Science.gov

Sample records for hepa wash treatment

  1. Nasal Wash Treatment

    MedlinePlus

    ... Make the nasal wash solution. Do not use tap water for the nasal wash (unless boiled or filtered ... water. You may use: Distilled water Sterilized water Tap water that has been boiled for 1 minute (at ...

  2. The Treatment Procedure for a Volume Reduction of the Spent HEPA Filters in KAERI

    SciTech Connect

    Ji, Y.Y.; Hong, D.S.; Kang, I.S.; Shon, J.S.

    2008-07-01

    Spent filter wastes of about 2,200 units have been stored in the radioactive waste storage facility of the Korea Atomic Energy Research Institute since its operation. Among these spent filter wastes, a HEPA filter account for about 95 %. All these HEPA filter wastes generated at KAERI have been stored inside a poly bag in accordance with the original form without any treatment of them. Therefore, in order to secure a space in a radioactive waste storage facility approaching its saturation, it is necessary to treat them by a compaction in view of a radioactive waste treatment and storage, and finally to repack the compacted spent filters into a regular drum for sending them to a final disposal site. To do that, the spent HEPA filter wastes were classified according to their generation facility, their generation date and their surface dose rate by investigating the inventory of them. And also, a nuclide assessment of them was conducted by taking a representative sample at the spot of a high dose rate at the intake surface and the outlet surface of a spent HEPA filter without a dismantlement, before compacting them. At present, for the spent HEPA filter wastes after a radionuclide assessment, a compaction treatment of them is now being conducted by using the shaping and compacting equipment developed at KAERI. Thus, to put a HEPA filter with a hexahedral form of a 610(W) x 610(H) x 305(T) mm into a regular drum (DOT-17H) with an inner diameter of about 572 mm, a columnar shaping with a capacity of 15 tons was conducted. From this shaping, a shaped HEPA filter waste with a diameter of about 500 mm was directly put into a regular drum. And then, the compaction treatment of a shaped HEPA filter with a capacity of about 60 tons was conducted by vertically compacting it. As a result, a volume reduction rate of a spent HEPA filter waste by a shaping and compacting of it accounted for about 1/8 when compared to its original form. (authors)

  3. HEPA filter jointer

    SciTech Connect

    Hill, D.; Martinez, H.E.

    1998-02-01

    A HEPA filter jointer system was created to remove nitrate contaminated wood from the wooden frames of HEPA filters that are stored at the Rocky Flats Plant. A commercial jointer was chosen to remove the nitrated wood. The chips from the wood removal process are in the right form for caustic washing. The jointer was automated for safety and ease of operation. The HEPA filters are prepared for jointing by countersinking the nails with a modified air hammer. The equipment, computer program, and tests are described in this report.

  4. Durable titania films for solar treatment of biomethanated spent wash

    NASA Astrophysics Data System (ADS)

    Akbarzadeh, Rokhsareh; S. Ghole, Vikram; Javadpour, Sirus

    2016-10-01

    The use of TiO2 films for treatment of biomethanated spent wash is reported. The films of TiO2 were formed and photocatalytic performance of the prepared films in degradation of methylene blue and biomethanated spent wash were studied. Photocatalytic use of these films was found to be effective for degradation of biomethanated spent wash. The photocatalyst was used up for 20 cycles without significant reduction in activities showing long life of the catalyst.

  5. HEPA Help

    ERIC Educational Resources Information Center

    Rathey, Allen

    2006-01-01

    Poor indoor air quality in school facilities can detract from the health and productivity of students, teachers and other employees. Asthma--often triggered or aggravated by dust--is the No. 1 cause of chronic absenteeism in schools. Using vacuum cleaners equipped with high-efficiency particulate air (HEPA) filters to clean education institutions…

  6. Aging assessment of nuclear air-treatment system HEPA filters and adsorbers. Volume 1, Phase 1

    SciTech Connect

    Winegardner, W.K.

    1993-08-01

    A Phase I aging assessment of high-efficiency particulate air (HEPA) filters and activated carbon gas adsorption units (adsorbers) was performed by the Pacific Northwest Laboratory (PNL) as part of the US Nuclear Regulatory Commission`s (NRC) Nuclear Plant Aging Research (NPAR) Program. Information concerning design features; failure experience; aging mechanisms, effects, and stressors; and surveillance and monitoring methods for these key air-treatment system components was compiled. Over 1100 failures, or 12 percent of the filter installations, were reported as part of a Department of Energy (DOE) survey. Investigators from other national laboratories have suggested that aging effects could have contributed to over 80 percent of these failures. Tensile strength tests on aged filter media specimens indicated a decrease in strength. Filter aging mechanisms range from those associated with particle loading to reactions that alter properties of sealants and gaskets. Low radioiodine decontamination factors associated with the Three Mile Island (TMI) accident were attributed to the premature aging of the carbon in the adsorbers. Mechanisms that can lead to impaired adsorber performance include oxidation as well as the loss of potentially available active sites as a result of the adsorption of pollutants. Stressors include heat, moisture, radiation, and airborne particles and contaminants.

  7. Treatment of tunnel wash water and implications for its disposal.

    PubMed

    Hallberg, M; Renman, G; Byman, L; Svenstam, G; Norling, M

    2014-01-01

    The use of road tunnels in urban areas creates water pollution problems, since the tunnels must be frequently cleaned for traffic safety reasons. The washing generates extensive volumes of highly polluted water, for example, more than fivefold higher concentrations of suspended solids compared to highway runoff. The pollutants in the wash water have an affinity for particulate material, so sedimentation should be a viable treatment option. In this study, 12 in situ sedimentation trials were carried out on tunnel wash water, with and without addition of chemical flocculent. Initial suspended solids concentration ranged from 804 to 9,690 mg/L. With sedimentation times of less than 24 hours and use of a chemical flocculent, it was possible to reach low concentrations of suspended solids (<15 mg/L), PAH (<0.1 μg/L), As (<1.0 μg/L), Cd (<0.05 μg/L), Hg (<0.02 μg/L), Fe (<200 μg/L), Ni (<8 μg/L), Pb (<0.5 μg/L), Zn (<60 μg/L) and Cr (<8 μg/L). Acute Microtox(®) toxicity, mainly attributed to detergents used for the tunnel wash, decreased significantly at low suspended solids concentrations after sedimentation using a flocculent. The tunnel wash water did not inhibit nitrification. The treated water should be suitable for discharge into recipient waters or a wastewater treatment plant.

  8. Development of a Pulp Process Treating Contaminated HEPA Filters (III)

    SciTech Connect

    Hu, J. S.; Ramer, J.; Argyle, M. D.; Demmer, R. L.

    2002-02-28

    The Pulp Process (PP) Treatment option was conceived as a replacement for the current Filter Leaching System (FLS). The FLS has operated at the Idaho Nuclear Technology and Engineering Center of the Idaho National Engineering and Environmental Laboratory since 1995 to treat radioactive, mixed waste HEPA filters. In recent years, the FLS has exhibited difficulty in removing mercury from the HEPA filters as the concentration of mercury in the spent HEPA filters has increased. The FLS leaches and washes the whole filter without any preparation or modification. The filter media and the trapped calcine particles are confined in a heavy filter housing that contributes to poor mixing zones around the edges of the filter, low media permeability, channeling of the liquid through cracks and tears in the filter media, and liquid retention between leach and rinse cycles. In the PP, the filter media and the trapped calcine particles are separated from the filter housing and treated as a pulp, taking advantage of improved contact with the leach solution that cannot be achieved when the media is still in the HEPA filter housing. In addition to removing the mercury more effectively, the PP generates less volume of liquid waste, requires a shorter leach cycle time, and possesses the versatility for treating filters of different sizes. A series of tests have been performed in the laboratory to demonstrate the advantages of the PP concept. These tests compare the PP with the FLS under controlled conditions that simulate the current operating parameters. A prior study using blended feed, a mixture of shredded clean HEPA filter media and non-radioactive calcine particles, indicated that the PP would significantly increases the calcine dissolution percentages. In this study, hazardous-metal contaminated HEPA filter media was studied. The results of side-by-side tests indicated that the PP increased the mercury removal percentage by 80% and might be a solution to the mercury removal

  9. HEPA filter dissolution process

    DOEpatents

    Brewer, K.N.; Murphy, J.A.

    1994-02-22

    A process is described for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal. 4 figures.

  10. Hepa filter dissolution process

    DOEpatents

    Brewer, Ken N.; Murphy, James A.

    1994-01-01

    A process for dissolution of spent high efficiency particulate air (HEPA) filters and then combining the complexed filter solution with other radioactive wastes prior to calcining the mixed and blended waste feed. The process is an alternate to a prior method of acid leaching the spent filters which is an inefficient method of treating spent HEPA filters for disposal.

  11. Characterising nutrients wash-off for effective urban stormwater treatment design.

    PubMed

    Miguntanna, Nandika P; Liu, An; Egodawatta, Prasanna; Goonetilleke, Ashantha

    2013-05-15

    This paper characterises nitrogen and phosphorus wash-off processes on urban road surfaces to create fundamental knowledge to strengthen stormwater treatment design. The study outcomes confirmed that the composition of initially available nutrients in terms of their physical association with solids and chemical speciation determines the wash-off characteristics. Nitrogen and phosphorus wash-off processes are independent of land use, but there are notable differences. Nitrogen wash-off is a "source limiting" process while phosphorus wash-off is "transport limiting". Additionally, a clear separation between nitrogen and phosphorus wash-off processes based on dissolved and particulate forms confirmed that the common approach of replicating nutrients wash-off based on solids wash-off could lead to misleading outcomes particularly in the case of nitrogen. Nitrogen is present primarily in dissolved and organic form and readily removed even by low intensity rainfall events, which is an important consideration for nitrogen removal targeted treatment design. In the case of phosphorus, phosphate constitutes the primary species in wash-off for the particle size fraction <75 μm, while other species are predominant in particle size range >75 μm. This means that phosphorus removal targeted treatment design should consider both phosphorus speciation as well as particle size.

  12. Treatment of car wash wastewater by UF membranes

    NASA Astrophysics Data System (ADS)

    Istirokhatun, Titik; Destianti, Puti; Hargianintya, Adenira; Oktiawan, Wiharyanto; Susanto, Heru

    2015-12-01

    The existence of car wash service facilitates car owners to remove dirt and grime from their vehicles. However, the dirt washed off vehicles as well as the cleaning materials themselves may be harmful to the environment if they are not properly managed and discharged. Many technologies have been proposed to treat car wash wastewater such as coagulation flocculation, tricking filter and flocculation-flotation. Nevertheless, these technologies have low efficiency to eliminate oil and small organic compounds. Ultrafiltration (UF) membranes were used in this study to treat car wash wastewater. This study investigated the performance of UF membranes under various pressures to remove COD, oil and grease, and also turbidity from car wash waste water. The membrane performance was examined by investigation of permeate flux and membrane rejection. The results meet the standard of environmental regulation and it is possible to be reused. The highest rejection was shown by PES10 (polyethersulfone 10 kDa) in 1 bar operation with complete rejection for both turbidity and oil and grace and 95% rejection for COD.

  13. A Novel HEPA Filter Encapsulation Process

    SciTech Connect

    Gates-Anderson, D.; Kidd, S.; Attebery, R.; Belue, T.; Bowers, J.; Rogers, H.

    2002-02-28

    Waste management engineers at Lawrence Livermore National Laboratory have developed an innovative process for the treatment of contaminated HEPA filters. The In Situ Stabilization and Filter Encapsulation (IS SAFE) Process provides several advantages over existing HEPA filter treatment processes. Treatment is accomplished by filling a spent HEPA filter with a low viscosity resin that cures to form a solid monolith. Once a solid monolith has been formed, the HEPA filter has been transformed in two ways: (1) worker hazards/risks associated with handling the filter are eliminated and (2) the in situ encapsulated filter meets LDR requirements and can be disposed of in a permitted landfill. A patent has been filed for this process. The IS SAFE process will be applicable to hazardous, mixed, and low level radioactively contaminated spent filters. Spent HEPA filters are prepared for processing by attaching vacuum fittings to the top and bottom openings of the filter. These fittings are used to attach the filter to a vacuum system comprised of a vacuum pump, vacuum gauge, resin reservoir and associated tubing and fittings. Resin is delivered to the filter in a controlled fashion. The total processing time for a 50-cubic feet per minute (cfm) filter is approximately 25 minutes. The resin filled HEPA filter is allowed to cure at ambient temperature and pressure for at least 24 hours. The final product is a solid monolith with less that 0.1 percent by volume of void space and 100 percent of the filter media coated with resin. Proof of concept studies have been completed using 50, 135, and 1000 cfm closed face HEPA filters. During these studies, we were able to develop and demonstrate a resin delivery process that yielded a final product that was suitable for in ground disposal. Additional adaptations of the process may be required for specific application, but the process equipment, supplies, and methodology have been fully established for contact handled, closed face

  14. INEEL HEPA Filter Leach System: A Mixed Waste Solution

    SciTech Connect

    Argyle, Mark Don; Demmer, Ricky Lynn; Archibald, Kip Ernest; Brewer, Ken Neal; Pierson, Kenneth Alan; Shackelford, Kimberlee Rene; Kline, Kelli Suzanne

    1999-03-01

    Calciner operations and the fuel dissolution process at the Idaho National Engineering and Environmental Laboratory have generated many mixed waste high-efficiency particulate air (HEPA) filters. The HEPA Filter Leach System located at the Idaho Nuclear Technology and Engineering Center lowers radiation contamination levels and reduces cadmium, chromium, and mercury concentrations on spent HEPA filter media to below disposal limits set by the Resource Conservation and Recovery Act (RCRA). The treated HEPA filters are disposed as low-level radioactive waste. The technical basis for the existing system was established and optimized in initial studies using simulants in 1992. The treatment concept was validated for EPA approval in 1994 by leaching six New Waste Calcining Facility spent HEPA filters. Post-leach filter media sampling results for all six filters showed that both hazardous and radiological constituent levels were reduced so the filters could be disposed of as low-level radioactive waste. Since the validation tests the HEPA Filter Leach System has processed 78 filters in 1997 and 1998. The Idaho National Engineering and Environmental Laboratory HEPA Filter Leach System is the only mixed waste HEPA treatment system in the DOE complex. This process is of interest to many of the other DOE facilities and commercial companies that have generated mixed waste HEPA filters but currently do not have a treatment option available.

  15. INEEL HEPA Filter Leach System: A Mixed Waste Solution

    SciTech Connect

    K. Archibald; K. Brewer; K. Kline; K. Pierson; K. Shackelford; M. Argyle; R. Demmer

    1999-02-01

    Calciner operations and the fuel dissolution process at the Idaho National Engineering and Environmental Laboratory have generated many mixed waste high-efficiency particulate air (HEPA)filters. The HEPA Filter Leach System located at the Idaho Nuclear Technology and Engineering Center lowers radiation contamination levels and reduces cadmium, chromium, and mercury concentrations on spent HEPA filter media to below disposal limits set by the Resource Conservation and Recovery Act (RCRA). The treated HEPA filters are disposed as low-level radioactive waste. The technical basis for the existing system was established and optimized in initial studies using simulants in 1992. The treatment concept was validated for EPA approval in 1994 by leaching six New Waste Calcining Facility spent HEPA filters. Post-leach filter media sampling results for all six filters showed that both hazardous and radiological constituent levels were reduced so the filters could be disposed of as low-level radioactive waste. Since the validation tests the HEPA Filter Leach System has processed 78 filters in 1997 and 1998. The Idaho National Engineering and Environmental Laboratory HEPA Filter Leach System is the only mixed waste HEPA treatment system in the DOE complex. This process is of interest to many of the other DOE facilities and commercial companies that have generated mixed waste HEPA filters but currently do not have a treatment option available.

  16. HEPA air filter (image)

    MedlinePlus

    ... pet dander and other irritating allergens from the air. Along with other methods to reduce allergens, such ... controlling the amount of allergens circulating in the air. HEPA filters can be found in most air ...

  17. ANAEROBIC TREATMENT OF SOIL WASH FLUIDS FROM A WOOD PRESERVING SITE

    EPA Science Inventory

    An integrated system has been developed to remediate sols contaminated with pentachlorophenol (PCP) and polycyclic aromatic hydrocarbons (PAHs). This system involves the coupling of two treatment technologies, soil solvent washing and anaerobic biotreatment of the extract. Specif...

  18. Performance of a Small-scale Treatment Wetland for Treatment of Landscaping Wash Water

    NASA Astrophysics Data System (ADS)

    Thompson, R. J.; Fayed, E.; Fish, W.

    2011-12-01

    A large number of lawn mowers and related equipment must be cleaned each day by commercial landscaping operations and state and local highway maintenance crews. Washing these devices produces wastewater that contains high amounts of organic matter and potentially problematic nutrients, as well as oil and grease and other chemicals and metals that come from the machinery itself. Dirty water washes off the mowers, flows off the pavement and into nearby storm drains without any kind of treatment. A better idea would be to collect such wastewater, retain it in an appropriate catchment such as an engineered wetland where natural processes could break down any pollutants in the wash water, and allow the water to naturally evaporate or percolate into the soil where it could recharge ground water resources safely. This research examines the performance of a small-scale treatment wetland tailored to remove nitrogen from landscaping wash water by incorporating both aerobic and anaerobic phases. Contaminants are analyzed through physical and chemical methods. Both methods involve collection of samples, followed by standardized, validated analytical laboratory tests for measuring total solids, total kjeldahl nitrogen, nitrates, total and dissolved phosphorus, COD, BOD, oil and grease, and metals (Zn and Cu). High levels of total solids, total kjeldahl nitrogen, nitrates, total and dissolved phosphorus, COD, BOD, oil and grease are found. Zinc and copper levels are low. Wetland treatment removes 99% total solids, 77% total kjeldahl nitrogen, 100% nitrates, 94% total phosphorus, 86% dissolved phosphorus, 94% COD, 97% BOD, and 76% oil and grease. The results will be a critical step towards developing a sustainable low-energy system for treating such wastewater that could be used by private landscaping companies and government agencies.

  19. Efficient remediation of pentachlorophenol contaminated soil with tetrapolyphosphate washing and subsequent ZVI/Air treatment.

    PubMed

    Cao, Menghua; Wang, Li; Ai, Zhihui; Zhang, Lizhi

    2015-07-15

    In this study, we demonstrate that pentachlorophenol contaminated soil can be efficiently remediated with tetrapolyphosphate washing and subsequent zerovalent iron (ZVI)/Air treatment. 2 mmol L(-1) of tetrapolyphosphate could wash away 52.8% of pentachlorophenol (PCP) at pH 7.0 and 84.2% of pentachlorophenol at pH 11.0 from contaminated soil owing to the promotion effect of tetrapolyphosphate on the soil matrix dispersion and the subsequent solubilization of pentachlorophenol. More importantly, tetrapolyphosphate ions remained in the washing effluent could greatly enhance the molecular oxygen activation by ZVI to oxidize the desorbed PCP without any pH adjustment, and also avoid the competitive consumption of reactive oxygen species, as caused by the common organic surfactants in the washing effluent. Therefore, 85.1% of pentachlorophenol could be aerobically removed from the washing effluent by merely using 5 g L(-1) of ZVI. We also interestingly found that the dissolved iron ions released from the soil could enhance the oxidation of pentachlorophenol in the washing effluent, but the dissolved organic matter had the opposite effect. This study suggests the coupling tetrapolyphosphate washing and subsequent ZVI/Air treatment is an optional approach to remediate pentachlorophenol contaminated soil in view of its low cost and environmental benign.

  20. HEPA Filter Vulnerability Assessment

    SciTech Connect

    GUSTAVSON, R.D.

    2000-05-11

    This assessment of High Efficiency Particulate Air (HEPA) filter vulnerability was requested by the USDOE Office of River Protection (ORP) to satisfy a DOE-HQ directive to evaluate the effect of filter degradation on the facility authorization basis assumptions. Within the scope of this assessment are ventilation system HEPA filters that are classified as Safety-Class (SC) or Safety-Significant (SS) components that perform an accident mitigation function. The objective of the assessment is to verify whether HEPA filters that perform a safety function during an accident are likely to perform as intended to limit release of hazardous or radioactive materials, considering factors that could degrade the filters. Filter degradation factors considered include aging, wetting of filters, exposure to high temperature, exposure to corrosive or reactive chemicals, and exposure to radiation. Screening and evaluation criteria were developed by a site-wide group of HVAC engineers and HEPA filter experts from published empirical data. For River Protection Project (RPP) filters, the only degradation factor that exceeded the screening threshold was for filter aging. Subsequent evaluation of the effect of filter aging on the filter strength was conducted, and the results were compared with required performance to meet the conditions assumed in the RPP Authorization Basis (AB). It was found that the reduction in filter strength due to aging does not affect the filter performance requirements as specified in the AB. A portion of the HEPA filter vulnerability assessment is being conducted by the ORP and is not part of the scope of this study. The ORP is conducting an assessment of the existing policies and programs relating to maintenance, testing, and change-out of HEPA filters used for SC/SS service. This document presents the results of a HEPA filter vulnerability assessment conducted for the River protection project as requested by the DOE Office of River Protection.

  1. DOE HEPA filter test program

    SciTech Connect

    1998-05-01

    This standard establishes essential elements of a Department of Energy (DOE) program for testing HEPA filters to be installed in DOE nuclear facilities or used in DOE-contracted activities. A key element is the testing of HEPA filters for performance at a DOE Filter Test Facility (FTF) prior to installation. Other key elements are (1) providing for a DOE HEPA filter procurement program, and (2) verifying that HEPA filters to be installed in nuclear facilities appear on a Qualified Products List (QPL).

  2. Contextualizing Hepatocyte Functionality of Cryopreserved HepaRG Cell Cultures.

    PubMed

    Jackson, Jonathan P; Li, Linhou; Chamberlain, Erica D; Wang, Hongbing; Ferguson, Stephen S

    2016-09-01

    Over the last decade HepaRG cells have emerged as a promising alternative to primary human hepatocytes (PHH) and have been featured in over 300 research publications. Most of these reports employed freshly differentiated HepaRG cells that require time-consuming culture (∼28 days) for full differentiation. Recently, a cryopreserved, predifferentiated format of HepaRG cells (termed here "cryo-HepaRG") has emerged as a new model that improves global availability and experimental flexibility; however, it is largely unknown whether HepaRG cells in this format fully retain their hepatic characteristics. Therefore, we systematically investigated the hepatocyte functionality of cryo-HepaRG cultures in context with the range of interindividual variation observed with PHH in both sandwich-culture and suspension formats. These evaluations uncovered a novel adaptation period for the cryo-HepaRG format and demonstrated the impact of extracellular matrix on cryo-HepaRG functionality. Pharmacologically important drug-metabolizing alleles were genotyped in HepaRG cells and poor metabolizer alleles for CYP2D6, CYP2C9, and CYP3A5 were identified and consistent with higher frequency alleles found in individuals of Caucasian decent. We observed liver enzyme inducibility with aryl hydrocarbon receptor, constitutive androstane receptor (CAR), and pregnane X receptor activators comparable to that of sandwich-cultured PHH. Finally, we show for the first time that cryo-HepaRG supports proper CAR cytosolic sequestration and translocation to hepatocyte nuclei in response to phenobarbital treatment. Taken together, these data reveal important considerations for the use of this cell model and demonstrate that cryo-HepaRG are suitable for metabolism and toxicology screening.

  3. HEPA filter encapsulation

    DOEpatents

    Gates-Anderson, Dianne D.; Kidd, Scott D.; Bowers, John S.; Attebery, Ronald W.

    2003-01-01

    A low viscosity resin is delivered into a spent HEPA filter or other waste. The resin is introduced into the filter or other waste using a vacuum to assist in the mass transfer of the resin through the filter media or other waste.

  4. TECHNOLOGY EVALUATION REPORT: BIOTROL SOIL WASHING SYSTEM FOR TREATMENT OF A WOOD PRESERVING SITE - VOLUME I

    EPA Science Inventory

    The report presents and evaluates the extensive database from the SITE Program demonstration at the MacGillis and Gibbs wood treatment facility in New Brighton, MN. Soil washing and segregation, biotreatment of contaminated process water, and biodegradation of a slurry of the con...

  5. BIOTROL SOIL WASHING SYSTEM FOR TREATMENT OF A WOOD PRESERVING SITE - APPLICATIONS ANALYSIS REPORT

    EPA Science Inventory

    The report analyzes the results of the SITE Program demonstration of BioTrol's Soil Washing System at the MacGillis & Gibbs wood treatment facility in New Brighton, MN. The contaminants of primary interest are pentachlorophenol (penta) and polynuclear aromatic hydrocarbons (PAHs)...

  6. Assessment of seasonal variation for air pollutant accumulation by Zizyphus tree under washing treatment.

    PubMed

    Shaheen, Mohamed Abdulraheem; El-Nakhlawy, Fathy Saad; Almehmadi, Fahd Mosallam; Ihsan, Muhammad Zahid; Al-Shareef, Abdulmohsin Rajeh

    2016-06-01

    A field study was carried out near Jeddah Industrial Zone to estimate the leaf impairment, physiological disorders, and air pollutant accumulation potential of Ziziphus tree. The experiment was triplicated in RCBD design with factorial arrangement having seasonality as the main plot and washing as subplot treatments along with the control. Accumulation of heavy metals and micronutrients in plant foliage varied significantly under the influence of seasons and washing treatments. The maximum accumulation of cadmium, chromium, nickel, and lead were perceived in summer season while the minimum was observed in winter. Contrarily, a greater acquisition of iron, copper, zinc, and manganese was observed in autumn. Washing significantly reduced the accumulation of Cd, Cr, Ni, and Pb by 58, 90, 80, and 96 %, while Fe, Cu, Zn, and Mn by 89, 37, 60, and 93 %, respectively. Leaf protein and nitrogen content illustrated a greater adjustment for pollutants by presenting a minimum variation (14-18 % and 2-3 %) to seasonality. In contrast, leaf area and stomatal aperture were significantly disturbed and resulted in minimum recovery under washing. Correlation analysis revealed a stronger negative interaction of heavy metal accumulation to leaf features while non-significant interaction was perceived for microelements. In conclusion, planting of Ziziphus trees along industrial areas may impede potential threats of toxic pollutants to human and ecosystem. PMID:27170355

  7. Remediation of arsenic contaminated soil by coupling oxalate washing with subsequent ZVI/Air treatment.

    PubMed

    Cao, Menghua; Ye, Yuanyao; Chen, Jing; Lu, Xiaohua

    2016-02-01

    The application of a novel coupled process with oxalate washing and subsequent zero-valent iron (ZVI)/Air treatment for remediation of arsenic contaminated soil was investigated in the present study. Oxalate is biodegradable and widely present in the environment. With addition of 0.1 mol L(-1) oxalate under circumneutral condition, 83.7% and 52.6% of arsenic could be removed from a spiked kaolin and an actual contaminated soil respectively. Much more oxalate adsorption on the actual soil was attributed to the higher soil organic matter and clay content. Interestingly, oxalate retained in the washing effluent could act as an organic ligand to promote the oxidation efficiency of ZVI/Air at near neutral pH. Compared with the absence of oxalate, much more As(III) was oxidized. Arsenic was effectively adsorbed on iron (hydr)oxides as the consumption of oxalate and the increase of pH value. For the actual soil washing effluent, about 94.9% of total arsenic was removed after 120 min's treatment without pH adjustment. It has been demonstrated that As(V) was the dominant arsenic speciation adsorbed on iron (hydr)oxides. This study provides a promising alternative for remediation of arsenic contaminated soil in view of its low cost and environmental benign. PMID:26476769

  8. Remediation of arsenic contaminated soil by coupling oxalate washing with subsequent ZVI/Air treatment.

    PubMed

    Cao, Menghua; Ye, Yuanyao; Chen, Jing; Lu, Xiaohua

    2016-02-01

    The application of a novel coupled process with oxalate washing and subsequent zero-valent iron (ZVI)/Air treatment for remediation of arsenic contaminated soil was investigated in the present study. Oxalate is biodegradable and widely present in the environment. With addition of 0.1 mol L(-1) oxalate under circumneutral condition, 83.7% and 52.6% of arsenic could be removed from a spiked kaolin and an actual contaminated soil respectively. Much more oxalate adsorption on the actual soil was attributed to the higher soil organic matter and clay content. Interestingly, oxalate retained in the washing effluent could act as an organic ligand to promote the oxidation efficiency of ZVI/Air at near neutral pH. Compared with the absence of oxalate, much more As(III) was oxidized. Arsenic was effectively adsorbed on iron (hydr)oxides as the consumption of oxalate and the increase of pH value. For the actual soil washing effluent, about 94.9% of total arsenic was removed after 120 min's treatment without pH adjustment. It has been demonstrated that As(V) was the dominant arsenic speciation adsorbed on iron (hydr)oxides. This study provides a promising alternative for remediation of arsenic contaminated soil in view of its low cost and environmental benign.

  9. Impact of electrochemical treatment of soil washing solution on PAH degradation efficiency and soil respirometry.

    PubMed

    Mousset, Emmanuel; Huguenot, David; van Hullebusch, Eric D; Oturan, Nihal; Guibaud, Gilles; Esposito, Giovanni; Oturan, Mehmet A

    2016-04-01

    The remediation of a genuinely PAH-contaminated soil was performed, for the first time, through a new and complete investigation, including PAH extraction followed by advanced oxidation treatment of the washing solution and its recirculation, and an analysis of the impact of the PAH extraction on soil respirometry. The study has been performed on the remediation of genuine PAH-contaminated soil, in the following three steps: (i) PAH extraction with soil washing (SW) techniques, (ii) PAH degradation with an electro-Fenton (EF) process, and (iii) recirculation of the partially oxidized effluent for another SW cycle. The following criteria were monitored during the successive washing cycles: PAH extraction efficiency, PAH oxidation rates and yields, extracting agent recovery, soil microbial activity, and pH of soil. Two representative extracting agents were compared: hydroxypropyl-beta-cyclodextrin (HPCD) and a non-ionic surfactant, Tween(®) 80. Six PAH with different numbers of rings were monitored: acenaphthene (ACE), phenanthrene (PHE), fluoranthene (FLA), pyrene (PYR), benzo(a)pyrene (BaP), and benzo(g,h,i)perylene (BghiP). Tween(®) 80 showed much better PAH extraction efficiency (after several SW cycles) than HPCD, regardless of the number of washing cycles. Based on successive SW experiments, a new mathematical relation taking into account the soil/water partition coefficient (Kd*) was established, and could predict the amount of each PAH extracted by the surfactant with a good correlation with experimental results (R(2) > 0.975). More HPCD was recovered (89%) than Tween(®) 80 (79%), while the monitored pollutants were completely degraded (>99%) after 4 h and 8 h, respectively. Even after being washed with partially oxidized solutions, the Tween(®) 80 solutions extracted significantly more PAH than HPCD and promoted better soil microbial activity, with higher oxygen consumption rates. Moreover, neither the oxidation by-products nor the acidic media (p

  10. Impact of electrochemical treatment of soil washing solution on PAH degradation efficiency and soil respirometry.

    PubMed

    Mousset, Emmanuel; Huguenot, David; van Hullebusch, Eric D; Oturan, Nihal; Guibaud, Gilles; Esposito, Giovanni; Oturan, Mehmet A

    2016-04-01

    The remediation of a genuinely PAH-contaminated soil was performed, for the first time, through a new and complete investigation, including PAH extraction followed by advanced oxidation treatment of the washing solution and its recirculation, and an analysis of the impact of the PAH extraction on soil respirometry. The study has been performed on the remediation of genuine PAH-contaminated soil, in the following three steps: (i) PAH extraction with soil washing (SW) techniques, (ii) PAH degradation with an electro-Fenton (EF) process, and (iii) recirculation of the partially oxidized effluent for another SW cycle. The following criteria were monitored during the successive washing cycles: PAH extraction efficiency, PAH oxidation rates and yields, extracting agent recovery, soil microbial activity, and pH of soil. Two representative extracting agents were compared: hydroxypropyl-beta-cyclodextrin (HPCD) and a non-ionic surfactant, Tween(®) 80. Six PAH with different numbers of rings were monitored: acenaphthene (ACE), phenanthrene (PHE), fluoranthene (FLA), pyrene (PYR), benzo(a)pyrene (BaP), and benzo(g,h,i)perylene (BghiP). Tween(®) 80 showed much better PAH extraction efficiency (after several SW cycles) than HPCD, regardless of the number of washing cycles. Based on successive SW experiments, a new mathematical relation taking into account the soil/water partition coefficient (Kd*) was established, and could predict the amount of each PAH extracted by the surfactant with a good correlation with experimental results (R(2) > 0.975). More HPCD was recovered (89%) than Tween(®) 80 (79%), while the monitored pollutants were completely degraded (>99%) after 4 h and 8 h, respectively. Even after being washed with partially oxidized solutions, the Tween(®) 80 solutions extracted significantly more PAH than HPCD and promoted better soil microbial activity, with higher oxygen consumption rates. Moreover, neither the oxidation by-products nor the acidic media (p

  11. HEPA filter monitoring program

    NASA Astrophysics Data System (ADS)

    Kirchner, K. N.; Johnson, C. M.; Aiken, W. F.; Lucerna, J. J.; Barnett, R. L.; Jensen, R. T.

    1986-07-01

    The testing and replacement of HEPA filters, widely used in the nuclear industry to purify process air, are costly and labor-intensive. Current methods of testing filter performance, such as differential pressure measurement and scanning air monitoring, allow determination of overall filter performance but preclude detection of incipient filter failure such as small holes in the filters. Using current technology, a continual in-situ monitoring system was designed which provides three major improvements over current methods of filter testing and replacement. The improvements include: cost savings by reducing the number of intact filters which are currently being replaced unnecessarily; more accurate and quantitative measurement of filter performance; and reduced personnel exposure to a radioactive environment by automatically performing most testing operations.

  12. Electrochemical treatment of spent solution after EDTA-based soil washing.

    PubMed

    Voglar, David; Lestan, Domen

    2012-04-15

    The use of EDTA in soil washing technologies to remediate soils contaminated with toxic metals is prohibitive because of the large volumes of waste washing solution generated, which must be treated before disposal. Degradation of EDTA in the waste solution and the removal of Pb, Zn and Cd were investigated using electrochemical advanced oxidation processes (EAOP) with a boron-doped diamond anode (BDDA), graphite and iron anodes and a stainless-steel cathode. In addition to EAOP, the efficiency of electro-Fenton reactions, induced by the addition of H(2)O(2) and the regulation of electrochemical systems to pH 3, was also investigated. Soil extraction with 15 mmol kg(-1) of soil EDTA yielded waste washing solution with 566 ± 1, 152 ± 1 and 5.5 ± 0.1 mg L(-1) of Pb, Zn and Cd, respectively. Treatments of the waste solution in pH unregulated electrochemical systems with a BDDA and graphite anode (current density 67 mA cm(-2)) were the most efficient and removed up to 98 ± 1, 96 ± 1, 99 ± 1% of Pb, Zn and Cd, respectively, by electrodeposition on the cathode and oxidatively degraded up to 99 ± 1% of chelant. In the electrochemical system with an Fe anode operated at pH 3, the chelant remained preserved in the treated solution, while metals were removed by electrodeposition. This separation opens up the possibility of a new EDTA recycling method from waste soil washing solution. PMID:22305659

  13. Combination of surfactant enhanced soil washing and electro-Fenton process for the treatment of soils contaminated by petroleum hydrocarbons.

    PubMed

    Huguenot, David; Mousset, Emmanuel; van Hullebusch, Eric D; Oturan, Mehmet A

    2015-04-15

    In order to improve the efficiency of soil washing treatment of hydrocarbon contaminated soils, an innovative combination of this soil treatment technique with an electrochemical advanced oxidation process (i.e. electro-Fenton (EF)) has been proposed. An ex situ soil column washing experiment was performed on a genuinely diesel-contaminated soil. The washing solution was enriched with surfactant Tween 80 at different concentrations, higher than the critical micellar concentration (CMC). The impact of soil washing was evaluated on the hydrocarbons concentration in the leachates collected at the bottom of the soil columns. These eluates were then studied for their degradation potential by EF treatment. Results showed that a concentration of 5% of Tween 80 was required to enhance hydrocarbons extraction from the soil. Even with this Tween 80 concentration, the efficiency of the treatment remained very low (only 1% after 24 h of washing). Electrochemical treatments performed thereafter with EF on the collected eluates revealed that the quasi-complete mineralization (>99.5%) of the hydrocarbons was achieved within 32 h according to a linear kinetic trend. Toxicity was higher than in the initial solution and reached 95% of inhibition of Vibrio fischeri bacteria measured by Microtox method, demonstrating the presence of remaining toxic compounds even after the complete degradation. Finally, the biodegradability (BOD₅/COD ratio) reached a maximum of 20% after 20 h of EF treatment, which is not enough to implement a combined treatment with a biological treatment process.

  14. Ceramic HEPA Filter Program

    SciTech Connect

    Mitchell, M A; Bergman, W; Haslam, J; Brown, E P; Sawyer, S; Beaulieu, R; Althouse, P; Meike, A

    2012-04-30

    Potential benefits of ceramic filters in nuclear facilities: (1) Short term benefit for DOE, NRC, and industry - (a) CalPoly HTTU provides unique testing capability to answer questions for DOE - High temperature testing of materials, components, filter, (b) Several DNFSB correspondences and presentations by DNFSB members have highlighted the need for HEPA filter R and D - DNFSB Recommendation 2009-2 highlighted a nuclear facility response to an evaluation basis earthquake followed by a fire (aka shake-n-bake) and CalPoly has capability for a shake-n-bake test; (2) Intermediate term benefit for DOE and industry - (a) Filtration for specialty applications, e.g., explosive applications at Nevada, (b) Spin-off technologies applicable to other commercial industries; and (3) Long term benefit for DOE, NRC, and industry - (a) Across industry, strong desire for better performance filter, (b) Engineering solution to safety problem will improve facility safety and decrease dependence on associated support systems, (c) Large potential life-cycle cost savings, and (d) Facilitates development and deployment of LLNL process innovations to allow continuous ventilation system operation during a fire.

  15. Treatment of Wastewater From Car Washes Using Natural Coagulation and Filtration System

    NASA Astrophysics Data System (ADS)

    Al-Gheethi, A. A.; Mohamed, R. M. S. R.; Rahman, M. A. A.; Johari, M. R.; Kassim, A. H. M.

    2016-07-01

    Wastewater generated from carwash is one of the main wastewater resources, which contribute effectively in the increasing of environmental contamination due to the chemical characteristics of the car wastes. The present work aimed to develop an integrated treatment system for carwash wastewater based on coagulation and flocculation using Moringa oleifera and Ferrous Sulphate (FeSO4.7H2O) as well as natural filtration system. The carwash wastewater samples were collected from carwash station located at Parit Raja, Johor, Malaysia. The treatment system of car wash wastewater was designed in the lab scale in four stages included, aeration, coagulation and flocculation, sedimentation and filtration. The coagulation and flocculation unit was carried out using different dosage (35, 70, 105 and 140 mg L-1) of M. oleifera and FeSO4.7H2O, respectively. The efficiency of the integrated treatment system to treat carwash wastewater and to meet Environmental Quality Act (EQA 1974) was evaluated based on the analysis of pH, dissolved oxygen (DO), chemical oxygen demand (COD) and turbidity (NTU). The integrated treatment system was efficient for treatment of raw carwash wastewater. The treated carwash wastewaters meet EQA 1974 regulation 2009 (Standards A) in the term of pH and DO while, turbidity and COD reduced in the wastewater to meet Standards B. The integrated treatment system designed here with natural coagulant (M. oleifera) and filtration unit were effective for primary treatment of carwash wastewater before the final disposal or to be reused again for carwash process.

  16. Treatment of tunnel wash waters--experiments with organic sorbent materials. Part II: Removal of toxic metals.

    PubMed

    Paruch, Adam M; Roseth, Roger

    2008-01-01

    In the first part of the article, the column and the bag experiments concerning removal of polycyclic aromatic hydrocarbons (PAHs) and nonpolar oil (NPO) from tunnel wash waters using organic sorbent materials have been described. This part presents the results of removal of toxic metals. The metals of concern (Al, As, Cd, Cr, Cu, Fe, Pb, Mo, Ni, and Zn) were selected based on the priority toxicant pollutants defined in surface water quality criteria. Concentrations of these metals in the collected effluents varied more than the concentrations of PAHs and NPO, and thus only metal contents were considered for statistical analyses. These analyses determined significant differences (P < 0.05, P < 0.01, and P < 0.001) between the mean metal concentrations in the column effluents and those in applied wash water of road tunnel. The results obtained during both experiments revealed that the organic sorbents, and in particular their combination, removed toxic metals more effectively from wash water of road tunnel than from wash water of tunnel electrostatic filters. Among the investigated toxicants, Al and Fe showed the highest levels of reduction in the column experiment, 99.7% and 99.6%, respectively. The lowest reduction levels of 66.0% and 76.2% were found for Pb and Mo, respectively. The results of the bag experiment showed that even one day treatment of wash waters from tunnel electrostatic filters could reduce concentration of some toxicants by more than 70% (Al and Fe) and 80% (Cu).

  17. Remediation of oil-based drill cuttings through a biosurfactant-based washing followed by a biodegradation treatment.

    PubMed

    Yan, Ping; Lu, Mang; Guan, Yueming; Zhang, Weimu; Zhang, Zhongzhi

    2011-11-01

    In this study, oil-based drill cuttings were washed by a rhamnolipid solution and then subjected to bioremediation in stainless steel boxes using sawdust as bulking agent. A mixed bacterial culture, mainly containing Pseudomonas, Acinetobacter, Alcaligenes, Agrobacterium, and Comamonas, was used as inoculums. Approximately 83% of organics were removed after washing under optimal conditions (liquid/solid ratio, 3:1; washing time, 20 min; stirring speed, 200 rpm; rhamnolipid concentration, 360 mg/L; temperature, 60 °C), and the total petroleum hydrocarbon concentration of the cuttings dropped from 85,000 to 12,600 mg/kg. In the bioremediation stage, concentrations of saturated and aromatic hydrocarbons decreased to 2140 and 1290 mg/kg, respectively, after 120 days. Ultrahigh-resolution mass spectrometry demonstrated that oxygen- and nitrogen-containing compounds had undergone biodegradation. The results of this study indicate that this two-stage remedial system can reduce treatment time and increase treatment efficiency as compared with a single bioremediation or washing treatment.

  18. EDTA leaching of Cu contaminated soil using electrochemical treatment of the washing solution.

    PubMed

    Pociecha, Maja; Lestan, Domen

    2009-06-15

    The feasibility of a two-phase method for remediation of Cu (364+/-2 mg kg(-1)) contaminated vineyard soil was evaluated. In the first phase we used ethylenediamine tetraacetae (EDTA) for Cu leaching, while in the second phase we used an electrochemical advanced oxidation process (EAOP) for the treatment and reuse of the washing solution for soil rinsing (removal of soil-retained, chelant-mobilized Cu complexes) in a closed loop. In the EAOP, a boron-doped diamond anode was used for the generation of hydroxyl radicals and oxidative decomposition of EDTA-metal complexes at a constant current density (40 mA cm(-2)). The released Cu was removed from the solution mostly as an electro-deposit on the cathode. Two consecutive additions of 10 mmol kg(-1) EDTA removed 26% of Cu from the soil, mostly from carbonate and oxide soil fractions (58% and 40% Cu reduction). The soil Cu oral availability (in vitro Physiologically Based Extraction Test) was reduced after remediation by 42% and 51% in the simulated stomach and intestinal phases. The discharge solution was clear, almost colorless, with pH 8.4 and 0.5 mg L(-1) Cu and 0.07 mM EDTA. The novel method enables soil Cu availability stripping using small volumes of process waters, and no wastewater generation or other emissions into the environment. PMID:19022571

  19. In Situ Cleanable HEPA Filter

    SciTech Connect

    Phillips, T.D.

    1999-11-18

    This paper describes a welded steel HEPA filter which uses liquid spray cleaning and vacuum drying. Development of the filter was initiated in order to eliminate personnel exposure, disposal cost, and short lifetime associated with systems commonly employed throughout the Department of Energy complex. In addition the design promises to resolve the issues of fire, elevated temperatures, wetting, filter strength, air leaks and aging documented in the May, 1999 DNFSB-TECH-23 report.

  20. HEPA Filter Use at the Hanford Site

    SciTech Connect

    KRISKOVICH, J.R.

    2002-02-20

    High Efficiency Particulate Air (HEPA) filters are relied upon at the Hanford site to support several different activities. Each facility relies upon the filters to provide the same function, remove radioactive particulate However, HEPA filters are operated in differing environmental conditions from one facility to another and the constituents in the air streams also differ. In addition, some HEPA filters at the Hanford site have been in service for several years. As a result, an assessment was performed which evaluated the service life and conditions of the HEPA filters at the Hanford site.

  1. HEPA Filter Use at the Hanford Site

    SciTech Connect

    Kriskovich, J. R.

    2002-02-28

    High Efficiency Particulate Air (HEPA) filters are relied upon at the Hanford site to support several different activities. Each facility relies upon the filters to provide the same function; remove radioactive particulate from various air streams. However, HEPA filters are operated in differing environmental conditions from one facility to another and the constituents in the air streams also differ. In addition, some HEPA filters at the Hanford site have been in service for several years. As a result, an assessment was performed which evaluated the service life and conditions of the HEPA filters at the Hanford site.

  2. The application of the ozonation/electrocoagulation treatment process of the boat pressure washing wastewater.

    PubMed

    Orescanin, Visnja; Kollar, Robert; Nad, Karlo

    2011-01-01

    This paper provides the information on the optimum conditions of the treatment process of the boat pressure washing wastewater (BPWW) by the combination of the ozonation and electrochemical (EC) methods developed on the laboratory and pilot plant scale. The initial effluent was highly enriched in heavy metals and elevated levels of organic contaminants. The concentrations of V, Cr, Fe, Cu, Zn, TOC, and COD exceeded the upper permissible limits of 22, 20, 6, 112, 17, 4, and 2 times, respectively. The main mechanisms of the organic matter destruction were the ozone oxidation and the indirect oxidation with chlorine/hypochlorite formed by the anodic oxidation of chloride already present in the wastewater. The heavy metal removal was forced by the coagulation/flocculation using Fe(2+), Fe(3+), and Al(3+) ions released into the treated solution by electrochemical corrosion of the sacrificial stainless steel and aluminum electrodes. At the optimum conditions obtained with the pilot plant, the removal efficiencies of the parameters V, Cr, Fe, Ni, Cu, Zn, Pb, TOC, and COD were 100.00 %, 99.35 %, 99.51 %, 87.31 %, 99.83 %, 99.65 %, 100.00 %, 88.46 %, and 76.28 %, respectively. All the parameters in the final effluent were in agreement with regulated values. The advantages of this system compared to its physico-chemical counterparts are as follows: (1) no need for the external addition of flocculating agents since they are electrochemically generated inside the treatment tank; (2) minimal pH changes during the treatment process not requiring pH adjustment by acids/basis; (3) a significantly lower amount of sludge since only Fe and Al ions were released in the solution; (4) flocs formed by the electrocoagulation can be easily separated by the filtration due to their higher stability, lower content of the bound water and larger surface compared to chemical flocs; (5) the final EC effluent is clear, colourless and odourless, containing the less total dissolved solids and

  3. TECHNOLOGY EVALUATION REPORT: BIOTROL SOIL WASHING SYSTEM FOR TREATMENT OF A WOOD PRESERVING SITE - VOLUME II

    EPA Science Inventory

    The SITE Program demonstration of one configuration of the BioTrol Soil Washing System (BSWS) was conducted to obtain reliable performance and cost data that can be used to evaluate the potential applicability of the technology as a remediation alternative for sites contaminated ...

  4. BESCORP SOIL WASHING SYSTEM FOR LEAD BATTERY SITE TREATMENT - APPLICATIONS ANALYSIS REPORT

    EPA Science Inventory

    This report evaluates the Brice Environmental Services Corporation (BESCORP) Soil Washing System (BSWS) and Its applicability in remediating lead-contaminated soil at lead battery sites. It presents performance and economic data, developed from the U.S. Environmental Protection A...

  5. SOLVENT EXTRACTION AND SOIL WASHING TREATMENT OF CONTAMINATED SOILS FROM WOOD PRESERVING SITES: BENCH SCALE STUDIES

    EPA Science Inventory

    Bench-scale solvent extraction and soil washing studies were performed on soil samples obtained from three abandoned wood preserving sites that included in the NPL. The soil samples from these sites were contaminated with high levels of polyaromatic hydrocarbons (PAHs), pentachlo...

  6. Water washable stainless steel HEPA filter

    DOEpatents

    Phillips, Terrance D.

    2001-01-01

    The invention is a high efficiency particulate (HEPA) filter apparatus and system, and method for assaying particulates. The HEPA filter provides for capture of 99.99% or greater of particulates from a gas stream, with collection of particulates on the surface of the filter media. The invention provides a filter system that can be cleaned and regenerated in situ.

  7. Hand Washing

    MedlinePlus

    ... dirty little secrets: Students don't wash their hands often or well. In one study, only 58% of female and 48% of male middle- and high-school students washed their hands after using the bathroom. Yuck! previous continue How ...

  8. Influence of bentonite in polymer membranes for effective treatment of car wash effluent to protect the ecosystem.

    PubMed

    Kiran, S Aditya; Arthanareeswaran, G; Thuyavan, Y Lukka; Ismail, A F

    2015-11-01

    In this study, modified polyethersulfone (PES) and cellulose acetate (CA) membranes were used in the treatment of car wash effluent using ultrafiltration. Hydrophilic sulfonated poly ether ether ketone (SPEEK) and bentonite as nanoclay were used as additives for the PES and CA membrane modification. Performances of modified membranes were compared with commercial PES membrane with 10kDa molecular weight cut off (MWCO). The influencing parameters like stirrer speed (250-750rpm) and transmembrane pressure (100-600kPa) (TMP) were varied and their effects were studied as a function of flux. In the treatment of car wash effluent, a higher permeate flux of 52.3L/m(2)h was obtained for modified CA membrane at TMP of 400kPa and stirrer speed of 750rpm. In comparison with modified PES membrane and commercial PES membrane, modified CA membranes showed better performance in terms of flux and flux recovery ratio. The highest COD removal (60%) was obtained for modified CA membrane and a lowest COD removal (47%) was observed for commercial PES membrane. The modified membranes were better at removing COD, turbidity and maintained more stable flux than commercial PES membrane, suggesting they will provide better economic performance in car wash effluent reclamation.

  9. Influence of bentonite in polymer membranes for effective treatment of car wash effluent to protect the ecosystem.

    PubMed

    Kiran, S Aditya; Arthanareeswaran, G; Thuyavan, Y Lukka; Ismail, A F

    2015-11-01

    In this study, modified polyethersulfone (PES) and cellulose acetate (CA) membranes were used in the treatment of car wash effluent using ultrafiltration. Hydrophilic sulfonated poly ether ether ketone (SPEEK) and bentonite as nanoclay were used as additives for the PES and CA membrane modification. Performances of modified membranes were compared with commercial PES membrane with 10kDa molecular weight cut off (MWCO). The influencing parameters like stirrer speed (250-750rpm) and transmembrane pressure (100-600kPa) (TMP) were varied and their effects were studied as a function of flux. In the treatment of car wash effluent, a higher permeate flux of 52.3L/m(2)h was obtained for modified CA membrane at TMP of 400kPa and stirrer speed of 750rpm. In comparison with modified PES membrane and commercial PES membrane, modified CA membranes showed better performance in terms of flux and flux recovery ratio. The highest COD removal (60%) was obtained for modified CA membrane and a lowest COD removal (47%) was observed for commercial PES membrane. The modified membranes were better at removing COD, turbidity and maintained more stable flux than commercial PES membrane, suggesting they will provide better economic performance in car wash effluent reclamation. PMID:25869419

  10. Conformational changes in proteins recovered from jumbo squid (Dosidicus gigas) muscle through pH shift washing treatments.

    PubMed

    Cortés-Ruiz, Juan A; Pacheco-Aguilar, Ramón; Ramírez-Suárez, Juan C; Lugo-Sánchez, Maria E; García-Orozco, Karina D; Sotelo-Mundo, Rogerio R; Peña-Ramos, Aida

    2016-04-01

    Conformational and thermal-rheological properties of acidic (APC) and neutral (NPC) protein concentrates were evaluated and compared to those of squid (Dosidicus gigas) muscle proteins (SM). Surface hydrophobicity, sulfhydryl status, secondary structure profile, differential scanning calorimetry and oscillatory dynamic rheology were used to evaluate the effect of treatments on protein properties. Acidic condition during the washing process (APC) promoted structural and conformational changes in the protein present in the concentrate produced. These changes were enhanced during the heat setting of the corresponding sol. Results demonstrate that washing squid muscle under the proposed acidic conditions is a feasible technological alternative for squid-based surimi production improving its yield and gel-forming ability.

  11. Application of an electrochemical treatment for EDDS soil washing solution regeneration and reuse in a multi-step soil washing process: Case of a Cu contaminated soil.

