14 CFR 27.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious object except as provided for in § 27.562(c)(5). A shoulder harness (upper torso restraint), in... serious injury in an emergency landing as a result of the static inertial load factors specified in § 27...

14 CFR 27.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious object except as provided for in § 27.562(c)(5). A shoulder harness (upper torso restraint), in... serious injury in an emergency landing as a result of the static inertial load factors specified in § 27...

14 CFR 27.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious object except as provided for in § 27.562(c)(5). A shoulder harness (upper torso restraint), in... serious injury in an emergency landing as a result of the static inertial load factors specified in § 27...

42 CFR 84.173 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Harnesses; installation and construction; minimum... SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE... construction; minimum requirements. (a) Each respirator shall, where necessary, be equipped with a suitable...

42 CFR 84.1133 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Harnesses; installation and construction; minimum requirements. 84.1133 Section 84.1133 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.1133 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Harnesses; installation and construction; minimum requirements. 84.1133 Section 84.1133 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.1133 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Harnesses; installation and construction; minimum requirements. 84.1133 Section 84.1133 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.1133 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Harnesses; installation and construction; minimum requirements. 84.1133 Section 84.1133 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.1133 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Harnesses; installation and construction; minimum requirements. 84.1133 Section 84.1133 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.116 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Harnesses; installation and construction; minimum requirements. 84.116 Section 84.116 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.116 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Harnesses; installation and construction; minimum requirements. 84.116 Section 84.116 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.116 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Harnesses; installation and construction; minimum requirements. 84.116 Section 84.116 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.116 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Harnesses; installation and construction; minimum requirements. 84.116 Section 84.116 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.116 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Harnesses; installation and construction; minimum requirements. 84.116 Section 84.116 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE...

42 CFR 84.73 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 42 Public Health 1 2011-10-01 2011-10-01 false Harnesses; installation and construction; minimum requirements. 84.73 Section 84.73 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self...

42 CFR 84.73 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 42 Public Health 1 2012-10-01 2012-10-01 false Harnesses; installation and construction; minimum requirements. 84.73 Section 84.73 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self...

42 CFR 84.73 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 42 Public Health 1 2013-10-01 2013-10-01 false Harnesses; installation and construction; minimum requirements. 84.73 Section 84.73 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self...

42 CFR 84.73 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 42 Public Health 1 2014-10-01 2014-10-01 false Harnesses; installation and construction; minimum requirements. 84.73 Section 84.73 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self...

42 CFR 84.73 - Harnesses; installation and construction; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Harnesses; installation and construction; minimum requirements. 84.73 Section 84.73 Public Health PUBLIC HEALTH SERVICE, DEPARTMENT OF HEALTH AND HUMAN SERVICES OCCUPATIONAL SAFETY AND HEALTH RESEARCH AND RELATED ACTIVITIES APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Self...

14 CFR 29.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... serious injury in an emergency landing as a result of the inertial factors specified in § 29.561(b) and dynamic conditions specified in § 29.562. (b) Each occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious...

14 CFR 29.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... serious injury in an emergency landing as a result of the inertial factors specified in § 29.561(b) and dynamic conditions specified in § 29.562. (b) Each occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious...

14 CFR 29.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... serious injury in an emergency landing as a result of the inertial factors specified in § 29.561(b) and dynamic conditions specified in § 29.562. (b) Each occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious...

14 CFR 29.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... serious injury in an emergency landing as a result of the inertial factors specified in § 29.561(b) and dynamic conditions specified in § 29.562. (b) Each occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the head from contacting any injurious...

14 CFR 23.2 - Special retroactive requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... airplane for entry into the United States must provide a safety belt and shoulder harness for each forward- or aft-facing seat which will protect the occupant from serious head injury when subjected to the... safety belt and shoulder harness installed. (b) Each shoulder harness installed at a flight crewmember...

14 CFR 23.2 - Special retroactive requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... airplane for entry into the United States must provide a safety belt and shoulder harness for each forward- or aft-facing seat which will protect the occupant from serious head injury when subjected to the... safety belt and shoulder harness installed. (b) Each shoulder harness installed at a flight crewmember...

14 CFR 23.2 - Special retroactive requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... airplane for entry into the United States must provide a safety belt and shoulder harness for each forward- or aft-facing seat which will protect the occupant from serious head injury when subjected to the... safety belt and shoulder harness installed. (b) Each shoulder harness installed at a flight crewmember...

14 CFR 23.2 - Special retroactive requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... airplane for entry into the United States must provide a safety belt and shoulder harness for each forward- or aft-facing seat which will protect the occupant from serious head injury when subjected to the... safety belt and shoulder harness installed. (b) Each shoulder harness installed at a flight crewmember...

14 CFR 23.2 - Special retroactive requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... airplane for entry into the United States must provide a safety belt and shoulder harness for each forward- or aft-facing seat which will protect the occupant from serious head injury when subjected to the... safety belt and shoulder harness installed. (b) Each shoulder harness installed at a flight crewmember...

14 CFR 29.2 - Special retroactive requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the... equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (a) Each occupant's seat must have a combined safety belt and shoulder harness with...

14 CFR 29.2 - Special retroactive requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the... equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (a) Each occupant's seat must have a combined safety belt and shoulder harness with...

14 CFR 29.2 - Special retroactive requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the... equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (a) Each occupant's seat must have a combined safety belt and shoulder harness with...

14 CFR 29.2 - Special retroactive requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the... equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (a) Each occupant's seat must have a combined safety belt and shoulder harness with...

14 CFR 29.2 - Special retroactive requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... be protected from serious head injury by a safety belt plus a shoulder harness that will prevent the... equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (a) Each occupant's seat must have a combined safety belt and shoulder harness with...

Microsputterer with integrated ion-drag focusing for additive manufacturing of thin, narrow conductive lines

NASA Astrophysics Data System (ADS)

Kornbluth, Y. S.; Mathews, R. H.; Parameswaran, L.; Racz, L. M.; Velásquez-García, L. F.

2018-04-01

We report the design, modelling, and proof-of-concept demonstration of a continuously fed, atmospheric-pressure microplasma metal sputterer that is capable of printing conductive lines narrower than the width of the target without the need for post-processing or lithographic patterning. Ion drag-induced focusing is harnessed to print narrow lines; the focusing mechanism is modelled via COMSOL Multiphysics simulations and validated with experiments. A microplasma sputter head with gold target is constructed and used to deposit imprints with minimum feature sizes as narrow as 9 µm, roughness as small as 55 nm, and electrical resistivity as low as 1.1 µΩ · m.

42 CFR 84.151 - Harness test; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

... concrete floor without disarranging the harness or exerting a pull on the facepiece. (5) The arrangement... manner that prevents a pull equivalent to dragging the maximum length of the hose over a concrete floor...

The pubo-femoral distance decreases with Pavlik harness treatment for developmental dysplasia of the hip in newborns.

PubMed

Maranho, Daniel Augusto; Donati, Felipe Nunes; Dalto, Vitor Faeda; Nogueira-Barbosa, Marcello Henrique

2017-09-01

To evaluate the evolution of the ultrasonographic pubo-femoral distance (PFD) before and after Pavlik harness treatment for developmental dysplasia of the hip (DDH) in newborns. Twenty-five patients (16.7 ± 10.4 days; 19 females, six males) diagnosed with DDH and treated using the Pavlik harness were included. Eighteen patients had bilateral, and seven unilateral DDH, with a total of 43 dysplastic hips. The seven non-dysplastic hips in unilateral cases were used for comparison. The PFD was measured in the coronal and axial planes with the hip flexed to approximately 90°, before and after an average of 93 days of treatment. The femoral head coverage was assessed in the coronal plane, and correlated with PFD values. In dysplastic hips, the mean PFD decreased from 6.1 ± 1.8 mm to 3.0 ± 0.7 mm in the axial (adjusted difference, 2.9 mm; p < 0.01), and from 5.9 ± 2.0 to 3.0 ± 0.6 mm in the coronal plane (adjusted difference 2.7 mm; p < 0.01). The femoral head coverage increased from 30.8 to 62.1%, and the mean differences of femoral head coverage and PFD were significantly correlated (p < 0.001). There was no difference between treated dysplastic and non-dysplastic hips. There was high intra- and inter-observer agreement for PFD measurements. The PFD decreased significantly after DDH treatment using the Pavlik harness in newborns, and showed significant correlation with the femoral head coverage improvement. PFD might be a reliable tool for monitoring DDH treatment in newborns treated using the Pavlik harness.

14 CFR 91.313 - Restricted category civil aircraft: Operating limitations.

Code of Federal Regulations, 2014 CFR

2014-01-01

...-category civil airplane manufactured after July 18, 1978, unless an approved shoulder harness is installed for each front seat. The shoulder harness must be designed to protect each occupant from serious head injury when the occupant experiences the ultimate inertia forces specified in § 23.561(b)(2) of this...

14 CFR 91.313 - Restricted category civil aircraft: Operating limitations.

Code of Federal Regulations, 2012 CFR

2012-01-01

...-category civil airplane manufactured after July 18, 1978, unless an approved shoulder harness is installed for each front seat. The shoulder harness must be designed to protect each occupant from serious head injury when the occupant experiences the ultimate inertia forces specified in § 23.561(b)(2) of this...

14 CFR 27.2 - Special retroactive requirements.

Code of Federal Regulations, 2011 CFR

2011-01-01

... occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will... seat is equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (1) Each occupant's seat must have a combined safety belt and shoulder...

14 CFR 27.2 - Special retroactive requirements.

Code of Federal Regulations, 2013 CFR

2013-01-01

... occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will... seat is equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (1) Each occupant's seat must have a combined safety belt and shoulder...

14 CFR 91.313 - Restricted category civil aircraft: Operating limitations.

Code of Federal Regulations, 2010 CFR

2010-01-01

...-category civil airplane manufactured after July 18, 1978, unless an approved shoulder harness is installed for each front seat. The shoulder harness must be designed to protect each occupant from serious head injury when the occupant experiences the ultimate inertia forces specified in § 23.561(b)(2) of this...

14 CFR 27.2 - Special retroactive requirements.

Code of Federal Regulations, 2014 CFR

2014-01-01

... occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will... seat is equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (1) Each occupant's seat must have a combined safety belt and shoulder...

14 CFR 27.2 - Special retroactive requirements.

Code of Federal Regulations, 2012 CFR

2012-01-01

... occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will... seat is equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (1) Each occupant's seat must have a combined safety belt and shoulder...

14 CFR 91.313 - Restricted category civil aircraft: Operating limitations.

Code of Federal Regulations, 2011 CFR

2011-01-01

...-category civil airplane manufactured after July 18, 1978, unless an approved shoulder harness is installed for each front seat. The shoulder harness must be designed to protect each occupant from serious head injury when the occupant experiences the ultimate inertia forces specified in § 23.561(b)(2) of this...

14 CFR 27.2 - Special retroactive requirements.

Code of Federal Regulations, 2010 CFR

2010-01-01

... occupant must be protected from serious head injury by a safety belt plus a shoulder harness that will... seat is equipped with a safety belt and shoulder harness that meets the requirements of paragraphs (a), (b), and (c) of this section. (1) Each occupant's seat must have a combined safety belt and shoulder...

14 CFR 91.313 - Restricted category civil aircraft: Operating limitations.

Code of Federal Regulations, 2013 CFR

2013-01-01

...-category civil airplane manufactured after July 18, 1978, unless an approved shoulder harness is installed for each front seat. The shoulder harness must be designed to protect each occupant from serious head injury when the occupant experiences the ultimate inertia forces specified in § 23.561(b)(2) of this...

Compliant Walker

NASA Technical Reports Server (NTRS)

Kerley, James J.; Eklund, Wayne; Crane, Alan

1992-01-01

Walker supports person with limited use of legs and back. Enables person to stand upright, move with minimum load, and rest at will taking weight off legs. Consists of wheeled frame with body harness connected compliantly to side structures. Harness supports wearer upright when wearer relaxes and takes weight off lower extremities. Assumes partial to full body weight at user's discretion.

Harnessing the microbiome to reduce Fusarium head blight

USDA-ARS?s Scientific Manuscript database

Fusarium graminearum (Fg), the primary fungal pathogen responsible for Fusarium head blight (FHB), reduces crop yield and contaminates grain with trichothecene mycotoxins that are deleterious to plant, human and animal health. In this presentation, we will discuss two different research projects tha...

Human Tolerance to Rapidly Applied Accelerations: A Summary of the Literature

NASA Technical Reports Server (NTRS)

Eiband, A. Martin

1959-01-01

The literature is surveyed to determine human tolerance to rapidly applied accelerations. Pertinent human and animal experiments applicable to space flight and to crash impact forces are analyzed and discussed. These data are compared and presented on the basis of a trapezoidal pulse. The effects of body restraint and of acceleration direction, onset rate, and plateau duration on the maximum tolerable and survivable rapidly applied accelerations are shown. Results of the survey indicate that adequate torso and extremity restraint is the primary variable in tolerance to rapidly applied accelerations. The harness, or restraint system, must be arranged to transmit the major portion of the accelerating force directly to the pelvic structure and not via the vertebral column. When the conditions of adequate restraint have been met, then the other variables, direction, magnitude, and onset rate of rapidly applied accelerations, govern maximum tolerance and injury limits. The results also indicate that adequately stressed aft-faced passenger seats offer maximum complete body support with minimum objectionable harnessing. Such a seat, whether designed for 20-, 30-, or 40-G dynamic loading, would include lap strap, chest (axillary) strap, and winged-back seat to increase headward and lateral G protection, full-height integral head rest, arm rests (load-bearing) with recessed hand-holds and provisions to prevent arms from slipping either laterally or beyond the seat back, and leg support to keep the legs from being wedged under the seat. For crew members and others whose duties require forward-facing seats, maximum complete body support requires lap, shoulder, and thigh straps, lap-belt tie-down strap, and full-height seat back with integral head support.

An examination of shoulder kinematics and kinetics when using a commercial trunk harness while sheep shearing.

PubMed

Gregory, Diane E; Milosavljevic, Stephan; Pal, Poonam; Callaghan, Jack P

2008-01-01

Sheep shearing is a very physically demanding occupation, especially on the low back, such that many commercial harnesses have been developed to help reduce the load on the back. Such harnesses have been shown to significantly reduce peak and cumulative low back loads; however, the effect that these harnesses have on the shoulders, which are also highly involved during sheep shearing, has not been previously examined. The purpose of this study was to examine the shoulder postures and cumulative shoulder moments of 12 New Zealand sheep shearers. The use of the trunk harness reduced the percentage of time spent in shoulder flexion greater than 90 degrees and the time spent in shoulder abduction greater than 45 degrees as well as reduced the cumulative net joint flexor, abductor, and adductor shoulder moments by a minimum of 21%, 14%, and 42%, respectively. Therefore, the use of a commercial trunk harness to reduce low back injury may also help to reduce the risk of shoulder injury while sheep shearing.

Automatic recognition of falls in gait-slip training: Harness load cell based criteria.

PubMed

Yang, Feng; Pai, Yi-Chung

2011-08-11

Over-head-harness systems, equipped with load cell sensors, are essential to the participants' safety and to the outcome assessment in perturbation training. The purpose of this study was to first develop an automatic outcome recognition criterion among young adults for gait-slip training and then verify such criterion among older adults. Each of 39 young and 71 older subjects, all protected by safety harness, experienced 8 unannounced, repeated slips, while walking on a 7m walkway. Each trial was monitored with a motion capture system, bilateral ground reaction force (GRF), harness force, and video recording. The fall trials were first unambiguously indentified with careful visual inspection of all video records. The recoveries without balance loss (in which subjects' trailing foot landed anteriorly to the slipping foot) were also first fully recognized from motion and GRF analyses. These analyses then set the gold standard for the outcome recognition with load cell measurements. Logistic regression analyses based on young subjects' data revealed that the peak load cell force was the best predictor of falls (with 100% accuracy) at the threshold of 30% body weight. On the other hand, the peak moving average force of load cell across 1s period, was the best predictor (with 100% accuracy) separating recoveries with backward balance loss (in which the recovery step landed posterior to slipping foot) from harness assistance at the threshold of 4.5% body weight. These threshold values were fully verified using the data from older adults (100% accuracy in recognizing falls). Because of the increasing popularity in the perturbation training coupling with the protective over-head-harness system, this new criterion could have far reaching implications in automatic outcome recognition during the movement therapy. Copyright © 2011 Elsevier Ltd. All rights reserved.

AUTOMATIC RECOGNITION OF FALLS IN GAIT-SLIP: A HARNESS LOAD CELL BASED CRITERION

PubMed Central

Yang, Feng; Pai, Yi-Chung

2012-01-01

Over-head-harness systems, equipped with load cell sensors, are essential to the participants’ safety and to the outcome assessment in perturbation training. The purpose of this study was to first develop an automatic outcome recognition criterion among young adults for gait-slip training and then verify such criterion among older adults. Each of 39 young and 71 older subjects, all protected by safety harness, experienced 8 unannounced, repeated slips, while walking on a 7-m walkway. Each trial was monitored with a motion capture system, bilateral ground reaction force (GRF), harness force and video recording. The fall trials were first unambiguously indentified with careful visual inspection of all video records. The recoveries without balance loss (in which subjects’ trailing foot landed anteriorly to the slipping foot) were also first fully recognized from motion and GRF analyses. These analyses then set the gold standard for the outcome recognition with load cell measurements. Logistic regression analyses based on young subjects’ data revealed that peak load cell force was the best predictor of falls (with 100% accuracy) at the threshold of 30% body weight. On the other hand, the peak moving average force of load cell across 1-s period, was the best predictor (with 100% accuracy) separating recoveries with backward balance loss (in which the recovery step landed posterior to slipping foot) from harness assistance at the threshold of 4.5% body weight. These threshold values were fully verified using the data from older adults (100% accuracy in recognizing falls). Because of the increasing popularity in the perturbation training coupling with the protective over-head-harness system, this new criterion could have far reaching implications in automatic outcome recognition during the movement therapy. PMID:21696744

14 CFR 25.785 - Seats, berths, safety belts, and harnesses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... must be protected from head injury by a safety belt and an energy absorbing rest that will support the... energy absorbing rest that will support the arms, shoulders, head, and spine. (e) Each berth must be... § 25.561. Berths must be free from corners and protuberances likely to cause injury to a person...

14 CFR 25.785 - Seats, berths, safety belts, and harnesses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... must be protected from head injury by a safety belt and an energy absorbing rest that will support the... energy absorbing rest that will support the arms, shoulders, head, and spine. (e) Each berth must be... § 25.561. Berths must be free from corners and protuberances likely to cause injury to a person...

14 CFR 25.785 - Seats, berths, safety belts, and harnesses.

Code of Federal Regulations, 2010 CFR

2010-01-01

... must be protected from head injury by a safety belt and an energy absorbing rest that will support the... energy absorbing rest that will support the arms, shoulders, head, and spine. (e) Each berth must be... § 25.561. Berths must be free from corners and protuberances likely to cause injury to a person...

14 CFR 25.785 - Seats, berths, safety belts, and harnesses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... must be protected from head injury by a safety belt and an energy absorbing rest that will support the... energy absorbing rest that will support the arms, shoulders, head, and spine. (e) Each berth must be... § 25.561. Berths must be free from corners and protuberances likely to cause injury to a person...

14 CFR 25.785 - Seats, berths, safety belts, and harnesses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... must be protected from head injury by a safety belt and an energy absorbing rest that will support the... energy absorbing rest that will support the arms, shoulders, head, and spine. (e) Each berth must be... § 25.561. Berths must be free from corners and protuberances likely to cause injury to a person...

49 CFR 179.220-6 - Thickness of plates.

Code of Federal Regulations, 2010 CFR

2010-10-01

... heads; P = Minimum required bursting pressure in psig; S = Minimum tensile strength of plate material in p.s.i. as prescribed in AAR Specifications for Tank Cars, appendix M, Table M1; t = Minimum... seamless heads; L = Main inside radius to which head is dished, measured on concave side in inches; P...

Results of upper airway radiography and ultrasonography predict dynamic laryngeal collapse in affected horses.

PubMed

Fjordbakk, C T; Chalmers, H J; Holcombe, S J; Strand, E

2013-11-01

The pathogenesis of dynamic bilateral laryngeal collapse (DLC) associated with poll flexion is unknown. Diagnosis is dependent upon exercise endoscopy while replicating the flexed head position harness racehorses experience during racing. To describe the effects of poll flexion on rostrocaudal laryngeal positioning and laryngeal lumen width in resting horses diagnosed with DLC compared to controls, and to establish diagnostic criteria for DLC by use of diagnostic imaging. Case-control study. Fifty harness racehorses were prospectively included in the study: 25 cases diagnosed with DLC by treadmill endoscopy and 25 controls in which treadmill endoscopy revealed no abnormal findings. Laryngeal radiography and ultrasonography were obtained in neutral and flexed head positions. Laryngeal positioning and laryngohyoid conformation were compared between the groups and head positions. Poll flexion induced a greater rostral advancement of the larynx in relation to the hyoid apparatus in resting harness racehorses affected with DLC compared to controls (P = 0.007). At the level of the vocal folds, poll flexion resulted in a smaller laryngeal lumen width in horses affected with DLC compared to controls (P = 0.04). Horses were significantly more likely to be affected with DLC when the thyrohyoid bone to thyroid cartilage distance was ≥12 mm in poll flexion (odds ratio 21.3, 95% confidence interval 3.65-124.8, P = 0.004) and when laryngeal lumen width at the level of the vocal folds was less in poll flexion than in the neutral head position (odds ratio 8.4; 95% confidence interval 1.6-44.1, P = 0.012). In DLC horses, poll flexion advanced the larynx more rostrally and resulted in a decreased airway lumen width compared to control horses. Laryngeal ultrasound and radiography may facilitate the diagnosis of DLC at rest. © 2013 EVJ Ltd.

Suspension restraint - Induced hypokinesia and antiorthostasis as a simulation of weightlessness

NASA Technical Reports Server (NTRS)

Musacchia, X. J.; Steffen, J. M.; Deavers, D. R.

1982-01-01

Muscle, renal, fluid and electrolyte responses were measured in suspended rats; the hind limbs are non-load bearing and the front limbs can be used for feeding and grooming. Hind limb hypokinesia reverses after removal from the suspension harness. This suspension system is adjustable for a head-down tilt to produce antiorthostatic responses which are also reversible. Responses to hypokinesia or antiorthostatic hypokinesia for up to 14 days were measured, e.g., muscle atrophy: soleus greater than gastrocnemius equals plantaris greater than extensor digitorum longus, kaliuresis, and increased excretion of urea, NH3, and 3 methylhistidine. Muscle protein loss, a response to a reduction in RNA, is also reversible. A head-down tilt for 7-14 days results in diuresis and natriuresis. These changes are reversed within 24 hours after removal from the restraint harness. Physiological effects of suspension restraint can be used to simulate and predict responses to microgravity exposure.

Red Plague Control Plan (RPCP)

NASA Technical Reports Server (NTRS)

Cooke, Robert W.

2010-01-01

SCOPE: Prescribes the minimum requirements for the control of cuprous / cupric oxide corrosion (a.k.a. Red Plague) of silver-coated copper wire, cable, and harness assemblies. PURPOSE: Targeted for applications where exposure to assembly processes, environmental conditions, and contamination may promote the development of cuprous / cupric oxide corrosion (a.k.a. Red Plague) in silver-coated copper wire, cable, and harness assemblies. Does not exclude any alternate or contractor-proprietary documents or processes that meet or exceed the baseline of requirements established by this document. Use of alternate or contractor-proprietary documents or processes shall require review and prior approval of the procuring NASA activity.

Development and Field Test of Task-Based MOS-Specific Criterion Measures. Volume 1. Appendixes A-E

DTIC Science & Technology

1988-04-01

WOUND 081-831-1033 APPLY A DRESSING TO AN OPEN HEAD WOUND 081-831-1005 PREVENT SHOCK 081-831-1034 SPLINT A SUSPECTED FRACTURE 081-831-1007 GTVE FIRST...Check seat belts and shoulder harnesses Check unit vehicle/trailer blackout system Service refrigeration unit Check and clean cab interior/exterior...DRESSING TO AN OPEN HEAD WOUND 081-831-1040 TRANSPORT A CASUALTY USING A ONE MAN CARRY 081-831-1041 TRANSPORT A CASUALTY USING A TWO MAN CARRY OR

The Cheshire Jet: Harnessing Metamaterials to Achieve an Optical Stealth Capability

DTIC Science & Technology

2010-07-01

Prometheus Books, 2005. Hamilton, Dave. Address. 23rd Annual National Test and Evaluation Conference, Hilton Head Island, SC, 15 March 2007. http...ment 2008: Challenges and Implications for the Future Joint Force. Norfolk, VA: Center for Joint Futures, 25 November 2008. Valentine, Jason , Shuang

Harnessing collaborative technology to accelerate achievement of chronic disease management objectives for Canada.

PubMed

Thompson, Leslee J; Healey, Lindsay; Falk, Will

2007-01-01

Morgan and colleagues put forth a call to action for the transformation of the Canadian healthcare system through the adoption of a national chronic disease prevention and management (CDPM) strategy. They offer examples of best practices and national solutions including investment in clinical information technologies to help support improved care and outcomes. Although we acknowledge that the authors propose CDPM solutions that are headed in the right direction, more rapid deployment of solutions that harness the potential of advanced collaborative technologies is required. We provide examples of how technologies that exist today can help to accelerate the achievement of some key CDPM objectives.

Compact and mobile high resolution PET brain imager

DOEpatents

Majewski, Stanislaw [Yorktown, VA; Proffitt, James [Newport News, VA

2011-02-08

A brain imager includes a compact ring-like static PET imager mounted in a helmet-like structure. When attached to a patient's head, the helmet-like brain imager maintains the relative head-to-imager geometry fixed through the whole imaging procedure. The brain imaging helmet contains radiation sensors and minimal front-end electronics. A flexible mechanical suspension/harness system supports the weight of the helmet thereby allowing for patient to have limited movements of the head during imaging scans. The compact ring-like PET imager enables very high resolution imaging of neurological brain functions, cancer, and effects of trauma using a rather simple mobile scanner with limited space needs for use and storage.

Would a Higher Minimum Wage Help Poor Families Headed by Women?

ERIC Educational Resources Information Center

Martin, Linda R.; Giannaros, Demetrios

1990-01-01

Studies suggest negative employment consequences if the minimum wage is increased. This may not affect poverty among households headed by women because the unemployment rate does not seem to play a statistically significant role in determining the poverty rate for this cohort. (Author)

The Management of Teachers' Non-Directed Time in a Secondary School

ERIC Educational Resources Information Center

Holmes, Beth

2017-01-01

This article describes a study which investigated the motivations behind why teachers dedicate non-directed time to school-related tasks and the extent to which managers understand and harness these motivations. Data were collected through three case studies within one secondary school. Three heads of department (HoDs) and three teachers were…

14 CFR 29.785 - Seats, berths, litters, safety belts, and harnesses.

Code of Federal Regulations, 2010 CFR

2010-01-01

... dynamic conditions specified in § 29.562. (b) Each occupant must be protected from serious head injury by... combination with the safety belt, constitutes a torso restraint system as described in TSO-C114. (c) Each... weight of at least 170 pounds, considering the dimensional characteristics of the restraint system...

Mapping the Sea Floor of the Historic Area Remediation Site (HARS) Offshore of New York City

USGS Publications Warehouse

Butman, Bradford

2002-01-01

The area offshore of New York City has been used for the disposal of dredged material for over a century. The area has also been used for the disposal of other materials such as acid waste, industrial waste, municipal sewage sludge, cellar dirt, and wood. Between 1976 and 1995, the New York Bight Dredged Material Disposal Site, also known as the Mud Dump Site (MDS), received on average about 6 million cubic yards of dredged material annually. In September 1997 the MDS was closed as a disposal site, and it and the surrounding area were designated as the Historic Area Remediation Site (HARS). The sea floor of the HARS, approximately 9 square nautical miles in area, currently is being remediated by placing a minimum 1-m-thick cap of clean dredged material on top of the surficial sediments that are contaminated from previous disposal of dredged and other materials. The U.S. Geological Survey (USGS) is working cooperatively with the U.S. Army Corps of Engineers (USACE) to map the sea floor geology of the HARS and changes in the characteristics of the surficial sediments over time.

A study to evaluate STS heads-up ascent trajectory performance employing a minimum-Hamiltonian optimization strategy

NASA Technical Reports Server (NTRS)

Sinha, Sujit

1988-01-01

A study was conducted to evaluate the performance implications of a heads-up ascent flight design for the Space Transportation System, as compared to the current heads-down flight mode. The procedure involved the use of the Minimum Hamiltonian Ascent Shuttle Trajectory Evaluation Program, which is a three-degree-of-freedom moment balance simulation of shuttle ascent. A minimum-Hamiltonian optimization strategy was employed to maximize injection weight as a function of maximum dynamic pressure constraint and Solid Rocket Motor burnrate. Performance Reference Mission Four trajectory groundrules were used for consistency. The major conclusions are that for heads-up ascent and a mission nominal design maximum dynamic pressure value of 680 psf, the optimum solid motor burnrate is 0.394 ips, which produces a performance enhancement of 4293 lbm relative to the baseline heads-down ascent, with 0.368 ips burnrate solid motors and a 680 psf dynamic pressure constraint. However, no performance advantage exists for heads-up flight if the current Solid Rocket Motor target burnrate of 0.368 ips is used. The advantage of heads-up ascent flight employing the current burnrate is that Space Shuttle Main Engine throttling for dynamic pressure control is not necessary.

42 CFR 84.151 - Harness test; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

... withstand a pull of 113 kg. (250 pounds) for 30 minutes without failure. (2) Belts, rings, and attachments... minutes without separating, and the hose attachments shall be arranged so that the pull or drag of the... attachment of the line shall permit dragging the maximum length of hose considered for approval over a...

Heterogeneous autoregressive model with structural break using nearest neighbor truncation volatility estimators for DAX.

PubMed

Chin, Wen Cheong; Lee, Min Cherng; Yap, Grace Lee Ching

2016-01-01

High frequency financial data modelling has become one of the important research areas in the field of financial econometrics. However, the possible structural break in volatile financial time series often trigger inconsistency issue in volatility estimation. In this study, we propose a structural break heavy-tailed heterogeneous autoregressive (HAR) volatility econometric model with the enhancement of jump-robust estimators. The breakpoints in the volatility are captured by dummy variables after the detection by Bai-Perron sequential multi breakpoints procedure. In order to further deal with possible abrupt jump in the volatility, the jump-robust volatility estimators are composed by using the nearest neighbor truncation approach, namely the minimum and median realized volatility. Under the structural break improvements in both the models and volatility estimators, the empirical findings show that the modified HAR model provides the best performing in-sample and out-of-sample forecast evaluations as compared with the standard HAR models. Accurate volatility forecasts have direct influential to the application of risk management and investment portfolio analysis.

Compact Telerobot Hand

NASA Technical Reports Server (NTRS)

Rosheim, Mark; Trechsel, Hans

1993-01-01

Anthropomorphic telerobotic hand contains actuators, joints, sensors, and complex wiring harnesses. Glove protects interior components of hand from dirt and damage. Imitates motions of human fingers and wrist in lifelike and dexterous way. Incorporates pitch/yaw joints in wrist and head knuckles. Hand modular; so fingers removable, interchangeable units. Feature simplifies servicing and maintenance, which must be done frequently in such complex mechanism.

Mike's Guiding Warmth

ERIC Educational Resources Information Center

Leckie, Linda

2010-01-01

Mike Elrick knew how to stay warm. He loved to wrap himself from head to toe in wool; the author pictures Mike as a wool-clad moccasin-footed snow walker twisting into lampwick harnesses with his trail axe looped through his belt. Mike looked forward to winter and welcomed a drop in the mercury--the lower the better! He loved the physical work of…

ExoMars Raman laser spectrometer overview

NASA Astrophysics Data System (ADS)

Rull, F.; Sansano, A.; Díaz, E.; Canora, C. P.; Moral, A. G.; Tato, C.; Colombo, M.; Belenguer, T.; Fernández, M.; Manfredi, J. A. R.; Canchal, R.; Dávila, B.; Jiménez, A.; Gallego, P.; Ibarmia, S.; Prieto, J. A. R.; Santiago, A.; Pla, J.; Ramos, G.; González, C.

2010-09-01

The Raman Laser Spectrometer (RLS) is one of the Pasteur Payload instruments, within the ESA's Aurora Exploration Programme, ExoMars mission. The RLS Instrument will perform Raman spectroscopy on crushed powered samples deposited on a small container after crushing the cores obtained by the Rover's drill system. This is the first time that a Raman spectrometer will be launched in an out planetary mission. The Instrument will be accommodated and operate inside the Rover's ALD (Analytical Laboratory Drawer), complying with COSPAR (Committee on Space Research) Planetary Protection requirements. The RLS Instrument is composed by the following units: SPU (Spectrometer Unit); iOH: (Internal Optical Head); ICEU (Instrument Control and Excitation Unit). Other instrument units are EH (Electrical Harness), OH (Optical Harness) and RLS SW On-Board.

49 CFR 179.400-8 - Thickness of plates.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-8 Thickness of plates... joints, except that for seamless heads, E = 1.0. (b) The minimum wall thickness, after forming, of any 3..., except that for seamless heads, E=1.0. (c) The minimum wall thickness, after forming, of a flanged and...

49 CFR 179.400-8 - Thickness of plates.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-8 Thickness of plates... joints, except that for seamless heads, E = 1.0. (b) The minimum wall thickness, after forming, of any 3..., except that for seamless heads, E=1.0. (c) The minimum wall thickness, after forming, of a flanged and...

49 CFR 179.400-8 - Thickness of plates.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Specification for Cryogenic Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400... welded joints, except that for seamless heads, E = 1.0. (b) The minimum wall thickness, after forming, of..., except that for seamless heads, E=1.0. (c) The minimum wall thickness, after forming, of a flanged and...

49 CFR 179.400-8 - Thickness of plates.

Code of Federal Regulations, 2014 CFR

2014-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-8 Thickness of plates... joints, except that for seamless heads, E = 1.0. (b) The minimum wall thickness, after forming, of any 3..., except that for seamless heads, E=1.0. (c) The minimum wall thickness, after forming, of a flanged and...

49 CFR 179.400-8 - Thickness of plates.

Code of Federal Regulations, 2013 CFR

2013-10-01

... Liquid Tank Car Tanks and Seamless Steel Tanks (Classes DOT-113 and 107A) § 179.400-8 Thickness of plates... joints, except that for seamless heads, E = 1.0. (b) The minimum wall thickness, after forming, of any 3..., except that for seamless heads, E=1.0. (c) The minimum wall thickness, after forming, of a flanged and...

Navigator alignment using radar scan

DOEpatents

Doerry, Armin W.; Marquette, Brandeis

2016-04-05

The various technologies presented herein relate to the determination of and correction of heading error of platform. Knowledge of at least one of a maximum Doppler frequency or a minimum Doppler bandwidth pertaining to a plurality of radar echoes can be utilized to facilitate correction of the heading error. Heading error can occur as a result of component drift. In an ideal situation, a boresight direction of an antenna or the front of an aircraft will have associated therewith at least one of a maximum Doppler frequency or a minimum Doppler bandwidth. As the boresight direction of the antenna strays from a direction of travel at least one of the maximum Doppler frequency or a minimum Doppler bandwidth will shift away, either left or right, from the ideal situation.

Variability of medial and posterior offset in patients with fourth-generation stemmed shoulder arthroplasty.

PubMed

Irlenbusch, Ulrich; Berth, Alexander; Blatter, Georges; Zenz, Peter

2012-03-01

Most anthropometric data on the proximal humerus has been obtained from deceased healthy individuals with no deformities. Endoprostheses are implanted for primary and secondary osteoarthritis, rheumatoid arthritis,humeral-head necrosis, fracture sequelae and other humeral-head deformities. This indicates that pathologicoanatomical variability may be greater than previously assumed. We therefore investigated a group of patients with typical shoulder replacement diagnoses, including posttraumatic and rheumatic deformities. One hundred and twenty-two patients with a double eccentrically adjustable shaft endoprosthesis served as a specific dimension gauge to determine in vivo the individual humeral-head rotation centres from the position of the adjustable prosthesis taper and the eccentric head. All prosthesis heads were positioned eccentrically.The entire adjustment range of the prosthesis of 12 mm medial/lateral and 6 mm dorsal/ventral was required. Mean values for effective offset were 5.84 mm mediolaterally[standard deviation (SD) 1.95, minimum +2, maximum +11]and 1.71 mm anteroposteriorly (SD 1.71, minimum −3,maximum 3 mm), averaging 5.16 mm (SD 1.76, minimum +2,maximum + 10). The posterior offset averaged 1.85 mm(SD 1.85, minimum −1, maximum + 6 mm). In summary, variability of the combined medial and dorsal offset of the humeral-head rotational centre determined in patients with typical underlying diagnoses in shoulder replacement was not greater than that recorded in the literature for healthy deceased patients.The range of deviation is substantial and shows the need for an adjustable prosthetic system.

Immunotherapy for Head and Neck Squamous Cell Carcinoma: A Review of Current and Emerging Therapeutic Options

PubMed Central

Moskovitz, Jessica M.; Moy, Jennifer; Seiwert, Tanguy Y.

2017-01-01

Abstract Advances in the field of cancer immunotherapy have occurred rapidly over the past decade. Exciting results from clinical trials have led to new treatment options and improved survival for patients with a myriad of solid tumor pathologies. However, questions remain unanswered regarding duration and timing of therapy, combination regimens, appropriate biomarkers of disease, and optimal monitoring of therapeutic response. This article reviews emerging immunotherapeutic agents and significant clinical trials that have led to advancements in the field of immuno‐oncology for patients with head and neck squamous cell carcinoma. Implications for Practice. This review article summarizes recently developed agents that harness the immune system to fight head and neck squamous cell carcinoma. A brief review of the immune system and its role in cancer development is included. Recently completed and emerging therapeutic trials centering on the immune system and head and neck cancer are reviewed. PMID:28507203

14 CFR 25.149 - Minimum control speed.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 1 2011-01-01 2011-01-01 false Minimum control speed. 25.149 Section 25... Minimum control speed. (a) In establishing the minimum control speeds required by this section, the method... prevent a heading change of more than 20 degrees. (e) VMCG, the minimum control speed on the ground, is...

14 CFR 25.149 - Minimum control speed.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Minimum control speed. 25.149 Section 25... Minimum control speed. (a) In establishing the minimum control speeds required by this section, the method... prevent a heading change of more than 20 degrees. (e) VMCG, the minimum control speed on the ground, is...

77 FR 13626 - Notice of Inventory Completion: Maxey Museum, Whitman College, Walla Walla, WA

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-07

... remains representing, at minimum, six individuals were removed from an unknown location near the..., consisting of: 3 envelopes with writing; 1 lot of small pieces of leather belt or harness; 1 lot of charcoal pieces; 3 metal bells; 1 pipe stem; 1 piece of iron; 1 envelope with no writing; 1 chert flake; 1 lot of...

Multiple regression analysis of anthropometric measurements influencing the cephalic index of male Japanese university students.

PubMed

Hossain, Md Golam; Saw, Aik; Alam, Rashidul; Ohtsuki, Fumio; Kamarul, Tunku

2013-09-01

Cephalic index (CI), the ratio of head breadth to head length, is widely used to categorise human populations. The aim of this study was to access the impact of anthropometric measurements on the CI of male Japanese university students. This study included 1,215 male university students from Tokyo and Kyoto, selected using convenient sampling. Multiple regression analysis was used to determine the effect of anthropometric measurements on CI. The variance inflation factor (VIF) showed no evidence of a multicollinearity problem among independent variables. The coefficients of the regression line demonstrated a significant positive relationship between CI and minimum frontal breadth (p < 0.01), bizygomatic breadth (p < 0.01) and head height (p < 0.05), and a negative relationship between CI and morphological facial height (p < 0.01) and head circumference (p < 0.01). Moreover, the coefficient and odds ratio of logistic regression analysis showed a greater likelihood for minimum frontal breadth (p < 0.01) and bizygomatic breadth (p < 0.01) to predict round-headedness, and morphological facial height (p < 0.05) and head circumference (p < 0.01) to predict long-headedness. Stepwise regression analysis revealed bizygomatic breadth, head circumference, minimum frontal breadth, head height and morphological facial height to be the best predictor craniofacial measurements with respect to CI. The results suggest that most of the variables considered in this study appear to influence the CI of adult male Japanese students.

49 CFR 173.314 - Compressed gases in tank cars and multi-unit tank cars.

Code of Federal Regulations, 2013 CFR

2013-10-01

... applicable authorized tank car specification and must be equipped with a head shield as prescribed in § 179... jacket and head shield. When the jacket and head shield are made from any authorized steel with a minimum... jacket and head shield must be increased by a factor of 1.157. Forming allowances for heads are not...

49 CFR 173.314 - Compressed gases in tank cars and multi-unit tank cars.

Code of Federal Regulations, 2014 CFR

2014-10-01

... applicable authorized tank car specification and must be equipped with a head shield as prescribed in § 179... jacket and head shield. When the jacket and head shield are made from any authorized steel with a minimum... jacket and head shield must be increased by a factor of 1.157. Forming allowances for heads are not...

Failed Pavlik harness treatment for DDH as a risk factor for avascular necrosis.

PubMed

Tiruveedhula, Madhu; Reading, Isabel C; Clarke, Nicholas M P

2015-03-01

Avascular necrosis (AVN) of the femoral head is an irreversible complication seen in the treatment of developmental dysplasia of hip (DDH) with the Pavlik harness. Its incidence is reported to be low after successful reduction of the hip but high if the hip is not concentrically relocated. We aim to investigate its incidence after failed Pavlik harness treatment. We prospectively followed up a group of children who failed Pavlik harness treatment for DDH treated at our institution by the senior author between 1988 and 2001 and compared their rates of AVN with a group of children who presented late and hence were treated surgically. AVN was graded as described by Kalamchi and MacEwen and only grade 2 to 4 AVN was considered significant and included in the analysis. Thirty-seven hips were included in the failed Pavlik group (group 1) and 86 hips in the no Pavlik group (group 2). Ten hips in group 1 developed AVN (27%), whereas only 7 hips in group 2 (8%) developed AVN; the odds of developing AVN after failed Pavlik treatment was 4.7 (95% confidence interval, 1.3-14.1) (P=0.009) with a relative risk of 3.32 (range, 1.37 to 8.05). There was no statistically significant association observed with duration of splintage and severity of AVN (Spearman's correlation, -0.46; P=0.18). However, there was a positive correlation noted with age at presentation and severity of AVN. Therefore, we advise close monitoring of hips in the Pavlik harness and discontinue its use if the hips are not reduced within 3 weeks. Level III.

Stability analysis of a run-of-river diversion hydropower plant with surge tank and spillway in the head pond.

PubMed

Sarasúa, José Ignacio; Elías, Paz; Martínez-Lucas, Guillermo; Pérez-Díaz, Juan Ignacio; Wilhelmi, José Román; Sánchez, José Ángel

2014-01-01

Run-of-river hydropower plants usually lack significant storage capacity; therefore, the more adequate control strategy would consist of keeping a constant water level at the intake pond in order to harness the maximum amount of energy from the river flow or to reduce the surface flooded in the head pond. In this paper, a standard PI control system of a run-of-river diversion hydropower plant with surge tank and a spillway in the head pond that evacuates part of the river flow plant is studied. A stability analysis based on the Routh-Hurwitz criterion is carried out and a practical criterion for tuning the gains of the PI controller is proposed. Conclusions about the head pond and surge tank areas are drawn from the stability analysis. Finally, this criterion is applied to a real hydropower plant in design state; the importance of considering the spillway dimensions and turbine characteristic curves for adequate tuning of the controller gains is highlighted.

Stability Analysis of a Run-of-River Diversion Hydropower Plant with Surge Tank and Spillway in the Head Pond

PubMed Central

Sarasúa, José Ignacio; Elías, Paz; Wilhelmi, José Román; Sánchez, José Ángel

2014-01-01

Run-of-river hydropower plants usually lack significant storage capacity; therefore, the more adequate control strategy would consist of keeping a constant water level at the intake pond in order to harness the maximum amount of energy from the river flow or to reduce the surface flooded in the head pond. In this paper, a standard PI control system of a run-of-river diversion hydropower plant with surge tank and a spillway in the head pond that evacuates part of the river flow plant is studied. A stability analysis based on the Routh-Hurwitz criterion is carried out and a practical criterion for tuning the gains of the PI controller is proposed. Conclusions about the head pond and surge tank areas are drawn from the stability analysis. Finally, this criterion is applied to a real hydropower plant in design state; the importance of considering the spillway dimensions and turbine characteristic curves for adequate tuning of the controller gains is highlighted. PMID:25405237

The Impact of Harness Impedance on Hall Thruster Discharge Oscillations

NASA Technical Reports Server (NTRS)

Pinero, Luis R.

2017-01-01

Hall thrusters exhibit characteristic discharge voltage and current oscillations during steady-state operation. The lower frequency breathing-mode current oscillations are inherent to each thruster and could impact thruster operation and power processing unit (PPU) design. The design of the discharge output filter, in particular, the output capacitor is important because it supplies the high peak current oscillations that the thruster demands. However, space-rated, high-voltage capacitors are not readily available and can have significant mass and volume. So, it is important for a PPU designer to know what is the minimum amount of capacitance required to operate a thruster. Through Simulation Program with Integrated Circuit Emphasis modeling and electrical measurements on the Hall Effect Rocket with Magnetic Shielding thruster, it was shown that the harness impedance between the power supply and the thruster is the main contributor towards generating voltage ripple at the thruster. Also, increasing the size of the discharge filter capacitor, as previously implemented during thruster tests, does not reduce the voltage oscillations. The electrical characteristics of the electrical harness between the discharge supply and the thruster is crucial to system performance and could have a negative impact on performance, life and operation.

The Impact of Harness Impedance on Hall Thruster Discharge Oscillations

NASA Technical Reports Server (NTRS)

Pinero, Luis R.

2017-01-01

Hall thrusters exhibit characteristic discharge voltage and current oscillations during steady-state operation. The lower frequency breathing-mode current oscillations are inherent to each thruster and could impact thruster operation and PPU design. The design of the discharge output filter, in particular, the output capacitor is important because it supplies the high peak current oscillations that the thruster demands. However, space-rated, high-voltage capacitors are not readily available and can have significant mass and volume. So, it is important for a PPU designer to know what is the minimum amount of capacitance required to operate a thruster. Through SPICE modeling and electrical measurements on the Hall Effect Rocket with Magnetic Shielding (HERMeS) thruster, it was shown that the harness impedance between the power supply and the thruster is the main contributor towards generating voltage ripple at the thruster. Also, increasing the size of the discharge filter capacitor, as previously implemented during thruster tests, does not reduce the voltage oscillations. The electrical characteristics of the electrical harness between the discharge supply and the thruster is crucial to system performance and could have a negative impact on performance, life and operation.

Conservation of water for washing beef heads at harvest

USDA-ARS?s Scientific Manuscript database

The objective of this research was to develop methods to conserve water necessary to cleanse beef heads prior to USDA–FSIS inspection. This was to be accomplished by establishing a baseline for the minimum amount of water necessary to adequately wash a head and application of image analysis to provi...

78 FR 17778 - Privacy Act of 1974; System of Records

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-22

... System,'' paragraph (iii), first sentence, we inadvertently left out ``minimum data set''. We are adding ``minimum data set'' right after the word ``registry''. And under the heading, ``Routine Uses of Records... sentence, insert ``minimum data set,'' immediately after the word ``registry,''. On the same page, renumber...

Effectiveness of Interaural Delays Alone as Cues During Dynamic Sound Localization

NASA Technical Reports Server (NTRS)

Wenzel, Elizabeth M.; Null, Cynthia H. (Technical Monitor)

1996-01-01

The contribution of interaural time differences (ITDs) to the localization of virtual sound sources with and without head motion was examined. Listeners estimated the apparent azimuth, elevation and distance of virtual sources presented over headphones. Stimuli (3 sec., white noise) were synthesized from minimum-phase representations of nonindividualized head-related transfer functions (HRTFs); binaural magnitude spectra were derived from the minimum phase estimates and ITDs were represented as a pure delay. During dynamic conditions, listeners were encouraged to move their heads; head position was tracked and stimuli were synthesized in real time using a Convolvotron to simulate a stationary external sound source. Two synthesis conditions were tested: (1) both interaural level differences (ILDs) and ITDs correctly correlated with source location and head motion, (2) ITDs correct, no ILDs (flat magnitude spectrum). Head movements reduced azimuth confusions primarily when interaural cues were correctly correlated, although a smaller effect was also seen for ITDs alone. Externalization was generally poor for ITD-only conditions and was enhanced by head motion only for normal HRTFs. Overall the data suggest that, while ITDs alone can provide a significant cue for azimuth, the errors most commonly associated with virtual sources are reduced by location-dependent magnitude cues.

Morphometric distances among five ethnic groups and evaluation of the secular trend in historical Libya.

PubMed

Danubio, Maria Enrica; Martorella, Domenico; Rufo, Fabrizio; Vecchi, Elvira; Sanna, Emanuele

2011-01-01

This study analysed the variations, both in space and time, of 10 body dimensions and 2 anthropometric indexes of 745 adult males belonging to 5 ethnic groups of historical Lybia (el-Haràbi, el-Baraghìts, Marabtìn, Oases inhabitants and Tuareg). The data were collected in the years 1928 and 1932 by Puccioni and Cipriani, two Italian anthropologists. The aim was to reconstruct the biological history of Libya at the time, and thus contribute to the ongoing debate on the evolution of the biological standard of living in developing Countries. The subjects were analysed by ethnicity and by 10-year age groups, after adjusting for age. The results of ANCOVA and Tukey's post-hoc test show that among and between groups there are statistical significant differences overall for armspan, height, head breadth, bizygomatic breadth, biiliac breadth/height and head breadth/head length indexes. By means of the cluster analysis, the el-Haràbi, el-Baraghìts and Marabtìn groups cluster together, whereas the Tuareg and Oases inhabitants cluster separately one from the other and both from the other three ethnic groups. Within-group variations are not very marked in all ethnicities. In general, there is the tendency, not statistically significant, to the reduction and/or stasis of body dimensions from the older to the younger, and the differences are greater among the older than the younger age classes. In conclusion, it can be argued that these groups, all different culturally and geographically, were following the same tendency of stasis of the secular trend of the body dimensions considered in this study, and such stasis persisted since, at least, the last twenty years of the 19th century, when the older were born.

Predictive Compensator Optimization for Head Tracking Lag in Virtual Environments

NASA Technical Reports Server (NTRS)

Adelstein, Barnard D.; Jung, Jae Y.; Ellis, Stephen R.

2001-01-01

We examined the perceptual impact of plant noise parameterization for Kalman Filter predictive compensation of time delays intrinsic to head tracked virtual environments (VEs). Subjects were tested in their ability to discriminate between the VE system's minimum latency and conditions in which artificially added latency was then predictively compensated back to the system minimum. Two head tracking predictors were parameterized off-line according to cost functions that minimized prediction errors in (1) rotation, and (2) rotation projected into translational displacement with emphasis on higher frequency human operator noise. These predictors were compared with a parameterization obtained from the VE literature for cost function (1). Results from 12 subjects showed that both parameterization type and amount of compensated latency affected discrimination. Analysis of the head motion used in the parameterizations and the subsequent discriminability results suggest that higher frequency predictor artifacts are contributory cues for discriminating the presence of predictive compensation.

A Report on the Development of Rare Earth-Cobalt Permanent Magnet Technology - Japan.

DTIC Science & Technology

1981-07-01

Implantable pumps and valves , head support harness in development). C. MICROWAVE AND ION BEAM TECHNOLOGY 1. Microwave Tubes: TWT PPM focusing, klystrons...III and IV were devoted to various medical applications that employ REPM. These included various dental prosthetic devices, tech- niques for measuring...minimize losses due to fracture in handling or heat treatment. Very little work has been done on this topic in the West or in Japan. The only two papers

[Social marketers' lack of success in using CSM discipline to harness commercial resources and increase contraceptive prevalence].

