Ye, Jin; Wu, Min

2018-06-01

Energy harvesting network (EHN) is a new form of computer networks. It converts ambient energy into usable electric energy and supply the electrical energy as a primary or secondary power source to the communication devices. However, most of the EHN uses the analytical probability distribution function to describe the energy harvesting process, which cannot accurately identify the actual situation for the lack of authenticity. We propose an EHN simulation method based on scenario generation in this paper. Firstly, instead of setting a probability distribution in advance, it uses optimal scenario reduction technology to generate representative scenarios in single period based on the historical data of the harvested energy. Secondly, it uses homogeneous simulated annealing algorithm to generate optimal daily energy harvesting scenario sequences to get a more accurate simulation of the random characteristics of the energy harvesting network. Then taking the actual wind power data as an example, the accuracy and stability of the method are verified by comparing with the real data. Finally, we cite an instance to optimize the network throughput, which indicate the feasibility and effectiveness of the method we proposed from the optimal solution and data analysis in energy harvesting simulation.

Thermal energy harvesters with piezoelectric or electrostatic transducer

NASA Astrophysics Data System (ADS)

Prokaryn, Piotr; Domański, Krzysztof; Marchewka, Michał; Tomaszewski, Daniel; Grabiec, Piotr; Puscasu, Onoriu; Monfray, Stéphane; Skotnicki, Thomas

2014-08-01

This paper describes the idea of the energy harvester which converts thermal gradient present in environment into electricity. Two kinds of such devices are proposed and their prototypes are shown and discussed. The main parts of harvesters are bimetallic spring, piezoelectric transducer or electrostatic transducer with electret. The applied piezomembrane was commercial available product but electrets was made by authors. In the paper a fabrication procedure of electrets formed by the corona discharge process is described. Devices were compared in terms of generated power, charging current, and the voltage across a storage capacitor.

A 6.45 μW Self-Powered SoC With Integrated Energy-Harvesting Power Management and ULP Asymmetric Radios for Portable Biomedical Systems.

PubMed

Roy, Abhishek; Klinefelter, Alicia; Yahya, Farah B; Chen, Xing; Gonzalez-Guerrero, Luisa Patricia; Lukas, Christopher J; Kamakshi, Divya Akella; Boley, James; Craig, Kyle; Faisal, Muhammad; Oh, Seunghyun; Roberts, Nathan E; Shakhsheer, Yousef; Shrivastava, Aatmesh; Vasudevan, Dilip P; Wentzloff, David D; Calhoun, Benton H

2015-12-01

This paper presents a batteryless system-on-chip (SoC) that operates off energy harvested from indoor solar cells and/or thermoelectric generators (TEGs) on the body. Fabricated in a commercial 0.13 μW process, this SoC sensing platform consists of an integrated energy harvesting and power management unit (EH-PMU) with maximum power point tracking, multiple sensing modalities, programmable core and a low power microcontroller with several hardware accelerators to enable energy-efficient digital signal processing, ultra-low-power (ULP) asymmetric radios for wireless transmission, and a 100 nW wake-up radio. The EH-PMU achieves a peak end-to-end efficiency of 75% delivering power to a 100 μA load. In an example motion detection application, the SoC reads data from an accelerometer through SPI, processes it, and sends it over the radio. The SPI and digital processing consume only 2.27 μW, while the integrated radio consumes 4.18 μW when transmitting at 187.5 kbps for a total of 6.45 μW.

Algal Lipids and Omega-3 Production via Autotrophic and Heterotrophic Pathways at Cellana?s Kona Demonstration Facility, Hawaii

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bai, Xuemei; Knurek, Emily; Goes, Nikki

2012-05-05

Cellana?s Kona Demonstration Facility (KDF) is a 2.5 hectare facility, with 17,000 sq. ft. under roof and 1 hectare of cultivation systems. KDF is designed to execute and support all stages of the production process at pilot scale, from cultivation through extraction. Since Feb. 2009, KDF has been producing up to 0.7MT dry weight of algal biomass per month, while at the same time optimizing processes of cultivation, harvesting, dewatering and extraction. The cultivation system at KDF uses ALDUO? technology, a hybrid system of photobioreactors (PBRs) and open ponds. All fluid transfers related to KDF cultivation and harvesting processes aremore » operated and monitored by a remote Process-Control System. Fluid transfer data, together with biochemical data, enable the mass balance calculations necessary to measure productivity. This poster summarizes methods to improve both biomass and lipids yield by 1) alleviating light limitation in open ponds, 2) de-oxygenation and 3) heterotrophic lipid production for post-harvesting cultures.« less

78 FR 36122 - Fisheries of the Exclusive Economic Zone Off Alaska; Bering Sea and Aleutian Islands Crab...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-17

... the harvesting and processing sectors'' and to monitor the ``economic stability for harvesters.... 120806311-3530-02] RIN 0648-BC25 Fisheries of the Exclusive Economic Zone Off Alaska; Bering Sea and... Tanner Crabs (FMP). These regulations revise the annual economic data reports (EDRs) currently required...

INFINITY harvest

NASA Image and Video Library

2012-05-07

The Controlled Environment Agriculture unit at the INFINITY at NASA Stennis Space Center visitor center and museum grows butterhead lettuce using an aeroponic process that involves no soil and advance LED lighting techniques. Students from Benjamin E. Mays Preparatory School in New Orleans helped to harvest the first crop of lettuce during a visit to the facility May 7, 2012.

Wood bioenergy and soil productivity research

Treesearch

D. Andrew Scott; Deborah S. Page-Dumroese

2016-01-01

Timber harvesting can cause both short- and long-term changes in forest ecosystem functions, and scientists from USDA Forest Service (USDA FS) have been studying these processes for many years. Biomass and bioenergy markets alter the amount, type, and frequency at which material is harvested, which in turn has similar yet specific impacts on sustainable productivity....

Wyoming's forest products industry and timber harvest, 2005

Treesearch

Jason P. Brandt; Todd A. Morgan; Mike T. Thompson

2009-01-01

This report traces the flow of Wyoming's 2005 timber harvest through the primary timber-processing industry to the wholesale market and residue-using sectors. The structure, capacity, operations, and conditions of Wyoming's primary forest products industry are described; and volumes and uses of wood fiber are quantified. Historical and recent changes in...

Mississippi forest industry

Treesearch

Dwane D. Van Hooser

1968-01-01

Nearly 402 million cubic feet of industrial roundwood were harvested in Mississippi in 1966. This was the largest harvest in a decade. Nearly three-fifths was softwood-mainly pine. Altogether, 305 million cubic feet were processed by the State's forest industries. Some 123 million cubic feet were shipped to surrounding States, while 26 million cubic feet were...

The physiological basis for regeneration response to variable retention harvest treatments in three pine species

Treesearch

Matthew D. Powers; Kurt S. Pregitzer; Brian J. Palik; Christopher R. Webster

2011-01-01

Variable retention harvesting (VRH) is promoted for enhancing biodiversity and ecosystem processes in managed forests, but regeneration responses to the complex stand structures that result from VRH are poorly understood. We analyzed foliar stable carbon isotope ratios (δ13C), oxygen isotope ratios (δ18O...

Woody biomass logistics [Chapter 14

Treesearch

Robert Keefe; Nathaniel Anderson; John Hogland; Ken Muhlenfeld

2014-01-01

The economics of using woody biomass as a fuel or feedstock for bioenergy applications is often driven by logistical considerations. Depending on the source of the woody biomass, the acquisition cost of the material is often quite low, sometimes near zero. However, the cost of harvesting, collection, processing, storage, and transportation from the harvest site to end...

Optimal control of raw timber production processes

Treesearch

Ivan Kolenka

1978-01-01

This paper demonstrates the possibility of optimal planning and control of timber harvesting activ-ities with mathematical optimization models. The separate phases of timber harvesting are represented by coordinated models which can be used to select the optimal decision for the execution of any given phase. The models form a system whose components are connected and...

The Effect of Green Sugarcane on Downstream Processing at Two Midlands Factories

USDA-ARS?s Scientific Manuscript database

There is a worldwide shift to green cane from burnt cane harvesting. In many countries including the U.S. and South Africa, certain areas are changing to green cane harvesting due to public and environmental pressures against open field burning, increasing labor costs, and the current trend to inve...

Wave Energy Prize - 1/50th Testing - Team Flapper/Harvest

DOE Data Explorer

Wesley Scharmen

2015-12-18

This submission of data includes all the 1/50th scale testing data completed on the Wave Energy Prize for the Team Flapper/Harvest, and includes: 1/50th test data (raw & processed) 1/50th test data video and pictures 1/50th Test plans and testing documents SSTF_Submission (summarized results)

Development and characterization of 13 polymorphic microsatellite loci for Cryptolepsis sanguinolenta, an African antimalarial plant

USDA-ARS?s Scientific Manuscript database

Cryptolepsis sanguinolenta is an herbaceous perennial plant indigenous to West and Central Africa. The roots are harvested and widely used in the preparation of herbal decoctions to treat malaria. The process of harvesting wild grown roots is unsustainable, and the plant is becoming more difficult t...

Quantum coherence spectroscopy reveals complex dynamics in bacterial light-harvesting complex 2 (LH2).

PubMed

Harel, Elad; Engel, Gregory S

2012-01-17

Light-harvesting antenna complexes transfer energy from sunlight to photosynthetic reaction centers where charge separation drives cellular metabolism. The process through which pigments transfer excitation energy involves a complex choreography of coherent and incoherent processes mediated by the surrounding protein and solvent environment. The recent discovery of coherent dynamics in photosynthetic light-harvesting antennae has motivated many theoretical models exploring effects of interference in energy transfer phenomena. In this work, we provide experimental evidence of long-lived quantum coherence between the spectrally separated B800 and B850 rings of the light-harvesting complex 2 (LH2) of purple bacteria. Spectrally resolved maps of the detuning, dephasing, and the amplitude of electronic coupling between excitons reveal that different relaxation pathways act in concert for optimal transfer efficiency. Furthermore, maps of the phase of the signal suggest that quantum mechanical interference between different energy transfer pathways may be important even at ambient temperature. Such interference at a product state has already been shown to enhance the quantum efficiency of transfer in theoretical models of closed loop systems such as LH2.

Quantum coherence spectroscopy reveals complex dynamics in bacterial light-harvesting complex 2 (LH2)

PubMed Central

Harel, Elad; Engel, Gregory S.

2012-01-01

Light-harvesting antenna complexes transfer energy from sunlight to photosynthetic reaction centers where charge separation drives cellular metabolism. The process through which pigments transfer excitation energy involves a complex choreography of coherent and incoherent processes mediated by the surrounding protein and solvent environment. The recent discovery of coherent dynamics in photosynthetic light-harvesting antennae has motivated many theoretical models exploring effects of interference in energy transfer phenomena. In this work, we provide experimental evidence of long-lived quantum coherence between the spectrally separated B800 and B850 rings of the light-harvesting complex 2 (LH2) of purple bacteria. Spectrally resolved maps of the detuning, dephasing, and the amplitude of electronic coupling between excitons reveal that different relaxation pathways act in concert for optimal transfer efficiency. Furthermore, maps of the phase of the signal suggest that quantum mechanical interference between different energy transfer pathways may be important even at ambient temperature. Such interference at a product state has already been shown to enhance the quantum efficiency of transfer in theoretical models of closed loop systems such as LH2. PMID:22215585

Single-step colloidal quantum dot films for infrared solar harvesting

NASA Astrophysics Data System (ADS)

Kiani, Amirreza; Sutherland, Brandon R.; Kim, Younghoon; Ouellette, Olivier; Levina, Larissa; Walters, Grant; Dinh, Cao-Thang; Liu, Mengxia; Voznyy, Oleksandr; Lan, Xinzheng; Labelle, Andre J.; Ip, Alexander H.; Proppe, Andrew; Ahmed, Ghada H.; Mohammed, Omar F.; Hoogland, Sjoerd; Sargent, Edward H.

2016-10-01

Semiconductors with bandgaps in the near- to mid-infrared can harvest solar light that is otherwise wasted by conventional single-junction solar cell architectures. In particular, colloidal quantum dots (CQDs) are promising materials since they are cost-effective, processed from solution, and have a bandgap that can be tuned into the infrared (IR) via the quantum size effect. These characteristics enable them to harvest the infrared portion of the solar spectrum to which silicon is transparent. To date, IR CQD solar cells have been made using a wasteful and complex sequential layer-by-layer process. Here, we demonstrate ˜1 eV bandgap solar-harvesting CQD films deposited in a single step. By engineering a fast-drying solvent mixture for metal iodide-capped CQDs, we deposited active layers greater than 200 nm in thickness having a mean roughness less than 1 nm. We integrated these films into infrared solar cells that are stable in air and exhibit power conversion efficiencies of 3.5% under illumination by the full solar spectrum, and 0.4% through a simulated silicon solar cell filter.

Pesticide uptake in potatoes: model and field experiments.

PubMed

Juraske, Ronnie; Vivas, Carmen S Mosquera; Velásquez, Alexander Erazo; Santos, Glenda García; Moreno, Mónica B Berdugo; Gomez, Jaime Diaz; Binder, Claudia R; Hellweg, Stefanie; Dallos, Jairo A Guerrero

2011-01-15

A dynamic model for uptake of pesticides in potatoes is presented and evaluated with measurements performed within a field trial in the region of Boyacá, Colombia. The model takes into account the time between pesticide applications and harvest, the time between harvest and consumption, the amount of spray deposition on soil surface, mobility and degradation of pesticide in soil, diffusive uptake and persistence due to crop growth and metabolism in plant material, and loss due to food processing. Food processing steps included were cleaning, washing, storing, and cooking. Pesticide concentrations were measured periodically in soil and potato samples from the beginning of tuber formation until harvest. The model was able to predict the magnitude and temporal profile of the experimentally derived pesticide concentrations well, with all measurements falling within the 90% confidence interval. The fraction of chlorpyrifos applied on the field during plant cultivation that eventually is ingested by the consumer is on average 10(-4)-10(-7), depending on the time between pesticide application and ingestion and the processing step considered.

[Comparison of different harvest ways of Dendrobium officinale].

PubMed

Wang, Yang; Zhu, Yan; Si, Jin-Ping; Liu, Jing-Jing; Zhu, Yu-Qiu; Liu, Xiu-Juan

2015-03-01

To standardize the harvest ways of Dendrobium officinale and improve the quality and yield of D. officinale, a field experiment was carried out to study the effect of two kinds of harvest ways, which were keeping some of the axial shoot and harvesting all of the shoot by the end of the year. Then, the agronomic traits and yield were measured and the contents of polysaccharides and extractum were determined. The results showed that the harvest ways significantly affected the growth of D. officinale. Keeping some of the axial shoot could significantly improved the number of sprout, stem length, internode number and the internodal length, which also triggered increase the weight of fresh stems, leaves and the total of them and dry stems in per unit area, but it could not promote the stem diameter and the polysaccharide content in stems. Keeping some of the axial shoot moderately was conducive to the improvement of the production of medicinal materials in the process of harvesting by promoting the germination and growth of new buds, and to ensure the polysaccharide content by regulating the illumination and the density of cultivation.

Food Safety Impacts from Post-Harvest Processing Procedures of Molluscan Shellfish.

PubMed

Baker, George L

2016-04-18

Post-harvest Processing (PHP) methods are viable food processing methods employed to reduce human pathogens in molluscan shellfish that would normally be consumed raw, such as raw oysters on the half-shell. Efficacy of human pathogen reduction associated with PHP varies with respect to time, temperature, salinity, pressure, and process exposure. Regulatory requirements and PHP molluscan shellfish quality implications are major considerations for PHP usage. Food safety impacts associated with PHP of molluscan shellfish vary in their efficacy and may have synergistic outcomes when combined. Further research for many PHP methods are necessary and emerging PHP methods that result in minimal quality loss and effective human pathogen reduction should be explored.

Emissions of PAHs derived from sugarcane burning and processing in Chiapas and Morelos México.

PubMed

Mugica-Alvarez, Violeta; Santiago-de la Rosa, Naxieli; Figueroa-Lara, Jesús; Flores-Rodríguez, Julio; Torres-Rodríguez, Miguel; Magaña-Reyes, Miguel

2015-09-15

Sugarcane burning is an agricultural practice implemented to ease farm worker duties; nevertheless, as a consequence, tons of particles are emitted to the atmosphere. Additionally, during harvesting the sugar-mills operate the whole day emitting hundreds of tons of pollutants. Therefore, health risks to neighboring population should be a major governmental concern, leading first to identification and quantification of toxic compounds, such as polycyclic aromatic hydrocarbons (PAHs). In order to establish the magnitude of the problem, four sampling campaigns of PM10 and PM2.5 were carried out in this study, during harvesting and no-harvesting seasons in two municipalities of México, with different climatic and social conditions. Concentrations of PM10, PM2.5, and organic compounds were determined daily, followed by extraction, identification and quantification of the 17 EPA-established PAHs from all samples. The results showed that during harvest, the PM10 mass increased lightly in Chiapas, but approximately twice in Morelos, whereas total PAH concentrations increased twice and six times, respectively. The most abundant PAHs, namely: indene [1,2,3cd] pyrene, benzo[b]fluoranthene, benzo[a]pyrene and dibenzo [a,h] anthracene are composed of 5 or more aromatic rings. Of the total PAHs quantified, 44% to 52% corresponded to carcinogenic compounds, consequently, the overall carcinogenic potential increased twice or three times. Principal component analysis with varimax rotation was applied to source apportionment at each site, suggesting three different sources during harvesting: the combustion process in the sugar mill, sugarcane burning and vehicular emissions. The combustion markers for sugar mill are, BAA, BBF, BKF, BAP, IND and BGP, whereas for sugarcane burning were ANT, PHE, FLT and PYR. The results obtained indicate that processing and burning sugarcane are the main sources of the PAH levels measured, proving that the health risks are boosted during harvesting due to increases of PM and PAHs. Copyright © 2015 Elsevier B.V. All rights reserved.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hess, J. Richard; Lamers, Patrick; Roni, Mohammad S.

Logistical barrier are tied to feedstock harvesting, collection, storage and distribution. Current crop harvesting machinery is unable to selectively harvest preferred components of cellulosic biomass while maintaining acceptable levels of soil carbon and minimizing erosion. Actively managing biomass variability imposes additional functional requirements on biomass harvesting equipment. A physiological variation in biomass arises from differences in genetics, degree of crop maturity, geographical location, climatic events, and harvest methods. This variability presents significant cost and performance risks for bioenergy systems. Currently, processing standards and specifications for cellulosic feedstocks are not as well-developed as for mature commodities. Biomass that is stored withmore » high moisture content or exposed to moisture during storage is susceptible to spoilage, rotting, spontaneous combustion, and odor problems. Appropriate storage methods and strategies are needed to better define storage requirements to preserve the volume and quality of harvested biomass over time and maintain its conversion yield. Raw herbaceous biomass is costly to collect, handle, and transport because of its low density and fibrous nature. Existing conventional, bale-based handling equipment and facilities cannot cost-effectively deliver and store high volumes of biomass, even with improved handling techniques. Current handling and transportation systems designed for moving woodchips can be inefficient for bioenergy processes due to the costs and challenges of transporting, storing, and drying high-moisture biomass. The infrastructure for feedstock logistics has not been defined for the potential variety of locations, climates, feedstocks, storage methods, processing alternatives, etc., which will occur at a national scale. When setting up biomass fuel supply chains, for large-scale biomass systems, logistics are a pivotal part in the system. Various studies have shown that long-distance international transport by ship is feasible in terms of energy use and transportation costs, but availability of suitable vessels and meteorological conditions (e.g., winter time in Scandinavia and Russia) need to be considered. However, local transportation by truck (both in biomass exporting and importing countries) may be a high-cost factor, which can influence the overall energy balance and total biomass costs.« less

Multilevel learning in the adaptive management of waterfowl harvests: 20 years and counting

USGS Publications Warehouse

Johnson, Fred A.; Boomer, G. Scott; Williams, Byron K.; Nichols, James D.; Case, David J.

2015-01-01

In 1995, the U.S. Fish and Wildlife Service implemented an adaptive harvest management program (AHM) for the sport harvest of midcontinent mallards (Anas platyrhynchos). The program has been successful in reducing long-standing contentiousness in the regulatory process, while integrating science and policy in a coherent, rigorous, and transparent fashion. After 20 years, much has been learned about the relationship among waterfowl populations, their environment, and hunting regulations, with each increment of learning contributing to better management decisions. At the same time, however, much has been changing in the social, institutional, and environmental arenas that provide context for the AHM process. Declines in hunter numbers, competition from more pressing conservation issues, and global-change processes are increasingly challenging waterfowl managers to faithfully reflect the needs and desires of stakeholders, to account for an increasing number of institutional constraints, and to (probabilistically) predict the consequences of regulatory policy in a changing environment. We review the lessons learned from the AHM process so far, and describe emerging challenges and ways in which they may be addressed. We conclude that the practice of AHM has greatly increased an awareness of the roles of social values, trade-offs, and attitudes toward risk in regulatory decision-making. Nevertheless, going forward the waterfowl management community will need to focus not only on the relationships among habitat, harvest, and waterfowl populations, but on the ways in which society values waterfowl and how those values can change over time. 

Harvest maturity and post-processing dip to improve quality of fresh-cut carambola fruit

USDA-ARS?s Scientific Manuscript database

'Arkin' carambola (Averrhoa carambola L.) fruit harvested at color break or full yellow stage were washed with or without an alkaline solution (pH 13.5), cut to 1 cm thick slices, dipped in calcium ascorbate (Ca ASA), ascorbic acid (ASA) or water, and packaged in perforated clamshells for up to 14 d...

Organic Matter Decomposition following Harvesting and Site Preparation of a Forested Wetland

Treesearch

Carl C. Trettin; M. Davidian; M.F. Jurgensen; R. Lea

1996-01-01

Organic matter accumulation is an important process that affects ecosystem function in many northern wetlands. The cotton strip assay (CSA)was used to measure the effect of harvesting and two different site preparation treatments, bedding and trenching, on organic matter decomposition in a forested wetland. A Latin square experimental design was used to determine the...

Timber harvesting, processing, and employment in the Northwest Economic Adjustment Initiative region: changes and economic assistance.

Treesearch

Terry L. Raettig; Harriet H. Christensen

1999-01-01

The Northwest economic adjustment initiative (NWEAI) provides economic assistance to a region including western Washington, western Oregon, and northern California. Timber harvests have fallen markedly in this region since 1990. The forest products industry is the largest manufacturing sector in the region, and employment has followed the downward trend in timber...

Estimated timber harvest by U.S. region and ownership, 1950-2002.

Treesearch

Darius M. Adams; Richard W. Haynes; Adam J. Daigneault

2006-01-01

This publication provides estimates of total softwood and hardwood harvests by region and owner for the United States from 1950 to 2002. These data are generally not available in a consistent fashion and have to be estimated from state-level data, forest resource inventory statistics, and production of forest products. This publication describes the estimation process...

Examination of roundwood utilization rates in West Virginia

Treesearch

Shawn T. Grushecky; Jan Wiedenbeck; Curt C. Hassler

2013-01-01

Forest harvesting is an integral part of the West Virginia forest economy. This component of the supply chain supports a diverse array of primary and secondary processors. A key metric used to describe the efficiency of the roundwood extraction process is the logging utilization factor (LUF). The LUF is one way managers can discern the overall use of harvested...

Soil and water management in the shortleaf pine ecosystem

Treesearch

Edwin L. Miller

1986-01-01

The opportunities for achieving watershed management goals in the process of timber management in the range of shortleaf pine are excellent. Water yield increases may occur with forest harvest but with little or no adverse watershed effects. Peak or flood flows for major storms are little affected by forest harvest. Serious erosion potentials exist when inappropriate...

The Local Food Grower's Behavior during Planning, Growing, Harvesting, and Selling

ERIC Educational Resources Information Center

Gumirakiza, J. Dominique

2016-01-01

This article presents a perspective on the behavior of the local food grower during the market-related decision-making process. The relevant behavior is manifested during the planning, growing, and harvesting and selling phases of the agricultural business cycle. The local food grower faces a set of market alternatives from which, if applying a…

Belowground Nutrient Dynamics Following Three Harvest Intensities on the Pearl River Floodplain, Mississippi

Treesearch

E.B. Schilling; B.G. Lockaby; Robert Rummer

1999-01-01

Abstract: The influence of clear and partial cut harvests on belowground nutrient cycling processes was examined on the Pearl River floodplain, Mississippi. Foci examined by this study included fine root biomass and detritus, fine root production, fine root nutrient contents, soil respiration rates, and microbial biomass C, N, and P during the first...

Diameter sensors for tree-length harvesting systems

Treesearch

T.P. McDonald; Robert B. Rummer; T.E. Grift

2003-01-01

Most cut-to-length (CTL) harvesters provide sensors for measuring diameter of trees as they are cut and processed. Among other uses, this capability provides a data collection tool for marketing of logs in real time. Logs can be sorted and stacked based on up-to-date market information, then transportation systems optimized to route wood to proper destinations at...

50 CFR 23.70 - How can I trade internationally in American alligator and other crocodilian skins, parts, and...

Code of Federal Regulations, 2011 CFR

2011-10-01

..., crusted, tanned, partially tanned, or otherwise processed), including skins of sport-hunted trophies. (2... American alligator. States and Tribes set up and maintain management and harvest programs designed to monitor and protect American alligators from over-harvest. When a State or Tribe with a management program...

7 CFR 457.135 - Onion crop insurance provisions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... digging. A pre-harvest process in which the onion roots are severed from the soil and the onion bulbs laid on the surface of the soil for drying in the field. Non-storage onions. Generally of a Bermuda... that are harvested as a bulb and dried to a lower moisture content, are firmer, have more outer layers...

7 CFR 457.135 - Onion crop insurance provisions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... digging. A pre-harvest process in which the onion roots are severed from the soil and the onion bulbs laid on the surface of the soil for drying in the field. Non-storage onions. Generally of a Bermuda... that are harvested as a bulb and dried to a lower moisture content, are firmer, have more outer layers...

Modeling the effects of harvest alternatives on mitigating oak decline in a Central Hardwood Forest landscape

Treesearch

Wen J. Wang; Hong S. He; Martin A. Spetich; Stephen R. Shifley; Frank R. III Thompson; Jacob S. Fraser

2013-01-01

Oak decline is a process induced by complex interactions of predisposing factors, inciting factors, and contributing factors operating at tree, stand, and landscape scales. It has greatly altered species composition and stand structure in affected areas. Thinning, clearcutting, and group selection are widely adopted harvest alternatives for reducing forest...

Liquid-Desiccant Vapor Separation Reduces the Energy Requirements of Atmospheric Moisture Harvesting.

PubMed

Gido, Ben; Friedler, Eran; Broday, David M

2016-08-02

An innovative atmospheric moisture harvesting system is proposed, where water vapor is separated from the air prior to cooling and condensation. The system was studied using a model that simulates its three interconnected cycles (air, desiccant, and water) over a range of ambient conditions, and optimal configurations are reported for different operation conditions. Model results were compared to specifications of commercial atmospheric moisture harvesting systems and found to represent saving of 5-65% of the electrical energy requirements due to the vapor separation process. We show that the liquid desiccant separation stage that is integrated into atmospheric moisture harvesting systems can work under a wide range of environmental conditions using low grade or solar heating as a supplementary energy source, and that the performance of the combined system is superior.

Fabrication and characterization of a piezoelectric energy harvester with clamped-clamped beams

NASA Astrophysics Data System (ADS)

Cui, Yan; Yu, Menglin; Gao, Shiqiao; Kong, Xiangxin; Gu, Wang; Zhang, Ran; Liu, Bowen

2018-05-01

This work presents a piezoelectric energy harvester with clamped-clamped beams, and it is fabricated with MEMS process. When excited by sinusoidal vibration, the energy harvester has a sharp jumping down phenomenon and the measured frequency responses of the clamped-clamped beams structure show a larger bandwidth which is about 56Hz, more efficient than that with cantilever beams. When the exciting acceleration ac is 12m/s2, the energy harvester achieves to a maximum open-circuit voltage of 94mV on one beam. The load voltage is proportional to the load resistance, and it increased with the increase of load resistance. Connected four beams in series, the output power reaches the maximum value of 730 nW and the optimal load is 15KΩ to one beam.

A batch process micromachined thermoelectric energy harvester: fabrication and characterization

NASA Astrophysics Data System (ADS)

Su, J.; Leonov, V.; Goedbloed, M.; van Andel, Y.; de Nooijer, M. C.; Elfrink, R.; Wang, Z.; Vullers, R. J. M.

2010-10-01

Micromachined thermopiles are considered as a cost-effective solution for energy harvesters working at a small temperature difference and weak heat flows typical for, e.g., the human body. They can be used for powering autonomous wireless sensor nodes in a body area network. In this paper, a micromachined thermoelectric energy harvester with 6 µm high polycrystalline silicon germanium (poly-SiGe) thermocouples fabricated on a 6 inch wafer is presented. An open circuit voltage of 1.49 V and an output power of 0.4 µW can be generated with 3.5 K temperature difference in a model of a wearable micromachined energy harvester of the discussed design, which has a die size of 1.0 mm × 2.5 mm inside a watch-size generator.

Expansion and Harvesting of hMSC-TERT

PubMed Central

Weber, Christian; Pohl, Sebastian; Pörtner, Ralf; Wallrapp, Christine; Kassem, Moustapha; Geigle, Peter; Czermak, Peter

2007-01-01

The expansion of human mesenchymal stem cells as suspension culture by means of spinner flasks and microcarriers, compared to the cultivation in tissue culture flasks, offers the advantage of reducing the requirements of large incubator capacities as well as reducing the handling effort during cultivation and harvesting. Nonporous microcarriers are preferable when the cells need to be kept in viable condition for further applications like tissue engineering or cell therapy. In this study, the qualification of Biosilon, Cytodex 1, Cytodex 3, RapidCell and P102-L for expansion of hMSC-TERT with an associated harvesting process using either trypsin, accutase, collagenase or a trypsin-accutase mixture was investigated. A subsequent adipogenic differentiation of harvested hMSC-TERT was performed in order to observe possible negative effects on their (adipogenic) differentiation potential as a result of the cultivation and harvesting method. The cultivated cells showed an average growth rate of 0.52 d-1. The cells cultivated on Biosilon, RapidCell and P102-L were harvested succesfully achieving high cell yield and vitalities near 100%. This was not the case for cells on Cytodex 1 and Cytodex 3. The trypsin-accutase mix was most effective. After spinner expansion and harvesting the cells were successfully differentiated to adipocytes. PMID:19662126

Design and kinetic analysis of piezoelectric energy harvesters with self-adjusting resonant frequency

NASA Astrophysics Data System (ADS)

Yu-Jen, Wang; Tsung-Yi, Chuang; Jui-Hsin, Yu

2017-09-01

Vibration-based energy harvesters have been developed as power sources for wireless sensor networks. Because the vibration frequency of the environment is varied with surrounding conditions, how to design an adaptive energy harvester is a practical topic. This paper proposes a design for a piezoelectric energy harvester possessing the ability to self-adjust its resonant frequency in rotational environments. The effective length of a trapezoidal cantilever is extended by centrifugal force from a rotating wheel to vary its area moment of inertia. The analytical solution for the natural frequency of the piezoelectric energy harvester was derived from the parameter design process, which could specify a structure approaching resonance at any wheel rotating frequency. The kinetic equation and electrical damping induced by power generation were derived from a Lagrange method and a mechanical-electrical coupling model, respectively. An energy harvester with adequate parameters can generate power at a wide range of car speeds. The output power of an experimental prototype composed of piezoelectric thin films and connected to a 3.3 MΩ external resistor was approximately 70-140 μW at wheel speeds ranging from 200 to 700 RPM. These results demonstrate that the proposed piezoelectric energy harvester can be applied as a power source for the wireless tire pressure monitoring sensor.

A review on energy harvesting approaches for renewable energies from ambient vibrations and acoustic waves using piezoelectricity

NASA Astrophysics Data System (ADS)

Ahmed, Riaz; Mir, Fariha; Banerjee, Sourav

2017-08-01

The principal objective of this article is to categorically review and compare the state of the art vibration based energy harvesting approaches. To evaluate the contemporary methodologies with respect to their physics, average power output and operational frequencies, systematically divided and easy readable tables are presented followed by the description of the energy harvesting methods. Energy harvesting is the process of obtaining electrical energy from the surrounding vibratory mechanical systems through an energy conversion method using smart structures, like, piezoelectric, electrostatic materials. Recent advancements in low power electronic gadgets, micro electro mechanical systems, and wireless sensors have significantly increased local power demand. In order to circumvent the energy demand; to allow limitless power supply, and to avoid chemical waste from conventional batteries, low power local energy harvesters are proposed for harvesting energy from different ambient energy sources. Piezoelectric materials have received tremendous interest in energy harvesting technology due to its unique ability to capitalize the ambient vibrations to generate electric potential. Their crystalline configuration allows the material to convert mechanical strain energy into electrical potential, and vice versa. This article discusses the various approaches in vibration based energy scavenging where piezoelectric materials are employed as the energy conversion medium.

Energy harvesting for dielectric elastomer sensing

NASA Astrophysics Data System (ADS)

Anderson, Iain A.; Illenberger, Patrin; O'Brien, Ben M.

2016-04-01

Soft and stretchy dielectric elastomer (DE) sensors can measure large strains on robotic devices and people. DE strain measurement requires electric energy to run the sensors. Energy is also required for information processing and telemetering of data to phone or computer. Batteries are expensive and recharging is inconvenient. One solution is to harvest energy from the strains that the sensor is exposed to. For this to work the harvester must also be wearable, soft, unobtrusive and profitable from the energy perspective; with more energy harvested than used for strain measurement. A promising way forward is to use the DE sensor as its own energy harvester. Our study indicates that it is feasible for a basic DE sensor to provide its own power to drive its own sensing signal. However telemetry and computation that are additional to this will require substantially more power than the sensing circuit. A strategy would involve keeping the number of Bluetooth data chirps low during the entire period of energy harvesting and to limit transmission to a fraction of the total time spent harvesting energy. There is much still to do to balance the energy budget. This will be a challenge but when we succeed it will open the door to autonomous DE multi-sensor systems without the requirement for battery recharge.

Effects of timber harvests and silvicultural edges on terrestrial salamanders.

PubMed

MacNeil, Jami E; Williams, Rod N

2014-01-01

Balancing timber production and conservation in forest management requires an understanding of how timber harvests affect wildlife species. Terrestrial salamanders are useful indicators of mature forest ecosystem health due to their importance to ecosystem processes and sensitivity to environmental change. However, the effects of timber harvests on salamanders, though often researched, are still not well understood. To further this understanding, we used artificial cover objects to monitor the relative abundance of terrestrial salamanders for two seasons (fall and spring) pre-harvest and five seasons post-harvest in six forest management treatments, and for three seasons post-harvest across the edge gradients of six recent clearcuts. In total, we recorded 19,048 encounters representing nine species of salamanders. We observed declines in mean encounters of eastern red-backed salamanders (Plethodon cinereus) and northern slimy salamanders (P. glutinosus) from pre- to post-harvest in group selection cuts and in clearcuts. However, we found no evidence of salamander declines at shelterwoods and forested sites adjacent to harvests. Edge effects induced by recent clearcuts influenced salamanders for approximately 20 m into the forest, but edge influence varied by slope orientation. Temperature, soil moisture, and canopy cover were all correlated with salamander counts. Our results suggest silvicultural techniques that remove the forest canopy negatively affect salamander relative abundance on the local scale during the years immediately following harvest, and that the depth of edge influence of clearcuts on terrestrial salamanders is relatively shallow (<20 m). Small harvests (<4 ha) and techniques that leave the forest canopy intact may be compatible with maintaining terrestrial salamander populations across a forested landscape. Our results demonstrate the importance of examining species-specific responses and monitoring salamanders across multiple seasons and years. Long-term monitoring will be necessary to understand the full impacts of forest management on terrestrial salamanders.

When can efforts to control nuisance and invasive species backfire?

USGS Publications Warehouse

Zipkin, E.F.; Kraft, C.E.; Cooch, E.G.; Sullivan, P.J.

2009-01-01

Population control through harvest has the potential to reduce the abundance of nuisance and invasive species. However, demographic structure and density-dependent processes can confound removal efforts and lead to undesirable consequences, such as overcompensation (an increase in abundance in response to harvest) and instability (population cycling or chaos). Recent empirical studies have demonstrated the potential for increased mortality (such as that caused by harvest) to lead to overcompensation and instability in plant, insect, and fish populations. We developed a general population model with juvenile and adult stages to help determine the conditions under which control harvest efforts can produce unintended outcomes. Analytical and simulation analyses of the model demonstrated that the potential for overcompensation as a result of harvest was significant for species with high fecundity, even when annual stage-specific survivorship values were fairly low. Population instability as a result of harvest occurred less frequently and was only possible with harvest strategies that targeted adults when both fecundity and adult survivorship were high. We considered these results in conjunction with current literature on nuisance and invasive species to propose general guidelines for assessing the risks associated with control harvest based on life history characteristics of target populations. Our results suggest that species with high per capita fecundity (over discrete breeding periods), short juvenile stages, and fairly constant survivorship rates are most likely to respond undesirably to harvest. It is difficult to determine the extent to which overcompensation and instability could occur during real-world removal efforts, and more empirical removal studies should be undertaken to evaluate population-level responses to control harvests. Nevertheless, our results identify key issues that have been seldom acknowledged and are potentially generic across taxa. ?? 2009 by the Ecological Society ot America.

When can efforts to control nuisance and invasive species backfire?

PubMed

Zipkin, Elise F; Kraft, Clifford E; Cooch, Evan G; Sullivan, Patrick J

2009-09-01

Population control through harvest has the potential to reduce the abundance of nuisance and invasive species. However, demographic structure and density-dependent processes can confound removal efforts and lead to undesirable consequences, such as overcompensation (an increase in abundance in response to harvest) and instability (population cycling or chaos). Recent empirical studies have demonstrated the potential for increased mortality (such as that caused by harvest) to lead to overcompensation and instability in plant, insect, and fish populations. We developed a general population model with juvenile and adult stages to help determine the conditions under which control harvest efforts can produce unintended outcomes. Analytical and simulation analyses of the model demonstrated that the potential for overcompensation as a result of harvest was significant for species with high fecundity, even when annual stage-specific survivorship values were fairly low. Population instability as a result of harvest occurred less frequently and was only possible with harvest strategies that targeted adults when both fecundity and adult survivorship were high. We considered these results in conjunction with current literature on nuisance and invasive species to propose general guidelines for assessing the risks associated with control harvest based on life history characteristics of target populations. Our results suggest that species with high per capita fecundity (over discrete breeding periods), short juvenile stages, and fairly constant survivorship rates are most likely to respond undesirably to harvest. It is difficult to determine the extent to which overcompensation and instability could occur during real-world removal efforts, and more empirical removal studies should be undertaken to evaluate population-level responses to control harvests. Nevertheless, our results identify key issues that have been seldom acknowledged and are potentially generic across taxa.

Wastewater polishing by a channelized macrophyte-dominated wetland and anaerobic digestion of the harvested phytomass.

PubMed

Cohen, Michael F; Hare, Caden; Kozlowski, John; McCormick, Rachel S; Chen, Lily; Schneider, Linden; Parish, Meghan; Knight, Zane; Nelson, Timothy A; Grewell, Brenda J

2013-01-01

Constructed wetlands (CW) offer a mechanism to meet increasingly stringent regulatory standards for wastewater treatment while minimizing energy inputs. Additionally, harvested wetland phytomass subjected to anaerobic digestion can serve as a source of biogas methane. To investigate CW wastewater polishing activities and potential energy yield we constructed a pair of secondary wastewater-fed channelized CW modules designed to retain easily harvestable floating aquatic vegetation and maximize exposure of water to roots and sediment. Modules that were regularly harvested averaged a nitrate removal rate of 1.1 g N m(-2) d(-1); harvesting, sedimentation and gasification were responsible for 30.5%, 8.0% and 61.5% of the N losses, respectively. Selective harvesting of a module to maintain dominance of filamentous algae had no effect on nitrate removal rate but lowered productivity by one-half. The average monthly productivity for unselectively harvested modules was 9.3 ± 1.7 g dry wt. m(-2) d(-1) (±SE). Cessation of harvesting in one module resulted in a significant increase in nitrate removal rate and decrease in phosphate removal rate. Compared to the influent, the effluent of the harvested module had significantly lower levels of estrogenic activity, as determined by a quantitative PCR-based juvenile trout bioassay, and significantly lower densities of E. coli. In mixed vertical-flow reactors anaerobic co-digestion of equal dry weight proportions of harvested aquatic vegetation, wine yeast lees and dairy manure was greatly improved when the manure was replaced with the crude glycerol by-product of biodiesel production. Remaining solids were vermicomposted for use as a soil amendment. Our results indicate that incorporation of constructed wetlands into an integrated treatment system can simultaneously enhance the economic and energetic feasibility of wastewater and organic waste treatment processes.

Effects of Timber Harvests and Silvicultural Edges on Terrestrial Salamanders

PubMed Central

MacNeil, Jami E.; Williams, Rod N.

2014-01-01

Balancing timber production and conservation in forest management requires an understanding of how timber harvests affect wildlife species. Terrestrial salamanders are useful indicators of mature forest ecosystem health due to their importance to ecosystem processes and sensitivity to environmental change. However, the effects of timber harvests on salamanders, though often researched, are still not well understood. To further this understanding, we used artificial cover objects to monitor the relative abundance of terrestrial salamanders for two seasons (fall and spring) pre-harvest and five seasons post-harvest in six forest management treatments, and for three seasons post-harvest across the edge gradients of six recent clearcuts. In total, we recorded 19,048 encounters representing nine species of salamanders. We observed declines in mean encounters of eastern red-backed salamanders (Plethodon cinereus) and northern slimy salamanders (P. glutinosus) from pre- to post-harvest in group selection cuts and in clearcuts. However, we found no evidence of salamander declines at shelterwoods and forested sites adjacent to harvests. Edge effects induced by recent clearcuts influenced salamanders for approximately 20 m into the forest, but edge influence varied by slope orientation. Temperature, soil moisture, and canopy cover were all correlated with salamander counts. Our results suggest silvicultural techniques that remove the forest canopy negatively affect salamander relative abundance on the local scale during the years immediately following harvest, and that the depth of edge influence of clearcuts on terrestrial salamanders is relatively shallow (<20 m). Small harvests (<4 ha) and techniques that leave the forest canopy intact may be compatible with maintaining terrestrial salamander populations across a forested landscape. Our results demonstrate the importance of examining species-specific responses and monitoring salamanders across multiple seasons and years. Long-term monitoring will be necessary to understand the full impacts of forest management on terrestrial salamanders. PMID:25517409

Harvesting of microalgae biomass from the phycoremediation process of greywater.

PubMed

Atiku, Hauwa; Mohamed, R M S R; Al-Gheethi, A A; Wurochekke, A A; Kassim, Amir Hashim M

2016-12-01

The wide application of microalgae in the field of wastewater treatment and bioenergy source has improved research studies in the past years. Microalgae represent a good source of biomass and bio-products which are used in different medical and industrial activities, among them the production of high-valued products and biofuels. The present review focused on greywater treatment through the application of phycoremediation technique with microalgae and presented recent advances in technologies used for harvesting the microalgae biomass. The advantages and disadvantages of each method are discussed. The microbiological aspects of production, harvesting and utilization of microalgae biomass are viewed.

19 CFR 10.530 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-04-01

... of the following processes: Welding, flame spraying, surface machining, knurling, plating, sleeving...” means a person who grows, raises, mines, harvests, fishes, traps, hunts, manufactures, processes...

Modeling the Emergent Impacts of Harvesting Acadian Forests over 100+ Years

NASA Astrophysics Data System (ADS)

Luus, K. A.; Plug, L. J.