    PubMed

    Ferraro, Alberto; van Hullebusch, Eric D; Huguenot, David; Fabbricino, Massimiliano; Esposito, Giovanni

    2015-11-01

    Soil washing is an extensively used process for remediation of heavy metals contaminated soils. However the amount of fresh washing solution to be used represents a significant economical drawback of this process. This paper investigates the application of an electrochemical process (Fe/Fe electrodes couple) for the regeneration of a spent EDDS solution, containing Cu and major competitor cations (Ca, Fe, Mg, and Mn). The effect of current density, pH and conductivity of the washing solution on the recovery process performances was investigated. Current density showed the highest influence on Cu, Mg and Mn removal yields. Maximum removal yields reached 99% for Cu, 77% for Mn and 49% for Mg. No influence of the investigated parameters on Ca removal was observed, while an increase of Fe concentration due to anode dissolution occurred. Characterization of sludge produced from the 2 h electrochemical test (5 mA cm(-2), pH = 8, 8 mS cm(-1)) displayed concentrations of 2.8 g kg(-1) for Ca, 0.4 g kg(-1) for Cu, 535.6 g kg(-1) for Fe, 2.6 g kg(-1) for Mg. TCLP tests at pH 2.88 and 4.93 showed a low leaching percentage (Ca, 10-21%; Cu, 6-12%; Fe, 0.22% Mg, 27-36%). Multi-washing tests were carried out to assess the decrease of the chelating ability of the regenerated washing solution and the Cu extraction efficiency.

  12. Comparison between treatment of kitchen-sink wastewater and a mixture of kitchen-sink and washing-machine wastewaters.

    PubMed

    Huelgas, A; Nakajima, M; Nagata, H; Funamizu, N

    2009-01-01

    In this paper, a submerged membrane bioreactor was used to treat 'higher-load' grey water: (a) kitchen-sink wastewater only, and (b) a mixture of kitchen-sink wastewater and washing-machine wastewater. For each type of wastewater, three systems operated at different hydraulic retention times (HRTs) were investigated. In the mixture of kitchen-sink wastewater and washing-machine wastewater, the reactor with a short HRT of four hours was stopped due to foaming. It has been observed that for both types of wastewater, an HRT of eight hours or longer can be used for the treatment. However, it has been observed that a higher COD in the permeate of the mixture can be obtained compared with that of the kitchen-sink wastewater only. This indicated that washing-machine wastewater has some component that is not easily biodegradable. The total linear akylbenzene sulfonate (LAS) removal was > 99% even at a concentration of 10-23 mg 1(-1).

  13. Treatment of real wastewater produced from Mobil car wash station using electrocoagulation technique.

    PubMed

    El-Ashtoukhy, E-S Z; Amin, N K; Fouad, Y O

    2015-10-01

    This paper deals with the electrocoagulation of real wastewater produced from a car wash station using a new cell design featuring a horizontal spiral anode placed above a horizontal disc cathode. The study dealt with the chemical oxygen demand (COD) reduction and turbidity removal using electrodes in a batch mode. Various operating parameters such as current density, initial pH, NaCl concentration, temperature, and electrode material were examined to optimize the performance of the process. Also, characterization of sludge formed during electrocoagulation was carried out. The results indicated that the COD reduction and turbidity removal increase with increasing the current density and NaCl concentration; pH from 7 to 8 was found to be optimum for treating the wastewater. Temperature was found to have an insignificant effect on the process. Aluminum was superior to iron as a sacrificial electrode material in treating car wash wastewater. Energy consumption based on COD reduction ranged from 2.32 to 15.1 kWh/kg COD removed depending on the operating conditions. Finally, the sludge produced during electrocoagulation using aluminum electrodes was characterized by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS) analysis.

  14. Biting and bloodsucking lice of dogs--treatment by means of a neem seed extract (MiteStop®, Wash Away Dog).

    PubMed

    Mehlhorn, Heinz; Walldorf, Volker; Abdel-Ghaffar, Fathy; Al-Quraishy, Saleh; Al-Rasheid, Khaled A S; Mehlhorn, Julia

    2012-02-01

    Dogs infested with lice belonging either to the group of Mallophaga (hairlings, i.e., Trichodectes canis) or Anoplura (bloodsucking lice, e.g., Linognathus setosus) were washed with the neem seed preparations MiteStop® or Wash Away Dog. It was found that a single treatment with one of these products killed both motile stages and those developing inside eggs (nits) being glued at the hair. In both cases the product had been left for 20 min onto the hair before it was washed away just with normal tap water. PMID:21881947

  15. Effects of acid-washing filter treatment on quantification of aerosol organic compounds

    NASA Astrophysics Data System (ADS)

    Yang, Liming; Lim, Jaehyun; Yu, Liya E.

    The tests of standard mixtures and four sets of atmospheric particulate samples showed that an acid-wash (AW) pretreatment of fluorocarbon-coated glass fiber filters prior to aerosol sampling enhanced the quantifiable organic compounds for more than 29% (or 66 ng m -3); in particular, 47-273 ng m -3 (21-366%) more water-soluble organic compounds (WSOCs) were measured. When the acid-pretreated filters were employed, up to nine more organic species were measured in the individual daily samples. Because the acid pretreatment reduced the metal contaminants in the glass fiber filters, using the AW filters for aerosol sampling allows higher extraction recoveries of organic compounds. Since the fingerprinting compounds were more accurately determined when the aerosol samples were collected on the AW filters, better assessment of emission sources and toxicity of air pollutants can be obtained.

  16. SEPARATION OF HAZARDOUS ORGANICS BY LOW PRESSURE MEMBRANES: TREATMENT OF SOIL-WASH RINSE-WATER LEACHATES

    EPA Science Inventory

    Soil washing is a promising technology for treating contaminated soils. In the present work, low-pressure, thin-film composite membranes were evaluated to treat the soil-wash leachates so that the treated water could be recycled back to the soil washing step. Experiments were don...

  17. Hand washing.

    PubMed

    2016-07-01

    A surgery matron has writt en a hand hygiene promotional video rap to encourage staff, patients and visitors to wash their hands. Vicky Cartwright from University Hospitals of Leicester NHS Trust rewrote the lyrics to 1990s hit rap, Ice Ice Baby.

  18. Hand washing.

    PubMed

    2016-07-01

    A surgery matron has writt en a hand hygiene promotional video rap to encourage staff, patients and visitors to wash their hands. Vicky Cartwright from University Hospitals of Leicester NHS Trust rewrote the lyrics to 1990s hit rap, Ice Ice Baby. PMID:27380706

  19. Evaluation of performance and community dynamics of microorganisms during treatment of distillery spent wash in a three stage bioreactor.

    PubMed

    Kaushik, Garima; Gopal, Madhuban; Thakur, Indu Shekhar

    2010-06-01

    The ability of Emericella nidulans var. lata, Neurospora intermedia and Bacillus sp. to treat distillery spent wash in a three stage bioreactor was investigated. Process parameters were optimized in shake flask cultures with the individual strains before treatment of the effluent in a 15-l bioreactor. Treatment was first carried out by the fungi followed by bacteria. The treated effluent showed significant reduction in color (82%) and COD (93%) after 30 h. Metabolites formed after degradation of complex polymers in distillery effluent were assayed by gas chromatography-mass spectroscopy and included furan, simple acid types and organic compounds. Denaturing gradient gel electrophoresis of 16S rDNA and 18S rDNA sequences amplified from DNA isolated from the reactor communities indicated the presence of other organisms besides those introduced initially. The microbial communities were able to carry out bioremediation of distillery effluent and produce discharge that conforms to safety standards. PMID:20156685

  20. Evaluation of performance and community dynamics of microorganisms during treatment of distillery spent wash in a three stage bioreactor.

    PubMed

    Kaushik, Garima; Gopal, Madhuban; Thakur, Indu Shekhar

    2010-06-01

    The ability of Emericella nidulans var. lata, Neurospora intermedia and Bacillus sp. to treat distillery spent wash in a three stage bioreactor was investigated. Process parameters were optimized in shake flask cultures with the individual strains before treatment of the effluent in a 15-l bioreactor. Treatment was first carried out by the fungi followed by bacteria. The treated effluent showed significant reduction in color (82%) and COD (93%) after 30 h. Metabolites formed after degradation of complex polymers in distillery effluent were assayed by gas chromatography-mass spectroscopy and included furan, simple acid types and organic compounds. Denaturing gradient gel electrophoresis of 16S rDNA and 18S rDNA sequences amplified from DNA isolated from the reactor communities indicated the presence of other organisms besides those introduced initially. The microbial communities were able to carry out bioremediation of distillery effluent and produce discharge that conforms to safety standards.

  1. Effect of washing, antibiotics and trypsin treatment of bovine embryos on the removal of adhering K99+ Escherichia coli.

    PubMed

    Otoi, T; Tachikawa, S; Kondo, S; Suzuki, T

    1993-12-01

    Bovine embryos with the intact zona pellucida were exposed in vitro to K99+ Escherichia coli (K99 E. coli). The recommended procedures for washing and treating embryos were then evaluated for their effectiveness in removing or killing the adherent bacteria. After 10-step washing, bacteria were recovered not only from the embryos exposed to E. coli suspensions but also from those treated with trypsin during washing. On the other hand, no bacteria were recovered from any embryos treated with antibiotics (gentamicin; 50 micrograms/ml) in culture medium before washing, indicating that the recommended washing procedures with appropriate antibiotics assure that zona pellucida-intact bovine embryos are free from E. coli.

  2. Successful treatment of severe oligozoospermia with sperm washing and intrauterine insemination.

    PubMed

    Centola, G M

    1997-01-01

    During the period January 1, 1991 through December 31, 1995, 258 patients, in whom motile sperm counts for insemination (postwash, processed) were 10.0 million motile sperm or less were seen in the andrology unit for sperm washing and intrauterine insemination (IUI). No significant female factors were noted on history; all female partners had patent Fallopian tubes and were ovulatory spontaneously or were treated by the referring gynecologist with clomiphene citrate, human menopausal gonadotropin (hMG), or follicle-stimulating hormone (FSH) ovulation induction in both anovulatory or ovulatory women. Of the total of 258 patients, 15 achieved a pregnancy in 284 cycles of IUI in which the inseminating motile-count was < 1.0 million motile sperm, resulting in a monthly fecundity (f) of 5.3%. The mean (+/-SD) motile count for IUI in this group was 0.61 (+/-0.29) million sperm, with a range of 0.19-0.95 million motile sperm. The initial motile count was 2.97 (3.2) million sperm, with a range of 0.2-12.81 million sperm. With inseminating motile counts of 1.0-10.0 million motile sperm, there were 83 pregnancies after 467 cycles of IUI, resulting in a monthly f of 17.8%. The mean (+/-SD) motile count for IUI in this group was 4.9 (+/-2.7) million motile sperm with a range of 1.0-9.9 million motile sperm. The initial sperm count in this group was 10.9 million (+/-7.1), with a range of 1.1-23.7 million motile sperm. These data suggest that acceptable pregnancy rates can be achieved with IUI, even in severely oligozoospermic specimens. Intrauterine insemination is less invasive and less costly than other assisted reproductive techniques. These data are supportive of IUI prior to attempting other more invasive and potentially costly reproductive technologies. PMID:9283959

  3. Treatment of tunnel wash waters--experiments with organic sorbent materials. Part I: Removal of polycyclic aromatic hydrocarbons and nonpolar oil.

    PubMed

    Paruch, Adam M; Roseth, Roger

    2008-01-01

    Tunnel wash waters characterize all waters that run off after washing procedures of tunnels are performed. These waters represent a wide spectrum of organic and inorganic pollutants, such as polycyclic aromatic hydrocarbons (PAHs) and toxic metals. Removal of such contaminants from water runoff was investigated using laboratory tests after washing procedure was performed on two road tunnels in eastern Norway (Hanekleiv and Bragernes). Due to diverse character of both, treatment media and treated wash waters, the whole investigation was divided into two separate laboratory experiments. The treatment efficiencies were established based on the levels of concentrations and reductions of the measured contaminants in the effluents released from the tested media. In the first part of the article, the contents of nonpolar oil (NPO), 16 individual PAHs, and total PAHs are described. This part revealed that the combination of two organic sorbent materials provided the highest treatment efficiency for wash waters released from the road tunnel and from electrostatic filters. The greatest reduction levels reached 97.6% for NPO, 97.2% for benzo[a]pyrene, and 96.5% for the total PAHs. In the second part of the article, the concentrations and the removal rates of toxic metals are reported.

  4. Evaluation of HEPA filter service life

    SciTech Connect

    Fretthold, J.K.; Stithem, A.R.

    1997-07-14

    Rocky Flats Environmental Technology Site (RFETS), has approximately 10,000 High Efficiency Particulate Air (HEPA) Filters installed in a variety of filter plenums. These ventilation/filtration plenum systems are used to control the release of airborne particulate contaminates to the environment during normal operations and potential accidents. This report summarizes the results of destructive and non-destructive tests on HEPA filters obtained from a wide variety of ages and service conditions. These tests were performed to determine an acceptable service life criteria for HEPA filters used at Rocky Flats Environmental Technology Site (RFETS). A total of 140 filters of various ages (1972 to 1996) and service history (new, aged unused, used) were tested. For the purpose of this report, filter age from manufacture date/initial test date to the current sample date was used, as opposed to the actual time a filter was installed in an operating system.

  5. Insitu Cleanable Alternative HEPA Filter Media

    SciTech Connect

    Adamson, D.J.

    2002-05-14

    Two types of filter media, sintered nickel metal and ceramic monolith membrane, are being investigated as in situ regenerable/cleanable high efficiency particulate air (HEPA) filters. Particle retention testing was conducted on the filters at the Oak Ridge Filter Test Facility to ensure HEPA efficiency, greater than 99.97 percent. During simulant testing, The filters were challenged using non-radioactive simulated high-level waste materials and atmospheric dust; materials that cause filter pluggage in the field. After plugging the filters they were cleaned in situ using an aqueous solution. This innovative approach of the in situ regenerative filtration system may be a significant improvement upon the shortfalls of conventional disposable HEPA filters.

  6. Volatility and leachability of heavy metals and radionuclides in thermally treated HEPA filter media generated from nuclear facilities.

    PubMed

    Yoon, In-Ho; Choi, Wang-Kyu; Lee, Suk-Chol; Min, Byung-Youn; Yang, Hee-Chul; Lee, Kune-Woo

    2012-06-15

    The purpose of the present study was to apply thermal treatments to reduce the volume of HEPA filter media and to investigate the volatility and leachability of heavy metals and radionuclides during thermal treatment. HEPA filter media were transformed to glassy bulk material by thermal treatment at 900°C for 2h. The most abundant heavy metal in the HEPA filter media was Zn, followed by Sr, Pb and Cr, and the main radionuclide was Cs-137. The volatility tests showed that the heavy metals and radionuclides in radioactive HEPA filter media were not volatilized during the thermal treatment. PCT tests indicated that the leachability of heavy metals and radionuclides was relatively low compared to those of other glasses. XRD results showed that Zn and Cs reacted with HEPA filter media and were transformed into crystalline willemite (ZnO·SiO(2)) and pollucite (Cs(2)OAl(2)O(3)4SiO(2)), which are not volatile or leachable. The proposed technique for the volume reduction and transformation of radioactive HEPA filter media into glassy bulk material is a simple and energy efficient procedure without additives that can be performed at relatively low temperature compared with conventional vitrification process. PMID:22525481

  7. In Situ Cleanable Alternative HEPA Filter Media

    SciTech Connect

    Adamson, D. J.; Terry, M. T.

    2002-02-28

    The Westinghouse Savannah River Company, located at the Savannah River Site in Aiken, South Carolina, is currently testing two types of filter media for possible deployment as in situ regenerable/cleanable High Efficiency Particulate Air (HEPA) filters. The filters are being investigated to replace conventional, disposable, glass-fiber, HEPA filters that require frequent removal, replacement, and disposal. This is not only costly and subjects site personnel to radiation exposure, but adds to the ever-growing waste disposal problem. The types of filter media being tested, as part of a National Energy Technology Laboratory procurement, are sintered nickel metal and ceramic monolith membrane. These media were subjected to a hostile environment to simulate conditions that challenge the high-level waste tank ventilation systems. The environment promoted rapid filter plugging to maximize the number of filter loading/cleaning cycles that would occur in a specified period of time. The filters were challenged using nonradioactive simulated high-level waste materials and atmospheric dust; materials that cause filter pluggage in the field. The filters are cleaned in situ using an aqueous solution. The study found that both filter media were insensitive to high humidity or moisture conditions and were easily cleaned in situ. The filters regenerated to approximately clean filter status even after numerous plugging and in situ cleaning cycles. Air Techniques International is conducting particle retention testing on the filter media at the Oak Ridge Filter Test Facility. The filters are challenged using 0.3-mm di-octyl phthalate particles. Both the ceramic and sintered media have a particle retention efficiency > 99.97%. The sintered metal and ceramic filters not only can be cleaned in situ, but also hold great potential as a long life alternative to conventional HEPA filters. The Defense Nuclear Facility Safety Board Technical Report, ''HEPA Filters Used in the Department of

  8. Efficacy of plant-derived antimicrobials as antimicrobial wash treatments for reducing enterohemorrhagic Escherichia coli O157:H7 on apples.

    PubMed

    Baskaran, Sangeetha Ananda; Upadhyay, Abhinav; Kollanoor-Johny, Anup; Upadhyaya, Indu; Mooyottu, Shankumar; Roshni Amalaradjou, Mary Anne; Schreiber, David; Venkitanarayanan, Kumar

    2013-09-01

    This study investigated the efficacy of 3 GRAS-status, plant-derived antimicrobials (PDAs), trans-cinnamaldehyde (TC), carvacrol (CR), and β-resorcylic acid (BR) applied as an antimicrobial wash for killing Escherichia coli O157:H7 on apples. "Red delicious" apples inoculated with a 5 strain mixture of E. coli O157:H7 were subjected to washing in sterile deionized water containing 0% PDA (control), 0.15% TC, 0.35% TC, 0.15% CR, 0.30% CR, 0.5% BR, or 1% BR for 1, 3, and 5 min at 23 °C in the presence and absence of 1% soil, and surviving pathogen populations on apples were enumerated at each specified time. All PDAs were more effective in reducing E. coli O157:H7 compared to the water wash treatment (P < 0.05) and reduced the pathogen by 4- to 5-log CFU/apple in 5 min. Chlorine (1%) was the most effective treatment reducing the pathogen on apples to undetectable levels in 1 min (P < 0.05). Moreover, the antimicrobial effect of CR and BR was not affected by the presence of soil, whereas the efficacy of TC and BR was decreased in the presence of soil. Further, no bacteria were detected in the wash solution containing CR and BR; however, E. coli O157:H7 was recovered in the control wash water and treatment solutions containing TC and chlorine, in the presence of 1% soil (P < 0.05). Results suggest that the aforementioned PDAs, especially CR and BR could be used effectively to kill E. coli O157:H7 on apples when used as a wash treatment. Studies on the sensory and quality characteristics of apples treated with PDAs are needed before recommending their usage.

  9. In-place HEPA filter penetration test

    SciTech Connect

    Bergman, W.; Wilson, kK.; Elliott, J.; Bettencourt, B.; Slawski, J.W.

    1997-01-01

    We have demonstrated the feasibility of conducting penetration tests on high efficiency particulate air (HEPA) filters as installed in nuclear ventilation systems. The in-place penetration test, which is designed to yield equivalent penetration measurements as the standard DOP efficiency test, is based on measuring the aerosol penetration of the filter installation as a function of particle size using a portable laser particle counter. This in-place penetration test is compared to the current in-place leak test using light scattering photometers for single HEPA filter installations and for HEPA filter plenums using the shroud method. Test results show the in-place penetration test is more sensitive than the in-place leak test, has a similar operating procedure, but takes longer to conduct. Additional tests are required to confirm that the in-place penetration test yields identical results as the standard dioctyl phthalate (DOP) penetration test for HEPA filters with controlled leaks in the filter and gasket and duct by-pass leaks. Further development of the procedure is also required to reduce the test time before the in- place penetration test is practical.

  10. In-place HEPA filter penetration test

    SciTech Connect

    Bergman, W.; Wilson, K.; Elliott, J.

    1997-08-01

    We have demonstrated the feasibility of conducting penetration tests on high efficiency particulate air (HEPA) filters as installed in nuclear ventilation systems. The in-place penetration test, which is designed to yield equivalent penetration measurements as the standard DOP efficiency test, is based on measuring the aerosol penetration of the filter installation as a function of particle size using a portable laser particle counter. This in-place penetration test is compared to the current in-place leak test using light scattering photometers for single HEPA filter installations and for HEPA filter plenums using the shroud method. Test results show the in-place penetration test is more sensitive than the in-place leak test, has a similar operating procedure, but takes longer to conduct. Additional tests are required to confirm that the in-place penetration test yields identical results as the standard dioctyl phthalate (DOP) penetration test for HEPA filters with controlled leaks in the filter and gasket and duct by-pass leaks. Further development of the procedure is also required to reduce the test time before the in-place penetration test is practical. 14 refs., 14 figs., 3 tabs.

  11. HEPA filter fire (and subsequent unfiltered release)

    SciTech Connect

    Powers, T.B.

    1996-09-27

    This document supports the development and presentation of the following accident scenario in the TWRS Final Safety Analysis Report: HEPA Filter Failure - Exposure to High Temperature or Pressure. The calculations needed to quantify the risk associated with this accident scenario are included within.

  12. HEPA filter fire (and subsequent unfiltered release)

    SciTech Connect

    Ryan, G.W., Westinghouse Hanford

    1996-08-12

    This document supports the development and presentation of the following accident scenario in the TWRS Final Safety Analysis Report: HEPA Filter Failure - Exposure to High Temperature or Pressure. The calculations needed to quantify the risk associated with this accident scenario are included within.

  13. Define and Quantify the Physics of Air Flow, Pressure Drop and Aerosol Collection in Nuclear Grade HEPA Filters

    SciTech Connect

    Moore, Murray E.

    2015-02-23

    Objective: Develop a set of peer-review and verified analytical methods to adjust HEPA filter performance to different flow rates, temperatures and altitudes. Experimental testing will measure HEPA filter flow rate, pressure drop and efficiency to verify the analytical approach. Nuclear facilities utilize HEPA (High Efficiency Particulate Air) filters to purify air flow for workspace ventilation. However, the ASME AG-1 technical standard (Code on Nuclear Air and Gas Treatment) does not adequately describe air flow measurement units for HEPA filter systems. Specifically, the AG-1 standard does not differentiate between volumetric air flow in ACFM (actual cubic feet per minute)compared to mass flow measured in SCFM (standard cubic feet per minute). More importantly, the AG-1 standard has an overall deficiency for using HEPA filter devices at different air flow rates, temperatures, and altitudes. Technical Approach: The collection efficiency and pressure drops of 18 different HEPA filters will be measured over a range of flow rates, temperatures and altitudes. The experimental results will be compared to analytical scoping calculations. Three manufacturers have allocated six HEPA filters each for this effort. The 18 filters will be tested at two different flow rates, two different temperatures and two different altitudes. The 36 total tests will be conducted at two different facilities: the ATI Test facilities (Baltimore MD) and the Los Alamos National Laboratory (Los Alamos NM). The Radiation Protection RP-SVS group at Los Alamos has an aerosol wind tunnel that was originally designed to evaluate small air samplers. In 2010, modifications were started to convert the wind tunnel for HEPA filter testing. (Extensive changes were necessary for the required aerosol generators, HEPA test fixtures, temperature control devices and measurement capabilities.) To this date, none of these modification activities have been funded through a specific DOE or NNSA program. This is

  14. Soil washing treatability study

    SciTech Connect

    Krstich, M.

    1995-12-01

    Soil washing was identified as a viable treatment process option for remediating soil at the FEMP Environmental Management Project (FEMP). Little information relative to the specific application and potential effectiveness of the soil washing process exists that applies to the types of soil at the FEMP. To properly evaluate this process option in conjunction with the ongoing FEMP Remedial Investigation/Feasibility Study (RI/FS), a treatability testing program was necessary to provide a foundation for a detailed technical evaluation of the viability of the process. In August 1991, efforts were initiated to develop a work plan and experimental design for investigating the effectiveness of soil washing on FEMP soil. In August 1992, the final Treatability Study Work Plan for Operable Unit 5: Soil Washing (DOE 1992) was issued. This document shall be referenced throughout the remainder of this report as the Treatability Study Work Plan (TSWP). The purpose of this treatability study was to generate data to support initial screening and the detailed analysis of alternatives for the Operable Unit 5 FS.

  15. Synergistic anticancer effects of curcumin and resveratrol in Hepa1-6 hepatocellular carcinoma cells.

    PubMed

    Du, Qin; Hu, Bing; An, Hong-Mei; Shen, Ke-Ping; Xu, Ling; Deng, Shan; Wei, Meng-Meng

    2013-05-01

    Hepatocellular carcinoma remains one of the most prevalent malignancies worldwide. Curcuma aromatica and Polygonum cuspidatum are one of the commonly used paired-herbs for liver cancer treatment. Curcumin and resveratrol are the major anticancer constituents of Curcuma aromatica and Polygonum cuspidatum, respectively. Curcumin and resveratrol have been found to exhibit a synergistic anticancer effect in colon cancer. However, the combined effect of curcumin and resveratrol against hepatocellular carcinoma remains unknown. In the present study, we evaluated the combined effects of curcumin and resveratrol in hepatocellular carcinoma Hepa1-6 cells. The results showed that curcumin and resveratrol significantly inhibited the proliferation of Hepa1-6 cells in a dose- and time-dependent manner. The combination treatment of curcumin and resveratrol elicited a synergistic antiproliferative effect in Hepa1-6 cells. The apoptosis of Hepa1-6 cells induced by the combination treatment with curcumin and resveratrol was accompanied by caspase-3, -8 and -9 activation, which was completely abrogated by a pan caspase inhibitor, Z-VAD-FMK. Combination of curcumin and resveratrol upregulated intracellular reactive oxygen species (ROS) levels in Hepa1-6 cells. The ROS scavenger, NAC, partially attenuated the apoptosis and caspase activation induced by the combination treatment of curcumin and resveratrol. In addition, the combination of curcumin and resveratrol downregulated XIAP and survivin expression. These data suggest that the combination treatment of curcumin and resveratrol is a promising novel anticancer strategy for liver cancer. The present study also provides new insights into the effective mechanism of paired-herbs in traditional Chinese medicine. PMID:23446753

  16. Multi-Canister overpack internal HEPA filters

    SciTech Connect

    SMITH, K.E.

    1998-11-03

    The rationale for locating a filter assembly inside each Multi-Canister Overpack (MCO) rather than include the filter in the Cold Vacuum Drying (CVD) process piping system was to eliminate the potential for contamination to the operators, processing equipment, and the MCO. The internal HEPA filters provide essential protection to facility workers from alpha contamination, both external skin contamination and potential internal depositions. Filters installed in the CVD process piping cannot mitigate potential contamination when breaking the process piping connections. Experience with K-Basin material has shown that even an extremely small release can result in personnel contamination and costly schedule disruptions to perform equipment and facility decontamination. Incorporating the filter function internal to the MCO rather than external is consistent with ALARA requirements of 10 CFR 835. Based on the above, the SNF Project position is to retain the internal HEPA filters in the MCO design.

  17. A Survey of Mixed-Waste HEPA Filters in the DOE Complex

    SciTech Connect

    Felicione, F. S.; Barber, D. B.; Carney, K. P.

    2002-02-28

    A brief investigation was made to determine the quantities of spent, mixed-waste HEPA filters within the DOE Complex. The quantities of both the mixed-waste filters that are currently being generated, as well as the legacy mixed-waste filters being stored and awaiting disposition were evaluated. Seven DOE sites representing over 89% of the recent HEPA filter usage were identified. These sites were then contacted to determine the number of these filters that were likely destined to become mixed waste and to survey the legacy-filter quantities. Inquiries into the disposition plans for the filters were also made. It was determined that the seven sites surveyed possess approximately 500 m3 of legacy mixed-waste HEPA filters that will require processing, with an annual generation rate of approximately 25 m3. No attempt was made to extrapolate the results of this survey to the entire DOE Complex. These results were simply considered to be the lower bound of the totality of mixed-waste HEPA filters throughout the Complex. The quantities determined encourage the development of new treatment technologies for these filters, and provide initial data on which an appropriate capacity for a treatment process may be based.

  18. Degradation of HEPA filters exposed to DMSO

    SciTech Connect

    Bergman, W.; Wilson, K.; Larsen, G.; Lopez, R.; LeMay, J.

    1994-07-11

    Dimethyl sulfoxide (DMSO) sprays are being used to remove the high explosive (HE) from nuclear weapons in the process of their dismantlement. A boxed 50 cfm HEPA filter with an integral prefilter was exposed to DMSO vapor and aerosols that were generated by a spray nozzle to simulate conditions expected in the HE dissolution operation. After 198 hours of operation, the pressure drop of the filter had increased from 1.15 inches to 2.85 inches, and the efficiency for 0.3 {mu}m dioctyl sebacate (DOS) aerosols decreased from 99.992% to 98.6%. Most of the DMSO aerosols had collected as a liquid pool inside the boxed HEPA. The liquid was blown out of the filter exit with 100 cfm air flow at the end of the test. Since the filter still met the minimum allowed efficiency of 99.97% after 166 hours of exposure, we recommend replacing the filter every 160 hours of operation or sooner if the pressure drop increases by 50%. Examination of the filter showed that visible cracks appeared at the joints of the wooden frame and a portion of the sealant had pulled away from the frame. Since all of the DMSO will be trapped in the first HEPA filter, the second HEPA filter should not suffer from DMSO degradation. Thus the combined efficiency for the first filter (98.6%) and the second filter (99.97%) is 99.99996% for 0.3{mu}m particles. If the first filter is replaced prior to its degradation, each of the filters will have 99.97% efficiency, and the combined efficiency will be 99.999991%. The collection efficiency for DMSO/HE aerosols will be much higher because the particle size is much greater.

  19. Degradation of HEPA filters exposed to DMSO

    SciTech Connect

    Bergman, W.; Wilson, K.; Larsen, G.

    1995-02-01

    Dimethyl sulfoxide (DMSO) sprays are being used to remove the high explosive (HE) from nuclear weapons in the process of their dismantlement. A boxed 50 cmf HEPA filter with an integral prefilter was exposed to DMSO vapor and aerosols that were generated by a spray nozzle to simulate conditions expected in the HE dissolution operation. After 198 hours of operation, the pressure drop of the filter had increased form 1.15 inches to 2,85 inches, and the efficiency for 0.3 {mu}m dioctyl sebacate (DOS) aerosols decreased form 99.992% to 98.6%. Most of the DMSO aerosols had collected as a liquid pool inside the boxed HEPA. The liquid was blown out of the filter exit with 100 cmf air flow at the end of the test. Since the filter still met the minimum allowed efficiency of 99.97% after 166 hours of exposure, we recommend replacing the filter every 160 hours of operation or sooner if the pressure drop increases by 50%. Examination of the filter showed that visible cracks appeared at the joints of the wooden frame and a portion of the sealant had pulled away from the frame. Since all of the DMSO will be trapped in the first HEPA filter, the second HEPA filter should not suffer from DMSO degradation. Thus the combined efficiency for the first filter (98.6%) and the second filter (99.97%) is 99.99996% for 0.3 {mu}m particles. If the first filter is replaced prior to its degradation, each of the filters will have 99.97% efficiency, and the combined efficiency will be 99.999991%. The collection efficiency for DMSO/HE aerosols will be much higher because the particle size is much greater.

  20. Validation of the integrity of a HEPA filter system.

    PubMed

    Wang, Wei-Hsung

    2003-11-01

    The objective of this study was to establish a delayed air sampling method to verify the integrity of an existing HEPA filter system in a ventilated fume hood. (238U,232Th)O2 microspheres were generated to fabricate cement nuclear fuel pellets in a HEPA-filtered hood. To comply with the air effluent concentration limits by NRC, the capture efficiency of the HEPA filter was examined. An in-line isokinetic air sampling system was installed downstream of the HEPA filter. Utilizing a gas flow proportional counter, 212Pb was used as a surrogate to indicate any possible penetration of the (238U,232Th)O2 particles through the HEPA filter. Based on the experimental results, this delayed sampling method proved to be an easy and effective way to validate the integrity of the HEPA filter. PMID:14570263

  1. Comparison of water wash, trimming, and combined hot water and lactic acid treatments for reducing bacteria of fecal origin on beef carcasses.

    PubMed

    Castillo, A; Lucia, L M; Goodson, K J; Savell, J W; Acuff, G R

    1998-07-01

    Cleaning treatments, such as high-pressure water wash at 35 degrees C or trim, alone and combined with sanitizing treatments, such as hot water (95 degrees C at the source), warm (55 degrees C) 2% lactic acid spray, and combinations of these two sanitizing methods, were compared for their effectiveness in reducing inoculated numbers (5.0 to 6.0 log CFU/cm2) of Salmonella typhimurium, Escherichia coli O157:H7, aerobic plate counts, Enterobacteriaceae, total coliforms, thermotolerant coliforms, and generic E. coli on hot beef carcass surface areas in a model carcass spray cabinet. Log reductions in numbers of all tested organisms by water wash or trim alone were significantly smaller than the log reductions obtained by the different combined treatments. Regardless of the cleaning treatment (water wash or trim) or surface area, the range for mean log reductions by hot water was from 4.0 to > 4.8 log CFU/cm2, by lactic acid spray was from 4.6 to > 4.9 log CFU/cm2, by hot water followed by lactic acid spray was from 4.5 to > 4.9 log CFU/cm2, and by lactic acid spray followed by hot water was from 4.4 to > 4.6 log CFU/cm2, for S. typhimurium and E. coli O157:H7. Identical reductions were obtained for thermotolerant coliforms and generic E. coli. No differences in bacterial reductions were observed for different carcass surface regions. Water wash and trim treatments caused spreading of the contamination to other areas of the carcass surface while providing an overall reduction in fecal or pathogenic contamination on carcass surface areas. This relocated contamination after either water wash or trim was most effectively reduced by following with hot water and then lactic acid spray. This combined treatment yielded 0% positive samples for S. typhimurium, E. coli O157:H7, thermotolerant coliforms, and generic E. coli on areas outside the inoculated areas, whereas percent positive samples after applying other combined treatments ranged from 22 to 44% for S. typhimurium, 0 to

  2. Two-stage electrochemical treatment of bio-digested distillery spent wash using stainless steel and aluminum electrodes.

    PubMed

    Sharma, Pinki; Joshi, Himanshu; Srivastava, Vimal C

    2015-01-01

    The objective of this study was to determine the effectiveness of two-stage electro-coagulation (EC) process using multi-parameter optimization for treating bio-digested distillery spent wash by stainless steel (SS) and aluminum (Al) electrodes. Operating parameters have been optimized and treatment efficiency of SS and Al electrodes have been compared by central composite design of response surface analysis in terms of COD, color and total organic carbon (TOC) removal. Individual and interactive effects of four independent parameters namely initial pH (pHo: 2-10 and 4-10 for SS and Al electrodes, respectively), current density (j: 30.86-154.32 A m(-2)), inter-electrode distance (g: 0.5-2.5 cm) and electrolysis time (t: 30-150 min) on the COD, color and TOC removal efficiency were evaluated for both the electrodes. SS electrode was found to be more effective for the removal of COD, color and TOC with removal efficiencies of 70%, 93% and 72%, respectively, as compared to Al electrode, which showed respective removal efficiencies of 59%, 80% and 55%. A two-stage EC process was also conducted to study the predominance of different types of electrodes, and to increase the efficiency of EC process. Results shows that SS followed by Al electrode (with total COD, color and TOC removal efficiency of 81%, 94% and 78%, respectively) was found to be more effective than Al followed by SS electrode combination (with total COD, color and TOC removal efficiency of 78%, 89% and 76%, respectively). Present study shows that EC process can be used as an additional step to bio-methanation process so as to meet effluent discharge standards in distilleries. PMID:25837564

  3. Two-stage electrochemical treatment of bio-digested distillery spent wash using stainless steel and aluminum electrodes.

    PubMed

    Sharma, Pinki; Joshi, Himanshu; Srivastava, Vimal C

    2015-01-01

    The objective of this study was to determine the effectiveness of two-stage electro-coagulation (EC) process using multi-parameter optimization for treating bio-digested distillery spent wash by stainless steel (SS) and aluminum (Al) electrodes. Operating parameters have been optimized and treatment efficiency of SS and Al electrodes have been compared by central composite design of response surface analysis in terms of COD, color and total organic carbon (TOC) removal. Individual and interactive effects of four independent parameters namely initial pH (pHo: 2-10 and 4-10 for SS and Al electrodes, respectively), current density (j: 30.86-154.32 A m(-2)), inter-electrode distance (g: 0.5-2.5 cm) and electrolysis time (t: 30-150 min) on the COD, color and TOC removal efficiency were evaluated for both the electrodes. SS electrode was found to be more effective for the removal of COD, color and TOC with removal efficiencies of 70%, 93% and 72%, respectively, as compared to Al electrode, which showed respective removal efficiencies of 59%, 80% and 55%. A two-stage EC process was also conducted to study the predominance of different types of electrodes, and to increase the efficiency of EC process. Results shows that SS followed by Al electrode (with total COD, color and TOC removal efficiency of 81%, 94% and 78%, respectively) was found to be more effective than Al followed by SS electrode combination (with total COD, color and TOC removal efficiency of 78%, 89% and 76%, respectively). Present study shows that EC process can be used as an additional step to bio-methanation process so as to meet effluent discharge standards in distilleries.

  4. HEPA (high efficiency particulate air) filter optimization/implementation

    SciTech Connect

    Nenni, J.A.

    1988-02-10

    Prefilters were installed in high efficiency particularly air (HEPA) filter plenums at the Rocky Flats Plant. It was determined that prefiltration systems would extend the life of first-stage HEPA filters and reduce the amount of HEPA filter waste in the transuranic waste category. A remote handling system was designed to remove prefilters without entry into the plenum to reduce secondary waste and decrease exposure to Filter Technicians. 3 figs., 4 tabs.

  5. Experimental Investigation of In Situ Cleanable HEPA Filters

    SciTech Connect

    Hatcher, S.A.

    2001-04-11

    Savannah River Technology Center (SRTC) located at Westinghouse Savannah River Site (WSRS) is currently conducting research and development experimentation to develop a replacement of the conventional high efficiency particulate air (HEPA) filter system currently used by commercial industry and DOE facilities. It has been determined that a cleanable or regenerable HEPA filter system may be the most cost effective and efficient HEPA filter system to be considered for use in a more safe and reliable work environment.

  6. DOE standard: Quality assurance inspection and testing of HEPA filters

    SciTech Connect

    1999-02-01

    This standard establishes essential elements for the quality assurance inspection and testing of HEPA filters by US Department of Energy (DOE)-accepted Filter Test Facilities (FTF). The standard specifies HEPA filter quality assurance inspection and testing practices established in DOE-STD-3022-98, DOE HEPA Filter Test Program, and provides a basis for the preparation of written operating procedures for primary FTF functions.

  7. Effects of integrated treatment of nonthermal UV-C light and different antimicrobial wash on Salmonella enterica on plum tomatoes

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Produce contamination by foodborne pathogens remains a serious threat. This study investigated synergistic effects of ultraviolet-C and various active sanitizers’ washes against Salmonella enterica on plum tomatoes. A bacterial cocktail containing three serotypes of Salmonella enterica (S. Newport H...

  8. Qualification of box HEPA filters for nuclear applications

    SciTech Connect

    Bergman, W.; Larsen, G.; Wilson, K.; Rainer, F.

    1995-03-01

    We have successfully completed qualification tests on high efficiency particulate air (HEPA) filters that are encapsulated within a box and manufactured by American Air Filters. The qualification tests are required by the American Society of Mechanical Engineers Standard ASME N509 and the U.S. Military Standard MIL-F-51068 for HEPA filters to be used in nuclear applications. The qualification tests specify minimum filter efficiencies following exposure to heated air, overpressure, and rough handling. Prior to this study, no box HEPA filters from any manufacturer had been qualified despite their wide-spread use in Department of Energy (DOE) facilities. Box HEPA filters are not addressed in any of the existing HEPA standards and only briefly discussed in the Nuclear Air Cleaning Handbook.

  9. Utility of /sup 67/Ga scintigraphy and bronchial washings in the diagnosis and treatment of Pneumocystis carinii pneumonia in patients with the acquired immune deficiency syndrome

    SciTech Connect

    Tuazon, C.U.; Delaney, M.D.; Simon, G.L.; Witorsch, P.; Varma, V.M.

    1985-11-01

    Twenty patients with the acquired immune deficiency syndrome (AIDS) and suspected Pneumocystis carinii pneumonia were evaluated by /sup 67/Ga scintigraphy and fiberoptic bronchoscopy for initial diagnosis and response to therapy. Lung uptake of /sup 67/Ga was demonstrated in 100% of AIDS patients with P. carinii pneumonia, including those with subclinical infection. Fiberoptic bronchoscopy identified P. carinii in the bronchial washings of 100% of cases (19 patients), whereas only 13 of 16 (81%) patients had P. carinii in lung tissue obtained by transbronchial biopsy. Repeat fiberoptic bronchoscopy was performed in 16 of 20 patients. After 2 to 4 wk of therapy, P. carinii was identified in bronchial washings in 8 of 16 (50%) patients and in transbronchial biopsy in 1 of 10 (10%) patients examined. Bronchial washing has a higher yield than transbronchial biopsy in demonstrating P. carinii in patients with AIDS and may evolve as the procedure of choice in such patients. Based on the clinical course and results of /sup 67/Ga scintigraphy and fiberoptic bronchoscopy in AIDS patients with P. carinii pneumonia, optimal therapy may require at least 3 wk of treatment.

  10. Proper hand washing (image)

    MedlinePlus

    ... for proper hand washing include: Take off any jewelry. Hold your hands pointing down under warm water ... for proper hand washing include: Take off any jewelry. Hold your hands pointing down under warm water ...

  11. Technology development: HEPA filter service life test plan

    SciTech Connect

    Kirchner, K.N.; Cummings, K.G.; Leck, W.C.; Fretthold, J.K.

    1995-05-31

    Rocky Flats Environmental Technology Site (the Site) has approximately 10,000 High Efficiency Particulate Air (HEPA) Filters installed in a variety of filter plenums. These ventilation/filtration plenum systems are used to control the release of airborne particulate contaminates to the environment during normal operations and also during potential design-based accidents. The operational integrity of the HEPA filter plenums is essential to maintaining the margins of safety as required by building specific Final Safety Analysis Reports (FSARS) for protection of the public and environment. An Unreviewed Safety Question Determination (USQD), USDQ-RFP94.0615-ARS, was conducted in 1994 addressing the potential inadequacy of the safety envelope for Protected Area building HEPA plenums. While conducting this USQD, questions were raised concerning the maximum service life criteria for HEPA filters. Accident scenarios in existing FSARs identify conditions that could potentially cause plugging or damage of down stream HEPA filters as a result of impaction from failed filters. Additionally, available data indicates that HEPA filters experience structural degradation due to the effects of age. The Unresolved Safety Question (USQ) compensatory measures thus require testing and analysis of used HEPA filters in order to determine and implement service life criteria.

  12. Hydrology of Cornfield Wash area and effects of land treatment practices, Sandoval County, New Mexico, 1951-60

    USGS Publications Warehouse

    Burkham, D.E.

    1967-01-01

    The collection of runoff and sediment data was the primary objective of the 10-year (1951-60) study in the Cornfield Wash basin, which has an area of 21.3 square miles. However, reconnaissance investigations also were made of (1) precipitation; (2) the effects of reservoirs on runoff, erosion, and sediment yield; (3) the effects of range pitting on runoff, sediment, and vegetation yields; and (4) the effects of wire sediment barriers on sediment accumulations. Precipitation averaged 6.07 inches for the warm season (May 1 through October 31). From 1951 to 1955 much of the precipitation came in short torrential downpours. Since 1955, precipitation usually has been of lower intensity, resulting in a low runoff-precipitation ratio. The total composite inflow to the 19 reservoirs in the Cornfield Wash basin--12 constructed in 1950 and 7 constructed from 1953 to 1956--was 5,720 acre-feet. The reservoirs permanently retained 1,370 acre-feet of water, 43 percent of which was apparently lost by evaporation. The average seasonal runoff (1951-59) from the ephemeral streams of the Cornfield Wash basin and nearby watersheds can be expressed, with a high coefficient of correlation, by the equation: runoff = 29.4 (area) 0.82 acre-feet. This relation suggests that there is a good correlation between the size of the drainage basin and the basin characteristics that most influence travel time of runoff. Comparisons of readily measurable basin characteristics that influence travel time indicate: 1. Land slope is proportional to (area) .0.035; 2. Length of longest watercourse is proportional to (area) 0.52; 3. Distance along the longest watercourse from gaging station to a point opposite the center of drainage basin is proportional to (area)0.52; and 4. Equivalent channel slope is proportional to (area)- 0.027. Except for land slope, the coefficients of correlation for each of the basin characteristics-area relations were relatively high. The correlation between seasonal runoff (1951

  13. Bacterial Selection during the Formation of Early-Stage Aerobic Granules in Wastewater Treatment Systems Operated Under Wash-Out Dynamics

    PubMed Central

    Weissbrodt, David G.; Lochmatter, Samuel; Ebrahimi, Sirous; Rossi, Pierre; Maillard, Julien; Holliger, Christof

    2012-01-01

    Aerobic granular sludge is attractive for high-rate biological wastewater treatment. Biomass wash-out conditions stimulate the formation of aerobic granules. Deteriorated performances in biomass settling and nutrient removal during start-up have however often been reported. The effect of wash-out dynamics was investigated on bacterial selection, biomass settling behavior, and metabolic activities during the formation of early-stage granules from activated sludge of two wastewater treatment plants (WWTP) over start-up periods of maximum 60 days. Five bubble-column sequencing batch reactors were operated with feast-famine regimes consisting of rapid pulse or slow anaerobic feeding followed by aerobic starvation. Slow-settling fluffy granules were formed when an insufficient superficial air velocity (SAV; 1.8 cm s−1) was applied, when the inoculation sludge was taken from a WWTP removing organic matter only, or when reactors were operated at 30°C. Fast-settling dense granules were obtained with 4.0 cm s−1 SAV, or when the inoculation sludge was taken from a WWTP removing all nutrients biologically. However, only carbon was aerobically removed during start-up. Fluffy granules and dense granules were displaying distinct predominant phylotypes, namely filamentous Burkholderiales affiliates and Zoogloea relatives, respectively. The latter were predominant in dense granules independently from the feeding regime. A combination of insufficient solid retention time and of leakage of acetate into the aeration phase during intensive biomass wash-out was the cause for the proliferation of Zoogloea spp. in dense granules, and for the deterioration of BNR performances. It is however not certain that Zoogloea-like organisms are essential in granule formation. Optimal operation conditions should be elucidated for maintaining a balance between organisms with granulation propensity and nutrient removing organisms in order to form granules with BNR activities in short

  14. Bacterial Selection during the Formation of Early-Stage Aerobic Granules in Wastewater Treatment Systems Operated Under Wash-Out Dynamics.

    PubMed

    Weissbrodt, David G; Lochmatter, Samuel; Ebrahimi, Sirous; Rossi, Pierre; Maillard, Julien; Holliger, Christof

    2012-01-01

    Aerobic granular sludge is attractive for high-rate biological wastewater treatment. Biomass wash-out conditions stimulate the formation of aerobic granules. Deteriorated performances in biomass settling and nutrient removal during start-up have however often been reported. The effect of wash-out dynamics was investigated on bacterial selection, biomass settling behavior, and metabolic activities during the formation of early-stage granules from activated sludge of two wastewater treatment plants (WWTP) over start-up periods of maximum 60 days. Five bubble-column sequencing batch reactors were operated with feast-famine regimes consisting of rapid pulse or slow anaerobic feeding followed by aerobic starvation. Slow-settling fluffy granules were formed when an insufficient superficial air velocity (SAV; 1.8 cm s(-1)) was applied, when the inoculation sludge was taken from a WWTP removing organic matter only, or when reactors were operated at 30°C. Fast-settling dense granules were obtained with 4.0 cm s(-1) SAV, or when the inoculation sludge was taken from a WWTP removing all nutrients biologically. However, only carbon was aerobically removed during start-up. Fluffy granules and dense granules were displaying distinct predominant phylotypes, namely filamentous Burkholderiales affiliates and Zoogloea relatives, respectively. The latter were predominant in dense granules independently from the feeding regime. A combination of insufficient solid retention time and of leakage of acetate into the aeration phase during intensive biomass wash-out was the cause for the proliferation of Zoogloea spp. in dense granules, and for the deterioration of BNR performances. It is however not certain that Zoogloea-like organisms are essential in granule formation. Optimal operation conditions should be elucidated for maintaining a balance between organisms with granulation propensity and nutrient removing organisms in order to form granules with BNR activities in short

  15. Combined mild soil washing and compost-assisted phytoremediation in treatment of silt loams contaminated with copper, nickel, and chromium.

    PubMed

    Sung, Menghau; Lee, Chi-Yi; Lee, Suen-Zone

    2011-06-15

    A new soil remediation option, combining the soil washing process using pure water followed by the compost-assisted phytoextraction, is evaluated using silt loams contaminated with plating wastewater containing Cu, Ni, and Cr. Plants utilized in this study are the rapeseeds, sunflowers, tomatoes, and soapworts. Phytoextraction operation was carried out in pot experiments over a period of 4 months. Metal concentrations in roots and shoots of plants were analyzed upon completion of each pot experiment. Hypothesis testing was employed in assessing the significance of difference in the experimental data. Results indicated that the rapeseed, a hyperaccumulator, is most effective in extracting metals from the compost-amended silt loams. The fast-growing sunflowers and tomatoes are comparable to rapeseeds in accumulating metals despite their relatively low metal concentrations in tissues. Bioaccumulation coefficients obtained for all plants are less than one, indicating that phytostabilization rather than phytoextraction is the dominant mechanism at this simulated final-phase condition.

  16. Combined mild soil washing and compost-assisted phytoremediation in treatment of silt loams contaminated with copper, nickel, and chromium.

    PubMed

    Sung, Menghau; Lee, Chi-Yi; Lee, Suen-Zone

    2011-06-15

    A new soil remediation option, combining the soil washing process using pure water followed by the compost-assisted phytoextraction, is evaluated using silt loams contaminated with plating wastewater containing Cu, Ni, and Cr. Plants utilized in this study are the rapeseeds, sunflowers, tomatoes, and soapworts. Phytoextraction operation was carried out in pot experiments over a period of 4 months. Metal concentrations in roots and shoots of plants were analyzed upon completion of each pot experiment. Hypothesis testing was employed in assessing the significance of difference in the experimental data. Results indicated that the rapeseed, a hyperaccumulator, is most effective in extracting metals from the compost-amended silt loams. The fast-growing sunflowers and tomatoes are comparable to rapeseeds in accumulating metals despite their relatively low metal concentrations in tissues. Bioaccumulation coefficients obtained for all plants are less than one, indicating that phytostabilization rather than phytoextraction is the dominant mechanism at this simulated final-phase condition. PMID:21531509

  17. Alternative HEPA Filter Full-Scale Single Element Testing

    SciTech Connect

    Adamson, D.J.

    2003-01-15

    Conventional disposable glass-fiber high efficiency particulate air (HEPA) filters are used throughout the Department of Energy complex in various process systems. Alternative filter media is being addressed that would have a long life on the HLW tanks.

  18. Specification for HEPA filters used by DOE contractors

    SciTech Connect

    1997-01-01

    This standard establishes specification and testing requirements for High Efficiency Particulate Air (HEPA) filters procured to provide personnel and environmental protection when installed in DOE nuclear facilities. The standard specifies minimum requirements to be included in contractor specifications.

  19. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTHWEST. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTHWEST. - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  20. The effect of media area on the dust holding capacity of deep pleat HEPA filters

    SciTech Connect

    Dyment, J.; Loughborough, D.

    1997-08-01

    The high potential cost of storage, treatment and disposal of radioactive wastes places a premium on the longevity of installed HEPA filters in situations in radioactive processing facilities where dust capacity is a life determining factor. Previous work investigated the dust holding capacity v pressure drop characteristics of different designs of HEPA filter and also the effect of using graded density papers. This paper records an investigation of the effect of media area variation on the dust holding capacity of the {open_quotes}deep-pleat{close_quotes} design of HEPA filter. As in the previously reported work two test dusts (carbon black and sub micron sodium chloride) in the range (0.15 - 0.4{mu}m) were used. Media area adjustment was effected by varying the number of separators within the range 60 - 90. Results with the coarser dust allowed an optimum media area to be identified. Media areas greater or smaller than this optimum retained less dust than the optimum for the same terminal pressure drop. Conversely with the finer sodium chloride aerosol the dust holding capacity continued to increase up to the maximum area investigated. 7 refs., 4 figs.

  1. Wash water recovery system

    NASA Technical Reports Server (NTRS)

    Deckman, G.; Rousseau, J. (Editor)

    1973-01-01

    The Wash Water Recovery System (WWRS) is intended for use in processing shower bath water onboard a spacecraft. The WWRS utilizes flash evaporation, vapor compression, and pyrolytic reaction to process the wash water to allow recovery of potable water. Wash water flashing and foaming characteristics, are evaluated physical properties, of concentrated wash water are determined, and a long term feasibility study on the system is performed. In addition, a computer analysis of the system and a detail design of a 10 lb/hr vortex-type water vapor compressor were completed. The computer analysis also sized remaining system components on the basis of the new vortex compressor design.

  2. Experimental investigation of in situ cleanable HEPA filter

    SciTech Connect

    Adamson, D.J.