PubMed

Davies, J

1984-01-01

Social marketers have certainly shown that the CSM discipline can quickly and cost-effectively harness commercial resources to increase contraceptive prevalence. But why hasn't the social marketing idea caught on in more countries? According to Social Marketing Forum, only a tiny number of countries have active programs after more than a decade of effort. The most likely reason for this lack of success is doubt and fear on the part of both developing countries' officials and donor agencies about allowing marketing enthusiasts--with our very noticeable advertising methods--to join the family planning fight. And what has our answer been? Usually, a head-on retort such as, "But look at all the condoms we've sold]" And that gets us nowhere, because the successful peddling of 1 not-so-impressive method doesn't begin to balance the fears of a possible backlash that brash condom promotions could bring down on official heads. The lesson we should be learning is that social marketers possess to narrow an outlook and promote a small range of products that don't enthuse decisionmakers. Hence, we are often perceived as condom salesmen--and not much more. What should we be doing? We should be selling the idea of using private sector experience to assist national development. That means social development, particularly improved health, family planning and women's education. These 3 activities have proven effective in reducing fertility and would add up to a marketing opportunity--a longterm challenge that should enthuse dicisionmakers, private sector entrepreneurs and donor agencies alike. Further, our model--the commercial sector--is renowned for branching out and secceeding in a broad range of endeavors. As an example, Procter and Gamble uses separate divisions to market different products. Initiatives already exist in many countries to harness the private sector as a development tool. Social marketers should be leading the initiative--and benefitting from it, too. full text

Developmental dysplasia of the hip in the newborn: A systematic review

PubMed Central

Gulati, Vivek; Eseonu, Kelechi; Sayani, Junaid; Ismail, Nizar; Uzoigwe, Chika; Choudhury, Muhammed Zaki; Gulati, Pooja; Aqil, Adeel; Tibrewal, Saket

2013-01-01

Developmental dysplasia of the hip (DDH) denotes a wide spectrum of conditions ranging from subtle acetabular dysplasia to irreducible hip dislocations. Clinical diagnostic tests complement ultrasound imaging in allowing diagnosis, classification and monitoring of this condition. Classification systems relate to the alpha and beta angles in addition to the dynamic coverage index (DCI). Screening programmes for DDH show considerable geographic variation; certain risk factors have been identified which necessitate ultrasound assessment of the newborn. The treatment of DDH has undergone significant evolution, but the current gold standard is still the Pavlik harness. Duration of Pavlik harness treatment has been reported to range from 3 to 9.3 mo. The beta angle, DCI and the superior/lateral femoral head displacement can be assessed via ultrasound to estimate the likelihood of success. Success rates of between 7% and 99% have been reported when using the harness to treat DDH. Avascular necrosis remains the most devastating complication of harness usage with a reported rate of between 0% and 28%. Alternative non-surgical treatment methods used for DDH include devices proposed by LeDamany, Frejka, Lorenz and Ortolani. The Rosen splint and Wagner stocking have also been used for DDH treatment. Surgical treatment for DDH comprises open reduction alongside a combination of femoral or pelvic osteotomies. Femoral osteotomies are carried out in cases of excessive anteversion or valgus deformity of the femoral neck. The two principal pelvic osteotomies most commonly performed are the Salter osteotomy and Pemberton acetabuloplasty. Serious surgical complications include epiphyseal damage, sciatic nerve damage and femoral neck fracture. PMID:23610749

[Glaucoma and optic nerve drusen: Limitations of optic nerve head OCT].

PubMed

Poli, M; Colange, J; Goutagny, B; Sellem, E

2017-09-01

Optic nerve head drusen are congenital calcium deposits located in the prelaminar section of the optic nerve head. Their association with visual field defects has been classically described, but the diagnosis of glaucoma is not easy in these cases of altered optic nerve head anatomy. We describe the case of a 67-year-old man with optic nerve head drusen complicated by glaucoma, which was confirmed by visual field and OCT examination of the peripapillary retinal nerve fiber layer (RNFL), but the measurement of the minimum distance between the Bruch membrane opening and the internal limiting membrane (minimum rim width, BMO-MRW) by OCT was normal. OCT of the BMO-MRW is a new diagnostic tool for glaucoma. Superficial optic nerve head drusen, which are found between the internal limiting membrane and the Bruch's membrane opening, overestimate the value of this parameter. BMO-MRW measurement is not adapted to cases of optic nerve head drusen and can cause false-negative results for this parameter, and the diagnosis of glaucoma in this case should be based on other parameters such as the presence of a fascicular defect in the retinal nerve fibers, RNFL or macular ganglion cell complex thinning, as well as visual field data. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Handbook of Pressure-Proof Connector and Cable Harness Design for Sonar Systems.

DTIC Science & Technology

1981-12-21

as delrin, polycarbonate, epoxy, melamine , and diallyl phthalate were evaluated. Glass -filled diallyl phthalate was the only candidate material which...and at 900 intervals on the bulk- head of glass sealed receptacles, 0.125 inch from the outermost glass bead . 7-3 :1 7.2.1.5 The area of the component...in their ability to cure resins , as well as their tendency to cause skin irritation or dermatitis. Most room temperature-set hardeners are based on

Initial Assessment of Human Performance Using the Gaiter Interaction Technique to Control Locomotion in Fully Immersive Virtual Environments

DTIC Science & Technology

2004-06-30

virtual space, as well as to match specific attributes of natural locomotion, such as perceived velocity and caloric expenditure . Moreover, the...wide range of postural motions (e.g., crouching, jumping , and bending to look around objects) with gestural stepping motions. The attributes of in...approximately 8 ¥ 8 ¥ 8 ft. The harness itself was an initial design made out of PVC pipe at the waist and above the head, with rope connecting the

Head impact mechanisms of a child occupant seated in a child restraint system as determined by impact testing.

PubMed

Yoshida, Ryoichi; Okada, Hiroshi; Nomura, Mitsunori; Mizuno, Koji; Tanaka, Yoshinori; Hosokawa, Naruyuki

2011-11-01

In side collision accidents, the head is the most frequently injured body region for child occupants seated in a child restraint system (CRS). Accident analyses show that a child's head can move out of the CRS shell, make hard contact with the vehicle interior, and thus sustain serious injuries. In order to improve child head protection in side collisions, it is necessary to understand the injury mechanism of a child in the CRS whose head makes contact with the vehicle interior. In this research, an SUV-to-car oblique side crash test was conducted to reconstruct such head contacts. A Q3s child dummy was seated in a CRS in the rear seat of the target car. The Q3s child dummy's head moved out beyond the CRS side wing, moved laterally, and made contact with the side window glass and the doorsill. It was demonstrated that the hard head contact, which produced a high HIC value, could occur in side collisions. A series of sled tests was carried out to reproduce the dummy kinematic behavior observed in the SUV-to-car crash test, and the sled test conditions such as sled angle, ECE seat slant angle and velocity-time history that duplicated the kinematic behavior were determined. A parametric study also was conducted with the sled tests; and it was found that the impact angle, harness slack, chest clip, and the CRS side wing shape affected the torso motion and head contact with the vehicle interior.

Setting Standards for Minimum Competency Tests.

ERIC Educational Resources Information Center

Mehrens, William A.

Some general questions about minimum competency tests are discussed, and various methods of setting standards are reviewed with major attention devoted to those methods used for dichotomizing a continuum. Methods reviewed under the heading of Absolute Judgments of Test Content include Nedelsky's, Angoff's, Ebel's, and Jaeger's. These methods are…

Ridge sowing of sunflower (Helianthus annuus L.) in a minimum till system improves the productivity, oil quality, and profitability on a sandy loam soil under an arid climate.

PubMed

Sher, Ahmad; Suleman, Muhammad; Qayyum, Abdul; Sattar, Abdul; Wasaya, Allah; Ijaz, Muhammad; Nawaz, Ahmad

2018-04-01

Sunflower (Helianthus annuus L.) is a major oilseed crop grown for its edible oil across the globe including Pakistan. In Pakistan, the production of edible oil is less than the required quantity; the situation is being worsened with the increasing population. Thus, there is dire need to grow those sunflower genotypes which perform better under a given set of agronomic practices. In this 2-year study, we compared four sunflower genotypes, viz., Armoni, Kundi, Sinji, and S-278 for their yield potential, oil contents, fatty acid composition, and profitability under three sowing methods, viz., bed sowing, line sowing, and ridge sowing and two tillage system, viz., plow till and minimum till. Among the sunflower genotypes, the genotype Armoni produced the highest plant height, number of leaves, head diameter, 1000-achene weight, and achene yield; the oil contents and oleic acid were the highest in genotype Sinji. Among the sowing methods, the highest number of leaves per plant, head diameter, number of achenes per head, achene yield, and oil contents were recorded in ridge sowing. Among the tillage systems, the highest head diameter 16. 2 cm, 1000-achene weight (57.2 g), achene yield (1.8 t ha -1 ), oil contents (35.2%), and oleic acid (15.2%) were recorded in minimum till sunflower. The highest net benefits and benefit to cost ratio were recorded in minimum till ridge sown Armoni genotype. In conclusion, the genotype Armoni should be grown on ridges to achieve the highest achene yield, oil contents, and net profitability.

40 CFR 170.240 - Personal protective equipment.

Code of Federal Regulations, 2010 CFR

2010-07-01

... protective equipment (PPE) means devices and apparel that are worn to protect the body from contact with... chemical-resistant garment that covers, at a minimum, the entire body except head, hands, and feet. (4... body except head, hands, and feet. The pesticide product labeling may specify that the coveralls be...

Fatigue Behavior of an Advanced SiC/SiC Composite with an Oxidation Inhibited Matrix at 1200 deg C in Air and in Steam

DTIC Science & Technology

2010-03-01

eight-harness-satin (8HS) weave plies. Tensile stress -strain behavior and tensile properties were evaluated at 1200˚C. Tension-tension fatigue tests...ratio of minimum stress to maximum stress of R = 0.05, with maximum stresses ranging from 100 to 140 MPa in air and in steam. Fatigue run-out was...Hz, the presence of steam appeared to have little influence on the fatigue resistance for the fatigue stress levels < 140 MPa. The presence of steam

The minimum follow-up required for radial head arthroplasty: a meta-analysis.

PubMed

Laumonerie, P; Reina, N; Kerezoudis, P; Declaux, S; Tibbo, M E; Bonnevialle, N; Mansat, P

2017-12-01

The primary aim of this study was to define the standard minimum follow-up required to produce a reliable estimate of the rate of re-operation after radial head arthroplasty (RHA). The secondary objective was to define the leading reasons for re-operation. Four electronic databases, between January 2000 and March 2017 were searched. Articles reporting reasons for re-operation (Group I) and results (Group II) after RHA were included. In Group I, a meta-analysis was performed to obtain the standard minimum follow-up, the mean time to re-operation and the reason for failure. In Group II, the minimum follow-up for each study was compared with the standard minimum follow-up. A total of 40 studies were analysed: three were Group I and included 80 implants and 37 were Group II and included 1192 implants. In Group I, the mean time to re-operation was 1.37 years (0 to 11.25), the standard minimum follow-up was 3.25 years; painful loosening was the main indication for re-operation. In Group II, 33 Group II articles (89.2%) reported a minimum follow-up of < 3.25 years. The literature does not provide a reliable estimate of the rate of re-operation after RHA. The reproducibility of results would be improved by using a minimum follow-up of three years combined with a consensus of the definition of the reasons for failure after RHA. Cite this article: Bone Joint J 2017;99-B:1561-70. ©2017 The British Editorial Society of Bone & Joint Surgery.

Efforts to Prevent Concussions Target Schools

ERIC Educational Resources Information Center

Samuels, Christina A.

2010-01-01

The number of sports-related concussions reported by young athletes is on the rise, prompting awareness campaigns from athletic and medical groups, as well as proposed federal legislation to set minimum standards for concussion management in public schools. Concussions are caused by a jolt to the body or a blow to the head that causes the head to…

Comparison of reproducibility of natural head position using two methods.

PubMed

Khan, Abdul Rahim; Rajesh, R N G; Dinesh, M R; Sanjay, N; Girish, K S; Venkataraghavan, Karthik

2012-01-01

Lateral cephalometric radiographs have become virtually indispensable to orthodontists in the treatment of patients. They are important in orthodontic growth analysis, diagnosis, treatment planning, monitoring of therapy and evaluation of final treatment outcome. The purpose of this study was to evaluate and compare the maximum reproducibility with minimum variation of natural head position using two methods, i.e. the mirror method and the fluid level device method. The study included two sets of 40 lateral cephalograms taken using two methods of obtaining natural head position: (1) The mirror method and (2) fluid level device method, with a time interval of 2 months. Inclusion criteria • Subjects were randomly selected aged between 18 to 26 years Exclusion criteria • History of orthodontic treatment • Any history of respiratory tract problem or chronic mouth breathing • Any congenital deformity • History of traumatically-induced deformity • History of myofacial pain syndrome • Any previous history of head and neck surgery. The result showed that both the methods for obtaining natural head position-the mirror method and fluid level device method were comparable, but maximum reproducibility was more with the fluid level device as shown by the Dahlberg's coefficient and Bland-Altman plot. The minimum variance was seen with the fluid level device method as shown by Precision and Pearson correlation. The mirror method and the fluid level device method used for obtaining natural head position were comparable without any significance, and the fluid level device method was more reproducible and showed less variance when compared to mirror method for obtaining natural head position. Fluid level device method was more reproducible and shows less variance when compared to mirror method for obtaining natural head position.

Triple innominate osteotomy for Legg-Calvé-Perthes disease in children: does the lateral coverage change with time?

PubMed

Hosalkar, Harish; Munhoz da Cunha, Ana Laura; Baldwin, Keith; Ziebarth, Kai; Wenger, Dennis R

2012-09-01

Triple innominate osteotomy (TIO) is one of the modalities of surgical containment in Legg-Calvé-Perthes disease (LCPD). However, overcoverage with TIO can lead to pincer impingement. We therefore asked (1) whether TIO contained the femoral head in Catterall Stages III and IV of LCPD; (2) whether the center-edge (CE) angle, acetabular roof arc angle (ARA), and Sharp's angle changed during the growing years; and (3) what percentage of patients had radiographic evidence of pincer impingement beyond a minimum followup of 3 years. We identified 19 children who had 20 TIOs performed for Catterall Stages III and IV LCPD. Two blinded observers assessed sequential radiographs. Each observer made two sets of readings more than 2 weeks apart. Femoral head extrusion index, CE angle of Wiberg, ARA, and Sharp's angle were measured. Minimum followup was 3 years to document continued acetabular growth (mean, 3.8 years; range, 3-7 years). All patients exhibited femoral head containment at last followup. Eleven of 20 hips demonstrated no radiographic evidence of pincer morphology beyond a minimum followup of 3 years (mean, 3.8 years). Patients with CE angle corrected to 44° or less and an ARA of greater than -6° after TIO did not demonstrate a pincer morphology at last followup. TIO resulted in femoral head containment in all cases. Lateral acetabular coverage changed during the growing years in all patients. Surgical correction beyond 44° of CE angle and -6° of ARA should be avoided to prevent pincer morphology later.

An Adaptive Clustering Approach Based on Minimum Travel Route Planning for Wireless Sensor Networks with a Mobile Sink.

PubMed

Tang, Jiqiang; Yang, Wu; Zhu, Lingyun; Wang, Dong; Feng, Xin

2017-04-26

In recent years, Wireless Sensor Networks with a Mobile Sink (WSN-MS) have been an active research topic due to the widespread use of mobile devices. However, how to get the balance between data delivery latency and energy consumption becomes a key issue of WSN-MS. In this paper, we study the clustering approach by jointly considering the Route planning for mobile sink and Clustering Problem (RCP) for static sensor nodes. We solve the RCP problem by using the minimum travel route clustering approach, which applies the minimum travel route of the mobile sink to guide the clustering process. We formulate the RCP problem as an Integer Non-Linear Programming (INLP) problem to shorten the travel route of the mobile sink under three constraints: the communication hops constraint, the travel route constraint and the loop avoidance constraint. We then propose an Imprecise Induction Algorithm (IIA) based on the property that the solution with a small hop count is more feasible than that with a large hop count. The IIA algorithm includes three processes: initializing travel route planning with a Traveling Salesman Problem (TSP) algorithm, transforming the cluster head to a cluster member and transforming the cluster member to a cluster head. Extensive experimental results show that the IIA algorithm could automatically adjust cluster heads according to the maximum hops parameter and plan a shorter travel route for the mobile sink. Compared with the Shortest Path Tree-based Data-Gathering Algorithm (SPT-DGA), the IIA algorithm has the characteristics of shorter route length, smaller cluster head count and faster convergence rate.

The Relative Contribution of Interaural Time and Magnitude Cues to Dynamic Sound Localization

NASA Technical Reports Server (NTRS)

Wenzel, Elizabeth M.; Null, Cynthia H. (Technical Monitor)

1995-01-01

This paper presents preliminary data from a study examining the relative contribution of interaural time differences (ITDs) and interaural level differences (ILDs) to the localization of virtual sound sources both with and without head motion. The listeners' task was to estimate the apparent direction and distance of virtual sources (broadband noise) presented over headphones. Stimuli were synthesized from minimum phase representations of nonindividualized directional transfer functions; binaural magnitude spectra were derived from the minimum phase estimates and ITDs were represented as a pure delay. During dynamic conditions, listeners were encouraged to move their heads; the position of the listener's head was tracked and the stimuli were synthesized in real time using a Convolvotron to simulate a stationary external sound source. ILDs and ITDs were either correctly or incorrectly correlated with head motion: (1) both ILDs and ITDs correctly correlated, (2) ILDs correct, ITD fixed at 0 deg azimuth and 0 deg elevation, (3) ITDs correct, ILDs fixed at 0 deg, 0 deg. Similar conditions were run for static conditions except that none of the cues changed with head motion. The data indicated that, compared to static conditions, head movements helped listeners to resolve confusions primarily when ILDs were correctly correlated, although a smaller effect was also seen for correct ITDs. Together with the results for static conditions, the data suggest that localization tends to be dominated by the cue that is most reliable or consistent, when reliability is defined by consistency over time as well as across frequency bands.

Verification of the technical parameters of head-only electrical stunning of pigs under commercial conditions.

PubMed

Végh, Akos; Abonyi-Tóth, Zsolt; Rafai, Pál

2010-06-01

The European Food Safety Authority recommends a minimum current of 1.3 Amps for the electrical head-only stunning of pigs. However, it is stated as well that 'the technical reference data for head-only electrical stunning of pigs such as 1.3 Amps are either rather old or worked out under experimental laboratory conditions'. This study was carried out to verify the electrical parameters of pig stunning under commercial conditions. Altogether 145 fattener pigs (body weight range: 30-150 kg, median 109 kg) were tested at four different private slaughterhouses in Hungary where head-only electrical stunners were used with different constant voltage settings. In each case the following data were recorded: individual liveweight (kg), current (A) and voltage (V) (measured with an individually developed analogue device placed in the circuit), current duration (s), effectiveness of stunning, grading of carcass. Correlations between these parameters and effectiveness were examined. Besides that, any correlation between the test parameters and impedance of head was examined. In 128 out of the 145 cases the stunning was effective (88.3%). Effectiveness was significantly related to current but not to other parameters such as voltage and duration of load. Impedance of head was not correlated with the size of the animal and the meat grading scores. Generally, it was concluded that the use of a single electrical parameter (e.g. a minimum current of 1.3 A) as a prerequisite of good stunning is not ideal.

A Case Study Analysis: The Effects of Professional Learning Communities on Head Start Teachers' Preparedness

ERIC Educational Resources Information Center

Lachowicz, Shana

2017-01-01

Head Start (HS) is a nationally known program for young children and continues to serve the most vulnerable children and families. HS teachers are required to have a minimum degree status and a certain number of Professional Development (PD) hours. However, teachers continue to struggle with preparedness and effectiveness. The problem is that HS…

Comparison of nonrigid and semirigid airships

NASA Technical Reports Server (NTRS)

Stapfer,

1922-01-01

One of the main subjects of airship science consists in establishing cooperation between two vertical forces, the buoyancy of the air and the attraction of gravity. The mechanism for establishing this cooperation must have the minimum weight and offer the minimum head resistance. Starting with this principle, let us consider what improvements can be made in the present type of non-rigid airships.

High temperature, high intensity solar array. [for Venus Radar Mapper mission

NASA Technical Reports Server (NTRS)

Smith, B. S.; Brooks, G. R.; Pinkerton, R.

1985-01-01

The solar array for the Venus Radar Mapper mission will operate in the high temperature, high intensity conditions of a low Venus orbit environment. To fulfill the performance requirements in this environment at minimum cost and mass while maximizing power density and packing factor on the panel surface, several features were introduced into the design. These features included the use of optical surface reflectors (OSR's) to reduce the operating temperature; new adhesives for conductive bonding of OSR's to avoid electrostatic discharges; custom-designed large area cells and novel shunt diode circuit and panel power harness configurations.

Minimum five-year follow-up wear measurement of longevity highly cross-linked polyethylene cup against cobalt-chromium or zirconia heads.

PubMed

Nakahara, Ichiro; Nakamura, Nobuo; Nishii, Takashi; Miki, Hidenobu; Sakai, Takashi; Sugano, Nobuhiko

2010-12-01

We investigated the efficacy of combining highly cross-linked polyethylene with ceramic heads on further reduction in polyethylene wear compared with the combination with cobalt-chromium heads via PolyWare computer-assisted method. A prospective cohort study was performed on 102 cementless total hip arthroplasties using Longevity (Zimmer, Warsaw, Ind) highly cross-linked polyethylene liners. Either 26-mm zirconia heads or 26-mm cobalt-chromium heads were randomly used in 51 hips each. At a mean follow-up of 6.7 years, no significant differences were identified between the groups for total penetration rate and steady-state wear rate. Osteolysis was not observed in any hips in either group. In conclusion, no advantage was seen for the 26-mm zirconia head compared with the 26-mm cobalt-chromium head in this period. Copyright © 2010 Elsevier Inc. All rights reserved.

Influence of slope on fire spread rate

Treesearch

B.W. Butler; W.R. Anderson; E.A. Catchpole

2007-01-01

Data demonstrate the effect of slope on heading and backing fires burning through woody fuels. The data indicate that the upper limit of heading fire rate of spread is defined by the rate of spread up a vertical fuel array, and the lower limit is defined by the rate of spread of a backing fire burning downslope. The minimum spread rate is found to occur at nominally --...

Effects of radio transmitters on the behavior of Red-headed Woodpeckers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vukovich, Mark; Kilgo, John, C.

2009-05-01

ABSTRACT. Previous studies have revealed that radio-transmitters may affect bird behaviors, including feeding rates, foraging behavior, vigilance, and preening behavior. In addition, depending on the method of attachment, transmitters can potentially affect the ability of cavity-nesting birds to use cavities. Our objective was to evaluate effects of transmitters on the behavior of and use of cavities byRed-headedWoodpeckers (Melanerpes erythrocephalus). Using backpack harnesses, we attached 2.1-g transmitter packages that averaged 3.1% of body weight (range = 2.5–3.6%) to Red-headed Woodpeckers. We observed both radio-tagged (N = 23) and nonradio-tagged (N = 28) woodpeckers and determined the percentage of time spent engagedmore » in each of five behaviors: flight, foraging, perching, preening, and territorial behavior. We found no difference between the two groups in the percentage of time engaged in each behavior. In addition, we found that transmitters had no apparent effect on use of cavities for roosting by radio-tagged woodpeckers (N = 25).We conclude that backpack transmitters weighing less than 3.6% of body weight had no impact on either their behavior or their ability to use cavities.« less

Effects of radio transmitters on the behavior of Red-headed Woodpeckers.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vukovich, Mark; Kilgo, John, C.

ABSTRACT. Previous studies have revealed that radio-transmitters may affect bird behaviors, including feeding rates, foraging behavior, vigilance, and preening behavior. In addition, depending on the method of attachment, transmitters can potentially affect the ability of cavity-nesting birds to use cavities. Our objective was to evaluate effects of transmitters on the behavior of and use of cavities byRed-headedWoodpeckers (Melanerpes erythrocephalus). Using backpack harnesses, we attached 2.1-g transmitter packages that averaged 3.1% of body weight (range = 2.5–3.6%) to Red-headed Woodpeckers. We observed both radio-tagged (N = 23) and nonradio-tagged (N = 28) woodpeckers and determined the percentage of time spent engagedmore » in each of five behaviors: flight, foraging, perching, preening, and territorial behavior. We found no difference between the two groups in the percentage of time engaged in each behavior. In addition, we found that transmitters had no apparent effect on use of cavities for roosting by radio-tagged woodpeckers (N = 25).We conclude that backpack transmitters weighing less than 3.6% of body weight had no impact on either their behavior or their ability to use cavities.« less

An Adaptive Clustering Approach Based on Minimum Travel Route Planning for Wireless Sensor Networks with a Mobile Sink

PubMed Central

Tang, Jiqiang; Yang, Wu; Zhu, Lingyun; Wang, Dong; Feng, Xin

2017-01-01

In recent years, Wireless Sensor Networks with a Mobile Sink (WSN-MS) have been an active research topic due to the widespread use of mobile devices. However, how to get the balance between data delivery latency and energy consumption becomes a key issue of WSN-MS. In this paper, we study the clustering approach by jointly considering the Route planning for mobile sink and Clustering Problem (RCP) for static sensor nodes. We solve the RCP problem by using the minimum travel route clustering approach, which applies the minimum travel route of the mobile sink to guide the clustering process. We formulate the RCP problem as an Integer Non-Linear Programming (INLP) problem to shorten the travel route of the mobile sink under three constraints: the communication hops constraint, the travel route constraint and the loop avoidance constraint. We then propose an Imprecise Induction Algorithm (IIA) based on the property that the solution with a small hop count is more feasible than that with a large hop count. The IIA algorithm includes three processes: initializing travel route planning with a Traveling Salesman Problem (TSP) algorithm, transforming the cluster head to a cluster member and transforming the cluster member to a cluster head. Extensive experimental results show that the IIA algorithm could automatically adjust cluster heads according to the maximum hops parameter and plan a shorter travel route for the mobile sink. Compared with the Shortest Path Tree-based Data-Gathering Algorithm (SPT-DGA), the IIA algorithm has the characteristics of shorter route length, smaller cluster head count and faster convergence rate. PMID:28445434

45 CFR 1306.33 - Home-based program option.

Code of Federal Regulations, 2010 CFR

2010-10-01

... necessary to meet the minimums stated above. Medical or social service appointments may not replace home... for the children is to emphasize peer group interaction through age appropriate activities in a Head...

42 CFR 84.172 - Breathing tubes; minimum requirements.

Code of Federal Regulations, 2011 CFR

2011-10-01

...) Restriction of free head movement; (b) Disturbance of the fit of facepieces, mouthpieces, hoods, or helmets; (c) Interference with the wearer's activities; and (d) Shutoff of airflow due to kinking, or from...

42 CFR 84.172 - Breathing tubes; minimum requirements.

Code of Federal Regulations, 2010 CFR

2010-10-01

...) Restriction of free head movement; (b) Disturbance of the fit of facepieces, mouthpieces, hoods, or helmets; (c) Interference with the wearer's activities; and (d) Shutoff of airflow due to kinking, or from...

42 CFR 84.172 - Breathing tubes; minimum requirements.

Code of Federal Regulations, 2012 CFR

2012-10-01

...) Restriction of free head movement; (b) Disturbance of the fit of facepieces, mouthpieces, hoods, or helmets; (c) Interference with the wearer's activities; and (d) Shutoff of airflow due to kinking, or from...

42 CFR 84.172 - Breathing tubes; minimum requirements.

Code of Federal Regulations, 2014 CFR

2014-10-01

...) Restriction of free head movement; (b) Disturbance of the fit of facepieces, mouthpieces, hoods, or helmets; (c) Interference with the wearer's activities; and (d) Shutoff of airflow due to kinking, or from...

42 CFR 84.172 - Breathing tubes; minimum requirements.

Code of Federal Regulations, 2013 CFR

2013-10-01

...) Restriction of free head movement; (b) Disturbance of the fit of facepieces, mouthpieces, hoods, or helmets; (c) Interference with the wearer's activities; and (d) Shutoff of airflow due to kinking, or from...

Pi meson radiotherapy for advanced head and neck neoplasms: preliminary results.

PubMed

Khan, K M; Bush, S; Herzon, F; Klingerman, M M

1981-01-01

Under the auspices of the University of New Mexico Cancer Research and Treatment Center, trials are under way at the Los Alamos Meson Physics Facility to evaluate the effects of pi meson irradiation on locally advanced human tumors. This paper summarizes the preliminary results in patients with locally advanced head and neck tumors treated under Phase 1 and Phase II studies. A total of 26 patients were treated between June 1977 and May 1979 with a minimum follow-up of 9 months and a maximum follow-up of 33 months. Sites of disease included the oropharynx in 10 cases (base of tongue in 7, tonsil in 2, and pharyngoepiglottic fold in 1), the supraglottic larynx in 4, the nasopharynx in 5, the oral cavity in 4, the hypopharynx in 2, and the sublingual salivary gland in 1. Twelve of the 26 patients are alive, and 10 survive with no evidence of disease. Doses employed ranged from a minimum of 1,000 peak pion rad in 7 fractions over 9 days to a maximum of 5,4000 peak pion rad in 51 fractions of 89 days. The minimum dose employed for any patients treated with peak pions alone was 3,000 rad. These data are analyzed according to dose, sit, histology, tumor response, local control, and survival. Results from these cases form the basis of the Phase III randomized trials for advanced squamous-cell carcinomas of the head and neck, which are currently in progress.

Flight performance, energetics and water turnover of tippler pigeons with a harness and dorsal load

USGS Publications Warehouse

Gessaman, J.A.; Workman, G.W.; Fuller, M.R.

1991-01-01

We measured carbon dioxide production and water efflux of 12 tippler pigeons (Columba spp.) during seven experimental flights using the doubly labeled water (DLW) method. Prior to the experiment birds were randomly assigned to one of two groups. One group flew as controls (no load or harness) on all seven flights. The other group wore a harness on two flights, a dorsal load/harness package (weighing about 5% of a bird's mass) on two flights, and they were without a load in three flights. Flight duration of pigeons with only a harness and with a dorsal load/harness package was 21 and 26% less, respectively, than the controls. Pigeons wearing a harness, or wearing a dorsal load/harness package lost water 50-90%, and 57-100% faster, respectively, than control pigeons. The mean CO2 production of pigeons wearing a harness or a load/harness package was not significantly different than pigeons without a harness or load. The small sample sizes and large variability in DLW measuremets precluded a good test of the energetic cost of flying with a harness and dorsal load.

Flight performance energetics and water turnovers of Tippler Pigeons with a harness and doorsal load

USGS Publications Warehouse

Gessaman, James A.; Workman, Gar W.; Fuller, Mark R.

1991-01-01

We measured carbon dioxide production and water efflux of 12 tippler pigeons (Columba spp.) during seven experimental flights using the doubly labeled water (DLW) method. Prior to the experiment birds were randomly assigned to one of two groups. One group flew as controls (no load or harness) on all seven flights. The other group wore a harness on two flights, a dorsal load/harness package (weighing about 5% of a birda??s mass) on two flights, and they were without a load in three flights. Plight duration of pigeons with only a harness and with a dorsal load/harness package was 21 and 26% less, respectively, than the controls. Pigeons wearing a harness, or wearing a dorsal load/harness package lost water 50-90%, and 57-100% faster, respectively, than control pigeons. The mean CO, production of pigeons wearing a harness or a load/harness package was not significantly different than pigeons without a harness or load. The small sample sizes and large variability in DLW measurements precluded a good test of the energetic cost of flying with a harness and dorsal load.

Head rice rate measurement based on concave point matching

PubMed Central

Yao, Yuan; Wu, Wei; Yang, Tianle; Liu, Tao; Chen, Wen; Chen, Chen; Li, Rui; Zhou, Tong; Sun, Chengming; Zhou, Yue; Li, Xinlu

2017-01-01

Head rice rate is an important factor affecting rice quality. In this study, an inflection point detection-based technology was applied to measure the head rice rate by combining a vibrator and a conveyor belt for bulk grain image acquisition. The edge center mode proportion method (ECMP) was applied for concave points matching in which concave matching and separation was performed with collaborative constraint conditions followed by rice length calculation with a minimum enclosing rectangle (MER) to identify the head rice. Finally, the head rice rate was calculated using the sum area of head rice to the overall coverage of rice. Results showed that bulk grain image acquisition can be realized with test equipment, and the accuracy rate of separation of both indica rice and japonica rice exceeded 95%. An increase in the number of rice did not significantly affect ECMP and MER. High accuracy can be ensured with MER to calculate head rice rate by narrowing down its relative error between real values less than 3%. The test results show that the method is reliable as a reference for head rice rate calculation studies. PMID:28128315

Heat radiation approach for harnessing heat of the cook stove to generate electricity for lighting system and charging of mobile phone

NASA Astrophysics Data System (ADS)

Muñoz, Rodrigo C., Jr.; Manansala, Chad Deo G.

2018-01-01

This study is based on the potential of thermoelectric coupling such as the thermoelectric cooler module. A thermoelectric cooler converts the heat coming from the cook stove into electricity and store in a battery. A dc-dc boost converter will be used to produce enough voltage to light a minimum house dwelling or charge phone battery. This device will be helpful to those that faces a problem on electricity especially in the isolated areas. The study aims (1) to harness heat from the cook stove up to 110 °C (2) To automatically cool-off the system to protect the thermoelectric cooler from damage due to excessive heat using an electronic solenoid; (3) To store energy harnessed in the battery; (4) To amplify the output voltages of the battery using DC to DC boost converter for lighting system and charging of mobile phone battery. From various tests conducted, it can fully charge a mobile phone in 3 hours observing the unit’s battery voltage drop from 4.06V to 3.98V. In the testing it used different orientation of steel rod by conduction to transfer heat and by radiation through tubular steel with its different dimensions. Most recent testing proved that the 2x2x9 tubular steel by radiation had the best result. The temperature reached more than a hundred degree Celsius that met the objective. The test resulted of boosting the voltage of the battery output from 3.7V to 4.96V on the average. The boosted voltage decrease as the system’s cool-off mechanism operated when the temperature reached above 110 degree Celsius decreasing output voltage to 0.8V resulting the boosted voltage to drop to zero. Therefore, the proponents concluded that heat waste can be converted to electrical energy by harnessing heat through radiation, with the help of TEC that generates voltage for lighting and can be boosted to be used for mobile charging. Furthermore, the study proved that the excess heat can damaged the TEC which was prevented by using of cooling-off mechanism, making it more useful for longer time.

Facial expressions recognition with an emotion expressive robotic head

NASA Astrophysics Data System (ADS)

Doroftei, I.; Adascalitei, F.; Lefeber, D.; Vanderborght, B.; Doroftei, I. A.

2016-08-01

The purpose of this study is to present the preliminary steps in facial expressions recognition with a new version of an expressive social robotic head. So, in a first phase, our main goal was to reach a minimum level of emotional expressiveness in order to obtain nonverbal communication between the robot and human by building six basic facial expressions. To evaluate the facial expressions, the robot was used in some preliminary user studies, among children and adults.

Radiology response in the emergency department during a mass casualty incident: a retrospective study of the two terrorist attacks on 22 July 2011 in Norway.

PubMed

Young, Victoria Solveig; Eggesbø, Heidi B; Gaarder, Christine; Næss, Pål Aksel; Enden, Tone

2017-07-01

To describe the use of radiology in the emergency department (ED) in a trauma centre during a mass casualty incident, using a minimum acceptable care (MAC) strategy in which CT was restricted to potentially severe head injuries. We retrospectively studied the initial use of imaging on patients triaged to the trauma centre following the twin terrorist attacks in Norway on 22 July 2011. Nine patients from the explosion and 15 from the shooting were included. Fourteen patients had an Injury Severity Score >15. During the first 15 h, 22/24 patients underwent imaging in the ED. All 15 gunshot patients had plain films taken in the ED, compared to three from the explosion. A CT was performed in 18/24 patients; ten of these were completed in the ED and included five non-head CTs, the latter representing deviations from the MAC strategy. No CT referrals were delayed or declined. Mobilisation of radiology personnel resulted in a tripling of the staff. Plain film and CT capacity was never exceeded despite deviations from the MAC strategy. An updated disaster management plan will require the radiologist to cancel non-head CTs performed in the ED until no additional MCI patients are expected. • Minimum acceptable care (MAC) should replace normal routines in mass casualty incidents. • MAC implied reduced use of imaging in the emergency department (ED). • CT in ED was restricted to suspected severe head injuries during MAC. • The radiologist should cancel all non-head CTs in the ED during MAC.

The Optical Harness: a light-weight EMI-immune replacement for legacy electrical wiring harnesses

NASA Astrophysics Data System (ADS)

Stark, Jason B.; Jackson, B. Scott; Trethewey, William

2006-05-01

Electrical wiring harnesses have been used to interconnect control and communication equipment in mobile platforms for over a century. Although they have served this function successfully, they have three problems that are inherent in their design: they are mechanically heavy and stiff, and they are prone to electrical faults, including arcing and Electro-Magnetic Interference (EMI), and they are difficult to maintain when faults occur. These properties are all aspects of the metallic conductors used to build the harnesses. The Optical Harness TM is a photonic replacement for the legacy electrical wiring harness. The Optical Harness TM uses light-weight optical fiber to replace signal wires in an electrical harness. The original electrical connections to the equipment remain, making the Optical Harness TM a direct replacement for the legacy wiring harness. In the backshell of each connector, the electrical signals are converted to optical, and transported on optical fiber, by a deterministic, redundant and fault-tolerant optical network. The Optical Harness TM: * Provides weight savings of 40-50% and unsurpassed flexibility, relative to legacy signal wiring harnesses; * Carries its signals on optical fiber that is free from arcing, EMI, RFI and susceptibility to HPM weapons; * Is self-monitoring during operation, providing non-intrusive predictive and diagnostic capabilities.

Characterization of Noise Signatures of Involuntary Head Motion in the Autism Brain Imaging Data Exchange Repository

PubMed Central

Caballero, Carla; Mistry, Sejal; Vero, Joe; Torres, Elizabeth B

2018-01-01

The variability inherently present in biophysical data is partly contributed by disparate sampling resolutions across instrumentations. This poses a potential problem for statistical inference using pooled data in open access repositories. Such repositories combine data collected from multiple research sites using variable sampling resolutions. One example is the Autism Brain Imaging Data Exchange repository containing thousands of imaging and demographic records from participants in the spectrum of autism and age-matched neurotypical controls. Further, statistical analyses of groups from different diagnoses and demographics may be challenging, owing to the disparate number of participants across different clinical subgroups. In this paper, we examine the noise signatures of head motion data extracted from resting state fMRI data harnessed under different sampling resolutions. We characterize the quality of the noise in the variability of the raw linear and angular speeds for different clinical phenotypes in relation to age-matched controls. Further, we use bootstrapping methods to ensure compatible group sizes for statistical comparison and report the ranges of physical involuntary head excursions of these groups. We conclude that different sampling rates do affect the quality of noise in the variability of head motion data and, consequently, the type of random process appropriate to characterize the time series data. Further, given a qualitative range of noise, from pink to brown noise, it is possible to characterize different clinical subtypes and distinguish them in relation to ranges of neurotypical controls. These results may be of relevance to the pre-processing stages of the pipeline of analyses of resting state fMRI data, whereby head motion enters the criteria to clean imaging data from motion artifacts. PMID:29556179

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gorlov, A.M.

This report contains conclusive results of the research project entitled ``Further Development of the Pneumatic Method to Harness Hydropower and its Experimental Implementation in the State of Maine`` sponsored by the US Department of Energy (Contract DE-FG02-91ER12113). The results obtained by this research are considerably beyond the original goals anticipated by the contract which were a theoretical study of the method only and its possible applications. In fact, the success of the analytical research program has allowed us to move on to development, construction and testing of a physical model of the hydro-air power converter and, subsequently, to development ofmore » a well equipped hydro-pneumatic power laboratory at Northeastern University. Photographs la and 2a show both the laboratory and the model. Good performance of the model proves that the hydro-pneumatic concept holds much promise for development of an ecologically safe and commercially attractive novel approach to harnessing ultra low-head hydropower. As a result, private companies have started to support this new technology, and to invest money in its further development and construction of demonstration power plants (Appendix 1). Visitors at the Northeastern University laboratory often praise this new technique, as is attested by the articles in the Wall Street Journal (Appendix 2) and the Technology Review (Appendix 3).« less

On-Orbit Evaluation of a New Treadmill Harness for Improved Crewmember Comfort and Load Distribution

NASA Technical Reports Server (NTRS)

Perusek, G. P.; Sheehan, C. C.; Savina, M. C.; Owings, T. M.; Davis, B. L.; Ryder, J. W.

2011-01-01

The current design of the International Space Station (ISS) Treadmill Harness has been reported to cause pain and discomfort to crewmembers during exercise. The Harness Station Development Test Objective (SDTO) provided participating crewmembers (n = 6) with a new harness design, the "Glenn Harness," to evaluate for comfort and loading as compared to the current Treadmill Harness. A novel suite of load-sensing instrumentation was developed to noninvasively measure load distribution and provided a first-ever quantification of actual dynamic loads during treadmill exercise. In addition, crew debriefs provided feedback on harness preference and overall impressions. Conclusions: Post-flight analysis in returned Glenn Harnesses (n = 3) showed minimal wear and tear. Four of the six subjects found the Glenn Harness to be more comfortable in this on-orbit, side-by-side comparison as measured by the crew comfort questionnaire and crew debriefs. Specific areas for improvement have been identified, and forward recommendations will be provided to the Human Research Program. The protocol developed for the SDTO provided valuable insight into crew comfort issues, design improvements, and loading preferences for exercise harnessing, which lays the groundwork for better harnessing systems and training protocols.

Minimum required capture radius in a coplanar model of the aerial combat problem

NASA Technical Reports Server (NTRS)

Breakwell, J. V.; Merz, A. W.

1977-01-01

Coplanar aerial combat is modeled with constant speeds and specified turn rates. The minimum capture radius which will always permit capture, regardless of the initial conditions, is calculated. This 'critical' capture radius is also the maximum range which the evader can guarantee indefinitely if the initial range, for example, is large. A composite barrier is constructed which gives the boundary, at any heading, of relative positions for which the capture radius is less than critical.

The moving minimum audible angle is smaller during self motion than during source motion

PubMed Central

Brimijoin, W. Owen; Akeroyd, Michael A.

2014-01-01

We are rarely perfectly still: our heads rotate in three axes and move in three dimensions, constantly varying the spectral and binaural cues at the ear drums. In spite of this motion, static sound sources in the world are typically perceived as stable objects. This argues that the auditory system—in a manner not unlike the vestibulo-ocular reflex—works to compensate for self motion and stabilize our sensory representation of the world. We tested a prediction arising from this postulate: that self motion should be processed more accurately than source motion. We used an infrared motion tracking system to measure head angle, and real-time interpolation of head related impulse responses to create “head-stabilized” signals that appeared to remain fixed in space as the head turned. After being presented with pairs of simultaneous signals consisting of a man and a woman speaking a snippet of speech, normal and hearing impaired listeners were asked to report whether the female voice was to the left or the right of the male voice. In this way we measured the moving minimum audible angle (MMAA). This measurement was made while listeners were asked to turn their heads back and forth between ± 15° and the signals were stabilized in space. After this “self-motion” condition we measured MMAA in a second “source-motion” condition when listeners remained still and the virtual locations of the signals were moved using the trajectories from the first condition. For both normal and hearing impaired listeners, we found that the MMAA for signals moving relative to the head was ~1–2° smaller when the movement was the result of self motion than when it was the result of source motion, even though the motion with respect to the head was identical. These results as well as the results of past experiments suggest that spatial processing involves an ongoing and highly accurate comparison of spatial acoustic cues with self-motion cues. PMID:25228856

Periacetabular osteotomy and combined femoral head-neck junction osteochondroplasty: a minimum two-year follow-up cohort study.

PubMed

Nassif, Nader A; Schoenecker, Perry L; Thorsness, Robert; Clohisy, John C

2012-11-07

Proximal femoral deformities and overcorrection of the acetabulum both can result in secondary femoroacetabular impingement and suboptimal clinical results after periacetabular osteotomy. The purpose of the present study was to determine the rate of complications, the need for reoperations, radiographic correction, and hip function among patients who underwent periacetabular osteotomy and combined femoral head-neck osteochondroplasty as compared with those who underwent periacetabular osteotomy alone. Patients who underwent periacetabular osteotomy with or without osteochondroplasty of the femoral head-neck junction were evaluated retrospectively after a minimum duration of follow-up of two years. We compared the two groups with regard to the modified Harris hip score, radiographic correction, complications, and reoperations. Forty patients (forty hips) who underwent periacetabular osteotomy in conjunction with a femoral head-neck osteochondroplasty were compared with forty-eight patients (forty-eight hips) who underwent an isolated periacetabular osteotomy. Patients were evaluated after a mean duration of follow-up of 3.4 years (range, 2.0 to 9.7 years). Preoperatively, the modified Harris hip score (and standard deviation) was 64.3 ± 13.2 for the study group and 63.2 ± 13.4 for the comparison group. At the time of the latest follow-up, the modified Harris hip score was not significantly different between the study group and the comparison group (p = 0.17). Patients demonstrated equivalent preoperative deformities and postoperative acetabular radiographic parameters. There was a significant decrease in the alpha angle and improvement in head-neck offset in the study group. There was one reoperation for secondary impingement and/or labral pathology in the study group, compared with four reoperations in the comparison group. There were no adhesions requiring surgery, femoral neck fractures, instances of osteonecrosis, or increases in heterotopic ossification in the study group. Femoral head-neck junction osteochondroplasty performed concurrently with a periacetabular osteotomy for the treatment of symptomatic acetabular dysplasia and associated femoral head-neck junction deformities is not associated with an increased complication rate. This combined procedure provides effective correction of associated femoral head-neck deformities and produces similar early functional outcomes when compared with isolated periacetabular osteotomy. Therapeutic Level III.

Integration of a Copper-Containing Biohybrid (CuHARS) with Cellulose for Subsequent Degradation and Biomedical Control

PubMed Central

Karan, Anik; Darder, Margarita; Kansakar, Urna; Norcross, Zach

2018-01-01

We previously described the novel synthesis of a copper high-aspect ratio structure (CuHARS) biohybrid material using cystine. While extremely stable in water, CuHARS is completely (but slowly) degradable in cellular media. Here, integration of the CuHARS into cellulose matrices was carried out to provide added control for CuHARS degradation. Synthesized CuHARS was concentrated by centrifugation and then dried. The weighed mass was re-suspended in water. CuHARS was stable in water for months without degradation. In contrast, 25 μg/mL of the CuHARS in complete cell culture media was completely degraded (slowly) in 18 days under physiological conditions. Stable integration of CuHARS into cellulose matrices was achieved through assembly by mixing cellulose micro- and nano-fibers and CuHARS in an aqueous (pulp mixture) phase, followed by drying. Additional materials were integrated to make the hybrids magnetically susceptible. The cellulose-CuHARS composite films could be transferred, weighed, and cut into usable pieces; they maintained their form after rehydration in water for at least 7 days and were compatible with cell culture studies using brain tumor (glioma) cells. These studies demonstrate utility of a CuHARS-cellulose biohybrid for applied applications including: (1) a platform for biomedical tracking and (2) integration into a 2D/3D matrix using natural products (cellulose). PMID:29693569

Airborne Optical Communications Demonstrator Design And Preflight Test Results

NASA Technical Reports Server (NTRS)

Biswas, Abhijit; Page, N.; Neal, J.; Zhu, D.; Wright, M.; Ovtiz, G.; Farr, W. H.; Hernnzati, H.

2005-01-01

A second generation optical communications demonstrator (OCD-2) intended for airborne applications like air-to-ground and air-to-air optical links is under development at JPL. This development provides the capability for unidirectional high data rate (2.5-Gbps) transmission at 1550-nm, with the ability to receive an 810-nm beacon to aid acquisition pointing and tracking. The transmitted beam width is nominally 200-(micro)rad. A 3x3 degree coarse field-of-view (FOV) acquisition sensor with a much smaller 3-mrad FOV tracking sensor is incorporated. The OCD-2 optical head will be integrated to a high performance gimbal turret assembly capable of providing pointing stability of 5- microradians from an airborne platform. Other parts of OCD-2 include a cable harness, connecting the optical head in the gimbal turret assembly to a rugged electronics box. The electronics box will house: command and control processors, laser transmitter, data-generation-electronics, power conversion/distribution hardware and state-of-health monitors. The entire assembly will be integrated and laboratory tested prior to a planned flight demonstrations.

Tape/head interface study

NASA Technical Reports Server (NTRS)

1983-01-01

Existing high energy tapes, high track density heads, and transport guidance techniques were evaluated and characterized to enable these technologies to be employed in future spacecraft recorders with high confidence. The results of these study efforts demonstrated tracking accuracy tape and head density that will support spacecraft recorders with data rates of a minimum of 150 Mbps and storage capacities ranging from 10 to the 10th to 10 to the 11th bits. Seven high energy tapes of either .25 in width, 1.00 in width, or both, were tested. All tapes were tested at the same speed (30 ips) and the same packing density (33 KBI). The performance of all 1 in tapes was considered superior.

Robust human machine interface based on head movements applied to assistive robotics.

PubMed

Perez, Elisa; López, Natalia; Orosco, Eugenio; Soria, Carlos; Mut, Vicente; Freire-Bastos, Teodiano

2013-01-01

This paper presents an interface that uses two different sensing techniques and combines both results through a fusion process to obtain the minimum-variance estimator of the orientation of the user's head. Sensing techniques of the interface are based on an inertial sensor and artificial vision. The orientation of the user's head is used to steer the navigation of a robotic wheelchair. Also, a control algorithm for assistive technology system is presented. The system is evaluated by four individuals with severe motors disability and a quantitative index was developed, in order to objectively evaluate the performance. The results obtained are promising since most users could perform the proposed tasks with the robotic wheelchair.

Robust Human Machine Interface Based on Head Movements Applied to Assistive Robotics

PubMed Central

Perez, Elisa; López, Natalia; Orosco, Eugenio; Soria, Carlos; Mut, Vicente; Freire-Bastos, Teodiano

2013-01-01

This paper presents an interface that uses two different sensing techniques and combines both results through a fusion process to obtain the minimum-variance estimator of the orientation of the user's head. Sensing techniques of the interface are based on an inertial sensor and artificial vision. The orientation of the user's head is used to steer the navigation of a robotic wheelchair. Also, a control algorithm for assistive technology system is presented. The system is evaluated by four individuals with severe motors disability and a quantitative index was developed, in order to objectively evaluate the performance. The results obtained are promising since most users could perform the proposed tasks with the robotic wheelchair. PMID:24453877

Camouflage design and head measurement characteristic of Indonesian armoured vehicle helmet

NASA Astrophysics Data System (ADS)

Sya'bana, Yukhi Mustaqim Kusuma; Sanjaya, K. H.

2017-01-01

In this paper discussed camouflage design helmet for armored vehicles with comparing head measurement of Indonesian anthropometric. Design process conduct with considering of design aspects involves function, materials, operational, technology, user, and appearance (camouflage). As an application of Indonesian National Army that qualifies factors needs: safety, comfort, practical and service. MIL-H-44099A Military Specification: Helmet, Ground Troops And Parachutists is minimum limitation standard of military helmet production. Head measurement for product design process guide is presented. Model simulation and helmet measurement using the design for ego and design for more types ergonomics concept. Appearance shape concept is engaging camouflage towards background and environment to deceive enemy viewpoint. Helmet prototype has tested ergonomically to an Indonesian National Army soldier and stated that the helmet size is a comfort and fitted on the head when in use.

Ratio of shear viscosity to entropy density in multifragmentation of Au + Au

NASA Astrophysics Data System (ADS)

Zhou, C. L.; Ma, Y. G.; Fang, D. Q.; Li, S. X.; Zhang, G. Q.

2012-06-01

The ratio of the shear viscosity (η) to entropy density (s) for the intermediate energy heavy-ion collisions has been calculated by using the Green-Kubo method in the framework of the quantum molecular dynamics model. The theoretical curve of η/s as a function of the incident energy for the head-on Au + Au collisions displays that a minimum region of η/s has been approached at higher incident energies, where the minimum η/s value is about 7 times Kovtun-Son-Starinets (KSS) bound (1/4π). We argue that the onset of minimum η/s region at higher incident energies corresponds to the nuclear liquid gas phase transition in nuclear multifragmentation.