2007-12-01

Harvesting strategies and policies for Acadian forest in Nova Scotia, Canada, presently are set using Decision Support Models (DSMs) that aim to maximize the long-term (>100y) value of forests through decisions implemented over short time horizons (5-80 years). However, DSMs typically are aspatial, lack ecological processes and do not treat erosion, so the long-term (>100y) emergent impacts of the prescribed forestry decisions on erosion and vegetation in Acadian forests remain poorly known. To better understand these impacts, we created an equation-based model that simulates the evolution of a ≥4 km2 forest in time steps of 1 y and at a spatial resolution of 3 m2, the footprint of a single mature tree. The model combines 1) ecological processes of recruitment, competition, and mortality; 2) geomorphic processes of hillslope erosion; 3) anthropic processes of tree harvesting, replanting, and road construction under constraints imposed by regulations and cost/benefit ratio. The model uses digital elevation models, parameters (where available), and calibration (where measurements are not available) for conditions presently found in central Cape Breton, Nova Scotia. The model is unique because it 1) deals with the impacts of harvesting on an Acadian forest; and 2) vegetation and erosion are coupled. The model was tested by comparing the species-specific biomass of long-term (40 y) forest plot data to simulated results. At the spatial scale of individual 1 ha plots, model predictions presently account for approximately 50% of observed biomass changes through time, but predictions are hampered by the effects of serendipitous "random" events such as single tree windfall. Harvesting increases the cumulative erosion over 3000 years by 240% when compared to an old growth forest and significantly suppresses the growth of Balsam Fir and Sugar Maple. We discuss further tests of the model, and how it might be used to investigate the long-term sustainability of the recommendations made by DSMs and to better understand the relationship between vegetation, erosion, and forest management strategies.

Insights from Placing Photosynthetic Light Harvesting into Context.

PubMed

Demmig-Adams, Barbara; Stewart, Jared J; Burch, Tyson A; Adams, William W

2014-08-21

Solar-energy conversion through natural photosynthesis forms the base of virtually all food chains on Earth and provides fiber, materials, and fuels, as well as inspiration for the design of biomimetic energy-conversion systems. We summarize well-known as well as recently discovered feedback loops between natural light-harvesting systems and whole-organism function in natural settings. We propose that the low effective quantum yield of natural light-harvesting systems in high light is caused by downstream limitations rather than unavoidable intrinsic vulnerabilities. We evaluate potential avenues, and their costs and benefits, for increasing the maximal rate and photon yield of photosynthesis in high light in plants and photosynthetic microbes. By summarizing mechanisms observable only in complex systems (whole plants, algae, or, in some cases, intact leaves), we aim to stimulate future research efforts on reciprocal feedback loops between light harvesting and downstream processes in whole organisms and to provide additional arguments for the significance of research on photosynthetic light harvesting.

Folate content in strawberries (Fragaria x ananassa): effects of cultivar, ripeness, year of harvest, storage, and commercial processing.

PubMed

Strålsjö, Lena M; Witthöft, Cornelia M; Sjöholm, Ingegerd M; Jägerstad, Margaretha I

2003-01-01

Folate concentrations in strawberries and folate retention during storage and commercial processing of strawberries were investigated. No previous study has focused on the effects of cultivar, ripeness, and year of harvest of strawberries with respect to the folate content. This study showed the folate concentration in strawberries to significantly depend on all of these different factors. Total folate was quantified using a modified and validated radioprotein-binding assay with external calibration (5-CH(3)-H(4)folate). Folate content in 13 different strawberry cultivars varied from 335 microg/100 g of dry matter (DM) for cv. Senga Sengana to 644 microg/100 g of DM for cv. Elsanta. Swedish harvests from 1999 and 2001 yielded higher folate concentrations than did the harvest from 2000, and the grade of ripeness affected the folate content in strawberries. This study indicated high folate retention in intact berries during storage until 3 or 9 days at 4 degrees C (71-99%) and also in most tested commercial products (79-103%). On the basis of these data fresh strawberries as well as processed strawberry products are recommended to be good folate sources. For instance, 250 g (fresh weight) of strawberries ( approximately 125 microg of folate) supplies approximately 50% of the recommended daily folate intake in various European countries (200-300 microg/day) or 30% of the U.S. recommendation (400 microg/day).

Historical harvests reduce neighboring old-growth basal area across a forest landscape.

PubMed

Bell, David M; Spies, Thomas A; Pabst, Robert

2017-07-01

While advances in remote sensing have made stand, landscape, and regional assessments of the direct impacts of disturbance on forests quite common, the edge influence of timber harvesting on the structure of neighboring unharvested forests has not been examined extensively. In this study, we examine the impact of historical timber harvests on basal area patterns of neighboring old-growth forests to assess the magnitude and scale of harvest edge influence in a forest landscape of western Oregon, USA. We used lidar data and forest plot measurements to construct 30-m resolution live tree basal area maps in lower and middle elevation mature and old-growth forests. We assessed how edge influence on total, upper canopy, and lower canopy basal area varied across this forest landscape as a function of harvest characteristics (i.e., harvest size and age) and topographic conditions in the unharvested area. Upper canopy, lower canopy, and total basal area increased with distance from harvest edge and elevation. Forests within 75 m of harvest edges (20% of unharvested forests) had 4% to 6% less live tree basal area compared with forest interiors. An interaction between distance from harvest edge and elevation indicated that elevation altered edge influence in this landscape. We observed a positive edge influence at low elevations (<800 m) and a negative edge influence at moderate to high elevations (>800 m). Surprisingly, we found no or weak effects of harvest age (13-60 yr) and harvest area (0.2-110 ha) on surrounding unharvested forest basal area, implying that edge influence was relatively insensitive to the scale of disturbance and multi-decadal recovery processes. Our study indicates that the edge influence of past clearcutting on the structure of neighboring uncut old-growth forests is widespread and persistent. These indirect and diffuse legacies of historical timber harvests complicate forest management decision-making in old-growth forest landscapes by broadening the traditional view of stand boundaries. Furthermore, the consequences of forest harvesting may reach across ownership boundaries, highlighting complex governance issues surrounding landscape management of old-growth forests. © 2017 by the Ecological Society of America.

Application of the OCRA Method in the sugar cane harvest and its repercussion on the workers' health. Preliminary study.

PubMed

Ruddy, Facci; Eduardo, Marcatto; Edoardo, Santino

2012-01-01

In Brazil the sugar ethanol industry has had strong growth in the last 10 years, sometimes due to the growing sugar exportation, sometimes due to the alcohol production for automobile fuel and for exportation. Despite the growing mechanization of the raw material harvest (sugar cane), the manual work still persists. The development of this article was based in the application of the OCRA Method in the sugar cane harvesting process, to evaluate the risks to the upper limbs by repetitive movements and epidemiologically prove the ratio risk x harm to the heath of the workers, as well as the probability of developing improvements in the working conditions. The analysis process consists of studying the work organization, the risks to the health of the worker and the distribution of the recovery periods during the working day.

The need for coherence between waterfowl harvest and habitat management

USGS Publications Warehouse

Runge, M.C.; Johnson, F.A.; Anderson, M.G.; Koneff, M.D.; Reed, E.T.; Mott, S.E.

2006-01-01

Two of the most significant management efforts affecting waterfowl populations in North America are the North American Waterfowl Management Plan (the Plan) and Federal harvest management programs. Both the Plan and harvest management are continental in scope, involve an extensive group of stakeholders, and rely on adaptive processes of biological planning, implementation, and evaluation. The development of these programs has occurred independently, however, and there has been little explicit recognition that both harvest and habitat effects should be considered for coherent management planning and evaluation. For example, the harvest strategy can affect whether population objectives of the Plan are met, irrespective of the success of the Plan's habitat conservation efforts. Conversely, habitat conservation activities under the Plan can influence harvest potential and, therefore, the amount of hunting opportunity provided. It seems increasingly clear that the Plan's waterfowl population objectives can only be useful for conservation planning and evaluation if they are accompanied by an explicit specification of the harvest strategy and environmental conditions under which they are to be achieved. This clarification also is necessary to ensure that Plan population objectives are not attained solely through the reduction of hunting opportunity. We believe then that it is imperative that these key waterfowl-management programs work to harmonize their objectives. Harvest management programs and the Plan ought to be working toward the same ends, but that is not possible so long as the mutually reinforcing relationship of these programs is obscured by ambiguities in their management objectives.

Harvest maturity, pre-cutting wash and post-processing dip to improve quality of fresh-cut carambola fruit

USDA-ARS?s Scientific Manuscript database

‘Arkin’ carambola (Averrhoa carambola L.) fruit harvested at color break or full yellow stage were washed with or without an alkaline solution (pH 12), cut to 10 mm slices, dipped in calcium ascorbate (Ca ASA), ascorbic acid (ASA) or water, and packaged in perforated clamshells for up to 14 days sto...

PROGRESS IN MEETING PROBLEMS OF MIGRATORY LABOR IN MARYLAND, FOURTH ANNUAL REPORT.

ERIC Educational Resources Information Center

NYSTROM, PAUL E.; AND OTHERS

THE VEGETABLE AND FRUIT INDUSTRIES OF MARYLAND HAVE LONG BEEN DEPENDENT UPON MIGRATORY LABOR FOR THE SEASONAL LABOR REQUIRED IN HARVESTING AND PROCESSING OPERATIONS. THIS LABOR FORCE COMES TO THE STATE IN THE SPRING OR SUMMER, IS EMPLOYED IN VARIOUS CAMPS IN MARYLAND AND STATES IN THE NORTH, AND MIGRATES SOUTH FOLLOWING THE HARVEST OF LATE…

California’s forest products industry and timber harvest, 2006

Treesearch

Todd A. Morgan; Jason P. Brandt; Kathleen E. Songster; Charles E. Keegan; Glenn A. Christensen

2012-01-01

This report traces the flow of California’s 2006 timber harvest through the primary wood products industry (i.e., firms that process timber into manufactured products such as lumber, as well as facilities such as pulp mills and particleboard plants, which use the wood fiber or mill residue directly from timber processors) and provides a description of the structure,...

Importance of succession, harvest, and climate change in determining future composition in US Central Hardwood Forests

Treesearch

Wen J. Wang; Hong S. He; Frank R. Thompson; Jacob S. Fraser; Brice B. Hanberry; William D. Dijak

2015-01-01

Most temperate forests in U.S. are recovering from heavy exploitation and are in intermediate successional stages where partial tree harvest is the primary disturbance. Changes in regional forest composition in response to climate change are often predicted for plant functional types using biophysical process models. These models usually simplify the simulation of...

Prevalence of Escherichia coli 0157:H7 and Salmonella in camel, cattle, goat and sheep harvested for meat in Riyadh

USDA-ARS?s Scientific Manuscript database

Escherichia coli O157:H7 and Salmonella are significant foodborne pathogens that can be found in the feces and on the hides of meat animals. When hides are removed during the harvest process, the carcass and subsequent meat products can become contaminated. Camels, cattle, sheep and goats are harve...

77 FR 10668 - Fisheries of the Northeastern United States; Atlantic Herring Fishery; Sub-ACL (Annual Catch...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-23

...-ACL (Annual Catch Limit) Harvested for Management Area 2 AGENCY: National Marine Fisheries Service... biological catch, annual catch limit (ACL), optimum yield, domestic harvest and processing, U.S. at-sea...,200 metric tons (mt); the 2012 sub-ACL allocated to Area 2 is 22,146 mt, and 0 mt of the sub-ACL is...

Comparison of different options for harvest of a therapeutic protein product from high cell density yeast fermentation broth.

PubMed

Wang, Alice; Lewus, Rachael; Rathore, Anurag S

2006-05-05

Recovery of therapeutic protein from high cell density yeast fermentations at commercial scale is a challenging task. In this study, we investigate and compare three different harvest approaches, namely centrifugation followed by depth filtration, centrifugation followed by filter-aid enhanced depth filtration, and microfiltration. This is achieved by presenting a case study involving recovery of a therapeutic protein from Pichia pastoris fermentation broth. The focus of this study is on performance of the depth filtration and the microfiltration steps. The experimental data has been fitted to the conventional models for cake filtration to evaluate specific cake resistance and cake compressibility. In the case of microfiltration, the experimental data agrees well with flux predicted by shear induced diffusion model. It is shown that, under optimal conditions, all three options can deliver the desired product recovery ( >80%), harvest time ( <15 h including sequential concentration/diafiltration step), and clarification ( <6 NTU). However, the three options differ in terms of process development time required, capital cost, consumable cost, ease of scale-ability and process robustness. It is recommended that these be kept under consideration when making a final decision on a harvesting approach.

Differential deposition of H2A.Z in rice seedling tissue during the day-night cycle.

PubMed

Zhang, Kang; Xu, Wenying; Wang, Chunchao; Yi, Xin; Su, Zhen

2017-03-04

Chromatin structure has an important role in modulating gene expression. The incorporation of histone variants into the nucleosome leads to important changes in the chromatin structure. The histone variant H2A.Z is highly conserved between different species of fungi, animals, and plants. However, dynamic changes to H2A.Z in rice have not been reported during the day-night cycle. In this study, we generated genome wide maps of H2A.Z for day and night time in harvested seedling tissues by combining chromatin immunoprecipitation and high-throughput sequencing. The analysis results for the H2A.Z data sets detected 7099 genes with higher depositions of H2A.Z in seedling tissues harvested at night compared with seedling tissues harvested during the day, whereas 4597 genes had higher H2A.Z depositions in seedlings harvested during the day. The gene expression profiles data suggested that H2A.Z probably negatively regulated gene expression during the day-night cycle and was involved in many important biologic processes. In general, our results indicated that H2A.Z may play an important role in plant responses to the diurnal oscillation process.

Design and experimental evaluation on an advanced multisource energy harvesting system for wireless sensor nodes.

PubMed

Li, Hao; Zhang, Gaofei; Ma, Rui; You, Zheng

2014-01-01

An effective multisource energy harvesting system is presented as power supply for wireless sensor nodes (WSNs). The advanced system contains not only an expandable power management module including control of the charging and discharging process of the lithium polymer battery but also an energy harvesting system using the maximum power point tracking (MPPT) circuit with analog driving scheme for the collection of both solar and vibration energy sources. Since the MPPT and the power management module are utilized, the system is able to effectively achieve a low power consumption. Furthermore, a super capacitor is integrated in the system so that current fluctuations of the lithium polymer battery during the charging and discharging processes can be properly reduced. In addition, through a simple analog switch circuit with low power consumption, the proposed system can successfully switch the power supply path according to the ambient energy sources and load power automatically. A practical WSNs platform shows that efficiency of the energy harvesting system can reach about 75-85% through the 24-hour environmental test, which confirms that the proposed system can be used as a long-term continuous power supply for WSNs.

Design and Experimental Evaluation on an Advanced Multisource Energy Harvesting System for Wireless Sensor Nodes

PubMed Central

Li, Hao; Zhang, Gaofei; Ma, Rui; You, Zheng

2014-01-01

An effective multisource energy harvesting system is presented as power supply for wireless sensor nodes (WSNs). The advanced system contains not only an expandable power management module including control of the charging and discharging process of the lithium polymer battery but also an energy harvesting system using the maximum power point tracking (MPPT) circuit with analog driving scheme for the collection of both solar and vibration energy sources. Since the MPPT and the power management module are utilized, the system is able to effectively achieve a low power consumption. Furthermore, a super capacitor is integrated in the system so that current fluctuations of the lithium polymer battery during the charging and discharging processes can be properly reduced. In addition, through a simple analog switch circuit with low power consumption, the proposed system can successfully switch the power supply path according to the ambient energy sources and load power automatically. A practical WSNs platform shows that efficiency of the energy harvesting system can reach about 75–85% through the 24-hour environmental test, which confirms that the proposed system can be used as a long-term continuous power supply for WSNs. PMID:25032233

Making do with less: Must sparse data preclude informed harvest strategies for European waterbirds?

USGS Publications Warehouse

Johnson, Fred A.; Alhainen, Mikko; Fox, Anthony D.; Madsen, Jesper; Guillemain, Matthieu

2018-01-01

The demography of many European waterbirds is not well understood because most countries have conducted little monitoring and assessment, and coordination among countries on waterbird management has little precedent. Yet intergovernmental treaties now mandate the use of sustainable, adaptive harvest strategies, whose development is challenged by a paucity of demographic information. In this study, we explore how a combination of allometric relationships, fragmentary monitoring and research information, and expert judgment can be used to estimate the parameters of a theta-logistic population model, which in turn can be used in a Markov decision process to derive optimal harvesting strategies. We show how to account for considerable parametric uncertainty, as well as for different management objectives. We illustrate our methodology with a poorly understood population of taiga bean geese (Anser fabalis fabalis), which is a popular game bird in Fennoscandia. Our results for taiga bean geese suggest that they may have demographic rates similar to other, well-studied species of geese, and our model-based predictions of population size are consistent with the limited monitoring information available. Importantly, we found that by using a Markov decision process, a simple scalar population model may be sufficient to guide harvest management of this species, even if its demography is age-structured. Finally, we demonstrated how two different management objectives can lead to very different optimal harvesting strategies, and how conflicting objectives may be traded off with each other. This approach will have broad application for European waterbirds by providing preliminary estimates of key demographic parameters, by providing insights into the monitoring and research activities needed to corroborate those estimates, and by producing harvest management strategies that are optimal with respect to the managers’ objectives, options, and available demographic information.

Influence of Harvest Aid Herbicides on Seed Germination, Seedling Vigor and Milling Quality Traits of Red Lentil (Lens culinaris L.).

PubMed

Subedi, Maya; Willenborg, Christian J; Vandenberg, Albert

2017-01-01

Most red lentil produced worldwide is consumed in dehulled form, and post-harvest milling and splitting qualities are major concerns in the secondary processing industry. Lentil producers in northern temperate regions usually apply pre-harvest desiccants as harvest aids to accelerate the lentil crop drying process and facilitate harvesting operations. This paper reports on field studies conducted at Scott and Saskatoon, Saskatchewan, Canada in the 2012 and 2013 cropping seasons to evaluate whether herbicides applied as harvest aids alone or tank mixed with glyphosate affect seed germination, seedling vigor, milling, and splitting qualities. The site-year by desiccant treatment interaction for seed germination, vigor, and milling recovery yields was significant. Glyphosate applied alone or as tank mix with other herbicides (except diquat) reduced seed germination and seedling vigor at Saskatoon and Scott in 2012 only. Pyraflufen-ethyl (20 g ai ha -1 ) applied with glyphosate as well as saflufenacil (36 g ai ha -1 ) decreased dehulling efficiency, while saflufenacil and/or glufosinate with glyphosate reduced milling recovery and football recovery, although these effects were inconsistent. Application of diquat alone or in combination with glyphosate exhibited more consistent dehulling efficiency gains and increases in milling recovery yield. Significant but negative associations were observed between glyphosate residue in seeds and seed germination ( r = -0.84, p < 0.001), seed vigor ( r = -0.62, p < 0.001), dehulling efficiency ( r = -0.55, p < 0.001), and milling recovery ( r = -0.62, p < 0.001). These results indicate application of diquat alone or in combination with glyphosate may be a preferred option for lentil growers to improve milling recovery yield.

Influence of Harvest Aid Herbicides on Seed Germination, Seedling Vigor and Milling Quality Traits of Red Lentil (Lens culinaris L.)

PubMed Central

Subedi, Maya; Willenborg, Christian J.; Vandenberg, Albert

2017-01-01

Most red lentil produced worldwide is consumed in dehulled form, and post-harvest milling and splitting qualities are major concerns in the secondary processing industry. Lentil producers in northern temperate regions usually apply pre-harvest desiccants as harvest aids to accelerate the lentil crop drying process and facilitate harvesting operations. This paper reports on field studies conducted at Scott and Saskatoon, Saskatchewan, Canada in the 2012 and 2013 cropping seasons to evaluate whether herbicides applied as harvest aids alone or tank mixed with glyphosate affect seed germination, seedling vigor, milling, and splitting qualities. The site-year by desiccant treatment interaction for seed germination, vigor, and milling recovery yields was significant. Glyphosate applied alone or as tank mix with other herbicides (except diquat) reduced seed germination and seedling vigor at Saskatoon and Scott in 2012 only. Pyraflufen-ethyl (20 g ai ha−1) applied with glyphosate as well as saflufenacil (36 g ai ha−1) decreased dehulling efficiency, while saflufenacil and/or glufosinate with glyphosate reduced milling recovery and football recovery, although these effects were inconsistent. Application of diquat alone or in combination with glyphosate exhibited more consistent dehulling efficiency gains and increases in milling recovery yield. Significant but negative associations were observed between glyphosate residue in seeds and seed germination (r = −0.84, p < 0.001), seed vigor (r = −0.62, p < 0.001), dehulling efficiency (r = −0.55, p < 0.001), and milling recovery (r = −0.62, p < 0.001). These results indicate application of diquat alone or in combination with glyphosate may be a preferred option for lentil growers to improve milling recovery yield. PMID:28352275

A seesaw-type approach for enhancing nonlinear energy harvesting

NASA Astrophysics Data System (ADS)

Deng, Huaxia; Wang, Zhemin; Du, Yu; Zhang, Jin; Ma, Mengchao; Zhong, Xiang

2018-05-01

Harvesting sustainable mechanical energy is the ultimate objective of nonlinear energy harvesters. However, overcoming potential barriers, especially without the use of extra excitations, poses a great challenge for the development of nonlinear generators. In contrast to the existing methods, which typically modify the barrier height or utilize additional excitations, this letter proposes a seesaw-type approach to facilitate escape from potential wells by transfer of internal energy, even under low-intensity excitation. This approach is adopted in the design of a seesaw-type nonlinear piezoelectric energy harvester and the energy transfer process is analyzed by deriving expressions for the energy to reveal the working mechanism. Comparison experiments demonstrate that this approach improves energy harvesting in terms of an increase in the working frequency bandwidth by a factor of 60.14 and an increase in the maximum output voltage by a factor of 5.1. Moreover, the output power is increased by a factor of 51.3, which indicates that this approach significantly improves energy collection efficiency. This seesaw-type approach provides a welcome boost to the development of renewable energy collection methods by improving the efficiency of harvesting of low-intensity ambient mechanical energy.

Automatic poisson peak harvesting for high throughput protein identification.

PubMed

Breen, E J; Hopwood, F G; Williams, K L; Wilkins, M R

2000-06-01

High throughput identification of proteins by peptide mass fingerprinting requires an efficient means of picking peaks from mass spectra. Here, we report the development of a peak harvester to automatically pick monoisotopic peaks from spectra generated on matrix-assisted laser desorption/ionisation time of flight (MALDI-TOF) mass spectrometers. The peak harvester uses advanced mathematical morphology and watershed algorithms to first process spectra to stick representations. Subsequently, Poisson modelling is applied to determine which peak in an isotopically resolved group represents the monoisotopic mass of a peptide. We illustrate the features of the peak harvester with mass spectra of standard peptides, digests of gel-separated bovine serum albumin, and with Escherictia coli proteins prepared by two-dimensional polyacrylamide gel electrophoresis. In all cases, the peak harvester proved effective in its ability to pick similar monoisotopic peaks as an experienced human operator, and also proved effective in the identification of monoisotopic masses in cases where isotopic distributions of peptides were overlapping. The peak harvester can be operated in an interactive mode, or can be completely automated and linked through to peptide mass fingerprinting protein identification tools to achieve high throughput automated protein identification.

Interaction of side-by-side fluidic harvesters in fractal grid-generated turbulence

NASA Astrophysics Data System (ADS)

Ferko, Kevin; Lachendro, David; Chiappazzi, Nick; Danesh-Yazdi, Amir H.

2018-03-01

While the vast majority of the literature in energy harvesting is dedicated to resonant harvesters, non-resonant harvesters, especially those that use turbulence-induced vibration to generate energy, have not been studied in as much detail. This is especially true for grid-generated turbulence. In this paper, the interaction of two side-by-side fluidic harvesters from a passive fractal grid-generated turbulent flow is considered. The fractal grid has been shown to significantly increase the turbulence generated in the flow which is the source of the vibration of the piezoelectric beams. In this experimental study, the influence of four parameters has been investigated: Beam lengths and configurations, mean flow velocity, distance from the grid and gap between the two beams. Experimental results show that the piezoelectric harvesters in fractal grid turbulence are capable of producing at least the same amount of power as those placed in passive rectangular grids with a larger pressure loss, allowing for a potentially significant increase in the efficiency of the energy conversion process, even though more experiments are required to study the behavior of the beams in homogeneous, fractal grid-generated turbulence.

Acid-Catalyzed Algal Biomass Pretreatment for Integrated Lipid and Carbohydrate-Based Biofuels Production

DOE PAGES

Laurens, L. M. L.; Nagle, N.; Davis, R.; ...

2014-11-12

One of the major challenges associated with algal biofuels production in a biorefinery-type setting is improving biomass utilization in its entirety, increasing the process energetic yields and providing economically viable and scalable co-product concepts. We demonstrate the effectiveness of a novel, integrated technology based on moderate temperatures and low pH to convert the carbohydrates in wet algal biomass to soluble sugars for fermentation, while making lipids more accessible for downstream extraction and leaving a protein-enriched fraction behind. We studied the effect of harvest timing on the conversion yields, using two algal strains; Chlorella and Scenedesmus, generating biomass with distinctive compositionalmore » ratios of protein, carbohydrate, and lipids. We found that the late harvest Scenedesmus biomass had the maximum theoretical biofuel potential at 143 gasoline gallon equivalent (GGE) combined fuel yield per dry ton biomass, followed by late harvest Chlorella at 128 GGE per ton. Our experimental data show a clear difference between the two strains, as Scenedesmus was more successfully converted in this process with a demonstrated 97 GGE per ton. Our measurements indicated a release of >90% of the available glucose in the hydrolysate liquors and an extraction and recovery of up to 97% of the fatty acids from wet biomass. Techno-economic analysis for the combined product yields indicates that this process exhibits the potential to improve per-gallon fuel costs by up to 33% compared to a lipids-only process for one strain, Scenedesmus, grown to the mid-point harvest condition.« less

Tryptanthrin content in Isatis tinctoria leaves--a comparative study of selected strains and post-harvest treatments.

PubMed

Oberthür, Christine; Hamburger, Matthias

2004-07-01

Tryptanthrin is a pharmacologically active compound in the anti-inflammatory herb Isatis tinctoria, with potent inhibitory activity on prostaglandin and leukotriene synthesis and on inducible NO synthase. The tryptanthrin content of five defined woad strains was analyzed in dependence of the time of harvest and post-harvest treatment. Tryptanthrin was determined by a validated ESI-LC-MS isotope dilution assay with d(8)-tryptanthrin as internal standard. The tryptanthrin concentration in freeze-dried leaf samples was low. Drying at ambient temperature led to a significant increase of tryptanthrin concentration, but the highest concentrations were found when leaves were dried at 40 degrees C. Tryptanthrin content in fermented woad leaves was below the limit of quantification. Tryptanthrin appears thus to be a product of post-harvest processes, but details of its formation remain to be elucidated.

Light absorption and excitation energy transfer calculations in primitive photosynthetic bacteria

NASA Astrophysics Data System (ADS)

Komatsu, Yu; Kayanuma, Megumi; Shoji, Mitsuo; Yabana, Kazuhiro; Shiraishi, Kenji; Umemura, Masayuki

2015-06-01

In photosynthetic organisms, light energy is converted into chemical energy through the light absorption and excitation energy transfer (EET) processes. These processes start in light-harvesting complexes, which contain special photosynthetic pigments. The exploration of unique mechanisms in light-harvesting complexes is directly related to studies, such as artificial photosynthesis or biosignatures in astrobiology. We examined, through ab initio calculations, the light absorption and EET processes using cluster models of light-harvesting complexes in purple bacteria (LH2). We evaluated absorption spectra and energy transfer rates using the LH2 monomer and dimer models to reproduce experimental results. After the calibration tests, a LH2 aggregation model, composed of 7 or 19 LH2s aligned in triangle lattice, was examined. We found that the light absorption is red shifted and the energy transfer becomes faster as the system size increases. We also found that EET is accelerated by exchanging the central pigments to lower energy excited pigments. As an astrobiological application, we calculated light absorptions efficiencies of the LH2 in different photoenvironments.

Biomass Supply Logistics and Infrastructure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sokhansanj, Shahabaddine

2009-04-01

Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the Biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews methods of estimating the quantities of biomass followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal withmore » seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and Transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.« less

Biomass supply logistics and infrastructure.

PubMed

Sokhansanj, Shahabaddine; Hess, J Richard

2009-01-01

Feedstock supply system encompasses numerous unit operations necessary to move lignocellulosic feedstock from the place where it is produced (in the field or on the stump) to the start of the conversion process (reactor throat) of the biorefinery. These unit operations, which include collection, storage, preprocessing, handling, and transportation, represent one of the largest technical and logistics challenges to the emerging lignocellulosic biorefining industry. This chapter briefly reviews the methods of estimating the quantities of biomass, followed by harvesting and collection processes based on current practices on handling wet and dry forage materials. Storage and queuing are used to deal with seasonal harvest times, variable yields, and delivery schedules. Preprocessing can be as simple as grinding and formatting the biomass for increased bulk density or improved conversion efficiency, or it can be as complex as improving feedstock quality through fractionation, tissue separation, drying, blending, and densification. Handling and transportation consists of using a variety of transport equipment (truck, train, ship) for moving the biomass from one point to another. The chapter also provides typical cost figures for harvest and processing of biomass.

Fuzzy and process modelling of contour ridge water dynamics

NASA Astrophysics Data System (ADS)

Mhizha, Alexander; Ndiritu, John

2018-05-01

Contour ridges are an in-situ rainwater harvesting technology developed initially for soil erosion control but are currently also widely promoted for rainwater harvesting. The effectiveness of contour ridges depends on geophysical, hydro-climatic and socio economic factors that are highly varied in time and space. Furthermore, field-scale data on these factors are often unavailable. This together with the complexity of hydrological processes at field scale limits the application of classical distributed process modelling to highly-instrumented experimental fields. This paper presents a framework that combines fuzzy logic and process-based approach for modelling contour ridges for rainwater harvesting where detailed field data are not available. Water balance for a representative contour-ridged field incorporating the water flow processes across the boundaries is integrated with fuzzy logic to incorporate the uncertainties in estimating runoff. The model is tested using data collected during the 2009/2010 and 2010/2011 rainfall seasons from two contour-ridged fields in Zhulube located in the semi-arid parts of Zimbabwe. The model is found to replicate soil moisture in the root zone reasonably well (NSE = 0.55 to 0.66 and PBIAS = -1.3 to 6.1 %). The results show that combining fuzzy logic and process based approaches can adequately model soil moisture in a contour ridged-field and could help to assess the water dynamics in contour ridged fields.

Implication of Abscisic Acid on Ripening and Quality in Sweet Cherries: Differential Effects during Pre- and Post-harvest

PubMed Central

Tijero, Verónica; Teribia, Natalia; Muñoz, Paula; Munné-Bosch, Sergi

2016-01-01

Sweet cherry, a non-climacteric fruit, is usually cold-stored during post-harvest to prevent over-ripening. The aim of the study was to evaluate the role of abscisic acid (ABA) on fruit growth and ripening of this fruit, considering as well its putative implication in over-ripening and effects on quality. We measured the endogenous concentrations of ABA during the ripening of sweet cherries (Prunus avium L. var. Prime Giant) collected from orchard trees and in cherries exposed to 4°C and 23°C during 10 days of post-harvest. Furthermore, we examined to what extent endogenous ABA concentrations were related to quality parameters, such as fruit biomass, anthocyanin accumulation and levels of vitamins C and E. Endogenous concentrations of ABA in fruits increased progressively during fruit growth and ripening on the tree, to decrease later during post-harvest at 23°C. Cold treatment, however, increased ABA levels and led to an inhibition of over-ripening. Furthermore, ABA levels positively correlated with anthocyanin and vitamin E levels during pre-harvest, but not during post-harvest. We conclude that ABA plays a major role in sweet cherry development, stimulating its ripening process and positively influencing quality parameters during pre-harvest. The possible influence of ABA preventing over-ripening in cold-stored sweet cherries is also discussed. PMID:27200070

Energy harvesting by means of flow-induced vibrations on aerospace vehicles

NASA Astrophysics Data System (ADS)

Li, Daochun; Wu, Yining; Da Ronch, Andrea; Xiang, Jinwu

2016-10-01

This paper reviews the design, implementation, and demonstration of energy harvesting devices that exploit flow-induced vibrations as the main source of energy. Starting with a presentation of various concepts of energy harvesters that are designed to benefit from a general class of flow-induced vibrations, specific attention is then given at those technologies that may offer, today or in the near future, a potential benefit to extend the operational capabilities and to monitor critical parameters of unmanned aerial vehicles. Various phenomena characterized by flow-induced vibrations are discussed, including limit cycle oscillations of plates and wing sections, vortex-induced and galloping oscillations of bluff bodies, vortex-induced vibrations of downstream structures, and atmospheric turbulence and gusts. It was found that linear or linearized modeling approaches are commonly employed to support the design phase of energy harvesters. As a result, highly nonlinear and coupled phenomena that characterize flow-induced vibrations are neglected in the design process. The Authors encourage a shift in the current design paradigm: considering coupled nonlinear phenomena, and adequate modeling tools to support their analysis, from a design limitation to a design opportunity. Special emphasis is placed on identifying designs and implementations applicable to aircraft configurations. Application fields of flow-induced vibrations-based energy harvesters are discussed including power supply for wireless sensor networks and simultaneous energy harvest and control. A large body of work on energy harvesters is included in this review journal. Whereas most of the references claim direct applications to unmanned aerial vehicles, it is apparent that, in most of the cases presented, the working principles and characteristics of the energy harvesters are incompatible with any aerospace applications. Finally, the challenges that hold back the integration of energy harvesting technologies in the aerospace field are discussed.

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

Arabidopsis thaliana plants are seen inside the growth chamber of the Advanced Plant Habitat (APH) Flight Unit No. 1 prior to harvest of half the plants. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in NASA Kennedy Space Center's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Distribution of Slash and Litter After Wet- and Dry-Site Harvesting of Loblolly Pine Plantations

Treesearch

Mark H. Eisenbies; James A. Burger; Yi-Jun Xu; Steve Patterson

2002-01-01

Displacement of logging slash and forest floor litter in the process of harvesting can interfere with forest nutrient cycling and can modify soil climate in ways that could affect regeneration success and forest productivity. The objective of this study was to assess a visual method for estimating organic matter and slash biomass residues following a typical feller-...

76 FR 66654 - Fisheries of the Northeastern United States; Atlantic Herring Fishery; Sub-ACL (Annual Catch...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-10-27

...; Sub-ACL (Annual Catch Limit) Harvested for Management Area 1A AGENCY: National Marine Fisheries... biological catch, annual catch limit (ACL), optimum yield, domestic harvest and processing, U.S. at-sea...,200 metric tons (mt); the 2011 sub-ACL allocated to Area 1A is 26,546 mt, and 0 mt of the sub-ACL is...

Harvesting interacts with climate change to affect future habitat quality of a focal species in eastern Canada’s boreal forest

PubMed Central

Boulanger, Yan; Cyr, Dominic; Taylor, Anthony R.; Price, David T.; St-Laurent, Martin-Hugues

2018-01-01

Many studies project future bird ranges by relying on correlative species distribution models. Such models do not usually represent important processes explicitly related to climate change and harvesting, which limits their potential for predicting and understanding the future of boreal bird assemblages at the landscape scale. In this study, we attempted to assess the cumulative and specific impacts of both harvesting and climate-induced changes on wildfires and stand-level processes (e.g., reproduction, growth) in the boreal forest of eastern Canada. The projected changes in these landscape- and stand-scale processes (referred to as “drivers of change”) were then assessed for their impacts on future habitats and potential productivity of black-backed woodpecker (BBWO; Picoides arcticus), a focal species representative of deadwood and old-growth biodiversity in eastern Canada. Forest attributes were simulated using a forest landscape model, LANDIS-II, and were used to infer future landscape suitability to BBWO under three anthropogenic climate forcing scenarios (RCP 2.6, RCP 4.5 and RCP 8.5), compared to the historical baseline. We found climate change is likely to be detrimental for BBWO, with up to 92% decline in potential productivity under the worst-case climate forcing scenario (RCP 8.5). However, large declines were also projected under baseline climate, underlining the importance of harvest in determining future BBWO productivity. Present-day harvesting practices were the single most important cause of declining areas of old-growth coniferous forest, and hence appeared as the single most important driver of future BBWO productivity, regardless of the climate scenario. Climate-induced increases in fire activity would further promote young, deciduous stands at the expense of old-growth coniferous stands. This suggests that the biodiversity associated with deadwood and old-growth boreal forests may be greatly altered by the cumulative impacts of natural and anthropogenic disturbances under a changing climate. Management adaptations, including reduced harvesting levels and strategies to promote coniferous species content, may help mitigate these cumulative impacts. PMID:29414989

Harvesting interacts with climate change to affect future habitat quality of a focal species in eastern Canada's boreal forest.

PubMed

Tremblay, Junior A; Boulanger, Yan; Cyr, Dominic; Taylor, Anthony R; Price, David T; St-Laurent, Martin-Hugues

2018-01-01

Many studies project future bird ranges by relying on correlative species distribution models. Such models do not usually represent important processes explicitly related to climate change and harvesting, which limits their potential for predicting and understanding the future of boreal bird assemblages at the landscape scale. In this study, we attempted to assess the cumulative and specific impacts of both harvesting and climate-induced changes on wildfires and stand-level processes (e.g., reproduction, growth) in the boreal forest of eastern Canada. The projected changes in these landscape- and stand-scale processes (referred to as "drivers of change") were then assessed for their impacts on future habitats and potential productivity of black-backed woodpecker (BBWO; Picoides arcticus), a focal species representative of deadwood and old-growth biodiversity in eastern Canada. Forest attributes were simulated using a forest landscape model, LANDIS-II, and were used to infer future landscape suitability to BBWO under three anthropogenic climate forcing scenarios (RCP 2.6, RCP 4.5 and RCP 8.5), compared to the historical baseline. We found climate change is likely to be detrimental for BBWO, with up to 92% decline in potential productivity under the worst-case climate forcing scenario (RCP 8.5). However, large declines were also projected under baseline climate, underlining the importance of harvest in determining future BBWO productivity. Present-day harvesting practices were the single most important cause of declining areas of old-growth coniferous forest, and hence appeared as the single most important driver of future BBWO productivity, regardless of the climate scenario. Climate-induced increases in fire activity would further promote young, deciduous stands at the expense of old-growth coniferous stands. This suggests that the biodiversity associated with deadwood and old-growth boreal forests may be greatly altered by the cumulative impacts of natural and anthropogenic disturbances under a changing climate. Management adaptations, including reduced harvesting levels and strategies to promote coniferous species content, may help mitigate these cumulative impacts.

Far-field Wireless Energy Harvesting for Increased Safeguards Equipment Battery Life.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hymel, Ross W.

Modern unattended safeguards equipment (e.g. seals) incorporates many low-power electronic circuits, which are typically powered by expensive and toxic lithium thionyl chloride (LiSOCL2) batteries. The limited life of these batteries necessitates their periodic replacement. This replacement must be performed before total battery discharge to avoid potential loss of continuity of knowledge. Thus, the effective battery capacity becomes significantly less than the actual usable capacity. Additionally, such maintenance is a radiological hazard to personnel, as well as a monetary burden to a safeguards inspectorate. Energy harvesting, a commercially available technology, could extend the operational life of batterypowered equipment to achieve significantmore » efficiencies for safeguards deployments. Energy harvesting is the scavenging and storage of ambient energy sources, such as solar, thermal, and kinetic for use in lowpower electronic applications. While the amount of scavenged energy per unit time may be small, it most often comes from a source that will not be depleted throughout the deployment of the harvesting device. The best-known energy harvesters are solar panels and wind turbines. Recently, far-field wireless energy harvesting has become a commercially available option. Far-field wireless energy harvesting provides consistent, predictable, and un-tethered power over distances up to 50 feet. This process converts radio frequency (RF) energy, both intentionally emitted and ambient, into usable direct current (DC) power. Incorporating far-field wireless energy harvesting into safeguards equipment can significantly extend the equipment’s battery life and perhaps make it indefinite. Furthermore, additional functionality can be added to safeguards equipment without lowering its operational life expectancy. This paper explores the benefits and drawbacks of integrating far-field wireless energy harvesting into a chosen safeguards seal: the Remotely Monitored Sealing Array (RMSA). Specifically, it examines the performance of a commercially available RF harvesting system from Powercast, as well as commercial and custom antenna solutions.« less

Stretchable piezoelectric nanocomposite generator

NASA Astrophysics Data System (ADS)

Park, Kwi-Il; Jeong, Chang Kyu; Kim, Na Kyung; Lee, Keon Jae

2016-06-01

Piezoelectric energy conversion that generate electric energy from ambient mechanical and vibrational movements is promising energy harvesting technology because it can use more accessible energy resources than other renewable natural energy. In particular, flexible and stretchable piezoelectric energy harvesters which can harvest the tiny biomechanical motions inside human body into electricity properly facilitate not only the self-powered energy system for flexible and wearable electronics but also sensitive piezoelectric sensors for motion detectors and in vivo diagnosis kits. Since the piezoelectric ZnO nanowires (NWs)-based energy harvesters (nanogenerators) were proposed in 2006, many researchers have attempted the nanogenerator by using the various fabrication process such as nanowire growth, electrospinning, and transfer techniques with piezoelectric materials including polyvinylidene fluoride (PVDF) polymer and perovskite ceramics. In 2012, the composite-based nanogenerators were developed using simple, low-cost, and scalable methods to overcome the significant issues with previously-reported energy harvester, such as insufficient output performance and size limitation. This review paper provides a brief overview of flexible and stretchable piezoelectric nanocomposite generator for realizing the self-powered energy system with development history, power performance, and applications.

MEMS-based wide-bandwidth electromagnetic energy harvester with electroplated nickel structure

NASA Astrophysics Data System (ADS)

Sun, Shi; Dai, Xuhan; Sun, Yunna; Xiang, Xiaojian; Ding, Guifu; Zhao, Xiaolin

2017-11-01

A novel nickel-based nonlinear electromagnetic energy harvester has been designed, fabricated, and characterized in this work. Electroplated nickel is very suitable for a stretching-based mechanism to broaden the bandwidth due to its good process and mechanical properties. A strong hardening nonlinearity is induced due to the large deformation of the thin nickel based guided-beam structure. Combining the merits of both the mechanical properties and guided-beam structure, the energy harvester shows good bandwidth performance. It is found that increasing the thickness of the central platform could guarantee nonlinearity. Static and dynamic models of the energy harvester are simulated and validated. Test results show that the energy harvester has good repeatability without any destruction under a large deformation condition. At the acceleration of 0.5 g, comparative large bandwidths of 129 and 59 Hz are obtained for displacement and RMS output voltage, respectively. Power output of 3.4 µW and normalized power density of 125.92 µW cm-3 g-2 are achieved with the load resistance of 38 Ω.

Piezoelectric energy harvester under parquet floor

NASA Astrophysics Data System (ADS)

Bischur, E.; Schwesinger, N.

2011-03-01

The design, fabrication and testing of piezoelectric energy harvesting modules for floors is described. These modules are used beneath a parquet floor to harvest the energy of people walking over it. The harvesting modules consist of monoaxial stretched PVDF-foils. Multilayer modules are built up as roller-type capacitors. The fabrication process of the harvesting modules is simple and very suitable for mass production. Due to the use of organic polymers, the modules are characterized by a great flexibility and the possibility to create them in almost any geometrical size. The energy yield was determined depending on the dynamic loading force, the thickness of piezoelectric active material, the size of the piezoelectric modules, their alignment in the walking direction and their position on the floor. An increase of the energy yield at higher loading forces and higher thicknesses of the modules was observed. It was possible to generate up to 2.1mWs of electric energy with dynamic loads of 70kg using a specific module design. Furthermore a test floor was assembled to determine the influence of the size, alignment and position of the modules on the energy yield.

Applications of energy harvesting for ultralow power technology

NASA Astrophysics Data System (ADS)

Pop-Vadean, A.; Pop, P. P.; Barz, C.; Chiver, O.

2015-06-01

Ultra-low-power (ULP) technology is enabling a wide range of new applications that harvest ambient energy in very small amounts and need little or no maintenance - self-sustaining devices that are capable of perpetual or nearly perpetual operation. These new systems, which are now appearing in industrial and consumer electronics, also promise great changes in medicine and health. Until recently, the idea of micro-scale energy harvesting, and collecting miniscule amounts of ambient energy to power electronic systems, was still limited to research proposals and laboratory experiments.Today an increasing number of systems are appearing that take advantage of light, vibrations and other forms of previously wasted environmental energy for applications where providing line power or maintaining batteries is inconvenient. In the industrial world, where sensors gather information from remote equipment and hazardous processes; in consumer electronics, where mobility and convenience are served; and in medical systems, with unique requirements for prosthetics and non-invasive monitoring, energy harvesting is rapidly expanding into new applications.This paper serves as a survey for applications of energy harvesting for ultra low power technology based on various technical papers available in the public domain.