    1999-07-01

    The Westinghouse Savannah River Company located at the Savannah River Site (SRS) in Aiken, South Carolina is currently testing the feasibility of developing an in situ cleanable high efficiency particulate air (HEPA) filter system. Sintered metal filters are being tested for regenerability or cleanability in simulated conditions found in a high level waste (HLW) tank ventilation system. The filters are being challenged using materials found in HLW tanks. HLW simulated salt, HLW simulated sludge and South Carolina road dust. Various cleaning solutions have been used to clean the filters in situ. The tanks are equipped with a ventilation system to maintain the tank contents at negative pressure to prevent the release of radioactive material to the environment. This system is equipped with conventional disposable glass-fiber HEPA filter cartridges. Removal and disposal of these filters is not only costly, but subjects site personnel to radiation exposure and possible contamination. A test apparatus was designed to simulate the ventilation system of a HLW tank with an in situ cleaning system. Test results indicate that the Mott sintered metal HEPA filter is suitable as an in situ cleanable or regenerable HEPA filter. Data indicates that high humidity or water did not effect the filter performance and the sintered metal HEPA filter was easily cleaned numerous times back to new filter performance by an in situ spray system. The test apparatus allows the cleaning of the soiled HEPA filters to be accomplished without removing the filters from process. This innovative system would eliminate personnel radiation exposure associated with removal of contaminated filters and the high costs of filter replacement and disposal. The results of these investigations indicate that an in situ cleanable HEPA filter system for radioactive and commercial use could be developed and manufactured.

  3. HEPA Filter Performance under Adverse Conditions

    SciTech Connect

    Parsons, Michael; Hogancamp, Kristina; Alderman, Steven; Waggoner, Charles

    2007-07-01

    This study involved challenging nuclear grade high-efficiency particulate air (HEPA) filters under a variety of conditions that can arise in Department of Energy (DOE) applications such as: low or high RH, controlled and uncontrolled challenge, and filters with physically damaged media or seals (i.e., leaks). Reported findings correlate filter function as measured by traditional differential pressure techniques in comparison with simultaneous instrumental determination of up and down stream PM concentrations. Additionally, emission rates and failure signatures will be discussed for filters that have either failed or exceeded their usable lifetime. Significant findings from this effort include the use of thermocouples up and down stream of the filter housing to detect the presence of moisture. Also demonstrated in the moisture challenge series of tests is the effect of repeated wetting of the filter. This produces a phenomenon referred to as transient failure before the tensile strength of the media weakens to the point of physical failure. An evaluation of the effect of particle size distribution of the challenge aerosol on loading capacity of filters is also included. Results for soot and two size distributions of KCl are reported. Loading capacities for filters ranged from approximately 70 g of soot to nearly 900 g for the larger particle size distribution of KCl. (authors)

  4. 3. VIEW LOOKING NORTH AT CHINA WASH FLUME SHOWING WASH ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    3. VIEW LOOKING NORTH AT CHINA WASH FLUME SHOWING WASH - San Carlos Irrigation Project, China Wash Flume, Main (Florence-Case Grande) Canal at Station 137+00, T4S, R10E, S14, Coolidge, Pinal County, AZ

  5. Alternative Antimicrobial Commercial Egg Washing Procedures.

    PubMed

    Hudson, Lauren K; Harrison, Mark A; Berrang, Mark E; Jones, Deana R

    2016-07-01

    Commercial table eggs are washed prior to packaging. Standard wash procedures use an alkaline pH and warm water. If a cool water method could be developed that would still provide a microbiologically safe egg, the industry may save energy costs associated with water heating. Four wash procedures were evaluated for Salmonella reduction: pH 11 at 48.9°C (industry standard), pH 11 at ambient temperature (∼20°C), pH 6 at 48.9°C, and pH 6 at ambient temperature. Alkaline washes contained potassium hydroxide-based detergent, while pH 6 washes contained approximately 200 ppm of chlorine and a proprietary chlorine stabilizer (T-128). When eggs were inoculated by immersion in a cell suspension of Salmonella Enteritidis and Salmonella Typhimurium, all treatments resulted in a slight and similar reduction of Salmonella numbers (approximately 0.77 log CFU/ml of shell emulsion reduction). When eggs were inoculated by droplet on the shell surface, Salmonella counts were reduced by approximately 5 log CFU when washed with chlorine plus the chlorine stabilizer at both temperatures and with the alkaline wash at the high temperature. The reductions in Salmonella by these treatments were not significantly (P > 0.05) different from each other but were significantly (P < 0.05) more than the reduction observed for the 20°C alkaline treatment and 20°C control water treatments. Ambient temperature acidic washes reduced Salmonella contamination to the same degree as the standard pH 11 warm water wash and may be a viable option to reduce cost, increase shelf life, and slow pathogen growth in and on shell eggs. PMID:27357042

  6. Alternative Antimicrobial Commercial Egg Washing Procedures.

    PubMed

    Hudson, Lauren K; Harrison, Mark A; Berrang, Mark E; Jones, Deana R

    2016-07-01

    Commercial table eggs are washed prior to packaging. Standard wash procedures use an alkaline pH and warm water. If a cool water method could be developed that would still provide a microbiologically safe egg, the industry may save energy costs associated with water heating. Four wash procedures were evaluated for Salmonella reduction: pH 11 at 48.9°C (industry standard), pH 11 at ambient temperature (∼20°C), pH 6 at 48.9°C, and pH 6 at ambient temperature. Alkaline washes contained potassium hydroxide-based detergent, while pH 6 washes contained approximately 200 ppm of chlorine and a proprietary chlorine stabilizer (T-128). When eggs were inoculated by immersion in a cell suspension of Salmonella Enteritidis and Salmonella Typhimurium, all treatments resulted in a slight and similar reduction of Salmonella numbers (approximately 0.77 log CFU/ml of shell emulsion reduction). When eggs were inoculated by droplet on the shell surface, Salmonella counts were reduced by approximately 5 log CFU when washed with chlorine plus the chlorine stabilizer at both temperatures and with the alkaline wash at the high temperature. The reductions in Salmonella by these treatments were not significantly (P > 0.05) different from each other but were significantly (P < 0.05) more than the reduction observed for the 20°C alkaline treatment and 20°C control water treatments. Ambient temperature acidic washes reduced Salmonella contamination to the same degree as the standard pH 11 warm water wash and may be a viable option to reduce cost, increase shelf life, and slow pathogen growth in and on shell eggs.

  7. Effect of DOP heterodispersion on HEPA-filter-penetration measurements

    SciTech Connect

    Bergman, W.; Biermann, A.

    1984-08-09

    The accuracy of the standard US test method for certifying High-Efficiency Particulate Air (HEPA) filters has been in question since the finding by Hinds, et al. that the dioctyl phthalate (DOP) aerosol used in the test is not monodisperse as had been assumed and that particle-size analyzers, or owls, could not distinguish between different particle-size distributions with the same owl reading. We have studied theoretically and experimentally the filter efficiency for different DOP size distributions with the same owl reading. Our studies show that the effect of varying DOP size distributions on the measured HEPA-filter penetration depends on the light-scattering-photometer response and on the HEPA-filter penetration curve, both measured as a function of particle size. HEPA-filter penetration for a heterodisperse DOP aerosol may be increased, decreased, or remain the same when compared to the filter penetration for monodisperse aerosols. Using experimental HEPA-filter penetration and photometer response curves, we show that heterodisperse DOP aerosols (D/sub cmd/ 0.19 and sigma g = 1.4) yield 24% lower penetrations than that for monodisperse DOP aerosols (D/sub cmd/ = 0.3 and sigma g = 1.0). This surprisingly small effect of the DOP heterodispersion on HEPA-filter penetration is due to the response function of the owl that is similar to the response of the photometer. Changes in the particle-size distribution are therefore seen in a similar fashion by both the photometer and the owl. We also show that replacing the owl with modern particle-size spectrometers may lead to large errors in filter penetration because the particle-size spectrometers do not provide measurements that correspond to the photometer measurements. 15 references, 16 figures.

  8. EFRT M-12 Issue Resolution: Solids Washing

    SciTech Connect

    Baldwin, David L.; Schonewill, Philip P.; Toth, James J.; Huckaby, James L.; Eslinger, Paul W.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

    2009-08-14

    Pacific Northwest National Laboratory (PNNL) has been tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes.” The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. Two operating scenarios were evaluated for the ultrafiltration process (UFP) and leaching operations. The first scenario has caustic leaching performed in the UFP-VSL-T01A/B ultrafiltration feed vessels, identified as Integrated Test A. The second scenario has caustic leaching conducted in the UFP-VSL-T02A ultrafiltration feed preparation vessel, identified as Integrated Test B. Washing operations in PEP Integrated Tests A and B were conducted successfully as per the approved run sheets. However, various minor instrumental problems occurred, and some of the process conditions specified in the run sheet were not met during the wash operations, such as filter-loop flow-rate targets not being met. Five analytes were selected based on full solubility and monitored in the post-caustic-leach wash as successful indicators of washing efficiency. These were aluminum, sulfate, nitrate, nitrite, and free hydroxide. Other analytes, including sodium, oxalate, phosphate, and total dissolved solids, showed indications of changing solubility; therefore, they were unsuitable for monitoring washing efficiency. In the post-oxidative-leach wash, two analytes with full solubility were selected as suitable indicators of washing

  9. Quality assurance testing of HEPA filters and respirator canisters

    SciTech Connect

    Not Available

    1984-06-22

    This standard covers requirements for the quality assurance inspection and testing of HEPA filters and respirator canisters by the US Department of Energy (DOE) Filter Test Facilities (FTFs) at Oak Ridge, Tennessee; Golden, Colorado; and Richland, Washington. The standard provides a basis for the preparation of written procedures for conducting primary FTF functions. These standards apply only to filters used at DOE installations for environmental protection purposes. These filters are described as Type B filters in Institute of Environmental Sciences HEPA Filter Practices, IES Designation RP-CC-001.

  10. HEPA filter leaching concept validation trials at the Idaho Chemical Processing Plant

    SciTech Connect

    Chakravartty, A.C.

    1995-04-01

    The enclosed report documents six New Waste Calcining Facility (NWCF) HEPA filter leaching trials conducted at the Idaho Chemical Processing Plant using a filter leaching system to validate the filter leaching treatment concept. The test results show that a modified filter leaching system will be able to successfully remove both hazardous and radiological constituents to RCRA disposal levels. Based on the success of the filter leach trials, the existing leaching system will be modified to provide a safe, simple, effective, and operationally flexible filter leaching system.

  11. Wash water solids removal system study

    NASA Technical Reports Server (NTRS)

    1974-01-01

    During wash water purification, surfactants tend to precipitate and foul the RO membranes, causing water flux decline and loss of salt rejection. The use of 165 to 190 ppm ferric chloride and optionally 0.25 to 1.0 ppm polymeric flocculate precipitates 92 to 96 percent of the surfactant from an Olive Leaf Soap based wash water. Crossflow filtration and pressure filtration yield good soap rejection at high water flux rates. Post-treatment of the chemically pretreated and filtered wash water with activated charcoal removes the residual soap down to an undetectable level.

  12. Single-stage fermentation process for high-value biohythane production with the treatment of distillery spent-wash.

    PubMed

    Pasupuleti, Suresh Babu; Venkata Mohan, S

    2015-01-01

    The current communication reports the development of a single-stage biosystem for biohythane production from wastewater treatment. A semi-pilot scale bioreactor with 34 L capacity was used for this study. Maximum biohythane production of 147.5 ± 2.4 L was observed after five cycles of operation with production rate of 4.7 ± 0.1L/h. The biohythane composition (H2/(H2+CH4)) varied from 0.60 to 0.23 during stabilized fifth cycle of operation. During each cycle of operation, higher H2 fraction was noticed within 12h of cycle period followed by CH4 production for rest of operation (36 h). During biohythane production, COD removal efficiency of 60 ± 5% (SDR, 29.0 ± 1.9 kg CODr/m(3)-day) was also achieved. The synergistic function of volatile fatty acids (VFA) production and consumption during process in hybrid biosystem played vital role on the composition of biohythane. The single-stage biosystem facilitates production of high valued and cost efficient biofuel (biohythane) with fewer controls than individual acidogenic and methanogenic processes. PMID:25889805

  13. ALTERNATE HIGH EFFICIENCY PARTICULATE AIR (HEPA) FILTRATION SYSTEM

    SciTech Connect

    Bruce Bishop; Robert Goldsmith; Karsten Nielsen; Phillip Paquette

    2002-08-16

    In Phase IIA of this project, CeraMem has further developed and scaled up ceramic HEPA filters that are appropriate for use on filtration of vent gas from HLW tanks at DOE sites around the country. This work included procuring recrystallized SiC monoliths, developing membrane and cement materials, and defining a manufacturing process for the production of prototype full sizes HEPA filters. CeraMem has demonstrated that prototype full size filters can be manufactured by producing 9 full size filters that passed DOP aerosol testing at the Oak Ridge Filter Test Facility. One of these filters was supplied to the Savannah River Technical Center (SRTC) for process tests using simulated HLW tank waste. SRTC has reported that the filter was regenerable (with some increase in pressure drop) and that the filter retained its HEPA retention capability. CeraMem has also developed a Regenerable HEPA Filter System (RHFS) design and acceptance test plan that was reviewed by DOE personnel. The design and acceptance test plan form the basis of the system proposal for follow-on work in Phase IIB of this project.

  14. HEPA/vaccine plan for indoor anthrax remediation.

    PubMed

    Wein, Lawrence M; Liu, Yifan; Leighton, Terrance J

    2005-01-01

    We developed a mathematical model to compare 2 indoor remediation strategies in the aftermath of an outdoor release of 1.5 kg of anthrax spores in lower Manhattan. The 2 strategies are the fumigation approach used after the 2001 postal anthrax attack and a HEPA/vaccine plan, which relies on HEPA vacuuming, HEPA air cleaners, and vaccination of reoccupants. The HEPA/vaccine approach leads to few anthrax cases among reoccupants if applied to all but the most heavily contaminated buildings, and recovery is much faster than under the decades-long fumigation plan. Only modest environmental sampling is needed. A surge capacity of 10,000 to 20,000 Hazmat workers is required to perform remediation within 6 to 12 months and to avoid permanent mass relocation. Because of the possibility of a campaign of terrorist attacks, serious consideration should be given to allowing or encouraging voluntary self-service cleaning of lightly contaminated rooms by age-appropriate, vaccinated, partially protected (through masks or hoods) reoccupants or owners. PMID:15705325

  15. Pilot-scale tests of HEME and HEPA dissolution process

    SciTech Connect

    Qureshi, Z.H.; Strege, D.K.

    1994-06-01

    A series of pilot-scale demonstration tests for the dissolution of High Efficiency Mist Eliminators (HEME`s) and High Efficiency Particulate Airfilters (HEPA) were performed on a 1/5th linear scale. These fiberglass filters are to be used in the Defense Waste Processing Facility (DWPF) to decontaminate the effluents from the off-gases generated during the feed preparation process and vitrification. When removed, these filters will be dissolved in the Decontamination Waste Treatment Tank (DWTT) using 5 wt% NaOH solution. The contaminated fiberglass is converted to an aqueous stream which will be transferred to the waste tanks. The filter metal structure will be rinsed with process water before its disposal as low-level solid waste. The pilot-scale study reported here successfully demonstrated a simple one step process using 5 wt% NaOH solution. The proposed process requires the installation of a new water spray ring with 30 nozzles. In addition to the reduced waste generated, the total process time is reduced to 48 hours only (66% saving in time). The pilot-scale tests clearly demonstrated that the dissolution process of HEMEs has two stages - chemical digestion of the filter and mechanical erosion of the digested filter. The digestion is achieved by a boiling 5 wt% caustic solutions, whereas the mechanical break down of the digested filter is successfully achieved by spraying process water on the digested filter. An alternate method of breaking down the digested filter by increased air sparging of the solution was found to be marginally successful are best. The pilot-scale tests also demonstrated that the products of dissolution are easily pumpable by a centrifugal pump.

  16. Perfusion flow rate substantially contributes to the performance of the HepaRG-AMC-bioartificial liver.

    PubMed

    Nibourg, Geert A A; Boer, Justin D; van der Hoeven, Tessa V; Ackermans, Mariëtte T; van Gulik, Thomas M; Chamuleau, Robert A F M; Hoekstra, Ruurdtje

    2012-12-01

    Bioartificial livers (BALs) are bioreactors containing liver cells that provide extracorporeal liver support to liver-failure patients. Theoretically, the plasma perfusion flow rate through a BAL is an important determinant of its functionality. Low flow rates can limit functionality due to limited substrate availability, and high flow rates can induce cell damage. This hypothesis was tested by perfusing the AMC-BAL loaded with the liver cell line HepaRG at four different medium flow rates (0.3, 1.5, 5, and 10 mL/min). Hepatic functions ammonia elimination, urea production, lactate consumption, and 6β-hydroxylation of testosterone showed 2-20-fold higher rates at 5 mL/min compared to 0.3 mL/min, while cell damage remained stable. However, at 10 mL/min cell damage was twofold higher, and maximal hepatic functionality was not changed, except for an increase in lactate elimination. On the other hand, only a low flow rate of 0.3 mL/min allowed for an accurate measurement of the ammonia and lactate mass balance across the bioreactor, which is useful for monitoring the BAL's condition during treatment. These results show that (1) the functionality of a BAL highly depends on the perfusion rate; (2) there is a universal optimal flow rate based on various function and cell damage parameters (5 mL/min for HepaRG-BAL); and (3) in the current set-up the mass balance of substrate, metabolite, or cell damage markers between in-and out-flow of the bioreactor can only be determined at a suboptimal, low, perfusion rate (0.3 mL/min for HepaRG-BAL).

  17. Solvent wash solution

    DOEpatents

    Neace, James C.

    1986-01-01

    Process for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 volume percent of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  18. Solvent wash solution

    DOEpatents

    Neace, J.C.

    1984-03-13

    A process is claimed for removing diluent degradation products from a solvent extraction solution, which has been used to recover uranium and plutonium from spent nuclear fuel. A wash solution and the solvent extraction solution are combined. The wash solution contains (a) water and (b) up to about, and including, 50 vol % of at least one-polar water-miscible organic solvent based on the total volume of the water and the highly-polar organic solvent. The wash solution also preferably contains at least one inorganic salt. The diluent degradation products dissolve in the highly-polar organic solvent and the organic solvent extraction solvent do not dissolve in the highly-polar organic solvent. The highly-polar organic solvent and the extraction solvent are separated.

  19. Reduction of Salmonella enterica contamination on grape tomatoes by washing with thyme oil, thymol, and carvacrol as compared with chlorine treatment.

    PubMed

    Lu, Yingjian; Wu, Changqing

    2010-12-01

    In recent years, multistate outbreaks of Salmonella enterica serovars were traced to tomatoes and resulted in serious economic loss for the tomato industry and decreased consumer confidence in the safety of tomato produce. Purified compounds derived from essential oils such as thymol and carvacrol had wide inhibitory effects against foodborne pathogens including Salmonella. The objective of this study was to determine the antimicrobial activities of thymol, carvacrol, and thyme oil against Salmonella on grape tomatoes. Surface-inoculated grape tomatoes were washed with 4% ethanol, 200 ppm of chlorine, or one of six washing solutions (thymol [0.2 and 0.4 mg/ml], thyme oil [1 and 2 mg/ml], and carvacrol [0.2 and 0.4 mg/ml]) for 5 or 10 min. There was no significant difference in the reduction of S. enterica serovars when different washing times were used (P > 0.05). Thymol (especially at the concentration of 0.4 mg/ml) was the most effective (P < 0.05) among the three natural antimicrobial agents, which achieved >4.1-log reductions of S. enterica serovars Typhimurium, Kentucky, Senftenberg, and Enteritidis on grape tomatoes after a 5-min washing and >4.3-log reductions after a 10-min washing. A >4.6-log reduction in the S. enterica populations in comparison to control was observed with the use of thymol solutions. The uses of these antimicrobial agents achieved significant log reductions of Salmonella on inoculated grape tomatoes and decreased dramatically the risk of potential transmission of pathogens from tomatoes to washing solutions. None of these antimicrobial agents decreased the total phenolic and ascorbic acid content, nor did any of them change the color and pH values or affect the taste, aroma, or visual quality of grape tomatoes. Therefore, 0.4 mg/ml thymol has great potential to be an alternative to chlorine-based washing solution for fresh produce. PMID:21219747

  20. Wash Your Hands

    MedlinePlus

    ... do if you don't have soap and clean, running water? Washing hands with soap and water is the ... specific questions. More Information CDC's Handwashing Work Handwashing: Clean Hands Save Lives Hand Hygiene in Healthcare Settings Water-related Hygiene Hand Hygiene to Help Prevent Flu ...

  1. Domestic wash water reclamation

    NASA Technical Reports Server (NTRS)

    Hall, J. B., Jr.; Batten, C. E.; Wilkins, J. R.

    1974-01-01

    System consists of filtration unit, reverse-osmosis module, tanks, pumps, plumbing, and various gauges, meters, and valves. After water is used in washing machine or shower, it is collected in holding tank. Water is pumped through series of five particulate filters. Pressure tank supplies processed water to commode water closet.

  2. The two-phase leaching of Pb, Zn and Cd contaminated soil using EDTA and electrochemical treatment of the washing solution.

    PubMed

    Finzgar, Neza; Lestan, Domen

    2008-11-01

    The feasibility of a novel two-phase method for remediation of Pb (1374 mg kg(-1)), Zn (1007 mg kg(-1)), and Cd (9.1 mg kg(-1)) contaminated soil was evaluated. In the first phase we used EDTA for leaching heavy metals from the soil. In the second phase we used an electrochemical advanced oxidation process (EAOP) for the treatment and reuse of washing solution for soil rinsing (removal of the soil-retained, chelant-mobilized metallic species). In EAOP, a boron-doped diamond anode was used for the generation of hydroxyl radicals and oxidative decomposition of EDTA-metal complexes at a constant current density (15 mA cm(-2)). The released metals were removed from the solution by filtration as insoluble participate and by electro-deposition on the cathode. Four consecutive additions of 5.0 mm ol kg(-1) EDTA (total 20 mmol kg(-1)) removed 44% Pb, 14% Zn and 35% Cd from the soil. The mobility of the Pb, Zn and Cd (Toxicity Characteristic Leaching Procedure) left in the soil after remediation was reduced by 1.6, 3.4 and 1.5 times, respectively. The Pb oral availability (Physiologically Based Extraction Test) in the simulated stomach phase was reduced by 2.4 and in the intestinal phase by 1.7 times. The discharge solution was clear, almost colorless, with pH 7.73 and 0.47 mg L(-1) Pb, 1.03 mg L(-1) Zn, bellow the limits of quantification of Cd and 0.023 mM EDTA. The novel method enables soil leaching with small water requirements and no wastewater generation or other emissions into the environment. PMID:18762318

  3. A review of DOE HEPA filter component test activities

    SciTech Connect

    Slawski, J.W.; Bresson, J.F.; Scripsick, R.C.

    1997-08-01

    All HEPA filters purchased for installation in DOE nuclear facilities are required to be tested at a Filter Test Facility (FTF) prior to installation. The number of HEPA filters purchased by DOE has been reduced so much that the Hanford FTF was closed. From Fiscal Year (FY) 1992 to 1994, funding was not provided to the FTF Technical Support Group (TSG) at the Los Alamos National Laboratory. As a consequence, Round Robin Tests (RRTs), performed twice each year by the FTFs to assess constituency of test results among the FTFs, were not performed in FY 1992 and FY 1993. The Annual Reports of FTF test activities were not prepared for FY 1992 - 1995. Technical support provided to the FTFs was minimal. There is talk of closing a second FTF, and ongoing discussions as to whether DOE will continue to fund operation of the FTFs. In FY 1994, DOE Defense Programs commenced funding the TSG. RRT data for FY 1994 and 1995 have been entered into the database; the FY 1994 RRT report has been issued; and the FY 1995 RRT report is in progress. Data from semiannual reports have been retrieved and entered into the database. Standards related to HEPA filter test and procurement activities are now scheduled for issuance by FY 1996. Continuation of these activities depends on whether DOE will continue to support the HEPA filter test program. The history and activities of the FTFs and the TSG at Los Alamos have been reported at previous Air Cleaning Conferences. Data from the FY 1991 Annual Report of FTF activities was presented at the 1992 Air Cleaning Conference. Preparation of the Annual Reports was temporarily suspended in 1992. However, all of the FTF Semiannual report data have been retrieved and entered into the data base. This paper focuses primarily on the results of HEPA filter tests conducted by FTFs during FY 1992 - FY 1995, and the possible effects of the DOE program uncertainties on the quality of HEPA filters for installation at the DOE sites. 15 refs., 13 tabs.

  4. Performance Evaluation of Axial Flow AG-1 FC and Prototype FM (High Strength) HEPA Filters - 13123

    SciTech Connect

    Giffin, Paxton K.; Parsons, Michael S.; Wilson, John A.; Waggoner, Charles A.

    2013-07-01

    High efficiency particulate air (HEPA) filters are routinely used in DOE nuclear containment activities. The Nuclear Air Cleaning Handbook (NACH) stipulates that air cleaning devices and equipment used in DOE nuclear applications must meet the American Society of Mechanical Engineers (ASME) Code on Nuclear Air and Gas Treatment (AG-1) standard. This testing activity evaluates two different axial flow HEPA filters, those from AG-1 Sections FC and FM. Section FM is under development and has not yet been added to AG-1 due to a lack of qualification data available for these filters. Section FC filters are axial flow units that utilize a fibrous glass filtering medium. The section FM filters utilize a similar fibrous glass medium, but also have scrim backing. The scrim-backed filters have demonstrated the ability to endure pressure impulses capable of completely destroying FC filters. The testing activities presented herein will examine the total lifetime loading for both FC and FM filters under ambient conditions and at elevated conditions of temperature and relative humidity. Results will include loading curves, penetration curves, and testing condition parameters. These testing activities have been developed through collaborations with representatives from the National Nuclear Security Administration (NNSA), DOE Office of Environmental Management (DOE-EM), New Mexico State University, and Mississippi State University. (authors)

  5. Washing of waste prior to landfilling.

    PubMed

    Cossu, Raffaello; Lai, Tiziana

    2012-05-01

    The main impact produced by landfills is represented by the release of leachate emissions. Waste washing treatment has been investigated to evaluate its efficiency in reducing the waste leaching fraction prior to landfilling. The results of laboratory-scale washing tests applied to several significant residues from integrated management of solid waste are presented in this study, specifically: non-recyclable plastics from source separation, mechanical-biological treated municipal solid waste and a special waste, automotive shredded residues. Results obtained demonstrate that washing treatment contributes towards combating the environmental impacts of raw wastes. Accordingly, a leachate production model was applied, leading to the consideration that the concentrations of chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN), parameters of fundamental importance in the characterization of landfill leachate, from a landfill containing washed wastes, are comparable to those that would only be reached between 90 and 220years later in the presence of raw wastes. The findings obtained demonstrated that washing of waste may represent an effective means of reducing the leachable fraction resulting in a consequent decrease in landfill emissions. Further studies on pilot scale are needed to assess the potential for full-scale application of this treatment.

  6. Washing of waste prior to landfilling.

    PubMed

    Cossu, Raffaello; Lai, Tiziana

    2012-05-01

    The main impact produced by landfills is represented by the release of leachate emissions. Waste washing treatment has been investigated to evaluate its efficiency in reducing the waste leaching fraction prior to landfilling. The results of laboratory-scale washing tests applied to several significant residues from integrated management of solid waste are presented in this study, specifically: non-recyclable plastics from source separation, mechanical-biological treated municipal solid waste and a special waste, automotive shredded residues. Results obtained demonstrate that washing treatment contributes towards combating the environmental impacts of raw wastes. Accordingly, a leachate production model was applied, leading to the consideration that the concentrations of chemical oxygen demand (COD) and total Kjeldahl nitrogen (TKN), parameters of fundamental importance in the characterization of landfill leachate, from a landfill containing washed wastes, are comparable to those that would only be reached between 90 and 220years later in the presence of raw wastes. The findings obtained demonstrated that washing of waste may represent an effective means of reducing the leachable fraction resulting in a consequent decrease in landfill emissions. Further studies on pilot scale are needed to assess the potential for full-scale application of this treatment. PMID:22245736

  7. MicroRNA Responses to the Genotoxic Carcinogens Aflatoxin B1 and Benzo[a]pyrene in Human HepaRG Cells.

    PubMed

    Marrone, April K; Tryndyak, Volodymyr; Beland, Frederick A; Pogribny, Igor P

    2016-02-01

    Recent advances in toxicogenomics present an opportunity to develop new in vitro testing methodologies to identify human carcinogens. We have investigated microRNA expression responses to the treatment of human liver HepaRG cells with the human genotoxic carcinogens aflatoxin B1 (AFB1) and benzo[a]pyrene (B[a]P), and the structurally similar compounds aflatoxin B2 (AFB2) and benzo[e]pyrene (B[e]P) that exhibit minimal carcinogenic potential. We demonstrate that treatment of HepaRG cells with AFB1 or B[a]P resulted in specific changes in the expression of miRNAs as compared with their non-carcinogenic analogues, particularly in a marked over-expression of miR-410. An additional novel finding is the dose- and time-dependent inhibition of miR-122 in AFB1-treated HepaRG cells. Mechanistically, the AFB1-induced down-regulation of miR-122 was attributed to inhibition of the HNF4A/miR-122 regulatory pathway. These results demonstrate that HepaRG cells can be used to investigate miRNA responses to xenobiotic exposure, and illustrate the existence of early non-genotoxic events, in addition to a well-established genotoxic mode of action changes, in the mechanism of AFB1 and B[a]P carcinogenicity.

  8. Single treatment with ethanol hand rub is ineffective against human rhinovirus--hand washing with soap and water removes the virus efficiently.

    PubMed

    Savolainen-Kopra, Carita; Korpela, Terttu; Simonen-Tikka, Marja-Leena; Amiryousefi, Ali; Ziegler, Thedi; Roivainen, Merja; Hovi, Tapani

    2012-03-01

    Ethanol-containing hand rubs are used frequently as a substitute for hand washing with water and soap. However, not all viruses are inactivated by a short term rubbing with alcohol. The capacity of a single round of instructed and controlled hand cleaning with water and soap or ethanol-containing hand rub, respectively, was tested for removal of human rhinovirus administered onto the skin of healthy volunteers on the back of the hands. Hand washing with soap and water appeared to be much more efficient for removing rhinoviruses from skin than rubbing hands with an ethanol-containing disinfectant. After washing with soap and water the virus was detected in 3/9 (33.3%) test persons from the left hand and 1/9 (11.1%) cases from the right hand, whereas the virus was detected invariably by real-time RT-PCR from both hands after cleaning with alcohol hand rub (P-value <0.01). Both substances evaluated clinically were also tested in vitro for virucidal efficacy against Human rhinovirus2 (HRV2) using a standardized assay. Both tested substances were poor within the contact time used in the hand-cleaning test. In conclusion, thorough and conventional hand washing with water and soap can clean efficiently hands contaminated with the virus responsible for an extensive share of common cold episodes.

  9. Response of HEPA filters to simulated-accident conditions

    SciTech Connect

    Gregory, W.S.; Martin, R.A.; Smith, P.R.; Fenton, D.E.

    1982-01-01

    High-efficiency particulate air (HEPA) filters have been subjected to simulated accident conditions to determine their response to abnormal operating events. Both domestic and European standard and high-capacity filters have been evaluated to determine their response to simulated fire, explosion, and tornado conditions. The HEPA filter structural limitations for tornado and explosive loadings are discussed. In addition, filtration efficiencies during these accident conditions are reported for the first time. Our data indicate efficiencies between 80% and 90% for shock loadings below the structural limit level. We describe two types of testing for ineffective filtration - clean filters exposed to pulse-entrained aerosol and dirty filters exposed to tornado and shock pulses. Efficiency and material loss data are described. Also, the resonse of standard HEPA filters to simulated fire conditions is presented. We describe a unique method of measuring accumulated combustion products on the filter. Additionally, data relating to pressure drop vs accumulated mass during plugging are reported for simulated combustion aerosols. The effects of concentration and moisture levels on filter plugging were evaluated. We are obtaining all of the above data so that mathematical models can be developed for fire, explosion, and tornado accident analysis computer codes. These computer codes can be used to assess the response of nuclear air cleaning systems to accident conditions.

  10. Performance of HEPA filters under hot dynamic conditions

    SciTech Connect

    Frankum, D.P.; Costigan, G.

    1995-02-01

    Accidents in nuclear facilities involving fires may have implications upon the ventilation systems where high efficiency particulate air (HEPA) filters are used to minimise the airborne release of radioactive or toxic particles. The Filter Development Section at Harwell Laboratory has been investigating the effect of temperature on the performance of HEPA filters under hot dynamic conditions[{sub 1}] for a number of years. The test rig is capable of delivering air flows of 10001/s (at ambient conditions) at temperatures up to 500{degrees}C, where measurements of the penetration and pressure drop across the filter are obtained. This paper reports the experiments on different constructions of HEPA filters; rectangular and circular. The filters were tested at an air temperature of 200{degrees}C for up to 48 hours at the rated airflow to assess their performance. The penetration measurements for rectangular filters were observed to be below 0.021% after prolonged operation. In a number of cases, holes appeared along the pleat creases of circular filters although the penetration remained below 1%. The sealing gasket for these filters was noted to deform with temperature, permitting a leakage path. A prototype high strength circular filter was evaluated at temperatures of up to 400{degrees}C with a penetration less than 0.65%.

  11. Closure of 324 Facility potential HEPA filter failure unreviewed safety questions

    SciTech Connect

    Enghusen, M.B.

    1997-11-07

    This document summarizes the activities which occurred to resolve an Unreviewed Safety Question (USQ) for the 324 Facility [Waste Technology Engineering Laboratory] involving Potential HEPA Filter Breach. The facility ventilation system had the capacity to fail the HEPA filters during accident conditions which would totally plug the filters. The ventilation system fans were modified which lowered fan operating parameters and prevented HEPA filter failures which might occur during accident conditions.

  12. Washing Out the Competition

    NASA Technical Reports Server (NTRS)

    2001-01-01

    AJT Associates, Inc. (AJT) worked with NASA to develop a revolutionary ozone-based laundry system. AJT's TecH2Ozone(R) wash system presents its customers with an energy-efficient, cost-effective, and environmentally safe way to perform commercial laundering. TecH2Ozone significantly reduces the amount of water and chemical used as compared to traditional commercial laundry systems. This reduction has resulted in lower cost and shorter wash cycles. And due to the reduced use of chemicals, a significant portion of the rinse water is recycled back into the system for reuse. TecH2Ozone customers, such as hotels and other large commercial laundry facilities, have felt the benefits of this equipment. Because of the reduced cycle times, fewer washers are needed and there is a notable increase in the cleanliness of the laundry. The reduction in chemical residues is a boon to customers with allergies and those prone to skin irritation from chemicals retained in regular laundry. AJT Associates, Inc. (AJT) worked with NASA to develop a revolutionary ozone-based laundry system. AJT's TecH2Ozone(R) wash system presents its customers with an energy-efficient, cost-effective, and environmentally safe way to perform commercial laundering.

  13. PPAR agonists reduce steatosis in oleic acid-overloaded HepaRG cells

    SciTech Connect

    Rogue, Alexandra; Anthérieu, Sébastien; Vluggens, Aurore; Umbdenstock, Thierry; Claude, Nancy; Moureyre-Spire, Catherine de la; Weaver, Richard J.; Guillouzo, André

    2014-04-01

    Although non-alcoholic fatty liver disease (NAFLD) is currently the most common form of chronic liver disease there is no pharmacological agent approved for its treatment. Since peroxisome proliferator-activated receptors (PPARs) are closely associated with hepatic lipid metabolism, they seem to play important roles in NAFLD. However, the effects of PPAR agonists on steatosis that is a common pathology associated with NAFLD, remain largely controversial. In this study, the effects of various PPAR agonists, i.e. fenofibrate, bezafibrate, troglitazone, rosiglitazone, muraglitazar and tesaglitazar on oleic acid-induced steatotic HepaRG cells were investigated after a single 24-hour or 2-week repeat treatment. Lipid vesicles stained by Oil-Red O and triglycerides accumulation caused by oleic acid overload, were decreased, by up to 50%, while fatty acid oxidation was induced after 2-week co-treatment with PPAR agonists. The greatest effects on reduction of steatosis were obtained with the dual PPARα/γ agonist muraglitazar. Such improvement of steatosis was associated with up-regulation of genes related to fatty acid oxidation activity and down-regulation of many genes involved in lipogenesis. Moreover, modulation of expression of some nuclear receptor genes, such as FXR, LXRα and CAR, which are potent actors in the control of lipogenesis, was observed and might explain repression of de novo lipogenesis. Conclusion: Altogether, our in vitro data on steatotic HepaRG cells treated with PPAR agonists correlated well with clinical investigations, bringing a proof of concept that drug-induced reversal of steatosis in human can be evaluated in in vitro before conducting long-term and costly in vivo studies in animals and patients. - Highlights: • There is no pharmacological agent approved for the treatment of NAFLD. • This study demonstrates that PPAR agonists can reduce fatty acid-induced steatosis. • Some nuclear receptors appear to be potent actors in the control

  14. EPA site demonstration of the Biotrol Soil Washing Process

    SciTech Connect

    Stinson, M.K.; Skovronek, H.S.; Ellis, W.D.

    1992-01-01

    A pilot-scale soil washing process, patented by BioTrol, was demonstrated on soil that was contaminated by wood treating waste. The BioTrol Soil Washing was demonstrated in a treatment train sequence with two other pilot-scale units of BioTrol technologies for treatment of waste streams from the soil washer. The three technologies of the treatment train were: The BioTrol Soil Washer (BSW), the BioTrol Aqueous Treatment System (BATS), and the Slurry Bioreactor (SBR). The BioTrol processes were evaluated on pentachlorophenol (PCP) and polynuclear aromatic hydrocarbons (PAHs), which were the primary soil contaminants at the site. The sandy site soil, consisting of less than 10% of fines, was well suited for treatment by soil washing. The BSW successfully separated the feed soil (100% by weight) into 83% of washed soil, 10% of woody residues, and 7% of fines. The soil washer achieved up to 89% removal of PCP and PAHs, based on the difference between their levels in the feed soil and in the washed soil. The BATS degraded up to 94% of PCP in the process water from soil washing. The SBR achieved over 90% removals of PCP and 70-90% removals of PAHs, respectively from the soil washing. Cost of a commercial-scale soil washing, assuming use of all three technologies, was estimated to be $168 per ton of treated soil.

  15. DEMONSTRATION BULLETIN: SOIL WASHING SYSTEM - BIOTROL, INC.

    EPA Science Inventory

    The three component technologies of the BioTrol Soil Washing System (BSWS). Tested in the SITE demonstration were a Soil Washer (SW), and Aqueous Treatment System (ATS), and a Slurry Bio-Reactor (SBR). The Soil Washer operates on the principle that a significant fraction of the...

  16. Soil washing of fluorine contaminated soil using various washing solutions.

    PubMed

    Moon, Deok Hyun; Jo, Raehyun; Koutsospyros, Agamemnon; Cheong, Kyung Hoon; Park, Jeong-Hun

    2015-03-01

    Bench-scale soil washing experiments were conducted to remove fluoride from contaminated soils. Five washing solutions including hydrochloric acid (HCl), nitric acid (HNO3), sodium hydroxide (NaOH), sulfuric acid (H2SO4) and tartaric acid (C4H6O6) were tested. The concentration of the washing solutions used ranged from 0.1 to 3 M with a liquid to solid ratio of 10. The soil washing results showed that the most effective washing solution for the removal of fluoride from contaminated soils was HCl. The highest fluoride removal results of approximately 97 % from the contaminated soil were obtained using 3 M HCl. The fluoride removal efficiency of the washing solution increases in the following order: C4H6O6 < NaOH < H2SO4 < HNO3 < HCl.

  17. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING NORTHWEST. PIPING ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING NORTHWEST. PIPING IN FOREGROUND IS NOT RELATED TO THE MACHINE. THE NORTHEAST CORNER OF SETTLING RESERVOIR NO. 3 IS SEEN AT THE LOWER LEFT. - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  18. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING WEST. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING WEST. THE NONHISTORIC CHEMICAL BUILDING IS SEEN IN THE BACKGROUND. - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  19. Development and evaluation of a HEPA filter for increased strength and resistance to elevated temperature

    SciTech Connect

    Gilbert, H.; Bergman, W.; Fretthold, J.K.

    1992-12-31

    We have developed an improved HEPA filter for increased strength and resistance to elevated temperature to improve the reliability of HEPA filters under accident conditions. The improvements to the HEPA filter consist of a silicone rubber sealant and a new HEPA medium reinforced with a glass cloth. Several prototype filters were built and evaluated for temperature and pressure resistance and resistance to rough handling. The temperature resistance test consisted of exposing the HEPA filter to 1,000 scan at 700 degrees F for five minutes. The pressure resistance test consisted of exposing the HEPA filter to a differential pressure of 10 in. w.g. using a water saturated air flow at 95 degrees F. For the rough handling test, we used a vibrating machine designated the Q110. DOP filter efficiency tests were performed before and after each of the environmental tests. In addition to following the standard practice of using a separate new filter for each environmental test, we also subjected the same filter to the elevated temperature test followed by the pressure resistance test. The efficiency test results show that the improved HEPA filter is significantly better than the standard HEPA filter.

  20. Requirements for a cleanable steel HEPA filter derived from a systems analysis

    SciTech Connect

    Bergman, W.

    1996-06-01

    A systems analysis was conducted to determine customer requirements for a cleanable high efficiency particulate air (HEPA) filter in DOE Environmental Management (EM) facilities. The three principal drivers for cleanable steel HEPA are large cost savings, improved filter reliability, and new regulations; they produce a strong incentive to DOE customers to use cleanable steel HEPA filters. Input for customer requirements were obtained from field trips to EM sites and from discussions. Most existing applications require that cleanable steel HEPA filters meet size/performance requirements of standard glass HEPA filters; applications in new facilities can relax size/weight/pressure drop requirements on a case-by-case basis. We then obtained input from commercial firms on availability of cleanable steel HEPA filters. Systems analysis then showed that currently available technology was only able to meet customer needs in a limited number of cases. Further development is needed to meet requirements of EM customers. For cleanable steel HEPA to be retrofitted into existing systems, pressure drop and weight must be reduced. Pressure drop can be reduced by developing steel fiber media from 0.5 {mu}m dia steel fibers. Weight can be reduced by packaging the steel fiber media in one of the standard HEPA configurations. Although most applications will be able to use standard 304 or 316L alloys, an acid resistant alloy such as Hastelloy or Inconel will be needed for incinerator and other thermal processes.

  1. Method of treating contaminated HEPA filter media in pulp process

    DOEpatents

    Hu, Jian S.; Argyle, Mark D.; Demmer, Ricky L.; Mondok, Emilio P.

    2003-07-29

    A method for reducing contamination of HEPA filters with radioactive and/or hazardous materials is described. The method includes pre-processing of the filter for removing loose particles. Next, the filter medium is removed from the housing, and the housing is decontaminated. Finally, the filter medium is processed as pulp for removing contaminated particles by physical and/or chemical methods, including gravity, flotation, and dissolution of the particles. The decontaminated filter medium is then disposed of as non-RCRA waste; the particles are collected, stabilized, and disposed of according to well known methods of handling such materials; and the liquid medium in which the pulp was processed is recycled.

  2. Comparison of HEPA filter test methods in corrosive environments

    SciTech Connect

    Murphy, L.P.; Fernandez, S.J.; Motes, B.G.

    1980-07-01

    An evaluation of the three HEPA filter test methods in corrosive environments was conducted: the dioctyl phthalate (DOP) method (US Standard Method ANSI N-101.1-1972), the sodium chloride method (British Standard 3928:1969), and the soda-fluorescein or uranine method (French Standard AFNOR STD NFX 44-011). The effects of humidity, temperature and oxides of nitrogen (NO/sub x/) on each method was examined. The experimental design used in the evaluation measured and separated both the effect of each variable and any interaction between variables on the test method. Recommendations for changes in the standard methods to reduce erratic online results are presented.

  3. Improved HEPA Filter Technology for Flexible and Rigid Containment Barriers

    SciTech Connect

    Pinson, Paul Arthur

    1998-07-01

    Safety and reliability in glovebox operations can be significantly improved and waste packaging efficiencies can be increased by inserting flexible, lightweight, high capacity HEPA filters into the walls of plastic sheet barriers. This HEPA filter/barrier technology can be adapted to a wide variety of applications: disposable waste bags, protective environmental barriers for electronic equipment, single or multiple use glovebag assemblies, flexible glovebox wall elements, and room partitions. These reliable and inexpensive filtered barriers have many uses in fields such as radioactive waste processing, HVAC filter changeout, vapor or grit blasting, asbestos cleanup, pharmaceutical, medical, biological, and electronic equipment containment. The applications can result in significant cost savings, improved operational reliability and safety, and total waste volume reduction. This technology was developed at the Argonne National Laboratory-West (ANL-W) in 1993 and has been used at ANL-W since then at the TRU Waste Characterization Chamber Gloveboxes. Another 1998 AGS Conference paper titled "TRU Waste Characterization Gloveboxes", presented by Mr. David Duncan of ANL-W, describes these boxes.

  4. Comparison of HEPA filter test methods in corrosive environments

    SciTech Connect

    Murphy, L.P.; Fernandez, S.J.; Motes, B.G.

    1980-01-01

    The in-plant testing of process off-gas high efficiency particular air (HEPA) filters is an important quality control activity of the ALARA (As Low As Reasonably Achievable) policy at nuclear facilities. Imprecise and irreproducible data were recorded during DOP testing at the Atmospheric Protection System (APS) of the Idaho Chemical Processing Plant (ICPP). The tests at the APS are performed in an environment that has high humidity, high temperatures and has NO/sub x/ present. An evaluation of three HEPA filter test methods in corrosive environments was conducted: the dioctyl phthalate (DOP) method (US Standard Method ANSI N-101.1-1979) the sodium chloride method (British Standard 3928:1969), and the soda-fluorescein or uranine method (French Standard AFNOR STD NFX 44-011). The effects of high humidity, temperature, and oxides of nitrogen (NO/sub x/) on each method was examined. The effects of each variable and any interaction between variables on the test methods were examined. Recommendations for changes in the standard methods to reduce erratic on-line results are presented.

  5. Preliminary studies to determine the shelf life of HEPA filters

    SciTech Connect

    Gilbert, H.; Fretthold, J.K.; Rainer, F.; Bergman, W.; Beason, D.

    1994-07-18

    We have completed a preliminary study using filter media tests and filter qualification tests to investigate the effect of shelf-life on HEPA filter performance. Our media studies showed that the tensile strength decreased with age, but the data were not sufficient to establish a shelf-life. Thermogravimetric analyses demonstrated that one manufacturer had media with low tensile strength due to insufficient binder. The filter qualification tests (heated air and overpressure) conducted on different aged filters showed that filter age is not the primary factor affecting filter performance; materials and the construction design have a greater effect. An unexpected finding of our study was that sub-standard HEPA filters have been installed in DOE facilities despite existing regulations and filter qualification tests. We found that the filter with low tensile strength failed the overpressure test. The same filter had passed the heated air test, but left the filter so structurally weak, it was prone to blowout. We recommend that DOE initiate a filter qualification program to prevent this occurrence.

  6. Preliminary studies to determine the shelf life of HEPA filters

    SciTech Connect

    Gilbert, H.; Fretthold, J.K.; Rainer, F.

    1995-02-01

    We have completed a preliminary study using filter media tests and filter qualification tests to investigate the effect of shelf-life on HEPA filter performance. Our media studies showed that the tensile strength decreased with age, but the data were not sufficient to establish a shelf-life. Thermogravimetric analyses demonstrated that one manufacturer had media with low tensile strength due to insufficient binder. The filter qualification tests (heated air and overpressure) conducted on different aged filters showed that filter age is not the primary factor affecting filter performance; materials and the construction design have a greater effect. An unexpected finding of our study was that sub-standard HEPA filters have been installed in DOE facilities despite existing regulations and filter qualification tests. We found that the filter with low tensile strength failed the overpressure test. The same filter had passed the heated air test, but left the filter so structurally weak, it was prone to blow-out. We recommend that DOE initiate a filter qualification program to prevent this occurrence.

  7. Transcriptomic analysis of untreated and drug-treated differentiated HepaRG cells over a 2-week period.

    PubMed

    Savary, Camille C; Jiang, Xiaoqi; Aubry, Marc; Jossé, Rozenn; Kopp-Schneider, Annette; Hewitt, Philip; Guillouzo, André

    2015-12-25

    Previous works have shown that differentiated human HepaRG cells can exhibit drug metabolism activities close to those of primary human hepatocytes for several weeks at confluence. The present study was designed to evaluate their long-term functional stability and their response to repeated daily drug treatments over a 14-day period, using a transcriptomic approach. Our data show that less than 1% of the expressed genes were markedly deregulated over this two weeks period and mainly included down-regulation of genes related to the cell cycle and from 3 days, overexpression of genes involved in xenobiotic and lipid metabolism. After daily treatment with the three PPAR agonists, fenofibrate, troglitazone and rosiglitazone qualitative and/or quantitative changes in gene profiling were observed depending on the compound and duration of treatment. The highest increase in the number of deregulated genes as a function of drug treatment was seen with rosiglitazone. The most up-regulated genes common across the three compounds were mainly related to lipid and xenobiotic metabolisms. All the data support the conclusion that human HepaRG cells have an exceptional functional stability at confluence and that they are suitable for investigations on chronic effects of drugs and other chemicals.

  8. Potential for Hepa filter damage from water spray systems in filter plenums

    SciTech Connect

    Bergman, W.; Fretthold, J.K.; Slawsld, J.W.

    1997-01-01

    The water spray systems in high efficiency particulate air (HEPA) filter plenums that are used in nearly all Department of Energy (DOE) facilities for protection against fire was designed under the assumption that the HEPA filters would not be damaged by the water sprays. The most likely scenario for filter damage involves filter plugging by the water spray, followed by the fan blowing out the filter medium. A number of controlled laboratory tests that were previously conducted in the late 1980s are reviewed in this paper to provide a technical basis for the potential HEPA filter damage by the water spray system in HEPA filter plenums. In addition to the laboratory tests, the scenario for HEPA filter damage during fires has also occurred in the field. Afire in a four-stage, HEPA filter plenum at Rocky Flats in 1980 caused the first three stages of HEPA filters to blow out of their housing and the fourth stage to severely bow. Details of this recently declassified fire are presented in this paper. Although these previous findings suggest serious potential problems exist with the current water spray system in filter plenum , additional studies are required to confirm unequivocally that DOE`s critical facilities are at risk.

  9. Washing of the AW-101 entrained solids

    SciTech Connect

    GJ Lumetta

    2000-03-31

    BNFL Inc. (BNFL) is under contract with the US Department of Energy, River Protection Project (DOE-RPP) to design, construct, and operate facilities for treating wastes stored in the single-shell and double-shell tanks at the Hanford Site, Richland, Washington. The DOE-BNFL RPP contract identifies two feeds to the waste treatment plant: (1) primarily liquid low-activity waste (LAW) consisting of less than 2 wt% entrained solids and (2) high-level waste (HLW) consisting of 10 to 200 g/L solids slurry. This report describes the results of a test conducted by Battelle to assess the effects of inhibited water washing on the composition of the entrained solids in the diluted AW-101 low-activity waste (LAW) sample. The objective of this work was to gather data on the solubility of the AW-101 entrained solids in 0.01 M NaOH, so that BNFL can evaluate whether these solids require caustic leaching. The work was conducted according to test plan BNFL-TP-29953-9, Rev. 0, LAW Entrained Solids Water Wash and Caustic Leach Testing. The test went according to plan, with no deviations from the test plan. Based on the results of the 0.01 M NaOH washing, a decision was made by BNFL to not proceed with the caustic leaching test. The composition of the washed solids was such that caustic leaching would not result in significant reduction in the immobilized HLW volume.

  10. Sludge pretreatment chemistry evaluation: Enhanced sludge washing separation factors

    SciTech Connect

    Colton, N.G.

    1995-03-01

    This report presents the work conducted in Fiscal Year 1994 by the Sludge Pretreatment Chemistry Evaluation Subtask for the Tank Waste Remediation System (TWRS) Tank Waste Treatment Science Task. The main purpose of this task, is to provide the technical basis and scientific understanding to support TWRS baseline decisions and actions, such as the development of an enhanced sludge washing process to reduce the volume of waste that will require high-level waste (HLW) vitrification. One objective within the Sludge Pretreatment Chemistry Evaluation Subtask was to establish wash factors for various SST (single-shell tank) sludges. First, analytical data were compiled from existing tank waste characterization reports. These data were summarized on tank-specific worksheets that provided a uniform format for reviewing and comparing data, as well as the means to verify whether the data set for each tank was complete. Worksheets were completed for 27 SST wastes. The analytical water wash data provided tank-specific information about the fraction of each component that dissolves with water, i.e., an estimate of tank-specific wash factors for evaluating tank-by-tank processing. These wash data were then used collectively to evaluate some of the wash factors that are assumed for the overall SST waste inventory; specifically, wash factors for elements that would be found primarily in sludges. The final step in this study was to incorporate the characterization and wash factor data into a spreadsheet that provides insight into the effect of enhanced sludge washing on individual tank sludges as well as for groups of sludges that may be representative of different waste types. Spreadsheet results include the estimated mass and percentage of each element that would be removed with washing and leaching. Furthermore, estimated compositions are given of the final wash and leach streams and residual solids, in terms of both concentration and dry weight percent.