Effect of lungeing on head and pelvic movement asymmetry in horses with induced lameness.

PubMed

Rhodin, M; Pfau, T; Roepstorff, L; Egenvall, A

2013-12-01

Lungeing is an important part of lameness examinations, since the circular path enforced during lungeing is thought to accentuate low grade lameness. However, during lungeing the movement of sound horses becomes naturally asymmetric, which may mimic lameness. Also, compensatory movements in the opposite half of the body may mimic lameness. The aim of this study was to objectively study the presence of circle-dependent and compensatory movement asymmetries in horses with induced lameness. Ten horses were trotted in a straight line and lunged in both directions on a hard surface. Lameness was induced (reversible hoof pressure) in each limb, one at a time, in random order. Vertical head and pelvic movements were measured with body-mounted, uni-axial accelerometers. Differences between maximum and minimum height observed during/after left and right stance phases for the head (HDmax, HDmin) and pelvis (PDmax, PDmin) were measured. Mixed models were constructed to study the effect of lungeing direction and induction, and to quantify secondary compensatory asymmetry mechanisms in the forelimbs and hind limbs. Head and pelvic movement symmetries were affected by lungeing. Minimum pelvic height difference (PDmin) changed markedly, increasing significantly during lungeing, giving the impression of inner hind limb lameness. Primary hind limb lameness induced compensatory head movement, which mimicked an ipsilateral forelimb lameness of almost equal magnitude to the primary hind limb lameness. This could contribute to difficulty in correctly detecting hind limb lameness. Induced forelimb lameness caused both a compensatory contralateral (change in PDmax) and an ipsilateral (change in PDmin) hind limb asymmetry, potentially mimicking hind limb lameness, but of smaller magnitude. Both circle-dependent and compensatory movement mechanisms must be taken into account when evaluating lameness. Copyright © 2013 Elsevier Ltd. All rights reserved.

Trunnionosis: Does Head Size Affect Fretting and Corrosion in Total Hip Arthroplasty?

PubMed

Del Balso, Christopher; Teeter, Matthew G; Tan, Sok Chuen; Howard, James L; Lanting, Brent A

2016-10-01

Wear and tribocorrosion at the modular head-neck taper interface may be a cause of failure in metal-on-polyethylene total hip arthroplasty (THA). The present investigation endeavored to elucidate the effect of femoral head diameter on fretting and corrosion in retrieved head-neck tapers. A retrieval analysis of THA prostheses in vivo for a minimum of 1 year was performed. Twenty-three femoral heads of 32-mm diameter were matched with 28-mm heads based on time in vivo and head length (-3 mm to +8 mm). All included implants featured a single taper design from a single manufacturer. Fretting and corrosion damage scoring was performed for each implant under stereomicroscopic visualization. Head diameter was observed to affect fretting (P = .01), with 32-mm femoral heads exhibiting greater total fretting scores than 28-mm heads. Fretting damage was greatest (P = .01) in the central concentric zone of the femoral head bore tapers, regardless of head diameter, length, or stem offset. No significant effect on total corrosion scores was observed for any head or stem variable. Retrieved implant total corrosion scores were positively correlated (ρ = 0.51, P < .001) with implantation time. Increased femoral head diameter in THA may produce greater fretting damage owing to and increased head-neck moment arm. There is no associated increase in corrosion with 28-mm and 32-mm heads of this taper design. The longer a THA prosthesis is implanted, the greater the risk of damage due to corrosion. Copyright © 2016 Elsevier Inc. All rights reserved.

75 FR 63422 - Airworthiness Directives; Embraer-Empresa Brasileira de Aeronautica S.A. Model EMB-500 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-10-15

... chafing between the same harness and the oxygen tubing. The chafing of the wiring harness against the oxygen tubing could lead to a short circuit of the wiring harness and a subsequent fire in the airplane... harness and the oxygen tubing. The chafing of the wiring harness against the oxygen tubing could lead to a...

Conservation of water for washing beef heads at harvest.

PubMed

DeOtte, R E; Spivey, K S; Galloway, H O; Lawrence, T E

2010-03-01

The objective of this research was to develop methods to conserve water necessary to cleanse beef heads prior to USDA-FSIS inspection. This was to be accomplished by establishing a baseline for the minimum amount of water necessary to adequately wash a head and application of image analysis to provide an objective measure of head cleaning. Twenty-one beef heads were manually washed during the harvest process. An average 18.75 L (2.49 SD) and a maximum of 23.88 L were required to cleanse the heads to USDA-FSIS standards. Digital images were captured before and after manual washing then evaluated for percentage red saturation using commercially available image analysis software. A decaying exponential curve extracted from these data indicated that as wash water increased beyond 20 L the impact on red saturation decreased. At 4 sigma from the mean of 18.75 L, red saturation is 16.0 percent, at which logistic regression analysis indicates 99.994 percent of heads would be accepted for inspection, or less than 1 head in 15,000 would be rejected. Reducing to 3 sigma would increase red saturation to 27.6 percent, for which 99.730 percent of heads likely would be accepted (less than 1 in 370 would be rejected). Copyright 2009 Elsevier Ltd. All rights reserved.

Dipolar interactions and miscibility in binary Langmuir monolayers with opposite dipole moments of the hydrophilic heads.

PubMed

Petrov, Jordan G; Andreeva, Tonya D; Moehwald, Helmuth

2009-04-09

We investigate unusual binary Langmuir monolayers with the same long CH3(CH2)21 hydrocarbon chains and fluorinated -O-CH2CF3 (FEE) versus nonfluorinated -O-CH2CH3 (EE) hydrophilic heads, whose opposite dipoles assist miscibility, in contrast to the equally oriented polar head dipoles of almost all natural or synthetic amphiphiles that minister to phase separation. Although two-component bulk micelles, lipid bilayers, and monolayers with fluorinated and nonfluorinated chains, which also have opposite dipoles, often show phase separation, we find complete miscibility and nonideality of the FEE-EE mixtures demonstrated via deviation of the composition dependencies of the mean molecular area at fixed surface pressure from the additivity rule. The composition dependencies of the excess molecular areas exhibit minima and maxima which show specific structural changes at particular compositions. They originate from the dipolar and steric interactions between the polar heads, because the interactions between the same chains of FEE and EE do not vary. The pi/A isotherms and the pi/X(FEE) phase diagram reveal that mixtures with molar fractions X(FEE) > or = 0.3 exist in an upright solid phase even in uncompressed state. This result is confirmed by the compressibility values and via Brewster angle microscopy, which does not show optical anisotropy at X(FEE) > or = 0.3. Comparison of the collapse and phase-transition molecular areas with literature data suggests that the upright architecture corresponds to LS-phase or S-phase with more defects as the S-phase in the pure monolayers. The mixtures with X(FEE) < 0.3 exist in tilted L2' phase at low surface pressures. Their mean molecular areas are smaller than the corresponding values in the EE film, which manifests reduction of the tilt of the EE chains with increasing FEE content. We ascribe the chain erection to partial dehydration of the EE heads caused by dipolar attraction between the EE and FEE heads. The excess free energy of mixing deltaG(exc)pi is positive but much smaller than the negative total free energy of mixing AG mix(pi) showing a spontaneous miscibility at all compositions due to an entropy increase. The analysis of the conflict between the deltaG(mix)pi minimum at molar fraction X(FEE) = 0.5 and the minimum and negative value of the excess molecular area A(pi,exc) at X(FEE) = 0.8 shows that the A(pi,exc)/X(FEE) minimum has not an electrostatic but a short-range structural origin.

Visual-vestibular cue integration for heading perception: applications of optimal cue integration theory.

PubMed

Fetsch, Christopher R; Deangelis, Gregory C; Angelaki, Dora E

2010-05-01

The perception of self-motion is crucial for navigation, spatial orientation and motor control. In particular, estimation of one's direction of translation, or heading, relies heavily on multisensory integration in most natural situations. Visual and nonvisual (e.g., vestibular) information can be used to judge heading, but each modality alone is often insufficient for accurate performance. It is not surprising, then, that visual and vestibular signals converge frequently in the nervous system, and that these signals interact in powerful ways at the level of behavior and perception. Early behavioral studies of visual-vestibular interactions consisted mainly of descriptive accounts of perceptual illusions and qualitative estimation tasks, often with conflicting results. In contrast, cue integration research in other modalities has benefited from the application of rigorous psychophysical techniques, guided by normative models that rest on the foundation of ideal-observer analysis and Bayesian decision theory. Here we review recent experiments that have attempted to harness these so-called optimal cue integration models for the study of self-motion perception. Some of these studies used nonhuman primate subjects, enabling direct comparisons between behavioral performance and simultaneously recorded neuronal activity. The results indicate that humans and monkeys can integrate visual and vestibular heading cues in a manner consistent with optimal integration theory, and that single neurons in the dorsal medial superior temporal area show striking correlates of the behavioral effects. This line of research and other applications of normative cue combination models should continue to shed light on mechanisms of self-motion perception and the neuronal basis of multisensory integration.

Behavior of sandhill cranes harnessed with different satellite transmitters

USGS Publications Warehouse

Olsen, Glenn H.; Ellis, D.H.; Landfried, S.E.; Miller, L.H.; Klugman, S.S.; Fuller, M.R.; Vermillion, C.H.

1992-01-01

The effectiveness of various attachment methods and designs of platform transmitting terminals (PTT's) was tested on captive sandhill cranes (Grus canadensis) at the Patuxent Wildlife Research Center, Laurel, Maryland, during 1989-91. Combinations of attachment and transmitter designs included neoprene cord harness with batteries separate from the transmitter (2 harness designs), Teflon ribbon harness with batteries incorporated into the transmitter package (4 transmitter models), and a package attached directly to the bird with epoxy glue only. Physical effects seen on cranes wearing PTT's ranged from skin lacerations (caused by rubbing of harness material) to no observed effects (other than feather wear). The most successful harness material and design utilized a Teflon ribbon harness with the 4 ribbon ends from the transmitter forming a neck loop and a body loop joined at the sternum. Time spent by sandhill cranes performing most activities did not change after transmitter attachment using this harness method.

Intelligent electrical harness connector assembly using Bell Helicopter Textron's 'Wire Harness Automated Manufacturing System'

NASA Astrophysics Data System (ADS)

Springer, D. W.

Bell Helicopter Textron, Incorporated (BHTI) installed two Digital Equipment Corporation PDP-11 computers and an American Can Inc. Ink Jet printer in 1980 as the cornerstone of the Wire Harness Automated Manufacturing System (WHAMS). WHAMS is based upon the electrical assembly philosophy of continuous filament harness forming. This installation provided BHTI with a 3 to 1 return-on-investment by reducing wire and cable identification cycle time by 80 percent and harness forming, on dedicated layout tooling, by 40 percent. Yet, this improvement in harness forming created a bottle neck in connector assembly. To remove this bottle neck, BHTI has installed a prototype connector assembly cell that integrates the WHAMS' data base and innovative computer technologies to cut harness connector assembly cycle time. This novel connector assembly cell uses voice recognition, laser identification, and animated computer graphics to help the electrician in the correct assembly of harness connectors.

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) Showers shall be provided with both hot and cold water. (ii) At least one shower head shall be provided... urinal. (iv) An adequate supply of toilet paper shall be provided with each toilet. (v) Adequate...

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) Showers shall be provided with both hot and cold water. (ii) At least one shower head shall be provided... urinal. (iv) An adequate supply of toilet paper shall be provided with each toilet. (v) Adequate...

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Code of Federal Regulations, 2012 CFR

2012-07-01

...) Showers shall be provided with both hot and cold water. (ii) At least one shower head shall be provided... urinal. (iv) An adequate supply of toilet paper shall be provided with each toilet. (v) Adequate...

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Showers shall be provided with both hot and cold water. (ii) At least one shower head shall be provided... urinal. (iv) An adequate supply of toilet paper shall be provided with each toilet. (v) Adequate...

30 CFR 71.402 - Minimum requirements for bathing facilities, change rooms, and sanitary flush toilet facilities.

Code of Federal Regulations, 2011 CFR

2011-07-01

...) Showers shall be provided with both hot and cold water. (ii) At least one shower head shall be provided... urinal. (iv) An adequate supply of toilet paper shall be provided with each toilet. (v) Adequate...

Low Head, Vortex Induced Vibrations River Energy Converter

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bernitsas, Michael B.; Dritz, Tad

2006-06-30

Vortex Induced Vibrations Aquatic Clean Energy (VIVACE) is a novel, demonstrated approach to extracting energy from water currents. This invention is based on a phenomenon called Vortex Induced Vibrations (VIV), which was first observed by Leonardo da Vinci in 1504AD. He called it ‘Aeolian Tones.’ For decades, engineers have attempted to prevent this type of vibration from damaging structures, such as offshore platforms, nuclear fuel rods, cables, buildings, and bridges. The underlying concept of the VIVACE Converter is the following: Strengthen rather than spoil vortex shedding; enhance rather than suppress VIV; harness rather than mitigate VIV energy. By maximizing andmore » utilizing this unique phenomenon, VIVACE takes this “problem” and successfully transforms it into a valuable resource for mankind.« less

Negative Rotation Cinch Strap.

DTIC Science & Technology

This project discloses an improved unitary parachute torso harness, having a single fastening means, wherein an auxillary tightening strap is...attached to the groin straps of said harness. Said auxillary straps are used to prevent torso rotation or harness slippage and to prevent harness elongation

Return to sports after plate fixation of humeral head fractures 65 cases with minimum 24-month follow-up.

PubMed

Ahrens, Philipp; Martetschläger, Frank; Siebenlist, Sebastian; Attenberger, Johann; Crönlein, Moritz; Biberthaler, Peter; Stöckle, Ulrich; Sandmann, Gunther H

2017-04-26

Humeral head fractures requiring surgical intervention are severe injuries, which might affect the return to sports and daily activities. We hypothesize that athletic patients will be constrained regarding their sporting activities after surgically treated humeral head fractures. Despite a long rehabilitation program physical activities will change and an avoidance of overhead activities will be noticed. Case series with 65 Patients, with a minimum follow-up of 24 months participated in this study. All patients were treated using a locking plate fixation. Their sporting activity was investigated at the time of the injury and re-investigated after an average of 3.83 years. The questionnaire setup included the evaluation of shoulder function, sporting activities, intensity, sport level and frequency evaluation. Level of evidence IV. At the time of injury 61 Patients (94%) were engaged in recreational sporting activities. The number of sporting activities declined from 26 to 23 at the follow-up examination. There was also a decline in sports frequency and duration of sports activities. The majority of patients remains active in their recreational sporting activity at a comparable duration and frequency both pre- and postoperatively. Nevertheless, shoulder centered sport activities including golf, water skiing and martial arts declined or were given up.

Moving Large Wiring-Harness Boards

NASA Technical Reports Server (NTRS)

Shepherd, Samuel D.; Gurman, Isaac

1990-01-01

Carrier for wiring-harness fabrication boards enables lone operator to move board easily and safely. Holds harness while operator fabricating, while being stored, and being transported to equipment frame for mounting. When positioned for assembly of wiring harness, board and carrier give operator easy and convenient access to wires and cables, when positioned for transfer of wiring harness to or from storage area, carrier holds board securely while moved by one person.

Silicon monoxide in the 4 micron infrared spectrum of long-period variables

NASA Technical Reports Server (NTRS)

Hinkle, K. H.; Barnes, T. G.; Lambert, D. L.; Beer, R.

1976-01-01

The first-overtone sequence of vibration-rotation transitions of the free radical silicon monoxide are shown to have extreme phase-dependent variations in the spectra of two M-type long-period variables, Omicron Ceti and R Leonis, and the mild S-type long-period variable, Chi Cygni. At maximum light, the SiO band heads are not detectable. Near minimum light, the band heads of (Si-25)O are detected in the 4-micron spectra of all three stars. The band heads of the terrestrially less abundant isotopic species, (Si-29)O and (Si-30)O, are detected in Chi Cygni. Possible explanations of the phase-dependent behavior are discussed, and the role of the stellar chromosphere is considered.

Transition of Attention in Terminal Area NextGen Operations Using Synthetic Vision Systems

NASA Technical Reports Server (NTRS)

Ellis, Kyle K. E.; Kramer, Lynda J.; Shelton, Kevin J.; Arthur, Shelton, J. J., III; Prinzel, Lance J., III; Norman, Robert M.

2011-01-01

This experiment investigates the capability of Synthetic Vision Systems (SVS) to provide significant situation awareness in terminal area operations, specifically in low visibility conditions. The use of a Head-Up Display (HUD) and Head-Down Displays (HDD) with SVS is contrasted to baseline standard head down displays in terms of induced workload and pilot behavior in 1400 RVR visibility levels. Variances across performance and pilot behavior were reviewed for acceptability when using HUD or HDD with SVS under reduced minimums to acquire the necessary visual components to continue to land. The data suggest superior performance for HUD implementations. Improved attentional behavior is also suggested for HDD implementations of SVS for low-visibility approach and landing operations.

Roofing: Don't Let What's Over Head Kill Your Bottom Line.

ERIC Educational Resources Information Center

Shannon, James W., Jr.

1983-01-01

A Colorado school district employs a professional consulting firm to give an unbiased opinion on the district's roofing needs. Built-up, single-ply, and modified asphalt roofing systems have all been utilized. Preventive maintenance keeps roofing bills to a minimum. (MLF)

Computationally-Efficient Minimum-Time Aircraft Routes in the Presence of Winds

NASA Technical Reports Server (NTRS)

Jardin, Matthew R.

2004-01-01

A computationally efficient algorithm for minimizing the flight time of an aircraft in a variable wind field has been invented. The algorithm, referred to as Neighboring Optimal Wind Routing (NOWR), is based upon neighboring-optimal-control (NOC) concepts and achieves minimum-time paths by adjusting aircraft heading according to wind conditions at an arbitrary number of wind measurement points along the flight route. The NOWR algorithm may either be used in a fast-time mode to compute minimum- time routes prior to flight, or may be used in a feedback mode to adjust aircraft heading in real-time. By traveling minimum-time routes instead of direct great-circle (direct) routes, flights across the United States can save an average of about 7 minutes, and as much as one hour of flight time during periods of strong jet-stream winds. The neighboring optimal routes computed via the NOWR technique have been shown to be within 1.5 percent of the absolute minimum-time routes for flights across the continental United States. On a typical 450-MHz Sun Ultra workstation, the NOWR algorithm produces complete minimum-time routes in less than 40 milliseconds. This corresponds to a rate of 25 optimal routes per second. The closest comparable optimization technique runs approximately 10 times slower. Airlines currently use various trial-and-error search techniques to determine which of a set of commonly traveled routes will minimize flight time. These algorithms are too computationally expensive for use in real-time systems, or in systems where many optimal routes need to be computed in a short amount of time. Instead of operating in real-time, airlines will typically plan a trajectory several hours in advance using wind forecasts. If winds change significantly from forecasts, the resulting flights will no longer be minimum-time. The need for a computationally efficient wind-optimal routing algorithm is even greater in the case of new air-traffic-control automation concepts. For air-traffic-control automation, thousands of wind-optimal routes may need to be computed and checked for conflicts in just a few minutes. These factors motivated the need for a more efficient wind-optimal routing algorithm.

14 CFR 125.211 - Seat and safety belts.

Code of Federal Regulations, 2014 CFR

2014-01-01

... emergency exit. (f) Each occupant of a seat equipped with a shoulder harness must fasten the shoulder harness during takeoff and landing, except that, in the case of crewmembers, the shoulder harness need not be fastened if the crewmember cannot perform his required duties with the shoulder harness fastened...

Influence of Gravity on Ocular Lens Position.

PubMed

Lister, Lucas J; Suheimat, Marwan; Verkicharla, Pavan K; Mallen, Edward A H; Atchison, David A

2016-04-01

We determined whether human ocular lens position is influenced by gravity. Anterior chamber depth (ACD) and lens thickness (LT) were determined with a Haag-Streit Lenstar LS900 for right eyes of participants in two age groups, with a young group of 13 participants aged 18 to 21 years (mean, 21 years; SD, 1 year) and an older group of 10 participants aged 50 to 63 years (mean, 58 years; SD, 4 years). There were two sessions for each participant separated by at least 48 hours, with one session for the usual upright head position and one session for a downwards head position. In a session, testing was done for minimum accommodation followed by testing at maximum accommodation. A drop of 2% pilocarpine nitrate was instilled, and testing was repeated after 30 minutes under minimum and maximum accommodation conditions. Gravity, manipulated through head posture, affected ACD for young adult and older adult groups but mean effects were only small, ranging from 0.04 to 0.12 mm, and for the older group required the instillation of an accommodation-stimulating drug. Gravity had a weakly significant effect on LT for the young group without accommodation or a drug, but the effect was small at 0.04 ± 0.06 mm (mean ± SD, P = 0.04). There is a small but real effect of gravity on crystalline lens position, manifested as reduction in ACD at high levels of accommodative effort with the head in a downwards position. This provides evidence of the ability of zonules to slacken during strong accommodation.

10 CFR 1046.14 - Access authorization.

Code of Federal Regulations, 2010 CFR

2010-01-01

... authorization for the highest level of classified matter to which they potentially have access. Security police... by the site security organization and approved by the Head of the Field Element. Security police officers shall possess a minimum of an “L” or DOE Secret access authorization. Security police officers...

Which is the better forecasting model? A comparison between HAR-RV and multifractality volatility

NASA Astrophysics Data System (ADS)

Ma, Feng; Wei, Yu; Huang, Dengshi; Chen, Yixiang

2014-07-01

In this paper, by taking the 5-min high frequency data of the Shanghai Composite Index as example, we compare the forecasting performance of HAR-RV and Multifractal volatility, Realized volatility, Realized Bipower Variation and their corresponding short memory model with rolling windows forecasting method and the Model Confidence Set which is proved superior to SPA test. The empirical results show that, for six loss functions, HAR-RV outperforms other models. Moreover, to make the conclusions more precise and robust, we use the MCS test to compare the performance of their logarithms form models, and find that the HAR-log(RV) has a better performance in predicting future volatility. Furthermore, by comparing the two models of HAR-RV and HAR-log(RV), we conclude that, in terms of performance forecasting, the HAR-log(RV) model is the best model among models we have discussed in this paper.

14 CFR 121.311 - Seats, safety belts, and shoulder harnesses.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Seats, safety belts, and shoulder harnesses... § 121.311 Seats, safety belts, and shoulder harnesses. (a) No person may operate an airplane unless... belt and shoulder harness that meets the applicable requirements specified in § 25.785 of this chapter...

14 CFR 121.311 - Seats, safety belts, and shoulder harnesses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Seats, safety belts, and shoulder harnesses... § 121.311 Seats, safety belts, and shoulder harnesses. (a) No person may operate an airplane unless... belt and shoulder harness that meets the applicable requirements specified in § 25.785 of this chapter...

14 CFR 121.311 - Seats, safety belts, and shoulder harnesses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Seats, safety belts, and shoulder harnesses... § 121.311 Seats, safety belts, and shoulder harnesses. (a) No person may operate an airplane unless... belt and shoulder harness that meets the applicable requirements specified in § 25.785 of this chapter...

14 CFR 137.42 - Fastening of safety belts and shoulder harnesses.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Fastening of safety belts and shoulder... AGRICULTURAL AIRCRAFT OPERATIONS Operating Rules § 137.42 Fastening of safety belts and shoulder harnesses. No... belt and shoulder harness properly secured about that person except that the shoulder harness need not...

14 CFR 137.42 - Fastening of safety belts and shoulder harnesses.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Fastening of safety belts and shoulder... AGRICULTURAL AIRCRAFT OPERATIONS Operating Rules § 137.42 Fastening of safety belts and shoulder harnesses. No... belt and shoulder harness properly secured about that person except that the shoulder harness need not...

14 CFR 137.42 - Fastening of safety belts and shoulder harnesses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Fastening of safety belts and shoulder... AGRICULTURAL AIRCRAFT OPERATIONS Operating Rules § 137.42 Fastening of safety belts and shoulder harnesses. No... belt and shoulder harness properly secured about that person except that the shoulder harness need not...

14 CFR 137.42 - Fastening of safety belts and shoulder harnesses.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Fastening of safety belts and shoulder... AGRICULTURAL AIRCRAFT OPERATIONS Operating Rules § 137.42 Fastening of safety belts and shoulder harnesses. No... belt and shoulder harness properly secured about that person except that the shoulder harness need not...

14 CFR 137.42 - Fastening of safety belts and shoulder harnesses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Fastening of safety belts and shoulder... AGRICULTURAL AIRCRAFT OPERATIONS Operating Rules § 137.42 Fastening of safety belts and shoulder harnesses. No... belt and shoulder harness properly secured about that person except that the shoulder harness need not...

14 CFR 121.311 - Seats, safety belts, and shoulder harnesses.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Seats, safety belts, and shoulder harnesses... § 121.311 Seats, safety belts, and shoulder harnesses. (a) No person may operate an airplane unless... belt and shoulder harness that meets the applicable requirements specified in § 25.785 of this chapter...

14 CFR 121.311 - Seats, safety belts, and shoulder harnesses.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Seats, safety belts, and shoulder harnesses... § 121.311 Seats, safety belts, and shoulder harnesses. (a) No person may operate an airplane unless... belt and shoulder harness that meets the applicable requirements specified in § 25.785 of this chapter...

Application of a modified harness design for attachment of radio transmitters to shorebirds

USGS Publications Warehouse

Sanzenbacher, Peter M.; Haig, Susan M.; Oring, Lewis W.

2000-01-01

Radio transmitter attachment methodology is important to the design of radio telemetry studies. In 1998, we attached 5 transmitters to a captive population of Western Sandpipers (Calidris mauri) and 7 transmitters to wild Killdeer (Charadriusv ociferus) using a modified version of the Rappole and Tipton (1991) figure-8 leg-loop harness. Captive birds fitted with harnesses did not exhibit quantifiable differences in behavior relative to control birds. Based on initial success in using the leg-loop harnesses, we used harnesses to attach transmitters in the wild to 30 Killdeer and 49 Dunlin (Calidris alpina) during the winters of 1998-1999 and 1999-2000. This was part of a study on movements of wintering shorebirds in the Willamette Valley of Oregon, USA. Wild birds showed no adverse effects of the harnesses.Thus, the described harness is a practical method for attachment of transmitters to shorebirds. Advantages of this harness method include a reduction in handling time at capture, elimination of the need to clip feathers for attachment, and increased transmitter retention time.

A Comparison of Blood Metal Ions in Total Hip Arthroplasty Using Metal and Ceramic Heads.

PubMed

White, Peter B; Meftah, Morteza; Ranawat, Amar S; Ranawat, Chitranjan S

2016-10-01

In recent time, metal ion debris and adverse local tissue reaction have reemerged as an area of clinical concern with the use of large femoral heads after total hip arthroplasty (THA). Between June 2014 and January 2015, 60 patients with a noncemented THA using a titanium (titanium, molybdenum, zirconium, and iron alloy) femoral stem and a V40 trunnion were identified with a minimum 5-year follow-up. All THAs had a 32- or 36-mm metal (n = 30) or ceramic (n = 30) femoral head coupled with highly cross-linked polyethylene. Cobalt, chromium, and nickel ions were measured. Patients with metal heads had detectable cobalt and chromium levels. Cobalt levels were detectable in 17 (56.7%) patients with a mean of 2.0 μg/L (range: <1.0-10.8 μg/L). Chromium levels were detectable in 5 (16.7%) patients with a mean of 0.3 μg/L (range: <1.0-2.2 μg/L). All patients with a ceramic head had nondetectable cobalt and chromium levels. Cobalt and chromium levels were significantly higher with metal heads compared to ceramic heads (P < .01). Cobalt levels were significantly higher with 36-mm metal heads compared with 32-mm heads (P < .01). Seven patients with metal femoral heads had mild hip symptoms, 4 of whom had positive findings of early adverse local tissue reaction on magnetic resonance imaging. All ceramic THA was asymptomatic. The incidence and magnitude of cobalt and chromium levels is higher in metal heads compared to ceramic heads with this implant system (P < .01). Thirty-six millimeter metal femoral heads result in larger levels of cobalt compared with 32-mm metal heads. Copyright © 2016 Elsevier Inc. All rights reserved.

[Vascular thrombosis and pulmonary thrombo-embolism due to harness suspension].

PubMed

Pisati, G; Cerri, S; Achille, G; Rossi, G; Lorenzi, G

2007-01-01

In many sports (such as rock-climbing and caving) and working activities (e.g., construction and maintenance of buildings, pruning of lung-trunked trees, abseiling in wells) people run the risk of falling from a height. To prevent the effects of any potential fall, personalprotection devices consisting of at least a body holding device (i.e. a harness of some type), a lanyard and a reliable anchor are used. Reporting on the occurrence of vascular thrombosis in subjects undergoing prolonged hanging in a harness, either for work or recreation. We investigated patients treated for vascular thrombosis in our hospital in the last 5 years to identify subjects with frequent use of a harness. We identified a 36-year-old rock-climber who developed pulmonary thrombo-embolism and infarction 5 days after he had been wearing a harness for 12 hours consecutively, and a 32 year-old worker who often used a harness to fix wire-nettings to prevent rocks falling from steep places and suffered thrombosis of the left superficial femoral artery. A feature of both cases was the considerable length of time spent hanging in the harness and the absence of alternative risk factors for thrombosis. Prolonged hanging in a harness can be dangerous in itself because it can produce vascular thrombosis. Reduction of intravascular blood flow (stasis) and compression of the femoral veins by harness groin straps were the likely pathogenetic mechanisms of the described diseases. The importance is stressed of prevention, which must be based on planned regular breaks in the hanging position, checking on the fit and comfort level of the harness before it is first used, as well as medical surveillance of the subjects who spend prolonged periods in a harness for work or recreation.

77 FR 76840 - Minimum Capital Ratios; Issuance of Directives

Federal Register 2010, 2011, 2012, 2013, 2014

2012-12-31

... Advanced Measurement Approaches * * * * * Part I. General Provisions Section 1. Purpose, Applicability... total on-balance sheet foreign exposure at the most recent year-end equal to $10 billion or more (where total on-balance sheet foreign exposure equals total cross-border claims less claims with head office or...

Head repositioning accuracy in patients with whiplash-associated disorders.

PubMed

Feipel, Veronique; Salvia, Patrick; Klein, Helene; Rooze, Marcel

2006-01-15

Controlled study, measuring head repositioning error (HRE) using an electrogoniometric device. To compare HRE in neutral position, axial rotation and complex postures of patients with whiplash-associated disorders (WAD) to that of control subjects. The presence of kinesthetic alterations in patients with WAD is controversial. In 26 control subjects and 29 patients with WAD (aged 22-74 years), head kinematics was sampled using a 3-dimensional electrogoniometer mounted using a harness and a helmet. All tasks were realized in seated position. The repositioning tasks included neutral repositioning after maximal flexion-extension, eyes open and blindfolded, repositioning at 50 degrees of axial rotation, and repositioning at 50 degrees of axial rotation combined to 20 degrees of ipsilateral bending. The flexion-extension, ipsilateral bending, and axial rotation components of HRE were considered. A multiple-way repeated-measures analysis of variance was used to compare tasks and groups. The WAD group displayed a reduced flexion-extension range (P = 1.9 x 10(-4)), and larger HRE during flexion-extension and repositioning tasks (P = 0.009) than controls. Neither group nor task affected maximal motion velocity. Neutral HRE of the flexion-extension component was larger in blindfolded condition (P = 0.03). Ipsilateral bending and axial rotation HRE components were smaller than the flexion-extension component (P = 7.1 x 10(-23)). For pure rotation repositioning, axial rotation HRE was significantly larger than flexion-extension and ipsilateral bending repositioning error (P = 3.0 x 10(-23)). Ipsilateral bending component of HRE was significantly larger combined tasks than for pure rotation tasks (P = 0.004). In patients with WAD, range of motion and head repositioning accuracy were reduced. However, the differences were small. Vision suppression and task type influenced HRE.

The dynamics of head-on collisions of spherical stellar systems

NASA Astrophysics Data System (ADS)

Narasimhan, K. S. V. S.; Alladin, Saleh Mohammed

1986-12-01

Energy changes in a head-on collision between two unequal Plummer model stellar systems (galaxies) are studied analytically under the impulsive approximation. The variation of the disruptive effects within and the mass escape from systems widely differing in mass and scalelength ratios are determined, and some physical implications regarding the dynamical stability of the systems undergoing head-on collisions are indicated. It is found that if two systems differ considerably in size, both systems generally survive the collision if (1) the mass of the bigger is greater than about six times the mass of the smaller and (2) the density of the smaller is more than about twenty-five times the entity of the bigger system, when the velocity at minimum separation is equal to the parabolic velocity of escape.

78 FR 14442 - Airworthiness Directives; Turbomeca S.A. Turboshaft Engines

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-06

... certain serial number (S/N) N2 sensor harnesses. This AD requires replacement of the same S/N harnesses, and requires replacement of additional S/N N2 sensor harnesses. This AD was prompted by corrosion detected in affected N2 sensor harnesses. We are issuing this AD to prevent inadvertent activation of the...

14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 2 2011-01-01 2011-01-01 false Use of safety belts, shoulder harnesses... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child... fasten and unfasten that person's safety belt and, if installed, shoulder harness. (2) No pilot may cause...

Registration of two double rust resistant germplasms, HA-R12 and HA-R13 for confection sunflower

USDA-ARS?s Scientific Manuscript database

The confection sunflower (Helianthus annuus L.) germplasms HA-R12 (Reg. No. ______, PI 673104) and HA-R13 (Reg. No. ______, PI 673105) were developed by the USDA-ARS, Sunflower and Plant Biology Research Unit in collaboration with the North Dakota Agricultural Experiment Station, and released in Jul...

Hormonal changes in antiorthostatic rats

NASA Technical Reports Server (NTRS)

Popovic, V.; Popovic, P.; Honeycutt, C.

1982-01-01

Hypokinesia, especially hypokinesia with negative tilt ('antiorthostatic hypokinesia'), mimics some of the effects of weightlessness. It is shown that cardiac output is increased during early exposure of rats to antiorthostatic hypokinesia. The increase of the stroke volume and of the cardiac output observed in the antiorthostatic hypokinetic rats is probably the consequence of a blood volume shift toward the chest brought forth by head-down positioning of the animals. It is also possible that struggling of the animals to escape from the harness and an increased metabolism contribute to the elevation of cardiac output. In order to study this hypothesis 'stress hormones' were measured in the antiorthostatic rats. Plasma levels of ACTH, corticosterone and prolactin were measured in the arterial blood (0.3 ml) sampled before, during and after hypokinesia from chronic aortic cannulas of the rats.

VeLoc: Finding Your Car in Indoor Parking Structures.

PubMed

Gao, Ruipeng; He, Fangpu; Li, Teng

2018-05-02

While WiFi-based indoor localization is attractive, there are many indoor places without WiFi coverage with a strong demand for localization capability. This paper describes a system and associated algorithms to address the indoor vehicle localization problem without the installation of additional infrastructure. In this paper, we propose VeLoc, which utilizes the sensor data of smartphones in the vehicle together with the floor map of the parking structure to track the vehicle in real time. VeLoc simultaneously harnesses constraints imposed by the map and environment sensing. All these cues are codified into a novel augmented particle filtering framework to estimate the position of the vehicle. Experimental results show that VeLoc performs well when even the initial position and the initial heading direction of the vehicle are completely unknown.

Reliability of a Parallel Pipe Network

NASA Technical Reports Server (NTRS)

Herrera, Edgar; Chamis, Christopher (Technical Monitor)

2001-01-01

The goal of this NASA-funded research is to advance research and education objectives in theoretical and computational probabilistic structural analysis, reliability, and life prediction methods for improved aerospace and aircraft propulsion system components. Reliability methods are used to quantify response uncertainties due to inherent uncertainties in design variables. In this report, several reliability methods are applied to a parallel pipe network. The observed responses are the head delivered by a main pump and the head values of two parallel lines at certain flow rates. The probability that the flow rates in the lines will be less than their specified minimums will be discussed.

A kinetic comparison of back-loading and head-loading in Xhosa women.

PubMed

Lloyd, R; Parr, B; Davies, S; Cooke, C

2011-04-01

The purpose of this study was to compare the kinetic responses associated with ground reaction force measurements to both head-loading and back-loading in a group of Xhosa women. Altogether, 16 women were divided into two groups based on their experience of head-loading. They walked over a force plate in three conditions: unloaded or carrying 20 kg in either a backpack or on their head. The most striking finding was that there was no difference in kinetic response to head-loading as a consequence of previous experience. Considering the differences between the load carriage methods, most changes were consistent with increasing load. Head-loading was, however, associated with a shorter contact time, smaller thrust maximum and greater vertical force minimum than back-loading. Both loading conditions differed from unloaded walking for a number of temporal variables associated with the ground contact phase, e.g. vertical impact peak was delayed whilst vertical thrust maximum occurred earlier. STATEMENT OF RELEVANCE: Consideration of the kinetics of head and back load carriage in African women is important from a health and safety perspective, providing an understanding of the mechanical adaptations associated with both forms of load carriage for a group of people for whom such load carriage is a daily necessity.

[Concordance between a head circumference growth function and intellectual disability in relation with the cause of microcephaly].

PubMed

Coronado, R; Macaya Ruíz, A; Giraldo Arjonilla, J; Roig-Quilis, M

2015-08-01

Our aim was to investigate the correlations between patterns of head growth and intellectual disability among distinct aetiological presentations of microcephaly. 3,269 head circumference (HC) charts of patients from a tertiary neuropediatric unit were reviewed and 136 microcephalic participants selected. Using the Z-scores of registered HC measurements we defined the variables: HC Minimum, HC Drop and HC Catch-up. We classified patients according to the presence or absence of intellectual disability (IQ below 71) and according to the cause of microcephaly (idiopathic, familial, syndromic, symptomatic and mixed). Using Discriminant Analysis a C-function was defined as C=HC Minimum + HC Drop with a cut-off level of C=-4.32 Z-score. In our sample 95% of patients scoring below this level, severe microcephaly, were classified in the disabled group while the overall concordance was 66%. In the symptomatic-mixed group the concordance between HC function and outcome reached 82% in contrast to only 54% in the idiopathic-syndromic group (P-value=0.0002). We defined a HC growth function which discriminates intellectual disability of microcephalic patients better than isolated HC measurements, especially for those with secondary and mixed aetiologies. Copyright © 2014 Asociación Española de Pediatría. Published by Elsevier España, S.L.U. All rights reserved.

Experimental procedure for measuring and comparing head-neck-trunk posture and movements caused by different progressive addition lens designs.

PubMed

Mateo, B; Porcar-Seder, R; Solaz, J S; Dürsteler, J C

2010-07-01

This study demonstrates that appropriate measurement procedures can detect differences in head movement in a near reading task when using three different progressive addition lenses (PALs). The movements were measured using an anatomical reference system with a biomechanical rationale. This reference system was capable of representing rotations for comparing head flexion relative to trunk, head flexion relative to neck, head rotation relative to trunk and trunk flexion. The subject sample comprised 31 volunteers and three PAL designs with different viewing zones were selected. Significant differences were found between the lenses for three of the seven movement parameters examined. The differences occurred for both vertical and horizontal head movements and could be attributed to aspects of the PAL design. The measurement of the complete kinematic trunk-neck-head chain improved the number of differences that were found over those in previous studies. STATEMENT OF RELEVANCE: The study proposes a methodology based on a biomechanical rationale able to differentiate head-neck-trunk posture and movements caused by different progressive addition lens designs with minimum invasiveness. This methodology could also be applied to analyse the ergonomics of other devices that restrict the user's field of view, such as helmets, personal protective equipment or helmet-mounted displays for pilots. This analysis will allow designers to optimise designs offering higher comfort and performance.

Neonatal head and torso vibration exposure during inter-hospital transfer

PubMed Central

Blaxter, Laurence; Yeo, Mildrid; McNally, Donal; Crowe, John; Henry, Caroline; Hill, Sarah; Mansfield, Neil; Leslie, Andrew; Sharkey, Don

2017-01-01

Inter-hospital transport of premature infants is increasingly common, given the centralisation of neonatal intensive care. However, it is known to be associated with anomalously increased morbidity, most notably brain injury, and with increased mortality from multifactorial causes. Surprisingly, there have been relatively few previous studies investigating the levels of mechanical shock and vibration hazard present during this vehicular transport pathway. Using a custom inertial datalogger, and analysis software, we quantify vibration and linear head acceleration. Mounting multiple inertial sensing units on the forehead and torso of neonatal patients and a preterm manikin, and on the chassis of transport incubators over the duration of inter-site transfers, we find that the resonant frequency of the mattress and harness system currently used to secure neonates inside incubators is ~9Hz. This couples to vehicle chassis vibration, increasing vibration exposure to the neonate. The vibration exposure per journey (A(8) using the ISO 2631 standard) was at least 20% of the action point value of current European Union regulations over all 12 neonatal transports studied, reaching 70% in two cases. Direct injury risk from linear head acceleration (HIC15) was negligible. Although the overall hazard was similar, vibration isolation differed substantially between sponge and air mattresses, with a manikin. Using a Global Positioning System datalogger alongside inertial sensors, vibration increased with vehicle speed only above 60 km/h. These preliminary findings suggest there is scope to engineer better systems for transferring sick infants, thus potentially improving their outcomes. PMID:28056712

Neonatal head and torso vibration exposure during inter-hospital transfer.

PubMed

Blaxter, Laurence; Yeo, Mildrid; McNally, Donal; Crowe, John; Henry, Caroline; Hill, Sarah; Mansfield, Neil; Leslie, Andrew; Sharkey, Don

2017-02-01

Inter-hospital transport of premature infants is increasingly common, given the centralisation of neonatal intensive care. However, it is known to be associated with anomalously increased morbidity, most notably brain injury, and with increased mortality from multifactorial causes. Surprisingly, there have been relatively few previous studies investigating the levels of mechanical shock and vibration hazard present during this vehicular transport pathway. Using a custom inertial datalogger, and analysis software, we quantify vibration and linear head acceleration. Mounting multiple inertial sensing units on the forehead and torso of neonatal patients and a preterm manikin, and on the chassis of transport incubators over the duration of inter-site transfers, we find that the resonant frequency of the mattress and harness system currently used to secure neonates inside incubators is [Formula: see text]. This couples to vehicle chassis vibration, increasing vibration exposure to the neonate. The vibration exposure per journey (A(8) using the ISO 2631 standard) was at least 20% of the action point value of current European Union regulations over all 12 neonatal transports studied, reaching 70% in two cases. Direct injury risk from linear head acceleration (HIC 15 ) was negligible. Although the overall hazard was similar, vibration isolation differed substantially between sponge and air mattresses, with a manikin. Using a Global Positioning System datalogger alongside inertial sensors, vibration increased with vehicle speed only above 60 km/h. These preliminary findings suggest there is scope to engineer better systems for transferring sick infants, thus potentially improving their outcomes.

Registration of two confection sunflower germplasm Lines, HA-R10 and HA-R11, Resistant to sunflower rust

USDA-ARS?s Scientific Manuscript database

Two confection sunflower (Helianthus annuus L.) germplasm lines, HA-R10 (Reg. No.xxx, PI670043) and HA-R11 (Reg. No.xxx, PI670044) were developed by the USDA-ARS Sunflower and Plant Biology Research Unit in collaboration with the North Dakota Agricultural Experiment Station and released December, 20...

JWST ISIM Harness Thermal Evaluation

NASA Technical Reports Server (NTRS)

Kobel, Mark; Glazer, Stuart; Tuttle, Jim; Martins, Mario; Ruppel, Sean

2008-01-01

The James Webb Space Telescope (JWST) will be a large infrared telescope with a 6.5-meter primary mirror. Launch is planned for 2013. JWST wl1 be the premier observatory of the next decade serving thousands of astronomers worldwide. The Integrated Science Instrument Module (ISIM) is the unit that will house thc four main JWST instruments. The ISIM enclosure passively cooled to 37 Kelvin and has a tightly managed thermal budget. A significant portion of the ISIM heat load is due to parasitic heat gains from the instrument harnesses. These harnesses provide a thermal path from the Instrument Electronics Control (IEC) to the ISIM. Because of the impact of this load to the ISIM thermal design, understanding the harness parasitic heat gains is critical. To this effect, a thermal test program has been conducted in order to characterize these parasitic loads and verify harness thermal models. Recent parasitic heat loads tests resulted in the addition of a dedicated multiple stage harness radiator. In order for the radiator to efficiently reject heat from the harness, effective thermal contact conductance values for multiple harnesses had to be determined. This presentation will describe the details and the results of this test program.

Levels of detail analysis of microwave scattering from human head models for brain stroke detection

PubMed Central

2017-01-01

In this paper, we have presented a microwave scattering analysis from multiple human head models. This study incorporates different levels of detail in the human head models and its effect on microwave scattering phenomenon. Two levels of detail are taken into account; (i) Simplified ellipse shaped head model (ii) Anatomically realistic head model, implemented using 2-D geometry. In addition, heterogenic and frequency-dispersive behavior of the brain tissues has also been incorporated in our head models. It is identified during this study that the microwave scattering phenomenon changes significantly once the complexity of head model is increased by incorporating more details using magnetic resonance imaging database. It is also found out that the microwave scattering results match in both types of head model (i.e., geometrically simple and anatomically realistic), once the measurements are made in the structurally simplified regions. However, the results diverge considerably in the complex areas of brain due to the arbitrary shape interface of tissue layers in the anatomically realistic head model. After incorporating various levels of detail, the solution of subject microwave scattering problem and the measurement of transmitted and backscattered signals were obtained using finite element method. Mesh convergence analysis was also performed to achieve error free results with a minimum number of mesh elements and a lesser degree of freedom in the fast computational time. The results were promising and the E-Field values converged for both simple and complex geometrical models. However, the E-Field difference between both types of head model at the same reference point differentiated a lot in terms of magnitude. At complex location, a high difference value of 0.04236 V/m was measured compared to the simple location, where it turned out to be 0.00197 V/m. This study also contributes to provide a comparison analysis between the direct and iterative solvers so as to find out the solution of subject microwave scattering problem in a minimum computational time along with memory resources requirement. It is seen from this study that the microwave imaging may effectively be utilized for the detection, localization and differentiation of different types of brain stroke. The simulation results verified that the microwave imaging can be efficiently exploited to study the significant contrast between electric field values of the normal and abnormal brain tissues for the investigation of brain anomalies. In the end, a specific absorption rate analysis was carried out to compare the ionizing effects of microwave signals to different types of head model using a factor of safety for brain tissues. It is also suggested after careful study of various inversion methods in practice for microwave head imaging, that the contrast source inversion method may be more suitable and computationally efficient for such problems. PMID:29177115

Positioning bars for large wire harnesses

NASA Technical Reports Server (NTRS)

Glessner, J. R.

1978-01-01

By tying positioning bars to harness, its configuration can be preserved during transport, thus facilitating installation. Harness can also be showed temporarily by placing hanging hooks on end of bar.

"Far" and "Near" Visual Acuity While Walking and the Collective Contributions of Non-Ocular Mechanisms to Gaze Stabilization

NASA Technical Reports Server (NTRS)

Peters, Brian T.; vanEmmerik, Richard E. A.; Bloomberg, Jacob J.

2006-01-01

Gaze stabilization was quantified in subjects (n=11) as they walked on a motorized treadmill (1.8 m/s) and viewed visual targets at two viewing distances. A "far" target was positioned at 4 m (FAR) in front of the subject and the "near" target was placed at a distance of 0.5 m (NEAR). A direct measure of visual acuity was used to assess the overall effectiveness of the gaze stabilization system. The contributions of nonocular mechanisms to the gaze goal were also quantified using a measure of the distance between the subject and point in space where fixation of the visual target would require the least eye movement amplitude (i.e. the head fixation distance (HFD)). Kinematic variables mirrored those of previous investigations with the vertical trunk translation and head pitch signals, and the lateral translation and head yaw signals maintaining what appear as antiphase relationships. However, an investigation of the temporal relationships between the maxima and minima of the vertical translation and head pitch signals show that while the maximum in vertical translation occurs at the point of the minimum head pitch signal, the inverse is not true. The maximum in the head pitch signal lags the vertical translation minimum by an average of greater than 12 percent of the step cycle time. Three HFD measures, one each for data in the sagittal and transverse planes, and one that combined the movements from both planes, all revealed changes between the FAR and NEAR target viewing conditions. This reorganization of the nonocular degrees of freedom while walking was consistent with a strategy to reduce the magnitude of the eye movements required when viewing the NEAR target. Despite this reorganization, acuity measures show that image stabilization is not occurring while walking and viewing the NEAR target. Group means indicate that visual acuity is not affected while walking in the FAR condition, but a decrement of 0.15 logMAR (i.e. 1.5 eye chart lines) exists between the standing and walking acuity measures when viewing the NEAR target.

Kinematic principles of primate rotational vestibulo-ocular reflex. I. Spatial organization of fast phase velocity axes

NASA Technical Reports Server (NTRS)

Hess, B. J.; Angelaki, D. E.

1997-01-01

The spatial organization of fast phase velocity vectors of the vestibulo-ocular reflex (VOR) was studied in rhesus monkeys during yaw rotations about an earth-horizontal axis that changed continuously the orientation of the head relative to gravity ("barbecue spit" rotation). In addition to a velocity component parallel to the rotation axis, fast phases also exhibited a velocity component that invariably was oriented along the momentary direction of gravity. As the head rotated through supine and prone positions, torsional components of fast phase velocity axes became prominent. Similarly, as the head rotated through left and right ear-down positions, fast phase velocity axes exhibited prominent vertical components. The larger the speed of head rotation the greater the magnitude of this fast phase component, which was collinear with gravity. The main sequence properties of VOR fast phases were independent of head position. However, peak amplitude as well as peak velocity of fast phases were both modulated as a function of head orientation, exhibiting a minimum in prone position. The results suggest that the fast phases of vestibulo-ocular reflexes not only redirect gaze and reposition the eye in the direction of head motion but also reorient the eye with respect to earth-vertical when the head moves relative to gravity. As further elaborated in the companion paper, the underlying mechanism could be described as a dynamic, gravity-dependent modulation of the coordinates of ocular rotations relative to the head.

New head exposure system for use in human provocation studies with EEG recording during GSM900- and UMTS-like exposure.

PubMed

Schmid, Gernot; Cecil, Stefan; Goger, Christoph; Trimmel, Michael; Kuster, Niels; Molla-Djafari, Hamid

2007-12-01

A new head exposure system for double blinded human provocation studies, which requires EEG recording during exposure with GSM900- and UMTS-like signals has been developed and dosimetrically evaluated. The system uses planar patch antennas fixed at 65 mm distance from the subject's head by a special headset, which provides minimum impairment of the test subjects and ensures an almost constant position of the antennas with respect to the head, even in case of head movements. Compared to exposure concepts operating small antennas in close proximity to the head, the concept of planar antennas at a certain distance from the head produces a much more homogeneous SAR distribution in the temporal and parietal lobe of the brain. At the same time the resulting uncertainty of exposure due to variations in head size, variations of the dielectric properties of tissues and unavoidable small changes of the antenna's position with respect to the head, is reduced to the order of approximately 3 dB, which is a significant improvement to comparable head exposure systems reported in literature in the past. To avoid electromagnetic interference on the EEG recording caused by the incident RF-field an appropriate double-shielded filter circuit has been developed. Furthermore, the effect of the presence of the sintered Ag/AgCl EEG electrodes and electrode wires on the SAR distribution inside the head has been investigated and was found to be minimal if the electrode wires are arranged orthogonal to the incident electric field vector. EEG electrode arrangement parallel to the incident field vector, however, might cause drastic changes in the SAR distribution inside the head. (c) 2007 Wiley-Liss, Inc.

40 CFR 1065.510 - Engine mapping.

Code of Federal Regulations, 2011 CFR

2011-07-01

... the warm-up until the engine coolant, block, or head absolute temperature is within ± 2% of its mean... demand to minimum, use the dynamometer or other loading device to target a torque of zero on the engine's...-speed governor, operate the engine at warm idle speed and zero torque on the engine's primary output...

Genomic and Network Patterns of Schizophrenia Genetic Variation in Human Evolutionary Accelerated Regions

PubMed Central

Xu, Ke; Schadt, Eric E.; Pollard, Katherine S.; Roussos, Panos; Dudley, Joel T.

