Browns Ferry Nuclear Plant Unit 2: Control rod drive scram discharge headers decontamination effort

DOE Office of Scientific and Technical Information (OSTI.GOV)

Traynor, J.C.

1983-08-01

The control rod drive (CRD) scram discharge headers were decontaminated during the Browns Ferry unit 2, cycle 4 refueling outage (August 2-5, 1982). Hydrolasing (high-pressure water blasting) was used as the method of decontamination to remove fixed and loose radioactive contaminants from the headers. It was found that hydrolasing of the west scram discharge headers resulted in approximate maximum and average decontamination factors (DFs) on contact of 13 and 5, respectively. For the east scram discharge headers, hydrolasing resulted in a maximum and average DF on contact of approximately 3. The maximum and average DFs on contact for the individualmore » headers ranged from 1 to 33 and 1 to 10, respectively, while the walkway (head-level) DFs were in the range of 3 to 4. Higher DFs were impeded by inadequate drainage and backwashing of fluid. This led to increased radiation levels in some areas and recontamination of adjacent headers.« less

On Applicability of Network Coding Technique for 6LoWPAN-based Sensor Networks.

PubMed

Amanowicz, Marek; Krygier, Jaroslaw

2018-05-26

In this paper, the applicability of the network coding technique in 6LoWPAN-based sensor multihop networks is examined. The 6LoWPAN is one of the standards proposed for the Internet of Things architecture. Thus, we can expect the significant growth of traffic in such networks, which can lead to overload and decrease in the sensor network lifetime. The authors propose the inter-session network coding mechanism that can be implemented in resource-limited sensor motes. The solution reduces the overall traffic in the network, and in consequence, the energy consumption is decreased. Used procedures take into account deep header compressions of the native 6LoWPAN packets and the hop-by-hop changes of the header structure. Applied simplifications reduce signaling traffic that is typically occurring in network coding deployments, keeping the solution usefulness for the wireless sensor networks with limited resources. The authors validate the proposed procedures in terms of end-to-end packet delay, packet loss ratio, traffic in the air, total energy consumption, and network lifetime. The solution has been tested in a real wireless sensor network. The results confirm the efficiency of the proposed technique, mostly in delay-tolerant sensor networks.

Block selective redaction for minimizing loss during de-identification of burned in text in irreversibly compressed JPEG medical images.

PubMed

Clunie, David A; Gebow, Dan

2015-01-01

Deidentification of medical images requires attention to both header information as well as the pixel data itself, in which burned-in text may be present. If the pixel data to be deidentified is stored in a compressed form, traditionally it is decompressed, identifying text is redacted, and if necessary, pixel data are recompressed. Decompression without recompression may result in images of excessive or intractable size. Recompression with an irreversible scheme is undesirable because it may cause additional loss in the diagnostically relevant regions of the images. The irreversible (lossy) JPEG compression scheme works on small blocks of the image independently, hence, redaction can selectively be confined only to those blocks containing identifying text, leaving all other blocks unchanged. An open source implementation of selective redaction and a demonstration of its applicability to multiframe color ultrasound images is described. The process can be applied either to standalone JPEG images or JPEG bit streams encapsulated in other formats, which in the case of medical images, is usually DICOM.

Error mitigation for CCSD compressed imager data

NASA Astrophysics Data System (ADS)

Gladkova, Irina; Grossberg, Michael; Gottipati, Srikanth; Shahriar, Fazlul; Bonev, George

2009-08-01

To efficiently use the limited bandwidth available on the downlink from satellite to ground station, imager data is usually compressed before transmission. Transmission introduces unavoidable errors, which are only partially removed by forward error correction and packetization. In the case of the commonly used CCSD Rice-based compression, it results in a contiguous sequence of dummy values along scan lines in a band of the imager data. We have developed a method capable of using the image statistics to provide a principled estimate of the missing data. Our method outperforms interpolation yet can be performed fast enough to provide uninterrupted data flow. The estimation of the lost data provides significant value to end users who may use only part of the data, may not have statistical tools, or lack the expertise to mitigate the impact of the lost data. Since the locations of the lost data will be clearly marked as meta-data in the HDF or NetCDF header, experts who prefer to handle error mitigation themselves will be free to use or ignore our estimates as they see fit.

Foetal exposure to Panax ginseng extract reverts the effects of prenatal dexamethasone in the synthesis of testosterone by Leydig cells of the adult rat.

PubMed

Wanderley, Maria I; Saraiva, Karina L A; César Vieira, Juliany S B; Peixoto, Christina A; Udrisar, Daniel P

2013-06-01

The aim of this study was to examine the effect of maternal exposure to Panax ginseng extract (GE) on the prenatal dexamethasone (DEXA)-induced increase in testosterone production by isolated Leydig cells in adult rats. Pregnant rats were treated with (i) GE (200 mg/kg) or vehicle on days 10-21; (ii) DEXA (100 μg/kg) or vehicle on days 14-21; or (iii) a combination of GE plus DEXA at the same doses and with the same regimen. Testosterone production was induced either by the activator of protein kinase A (dbcAMP) or substrates of steroidogenesis [22(R)-hydroxycholesterol (22(R)-OH-C)] and pregnenolone. The capacity of rat Leydig cells exposed to DEXA to synthesize testosterone induced by dbcAMP, 22(R)-OH-C or pregnenolone was increased in comparison with the control group. Combined exposure to DEXA + GE prevented the effect of DEXA on the responsiveness of Leydig cells to all inductors of testosterone synthesis, whereas GE alone did not modify the response to inductors. No modifications in testosterone production were observed under basal conditions. StAR immunoexpression in Leydig cells was not modified by prenatal exposure to DEXA, GE or DEXA + GE. P450scc and glucocorticoid receptor immunoexpression was higher in offspring exposed to DEXA in comparison with the control group. This increased expression was prevented by combined treatment with DEXA + GE. The present findings demonstrate that GE is capable of reversing the effect of DEXA on testosterone synthesis by rat Leydig cells. © 2013 The Authors. International Journal of Experimental Pathology © 2013 International Journal of Experimental Pathology.

Improved Air-Treatment Canister

NASA Technical Reports Server (NTRS)

Boehm, A. M.

1982-01-01

Proposed air-treatment canister integrates a heater-in-tube water evaporator into canister header. Improved design prevents water from condensing and contaminating chemicals that regenerate the air. Heater is evenly spiraled about the inlet header on the canister. Evaporator is brazed to the header.

DDN (Defense Data Network) Protocol Handbook. Volume 2. DARPA Internet Protocols

DTIC Science & Technology

1985-12-01

header padding is used to ensure that the internet header ends on a 32 bit boundary. The padding is zero . 3.2. Discussion The implementation of a... zeros . The first of these would be interpreted as the end-of-options option, and the remainder as internet header padding , Every internet module must...several octets in length. The internet header Padding field is used to ensure that the data begins on 32 bit word boundary. The padding is zero

Clustering header categories extracted from web tables

NASA Astrophysics Data System (ADS)

Nagy, George; Embley, David W.; Krishnamoorthy, Mukkai; Seth, Sharad

2015-01-01

Revealing related content among heterogeneous web tables is part of our long term objective of formulating queries over multiple sources of information. Two hundred HTML tables from institutional web sites are segmented and each table cell is classified according to the fundamental indexing property of row and column headers. The categories that correspond to the multi-dimensional data cube view of a table are extracted by factoring the (often multi-row/column) headers. To reveal commonalities between tables from diverse sources, the Jaccard distances between pairs of category headers (and also table titles) are computed. We show how about one third of our heterogeneous collection can be clustered into a dozen groups that exhibit table-title and header similarities that can be exploited for queries.

ONE MILLION GALLON WATER TANK, PUMP HEADER PIPE (AT LEFT), ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

ONE MILLION GALLON WATER TANK, PUMP HEADER PIPE (AT LEFT), HEADER BYPASS PIPE (AT RIGHT), AND PUMPHOUSE FOUNDATIONS. Looking northeast - Edwards Air Force Base, Air Force Rocket Propulsion Laboratory, Flame Deflector Water System, Test Area 1-120, north end of Jupiter Boulevard, Boron, Kern County, CA

High pressure ceramic heat exchanger

DOEpatents

Harkins, Bruce D.; Ward, Michael E.

1998-01-01

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

High pressure ceramic heat exchanger

DOEpatents

Harkins, Bruce D.; Ward, Michael E.

1999-01-01

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the reinforcing member and having a strengthening member wrapped around the refractory material. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures.

High pressure ceramic heat exchanger

DOEpatents

Harkins, B.D.; Ward, M.E.

1998-09-22

Many recuperators have components which react to corrosive gases and are used in applications where the donor fluid includes highly corrosive gases. These recuperators have suffered reduced life, increased service or maintenance, and resulted in increased cost. The present header assembly when used with recuperators reduces the brittle effect of a portion of the ceramic components. Thus, the present header assembly used with the present recuperator increases the life, reduces the service and maintenance, and reduces the increased cost associated with corrosive action of components used to manufacture recuperators. The present header assembly is comprised of a first ceramic member, a second ceramic member, a strengthening reinforcing member being in spaced relationship to the first ceramic member and the second ceramic member. The header assembly is further comprised of a refractory material disposed in contacting relationship with the first ceramic member, the second ceramic member and the strengthening reinforcing member. The present header assembly provides a high strength load bearing header assembly having good thermal cycling characteristics, good resistance to a corrosive environment and good steady state strength at elevated temperatures. 5 figs.

Codestream-Based Identification of JPEG 2000 Images with Different Coding Parameters

NASA Astrophysics Data System (ADS)

Watanabe, Osamu; Fukuhara, Takahiro; Kiya, Hitoshi

A method of identifying JPEG 2000 images with different coding parameters, such as code-block sizes, quantization-step sizes, and resolution levels, is presented. It does not produce false-negative matches regardless of different coding parameters (compression rate, code-block size, and discrete wavelet transform (DWT) resolutions levels) or quantization step sizes. This feature is not provided by conventional methods. Moreover, the proposed approach is fast because it uses the number of zero-bit-planes that can be extracted from the JPEG 2000 codestream by only parsing the header information without embedded block coding with optimized truncation (EBCOT) decoding. The experimental results revealed the effectiveness of image identification based on the new method.

Notes on Operations. The Documentation of Electronic Texts Using Text Encoding Initiative Headers: An Introduction.

ERIC Educational Resources Information Center

Giordano, Richard

1994-01-01

Describes the Text Encoding Initiative (TEI) project and the TEI header, which documents electronic text in a standard interchange format understandable to both librarian catalogers and nonlibrarian text encoders. The form and function of the TEI header is introduced, and its relationship to the MARC record is explained. (10 references) (KRN)

--No Title--

Science.gov Websites

a#show-docs-search{display:inline;padding-left:2%}div.popover span{display:block}div.popover %}p.pub-note span{font-style:italic;padding-bottom:10px}#category-search input[type=submit]{margin-top :100px;margin-left:90px}div#search-header{padding:0 0 20px 0}div#search-header span.header{font-size

Phishtest: Measuring the Impact of Email Headers on the Predictive Accuracy of Machine Learning Techniques

ERIC Educational Resources Information Center

Tout, Hicham

2013-01-01

The majority of documented phishing attacks have been carried by email, yet few studies have measured the impact of email headers on the predictive accuracy of machine learning techniques in detecting email phishing attacks. Research has shown that the inclusion of a limited subset of email headers as features in training machine learning…

Excalibur Strategic Configured Load (SCL) for the Heavy Expanded Mobility Tactical Truck (HEMTT). Testing IAW TP-94-01, Revision 2, June 2004, Transportability Testing Procedures

DTIC Science & Technology

2008-06-01

2-1 PART 3 - TEST EQUIPMENT 1. Semitrailer, flatbed , breakbulk/container transporter, 34 ton Model #: M872A1 Manufactured by Heller Truck Body... LAMINATING DUNNAGE. ADDITIONALLY, THE NAILING PATTERN FOR AN UP- DA39 PALLET UNITS CENTERED ON TOP OF PRIOR DA39 PALLET UNITS, PER PIECE OF LAMINATED ...ai FT (APPWO HEADER I" X V’ X 7-4- (AS RECID, 1 SHOWYN). LAMINATE EACH HEADER TO PREVIOUS HEADER W/9-10d NAILS. HEADER 2" x 8" x r-" (AS RECID, 3 SHOWN

Secured Hash Based Burst Header Authentication Design for Optical Burst Switched Networks

NASA Astrophysics Data System (ADS)

Balamurugan, A. M.; Sivasubramanian, A.; Parvathavarthini, B.

2017-12-01

The optical burst switching (OBS) is a promising technology that could meet the fast growing network demand. They are featured with the ability to meet the bandwidth requirement of applications that demand intensive bandwidth. OBS proves to be a satisfactory technology to tackle the huge bandwidth constraints, but suffers from security vulnerabilities. The objective of this proposed work is to design a faster and efficient burst header authentication algorithm for core nodes. There are two important key features in this work, viz., header encryption and authentication. Since the burst header is an important in optical burst switched network, it has to be encrypted; otherwise it is be prone to attack. The proposed MD5&RC4-4S based burst header authentication algorithm runs 20.75 ns faster than the conventional algorithms. The modification suggested in the proposed RC4-4S algorithm gives a better security and solves the correlation problems between the publicly known outputs during key generation phase. The modified MD5 recommended in this work provides 7.81 % better avalanche effect than the conventional algorithm. The device utilization result also shows the suitability of the proposed algorithm for header authentication in real time applications.

Simple online recognition of optical data strings based on conservative optical logic

NASA Astrophysics Data System (ADS)

Caulfield, H. John; Shamir, Joseph; Zavalin, Andrey I.; Silberman, Enrique; Qian, Lei; Vikram, Chandra S.

2006-06-01

Optical packet switching relies on the ability of a system to recognize header information on an optical signal. Unless the headers are very short with large Hamming distances, optical correlation fails and optical logic becomes attractive because it can handle long headers with Hamming distances as low as 1. Unfortunately, the only optical logic gates fast enough to keep up with current communication speeds involve semiconductor optical amplifiers and do not lend themselves to the incorporation of large numbers of elements for header recognition and would consume a lot of power as well. The ideal system would operate at any bandwidth with no power consumption. We describe how to design and build such a system by using passive optical logic. This too leads to practical problems that we discuss. We show theoretically various ways to use optical interferometric logic for reliable recognition of long data streams such as headers in optical communication. In addition, we demonstrate one particularly simple experimental approach using interferometric coinc gates.

Thermal shock testing for assuring reliability of glass-sealed microelectronic packages

NASA Technical Reports Server (NTRS)

Thomas, Walter B., III; Lewis, Michael D.

1991-01-01

Tests were performed to determine if thermal shocking is destructive to glass-to-metal seal microelectronic packages and if thermal shock step stressing can compare package reliabilities. Thermal shocking was shown to be not destructive to highly reliable glass seals. Pin-pull tests used to compare the interfacial pin glass strengths showed no differences between thermal shocked and not-thermal shocked headers. A 'critical stress resistance temperature' was not exhibited by the 14 pin Dual In-line Package (DIP) headers evaluated. Headers manufactured in cryogenic nitrogen based and exothermically generated atmospheres showed differences in as-received leak rates, residual oxide depths and pin glass interfacial strengths; these were caused by the different manufacturing methods, in particular, by the chemically etched pins used by one manufacturer. Both header types passed thermal shock tests to temperature differentials of 646 C. The sensitivity of helium leak rate measurements was improved up to 70 percent by baking headers for two hours at 200 C after thermal shocking.

Recognition of the optical packet header for two channels utilizing the parallel reservoir computing based on a semiconductor ring laser

NASA Astrophysics Data System (ADS)

Bao, Xiurong; Zhao, Qingchun; Yin, Hongxi; Qin, Jie

2018-05-01

In this paper, an all-optical parallel reservoir computing (RC) system with two channels for the optical packet header recognition is proposed and simulated, which is based on a semiconductor ring laser (SRL) with the characteristic of bidirectional light paths. The parallel optical loops are built through the cross-feedback of the bidirectional light paths where every optical loop can independently recognize each injected optical packet header. Two input signals are mapped and recognized simultaneously by training all-optical parallel reservoir, which is attributed to the nonlinear states in the laser. The recognition of optical packet headers for two channels from 4 bits to 32 bits is implemented through the simulation optimizing system parameters and therefore, the optimal recognition error ratio is 0. Since this structure can combine with the wavelength division multiplexing (WDM) optical packet switching network, the wavelength of each channel of optical packet headers for recognition can be different, and a better recognition result can be obtained.

MER Telemetry Processor

NASA Technical Reports Server (NTRS)

Lee, Hyun H.

2012-01-01

MERTELEMPROC processes telemetered data in data product format and generates Experiment Data Records (EDRs) for many instruments (HAZCAM, NAVCAM, PANCAM, microscopic imager, Moessbauer spectrometer, APXS, RAT, and EDLCAM) on the Mars Exploration Rover (MER). If the data is compressed, then MERTELEMPROC decompresses the data with an appropriate decompression algorithm. There are two compression algorithms (ICER and LOCO) used in MER. This program fulfills a MER specific need to generate Level 1 products within a 60-second time requirement. EDRs generated by this program are used by merinverter, marscahv, marsrad, and marsjplstereo to generate higher-level products for the mission operations. MERTELEPROC was the first GDS program to process the data product. Metadata of the data product is in XML format. The software allows user-configurable input parameters, per-product processing (not streambased processing), and fail-over is allowed if the leading image header is corrupted. It is used within the MER automated pipeline. MERTELEMPROC is part of the OPGS (Operational Product Generation Subsystem) automated pipeline, which analyzes images returned by in situ spacecraft and creates level 1 products to assist in operations, science, and outreach.

Multi-protocol header generation system

DOE Office of Scientific and Technical Information (OSTI.GOV)

Roberts, David A.; Ignatowski, Michael; Jayasena, Nuwan

A communication device includes a data source that generates data for transmission over a bus, and a data encoder that receives and encodes outgoing data. An encoder system receives outgoing data from a data source and stores the outgoing data in a first queue. An encoder encodes outgoing data with a header type that is based upon a header type indication from a controller and stores the encoded data that may be a packet or a data word with at least one layered header in a second queue for transmission. The device is configured to receive at a payload extractor,more » a packet protocol change command from the controller and to remove the encoded data and to re-encode the data to create a re-encoded data packet and placing the re-encoded data packet in the second queue for transmission.« less

Coal slurry fuel supply and purge system

DOEpatents

McDowell, Robert E.; Basic, Steven L.; Smith, Russel M.

1994-01-01

A coal slurry fuel supply and purge system for a locomotive engines is disclosed which includes a slurry recirculation path, a stand-by path for circulating slurry during idle or states of the engine when slurry fuel in not required by the engine, and an engine header fluid path connected to the stand-by path, for supplying and purging slurry fuel to and from fuel injectors. A controller controls the actuation of valves to facilitate supply and purge of slurry to and from the fuel injectors. A method for supplying and purging coal slurry in a compression ignition engine is disclosed which includes controlling fluid flow devices and valves in a plurality of fluid paths to facilitate continuous slurry recirculation and supply and purge of or slurry based on the operating state of the engine.

Providing integrity, authenticity, and confidentiality for header and pixel data of DICOM images.

PubMed

Al-Haj, Ali

2015-04-01

Exchange of medical images over public networks is subjected to different types of security threats. This has triggered persisting demands for secured telemedicine implementations that will provide confidentiality, authenticity, and integrity for the transmitted images. The medical image exchange standard (DICOM) offers mechanisms to provide confidentiality for the header data of the image but not for the pixel data. On the other hand, it offers mechanisms to achieve authenticity and integrity for the pixel data but not for the header data. In this paper, we propose a crypto-based algorithm that provides confidentially, authenticity, and integrity for the pixel data, as well as for the header data. This is achieved by applying strong cryptographic primitives utilizing internally generated security data, such as encryption keys, hashing codes, and digital signatures. The security data are generated internally from the header and the pixel data, thus a strong bond is established between the DICOM data and the corresponding security data. The proposed algorithm has been evaluated extensively using DICOM images of different modalities. Simulation experiments show that confidentiality, authenticity, and integrity have been achieved as reflected by the results we obtained for normalized correlation, entropy, PSNR, histogram analysis, and robustness.

Development and Evaluation of a Clinical Note Section Header Terminology

PubMed Central

Denny, Joshua C.; Miller, Randolph A.; Johnson, Kevin B.; Spickard, Anderson

2008-01-01

Clinical documentation is often expressed in natural language text, yet providers often use common organizations that segment these notes in sections, such as “history of present illness” or “physical examination.” We developed a hierarchical section header terminology, supporting mappings to LOINC and other vocabularies; it contained 1109 concepts and 4332 synonyms. Physicians evaluated it compared to LOINC and the Evaluation and Management billing schema using a randomly selected corpus of history and physical notes. Evaluated documents contained a median of 54 sections and 27 “major sections.” There were 16,196 total sections in the evaluation note corpus. The terminology contained 99.9% of the clinical sections; LOINC matched 77% of section header concepts and 20% of section header strings in those documents. The section terminology may enable better clinical note understanding and interoperability. Future development and integration into natural language processing systems is needed. PMID:18999303

Method and apparatus for eliminating unsuccessful tries in a search tree

NASA Technical Reports Server (NTRS)

Peterson, John C. (Inventor); Chow, Edward (Inventor); Madan, Herb S. (Inventor)

1991-01-01

A circuit switching system in an M-ary, n-cube connected network completes a best-first path from an originating node to a destination node by latching valid legs of the path as the path is being sought out. Each network node is provided with a routing hyperswitch sub-network, (HSN) connected between that node and bidirectional high capacity communication channels of the n-cube network. The sub-networks are all controlled by routing algorithms which respond to message identification headings (headers) on messages to be routed along one or more routing legs. The header includes information embedded therein which is interpreted by each sub-network to route and historically update the header. A logic circuit, available at every node, implements the algorithm and automatically forwards or back-tracks the header in the network legs of various paths until a completed path is latched.

LAMP Educational Site

Science.gov Websites

topHeader GSFC NASA SwRI Denver Museum of Nature and Science sub header Home Science and the ready to go back to the Moon? NASA took the first step in that direction in 2009 with the launch of

Non-parametric adaptative JPEG fragments carving

NASA Astrophysics Data System (ADS)

Amrouche, Sabrina Cherifa; Salamani, Dalila

2018-04-01

The most challenging JPEG recovery tasks arise when the file header is missing. In this paper we propose to use a two layer machine learning model to restore headerless JPEG images. We first build a classifier able to identify the structural properties of the images/fragments and then use an AutoEncoder (AE) to learn the fragment features for the header prediction. We define a JPEG universal header and the remaining free image parameters (Height, Width) are predicted with a Gradient Boosting Classifier. Our approach resulted in 90% accuracy using the manually defined features and 78% accuracy using the AE features.

XS: a FASTQ read simulator.

PubMed

Pratas, Diogo; Pinho, Armando J; Rodrigues, João M O S

2014-01-16

The emerging next-generation sequencing (NGS) is bringing, besides the natural huge amounts of data, an avalanche of new specialized tools (for analysis, compression, alignment, among others) and large public and private network infrastructures. Therefore, a direct necessity of specific simulation tools for testing and benchmarking is rising, such as a flexible and portable FASTQ read simulator, without the need of a reference sequence, yet correctly prepared for producing approximately the same characteristics as real data. We present XS, a skilled FASTQ read simulation tool, flexible, portable (does not need a reference sequence) and tunable in terms of sequence complexity. It has several running modes, depending on the time and memory available, and is aimed at testing computing infrastructures, namely cloud computing of large-scale projects, and testing FASTQ compression algorithms. Moreover, XS offers the possibility of simulating the three main FASTQ components individually (headers, DNA sequences and quality-scores). XS provides an efficient and convenient method for fast simulation of FASTQ files, such as those from Ion Torrent (currently uncovered by other simulators), Roche-454, Illumina and ABI-SOLiD sequencing machines. This tool is publicly available at http://bioinformatics.ua.pt/software/xs/.

Fallon FORGE Well Lithologies

DOE Data Explorer

Doug Blankenship

2016-03-01

x,y,z text file of the downhole lithologic interpretations in the wells in and around the Fallon FORGE site. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

Monolithic exploding foil initiator

DOEpatents

Welle, Eric J; Vianco, Paul T; Headley, Paul S; Jarrell, Jason A; Garrity, J. Emmett; Shelton, Keegan P; Marley, Stephen K

2012-10-23

A monolithic exploding foil initiator (EFI) or slapper detonator and the method for making the monolithic EFI wherein the exploding bridge and the dielectric from which the flyer will be generated are integrated directly onto the header. In some embodiments, the barrel is directly integrated directly onto the header.

Asynchronous broadcast for ordered delivery between compute nodes in a parallel computing system where packet header space is limited

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Sameer

Disclosed is a mechanism on receiving processors in a parallel computing system for providing order to data packets received from a broadcast call and to distinguish data packets received at nodes from several incoming asynchronous broadcast messages where header space is limited. In the present invention, processors at lower leafs of a tree do not need to obtain a broadcast message by directly accessing the data in a root processor's buffer. Instead, each subsequent intermediate node's rank id information is squeezed into the software header of packet headers. In turn, the entire broadcast message is not transferred from the rootmore » processor to each processor in a communicator but instead is replicated on several intermediate nodes which then replicated the message to nodes in lower leafs. Hence, the intermediate compute nodes become "virtual root compute nodes" for the purpose of replicating the broadcast message to lower levels of a tree.« less

NIMBUS 7 Earth Radiation Budget (ERB) Matrix User's Guide. Volume 2: Tape Specifications

NASA Technical Reports Server (NTRS)

Ray, S. N.; Vasanth, K. L.

1984-01-01

The ERB MATRIX tape is generated by an IBM 3081 computer program and is a 9 track, 1600 BPI tape. The gross format of the tape given on Page 1, shows an initial standard header file followed by data files. The standard header file contains two standard header records. A trailing documentation file (TDF) is the last file on the tape. Pages 9 through 17 describe, in detail, the standard header file and the TDF. The data files contain data for 37 different ERB parameters. Each file has data based on either a daily, 6 day cyclic, or monthly time interval. There are three types of physical records in the data files; namely, the world grid physical record, the documentation mercator/polar map projection physical record, and the monthly calibration physical record. The manner in which the data for the 37 ERB parameters are stored in the physical records comprising the data files, is given in the gross format section.

Design of Boiler Welding for Improvement of Lifetime and Cost Control.

PubMed

Thong-On, Atcharawadi; Boonruang, Chatdanai

2016-11-03

Fe-2.25Cr-1Mo a widely used material for headers and steam tubes of boilers. Welding of steam tube to header is required for production of boiler. Heat affected zone of the weld can have poor mechanical properties and poor corrosion behavior leading to weld failure. The cost of material used for steam tube and header of boiler should be controlled. This study propose a new materials design for boiler welding to improve the lifetime and cost control, using tungsten inert gas (TIG) welding of Fe-2.25Cr-1Mo tube to carbon steel pipe with chromium-containing filler. The cost of production could be reduced by the use of low cost material such as carbon steel pipe for boiler header. The effect of chromium content on corrosion behavior of the weld was greater than that of the microstructure. The lifetime of the welded boiler can be increased by improvement of mechanical properties and corrosion behavior of the heat affected zone.

Design of Boiler Welding for Improvement of Lifetime and Cost Control

PubMed Central

Thong-On, Atcharawadi; Boonruang, Chatdanai

2016-01-01

Fe-2.25Cr-1Mo a widely used material for headers and steam tubes of boilers. Welding of steam tube to header is required for production of boiler. Heat affected zone of the weld can have poor mechanical properties and poor corrosion behavior leading to weld failure. The cost of material used for steam tube and header of boiler should be controlled. This study propose a new materials design for boiler welding to improve the lifetime and cost control, using tungsten inert gas (TIG) welding of Fe-2.25Cr-1Mo tube to carbon steel pipe with chromium-containing filler. The cost of production could be reduced by the use of low cost material such as carbon steel pipe for boiler header. The effect of chromium content on corrosion behavior of the weld was greater than that of the microstructure. The lifetime of the welded boiler can be increased by improvement of mechanical properties and corrosion behavior of the heat affected zone. PMID:28774014

Malfunction of subpectorally implanted cardiac resynchronization therapy defibrillators due to weakened header bond.

PubMed

Hayat, Sajad A; Kojodjojo, Pipin; Mason, Anthony; Benfield, Ann; Wright, Ian; Whinnett, Zachary; Lim, Phang Boon; Davies, D Wyn; Lefroy, David; Peters, Nicholas S; Kanagaratnam, Prapa

2013-03-01

Implantable cardioverter defibrillator (ICD) implantation has increased significantly over the last 10 years. Concerns about the safety and reliability of ICD systems have been raised, with premature lead failure and battery malfunctions accounting for the majority of reported adverse events. We describe the unique mode of presentation, diagnosis, and management of cardiac resynchronization therapy defibrillators (CRT-D) malfunctions that were caused by weakened bonding between the generator and header. Between June 2008 and December 2009, 22 Teligen™ ICDs and 24 Cognis™ CRT-Ds were implanted subpectorally at our institution, until a product advisory was issued. Of 24 Cognis™ CRT-D implants, 3 patients presented with CRT-D malfunctions. All our cases presented with initially intermittent and then persisting increases in shock lead impedance, associated with nonphysiological noise in the shock electrogram channels. These issues were rectified by generator change. Postexplant laboratory analysis confirmed inadequate bonding between device header and titanium casing in all cases, resulting in loosening and rocking of the header followed by fatigue-induced fracture of the shock circuitry. Weakened bonding between the header and generator casing of subpectorally implanted CRT-Ds can result in fractures and malfunction of the HV circuit. Physicians monitoring patients with devices affected by the product advisory should remain vigilant in order to diagnose and manage similar device malfunction expediently. © 2012 Wiley Periodicals, Inc.

Defense RDT&E Online System (DROLS) Handbook

DTIC Science & Technology

1993-07-01

of the descriptor TROPICAL DISEASES hierarchically will produce the same results as a cumulated search of the following terms: CHOLERA DENGUE ...Header List The Source header List is a two volume listing of all source names arranged in alphabetical order. Each en ~try consists of: Source Name...BB Belgium ................................................................ BE Belize

40 CFR 205.165 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... respect to the parameters listed in § 205.168 of this subpart. (2) Exhaust header pipe means any tube of... be “exhaust header pipes.” (3) Failing exhaust system means that, when installed on any Federally... EQUIPMENT NOISE EMISSION CONTROLS Motorcycle Exhaust Systems § 205.165 Definitions. (a) As used in this...

Large variable conductance heat pipe. Transverse header

NASA Technical Reports Server (NTRS)

Edelstein, F.

1975-01-01

The characteristics of gas-loaded, variable conductance heat pipes (VCHP) are discussed. The difficulties involved in developing a large VCHP header are analyzed. The construction of the large capacity VCHP is described. A research project to eliminate some of the problems involved in large capacity VCHP operation is explained.

Manifold to uniformly distribute a solid-liquid slurry

DOEpatents

Kern, Kenneth C.

1983-01-01

This invention features a manifold that divides a stream of coal particles and liquid into several smaller streams maintaining equal or nearly equal mass compositions. The manifold consists of a horizontal, variable area header having sharp-edged, right-angled take-offs which are oriented on the bottom of the header.

--No Title--

Science.gov Websites

NREL TRANSPORTATION stylesheet*/ .content-list-widget .header-box .title { color: #fff; } .content -list-widget .header-box { background-color: #0079C2; border-bottom: 5px solid #00A4E4 ) ************************************************************/ .greybg { background-color: #E3E6E8; } .hide-bullets { list-style:none; margin-left: -40px; margin-top

Microchannel laminated mass exchanger and method of making

DOEpatents

Martin, Peter M [Kennewick, WA; Bennett, Wendy D [Kennewick, WA; Matson, Dean W [Kennewick, WA; Stewart, Donald C [Richland, WA; Drost, Monte K [Pasco, WA; Wegeng, Robert S [Richland, WA; Perez, Joseph M [Richland, WA; Feng, Xiangdong [West Richland, WA; Liu, Jun [West Richland, WA

2003-03-18

The present invention is a microchannel mass exchanger having a first plurality of inner thin sheets and a second plurality of outer thin sheets. The inner thin sheets each have a solid margin around a circumference, the solid margin defining a slot through the inner thin sheet thickness. The outer thin sheets each have at least two header holes on opposite ends and when sandwiching an inner thin sheet. The outer thin sheets further have a mass exchange medium. The assembly forms a closed flow channel assembly wherein fluid enters through one of the header holes into the slot and exits through another of the header holes after contacting the mass exchange medium.

Microchannel laminated mass exchanger and method of making

DOEpatents

Martin, Peter M.; Bennett, Wendy D.; Matson, Dean W.; Stewart, Donald C.; Drost, Monte K.; Wegeng, Robert S.; Perez, Joseph M.; Feng, Xiangdong; Liu, Jun

2000-01-01

The present invention is a microchannel mass exchanger having a first plurality of inner thin sheets and a second plurality of outer thin sheets. The inner thin sheets each have a solid margin around a circumference, the solid margin defining a slot through the inner thin sheet thickness. The outer thin sheets each have at least two header holes on opposite ends and when sandwiching an inner thin sheet. The outer thin sheets further have a mass exchange medium. The assembly forms a closed flow channel assembly wherein fluid enters through one of the header holes into the slot and exits through another of the header holes after contacting the mass exchange medium.

Microchannel laminated mass exchanger and method of making

DOEpatents

Martin, Peter M [Kennewick, WA; Bennett, Wendy D [Kennewick, WA; Matson, Dean W [Kennewick, WA; Stewart, Donald C [Richland, WA; Drost, Monte K [Pasco, WA; Wegeng, Robert S [Richland, WA; Perez, Joseph M [Richland, WA; Feng, Xiangdong [West Richland, WA; Liu, Jun [West Richland, WA

2002-03-05

The present invention is a microchannel mass exchanger having a first plurality of inner thin sheets and a second plurality of outer thin sheets. The inner thin sheets each have a solid margin around a circumference, the solid margin defining a slot through the inner thin sheet thickness. The outer thin sheets each have at least two header holes on opposite ends and when sandwiching an inner thin sheet. The outer thin sheets further have a mass exchange medium. The assembly forms a closed flow channel assembly wherein fluid enters through one of the header holes into the slot and exits through another of the header holes after contacting the mass exchange medium.

47 CFR 11.61 - Tests of EAS procedures.

Code of Federal Regulations, 2010 CFR

2010-10-01

... EAS header codes, Attention Signal, Test Script and EOM code. (i) Tests in odd numbered months shall... substitute for a monthly test, activation must include transmission of the EAS header codes, Attention Signal, emergency message and EOM code and comply with the visual message requirements in § 11.51. To substitute for...

Practical End-to-End Performance Testing Tool for High Speed 3G-Based Networks

NASA Astrophysics Data System (ADS)

Shinbo, Hiroyuki; Tagami, Atsushi; Ano, Shigehiro; Hasegawa, Toru; Suzuki, Kenji

High speed IP communication is a killer application for 3rd generation (3G) mobile systems. Thus 3G network operators should perform extensive tests to check whether expected end-to-end performances are provided to customers under various environments. An important objective of such tests is to check whether network nodes fulfill requirements to durations of processing packets because a long duration of such processing causes performance degradation. This requires testers (persons who do tests) to precisely know how long a packet is hold by various network nodes. Without any tool's help, this task is time-consuming and error prone. Thus we propose a multi-point packet header analysis tool which extracts and records packet headers with synchronized timestamps at multiple observation points. Such recorded packet headers enable testers to calculate such holding durations. The notable feature of this tool is that it is implemented on off-the shelf hardware platforms, i.e., lap-top personal computers. The key challenges of the implementation are precise clock synchronization without any special hardware and a sophisticated header extraction algorithm without any drop.

Chapter 7:I-joists and headers

Treesearch

Brian K. Brashaw; Robert J. Ross

2005-01-01

Prefabricated wood I-joists and headers are widely used in wood construction throughout the world. They are used in roof and floor systems in both residential and commercial applications. These structural members consist of flanges, which are made from either solid-sawn or laminated veneer lumber, that are adhesively bonded to a web that is made of plywood or oriented...

46 CFR 52.05-45 - Circumferential joints in pipes, tubes and headers (modifies PW-41).

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Circumferential joints in pipes, tubes and headers (modifies PW-41). 52.05-45 Section 52.05-45 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS Requirements for Boilers Fabricated by Welding § 52.05-45...

Galaxy of Images

Science.gov Websites

This site has moved! Please go to our new Image Gallery site! dot header Basic Image Search Options dot header Search Tips Enter a keyword term below: Submit Use this search to find ANY words you Irish Lion Cubs Taxonomic (Scientific) Keyword Search: Submit Many of the images in the Galaxy of Images

46 CFR 52.05-45 - Circumferential joints in pipes, tubes and headers (modifies PW-41).

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 2 2014-10-01 2014-10-01 false Circumferential joints in pipes, tubes and headers (modifies PW-41). 52.05-45 Section 52.05-45 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS Requirements for Boilers Fabricated by Welding § 52.05-45...

46 CFR 52.05-45 - Circumferential joints in pipes, tubes and headers (modifies PW-41).

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 2 2011-10-01 2011-10-01 false Circumferential joints in pipes, tubes and headers (modifies PW-41). 52.05-45 Section 52.05-45 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS Requirements for Boilers Fabricated by Welding § 52.05-45...

46 CFR 52.05-45 - Circumferential joints in pipes, tubes and headers (modifies PW-41).

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 2 2012-10-01 2012-10-01 false Circumferential joints in pipes, tubes and headers (modifies PW-41). 52.05-45 Section 52.05-45 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS Requirements for Boilers Fabricated by Welding § 52.05-45...

46 CFR 52.05-45 - Circumferential joints in pipes, tubes and headers (modifies PW-41).

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 2 2013-10-01 2013-10-01 false Circumferential joints in pipes, tubes and headers (modifies PW-41). 52.05-45 Section 52.05-45 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE ENGINEERING POWER BOILERS Requirements for Boilers Fabricated by Welding § 52.05-45...

--No Title--

Science.gov Websites

.showcase,.showcasetransportation{opacity:1}.content-list-widget .header-box .title{color:#fff }.content-list-widget .header-box{background-color:#0079C2;border-bottom:5px solid #00A4E4}ul.fa-blue-arrow a::before{font-family:FontAwesome;content:'\\f138';margin:0 5px 0 -15px;color:#0079C2;text-indent

Evaluation of the thermal and structural performance of straw bale construction

NASA Astrophysics Data System (ADS)

Beaudry, Kyle R.

This thesis is primarily divided into two distinct experimental programs evaluating: 1) the thermal performance and, 2) the structural performance of straw bale construction. The thermal performance chapter describes hot-box testing (based on ASTM C1363-11) of seven straw bale wall panels to obtain their apparent thermal conductivity values. All panels were constructed with stacked bales and cement-lime plaster skins on each side of the bales. Four panels were made with traditional, 2-string field bales of densities ranging from 89.5 kg/m3 - 131 kg/m3 and with the bales on-edge (fibres perpendicular to the heat flow). Three panels were made with manufactured high-density bales (291 kg/m3 - 372 kg/m3). The fibres of the manufactured bales were randomly oriented. The key conclusion of this work is that within the experimental error, there is no difference in the apparent thermal conductivity value for panels using normal density bales and manufactured high-density bales up to a density of 333 kg/m3. The structural performance chapter describes gravity and transverse load testing (based on ASTM E72-15) of non-plastered modular straw bale wall (DBW) panels to evaluate their strength capacity and failure modes. The out-of-plane flexural (OPF) tests exhibited a mean ultimate bending moment of 49.7 kNm. The axial compression (AC) tests exhibited a mean ultimate line load of 161.0 kN/m. The local flexural header beam (HP) tests exhibited an ultimate line load of 31.6 kN/m. The OPF and AC capacities of the DBW exceeded the capacities exhibited by a conventional 38 mm x 140 mm stud wall. However, the DBW's header beam strength and stiffness was inferior to conventional stud wall.

Fallon FORGE Well Temp data

DOE Data Explorer

Doug Blankenship

2016-03-01

x,y,z downhole temperature data for wells in and around the Fallon FORGE site. Data for the following wells are included: 82-36, 82-19, 84.31, 61-36, 88-24, FOH-3D, FDU-1, and FDU-2. Data are formatted in txt format and in columns for importing into Earthvision Software. Column headers and coordinate system information is stored in the file header.

Integral collector storage system with heat exchange apparatus

DOEpatents

Rhodes, Richard O.

2004-04-20

The present invention relates to an integral solar energy collector storage systems. Generally, an integral collector storage system includes a tank system, a plurality of heat exchange tubes with at least some of the heat exchange tubes arranged within the tank system, a first glazing layer positioned over the tank system and a base plate positioned under the tank system. In one aspect of the invention, the tank system, the first glazing layer an the base plate each include protrusions and a clip is provided to hold the layers together. In another aspect of the invention, the first glazing layer and the base plate are ribbed to provide structural support. This arrangement is particularly useful when these components are formed from plastic. In yet another aspect of the invention, the tank system has a plurality of interconnected tank chambers formed from tubes. In this aspect, a supply header pipe and a fluid return header pipe are provided at a first end of the tank system. The heat exchange tubes have inlets coupled to the supply header pipe and outlets coupled to the return header pipe. With this arrangement, the heat exchange tubes may be inserted into the tank chambers from the first end of the tank system.

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2012 CFR

2012-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

40 CFR 63.7325 - What test methods and other procedures must I use to demonstrate initial compliance with the TDS...

Code of Federal Regulations, 2010 CFR

2010-07-01

...) National Emission Standards for Hazardous Air Pollutants for Coke Ovens: Pushing, Quenching, and Battery... applied to the coke (e.g., from the header that feeds water to the quench tower reservoirs). Conduct... sample of the quench water as applied to the coke (e.g., from the header that feeds water to the quench...

Writing user selectable data on the extended header of seismic recordings made on the Texas Instruments DFS-V

USGS Publications Warehouse

Robinson, W.C.

1996-01-01

A circuit has been developed to allow the writing of up to 192 digits of user-selectable data on a portion of tape called extended header, which is always available for use before each DFS-V seismic record is written. Such data could include navigation information, air gun and streamer depth and shot times.

Autonomous grain combine control system

DOEpatents

Hoskinson, Reed L.; Kenney, Kevin L.; Lucas, James R.; Prickel, Marvin A.

2013-06-25

A system for controlling a grain combine having a rotor/cylinder, a sieve, a fan, a concave, a feeder, a header, an engine, and a control system. The feeder of the grain combine is engaged and the header is lowered. A separator loss target, engine load target, and a sieve loss target are selected. Grain is harvested with the lowered header passing the grain through the engaged feeder. Separator loss, sieve loss, engine load and ground speed of the grain combine are continuously monitored during the harvesting. If the monitored separator loss exceeds the selected separator loss target, the speed of the rotor/cylinder, the concave setting, the engine load target, or a combination thereof is adjusted. If the monitored sieve loss exceeds the selected sieve loss target, the speed of the fan, the size of the sieve openings, or the engine load target is adjusted.

Ignitor with stable low-energy thermite igniting system

DOEpatents

Kelly, Michael D.; Munger, Alan C.

1991-02-05

A stable compact low-energy igniting system in an ignitor utilizes two components, an initiating charge and an output charge. The initiating charge is a thermite in ultra-fine powder form compacted to 50-70% of theoretical maximum density and disposed in a cavity of a header of the ignitor adjacent to an electrical ignition device, or bridgewire, mounted in the header cavity. The initiating charge is ignitable by operation of the ignition device in a hot-wire mode. The output charge is a thermite in high-density consoladated form compacted to 90-99% of theoretical maximum density and disposed adjacent to the initiating charge on an opposite end thereof from the electrical ignition device and ignitable by the initiating charge. A sleeve is provided for mounting the output charge to the ignitor header with the initiating charge confined therebetween in the cavity.

Secure content objects

DOEpatents

Evans, William D [Cupertino, CA

2009-02-24

A secure content object protects electronic documents from unauthorized use. The secure content object includes an encrypted electronic document, a multi-key encryption table having at least one multi-key component, an encrypted header and a user interface device. The encrypted document is encrypted using a document encryption key associated with a multi-key encryption method. The encrypted header includes an encryption marker formed by a random number followed by a derivable variation of the same random number. The user interface device enables a user to input a user authorization. The user authorization is combined with each of the multi-key components in the multi-key encryption key table and used to try to decrypt the encrypted header. If the encryption marker is successfully decrypted, the electronic document may be decrypted. Multiple electronic documents or a document and annotations may be protected by the secure content object.

System Integration Issues in Digital Photogrammetric Mapping

DTIC Science & Technology

1992-01-01

elevation models, and/or rectified imagery/ orthophotos . Imagery exported from the DSPW can be either in a tiled image format or standard raster format...data. In the near future, correlation using "window shaping" operations along with an iterative orthophoto refinements methodology (Norvelle, 1992) is...components of TIES. The IDS passes tiled image data and ASCII header data to the DSPW. The tiled image file contains only image data. The ASCII header

--No Title--

Science.gov Websites

li{list-style:none}ul#sort-by-form li{float:left;list-style:none;margin:0 3px}ul#chart-list li ul.data_set-list-item{display:block;height:88px}ul#chart-list li ul.data_set-list-item li{float:left ;display:block}ul#chart-list li.category-header{display:block}#chart-list{margin-top:10px}.header-text h3{font

The effect of travel speed on thermal response in CO2 laser welding of small electronic components

NASA Astrophysics Data System (ADS)

Gianoulakis, S. E.; Burchett, S. N.; Fuerschbach, P. W.; Knorovsky, G. A.

A comprehensive three-dimensional numerical investigation of the effect of beat source travel speed on temperatures and resulting thermal stresses was performed for CO2-laser welding. The test specimen was a small thermal battery header containing several stress-sensitive glass-to-metal seals surrounding the electrical connections and a temperature sensitive ignitor located under the header near the center. Predictions of the thermal stresses and temperatures in the battery header were made for several travel speeds of the laser. The travel speeds examined ranged from 10mm/sec to 50mm/sec. The results indicate that faster weld speeds result in lower temperatures and stresses for the same size weld. This is because the higher speed welds are more efficient, requiring less energy to produce a given weld. Less energy absorbed by the workpiece results in lower temperatures, which results in lower stresses.

Dual circuit embossed sheet heat transfer panel

DOEpatents

Morgan, G.D.

1984-02-21

A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet. 6 figs.

Dual-circuit embossed-sheet heat-transfer panel

DOEpatents

Morgan, G.D.

1982-08-23

A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed for form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.

Dual circuit embossed sheet heat transfer panel

DOEpatents

Morgan, Grover D.