  11. Dose- and time-dependent effects of phenobarbital on gene expression profiling in human hepatoma HepaRG cells

    SciTech Connect

    Lambert, Carine B.; Spire, Catherine Claude, Nancy; Guillouzo, Andre

    2009-02-01

    Phenobarbital (PB) induces or represses a wide spectrum of genes in rodent liver. Much less is known about its effects in human liver. We used pangenomic cDNA microarrays to analyze concentration- and time-dependent gene expression profile changes induced by PB in the well-differentiated human HepaRG cell line. Changes in gene expression profiles clustered at specific concentration ranges and treatment times. The number of correctly annotated genes significantly modulated by at least three different PB concentration ranges (spanning 0.5 to 3.2 mM) at 20 h exposure amounted to 77 and 128 genes (p {<=} 0.01) at 2- and 1.8-fold filter changes, respectively. At low concentrations (0.5 and 1 mM), PB-responsive genes included the well-recognized CAR- and PXR-dependent responsive cytochromes P450 (CYP2B6, CYP3A4), sulfotransferase 2A1 and plasma transporters (ABCB1, ABCC2), as well as a number of genes critically involved in various metabolic pathways, including lipid (CYP4A11, CYP4F3), vitamin D (CYP24A1) and bile (CYP7A1 and CYP8B1) metabolism. At concentrations of 3.2 mM or higher after 20 h, and especially 48 h, increased cytotoxic effects were associated with disregulation of numerous genes related to oxidative stress, DNA repair and apoptosis. Primary human hepatocyte cultures were also exposed to 1 and 3.2 mM PB for 20 h and the changes were comparable to those found in HepaRG cells treated under the same conditions. Taken altogether, our data provide further evidence that HepaRG cells closely resemble primary human hepatocytes and provide new information on the effects of PB in human liver. These data also emphasize the importance of investigating dose- and time-dependent effects of chemicals when using toxicogenomic approaches.

  12. Results from Evaluation of Representative ASME AG-1 Section FK Radial Flow Dimple Pleated HEPA Filters Under Elevated Conditions - 12002

    SciTech Connect

    Giffin, Paxton K.; Parsons, Michael S.; Rickert, Jaime G.; Waggoner, Charles A.

    2012-07-01

    The American Society of Mechanical Engineers (ASME) has recently added Section FK establishing requirements for radial flow HEPA filters to the Code on Nuclear Air and Gas Treatment (AG-1). Section FK filters are expected to be a major element in the HEPA filtration systems across the US Department of Energy (DOE) complex. Radial flow filters have been used in Europe for some time, however a limited amount of performance evaluation data exists with respect to these new AG-1 Section FK units. In consultation with a technical working group, the Institute for Clean Energy Technology (ICET) at Mississippi State University (MSU)has evaluated a series of representative AG-1 Section FK dimple pleated radial flow HEPA filters. The effects of elevated relative humidity and temperature conditions on these filters are particularly concerning. Results from the evaluation of Section FK filters under ambient conditions have been presented at the 2011 waste management conference. Additions to the previous test stand to enable high temperature and high humidity testing, a review of the equipment used, the steps taken to characterize the new additions, and the filter test results are presented in this study. Test filters were evaluated at a volumetric flow rate of 56.6 m{sup 3}/min (2000 cfm) and were challenged under ambient conditions with Alumina, Al(OH){sub 3}, until reaching a differential pressure of 1 kPa (4 in. w.c.), at which time the filters were tested, unchallenged with aerosol, at 54 deg. C (130 deg. F) for approximately 1 hour. At the end of that hour water was sprayed near the heat source to maximize vaporization exposing the filter to an elevated relative humidity up to 95%. Collected data include differential pressure, temperature, relative humidity, and volumetric flow rate versus time. (authors)

  13. The synthetic retinoid AGN 193109 but not retinoic acid elevates CYP1A1 levels in mouse embryos and Hepa-1c1c7 cells.

    PubMed

    Soprano, D R; Gambone, C J; Sheikh, S N; Gabriel, J L; Chandraratna, R A; Soprano, K J; Kochhar, D M

    2001-07-15

    The synthetic retinoid AGN 193109 is a potent pan retinoic acid receptor (RAR) antagonist. Treatment of pregnant mice with a single oral 1 mg/kg dose of this antagonist on day 8 postcoitum results in severe craniofacial (median cleft face or frontonasal deficiency) and eye malformations in virtually all exposed fetuses. Using differential display analysis, we have determined that CYP1A1 mRNA levels are elevated in mouse embryos 6 h following treatment with AGN 193109. Similarly, an elevation in CYP1A1 mRNA levels, protein levels, and aryl hydrocarbon hydoxylase activity occurs in Hepa-1c1c7 cells, with the maximal elevation observed when the cells were treated with 10(-5) M AGN 193109 for 4 to 8 h. Elevation in CYP1A1 mRNA levels in mouse embryos and Hepa-1c1c7 cells does not occur upon treatment with the natural retinoid, all-trans-retinoic acid. Finally, elevation in CYP1A1 mRNA levels was not observed when mutant Hepa-1c1c7 cells, which are defective in either the aryl hydrocarbon receptor (AhR) or aryl hydrocarbon receptor nuclear translocator (ARNT), were treated with AGN 193109. This suggests that the AhR/ARNT pathway and not the RAR/RXR pathway is mediating the elevation of CYP1A1 mRNA levels by AGN 193109, at least in the Hepa-1c1c7 cells. This is the first example of a retinoid that displays the abililty to regulate both the RAR/RXR and AhR/ARNT transcriptional regulatory pathways.

  14. Method for HEPA filter leak scanning with differentiating aerosol detector

    SciTech Connect

    Kovach, B.J.; Banks, E.M.; Wikoff, W.O.

    1997-08-01

    While scanning HEPA filters for leaks with {open_quotes}Off the Shelf{close_quote} aerosol detection equipment, the operator`s scanning speed is limited by the time constant and threshold sensitivity of the detector. This is based on detection of the aerosol density, where the maximum signal is achieved when the scanning probe resides over the pinhole longer than several detector time-constants. Since the differential value of the changing signal can be determined by observing only the first small fraction of the rising signal, using a differentiating amplifier will speed up the locating process. The other advantage of differentiation is that slow signal drift or zero offset will not interfere with the process of locating the leak, since they are not detected. A scanning hand-probe attachable to any NUCON{reg_sign} Aerosol Detector displaying the combination of both aerosol density and differentiated signal was designed. 3 refs., 1 fig.

  15. Teens and Acne Treatment

    MedlinePlus

    ... Types of treatments Benzoyl peroxide Benzoyl peroxide wash, lotion, or gel—the most effective acne treatment you ... and make it redder than the wash or lotion, so try the wash or lotion first. How ...

  16. Scoping decision document for HEPA filter differential pressure interlock control installation and tank farm exhauster operation

    SciTech Connect

    GUSTAVSON, R.D.

    2001-06-27

    This document is a decision document regarding the scope of HEPA filter differential pressure interlock system installations at Tank Farm emission units. It is intended to provide supporting information for administration of Baseline Change Request.

  17. Criteria for calculating the efficiency of HEPA filters during and after design basis accidents

    SciTech Connect

    Bergman, W.; First, M.W.; Anderson, W.L.; Gilbert, H.; Jacox, J.W.

    1994-12-01

    We have reviewed the literature on the performance of high efficiency particulate air (HEPA) filters under normal and abnormal conditions to establish criteria for calculating the efficiency of HEPA filters in a DOE nonreactor nuclear facility during and after a Design Basis Accident (DBA). The literature review included the performance of new filters and parameters that may cause deterioration in the filter performance such as filter age, radiation, corrosive chemicals, seismic and rough handling, high temperature, moisture, particle clogging, high air flow and pressure pulses. The deterioration of the filter efficiency depends on the exposure parameters; in severe exposure conditions the filter will be structurally damaged and have a residual efficiency of 0%. Despite the many studies on HEPA filter performance under adverse conditions, there are large gaps and limitations in the data that introduce significant error in the estimates of HEPA filter efficiencies under DBA conditions. Because of this limitation, conservative values of filter efficiency were chosen when there was insufficient data.

  18. Safety evaluation for packaging (onsite) for the Pacific Northwest National Laboratory HEPA filter box

    SciTech Connect

    McCoy, J.C.

    1998-07-15

    This safety evaluation for packaging (SEP) evaluates and documents the safe onsite transport of eight high-efficiency particulate air (HEPA) filters in the Pacific Northwest National Laboratory HEPA Filter Box from the 300 Area of the Hanford Site to the Central Waste Complex and on to burial in the 200 West Area. Use of this SEP is authorized for 1 year from the date of release.

  19. Results from nondestructive assay measurement of the 296-P-34 Rotary mode core sampler HEPA filters

    SciTech Connect

    HOMAN, N.A.

    1999-06-04

    The objective of this data acquisition was to measure and identify the gamma emissions from the 296-P-34 exhauster high-efficiency particulate air (HEPA) filters. Data acquisition was accomplished by nondestructive assay (NDA), using a portable gamma spectrometer calibrated to the exhauster HEPA filter geometry. The NDA technique that was used is referenced in 40 CFR 61 Appendix B Method 114 and also addressed in HNF-EP-0528.

  20. Evaluation of glass fiber Hepa filters as a function of media velocity

    SciTech Connect

    Alderman, S.L.; Parsons, M.S.; Hogancamp, K.U.; Waggoner, C.A.

    2007-07-01

    Section FC of the ASME AG-1 Code addresses glass fiber HEPA filters and restricts the media velocity to a maximum of 5 ft./min. Advances in filter media technology allow glass fiber HEPA filters to function at significantly higher velocities and still achieve HEPA performance. Ultrafine particles (< 100 nm) are removed by a diffusive capture mechanism. The removal efficiency of these particles is reduced at higher media velocities due to shorter residence times within the media matrix. Therefore, it is unlikely that higher media velocities for HEPA filters will be allowed without data to demonstrate the effect of media velocity on removal of particles in the smaller size classes. Additional questions remain regarding particle loading and filter lifetimes at higher media velocities. In order to address these issues, nuclear grade AG-1 HEPA filters obtained from two manufacturers have been evaluated at media velocities ranging from 4 to 8.8 ft./min. KCl was utilized as aerosol challenge material and data regarding filter lifetimes, loading characteristics, changes in filtering efficiency and the most penetrating particle size are presented. Results of this testing will be provided to the ASME AG-1 FC Committee for consideration in future versions of the HEPA standard and will be useful for the development of air filtration systems in a nuclear environment. (authors)

  1. Fostering hand washing before lunch by students attending a special needs young adult program.

    PubMed

    Walmsley, Christopher; Mahoney, Amanda; Durgin, Amy; Poling, Alan

    2013-01-01

    A multiple baseline across groups design was used to investigate the effects of a treatment package on hand washing before lunch by five students with disabilities who attended a young adult educational program. To evaluate hand washing, a lotion called Glo Germ was applied to participants' hands. Glo Germ is visible under a black light, which allowed the quality of hand washing to be assessed by comparing the amount visible before and after hand washing using a 3-point scale. Following a baseline period in which hand washing was assessed, participants were exposed to a hand washing training procedure, which improved one participant's hand washing. Next, a lottery system was imposed in which the number of lottery tickets earned each day depended on the quality of hand washing, specifically, on the rating assigned (0, 1, or 2). This condition was associated with improved hand washing by the other four participants. Finally, a condition adding feedback to the lottery system resulted in further improvements in the quality of hand washing for all participants. Follow up data indicated modest maintenance of hand washing after lunch. These results suggest that treatment packages similar to that used in the present study merit further investigation and that Glo Germ is of value in ascertaining the quality of hand washing. PMID:22940163

  2. Fostering hand washing before lunch by students attending a special needs young adult program.

    PubMed

    Walmsley, Christopher; Mahoney, Amanda; Durgin, Amy; Poling, Alan

    2013-01-01

    A multiple baseline across groups design was used to investigate the effects of a treatment package on hand washing before lunch by five students with disabilities who attended a young adult educational program. To evaluate hand washing, a lotion called Glo Germ was applied to participants' hands. Glo Germ is visible under a black light, which allowed the quality of hand washing to be assessed by comparing the amount visible before and after hand washing using a 3-point scale. Following a baseline period in which hand washing was assessed, participants were exposed to a hand washing training procedure, which improved one participant's hand washing. Next, a lottery system was imposed in which the number of lottery tickets earned each day depended on the quality of hand washing, specifically, on the rating assigned (0, 1, or 2). This condition was associated with improved hand washing by the other four participants. Finally, a condition adding feedback to the lottery system resulted in further improvements in the quality of hand washing for all participants. Follow up data indicated modest maintenance of hand washing after lunch. These results suggest that treatment packages similar to that used in the present study merit further investigation and that Glo Germ is of value in ascertaining the quality of hand washing.

  3. Mold colonization during use of preservative-treated and untreated air filters, including HEPA filters from hospitals and commercial locations over an 8-year period (1996-2003).

    PubMed

    Price, Daniel L; Simmons, Robert B; Crow, Sidney A; Ahearn, Donald G

    2005-07-01

    High efficiency particulate arrestance (HEPA; 99.97% efficient at 0.3 microm) filters, filters with ASHRAE particulate arrestance rating of 90-95% at 1 mum (90-95% filters), and lower efficiency cellulosic-polyester filters from air conditioning systems in hospitals and commercial buildings were removed from the systems and examined microscopically for mold colonization. Cellulosic-type filters from systems with water entrainment problems typically were colonized, or became colonized upon incubation in moisture chambers. Species of Acremonium, Aspergillus, and Cladosporium were most common. With air filters of all types, treatment of filter media with an antimicrobial preservative tended to reduce or delay colonization. Mold colonization of HEPA and 90-95% filters was observed most often on the load surfaces, but two untreated HEPA filters were permeated with fungi, one with Aspergillus flavus, the other with Cladosporium sp. Air filters in heating, ventilating, and air conditioning (HVAC) systems, particularly those with chronic or periodic exposure to moisture, may serve as point sources for indoor molds. PMID:15856351

  4. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTH. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTH. THE OUTSIDE FACE OF THE NORTH WALL OF SETTLING RESERVOIR NO. 3 IS SEEN AT THE RIGHT. THE SETTLING RESERVOIR IS ELEVATED ABOVE THE FILTERING RESERVOIR TO ACHIEVE GRAVITY WATER FLOW FROM THE SETTLING RESERVOIR INTO THE FILTERING RESERVOIR. - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  5. Development of the sampling and nuclide analysis methods for spent HEPA filter wastes

    SciTech Connect

    Young-Yong Ji; Dae Seok Hong; Il-Sik Kang; Bum-Kyoung Seo; Jong-Sik Shon

    2007-07-01

    Spent filter wastes of about 2,160 units have been stored in the waste storage facility of the Korea Atomic Energy Research Institute since its operation. These spent filters have generally consisted of a HEPA filter after its filtering of all the contaminants in the gas stream generated during the operation of the HANARO research reactor and the nuclear fuel cycle facilities. At the moment, to secure enough storage space, it is necessary to make a volume reduction of the stored radioactive wastes through a compression treatment or a regulatory clearance. There have been many studies on a treatment and a clearance of the low level radioactive wastes generated from nuclear facilities. These methods are used in view of a reduction of a management cost and disposal cost and the security of free space for a waste storage facility approaching saturation. In order to dispose of the spent filters, it is first necessary to conduct a radionuclide assessment of them. To do that, a sampling procedure should be prepared to obtain a representative sample from a spent filter. As for conducting a nuclide analysis for this representative sample, a corresponding spent filter can be determined as either a regulatory clearance waste or a radioactive waste. (authors)

  6. 27 CFR 19.310 - Wash water.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2012-04-01 2012-04-01 false Wash water. 19.310 Section 19.310 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Byproducts § 19.310 Wash water. Water used in washing chemicals to remove spirits may be run into a wash...

  7. 27 CFR 19.310 - Wash water.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2013-04-01 2013-04-01 false Wash water. 19.310 Section 19.310 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Byproducts § 19.310 Wash water. Water used in washing chemicals to remove spirits may be run into a wash...

  8. 27 CFR 19.310 - Wash water.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2014-04-01 2014-04-01 false Wash water. 19.310 Section 19.310 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Byproducts § 19.310 Wash water. Water used in washing chemicals to remove spirits may be run into a wash...

  9. 27 CFR 19.328 - Wash water.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Wash water. 19.328 Section... THE TREASURY LIQUORS DISTILLED SPIRITS PLANTS Production Chemical By-Products § 19.328 Wash water. Water used in washing chemicals to remove spirits therefrom may be run into a wash tank or a...

  10. 27 CFR 19.310 - Wash water.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2011-04-01 2011-04-01 false Wash water. 19.310 Section 19.310 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF... Byproducts § 19.310 Wash water. Water used in washing chemicals to remove spirits may be run into a wash...

  11. Development and evaluation of a HEPA filter for increased strength and resistance to elevated temperature. Revision 1

    SciTech Connect

    Gilbert, H.; Bergman, W.; Fretthold, J.K.

    1993-01-01

    We have completed a preliminary study of an improved HEPA filter for increased strength and resistance to elevated temperature to improve the reliability of the standard deep pleated HEPA filter under accident conditions. The improvements to the HEPA filter consist of a silicone rubber sealant and a new HEPA medium reinforced with a glass cloth. Three prototype filters were built and evaluated for temperature and pressure resistance and resistance to rough handling. The temperature resistance test consisted of exposing the HEPA filter to 1,000 scan (1,700 m{sup 3}/hr) at 700{degrees}F (371{degrees}C) for five minutes.The pressure resistance test consisted of exposing the HEPA filter to a differential pressure of 10 in. w.g. (2.5 kPa) using a water saturated air flow at 95{degrees}F (35{degrees}C). For the rough handling test, we used a vibrating machine designated the Q110. DOP filter efficiency tests were performed before and after each of the environmental tests. In addition to following the standard practice of using a separate new filter for each environmental test, we also subjected the same filter to the elevated temperature test followed by the pressure resistance test. The efficiency test results show that the improved HEPA filter is significantly better than the standard HEPA filter. Further studies are recommended to evaluate the improved HEPA filter and to assess its performance under more severe accident conditions.

  12. In vivo – in vitro toxicogenomic comparison of TCDD-elicited gene expression in Hepa1c1c7 mouse hepatoma cells and C57BL/6 hepatic tissue

    PubMed Central

    Dere, Edward; Boverhof, Darrell R; Burgoon, Lyle D; Zacharewski, Timothy R

    2006-01-01

    Background In vitro systems have inherent limitations in their ability to model whole organism gene responses, which must be identified and appropriately considered when developing predictive biomarkers of in vivo toxicity. Systematic comparison of in vitro and in vivo temporal gene expression profiles were conducted to assess the ability of Hepa1c1c7 mouse hepatoma cells to model hepatic responses in C57BL/6 mice following treatment with 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD). Results Gene expression analysis and functional gene annotation indicate that Hepa1c1c7 cells appropriately modeled the induction of xenobiotic metabolism genes in vivo. However, responses associated with cell cycle progression and proliferation were unique to Hepa1c1c7 cells, consistent with the cell cycle arrest effects of TCDD on rapidly dividing cells. In contrast, lipid metabolism and immune responses, representative of whole organism effects in vivo, were not replicated in Hepa1c1c7 cells. Conclusion These results identified inherent differences in TCDD-mediated gene expression responses between these models and highlighted the limitations of in vitro systems in modeling whole organism responses, and additionally identified potential predictive biomarkers of toxicity. PMID:16611356

  13. Cost and waste volume reduction in HEPA filter trains by effective pre-filtration

    SciTech Connect

    Chadwick, Chris

    2007-07-01

    Data published elsewhere (Moore, et al., 1992; Bergman et al., 1997) suggests that the then costs of disposable type Glass Fibre HEPA filtration trains to the DOE was $55 million per year (based on an average usage of HEPA panels of 11,748 pieces per year between 1987 and 1990), $50 million of which was attributable to installation, testing, removal and disposal. The same authors suggest that by 1995 the number of HEPA panels being used had dropped to an estimated 4000 pieces per year due to the ending of the Cold War. The yearly cost to the DOE of 4000 units per year was estimated to be $29.5 million using the same parameters that previously suggested the $55 million figure. Within that cost estimate, $300 each was the value given to the filter and $4,450 was given to peripheral activity per filter. Clearly, if the $4,450 component could be reduced, tremendous saving could result, in addition to a significant reduction in the legacy burden of waste volumes. This same cost is applied to both the 11,748 and 4000 usage figures. The work up to now has focussed on the development of a low cost, long life (cleanable), direct replacement of the traditional filter train. This paper will review an alternative strategy, that of preventing the contaminating dust from reaching and blinding the HEPA filters, and thereby removing the need to replace them. What has become clear is that 'low cost' and 'Metallic HEPA' are not compatible terms. The original Bergman et al., 1997 work suggested that 1000 cfm (cubic feet per minute) (1690 m{sup 3}/hr) stainless HEPAs could be commercially available for $5000 each after development (although the $70,000 development unit may be somewhat exaggerated - the authors own company have estimated development units able to be retrofitted into strengthened standard housings would be available for perhaps $30,000). The likely true cost of such an item produced industrially in significant numbers may be closer to $15,000 each. That being the case

  14. A Window-Washing Challenge

    ERIC Educational Resources Information Center

    Roman, Harry T.

    2010-01-01

    Skyscrapers sure do have a lot of windows, and these windows are cleaned and checked regularly. All this takes time, money, and puts workers at potential risk. Might there be a better way to do it? In this article, the author discusses a window-washing challenge and describes how students can tackle this task, pick up the challenge, and creatively…

  15. Filter Paper: Solution to High Self-Attenuation Corrections in HEPA Filter Measurements

    SciTech Connect

    Oberer, R.B.; Harold, N.B.; Gunn, C.A.; Brummett, M.; Chaing, L.G.

    2005-10-01

    An 8 by 8 by 6 inch High Efficiency Particulate Air (HEPA) filter was measured as part of a uranium holdup survey in June of 2005 as it has been routinely measured every two months since 1998. Although the survey relies on gross gamma count measurements, this was one of a few measurements that had been converted to a quantitative measurement in 1998. The measurement was analyzed using the traditional Generalized Geometry Holdup (GGH) approach, using HMS3 software, with an area calibration and self-attenuation corrected with an empirical correction factor of 1.06. A result of 172 grams of {sup 235}U was reported. The actual quantity of {sup 235}U in the filter was approximately 1700g. Because of this unusually large discrepancy, the measurement of HEPA filters will be discussed. Various techniques for measuring HEPA filters will be described using the measurement of a 24 by 24 by 12 inch HEPA filter as an example. A new method to correct for self attenuation will be proposed for this measurement Following the discussion of the 24 by 24 by 12 inch HEPA filter, the measurement of the 8 by 8 by 6 inch will be discussed in detail.

  16. A basket for washing benthological samples

    USGS Publications Warehouse

    Selgeby, James H.

    1971-01-01

    Since benthological samples collected with dredges are usually too large to be preserved in toto, a washing method must be employed to reduce the sample volume without losing or damaging the organisms. Traditionally, the sample is washed in a sieve until the volume is small enough for convenient handling or preservation. Most washing procedures are time-consuming and laborious. To save time in washing samples, a washing 'basket' was designed which accomadates a Ponar dredge. The only additional equipment needed to employ the washing basket effectively is a pump that delivers about 8 gallons of water per minute.

  17. Effect of different soil washing solutions on bioavailability of residual arsenic in soils and soil properties.

    PubMed

    Im, Jinwoo; Yang, Kyung; Jho, Eun Hea; Nam, Kyoungphile

    2015-11-01

    The effect of soil washing used for arsenic (As)-contaminated soil remediation on soil properties and bioavailability of residual As in soil is receiving increasing attention due to increasing interest in conserving soil qualities after remediation. This study investigates the effect of different washing solutions on bioavailability of residual As in soils and soil properties after soil washing. Regardless of washing solutions, the sequential extraction revealed that the residual As concentrations and the amount of readily labile As in soils were reduced after soil washing. However, the bioassay tests showed that the washed soils exhibited ecotoxicological effects - lower seed germination, shoot growth, and enzyme activities - and this could largely be attributed to the acidic pH and/or excessive nutrient contents of the washed soils depending on washing solutions. Overall, this study showed that treated soils having lower levels of contaminants could still exhibit toxic effects due to changes in soil properties, which highly depended on washing solutions. This study also emphasizes that data on the As concentrations, the soil properties, and the ecotoxicological effects are necessary to properly manage the washed soils for reuses. The results of this study can, thus, be utilized to select proper post-treatment techniques for the washed soils. PMID:26086811

  18. HEPA Filter Differential Pressure Fan Interlock System Functional Requirements and Technical Design Criteria

    SciTech Connect

    TUCK, J.A.

    2000-05-11

    Double-shell tanks (DSTs) and Double Contained Receiver Tanks (DCRTs) are actively ventilated, along with certain single-shell tanks (SSTs) and other RPP facilities. The exhaust air stream on a typical primary ventilation system is drawn through two stages of high-efficiency particulate air (HEPA) filtration to ensure confinement of airborne radioactive materials. Active ventilation exhaust stacks require a stack CAM interlock to detect releases from postulated accidents, and to shut down the exhaust fan when high radiation levels are detected in the stack airstream. The stack CAM interlock is credited as a mitigating control to stop continued unfiltered radiological and toxicological discharges from the stack, which may result from an accident involving failure of a HEPA filter. This document defines the initial technical design baseline for a HEPA filter AP fan interlock system.

  19. Testing cleanable/reuseable HEPA prefilters for mixed waste incinerator air pollution control systems

    SciTech Connect

    Burns, D.B.; Wong, A.; Walker, B.W.; Paul, J.D.

    1997-08-01

    The Consolidated Incineration Facility (CIF) at the US DOE Savannah River Site is undergoing preoperational testing. The CIF is designed to treat solid and liquid RCRA hazardous and mixed wastes from site operations and clean-up activities. The technologies selected for use in the air pollution control system (APCS) were based on reviews of existing incinerators, air pollution control experience, and recommendations from consultants. This approach resulted in a facility design using experience from other operating hazardous/radioactive incinerators. In order to study the CIF APCS prior to operation, a 1/10 scale pilot facility, the Offgas Components Test Facility (OCTF), was constructed and has been in operation since late 1994. Its mission is to demonstrate the design integrity of the CIF APCS and optimize equipment/instrument performance of the full scale production facility. Operation of the pilot facility has provided long-term performance data of integrated systems and critical facility components. This has reduced facility startup problems and helped ensure compliance with facility performance requirements. Technical support programs assist in assuring all stakeholders the CIF can properly treat combustible hazardous, mixed, and low-level radioactive wastes. High Efficiency Particulate Air (HEPA) filters are used to remove hazardous and radioactive particulates from the exhaust gas strewn before being released into the atmosphere. The HEPA filter change-out frequency has been a potential issue and was the first technical issue to be studied at the OCTF. Tests were conducted to evaluate the performance of HEPA filters under different operating conditions. These tests included evaluating the impact on HEPA life of scrubber operating parameters and the type of HEPA prefilter used. This pilot-scale testing demonstrated satisfactory HEPA filter life when using cleanable metal prefilters and high flows of steam and water in the offgas scrubber. 8 figs., 2 tabs.

  20. An adaptation of the human HepaRG cells to the in vitro micronucleus assay.

    PubMed

    Jossé, Rozenn; Rogue, Alexandra; Lorge, Elisabeth; Guillouzo, André

    2012-05-01

    The in vitro micronucleus test is considered as an attractive tool for genotoxicity testing of chemicals because of its simplicity of scoring and wide applicability in different cell types. However, most of the cells currently in use are devoid of the enzyme equipment required for activation of promutagens in the genotoxic metabolites. We postulated that the human HepaRG cell line, which can express xenobiotic metabolising enzymes at levels close to those found in primary human hepatocytes and has retained the indefinite growth capacity of transformed cells, could represent a more suitable model for genotoxicity testing of chemicals requiring metabolic activation. Based on the recommendations of the Organisation for Economic Co-operation and Development test guideline TG 487 for testing of chemicals, HepaRG cell cultures containing >80% mature hepatocytes were treated in situ with various chemicals for 24 h followed by a 3-day mitogenic stimulation with epidermal growth factor without cytokinesis block. In such culture conditions, HepaRG cells underwent >1.5 cell cycle per cell during the mitogenic stimulation. While non-genotoxic compounds (mannitol and staurosporine) did not increase the rate of micronucleated mononucleated cells, all aneugens (colchicine, nocodazole and dichlorodiphenyldichloroethylene) as well as the direct acting clastogen methyl methanesulfonate and clastogens requiring metabolic activation (aflatoxin B1, benzo(a)pyrene and 2-nitrofluorene) induced a statistically significant concentration-related increase in the number of mono-micronucleated cells. The micronucleus test was also performed after 7-day repeat exposure of HepaRG cells to the chemicals. Noticeably, a time-dependent effect was obtained with the three clastogens requiring metabolic activation. In conclusion, our results obtained with HepaRG hepatocytes exposed to various genotoxic compounds requiring or not bioactivation, compared favorably with those reported in various other

  1. Summary of meeting on disposal of LET&D HEPA filters

    SciTech Connect

    Not Available

    1991-11-21

    This report is a compilation of correspondence between Westinghouse Idaho Nuclear Company and the US EPA over a period of time from 1988 to 1992 (most from 1991-92) regarding waste management compliance with EPA regulations. Typical subjects include: compliance with satellite accumulation requirements; usage of ``Sure Shot`` containers in place of aerosol cans; notice of upcoming recyclable battery shipments; disposition of batteries; HEPA filter leach sampling and permit impacts; functional and operation requirements for the spent filter handling system; summary of meeting on disposal of LET and D HEPA filters; solvent substitution database report; and mercury vapor light analytical testing.

  2. Face washing promotion for preventing active trachoma

    PubMed Central

    Ejere, Henry OD; Alhassan, Mahmoud B; Rabiu, Mansur

    2015-01-01

    Background Trachoma remains a major cause of avoidable blindness among underprivileged populations in many developing countries. It is estimated that about 146 million people have active trachoma and nearly six million people are blind due to complications associated with repeat infections. Objectives The objective of this review was to assess the effects of face washing promotion for the prevention of active trachoma in endemic communities. Search methods We searched CENTRAL (which contains the Cochrane Eyes and Vision Group Trials Register) (2015, Issue 1), Ovid MEDLINE, Ovid MEDLINE In-Process and Other Non-Indexed Citations, Ovid MEDLINE Daily, Ovid OLDMEDLINE (January 1946 to January 2015), EMBASE (January 1980 to January 2015), PubMed (January 1948 to January 2015), Latin American and Caribbean Health Sciences Literature Database (LILACS) (January 1982 to January 2015), the metaRegister of Controlled Trials (mRCT) (www.controlled-trials.com) (accessed 10 January 2014), ClinicalTrials.gov (www.clinicaltrials.gov) and the World Health Organization (WHO) International Clinical Trials Registry Platform (ICTRP) (www.who.int/ictrp/search/en). We did not use any date or language restrictions in the electronic searches for trials. We last searched the electronic databases on 26 January 2015. To identify further relevant trials we checked the reference lists of the included trials. Also, we used the Science Citation Index to search for references to publications that cited the trials included in the review. We contacted investigators and experts in the field to identify additional trials. Selection criteria We included randomized controlled trials (RCTs) or quasi-RCTs that compared face washing with no treatment or face washing combined with antibiotics against antibiotics alone. Trial participants were residents of endemic trachoma communities. Data collection and analysis Two review authors independently extracted data and assessed trial quality. We contacted trial

  3. 7 CFR 58.429 - Washing machine.

    Code of Federal Regulations, 2012 CFR

    2012-01-01

    ... 7 Agriculture 3 2012-01-01 2012-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  4. 7 CFR 58.429 - Washing machine.

    Code of Federal Regulations, 2013 CFR

    2013-01-01

    ... 7 Agriculture 3 2013-01-01 2013-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  5. 7 CFR 58.429 - Washing machine.

    Code of Federal Regulations, 2014 CFR

    2014-01-01

    ... 7 Agriculture 3 2014-01-01 2014-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  6. 7 CFR 58.429 - Washing machine.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... 7 Agriculture 3 2011-01-01 2011-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  7. 7 CFR 58.429 - Washing machine.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Washing machine. 58.429 Section 58.429 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....429 Washing machine. When used, the washing machine for cheese cloths and bandages shall be...

  8. 21 CFR 1250.87 - Wash water.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 8 2013-04-01 2013-04-01 false Wash water. 1250.87 Section 1250.87 Food and Drugs... Sanitation Facilities and Conditions on Vessels § 1250.87 Wash water. Where systems installed on vessels for wash water, as defined in § 1250.3(n), do not comply with the requirements of a potable water...

  9. 21 CFR 1250.87 - Wash water.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Wash water. 1250.87 Section 1250.87 Food and Drugs... Sanitation Facilities and Conditions on Vessels § 1250.87 Wash water. Where systems installed on vessels for wash water, as defined in § 1250.3(n), do not comply with the requirements of a potable water...

  10. 21 CFR 1250.87 - Wash water.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 8 2014-04-01 2014-04-01 false Wash water. 1250.87 Section 1250.87 Food and Drugs... Sanitation Facilities and Conditions on Vessels § 1250.87 Wash water. Where systems installed on vessels for wash water, as defined in § 1250.3(n), do not comply with the requirements of a potable water...

  11. 21 CFR 1250.87 - Wash water.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 8 2011-04-01 2011-04-01 false Wash water. 1250.87 Section 1250.87 Food and Drugs... Sanitation Facilities and Conditions on Vessels § 1250.87 Wash water. Where systems installed on vessels for wash water, as defined in § 1250.3(n), do not comply with the requirements of a potable water...

  12. 21 CFR 1250.87 - Wash water.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 8 2012-04-01 2012-04-01 false Wash water. 1250.87 Section 1250.87 Food and Drugs... Sanitation Facilities and Conditions on Vessels § 1250.87 Wash water. Where systems installed on vessels for wash water, as defined in § 1250.3(n), do not comply with the requirements of a potable water...

  13. Alternative Antimicrobial Commercial Egg Washing Procedures

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Commercial table eggs are washed prior to packaging. Standard wash procedures use an alkaline pH and warm water. If a cool water method could be developed that would still provide a microbiologically safe egg, the industry may save energy costs associated with water heating. Four wash procedures ...

  14. FULL SCALE REGENERABLE HEPA FILTER DESIGN USING SINTERED METAL FILTER ELEMENTS

    SciTech Connect

    Gil Ramos; Kenneth Rubow; Ronald Sekellick

    2002-11-27

    A Department of Energy funded contract involved the development of porous metal as a HEPA filter, and the subsequent design of a full-scale regenerable HEPA filtration system (RHFS). This RHFS could replace the glass fiber HEPA filters currently being used on the high level waste (HLW) tank ventilation system with a system that would be moisture tolerant, durable, and cleanable in place. The origins of the contract are a 1996 investigation at the Savannah River Technology Center (SRTC) regarding the use of porous metal as a HEPA filter material. This contract was divided into Phases I, IIA and IIB. Phase I of the contract evaluated simple filter cylinders in a simulated High Level Waste (HLW) environment and the ability to clean and regenerate the filter media after fouling. Upon the successful completion of Phase I, Phase IIA was conducted, which included lab scale prototype testing and design of a full-scale system. The work completed under Phase IIA included development of a full-scale system design, development of a filter media meeting the HEPA filtration efficiency that would also be regenerable using prescribed cleaning procedures, and the testing of a single element system prototype at Savannah River. All contract objectives were met. The filter media selected was a nickel material already under development at Mott, which met the HEPA filtration efficiency standard. The Mott nickel media met and exceeded the HEPA requirement, providing 99.99% removal against a requirement of 99.97%. Double open-ended elements of this media were provided to the Savannah River Test Center for HLW simulation testing in the single element prototype filter. These elements performed well and further demonstrated the practicality of a metallic media regenerable HEPA filter system. An evaluation of the manufacturing method on many elements demonstrated the reproducibility to meet the HEPA filtration requirement. The full-scale design of the Mott RHFS incorporated several important

  15. Axial Dispersion during Hanford Saltcake Washing

    SciTech Connect

    Josephson, Gary B.; Geeting, John GH; Lessor, Delbert L.; Barton, William B.

    2006-08-01

    Clean up of Hanford salt cake wastes begins with dissolution retrieval of the sodium rich salts that make up the dominant majority of mass in the tanks. Water moving through the porous salt cake dissolves the soluble components and also displaces the soluble radionuclides (e.g. 137Cs and 99TcO4- ). The separation that occurs from this displacement, known as Selective dissolution, is an important component in Hanford’s pretreatment of low activity wastes for subsequent Supplemental treatment. This paper describes lab scale testing conducted to evaluate Selective dissolution of cesium from non-radioactive Hanford tank 241-S-112 salt cake simulant containing the primary chemicals found the the actual tank. An modified axial dispersion model with increasing axial dispersion was developed to predict cesium removal. The model recognizes that water dissolves the salt cake during washing, which causes an increase in the axial dispersion during the wash. This model was subsequently compared with on-line cesium measurements from the retrieval of tank 241-S-112. The model had remarkably good agreement with both the lab scale and full scale data.

  16. Whole-head washing, prior to cutting, provides sanitization advantages for fresh-cut Iceberg lettuce (Latuca sativa L.).

    PubMed

    Palma-Salgado, Sindy; Pearlstein, Arne J; Luo, Yaguang; Park, Hee Kyung; Feng, Hao

    2014-06-01

    The efficacy of two leafy produce wash methods, the traditional cutting-before-washing process and a new washing-before-cutting method, on reduction of Escherichia coli O157:H7 inoculated on Iceberg lettuce was compared. The washing tests were conducted in a pilot-scale washer using combinations of water, chlorine, peroxyacetic acid, and ultrasound. The washing-before-cutting process recorded an E. coli O157:H7 count reduction 0.79-0.80 log₁₀ CFU/g higher than that achieved with the cutting-before-washing process in treatments involving only a sanitizer. When ultrasound was applied to the washing-before-cutting process, a further improvement of 0.37-0.68 log₁₀ CFU/g in microbial count reduction was obtained, reaching total reductions of 2.43 and 2.24 log₁₀ CFU/g for chlorine and peroxyacetic acid washes, respectively. PMID:24704862

  17. Applied patent RFID systems for building reacting HEPA air ventilation system in hospital operation rooms.

    PubMed

    Lin, Jesun; Pai, Jar-Yuan; Chen, Chih-Cheng

    2012-12-01

    RFID technology, an automatic identification and data capture technology to provide identification, tracing, security and so on, was widely applied to healthcare industry in these years. Employing HEPA ventilation system in hospital is a way to ensure healthful indoor air quality to protect patients and healthcare workers against hospital-acquired infections. However, the system consumes lots of electricity which cost a lot. This study aims to apply the RFID technology to offer a unique medical staff and patient identification, and reacting HEPA air ventilation system in order to reduce the cost, save energy and prevent the prevalence of hospital-acquired infection. The system, reacting HEPA air ventilation system, contains RFID tags (for medical staffs and patients), sensor, and reacting system which receives the information regarding the number of medical staff and the status of the surgery, and controls the air volume of the HEPA air ventilation system accordingly. A pilot program was carried out in a unit of operation rooms of a medical center with 1,500 beds located in central Taiwan from Jan to Aug 2010. The results found the air ventilation system was able to function much more efficiently with less energy consumed. Furthermore, the indoor air quality could still keep qualified and hospital-acquired infection or other occupational diseases could be prevented.

  18. Effect of Circulation Parameters on Functional Status of HepaRG Spheroids Cultured in Microbioreactor.

    PubMed

    Semenova, O V; Petrov, V A; Gerasimenko, T N; Aleksandrova, A V; Burmistrova, O A; Khutornenko, A A; Osipyants, A I; Poloznikov, A A; Sakharov, D A

    2016-07-01

    We studied the relationship between microcirculation parameters and functional status of HepaRG cells in spheroids and chose an optimal regimen within the physiologically permissible limits of mechanical impact for the cells that maintains the expression of functional genes of the liver. PMID:27496037

  19. Potential for HEPA filter damage from water spray systems in filter plenums

    SciTech Connect

    Bergman, W.; Fretthold, J.K.; Slawski, J.W.

    1997-08-01

    The water spray systems in high efficiency particulate air (HEPA) filter plenums that are used in nearly all Department of Energy (DOE) facilities for protection against fire was designed under the assumption that the HEPA filters would not be damaged by the water sprays. The most likely scenario for filter damage involves filter plugging by the water spray, followed by the fan blowing out the filter medium. A number of controlled laboratory tests that were previously conducted in the late 1980s are reviewed in this paper to provide a technical basis for the potential HEPA filter damage by the water spray system in HEPA filter plenums. In addition to the laboratory tests, the scenario for BEPA filter damage during fires has also occurred in the field. A fire in a four-stage, BEPA filter plenum at Rocky Flats in 1980 caused the first three stages of BEPA filters to blow out of their housing and the fourth stage to severely bow. Details of this recently declassified fire are presented in this paper. Although these previous findings suggest serious potential problems exist with the current water spray system in filter plenums, additional studies are required to confirm unequivocally that DOE`s critical facilities are at risk. 22 refs., 15 figs.

  20. Software Verification and Validation Test Report for the HEPA filter Differential Pressure Fan Interlock System

    SciTech Connect

    ERMI, A.M.

    2000-09-05

    The HEPA Filter Differential Pressure Fan Interlock System PLC ladder logic software was tested using a Software Verification and Validation (V&V) Test Plan as required by the ''Computer Software Quality Assurance Requirements''. The purpose of his document is to report on the results of the software qualification.

  1. BERGMANN USA SOIL SEDIMENT WASHING TECHNOLOGY - APPLICATIONS ANALYSIS REPORT

    EPA Science Inventory

    This document provides an evaluation of the performance of the Bergmann USA Soil/Sediment Washing System and its applicability for the treatment of soils or sediments contaminated with organic and/or inorganic compounds. Both the technical and economic aspects of the technology w...

  2. WASHING STUDIES FOR PCP AND CREOSOTE-CONTAMINATED SOIL

    EPA Science Inventory

    The Environmental Protection Agency has conducted a series of bench-scale and pilot-scale studies to evaluate the feasibility of washing pentachlorophenol (PCP) and creosote from the soil at an abandoned wood-treatment Superfund site in Pensacola, FL. The high sand content and lo...

  3. Differential toxicity of heterocyclic aromatic amines and their mixture in metabolically competent HepaRG cells

    SciTech Connect

    Dumont, Julie; Josse, Rozenn; Lambert, Carine; Antherieu, Sebastien; Le Hegarat, Ludovic; Aninat, Caroline; Robin, Marie-Anne; Guguen-Guillouzo, Christiane

    2010-06-01

    Human exposure to heterocyclic aromatic amines (HAA) usually occurs through mixtures rather than individual compounds. However, the toxic effects and related mechanisms of co-exposure to HAA in humans remain unknown. We compared the effects of two of the most common HAA, 2-amino-1-methyl-6-phenylimidazo[4,5-b]pyridine (PhIP) and 2-amino-3,8-dimethylimidazo[4,5-f]quinoxaline (MeIQx), individually or in combination, in the metabolically competent human hepatoma HepaRG cells. Various endpoints were measured including cytotoxicity, apoptosis, oxidative stress and DNA damage by the comet assay. Moreover, the effects of PhIP and/or MeIQx on mRNA expression and activities of enzymes involved in their activation and detoxification pathways were evaluated. After a 24 h treatment, PhIP and MeIQx, individually and in combination, exerted differential effects on apoptosis, oxidative stress, DNA damage and cytochrome P450 (CYP) activities. Only PhIP induced DNA damage. It was also a stronger inducer of CYP1A1 and CYP1B1 expression and activity than MeIQx. In contrast, only MeIQx exposure resulted in a significant induction of CYP1A2 activity. The combination of PhIP with MeIQx induced an oxidative stress and showed synergistic effects on apoptosis. However, PhIP-induced genotoxicity was abolished by a co-exposure with MeIQx. Such an inhibitory effect could be explained by a significant decrease in CYP1A2 activity which is responsible for PhIP genotoxicity. Our findings highlight the need to investigate interactions between HAA when assessing risks for human health and provide new insights in the mechanisms of interaction between PhIP and MeIQx.

  4. [Bactericidal power's assessment of eight antiseptic products intended to surgeon's hand-washing (author's transl)].

    PubMed

    Charrel, J; Gevaudan, M J; Mallet, M N; Blancard, A; Gevaudan, P

    1977-01-01

    A standard hand-washing technique was used in order to test the relative effectiveness of eight both detergent and alcoholic preparations intended to surgeon's hands disinfection. A single four or seven minutes washing with alcoholic solutions was shown to eliminate a much larger proportion of the skin flora than could be removed by a single four or seven minutes hand-washing with detergent antiseptic preparations. Authors have also determined effect of wearing surgical rubber gloves after skin disinfection and compared viable bacterial counts in hand washings immediately after the antiseptic treatment and when gloves had been worn for one hour.

  5. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTHEAST. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTHEAST. THE ELECTRIC TROLLEY IS SEEN AT THE LEFT. THE BULKHEAD SEEN AT THE LOWER RIGHT IS NOT PART OF THE MACHINE; IT WAS INSTALLED TO RETAIN THE FILTER SAND AFTER THE MACHINE WAS NO LONGER USED. THE NORTHWEST CORNER OF SETTLING RESERVOIR NO. 4 IS SEEN IN THE DISTANCE BELOW THE RIGHT SIDE OF THE TROLLEY. - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  6. BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTH. THE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    BLAISDELL SLOW SAND FILTER WASHING MACHINE. VIEW LOOKING SOUTH. THE SUCTION (INTAKE) HOSE IS SEEN AT THE LEFT RESTING ON THE FILTER BED SURFACE; THE DISCHARGE HOSE IS AT THE RIGHT, RUNNING FROM THE BOTTOM OF THE CENTRAL VERTICAL AXLE TO THE CENTRIFUGAL PUMP. FROM THE PUMP WATER IS DISCHARGED THROUGH THE HORIZONTAL PIPE LOCATED UNDER THE EDGE OF PLATFORM DECK INTO THE WASTE-WATER TROUGH (NOT SEEN IN THIS VIEW). - Yuma Main Street Water Treatment Plant, Blaisdell Slow Sand Filter Washing Machine, Jones Street at foot of Main Street, Yuma, Yuma County, AZ

  7. Electrical Switchability and Dry-Wash Durability of Conductive Textiles

    NASA Astrophysics Data System (ADS)

    Wu, Bangting; Zhang, Bowu; Wu, Jingxia; Wang, Ziqiang; Ma, Hongjuan; Yu, Ming; Li, Linfan; Li, Jingye

    2015-06-01

    There is growing interest in the area of conductive textiles in the scientific and industrial community. Herein, we successfully prepared a conductive textile via covalently grafting polyaniline (PANI) onto cotton by a multi-step treatment process. The conductivity of the resultant fabric could be tuned by immersing in water having different pH values. The conductive and insulating properties of the textile could be conveniently switched by alternately immersing in acidic and alkaline bath solutions. Most importantly, the resultant conductive fabrics were able to withstand 40 simulated dry-wash cycles, with almost no decay in the electrical conductivity, indicating their excellent dry-wash durability. The present strategy for fabricating conductive fabrics with excellent switchability of electrical properties and dry-wash durability is expected to provide inspiration for the production of multifunctional conductive textiles for use in hash or sensitive conditions.

  8. Electrical Switchability and Dry-Wash Durability of Conductive Textiles

    PubMed Central

    Wu, Bangting; Zhang, Bowu; Wu, Jingxia; Wang, Ziqiang; Ma, Hongjuan; Yu, Ming; Li, Linfan; Li, Jingye

    2015-01-01

    There is growing interest in the area of conductive textiles in the scientific and industrial community. Herein, we successfully prepared a conductive textile via covalently grafting polyaniline (PANI) onto cotton by a multi-step treatment process. The conductivity of the resultant fabric could be tuned by immersing in water having different pH values. The conductive and insulating properties of the textile could be conveniently switched by alternately immersing in acidic and alkaline bath solutions. Most importantly, the resultant conductive fabrics were able to withstand 40 simulated dry-wash cycles, with almost no decay in the electrical conductivity, indicating their excellent dry-wash durability. The present strategy for fabricating conductive fabrics with excellent switchability of electrical properties and dry-wash durability is expected to provide inspiration for the production of multifunctional conductive textiles for use in hash or sensitive conditions. PMID:26066704

  9. Predicting mass loading as a function of pressure difference across prefilter/HEPA filter systems

    SciTech Connect

    Novick, V.J.; Klassen, J.F. ); Monson, P.R. )

    1992-01-01

    The purpose of this work is to develop a methodology for predicting the mass loading and pressure drop effects on a prefilter/ HEPA filter system. The methodology relies on the use of empirical equations for the specific resistance of the aerosol loaded filter as a function of the particle diameter. These correlations relate the pressure difference across a filter to the mass loading on the filter and accounts for aerosol particle density effects. These predictions are necessary for the efficient design of new filtration systems and for risk assessment studies of existing filter systems. This work specifically addresses the prefilter/HEPA filter Airborne Activity Confinement Systems (AACS) at the Savannah River Plant. In order to determine the mass loading on the system, it is necessary to establish the efficiency characteristics for the prefilter, the mass loading characteristics of the prefilter measured as a function of pressure difference across the prefilter, and the mass loading characteristics of the HEPA filter as a function of pressure difference across the filter. Furthermore, the efficiency and mass loading characteristics need to be determined as a function of the aerosol particle diameter. A review of the literature revealed that no previous work had been performed to characterize the prefilter material of interest. In order to complete the foundation of information necessary to predict total mass loadings on prefilter/HEPA filter systems, it was necessary to determine the prefilter efficiency and mass loading characteristics. The measured prefilter characteristics combined with the previously determined HEPA filter characteristics allowed the resulting pressure difference across both filters to be predicted as a function of total particle mass for a given particle distribution. These predictions compare favorably to experimental measurements ({plus minus}25%).

  10. Test plan for N2 HEPA filters assembly shop stock used on PFP E4 exhaust system

    SciTech Connect

    DICK, J.D.

    1999-09-01

    At Plutonium Finishing Plant (PFP) and Plutonium Reclamation Facility (PRF) Self-contained HEPA filters, encased in wooden frames and boxes, are installed in the E4 Exhaust Ventilation System to provide confinement of radioactive releases to the environment and confinement of radioactive contamination within designated zones inside the facility. Recently during the routine testing in-leakage was discovered downstream of the Self-contained HEPA filters boxes. This Test Plan describes the approach to conduct investigation of the root causes for the in-leakage of HEPA filters.

  11. Fostering Hand Washing before Lunch by Students Attending a Special Needs Young Adult Program

    ERIC Educational Resources Information Center

    Walmsley, Christopher; Mahoney, Amanda; Durgin, Amy; Poling, Alan

    2013-01-01

    A multiple baseline across groups design was used to investigate the effects of a treatment package on hand washing before lunch by five students with disabilities who attended a young adult educational program. To evaluate hand washing, a lotion called Glo Germ was applied to participants' hands. Glo Germ is visible under a black light, which…

  12. EFRT M-12 Issue Resolution: Solids Washing

    SciTech Connect

    Baldwin, David L.; Schonewill, Philip P.; Toth, James J.; Huckaby, James L.; Eslinger, Paul W.; Hanson, Brady D.; Kurath, Dean E.; Minette, Michael J.

    2010-01-01

    Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project-Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to perform research and development activities to resolve technical issues identified for the Pretreatment Facility (PTF). The Pretreatment Engineering Platform (PEP) was designed, constructed, and operated as part of a plan to respond to issue M12, “Undemonstrated Leaching Processes” of the External Flowsheet Review Team (EFRT) issue response plan.( ) The PEP is a 1/4.5-scale test platform designed to simulate the WTP pretreatment caustic leaching, oxidative leaching, ultrafiltration solids concentration, and slurry washing processes. The PEP replicates the WTP leaching processes using prototypic equipment and control strategies. The PEP also includes non-prototypic ancillary equipment to support the core processing.

  13. Postoperative washing of sutured wounds.

    PubMed

    Harrison, Conrad; Wade, Cian; Gore, Sinclair

    2016-11-01

    A best evidence topic was written according to the structured protocol. The three part question addressed was: [In patients undergoing closure of surgical wounds with sutures] does [keeping the wound dry for the first 48 h after closure] [reduce the incidence of surgical site infections (SSIs)]? 4 relevant papers were culled from the literature and appraised. The authors, date, country, population, study type, main outcomes, key results and study weaknesses were tabulated. Current NICE guidelines recommend cleaning surgical wounds with sterile saline only for the first 48 h following skin closure. We found no evidence that washing wounds with tap water during this period increases the incidence of SSIs compared to keeping them dry. Further randomised controlled trials will enable the construction of conclusive systematic reviews and meta-analyses. PMID:27668079

  14. Wash water waste pretreatment system

    NASA Technical Reports Server (NTRS)

    1977-01-01

    Investigations were completed on wash waters based on each candidate personal cleansing agent. Evaluations of coagulants, antifoam agents, and the effect of promising antifoams on the chemical precipitation were included. Based on these evaluations two candidate soaps as well as their companion antifoam agents were selected for further work. Operating parameters included the effect of soap concentration, ferric chloride concentration, duration of mixing, and pore size of depth filters on the degree of soap removal. The effect of pressure on water flow through filter cartridges and on the rate of decline of water flow was also investigated. The culmination of the program was the recommendation of a pretreatment concept based on chemical precipitation followed by pressure filtration.