2015-01-01

The population persistence of schizophrenia despite associated reductions in fitness and fecundity suggests that the genetic basis of schizophrenia has a complex evolutionary history. A recent meta-analysis of schizophrenia genome-wide association studies offers novel opportunities for assessment of the evolutionary trajectories of schizophrenia-associated loci. In this study, we hypothesize that components of the genetic architecture of schizophrenia are attributable to human lineage-specific evolution. Our results suggest that schizophrenia-associated loci enrich in genes near previously identified human accelerated regions (HARs). Specifically, we find that genes near HARs conserved in nonhuman primates (pHARs) are enriched for schizophrenia-associated loci, and that pHAR-associated schizophrenia genes are under stronger selective pressure than other schizophrenia genes and other pHAR-associated genes. We further evaluate pHAR-associated schizophrenia genes in regulatory network contexts to investigate associated molecular functions and mechanisms. We find that pHAR-associated schizophrenia genes significantly enrich in a GABA-related coexpression module that was previously found to be differentially regulated in schizophrenia affected individuals versus healthy controls. In another two independent networks constructed from gene expression profiles from prefrontal cortex samples, we find that pHAR-associated schizophrenia genes are located in more central positions and their average path lengths to the other nodes are significantly shorter than those of other schizophrenia genes. Together, our results suggest that HARs are associated with potentially important functional roles in the genetic architecture of schizophrenia. PMID:25681384

Are we ignoring neutral and negative human-animal relationships in zoos?

PubMed

Hosey, Geoff; Melfi, Vicky

2015-01-01

Human-animal interactions (HAI), which may lead to human-animal relationships (HAR), may be positive, neutral, or negative in nature. Zoo studies show that visitors may be stressful, may have no effect, or may be enriching. There is also evidence that good HARs set up between animals and their keepers can have positive effects on animal welfare. However, we need to know more about negative HARs, and as a first step we attempt to do this here by considering cases where animals attack people in the zoo. Due to the sensitivity and rarity of these events data appear sparse and unsystematically collected. Here, information available in the public domain about the circumstances of these attacks has been collated to test hypotheses about negative HAIs derived from a model of zoo HARs. The limited data presented here broadly support the zoo HAR model, and suggest that attacks usually happen in unusual circumstances, where there may be a failure by the animal to recognise the HAR, or where the relationship, if there is one, does not hold; and give some support to the prediction that exposure to many keepers may impair the development of a positive HAR. This study may provide useful information for the zoo community to proactively collect systematic standardised records, which will enable a fuller understanding of zoo HARs, upon which appropriate measures might be adopted to build better zoo HARs, which are likely to positively impact zoo animal welfare, and reduce these rare incidences further. © 2014 Wiley Periodicals, Inc.

Virginia Department of Transportation HAR Operational Guidelines

DOT National Transportation Integrated Search

1995-08-01

These guidelines have been developed to help Virginia Department of Transportation (VDOT) personnel effectively operate highway advisory radio (HAR) systems. Operators should continually bear in mind that it is of paramount importance that HAR messag...

Minimum-norm cortical source estimation in layered head models is robust against skull conductivity error☆☆☆

PubMed Central

Stenroos, Matti; Hauk, Olaf

2013-01-01

The conductivity profile of the head has a major effect on EEG signals, but unfortunately the conductivity for the most important compartment, skull, is only poorly known. In dipole modeling studies, errors in modeled skull conductivity have been considered to have a detrimental effect on EEG source estimation. However, as dipole models are very restrictive, those results cannot be generalized to other source estimation methods. In this work, we studied the sensitivity of EEG and combined MEG + EEG source estimation to errors in skull conductivity using a distributed source model and minimum-norm (MN) estimation. We used a MEG/EEG modeling set-up that reflected state-of-the-art practices of experimental research. Cortical surfaces were segmented and realistically-shaped three-layer anatomical head models were constructed, and forward models were built with Galerkin boundary element method while varying the skull conductivity. Lead-field topographies and MN spatial filter vectors were compared across conductivities, and the localization and spatial spread of the MN estimators were assessed using intuitive resolution metrics. The results showed that the MN estimator is robust against errors in skull conductivity: the conductivity had a moderate effect on amplitudes of lead fields and spatial filter vectors, but the effect on corresponding morphologies was small. The localization performance of the EEG or combined MEG + EEG MN estimator was only minimally affected by the conductivity error, while the spread of the estimate varied slightly. Thus, the uncertainty with respect to skull conductivity should not prevent researchers from applying minimum norm estimation to EEG or combined MEG + EEG data. Comparing our results to those obtained earlier with dipole models shows that general judgment on the performance of an imaging modality should not be based on analysis with one source estimation method only. PMID:23639259

Virtual local target method for avoiding local minimum in potential field based robot navigation.

PubMed

Zou, Xi-Yong; Zhu, Jing

2003-01-01

A novel robot navigation algorithm with global path generation capability is presented. Local minimum is a most intractable but is an encountered frequently problem in potential field based robot navigation. Through appointing appropriately some virtual local targets on the journey, it can be solved effectively. The key concept employed in this algorithm are the rules that govern when and how to appoint these virtual local targets. When the robot finds itself in danger of local minimum, a virtual local target is appointed to replace the global goal temporarily according to the rules. After the virtual target is reached, the robot continues on its journey by heading towards the global goal. The algorithm prevents the robot from running into local minima anymore. Simulation results showed that it is very effective in complex obstacle environments.

Harnessing Scientific Literature Reports for Pharmacovigilance

PubMed Central

Ripple, Anna; Tonning, Joseph; Munoz, Monica; Hasan, Rashedul; Ly, Thomas; Francis, Henry; Bodenreider, Olivier

2017-01-01

Summary Objectives We seek to develop a prototype software analytical tool to augment FDA regulatory reviewers’ capacity to harness scientific literature reports in PubMed/MEDLINE for pharmacovigilance and adverse drug event (ADE) safety signal detection. We also aim to gather feedback through usability testing to assess design, performance, and user satisfaction with the tool. Methods A prototype, open source, web-based, software analytical tool generated statistical disproportionality data mining signal scores and dynamic visual analytics for ADE safety signal detection and management. We leveraged Medical Subject Heading (MeSH) indexing terms assigned to published citations in PubMed/MEDLINE to generate candidate drug-adverse event pairs for quantitative data mining. Six FDA regulatory reviewers participated in usability testing by employing the tool as part of their ongoing real-life pharmacovigilance activities to provide subjective feedback on its practical impact, added value, and fitness for use. Results All usability test participants cited the tool’s ease of learning, ease of use, and generation of quantitative ADE safety signals, some of which corresponded to known established adverse drug reactions. Potential concerns included the comparability of the tool’s automated literature search relative to a manual ‘all fields’ PubMed search, missing drugs and adverse event terms, interpretation of signal scores, and integration with existing computer-based analytical tools. Conclusions Usability testing demonstrated that this novel tool can automate the detection of ADE safety signals from published literature reports. Various mitigation strategies are described to foster improvements in design, productivity, and end user satisfaction. PMID:28326432

Harnessing scientific literature reports for pharmacovigilance. Prototype software analytical tool development and usability testing.

PubMed

Sorbello, Alfred; Ripple, Anna; Tonning, Joseph; Munoz, Monica; Hasan, Rashedul; Ly, Thomas; Francis, Henry; Bodenreider, Olivier

2017-03-22

We seek to develop a prototype software analytical tool to augment FDA regulatory reviewers' capacity to harness scientific literature reports in PubMed/MEDLINE for pharmacovigilance and adverse drug event (ADE) safety signal detection. We also aim to gather feedback through usability testing to assess design, performance, and user satisfaction with the tool. A prototype, open source, web-based, software analytical tool generated statistical disproportionality data mining signal scores and dynamic visual analytics for ADE safety signal detection and management. We leveraged Medical Subject Heading (MeSH) indexing terms assigned to published citations in PubMed/MEDLINE to generate candidate drug-adverse event pairs for quantitative data mining. Six FDA regulatory reviewers participated in usability testing by employing the tool as part of their ongoing real-life pharmacovigilance activities to provide subjective feedback on its practical impact, added value, and fitness for use. All usability test participants cited the tool's ease of learning, ease of use, and generation of quantitative ADE safety signals, some of which corresponded to known established adverse drug reactions. Potential concerns included the comparability of the tool's automated literature search relative to a manual 'all fields' PubMed search, missing drugs and adverse event terms, interpretation of signal scores, and integration with existing computer-based analytical tools. Usability testing demonstrated that this novel tool can automate the detection of ADE safety signals from published literature reports. Various mitigation strategies are described to foster improvements in design, productivity, and end user satisfaction.

Region IV Transit Workshop: Harnessing the Private Sector

DOT National Transportation Integrated Search

1988-09-01

This Report constitutes the Proceedings of the Region IV Transit Workshop: : Harnessing the Private Sector. Included in this document is a general report of : the activities of the Workshop. : The purpose ot the Region IV Transit Workshop: Harnessing...

[Binding interaction of harpagoside and bovine serum albumin: spectroscopic methodologies and molecular docking].

PubMed

Cao, Tuan-Wu; Huang, Wen-Bing; Shi, Jian-Wei; He, Wei

2018-03-01

Scrophularia ningpoensis has exhibited a variety of biological activities and been used as a pharmaceutical product for the treatment of inflammatory ailment, rheumatoid arthritis, osteoarthritis and so on. Harpagoside (HAR) is considerer as a main bioactive compound in this plant. Serum albumin has important physiological roles in transportation, distribution and metabolism of many endogenous and exogenous substances in body. It is of great significance to study the interaction mechanism between HAR and bovine serum albumin (BSA). The mechanism of interaction between HAR and BSA was investigated using 2D and 3D fluorescence, synchronous florescence, ultraviolet spectroscopy and molecular docking. According to the analysis of fluorescence spectra, HAR could strongly quench the fluorescence of BSA, and the static quenching process indicated that the decrease in the quenching constant was observed with the increase in temperature. The magnitude of binding constants (KA) was more than 1×10⁵ L·mol⁻¹, and the number of binding sites(n) was approximate to 1. The thermodynamic parameters were calculated through analysis of fluorescence data with Stern-Volmer and Van't Hoff equation. The calculated enthalpy change (ΔH) and entropy change (ΔS) implied that the main interaction forces of HAR with BSA were the bonding interaction between van der Waals forces and hydrogen. The negative values of energy (ΔG) demonstrated that the binding of HAR with BSA was a spontaneous and exothermic process. The binding distance(r) between HAR and BSA was calculated to be about 2.80 nm based on the theory of Frster's non-radiation energy transfer, which indicated that energy is likely to be transfer from BSA to HAR. Both synchronous and 3D florescence spectroscopy clearly revealed that the microenvironment and conformation of BSA changed during the binding interaction between HAR and BSA. The molecular docking analysis revealed HAR is more inclined to BSA and human serum albumin (HSA) in subdomain ⅡA (Sudlow's site I). This study will provide valuable information for understanding the action mechanism of HAR. Copyright© by the Chinese Pharmaceutical Association.

MSFC inspections of installed polyimide wire

NASA Technical Reports Server (NTRS)

Landers, Joe C.

1994-01-01

An alert was issued because of the arc-tracking possibilities of installed polyimide wire harnesses. MSFC undertook a program to try to enhance the safety and reliability of these harnesses. Photographs are presented showing the need for inspections of installed wiring harnesses.

Impact of Harness Attachment Point on Kinetics and Kinematics During Sled Towing.

PubMed

Bentley, Ian; Atkins, Steve J; Edmundson, Christopher J; Metcalfe, John; Sinclair, Jonathan K

2016-03-01

Resisted sprint training is performed in a horizontal direction and involves similar muscles, velocities, and ranges of motion (ROM) to those of normal sprinting. Generally, sleds are attached to the athletes through a lead (3 m) and harness; the most common attachment points are the shoulder or waist. At present, it is not known how the different harness point's impact on the kinematics and kinetics associated with sled towing (ST). The aim of the current investigation was to examine the kinetics and kinematics of shoulder and waist harness attachment points in relation to the acceleration phase of ST. Fourteen trained men completed normal and ST trials, loaded at 10% reduction of sprint velocity. Sagittal plane kinematics from the trunk, hip, knee, and ankle were measured, together with stance phase kinetics (third footstrike). Kinetic and kinematic parameters were compared between harness attachments using one-way repeated-measures analysis of variance. The results indicated that various kinetic differences were present between the normal and ST conditions. Significantly greater net horizontal mean force, net horizontal impulses, propulsive mean force, and propulsive impulses were measured (p < 0.05). Interestingly, the waist harness also led to greater net horizontal impulse when compared with the shoulder attachment (p < 0.001). In kinematic terms, ST conditions significantly increased peak flexion in hip, knee, and ankle joints compared with the normal trials (p < 0.05). Results highlighted that the shoulder harness had a greater impact on trunk and knee joint kinematics when compared with the waist harness (p < 0.05). In summary, waist harnesses seem to be the most suitable attachment point for the acceleration phase of sprinting. Sled towing with these attachments resulted in fewer kinematic alterations and greater net horizontal impulse when compared with the shoulder harness. Future research is necessary in order to explore the long-term adaptations of these acute changes.

Effects of firefighters' self-contained breathing apparatus' weight and its harness design on the physiological and subjective responses.

PubMed

Bakri, Ilham; Lee, Joo-Young; Nakao, Kouhei; Wakabayashi, Hitoshi; Tochihara, Yutaka

2012-01-01

To examine the effects of firefighters' self-contained breathing apparatus' (SCBA) weight and its harness design on the physiological and subjective responses, eight male students performed treadmill exercise under four conditions: the 8 kg firefighter protective clothing (PC) (Control), the PC + an 11 kg SCBA with an old harness (Test A), the PC + a 6.4 kg SCBA with an old harness (Test B) and the PC + a 6.4 kg SCBA with a new harness (Test C), at ambient temperatures (T(a)) of 22°C and 32°C. Besides highlighting the fact that a heavy SCBA had a significant effect on the oxygen consumption and metabolic rate, this experiment also found that in a T(a) of 32°C, in particular, the combined effect of 4.7 kg lighter SCBA and new harness design could reduce metabolic rate and improved subjective muscle fatigue and thermal discomfort. An effort to alleviate the physiological and subjective burden of firefighters by reducing the weight of SCBA and by using the new harness design has provided satisfactory results in reduced oxygen consumption and in improved subjective responses in a hot air environment.

The benefits of the use of shoulder harness in general aviation aircraft.

DOT National Transportation Integrated Search

1972-02-01

The installation and use of shoulder harnesses is a practical and relatively inexpensive solution to the problem of maintaining separation between man and machine during an aircraft crash sequence. The addition of shoulder harness to the tiedown chai...

Spring control of wire harness loops

NASA Technical Reports Server (NTRS)

Curcio, P. J.

1979-01-01

Negator spring control guides wire harness between movable and fixed structure. It prevents electrical wire harness loop from jamming or being severed as wire moves in response to changes in position of aircraft rudder. Spring-loaded coiled cable controls wire loop regardless of rudder movement.

SSME Electrical Harness and Cable Development and Evolution

NASA Technical Reports Server (NTRS)

Abrams, Russ; Heflin, Johnny; Burns, Bob; Camper, Scott J.; Hill, Arthur J.

2010-01-01

The Space Shuttle Main Engine (SSME) electrical harness and cable system consists of the various interconnecting devices necessary for operation of complex rocket engine functions. Thirty seven harnesses incorporate unique connectors, backshell adapters, conductors, insulation, shielding, and physical barriers for a long maintenance-free life while providing the means to satisfy performance requirements and to mitigate adverse environmental influences. The objective of this paper is to provide a description of the SSME electrical harness and cable designs as well as the development history and lessons learned.

Damping Models for Shear-Deformable Beam with Applications to Spacecraft Wiring Harness

DTIC Science & Technology

2014-10-28

AFRL-RV-PS- TR-2014-0189 AFRL-RV-PS- TR-2014-0189 DAMPING MODELS FOR SHEAR-DEFORMABLE BEAM WITH APPLICATIONS TO SPACECRAFT WIRING HARNESS ...Feb 2012 4. TITLE AND SUBTITLE Damping Models for Shear-Deformable Beam with Applications to Spacecraft Wiring Harness 5a. CONTRACT NUMBER FA9453-12...behavior of wiring harnesses . The emphasis in this project will be on the extension of the shear-beam damping model to the Timoshenko beam, a beam model

Heritability and factors associated with number of harness race starts in the Spanish Trotter horse population.

PubMed

Solé, M; Valera, M; Gómez, M D; Sölkner, J; Molina, A; Mészáros, G

2017-05-01

Longevity/durability is a relevant trait in racehorses. Genetic analysis and knowledge of factors that influence number of harness race starts would be advantageous for both horse welfare and the equine industry. To perform a genetic analysis on harness racing using number of races as a measure of longevity/durability and to identify factors associated with career length in Spanish Trotter Horses (STH). Longitudinal study. Performance data (n = 331,970) on the STH population for harness racing at national level between 1990 and 2014 were used. A grouped data model was fitted to assess factors influencing the risk of ending harness racing career and to estimate the heritability and breeding values for total number of harness races starts as an indicator of horses' longevity and durability. The model included sex, age at first race and first start earnings as time-independent effects, and the calendar year, driver, trainer, racetrack category and season of competition as time-dependent effects. Across the whole dataset, the average number of harness races horses achieved in Spain was 54.7 races, and this was associated with the horses' sex, age at first race and first start earnings, calendar year, driver, racetrack category, and season. The heritability estimated (0.17 ± 0.01) for number of harness race starts indicates that a beneficial response to direct genetic selection can be expected. Data on horses' health status were not available. Horses' total number of harness race starts is a promising tool for genetic analysis and the evaluation of racing longevity and durability. The estimated heritability provides evidence to support the application of genetic selection of total career number of races to improve longevity/durability of STH. © 2016 EVJ Ltd.

The EADC-ADNI Harmonized Protocol for manual hippocampal segmentation on magnetic resonance: evidence of validity.

PubMed

Frisoni, Giovanni B; Jack, Clifford R; Bocchetta, Martina; Bauer, Corinna; Frederiksen, Kristian S; Liu, Yawu; Preboske, Gregory; Swihart, Tim; Blair, Melanie; Cavedo, Enrica; Grothe, Michel J; Lanfredi, Mariangela; Martinez, Oliver; Nishikawa, Masami; Portegies, Marileen; Stoub, Travis; Ward, Chadwich; Apostolova, Liana G; Ganzola, Rossana; Wolf, Dominik; Barkhof, Frederik; Bartzokis, George; DeCarli, Charles; Csernansky, John G; deToledo-Morrell, Leyla; Geerlings, Mirjam I; Kaye, Jeffrey; Killiany, Ronald J; Lehéricy, Stephane; Matsuda, Hiroshi; O'Brien, John; Silbert, Lisa C; Scheltens, Philip; Soininen, Hilkka; Teipel, Stefan; Waldemar, Gunhild; Fellgiebel, Andreas; Barnes, Josephine; Firbank, Michael; Gerritsen, Lotte; Henneman, Wouter; Malykhin, Nikolai; Pruessner, Jens C; Wang, Lei; Watson, Craig; Wolf, Henrike; deLeon, Mony; Pantel, Johannes; Ferrari, Clarissa; Bosco, Paolo; Pasqualetti, Patrizio; Duchesne, Simon; Duvernoy, Henri; Boccardi, Marina

2015-02-01

An international Delphi panel has defined a harmonized protocol (HarP) for the manual segmentation of the hippocampus on MR. The aim of this study is to study the concurrent validity of the HarP toward local protocols, and its major sources of variance. Fourteen tracers segmented 10 Alzheimer's Disease Neuroimaging Initiative (ADNI) cases scanned at 1.5 T and 3T following local protocols, qualified for segmentation based on the HarP through a standard web-platform and resegmented following the HarP. The five most accurate tracers followed the HarP to segment 15 ADNI cases acquired at three time points on both 1.5 T and 3T. The agreement among tracers was relatively low with the local protocols (absolute left/right ICC 0.44/0.43) and much higher with the HarP (absolute left/right ICC 0.88/0.89). On the larger set of 15 cases, the HarP agreement within (left/right ICC range: 0.94/0.95 to 0.99/0.99) and among tracers (left/right ICC range: 0.89/0.90) was very high. The volume variance due to different tracers was 0.9% of the total, comparing favorably to variance due to scanner manufacturer (1.2), atrophy rates (3.5), hemispheric asymmetry (3.7), field strength (4.4), and significantly smaller than the variance due to atrophy (33.5%, P < .001), and physiological variability (49.2%, P < .001). The HarP has high measurement stability compared with local segmentation protocols, and good reproducibility within and among human tracers. Hippocampi segmented with the HarP can be used as a reference for the qualification of human tracers and automated segmentation algorithms. Copyright © 2015 The Alzheimer's Association. Published by Elsevier Inc. All rights reserved.

The EADC-ADNI Harmonized Protocol for manual hippocampal segmentation on magnetic resonance: Evidence of validity

PubMed Central

Frisoni, Giovanni B.; Jack, Clifford R.; Bocchetta, Martina; Bauer, Corinna; Frederiksen, Kristian S.; Liu, Yawu; Preboske, Gregory; Swihart, Tim; Blair, Melanie; Cavedo, Enrica; Grothe, Michel J.; Lanfredi, Mariangela; Martinez, Oliver; Nishikawa, Masami; Portegies, Marileen; Stoub, Travis; Ward, Chadwich; Apostolova, Liana G.; Ganzola, Rossana; Wolf, Dominik; Barkhof, Frederik; Bartzokis, George; DeCarli, Charles; Csernansky, John G.; deToledo-Morrell, Leyla; Geerlings, Mirjam I.; Kaye, Jeffrey; Killiany, Ronald J.; Lehéricy, Stephane; Matsuda, Hiroshi; O'Brien, John; Silbert, Lisa C.; Scheltens, Philip; Soininen, Hilkka; Teipel, Stefan; Waldemar, Gunhild; Fellgiebel, Andreas; Barnes, Josephine; Firbank, Michael; Gerritsen, Lotte; Henneman, Wouter; Malykhin, Nikolai; Pruessner, Jens C.; Wang, Lei; Watson, Craig; Wolf, Henrike; deLeon, Mony; Pantel, Johannes; Ferrari, Clarissa; Bosco, Paolo; Pasqualetti, Patrizio; Duchesne, Simon; Duvernoy, Henri; Boccardi, Marina

2015-01-01

Background An international Delphi panel has defined a harmonized protocol (HarP) for the manual segmentation of the hippocampus on MR. The aim of this study is to study the concurrent validity of the HarP toward local protocols, and its major sources of variance. Methods Fourteen tracers segmented 10 Alzheimer's Disease Neuroimaging Initiative (ADNI) cases scanned at 1.5 T and 3T following local protocols, qualified for segmentation based on the HarP through a standard web-platform and resegmented following the HarP. The five most accurate tracers followed the HarP to segment 15 ADNI cases acquired at three time points on both 1.5 T and 3T. Results The agreement among tracers was relatively low with the local protocols (absolute left/right ICC 0.44/0.43) and much higher with the HarP (absolute left/right ICC 0.88/0.89). On the larger set of 15 cases, the HarP agreement within (left/right ICC range: 0.94/0.95 to 0.99/0.99) and among tracers (left/right ICC range: 0.89/0.90) was very high. The volume variance due to different tracers was 0.9% of the total, comparing favorably to variance due to scanner manufacturer (1.2), atrophy rates (3.5), hemispheric asymmetry (3.7), field strength (4.4), and significantly smaller than the variance due to atrophy (33.5%, P < .001), and physiological variability (49.2%, P < .001). Conclusions The HarP has high measurement stability compared with local segmentation protocols, and good reproducibility within and among human tracers. Hippocampi segmented with the HarP can be used as a reference for the qualification of human tracers and automated segmentation algorithms. PMID:25267715

Optimality principle for the coupled chemical reactions of ATP synthesis and its molecular interpretation

NASA Astrophysics Data System (ADS)

Nath, Sunil

2018-05-01

Metabolic energy obtained from the coupled chemical reactions of oxidative phosphorylation (OX PHOS) is harnessed in the form of ATP by cells. We experimentally measured thermodynamic forces and fluxes during ATP synthesis, and calculated the thermodynamic efficiency, η and the rate of free energy dissipation, Φ. We show that the OX PHOS system is tuned such that the coupled nonequilibrium processes operate at optimal η. This state does not coincide with the state of minimum Φ but is compatible with maximum Φ under the imposed constraints. Conditions that must hold for species concentration in order to satisfy the principle of optimal efficiency are derived analytically and a molecular explanation based on Nath's torsional mechanism of energy transduction and ATP synthesis is suggested. Differences of the proposed principle with Prigogine's principle are discussed.

Band head spin assignment of superdeformed bands in 133Pr using two-parameter formulae

NASA Astrophysics Data System (ADS)

Sharma, Honey; Mittal, H. M.

2018-03-01

The two-parameter formulae viz. the power index formula, the nuclear softness formula and the VMI model are adopted to accredit the band head spin (I0) of four superdeformed rotational bands in 133Pr. The technique of least square fitting is used to accredit the band head spin for four superdeformed rotational bands in 133Pr. The root mean deviation among the computed transition energies and well-known experimental transition energies are attained by extracting the model parameters from the two-parameter formulae. The determined transition energies are in excellent agreement with the experimental transition energies, whenever exact spins are accredited. The power index formula coincides well with the experimental data and provides minimum root mean deviation. So, the power index formula is more efficient tool than the nuclear softness formula and the VMI model. The deviation of dynamic moment of inertia J(2) against the rotational frequency is also examined.

The angle of shoulder slope in normal males as a factor in shoulder-harness design.

DOT National Transportation Integrated Search

1965-03-01

In order to establish criteria for more comfortable shoulder-harness design, this study was conducted to determine the angle of slope of the top of the shoulders where poorly fitting shoulder harness may produce discomfort and, occasionally, function...

Heading and head injuries in soccer.

PubMed

Kirkendall, D T; Jordan, S E; Garrett, W E

2001-01-01

In the world of sports, soccer is unique because of the purposeful use of the unprotected head for controlling and advancing the ball. This skill obviously places the player at risk of head injury and the game does carry some risk. Head injury can be a result of contact of the head with another head (or other body parts), ground, goal post, other unknown objects or even the ball. Such impacts can lead to contusions, fractures, eye injuries, concussions or even, in rare cases, death. Coaches, players, parents and physicians are rightly concerned about the risk of head injury in soccer. Current research shows that selected soccer players have some degree of cognitive dysfunction. It is important to determine the reasons behind such deficits. Purposeful heading has been blamed, but a closer look at the studies that focus on heading has revealed methodological concerns that question the validity of blaming purposeful heading of the ball. The player's history and age (did they play when the ball was leather and could absorb significant amounts of water), alcohol intake, drug intake, learning disabilities, concussion definition and control group use/composition are all factors that cloud the ability to blame purposeful heading. What does seem clear is that a player's history of concussive episodes is a more likely explanation for cognitive deficits. While it is likely that the subconcussive impact of purposeful heading is a doubtful factor in the noted deficits, it is unknown whether multiple subconcussive impacts might have some lingering effects. In addition, it is unknown whether the noted deficits have any affect on daily life. Proper instruction in the technique is critical because if the ball contacts an unprepared head (as in accidental head-ball contacts), the potential for serious injury is possible. To further our understanding of the relationship of heading, head injury and cognitive deficits, we need to: learn more about the actual impact of a ball on the head, verify the exposure to heading at all ages and competitive levels, determine stable estimates of concussive injury rates across the soccer spectrum, conduct prospective longitudinal studies on soccer players focusing on exposure, injury and cognition, and determine the minimum safe age to begin instruction on the skill of heading. Only then will we be able to speak with some authority on the issue of heading and head injuries in soccer.

Introduction of hand-assisted retroperitoneoscopic living donor nephrectomy at Karolinska University Hospital Huddinge.

PubMed

Gjertsen, H; Sandberg, A-K A; Wadström, J; Tydén, G; Ericzon, B-G

2006-10-01

Living donor kidney transplantation accounts for about 50% of the total number of renal transplantations at our center. From 1999 through 2005, 75 out of 220 living donor nephrectomies were performed with a laparoscopic technique (LLDN). In June 2005, we introduced the technique of hand-assisted retroperitoneoscopic nephrectomy (HARS) for living donors. Since the introduction until the end of 2005, 11 out of 18 living donor nephrectomies (LDN) were performed with HARS. Reduced operation time was observed for the HARS group (mean, 166 minutes) compared with the LLDN (mean, 244 minutes). Two grafts showed delayed function, one in the LLND group and one in the HARS group. No major perioperative or postoperative complications were observed in the HARS group, whereas one patient who underwent LLDN developed severe pancreatitis. So far in our hands HARS is a fast and safe procedure with results comparable with open LDN. Compared to LLDN, we experienced reduced operation time together with the advantage of retroperitoneal access.

A Study on the Performance of the Split Reaction Water Turbine with Guide Ribs

NASA Astrophysics Data System (ADS)

Allen, Deuel H.; Villanueva, Eliseo P.

2015-09-01

The development of technologies that make use of renewable energy is of great significance presently. A new kind of turbine called Split Reaction Water Turbine (SRWT) using PVC pipes as material is a major contribution towards harnessing the energy potentials of small stream low head water resources. SRWTs of diameter to height ratio (D/H = 110 cm/160 cm) were tested at the MSU-IIT College of Engineering Fluid Engineering Laboratory. Data on volumetric flow and pressure head at the turbine inlet of the SRWT were recorded using National Instrument Data Processing System using LabView software. In later experiments, guide ribs were installed at the vane of the exit nozzles in order to determine the difference in the performance of the ribbed and the non-ribbed SRWT. Simulations of the running SRWT were conducted using SOLIDWORKS software. Results of the simulations aided in the thorough analyses of the data from the experimental runs. A comparison of data from the ribbed and non-ribbed SRWT shows that guide ribs were effective in directing the momentum of the exiting water to improve the speed of rotation. In this study, the increase in the speed of the Split Reaction Water Turbine was as much as 46%.

Loss of Consciousness During Single Sling Helicopter Hoist Rescue Resulting in a Fatal Fall.

PubMed

Biles, Jessie; Garner, Alan A

2016-09-01

Although harness suspension trauma has been documented since the 1960s, especially in the mountaineering setting, there is little robust medical research into the area. Helicopter hoist rescue shares similar risks and is reserved for those cases that cannot be accessed safely by other routes, where extrication may be hazardous or will take an unreasonable amount of time. The single sling or chest harness used for hoist rescue is a single harness around the upper torso and is easier and quicker to apply than a stretcher. However, the risks of a chest harness need to be balanced against the patient's condition, the environment, aircraft performance, and the urgency of the rescue. We report an adult male falling 80 ft to his death while being hoisted into a rescue helicopter for a likely fractured ankle. A single rescue sling harness technique was used, but the patient became unconscious, slipped out of the harness, and fell. He had significant comorbidities, including cardiomyopathy, obstructive sleep apnea, morbid obesity, and diabetes. A decrease in cardiac output secondary to thoracic compression was the presumed cause for his loss of consciousness and the potential physiological mechanisms and modifying factors are discussed. Further research into harness suspension trauma is required. Stretcher, double point harnesses, or rescue baskets are likely safer methods of hoisting, especially in a medically compromised patient. Biles J, Garner AA. Loss of consciousness during single sling helicopter hoist rescue resulting in a fatal fall. Aerosp Med Hum Perform. 2016; 87(9):821-824.

Lumbar spine disc heights and curvature: upright posture vs. supine compression harness

NASA Technical Reports Server (NTRS)

Lee, Shi-Uk; Hargens, Alan R.; Fredericson, Michael; Lang, Philipp K.

2003-01-01

INTRODUCTION: Spinal lengthening in microgravity is thought to cause back pain in astronauts. A spinal compression harness can compress the spine to eliminate lengthening but the loading condition with harness is different than physiologic conditions. Our purpose was to compare the effect of spine compression with a harness in supine position on disk height and spinal curvature in the lumbar spine to that of upright position as measured using a vertically open magnetic resonance imaging system. METHODS: Fifteen healthy subjects volunteered. On day 1, each subject lay supine for an hour and a baseline scan of the lumbar spine was performed. After applying a load of fifty percent of body weight with the harness for thirty minutes, the lumbar spine was scanned again. On day 2, after a baseline scan, a follow up scan was performed after kneeling for thirty minutes within the gap between two vertically oriented magnetic coils. Anterior and posterior disk heights, posterior disk bulging, and spinal curvature were measured from the baseline and follow up scans. RESULTS: Anterior disk heights increased and posterior disk heights decreased compared with baseline scans both after spinal compression with harness and upright posture. The spinal curvature increased by both loading conditions of the spine. DISCUSSION: The spinal compression with specially designed harness has the same effect as the physiologic loading of the spine in the kneeling upright position. The harness shows some promise as a tool to increase the diagnostic capabilities of a conventional MR system.

The novel support structure design of high stability for space borne primary reflector

NASA Astrophysics Data System (ADS)

Yu, Fei; Ding, Lin; Tan, Ting; Pei, Jing-yang.; Zhao, Xue-min; Bai, Shao-jun

2018-01-01

The novel support structure design of high stability for space borne primary mirror is presented. The structure is supported by a ball head support rod, for statically determinate support of reflector. The ball head assembly includes the supporting rod, nesting, bushing and other important parts. The liner bushing of the resistant material is used to fit for ball head approximated with the reflector material, and then the bad impact of thermal mismatch could be minimized to minimum. In order to ensure that the structure of the support will not be damaged, the glue spots for limitation is added around the reflector, for position stability of reflector. Through analysis and calculation, it can be seen that the novel support structure would not transfer the external stresses to the reflector, and the external stresses usually result from thermal mismatch and assembly misalignment. The novel method is useful for solving the problem of the bad influence form thermal stress and assembly force. In this paper, the supporting structure is introduced and analyzed in detail. The simulation results show that the ball head support reflector works more stably.

A Strategy to Overcome the Radiology Lottery in the Staging of Head and Neck Cancer: An Aid to Attaining the 30-Day Rule

PubMed Central

Elloy, Marianne; Jarvis, Sara; Davis, Anne

2009-01-01

INTRODUCTION Rapid access to radiological services is essential, if the British Association of Otolaryngologists – Head and Neck Surgeons Minimum Temporal Standards are to be met in the management of head and neck cancer patients. This study assesses a new initiative whereby the multidisciplinary team prioritises allocated imaging appointments rather than using the traditional radiological triage system. PATIENTS AND METHODS This study was a prospective audit of all patients referred over a 3-month period with suspected head and neck cancer. The main outcome measures were: (i) median interval in days from general practitioner (GP) referral to staging scan; and (ii) median interval in days from first clinic appointment to staging scan. RESULTS The new multidisciplinary team booking system led to a statistically significant reduction in the ‘request-to-scan time’ (from 12 days to 5 days). The time from ‘GP to scan’ also improved. CONCLUSIONS This new multidisciplinary team-led booking system, could, in the future, speed up access to radiology services lead and neck cancer patients, allowing earlier definitive treatment. PMID:19126338

14 CFR 27.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... occupant properly uses the seats, safety belts, and shoulder harnesses provided in the design; and (2) The... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact, although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 27.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... occupant properly uses the seats, safety belts, and shoulder harnesses provided in the design; and (2) The... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact, although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 29.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... the seats, safety belts, and shoulder harnesses provided in the design; and (2) The occupant is... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 27.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... occupant properly uses the seats, safety belts, and shoulder harnesses provided in the design; and (2) The... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact, although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 27.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2012 CFR

2012-01-01

... occupant properly uses the seats, safety belts, and shoulder harnesses provided in the design; and (2) The... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact, although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 29.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2014 CFR

2014-01-01

... the seats, safety belts, and shoulder harnesses provided in the design; and (2) The occupant is... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 29.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2011 CFR

2011-01-01

... the seats, safety belts, and shoulder harnesses provided in the design; and (2) The occupant is... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

14 CFR 29.562 - Emergency landing dynamic conditions.

Code of Federal Regulations, 2013 CFR

2013-01-01

... the seats, safety belts, and shoulder harnesses provided in the design; and (2) The occupant is... would cause the greatest load on the shoulder harness), the rotorcraft's lateral axis is contained in a... intact although the structure may have exceeded its limit load. (3) The ATD's shoulder harness strap or...

75 FR 51701 - Airworthiness Directives; Learjet Inc. Model 45 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-23

... configuration of the engine and alternator wire harnesses, and the starter/generator wire bundles. For certain... necessary. For certain airplanes, inspecting for clearance between the wire harnesses and the hydraulic and... wire harnesses and the starter/generator wire bundles. (2) Do a detailed inspection for chafing damage...

Symmetry-adapted perturbation theory interaction energy decomposition for some noble gas complexes

NASA Astrophysics Data System (ADS)

Cukras, Janusz; Sadlej, Joanna

2008-06-01

This Letter contains a study of the interaction energy in HArF⋯N 2 and HArF⋯P 2 complexes. Symmetry-adapted perturbation theory (SAPT) has been applied to analyze the electrostatic, induction, dispersion and exchange contributions to the total interaction energy. The interaction energy has also been obtained by supermolecular method at the MP2, MP4, CCSD, CCSD(T) levels. The interaction energy for the studied complexes results from a partial cancelation of large attractive electrostatic, induction, dispersion terms by a strong repulsive exchange contribution. The induction and dispersion effects proved to be crucial in establishing the preference for the colinear HArF⋯N 2 and HArF⋯P 2 structures and shift direction of νHAr stretching vibrations.

Structural changes and out-of-sample prediction of realized range-based variance in the stock market

NASA Astrophysics Data System (ADS)

Gong, Xu; Lin, Boqiang

2018-03-01

This paper aims to examine the effects of structural changes on forecasting the realized range-based variance in the stock market. Considering structural changes in variance in the stock market, we develop the HAR-RRV-SC model on the basis of the HAR-RRV model. Subsequently, the HAR-RRV and HAR-RRV-SC models are used to forecast the realized range-based variance of S&P 500 Index. We find that there are many structural changes in variance in the U.S. stock market, and the period after the financial crisis contains more structural change points than the period before the financial crisis. The out-of-sample results show that the HAR-RRV-SC model significantly outperforms the HAR-BV model when they are employed to forecast the 1-day, 1-week, and 1-month realized range-based variances, which means that structural changes can improve out-of-sample prediction of realized range-based variance. The out-of-sample results remain robust across the alternative rolling fixed-window, the alternative threshold value in ICSS algorithm, and the alternative benchmark models. More importantly, we believe that considering structural changes can help improve the out-of-sample performances of most of other existing HAR-RRV-type models in addition to the models used in this paper.

Reference standard space hippocampus labels according to the European Alzheimer's Disease Consortium-Alzheimer's Disease Neuroimaging Initiative harmonized protocol: Utility in automated volumetry.

PubMed

Wolf, Dominik; Bocchetta, Martina; Preboske, Gregory M; Boccardi, Marina; Grothe, Michel J

2017-08-01

A harmonized protocol (HarP) for manual hippocampal segmentation on magnetic resonance imaging (MRI) has recently been developed by an international European Alzheimer's Disease Consortium-Alzheimer's Disease Neuroimaging Initiative project. We aimed at providing consensual certified HarP hippocampal labels in Montreal Neurological Institute (MNI) standard space to serve as reference in automated image analyses. Manual HarP tracings on the high-resolution MNI152 standard space template of four expert certified HarP tracers were combined to obtain consensual bilateral hippocampus labels. Utility and validity of these reference labels is demonstrated in a simple atlas-based morphometry approach for automated calculation of HarP-compliant hippocampal volumes within SPM software. Individual tracings showed very high agreement among the four expert tracers (pairwise Jaccard indices 0.82-0.87). Automatically calculated hippocampal volumes were highly correlated (r L/R  = 0.89/0.91) with gold standard volumes in the HarP benchmark data set (N = 135 MRIs), with a mean volume difference of 9% (standard deviation 7%). The consensual HarP hippocampus labels in the MNI152 template can serve as a reference standard for automated image analyses involving MNI standard space normalization. Copyright © 2017 the Alzheimer's Association. Published by Elsevier Inc. All rights reserved.

An attempt to detect lameness in galloping horses by use of body-mounted inertial sensors.

PubMed

Lopes, Marco A F; Dearo, Antonio C O; Lee, Allen; Reed, Shannon K; Kramer, Joanne; Pai, P Frank; Yonezawa, Yoshiharu; Maki, Hiromitchi; Morgan, Terry L; Wilson, David A; Keegan, Kevin G

2016-10-01

OBJECTIVE To evaluate head, pelvic, and limb movement to detect lameness in galloping horses. ANIMALS 12 Thoroughbreds. PROCEDURES Movement data were collected with inertial sensors mounted on the head, pelvis, and limbs of horses trotting and galloping in a straight line before and after induction of forelimb and hind limb lameness by use of sole pressure. Successful induction of lameness was determined by measurement of asymmetric vertical head and pelvic movement during trotting. Differences in gallop strides before and after induction of lameness were evaluated with paired-sample statistical analysis and neural network training and testing. Variables included maximum, minimum, range, and time indices of vertical head and pelvic acceleration, head rotation in the sagittal plane, pelvic rotation in the frontal plane, limb contact intervals, stride durations, and limb lead preference. Difference between median standardized gallop strides for each limb lead before and after induction of lameness was calculated as the sum of squared differences at each time index and assessed with a 2-way ANOVA. RESULTS Head and pelvic acceleration and rotation, limb timing, stride duration measurements, and limb lead preference during galloping were not significantly different before and after induction of lameness in the forelimb or hind limb. Differences between limb leads before induction of lameness were similar to or greater than differences within limb leads before and after lameness induction. CONCLUSIONS AND CLINICAL RELEVANCE Galloping horses maintained asymmetry of head, pelvic, and limb motion between limb leads that was unrelated to lameness.

40 CFR 89.422 - Dilute sampling procedures-CVS calibration.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Pressure depression at CVS pump inlet PPI kPa ±.055 kPa Pressure head at CVS pump outlet PPO kPa ±.055 kPa... restricted condition in an increment of pump inlet depression that will yield a minimum of six data points... depression, (kPa). (iii) The correlation function at each test point is then calculated from the calibration...

40 CFR 89.422 - Dilute sampling procedures-CVS calibration.

Code of Federal Regulations, 2013 CFR

2013-07-01

... Pressure depression at CVS pump inlet PPI kPa ±.055 kPa Pressure head at CVS pump outlet PPO kPa ±.055 kPa... restricted condition in an increment of pump inlet depression that will yield a minimum of six data points... depression, (kPa). (iii) The correlation function at each test point is then calculated from the calibration...

40 CFR 89.422 - Dilute sampling procedures-CVS calibration.

Code of Federal Regulations, 2010 CFR

2010-07-01

... Pressure depression at CVS pump inlet PPI kPa ±.055 kPa Pressure head at CVS pump outlet PPO kPa ±.055 kPa... restricted condition in an increment of pump inlet depression that will yield a minimum of six data points... depression, (kPa). (iii) The correlation function at each test point is then calculated from the calibration...

40 CFR 89.422 - Dilute sampling procedures-CVS calibration.

Code of Federal Regulations, 2012 CFR

2012-07-01

... Pressure depression at CVS pump inlet PPI kPa ±.055 kPa Pressure head at CVS pump outlet PPO kPa ±.055 kPa... restricted condition in an increment of pump inlet depression that will yield a minimum of six data points... depression, (kPa). (iii) The correlation function at each test point is then calculated from the calibration...

40 CFR 89.422 - Dilute sampling procedures-CVS calibration.

Code of Federal Regulations, 2014 CFR

2014-07-01

... Pressure depression at CVS pump inlet PPI kPa ±.055 kPa Pressure head at CVS pump outlet PPO kPa ±.055 kPa... restricted condition in an increment of pump inlet depression that will yield a minimum of six data points... depression, (kPa). (iii) The correlation function at each test point is then calculated from the calibration...

78 FR 77114 - Pacific Gas and Electric Company: Notice of Application Accepted for Filing, Soliciting Comments...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-12-20

... ``exceptionally low inflow'' minimum flow releases outlined in the January 28, 2004. Due to the urgent nature of this request and the potential immediate impacts to fishery resources, the Commission took action on... applicable; (2) set forth in the heading the name of the applicant and the project number of the application...

14 CFR Appendix M to Part 121 - Airplane Flight Recorder Specifications

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Airplane Flight Recorder Specifications M.... 3. Indicated airspeed or Calibrated airspeed 50 KIAS or minimum value to Max Vso to 1.2 V. D ±5% and ±3% 1 1 kt Data should be obtained from the air data computer when practicable. 4. Heading (Primary...

14 CFR Appendix M to Part 121 - Airplane Flight Recorder Specifications

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Airplane Flight Recorder Specifications M.... 3. Indicated airspeed or Calibrated airspeed 50 KIAS or minimum value to Max Vso to 1.2 V. D ±5% and ±3% 1 1 kt Data should be obtained from the air data computer when practicable. 4. Heading (Primary...

14 CFR Appendix M to Part 121 - Airplane Flight Recorder Specifications

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Airplane Flight Recorder Specifications M.... 3. Indicated airspeed or Calibrated airspeed 50 KIAS or minimum value to Max Vso to 1.2 V. D ±5% and ±3% 1 1 kt Data should be obtained from the air data computer when practicable. 4. Heading (Primary...

14 CFR Appendix M to Part 121 - Airplane Flight Recorder Specifications

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Airplane Flight Recorder Specifications M.... 3. Indicated airspeed or Calibrated airspeed 50 KIAS or minimum value to Max Vso to 1.2 V. D ±5% and ±3% 1 1 kt Data should be obtained from the air data computer when practicable. 4. Heading (Primary...

Bipolar femoral head arthroplasty in osteoarthritis. A prospective study with a minimum 5-year follow-up period.

PubMed

Pandit, R

1996-08-01

Primary bipolar femoral head arthroplasties performed on 100 osteoarthritic hips were studied to a minimum of 5 years after surgery. All arthroplasties were performed on physically active patients. At a mean follow-up period of 5.5 years, The Hospital for Special Surgery hip scores were good to excellent in 96 hips. Transient startup soreness constituted the most frequent complaint, occurring in 34 hips. Three hips had more persistent pain localized to the acetabulum, necessitating revision to fixed sockets, which alleviated the symptoms. Four additional hips, in heavy, active men, developed polyethylene fatigue fracture and component disassembly. Acetabular migration of more than 5 mm developed in one hip. Motion, as determined radiologically, occurred primarily at the inner bearing. There were no dislocations or infections in the series. The Bateman bipolar prosthesis provides generally good results in osteoarthritic hips. The shorter operating time and the case of revision are special advantages of bipolar devices. Start-up soreness and stiffness is a shortcoming in approximately one third of cases. Component disassembly in heavy, active men is a problem and the bipolar arthroplasty should be avoided in these patients. Start-up soreness was a significant problem in particular.

Energy management of three-dimensional minimum-time intercept. [for aircraft flight optimization

NASA Technical Reports Server (NTRS)

Kelley, H. J.; Cliff, E. M.; Visser, H. G.

1985-01-01

A real-time computer algorithm to control and optimize aircraft flight profiles is described and applied to a three-dimensional minimum-time intercept mission. The proposed scheme has roots in two well known techniques: singular perturbations and neighboring-optimal guidance. Use of singular-perturbation ideas is made in terms of the assumed trajectory-family structure. A heading/energy family of prestored point-mass-model state-Euler solutions is used as the baseline in this scheme. The next step is to generate a near-optimal guidance law that will transfer the aircraft to the vicinity of this reference family. The control commands fed to the autopilot (bank angle and load factor) consist of the reference controls plus correction terms which are linear combinations of the altitude and path-angle deviations from reference values, weighted by a set of precalculated gains. In this respect the proposed scheme resembles neighboring-optimal guidance. However, in contrast to the neighboring-optimal guidance scheme, the reference control and state variables as well as the feedback gains are stored as functions of energy and heading in the present approach. Some numerical results comparing open-loop optimal and approximate feedback solutions are presented.

Optimal Interception of a Maneuvering Long-range Missile

NASA Astrophysics Data System (ADS)

X. Vinh, Nguyen; T. Kabamba, Pierre; Takehira, Tetsuya

2001-01-01

In a Newtonian central force field, the minimum-fuel interception of a satellite, or a ballistic missile, in elliptic trajectory can be obtained via Lawden's theory of primer vector. To secure interception when the target performs evasive maneuvers, a new control law, with explicit solutions, is implemented. It is shown that by a rotation of coordinate system, the problem of three-dimensional interception is reduced to a planar problem. The general case of planar interception of a long-range ballistic missile is then studied. Examples of interception at a specified time, head-on interception and minimum-fuel interception are presented. In each case, the requirement for the thrust acceleration is expressed explicitly as a function of time.

Quiet Short-Haul Research Airplane (QSRA) model select panel functional description

NASA Technical Reports Server (NTRS)

Watson, D. M.

1982-01-01

The QSRA, when equipped with programmable color cathode ray tube displays, a head up display, a general purpose digital computer and a microwave landing system receiver, will provide a capability to do handling qualities studies and terminal area operating systems experiments as well as to enhance an experimenter's ability to obtain repeatable aircraft performance data. The operating systems experiments include the capability to generate minimum fuel approach and departure paths and to conduct precision approaches to a STOLport runway. The mode select panel is designed to provide both the flexibility needed for a variety of flight test experiments and the minimum workload operation required by pilots flying into congested terminal traffic areas.

Optimal Design and Operation of Permanent Irrigation Systems

NASA Astrophysics Data System (ADS)

Oron, Gideon; Walker, Wynn R.

1981-01-01

Solid-set pressurized irrigation system design and operation are studied with optimization techniques to determine the minimum cost distribution system. The principle of the analysis is to divide the irrigation system into subunits in such a manner that the trade-offs among energy, piping, and equipment costs are selected at the minimum cost point. The optimization procedure involves a nonlinear, mixed integer approach capable of achieving a variety of optimal solutions leading to significant conclusions with regard to the design and operation of the system. Factors investigated include field geometry, the effect of the pressure head, consumptive use rates, a smaller flow rate in the pipe system, and outlet (sprinkler or emitter) discharge.

Design and Analyses of High Aspect Ratio Nozzles for Distributed Propulsion Acoustic Measurements

NASA Technical Reports Server (NTRS)

Dippold, Vance F., III

2016-01-01

A series of three convergent, round-to-rectangular high aspect ratio (HAR) nozzles were designed for acoustic testing at the NASA Glenn Research Center Nozzle Acoustic Test Rig (NATR). The HAR nozzles had exit area aspect ratios of 8:1, 12:1, and 16:1. The nozzles were designed to mimic a distributed propulsion system array with a slot nozzle. The nozzle designs were screened using Reynolds-Averaged Navier-Stokes (RANS) simulations. In addition to meeting the geometric constraints required for testing in the NATR, the HAR nozzles were designed to be free of flow features that would produce unwanted noise (e.g., flow separations) and to have uniform flow at the nozzle exit. Multiple methods were used to generate HAR nozzle designs. The final HAR nozzle designs were generated in segments using a computer code that parameterized each segment. RANS screening simulations showed that intermediate nozzle designs suffered flow separation, a normal shockwave at the nozzle exit (caused by an aerodynamic throat produced by boundary layer growth), and non-uniform flow at the nozzle exit. The RANS simulations showed that the final HAR nozzle designs were free of flow separations, but were not entirely successful at producing a fully uniform flow at the nozzle exit. The final designs suffered a pair of counter-rotating vortices along the outboard walls of the nozzle. The 16:1 aspect ratio HAR nozzle had the least uniform flow at the exit plane; the 8:1 aspect ratio HAR nozzles had a fairly uniform flow at the nozzle exit plane.

Harnessing the Power of Information Technology: Open Business Models in Higher Education

ERIC Educational Resources Information Center

Sheets, Robert G.; Crawford, Stephen

2012-01-01

Higher education is under enormous pressure to improve outcomes and reduce costs. Information technology can help achieve these goals, but only if it is properly harnessed. This article argues that one key to harnessing information technology is business model innovation that results in more "open" and "unbundled" operations in learning and…

14 CFR 135.171 - Shoulder harness installation at flight crewmember stations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 3 2014-01-01 2014-01-01 false Shoulder harness installation at flight... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.171 Shoulder harness installation at flight... configuration, excluding any pilot seat, of 10 seats or more unless it is equipped with an approved shoulder...