Wind energy harvesting using a piezo-composite generating element (PCGE)

NASA Astrophysics Data System (ADS)

Tien, Cam Minh Tri; Goo, Nam-Seo

2010-04-01

Energy can be reclaimed and stored for later use to recharge a battery or power a device through a process called energy harvesting. Piezoelectric is being widely investigated for use in harvesting surrounding energy sources such as sun, wind, tides, indoor lighting, body movement or machine vibration, etc. This paper introduces a wind energy harvesting device using a Piezo-Composite Generating Element (PCGE). The PCGE is composed of layers of carbon/epoxy, PZT ceramic, and glass/epoxy cured at an elevated temperature. In the prototype, The PCGE performs as a secondary beam element. One end of the PCGE is attached on the frame of the device. The fan blade rotates in the direction of the wind and hits the PCGE's tip. When the PCGE is excited, the effects of the beam deformation allow it to generate electric power. In wind tunnel experiments, the PCGE is excited to vibrate at its first natural frequency and generates the power up to 8.5 mW. The prototype can harvest energy in urban regions with minor wind movement.

Vibration energy harvesting based on stress-induced polarization switching: a phase field approach

NASA Astrophysics Data System (ADS)

Wang, Dan; Wang, Linxiang; Melnik, Roderick

2017-06-01

Different from the traditional piezoelectric vibration energy harvesting, a new strategy based on stress-induced polarization switching has been proposed in the current paper. Two related prototypes are presented and the associated advantages and drawbacks have been discussed in detail. It has been demonstrated that, with the assistance of a bias electric field, the robustness of the energy harvesters is improved. Furthermore, the real-space phase-field model has been employed to study the nonlinear hysteretic behavior involved in the proposed energy harvesting process. A substantially larger electric current associated with the stress-induced polarization switching has been demonstrated when compared with that with piezoelectric effect. In addition, the effects of bias electric potential, bias resistance, mechanical boundary conditions, charge leakage and electrodes arrangements have also been investigated by the phase-field simulation, which provides a guidance for future real implementations.

Modeling of capacitor charging dynamics in an energy harvesting system considering accurate electromechanical coupling effects

NASA Astrophysics Data System (ADS)

Bagheri, Shahriar; Wu, Nan; Filizadeh, Shaahin

2018-06-01

This paper presents an iterative numerical method that accurately models an energy harvesting system charging a capacitor with piezoelectric patches. The constitutive relations of piezoelectric materials connected with an external charging circuit with a diode bridge and capacitors lead to the electromechanical coupling effect and the difficulty of deriving accurate transient mechanical response, as well as the charging progress. The proposed model is built upon the Euler-Bernoulli beam theory and takes into account the electromechanical coupling effects as well as the dynamic process of charging an external storage capacitor. The model is validated through experimental tests on a cantilever beam coated with piezoelectric patches. Several parametric studies are performed and the functionality of the model is verified. The efficiency of power harvesting system can be predicted and tuned considering variations in different design parameters. Such a model can be utilized to design robust and optimal energy harvesting system.

Method and apparatus for monitoring characteristics of a flow path having solid components flowing therethrough

DOEpatents

Hoskinson, Reed L [Rigby, ID; Svoboda, John M [Idaho Falls, ID; Bauer, William F [Idaho Falls, ID; Elias, Gracy [Idaho Falls, ID

2008-05-06

A method and apparatus is provided for monitoring a flow path having plurality of different solid components flowing therethrough. For example, in the harvesting of a plant material, many factors surrounding the threshing, separating or cleaning of the plant material and may lead to the inadvertent inclusion of the component being selectively harvested with residual plant materials being discharged or otherwise processed. In accordance with the present invention the detection of the selectively harvested component within residual materials may include the monitoring of a flow path of such residual materials by, for example, directing an excitation signal toward of flow path of material and then detecting a signal initiated by the presence of the selectively harvested component responsive to the excitation signal. The detected signal may be used to determine the presence or absence of a selected plant component within the flow path of residual materials.

Harvesting and contamination control of microalgae Chlorella ellipsoidea using the bio-polymeric flocculant α-poly-l-lysine.

PubMed

Noh, Won; Kim, Jungmin; Lee, Sang-Jun; Ryu, Byung-Gon; Kang, Chang-Min

2018-02-01

Microalgae have been extensively studied for the production of various products. However, to date, microalgal biomass has not become economically feasible, mainly due to different issues such as contamination from various sources that occurs during downstream processes, and which leads to low quality biomass with limited application. In this study, to overcome contamination by flocculants and other microorganisms, the cationic biopolymer α-Poly-l-lysine (α-PLL) was applied. The cationic amine moiety and polymeric chain of α-PLL rendered microalgal harvesting efficient. With increasing α-PLL chain length, efficient dose- and time-dependent harvesting was achieved. In addition to efficient flocculation performance, biomass harvested using α-PLL showed suppressed biological contamination through the inherent antimicrobial activity of α-PLL. Thus, it is possible to upgrade the quality and storability of produced microalgal biomass using α-PLL-induced flocculation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Optical arc sensor using energy harvesting power source

DOE Office of Scientific and Technical Information (OSTI.GOV)

Choi, Kyoo Nam, E-mail: knchoi@inu.ac.kr; Rho, Hee Hyuk, E-mail: rdoubleh0902@inu.ac.kr

Wireless sensors without external power supply gained considerable attention due to convenience both in installation and operation. Optical arc detecting sensor equipping with self sustaining power supply using energy harvesting method was investigated. Continuous energy harvesting method was attempted using thermoelectric generator to supply standby power in micro ampere scale and operating power in mA scale. Peltier module with heat-sink was used for high efficiency electricity generator. Optical arc detecting sensor with hybrid filter showed insensitivity to fluorescent and incandescent lamps under simulated distribution panel condition. Signal processing using integrating function showed selective arc discharge detection capability to different arcmore » energy levels, with a resolution below 17 J energy difference, unaffected by bursting arc waveform. The sensor showed possibility for application to arc discharge detecting sensor in power distribution panel. Also experiment with proposed continuous energy harvesting method using thermoelectric power showed possibility as a self sustainable power source of remote sensor.« less

Replication of Leaf Surface Structures for Light Harvesting

PubMed Central

Huang, Zhongjia; Yang, Sai; Zhang, Hui; Zhang, Meng; Cao, Wei

2015-01-01

As one of the most important hosts of natural light harvesting, foliage normally has complicated surface structures to capture solar radiances. Bio-mimicking leaf surface structures can provide novel designs of covers in photovoltaic systems. In this article, we reported on replicating leaf surface structures on poly-(methyl methacrylate) polymers to prompt harvesting efficiencies. Prepared via a double transfer process, the polymers were found to have high optical transparencies and transmission hazes, with both values exceeding 80% in some species. Benefiting from optical properties and wrinkled surfaces, the biomimetic polymers brought up to 17% gains to photovoltaic efficiencies. Through Monte-Carlo simulations of light transport, ultrahigh haze values and low reflections were attributed to lightwave guidance schemes lead by the nano- and micro-morphologies which are inherited from master leaves. Thus, leaf surface bio-mimicking can be considered as a strategic direction to design covers of light harvesting systems. PMID:26381702

Optical arc sensor using energy harvesting power source

NASA Astrophysics Data System (ADS)

Choi, Kyoo Nam; Rho, Hee Hyuk

2016-06-01

Wireless sensors without external power supply gained considerable attention due to convenience both in installation and operation. Optical arc detecting sensor equipping with self sustaining power supply using energy harvesting method was investigated. Continuous energy harvesting method was attempted using thermoelectric generator to supply standby power in micro ampere scale and operating power in mA scale. Peltier module with heat-sink was used for high efficiency electricity generator. Optical arc detecting sensor with hybrid filter showed insensitivity to fluorescent and incandescent lamps under simulated distribution panel condition. Signal processing using integrating function showed selective arc discharge detection capability to different arc energy levels, with a resolution below 17J energy difference, unaffected by bursting arc waveform. The sensor showed possibility for application to arc discharge detecting sensor in power distribution panel. Also experiment with proposed continuous energy harvesting method using thermoelectric power showed possibility as a self sustainable power source of remote sensor.

Selecting, Establishing, and Managing Switchgrass (Panicum virgatum) for Biofuels

NASA Astrophysics Data System (ADS)

Parrish, David J.; Fike, John H.

Switchgrass is being widely considered as a feedstock for biofuel production. Much remains to be learned about ideal feedstock characteristics, but switchgrass offers many advantages already and can perhaps be manipulated to offer more. When planning to grow switchgrass, select a cultivar that is well adapted to the location - generally a lowland cultivar for the southern United States and an upland cultivar at higher latitudes. Plant non-dormant seed after soils are well warmed, preferably with no-till methods and always with good weed control. Except for weeds, few pests appear to be widespread; but disease and insect pests could become more important as acreages increase. Fertilization requirements are relatively low, with 50 kg N/ha/year being a good “generic” recommendation where a single harvest is taken after plants have senesced; more will be needed if biomass is harvested while still green. Switchgrass should be harvested no more than twice per year and may generally be expected to produce 12 to ≥20 mg/ha/year across its usual range of distribution. A single harvest may provide for maximum sustainable yields - especially if the harvest is taken after tops die back at the end of the season. Several harvesting technologies are available, but the preferred technology may depend on logistics and economics associated with the local processing point, or biorefinery.

Powering autonomous sensors with miniaturized piezoelectric based energy harvesting devices operating at very low frequency

NASA Astrophysics Data System (ADS)

Ferin, G.; Bantignies, C.; Le Khanh, H.; Flesch, E.; Nguyen-Dinh, A.

2015-12-01

Harvesting energy from ambient mechanical vibrations is a smart and efficient way to power autonomous sensors and support innovative developments in IoT (Internet of Things), WSN (Wireless Sensor Network) and even implantable medical devices. Beyond the environmental operating conditions, efficiency of such devices is mainly related to energy source properties like the amplitude of vibrations and its spectral contain and some of these applications exhibit a quite low frequency spectrum where harvesting surrounding mechanical energy make sense, typically 5-50Hz for implantable medical devices or 50Hz-150Hz for industrial machines. Harvesting such low frequency vibrations is a challenge since it leads to adapt the resonator geometries to the targeted frequency or to use out-off band indirect harvesting strategies. In this paper we present a piezoelectric based vibrational energy harvesting device (PEH) which could be integrated into a biocompatible package to power implantable sensor or therapeutic medical devices. The presented architecture is a serial bimorph laminated with ultra-thinned (ranging from 15μm to 100μm) outer PZT “skins” that could operate at a “very low frequency”, below 25Hz typically. The core process flow is disclosed and performances highlighted with regards to other low frequency demonstrations.

Selecting, establishing, and managing switchgrass (Panicum virgatum) for biofuels.

PubMed

Parrish, David J; Fike, John H

2009-01-01

Switchgrass is being widely considered as a feedstock for biofuel production. Much remains to be learned about ideal feedstock characteristics, but switchgrass offers many advantages already and can perhaps be manipulated to offer more. When planning to grow switchgrass, select a cultivar that is well adapted to the location - generally a lowland cultivar for the southern United States and an upland cultivar at higher latitudes. Plant non-dormant seed after soils are well warmed, preferably with no-till methods and always with good weed control. Except for weeds, few pests appear to be widespread; but disease and insect pests could become more important as acreages increase. Fertilization requirements are relatively low, with 50 kg N/ha/year being a good "generic" recommendation where a single harvest is taken after plants have senesced; more will be needed if biomass is harvested while still green. Switchgrass should be harvested no more than twice per year and may generally be expected to produce 12 to >or=20 mg/ha/year across its usual range of distribution. A single harvest may provide for maximum sustainable yields - especially if the harvest is taken after tops die back at the end of the season. Several harvesting technologies are available, but the preferred technology may depend on logistics and economics associated with the local processing point, or biorefinery.

Land management: data availability and process understanding for global change studies.

PubMed

Erb, Karl-Heinz; Luyssaert, Sebastiaan; Meyfroidt, Patrick; Pongratz, Julia; Don, Axel; Kloster, Silvia; Kuemmerle, Tobias; Fetzel, Tamara; Fuchs, Richard; Herold, Martin; Haberl, Helmut; Jones, Chris D; Marín-Spiotta, Erika; McCallum, Ian; Robertson, Eddy; Seufert, Verena; Fritz, Steffen; Valade, Aude; Wiltshire, Andrew; Dolman, Albertus J

2017-02-01

In the light of daunting global sustainability challenges such as climate change, biodiversity loss and food security, improving our understanding of the complex dynamics of the Earth system is crucial. However, large knowledge gaps related to the effects of land management persist, in particular those human-induced changes in terrestrial ecosystems that do not result in land-cover conversions. Here, we review the current state of knowledge of ten common land management activities for their biogeochemical and biophysical impacts, the level of process understanding and data availability. Our review shows that ca. one-tenth of the ice-free land surface is under intense human management, half under medium and one-fifth under extensive management. Based on our review, we cluster these ten management activities into three groups: (i) management activities for which data sets are available, and for which a good knowledge base exists (cropland harvest and irrigation); (ii) management activities for which sufficient knowledge on biogeochemical and biophysical effects exists but robust global data sets are lacking (forest harvest, tree species selection, grazing and mowing harvest, N fertilization); and (iii) land management practices with severe data gaps concomitant with an unsatisfactory level of process understanding (crop species selection, artificial wetland drainage, tillage and fire management and crop residue management, an element of crop harvest). Although we identify multiple impediments to progress, we conclude that the current status of process understanding and data availability is sufficient to advance with incorporating management in, for example, Earth system or dynamic vegetation models in order to provide a systematic assessment of their role in the Earth system. This review contributes to a strategic prioritization of research efforts across multiple disciplines, including land system research, ecological research and Earth system modelling. © 2016 John Wiley & Sons Ltd.

Effects of antibody disulfide bond reduction on purification process performance and final drug substance stability

PubMed Central

Russell, Brian; Yang, Yanhong; Handlogten, Michael; Hudak, Suzanne; Cao, Mingyan; Wang, Jihong; Robbins, David; Ahuja, Sanjeev; Zhu, Min

2017-01-01

ABSTRACT Antibody disulfide bond reduction during monoclonal antibody (mAb) production is a phenomenon that has been attributed to the reducing enzymes from CHO cells acting on the mAb during the harvest process. However, the impact of antibody reduction on the downstream purification process has not been studied. During the production of an IgG2 mAb, antibody reduction was observed in the harvested cell culture fluid (HCCF), resulting in high fragment levels. In addition, aggregate levels increased during the low pH treatment step in the purification process. A correlation between the level of free thiol in the HCCF (as a result of antibody reduction) and aggregation during the low pH step was established, wherein higher levels of free thiol in the starting sample resulted in increased levels of aggregates during low pH treatment. The elevated levels of free thiol were not reduced over the course of purification, resulting in carry‐over of high free thiol content into the formulated drug substance. When the drug substance with high free thiols was monitored for product degradation at room temperature and 2–8°C, faster rates of aggregation were observed compared to the drug substance generated from HCCF that was purified immediately after harvest. Further, when antibody reduction mitigations (e.g., chilling, aeration, and addition of cystine) were applied, HCCF could be held for an extended period of time while providing the same product quality/stability as material that had been purified immediately after harvest. Biotechnol. Bioeng. 2017;114: 1264–1274. © 2017 The Authors. Biotechnology and Bioengineering Published by Wiley Periodicals Inc. PMID:28186329

The content of polyphenolic compounds in cocoa beans (Theobroma cacao L.), depending on variety, growing region, and processing operations: a review.

PubMed

Oracz, Joanna; Zyzelewicz, Dorota; Nebesny, Ewa

2015-01-01

Polyphenols form the largest group of compounds among natural antioxidants, which largely affect the overall antioxidant and anti-free radical activity of cocoa beans. The qualitative and quantitative composition of individual fractions of polyphenolic compounds, even within one species, is very diverse and depends on many factors, mainly on the area of cocoa trees cultivation, bean maturity, climatic conditions during growth, and the harvest season and storage time after harvest. Thermal processing of cocoa beans and cocoa derivative products at relatively high temperatures may in addition to favorable physicochemical, microbiological, and organoleptic changes result in a decrease of polyphenols concentration. Technological processing of cocoa beans negatively affects the content of polyphenolic compounds.

Short-term changes in soil C, N, and biota following harvesting and regeneration of loblolly pine (Pinus taeda L.)

Treesearch

Mason C. Carter; Thomas J. Dean; Minyi Zhou; Michael G. Messina; Ziyin Wang

2002-01-01

In affiliation with the USDA-FS long-term soil productivity program, a series of studies have been established in the US gulf coast region to monitor the effects of intensive silviculture on site productivity. This report presents early results of a study of the interactive effects of harvest intensity and cultural treatments on soil C, N, and biological processes...

Whole-tree and forest floor removal from a loblolly pine plantation have no effect on forest floor CO2 efflux 10 years after harvest

Treesearch

John R. Butnor; Kurt H. Johnsen; Felipe G. Sanchez

2006-01-01

Intensive management of southern pine plantations has yielded multifold increases in productivity over the last half century. The process of harvesting merchantable material and preparing a site for planting can lead to a considerable loss of organic matter. Intensively managed stands may experience more frequent disturbance as rotations decrease in length, exposing...

Energy harvesting from human motion: materials and techniques.

PubMed

Invernizzi, F; Dulio, S; Patrini, M; Guizzetti, G; Mustarelli, P

2016-10-10

Energy harvesting from human motion is a research field under rapid development. In this tutorial review we address the main physical and physico-chemical processes which can lead to energy generation, including electromagnetism, piezoelectricity, and electrostatic generation. Emphasis is put on the relationships among material properties and device efficiency. Some new and relatively less known approaches, such as triboelectric nanogeneration (TENG) and reverse electrowetting (REWOD), are reported in more detail.

Environmental Impact Analysis Process Environmental Assessment PEGASUS Air Launched Space Booster

DTIC Science & Technology

1989-09-01

central and southern California. The broad-leaved forest formation, consisting of the mixed hardwood, southern oak, and the blue oak-digger pine...species of mollusks, such as abalones, cams, and squid, are harvested commercially. Octopus is sometimes taken for food. The crustacean harvest in...borealis Sei whale En, T B. musculus Blue whale En, T B. physalus Finback whale En, T Eubalaena sieboldii Right whale En, T

A Twice Electrochemical-Etching Method to Fabricate Superhydrophobic-Superhydrophilic Patterns for Biomimetic Fog Harvest.

PubMed

Yang, Xiaolong; Song, Jinlong; Liu, Junkai; Liu, Xin; Jin, Zhuji

2017-08-18

Superhydrophobic-superhydrophilic patterned surfaces have attracted more and more attention due to their great potential applications in the fog harvest process. In this work, we developed a simple and universal electrochemical-etching method to fabricate the superhydrophobic-superhydrophilic patterned surface on metal superhydrophobic substrates. The anti-electrochemical corrosion property of superhydrophobic substrates and the dependence of electrochemical etching potential on the wettability of the fabricated dimples were investigated on Al samples. Results showed that high etching potential was beneficial for efficiently producing a uniform superhydrophilic dimple. Fabrication of long-term superhydrophilic dimples on the Al superhydrophobic substrate was achieved by combining the masked electrochemical etching and boiling-water immersion methods. A long-term wedge-shaped superhydrophilic dimple array was fabricated on a superhydrophobic surface. The fog harvest test showed that the surface with a wedge-shaped pattern array had high water collection efficiency. Condensing water on the pattern was easy to converge and depart due to the internal Laplace pressure gradient of the liquid and the contact angle hysteresis contrast on the surface. The Furmidge equation was applied to explain the droplet departing mechanism and to control the departing volume. The fabrication technique and research of the fog harvest process may guide the design of new water collection devices.

Hydrologic resilience of a Canadian Foothills watershed to forest harvest

NASA Astrophysics Data System (ADS)

Goodbrand, Amy; Anderson, Axel

2016-04-01

Recent investigations of long-term hydrometeorological, groundwater, and streamflow data from watersheds on the eastern slopes of the Canadian Rocky Mountains showed the streamflow regime was resilient to forest harvest. These watersheds had low levels of harvest relative to their size and a large area of sparsely vegetated alpine talus slopes and exposed bedrock; an area shown to generate the majority of runoff for streamflow. In contrast, watersheds located in the foothills of the Rocky Mountains are of lower relief and typically have harvestable timber throughout the watershed; therefore, these watersheds may be more sensitive to forest disturbance and have increased potential for streamflow response. This project assesses the hydrologic resilience of an Alberta Foothills watershed to forest harvest using a 23-year dataset from the Tri-Creeks Experimental Watershed (Tri-Creeks). Tri-Creeks has been the site of intensive streamflow, groundwater, snow accumulation, and precipitation observations from 1967 - 1990. During the early 1980s, forestry experiments were conducted to compare the effects of timber harvest and riparian buffers, and the effectiveness of timber harvesting ground rules in protecting fisheries and maintaining water resources within three sub-watersheds: Eunice (16.8 km2; control); Deerlick (15.2 km2; 36% streamside timber removal); and, Wampus (28.3 km2; 37% clear-cut). Statistical analyses were used to compare the pre-and post-harvest ratios of treatment to control sub-watershed runoff for: water year, monthly (April - October), snowmelt peak flow, and low flow (10th percentile streamflow) periods as an assessment of hydrologic resilience to forest harvest. The only significant post-harvest change was an increase in water yield during May at Wampus (Mann-Whitney (MW), p<0.05) and Deerlick (MW, p<0.1) Creeks. The lack of change in snowmelt peak flow timing or magnitude was not expected, particularly in Deerlick, which had 36% streamside timber removal. The streamflow regime of Tri-Creeks displayed remarkable resilience to forest harvest. We hypothesize on the processes and characteristics that result in this watershed to exhibit greater resilience compared to other forested watersheds.

Addressing wild turkey population declines using structured decision making

USGS Publications Warehouse

Robinson, Kelly F.; Fuller, Angela K.; Schiavone, Michael V.; Swift, Bryan L.; Diefenbach, Duane R.; Siemer, William F.; Decker, Daniel J.

2017-01-01

We present a case study from New York, USA, of the use of structured decision making (SDM) to identify fall turkey harvest regulations that best meet stakeholder objectives, in light of recent apparent declines in abundance of wild turkeys in the northeastern United States. We used the SDM framework to incorporate the multiple objectives associated with turkey hunting, stakeholder desires, and region-specific ecological and environmental factors that could influence fall harvest. We identified a set of 4 fall harvest regulations, composed of different season lengths and bag limits, and evaluated their relative achievement of the objectives. We used a stochastic turkey population model, statistical modeling, and expert elicitation to evaluate the consequences of each harvest regulation on each of the objectives. We conducted a statewide mail survey of fall turkey hunters in New York to gather the necessary information to evaluate tradeoffs among multiple objectives associated with hunter satisfaction. The optimal fall harvest regulation was a 2-week season and allowed for the harvest of 1 bird/hunter. This regulation was the most conservative of those evaluated, reflecting the concerns about recent declines in turkey abundance among agency wildlife biologists and the hunting public. Depending on the region of the state, the 2-week, 1-bird regulation was predicted to result in 7–32% more turkeys on the landscape after 5 years. The SDM process provided a transparent framework for setting fall turkey harvest regulations and reduced potential stakeholder conflict by explicitly taking the multiple objectives of different stakeholder groups into account.

Characterization of real-world vibration sources with a view toward optimal energy harvesting architectures

NASA Astrophysics Data System (ADS)

Rantz, Robert; Roundy, Shad

2016-04-01

A tremendous amount of research has been performed on the design and analysis of vibration energy harvester architectures with the goal of optimizing power output; most studies assume idealized input vibrations without paying much attention to whether such idealizations are broadly representative of real sources. These "idealized input signals" are typically derived from the expected nature of the vibrations produced from a given source. Little work has been done on corroborating these expectations by virtue of compiling a comprehensive list of vibration signals organized by detailed classifications. Vibration data representing 333 signals were collected from the NiPS Laboratory "Real Vibration" database, processed, and categorized according to the source of the signal (e.g. animal, machine, etc.), the number of dominant frequencies, the nature of the dominant frequencies (e.g. stationary, band-limited noise, etc.), and other metrics. By categorizing signals in this way, the set of idealized vibration inputs commonly assumed for harvester input can be corroborated and refined, and heretofore overlooked vibration input types have motivation for investigation. An initial qualitative analysis of vibration signals has been undertaken with the goal of determining how often a standard linear oscillator based harvester is likely the optimal architecture, and how often a nonlinear harvester with a cubic stiffness function might provide improvement. Although preliminary, the analysis indicates that in at least 23% of cases, a linear harvester is likely optimal and in no more than 53% of cases would a nonlinear cubic stiffness based harvester provide improvement.

Energy harvesting from mastication forces via a smart tooth

NASA Astrophysics Data System (ADS)

Bani-Hani, Muath; Karami, M. Amin

2016-04-01

The batteries of the current pacing devices are relatively large and occupy over 60 percent of the size of pulse generators. Therefore, they cannot be placed in the subtle areas of human body. In this paper, the mastication force and the resulting tooth pressure are converted to electricity. The pressure energy can be converted to electricity by using the piezoelectric effect. The tooth crown is used as a power autonomous pulse generator. We refer to this envisioned pulse generator as the smart tooth. The smart tooth is in the form of a dental implant. A piezoelectric vibration energy harvester is designed and modeled for this purpose. The Piezoelectric based energy harvesters investigated and analyzed in this paper initially includes a single degree of freedom piezoelectric based stack energy harvester which utilizes a harvesting circuit employing the case of a purely resistive circuit. The next step is utilizing and investigating a bimorph piezoelectric beam which is integrated/embedded in the smart tooth implant. Mastication process causes the bimorph beam to buckle or return to unbuckled condition. The transitions results in vibration of the piezoelectric beam and thus generate energy. The power estimated by the two mechanisms is in the order of hundreds of microwatts. Both scenarios of the energy harvesters are analytically modeled. The exact analytical solution of the piezoelectric beam energy harvester with Euler-Bernoulli beam assumptions is presented. The electro-mechanical coupling and the geometric nonlinearities have been included in the model for the piezoelectric beam.

Monitoring agricultural processing electrical energy use and efficiency

USDA-ARS?s Scientific Manuscript database

Energy costs have become proportionately larger as cotton post-harvest processing facilities have utilized other inputs more efficiently. A discrepancy in energy consumption per unit processed between facilities suggests that energy could be utilized more efficiently. Cotton gin facilities were in...

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

John "JC" Carver, a payload integration engineer with NASA Kennedy Space Center's Test and Operations Support Contract, harvests half the Arabidopsis thaliana plants inside the growth chamber of the Advanced Plant Habitat (APH) Flight Unit No. 1. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in Kennedy's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Thermoelectric as recovery and harvesting of waste heat from portable generator

NASA Astrophysics Data System (ADS)

Mustafa, S. N.; Kamarrudin, N. S.; Hashim, M. S. M.; Bakar, S. A.; Razlan, Z. M.; Harun, A.; Ibrahim, I.; Faizi, M. K.; Saad, M. A. M.; Zunaidi, I.; Wan, W. K.; Desa, H.

2017-10-01

Generation of waste heat was ineluctable especially during energy producing process. Waste heat falls into low temperature grade make it complicated to utilize. Thermoelectric generator (TEG) offers opportunity to harvest any temperature grade heat into useful electricity. This project is covered about recovery and utilizing waste heat from portable electric generator by using a TEG which placed at exhaust surface. Temperature difference at both surfaces of TEG was enhanced with supplying cold air from a wind blower. It is found that, even at low air speed, the TEG was successfully produced electricity with aid from DC-DC booster. Results shows possibility to harvest low temperature grade heat and still exist areas for continual improvement.

A Design Study Of A Wireless Power Transfer System For Use To Transfer Energy From A Vibration Energy Harvester

NASA Astrophysics Data System (ADS)

Grabham, N. J.; Harden, C.; Vincent, D.; Beeby, S. P.

2016-11-01

A wirelessly powered remote sensor node is presented along with its design process. The purpose of the node is the further expansion of the sensing capabilities of the commercial Perpetuum system used for condition monitoring on trains and rolling stock which operates using vibration energy harvesting. Surplus harvested vibration energy is transferred wirelessly to a remote satellite sensor to allow measurements over a wider area to be made. This additional data is to be used for long term condition monitoring. Performance measurements made on the prototype remote sensor node are reported and advantages and disadvantages of using the same RF frequency for power and data transfer are identified.

Improving power output of inertial energy harvesters by employing principal component analysis of input acceleration

NASA Astrophysics Data System (ADS)

Smilek, Jan; Hadas, Zdenek

2017-02-01

In this paper we propose the use of principal component analysis to process the measured acceleration data in order to determine the direction of acceleration with the highest variance on given frequency of interest. This method can be used for improving the power generated by inertial energy harvesters. Their power output is highly dependent on the excitation acceleration magnitude and frequency, but the axes of acceleration measurements might not always be perfectly aligned with the directions of movement, and therefore the generated power output might be severely underestimated in simulations, possibly leading to false conclusions about the feasibility of using the inertial energy harvester for the examined application.

Evaluation of reinitialization-free nonvolatile computer systems for energy-harvesting Internet of things applications

NASA Astrophysics Data System (ADS)

Onizawa, Naoya; Tamakoshi, Akira; Hanyu, Takahiro

2017-08-01

In this paper, reinitialization-free nonvolatile computer systems are designed and evaluated for energy-harvesting Internet of things (IoT) applications. In energy-harvesting applications, as power supplies generated from renewable power sources cause frequent power failures, data processed need to be backed up when power failures occur. Unless data are safely backed up before power supplies diminish, reinitialization processes are required when power supplies are recovered, which results in low energy efficiencies and slow operations. Using nonvolatile devices in processors and memories can realize a faster backup than a conventional volatile computer system, leading to a higher energy efficiency. To evaluate the energy efficiency upon frequent power failures, typical computer systems including processors and memories are designed using 90 nm CMOS or CMOS/magnetic tunnel junction (MTJ) technologies. Nonvolatile ARM Cortex-M0 processors with 4 kB MRAMs are evaluated using a typical computing benchmark program, Dhrystone, which shows a few order-of-magnitude reductions in energy in comparison with a volatile processor with SRAM.

Energy transfer dynamics in Light-Harvesting Dendrimers

NASA Astrophysics Data System (ADS)

Melinger, Joseph S.; McMorrow, Dale; Kleiman, Valeria D.

2002-03-01

We explore energy transfer dynamics in light-harvesting phenylacetylene symmetric and asymmetric dendrimers. Femtosecond pump-probe spectroscopy is used to probe the ultrafast dynamics of electronic excitations in these dendrimers. The backbone of the macromolecule consists of branches of increasing conjugation length, creating an energy gradient, which funnels energy to an accepting perylene trap. In the case of the symmetric dendrimer (nanostar), the energy transfer efficiency is known to approach nearly unity, although the nature and timescale of the energy transfer process is still unknown. For the asymmetric dendrimers, energy transfer efficiencies are very high, with the possibility of more complex transfer processes. We experimentally monitor the transport of excitons through the light-harvesting dendrimer. The transients show a number of components, with timescales ranging from <300fs to several tens of picoseconds, revealing the complex photophysics taking place in these macromolecules. We interpret our results in terms of the Förster mechanism in which energy transfer occurs through dipole-dipole interactions.

Commerical harvest of western juniper and habitat improvement

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nader, G.; Young, J.A.

1994-12-31

Western juniper makes excellent stove wood, but the woodlands are located to far from population centers to make shipment of the relatively low density wood economically feasible. The fibers of juniper wood have been shown in laboratory tests to possess excellent characteristics for the manufacture of molded wood fiber products. The size and growth form of the trees precludes the large scale production of dimensional lumber. The abundant essential oils in the foliage may have commercial value. Certainly the waste from any harvesting and manufacturing process with western juniper would be rich in potential energy. What is proposed is themore » development of a manufacturing process from western juniper biomass, and using the monetary value of this material to pay for the cost of range improvement on the harvested woodlands. The development of such a commercial operation is venture capitalism at its highest level. The potential rewards are the solving of a major environmental problem while providing jobs in rural areas.« less

The effect of sea-water and fresh-water soaking on the quality of Eucheuma sp. syrup and pudding

NASA Astrophysics Data System (ADS)

Novianty, H.; Herandarudewi, S. M. C.

2018-04-01

Eucheuma alvarezii is one of marine commodity with great opportunities to be developed in Indonesia. This seaweed can be used as an additional material in cosmetic and pharmaceutical products or for syrup and pudding. Post-harvest technique conducted by the seaweed farmers will affects the quality of dried and processed products. The purpose of this study was to observe the effect of post harvest technique on the quality of dried seaweed and hedonic test (favorable test) of processed product (syrup and pudding). This study was conducted using descriptive method. The study compared dried, syrup, and puddings from two differents post-harvest technique, between salt and fresh-water draining products. The results showed that fresh-water draining technique obtained better quality results organoleptic test. The results showed that panelist prefered the fresh-water drained products of syrup and pudding. The hedonic scores were much higher for the fresh-water drained products in all three catagories of color, taste, and smell.

Harvesting green algae from eutrophic reservoir by electroflocculation and post-use for biodiesel production.

PubMed

Valero, Enrique; Álvarez, Xana; Cancela, Ángeles; Sánchez, Ángel

2015-01-01

Each year there are more frequent blooms of green algae and cyanobacteria, representing a serious environmental problem of eutrophication. Electroflocculation (EF) was studied to harvest the algae which are present in reservoirs, as well as different factors which may influence on the effectiveness of the process: the voltage applied to the culture medium, run times, electrodes separation and natural sedimentation. Finally, the viability of its use to obtain biodiesel was studied by direct transesterification. The EF process carried out at 10V for 1min, with an electrode separation of 5.5cm and a height of 4cm in culture vessel, obtained a recovery efficiency greater than 95%, and octadecenoic and palmitic acids were obtained as the fatty acid methyl esters (FAMEs). EF is an effective method to harvest green algae during the blooms, obtaining the greatest amount of biomass for subsequent use as a source of biodiesel. Copyright © 2015 Elsevier Ltd. All rights reserved.

RF Power Transfer, Energy Harvesting, and Power Management Strategies

NASA Astrophysics Data System (ADS)

Abouzied, Mohamed Ali Mohamed

Energy harvesting is the way to capture green energy. This can be thought of as a recycling process where energy is converted from one form (here, non-electrical) to another (here, electrical). This is done on the large energy scale as well as low energy scale. The former can enable sustainable operation of facilities, while the latter can have a significant impact on the problems of energy constrained portable applications. Different energy sources can be complementary to one another and combining multiple-source is of great importance. In particular, RF energy harvesting is a natural choice for the portable applications. There are many advantages, such as cordless operation and light-weight. Moreover, the needed infra-structure can possibly be incorporated with wearable and portable devices. RF energy harvesting is an enabling key player for Internet of Things technology. The RF energy harvesting systems consist of external antennas, LC matching networks, RF rectifiers for ac to dc conversion, and sometimes power management. Moreover, combining different energy harvesting sources is essential for robustness and sustainability. Wireless power transfer has recently been applied for battery charging of portable devices. This charging process impacts the daily experience of every human who uses electronic applications. Instead of having many types of cumbersome cords and many different standards while the users are responsible to connect periodically to ac outlets, the new approach is to have the transmitters ready in the near region and can transfer power wirelessly to the devices whenever needed. Wireless power transfer consists of a dc to ac conversion transmitter, coupled inductors between transmitter and receiver, and an ac to dc conversion receiver. Alternative far field operation is still tested for health issues. So, the focus in this study is on near field. The goals of this study are to investigate the possibilities of RF energy harvesting from various sources in the far field, dc energy combining, wireless power transfer in the near field, the underlying power management strategies, and the integration on silicon. This integration is the ultimate goal for cheap solutions to enable the technology for broader use. All systems were designed, implemented and tested to demonstrate proof-of concept prototypes.

An equivalent circuit model of supercapacitors for applications in wireless sensor networks

NASA Astrophysics Data System (ADS)

Yang, Hengzhao; Zhang, Ying

2011-04-01

Energy harvesting technologies have been extensively researched to develop long-lived wireless sensor networks. To better utilize the harvested energy, various energy storage systems are proposed. A simple circuit model is developed to describe supercapacitor behavior, which uses two resistor-capacitor branches with different time constants to characterize the charging and redistribution processes, and a variable leakage resistance (VLR) to characterize the self-discharge process. The voltage and temperature dependence of the VLR values is also discussed. Results show that the VLR model is more accurate than the energy recursive equation (ERE) models for short term wireless sensor network applications.

Flavor formation and character in cocoa and chocolate: a critical review.

PubMed

Afoakwa, Emmanuel Ohene; Paterson, Alistair; Fowler, Mark; Ryan, Angela

2008-10-01

Chocolate characters not only originate in flavor precursors present in cocoa beans, but are generated during post-harvest treatments and transformed into desirable odor notes in the manufacturing processes. Complex biochemical modifications of bean constituents are further altered by thermal reactions in roasting and conching and in alkalization. However, the extent to which the inherent bean constituents from the cocoa genotype, environmental factors, post-harvest treatment, and processing technologies influence chocolate flavor formation and relationships with final flavor quality, has not been clear. With increasing speciality niche products in chocolate confectionery, greater understanding of factors contributing to the variations in flavor character would have significant commercial implications.

Thermoelectric energy harvesting for a solid waste processing toilet

NASA Astrophysics Data System (ADS)

Stokes, C. David; Baldasaro, Nicholas G.; Bulman, Gary E.; Stoner, Brian R.

2014-06-01

Over 2.5 billion people do not have access to safe and effective sanitation. Without a sanitary sewer infrastructure, self-contained modular systems can provide solutions for these people in the developing world and remote areas. Our team is building a better toilet that processes human waste into burnable fuel and disinfects the liquid waste. The toilet employs energy harvesting to produce electricity and does not require external electrical power or consumable materials. RTI has partnered with Colorado State University, Duke University, and Roca Sanitario under a Bill and Melinda Gates Foundation Reinvent the Toilet Challenge (RTTC) grant to develop an advanced stand-alone, self-sufficient toilet to effectively process solid and liquid waste. The system operates through the following steps: 1) Solid-liquid separation, 2) Solid waste drying and sizing, 3) Solid waste combustion, and 4) Liquid waste disinfection. Thermoelectric energy harvesting is a key component to the system and provides the electric power for autonomous operation. A portion of the exhaust heat is captured through finned heat-sinks and converted to electricity by thermoelectric (TE) devices to provide power for the electrochemical treatment of the liquid waste, pumps, blowers, combustion ignition, and controls.

Wastewater treatment to enhance the economic viability of microalgae culture.

PubMed

Pires, J C M; Alvim-Ferraz, M C M; Martins, F G; Simões, M

2013-08-01

Microalgae culture is still not economically viable and it presents some negative environmental impacts, concerning water, nutrient and energy requirements. In this context, this study aims to review the recent advances on microalgal cultures in wastewaters to enhance their economic viability. We focused on three different culture concepts: (1) suspended cell systems, (2) cell immobilization, and (3) microalgae consortia. Cultures with suspended cells are the most studied. The nutrient removal efficiencies are usually high for wastewaters of different sources. However, biomass harvesting is difficult and a costly process due to the small cell size and lower culture density. On the other hand, the cell immobilization systems showed to be the solution for this problem, having as main limitation the nutrient diffusion from bulk to cells, which results in a reduced nutrient removal efficiency. The consortium between microalgae and bacteria enhances the growth of both microorganisms. This culture concept showed to be a promising technology to improve wastewater treatment, regarding not only nutrient removal but also biomass harvesting by bioflocculation. The aggregation mechanism must be studied in depth to find the process parameters that would lead to an effective and cheap harvesting process.

Coupled magneto-electro-mechanical lumped parameter model for a novel vibration-based magneto-electro-elastic energy harvesting systems

NASA Astrophysics Data System (ADS)

Shirbani, Meisam Moory; Shishesaz, Mohammad; Hajnayeb, Ali; Sedighi, Hamid Mohammad

2017-06-01

The objective of this paper is to present a coupled magneto-electro-mechanical (MEM) lumped parameter model for the response of the proposed magneto-electro-elastic (MEE) energy harvesting systems under base excitation. The proposed model can be used to create self-powering systems, which are not limited to a finite battery energy. As a novel approach, the MEE composites are used instead of the conventional piezoelectric materials in order to enhance the harvested electrical power. The considered structure consists of a MEE layer deposited on a layer of non-MEE material, in the framework of unimorph cantilever bars (longitudinal displacement) and beams (transverse displacement). To use the generated electrical potential, two electrodes are connected to the top and bottom surfaces of the MEE layer. Additionally, a stationary external coil is wrapped around the vibrating structure to induce a voltage in the coil by the magnetic field generated in the MEE layer. In order to simplify the design procedure of the proposed energy harvester and obtain closed form solutions, a lumped parameter model is prepared. As a first step in modeling process, the governing constitutive equations, Gauss's and Faraday's laws, are used to derive the coupled MEM differential equations. The derived equations are then solved analytically to obtain the dynamic behavior and the harvested voltages and powers of the proposed energy harvesting systems. Finally, the influences of the parameters that affect the performance of the MEE energy harvesters such as excitation frequency, external resistive loads and number of coil turns are discussed in detail. The results clearly show the benefit of the coil circuit implementation, whereby significant increases in the total useful harvested power as much as 38% and 36% are obtained for the beam and bar systems, respectively.

Optimal power, power limit, and damping of vibration piezoelectric power harvesters

NASA Astrophysics Data System (ADS)

Liao, Yabin; Sodano, Henry

2018-03-01

Power harvesting describes the process of acquiring the ambient energy surrounding a system and converting it into usable electrical energy. Much of the work over the past two decades has focused on the conversion of ambient vibration energy sources using piezoelectric, electromagnetic and electrostatic transduction. Attempts were made to obtain a general model that could be applied to any transduction mechanism. Of the most interest is an electromagnetic generator model that was used by many researchers to model piezoelectric power harvesters. Two major results from the model are the power limit expression and the equal relationship between the electrically induced damping and the mechanical damping to reach the power limit. However, piezoelectric power harvesters cannot be accurately modeled by this electromagnetic model due to the essential difference in physics. There have also been attempts to obtain the power limit expression based on piezoelectric relationships, but they either neglect the piezoelectric backward coupling to the structure, or assume the power limit occurs at the resonance of the system. This paper obtains the power limit expression based on the piezoelectric coupled equations without those assumptions. In addition, the relationship between the electrically induced damping and mechanical damping at the power limit is studied. Furthermore, a closed-form criterion is derived and proposed to define strongly and weakly coupling power harvesters, whose differences in power characteristics are explained through analytical and numerical analysis. While most of the discussion is focused on linear power harvesters connected to a resistive circuit, the aim of this paper is to provide a comprehensive and deep understanding of this simple configuration, answers to important questions, and a starting point to develop a more general theory on power harvesters because similar system characteristics are observed in power harvesters with more complexities.

Comprehensive biocompatibility of nontoxic and high-output flexible energy harvester using lead-free piezoceramic thin film

NASA Astrophysics Data System (ADS)

Jeong, Chang Kyu; Han, Jae Hyun; Palneedi, Haribabu; Park, Hyewon; Hwang, Geon-Tae; Joung, Boyoung; Kim, Seong-Gon; Shin, Hong Ju; Kang, Il-Suk; Ryu, Jungho; Lee, Keon Jae

2017-07-01

Flexible piezoelectric energy harvesters have been regarded as an overarching candidate for achieving self-powered electronic systems for environmental sensors and biomedical devices using the self-sufficient electrical energy. In this research, we realize a flexible high-output and lead-free piezoelectric energy harvester by using the aerosol deposition method and the laser lift-off process. We also investigated the comprehensive biocompatibility of the lead-free piezoceramic device using ex-vivo ionic elusion and in vivo bioimplantation, as well as in vitro cell proliferation and histologic inspection. The fabricated LiNbO3-doped (K,Na)NbO3 (KNN) thin film-based flexible energy harvester exhibited an outstanding piezoresponse, and average output performance of an open-circuit voltage of ˜130 V and a short-circuit current of ˜1.3 μ A under normal bending and release deformation, which is the best record among previously reported flexible lead-free piezoelectric energy harvesters. Although both the KNN and Pb(Zr,Ti)O3 (PZT) devices showed short-term biocompatibility in cellular and histological studies, excessive Pb toxic ions were eluted from the PZT in human serum and tap water. Moreover, the KNN-based flexible energy harvester was implanted into a porcine chest and generated up to ˜5 V and 700 nA from the heartbeat motion, comparable to the output of previously reported lead-based flexible energy harvesters. This work can compellingly serve to advance the development of piezoelectric energy harvesting for actual and practical biocompatible self-powered biomedical applications beyond restrictions of lead-based materials in long-term physiological and clinical aspects.