  15. Bathing or washing babies after birth?

    PubMed

    Henningsson, A; Nyström, B; Tunnell, R

    One group of healthy full-term newborn babies was washed after birth and another was bathed to remove vernix caseosa and clean the skin. Few infections, none of them serious, occurred in either group. Bacterial colonisation of the umbilical cord on the third day of life was similar in both groups. The rectal temperature fell further and more infants cried during washing than during bathing. Thus bathing the baby after birth makes it calmer, quieter, and more comfortable than washing and causes less heat-loss. Clinical signs of infection and bacterial colonisation rates are no higher after bathing than after washing. PMID:6118769

  16. Microfluidic chemical processing with on-chip washing by deterministic lateral displacement arrays with separator walls

    PubMed Central

    Chen, Yu; D'Silva, Joseph; Austin, Robert H.; Sturm, James C.

    2015-01-01

    We describe a microfluidic device for on-chip chemical processing, such as staining, and subsequent washing of cells. The paper introduces “separator walls” to increase the on-chip incubation time and to improve the quality of washing. Cells of interest are concentrated into a treatment stream of chemical reagents at the first separator wall for extended on-chip incubation without causing excess contamination at the output due to diffusion of the unreacted treatment chemicals, and then are directed to the washing stream before final collections. The second separator wall further reduces the output contamination from diffusion to the washing stream. With this approach, we demonstrate on-chip leukocyte staining with Rhodamine 6G and washing. The results suggest that other conventional biological and analytical processes could be replaced by the proposed device. PMID:26396659

  17. Evaluation of the effect of media velocity on HEPA filter performance

    SciTech Connect

    Alderman, Steven; Parsons, Michael; Hogancamp, Kristina; Norton, O. Perry; Waggoner, Charles

    2007-07-01

    Section FC of the ASME AG-1 Code addresses glass fiber HEPA filters and restricts the media velocity to a maximum of 2.54 cm/s (5 ft/min). Advances in filter media technology allow glass fiber HEPA filters to function at significantly higher velocities and still achieve HEPA performance. However, diffusional capture of particles < 100 nm is reduced at higher media velocities due to shorter residence times within the media matrix. Therefore, it is unlikely that higher media velocities for HEPA filters will be allowed without data to demonstrate the effect of media velocity on removal of particles in the smaller size classes. In order to address this issue, static testing has been conducted to generate performance related data and a range of dynamic testing has provided data regarding filter lifetimes, loading characteristics, changes in filter efficiency and the most penetrating particle size over time. Testing was conducted using 31 cm x 31 cm x 29 cm deep pleat HEPA filters supplied from two manufacturers. Testing was conducted at media velocities ranging from 2.0-4.5 cm/s with a solid aerosol challenge composed of potassium chloride. Two set of media velocity data were obtained for each filter type. In one set of evaluations, the maximum aerosol challenge particle size was limited to 3 {mu}m, while particles above 3 {mu}m were not constrained in the second set. This provided for considerable variability in the challenge mass mean diameter and overall mass loading rate. Results of this testing will be provided to the ASME AG-1 FC Committee for consideration in future versions of the HEPA standard. In general, the initial filter efficiency decreased with increasing media velocity. However, initial filter efficiencies were generally good in all cases. Filter efficiency values averaged over the first ten minute of the loading cycle ranged from 99.970 to 99.996 %. Additionally, the most penetrating particle size was observed to decrease with increasing media velocity

  18. Closed circuit rebreathing to achieve inert gas wash-in for multiple breath wash-out

    PubMed Central

    O'Neill, Katherine; Downey, Damian G.; Elborn, J. Stuart; Bell, Nicholas J.; Smith, Jaclyn; Owers-Bradley, John

    2016-01-01

    Multiple breath wash-out (MBW) testing requires prior wash-in of inert tracer gas. Wash-in efficiency can be enhanced by a rebreathing tracer in a closed circuit. Previous attempts to deploy this did not account for the impact of CO2 accumulation on patients and were unsuccessful. We hypothesised that an effective rebreathe wash-in could be delivered and it would not alter wash-out parameters. Computer modelling was used to assess the impact of the rebreathe method on wash-in efficiency. Clinical testing of open and closed circuit wash-in–wash-out was performed in healthy controls and adult patients with cystic fibrosis (CF) using a circuit with an effective CO2 scrubber and a refined wash-in protocol. Wash-in efficiency was enhanced by rebreathing. There was no difference in mean lung clearance index between the two wash-in methods for controls (6.5 versus 6.4; p=0.2, n=12) or patients with CF (10.9 versus 10.8; p=0.2, n=19). Test time was reduced by rebreathe wash-in (156 versus 230 s for CF patients, p<0.001) and both methods were well tolerated. End wash-in CO2 was maintained below 2% in most cases. Rebreathe–wash-in is a promising development that, when correctly deployed, reduces wash-in time and facilitates portable MBW testing. For mild CF, wash-out outcomes are equivalent to an open circuit. PMID:27730167

  19. Particle size for greatest penetration of HEPA filters - and their true efficiency

    SciTech Connect

    da Roza, R.A.

    1982-12-01

    The particle size that most greatly penetrates a filter is a function of filter media construction, aerosol density, and air velocity. In this paper the published results of several experiments are compared with a modern filtration theory that predicts single-fiber efficiency and the particle size of maximum penetration. For high-efficiency particulate air (HEPA) filters used under design conditions this size is calculated to be 0.21 ..mu..m diam. This is in good agreement with the experimental data. The penetration at 0.21 ..mu..m is calculated to be seven times greater than at the 0.3 ..mu..m used for testing HEPA filters. Several mechanisms by which filters may have a lower efficiency in use than when tested are discussed.

  20. Feasibility study for an additional HEPA filter leaching system in NWCF

    SciTech Connect

    Willis, W.D.

    1992-11-01

    This report documents the feasibility of installing a second high-efficiency particulate air (HEPA) filter leaching system in the New Waste Calcining Facility at the Idaho Chemical Processing Plant (ICPP). A large spent filter backlog already exists at the ICPP, and it has been uncertain whether the existing HEPA filter leaching system will have a throughput rate sufficient to work off the existing backlog in a timely manner. Three areas within the New Waste Calcining Facility (NWCF) have been identified as possible locations for a second filter leaching system. This report examines the suitability of each location, identifies modifications that would be necessary-to install a filter leaching system at each location, examines the impact of modifying each location, and discusses recent efforts to estimate filter throughput using the existing filter leaching system. Based on all available information, installation of a second filter leaching system is not recommended at the present time.

  1. Verification of HEPA Filter Analysis for the Canberra Q2 Waste Assay System

    SciTech Connect

    Casella, V.R.

    2002-12-06

    Data from measurements of a standard 20 inches x 20 inches source positioned on the end and in the middle of a HEPA filter verified that assaying HEPA filters with the Canberra Q2 and using the standard drum calibration with a percent full parameter of 70 percent gives acceptable results for gamma rays above 122 keV. For the gamma-ray energy range of 122 keV to 1400 keV, nuclide concentrations would be somewhat overestimated by from about 35 percent (122 keV) to about 10 percent (1400 keV). Also, Am-241 (60 keV) is conservatively overestimated by about a factor of 2.6 using this configuration.

  2. Inhibition Of Washed Sludge With Sodium Nitrite

    SciTech Connect

    Congdon, J. W.; Lozier, J. S.

    2012-09-25

    This report describes the results of electrochemical tests used to determine the relationship between the concentration of the aggressive anions in washed sludge and the minimum effective inhibitor concentration. Sodium nitrate was added as the inhibitor because of its compatibility with the DWPF process. A minimum of 0.05M nitrite is required to inhibit the washed sludge simulant solution used in this study. When the worst case compositions and safety margins are considered, it is expected that a minimum operating limit of nearly 0.1M nitrite will be specified. The validity of this limit is dependent on the accuracy of the concentrations and solubility splits previously reported. Sodium nitrite additions to obtain 0.1M nitrite concentrations in washed sludge will necessitate the additional washing of washed precipitate in order to decrease its sodium nitrite inhibitor requirements sufficiently to remain below the sodium limits in the feed to the DWPF. Nitrite will be the controlling anion in "fresh" washed sludge unless the soluble chloride concentration is about ten times higher than predicted by the solubility splits. Inhibition of "aged" washed sludge will not be a problem unless significant chloride dissolution occurs during storage. It will be very important tomonitor the composition of washed sludge during processing and storage.

  3. Radioactive air emissions notice of construction HEPA filtered vacuum radioactive air emission units

    SciTech Connect

    JOHNSON, R.E.

    1999-09-01

    This notice of construction (NOC) requests a categorical approval for construction and operation of certain portable high-efficiency particulate air (HEPA) filtered vacuum radionuclide airborne emission units (HVUs). Approval of this NOC application is intended to allow operation of the HVUs without prior project-specific approval. This NOC does not request replacement or supersedence of any previous agreements/approvals by the Washington State Department of Health for the use of vacuums on the Hanford Site. These previous agreement/approvals include the approved NOCs for the use of EuroClean HEPA vacuums at the T Plant Complex (routine technical meeting 12/10/96) and the Kelly Decontamination System at the Plutonium-Uranium Extraction (PUREX) Plant (routine technical meeting 06/25/96). Also, this NOC does not replace or supersede the agreement reached regarding the use of HEPA hand-held/shop-vacuum cleaners for routine cleanup activities conducted by the Environmental Restoration Project. Routine cleanup activities are conducted during the surveillance and maintenance of inactive waste sites (Radioactive Area Remedial Action Project) and inactive facilities. HEPA hand-held/shop-vacuum cleaners are used to clean up spot surface contamination areas found during outdoor radiological field surveys, and to clean up localized radiologically contaminated material (e.g., dust, dirt, bird droppings, animal feces, liquids, insects, spider webs, etc.). This agreement, documented in the October 12, 1994 Routine Meeting Minutes, is based on routine cleanup consisting of spot cleanup of low-level contamination provided that, in each case, the source term potential would be below 0.1 millirem per year.

  4. Comparison of MERV 16 and HEPA filters for cab filtration of underground mining equipment

    PubMed Central

    Cecala, A.B.; Organiscak, J.A.; Noll, J.D.; Zimmer, J.A.

    2016-01-01

    Significant strides have been made in optimizing the design of filtration and pressurization systems used on the enclosed cabs of mobile mining equipment to reduce respirable dust and provide the best air quality to the equipment operators. Considering all of the advances made in this area, one aspect that still needed to be evaluated was a comparison of the efficiencies of the different filters used in these systems. As high-efficiency particulate arrestance (HEPA) filters provide the highest filtering efficiency, the general assumption would be that they would also provide the greatest level of protection to workers. Researchers for the U.S. National Institute for Occupational Safety and Health (NIOSH) speculated, based upon a previous laboratory study, that filters with minimum efficiency reporting value, or MERV rating, of 16 may be a more appropriate choice than HEPA filters in most cases for the mining industry. A study was therefore performed comparing HEPA and MERV 16 filters on two kinds of underground limestone mining equipment, a roof bolter and a face drill, to evaluate this theory. Testing showed that, at the 95-percent confidence level, there was no statistical difference between the efficiencies of the two types of filters on the two kinds of mining equipment. As the MERV 16 filters were less restrictive, provided greater airflow and cab pressurization, cost less and required less-frequent replacement than the HEPA filters, the MERV 16 filters were concluded to be the optimal choice for both the roof bolter and the face drill in this comparative-analysis case study. Another key finding of this study is the substantial improvement in the effectiveness of filtration and pressurization systems when using a final filter design. PMID:27524838

  5. ASME AG-1 Section FC Qualified HEPA Filters; a Particle Loading Comparison - 13435

    SciTech Connect

    Stillo, Andrew; Ricketts, Craig I.

    2013-07-01

    High Efficiency Particulate Air (HEPA) Filters used to protect personnel, the public and the environment from airborne radioactive materials are designed, manufactured and qualified in accordance with ASME AG-1 Code section FC (HEPA Filters) [1]. The qualification process requires that filters manufactured in accordance with this ASME AG-1 code section must meet several performance requirements. These requirements include performance specifications for resistance to airflow, aerosol penetration, resistance to rough handling, resistance to pressure (includes high humidity and water droplet exposure), resistance to heated air, spot flame resistance and a visual/dimensional inspection. None of these requirements evaluate the particle loading capacity of a HEPA filter design. Concerns, over the particle loading capacity, of the different designs included within the ASME AG-1 section FC code[1], have been voiced in the recent past. Additionally, the ability of a filter to maintain its integrity, if subjected to severe operating conditions such as elevated relative humidity, fog conditions or elevated temperature, after loading in use over long service intervals is also a major concern. Although currently qualified HEPA filter media are likely to have similar loading characteristics when evaluated independently, filter pleat geometry can have a significant impact on the in-situ particle loading capacity of filter packs. Aerosol particle characteristics, such as size and composition, may also have a significant impact on filter loading capacity. Test results comparing filter loading capacities for three different aerosol particles and three different filter pack configurations are reviewed. The information presented represents an empirical performance comparison among the filter designs tested. The results may serve as a basis for further discussion toward the possible development of a particle loading test to be included in the qualification requirements of ASME AG-1

  6. Hand washing: changes in the skin flora.

    PubMed

    de Almeida e Borges, Lizandra Ferreira; Silva, Bruno Leonardo; Gontijo Filho, Paulo Pinto

    2007-08-01

    Frequent hand washing may result in skin damage and increase the number of microorganisms that colonize the skin. The purpose of this study was to evaluate changes in total flora of healthy and damaged hands that were caused by the use of gloves, soap, and antiseptics. Samples were collected from the healthy and damaged hands of 30 health care professionals before and after washing with water and nonmedicated soap for the technique of sterile polyethylene bag. Fifteen additional volunteers (technicians and students) were asked to wash their hands 20 times with water and soap; those with complaints of irritation were evaluated separately. Damaged or healthy hands did not present statistically significant differences (P > .05) in terms of qualitative analysis of epidemiologically important microorganisms; however, washing with water and soap was effective only for healthy hands. In short, the water and soap washing of damaged hands was not effective in reducing their contamination.

  7. Viability and functional integrity of washed platelets

    SciTech Connect

    Pineda, A.A.; Zylstra, V.W.; Clare, D.E.; Dewanjee, M.K.; Forstrom, L.A.

    1989-07-01

    The viability and functional integrity of saline- and ACD-saline-washed platelets were compared with those of unwashed platelets. After template bleeding time (TBT) was measured, 15 healthy volunteers underwent plateletpheresis and ingested 600 mg of aspirin. Autologous /sup 111/In-labeled platelets were transfused: unwashed (n = 5), washed with 0.9 percent saline solution (SS) (n = 5), and washed with a buffered 12.6 percent solution of ACD-A in 0.9 percent saline solution (n = 5). After transfusion, we measured TBT at 1, 4, and 24 hours; platelet survival at 10 minutes and 1, 4, and 24 hours and daily for 6 days; and the percentage of uptake in liver and spleen by quantitative whole-body radionuclide scintigraphy at 24 and 190 hours. We found that saline washing affected platelet recovery, 23.47 +/- 12 percent (p less than 0.001) as compared to 52.43 +/- 17 percent (p less than 0.002) for ACD-saline and 73.17 +/- 8 percent for control; that saline washing resulted in a greater liver uptake than control and ACD-saline-washed platelets (31.9 +/- 8% (p less than 0.001) vs 17.7 +/- 4.1 and 19.3 +/- 2.1% (p greater than 0.1), respectively); that, unlike control and ACD-saline-washed platelets, saline-washed platelets did not shorten bleeding time; and that neither type of washing affected survival. Although ACD-saline washing affects recovery, it also results in intact function, normal survival, higher recovery than SS platelets, and no significant liver uptake.

  8. Identification of Enterobacteriaceae from washed and unwashed commercial shell eggs.

    PubMed

    Musgrove, Michael T; Jones, Deana R; Northcutt, Julie K; Cox, Nelson A; Harrison, Mark A

    2004-11-01

    To evaluate the effect of processing on the safety and quality of retail shell eggs, a storage study was conducted with unwashed and commercially washed eggs. This work demonstrated that commercial processing decreased microbial contamination of eggshells. To know which species persisted during storage on washed or unwashed eggs, Enterobacteriaceae isolates were selected and identified biochemically. For each of three replications, shell eggs were purchased from a commercial processing plant, transported back to the laboratory, and stored at 4 degrees C. Once a week for 6 weeks, 12 eggs for each treatment (washed and unwashed control) were rinsed in sterile phosphate-buffered saline. A 1-ml aliquot of each sample was plated onto violet red bile glucose agar with overlay and incubated at 37 degrees C for 24 h. Following incubation, plates were observed for colonies characteristic of the family Enterobacteriaceae. A maximum of 10 isolates per positive sample were streaked for isolation before being identified to the genus or species level using commercially available biochemical strips. Although most of the isolates from the unwashed control eggs belonged to the genera Escherichia or Enterobacter, many other genera and species were identified. These included Citrobacter, Klebsiella, Kluyvera, Pantoea, Providencia, Rahnella, Salmonella, Serratia, and Yersinia. Non-Enterobacteriaceae also recovered from the unwashed egg samples included Xanthomonas and Flavimonas. Very few washed egg samples were contaminated with any of these bacteria. These data provide useful information on the effectiveness of processing in removing microorganisms from commercial shell eggs.

  9. Further development of the cleanable steel HEPA filter, cost/benefit analysis, and comparison with competing technologies

    SciTech Connect

    Bergman, W.; Lopez, R.; Wilson, K.

    1997-08-01

    We have made further progress in developing a cleanable steel fiber HEPA filter. We fabricated a pleated cylindrical cartridge using commercially available steel fiber media that is made with 1 {mu}m stainless steel fibers and sintered into a sheet form. Test results at the Department of Energy (DOE) Filter Test Station at Oak Ridge show the prototype filter cartridge has 99.99% efficiency for 0.3 {mu}m dioctyl phthalate (DOP) aerosols and a pressure drop of 1.5 inches. Filter loading and cleaning tests using AC Fine dust showed the filter could be repeatedly cleaned using reverse air pulses. Our analysis of commercially optimized filters suggest that cleanable steel HEPA filters need to be made from steel fibers less than 1{mu}m, and preferably 0.5 {mu}m, to meet the standard HEPA filter requirements in production units. We have demonstrated that 0.5 {mu}m steel fibers can be produced using the fiber bundling and drawing process. The 0.5 {mu}m steel fibers are then sintered into small filter samples and tested for efficiency and pressure drop. Test results on the sample showed a penetration of 0.0015 % at 0.3 {mu}m and a pressure drop of 1.15 inches at 6.9 ft/min (3.5 cm/s) velocity. Based on these results, steel fiber media can easily meet the requirements of 0.03 % penetration and 1.0 inch of pressure drop by using less fibers in the media. A cost analysis of the cleanable steel HEPA filter shows that, although the steel HEPA filter costs much more than the standard glass fiber HEPA filter, it has the potential to be very cost effective because of the high disposal costs of contaminated HEPA filters. We estimate that the steel HEPA filter will save an average of $16,000 over its 30 year life. The additional savings from the clean-up costs resulting from ruptured glass HEPA filters during accidents was not included but makes the steel HEPA filter even more cost effective. 33 refs., 28 figs., 1 tab.

  10. Increased hepatic functionality of the human hepatoma cell line HepaRG cultured in the AMC bioreactor.

    PubMed

    Nibourg, Geert A A; Hoekstra, Ruurdtje; van der Hoeven, Tessa V; Ackermans, Mariëtte T; Hakvoort, Theodorus B M; van Gulik, Thomas M; Chamuleau, Robert A F M

    2013-08-01

    The clinical application of a bioartificial liver (BAL) depends on the availability of a human cell source with high hepatic functionality, such as the human hepatoma cell line HepaRG. This cell line has demonstrated high hepatic functionality, but the effect of BAL culture on its functionality in time is not known. Therefore, we studied the characteristics of the HepaRG-AMC-BAL over time, and compared the functionality of the HepaRG-AMC-BAL with monolayer cultures of HepaRG cells, normalized for protein (bioactive mass) and DNA (cell number). Histological analysis of 14-day-old BALs demonstrated functional heterogeneity similar to that of monolayer cultures. Hepatic functionality of the HepaRG-AMC-BALs increased during 2-3 weeks of culture. The majority of the measured protein-normalized hepatic functions were already higher in day 14 BAL cultures compared to monolayer cultures, including ammonia elimination (3.2-fold), urea production (1.5-fold), conversion of (15)N-ammonia into (15)N-urea (1.4-fold), and cytochrome P450 3A4 activity (7.9-fold). Lactate production in monolayer cultures switched into lactate consumption in the BAL cultures, a hallmark of primary hepatocytes. When normalized for DNA, only cytochrome P450 3A4 activity was 2.5-fold higher in the BAL cultures compared to monolayer cultures and lactate production switched to consumption, whereas urea production and (15)N-urea production were 1.5- to 2-fold lower. The different outcomes for protein and DNA normalized functions probably relate to a smaller cell volume of HepaRG cells when cultured in the AMC-BAL. Cell damage was 4-fold lower in day 14 BAL cultures compared to monolayer cultures. Transcript levels of cytochrome P450 1A2, 2B6, 3A4 and 3A7 genes and of regulatory genes hepatic nuclear factor 4α and pregnane X receptor increased in time in BAL cultures and reached higher levels than in monolayer cultures. Lastly, metabolism of amino acids, particularly the alanine consumption and ornithine

  11. Short communication: Automatic washing of hooves can help control digital dermatitis in dairy cows.

    PubMed

    Thomsen, Peter T; Ersbøll, Annette Kjær; Sørensen, Jan Tind

    2012-12-01

    The objectives of this study were to develop and test a system for automatic washing of the hooves of dairy cows and to evaluate the effect of frequent automatic washing on the prevalence of digital dermatitis (DD). An automatic hoof washer was developed in an experimental dairy herd and tested in 6 commercial dairy herds in 2 experiments (1 and 2). In the experimental herd, automatic hoof washing resulted in cleaner hooves. In experiments 1 and 2, cows were washed after each milking on the left side only, leaving the right side unwashed as a within-cow control. In experiment 1, hooves were washed with a water and 0.4% soap solution. In experiment 2, hooves were washed with water only. In each experiment, DD was scored in a hoof-trimming chute approximately 60 d after the start of hoof washing. Data were analyzed using a generalized linear mixed model. The outcome was the DD status of each leg (DD positive or DD negative). Herd and cow within herd were included as random effects, and treatment (washing or control) was included as a fixed effect. The statistical analyses showed that the odds ratio of having DD was 1.48 in the control leg compared with the washed leg in experiment 1. In experiment 2, the odds ratio of having DD was 1.27 in the control leg compared with the washed leg. We concluded that automatic washing of hooves with water and soap can help decrease the prevalence of DD in commercial dairy herds.

  12. 49 CFR 230.60 - Time of washing.

    Code of Federal Regulations, 2014 CFR

    2014-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.60 Time of washing. (a) Frequency of washing. All boilers shall thoroughly be washed... inspection. The date of the boiler wash shall be noted on the FRA Form No. 1 or FRA Form No. 3. (See...

  13. 49 CFR 230.60 - Time of washing.

    Code of Federal Regulations, 2013 CFR

    2013-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.60 Time of washing. (a) Frequency of washing. All boilers shall thoroughly be washed... inspection. The date of the boiler wash shall be noted on the FRA Form No. 1 or FRA Form No. 3. (See...

  14. 49 CFR 230.60 - Time of washing.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.60 Time of washing. (a) Frequency of washing. All boilers shall thoroughly be washed... inspection. The date of the boiler wash shall be noted on the FRA Form No. 1 or FRA Form No. 3. (See...

  15. 49 CFR 230.60 - Time of washing.

    Code of Federal Regulations, 2012 CFR

    2012-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.60 Time of washing. (a) Frequency of washing. All boilers shall thoroughly be washed... inspection. The date of the boiler wash shall be noted on the FRA Form No. 1 or FRA Form No. 3. (See...

  16. 49 CFR 230.60 - Time of washing.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ..., DEPARTMENT OF TRANSPORTATION STEAM LOCOMOTIVE INSPECTION AND MAINTENANCE STANDARDS Boilers and Appurtenances Washing Boilers § 230.60 Time of washing. (a) Frequency of washing. All boilers shall thoroughly be washed... inspection. The date of the boiler wash shall be noted on the FRA Form No. 1 or FRA Form No. 3. (See...

  17. Further development of the cleanable steel HEPA filter, cost/benefit analysis, and comparison with competing technologies

    SciTech Connect

    Bergman, W.; Larsen, G.; Lopez, R.; Wilson, K.; Witherell, C.; McGregor, M.

    1997-01-01

    We have made further progress in developing a cleanable steel fiber HEPA filter. We fabricated a pleated cylindrical cartridge using commercially available steel fiber media that is made with 1 {mu}m stainless steel fibers and sintered into a sheet form. Test results at the Department of Energy (DOE) Filter Test Station at Oak Ridge show the prototype filter cartridge has 99.99% efficiency for 0.3 {mu}m dioctyl phthalate (DOP) aerosols and a pressure drop of 1.5 inches. Filter loading and cleaning tests using AC Fine dust showed the filter could be repeatedly cleaned using reverse air pulses. Our analysis of commercially optimized filters suggest that cleanable steel HEPA filters need to be made from steel fibers less than 1 {mu}m, and preferably 0.5 {mu}m, to meet the standard HEPA filter requirements in production units. We have demonstrated that 0.5 {mu}m steel fibers can be produced using the fiber bundling and drawing process. The 0.5 {mu}m steel fibers are then sintered into small filter samples and tested for efficiency and pressure drop. Test results on the sample showed a penetration of 0.0015% at 0.3 {mu}m and a pressure drop of 1.15 inches at 6.9 ft/min (3.5 cm/s) velocity. Based on these results, steel fiber media can easily meet the requirements of 0.03% penetration and 1.0 inch of pressure drop by using less fibers in the media. A cost analysis of the cleanable steel HEPA filter shows that, although the steel HEPA filter costs much more than the standard glass fiber HEPA filter, it has the potential to be very cost effective because of the high disposal costs of contaminated HEPA filters. We estimate that the steel HEPA filter will save an average of $16,000 over its 30 year life. The additional savings from the clean-up costs resulting from ruptured glass HEPA filters during accidents was not included but makes the steel HEPA filter even more cost effective. We also present the results of our evaluation of competing technologies with metallic and

  18. Comparison of cryopreserved HepaRG cells with cryopreserved human hepatocytes for prediction of clearance for 26 drugs.

    PubMed

    Zanelli, Ugo; Caradonna, Nicola Pasquale; Hallifax, David; Turlizzi, Elisa; Houston, J Brian

    2012-01-01

    Prediction of clearance in drug discovery currently relies on human primary hepatocytes, which can vary widely in drug-metabolizing enzyme activity. Potential alternative in vitro models include the HepaRG cell (from immortalized hepatoma cells), which in culture can express drug-metabolizing enzymes to an extent comparable to that of primary hepatocytes. Utility of the HepaRG cell will depend on robust performance, relative to that of primary hepatocytes, in routine high-throughput analysis. In this study, we compared intrinsic clearance (CL(int)) in the recently developed cryopreserved HepaRG cell system with CL(int) in human cryopreserved pooled hepatocytes and with CL(int) in vivo for 26 cytochrome P450 substrate drugs. There was quantitative agreement between CL(int) in HepaRG cells and human hepatocytes, which was linear throughout the range of CL(int) (1-2000 ml · min(-1) · kg(-1)) and not dependent on particular cytochrome P450 involvement. Prediction of CL(int) in HepaRG cells was on average within 2-fold of in vivo CL(int) (using the well stirred liver model), but average fold error was clearance-dependent with greater underprediction (up to at least 5-fold) for the more highly cleared drugs. Recent reporting of this phenomenon in human hepatocytes was therefore confirmed with the hepatocytes used in this study, and hence the HepaRG cell system appears to share an apparently general tendency of clearance-limited CL(int) in cell models. This study shows the cryopreserved HepaRG cell system to be quantitatively comparable to human hepatocytes for prediction of clearance of drug cytochrome P450 substrates and to represent a promising alternative in vitro tool. PMID:21998403

  19. Development assessment of wash water reclamation

    NASA Technical Reports Server (NTRS)

    Putnam, D. F.

    1976-01-01

    An analytical study assessment of state-of-the-art wash water reclamation technology is presented. It covers all non-phase-change unit operations, unit processes and subsystems currently under development by NASA. Each approach to wash water reclamation is described in detail. Performance data are given together with the projected weights and sizes of key components and subsystems. It is concluded that a simple multifiltration subsystem composed of surface-type cartridge filters, carbon adsorption and ion exchange resins is the most attractive approach for spacecraft wash water reclamation in earth orbital missions of up to 10 years in duration.

  20. TANK 7 CHARACTERIZATION AND WASHING STUDIES

    SciTech Connect

    Lambert, D.; Pareizs, J.; Click, D.

    2010-02-04

    A 3-L PUREX sludge sample from Tank 7 was characterized and then processed through a series of inhibited water washes to remove oxalate, sodium, and other soluble ions. Current plans use Tank 7 as one of the feed sources for Sludge Batch 7 (SB7). Tank 7 is high in oxalate due to the oxalic acid cleaning of the sludge heels from Tanks 5 and 6 and subsequent transfer to Tank 7. Ten decant and nine wash cycles were performed over a 47 day period at ambient temperature. Initially, seven decants and seven washes were completed based on preliminary estimates of the number of wash cycles required to remove the oxalate in the sludge. After reviewing the composition data, SRNL recommended the completion of 2 or 3 more decant/wash cycles to ensure all of the sodium oxalate had redissolved. In the first 7 washes, the slurry oxalate concentration was 12,300 mg/kg (69.6% oxalate removal compared to 96.1% removal of the other soluble ions). After all ten decants were complete, the slurry oxalate concentration was 3,080 mg/kg (89.2% oxalate removal compared to 99.0% of the other soluble ions). The rate of dissolution of oxalate increased significantly with subsequent washes until all of the sodium oxalate had been redissolved after seven decant/wash cycles. The measured oxalate concentrations agreed very well with LWO predictions for washing of the Tank 7 sample. Highlights of the analysis and washing of the Tank 7 sample include: (1) Sodium oxalate was detected in the as-received filtered solids. 95% of the oxalate was insoluble (undissolved) in the as-received slurry. (2) No sodium oxalate was detected in the post-wash filtered solids. (3) Sodium oxalate is the last soluble species that redissolves during washing with inhibited water. In order to significantly reduce the sodium oxalate concentration, the sludge must be highly washed, leaving the other soluble anions and cations (including sodium) very low in concentration. (4) The post-wash slurry had 1% of the soluble anions

  1. Wash water waste pretreatment system study

    NASA Technical Reports Server (NTRS)

    1976-01-01

    The use of real wash water had no adverse effect on soap removal when an Olive Leaf soap based system was used; 96 percent of the soap was removed using ferric chloride. Numerous chemical agents were evaluated as antifoams for synthetic wash water. Wash water surfactants used included Olive Leaf Soap, Ivory Soap, Neutrogena and Neutrogena Rain Bath Gel, Alipal CO-436, Aerosol 18, Miranol JEM, Palmeto, and Aerosol MA-80. For each type of soapy wash water evaluated, at least one antifoam capable of causing nonpersistent foam was identified. In general, the silicones and the heavy metal ions (i.e., ferric, aluminum, etc.) were the most effective antifoams. Required dosage was in the range of 50 to 200 ppm.

  2. Criteria for calculating the efficiency of deep-pleated HEPA filters with aluminum separators during and after design basis accidents

    SciTech Connect

    Bergman, W.; First, M.W.; Anderson, W.L.; Gilbert, H.; Jacox, J.W.

    1995-02-01

    The authors have reviewed the literature on the performance of high efficiency particulate air (HEPA) filters under normal and abnormal conditions to establish criteria for calculating the efficiency of HEPA filters in a DOE nonreactor nuclear facility during and after a Design Basis Accident (DBA). This study is only applicable to the standard deep-pleated HEPA filter with aluminum separators as specified in ASME N509. The literature review included the performance of new filters and parameters that may cause deterioration in the filter performance such as filter age, radiation, corrosive chemicals, seismic and rough handling, high temperature, moisture, particle clogging, high air flow and pressure pulses. The deterioration of the filter efficiency depends on the exposure parameters; in severe exposure conditions the filter will be structurally damaged and have a residual efficiency of 0%. Despite the many studies on HEPA filter performance under adverse conditions, there are large gaps and limitations in the data that introduce significant error in the estimates of HEPA filter efficiencies under DBA conditions. Because of this limitation, conservative values of filter efficiency were chosen when there was insufficient data.

  3. DEGRADED TBP SOLVENT REGENERATION TECHNOLOGY USING BUTYLAMINE AS A SOLVENT WASHING TO REDUCE SOLID SALT WASTE

    SciTech Connect

    Asakura, T.; Itoh, Y.; Hotoku, S.; Morita, Y.; Uchiyama, G.

    2003-02-27

    Normal butylamine compounds are studied as salt-free wash reagents for degraded solvent used in PUREX process in spent fuel reprocessing. The solvent wash tests were carried out with two types of butylamine compounds, n-butylamine oxalate and n-butylamine bicarbonate, by counter-current mode using a small size mixer-settler composed of two 4-stage wash steps. Di-n-butyl phosphoric acid (HDBP), the main degradation product from TBP, was removed from real degraded solvent with decontamination factor of 2.5 {approx} 7.9. The study on electrolytic decomposition of butylamine compounds was also conducted for waste treatment.

  4. Efficacy of different washing solutions and contact times on the microbial quality and safety of fresh-cut paprika.

    PubMed

    Das, B Kumar; Kim, Ji Gang; Choi, Ji Weon

    2011-10-01

    The role of different washing solutions and contact times was investigated to determine their use as potential sanitizers for maintaining the microbial quality and food safety of fresh-cut paprika. Samples were cut into small pieces, washed for both 90 and 180 s by different washing solutions: tap water, chlorinated water (100 mg/L and pH 6.5-7), electrolyzed water (pH 7.2) and ozonized water (4 mg/L). Then, samples were packaged in 50 µm polypropylene bags and stored at 5 °C for 12 days, followed by an evaluation of the antimicrobial efficacy of the treatments. Various quality and safety parameters, such as gas composition, color, off-odor, electrical conductivity and microbial numbers, were evaluated during storage. Results revealed insignificant differences in gas composition, and no off-odor was observed in any of the samples during the storage period. However, longer contact time resulted in slightly lower hue angle value than a short one for all washing solutions. Moreover, samples washed with ozone washings showed lower electrolyte leakage than other washing solutions. Samples washed for longer contact time except those washed in ozonized water showed increased microbial numbers during storage. Hence, it has been concluded that longer contact time with ozone has positive effects, whereas the other washing solutions adversely affect the microbial quality and safety aspects of fresh-cut paprika.

  5. A Wash-Free Homogeneous Colorimetric Immunoassay Method

    PubMed Central

    Liu, Huiqiao; Rong, Pengfei; Jia, Hongwei; Yang, Jie; Dong, Bo; Dong, Qiong; Yang, Cejun; Hu, Pengzhi; Wang, Wei; Liu, Haitao; Liu, Dingbin

    2016-01-01

    Rapid and convenient biosensing platforms could be beneficial to timely diagnosis and treatment of diseases in virtually any care settings. Sandwich immunoassays, the most commonly used methods for protein detection, often rely on expensive tags such as enzyme and tedious wash and incubation procedures operated by skilled labor. In this report, we revolutionized traditional sandwich immunoassays by providing a wash-free homogeneous colorimetric immunoassay method without requirement of any separation steps. The proposed strategy was realized by controlling the growth of gold nanoparticles (AuNPs) to mediate the interparticle spacing in the protein-AuNP oligomers. We have demonstrated the successful in vitro detection of cancer biomarker in serum samples from patients with high clinical sensitivity and specificity. PMID:26722373

  6. Disinfection potential of ozone, ultraviolet-C and their combination in wash water for the fresh-cut vegetable industry.

    PubMed

    Selma, María V; Allende, Ana; López-Gálvez, Francisco; Conesa, María A; Gil, María I

    2008-09-01

    The purpose of this research was to investigate the disinfection efficacy of ozone (O(3)) and UV-C illumination (UV), and their combination (O(3)-UV) for reducing microbial flora of fresh-cut onion, escarole, carrot, and spinach wash waters collected from the industry. Furthermore, the influence of water physicochemical parameters on the decontamination efficacy and the effect of these technologies on physicochemical quality of wash water were analyzed. O(3), UV, and O(3)-UV were effective disinfection treatments on vegetable wash water, with a maximum microbial reduction of 6.6 log CFU mL(-1) after 60 min treatment with O(3)-UV. However, maximum total microbial reductions achieved by UV and O(3) treatments after 60 min were 4.0 and 5.9 log CFU mL(-1), lower than by O(3)-UV treatment. Furthermore, turbidity of wash water was reduced significantly by O(3) and O(3)-UV treatments, while UV treatment did not affect the physicochemical quality of the water. Conclusions derived from this study illustrate that O(3) and O(3)-UV are alternatives to other sanitizers used in the fresh-cut washing processes. The use of these technologies would allow less frequent changing of spent water and the use of much lower sanitizer doses. Nevertheless, in specific applications such as carrot wash water, where levels of undesirable microbial and chemical constituents are lower than other vegetable wash water, UV treatment could be an appropriate treatment considering cost-effectiveness criteria.

  7. Health hazards associated with the use of di-(2-ethylhexyl) phthalate (commonly referred to as DOP) in HEPA filter test

    SciTech Connect

    1995-01-01

    Di-(2-ethylhexyl) phthalate (DEHP), commonly referred to as di-octyl phthalate, is an important production chemical in the US. In addition to its major use as an additive in plastics, DEHP is widely used to evaluate the effectiveness of high efficiency particulate air (HEPA) filters. Historically, DEHP was also used in quantitative fit testing for respirators. Evaluations of this compound a decade ago showed that it can induce hepatocellular carcinomas in laboratory animals. Although most Department of Energy (DOE) facilities have since discontinued using DEHP in respirator fit testing, DEHP continues to be used for evaluating HEPA filters. This report summarizes available information on the toxicity, mutagenicity, carcinogenicity, and other hazards and problems posed by DEHP, specifically with reference to HEPA filter testing. Information on work practice improvements as well as the availability and suitability of DEHP substitutes are also presented. This material should assist the DOE in the safe use of this material.

  8. A Custom Robotic System for Inspecting HEPA Filters in the Payload Changeout Room at the NASA Kennedy Space Center

    NASA Technical Reports Server (NTRS)

    Spencer, James E., Jr.; Looney, Joe

    1994-01-01

    In this paper, the prime objective is to describe a custom 4-dof (degree-of-freedom) robotic arm capable of autonomously or telerobotically performing systematic HEPA filter inspection and certification in the Shuttle Launch Pad Payload Changeout Rooms (PCR's) on pads A and B at the Kennedy Space Center, Florida. This HEPA filter inspection robot (HFIR) has been designed to be easily deployable and is equipped with the necessary sensory devices, control hardware, software and man-machine interfaces needed to implement HEPA filter inspection reliably and efficiently without damaging the filters or colliding with existing PCR structures or filters. The main purpose of the HFIR is to implement an automated positioning system to move special inspection sensors in pre-defined or manual patterns for the purpose of verifying filter integrity and efficiency. This will ultimately relieve NASA Payload Operations from significant problems associated with time, cost and personnel safety, impacts realized during non-automated PCR HFIR filter certification.

  9. Intervention study of airborne fungal spora in homes with portable HEPA filtration units.

    PubMed

    Cheong, C D; Neumeister-Kemp, H G; Dingle, P W; Hardy, G St J

    2004-11-01

    The concentrations and composition of airborne fungal spores in homes fitted with portable HEPA filtration units were examined to provide information to evaluate the importance of varying levels of fungal spores in residential environments in Perth, Australia. A novel method for simulating activity/impaction on carpeted environments was also investigated. Reductions in fungal (35%) and particulate (38%) levels were achieved in the air filter homes. Penicillium, Cladosporium and yeasts were the most common and widespread fungi recovered indoors and outdoors. Fungal range decreased over the study period but this could be due to an overall reduced dissemination of spores (less spores in the air). PMID:15536499

  10. Comparative evaluation of N-acetylcysteine and N-acetylcysteineamide in acetaminophen-induced hepatotoxicity in human hepatoma HepaRG cells

    PubMed Central

    Tobwala, Shakila; Khayyat, Ahdab; Fan, Weili

    2015-01-01

    Acetaminophen (N-acetyl-p-aminophenol, APAP) is one of the most widely used over-the-counter antipyretic analgesic medications. Despite being safe at therapeutic doses, an accidental or intentional overdose can result in severe hepatotoxicity; a leading cause of drug-induced liver failure in the U.S. Depletion of glutathione (GSH) is implicated as an initiating event in APAP-induced toxicity. N-acetylcysteine (NAC), a GSH precursor, is the only currently approved antidote for an APAP overdose. Unfortunately, fairly high doses and longer treatment times are required due to its poor bioavailability. In addition, oral and intravenous administration of NAC in a hospital setting are laborious and costly. Therefore, we studied the protective effects of N-acetylcysteineamide (NACA), a novel antioxidant, with higher bioavailability and compared it with NAC in APAP-induced hepatotoxicity in a human-relevant in vitro system, HepaRG. Our results indicated that exposure of HepaRG cells to APAP resulted in GSH depletion, reactive oxygen species (ROS) formation, increased lipid peroxidation, mitochondrial dysfunction (assessed by JC-1 fluorescence), and lactate dehydrogenase release. Both NAC and NACA protected against APAP-induced hepatotoxicity by restoring GSH levels, scavenging ROS, inhibiting lipid peroxidation, and preserving mitochondrial membrane potential. However, NACA was better than NAC at combating oxidative stress and protecting against APAP-induced damage. The higher efficiency of NACA in protecting cells against APAP-induced toxicity suggests that NACA can be developed into a promising therapeutic option for treatment of an APAP overdose. PMID:25245075

  11. Criteria for calculating the efficiency of deep-pleated HEPA filters with aluminum separators during and after design basis accidents

    SciTech Connect

    Bergman, W.; First, M.W.; Anderson, W.L.

    1995-02-01

    We have reviewed the literature on the performance of HEPA filters under normal and abnormal conditions to establish criteria for calculating the efficiency of HEPA filters in a DOE nonreactor nuclear facility during and after a Design Basis Accident (DBA). This study is only applicable to the standard deep-pleated HEPA filter with aluminum separators as specified in ASME N509[1]. Other HEPA filter designs such as the mini-pleat and separatorless filters are not included in this study. The literature review included the performance of new filters and parameters that may cause deterioration in the filter performance such as filter age, radiation, corrosive chemicals, seismic and rough handling, high temperature, moisture, particle clogging, high air flow and pressure pulses. The deterioration of the filter efficiency depends on the exposure parameters; in severe exposure conditions the filter will be damaged and have a residual efficiency of 0%. There are large gaps and limitations in the data that introduce significant error in the estimates of HEPA filter efficiencies under DBA conditions. Because of this limitation, conservative values of filter efficiency were chosen. The estimation of the efficiency of the HEPA filters under DBA conditions involves three steps: (1) The filter pressure drop and environmental parameters are determined during and after the DBA, (2) Comparing the filter pressure drop to a set of threshold values above which the filter is damaged. There is a different threshold value for each combination of environmental parameters, and (3) Determining the filter efficiency. If the filter pressure drop is greater than the threshold value, the filter is damaged and is assigned 0% efficiency. If the pressure drop is less, then the filter is not damaged and the efficiency is determined from literature values of the efficiency at the environmental conditions.

  12. The Potential of Wash-and-Dry Toilets to Improve the Toileting Experience for Nursing Home Residents

    ERIC Educational Resources Information Center

    Cohen-Mansfield, Jiska; Biddison, James R.

    2005-01-01

    Purpose: We investigated the feasibility of using a "wash-and-dry" toilet in the nursing home. Design and Methods: We used a controlled comparison baseline-versus-treatment design with 22 female nursing home residents aged 75 and older living in a 562-bed, not-for-profit nursing home facility in Maryland. The Luscence Luxury Lavage wash-and-dry…

  13. Understanding road surface pollutant wash-off and underlying physical processes using simulated rainfall.

    PubMed

    Egodawatta, Prasanna; Goonetilleke, Ashantha

    2008-01-01

    Pollutant wash-off is one of the key pollutant processes that detailed knowledge is required in order to develop successful treatment design strategies for urban stormwater. Unfortunately, current knowledge relating to pollutant wash-off is limited. This paper presents the outcomes of a detailed investigation into pollutant wash-off on residential road surfaces. The investigations consisted of research methodologies formulated to overcome the physical constraints due to the heterogeneity of urban paved surfaces and the dependency on naturally occurring rainfall. This entailed the use of small road surface plots and artificially simulated rainfall. Road surfaces were selected due to its critical importance as an urban stormwater pollutant source. The study results showed that the influence of initially available pollutants on the wash-off process was limited. Furthermore, pollutant wash-off from road surfaces can be replicated using an exponential equation. However, the typical version of the exponential wash-off equation needs to be modified by introducing a non dimensional factor referred to as 'capacity factor' CF. Three rainfall intensity ranges were identified where the variation of CF can be defined. Furthermore, it was found that particulate density rather than size is the critical parameter that influences the process of pollutant wash-off.

  14. Methoxychlor suppresses the 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD)-inducible CYP1A1 expression in murine Hepa-1c1c7 cells.

    PubMed

    Han, Eun Hee; Jeong, Tae Cheon; Jeong, Hye Gwang

    2007-08-01

    Methoxychlor (MXC) is a pesticide that was developed as a replacement for dichlorodiphenyltrichloroethane (DDT). The influence of MXC on CYP1A1 expression or the functions of mouse hepatoma Hepa-1clc7 remain unclear. Cultured Hepa-1c1c7 cells were treated with MXC with or without 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) to assess the role of MXC on CYP1A1 expression. MXC alone did not affect CYP1A1-specific 7-ethoxyresorufin O-deethylase (EROD) activity. In contrast, TCDD-inducible EROD activities were markedly reduced upon concomitant treatment with TCDD and MXC in a concentration-dependent manner. Treatment with ICI 182.780, an estrogen-receptor antagonist, did not affect the suppressive effects of MXC on TCDD-inducible EROD activity. TCDD-inducible CYP1A1 mRNA levels were markedly suppressed upon treatment with TCDD and MXC, and this is consistent with their effects on EROD activity. A transient transfection assay using dioxin-response element (DRE)-linked luciferase and an electrophoretic mobility shift assay revealed that MXC reduced the transformation of the aryl hydrocarbons (Ah) receptor to a form capable of specifically binding to the DRE sequence in the promoter region of the CYP1A1 gene. These results suggest that the downregulation of CYP1A1 gene expression by MXC in Hepa-1c1c7 cells might be an antagonism of the DRE binding potential of the nuclear Ah receptor but is not mediated through the estradiol receptor.

  15. In-place HEPA (high efficiency, particulate air) filter testing at Hanford: Operating experiences, calibrations, and lessons learned

    SciTech Connect

    Flores, D.S.; Decelis, D.G.

    1989-10-01

    High Efficiency, Particulate Air (HEPA) Filters provide a minimum of 99.97% removal efficiency for particles greater than or equal to .3 microns in diameter. Each HEPA filter installation at Hanford is, at specified intervals, functionally tested for leaks. The test procedure involves a dioctylphthalate (DOP) smoke generator and a calibrated airborne particle detector. The DOP generator produces smoke of a known quantitative particle size distribution upstream of the filter. The airborne particle detector is first placed upstream, and then downstream of the filter to determine percent penetration. The smoke generator is characterized using a calibrated laser spectrometer, and the particle detector is calibrated using a calibrated picoammeter. 2 refs., 4 figs.

  16. Hand washing promotion for preventing diarrhoea

    PubMed Central

    Ejemot-Nwadiaro, Regina I; Ehiri, John E; Arikpo, Dachi; Meremikwu, Martin M; Critchley, Julia A

    2015-01-01

    Background Diarrhoea accounts for 1.8 million deaths in children in low- and middle-income countries (LMICs). One of the identified strategies to prevent diarrhoea is hand washing. Objectives To assess the effects of hand washing promotion interventions on diarrhoeal episodes in children and adults. Search methods We searched the Cochrane Infectious Diseases Group Specialized Register (27 May 2015); CENTRAL (published in the Cochrane Library 2015, Issue 5); MEDLINE (1966 to 27 May 2015); EMBASE (1974 to 27 May 2015); LILACS (1982 to 27 May 2015); PsycINFO (1967 to 27 May 2015); Science Citation Index and Social Science Citation Index (1981 to 27 May 2015); ERIC (1966 to 27 May 2015); SPECTR (2000 to 27 May 2015); Bibliomap (1990 to 27 May 2015); RoRe, The Grey Literature (2002 to 27 May 2015); World Health Organization (WHO) International Clinical Trial Registry Platform (ICTRP), metaRegister of Controlled Trials (mRCT), and reference lists of articles up to 27 May 2015. We also contacted researchers and organizations in the field. Selection criteria Individually randomized controlled trials (RCTs) and cluster-RCTs that compared the effects of hand washing interventions on diarrhoea episodes in children and adults with no intervention. Data collection and analysis Three review authors independently assessed trial eligibility, extracted data, and assessed risk of bias. We stratified the analyses for child day-care centres or schools, community, and hospital-based settings. Where appropriate, incidence rate ratios (IRR) were pooled using the generic inverse variance method and random-effects model with 95% confidence intervals (CIs). We used the GRADE approach to assess the quality of evidence. Main results We included 22 RCTs: 12 trials from child day-care centres or schools in mainly high-income countries (54,006 participants), nine community-based trials in LMICs (15,303 participants), and one hospital-based trial among people with acquired immune deficiency

  17. 21 CFR 133.137 - Washed curd cheese for manufacturing.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 2 2014-04-01 2014-04-01 false Washed curd cheese for manufacturing. 133.137... Standardized Cheese and Related Products § 133.137 Washed curd cheese for manufacturing. Washed curd cheese for manufacturing conforms to the definition and standard of identity prescribed for washed curd cheese by §...

  18. 21 CFR 133.137 - Washed curd cheese for manufacturing.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Washed curd cheese for manufacturing. 133.137... Standardized Cheese and Related Products § 133.137 Washed curd cheese for manufacturing. Washed curd cheese for manufacturing conforms to the definition and standard of identity prescribed for washed curd cheese by §...

  19. 21 CFR 133.137 - Washed curd cheese for manufacturing.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 2 2011-04-01 2011-04-01 false Washed curd cheese for manufacturing. 133.137... Standardized Cheese and Related Products § 133.137 Washed curd cheese for manufacturing. Washed curd cheese for manufacturing conforms to the definition and standard of identity prescribed for washed curd cheese by §...

  20. 21 CFR 133.137 - Washed curd cheese for manufacturing.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 2 2012-04-01 2012-04-01 false Washed curd cheese for manufacturing. 133.137... Standardized Cheese and Related Products § 133.137 Washed curd cheese for manufacturing. Washed curd cheese for manufacturing conforms to the definition and standard of identity prescribed for washed curd cheese by §...

  1. 21 CFR 133.137 - Washed curd cheese for manufacturing.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 2 2013-04-01 2013-04-01 false Washed curd cheese for manufacturing. 133.137... Standardized Cheese and Related Products § 133.137 Washed curd cheese for manufacturing. Washed curd cheese for manufacturing conforms to the definition and standard of identity prescribed for washed curd cheese by §...

  2. 30 CFR 1206.260 - Allocation of washed coal.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  3. 30 CFR 1206.260 - Allocation of washed coal.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  4. 30 CFR 1206.459 - Allocation of washed coal.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  5. 30 CFR 1206.260 - Allocation of washed coal.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Allocation of washed coal. 1206.260 Section... RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  6. 30 CFR 1206.459 - Allocation of washed coal.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 30 Mineral Resources 3 2013-07-01 2013-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  7. 30 CFR 1206.459 - Allocation of washed coal.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Allocation of washed coal. 1206.459 Section... INTERIOR Natural Resources Revenue PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it...

  8. 30 CFR 1206.260 - Allocation of washed coal.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Allocation of washed coal. 1206.260 Section... INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it...

  9. 30 CFR 206.459 - Allocation of washed coal.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Allocation of washed coal. 206.459 Section 206... MANAGEMENT PRODUCT VALUATION Indian Coal § 206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When the...

  10. 30 CFR 1206.459 - Allocation of washed coal.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Allocation of washed coal. 1206.459 Section... RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.459 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b)...

  11. 30 CFR 206.260 - Allocation of washed coal.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Allocation of washed coal. 206.260 Section 206... MANAGEMENT PRODUCT VALUATION Federal Coal § 206.260 Allocation of washed coal. (a) When coal is subjected to washing, the washed coal must be allocated to the leases from which it was extracted. (b) When the...

  12. Soil washing enhancement with solid sorbents

    SciTech Connect

    El-Shoubary, Y.M.; Woodmansee, D.E.