14 CFR 135.171 - Shoulder harness installation at flight crewmember stations.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 3 2012-01-01 2012-01-01 false Shoulder harness installation at flight... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.171 Shoulder harness installation at flight... configuration, excluding any pilot seat, of 10 seats or more unless it is equipped with an approved shoulder...

14 CFR 135.171 - Shoulder harness installation at flight crewmember stations.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 3 2013-01-01 2013-01-01 false Shoulder harness installation at flight... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.171 Shoulder harness installation at flight... configuration, excluding any pilot seat, of 10 seats or more unless it is equipped with an approved shoulder...

14 CFR 135.171 - Shoulder harness installation at flight crewmember stations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... 14 Aeronautics and Space 3 2011-01-01 2011-01-01 false Shoulder harness installation at flight... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.171 Shoulder harness installation at flight... configuration, excluding any pilot seat, of 10 seats or more unless it is equipped with an approved shoulder...

14 CFR 135.171 - Shoulder harness installation at flight crewmember stations.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Shoulder harness installation at flight... ON BOARD SUCH AIRCRAFT Aircraft and Equipment § 135.171 Shoulder harness installation at flight... configuration, excluding any pilot seat, of 10 seats or more unless it is equipped with an approved shoulder...

78 FR 57784 - Airworthiness Directives; Airbus Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2013-09-20

... certain wire harness located in the tail cone has wiring of a narrower gauge than design requires. This AD requires replacing the affected wire harness. We are issuing this AD to prevent damage to the affected... production aeroplane, it has been discovered that wires in harness 5877VB, installed in the Tail Cone...

75 FR 36577 - Airworthiness Directives; McDonnell Douglas Corporation Model MD-90-30 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-28

... pump wire harness assembly is routed within the tire burst area and that installing and routing a new and longer auxiliary hydraulic pump wire harness assembly outside the tire burst area will minimize... general visual inspection of the wire harness protective sleeving dimensions, which are related...

Divide and Conquer-Based 1D CNN Human Activity Recognition Using Test Data Sharpening †

PubMed Central

Yoon, Sang Min

2018-01-01

Human Activity Recognition (HAR) aims to identify the actions performed by humans using signals collected from various sensors embedded in mobile devices. In recent years, deep learning techniques have further improved HAR performance on several benchmark datasets. In this paper, we propose one-dimensional Convolutional Neural Network (1D CNN) for HAR that employs a divide and conquer-based classifier learning coupled with test data sharpening. Our approach leverages a two-stage learning of multiple 1D CNN models; we first build a binary classifier for recognizing abstract activities, and then build two multi-class 1D CNN models for recognizing individual activities. We then introduce test data sharpening during prediction phase to further improve the activity recognition accuracy. While there have been numerous researches exploring the benefits of activity signal denoising for HAR, few researches have examined the effect of test data sharpening for HAR. We evaluate the effectiveness of our approach on two popular HAR benchmark datasets, and show that our approach outperforms both the two-stage 1D CNN-only method and other state of the art approaches. PMID:29614767

Divide and Conquer-Based 1D CNN Human Activity Recognition Using Test Data Sharpening.

PubMed

Cho, Heeryon; Yoon, Sang Min

2018-04-01

Human Activity Recognition (HAR) aims to identify the actions performed by humans using signals collected from various sensors embedded in mobile devices. In recent years, deep learning techniques have further improved HAR performance on several benchmark datasets. In this paper, we propose one-dimensional Convolutional Neural Network (1D CNN) for HAR that employs a divide and conquer-based classifier learning coupled with test data sharpening. Our approach leverages a two-stage learning of multiple 1D CNN models; we first build a binary classifier for recognizing abstract activities, and then build two multi-class 1D CNN models for recognizing individual activities. We then introduce test data sharpening during prediction phase to further improve the activity recognition accuracy. While there have been numerous researches exploring the benefits of activity signal denoising for HAR, few researches have examined the effect of test data sharpening for HAR. We evaluate the effectiveness of our approach on two popular HAR benchmark datasets, and show that our approach outperforms both the two-stage 1D CNN-only method and other state of the art approaches.

Osteoblast histogenesis in periodontal ligament and tibial metaphysis during simulated weightlessness

NASA Technical Reports Server (NTRS)

Fielder, Paul J.; Morey, Emily R.; Roberts, W. Eugene

1986-01-01

Utilizing the nuclear morphometric assay for osteoblast histogenesis, the effect of simulated weightlessness (SW) on the relative numbers of the periodontal ligament (PDL) osteoblast progenitors and on the total number of osteogenic cells was determined in rats. Weightlessness was simulated by subjecting rats to continuous 30-deg head-down posture using a modified back-harness device of Morey (1979). The response of a partially unloaded, weight-bearing bone, tibial primary spongiosa (PS), was compared to a normally loaded, nonweight-bearing PDL bone. Data indicated a similar differentiation sequence in PS and PDL, which suggests that these bones might be sensitive to the same systemic factors. Preosteoblast numbers were seen to decrease in both nonweight-bearing and weight-bearing bones during SW (compared with rats not exposed to SW), indicating the importance of systemic mediators, such as cephalad fluid shift, physiological stress, and/or growth retardation.

Regulation of hematopoiesis in rats exposed to antiorthostatic, hypokinetic/hypodynamia. I - Model description

NASA Technical Reports Server (NTRS)

Dunn, C. D. R.; Johnson, P. C.; Lange, R. D.; Perez, L.; Nessel, R.

1985-01-01

The effect of a 7-day suspension in a jacket and harness with 20-deg head-down tilt on body weight, food and water consumption, and hematological parameters is investigated experimentally in male Sprague-Dawley rats weighing 150-175 g. The results are presented in graphs and compared with those for unsuspended controls and with published data on rats and humans exposed to microgravity in space flight. Suspended rats are found to have reduced red-blood-cell mass, erythropoiesis, plasma volume (leading to temporarily increased hematocrit), body weight, and food and water consumption; rightward-shifted oxyhemoglobin-dissociation curves; and unchanged platelet count, leucocyte count or PHA reactivity, and red-blood-cell shape distribution. Since many of these effects are also seen in space flight, the present experimental model is considered a promising technique for simulating the hematopoietic effects of microgravity at 1 g.

Manufacture and quality control of interconnecting wire hardnesses, Volume 1

NASA Technical Reports Server (NTRS)

1972-01-01

A standard is presented for manufacture, installation, and quality control of eight types of interconnecting wire harnesses. The processes, process controls, and inspection and test requirements reflected are based on acknowledgment of harness design requirements, acknowledgment of harness installation requirements, identification of the various parts, materials, etc., utilized in harness manufacture, and formulation of a typical manufacturing flow diagram for identification of each manufacturing and quality control process, operation, inspection, and test. The document covers interconnecting wire harnesses defined in the design standard, including type 1, enclosed in fluorocarbon elastomer convolute, tubing; type 2, enclosed in TFE convolute tubing lines with fiberglass braid; type 3, enclosed in TFE convolute tubing; and type 5, combination of types 3 and 4. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated.

Reducing the rate of early primary hip dislocation by combining a change in surgical technique and an increase in femoral head diameter to 36 mm.

PubMed

Ho, Ki Wai Kevin; Whitwell, George S; Young, Steve K

2012-07-01

We report how changes to our total hip arthroplasty (THA) surgical practise lead to a decrease in early hip dislocation rates. Group B consisted of 421 consecutive primary THA operations performed via a posterior approach. The operative technique included a meticulous repair of the posterior capsule, alignment of the acetabular cup with the transverse acetabular ligament (TAL) and a 36-mm-diameter femoral head. We compared the dislocation rates and cost implications of this technique to a historical control Group A consisting of 389 patients. The control group had their THA performed with no repair of the capsule, no identification of the TAL and all received a 28-mm-diameter head. Our primary outcome is the rate of early hip dislocation and we hypothesised that we can reduce the rate of early hip dislocation with this new regime. In Group B there were no early dislocations (within 6 months) and two (0.5 %) dislocations within 18 months; minimum follow-up time was 18 months with a range of (18-96 months). This compared to a 1.8 % early dislocation rate and a 2.6 % rate at 18 months in Group A; minimum follow-up time was 60 months with a range of (60-112 months). These results were statistically significant (p = 0.006). We suggest that when primary hip arthroplasty is performed through a posterior approach, a low early dislocation rate can be achieved using the described methods.

Measurement of activity coefficients of mixtures by head-space gas chromatography: general procedure.

PubMed

Luis, Patricia; Wouters, Christine; Van der Bruggen, Bart; Sandler, Stanley I

2013-08-09

Head-space gas chromatography (HS-GC) is an applicable method to perform vapor-liquid equilibrium measurements and determine activity coefficients. However, the reproducibility of the data may be conditioned by the experimental procedure concerning to the automated pressure-balanced system. The study developed in this work shows that a minimum volume of liquid in the vial is necessary to ensure the reliability of the activity coefficients since it may become a parameter that influences the magnitude of the peak areas: the helium introduced during the pressurization step may produce significant variations of the results when too small volume of liquid is selected. The minimum volume required should thus be evaluated prior to obtain experimentally the concentration in the vapor phase and the activity coefficients. In this work, the mixture acetonitrile-toluene is taken as example, requiring a sample volume of more than 5mL (about more than 25% of the vial volume). The vapor-liquid equilibrium and activity coefficients of mixtures at different concentrations (0.1, 0.2, 0.3, 0.4, 0.5, 0.6, 0.7, 0.8, 0.9 molar fraction) and four temperatures (35, 45, 55 and 70°C) have been determined. Relative standard deviations (RSD) lower than 5% have been obtained, indicating the good reproducibility of the method when a sample volume larger than 5mL is used. Finally, a general procedure to measure activity coefficients by means of pressure-balanced head-space gas chromatography is proposed. Copyright © 2013 Elsevier B.V. All rights reserved.

Quantitative 3D analysis of bone in hip osteoarthritis using clinical computed tomography.

PubMed

Turmezei, Tom D; Treece, Graham M; Gee, Andrew H; Fotiadou, Anastasia F; Poole, Kenneth E S

2016-07-01

To assess the relationship between proximal femoral cortical bone thickness and radiological hip osteoarthritis using quantitative 3D analysis of clinical computed tomography (CT) data. Image analysis was performed on clinical CT imaging data from 203 female volunteers with a technique called cortical bone mapping (CBM). Colour thickness maps were created for each proximal femur. Statistical parametric mapping was performed to identify statistically significant differences in cortical bone thickness that corresponded with the severity of radiological hip osteoarthritis. Kellgren and Lawrence (K&L) grade, minimum joint space width (JSW) and a novel CT-based osteophyte score were also blindly assessed from the CT data. For each increase in K&L grade, cortical thickness increased by up to 25 % in distinct areas of the superolateral femoral head-neck junction and superior subchondral bone plate. For increasing severity of CT osteophytes, the increase in cortical thickness was more circumferential, involving a wider portion of the head-neck junction, with up to a 7 % increase in cortical thickness per increment in score. Results were not significant for minimum JSW. These findings indicate that quantitative 3D analysis of the proximal femur can identify changes in cortical bone thickness relevant to structural hip osteoarthritis. • CT is being increasingly used to assess bony involvement in osteoarthritis • CBM provides accurate and reliable quantitative analysis of cortical bone thickness • Cortical bone is thicker at the superior femoral head-neck with worse osteoarthritis • Regions of increased thickness co-locate with impingement and osteophyte formation • Quantitative 3D bone analysis could enable clinical disease prediction and therapy development.

Composition, Antifungal and Antiproliferative Activities of the Hydrodistilled Oils from Leaves and Flower Heads of Pterocephalus nestorianus Nábělek.

PubMed

Abdullah, Fuad O; Hussain, Faiq H S; Mannucci, Barbara; Lappano, Rosamaria; Tosi, Solveig; Maggiolini, Marcello; Vidari, Giovanni

2017-07-01

This article reports the first study of the chemical composition, and antifungal and antiproliferative properties of the volatile extracts obtained by hydrodistillation of the flower heads and leaves of the traditional Kurdish medicinal plant Pterocephalus nestorianus Nábělek, collected in the wild. A total of 55 constituents, 43 of the flower heads' oil (PFO) and 46 of the leaves' oil (PLO), respectively, were identified by GC/MS, constituting 99.68% and 99.04% of the two oils, respectively. The oils were obtained in 0.15% and 0.10% yields (w/w), respectively, on air-dried vegetable material. The prevalent constituents of the PFO were α-terpineol (2.41%), α-linalool (6.42%), 6,10,14-trimethylpentadecan-2-one (2.59%), myristic acid (24.65%), and lauric acid (50.44%), while the major components of PLO were (E)-hex-2-enal (2.26%), (E)-hex-2-en-1-ol (2.04), myristic acid (34.03%), and lauric acid (50.35%). The two oils showed significant inhibitory and fungicidal activities against the medically important fungi Candida albicans, Candida tropicalis, Microsporum canis, and Trichophyton mentagrophytes, with minimum inhibitory concentration ranging from 0.7 to 3.3 mg/ml and minimum fungicidal concentration varying from 1.4 to 6.6 mg/ml. The antiproliferative activity of the two oils was assayed against one normal and six human tumor cell lines. Both oils showed selective cytotoxic activity, with IC 50 values ranging from 1.4 to 3.3 μg/ml. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

Documentation of a computer program to simulate aquifer-system compaction using the modular finite-difference ground-water flow model

USGS Publications Warehouse

Leake, S.A.; Prudic, David E.

1988-01-01

The process of permanent compaction is not routinely included in simulations of groundwater flow. To simulate storage changes from both elastic and inelastic compaction, a computer program was written for use with the U. S. Geological Survey modular finite-difference groundwater flow model. The new program is called the Interbed-Storage Package. In the Interbed-Storage Package, elastic compaction or expansion is assumed to be proportional to change in head. The constant of proportionality is the product of skeletal component of elastic specific storage and thickness of the sediments. Similarly, inelastic compaction is assumed to be proportional to decline in head. The constant of proportionality is the product of the skeletal component of inelastic specific storage and the thickness of the sediments. Storage changes are incorporated into the groundwater flow model by adding an additional term to the flow equation. Within a model time step, the package appropriately apportions storage changes between elastic and inelastic components on the basis of the relation of simulated head to the previous minimum head. Another package that allows for a time-varying specified-head boundary is also documented. This package was written to reduce the data requirements for test simulations of the Interbed-Storage Package. (USGS)

European shags optimize their flight behavior according to wind conditions.

PubMed

Kogure, Yukihisa; Sato, Katsufumi; Watanuki, Yutaka; Wanless, Sarah; Daunt, Francis

2016-02-01

Aerodynamics results in two characteristic speeds of flying birds: the minimum power speed and the maximum range speed. The minimum power speed requires the lowest rate of energy expenditure per unit time to stay airborne and the maximum range speed maximizes air distance traveled per unit of energy consumed. Therefore, if birds aim to minimize the cost of transport under a range of wind conditions, they are predicted to fly at the maximum range speed. Furthermore, take-off is predicted to be strongly affected by wind speed and direction. To investigate the effect of wind conditions on take-off and cruising flight behavior, we equipped 14 European shags Phalacrocorax aristotelis with a back-mounted GPS logger to measure position and hence ground speed, and a neck-mounted accelerometer to record wing beat frequency and strength. Local wind conditions were recorded during the deployment period. Shags always took off into the wind regardless of their intended destination and take-off duration was correlated negatively with wind speed. We combined ground speed and direction during the cruising phase with wind speed and direction to estimate air speed and direction. Whilst ground speed was highly variable, air speed was comparatively stable, although it increased significantly during strong head winds, because of stronger wing beats. The increased air speeds in head winds suggest that birds fly at the maximum range speed, not at the minimum power speed. Our study demonstrates that European shags actively adjust their flight behavior to utilize wind power to minimize the costs of take-off and cruising flight. © 2016. Published by The Company of Biologists Ltd.

75 FR 47201 - Airworthiness Directives; Eurocopter France Model EC 130 B4 Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-05

... each electrical harness for chaffing, tears, holes, or other damage at the location of each attachment... electrical harness for any chaffing, tear, hole, or other damage at the location of each attachment screw and... harness for chaffing, a tear, a hole, or other damage at the location of each attachment screw as depicted...

14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems.

Code of Federal Regulations, 2014 CFR

2014-01-01

... 14 Aeronautics and Space 2 2014-01-01 2014-01-01 false Use of safety belts, shoulder harnesses... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child... board is briefed on how to fasten and unfasten that person's safety belt and, if installed, shoulder...

14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems.

Code of Federal Regulations, 2012 CFR

2012-01-01

... 14 Aeronautics and Space 2 2012-01-01 2012-01-01 false Use of safety belts, shoulder harnesses... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child... board is briefed on how to fasten and unfasten that person's safety belt and, if installed, shoulder...

14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems.

Code of Federal Regulations, 2013 CFR

2013-01-01

... 14 Aeronautics and Space 2 2013-01-01 2013-01-01 false Use of safety belts, shoulder harnesses... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child... board is briefed on how to fasten and unfasten that person's safety belt and, if installed, shoulder...

14 CFR 91.107 - Use of safety belts, shoulder harnesses, and child restraint systems.

Code of Federal Regulations, 2010 CFR

2010-01-01

... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Use of safety belts, shoulder harnesses... OPERATING AND FLIGHT RULES Flight Rules General § 91.107 Use of safety belts, shoulder harnesses, and child... board is briefed on how to fasten and unfasten that person's safety belt and, if installed, shoulder...

75 FR 30274 - Airworthiness Directives; McDonnell Douglas Corporation Model MD-11 and MD-11F Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-01

... installed on wire harnesses of the tail tank fuel transfer pumps, and to determine if damaged wires are... a permanent modification of the wire harnesses if metallic transitions are not installed, which... harnesses of the tail tank fuel transfer pumps, and to determine if damaged wires are present; and repair...

75 FR 81433 - Airworthiness Directives; Airbus Model A321-211, -212, -231, and -232 Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2010-12-28

... join individual electrical wires in the Wing Tank harness installations to in-tank equipment on QT... are used to join individual electrical wires in the Wing Tank harness installations to in-tank... electrical wires in the Wing Tank harness installations to in-tank equipment on QT circuit. The failure of a...

Effect Of Water On Permeation By Hydrogen

NASA Technical Reports Server (NTRS)

Tomazic, William A.; Hulligan, David

1988-01-01

Water vapor in working fluid equilibrates with permeability-reducing oxides in metal parts. Report describes study of effects of water on permeation of heater-head tubes by hydrogen in Stirling engine. Experiments performed to determine minimum concentration of oxygen and/or oxygen-bearing gas maintaining oxide coverage adequate for low permeability. Tests showed 750 ppm or more of water effective in maintaining stable, low permeability.

Alternative Fuels Data Center: Fair Oaks Farm Harnesses the Power of

Science.gov Websites

Natural Gas from Cow Manure Fair Oaks Farm Harnesses the Power of Natural Gas from Cow Manure Natural Gas from Cow Manure on Facebook Tweet about Alternative Fuels Data Center: Fair Oaks Farm Harnesses the Power of Natural Gas from Cow Manure on Twitter Bookmark Alternative Fuels Data Center: Fair

75 FR 28478 - Airworthiness Directives; Eurocopter France (ECF) Model AS332L1 and AS332L2 Helicopters

Federal Register 2010, 2011, 2012, 2013, 2014

2010-05-21

... fully tilted the seat shoulder harness could become jammed between the seat and bulkhead. This condition, if not corrected, could result in the shoulder harness binding and causing the inertial reel to... seat backrest is fully tilted, there is a risk of the shoulder harness jamming between the seat and...

75 FR 20423 - Fuji Heavy Industries USA, Inc., Receipt of Petition for Decision of Inconsequential Noncompliance

Federal Register 2010, 2011, 2012, 2013, 2014

2010-04-19

... power supply to the lamp. The Company said that ``installation of the wiring harness to the... subsupplier such that tension was put on the wiring harness connector'' which can cause it to come loose. To correct this problem, the Company has re-routed the wiring harness to ``push'' rather than ``pull'' on the...

Reliability and Validity of the Zephyr[TM] BioHarness[TM] to Measure Respiratory Responses to Exercise

ERIC Educational Resources Information Center

Hailstone, Jono; Kilding, Andrew E.

2011-01-01

The Zephyr[TM] BioHarness[TM] (Zephyr Technology, Auckland, New Zealand) is a wireless physiological monitoring system that has the ability to measure respiratory rate unobtrusively. However, the ability of the BioHarness[TM] to accurately and reproducibly determine respiratory rate across a range of intensities is currently unknown. The aim of…

Wire harness twisting aid

NASA Technical Reports Server (NTRS)

Casey, E. J.; Commadore, C. C.; Ingles, M. E.

1980-01-01

Long wire bundles twist into uniform spiral harnesses with help of simple apparatus. Wires pass through spacers and through hand-held tool with hole for each wire. Ends are attached to low speed bench motor. As motor turns, operator moves hand tool away forming smooth twists in wires between motor and tool. Technique produces harnesses that generate less radio-frequency interference than do irregularly twisted cables.

Manufacturing and quality control of interconnecting wire harnesses, Volume 4

NASA Technical Reports Server (NTRS)

1972-01-01

The document covers interconnecting wire harnesses defined in the design standard, including type 8, flat conductor cable. Volume breadth covers installations of groups of harnesses in a major assembly and the associated post installation inspections and electrical tests. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated into this document.

Circuit For Control Of Electromechanical Prosthetic Hand

NASA Technical Reports Server (NTRS)

Bozeman, Richard J., Jr.

1995-01-01

Proposed circuit for control of electromechanical prosthetic hand derives electrical control signals from shoulder movements. Updated, electronic version of prosthesis, that includes two hooklike fingers actuated via cables from shoulder harness. Circuit built around favored shoulder harness, provides more dexterous movement, without incurring complexity of computer-controlled "bionic" or hydraulically actuated devices. Additional harness and potentiometer connected to similar control circuit mounted on other shoulder. Used to control stepping motor rotating hand about prosthetic wrist to one of number of angles consistent with number of digital outputs. Finger-control signals developed by circuit connected to first shoulder harness transmitted to prosthetic hand via sliprings at prosthetic wrist joint.

Effects of backpack radiotags on female northern pintails wintering in California

USGS Publications Warehouse

Fleskes, Joseph P.

2003-01-01

To test whether backpack radiotags impacted the wintering biology of northern pintails (Anas acuta), I attached spear-suture (SSU, n=82 in 1993) or harness (HAR, n=337 in 1991-1993) backpack radiotags to female Hatch-Year (HY) and After-Hatch-Year (AHY) pintails after their autumn arrival in California. I evaluated impacts of radiotags on 1) wintering population distribution; 2) flock status, flock size, and body mass at harvest; and 3) August-March survival. I also compared retention of SSU and HAR following attachment. Distribution, flock status, and flock size at harvest of HAR, SSU, and unmarked (UMK) pintails were similar. However, harvest mass of HAR pintails averaged 1 33 g (SE=25 g) less than UMK pintails; loss tended to be greatest for heavier HY females in 1 993. Daily survival rates during 1 993-1 994 of HAR vs. SSU pintails were similar for both HY (0.9979 vs. 0.9974) and AHY (0.9988 vs. 0.9986) female pintails. Retention ranged from 30-1 58 days (x=81 d, SE=5 d) for the 37 SSU that I confirmed as being shed; all other SSU failed 1-month studies due to poor retention past a month.

Prenatal head growth and child neuropsychological development at age 14 months.

PubMed

Álamo-Junquera, Dolores; Sunyer, Jordi; Iñiguez, Carmen; Ballester, Ferran; Garcia-Esteban, Raquel; Forns, Joan; Turner, Michelle C; Lertxundi, Aitana; Lertxundi, Nerea; Fernandez-Somoano, Ana; Rodriguez-Dehli, Cristina; Julvez, Jordi

2015-05-01

We sought to assess the association between prenatal head growth and child neuropsychological development in the general population. We evaluated 2104 children at the age of 14 months from a population-based birth cohort in Spain. Head circumference (HC) was measured by ultrasound examinations at weeks 12, 20, and 34 of gestation and by a nurse at birth. Head growth was assessed using conditional SD scores between weeks 12-20 and 20-34. Trained psychologists assessed neuropsychological functioning using the Bayley Scales of Infant Development. Head size measurements at birth were transformed into a 3-category variable: microcephalic (<10th percentile), normocephalic (≥10th and <90th percentile), and macrocephalic (≥90th percentile) based on the cohort distribution. P values<.05 were considered statistically significant. No overall associations were observed between HC or head growth and mental and psychomotor scores. In particular, no associations were found between HC at birth and mental scores (coefficient, 0.04; 95% confidence interval, -0.02 to 0.09) and between interval head growth (20-34 weeks) and mental scores (0.31; 95% confidence interval, -0.36 to 0.99). Upon stratification by microcephalic, normocephalic, or macrocephalic head size, results were imprecise, although there were some significant associations in the microcephalic and macrocephalic groups. Adjustment by various child and maternal cofactors did not affect results. The minimum sample size required for present study was 883 patients (β=2, α=0.05, power=0.80). Overall prenatal and perinatal HC was not associated with 14-month-old neuropsychological development. Findings suggest HC growth during uterine life among healthy infants may not be an important marker of early-life neurodevelopment but may be marginally useful with specific populations. Copyright © 2015 Elsevier Inc. All rights reserved.

Biomechanical analysis of protective countermeasures in underride motor vehicle accidents - biomed 2009.

PubMed

Kumar, Sri; Enz, Bruce; Ponder, Perry L; Anderson, Bob

2009-01-01

Traffic safety has been significantly improved over the past several decades reducing injury and fatality rates. However, there is a paucity of research effort to address the safety issues in underride accidents, specifically the side underride crashes. It is well known that the compromise of occupant space in the vehicle leads to a higher probability of serious or fatal injuries. A better understanding of occupant protection and mechanism of injuries involved in side underride accidents assists in the advancement of safety measures. The present work evaluates the injury potential to occupants during side underride crashes using the car-to-trailer crash methodology. Four crash tests were conducted into the side of a stationary trailer fitted with the side underride guard system (SURG). The SURG used in these tests is 25% lighter than the previous design. A 5th percentile hybrid III female dummy was placed in the driver seat and restrained with the three-point lap and shoulder harness. The anthropometric dummy was instrumented with a head triaxial accelerometer, a chest triaxal accelerometer, a load cell to measure neck force and moment, and a load cell to measure the femur force. The vehicle acceleration was measured using a traxial accelerometer in the rear center tunnel. High speed, standard video and still photos were taken. In all tests, the intrusion was limited to the front structure of the vehicle without any significant compromise to the occupant space. Results indicate that the resultant head and chest accelerations, head injury criterion (HIC), neck force and moment, and femur force were well below the injury tolerance. The present findings support the hypothesis that the SURG not only limits or eliminates the intrusion into the occupant space but also results in biomechanical injury values well below the tolerance limit in motor vehicle crashes.

CheckMate 141: 1-Year Update and Subgroup Analysis of Nivolumab as First-Line Therapy in Patients with Recurrent/Metastatic Head and Neck Cancer.

PubMed

Gillison, Maura L; Blumenschein, George; Fayette, Jerome; Guigay, Joel; Colevas, A Dimitrios; Licitra, Lisa; Harrington, Kevin J; Kasper, Stefan; Vokes, Everett E; Even, Caroline; Worden, Francis; Saba, Nabil F; Iglesias Docampo, Lara Carmen; Haddad, Robert; Rordorf, Tamara; Kiyota, Naomi; Tahara, Makoto; Monga, Manish; Lynch, Mark; Li, Li; Ferris, Robert L

2018-06-04

Nivolumab significantly improved overall survival (OS) vs investigator's choice (IC) of chemotherapy at the primary analysis of randomized, open-label, phase 3 CheckMate 141 in patients with recurrent or metastatic (R/M) squamous cell carcinoma of the head and neck (SCCHN). Here, we report that OS benefit with nivolumab was maintained at a minimum follow-up of 11.4 months. Further, OS benefit with nivolumab vs IC was also noted among patients who received first-line treatment for R/M SCCHN after progressing on platinum therapy for locally advanced disease in the adjuvant or primary (i.e., with radiation) setting. The Oncologist 2018. © AlphaMed Press 2018.

A remote camera operation system using a marker attached cap

NASA Astrophysics Data System (ADS)

Kawai, Hironori; Hama, Hiromitsu

2005-12-01

In this paper, we propose a convenient system to control a remote camera according to the eye-gazing direction of the operator, which is approximately obtained through calculating the face direction by means of image processing. The operator put a marker attached cap on his head, and the system takes an image of the operator from above with only one video camera. Three markers are set up on the cap, and 'three' is the minimum number to calculate the tilt angle of the head. The more markers are used, the robuster system may be made to occlusion, and the wider moving range of the head is tolerated. It is supposed that the markers must not exist on any three dimensional straight line. To compensate the marker's color change due to illumination conditions, the threshold for the marker extraction is adaptively decided using a k-means clustering method. The system was implemented with MATLAB on a personal computer, and the real-time operation was realized. Through the experimental results, robustness of the system was confirmed and tilt and pan angles of the head could be calculated with enough accuracy to use.

[Which hip articulation bearing for which patient? : Tribology of the future].

PubMed

Morlock, M M; Bishop, N; Kaddick, C

2011-12-01

Replacement of the hip joint has become an exceptionally successful procedure since the inauguration of the low friction principle by Charnley. Aseptic osteolysis and joint dislocation have been addressed by the development of wear-optimized materials and the introduction of larger heads. As an increase in head diameter against polyethylene causes wear increase, larger hard-on-hard bearings were introduced, which exhibit reduced wear and reduced dislocation risk with increasing head diameter. These findings were derived from standard simulator testing, not sufficiently considering the risk of fluid film breakdown under adverse conditions, which can cause a dramatic increase in wear and friction proportional to the head diameter. Such adverse conditions can occur clinically in patients due to several factors and have caused the presently observed unexpected problems with these new designs. Standardized preclinical testing has to be viewed as a minimum requirement but certainly not as a guarantee for the clinical success of new materials and designs even if the testing is adapted to the current patient requirements, which is presently not the case. The future of tribology lies in the prevention of adverse conditions in patients, the improvement and optimized use of proven existing materials and not in the use of new materials.

Near-Optimal Re-Entry Trajectories for Reusable Launch Vehicles

NASA Technical Reports Server (NTRS)

Chou, H.-C.; Ardema, M. D.; Bowles, J. V.

1997-01-01

A near-optimal guidance law for the descent trajectory for earth orbit re-entry of a fully reusable single-stage-to-orbit pure rocket launch vehicle is derived. A methodology is developed to investigate using both bank angle and altitude as control variables and selecting parameters that maximize various performance functions. The method is based on the energy-state model of the aircraft equations of motion. The major task of this paper is to obtain optimal re-entry trajectories under a variety of performance goals: minimum time, minimum surface temperature, minimum heating, and maximum heading change; four classes of trajectories were investigated: no banking, optimal left turn banking, optimal right turn banking, and optimal bank chattering. The cost function is in general a weighted sum of all performance goals. In particular, the trade-off between minimizing heat load into the vehicle and maximizing cross range distance is investigated. The results show that the optimization methodology can be used to derive a wide variety of near-optimal trajectories.

Fall Protection Characteristics of Safety Belts and Human Impact Tolerance.

PubMed

Hino, Yasumichi; Ohdo, Katsutoshi; Takahashi, Hiroki

2014-08-23

Many fatal accidents due to falls from heights have occurred at construction sites not only in Japan but also in other countries. This study aims to determine the fall prevention performance of two types of safety belts: a body belt 1) , which has been used for more than 40 yr in the Japanese construction industry as a general type of safety equipment for fall accident prevention, and a full harness 2, 3) , which has been used in many other countries. To determine human tolerance for impact trauma, this study discusses features of safety belts with reference 4-9) to relevant studies in the medical science, automobile crash safety, and aircrew safety. For this purpose, simple drop tests were carried out in a virtual workplace to measure impact load, head acceleration, and posture in the experiments, the Hybrid-III pedestrian model 10) was used as a human dummy. Hybrid-III is typically employed in official automobile crash tests (New Car Assessment Program: NCAP) and is currently recognized as a model that faithfully reproduces dynamic responses. Experimental results shows that safety performance strongly depends on both the variety of safety belts used and the shock absorbers attached onto lanyards. These findings indicate that fall prevention equipment, such as safety belts, lanyards, and shock absorbers, must be improved to reduce impact injuries to the human head and body during falls.

Fall protection characteristics of safety belts and human impact tolerance.

PubMed

Hino, Yasumichi; Ohdo, Katsutoshi; Takahashi, Hiroki

2014-01-01

Many fatal accidents due to falls from heights have occurred at construction sites not only in Japan but also in other countries. This study aims to determine the fall prevention performance of two types of safety belts: a body belt, which has been used for more than 40 yr in the Japanese construction industry as a general type of safety equipment for fall accident prevention, and a full harness, which has been used in many other countries. To determine human tolerance for impact trauma, this study discusses features of safety belts with reference to relevant studies in the medical science, automobile crash safety, and aircrew safety. For this purpose, simple drop tests were carried out in a virtual workplace to measure impact load, head acceleration, and posture in the experiments, the Hybrid-III pedestrian model was used as a human dummy. Hybrid-III is typically employed in official automobile crash tests (New Car Assessment Program: NCAP) and is currently recognized as a model that faithfully reproduces dynamic responses. Experimental results shows that safety performance strongly depends on both the variety of safety belts used and the shock absorbers attached onto lanyards. These findings indicate that fall prevention equipment, such as safety belts, lanyards, and shock absorbers, must be improved to reduce impact injuries to the human head and body during falls.

Fall Protection Characteristics of Safety Belts and Human Impact Tolerance

PubMed Central

HINO, Yasumichi; OHDO, Katsutoshi; TAKAHASHI, Hiroki

2014-01-01

Abstract: Many fatal accidents due to falls from heights have occurred at construction sites not only in Japan but also in other countries. This study aims to determine the fall prevention performance of two types of safety belts: a body belt1), which has been used for more than 40 yr in the Japanese construction industry as a general type of safety equipment for fall accident prevention, and a full harness2, 3), which has been used in many other countries. To determine human tolerance for impact trauma, this study discusses features of safety belts with reference4,5,6,7,8,9) to relevant studies in the medical science, automobile crash safety, and aircrew safety. For this purpose, simple drop tests were carried out in a virtual workplace to measure impact load, head acceleration, and posture in the experiments, the Hybrid-III pedestrian model10) was used as a human dummy. Hybrid-III is typically employed in official automobile crash tests (New Car Assessment Program: NCAP) and is currently recognized as a model that faithfully reproduces dynamic responses. Experimental results shows that safety performance strongly depends on both the variety of safety belts used and the shock absorbers attached onto lanyards. These findings indicate that fall prevention equipment, such as safety belts, lanyards, and shock absorbers, must be improved to reduce impact injuries to the human head and body during falls. PMID:25345426

Forecasting the value-at-risk of Chinese stock market using the HARQ model and extreme value theory

NASA Astrophysics Data System (ADS)

Liu, Guangqiang; Wei, Yu; Chen, Yongfei; Yu, Jiang; Hu, Yang

2018-06-01

Using intraday data of the CSI300 index, this paper discusses value-at-risk (VaR) forecasting of the Chinese stock market from the perspective of high-frequency volatility models. First, we measure the realized volatility (RV) with 5-minute high-frequency returns of the CSI300 index and then model it with the newly introduced heterogeneous autoregressive quarticity (HARQ) model, which can handle the time-varying coefficients of the HAR model. Second, we forecast the out-of-sample VaR of the CSI300 index by combining the HARQ model and extreme value theory (EVT). Finally, using several popular backtesting methods, we compare the VaR forecasting accuracy of HARQ model with other traditional HAR-type models, such as HAR, HAR-J, CHAR, and SHAR. The empirical results show that the novel HARQ model can beat other HAR-type models in forecasting the VaR of the Chinese stock market at various risk levels.

A Regulatory Pathway, Ecdysone-Transcription Factor Relish-Cathepsin L, Is Involved in Insect Fat Body Dissociation

PubMed Central

Zhang, Yao; Lu, Yu-Xuan; Liu, Jian; Yang, Cui; Feng, Qi-Li; Xu, Wei-Hua

2013-01-01

Insect fat body is the organ for intermediary metabolism, comparable to vertebrate liver and adipose tissue. Larval fat body is disintegrated to individual fat body cells and then adult fat body is remodeled at the pupal stage. However, little is known about the dissociation mechanism. We find that the moth Helicoverpa armigera cathepsin L (Har-CL) is expressed heavily in the fat body and is released from fat body cells into the extracellular matrix. The inhibitor and RNAi experiments demonstrate that Har-CL functions in the fat body dissociation in H. armigera. Further, a nuclear protein is identified to be transcription factor Har-Relish, which was found in insect immune response and specifically binds to the promoter of Har-CL gene to regulate its activity. Har-Relish also responds to the steroid hormone ecdysone. Thus, the dissociation of the larval fat body is involved in the hormone (ecdysone)-transcription factor (Relish)-target gene (cathepsin L) regulatory pathway. PMID:23459255

Sub-Saharan Africa Report, No. 2817.

DTIC Science & Technology

1983-07-06

between the two countries. During his visit to Montevideo, he will deliver a personal message from the head of state, El Hadj Omar Bongo , to his...inception. The spokesman said that unless (Khaketla) could manage to attract the minimum affection from the people of Lesotho he would never have the...socialist countries would affect religion adversely. [Text] [MB180718 Maseru Domestic Service in English 0500 GMT 18 Jun 83] JONATHAN TOUR—The

Harnessing the Power of Light to See and Treat Breast Cancer

DTIC Science & Technology

2010-10-01

Harnessing the power of light to see and treat breast cancer PRINCIPAL INVESTIGATOR: Nirmala Ramanujam, Ph.D...NUMBER Harnessing the power of light to see and treat breast cancer . 5b. GRANT NUMBER W81XWH-09-1-0410 5c. PROGRAM ELEMENT NUMBER 6...optical contrast to develop novel strategies that focus on two breast cancer applications: tumor margin assessment and prediction of response to neo

Evaluation of Cable Harness Post-Installation Testing. Part B

NASA Technical Reports Server (NTRS)

King, M. S.; Iannello, C. J.

2011-01-01

The Cable Harness Post-Installation Testing Report was written in response to an action issued by the Ares Project Control Board (PCB). The action for the Ares I Avionics & Software Chief Engineer and the Avionics Integration and Vehicle Systems Test Work Breakdown Structure (WBS) Manager in the Vehicle Integration Office was to develop a set of guidelines for electrical cable harnesses. Research showed that post-installation tests have been done since the Apollo era. For Ares I-X, the requirement for post-installation testing was removed to make it consistent with the avionics processes used on the Atlas V expendable launch vehicle. Further research for the report involved surveying government and private sector launch vehicle developers, military and commercial aircraft, spacecraft developers, and harness vendors. Responses indicated crewed launch vehicles and military aircraft perform post-installation tests. Key findings in the report were as follows: Test requirements identify damage, human-rated vehicles should be tested despite the identification of statistically few failures, data does not support the claim that post-installation testing damages the harness insulation system, and proper planning can reduce overhead associated with testing. The primary recommendation of the report is for the Ares projects to retain the practice of post-fabrication and post-installation cable harness testing.

Sharp-Tip Silver Nanowires Mounted on Cantilevers for High-Aspect-Ratio High-Resolution Imaging.

PubMed

Ma, Xuezhi; Zhu, Yangzhi; Kim, Sanggon; Liu, Qiushi; Byrley, Peter; Wei, Yang; Zhang, Jin; Jiang, Kaili; Fan, Shoushan; Yan, Ruoxue; Liu, Ming

2016-11-09

Despite many efforts to fabricate high-aspect-ratio atomic force microscopy (HAR-AFM) probes for high-fidelity, high-resolution topographical imaging of three-dimensional (3D) nanostructured surfaces, current HAR probes still suffer from unsatisfactory performance, low wear-resistivity, and extravagant prices. The primary objective of this work is to demonstrate a novel design of a high-resolution (HR) HAR AFM probe, which is fabricated through a reliable, cost-efficient benchtop process to precisely implant a single ultrasharp metallic nanowire on a standard AFM cantilever probe. The force-displacement curve indicated that the HAR-HR probe is robust against buckling and bending up to 150 nN. The probes were tested on polymer trenches, showing a much better image fidelity when compared with standard silicon tips. The lateral resolution, when scanning a rough metal thin film and single-walled carbon nanotubes (SW-CNTs), was found to be better than 8 nm. Finally, stable imaging quality in tapping mode was demonstrated for at least 15 continuous scans indicating high resistance to wear. These results demonstrate a reliable benchtop fabrication technique toward metallic HAR-HR AFM probes with performance parallel or exceeding that of commercial HAR probes, yet at a fraction of their cost.

Advances and limitations of visual conditioning protocols in harnessed bees.

PubMed

Avarguès-Weber, Aurore; Mota, Theo

2016-10-01

Bees are excellent invertebrate models for studying visual learning and memory mechanisms, because of their sophisticated visual system and impressive cognitive capacities associated with a relatively simple brain. Visual learning in free-flying bees has been traditionally studied using an operant conditioning paradigm. This well-established protocol, however, can hardly be combined with invasive procedures for studying the neurobiological basis of visual learning. Different efforts have been made to develop protocols in which harnessed honey bees could associate visual cues with reinforcement, though learning performances remain poorer than those obtained with free-flying animals. Especially in the last decade, the intention of improving visual learning performances of harnessed bees led many authors to adopt distinct visual conditioning protocols, altering parameters like harnessing method, nature and duration of visual stimulation, number of trials, inter-trial intervals, among others. As a result, the literature provides data hardly comparable and sometimes contradictory. In the present review, we provide an extensive analysis of the literature available on visual conditioning of harnessed bees, with special emphasis on the comparison of diverse conditioning parameters adopted by different authors. Together with this comparative overview, we discuss how these diverse conditioning parameters could modulate visual learning performances of harnessed bees. Copyright © 2016 Elsevier Ltd. All rights reserved.

The Usher Syndrome Type IIIB Histidyl-tRNA Synthetase Mutation Confers Temperature Sensitivity.

PubMed

Abbott, Jamie A; Guth, Ethan; Kim, Cindy; Regan, Cathy; Siu, Victoria M; Rupar, C Anthony; Demeler, Borries; Francklyn, Christopher S; Robey-Bond, Susan M

2017-07-18

Histidyl-tRNA synthetase (HARS) is a highly conserved translation factor that plays an essential role in protein synthesis. HARS has been implicated in the human syndromes Charcot-Marie-Tooth (CMT) Type 2W and Type IIIB Usher (USH3B). The USH3B mutation, which encodes a Y454S substitution in HARS, is inherited in an autosomal recessive fashion and associated with childhood deafness, blindness, and episodic hallucinations during acute illness. The biochemical basis of the pathophysiologies linked to USH3B is currently unknown. Here, we present a detailed functional comparison of wild-type (WT) and Y454S HARS enzymes. Kinetic parameters for enzymes and canonical substrates were determined using both steady state and rapid kinetics. Enzyme stability was examined using differential scanning fluorimetry. Finally, enzyme functionality in a primary cell culture was assessed. Our results demonstrate that the Y454S substitution leaves HARS amino acid activation, aminoacylation, and tRNA His binding functions largely intact compared with those of WT HARS, and the mutant enzyme dimerizes like the wild type does. Interestingly, during our investigation, it was revealed that the kinetics of amino acid activation differs from that of the previously characterized bacterial HisRS. Despite the similar kinetics, differential scanning fluorimetry revealed that Y454S is less thermally stable than WT HARS, and cells from Y454S patients grown at elevated temperatures demonstrate diminished levels of protein synthesis compared to those of WT cells. The thermal sensitivity associated with the Y454S mutation represents a biochemical basis for understanding USH3B.

Probing the accuracy and precision of Hirshfeld atom refinement with HARt interfaced with Olex2.

PubMed

Fugel, Malte; Jayatilaka, Dylan; Hupf, Emanuel; Overgaard, Jacob; Hathwar, Venkatesha R; Macchi, Piero; Turner, Michael J; Howard, Judith A K; Dolomanov, Oleg V; Puschmann, Horst; Iversen, Bo B; Bürgi, Hans-Beat; Grabowsky, Simon

2018-01-01

Hirshfeld atom refinement (HAR) is a novel X-ray structure refinement technique that employs aspherical atomic scattering factors obtained from stockholder partitioning of a theoretically determined tailor-made static electron density. HAR overcomes many of the known limitations of independent atom modelling (IAM), such as too short element-hydrogen distances, r ( X -H), or too large atomic displacement parameters (ADPs). This study probes the accuracy and precision of anisotropic hydrogen and non-hydrogen ADPs and of r ( X -H) values obtained from HAR. These quantities are compared and found to agree with those obtained from (i) accurate neutron diffraction data measured at the same temperatures as the X-ray data and (ii) multipole modelling (MM), an established alternative method for interpreting X-ray diffraction data with the help of aspherical atomic scattering factors. Results are presented for three chemically different systems: the aromatic hydro-carbon rubrene (orthorhombic 5,6,11,12-tetra-phenyl-tetracene), a co-crystal of zwitterionic betaine, imidazolium cations and picrate anions (BIPa), and the salt potassium hydrogen oxalate (KHOx). The non-hydrogen HAR-ADPs are as accurate and precise as the MM-ADPs. Both show excellent agreement with the neutron-based values and are superior to IAM-ADPs. The anisotropic hydrogen HAR-ADPs show a somewhat larger deviation from neutron-based values than the hydrogen SHADE-ADPs used in MM. Element-hydrogen bond lengths from HAR are in excellent agreement with those obtained from neutron diffraction experiments, although they are somewhat less precise. The residual density contour maps after HAR show fewer features than those after MM. Calculating the static electron density with the def2-TZVP basis set instead of the simpler def2-SVP one does not improve the refinement results significantly. All HARs were performed within the recently introduced HARt option implemented in the Olex2 program. They are easily launched inside its graphical user interface following a conventional IAM.

Minimizing marker mass and handling time when attaching radio-transmitters and geolocators to small songbirds

USGS Publications Warehouse

Streby, Henry M.; McAllister, Tara L.; Peterson, Sean M.; Kramer, Gunnar R.; Lehman, Justin A.; Andersen, David E.

2015-01-01

Radio-transmitters and light-level geolocators are currently small enough for use on songbirds weighing <15 g. Various methods are used to attach these markers to larger songbirds, but with small birds it becomes especially important to minimize marker mass and bird handling time. Here, we offer modifications to harness materials and marker preparation for transmitters and geolocators, and we describe deployment methods that can be safely completed in 20–60 s per bird. We describe a 0.5-mm elastic sewing thread harness for radio-transmitters that allows nestlings, fledglings, and adults to be marked with the same harness size and reliably falls off to avoid poststudy effects. We also describe a 0.5-mm jewelry cord harness for geolocators that provides a firm fit for >1 yr. Neither harness type requires plastic or metal tubes, rings, or other attachment fixtures on the marker, nor do they require crimping beads, epoxy, scissors, or tying knots while handling birds. Both harnesses add 0.03 g to the mass of markers for small wood-warblers (Parulidae). This minimal additional mass is offset by trimming transmitter antennas or geolocator connection nodes, resulting in no net mass gain for transmitters and 0.02 g added for geolocators compared with conventional harness methods that add >0.40 g. We and others have used this transmitter attachment method with several small songbird species, with no effects on adult and fledgling behavior and survival. We have used this geolocator attachment method on 9-g wood-warblers with no effects on return rates, return dates, territory fidelity, and body mass. We hope that these improvements to the design and deployment of the leg-loop harness method will enable the safe and successful use of these markers, and eventually GPS and other tags, on similarly small songbirds.

Probing the accuracy and precision of Hirshfeld atom refinement with HARt interfaced with Olex2

PubMed Central

Fugel, Malte; Hathwar, Venkatesha R.; Turner, Michael J.; Howard, Judith A. K.

2018-01-01

Hirshfeld atom refinement (HAR) is a novel X-ray structure refinement technique that employs aspherical atomic scattering factors obtained from stockholder partitioning of a theoretically determined tailor-made static electron density. HAR overcomes many of the known limitations of independent atom modelling (IAM), such as too short element–hydrogen distances, r(X—H), or too large atomic displacement parameters (ADPs). This study probes the accuracy and precision of anisotropic hydrogen and non-hydrogen ADPs and of r(X—H) values obtained from HAR. These quantities are compared and found to agree with those obtained from (i) accurate neutron diffraction data measured at the same temperatures as the X-ray data and (ii) multipole modelling (MM), an established alternative method for interpreting X-ray diffraction data with the help of aspherical atomic scattering factors. Results are presented for three chemically different systems: the aromatic hydro­carbon rubrene (orthorhombic 5,6,11,12-tetra­phenyl­tetracene), a co-crystal of zwitterionic betaine, imidazolium cations and picrate anions (BIPa), and the salt potassium hydrogen oxalate (KHOx). The non-hydrogen HAR-ADPs are as accurate and precise as the MM-ADPs. Both show excellent agreement with the neutron-based values and are superior to IAM-ADPs. The anisotropic hydrogen HAR-ADPs show a somewhat larger deviation from neutron-based values than the hydrogen SHADE-ADPs used in MM. Element–hydrogen bond lengths from HAR are in excellent agreement with those obtained from neutron diffraction experiments, although they are somewhat less precise. The residual density contour maps after HAR show fewer features than those after MM. Calculating the static electron density with the def2-TZVP basis set instead of the simpler def2-SVP one does not improve the refinement results significantly. All HARs were performed within the recently introduced HARt option implemented in the Olex2 program. They are easily launched inside its graphical user interface following a conventional IAM. PMID:29354269

Are the results of multiple drilling and alendronate for osteonecrosis of the femoral head better than those of multiple drilling? A pilot study.

PubMed

Kang, Pengde; Pei, Fuxing; Shen, Bin; Zhou, Zongke; Yang, Jing

2012-01-01

The treatment of osteonecrosis of the femoral head (ONFH) remains controversial. A recently proposed treatment is multiple drilling core decompression combined with systemic alendronate as a femoral head-preserving procedure for ONFH. However, it is not known whether alendronate enhances the risk of collapse. We wondered whether the combined procedure could delay or prevent progression of ONFH compared to multiple drilling alone. Patients with early-stage ONFH were randomly assigned to be treated with either multiple drilling combined with alendronate (47 patients, 67 hips) or multiple drilling alone (46 patients, 60 hips). We defined failure as the need for THA or a Harris score less than 70. The minimum follow-up was 48 months for the 77 patients completing the protocol. After a minimum 4-year follow-up, 91% (40/44) of patients with Stage II disease and 62% (8/13) of patients with Stage III disease had not required THA in alendronate group, compared to 79% (31/39) of patients with Stage II disease and 46% (6/13) of patients with Stage III disease had not required THA in control group (P=0.12, P=0.047, respectively). Small or medium and central lesions had a better successful rate in both groups. Risk factors did not seem to affect the clinical successful rate of this procedure. Multiple small-diameter drilling core decompression combined with systemic alendronate administration can reduce pain and delay progression of early-stage ONFH. Even in Ficat IIA and III hips, some benefit was obtained from this approach at least delay in the need for THA. Copyright © 2011. Published by Elsevier SAS.

Thermal comfort zone of the hands, feet and head in males and females.

PubMed

Ciuha, Urša; Mekjavic, Igor B

2017-10-01

The present study compared the thermal comfort zones (TCZ) of the hands, feet and head in eight male and eight female participants, assessed with water-perfused segments (WPS). On separate occasions, and separated by a minimum of one day, participants were requested to regulate the temperature of three distal skin regions (hands, feet and head) within their TCZ. On each occasion they donned a specific water-perfused segment (WPS), either gloves, socks or hood for assessing the TCZ of the hands, feet and head, respectively. In the absence of regulation, the temperature of the water perfusing the WPS changed in a saw-tooth manner from 10 to 50°C; by depressing a switch and reversing the direction of the temperature at the limits of the TCZ, each participant defined the TCZ for each skin region investigated. The range of regulated temperatures (upper and lower limits of the TCZ) did not differ between studied skin regions or between genders. Participants however maintained higher head (35.7±0.4°C; p˂0.001) skin temperature (Tsk) compared to hands (34.5±0.8°C) and feet (33.8±1.1°C). When exposed to normothermic conditions, distal skin regions do not differ in ranges of temperatures, perceived as thermally comfortable. Copyright © 2017. Published by Elsevier Inc.