1984-01-01

A heat transfer panel provides redundant cooling for fusion reactors or the like environment requiring low-mass construction. Redundant cooling is provided by two independent cooling circuits, each circuit consisting of a series of channels joined to inlet and outlet headers. The panel comprises a welded joinder of two full-size and two much smaller partial-size sheets. The first full-size sheet is embossed to form first portions of channels for the first and second circuits, as well as a header for the first circuit. The second full-sized sheet is then laid over and welded to the first full-size sheet. The first and second partial-size sheets are then overlaid on separate portions of the second full-sized sheet, and are welded thereto. The first and second partial-sized sheets are embossed to form inlet and outlet headers, which communicate with channels of the second circuit through apertures formed in the second full-sized sheet.

AASG Wells Data for the EGS Test Site Planning and Analysis Task

DOE Data Explorer

Augustine, Chad

2013-10-09

AASG Wells Data for the EGS Test Site Planning and Analysis Task Temperature measurement data obtained from boreholes for the Association of American State Geologists (AASG) geothermal data project. Typically bottomhole temperatures are recorded from log headers, and this information is provided through a borehole temperature observation service for each state. Service includes header records, well logs, temperature measurements, and other information for each borehole. Information presented in Geothermal Prospector was derived from data aggregated from the borehole temperature observations for all states. For each observation, the given well location was recorded and the best available well identified (name), temperature and depth were chosen. The “Well Name Source,” “Temp. Type” and “Depth Type” attributes indicate the field used from the original service. This data was then cleaned and converted to consistent units. The accuracy of the observation’s location, name, temperature or depth was note assessed beyond that originally provided by the service. - AASG bottom hole temperature datasets were downloaded from repository.usgin.org between the dates of May 16th and May 24th, 2013. - Datasets were cleaned to remove “null” and non-real entries, and data converted into consistent units across all datasets - Methodology for selecting ”best” temperature and depth attributes from column headers in AASG BHT Data sets: • Temperature: • CorrectedTemperature – best • MeasuredTemperature – next best • Depth: • DepthOfMeasurement – best • TrueVerticalDepth – next best • DrillerTotalDepth – last option • Well Name/Identifier • APINo – best • WellName – next best • ObservationURI - last option. The column headers are as follows: • gid = internal unique ID • src_state = the state from which the well was downloaded (note: the low temperature wells in Idaho are coded as “ID_LowTemp”, while all other wells are simply the two character state abbreviation) • source_url = the url for the source WFS service or Excel file • temp_c = “best” temperature in Celsius • temp_type = indicates whether temp_c comes from the corrected or measured temperature header column in the source document • depth_m = “best” depth in meters • depth_type = indicates whether depth_m comes from the measured, true vertical, or driller total depth header column in the source document • well_name = “best” well name or ID • name_src = indicates whether well_name came from apino, wellname, or observationuri header column in the source document • lat_wgs84 = latitude in wgs84 • lon_wgs84 = longitude in wgs84 • state = state in which the point is located • county = county in which the point is located

MINC 2.0: A Flexible Format for Multi-Modal Images.

PubMed

Vincent, Robert D; Neelin, Peter; Khalili-Mahani, Najmeh; Janke, Andrew L; Fonov, Vladimir S; Robbins, Steven M; Baghdadi, Leila; Lerch, Jason; Sled, John G; Adalat, Reza; MacDonald, David; Zijdenbos, Alex P; Collins, D Louis; Evans, Alan C

2016-01-01

It is often useful that an imaging data format can afford rich metadata, be flexible, scale to very large file sizes, support multi-modal data, and have strong inbuilt mechanisms for data provenance. Beginning in 1992, MINC was developed as a system for flexible, self-documenting representation of neuroscientific imaging data with arbitrary orientation and dimensionality. The MINC system incorporates three broad components: a file format specification, a programming library, and a growing set of tools. In the early 2000's the MINC developers created MINC 2.0, which added support for 64-bit file sizes, internal compression, and a number of other modern features. Because of its extensible design, it has been easy to incorporate details of provenance in the header metadata, including an explicit processing history, unique identifiers, and vendor-specific scanner settings. This makes MINC ideal for use in large scale imaging studies and databases. It also makes it easy to adapt to new scanning sequences and modalities.

DoD Electronic Data Interchange (EDI) Convention: ASC X12 Transaction Set 832 Price Sales Catalog (Version 003030)

DTIC Science & Technology

1992-12-01

DATA DES . ELEMENT NAME ATlNPUTES Conditional TD401 152 Special Handling Code C ID 2/3 Code specifying special transportation handling instructions. HAN...Executhre Age"t for Eketronic Conmnerce/Electmnlc Dots lnterchange/Protection of Logistica Undaasslfled/Serssltlve Systerr Executive Agent for EC/EDI...PRICEISALES CATALOG ANSI ASC X12 VERSIONIRELEASE 003030DOD_ 7 Communications Transport Protocol ISA /_Interchange Control Header GS/ Functional Group Header

Long-Life Thermal Battery for Sonobuoy

DTIC Science & Technology

2000-04-20

Microtherm insulation. This Phase I project provided a cost-effective prototype development for fully meeting size ’A’ sonobuoy performance objectives. An...Crossection of Thermal Battery inside V/M-Insulated Battery Case having a Spun Inner Wall and the Standard Battery Can ( Microtherm added at header-end...34 thick Microtherm — — / 0.250" extra Fiberfrax Wrap X^ 0.075 " vacuum annulus ,/ Detail of Header-End 0.250’’ Fig.l, Drawing of a Prototype

Hyperswitch Network For Hypercube Computer

NASA Technical Reports Server (NTRS)

Chow, Edward; Madan, Herbert; Peterson, John

1989-01-01

Data-driven dynamic switching enables high speed data transfer. Proposed hyperswitch network based on mixed static and dynamic topologies. Routing header modified in response to congestion or faults encountered as path established. Static topology meets requirement if nodes have switching elements that perform necessary routing header revisions dynamically. Hypercube topology now being implemented with switching element in each computer node aimed at designing very-richly-interconnected multicomputer system. Interconnection network connects great number of small computer nodes, using fixed hypercube topology, characterized by point-to-point links between nodes.

A 2.2 sq m /24 sq ft/ self-controlled deployable heat pipe radiator - Design and test

NASA Technical Reports Server (NTRS)

Edelstein, F.

1975-01-01

An all heat pipe, deployable radiator has been developed which can effectively control pumped fluid loop temperatures under varying loads using variable conductance panel heat pipes. The 2.2 sq m (24 sq ft) aluminum panel can be coupled to either a fluid header or a flexible heat pipe header capable of transporting 850 watts in a 90-deg bent configuration. Test results support the feasibility of using this system to passively control Freon-21 loop temperatures.

A Document-Based EHR System That Controls the Disclosure of Clinical Documents Using an Access Control List File Based on the HL7 CDA Header.

PubMed

Takeda, Toshihiro; Ueda, Kanayo; Nakagawa, Akito; Manabe, Shirou; Okada, Katsuki; Mihara, Naoki; Matsumura, Yasushi

2017-01-01

Electronic health record (EHR) systems are necessary for the sharing of medical information between care delivery organizations (CDOs). We developed a document-based EHR system in which all of the PDF documents that are stored in our electronic medical record system can be disclosed to selected target CDOs. An access control list (ACL) file was designed based on the HL7 CDA header to manage the information that is disclosed.

Degassifying and mixing apparatus for liquids. [potable water for spacecraft

NASA Technical Reports Server (NTRS)

Yamauchi, S. T. (Inventor)

1983-01-01

An apparatus for degassing a liquid comprises a containment vessel a liquid pump and a header assembly (12) within the containment vessel in a volume above the reservoir of the liquid. The pump draws from this reservoir and outputs to the header assembly, the latter being constructed to return the liquid to the reservoir in the form of a number of stacked, vertically spaced, concentric, conical cascades via orifices. A vacuum source provides a partial vacuum in the containment vessel to enhance the degassing process.

CMOS: Efficient Clustered Data Monitoring in Sensor Networks

PubMed Central

2013-01-01

Tiny and smart sensors enable applications that access a network of hundreds or thousands of sensors. Thus, recently, many researchers have paid attention to wireless sensor networks (WSNs). The limitation of energy is critical since most sensors are battery-powered and it is very difficult to replace batteries in cases that sensor networks are utilized outdoors. Data transmission between sensor nodes needs more energy than computation in a sensor node. In order to reduce the energy consumption of sensors, we present an approximate data gathering technique, called CMOS, based on the Kalman filter. The goal of CMOS is to efficiently obtain the sensor readings within a certain error bound. In our approach, spatially close sensors are grouped as a cluster. Since a cluster header generates approximate readings of member nodes, a user query can be answered efficiently using the cluster headers. In addition, we suggest an energy efficient clustering method to distribute the energy consumption of cluster headers. Our simulation results with synthetic data demonstrate the efficiency and accuracy of our proposed technique. PMID:24459444

CMOS: efficient clustered data monitoring in sensor networks.

PubMed

Min, Jun-Ki

2013-01-01

Tiny and smart sensors enable applications that access a network of hundreds or thousands of sensors. Thus, recently, many researchers have paid attention to wireless sensor networks (WSNs). The limitation of energy is critical since most sensors are battery-powered and it is very difficult to replace batteries in cases that sensor networks are utilized outdoors. Data transmission between sensor nodes needs more energy than computation in a sensor node. In order to reduce the energy consumption of sensors, we present an approximate data gathering technique, called CMOS, based on the Kalman filter. The goal of CMOS is to efficiently obtain the sensor readings within a certain error bound. In our approach, spatially close sensors are grouped as a cluster. Since a cluster header generates approximate readings of member nodes, a user query can be answered efficiently using the cluster headers. In addition, we suggest an energy efficient clustering method to distribute the energy consumption of cluster headers. Our simulation results with synthetic data demonstrate the efficiency and accuracy of our proposed technique.

Pacemaker syndrome with sub-acute left ventricular systolic dysfunction in a patient with a dual-chamber pacemaker: consequence of lead switch at the header.

PubMed

Khurwolah, Mohammad Reeaze; Vezi, Brian Zwelethini

In the daily practice of pacemaker insertion, the occurrence of atrial and ventricular lead switch at the pacemaker box header is a rare and unintentional phenomenon, with less than five cases reported in the literature. The lead switch may have dire consequences, depending on the indication for the pacemaker. One of these consequences is pacemaker syndrome, in which the normal sequence of atrial and ventricular activation is impaired, leading to sub-optimal ventricular filling and cardiac output. It is important for the attending physician to recognise any worsening of symptoms in a patient who has recently had a permanent pacemaker inserted. In the case of a dual-chamber pacemaker, switching of the atrial and ventricular leads at the pacemaker box header should be strongly suspected. We present an unusual case of pacemaker syndrome and right ventricular-only pacinginduced left ventricular systolic dysfunction in a patient with a dual-chamber pacemaker.

An automatic detection method for the boiler pipe header based on real-time image acquisition

NASA Astrophysics Data System (ADS)

Long, Yi; Liu, YunLong; Qin, Yongliang; Yang, XiangWei; Li, DengKe; Shen, DingJie

2017-06-01

Generally, an endoscope is used to test the inner part of the thermal power plants boiler pipe header. However, since the endoscope hose manual operation, the length and angle of the inserted probe cannot be controlled. Additionally, it has a big blind spot observation subject to the length of the endoscope wire. To solve these problems, an automatic detection method for the boiler pipe header based on real-time image acquisition and simulation comparison techniques was proposed. The magnetic crawler with permanent magnet wheel could carry the real-time image acquisition device to complete the crawling work and collect the real-time scene image. According to the obtained location by using the positioning auxiliary device, the position of the real-time detection image in a virtual 3-D model was calibrated. Through comparing of the real-time detection images and the computer simulation images, the defects or foreign matter fall into could be accurately positioning, so as to repair and clean up conveniently.

Ampule tests to simulate glass corrosion in ambient temperature lithium batteries. Volume 2

DOE Office of Scientific and Technical Information (OSTI.GOV)

Douglas, S.C.; Bunker, B.C.; Crafts, C.C.

1984-06-01

Glass corrosion in battery headers has been found to limit the shelf life of ambient temperature lithium batteries. Glass corrosion can lead to loss of battery electrolytes or to shorts across the conductive corrosion product. Tests have been conducted which simulate the corrosive environment in a battery by sealing headers attached to lithium metal into Pyrex ampules containing battery electrolyte. Using the ampule test, glass corrosion kinetics have been determined at 70/sup 0/C for the Li/SO/sub 2/, Li/SOCl/sub 2/, and Li/SOCl/sub 2/ + BrCl battery systems. Test results indicate that corrosion of commercial glass compositions is extensive in all electrolytesmore » tested, resulting in predicted battery failures after several months. Sandia's TA-23 glass corrodes at a much slower rate, indicating a projected battery lifetime of over five years in the Li/SO/sub 2/ system. Test results reveal that corrosion kinetics are sensitive to header polarization, stress, and configuration as well as glass composition.« less

Semiconductor bridge (SCB) detonator

DOEpatents

Bickes, Jr., Robert W.; Grubelich, Mark C.

1999-01-01

The present invention is a low-energy detonator for high-density secondary-explosive materials initiated by a semiconductor bridge igniter that comprises a pair of electrically conductive lands connected by a semiconductor bridge. The semiconductor bridge is in operational or direct contact with the explosive material, whereby current flowing through the semiconductor bridge causes initiation of the explosive material. Header wires connected to the electrically-conductive lands and electrical feed-throughs of the header posts of explosive devices, are substantially coaxial to the direction of current flow through the SCB, i.e., substantially coaxial to the SCB length.

Gasdynamic modeling and parametric study of mesoscale internal combustion swing engine/generator systems

NASA Astrophysics Data System (ADS)

Gu, Yongxian

The demand of portable power generation systems for both domestic and military applications has driven the advances of mesoscale internal combustion engine systems. This dissertation was devoted to the gasdynamic modeling and parametric study of the mesoscale internal combustion swing engine/generator systems. First, the system-level thermodynamic modeling for the swing engine/generator systems has been developed. The system performance as well as the potentials of both two- and four-stroke swing engine systems has been investigated based on this model. Then through parameterc studies, the parameters that have significant impacts on the system performance have been identified, among which, the burn time and spark advance time are the critical factors related to combustion process. It is found that the shorter burn time leads to higher system efficiency and power output and the optimal spark advance time is about half of the burn time. Secondly, the turbulent combustion modeling based on levelset method (G-equation) has been implemented into the commercial software FLUENT. Thereafter, the turbulent flame propagation in a generic mesoscale combustion chamber and realistic swing engine chambers has been studied. It is found that, in mesoscale combustion engines, the burn time is dominated by the mean turbulent kinetic energy in the chamber. It is also shown that in a generic mesoscale combustion chamber, the burn time depends on the longest distance between the initial ignition kernel to its walls and by changing the ignition and injection locations, the burn time can be reduced by a factor of two. Furthermore, the studies of turbulent flame propagation in real swing engine chambers show that the combustion can be enhanced through in-chamber turbulence augmentation and with higher engine frequency, the burn time is shorter, which indicates that the in-chamber turbulence can be induced by the motion of moving components as well as the intake gas jet flow. The burn time for current two-stroke swing engine is estimated as about 2.5 ms, which can be used in the prescribed burned mass fraction profile that follows the Wiebe's function. Finally, a 2D CFD code for compressible flow has been developed to study wave interactions in the engine and header system. It is found that with realistic working conditions, for a two-stroke swing engine, certain expansion waves can be created by the exhaust gas flows and the chamber pressure can reach as low as 5 psi below one atmosphere, which helps fill fresh reactant charge. The results also show that to obtain appropriate header tuning for the current two-stroke swing engine, the length of the header neck is about 40 cm.

CLIPS++: Embedding CLIPS into C++

NASA Technical Reports Server (NTRS)

Obermeyer, Lance; Miranker, Daniel P.

1994-01-01

This paper describes a set of C++ extensions to the CLIPS language and their embodiment in CLIPS++. These extensions and the implementation approach of CLIPS++ provide a new level of embeddability with C and C++. These extensions are a C++ include statement and a defcontainer construct; (include (c++-header-file.h)) and (defcontainer (c++-type)). The include construct allows C++ functions to be embedded in both the LHS and RHS of CLIPS rules. The header file in an include construct is the same header file the programmer uses for his/her own C++ code, independent of CLIPS. The defcontainer construct allows the inference engine to treat C++ class instances as CLIPS deftemplate facts. Consequently existing C++ class libraries may be transparently imported into CLIPS. These C++ types may use advanced features like inheritance, virtual functions, and templates. The implementation has been tested with several class libraries, including Rogue Wave Software's Tools.h++, GNU's libg++, and USL's C++ Standard Components. The execution speed of CLIPS++ has been determined to be 5 to 700 times the execution speed of CLIPS 6.0 (10 to 20X typical).

Apparatus and methods for supplying auxiliary steam in a combined cycle system

DOEpatents

Gorman, William G.; Carberg, William George; Jones, Charles Michael

2002-01-01

To provide auxiliary steam, a low pressure valve is opened in a combined cycle system to divert low pressure steam from the heat recovery steam generator to a header for supplying steam to a second combined cycle's steam turbine seals, sparging devices and cooling steam for the steam turbine if the steam turbine and gas turbine lie on a common shaft with the generator. Cooling steam is supplied the gas turbine in the combined cycle system from the high pressure steam turbine. Spent gas turbine cooling steam may augment the low pressure steam supplied to the header by opening a high pressure valve whereby high and low pressure steam flows are combined. An attemperator is used to reduce the temperature of the combined steam in response to auxiliary steam flows above a predetermined flow and a steam header temperature above a predetermined temperature. The auxiliary steam may be used to start additional combined cycle units or to provide a host unit with steam turbine cooling and sealing steam during full-speed no-load operation after a load rejection.

West Flank Coso, CA FORGE 3D geologic model

DOE Data Explorer

Doug Blankenship

2016-03-01

This is an x,y,z file of the West Flank FORGE 3D geologic model. Model created in Earthvision by Dynamic Graphic Inc. The model was constructed with a grid spacing of 100 m. Geologic surfaces were extrapolated from the input data using a minimum tension gridding algorithm. The data file is tabular data in a text file, with lithology data associated with X,Y,Z grid points. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

Fallon FORGE 3D Geologic Model

DOE Data Explorer

Doug Blankenship

2016-03-01

An x,y,z scattered data file for the 3D geologic model of the Fallon FORGE site. Model created in Earthvision by Dynamic Graphic Inc. The model was constructed with a grid spacing of 100 m. Geologic surfaces were extrapolated from the input data using a minimum tension gridding algorithm. The data file is tabular data in a text file, with lithology data associated with X,Y,Z grid points. All the relevant information is in the file header (the spatial reference, the projection etc.) In addition all the fields in the data file are identified in the header.

Semiconductor bridge (SCB) detonator

DOEpatents

Bickes, R.W. Jr.; Grubelich, M.C.

1999-01-19

The present invention is a low-energy detonator for high-density secondary-explosive materials initiated by a semiconductor bridge (SCB) igniter that comprises a pair of electrically conductive lands connected by a semiconductor bridge. The semiconductor bridge is in operational or direct contact with the explosive material, whereby current flowing through the semiconductor bridge causes initiation of the explosive material. Header wires connected to the electrically-conductive lands and electrical feed-throughs of the header posts of explosive devices, are substantially coaxial to the direction of current flow through the SCB, i.e., substantially coaxial to the SCB length. 3 figs.

Sleep patterns and match performance in elite Australian basketball athletes.

PubMed

Staunton, Craig; Gordon, Brett; Custovic, Edhem; Stanger, Jonathan; Kingsley, Michael

2017-08-01

To assess sleep patterns and associations between sleep and match performance in elite Australian female basketball players. Prospective cohort study. Seventeen elite female basketball players were monitored across two consecutive in-season competitions (30 weeks). Total sleep time and sleep efficiency were determined using triaxial accelerometers for Baseline, Pre-match, Match-day and Post-match timings. Match performance was determined using the basketball efficiency statistic (EFF). The effects of match schedule (Regular versus Double-Header; Home versus Away) and sleep on EFF were assessed. The Double-Header condition changed the pattern of sleep when compared with the Regular condition (F (3,48) =3.763, P=0.017), where total sleep time Post-match was 11% less for Double-Header (mean±SD; 7.2±1.4h) compared with Regular (8.0±1.3h; P=0.007). Total sleep time for Double-Header was greater Pre-match (8.2±1.7h) compared with Baseline (7.1±1.6h; P=0.022) and Match-day (7.3±1.5h; P=0.007). Small correlations existed between sleep metrics at Pre-match and EFF for pooled data (r=-0.39 to -0.22; P≥0.238). Relationships between total sleep time and EFF ranged from moderate negative to large positive correlations for individual players (r=-0.37 to 0.62) and reached significance for one player (r=0.60; P=0.025). Match schedule can affect the sleep patterns of elite female basketball players. A large degree of inter-individual variability existed in the relationship between sleep and match performance; nevertheless, sleep monitoring might assist in the optimisation of performance for some athletes. Copyright © 2017 Sports Medicine Australia. Published by Elsevier Ltd. All rights reserved.

Types and analysis of defects in welding junctions of the header to steam generator shells on power-generating units with VVER-1000

NASA Astrophysics Data System (ADS)

Ozhigov, L. S.; Voevodin, V. N.; Mitrofanov, A. S.; Vasilenko, R. L.

2016-10-01

Investigation objects were metal templates, which were cut during the repair of welding junction no. 111 (header to the steam generator shell) on a power-generating unit with VVER-1000 of the South-Ukraine NPP, and substances of mud depositions collected from walls of this junction. Investigations were carried out using metallography, optical microscopy, and scanning electron microscopy with energy dispersion microanalysis by an MMO-1600-AT metallurgical microscope and a JEOL JSM-7001F scanning electron microscope with the Shottky cathode. As a result of investigations in corrosion pits and mud depositions in the area of welding junction no. 111, iron and copper-enriched particles were revealed. It is shown that, when contacting with the steel header surface, these particles can form microgalvanic cells causing reactions of iron dissolution and the pit corrosion of metal. Nearby corrosion pits in metal are microcracks, which can be effect of the stress state of metal under corrosion pits along with revealed effects of twinning. The hypothesis is expressed that pitting corrosion of metal occurred during the first operation period of the power-generating unit in the ammonia water chemistry conditions (WCC). The formation of corrosion pits and nucleating cracks from them was stopped with the further operation under morpholine WCC. The absence of macrocracks in metal of templates verifies that, during operation, welding junction no. 111 operated under load conditions not exceeding the permissible ones by design requirements. The durability of the welding junction of the header to the steam generator shell significantly depends on the technological schedule of chemical cleaning and steam generator shut-down cooling.

Direct cooled power electronics substrate

DOEpatents

Wiles, Randy H [Powell, TN; Wereszczak, Andrew A [Oak Ridge, TN; Ayers, Curtis W [Kingston, TN; Lowe, Kirk T [Knoxville, TN

2010-09-14

The disclosure describes directly cooling a three-dimensional, direct metallization (DM) layer in a power electronics device. To enable sufficient cooling, coolant flow channels are formed within the ceramic substrate. The direct metallization layer (typically copper) may be bonded to the ceramic substrate, and semiconductor chips (such as IGBT and diodes) may be soldered or sintered onto the direct metallization layer to form a power electronics module. Multiple modules may be attached to cooling headers that provide in-flow and out-flow of coolant through the channels in the ceramic substrate. The modules and cooling header assembly are preferably sized to fit inside the core of a toroidal shaped capacitor.

DTS Raw Data Guelph, ON Canada

DOE Data Explorer

Thomas Coleman

2013-07-31

Unprocessed active distributed temperature sensing (DTS) data from 3 boreholes in the Guelph, ON Canada region. Data from borehole 1 was collected during a fluid injection while data from boreholes 2 and 3 were collected under natural gradient conditions in a lined borehole. The column labels/headers (in the first row) define the time since start of measurement in seconds and the row labels/headers (in the first column) are the object IDs that are defined in the metadata. Each object ID is a sampling location whose exact location is defined in the metadata file. Data in each cell are temperature in Celsius at time and sampling location as defined above.

FUEL SUBASSEMBLY CONSTRUCTION FOR RADIAL FLOW IN A NUCLEAR REACTOR

DOEpatents

Treshow, M.

1962-12-25

An assembly of fuel elements for a boiling water reactor arranged for radial flow of the coolant is described. The ingress for the coolant is through a central header tube, perforated with parallel circumferertial rows of openings each having a lip to direct the coolant flow downward. Around the central tube there are a number of equally spaced concentric trays, closely fitiing the central header tube. Cylindrical fuel elements are placed in a regular pattern around the central tube, piercing the trays. A larger tube encloses the arrangement, with space provided for upward flow of coolart beyond the edge of the trays. (AEC)

Stack configurations for tubular solid oxide fuel cells

DOEpatents

Armstrong, Timothy R.; Trammell, Michael P.; Marasco, Joseph A.

2010-08-31

A fuel cell unit includes an array of solid oxide fuel cell tubes having porous metallic exterior surfaces, interior fuel cell layers, and interior surfaces, each of the tubes having at least one open end; and, at least one header in operable communication with the array of solid oxide fuel cell tubes for directing a first reactive gas into contact with the porous metallic exterior surfaces and for directing a second reactive gas into contact with the interior surfaces, the header further including at least one busbar disposed in electrical contact with at least one surface selected from the group consisting of the porous metallic exterior surfaces and the interior surfaces.

The Communication Link and Error ANalysis (CLEAN) simulator

NASA Technical Reports Server (NTRS)

Ebel, William J.; Ingels, Frank M.; Crowe, Shane

1993-01-01

During the period July 1, 1993 through December 30, 1993, significant developments to the Communication Link and Error ANalysis (CLEAN) simulator were completed and include: (1) Soft decision Viterbi decoding; (2) node synchronization for the Soft decision Viterbi decoder; (3) insertion/deletion error programs; (4) convolutional encoder; (5) programs to investigate new convolutional codes; (6) pseudo-noise sequence generator; (7) soft decision data generator; (8) RICE compression/decompression (integration of RICE code generated by Pen-Shu Yeh at Goddard Space Flight Center); (9) Markov Chain channel modeling; (10) percent complete indicator when a program is executed; (11) header documentation; and (12) help utility. The CLEAN simulation tool is now capable of simulating a very wide variety of satellite communication links including the TDRSS downlink with RFI. The RICE compression/decompression schemes allow studies to be performed on error effects on RICE decompressed data. The Markov Chain modeling programs allow channels with memory to be simulated. Memory results from filtering, forward error correction encoding/decoding, differential encoding/decoding, channel RFI, nonlinear transponders and from many other satellite system processes. Besides the development of the simulation, a study was performed to determine whether the PCI provides a performance improvement for the TDRSS downlink. There exist RFI with several duty cycles for the TDRSS downlink. We conclude that the PCI does not improve performance for any of these interferers except possibly one which occurs for the TDRS East. Therefore, the usefulness of the PCI is a function of the time spent transmitting data to the WSGT through the TDRS East transponder.

Average glandular dose in paired digital mammography and digital breast tomosynthesis acquisitions in a population based screening program: effects of measuring breast density, air kerma and beam quality

NASA Astrophysics Data System (ADS)

Helge Østerås, Bjørn; Skaane, Per; Gullien, Randi; Catrine Trægde Martinsen, Anne

2018-02-01

The main purpose was to compare average glandular dose (AGD) for same-compression digital mammography (DM) and digital breast tomosynthesis (DBT) acquisitions in a population based screening program, with and without breast density stratification, as determined by automatically calculated breast density (Quantra™). Secondary, to compare AGD estimates based on measured breast density, air kerma and half value layer (HVL) to DICOM metadata based estimates. AGD was estimated for 3819 women participating in the screening trial. All received craniocaudal and mediolateral oblique views of each breasts with paired DM and DBT acquisitions. Exposure parameters were extracted from DICOM metadata. Air kerma and HVL were measured for all beam qualities used to acquire the mammograms. Volumetric breast density was estimated using Quantra™. AGD was estimated using the Dance model. AGD reported directly from the DICOM metadata was also assessed. Mean AGD was 1.74 and 2.10 mGy for DM and DBT, respectively. Mean DBT/DM AGD ratio was 1.24. For fatty breasts: mean AGD was 1.74 and 2.27 mGy for DM and DBT, respectively. For dense breasts: mean AGD was 1.73 and 1.79 mGy, for DM and DBT, respectively. For breasts of similar thickness, dense breasts had higher AGD for DM and similar AGD for DBT. The DBT/DM dose ratio was substantially lower for dense compared to fatty breasts (1.08 versus 1.33). The average c-factor was 1.16. Using previously published polynomials to estimate glandularity from thickness underestimated the c-factor by 5.9% on average. Mean AGD error between estimates based on measurements (air kerma and HVL) versus DICOM header data was 3.8%, but for one mammography unit as high as 7.9%. Mean error of using the AGD value reported in the DICOM header was 10.7 and 13.3%, respectively. Thus, measurement of breast density, radiation dose and beam quality can substantially affect AGD estimates.

Average glandular dose in paired digital mammography and digital breast tomosynthesis acquisitions in a population based screening program: effects of measuring breast density, air kerma and beam quality.

PubMed

Østerås, Bjørn Helge; Skaane, Per; Gullien, Randi; Martinsen, Anne Catrine Trægde

2018-01-25

The main purpose was to compare average glandular dose (AGD) for same-compression digital mammography (DM) and digital breast tomosynthesis (DBT) acquisitions in a population based screening program, with and without breast density stratification, as determined by automatically calculated breast density (Quantra ™ ). Secondary, to compare AGD estimates based on measured breast density, air kerma and half value layer (HVL) to DICOM metadata based estimates. AGD was estimated for 3819 women participating in the screening trial. All received craniocaudal and mediolateral oblique views of each breasts with paired DM and DBT acquisitions. Exposure parameters were extracted from DICOM metadata. Air kerma and HVL were measured for all beam qualities used to acquire the mammograms. Volumetric breast density was estimated using Quantra ™ . AGD was estimated using the Dance model. AGD reported directly from the DICOM metadata was also assessed. Mean AGD was 1.74 and 2.10 mGy for DM and DBT, respectively. Mean DBT/DM AGD ratio was 1.24. For fatty breasts: mean AGD was 1.74 and 2.27 mGy for DM and DBT, respectively. For dense breasts: mean AGD was 1.73 and 1.79 mGy, for DM and DBT, respectively. For breasts of similar thickness, dense breasts had higher AGD for DM and similar AGD for DBT. The DBT/DM dose ratio was substantially lower for dense compared to fatty breasts (1.08 versus 1.33). The average c-factor was 1.16. Using previously published polynomials to estimate glandularity from thickness underestimated the c-factor by 5.9% on average. Mean AGD error between estimates based on measurements (air kerma and HVL) versus DICOM header data was 3.8%, but for one mammography unit as high as 7.9%. Mean error of using the AGD value reported in the DICOM header was 10.7 and 13.3%, respectively. Thus, measurement of breast density, radiation dose and beam quality can substantially affect AGD estimates.

Modular heat exchanger

DOEpatents

Culver, Donald W.

1978-01-01

A heat exchanger for use in nuclear reactors includes a heat exchange tube bundle formed from similar modules each having a hexagonal shroud containing a large number of thermally conductive tubes which are connected with inlet and outlet headers at opposite ends of each module, the respective headers being adapted for interconnection with suitable inlet and outlet manifold means. In order to adapt the heat exchanger for operation in a high temperature and high pressure environment and to provide access to all tube ports at opposite ends of the tube bundle, a spherical tube sheet is arranged in sealed relation across the chamber with an elongated duct extending outwardly therefrom to provide manifold means for interconnection with the opposite end of the tube bundle.

A novel fuzzy logic-based image steganography method to ensure medical data security.

PubMed

Karakış, R; Güler, I; Çapraz, I; Bilir, E

2015-12-01

This study aims to secure medical data by combining them into one file format using steganographic methods. The electroencephalogram (EEG) is selected as hidden data, and magnetic resonance (MR) images are also used as the cover image. In addition to the EEG, the message is composed of the doctor׳s comments and patient information in the file header of images. Two new image steganography methods that are based on fuzzy-logic and similarity are proposed to select the non-sequential least significant bits (LSB) of image pixels. The similarity values of the gray levels in the pixels are used to hide the message. The message is secured to prevent attacks by using lossless compression and symmetric encryption algorithms. The performance of stego image quality is measured by mean square of error (MSE), peak signal-to-noise ratio (PSNR), structural similarity measure (SSIM), universal quality index (UQI), and correlation coefficient (R). According to the obtained result, the proposed method ensures the confidentiality of the patient information, and increases data repository and transmission capacity of both MR images and EEG signals. Copyright © 2015 Elsevier Ltd. All rights reserved.

Elements of a next generation time-series ASCII data file format for Earth Sciences

NASA Astrophysics Data System (ADS)

Webster, C. J.

2015-12-01

Data in ASCII comma separated value (CSV) format are recognized as the most simple, straightforward and readable type of data present in the geosciences. Many scientific workflows developed over the years rely on data using this simple format. However, there is a need for a lightweight ASCII header format standard that is easy to create and easy to work with. Current OGC grade XML standards are complex and difficult to implement for researchers with few resources. Ideally, such a format should provide the data in CSV for easy consumption by generic applications such as spreadsheets. The format should use an existing time standard. The header should be easily human readable as well as machine parsable. The metadata format should be extendable to allow vocabularies to be adopted as they are created by external standards bodies. The creation of such a format will increase the productivity of software engineers and scientists because fewer translators and checkers would be required. Data in ASCII comma separated value (CSV) format are recognized as the most simple, straightforward and readable type of data present in the geosciences. Many scientific workflows developed over the years rely on data using this simple format. However, there is a need for a lightweight ASCII header format standard that is easy to create and easy to work with. Current OGC grade XML standards are complex and difficult to implement for researchers with few resources. Ideally, such a format would provide the data in CSV for easy consumption by generic applications such as spreadsheets. The format would use existing time standard. The header would be easily human readable as well as machine parsable. The metadata format would be extendable to allow vocabularies to be adopted as they are created by external standards bodies. The creation of such a format would increase the productivity of software engineers and scientists because fewer translators would be required.

HEAVY WATER MODERATED NEUTRONIC REACTOR

DOEpatents

Szilard, L.

1958-04-29

A nuclear reactor of the type which utilizes uranium fuel elements and a liquid coolant is described. The fuel elements are in the form of elongated tubes and are disposed within outer tubes extending through a tank containing heavy water, which acts as a moderator. The ends of the fuel tubes are connected by inlet and discharge headers, and liquid bismuth is circulated between the headers and through the fuel tubes for cooling. Helium is circulated through the annular space between the outer tubes in the tank and the fuel tubes to cool the water moderator to prevent boiling. The fuel tubes are covered with a steel lining, and suitable control means, heat exchange means, and pumping means for the coolants are provided to complete the reactor assembly.

Initial Experience With A Prototype Storage System At The University Of North Carolina

NASA Astrophysics Data System (ADS)

Creasy, J. L.; Loendorf, D. D.; Hemminger, B. M.

1986-06-01

A prototype archiving system manufactured by the 3M Corporation has been in place at the University of North Carolina for approximately 12 months. The system was installed as a result of a collaboration between 3M and UNC, with 3M seeking testing of their system, and UNC realizing the need for an archiving system as an essential part of their PACS test-bed facilities. System hardware includes appropriate network and disk interface devices as well as media for both short and long term storage of images and their associated information. The system software includes those procedures necessary to communicate with the network interface elements(NIEs) as well as those procedures necessary to interpret the ACR-NEMA header blocks and to store the images. A subset of the total ACR-NEMA header is parsed and stored in a relational database system. The entire header is stored on disk with the completed study. Interactive programs have been developed that allow radiologists to easily retrieve information about the archived images and to send the full images to a viewing console. Initial experience with the system has consisted primarily of hardware and software debugging. Although the system is ACR-NEMA compatable, further objective and subjective assessments of system performance is awaiting the connection of compatable consoles and acquisition devices to the network.

Turbine vane structure

DOEpatents

Irwin, John A.

1980-08-19

A liquid cooled stator blade assembly for a gas turbine engine includes an outer shroud having a pair of liquid inlets and a pair of liquid outlets supplied through a header and wherein means including tubes support the header radially outwardly of the shroud and also couple the header with the pair of liquid inlets and outlets. A pair of turbine vanes extend radially between the shroud and a vane platform to define a gas turbine motive fluid passage therebetween; and each of the vanes is cooled by an internal body casting of super alloy material with a grooved layer of highly heat conductive material that includes spaced apart flat surface trailing edges in alignment with a flat trailing edge of the casting joined to wall segments of the liner which are juxtaposed with respect to the internal casting to form an array of parallel liquid inlet passages on one side of the vane and a second plurality of parallel liquid return passages on the opposite side of the vane; and a superalloy heat and wear resistant imperforate skin covers the outer surface of the composite blade including the internal casting and the heat conductive layer; a separate trailing edge section includes an internal casting and an outer skin butt connected to the end surfaces of the internal casting and the heat conductive layer to form an easily assembled liquid cooled trailing edge section in the turbine vane.

Data rescue of NASA First ISLSCP (International Satellite Land Surface Climatology Project) Field Experiment (FIFE) aerial observations

NASA Astrophysics Data System (ADS)

Santhana Vannan, S. K.; Boyer, A.; Deb, D.; Beaty, T.; Wei, Y.; Wei, Z.

2017-12-01

The Oak Ridge National Laboratory Distributed Active Archive Center (ORNL DAAC) for biogeochemical dynamics is one of the NASA Earth Observing System Data and Information System (EOSDIS) data centers. ORNL DAAC (https://daac.ornl.gov) is responsible for data archival, product development and distribution, and user support for biogeochemical and ecological data and models. In particular, ORNL DAAC has been providing data management support for NASA's terrestrial ecology field campaign programs for the last several decades. Field campaigns combine ground, aircraft, and satellite-based measurements in specific ecosystems over multi-year time periods. The data collected during NASA field campaigns are archived at the ORNL DAAC (https://daac.ornl.gov/get_data/). This paper describes the effort of the ORNL DAAC team for data rescue of a First ISLSCP Field Experiment (FIFE) dataset containing airborne and satellite data observations from the 1980s. The data collected during the FIFE campaign contain high resolution aerial imageries collected over Kansas. The data rescue workflow was prepared to test for successful recovery of the data from a CD-ROM and to ensure that the data are usable and preserved for the future. The imageries contain spectral reflectance data that can be used as a historical benchmark to examine climatological and ecological changes in the Kansas region since the 1980s. Below are the key steps taken to convert the files to modern standards. Decompress the imageries using custom compression software provided with the data. The compression algorithm created for MS-DOS in 1980s had to be set up to run on modern computer systems. Decompressed files were geo-referenced by using metadata information stored in separate compressed header files. Standardized file names were applied (File names and details were described in separate readme documents). Image files were converted to GeoTIFF format with embedded georeferencing information. Leverage Open Geospatial Consortium (OGC) Web services to provide dynamic data transformation and visualization. We will describe the steps in detail and share lessons learned during the AGU session.

Visualization of JPEG Metadata

NASA Astrophysics Data System (ADS)

Malik Mohamad, Kamaruddin; Deris, Mustafa Mat

There are a lot of information embedded in JPEG image than just graphics. Visualization of its metadata would benefit digital forensic investigator to view embedded data including corrupted image where no graphics can be displayed in order to assist in evidence collection for cases such as child pornography or steganography. There are already available tools such as metadata readers, editors and extraction tools but mostly focusing on visualizing attribute information of JPEG Exif. However, none have been done to visualize metadata by consolidating markers summary, header structure, Huffman table and quantization table in a single program. In this paper, metadata visualization is done by developing a program that able to summarize all existing markers, header structure, Huffman table and quantization table in JPEG. The result shows that visualization of metadata helps viewing the hidden information within JPEG more easily.

Sample EPA Biotech Form

EPA Pesticide Factsheets

This sample “EPA Biotech Form” is a header sheet that will accompany all biotechnology submission choices, including MCANs, TERAs, Tier I and Tier II exemption, and biotechnology Test Market Exemption Applications (TMEAs).

Teleradiology mobile internet system with a new information security solution

NASA Astrophysics Data System (ADS)

Satoh, Hitoshi; Niki, Noboru; Eguchi, Kenji; Ohmatsu, Hironobu; Kusumoto, Masahiko; Kaneko, Masahiro; Moriyama, Noriyuki

2014-03-01

We have developed an external storage system by using secret sharing scheme and tokenization for regional medical cooperation, PHR service and information preservation. The use of mobile devices such as smart phones and tablets will be accelerated for a PHR service, and the confidential medical information is exposed to the risk of damage and intercept. We verified the transfer rate of the sending and receiving of data to and from the external storage system that connected it with PACS by the Internet this time. External storage systems are the data centers that exist in Okinawa, in Osaka, in Sapporo and in Tokyo by using secret sharing scheme. PACS continuously transmitted 382 CT images to the external data centers. Total capacity of the CT images is about 200MB. The total time that had been required to transmit was about 250 seconds. Because the preservation method to use secret sharing scheme is applied, security is strong. But, it also takes the information transfer time of this system too much. Therefore, DICOM data is masked to the header information part because it is made to anonymity in our method. The DICOM data made anonymous is preserved in the data base in the hospital. Header information including individual information is divided into two or more tallies by secret sharing scheme, and preserved at two or more external data centers. The token to relate the DICOM data anonymity made to header information preserved outside is strictly preserved in the token server. The capacity of header information that contains patient's individual information is only about 2% of the entire DICOM data. This total time that had been required to transmit was about 5 seconds. Other, common solutions that can protect computer communication networks from attacks are classified as cryptographic techniques or authentication techniques. Individual number IC card is connected with electronic certification authority of web medical image conference system. Individual number IC card is given only to the person to whom the authority to operate web medical image conference system was given.

47 CFR 11.33 - EAS Decoder.

Code of Federal Regulations, 2011 CFR

2011-10-01

... time periods expire. (4) Display and logging. A visual message shall be developed from any valid header... input. (8) Decoder Programming. Access to decoder programming shall be protected by a lock or other...

United States European Command

Science.gov Websites

content on the U.S. European Command website may be translated by selecting a different language on the header. Except where otherwise noted, the language translation is performed by Google Translate, a third

Search | Galaxy of Images

Science.gov Websites

Books dot header Search Tips Search Keywords in Author Last Name or in the Title of the Books: Enter a books Images FAQ | Privacy | SI Terms of Use | Smithsonian Home DCSIMG

Shape optimized headers and methods of manufacture thereof

DOEpatents

Perrin, Ian James

2013-11-05

Disclosed herein is a shape optimized header comprising a shell that is operative for collecting a fluid; wherein an internal diameter and/or a wall thickness of the shell vary with a change in pressure and/or a change in a fluid flow rate in the shell; and tubes; wherein the tubes are in communication with the shell and are operative to transfer fluid into the shell. Disclosed herein is a method comprising fixedly attaching tubes to a shell; wherein the shell is operative for collecting a fluid; wherein an internal diameter and/or a wall thickness of the shell vary with a change in pressure and/or a change in a fluid flow rate in the shell; and wherein the tubes are in communication with the shell and are operative to transfer fluid into the shell.

XAFS Data Interchange: A single spectrum XAFS data file format.

PubMed

Ravel, B; Newville, M

We propose a standard data format for the interchange of XAFS data. The XAFS Data Interchange (XDI) standard is meant to encapsulate a single spectrum of XAFS along with relevant metadata. XDI is a text-based format with a simple syntax which clearly delineates metadata from the data table in a way that is easily interpreted both by a computer and by a human. The metadata header is inspired by the format of an electronic mail header, representing metadata names and values as an associative array. The data table is represented as columns of numbers. This format can be imported as is into most existing XAFS data analysis, spreadsheet, or data visualization programs. Along with a specification and a dictionary of metadata types, we provide an application-programming interface written in C and bindings for programming dynamic languages.

XAFS Data Interchange: A single spectrum XAFS data file format

NASA Astrophysics Data System (ADS)

Ravel, B.; Newville, M.

2016-05-01

We propose a standard data format for the interchange of XAFS data. The XAFS Data Interchange (XDI) standard is meant to encapsulate a single spectrum of XAFS along with relevant metadata. XDI is a text-based format with a simple syntax which clearly delineates metadata from the data table in a way that is easily interpreted both by a computer and by a human. The metadata header is inspired by the format of an electronic mail header, representing metadata names and values as an associative array. The data table is represented as columns of numbers. This format can be imported as is into most existing XAFS data analysis, spreadsheet, or data visualization programs. Along with a specification and a dictionary of metadata types, we provide an application-programming interface written in C and bindings for programming dynamic languages.

Monte Carlo Uncertainty Quantification for an Unattended Enrichment Monitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jarman, Kenneth D.; Smith, Leon E.; Wittman, Richard S.

As a case study for uncertainty analysis, we consider a model flow monitor for measuring enrichment in gas centrifuge enrichment plants (GCEPs) that could provide continuous monitoring of all declared gas flow and provide high-accuracy gas enrichment estimates as a function of time. The monitor system could include NaI(Tl) gamma-ray spectrometers, a pressure signal-sharing device to be installed on an operator\\rq{}s pressure gauge or a dedicated inspector pressure sensor, and temperature sensors attached to the outside of the header pipe, to provide pressure, temperature, and gamma-ray spectra measurements of UFmore » $$_6$$ gas flow through unit header pipes. Our study builds on previous modeling and analysis methods development for enrichment monitor concepts and a software tool that was developed at Oak Ridge National Laboratory to generate and analyze synthetic data.« less

Network acceleration techniques

NASA Technical Reports Server (NTRS)

Crowley, Patricia (Inventor); Maccabe, Arthur Barney (Inventor); Awrach, James Michael (Inventor)

2012-01-01

Splintered offloading techniques with receive batch processing are described for network acceleration. Such techniques offload specific functionality to a NIC while maintaining the bulk of the protocol processing in the host operating system ("OS"). The resulting protocol implementation allows the application to bypass the protocol processing of the received data. Such can be accomplished this by moving data from the NIC directly to the application through direct memory access ("DMA") and batch processing the receive headers in the host OS when the host OS is interrupted to perform other work. Batch processing receive headers allows the data path to be separated from the control path. Unlike operating system bypass, however, the operating system still fully manages the network resource and has relevant feedback about traffic and flows. Embodiments of the present disclosure can therefore address the challenges of networks with extreme bandwidth delay products (BWDP).

Zero-Copy Objects System

NASA Technical Reports Server (NTRS)

Burleigh, Scott C.

2011-01-01

Zero-Copy Objects System software enables application data to be encapsulated in layers of communication protocol without being copied. Indirect referencing enables application source data, either in memory or in a file, to be encapsulated in place within an unlimited number of protocol headers and/or trailers. Zero-copy objects (ZCOs) are abstract data access representations designed to minimize I/O (input/output) in the encapsulation of application source data within one or more layers of communication protocol structure. They are constructed within the heap space of a Simple Data Recorder (SDR) data store to which all participating layers of the stack must have access. Each ZCO contains general information enabling access to the core source data object (an item of application data), together with (a) a linked list of zero or more specific extents that reference portions of this source data object, and (b) linked lists of protocol header and trailer capsules. The concatenation of the headers (in ascending stack sequence), the source data object extents, and the trailers (in descending stack sequence) constitute the transmitted data object constructed from the ZCO. This scheme enables a source data object to be encapsulated in a succession of protocol layers without ever having to be copied from a buffer at one layer of the protocol stack to an encapsulating buffer at a lower layer of the stack. For large source data objects, the savings in copy time and reduction in memory consumption may be considerable.