Long-term effects of timber harvesting on hemicellulolytic microbial populations in coniferous forest soils.

PubMed

Leung, Hilary T C; Maas, Kendra R; Wilhelm, Roland C; Mohn, William W

2016-02-01

Forest ecosystems need to be sustainably managed, as they are major reservoirs of biodiversity, provide important economic resources and modulate global climate. We have a poor knowledge of populations responsible for key biomass degradation processes in forest soils and the effects of forest harvesting on these populations. Here, we investigated the effects of three timber-harvesting methods, varying in the degree of organic matter removal, on putatively hemicellulolytic bacterial and fungal populations 10 or more years after harvesting and replanting. We used stable-isotope probing to identify populations that incorporated (13)C from labeled hemicellulose, analyzing (13)C-enriched phospholipid fatty acids, bacterial 16 S rRNA genes and fungal ITS regions. In soil microcosms, we identified 104 bacterial and 52 fungal hemicellulolytic operational taxonomic units (OTUs). Several of these OTUs are affiliated with taxa not previously reported to degrade hemicellulose, including the bacterial genera Methylibium, Pelomonas and Rhodoferax, and the fungal genera Cladosporium, Pseudeurotiaceae, Capronia, Xenopolyscytalum and Venturia. The effect of harvesting on hemicellulolytic populations was evaluated based on in situ bacterial and fungal OTUs. Harvesting treatments had significant but modest long-term effects on relative abundances of hemicellulolytic populations, which differed in strength between two ecozones and between soil layers. For soils incubated in microcosms, prior harvesting treatments did not affect the rate of incorporation of hemicellulose carbon into microbial biomass. In six ecozones across North America, distributions of the bacterial hemicellulolytic OTUs were similar, whereas distributions of fungal ones differed. Our work demonstrates that diverse taxa in soil are hemicellulolytic, many of which are differentially affected by the impact of harvesting on environmental conditions. However, the hemicellulolytic capacity of soil communities appears resilient.

Long-term effects of timber harvesting on hemicellulolytic microbial populations in coniferous forest soils

PubMed Central

Leung, Hilary T C; Maas, Kendra R; Wilhelm, Roland C; Mohn, William W

2016-01-01

Forest ecosystems need to be sustainably managed, as they are major reservoirs of biodiversity, provide important economic resources and modulate global climate. We have a poor knowledge of populations responsible for key biomass degradation processes in forest soils and the effects of forest harvesting on these populations. Here, we investigated the effects of three timber-harvesting methods, varying in the degree of organic matter removal, on putatively hemicellulolytic bacterial and fungal populations 10 or more years after harvesting and replanting. We used stable-isotope probing to identify populations that incorporated 13C from labeled hemicellulose, analyzing 13C-enriched phospholipid fatty acids, bacterial 16 S rRNA genes and fungal ITS regions. In soil microcosms, we identified 104 bacterial and 52 fungal hemicellulolytic operational taxonomic units (OTUs). Several of these OTUs are affiliated with taxa not previously reported to degrade hemicellulose, including the bacterial genera Methylibium, Pelomonas and Rhodoferax, and the fungal genera Cladosporium, Pseudeurotiaceae, Capronia, Xenopolyscytalum and Venturia. The effect of harvesting on hemicellulolytic populations was evaluated based on in situ bacterial and fungal OTUs. Harvesting treatments had significant but modest long-term effects on relative abundances of hemicellulolytic populations, which differed in strength between two ecozones and between soil layers. For soils incubated in microcosms, prior harvesting treatments did not affect the rate of incorporation of hemicellulose carbon into microbial biomass. In six ecozones across North America, distributions of the bacterial hemicellulolytic OTUs were similar, whereas distributions of fungal ones differed. Our work demonstrates that diverse taxa in soil are hemicellulolytic, many of which are differentially affected by the impact of harvesting on environmental conditions. However, the hemicellulolytic capacity of soil communities appears resilient. PMID:26274049

Exploring the Impacts of Postharvest Processing on the Microbiota and Metabolite Profiles during Green Coffee Bean Production

PubMed Central

De Bruyn, Florac; Zhang, Sophia Jiyuan; Pothakos, Vasileios; Torres, Julio; Lambot, Charles; Moroni, Alice V.; Callanan, Michael; Sybesma, Wilbert; Weckx, Stefan

2016-01-01

ABSTRACT The postharvest treatment and processing of fresh coffee cherries can impact the quality of the unroasted green coffee beans. In the present case study, freshly harvested Arabica coffee cherries were processed through two different wet and dry methods to monitor differences in the microbial community structure and in substrate and metabolite profiles. The changes were followed throughout the postharvest processing chain, from harvest to drying, by implementing up-to-date techniques, encompassing multiple-step metagenomic DNA extraction, high-throughput sequencing, and multiphasic metabolite target analysis. During wet processing, a cohort of lactic acid bacteria (i.e., Leuconostoc, Lactococcus, and Lactobacillus) was the most commonly identified microbial group, along with enterobacteria and yeasts (Pichia and Starmerella). Several of the metabolites associated with lactic acid bacterial metabolism (e.g., lactic acid, acetic acid, and mannitol) produced in the mucilage were also found in the endosperm. During dry processing, acetic acid bacteria (i.e., Acetobacter and Gluconobacter) were most abundant, along with Pichia and non-Pichia (Candida, Starmerella, and Saccharomycopsis) yeasts. Accumulation of associated metabolites (e.g., gluconic acid and sugar alcohols) took place in the drying outer layers of the coffee cherries. Consequently, both wet and dry processing methods significantly influenced the microbial community structures and hence the composition of the final green coffee beans. This systematic approach to dissecting the coffee ecosystem contributes to a deeper understanding of coffee processing and might constitute a state-of-the-art framework for the further analysis and subsequent control of this complex biotechnological process. IMPORTANCE Coffee production is a long process, starting with the harvest of coffee cherries and the on-farm drying of their beans. In a later stage, the dried green coffee beans are roasted and ground in order to brew a cup of coffee. The on-farm, postharvest processing method applied can impact the quality of the green coffee beans. In the present case study, freshly harvested Arabica coffee cherries were processed through wet and dry processing in four distinct variations. The microorganisms present and the chemical profiles of the coffee beans were analyzed throughout the postharvest processing chain. The up-to-date techniques implemented facilitated the investigation of differences related to the method applied. For instance, different microbial groups were associated with wet and dry processing methods. Additionally, metabolites associated with the respective microorganisms accumulated on the final green coffee beans. PMID:27793826

Exploring the Impacts of Postharvest Processing on the Microbiota and Metabolite Profiles during Green Coffee Bean Production.

PubMed

De Bruyn, Florac; Zhang, Sophia Jiyuan; Pothakos, Vasileios; Torres, Julio; Lambot, Charles; Moroni, Alice V; Callanan, Michael; Sybesma, Wilbert; Weckx, Stefan; De Vuyst, Luc

2017-01-01

The postharvest treatment and processing of fresh coffee cherries can impact the quality of the unroasted green coffee beans. In the present case study, freshly harvested Arabica coffee cherries were processed through two different wet and dry methods to monitor differences in the microbial community structure and in substrate and metabolite profiles. The changes were followed throughout the postharvest processing chain, from harvest to drying, by implementing up-to-date techniques, encompassing multiple-step metagenomic DNA extraction, high-throughput sequencing, and multiphasic metabolite target analysis. During wet processing, a cohort of lactic acid bacteria (i.e., Leuconostoc, Lactococcus, and Lactobacillus) was the most commonly identified microbial group, along with enterobacteria and yeasts (Pichia and Starmerella). Several of the metabolites associated with lactic acid bacterial metabolism (e.g., lactic acid, acetic acid, and mannitol) produced in the mucilage were also found in the endosperm. During dry processing, acetic acid bacteria (i.e., Acetobacter and Gluconobacter) were most abundant, along with Pichia and non-Pichia (Candida, Starmerella, and Saccharomycopsis) yeasts. Accumulation of associated metabolites (e.g., gluconic acid and sugar alcohols) took place in the drying outer layers of the coffee cherries. Consequently, both wet and dry processing methods significantly influenced the microbial community structures and hence the composition of the final green coffee beans. This systematic approach to dissecting the coffee ecosystem contributes to a deeper understanding of coffee processing and might constitute a state-of-the-art framework for the further analysis and subsequent control of this complex biotechnological process. Coffee production is a long process, starting with the harvest of coffee cherries and the on-farm drying of their beans. In a later stage, the dried green coffee beans are roasted and ground in order to brew a cup of coffee. The on-farm, postharvest processing method applied can impact the quality of the green coffee beans. In the present case study, freshly harvested Arabica coffee cherries were processed through wet and dry processing in four distinct variations. The microorganisms present and the chemical profiles of the coffee beans were analyzed throughout the postharvest processing chain. The up-to-date techniques implemented facilitated the investigation of differences related to the method applied. For instance, different microbial groups were associated with wet and dry processing methods. Additionally, metabolites associated with the respective microorganisms accumulated on the final green coffee beans. Copyright © 2016 American Society for Microbiology.

N cycling and the composition of terpenes and tannins in boreal forest soils: Effects of logging residues

NASA Astrophysics Data System (ADS)

Smolander, Aino; Kitunen, Veikko; Kukkola, Mikko; Tamminen, Pekka

2014-05-01

There is increasing evidence available that certain terpenes and tannins may mediate substantial changes in nitrogen cycling processes in boreal forest soils. Terpenes and tannins are two important groups of plant secondary metabolites: Terpenes are hydrocarbons having different number of isoprene-derived units and tannins are complex polyphenolic compounds able to interact with proteins. Logging residues, consisting of fresh tree tops and branches with needles contain large amounts of terpenes and tannins. Currently there is increasing demand for forest biomass for bioenergy production. Therefore, harvesting of logging residues has become more common from both clear-cutting and thinning stands, instead of conventional stem-only harvest where logging residues are retained on the site. Our aim was to determine how logging residues affect soil N cycling processes in Scots pine and Norway spruce thinning stands in long-term, and how these processes are related to the composition of terpenes and tannins in the soil. Samples were taken from the humus layer of pine and spruce experiments which had been thinned 4-to-19 years before; in the thinning different amounts of logging residues had been distributed on the plots. Logging residues had only little effect on soil microbial biomass N or C. However, in several sites logging residues increased the rate of net N mineralization and the ratios net N mineralization/ C mineralization and net N mineralization/microbial biomass N, and these positive effects were very long-lasting. Logging residues also changed the composition of different terpenes and condensed tannins in soil. In general, with regard to the processes and ratios indicating N availability, stem-only harvest seems to be more favorable than whole-tree harvest. The results from long-term field experiments will be discussed in relation to the effects of different terpenes and tannins, observed in short-term laboratory experiments, on N cycling processes.

Performance of a cut-to-length harvester in a single-tree and group selection cut

Treesearch

Neil K. Huyler; Chris LeDoux

1999-01-01

Presents production and cost data for a mechanized and cut-to-length (CTL) harvester used in a single-tree and group-selection cut on the Groton State Forest in central Vermont. For trees whose average volume (size) was 7 to 18 ft3, production ranged from 464 to 734 ft3 per productive machine hour (PMH). The cycle time for processing trees into bunches to forward to a...

Enhanced mechanical energy harvesting ability of electrospun poly(vinylidene fluoride)/hectorite clay nanocomposites

NASA Astrophysics Data System (ADS)

Rahman, Wahida; Ghosh, Sujoy Kumar; Middya, Tapas Ranjan; Mandal, Dipankar

2018-04-01

We report on enhanced piezoelectric properties of poly (vinylidene fluoride) (PVDF)/hectorite nano-clay composites prepared by electrospinning process. The investigation on the effects of the nano-filler in the crystalline phase and piezoelectric properties reveals dramatic enhancement of piezoelectric β-phase (95%) due to synergistic effect of electrospinning and nano-clay loading. As a result, the prepared nanocomposite possesses higher mechanical energy harvesting ability than that of pure PVDF.

Stretchable Porous Carbon Nanotube-Elastomer Hybrid Nanocomposite for Harvesting Mechanical Energy.

PubMed

Fan, You Jun; Meng, Xian Song; Li, Hua Yang; Kuang, Shuang Yang; Zhang, Lei; Wu, Ying; Wang, Zhong Lin; Zhu, Guang

2017-01-01

A stretchable porous nanocomposite (PNC) is reported based on a hybrid of a multiwalled carbon nanotubes network and a poly(dimethylsiloxane) matrix for harvesting energy from mechanical interactions. The deformation-enabled energy-generating process makes the PNC applicable to various mechanical interactions, including pressing, stretching, bending, and twisting. It can be potentially used as an energy solution for wearable electronics. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Yield and utilization of hardwood fiber grown on short rotations. [Platanus occidentalis, Liquidambar styraciflua, Liriodendron tulipifera

DOE Office of Scientific and Technical Information (OSTI.GOV)

Steinbeck, K.; Brown, C.L.

1976-01-01

Plantations of broad-leaved tree species harvested in cycles of less than 10 years can help meet man's increasing cellulose and energy needs. A system of growing hardwoods like an agricultural row crop, harvested with equipment equivalent to corn silage cutters and using the ensuing sprout growth as the next crop, was conceived by foresters in Georgia in 1965. Research has focused on the tree species, sites, and cultural practices suited for this concept as well as the biomass yields and the utility of the fiber that was produced. About 70 hectares of American sycamore (Platanus occidentalis L.), sweetgum (Liquidambar styracifluamore » L.), and yellow poplar (Liriodendron tulipifera L.) test plantings have been established in the Piedmont and Coastal Plain regions of Georgia. These species, when given proper care, can be grown successfully on many sites previously deemed unsuitable for hardwood growth. Stumps will resprout throughout the year, ensuring a continuous flow of raw material to the user. The biomass yields from hardwood fields vary with species, site, cultural practices, and rotation age. Fresh weight yields of unfoliated sycamore sprouts grown on an upland site varied from 14.3 tons/ha/yr when harvested annually to 21.8 tons/ha/yr with harvest at age four. When sprouts were harvested every two years, 46 kg/ha/2 yrs of nitrogen, 35 kg calcium, 22 kg potassium, and 6 kg phosphorus were removed in the harvested material. Juvenile American sycamore stump sprouts have been successfully converted into corrugating medium, particleboard, fiberboard, hardboard, and newsprint. It can be cooked by the Kraft and NSSC processes. One-, two-, and four-year-old sycamore sprouts presented no unusual problems in the Kraft process, and yields ranged from 45 to 57 percent with an average yield of 52 percent. Cooking times were relatively short.« less

Low Temperature and Short-Term High-CO2 Treatment in Postharvest Storage of Table Grapes at Two Maturity Stages: Effects on Transcriptome Profiling

PubMed Central

Rosales, Raquel; Romero, Irene; Fernandez-Caballero, Carlos; Escribano, M. Isabel; Merodio, Carmen; Sanchez-Ballesta, M. Teresa

2016-01-01

Table grapes (Vitis vinifera cv. Cardinal) are highly perishable and their quality deteriorates during postharvest storage at low temperature mainly because of sensitivity to fungal decay and senescence of rachis. The application of a 3-day CO2 treatment (20 kPa CO2 + 20 kPa O2 + 60 kPa N2) at 0°C reduced total decay and retained fruit quality in early and late-harvested table grapes during postharvest storage. In order to study the transcriptional responsiveness of table grapes to low temperature and high CO2 levels in the first stage of storage and how the maturity stage affect these changes, we have performed a comparative large-scale transcriptional analysis using the custom-made GrapeGen GeneChip®. In the first stage of storage, low temperature led to a significantly intense change in grape skin transcriptome irrespective of fruit maturity, although there were different changes within each stage. In the case of CO2 treated samples, in comparison to fruit at time zero, only slight differences were observed. Functional enrichment analysis revealed that major modifications in the transcriptome profile of early- and late-harvested grapes stored at 0°C are linked to biotic and abiotic stress-responsive terms. However, in both cases there is a specific reprogramming of the transcriptome during the first stage of storage at 0°C in order to withstand the cold stress. Thus, genes involved in gluconeogenesis, photosynthesis, mRNA translation and lipid transport were up-regulated in the case of early-harvested grapes, and genes related to protein folding stability and intracellular membrane trafficking in late-harvested grapes. The beneficial effect of high CO2 treatment maintaining table grape quality seems to be an active process requiring the induction of several transcription factors and kinases in early-harvested grapes, and the activation of processes associated to the maintenance of energy in late-harvested grapes. PMID:27468290

Adaptive harvest management for the Svalbard population of pink-footed geese: assessment for the 2013-2015 hunting seasons

USGS Publications Warehouse

Johnson, Fred A.; Madsen, Jesper

2013-01-01

This report describes progress on the development of an adaptive harvestmanagement strategy for maintaining the Svalbard population of pink-footed geese near their agreed target level (60,000) by providing for sustainable harvests in Norway and Denmark. Specifically, this report provides an optimal harvest quota for the 2013-2015 hunting seasons and describes a process for evaluating whether emergency hunting closures would be needed during that period. By combining varying hypotheses about survival and reproduction, a suite of nine models have been developed that represent a wide range of possibilities concerning the extent to which demographic rates are density dependent or independent, and the extent to which spring temperatures are important. The most current set of monitoring information was used to update model weights for the 1991 – 2012 period. Current model weights suggest no evidence for density-dependent survival. These results suggest that the pink-footed goose population may have recently experienced a release from density-dependent mechanisms, corresponding to the period of most rapid growth in population size. There was equivocal evidence for the effect of May temperature days (number of days with temperatures above freezing) on survival and on reproduction. The optimal harvest strategy suggests that the appropriate annual harvest quota for the 20132015 period is 15,000; hence there is no need to take emergency measures to close the upcoming hunting season. For comparison, the estimated harvest in 2012 was 11,000. If the harvest quota of 15,000 were met, the autumn 2013 population count is expected to be 76,000. If only the most recent 3-year mean harvest were realized (11,500), an autumn population size of 80,000 thousand is expected. Thus, it may be that harvest is approaching the magnitude needed to stabilize the population.

A scanning electron microscope study and statistical analysis of adipocyte morphology in lipofilling: comparing the effects of harvesting and purification procedures with 2 different techniques.

PubMed

Rubino, Corrado; Mazzarello, Vittorio; Faenza, Mario; Montella, Andrea; Santanelli, Fabio; Farace, Francesco

2015-06-01

The aim of this study was to evaluate the effects on adipocyte morphology of 2 techniques of fat harvesting and of fat purification in lipofilling, considering that the number of viable healthy adipocytes is important in fat survival in recipient areas of lipofilling. Fat harvesting was performed in 10 female patients from flanks, on one side with a 2-mm Coleman cannula and on the other side with a 3-mm Mercedes cannula. Thirty milliliter of fat tissue from each side was collected and divided into three 10 mL syringes: A, B, and C. The fat inside syringe A was left untreated, the fat in syringe B underwent simple sedimentation, and the fat inside syringe C underwent centrifugation at 3000 rpm for 3 minutes. Each fat graft specimen was processed for examination under low-vacuum scanning electron microscope. Diameter (μ) and number of adipocytes per square millimeter and number of altered adipocytes per square millimeter were evaluated. Untreated specimens harvested with the 2 different techniques were first compared, then sedimented versus centrifuged specimens harvested with the same technique were compared. Statistical analysis was performed using Wilcoxon signed rank test. The number of adipocytes per square millimeter was statistically higher in specimens harvested with the 3-mm Mercedes cannula (P = 0.0310). The number of altered cells was statistically higher in centrifuged specimens than in sedimented ones using both methods of fat harvesting (P = 0.0080) with a 2-mm Coleman cannula and (P = 0.0050) with a 3-mm Mercedes cannula. Alterations in adipocyte morphology consisted in wrinkling of the membrane, opening of pore with leakage of oily material, reduction of cellular diameter, and total collapse of the cellular membrane. Fat harvesting by a 3-mm cannula results in a higher number of adipocytes and centrifugation of the harvested fat results in a higher number of morphologic altered cells than sedimentation.

Renewal of Collaborative Research: Economically Viable Forest Harvesting Practices That Increase Carbon Sequestration

DOE Office of Scientific and Technical Information (OSTI.GOV)

Davidson, E.A.; Dail, D.B., Hollinger, D.; Scott, N.

Forests provide wildlife habitat, water and air purification, climate moderation, and timber and nontimber products. Concern about climate change has put forests in the limelight as sinks of atmospheric carbon. The C stored in the global vegetation, mostly in forests, is nearly equivalent to the amount present in atmospheric CO{sub 2}. Both voluntary and government-mandated carbon trading markets are being developed and debated, some of which include C sequestration resulting from forest management as a possible tradeable commodity. However, uncertainties regarding sources of variation in sequestration rates, validation, and leakage remain significant challenges for devising strategies to include forest managementmore » in C markets. Hence, the need for scientifically-based information on C sequestration by forest management has never been greater. The consequences of forest management on the US carbon budget are large, because about two-thirds of the {approx}300 million hectare US forest resource is classified as 'commercial forest.' In most C accounting budgets, forest harvesting is usually considered to cause a net release of C from the terrestrial biosphere to the atmosphere. However, forest management practices could be designed to meet the multiple goals of providing wood and paper products, creating economic returns from natural resources, while sequestering C from the atmosphere. The shelterwood harvest strategy, which removes about 30% of the basal area of the overstory trees in each of three successive harvests spread out over thirty years as part of a stand rotation of 60-100 years, may improve net C sequestration compared to clear-cutting because: (1) the average C stored on the land surface over a rotation increases, (2) harvesting only overstory trees means that a larger fraction of the harvested logs can be used for long-lived sawtimber products, compared to more pulp resulting from clearcutting, (3) the shelterwood cut encourages growth of subcanopy trees by opening up the forest canopy to increasing light penetration. Decomposition of onsite harvest slash and of wastes created during timber processing releases CO{sub 2} to the atmosphere, thus offsetting some of the C sequestered in vegetation. Decomposition of soil C and dead roots may also be temporarily stimulated by increased light penetration and warming of the forest floor. Quantification of these processes and their net effect is needed. We began studying C sequestration in a planned shelterwood harvest at the Howland Forest in central Maine in 2000. The harvest took place in 2002 by the International Paper Corporation, who assisted us to track the fates of harvest products (Scott et al., 2004, Environmental Management 33: S9-S22). Here we present the results of intensive on-site studies of the decay of harvest slash, soil respiration, growth of the remaining trees, and net ecosystem exchange (NEE) of CO{sub 2} during the first six years following the harvest. These results are combined with calculations of C in persisting off-site harvest products to estimate the net C consequences to date of this commercial shelterwood harvest operation. Tower-based eddy covariance is an ideal method for this study, as it integrates all C fluxes in and out of the forest over a large 'footprint' area and can reveal how the net C flux, as well as gross primary productivity and respiration, change following harvest. Because the size of this experiment precludes large-scale replication, we are use a paired-airshed approach, similar to classic large-scale paired watershed experiments. Measurements of biomass and C fluxes in control and treatment stands were compared during a pre-treatment calibration period, and then divergence from pre-treatment relationships between the two sites measured after the harvest treatment. Forests store carbon (C) as they accumulate biomass. Many forests are also commercial sources of timber and wood fiber. In most C accounting budgets, forest harvesting is usually considered to cause a net release of C from the terrestrial biosphere to the atmosphere. However, it might also be possible for commercial use of forests to contribute to terrestrial sequestration of C. The objective of the our research project is to determine whether shelterwood cutting regimes now being adopted in the commercial forests of Maine and other areas of the country can achieve these multiple goals.« less

Triboelectric effect in energy harvesting

NASA Astrophysics Data System (ADS)

Logothetis, I.; Vassiliadis, S.; Siores, E.

2017-10-01

With the development of wearable technology, much research has been undertaken in the field of flexible and stretchable electronics for use in interactive attire. The challenging problem wearable technology faces is the ability to provide energy whilst keeping the endproduct comfortable, light, ergonomic and nonintrusive. Energy harvesting, or energy scavenging as it is also known, is the process by which ambient energy is captured and converted into electric energy. The triboelectric effect converts mechanical energy into electrical energy based on the coupling effect of triboelectrification and electrostatic induction and is utilized as the basis for triboelectric generators (TEG). TEG’s are promising for energy harvesting due their high output power and efficiency in conjunction with simple and economical production. Due to the wide availability of materials and ease of integration, in order to produce the triboelectric effect such functional materials are effective for wearable energy harvesting systems. Flexible TEG’s can be built and embedded into attire, although a thorough understanding of the underlying principle of how TEG’s operate needs to be comprehended for the development and in incorporation in smart technical textiles. This paper presents results associated with TEG’S and discusses their suitability for energy harvesting in textiles structures.

County-level Estimates for Carbon Distribution in U.S. Croplands, 1990-2005

DOE Data Explorer

West, Tristram O. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2008-01-01

Net Primary Productivity (NPP) for croplands can be estimated using a statistical method that includes factors for dry weight, harvest indices, and root:shoot ratios multiplied by yield data from the National Agricultural Statistics Service (NASS). This method has been documented and published by Prince et al. (2001), Hicke and Lobell (2004), and Hicke et al. (2004). We expanded this method by including factors for more crops and by using an estimated carbon content of 0.45 for agricultural crops to estimate (a) total net carbon uptake, (b) carbon in aboveground biomass, (c) carbon in belowground biomass, (d) carbon harvested and transported off site, and (e) the amount of carbon remaining on the surface following harvest. These five variables are included with their respective Federal Information Processing Standards (FIPS) codes for all counties in the contiguous U.S. from 1990-2005. A mean harvest efficiency of 0.95 was assumed across all crops. Total cropland NPP for the U.S. ranges from 378-527 Tg C yr^-1 within years 1990-2005, and total carbon harvested and removed ranges from 161-228 Tg C yr^-1 within years 1990-2005.

Impact of different post-harvest processing methods on the chemical compositions of peony root.

PubMed

Zhu, Shu; Shirakawa, Aimi; Shi, Yanhong; Yu, Xiaoli; Tamura, Takayuki; Shibahara, Naotoshi; Yoshimatsu, Kayo; Komatsu, Katsuko

2018-06-01

The impact of key processing steps such as boiling, peeling, drying and storing on chemical compositions and morphologic features of the produced peony root was investigated in detail by applying 15 processing methods to fresh roots of Paeonia lactiflora and then monitoring contents of eight main components, as well as internal root color. The results showed that low temperature (4 °C) storage of fresh roots for approximately 1 month after harvest resulted in slightly increased and stable content of paeoniflorin, which might be due to suppression of enzymatic degradation. This storage also prevented roots from discoloring, facilitating production of favorable bright color roots. Boiling process triggered decomposition of polygalloylglucoses, thereby leading to a significant increase in contents of pentagalloylglucose and gallic acid. Peeling process resulted in a decrease of albiflorin and catechin contents. As a result, an optimized and practicable processing method ensuring high contents of the main active components in the produced root was developed.

Stream Mercury Export in Response to Contemporary Timber Harvesting Methods (Pacific Coastal Mountains, Oregon, USA).

PubMed

Eckley, Chris S; Eagles-Smith, Collin; Tate, Michael T; Kowalski, Brandon; Danehy, Robert; Johnson, Sherri L; Krabbenhoft, David P

2018-02-20

Land-use activities can alter hydrological and biogeochemical processes that can affect the fate, transformation, and transport of mercury (Hg). Previous studies in boreal forests have shown that forestry operations can have profound but variable effects on Hg export and methylmercury (MeHg) formation. The Pacific Northwest is an important timber producing region that receives large atmospheric Hg loads, but the impact of forest harvesting on Hg mobilization has not been directly studied and was the focus of our investigation. Stream discharge was measured continuously, and Hg and MeHg concentrations were measured monthly for 1.5 years following logging in three paired harvested and unharvested (control) catchments. There was no significant difference in particulate-bound Hg concentrations or loads in the harvested and unharvested catchments which may have resulted from forestry practices aimed at minimizing erosion. However, the harvested catchments had significantly higher discharge (32%), filtered Hg concentrations (28%), filtered Hg loads (80%), and dissolved organic carbon (DOC) loads (40%) compared to forested catchments. MeHg concentrations were low (mostly <0.05 ng L -1 ) in harvested, unharvested, and downstream samples due to well-drained/unsaturated soil conditions and steep slopes with high energy eroding stream channels that were not conducive to the development of anoxic conditions that support methylation. These results have important implications for the role forestry operations have in affecting catchment retention and export of Hg pollution.

Sexual reproduction of the Hawaiian black coral Antipathes griggi (Cnidaria: Antipatharia)

NASA Astrophysics Data System (ADS)

Wagner, D.; Waller, R. G.; Montgomery, A. D.; Kelley, C. D.; Toonen, R. J.

2012-09-01

The Hawaiian black coral fishery has maintained steady catch levels for over 50 years. However, recent declines in the biomass of commercially valuable Hawaiian black corals question whether regulations need to be redefined for sustainable harvesting. Fishery management efforts are complicated by the limited information on the basic life history and reproduction of black corals. To address this knowledge gap, we used histological techniques to investigate sexual reproductive processes within Antipathes griggi, the dominant species targeted by the fishery. Our results indicate that A. griggi is likely gonochoric with a 1:1 sex ratio and has an annual reproductive cycle. Furthermore, the percentage of polyps containing gametes dropped continuously throughout the reproductive season, indicating that spawning occurs in successive events with greatest intensity between November and December. Current fishing regulations prohibit harvesting of colonies <90 cm in height in state waters, and colonies <120 cm in height in federal waters. This study indicates that ~80% meeting the state harvesting limit, and ~90% of colonies meeting the federal limit, are sexually mature. Therefore, increasing these minimum size harvesting limits would ensure that more colonies can reproduce before being exposed to fishing mortality. Although A. griggi can be found to depths of 100 m, it is rare below the 75 m depth limit at which commercial harvest occurs in Hawai`i. Thus, the supposed depth refuge from harvest does not really exist.

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

John "JC" Carver, a payload integration engineer with NASA Kennedy Space Center's Test and Operations Support Contract, opens the door to the growth chamber of the Advanced Plant Habitat (APH) Flight Unit No. 1 for a test harvest of half of the Arabidopsis thaliana plants growing within. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in Kennedy's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

John "JC" Carver, a payload integration engineer with NASA Kennedy Space Center's Test and Operations Support Contract, places Arabidopsis thaliana plants harvested from the Advanced Plant Habitat (APH) Flight Unit No. 1 into a Mini ColdBag that quickly freezes the plants. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in Kennedy's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

John "JC" Carver, a payload integration engineer with NASA Kennedy Space Center's Test and Operations Support Contract, places Arabidopsis thaliana plants harvested from the Advanced Plant Habitat (APH) Flight Unit No. 1 into an Ultra-low Freezer chilled to -150 degrees Celsius. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in Kennedy's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Demographic threats to the sustainability of Brazil nut exploitation.

PubMed

Peres, Carlos A; Baider, Claudia; Zuidema, Pieter A; Wadt, Lúcia H O; Kainer, Karen A; Gomes-Silva, Daisy A P; Salomão, Rafael P; Simões, Luciana L; Franciosi, Eduardo R N; Cornejo Valverde, Fernando; Gribel, Rogério; Shepard, Glenn H; Kanashiro, Milton; Coventry, Peter; Yu, Douglas W; Watkinson, Andrew R; Freckleton, Robert P

2003-12-19

A comparative analysis of 23 populations of the Brazil nut tree (Bertholletia excelsa) across the Brazilian, Peruvian, and Bolivian Amazon shows that the history and intensity of Brazil nut exploitation are major determinants of population size structure. Populations subjected to persistent levels of harvest lack juvenile trees less than 60 centimeters in diameter at breast height; only populations with a history of either light or recent exploitation contain large numbers of juvenile trees. A harvesting model confirms that intensive exploitation levels over the past century are such that juvenile recruitment is insufficient to maintain populations over the long term. Without management, intensively harvested populations will succumb to a process of senescence and demographic collapse, threatening this cornerstone of the Amazonian extractive economy.

Insights into characteristics, sources, and evolution of submicron aerosols during harvest seasons in the Yangtze River delta region, China

NASA Astrophysics Data System (ADS)

Zhang, Y. J.; Tang, L. L.; Wang, Z.; Yu, H. X.; Sun, Y. L.; Liu, D.; Qin, W.; Canonaco, F.; Prévôt, A. S. H.; Zhang, H. L.; Zhou, H. C.

2015-02-01

Atmospheric submicron particulate matter (PM1) is one of the most significant pollution components in China. Despite its current popularity in the studies of aerosol chemistry, the characteristics, sources and evolution of atmospheric PM1 species are still poorly understood in China, particularly for the two harvest seasons, namely, the summer wheat harvest and autumn rice harvest. An Aerodyne Aerosol Chemical Speciation Monitor (ACSM) was deployed for online monitoring of PM1 components during summer and autumn harvest seasons in urban Nanjing, in the Yangtze River delta (YRD) region of China. PM1 components were shown to be dominated by organic aerosol (OA, 39 and 41%) and nitrate (23 and 20%) during the harvest seasons (the summer and autumn harvest). Positive matrix factorization (PMF) analysis of the ACSM OA mass spectra resolved four OA factors: hydrocarbon-like mixed with cooking-related OA (HOA + COA), fresh biomass-burning OA (BBOA), oxidized biomass-burning-influenced OA (OOA-BB), and highly oxidized OA (OOA); in particular the oxidized BBOA contributes ~80% of the total BBOA loadings. Both fresh and oxidized BBOA exhibited apparent diurnal cycles with peak concentration at night, when the high ambient relative humidity and low temperature facilitated the partitioning of semi-volatile organic species into the particle phase. The fresh BBOA concentrations for the harvests are estimated as BBOA = 15.1 × (m/z 60-0.26% × OA), where m/z (mass-to-charge ratio) 60 is a marker for levoglucosan-like species. The (BBOA + OOA-BB)/ΔCO, (ΔCO is the CO minus background CO), decreases as a function of f44 (fraction of m/z 44 in OA signal), which might indicate that BBOA was oxidized to less volatile OOA, e.g., more aged and low volatility OOA (LV-OOA) during the aging process. Analysis of air mass back trajectories indicates that the high BB pollutant concentrations are linked to the air masses from the western (summer harvest) and southern (autumn harvest) areas.

Optimal throughput for cognitive radio with energy harvesting in fading wireless channel.

PubMed

Vu-Van, Hiep; Koo, Insoo

2014-01-01

Energy resource management is a crucial problem of a device with a finite capacity battery. In this paper, cognitive radio is considered to be a device with an energy harvester that can harvest energy from a non-RF energy resource while performing other actions of cognitive radio. Harvested energy will be stored in a finite capacity battery. At the start of the time slot of cognitive radio, the radio needs to determine if it should remain silent or carry out spectrum sensing based on the idle probability of the primary user and the remaining energy in order to maximize the throughput of the cognitive radio system. In addition, optimal sensing energy and adaptive transmission power control are also investigated in this paper to effectively utilize the limited energy of cognitive radio. Finding an optimal approach is formulated as a partially observable Markov decision process. The simulation results show that the proposed optimal decision scheme outperforms the myopic scheme in which current throughput is only considered when making a decision.

Identification of coffee leaves using FT-NIR spectroscopy and SIMCA.

PubMed

Mees, Corenthin; Souard, Florence; Delporte, Cedric; Deconinck, Eric; Stoffelen, Piet; Stévigny, Caroline; Kauffmann, Jean-Michel; De Braekeleer, Kris

2018-01-15

Abundant literature has been devoted to coffee beans (green or roasted) chemical description but relatively few studies have been devoted to coffee leaves. Given the fact that coffee leaves are used for food and medicinal consumption, it was of interest to develop a rapid screening method in order to identify coffee leaves taxa. Investigation by Fourier - Transform near infrared spectroscopy (FT-NIRS) was performed on nine Coffea taxa leaves harvested over one year in a tropical greenhouse of the Botanic Garden Meise (Belgium). The only process after leaves harvesting was an effective drying and a homogeneous leaves grinding. FT-NIRS with SIMCA analysis allowed to discriminate the spectral profiles across taxon, aging stage (mature and senescence coffee leaves) and harvest period. This study showed that it was possible (i) to classify the different taxa, (ii) to identify their aging stage and (iii) to identify the harvest period for the mature stage with a correct classification rate of 99%, 100% and 90%, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

Study on fault diagnosis and load feedback control system of combine harvester

NASA Astrophysics Data System (ADS)

Li, Ying; Wang, Kun

2017-01-01

In order to timely gain working status parameters of operating parts in combine harvester and improve its operating efficiency, fault diagnosis and load feedback control system is designed. In the system, rotation speed sensors were used to gather these signals of forward speed and rotation speeds of intermediate shaft, conveying trough, tangential and longitudinal flow threshing rotors, grain conveying auger. Using C8051 single chip microcomputer (SCM) as processor for main control unit, faults diagnosis and forward speed control were carried through by rotation speed ratio analysis of each channel rotation speed and intermediate shaft rotation speed by use of multi-sensor fused fuzzy control algorithm, and these processing results would be sent to touch screen and display work status of combine harvester. Field trials manifest that fault monitoring and load feedback control system has good man-machine interaction and the fault diagnosis method based on rotation speed ratios has low false alarm rate, and the system can realize automation control of forward speed for combine harvester.

Harvesting microalgal biomass using a magnetically induced membrane vibration (MMV) system: filtration performance and energy consumption.

PubMed

Bilad, M R; Discart, V; Vandamme, D; Foubert, I; Muylaert, K; Vankelecom, Ivo F J

2013-06-01

This study was performed to investigate the effectiveness of submerged microfiltration to harvest both a marine diatom Phaeodactylum tricornutum and a Chlorella vulgaris in a recently developed magnetically induced membrane vibrating (MMV) system. We assess the filtration performance by conducting the improved flux step method (IFM), fed-batch concentration filtrations and membrane fouling autopsy using two lab-made membranes with different porosity. The full-scale energy consumption was also estimated. Overall results suggest that the MMV offers a good fouling control and the process was proven to be economically attractive. By combining the membrane filtration (15× concentration) with centrifugation to reach a final concentration of 25% w/v, the energy consumption to harvest P. tricornutum and C. vulgaris was, respectively, as low as 0.84 and 0.77kWh/m(3), corresponding to 1.46 and 1.39 kWh/kg of the harvested biomass. Copyright © 2013 Elsevier Ltd. All rights reserved.

Piezoelectric polymer multilayer on flexible substrate for energy harvesting.

PubMed

Zhang, Lei; Oh, Sharon Roslyn; Wong, Ting Chong; Tan, Chin Yaw; Yao, Kui

2013-09-01

A piezoelectric polymer multilayer structure formed on a flexible substrate is investigated for mechanical energy harvesting under bending mode. Analytical and numerical models are developed to clarify the effect of material parameters critical to the energy harvesting performance of the bending multilayer structure. It is shown that the maximum power is proportional to the square of the piezoelectric stress coefficient and the inverse of dielectric permittivity of the piezoelectric polymer. It is further found that a piezoelectric multilayer with thinner electrodes can generate more electric energy in bending mode. The effect of improved impedance matching in the multilayer polymer on energy output is remarkable. Comparisons between piezoelectric ceramic multilayers and polymer multilayers on flexible substrate are discussed. The fabrication of a P(VDF-TrFE) multilayer structure with a thin Al electrode layer is experimentally demonstrated by a scalable dip-coating process on a flexible aluminum substrate. The results indicate that it is feasible to produce a piezoelectric polymer multilayer structure on flexible substrate for harvesting mechanical energy applicable for many low-power electronics.

Hydrophobic/Hydrophilic Cooperative Janus System for Enhancement of Fog Collection.

PubMed

Cao, Moyuan; Xiao, Jiasheng; Yu, Cunming; Li, Kan; Jiang, Lei

2015-09-09

Harvesting micro-droplets from fog is a promising method for solving global freshwater crisis. Different types of fog collectors have been extensively reported during the last decade. The improvement of fog collection can be attributed to the immediate transportation of harvested water, the effective regeneration of the fog gathering surface, etc. Through learning from the nature's strategy for water preservation, the hydrophobic/hydrophilic cooperative Janus system that achieved reinforced fog collection ability is reported here. Directional delivery of the surface water, decreased re-evaporation rate of the harvested water, and thinner boundary layer of the collecting surface contribute to the enhancement of collection efficiency. Further designed cylinder Janus collector can facilely achieve a continuous process of efficient collection, directional transportation, and spontaneous preservation of fog water. This Janus fog harvesting system should improve the understanding of micro-droplet collection system and offer ideas to solve water resource crisis. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and Functional Reconstitution of Light-Harvesting Complex II into Polymeric Membrane Architectures.

PubMed

Zapf, Thomas; Tan, Cherng-Wen Darren; Reinelt, Tobias; Huber, Christoph; Shaohua, Ding; Geifman-Shochat, Susana; Paulsen, Harald; Sinner, Eva-Kathrin

2015-12-01

One of most important processes in nature is the harvesting and dissipation of solar energy with the help of light-harvesting complex II (LHCII). This protein, along with its associated pigments, is the main solar-energy collector in higher plants. We aimed to generate stable, highly controllable, and sustainable polymer-based membrane systems containing LHCII-pigment complexes ready for light harvesting. LHCII was produced by cell-free protein synthesis based on wheat-germ extract, and the successful integration of LHCII and its pigments into different membrane architectures was monitored. The unidirectionality of LHCII insertion was investigated by protease digestion assays. Fluorescence measurements indicated chlorophyll integration in the presence of LHCII in spherical as well as planar bilayer architectures. Surface plasmon enhanced fluorescence spectroscopy (SPFS) was used to reveal energy transfer from chlorophyll b to chlorophyll a, which indicates native folding of the LHCII proteins. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficient harvesting of marine Chlorella vulgaris microalgae utilizing cationic starch nanoparticles by response surface methodology.

PubMed

Bayat Tork, Mahya; Khalilzadeh, Rasoul; Kouchakzadeh, Hasan

2017-11-01

Harvesting involves nearly thirty percent of total production cost of microalgae that needs to be done efficiently. Utilizing inexpensive and highly available biopolymer-based flocculants can be a solution for reducing the harvest costs. Herein, flocculation process of Chlorella vulgaris microalgae using cationic starch nanoparticles (CSNPs) was evaluated and optimized through the response surface methodology (RSM). pH, microalgae and CSNPs concentrations were considered as the main independent variables. Under the optimum conditions of microalgae concentration 0.75gdry weight/L, CSNPs concentration 7.1mgdry weight/L and pH 11.8, the maximum flocculation efficiency (90%) achieved. Twenty percent increase in flocculation efficiency observed with the use of CSNPs instead of the non-particulate starch which can be due to the more electrostatic interactions between the cationic nanoparticles and the microalgae. Therefore, the synthesized CSNPs can be employed as a convenient and economical flocculants for efficient harvest of Chlorella vulgaris microalgae at large scale. Copyright © 2017 Elsevier Ltd. All rights reserved.

HEMATOPOIETIC PROGENITOR CELL CONTENT OF VERTEBRAL BODY MARROW USED FOR COMBINED SOLID ORGAN AND BONE MARROW TRANSPLANTATION

PubMed Central

Rybka, Witold B.; Fontes, Paulo A.; Rao, Abdul S.; Winkelstein, Alan; Ricordi, Camillo; Ball, Edward D.; Starzl, Thomas E.