Hydrologic and hydraulic factors affecting passage of paddlefish through dams in the Upper Mississippi River

USGS Publications Warehouse

Zigler, S.J.; Dewey, M.R.; Knights, B.C.; Runstrom, A.L.; Steingraeber, M.T.

2004-01-01

Populations of paddlefish Polyodon spathula have been adversely affected by dams that can block their movements. Unlike high-head dams that preclude fish passage (unless they are equipped with fishways), the dams on the upper Mississippi River are typically low-head dams with bottom release gates that may allow fish passage under certain conditions. We evaluated the relation of dam head and river discharge to the passage of radio-tagged paddlefish through dams in the upper Mississippi River. Radio transmitters were surgically implanted into 71 paddlefish from Navigation Pools 5A and 8 of the upper Mississippi River and from two tributary rivers during fall 1994 through fall 1996. We tracked paddlefish through September 1997 and documented 53 passages through dams, 20 upstream and 33 downstream. Passages occurred mostly during spring (71%) but also occurred sporadically during summer and fall (29%). Spring passages varied among years in response to hydrologic conditions. We evaluated patterns in upstream and downstream passages with Cox proportional hazard regression models. Model results indicated that dam head height strongly affected the upstream passage of paddlefish but not the downstream passage. Several paddlefish, however, passed upstream through a dam during periods when the minimum head at the dam was substantial ( greater than or equal to 1m). In these cases, we hypothesize that paddlefish moved upstream through the lock chamber.

Vertical movement symmetry of the withers in horses with induced forelimb and hindlimb lameness at trot.

PubMed

Rhodin, M; Persson-Sjodin, E; Egenvall, A; Serra Bragança, F M; Pfau, T; Roepstorff, L; Weishaupt, M A; Thomsen, M H; van Weeren, P R; Hernlund, E

2018-04-15

The main criteria for lameness assessment in horses are head movement for forelimb lameness and pelvic movement for hindlimb lameness. However, compensatory head nod in horses with primary hindlimb lameness is a well-known phenomenon. This compensatory head nod movement can be easily misinterpreted as a sign of primary ipsilateral forelimb lameness. Therefore, discriminating compensatory asymmetries from primary directly pain-related movement asymmetries is a prerequisite for successful lameness assessment. To investigate the association between head, withers and pelvis movement asymmetry in horses with induced forelimb and hindlimb lameness. Experimental study. In 10 clinically sound Warmblood riding horses, forelimb and hindlimb lameness were induced using a sole pressure model. The horses were then trotted on a treadmill. Three-dimensional optical motion capture was used to collect kinematic data from reflective markers attached to the poll, withers and tubera sacrale. The magnitude and side (left or right) of the following symmetry parameters, vertical difference in minimum position, maximum position and range-up were calculated for head, withers, and pelvis. Mixed models were used to analyse data from induced forelimb and hindlimb lameness. For each mm increase in pelvic asymmetry in response to hindlimb lameness induction, withers movement asymmetry increased by 0.35-0.55 mm, but towards the contralateral side. In induced forelimb lameness, for each mm increase in head movement asymmetry, withers movement asymmetry increased by 0.05-0.10 mm, in agreement with the head movement asymmetry direction, both indicating lameness in the induced forelimb. Results must be confirmed in clinically lame horses trotting overground. The vertical asymmetry pattern of the withers discriminated a head nod associated with true forelimb lameness from the compensatory head movement asymmetry caused by primary hindlimb lameness. Measuring movement symmetry of the withers may, thus, aid in determining primary lameness location. © 2018 The Authors. Equine Veterinary Journal published by John Wiley & Sons Ltd on behalf of EVJ Ltd.

Helmet legislation and admissions to hospital for cycling related head injuries in Canadian provinces and territories: interrupted time series analysis

PubMed Central

Ramsay, Tim; Turgeon, Alexis F; Zarychanski, Ryan

2013-01-01

Objective To investigate the association between helmet legislation and admissions to hospital for cycling related head injuries among young people and adults in Canada. Design Interrupted time series analysis using data from the National Trauma Registry Minimum Data Set. Setting Canadian provinces and territories; between 1994 and 2003, six of 10 provinces implemented helmet legislation. Participants All admissions (n=66 716) to acute care hospitals in Canada owing to cycling related injury between 1994 and 2008. Main outcome measure Rate of admissions to hospital for cycling related head injuries before and after the implementation of provincial helmet legislation. Results Between 1994 and 2008, 66 716 hospital admissions were for cycling related injuries in Canada. Between 1994 and 2003, the rate of head injuries among young people decreased by 54.0% (95% confidence interval 48.2% to 59.8%) in provinces with helmet legislation compared with 33.1% (23.3% to 42.9%) in provinces and territories without legislation. Among adults, the rate of head injuries decreased by 26.0% (16.0% to 36.3%) in provinces with legislation but remained constant in provinces and territories without legislation. After taking baseline trends into consideration, however, we were unable to detect an independent effect of legislation on the rate of hospital admissions for cycling related head injuries. Conclusions Reductions in the rates of admissions to hospital for cycling related head injuries were greater in provinces with helmet legislation, but injury rates were already decreasing before the implementation of legislation and the rate of decline was not appreciably altered on introduction of legislation. While helmets reduce the risk of head injuries and we encourage their use, in the Canadian context of existing safety campaigns, improvements to the cycling infrastructure, and the passive uptake of helmets, the incremental contribution of provincial helmet legislation to reduce hospital admissions for head injuries seems to have been minimal. PMID:23674137

Compliant walker

NASA Technical Reports Server (NTRS)

Kerley, James J. (Inventor); Eklund, Wayne D. (Inventor); Crane, J. Allen (Inventor)

1992-01-01

A compliant walker is provided for humans having limited use of their legs and lower back. It includes an upright wheel frame which at least partially surrounds an upright user wearing a partial body harness. It is attached to the frame by means of cable compliant apparatus consisting of sets of cable segments and angle bracket members connected between opposite side members of the frame and adjacent side portions of the harness. Novelty is believed to exist in the combination of a wheeled frame including a side support structure, a body harness, and compliance means connecting the body harness to the side support structure for flexibility holding and supporting a person in a substantially upright position when the user sags in the frame when taking weight off the lower extremities.

Semireal Time Monitoring Of The Functional Movements Of The Mandible

NASA Astrophysics Data System (ADS)

Isaacson, Robert J.; Baumrind, Sheldon; Curry, Sean; Molthen, Robert A.

1983-07-01

Many branches of dental practice would benefit from the availability of a relatively accurate, precise, and efficient method for monitoring the movements of the human mandible during function. Mechanical analog systems have been utilized in the past but these are difficult to quantify, have limited accuracy due to frictional resistance of the components, and contain information only on the borders of the envelopes of possible movement of the landmarks measured (rather than on the functional paths of the landmarks which lie within their envelopes). Those electronic solutions which have been attempted thus far have been prohibitively expensive and time consuming for clinical use, have had lag times between data acquisition and display, or have involved such restrictions of freedom of motion as to render ambiguous the meaning of the data obtained. We report work aimed at developing a relatively non-restrictive semi-real time acoustical system for monitoring the functional movement of the mandible relative to the rest of the head. A set of three sparking devices is mounted to the mandibular component of a light, relatively non-constraining extra-oral harness and another set of three sparkers is attached to the harness' cranial or skull component. The sparkers are fired sequentially by a multiplexer and the sound associated with each firing is recorded by an array of three or more microphones. Computations based on the known speed of sound are used to evaluate the distances between the sparkers and the microphones. These data can then be transformed by computer to provide numeric or graphic information on the movement of selected mandibular landmarks with respect to the skull. Total elapsed time between the firing of the sparkers and the display of graphic information need not exceed 30-60 seconds using even a relatively modest modern computer.

Wealth status and sex differential of household head: implication for source of drinking water in Nigeria.

PubMed

Morakinyo, Oyewale Mayowa; Adebowale, Stephen Ayo; Oloruntoba, Elizabeth Omoladun

2015-01-01

Source of potable water has implication on the population health. Availability of Improved Drinking Water Sources (IDWS) is a problem in developing countries, but variation exists across segments of the population. This study therefore examined the relationship between wealth status, sex of household head and source of potable water. The 2013 Nigeria Demographic and Health Survey data was used. A representative sample of 40,680 households was selected for the survey, with a minimum target of 943 completed interviews per state covering the entire population residing in non-institutional dwelling units in the country. Households where information on drinking water sources was not reported were excluded, thus reducing the sample to 38021. The dependent and key independent variables were IDWS and Wealth Index respectively. Data were analysed using Chi-square and binary logistic regression (α = .05). Households that used IDWS were headed by females (66.7 %) than males (58.7 %). Highest proportion of households who used IDWS was found in the rich wealth index group (76.7 %). The likelihood of using IDWS was higher in household headed by females (OR = 1.41; C.I = 1.33-1.49, p <0.001). Households that belong to rich wealth index and middle class were 5.06(C.I = 4.81-5.32, p <0.001) and 2.62(C.I = 2.46-2.78, p <0.001) respectively times more likely to IDWS than the poor. This pattern was sustained when other confounding variables were introduced into the regression equation as control. Households headed by women used improved drinking water sources than those headed by men. However, wealth index has strong influence on the strength of relationship between sex of household head and improved drinking water sources.

[Paragangliomas of the head and neck. Our experience].

PubMed

Alvarez Zapico, M J; Llorente Pendás, J L; Suárez Nieto, C; Carreño Villarreal, M; Moro Melón, M

1998-04-01

Paragangliomas of the head and neck are rare tumors of neuroectodermal origin. However, jugulotympanic paragangliomas are the second most common tumor of the temporal bone. Paragangliomas are recognized as benign tumors, but some show a biological behavior similar to that of malignant lesions, such as the development of recurrence or invasive growth patterns. We report 31 patients with a total of 35 paragangliomas who were seen in our department. Multiple paragangliomas were found in 2 patients. Twenty-two patients had jugulotympanic paragangliomas, 11 carotid and 2 vagal paragangliomas. None of the patients had prior treatment and the minimum follow-up was 1 year. Surgery was performed in 28 (90%), primary irradiation in 1 (3%), and 2 (7%) refused treatment. We describe our results, the clinical course, diagnostic methods and treatment options.

Effects of satellite transmitters on captive and wild mallards

USGS Publications Warehouse

Kesler, Dylan C.; Raedeke, Andrew H.; Foggia, Jennifer R.; Beatty, William S.; Webb, Elisabeth B.; Humburg, Dale D.; Naylor, Luke W.

2014-01-01

Satellite telemetry has become a leading method for studying large-scale movements and survival in birds, yet few have addressed potential effects of the larger and heavier tracking equipment on study subjects. We simultaneously evaluated effects of satellite telemetry equipment on captive and wild mallards (Anas platyrhynchos) to assess impacts on behavior, body mass, and movement. We randomly assigned 55 captive ducks to one of 3 treatment groups, including a standard body harness group, a modified harness group, and a control group. Ducks in the control group were not fitted with equipment, whereas individuals in the other 2 groups were fitted with dummy transmitters attached with a Teflon ribbon harness or with a similar harness constructed of nylon cord. At the conclusion of the 14-week captive study, mean body mass of birds in the control group was 40–105 g (95% CI) greater than birds with standard harnesses, and 28–99 g (95% CI) greater than birds with modified harnesses. Further, results of focal behavior observations indicated ducks with transmitters were less likely to be in water than control birds. We also tested whether movements of wild birds marked with a similar Teflon harness satellite transmitter aligned with population movements reported by on-the-ground observers who indexed local abundances of mid-continent mallards throughout the non-breeding period. Results indicated birds marked with satellite transmitters moved concurrently with the larger unmarked population. Our results have broad implications for field research and suggest that investigators should consider potential for physiological and behavioral effects brought about by tracking equipment. Nonetheless, results from wild ducks indicate satellite telemetry has the potential to provide useful movement data.

Development of termination and utilization concepts for flat conductor cables. Volume 2: Utilization of small gage wire round conductor cables

NASA Technical Reports Server (NTRS)

1972-01-01

The practical use of small-gage round wire for electrical wiring in manned air and space vehicle environments is discussed. The investigation consisted on a study of wire construction and candidate wire harness concepts, fabrication of small-gage wire harnesses, and verification of promising configurations by laboratory evaluation. The wire constructions selected for harness fabrication are described. Results of the laboratory evaluation are included.

FOAM-IN-PLACE FORM FITTING HELMET LINERS

DTIC Science & Technology

A urethane foam formulation has been developed to produce foamed-in-place helmet liners for Air Force crash or flying helmets. High density urethane...foam helmet liners has been foamed-in-place directly on the flying crew member’s head, producing a perfectly fitting helmet liner with a minimum of...time, labor and inconvenience. These liners were produced at an extremely modest cost. Design and fabrication of a suitable mold in which the helmet

An experimental apparatus to simulate body-powered prosthetic usage: Development and preliminary evaluation.

PubMed

Gao, Fan; Rodriguez, Johanan; Kapp, Susan

2016-06-01

Harness fitting in the body-powered prosthesis remains more art than science due to a lack of consistent and quantitative evaluation. The aim of this study was to develop a mechanical, human-body-shaped apparatus to simulate body-powered upper limb prosthetic usage and evaluate its capability of quantitative examination of harness configuration. The apparatus was built upon a torso of a wooden mannequin and integrated major mechanical joints to simulate terminal device operation. Sensors were used to register cable tension, cable excursion, and grip force simultaneously. The apparatus allowed the scapula to move up to 127 mm laterally and the load cell can measure the cable tension up to 445 N. Our preliminary evaluation highlighted the needs and importance of investigating harness configurations in a systematic and controllable manner. The apparatus allows objective, systematic, and quantitative evaluation of effects of realistic harness configurations and will provide insightful and working knowledge on harness fitting in upper limb amputees using body-powered prosthesis. © The International Society for Prosthetics and Orthotics 2015.

Vascular labeling of the head and neck vessels: Technique, advantages and limitations.

PubMed

Gálvez, Alba; Caraballo, José-Leonardo; Manzanares-Céspedes, María-Cristina; Valdivia-Gandur, Iván; Figueiredo, Rui; Valmaseda-Castellón, Eduard

2017-05-01

Vascular staining techniques have been used to describe the vascular structures of several anatomic areas. However, few reports have described this procedure in the head and neck region. This paper describes a head and neck vascular labeling procedure, and describes some of the technical complications that may occur. Fifteen specimen cadaver heads were prepared. After drying the vascular system, the internal carotid arteries were ligated and a solution with latex and a gelling agent was injected into the internal carotid arteries and external jugular veins. Two different colors were employed to differentiate arteries from veins. A total of 60ml latex was injected into each blood vessel. Subsequently, the specimens were refrigerated at 5°C for a minimum of 24 hours. Finally, a dissection was performed to identify the venous and arterial systems of the maxillofacial region. In most specimens, correct identification of the vascular structures (lingual artery, pterigoyd plexus, and the major palatal arteries, among others) was possible. However, in three heads a major technical problem occurred (the latex remained liquid), making the dissection unfeasible. Other minor complications such as latex obstruction due to the presence of atheromas were found in two further specimens. The vascular labeling technique is a predictable, effective and simple method for analyzing the vascular system of the maxillofacial area in cadaveric studies, including vessels of reduced diameter or with an intraosseous course. This procedure can be especially useful to teach vascular anatomy to dental students and postgraduate residents. Key words: Blood vessels, vascular casting, vascular labeling, head and neck arteries, carotid arteries, jugular veins.

Optimization Strategies for Bruch's Membrane Opening Minimum Rim Area Calculation: Sequential versus Simultaneous Minimization.

PubMed

Enders, Philip; Adler, Werner; Schaub, Friederike; Hermann, Manuel M; Diestelhorst, Michael; Dietlein, Thomas; Cursiefen, Claus; Heindl, Ludwig M

2017-10-24

To compare a simultaneously optimized continuous minimum rim surface parameter between Bruch's membrane opening (BMO) and the internal limiting membrane to the standard sequential minimization used for calculating the BMO minimum rim area in spectral domain optical coherence tomography (SD-OCT). In this case-control, cross-sectional study, 704 eyes of 445 participants underwent SD-OCT of the optic nerve head (ONH), visual field testing, and clinical examination. Globally and clock-hour sector-wise optimized BMO-based minimum rim area was calculated independently. Outcome parameters included BMO-globally optimized minimum rim area (BMO-gMRA) and sector-wise optimized BMO-minimum rim area (BMO-MRA). BMO area was 1.89 ± 0.05 mm 2 . Mean global BMO-MRA was 0.97 ± 0.34 mm 2 , mean global BMO-gMRA was 1.01 ± 0.36 mm 2 . Both parameters correlated with r = 0.995 (P < 0.001); mean difference was 0.04 mm 2 (P < 0.001). In all sectors, parameters differed by 3.0-4.2%. In receiver operating characteristics, the calculated area under the curve (AUC) to differentiate glaucoma was 0.873 for BMO-MRA, compared to 0.866 for BMO-gMRA (P = 0.004). Among ONH sectors, the temporal inferior location showed the highest AUC. Optimization strategies to calculate BMO-based minimum rim area led to significantly different results. Imposing an additional adjacency constraint within calculation of BMO-MRA does not improve diagnostic power. Global and temporal inferior BMO-MRA performed best in differentiating glaucoma patients.

Shoulder harnesses

DOT National Transportation Integrated Search

1979-06-01

This bibliography represents literature acquired since the establishment of the National Highway Traffic Safety Administration (NHTSA) concerning the development and use of shoulder harnesses in motor vehicles. It is comprised of NHTSA contract repor...

Cushion System for Multi-Use Child Safety Seat

NASA Technical Reports Server (NTRS)

Dabney, Richard W. (Inventor); Elrod, Susan V. (Inventor)

2007-01-01

A cushion system for use with a child safety seat has a plurality of bladders assembled to form a seat cushion that cooperates with the seat's safety harness. One or more sensors coupled to the safety harness sense tension therein and generate a signal indicative of the tension. Each of the bladders is individually pressurized by a pressurization system to define a support configuration of the seat cushion. The pressurization system is disabled when tension in the safety harness has attained a threshold level.

Cushion system for multi-use child safety seat

NASA Technical Reports Server (NTRS)

Elrod, Susan V. (Inventor); Dabney, Richard W. (Inventor)

2007-01-01

A cushion system for use with a child safety seat has a plurality of bladders assembled to form a seat cushion that cooperates with the seat's safety harness. One or more sensors coupled to the safety harness sense tension therein and generate a signal indicative of the tension. Each of the bladders is individually pressurized by a pressurization system to define a support configuration of the seat cushion. The pressurization system is disabled when tension in the safety harness has attained a threshold level.

Advanced air revitalization for optimized crew and plant environments

NASA Technical Reports Server (NTRS)

Lee, M. G.; Grigger, David J.; Brown, Mariann F.

1991-01-01

The Hybrid Air Revitalization System (HARS) closed ecosystem concept presented encompasses electrochemical CO2 and O2 separators, in conjunction with a mechanical condenser/separator for maintaining CO2, O2, and humidity levels in crew and plant habitats at optimal conditions. HARS requires no expendables, and allows flexible process control on the bases of electrochemical cell current, temperature, and airflow rate variations. HARS capacity can be easily increased through the incorporation of additional chemical cells. Detailed system flowcharts are provided.

Harnessing vision for computation.

PubMed

Changizi, Mark

2008-01-01

Might it be possible to harness the visual system to carry out artificial computations, somewhat akin to how DNA has been harnessed to carry out computation? I provide the beginnings of a research programme attempting to do this. In particular, new techniques are described for building 'visual circuits' (or 'visual software') using wire, NOT, OR, and AND gates in a visual 6modality such that our visual system acts as 'visual hardware' computing the circuit, and generating a resultant perception which is the output.

The minimal invasive direct anterior approach in combination with large heads in total hip arthroplasty - is dislocation still a major issue? a case control study.

PubMed

Hoell, Steffen; Sander, Marius; Gosheger, Georg; Ahrens, Helmut; Dieckmann, Ralf; Hauschild, Gregor

2014-03-12

There have been increasing numbers of publications in recent years on minimally invasive surgery (MIS) for total hip arthroplasty (THA), reporting results with the use of different head sizes, tribologic and functional outcomes. This study presents the results and early complication rates after THA using the direct anterior approach (DAA) in combination with head sizes ≥ 36 mm. A total of 113 patients with THA were included in the study. The Harris Hip Score (HHS) was determined, a radiographic evaluation was carried out, and complications were recorded. The minimum follow-up period was 2 years (means 35 ± 7 months). The HHS improved from 43.6 (± 12) to 88.2 (± 14; P < 0.01). One early infection occurred, one periprosthetic fracture, and three cases of aseptic stem loosening. No incorrect positioning of the implants was observed, and there were no dislocations. THA with the minimally invasive DAA in combination with large heads is associated with good to very good functional results in the majority of cases. The complication rates are not increased. The rate of dislocation mainly as an complication of the first two years can be markedly reduced in particular.

Virtual reality-based navigation task to reveal obstacle avoidance performance in individuals with visuospatial neglect.

PubMed

Aravind, Gayatri; Darekar, Anuja; Fung, Joyce; Lamontagne, Anouk

2015-03-01

Persons with post-stroke visuospatial neglect (VSN) often collide with moving obstacles while walking. It is not well understood whether the collisions occur as a result of attentional-perceptual deficits caused by VSN or due to post-stroke locomotor deficits. We assessed individuals with VSN on a seated, joystick-driven obstacle avoidance task, thus eliminating the influence of locomotion. Twelve participants with VSN were tested on obstacle detection and obstacle avoidance tasks in a virtual environment that included three obstacles approaching head-on or 30 (°) contralesionally/ipsilesionally. Our results indicate that in the detection task, the contralesional and head-on obstacles were detected at closer proximities compared to the ipsilesional obstacle. For the avoidance task collisions were observed only for the contralesional and head-on obstacle approaches. For the contralesional obstacle approach, participants initiated their avoidance strategies at smaller distances from the obstacle and maintained smaller minimum distances from the obstacles. The distance at detection showed a negative association with the distance at the onset of avoidance strategy for all three obstacle approaches. We conclusion the observation of collisions with contralesional and head-on obstacles, in the absence of locomotor burden, provides evidence that attentional-perceptual deficits due to VSN, independent of post-stroke locomotor deficits, alter obstacle avoidance abilities.

Multilevel groundwater monitoring of hydraulic head and temperature in the eastern Snake River Plain aquifer, Idaho National Laboratory, Idaho, 2007-08

USGS Publications Warehouse

Fisher, Jason C.; Twining, Brian V.

2011-01-01

During 2007 and 2008, the U.S. Geological Survey, in cooperation with the U.S. Department of Energy, collected quarterly depth-discrete measurements of fluid pressure and temperature in six boreholes located in the eastern Snake River Plain aquifer of Idaho. Each borehole was instrumented with a multilevel monitoring system consisting of a series of valved measurement ports, packer bladders, casing segments, and couplers. Hydraulic heads (head) and water temperatures in boreholes were monitored at 86 hydraulically-isolated depth intervals located 448.0 to 1,377.6 feet below land surface. The calculation of head is most sensitive to fluid pressure and the altitude of the pressure transducer at each port coupling; it is least sensitive to barometric pressure and water temperature. An analysis of errors associated with the head calculation determined the accuracy of an individual head measurement at +/- 2.3 feet. Many of the sources of measurement error are diminished when considering the differences between two closely-spaced readings of head; therefore, a +/- 0.1 foot measurement accuracy was assumed for vertical head differences (and gradients) calculated between adjacent monitoring zones. Vertical head and temperature profiles were unique to each borehole, and were characteristic of the heterogeneity and anisotropy of the eastern Snake River Plain aquifer. The vertical hydraulic gradients in each borehole remained relatively constant over time with minimum Pearson correlation coefficients between head profiles ranging from 0.72 at borehole USGS 103 to 1.00 at boreholes USGS 133 and MIDDLE 2051. Major inflections in the head profiles almost always coincided with low permeability sediment layers. The presence of a sediment layer, however, was insufficient for identifying the location of a major head change in a borehole. The vertical hydraulic gradients were defined for the major inflections in the head profiles and were as much as 2.2 feet per foot. Head gradients generally were downward in boreholes USGS 133, 134, and MIDDLE 2050A, zero in boreholes USGS 103 and 132, and exhibited a reversal in direction in borehole MIDDLE 2051. Water temperatures in all boreholes ranged from 10.2 to 16.3 degrees Celsius. Boreholes USGS 103 and 132 are in an area of concentrated volcanic vents and fissures, and measurements show water temperature decreasing with depth. All other measurements in boreholes show water temperature increasing with depth. A comparison among boreholes of the normalized mean head over time indicates a moderately positive correlation.

e-Justice Implementation at a National Scale: The Ugandan Case

NASA Astrophysics Data System (ADS)

Kitoogo, Fredrick Edward; Bitwayiki, Constantine

The use of information and communications technologies has been identified as one of the means suitable for supplementing the various reforms in convalescing the performance of the justice sector. The Government of Uganda has made strides in the implementation of e-Government to effectively utilize information and communications technologies in governance. The justice players are manifested in a justice, law and order sector which is based on the the Sector Wide Approach whose basic principle is that communication, cooperation and coordination between institutions can greatly add value to service delivery within a sector. Although a subset of e-Government, e-Justice aims at improving service delivery and collaboration between all justice players through the use of ICTs and needs to be spear-headed at a sector level. This work proposes ways of harnessing the existing opportunities and methods to implement e-Justice in Uganda that will culminate into a generic framework that can be applied in similar countries.

A Simple Two Aircraft Conflict Resolution Algorithm

NASA Technical Reports Server (NTRS)

Chatterji, Gano B.

1999-01-01

Conflict detection and resolution methods are crucial for distributed air-ground traffic management in which the crew in the cockpit, dispatchers in operation control centers and air traffic controllers in the ground-based air traffic management facilities share information and participate in the traffic flow and traffic control imctions.This paper describes a conflict detection and a conflict resolution method. The conflict detection method predicts the minimum separation and the time-to-go to the closest point of approach by assuming that both the aircraft will continue to fly at their current speeds along their current headings. The conflict resolution method described here is motivated by the proportional navigation algorithm. It generates speed and heading commands to rotate the line-of-sight either clockwise or counter-clockwise for conflict resolution. Once the aircraft achieve a positive range-rate and no further conflict is predicted, the algorithm generates heading commands to turn back the aircraft to their nominal trajectories. The speed commands are set to the optimal pre-resolution speeds. Six numerical examples are presented to demonstrate the conflict detection and resolution method.

Electrostatically Biased Binding of Kinesin to Microtubules

PubMed Central

Zheng, Wenjun; Alonso, Maria; Huber, Gary; Dlugosz, Maciej; McCammon, J. Andrew; Cross, Robert A.

2011-01-01

The minimum motor domain of kinesin-1 is a single head. Recent evidence suggests that such minimal motor domains generate force by a biased binding mechanism, in which they preferentially select binding sites on the microtubule that lie ahead in the progress direction of the motor. A specific molecular mechanism for biased binding has, however, so far been lacking. Here we use atomistic Brownian dynamics simulations combined with experimental mutagenesis to show that incoming kinesin heads undergo electrostatically guided diffusion-to-capture by microtubules, and that this produces directionally biased binding. Kinesin-1 heads are initially rotated by the electrostatic field so that their tubulin-binding sites face inwards, and then steered towards a plus-endwards binding site. In tethered kinesin dimers, this bias is amplified. A 3-residue sequence (RAK) in kinesin helix alpha-6 is predicted to be important for electrostatic guidance. Real-world mutagenesis of this sequence powerfully influences kinesin-driven microtubule sliding, with one mutant producing a 5-fold acceleration over wild type. We conclude that electrostatic interactions play an important role in the kinesin stepping mechanism, by biasing the diffusional association of kinesin with microtubules. PMID:22140358

The trans-Himalayan flights of bar-headed geese (Anser indicus)

USGS Publications Warehouse

Hawkes, L.A.; Balachandran, S.; Batbayar, N.; Butler, P.J.; Frappell, P.B.; Milsom, W.K.; Tseveenmyadag, N.; Newman, S.H.; Scott, G.R.; Sathiyaselvam, P.; Takekawa, John Y.; Wikelski, M.; Bishop, C.M.

2011-01-01

Birds that fly over mountain barriers must be capable of meeting the increased energetic cost of climbing in low-density air, even though less oxygen may be available to support their metabolism. This challenge is magnified by the reduction in maximum sustained climbing rates in large birds. Bar-headed geese (Anser indicus) make one of the highest and most iconic transmountain migrations in the world. We show that those populations of geese that winter at sea level in India are capable of passing over the Himalayas in 1 d, typically climbing between 4,000 and 6,000min 7-8 h. Surprisingly, these birds do not rely on the assistance of upslope tailwinds that usually occur during the day and can support minimum climb rates of 0.8-2.2 km??h-1, even in the relative stillness of the night. They appear to strategically avoid higher speed winds during the afternoon, thus maximizing safety and control during flight. It would seem, therefore, that bar-headed geese are capable of sustained climbing flight over the passes of the Himalaya under their own aerobic power.

Improving highway advisory radio predictability and performance

DOT National Transportation Integrated Search

2011-01-01

Highway Advisory Radio (HAR) stations, sometimes referred to as Travelers Information Stations (TIS), : allow highway agencies to broadcast important messages about traffic, weather and roadway conditions to : motorists. Caltrans has deployed HAR ...

14 CFR 91.521 - Shoulder harness.

Code of Federal Regulations, 2010 CFR

2010-01-01

... inertia load factors established under the certification basis of the airplane. (b) No person may operate... used; and (2) Safety belt and shoulder harness restraint systems may be designed to the inertia load...

14 CFR 91.521 - Shoulder harness.

Code of Federal Regulations, 2013 CFR

2013-01-01

... inertia load factors established under the certification basis of the airplane. (b) No person may operate... used; and (2) Safety belt and shoulder harness restraint systems may be designed to the inertia load...

14 CFR 91.521 - Shoulder harness.

Code of Federal Regulations, 2014 CFR

2014-01-01

... inertia load factors established under the certification basis of the airplane. (b) No person may operate... used; and (2) Safety belt and shoulder harness restraint systems may be designed to the inertia load...

14 CFR 91.521 - Shoulder harness.

Code of Federal Regulations, 2011 CFR

2011-01-01

... inertia load factors established under the certification basis of the airplane. (b) No person may operate... used; and (2) Safety belt and shoulder harness restraint systems may be designed to the inertia load...

14 CFR 91.521 - Shoulder harness.

Code of Federal Regulations, 2012 CFR

2012-01-01

... inertia load factors established under the certification basis of the airplane. (b) No person may operate... used; and (2) Safety belt and shoulder harness restraint systems may be designed to the inertia load...

Head and pelvic movement asymmetry during lungeing in horses with symmetrical movement on the straight.

PubMed

Rhodin, M; Roepstorff, L; French, A; Keegan, K G; Pfau, T; Egenvall, A

2016-05-01

Lungeing is commonly used as part of standard lameness examinations in horses. Knowledge of how lungeing influences motion symmetry in sound horses is needed. The aim of this study was to objectively evaluate the symmetry of vertical head and pelvic motion during lungeing in a large number of horses with symmetric motion during straight line evaluation. Cross-sectional prospective study. A pool of 201 riding horses, all functioning well and considered sound by their owners, were evaluated in trot on a straight line and during lungeing to the left and right. From this pool, horses with symmetric vertical head and pelvic movement during the straight line trot (n = 94) were retained for analysis. Vertical head and pelvic movements were measured with body mounted uniaxial accelerometers. Differences between vertical maximum and minimum head (HDmax, HDmin) and pelvic (PDmax, PDmin) heights between left and right forelimb and hindlimb stances were compared between straight line trot and lungeing in either direction. Vertical head and pelvic movements during lungeing were more asymmetric than during trot on a straight line. Common asymmetric patterns seen in the head were more upward movement during push-off of the outside forelimb and less downward movement during impact of the inside limb. Common asymmetric patterns seen in the pelvis were less upward movement during push-off of the outside hindlimb and less downward movement of the pelvis during impact of the inside hindlimb. Asymmetric patterns in one lunge direction were frequently not the same as in the opposite direction. Lungeing induces systematic asymmetries in vertical head and pelvic motion patterns in horses that may not be the same in both directions. These asymmetries may mask or mimic fore- or hindlimb lameness. © 2015 The Authors. Equine Veterinary Journal published by John Wiley & Sons Ltd on behalf of EVJ Ltd.

A new fast algorithm for solving the minimum spanning tree problem based on DNA molecules computation.

PubMed

Wang, Zhaocai; Huang, Dongmei; Meng, Huajun; Tang, Chengpei

2013-10-01

The minimum spanning tree (MST) problem is to find minimum edge connected subsets containing all the vertex of a given undirected graph. It is a vitally important NP-complete problem in graph theory and applied mathematics, having numerous real life applications. Moreover in previous studies, DNA molecular operations usually were used to solve NP-complete head-to-tail path search problems, rarely for NP-hard problems with multi-lateral path solutions result, such as the minimum spanning tree problem. In this paper, we present a new fast DNA algorithm for solving the MST problem using DNA molecular operations. For an undirected graph with n vertex and m edges, we reasonably design flexible length DNA strands representing the vertex and edges, take appropriate steps and get the solutions of the MST problem in proper length range and O(3m+n) time complexity. We extend the application of DNA molecular operations and simultaneity simplify the complexity of the computation. Results of computer simulative experiments show that the proposed method updates some of the best known values with very short time and that the proposed method provides a better performance with solution accuracy over existing algorithms. Copyright © 2013 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

Effects of tidal current phase at the junction of two straits

USGS Publications Warehouse

Warner, J.; Schoellhamer, D.; Burau, J.; Schladow, G.

2002-01-01

Estuaries typically have a monotonic increase in salinity from freshwater at the head of the estuary to ocean water at the mouth, creating a consistent direction for the longitudinal baroclinic pressure gradient. However, Mare Island Strait in San Francisco Bay has a local salinity minimum created by the phasing of the currents at the junction of Mare Island and Carquinez Straits. The salinity minimum creates converging baroclinic pressure gradients in Mare Island Strait. Equipment was deployed at four stations in the straits for 6 months from September 1997 to March 1998 to measure tidal variability of velocity, conductivity, temperature, depth, and suspended sediment concentration. Analysis of the measured time series shows that on a tidal time scale in Mare Island Strait, the landward and seaward baroclinic pressure gradients in the local salinity minimum interact with the barotropic gradient, creating regions of enhanced shear in the water column during the flood and reduced shear during the ebb. On a tidally averaged time scale, baroclinic pressure gradients converge on the tidally averaged salinity minimum and drive a converging near-bed and diverging surface current circulation pattern, forming a "baroclinic convergence zone" in Mare Island Strait. Historically large sedimentation rates in this area are attributed to the convergence zone. 

14 CFR 91.1035 - Passenger awareness.

Code of Federal Regulations, 2013 CFR

2013-01-01

...) Use of safety belts, shoulder harnesses, and child restraint systems: Each passenger must be briefed... installed, his or her shoulder harness fastened about him or her, and if a child is being transported, the...

14 CFR 91.1035 - Passenger awareness.

Code of Federal Regulations, 2010 CFR

2010-01-01

...) Use of safety belts, shoulder harnesses, and child restraint systems: Each passenger must be briefed... installed, his or her shoulder harness fastened about him or her, and if a child is being transported, the...

14 CFR 91.1035 - Passenger awareness.

Code of Federal Regulations, 2012 CFR

2012-01-01

...) Use of safety belts, shoulder harnesses, and child restraint systems: Each passenger must be briefed... installed, his or her shoulder harness fastened about him or her, and if a child is being transported, the...

14 CFR 91.1035 - Passenger awareness.

Code of Federal Regulations, 2014 CFR

2014-01-01

...) Use of safety belts, shoulder harnesses, and child restraint systems: Each passenger must be briefed... installed, his or her shoulder harness fastened about him or her, and if a child is being transported, the...

Colloidal and antibacterial properties of novel triple-headed, double-tailed amphiphiles: exploring structure-activity relationships and synergistic mixtures.

PubMed

Marafino, John N; Gallagher, Tara M; Barragan, Jhosdyn; Volkers, Brandi L; LaDow, Jade E; Bonifer, Kyle; Fitzgerald, Gabriel; Floyd, Jason L; McKenna, Kristin; Minahan, Nicholas T; Walsh, Brenna; Seifert, Kyle; Caran, Kevin L

2015-07-01

Two novel series of tris-cationic, tripled-headed, double-tailed amphiphiles were synthesized and the effects of tail length and head group composition on the critical aggregation concentration (CAC), thermodynamic parameters, and minimum inhibitory concentration (MIC) against six bacterial strains were investigated. Synergistic antibacterial combinations of these amphiphiles were also identified. Amphiphiles in this study are composed of a benzene core with three benzylic ammonium bromide groups, two of which have alkyl chains, each 8-16 carbons in length. The third head group is a trimethylammonium or pyridinium. Log of critical aggregation concentration (log[CAC]) and heat of aggregation (ΔHagg) were both inversely proportional to the length of the linear hydrocarbon chains. Antibacterial activity increases with tail length until an optimal tail length of 12 carbons per chain, above which, activity decreased. The derivatives with two 12 carbon chains had the best antibacterial activity, killing all tested strains at concentrations of 1-2μM for Gram-positive and 4-16μM for Gram-negative bacteria. The identity of the third head group (trimethylammonium or pyridinium) had minimal effect on colloidal and antibacterial activity. The antibacterial activity of several binary combinations of amphiphiles from this study was higher than activity of individual amphiphiles, indicating that these combinations are synergistic. These amphiphiles show promise as novel antibacterial agents that could be used in a variety of applications. Copyright © 2015 Elsevier Ltd. All rights reserved.

Human Activity Recognition Supported on Indoor Localization: A Systematic Review.

PubMed

Cerón, Jesús; López, Diego M

2018-01-01

The number of older adults is growing worldwide. This has a social and economic impact in all countries because of the increased number of older adults affected by chronic diseases, health emergencies, and disabilities, representing at the end high cost for the health system. To face this problem, the Ambient Assisted Living (AAL) domain has emerged. Its main objective is to extend the time that older adults can live independently in their homes. AAL is supported by different fields and technologies, being Human Activity Recognition (HAR), control of vital signs and location tracking the three of most interest during the last years. To perform a systematic review about Human Activity Recognition (HAR) approaches supported on Indoor Localization (IL) and vice versa, describing the methods they have used, the accuracy they have obtained and whether they have been directed towards the AAL domain or not. A systematic review of six databases was carried out (ACM, IEEE Xplore, PubMed, Science Direct and Springer). 27 papers were found. They were categorised into three groups according their approach: paper focus on 1. HAR, 2. IL, 3. HAR and IL. A detailed analysis of the following factors was performed: type of methods and technologies used for HAR, IL and data fusion, as well as the precision obtained for them. This systematic review shows that the relationship between HAR and IL has been very little studied, therefore providing insights of its potential mutual support to provide AAL solutions.

Accelerated hematopoietic syndrome after radiation doses bridging hematopoietic (H-ARS) and gastrointestinal (GI-ARS) acute radiation syndrome: early hematological changes and systemic inflammatory response syndrome in minipig.

PubMed

Moroni, Maria; Elliott, Thomas B; Deutz, Nicolaas E; Olsen, Cara H; Owens, Rossitsa; Christensen, Christine; Lombardini, Eric D; Whitnall, Mark H

2014-05-01

To characterize acute radiation syndrome (ARS) sequelae at doses intermediate between the bone marrow (H-ARS) and full gastrointestinal (GI-ARS) syndrome. Male minipigs, approximately 5 months old, 9-12 kg in weight, were irradiated with Cobalt-60 (total body, bilateral gamma irradiation, 0.6 Gy/min). Endpoints were 10-day survival, gastrointestinal histology, plasma citrulline, bacterial translocation, vomiting, diarrhea, vital signs, systemic inflammatory response syndrome (SIRS), febrile neutropenia (FN). We exposed animals to doses (2.2-5.0 Gy) above those causing H-ARS (1.6-2.0 Gy), and evaluated development of ARS. Compared to what was observed during H-ARS (historical data: Moroni et al. 2011a , 2011c ), doses above 2 Gy produced signs of increasingly severe pulmonary damage, faster deterioration of clinical conditions, and faster increases in levels of C-reactive protein (CRP). In the range of 4.6-5.0 Gy, animals died by day 9-10; signs of the classic GI syndrome, as measured by diarrhea, vomiting and bacterial translocation, did not occur. At doses above 2 Gy we observed transient reduction in circulating citrulline levels, and animals exhibited earlier depletion of blood elements and faster onset of SIRS and FN. An accelerated hematopoietic subsyndrome (AH-ARS) is observed at radiation doses between those producing H-ARS and GI-ARS. It is characterized by early onset of SIRS and FN, and greater lung damage, compared to H-ARS.

Efficient micromagnetics for magnetic storage devices

NASA Astrophysics Data System (ADS)

Escobar Acevedo, Marco Antonio

Micromagnetics is an important component for advancing the magnetic nanostructures understanding and design. Numerous existing and prospective magnetic devices rely on micromagnetic analysis, these include hard disk drives, magnetic sensors, memories, microwave generators, and magnetic logic. The ability to examine, describe, and predict the magnetic behavior, and macroscopic properties of nanoscale magnetic systems is essential for improving the existing devices, for progressing in their understanding, and for enabling new technologies. This dissertation describes efficient micromagnetic methods as required for magnetic storage analysis. Their performance and accuracy is demonstrated by studying realistic, complex, and relevant micromagnetic system case studies. An efficient methodology for dynamic micromagnetics in large scale simulations is used to study the writing process in a full scale model of a magnetic write head. An efficient scheme, tailored for micromagnetics, to find the minimum energy state on a magnetic system is presented. This scheme can be used to calculate hysteresis loops. An efficient scheme, tailored for micromagnetics, to find the minimum energy path between two stable states on a magnetic system is presented. This minimum energy path is intimately related to the thermal stability.

Laterally structured ripple and square phases with one and two dimensional thickness modulations in a model bilayer system.

PubMed

Debnath, Ananya; Thakkar, Foram M; Maiti, Prabal K; Kumaran, V; Ayappa, K G

2014-10-14

Molecular dynamics simulations of bilayers in a surfactant/co-surfactant/water system with explicit solvent molecules show formation of topologically distinct gel phases depending upon the bilayer composition. At low temperatures, the bilayers transform from the tilted gel phase, Lβ', to the one dimensional (1D) rippled, Pβ' phase as the surfactant concentration is increased. More interestingly, we observe a two dimensional (2D) square phase at higher surfactant concentration which, upon heating, transforms to the gel Lβ' phase. The thickness modulations in the 1D rippled and square phases are asymmetric in two surfactant leaflets and the bilayer thickness varies by a factor of ∼2 between maximum and minimum. The 1D ripple consists of a thinner interdigitated region of smaller extent alternating with a thicker non-interdigitated region. The 2D ripple phase is made up of two superimposed square lattices of maximum and minimum thicknesses with molecules of high tilt forming a square lattice translated from the lattice formed with the thickness minima. Using Voronoi diagrams we analyze the intricate interplay between the area-per-head-group, height modulations and chain tilt for the different ripple symmetries. Our simulations indicate that composition plays an important role in controlling the formation of low temperature gel phase symmetries and rippling accommodates the increased area-per-head-group of the surfactant molecules.

Antibacterial Activity of Anthraquinone from Aloe on Spiced Pig Head

NASA Astrophysics Data System (ADS)

Xu, Lingyi; Li, Xiao; Cui, Yuqian; Pang, Meixia; Wang, Fang; Qi, Jinghua

2017-12-01

[Objective] To optimize the extraction of anthraquinone from Aloe by ultrasonic extraction and its antibacterialactivity. [Method]The influences of different extraction time and ethanol concentration, on anthraquinone contentwere evaluated by asingle factor experiment. And anthraquinone content was determined by ultraviolet spectrophotometry. The bacteriostasis of anthraquinone on spiced pig head’s common putrefying bacteria: Staphylococcus, Serratieae, Bacillus, Proteus and the minimal inhibitory concentration (MIC) were studied by oxford plate assay system. [Result]The best extraction time was 30 minutes and the best ethanol concentration was 80%. The antibacterial activity of the Aloe anthraquinone on Staphylococcus Aureus, Bacillus Proteus is obviously, the minimum inhibitory concentrations were 0.0625 g/mL, 0.05 g/mL, 0.125 g/mL respectively and no inhibitory effect on Serratieae. [Conclusions] The anthraquinones from Aloe can inhibit a part Of spoilage bacteria inspiced pig heads.

Feasibility study of a 270V dc flat cable aircraft electrical power distributed system

NASA Astrophysics Data System (ADS)

Musga, M. J.; Rinehart, R. J.

1982-01-01

This report documents the efforts of a one man-year feasibility study to evaluate the usage of flat conductors in place of conventional round wires for a 270 volt direct current aircraft power distribution system. This study consisted of designing electrically equivalent power distribution harnesses in flat conductor configurations for a currently operational military aircraft. Harness designs were established for installation in aircraft airframes which are: (1) All metal, or (2) All composite, or (3) a mixture of both. Flat cables have greater surface areas for heat transfer allowing higher current densities and therefore lighter weight conductors, than with round wires. Flat cables are less susceptible to electromagnetic effects. However, these positive factors are partially offset by installation and maintenance difficulties. This study concludes that the extent of these difficulties can be adequately limited with appropriate modification to present installation and maintenance practices. A comparative analysis of the flat and the round conductor power distribution harnesses was made for weight, cost, maintenance and reliability. The knowledge gained from the design and comparative analysis phases was used to generate design criteria for flat power cable harnesses and to identify and prioritize flat cable harness components and associated production tooling which require development.

A Cell-targeted Photodynamic Nanomedicine Strategy for Head & Neck Cancers

PubMed Central

Master, Alyssa; Malamas, Anthony; Solanki, Rachna; Clausen, Dana M.; Eiseman, Julie L.; Gupta, Anirban Sen

2013-01-01

Photodynamic Therapy (PDT) holds great promise for the treatment of head and neck (H&N) carcinomas where repeated loco-regional therapy often becomes necessary due to the highly aggressive and recurrent nature of the cancers. While interstitial light delivery technologies are being refined for PDT of H&N and other cancers, a parallel clinically relevant research area is the formulation of photosensitizers in nanovehicles that allow systemic administration yet preferential enhanced uptake in the tumor. This approach can render dual-selectivity of PDT, by harnessing both the drug and the light delivery within the tumor. To this end, we report on a cell-targeted nanomedicine approach for the photosensitizer silicon phthalocyanine-4 (Pc 4), by packaging it within polymeric micelles that are surface-decorated with GE11-peptides to promote enhanced cell-selective binding and receptor-mediated internalization in EGFR-overexpressing H&N cancer cells. Using fluorescence spectroscopy and confocal microscopy, we demonstrate in vitro that the EGFR-targeted Pc 4-nanoformulation undergoes faster and higher uptake in EGFR-overexpressing H&N SCC-15 cells. We further demonstrate that this enhanced Pc 4 uptake results in significant cell-killing and drastically reduced post-PDT clonogenicity. Building on this in vitro data, we demonstrate that the EGFR-targeted Pc 4-nanoformulation results in significant intra-tumoral drug uptake and subsequent enhanced PDT response, in vivo, in SCC-15 xenografts in mice. Altogether our results show significant promise towards a cell-targeted photodynamic nanomedicine for effective treatment of H&N carcinomas. PMID:23531079

Highway Advisory Radio Message Development Guide, Final Report

DOT National Transportation Integrated Search

1982-10-01

HIGHWAY ADVISORY RADIO (HAR) PROVIDES TRAFFIC OPERATING AGENCIES WITH THE CAPABILITY TO COMMUNICATE TRAFFIC AND TRAVEL RELATED INFORMATION TO MOTORISTS USING THE VEHICLE'S AM RADIO RECEIVER. THIS REPORT PRESENTS RECOMMENDED HAR MESSAGE DEVELOPMENT PR...

HARNESS END OF ELECTRIC TURBINE IN LOWER LEVEL OF HYDROELECTRIC ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

HARNESS END OF ELECTRIC TURBINE IN LOWER LEVEL OF HYDROELECTRIC POWER HOUSE - St. Lucie Canal, Lock No. 1, Hydroelectric Power House, St. Lucie, Cross State Canal, Okeechobee Intracoastal Waterway, Stuart, Martin County, FL

Subject Load-Harness Interaction During Zero-Gravity Treadmill Exercise

NASA Technical Reports Server (NTRS)

McCrory, Jean L.; Baron, Heidi A.; Derr, Janice A.; Davis, Brian L.; Cavanagh, Peter R.

1996-01-01

When astronauts exercise on orbit, a subject load device (SLD) must be used to return the subject back to the supporting surface. The load in the SLD needs to be transferred the body by a harness which typically distributes this load between the pelvis and We shoulders. Through the use of a zero-gravity simulator, this research compared subject comfort and ground reaction forces during treadmill running at three levels of subject load (60%,80%, and 100% of body weight) in two harness designs ("shoulder only" and "waist "and shoulder ").

Flat conductor cable design, manufacture, and installation

NASA Technical Reports Server (NTRS)

Angele, W.; Hankins, J. D.

1973-01-01

Pertinent information for hardware selection, design, manufacture, and quality control necessary for flat conductor cable interconnecting harness application is presented. Comparisons are made between round wire cable and flat conductor cable. The flat conductor cable interconnecting harness systems show major cost, weight, and space savings, plus increased system performance and reliability. The design application section includes electrical characteristics, harness design and development, and a full treatise on EMC considerations. Manufacturing and quality control sections pertain primarily to the developed conductor-contact connector system and special flat conductor cable to round wire cable transitions.

Locomotion in simulated microgravity: gravity replacement loads

NASA Technical Reports Server (NTRS)

McCrory, Jean L.; Baron, Heidi A.; Balkin, Sandy; Cavanagh, Peter R.

2002-01-01

BACKGROUND: When an astronaut walks or runs on a treadmill in microgravity, a subject load device (SLD) is used to return him or her back to the treadmill belt. The gravity replacement load (GRL) in the SLD is transferred, via a harness, to the pelvis and/or the shoulders. This research compared comfort and ground reaction forces during treadmill running in a microgravity locomotion simulator at GRLs of 60%, 80%, and 100% of body weight (BW). Two harness designs (shoulder springs only (SSO) and waist and shoulder springs (WSS)) were used. HYPOTHESES: 1) The 100% BW gravity replacement load conditions would be comfortably tolerated and would result in larger ground reaction forces and loading rates than the lower load conditions, and 2) the WSS harness would be more comfortable than the SSO harness. METHODS: Using the Penn State Zero Gravity Locomotion Simulator (ZLS), 8 subjects ran at 2.0 m x s(-1) (4.5 mph) for 3 min at each GRL setting in each harness. Subjective ratings of harness comfort, ground reaction forces, and GRL data were collected during the final minute of exercise. RESULTS: The 100% BW loading conditions were comfortably tolerated (2.3 on a scale of 0-10), although discomfort increased as the GRL increased. There were no overall differences in perceived comfort between the two harnesses. The loading rates (27.1, 33.8, 39.1 BW x s(-1)) and the magnitudes of the first (1.0, 1.4, 1.6 BW) and second (1.3, 1.7, 1.9 BW) peaks of the ground reaction force increased with increasing levels (60, 80, 100% BW respectively) of GRL. CONCLUSIONS: Subjects were able to tolerate a GRL of 100% BW well. The magnitude of the ground reaction force peaks and the loading rate is directly related to the magnitude of the GRL.