49 CFR 192.155 - Welded branch connections.

Code of Federal Regulations, 2010 CFR

2010-10-01

... not reduced, taking into account the stresses in the remaining pipe wall due to the opening in the pipe or header, the shear stresses produced by the pressure acting on the area of the branch opening...

19 CFR 10.223 - Articles eligible for preferential treatment.

Code of Federal Regulations, 2010 CFR

2010-04-01

... “sleeve header,” of woven or weft-inserted warp knit construction and of coarse animal hair or man-made... expenses incurred in the growth, production, manufacture, or other processing of the components, findings...

19 CFR 10.223 - Articles eligible for preferential treatment.

Code of Federal Regulations, 2014 CFR

2014-04-01

... “sleeve header,” of woven or weft-inserted warp knit construction and of coarse animal hair or man-made... expenses incurred in the growth, production, manufacture, or other processing of the components, findings...

19 CFR 10.223 - Articles eligible for preferential treatment.

Code of Federal Regulations, 2011 CFR

2011-04-01

... “sleeve header,” of woven or weft-inserted warp knit construction and of coarse animal hair or man-made... expenses incurred in the growth, production, manufacture, or other processing of the components, findings...

19 CFR 10.223 - Articles eligible for preferential treatment.

Code of Federal Regulations, 2012 CFR

2012-04-01

... “sleeve header,” of woven or weft-inserted warp knit construction and of coarse animal hair or man-made... expenses incurred in the growth, production, manufacture, or other processing of the components, findings...

19 CFR 10.223 - Articles eligible for preferential treatment.

Code of Federal Regulations, 2013 CFR

2013-04-01

... “sleeve header,” of woven or weft-inserted warp knit construction and of coarse animal hair or man-made... expenses incurred in the growth, production, manufacture, or other processing of the components, findings...

49 CFR 192.155 - Welded branch connections.

Code of Federal Regulations, 2012 CFR

2012-10-01

... not reduced, taking into account the stresses in the remaining pipe wall due to the opening in the pipe or header, the shear stresses produced by the pressure acting on the area of the branch opening...

49 CFR 192.155 - Welded branch connections.

Code of Federal Regulations, 2013 CFR

2013-10-01

... not reduced, taking into account the stresses in the remaining pipe wall due to the opening in the pipe or header, the shear stresses produced by the pressure acting on the area of the branch opening...

46 CFR 38.20-1 - Venting-T/ALL.

Code of Federal Regulations, 2010 CFR

2010-10-01

... pressure of 10 percent of the relief valve setting is insufficient to move the gases through any but an...) Vents and headers shall be so installed as to prevent excessive stresses on safety relief valve...

46 CFR 38.20-1 - Venting-T/ALL.

Code of Federal Regulations, 2014 CFR

2014-10-01

... pressure of 10 percent of the relief valve setting is insufficient to move the gases through any but an...) Vents and headers shall be so installed as to prevent excessive stresses on safety relief valve...

46 CFR 38.20-1 - Venting-T/ALL.

Code of Federal Regulations, 2011 CFR

2011-10-01

... pressure of 10 percent of the relief valve setting is insufficient to move the gases through any but an...) Vents and headers shall be so installed as to prevent excessive stresses on safety relief valve...

46 CFR 38.20-1 - Venting-T/ALL.

Code of Federal Regulations, 2012 CFR

2012-10-01

... pressure of 10 percent of the relief valve setting is insufficient to move the gases through any but an...) Vents and headers shall be so installed as to prevent excessive stresses on safety relief valve...

46 CFR 38.20-1 - Venting-T/ALL.

Code of Federal Regulations, 2013 CFR

2013-10-01

... pressure of 10 percent of the relief valve setting is insufficient to move the gases through any but an...) Vents and headers shall be so installed as to prevent excessive stresses on safety relief valve...

49 CFR 192.155 - Welded branch connections.

Code of Federal Regulations, 2011 CFR

2011-10-01

... not reduced, taking into account the stresses in the remaining pipe wall due to the opening in the pipe or header, the shear stresses produced by the pressure acting on the area of the branch opening...

47 CFR 11.54 - EAS operation during a National Level emergency.

Code of Federal Regulations, 2010 CFR

2010-10-01

... licensees and DBS providers may choose their two EAS sources, one of which must be a PEP station. (2... header codes for a national emergency. (3) After completing the above transmission procedures, key EAS...

47 CFR 11.54 - EAS operation during a National Level emergency.

Code of Federal Regulations, 2011 CFR

2011-10-01

... licensees and DBS providers may choose their two EAS sources, one of which must be a PEP station. (2... header codes for a national emergency. (3) After completing the above transmission procedures, key EAS...

Evaluating two process scale chromatography column header designs using CFD.

PubMed

Johnson, Chris; Natarajan, Venkatesh; Antoniou, Chris

2014-01-01

Chromatography is an indispensable unit operation in the downstream processing of biomolecules. Scaling of chromatographic operations typically involves a significant increase in the column diameter. At this scale, the flow distribution within a packed bed could be severely affected by the distributor design in process scale columns. Different vendors offer process scale columns with varying design features. The effect of these design features on the flow distribution in packed beds and the resultant effect on column efficiency and cleanability needs to be properly understood in order to prevent unpleasant surprises on scale-up. Computational Fluid Dynamics (CFD) provides a cost-effective means to explore the effect of various distributor designs on process scale performance. In this work, we present a CFD tool that was developed and validated against experimental dye traces and tracer injections. Subsequently, the tool was employed to compare and contrast two commercially available header designs. © 2014 American Institute of Chemical Engineers.

DARPA TIMIT acoustic-phonetic continous speech corpus CD-ROM. NIST speech disc 1-1.1

NASA Astrophysics Data System (ADS)

Garofolo, J. S.; Lamel, L. F.; Fisher, W. M.; Fiscus, J. G.; Pallett, D. S.

1993-02-01

The Texas Instruments/Massachusetts Institute of Technology (TIMIT) corpus of read speech has been designed to provide speech data for the acquisition of acoustic-phonetic knowledge and for the development and evaluation of automatic speech recognition systems. TIMIT contains speech from 630 speakers representing 8 major dialect divisions of American English, each speaking 10 phonetically-rich sentences. The TIMIT corpus includes time-aligned orthographic, phonetic, and word transcriptions, as well as speech waveform data for each spoken sentence. The release of TIMIT contains several improvements over the Prototype CD-ROM released in December, 1988: (1) full 630-speaker corpus, (2) checked and corrected transcriptions, (3) word-alignment transcriptions, (4) NIST SPHERE-headered waveform files and header manipulation software, (5) phonemic dictionary, (6) new test and training subsets balanced for dialectal and phonetic coverage, and (7) more extensive documentation.

Proposed U.S. Geological Survey standard for digital orthophotos

USGS Publications Warehouse

Hooper, David; Caruso, Vincent

1991-01-01

The U.S. Geological Survey has added the new category of digital orthophotos to the National Digital Cartographic Data Base. This differentially rectified digital image product enables users to take advantage of the properties of current photoimagery as a source of geographic information. The product and accompanying standard were implemented in spring 1991. The digital orthophotos will be quadrangle based and cast on the Universal Transverse Mercator projection and will extend beyond the 3.75-minute or 7.5-minute quadrangle area at least 300 meters to form a rectangle. The overedge may be used for mosaicking with adjacent digital orthophotos. To provide maximum information content and utility to the user, metadata (header) records exist at the beginning of the digital orthophoto file. Header information includes the photographic source type, date, instrumentation used to create the digital orthophoto, and information relating to the DEM that was used in the rectification process. Additional header information is included on transformation constants from the 1927 and 1983 North American Datums to the orthophoto internal file coordinates to enable the user to register overlays on either datum. The quadrangle corners in both datums are also imprinted on the image. Flexibility has been built into the digital orthophoto format for future enhancements, such as the provision to include the corresponding digital elevation model elevations used to rectify the orthophoto. The digital orthophoto conforms to National Map Accuracy Standards and provides valuable mapping data that can be used as a tool for timely revision of standard map products, for land use and land cover studies, and as a digital layer in a geographic information system.

Lidar - ND Halo Scanning Doppler, Boardman - Raw Data

DOE Office of Scientific and Technical Information (OSTI.GOV)

Leo, Laura

2017-10-23

The University of Notre Dame (ND) scanning lidar dataset used for the WFIP2 Campaign is provided. The raw dataset contains the radial velocity and backscatter measurements along with the beam location and other lidar parameters in the header.

Trick Simulation Environment 07

NASA Technical Reports Server (NTRS)

Lin, Alexander S.; Penn, John M.

2012-01-01

The Trick Simulation Environment is a generic simulation toolkit used for constructing and running simulations. This release includes a Monte Carlo analysis simulation framework and a data analysis package. It produces all auto documentation in XML. Also, the software is capable of inserting a malfunction at any point during the simulation. Trick 07 adds variable server output options and error messaging and is capable of using and manipulating wide characters for international support. Wide character strings are available as a fundamental type for variables processed by Trick. A Trick Monte Carlo simulation uses a statistically generated, or predetermined, set of inputs to iteratively drive the simulation. Also, there is a framework in place for optimization and solution finding where developers may iteratively modify the inputs per run based on some analysis of the outputs. The data analysis package is capable of reading data from external simulation packages such as MATLAB and Octave, as well as the common comma-separated values (CSV) format used by Excel, without the use of external converters. The file formats for MATLAB and Octave were obtained from their documentation sets, and Trick maintains generic file readers for each format. XML tags store the fields in the Trick header comments. For header files, XML tags for structures and enumerations, and the members within are stored in the auto documentation. For source code files, XML tags for each function and the calling arguments are stored in the auto documentation. When a simulation is built, a top level XML file, which includes all of the header and source code XML auto documentation files, is created in the simulation directory. Trick 07 provides an XML to TeX converter. The converter reads in header and source code XML documentation files and converts the data to TeX labels and tables suitable for inclusion in TeX documents. A malfunction insertion capability allows users to override the value of any simulation variable, or call a malfunction job, at any time during the simulation. Users may specify conditions, use the return value of a malfunction trigger job, or manually activate a malfunction. The malfunction action may consist of executing a block of input file statements in an action block, setting simulation variable values, call a malfunction job, or turn on/off simulation jobs.

Use of tear ring permits repair of sealed module circuitry

NASA Technical Reports Server (NTRS)

1965-01-01

Improved packaging technique for modular electronic circuitry utilizes a tear ring which may be removed for repair and resealed. The tear ring is put over the container and header to which the electronic circuit assembly has been attached.

Measured Plume Dispersion Parameters Over Water. Volume 1.

DTIC Science & Technology

1984-09-01

meteorlogical parameters were continuously monitored at various locations. Tracer gas concentrations were measured by a variety of methods at...addition, this step added a header . to the data set containing a variety of averaged meteorlogical quantities. The basic procedure in this step was

Space Wire Upper Layer Protocols

NASA Technical Reports Server (NTRS)

Rakow, Glenn; Schnurr, Richard; Gilley, Daniel; Parkes, Steve

2004-01-01

This viewgraph presentation addresses efforts to provide a streamlined approach for developing SpaceWire Upper layer protocols which allows industry to drive standardized communication solutions for real projects. The presentation proposes a simple packet header that will allow flexibility in implementing a diverse range of protocols.

Enterprise-scale image distribution with a Web PACS.

PubMed

Gropper, A; Doyle, S; Dreyer, K

1998-08-01

The integration of images with existing and new health care information systems poses a number of challenges in a multi-facility network: image distribution to clinicians; making DICOM image headers consistent across information systems; and integration of teleradiology into PACS. A novel, Web-based enterprise PACS architecture introduced at Massachusetts General Hospital provides a solution. Four AMICAS Web/Intranet Image Servers were installed as the default DICOM destination of 10 digital modalities. A fifth AMICAS receives teleradiology studies via the Internet. Each AMICAS includes: a Java-based interface to the IDXrad radiology information system (RIS), a DICOM autorouter to tape-library archives and to the Agfa PACS, a wavelet image compressor/decompressor that preserves compatibility with DICOM workstations, a Web server to distribute images throughout the enterprise, and an extensible interface which permits links between other HIS and AMICAS. Using wavelet compression and Internet standards as its native formats, AMICAS creates a bridge to the DICOM networks of remote imaging centers via the Internet. This teleradiology capability is integrated into the DICOM network and the PACS thereby eliminating the need for special teleradiology workstations. AMICAS has been installed at MGH since March of 1997. During that time, it has been a reliable component of the evolving digital image distribution system. As a result, the recently renovated neurosurgical ICU will be filmless and use only AMICAS workstations for mission-critical patient care.

More flexibility in representing geometric distortion in astronomical images

NASA Astrophysics Data System (ADS)

Shupe, David L.; Laher, Russ R.; Storrie-Lombardi, Lisa; Surace, Jason; Grillmair, Carl; Levitan, David; Sesar, Branimir

2012-09-01

A number of popular software tools in the public domain are used by astronomers, professional and amateur alike, but some of the tools that have similar purposes cannot be easily interchanged, owing to the lack of a common standard. For the case of image distortion, SCAMP and SExtractor, available from Astromatic.net, perform astrometric calibration and source-object extraction on image data, and image-data geometric distortion is computed in celestial coordinates with polynomial coefficients stored in the FITS header with the PV i_j keywords. Another widely-used astrometric-calibration service, Astrometry.net, solves for distortion in pixel coordinates using the SIP convention that was introduced by the Spitzer Science Center. Up until now, due to the complexity of these distortion representations, it was very difficult to use the output of one of these packages as input to the other. New Python software, along with faster-computing C-language translations, have been developed at the Infrared Processing and Analysis Center (IPAC) to convert FITS-image headers from PV to SIP and vice versa. It is now possible to straightforwardly use Astrometry.net for astrometric calibration and then SExtractor for source-object extraction. The new software also enables astrometric calibration by SCAMP followed by image visualization with tools that support SIP distortion, but not PV . The software has been incorporated into the image-processing pipelines of the Palomar Transient Factory (PTF), which generate FITS images with headers containing both distortion representations. The software permits the conversion of archived images, such as from the Spitzer Heritage Archive and NASA/IPAC Infrared Science Archive, from SIP to PV or vice versa. This new capability renders unnecessary any new representation, such as the proposed TPV distortion convention.

SCORE user`s manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, S.A.

SABrE is a set of tools to facilitate the development of portable scientific software and to visualize scientific data. As with most constructs, SABRE has a foundation. In this case that foundation is SCORE. SCORE (SABRE CORE) has two main functions. The first and perhaps most important is to smooth over the differences between different C implementations and define the parameters which drive most of the conditional compilations in the rest of SABRE. Secondly, it contains several groups of functionality that are used extensively throughout SABRE. Although C is highly standardized now, that has not always been the case. Roughlymore » speaking C compilers fall into three categories: ANSI standard; derivative of the Portable C Compiler (Kernighan and Ritchie); and the rest. SABRE has been successfully ported to many ANSI and PCC systems. It has never been successfully ported to a system in the last category. The reason is mainly that the ``standard`` C library supplied with such implementations is so far from true ANSI or PCC standard that SABRE would have to include its own version of the standard C library in order to work at all. Even with standardized compilers life is not dead simple. The ANSI standard leaves several crucial points ambiguous as ``implementation defined.`` Under these conditions one can find significant differences in going from one ANSI standard compiler to another. SCORE`s job is to include the requisite standard headers and ensure that certain key standard library functions exist and function correctly (there are bugs in the standard library functions supplied with some compilers) so that, to applications which include the SCORE header(s) and load with SCORE, all C implementations look the same.« less

SCORE user's manual

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brown, S.A.

SABrE is a set of tools to facilitate the development of portable scientific software and to visualize scientific data. As with most constructs, SABRE has a foundation. In this case that foundation is SCORE. SCORE (SABRE CORE) has two main functions. The first and perhaps most important is to smooth over the differences between different C implementations and define the parameters which drive most of the conditional compilations in the rest of SABRE. Secondly, it contains several groups of functionality that are used extensively throughout SABRE. Although C is highly standardized now, that has not always been the case. Roughlymore » speaking C compilers fall into three categories: ANSI standard; derivative of the Portable C Compiler (Kernighan and Ritchie); and the rest. SABRE has been successfully ported to many ANSI and PCC systems. It has never been successfully ported to a system in the last category. The reason is mainly that the standard'' C library supplied with such implementations is so far from true ANSI or PCC standard that SABRE would have to include its own version of the standard C library in order to work at all. Even with standardized compilers life is not dead simple. The ANSI standard leaves several crucial points ambiguous as implementation defined.'' Under these conditions one can find significant differences in going from one ANSI standard compiler to another. SCORE's job is to include the requisite standard headers and ensure that certain key standard library functions exist and function correctly (there are bugs in the standard library functions supplied with some compilers) so that, to applications which include the SCORE header(s) and load with SCORE, all C implementations look the same.« less

The effect of heat sinks in GTA microwelding

DOE Office of Scientific and Technical Information (OSTI.GOV)

Knorovsky, G.A.; Burchett, S.N.

1989-01-01

When miniature devices containing glass-to-metal seals are closure welded it is accepted practice to incorporate thermal heat sinks into the fixturing. This is intended to assure that the heat from gas tungsten arc (GTA) welding will not cause thermal stress-induced cracking of the seals and loss of hermeticity. The design of these heat sinks has never been systematically studied; instead only ''engineering horse sense'' has been applied. This practice has been successful in the past; however, the component being GTA welded have become smaller and more complex (i.e., more pins) and glass cracking problems are being encountered. The technology ofmore » producing glass seal-containing lids (called ''headers'') has benefited from finite element analyses in deciding how to optimally dimension pin-to-glass seal diameter ratios and glass-to-metal thickness ratios in order to minimize thermal stresses locked in during manufacture. It appeared likely that an analysts of the stresses generated by welding would also be beneficial. Recently, computer speed and code capabilities have increased to the point where finite element analysis of a close simulation of real hardware can be made, including the effect of external heat sinks. The work reported here involves an analysis (with some supporting experimental data) of a miniature thermal battery which encountered glass cracking problems. In the course of the analysis various heat sink practices were examined. Among other findings, through-thickness thermal gradients in a header with a heat sink were found to equal in-plane thermal gradients in a header without any heat sinking at the glass seal positions. Also noted were significant variations due to relatively minor changes in the weld preparation geometry. A summary of good practice for heat sinking will be presented. 4 refs., 6 figs., 2 tabs.« less

Aviation and Airports, Transportation & Public Facilities, State of Alaska

Science.gov Websites

State Employees Alaska Department of Transportation & Public Facilities header image Alaska Department of Transportation & Public Facilities / Aviation and Airports Search DOT&PF State of Stevens Anchorage International Airport Link to List of Alaska Public Airports Ketchikan International

40 CFR 205.173-2 - Tampering.

Code of Federal Regulations, 2010 CFR

2010-07-01

... removal or puncturing the muffler, baffles, header pipes, or any other component which conducts exhaust... EQUIPMENT NOISE EMISSION CONTROLS Motorcycle Exhaust Systems § 205.173-2 Tampering. The manufacturer must... exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle...

Interior view, Slave Quarter/Service, second floor, detail view of framing ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

Interior view, Slave Quarter/Service, second floor, detail view of framing to show joists (with ghosts of lathe) and header (trimmer) with keyed through tenon. - Decatur House, National Trust for Historic Preservation, 748 Jackson Place Northwest, Washington, District of Columbia, DC

14. Interior, boiler house, at elev. 42'8' looking west at ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

14. Interior, boiler house, at elev. 42'-8' looking west at distribution headers and coal and oil burners of retired 300 lb. boilers #11, 10, and 9. - Manchester Street Generating Station, Manchester Street Station, 460 Eddy Street, Providence, Providence County, RI

Loop-Extended Symbolic Execution on Binary Programs

DTIC Science & Technology

2009-03-02

1434. Based on its speci- fication [35], one valid message format contains 2 fields: a header byte of value 4, followed by a string giving a database ...potentially become expensive. For instance the polyhedron technique [16] requires costly conversion operations on a multi-dimensional abstract representation

A Ceramic Heat Exchanger for Solar Receivers

NASA Technical Reports Server (NTRS)

Robertson Jr., C.; Stacy, L.

1985-01-01

Design intended for high-temperature service. Proposed ceramic-tube and header heat exchangers used for solar-concentrating collector operating in 25- to 150-KW power range at temperatures between 2,000 degrees and 3,000 degrees F (1,095 degrees and 1,650 degrees C).

Improved fabrication of electrolytic capacitors

NASA Technical Reports Server (NTRS)

Gamari, F. J.; Moresi, J. L.

1975-01-01

After processing parts for assembly, insulative cup is fitted to bottom of can, then electrolytic solution consisting of white sulfuric acid gel is inserted into can. Pellet is put in can and is fitted tightly into cup. Finally, bead weld is formed between can and header plug.

49 CFR 192.167 - Compressor stations: Emergency shutdown.

Code of Federal Regulations, 2011 CFR

2011-10-01

... Components § 192.167 Compressor stations: Emergency shutdown. (a) Except for unattended field compressor... fires, and electrical facilities in the vicinity of gas headers and in the compressor building, except that: (i) Electrical circuits that supply emergency lighting required to assist station personnel in...

49 CFR 192.167 - Compressor stations: Emergency shutdown.

Code of Federal Regulations, 2010 CFR

2010-10-01

... Components § 192.167 Compressor stations: Emergency shutdown. (a) Except for unattended field compressor... fires, and electrical facilities in the vicinity of gas headers and in the compressor building, except that: (i) Electrical circuits that supply emergency lighting required to assist station personnel in...

106-17 Telemetry Standards Recorder Data Packet Format Standard Chapter 11

DTIC Science & Technology

2017-07-01

11.2.2 PCM Data Packets ..................................................................................... 11-11 11.2.3 Time Data Packets...11-95 11.2.15 Ethernet Data Packets ................................................................................ 11-97 11.2.16 Time Space...4 Time ............................................................ 11-10 Figure 11-5. Secondary Header IEEE 1588 Time

A Distributed Data-Gathering Protocol Using AUV in Underwater Sensor Networks.

PubMed

Khan, Jawaad Ullah; Cho, Ho-Shin

2015-08-06

In this paper, we propose a distributed data-gathering scheme using an autonomous underwater vehicle (AUV) working as a mobile sink to gather data from a randomly distributed underwater sensor network where sensor nodes are clustered around several cluster headers. Unlike conventional data-gathering schemes where the AUV visits either every node or every cluster header, the proposed scheme allows the AUV to visit some selected nodes named path-nodes in a way that reduces the overall transmission power of the sensor nodes. Monte Carlo simulations are performed to investigate the performance of the proposed scheme compared with several preexisting techniques employing the AUV in terms of total amount of energy consumption, standard deviation of each node's energy consumption, latency to gather data at a sink, and controlling overhead. Simulation results show that the proposed scheme not only reduces the total energy consumption but also distributes the energy consumption more uniformly over the network, thereby increasing the lifetime of the network.

A Distributed Data-Gathering Protocol Using AUV in Underwater Sensor Networks

PubMed Central

Khan, Jawaad Ullah; Cho, Ho-Shin

2015-01-01

In this paper, we propose a distributed data-gathering scheme using an autonomous underwater vehicle (AUV) working as a mobile sink to gather data from a randomly distributed underwater sensor network where sensor nodes are clustered around several cluster headers. Unlike conventional data-gathering schemes where the AUV visits either every node or every cluster header, the proposed scheme allows the AUV to visit some selected nodes named path-nodes in a way that reduces the overall transmission power of the sensor nodes. Monte Carlo simulations are performed to investigate the performance of the proposed scheme compared with several preexisting techniques employing the AUV in terms of total amount of energy consumption, standard deviation of each node’s energy consumption, latency to gather data at a sink, and controlling overhead. Simulation results show that the proposed scheme not only reduces the total energy consumption but also distributes the energy consumption more uniformly over the network, thereby increasing the lifetime of the network. PMID:26287189

Internet-based interface for STRMDEPL08

USGS Publications Warehouse

Reeves, Howard W.; Asher, A. Jeremiah

2010-01-01

The core of the computer program STRMDEPL08 that estimates streamflow depletion by a pumping well with one of four analytical solutions was re-written in the Javascript software language and made available through an internet-based interface (web page). In the internet-based interface, the user enters data for one of the four analytical solutions, Glover and Balmer (1954), Hantush (1965), Hunt (1999), and Hunt (2003), and the solution is run for constant pumping for a desired number of simulation days. Results are returned in tabular form to the user. For intermittent pumping, the interface allows the user to request that the header information for an input file for the stand-alone executable STRMDEPL08 be created. The user would add the pumping information to this header information and run the STRMDEPL08 executable that is available for download through the U.S. Geological Survey. Results for the internet-based and stand-alone versions of STRMDEPL08 are shown to match.

Electric arc welding gun

DOEpatents

Luttrell, Edward; Turner, Paul W.

1978-01-01

This invention relates to improved apparatus for arc welding an interior joint formed by intersecting tubular members. As an example, the invention is well suited for applications where many similar small-diameter vertical lines are to be welded to a long horizontal header. The improved apparatus includes an arc welding gun having a specially designed welding head which is not only very compact but also produces welds that are essentially free from rolled-over solidified metal. The welding head consists of the upper end of the barrel and a reversely extending electrode holder, or tip, which defines an acute angle with the barrel. As used in the above-mentioned example, the gun is positioned to extend upwardly through the vertical member and the joint to be welded, with its welding head disposed within the horizontal header. Depending on the design of the welding head, the barrel then is either rotated or revolved about the axis of the vertical member to cause the electrode to track the joint.

Performance of LI-1542 reusable surface insulation system in a hypersonic stream

NASA Technical Reports Server (NTRS)

Hunt, L. R.; Bohon, H. L.

1974-01-01

The thermal and structural performance of a large panel of LI-1542 reusable surface insulation tiles was determined by a series of cyclic heating tests using radiant lamps and aerothemal tests in the Langley 8-foot high-temperature structures tunnel. Aerothermal tests were conducted at a free-stream Mach number of 6.6, a total temperature of 1830 K, Reynolds numbers of 2.0 and 4,900,000 per meter, and dynamic pressures of 29 and 65 kPa. The results suggest that pressure gradients in gaps and flow impingement on the header walls at the end of longitudinal gaps are sources for increased gap heating. Temperatures higher than surface radiation equilibrium temperature were measured deep in gaps and at the header walls. Also, the damage tolerance of the LI-1542 tiles appears to be very high. Tile edge erosion rate was slow; could not be tolerated in a shuttle application. Tiles soaked with water and subjected to rapid depressurization and aerodynamic heating showed no visible evidence of damage.

Validation and calibration of HeadCount, a self-report measure for quantifying heading exposure in soccer players.

PubMed

Catenaccio, E; Caccese, J; Wakschlag, N; Fleysher, R; Kim, N; Kim, M; Buckley, T A; Stewart, W F; Lipton, R B; Kaminski, T; Lipton, M L

2016-01-01

The long-term effects of repetitive head impacts due to heading are an area of increasing concern, and exposure must be accurately measured; however, the validity of self-report of cumulative soccer heading is not known. In order to validate HeadCount, a 2-week recall questionnaire, the number of player-reported headers was compared to the number of headers observed by trained raters for a men's and a women's collegiate soccer teams during an entire season of competitive play using Spearman's correlations and intraclass correlation coefficients (ICCs), and calibrated using a generalized estimating equation. The average Spearman's rho was 0.85 for men and 0.79 for women. The average ICC was 0.75 in men and 0.38 in women. The calibration analysis demonstrated that men tend to report heading accurately while women tend to overestimate. HeadCount is a valid instrument for tracking heading behaviour, but may have to be calibrated in women.

The PKI collector

NASA Astrophysics Data System (ADS)

Rice, M. P.

1982-07-01

The design and manufacturing of a solar thermal collector is discussed. The collector has three primary subsystems: concentrator, receiver/fluid loop, and controls. Identical curved reflective columns are utilized in a faceted Fresnel design to support 864 one foot square flat inexpensive second-surface, silvered glass mirrors. The columns are ganged together and rotated through their centers of gravity to provide elevation tracking. The concentrator is supported by a lightweight spaceframe structure which distributes all wind and gravity loads to the base supports. The base of the structure is a track which rotates on wheels mounted on concrete piers. A parallel tube steel heat exchanger is mounted at the concentrator focal area in a well insulated, galvanized steel housing. Two rows of vertical close-packed, staggered tubes connect a mud header and a steam header. Automatic two axis tracking and operational control is provided with a microprocessor based package. Concentrator-mounted shadowbands are the basis for active tracking. A software program provides azimuthal tracking during cloudy periods.

The PKI collector

NASA Technical Reports Server (NTRS)

Rice, M. P.

1982-01-01

The design and manufacturing of a solar thermal collector is discussed. The collector has three primary subsystems: concentrator, receiver/fluid loop, and controls. Identical curved reflective columns are utilized in a faceted Fresnel design to support 864 one foot square flat inexpensive second-surface, silvered glass mirrors. The columns are ganged together and rotated through their centers of gravity to provide elevation tracking. The concentrator is supported by a lightweight spaceframe structure which distributes all wind and gravity loads to the base supports. The base of the structure is a track which rotates on wheels mounted on concrete piers. A parallel tube steel heat exchanger is mounted at the concentrator focal area in a well insulated, galvanized steel housing. Two rows of vertical close-packed, staggered tubes connect a mud header and a steam header. Automatic two axis tracking and operational control is provided with a microprocessor based package. Concentrator-mounted shadowbands are the basis for active tracking. A software program provides azimuthal tracking during cloudy periods.

A New Archive of UKIRT Legacy Data at CADC

NASA Astrophysics Data System (ADS)

Bell, G. S.; Currie, M. J.; Redman, R. O.; Purves, M.; Jenness, T.

2014-05-01

We describe a new archive of legacy data from the United Kingdom Infrared Telescope (UKIRT) at the Canadian Astronomy Data Centre (CADC) containing all available data from the Cassegrain instruments. The desire was to archive the raw data in as close to the original format as possible, so where the data followed our current convention of having a single data file per observation, it was archived without alteration, except for minor fixes to headers of data in FITS format to allow it to pass fitsverify and be accepted by CADC. Some of the older data comprised multiple integrations in separate files per observation, stored in either Starlink NDF or Figaro DST format. These were placed inside HDS container files, and DST files were rearranged into NDF format. The describing the observations is ingested into the CAOM-2 repository via an intermediate MongoDB header database, which will also be used to guide the ORAC-DR pipeline in generating reduced data products.

Hollow Fiber Ground Evaporator Unit Testing

NASA Technical Reports Server (NTRS)

Bue, Grant; Trevino, Luis; Tsioulos, Gus

2010-01-01

A candidate technology for 1-atmosphere suited heat rejection was developed and tested at NASA Johnson Space Center. The concept is to use a collection of microporous hydrophobic tubes potted between inlet and outlet headers with water as coolant. A pump provides flow between headers through the tubes which are subjected to fan driven cross flow of relatively dry air. The forced ventilation would sweep out the water vapor from the evaporation of the coolant rejecting heat from the coolant stream. The hollow fibers are obtained commercially (X50-215 Celgard) which are arranged in a sheet containing 5 fibers per linear inch. Two engineering development units were produced that vary the fold direction of the fiber sheets relative to the ventilation. These units were tested at inlet water temperatures ranging from 20 deg C to 30 deg C, coolant flow rates ranging from 10 to 90 kg/hr, and at three fan speeds. These results were used to size a system that could reject heat at a rate of 340 W.

Charge coupled devices

NASA Technical Reports Server (NTRS)

Walker, J. W.; Hornbeck, L. J.; Stubbs, D. P.

1977-01-01

The results are presented of a program to design, fabricate, and test CCD arrays suitable for operation in an electron-bombarded mode. These intensified charge coupled devices have potential application to astronomy as photon-counting arrays. The objectives of this program were to deliver arrays of 250 lines of 400 pixels each and some associated electronics. Some arrays were delivered on tube-compatible headers and some were delivered after incorporation in vacuum tubes. Delivery of these devices required considerable improvements to be made in the processing associated with intensified operation. These improvements resulted in a high yield in the thinning process, reproducible results in the accumulation process, elimination of a dark current source in the accumulation process, solution of a number of header related problems, and the identification of a remaining major source of dark current. Two systematic failure modes were identified and protective measures established. The effects of tube processing on the arrays in the delivered ICCDs were determined and are reported along with the characterization data on the arrays.

XML Translator for Interface Descriptions

NASA Technical Reports Server (NTRS)

Boroson, Elizabeth R.

2009-01-01

A computer program defines an XML schema for specifying the interface to a generic FPGA from the perspective of software that will interact with the device. This XML interface description is then translated into header files for C, Verilog, and VHDL. User interface definition input is checked via both the provided XML schema and the translator module to ensure consistency and accuracy. Currently, programming used on both sides of an interface is inconsistent. This makes it hard to find and fix errors. By using a common schema, both sides are forced to use the same structure by using the same framework and toolset. This makes for easy identification of problems, which leads to the ability to formulate a solution. The toolset contains constants that allow a programmer to use each register, and to access each field in the register. Once programming is complete, the translator is run as part of the make process, which ensures that whenever an interface is changed, all of the code that uses the header files describing it is recompiled.

Nebraska DHHS: Swimming Pool Program

Science.gov Websites

Skip to main content Official Nebraska Government Website NE-DHHS Home Header Behavioral Health Children and Family Services Developmental Disabilities Medicaid and Long Term Care Public Health DHHS Internet Website - Public Health DHHS Internet Website - Public Health : Nebraska DHHS: Swimming Pool

Nebraska DHHS: What is Tuberculosis?

Science.gov Websites

Skip to main content Official Nebraska Government Website NE-DHHS Home Header Behavioral Health Children and Family Services Developmental Disabilities Medicaid and Long Term Care Public Health DHHS Internet Website - Public Health DHHS Internet Website - Public Health : Nebraska DHHS: What is

40 CFR 205.164 - Applicability.

Code of Federal Regulations, 2010 CFR

2010-07-01

... as defined in § 205.151(a)(3). (e) The provisions of the subpart do not apply to exhaust header pipes... EQUIPMENT NOISE EMISSION CONTROLS Motorcycle Exhaust Systems § 205.164 Applicability. (a) Except as... exhaust system or motorcycle replacement exhaust system component which: (1) Meets the definition of the...

Colorado Water Institute

Science.gov Websites

Colorado Water Institute Colorado State University header HomeMission StatementGRAD592NewslettersPublications/ReportsCSU Water ExpertsFunding OpportunitiesScholarshipsSubscribeEmploymentAdvisory BoardStaffContact UsCommentsLinks Water Center Logo Water Resources Archive Office of Engagement Ag Water

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2012 CFR

2012-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR § 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2013 CFR

2013-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2014 CFR

2014-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2010 CFR

2010-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

36 CFR 1237.28 - What special concerns apply to digital photographs?

Code of Federal Regulations, 2011 CFR

2011-07-01

... defects, evaluate the accuracy of finding aids, and verify file header information and file name integrity... sampling methods or more comprehensive verification systems (e.g., checksum programs), to evaluate image.... For permanent or unscheduled images descriptive elements must include: (1) An identification number...

--No Title--

Science.gov Websites

{background-color:#5e6a71;border-top:3px solid #62d2ff}@media (min-width: 768px){header{border-bottom:9px a.app-name:hover{color:#fff;display:block;font-family:Roboto;font-size:30px;line-height:1.2em;margin:0 0

Photoelastic analysis in respect to failure mechanics problems of power plant articles and units

NASA Astrophysics Data System (ADS)

Korikhin, N. V.; Eigenson, S. N.

2009-02-01

The results of strength tests of some critical articles and units of power plants, i.e., a reactor vessel, threaded connection of vessel split, pressure header with straight nipple, turbomachine shaft, and T-weld joint of stator and rotor parts, of turbomachines are presented.

Memory Forensics: Review of Acquisition and Analysis Techniques

DTIC Science & Technology

2013-11-01

Management Overview Processes running on modern multitasking operating systems operate on an abstraction of RAM, called virtual memory [7]. In these systems...information such as user names, email addresses and passwords [7]. Analysts also use tools such as WinHex to identify headers or other suspicious data within

International Metadata Initiatives: Lessons in Bibliographic Control.

ERIC Educational Resources Information Center

Caplan, Priscilla

This paper looks at a subset of metadata schemes, including the Text Encoding Initiative (TEI) header, the Encoded Archival Description (EAD), the Dublin Core Metadata Element Set (DCMES), and the Visual Resources Association (VRA) Core Categories for visual resources. It examines why they developed as they did, major point of difference from…

29 CFR 1926.350 - Gas welding and cutting.

Code of Federal Regulations, 2014 CFR

2014-07-01

... moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used to keep cylinders... enclosed spaces. (3) Manifold hose connections, including both ends of the supply hose that lead to the... supply header connections. Adapters shall not be used to permit the interchange of hose. Hose connections...

29 CFR 1926.350 - Gas welding and cutting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used to keep cylinders... enclosed spaces. (3) Manifold hose connections, including both ends of the supply hose that lead to the... supply header connections. Adapters shall not be used to permit the interchange of hose. Hose connections...

29 CFR 1926.350 - Gas welding and cutting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used to keep cylinders... enclosed spaces. (3) Manifold hose connections, including both ends of the supply hose that lead to the... supply header connections. Adapters shall not be used to permit the interchange of hose. Hose connections...

49 CFR 192.3 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-10-01

... header or manifold. SMYS means specified minimum yield strength is: (1) For steel pipe manufactured in... the waters from the mean high water mark of the coast of the Gulf of Mexico and its inlets open to the... water. High-pressure distribution system means a distribution system in which the gas pressure in the...

49 CFR 192.3 - Definitions.

Code of Federal Regulations, 2011 CFR

2011-10-01

... header or manifold. SMYS means specified minimum yield strength is: (1) For steel pipe manufactured in... the waters from the mean high water mark of the coast of the Gulf of Mexico and its inlets open to the... water. High-pressure distribution system means a distribution system in which the gas pressure in the...

49 CFR 192.3 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-10-01

... header or manifold. SMYS means specified minimum yield strength is: (1) For steel pipe manufactured in... the waters from the mean high water mark of the coast of the Gulf of Mexico and its inlets open to the... water. High-pressure distribution system means a distribution system in which the gas pressure in the...

49 CFR 192.3 - Definitions.

Code of Federal Regulations, 2014 CFR

2014-10-01

... header or manifold. SMYS means specified minimum yield strength is: (1) For steel pipe manufactured in... the waters from the mean high water mark of the coast of the Gulf of Mexico and its inlets open to the... water. High-pressure distribution system means a distribution system in which the gas pressure in the...

49 CFR 192.3 - Definitions.

Code of Federal Regulations, 2010 CFR

2010-10-01

... header or manifold. SMYS means specified minimum yield strength is: (1) For steel pipe manufactured in... the waters from the mean high water mark of the coast of the Gulf of Mexico and its inlets open to the... water. High-pressure distribution system means a distribution system in which the gas pressure in the...

46 CFR 59.10-5 - Cracks.

Code of Federal Regulations, 2011 CFR

2011-10-01

... does not exceed 12 inches in length and after completion the weld is stress-relieved. Cracks in... the shell of water tube boiler drums, provided there are not more than two cracks in any one row in... Commandant. (g) Cracks that occur in superheater manifolds, water wallheaders, water drums, sectional headers...

46 CFR 59.10-5 - Cracks.

Code of Federal Regulations, 2010 CFR

2010-10-01

... does not exceed 12 inches in length and after completion the weld is stress-relieved. Cracks in... the shell of water tube boiler drums, provided there are not more than two cracks in any one row in... Commandant. (g) Cracks that occur in superheater manifolds, water wallheaders, water drums, sectional headers...

Attribution of Spear Phishing Attacks: A Literature Survey

DTIC Science & Technology

2013-08-01

header of an email, verbally informed by another person, or easily ascertained via the handwriting of the text. In a few specific cases, this...scene would be scrutinised, based on both the handwriting and the content of the letter, to identify a suspect. The goal of this phase is to establish

Freedom Of Information Act

Science.gov Websites

Web Site Freedom of Information Act Sign In Freedom of Information Act Header Search this site ... Search Freedom of Information Act Introduction to FOIA Making A Request Points of Contact FOIA Reports Reading Room Frequently Asked Questions FOIA Links Privacy Act Requests Freedom Of Information (FOIA) &

Dismal: A Spreadsheet for Sequential Data Analysis and HCI Experimentation

DTIC Science & Technology

2002-01-24

Hambly, Alder, Wyatt- Millington, Shrayane, Crawshaw , et al., 1996). Table 2 provides some example data. An automatically generated header comes first...Shrayane, N. M., Crawshaw , C. M., & Hockey, G. R. J. (1996). Investigating the human-computer interface using the Datalogger. Behavior Research Methods, Instruments, & Computers, 28(4), 603-606.

Limited Area Coverage/High Resolution Picture Transmission (LAC/HRPT) tape IJ grid pixel extraction processor user's manual

NASA Technical Reports Server (NTRS)

Obrien, S. O. (Principal Investigator)

1980-01-01

The program, LACREG, extracted all pixels that are contained in a specific IJ grid section. The pixels, along with a header record are stored in a disk file defined by the user. The program will extract up to 99 IJ grid sections.

20. TYPICAL VIEW OF FRONT WINDOWS FROM 4TH TO 9TH ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

20. TYPICAL VIEW OF FRONT WINDOWS FROM 4TH TO 9TH FLOOR WITH WHITE GLAZED TERRA COTTA SILL AND HEADERS. MULLIONS ARE ORANGE BROWN BRICKS LIKE THE WALLS. BRICKS ARE IN FLEMISH BOND PATTERN. - Pacific Telephone & Telegraph Company Building, 1519 Franklin Street, Oakland, Alameda County, CA

--No Title--

Science.gov Websites

.navbar-nav .open .dropdown-menu { float: none; width: auto; margin-top: 0; background-color: transparent ; border: 0; box-shadow: none; } #topnav .navbar-nav .open .dropdown-menu > li > a, #topnav .navbar -nav .open .dropdown-menu .dropdown-header { padding: 10px 15px 10px 25px; } #topnav .navbar-nav .open

Modifications Caused by Enzyme-retting and Their Effect on Composite Performance

USDA-ARS?s Scientific Manuscript database

Bethune seed flax was collected from Canada with seed removed using a stripper header and straw pulled and left in field for several weeks. Unretted straw was decorticated providing a coarse fiber bundle feedstock for enzyme treatments. Enzyme treatments using a bacterial pectinolytic enzyme with ...

29 CFR 1915.55 - Gas welding and cutting.

Code of Federal Regulations, 2013 CFR

2013-07-01

... before cylinders are moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used... ends of the supply hose that lead to the manifold, shall be such that the hose cannot be interchanged between fuel gas and oxygen manifolds and supply header connections. Adapters shall not be used to permit...

29 CFR 1915.55 - Gas welding and cutting.

Code of Federal Regulations, 2012 CFR

2012-07-01

... before cylinders are moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used... ends of the supply hose that lead to the manifold, shall be such that the hose cannot be interchanged between fuel gas and oxygen manifolds and supply header connections. Adapters shall not be used to permit...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2011 CFR

2011-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR § 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2013 CFR

2013-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2014 CFR

2014-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2012 CFR

2012-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

36 CFR 1238.12 - What documentation is required for microfilmed records?

Code of Federal Regulations, 2010 CFR

2010-07-01

... microforms capture all information contained on the source documents and that they can be used for the... retrieval and use. Agencies must: (a) Arrange, describe, and index the filmed records to permit retrieval of... titling target or header. For fiche, place the titling information in the first frame if the information...

Weather. European Theater Weather Orientation (ETWO)

DTIC Science & Technology

1992-11-01

EGUL RAF Lakenheath KBKF Buckdey CO EGUN RAF Mildenhall KSAW Sawyer MI EDAS Sembach GM KGRF Ft Lewis WA EDAB Bitburg GM KFRI Ft Riley KS EDAT...Stability Idez (2) The following list shows the bulletin headers with stations included on each FJ•UEO EDEX EDIC EDIN EDOP EDID EDOT FUE51 EGUA EGUN

Sealing glasses for titanium and titanium alloys

DOEpatents

Brow, Richard K.; Watkins, Randall D.

1992-01-01

Glass compositions containing CaO, Al.sub.2 O.sub.3, B.sub.2 O.sub.3, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

Sealing glasses for titanium and titanium alloys

DOEpatents

Brow, R.K.; Watkins, R.D.

1988-01-21

Glass compositions containing CaO, Al/sub 2/O/sub 3/, B/sub 2/O/sub 3/, SrO and BaO of various combinations of mole % are provided. These compositions are capable of forming stable glass-to-metal seals with titanium and titanium alloys, for use in components such as seals for battery headers.

78 FR 15715 - Excelerate Liquefaction Solutions I, LLC; Lavaca Bay Pipeline System, LLC; Notice of Intent To...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-12

... natural gas from existing pipeline systems to the LNG terminal facilities. The Project would be... room, warehouse, and shop. Pipeline Header System: A 29-mile-long, 42-inch-diameter natural gas pipeline extending northward from the shoreside facilities to nine natural gas interconnects southwest of...

Epigenomics Reveals a Functional Genome Anatomy and a New Approach to Common Disease

PubMed Central

Feinberg, Andrew P.

2010-01-01

Standfirst header Epigenomics provides the functional context of genome sequence, analogous to the functional anatomy of the human body provided by Vesalius a half millennium ago. Much of what appear to be inconclusive genetic data for common disease could therefore become meaningful in an epigenomic context. PMID:20944596

46 CFR 154.517 - Piping: Liquid pressure relief.

Code of Federal Regulations, 2014 CFR

2014-10-01

... 46 Shipping 5 2014-10-01 2014-10-01 false Piping: Liquid pressure relief. 154.517 Section 154.517... and Process Piping Systems § 154.517 Piping: Liquid pressure relief. The cargo loading and discharge crossover headers, cargo hoses, and cargo loading arms must have means to relieve cargo pressure and to...

46 CFR 154.517 - Piping: Liquid pressure relief.

Code of Federal Regulations, 2013 CFR

2013-10-01

... 46 Shipping 5 2013-10-01 2013-10-01 false Piping: Liquid pressure relief. 154.517 Section 154.517... and Process Piping Systems § 154.517 Piping: Liquid pressure relief. The cargo loading and discharge crossover headers, cargo hoses, and cargo loading arms must have means to relieve cargo pressure and to...

46 CFR 154.517 - Piping: Liquid pressure relief.

Code of Federal Regulations, 2012 CFR

2012-10-01

... 46 Shipping 5 2012-10-01 2012-10-01 false Piping: Liquid pressure relief. 154.517 Section 154.517... and Process Piping Systems § 154.517 Piping: Liquid pressure relief. The cargo loading and discharge crossover headers, cargo hoses, and cargo loading arms must have means to relieve cargo pressure and to...