    1996-12-31

    Soil washing is a dynamic, physical process that remediates contaminated soil through two mechanisms: particle size separation and transfer of the contaminant into the (mostly) liquid stream. The performance of different sorbents and additives to remove motor oil from sea sand was tested. Hydrocyclone, attrition scrubber, and froth flotation equipment were used for the decontamination study. Sorbents and additives were mixed with soils in the attrition scrubber prior to flotation. Sorbents used were granular activated carbon, powder activated carbon, and rubber tires. Chemical additives used were calcium hydroxide, sodium carbonate, Alconox{reg_sign}, Triton{reg_sign} X-100 and Triton{reg_sign} X-114. When a froth flotation run was performed using no additive, washed soils {open_quotes}tails{close_quotes} contained 4000 ppm of total oil and grease (TOG). However, when carbon or rubber (6% by weight) was added to the contaminated soils the washed soils {open_quotes}tails{close_quotes} contained 4000 ppm of total oil and grease (TOG). The addition of sodium carbonate or calcium hydroxide (6% by weight) had same effects as sorbents. In both cases washed soil {open_quotes}tails{close_quotes} contained total oil and grease of less than 1000 ppm. The use of these non-hazardous additives or sorbent can enhance the soil washing process and consequently saves on time (residence time in equipment design) required to achieve the target clean up levels. 18 refs., 12 figs.

  13. Wash-out of ambient air contaminations for breath measurements.

    PubMed

    Maurer, F; Wolf, A; Fink, T; Rittershofer, B; Heim, N; Volk, T; Baumbach, J I; Kreuer, S

    2014-06-01

    In breath analysis, ambient air contaminations are ubiquitous and difficult to eliminate. This study was designed to investigate the reduction of ambient air background by a lung wash-out with synthetic air. The reduction of the initial ambient air volatile organic compound (VOC) intensity was investigated in the breath of 20 volunteers inhaling synthetic air via a sealed full face mask in comparison to inhaling ambient air. Over a period of 30 minutes, breath analysis was conducted using ion mobility spectrometry coupled to a multi-capillary column. A total of 68 VOCs were identified for inhaling ambient air or inhaling synthetic air. By treatment with synthetic air, 39 VOCs decreased in intensity, whereas 29 increased in comparison to inhaling ambient air. In total, seven VOCs were significantly reduced (P-value < 0.05). A complete wash-out of VOCs in this setting was not observed, whereby a statistically significant reduction up to 65% as for terpinolene was achieved. Our setting successfully demonstrated a reduction of ambient air contaminations from the airways by a lung wash-out with synthetic air.

  14. Preliminary studies to determine the shelf life of HEPA filters. Revision 1

    SciTech Connect

    Gilbert, H.; Fretthold, J.K.; Rainer, F.; Bergman, W.; Beason, D.

    1995-02-01

    We have completed a preliminary study using filter media tests and filter qualification tests to investigate the effect of shelf-life on HEPA filter performance. Our media studies showed that the tensile strength decreased with age, but the data were not sufficient to establish a shelf-life. Thermogravimetric analyses demonstrated that one manufacturer had media with low tensile strength due to insufficient binder. The filter qualification tests (heated air and overpressure) conducted on different aged filters showed that filter age is not the primary factor affecting filter performance; materials and the construction design have a greater effect. An unexpected finding of our study was that sub-standard HEPA filters have been installed in DOE facilities despite existing regulations and filter qualification tests. We found that the filter with low tensile strength failed the overpressure test. The same filter had passed the heated air test, but left the filter so structurally weak, it was prone to blow-out. We recommend that DOE initiate a filter qualification program to prevent this occurrence.

  15. Replacement of HEPA Filters at the LANL CMR Facility : risk reduced by comprehensive waste characterization

    SciTech Connect

    Corpion, J. C.

    2002-01-01

    In March 2001, the Los Alamos National Laboratory (LANL) completed the replacement of 720 radioactively contaminated HEPA filters for $5.7M. This project was completed five months ahead of schedule and $6.0M under budget with no worker injuries or contaminations. Numerous health and safety, environmental, and waste disposal problems were overcome, including having to perform work in a radioactively contaminated work environment, that was also contaminated with perchlorates (potential explosive). High waste disposal costs were also an issue. A project risk analysis and government cost estimate determined that the cost of performing the work would be $11.8M. To reduce risk, a $1.2M comprehensive condition assessment was performed to determine the degree of toxic and radioactive contamination trapped on the HEPA filters; and to determine whether explosive concentrations of perchlorates were present. Workers from LANL and personnel from Waldheim International of Knoxville, TN collected hundreds of samples wearing personnel protective gear against radioactive, toxic, and explosive hazards. LANL also funded research at the New Mexico Institute of Mining and Technology to determine the explosivity of perchlorates. The data acquired from the condition assessment showed that toxic metals, toxic organic compounds, and explosive concentrations of perchlorates were absent. The data also showed that the extent of actinide metal contamination was less than expected, reducing the potential of transuranic waste generation by 50%. Consequently, $4.2M in cost savings and $1.8M in risk reduction were realized by increased worker productivity and waste segregation.

  16. Replacement of HEPA Filters at the LANL CMR Facility: Risks Reduced by Comprehensive Waste Characterization

    SciTech Connect

    Corpion, J.; Barr, A.; Martinez, P.; Bader, M.

    2002-02-28

    In March 2001, the Los Alamos National Laboratory (LANL) completed the replacement of 720 radioactively contaminated HEPA filters for $5.7M. This project was completed five months ahead of schedule and $6.0M under budget with no worker injuries or contaminations. Numerous health and safety, environmental, and waste disposal problems were overcome, including having to perform work in a radioactively contaminated work environment, that was also contaminated with perchlorates (potential explosive). High waste disposal costs were also an issue. A project risk analysis and government cost estimate determined that the cost of performing the work would be $11.8M. To reduce risk, a $1.2M comprehensive condition assessment was performed to determine the degree of toxic and radioactive contamination trapped on the HEPA filters; and to determine whether explosive concentrations of perchlorates were present. Workers from LANL and personnel from Waldheim International of Knoxville, TN collected hundreds of samples wearing personnel protective gear against radioactive, toxic, and explosive hazards. LANL also funded research at the New Mexico Institute of Mining and Technology to determine the explosivity of perchlorates. The data acquired from the condition assessment showed that toxic metals, toxic organic compounds, and explosive concentrations of perchlorates were absent. The data also showed that the extent of actinide metal contamination was less than expected, reducing the potential of transuranic waste generation by 50%. Consequently, $4.2M in cost savings and $1.8M in risk reduction were realized by increased worker productivity and waste segregation.

  17. Testing chemical carcinogenicity by using a transcriptomics HepaRG-based model?

    PubMed Central

    Doktorova, T. Y.; Yildirimman, Reha; Ceelen, Liesbeth; Vilardell, Mireia; Vanhaecke, Tamara; Vinken, Mathieu; Ates, Gamze; Heymans, Anja; Gmuender, Hans; Bort, Roque; Corvi, Raffaella; Phrakonkham, Pascal; Li, Ruoya; Mouchet, Nicolas; Chesne, Christophe; van Delft, Joost; Kleinjans, Jos; Castell, Jose; Herwig, Ralf; Rogiers, Vera

    2014-01-01

    The EU FP6 project carcinoGENOMICS explored the combination of toxicogenomics and in vitro cell culture models for identifying organotypical genotoxic- and non-genotoxic carcinogen-specific gene signatures. Here the performance of its gene classifier, derived from exposure of metabolically competent human HepaRG cells to prototypical non-carcinogens (10 compounds) and hepatocarcinogens (20 compounds), is reported. Analysis of the data at the gene and the pathway level by using independent biostatistical approaches showed a distinct separation of genotoxic from non-genotoxic hepatocarcinogens and non-carcinogens (up to 88 % correct prediction). The most characteristic pathway responding to genotoxic exposure was DNA damage. Interlaboratory reproducibility was assessed by blindly testing of three compounds, from the set of 30 compounds, by three independent laboratories. Subsequent classification of these compounds resulted in correct prediction of the genotoxicants. As expected, results on the non-genotoxic carcinogens and the non-carcinogens were less predictive. In conclusion, the combination of transcriptomics with the HepaRG in vitro cell model provides a potential weight of evidence approach for the evaluation of the genotoxic potential of chemical substances. PMID:26417288

  18. 3D spheroid cultures improve the metabolic gene expression profiles of HepaRG cells

    PubMed Central

    Takahashi, Yu; Hori, Yuji; Yamamoto, Tomohisa; Urashima, Toshiki; Ohara, Yasunori; Tanaka, Hideo

    2015-01-01

    3D (three-dimensional) cultures are considered to be an effective method for toxicological studies; however, little evidence has been reported whether 3D cultures have an impact on hepatocellular physiology regarding lipid or glucose metabolism. In the present study, we conducted physiological characterization of hepatoma cell lines HepG2 and HepaRG cells cultured in 3D conditions using a hanging drop method to verify the effect of culture environment on cellular responses. Apo (Apolipoprotein)B as well as albumin secretion was augmented by 3D cultures. Expression of genes related to not only drug, but also glucose and lipid metabolism were significantly enhanced in 3D cultured HepaRG spheroids. Furthermore, mRNA levels of CYP (cytochrome P450) enzymes following exposure to corresponding inducers increased under the 3D condition. These data suggest that this simple 3D culture system without any special biomaterials can improve liver-specific characteristics including lipid metabolism. Considering that the system enables high-throughput assay, it may become a powerful tool for compound screening concerning hepatocellular responses in order to identify potential drugs. PMID:26182370

  19. Evaluating the efficacy of playground washing to reduce environmental metal exposures.

    PubMed

    Taylor, Mark Patrick; Zahran, Sammy; Kristensen, Louise; Rouillon, Marek

    2015-07-01

    Washing and wet mopping is often advocated as a remedial treatment to limit exposure to lead dust. Here, surface and pre- and post-play wipes were measured to ascertain dust metal exposures (arsenic, cadmium, copper, lead and zinc) following play routines at four playgrounds in the smelter city of Port Pirie, South Australia, which are washed regularly. Although post-play hand wipe metals were 55.9% (95% CI: -0.78, -0.34) lower on wash days, loadings increased ∼5.1% (95% CI: 1.2, 11.7) per hour after washing. Despite washing, post-play hand lead exceeded a conservative value of 800 μg/m(2) within 24 h or sooner, with loadings increasing in proximity to the smelter. Post-play lead loadings were always >1000 μg/m(2) at the playground closest to smelter. Playground washing results in short-lived exposure reduction and effective treatment requires elimination of smelter emissions. PMID:25818090

  20. Use of the HepaRG Cell Line to Assess Potential Human Hepatotoxicity of ToxCast™ Chemicals

    EPA Science Inventory

    The HepaRG cell line is a promising model system for predicting human hepatotoxicity in part because of the greater capacity to metabolize chemicals than other cell models. We hypothesized that this cell line would be a relevant model for toxicity testing of industrial chemicals....

  1. Evaluation of Alternative Control for Prevention and or Mitigation of HEPA Filter Failure Accidents at Tank Farm Facilities

    SciTech Connect

    GUSTAVSON, R.D.

    2000-01-28

    This study evaluates the adequacy and benefit of use of HEPA filter differential pressure limiting setpoints to initiate exhauster shut down as an alternative safety control for postulated accidents that might result in filtration failure and subsequent unfiltered release from Tank Farm primary tank ventilators.

  2. Evaluation of genotoxicity using automated detection of γH2AX in metabolically competent HepaRG cells.

    PubMed

    Quesnot, Nicolas; Rondel, Karine; Audebert, Marc; Martinais, Sophie; Glaise, Denise; Morel, Fabrice; Loyer, Pascal; Robin, Marie-Anne

    2016-01-01

    The in situ detection of γH2AX was recently reported to be a promising biomarker of genotoxicity. In addition, the human HepaRG hepatoma cells appear to be relevant for investigating hepatic genotoxicity since they express most of drug metabolizing enzymes and a wild type p53. The aim of this study was to determine whether the automated in situ detection of γH2AX positive HepaRG cells could be relevant for evaluation of genotoxicity after single or long-term repeated in vitro exposure compared to micronucleus assay. Metabolically competent HepaRG cells were treated daily with environmental contaminants and genotoxicity was evaluated after 1, 7 and 14 days. Using these cells, we confirmed the genotoxicity of aflatoxin B1 and benzo(a)pyrene and demonstrated that dimethylbenzanthracene, fipronil and endosulfan previously found genotoxic with comet or micronucleus assays also induced γH2AX phosphorylation. Furthermore, we showed that fluoranthene and bisphenol A induced γH2AX while no effect had been previously reported in HepG2 cells. In addition, induction of γH2AX was observed with some compounds only after 7 days, highlighting the importance of studying long-term effects of low doses of contaminants. Together, our data demonstrate that automated γH2AX detection in metabolically competent HepaRG cells is a suitable high-through put genotoxicity screening assay.

  3. Comparison of human hepatoma HepaRG cells with human and rat hepatocytes in uptake transport assays in order to predict a risk of drug induced hepatotoxicity.

    PubMed

    Szabo, Monika; Veres, Zsuzsa; Baranyai, Zsolt; Jakab, Ferenc; Jemnitz, Katalin

    2013-01-01

    Human hepatocytes are the gold standard for toxicological studies but they have several drawbacks, like scarce availability, high inter-individual variability, a short lifetime, which limits their applicability. The aim of our investigations was to determine, whether HepaRG cells could replace human hepatocytes in uptake experiments for toxicity studies. HepaRG is a hepatoma cell line with most hepatic functions, including a considerable expression of uptake transporters in contrast to other hepatic immortalized cell lines. We compared the effect of cholestatic drugs (bosentan, cyclosporinA, troglitazone,) and bromosulfophthalein on the uptake of taurocholate and estrone-3-sulfate in human and rat hepatocytes and HepaRG cells. The substrate uptake was significantly slower in HepaRG cells than in human hepatocytes, still, in the presence of drugs we observed a concentration dependent decrease in uptake. In all cell types, the culture time had a significant impact not only on the uptake process but on the inhibitory effect of drugs too. The most significant drug effect was measured at 4 h after seeding. Our report is among the first concerning interactions of the uptake transporters in the HepaRG, at the functional level. Results of the present study clearly show that concerning the inhibition of taurocholate uptake by cholestatic drugs, HepaRG cells are closer to human hepatocytes than rat hepatocytes. In conclusion, we demonstrated that HepaRG cells may provide a suitable tool for hepatic uptake studies. PMID:23516635

  4. What Happens at a Car Wash?

    ERIC Educational Resources Information Center

    Gallick, Barbara; Lee, Lisa

    2010-01-01

    A class of 3- to 5-year-old children in a child care center in the midwestern United States chose to study a car wash as a group project. This article discusses how the project evolved, describes the three phases of the project, and provides the teachers' reflections on the project. Photos taken during the project and children's sketches are…

  5. An Alternative Antimicrobial Commercial Egg Washing Procedure

    Technology Transfer Automated Retrieval System (TEKTRAN)

    Presently, commercial eggs are washed with water containing an alkali detergent at approximately pH 11 followed by a chlorine rinse. At this pH, it is likely that there is little, if any, free chlorine in the final rinse to act as an antimicrobial against pathogens like Salmonella. Using a chlorine ...

  6. SOIL-WASHING TECHNOLOGY AND PRACTICE

    EPA Science Inventory

    Soil washing in the United States has been studied and evaluated with increasing thoroughness during the last 15 to 20 years. It is now entering a phase of actual use and acceptance as its applicability and economics become clearer. This paper reviews the principles behind soil...

  7. DEMONSTRATION BULLETIN: BIOGENESIS SOIL WASHING TECHNOLOGY - BIOGENESIS

    EPA Science Inventory

    The BioGenesisSM soil washing technology was developed by BioGenesis Enterprises, Inc. to remove organic compounds from soil. The technology uses a proprietary solution (BioGenesisSM cleaner) to transfer organic compounds from the soil matrix to a liquid phase. BioGenesis claims...

  8. EVALUATION OF THE BIOGENESIS SOIL WASHING TECHNOLOGY

    EPA Science Inventory

    The BioGenesis Enterprises, Inc. (BioGenesis) soil washing technology was demonstrated as part of the US Environmental Protection Agency's (EPA) Superfund Innovative Technology Evaluation (SITE) program in November 1992. The demonstration was conducted over three days at a petrol...

  9. Prototype wash water renovation system integration with government-furnished wash fixture

    NASA Technical Reports Server (NTRS)

    1984-01-01

    The requirements of a significant quantity of proposed life sciences experiments in Shuttle payloads for available wash water to support cleansing operations has provided the incentive to develop a technique for wash water renovation. A prototype wash water waste renovation system which has the capability to process the waste water and return it to a state adequate for reuse in a typical cleansing fixture designed to support life science experiments was investigated. The resulting technology is to support other developments efforts pertaining to water reclamation by serving as a pretreatment step for subsequent reclamation procedures.

  10. Exposure assessment of four pharmaceutical powders based on dustiness and evaluation of damaged HEPA filters.

    PubMed

    Levin, Marcus; Koponen, Ismo K; Jensen, Keld A

    2014-01-01

    In this study, we show the different dustiness characteristics of four molecular pharmaceutical powder candidates and evaluate the performance of HEPA filters damaged with three different pinhole sizes and exposed to dust using real industrial powders in a miniaturized EN15051 rotating drum dustiness tester. We then demonstrate the potential use of such data using first-order exposure modeling to assess the potential worker exposure and transmission of active powder ingredients into ventilation systems. The four powders had highly variable inhalable dustiness indices (1,036 - 14,501 mg/kg). Dust particle size-distributions were characterized by three peaks; the first occurred around 60-80 nm, the second around 250 nm, and the third at 2-3 μm. The second and third peaks are often observed in dustiness test studies, but peaks in the 60-80 nm range have not been previously reported. Exposure modeling in a 5 times 20 kg powder pouring scenario, suggests that excessive dust concentrations may be reached during use of powders with the highest dustiness levels. By number, filter-damage by three pinhole sizes resulted in damage-dependent penetration of 70-80 nm-size particles, but by volume and mass the penetration is still dominated by particles larger than 100 nm. Whereas the exposure potential was evident, the potential dust concentrations in air ducts following the pouring scenario above were at pg/m(3) levels. Hence, filter penetration at these damage levels was assumed to be only critical, if the active ingredients were associated with high hazard or unique product purity is required. [Supplementary materials are available for this article. Go to the publisher's online edition of Journal of Occupational and Environmental Hygiene for the following free supplemental resource: An example of a typical particle number time-series of a complete dustiness test. It provides information on the HEPA-filter used including a scanning electron microscopy image of it. It also

  11. A Novel Glycinate-based Body Wash

    PubMed Central

    Regan, Jamie; Ananthapadmanabhan, K.P.

    2013-01-01

    Objective: To assess the properties of a novel body wash containing the mild surfactant glycinate. Design: Biochemical and clinical assays. Setting: Research laboratories and clinical sites in the United States and Canada. Participants: Women 18 to 65 years of age (cleansing efficacy); male and female subjects 26 to 63 years of age with mild or moderate dryness and erythema (leg-controlled application test); subjects 5 to 65 years of age with mild-to-moderate eczema (eczema compatibility); and women 18 to 64 years of age (home use). Measurements: Assessments across studies included colorimetric dye exclusion to assess skin damage potential (corneosurfametry), efficacy of cosmetic product removal from skin, change from baseline in visual dryness, change from baseline in Eczema Area and Severity Index, and self-perceived eczema attributes and self-reported product preference. Results: The glycinate-based cleanser demonstrated mildness to skin components when evaluated in a corneosurfametry assay. Short-term use under exaggerated wash conditions in subjects with dryness scores <3 and erythema scores <2 (both on a 0-6 scale) indicated an initial reduction in visual dryness. In subjects with eczema, normal use resulted in significant improvements (p<0.05) at Week 4 compared with baseline in skin dryness (change from baseline = −0.73), rash (−0.56), itch (−0.927), tightness (−0.585), and all eczema (−0.756). The glycinate-based body wash removed 56 percent of a long-lasting cosmetic foundation from skin compared with less than 30 percent removed by two competitive products tested. The glycinate-based body wash was preferred over a competitive mild cleansing product overall. Conclusion: The patented glycinate-containing body wash demonstrated better product mildness and patient-preferred attributes and clinical benefits. PMID:23882306

  12. Microbiologic effectiveness of hand washing with soap in an urban squatter settlement, Karachi, Pakistan.

    PubMed

    Luby, S P; Agboatwalla, M; Raza, A; Sobel, J; Mintz, E D; Baier, K; Hoekstra, R M; Rahbar, M H; Hassan, R; Qureshi, S M; Gangarosa, E J

    2001-10-01

    We conducted a study in a squatter settlement in Karachi, Pakistan where residents report commonly washing their hands to determine if providing soap, encouraging hand washing, and improving wash-water quality would improve hand cleanliness. We allocated interventions to 75 mothers and collected hand-rinse samples on unannounced visits. In the final model compared with mothers who received no hand-washing intervention, mothers who received soap would be expected to have 65% fewer thermotolerant coliform bacteria on their hands (95% CI 40%, 79%) and mothers who received soap, a safe water storage vessel, hypochlorite for water treatment, and instructions to wash their hands with soap and chlorinated water would be expected to have 74% fewer (95% CI 57%, 84%). The difference between those who received soap alone, and those who received soap plus the safe water vessel was not significant (P = 0.26). Providing soap and promoting hand washing measurably improved mothers' hand cleanliness even when used with contaminated water.

  13. Effectiveness of hand washing and disinfection methods in removing transient bacteria after patient nursing.

    PubMed

    Ojajärvi, J

    1980-10-01

    The effectiveness of various hand washing and disinfection methods in removing transient skin bacteria was studied in hospital after dry or moist contamination of the hands when nursing burn patients. The results were compared with those of laboratory tests with volunteers. A fairly good correlation of the bacterial reductions existed between hospital and laboratory tests. All other methods removed Staph. aureus from the hands more effectively than liquid soap. Gram-negative bacilli were more easily removed than staphylococci, even with soap wash alone. In hospital, none of the washing and disinfection methods always removed all patient-borne bacteria from the hands. After dry or moist contamination and subsequent washing with soap only, colonies of Staph. aureus were often detected in finger-print samples. Staphylococci were more often completely removed by a 4% chlorhexidine detergent scrub and alcoholic solutions (either with or without previous soap wash) than by liquid soap, hexachlorophene or iodophor preparations. Gram-negative bacilli were more easily removed by all the washing and disinfection methods. After moist contamination, Gram-negative bacilli were more often completely removed from the hands by ethanol than by other treatments. The results of the present study emphasize the importance of always using gloves when nursing a profuse spreader of bacteria or one who must be protected from infection.

  14. U-235 Holdup Measurements in the 321-M Lathe HEPA Banks

    SciTech Connect

    Salaymeh, S.R.

    2002-07-08

    The Analytical Development Section of Savannah River Technology Center (SRTC) was requested by the Facilities Decommissioning Division (FDD) to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The results of the holdup assays are essential for determining compliance with the Waste Acceptance Criteria, Material Control and Accountability, and to meet criticality safety controls. This report covers holdup measurements of uranium residue in six high efficiency particulate air (HEPA) filter banks of the A-lathe and B-lathe exhaust systems of the 321-M facility. This report discusses the non-destructive assay measurements, assumptions, calculations, and results of the uranium holdup in these six items.

  15. Cytokine-mediated down-regulation of CYP1A1 in Hepa1 cells.

    PubMed

    Paton, T E; Renton, K W

    1998-06-01

    The activation of host defense mechanisms down-regulates microsomal cytochrome P450 in cell culture, humans, and animals. Investigation into various aspects of this effect using in vivo models has yet to define clearly the role that cytokines play in this phenomenon. The mechanism of down-regulation by immunostimulants, such as lipopolysaccharide (LPS), is explored with an in vitro model, utilizing a murine hepatoma (Hepa1) and a murine macrophage (IC-21) cell line. It is hypothesized that down-regulation of P450 activity by immunostimulants involves the activation of immune cells and the subsequent release of cytokines, such as interleukin-1 (IL-1), interleukin-6 (IL-6), and tumor necrosis factor-alpha (TNF-alpha). The effects of immunostimulation on P450 activity are assessed by ethoxyresorufin O-dealkylase, an assay that measures CYP1A activity in Hepa1 cells. Initial studies demonstrated that LPS added directly to hepatoma cells had no effect on the levels of CYP1A1 activity. In contrast, a significant down-regulation in CYP1A1 activity occurred when hepatoma cells were incubated with monocyte conditioned medium obtained by incubating LPS with IC-21 cells. When pentoxifylline, a TNF-alpha synthesis inhibitor, was co-administered with LPS to macrophages, the down-regulation of CYP1A1 activity was prevented. The direct administration of murine recombinant TNF-alpha to hepatoma cells resulted in a down-regulation of CYP1A1 activity. These results implicated the release of TNF-alpha from macrophages as an important step in the down-regulation of CYP1A1 by LPS. PMID:9714297

  16. Reduction in MRSA environmental contamination with a portable HEPA-filtration unit.

    PubMed

    Boswell, T C; Fox, P C

    2006-05-01

    There is renewed interest in the hospital environment as a potentially important factor for cross-infection with methicillin-resistant Staphylococcus aureus (MRSA) and other nosocomial pathogens. The aim of this study was to evaluate the effectiveness of a portable high-efficiency particulate air (HEPA)-filtration unit (IQAir Cleanroom H13, Incen AG, Goldach, Switzerland) at reducing MRSA environmental surface contamination within a clinical setting. The MRSA contamination rate on horizontal surfaces was assessed with agar settle plates in ward side-rooms of three patients who were heavy MRSA dispersers. Contamination rates were measured at different air filtration rates (60-235 m(3)/h) and compared with no air filtration using Poisson regression. Without air filtration, between 80% and 100% of settle plates were positive for MRSA, with the mean number of MRSA colony-forming units (cfu)/10-h exposure/plate ranging from 4.1 to 27.7. Air filtration at a rate of 140 m(3)/h (one patient) and 235 m(3)/h (two patients), resulted in a highly significant decrease in contamination rates compared with no air filtration (adjusted rate ratios 0.037, 0.099 and 0.248, respectively; P < 0.001 for each). A strong association was demonstrated between the rate of air filtration and the mean number of MRSA cfu/10-h exposure/plate (P for trend < 0.001). In conclusion, this portable HEPA-filtration unit can significantly reduce MRSA environmental contamination within patient isolation rooms, and this may prove to be a useful addition to existing MRSA infection control measures.

  17. Performance testing of HEPA filters: Progress towards a European standard procedure

    SciTech Connect

    Dyment, J.

    1997-08-01

    Proposals for a future European testing procedure for {open_quotes}High Efficiency Particulate Air Filters (HEPA and ULPA){close_quotes} are being developed by CEN (Comite Europeen de Normalisation). The new standard will be given the status of national standard in participating countries, conflicting national standards being withdrawn. The standard will comprise 5 parts covering the grouping and classification of HEPA and ULPA filters according to their efficiency, fundamental principles of testing, marking etc (in part 1). Part 2 will cover aerosol production, measurement principles, counting equipment and statistics. Parts 3-5 will cover testing flat sheet media, leak testing of filter elements and the efficiency testing of filter elements respectively. The efficiency test methods allow the use of either homogeneous monodisperse or polydisperse aerosols for the determination of particulate filtration efficiencies as a function of particle size. The particle size at which maximum penetration occurs is first determined in flat sheet media tests; tests on filter elements (constructed using the same filter medium) may be carried out using either a homogeneous monodisperse aerosol of the size at which maximum penetration occurs (MPPS) or a polydisperse aerosol whose median size is close to the MPPS. Tests with monodisperse aerosols may be conducted using condensation nucleus counting equipment; tests using polydisperse test aerosols require the use of optical sizing particle counters. When determining the efficiency of filter elements the downstream aerosol concentrations may be determined from air samples obtained using either an overall method (single point sampling after mixing) or a scan method. The scan method also allows {open_quotes}local{close_quotes} efficiency values to be determined. 1 ref., 1 fig., 1 tab.

  18. Removal of Pb and Zn from contaminated soil by different washing methods: the influence of reagents and ultrasound.

    PubMed

    Wang, Jiaming; Jiang, Jianguo; Li, Dean; Li, Tianran; Li, Kaimin; Tian, Sicong

    2015-12-01

    Pb and Zn contamination in agricultural soils has become an important issue for human health and the environment. Washing is an effective method for remediating polluted soil. Here, we compare several washing materials and methods in the treatment of Pb- and Zn-polluted farmland soil. We examined four washing reagents, hydrochloric acid, citric acid, Na2EDTA, and tartaric acid, all of which independently removed Zn at rates >65 %. Combining washing reagents markedly enhanced heavy metal removal, by using Na2EDTA and either tartaric acid or lactate in sequence: Pb and Zn removal rates improved to 84.1 and 82.1 % for Na2EDTA-tartaric acid; and to 88.3 and 89.9 % for Na2EDTA-lactate, respectively. Additionally, combining ultrasound with conventional washing methods markedly improved washing efficiency, by shortening washing duration by 96 %. We achieved similar removal rates using ultrasound for 10 min, compared with traditional mechanical vibration alone for 4 h. We concluded that treating Pb- and Zn-contaminated soil with appropriate washing reagents under optimal conditions can greatly enhance the remediation of polluted farmland soils.

  19. Removal of Pb and Zn from contaminated soil by different washing methods: the influence of reagents and ultrasound.

    PubMed

    Wang, Jiaming; Jiang, Jianguo; Li, Dean; Li, Tianran; Li, Kaimin; Tian, Sicong

    2015-12-01

    Pb and Zn contamination in agricultural soils has become an important issue for human health and the environment. Washing is an effective method for remediating polluted soil. Here, we compare several washing materials and methods in the treatment of Pb- and Zn-polluted farmland soil. We examined four washing reagents, hydrochloric acid, citric acid, Na2EDTA, and tartaric acid, all of which independently removed Zn at rates >65 %. Combining washing reagents markedly enhanced heavy metal removal, by using Na2EDTA and either tartaric acid or lactate in sequence: Pb and Zn removal rates improved to 84.1 and 82.1 % for Na2EDTA-tartaric acid; and to 88.3 and 89.9 % for Na2EDTA-lactate, respectively. Additionally, combining ultrasound with conventional washing methods markedly improved washing efficiency, by shortening washing duration by 96 %. We achieved similar removal rates using ultrasound for 10 min, compared with traditional mechanical vibration alone for 4 h. We concluded that treating Pb- and Zn-contaminated soil with appropriate washing reagents under optimal conditions can greatly enhance the remediation of polluted farmland soils. PMID:26300361

  20. 6. GENE WASH DAM, LOOKING NORTHWEST. SURVEY REFLECTOR IN FOREGROUND ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. GENE WASH DAM, LOOKING NORTHWEST. SURVEY REFLECTOR IN FOREGROUND FOR MONITORING MOVEMENT OF DAM AND EARTH. - Gene Wash Reservoir & Dam, 2 miles west of Parker Dam, Parker Dam, San Bernardino County, CA

  1. 4. AERIAL VIEW OF GENE WASH RESERVOIR AND GENE CAMP ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    4. AERIAL VIEW OF GENE WASH RESERVOIR AND GENE CAMP LOOKING SOUTHWEST. DAM AND SPILLWAY VISIBLE IN BOTTOM OF PHOTO. - Gene Wash Reservoir & Dam, 2 miles west of Parker Dam, Parker Dam, San Bernardino County, CA

  2. Salt Wash Field, Grand Country, Utah

    SciTech Connect

    Morgan, C.D. )

    1993-08-01

    The Salt Wash field is located 15 miles southeast of Green River, Utah, in the Paradox fold and fault belt. The field was discovered in 1961 and has produced over 1.3 million bbl of oil and 11.6 billion ft[sup 3] of gas from the Mississippian Leadville LImestone. The average surface elevation is 4389 ft above sea level, and the depth to the top of the oil production is form 8500 to 8914 ft. Salt Wash field is an anticline with over 200 ft of closure on top of the Leadville. The producing zone is in the lower Leadville with intercrystalline and vuggy porosity developed in limestone and crystalline dolomitic limestone. The produced oil is a 50 to 53 API gravity crude with a 40[degrees]F pour point. The gas, a mixture of two sources, is predominately nitrogen (>70[sup [approximately

  3. A new technique for bladder washing.

    PubMed

    Miller, D C; Fitkin, D L; Kropp, K A; Selman, S H

    1992-01-01

    We describe a simple adaptation of the Water Pik (Teledyne Water Pik, Fort Collins, Colorado) irrigating device which allows vigorous, direct-vision agitation of the bladder wall. Three groups of mongrel dogs were subjected to cystoscopy and either syringe barbotage, half-speed Water Pik irrigation, or full-speed Water Pik irrigation of the bladder wall. Transitional cell counts were then done on centrifuged aliquots of each bladder wash specimen. The average number of transitional cells per high-power field were similar between the control group and the syringe barbotage group (2.5 and 1.5 respectively). However, both the half-speed and the full-speed Water Pik groups demonstrated statistically higher cell counts (5.7 and 13.7) when compared to both the controls and syringe barbotage groups. We conclude that Water Pik irrigation is an effective method to increase cell yield in bladder wash specimens. PMID:1729530

  4. Salmonella population rebound and its prevention on spray washed and non-washed jalapeño peppers and roma tomatoes in humid storage.

    PubMed

    Pao, Steven; Long, Wilbert; Kim, Chyer; Rafie, A Reza

    2012-04-01

    The potential of Salmonella population to rebound on non-washed and washed roma tomatoes and jalapeño peppers in humid storage at 4°C, 10°C, 15°C, 21°C, or 35°C for ≤12 days was investigated. The initial inoculation levels of Salmonella on peppers and tomatoes were 5.6 and 5.2 log CFU/cm(2), respectively. Air-drying of fruit surfaces resulted in contamination levels of 3.9 and 3.7 log CFU/cm(2) on inoculated peppers and tomatoes, respectively. At 21°C and 35°C, the levels of air-dried Salmonella inoculums on produce surfaces increased ≥2 log cycles, with the most rapid growth in the first 3 days. Mechanical washing on rollers (rinsing; R-treatment) or revolving brushes (rinsing and brushing; RB-treatment) with water decreased Salmonella counts by ≥2.5 log CFU/cm(2) on both peppers and tomatoes. After R- or RB-treatment, peppers stored at 21°C and 35°C permitted residual Salmonella (≤1.4 log CFU/cm(2)) to grow to 2.6-3.9 log CFU/cm(2). During storage, residual Salmonella (≤1.0 log CFU/cm(2)) on washed tomatoes increased to 3.1 log CFU/cm(2) at 35°C following R-treatment and 3.8 log CFU/cm(2) at 21°C following RB-treatment. Cold storage at 4°C and 10°C effectively prevented the proliferation of Salmonella on both washed and non-washed produce. The current study on jalapeño peppers and roma tomatoes demonstrated that Salmonella population can rebound on produce in humid storage before or after washing. The finding highlights the benefit of uninterrupted cold storage for safer produce operations.

  5. Washing of the AN-107 entrained solids

    SciTech Connect

    GJ Lumetta; FV Hoopes

    2000-03-31

    This report describes the results of a test conducted by Battelle to assess the effects of inhibited water washing on the composition of the entrained solids in the diluted AN-107 low-activity waste (LAW) sample. The objective of this work was to gather data on the solubility of the AN-107 entrained solids in 0.01 M NaOH, so that BNFL can evaluate whether these solids require caustic leaching.

  6. Continuous concentration and constant volume washing of tetraphenylborate slurries

    SciTech Connect

    Siler, J.L.

    1999-12-08

    SRTC has completed filtration testing of tetraphenylborate (TPB) slurries with and without sludge. These tests were slightly different from previous SRS tests in that they used continuous mode concentration and constant volume washing evolutions. The extent of TPB recovery during washing was measured. The resulting washed precipitate slurry, with sludge, was stored at ambient temperature and under a nitrogen-inerted atmosphere to study TPB stability. Samples of both unwashed and washed slurries were submitted for rheology measurements.

  7. Interruption of shigellosis by hand washing.

    PubMed

    Khan, M U

    1982-01-01

    High attack rates, increasing resistance to antibiotics and high mortality make shigellosis a serious problem. As Shigella is associated with poor hygiene we examined the effectiveness of a simple intervention, washing hands with soap and water, in checking the spread of the disease. The study population was comprised of confirmed cases of shigellosis. These and matched controls were followed up for 10 days. Several pieces of soap and earthenware pitchers for storing water were provided to the study families and they were advised to wash their hands with soap and water after defaecation and before meals. Compliance was monitored daily by observing the size of the soap and residual water. Rectal swabs of contacts of both the groups were obtained for culture. The secondary infection rate was 10.1% in the study group and 32.4% in the control group. The secondary case (symptomatic) rate was 2.2% in the study group and 14.2% in the control group. These results suggest that hand-washing has a positive interrupting effect, even in unsanitary environments.

  8. Electrostatic precipitator having traversing collector washing mechanism

    SciTech Connect

    Bricker, J.C.; Elsbernd, C.A.

    1980-12-23

    An electrostatic precipitator air cleaner is described that includes a number of precipitator cells having spaced parallel plates for collecting dirt particles, and a vertically disposed traversing pipe-like spray header containing a number of spray nozzles for directing a spray of wash or rinse fluid onto the collecting plates in order to remove collected particles. The header is traversed horizontally across the precipitator cells by means of a trolley supported by a rail-like guide member and reciprocated between a home position and an extended position by means of a rotating elongated helical drive screw cooperating with a gear-like follower attached to the trolley, such that the rotation of the screw produces linear motion of the header. The header is connected to a source of wash or rinse fluid by means of swivel connections and a flexible conduit. An elongated flat resilient fluid impervious strip containing a longitudinal slit in sliding sealable engagement with the header is positioned between the traversing mechanism and the spray nozzles to prevent infiltration of the precipitator airstream or wash fluid into the area occupied by the traversing mechanism. The threaded follower may also be disengaged from the helical drive screw and the header moved manually to any position along its length of travel.

  9. Ceramic wash-coat for catalyst support

    SciTech Connect

    Kulkarni, Anand A.; Subramanian, Ramesh; Sabol, Stephen M.

    2012-08-14

    A wash-coat (16) for use as a support for an active catalyst species (18) and a catalytic combustor component (10) incorporating such wash-coat. The wash-coat is a solid solution of alumina or alumina-based material (Al.sub.2O.sub.3-0-3 wt % La.sub.2O.sub.3) and a further oxide exhibiting a coefficient of thermal expansion that is lower than that exhibited by alumina. The further oxide may be silicon dioxide (2-30 wt % SiO.sub.2), zirconia silicate (2-30 wt % ZrSiO.sub.4), neodymium oxide (0-4 wt %), titania (Al.sub.2O.sub.3-3-40% TiO.sub.2) or alumina-based magnesium aluminate spinel (Al.sub.2O.sub.3-25 wt % MgO) in various embodiments. The active catalyst species may be palladium and a second metal in a concentration of 10-50% of the concentration of the palladium.

  10. Bacterial Exchange in Household Washing Machines

    PubMed Central

    Callewaert, Chris; Van Nevel, Sam; Kerckhof, Frederiek-Maarten; Granitsiotis, Michael S.; Boon, Nico

    2015-01-01

    Household washing machines (WMs) launder soiled clothes and textiles, but do not sterilize them. We investigated the microbial exchange occurring in five household WMs. Samples from a new cotton T-shirt were laundered together with a normal laundry load. Analyses were performed on the influent water and the ingoing cotton samples, as well as the greywater and the washed cotton samples. The number of living bacteria was generally not lower in the WM effluent water as compared to the influent water. The laundering process caused a microbial exchange of influent water bacteria, skin-, and clothes-related bacteria and biofilm-related bacteria in the WM. A variety of biofilm-producing bacteria were enriched in the effluent after laundering, although their presence in the cotton sample was low. Nearly all bacterial genera detected on the initial cotton sample were still present in the washed cotton samples. A selection for typical skin- and clothes-related microbial species occurred in the cotton samples after laundering. Accordingly, malodour-causing microbial species might be further distributed to other clothes. The bacteria on the ingoing textiles contributed for a large part to the microbiome found in the textiles after laundering. PMID:26696989

  11. Irreversible Wash Aid Additive for Cesium Mitigation: WARRP Demonstration

    SciTech Connect

    Kaminski, Michael

    2015-01-01

    This activity demonstrated, on a practical scale, the primary unit operations for building a containment structure for radioactive wash waters, washing down a hypothetically radioactively contaminated vehicle, collecting the hypothetically radioactive slurry waste water, filtering the hypothetically radioactive wash waters, disassembling the containment, and transporting the materials for final disposition.

  12. Application of Chinese Ink Wash Drawing in Product Design

    NASA Astrophysics Data System (ADS)

    Wang, Qin; Huang, Qiming; Qin, Chuan

    Based on the analysis of the art of Chinese Ink Wash Drawing style, then explains the purpose and meaning of the study for product design with Ink Wash Drawing, in the end combined with actual cases, describes the application of product design using Chinese Ink Wash Drawing.

  13. Changes in the morphometry of Las Vegas Wash and the impact on water quality

    USGS Publications Warehouse

    Roline, Richard A.; Sartoris, James J.

    1988-01-01

    Las Vegas Wash, a natural wash east of Las Vegas, Nevada, carries stormwater, groundwater drainage, and sewage effluent from two sewage treatment plants to Lake Mean. Over 80 percent of the normal discharge of approximately 3.4 m3/s (120 ft3/s) consists of effluent from the City of Las Vegas and Clark County sewage treatment plants. Beginning in the 1950s, a large wetland area developed along the wash that supported waterfowl populations and contributed to some water quality transformations. Heavy rains and subsequent flooding in the area in 1983 and 1984 resulted in erosion and channelization that greatly reduced the wetland area within Las Vegas Wash. The reduction in wetland area shortened water travel time in the wash and affected water quality. The primary impacts on the water entering Lake Mead have been an increase in temperature, a decrease in dissolved oxygen concentration, and an increase in ammonia levels. Other physical-chemical parameters and changes in nutrient transformations are also discussed.

  14. Fresh produce washing aid, T-128, enhances inactivation of salmonella and pseudomonas biofilms on stainless steel in chlorinated wash solutions

    Technology Transfer Automated Retrieval System (TEKTRAN)

    The efficacy of chlorine wash solutions, with/without the washing aid, T-128, on inactivation of Salmonella and Pseudomonas populations in biofilms on stainless steel coupons was evaluated under conditions of increasing organic matter loads in the wash water. Biofilms were formed statically on stai...

  15. Proteomic analysis of HepaRG cells: a novel cell line that supports hepatitis B virus infection.

    PubMed

    Narayan, Ramamurthy; Gangadharan, Bevin; Hantz, Olivier; Antrobus, Robin; García, Angela; Dwek, Raymond A; Zitzmann, Nicole

    2009-01-01

    The first proteomic characterization of the HepaRG cell line, the only cell line that is susceptible to hepatitis B virus (HBV) infection and supports a complete virus life cycle, is reported. Differential analysis of naive and HBV-infected HepaRG cells by two-dimensional gel electrophoresis revealed 19 differentially regulated features, 7 increasing and 12 decreasing with HBV infection. The proteins identified in these features were involved in various cellular pathways including apoptosis, DNA/RNA processing, and hepatocellular impairment. Similar expression changes in a number of the identified proteins have already been reported for other virus systems. Identification of these expression changes is a validation of the proteomics approach and contributes to an understanding of host cellular response to HBV infection.

  16. Hand washing promotion for preventing diarrhoea

    PubMed Central

    Ejemot-Nwadiaro, Regina I; Ehiri, John E; Arikpo, Dachi; Meremikwu, Martin M; Critchley, Julia A

    2015-01-01

    Background Diarrhoea accounts for 1.8 million deaths in children in low- and middle-income countries (LMICs). One of the identified strategies to prevent diarrhoea is hand washing. Objectives To assess the effects of hand washing promotion interventions on diarrhoeal episodes in children and adults. Search methods We searched the Cochrane Infectious Diseases Group Specialized Register (27 May 2015); CENTRAL (published in the Cochrane Library 2015, Issue 5); MEDLINE (1966 to 27 May 2015); EMBASE (1974 to 27 May 2015); LILACS (1982 to 27 May 2015); PsycINFO (1967 to 27 May 2015); Science Citation Index and Social Science Citation Index (1981 to 27 May 2015); ERIC (1966 to 27 May 2015); SPECTR (2000 to 27 May 2015); Bibliomap (1990 to 27 May 2015); RoRe, The Grey Literature (2002 to 27 May 2015); World Health Organization (WHO) International Clinical Trial Registry Platform (ICTRP), metaRegister of Controlled Trials (mRCT), and reference lists of articles up to 27 May 2015. We also contacted researchers and organizations in the field. Selection criteria Individually randomized controlled trials (RCTs) and cluster-RCTs that compared the effects of hand washing interventions on diarrhoea episodes in children and adults with no intervention. Data collection and analysis Three review authors independently assessed trial eligibility, extracted data, and assessed risk of bias. We stratified the analyses for child day-care centres or schools, community, and hospital-based settings. Where appropriate, incidence rate ratios (IRR) were pooled using the generic inverse variance method and random-effects model with 95% confidence intervals (CIs). We used the GRADE approach to assess the quality of evidence. Main results We included 22 RCTs: 12 trials from child day-care centres or schools in mainly high-income countries (54,006 participants), nine community-based trials in LMICs (15,303 participants), and one hospital-based trial among people with acquired immune deficiency

  17. Standing surface acoustic wave (SSAW)-based cell washing

    PubMed Central

    Li, Sixing; Ding, Xiaoyun; Mao, Zhangming; Chen, Yuchao; Nama, Nitesh; Guo, Feng; Li, Peng; Wang, Lin; Cameron, Craig E.; Huang, Tony Jun

    2014-01-01

    Cell/bead washing is an indispensable sample preparation procedure used in various cell studies and analytical processes. In this article, we report a standing surface acoustic wave (SSAW)-based microfluidic device for cell and bead washing in a continuous flow. In our approach, the acoustic radiation force generated in a SSAW field is utilized to actively extract cells or beads from their original medium. A unique configuration of tilted-angle standing surface acoustic wave (taSSAW) is employed in our device, enabling us to wash beads with >98% recovery rate and >97% washing efficiency. We also demonstrate the functionality of our device by preparing high-purity (>97%) white blood cells from lysed blood samples through cell washing. Our SSAW-based cell/bead washing device has the advantages of label-free manipulation, simplicity, high biocompatibility, high recovery rate, and high washing efficiency. It can be useful for many lab-on-a-chip applications. PMID:25372273

  18. Extraction of semivolatile organic compounds from high-efficiency particulate air (HEPA) filters by supercritical carbon dioxide

    SciTech Connect

    Schilling, J.B.

    1997-09-01

    Supercritical fluid extraction (SFE) using unmodified carbon dioxide has been explored as an alternative method for the extraction of semivolatile organic compounds from high-efficiency particulate air (HEPA) filters. HEPA filters provide the final stage of containment on many exhaust systems in US Department of Energy (DOE) facilities by preventing the escape of chemical and radioactive materials entrained in the exhausted air. The efficiency of the filters is tested by the manufacturer and DOE using dioctylphthalate (DOP), a substance regulated by the US Environmental Protection Agency under the Resource Conservation and Recovery Act. Therefore, the filters must be analyzed for semivolatile organics before disposal. Ninety-eight acid, base, and neutral semivolatile organics were spiked onto blank HEPA material and extracted using SFE, Soxhlet, automated Soxhlet, and sonication techniques. The SFE conditions were optimized using a Dionex SFE-703 instrument. Average recoveries for the 98 semivolatile compounds are 82.7% for Soxhlet, 74.0% for sonication, 70.2% for SFE, and 62.9% for Soxtec. Supercritical fluid extraction reduces the extraction solvent volume to 10--15 mL, a factor of 20--30 less than Soxhlet and more than 5 times less than Soxtec and sonication. Extraction times of 30--45 min are used compared to 16--18 h for Soxhlet extraction.

  19. Hepatic differentiation of human pluripotent stem cells on human liver progenitor HepaRG-derived acellular matrix.

    PubMed

    Kanninen, Liisa K; Porola, Pauliina; Niklander, Johanna; Malinen, Melina M; Corlu, Anne; Guguen-Guillouzo, Christiane; Urtti, Arto; Yliperttula, Marjo L; Lou, Yan-Ru

    2016-02-15

    Human hepatocytes are extensively needed in drug discovery and development. Stem cell-derived hepatocytes are expected to be an improved and continuous model of human liver to study drug candidates. Generation of endoderm-derived hepatocytes from human pluripotent stem cells (hPSCs), including human embryonic stem cells and induced pluripotent stem cells, is a complex, challenging process requiring specific signals from soluble factors and insoluble matrices at each developmental stage. In this study, we used human liver progenitor HepaRG-derived acellular matrix (ACM) as a hepatic progenitor-specific matrix to induce hepatic commitment of hPSC-derived definitive endoderm (DE) cells. The DE cells showed much better attachment to the HepaRG ACM than other matrices tested and then differentiated towards hepatic cells, which expressed hepatocyte-specific makers. We demonstrate that Matrigel overlay induced hepatocyte phenotype and inhibited biliary epithelial differentiation in two hPSC lines studied. In conclusion, our study demonstrates that the HepaRG ACM, a hepatic progenitor-specific matrix, plays an important role in the hepatic differentiation of hPSCs.

  20. Washed cell salvage in surgical patients

    PubMed Central

    Meybohm, Patrick; Choorapoikayil, Suma; Wessels, Anke; Herrmann, Eva; Zacharowski, Kai; Spahn, Donat R.

    2016-01-01

    Abstract Background: Cell salvage is commonly used as part of a blood conservation strategy. However concerns among clinicians exist about the efficacy of transfusion of washed cell salvage. Methods: We performed a meta-analysis of randomized controlled trials in which patients, scheduled for all types of surgery, were randomized to washed cell salvage or to a control group with no cell salvage. Data were independently extracted, risk ratio (RR), and weighted mean differences (WMD) with 95% confidence intervals (CIs) were calculated. Data were pooled using a random effects model. The primary endpoint was the number of patients exposed to allogeneic red blood cell (RBC) transfusion. Results: Out of 1140 search results, a total of 47 trials were included. Overall, the use of washed cell salvage reduced the rate of exposure to allogeneic RBC transfusion by a relative 39% (RR = 0.61; 95% CI 0.57 to 0.65; P < 0.001), resulting in an average saving of 0.20 units of allogeneic RBC per patient (weighted mean differences [WMD] = −0.20; 95% CI −0.22 to −0.18; P < 0.001), reduced risk of infection by 28% (RR = 0.72; 95% CI 0.54 to 0.97; P = 0.03), reduced length of hospital stay by 2.31 days (WMD = −2.31; 95% CI −2.50 to −2.11; P < 0.001), but did not significantly affect risk of mortality (RR = 0.92; 95% CI 0.63 to 1.34; P = 0.66). No statistical difference could be observed in the number of patients exposed to re-operation, plasma, platelets, or rate of myocardial infarction and stroke. Conclusions: Washed cell salvage is efficacious in reducing the need for allogeneic RBC transfusion and risk of infection in surgery. PMID:27495095

  1. TANK 4 CHARACTERIZATION, SETTLING, AND WASHING STUDIES

    SciTech Connect

    Bannochie, C.; Pareizs, J.; Click, D.; Zamecnik, J.

    2009-09-29

    A sample of PUREX sludge from Tank 4 was characterized, and subsequently combined with a Tank 51 sample (Tank 51-E1) received following Al dissolution, but prior to a supernate decant by the Tank Farm, to perform a settling and washing study to support Sludge Batch 6 preparation. The sludge source for the majority of the Tank 51-E1 sample is Tank 12 HM sludge. The Tank 51-E1 sample was decanted by SRNL prior to use in the settling and washing study. The Tank 4 sample was analyzed for chemical composition including noble metals. The characterization of the Tank 51-E1 sample, used here in combination with the Tank 4 sample, was reported previously. SRNL analyses on Tank 4 were requested by Liquid Waste Engineering (LWE) via Technical Task Request (TTR) HLE-TTR-2009-103. The sample preparation work is governed by Task Technical and Quality Assurance Plan (TTQAP), and analyses were controlled by an Analytical Study Plan and modifications received via customer communications. Additional scope included a request for a settling study of decanted Tank 51-E1 and a blend of decanted Tank 51-E1 and Tank 4, as well as a washing study to look into the fate of undissolved sulfur observed during the Tank 4 characterization. The chemistry of the Tank 4 sample was modeled with OLI Systems, Inc. StreamAnalyzer to determine the likelihood that sulfate could exist in this sample as insoluble Burkeite (2Na{sub 2}SO{sub 4} {center_dot} Na{sub 2}CO{sub 3}). The OLI model was also used to predict the composition of the blended tank materials for the washing study. The following conclusions were drawn from the Tank 4 analytical results reported here: (1) Any projected blend of Tank 4 and the current Tank 51 contents will produce a SB6 composition that is lower in Ca and U than the current SB5 composition being processed by DWPF. (2) Unwashed Tank 4 has a relatively large initial S concentration of 3.68 wt% on a total solids basis, and approximately 10% of the total S is present as an

  2. Advising parents on washing babies' clothes.

    PubMed

    Scowen, P

    1996-01-01

    Detergents and other laundry products are generally effective and safe for all the family, but use carefully according to the maker's instructions and keep out of the reach of children. Rinse thoroughly to remove detergent residue from fabrics. If handwashing clothes, dissolve detergent before immersing hands. Wear rubber gloves if possible. Wash, rinse and dry hands thoroughly after contact with detergent. If a baby or parent has eczema, it may be necessary to try different products to see which one the client can tolerate. A non-perfumed, non-enzyme product may be found less irritating. PMID:9077252

  3. Physical properties of cobia (Rachycentron canadum) surimi: effect of washing cycle at different salt concentrations.

    PubMed

    Hamzah, N; Sarbon, N M; Amin, A M

    2015-08-01

    This study aimed to determine the effects of 2-5 wash cycles and the addition of tetrasodium pyrophosphate (TSPP) (0 %, 0.05 Surimi% and 0.1 % w/w)-with or without the addition of 0.4 % calcium chloride (CaCl2)-on the physical properties such as texture, colour, expressible moisture and microstructure of Cobia (Rachycentron canadum) surimi gel. The highest breaking force (484.85 g) was obtained with the addition 0.1 % TSPP alone on the fifth wash. However, a combination of 0.1 and 0.4 % CaCl2 in surimi gels at wash cycle 5 resulted in the highest degree of whiteness (86.8 %), as well as total expressible moisture (2.785 %) and deformation (17.11 mm). The highest surimi gel strength (6,923 g.mm) was obtained after three wash cycles with the addition of 0.1 % TSPP +0.4 % CaCl2. The physical properties of Cobia fish surimi gels were affected by the number of wash cycles and treatments with TSPP and CaCl2.