2010-01-01

While cadaveric vertebral bodies (VB) have long been proposed as a suitable source of bone marrow (BM) for transplantation (BMT), they have rarely been used for this purpose. We have infused VB BM immediately following whole organ (WO) transplantation to augment donor cell chimerism. We quantified the hematopoietic progenitor cell (HPC) content of VB BM as well as BM obtained from the iliac crests (IC) of normal allogeneic donors (ALLO) and from patients with malignancy undergoing autologous marrow harvest (AUTO). Patients undergoing WOIBM transplantation also had AUTO BM harvested in the event that subsequent lymphohematopoietic reconstitution was required. Twenty-four VB BM, 24 IC BM-ALLO, 31 IC AUTO, and 24 IC WO-AUTO were harvested. VB BM was tested 12 to 72 hr after procurement and infused after completion ofWO grafting. IC BM was tested and then used or cryopreserved immediately. HPC were quantified by clonal assay measuring CFU-GM, BFU-E, and CFU-GEMM, and by flow cytometry for CD34+ progenitor cells. On an average, 9 VB were processed during each harvest, and despite an extended processing time the number of viable nucleated cells obtained was significantly higher than that from IC. Furthermore, by HPC content, VB BM was equivalent to IC BM, which is routinely used for BMT. We conclude that VB BM is a clinically valuable source of BM for allogeneic transplantation. PMID:7701582

Magnetic-Nanoflocculant-Assisted Water-Nonpolar Solvent Interface Sieve for Microalgae Harvesting.

PubMed

Lee, Kyubock; Na, Jeong-Geol; Seo, Jung Yoon; Shim, Tae Soup; Kim, Bohwa; Praveenkumar, Ramasamy; Park, Ji-Yeon; Oh, You-Kwan; Jeon, Sang Goo

2015-08-26

Exploitation of magnetic flocculants is regarded as a very promising energy-saving approach to microalgae harvesting. However, its practical applicability remains limited, mainly because of the problem of the postharvest separation of magnetic flocculants from microalgal flocs, which is crucial both for magnetic-flocculant recycling and high-purity microalgal biomasses, but which is also a very challenging and energy-consuming step. In the present study, we designed magnetic nanoflocculants dually functionalizable by two different organosilane compounds, (3-aminopropyl)triethoxysilane (APTES) and octyltriethoxysilane (OTES), which flocculate negatively charged microalgae and are readily detachable at the water-nonpolar organic solvent (NOS) interface only by application of an external magnetic field. APTES functionalization imparts a positive zeta potential charge (29.6 mV) to magnetic nanoflocculants, thereby enabling microalgae flocculation with 98.5% harvesting efficiency (with a dosage of 1.6 g of dMNF/g of cells). OTES functionalization imparts lipophilicity to magnetic nanoflocculants to make them compatible with NOS, thus effecting efficient separation of magnetic flocculants passing through the water-NOS interface sieve from hydrophilic microalgae. Our new energy-saving approach to microalgae harvesting concentrates microalgal cultures (∼1.5 g/L) up to 60 g/L, which can be directly connected to the following process of NOS-assisted wet lipid extraction or biodiesel production, and therefore provides, by simplifying multiple downstream processes, a great potential cost reduction in microalgae-based biorefinement.

Synchronized energy and electron transfer processes in covalently linked CdSe-squaraine dye-TiO2 light harvesting assembly.

PubMed

Choi, Hyunbong; Santra, Pralay K; Kamat, Prashant V

2012-06-26

Manipulation of energy and electron transfer processes in a light harvesting assembly is an important criterion to mimic natural photosynthesis. We have now succeeded in sequentially assembling CdSe quantum dot (QD) and squaraine dye (SQSH) on TiO(2) film and couple energy and electron transfer processes to generate photocurrent in a hybrid solar cell. When attached separately, both CdSe QDs and SQSH inject electrons into TiO(2) under visible-near-IR irradiation. However, CdSe QD if linked to TiO(2) with SQSH linker participates in an energy transfer process. The hybrid solar cells prepared with squaraine dye as a linker between CdSe QD and TiO(2) exhibited power conversion efficiency of 3.65% and good stability during illumination with global AM 1.5 solar condition. Transient absorption spectroscopy measurements provided further insight into the energy transfer between excited CdSe QD and SQSH (rate constant of 6.7 × 10(10) s(-1)) and interfacial electron transfer between excited SQSH and TiO(2) (rate constant of 1.2 × 10(11) s(-1)). The synergy of covalently linked semiconductor quantum dots and near-IR absorbing squaraine dye provides new opportunities to harvest photons from selective regions of the solar spectrum in an efficient manner.

Electroactive polymers for gaining sea power

NASA Astrophysics Data System (ADS)

Scherber, Benedikt; Grauer, Matthias; Köllnberger, Andreas

2013-04-01

Target of this article will be the energy harvesting with dielectric elastomers for wave energy conversion. The main goal of this article is to introduce a new developed material profile enabling a specific amount of energy, making the harvesting process competitive against other existing offshore generation technologies. Electroactive polymers offer the chance to start with small wave energy converters to gain experiences and carry out a similar development as wind energy. Meanwhile there is a consortium being formed in Germany to develop such materials and processes for future products in this new business area. In order to demonstrate the applicability of the technological advancements, a scale demonstrator of a wave energy generator will be developed as well.

Adaptive harvest management of North American waterfowl populations: a brief history and future prospects

USGS Publications Warehouse

Nichols, J.D.; Runge, M.C.; Johnson, F.A.; Williams, B.K.

2007-01-01

Since 1995, the US Fish and Wildlife Service has used an adaptive approach to the management of sport harvest of mid-continent Mallard ducks (Anas platyrhynchos) in North America. This approach differs from many current approaches to conservation and management in requiring close collaboration between managers and scientists. Key elements of this process are objectives, alternative management actions, models permitting prediction of system responses, and a monitoring program. The iterative process produces optimal management decisions and leads to reduction in uncertainty about response of populations to management. This general approach to management has a number of desirable features and is recommended for use in many other programs of management and conservation.

Overview on the mechanisms of coffee germination and fermentation and their significance for coffee and coffee beverage quality.

PubMed

Waters, Deborah M; Arendt, Elke K; Moroni, Alice V

2017-01-22

Quality of coffee is a complex trait and is influenced by physical and sensory parameters. A complex succession of transformations during the processing of seeds to roasted coffee will inevitably influence the in-cup attributes of coffee. Germination and fermentation of the beans are two bioprocesses that take place during post-harvest treatment, and may lead to significant modifications of coffee attributes. The aim of this review is to address the current knowledge of dynamics of these two processes and their significance for bean modifications and coffee quality. The first part of this review gives an overview of coffee germination and its influence on coffee chemistry and quality. The germination process initiates while these non-orthodox seeds are still inside the cherry. This process is asynchronous and the evolution of germination depends on how the beans are processed. A range of metabolic reactions takes place during germination and can influence the carbohydrate, protein, and lipid composition of the beans. The second part of this review focuses on the microbiota associated with the beans during post-harvesting, exploring its effects on coffee quality and safety. The microbiota associated with the coffee cherries and beans comprise several bacterial, yeast, and fungal species and affects the processing from cherries to coffee beans. Indigenous bacteria and yeasts play a role in the degradation of pulp/mucilage, and their metabolism can affect the sensory attributes of coffee. On the other hand, the fungal population occurring during post-harvest and storage negatively affects coffee quality, especially regarding spoilage, off-tastes, and mycotoxin production.

Roll, Spin, Wash, or Filter? Processing of Lipoaspirate for Autologous Fat Grafting: An Updated, Evidence-Based Review of the Literature.

PubMed

Cleveland, Emily C; Albano, Nicholas J; Hazen, Alexes

2015-10-01

The use of autologous adipose tissue harvested through liposuction techniques for soft-tissue augmentation has become commonplace among cosmetic and reconstructive surgeons alike. Despite its longstanding use in the plastic surgery community, substantial controversy remains regarding the optimal method of processing harvested lipoaspirate before grafting. This evidence-based review builds on prior examinations of the literature to evaluate both established and novel methods for lipoaspirate processing. A comprehensive, systematic review of the literature was conducted using Ovid MEDLINE in January of 2015 to identify all relevant publications subsequent to the most recent review on this topic. Randomized controlled trials, clinical trials, and comparative studies comparing at least two of the following techniques were included: decanting, cotton gauze (Telfa) rolling, centrifugation, washing, filtration, and stromal vascular fraction isolation. Nine articles comparing various methods of processing human fat for autologous grafting were selected based on inclusion and exclusion criteria. Five compared established processing techniques (i.e., decanting, cotton gauze rolling, centrifugation, and washing) and four publications evaluated newer proprietary technologies, including washing, filtration, and/or methods to isolate stromal vascular fraction. The authors failed to find compelling evidence to advocate a single technique as the superior method for processing lipoaspirate in preparation for autologous fat grafting. A paucity of high-quality data continues to limit the clinician's ability to determine the optimal method for purifying harvested adipose tissue. Novel automated technologies hold promise, particularly for large-volume fat grafting; however, extensive additional research is required to understand their true utility and efficiency in clinical settings.

Micro-scale piezoelectric vibration energy harvesting: From fixed-frequency to adaptable-frequency devices

NASA Astrophysics Data System (ADS)

Miller, Lindsay Margaret

Wireless sensor networks (WSNs) have the potential to transform engineering infrastructure, manufacturing, and building controls by allowing condition monitoring, asset tracking, demand response, and other intelligent feedback systems. A wireless sensor node consists of a power supply, sensor(s), power conditioning circuitry, radio transmitter and/or receiver, and a micro controller. Such sensor nodes are used for collecting and communicating data regarding the state of a machine, system, or process. The increasing demand for better ways to power wireless devices and increase operation time on a single battery charge drives an interest in energy harvesting research. Today, wireless sensor nodes are typically powered by a standard single-charge battery, which becomes depleted within a relatively short timeframe depending on the application. This introduces tremendous labor costs associated with battery replacement, especially when there are thousands of nodes in a network, the nodes are remotely located, or widely-distributed. Piezoelectric vibration energy harvesting presents a potential solution to the problems associated with too-short battery life and high maintenance requirements, especially in industrial environments where vibrations are ubiquitous. Energy harvester designs typically use the harvester to trickle charge a rechargeable energy storage device rather than directly powering the electronics with the harvested energy. This allows a buffer between the energy harvester supply and the load where energy can be stored in a "tank". Therefore, the harvester does not need to produce the full required power at every instant to successfully power the node. In general, there are tens of microwatts of power available to be harvested from ambient vibrations using micro scale devices and tens of milliwatts available from ambient vibrations using meso scale devices. Given that the power requirements of wireless sensor nodes range from several microwatts to about one hundred milliwatts and are falling steadily as improvements are made, it is feasible to use energy harvesting to power WSNs. This research begins by presenting the results of a thorough survey of ambient vibrations in the machine room of a large campus building, which found that ambient vibrations are low frequency, low amplitude, time varying, and multi-frequency. The modeling and design of fixed-frequency micro scale energy harvesters are then presented. The model is able to take into account rotational inertia of the harvester's proof mass and it accepts arbitrary measured acceleration input, calculating the energy harvester's voltage as an output. The fabrication of the micro electromechanical system (MEMS) energy harvesters is discussed and results of the devices harvesting energy from ambient vibrations are presented. The harvesters had resonance frequencies ranging from 31 - 232 Hz, which was the lowest reported in literature for a MEMS device, and produced 24 pW/g2 - 10 nW/g2 of harvested power from ambient vibrations. A novel method for frequency modification of the released harvester devices using a dispenser printed mass is then presented, demonstrating a frequency shift of 20 Hz. Optimization of the MEMS energy harvester connected to a resistive load is then presented, finding that the harvested power output can be increased to several microwatts with the optimized design as long as the driving frequency matches the harvester's resonance frequency. A framework is then presented to allow a similar optimization to be conducted with the harvester connected to a synchronously switched pre-bias circuit. With the realization that the optimized energy harvester only produces usable amounts of power if the resonance frequency and driving frequency match, which is an unrealistic situation in the case of ambient vibrations which change over time and are not always known a priori, an adaptable-frequency energy harvester was designed. The adaptable-frequency harvester works by taking advantage of the coupling between a sliding mass and a beam. The derivation of the nonlinear coupled dynamic mathematical model representing the physical system is presented, as are the numerical and experimental results of the prototype device. Passive self-tuning was observed in this system and the mathematical model was found to successfully portray the physical behavior.

Potential Dimension Yields From Direct Processing

Treesearch

Wenjie Lin; D. Earl Kline; Philip A. Araman

1994-01-01

As the price of timber increases and environmental leigslation limits harvestable log volumes, the process of converting logs directly into dimension parts needs further exploration. Direct processing converts logs directly into rough green dimension parts without the intermediate steps of lumber manufacturing, grading, trading, shipping and drying. A major attraction...

Infrared pre-drying and dry-dehulling of walnuts for improved processing efficiency and product quality

USDA-ARS?s Scientific Manuscript database

The walnut industry is faced with an urgent need to improve post-harvest processing efficiency, particularly drying and dehulling operations. This research investigated the feasibility of dry-dehulling and infrared (IR) pre-drying of walnuts for improved processing efficiency and dried product quali...

Electromechanical conversion efficiency for dielectric elastomer generator in different energy harvesting cycles

NASA Astrophysics Data System (ADS)

Cao, Jian-Bo; E, Shi-Ju; Guo, Zhuang; Gao, Zhao; Luo, Han-Pin

2017-11-01

In order to improve electromechanical conversion efficiency for dielectric elastomer generators (DEG), on the base of studying DEG energy harvesting cycles of constant voltage, constant charge and constant electric field intensity, a new combined cycle mode and optimization theory in terms of the generating mechanism and electromechanical coupling process have been built. By controlling the switching point to achieve the best energy conversion cycle, the energy loss in the energy conversion process is reduced. DEG generating test bench which was used to carry out comparative experiments has been established. Experimental results show that the collected energy in constant voltage cycle, constant charge cycle and constant electric field intensity energy harvesting cycle decreases in turn. Due to the factors such as internal resistance losses, electrical losses and so on, actual energy values are less than the theoretical values. The electric energy conversion efficiency by combining constant electric field intensity cycle with constant charge cycle is larger than that of constant electric field intensity cycle. The relevant conclusions provide a basis for the further applications of DEG.

Extending the NIF DISCO framework to automate complex workflow: coordinating the harvest and integration of data from diverse neuroscience information resources

PubMed Central

Marenco, Luis N.; Wang, Rixin; Bandrowski, Anita E.; Grethe, Jeffrey S.; Shepherd, Gordon M.; Miller, Perry L.

2014-01-01

This paper describes how DISCO, the data aggregator that supports the Neuroscience Information Framework (NIF), has been extended to play a central role in automating the complex workflow required to support and coordinate the NIF’s data integration capabilities. The NIF is an NIH Neuroscience Blueprint initiative designed to help researchers access the wealth of data related to the neurosciences available via the Internet. A central component is the NIF Federation, a searchable database that currently contains data from 231 data and information resources regularly harvested, updated, and warehoused in the DISCO system. In the past several years, DISCO has greatly extended its functionality and has evolved to play a central role in automating the complex, ongoing process of harvesting, validating, integrating, and displaying neuroscience data from a growing set of participating resources. This paper provides an overview of DISCO’s current capabilities and discusses a number of the challenges and future directions related to the process of coordinating the integration of neuroscience data within the NIF Federation. PMID:25018728

Polaron effects on the performance of light-harvesting systems: a quantum heat engine perspective

NASA Astrophysics Data System (ADS)

Xu, Dazhi; Wang, Chen; Zhao, Yang; Cao, Jianshu

2016-02-01

We explore energy transfer in a generic three-level system, which is coupled to three non-equilibrium baths. Built on the concept of quantum heat engine, our three-level model describes non-equilibrium quantum processes including light-harvesting energy transfer, nano-scale heat transfer, photo-induced isomerization, and photovoltaics in double quantum-dots. In the context of light-harvesting, the excitation energy is first pumped up by sunlight, then is transferred via two excited states which are coupled to a phonon bath, and finally decays to the reaction center. The efficiency of this process is evaluated by steady state analysis via a polaron-transformed master equation; thus the entire range of the system-phonon coupling strength can be covered. We show that the coupling with the phonon bath not only modifies the steady state, resulting in population inversion, but also introduces a finite steady state coherence which optimizes the energy transfer flux and efficiency. In the strong coupling limit, the steady state coherence disappears and the efficiency recovers the heat engine limit given by Scovil and Schultz-Dubois (1959 Phys. Rev. Lett. 2 262).

Effective harvesting of microalgae by coagulation–flotation

PubMed Central

Xia, Ling; Li, Yinta; Huang, Rong

2017-01-01

This study developed a coagulation–flotation process for microalgae Chlorella sp. XJ-445 harvesting, which was composed of algal surface modification by combined use of Al3+ and cetyltrimethylammonium bromide (CTAB) and followed dispersed bubble flotation. Dissolved organic matter (DOM) in the medium was firstly characterized and mainly consisted of hydrophilic low molecular weight molecules. The dosage of collector (CTAB) and coagulant (Al3+) were optimized, and with the pretreatment of 40 mg Al3+ and 60 mg CTAB per 1 g dry biomass without pH adjustment, a maximum flotation recovery efficiency of 98.73% can be achieved with the presence of DOM. Algal cells characterization results showed that the combined use of CTAB and Al3+ largely enhanced the algal floc size, and exhibited higher degree of hydrophobicity, which favoured the flotation, and can be interpreted by DLVO (Derjaguin, Landau, Verwey and Overbeek) modelling. A benefit in fatty acid conversion was further found with the optimized coagulation–flotation process. It was suggested that this coagulation based flotation is a promising strategy for high-efficiency harvesting of microalgae. PMID:29291079

Extending the NIF DISCO framework to automate complex workflow: coordinating the harvest and integration of data from diverse neuroscience information resources.

PubMed

Marenco, Luis N; Wang, Rixin; Bandrowski, Anita E; Grethe, Jeffrey S; Shepherd, Gordon M; Miller, Perry L

2014-01-01

This paper describes how DISCO, the data aggregator that supports the Neuroscience Information Framework (NIF), has been extended to play a central role in automating the complex workflow required to support and coordinate the NIF's data integration capabilities. The NIF is an NIH Neuroscience Blueprint initiative designed to help researchers access the wealth of data related to the neurosciences available via the Internet. A central component is the NIF Federation, a searchable database that currently contains data from 231 data and information resources regularly harvested, updated, and warehoused in the DISCO system. In the past several years, DISCO has greatly extended its functionality and has evolved to play a central role in automating the complex, ongoing process of harvesting, validating, integrating, and displaying neuroscience data from a growing set of participating resources. This paper provides an overview of DISCO's current capabilities and discusses a number of the challenges and future directions related to the process of coordinating the integration of neuroscience data within the NIF Federation.

The effect of sea-water and fresh-water soaking on the hedonic test of Eucheuma sp. syrup and pudding

NASA Astrophysics Data System (ADS)

Novianty, H.; Herandarudewi, S. M. C.

2018-04-01

Seaweed is a non-fishery marine commodity that has great opportunities to be developed in Indonesia. One of the seaweed with a high economic value is Eucheuma alvarezii. This seaweed can be used as an additional material in cosmetic and pharmaceutical products or directly used for syrup and pudding. Post-harvest technique conducted by the seaweed farmers will affects the quality of dried and processed products. The purpose of this study is to see the effect of post harvest technique on the quality of dried seaweed and hedonic test (favorable test) of processed product (syrup and pudding). This study was conducted using descriptive method. The study compared dried, syrup, and puddings from two differents post-harvest technique, between salt and fresh-water draining products. The results showed that fresh-water draining technique obtained better quality results organoleptic test. Supported by hedonic test, that showed more panelists were prefered the fresh-water drained products of syrup and pudding. The preference were much higher for the fresh-water drained products in all three catagories of color, taste, and smell.

Noise exposure and hearing conservation for farmers of rural Japanese communities

NASA Astrophysics Data System (ADS)

Miyakita, Takashi; Ueda, Atsushi; Futatsuka, Makoto; Inaoka, Tsukasa; Nagano, Megumi; Koyama, Wasaku

2004-10-01

Agricultural mechanization in Japan has progressed dramatically since 1955 with the introduction of tractors, harvesters, and processing machines. These technological developments have resulted in an increase in exposure to sources of noise that are not only annoying, but damaging to hearing. The present study was undertaken to determine, whether Japanese farmers are at risk for noise-induced hearing loss in comparison with office workers, and by evaluating the present conditions regarding occupational noise levels among agricultural workers. The results suggest that farmers, especially male farmers, have a high prevalence of hearing loss in the higher frequency ranges. Daily noise exposure levels in L ranged from 81.5 to 99.1 dBA for tea harvesting and processing, and from 83.2 to 97.6 for sugar cane harvesting. Taking into account their rather long working hours and excessive noise from farm machinery, it is concluded that farmers are at risk for noise-induced hearing loss. These findings clearly indicate a strong need for implementation of hearing conservation programs among agricultural workers exposed to machinery noise.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Rittmann, Bruce; Krajmalnik‐Brown, Rosa; Zevin, Alexander

The grandest challenge facing human society today is providing large amounts of energy and industrial chemicals that are renewable and carbon-neutral. An outstanding opportunity lies in employing photosynthetic microorganisms, which have the potential to generate energy and chemical feedstock from sunlight and CO 2 at rates 10 to 100 times greater than plants. Major challenges for solar-powered production using photosynthetic microorganisms are associated with the harvesting and downstream processing of biomass to yield the usable energy or material feedstock e.g. The technical challenges and costs of downstream processing could be avoided if, powered by solar energy, the photosynthetic microorganisms weremore » to convert CO 2 directly to the desired product, which they release for direct harvesting. This approach creates a true photosynthetic factory, our goal for Photosynthetic Factory Direct! Our team is able to genetically modify the cyanobacterium Synechocystis sp. PCC 6803 so that it produces and excretes a range of renewable energy and chemical products directly from CO 2 and sunlight. Essential to realizing the potential of the photosynthetic factory is an engineered Advanced Photobioreactor (APBR) for reliable synthesis and harvest of the products.« less

Enhancing the absorption and energy transfer process via quantum entanglement

NASA Astrophysics Data System (ADS)

Zong, Xiao-Lan; Song, Wei; Zhou, Jian; Yang, Ming; Yu, Long-Bao; Cao, Zhuo-Liang

2018-07-01

The quantum network model is widely used to describe the dynamics of excitation energy transfer in photosynthesis complexes. Different from the previous schemes, we explore a specific network model, which includes both light-harvesting and energy transfer process. Here, we define a rescaled measure to manifest the energy transfer efficiency from external driving to the sink, and the external driving fields are used to simulate the energy absorption process. To study the role of initial state in the light-harvesting and energy transfer process, we assume the initial state of the donors to be two-qubit and three-qubit entangled states, respectively. In the two-qubit initial state case, we find that the initial entanglement between the donors can help to improve the absorption and energy transfer process for both the near-resonant and large-detuning cases. For the case of three-qubit initial state, we can see that the transfer efficiency will reach a larger value faster in the tripartite entanglement case compared to the bipartite entanglement case.

Combined Effects of Irrigation Regime, Genotype, and Harvest Stage Determine Tomato Fruit Quality and Aptitude for Processing into Puree.

PubMed

Arbex de Castro Vilas Boas, Alexandre; Page, David; Giovinazzo, Robert; Bertin, Nadia; Fanciullino, Anne-Laure

2017-01-01

Industry tomatoes are produced under a range of climatic conditions and practices which significantly impact on main quality traits of harvested fruits. However, the quality of tomato intended for processing is currently addressed on delivery through color and Brix only, whereas other traits are overlooked. Very few works provided an integrated view of the management of tomato puree quality throughout the chain. To gain insights into pre- and post-harvest interactions, four genotypes, two water regimes, three maturity stages, and two processes were investigated. Field and glasshouse experiments were conducted near Avignon, France, from May to August 2016. Two irrigation regimes were applied: control plants were irrigated in order to match 100% of evapotranspiration (ETP); water deficit (WD) plants were irrigated as control plants until anthesis of the first flowers, then irrigation was reduced to 60 and 50% ETP in field, and glasshouse respectively. Fruits were collected at three stages during ripening. Their color, fresh weight, dry matter content, and metabolite contents were determined before processing. Pericarp cell size was evaluated in glasshouse only. Two laboratory-scaled processing methods were applied before structural and biochemical analyses of the purees. Results outlined interactive effects between crop and process management. WD hardly reduced yield, but increased dry matter content in the field, in contrast to the glasshouse. The puree viscosity strongly depended on the genotype and the maturity stage, but it was disconnected from fruit dry matter content or Brix. The process impact on puree viscosity strongly depended on water supply during fruit production. Moreover, the lycopene content of fresh fruit may influence puree viscosity. This work opens new perspectives for managing puree quality in the field showing that it was possible to reduce water supply without affecting yield and to improve puree quality.

Fast and scalable purification of a therapeutic full-length antibody based on process crystallization.

PubMed

Smejkal, Benjamin; Agrawal, Neeraj J; Helk, Bernhard; Schulz, Henk; Giffard, Marion; Mechelke, Matthias; Ortner, Franziska; Heckmeier, Philipp; Trout, Bernhardt L; Hekmat, Dariusch

2013-09-01

The potential of process crystallization for purification of a therapeutic monoclonal IgG1 antibody was studied. The purified antibody was crystallized in non-agitated micro-batch experiments for the first time. A direct crystallization from clarified CHO cell culture harvest was inhibited by high salt concentrations. The salt concentration of the harvest was reduced by a simple pretreatment step. The crystallization process from pretreated harvest was successfully transferred to stirred tanks and scaled-up from the mL-scale to the 1 L-scale for the first time. The crystallization yield after 24 h was 88-90%. A high purity of 98.5% was reached after a single recrystallization step. A 17-fold host cell protein reduction was achieved and DNA content was reduced below the detection limit. High biological activity of the therapeutic antibody was maintained during the crystallization, dissolving, and recrystallization steps. Crystallization was also performed with impure solutions from intermediate steps of a standard monoclonal antibody purification process. It was shown that process crystallization has a strong potential to replace Protein A chromatography. Fast dissolution of the crystals was possible. Furthermore, it was shown that crystallization can be used as a concentrating step and can replace several ultra-/diafiltration steps. Molecular modeling suggested that a negative electrostatic region with interspersed exposed hydrophobic residues on the Fv domain of this antibody is responsible for the high crystallization propensity. As a result, process crystallization, following the identification of highly crystallizable antibodies using molecular modeling tools, can be recognized as an efficient, scalable, fast, and inexpensive alternative to key steps of a standard purification process for therapeutic antibodies. Copyright © 2013 Wiley Periodicals, Inc.

Physical and hydrological properties of the soil after Pine harvesting in Maule, Chile

NASA Astrophysics Data System (ADS)

Fernández Raga, María; Fuentes Espoz, Juan Pablo

2014-05-01

The south of Chile has been under great pressure for about 150 years, with the replacement of native forests by agricultural crops and subsequently by plantations with fast-growing exotic species. Historically, it was considered that these plantations have stopped the degradation process of the ground. However, the restoration of the soil system can be considered as very limited or even null because of three reasons: the rotations of these artificial forest systems are too short (just 25 years ), the chosen areas are already degraded land, and after the harvesting it is common to get fire to clean. The objective of this research was to evaluate current forest management practices of these forest systems to make them more sustainable, mainly studying the effect of harvesting and waste management planting some physical - hydrological properties of the soil. This research was done in "Las Brisas", a degraded soil characterized by different planting practices of forest species, which have been harvested and, after that, burnt for taking out the residual waste. The study tried to determine the variations in the water content of the soil after fire at different depths, obtaining moisture profiles that reflect the change in soil moisture while simulating rain occurs. temperature of the fire. Several samples were taken and divided into four different experiments of management practices: some of them were dry, others were burnt, others suffered both processes and the last no process at all. Some analysis were done to determine the behavior of the main hydrological properties (ie particle size distribution, aggregate stability , hydrophobicity , infiltration ). The information collected was analyzed by the hydrologic model Hydrus -2D, to fully assess the impact of the extraction of the forest from a highly sensitive system erosive phenomena. The information obtained will be published.

Methods of downstream processing for the production of biodiesel from microalgae.

PubMed

Kim, Jungmin; Yoo, Gursong; Lee, Hansol; Lim, Juntaek; Kim, Kyochan; Kim, Chul Woong; Park, Min S; Yang, Ji-Won

2013-11-01

Despite receiving increasing attention during the last few decades, the production of microalgal biofuels is not yet sufficiently cost-effective to compete with that of petroleum-based conventional fuels. Among the steps required for the production of microalgal biofuels, the harvest of the microalgal biomass and the extraction of lipids from microalgae are two of the most expensive. In this review article, we surveyed a substantial amount of previous work in microalgal harvesting and lipid extraction to highlight recent progress in these areas. We also discuss new developments in the biodiesel conversion technology due to the importance of the connectivity of this step with the lipid extraction process. Furthermore, we propose possible future directions for technological or process improvements that will directly affect the final production costs of microalgal biomass-based biofuels. Copyright © 2013 Elsevier Inc. All rights reserved.

Artificial muscles on heat

NASA Astrophysics Data System (ADS)

McKay, Thomas G.; Shin, Dong Ki; Percy, Steven; Knight, Chris; McGarry, Scott; Anderson, Iain A.

2014-03-01

Many devices and processes produce low grade waste heat. Some of these include combustion engines, electrical circuits, biological processes and industrial processes. To harvest this heat energy thermoelectric devices, using the Seebeck effect, are commonly used. However, these devices have limitations in efficiency, and usable voltage. This paper investigates the viability of a Stirling engine coupled to an artificial muscle energy harvester to efficiently convert heat energy into electrical energy. The results present the testing of the prototype generator which produced 200 μW when operating at 75°C. Pathways for improved performance are discussed which include optimising the electronic control of the artificial muscle, adjusting the mechanical properties of the artificial muscle to work optimally with the remainder of the system, good sealing, and tuning the resonance of the displacer to minimise the power required to drive it.

Oregon’s forest products industry and timber harvest, 2008: industry trends and impacts of the Great Recession through 2010

Treesearch

Charles B. Gale; Charles E. Keegan; Erik C. Berg; Jean Daniels; Glenn A. Christensen; Colin B. Sorenson; Todd A. Morgan; Paul Polzin

2012-01-01

This report traces the flow of Oregon’s 2008 timber harvest through the primary timber processing industry and provides a description of the structure, operation, and condition of Oregon’s forest products industry as a whole. It is the second in a series of reports that update the status of the industry every 5 years. Based on a census conducted in 2009 and 2010, we...

Veg-03 Ground Harvest

NASA Image and Video Library

2016-12-05

Inside the Veggie flight laboratory in the Space Station Processing Facility at NASA’s Kennedy Space Center in Florida, a research scientist harvests a portion of the 'Outredgeous' red romaine lettuce from the Veg-03 ground control unit. The purpose of the ground Veggie system is to provide a control group to compare against the lettuce grown in orbit on the International Space Station. Veg-03 will continue NASA’s deep space plant growth research to benefit the Earth and the agency’s journey to Mars.

The Role of Shewanella oneidensis MR-1 Outer Surface Structures in Extracellular Electron Transfer

DTIC Science & Technology

2010-01-01

Supernatants from the wells of the air-exposed VBSA that had been in operation for 220 h were harvested and planktonic cells were removed via...prepilins. In some bacteria, such as Pseudomonas aerugino- sa and Vibrio cholerae, PilD plays a dual role and processes type IVand T2SS prepilins [38 – 41... harvested from the VBSA at the times indicated by arrows in Fig. 4 (100 h data not shown). Fig. 6. Presence of riboflavin in cell-free supernatants

Remedial Investigation Report. Volume 6: Southern Study Area, Sections 1.0, 2.0, and 3.0 Text, Version 3.3

DTIC Science & Technology

1989-06-01

plains harvest mice, western harvest mice, northern grasshopper mice, prairie voles, meadow voles, Ord’s kangaroo rats, hispid pocket mice, and...both metabolically and from a manufacturing perspective. DDT and DDE are two of the more persistent OCPs (Edwards, 1972). This may be due in part to...DBPC, although toxic, does not bioaccumulate significantly, while isodrin, an analog of endrin, is converted to endrin by metabolic processes. Two

The rectenna design on contact lens for wireless powering of the active intraocular pressure monitoring system.

PubMed

Cheng, H W; Jeng, B M; Chen, C Y; Huang, H Y; Chiou, J C; Luo, C H

2013-01-01

This paper proposed a wireless power harvesting system with micro-electro-mechanical-systems (MEMS) fabrication for noninvasive intraocular pressure (IOP) measurement on soft contact lens substructure. The power harvesting IC consists of a loop antenna, an impedance matching network and a rectifier. The proposed IC has been designed and fabricated by CMOS 0.18 um process that operates at the ISM band of 5.8 GHz. The antenna and the power harvesting IC would be bonded together by using flip chip bonding technologies without extra wire interference. The circuit utilized an impedance transformation circuit to boost the input RF signal that improves the circuit performance. The proposed design achieves an RF-to-DC conversion efficiency of 35% at 5.8 GHz.

Advanced Plant Habitat Test Harvest

NASA Image and Video Library

2017-08-24

John "JC" Carver, a payload integration engineer with NASA Kennedy Space Center's Test and Operations Support Contract, uses a FluorPen to measure the chlorophyll fluorescence of Arabidopsis thaliana plants inside the growth chamber of the Advanced Plant Habitat (APH) Flight Unit No. 1. Half the plants were then harvested. The harvest is part of an ongoing verification test of the APH unit, which is located inside the International Space Station Environmental Simulator in Kennedy's Space Station Processing Facility. The APH undergoing testing at Kennedy is identical to one on the station and uses red, green and broad-spectrum white LED lights to grow plants in an environmentally controlled chamber. The seeds grown during the verification test will be grown on the station to help scientists understand how these plants adapt to spaceflight.

Conjugated Polymers for Flexible Energy Harvesting and Storage.

PubMed

Zhang, Zhitao; Liao, Meng; Lou, Huiqing; Hu, Yajie; Sun, Xuemei; Peng, Huisheng

2018-03-01

Since the discovery of conjugated polymers in the 1970s, they have attracted considerable interest in light of their advantages of having a tunable bandgap, high electroactivity, high flexibility, and good processability compared to inorganic conducting materials. The above combined advantages make them promising for effective energy harvesting and storage, which have been widely studied in recent decades. Herein, the key advancements in the use of conjugated polymers for flexible energy harvesting and storage are reviewed. The synthesis, structure, and properties of conjugated polymers are first summarized. Then, their applications in flexible polymer solar cells, thermoelectric generators, supercapacitors, and lithium-ion batteries are described. The remaining challenges are then discussed to highlight the future direction in the development of conjugated polymers. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Principles of thermoacoustic energy harvesting

NASA Astrophysics Data System (ADS)

Avent, A. W.; Bowen, C. R.

2015-11-01

Thermoacoustics exploit a temperature gradient to produce powerful acoustic pressure waves. The technology has a key role to play in energy harvesting systems. A time-line in the development of thermoacoustics is presented from its earliest recorded example in glass blowing through to the development of the Sondhauss and Rijke tubes to Stirling engines and pulse-tube cryo-cooling. The review sets the current literature in context, identifies key publications and promising areas of research. The fundamental principles of thermoacoustic phenomena are explained; design challenges and factors influencing efficiency are explored. Thermoacoustic processes involve complex multi-physical coupling and transient, highly non-linear relationships which are computationally expensive to model; appropriate numerical modelling techniques and options for analyses are presented. Potential methods of harvesting the energy in the acoustic waves are also examined.

Harvesting of freshwater microalgae biomass by Scenedesmus sp. as bioflocculant

NASA Astrophysics Data System (ADS)

Rinanti, A.; Purwadi, R.

2018-01-01

This study is particularly expected to provide information on the diversity of microalgae as the flocculant agent that gives the highest biomass yield. Bioflocculation was done by using one of the flocculating microalgae i.e. Scenedesmus obliquus to concentrate on non-flocculating microalgae Chlorella vulgaris. The freshwater microalgae S. obliquus tested it ability to harvest other non-flocculating microalgae, increased sedimentation rate in the flocculation process and increased biomass yield. The flocculation of biomass microalgae with chemical flocculant as comparison was done by adding alum (K2SO4·Al2 (SO4)3·24H2O). The addition of alum (K2SO4·Al2 (SO4)3·24H2O) as flocculant at pH 11 and S. obliquus sp. as bioflocculant caused significant alteration of nutrition of microalgae. Overall, the essential content produced by flocculation method with addition of alum or with bioflocculation (%, mg/100 mg dry weight) are lipid 31,64; 38,69, protein 30,79; 38.50%, and chlorophyll 0.6253; 0.8420). Harvesting with bioflocculation methods conducted at the end of the cultivation period increase the amount of biomass significantly and can accelerate the settling time of biomass. Harvesting microalgae cells by bioflocculation method becomes an economically competitive harvesting method compared to alum as a chemical flocculant because of the cheaper cost of flocculant, not toxic so it does not require further water treatment after harvesting due to the use of alum as chemical flocculants.

Evaluating vehicular-induced bridge vibrations for energy harvesting applications

NASA Astrophysics Data System (ADS)

Reichenbach, Matthew; Fasl, Jeremiah; Samaras, Vasilis A.; Wood, Sharon; Helwig, Todd; Lindenberg, Richard

2012-04-01

Highway bridges are vital links in the transportation network in the United States. Identifying possible safety problems in the approximately 600,000 bridges across the country is generally accomplished through labor-intensive, visual inspections. Ongoing research sponsored by NIST seeks to improve inspection practices by providing real-time, continuous monitoring technology for steel bridges. A wireless sensor network with a service life of ten years that is powered by an integrated energy harvester is targeted. In order to achieve the target ten-year life for the monitoring system, novel approaches to energy harvesting for use in recharging batteries are investigated. Three main sources of energy are evaluated: (a) vibrational energy, (b) solar energy, and (c) wind energy. Assessing the energy produced from vehicular-induced vibrations and converted through electromagnetic induction is the focus of this paper. The goal of the study is to process acceleration data and analyze the vibrational response of steel bridges to moving truck loads. Through spectral analysis and harvester modeling, the feasibility of vibration-based energy harvesting for longterm monitoring can be assessed. The effects of bridge conditions, ambient temperature, truck traffic patterns, and harvester position on the power content of the vibrations are investigated. With sensor nodes continually recharged, the proposed real-time monitoring system will operate off the power grid, thus reducing life cycle costs and enhancing inspection practices for state DOTs. This paper will present the results of estimating the vibration energy of a steel bridge in Texas.

Acquiring geographical data with web harvesting

NASA Astrophysics Data System (ADS)

Dramowicz, K.

2016-04-01

Many websites contain very attractive and up to date geographical information. This information can be extracted, stored, analyzed and mapped using web harvesting techniques. Poorly organized data from websites are transformed with web harvesting into a more structured format, which can be stored in a database and analyzed. Almost 25% of web traffic is related to web harvesting, mostly while using search engines. This paper presents how to harvest geographic information from web documents using the free tool called the Beautiful Soup, one of the most commonly used Python libraries for pulling data from HTML and XML files. It is a relatively easy task to process one static HTML table. The more challenging task is to extract and save information from tables located in multiple and poorly organized websites. Legal and ethical aspects of web harvesting are discussed as well. The paper demonstrates two case studies. The first one shows how to extract various types of information about the Good Country Index from the multiple web pages, load it into one attribute table and map the results. The second case study shows how script tools and GIS can be used to extract information from one hundred thirty six websites about Nova Scotia wines. In a little more than three minutes a database containing one hundred and six liquor stores selling these wines is created. Then the availability and spatial distribution of various types of wines (by grape types, by wineries, and by liquor stores) are mapped and analyzed.

An Energy Aware Adaptive Sampling Algorithm for Energy Harvesting WSN with Energy Hungry Sensors.

PubMed

Srbinovski, Bruno; Magno, Michele; Edwards-Murphy, Fiona; Pakrashi, Vikram; Popovici, Emanuel

2016-03-28

Wireless sensor nodes have a limited power budget, though they are often expected to be functional in the field once deployed for extended periods of time. Therefore, minimization of energy consumption and energy harvesting technology in Wireless Sensor Networks (WSN) are key tools for maximizing network lifetime, and achieving self-sustainability. This paper proposes an energy aware Adaptive Sampling Algorithm (ASA) for WSN with power hungry sensors and harvesting capabilities, an energy management technique that can be implemented on any WSN platform with enough processing power to execute the proposed algorithm. An existing state-of-the-art ASA developed for wireless sensor networks with power hungry sensors is optimized and enhanced to adapt the sampling frequency according to the available energy of the node. The proposed algorithm is evaluated using two in-field testbeds that are supplied by two different energy harvesting sources (solar and wind). Simulation and comparison between the state-of-the-art ASA and the proposed energy aware ASA (EASA) in terms of energy durability are carried out using in-field measured harvested energy (using both wind and solar sources) and power hungry sensors (ultrasonic wind sensor and gas sensors). The simulation results demonstrate that using ASA in combination with an energy aware function on the nodes can drastically increase the lifetime of a WSN node and enable self-sustainability. In fact, the proposed EASA in conjunction with energy harvesting capability can lead towards perpetual WSN operation and significantly outperform the state-of-the-art ASA.

Effect of variety and harvest date on nutritive value and ruminal degradability of ensiled maize ears.

PubMed

Terler, Georg; Gruber, Leonhard; Knaus, Wilhelm Friedrich

2017-10-01

The nutritive value of whole crop forage maize is influenced by the proportion of ears and stover in the whole crop and by the nutrient composition and digestibility characteristics of the plant parts. An experiment investigating the impact of variety, harvest date and year on the nutritive value of ensiled maize ears was carried out in three consecutive years (2007, 2008 and 2010). Nine different maize varieties were harvested at three different maturity stages (50, 55 and 60% dry matter (DM) content in the ears). After harvest, ears and stover were ensiled separately and afterwards nutrient composition and ruminal nutrient degradability (organic matter (OM), crude protein (CP) and non-fibre carbohydrates (NFC)) were analysed. Variety had a significant influence on content of CP and effective ruminal degradability (ED) of OM at low passage rates, whereas ED of CP and NFC was not affected by variety. In contrast, harvest date and year significantly influenced nutrient composition and ruminal degradability of ensiled maize ears. The content of NFC increased and the content of fibre components as well as ED of OM, CP and NFC declined with processing maturity of the maize plants. At a passage rate of 5% h -1 , ED of OM declined from 75.9% to 68.4%, ED of CP from 82.5% to 73.8% and ED of NFC from 88.0% to 82.3% between the early and late harvest date. The results of this study indicate that the nutrient composition and ruminal degradability of ensiled maize ears are affected mainly by maturity stage at harvest and by year, whereas variety has only little influence.

Accounting for Forest Harvest and Wildfire in a Spatially-distributed Carbon Cycle Process Model

NASA Astrophysics Data System (ADS)

Turner, D. P.; Ritts, W.; Kennedy, R. E.; Yang, Z.; Law, B. E.

2009-12-01

Forests are subject to natural disturbances in the form of wildfire, as well as management-related disturbances in the form of timber harvest. These disturbance events have strong impacts on local and regional carbon budgets, but quantifying the associated carbon fluxes remains challenging. The ORCA Project aims to quantify regional net ecosystem production (NEP) and net biome production (NBP) in Oregon, California, and Washington, and we have adopted an integrated approach based on Landsat imagery and ecosystem modeling. To account for stand-level carbon fluxes, the Biome-BGC model has been adapted to simulate multiple severities of fire and harvest. New variables include snags, direct fire emissions, and harvest removals. New parameters include fire-intensity-specific combustion factors for each carbon pool (based on field measurements) and proportional removal rates for harvest events. To quantify regional fluxes, the model is applied in a spatially-distributed mode over the domain of interest, with disturbance history derived from a time series of Landsat images. In stand-level simulations, the post disturbance transition from negative (source) to positive (sink) NEP is delayed approximately a decade in the case of high severity fire compared to harvest. Simulated direct pyrogenic emissions range from 11 to 25 % of total non-soil ecosystem carbon. In spatial mode application over Oregon and California, the sum of annual pyrogenic emissions and harvest removals was generally less that half of total NEP, resulting in significant carbon sequestration on the land base. Spatially and temporally explicit simulation of disturbance-related carbon fluxes will contribute to our ability to evaluate effects of management on regional carbon flux, and in our ability to assess potential biospheric feedbacks to climate change mediated by changing disturbance regimes.

Continuity and change in subsistence harvests in five Bering Sea communities: Akutan, Emmonak, Savoonga, St. Paul, and Togiak

NASA Astrophysics Data System (ADS)

Fall, James A.; Braem, Nicole S.; Brown, Caroline L.; Hutchinson-Scarbrough, Lisa B.; Koster, David S.; Krieg, Theodore M.