46 CFR 154.517 - Piping: Liquid pressure relief.

Code of Federal Regulations, 2010 CFR

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Piping: Liquid pressure relief. 154.517 Section 154.517... and Process Piping Systems § 154.517 Piping: Liquid pressure relief. The cargo loading and discharge crossover headers, cargo hoses, and cargo loading arms must have means to relieve cargo pressure and to...

46 CFR 154.517 - Piping: Liquid pressure relief.

Code of Federal Regulations, 2011 CFR

2011-10-01

... 46 Shipping 5 2011-10-01 2011-10-01 false Piping: Liquid pressure relief. 154.517 Section 154.517... and Process Piping Systems § 154.517 Piping: Liquid pressure relief. The cargo loading and discharge crossover headers, cargo hoses, and cargo loading arms must have means to relieve cargo pressure and to...

--No Title--

Science.gov Websites

;] { float: left; margin-right: 3px; margin-left: 0; } .control-group { margin-bottom: 10px; } legend + .control-group { margin-top: 20px; -webkit-margin-top-collapse: separate; } .form-horizontal .control-group : 1px solid #999; page-break-inside: avoid; } thead { display: table-header-group; } tr, img { page

29 CFR 1915.55 - Gas welding and cutting.

Code of Federal Regulations, 2011 CFR

2011-07-01

... before cylinders are moved. (7) A suitable cylinder truck, chain, or other steadying device shall be used... ends of the supply hose that lead to the manifold, shall be such that the hose cannot be interchanged between fuel gas and oxygen manifolds and supply header connections. Adapters shall not be used to permit...

APT Blanket System Loss-of-Coolant Accident (LOCA) Based on Initial Conceptual Design - Case 4: External Pressurizer Surge Line Break Near Inlet Header

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hamm, L.L.

1998-10-07

This report is one of a series of reports documenting accident scenario simulations for the Accelerator Production of Tritium (APT) blanket heat removal systems. The simulations were performed in support of the Preliminary Safety Analysis Report (PSAR) for the APT.

46 CFR 151.50-84 - Sulfur dioxide.

Code of Federal Regulations, 2010 CFR

2010-10-01

... piping or manifold that carriers cargo liquid, except vapor lines connected to a common header, and (11... must be removed and cargo transfer piping must be disconnected at the cargo tanks. After the cargo piping is disconnected, both ends of the line must be plugged or fitted with blind flanges. [CGD 80-001...

CALUTRON PLANT ARRANGEMENT

DOEpatents

Waite, L.O.

1959-06-01

A description is given of an arrangement for calutrons in which the tanks and magnets are placed alternately in a race track'' figure. Pump connections are through the floor to the pumps below where roughing and finishing headers are provided. The arrangement provides more efficient and exonomical operaton, economy of construction, and saving of space. (T.R.H.)

77 FR 789 - Tres Palacios Gas Storage LLC; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2012-01-06

... Gas Storage LLC; Notice of Application Take notice that on December 20, 2011, Tres Palacios Gas Storage LLC (Tres Palacios), Two Brush Creek Boulevard, Kansas City, Missouri 64112, filed in the above... on its storage facility header pipeline system by: (i) Constructing a 19.7-mile, 24-inch diameter...

78 FR 14909 - Amendment of Class B Airspace Description; Houston, TX

Federal Register 2010, 2011, 2012, 2013, 2014

2013-03-08

... airport reference for describing the William P. Hobby Airport in the Class B airspace header from... established the William P. Hobby Airport, Airport Radar Service Area (ARSA) next to and under the existing... Intercontinental Airport and William P. Hobby Airport) in the Houston TCA description, and rescinded the William P...

Image Use Fees | Galaxy of Images

Science.gov Websites

This site has moved! Please go to our new Image Gallery site! dot header Image Use Fees Licensing , research and study purposes only. For current pricing, please download our Image Use Fee Schedule See our Frequently Asked Questions (FAQ) list for additional information. Purchase an image now Contact Information

Contacts | Galaxy of Images

Science.gov Websites

This site has moved! Please go to our new Image Gallery site! dot header Contact Us About the Image Galaxy For licensing and other usage questions, please contact: Image use and licensing ! Enter a search term and hit the search button to quickly find an image Go The above "Quick Search

Segy-change: The swiss army knife for the SEG-Y files

NASA Astrophysics Data System (ADS)

Stanghellini, Giuseppe; Carrara, Gabriela

Data collected during active and passive seismic surveys can be stored in many different, more or less standard, formats. One of the most popular is the SEG-Y format, developed since 1975 to store single-line seismic digital data on tapes, and now evolved to store them into hard-disk and other media as well. Unfortunately, sometimes, files that are claimed to be recorded in the SEG-Y format cannot be processed using available free or industrial packages. Aiming to solve this impasse we present segy-change, a pre-processing software program to view, analyze, change and fix errors present in SEG-Y data files. It is written in C language and it can be used also as a software library and is compatible with most operating systems. Segy-change allows the user to display and optionally change the values inside all parts of a SEG-Y file: the file header, the trace headers and the data blocks. In addition, it allows to do a quality check on the data by plotting the traces. We provide instructions and examples on how to use the software.

Study of the Cooldown and Warmup for the Eight Sectors of the Large Hadron Collider

NASA Astrophysics Data System (ADS)

Liu, L.; Riddone, G.; Tavian, L.

2004-06-01

The LHC cryogenic system is based on a five-point feed scheme with eight refrigerators serving the eight sectors of the LHC machine. The paper presents the simplified flow scheme of the eight sectors and the mathematical methods including the program flowchart and the boundary conditions to simulate the cooldown and warmup of these sectors. The methods take into account the effect of the pressure drop across the valves as well as the pressure evolution in the different headers of the cryogenic distribution line. The simulated pressure and temperature profiles of headers of the LHC sector during the cooldown and warmup are given and the temperature evolutions of entire processes of cooldown and warmup are presented. As a conclusion, the functions of the input temperature for the normal and fast cooldown and warmup, the cooldown and warmup time of each sector and the distributions of mass flow rates in each sector are summarized. The results indicate that it is possible to cool down any of the LHC sector within 12.7 days in normal operation and 6.8 days in case of fast operation.

Fabrication and installation of the Solar Two central receiver

DOE Office of Scientific and Technical Information (OSTI.GOV)

Litwin, R.Z.; Rogers, R.D.

The heart of the Solar Two power plant is the molten salt central receiver that has been designed, fabricated, and installed over an 18 month schedule. During this time, the receiver system from Solar One was also completely disassembled and removed. The receiver tower structure, for the most part, was left intact because Solar Two was designed to fit this structure such that construction time and costs could be minimized. In order to meet this aggressive schedule, receiver panel fabrication required the parallel production of many components. The sequence for assembly of the four major receiver panel components (i.e., tubes,more » header assembly, strongback, and header oven covers) and key fabrication activities such as welding are described. Once the receiver panels were complete, their installation at the site was begun, and the order in which receiver system components were installed in the tower is described. The completion of the Solar Two receiver proved the fabricability of this important system. However, successful operation of the system at Solar Two is needed to demonstrate the technical feasibility of the molten salt central receiver concept.« less

Determining approximate age of digital images using sensor defects

NASA Astrophysics Data System (ADS)

Fridrich, Jessica; Goljan, Miroslav

2011-02-01

The goal of temporal forensics is to establish temporal relationship among two or more pieces of evidence. In this paper, we focus on digital images and describe a method using which an analyst can estimate the acquisition time of an image given a set of other images from the same camera whose time ordering is known. This is achieved by first estimating the parameters of pixel defects, including their onsets, and then detecting their presence in the image under investigation. Both estimators are constructed using the maximum-likelihood principle. The accuracy and limitations of this approach are illustrated on experiments with three cameras. Forensic and law-enforcement analysts are expected to benefit from this technique in situations when the temporal data stored in the EXIF header is lost due to processing or editing images off-line or when the header cannot be trusted. Reliable methods for establishing temporal order between individual pieces of evidence can help reveal deception attempts of an adversary or a criminal. The causal relationship may also provide information about the whereabouts of the photographer.

An efficient incremental learning mechanism for tracking concept drift in spam filtering

PubMed Central

Sheu, Jyh-Jian; Chu, Ko-Tsung; Li, Nien-Feng; Lee, Cheng-Chi

2017-01-01

This research manages in-depth analysis on the knowledge about spams and expects to propose an efficient spam filtering method with the ability of adapting to the dynamic environment. We focus on the analysis of email’s header and apply decision tree data mining technique to look for the association rules about spams. Then, we propose an efficient systematic filtering method based on these association rules. Our systematic method has the following major advantages: (1) Checking only the header sections of emails, which is different from those spam filtering methods at present that have to analyze fully the email’s content. Meanwhile, the email filtering accuracy is expected to be enhanced. (2) Regarding the solution to the problem of concept drift, we propose a window-based technique to estimate for the condition of concept drift for each unknown email, which will help our filtering method in recognizing the occurrence of spam. (3) We propose an incremental learning mechanism for our filtering method to strengthen the ability of adapting to the dynamic environment. PMID:28182691

Scale-Free Compact Routing Schemes in Networks of Low Doubling Dimension

DOE Office of Scientific and Technical Information (OSTI.GOV)

Konjevod, Goran; Richa, Andréa W.; Xia, Donglin

In this work, we consider compact routing schemes in networks of low doubling dimension, where the doubling dimension is the least value α such that any ball in the network can be covered by at most 2 α balls of half radius. There are two variants of routing-scheme design: (i) labeled (name-dependent) routing, in which the designer is allowed to rename the nodes so that the names (labels) can contain additional routing information, for example, topological information; and (ii) name-independent routing, which works on top of the arbitrary original node names in the network, that is, the node names aremore » independent of the routing scheme. In this article, given any constant ε ϵ (0, 1) and an n-node edge-weighted network of doubling dimension α ϵ O(loglog n), we present —a (1 + ε)-stretch labeled compact routing scheme with Γlog n-bit routing labels, O(log 2 n/loglog n)-bit packet headers, and ((1/ε) O(α) log 3 n)-bit routing information at each node; —a (9 + ε)-stretch name-independent compact routing scheme with O(log 2 n/loglog n)-bit packet headers, and ((1/ε) O(α) log 3 n)-bit routing information at each node. In addition, we prove a lower bound: any name-independent routing scheme with o(n (ε/60)2) bits of storage at each node has stretch no less than 9 - ε for any ε ϵ (0, 8). Therefore, our name-independent routing scheme achieves asymptotically optimal stretch with polylogarithmic storage at each node and packet headers. Note that both schemes are scale-free in the sense that their space requirements do not depend on the normalized diameter Δ of the network. Finally, we also present a simpler nonscale-free (9 + ε)-stretch name-independent compact routing scheme with improved space requirements if Δ is polynomial in n.« less

Review on the Celestial Sphere Positioning of FITS Format Image Based on WCS and Research on General Visualization

NASA Astrophysics Data System (ADS)

Song, W. M.; Fan, D. W.; Su, L. Y.; Cui, C. Z.

2017-11-01

Calculating the coordinate parameters recorded in the form of key/value pairs in FITS (Flexible Image Transport System) header is the key to determine FITS images' position in the celestial system. As a result, it has great significance in researching the general process of calculating the coordinate parameters. By combining CCD related parameters of astronomical telescope (such as field, focal length, and celestial coordinates in optical axis, etc.), astronomical images recognition algorithm, and WCS (World Coordinate System) theory, the parameters can be calculated effectively. CCD parameters determine the scope of star catalogue, so that they can be used to build a reference star catalogue by the corresponding celestial region of astronomical images; Star pattern recognition completes the matching between the astronomical image and reference star catalogue, and obtains a table with a certain number of stars between CCD plane coordinates and their celestial coordinates for comparison; According to different projection of the sphere to the plane, WCS can build different transfer functions between these two coordinates, and the astronomical position of image pixels can be determined by the table's data we have worked before. FITS images are used to carry out scientific data transmission and analyze as a kind of mainstream data format, but only to be viewed, edited, and analyzed in the professional astronomy software. It decides the limitation of popular science education in astronomy. The realization of a general image visualization method is significant. FITS is converted to PNG or JPEG images firstly. The coordinate parameters in the FITS header are converted to metadata in the form of AVM (Astronomy Visualization Metadata), and then the metadata is added to the PNG or JPEG header. This method can meet amateur astronomers' general needs of viewing and analyzing astronomical images in the non-astronomical software platform. The overall design flow is realized through the java program and tested by SExtractor, WorldWide Telescope, picture viewer, and other software.

Scale-Free Compact Routing Schemes in Networks of Low Doubling Dimension

DOE PAGES

Konjevod, Goran; Richa, Andréa W.; Xia, Donglin

2016-06-15

In this work, we consider compact routing schemes in networks of low doubling dimension, where the doubling dimension is the least value α such that any ball in the network can be covered by at most 2 α balls of half radius. There are two variants of routing-scheme design: (i) labeled (name-dependent) routing, in which the designer is allowed to rename the nodes so that the names (labels) can contain additional routing information, for example, topological information; and (ii) name-independent routing, which works on top of the arbitrary original node names in the network, that is, the node names aremore » independent of the routing scheme. In this article, given any constant ε ϵ (0, 1) and an n-node edge-weighted network of doubling dimension α ϵ O(loglog n), we present —a (1 + ε)-stretch labeled compact routing scheme with Γlog n-bit routing labels, O(log 2 n/loglog n)-bit packet headers, and ((1/ε) O(α) log 3 n)-bit routing information at each node; —a (9 + ε)-stretch name-independent compact routing scheme with O(log 2 n/loglog n)-bit packet headers, and ((1/ε) O(α) log 3 n)-bit routing information at each node. In addition, we prove a lower bound: any name-independent routing scheme with o(n (ε/60)2) bits of storage at each node has stretch no less than 9 - ε for any ε ϵ (0, 8). Therefore, our name-independent routing scheme achieves asymptotically optimal stretch with polylogarithmic storage at each node and packet headers. Note that both schemes are scale-free in the sense that their space requirements do not depend on the normalized diameter Δ of the network. Finally, we also present a simpler nonscale-free (9 + ε)-stretch name-independent compact routing scheme with improved space requirements if Δ is polynomial in n.« less

75 FR 50758 - Leader One Energy, LLC; Supplemental Notice of Intent To Prepare an Environmental Assessment for...

Federal Register 2010, 2011, 2012, 2013, 2014

2010-08-17

...-diameter pipeline, the Leader One Header Pipeline, to connect the storage facility to Colorado Interstate... (202) 502-8371. For instructions on connecting to eLibrary, refer to the last page of this notice. Land... historic district, site, building, structure, or object included in or eligible for inclusion in the...

FGGE/ERBZ tape specification and shipping letter description

NASA Technical Reports Server (NTRS)

Han, D.; Lo, H.

1983-01-01

The FGGE/ERBZ tape contains 5 parameters which are extracted and reformatted from the Nimbus-7 ERB Zonal Means Tape. There are three types of files on a FGGE/ERBZ tape: a tape header file, and data files. Physical characteristics, gross format, and file specifications are given. A sample tape check/document printout (shipping letter) is included.

9 CFR 381.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2014 CFR

2014-01-01

... plates. Whenever one or more divider plates are used between any two layers of containers or placed on... from several still retorts shall lead to the atmosphere. The manifold header shall not be controlled by...) Venting through multiple 1 inch (2.5 cm) vents discharging directly to the atmosphere. EC11SE91.047...

9 CFR 381.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2012 CFR

2012-01-01

... plates. Whenever one or more divider plates are used between any two layers of containers or placed on... from several still retorts shall lead to the atmosphere. The manifold header shall not be controlled by...) Venting through multiple 1 inch (2.5 cm) vents discharging directly to the atmosphere. EC11SE91.047...

9 CFR 381.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2013 CFR

2013-01-01

... plates. Whenever one or more divider plates are used between any two layers of containers or placed on... from several still retorts shall lead to the atmosphere. The manifold header shall not be controlled by...) Venting through multiple 1 inch (2.5 cm) vents discharging directly to the atmosphere. EC11SE91.047...

Asserting National Sovereignty in Cyberspace: The Case for Internet Border Inspection

DTIC Science & Technology

2003-06-01

Influencing Foreign Policy. in Internet and International Systems: Information Technology and American Foreign Policy Decisionmaking Workshop. 1999...investigative Agencies that investigate violations of federal law IO Information Operations, military operations in information realm IP Internet ...Protocol, a specific format for Internet packet headers IW Information Warfare, part of information operations NCP Network Control Protocol NSA

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2012 CFR

2012-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2011 CFR

2011-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2013 CFR

2013-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR Table 2 to Subpart IIIii of... - Work Practice Standards-Required Inspections

Code of Federal Regulations, 2014 CFR

2014-07-01

... hydrogen cooler, and all other vessels, piping, and equipment in liquid mercury service in the cell room... subpart. 12. Each decomposer and all hydrogen piping up to the hydrogen header Half day Equipment that is leaking hydrogen and/or mercury vapor Take the required action specified in Table 3 to this subpart. 13...

40 CFR 60.756 - Monitoring of operations.

Code of Federal Regulations, 2010 CFR

2010-07-01

... owner or operator seeking to comply with § 60.752(b)(2)(ii)(A) for an active gas collection system shall... temperature measurements at each wellhead and: (1) Measure the gauge pressure in the gas collection header on... the landfill gas on a monthly basis as provided in § 60.755(a)(5); and (3) Monitor temperature of the...

40 CFR 60.756 - Monitoring of operations.

Code of Federal Regulations, 2011 CFR

2011-07-01

... owner or operator seeking to comply with § 60.752(b)(2)(ii)(A) for an active gas collection system shall... temperature measurements at each wellhead and: (1) Measure the gauge pressure in the gas collection header on... the landfill gas on a monthly basis as provided in § 60.755(a)(5); and (3) Monitor temperature of the...

XHTML Vocabulary

Science.gov Websites

content of resource. contentinfo contains meta information about the content on the page or the page as a Applications Vocabulary alert A message with important, and usually time-sensitive, information. Also see : true, false, or mixed. columnheader A cell containing header information for a column. combobox A

6. NORTH WALL OF BACKBUILDING AND DETAIL OF BRICKWORK. NOTE ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

6. NORTH WALL OF BACKBUILDING AND DETAIL OF BRICKWORK. NOTE GLAZED (BLACK) HEADER COURSES LAID GENERALLY ONE IN SIX COURSES (COMMON BOND), ALTHOUGH SLIGHT VARIATION IS VISIBLE; STRETCHERS ARE RED, PRODUCING A STRIPED WALL. NOTE ALSO THE LOOSE BONDING OF BRICK - Samuel Neave House & Store, 272-274 South Second Street, Philadelphia, Philadelphia County, PA

40 CFR Appendix II to Subpart S of... - As-Received Testing Vehicle Rejection Criteria

Code of Federal Regulations, 2010 CFR

2010-07-01

... manufacturer may request a vehicle be rejected because of the addition of an aftermarket security system if the... inoperative, has been replaced, or the indicated mileage is outside the target range. 2. The emission system... transmission, a modified exhaust system, (headers, side pipes, aftermarket catalysts, etc) or an exhaust system...

Non-tracking solar concentrator with a high concentration ratio

DOEpatents

Hinterberger, Henry

1977-01-01

A nontracking solar concentrator with a high concentration ratio is provided. The concentrator includes a plurality of energy absorbers which communicate with a main header by which absorbed heat is removed. Undesired heat flow of those absorbers not being heated by radiant energy at a particular instant is impeded, improving the efficiency of the concentrator.

15 CFR 738.3 - Commerce Country Chart structure.

Code of Federal Regulations, 2014 CFR

2014-01-01

... for Control listed in the Export Control Classification Number (ECCN) that applies to the item. Some... may impose license requirements on the items described in that ECCN. (1) ECCNs 0A983, 5A001.f.1, 5A980... listed in the “Country Chart” header within the “License Requirements” section of each ECCN. (d) Cells...

Influence of harvester and weather conditions on field loss and milling quality of rough rice

USDA-ARS?s Scientific Manuscript database

A better understanding of factors affecting field losses and milling quality during harvest is needed to improve the economic value of rice. The main objective of this study was to evaluate the impact of harvester header, harvester type, and weather conditions on field loss and milling quality of ro...

10 CFR 2.1013 - Use of the electronic docket during the proceeding.

Code of Federal Regulations, 2012 CFR

2012-01-01

... searchable full text, by header and image, as appropriate. (b) Absent good cause, all exhibits tendered... circumstances where submitters may need to use an image scanned before January 1, 2004, in a document created after January 1, 2004, or the scanning process for a large, one-page image may not successfully complete...

10 CFR 2.1013 - Use of the electronic docket during the proceeding.

Code of Federal Regulations, 2013 CFR

2013-01-01

... header and image, as appropriate. (b) Absent good cause, all exhibits tendered during the hearing must... may need to use an image scanned before January 1, 2004, in a document created after January 1, 2004, or the scanning process for a large, one-page image may not successfully complete at the 300 dpi...

The Phelix Pulsed Power Project: Bringing Portable Magnetic Drive to World Class Radiography

DTIC Science & Technology

2011-06-01

vitreous carbon damping resistors are used on the output headers of each module for a total of 25.1 mΩ of resistance. Figure 6. The PHELIX portable...4 MA peak current in the secondary winding for driving a liner. In order to not produce too much reverse voltage on the capacitors, reticulated

About Galaxy of Images

Science.gov Websites

This site has moved! Please go to our new Image Gallery site! dot header About the Image Galaxy are added regularly. Statistics about the Galaxy of Images Frequently Asked Questions Image Use Fees Quick Search! Enter a search term and hit the search button to quickly find an image Go The above "

9 CFR 318.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2013 CFR

2013-01-01

... review. (b) Divider plates. Whenever one or more divider plates are used between any two layers of... atmosphere. The manifold header shall not be controlled by a valve and shall be of a size such that the cross... discharging directly to the atmosphere. EC11SE91.017 Specifications (Figure 1): One, 1-inch (2.5 cm) vent for...

9 CFR 318.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2012 CFR

2012-01-01

... review. (b) Divider plates. Whenever one or more divider plates are used between any two layers of... atmosphere. The manifold header shall not be controlled by a valve and shall be of a size such that the cross... discharging directly to the atmosphere. EC11SE91.017 Specifications (Figure 1): One, 1-inch (2.5 cm) vent for...

9 CFR 318.305 - Equipment and procedures for heat processing systems.

Code of Federal Regulations, 2014 CFR

2014-01-01

... review. (b) Divider plates. Whenever one or more divider plates are used between any two layers of... atmosphere. The manifold header shall not be controlled by a valve and shall be of a size such that the cross... discharging directly to the atmosphere. EC11SE91.017 Specifications (Figure 1): One, 1-inch (2.5 cm) vent for...

The Alaska Arctic Vegetation Archive (AVA-AK)

Treesearch

Donald A. Walker; Amy L. Breen; Lisa A. Druckenmiller; Lisa W. Wirth; Will Fisher; Martha K. Raynolds; Jozef Šibík; Marilyn D. Walker; Stephan Hennekens; Keith Boggs; Tina Boucher; Marcel Buchhorn; Helga Bültmann; David J. Cooper; Fred J.A Daniëls; Scott J. Davidson; James J. Ebersole; Sara C. Elmendorf; Howard E. Epstein; William A. Gould; Robert D. Hollister; Colleen M. Iversen; M. Torre Jorgenson; Anja Kade; Michael T. Lee; William H. MacKenzie; Robert K. Peet; Jana L. Peirce; Udo Schickhoff; Victoria L. Sloan; Stephen S. Talbot; Craig E. Tweedie; Sandra Villarreal; Patrick J. Webber; Donatella Zona

2016-01-01

The Alaska Arctic Vegetation Archive (AVA-AK, GIVD-ID: NA-US-014) is a free, publically available database archive of vegetation-plot data from the Arctic tundra region of northern Alaska. The archive currently contains 24 datasets with 3,026 non-overlapping plots. Of these, 74% have geolocation data with 25-m or better precision. Species cover data and header data are...

Story Sparks! How to Kindle Your Young Writers' Imaginations

ERIC Educational Resources Information Center

Traver, Warren

2004-01-01

Make writing less of a task and more of an adventure through this creative and imaginative collection of writing prompts, targeted at grade levels 2 to 5. It provides not only ideas and inspiration, but also motivation. This book includes: (1) Story Headers: single pictures with story titles that kids write about; (2) Every Picture Tells a Story:…

Intermittent output failure of a VVI device due to the disintegration of the generator.

PubMed

Böhm, A; Kayser, S; Pintér, A; Préda, I

2001-01-01

The metal case and the header of a Biovallees Coralite 247 pacemaker fell apart in a patient resulting in syncope due to myopotential inhibition. Upon recalling our patients with that type of device, we found a similar technological failure in 11 of 16 of them. This finding warrants a consideration for recalling that Biovallees device.

Triple Header Annual Workshop Proceedings (12th, Sarasota, Florida, April 25-29, 1993).

ERIC Educational Resources Information Center

American Probation and Parole Association, Lexington, KY.

The family and juvenile court system in the United States is overwhelmed with the number of court cases involving the incarceration of young people. The proceedings of this conference, the goal of which was to find alternatives to incarceration and improve efficiency of the juvenile court system, are summaries of the following 22 presentations:…

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2014 CFR

2014-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2013 CFR

2013-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2012 CFR

2012-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

16 CFR Appendix A to Part 306 - Summary of Labeling Requirements for Biodiesel Fuels

Code of Federal Regulations, 2011 CFR

2011-01-01

... Biodiesel Fuels A Appendix A to Part 306 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER... Part 306—Summary of Labeling Requirements for Biodiesel Fuels (Part 1 of 2) Fuel type Blends of 5 percent or less Blends of more than 5 but not more than 20 percent Header Text Color Biodiesel No label...

40 CFR Appendix G to Part 75 - Determination of CO2 Emissions

Code of Federal Regulations, 2014 CFR

2014-07-01

... following procedures to estimate daily CO2 mass emissions from the combustion of fossil fuels. The optional... tons/day) from the combustion of fossil fuels. Where fuel flow is measured in a common pipe header (i.e... discharged to the atmosphere (in tons/day) as the sum of CO2 emissions from combustion and, if applicable...

40 CFR Appendix G to Part 75 - Determination of CO2 Emissions

Code of Federal Regulations, 2011 CFR

2011-07-01

... following procedures to estimate daily CO2 mass emissions from the combustion of fossil fuels. The optional... tons/day) from the combustion of fossil fuels. Where fuel flow is measured in a common pipe header (i.e... discharged to the atmosphere (in tons/day) as the sum of CO2 emissions from combustion and, if applicable...

40 CFR Appendix G to Part 75 - Determination of CO2 Emissions

Code of Federal Regulations, 2013 CFR

2013-07-01

... following procedures to estimate daily CO2 mass emissions from the combustion of fossil fuels. The optional... tons/day) from the combustion of fossil fuels. Where fuel flow is measured in a common pipe header (i.e... discharged to the atmosphere (in tons/day) as the sum of CO2 emissions from combustion and, if applicable...

40 CFR Appendix G to Part 75 - Determination of CO2 Emissions

Code of Federal Regulations, 2012 CFR

2012-07-01

... following procedures to estimate daily CO2 mass emissions from the combustion of fossil fuels. The optional... tons/day) from the combustion of fossil fuels. Where fuel flow is measured in a common pipe header (i.e... discharged to the atmosphere (in tons/day) as the sum of CO2 emissions from combustion and, if applicable...

My Objections to Outcome [Note the Singular] Assessment

ERIC Educational Resources Information Center

Digby, Joan

2014-01-01

Rubric means red ochre--red earth--as in Bryce Canyon and Sedona. Red headers were used in medieval manuscripts as section or chapter markers, and you can bet that the Whore of Babylon got herself some fancy rubrics over the years. Through most of its history, the word has been attached to religious texts and liturgy; rubrics were used as…

Performance Analysis of AeroRP with Ground Station Advertisements

DTIC Science & Technology

2012-03-12

results showed that AeroRP outperforms the traditional MANET routing protocols in terms of throughput and packet delivery ra - tio (PDR) [5, 6]. AeroRP...and waiting for the source to re- send the packet increases the end-to-end delay. The AeroNP corruption indicator and HEC -CRC (header error check...Dev ID | NP HEC CRC-16 | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ \\ \\ / AeroTP Payload

--No Title--

Science.gov Websites

solid #666}.content-list-widget .header-box .title{color:#fff;font-size:1.35em;margin-bottom:0;padding -color:#0079C2;border-bottom:5px solid #00A4E4}.content-list-widget{line-height:1.7}ul.fa-blue-arrow ;background-color:rgba(0,0,0,.8);box-sizing:border-box;color:#fff;font-family:Roboto,'Helvetica Neue

--No Title--

Science.gov Websites

Calendar * @subpackage Default Theme */ a:hover {text-decoration:none;color:#FF6600;} a:active {text -decoration:underline;color:#FF6600;} a.series {float:right;} a.output {display:block;width:80%;} p{margin:0 0 10px 0 header {display:block;font-size:13px;font-weight:bold;border-bottom:1px solid #3D3F3E;color:#000000

Standardizing Documentation of FITS Headers

NASA Astrophysics Data System (ADS)

Hourcle, Joseph

2014-06-01

Although the FITS file format[1] can be self-documenting, human intervention is often needed to read the headers to write the necessary transformations to make a given instrument team's data compatible with our preferred analysis package. External documentation may be needed to determine what the values are of coded values or unfamiliar acronyms.Different communities have interpreted keywords slightly differently. This has resulted in ambiguous fields such as DATE-OBS, which could be either the start or mid-point of an observation.[2]Conventions for placing units and additional information within the comments of a FITS card exist, but they require re-writing the FITS file. This operation can be quite costly for large archives, and should not be taken lightly when dealing with issues of digital preservation.We present what we believe is needed for a machine-actionable external file describing a given collection of FITS files. We seek comments from data producers, archives, and those writing software to help develop a single, useful, implementable standard.References:[1] Pence, et.al. 2010, http://dx.doi.org/10.1051/0004-6361/201015362[2] Rots, et.al, (in preparation), http://hea-www.cfa.harvard.edu arots/TimeWCS/

TOLNet Data Format for Lidar Ozone Profile & Surface Observations

NASA Astrophysics Data System (ADS)

Chen, G.; Aknan, A. A.; Newchurch, M.; Leblanc, T.

2015-12-01

The Tropospheric Ozone Lidar Network (TOLNet) is an interagency initiative started by NASA, NOAA, and EPA in 2011. TOLNet currently has six Lidars and one ozonesonde station. TOLNet provides high-resolution spatio-temporal measurements of tropospheric (surface to tropopause) ozone and aerosol vertical profiles to address fundamental air-quality science questions. The TOLNet data format was developed by TOLNet members as a community standard for reporting ozone profile observations. The development of this new format was primarily based on the existing NDAAC (Network for the Detection of Atmospheric Composition Change) format and ICARTT (International Consortium for Atmospheric Research on Transport and Transformation) format. The main goal is to present the Lidar observations in self-describing and easy-to-use data files. The TOLNet format is an ASCII format containing a general file header, individual profile headers, and the profile data. The last two components repeat for all profiles recorded in the file. The TOLNet format is both human and machine readable as it adopts standard metadata entries and fixed variable names. In addition, software has been developed to check for format compliance. To be presented is a detailed description of the TOLNet format protocol and scanning software.

Retrofitting coils

DOE Office of Scientific and Technical Information (OSTI.GOV)

Merrill, D.G.

1995-12-01

This article provides guidelines for maintaining efficiency by determining which coils require replacement and the selection of replacement coils to match the originals in terms of size, performance, materials, and material thickness. Coils in the Rio Hondo College have been in use 24 years. The author recently found an installation where the coils installed 20 years ago look like new, which is the result of a highly effective preventive maintenance program. But these exceptions are countered by some installations lasting considerably less time. Periodic coil inspections are the best way to find leaks and deterioration. Leaking coils have an unhappymore » way of announcing their presence through unwanted water on ceilings, walls, and machine room floors. Minuscule streams of water impinge on nonwater-tight housings or are picked up in the air stream to leak out of the ductwork. Coil return bends and headers seem to have the greater incidence of failure and should be checked first for pinhole or joint leaks. Also, check along the points where the tubes penetrate the tube sheets. The coil headers should be checked as should the tubes along the front and backside of the coil. The more rows the coil has, the more difficult this latter assignment becomes.« less

[Central online quality assurance in radiology: an IT solution exemplified by the German Breast Cancer Screening Program].

PubMed

Czwoydzinski, J; Girnus, R; Sommer, A; Heindel, W; Lenzen, H

2011-09-01

Physical-technical quality assurance is one of the essential tasks of the National Reference Centers in the German Breast Cancer Screening Program. For this purpose the mammography units are required to transfer the measured values of the constancy tests on a daily basis and all phantom images created for this purpose on a weekly basis to the reference centers. This is a serious logistical challenge. To meet these requirements, we developed an innovative software tool. By the end of 2005, we had already developed web-based software (MammoControl) allowing the transmission of constancy test results via entry forms. For automatic analysis and transmission of the phantom images, we then introduced an extension (MammoControl DIANA). This was based on Java, Java Web Start, the NetBeans Rich Client Platform, the Pixelmed Java DICOM Toolkit and the ImageJ library. MammoControl DIANA was designed to run locally in the mammography units. This allows automated on-site image analysis. Both results and compressed images can then be transmitted to the reference center. We developed analysis modules for the daily and monthly consistency tests and additionally for a homogeneity test. The software we developed facilitates the immediate availability of measurement results, phantom images, and DICOM header data in all reference centers. This allows both targeted guidance and short response time in the case of errors. We achieved a consistent IT-based evaluation with standardized tools for the entire screening program in Germany. © Georg Thieme Verlag KG Stuttgart · New York.

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2010 CFR

2010-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2014 CFR

2014-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2011 CFR

2011-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2013 CFR

2013-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

14 CFR 291.45 - BTS Schedule T-100, U.S. Air Carrier Traffic and Capacity Data by Nonstop Segment and On-Flight...

Code of Federal Regulations, 2012 CFR

2012-01-01

...) must report joint services. (c) Service classes. (1) The statistical classifications are designed to... methodology. Refer to paragraph (i) of this appendix for microcomputer record layouts. (iii) Microcomputer... identifier field of the header labels should be “T-100.SYSTEM”. (h) Magnetic tape record layouts for T-100—(1...

Magnetized Target Fusion - Field Reversed Configuration Formation and Injection (MTF-FRC)

DTIC Science & Technology

2009-11-06

from accidental breakage and personnel from injury in that event. The pumps for the vacuum system included a Varian dry scroll pump that was...a dry scroll (oil-free) mechanical pump could be used, as mTorr pressures would be sufficient for the vacuum switch voltage hold-off and operation...56 FIGURE 46. ROUGHING PUMP AND VACUUM -GAUGE CONTROLLERS BENEATH THETA COIL CABLE HEADER

Techniques for the Detection of Faulty Packet Header Modifications

DTIC Science & Technology

2014-03-12

layer approaches to check if packets are being altered by middleboxes and were primarily developed as network neutrality analysis tools. Switzerland works...local and metropolitan area networks –specific requirements part 11: Wireless LAN medium access control (MAC) and physical layer (PHY) specifications...policy or position of the Department of Defense or the U.S. Government. Understanding, measuring, and debugging IP networks , particularly across

Design and Evaluation for the End-to-End Detection of TCP/IP Header Manipulation

DTIC Science & Technology

2014-06-01

Cooperative Association for Internet Data Analysis CDN content delivery network CE congestion encountered CRC cyclic redundancy check CWR congestion...Switzerland was primarily developed as a network neutrality analysis tool to detect when internet service providers (ISPs) were interfering with...maximum 200 words) Understanding, measuring, and debugging IP networks , particularly across administrative domains, is challenging. One aspect of the

--No Title--

Science.gov Websites

mobile_icon{margin-right:5px;margin-left:8px}div#tools-main span i{margin-right:6px;float:left}div #tools-main i.icon-eere-arrow-header-link{margin:0 0 0 4px;vertical-align:center}div#tools-main div.highlight-box{margin-top:20px}div#tools-main div.highlight-box div{height:70px;width:33px;display:inline

VizieR Online Data Catalog: Catalogue of Radio Stars (Wendker, 2001)

NASA Astrophysics Data System (ADS)

Wendker, H. J.

2015-06-01

The first version of this catalogue was published in Abh.Hamburger Sternw. 1978, Vol.10, p 1ff. (CDS Catalogue II/129). A second version was published in 1987 (1987A&AS...69...87W) and microfiches (CDS Catalogue II/147). A third version was published 1995A&AS..109..177W (CDS Catalogue II/199). The basic concept of the earlier versions is preserved (in file "catalog.txt"), namely one entry per star per frequency per paper. Space is now provided, however, to add more informations. These may be of technical or astronomical nature. Usually month and year of observation and the number of independent data points or length of monitoring session are given. In the file "catalog.txt", all radio data are preceded by a header which contains information on the star or stellar system. (Note, that a physical stellar system is regarded as one single entry and that comments pertaining to individual components are found directly behind the observational data). Stellar data like names, position, proper motion, magnitudes and spectroscopic types are given in fixed format in a self-explanatory fashion. It is tried to have typical values from commonly available references. It is not intended to compete here with other compilations. These header informations are collected when the star is entered for the first time. They are only changed when new values are available while additional radio references are added. An arbitrarily expandable section for unformatted text finishes the header. Finally, the units of the radio data remain in MHz (column#1) and mJy (columns #2. and #3). All coordinates refer to epoch and equinox 1950.0 (e.g. B1950). This is a so-called merged version e.g. all stars, those detected at least once and those with upper limits only, are listed in order of ascending right ascension. The detected stars are marked with a "D" in the outermost right hand column in lines 1 to 5 ('D' in column "Det" of the file "stars.dat"). The last updating occurred on 2001-Mar-06. In this version stars have new running numbers. (4 data files).

The Next Generation of HLA Image Products

NASA Astrophysics Data System (ADS)

Gaffney, N. I.; Casertano, S.; Ferguson, B.

2012-09-01

We present the re-engineered pipeline based on existing and improved algorithms with the aim of improving processing quality, cross-instrument portability, data flow management, and software maintenance. The Hubble Legacy Archive (HLA) is a project to add value to the Hubble Space Telescope data archive by producing and delivering science-ready drizzled data products and source lists derived from these products. Initially, ACS, NICMOS, and WFCP2 data were combined using instrument-specific pipelines based on scripts developed to process the ACS GOODS data and a separate set of scripts to generate source extractor and DAOPhot source lists. The new pipeline, initially designed for WFC3 data, isolates instrument-specific processing and is easily extendable to other instruments and to generating wide-area mosaics. Significant improvements have been made in image combination using improved alignment, source detection, and background equalization routines. It integrates improved alignment procedures, better noise model, and source list generation within a single code base. Wherever practical, PyRAF based routines have been replaced with non-IRAF based python libraries (e.g. NumPy and PyFITS). The data formats have been modified to handle better and more consistent propagation of information from individual exposures to the combined products. A new exposure layer stores the effective exposure time for each pixel in the sky which is key in properly interpreting combined images from diverse data that were not initially planned to be mosaiced. We worked to improve the validity of the metadata within our FITS headers for these products relative to standard IRAF/PyRAF processing. Any keywords that pertain to individual exposures have been removed from the primary and extension headers and placed in a table extension for more direct and efficient perusal. This mechanism also allows for more detailed information on the processing of individual images to be stored and propagated providing a more hierarchical metadata storage system than key value pair FITS headers provide. In this poster we will discuss the changes to the pipeline processing and source list generation and the lessons learned which may be applicable to other archive projects as well as discuss our new metadata curation and preservation process.

Estimating pediatric entrance skin dose from digital radiography examination using DICOM metadata: A quality assurance tool.

PubMed

Brady, S L; Kaufman, R A

2015-05-01

To develop an automated methodology to estimate patient examination dose in digital radiography (DR) imaging using DICOM metadata as a quality assurance (QA) tool. Patient examination and demographical information were gathered from metadata analysis of DICOM header data. The x-ray system radiation output (i.e., air KERMA) was characterized for all filter combinations used for patient examinations. Average patient thicknesses were measured for head, chest, abdomen, knees, and hands using volumetric images from CT. Backscatter factors (BSFs) were calculated from examination kVp. Patient entrance skin air KERMA (ESAK) was calculated by (1) looking up examination technique factors taken from DICOM header metadata (i.e., kVp and mA s) to derive an air KERMA (k air) value based on an x-ray characteristic radiation output curve; (2) scaling k air with a BSF value; and (3) correcting k air for patient thickness. Finally, patient entrance skin dose (ESD) was calculated by multiplying a mass-energy attenuation coefficient ratio by ESAK. Patient ESD calculations were computed for common DR examinations at our institution: dual view chest, anteroposterior (AP) abdomen, lateral (LAT) skull, dual view knee, and bone age (left hand only) examinations. ESD was calculated for a total of 3794 patients; mean age was 11 ± 8 yr (range: 2 months to 55 yr). The mean ESD range was 0.19-0.42 mGy for dual view chest, 0.28-1.2 mGy for AP abdomen, 0.18-0.65 mGy for LAT view skull, 0.15-0.63 mGy for dual view knee, and 0.10-0.12 mGy for bone age (left hand) examinations. A methodology combining DICOM header metadata and basic x-ray tube characterization curves was demonstrated. In a regulatory era where patient dose reporting has become increasingly in demand, this methodology will allow a knowledgeable user the means to establish an automatable dose reporting program for DR and perform patient dose related QA testing for digital x-ray imaging.

Estimating pediatric entrance skin dose from digital radiography examination using DICOM metadata: A quality assurance tool

DOE Office of Scientific and Technical Information (OSTI.GOV)

Brady, S. L., E-mail: samuel.brady@stjude.org; Kaufman, R. A., E-mail: robert.kaufman@stjude.org

Purpose: To develop an automated methodology to estimate patient examination dose in digital radiography (DR) imaging using DICOM metadata as a quality assurance (QA) tool. Methods: Patient examination and demographical information were gathered from metadata analysis of DICOM header data. The x-ray system radiation output (i.e., air KERMA) was characterized for all filter combinations used for patient examinations. Average patient thicknesses were measured for head, chest, abdomen, knees, and hands using volumetric images from CT. Backscatter factors (BSFs) were calculated from examination kVp. Patient entrance skin air KERMA (ESAK) was calculated by (1) looking up examination technique factors taken frommore » DICOM header metadata (i.e., kVp and mA s) to derive an air KERMA (k{sub air}) value based on an x-ray characteristic radiation output curve; (2) scaling k{sub air} with a BSF value; and (3) correcting k{sub air} for patient thickness. Finally, patient entrance skin dose (ESD) was calculated by multiplying a mass–energy attenuation coefficient ratio by ESAK. Patient ESD calculations were computed for common DR examinations at our institution: dual view chest, anteroposterior (AP) abdomen, lateral (LAT) skull, dual view knee, and bone age (left hand only) examinations. Results: ESD was calculated for a total of 3794 patients; mean age was 11 ± 8 yr (range: 2 months to 55 yr). The mean ESD range was 0.19–0.42 mGy for dual view chest, 0.28–1.2 mGy for AP abdomen, 0.18–0.65 mGy for LAT view skull, 0.15–0.63 mGy for dual view knee, and 0.10–0.12 mGy for bone age (left hand) examinations. Conclusions: A methodology combining DICOM header metadata and basic x-ray tube characterization curves was demonstrated. In a regulatory era where patient dose reporting has become increasingly in demand, this methodology will allow a knowledgeable user the means to establish an automatable dose reporting program for DR and perform patient dose related QA testing for digital x-ray imaging.« less

Simulation of heat and mass transfer processes in the experimental section of the air-condensing unit of Scientific Production Company "Turbocon"

NASA Astrophysics Data System (ADS)

Artemov, V. I.; Minko, K. B.; Yan'kov, G. G.; Kiryukhin, A. V.

2016-05-01

A mathematical model was developed to be used for numerical analysis of heat and mass transfer processes in the experimental section of the air condenser (ESAC) created in the Scientific Production Company (SPC) "Turbocon" and mounted on the territory of the All-Russia Thermal Engineering Institute. The simulations were performed using the author's CFD code ANES. The verification of the models was carried out involving the experimental data obtained in the tests of ESAC. The operational capability of the proposed models to calculate the processes in steam-air mixture and cooling air and algorithms to take into account the maldistribution in the various rows of tube bundle was shown. Data on the influence of temperature and flow rate of the cooling air on the pressure in the upper header of ESAC, effective heat transfer coefficient, steam flow distribution by tube rows, and the dimensions of the ineffectively operating zones of tube bundle for two schemes of steam-air mixture flow (one-pass and two-pass ones) were presented. It was shown that the pressure behind the turbine (in the upper header) increases significantly at increase of the steam flow rate and reduction of the flow rate of cooling air and its temperature rise, and the maximum value of heat transfer coefficient is fully determined by the flow rate of cooling air. Furthermore, the steam flow rate corresponding to the maximum value of heat transfer coefficient substantially depends on the ambient temperature. The analysis of the effectiveness of the considered schemes of internal coolant flow was carried out, which showed that the two-pass scheme is more effective because it provides lower pressure in the upper header, despite the fact that its hydraulic resistance at fixed flow rate of steam-air mixture is considerably higher than at using the one-pass schema. This result is a consequence of the fact that, in the two-pass scheme, the condensation process involves the larger internal surface of tubes, results in lower values of Δ t (the temperature difference between internal and external coolant) for a given heat load.