  4. Enhanced Inactivation of Salmonella and Pseudomonas Biofilms on Stainless Steel by Use of T-128, a Fresh-Produce Washing Aid, in Chlorinated Wash Solutions

    PubMed Central

    Shen, Cangliang; Luo, Yaguang; Nou, Xiangwu; Bauchan, Gary; Zhou, Bin; Wang, Qin

    2012-01-01

    The effect of the washing aid T-128 (generally recognized as safe [GRAS] formulation, composed mainly of phosphoric acid and propylene glycol) on inactivation of Salmonella and Pseudomonas populations in biofilms on stainless steel was evaluated under conditions of increasing organic matter loads in chlorinated wash solutions dominated by hypochlorous acid. Biofilms were formed statically on stainless steel coupons suspended in 2% lettuce extract after inoculation with Salmonella enterica serovar Thompson or Newport or with Pseudomonas fluorescens. Coupons with biofilms were washed in chlorine solutions (0, 0.5, 1, 2, 5, 10, or 20 mg/liter at pH 6.5, 5.0 and 2.9), with or without T-128, and with increasing loads of organic matter (0, 0.25, 0.5, 0.75, or 1.0% lettuce extract). Cell populations on coupons were dispersed using intermittent, pulsed ultrasonication and vortexing and enumerated by colony counts on XLT-4 or Pseudomonas agars. Cell responses to fluorescent viability staining of biofilm treatment washing solutions were examined using confocal laser scanning microscopy. Results showed that 0.1% T-128 (without chlorine) reduced P. fluorescens biofilm populations by 2.5 log10 units but did not reduce Salmonella populations. For both Salmonella and Pseudomonas, the sanitizing effect of free chlorine (1.0 to 5.0 mg/liter) was enhanced (P < 0.05) when it was combined with T-128. Application of T-128 decreased the free chlorine depletion rate caused by increasing organic matter in wash waters and significantly (P < 0.05) augmented inactivation of bacteria in biofilms compared to treatments without T-128. Image analysis of surfaces stained with SYTO and propidium iodide corroborate the cultural assay results showing that T-128 can aid in reducing pathogen viability in biofilms and thus can aid in sanitizing stainless steel contact surfaces during processing of fresh-cut produce. PMID:22752180

  5. The chemistry of sludge washing and caustic leaching processes for selected Hanford tank wastes

    SciTech Connect

    Rapko, B.M.; Blanchard, D.L.; Colton, N.G.; Felmy, A.R.; Liu, J.; Lumetta, G.J.

    1996-03-01

    A broad-based study on washing and caustic leaching of Hanford tank sludges was performed in FY 1995 to gain a better understanding of the basic chemical processes that underlie this process. This approach involved testing of the baseline sludge washing and caustic leaching method on several Hanford tank sludges, and characterization of the solids both before and after testing by electron microscopy, X-ray diffraction, and X-ray absorption spectroscopy. A thermodynamically based model was employed to help understand the factors involved in individual specie distribution in the various stages of the sludge washing and caustic leaching treatment. The behavior of the important chemical and radiochemical components throughout the testing is summarized and reviewed in this report.

  6. Bacterial resistance and topical antimicrobial wash products.

    PubMed

    Jones, R D

    1999-08-01

    Current scientific evidence has not shown that a link exists between the use of topical antimicrobial formulations and antiseptic or antibiotic resistance. As a result of the extensive history and varied use of antiseptic products and ingredients, any selective pressure for antibiotic resistance that may be occurring or may be uncovered in the future because of antiseptic use would be expected to be insignificant compared with the selective pressure because of antibiotic use. This review illustrates the effectiveness of topical antimicrobial wash products against antibiotic-resistant and antiseptic-resistant bacteria in use settings as well as the studies performed (antiseptic, deodorant, and oral care) demonstrating the lack of development of resistance in long-term clinical studies. Although these studies illustrate that the use of topical antimicrobial products have not been shown to play a role in the fluctuations of the specific composition or resistance of the skin flora, changes in skin flora have been shown to occur. Based on current knowledge, the benefit from use of topical antimicrobial wash products in combination with standard infection control and personal hygiene practices far outweighs the risk of increased antibiotic resistance.

  7. Response of standard and high-capacity HEPA filters to simulated tornado and explosive transients

    SciTech Connect

    Gregory, W.S.; Smith, P.R.

    1982-03-01

    An investigation was performed to determine the response of standard and high-capacity high-efficiency particulate air filters to simulated tornado and explosive transients. Most of the tests were directed toward evaluating the structural response of high-capacity filters to explosive transients. Selected tests were performed to evaluate the effects of particulate loading on filtration efficiencies. Also, several of the high-capacity filters were subjected to simulated toronado transients. The results indicate that the upper structural limits of high-capacity filters for explosive loading is 6.89-kPa (1-psi) peak pressure and 100-kPa-ms (14.51-psi-ms) impulse. These limits are below the approximately 13.78-kPa (2-psi) peak pressure loadings found for standard HEPA filters. Tests of high-capacity filters preloaded with aerosol indicated that the structural limits were further degraded by approximately 40%. The filtration efficiencies were degraded to approximately 70% when the filters were subjected to aerosol entrained within the shock pulse. The effect of simulated tornado transients on high-capacity filters resulted in an upper structural limit of 11.02 kPa (1.6 psi) for peak pressure.

  8. The histone deacetylase inhibiting drug Entinostat induces lipid accumulation in differentiated HepaRG cells

    NASA Astrophysics Data System (ADS)

    Nunn, Abigail D. G.; Scopigno, Tullio; Pediconi, Natalia; Levrero, Massimo; Hagman, Henning; Kiskis, Juris; Enejder, Annika

    2016-06-01

    Dietary overload of toxic, free metabolic intermediates leads to disrupted insulin signalling and fatty liver disease. However, it was recently reported that this pathway might not be universal: depletion of histone deacetylase (HDAC) enhances insulin sensitivity alongside hepatic lipid accumulation in mice, but the mechanistic role of microscopic lipid structure in this effect remains unclear. Here we study the effect of Entinostat, a synthetic HDAC inhibitor undergoing clinical trials, on hepatic lipid metabolism in the paradigmatic HepaRG liver cell line. Specifically, we statistically quantify lipid droplet morphology at single cell level utilizing label-free microscopy, coherent anti-Stokes Raman scattering, supported by gene expression. We observe Entinostat efficiently rerouting carbohydrates and free-fatty acids into lipid droplets, upregulating lipid coat protein gene Plin4, and relocating droplets nearer to the nucleus. Our results demonstrate the power of Entinostat to promote lipid synthesis and storage, allowing reduced systemic sugar levels and sequestration of toxic metabolites within protected protein-coated droplets, suggesting a potential therapeutic strategy for diseases such as diabetes and metabolic syndrome.

  9. The histone deacetylase inhibiting drug Entinostat induces lipid accumulation in differentiated HepaRG cells.

    PubMed

    Nunn, Abigail D G; Scopigno, Tullio; Pediconi, Natalia; Levrero, Massimo; Hagman, Henning; Kiskis, Juris; Enejder, Annika

    2016-01-01

    Dietary overload of toxic, free metabolic intermediates leads to disrupted insulin signalling and fatty liver disease. However, it was recently reported that this pathway might not be universal: depletion of histone deacetylase (HDAC) enhances insulin sensitivity alongside hepatic lipid accumulation in mice, but the mechanistic role of microscopic lipid structure in this effect remains unclear. Here we study the effect of Entinostat, a synthetic HDAC inhibitor undergoing clinical trials, on hepatic lipid metabolism in the paradigmatic HepaRG liver cell line. Specifically, we statistically quantify lipid droplet morphology at single cell level utilizing label-free microscopy, coherent anti-Stokes Raman scattering, supported by gene expression. We observe Entinostat efficiently rerouting carbohydrates and free-fatty acids into lipid droplets, upregulating lipid coat protein gene Plin4, and relocating droplets nearer to the nucleus. Our results demonstrate the power of Entinostat to promote lipid synthesis and storage, allowing reduced systemic sugar levels and sequestration of toxic metabolites within protected protein-coated droplets, suggesting a potential therapeutic strategy for diseases such as diabetes and metabolic syndrome. PMID:27320682

  10. The histone deacetylase inhibiting drug Entinostat induces lipid accumulation in differentiated HepaRG cells

    PubMed Central

    Nunn, Abigail D. G.; Scopigno, Tullio; Pediconi, Natalia; Levrero, Massimo; Hagman, Henning; Kiskis, Juris; Enejder, Annika

    2016-01-01

    Dietary overload of toxic, free metabolic intermediates leads to disrupted insulin signalling and fatty liver disease. However, it was recently reported that this pathway might not be universal: depletion of histone deacetylase (HDAC) enhances insulin sensitivity alongside hepatic lipid accumulation in mice, but the mechanistic role of microscopic lipid structure in this effect remains unclear. Here we study the effect of Entinostat, a synthetic HDAC inhibitor undergoing clinical trials, on hepatic lipid metabolism in the paradigmatic HepaRG liver cell line. Specifically, we statistically quantify lipid droplet morphology at single cell level utilizing label-free microscopy, coherent anti-Stokes Raman scattering, supported by gene expression. We observe Entinostat efficiently rerouting carbohydrates and free-fatty acids into lipid droplets, upregulating lipid coat protein gene Plin4, and relocating droplets nearer to the nucleus. Our results demonstrate the power of Entinostat to promote lipid synthesis and storage, allowing reduced systemic sugar levels and sequestration of toxic metabolites within protected protein-coated droplets, suggesting a potential therapeutic strategy for diseases such as diabetes and metabolic syndrome. PMID:27320682

  11. The development of a HEPA filter with improved dust holding characteristics

    SciTech Connect

    Dyment, J.; Hamblin, C.

    1995-02-01

    A limitation of the HEPA filters used in the extract of nuclear facilities is their relatively low capacity for captured dust. The costs associated with the disposal of a typical filter means that there are clear incentives to extend filter life. The work described in this report are the initial stages in the development of a filter which incorporates a medium which enhances its dust holding capacity. Experimental equipment was installed to enable the dust loading characteristics of candidate media to be compared with those of the glass fibre based papers currently used in filter construction. These tests involved challenging representative samples of the media with an air stream containing a controlled concentration of thermally generated sodium chloride particles. The dust loading characteristics of the media were then compared in terms of the rate of increasing in pressure differential. A number of {open_quotes}graded density{close_quotes} papers were subsequently identified which appeared to offer significant improvements in dust holding. In the second phase of the programme deep-pleat filters (1,700 M{sup 3}h{sup {minus}1}) incorporating graded density papers were manufactured and tested. Improvements of up to 50% were observed in their capacity for the sub-micron sodium chloride test dust. Smaller differences (15%) were measured when a coarser, carbon black, challenge was used. This is attributed to the differences in the particles sizes of the two dusts.

  12. Removal of oxyfluorfen from ex-situ soil washing fluids using electrolysis with diamond anodes.

    PubMed

    dos Santos, Elisama Vieira; Sáez, Cristina; Martínez-Huitle, Carlos Alberto; Cañizares, Pablo; Rodrigo, Manuel Andres

    2016-04-15

    In this research, firstly, the treatment of soil spiked with oxyfluorfen was studied using a surfactant-aided soil-washing (SASW) process. After that, the electrochemical treatment of the washing liquid using boron doped diamond (BDD) anodes was performed. Results clearly demonstrate that SASW is a very efficient approach in the treatment of soil, removing the pesticide completely by using dosages below 5 g of sodium dodecyl sulfate (SDS) per Kg of soil. After that, complete mineralization of organic matter (oxyflourfen, SDS and by-products) was attained (100% of total organic carbon and chemical oxygen demand removals) when the washing liquids were electrolyzed using BDD anodes, but the removal rate depends on the size of the particles in solution. Electrolysis of soil washing fluids occurs via the reduction in size of micelles until their complete depletion. Lower concentrations of intermediates are produced (sulfate, chlorine, 4-(trifluoromethyl)-phenol and ortho-nitrophenol) during BDD-electrolyzes. Finally, it is important to indicate that, sulfate (coming from SDS) and chlorine (coming from oxyfluorfen) ions play an important role during the electrochemical organic matter removal. PMID:26846982

  13. Removal of oxyfluorfen from ex-situ soil washing fluids using electrolysis with diamond anodes.

    PubMed

    dos Santos, Elisama Vieira; Sáez, Cristina; Martínez-Huitle, Carlos Alberto; Cañizares, Pablo; Rodrigo, Manuel Andres

    2016-04-15

    In this research, firstly, the treatment of soil spiked with oxyfluorfen was studied using a surfactant-aided soil-washing (SASW) process. After that, the electrochemical treatment of the washing liquid using boron doped diamond (BDD) anodes was performed. Results clearly demonstrate that SASW is a very efficient approach in the treatment of soil, removing the pesticide completely by using dosages below 5 g of sodium dodecyl sulfate (SDS) per Kg of soil. After that, complete mineralization of organic matter (oxyflourfen, SDS and by-products) was attained (100% of total organic carbon and chemical oxygen demand removals) when the washing liquids were electrolyzed using BDD anodes, but the removal rate depends on the size of the particles in solution. Electrolysis of soil washing fluids occurs via the reduction in size of micelles until their complete depletion. Lower concentrations of intermediates are produced (sulfate, chlorine, 4-(trifluoromethyl)-phenol and ortho-nitrophenol) during BDD-electrolyzes. Finally, it is important to indicate that, sulfate (coming from SDS) and chlorine (coming from oxyfluorfen) ions play an important role during the electrochemical organic matter removal.

  14. Chelator induced phytoextraction and in situ soil washing of Cu.

    PubMed

    Kos, Bostjan; Lestan, Domen

    2004-11-01

    In a soil column experiment, we investigated the effect of 5 mmol kg(-1) soil addition of citric acid, ethylenediamine tetraacetate (EDTA), diethylenetriamine-pentaacetate (DTPA) and [S,S]-stereoisomer of ethylenediamine-disuccinate (EDDS) on phytoextraction of Cu from a vineyard soil with 162.6 mg kg(-1) Cu, into the test plant Brassica rapa var. pekinensis. We also examined the use of a horizontal permeable barrier, composed of layers of nutrient enriched sawdust and apatite, for reduction of chelator induced Cu leaching. The addition of all chelators, except citric acid, enhanced Cu mobility and caused leaching of 19.5-23% of initial total Cu from the soil column. However, Cu plant uptake did not increase accordingly; the most effective was the EDDS treatment, in which plant Cu concentration reached 37.8 +/-1.3 mg kg(-1) Cu and increased by 3.3-times over the control treatment. The addition of none of the chelators in the concentration range from 5 to 15 mmol kg(-1) exerted any toxic effect on respiratory soil microorganisms. When EDDS was applied into the columns with horizontal permeable barriers, only 0.53 +/- 0.32% of the initial total Cu was leached. Cu (36.7%) was washed from the 18 cm soil layer above the barrier and accumulated in the barrier. Our results indicate that rather than for a reduction of Cu leaching during rather ineffective chelate induced Cu phytoextraction, horizontal permeable barriers could be more effective in a new remediation technique of controlled in situ soil washing of Cu with biodegradable chelates.

  15. Antibacterial perineal washing for prevention of recurrent urinary tract infections.

    PubMed

    Cass, A S; Ireland, G W

    1985-05-01

    Antibacterial ointment applied to the urethral meatus in females with recurrent urinary tract infections (UTIs) has been reported to decrease the incidence of UTIs. The value of perineal washing with the antibacterial lotion, hexachlorophene, in preventing urinary tract infections was determined in 56 females with recurrent UTIs. Of three groups of females one group used hexachlorophene perineal washings morning and night, another group used hexachlorophene perineal washings and an oral antibacterial daily (nitrofurantoin or trimethoprim-sulfamethoxazole), and the third group used the oral antibacterials daily alone. The infections per patient were 3.4 with hexachlorophene washings, 0.5 with hexachlorophene washing and oral antibacterials daily, and 0.9 with oral antibacterials alone. These results suggest that hexachlorophene perineal washing was not effective in preventing UTI in females.

  16. Immersion freezing of birch pollen washing water

    NASA Astrophysics Data System (ADS)

    Augustin, Stefanie; Hartmann, Susan; Pummer, Bernhard; Grothe, Hinrich; Niedermeier, Dennis; Clauss, Tina; Voigtländer, Jens; Tomsche, Laura; Wex, Heike; Stratmann, Frank

    2013-04-01

    Up to now, the importance of pollen for atmospheric ice nucleation was considered to be minor, as they are too large to stay in the atmosphere for a long time. But as recent investigations have shown, not the pollen grains themselves are responsible for freezing, but easily suspendable macromolecules on their surfaces (Pummer et al., 2012). Due to the bursting of pollen grains these ice nucleating active (INA) macromolecules could be numerous in the atmosphere. In the present study, the immersion freezing behavior of birch pollen, i.e. its ice nucleating active (INA) macromolecules, was investigated at the Leipzig Aerosol Cloud Interaction Simulator (LACIS, Hartmann et al., 2011). For this, washing water of two different birch pollen samples with different origin (Northern birch and Southern birch) were used. Immersion freezing of droplets generated from the pollen washing water was observed at temperatures higher than -20 °C for both samples. The main difference between the Northern and the Southern birch pollen was the temperature dependence of the immersion freezing process. Our results suggest that the ice nucleating potential of the Southern birch is controlled by a single type of INA macromolecule, while the Northern birch pollen seem to feature two distinctively different types of INA macromolecules. We determined the heterogeneous nucleation rates for both INA macromolecule types and thereby consistently describe the ice nucleation behavior of both, the Southern and the Northern birch pollen washing water. Furthermore we will suggest a theoretical framework for describing e.g. single INA macromolecule related ice nucleation in atmospheric models. References: Pummer, B. G., Bauer, H., Bernardi, J., Bleicher, S. and Grothe, H.: Suspendable macromolecules are responsible for ice nucleation activity of birch and conifer pollen. Atmos. Chem. Phys., 12, 2541-2550, doi:10.5194/acp-12-2541-2012, 2012. Hartmann, S., Niedermeier, D., Voigtländer, J., Clauss, T

  17. Shift in aggregation, ROS generation, antioxidative defense, lysozyme and acetylcholinesterase activities in the cells of an Indian freshwater sponge exposed to washing soda (sodium carbonate).

    PubMed

    Mukherjee, Soumalya; Ray, Mitali; Ray, Sajal

    2016-09-01

    Washing soda, chemically identified as anhydrous sodium carbonate, is a popular cleaning agent among the rural and urban populations of India which often contaminates the freshwater ponds and lakes, the natural habitat of sponge Eunapius carteri. Present investigation deals with estimation of cellular aggregation, generation of ROS and activities of antioxidant enzymes, lysozyme and acetylcholinesterase in the cells of E. carteri under the environmentally realistic concentrations of washing soda. Prolonged treatment of washing soda inhibited the degree of cellular aggregation. Experimental exposure of 8 and 16mg/l of sodium carbonate for 48h elevated the physiological level of reactive oxygen species (ROS) generation in the agranulocytes, semigranulocytes and granulocytes of E. carteri, whereas, treatment of 192h inhibited the ROS generation in three cellular morphotypes. Activities of superoxide dismutase, catalase and glutathione-S-transferase were recorded to be inhibited under prolonged exposure of washing soda. Washing soda mediated inhibition of ROS generation and depletion in the activities of antioxidant enzymes were indicative to an undesirable shift in cytotoxic status and antioxidative defense in E. carteri. Inhibition in the activity of lysozyme under the treatment of sodium carbonate was suggestive to a severe impairment of the innate immunological efficiency of E. carteri distributed in the washing soda contaminated habitat. Washing soda mediated inhibition in the activity of acetylcholinesterase indicated its neurotoxicity in E. carteri. Washing soda, a reported environmental contaminant, affected adversely the immunophysiological status of E. carteri with reference to cellular aggregation, oxidative stress, antioxidative defense, lysozyme and acetylcholinesterase activity.

  18. Landscape of WASH-relevant Training for Humanitarian Emergencies

    PubMed Central

    Dorea, Caetano

    2015-01-01

    Background: Both employed humanitarian personnel as well as those seeking to start a career as an aid worker are often provided with or seek training on the theme of humanitarian water, sanitation, and hygiene (WASH). The objective of this study was to conduct a landscaping exercise of the available WASH-relevant training for humanitarian emergencies. Methods: An open internet search was performed with specific terms related to humanitarian WASH. Retained search results included those training opportunities (including past ones) that were themed around or with a mentioned relevance to humanitarian WASH. Results and Discussion: A total of 42 training courses relevant to humanitarian emergency WASH were retained. In addition to the more generic/introductory trainings, some provided thematic variations such as coordination of WASH responses, project management, risk reduction, information, education and communication (IEC), and complex emergencies. Timely topics such as urban WASH, Ebola, and WASH innovations were also observed indicating the responsiveness of the training providers to the changing needs of humanitarian WASH response programmes. This survey also revealed a large variety in terms of target audience, duration, fees, location, and language of courses. There was no centralised listing of courses available on the Internet. Limitations of this exercise were also discussed. PMID:26064781

  19. Evaluation of HEPA vacuum cleaning and dry steam cleaning in reducing levels of polycyclic aromatic hydrocarbons and house dust mite allergens in carpets.

    PubMed

    Yu, Chang Ho; Yiin, Lih-Ming; Tina Fan, Zhi-Hua; Rhoads, George G

    2009-01-01

    Dry steam cleaning, which has gained recent attention as an effective method to reduce house dust mite (HDM) allergen concentration and loading in carpets, was evaluated in this study for its efficacy in lowering levels of polycyclic aromatic hydrocarbons (PAHs) as well as HDM allergens. Fifty urban homes with wall-to-wall carpets, mostly low-income and with known lead contamination, were studied in 2003 and 2004. Two carpet-cleaning interventions were compared: Repeated HEPA (High Efficiency Particulate Air filtered) vacuuming alone and repeated HEPA vacuuming supplemented with dry steam cleaning. Vacuum samples were collected to measure carpet loading of dust and contaminants immediately before and after cleaning. Paired comparisons were conducted to evaluate the effectiveness of the cleaning protocols in reducing the levels of PAHs and HDM allergens in carpets. The results indicated that both cleaning methods substantially reduced the loading of PAHs and HDM allergens as well as dust in carpets (p < 0.0001). The reductions in loading of dust (64.4%), PAHs (69.1%), and HDM allergens (85.5%), by dry steam cleaning plus repetitive HEPA vacuuming were larger than the reductions by regular HEPA vacuuming alone: dust (55.5%), PAHs (58.6%), and HDM allergens (80.8%), although the difference was statistically significant only for dust and PAHs. We conclude that intensive HEPA vacuum cleaning substantially reduced the loading of PAHs and HDM allergens in carpets in these urban homes and that dry steam cleaning added modestly to cleaning effectiveness. PMID:19137159

  20. Comparative proteomics reveals novel components at the plasma membrane of differentiated HepaRG cells and different distribution in hepatocyte- and biliary-like cells.

    PubMed

    Petrareanu, Catalina; Macovei, Alina; Sokolowska, Izabela; Woods, Alisa G; Lazar, Catalin; Radu, Gabriel L; Darie, Costel C; Branza-Nichita, Norica

    2013-01-01

    Hepatitis B virus (HBV) is a human pathogen causing severe liver disease and eventually death. Despite important progress in deciphering HBV internalization, the early virus-cell interactions leading to infection are not known. HepaRG is a human bipotent liver cell line bearing the unique ability to differentiate towards a mixture of hepatocyte- and biliary-like cells. In addition to expressing metabolic functions normally found in liver, differentiated HepaRG cells support HBV infection in vitro, thus resembling cultured primary hepatocytes more than other hepatoma cells. Therefore, extensive characterization of the plasma membrane proteome from HepaRG cells would allow the identification of new cellular factors potentially involved in infection. Here we analyzed the plasma membranes of non-differentiated and differentiated HepaRG cells using nanoliquid chromatography-tandem mass spectrometry to identify the differences between the proteomes and the changes that lead to differentiation of these cells. We followed up on differentially-regulated proteins in hepatocytes- and biliary-like cells, focusing on Cathepsins D and K, Cyclophilin A, Annexin 1/A1, PDI and PDI A4/ERp72. Major differences between the two proteomes were found, including differentially regulated proteins, protein-protein interactions and intracellular localizations following differentiation. The results advance our current understanding of HepaRG differentiation and the unique properties of these cells.

  1. Presence of nanoparticles in wash water from conventional silver and nano-silver textiles.

    PubMed

    Mitrano, Denise M; Rimmele, Elisa; Wichser, Adrian; Erni, Rolf; Height, Murray; Nowack, Bernd

    2014-07-22

    Questions about how to regulate nanoenhanced products regularly arise as researchers determine possible nanoparticle transformation(s). Focusing concern on the incorporation and subsequent release of nano-Ag in fabrics often overshadows the fact that many "conventional silver" antimicrobials such as ionic silver, AgCl, metallic Ag, and other forms will also form different species of silver. In this study we used a laboratory washing machine to simulate the household laundering of a number of textiles prepared with known conventional Ag or nano-Ag treatments and a commercially available fabric incorporating yarns coated with bulk metallic Ag. Serial filtration allowed for quantification of total Ag released in various size fractions (>0.45 μm, < 0.45 μm, <0.1 μm, and <10 kDa), while characterization of particles with TEM/EDX provided insight on Ag transformation mechanisms. Most conventional Ag additives yielded more total Ag and more nanoparticulate-sized Ag in the washing liquid than fabrics that used nano-Ag treatments. Incorporating nano-silver into the fiber (as opposed to surface treatments) yielded less total Ag during fabric washing. A variety of metallic Ag, AgCl, and Ag/S particles were observed in washing solution by TEM/EDX to various extents depending on the initial Ag speciation in the fabrics. Very similar particles were also observed when dissolved ionic Ag was added directly into the washing liquid. On the basis of the present study, we can state that all silver-treated textiles, regardless of whether the treatment is "conventional" or "nano", can be a source of silver nanoparticles in washing solution when laundering fabrics. Indeed, in this study we observed that textiles treated with "conventional" silver have equal or greater propensity to form nano-silver particles during washing conditions than those treated with "nano"-silver. This fact needs to be strongly considered when addressing the risks of nano-silver and emphasizes that regulatory

  2. Wash-off potential of urban use insecticides on concrete surfaces.

    PubMed

    Jiang, Weiying; Lin, Kunde; Haver, Darren; Qin, Sujie; Ayre, Gilboa; Spurlock, Frank; Gan, Jay

    2010-06-01

    Contamination of surface aquatic systems by insecticides is an emerging concern in urban watersheds, but sources of contamination are poorly understood, hindering development of regulatory or mitigation strategies. Hardscapes such as concrete surfaces are considered an important facilitator for pesticide runoff following applications around homes. However, pesticide behavior on concrete has seldom been studied, and standardized evaluation methods are nonexistent. In the present study, a simple batch method for measuring pesticide wash-off potential from concrete surfaces was developed, and the dependence of washable pesticide residues was evaluated on pesticide types, formulations, time exposed to outdoor conditions, and number of washing cycles. After application to concrete, the washable fraction of four pyrethroids (bifenthrin, permethrin, cyfluthrin, and cyhalothrin) and fipronil rapidly decreased, with half-lives < or =3 d, likely due to irreversible retention in micropores below the concrete surface. The initial fast decrease was followed by a much slower declining phase with half-lives ranging from one week to two months, and detectable residues were still found in the wash-off solution for most treatments after 112 d. The slow decrease may be attributed to a fraction of pesticides being isolated from degradation or volatilization after retention below the concrete surface. Wash-off potential was consistently higher for solid formulations than for liquid formulations, implying an increased runoff contamination risk for granular and powder formulations. Trace levels of pyrethroids were detected in the wash-off solution even after 14 washing-drying cycles over 42 d under outdoor conditions. Results from the present study suggest that pesticide residues remain on concrete and are available for contaminating runoff for a prolonged time. Mechanisms for the long persistence were not clearly known from the present study and merit further investigation.

  3. Evaluation of management techniques to conserve water in a mechanical head wash blood removal system.

    PubMed

    Galloway, H O; Deotte, R E; Lawrence, T E

    2013-11-01

    This research objectively evaluated methods to conserve water in a mechanical beef head wash system. Digital images of pre-wash and post-wash beef heads were analyzed to quantify the percentage change in red saturation of the image, which was used as an objective measure of cleanliness. Three types of nozzles (fan, three-hole, venturi) and three water pressures (344, 516, 689kPa) were evaluated in a two-way treatment structure. An interaction (P=0.07) was observed between water pressure and nozzle type; the change in red saturation increased as pressure decreased for fan and three-hole nozzles which contrasted with venturi nozzles. The fan nozzle×516kPa pressure treatment used 25L of water per head washed and was used to evaluate the effect of three water temperatures (15, 38, 57°C). Water temperature did not impact (P=0.21) change in red saturation. Reducing water wastage and minimizing the use of heated water could have positive economic benefits to the beef processor. PMID:23793094

  4. Evaluation of management techniques to conserve water in a mechanical head wash blood removal system.

    PubMed

    Galloway, H O; Deotte, R E; Lawrence, T E

    2013-11-01

    This research objectively evaluated methods to conserve water in a mechanical beef head wash system. Digital images of pre-wash and post-wash beef heads were analyzed to quantify the percentage change in red saturation of the image, which was used as an objective measure of cleanliness. Three types of nozzles (fan, three-hole, venturi) and three water pressures (344, 516, 689kPa) were evaluated in a two-way treatment structure. An interaction (P=0.07) was observed between water pressure and nozzle type; the change in red saturation increased as pressure decreased for fan and three-hole nozzles which contrasted with venturi nozzles. The fan nozzle×516kPa pressure treatment used 25L of water per head washed and was used to evaluate the effect of three water temperatures (15, 38, 57°C). Water temperature did not impact (P=0.21) change in red saturation. Reducing water wastage and minimizing the use of heated water could have positive economic benefits to the beef processor.

  5. Evidence on the Effectiveness of Water, Sanitation, and Hygiene (WASH) Interventions on Health Outcomes in Humanitarian Crises: A Systematic Review

    PubMed Central

    Ramesh, Anita; Blanchet, Karl; Ensink, Jeroen H. J.; Roberts, Bayard

    2015-01-01

    Background Water, sanitation, and hygiene (WASH) interventions are amongst the most crucial in humanitarian crises, although the impact of the different WASH interventions on health outcomes remains unclear. Aim To examine the quantity and quality of evidence on WASH interventions on health outcomes in humanitarian crises, as well as evaluate current evidence on their effectiveness against health outcomes in these contexts. Methods A systematic literature review was conducted of primary and grey quantitative literature on WASH interventions measured against health outcomes in humanitarian crises occurring from 1980–2014. Populations of interest were those in resident in humanitarian settings, with a focus on acute crisis and early recovery stages of humanitarian crises in low and middle-income countries. Interventions of interest were WASH-related, while outcomes of interest were health-related. Study quality was assessed via STROBE/CONSORT criteria. Results were analyzed descriptively, and PRISMA reporting was followed. Results Of 3963 studies initially retrieved, only 6 published studies measured a statistically significant change in health outcome as a result of a WASH intervention. All 6 studies employed point-of-use (POU) water quality interventions, with 50% using safe water storage (SWS) and 35% using household water treatment (HWT). All 6 studies used self-reported diarrhea outcomes, 2 studies also reported laboratory confirmed outcomes, and 2 studies reported health treatment outcomes (e.g. clinical admissions). 1 study measured WASH intervention success in relation to both health and water quality outcomes; 1 study recorded uptake (use of soap) as well as health outcomes. 2 studies were unblinded randomized-controlled trials, while 4 were uncontrolled longitudinal studies. 2 studies were graded as providing high quality evidence; 3 studies provided moderate and 1 study low quality evidence. Conclusion The current evidence base on the impact of WASH

  6. The case for improved HEPA-filter mechanical performance standards revisited

    SciTech Connect

    Ricketts, C.I.; Smith, P.R.

    1997-08-01

    Under benign operating conditions, High Efficiency Particulate Air (HEPA) filter units serve as reliable and relatively economical components in the air cleaning systems of nuclear facilities worldwide. Despite more than four decades of filter-unit evaluation and improvements, however, the material strength characteristics of the glass fiber filter medium continue to ultimately limit filter functional reliability. In worst-case scenarios involving fire suppression, loss-of-coolant accidents (LOCA`s), or exposure to shock waves or tornado induced flows, rupture of the filter medium of units meeting current qualification standards cannot be entirely ruled out. Even under so-called normal conditions of operation, instances of filter failure reported in the literature leave open questions of filter-unit reliability. Though developments of filter units with improved burst strengths have been pursued outside the United States, support for efforts in this country has been comparatively minimal. This despite user requests for filters with greater moisture resistance, for example. Or the fact that conventional filter designs result in not only the least robust component to be found in a nuclear air cleaning system, but also the one most sensitive to the adverse effects of conditions deviating from those of normal operation. Filter qualification-test specifications of current codes, standards, and regulatory guidelines in the United States are based primarily upon research performed in a 30-year period beginning in the 1950`s. They do not seem to reflect the benefits of the more significant developments and understanding of filter failure modes and mechanisms achieved since that time. One overseas design, based on such knowledge, has proven reliability under adverse operating conditions involving combined and serial challenges. Its widespread use, however, has faltered on a lack of consensus in upgrading filter performance standards. 34 refs., 2 figs., 3 tabs.

  7. 235U Holdup Measurements in Three 321-M Exhaust HEPA Banks

    SciTech Connect

    Dewberry, R

    2005-02-24

    The Analytical Development Section of Savannah River National Laboratory (SRNL) was requested by the Facilities Disposition Division to determine the holdup of enriched uranium in the 321-M facility as part of an overall deactivation project of the facility. The 321-M facility was used to fabricate enriched uranium fuel assemblies, lithium-aluminum target tubes, neptunium assemblies, and miscellaneous components for the production reactors. The results of the holdup assays are essential for determining compliance with the Waste Acceptance Criteria, Material Control & Accountability, and to meet criticality safety controls. This report covers holdup measurements of uranium residue in three HEPA filter exhaust banks of the 321-M facility. Each of the exhaust banks has dimensions near 7' x 14' x 4' and represents a complex holdup problem. A portable HPGe detector and EG&G Dart system that contains the high voltage power supply and signal processing electronics were used to determine highly enriched uranium (HEU) holdup. A personal computer with Gamma-Vision software was used to control the Dart MCA and to provide space to store and manipulate multiple 4096-channel {gamma}-ray spectra. Some acquisitions were performed with the portable detector configured to a Canberra Inspector using NDA2000 acquisition and analysis software. Our results for each component uses a mixture of redundant point source and area source acquisitions that yielded HEU contents in the range of 2-10 grams. This report discusses the methodology, non-destructive assay (NDA) measurements, assumptions, and results of the uranium holdup in these items. This report includes use of transmission-corrected assay as well as correction for contributions from secondary area sources.

  8. ANALYSIS OF VAPORS FROM METHYLENE CHLORIDE EXTRACTS OF NUCLEAR GRADE HEPA FILTER FIBERGLASS SAMPLES

    SciTech Connect

    FRYE JM; ANASTOS HL; GUTIERREZ FC

    2012-06-07

    While several organic compounds were detected in the vapor samples used in the reenactment of the preparation of mounts from the extracts of nuclear grade high-efficiency particulate air filter fiberglass samples, the most significant species present in the samples were methylene chloride, phenol, phenol-d6, and 2-fluorophenol. These species were all known to be present in the extracts, but were expected to have evaporated during the preparation of the mounts, as the mounts appeared to be dry before any vapor was collected. These species were present at the following percentages of their respective occupational exposure limits: methylene chloride, 2%; phenol, 0.4%; and phenol-d6, 0.6%. However, there is no established limit for 2-fluorophenol. Several other compounds were detected at low levels for which, as in the case of 2-fluorophenol, there are no established permissible exposure limits. These compounds include 2-chlorophenol; N-nitroso-1-propanamine; 2-fluoro-1,1{prime}-biphenyl; 1,2-dihydroacenaphthylene; 2,5-cyclohexadiene-1,4-dione,2,6-bis(1,1-dimethylethyl); trimethyl oxirane; n-propylpropanamine; 2-(Propylamino)ethanol; 4-methoxy-1-butene; 6-methyl-5-hepten-2-one; and 3,4-dimethylpyridine. Some of these were among those added as surrogates or spike standards as part ofthe Advanced Technologies and Laboratories International, Inc. preparation ofthe extract of the HEPA filter media and are indicated as such in the data tables in Section 2, Results; other compounds found were not previously known to be present. The main inorganic species detected (sulfate, sodium, and sulfur) are also consistent with species added in the preparation of the methylene chloride extract of the high-efficiency particulate air sample.

  9. Prototype wash water renovation system integration with goverment-furnished wash fixture

    NASA Technical Reports Server (NTRS)

    1983-01-01

    A total renovation concept for removing objectionable materials from spacecraft wash water to make the water reusable was developed. This concept included ferric chloride pretreatment to coagulate suspended solids such as soap and lint, pressure filtration, and carbon adsorption and ion exchange to remove trace dissolved organics and inorganic salts. A breadboard model which was developed to demonstrate the design adequacy of the various system components and the limits on system capacities and efficiencies.

  10. 33 CFR 157.124 - COW tank washing machines.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 33 Navigation and Navigable Waters 2 2012-07-01 2012-07-01 false COW tank washing machines. 157....124 COW tank washing machines. (a) COW machines must be permanently mounted in each cargo tank. (b) The COW machines in each tank must have sufficient nozzles with the proper diameter, working...

  11. 33 CFR 157.124 - COW tank washing machines.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false COW tank washing machines. 157....124 COW tank washing machines. (a) COW machines must be permanently mounted in each cargo tank. (b) The COW machines in each tank must have sufficient nozzles with the proper diameter, working...

  12. 33 CFR 157.124 - COW tank washing machines.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false COW tank washing machines. 157....124 COW tank washing machines. (a) COW machines must be permanently mounted in each cargo tank. (b) The COW machines in each tank must have sufficient nozzles with the proper diameter, working...

  13. 33 CFR 157.124 - COW tank washing machines.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 33 Navigation and Navigable Waters 2 2014-07-01 2014-07-01 false COW tank washing machines. 157....124 COW tank washing machines. (a) COW machines must be permanently mounted in each cargo tank. (b) The COW machines in each tank must have sufficient nozzles with the proper diameter, working...

  14. 33 CFR 157.124 - COW tank washing machines.

    Code of Federal Regulations, 2013 CFR

    2013-07-01

    ... 33 Navigation and Navigable Waters 2 2013-07-01 2013-07-01 false COW tank washing machines. 157....124 COW tank washing machines. (a) COW machines must be permanently mounted in each cargo tank. (b) The COW machines in each tank must have sufficient nozzles with the proper diameter, working...

  15. EPA SITE DEMONSTRATION OF THE BIOTROL SOIL WASHING PROCESS

    EPA Science Inventory

    A pilot-scale soil washing process, patented by BioTrol, Inc., was demonstrate on soil contaminated by wood treating waste, primarily pentachlorophenol (PCP) and creosote-derived polynuclear aromatic hydrocarbons (PAHs). Although soil washing was the main object of this demonstra...

  16. 30 CFR 1206.458 - Determination of washing allowances.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Determination of washing allowances. 1206.458 Section 1206.458 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL... allowance for the costs of washing lease production that is not royalty bearing. (c) Reporting...

  17. 30 CFR 1206.259 - Determination of washing allowances.

    Code of Federal Regulations, 2012 CFR

    2012-07-01

    ... 30 Mineral Resources 3 2012-07-01 2012-07-01 false Determination of washing allowances. 1206.259 Section 1206.259 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL... allowance for the costs of washing lease production that is not royalty bearing. (c) Reporting...

  18. 49 CFR 393.78 - Windshield wiping and washing systems.

    Code of Federal Regulations, 2011 CFR

    2011-10-01

    ... wiping and washing systems. (a) Vehicles manufactured on or after December 25, 1968. Each bus, truck, and truck-tractor manufactured on or after December 25, 1968, must have a windshield wiping system that... 49 Transportation 5 2011-10-01 2011-10-01 false Windshield wiping and washing systems....

  19. 49 CFR 393.78 - Windshield wiping and washing systems.

    Code of Federal Regulations, 2010 CFR

    2010-10-01

    ... wiping and washing systems. (a) Vehicles manufactured on or after December 25, 1968. Each bus, truck, and truck-tractor manufactured on or after December 25, 1968, must have a windshield wiping system that... 49 Transportation 5 2010-10-01 2010-10-01 false Windshield wiping and washing systems....

  20. 2. VIEW OF WASH TANKS Skins are brought in through ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. VIEW OF WASH TANKS Skins are brought in through hatches, seen on rear wall, and washed of blood and flesh in redwood tanks, with wooden grates to hold skins down in water. Superstructure and screening on tanks are a later alteration, unrelated to this process. - Sealing Plant, St. George Island, Pribilof Islands, Saint George, Aleutians West Census Area, AK

  1. 30 CFR 1206.458 - Determination of washing allowances.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Determination of washing allowances. 1206.458 Section 1206.458 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Indian Coal § 1206.458 Determination of washing allowances. (a) Arm's-length contracts. (1) For...

  2. 30 CFR 1206.259 - Determination of washing allowances.

    Code of Federal Regulations, 2014 CFR

    2014-07-01

    ... 30 Mineral Resources 3 2014-07-01 2014-07-01 false Determination of washing allowances. 1206.259 Section 1206.259 Mineral Resources OFFICE OF NATURAL RESOURCES REVENUE, DEPARTMENT OF THE INTERIOR NATURAL RESOURCES REVENUE PRODUCT VALUATION Federal Coal § 1206.259 Determination of washing allowances. (a) Arm's-length contracts. (1) For...

  3. 30 CFR 206.259 - Determination of washing allowances.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... which the wash plant services, whichever is appropriate, or a unit of production method. After an... market the production for the mutual benefit of the lessee and the lessor, then MMS shall require that... lessee's payments for washing under an arm's-length contract are not based on a dollar-per-unit...

  4. 2. VIEW LOOKING NORTHWEST AT CHINA WASH FLUME ON MAIN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    2. VIEW LOOKING NORTHWEST AT CHINA WASH FLUME ON MAIN CANAL - San Carlos Irrigation Project, China Wash Flume, Main (Florence-Case Grande) Canal at Station 137+00, T4S, R10E, S14, Coolidge, Pinal County, AZ

  5. 1. VIEW LOOKING WEST AT CHINA WASH FLUME ON MAIN ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. VIEW LOOKING WEST AT CHINA WASH FLUME ON MAIN CANAL. - San Carlos Irrigation Project, China Wash Flume, Main (Florence-Case Grande) Canal at Station 137+00, T4S, R10E, S14, Coolidge, Pinal County, AZ

  6. 30 CFR 1206.258 - Washing allowances-general.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 30 Mineral Resources 3 2011-07-01 2011-07-01 false Washing allowances-general. 1206.258 Section 1206.258 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.258 Washing allowances—general....

  7. 7 CFR 2902.51 - Parts wash solutions.

    Code of Federal Regulations, 2010 CFR

    2010-01-01

    ... Items § 2902.51 Parts wash solutions. (a) Definition. Products that are designed to clean parts in manual or automatic cleaning systems. Such systems include, but are not limited to, soak vats and tanks... 7 Agriculture 15 2010-01-01 2010-01-01 false Parts wash solutions. 2902.51 Section...

  8. 7 CFR 2902.51 - Parts wash solutions.

    Code of Federal Regulations, 2011 CFR

    2011-01-01

    ... Items § 2902.51 Parts wash solutions. (a) Definition. Products that are designed to clean parts in manual or automatic cleaning systems. Such systems include, but are not limited to, soak vats and tanks... 7 Agriculture 15 2011-01-01 2011-01-01 false Parts wash solutions. 2902.51 Section...

  9. Wash room, bunkhouse, first floor interior. This room is a ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    Wash room, bunkhouse, first floor interior. This room is a screened porch with the original sinks extant. Light and ventilation was borrowed from the wash room into the toilets and bathing rooms. - Sespe Ranch, Bunkhouse, 2896 Telegraph Road, Fillmore, Ventura County, CA

  10. Behavior of Shiga toxigenic Escherichia coli relevant to lettuce washing processes and consideration of factors for evaluating washing process surrogates.

    PubMed

    Deng, Kaiping; Wang, Xue; Yen, Li-Han; Ding, Hongliu; Tortorello, Mary Lou

    2014-11-01

    Postharvest processes for fresh produce commonly include washing in water containing antimicrobial chemicals, such as chlorine; however, if the antimicrobials are not present in sufficient levels, washing can promote the spread of contamination that might be present. To understand cross-contamination risk during washing, we tested a collection of Shiga toxigenic Escherichia coli (STEC), including O157:H7 and other non-O157 strains, for certain traits during washing of fresh-cut lettuce, i.e., sensitivity to sublethal chlorine levels and ability to cross-contaminate (detach from and attach to) lettuce in the presence of sublethal chlorine levels. Nonpathogenic E. coli Nissle 1917 (EcN) and Pediococcus pentosaceus lactic acid bacterial species (LAB) were included as potential washing process validation surrogates. As measured by extension of the lag phase of growth in media containing 0.15 ppm of chlorine, chlorine sensitivity varied among the STECs. Cross-contamination was assessed by evaluating transfer of bacteria from inoculated to uninoculated leaves during washing. Without chlorine, similar transfer to wash water and uninoculated leaves was shown. In 1 ppm of chlorine, cross-contamination was not detected with most strains, except for the substantial transfer by a STEC O111 strain and EcN in some replicates. Strain O111 and EcN showed less inactivation in 0.25 ppm of chlorine water compared with O157 (P < 0.05). LAB showed similar transfer and similar chlorine inactivation to O157. Considering together the sublethal chlorine sensitivity and detachment/attachment traits, neither EcN nor LAB displayed optimal characteristics as washing process surrogates for the STEC strains, although further evaluation is needed. This work demonstrated a range of behaviors of STEC strains during lettuce washing and may be helpful in hazard characterization, identifying factors to consider for evaluating washing process efficacy, and identifying phenotypic traits to select

  11. Exploratory Disposal and Reuse Feasibility Analysis of Winter Maintenance Wash Water

    PubMed Central

    2016-01-01

    The Ohio Department of Transportation has more than 60 facilities without sewer access generating approximately 19 million gallons of winter maintenance wash water. Off-site disposal is costly, creating the need for sustainable management strategies. The objective of this study was to conduct an exploratory feasibility analysis to assess wash water disposal and potential reuse as brine. Based on a comprehensive literature review and relevant environmental chemistry, a sampling protocol consisting of 31 water quality constituents was utilized for monthly sampling at three geographically distinct Ohio Department of Transportation garages during the winter of 2012. Results were compared to local disposal and reuse guidance limits. Three constituents, including a maximum copper concentration of 858 ppb, exceeded disposal limits, and many constituents also failed to meet reuse limits. Some concentrations were orders of magnitude higher than reuse limits and suggest pre-treatment would be necessary if wash water were reused as brine. These water quality results, in conjunction with copper chemical equilibrium modeling, show pH and dissolved carbon both significantly impact the total dissolved copper concentration and should be measured to assess reuse potential. The sampling protocol and specific obstacles highlighted in this paper aid in the future development of sustainable wash water management strategies. PMID:26908148

  12. Exploratory Disposal and Reuse Feasibility Analysis of Winter Maintenance Wash Water.

    PubMed

    Ullinger, Heather L; Kennedy, Marla J; Schneider, William H; Miller, Christopher M

    2016-01-01

    The Ohio Department of Transportation has more than 60 facilities without sewer access generating approximately 19 million gallons of winter maintenance wash water. Off-site disposal is costly, creating the need for sustainable management strategies. The objective of this study was to conduct an exploratory feasibility analysis to assess wash water disposal and potential reuse as brine. Based on a comprehensive literature review and relevant environmental chemistry, a sampling protocol consisting of 31 water quality constituents was utilized for monthly sampling at three geographically distinct Ohio Department of Transportation garages during the winter of 2012. Results were compared to local disposal and reuse guidance limits. Three constituents, including a maximum copper concentration of 858 ppb, exceeded disposal limits, and many constituents also failed to meet reuse limits. Some concentrations were orders of magnitude higher than reuse limits and suggest pre-treatment would be necessary if wash water were reused as brine. These water quality results, in conjunction with copper chemical equilibrium modeling, show pH and dissolved carbon both significantly impact the total dissolved copper concentration and should be measured to assess reuse potential. The sampling protocol and specific obstacles highlighted in this paper aid in the future development of sustainable wash water management strategies. PMID:26908148

  13. Exploratory Disposal and Reuse Feasibility Analysis of Winter Maintenance Wash Water.

    PubMed

    Ullinger, Heather L; Kennedy, Marla J; Schneider, William H; Miller, Christopher M

    2016-01-01

    The Ohio Department of Transportation has more than 60 facilities without sewer access generating approximately 19 million gallons of winter maintenance wash water. Off-site disposal is costly, creating the need for sustainable management strategies. The objective of this study was to conduct an exploratory feasibility analysis to assess wash water disposal and potential reuse as brine. Based on a comprehensive literature review and relevant environmental chemistry, a sampling protocol consisting of 31 water quality constituents was utilized for monthly sampling at three geographically distinct Ohio Department of Transportation garages during the winter of 2012. Results were compared to local disposal and reuse guidance limits. Three constituents, including a maximum copper concentration of 858 ppb, exceeded disposal limits, and many constituents also failed to meet reuse limits. Some concentrations were orders of magnitude higher than reuse limits and suggest pre-treatment would be necessary if wash water were reused as brine. These water quality results, in conjunction with copper chemical equilibrium modeling, show pH and dissolved carbon both significantly impact the total dissolved copper concentration and should be measured to assess reuse potential. The sampling protocol and specific obstacles highlighted in this paper aid in the future development of sustainable wash water management strategies.

  14. Presence of free-living amoebae in portable and stationary eye wash stations

    SciTech Connect

    Tyndall, R.L.; Lyle, M.M.; Ironside, K.S.

    1987-11-01

    Portable and stationary eye wash stations were tested for the presence of free-living amoebae. Such amoebae may be found in potable waters, and at least one genera, the Acanthamoebae, can cause severe infections when introduced into traumatized eyes. Concentrates or filtrates of water from eye wash stations were placed on nonnutrient agar plates seeded with Escherichia coli. Resultant outgrowths of free-living amoebae, which were morphologically identified as mixtures of Hartmannella and Acanthamoebae, were inoculated intranasally into weanling mice. Subsequently, brain and lung tissues from inject mice were tested for amoebae as an indication of persistent infection. Acanthamoebae and Hartmannella were detected in some eye wash stations at each of four test sites. Both portable and stationary stations harbored Acanthamoebae. Some of the isolates caused persistent pulmonary infection but were not isolated from brain tissue. Flushing stationary eye wash stations temporarily reduced the number of stations positive for amoebae. Treatment of portable stations with 25 ppm of free chlorine also reduced the number of stations harboring amoebae but caused corrosion in some of the stations.

  15. Sequential Washing with Electrolyzed Alkaline and Acidic Water Effectively Removes Pathogens from Metal Surfaces.

    PubMed

    Nakano, Yuichiro; Akamatsu, Norihiko; Mori, Tsuyoshi; Sano, Kazunori; Satoh, Katsuya; Nagayasu, Takeshi; Miyoshi, Yoshiaki; Sugio, Tomomi; Sakai, Hideyuki; Sakae, Eiji; Ichimiya, Kazuko; Hamada, Masahisa; Nakayama, Takehisa; Fujita, Yuhzo; Yanagihara, Katsunori; Nishida, Noriyuki

    2016-01-01

    Removal of pathogenic organisms from reprocessed surgical instruments is essential to prevent iatrogenic infections. Some bacteria can make persistent biofilms on medical devices. Contamination of non-disposable equipment with prions also represents a serious risk to surgical patients. Efficient disinfection of prions from endoscopes and other instruments such as high-resolution cameras remains problematic because these instruments do not tolerate aggressive chemical or heat treatments. Herein, we develop a new washing system that uses both the alkaline and acidic water produced by electrolysis. Electrolyzed acidic water, containing HCl and HOCl as active substances, has been reported to be an effective disinfectant. A 0.15% NaCl solution was electrolyzed and used immediately to wash bio-contaminated stainless steel model systems with alkaline water (pH 11.9) with sonication, and then with acidic water (pH 2.7) without sonication. Two bacterial species (Staphylococcus aureus and Pseudomonas aeruginosa) and a fungus (Candida albicans) were effectively removed or inactivated by the washing process. In addition, this process effectively removed or inactivated prions from the stainless steel surfaces. This washing system will be potentially useful for the disinfection of clinical devices such as neuroendoscopes because electrolyzed water is gentle to both patients and equipment and is environmentally sound.