2013-10-01

To document and quantify subsistence harvests of fish and wildlife resources, and provide topics for subsequent key respondent interviews to collect local and traditional knowledge (LTK) about the Bering Sea ecosystem, comprehensive household harvest surveys were conducted in four Bering Sea Alaska Native communities: Akutan, Emmonak, Savoonga, and Togiak. In a fifth community, St. Paul, annual programs to document two key subsistence resources, fur seals and sea lions, continued. Surveys documented relatively high and diverse subsistence harvests, consistent with earlier research that demonstrated the continuing economic, social, and cultural importance of subsistence uses of wild resources. The research also found differences in subsistence use patterns compared to previous years' studies, such as harvest levels, harvest composition, and diversity of resources used, although differences between study years were not uniform across communities. Survey respondents, as well as key respondents in subsequent interviews, identified a complex range of personal, economic, and environmental factors when comparing subsistence uses in the study year with other years, such as increasing costs of fuel and purchased food, commercial fisheries harvests and bycatch, more persistent storms and less predictable winds, and reduced sea ice. Such conditions affect resource abundance and locations as well as access to fish and wildlife populations, and may shape long-term trends. So far, as in the past, families and communities have adapted to changing economic, social, and environmental conditions, but the future is less clear if such changes intensify or accelerate. Local community residents should be essential partners in future efforts to understand these complex processes that affect the natural resources of the Bering Sea.

Optimization of Chlorella vulgaris and bioflocculant-producing bacteria co-culture: enhancing microalgae harvesting and lipid content.

PubMed

Wang, Y; Yang, Y; Ma, F; Xuan, L; Xu, Y; Huo, H; Zhou, D; Dong, S

2015-05-01

Microalgae are a sustainable bioresource, and the biofuel they produce is widely considered to be an alternative to limited natural fuel resources. However, microalgae harvesting is a bottleneck in the development of technology. Axenic Chlorella vulgaris microalgae exhibit poor harvesting, as expressed by a flocculation efficiency of 0·2%. This work optimized the co-culture conditions of C. vulgaris and bioflocculant-producing bacteria in synthetic wastewater using response surface methodology (RSM), thus aiming to enhance C. vulgaris harvesting and lipid content. Three significant process variables- inoculation ratio of bacteria and microalgae, initial glucose concentration, and co-culture time- were proposed in the RSM model. F-values (3·98/8·46) and R(2) values (0·7817/0·8711) both indicated a reasonable prediction by the RSM model. The results showed that C. vulgaris harvesting efficiency reached 45·0-50·0%, and the lipid content was over 21·0% when co-cultured with bioflocculant-producing bacteria under the optimized culture conditions of inoculation ratio of bacteria and microalgae of 0·20-0·25, initial glucose concentration of <1·5 kg m(-3) and co-culture time of 9-14 days. This work provided new insights into microalgae harvesting and cost-effective microalgal bioproducts, and confirmed the promising prospect of introducing bioflocculant-producing bacteria into microalgae bioenergy production. This work optimized the co-culture conditions of microalgae (C. vulgaris) and bioflocculant-producing bacteria (F2, Rhizobium radiobacter) in synthetic wastewater using response surface methodology, aiming to enhance C. vulgaris harvesting and lipid produced content. Bioflocculant-producing microbes are environmentally friendly functional materials. They avoid the negative effects of traditional chemical flocculants. This work provided new insights into microalgae harvesting and cost-effective production of microalgal bioproducts, and confirmed the promising prospect of introducing bioflocculant-producing bacteria into microalgae bioenergy production. © 2015 The Society for Applied Microbiology.

An ultra-low power CMOS image sensor with on-chip energy harvesting and power management capability.

PubMed

Cevik, Ismail; Huang, Xiwei; Yu, Hao; Yan, Mei; Ay, Suat U

2015-03-06

An ultra-low power CMOS image sensor with on-chip energy harvesting and power management capability is introduced in this paper. The photodiode pixel array can not only capture images but also harvest solar energy. As such, the CMOS image sensor chip is able to switch between imaging and harvesting modes towards self-power operation. Moreover, an on-chip maximum power point tracking (MPPT)-based power management system (PMS) is designed for the dual-mode image sensor to further improve the energy efficiency. A new isolated P-well energy harvesting and imaging (EHI) pixel with very high fill factor is introduced. Several ultra-low power design techniques such as reset and select boosting techniques have been utilized to maintain a wide pixel dynamic range. The chip was designed and fabricated in a 1.8 V, 1P6M 0.18 µm CMOS process. Total power consumption of the imager is 6.53 µW for a 96 × 96 pixel array with 1 V supply and 5 fps frame rate. Up to 30 μW of power could be generated by the new EHI pixels. The PMS is capable of providing 3× the power required during imaging mode with 50% efficiency allowing energy autonomous operation with a 72.5% duty cycle.

Improving rapeseed production practices in the southeastern United States

DOE Office of Scientific and Technical Information (OSTI.GOV)

Thomas, D.L.; Breve, M.A.; Raymer, P.L.

1990-04-01

Oilseed rape or rapeseed is a crop which offers a potential for double-cropping in the southeastern United States. This final project report describes the results from a three year study aimed at evaluating the effect of different planting and harvesting practices on establishment and yield of three rape cultivars, and the double cropping potential of rapeseed in the southeastern United States. The project was conducted on two yield sites in Tifton, Georgia during 1986--87, 1987--88 and 1988--89. The general objective of this research is to improve the seed and biomass yield of winter rapeseed in the southeastern United States bymore » developing appropriate agronomic practices for the region. The primary constraint is to grow rapeseed within the allowable period for double cropping with an economically desirable crop, such as peanut or soybean. Planting and harvesting are the most critical steps in this process. Therefore, the specific objectives of this research were: evaluate and improve the emergence of rapeseed by developing planting techniques that enhance the soil, water and seed regimes for winter rapeseed in the southeast, and evaluate and improve the yields of harvested rapeseed by developing techniques for determining the optimum timing of harvest and efficient methods for harvesting winter rapeseed in the southeast. 6 refs., 12 figs., 9 tabs.« less

Cellulose-Based Nanomaterials for Energy Applications.

PubMed

Wang, Xudong; Yao, Chunhua; Wang, Fei; Li, Zhaodong

2017-11-01

Cellulose is the most abundant natural polymer on earth, providing a sustainable green resource that is renewable, degradable, biocompatible, and cost effective. Recently, nanocellulose-based mesoporous structures, flexible thin films, fibers, and networks are increasingly developed and used in photovoltaic devices, energy storage systems, mechanical energy harvesters, and catalysts components, showing tremendous materials science value and application potential in many energy-related fields. In this Review, the most recent advancements of processing, integration, and application of cellulose nanomaterials in the areas of solar energy harvesting, energy storage, and mechanical energy harvesting are reviewed. For solar energy harvesting, promising applications of cellulose-based nanostructures for both solar cells and photoelectrochemical electrodes development are reviewed, and their morphology-related merits are discussed. For energy storage, the discussion is primarily focused on the applications of cellulose-based nanomaterials in lithium-ion batteries, including electrodes (e.g., active materials, binders, and structural support), electrolytes, and separators. Applications of cellulose nanomaterials in supercapacitors are also reviewed briefly. For mechanical energy harvesting, the most recent technology evolution in cellulose-based triboelectric nanogenerators is reviewed, from fundamental property tuning to practical implementations. At last, the future research potential and opportunities of cellulose nanomaterials as a new energy material are discussed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

An Automated and Minimally Invasive Tool for Generating Autologous Viable Epidermal Micrografts

PubMed Central

Osborne, Sandra N.; Schmidt, Marisa A.; Harper, John R.

2016-01-01

ABSTRACT OBJECTIVE: A new epidermal harvesting tool (CelluTome; Kinetic Concepts, Inc, San Antonio, Texas) created epidermal micrografts with minimal donor site damage, increased expansion ratios, and did not require the use of an operating room. The tool, which applies both heat and suction concurrently to normal skin, was used to produce epidermal micrografts that were assessed for uniform viability, donor-site healing, and discomfort during and after the epidermal harvesting procedure. DESIGN: This study was a prospective, noncomparative institutional review board–approved healthy human study to assess epidermal graft viability, donor-site morbidity, and patient experience. SETTING: These studies were conducted at the multispecialty research facility, Clinical Trials of Texas, Inc, San Antonio. PATIENTS: The participants were 15 healthy human volunteers. RESULTS: The average viability of epidermal micrografts was 99.5%. Skin assessment determined that 76% to 100% of the area of all donor sites was the same in appearance as the surrounding skin within 14 days after epidermal harvest. A mean pain of 1.3 (on a scale of 1 to 5) was reported throughout the harvesting process. CONCLUSIONS: Use of this automated, minimally invasive harvesting system provided a simple, low-cost method of producing uniformly viable autologous epidermal micrografts with minimal patient discomfort and superficial donor-site wound healing within 2 weeks. PMID:26765157

An Automated and Minimally Invasive Tool for Generating Autologous Viable Epidermal Micrografts.

PubMed

Osborne, Sandra N; Schmidt, Marisa A; Harper, John R

2016-02-01

A new epidermal harvesting tool (CelluTome; Kinetic Concepts, Inc, San Antonio, Texas) created epidermal micrografts with minimal donor site damage, increased expansion ratios, and did not require the use of an operating room. The tool, which applies both heat and suction concurrently to normal skin, was used to produce epidermal micrografts that were assessed for uniform viability, donor-site healing, and discomfort during and after the epidermal harvesting procedure. This study was a prospective, noncomparative institutional review board-approved healthy human study to assess epidermal graft viability, donor-site morbidity, and patient experience. These studies were conducted at the multispecialty research facility, Clinical Trials of Texas, Inc, San Antonio. The participants were 15 healthy human volunteers. The average viability of epidermal micrografts was 99.5%. Skin assessment determined that 76% to 100% of the area of all donor sites was the same in appearance as the surrounding skin within 14 days after epidermal harvest. A mean pain of 1.3 (on a scale of 1 to 5) was reported throughout the harvesting process. Use of this automated, minimally invasive harvesting system provided a simple, low-cost method of producing uniformly viable autologous epidermal micrografts with minimal patient discomfort and superficial donor-site wound healing within 2 weeks.

Concurrent Harvesting of Ambient Energy by Hybrid Nanogenerators for Wearable Self-Powered Systems and Active Remote Sensing.

PubMed

Zheng, Haiwu; Zi, Yunlong; He, Xu; Guo, Hengyu; Lai, Ying-Chih; Wang, Jie; Zhang, Steven L; Wu, Changsheng; Cheng, Gang; Wang, Zhong Lin

2018-05-02

Harvesting energy available from ambient environment is highly desirable for powering personal electronics and health applications. Due to natural process and human activities, steam can be produced by boilers, human perspiration, and the wind exists ubiquitously. In the outdoor environment, these two phenomena usually exist at the same place, which contain heat and mechanical energies simultaneously. However, previous studies have isolated them as separate sources of energy to harvest and hence failed to utilize them effectively. Herein, we present unique hybrid nanogenerators for individually/simultaneously harvesting thermal energy from water vapors and mechanical energy from intermittent wind blowing from the bottom side, which consist of a wind-driven triboelectric nanogenerator (TENG) and pyroelectric-piezoelectric nanogenerators (PPENGs). The output power of the PPENG and the TENG can be up to about 184.32 μW and 4.74 mW, respectively, indicating the TENG plays the dominant role. Our hybrid nanogenerators could provide different applications such as to power digital watch and enable self-powered sensing with wireless transmission. The device could also be further integrated into a face mask for potentially wearable applications. This work not only provides a promising approach for renewable energy harvesting but also enriches potential applications for self-powered systems and wireless sensors.

Monitoring Seasonal Changes in Winery-Resident Microbiota.

PubMed

Bokulich, Nicholas A; Ohta, Moe; Richardson, Paul M; Mills, David A

2013-01-01

During the transformation of grapes to wine, wine fermentations are exposed to a large area of specialized equipment surfaces within wineries, which may serve as important reservoirs for two-way transfer of microbes between fermentations. However, the role of winery environments in shaping the microbiota of wine fermentations and vectoring wine spoilage organisms is poorly understood at the systems level. Microbial communities inhabiting all major equipment and surfaces in a pilot-scale winery were surveyed over the course of a single harvest to track the appearance of equipment microbiota before, during, and after grape harvest. Results demonstrate that under normal cleaning conditions winery surfaces harbor seasonally fluctuating populations of bacteria and fungi. Surface microbial communities were dependent on the production context at each site, shaped by technological practices, processing stage, and season. During harvest, grape- and fermentation-associated organisms populated most winery surfaces, acting as potential reservoirs for microbial transfer between fermentations. These surfaces harbored large populations of Saccharomyces cerevisiae and other yeasts prior to harvest, potentially serving as an important vector of these yeasts in wine fermentations. However, the majority of the surface communities before and after harvest comprised organisms with no known link to wine fermentations and a near-absence of spoilage-related organisms, suggesting that winery surfaces do not overtly vector wine spoilage microbes under normal operating conditions.

Monitoring Seasonal Changes in Winery-Resident Microbiota

PubMed Central

Bokulich, Nicholas A.; Ohta, Moe; Richardson, Paul M.; Mills, David A.

2013-01-01

During the transformation of grapes to wine, wine fermentations are exposed to a large area of specialized equipment surfaces within wineries, which may serve as important reservoirs for two-way transfer of microbes between fermentations. However, the role of winery environments in shaping the microbiota of wine fermentations and vectoring wine spoilage organisms is poorly understood at the systems level. Microbial communities inhabiting all major equipment and surfaces in a pilot-scale winery were surveyed over the course of a single harvest to track the appearance of equipment microbiota before, during, and after grape harvest. Results demonstrate that under normal cleaning conditions winery surfaces harbor seasonally fluctuating populations of bacteria and fungi. Surface microbial communities were dependent on the production context at each site, shaped by technological practices, processing stage, and season. During harvest, grape- and fermentation-associated organisms populated most winery surfaces, acting as potential reservoirs for microbial transfer between fermentations. These surfaces harbored large populations of Saccharomyces cerevisiae and other yeasts prior to harvest, potentially serving as an important vector of these yeasts in wine fermentations. However, the majority of the surface communities before and after harvest comprised organisms with no known link to wine fermentations and a near-absence of spoilage-related organisms, suggesting that winery surfaces do not overtly vector wine spoilage microbes under normal operating conditions. PMID:23840468

Electronic optimization for an energy harvesting system based on magnetoelectric Metglas/poly(vinylidene fluoride)/Metglas composites

NASA Astrophysics Data System (ADS)

Reis, S.; Silva, M. P.; Castro, N.; Correia, V.; Rocha, J. G.; Martins, P.; Lasheras, A.; Gutierrez, J.; Lanceros-Mendez, S.

2016-08-01

Harvesting magnetic energy from the environment is becoming increasingly attractive for being a renewable and inexhaustible power source, ubiquitous and accessible in remote locations. In particular, magnetic harvesting with polymer-based magnetoelectric (ME) materials meet the industry demands of being flexible, showing large area potential, lightweight and biocompatibility. In order to get the best energy harvesting process, the extraction circuit needs to be optimized in order to be useful for powering devices. This paper discusses the design and performance of five interface circuits, a full-wave bridge rectifier, two Cockcroft-Walton voltage multipliers (with 1 and 2 stages) and two Dickson voltage multipliers (with 2 and 3 stages), for the energy harvesting from a Fe61.6Co16.4Si10.8B11.2 (Metglas)/polyvinylidene fluoride/Metglas ME composite. Maximum power and power density values of 12 μW and 0.9 mW cm-3 were obtained, respectively, with the Dickson voltage multiplier with two stages, for a load resistance of 180 kΩ, at 7 Oe DC magnetic field and a 54.5 kHz resonance frequency. Such performance is useful for microdevice applications in hard-to-reach locations and for traditional devices such as electric windows, door locking, and tire pressure monitoring.

United States Department of Agriculture-Agricultural Research Service research on alternatives to methyl bromide: pre-plant and post-harvest.

PubMed

Schneider, Sally M; Rosskopf, Erin N; Leesch, James G; Chellemi, Daniel O; Bull, Carolee T; Mazzola, Mark

2003-01-01

Methyl bromide is a widely used fumigant for both pre-plant and post-harvest pest and pathogen control. The Montreal Protocol and the US Clean Air Act mandate a phase-out of the import and manufacture of methyl bromide, beginning in 2001 and culminating with a complete ban, except for quarantine and certain pre-shipment uses and exempted critical uses, in January 2005. In 1995, ARS built on its existing programs in soil-borne plant pathology and post-harvest entomology and plant pathology to initiate a national research program to develop alternatives to methyl bromide. The focus has been on strawberry, pepper, tomato, perennial and nursery cropping systems for pre-plant methyl bromide use and fresh and durable commodities for post-harvest use. Recently the program has been expanded to include research on alternatives for the ornamental and cut flower cropping systems. An overview of the national research program is presented. Results from four specific research trials are presented, ranging from organic to conventional systems. Good progress on short-term alternatives is being made. These will be used as the foundation of integrated management systems which begin with pre-plant management decisions and continue through post-harvest processing.

An Ultra-Low Power CMOS Image Sensor with On-Chip Energy Harvesting and Power Management Capability

PubMed Central

Cevik, Ismail; Huang, Xiwei; Yu, Hao; Yan, Mei; Ay, Suat U.

2015-01-01

An ultra-low power CMOS image sensor with on-chip energy harvesting and power management capability is introduced in this paper. The photodiode pixel array can not only capture images but also harvest solar energy. As such, the CMOS image sensor chip is able to switch between imaging and harvesting modes towards self-power operation. Moreover, an on-chip maximum power point tracking (MPPT)-based power management system (PMS) is designed for the dual-mode image sensor to further improve the energy efficiency. A new isolated P-well energy harvesting and imaging (EHI) pixel with very high fill factor is introduced. Several ultra-low power design techniques such as reset and select boosting techniques have been utilized to maintain a wide pixel dynamic range. The chip was designed and fabricated in a 1.8 V, 1P6M 0.18 µm CMOS process. Total power consumption of the imager is 6.53 µW for a 96 × 96 pixel array with 1 V supply and 5 fps frame rate. Up to 30 μW of power could be generated by the new EHI pixels. The PMS is capable of providing 3× the power required during imaging mode with 50% efficiency allowing energy autonomous operation with a 72.5% duty cycle. PMID:25756863

Ultrasonic wireless health monitoring

NASA Astrophysics Data System (ADS)

Petit, Lionel; Lefeuvre, Elie; Guyomar, Daniel; Richard, Claude; Guy, Philippe; Yuse, Kaori; Monnier, Thomas

2006-03-01

The integration of autonomous wireless elements in health monitoring network increases the reliability by suppressing power supplies and data transmission wiring. Micro-power piezoelectric generators are an attractive alternative to primary batteries which are limited by a finite amount of energy, a limited capacity retention and a short shelf life (few years). Our goal is to implement such an energy harvesting system for powering a single AWT (Autonomous Wireless Transmitter) using our SSH (Synchronized Switch Harvesting) method. Based on a non linear process of the piezoelement voltage, this SSH method optimizes the energy extraction from the mechanical vibrations. This AWT has two main functions : The generation of an identifier code by RF transmission to the central receiver and the Lamb wave generation for the health monitoring of the host structure. A damage index is derived from the variation between the transmitted wave spectrum and a reference spectrum. The same piezoelements are used for the energy harvesting function and the Lamb wave generation, thus reducing mass and cost. A micro-controller drives the energy balance and synchronizes the functions. Such an autonomous transmitter has been evaluated on a 300x50x2 mm 3 composite cantilever beam. Four 33x11x0.3 mm 3 piezoelements are used for the energy harvesting and for the wave lamb generation. A piezoelectric sensor is placed at the free end of the beam to track the transmitted Lamb wave. In this configuration, the needed energy for the RF emission is 0.1 mJ for a 1 byte-information and the Lamb wave emission requires less than 0.1mJ. The AWT can harvested an energy quantity of approximately 20 mJ (for a 1.5 Mpa lateral stress) with a 470 μF storage capacitor. This corresponds to a power density near to 6mW/cm 3. The experimental AWT energy abilities are presented and the damage detection process is discussed. Finally, some envisaged solutions are introduced for the implementation of the required data processing into an autonomous wireless receiver, in terms of reduction of the energy and memory costs.

ARS labs update to California Cotton Ginners and Growers

USDA-ARS?s Scientific Manuscript database

There are four USDA-ARS labs involved in cotton harvesting, processing & fiber quality research; The Southwestern Cotton Ginning Research Laboratory (Mesilla Park, NM); The Cotton Production and Processing Unit (Lubbock, TX); The Cotton Ginning Research Unit (Stoneville, MS); and The Cotton Structur...

Updraft gasification of salmon processing waste

USDA-ARS?s Scientific Manuscript database

The purpose of this research is to judge the feasibility of gasification for the disposal of waste streams generated through salmon harvesting. Gasification is the process of converting carbonaceous materials into combustible “syngas” in a high temperature (above 700 °C), oxygen deficient environmen...

50 CFR 401.4 - Activities prohibited.

Code of Federal Regulations, 2010 CFR

2010-10-01

..., DEVELOPMENT AND ENHANCEMENT § 401.4 Activities prohibited. Law enforcement, public relations, harvesting, marketing and processing activities, construction of fisherman use facilities, and activities concerned with...

Biomechanics of Wheat/Barley Straw and Corn Stover

DOE Office of Scientific and Technical Information (OSTI.GOV)

Christopher T. Wright; Peter A. Pryfogle; Nathan A. Stevens

2005-03-01

The lack of understanding of the mechanical characteristics of cellulosic feedstocks is a limiting factor in economically collecting and processing crop residues, primarily wheat and barley stems and corn stover. Several testing methods, including compression, tension, and bend have been investigated to increase our understanding of the biomechanical behavior of cellulosic feedstocks. Biomechanical data from these tests can provide required input to numerical models and help advance harvesting, handling, and processing techniques. In addition, integrating the models with the complete data set from this study can identify potential tools for manipulating the biomechanical properties of plant varieties in such amore » manner as to optimize their physical characteristics to produce higher value biomass and more energy efficient harvesting practices.« less

Energy neutral and low power wireless communications

NASA Astrophysics Data System (ADS)

Orhan, Oner

Wireless sensor nodes are typically designed to have low cost and small size. These design objectives impose restrictions on the capacity and efficiency of the transceiver components and energy storage units that can be used. As a result, energy becomes a bottleneck and continuous operation of the sensor network requires frequent battery replacements, increasing the maintenance cost. Energy harvesting and energy efficient transceiver architectures are able to overcome these challenges by collecting energy from the environment and utilizing the energy in an intelligent manner. However, due to the nature of the ambient energy sources, the amount of useful energy that can be harvested is limited and unreliable. Consequently, optimal management of the harvested energy and design of low power transceivers pose new challenges for wireless network design and operation. The first part of this dissertation is on energy neutral wireless networking, where optimal transmission schemes under different system setups and objectives are investigated. First, throughput maximization for energy harvesting two-hop networks with decode-and-forward half-duplex relays is studied. For a system with two parallel relays, various combinations of the following four transmission modes are considered: Broadcast from the source, multi-access from the relays, and successive relaying phases I and II. Next, the energy cost of the processing circuitry as well as the transmission energy are taken into account for communication over a broadband fading channel powered by an energy harvesting transmitter. Under this setup, throughput maximization, energy maximization, and transmission completion time minimization problems are studied. Finally, source and channel coding for an energy-limited wireless sensor node is investigated under various energy constraints including energy harvesting, processing and sampling costs. For each objective, optimal transmission policies are formulated as the solutions of a convex optimization problem, and the properties of these optimal policies are identified. In the second part of this thesis, low power transceiver design is considered for millimeter wave communication systems. In particular, using an additive quantization noise model, the effect of analog-digital conversion (ADC) resolution and bandwidth on the achievable rate is investigated for a multi-antenna system under a receiver power constraint. Two receiver architectures, analog and digital combining, are compared in terms of performance.

An assessment of dispersing pollutants from the pre-harvest burning of sugarcane in rural areas in the northeast of Brazil

NASA Astrophysics Data System (ADS)

Rangel, Maria Gabriela L.; Henríquez, Jorge R.; Costa, José A. P.; de Lira Junior, José C.

2018-04-01

In recent years, the Brazilian government has been applying several restrictions with regard to preventing environmental pollution. Although Brazilian legislation is becoming stricter as to the pre-harvest burning of sugarcane, this practice is frequently used in order to assist manual harvesting. In the northeast region of Brazil, sugarcane is an important crop, which accounts for about 15% of the national production in a total area of 1,060,660 ha, the average production being 51,119 kg per hectare. The pre-harvest burning of sugarcane generates smoke, which has a high concentration of atmospheric pollutants such as carbon dioxide (CO2), carbon monoxide (CO), particulate matter (P.M. 2.5 and 10), polycyclic aromatic hydrocarbons (PAH), volatile organic compounds (VOC) and nitrogen oxides (NOX). This article estimates the volume of CO, P.M. 2.5 and NOX generated and how they are dispersed in the atmosphere when this arises from the burning of sugarcane biomass in rural areas of Northeast Brazil, and does so by using AERMOD VIEW® simulation software. Using the characteristics of the emissions and environmental (meteorological and topographical) data, quality air profiles based on pollutant dispersion were obtained. Three studies were taken into account in order to determine the relationship between pollutant dispersion and some parameters of the burning process, such as those for the spatial distribution of resources, the duration of pre-harvest burning and the influence of undertaking burning in different months. As to spatial distribution, to divide an area into small lots contributes to decreasing the maximum concentration of pollutants by 53% compared to burning a single area of equivalent size. The study of the burning duration indicated that doing so gradually (using a lengthier procedure) could decrease the maximum concentration of the pollutants by an inverse relation. The harvesting period in this region is between November and April. The pollutants dispersion process was greatest in February. April presented the worst dispersion conditions, and was associated with the highest pollutant concentrations.

Assessment and speciation of chlorine demand in fresh-cut produce wash water

USDA-ARS?s Scientific Manuscript database

Production of high quality, fresh-cut produce is a key driver for the produce industry. A critical area of concern is the chlorinated wash water used during post-harvest processing in large industrial processing facilities. Predominantly using a batch process, wash water is recycled over 8hr shift...

Solar energy in food processing-a critical appraisal.

PubMed

Eswara, Amruta R; Ramakrishnarao, M

2013-04-01

Increasing population and high cost of fuels have created opportunities for using alternate energies for post-harvest processing of foods. Solar food processing is an emerging technology that provides good quality foods at low or no additional fuel costs. A number of solar dryers, collectors and concentrators are currently being used for various steps in food processing and value addition. Society for Energy, Environment and Development (SEED) developed Solar Cabinet Dryer with forced circulation which has been used for dehydration and development of value added products from locally grown fruits, vegetables, leafy greens and forest produce. Drying under simulated shade conditions using UV-reducing Blue filter helps retain nutrients better. Its simple design and ease of handling makes SEED Solar Dryer an ideal choice for application of food processing in rural settings, closer to where the harvest is produced, eliminating the need for expensive transportation or storage of fresh produce. It also creates employment opportunities among the rural population, especially women. Other gadgets based on solar collectors and concentrators currently being used at various steps of food processing are reviewed.

A modeling framework for integrated harvest and habitat management of North American waterfowl: Case-study of northern pintail metapopulation dynamics

USGS Publications Warehouse

Mattsson, Brady J.; Runge, M.C.; Devries, J.H.; Boomer, G.S.; Eadie, J.M.; Haukos, D.A.; Fleskes, J.P.; Koons, D.N.; Thogmartin, W.E.; Clark, R.G.

2012-01-01

We developed and evaluated the performance of a metapopulation model enabling managers to examine, for the first time, the consequences of alternative management strategies involving habitat conditions and hunting on both harvest opportunity and carrying capacity (i.e., equilibrium population size in the absence of harvest) for migratory waterfowl at a continental scale. Our focus is on the northern pintail (Anas acuta; hereafter, pintail), which serves as a useful model species to examine the potential for integrating waterfowl harvest and habitat management in North America. We developed submodel structure capturing important processes for pintail populations during breeding, fall migration, winter, and spring migration while encompassing spatial structure representing three core breeding areas and two core nonbreeding areas. A number of continental-scale predictions from our baseline parameterization (e.g., carrying capacity of 5.5 million, equilibrium population size of 2.9 million and harvest rate of 12% at maximum sustained yield [MSY]) were within 10% of those from the pintail harvest strategy under current use by the U.S. Fish and Wildlife Service. To begin investigating the interaction of harvest and habitat management, we examined equilibrium population conditions for pintail at the continental scale across a range of harvest rates while perturbing model parameters to represent: (1) a 10% increase in breeding habitat quality in the Prairie Pothole population (PR); and (2) a 10% increase in nonbreeding habitat quantity along in the Gulf Coast (GC). Based on our model and analysis, a greater increase in carrying capacity and sustainable harvest was seen when increasing a proxy for habitat quality in the Prairie Pothole population. This finding and underlying assumptions must be critically evaluated, however, before specific management recommendations can be made. To make such recommendations, we require (1) extended, refined submodels with additional parameters linking influences of habitat management and environmental conditions to key life-history parameters; (2) a formal sensitivity analysis of the revised model; (3) an integrated population model that incorporates empirical data for estimating key vital rates; and (4) cost estimates for changing these additional parameters through habitat management efforts. We foresee great utility in using an integrated modeling approach to predict habitat and harvest management influences on continental-scale population responses while explicitly considering putative effects of climate change. Such a model could be readily adapted for management of many habitat-limited species.

Biomass Logistics

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. Richard Hess; Kevin L. Kenney; William A. Smith

Equipment manufacturers have made rapid improvements in biomass harvesting and handling equipment. These improvements have increased transportation and handling efficiencies due to higher biomass densities and reduced losses. Improvements in grinder efficiencies and capacity have reduced biomass grinding costs. Biomass collection efficiencies (the ratio of biomass collected to the amount available in the field) as high as 75% for crop residues and greater than 90% for perennial energy crops have also been demonstrated. However, as collection rates increase, the fraction of entrained soil in the biomass increases, and high biomass residue removal rates can violate agronomic sustainability limits. Advancements inmore » quantifying multi-factor sustainability limits to increase removal rate as guided by sustainable residue removal plans, and mitigating soil contamination through targeted removal rates based on soil type and residue type/fraction is allowing the use of new high efficiency harvesting equipment and methods. As another consideration, single pass harvesting and other technologies that improve harvesting costs cause biomass storage moisture management challenges, which challenges are further perturbed by annual variability in biomass moisture content. Monitoring, sampling, simulation, and analysis provide basis for moisture, time, and quality relationships in storage, which has allowed the development of moisture tolerant storage systems and best management processes that combine moisture content and time to accommodate baled storage of wet material based upon “shelf-life.” The key to improving biomass supply logistics costs has been developing the associated agronomic sustainability and biomass quality technologies and processes that allow the implementation of equipment engineering solutions.« less

Toward efficient aeroelastic energy harvesting through limit cycle shaping

NASA Astrophysics Data System (ADS)

Kirschmeier, Benjamin; Bryant, Matthew

2016-04-01

Increasing demand to harvest energy from renewable resources has caused significant research interest in unsteady aerodynamic and hydrodynamic phenomena. Apart from the traditional horizontal axis wind turbines, there has been significant growth in the study of bio-inspired oscillating wings for energy harvesting. These systems are being built to harvest electricity for wireless devices, as well as for large scale mega-watt power generation. Such systems can be driven by aeroelastic flutter phenomena which, beyond a critical wind speed, will cause the system to enter into limitcycle oscillations. When the airfoil enters large amplitude, high frequency motion, leading and trailing edge vortices form and, when properly synchronized with the airfoil kinematics, enhance the energy extraction efficiency of the device. A reduced order dynamic stall model is employed on a nonlinear aeroelastic structural model to investigate whether the parameters of a fully passive aeroelastic device can be tuned to produce limit cycle oscillations at desired kinematics. This process is done through an optimization technique to find the necessary structural parameters to achieve desired structural forces and moments corresponding to a target limit cycle. Structural nonlinearities are explored to determine the essential nonlinearities such that the system's limit cycle closely matches the desired kinematic trajectory. The results from this process demonstrate that it is possible to tune system parameters such that a desired limit cycle trajectory can be achieved. The simulations also demonstrate that the high efficiencies predicted by previous computational aerodynamics studies can be achieved in fully passive aeroelastic devices.

Enzyme-Triggered Defined Protein Nanoarrays: Efficient Light-Harvesting Systems to Mimic Chloroplasts.

PubMed

Zhao, Linlu; Zou, Haoyang; Zhang, Hao; Sun, Hongcheng; Wang, Tingting; Pan, Tiezheng; Li, Xiumei; Bai, Yushi; Qiao, Shanpeng; Luo, Quan; Xu, Jiayun; Hou, Chunxi; Liu, Junqiu

2017-01-24

The elegance and efficiency by which chloroplasts harvest solar energy and conduct energy transfer have been a source of inspiration for chemists to mimic such process. However, precise manipulation to obtain orderly arranged antenna chromophores in constructing artificial chloroplast mimics was a great challenge, especially from the structural similarity and bioaffinity standpoints. Here we reported a design strategy that combined covalent and noncovalent interactions to prepare a protein-based light-harvesting system to mimic chloroplasts. Cricoid stable protein one (SP1) was utilized as a building block model. Under enzyme-triggered covalent protein assembly, mutant SP1 with tyrosine (Tyr) residues at the designated sites can couple together to form nanostructures. Through controlling the Tyr sites on the protein surface, we can manipulate the assembly orientation to respectively generate 1D nanotubes and 2D nanosheets. The excellent stability endowed the self-assembled protein architectures with promising applications. We further integrated quantum dots (QDs) possessing optical and electronic properties with the 2D nanosheets to fabricate chloroplast mimics. By attaching different sized QDs as donor and acceptor chromophores to the negatively charged surface of SP1-based protein nanosheets via electrostatic interactions, we successfully developed an artificial light-harvesting system. The assembled protein nanosheets structurally resembled the natural thylakoids, and the QDs can achieve pronounced FRET phenomenon just like the chlorophylls. Therefore, the coassembled system was meaningful to explore the photosynthetic process in vitro, as it was designed to mimic the natural chloroplast.

Motorcycle waste heat energy harvesting

NASA Astrophysics Data System (ADS)

Schlichting, Alexander D.; Anton, Steven R.; Inman, Daniel J.

2008-03-01

Environmental concerns coupled with the depletion of fuel sources has led to research on ethanol, fuel cells, and even generating electricity from vibrations. Much of the research in these areas is stalling due to expensive or environmentally contaminating processes, however recent breakthroughs in materials and production has created a surge in research on waste heat energy harvesting devices. The thermoelectric generators (TEGs) used in waste heat energy harvesting are governed by the Thermoelectric, or Seebeck, effect, generating electricity from a temperature gradient. Some research to date has featured platforms such as heavy duty diesel trucks, model airplanes, and automobiles, attempting to either eliminate heavy batteries or the alternator. A motorcycle is another platform that possesses some very promising characteristics for waste heat energy harvesting, mainly because the exhaust pipes are exposed to significant amounts of air flow. A 1995 Kawasaki Ninja 250R was used for these trials. The module used in these experiments, the Melcor HT3-12-30, produced an average of 0.4694 W from an average temperature gradient of 48.73 °C. The mathematical model created from the Thermoelectric effect equation and the mean Seebeck coefficient displayed by the module produced an average error from the experimental data of 1.75%. Although the module proved insufficient to practically eliminate the alternator on a standard motorcycle, the temperature data gathered as well as the examination of a simple, yet accurate, model represent significant steps in the process of creating a TEG capable of doing so.

Evaluation of various harvesting methods for high-density microalgae, Aurantiochytrium sp. KRS101.

PubMed

Kim, Kyochan; Shin, Heewon; Moon, Myounghoon; Ryu, Byung-Gon; Han, Jong-In; Yang, Ji-Won; Chang, Yong Keun

2015-12-01

Five technologies, coagulation, electro-flotation (EF), electro-coagulation-flotation (ECF), centrifugation, and membrane filtration, were systematically assessed for their adequacy of harvesting Aurantiochytrium sp. KRS101, a heterotrophic microalgal species that has much higher biomass concentration than photoautotrophic species. Coagulation, EF, and ECF were found to have limited efficiency. Centrifugation was overly powerful to susceptible cells like Aurantiochytrium sp. KRS101, inducing cell rupture and consequently biomass loss of over 13%. Membrane filtration, in particular equipped with an anti-fouling turbulence generator, turned out to be best suited: nearly 100% of harvesting efficiency and low water content in harvested biomass were achieved. With rotation rate increased, high permeate fluxes could be attained even with extremely concentrated biomass: e.g., 219.0 and 135.0 L/m(2)/h at 150.0 and 203.0 g/L, respectively. Dynamic filtration appears to be indeed a suitable means especially to obtain highly concentrated biomass that have no need of dewatering and can be directly processed. Copyright © 2015 Elsevier Ltd. All rights reserved.

Systems identification and the adaptive management of waterfowl in the United States

USGS Publications Warehouse

Williams, B.K.; Nichols, J.D.

2001-01-01

Waterfowl management in the United States is one of the more visible conservation success stories in the United States. It is authorized and supported by appropriate legislative authorities, based on large-scale monitoring programs, and widely accepted by the public. The process is one of only a limited number of large-scale examples of effective collaboration between research and management, integrating scientific information with management in a coherent framework for regulatory decision-making. However, harvest management continues to face some serious technical problems, many of which focus on sequential identification of the resource system in a context of optimal decision-making. The objective of this paper is to provide a theoretical foundation of adaptive harvest management, the approach currently in use in the United States for regulatory decision-making. We lay out the legal and institutional framework for adaptive harvest management and provide a formal description of regulatory decision-making in terms of adaptive optimization. We discuss some technical and institutional challenges in applying adaptive harvest management and focus specifically on methods of estimating resource states for linear resource systems.

A metagenomic survey of forest soil microbial communities more than a decade after timber harvesting.

PubMed

Wilhelm, Roland C; Cardenas, Erick; Leung, Hilary; Maas, Kendra; Hartmann, Martin; Hahn, Aria; Hallam, Steven; Mohn, William W

2017-01-01

The scarcity of long-term data on soil microbial communities in the decades following timber harvesting limits current understanding of the ecological problems associated with maintaining the productivity of managed forests. The high complexity of soil communities and the heterogeneity of forest and soil necessitates a comprehensive approach to understand the role of microbial processes in managed forest ecosystems. Here, we describe a curated collection of well replicated, multi-faceted data from eighteen reforested sites in six different North American ecozones within the Long-term Soil Productivity (LTSP) Study, without detailed analysis of results or discussion. The experiments were designed to contrast microbial community composition and function among forest soils from harvested treatment plots with varying intensities of organic matter removal. The collection includes 724 bacterial (16S) and 658 fungal (ITS2) amplicon libraries, 133 shotgun metagenomic libraries as well as stable isotope probing amplicon libraries capturing the effects of harvesting on hemicellulolytic and cellulolytic populations. This collection serves as a foundation for the LTSP Study and other studies of the ecology of forest soil and forest disturbance.

A metagenomic survey of forest soil microbial communities more than a decade after timber harvesting

PubMed Central

Wilhelm, Roland C.; Cardenas, Erick; Leung, Hilary; Maas, Kendra; Hartmann, Martin; Hahn, Aria; Hallam, Steven; Mohn, William W.

2017-01-01

The scarcity of long-term data on soil microbial communities in the decades following timber harvesting limits current understanding of the ecological problems associated with maintaining the productivity of managed forests. The high complexity of soil communities and the heterogeneity of forest and soil necessitates a comprehensive approach to understand the role of microbial processes in managed forest ecosystems. Here, we describe a curated collection of well replicated, multi-faceted data from eighteen reforested sites in six different North American ecozones within the Long-term Soil Productivity (LTSP) Study, without detailed analysis of results or discussion. The experiments were designed to contrast microbial community composition and function among forest soils from harvested treatment plots with varying intensities of organic matter removal. The collection includes 724 bacterial (16S) and 658 fungal (ITS2) amplicon libraries, 133 shotgun metagenomic libraries as well as stable isotope probing amplicon libraries capturing the effects of harvesting on hemicellulolytic and cellulolytic populations. This collection serves as a foundation for the LTSP Study and other studies of the ecology of forest soil and forest disturbance. PMID:28765786

Insights into molecular and metabolic events associated with fruit response to post-harvest fungal pathogens

PubMed Central

Alkan, Noam; Fortes, Ana M.

2015-01-01

Due to post-harvest losses more than 30% of harvested fruits will not reach the consumers’ plate. Fungal pathogens play a key role in those losses, as they cause most of the fruit rots and the customer complaints. Many of the fungal pathogens are already present in the unripe fruit but remain quiescent during fruit growth until a particular phase of fruit ripening and senescence. The pathogens sense the developmental change and switch into the devastating necrotrophic life style that causes fruit rotting. Colonization of unripe fruit by the fungus initiates defensive responses that limit fungal growth and development. However, during fruit ripening several physiological processes occur that correlate with increased fruit susceptibility. In contrast to plant defenses in unripe fruit, the defense posture of ripe fruit entails a different subset of defense responses that will end with fruit rotting and losses. This review will focus on several aspects of molecular and metabolic events associated with fleshy fruit responses induced by post-harvest fungal pathogens during fruit ripening. PMID:26539204

Timber production assessment of a plantation forest: An integrated framework with field-based inventory, multi-source remote sensing data and forest management history

NASA Astrophysics Data System (ADS)

Gao, Tian; Zhu, Jiaojun; Deng, Songqiu; Zheng, Xiao; Zhang, Jinxin; Shang, Guiduo; Huang, Liyan

2016-10-01

Timber production is the purpose for managing plantation forests, and its spatial and quantitative information is critical for advising management strategies. Previous studies have focused on growing stock volume (GSV), which represents the current potential of timber production, yet few studies have investigated historical process-harvested timber. This resulted in a gap in a synthetical ecosystem service assessment of timber production. In this paper, we established a Management Process-based Timber production (MPT) framework to integrate the current GSV and the harvested timber derived from historical logging regimes, trying to synthetically assess timber production for a historical period. In the MPT framework, age-class and current GSV determine the times of historical thinning and the corresponding harvested timber, by using a ;space-for-time; substitution. The total timber production can be estimated by the historical harvested timber in each thinning and the current GSV. To test this MPT framework, an empirical study on a larch plantation (LP) with area of 43,946 ha was conducted in North China for a period from 1962 to 2010. Field-based inventory data was integrated with ALOS PALSAR (Advanced Land-Observing Satellite Phased Array L-band Synthetic Aperture Radar) and Landsat-8 OLI (Operational Land Imager) data for estimating the age-class and current GSV of LP. The random forest model with PALSAR backscatter intensity channels and OLI bands as input predictive variables yielded an accuracy of 67.9% with a Kappa coefficient of 0.59 for age-class classification. The regression model using PALSAR data produced a root mean square error (RMSE) of 36.5 m3 ha-1. The total timber production of LP was estimated to be 7.27 × 106 m3, with 4.87 × 106 m3 in current GSV and 2.40 × 106 m3 in harvested timber through historical thinning. The historical process-harvested timber accounts to 33.0% of the total timber production, which component has been neglected in the assessments for current status of plantation forests. Synthetically considering the RMSE for predictive GSV and misclassification of age-class, the error in timber production were supposed to range from -55.2 to 56.3 m3 ha-1. The MPT framework can be used to assess timber production of other tree species at a larger spatial scale, providing crucial information for a better understanding of forest ecosystem service.

Current Trends in the Detection of Sociocultural Signatures: Data-Driven Models

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sanfilippo, Antonio P.; Bell, Eric B.; Corley, Courtney D.