Examination of a Capabilities-based Prioritization Scheme for Service-Oriented Architecture Afloat

DTIC Science & Technology

2012-09-01

Oriented Architecture Afloat 5. FUNDING NUMBERS 6. AUTHOR(S) Matthew C. Horton 7. PERFORMING ORGANIZATION NAME(S) AND ADDRESS (ES) Naval...Postgraduate School Monterey, CA 93943–5000 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING /MONITORING AGENCY NAME(S) AND ADDRESS (ES) N/A...within the Internet Protocol Version 4 ( IPv4 ) header (Xiao & Ni, 1999). By manipulating three bits within this byte, applications may specify

Iraqi Army Facilities Under the Iraq Security Forces Fund, Diyanah and Debecha, Iraq

DTIC Science & Technology

2008-01-17

reinforcement bars and cast each building’s roof flatwork and horizontal beams to complete the structural aspects of the roof system . Steel header...included a mix of new construction and renovation of existing structures and facilities. The Statement of Requirements and Specifications provided...that renovation of existing structures , when possible, was preferred. In addition, the United States government encouraged the contractor to use

Joint Measurement Operations Controller (JMOC)

DTIC Science & Technology

2011-01-01

This work included evaluation of electronic paper and handwriting recognition software. Neither of these technologies was sufficiently robust to...is header information saying this is the Dynamic Targeting Cell set of questions. <Module webEnabled="false" appName="DTC" displayGlobalPre="true...translation of their handwriting captures. The one exception is Logitech, which provides its own software but is also compatible with MyScript Notes

1. 119 LOMBARD STREET, SECOND HOUSE TO LEFT (WITH BOARDEDUP ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

1. 119 LOMBARD STREET, SECOND HOUSE TO LEFT (WITH BOARDED-UP FIRST AND SECOND FLOOR WINDOWS). NOTE THAT THE FRONT (SOUTH) HAS BELT COURSES, GLAZED HEADERS, PLASTER COVE CORNICE, DOOR STOOP, ETC. ALSO NOTE THE TWIN HOUSE (117 LOMBARD STREET, HABS No. PA-1353) AT RIGHT, WITH IDENTICAL FEATURES. BOTH HOUSES WERE BUILT AT THE SAME TIME. - Joseph Wharton House, 119 Lombard Street, Philadelphia, Philadelphia County, PA

--No Title--

Science.gov Websites

{box-sizing:border-box}.fix{background-color:#ff0}.bio-title{color:#5e6a71;font-size:20px;margin-top:0 ,.8);color:#fff;padding:1em;position:absolute;text-align:left}h3 .more{color:#fff;font-size:65%;font -weight:400}.hpfeat .header{background-color:#00a3e4;border-bottom:5px solid #000;color:#000;font-size

Experiment for transient effects of sudden catastrophic loss of vacuum on a scaled superconducting radio frequency cryomodule

NASA Astrophysics Data System (ADS)

Dalesandro, Andrew A.; Theilacker, Jay; Van Sciver, Steven

2012-06-01

Safe operation of superconducting radio frequency (SRF) cavities require design consideration of a sudden catastrophic loss of vacuum (SCLV) adjacent with liquid helium (LHe) vessels and subsequent dangers. An experiment is discussed to test the longitudinal effects of SCLV along the beam line of a string of scaled SRF cavities. Each scaled cavity includes one segment of beam tube within a LHe vessel containing 2 K saturated LHe, and a riser pipe connecting the LHe vessel to a common gas header. At the beam tube inlet is a fast acting solenoid valve to simulate SCLV and a high/low range orifice plate flow-meter to measure air influx to the cavity. The gas header exit also has an orifice plate flow-meter to measure helium venting the system at the relief pressure of 0.4 MPa. Each cavity is instrumented with Validyne pressure transducers and Cernox thermometers. The purpose of this experiment is to quantify the time required to spoil the beam vacuum and the effects of transient heat and mass transfer on the helium system. Heat transfer data is expected to reveal a longitudinal effect due to the geometry of the experiment. Details of the experimental design criteria and objectives are presented.

Chip breaking system for automated machine tool

DOEpatents

Arehart, Theodore A.; Carey, Donald O.

1987-01-01

The invention is a rotary selectively directional valve assembly for use in an automated turret lathe for directing a stream of high pressure liquid machining coolant to the interface of a machine tool and workpiece for breaking up ribbon-shaped chips during the formation thereof so as to inhibit scratching or other marring of the machined surfaces by these ribbon-shaped chips. The valve assembly is provided by a manifold arrangement having a plurality of circumferentially spaced apart ports each coupled to a machine tool. The manifold is rotatable with the turret when the turret is positioned for alignment of a machine tool in a machining relationship with the workpiece. The manifold is connected to a non-rotational header having a single passageway therethrough which conveys the high pressure coolant to only the port in the manifold which is in registry with the tool disposed in a working relationship with the workpiece. To position the machine tools the turret is rotated and one of the tools is placed in a material-removing relationship of the workpiece. The passageway in the header and one of the ports in the manifold arrangement are then automatically aligned to supply the machining coolant to the machine tool workpiece interface for breaking up of the chips as well as cooling the tool and workpiece during the machining operation.

Non-vascular interventional procedures: effective dose to patient and equivalent dose to abdominal organs by means of DICOM images and Monte Carlo simulation.

PubMed

Longo, Mariaconcetta; Marchioni, Chiara; Insero, Teresa; Donnarumma, Raffaella; D'Adamo, Alessandro; Lucatelli, Pierleone; Fanelli, Fabrizio; Salvatori, Filippo Maria; Cannavale, Alessandro; Di Castro, Elisabetta

2016-03-01

This study evaluates X-ray exposure in patient undergoing abdominal extra-vascular interventional procedures by means of Digital Imaging and COmmunications in Medicine (DICOM) image headers and Monte Carlo simulation. The main aim was to assess the effective and equivalent doses, under the hypothesis of their correlation with the dose area product (DAP) measured during each examination. This allows to collect dosimetric information about each patient and to evaluate associated risks without resorting to in vivo dosimetry. The dose calculation was performed in 79 procedures through the Monte Carlo simulator PCXMC (A PC-based Monte Carlo program for calculating patient doses in medical X-ray examinations), by using the real geometrical and dosimetric irradiation conditions, automatically extracted from DICOM headers. The DAP measurements were also validated by using thermoluminescent dosemeters on an anthropomorphic phantom. The expected linear correlation between effective doses and DAP was confirmed with an R(2) of 0.974. Moreover, in order to easily calculate patient doses, conversion coefficients that relate equivalent doses to measurable quantities, such as DAP, were obtained. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

E-Science and Protein Crystallography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Miller, Laniece E.; Powell, James E. Jr.

2012-08-09

Dr. Zoe Fisher is the instrument scientist for the Protein Crystallography Station (PCS) at the Los Alamos Neutron Science Center's (LANSC) Lujan Neutron Scattering Center. She helps schedule researchers who intend to use the instrument to collect data, and provides in depth support for their activities. Users submit proposals for beam/instrument time via LANSCE proposal review system. In 2012, there were about 20 proposals submitted for this instrument. The instrument scientists review the proposals online. Accepted proposals are scheduled via an aggregate calendar which takes into account staff and resource availability, and the scientist is notified via email when theirmore » proposal is accepted and their requested time is scheduled. The entire PCS data acquisition and processing workflow is streamlined through various locally developed and commercial software packages. One 24 hour period produces one 200 Mb file, giving a total of maybe 2-5 Gb of data for the entire run. This data is then transferred to a hard disk in Dr. Fisher's office where she views the data with the customer and compresses the data to a text format which she sends them. This compression translates the data from an electron density to structural coordinates, which are the products submitted to a protein structure database. As noted above, the raw experimental data is stored onsite at LANSCE on workstations maintained by the instrument scientist. It is extraordinarily rare for anyone to request this data, although the remote possibility of an audit by a funding organization motivates its limited preservation. The raw data is not rigorously backed up, but only stored on a single hard drive. Interestingly, only about 50% of the experimental data actually ends up deposited and described in peer reviewed publications; the data that is not published tends to either not be viable structures or is calibration data. Dr. Fisher does protein crystallography research using both neutron and x-ray scattering techniques. Many of the major funders as well as the major journals dealing with protein crystallography require deposition of the structural data in the Protein Data Bank (PDB). Files formatted for the PDB are automatically generated when the data is compressed. The header files in the PDB included experimental conditions of the experiment as well as experimental methods. Depending on the completeness and how 'hot' of a topic, it may not be needed to contact the original experimenter about using the data. Having said that, not all of the data is accurate and does requires some back and forth with the creators of the data. The RCSB PDB staff at Rutgers University goes through all submissions and works with the submitters to verify that the data meets their minimum standards of completeness and robustness. The Protein Data Bank (PDB) was initially created by Walter Hamilton at Brookhaven National Laboratory in 1971 after discussions about the value of scientists having access to structural biology data. Originally a partnership between Brookhaven and the Cambridge Crystallographic Data Center, the idea was conceived as a global initiative, which is certainly has become with partner sites in the US, Europe, and Japan. The PDB now contains structures determined from many different experimental techniques (Berman et al. 2012). Deposited structures are assigned a unique ID, and the structures are embargoed until the publication that references and describes them is published. The PDB staff often monitors these publications and takes the initiative to release protein structures when papers describing them are published. Dr. Fisher records setup and experimental details in word documents and inserts printed copies into paper lab notebooks. These details appear in the final published papers and the header files for structures in the PDB. Analysis of data collected at the PCS is performed with a combination of locally developed tools and commercial products which are capable of outputting data suitable for importing into the PDB. While the original output data from the LANL instrument is stored indefinitely on a hard disk, the analysis results in a text file that, as described above, which represents the structure of the protein, which can be modeled and explored via tools that scientists in this domain have access to and are familiar with. The entire process is well understood and well-supported by software used by researchers in this field. The incorporation of the PDB into research-analysis-publication is embraced by the international community of researchers in this field. There are mirror depository sites for the PDB in several countries. Curation of the submitted protein structures is rigorous, although Dr. Fisher noted that some structures are rushed to publication with what she termed 'bogus filler', which is possible since protein structures are 50-70% water.« less

Closed loop engine control for regulating NOx emissions, using a two-dimensional fuel-air curve

DOEpatents

Bourn, Gary D.; Smith, Jack A.; Gingrich, Jess W.

2007-01-30

An engine control strategy that ensures that NOx emissions from the engine will be maintained at an acceptable level. The control strategy is based on a two-dimensional fuel-air curve, in which air manifold pressure (AMP) is a function of fuel header pressure and engine speed. The control strategy provides for closed loop NOx adjustment to a base AMP value derived from the fuel-air curve.

Development of a Multileaf Collimator for Proton Radiotherapy

DTIC Science & Technology

2006-06-01

voxel size and slice thickness can be adjusted and determine the resolution. Each voxel is assigned a CT Number, in Hounsfield units , which is a...measure of the linear attenuation of the material in that voxel. The Hounsfield unit is a comparison of the linear attenuation coefficient of some...a header, which contains relevant patient and scan information, and the data, which is a sequential listing of the Hounsfield units of each voxel

Method and Apparatus for Processing UDP Data Packets

NASA Technical Reports Server (NTRS)

Murphy, Brandon M. (Inventor)

2017-01-01

A method and apparatus for processing a plurality of data packets. A data packet is received. A determination is made as to whether a portion of the data packet follows a selected digital recorder standard protocol based on a header of the data packet. Raw data in the data packet is converted into human-readable information in response to a determination that the portion of the data packet follows the selected digital recorder standard protocol.

Configuration Tool Prototype for the Trusted Computing Exemplar Project

DTIC Science & Technology

2009-12-01

languages were examined: Microsoft .NET [8], Apple Cocoa (Objective-C) [9], wxPython [10], and Java [11]. Since every language has its pros and...languages using the criteria described above. Based on the developer’s limited experience and knowledge of Microsoft .NET and Apple Cocoa (Objective...a tabbed panel within a separate window panel. Figure 9 depicts this evolution of the conceptual design. In Figure 9, the table column headers are

High temperature solar thermal receiver

NASA Technical Reports Server (NTRS)

1979-01-01

A design concept for a high temperature solar thermal receiver to operate at 3 atmospheres pressure and 2500 F outlet was developed. The performance and complexity of windowed matrix, tube-header, and extended surface receivers were evaluated. The windowed matrix receiver proved to offer substantial cost and performance benefits. An efficient and cost effective hardware design was evaluated for a receiver which can be readily interfaced to fuel and chemical processes or to heat engines for power generation.

Forwarding techniques for IP fragmented packets in a real 6LoWPAN network.

PubMed

Ludovici, Alessandro; Calveras, Anna; Casademont, Jordi

2011-01-01

Wireless Sensor Networks (WSNs) are attracting more and more interest since they offer a low-cost solution to the problem of providing a means to deploy large sensor networks in a number of application domains. We believe that a crucial aspect to facilitate WSN diffusion is to make them interoperable with external IP networks. This can be achieved by using the 6LoWPAN protocol stack. 6LoWPAN enables the transmission of IPv6 packets over WSNs based on the IEEE 802.15.4 standard. IPv6 packet size is considerably larger than that of IEEE 802.15.4 data frame. To overcome this problem, 6LoWPAN introduces an adaptation layer between the network and data link layers, allowing IPv6 packets to be adapted to the lower layer constraints. This adaptation layer provides fragmentation and header compression of IP packets. Furthermore, it also can be involved in routing decisions. Depending on which layer is responsible for routing decisions, 6LoWPAN divides routing in two categories: mesh under if the layer concerned is the adaptation layer and route over if it is the network layer. In this paper we analyze different routing solutions (route over, mesh under and enhanced route over) focusing on how they forward fragments. We evaluate their performance in terms of latency and energy consumption when transmitting IP fragmented packets. All the tests have been performed in a real 6LoWPAN implementation. After consideration of the main problems in forwarding of mesh frames in WSN, we propose and analyze a new alternative scheme based on mesh under, which we call controlled mesh under.

Forwarding Techniques for IP Fragmented Packets in a Real 6LoWPAN Network

PubMed Central

Ludovici, Alessandro; Calveras, Anna; Casademont, Jordi

2011-01-01

Wireless Sensor Networks (WSNs) are attracting more and more interest since they offer a low-cost solution to the problem of providing a means to deploy large sensor networks in a number of application domains. We believe that a crucial aspect to facilitate WSN diffusion is to make them interoperable with external IP networks. This can be achieved by using the 6LoWPAN protocol stack. 6LoWPAN enables the transmission of IPv6 packets over WSNs based on the IEEE 802.15.4 standard. IPv6 packet size is considerably larger than that of IEEE 802.15.4 data frame. To overcome this problem, 6LoWPAN introduces an adaptation layer between the network and data link layers, allowing IPv6 packets to be adapted to the lower layer constraints. This adaptation layer provides fragmentation and header compression of IP packets. Furthermore, it also can be involved in routing decisions. Depending on which layer is responsible for routing decisions, 6LoWPAN divides routing in two categories: mesh under if the layer concerned is the adaptation layer and route over if it is the network layer. In this paper we analyze different routing solutions (route over, mesh under and enhanced route over) focusing on how they forward fragments. We evaluate their performance in terms of latency and energy consumption when transmitting IP fragmented packets. All the tests have been performed in a real 6LoWPAN implementation. After consideration of the main problems in forwarding of mesh frames in WSN, we propose and analyze a new alternative scheme based on mesh under, which we call controlled mesh under. PMID:22346615

Incorporating the APS Catalog of the POSS I and Image Archive in ADS

NASA Technical Reports Server (NTRS)

Humphreys, Roberta M.

1998-01-01

The primary purpose of this contract was to develop the software to both create and access an on-line database of images from digital scans of the Palomar Sky Survey. This required modifying our DBMS (called Star Base) to create an image database from the actual raw pixel data from the scans. The digitized images are processed into a set of coordinate-reference index and pixel files that are stored in run-length files, thus achieving an efficient lossless compression. For efficiency and ease of referencing, each digitized POSS I plate is then divided into 900 subplates. Our custom DBMS maps each query into the corresponding POSS plate(s) and subplate(s). All images from the appropriate subplates are retrieved from disk with byte-offsets taken from the index files. These are assembled on-the-fly into a GIF image file for browser display, and a FITS format image file for retrieval. The FITS images have a pixel size of 0.33 arcseconds. The FITS header contains astrometric and photometric information. This method keeps the disk requirements manageable while allowing for future improvements. When complete, the APS Image Database will contain over 130 Gb of data. A set of web pages query forms are available on-line, as well as an on-line tutorial and documentation. The database is distributed to the Internet by a high-speed SGI server and a high-bandwidth disk system. URL is http://aps.umn.edu/IDB/. The image database software is written in perl and C and has been compiled on SGI computers with MIX5.3. A copy of the written documentation is included and the software is on the accompanying exabyte tape.

34. (Credit JTL) Front (north side) of three water tube ...

Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

34. (Credit JTL) Front (north side) of three water tube boilers built by the Heine Safety Boiler Co. of St. Louis, Missouri in 1917; rebuilt in 1938. Front doors opened on center boiler to show water header and inspection plugs for water tubes. Smaller doors beneath open into firebox; boilers presently equipped for gas firing. Operating pressure approx. 150 psi (saturated steam). - McNeil Street Pumping Station, McNeil Street & Cross Bayou, Shreveport, Caddo Parish, LA

Advanced Technology Multiple Criteria Decision Model.

DTIC Science & Technology

1981-11-01

ratings of the sys- tem parameters; and (3), HEADER which contains information on the structure of the problem and titles. Two supporting programs develop...in these files are given in Section V.2. 2. DATA STRUCTURE TABLES This section describes the data files used in the system selection model program ...the supporting program PPP and an input file to UPPP and SSMP. Figure 13 shows the structure of this file. b. User’s preference package (UPP) UPP is

SODIUM-WATER HEAT EXCHANGER

DOEpatents

Simmons, W.R.; Koch, L.J.

1962-04-17

A heat exchanger comprising a tank for hot liquid and a plurality of concentric, double tubes for cool liquid extending vertically through the tank is described. These tubes are bonded throughout most of their length but have an unbonded portion at both ends. The inner tubes extend between headers located above and below the tanmk and the outer tubes are welded into tube sheets forming the top and bottom of the tank at locations in the unbonded portions of the tubes. (AEC)

Bandwidth and Detection of Packet Length Covert Channels

DTIC Science & Technology

2011-03-01

Shared Resource Matrix ( SRM ): Develop a matrix of all resources on one side and on the other all the processes. Then, determine which process uses which...system calls. This method is similar to that of the SRM . Covert channels have also been created by modulating packet timing, data and headers of net- work...analysis, noninterference analysis, SRM method, and the covert flow tree method [4]. These methods can be used during the design phase of a system. Less

Standardized UXO Technology Demonstration Site Blind Grid Scoring Record No. 805

DTIC Science & Technology

2007-03-01

and receiver (RX) coils. b. The Tensor Magnetic Gradiometer System ( TMGS ) has been reconfigured to improve its performance compared with the...ALL TEM. The TMGS raw data files consist of an ASCII header with system settings followed by the data in binary format. The GPS positions, EDA...exported in ASCII format. A new data acquisition system for the TMGS will be supplied by the demonstrator. It is controlled by LabVIEW, as is the ALL

Large Diameter, High Speed InGaAs Receivers for Free-Space Lasercom

DTIC Science & Technology

2007-01-01

appropriate transimpedance amplifier and limiting amplifier . Development and testing of the APD receivers will be described below. 15. SUBJECT TERMS 16...available transimpedance amplifiers (TIA) from Maxim of Dallas. There have also been several devices built in house by NRL in 8-pin TO-39 headers...manufacture a large area, high speed InGaAs APD with an effective ionization ratio of < 0.2 and by matching the APD device with an appropriate transimpedance

Performance Improvements of the Phoneme Recognition Algorithm.

DTIC Science & Technology

1984-06-01

VECTOR NUNDIRt"tIVECTj Beginning vector ; of speech to be extracted INDEX * MOD(IVECT,4) ICheck for vector being ; last vector in block 63 ILE u ((JUICT...1fIER0) ; Read header block. CALL CHECK(IERO) IHEADER(57) : ICOfP ; Change a of freq. components ICHECK : (IHEADER(56) - ([LENGTH - 1)) * ILENGTH...ICONT .Al. ICHECK ) GO TO 55 ; Check to make sure correct ;amount of vectors have been created# INCR u INCR + 32 ;Jump over last set of components

Ada Quality and Style: Guidelines for Professional Programmers

DTIC Science & Technology

1989-01-01

Paes. Enter the total Block 7. Performing Organization Name(s) and number of pages.AccLpr., A). Self-explanatory. Block 16. Price.o de Enter...parts of typical header comment blocks. Including other, de facto extraneous or superfluous information is a waste of time. Most of the information...specification and to export only what is necessary for another unit to use the package properly. Visibility of objects such as DEFAULT.3IDT.t in package TEXTo

Very High-Speed Report File System

DTIC Science & Technology

1992-12-15

1.5 and 45 Mb/s and is expected 1 Introduction to reach 150 Mb/s. These new technologies pose some challenges to The Internet Protocol (IP) family (IP... Internet Engineering Task Force (IETF) has R taken up the issue, but a definitive answer is probably some time away. The basic issues are the choice of AAL...by an IEEE 802. la Subnetwork Access Protocol (SNAP) However, with a large number of networks all header. The third proposal identifies the protocol

A Prototype Two-Level Multicomputer Study

DTIC Science & Technology

1999-01-01

Wakeup : When this input is asserted, the wakeJnt bit in the special register ISR (Interrupt Status Register) is set. 43 MYRINET SAN INTERFACE Pin...including the double-word pointed to by RMC, the headJnt bit of ISR is set (page 10). RMW Receive-Message Header Wakeup : This is the same physical register...Register) are both equal to 1. WAKE synch. I Wakeup : When this input is asserted, the wakeJnt bit in the special register ISR (Interrupt Status

DOE Zero Energy Ready Home Case Study: Palo Duro Homes, Albuquerque, New Mexico

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2013-09-01

Palo Duro uses advanced framing techniques like 2x6 24-inch on-center framing, open headers above windows on non-load-bearing walls, 2-stud corners, ladder blocking where walls intersect, and single top and bottom plates. These techniques reduce the amount of lumber in the wall, allowing more room for insulation and reducing costs and installation time. The builder garnered a 2013 Housing Innovation Award in the production builder category.

A secure transmission scheme of streaming media based on the encrypted control message

NASA Astrophysics Data System (ADS)

Li, Bing; Jin, Zhigang; Shu, Yantai; Yu, Li

2007-09-01

As the use of streaming media applications increased dramatically in recent years, streaming media security becomes an important presumption, protecting the privacy. This paper proposes a new encryption scheme in view of characteristics of streaming media and the disadvantage of the living method: encrypt the control message in the streaming media with the high security lever and permute and confuse the data which is non control message according to the corresponding control message. Here the so-called control message refers to the key data of the streaming media, including the streaming media header and the header of the video frame, and the seed key. We encrypt the control message using the public key encryption algorithm which can provide high security lever, such as RSA. At the same time we make use of the seed key to generate key stream, from which the permutation list P responding to GOP (group of picture) is derived. The plain text of the non-control message XORs the key stream and gets the middle cipher text. And then obtained one is permutated according to P. In contrast the decryption process is the inverse process of the above. We have set up a testbed for the above scheme and found our scheme is six to eight times faster than the conventional method. It can be applied not only between PCs but also between handheld devices.

Review of Cuttability Indices and A New Rockmass Classification Approach for Selection of Surface Miners

NASA Astrophysics Data System (ADS)

Dey, Kaushik; Ghose, A. K.

2011-09-01

Rock excavation is carried out either by drilling and blasting or using rock-cutting machines like rippers, bucket wheel excavators, surface miners, road headers etc. Economics of mechanised rock excavation by rock-cutting machines largely depends on the achieved production rates. Thus, assessment of the performance (productivity) is important prior to deploying a rock-cutting machine. In doing so, several researchers have classified rockmass in different ways and have developed cuttability indices to correlate machine performance directly. However, most of these indices were developed to assess the performance of road headers/tunnel-boring machines apart from a few that were developed in the earlier days when the ripper was a popular excavating equipment. Presently, around 400 surface miners are in operation around the world amongst which, 105 are in India. Until now, no rockmass classification system is available to assess the performance of surface miners. Surface miners are being deployed largely on trial and error basis or based on the performance charts provided by the manufacturer. In this context, it is logical to establish a suitable cuttability index to predict the performance of surface miners. In this present paper, the existing cuttability indices are reviewed and a new cuttability indexes proposed. A new relationship is also developed to predict the output from surface miners using the proposed cuttability index.

RADIANCE: An automated, enterprise-wide solution for archiving and reporting CT radiation dose estimates.

PubMed

Cook, Tessa S; Zimmerman, Stefan L; Steingall, Scott R; Maidment, Andrew D A; Kim, Woojin; Boonn, William W

2011-01-01

There is growing interest in the ability to monitor, track, and report exposure to radiation from medical imaging. Historically, however, dose information has been stored on an image-based dose sheet, an arrangement that precludes widespread indexing. Although scanner manufacturers are beginning to include dose-related parameters in the Digital Imaging and Communications in Medicine (DICOM) headers of imaging studies, there remains a vast repository of retrospective computed tomographic (CT) data with image-based dose sheets. Consequently, it is difficult for imaging centers to monitor their dose estimates or participate in the American College of Radiology (ACR) Dose Index Registry. An automated extraction software pipeline known as Radiation Dose Intelligent Analytics for CT Examinations (RADIANCE) has been designed that quickly and accurately parses CT dose sheets to extract and archive dose-related parameters. Optical character recognition of information in the dose sheet leads to creation of a text file, which along with the DICOM study header is parsed to extract dose-related data. The data are then stored in a relational database that can be queried for dose monitoring and report creation. RADIANCE allows efficient dose analysis of CT examinations and more effective education of technologists, radiologists, and referring physicians regarding patient exposure to radiation at CT. RADIANCE also allows compliance with the ACR's dose reporting guidelines and greater awareness of patient radiation dose, ultimately resulting in improved patient care and treatment.

LEGO plot for simultaneous application of multiple quality requirements during trueness verification of quantitative laboratory tests.

PubMed

Park, Hae-il; Chae, Hyojin; Kim, Myungshin; Lee, Jehoon; Kim, Yonggoo

2014-03-01

We developed a two-dimensional plot for viewing trueness that takes into account potential shift and variable quality requirements to verify trueness using certified reference material (CRM). Glucose, total cholesterol (TC), and creatinine levels were determined by two kinds of assay in two levels of a CRM. Available quality requirements were collected, codified, and sorted in an ascending order in the plot's header row. Centering on the mean of measured values from CRM, the "mean ± US CLIA '88 allowable total error" was located in the header of the leftmost and rightmost columns. Twenty points were created in intervening columns as potential shifts. Uncertainties were calculated according to regression between certified values and uncertainties of CRM, and positioned in the corresponding columns. Cells were assigned different colors where column and row intersected based on comparison of the 95% confidence interval of the percentage bias with each quality requirement. A glucose assay failed to meet the highest quality criteria, for which shift of +0.13-0.14 mmol/l was required. A TC assay met the quality requirement and a shift of ±0.03 mmol/l was tolerable. A creatinine assay also met the quality requirement but any shift was not tolerable. The plot provides a systematic view of the trueness of quantitative laboratory tests. © 2014 Wiley Periodicals, Inc.

An optical disk archive for a data base management system

NASA Technical Reports Server (NTRS)

Thomas, Douglas T.

1985-01-01

An overview is given of a data base management system that can catalog and archive data at rates up to 50M bits/sec. Emphasis is on the laser disk system that is used for the archive. All key components in the system (3 Vax 11/780s, a SEL 32/2750, a high speed communication interface, and the optical disk) are interfaced to a 100M bits/sec 16-port fiber optic bus to achieve the high data rates. The basic data unit is an autonomous data packet. Each packet contains a primary and secondary header and can be up to a million bits in length. The data packets are recorded on the optical disk at the same time the packet headers are being used by the relational data base management software ORACLE to create a directory independent of the packet recording process. The user then interfaces to the VAX that contains the directory for a quick-look scan or retrieval of the packet(s). The total system functions are distributed between the VAX and the SEL. The optical disk unit records the data with an argon laser at 100M bits/sec from its buffer, which is interfaced to the fiber optic bus. The same laser is used in the read cycle by reducing the laser power. Additional information is given in the form of outlines, charts, and diagrams.

ISDEC-2 and ISDEC-3 controllers for HAWAII detectors

NASA Astrophysics Data System (ADS)

Burse, Mahesh; Ramaprakash, A. N.; Chordia, Pravinkumar; Punnadi, Sujit; Chillal, Kalpesh; Mestri, Vilas; Bharti, Rupali; Sinha, Sakya; Kohok, Abhay

2016-07-01

ISDEC-2 - IUCAA1 SIDECAR Drive Electronics Controller is an alternative for Teledyne make JADE2 based controller for HAWAII detectors. It is a ready to use complete package and has been developed keeping in mind general astronomical requirements and widely used observatory set-ups like preferred OS-Linux , multi-extension fits output with fully populated headers (with detector as well as telescope and observation specific information), etc. Actual exposure time is measured for each frame to a few tens of microsecond accuracy and put in the fits header. It also caters to several application specific requirements like fast resets, strip mode, multiple region readout with on board co-adding, etc. ISDEC-2 is designed to work at -40 deg. and is already in use at observatories worldwide. ISDEC-3 is an Artix-7 FPGA based SIDECAR Drive Electronics Controller currently being developed at IUCAA. It will retain all the functionality supported by ISDEC-2 and will also support the operation of H2RG in continuos, fast (32 output, 5 MSPS, 12 bit) mode. It will have a 5 Gbps USB 3.0 PC interface and 1 Gbps Ethernet interface for image data transfer from SIDECAR to host PC. Additionally, the board will have DDR-3 memory for on-board storage and processing. ISDEC-3 will be capable of handling two SIDECARs simultaneously (in sync) for H2RG slow modes.

Non-blocking crossbar permutation engine with constant routing latency

NASA Technical Reports Server (NTRS)

Monacos, Steve P. (Inventor)

1994-01-01

The invention is embodied in an N x N crossbar for routing packets from a set of N input ports to a set of N output ports, each packet having a header identifying one of the output ports as its destination, including a plurality of individual links which carry individual packets. Each link has a link input end and a link output end, a plurality of switches. Each of the switches has at least top and bottom switch inputs connected to a corresponding pair of the link output ends and top and bottom switch outputs connected to a corresponding pair of link input ends, whereby each switch is connected to four different links. Each of the switches has an exchange state which routes packets from the top and bottom switch inputs to the bottom and top switch outputs, respectively, and a bypass state which routes packets from the top and bottom switch inputs to the top and bottom switch outputs, respectively. A plurality of individual controller devices governing respective switches for sensing from a header of a packet at each switch input for the identity of the destination output port of the packet and selecting one of the exchange and bypass states in accordance with the identity of the destination output port and with the location of the corresponding switch relative to the destination output port.

Assessing the impact of a radiology information management system in the emergency department

NASA Astrophysics Data System (ADS)

Redfern, Regina O.; Langlotz, Curtis P.; Lowe, Robert A.; Horii, Steven C.; Abbuhl, Stephanie B.; Kundel, Harold L.

1998-07-01

To evaluate a conventional radiology image management system, by investigating information accuracy, and information delivery. To discuss the customization of a picture archival and communication system (PACS), integrated radiology information system (RIS) and hospital information system (HIS) to a high volume emergency department (ED). Materials and Methods: Two data collection periods were completed. After the first data collection period, a change in work rules was implemented to improve the quality of data in the image headers. Data from the RIS, the ED information system, and the HIS as well as observed time motion data were collected for patients admitted to the ED. Data accuracy, patient waiting times, and radiology exam information delivery were compared. Results: The percentage of examinations scheduled in the RIS by the technologists increased from 0% (0 of 213) during the first period to 14% (44 of 317) during the second (p less than 0.001). The percentage of images missing identification numbers decreased from 36% (98 of 272) during the first data collection period to 10% (56 of 562) during the second period (p less than 0.001). Conclusions: Radiologic services in a high-volume ED, requiring rapid service, present important challenges to a PACS system. Strategies can be implemented to improve accuracy and completeness of the data in PACS image headers in such an environment.

Traffic-Aware Channel Allocation and Routing in Multichannel, Multi-Radio Wireless Networks

DTIC Science & Technology

2012-01-01

come up with interesting ideas that eventually led me to my Ph.D. research topic that is presented in the Chapter 5 of this disserta- tion. Next, I...exam process. Their comments and suggestions helped me im- prove my research topic and project it in a perspective suitable for a wider audience. I...backo , and xed rate header transmissions. These overheads become prominent in short packets that are transmitted at high data rates. We address this

Using the Auditory Hazard Assessment Algorithm for Humans (AHAAH) Software, Beta Release W93e

DTIC Science & Technology

2009-09-01

Hazard Assessment Algorithm for Humans (AHAAH) Does The AHAAH is an electro- acoustic model of the ear used to evaluate the hazard of impulse sounds...format is commonly used for recording music ; thus, these are typically stereo files and contain a “right” and a “left” channel as well as a header... acoustic data (sometimes deliberately induced in recording to maximize the digitizer’s dynamic range), it must be removed. When Set Baseline is

Vectors and Rotations in 3-Dimensions: Vector Algebra for the C++ Programmer

DTIC Science & Technology

2016-12-01

Proving Ground, MD 21005-5068 This report describes 2 C++ classes: a Vector class for performing vector algebra in 3-dimensional space ( 3D ) and a Rotation...class for performing rotations of vectors in 3D . Each class is self-contained in a single header file (Vector.h and Rotation.h) so that a C...vector, rotation, 3D , quaternion, C++ tools, rotation sequence, Euler angles, yaw, pitch, roll, orientation 98 Richard Saucier 410-278-6721Unclassified

DOE Office of Scientific and Technical Information (OSTI.GOV)

Llopis, C.; Mendizabal, R.; Perez, J.

An assessment of RELAP5/MOD2 cycle 36.04 against a load rejection from 100% to 50% power in Vandals II NPP (Spain) is presented. The work is inscribed in the framework of the Spanish contribution to ICAP Project. The model used in the simulation consists of a single loop, a steam generator and a steam line up to the steam header all of them enlarged on a scale of 3:1, and full-scaled reactor vessel and pressurizer. The results of the calculations have been in reasonable agreement with plant measurements.

Evaluating Connectivity between Marine Protected Areas Using CODAR High-Frequency Radar

DTIC Science & Technology

2010-06-01

SMCA/SMR, (6) Big Creek SMCA/SMR, (7) Piedras Blancas SMCA/SMR, (8) Cambria SMCA/White Rock SMCA, (9) Pt. Buchon SMCA/SMR, and (10) Vandenberg SMR...52 grid- points, (7) Piedras Blancas 47 grid-points, (8) Cambria 20 grid-points, (9) Pt. Buchon 45 grid- points, and (10) the Vandenberg MPA had 62...COLUMN HEADERS. Back-projected from: (Sorted north- to-south) Año Nuevo Soquel Canyon Portuguese Ledge Point Lobos Point Sur Big Creek Piedras

Compact organic vapor jet printing print head

DOEpatents

Forrest, Stephen R; McGraw, Gregory

2013-12-24

A first device is provided. The first device includes a print head, and a first gas source hermetically sealed to the print head. The print header further includes a first layer comprising a plurality of apertures, each aperture having a smallest dimension of 0.5 to 500 microns. A second layer is bonded to the first layer. The second layer includes a first via in fluid communication with the first gas source and at least one of the apertures. The second layer is made of an insulating material.

Space tug thermal control follow-on

NASA Technical Reports Server (NTRS)

Ward, T. L.

1975-01-01

The Space Tug Thermal Control Follow-On program was conducted to further explore some of the thermal control concepts proposed for use in space tug in a breadboard test program. The objectives were to demonstrate the thermal control capabilities of a louver/battery configuration and a thermal conditioning panel/heat pipe radiator configuration. An additional objective was added to model the header pipe and radiator of the second test and correlate the analysis with the test results. These three objectives were achieved and are discussed within this report.

Duct Protection Coating Concept Development and Test

DTIC Science & Technology

1993-01-01

20 AEDC-TR-92 23 next to the virgin steel. At this time it was also learned that the "A" header has been previously painted. This raised several...mortar and pestle . Some samples were easier to powder than others and, therefore, the fineness of gnnd varied somewhat. In those cases where the rust...powder using a mortar and pestle . This rust is not as tenaciously held to the base metal as that found in the ducts. In general, the salt spray

As-built design specification for the CLASFYG program

NASA Technical Reports Server (NTRS)

Horton, C. L. (Principal Investigator)

1981-01-01

This program produces a file with a Universal-formatted header and data records in a nonstandard format. Trajectory coefficients are calculated from 5 to 8 acquisitions of radiance values in the training field corresponding to an agricultural product. These coefficients are then used to calculate a time of emergence and corresponding trajectory coefficients for each pixel in the test field. The time of emergence, two of the coefficients, and the sigma value for each pixel are written to the file.

Video Coding and the Application Level Framing Protocol Architecture

DTIC Science & Technology

1992-06-01

missing ADU can be sent to the decoder when and if it arrives. The need for out-of- order processing arises for two reasons. First, ADUs may be reordered...by the network. Second, an ADU which is lost and then successfully retransmitted will arrive out of order. In either case, out-of- order processing makes...the code do not allow at least some out-of- order processing , one of the strong points of the ALF architecture is eliminated. 2.3.4 Header Data

FPGA and USB based control board for quantum random number generator

NASA Astrophysics Data System (ADS)

Wang, Jian; Wan, Xu; Zhang, Hong-Fei; Gao, Yuan; Chen, Teng-Yun; Liang, Hao

2009-09-01

The design and implementation of FPGA-and-USB-based control board for quantum experiments are discussed. The usage of quantum true random number generator, control- logic in FPGA and communication with computer through USB protocol are proposed in this paper. Programmable controlled signal input and output ports are implemented. The error-detections of data frame header and frame length are designed. This board has been used in our decoy-state based quantum key distribution (QKD) system successfully.

100 GB/S Time Division Multiplex (TDM) Access Nodes and Regenerators Based on Novel Loop Mirrors with High Nonlinearity Fibers

DTIC Science & Technology

2002-07-01

spectral components remain co-polarized. We confirmed that this was the case by passing the continuum through a polarizing beam splitter . The...propagation direction through polarization beam splitters and aligned along the other axis of the fiber. Co-propagating control and signal pulses...amplifier, PBS = polarization beam splitter . Figure 8. Eye diagram of header processor. This is the trace of the eye diagrams taken with the setup of Fig

Discovering weighted patterns in intron sequences using self-adaptive harmony search and back-propagation algorithms.

PubMed

Huang, Yin-Fu; Wang, Chia-Ming; Liou, Sing-Wu

2013-01-01

A hybrid self-adaptive harmony search and back-propagation mining system was proposed to discover weighted patterns in human intron sequences. By testing the weights under a lazy nearest neighbor classifier, the numerical results revealed the significance of these weighted patterns. Comparing these weighted patterns with the popular intron consensus model, it is clear that the discovered weighted patterns make originally the ambiguous 5SS and 3SS header patterns more specific and concrete.

Discovering Weighted Patterns in Intron Sequences Using Self-Adaptive Harmony Search and Back-Propagation Algorithms

PubMed Central

Wang, Chia-Ming; Liou, Sing-Wu

2013-01-01

A hybrid self-adaptive harmony search and back-propagation mining system was proposed to discover weighted patterns in human intron sequences. By testing the weights under a lazy nearest neighbor classifier, the numerical results revealed the significance of these weighted patterns. Comparing these weighted patterns with the popular intron consensus model, it is clear that the discovered weighted patterns make originally the ambiguous 5SS and 3SS header patterns more specific and concrete. PMID:23737711

GMSEC Interface Specification Document 2016 March

NASA Technical Reports Server (NTRS)

Handy, Matthew

2016-01-01

The GMSEC Interface Specification Document contains the standard set of defined messages. Each GMSEC standard message contains a GMSEC Information Bus Header section and a Message Contents section. Each message section identifies required fields, optional fields, data type and recommended use of the fields. Additionally, this document includes the message subjects associated with the standard messages. The system design of the operations center should ensure the components that are selected use both the API and the defined standard messages in order to achieve full interoperability from component to component.

MT3DMS: A Modular Three-Dimensional Multispecies Transport Model for Simulation of Advection, Dispersion, and Chemical Reactions of Contaminants in Groundwater Systems; Documentation and User’s Guide

DTIC Science & Technology

1999-12-01

addition, the data files saved in the POINT format can include an optional header which is compatible with Amtec Engineering’s 2-D and 3-D visualization...34.DAT" file so that the file can be used directly by Amtec Engineering’s 2-D and 3-D visualization package Tecplot©. The ARRAY and POINT formats are

ROStoJAUSBridge Manual

DTIC Science & Technology

2012-03-01

Description A dass that handles Imming the JAUS header pmUon of JAUS messages. jaus_hmd~_msg is included as a data member in all JAUS messages. Member...scaleTolnt16 (float val, float low, float high) [related] Scales signed short value val, which is bounded by low and high. Shifts the center point of low...and high to zero, and shifts val accordingly. V a! is then up scaled by the ratio of the range of short values to the range of values from high to low

MO-E-17A-01: BEST IN PHYSICS (IMAGING) - Calculating SSDE From CT Exams Using Size Data Available in the DICOM Header of CT Localizer Radiographs

DOE Office of Scientific and Technical Information (OSTI.GOV)

McMillan, K; Bostani, M; McNitt-Gray, M

2014-06-15

Purpose: To demonstrate the feasibility of using existing data stored within the DICOM header of certain CT localizer radiographs as a patient size metric for calculating CT size-specific dose estimates (SSDE). Methods: For most Siemens CT scanners, the CT localizer radiograph (topogram) contains a private DICOM field that stores an array of numbers describing AP and LAT attenuation-based measures of patient dimension. The square root of the product of the AP and LAT size data, which provides an estimate of water-equivalent-diameter (WED), was calculated retrospectively from topogram data of 20 patients who received clinically-indicated abdomen/pelvis (n=10) and chest (n=10) scansmore » (WED-topo). In addition, slice-by-slice water-equivalent-diameter (WED-image) and effective diameter (ED-image) values were calculated from the respective image data. Using TG-204 lookup tables, size-dependent conversion factors were determined based upon WED-topo, WED-image and ED-image values. These conversion factors were used with the reported CTDIvol to calculate slice-by-slice SSDE for each method. Averaging over all slices, a single SSDE value was determined for each patient and size metric. Patientspecific SSDE and CTDIvol values were then compared with patientspecific organ doses derived from detailed Monte Carlo simulations of fixed tube current scans. Results: For abdomen/pelvis scans, the average difference between liver dose and CTDIvol, SSDE(WED-topo), SSDE(WED-image), and SSDE(ED-image) was 18.70%, 8.17%, 6.84%, and 7.58%, respectively. For chest scans, the average difference between lung dose and CTDIvol, SSDE(WED-topo), SSDE(WED-image), and SSDE(ED-image) was 25.80%, 3.33%, 4.11%, and 7.66%, respectively. Conclusion: SSDE calculated using WED derived from data in the DICOM header of the topogram was comparable to SSDE calculated using WED and ED derived from axial images; each of these estimated organ dose to within 10% for both abdomen/pelvis and chest CT examinations. The topogrambased method has the advantage that WED data are already provided and therefore available without additional post-processing of the image data. Funding Support: NIH Grant R01-EB017095; Disclosures - Michael McNitt-Gray: Institutional Research Agreement, Siemens AG; Research Support, Siemens AG; Consultant, Flaherty Sensabaugh Bonasso PLLC; Consultant, Fulbright and Jaworski; Disclosures - Cynthia McCollough: Research Grant, Siemens Healthcare.« less

Current status of final design and R&D for ITER blanket shield blocks in Korea

NASA Astrophysics Data System (ADS)

Ha, M. S.; Kim, S. W.; Jung, H. C.; Hwang, H. S.; Heo, Y. G.; Kim, D. H.; Ahn, H. J.; Lee, H. G.; Jung, K. J.

2015-07-01

The main function of the ITER blanket shield block (SB) is to provide nuclear shielding and support the first wall (FW) panel. It needs to accommodate all the components located on the vacuum vessel (in particular the in-vessel coils, blanket manifolds and the diagnostics). The conceptual, preliminary and final design reviews have been completed in the framework of the Blanket Integrated Product Team. The Korean Domestic Agency has successfully completed not only the final design activities, including thermo-hydraulic and thermo-mechanical analyses for SBs #2, #6, #8 and #16, but also the SB full scale prototype (FSP) pre-qualification program prior to issuing of the procurement agreement. SBs #2 and #6 are located at the in-board region of the tokamak. The pressure drop was less than 0.3 MPa and fully satisfied the design criteria. The thermo-mechanical stresses were also allowable even though the peak stresses occurred at nearby radial slit end holes, and their fatigue lives were evaluated over many more than 30 000 cycles. SB #8 is one of the most difficult modules to design, since this module will endure severe thermal loading not only from nuclear heating but also from plasma heat flux at uncovered regions by the FW. In order to resolve this design issue, the neutral beam shine-through module concept was applied to the FW uncovered region and it has been successfully verified as a possible design solution. SB #16 is located at the out-board central region of the tokamak. This module is under much higher nuclear loading than other modules and is covered by an enhanced heat flux FW panel. In the early design stage, many cooling headers on the front region were inserted to mitigate peak stresses near the access hole and radial slit end hole. However, the cooling headers on the front region needed to be removed in order to reduce the risk from cover welding during manufacturing. A few cooling headers now remain after efforts through several iterations to remove them and to optimize the cooling channels. The SB #8 FSP was manufactured and tested in accordance with the pre-qualification program based on the preliminary design, and related R&D activities were implemented to resolve the fabrication issues. This paper provides the current status of the final design and relevant R&D activities of the blanket SB.

Vibration Resistant Quartz Crystal Resonators.

DTIC Science & Technology

1981-01-01

HEADER T - il L~ ?RbiMOUNT:. A. 12 BOND METHOD : MARKING DETAIL SPECIFICATIONS SPEC: Y 1Q3 TOP SERNO’S FREQ. CAL. AT : . . -0!R’F FREQ. TOL. : * zo3 VA...Labs PO Box 12211 ATTN: ETL- TD -EA 002 Rsch Triangle Pk, NC 27709 001 Fort Belvoir, VA 22060 533 Commandant 571 Dir, Applied Tech Lab USA Inst for...D Command ATTN: DELHD-CO, TD (In Turn) 000 Fort Monmouth, NJ 07703 2800 Powder Mill Road 001 Adelphi, MD 20783 1 .DRDCO-COM-RO 1 USMC-LNO 608 Cdr

Inadvertent transposition of defibrillator coil terminal pins causing inappropriate ICD therapies.

PubMed

Issa, Ziad F

2008-06-01

We report the case of a 65-year-old man with chronic atrial fibrillation (AF) and severe ischemic cardiomyopathy who underwent implantation of a prophylactic single-chamber implantable cardioverter-defibrillator (ICD). The patient experienced inappropriate ICD therapies due to oversensing of pectoral muscle myopotential secondary to reversal of the defibrillator coil terminal pins in the ICD header. Recognizing this possibility is important to avoid misinterpretation of spontaneous oversensing as hardware failure (e.g., lead fracture or insulation breech) and potentially unnecessary ICD system surgical intervention, including lead extraction.

Corrigendum to "Infrared spectroscopy of 17O- and 18O-enriched carbon dioxide. Line positions and intensities in the 3200-4700 cm-1 region. Global modelling of the line positions of 16O12C17O and 17O12C17O" [J. Quant. Spectrosc. Radiat. Transfer 137 (2014) 57-76

NASA Astrophysics Data System (ADS)

Borkov, Yu. G.; Jacquemart, D.; Lyulin, O. M.; Tashkun, S. A.; Perevalov, V. I.

2015-05-01

In Supplementary Material I of our paper the observed line intensities are given for the abundances of the carbon dioxide isotopologues in our sample but not for 100% abundance as it is written in the header of Supplementary Material I. The respective abundances are presented in the table below.

Li corrosion resistant glasses for headers in ambient temperature Li batteries

DOEpatents

Hellstrom, E.E.; Watkins, R.D.