Unshrouded Centrifugal Turbopump Impeller Design Methodology

NASA Technical Reports Server (NTRS)

Prueger, George H.; Williams, Morgan; Chen, Wei-Chung; Paris, John; Williams, Robert; Stewart, Eric

2001-01-01

Turbopump weight continues to be a dominant parameter in the trade space for reduction of engine weight. Space Shuttle Main Engine weight distribution indicates that the turbomachinery make up approximately 30% of the total engine weight. Weight reduction can be achieved through the reduction of envelope of the turbopump. Reduction in envelope relates to an increase in turbopump speed and an increase in impeller head coefficient. Speed can be increased until suction performance limits are achieved on the pump or due to alternate constraints the turbine or bearings limit speed. Once the speed of the turbopump is set the impeller tip speed sets the minimum head coefficient of the machine. To reduce impeller diameter the head coefficient must be increased. A significant limitation with increasing head coefficient is that the slope of the head-flow characteristic is affected and this can limit engine throttling range. Unshrouded impellers offer a design option for increased turbopump speed without increasing the impeller head coefficient. However, there are several issues with regard to using an unshrouded impeller: there is a pump performance penalty due to the front open face recirculation flow, there is a potential pump axial thrust problem from the unbalanced front open face and the back shroud face, and since test data is very limited for this configuration, there is uncertainty in the magnitude and phase of the rotordynamic forces due to the front impeller passage. The purpose of the paper is to discuss the design of an unshrouded impeller and to examine the hydrodynamic performance, axial thrust, and rotordynamic performance. The design methodology will also be discussed. This work will help provide some guidelines for unshrouded impeller design.

Zero-g simulation system for therapeutic application

NASA Technical Reports Server (NTRS)

Dane, D. H.

1971-01-01

System aids in therapeutic retraining of damaged muscles or functions as walking support during therapy. Articulated harness assembly contains patient, suspension system supports harness assembly in such a way as to counterbalance exertion of external forces on patient.

Summary of the CTS Transient Event Counter data after one year of operation. [Communication Technology Satellite

NASA Technical Reports Server (NTRS)

Stevens, N. J.; Klinect, V. W.; Gore, J. V.

1977-01-01

The environmental charging of satellite surfaces during geomagnetic substorms is the apparent cause of a significant number of anomalous events occurring on geosynchronous satellites since the early 1970's. Electromagnetic pulses produced in connection with the differential charging of insulators can couple into the spacecraft harness and cause electronic switching anomalies. An investigation conducted to determine the response of the spacecraft surfaces to substorm particle fluxes makes use of a harness transient detector. The harness transient detector, called the Transient Event Counter (TEC) was built and integrated into the Canadian-American Communications Technology Satellite (CTS). A description of the TEC and its operational characteristics is given and the obtained data are discussed. The data show that the satellite surfaces appear to be charged to the point that discharges occur and that the discharge-induced transients couple into the wire harnesses.

Design Process Improvement for Electric CAR Harness

NASA Astrophysics Data System (ADS)

Sawatdee, Thiwarat; Chutima, Parames

2017-06-01

In an automobile parts design company, the customer satisfaction is one of the most important factors for product design. Therefore, the company employs all means to focus its product design process based on the various requirements of customers resulting in high number of design changes. The objective of this research is to improve the design process of the electric car harness that effects the production scheduling by using Fault Tree Analysis (FTA) and Failure Mode and Effect Analysis (FMEA) as the main tools. FTA is employed for root cause analysis and FMEA is used to ranking a High Risk Priority Number (RPN) which is shows the priority of factors in the electric car harness that have high impact to the design of the electric car harness. After the implementation, the improvements are realized significantly since the number of design change is reduced from 0.26% to 0.08%.

Simulated weightlessness - Effects on bioenergetic balance

NASA Technical Reports Server (NTRS)

Jordan, J. P.; Sykes, H. A.; Crownover, J. C.; Schatte, C. L.; Simmons, J. B., II; Jordan, D. P.

1980-01-01

As a prelude to a flight experiment, an attempt was made to separate energy requirements associated with gravity from all other metabolic needs. The biological effects of weightlessness were simulated by suspending animals in a harness so that antigravity muscles were not supporting the body. Twelve pairs of rats were allowed to adapt to wearing a harness for 5 d. Experimental animals were then suspended in harness for 7 d followed by recovery for 7 d. Control animals were harnessed but never suspended. Oxygen consumption, carbon dioxide production and rate of (C-14)O2 expiration from radio-labeled glucose were monitored on selected days. Food intake and body mass were recorded daily. Metabolic rate decreased in experimental animals during 7 d of suspension and returned to normal during recovery. Although some of the metabolic changes may have related to variation in food intake, simulated weightlessness appears to directly affect bioenergetic balance.

Safety harness

DOEpatents

Gunter, Larry W.

1993-01-01

A safety harness to be worn by a worker, especially a worker wearing a plastic suit thereunder for protection in a radioactive or chemically hostile environment, which safety harness comprises a torso surrounding portion with at least one horizontal strap for adjustably securing the harness about the torso, two vertical shoulder straps with rings just forward of the of the peak of the shoulders for attaching a life-line and a pair of adjustable leg supporting straps releasibly attachable to the torso surrounding portion. In the event of a fall, the weight of the worker, when his fall is broken and he is suspended from the rings with his body angled slightly back and chest up, will be borne by the portion of the leg straps behind his buttocks rather than between his legs. Furthermore, the supporting straps do not restrict the air supplied through hoses into his suit when so suspended.

Preliminary report on the CTS transient event counter performance through the 1976 spring eclipse season

NASA Technical Reports Server (NTRS)

Stevens, N. J.; Levell, R. R.; Klinect, V. W.

1976-01-01

The transient event counter (TEC), senses and counts transients having a voltage rise of greater than five volts in three separate wire harnesses: the attitude control harness, the solar array instrumentation harness and the solar array power harness. The operational characteristics of TEC are defined and the preliminary results obtained through the first 90 days of operation including the spring 1976 eclipse season are presented. The results show that the Communications Technology Satellite was charged to the point where discharges occurred. The discharge induced transients did not cause any anomalous events in spacecraft operation. The data indicate that discharges can occur at any time during the day without preference to any local time quadrant. The number of discharges occurring in the one second sample interval are greater than anticipated. The compilation and review of the data is continuing.

Evaluation of a smartphone human activity recognition application with able-bodied and stroke participants.

PubMed

Capela, N A; Lemaire, E D; Baddour, N; Rudolf, M; Goljar, N; Burger, H

2016-01-20

Mobile health monitoring using wearable sensors is a growing area of interest. As the world's population ages and locomotor capabilities decrease, the ability to report on a person's mobility activities outside a hospital setting becomes a valuable tool for clinical decision-making and evaluating healthcare interventions. Smartphones are omnipresent in society and offer convenient and suitable sensors for mobility monitoring applications. To enhance our understanding of human activity recognition (HAR) system performance for able-bodied and populations with gait deviations, this research evaluated a custom smartphone-based HAR classifier on fifteen able-bodied participants and fifteen participants who suffered a stroke. Participants performed a consecutive series of mobility tasks and daily living activities while wearing a BlackBerry Z10 smartphone on their waist to collect accelerometer and gyroscope data. Five features were derived from the sensor data and used to classify participant activities (decision tree). Sensitivity, specificity and F-scores were calculated to evaluate HAR classifier performance. The classifier performed well for both populations when differentiating mobile from immobile states (F-score > 94 %). As activity recognition complexity increased, HAR system sensitivity and specificity decreased for the stroke population, particularly when using information derived from participant posture to make classification decisions. Human activity recognition using a smartphone based system can be accomplished for both able-bodied and stroke populations; however, an increase in activity classification complexity leads to a decrease in HAR performance with a stroke population. The study results can be used to guide smartphone HAR system development for populations with differing movement characteristics.

Earth Observations taken by the Expedition 13 crew

NASA Image and Video Library

2006-09-07

ISS013-E-78506 (7 Sept. 2006) --- Sand dunes near Mongolia's Har Lake are featured in this image photographed by an Expedition 13 crewmember on the International Space Station. Har (or Black) Lake is located in the western part of the country within the Valley of Lakes--part of a system of closed basins that stretches across central Asia. According to scientists, these basins are the remnants of larger paleolakes that had begun to shrink in size by approximately five thousand years ago as regional climate became drier. Today, the Valley of Lakes is an important ecological resource for study of steppe grasslands, and as resting points for large numbers of migratory birds. Portions of the basin are designated as national parks or other protected areas, and Har Lake itself is an ecotourism destination (usually by horseback). This oblique view captures the dynamic nature of the landscape of Har Lake. The lake is encircled by sand dune fields which encroach on the lower slopes of the Tobhata Mountains to the west and south. Gaps in the mountains have been exploited by sand dunes moving eastward (indicating westerly winds) -- the most striking example being a series of dunes entering Har Lake along its southwestern shoreline. Here, the dune forms reflect the channeling of winds through the break in the mountain ridgeline, leading to dune crests oriented transverse to northwesterly winds. Another well-developed line of dunes is visible between Har and Baga Lakes. While these dunes appear to cut across a lake surface, the dunes have in fact moved across a narrow stream channel.

Harnessing Energy from the Sun for Six Billion People

ScienceCinema

Nocera, Daniel

2018-05-24

Daniel Nocera, a Massachusetts Institute of Technology professor whose recent research focuses on solar-powered fuels, presents a Brookhaven Science Associates Distinguished Lecture, titled "Harnessing Energy from the Sun for Six Billion People -- One at a Time."

Harnessing Power from Tides: State of the Art.

ERIC Educational Resources Information Center

Ryan, Paul R.

1979-01-01

Discussed is the current, world-wide status of tidal energy as a potential power source. Potential sites and global tidal power prospects are identified. New engineering concepts relevant to the harnessing of tidal power are identified and described. (BT)

77 FR 21100 - Change in Bank Control Notices; Formations of, Acquisitions by, and Mergers of Bank Holding...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-04-09

... Nichols, Washington, DC; to acquire voting shares of HarVest Bancorp, Inc., Gaithersburg, Maryland, and thereby indirectly acquire voting shares of HarVest Bank of Maryland, Rockville, Maryland. Comments on...

Analogous β-Carboline Alkaloids Harmaline and Harmine Ameliorate Scopolamine-Induced Cognition Dysfunction by Attenuating Acetylcholinesterase Activity, Oxidative Stress, and Inflammation in Mice

PubMed Central

Li, Shu-Ping; Wang, Yu-Wen; Qi, Sheng-Lan; Zhang, Yun-Peng; Deng, Gang; Ding, Wen-Zheng; Ma, Chao; Lin, Qi-Yan; Guan, Hui-Da; Liu, Wei; Cheng, Xue-Mei; Wang, Chang-Hong

2018-01-01

The analogous β-carboline alkaloids, harmaline (HAL) and harmine (HAR), possess a variety of biological properties, including acetylcholinesterase (AChE) inhibitory activity, antioxidant, anti-inflammatory, and many others, and have great potential for treating Alzheimer’s disease (AD). However, studies have showed that the two compounds have similar structures and in vitro AChE inhibitory activities but with significant difference in bioavailability. The objective of this study was to comparatively investigate the effects of HAL and HAR in memory deficits of scopolamine-induced mice. In the present study, mice were pretreated with HAL (2, 5, and 10 mg/kg), HAR (10, 20, and 30 mg/kg) and donepezil (5 mg/kg) by intragastrically for 7 days, and were daily intraperitoneal injected with scopolamine (1 mg/kg) to induce memory deficits and then subjected to behavioral evaluation by Morris water maze. To further elucidate the underlying mechanisms of HAL and HAR in improving learning and memory, the levels of various biochemical factors and protein expressions related to cholinergic function, oxidative stress, and inflammation were examined. The results showed that HAL and HAR could effectively ameliorate memory deficits in scopolamine-induced mice. Both of them exhibited an enhancement in cholinergic function by inhibiting AChE and inducing choline acetyltransferase (ChAT) activities, and antioxidant defense via increasing the antioxidant enzymes activities of superoxide dismutase and glutathione peroxidase, and reducing maleic diadehyde production, and anti-inflammatory effects through suppressing myeloperoxidase, tumor necrosis factor α, and nitric oxide as well as modulation of critical neurotransmitters such as acetylcholine (ACh), choline (Ch), L-tryptophan (L-Trp), 5-hydroxytryptamine (5-HT), γ-aminobutyric acid (γ-GABA), and L-glutamic acid (L-Glu). Furthermore, the regulations of HAL on cholinergic function, inflammation, and neurotransmitters were more striking than those of HAR, and HAL manifested a comparable antioxidant capacity to HAR. Remarkably, the effective dosage of HAL (2 mg/kg) was far lower than that of HAR (20 mg/kg), which probably due to the evidently differences in the bioavailability and metabolic stability of the two analogs. Taken together, all these results revealed that HAL may be a promising candidate compound with better anti-amnesic effects and pharmacokinetic characteristics for the treatments of AD and related diseases. PMID:29755345

Spatial cognition in a virtual reality home-cage extension for freely moving rodents

PubMed Central

Kaupert, Ursula; Frei, Katja; Bagorda, Francesco; Schatz, Alexej; Tocker, Gilad; Rapoport, Sophie; Derdikman, Dori

2017-01-01

Virtual reality (VR) environments are a powerful tool to investigate brain mechanisms involved in the behavior of animals. With this technique, animals are usually head fixed or secured in a harness, and training for cognitively more complex VR paradigms is time consuming. A VR apparatus allowing free animal movement and the constant operator-independent training of tasks would enable many new applications. Key prospective usages include brain imaging of animal behavior when carrying a miniaturized mobile device such as a fluorescence microscope or an optetrode. Here, we introduce the Servoball, a spherical VR treadmill based on the closed-loop tracking of a freely moving animal and feedback counterrotation of the ball. Furthermore, we present the complete integration of this experimental system with the animals’ group home cage, from which single individuals can voluntarily enter through a tunnel with radio-frequency identification (RFID)-automated access control and commence experiments. This automated animal sorter functions as a mechanical replacement of the experimenter. We automatically trained rats using visual or acoustic cues to solve spatial cognitive tasks and recorded spatially modulated entorhinal cells. When electrophysiological extracellular recordings from awake behaving rats were performed, head fixation can dramatically alter results, so that any complex behavior that requires head movement is impossible to achieve. We circumvented this problem with the use of the Servoball in open-field scenarios, as it allows the combination of open-field behavior with the recording of nerve cells, along with all the flexibility that a virtual environment brings. This integrated home cage with a VR arena experimental system permits highly efficient experimentation for complex cognitive experiments. NEW & NOTEWORTHY Virtual reality (VR) environments are a powerful tool for the investigation of brain mechanisms. We introduce the Servoball, a VR treadmill for freely moving rodents. The Servoball is integrated with the animals’ group home cage. Single individuals voluntarily enter using automated access control. Training is highly time-efficient, even for cognitively complex VR paradigms. PMID:28077665

NCCS Regression Test Harness

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tharrington, Arnold N.

2015-09-09

The NCCS Regression Test Harness is a software package that provides a framework to perform regression and acceptance testing on NCCS High Performance Computers. The package is written in Python and has only the dependency of a Subversion repository to store the regression tests.

76 FR 6136 - Change in Bank Control Notices; Acquisitions of Shares of a Bank or Bank Holding Company

Federal Register 2010, 2011, 2012, 2013, 2014

2011-02-03

... Beach, California; to acquire voting shares of HarVest BanCorp, Inc., Gaithersburg, Maryland, and thereby indirectly acquire voting shares of HarVest Bank of Maryland, Rockville, Maryland. Board of...

Evaluating the High Asia Reanalysis (HAR) using Gauge-based and Satellite Precipitation Data over High Mountain Asia

NASA Astrophysics Data System (ADS)

Pangaluru, K.; Velicogna, I.; Ciraci, E.; Mohajerani, Y.

2017-12-01

The Indus, Ganges and Brahmaputra (IGB) basins supply water for both domestic and agricultural demands, the latter of which is the mainstay of Indian economy. Here, we use high-resolution Asia Refined Analysis (HAR) rainfall datasets to study the spatial and temporal behavior of rainfall over the mountainous areas of the Indus, Ganges and Brahmaputra (IGB) over the period from 2001 to 2014. The validation of High Asia Refined Analysis (HAR) precipitation data is carried out with observational (GPCP, CRU and CPC) and satellite (TRMM_3B43) datasets for the period. We find that the relative differences between the HAR model and the satellite and gauge-based datasets varies between -9% and 67% for the seasonal mean and between 1% and 26% for the annual mean for all basins. The correlation between the HAR model and the observational datasets lies between 0.5 and 0.9 for all seasons. Spatial variations and monthly magnitudes of gridded precipitation trends are calculated by using the Mann-Kendall (MK) test and the Thei-Sen approach (TSA) respectively. We found significant positive trends precipitation grids over the IGB basins in the annual and monsoon season time frames, as opposed to winter and falls seasons.

Wireless Self-Acquistion of 12-Lead ECG via Android Smart Phone

NASA Technical Reports Server (NTRS)

Schlegel, Todd T.

2012-01-01

Researchers at NASA s Johnson Space Center and at Orbital Research, Inc. (a NASA SBIR grant recipient) have recently developed a dry-electrode harness that allows for self-acquisition of resting 12-lead ECGs by minimally trained laypersons. When used in conjunction with commercial wireless (e.g., Bluetooth(TM) or 802.11-enabled) 12-lead ECG devices and custom smart phone-based software, the collected 12-lead ECG data can also immediately be forwarded from any geographic location within cellular range to the user s physician(s) of choice. The system can also be used to immediately forward to central receiving stations 12-lead ECG data collected during space flight or during activities in any remote terrestrial location supported by an internet or cellular phone infrastructure. The main novel aspects of the system are first, the dry-electrode 12-lead ECG harness itself, and second, an accompanying Android(TM) smart phone-based wireless 12-lead ECG capability. The ECG harness nominally employs dry electrodes manufactured by Orbital Research, Inc, recently cleared through the Food and Drug Administration (FDA). However, other dry electrodes that are not yet FDA cleared, for example those recently developed by Nanosonic, Inc as part of another NASA SBIR grant, can also be used. The various advantageous features of the harness include: 1) laypersons can be quickly instructed on its correct use, remotely if necessary; 2) all tangled "leadwire spaghetti" is eliminated, as is the common clinical problem of "leadwire reversal"; 3) all adhesives and disposables are also eliminated, the harness being fully reusable; if multiple individuals intend to use use the same harness, then standard antimicrobial wipes can be employed to sterilize the dry electrodes (and harness surface if needed) between users; 5) padded cushions at the lateral sides of the torso function to press the left arm (LA) and right arm (RA) dry electrodes mounted on the cushions against sideward or downward-rested arms of the subject; 6) sufficient distal placement of the arm electrodes achieves good electrode abutment to the arms without the need for adhesives, straps, bands, bracelets, or gloves; 7) padding over the sternum avoids "tenting" in the V1 through V3 (and, when present, the V3R) electrode positions; 8) easy-to-don, one-piece design with an adjustable, front-side single point of connection and an adjustable shoulder strap; and 9) Lund or "modified Lund" placement of the dry electrodes, the results of which more effectively reproduce results from "standard" 12-lead ECG placements than do results from Mason-Likar placements. The main limitation of the harness is that "one size does not fit all", meaning that an appropriately sized harness (small, medium, large, etc) must be chosen on the basis of an individual's size. To facilitate the use of the harness with inexpensive, commodity-grade cell phones and tablet devices, 12-lead ECG software is also being developed to accompany the harness for wireless use with Android. For this part of the project, NASA has teamed with TopCoder, Inc and the Harvard-affiliated NASA Tournament Lab in sponsoring java-based software programming contests through TopCoder. While ECG signals from the harness can already be wirelessly received and thoroughly processed (locally or remotely) by commercial-grade conventional (as well as advanced) 12-lead ECG software running on Microsoft Windows(TM), the Android-based software, once completed, will "cast a wider net" by allowing for a greater percentage of cell phone owners to participate in inexpensive, store-and-forward recordings of 12-lead ECGs worldwide, including for example Android cell phone users in many remote, third-world locations. At the time of writing, the Android 12-lead ECG software platform consists of a basic but expanding graphical user interface and accompanying software that: 1) wirelessly receives the 12-lead ECG data stream from a Bluetooth-based, FDA-cleared 12-leaCG device attached to the harness; 2) locally stores the same data in binary format to the SD card on the Android cell phone; and 3) makes the data stream in available in real time, for now to TopCoder's java programming contestants.

Access to credit: beginning a new phase.

PubMed

1995-01-01

This article briefly describes an INSTRAW study of an income generation program in the Dominican Republic. The women in development program is operated by the Association for the Development of Micro-Enterprises in the Dominican Republic. The evaluation aims to quantify the results for men and women borrowers in terms of income, family health and nutrition, business reinvestment, job creation, and other measures. The aim is to compare findings between female household heads and non-heads. Findings support other empirical results showing increased sales and income after development. Women invested some of their additional income in their families' health, nutrition, and education. Women also hired other women and tended to employ more unpaid family members. 12% of employees were aged 7-14 years. The use of local community members, who were recent college graduates, as field officers was found to be an effective management tool. The young loan officers were successful in identifying potential clients and in creating accessible opportunities for advice and service. Loan officers increased the number of borrowers, and the program had low rates of nonpayment of loans. Comparisons between female heads and non-heads indicated different reasons for involvement in the program. Non-heads with other income providers reported personal reasons such as self realization and more money. Heads desired financial stability for the family and sometimes satisfaction of survival needs. Female heads tended to reinvest and expand their income-generating capacities. Women tended to increase their working space. This usually meant home space, since many women conducted their business at home. One obstacle was identified which limited income enhancement. For 30% of interviewed women a limit was set on available credit. Credit could only yield income equal to the minimum wage. This pilot study was limited to 400 persons from Santo Domingo. A further impact study is planned which would identify program strengths and weaknesses. Future plans for financial institutions and lending practices would be based on research findings.

Missing depth cues in virtual reality limit performance and quality of three dimensional reaching movements

PubMed Central

Mayo, Johnathan; Baur, Kilian; Wittmann, Frieder; Riener, Robert; Wolf, Peter

2018-01-01

Background Goal-directed reaching for real-world objects by humans is enabled through visual depth cues. In virtual environments, the number and quality of available visual depth cues is limited, which may affect reaching performance and quality of reaching movements. Methods We assessed three-dimensional reaching movements in five experimental groups each with ten healthy volunteers. Three groups used a two-dimensional computer screen and two groups used a head-mounted display. The first screen group received the typically recreated visual depth cues, such as aerial and linear perspective, occlusion, shadows, and texture gradients. The second screen group received an abstract minimal rendering lacking those. The third screen group received the cues of the first screen group and absolute depth cues enabled by retinal image size of a known object, which realized with visual renderings of the handheld device and a ghost handheld at the target location. The two head-mounted display groups received the same virtually recreated visual depth cues as the second or the third screen group respectively. Additionally, they could rely on stereopsis and motion parallax due to head-movements. Results and conclusion All groups using the screen performed significantly worse than both groups using the head-mounted display in terms of completion time normalized by the straight-line distance to the target. Both groups using the head-mounted display achieved the optimal minimum in number of speed peaks and in hand path ratio, indicating that our subjects performed natural movements when using a head-mounted display. Virtually recreated visual depth cues had a minor impact on reaching performance. Only the screen group with rendered handhelds could outperform the other screen groups. Thus, if reaching performance in virtual environments is in the main scope of a study, we suggest applying a head-mounted display. Otherwise, when two-dimensional screens are used, achievable performance is likely limited by the reduced depth perception and not just by subjects’ motor skills. PMID:29293512

Rate of regional nodal metastases of cutaneous squamous cell carcinoma in the immunosuppressed patient.

PubMed

McLaughlin, Eamon J; Miller, Lauren; Shin, Thuzar M; Sobanko, Joseph F; Cannady, Steven B; Miller, Christopher J; Newman, Jason G

Immunosuppressed solid organ transplant recipients (SOTRs) have an increased risk of developing cutaneous squamous cell carcinomas (cSCCs) with metastatic potential. This study sought to determine the rate of regional lymph node involvement in a large cohort of solid organ transplant patients with cutaneous head and neck squamous cell carcinoma. A retrospective chart review was performed on solid organ transplant patients with head and neck cutaneous squamous cell carcinoma treated at a tertiary academic medical center from 2005 to 2015. 130 solid organ transplant patients underwent resection of 383 head and neck cutaneous squamous cell carcinomas. The average age of the patient was 63. Seven patients (5%) developed regional lymph node metastases (3 parotid, 4 cervical lymph nodes). The mean time from primary tumor resection to diagnosis of regional lymphatic disease was 6.7months. Six of these patients underwent definitive surgical resection followed by adjuvant radiation; one patient underwent definitive chemoradiation. 6 of the 7 patients died of disease progression with a mean survival of 15months. The average follow up time was 3years (minimum 6months). Solid organ transplant recipients with cutaneous squamous cell carcinoma of the head and neck develop regional lymph node metastasis at a rate of 5%. Regional lymph node metastasis in this population has a poor prognosis and requires aggressive management and surveillance. Copyright © 2017 Elsevier Inc. All rights reserved.

Combined with Bone Marrow-Derived Cells and rhBMP-2 for Osteonecrosis after Femoral Neck Fractures in Children and Adolescents: A case series

PubMed Central

Gao, Fuqiang; Sun, Wei; Guo, Wanshou; Wang, Bailiang; Cheng, Liming; Li, Zirong

2016-01-01

Osteonecrosis of the femoral head (ONFH) following femoral neck fractures is a rare, yet severe, disorder in children and adolescents. This study evaluated the effectiveness of core decompression (CD) combined with implantation of bone marrow–derived cells (BMDC) and rhBMP-2 for osteonecrosis of femoral head (ONFH) after femoral neck fractures in children and adolescents. This study included 51 patients, aged 11.4–18.1 years, with ARCO stages I–III ONFH after femoral neck fractures between 2004 and 2010. The hips were divided into two groups based on whether the lateral pillar of the femoral head (LPFH) was preserved: LPFH and non-LPFH groups. All patients were followed up clinically and radiographically for a minimum of 5 years. 44 patients (86.3%) had improved clinical outcome. Radiologically, 9 of the 51 hips (17.6%) exhibited collapse onset or progression of the femoral head or narrowing of the hip joint space, and one patient in the non-LPFH group required hip arthroplasty due to the worsened syndrome. The technique provided an effective therapeutic option for children and adolescents with ONFH following femoral neck fractures. It relieves hip pain and prevents the progression of osteonecrosis in young patients lasting more than 5 years after surgery. PMID:27477836

The Annual Glaciohydrology Cycle in the Ablation Zone of the Greenland Ice Sheet: Part 1. Hydrology Model

NASA Technical Reports Server (NTRS)

Colgan, William; Rajaram, Harihar; Anderson, Robert; Steffen. Konrad; Phillips, Thomas; Zwally, H. Jay; Abdalati, Waleed

2012-01-01

We apply a novel one-dimensional glacier hydrology model that calculates hydraulic head to the tidewater-terminating Sermeq Avannarleq flowline of the Greenland ice sheet. Within a plausible parameter space, the model achieves a quasi-steady-state annual cycle in which hydraulic head oscillates close to flotation throughout the ablation zone. Flotation is briefly achieved during the summer melt season along a approx.17 km stretch of the approx.50 km of flowline within the ablation zone. Beneath the majority of the flowline, subglacial conduit storage closes (i.e. obtains minimum radius) during the winter and opens (i.e. obtains maximum radius) during the summer. Along certain stretches of the flowline, the model predicts that subglacial conduit storage remains open throughout the year. A calculated mean glacier water residence time of approx.2.2 years implies that significant amounts of water are stored in the glacier throughout the year. We interpret this residence time as being indicative of the timescale over which the glacier hydrologic system is capable of adjusting to external surface meltwater forcings. Based on in situ ice velocity observations, we suggest that the summer speed-up event generally corresponds to conditions of increasing hydraulic head during inefficient subglacial drainage. Conversely, the slowdown during fall generally corresponds to conditions of decreasing hydraulic head during efficient subglacial drainage.

Digibaro pressure instrument onboard the Phoenix Lander

NASA Astrophysics Data System (ADS)

Harri, A.-M.; Polkko, J.; Kahanpää, H. H.; Schmidt, W.; Genzer, M. M.; Haukka, H.; Savijarv1, H.; Kauhanen, J.

2009-04-01

The Phoenix Lander landed successfully on the Martian northern polar region. The mission is part of the National Aeronautics and Space Administration's (NASA's) Scout program. Pressure observations onboard the Phoenix lander were performed by an FMI (Finnish Meteorological Institute) instrument, based on a silicon diaphragm sensor head manufactured by Vaisala Inc., combined with MDA data processing electronics. The pressure instrument performed successfully throughout the Phoenix mission. The pressure instrument had 3 pressure sensor heads. One of these was the primary sensor head and the other two were used for monitoring the condition of the primary sensor head during the mission. During the mission the primary sensor was read with a sampling interval of 2 s and the other two were read less frequently as a check of instrument health. The pressure sensor system had a real-time data-processing and calibration algorithm that allowed the removal of temperature dependent calibration effects. In the same manner as the temperature sensor, a total of 256 data records (8.53 min) were buffered and they could either be stored at full resolution, or processed to provide mean, standard deviation, maximum and minimum values for storage on the Phoenix Lander's Meteorological (MET) unit.The time constant was approximately 3s due to locational constraints and dust filtering requirements. Using algorithms compensating for the time constant effect the temporal resolution was good enough to detect pressure drops associated with the passage of nearby dust devils.

Assessment of repeatability of a wireless, inertial sensor-based lameness evaluation system for horses.

PubMed

Keegan, Kevin G; Kramer, Joanne; Yonezawa, Yoshiharu; Maki, Hiromitchi; Pai, P Frank; Dent, Eric V; Kellerman, Thomas E; Wilson, David A; Reed, Shannon K

2011-09-01

To determine repeatability of a wireless, inertial sensor-based lameness evaluation system in horses. 236 horses. Horses were from 2 to 29 years of age and of various breeds and lameness disposition. All horses were instrumented with a wireless, inertial sensor-based motion analysis system on the head (accelerometer), pelvis (midline croup region [accelerometer]), and right forelimb (gyroscope) before evaluation in 2 consecutive trials, approximately 5 minutes apart, as the horse was trotted in a straight line. Signal-processing algorithms generated overall trial asymmetry measures for vertical head and pelvic movement and stride-by-stride differences in head and pelvic maximum and minimum positions between right and left sides of each stride. Repeatability was determined, and trial difference was determined for groups of horses with various numbers of strides for which data were collected per trial. Inertial sensor-based measures of torso movement asymmetry were repeatable. Repeatability for measures of torso asymmetry for determination of hind limb lameness was slightly greater than that for forelimb lameness. Collecting large numbers of strides degraded stride-to-stride repeatability but did not degrade intertrial repeatability. The inertial sensor system used to measure asymmetry of head and pelvic movement as an aid in the detection and evaluation of lameness in horses trotting in a straight line was sufficiently repeatable to investigate for clinical use.

Antibacterial activity of anthraquinone from cassia seed on spiced pig head

NASA Astrophysics Data System (ADS)

Xu, L. Y.; Li, X.; Cui, Y. Q.; Pang, M. X.; Wang, F.; Qi, J. H.

2018-01-01

[Objective] To optimize the extraction of anthraquinone from cassia seed by ultrasonic extraction and its antibacterial activity. [Method] The influences of different extraction time and ethanol concentration, on anthraquinone content were evaluated by a single factor experiment. And anthraquinone content was determined by ultraviolet spectrophotometry. The bacteriostasis of anthraquinone on spiced pig head’s common putrefying bacteria: Staphylococcus, Serratieae, Bacillus, Proteus and the minimal inhibitory concentration (MIC) were studied by oxford plate assay system. [Result] The best extraction time was 30 minutes and the best ethanol concentration was 80%. The antibacterial activity of the cassia seed anthraquinone on Staphylococcus Aureus, Bacillus Proteus is obviously, the minimum inhibitory concentrations were 0.125 g/mL, 0.125 g/mL, 1 g/mL respectively and no inhibitory effect on Serratieae. [Conclusions] The anthraquinones from Cassia seed can inhibit a part of spoilage bacteria in spiced pig heads.

Compact atom interferometer using single laser

NASA Astrophysics Data System (ADS)

Chiow, Sheng-wey; Yu, Nan

2018-06-01

A typical atom interferometer requires vastly different laser frequencies at different stages of operation, e.g., near resonant light for laser cooling and far detuned light for atom optics, such that multiple lasers are typically employed. The number of laser units constrains the achievable minimum size and power in practical devices for resource critical environments such as space. We demonstrate a compact atom interferometer accelerometer operated by a single diode laser. This is achieved by dynamically changing the laser output frequency in GHz range while maintaining spectroscopic reference to an atomic transition via a sideband generated by phase modulation. At the same time, a beam path sharing configuration is also demonstrated for a compact sensor head design, in which atom interferometer beams share the same path as that of the cooling beam. This beam path sharing also significantly simplifies three-axis atomic accelerometry in microgravity using single sensor head.

Establishment and characterization of a new fish cell line from head kidney of half-smooth tongue sole (Cynoglossus semilaevis).

PubMed

Zheng, Yuan; Wang, Na; Xie, Ming-Shu; Sha, Zhen-Xia; Chen, Song-Lin

2012-12-01

A new cell line (TSHKC) derived from half-smooth tongue sole (Cynoglossus semilaevis) head kidney was developed. The cell line was subcultured for 40 passages over a period of 360 days. The cell line was optimally maintained in minimum essential medium supplemented with HEPES, antibiotics, fetal bovine serum, 2-Mercaptoethanol (2-Me), sodium pyruvate and basic fibroblast growth factor. The suitable growth temperature for TSHKC cells was 24 °C, and microscopically, TSHKC cells were composed of fibroblast-like cells. Chromosome analysis revealed that the TSHKC cell line had a normal diploid karyotype with 2n = 42, contained the heterogametic W chromosome. The TSHKC cell line was found to be susceptible to lymphocystis disease virus. The fluorescent signals were observed in TSHKC when the cells were transfected with green fluorescent protein and red fluorescent protein reporter plasmids.

Effect of the Earned Income Tax Credit on Hospital Admissions for Pediatric Abusive Head Trauma, 1995-2013.

PubMed

Klevens, Joanne; Schmidt, Brian; Luo, Feijun; Xu, Likang; Ports, Katie A; Lee, Rosalyn D

Policies that increase household income, such as the earned income tax credit (EITC), have shown reductions on risk factors for child maltreatment (ie, poverty, maternal stress, depression), but evidence is lacking on whether the EITC actually reduces child maltreatment. We examined whether states' EITCs are associated with state rates of hospital admissions for abusive head trauma among children aged <2 years. We conducted difference-in-difference analyses (ie, pre- and postdifferences in intervention vs control groups) of annual rates of states' hospital admissions attributed to abusive head trauma among children aged <2 years (ie, using aggregate data). We conducted analyses in 14 states with, and 13 states without, an EITC from 1995 to 2013, differentiating refundable EITCs (ie, tax filer gets money even if taxes are not owed) from nonrefundable EITCs (ie, tax filer gets credit only for any tax owed), controlling for state rates of child poverty, unemployment, high school graduation, and percentage of non-Latino white people. A refundable EITC was associated with a decrease of 3.1 abusive head trauma admissions per 100 000 population in children aged <2 years after controlling for confounders ( P = .08), but a nonrefundable EITC was not associated with a decrease ( P = .49). Tax refunds ranged from $108 to $1014 and $165 to $1648 for a single parent working full-time at minimum wage with 1 child or 2 children, respectively. Our findings with others suggest that policies such as the EITC that increase household income may prevent serious abusive head trauma.

FTUC: A Flooding Tree Uneven Clustering Protocol for a Wireless Sensor Network.

PubMed

He, Wei; Pillement, Sebastien; Xu, Du

2017-11-23

Clustering is an efficient approach in a wireless sensor network (WSN) to reduce the energy consumption of nodes and to extend the lifetime of the network. Unfortunately, this approach requires that all cluster heads (CHs) transmit their data to the base station (BS), which gives rise to the long distance communications problem, and in multi-hop routing, the CHs near the BS have to forward data from other nodes that lead those CHs to die prematurely, creating the hot zones problem. Unequal clustering has been proposed to solve these problems. Most of the current algorithms elect CH only by considering their competition radius, leading to unevenly distributed cluster heads. Furthermore, global distances values are needed when calculating the competition radius, which is a tedious task in large networks. To face these problems, we propose a flooding tree uneven clustering protocol (FTUC) suited for large networks. Based on the construction of a tree type sub-network to calculate the minimum and maximum distances values of the network, we then apply the unequal cluster theory. We also introduce referenced position circles to evenly elect cluster heads. Therefore, cluster heads are elected depending on the node's residual energy and their distance to a referenced circle. FTUC builds the best inter-cluster communications route by evaluating a cluster head cost function to find the best next hop to the BS. The simulation results show that the FTUC algorithm decreases the energy consumption of the nodes and balances the global energy consumption effectively, thus extending the lifetime of the network.

[Leaf water potential of spring wheat and field pea under different tillage patterns and its relationships with environmental factors].

PubMed

Zhang, Ming; Zhang, Ren-Zhi; Cai, Li-Qun

2008-07-01

Based on a long-term experiment, the leaf water potential of spring wheat and field pea, its relationships with environmental factors, and the diurnal variations of leaf relative water content and water saturation deficient under different tillage patterns were studied. The results showed that during whole growth period, field pea had an obviously higher leaf water potential than spring wheat, but the two crops had similar diurnal variation trend of their leaf water potential, i.e., the highest in early morning, followed by a descent, and a gradual ascent after the descent. For spring wheat, the maximum leaf water potential appeared at its jointing and heading stages, followed by at booting and flowering stages, and the minimum appeared at filling stage. For field pea, the maximum leaf water potential achieved at squaring stage, followed by at branching and flowering stages, and the minimum was at podding stage. The leaf relative water content of spring wheat was the highest at heading stage, followed by at jointing and flowering stages, and achieved the minimum at filling stage; while the water saturation deficient was just in adverse. With the growth of field pea, its leaf relative water content decreased, but leaf water saturation deficient increased. The leaf water potential of both spring wheat and field pea had significant correlations with environmental factors, including soil water content, air temperature, solar radiation, relative air humidity, and air water potential. Path analysis showed that the meteorological factor which had the strongest effect on the diurnal variation of spring wheat' s and field pea' s leaf water potential was air water potential and air temperature, respectively. Compared with conventional tillage, the protective tillage patterns no-till, no-till plus straw mulching, and conventional tillage plus straw returning increased the leaf water potential and relative water content of test crops, and the effect of no-till plus straw mulching was most significant.

Program for improved electrical harness documentation and fabrication

NASA Technical Reports Server (NTRS)

1971-01-01

Computer program provides automated print-out of harness interconnection table and automated cross-check of reciprocal pin/connector assignments, and improves accuracy and reliability of final documented data. Programs and corresponding library tapes are successfully and continuously employed on Nimbus spacecraft programs.

Manufacturing and quality control of interconnecting wire harnesses, Volume 2

NASA Technical Reports Server (NTRS)

1972-01-01

Interconnecting wire harnesses defined in the design standard are considered, including type 4, open bundle (not enclosed). Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated into the document.

Going Below Minimums: The Efficacy of Display Enhanced/Synthetic Vision Fusion for Go-Around Decisions during Non-Normal Operations

NASA Technical Reports Server (NTRS)

Prinzel, Lawrence J., III; Kramer, Lynda J.; Bailey, Randall E.

2007-01-01

The use of enhanced vision systems in civil aircraft is projected to increase rapidly as the Federal Aviation Administration recently changed the aircraft operating rules under Part 91, revising the flight visibility requirements for conducting approach and landing operations. Operators conducting straight-in instrument approach procedures may now operate below the published approach minimums when using an approved enhanced flight vision system that shows the required visual references on the pilot's Head-Up Display. An experiment was conducted to evaluate the complementary use of synthetic vision systems and enhanced vision system technologies, focusing on new techniques for integration and/or fusion of synthetic and enhanced vision technologies and crew resource management while operating under these newly adopted rules. Experimental results specific to flight crew response to non-normal events using the fused synthetic/enhanced vision system are presented.

Estimation of the transmissivity of thin leaky-confined aquifers from single-well pumping tests

NASA Astrophysics Data System (ADS)

Worthington, Paul F.

1981-01-01

Data from the quasi-equilibrium phases of a step-drawdown test are used to evaluate the coefficient of non-linear head losses subject to the assumption of a constant effective well radius. After applying a well-loss correction to the observed drawdowns of the first step, an approximation method is used to estimate a pseudo-transmissivity of the aquifer from a single value of time-variant drawdown. The pseudo-transmissivities computed for each of a sequence of values of time pass through a minimum when there is least manifestation of casing-storage and leakage effects, phenomena to which pumping-test data of this kind are particularly susceptible. This minimum pseudo-transmissivity, adjusted for partial penetration effects where appropriate, constitutes the best possible estimate of aquifer transmissivity. The ease of application of the overall procedure is illustrated by a practical example.

Minimum-fuel turning climbout and descent guidance of transport jets

NASA Technical Reports Server (NTRS)

Neuman, F.; Kreindler, E.

1983-01-01

The complete flightpath optimization problem for minimum fuel consumption from takeoff to landing including the initial and final turns from and to the runway heading is solved. However, only the initial and final segments which contain the turns are treated, since the straight-line climbout, cruise, and descent problems have already been solved. The paths are derived by generating fields of extremals, using the necessary conditions of optimal control together with singular arcs and state constraints. Results show that the speed profiles for straight flight and turning flight are essentially identical except for the final horizontal accelerating or decelerating turns. The optimal turns require no abrupt maneuvers, and an approximation of the optimal turns could be easily integrated with present straight-line climb-cruise-descent fuel-optimization algorithms. Climbout at the optimal IAS rather than the 250-knot terminal-area speed limit would save 36 lb of fuel for the 727-100 aircraft.

Quality of harness fit for normal and low birthweight infants observed among newborns in infant car seats.

PubMed

Brown, Julie; Sinn, John Kam Hung; Chua, Aileen; Clarke, Elizabeth Clare

2017-04-01

Child restraint fit is important for crash protection. For newborns, standards universally require a rear-facing restraint and some upper limit on size, but historically there has been no specification of a lower design limit and there is concern over whether low birthweight infants (LBW) are adequately restrained. The aim of this study was to determine the quality of harness fit for newborns of low and normal weight in a range of modern child restraints. A convenience sample of infants (1.657-4.455 kg) were recruited from the postnatal ward and special care nursery <1 week from discharge. Infants (n=84) were assessed for harness fit in rear-facing-only restraints, convertible rear/forward restraints and a subset were assessed in a restraint specifically designed to accommodate LBW infants. Measures of harness fit were based on shoulder strap, crotch strap and buckle positioning. Less than 20% of infants achieved good harness fit, regardless of whether they were categorised as low (<2.5 kg) or normal weight. Rear-facing-only restraints were less likely to provide good fit than convertible restraints, in all measures of fit other than shoulder strap width. The proportions of infants achieving good fit were greater in the restraint designed for LBW infants than other restraint types. Poor accommodation continues to be a problem for LBW infants but is rectified in specifically designed restraints. Better specification of harness configuration for all rearward-facing restraints may be required to ensure adequate accommodation of normal birthweight infants. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Post Hoc Analyses of Anxiety Measures in Adult Patients With Generalized Anxiety Disorder Treated With Vilazodone

PubMed Central

Khan, Arif; Durgam, Suresh; Tang, Xiongwen; Ruth, Adam; Mathews, Maju; Gommoll, Carl P.

2016-01-01

Objective To investigate vilazodone, currently approved for major depressive disorder in adults, for generalized anxiety disorder (GAD). Method Three randomized, double-blind, placebo-controlled studies showing positive results for vilazodone (2,040 mg/d) in adult patients with GAD (DSM-IV-TR) were pooled for analyses; data were collected from June 2012 to March 2014. Post hoc outcomes in the pooled intent-to-treat population (n = 1,462) included mean change from baseline to week 8 in Hamilton Anxiety Rating Scale (HARS) total score, psychic and somatic anxiety subscale scores, and individual item scores; HARS response (≥ 50% total score improvement) and remission (total score ≤ 7) at week 8; and category shifts, defined as HARS item score ≥ 2 at baseline (moderate to very severe symptoms) and score of 0 at week 8 (no symptoms). Results The least squares mean difference was statistically significant for vilazodone versus placebo in change from baseline to week 8 in HARS total score (−1.83, P < .0001) and in psychic anxiety (−1.21, P < .0001) and somatic anxiety (−0.63, P < .01) subscale scores; differences from placebo were significant on 11 of 14 HARS items (P < .05). Response rates were higher with vilazodone than placebo (48% vs 39%, P < .001), as were remission rates (27% vs 21%, P < .01). The percentage of patients who shifted to no symptoms was significant for vilazodone on several items: anxious mood, tension, intellectual, depressed mood, somatic-muscular, somatic-sensory, cardiovascular, respiratory, and autonomic symptoms (P < .05). Conclusions Treatment with vilazodone versus placebo was effective in adult GAD patients, with significant differences between treatment groups found on both psychic and somatic HARS items. Trial Registration ClinicalTrials.gov identifiers: NCT01629966, NCT01766401, NCT01844115. PMID:27486544

Post Hoc Analyses of Anxiety Measures in Adult Patients With Generalized Anxiety Disorder Treated With Vilazodone.

PubMed

Khan, Arif; Durgam, Suresh; Tang, Xiongwen; Ruth, Adam; Mathews, Maju; Gommoll, Carl P

2016-01-01

To investigate vilazodone, currently approved for major depressive disorder in adults, for generalized anxiety disorder (GAD). Three randomized, double-blind, placebo-controlled studies showing positive results for vilazodone (2,040 mg/d) in adult patients with GAD (DSM-IV-TR) were pooled for analyses; data were collected from June 2012 to March 2014. Post hoc outcomes in the pooled intent-to-treat population (n = 1,462) included mean change from baseline to week 8 in Hamilton Anxiety Rating Scale (HARS) total score, psychic and somatic anxiety subscale scores, and individual item scores; HARS response (≥ 50% total score improvement) and remission (total score ≤ 7) at week 8; and category shifts, defined as HARS item score ≥ 2 at baseline (moderate to very severe symptoms) and score of 0 at week 8 (no symptoms). The least squares mean difference was statistically significant for vilazodone versus placebo in change from baseline to week 8 in HARS total score (-1.83, P < .0001) and in psychic anxiety (-1.21, P < .0001) and somatic anxiety (-0.63, P < .01) subscale scores; differences from placebo were significant on 11 of 14 HARS items (P < .05). Response rates were higher with vilazodone than placebo (48% vs 39%, P < .001), as were remission rates (27% vs 21%, P < .01). The percentage of patients who shifted to no symptoms was significant for vilazodone on several items: anxious mood, tension, intellectual, depressed mood, somatic-muscular, somatic-sensory, cardiovascular, respiratory, and autonomic symptoms (P < .05). Treatment with vilazodone versus placebo was effective in adult GAD patients, with significant differences between treatment groups found on both psychic and somatic HARS items. ClinicalTrials.gov identifiers: NCT01629966, NCT01766401, NCT01844115.

A Simple Two Aircraft Conflict Resolution Algorithm

NASA Technical Reports Server (NTRS)

Chatterji, Gano B.

2006-01-01

Conflict detection and resolution methods are crucial for distributed air-ground traffic management in which the crew in, the cockpit, dispatchers in operation control centers sad and traffic controllers in the ground-based air traffic management facilities share information and participate in the traffic flow and traffic control functions. This paper describes a conflict detection, and a conflict resolution method. The conflict detection method predicts the minimum separation and the time-to-go to the closest point of approach by assuming that both the aircraft will continue to fly at their current speeds along their current headings. The conflict resolution method described here is motivated by the proportional navigation algorithm, which is often used for missile guidance during the terminal phase. It generates speed and heading commands to rotate the line-of-sight either clockwise or counter-clockwise for conflict resolution. Once the aircraft achieve a positive range-rate and no further conflict is predicted, the algorithm generates heading commands to turn back the aircraft to their nominal trajectories. The speed commands are set to the optimal pre-resolution speeds. Six numerical examples are presented to demonstrate the conflict detection, and the conflict resolution methods.

Outcomes after surgery and postoperative radiotherapy for perineural spread of head and neck cutaneous squamous cell carcinoma.

PubMed

Warren, Timothy A; Panizza, Benedict; Porceddu, Sandro V; Gandhi, Mitesh; Patel, Parag; Wood, Martin; Nagle, Christina M; Redmond, Michael

2016-06-01

Queensland, Australia, has the highest rates of cutaneous squamous cell carcinoma (SCC). Perineural invasion (PNI) is associated with reduced local control and survival. A retrospective review of a prospective database of patients with clinical PNI from cutaneous SCC of the head and neck (SCCHN) treated with surgery and postoperative radiotherapy (PORT) between 2000 and 2011 and a minimum of 24 months follow-up. Patients were excluded if immunosuppressed, had non-SCC histology, or were treated palliatively. Fifty patients (mean age, 60 years) with median follow-up of 50 months were included in this study. A total of 54.8% of known primary tumors had incidental PNI. Ten percent had nodal disease at presentation. MRI neurogram was positive in 95.8%. Recurrence-free survival (RFS) at 5-years was 62%. Five-year disease-specific survival (DSS) and overall survival (OS) were 75% and 64%, respectively. There were no perioperative deaths. This report demonstrates that long-term survival is achievable in patients with clinical PNI from cutaneous SCCHN after surgery and PORT. © 2015 Wiley Periodicals, Inc. Head Neck 38: 824-831, 2016. © 2015 Wiley Periodicals, Inc.

Survey of patient dosimetry for head and neck cancer patients undergoing external radiotherapy treatment: a study from northeastern hospitals of India.

PubMed

Sharma, Arunkumar B; Singh, Tomcha Th; Singh, Khelendra N; Gartia, R K

2009-01-01

To study dosimetry of patients during the external radiotherapy of head and neck cancers from different hospitals of the northeastern region (NER) of India. 35 confirmed cases of head and neck cancers reporting to three different hospitals in the NER of India who underwent radiation treatment were the materials for the study. Dosimetry was carried out at 8(eight) anatomical points to these patients, namely, target (entrance and exit points), forehead, chest, abdomen, gonad, arm, and leg respectively by thermoluminescence (TL) as well as optically stimulated luminescence (OSL) dosimeters. Unlike conventional appliances, we used common iodized salt as TL/OSL phosphor. Patient dosimetry was found to vary with an average of 1.17 +/- 0.39 Sv at forehead, 1.24 +/- 0.39 Sv at chest, 0.52 +/- 0.13 Sv at gonad to a minimum of 0.26 +/- 0.07 Sv at leg areas when exposed to a cumulative dose of 65 Sv at the target. Maximum dose received from a stray radiation is about 1.5 Sv at forehead/chest and dosimetry of patient among the three centers is not significantly different at the 5% level of probability.

Effect of intermittent standing and walking on physiological changes induced by head-down bed rest

NASA Technical Reports Server (NTRS)

Vernikos, J.; Ludwig, D. A.; Ertl, A. C.; Wade, C. E.; Keil, L.; OHara, D.

1994-01-01

Continuous exposure to gravity may not be necessary to prevent compromised physiological function resulting from exposure to microgravity. However, minimum gravity (G) exposure requirements, effectiveness of passive Gz versus activity in a G field, and optimal G stimulus amplitude, duration, and frequency are unknown. To partially address these questions, a 4-day, 6 degree head-down bed rest (HDBR) study (one ambulatory control day, 4 full HDBR days, one recovery day) was conducted. Nine males, 30-50 yr, were subjected to four different +1 Gz (head-foot) exposure protocols (periodic standing or controlled walking for 2 or 4 h/day in 15 min doses), plus a continuous HDBR (0 Gz) control. Standing 4 h completely prevented and standing 2 h partially prevented post-HDBR orthostatic intolerance. Both walking conditions (2 h and 4 h) attenuated the decrease in peak VO2 and prevented the increased urinary Ca2+ excretion associated with HDBR. Both 4 h conditions (standing and walking) attenuated plasma volume loss during HDBR. It was concluded that various physiological systems benefit differentially from passive +1 Gz or activity in +1 Gz and the duration (2 h vs. 4 h) of the stimulus may be an important moderating factor.