The harvesting of behavioral data and their analysis through evidence-based reasoning enable the detection of sociocultural signatures in their context to support situation awareness and decision making. Harvested data are used as training materials from which to infer computational models of sociocultural behaviors or calibrate parameters for such models. Harvested data also serve as evidence input that the models use to provide insights about observed and future behaviors for targets of interest. The harvested data is often the result of assembling diverse data types and aggregating them into a form suitable for analysis. Data need to be analyzed to bringmore » out the categories of content that are relevant to the domain being addressed in order to train or run a model. If, for example, we are modeling the intent of a group to engage in violent behavior using messages that the group has broadcasted, then these messages need to be processed to extract and measure indicators of violent intent. The extracted indicators and the associated measurements (e.g. rates or counts of occurrence) can then be used to train/calibrate and run computational models that assess the propensity for violence expressed in the source message. Ubiquitous access to the Internet, mobile telephony and technologies such as digital photography and digital video have enabled social media application platforms such as Facebook, YouTube, and Twitter that are altering the nature of human social interaction. The fast increasing pace of online social interaction introduces new challenges and opportunities for gathering sociocultural data. Challenges include the development of harvesting and processing techniques tailored to new data environments and formats (e.g. Twitter, Facebook), the integration of social media content with traditional media content, and the protection of personal privacy. As these and other challenges are addressed, a new wealth of behavioral data and data analysis methods becomes available that are shaping social computing as a strongly data-driven experimental discipline with an increasingly stronger impact on the decision-making process of groups and individuals alike. In this chapter, we review current advances and trends in the detection of sociocultural signatures. Specific embodiments of the issues discussed are provided with respect to the assessment of violent intent and sociopolitical contention. We begin by reviewing current approaches to the detection of sociocultural signatures in these domains. Next, we turn to the review of novel data harvesting methods for social media content. Finally, we discuss the application of sociocultural models to social media content, and conclude by commenting on current challenges and future developments.« less

Conceptual approach on harvesting PV dissipated heat for enhancing water evaporation

NASA Astrophysics Data System (ADS)

Latiff, N. Abdul; Ya'acob, M. E.; Yunos, Khairul Faezah Md.

2017-09-01

The fluctuating sun radiation in tropical climate conditions has significantly affected the output performance of the PV array and also processes related to direct-sun drying. Apart from this, the dissipated heat under PV array projected from photonic effects of generating electricity is currently wasted to the environment. This study shares some conceptual idea on a new approach for harvesting the dissipated heat energy from PV arrays for the purpose of enhancing water evaporation process. Field measurements for ambient temperature (Ta) and PV bottom surface temperature (FFb) are measured and recorded for calculating the evaporation rates at different condition in real time. The waste heat dissipated in this condition is proposed as a medium to increase evaporation thru speeding up the water condensation process. The significant increase of water evaporation rate based on Penman equation supports the idea of integration with landed PV array structures.

29 CFR 780.118 - “Harvesting.”

Code of Federal Regulations, 2013 CFR

2013-07-01

... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF... fruit, the stripping of bluegrass seed, and the digging up of shrubs and trees grown in a nursery... from their attachment to the soil or otherwise reduced to possession. For example, the processing of...

29 CFR 780.118 - “Harvesting.”

Code of Federal Regulations, 2011 CFR

2011-07-01

... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF... fruit, the stripping of bluegrass seed, and the digging up of shrubs and trees grown in a nursery... from their attachment to the soil or otherwise reduced to possession. For example, the processing of...

29 CFR 780.118 - “Harvesting.”

Code of Federal Regulations, 2010 CFR

2010-07-01

... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF... fruit, the stripping of bluegrass seed, and the digging up of shrubs and trees grown in a nursery... from their attachment to the soil or otherwise reduced to possession. For example, the processing of...

29 CFR 780.118 - “Harvesting.”

Code of Federal Regulations, 2012 CFR

2012-07-01

... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF... fruit, the stripping of bluegrass seed, and the digging up of shrubs and trees grown in a nursery... from their attachment to the soil or otherwise reduced to possession. For example, the processing of...

29 CFR 780.118 - “Harvesting.”

Code of Federal Regulations, 2014 CFR

2014-07-01

... INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF... fruit, the stripping of bluegrass seed, and the digging up of shrubs and trees grown in a nursery... from their attachment to the soil or otherwise reduced to possession. For example, the processing of...

50 CFR 270.2 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... restaurant trade, but whose primary business function is not the processing or packaging of fish or fish... processing vessels and any person in the business of acquiring (taking title to) fish directly from harvesters. Research means any type of research designed to advance the image, desirability, usage...

50 CFR 270.2 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... restaurant trade, but whose primary business function is not the processing or packaging of fish or fish... processing vessels and any person in the business of acquiring (taking title to) fish directly from harvesters. Research means any type of research designed to advance the image, desirability, usage...

50 CFR 270.2 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... restaurant trade, but whose primary business function is not the processing or packaging of fish or fish... processing vessels and any person in the business of acquiring (taking title to) fish directly from harvesters. Research means any type of research designed to advance the image, desirability, usage...

50 CFR 270.2 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... restaurant trade, but whose primary business function is not the processing or packaging of fish or fish... processing vessels and any person in the business of acquiring (taking title to) fish directly from harvesters. Research means any type of research designed to advance the image, desirability, usage...

50 CFR 270.2 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... restaurant trade, but whose primary business function is not the processing or packaging of fish or fish... processing vessels and any person in the business of acquiring (taking title to) fish directly from harvesters. Research means any type of research designed to advance the image, desirability, usage...

Quality of fresh-cut baby spinach grown under a floating trays system as affected by nitrogen fertilisation and innovative packaging treatments.

PubMed

Rodríguez-Hidalgo, Stephanie; Artés-Hernández, Francisco; Gómez, Perla A; Fernández, Juan Antonio; Artés, Francisco

2010-04-30

Alternative techniques for cultivation of leafy vegetables such as a floating tray system and unconventional gas mixtures for post-harvest active modified atmosphere packaging (MAP) could be of interest in the minimally processed vegetable industry. The combined effect of three pre-harvest fertilisation doses (8, 12 or 16 mmol N L(-1)) and three post-harvest MAP conditions (passive, super-atmospheric or N2O-enriched) on the main quality attributes of fresh-cut baby spinach leaves throughout 10 days at 5 degrees C was studied. After 8 days of shelf life, spinach leaves fertilised with 8 and 16 mmol N L(-1) and stored under N2O-enriched MAP showed the lowest microbial growth, with good sensory quality. Such combined treatments also preserved the total antioxidant capacity sampled at harvest (8 g ascorbic acid equivalent antioxidant capacity kg(-1) f.w.). A decrease of 10-20% in total vitamin C content regardless of N fertilisation and packaging treatment was found during shelf life. Total phenolics content at harvest was 2 g gallic acid equivalents kg(-1) f.w., which was slightly decreased or preserved during shelf life while total chlorophylls were preserved for all treatments assayed around 550 mg kg(-1) f.w. No clear effect of fertilisation doses was observed during post-harvest storage on overall quality of fresh-cut baby spinach leaves, while N2O-enriched atmospheres seems to be a promising alternative to passive MAP for extending shelf life.

An Energy Aware Adaptive Sampling Algorithm for Energy Harvesting WSN with Energy Hungry Sensors

PubMed Central

Srbinovski, Bruno; Magno, Michele; Edwards-Murphy, Fiona; Pakrashi, Vikram; Popovici, Emanuel

2016-01-01

Wireless sensor nodes have a limited power budget, though they are often expected to be functional in the field once deployed for extended periods of time. Therefore, minimization of energy consumption and energy harvesting technology in Wireless Sensor Networks (WSN) are key tools for maximizing network lifetime, and achieving self-sustainability. This paper proposes an energy aware Adaptive Sampling Algorithm (ASA) for WSN with power hungry sensors and harvesting capabilities, an energy management technique that can be implemented on any WSN platform with enough processing power to execute the proposed algorithm. An existing state-of-the-art ASA developed for wireless sensor networks with power hungry sensors is optimized and enhanced to adapt the sampling frequency according to the available energy of the node. The proposed algorithm is evaluated using two in-field testbeds that are supplied by two different energy harvesting sources (solar and wind). Simulation and comparison between the state-of-the-art ASA and the proposed energy aware ASA (EASA) in terms of energy durability are carried out using in-field measured harvested energy (using both wind and solar sources) and power hungry sensors (ultrasonic wind sensor and gas sensors). The simulation results demonstrate that using ASA in combination with an energy aware function on the nodes can drastically increase the lifetime of a WSN node and enable self-sustainability. In fact, the proposed EASA in conjunction with energy harvesting capability can lead towards perpetual WSN operation and significantly outperform the state-of-the-art ASA. PMID:27043559

Recent Advances in Physical Post-Harvest Treatments for Shelf-Life Extension of Cereal Crops

PubMed Central

Schmidt, Marcus; Zannini, Emanuele; Arendt, Elke K.

2018-01-01

As a result of the rapidly growing global population and limited agricultural area, sufficient supply of cereals for food and animal feed has become increasingly challenging. Consequently, it is essential to reduce pre- and post-harvest crop losses. Extensive research, featuring several physical treatments, has been conducted to improve cereal post-harvest preservation, leading to increased food safety and sustainability. Various pests can lead to post-harvest losses and grain quality deterioration. Microbial spoilage due to filamentous fungi and bacteria is one of the main reasons for post-harvest crop losses and mycotoxins can induce additional consumer health hazards. In particular, physical treatments have gained popularity making chemical additives unnecessary. Therefore, this review focuses on recent advances in physical treatments with potential applications for microbial post-harvest decontamination of cereals. The treatments discussed in this article were evaluated for their ability to inhibit spoilage microorganisms and degrade mycotoxins without compromising the grain quality. All treatments evaluated in this review have the potential to inhibit grain spoilage microorganisms. However, each method has some drawbacks, making industrial application difficult. Even under optimal processing conditions, it is unlikely that cereals can be decontaminated of all naturally occurring spoilage organisms with a single treatment. Therefore, future research should aim for the development of a combination of treatments to harness their synergistic properties and avoid grain quality deterioration. For the degradation of mycotoxins the same conclusion can be drawn. In addition, future research must investigate the fate of degraded toxins, to assess the toxicity of their respective degradation products. PMID:29565832

Geobacter Project

DOE Office of Scientific and Technical Information (OSTI.GOV)

Derek Lovley; Maddalena Coppi; Stacy Ciufo

Analysis of the Genetic Potential and Gene Expression of Microbial Communities Involved in the In Situ Bioremediation of Uranium and Harvesting Electrical Energy from Organic Matter The primary goal of this research is to develop conceptual and computational models that can describe the functioning of complex microbial communities involved in microbial processes of interest to the Department of Energy. Microbial Communities to be Investigated: (1) Microbial community associated with the in situ bioremediation of uranium-contaminated groundwater; and (2) Microbial community that is capable of harvesting energy from waste organic matter in the form of electricity.

Veg-03 Ground Harvest

NASA Image and Video Library

2016-12-05

Inside the Veggie flight laboratory in the Space Station Processing Facility at NASA’s Kennedy Space Center in Florida, Matthew Romeyn, a NASA Pathways intern from the University of Edinburgh in Scotland, harvests a portion of the 'Outredgeous' red romaine lettuce from the Veg-03 ground control unit. The purpose of the ground Veggie system is to provide a control group to compare against the lettuce grown in orbit on the International Space Station. Veg-03 will continue NASA’s deep space plant growth research to benefit the Earth and the agency’s journey to Mars.

Applications of mutant yeast strains with low glycogen storage capability

NASA Technical Reports Server (NTRS)

Petersen, G. R.; Schubert, W. W.; Stokes, B. O.

1981-01-01

Several strains of Hansenula polymorpha were selected for possible low glycogen storage characteristics based on a selective I2 staining procedure. The levels of storage carbohydrates in the mutant strains were found to be 44-70% of the levels in the parent strain for cultures harvested in stationary phase. Similar differences generally were not found for cells harvested in exponential phase. Yeast strains deficient in glycogen storage capability are valuable in increasing the relative protein value of microbial biomass and also may provide significant cost savings in substrate utilization in fermentative processes.

Influence of Moisture Content and Compression Axis on Physico-mechanical Properties of Shorea robusta Seeds

NASA Astrophysics Data System (ADS)

Shashikumar, C.; Pradhan, R. C.; Mishra, S.

2018-06-01

Shorea robusta (Sal) is mainly harvested and processed for its seed oil, which has diverse application in commercial food and non-food based industries. Before extraction of its oil, seeds undergo into various post-harvest unit operations. Physical and mechanical properties play an important role in the handling and other processing activity. In this study influence of moisture content and compression axis of sal seed on physico-mechanical properties were studied and their application are highlighted. The experiments were conducted at five different moisture levels of 6.38, 10.49, 13.63, 17.64, and 21.95% (d.b) at two different orientations. The first orientation is on major axis (LEN) of the seed, and the other orientation is on intermediate or minor axis (WID), which is right angle to the major axis. It was observed that 68% of sal seeds were of medium size group at initial moisture content of 10.49% (d.b). The mean length and width of sal seed was found to be 26.7 mm and 12.8 mm, respectively. It was found that values of hardness, deformation at hardness, deformation at hardness percentage and energy for rupture were higher in minor axis (WID) as compared to the major axis (LEN). The results provide necessary data that may be useful to engineers, scientists, industries in the design of a suitable post-harvest processing machine.

Development of delayed bitterness and effect of harvest date in stored juice from two complex citrus hybrids.

PubMed

Raithore, Smita; Dea, Sharon; McCollum, Greg; Manthey, John A; Bai, Jinhe; Leclair, Clotilde; Hijaz, Faraj; Narciso, Jan A; Baldwin, Elizabeth A; Plotto, Anne

2016-01-30

Mandarins and mandarin hybrids have excellent flavor and color attributes, making them good candidates for consumption as fresh fruit. When processed into juice, however, they are less palatable, as they develop delayed bitterness when stored for a period of time. In this study the kinetics of delayed bitterness in two citrus mandarin hybrid siblings, 'Ambersweet' and USDA 1-105-106, was explored by sensory and instrumental analyses. In addition to the bitter limonoids, other quality factors (i.e. sugars, acids, pH, soluble solids content (SSC), titratable acidity (TA) and the ratio SSC/TA) were also measured. The two citrus hybrid siblings had different chemical profiles, which were perceived by taste panels. USDA 1-105-106 developed delayed bitterness when the juice was stored for more than 4 h, similar to juice from 'Navel' oranges, but 'Ambersweet' did not. Bitterness in 'Ambersweet' was more affected by harvest maturity, as juice from earlier harvest had lower SSC but higher TA and bitter limonoids. Since juice of USDA 1-105-106 shows delayed bitterness when stored for more than 4 h, this cultivar is not suitable for juice processing. Our finding that siblings can differ in chemical and sensory properties emphasize the importance of post-processing storage studies before releasing cultivars for juice. Published 2015. This article is a U.S. Government work and is in the public domain in the USA.

Influence of Moisture Content and Compression Axis on Physico-mechanical Properties of Shorea robusta Seeds

NASA Astrophysics Data System (ADS)

Shashikumar, C.; Pradhan, R. C.; Mishra, S.

2018-02-01

Shorea robusta (Sal) is mainly harvested and processed for its seed oil, which has diverse application in commercial food and non-food based industries. Before extraction of its oil, seeds undergo into various post-harvest unit operations. Physical and mechanical properties play an important role in the handling and other processing activity. In this study influence of moisture content and compression axis of sal seed on physico-mechanical properties were studied and their application are highlighted. The experiments were conducted at five different moisture levels of 6.38, 10.49, 13.63, 17.64, and 21.95% (d.b) at two different orientations. The first orientation is on major axis (LEN) of the seed, and the other orientation is on intermediate or minor axis (WID), which is right angle to the major axis. It was observed that 68% of sal seeds were of medium size group at initial moisture content of 10.49% (d.b). The mean length and width of sal seed was found to be 26.7 mm and 12.8 mm, respectively. It was found that values of hardness, deformation at hardness, deformation at hardness percentage and energy for rupture were higher in minor axis (WID) as compared to the major axis (LEN). The results provide necessary data that may be useful to engineers, scientists, industries in the design of a suitable post-harvest processing machine.

Harvesting Electricity From Wasted Heat

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schwede, Jared

Scientists as SLAC National Laboratory explain the concept, Photon Enhanced Thermionic Emission (PETE), and how this process can capture more energy from photovoltaic panels by harnessing heat energy from sunlight.

Harvesting Electricity From Wasted Heat

ScienceCinema

Schwede, Jared

2018-01-16

Scientists as SLAC National Laboratory explain the concept, Photon Enhanced Thermionic Emission (PETE), and how this process can capture more energy from photovoltaic panels by harnessing heat energy from sunlight.

50 CFR 679.30 - General CDQ regulations.

Code of Federal Regulations, 2011 CFR

2011-10-01

... visual representation of the qualified applicant's entire organizational structure, including all... narrative description of how the CDQ group intends to harvest and process its CDQ allocations, including a...

Smoke considerations for using fire in maintaining healthy forest ecosystems

Treesearch

Roger D. Ottmar; Mark D. Schaaf; Ernesto Alvarado

1996-01-01

Fire is the single most important ecological disturbance process throughout the interior Pacific Northwest (Mutch and others 1993; Agee 1994). It is also a natural process that helps maintain a diverse ecological landscape. Fire suppression and timber harvesting have drastically altered this process during the past 50 to 90 years. Natural resource specialists generally...

Variation in Carotenoid Content of Kale and Other Vegetables: A Review of Pre- and Post-harvest Effects.

PubMed

Walsh, Rachel P; Bartlett, Hannah; Eperjesi, Frank

2015-11-11

Lutein and zeaxanthin are carotenoids that are selectively taken up into the macula of the eye, where they are thought to protect against the development of age-related macular degeneration. They are obtained from dietary sources, with the highest concentrations found in dark green leafy vegetables, such as kale and spinach. In this Review, compositional variations due to variety/cultivar, stage of maturity, climate or season, farming practice, storage, and processing effects are highlighted. Only data from studies which report on lutein and zeaxanthin content in foods are reported. The main focus is kale; however, other predominantly xanthophyll containing vegetables such as spinach and broccoli are included. A small amount of data about exotic fruits is also referenced for comparison. The qualitative and quantitative composition of carotenoids in fruits and vegetables is known to vary with multiple factors. In kale, lutein and zeaxanthin levels are affected by pre-harvest effects such as maturity, climate, and farming practice. Further research is needed to determine the post-harvest processing and storage effects of lutein and zeaxanthin in kale; this will enable precise suggestions for increasing retinal levels of these nutrients.

Metabolic engineering of Cyanobacteria and microalgae for enhanced production of biofuels and high-value products.

PubMed

Gomaa, M A; Al-Haj, L; Abed, R M M

2016-10-01

A lot of research has been performed on Cyanobacteria and microalgae with the aim to produce numerous biotechnological products. However, native strains have a few shortcomings, like limitations in cultivation, harvesting and product extraction, which prevents reaching optimal production value at lowest costs. Such limitations require the intervention of genetic engineering to produce strains with superior properties. Promising advancements in the cultivation of Cyanobacteria and microalgae have been achieved by improving photosynthetic efficiency through increasing RuBisCO activity and truncation of light-harvesting antennae. Genetic engineering has also contributed to final product extraction by inducing autolysis and product secretory systems, to enable direct product recovery without going through costly extraction steps. In this review, we summarize the different enzymes and pathways that have been targeted thus far for improving cultivation aspects, harvesting and product extraction in Cyanobacteria and microalgae. With synthetic biology advancements, genetically engineered strains can be generated to resolve demanding process issues and achieve economic practicality. This comprehensive overview of gene modifications will be useful to researchers in the field to employ on their strains to increase their yields and improve the economic feasibility of the production process. © 2016 The Society for Applied Microbiology.

A neural-network-based approach to the double traveling salesman problem.

PubMed

Plebe, Alessio; Anile, Angelo Marcello

2002-02-01

The double traveling salesman problem is a variation of the basic traveling salesman problem where targets can be reached by two salespersons operating in parallel. The real problem addressed by this work concerns the optimization of the harvest sequence for the two independent arms of a fruit-harvesting robot. This application poses further constraints, like a collision-avoidance function. The proposed solution is based on a self-organizing map structure, initialized with as many artificial neurons as the number of targets to be reached. One of the key components of the process is the combination of competitive relaxation with a mechanism for deleting and creating artificial neurons. Moreover, in the competitive relaxation process, information about the trajectory connecting the neurons is combined with the distance of neurons from the target. This strategy prevents tangles in the trajectory and collisions between the two tours. Results of tests indicate that the proposed approach is efficient and reliable for harvest sequence planning. Moreover, the enhancements added to the pure self-organizing map concept are of wider importance, as proved by a traveling salesman problem version of the program, simplified from the double version for comparison.

Lead-Free Perovskite Nanowire-Employed Piezopolymer for Highly Efficient Flexible Nanocomposite Energy Harvester.

PubMed

Jeong, Chang Kyu; Baek, Changyeon; Kingon, Angus I; Park, Kwi-Il; Kim, Seung-Hyun

2018-05-01

In the past two decades, mechanical energy harvesting technologies have been developed in various ways to support or power small-scale electronics. Nevertheless, the strategy for enhancing current and charge performance of flexible piezoelectric energy harvesters using a simple and cost-effective process is still a challenging issue. Herein, a 1D-3D (1-3) fully piezoelectric nanocomposite is developed using perovskite BaTiO 3 (BT) nanowire (NW)-employed poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)) for a high-performance hybrid nanocomposite generator (hNCG) device. The harvested output of the flexible hNCG reaches up to ≈14 V and ≈4 µA, which is higher than the current levels of even previous piezoceramic film-based flexible energy harvesters. Finite element analysis method simulations study that the outstanding performance of hNCG devices attributes to not only the piezoelectric synergy of well-controlled BT NWs and within P(VDF-TrFE) matrix, but also the effective stress transferability of piezopolymer. As a proof of concept, the flexible hNCG is directly attached to a hand to scavenge energy using a human motion in various biomechanical frequencies for self-powered wearable patch device applications. This research can pave the way for a new approach to high-performance wearable and biocompatible self-sufficient electronics. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Criteria and Planning Guidance for Ex-Plant Harvesting to Support Subsequent License Renewal

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ramuhalli, Pradeep; Devanathan, Ram; Meyer, Ryan M.

As U.S. nuclear power plants look to subsequent license renewal (SLR) to operate for a 20-year period beyond 60 years, the U.S. Nuclear Regulatory Commission and the industry will be addressing technical issues around the capability of long-lived passive components to meet their functionality objectives. A key challenge will be to better understand likely materials degradation mechanisms in these components and their impacts on component functionality and margins to safety. Research addressing many of the remaining technical gaps in these areas for SLR may greatly benefit from materials sampled from plants (decommissioned or operating). Because of the cost and inefficiencymore » of piecemeal sampling, there is a need for a strategic and systematic approach to sampling materials from structures, systems, and components (SSC) in both operating and decommissioned plants. This document describes a potential approach for sampling (harvesting) materials that focuses on prioritizing materials for sampling using a number of criteria. These criteria are based on an evaluation of technical gaps identified in the literature, research needs to address these technical gaps, and lessons learned from previous harvesting campaigns. The document also describes a process for planning future harvesting campaigns; such a plan would include an understanding of the harvesting priorities, available materials, and the planned use of the materials to address the technical gaps.« less

The effect of water harvesting techniques on runoff, sedimentation, and soil properties.

PubMed

Al-Seekh, Saleh H; Mohammad, Ayed G

2009-07-01

This study addressed the hydrological processes of runoff and sedimentation, soil moisture content, and properties under the effect of different water harvesting techniques (treatments). The study was conducted at three sites, representing environmental condition gradients, located in the southern part of the West Bank. For each treatment, the study evaluated soil chemical and physical properties, soil moisture at 30 cm depth, surface runoff and sedimentation at each site. Results showed that runoff is reduced by 65-85% and sedimentation by 58-69% in stone terraces and semi-circle bunds compared to the control at the semi-humid site. In addition, stone terraces and contour ridges significantly reduced the amount of total runoff by 80% and 73%, respectively, at the arid site. Soil moisture content was significantly increased by water harvesting techniques compared to the control in all treatments at the three study sites. In addition, the difference between the control and the water harvesting structures were higher in the arid and semi-arid areas than in the semi-humid area. Soil and water conservation, via utilization of water harvesting structures, is an effective principle for reducing the negative impact of high runoff intensity and subsequently increasing soil moisture storage from rainfall. Jessour systems in the valley and stone terraces were effective in increasing soil moisture storage, prolonging the growing season for natural vegetation, and decreasing the amount of supplemental irrigation required for growing fruit trees.

WearETE: A Scalable Wearable E-Textile Triboelectric Energy Harvesting System for Human Motion Scavenging

PubMed Central

Li, Xian

2017-01-01

In this paper, we report the design, experimental validation and application of a scalable, wearable e-textile triboelectric energy harvesting (WearETE) system for scavenging energy from activities of daily living. The WearETE system features ultra-low-cost material and manufacturing methods, high accessibility, and high feasibility for powering wearable sensors and electronics. The foam and e-textile are used as the two active tribomaterials for energy harvester design with the consideration of flexibility and wearability. A calibration platform is also developed to quantify the input mechanical power and power efficiency. The performance of the WearETE system for human motion scavenging is validated and calibrated through experiments. The results show that the wearable triboelectric energy harvester can generate over 70 V output voltage which is capable of powering over 52 LEDs simultaneously with a 9 × 9 cm2 area. A larger version is able to lighten 190 LEDs during contact-separation process. The WearETE system can generate a maximum power of 4.8113 mW from hand clapping movements under the frequency of 4 Hz. The average power efficiency can be up to 24.94%. The output power harvested by the WearETE system during slow walking is 7.5248 µW. The results show the possibility of powering wearable electronics during human motion. PMID:29149035

Potential impact of harvesting on the population dynamics of two epiphytic bromeliads

NASA Astrophysics Data System (ADS)

Toledo-Aceves, Tarin; Hernández-Apolinar, Mariana; Valverde, Teresa

2014-08-01

Large numbers of epiphytes are extracted from cloud forests for ornamental use and illegal trade in Latin America. We examined the potential effects of different harvesting regimes on the population dynamics of the epiphytic bromeliads Tillandsia multicaulis and Tillandsia punctulata. The population dynamics of these species were studied over a 2-year period in a tropical montane cloud forest in Veracruz, Mexico. Prospective and retrospective analyses were used to identify which demographic processes and life-cycle stages make the largest relative contribution to variation in population growth rate (λ). The effect of simulated harvesting levels on population growth rates was analysed for both species. λ of both populations was highly influenced by survival (stasis), to a lesser extent by growth, and only slightly by fecundity. Vegetative growth played a central role in the population dynamics of these organisms. The λ value of the studied populations did not differ significantly from unity: T. multicaulis λ (95% confidence interval) = 0.982 (0.897-1.060) and T. punctulata λ = 0.967 (0.815-1.051), suggesting population stability. However, numerical simulation of different levels of extraction showed that λ would drop substantially even under very low (2%) harvesting levels. Matrix analysis revealed that T. multicaulis and T. punctulata populations are likely to decline and therefore commercial harvesting would be unsustainable. Based on these findings, management recommendations are outlined.

The Effect of Water Harvesting Techniques on Runoff, Sedimentation, and Soil Properties

NASA Astrophysics Data System (ADS)

Al-Seekh, Saleh H.; Mohammad, Ayed G.

2009-07-01

This study addressed the hydrological processes of runoff and sedimentation, soil moisture content, and properties under the effect of different water harvesting techniques (treatments). The study was conducted at three sites, representing environmental condition gradients, located in the southern part of the West Bank. For each treatment, the study evaluated soil chemical and physical properties, soil moisture at 30 cm depth, surface runoff and sedimentation at each site. Results showed that runoff is reduced by 65-85% and sedimentation by 58-69% in stone terraces and semi-circle bunds compared to the control at the semi-humid site. In addition, stone terraces and contour ridges significantly reduced the amount of total runoff by 80% and 73%, respectively, at the arid site. Soil moisture content was significantly increased by water harvesting techniques compared to the control in all treatments at the three study sites. In addition, the difference between the control and the water harvesting structures were higher in the arid and semi-arid areas than in the semi-humid area. Soil and water conservation, via utilization of water harvesting structures, is an effective principle for reducing the negative impact of high runoff intensity and subsequently increasing soil moisture storage from rainfall. Jessour systems in the valley and stone terraces were effective in increasing soil moisture storage, prolonging the growing season for natural vegetation, and decreasing the amount of supplemental irrigation required for growing fruit trees.

Broadband Epsilon-near-Zero Reflectors Enhance the Quantum Efficiency of Thin Solar Cells at Visible and Infrared Wavelengths.

PubMed

Labelle, A J; Bonifazi, M; Tian, Y; Wong, C; Hoogland, S; Favraud, G; Walters, G; Sutherland, B; Liu, M; Li, Jun; Zhang, Xixiang; Kelley, S O; Sargent, E H; Fratalocchi, A

2017-02-15

The engineering of broadband absorbers to harvest white light in thin-film semiconductors is a major challenge in developing renewable materials for energy harvesting. Many solution-processed materials with high manufacturability and low cost, such as semiconductor quantum dots, require the use of film structures with thicknesses on the order of 1 μm to absorb incoming photons completely. The electron transport lengths in these media, however, are 1 order of magnitude smaller than this length, hampering further progress with this platform. Herein, we show that, by engineering suitably disordered nanoplasmonic structures, we have created a new class of dispersionless epsilon-near-zero composite materials that efficiently harness white light. Our nanostructures localize light in the dielectric region outside the epsilon-near-zero material with characteristic lengths of 10-100 nm, resulting in an efficient system for harvesting broadband light when a thin absorptive film is deposited on top of the structure. By using a combination of theory and experiments, we demonstrate that ultrathin layers down to 50 nm of colloidal quantum dots deposited atop the epsilon-near-zero material show an increase in broadband absorption ranging from 200% to 500% compared to a planar structure of the same colloidal quantum-dot-absorber average thickness. When the epsilon-near-zero nanostructures were used in an energy-harvesting module, we observed a spectrally averaged 170% broadband increase in the external quantum efficiency of the device, measured at wavelengths between 400 and 1200 nm. Atomic force microscopy and photoluminescence excitation measurements demonstrate that the properties of these epsilon-near-zero structures apply to general metals and could be used to enhance the near-field absorption of semiconductor structures more widely. We have developed an inexpensive electrochemical deposition process that enables scaled-up production of this nanomaterial for large-scale energy-harvesting applications.

Evaluating mallard adaptive management models with time series

USGS Publications Warehouse

Conn, P.B.; Kendall, W.L.

2004-01-01

Wildlife practitioners concerned with midcontinent mallard (Anas platyrhynchos) management in the United States have instituted a system of adaptive harvest management (AHM) as an objective format for setting harvest regulations. Under the AHM paradigm, predictions from a set of models that reflect key uncertainties about processes underlying population dynamics are used in coordination with optimization software to determine an optimal set of harvest decisions. Managers use comparisons of the predictive abilities of these models to gauge the relative truth of different hypotheses about density-dependent recruitment and survival, with better-predicting models giving more weight to the determination of harvest regulations. We tested the effectiveness of this strategy by examining convergence rates of 'predictor' models when the true model for population dynamics was known a priori. We generated time series for cases when the a priori model was 1 of the predictor models as well as for several cases when the a priori model was not in the model set. We further examined the addition of different levels of uncertainty into the variance structure of predictor models, reflecting different levels of confidence about estimated parameters. We showed that in certain situations, the model-selection process favors a predictor model that incorporates the hypotheses of additive harvest mortality and weakly density-dependent recruitment, even when the model is not used to generate data. Higher levels of predictor model variance led to decreased rates of convergence to the model that generated the data, but model weight trajectories were in general more stable. We suggest that predictive models should incorporate all sources of uncertainty about estimated parameters, that the variance structure should be similar for all predictor models, and that models with different functional forms for population dynamics should be considered for inclusion in predictor model! sets. All of these suggestions should help lower the probability of erroneous learning in mallard ABM and adaptive management in general.

Materials Manufactured from 3D Printed Synthetic Biology Arrays

NASA Technical Reports Server (NTRS)

Gentry, Diana; Micks, Ashley

2013-01-01

Many complex, biologically-derived materials have extremely useful properties (think wood or silk), but are unsuitable for space-related applications due to production, manufacturing, or processing limitations. Large-scale ecosystem-based production, such as raising and harvesting trees for wood, is impractical in a self-contained habitat such as a space station or potential Mars colony. Manufacturing requirements, such as the specialized equipment needed to harvest and process cotton, add too much upmass for current launch technology. Cells in nature are already highly specialized for making complex biological materials on a micro scale. We envision combining these strengths with the recently emergent technologies of synthetic biology and 3D printing to create 3D-structured arrays of cells that are bioengineered to secrete different materials in a specified three-dimensional pattern.

Colloidal Engineering for Infrared-Bandgap Solution-Processed Quantum Dot Solar Cells

NASA Astrophysics Data System (ADS)

Kiani, Amirreza

Ever-increasing global energy demand and a diminishing fossil fuel supply have prompted the development of technologies for sustainable energy production. Solar photovoltaic (PV) devices have huge potential for energy harvesting and production since the sun delivers more energy to the earth in one hour than the global population consumes in one year. The solar cell industry is now dominated by silicon PV devices. The cost of silicon modules has decreased substantially over the past two decades and the number of installed silicon PV devices has increased dramatically. There remains a need for emerging solar technologies that can harvest the untapped portion of the solar spectrum and can be integrated on flexible and curved surfaces. This thesis focuses on colloidal quantum dot (CQD) PV devices. CQDs are nanoparticles fabricated using a low-temperature and cost-effective solution technique. These materials suffer from a high density of surface traps derived from the large surface-to-volume ratio of CQD nanoparticles, combined with limited carrier mobility. These result in a short carrier diffusion length, a main limiting factor in CQD solar cell performance. This thesis seeks to address the poor diffusion length in lead sulfide (PbS) CQD films and pave the way for new applications for CQD PV devices in infrared solar harvesting and waste heat recovery. A two-fold reduction in surface trap density is demonstrated using molecular halide treatment. Iodine molecules introduced prior to the film formation replace the otherwise unpassivated surface sulfur atoms. This results in a 35% increase in the diffusion length and enables charge extraction over thicker active layer leading to the world's most efficient CQD PV devices from June 2015 to July 2016 with the certified power conversion efficiency of 9.9%. This represents a 30% increase over the best-certified PCE (7.5%) prior to this thesis. The colloidal engineering highlighted herein enables infrared (IR) solar harvesting for the first time. Addition of short bromothiol ligands during the synthesis significantly reduces the agglomeration of 1 eV bandgap CQDs and maintains efficient charge extraction into the selective electrodes. The devices can augment the performance of the best silicon cells by 7 power points where 0.8 additive power points are demonstrated experimentally. A tailored solution exchanged process developed for 1 eV bandgap CQDs results in air-stable IR PV devices with improved manufacturability. The process utilizes a tailored combination of lead iodide (PbI2) and ammonium acetate for the solution exchange and hexylamine + MEK as the final solvent to yield solar thick films with the filtered (1100 nm and beyond) performance of 0.4%. This thesis pushes the limit of CQD device applications to waste heat recovery. I demonstrate successful harvesting of low energy photons emitted from a hot object by designing and developing the first solution-processed thermophotovoltaic devices. These devices are comprised of 0.7 eV bandgap CQDs that successfully harvest photons emitted from an 800°C heat source.

Fifty-sixth Christmas Bird Count. 147. Southern Dorchester County, Md

USGS Publications Warehouse

Johnson, F.A.; Williams, B.K.; Nichols, J.D.; Hines, J.E.; Kendall, W.L.; Smith, G.W.; Caithamer, David F.

1956-01-01

Summary and Recommendations: We suggest that managers are approaching the limits of their ability to improve waterfowl harvest management, primarily because the information needed to make better decisions is being sacrificed by the current approach to setting regulations. We propose an actively adaptive management strategy in which regulatory decisions play a dominant role in reducing uncertainty about population dynamics. The proposed strategy recognizes 'value' in acquiring knowledge only to the extent that it contributes to the objective of optimizing harvests. To implement this strategy, managers will need: (1) a set of regulatory options, with possible constraints on their use; (2) quantifiable harvest management objectives; (3) a set of models that represent an array of meaningful hypotheses about the effects of regulations on populations; and (4) a measure of credibility (or likelihood) for each model, which can be updated regularly using information from waterfowl monitoring programs. Adaptive optimization is an iterative process in which the harvest-management policy converges over time to one that maximizes harvest under the most appropriate model. At each time step, an optimal regulatory decision is identified based on the state of the system and the model likelihoods. In the next time step, predicted population changes from the alternative models are compared with the actual changes provided by the monitoring program, The likelihoods are increased or decreased to the extent that predicted and actual population changes correspond. These updated likelihoods then are used in setting regulations in the next cycle and the process begins again. This iterative process produces the most informative regulations when uncertainty is prevalent and produces maximum sustainable yields as uncertainty is eliminated. We see no major obstacles to implementing this adaptive strategy, although there are a number of practical considerations. First and foremost, managers should assess the 'value' of learning. Only when there is a high degree of uncertainty about the effects of hunting regulations on population dynamics will the merit of our proposed strategy be evident. We suggest that this almost always will be true given our current understanding of the relationship between annual regulations, survival and population growth in waterfowl. Nonetheless, careful consideration should be given to formulating the set of alternative models. There is no value in distinguishing between models which differ in their mathematical formulation or biological realism, but which suggest similar harvest strategies. We suspect that 'mechanistic' models (i.e., those that attempt to capture the essence of biological processes) will make better candidates for model sets than so-called 'phenomenological' models. Assuming that all model sets include a good approximation of reality, learning rates will be dependent on the quality of monitoring programs. Fortunately, a variety of high-quality monitoring plans for many duck and goose populations of North America, when used with our adaptive approach, should provide new knowledge about population dynamics and response to hunting, and, thus, lead to improved management.

CRITICAL EVALUATION OF THE EFFECTIVENESS OF SEWAGE SLUDGE DISINFECTION AND VECTOR ATTRACTION REDUCTION PROCESSES

EPA Science Inventory

What is the current state of management practices for biosolids production and application, and how can those be made more effective? How effective are Class B disinfection and vector attraction processes, and public access and harvesting restrictions at reducing the public's exp...

A Retrospective Look at Engineering Innovations in the Peanut Industry

USDA-ARS?s Scientific Manuscript database

As research scientists and engineers, we are able to gaze into the future of peanut production and processing because we stand on the shoulders of those who blazed the way before us. We have made tremendous progress in the areas of peanut harvest, curing, transportation, storage, and processing duri...

Effect of high pressure treatment on the survival of Shiga-Toxin producing Escherichia coli in strawberries

USDA-ARS?s Scientific Manuscript database

Most fresh produce, such as strawberries, receives minimal processing and is often eaten raw. Contamination of produce with pathogenic bacteria may occur during growth, harvest, processing, transportation, and storage and presents a serious public health risk. Strawberries have been implicated in ...

Volatile, anthocyanidin, quality and sensory changes in rabbiteye blueberry from whole fruit through pilot plant juice processing.

USDA-ARS?s Scientific Manuscript database

BACKGROUND: High antioxidant content and keen marketing have increased blueberry demand and increased local production which in turn mandates new uses for abundant harvests. Pilot scale processes were employed to investigate the anthocyanidin profiles, qualitative volatile compositions, and sensori...

38 CFR 21.4264 - Farm cooperative courses.

Code of Federal Regulations, 2013 CFR

2013-07-01

... harvesting of crops including fruits, vegetables and pastures, or (ii) The feeding, breeding and managing of... or sale of agricultural products or combinations thereof, such as dairy processing plants, grain...

38 CFR 21.4264 - Farm cooperative courses.

Code of Federal Regulations, 2011 CFR

2011-07-01

... harvesting of crops including fruits, vegetables and pastures, or (ii) The feeding, breeding and managing of... or sale of agricultural products or combinations thereof, such as dairy processing plants, grain...

38 CFR 21.4264 - Farm cooperative courses.

Code of Federal Regulations, 2014 CFR

2014-07-01

... harvesting of crops including fruits, vegetables and pastures, or (ii) The feeding, breeding and managing of... or sale of agricultural products or combinations thereof, such as dairy processing plants, grain...

38 CFR 21.4264 - Farm cooperative courses.

Code of Federal Regulations, 2012 CFR

2012-07-01

... harvesting of crops including fruits, vegetables and pastures, or (ii) The feeding, breeding and managing of... or sale of agricultural products or combinations thereof, such as dairy processing plants, grain...

Food Poisoning

MedlinePlus

... can happen at any point of production: growing, harvesting, processing, storing, shipping or preparing. Cross-contamination — the ... be spread by hand contact, coughing and sneezing. Vibrio vulnificus 1 to 7 days Raw oysters and ...

IMPROVING BIOMASS LOGISTICS COST WITHIN AGRONOMIC SUSTAINABILITY CONSTRAINTS AND BIOMASS QUALITY TARGETS

DOE Office of Scientific and Technical Information (OSTI.GOV)

J. Richard Hess; Kevin L. Kenney; Christopher T. Wright

Equipment manufacturers have made rapid improvements in biomass harvesting and handling equipment. These improvements have increased transportation and handling efficiencies due to higher biomass densities and reduced losses. Improvements in grinder efficiencies and capacity have reduced biomass grinding costs. Biomass collection efficiencies (the ratio of biomass collected to the amount available in the field) as high as 75% for crop residues and greater than 90% for perennial energy crops have also been demonstrated. However, as collection rates increase, the fraction of entrained soil in the biomass increases, and high biomass residue removal rates can violate agronomic sustainability limits. Advancements inmore » quantifying multi-factor sustainability limits to increase removal rate as guided by sustainable residue removal plans, and mitigating soil contamination through targeted removal rates based on soil type and residue type/fraction is allowing the use of new high efficiency harvesting equipment and methods. As another consideration, single pass harvesting and other technologies that improve harvesting costs cause biomass storage moisture management challenges, which challenges are further perturbed by annual variability in biomass moisture content. Monitoring, sampling, simulation, and analysis provide basis for moisture, time, and quality relationships in storage, which has allowed the development of moisture tolerant storage systems and best management processes that combine moisture content and time to accommodate baled storage of wet material based upon “shelf-life.” The key to improving biomass supply logistics costs has been developing the associated agronomic sustainability and biomass quality technologies and processes that allow the implementation of equipment engineering solutions.« less

Analysis of relevant proteins from bone graft harvested using the reamer irrigator and aspirator system (RIA) versus iliac crest (IC) bone graft and RIA waste water.

PubMed

Crist, Brett D; Stoker, Aaron M; Stannard, James P; Cook, James L

2016-08-01

Femoral reaming using a Reamer Irrigator Aspirator (RIA) can produce greater than three liters of waste water per procedure, which contains cells and proteins that could promote bone healing. This purpose of this study was to determine the protein profile of RIA waste water and compare protein synthesis by cells harvested via RIA versus iliac crest (IC) bone graft. Bone graft was collected from 30 patients-15 using RIA from the femur and 15 harvested from the iliac crest. Waste water collected during the RIA procedure was analyzed in 12 patients. Cells from each graft were cultured in monolayer using growth media for 14days and inductive media for the next 14days. Media samples were collected on days 14, 21, and 28. Proteins for analysis were chosen based on their potential in bone healing, pro-inflammatory, and anti-inflammatory processes. Proteins present in RIA waste water indicate the potential for clinical use of this filtrate as an adjunct for enhancing bone production, healing, and remodeling. Similarly, cells cultured from RIA bone graft harvests compared favorably to those from iliac crest bone grafts with respect to their potential to aid in bone healing. RIA waste water has potential to serve as an autogenic and allogenic enhancer for bone healing. Continued development of processing protocols for viable commercial use of the waste water and pre-clinical studies designed to evaluate RIA waste water products for bone healing are ongoing. Copyright © 2016 Elsevier Ltd. All rights reserved.

A novel type of light-harvesting antenna protein of red algal origin in algae with secondary plastids.