1985-10-11

Glass compositions containing 10 to 50 mol% CaO, 10 to 50 mol% Al/sub 2/O/sub 3/, 30 to 60 mol% B/sub 2/O/sub 3/, and 0 to 30 mol% MgO are provided. These compositions are capable of forming a stable glass-to-metal seal possessing electrical insulating properties for use in a lithium battery. Also provided are lithium cells containing a stainless steel body and molybdenum center pin electrically insulated by means of a seal produced according to the invention.

Developing CORBA-Based Distributed Scientific Applications From Legacy Fortran Programs

NASA Technical Reports Server (NTRS)

Sang, Janche; Kim, Chan; Lopez, Isaac

2000-01-01

An efficient methodology is presented for integrating legacy applications written in Fortran into a distributed object framework. Issues and strategies regarding the conversion and decomposition of Fortran codes into Common Object Request Broker Architecture (CORBA) objects are discussed. Fortran codes are modified as little as possible as they are decomposed into modules and wrapped as objects. A new conversion tool takes the Fortran application as input and generates the C/C++ header file and Interface Definition Language (IDL) file. In addition, the performance of the client server computing is evaluated.

Development and test of photon-counting microchannel plate detector arrays for use on space telescopes

NASA Technical Reports Server (NTRS)

Timothy, J. G.

1976-01-01

The full sensitivity, dynamic range, and photometric stability of microchannel array plates(MCP) are incorporated into a photon-counting detection system for space operations. Components of the system include feedback-free MCP's for high gain and saturated output pulse-height distribution with a stable response; multi-anode readout arrays mounted in proximity focus with the output face of the MCP; and multi-layer ceramic headers to provide electrical interface between the anode array in a sealed detector tube and the associated electronics.

The covert channel over HTTP protocol

NASA Astrophysics Data System (ADS)

Graniszewski, Waldemar; Krupski, Jacek; Szczypiorski, Krzysztof

2016-09-01

The paper presents a new steganographic method - the covert channel is created over HTTP protocol header, i.e. trailer field. HTTP protocol is one of the most frequently used in the Internet. The popularity of the Web servers and network traffic from, and to them, is one of the requirements for undetectable message exchange. To study this kind of the information hiding technique an application in Javascript language based on the Node.js framework was written. The results of the experiment that was performed to send a message in the covert channel are also presented.

Probabilistic Characterization of Adversary Behavior in Cyber Security

DOE Office of Scientific and Technical Information (OSTI.GOV)

Meyers, C A; Powers, S S; Faissol, D M

2009-10-08

The objective of this SMS effort is to provide a probabilistic characterization of adversary behavior in cyber security. This includes both quantitative (data analysis) and qualitative (literature review) components. A set of real LLNL email data was obtained for this study, consisting of several years worth of unfiltered traffic sent to a selection of addresses at ciac.org. The email data was subjected to three interrelated analyses: a textual study of the header data and subject matter, an examination of threats present in message attachments, and a characterization of the maliciousness of embedded URLs.

Digital image envelope: method and evaluation

NASA Astrophysics Data System (ADS)

Huang, H. K.; Cao, Fei; Zhou, Michael Z.; Mogel, Greg T.; Liu, Brent J.; Zhou, Xiaoqiang

2003-05-01

Health data security, characterized in terms of data privacy, authenticity, and integrity, is a vital issue when digital images and other patient information are transmitted through public networks in telehealth applications such as teleradiology. Mandates for ensuring health data security have been extensively discussed (for example The Health Insurance Portability and Accountability Act, HIPAA) and health informatics guidelines (such as the DICOM standard) are beginning to focus on issues of data continue to be published by organizing bodies in healthcare; however, there has not been a systematic method developed to ensure data security in medical imaging Because data privacy and authenticity are often managed primarily with firewall and password protection, we have focused our research and development on data integrity. We have developed a systematic method of ensuring medical image data integrity across public networks using the concept of the digital envelope. When a medical image is generated regardless of the modality, three processes are performed: the image signature is obtained, the DICOM image header is encrypted, and a digital envelope is formed by combining the signature and the encrypted header. The envelope is encrypted and embedded in the original image. This assures the security of both the image and the patient ID. The embedded image is encrypted again and transmitted across the network. The reverse process is performed at the receiving site. The result is two digital signatures, one from the original image before transmission, and second from the image after transmission. If the signatures are identical, there has been no alteration of the image. This paper concentrates in the method and evaluation of the digital image envelope.

A direct CO2 control system for ocean acidification experiments: testing effects on the coralline red algae Phymatolithon lusitanicum.

PubMed

Sordo, Laura; Santos, Rui; Reis, Joao; Shulika, Alona; Silva, Joao

2016-01-01

Most ocean acidification (OA) experimental systems rely on pH as an indirect way to control CO 2 . However, accurate pH measurements are difficult to obtain and shifts in temperature and/or salinity alter the relationship between pH and p CO 2 . Here we describe a system in which the target p CO 2 is controlled via direct analysis of p CO 2 in seawater. This direct type of control accommodates potential temperature and salinity shifts, as the target variable is directly measured instead of being estimated. Water in a header tank is permanently re-circulated through an air-water equilibrator. The equilibrated air is then routed to an infrared gas analyzer (IRGA) that measures p CO 2 and conveys this value to a Proportional-Integral-Derivative (PID) controller. The controller commands a solenoid valve that opens and closes the CO 2 flush that is bubbled into the header tank. This low-cost control system allows the maintenance of stabilized levels of p CO 2 for extended periods of time ensuring accurate experimental conditions. This system was used to study the long term effect of OA on the coralline red algae Phymatolithon lusitanicum . We found that after 11 months of high CO 2 exposure, photosynthesis increased with CO 2 as opposed to respiration, which was positively affected by temperature. Results showed that this system is adequate to run long-term OA experiments and can be easily adapted to test other relevant variables simultaneously with CO 2 , such as temperature, irradiance and nutrients.

A direct CO2 control system for ocean acidification experiments: testing effects on the coralline red algae Phymatolithon lusitanicum

PubMed Central

Santos, Rui; Reis, Joao; Shulika, Alona

2016-01-01

Most ocean acidification (OA) experimental systems rely on pH as an indirect way to control CO2. However, accurate pH measurements are difficult to obtain and shifts in temperature and/or salinity alter the relationship between pH and pCO2. Here we describe a system in which the target pCO2 is controlled via direct analysis of pCO2 in seawater. This direct type of control accommodates potential temperature and salinity shifts, as the target variable is directly measured instead of being estimated. Water in a header tank is permanently re-circulated through an air-water equilibrator. The equilibrated air is then routed to an infrared gas analyzer (IRGA) that measures pCO2 and conveys this value to a Proportional-Integral-Derivative (PID) controller. The controller commands a solenoid valve that opens and closes the CO2 flush that is bubbled into the header tank. This low-cost control system allows the maintenance of stabilized levels of pCO2 for extended periods of time ensuring accurate experimental conditions. This system was used to study the long term effect of OA on the coralline red algae Phymatolithon lusitanicum. We found that after 11 months of high CO2 exposure, photosynthesis increased with CO2 as opposed to respiration, which was positively affected by temperature. Results showed that this system is adequate to run long-term OA experiments and can be easily adapted to test other relevant variables simultaneously with CO2, such as temperature, irradiance and nutrients. PMID:27703853

WFC3/UVIS Updated 2017 Chip-Dependent Inverse Sensitivity Values

NASA Astrophysics Data System (ADS)

Deustua, S. E.; Mack, J.; Bajaj, V.; Khandrika, H.

2017-06-01

We present chip-dependent inverse sensitivity values recomputed for the 42 full frame filters based on the analysis of standard star observations with the WFC3/UVIS imager obtained between 2009 and 2015. Chip-dependent inverse sensitivities reported in the image header are now for the 'infinite' aperture, which is defined to have a radius of 6 arcseconds (151 pixels), and supercede the 2016 photometry header keyword values (PHOTFLAM, PHTFLAM1, PHTFLAM2), which correspond to a 0.3962 arcsecond (10 pixel) aperture. These new values are implemented in the June 2017 IMPHTTAB delivery and are concordant with the current synthetic photometry tables in the reference file database (CRDS). Since approximately 90% of the light is enclosed within 10 pixels, the new keyword values are 10% smaller. We also compute inverse sensitivities for an aperture with radius of 0.3962 arcseconds. Compared to the 2016 implementation, these new inverse sensitivity values differ by less than 0.5%, on average, for the same aperture. Values for the filters F200LP, F350LP, F600LP and F487N changed by more than 1% for UVIS1. UVIS2 values that changed by more than 1% are for the filters F350LP, F600LP, F850LP, F487N, and F814W. The 2017 VEGAmag zeropoint values in the UV change by up to 0.1 mag compared to 2016 and are calculated using the CALPSEC STIS spectrum for Vega. In 2016, the zeropoints were calculated with the CALSPEC Vega model.

Automatically inserted technical details improve radiology report accuracy.

PubMed

Abujudeh, Hani H; Govindan, Siddharth; Narin, Ozden; Johnson, Jamlik Omari; Thrall, James H; Rosenthal, Daniel I

2011-09-01

To assess the effect of automatically inserted technical details on the concordance of a radiology report header with the actual procedure performed. The study was IRB approved and informed consent was waived. We obtained radiology report audit data from the hospital's compliance office from the period of January 2005 through December 2009 spanning a total of 20 financial quarters. A "discordance percentage" was defined as the percentage of total studies in which a procedure code change was made during auditing. Using Chi-square analysis we compared discordance percentages between reports with manually inserted technical details (MITD) and automatically inserted technical details (AITD). The second quarter data of 2007 was not included in the analysis as the switch from MITD to AITD occurred during this quarter. The hospital's compliance office audited 9,110 studies from 2005-2009. Excluding the 564 studies in the second quarter of 2007, we analyzed a total of 8,546 studies, 3,948 with MITD and 4,598 with AITD. The discordance percentage in the MITD group was 3.95% (156/3,948, range per quarter, 1.5- 6.1%). The AITD discordance percentage was 1.37% (63/4,598, range per quarter, 0.0-2.6%). A Chi-square analysis determined a statistically significant difference between the 2 groups (P < 0.001). There was a statistically significant improvement in the concordance of a radiology report header with the performed procedure using automatically inserted technical details compared to manually inserted details. Copyright © 2011 American College of Radiology. Published by Elsevier Inc. All rights reserved.

Using a data entry clerk to improve data quality in primary care electronic medical records: a pilot study.

PubMed

Greiver, Michelle; Barnsley, Jan; Aliarzadeh, Babak; Krueger, Paul; Moineddin, Rahim; Butt, Debra A; Dolabchian, Edita; Jaakkimainen, Liisa; Keshavjee, Karim; White, David; Kaplan, David

2011-01-01

The quality of electronic medical record (EMR) data is known to be problematic; research on improving these data is needed. The primary objective was to explore the impact of using a data entry clerk to improve data quality in primary care EMRs. The secondary objective was to evaluate the feasibility of implementing this intervention. We used a before and after design for this pilot study. The participants were 13 community based family physicians and four allied health professionals in Toronto, Canada. Using queries programmed by a data manager, a data clerk was tasked with re-entering EMR information as coded or structured data for chronic obstructive pulmonary disease (COPD), smoking, specialist designations and interprofessional encounter headers. We measured data quality before and three to six months after the intervention. We evaluated feasibility by measuring acceptability to clinicians and workload for the clerk. After the intervention, coded COPD entries increased by 38% (P = 0.0001, 95% CI 23 to 51%); identifiable data on smoking categories increased by 27% (P = 0.0001, 95% CI 26 to 29%); referrals with specialist designations increased by 20% (P = 0.0001, 95% CI 16 to 22%); and identifiable interprofessional headers increased by 10% (P = 0.45, 95 CI -3 to 23%). Overall, the intervention was rated as being at least moderately useful and moderately usable. The data entry clerk spent 127 hours restructuring data for 11 729 patients. Utilising a data manager for queries and a data clerk to re-enter data led to improvements in EMR data quality. Clinicians found this approach to be acceptable.

Single-Frame Terrain Mapping Software for Robotic Vehicles

NASA Technical Reports Server (NTRS)

Rankin, Arturo L.

2011-01-01

This software is a component in an unmanned ground vehicle (UGV) perception system that builds compact, single-frame terrain maps for distribution to other systems, such as a world model or an operator control unit, over a local area network (LAN). Each cell in the map encodes an elevation value, terrain classification, object classification, terrain traversability, terrain roughness, and a confidence value into four bytes of memory. The input to this software component is a range image (from a lidar or stereo vision system), and optionally a terrain classification image and an object classification image, both registered to the range image. The single-frame terrain map generates estimates of the support surface elevation, ground cover elevation, and minimum canopy elevation; generates terrain traversability cost; detects low overhangs and high-density obstacles; and can perform geometry-based terrain classification (ground, ground cover, unknown). A new origin is automatically selected for each single-frame terrain map in global coordinates such that it coincides with the corner of a world map cell. That way, single-frame terrain maps correctly line up with the world map, facilitating the merging of map data into the world map. Instead of using 32 bits to store the floating-point elevation for a map cell, the vehicle elevation is assigned to the map origin elevation and reports the change in elevation (from the origin elevation) in terms of the number of discrete steps. The single-frame terrain map elevation resolution is 2 cm. At that resolution, terrain elevation from 20.5 to 20.5 m (with respect to the vehicle's elevation) is encoded into 11 bits. For each four-byte map cell, bits are assigned to encode elevation, terrain roughness, terrain classification, object classification, terrain traversability cost, and a confidence value. The vehicle s current position and orientation, the map origin, and the map cell resolution are all included in a header for each map. The map is compressed into a vector prior to delivery to another system.

Improving Seismic Data Accessibility and Performance Using HDF Containers

NASA Astrophysics Data System (ADS)

Evans, B. J. K.; Wang, J.; Yang, R.

2017-12-01

The performance of computational geophysical data processing and forward modelling relies on both computational and data. Significant efforts on developing new data formats and libraries have been made the community, such as IRIS/PASSCAL and ASDF in data, and programs and utilities such as ObsPy and SPECFEM. The National Computational Infrastructure hosts a national significant geophysical data collection that is co-located with a high performance computing facility and provides an opportunity to investigate how to improve the data formats from both a data management and a performance point of view. This paper investigates how to enhance the data usability in several perspectives: 1) propose a convention for the seismic (both active and passive) community to improve the data accessibility and interoperability; 2) recommend the convention used in the HDF container when data is made available in PH5 or ASDF formats; 3) provide tools to convert between various seismic data formats; 4) provide performance benchmark cases using ObsPy library and SPECFEM3D to demonstrate how different data organization in terms of chunking size and compression impact on the performance by comparing new data formats, such as PH5 and ASDF to traditional formats such as SEGY, SEED, SAC, etc. In this work we apply our knowledge and experience on data standards and conventions, such as CF and ACDD from the climate community to the seismology community. The generic global attributes widely used in climate community are combined with the existing convention in the seismology community, such as CMT and QuakeML, StationXML, SEGY header convention. We also extend such convention by including the provenance and benchmarking records so that the r user can learn the footprint of the data together with its baseline performance. In practise we convert the example wide angle reflection seismic data from SEGY to PH5 or ASDF by using ObsPy and pyasdf libraries. It quantitatively demonstrates how the accessibility can be improved if the seismic data are stored in the HDF container.

NASA Tech Briefs, October 2010

NASA Technical Reports Server (NTRS)

2010-01-01

Topics covered include: Hybrid Architecture Active Wavefront Sensing and Control; Carbon-Nanotube-Based Chemical Gas Sensor; Aerogel-Positronium Technology for the Detection of Small Quantities of Organic and/or Toxic Materials; Graphene-Based Reversible Nano-Switch/Sensor Schottky Diode; Inductive Non-Contact Position Sensor; High-Temperature Surface-Acoustic-Wave Transducer; Grid-Sphere Electrodes for Contact with Ionospheric Plasma; Enabling IP Header Compression in COTS Routers via Frame Relay on a Simplex Link; Ka-Band SiGe Receiver Front-End MMIC for Transponder Applications; Robust Optimization Design Algorithm for High-Frequency TWTs; Optimal and Local Connectivity Between Neuron and Synapse Array in the Quantum Dot/Silicon Brain; Method and Circuit for In-Situ Health Monitoring of Solar Cells in Space; BGen: A UML Behavior Network Generator Tool; Platform for Post-Processing Waveform-Based NDE; Electrochemical Hydrogen Peroxide Generator; Fabrication of Single, Vertically Aligned Carbon Nanotubes in 3D Nanoscale Architectures; Process to Create High-Fidelity Lunar Dust Simulants; Lithium-Ion Electrolytes Containing Phosphorous-Based, Flame-Retardant Additives; InGaP Heterojunction Barrier Solar Cells; Straight-Pore Microfilter with Efficient Regeneration; Determining Shear Stress Distribution in a Laminate; Self-Adjusting Liquid Injectors for Combustors; Handling Qualities Prediction of an F-16XL-Based Reduced Sonic Boom Aircraft; Tele-Robotic ATHLETE Controller for Kinematics - TRACK; Three-Wheel Brush-Wheel Sampler; Heterodyne Interferometer Angle Metrology; Aligning Astronomical Telescopes via Identification of Stars; Generation of Optical Combs in a WGM Resonator from a Bichromatic Pump; Large-Format AlGaN PIN Photodiode Arrays for UV Images; Fiber-Coupled Planar Light-Wave Circuit for Seed Laser Control in High Spectral Resolution Lidar Systems; On Calculating the Zero-Gravity Surface Figure of a Mirror; Optical Modification of Casimir Forces for Improved Function of Micro- and Nano-Scale Devices; Analysis, Simulation, and Verification of Knowledge-Based, Rule-Based, and Expert Systems; Core and Off-Core Processes in Systems Engineering; Digital Reconstruction Supporting Investigation of Mishaps; and Template Matching Approach to Signal Prediction.

Effects of Type 2 Diabetes Mellitus in Patients on Treatment With Glibenclamide and Metformin on Carvedilol Enantiomers Metabolism.

PubMed

Nardotto, Glauco H B; Coelho, Eduardo B; Paiva, Carlos E; Lanchote, Vera L

2017-06-01

Carvedilol is available in clinical practice as a racemate in which (S)-(-)-carvedilol is a β- and α 1 -adrenergic antagonist and (R)-(+)-carvedilol is only an α 1 -adrenergic antagonist. Carvedilol is mainly metabolized by glucuronidation, by CYP2D6 to hydroxyphenylcarvedilol (OHC), and by CYP2C9 to O-desmethylcarvedilol (DMC). This study evaluated the pharmacokinetics of carvedilol enantiomers and their metabolites OHC and DMC in healthy volunteers (n = 13) and in type 2 diabetes mellitus patients with good glycemic control (n = 13). The healthy subjects were enrolled to receive either a 25-mg oral single dose of carvedilol alone (no DDI) or carvedilol simultaneously with 5 mg glibenclamide and 500 mg metformin (DDI), whereas type 2 diabetes mellitus patients who were on long-term treatment with glibenclamide (5 mg/8 h) and metformin (500 mg/8 h) were enrolled to receive only a single oral dose of 25 mg carvedilol. The plasma concentrations of the (R)-(+)-carvedilol, (R)-(+)-DMC, and (R)-(+)-OHC were higher than those of (S)-(-)-carvedilol, (S)-(-)-DMC, and (S)-(-)-OHC in all investigated groups. The pharmacokinetics of the carvedilol enantiomers did not differ between the groups. However, the AUC values of the DMC enantiomers were lower in the type 2 diabetes mellitus patients than in the healthy volunteers (DDI and no DDI) [(R)-(+), 6.9, 10.4, 11.9 ng·h/mL; and (S)-(-), 2.4, 4.3, 4.0 ng·h/mL, respectively]. In contrast, the AUC values of the OHC enantiomers were higher in the type 2 diabetes mellitus patients [(R)-(+), 13.9, 6.6, 4.9 ng·h/mL; and (S)-(-), 7.2, 1.5, 1.5 ng·h/mL], which explains the fact that the carvedilol pharmacokinetics was unchanged. © 2017, The American College of Clinical Pharmacology.

Archive of digital boomer subbottom data collected during USGS cruise 05FGS01 offshore east-central Florida, July 17-29, 2005

USGS Publications Warehouse

Forde, Arnell S.; Dadisman, Shawn V.; Wiese, Dana S.; Phelps, Daniel C.

2012-01-01

In July of 2005, the U.S. Geological Survey (USGS), in cooperation with the Florida Geological Survey (FGS), conducted a geophysical survey of the Atlantic Ocean offshore of Florida's east coast from Flagler Beach to Daytona Beach. This report serves as an archive of unprocessed digital boomer subbottom data, trackline maps, navigation files, Geographic Information System (GIS) files, Field Activity Collection System (FACS) logs and formal Federal Geographic Data Committee (FGDC) metadata. Filtered and gained (showing a relative increase in signal amplitude) digital images of the seismic profiles are also provided. Refer to the Acronyms page for expansions of acronyms and abbreviations used in this report. The USGS Saint Petersburg Coastal and Marine Science Center (SPCMSC) assigns a unique identifier to each cruise or field activity. For example, 05FGS01 tells us the data were collected in 2005 for cooperative work with the FGS and the data were collected during the first field activity for that project in that calendar year. Refer to http://walrus.wr.usgs.gov/infobank/programs/html/definition/activity.html for a detailed description of the method used to assign the field activity ID. The boomer subbottom processing system consists of an acoustic energy source that is made up of capacitors charged to a high voltage and discharged through a transducer in the water. The transducer is towed on a sled floating on the water surface and when discharged emits a short acoustic pulse, or shot, which propagates through the water column and shallow stratrigraphy below. The acoustic energy is reflected at density boundaries (such as the seafloor or sediment layers beneath the seafloor), detected by the receiver (a hydrophone streamer), and recorded by a PC-based seismic acquisition system. This process is repeated at timed intervals (for example, 0.5 s) and recorded for specific intervals of time (for example, 100 ms). In this way, a two-dimensional (2-D) vertical image of the shallow geologic structure beneath the ship track is produced. Figure 1 displays the acquisition geometry. Refer to table 1 for a summary of acquisition parameters and table 2 for trackline statistics. The archived trace data are in standard Society of Exploration Geophysicists (SEG) SEG Y format (Barry and others, 1975), except an ASCII format is used for the first 3,200 bytes of the card image header instead of the standard EBCDIC format. For a detailed description about the recorded trace headers, refer to the SEG Y Format page. The SEG Y files may be downloaded and processed with commercial or public domain software such as Seismic Unix (Cohen and Stockwell, 2005). See the How To Download SEG Y Data page for download instructions. The printable profiles provided here are GIF images that were processed and gained using SU software; refer to the Software page for links to example SU processing scripts. The processed SEG Y data were also exported to Chesapeake Technology, Inc. (CTI) SonarWeb software to produce a geospatially interactive version of the profile that allows the user to obtain a geographic location and depth from the profile for a given cursor position; this information is displayed in the status bar of the browser. Please note that clicking on the profile image switches it to "Expanded View" (a compressed image of the entire line) and cursor tracking is not available in this mode.

Shape Optimization for Navier-Stokes Equations with Algebraic Turbulence Model: Numerical Analysis and Computation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Haslinger, Jaroslav, E-mail: hasling@karlin.mff.cuni.cz; Stebel, Jan, E-mail: stebel@math.cas.cz

2011-04-15

We study the shape optimization problem for the paper machine headbox which distributes a mixture of water and wood fibers in the paper making process. The aim is to find a shape which a priori ensures the given velocity profile on the outlet part. The mathematical formulation leads to the optimal control problem in which the control variable is the shape of the domain representing the header, the state problem is represented by the generalized Navier-Stokes system with nontrivial boundary conditions. This paper deals with numerical aspects of the problem.

MCBooster: a library for fast Monte Carlo generation of phase-space decays on massively parallel platforms.

NASA Astrophysics Data System (ADS)

Alves Júnior, A. A.; Sokoloff, M. D.

2017-10-01

MCBooster is a header-only, C++11-compliant library that provides routines to generate and perform calculations on large samples of phase space Monte Carlo events. To achieve superior performance, MCBooster is capable to perform most of its calculations in parallel using CUDA- and OpenMP-enabled devices. MCBooster is built on top of the Thrust library and runs on Linux systems. This contribution summarizes the main features of MCBooster. A basic description of the user interface and some examples of applications are provided, along with measurements of performance in a variety of environments

Best Practices Case Study: David Weekley Homes - Eagle Springs and Waterhaven, Houston, TX

DOE Office of Scientific and Technical Information (OSTI.GOV)

none,

2011-04-01

Case study describing David Weekley Homes, Houston Division, has qualified more than 1,240 homes for the DOE Builders Challenge. Advanced framed 2x6 walls with open headers and two-stud corners allow more room for R-20 damp sprayed cellulose wall cavity insulation that is covered with R-5 rigid XPS foam. A radiant barrier cuts heat gain in the R-38 insulated vented attics. Draft stopping at fireplace and duct chases and behind tubs, gluing sheetrock to framing, and extensive caulking make for air-tight homes at 3.0 ACH50.

Ion-exchange hollow fibers

NASA Technical Reports Server (NTRS)

Rembaum, A.; Yen, S. P. S.; Klein, E. (Inventor)

1976-01-01

An ion-exchange hollow fiber is prepared by introducing into the wall of the fiber polymerizable liquid monomers, and polymerizing the monomers therein to form solid, insoluble, crosslinked, ion-exchange resin particles which embed in the wall of the fiber. Excess particles blocking the central passage or bore of the fiber are removed by forcing liquid through the fiber. The fibers have high ion-exchange capacity, a practical wall permeability and good mechanical strength even with very thin wall dimensions. Experimental investigation of bundles of ion-exchange hollow fibers attached to a header assembly have shown the fiber to be very efficient in removing counterions from solution.

SODIUM DEUTERIUM REACTOR

DOEpatents

Oppenheimer, E.D.; Weisberg, R.A.

1963-02-26

This patent relates to a barrier system for a sodium heavy water reactor capable of insuring absolute separation of the metal and water. Relatively cold D/sub 2/O moderator and reflector is contained in a calandria into which is immersed the fuel containing tubes. The fuel elements are cooled by the sodium which flows within the tubes and surrounds the fuel elements. The fuel containing tubes are surrounded by concentric barrier tubes forming annular spaces through which pass inert gases at substantially atmospheric pressure. Header rooms above and below the calandria are provided for supplying and withdrawing the sodium and inert gases in the calandria region. (AEC)

SpecDB: The AAVSO’s Public Repository for Spectra of Variable Stars

NASA Astrophysics Data System (ADS)

Kafka, Stella; Weaver, John; Silvis, George; Beck, Sara

2018-01-01

SpecDB is the American Association of Variable Star Observers (AAVSO) spectral database. Accessible to any astronomer with the capability to perform spectroscopy, SpecDB provides an unprecedented scientific opportunity for amateur and professional astronomers around the globe. Backed by the Variable Star Index, one of the most utilized variable star catalogs, SpecDB is expected to become one of the world leading databases of its kind. Once verified by a team of expert spectroscopists, an observer can upload spectra of variable stars target easily and efficiently. Uploaded spectra can then be searched for, previewed, and downloaded for inclusion in publications. Close community development and involvement will ensure a user-friendly and versatile database, compatible with the needs of 21st century astrophysics. Observations of 1D spectra are submitted as FITS files. All spectra are required to be preprocessed for wavelength calibration and dark subtraction; Bias and flat are strongly recommended. First time observers are required to submit a spectrum of a standard (non-variable) star to be checked for errors in technique or equipment. Regardless of user validation, FITS headers must include several value cards detailing the observation, as well as information regarding the observer, equipment, and observing site in accordance with existing AAVSO records. This enforces consistency and provides necessary details for follow up analysis. Requirements are provided to users in a comprehensive guidebook and accompanying technical manual. Upon submission, FITS headers are automatically checked for errors and any anomalies are immediately fed back to the user. Successful candidates can then submit at will, including multiple simultaneous submissions. All published observations can be searched and interactively previewed. Community involvement will be enhanced by an associated forum where users can discuss observation techniques and suggest improvements to the database.

miniSEED: The Backbone Data Format for Seismological Time Series

NASA Astrophysics Data System (ADS)

Ahern, T. K.; Benson, R. B.; Trabant, C. M.

2017-12-01

In 1987, the International Federation of Digital Seismograph Networks (FDSN), adopted the Standard for the Exchange of Earthquake Data (SEED) format to be used for data archiving and exchange of seismological time series data. Since that time, the format has evolved to accommodate new capabilities and features. For example, a notable change in 1992 allowed the format, which includes both the comprehensive metadata and the time series samples, to be used in two additional forms: a container for metadata only called "dataless SEED", and 2) a stand-alone structure for time series called "miniSEED". While specifically designed for seismological data and related metadata, this format has proven to be a useful format for a wide variety of geophysical time series data. Many FDSN data centers now store temperature, pressure, infrasound, tilt and other time series measurements in this internationally used format. Since April 2016, members of the FDSN have been in discussions to design a next generation miniSEED format to accommodate current and future needs, to further generalize the format, and to address a number of historical problems or limitations. We believe the correct approach is to simplify the header, allow for arbitrary header additions, expand the current identifiers, and allow for anticipated future identifiers which are currently unknown. We also believe the primary goal of the format is for efficient archiving, selection and exchange of time series data. By focusing on these goals we avoid trying to generalize the format too broadly into specialized areas such as efficient, low-latency delivery, or including unbounded non-time series data. Our presentation will provide an overview of this format and highlight its most valuable characteristics for time series data from any geophysical domain or beyond.

Distributed Denial of Service Attack Source Detection Using Efficient Traceback Technique (ETT) in Cloud-Assisted Healthcare Environment.

PubMed

Latif, Rabia; Abbas, Haider; Latif, Seemab; Masood, Ashraf

2016-07-01

Security and privacy are the first and foremost concerns that should be given special attention when dealing with Wireless Body Area Networks (WBANs). As WBAN sensors operate in an unattended environment and carry critical patient health information, Distributed Denial of Service (DDoS) attack is one of the major attacks in WBAN environment that not only exhausts the available resources but also influence the reliability of information being transmitted. This research work is an extension of our previous work in which a machine learning based attack detection algorithm is proposed to detect DDoS attack in WBAN environment. However, in order to avoid complexity, no consideration was given to the traceback mechanism. During traceback, the challenge lies in reconstructing the attack path leading to identify the attack source. Among existing traceback techniques, Probabilistic Packet Marking (PPM) approach is the most commonly used technique in conventional IP- based networks. However, since marking probability assignment has significant effect on both the convergence time and performance of a scheme, it is not directly applicable in WBAN environment due to high convergence time and overhead on intermediate nodes. Therefore, in this paper we have proposed a new scheme called Efficient Traceback Technique (ETT) based on Dynamic Probability Packet Marking (DPPM) approach and uses MAC header in place of IP header. Instead of using fixed marking probability, the proposed scheme uses variable marking probability based on the number of hops travelled by a packet to reach the target node. Finally, path reconstruction algorithms are proposed to traceback an attacker. Evaluation and simulation results indicate that the proposed solution outperforms fixed PPM in terms of convergence time and computational overhead on nodes.

QTLTableMiner++: semantic mining of QTL tables in scientific articles.

PubMed

Singh, Gurnoor; Kuzniar, Arnold; van Mulligen, Erik M; Gavai, Anand; Bachem, Christian W; Visser, Richard G F; Finkers, Richard

2018-05-25

A quantitative trait locus (QTL) is a genomic region that correlates with a phenotype. Most of the experimental information about QTL mapping studies is described in tables of scientific publications. Traditional text mining techniques aim to extract information from unstructured text rather than from tables. We present QTLTableMiner ++ (QTM), a table mining tool that extracts and semantically annotates QTL information buried in (heterogeneous) tables of plant science literature. QTM is a command line tool written in the Java programming language. This tool takes scientific articles from the Europe PMC repository as input, extracts QTL tables using keyword matching and ontology-based concept identification. The tables are further normalized using rules derived from table properties such as captions, column headers and table footers. Furthermore, table columns are classified into three categories namely column descriptors, properties and values based on column headers and data types of cell entries. Abbreviations found in the tables are expanded using the Schwartz and Hearst algorithm. Finally, the content of QTL tables is semantically enriched with domain-specific ontologies (e.g. Crop Ontology, Plant Ontology and Trait Ontology) using the Apache Solr search platform and the results are stored in a relational database and a text file. The performance of the QTM tool was assessed by precision and recall based on the information retrieved from two manually annotated corpora of open access articles, i.e. QTL mapping studies in tomato (Solanum lycopersicum) and in potato (S. tuberosum). In summary, QTM detected QTL statements in tomato with 74.53% precision and 92.56% recall and in potato with 82.82% precision and 98.94% recall. QTM is a unique tool that aids in providing QTL information in machine-readable and semantically interoperable formats.

BOREAS RSS-14 Level-1a GOES-8 Visible, IR and Water Vapor Images

NASA Technical Reports Server (NTRS)

Hall, Forrest G. (Editor); Newcomer, Jeffrey A.; Faysash, David; Cooper, Harry J.; Smith, Eric A.

2000-01-01

The BOREAS RSS-14 team collected and processed several GOES-7 and GOES-8 image data sets that covered the BOREAS study region. The level-1a GOES-8 images were created by BORIS personnel from the level-1 images delivered by FSU personnel. The data cover 14-Jul-1995 to 21-Sep-1995 and 12-Feb-1996 to 03-Oct-1996. The data start out as three bands with 8-bit pixel values and end up as five bands with 10-bit pixel values. No major problems with the data have been identified. The differences between the level-1 and level-1a GOES-8 data are the formatting and packaging of the data. The images missing from the temporal series of level-1 GOES-8 images were zero-filled by BORIS staff to create files consistent in size and format. In addition, BORIS staff packaged all the images of a given type from a given day into a single file, removed the header information from the individual level-1 files, and placed it into a single descriptive ASCII header file. The data are contained in binary image format files. Due to the large size of the images, the level-1a GOES-8 data are not contained on the BOREAS CD-ROM set. An inventory listing file is supplied on the CD-ROM to inform users of what data were collected. The level-1a GOES-8 image data are available from the Earth Observing System Data and Information System (EOSDIS) Oak Ridge National Laboratory (ORNL) Distributed Active Archive Center (DAAC). See sections 15 and 16 for more information. The data files are available on a CD-ROM (see document number 20010000884).

A low cost igniter utilizing an SCB and titanium sub-hydride potassium perchlorate pyrotechnic

NASA Technical Reports Server (NTRS)

Bickes, R. W., Jr.; Grubelich, M. C.; Hartman, J. K.; McCampbell, C. B.; Churchill, J. K.

1994-01-01

A conventional NSI (NASA Standard Initiator) normally employs a hot-wire ignition element to ignite ZPP (zirconium potassium perchlorate). With minor modifications to the interior of a header similar to an NSI device to accommodate an SCB (semiconductor bridge), a low cost initiator was obtained. In addition, the ZPP was replaced with THKP (titanium sub-hydride potassium perchlorate) to obtain increased overall gas production and reduced static-charge sensitivity. This paper reports on the all-fire and no-fire levels obtained and on a dual mix device that uses THKP as the igniter mix and a thermite as the output mix.

FGGE/ERBM tape specification and shipping letter description

NASA Technical Reports Server (NTRS)

Han, D.; Lo, H.

1983-01-01

The Nimbus-7 FGGE/ERBM tape contains 27 ERB parameters which are extracted and reformatted from the Nimbus-7 ERB-MATRIX tape. There are four types of files on a FGGE/ERBM tape: a test file; tape-header file which describes the data set characteristics and the contents of the tape; a grid-descriptor file which contains the information of the ERB scanning channel target number and their associated latitude limits and longitude intervals; and one or more data files. A single end-of-file (EOF) tape mark is written after each file, and two EOF marks are written after the last data file on the tape.

VizieR Online Data Catalog: GTC spectra of z~2.3 quasars (Sulentic+, 2014)

NASA Astrophysics Data System (ADS)

Sulentic, J. W.; Marziani, P.; Del Olmo, A.; Dultzin, D.; Perea, J.; Negrete, C. A.

2014-09-01

Spectroscopic data for 22 intermediate redshift quasars are identified in Table 1. Actual data files are in FITS format in the spectra sub-directory. Each individual spectrum cover the spectral range 360-770 nm. Units are in wavelength in Angstrom, and specific flux in erg/s/cm2/Angstrom (pW/m3) in the observed frame (i.e., before redshift correction). Full object name (OBJECT), total exposure time (EXPTIME), number of coadded individual spectra (NUM_IMAG), and observation date (DATE-OBS) are reported as records in the FITS header of each spectrum (as in Table 2 of the paper). (2 data files).

VizieR Online Data Catalog: NiI transition probability measurements (Wood+, 2014)

NASA Astrophysics Data System (ADS)

Wood, M. P.; Lawler, J. E.; Sneden, C.; Cowan, J. J.

2014-04-01

As in much of our previous branching fraction work, this NiI branching fraction study makes use of archived FTS data from both the 1.0m Fourier Transform Spectrometer (FTS) previously at the National Solar Observatory (NSO) on Kitt Peak and the Chelsea Instruments FT500 UV FTS at Lund University in Sweden. Table 1 lists the 37 FTS spectra used in our NiI branching fraction study. All NSO spectra, raw interferograms, and header files are available in the NSO electronic archives. The 80 CCD frames of spectra from commercial Ni HCD lamps of the echelle spectrograph are listed in Table 2. (6 data files).

Characteristics of the oil transport network in the South of Mexico

NASA Astrophysics Data System (ADS)

Juárez, R.; Fernández, I. Y.; Guzmán, L.

2017-01-01

We present a study of some organizational properties of the oil transport network of the Mexican oil company (PEMEX) in a region of the State of Tabasco. Particularly, the generalized centrality and the distribution of connectivities are calculated in order to evaluate some aspects of the structure of the network. We find that the connectivities (k) are characterized by a degree distribution which follows a power-law function of the form, P(k)~k -λ, with λ = 2.6. Moreover, our procedure permits to evalute the importance of lines (ducts) and nodes, which can be wells, production headers, separation batteries and petrochemical complexes.

VizieR Online Data Catalog: Faraday tomography of foreground towards IC342 (Van Eck+, 2017)

NASA Astrophysics Data System (ADS)

van Eck, C. L.; Haverkorn, M.; Alves, M. I. R.; Beck, R.; de Bruyn, A. G.; Ensslin, T.; Farnes, J. S.; Ferriere, K.; Heald, G.; Horellou, C.; Horneffer, A.; Iacobelli, M.; Jelic, V.; Marti-Vidal, I.; Mulcahy, D. D.; Reich, W.; Rottgering, H. J. A.; Scaife, A. M. M.; Schnitzeler, D. H. F. M.; Sobey, C.; Sridhar, S. S.

2016-11-01

The Faraday depth cube of the IC342 field in polarized intensity, produced from LOFAR HBA observations as part of LOFAR proposal LC0_043. The cube is approximately 5x5 degrees in size, with 4-arcmin resolution, and covers Faraday depths from -25 to +25rad/m2. The detailed specifications are given in the table and in the FITS header. Selected frames from this cubes are shown in the paper in Figures 2 through 5. An extended description of the data processing leading to this cube is included in the paper. (2 data files).

Leo Satellite Communication through a LEO Constellation using TCP/IP Over ATM

NASA Technical Reports Server (NTRS)

Foore, Lawrence R.; Konangi, Vijay K.; Wallett, Thomas M.

1999-01-01

The simulated performance characteristics for communication between a terrestrial client and a Low Earth Orbit (LEO) satellite server are presented. The client and server nodes consist of a Transmission Control Protocol /Internet Protocol (TCP/IP) over ATM configuration. The ATM cells from the client or the server are transmitted to a gateway, packaged with some header information and transferred to a commercial LEO satellite constellation. These cells are then routed through the constellation to a gateway on the globe that allows the client/server communication to take place. Unspecified Bit Rate (UBR) is specified as the quality of service (QoS). Various data rates are considered.

Taming the Viper: Software Upgrade for VFAUser and Viper

DOE Office of Scientific and Technical Information (OSTI.GOV)

DORIN,RANDALL T.; MOSER III,JOHN C.

2000-08-08

This report describes the procedure and properties of the software upgrade for the Vibration Performance Recorder. The upgrade will check the 20 memory cards for proper read/write operation. The upgrade was successfully installed and uploaded into the Viper and the field laptop. The memory checking routine must run overnight to complete the test, although the laptop need only be connected to the Viper unit until the downloading routine is finished. The routine has limited ability to recognize incomplete or corrupt header and footer files. The routine requires 400 Megabytes of free hard disk space. There is one minor technical flawmore » detailed in the conclusion.« less

ASTROPOP: ASTROnomical Polarimetry and Photometry pipeline

NASA Astrophysics Data System (ADS)

Campagnolo, Julio C. N.

2018-05-01

AstroPoP reduces almost any CCD photometry and image polarimetry data. For photometry reduction, the code performs source finding, aperture and PSF photometry, astrometry calibration using different automated and non-automated methods and automated source identification and magnitude calibration based on online and local catalogs. For polarimetry, the code resolves linear and circular Stokes parameters produced by image beam splitter or polarizer polarimeters. In addition to the modular functions, ready-to-use pipelines based in configuration files and header keys are also provided with the code. AstroPOP was initially developed to reduce the IAGPOL polarimeter data installed at Observatório Pico dos Dias (Brazil).

Ion-exchange hollow fibers

NASA Technical Reports Server (NTRS)

Rembaum, Alan (Inventor); Yen, Shiao-Ping S. (Inventor); Klein, Elias (Inventor)

1980-01-01

An ion-exchange hollow fiber is prepared by introducing into the wall of the fiber polymerizable liquid monomers, and polymerizing the monomers therein to form solid, insoluble, cross-linked, ion-exchange resin particles which embed in the wall of the fiber. Excess particles blocking the central passage or bore of the fiber are removed by forcing liquid through the fiber. The fibers have high ion-exchange capacity, a practical wall permeability and good mechanical strength even with very thin wall dimensions. Experimental investigation of bundles of ion-exchange hollow fibers attached to a header assembly have shown the fiber to be very efficient in removing counterions from solution.

Ion-exchange hollow fibers

NASA Technical Reports Server (NTRS)

Rembaum, Alan (Inventor); Yen, Shiao-Ping S. (Inventor); Klein, Elias (Inventor)

1977-01-01

An ion-exchange hollow fiber is prepared by introducing into the wall of the fiber polymerizable liquid monomers, and polymerizing the monomers therein to form solid, insoluble, cross-linked, ion-exchange resin particles which embed in the wall of the fiber. Excess particles blocking the central passage or bore of the fiber are removed by forcing liquid through the fiber. The fibers have high ion-exchange capacity, a practical wall permeability and good mechanical strength even with very thin wall dimensions. Experimental investigation of bundles of ion-exchange hollow fibers attached to a header assembly have shown the fiber to be very efficient in removing counterions from solution.

Shape Optimization for Navier-Stokes Equations with Algebraic Turbulence Model: Existence Analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bulicek, Miroslav; Haslinger, Jaroslav; Malek, Josef

2009-10-15

We study a shape optimization problem for the paper machine headbox which distributes a mixture of water and wood fibers in the paper making process. The aim is to find a shape which a priori ensures the given velocity profile on the outlet part. The mathematical formulation leads to an optimal control problem in which the control variable is the shape of the domain representing the header, the state problem is represented by a generalized stationary Navier-Stokes system with nontrivial mixed boundary conditions. In this paper we prove the existence of solutions both to the generalized Navier-Stokes system and tomore » the shape optimization problem.« less

Cargo Movement Operations System (CMOS) Requirements Traceability Matrix, Critical Design Review

DTIC Science & Technology

1990-07-16

NO [ ] COMMENT DISPOSITION: ACCEPT [ ] REJECT [ J COY1MENT STATUS: OPEN [ ] CLOSED [ ] Cmnt Page Paragraph No. No. Number Comment 1. 1-320 SS0811, The references to Advanced TCMD were J-201 CUC1209 misspelled. 2. J-193 CUlC0650 Insert a space between "DDN" and "IN". 3. J-197 CUICI050 Insert a space between "ICI" and "IN". 4. J-206 CU1C12l3 Add "or" to the end of the header. ORIGINATOR CONTROL NUMBER: RTM-0002 PROGRAM OFFICE CONTROL NUMBER: DATA ITEM DISCREPANCY WORKSHEET CDRL NUMBER: A018-04 DATE: 07/16/90

VizieR Online Data Catalog: Example of FERRE code spectra (Aguado+, 2017)

NASA Astrophysics Data System (ADS)

Aguado, D. S.; Gonzalez Hernandez, J. I.; Allende Prieto, C.; Rebolo, R.

2017-05-01

FERRE matches physical models to observed data. It was created to deal with the common problem of having numerical models that are costly to evaluate, and need to be used to interpret large data sets. ferre.pdf file contains the FERRE uses's guide. The code can be obtained from http://hebe.as.utexas.edu/ferre Example : f_crump3h.dat is a tool usable with FERRE with the parameters shown in its header: Resolving Power:10.000 3600 <= λ <= 9000Å, -6 <= [Fe/H] <=-2, -1 <= [C/Fe] <= 5, 4750 <= Tefff <= 7000, 1.0 <= logg <= 5.0, It is the grid used for the paper. (2 data files).

DICOM image quantification secondary capture (DICOM IQSC) integrated with numeric results, regions, and curves: implementation and applications in nuclear medicine

NASA Astrophysics Data System (ADS)

Cao, Xinhua; Xu, Xiaoyin; Voss, Stephan

2017-03-01

In this paper, we describe an enhanced DICOM Secondary Capture (SC) that integrates Image Quantification (IQ) results, Regions of Interest (ROIs), and Time Activity Curves (TACs) with screen shots by embedding extra medical imaging information into a standard DICOM header. A software toolkit of DICOM IQSC has been developed to implement the SC-centered information integration of quantitative analysis for routine practice of nuclear medicine. Primary experiments show that the DICOM IQSC method is simple and easy to implement seamlessly integrating post-processing workstations with PACS for archiving and retrieving IQ information. Additional DICOM IQSC applications in routine nuclear medicine and clinic research are also discussed.

Ultrasonic probe system for the bore-side inspection of tubes and welds therein

DOEpatents

Cook, K. Von; Koerner, Dan W.; Cunningham, Jr., Robert A.; Murrin, Jr., Horace T.

1977-07-26

A probe system is provided for the bore-side inspection of tube-to-header welds and the like for small diameter tubes. The probe head of the system includes an ultrasonic transmitter-receiver transducer, a separate ultrasonic receiver, a reflector associated with the transducer to properly orient the ultrasonic signal with respect to a tube wall, a baffle to isolate the receiver from the transducer, and means for maintaining the probe head against the tube wall under investigation. Since the probe head must rotate to inspect along a helical path, special ultrasonic signal connections are employed. Through the use of the probe, flaws at either the inner or outer surfaces may be detected.

Practical solutions to implementing "Born Semantic" data systems

NASA Astrophysics Data System (ADS)

Leadbetter, A.; Buck, J. J. H.; Stacey, P.