Validation of an educative manual for patients with head and neck cancer submitted to radiation therapy 1

PubMed Central

da Cruz, Flávia Oliveira de Almeida Marques; Ferreira, Elaine Barros; Vasques, Christiane Inocêncio; da Mata, Luciana Regina Ferreira; dos Reis, Paula Elaine Diniz

2016-01-01

Abstract Objective: develop the content and face validation of an educative manual for patients with head and neck cancer submitted to radiation therapy. Method: descriptive methodological research. The Theory of Psychometrics was used for the validation process, developed by 15 experts in the theme area of the educative manual and by two language and publicity professionals. A minimum agreement level of 80% was considered to guarantee the validity of the material. Results: the items addressed in the assessment tool of the educative manual were divided in three blocks: objectives, structure and format, and relevance. Only one item, related to the sociocultural level of the target public, obtained an agreement rate <80%, and was reformulated based on the participants' suggestions. All other items were considered appropriate and/or complete appropriate in the three blocks proposed: objectives - 92.38%, structure and form - 89.74%, and relevance - 94.44%. Conclusion: the face and content validation of the educative manual proposed were attended to. This can contribute to the understanding of the therapeutic process the head and neck cancer patient is submitted to during the radiation therapy, besides supporting clinical practice through the nursing consultation. PMID:27305178

Harnessing Collaborative Annotations on Online Formative Assessments

ERIC Educational Resources Information Center

Lin, Jian-Wei; Lai, Yuan-Cheng

2013-01-01

This paper harnesses collaborative annotations by students as learning feedback on online formative assessments to improve the learning achievements of students. Through the developed Web platform, students can conduct formative assessments, collaboratively annotate, and review historical records in a convenient way, while teachers can generate…

Manufacture and quality control of interconnecting wire harnesses

NASA Technical Reports Server (NTRS)

1973-01-01

Four-volume series of documents has been prepared as standard reference. Each volume may be used separately and covers wire and cable preparation as well as harness fabrication and installation. Series should be useful addition to libraries of manufactures of electrical and electronic equipment.

SRB Altitude Switch Assembly Wire Harness Failure

NASA Technical Reports Server (NTRS)

Blanche, Jim

2002-01-01

This paper presents an assessment of two wire harness failures that had occurred in Solid Rocket Booster Altitude Switch Assemblies S/N 200001 and S/N 20002. A list of modifications to EDU #4 and modification of qualification units 2000001 and 2000002 are also presented.

High-aspect-ratio microstructures with versatile slanting angles on silicon by uniform metal-assisted chemical etching

NASA Astrophysics Data System (ADS)

Li, Liyi; Zhang, Cheng; Tuan, Chia-Chi; Chen, Yun; Wong, C.-P.

2018-05-01

High-aspect-ratio (HAR) microstructures on silicon (Si) play key roles in photonics and electromechanical devices. However, it has been challenging to fabricate HAR microstructures with slanting profiles. Here we report successful fabrication of uniform HAR microstructures with controllable slanting angles on (1 0 0)-Si by slanted uniform metal-assisted chemical etching (SUMaCE). The trenches have width of 2 µm, aspect ratio greater than 20:1 and high geometric uniformity. The slanting angles can be adjusted between 2-70° with respect to the Si surface normal. The results support a fundamental hypothesis that under the UMaCE condition, the preferred etching direction is along the normal of the thin film catalysts, regardless of the relative orientation of the catalyst to Si substrates or the crystalline orientation of the substrates. The SUMaCE method paves the way to HAR 3D microfabrication with arbitrary slanting profiles inside Si.

A fast-evolving human NPAS3 enhancer gained reporter expression in the developing forebrain of transgenic mice

PubMed Central

Kamm, Gretel B.; López-Leal, Rodrigo; Lorenzo, Juan R.; Franchini, Lucía F.

2013-01-01

The developmental brain gene NPAS3 stands out as a hot spot in human evolution because it contains the largest number of human-specific, fast-evolving, conserved, non-coding elements. In this paper we studied 2xHAR142, one of these elements that is located in the fifth intron of NPAS3. Using transgenic mice, we show that the mouse and chimp 2xHAR142 orthologues behave as transcriptional enhancers driving expression of the reporter gene lacZ to a similar NPAS3 expression subdomain in the mouse central nervous system. Interestingly, the human 2xHAR142 orthologue drives lacZ expression to an extended expression pattern in the nervous system. Thus, molecular evolution of 2xHAR142 provides the first documented example of human-specific heterotopy in the forebrain promoted by a transcriptional enhancer and suggests that it may have contributed to assemble the unique properties of the human brain. PMID:24218632

Monitoring contamination due to materials outgassing by QCM-based sensors

NASA Astrophysics Data System (ADS)

Dirri, Fabrizio

2016-07-01

F. Dirri, E. Palomba, A. Longobardo, D. Biondi, A. Boccaccini, E. Zampetti, B. Saggin, D. Scaccabarozzi, A. Tortora, A. Nanni, J. Alves, A. Tighe Outgassing from spacecraft materials often occurs and degassing contaminants can degrade critical spacecraft surfaces, such as optical systems, solar panels, thermal radiators and thermal management systems. The main contaminants are the water adsorbed by cold surface, organics from spacecraft structure, electronics, insulation and thrusters firings [1]. Thus, it is fundamental to monitor these low-outgassing rates especially in a long duration mission: Quartz Crystal Microbalance (QCM) based sensors (i.e. single and double crystal configurations) are a suitable instruments to monitor step by step these degradation processes which occur in space conditions. The Contamination Assessment Microbalance (CAM) is a device aimed at monitoring in-orbit contamination of sensitive surfaces and payloads on ESA's future satellites. The device, developed by a consortium of Italian research Institutes, is based on QCM technology, previously considered by NASA and ESA experiments performed on Space Shuttle and satellite missions [2,3,4]. CAM is a low mass (200 grams for the sensor head), low volume (smaller than 5x5x5 cm3 for the sensor head) and low power consumption (less than 1.5 W) sensor. The device is composed by: 1) the Sensor Head, containing a sensing crystal (which measures the deposited contaminant mass), a reference crystal (used as frequency reference), their related Proximity Electronics (PE) and a Temperature Control System (TCS); 2) the Main Electronics Unit (MEU), which acquires the signal in output from Sensor Head unit; 3) the Harness connecting Sensor Head and MEU; 4) the User Interface (UI) to read and display the data. The device shows several improvements, i.e. possibility to measure directly the crystal temperature (with an accuracy better than 0.1°C), large measurable mass range (from 5•10-9 to 7•10-4 g/cm2), large operative temperature range (from -80°C to 130°C), temperature stability within 0.5°C and good frequency resolution of 0.1 Hz. The instruments concept and the performance evaluation, based on tests performed on the QCM based sensors (i.e. simulating an outgassing source in space conditions), are presented in this work. References : [1] Soares et al. 2003, Proc. SPIE, 09/2000; [2] Miller 1982, Report NASA TM- 82457; [3] Tighe et al. 2009, AIP Conf. Proc. 1087, 195; [4] Wood et al. 1997, AIAA 97-0841

Performance enhancement of linear stirling cryocoolers

NASA Astrophysics Data System (ADS)

Korf, Herbert; Ruehlich, Ingo; Wiedmann, Th.

2000-12-01

Performance and reliability parameters of the AIM Stirling coolers have been presented in several previous publications. This paper focuses on recent developments at AIM for the COP improvement of cryocoolers in IR-detectors and systems applications. Improved COP of cryocoolers is a key for optimized form factors, weight and reliability. In addition, some systems are critical for minimum input power and consequently minimum electromagnetic interference or magnetic stray fields, heat sinking or minimum stress under high g-level, etc. Although performance parameters and loss mechanism are well understood and can be calculated precisely, several losses still had been excessive and needed to be minimized. The AIM program is based on the SADA I cryocooler, which now is optimized to carry 4.3 W net heat load at 77K. As this program will lead into applications on a space platform, in a next step AIM is introducing flexure bearings and in a final step, an advanced pulse tube cold head will be implemented. The performance of the SADA II cooler is also improved by using the same tools and methods than used for the performance increase of the SADA I cooler by a factor of two. The main features are summarized together with measured or calculated performance data.

Innovation in the Harnessing and Transfer of Technology: The Gran Mariscal de Ayacucho Foundation

ERIC Educational Resources Information Center

Lerner de Almea, Ruth

1977-01-01

Discusses the background, organization, success, problems, and functions of the Gran Mariscal de Ayacucho Foundation, Caracas, Venezuela, for producing human resources for the harnessing of scientific technology. The fellowship program supports study by students both at home and abroad. (SL)

Sea floor topography and backscatter intensity of the Historic Area Remediation Site (HARS), offshore of New York, based on multibeam surveys conducted in 1996, 1998, and 2000

USGS Publications Warehouse

Butman, Bradford; Danforth, W.W.; Knowles, S.C.; May, Brian; Serrett, Laurie

2000-01-01

An area offshore of Sandy Hook, New Jersey, has been used extensively for disposal of dredged and other materials, derived from the New York/New Jersey Harbor and surrounding areas, since the late 1800's (Figure 1). Between 1976 and 1995, the New York Bight Dredged Material Disposal Site, also known as the Mud Dump Site (Figure 2), received on average about 6 million cubic yards of material each year from federal and private maintenance dredging and from harbor deepening activities (Massa and others, 1996). In September 1997 the Mud Dump Site (MDS) was closed as an official ocean disposal site by the U.S. Environmental Protection Agency (http://www.epa.gov/), and the MDS and surrounding areas were designated as the Historic Area Remediation Site (HARS). The HARS is subdivided into a Primary Remediation Area (PRA, subdivided into 9 cells), a Buffer Zone, and a No-Discharge Zone (Figure 2). The sea floor of the HARS, approximately 9 square nautical miles in area, is being remediated by placing at least a one-meter cap of Category I (clean) dredged material on top of the existing surface sediments that exhibit varying degrees of degradation. (See http://www.nan.usace.army.mil/business/prjlinks/dmmp/benefic/hars.htm)(Category I sediments have no potential short or long-term impacts and are acceptable for unrestricted ocean disposal (EPA, 1996)). About 1.1 million cubic yards of dredged material for remediation was placed in the HARS in 1999, and 2.5 million cubic yards in 2000. Three multibeam echosounder surveys were carried out to map the topography and surficial geology of the HARS. The surveys were conducted November 23 - December 3, 1996, October 26 - November 11, 1998, and April 6 - 30, 2000. The surveys were carried out as part of a larger survey of the Hudson Shelf Valley and adjacent shelf (Butman and others, 1998, (http://pubs.usgs.gov/openfile/of98-616/). This report presents maps showing topography, shaded relief, and backscatter intensity (a measure of sea floor texture and roughness) at a scale of 1:25,000. Comparison of the topography and backscatter intensity from the three surveys show changes in topography and surficial sediment properties resulting from placement of dredged material in 1996 and 1997 prior to closure of the Mud Dump Site, as well as placement of capping material for remediation of the HARS. The surficial geology and sediments of the HARS and the surrounding region are described in Butman and others (1998), (http://pubs.usgs.gov/openfile/of98-616/, Schwab and others (1997, 2000, http://pubs.usgs.gov/openfile/of00-295/). A history of waste disposal in the New York Bight region is presented in Massa and others (1996).

Harnessing Technology to Support Learning

ERIC Educational Resources Information Center

Richardson, Tony; Ecclesfield, Nigel; Lewis, Christine

2008-01-01

In April 2008, one sees the start of the consultation on the second phase of the government's e-strategy for education, published in 2005 as "Harnessing technology: transforming learning and children's services." This follows hard on the heels of the progress report and implementation plan for the technology strategy for further…

The Belem Framework for Action: Harnessing the Power and Potential of Adult Learning and Education for a Viable Future

ERIC Educational Resources Information Center

Adult Learning, 2012

2012-01-01

This article presents the Belem Framework for Action. This framework focuses on harnessing the power and potential of adult learning and education for a viable future. This framework begins with a preamble on adult education and towards lifelong learning.

Manufacture and quality control of interconnecting wire harnesses, Volume 3

NASA Technical Reports Server (NTRS)

1972-01-01

The document covers interconnecting wire harnesses defined in the design standard, including type 6, enclosed in TFE heat shrink tubing; and type 7, flexible armored. Knowledge gained through experience on the Saturn 5 program coupled with recent advances in techniques, materials, and processes was incorporated into this document.

Experimental impact protection with advanced restraint systems : preliminary primate with air bag and inertia reel/inverted-y yoke torso harness.

DOT National Transportation Integrated Search

1969-02-01

Both the inverted-Y yoke torso harness with inertia reel and the air- bag restraint system have had extensive independent development for some time by several engineering and research organizations for both aviation and ground vehicle occupant protec...

Harnessing Linguistic Variation to Improve Education. Rethinking Education. Volume 5

ERIC Educational Resources Information Center

Yiakoumetti, Androula, Ed.

2012-01-01

This volume brings together research carried out in a variety of geographic and linguistic contexts including Africa, Asia, Australia, Canada, the Caribbean, Europe and the United States and explores efforts to incorporate linguistic diversity into education and to "harness" this diversity for learners' benefit. It challenges the largely…

77 FR 11791 - Airworthiness Directives; Saab AB, Saab Aerosystems Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-02-28

... installation wiring. For the reasons described above, this [EASA] AD requires a one- time [detailed] inspection... installation, and if corrosion is found repairing each affected harness braid or replacing each affected component and/or wiring harness. We are proposing this AD to detect and correct corrosion of critical system...

77 FR 29855 - Airworthiness Directives; Saab AB, Saab Aerosystems Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-21

... electronic installation wiring. For the reasons described above, this [EASA] AD requires a one- time... corrosion of the electrical and electronics installation, and if corrosion is found repairing each affected harness braid or replacing each affected component and/or wiring harness. We are issuing this AD to detect...

Development of an intervention program to encourage shoulder harness use and aircraft retrofit in general aviation aircraft : phases I and II.

DOT National Transportation Integrated Search

1995-01-01

This report describes a study of shoulder harness installation and use rates in general aviation aircraft. Observations were made at six geographically separate areas to determine estimates of current installation and use rates. An expert panel was e...

Harness the Power of Technology

ERIC Educational Resources Information Center

Duncan, Arne

2011-01-01

Today, U.S. educators are teaching in the midst of a technological revolution. Technology promises to provide innovative solutions in the nation's classrooms, just as it has transformed the way people communicate, socialize, and conduct business. In this article, the author argues that now is the time to harness technology to revolutionize the way…

Personalizing Learning through the Use of Technology

ERIC Educational Resources Information Center

Robinson, Carol; Sebba, Judy

2010-01-01

In March 2005, the Department for Education and Skills published its e-strategy, Harnessing Technology (DfES, 2005, Harnessing technology: Transforming Learning and Children's Services). Within this, two of its key objectives were: firstly to transform teaching and learning, and help to improve outcomes for children and young people, through…

Reliable Wiring Harness

NASA Technical Reports Server (NTRS)

Gaspar, Kenneth C.

1987-01-01

New harness for electrical wiring includes plugs that do not loosen from vibration. Ground braids prevented from detaching from connectors and constrained so braids do not open into swollen "birdcage" sections. Spring of stainless steel encircles ground braid. Self-locking connector contains ratchet not only preventing connector from opening, but tightens when vibrated.

Reliability in fiber optic cable harness manufacturing

NASA Astrophysics Data System (ADS)

McCoy, Bruce M.

Key aspects of manufacturing cable harnesses for aircraft and spacecraft that incorporate optical fiber/cables along with traditional wiring are discussed. Issues regarding feasibility of automation of assembly processes, manual assembly, testing, installation, quality assurance, reliability and maintainability are addressed. Training procedures, formal training programs, and their results are reviewed.

78 FR 28725 - Airworthiness Directives; Spectrolab Nightsun XP Searchlight

Federal Register 2010, 2011, 2012, 2013, 2014

2013-05-16

... helicopter and remaining attached solely by the internal cable harness, or separating totally. This condition... Searchlight/ Gimbal could disconnect from the helicopter and remain attached solely by the internal cable harness or separate totally, resulting in damage to the helicopter or injury to persons on the ground...

77 FR 13993 - Airworthiness Directives; Spectrolab Nightsun XP Searchlight

Federal Register 2010, 2011, 2012, 2013, 2014

2012-03-08

.../Gimbal could disconnect from the helicopter and remain attached solely by the internal cable harness or... from the helicopter and remaining attached soley by the internal cable harness, or separating totally... incorporates two positive locking mechanisms: a torque value and safety wire applied to the nut. These locking...

African goat improvement project: A feed the future initiative harnessing geneticdiversity for conservation, disease resistance, and improved productivity

USDA-ARS?s Scientific Manuscript database

AFRICAN GOAT IMPROVEMENT PROJECT: A FEED THE FUTURE INITIATIVE HARNESSING GENETIC DIVERSITY FOR CONSERVATION, DISEASE RESISTANCE, AND IMPROVED PRODUCTIVITY Food production systems in Africa depend heavily on the use of locally adapted animals. These animals are of agricultural, cultural, and econom...

The buffering capacity of stems: genetic architecture of nonstructural carbohydrates in cultivated Asian rice, Oryza sativa.

PubMed

Wang, Diane R; Han, Rongkui; Wolfrum, Edward J; McCouch, Susan R

2017-07-01

Harnessing stem carbohydrate dynamics in grasses offers an opportunity to help meet future demands for plant-based food, fiber and fuel production, but requires a greater understanding of the genetic controls that govern the synthesis, interconversion and transport of such energy reserves. We map out a blueprint of the genetic architecture of rice (Oryza sativa) stem nonstructural carbohydrates (NSC) at two critical developmental time-points using a subpopulation-specific genome-wide association approach on two diverse germplasm panels followed by quantitative trait loci (QTL) mapping in a biparental population. Overall, 26 QTL are identified; three are detected in multiple panels and are associated with starch-at-maturity, sucrose-at-maturity and NSC-at-heading. They tag OsHXK6 (rice hexokinase), ISA2 (rice isoamylase) and a tandem array of sugar transporters. This study provides the foundation for more in-depth molecular investigation to validate candidate genes underlying rice stem NSC and informs future comparative studies in other agronomically vital grass species. © 2017 The Authors. New Phytologist © 2017 New Phytologist Trust.

Optimization techniques using MODFLOW-GWM

USGS Publications Warehouse

Grava, Anna; Feinstein, Daniel T.; Barlow, Paul M.; Bonomi, Tullia; Buarne, Fabiola; Dunning, Charles; Hunt, Randall J.

2015-01-01

An important application of optimization codes such as MODFLOW-GWM is to maximize water supply from unconfined aquifers subject to constraints involving surface-water depletion and drawdown. In optimizing pumping for a fish hatchery in a bedrock aquifer system overlain by glacial deposits in eastern Wisconsin, various features of the GWM-2000 code were used to overcome difficulties associated with: 1) Non-linear response matrices caused by unconfined conditions and head-dependent boundaries; 2) Efficient selection of candidate well and drawdown constraint locations; and 3) Optimizing against water-level constraints inside pumping wells. Features of GWM-2000 were harnessed to test the effects of systematically varying the decision variables and constraints on the optimized solution for managing withdrawals. An important lesson of the procedure, similar to lessons learned in model calibration, is that the optimized outcome is non-unique, and depends on a range of choices open to the user. The modeler must balance the complexity of the numerical flow model used to represent the groundwater-flow system against the range of options (decision variables, objective functions, constraints) available for optimizing the model.

The buffering capacity of stems: genetic architecture of nonstructural carbohydrates in cultivated Asian rice, Oryza sativa

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Diane R.; Han, Rongkui; Wolfrum, Edward J.

Harnessing stem carbohydrate dynamics in grasses offers an opportunity to help meet future demands for plant-based food, fiber and fuel production, but requires a greater understanding of the genetic controls that govern the synthesis, interconversion and transport of such energy reserves. We map out a blueprint of the genetic architecture of rice ( Oryza sativa) stem nonstructural carbohydrates (NSC) at two critical developmental time-points using a subpopulation-specific genome-wide association approach on two diverse germplasm panels followed by quantitative trait loci (QTL) mapping in a biparental population. Overall, 26 QTL are identified; three are detected in multiple panels and are associatedmore » with starch-at-maturity, sucrose-at-maturity and NSC-at-heading. They tag OsHXK6 (rice hexokinase), ISA2 (rice isoamylase) and a tandem array of sugar transporters. Furthermore, this study provides the foundation for more in-depth molecular investigation to validate candidate genes underlying rice stem NSC and informs future comparative studies in other agronomically vital grass species.« less

The kick with the kite: an analysis of kite surfing related off shore rescue missions in Cape Town, South Africa

PubMed Central

Exadaktylos, A; Sclabas, G; Blake, I; Swemmer, K; McCormick, G; Erasmus, P; Muhm, M; Curatolo, M

2005-01-01

Methods: The observation period for this study started on October 1, 2003 and ended on May 1, 2004 and included 30 air rescue missions. Data and information were collected prospectively. Results: The Air Mercy Service in Cape Town Province responded to 30 requests for help. Twenty five accidents were attributed to inability to detach the kite from the harness. Injuries occurred in five incidents and included fractures of the upper arm, ribs and ankle, and lacerations and contusions to the head and neck. Two patients suffered from hypothermia and one experienced severe exhaustion. All surfers were rescued successfully and there were no fatal accidents. Discussion: The risk potential of this new sport is unclear. Dangerous situations can occur despite proper training and safety precautions due to unpredictable conditions and difficulties with equipment. Safety should be stressed. Surfers should sailing with a fellow kiter and should wear a life vest. More efforts must be taken to make this booming new water sport safer. PMID:15849279

The buffering capacity of stems: genetic architecture of nonstructural carbohydrates in cultivated Asian rice, Oryza sativa

DOE PAGES

Wang, Diane R.; Han, Rongkui; Wolfrum, Edward J.; ...

2017-05-30

Harnessing stem carbohydrate dynamics in grasses offers an opportunity to help meet future demands for plant-based food, fiber and fuel production, but requires a greater understanding of the genetic controls that govern the synthesis, interconversion and transport of such energy reserves. We map out a blueprint of the genetic architecture of rice ( Oryza sativa) stem nonstructural carbohydrates (NSC) at two critical developmental time-points using a subpopulation-specific genome-wide association approach on two diverse germplasm panels followed by quantitative trait loci (QTL) mapping in a biparental population. Overall, 26 QTL are identified; three are detected in multiple panels and are associatedmore » with starch-at-maturity, sucrose-at-maturity and NSC-at-heading. They tag OsHXK6 (rice hexokinase), ISA2 (rice isoamylase) and a tandem array of sugar transporters. Furthermore, this study provides the foundation for more in-depth molecular investigation to validate candidate genes underlying rice stem NSC and informs future comparative studies in other agronomically vital grass species.« less

Diversity amongst trigeminal neurons revealed by high throughput single cell sequencing

PubMed Central

Nguyen, Minh Q.; Wu, Youmei; Bonilla, Lauren S.; von Buchholtz, Lars J.

2017-01-01

The trigeminal ganglion contains somatosensory neurons that detect a range of thermal, mechanical and chemical cues and innervate unique sensory compartments in the head and neck including the eyes, nose, mouth, meninges and vibrissae. We used single-cell sequencing and in situ hybridization to examine the cellular diversity of the trigeminal ganglion in mice, defining thirteen clusters of neurons. We show that clusters are well conserved in dorsal root ganglia suggesting they represent distinct functional classes of somatosensory neurons and not specialization associated with their sensory targets. Notably, functionally important genes (e.g. the mechanosensory channel Piezo2 and the capsaicin gated ion channel Trpv1) segregate into multiple clusters and often are expressed in subsets of cells within a cluster. Therefore, the 13 genetically-defined classes are likely to be physiologically heterogeneous rather than highly parallel (i.e., redundant) lines of sensory input. Our analysis harnesses the power of single-cell sequencing to provide a unique platform for in silico expression profiling that complements other approaches linking gene-expression with function and exposes unexpected diversity in the somatosensory system. PMID:28957441

Simplified configuration for the combustor of an oil burner using a low pressure, high flow air-atomizing nozzle

DOEpatents

Butcher, Thomas A.; Celebi, Yusuf; Fisher, Leonard

2000-09-15

The invention relates to clean burning of fuel oil with air. More specifically, to a fuel burning combustion head using a low-pressure, high air flow atomizing nozzle so that there will be a complete combustion of oil resulting in a minimum emission of pollutants. The improved fuel burner uses a low pressure air atomizing nozzle that does not result in the use of additional compressors or the introduction of pressurized gases downstream, nor does it require a complex design. Inventors:

Cooperative fault-tolerant distributed computing U.S. Department of Energy Grant DE-FG02-02ER25537 Final Report

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sunderam, Vaidy S.

2007-01-09

The Harness project has developed novel software frameworks for the execution of high-end simulations in a fault-tolerant manner on distributed resources. The H2O subsystem comprises the kernel of the Harness framework, and controls the key functions of resource management across multiple administrative domains, especially issues of access and allocation. It is based on a “pluggable” architecture that enables the aggregated use of distributed heterogeneous resources for high performance computing. The major contributions of the Harness II project result in significantly enhancing the overall computational productivity of high-end scientific applications by enabling robust, failure-resilient computations on cooperatively pooled resource collections.

Evaluation of Human and AutomationRobotics Integration Needs for Future Human Exploration Missions

NASA Technical Reports Server (NTRS)

Marquez, Jessica J.; Adelstein, Bernard D.; Ellis, Stephen; Chang, Mai Lee; Howard, Robert

2016-01-01

NASA employs Design Reference Missions (DRMs) to define potential architectures for future human exploration missions to deep space, the Moon, and Mars. While DRMs to these destinations share some components, each mission has different needs. This paper focuses on the human and automation/robotic integration needs for these future missions, evaluating them with respect to NASA research gaps in the area of space human factors engineering. The outcomes of our assessment is a human and automation/robotic (HAR) task list for each of the four DRMs that we reviewed (i.e., Deep Space Sortie, Lunar Visit/Habitation, Deep Space Habitation, and Planetary), a list of common critical HAR factors that drive HAR design.

Posterior glenoid bone grafting in total shoulder arthroplasty for osteoarthritis with severe posterior glenoid wear.

PubMed

Nicholson, Gregory P; Cvetanovich, Gregory L; Rao, Allison J; O'Donnell, Patrick

2017-10-01

Total shoulder arthroplasty (TSA) in cases with posterior wear can be addressed by eccentric reaming of the anterior glenoid or by augmenting the posterior glenoid with bone grafting or augmented glenoid implants. We report the results of TSA with posterior glenoid bone grafting (PGBG) with humeral head autograft in patients with shoulder osteoarthritis and severe posterior glenoid wear. A retrospective review of cases from 2004 to 2014 revealed 34 patients. Preoperative and postoperative radiographs were evaluated for glenoid version and humeral head subluxation as well as component loosening. Patient-reported outcomes were compared preoperatively and postoperatively. Complications and reoperations were also evaluated. Of the 34 patients, 28 (82.4%) were available at a minimum of 2 years' follow-up. PGBG corrected glenoid retroversion from -28° ± 4° preoperatively to -4° ± 2° (P < .001). Humeral head subluxation also improved after PGBG with respect to the scapular axis and to the midglenoid face (P < .001). Radiographic analysis revealed all PGBGs had incorporated. Radiographically, 3 patients (10.7%) had a total of 5 broken or displaced screws. In addition, 3 patients (10.7%) had a broken metal marker in the center peg of the glenoid component. No patients required component revision surgery by final follow-up. Only 1 reoperation occurred for capsular release. Patients showed significant improvements in all patient-reported outcomes. Patients undergoing primary TSA with humeral head autograft PGBG showed significant improvements in glenoid version, humeral head subluxation, patient-reported outcomes, and range of motion at an average of 4 years' follow-up. There was a low revision rate and a high rate of graft incorporation. Copyright © 2017 Journal of Shoulder and Elbow Surgery Board of Trustees. Published by Elsevier Inc. All rights reserved.

An objective frequency domain method for subsurface characterisation using Earth and atmospheric tides

NASA Astrophysics Data System (ADS)

Cuthbert, M. O.; Acworth, I. R.; Halloran, L. J. S.; Rau, G. C.; Bernadi, T. L.

2017-12-01

It has long been recognised that hydraulic properties can be derived from the response of piezometric heads to tidal loadings. However, there is a degree of subjectivity in existing graphical approaches most commonly used to calculate barometric efficiency leading to uncertainties in derived values of compressible storage. Here we demonstrate a novel approach to remove these uncertainties by objectively deriving the barometric efficiency from groundwater hydraulic head responses using a frequency domain method. We take advantage of the presence of worldwide and ubiquitous atmospheric tide fluctuations which occur at 2 cycles per day (cpd). First we use a Fourier transform to calculate the amplitudes of the 2 cpd signals from co-located atmospheric pressure and hydraulic head time series measurements. Next we show how the Earth tide response at the same frequency can be quantified and removed so that this effect does not interfere with the calculation of the barometric efficiency. Finally, the ratio of the amplitude of the response at 2 cpd of hydraulic head to atmospheric pressure is used to quantify the barometric efficiency. This new method allows an objective quantification using `passive' in situ monitoring rather than resorting to aquifer pumping or laboratory tests. The minimum data requirements are 15 days duration of 6-hourly hydraulic head and atmospheric pressure measurements, and modelled Earth tide records which are readily conducted using freely available software. The new approach allows for a rapid and cost-effective alternative to traditional methods of estimating aquifer compressible storage properties without the subjectivity of existing approaches, and will be of importance to improving the spatial coverage of subsurface characterisation for groundwater resource evaluation and land subsidence assessment.

A balanced solution to the cumulative threat of industrialized wind farm development on cinereous vultures (Aegypius monachus) in south-eastern Europe.

PubMed

Vasilakis, Dimitris P; Whitfield, D Philip; Kati, Vassiliki

2017-01-01

Wind farm development can combat climate change but may also threaten bird populations' persistence through collision with wind turbine blades if such development is improperly planned strategically and cumulatively. Such improper planning may often occur. Numerous wind farms are planned in a region hosting the only cinereous vulture population in south-eastern Europe. We combined range use modelling and a Collision Risk Model (CRM) to predict the cumulative collision mortality for cinereous vulture under all operating and proposed wind farms. Four different vulture avoidance rates were considered in the CRM. Cumulative collision mortality was expected to be eight to ten times greater in the future (proposed and operating wind farms) than currently (operating wind farms), equivalent to 44% of the current population (103 individuals) if all proposals are authorized (2744 MW). Even under the most optimistic scenario whereby authorized proposals will not collectively exceed the national target for wind harnessing in the study area (960 MW), cumulative collision mortality would still be high (17% of current population) and likely lead to population extinction. Under any wind farm proposal scenario, over 92% of expected deaths would occur in the core area of the population, further implying inadequate spatial planning and implementation of relevant European legislation with scant regard for governmental obligations to protect key species. On the basis of a sensitivity map we derive a spatially explicit solution that could meet the national target of wind harnessing with a minimum conservation cost of less than 1% population loss providing that the population mortality (5.2%) caused by the operating wind farms in the core area would be totally mitigated. Under other scenarios, the vulture population would probably be at serious risk of extinction. Our 'win-win' approach is appropriate to other potential conflicts where wind farms may cumulatively threaten wildlife populations.

A balanced solution to the cumulative threat of industrialized wind farm development on cinereous vultures (Aegypius monachus) in south-eastern Europe

PubMed Central

Whitfield, D. Philip; Kati, Vassiliki

2017-01-01

Wind farm development can combat climate change but may also threaten bird populations’ persistence through collision with wind turbine blades if such development is improperly planned strategically and cumulatively. Such improper planning may often occur. Numerous wind farms are planned in a region hosting the only cinereous vulture population in south-eastern Europe. We combined range use modelling and a Collision Risk Model (CRM) to predict the cumulative collision mortality for cinereous vulture under all operating and proposed wind farms. Four different vulture avoidance rates were considered in the CRM. Cumulative collision mortality was expected to be eight to ten times greater in the future (proposed and operating wind farms) than currently (operating wind farms), equivalent to 44% of the current population (103 individuals) if all proposals are authorized (2744 MW). Even under the most optimistic scenario whereby authorized proposals will not collectively exceed the national target for wind harnessing in the study area (960 MW), cumulative collision mortality would still be high (17% of current population) and likely lead to population extinction. Under any wind farm proposal scenario, over 92% of expected deaths would occur in the core area of the population, further implying inadequate spatial planning and implementation of relevant European legislation with scant regard for governmental obligations to protect key species. On the basis of a sensitivity map we derive a spatially explicit solution that could meet the national target of wind harnessing with a minimum conservation cost of less than 1% population loss providing that the population mortality (5.2%) caused by the operating wind farms in the core area would be totally mitigated. Under other scenarios, the vulture population would probably be at serious risk of extinction. Our ‘win-win’ approach is appropriate to other potential conflicts where wind farms may cumulatively threaten wildlife populations. PMID:28231316

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kirkpatrick, R. C.

Nuclear fusion was discovered experimentally in 1933-34 and other charged particle nuclear reactions were documented shortly thereafter. Work in earnest on the fusion ignition problem began with Edward Teller's group at Los Alamos during the war years. His group quantified all the important basic atomic and nuclear processes and summarized their interactions. A few years later, the success of the early theory developed at Los Alamos led to very successful thermonuclear weapons, but also to decades of unsuccessful attempts to harness fusion as an energy source of the future. The reasons for this history are many, but it seems appropriatemore » to review some of the basics with the objective of identifying what is essential for success and what is not. This tutorial discusses only the conditions required for ignition in small fusion targets and how the target design impacts driver requirements. Generally speaking, the driver must meet the energy, power and power density requirements needed by the fusion target. The most relevant parameters for ignition of the fusion fuel are the minimum temperature and areal density (rhoR), but these parameters set secondary conditions that must be achieved, namely an implosion velocity, target size and pressure, which are interrelated. Despite the apparent simplicity of inertial fusion targets, there is not a single mode of fusion ignition, and the necessary combination of minimum temperature and areal density depends on the mode of ignition. However, by providing a magnetic field of sufficient strength, the conditions needed for fusion ignition can be drastically altered. Magnetized target fusion potentially opens up a vast parameter space between the extremes of magnetic and inertial fusion.« less

Oropharyngeal candidiasis in head and neck cancer patients in Iran: Species identification, antifungal susceptibility and pathogenic characterization.

PubMed

Jahanshiri, Z; Manifar, S; Moosa, H; Asghari-Paskiabi, F; Mahmoodzadeh, H; Shams-Ghahfarokhi, M; Razzaghi-Abyaneh, M

2018-06-01

Oropharyngeal candidiasis (OPC) is the most frequent opportunistic fungal infection in head and neck cancer patients. This study was done to identify the Candida species, which cause OPC, and to evaluate their antifungal susceptibility pattern and pathogenic characteristics in Iranian head and neck cancer patients treated by radiotherapy. The oral clinical samples were determined by culturing on CHROMagar, carbohydrate assimilation and ITS sequencing methods. Biofilm formation, phospholipase and proteinase activity and antifungal susceptibility were examined too. Among 54 patients with confirmed OPC, 39 (72.22%) patients were male and 15 (27.77%) were female. The most frequently Candida species from a total of 60 isolates was C. albicans (53.3%), followed by C. tropicalis (21.66%), C. glabrata (15%), C. kefyr (5%) and C. dubliniensis (1.66%). All the isolates were high-producers of biofilm. All of Candida isolates were proteinase positive and 47 isolates (81.04%) represented phospholipase activity. The maximum and minimum rates of antifungal resistance belonged to ketoconazole (93.75% of C. albicans and 89.28% of Candida non-albicans) and fluconazole (62.50% and 42.85% of C. albicans and Candida non-albicans), respectively. The most effective antifungal against all candida isolates was fluconazole. Our data can estimate abundance of OPC in male and female head and neck cancer patients and is helpful to use effective strategies for antifungal treatment, prophylaxis, and preventive therapies in these patients. Copyright © 2018. Published by Elsevier Masson SAS.

DURIP: Electrokinetic Injection and Separation System for Analysis of Protein and Peptide Transport, Adsorption and Kinetics Instrumentation Proposal

DTIC Science & Technology

2015-03-18

both the electric double layer that forms at a solid-liquid interface as well as the biomolecules themselves, we can harness the coupled physics of...the biomolecules themselves, we can harness the coupled physics of complex biological fluids in nanofluidic channels towards unique, efficient

Harnessing ICT Potential: The Adoption and Analysis of ICT Systems for Enhancing the Student Learning Experience

ERIC Educational Resources Information Center

Dawson, Shane; Heathcote, Liz; Poole, Gary

2010-01-01

Purpose: This paper aims to examine how effective higher education institutions have been in harnessing the data capture mechanisms from their student information systems, learning management systems and communication tools for improving the student learning experience and informing practitioners of the achievement of specific learning outcomes.…

The Facebook-in-Action: Challenging, Harnessing and Enhancing Students Class Assignments and Projects

ERIC Educational Resources Information Center

Saifudin, Adam Mohd; Yacob, Aizan; Saad, Rohaizah

2016-01-01

Issues of universities students harnessing and capitalizing the usage of Facebook for their own learning capabilities and effective thinking is always the focus of education scholars, in assessing the quality class assignments and projects produced by them. Therefore, Facebook is now becoming unbearable influence since the internet activation in…

Using Discussion Methods to Inspire Diversity: Harnessing Social & Cultural Capital

ERIC Educational Resources Information Center

Raison, Brian; Gordon, Beverly

2012-01-01

How can you better harness the powerful social capital that exists within diverse individuals, families, businesses, and schools to make positive impacts in your community? What could you add to your next meeting--a Chamber strategic planning session, an employee wellness program, a non-profit board development--to better connect participants with…

Harnessing the Power of Interactivity for Instruction.

ERIC Educational Resources Information Center

Borsook, Terry K.

Arguing that what sets the computer apart from all other teaching devices is its potential for interactivity, this paper examines the concept of interactivity and explores ways in which its power can be harnessed and put to work. A discussion of interactivity in human-to-human communication sets a context within which to view human/computer…

14 CFR 91.105 - Flight crewmembers at stations.

Code of Federal Regulations, 2011 CFR

2011-01-01

... crewmember of a U.S.-registered civil aircraft shall, during takeoff and landing, keep his or her shoulder... at the crewmember's station is not equipped with a shoulder harness; or (2) The crewmember would be unable to perform required duties with the shoulder harness fastened. [Doc. No. 18334, 54 FR 34294, Aug...

14 CFR 91.105 - Flight crewmembers at stations.

Code of Federal Regulations, 2014 CFR

2014-01-01

... crewmember of a U.S.-registered civil aircraft shall, during takeoff and landing, keep his or her shoulder... at the crewmember's station is not equipped with a shoulder harness; or (2) The crewmember would be unable to perform required duties with the shoulder harness fastened. [Doc. No. 18334, 54 FR 34294, Aug...

Projectile Impact Effects on Aircraft Wire Harnesses

DTIC Science & Technology

1986-01-08

circuits Aircraft wire harnesses Modified ETFE Projectile damage and fires 19 ABSTRACT (Continue on reverse if necessary and identit) by block number...Tile Firifinr~ari~ne An overview of tile test fiririý raný,e is shown in Figure b. In tile for-eyrouria is tre rifle, witzh stock removed, utor iuyo e

77 FR 33125 - Airworthiness Directives; Bombardier, Inc. Airplanes

Federal Register 2010, 2011, 2012, 2013, 2014

2012-06-05

... along the wing leading edge and the inboard end rib of the wing leading edge due to insufficient clearance. This proposed AD would require inspecting the wire harness along the leading edge for chafing... to detect and correct chafing damage to the wire harness along the wing leading edge which, if not...

Harnessing the power of big data: infusing the scientific method with machine learning to transform ecology

USDA-ARS?s Scientific Manuscript database

Most efforts to harness the power of big data for ecology and environmental sciences focus on data and metadata sharing, standardization, and accuracy. However, many scientists have not accepted the data deluge as an integral part of their research because the current scientific method is not scalab...

Accelerations and Passenger Harness Loads Measured in Full-Scale Light-Airplane Crashes

NASA Technical Reports Server (NTRS)

Eiband, A. Martin; Simpkinson, Scott H.; Black, Dugald O.

1953-01-01

Full-scale light-airplane crashes simulating stall-spin accidents were conducted to determine the decelerations to which occupants are exposed and the resulting harness forces encountered in this type of accident. Crashes at impact speeds from 42 to 60 miles per hour were studied. The airplanes used were of the familiar steel-tube, fabric-covered, tandem, two-seat type. In crashes up to an impact speed of 60 miles per hour, crumpling of the forward fuselage structure prevented the maximum deceleration at the rear-seat location from exceeding 26 to 33g. This maximum g value appeared independent of the impact speed. Restraining forces in the seatbelt - shoulder-harness combination reached 5800 pounds. The rear-seat occupant can survive crashes of the type studied at impact speeds up to 60 miles per hour, if body movement is restrained by an adequate seatbelt-shoulder-harness combination so as to prevent injurious contact with obstacles normally present in the cabin. Inwardly collapsing cabin structure, however, is a potential hazard in the higher-speed crashes.

Effects of Caudal Elevation on Testicular Function in Rats: Separation of Effects on Spermatogenesis and Steroidogenesis

NASA Technical Reports Server (NTRS)

Deaver, D. R.; Amann, R. P.; Hammerstedt, R. H.; Ball, R.; Veeramachaneni, D. N. R.; Musacchia, X. J.

1992-01-01

A variety of biologic processes are perturbed when exposed to microgravity (space flight) for more than 7 days, including testicular function. Suspension of rats in a special harness (caudal elevation) to induce thoracic pooling of blood fluids and remove the support function of the hind limbs is used to mimic, on earth, the effects of microgravity encountered during space flight. Typically, this induces cryptorchidism in male rats. Three experiments were conducted to differentiate the effects of caudal elevation (30 deg angle) and anatomic location of testes on spermatogenesis and steroidogenesis. Rats were subjected to caudal elevation for 7 days using either a tail harness or a whole-body harness. Testes of rats fell into the abdominal cavity when a tail harness was used, but ligation of the iguinal canal prevented this repositioning. For rats with abdominal testes, testicular weight was reduced (P less than 0.05) and histology of testes was abnormal; the number of spermatids per gram parenchyma was lower (P less than 0.05) in tail-suspended rats compared with control rats.

P wave dispersion in patients with hypochondriasis.

PubMed

Atmaca, Murad; Korkmaz, Hasan; Korkmaz, Sevda

2010-11-26

P wave dispersion (Pd), defined as the difference between the maximum and the minimum P wave duration, has been associated with anxiety. Thus, we wondered whether Pd in hypochondriasis which is associated with anxiety differed from that in healthy controls. Pd was measured in 30 hypochondriac patients and same number of physically and mentally healthy age- and gender-matched controls. Hamilton Depression Rating (HDRS) and Hamilton Anxiety Rating Scales (HARS) were scored. The heart rate and left atrium (LA) sizes were not significantly different between groups. However, both Pmax and Pmin values of the patients were significantly higher than those of healthy controls. As for the main variable investigated in the present study, the corrected Pd was significantly longer in the patient group compared to control group. On the basis of this study, we can conclude that Pd may be related to hypochondriasis though our sample is too small to allow us to obtain a clear conclusion. Future studies with larger sample evaluating the effects of treatment are required. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Active Surfaces and Interfaces of Soft Materials

NASA Astrophysics Data System (ADS)

Wang, Qiming

A variety of intriguing surface patterns have been observed on developing natural systems, ranging from corrugated surface of white blood cells at nanometer scales to wrinkled dog skins at millimeter scales. To mimetically harness functionalities of natural morphologies, artificial transformative skin systems by using soft active materials have been rationally designed to generate versatile patterns for a variety of engineering applications. The study of the mechanics and design of these dynamic surface patterns on soft active materials are both physically interesting and technologically important. This dissertation starts with studying abundant surface patterns in Nature by constructing a unified phase diagram of surface instabilities on soft materials with minimum numbers of physical parameters. Guided by this integrated phase diagram, an electroactive system is designed to investigate a variety of electrically-induced surface instabilities of elastomers, including electro-creasing, electro-cratering, electro-wrinkling and electro-cavitation. Combing experimental, theoretical and computational methods, the initiation, evolution and transition of these instabilities are analyzed. To apply these dynamic surface instabilities to serving engineering and biology, new techniques of Dynamic Electrostatic Lithography and electroactive anti-biofouling are demonstrated.

A cost-effective method for femoral head allograft procurement for spinal arthrodesis: an alternative to commercially available allograft.

PubMed

Brown, Desmond A; Mallory, Grant W; Higgins, Dominique M; Abdulaziz, Mohammed; Huddleston, Paul M; Nassr, Ahmad; Fogelson, Jeremy L; Clarke, Michelle J

2014-07-01

A cost-effective procurement process for harvesting, storing, and using femoral head allografts is described. A brief review of the literature on the use of these allografts and a discussion of costs are provided. To describe a cost-effective method for the harvesting, storage, and use of femoral heads from patients undergoing total hip arthroplasty at our institution as a source of allograft bone. Spine fusion surgery uses a large proportion of commercially available bone grafts and bone substitutes. As the number of such surgical procedures performed in the United States continues to rise, these materials are at a historically high level of demand, which is projected to continue. Iliac crest bone autograft has historically been the standard of care, although this may be losing favor due to potential donor site morbidity. Although many substitutes are effective in promoting arthrodesis, their use is limited because of cost. Femoral heads are harvested under sterile conditions during total hip arthroplasty. The patient is tested per Food and Drug Administration regulations, and the tissue sample is cultured. The tissue is frozen and quarantined for a 6-month minimum pending repeat testing of donors and subsequently released for use. The relative cost-effectiveness of this tissue as a source of allograft bone is discussed. The average femoral head allograft is 54 to 56 mm in diameter and yields 50 cm of bone graft, with an average cost of US $435 for processing of the tissue resulting in a cost of US $8.70 per cm of allograft produced. Average production costs are significantly lower than those for other commonly available commercial bone grafts and substitutes. Femoral head allograft is a cost-effective alternative to commercially available allografts and bone substitutes. The method of procurement, storage, and use described could be adopted by other institutions in an effort to mitigate cost and increase supply. N/A.

Small head circumference at birth and early age at adiposity rebound.

PubMed

Eriksson, J G; Kajantie, E; Lampl, M; Osmond, C; Barker, D J P

2014-01-01

The adiposity rebound is the age in childhood when body mass index is at a minimum before increasing again. The age at rebound is highly variable. An early age is associated with increased obesity in later childhood and adult life. We have reported that an early rebound is predicted by low weight gain between birth and 1 year of age and resulting low body mass index at 1 year. Here, we examine whether age at adiposity rebound is determined by influences during infancy or is a consequence of foetal growth. Our hypothesis was that measurements of body size at birth are related to age at adiposity rebound. Longitudinal study of 2877 children born in Helsinki, Finland, during 1934-1944. Early age at adiposity rebound was associated with small head circumference and biparietal diameter at birth, but not with other measurements of body size at birth. The mean age at adiposity rebound rose from 5.8 years in babies with a head circumference of ≤33 cm to 6.2 in babies with a head circumference of >36 cm (P for trend = 0.007). The association between thinness in infancy and early rebound became apparent at 6 months of age. It was not associated with adverse living conditions. In a simultaneous regression, small head circumference at birth, high mother's body mass index and tall maternal stature each had statistically significant trends with early adiposity rebound (P = 0.002, <0.001, 0.004). We hypothesize that the small head size at birth that preceded an early adiposity rebound was the result of inability to sustain a rapid intra-uterine growth trajectory initiated in association with large maternal body size. This was followed by catch-up growth in infancy, and we hypothesize that this depleted the infant's fat stores. © 2013 Scandinavian Physiological Society. Published by John Wiley & Sons Ltd.

Many human accelerated regions are developmental enhancers

PubMed Central

Capra, John A.; Erwin, Genevieve D.; McKinsey, Gabriel; Rubenstein, John L. R.; Pollard, Katherine S.

2013-01-01

The genetic changes underlying the dramatic differences in form and function between humans and other primates are largely unknown, although it is clear that gene regulatory changes play an important role. To identify regulatory sequences with potentially human-specific functions, we and others used comparative genomics to find non-coding regions conserved across mammals that have acquired many sequence changes in humans since divergence from chimpanzees. These regions are good candidates for performing human-specific regulatory functions. Here, we analysed the DNA sequence, evolutionary history, histone modifications, chromatin state and transcription factor (TF) binding sites of a combined set of 2649 non-coding human accelerated regions (ncHARs) and predicted that at least 30% of them function as developmental enhancers. We prioritized the predicted ncHAR enhancers using analysis of TF binding site gain and loss, along with the functional annotations and expression patterns of nearby genes. We then tested both the human and chimpanzee sequence for 29 ncHARs in transgenic mice, and found 24 novel developmental enhancers active in both species, 17 of which had very consistent patterns of activity in specific embryonic tissues. Of these ncHAR enhancers, five drove expression patterns suggestive of different activity for the human and chimpanzee sequence at embryonic day 11.5. The changes to human non-coding DNA in these ncHAR enhancers may modify the complex patterns of gene expression necessary for proper development in a human-specific manner and are thus promising candidates for understanding the genetic basis of human-specific biology. PMID:24218637

Hepatic Artery Resection for Bismuth Type III and IV Hilar Cholangiocarcinoma: Is Reconstruction Always Required?

PubMed

Hu, Hai-Jie; Jin, Yan-Wen; Zhou, Rong-Xing; Shrestha, Anuj; Ma, Wen-Jie; Yang, Qin; Wang, Jun-Ke; Liu, Fei; Cheng, Nan-Sheng; Li, Fu-Yu

2018-03-06

The objective of the study is to examine the feasibility of hepatic artery resection (HAR) without subsequent reconstruction (RCS) in specified patients of Bismuth type III and IV hilar cholangiocarcinoma. We retrospectively reviewed 63 patients who underwent hepatic artery resection for Bismuth type III and IV hilar cholangiocarcinoma. These patients were subsequently enrolled into two groups based on whether the artery reconstruction was conducted. Postoperative morbidity and mortality, and long-term survival outcome were compared between the two groups. There were 29 patients in HAR group and 34 patients in the HAR + RCS group. Patients with hepatic artery reconstruction tended to have longer operative time (545.6 ± 143.1 min vs. 656.3 ± 192.8 min; P = 0.013) and smaller tumor size (3.0 ± 1.1 cm vs. 2.5 ± 0.9 cm; P = 0.036). The R0 resection margin was comparable between the HAR group and HAR + RCS group (86.2 vs. 85.3%; P > 0.05). Twelve patients (41.4%) with 24 complications in HAR group and 13 patients (38.2%) with 25 complications in HAR + RCS group were recorded (P = 0.799). The postoperative hepatic failure rate (13.8 vs. 5.9%) and postoperative mortality rate (3.4% vs. 2.9%) were also comparable between the two groups. In the HAR group, the overall 1-, 3-, and 5-year survival rates were 72, 41, and 19%, respectively; while in the HAR + RCS group, the overall 1-, 3-, and 5-year survival rates were 79, 45, and 25%, respectively (P = 0.928). Hepatic artery resection without reconstruction is also a safe and feasible surgical procedure for highly selected cases of Bismuth type III and IV hilar cholangiocarcinoma.

High Speed Link Radiated Emission Reduction

NASA Astrophysics Data System (ADS)

Bisognin, P.; Pelissou, P.; Cissou, R.; Giniaux, M.; Vargas, O.

2016-05-01

To control the radiated emission of high-speed link and associated unit, the current approach is to implement overall harness shielding on cables bundles. This method is very efficient in the HF/ VHF (high frequency/ very high frequency) and UHF (ultra-high frequency) ranges when the overall harness shielding is properly bonded on EMC back-shell. Unfortunately, with the increasing frequency, the associated half wavelength matches with the size of Sub-D connector that is the case for the L band. Therefore, the unit connectors become the main source of interference emission. For the L-band and S-band, the current technology of EMC back-shell leaves thin aperture matched with the L band half wavelength and therefore, the shielding effectiveness is drastically reduced. In addition, overall harness shielding means significant increases of the harness mass.Airbus D&S Toulouse and Elancourt investigated a new solution to avoid the need of overall harness shielding. The objective is to procure EM (Electro-Magnetic) clean unit connected to cables bundles free of any overall harness shielding. The proposed solution is to implement EMC common mode filtering on signal interfaces directly on unit PCB as close as possible the unit connector.Airbus D&S Elancourt designed and manufactured eight mock-ups of LVDS (Low Voltage Differential Signaling) interface PCBs' with different solutions of filtering. After verification of the signal integrity, three mock-ups were retained (RC filter and two common mode choke coil) in addition to the reference one (without EMC filter).Airbus D&S Toulouse manufactured associated LVDS cable bundles and integrated the RX (Receiver) and TX (Transmitter) LVDS boards in shielded boxes.Then Airbus D&S performed radiated emission measurement of the LVDS links subassemblies (e.g. RX and TX boxes linked by LVDS cables) according to the standard test method. This paper presents the different tested solutions and main conclusions on the feasibility of such approach.