PubMed

Sturm, Sabine; Engelken, Johannes; Gruber, Ansgar; Vugrinec, Sascha; Kroth, Peter G; Adamska, Iwona; Lavaud, Johann

2013-07-30

Light, the driving force of photosynthesis, can be harmful when present in excess; therefore, any light harvesting system requires photoprotection. Members of the extended light-harvesting complex (LHC) protein superfamily are involved in light harvesting as well as in photoprotection and are found in the red and green plant lineages, with a complex distribution pattern of subfamilies in the different algal lineages. Here, we demonstrate that the recently discovered "red lineage chlorophyll a/b-binding-like proteins" (RedCAPs) form a monophyletic family within this protein superfamily. The occurrence of RedCAPs was found to be restricted to the red algal lineage, including red algae (with primary plastids) as well as cryptophytes, haptophytes and heterokontophytes (with secondary plastids of red algal origin). Expression of a full-length RedCAP:GFP fusion construct in the diatom Phaeodactylum tricornutum confirmed the predicted plastid localisation of RedCAPs. Furthermore, we observed that similarly to the fucoxanthin chlorophyll a/c-binding light-harvesting antenna proteins also RedCAP transcripts in diatoms were regulated in a diurnal way at standard light conditions and strongly repressed at high light intensities. The absence of RedCAPs from the green lineage implies that RedCAPs evolved in the red lineage after separation from the the green lineage. During the evolution of secondary plastids, RedCAP genes therefore must have been transferred from the nucleus of the endocytobiotic alga to the nucleus of the host cell, a process that involved complementation with pre-sequences allowing import of the gene product into the secondary plastid bound by four membranes. Based on light-dependent transcription and on localisation data, we propose that RedCAPs might participate in the light (intensity and quality)-dependent structural or functional reorganisation of the light-harvesting antennae of the photosystems upon dark to light shifts as regularly experienced by diatoms in nature. Remarkably, in plastids of the red lineage as well as in green lineage plastids, the phycobilisome based cyanobacterial light harvesting system has been replaced by light harvesting systems that are based on members of the extended LHC protein superfamily, either for one of the photosystems (PS I of red algae) or for both (diatoms). In their proposed function, the RedCAP protein family may thus have played a role in the evolutionary structural remodelling of light-harvesting antennae in the red lineage.

Triplet excited state spectra and dynamics of carotenoids from the thermophilic purple photosynthetic bacterium Thermochromatium tepidum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niedzwiedzki, Dariusz; Kobayashi, Masayuki; Blankenship, R. E.

Light-harvesting complex 2 from the anoxygenic phototrophic purple bacterium Thermochromatium tepidum was purified and studied by steady-state absorption, fluorescence and flash photolysis spectroscopy. Steady-state absorption and fluorescence measurements show that carotenoids play a negligible role as supportive energy donors and transfer excitation to bacteriochlorophyll-a with low energy transfer efficiency of ~30%. HPLC analysis determined that the dominant carotenoids in the complex are rhodopin and spirilloxanthin. Carotenoid excited triplet state formation upon direct (carotenoid) or indirect (bacteriochlorophyll-a Q{sub x} band) excitation shows that carotenoid triplets are mostly localized on spirilloxanthin. In addition, no triplet excitation transfer between carotenoids was observed. Suchmore » specific carotenoid composition and spectroscopic results strongly suggest that this organism optimized carotenoid composition in the light-harvesting complex 2 in order to maximize photoprotective capabilities of carotenoids but subsequently drastically suppressed their supporting role in light-harvesting process.« less

Spatially Characterizing Effective Timber Supply

NASA Technical Reports Server (NTRS)

Berry, J. K.; Sailor, J.

1982-01-01

The structure of a computer-oriented cartographic model for assessing roundwood supply for generation of base load electricity is discussed. The model provides an analytical procedure for coupling spatial information of harvesting economics and owner willingness to sell stumpages. Supply is characterized in terms of standing timber; of accessibility considering various harvesting and hauling factors; and of availability as affected by ownership and residential patterns. Factors governing accessibility to timber include effective harvesting distance to haulic roads as modified by barriers and slopes. Haul distance is expressed in units that take into account the relative ease of travel along various road types to a central processing facility. Areas of accessible timber are grouped into spatial units, termed 'timbersheds', of common access to particular haul road segments that belong to unique 'transport zones'. Timber availability considerations include size of ownership parcels, housing density and excluded areas. The analysis techniques are demonstrated for a cartographic data base in western Massachusetts.

The influences of the recycle process on the bacterial community in a pilot scale microalgae raceway pond.

PubMed

Erkelens, Mason; Ball, Andrew S; Lewis, David M

2014-04-01

The use of recycled media has been shown to be a necessary step within the lifecycle of microalgal biofuels for economic sustainability and reducing the water footprint. However the impact of the harvesting of microalgae on the bacterial load of the recycled water has yet to be investigated. Within this study PCR-DGGE and real-time PCR was used to evaluate the bacterial community dynamics within the recycled water following harvest and concentration steps for a pilot scale open pond system (120,000L), which was developed for the production of green crude oil from Tetraselmis sp. in hyper saline water. Two stages were used in the harvesting; Stage 1 electroflocculation, and Stage 2 centrifugation. Electroflocculation was shown to have little effect on the bacterial cell concentration. In contrast bacterial diversity and cell concentration within the centrifugation step was greatly reduced. Copyright © 2014 Elsevier Ltd. All rights reserved.

The use of natural infochemicals for sustainable and efficient harvesting of the microalgae Scenedesmus spp. for biotechnology: insights from a meta-analysis.

PubMed

Roccuzzo, Sebastiana; Beckerman, Andrew P; Pandhal, Jagroop

2016-12-01

Open raceway ponds are regarded as the most economically viable option for large-scale cultivation of microalgae for low to mid-value bio-products, such as biodiesel. However, improvements are required including reducing the costs associated with harvesting biomass. There is now a growing interest in exploiting natural ecological processes within biotechnology. We review how chemical cues produced by algal grazers induce colony formation in algal cells, which subsequently leads to their sedimentation. A statistical meta-analysis of more than 80 studies reveals that Daphnia grazers can induce high levels of colony formation and sedimentation in Scenedesmus obliquus and that these natural, infochemical induced sedimentation rates are comparable to using commercial chemical equivalents. These data suggest that natural ecological interactions can be co-opted in biotechnology as part of a promising, low energy and clean harvesting method for use in large raceway systems.

Systems and methods for harvesting and storing materials produced in a nuclear reactor

DOEpatents

Heinold, Mark R.; Dayal, Yogeshwar; Brittingham, Martin W.

2016-04-05

Systems produce desired isotopes through irradiation in nuclear reactor instrumentation tubes and deposit the same in a robust facility for immediate shipping, handling, and/or consumption. Irradiation targets are inserted and removed through inaccessible areas without plant shutdown and placed in the harvesting facility, such as a plurality of sealable and shipping-safe casks and/or canisters. Systems may connect various structures in a sealed manner to avoid release of dangerous or unwanted matter throughout the nuclear plant, and/or systems may also automatically decontaminate materials to be released. Useable casks or canisters can include plural barriers for containment that are temporarily and selectively removable with specially-configured paths inserted therein. Penetrations in the facilities may limit waste or pneumatic gas escape and allow the same to be removed from the systems without over-pressurization or leakage. Methods include processing irradiation targets through such systems and securely delivering them in such harvesting facilities.

Nitrous oxide emissions from sugarcane straw left on the soil surface in Brazil

NASA Astrophysics Data System (ADS)

Galdos, M. V.; Cerri, C. E.; Carvalho, J. L.; Cerri, C. C.

2012-12-01

In Brazil, the largest exporter of ethanol from sugarcane in the world, burning the dry leaves and tops in order to facilitate the harvest and transportation of the stalks is still a common practice. Burning plant residues causes emissions of greenhouse gases (GHGs) such as CO2, CH4 and N2O, besides the release of charcoal particles into the atmosphere. Due to a combination of pressure from changes in the public opinion and economical reasons, in Brazil sugarcane harvest is changing from a burned into an unburned system. Since manual harvest of sugarcane without burning is not economically feasible, mechanical harvesters have been developed that can take the stalk and leave the residues on the field, forming a mulch, in a system called green cane management. It is expected that 80% of the cane harvested in the main producing regions in Brazil will be harvested without burning by 2014. The conversion from burning sugarcane to green management of sugarcane will have impacts on the biogeochemical cycling of carbon and nitrogen in the plant soil system. The green cane management results in the deposition of large amounts of plant litter on the soil surface after harvest, ranging from 10 to 20 tons per hectare, which impact the whole production process of sugarcane, influencing yields, fertilizer management and application, soil erosion, soil organic matter dynamics as well as greenhouse gas emissions (CO2, N2O, CH4). From a GHG perspective, the conservation of sugarcane residues prevents emissions from the burning process, may promote carbon sequestration in soils and releases nitrogen during the decomposition process replacing the need for, and GHG emissions from, fossil fuel based nitrogen fertilizer sources. Measurements of soil C and N stocks and associated greenhouse gas emissions from the burned and unburned sugarcane systems and in the sugarcane expansion areas are still scarce. Therefore, the main objective of this work was to quantify the nitrous oxide emissions from the sugarcane straw left on the soil surface in Brazil. To do so, we evaluated three rates of sugarcane straw,1/3, 2/3 and 3/3 of the total amount left on the field, which corresponds to 15,226 kg of dry matter per hectare. Nitrous oxide fluxes were measured using a two-piece static chamber (45cm x 70cm) about once a week in the period of August 2010 till July 2012. Gas samples were returned to the laboratory and analyzed using gas chromatography. There were no significant difference between straw doses and the N2O emission rate ranged from -45 to 120 μg N-N2O m-2 h-1. Those emission values are relatively low, which might be related to the low precipitation and soil water content in the first few months after deposition of straw on the field, since the harvest takes place in the dry season in this region. The present text is a piece of contribution in the effort to develop an accurate 'field-to-wheels' assessment of sugarcane-derived ethanol production in Brazil. N2O from straw decomposition is of key relevance, given that the GHG offset value is one of the primary environmental indicators of biofuel product quality.

Measuring quantum effects in photosynthetic light-harvesting complexes with multipartite entanglement

NASA Astrophysics Data System (ADS)

Smyth, Cathal

This thesis is a compilation of studies on delocalization measures, entanglement, and the role of quantum coherence in electronic energy transfer (EET) in light-harvesting complexes. The first two chapters after the introduction provide foundational knowledge of quantum information and light-harvesting, respectively. Chapter 2 introduces concepts from quantum information such as purity, bipartite entanglement and criteria for its measurement. The peripheral light-harvesting complex LH2, isolated from the anoxygenic purple bacterium Rhodopseudomonas acidophila, is employed as model system of interest. This light-harvesting complex, along with a description of the process of light-harvesting, the presence of quantum coherence, and the different models used to simulate EET, are described in chapter 3. In combination these two chapters lay the foundation for chapter 4, a critical assessment of the current measures of delocalization employed in EET studies, their relationship, and overall effectiveness. The conclusion is that entanglement based measures are most effective at measuring quantum effects, and that they can be related to more conventional delocalization measures such as the inverse participation ratio (IPR) by taking into account the entropy of the system under study. All the measures within this chapter are known as bipartite measures, and only measure the strength of correlation between two sites. The fifth chapter presents the core of this thesis. Following a brief introduction to the concept of multipartite entanglement, the development of multipartite delocalization measures that give high-resolution information on quantum coherence in light-harvesting complexes is detailed. In contrast to other measures, these analytical measures can detect many body correlations in large systems undergoing decoherence. We determine that, much like the bipartite entanglement based measures of chapter 4, these measures are also a function of system entropy, and have a similar hierarchial structure as that of multipartite entanglement measures. The final chapter applies these measures to our model LH2 complex, and draws conclusions on the role of bipartite delocalization and multipartite delocalization in EET.

Changes in mineral-associated soil organic carbon pools across a harvested temperate forest chronosequence

NASA Astrophysics Data System (ADS)

MacIntyre, S.; Kellman, L. M.; Gabriel, C. E.; Diochon, A.

2016-12-01

Due to their substantial pool size, changes in mineral soil carbon (C) stores have the potential to generate significant changes in forest soil C budgets. Harvesting represents a significant land use disturbance that can alter soil organic carbon (SOC) stores, with a number of field studies documenting large losses of SOC following clearcut harvesting. However, little is known about how the distribution of SOC changes amongst mineral-associated pools of differing crystallinity following this disturbance. The objective of this study was to quantify changes in mineral-associated SOC pool sizes through depth and time for podzol soils (mineral soil depths of 0-5, 5-10, 10-15, 15-20, 20-35, and 35-50 cm) of a temperate red spruce harvest chronosequence (representing stand ages of 1yr, 15yr, 45yr, 80yr, and 125+yr) in Nova Scotia, Canada. Samples were subjected to a 4-step sequential chemical dissolution to selectively extract C from mineral pools of increasing crystallinity: soluble minerals (deionized water), organo-metal complexes (Na-pyrophosphate), poorly crystalline minerals (hydroxylamine), and crystalline minerals (Na-dithionite HCl). Carbon concentrations were calculated for the solutions acquired during each stage of the selective dissolution process, providing a time series of changes in mineral-associated C through depth and time following harvesting. A loss of SOC from the organo-metal complexed pool following harvesting was observed, particularly in the deeper mineral soil (20-50cm), with this pool dominating the results. In the soluble and poorly crystalline pools, losses of C were also observed from the deeper mineral soil. Of the 5 sites, the 125+yr age class had the highest concentration of SOC associated with crystalline minerals, with the 0-5cm depth stratum holding a large portion of this C. This study may be useful as a model system for understanding how harvesting disturbance alters mineral pool SOM dynamics in humid temperate forest ecosystems.

The relative abundance of predicted genes associated with ammonia-oxidation, nitrate reduction, and biomass decomposition in mineral soil are altered by intensive timber harvest.

NASA Astrophysics Data System (ADS)

Mushinski, R. M.; Zhou, Y.; Gentry, T. J.; Boutton, T. W.

2017-12-01

Forest ecosystems in the southern United States are substantially altered by anthropogenic disturbances such as timber harvest and land conversion, with effects being observed in carbon and nutrient pools as well as biogeochemical processes. Furthermore, the desire to develop renewable energy sources in the form of biomass extraction from logging residues may result in alterations in soil community structure and function. While the impact of forest management on soil physicochemical properties of the region has been studied, its' long-term effect on soil bacterial community composition and metagenomic potential is relatively unknown, especially at deeper soil depths. This study investigates how intensive organic matter removal intensities associated with timber harvest influence decadal-scale alterations in bacterial community structure and functional potential in the upper 1-m of the soil profile, 18 years post-harvest in a Pinus taeda L. forest of eastern Texas. Amplicon sequencing of the 16S rRNA gene was used in conjunction with soil chemical analyses to evaluate treatment-induced differences in community composition and potential environmental drivers of associated change. Furthermore, functional potential was assessed by using amplicon data to make metagenomic predictions. Results indicate that increasing organic matter removal intensity leads to altered community composition and the relative abundance of dominant OTUs annotated to Burkholderia and Aciditerrimonas. The relative abundance of predicted genes associated with dissimilatory nitrate reduction and denitrification were highest in the most intensively harvested treatment while genes involved in nitrification were significantly lower in the most intensively harvested treatment. Furthermore, genes associated with glycosyltransferases were significantly reduced with increasing harvest intensity while polysaccharide lyases increased. These results imply that intensive organic matter removal may create long-term alterations in bacterial community structure with concurrent alterations to mineral soil carbon and nutrient cycling which may have future consequences on forest regeneration and subsequent stand productivity.

Combined Effects of Irrigation Regime, Genotype, and Harvest Stage Determine Tomato Fruit Quality and Aptitude for Processing into Puree

PubMed Central

Arbex de Castro Vilas Boas, Alexandre; Page, David; Giovinazzo, Robert; Bertin, Nadia; Fanciullino, Anne-Laure

2017-01-01

Industry tomatoes are produced under a range of climatic conditions and practices which significantly impact on main quality traits of harvested fruits. However, the quality of tomato intended for processing is currently addressed on delivery through color and Brix only, whereas other traits are overlooked. Very few works provided an integrated view of the management of tomato puree quality throughout the chain. To gain insights into pre- and post-harvest interactions, four genotypes, two water regimes, three maturity stages, and two processes were investigated. Field and glasshouse experiments were conducted near Avignon, France, from May to August 2016. Two irrigation regimes were applied: control plants were irrigated in order to match 100% of evapotranspiration (ETP); water deficit (WD) plants were irrigated as control plants until anthesis of the first flowers, then irrigation was reduced to 60 and 50% ETP in field, and glasshouse respectively. Fruits were collected at three stages during ripening. Their color, fresh weight, dry matter content, and metabolite contents were determined before processing. Pericarp cell size was evaluated in glasshouse only. Two laboratory-scaled processing methods were applied before structural and biochemical analyses of the purees. Results outlined interactive effects between crop and process management. WD hardly reduced yield, but increased dry matter content in the field, in contrast to the glasshouse. The puree viscosity strongly depended on the genotype and the maturity stage, but it was disconnected from fruit dry matter content or Brix. The process impact on puree viscosity strongly depended on water supply during fruit production. Moreover, the lycopene content of fresh fruit may influence puree viscosity. This work opens new perspectives for managing puree quality in the field showing that it was possible to reduce water supply without affecting yield and to improve puree quality. PMID:29051767

Channel catfish

USDA-ARS?s Scientific Manuscript database

This book chapter provides a comprehensive overview of channel catfish aquaculture. Sections include fish biology; commercial culture; culture facilities; production practices; water quality management; nutrition, feeding and feed formulation; infectious diseases; harvesting and processing; and the...

Forest landscape models, a tool for understanding the effect of the large-scale and long-term landscape processes

Treesearch

Hong S. He; Robert E. Keane; Louis R. Iverson

2008-01-01

Forest landscape models have become important tools for understanding large-scale and long-term landscape (spatial) processes such as climate change, fire, windthrow, seed dispersal, insect outbreak, disease propagation, forest harvest, and fuel treatment, because controlled field experiments designed to study the effects of these processes are often not possible (...

Modelling Southern Ocean ecosystems: krill, the food-web, and the impacts of harvesting.

PubMed

Hill, S L; Murphy, E J; Reid, K; Trathan, P N; Constable, A J

2006-11-01

The ecosystem approach to fisheries recognises the interdependence between harvested species and other ecosystem components. It aims to account for the propagation of the effects of harvesting through the food-web. The formulation and evaluation of ecosystem-based management strategies requires reliable models of ecosystem dynamics to predict these effects. The krill-based system in the Southern Ocean was the focus of some of the earliest models exploring such effects. It is also a suitable example for the development of models to support the ecosystem approach to fisheries because it has a relatively simple food-web structure and progress has been made in developing models of the key species and interactions, some of which has been motivated by the need to develop ecosystem-based management. Antarctic krill, Euphausia superba, is the main target species for the fishery and the main prey of many top predators. It is therefore critical to capture the processes affecting the dynamics and distribution of krill in ecosystem dynamics models. These processes include environmental influences on recruitment and the spatially variable influence of advection. Models must also capture the interactions between krill and its consumers, which are mediated by the spatial structure of the environment. Various models have explored predator-prey population dynamics with simplistic representations of these interactions, while others have focused on specific details of the interactions. There is now a pressing need to develop plausible and practical models of ecosystem dynamics that link processes occurring at these different scales. Many studies have highlighted uncertainties in our understanding of the system, which indicates future priorities in terms of both data collection and developing methods to evaluate the effects of these uncertainties on model predictions. We propose a modelling approach that focuses on harvested species and their monitored consumers and that evaluates model uncertainty by using alternative structures and functional forms in a Monte Carlo framework.

Research in biomass production and utilization: Systems simulation and analysis

NASA Astrophysics Data System (ADS)

Bennett, Albert Stewart

There is considerable public interest in developing a sustainable biobased economy that favors support of family farms and rural communities and also promotes the development of biorenewable energy resources. This study focuses on a number of questions related to the development and exploration of new pathways that can potentially move us toward a more sustainable biobased economy. These include issues related to biomass fuels for drying grain, economies-of-scale, new biomass harvest systems, sugar-to-ethanol crop alternatives for the Upper Midwest U.S., biomass transportation, post-harvest biomass processing and double cropping production scenarios designed to maximize biomass feedstock production. The first section of this study considers post-harvest drying of shelled corn grain both at farm-scale and at larger community-scaled installations. Currently, drying of shelled corn requires large amounts of fossil fuel energy. To address future energy concerns, this study evaluates the potential use of combined heat and power systems that use the combustion of corn stover to produce steam for drying and to generate electricity for fans, augers, and control components. Because of the large capital requirements for solid fuel boilers and steam turbines/engines, both farm-scale and larger grain elevator-scaled systems benefit by sharing boiler and power infrastructure with other processes. The second and third sections evaluate sweet sorghum as a possible "sugarcane-like" crop that can be grown in the Upper Midwest. Various harvest systems are considered including a prototype mobile juice harvester, a hypothetical one-pass unit that separates grain heads from chopped stalks and traditional forage/silage harvesters. Also evaluated were post-harvest transportation, storage and processing costs and their influence on the possible use of sweet sorghum as a supplemental feedstock for existing dry-grind ethanol plants located in the Upper Midwest. Results show that the concept of a mobile juice harvester is not economically viable due to low sugar recovery. The addition of front-end stalk processing/pressing equipment into existing ethanol facilities was found to be economically viable when combined with the plants' use of residuals as a natural gas fuel replacement. Because of high loss of fermentable carbohydrates during ensilage, storage of sweet sorghum in bunkers was not found to be economically viable. The fourth section looks at double cropping winter triticale with late-planted summer corn and compares these scenarios to traditional single cropped corn. Double cropping systems show particular promise for co-production of grain and biomass feedstocks and potentially can allow for greater utilization of grain crop residues. However, additional costs and risks associated with producing two crops instead of one could make biomass-double crops less attractive for producers despite productivity advantages. Detailed evaluation and comparisons show double cropped triticale-corn to be at a significant economic disadvantage relative to single crop corn. The cost benefits associated with using less equipment combined with availability of risk mitigating crop insurance and government subsidies will likely limit farmer interest and clearly indicate that traditional single-crop corn will provide greater financial returns to management. To evaluate the various sweet sorghum, single crop corn and double cropped triticale-corn production scenarios, a detailed but generic model was developed. The primary goal of this generic approach was to develop a modeling foundation that can be rapidly adapted, by an experienced user, to describe new and existing biomass and crop production scenarios that may be of interest to researchers. The foundation model allows input of management practices, crop production characteristics and utilizes standardized machinery performance and cost information, including farm-owned machinery and implements, and machinery and farm production operations provided by custom operators. (Abstract shortened by UMI.)

Stress-anneal-induced magnetic anisotropy in highly textured Fe-Ga and Fe-Al magnetostrictive strips for bending-mode vibrational energy harvesters

NASA Astrophysics Data System (ADS)

Park, Jung Jin; Na, Suok-Min; Raghunath, Ganesh; Flatau, Alison B.

2016-05-01

Magnetostrictive Fe-Ga and Fe-Al alloys are promising materials for use in bending-mode vibrational energy harvesters. For this study, 50.8 mm × 5.0 mm × 0.5 mm strips of Fe-Ga and Fe-Al were cut from 0.50-mm thick rolled sheet. An atmospheric anneal was used to develop a Goss texture through an abnormal grain growth process. The anneal lead to large (011) grains that covered over 90% of sample surface area. The resulting highly-textured Fe-Ga and Fe-Al strips exhibited saturation magnetostriction values (λsat = λ∥ - λ⊥) of ˜280 ppm and ˜130 ppm, respectively. To maximize 90° rotation of magnetic moments during bending of the strips, we employed compressive stress annealing (SA). Samples were heated to 500°C, and a 100-150 MPa compressive stress was applied while at 500°C for 30 minutes and while being cooled. The effectiveness of the SA on magnetic moment rotation was inferred by comparing post-SA magnetostriction with the maximum possible yield of rotated magnetic moments, which is achieved when λ∥ = λsat and λ⊥ = 0. The uniformity of the SA along the sample length and the impact of the SA on sensing/energy harvesting performance were then assessed by comparing pre- and post-SA bending-stress-induced changes in magnetization at five different locations along the samples. The SA process with a 150 MPa compressive load improved Fe-Ga actuation along the sample length from 170 to 225 ppm (from ˜60% to within ˜80% of λsat). The corresponding sensing/energy harvesting performance improved by as much as a factor of eight in the best sample, however the improvement was not at all uniform along the sample length. The SA process with a 100 MPa compressive load improved Fe-Al actuation along the sample length from 60 to 73 ppm (from ˜46% to ˜56% of λsat, indicating only a marginally effective SA and suggesting the need for modification of the SA protocol. In spite of this, the SA was effective at improving the sensing/energy harvesting performance by a factor of ˜2.5 in the best sample. As with the Fe-Ga strip, improvement in performance was quite varied along the strip length.

Air curtain development: an energy harvesting solution for hinged doors

NASA Astrophysics Data System (ADS)

Dayal, Vineed; Lee, Soobum

2017-04-01

The paper proposes a fully mechanical air curtain system that will be powered solely by harvested energy from common hinged doors. The average person uses this type of door several times a day with an almost unconscious amount of applied force and effort. This leads to a high potential of energy to be harvested in doorways that see high traffic and frequent operation7 . Frequently opened door entry ways have always been regarded as a major element that causes significant energy loss and contaminated air conditions in buildings6 . Private companies, particularly those with warehouses, have introduced commercial electrical air curtains to block the open entrances from invading cold air11. This project intends to introduce an original design of air curtain which operates fans only when the door opens and closes, by directly converting door motion to fan rotation without any electronic motor or power cable. The air stream created by this device will prevent the transfer of outside air and contaminants. Research will be conducted to determine the most efficient method of harvesting energy from door use, and the prototyping process will be conducted to meet the required performance of current air curtain models.

Adaptation of light-harvesting functions of unicellular green algae to different light qualities.

PubMed

Ueno, Yoshifumi; Aikawa, Shimpei; Kondo, Akihiko; Akimoto, Seiji

2018-05-28

Oxygenic photosynthetic organisms perform photosynthesis efficiently by distributing captured light energy to photosystems (PSs) at an appropriate balance. Maintaining photosynthetic efficiency under changing light conditions requires modification of light-harvesting and energy-transfer processes. In the current study, we examined how green algae regulate their light-harvesting functions in response to different light qualities. We measured low-temperature time-resolved fluorescence spectra of unicellular green algae Chlamydomonas reinhardtii and Chlorella variabilis cells grown under different light qualities. By observing the delayed fluorescence spectra, we demonstrated that both types of green algae primarily modified the associations between light-harvesting chlorophyll protein complexes (LHCs) and PSs (PSII and PSI). Under blue light, Chlamydomonas transferred more energy from LHC to chlorophyll (Chl) located far from the PSII reaction center, while energy was transferred from LHC to PSI via different energy-transfer pathways in Chlorella. Under green light, both green algae exhibited enhanced energy transfer from LHCs to both PSs. Red light induced fluorescence quenching within PSs in Chlamydomonas and LHCs in Chlorella. In Chlorella, energy transfer from PSII to PSI appears to play an important role in balancing excitation between PSII and PSI.

Ochratoxin A on green coffee: influence of harvest and drying processing procedures.

PubMed

Paulino De Moraes, Maria Heloisa; Luchese, Rosa Helena

2003-09-10

Ochratoxin A is a metabolite produced by Aspergillus and Penicillium species that is nephrotoxic and possibly carcinogenic to humans. The aim of this study was to evaluate ochratoxin A contamination in green coffee obtained by different harvesting and drying operations and from fruits of different ripening stages in order to identify hazards. The research was directed to coffees from the highland area of Rio de Janeiro state (Brazil), which is traded in the domestic market. Twenty-two out of 54 samples contained ochratoxin A at levels ranging from 0.3 to 160 microg/kg. Ochatoxin A contamination levels between different ripe stage fruits were not significant (P > 0.05). "Varrição" coffee, consisting of fruits that fell from the tree spontaneously and stayed longer on the ground before being harvested, was the most contaminated. Eleven out of 14 samples of varrição coffee were contaminated. Three out of 10 samples from the northwestern region of the state were positive for ochratoxin at levels ranging from 10.1 to 592 microg/kg. The contaminated samples had in common the fact that they were harvested directly from the soil.

Evaluation of an ergonomics intervention among Nicaraguan coffee harvesting workers.

PubMed

Bao, Stephen; Silverstein, Barbara; Stewart, Kate

2013-01-01

This study evaluated an ergonomics intervention among Nicaraguan coffee harvesting workers, using electromyography and questionnaire survey techniques. Nicaraguan researchers were involved in the study so that they could gain hands-on experience with ergonomics research and applications, and eventually be the specialists conducting ergonomics interventions in Nicaraguan workplaces. Coffee harvesting activities were studied individually and physical hazards were identified accordingly. The results showed decreased muscle loading on the erector spinae muscle and improved comfort reporting in the back region compared to the commonly used baskets. This fulfils the design objective of a newly developed bag that was used in the intervention to reduce physical workload on the coffee harvesting workers. Workers' opinion survey results showed some issues related to the size of the new bag and the lumbar-shoulder belt mechanism. This information can be used in the modification of the bag in the next design. Key players in the process have been identified. Stimulating ergonomics activities in developing countries is suggested by many experts. This study provided an example from coffee workers in Nicaragua. Commonly used job evaluation procedures and physical load quantification methods were used. Ergonomics researchers and practitioners in developing countries may do similar projects on their own in the future.

The long-term effects of planting and harvesting on secondary forest dynamics under climate change in northeastern China

PubMed Central

Yao, Jing; He, Xingyuan; He, Hongshi; Chen, Wei; Dai, Limin; Lewis, Bernard J.; Yu, Lizhong

2016-01-01

Unlike the virgin forest in the Changbaishan Nature Reserve in northeastern China, little research on a landscape scale has been conducted on secondary forests in the region under conditions of a warming climate. This research was undertaken in the upper Hun River region where the vegetation is representative of the typical secondary forest of northeastern China. The spatially explicit forest landscape model LANDIS was utilized to simulate the responses of forest restoration dynamics to anthropogenic disturbance (planting and harvesting) and evaluate the difference of the restoration process under continuation of current climatic conditions and climate warming. The results showed that: (1) The interaction of planting and harvesting has organizational scale effects on the forest. The combination of planting and harvesting policies has significant effects on the overall forest but not on individual species. (2) The area expansion of the historically dominant species Pinus koraiensis is less under climate warming than under continuation of current climatic conditions. These suggests that we should carefully take historically dominant species as the main focus for forest restoration, especially when they are near their natural distribution boundary, because they are probably less capable of successfully adapting to climate change. PMID:26725308

Enhancement of ZnO-based flexible nano generators via a sol-gel technique for sensing and energy harvesting applications

NASA Astrophysics Data System (ADS)

Rajagopalan, P.; Singh, Vipul; Palani, I. A.

2018-03-01

Zinc oxide (ZnO) is a remarkable inorganic semiconductor with exceptional piezoelectric properties compared to other semiconductors. However, in comparison to lead-based hazardous piezoelectric materials, its properties have undesired limitations. Here we report a 5˜6 fold enhancement in piezoelectric features via chemical doping of copper matched to intrinsic ZnO. A flexible piezoelectric nanogenerator (F-PENG) device was fabricated using an unpretentious solution process of spin coating, with other advantages such as robustness, low-weight, improved adhesion, and low cost. The device was used to demonstrate energy harvesting from a standard weight as low as 4 gm and can work as a self-powered mass sensor in a broad range of 4 to 100 gm. The device exhibited a novel energy harvesting technique from a wind source due to its inherent flexibility. At three different velocities (10˜30 m s-1) and five different angles of attack (0˜180 degrees), the device validated the ability to discern different velocities and directions of flow. The device will be useful for mapping the flow of air apart from harvesting the energy. The simulation was done to verify the underlining mechanism of aerodynamics involved.

The long-term effects of planting and harvesting on secondary forest dynamics under climate change in northeastern China.

PubMed

Yao, Jing; He, Xingyuan; He, Hongshi; Chen, Wei; Dai, Limin; Lewis, Bernard J; Yu, Lizhong

2016-01-04

Unlike the virgin forest in the Changbaishan Nature Reserve in northeastern China, little research on a landscape scale has been conducted on secondary forests in the region under conditions of a warming climate. This research was undertaken in the upper Hun River region where the vegetation is representative of the typical secondary forest of northeastern China. The spatially explicit forest landscape model LANDIS was utilized to simulate the responses of forest restoration dynamics to anthropogenic disturbance (planting and harvesting) and evaluate the difference of the restoration process under continuation of current climatic conditions and climate warming. The results showed that: (1) The interaction of planting and harvesting has organizational scale effects on the forest. The combination of planting and harvesting policies has significant effects on the overall forest but not on individual species. (2) The area expansion of the historically dominant species Pinus koraiensis is less under climate warming than under continuation of current climatic conditions. These suggests that we should carefully take historically dominant species as the main focus for forest restoration, especially when they are near their natural distribution boundary, because they are probably less capable of successfully adapting to climate change.

High-performance integrated perovskite and organic solar cells with efficient near-infrared harvesting

NASA Astrophysics Data System (ADS)

Kim, Junghwan; Lee, Kwanghee

2016-09-01

The integration of planar-type perovskite (Eg 1.5 eV) solar cells (PSCs) with a bulk-heterojunction (BHJ) composite comprising a near-infrared (NIR) absorbing conjugated polymer (Eg < 1.4 eV) and a fullerene derivative is a promising approach to overcoming the narrow absorption limit of typical PSCs. Nevertheless, integrated solar cells (ISCs) suffer from low fill factors (FFs) and inefficient NIR harvesting, mainly due to poor charge transport in the BHJ films. Here, we successfully demonstrate highly efficient P-I-N perovskite/BHJ ISCs with an enhanced FF and improved NIR harvesting by introducing a novel n-type semiconducting polymer and a new processing additive into the BHJ films. The optimized ISCs exhibit a power conversion efficiency (PCE) of 16.36%, which far surpasses that of the reference PSCs ( 14.70%) due to the increased current density (Jsc 20.04 mA cm-2) resulting from the additional NIR harvesting. Meanwhile, the optimized ISCs maintain a high FF of 77% and an open-circuit voltage (Voc) of 1.06 V. These results indicate that this approach is a versatile means of overcoming the absorption and theoretical efficiency limits of state-ofthe- art PSCs.

Micro electro-mechanical system piezoelectric cantilever array for a broadband vibration energy harvester.

PubMed

Chun, Inwoo; Lee, Hyun-Woo; Kwon, Kwang-Ho

2014-12-01

Limited energy sources of ubiquitous sensor networks (USNs) such as fuel cells and batteries have grave drawbacks such as the need for replacements and re-charging owing to their short durability and environmental pollution. Energy harvesting which is converting environmental mechanical vibration into electrical energy has been researched with some piezoelectric materials and various cantilever designs to increase the efficiency of energy-harvesting devices. In this study, we focused on an energy-harvesting cantilever with a broadband vibration frequency. We fabricated a lead zirconate titanate (PZT) cantilever array with various Si proof masses on small beams (5.5 mm x 0.5 mm x 0.5 mm). We obtained broadband resonant frequencies ranging between 127 Hz and 136 Hz using a micro electro-mechanical system (MEMS) process. In order to obtain broadband resonant characteristics, the cantilever array was comprised of six cantilevers with different resonant frequencies. We obtained an output power of about 2.461 μW at an acceleration of 0.23 g and a resistance of 4 kΩ. The measured bandwidth of the resonant frequency was approximately 9 Hz (127-136 Hz), which is about six times wider than the bandwidth of a single cantilever.

Enhancement of ZnO-based flexible nano generators via a sol-gel technique for sensing and energy harvesting applications.

PubMed

Rajagopalan, P; Singh, Vipul; Palani, I A

2018-02-01

Zinc oxide (ZnO) is a remarkable inorganic semiconductor with exceptional piezoelectric properties compared to other semiconductors. However, in comparison to lead-based hazardous piezoelectric materials, its properties have undesired limitations. Here we report a 5∼6 fold enhancement in piezoelectric features via chemical doping of copper matched to intrinsic ZnO. A flexible piezoelectric nanogenerator (F-PENG) device was fabricated using an unpretentious solution process of spin coating, with other advantages such as robustness, low-weight, improved adhesion, and low cost. The device was used to demonstrate energy harvesting from a standard weight as low as 4 gm and can work as a self-powered mass sensor in a broad range of 4 to 100 gm. The device exhibited a novel energy harvesting technique from a wind source due to its inherent flexibility. At three different velocities (10∼30 m s -1 ) and five different angles of attack (0∼180 degrees), the device validated the ability to discern different velocities and directions of flow. The device will be useful for mapping the flow of air apart from harvesting the energy. The simulation was done to verify the underlining mechanism of aerodynamics involved.

Effects of Fishing and Fishing Closures on Beach Clams: Experimental Evaluation across Commercially Fished and Non-Fished Beaches before and during Harvesting

PubMed Central

Gray, Charles A.

2016-01-01

Management responses to reconcile declining fisheries typically include closed areas and times to fishing. This study evaluated this strategy for a beach clam fishery by testing the hypothesis that changes in the densities and size compositions of clams from before to during harvesting would differ between commercially fished and non-fished beaches. Sampling was spatially stratified across the swash and dry sand habitats on each of two commercially fished and two non-fished beaches, and temporally stratified across three six-week blocks: before, early and late harvesting. Small-scale spatio-temporal variability in the densities and sizes of clams was prevalent across both habitats and the components of variation were generally greatest at the lowest levels examined. Despite this, differences in the densities and sizes of clams among individual beaches were evident, but there were few significant differences across the commercially fished versus non-fished beaches from before to during harvesting. There was no evidence of reduced densities or truncated size compositions of clams on fished compared to non-fished beaches, contrasting reports of some other organisms in protected areas. This was probably due to a combination of factors, including the current levels of commercial harvests, the movements and other local-scale responses of clams to ecological processes acting independently across individual beaches. The results identify the difficulties in detecting fishing-related impacts against inherent levels of variability in clam populations. Nevertheless, continued experimental studies that test alternate management arrangements may help refine and determine the most suitable strategies for the sustainable harvesting of beach clams, ultimately enhancing the management of sandy beaches. PMID:26731102

Effects of Fishing and Fishing Closures on Beach Clams: Experimental Evaluation across Commercially Fished and Non-Fished Beaches before and during Harvesting.

PubMed

Gray, Charles A

2016-01-01

Management responses to reconcile declining fisheries typically include closed areas and times to fishing. This study evaluated this strategy for a beach clam fishery by testing the hypothesis that changes in the densities and size compositions of clams from before to during harvesting would differ between commercially fished and non-fished beaches. Sampling was spatially stratified across the swash and dry sand habitats on each of two commercially fished and two non-fished beaches, and temporally stratified across three six-week blocks: before, early and late harvesting. Small-scale spatio-temporal variability in the densities and sizes of clams was prevalent across both habitats and the components of variation were generally greatest at the lowest levels examined. Despite this, differences in the densities and sizes of clams among individual beaches were evident, but there were few significant differences across the commercially fished versus non-fished beaches from before to during harvesting. There was no evidence of reduced densities or truncated size compositions of clams on fished compared to non-fished beaches, contrasting reports of some other organisms in protected areas. This was probably due to a combination of factors, including the current levels of commercial harvests, the movements and other local-scale responses of clams to ecological processes acting independently across individual beaches. The results identify the difficulties in detecting fishing-related impacts against inherent levels of variability in clam populations. Nevertheless, continued experimental studies that test alternate management arrangements may help refine and determine the most suitable strategies for the sustainable harvesting of beach clams, ultimately enhancing the management of sandy beaches.

Genetic and biochemical analysis reveals linked QTLs determining natural variation for fruit post-harvest water loss in pepper (Capsicum).

PubMed

Popovsky-Sarid, Sigal; Borovsky, Yelena; Faigenboim, Adi; Parsons, Eugene P; Lohrey, Gregory T; Alkalai-Tuvia, Sharon; Fallik, Elazar; Jenks, Matthew A; Paran, Ilan

2017-02-01

Molecular markers linked to QTLs controlling post-harvest fruit water loss in pepper may be utilized to accelerate breeding for improved shelf life and inhibit over-ripening before harvest. Bell pepper (Capsicum annuum L.) is an important vegetable crop world-wide. However, marketing is limited by the relatively short shelf life of the fruit due to water loss and decay that occur during prolonged storage. Towards breeding pepper with reduced fruit post-harvest water loss (PWL), we studied the genetic, physiological and biochemical basis for natural variation of PWL. We performed quantitative trait locus (QTL) mapping of fruit PWL in multiple generations of an interspecific cross of pepper, which resulted in the identification of two linked QTLs on chromosome 10 that control the trait. We further developed near-isogenic lines (NILs) for characterization of the QTL effects. Transcriptome analysis of the NILs allowed the identification of candidate genes associated with fruit PWL-associated traits such as cuticle biosynthesis, cell wall metabolism and fruit ripening. Significant differences in PWL between the NILs in the immature fruit stage, differentially expressed cuticle-associated genes and differences in the content of specific chemical constituents of the fruit cuticle, indicated a likely influence of cuticle composition on the trait. Reduced PWL in the NILs was associated with delayed over-ripening before harvest, low total soluble solids before storage, and reduced fruit softening after storage. Our study enabled a better understanding of the genetic and biological processes controlling natural variation in fruit PWL in pepper. Furthermore, the genetic materials and molecular markers developed in this study may be utilized to breed peppers with improved shelf life and inhibited over-ripening before harvest.

Ammonia oxidizing archaea are the predominant nitrifiers in disturbed and undisturbed southern US pine forests

NASA Astrophysics Data System (ADS)

Mushinski, R. M.; Boutton, T. W.; Gentry, T. J.; Dorosky, R. J.

2016-12-01

The rate-limiting step in nitrification, ammonia oxidation, is performed by both ammonia oxidizing bacteria (AOB) and archaea (AOA); however, reports on the relative contribution of each of these groups to forest soil nitrification has varied. We coupled qPCR and next generation sequencing of the amoA gene to a whole-soil assay that stimulates nitrification and allows for the discrimination of AOA- from AOB-activity using 1-octyne, which inhibits the activity of the bacterial ammonia monooxygenase. Soils, to a depth of 1 meter, were collected from replicated (n = 3) loblolly pine (Pinus taeda L.) stands subjected to three different intensities of timber harvest (i.e., unharvested old growth stands, bole-only harvest stands, and whole-tree harvest + forest floor removal stands). The abundance of both bacterial and archaeal amoA were influenced by harvest method and soil depth; furthermore, archaeal amoA was 13x more abundant than bacterial amoA, across all soil depths. Sequencing and subsequent annotation of the ammonia oxidizing community revealed that the AOA were dominated by Crenarchaeota and AOB were dominated by Nitrosospira. Surface mineral soils (0-10 cm) amended with 1-octyne revealed that approximately 67-86% of total nitrification can be attributable to AOA activity. The highest rates of nitrification (total and 1-octyne resistant) occurred in the soils taken from the unharvested reference stands which were significantly greater than harvested stands. We can conclude that in this pine forest system, AOA dominates AOB in regards to amoA copy number and ammonia oxidizing activity. Not only is this study one of the first to investigate the ammonia-oxidizing population in southern pine forests, but also illustrates that timber harvest can lead to long-term alterations in nitrogen cycle processes.

Evidence from in vivo manipulations of lipid composition in mutants that the delta 3-trans-hexadecenoic acid-containing phosphatidylglycerol is involved in the biogenesis of the light-harvesting chlorophyll a/b-protein complex of Chlamydomonas reinhardtii.

PubMed

Dubertret, G; Mirshahi, A; Mirshahi, M; Gerard-Hirne, C; Tremolieres, A

1994-12-01

The phosphatidylglycerol containing the unusual delta 3-trans hexadecenoic fatty acid is specifically found in photosynthetic membranes of eukaryotic organisms. Its involvement in the biogenesis and the structure of the light-harvesting chlorophyll a/b-protein complex has been evidenced by in vivo targeting this lipid to photosynthetic membranes of Chlamydomonas reinhardtii mutants lacking this lipid. In the mf1 and mf2 mutants, this deficiency results in (a) the absence of the oligomeric light-harvesting complex of photosystem 2; (b) an extensive destacking of thylakoid membranes; (c) a very low 77-K fluorescence emission in the photosystem-2 region. We show in this paper that these deficiencies result from modifications in the pigment and polypeptide compositions of the photosystem-2 light-harvesting complex; it contains less chlorophyll b and some of its constitutive polypeptides are absent or reduced in amount, while immunologically related polypeptides of lower molecular mass accumulate. The direct involvement of the lack of trans-C16: 1-phosphatidylglycerol in these deficiencies is evidenced by the partial restoration of normal characteristics of the light-harvesting complex (pigment and polypeptide composition, oligomerization) after liposome-mediated, in vivo incorporation of this lipid into the photosynthetic membranes of the mf2 mutant. Trans-C16:1-phosphatidylglycerol, therefore, is involved in the biogenesis of the photosystem-2 light-harvesting chlorophyll a/b-protein complex through a mechanism that may prevent degradation processes. Its contribution to the structural conformation of neosynthesized monomers and to their organization into stable oligomeric form is discussed.