2015-12-01

The concept of data being "Born Semantic" has been proposed in recent years as a Semantic Web analogue to the idea of data being "born digital"[1], [2]. Within the "Born Semantic" concept, data are captured digitally and at a point close to the time of creation are annotated with markup terms from semantic web resources (controlled vocabularies, thesauri or ontologies). This allows heterogeneous data to be more easily ingested and amalgamated in near real-time due to the standards compliant annotation of the data. In taking the "Born Semantic" proposal from concept to operation, a number of difficulties have been encountered. For example, although there are recognised methods such as Header, Dictionary, Triples [3] for the compression, publication and dissemination of large volumes of triples these systems are not practical to deploy in the field on low-powered (both electrically and computationally) devices. Similarly, it is not practical for instruments to output fully formed semantically annotated data files if they are designed to be plugged into a modular system and the data to be centrally logged in the field as is the case on Argo floats and oceanographic gliders where internal bandwidth becomes an issue [2]. In light of these issues, this presentation will concentrate on pragmatic solutions being developed to the problem of generating Linked Data in near real-time systems. Specific examples from the European Commission SenseOCEAN project where Linked Data systems are being developed for autonomous underwater platforms, and from work being undertaken in the streaming of data from the Irish Galway Bay Cable Observatory initiative will be highlighted. Further, developments of a set of tools for the LogStash-ElasticSearch software ecosystem to allow the storing and retrieval of Linked Data will be introduced. References[1] A. Leadbetter & J. Fredericks, We have "born digital" - now what about "born semantic"?, European Geophysical Union General Assembly, 2014.[2] J. Buck & A. Leadbetter, Born semantic: linking data from sensors to users and balancing hardware limitations with data standards, European Geophysical Union General Assembly, 2015.[3] J. Fernandez et al., Binary RDF Representation for Publication and Exchange (HDT), Web Semantics 19:22-41, 2013.

Improvements in Cold-Plate Fabrication

NASA Technical Reports Server (NTRS)

Zaffetti, Mark A.; Taddey, Edmund P.; Laurin, Michael B.; Chabebe, Natalia

2012-01-01

Five improvements are reported in cold-plate fabrication. This cold plate is part of a thermal control system designed to serve on space missions. The first improvement is the merging of the end sheets of the cold plate with the face sheets of the structural honeycomb panel. The cold plate, which can be a brazed assembly, uses the honeycomb face sheet as its end sheet. Thus, when the honeycomb panel is fabricated, the face sheet that is used is already part of the cold plate. In addition to reducing weight, costs, and steps, the main benefit of this invention is that it creates a more structurally sound assembly. The second improvement involves incorporation of the header into the closure bar to pass the fluid to a lower layer. Conventional designs have used a separate header, which increases the geometry of the system. The improvement reduces the geometry, thus allowing the cold plate to fit into smaller area. The third improvement eliminates the need of hose, tube, or manifold to supply the cooling fluid externally. The external arrangement can be easily damaged and is vulnerable to leakage. The new arrangement incorporates an internal fluid transfer tube. This allows the fluid to pass from one cold plate to the other without any exposed external features. The fourth improvement eliminates separate fabrication of cold plate(s) and structural members followed by a process of attaching them to each other. Here, the structural member is made of material that can be brazed just as that of the cold plate. Now the structural member and the cold plate can be brazed at the same time, creating a monolithic unit, and thus a more structurally sound assembly. Finally, the fifth improvement is the elimination of an additional welding step that can damage the braze joints. A tube section, which is usually welded on after the braze process, is replaced with a more structurally sound configuration that can be brazed at the same time as the rest of the cold plate.

Examining the relative effectiveness of different message framing strategies for child passenger safety: recommendations for increased comprehension and compliance.

PubMed

Will, Kelli England; Decina, Lawrence E; Maple, Erin L; Perkins, Amy M

2015-06-01

Age-appropriate child restraints and rear seating dramatically reduce injury in vehicle crashes. Yet parents and caregivers struggle to comply with child passenger safety (CPS) recommendations, and frequently make mistakes when choosing and installing restraints. The purpose of this research was to evaluate various methods of framing CPS recommendations, and to examine the relative effectiveness on parents' knowledge, attitudes, and behavioral intentions related to best practices and proper use of child restraints. Emphasis framing is a persuasion technique that involves placing focus on specific aspects of the content in order to encourage or discourage certain interpretations of the content. A 5 (flyer group) X 2 (time) randomized experiment was conducted in which 300 parent participants answered a pre-survey, viewed one of four flyer versions or a no-education control version, and completed a post-survey. Surveys measured CPS knowledge, attitudes, perceptions of efficacy and risk, and behavioral intentions. The four flyers compared in this study all communicated the same CPS recommendations, but several versions were tested which each employed a different emphasis frame: (1) recommendations organized by the natural progression of seat types; (2) recommendations which focused on avoiding premature graduation; (3) recommendations which explained the risk-reduction rationale behind the information given; or (4) recommendations which were organized by age. In a fifth no-education (control) condition, participants viewed marketing materials. Analyses of covariance and pairwise comparisons indicated the risk-reduction rationale flyer outperformed other flyers for many subscales, and significantly differed from no-education control for the most subscales, including restraint selection, back seat knowledge, rear-facing knowledge and attitudes, total efficacy, overall attitudes, and stated intentions. This research provides insight for increasing caregiver understanding and compliance with CPS information. Recommendations for the field include communicating the rationale behind the information given, using behavior-based directives in headers, avoiding age-based headers, and incorporating back-seat positioning directives throughout. Copyright © 2015 Elsevier Ltd. All rights reserved.

The Keck keyword layer

NASA Technical Reports Server (NTRS)

Conrad, A. R.; Lupton, W. F.

1992-01-01

Each Keck instrument presents a consistent software view to the user interface programmer. The view consists of a small library of functions, which are identical for all instruments, and a large set of keywords, that vary from instrument to instrument. All knowledge of the underlying task structure is hidden from the application programmer by the keyword layer. Image capture software uses the same function library to collect data for the image header. Because the image capture software and the instrument control software are built on top of the same keyword layer, a given observation can be 'replayed' by extracting keyword-value pairs from the image header and passing them back to the control system. The keyword layer features non-blocking as well as blocking I/O. A non-blocking keyword write operation (such as setting a filter position) specifies a callback to be invoked when the operation is complete. A non-blocking keyword read operation specifies a callback to be invoked whenever the keyword changes state. The keyword-callback style meshes well with the widget-callback style commonly used in X window programs. The first keyword library was built for the two Keck optical instruments. More recently, keyword libraries have been developed for the infrared instruments and for telescope control. Although the underlying mechanisms used for inter-process communication by each of these systems vary widely (Lick MUSIC, Sun RPC, and direct socket I/O, respectively), a basic user interface has been written that can be used with any of these systems. Since the keyword libraries are bound to user interface programs dynamically at run time, only a single set of user interface executables is needed. For example, the same program, 'xshow', can be used to display continuously the telescope's position, the time left in an instrument's exposure, or both values simultaneously. Less generic tools that operate on specific keywords, for example an X display that controls optical instrument exposures, have also been written using the keyword layer.

Neutronic fuel element fabrication

DOEpatents

Korton, George

2004-02-24

This disclosure describes a method for metallurgically bonding a complete leak-tight enclosure to a matrix-type fuel element penetrated longitudinally by a multiplicity of coolant channels. Coolant tubes containing solid filler pins are disposed in the coolant channels. A leak-tight metal enclosure is then formed about the entire assembly of fuel matrix, coolant tubes and pins. The completely enclosed and sealed assembly is exposed to a high temperature and pressure gas environment to effect a metallurgical bond between all contacting surfaces therein. The ends of the assembly are then machined away to expose the pin ends which are chemically leached from the coolant tubes to leave the coolant tubes with internal coolant passageways. The invention described herein was made in the course of, or under, a contract with the U.S. Atomic Energy Commission. It relates generally to fuel elements for neutronic reactors and more particularly to a method for providing a leak-tight metal enclosure for a high-performance matrix-type fuel element penetrated longitudinally by a multiplicity of coolant tubes. The planned utilization of nuclear energy in high-performance, compact-propulsion and mobile power-generation systems has necessitated the development of fuel elements capable of operating at high power densities. High power densities in turn require fuel elements having high thermal conductivities and good fuel retention capabilities at high temperatures. A metal clad fuel element containing a ceramic phase of fuel intimately mixed with and bonded to a continuous refractory metal matrix has been found to satisfy the above requirements. Metal coolant tubes penetrate the matrix to afford internal cooling to the fuel element while providing positive fuel retention and containment of fission products generated within the fuel matrix. Metal header plates are bonded to the coolant tubes at each end of the fuel element and a metal cladding or can completes the fuel-matrix enclosure by encompassing the sides of the fuel element between the header plates.

VizieR Online Data Catalog: xi Tau UBV and MOST light curves (Nemravova+, 2016)

NASA Astrophysics Data System (ADS)

Nemravova, J. A.; Harmanec, P.; Broz, M.; Vokrouhlicky, D.; Mourard, D.; Hummel, C. A.; Cameron, C.; Matthews, J. M.; Bolton, C. T.; Bozic, H.; Chini, R.; Dembsky, T.; Engle, S.; Farrington, C.; Grunhut, J. H.; Guenther, D. B.; Guinan, E. F.; Korcakova, D.; Koubsky, P.; Kiek, R.; Kuschnig, R.; Mayer, P.; McCook, G. P.; Moffat, A. F. J.; Nardetto, N.; Pra, A.; Ribeiro, J.; Rowe, J.; Rucinski, S.; Skoda, P.; Slechta, M.; Tallon-Bosc, I.; Votruba, V.; Weiss, W. W.; Wolf, M.; Zasche, P.; Zavala, R. T.

2016-05-01

We present reduced observations, that were used in study of the quadruple hierarchical binary xi Tauri. The observational material consists of radial-velocity measurements (tabled1.dat), photometric measurements in the MOST filter (tabled2.dat), and Johnson's U (tabled3.dat), B (tabled4.dat), and V (tabled5.dat), and spectro-interferometric measurements represented by squared visibility moduli (tabled6.dat), and closure phases (tabled7.dat). The~description of the reductions is given in Appendices A (the spectroscopy), B (the photometry), and C (the spectro-interferometry). The procedure of radial-velocity measuring is described in Sect. 3.1. Headers of Tables D.1-D.7 published electronically are also given in Appendix D. (7 data files).

Implementation of a standard format for GPS common view data

NASA Technical Reports Server (NTRS)

Weiss, Marc A.; Thomas, Claudine

1995-01-01

A new format for standardizing common view time transfer data, recommended by the Consultative Committee for the Definition of the Second, is being implemented in receivers commonly used for contributing data for the generation of International Atomic Time. We discuss three aspects of this new format that potentially improve GPS common-view time transfer: (1) the standard specifies the method for treating short term data, (2) it presents data in consistent formats including needed terms not previously available, and (3) the standard includes a header of parameters important for the GPS common-view process. In coordination with the release of firmware conforming to this new format the Bureau International des Poids et Mesures will release future international track schedules consistent with the new standard.

Method of data communications with reduced latency

DOEpatents

Blocksome, Michael A; Parker, Jeffrey J

2013-11-05

Data communications with reduced latency, including: writing, by a producer, a descriptor and message data into at least two descriptor slots of a descriptor buffer, the descriptor buffer comprising allocated computer memory segmented into descriptor slots, each descriptor slot having a fixed size, the descriptor buffer having a header pointer that identifies a next descriptor slot to be processed by a DMA controller, the descriptor buffer having a tail pointer that identifies a descriptor slot for entry of a next descriptor in the descriptor buffer; recording, by the producer, in the descriptor a value signifying that message data has been written into descriptor slots; and setting, by the producer, in dependence upon the recorded value, a tail pointer to point to a next open descriptor slot.

Therapeutic aspects of Puerto Rican cult practices.

PubMed

Koss, J D

1975-05-01

This paper seeks to explore the phenomenon of possession trance in the ritual context from still another tack, complementary to the studies cited above, by analyzing it as an active and perhaps necessary component in the development of significant personal relationships basic to the organization and goals of some religous cults.-1 This view has been suggested by data gathered in study of social process in Puerto Rican Spiritist cults-2 which examined the relationship between patterns of cult social organization and the cult execution of a culturally patterned psychotherapeutic process for committed adherents whose emotional problems are diagnosed by cult headers as manifestations of developing "faculties" for communication with the spirit world-3 (see Koss; Rogler and Hollingshead, 1965, pp. 244-254; Seda Bonilla, 1964).

Numerical demonstration of neuromorphic computing with photonic crystal cavities.

PubMed

Laporte, Floris; Katumba, Andrew; Dambre, Joni; Bienstman, Peter

2018-04-02

We propose a new design for a passive photonic reservoir computer on a silicon photonics chip which can be used in the context of optical communication applications, and study it through detailed numerical simulations. The design consists of a photonic crystal cavity with a quarter-stadium shape, which is known to foster interesting mixing dynamics. These mixing properties turn out to be very useful for memory-dependent optical signal processing tasks, such as header recognition. The proposed, ultra-compact photonic crystal cavity exhibits a memory of up to 6 bits, while simultaneously accepting bitrates in a wide region of operation. Moreover, because of the inherent low losses in a high-Q photonic crystal cavity, the proposed design is very power efficient.

Source Header List. Volume 1. A through K

DTIC Science & Technology

1998-07-01

M 020> u~ an Wj WI j In 0 In j M4 w a W I W I xL.U (In M -1 00 WK M)~ >>2>1>1 0 MM -wan wa- WWW Z~ 0 .( MW00 I 0 MO MEM w~ 2’ 202 ZwU 2W M MMM 40 In...0OL 0 3 02 02 0 M 1 0 0 OHP - 0 0 O W 004 o00 04 01- ow 04 0<-i 0n OW 04 04 001 0 0 0x 0 0 OW Www L M L L O L2 L LC. LCD L2 LW LL.Z 0Wou L L L.U LL LL L

SETI-EC: SETI Encryption Code

NASA Astrophysics Data System (ADS)

Heller, René

2018-03-01

The SETI Encryption code, written in Python, creates a message for use in testing the decryptability of a simulated incoming interstellar message. The code uses images in a portable bit map (PBM) format, then writes the corresponding bits into the message, and finally returns both a PBM image and a text (TXT) file of the entire message. The natural constants (c, G, h) and the wavelength of the message are defined in the first few lines of the code, followed by the reading of the input files and their conversion into 757 strings of 359 bits to give one page. Each header of a page, i.e. the little-endian binary code translation of the tempo-spatial yardstick, is calculated and written on-the-fly for each page.

An extended BET format for La RC shuttle experiments: Definition and development

NASA Technical Reports Server (NTRS)

Findlay, J. T.; Kelly, G. M.; Henry, M. W.

1981-01-01

A program for shuttle post-flight data reduction is discussed. An extended Best Estimate Trajectory (BET) file was developed. The extended format results in some subtle changes to the header record. The major change is the addition of twenty-six words to each data record. These words include atmospheric related parameters, body axis rate and acceleration data, computed aerodynamic coefficients, and angular accelerations. These parameters were added to facilitate post-flight aerodynamic coefficient determinations as well as shuttle entry air data sensor analyses. Software (NEWBET) was developed to generate the extended BET file utilizing the previously defined ENTREE BET, a dynamic data file which may be either derived inertial measurement unit data or aerodynamic coefficient instrument package data, and some atmospheric information.

The behavior of compression and degradation for municipal solid waste and combined settlement calculation method.

PubMed

Shi, Jianyong; Qian, Xuede; Liu, Xiaodong; Sun, Long; Liao, Zhiqiang

2016-09-01

The total compression of municipal solid waste (MSW) consists of primary, secondary, and decomposition compressions. It is usually difficult to distinguish between the three parts of compressions. In this study, the odeometer test was used to distinguish between the primary and secondary compressions to determine the primary and secondary compression coefficient. In addition, the ending time of the primary compressions were proposed based on municipal solid waste compression tests in a degradation-inhibited condition by adding vinegar. The amount of the secondary compression occurring in the primary compression stage has a relatively high percentage to either the total compression or the total secondary compression. The relationship between the degradation ratio and time was obtained from the tests independently. Furthermore, a combined compression calculation method of municipal solid waste for all three parts of compressions including considering organics degradation is proposed based on a one-dimensional compression method. The relationship between the methane generation potential L0 of LandGEM model and degradation compression index was also discussed in the paper. A special column compression apparatus system, which can be used to simulate the whole compression process of municipal solid waste in China, was designed. According to the results obtained from 197-day column compression test, the new combined calculation method for municipal solid waste compression was analyzed. The degradation compression is the main part of the compression of MSW in the medium test period. Copyright © 2015 Elsevier Ltd. All rights reserved.

DNABIT Compress - Genome compression algorithm.

PubMed

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-22

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, "DNABIT Compress" for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that "DNABIT Compress" algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases.

On service differentiation in mobile Ad Hoc networks.

PubMed

Zhang, Shun-liang; Ye, Cheng-qing

2004-09-01

A network model is proposed to support service differentiation for mobile Ad Hoc networks by combining a fully distributed admission control approach and the DIFS based differentiation mechanism of IEEE802.11. It can provide different kinds of QoS (Quality of Service) for various applications. Admission controllers determine a committed bandwidth based on the reserved bandwidth of flows and the source utilization of networks. Packets are marked when entering into networks by markers according to the committed rate. By the mark in the packet header, intermediate nodes handle the received packets in different manners to provide applications with the QoS corresponding to the pre-negotiated profile. Extensive simulation experiments showed that the proposed mechanism can provide QoS guarantee to assured service traffic and increase the channel utilization of networks.

Erratum: "A Smaller Radius for the Transiting Exoplanet WASP-10b" (2009, ApJ, 692, L100)

NASA Astrophysics Data System (ADS)

Johnson, John Asher; Winn, Joshua N.; Cabrera, Nicole E.; Carter, Joshua A.

2010-03-01

We have identified an error in our Heliocentric Julian Dates (HJDs) of observation caused by incorrect input to the code used to convert from JD to HJD. The times in Table 1 have been corrected by adding 0.006382 day to each entry in the original Column 1. Similarly, the measured mid-transit time in Table 2 has been changed to Tc = 2454664.037295. We also note that the header in Column 1 of Table 1 is incorrect. The label should read HJD, rather than BJD. The updated Tables 1 and 2 have been included herein. This error has no impact on our main conclusions. We thank Pedro Valdes Sada and Gracjan Maciejewski for pointing out the incorrect mid-transit time.

Intelligent Sensing and Classification in DSR-Based Ad Hoc Networks

NASA Astrophysics Data System (ADS)

Dempsey, Tae; Sahin, Gokhan; Morton, Yu T. (Jade

Wireless ad hoc networks have fundamentally altered today's battlefield, with applications ranging from unmanned air vehicles to randomly deployed sensor networks. Security and vulnerabilities in wireless ad hoc networks have been considered at different layers, and many attack strategies have been proposed, including denial of service (DoS) through the intelligent jamming of the most critical packet types of flows in a network. This paper investigates the effectiveness of intelligent jamming in wireless ad hoc networks using the Dynamic Source Routing (DSR) and TCP protocols and introduces an intelligent classifier to facilitate the jamming of such networks. Assuming encrypted packet headers and contents, our classifier is based solely on the observable characteristics of size, inter-arrival timing, and direction and classifies packets with up to 99.4% accuracy in our experiments.

Passive and Active Analysis in DSR-Based Ad Hoc Networks

NASA Astrophysics Data System (ADS)

Dempsey, Tae; Sahin, Gokhan; Morton, Y. T. (Jade)

Security and vulnerabilities in wireless ad hoc networks have been considered at different layers, and many attack strategies have been proposed, including denial of service (DoS) through the intelligent jamming of the most critical packet types of flows in a network. This paper investigates the effectiveness of intelligent jamming in wireless ad hoc networks using the Dynamic Source Routing (DSR) and TCP protocols and introduces an intelligent classifier to facilitate the jamming of such networks. Assuming encrypted packet headers and contents, our classifier is based solely on the observable characteristics of size, inter-arrival timing, and direction and classifies packets with up to 99.4% accuracy in our experiments. Furthermore, we investigate active analysis, which is the combination of a classifier and intelligent jammer to invoke specific responses from a victim network.

C-Shell Cookbook

NASA Astrophysics Data System (ADS)

Currie, Malcolm J.

This cookbook describes the fundamentals of writing scripts using the UNIX C shell. It shows how to combine Starlink and private applications with shell commands and constructs to create powerful and time-saving tools for performing repetitive jobs, creating data-processing pipelines, and encapsulating useful recipes. The cookbook aims to give practical and reassuring examples to at least get you started without having to consult a UNIX manual. However, it does not offer a comprehensive description of C-shell syntax to prevent you from being overwhelmed or intimidated. The topics covered are: how to run a script, defining shell variables, prompting, arithmetic and string processing, passing information between Starlink applications, obtaining dataset attributes and FITS header information, processing multiple files and filename modification, command-line arguments and options, and loops. There is also a glossary.

Mitigation of steam generator tube rupture in a pressurized water reactor with passive safety systems

DOEpatents

McDermott, D.J.; Schrader, K.J.; Schulz, T.L.

1994-05-03

The effects of steam generator tube ruptures in a pressurized water reactor are mitigated by reducing the pressure in the primary loop by diverting reactor coolant through the heat exchanger of a passive heat removal system immersed in the in containment refueling water storage tank in response to a high feed water level in the steam generator. Reactor coolant inventory is maintained by also in response to high steam generator level introducing coolant into the primary loop from core make-up tanks at the pressure in the reactor coolant system pressurizer. The high steam generator level is also used to isolate the start-up feed water system and the chemical and volume control system to prevent flooding into the steam header. 2 figures.

VizieR Online Data Catalog: B213 filament 150 and 260GHz emission maps (Bracco+, 2017)

NASA Astrophysics Data System (ADS)

Bracco, A.; Palmeirim, P.; Andre, P.; Adam, R.; Ade, P.; Bacmann, A.; Beelen, A.; Benoeet, A.; Bideaud, A.; Billot, N.; Bourrion, O.; Calvo, M.; Catalano, A.; Coiffard, G.; Comis, B.; D'Addabbo, A.; Desert, F.-X.; Didelon, P.; Doyle, S.; Goupy, J.; Konyves, V.; Kramer, C.; Lagache, G.; Leclercq, S.; Macias-Perez, J. F.; Maury, A.; Mauskopf, P.; Mayet, F.; Monfardini, A.; Motte, F.; Pajot, F.; Pascale, E.; Peretto, N.; Perotto, L.; Pisano, G.; Ponthieu, N.; Reveret, V.; Rigby, A.; Ritacco, A.; Rodriguez, L.; Romero, C.; Roy, A.; Ruppin, F.; Schuster, K.; Sievers, A.; Triqueneaux, S.; Tucker, C.; Zylka, R.

2017-07-01

We present the continuum emission maps at 150 and 260GHz of the B213 filament in the Taurus molecular complex obtained with the NIKA camera at IRAM 30m. Observations were performed during the first NIKA open pool, in February 2014, and are presented in the paper. The maps FWHM angular resolution is 24" (see Fig. 1). Due to the scanning strategy, the noise rms is relatively constant in the central part of maps but rapidly increase towards the edge. Scales larger than 2' are filtered during the data reduction. The image coordinates can be found in the FITS header. Three maps per frequency are provided: flux density, noise, and time-per-pixel. Units are MJy/sr and second, respectively. (2 data files).

Mitigation of steam generator tube rupture in a pressurized water reactor with passive safety systems

DOEpatents

McDermott, Daniel J.; Schrader, Kenneth J.; Schulz, Terry L.

1994-01-01

The effects of steam generator tube ruptures in a pressurized water reactor are mitigated by reducing the pressure in the primary loop by diverting reactor coolant through the heat exchanger of a passive heat removal system immersed in the in containment refueling water storage tank in response to a high feed water level in the steam generator. Reactor coolant inventory is maintained by also in response to high steam generator level introducing coolant into the primary loop from core make-up tanks at the pressure in the reactor coolant system pressurizer. The high steam generator level is also used to isolate the start-up feed water system and the chemical and volume control system to prevent flooding into the steam header. 2 figures.

VizieR Online Data Catalog: HD61005 SPHERE H and Ks images (Olofsson+, 2016)

NASA Astrophysics Data System (ADS)

Olofsson, J.; Samland, M.; Avenhaus, H.; Caceres, C.; Henning, T.; Moor, A.; Milli, J.; Canovas, H.; Quanz, S. P.; Schreiber, M. R.; Augereau, J.-C.; Bayo, A.; Bazzon, A.; Beuzit, J.-L.; Boccaletti, A.; Buenzli, E.; Casassus, S.; Chauvin, G.; Dominik, C.; Desidera, S.; Feldt, M.; Gratton, R.; Janson, M.; Lagrange, A.-M.; Langlois, M.; Lannier, J.; Maire, A.-L.; Mesa, D.; Pinte, C.; Rouan, D.; Salter, G.; Thalmann, C.; Vigan, A.

2016-05-01

The fits files contains the reduced ADI and DPI SPHERE observations used to produce Fig. 1 of the paper. Besides the primary card, the files consists of 6 additional ImageHDU. The first and second one contain the SPHERE IRDIS ADI H band observations and the noise map. The third and fourth contain the SPHERE IRDIS ADI Ks band observations and the corresponding noise map. Finally, the fifth and sixth ImageHDU contain the SPHERE IRDIS DPI H band data as well as the noise map. Each ADI image has 1024x1024 pixels, while the DPI images have 1800x1800 pixels. The header of the primary card contains the pixel sizes for each datasets and the wavelengths of the H and K band observations. (2 data files).

Coding considerations for standalone molecular dynamics simulations of atomistic structures

NASA Astrophysics Data System (ADS)

Ocaya, R. O.; Terblans, J. J.

2017-10-01

The laws of Newtonian mechanics allow ab-initio molecular dynamics to model and simulate particle trajectories in material science by defining a differentiable potential function. This paper discusses some considerations for the coding of ab-initio programs for simulation on a standalone computer and illustrates the approach by C language codes in the context of embedded metallic atoms in the face-centred cubic structure. The algorithms use velocity-time integration to determine particle parameter evolution for up to several thousands of particles in a thermodynamical ensemble. Such functions are reusable and can be placed in a redistributable header library file. While there are both commercial and free packages available, their heuristic nature prevents dissection. In addition, developing own codes has the obvious advantage of teaching techniques applicable to new problems.

VizieR Online Data Catalog: NIBLES. I. The Nancay HI survey (van Driel+, 2016)

NASA Astrophysics Data System (ADS)

van Driel, M.; Butcher, Z.; Schneider, S.; Lehnert, M.; Minchin, R.; Blyth, S.-L.; Chemin, L.; Hallet, N.; Joseph, T.; Kotze, P.; Kraan-Korteweg, R. C.; Olofsson, H.; Ramatsoku, M.

2016-11-01

HI 21cm line spectra of the 1870 clearly or marginally detected SDSS sources obtained for NIBLES at the Nancay Radio Telescope. Please note that these include the six detections with velocities below the 900 km/s lower limit for the NIBLES statistical sample, which are listed in Table A.5 (NIBLES sources 0347, 1572, 1734, 1897, 2259, and 2326). See Sect. 3 of the paper for further details on data acquisition and reduction. Data have been smoothed in velocity to 18 km/s resolution (see exact number in the spectrum headers). A fitted polynomial baseline was substracted from the observed spectra. Velocities (first column) are heliocentric in the optical convention in units of km/s and flux densities (second column) are in Janskys. (4 data files).

A Study of the Ethernet Troughput Performance of the Embedded System

NASA Astrophysics Data System (ADS)

Duan, Zhi-Yu; Zhao, Zhao-Wang

2007-09-01

An ethernet acceleration solution developed for the NIOS II Embedded System in astronomical applications - Mason Express is introduced in this paper. By manually constructing the proper network protocol headers and directly driving the hardware, Mason Express goes around the performance bottleneck of the Light Weighted IP stack (LWIP), and achieves up to 90Mb/s unidirectional data troughput rate from the embedded system board to the data collecting computer. With the LWIP stack, the maximum data rate is about 10.57Mb/s. Mason Express is a total software solution and no hardware changes required, neither does it affect the uCOS II operating system nor the LWIP stack, and can be implemented with or without any embedded operating system. It maximally protects the intelligence investment of the users.

Development of potassium ion conducting hollow glass fibers. [potassium sulfur battery

NASA Technical Reports Server (NTRS)

Tsang, F. Y.

1974-01-01

Potassium ion conducting glasses, chemically resistant to potassium, potassium sulfide and sulfur, were made and their possible utility as the membrane material for a potassium/sulfur battery was evaluated. At least one satisfactory candidate was found. It possesses an electrical resistance which makes it usable as a membrane in the form of a fine hollow fiber. It's chemical and electrochemical resistances are excellent. The other aspects of the possible potassium sulfur battery utilizing such fine hollow fibers, including the header (or tube sheet) and a cathode current collector were studied. Several cathode materials were found to be satisfactory. None of the tube sheet materials studied possessed all the desired properties. Multi-fiber cells had very limited life-time due to physical failure of fibers at the fiber/tube sheet junctions.

Graphics processing unit-assisted lossless decompression

DOEpatents

Loughry, Thomas A.

2016-04-12

Systems and methods for decompressing compressed data that has been compressed by way of a lossless compression algorithm are described herein. In a general embodiment, a graphics processing unit (GPU) is programmed to receive compressed data packets and decompress such packets in parallel. The compressed data packets are compressed representations of an image, and the lossless compression algorithm is a Rice compression algorithm.

Experimental Investigation of Piston Heat Transfer in a Light Duty Engine Under Conventional Diesel, Homogeneous Charge Compression Ignition, and Reactivity Controlled Compression Ignition Combustion Regimes

DTIC Science & Technology

2014-01-15

in a Light Duty Engine Under Conventional Diesel, Homogeneous Charge Compression Ignition , and Reactivity Controlled Compression Ignition ...Conventional Diesel (CDC), Homogeneous Charge Compression Ignition (HCCI), and Reactivity Controlled Compression Ignition (RCCI) combustion...LTC) regimes, including reactivity controlled compression ignition (RCCI), partially premixed combustion (PPC), and homogenous charge compression

30 CFR 75.1730 - Compressed air; general; compressed air systems.

Code of Federal Regulations, 2013 CFR

2013-07-01

... 30 Mineral Resources 1 2013-07-01 2013-07-01 false Compressed air; general; compressed air systems... Compressed air; general; compressed air systems. (a) All pressure vessels shall be constructed, installed... Safety and Health district office. (b) Compressors and compressed-air receivers shall be equipped with...

30 CFR 75.1730 - Compressed air; general; compressed air systems.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 30 Mineral Resources 1 2012-07-01 2012-07-01 false Compressed air; general; compressed air systems... Compressed air; general; compressed air systems. (a) All pressure vessels shall be constructed, installed... Safety and Health district office. (b) Compressors and compressed-air receivers shall be equipped with...

30 CFR 75.1730 - Compressed air; general; compressed air systems.

Code of Federal Regulations, 2014 CFR

2014-07-01

... 30 Mineral Resources 1 2014-07-01 2014-07-01 false Compressed air; general; compressed air systems... Compressed air; general; compressed air systems. (a) All pressure vessels shall be constructed, installed... Safety and Health district office. (b) Compressors and compressed-air receivers shall be equipped with...

30 CFR 75.1730 - Compressed air; general; compressed air systems.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 30 Mineral Resources 1 2011-07-01 2011-07-01 false Compressed air; general; compressed air systems... Compressed air; general; compressed air systems. (a) All pressure vessels shall be constructed, installed... Safety and Health district office. (b) Compressors and compressed-air receivers shall be equipped with...

An Image Processing Technique for Achieving Lossy Compression of Data at Ratios in Excess of 100:1

DTIC Science & Technology

1992-11-01

5 Lempel , Ziv , Welch (LZW) Compression ............... 7 Lossless Compression Tests Results ................. 9 Exact...since IBM holds the patent for this technique. Lempel , Ziv , Welch (LZW) Compression The LZW compression is related to two compression techniques known as... compression , using the input stream as data . This step is possible because the compression algorithm always outputs the phrase and character components of a

Composeable Chat over Low-Bandwidth Intermittent Communication Links

DTIC Science & Technology

2007-04-01

Compression (STC), introduced in this report, is a data compression algorithm intended to compress alphanumeric... Ziv - Lempel coding, the grandfather of most modern general-purpose file compression programs, watches for input symbol sequences that have previously... data . This section applies these techniques to create a new compression algorithm called Small Text Compression . Various sequence compression

A hybrid data compression approach for online backup service

NASA Astrophysics Data System (ADS)

Wang, Hua; Zhou, Ke; Qin, MingKang

2009-08-01

With the popularity of Saas (Software as a service), backup service has becoming a hot topic of storage application. Due to the numerous backup users, how to reduce the massive data load is a key problem for system designer. Data compression provides a good solution. Traditional data compression application used to adopt a single method, which has limitations in some respects. For example data stream compression can only realize intra-file compression, de-duplication is used to eliminate inter-file redundant data, compression efficiency cannot meet the need of backup service software. This paper proposes a novel hybrid compression approach, which includes two levels: global compression and block compression. The former can eliminate redundant inter-file copies across different users, the latter adopts data stream compression technology to realize intra-file de-duplication. Several compressing algorithms were adopted to measure the compression ratio and CPU time. Adaptability using different algorithm in certain situation is also analyzed. The performance analysis shows that great improvement is made through the hybrid compression policy.

Cardiopulmonary resuscitation by chest compression alone or with mouth-to-mouth ventilation.

PubMed

Hallstrom, A; Cobb, L; Johnson, E; Copass, M

2000-05-25

Despite extensive training of citizens of Seattle in cardiopulmonary resuscitation (CPR), bystanders do not perform CPR in almost half of witnessed cardiac arrests. Instructions in chest compression plus mouth-to-mouth ventilation given by dispatchers over the telephone can require 2.4 minutes. In experimental studies, chest compression alone is associated with survival rates similar to those with chest compression plus mouth-to-mouth ventilation. We conducted a randomized study to compare CPR by chest compression alone with CPR by chest compression plus mouth-to-mouth ventilation. The setting of the trial was an urban, fire-department-based, emergency-medical-care system with central dispatching. In a randomized manner, telephone dispatchers gave bystanders at the scene of apparent cardiac arrest instructions in either chest compression alone or chest compression plus mouth-to-mouth ventilation. The primary end point was survival to hospital discharge. Data were analyzed for 241 patients randomly assigned to receive chest compression alone and 279 assigned to chest compression plus mouth-to-mouth ventilation. Complete instructions were delivered in 62 percent of episodes for the group receiving chest compression plus mouth-to-mouth ventilation and 81 percent of episodes for the group receiving chest compression alone (P=0.005). Instructions for compression required 1.4 minutes less to complete than instructions for compression plus mouth-to-mouth ventilation. Survival to hospital discharge was better among patients assigned to chest compression alone than among those assigned to chest compression plus mouth-to-mouth ventilation (14.6 percent vs. 10.4 percent), but the difference was not statistically significant (P=0.18). The outcome after CPR with chest compression alone is similar to that after chest compression with mouth-to-mouth ventilation, and chest compression alone may be the preferred approach for bystanders inexperienced in CPR.

Resuscitation quality of rotating chest compression providers at one-minute vs. two-minute intervals: A mannequin study.

PubMed

Kılıç, D; Göksu, E; Kılıç, T; Buyurgan, C S

2018-05-01

The aim of this randomized cross-over study was to compare one-minute and two-minute continuous chest compressions in terms of chest compression only CPR quality metrics on a mannequin model in the ED. Thirty-six emergency medicine residents participated in this study. In the 1-minute group, there was no statistically significant difference in the mean compression rate (p=0.83), mean compression depth (p=0.61), good compressions (p=0.31), the percentage of complete release (p=0.07), adequate compression depth (p=0.11) or the percentage of good rate (p=51) over the four-minute time period. Only flow time was statistically significant among the 1-minute intervals (p<0.001). In the 2-minute group, the mean compression depth (p=0.19), good compression (p=0.92), the percentage of complete release (p=0.28), adequate compression depth (p=0.96), and the percentage of good rate (p=0.09) were not statistically significant over time. In this group, the number of compressions (248±31 vs 253±33, p=0.01) and mean compression rates (123±15 vs 126±17, p=0.01) and flow time (p=0.001) were statistically significant along the two-minute intervals. There was no statistically significant difference in the mean number of chest compressions per minute, mean chest compression depth, the percentage of good compressions, complete release, adequate chest compression depth and percentage of good compression between the 1-minute and 2-minute groups. There was no statistically significant difference in the quality metrics of chest compressions between 1- and 2-minute chest compression only groups. Copyright © 2017 Elsevier Inc. All rights reserved.

TAPAS, a VO archive at the IRAM 30-m telescope

NASA Astrophysics Data System (ADS)

Leon, Stephane; Espigares, Victor; Ruíz, José Enrique; Verdes-Montenegro, Lourdes; Mauersberger, Rainer; Brunswig, Walter; Kramer, Carsten; Santander-Vela, Juan de Dios; Wiesemeyer, Helmut

2012-07-01

Astronomical observatories are today generating increasingly large volumes of data. For an efficient use of them, databases have been built following the standards proposed by the International Virtual Observatory Alliance (IVOA), providing a common protocol to query them and make them interoperable. The IRAM 30-m radio telescope, located in Sierra Nevada (Granada, Spain) is a millimeter wavelength telescope with a constantly renewed, extensive choice of instruments, and capable of covering the frequency range between 80 and 370 GHz. It is continuously producing a large amount of data thanks to the more than 200 scientific projects observed each year. The TAPAS archive at the IRAM 30-m telescope is aimed to provide public access to the headers describing the observations performed with the telescope, according to a defined data policy, making as well the technical data available to the IRAM staff members. A special emphasis has been made to make it Virtual Observatory (VO) compliant, and to offer a VO compliant web interface allowing to make the information available to the scientific community. TAPAS is built using the Django Python framework on top of a relational MySQL database, and is fully integrated with the telescope control system. The TAPAS data model (DM) is based on the Radio Astronomical DAta Model for Single dish radio telescopes (RADAMS), to allow for easy integration into the VO infrastructure. A metadata modeling layer is used by the data-filler to allow an implementation free from assumptions about the control system and the underlying database. TAPAS and its public web interface ( http://tapas.iram.es ) provides a scalable system that can evolve with new instruments and observing modes. A meta description of the DM has been introduced in TAPAS in order to both avoid undesired coupling between the code and the DM and to provide a better management of the archive. A subset of the header data stored in TAPAS will be made available at the CDS.

VizieR Online Data Catalog: Soft X-ray standards (Beuermann+, 2006)

NASA Astrophysics Data System (ADS)

Beuermann, K.; Burwitz, V.; Rauch, T.

2006-08-01

Table A1 contains the area correction functions to the Chandra LETG+HRCS effective areas for the negative and positive dispersion directions, alphaneg, alphapos, and their area-weighted mean alpha as well as the corrected effective areas for a gravity of HZ43A of logg=7.90. Tables A2 and A3 are for logg=7.80 and 8.00, respectively. The corrected area A is obtained as the recommended area of the Chandra November 2004 release (http://cxc.harvard.edu/cal/Letg, LETG/HRC-S Effective Area, updated November 2004), referred to as A0 in the paper, multiplied with the correction function alpha (see Section 4.4.1 of the paper for further explanation). The variation of the correction functions alpha and the corrected areas A between the three tables indicate their systematic errors around the nominal values of Table A1 which are depicted in Fig. 5 of the paper. The columns of Tables A1 to A3 provide the wavelength Lambda ({AA}), alphaneg, alphapos, alpha, Aneg (cm2), Apos (cm2), and A (cm2). The header to each Table contains the parameters of the respective fit. Table A4 contains the best-fit incident soft X-ray spectra of HZ43A, SiriusB, and RXJ1856-37 for a gravity of HZ43A of logg=7.90 as shown in Fig. 6 of the paper (see also Table 3 of the paper). Tables A5 and A6 are for logg=7.80 and 8.00, respectively. The best-fit spectra are based on the most recent version of the Tuebingen Model Atmosphere Package TMAP (Werner et al. 2003, in: Workshop on Stellar Atmosphere Modeling, eds. I. Hubeny, D. Mihalas, K. Werner, ASP Conf. Ser. 288, 31; Rauch & Deetjen 2003, ASP Conf. Ser. 288, 103). The columns of Tables A1 to A3 provide the wavelength Lambda ({AA}) and the photon fluxes of the three stars in photons/cm2/s/{AA}. The header to each Table contains the parameters of the respective fit. (6 data files).

Automated measurements of metabolic tumor volume and metabolic parameters in lung PET/CT imaging

NASA Astrophysics Data System (ADS)

Orologas, F.; Saitis, P.; Kallergi, M.

2017-11-01

Patients with lung tumors or inflammatory lung disease could greatly benefit in terms of treatment and follow-up by PET/CT quantitative imaging, namely measurements of metabolic tumor volume (MTV), standardized uptake values (SUVs) and total lesion glycolysis (TLG). The purpose of this study was the development of an unsupervised or partially supervised algorithm using standard image processing tools for measuring MTV, SUV, and TLG from lung PET/CT scans. Automated metabolic lesion volume and metabolic parameter measurements were achieved through a 5 step algorithm: (i) The segmentation of the lung areas on the CT slices, (ii) the registration of the CT segmented lung regions on the PET images to define the anatomical boundaries of the lungs on the functional data, (iii) the segmentation of the regions of interest (ROIs) on the PET images based on adaptive thresholding and clinical criteria, (iv) the estimation of the number of pixels and pixel intensities in the PET slices of the segmented ROIs, (v) the estimation of MTV, SUVs, and TLG from the previous step and DICOM header data. Whole body PET/CT scans of patients with sarcoidosis were used for training and testing the algorithm. Lung area segmentation on the CT slices was better achieved with semi-supervised techniques that reduced false positive detections significantly. Lung segmentation results agreed with the lung volumes published in the literature while the agreement between experts and algorithm in the segmentation of the lesions was around 88%. Segmentation results depended on the image resolution selected for processing. The clinical parameters, SUV (either mean or max or peak) and TLG estimated by the segmented ROIs and DICOM header data provided a way to correlate imaging data to clinical and demographic data. In conclusion, automated MTV, SUV, and TLG measurements offer powerful analysis tools in PET/CT imaging of the lungs. Custom-made algorithms are often a better approach than the manufacturer’s general analysis software at much lower cost. Relatively simple processing techniques could lead to customized, unsupervised or partially supervised methods that can successfully perform the desirable analysis and adapt to the specific disease requirements.

Induction of a shorter compression phase is correlated with a deeper chest compression during metronome-guided cardiopulmonary resuscitation: a manikin study.

PubMed

Chung, Tae Nyoung; Bae, Jinkun; Kim, Eui Chung; Cho, Yun Kyung; You, Je Sung; Choi, Sung Wook; Kim, Ok Jun

2013-07-01

Recent studies have shown that there may be an interaction between duty cycle and other factors related to the quality of chest compression. Duty cycle represents the fraction of compression phase. We aimed to investigate the effect of shorter compression phase on average chest compression depth during metronome-guided cardiopulmonary resuscitation. Senior medical students performed 12 sets of chest compressions following the guiding sounds, with three down-stroke patterns (normal, fast and very fast) and four rates (80, 100, 120 and 140 compressions/min) in random sequence. Repeated-measures analysis of variance was used to compare the average chest compression depth and duty cycle among the trials. The average chest compression depth increased and the duty cycle decreased in a linear fashion as the down-stroke pattern shifted from normal to very fast (p<0.001 for both). Linear increase of average chest compression depth following the increase of the rate of chest compression was observed only with normal down-stroke pattern (p=0.004). Induction of a shorter compression phase is correlated with a deeper chest compression during metronome-guided cardiopulmonary resuscitation.

DNABIT Compress – Genome compression algorithm

PubMed Central

Rajarajeswari, Pothuraju; Apparao, Allam

2011-01-01

Data compression is concerned with how information is organized in data. Efficient storage means removal of redundancy from the data being stored in the DNA molecule. Data compression algorithms remove redundancy and are used to understand biologically important molecules. We present a compression algorithm, “DNABIT Compress” for DNA sequences based on a novel algorithm of assigning binary bits for smaller segments of DNA bases to compress both repetitive and non repetitive DNA sequence. Our proposed algorithm achieves the best compression ratio for DNA sequences for larger genome. Significantly better compression results show that “DNABIT Compress” algorithm is the best among the remaining compression algorithms. While achieving the best compression ratios for DNA sequences (Genomes),our new DNABIT Compress algorithm significantly improves the running time of all previous DNA compression programs. Assigning binary bits (Unique BIT CODE) for (Exact Repeats, Reverse Repeats) fragments of DNA sequence is also a unique concept introduced in this algorithm for the first time in DNA compression. This proposed new algorithm could achieve the best compression ratio as much as 1.58 bits/bases where the existing best methods could not achieve a ratio less than 1.72 bits/bases. PMID:21383923

The effect of compression on individual pressure vessel nickel/hydrogen components

NASA Technical Reports Server (NTRS)

Manzo, Michelle A.; Perez-Davis, Marla E.

1988-01-01

Compression tests were performed on representative Individual Pressure Vessel (IPV) Nickel/Hydrogen cell components in an effort to better understand the effects of force on component compression and the interactions of components under compression. It appears that the separator is the most easily compressed of all of the stack components. It will typically partially compress before any of the other components begin to compress. The compression characteristics of the cell components in assembly differed considerably from what would be predicted based on individual compression characteristics. Component interactions played a significant role in the stack response to compression. The results of the compression tests were factored into the design and selection of Belleville washers added to the cell stack to accommodate nickel electrode expansion while keeping the pressure on the stack within a reasonable range of the original preset.

Squeezing the muscle: compression clothing and muscle metabolism during recovery from high intensity exercise.

PubMed

Sperlich, Billy; Born, Dennis-Peter; Kaskinoro, Kimmo; Kalliokoski, Kari K; Laaksonen, Marko S

2013-01-01

The purpose of this experiment was to investigate skeletal muscle blood flow and glucose uptake in m. biceps (BF) and m. quadriceps femoris (QF) 1) during recovery from high intensity cycle exercise, and 2) while wearing a compression short applying ~37 mmHg to the thigh muscles. Blood flow and glucose uptake were measured in the compressed and non-compressed leg of 6 healthy men by using positron emission tomography. At baseline blood flow in QF (P = 0.79) and BF (P = 0.90) did not differ between the compressed and the non-compressed leg. During recovery muscle blood flow was higher compared to baseline in both compressed (P<0.01) and non-compressed QF (P<0.001) but not in compressed (P = 0.41) and non-compressed BF (P = 0.05; effect size = 2.74). During recovery blood flow was lower in compressed QF (P<0.01) but not in BF (P = 0.26) compared to the non-compressed muscles. During baseline and recovery no differences in blood flow were detected between the superficial and deep parts of QF in both, compressed (baseline P = 0.79; recovery P = 0.68) and non-compressed leg (baseline P = 0.64; recovery P = 0.06). During recovery glucose uptake was higher in QF compared to BF in both conditions (P<0.01) with no difference between the compressed and non-compressed thigh. Glucose uptake was higher in the deep compared to the superficial parts of QF (compression leg P = 0.02). These results demonstrate that wearing compression shorts with ~37 mmHg of external pressure reduces blood flow both in the deep and superficial regions of muscle tissue during recovery from high intensity exercise but does not affect glucose uptake in BF and QF.

Lossless Astronomical Image Compression and the Effects of Random Noise

NASA Technical Reports Server (NTRS)

Pence, William

2009-01-01

In this paper we compare a variety of modern image compression methods on a large sample of astronomical images. We begin by demonstrating from first principles how the amount of noise in the image pixel values sets a theoretical upper limit on the lossless compression ratio of the image. We derive simple procedures for measuring the amount of noise in an image and for quantitatively predicting how much compression will be possible. We then compare the traditional technique of using the GZIP utility to externally compress the image, with a newer technique of dividing the image into tiles, and then compressing and storing each tile in a FITS binary table structure. This tiled-image compression technique offers a choice of other compression algorithms besides GZIP, some of which are much better suited to compressing astronomical images. Our tests on a large sample of images show that the Rice algorithm provides the best combination of speed and compression efficiency. In particular, Rice typically produces 1.5 times greater compression and provides much faster compression speed than GZIP. Floating point images generally contain too much noise to be effectively compressed with any lossless algorithm. We have developed a compression technique which discards some of the useless noise bits by quantizing the pixel values as scaled integers. The integer images can then be compressed by a factor of 4 or more. Our image compression and uncompression utilities (called fpack and funpack) that were used in this study are publicly available from the HEASARC web site.Users may run these stand-alone programs to compress and uncompress their own images.

Image quality (IQ) guided multispectral image compression

NASA Astrophysics Data System (ADS)

Zheng, Yufeng; Chen, Genshe; Wang, Zhonghai; Blasch, Erik

2016-05-01

Image compression is necessary for data transportation, which saves both transferring time and storage space. In this paper, we focus on our discussion on lossy compression. There are many standard image formats and corresponding compression algorithms, for examples, JPEG (DCT -- discrete cosine transform), JPEG 2000 (DWT -- discrete wavelet transform), BPG (better portable graphics) and TIFF (LZW -- Lempel-Ziv-Welch). The image quality (IQ) of decompressed image will be measured by numerical metrics such as root mean square error (RMSE), peak signal-to-noise ratio (PSNR), and structural Similarity (SSIM) Index. Given an image and a specified IQ, we will investigate how to select a compression method and its parameters to achieve an expected compression. Our scenario consists of 3 steps. The first step is to compress a set of interested images by varying parameters and compute their IQs for each compression method. The second step is to create several regression models per compression method after analyzing the IQ-measurement versus compression-parameter from a number of compressed images. The third step is to compress the given image with the specified IQ using the selected compression method (JPEG, JPEG2000, BPG, or TIFF) according to the regressed models. The IQ may be specified by a compression ratio (e.g., 100), then we will select the compression method of the highest IQ (SSIM, or PSNR). Or the IQ may be specified by a IQ metric (e.g., SSIM = 0.8, or PSNR = 50), then we will select the compression method of the highest compression ratio. Our experiments tested on thermal (long-wave infrared) images (in gray scales) showed very promising results.

Application of content-based image compression to telepathology

NASA Astrophysics Data System (ADS)

Varga, Margaret J.; Ducksbury, Paul G.; Callagy, Grace

2002-05-01

Telepathology is a means of practicing pathology at a distance, viewing images on a computer display rather than directly through a microscope. Without compression, images take too long to transmit to a remote location and are very expensive to store for future examination. However, to date the use of compressed images in pathology remains controversial. This is because commercial image compression algorithms such as JPEG achieve data compression without knowledge of the diagnostic content. Often images are lossily compressed at the expense of corrupting informative content. None of the currently available lossy compression techniques are concerned with what information has been preserved and what data has been discarded. Their sole objective is to compress and transmit the images as fast as possible. By contrast, this paper presents a novel image compression technique, which exploits knowledge of the slide diagnostic content. This 'content based' approach combines visually lossless and lossy compression techniques, judiciously applying each in the appropriate context across an image so as to maintain 'diagnostic' information while still maximising the possible compression. Standard compression algorithms, e.g. wavelets, can still be used, but their use in a context sensitive manner can offer high compression ratios and preservation of diagnostically important information. When compared with lossless compression the novel content-based approach can potentially provide the same degree of information with a smaller amount of data. When compared with lossy compression it can provide more information for a given amount of compression. The precise gain in the compression performance depends on the application (e.g. database archive or second opinion consultation) and the diagnostic content of the images.

Data Compression Techniques for Maps

DTIC Science & Technology

1989-01-01

Lempel - Ziv compression is applied to the classified and unclassified images as also to the output of the compression algorithms . The algorithms ...resulted in a compression of 7:1. The output of the quadtree coding algorithm was then compressed using Lempel - Ziv coding. The compression ratio achieved...using Lempel - Ziv coding. The unclassified image gave a compression ratio of only 1.4:1. The K means classified image

The effect of hydraulic bed movement on the quality of chest compressions.

PubMed

Park, Maeng Real; Lee, Dae Sup; In Kim, Yong; Ryu, Ji Ho; Cho, Young Mo; Kim, Hyung Bin; Yeom, Seok Ran; Min, Mun Ki

2017-08-01

The hydraulic height control systems of hospital beds provide convenience and shock absorption. However, movements in a hydraulic bed may reduce the effectiveness of chest compressions. This study investigated the effects of hydraulic bed movement on chest compressions. Twenty-eight participants were recruited for this study. All participants performed chest compressions for 2min on a manikin and three surfaces: the floor (Day 1), a firm plywood bed (Day 2), and a hydraulic bed (Day 3). We considered 28 participants of Day 1 as control and each 28 participants of Day 2 and Day 3 as study subjects. The compression rates, depths, and good compression ratios (>5-cm compressions/all compressions) were compared between the three surfaces. When we compared the three surfaces, we did not detect a significant difference in the speed of chest compressions (p=0.582). However, significantly lower values were observed on the hydraulic bed in terms of compression depth (p=0.001) and the good compression ratio (p=0.003) compared to floor compressions. When we compared the plywood and hydraulic beds, we did not detect significant differences in compression depth (p=0.351) and the good compression ratio (p=0.391). These results indicate that the movements in our hydraulic bed were associated with a non-statistically significant trend towards lower-quality chest compressions. Copyright © 2017 Elsevier Inc. All rights reserved.

Compression of surface myoelectric signals using MP3 encoding.

PubMed

Chan, Adrian D C

2011-01-01

The potential of MP3 compression of surface myoelectric signals is explored in this paper. MP3 compression is a perceptual-based encoder scheme, used traditionally to compress audio signals. The ubiquity of MP3 compression (e.g., portable consumer electronics and internet applications) makes it an attractive option for remote monitoring and telemedicine applications. The effects of muscle site and contraction type are examined at different MP3 encoding bitrates. Results demonstrate that MP3 compression is sensitive to the myoelectric signal bandwidth, with larger signal distortion associated with myoelectric signals that have higher bandwidths. Compared to other myoelectric signal compression techniques reported previously (embedded zero-tree wavelet compression and adaptive differential pulse code modulation), MP3 compression demonstrates superior performance (i.e., lower percent residual differences for the same compression ratios).

Low-Complexity Lossless and Near-Lossless Data Compression Technique for Multispectral Imagery

NASA Technical Reports Server (NTRS)

Xie, Hua; Klimesh, Matthew A.

2009-01-01

This work extends the lossless data compression technique described in Fast Lossless Compression of Multispectral- Image Data, (NPO-42517) NASA Tech Briefs, Vol. 30, No. 8 (August 2006), page 26. The original technique was extended to include a near-lossless compression option, allowing substantially smaller compressed file sizes when a small amount of distortion can be tolerated. Near-lossless compression is obtained by including a quantization step prior to encoding of prediction residuals. The original technique uses lossless predictive compression and is designed for use on multispectral imagery. A lossless predictive data compression algorithm compresses a digitized signal one sample at a time as follows: First, a sample value is predicted from previously encoded samples. The difference between the actual sample value and the prediction is called the prediction residual. The prediction residual is encoded into the compressed file. The decompressor can form the same predicted sample and can decode the prediction residual from the compressed file, and so can reconstruct the original sample. A lossless predictive compression algorithm can generally be converted to a near-lossless compression algorithm by quantizing the prediction residuals prior to encoding them. In this case, since the reconstructed sample values will not be identical to the original sample values, the encoder must determine the values that will be reconstructed and use these values for predicting later sample values. The technique described here uses this method, starting with the original technique, to allow near-lossless compression. The extension to allow near-lossless compression adds the ability to achieve much more compression when small amounts of distortion are tolerable, while retaining the low complexity and good overall compression effectiveness of the original algorithm.

FRESCO: Referential compression of highly similar sequences.

PubMed

Wandelt, Sebastian; Leser, Ulf

2013-01-01

In many applications, sets of similar texts or sequences are of high importance. Prominent examples are revision histories of documents or genomic sequences. Modern high-throughput sequencing technologies are able to generate DNA sequences at an ever-increasing rate. In parallel to the decreasing experimental time and cost necessary to produce DNA sequences, computational requirements for analysis and storage of the sequences are steeply increasing. Compression is a key technology to deal with this challenge. Recently, referential compression schemes, storing only the differences between a to-be-compressed input and a known reference sequence, gained a lot of interest in this field. In this paper, we propose a general open-source framework to compress large amounts of biological sequence data called Framework for REferential Sequence COmpression (FRESCO). Our basic compression algorithm is shown to be one to two orders of magnitudes faster than comparable related work, while achieving similar compression ratios. We also propose several techniques to further increase compression ratios, while still retaining the advantage in speed: 1) selecting a good reference sequence; and 2) rewriting a reference sequence to allow for better compression. In addition,we propose a new way of further boosting the compression ratios by applying referential compression to already referentially compressed files (second-order compression). This technique allows for compression ratios way beyond state of the art, for instance,4,000:1 and higher for human genomes. We evaluate our algorithms on a large data set from three different species (more than 1,000 genomes, more than 3 TB) and on a collection of versions of Wikipedia pages. Our results show that real-time compression of highly similar sequences at high compression ratios is possible on modern hardware.

The effect of different torque wrenches on rotational stiffness in compressive femoral nails: a biomechanical study.

PubMed

Karaarslan, A A; Acar, N

2018-02-01

Rotation instability and locking screws failure are common problems. We aimed to determine optimal torque wrench offering maximum rotational stiffness without locking screw failure. We used 10 conventional compression nails, 10 novel compression nails and 10 interlocking nails with 30 composite femurs. We examined rotation stiffness and fracture site compression value by load cell with 3, 6 and 8 Nm torque wrenches using torsion apparatus with a maximum torque moment of 5 Nm in both directions. Rotational stiffness of composite femur-nail constructs was calculated. Rotational stiffness of composite femur-compression nail constructs compressed by 6 Nm torque wrench was 3.27 ± 1.81 Nm/angle (fracture site compression: 1588 N) and 60% more than that compressed with 3 Nm torque wrench (advised previously) with 2.04 ± 0.81 Nm/angle (inter fragmentary compression: 818 N) (P = 0.000). Rotational stiffness of composite-femur-compression nail constructs compressed by 3 Nm torque wrench was 2.04 ± 0.81 Nm/angle (fracture site compression: 818 N) and 277% more than that of interlocking nail with 0.54 ± 0.08 Nm/angle (fracture site compression: 0 N) (P = 0.000). Rotational stiffness and fracture site compression value produced by 3 Nm torque wrench was not satisfactory. To obtain maximum rotational stiffness and fracture site compression value without locking screw failure, 6 Nm torque wrench in compression nails and 8 Nm torque wrench in novel compression nails should be used.

Two-dimensional compression of surface electromyographic signals using column-correlation sorting and image encoders.

PubMed

Costa, Marcus V C; Carvalho, Joao L A; Berger, Pedro A; Zaghetto, Alexandre; da Rocha, Adson F; Nascimento, Francisco A O

2009-01-01

We present a new preprocessing technique for two-dimensional compression of surface electromyographic (S-EMG) signals, based on correlation sorting. We show that the JPEG2000 coding system (originally designed for compression of still images) and the H.264/AVC encoder (video compression algorithm operating in intraframe mode) can be used for compression of S-EMG signals. We compare the performance of these two off-the-shelf image compression algorithms for S-EMG compression, with and without the proposed preprocessing step. Compression of both isotonic and isometric contraction S-EMG signals is evaluated. The proposed methods were compared with other S-EMG compression algorithms from the literature.

Compressing DNA sequence databases with coil.

PubMed

White, W Timothy J; Hendy, Michael D

2008-05-20

Publicly available DNA sequence databases such as GenBank are large, and are growing at an exponential rate. The sheer volume of data being dealt with presents serious storage and data communications problems. Currently, sequence data is usually kept in large "flat files," which are then compressed using standard Lempel-Ziv (gzip) compression - an approach which rarely achieves good compression ratios. While much research has been done on compressing individual DNA sequences, surprisingly little has focused on the compression of entire databases of such sequences. In this study we introduce the sequence database compression software coil. We have designed and implemented a portable software package, coil, for compressing and decompressing DNA sequence databases based on the idea of edit-tree coding. coil is geared towards achieving high compression ratios at the expense of execution time and memory usage during compression - the compression time represents a "one-off investment" whose cost is quickly amortised if the resulting compressed file is transmitted many times. Decompression requires little memory and is extremely fast. We demonstrate a 5% improvement in compression ratio over state-of-the-art general-purpose compression tools for a large GenBank database file containing Expressed Sequence Tag (EST) data. Finally, coil can efficiently encode incremental additions to a sequence database. coil presents a compelling alternative to conventional compression of flat files for the storage and distribution of DNA sequence databases having a narrow distribution of sequence lengths, such as EST data. Increasing compression levels for databases having a wide distribution of sequence lengths is a direction for future work.

Compressing DNA sequence databases with coil

PubMed Central

White, W Timothy J; Hendy, Michael D

2008-01-01

Background Publicly available DNA sequence databases such as GenBank are large, and are growing at an exponential rate. The sheer volume of data being dealt with presents serious storage and data communications problems. Currently, sequence data is usually kept in large "flat files," which are then compressed using standard Lempel-Ziv (gzip) compression – an approach which rarely achieves good compression ratios. While much research has been done on compressing individual DNA sequences, surprisingly little has focused on the compression of entire databases of such sequences. In this study we introduce the sequence database compression software coil. Results We have designed and implemented a portable software package, coil, for compressing and decompressing DNA sequence databases based on the idea of edit-tree coding. coil is geared towards achieving high compression ratios at the expense of execution time and memory usage during compression – the compression time represents a "one-off investment" whose cost is quickly amortised if the resulting compressed file is transmitted many times. Decompression requires little memory and is extremely fast. We demonstrate a 5% improvement in compression ratio over state-of-the-art general-purpose compression tools for a large GenBank database file containing Expressed Sequence Tag (EST) data. Finally, coil can efficiently encode incremental additions to a sequence database. Conclusion coil presents a compelling alternative to conventional compression of flat files for the storage and distribution of DNA sequence databases having a narrow distribution of sequence lengths, such as EST data. Increasing compression levels for databases having a wide distribution of sequence lengths is a direction for future work. PMID:18489794

Evaluation of supercapacitors for space applications under thermal vacuum conditions

NASA Astrophysics Data System (ADS)

Chin, Keith C.; Green, Nelson W.; Brandon, Erik J.

2018-03-01

Commercially available supercapacitor cells from three separate vendors were evaluated for use in a space environment using thermal vacuum (Tvac) testing. Standard commercial cells are not hermetically sealed, but feature crimp or double seam seals between the header and the can, which may not maintain an adequate seal under vacuum. Cells were placed in a small vacuum chamber, and cycled between three separate temperature set points. Charging and discharging of cells was executed following each temperature soak, to confirm there was no significant impact on performance. A final electrical performance check, visual inspection and mass check following testing were also performed, to confirm the integrity of the cells had not been compromised during exposure to thermal cycling under vacuum. All cells tested were found to survive this testing protocol and exhibited no significant impact on electrical performance.

Segmented annular combustor

DOEpatents

Reider, Samuel B.

1979-01-01

An industrial gas turbine engine includes an inclined annular combustor made up of a plurality of support segments each including inner and outer walls of trapezoidally configured planar configuration extents and including side flanges thereon interconnected by means of air cooled connector bolt assemblies to form a continuous annular combustion chamber therebetween and wherein an air fuel mixing chamber is formed at one end of the support segments including means for directing and mixing fuel within a plenum and a perforated header plate for directing streams of air and fuel mixture into the combustion chamber; each of the outer and inner walls of each of the support segments having a ribbed lattice with tracks slidably supporting porous laminated replaceable panels and including pores therein for distributing combustion air into the combustion chamber while cooling the inner surface of each of the panels by transpiration cooling thereof.

Replacing the CCSDS Telecommand Protocol with Next Generation Uplink

NASA Technical Reports Server (NTRS)

Kazz, Greg; Burleigh, Scott; Greenberg, Ed

2012-01-01

Better performing Forward Error Correction on the forward link along with adequate power in the data open an uplink operations trade space that enable missions to: Command to greater distances in deep space (increased uplink margin) Increase the size of the payload data (latency may be a factor) Provides space for the security header/trailer of the CCSDS Space Data Link Security Protocol Note: These higher rates could be used for relief of emergency communication margins/rates and not limited to improving top-end rate performance. A higher performance uplink could also reduce the requirements on flight emergency antenna size and/or the performance required from ground stations. Use of a selective repeat ARQ protocol may increase the uplink design requirements but the resultant development is deemed acceptable, due the factor of 4 to 8 potential increase in uplink data rate.

Devices and methods for managing noncombustible gasses in nuclear power plants

DOEpatents

Marquino, Wayne; Moen, Stephan C; Wachowiak, Richard M; Gels, John L; Diaz-Quiroz, Jesus; Burns, Jr., John C

2014-12-23

Systems passively eliminate noncondensable gasses from facilities susceptible to damage from combustion of built-up noncondensable gasses, such as H2 and O2 in nuclear power plants, without the need for external power and/or moving parts. Systems include catalyst plates installed in a lower header of the Passive Containment Cooling System (PCCS) condenser, a catalyst packing member, and/or a catalyst coating on an interior surface of a condensation tube of the PCCS condenser or an annular outlet of the PCCS condenser. Structures may have surfaces or hydrophobic elements that inhibit water formation and promote contact with the noncondensable gas. Noncondensable gasses in a nuclear power plant are eliminated by installing and using the systems individually or in combination. An operating pressure of the PCCS condenser may be increased to facilitate recombination of noncondensable gasses therein.

Devices and methods for managing noncondensable gasses in nuclear power plants

DOEpatents

Marquino, Wayne; Moen, Stephan C.; Wachowiak, Richard M.; Gels, John L.; Diaz-Quiroz, Jesus; Burns, Jr., John C.

2016-11-15

Systems passively eliminate noncondensable gasses from facilities susceptible to damage from combustion of built-up noncondensable gasses, such as H2 and O2 in nuclear power plants, without the need for external power and/or moving parts. Systems include catalyst plates installed in a lower header of the Passive Containment Cooling System (PCCS) condenser, a catalyst packing member, and/or a catalyst coating on an interior surface of a condensation tube of the PCCS condenser or an annular outlet of the PCCS condenser. Structures may have surfaces or hydrophobic elements that inhibit water formation and promote contact with the noncondensable gas. Noncondensable gasses in a nuclear power plant are eliminated by installing and using the systems individually or in combination. An operating pressure of the PCCS condenser may be increased to facilitate recombination of noncondensable gasses therein.

Application of stochastic discrete event system framework for detection of induced low rate TCP attack.

PubMed

Barbhuiya, F A; Agarwal, Mayank; Purwar, Sanketh; Biswas, Santosh; Nandi, Sukumar

2015-09-01

TCP is the most widely accepted transport layer protocol. The major emphasis during the development of TCP was its functionality and efficiency. However, not much consideration was given on studying the possibility of attackers exploiting the protocol, which has lead to several attacks on TCP. This paper deals with the induced low rate TCP attack. Since the attack is relatively new, only a few schemes have been proposed to mitigate it. However, the main issues with these schemes are scalability, change in TCP header, lack of formal frameworks, etc. In this paper, we have adapted the stochastic DES framework for detecting the attack, which addresses most of these issues. We have successfully deployed and tested the proposed DES based IDS on a test bed. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

NAND Flash Qualification Guideline

NASA Technical Reports Server (NTRS)

Heidecker, Jason

2012-01-01

Better performing Forward Error Correction on the forward link along with adequate power in the data open an uplink operations trade space that enable missions to: Command to greater distances in deep space (increased uplink margin). Increase the size of the payload data (latency may be a factor). Provides space for the security header/trailer of the CCSDS Space Data Link Security Protocol. Note: These higher rates could be used for relief of emergency communication margins/rates and not limited to improving top-end rate performance. A higher performance uplink could also reduce the requirements on flight emergency antenna size and/or the performance required from ground stations. Use of a selective repeat ARQ protocol may increase the uplink design requirements but the resultant development is deemed acceptable, due the factor of 4 to 8 potential increase in uplink data rate.

Natural Good Theories and the Value of Human Dignity.

PubMed

Muders, Sebastian

2016-04-01

One of the widely recognized facts about human dignity is its vastly divergent applicability-from highly controversial issues in bioethics to broader topics in political philosophy. A group of theories that this article subsumes under the header "natural good theories" appears to be especially fitted for normatively multifaceted notions like dignity. However, the heavy normative weight the concept of dignity has to bear due to the central position it occupies within these theories creates its own difficulties. As is shown in a discussion of Martha Nussbaum's capability conception of dignity, dignity appears to be unable to mirror the special normative relevance people want to assign to it in cases of great moral misconduct. The article provides a suggestion on how to solve this problem by means of paradigmatic cases that work as material constraints regarding the exact boundaries of dignity violations.

Method for preventing jamming conditions in a compression device

DOEpatents

Williams, Paul M.; Faller, Kenneth M.; Bauer, Edward J.

2002-06-18

A compression device for feeding a waste material to a reactor includes a waste material feed assembly having a hopper, a supply tube and a compression tube. Each of the supply and compression tubes includes feed-inlet and feed-outlet ends. A feed-discharge valve assembly is located between the feed-outlet end of the compression tube and the reactor. A feed auger-screw extends axially in the supply tube between the feed-inlet and feed-outlet ends thereof. A compression auger-screw extends axially in the compression tube between the feed-inlet and feed-outlet ends thereof. The compression tube is sloped downwardly towards the reactor to drain fluid from the waste material to the reactor and is oriented at generally right angle to the supply tube such that the feed-outlet end of the supply tube is adjacent to the feed-inlet end of the compression tube. A programmable logic controller is provided for controlling the rotational speed of the feed and compression auger-screws for selectively varying the compression of the waste material and for overcoming jamming conditions within either the supply tube or the compression tube.

JPEG and wavelet compression of ophthalmic images

NASA Astrophysics Data System (ADS)

Eikelboom, Robert H.; Yogesan, Kanagasingam; Constable, Ian J.; Barry, Christopher J.

1999-05-01

This study was designed to determine the degree and methods of digital image compression to produce ophthalmic imags of sufficient quality for transmission and diagnosis. The photographs of 15 subjects, which inclined eyes with normal, subtle and distinct pathologies, were digitized to produce 1.54MB images and compressed to five different methods: (i) objectively by calculating the RMS error between the uncompressed and compressed images, (ii) semi-subjectively by assessing the visibility of blood vessels, and (iii) subjectively by asking a number of experienced observers to assess the images for quality and clinical interpretation. Results showed that as a function of compressed image size, wavelet compressed images produced less RMS error than JPEG compressed images. Blood vessel branching could be observed to a greater extent after Wavelet compression compared to JPEG compression produced better images then a JPEG compression for a given image size. Overall, it was shown that images had to be compressed to below 2.5 percent for JPEG and 1.7 percent for Wavelet compression before fine detail was lost, or when image quality was too poor to make a reliable diagnosis.

Effect of the rate of chest compression familiarised in previous training on the depth of chest compression during metronome-guided cardiopulmonary resuscitation: a randomised crossover trial

PubMed Central

Bae, Jinkun; Chung, Tae Nyoung; Je, Sang Mo

2016-01-01

Objectives To assess how the quality of metronome-guided cardiopulmonary resuscitation (CPR) was affected by the chest compression rate familiarised by training before the performance and to determine a possible mechanism for any effect shown. Design Prospective crossover trial of a simulated, one-person, chest-compression-only CPR. Setting Participants were recruited from a medical school and two paramedic schools of South Korea. Participants 42 senior students of a medical school and two paramedic schools were enrolled but five dropped out due to physical restraints. Intervention Senior medical and paramedic students performed 1 min of metronome-guided CPR with chest compressions only at a speed of 120 compressions/min after training for chest compression with three different rates (100, 120 and 140 compressions/min). Friedman's test was used to compare average compression depths based on the different rates used during training. Results Average compression depths were significantly different according to the rate used in training (p<0.001). A post hoc analysis showed that average compression depths were significantly different between trials after training at a speed of 100 compressions/min and those at speeds of 120 and 140 compressions/min (both p<0.001). Conclusions The depth of chest compression during metronome-guided CPR is affected by the relative difference between the rate of metronome guidance and the chest compression rate practised in previous training. PMID:26873050

Displaying radiologic images on personal computers: image storage and compression--Part 2.

PubMed

Gillespy, T; Rowberg, A H

1994-02-01

This is part 2 of our article on image storage and compression, the third article of our series for radiologists and imaging scientists on displaying, manipulating, and analyzing radiologic images on personal computers. Image compression is classified as lossless (nondestructive) or lossy (destructive). Common lossless compression algorithms include variable-length bit codes (Huffman codes and variants), dictionary-based compression (Lempel-Ziv variants), and arithmetic coding. Huffman codes and the Lempel-Ziv-Welch (LZW) algorithm are commonly used for image compression. All of these compression methods are enhanced if the image has been transformed into a differential image based on a differential pulse-code modulation (DPCM) algorithm. The LZW compression after the DPCM image transformation performed the best on our example images, and performed almost as well as the best of the three commercial compression programs tested. Lossy compression techniques are capable of much higher data compression, but reduced image quality and compression artifacts may be noticeable. Lossy compression is comprised of three steps: transformation, quantization, and coding. Two commonly used transformation methods are the discrete cosine transformation and discrete wavelet transformation. In both methods, most of the image information is contained in a relatively few of the transformation coefficients. The quantization step reduces many of the lower order coefficients to 0, which greatly improves the efficiency of the coding (compression) step. In fractal-based image compression, image patterns are stored as equations that can be reconstructed at different levels of resolution.

Performance of a Discrete Wavelet Transform for Compressing Plasma Count Data and its Application to the Fast Plasma Investigation on NASA's Magnetospheric Multiscale Mission

NASA Technical Reports Server (NTRS)

Barrie, Alexander C.; Yeh, Penshu; Dorelli, John C.; Clark, George B.; Paterson, William R.; Adrian, Mark L.; Holland, Matthew P.; Lobell, James V.; Simpson, David G.; Pollock, Craig J.;

Chest compression rates and survival following out-of-hospital cardiac arrest.

PubMed

Idris, Ahamed H; Guffey, Danielle; Pepe, Paul E; Brown, Siobhan P; Brooks, Steven C; Callaway, Clifton W; Christenson, Jim; Davis, Daniel P; Daya, Mohamud R; Gray, Randal; Kudenchuk, Peter J; Larsen, Jonathan; Lin, Steve; Menegazzi, James J; Sheehan, Kellie; Sopko, George; Stiell, Ian; Nichol, Graham; Aufderheide, Tom P

2015-04-01

Guidelines for cardiopulmonary resuscitation recommend a chest compression rate of at least 100 compressions/min. A recent clinical study reported optimal return of spontaneous circulation with rates between 100 and 120/min during cardiopulmonary resuscitation for out-of-hospital cardiac arrest. However, the relationship between compression rate and survival is still undetermined. Prospective, observational study. Data is from the Resuscitation Outcomes Consortium Prehospital Resuscitation IMpedance threshold device and Early versus Delayed analysis clinical trial. Adults with out-of-hospital cardiac arrest treated by emergency medical service providers. None. Data were abstracted from monitor-defibrillator recordings for the first five minutes of emergency medical service cardiopulmonary resuscitation. Multiple logistic regression assessed odds ratio for survival by compression rate categories (<80, 80-99, 100-119, 120-139, ≥140), both unadjusted and adjusted for sex, age, witnessed status, attempted bystander cardiopulmonary resuscitation, location of arrest, chest compression fraction and depth, first rhythm, and study site. Compression rate data were available for 10,371 patients; 6,399 also had chest compression fraction and depth data. Age (mean±SD) was 67±16 years. Chest compression rate was 111±19 per minute, compression fraction was 0.70±0.17, and compression depth was 42±12 mm. Circulation was restored in 34%; 9% survived to hospital discharge. After adjustment for covariates without chest compression depth and fraction (n=10,371), a global test found no significant relationship between compression rate and survival (p=0.19). However, after adjustment for covariates including chest compression depth and fraction (n=6,399), the global test found a significant relationship between compression rate and survival (p=0.02), with the reference group (100-119 compressions/min) having the greatest likelihood for survival. After adjustment for chest compression fraction and depth, compression rates between 100 and 120 per minute were associated with greatest survival to hospital discharge.

System using data compression and hashing adapted for use for multimedia encryption

DOE Office of Scientific and Technical Information (OSTI.GOV)

Coffland, Douglas R

2011-07-12

A system and method is disclosed for multimedia encryption. Within the system of the present invention, a data compression module receives and compresses a media signal into a compressed data stream. A data acquisition module receives and selects a set of data from the compressed data stream. And, a hashing module receives and hashes the set of data into a keyword. The method of the present invention includes the steps of compressing a media signal into a compressed data stream; selecting a set of data from the compressed data stream; and hashing the set of data into a keyword.

Effect of compressibility on the hypervelocity penetration

NASA Astrophysics Data System (ADS)

Song, W. J.; Chen, X. W.; Chen, P.

2018-02-01

We further consider the effect of rod strength by employing the compressible penetration model to study the effect of compressibility on hypervelocity penetration. Meanwhile, we define different instances of penetration efficiency in various modified models and compare these penetration efficiencies to identify the effects of different factors in the compressible model. To systematically discuss the effect of compressibility in different metallic rod-target combinations, we construct three cases, i.e., the penetrations by the more compressible rod into the less compressible target, rod into the analogously compressible target, and the less compressible rod into the more compressible target. The effects of volumetric strain, internal energy, and strength on the penetration efficiency are analyzed simultaneously. It indicates that the compressibility of the rod and target increases the pressure at the rod/target interface. The more compressible rod/target has larger volumetric strain and higher internal energy. Both the larger volumetric strain and higher strength enhance the penetration or anti-penetration ability. On the other hand, the higher internal energy weakens the penetration or anti-penetration ability. The two trends conflict, but the volumetric strain dominates in the variation of the penetration efficiency, which would not approach the hydrodynamic limit if the rod and target are not analogously compressible. However, if the compressibility of the rod and target is analogous, it has little effect on the penetration efficiency.

Competitive Parallel Processing For Compression Of Data

NASA Technical Reports Server (NTRS)

Diner, Daniel B.; Fender, Antony R. H.

1990-01-01

Momentarily-best compression algorithm selected. Proposed competitive-parallel-processing system compresses data for transmission in channel of limited band-width. Likely application for compression lies in high-resolution, stereoscopic color-television broadcasting. Data from information-rich source like color-television camera compressed by several processors, each operating with different algorithm. Referee processor selects momentarily-best compressed output.

[Expression and significance of tumor necrosis factor alpha, matrix metalloproteinase 2 and collagen in skin tissue of pressure ulcer of rats].

PubMed

Wang, X H; Mao, T T; Pan, Y Y; Xie, H H; Zhang, H Y; Xiao, J; Jiang, L P

2016-03-01

To observe the expressions of tumor necrosis factor alpha (TNF-α), matrix metalloproteinase 2 (MMP-2) and collagen in local skin tissue of pressure ulcer of rats, and to explore the possible mechanism of the pathogenesis of pressure ulcer. Forty male SD rats were divided into normal control group, 3 d compression group, 5 d compression group, 7 d compression group, and 9 d compression group according to the random number table, with 8 rats in each group. The rats in normal control group did not receive any treatment, whereas the rats in the latter 4 groups were established the deep tissue injury model (3 d compression group) and pressure ulcer model (the other 3 groups) on the gracilis muscle on both hind limbs using a way of cycle compression of ischemia-reperfusion magnet. The rats in 3 d compression group received only three cycles of compression, while the compressed skin of the rats in 5 d compression group, 7 d compression group, and 9 d compression group were cut through and received pressure to 5, 7 and 9 cycles after three cycles of compression, respectively. The rats in 3 d compression group were sacrificed immediately after receiving compression for 3 d (the rats in normal control group were sacrificed at the same time), and the rats in the other 3 groups were respectively sacrificed after receiving compression for 5, 7, and 9 d, and the skin tissue on the central part of gracilis muscle on both hind limbs were harvested. The morphology of the skin tissue was observed with HE staining. The expression of collagen fiber was observed with Masson staining. The expressions of collagen type Ⅳ and MMP-2 were detected by immunohistochemical method. The expressions of TNF-α and phosphorylated NF kappa B (NF-κB) were determined by Western blotting. Data were processed with one-way analysis of variance and LSD test. (1) In normal control group, the skin tissue of rats was stratified squamous epithelium, with the clear skin structure, and there was no obvious infiltration of inflammatory cells. In 3 d compression group, the skin layers of rats were clear, with quite a few fibroblasts, and the inflammatory cells began to infiltrate. In 5 d compression group, 7 d compression group, and 9 d compression group, the epidermis of rats thickened, with the number of fibroblasts reduced, and the infiltration of inflammatory cells enhanced with the compressed time prolonging. (2) In normal control group, the collagen fibers in skin tissue of rats were arranged in order, with rich content. In 3 d compression group, the collagen fibers in skin tissue of rats were arranged orderly, with high expression level, which was similar to that in normal control group (P>0.05). In 5 d compression group and 7 d compression group, the collagen fibers in skin tissue of rats were arranged in disorder, with the expression level gradually reduced, which were significantly lower than that in normal control group (with P values below 0.01). In 9 d compression group, the expression of collagen fiber in skin tissue of rats was a little higher than that in 7 d compression group, but it was still significantly lower than that in normal control group (P<0.01). (3) The expressions of collagen type Ⅳ in skin tissue of rats in normal control group, 3 d compression group, 5 d compression group, 7 d compression group, and 9 d compression group were respectively 11.0±2.8, 9.0±1.7, 8.3±2.8, 5.1±1.8, and 5.4±1.2. The expression of collagen type Ⅳ in skin tissue of rats in 3 d compression group was similar to that in normal control group (P>0.05). The expressions of collagen type Ⅳ in skin tissue of rats in 5 d compression group, 7 d compression group, and 9 d compression group were significantly lower than that in normal control group (P<0.05 or P<0.01). The expression of MMP-2 in skin tissue of rats in 3 d compression group was similar to that in normal control group (P>0.05). The expressions of MMP-2 in skin tissue of rats in 5 d compression group, 7 d compression group, and 9 d compression group were significantly higher than that in normal control group (P<0.05 or P<0.01). (4) The expression of TNF-α in skin tissue of rats in normal control group was 0.48±0.11, and the expressions of TNF-α in skin tissue of rats in 3 d compression group, 5 d compression group, 7 d compression group, and 9 d compression group were respectively 0.84±0.08, 1.13±0.19, 1.34±0.16, and 1.52±0.23, which were all significantly higher than that in normal control group (with P values below 0.01). The expressions of phosphorylated NF-κB in skin tissue of rats in 3 d compression group and 9 d compression group were similar to that in normal control group (with P values above 0.05), and the expressions of phosphorylated NF-κB in skin tissue of rats in 5 d compression group and 7 d compression group were significantly higher than that in normal control group (P<0.05 or P<0.01). The high expression of MMP-2 and reduction of collagen induced by inflammatory reaction mediated by the high expression of TNF-α in local skin tissue of pressure ulcer of rats may be one of the important reasons for the formation of pressure ulcer.

Mammographic compression in Asian women.

PubMed

Lau, Susie; Abdul Aziz, Yang Faridah; Ng, Kwan Hoong

2017-01-01

To investigate: (1) the variability of mammographic compression parameters amongst Asian women; and (2) the effects of reducing compression force on image quality and mean glandular dose (MGD) in Asian women based on phantom study. We retrospectively collected 15818 raw digital mammograms from 3772 Asian women aged 35-80 years who underwent screening or diagnostic mammography between Jan 2012 and Dec 2014 at our center. The mammograms were processed using a volumetric breast density (VBD) measurement software (Volpara) to assess compression force, compression pressure, compressed breast thickness (CBT), breast volume, VBD and MGD against breast contact area. The effects of reducing compression force on image quality and MGD were also evaluated based on measurement obtained from 105 Asian women, as well as using the RMI156 Mammographic Accreditation Phantom and polymethyl methacrylate (PMMA) slabs. Compression force, compression pressure, CBT, breast volume, VBD and MGD correlated significantly with breast contact area (p<0.0001). Compression parameters including compression force, compression pressure, CBT and breast contact area were widely variable between [relative standard deviation (RSD)≥21.0%] and within (p<0.0001) Asian women. The median compression force should be about 8.1 daN compared to the current 12.0 daN. Decreasing compression force from 12.0 daN to 9.0 daN increased CBT by 3.3±1.4 mm, MGD by 6.2-11.0%, and caused no significant effects on image quality (p>0.05). Force-standardized protocol led to widely variable compression parameters in Asian women. Based on phantom study, it is feasible to reduce compression force up to 32.5% with minimal effects on image quality and MGD.

Real-time compression of raw computed tomography data: technology, architecture, and benefits

NASA Astrophysics Data System (ADS)

Wegener, Albert; Chandra, Naveen; Ling, Yi; Senzig, Robert; Herfkens, Robert

2009-02-01

Compression of computed tomography (CT) projection samples reduces slip ring and disk drive costs. A lowcomplexity, CT-optimized compression algorithm called Prism CTTM achieves at least 1.59:1 and up to 2.75:1 lossless compression on twenty-six CT projection data sets. We compare the lossless compression performance of Prism CT to alternative lossless coders, including Lempel-Ziv, Golomb-Rice, and Huffman coders using representative CT data sets. Prism CT provides the best mean lossless compression ratio of 1.95:1 on the representative data set. Prism CT compression can be integrated into existing slip rings using a single FPGA. Prism CT decompression operates at 100 Msamp/sec using one core of a dual-core Xeon CPU. We describe a methodology to evaluate the effects of lossy compression on image quality to achieve even higher compression ratios. We conclude that lossless compression of raw CT signals provides significant cost savings and performance improvements for slip rings and disk drive subsystems in all CT machines. Lossy compression should be considered in future CT data acquisition subsystems because it provides even more system benefits above lossless compression while achieving transparent diagnostic image quality. This result is demonstrated on a limited dataset using appropriately selected compression ratios and an experienced radiologist.

Prediction of compression-induced image interpretability degradation

NASA Astrophysics Data System (ADS)

Blasch, Erik; Chen, Hua-Mei; Irvine, John M.; Wang, Zhonghai; Chen, Genshe; Nagy, James; Scott, Stephen

2018-04-01

Image compression is an important component in modern imaging systems as the volume of the raw data collected is increasing. To reduce the volume of data while collecting imagery useful for analysis, choosing the appropriate image compression method is desired. Lossless compression is able to preserve all the information, but it has limited reduction power. On the other hand, lossy compression, which may result in very high compression ratios, suffers from information loss. We model the compression-induced information loss in terms of the National Imagery Interpretability Rating Scale or NIIRS. NIIRS is a user-based quantification of image interpretability widely adopted by the Geographic Information System community. Specifically, we present the Compression Degradation Image Function Index (CoDIFI) framework that predicts the NIIRS degradation (i.e., a decrease of NIIRS level) for a given compression setting. The CoDIFI-NIIRS framework enables a user to broker the maximum compression setting while maintaining a specified NIIRS rating.

Fundamental study of compression for movie files of coronary angiography

NASA Astrophysics Data System (ADS)

Ando, Takekazu; Tsuchiya, Yuichiro; Kodera, Yoshie

2005-04-01

When network distribution of movie files was considered as reference, it could be useful that the lossy compression movie files which has small file size. We chouse three kinds of coronary stricture movies with different moving speed as an examination object; heart rate of slow, normal and fast movies. The movies of MPEG-1, DivX5.11, WMV9 (Windows Media Video 9), and WMV9-VCM (Windows Media Video 9-Video Compression Manager) were made from three kinds of AVI format movies with different moving speeds. Five kinds of movies that are four kinds of compression movies and non-compression AVI instead of the DICOM format were evaluated by Thurstone's method. The Evaluation factors of movies were determined as "sharpness, granularity, contrast, and comprehensive evaluation." In the virtual bradycardia movie, AVI was the best evaluation at all evaluation factors except the granularity. In the virtual normal movie, an excellent compression technique is different in all evaluation factors. In the virtual tachycardia movie, MPEG-1 was the best evaluation at all evaluation factors expects the contrast. There is a good compression form depending on the speed of movies because of the difference of compression algorithm. It is thought that it is an influence by the difference of the compression between frames. The compression algorithm for movie has the compression between the frames and the intra-frame compression. As the compression algorithm give the different influence to image by each compression method, it is necessary to examine the relation of the compression algorithm and our results.

Effect of the rate of chest compression familiarised in previous training on the depth of chest compression during metronome-guided cardiopulmonary resuscitation: a randomised crossover trial.

PubMed

Bae, Jinkun; Chung, Tae Nyoung; Je, Sang Mo

2016-02-12

To assess how the quality of metronome-guided cardiopulmonary resuscitation (CPR) was affected by the chest compression rate familiarised by training before the performance and to determine a possible mechanism for any effect shown. Prospective crossover trial of a simulated, one-person, chest-compression-only CPR. Participants were recruited from a medical school and two paramedic schools of South Korea. 42 senior students of a medical school and two paramedic schools were enrolled but five dropped out due to physical restraints. Senior medical and paramedic students performed 1 min of metronome-guided CPR with chest compressions only at a speed of 120 compressions/min after training for chest compression with three different rates (100, 120 and 140 compressions/min). Friedman's test was used to compare average compression depths based on the different rates used during training. Average compression depths were significantly different according to the rate used in training (p<0.001). A post hoc analysis showed that average compression depths were significantly different between trials after training at a speed of 100 compressions/min and those at speeds of 120 and 140 compressions/min (both p<0.001). The depth of chest compression during metronome-guided CPR is affected by the relative difference between the rate of metronome guidance and the chest compression rate practised in previous training. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

Digital compression algorithms for HDTV transmission

NASA Technical Reports Server (NTRS)

Adkins, Kenneth C.; Shalkhauser, Mary JO; Bibyk, Steven B.

1990-01-01

Digital compression of video images is a possible avenue for high definition television (HDTV) transmission. Compression needs to be optimized while picture quality remains high. Two techniques for compression the digital images are explained and comparisons are drawn between the human vision system and artificial compression techniques. Suggestions for improving compression algorithms through the use of neural and analog circuitry are given.

Sensitivity Analysis in RIPless Compressed Sensing

DTIC Science & Technology

2014-10-01

SECURITY CLASSIFICATION OF: The compressive sensing framework finds a wide range of applications in signal processing and analysis. Within this...Analysis of Compressive Sensing Solutions Report Title The compressive sensing framework finds a wide range of applications in signal processing and...compressed sensing. More specifically, we show that in a noiseless and RIP-less setting [11], the recovery process of a compressed sensing framework is

Compression device for feeding a waste material to a reactor

DOEpatents

Williams, Paul M.; Faller, Kenneth M.; Bauer, Edward J.

2001-08-21

A compression device for feeding a waste material to a reactor includes a waste material feed assembly having a hopper, a supply tube and a compression tube. Each of the supply and compression tubes includes feed-inlet and feed-outlet ends. A feed-discharge valve assembly is located between the feed-outlet end of the compression tube and the reactor. A feed auger-screw extends axially in the supply tube between the feed-inlet and feed-outlet ends thereof. A compression auger-screw extends axially in the compression tube between the feed-inlet and feed-outlet ends thereof. The compression tube is sloped downwardly towards the reactor to drain fluid from the waste material to the reactor and is oriented at generally right angle to the supply tube such that the feed-outlet end of the supply tube is adjacent to the feed-inlet end of the compression tube. A programmable logic controller is provided for controlling the rotational speed of the feed and compression auger-screws for selectively varying the compression of the waste material and for overcoming jamming conditions within either the supply tube or the compression tube.

Quality of reconstruction of compressed off-axis digital holograms by frequency filtering and wavelets.

PubMed

Cheremkhin, Pavel A; Kurbatova, Ekaterina A

2018-01-01

Compression of digital holograms can significantly help with the storage of objects and data in 2D and 3D form, its transmission, and its reconstruction. Compression of standard images by methods based on wavelets allows high compression ratios (up to 20-50 times) with minimum losses of quality. In the case of digital holograms, application of wavelets directly does not allow high values of compression to be obtained. However, additional preprocessing and postprocessing can afford significant compression of holograms and the acceptable quality of reconstructed images. In this paper application of wavelet transforms for compression of off-axis digital holograms are considered. The combined technique based on zero- and twin-order elimination, wavelet compression of the amplitude and phase components of the obtained Fourier spectrum, and further additional compression of wavelet coefficients by thresholding and quantization is considered. Numerical experiments on reconstruction of images from the compressed holograms are performed. The comparative analysis of applicability of various wavelets and methods of additional compression of wavelet coefficients is performed. Optimum parameters of compression of holograms by the methods can be estimated. Sizes of holographic information were decreased up to 190 times.

Report from the 2013 meeting of the International Compression Club on advances and challenges of compression therapy.

PubMed

Delos Reyes, Arthur P; Partsch, Hugo; Mosti, Giovanni; Obi, Andrea; Lurie, Fedor

2014-10-01

The International Compression Club, a collaboration of medical experts and industry representatives, was founded in 2005 to develop consensus reports and recommendations regarding the use of compression therapy in the treatment of acute and chronic vascular disease. During the recent meeting of the International Compression Club, member presentations were focused on the clinical application of intermittent pneumatic compression in different disease scenarios as well as on the use of inelastic and short stretch compression therapy. In addition, several new compression devices and systems were introduced by industry representatives. This article summarizes the presentations and subsequent discussions and provides a description of the new compression therapies presented. Copyright © 2014 Society for Vascular Surgery. Published by Elsevier Inc. All rights reserved.