  16. Sequential Washing with Electrolyzed Alkaline and Acidic Water Effectively Removes Pathogens from Metal Surfaces

    PubMed Central

    Nakano, Yuichiro; Akamatsu, Norihiko; Mori, Tsuyoshi; Sano, Kazunori; Satoh, Katsuya; Nagayasu, Takeshi; Miyoshi, Yoshiaki; Sugio, Tomomi; Sakai, Hideyuki; Sakae, Eiji; Ichimiya, Kazuko; Hamada, Masahisa; Nakayama, Takehisa; Fujita, Yuhzo; Yanagihara, Katsunori; Nishida, Noriyuki

    2016-01-01

    Removal of pathogenic organisms from reprocessed surgical instruments is essential to prevent iatrogenic infections. Some bacteria can make persistent biofilms on medical devices. Contamination of non-disposable equipment with prions also represents a serious risk to surgical patients. Efficient disinfection of prions from endoscopes and other instruments such as high-resolution cameras remains problematic because these instruments do not tolerate aggressive chemical or heat treatments. Herein, we develop a new washing system that uses both the alkaline and acidic water produced by electrolysis. Electrolyzed acidic water, containing HCl and HOCl as active substances, has been reported to be an effective disinfectant. A 0.15% NaCl solution was electrolyzed and used immediately to wash bio-contaminated stainless steel model systems with alkaline water (pH 11.9) with sonication, and then with acidic water (pH 2.7) without sonication. Two bacterial species (Staphylococcus aureus and Pseudomonas aeruginosa) and a fungus (Candida albicans) were effectively removed or inactivated by the washing process. In addition, this process effectively removed or inactivated prions from the stainless steel surfaces. This washing system will be potentially useful for the disinfection of clinical devices such as neuroendoscopes because electrolyzed water is gentle to both patients and equipment and is environmentally sound. PMID:27223116

  17. Genesis Eco Systems, Inc. soil washing process

    SciTech Connect

    Cena, R.J.

    1994-10-11

    The Genesis soil washing system is an integrated system of modular design allowing for maximum material handling capabilities, with optimized use of space for site mobility. The Surfactant Activated Bio-enhanced Remediation Equipment-Generation 1 (SABRE-1, Patent Applied For) modification was developed specifically for removing petroleum byproducts from contaminated soils. Scientifically formulated surfactants, introduced by high pressure spray nozzles, displace the contaminant from the surface of the soil particles into the process solution. Once the contaminant is dispersed into the liquid fraction of the process, it is either mechanically removed, chemically oxidized, or biologically oxidized. The contaminated process water is pumped through the Genesis Biosep (Patent Applied For) filtration system where the fines portion is flocculated, and the contaminant-rich liquid portion is combined with an activated mixture of nutrients and carefully selected bacteria to decompose the hydrocarbon fraction. The treated soil and dewatered fines are transferred to a bermed stockpile where bioremediation continues during drying. The process water is reclaimed, filtered, and recycled within the system.

  18. Study of the effect of humidity, particle hygroscopicity and size on the mass loading capacity of HEPA filters

    SciTech Connect

    Gupta, A.

    1992-01-01

    The effect of humidity, particle hygroscopicity and size on the mass loading capacity of glass fiber HEPA filters has been studied. At humidifies above the deliquescent point, the pressure drop across the HEPA filter increased non-linearly with the areal loading density (mass collected/filtration area) of NaCl aerosol, thus significantly reducing the mass loading capacity of the filter compared to dry hygroscopic or non-hygroscopic particle mass loadings. The specific cake resistance, K{sub 2}, has been computed for different test conditions and used as a measure of the mass loading capacity. K. was found to decrease with increasing humidity for the non-hygroscopic aluminum oxide particles and the hygroscopic NaCl particles (at humidities below the deliquescent point). It is postulated that an increase in humidity leads to the formation of a more open particulate cake which lowers the pressure drop for a given mass loading. A formula for predicting K{sub 2} for lognormally distributed aerosols (parameters obtained from impactor data) is derived. The resistance factor, R, calculated using this formula was compared to the theoretical R calculated using the Rudnick-Happel expression. For the non-hygroscopic aluminum oxide the agreement was good but for the hygroscopic sodium chloride, due to large variation in the cake porosity estimates, the agreement was poor.

  19. Study of the effect of humidity, particle hygroscopicity and size on the mass loading capacity of HEPA filters

    SciTech Connect

    Gupta, A.

    1992-09-01

    The effect of humidity, particle hygroscopicity and size on the mass loading capacity of glass fiber HEPA filters has been studied. At humidifies above the deliquescent point, the pressure drop across the HEPA filter increased non-linearly with the areal loading density (mass collected/filtration area) of NaCl aerosol, thus significantly reducing the mass loading capacity of the filter compared to dry hygroscopic or non-hygroscopic particle mass loadings. The specific cake resistance, K{sub 2}, has been computed for different test conditions and used as a measure of the mass loading capacity. K. was found to decrease with increasing humidity for the non-hygroscopic aluminum oxide particles and the hygroscopic NaCl particles (at humidities below the deliquescent point). It is postulated that an increase in humidity leads to the formation of a more open particulate cake which lowers the pressure drop for a given mass loading. A formula for predicting K{sub 2} for lognormally distributed aerosols (parameters obtained from impactor data) is derived. The resistance factor, R, calculated using this formula was compared to the theoretical R calculated using the Rudnick-Happel expression. For the non-hygroscopic aluminum oxide the agreement was good but for the hygroscopic sodium chloride, due to large variation in the cake porosity estimates, the agreement was poor.

  20. Allogeneic hematopoietic SCT performed in non-HEPA filter rooms: initial experience from a single center in India.

    PubMed

    Kumar, R; Naithani, R; Mishra, P; Mahapatra, M; Seth, T; Dolai, T K; Bhargava, R; Saxena, R

    2009-01-01

    In developing countries, it is important to ascertain the safety of performing allogeneic hematopoietic SCT (HSCT) in single rooms without high-efficiency particulate air (HEPA) filters. We present our experience of performing 40 such transplants from July 2004 to November 2007. Source of stem cells was peripheral blood in 33, bone marrow in six and combined in one. G-CSF started from day +1. The indications were SAA-18, CML-7, AML-7, ALL-2, myelodysplastic syndrome-2 and thalassemia major-4. The median age was 19 years (range 2.2-46) with 29 male and 11 female participants. Antibacterial and antifungal prophylaxis was administered along with conditioning, and at the onset of fever, systemic antibiotics were started. Antifungal agents were added if fever persisted for 3 days. Median time for neutrophil engraftment was 10 days (range 8-17). Fever occurred in 38 (95%) for a median of 5 days (range 1-38), and blood cultures were positive in seven (17.5%). Systemic antibiotics were used in 95% and antifungals in 57.5% cases. The 30-day mortality was nil, and 100-day mortality was 1 (2.5%). After day 100, there were eight fatalities (20%) due to chronic GVHD-3, relapse-2, graft rejection-2, disseminated tuberculosis and aspergillosis-1. Our experience suggests that allogeneic HSCT can be safely performed in non-HEPA filter rooms in India. PMID:18794872

  1. Walking in the high-rise city: a Health Enhancement and Pedometer-determined Ambulatory (HEPA) program in Hong Kong

    PubMed Central

    Leung, Angela YM; Cheung, Mike KT; Tse, Michael A; Shum, Wai Chuen; Lancaster, BJ; Lam, Cindy LK

    2014-01-01

    Due to the lack of good infrastructure in the public estates, many older adults in urban areas are sedentary. The Health Enhancement and Pedometer-Determined Ambulatory (HEPA) program was developed to assist older adults with diabetes and/or hypertension to acquire walking exercise habits and to build social support, while engaged in regular physical activity. This study aimed to describe the HEPA program and to report changes in participants’ walking capacity and body strength after 10-week walking sessions. A pre- and postintervention design was used. Pedometers were used to measure the number of steps taken per day before and after the 10-week intervention. Upper and lower body strength, lower body flexibility, and quality of life were assessed. A total of 205 older adults completed the program and all health assessments. After the 10-week intervention, the average number of steps per day increased by 36%, from 6,591 to 8,934. Lower body strength, upper body strength, and aerobic fitness increased significantly after 10 weeks, along with improvement in the 12-item Short Form Health Survey (SF™-12) physical and mental health component summary scores. A social support network was built in the neighborhood, and the local environment was utilized to make walking possible and enjoyable. PMID:25170259

  2. [To wash or not to wash the hands? Reasons for a nursing team].

    PubMed

    Martini, Angela Conte; Dall'Agnol, Clarice Maria

    2005-04-01

    A qualitative study was performed by asking the nursing team at an emergency care hospital about the reasons that lead them to wash their hands or not, since this is an important measure to control cross infection in hospitals. The data, obtained by using the focus groups technique were submitted to enunciation analysis, resulting in emerging topics. It was found out that the supply of material and environmental resources is essential but does not solve all problems. The procedure is performed mainly because of visible dirt and it is a neglected and undervalued practice with predominant focus on protecting the professionals.

  3. Microbiological aspects of washing hands in slaughter-houses.

    PubMed

    de Wit, J C; Kampelmacher, E H

    1982-01-01

    The hand hygiene of workers in a number of chicken-, pig-, calf- and cattle slaughter-houses was investigated. The number of E. coli and salmonellae on hands was determined before and after washing hands in order to measure the washing effect on the number of these faecal bacteria. All workers examined carried E. coli on their hands during work. The average logarithmic E. coli count on hands before washing was about 5.0 in chicken-and calf-slaughter-houses, about 3.5 in pig-and 3.0 in cattle-slaughter-houses. Hand washing decreased the E. coli count per hand by about 1.5 log cycle. Salmonellae were isolated from the hands in chicken- (59 pos./145 samples), pig-(42 pos./116 samples) and calf-slaughter-houses (11 pos./68 samples). Even after washing salmonellae were found to be present. Generally 'normal' washing causes a considerable reduction in the number of transient bacteria on hands. The presence of E. coli and Salmonella after washing, however, indicates that the effectiveness of the procedure needs to be improved.

  4. Immersion freezing of birch pollen washing water

    NASA Astrophysics Data System (ADS)

    Augustin, S.; Wex, H.; Niedermeier, D.; Pummer, B.; Grothe, H.; Hartmann, S.; Tomsche, L.; Clauss, T.; Voigtländer, J.; Ignatius, K.; Stratmann, F.

    2013-11-01

    Birch pollen grains are known to be ice nucleating active biological particles. The ice nucleating activity has previously been tracked down to biological macromolecules that can be easily extracted from the pollen grains in water. In the present study, we investigated the immersion freezing behavior of these ice nucleating active (INA) macromolecules. Therefore we measured the frozen fractions of particles generated from birch pollen washing water as a function of temperature at the Leipzig Aerosol Cloud Interaction Simulator (LACIS). Two different birch pollen samples were considered, with one originating from Sweden and one from the Czech Republic. For the Czech and Swedish birch pollen samples, freezing was observed to start at -19 and -17 °C, respectively. The fraction of frozen droplets increased for both samples down to -24 °C. Further cooling did not increase the frozen fractions any more. Instead, a plateau formed at frozen fractions below 1. This fact could be used to determine the amount of INA macromolecules in the droplets examined here, which in turn allowed for the determination of nucleation rates for single INA macromolecules. The main differences between the Swedish birch pollen and the Czech birch pollen were obvious in the temperature range between -17 and -24 °C. In this range, a second plateau region could be seen for Swedish birch pollen. As we assume INA macromolecules to be the reason for the ice nucleation, we concluded that birch pollen is able to produce at least two different types of INA macromolecules. We were able to derive parameterizations for the heterogeneous nucleation rates for both INA macromolecule types, using two different methods: a simple exponential fit and the Soccer ball model. With these parameterization methods we were able to describe the ice nucleation behavior of single INA macromolecules from both the Czech and the Swedish birch pollen.

  5. Hand washing frequencies and procedures used in retail food services.

    PubMed

    Strohbehn, Catherine; Sneed, Jeannie; Paez, Paola; Meyer, Janell

    2008-08-01

    Transmission of viruses, bacteria, and parasites to food by way of improperly washed hands is a major contributing factor in the spread of foodborne illnesses. Field observers have assessed compliance with hand washing regulations, yet few studies have included consideration of frequency and methods used by sectors of the food service industry or have included benchmarks for hand washing. Five 3-h observation periods of employee (n = 80) hand washing behaviors during menu production, service, and cleaning were conducted in 16 food service operations for a total of 240 h of direct observation. Four operations from each of four sectors of the retail food service industry participated in the study: assisted living for the elderly, childcare, restaurants, and schools. A validated observation form, based on 2005 Food Code guidelines, was used by two trained researchers. Researchers noted when hands should have been washed, when hands were washed, and how hands were washed. Overall compliance with Food Code recommendations for frequency during production, service, and cleaning phases ranged from 5% in restaurants to 33% in assisted living facilities. Procedural compliance rates also were low. Proposed benchmarks for the number of times hand washing should occur by each employee for each sector of food service during each phase of operation are seven times per hour for assisted living, nine times per hour for childcare, 29 times per hour for restaurants, and 11 times per hour for schools. These benchmarks are high, especially for restaurant employees. Implementation would mean lost productivity and potential for dermatitis; thus, active managerial control over work assignments is needed. These benchmarks can be used for training and to guide employee hand washing behaviors. PMID:18724759

  6. [Screening and identification of microorganisms for decolorization of molasses spent wash].

    PubMed

    Li, Bi-Jin; Liu, You-Yan; He, Kai; Teng, Fang-Ming; He, Xi-Pu; Li, Qing-Yun

    2012-09-01

    Microorganisms were screened from the natural environment for decolorization of molasses spent wash, and the isolated strains were then employed in the treatment of actual wastewater. The primary screening was carried out on agar plates supplemented with synthesized melanoidin as the target substrate, since melanoidin is one of the most refractory pigments in wastewater. Promising microorganisms were further selected through secondary screening by decolorization of untreated actual wastewater in shaking flask cultures. Gel filtration chromatography was used to determine the molecular weight distribution of pigments in molasses spent wash before and after decolorization. A strain named A5P1 was isolated from the soil samples collected, showing a good ability of decolorizing molasses spent wash, and was later identified as Aspergillus flavus by morphology and ITS sequence analysis. Experimental study of factors affecting the decolorization performance of strain A5P1 gave the optimal conditions as follows: 4.3 x 10(4) mL(-1) of inoculum size, medium with initial pH of 4.5 and cultivation at 39 degrees C. It could decolorize 53.0% of the pigments in the untreated molasses spent wash and decreased 80% of chemical oxygen demand after four-day incubation. The result of gel filtration chromatography demonstrated that both the large and small molecular weight fractions of pigments in the molasses spent wash could be removed by strain A5P1. Based on the measurement of enzyme activities, at least three different kinds of enzymes, i. e. the enzyme with H2O2-producing activity, laccase and manganese peroxidase were involved in the decolorization process. Therefore, the decolorization mechanism of strain A5P1 was preliminarily considered to be mainly biodegradation, with bioadsorption as a minor reaction.

  7. Pulsed-plasma gas-discharge inactivation of microbial pathogens in chilled poultry wash water.

    PubMed

    Rowan, N J; Espie, S; Harrower, J; Anderson, J G; Marsili, L; MacGregor, S J

    2007-12-01

    A pulsed-plasma gas-discharge (PPGD) system was developed for the novel decontamination of chilled poultry wash water. Treatment of poultry wash water in the plasma generation chamber for up to 24 s at 4 degrees C reduced Escherichia coli NCTC 9001, Campylobacter jejuni ATCC 33560, Campylobacter coli ATCC 33559, Listeria monocytogenes NCTC 9863, Salmonella enterica serovar Enteritidis ATCC 4931, and S. enterica serovar Typhimurium ATCC 14028 populations to non-detectable levels (< or = 8 log CFU/ml). Although similar PPGD treatments at 4 degrees C also produced significant reductions (> or = 3 log CFU/ml) in recalcitrant B. cereus NCTC 11145 endospore numbers within 30 s, the level of endospore reduction was dependent on the nature of the sparged gas used in the plasma treatments. Scanning electron microscopy revealed that significant damage occurred at the cellular level in PPGD-treated test organisms. This electrotechnology delivers energy in intense ultrashort bursts, generating products such as ozone, UV light, acoustic and shock waves, and pulsed electric fields that have multiple bactericidal properties. This technology offers an exciting complementary or alternative approach for treating raw poultry wash water and for preventing cross-contamination in processing environments.

  8. Experimental study of the constituents of space wash water

    NASA Technical Reports Server (NTRS)

    Putnam, D. F.; Colombo, G. V.

    1975-01-01

    This report presents experimental data, obtained under controlled conditions, which quantify the various constituents of human origin that may be expected in space wash water. The experiments were conducted with a simulated crew of two male and two female subjects. The data show that the expected wash water contaminants originating from human secretions are substantially lower than theoretical projections indicated. The data presented are immediately useful and may have considerable impact on the tradeoff comparisons among various unit processes and systems under consideration by NASA for recycling space wash water.

  9. Effects of soap-water wash on human epidermal penetration.

    PubMed

    Zhu, Hanjiang; Jung, Eui-Chang; Phuong, Christina; Hui, Xiaoying; Maibach, Howard

    2016-08-01

    Skin decontamination is a primary interventional method used to decrease dermal absorption of hazardous contaminants, including chemical warfare agents, pesticides and industrial pollutants. Soap and water wash, the most common and readily available decontamination system, may enhance percutaneous absorption through the "wash-in effect." To understand better the effect of soap-water wash on percutaneous penetration, and provide insight to improving skin decontamination methods, in vitro human epidermal penetration rates of four C(14) -labeled model chemicals (hydroquinone, clonidine, benzoic acid and paraoxon) were assayed using flow-through diffusion cells. Stratum corneum (SC) absorption rates of these chemicals at various hydration levels (0-295% of the dry SC weights) were determined and compared with the results of the epidermal penetration study to clarify the effect of SC hydration on skin permeability. Results showed accelerated penetration curves of benzoic acid and paraoxon after surface wash at 30 min postdosing. Thirty minutes after washing (60 min postdosing), penetration rates of hydroquinone and benzoic acid decreased due to reduced amounts of chemical on the skin surface and in the SC. At the end of the experiment (90 min postdosing), a soap-water wash resulted in lower hydroquinone penetration, greater paraoxon penetration and similar levels of benzoic acid and clonidine penetration compared to penetration levels in the non-wash groups. The observed wash-in effect agrees with the enhancement effect of SC hydration on the SC chemical absorption rate. These results suggest SC hydration derived from surface wash to be one cause of the wash-in effect. Further, the occurrence of a wash-in effect is dependent on chemical identity and elapsed time between exposure and onset of decontamination. By reducing chemical residue quantity on skin surface and in the SC reservoir, the soap-water wash may decrease the total quantity of chemical absorbed in the

  10. Endotoxins in cotton: washing effects and size distribution

    SciTech Connect

    Olenchock, S.A.; Mull, J.C.; Jones, W.G.

    1983-01-01

    Endotoxin contamination was measured in washed and unwashed cottons from three distinct growing areas, California, Mississippi, and Texas. The data show differences in endotoxin contamination based upon the geographic source of the cotton. It is also shown that washing bulk cotton before the carding process results in lower endotoxin in the cotton dust. Washing conditions can affect the endotoxin levels, and all size fractions of the airborne dust contain quantifiable endotoxin contamination. Endotoxin analyses provide a simple and reliable method for monitoring the cleanliness of cotton or airborne cotton dusts.

  11. Experimental study of the constituents of space wash water

    NASA Technical Reports Server (NTRS)

    Colombo, G. V.; Putnam, D. F.

    1976-01-01

    Data are presented that quantify some of the various constituents of human origin that may be expected in space wash water. The experiments were conducted under controlled conditions with a simulated crew of two male and two female subjects. The data show that the expected wash water constituents originating from human secretions are substantially lower than theoretical projections have indicated. Average daily quantities as well as individual extremes are given for both shower and laundry water. In addition, concentrations are presented for a projected model of wash water usage in a space station.

  12. Effects of soap-water wash on human epidermal penetration.

    PubMed

    Zhu, Hanjiang; Jung, Eui-Chang; Phuong, Christina; Hui, Xiaoying; Maibach, Howard

    2016-08-01

    Skin decontamination is a primary interventional method used to decrease dermal absorption of hazardous contaminants, including chemical warfare agents, pesticides and industrial pollutants. Soap and water wash, the most common and readily available decontamination system, may enhance percutaneous absorption through the "wash-in effect." To understand better the effect of soap-water wash on percutaneous penetration, and provide insight to improving skin decontamination methods, in vitro human epidermal penetration rates of four C(14) -labeled model chemicals (hydroquinone, clonidine, benzoic acid and paraoxon) were assayed using flow-through diffusion cells. Stratum corneum (SC) absorption rates of these chemicals at various hydration levels (0-295% of the dry SC weights) were determined and compared with the results of the epidermal penetration study to clarify the effect of SC hydration on skin permeability. Results showed accelerated penetration curves of benzoic acid and paraoxon after surface wash at 30 min postdosing. Thirty minutes after washing (60 min postdosing), penetration rates of hydroquinone and benzoic acid decreased due to reduced amounts of chemical on the skin surface and in the SC. At the end of the experiment (90 min postdosing), a soap-water wash resulted in lower hydroquinone penetration, greater paraoxon penetration and similar levels of benzoic acid and clonidine penetration compared to penetration levels in the non-wash groups. The observed wash-in effect agrees with the enhancement effect of SC hydration on the SC chemical absorption rate. These results suggest SC hydration derived from surface wash to be one cause of the wash-in effect. Further, the occurrence of a wash-in effect is dependent on chemical identity and elapsed time between exposure and onset of decontamination. By reducing chemical residue quantity on skin surface and in the SC reservoir, the soap-water wash may decrease the total quantity of chemical absorbed in the

  13. Percutaneous penetration and pharmacodynamics: Wash-in and wash-off of sunscreen and insect repellent.

    PubMed

    Rodriguez, Jocelyn; Maibach, Howard I

    2016-01-01

    Increased awareness of skin cancer and mosquito-transmitted diseases has increased use of insect repellents and sunscreens. The challenge in setting recommendations for use and reapplication, especially when used concomitantly, lies in finding the balance between applying a durable product effective in withstanding natural and physical factors such as water, sweat, temperature and abrasion, while limiting percutaneous absorption and decreasing risk of potential dermal and systemic toxicity. Inorganic sunscreens show no or little percutaneous absorption or toxic effects in comparison to organic sunscreens, which show varying levels of dermal penetration and cutaneous adverse effects. An alternative to N,N-diethyl-m-toluamide (DEET), the traditional gold standard compound in insect repellents, picaridin appears as efficacious, has lower risk of toxicity, and when used simultaneously with sunscreen may decrease percutaneous absorption of both compounds. Conversely, combined use of DEET and sunscreen results in significantly higher absorption of both compounds. It is important to increase consumer awareness of "washing in" of various compounds leading to increased risk of toxicity, as well as differences in reapplication need due to "washing off" caused by water, sweat and abrasion. Although much remains to be studied, to maximize efficacy and decrease toxicity, contemporary research tools, including dermatopharmokinetics, should aid these prospective advances. PMID:26811157

  14. Percutaneous penetration and pharmacodynamics: Wash-in and wash-off of sunscreen and insect repellent.

    PubMed

    Rodriguez, Jocelyn; Maibach, Howard I

    2016-01-01

    Increased awareness of skin cancer and mosquito-transmitted diseases has increased use of insect repellents and sunscreens. The challenge in setting recommendations for use and reapplication, especially when used concomitantly, lies in finding the balance between applying a durable product effective in withstanding natural and physical factors such as water, sweat, temperature and abrasion, while limiting percutaneous absorption and decreasing risk of potential dermal and systemic toxicity. Inorganic sunscreens show no or little percutaneous absorption or toxic effects in comparison to organic sunscreens, which show varying levels of dermal penetration and cutaneous adverse effects. An alternative to N,N-diethyl-m-toluamide (DEET), the traditional gold standard compound in insect repellents, picaridin appears as efficacious, has lower risk of toxicity, and when used simultaneously with sunscreen may decrease percutaneous absorption of both compounds. Conversely, combined use of DEET and sunscreen results in significantly higher absorption of both compounds. It is important to increase consumer awareness of "washing in" of various compounds leading to increased risk of toxicity, as well as differences in reapplication need due to "washing off" caused by water, sweat and abrasion. Although much remains to be studied, to maximize efficacy and decrease toxicity, contemporary research tools, including dermatopharmokinetics, should aid these prospective advances.

  15. Cross contamination of Escherichia coli O157:H7 between lettuce and wash water during home-scale washing.

    PubMed

    Jensen, Dane A; Friedrich, Loretta M; Harris, Linda J; Danyluk, Michelle D; Schaffner, Donald W

    2015-04-01

    Lettuce and leafy greens have been implicated in multiple foodborne disease outbreaks. This study quantifies cross contamination between lettuce pieces in a small-scale home environment. A five-strain cocktail of relevant Escherichia coli O157:H7 strains was used. Bacterial transfer between single inoculated lettuce leaf pieces to 10 non-inoculated lettuce leaf pieces that were washed in a stainless steel bowl of water for 30 s, 1 min, 2 min, and 5 min was quantified. Regardless of washing time, the wash water became contaminated with 90-99% of bacteria originally present on the inoculated lettuce leaf piece. The E. coli O157:H7 concentration on initially inoculated leaf pieces was reduced ∼ 2 log CFU. Each initially uncontaminated lettuce leaf piece had ∼ 1% of the E. coli O157:H7 from the inoculated lettuce piece transferred to it after washing, with more transfer occurring during the shortest (30 s) and longest (5 min) wash times. In all cases the log percent transfer rates were essentially normally distributed. In all scenarios, most of the E. coli O157:H7 (90-99%) transferred from the inoculated lettuce pieces to the wash water. Washing with plain tap water reduces levels of E. coli O157:H7 on the inoculated lettuce leaf pieces, but also spreads contamination to previously uncontaminated leaf pieces. PMID:25475312

  16. Cross contamination of Escherichia coli O157:H7 between lettuce and wash water during home-scale washing.

    PubMed

    Jensen, Dane A; Friedrich, Loretta M; Harris, Linda J; Danyluk, Michelle D; Schaffner, Donald W

    2015-04-01

    Lettuce and leafy greens have been implicated in multiple foodborne disease outbreaks. This study quantifies cross contamination between lettuce pieces in a small-scale home environment. A five-strain cocktail of relevant Escherichia coli O157:H7 strains was used. Bacterial transfer between single inoculated lettuce leaf pieces to 10 non-inoculated lettuce leaf pieces that were washed in a stainless steel bowl of water for 30 s, 1 min, 2 min, and 5 min was quantified. Regardless of washing time, the wash water became contaminated with 90-99% of bacteria originally present on the inoculated lettuce leaf piece. The E. coli O157:H7 concentration on initially inoculated leaf pieces was reduced ∼ 2 log CFU. Each initially uncontaminated lettuce leaf piece had ∼ 1% of the E. coli O157:H7 from the inoculated lettuce piece transferred to it after washing, with more transfer occurring during the shortest (30 s) and longest (5 min) wash times. In all cases the log percent transfer rates were essentially normally distributed. In all scenarios, most of the E. coli O157:H7 (90-99%) transferred from the inoculated lettuce pieces to the wash water. Washing with plain tap water reduces levels of E. coli O157:H7 on the inoculated lettuce leaf pieces, but also spreads contamination to previously uncontaminated leaf pieces.

  17. Experimental hut comparisons of nets treated with carbamate or pyrethroid insecticides, washed or unwashed, against pyrethroid-resistant mosquitoes.

    PubMed

    Asidi, A N; N'Guessan, R; Hutchinson, R A; Traoré-Lamizana, M; Carnevale, P; Curtis, C F

    2004-06-01

    The efficacy against mosquitoes (Diptera: Culicidae) of a bednet treated with carbamate insecticide [carbosulfan capsule suspension (CS) 200 mg/m(2)] was compared with four types of pyrethroid-treated nets in veranda-trap huts at Yaokoffikro near Bouaké, Côte d'Ivoire, where the malaria vector Anopheles gambiae Giles carries the kdr gene (conferring pyrethroid resistance) at high frequency and Culex quinquefasciatus Say is also pyrethroid resistant. Pyrethroids compared were lambdacyhalothrin CS 18 mg/m(2), alphacypermethrin water dispersible granules (WG) 20 mg/m(2), deltamethrin 50 mg/m(2) (Permanet) and permethrin emulsifiable concentrate (EC) 500 mg/m(2). Insecticidal power and personal protection from mosquito bites were assessed before and after the nets were used for 8 months and hand washed five times in cold soapy water. Before washing, all treatments except permethrin significantly reduced blood-feeding and all had significant insecticidal activity against An. gambiae. The carbosulfan net gave significantly higher killing of An. gambiae than all pyrethroid treatments except the Permanet. Against Culex spp., carbosulfan was more insecticidal and gave a significantly better protective effect than any of the pyrethroid treatments. After washing, treated nets retained various degrees of efficacy against both mosquito genera - but least for the carbosulfan net. Washed nets with three types of pyrethroid treatment (alphacypermethrin, lambdacyhalothrin, permethrin) gave significantly higher mortality rates of Culex than in huts with the same pyrethroid-treated nets before washing. After five washes, the Permanet, which is sold as a long-lasting insecticidal product, performed no better than the other nets in our experimental conditions.

  18. Reliability and Validity of the SE-HEPA: Examining Physical Activity- and Healthy Eating-Specific Self-Efficacy among a Sample of Preadolescents

    ERIC Educational Resources Information Center

    Steele, Michael M.; Burns, Leonard G.; Whitaker, Brandi N.

    2013-01-01

    Objective. The purpose of this study was to examine the psychometric properties of the self-efficacy for healthy eating and physical activity measure (SE-HEPA) for preadolescents. Method. The reliability of the measure was examined to determine if the internal consistency of the measure was adequate (i.e., [alpha]s greater than 0.70). Next, in an…

  19. Interactions of endosulfan and methoxychlor involving CYP3A4 and CYP2B6 in human HepaRG cells.

    PubMed

    Savary, Camille C; Jossé, Rozenn; Bruyère, Arnaud; Guillet, Fabrice; Robin, Marie-Anne; Guillouzo, André

    2014-08-01

    Humans are usually exposed to several pesticides simultaneously; consequently, combined actions between pesticides themselves or between pesticides and other chemicals need to be addressed in the risk assessment. Many pesticides are efficient activators of pregnane X receptor (PXR) and/or constitutive androstane receptor (CAR), two major nuclear receptors that are also activated by other substrates. In the present work, we searched for interactions between endosulfan and methoxychlor, two organochlorine pesticides whose major routes of metabolism involve CAR- and PXR-regulated CYP3A4 and CYP2B6, and whose mechanisms of action in humans remain poorly understood. For this purpose, HepaRG cells were treated with both pesticides separately or in mixture for 24 hours or 2 weeks at concentrations relevant to human exposure levels. In combination they exerted synergistic cytotoxic effects. Whatever the duration of treatment, both compounds increased CYP3A4 and CYP2B6 mRNA levels while differently affecting their corresponding activities. Endosulfan exerted a direct reversible inhibition of CYP3A4 activity that was confirmed in human liver microsomes. By contrast, methoxychlor induced this activity. The effects of the mixture on CYP3A4 activity were equal to the sum of those of each individual compound, suggesting an additive effect of each pesticide. Despite CYP2B6 activity being unchanged and increased with endosulfan and methoxychlor, respectively, no change was observed with their mixture, supporting an antagonistic effect. Altogether, our data suggest that CAR and PXR activators endosulfan and methoxychlor can interact together and with other exogenous substrates in human hepatocytes. Their effects on CYP3A4 and CYP2B6 activities could have important consequences if extrapolated to the in vivo situation.

  20. Automated detection of hepatotoxic compounds in human hepatocytes using HepaRG cells and image-based analysis of mitochondrial dysfunction with JC-1 dye

    SciTech Connect

    Pernelle, K.; Le Guevel, R.; Glaise, D.; Stasio, C. Gaucher-Di; Le Charpentier, T.; Bouaita, B.; Corlu, A.; Guguen-Guillouzo, C.

    2011-08-01

    In this study, our goal was to develop an efficient in situ test adapted to screen hepatotoxicity of various chemicals, a process which remains challenging during the early phase of drug development. The test was based on functional human hepatocytes using the HepaRG cell line, and automation of quantitative fluorescence microscopy coupled with automated imaging analysis. Differentiated HepaRG cells express most of the specific liver functions at levels close to those found in primary human hepatocytes, including detoxifying enzymes and drug transporters. A triparametric analysis was first used to evaluate hepatocyte purity and differentiation status, mainly detoxication capacity of cells before toxicity testing. We demonstrated that culturing HepaRG cells at high density maintained high hepatocyte purity and differentiation level. Moreover, evidence was found that isolating hepatocytes from 2-week-old confluent cultures limited variations associated with an ageing process occurring over time in confluent cells. Then, we designed a toxicity test based on detection of early mitochondrial depolarisation associated with permeability transition (MPT) pore opening, using JC-1 as a metachromatic fluorescent dye. Maximal dye dimerization that would have been strongly hampered by efficient efflux due to the active, multidrug-resistant (MDR) pump was overcome by coupling JC-1 with the MDR inhibitor verapamil. Specificity of this test was demonstrated and its usefulness appeared directly dependent on conditions supporting hepatic cell competence. This new hepatotoxicity test adapted to automated, image-based detection should be useful to evaluate the early MPT event common to cell apoptosis and necrosis and simultaneously to detect involvement of the multidrug resistant pump with target drugs in a human hepatocyte environment. - Highlights: > We define conditions to preserve differentiation of selective pure HepaRG hepatocyte cultures. > In these conditions, CYPs

  1. Efficacy of low-concentration iodophors for germicidal hand washing.

    PubMed Central

    Stiles, M. E.; Sheena, A. Z.

    1985-01-01

    The efficacy of iodophor germicides containing different concentrations of available iodine against transient (inoculated) bacteria and the natural hand microflora was compared with chlorhexidine gluconate (2 and 4%) liquid detergent (Hibitane), non-germicidal soap and a tap water rinse. The tap water rinse was ineffective compared with all other treatments. Only 4% chlorhexidine gluconate liquid detergent and iodophor containing 0.75% available iodine were significantly better than the non-germicidal soap for reduction of transient bacteria, Escherichia coli and Pseudomonas fluorescens, that had been inoculated onto hands. These agents also caused a significant reduction in the number of 'natural' microorganisms released from hands after a standard 15 s hand wash. The low-concentration iodophor products and the product containing 2% chlorhexidine gluconate failed to give results significantly better than the non-germicidal control soap. Baird-Parker medium and standard aerobic plate counts were highly correlated (r = 0.82), so that for studies of Gram-negative bacteria inoculated onto hands as a transient microflora, counts on Baird-Parker medium give a reasonable indication of the natural (residual) hand microflora. PMID:3924994

  2. Soil Washing Experiment for Decontamination of Contaminated NPP Soil

    SciTech Connect

    Son, J.K.; Kang, K.D.; Kim, K.D.; Ha, J.H.; Song, M.J.

    2006-07-01

    The preliminary experiment was performed to obtain the operating conditions of soil washing decontamination process such as decontamination agent, decontamination temperature, decontamination time and ratio of soil and decontamination agent. To estimate decontamination efficiency, particle size of soil was classified into three categories; {>=} 2.0 mm, 2.0 {approx} 0.21 mm and {<=} 0.21 mm. Major target of this experiment was decontamination of Cs-137. The difference of decontamination efficiency using water and neutral salts as decontamination agent is not high. It is concluded that the best temperature of decontamination agent is normal temperature and the best decontamination time was about 60 minutes. And the best ratio of soil and decontamination agent is 1:10. In case of Cs decontamination for fine soils, the decontamination results using neutral salts such as Na{sub 2}CO{sub 3} and Na{sub 3}PO{sub 4} shows some limits while using strong acid such as sulfuric acid or hydrochloric acid shows high decontamination efficiency ({>=}90%). But we conclude that decontamination using strong acid is also inappropriate because of the insufficiency of decontamination efficiency for highly radioactive fine soils and the difficulty for treatment of secondary liquid waste. It is estimated that the best decontamination process is to use water as decontamination agent for particles which can be decontaminated to clearance level, after particle size separation. (authors)

  3. Washing off intensification of cotton and wool fabrics by ultrasounds.

    PubMed

    Peila, R; Actis Grande, G; Giansetti, M; Rehman, S; Sicardi, S; Rovero, G

    2015-03-01

    Wet textile washing processes were set up for wool and cotton fabrics to evaluate the potential of ultrasound transducers (US) in improving dirt removal. The samples were contaminated with an emulsion of carbon soot in vegetable oil and aged for three hours in fan oven. Before washing, the fabrics were soaked for 3 min in a standard detergent solution and subsequently washed in a water bath. The dirt removal was evaluated through colorimetric measurements. The total color differences ΔE of the samples were measured with respect to an uncontaminated fabric, before and after each washing cycle. The percentage of ΔE variation obtained was calculated and correlated to the dirt removal. The results showed that the US transducers enhanced the dirt removal and temperature was the parameter most influencing the US efficiency on the cleaning process. Better results were obtained at a lower process temperature.

  4. Being washed by someone is therapeutic... and a treat.

    PubMed

    Winterflood, Florence

    2014-08-26

    When in Istanbul, I visited a hamam, a traditional Turkish bath. I'm familiar with other bathing rituals--steam room, sauna, Jacuzzi--but suspected being washed by someone in front of others was not very British.

  5. 11. VIEW LOOKING OUT UPPER LEVEL WINDOW OF WASH HOUSE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    11. VIEW LOOKING OUT UPPER LEVEL WINDOW OF WASH HOUSE SHOWING SLACK COAL STORAGE TANK - Kaymoor Coal Mine, South side of New River, upstream of New River Gorge Bridge, Fayetteville, Fayette County, WV

  6. 30 CFR 1206.458 - Determination of washing allowances.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... INTERIOR Natural Resources Revenue PRODUCT VALUATION Indian Coal § 1206.458 Determination of washing... bearing. (c) Reporting requirements—(1) Arm's-length contracts. (i) With the exception of those...

  7. 30 CFR 1206.259 - Determination of washing allowances.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... INTERIOR Natural Resources Revenue PRODUCT VALUATION Federal Coal § 1206.259 Determination of washing... not royalty bearing. (c) Reporting requirements—(1) Arm's-length contracts. (i) The lessee must...

  8. 38. Photocopy of ink and wash rendering by N. G. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    38. Photocopy of ink and wash rendering by N. G. Starkwether in collection of Mr. & Mrs. Richard T. Pratt, Camden REAR ELEVATION OF W. C. PRATT'S COUNTRY SEAT - Camden, Rappahannock River, Port Royal, Caroline County, VA

  9. 17. Photocopy of circa 1839 ink and wash drawing by ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    17. Photocopy of circa 1839 ink and wash drawing by Richard Upjohn in Avery Library, Columbia University, New York, New York FRONT ELEVATION (below) AND REAR ELEVATION (above) - Kingscote, Bellevue Avenue & Bowery Street, Newport, Newport County, RI

  10. 20. Photocopy of ink and wash drawing by Richard Upjohn, ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    20. Photocopy of ink and wash drawing by Richard Upjohn, circa 1839, in Avery Library, Columbia University FIRST AND SECOND FLOOR PLANS - Kingscote, Bellevue Avenue & Bowery Street, Newport, Newport County, RI

  11. 19. Photocopy of circa 1839 ink and wash drawing by ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    19. Photocopy of circa 1839 ink and wash drawing by Richard Upjohn in Avery Library, Columbia University EAST ELEVATION (above) AND SECOND-FLOOR PLAN (below) - Kingscote, Bellevue Avenue & Bowery Street, Newport, Newport County, RI

  12. [The effectiveness of ozonated water for hand washing before surgery].

    PubMed

    Isosu, T; Kan, K; Hayashi, T; Fujii, M

    2001-06-01

    Using an ozonated water-dispensing machine for sterilization of hands (Mediaqua MA-III; Core Medical Co., Ltd, Tokyo, Japan), we investigated the effectiveness of ozonated water as a disinfectant for hand washing before surgery. The effectiveness of this new hand-washing method, using 4 ppm of ozonated water, which is expected to have a short-term bactericidal effect, and 0.2% benzalkonium chloride/83% ethanol solution (Welpas), which is expected to have a long-term bactericidal effect, was compared with that of the conventional hand-washing method (Fürbringer's method using a scrubbing agent containing povidone-iodine). The results showed no significant differences in the numbers of live bacteria and exponential reduction rates in live bacteria. Thus, this new method for hand washing using ozonated water is an effective method for sterilization of the hands before surgery.

  13. 37. Photocopy of ink and wash rendering by N. G. ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    37. Photocopy of ink and wash rendering by N. G. Starkwether in collection of Mr. & Mrs. Richard T. Pratt, Camden SIDE ELEVATION OF ITALIAN VILLA FOR W. C. PRATT, ESQr - Camden, Rappahannock River, Port Royal, Caroline County, VA

  14. Documentation of a decision framework to support enhanced sludge washing

    SciTech Connect

    Brothers, A.J.

    1995-12-31

    This document describes a proposed decision model that, if developed to its fullest, can provide a wide range of analysis options and insights to pretreatment/sludge washing alternatives. A recent decision has been made to terminate this work

  15. Appraisal of guidelines for pre-operative body wash.

    PubMed

    Edström, Elisabet; Westerberg, Lisa; Henricson, Maria

    The pre-operative body wash is a strategy for reducing post-operative infection. However, there is a lack of knowledge about its importance. The purpose of the present study was to evaluate the quality of guidelines for the pre-operative body wash using the AGREE instrument--35 guidelines containing instructions for the pre-operative body wash or preparation were included. The AGREE instrument was employed to establish a quality assessment framework that facilitated a comparison of the guidelines. The results were based on the six domains of the AGREE instrument, all of which were found to have low adherence. Descriptive statistics were used to present the assessment score. The AGREE instrument is useful for evaluating the quality of clinical guidelines. The development of evidence-based guidelines must include clinical activities. Further research is required to clarify the pre-operative body wash process and how it should be performed to reduce post-operative infection. PMID:25426523

  16. Control of helminth contamination of raw vegetables by washing.

    PubMed

    Avcioğlu, Hamza; Soykan, Emel; Tarakci, Umit

    2011-02-01

    This study was conducted to determine the control of helminth egg contamination of raw vegetables by washing. A total of 199 unwashed and 199 washed lettuce, parsley, carrots, dill, rocket, and green-peppers, provided by a catering service in Bursa, Turkey, between March and June 2009, were subjected to helminth egg count under light microscopy. Helminth eggs were detected in six (3.0%) unwashed samples and not in any washed samples (p<0.01). Ascaris lumbricoides and Toxocara spp. were detected in four (2.0%) and two (1.0%) unwashed vegetables, respectively, mostly among leafy vegetables such as lettuce and parsley. Our data confirm that washing procedures before consumption of raw vegetables regardless of the providers' sanitation should be performed to avoid transmission of helminths. PMID:20569015

  17. PARTS WASHING ALTERNATIVES STUDY - UNITED STATES COAST GUARD

    EPA Science Inventory

    This report has been written to assist the United States Coast Guard (USCG) industrial managers in determining the most cost effective and environmentally acceptable parts washing alternatives for their specific applications. An; evaluation was conducted on four different cleane...

  18. SOIL WASHING TREATABILITY TESTS FOR PESTICIDE- CONTAMINATED SOIL

    EPA Science Inventory

    The 1987 Sand Creek Operable Unit 5 record of decision (ROD) identified soil washing as the selected technology to remediate soils contaminated with high levels of organochlorine pesticides, herbicides, and metals. Initial treatability tests conducted to assess the applicability...

  19. 7. CLOSEUP VIEW OF WASHED UP 12' x 12' DAM ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    7. CLOSE-UP VIEW OF WASHED UP 12' x 12' DAM SUPPORT TIMBERS, THREE BEARS LAKE, LOOKING NORTHEAST FROM SOUTH SIDE OF LAKE - Three Bears Lake & Dams, North of Marias Pass, East Glacier Park, Glacier County, MT

  20. 6. VIEW OF THREE BEARS LAKE, SHOWING WASHED UP 12' ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    6. VIEW OF THREE BEARS LAKE, SHOWING WASHED UP 12' x 12' DAM SUPPORT TIMBERS, LOOKING NORTHEAST FROM SOUTH SIDE OF LAKE - Three Bears Lake & Dams, North of Marias Pass, East Glacier Park, Glacier County, MT

  1. Why Is Hand Washing So Important? (For Parents)

    MedlinePlus

    ... Family Campylobacter Infections Hand, Foot, and Mouth Disease MRSA Food Poisoning Diarrhea Tips From School Nurses on ... Hands Without Spreading Germs? Hand Washing Staph Infections MRSA Flu Facts Why Should I Care About Germs? ...

  2. View of Steel Flume Bridge #2 crossing over wash. Looking ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    View of Steel Flume Bridge #2 crossing over wash. Looking downstream, southwest - Childs-Irving Hydroelectric Project, Childs System, Flume Bridge No. 2, Forest Service Road 708/502, Camp Verde, Yavapai County, AZ

  3. Enhanced antimicrobial effect of organic acid washing against foodborne pathogens on broccoli by vacuum impregnation.

    PubMed

    Kang, Jun-Won; Kang, Dong-Hyun

    2016-01-18

    This study was undertaken to evaluate the effect of vacuum impregnation applied to the washing process for removal of Salmonella Typhimurium and Listeria monocytogenes from broccoli surfaces. Broccoli was inoculated with the two foodborne pathogens and treated with simple dipping washing or with vacuum impregnation in 2% malic acid for 5, 10, 20, or 30 min. There were two methods of vacuum impregnation: continuous and intermittent. After 30 min of 101.3 kPa (=14.7 psi, simple dipping), 61.3 kPa (=8.9 psi), and 21.3 kPa (=3.1 psi) of continuous vacuum impregnation treatment, there were 1.6, 2.0, and 2.4 log 10 CFU/g reductions of S. Typhimurium and 1.5, 1.7, and 2.3 log 10 CFU/g reductions of L. monocytogenes, respectively. After 30 min of 101.3, 61.3, and 21.3 kPa of intermittent vacuum impregnation treatment, there were 1.5, 2.3, and 3.7 log 10 CFU/g reductions of S. Typhimurium and 1.6, 2.1, and 3.2 log 10 CFU/g reductions of L. monocytogenes, respectively. Scanning electron photomicrographs showed that bacteria tend to attach to or become entrapped in protective sites after simple wash processing (dipping). However, most bacteria were washed out of protective sites after intermittent treatment. Direct treatment of cell suspensions with vacuum impregnation showed that it had no inactivation capacity in itself since there were no significant differences (P ≥ 0.05) between the reduction rates of non- and vacuum impregnation treatment. These results demonstrate that the increased antimicrobial effect of vacuum impregnation can be attributed to increased accessibility of sanitizer and an enhanced washing effect in protected sites on produce. Color, texture and titratable acidity values of broccoli treated with intermittent vacuum impregnation in 2% malic acid for 30 min were not significantly (P ≥ 0.05) different from those of untreated samples even though a storage interval was needed for titratable acidity values to be reduced to levels comparable to those of

  4. Enhanced antimicrobial effect of organic acid washing against foodborne pathogens on broccoli by vacuum impregnation.

    PubMed

    Kang, Jun-Won; Kang, Dong-Hyun

    2016-01-18

    This study was undertaken to evaluate the effect of vacuum impregnation applied to the washing process for removal of Salmonella Typhimurium and Listeria monocytogenes from broccoli surfaces. Broccoli was inoculated with the two foodborne pathogens and treated with simple dipping washing or with vacuum impregnation in 2% malic acid for 5, 10, 20, or 30 min. There were two methods of vacuum impregnation: continuous and intermittent. After 30 min of 101.3 kPa (=14.7 psi, simple dipping), 61.3 kPa (=8.9 psi), and 21.3 kPa (=3.1 psi) of continuous vacuum impregnation treatment, there were 1.6, 2.0, and 2.4 log 10 CFU/g reductions of S. Typhimurium and 1.5, 1.7, and 2.3 log 10 CFU/g reductions of L. monocytogenes, respectively. After 30 min of 101.3, 61.3, and 21.3 kPa of intermittent vacuum impregnation treatment, there were 1.5, 2.3, and 3.7 log 10 CFU/g reductions of S. Typhimurium and 1.6, 2.1, and 3.2 log 10 CFU/g reductions of L. monocytogenes, respectively. Scanning electron photomicrographs showed that bacteria tend to attach to or become entrapped in protective sites after simple wash processing (dipping). However, most bacteria were washed out of protective sites after intermittent treatment. Direct treatment of cell suspensions with vacuum impregnation showed that it had no inactivation capacity in itself since there were no significant differences (P ≥ 0.05) between the reduction rates of non- and vacuum impregnation treatment. These results demonstrate that the increased antimicrobial effect of vacuum impregnation can be attributed to increased accessibility of sanitizer and an enhanced washing effect in protected sites on produce. Color, texture and titratable acidity values of broccoli treated with intermittent vacuum impregnation in 2% malic acid for 30 min were not significantly (P ≥ 0.05) different from those of untreated samples even though a storage interval was needed for titratable acidity values to be reduced to levels comparable to those of

  5. Assessment and optimization of an ultrasound-assisted washing process using organic solvents for polychlorinated biphenyl-contaminated soil.

    PubMed

    Bezama, Alberto; Flores, Alejandra; Araneda, Alberto; Barra, Ricardo; Pereira, Eduardo; Hernández, Víctor; Moya, Heriberto; Konrad, Odorico; Quiroz, Roberto

    2013-10-01

    The goal of this work was to evaluate a washing process that uses organic solutions for polychlorinated biphenyl (PCB)-contaminated soil, and includes an ultrasound pre-treatment step to reduce operational times and organic solvent losses. In a preliminary trial, the suitability of 10 washing solutions of different polarities were tested, from which three n-hexane-based solutions were selected for further evaluation. A second set of experiments was designed using a three-level Taguchi L27 orthogonal array to model the desorption processes of seven different PCB congeners in terms of the variability of their PCB concentration levels, polarity of the washing solution, sonication time, the ratio washing solution/soil, number of extraction steps and total washing time. Linear models were developed for the desorption processes of all congeners. These models provide a good fit with the results obtained. Moreover, statistically significant outcomes were achieved from the analysis of variance tests carried out. It was determined that sonication time and ratio of washing solution/soil were the most influential process parameters. For this reason they were studied in a third set of experiments, constructed as a full factorial design. The process was eventually optimized, achieving desorption rates of more than 90% for all congeners, thus obtaining concentrations lower than 5 ppb in all cases. The use of an ultrasound-assisted soil washing process for PCB-contaminated soils that uses organic solvents seems therefore to be a viable option, especially with the incorporation of an extra step in the sonication process relating to temperature control, which is intended to prevent the loss of the lighter congeners.

  6. Immunotoxicity of washing soda in a freshwater sponge of India.

    PubMed

    Mukherjee, Soumalya; Ray, Mitali; Ray, Sajal

    2015-03-01

    The natural habitat of sponge, Eunapius carteri faces an ecotoxicological threat of contamination by washing soda, a common household cleaning agent of India. Washing soda is chemically known as sodium carbonate and is reported to be toxic to aquatic organisms. Domestic effluent, drain water and various human activities in ponds and lakes have been identified as the major routes of washing soda contamination of water. Phagocytosis and generation of cytotoxic molecules are important immunological responses offered by the cells of sponges against environmental toxins and pathogens. Present study involves estimation of phagocytic response and generation of cytotoxic molecules like superoxide anion, nitric oxide and phenoloxidase in E. carteri under the environmentally realistic concentrations of washing soda. Sodium carbonate exposure resulted in a significant decrease in the phagocytic response of sponge cells under 4, 8, 16 mg/l of the toxin for 96h and all experimental concentrations of the toxin for 192h. Washing soda exposure yielded an initial increase in the generation of the superoxide anion and nitric oxide followed by a significant decrease in generation of these cytotoxic agents. Sponge cell generated a high degree of phenoloxidase activity under the experimental exposure of 2, 4, 8, 16 mg/l of sodium carbonate for 96 and 192 h. Washing soda induced alteration of phagocytic and cytotoxic responses of E. carteri was indicative to an undesirable shift in their immune status leading to the possible crises of survival and propagation of sponges in their natural habitat.

  7. Induced phytoextraction/soil washing of lead using biodegradable chelate and permeable barriers.

    PubMed

    Kos, Bostjan; Lestan, Domen

    2003-02-01

    Chelate-induced remediation has been proposed as an effective tool for the extraction of lead (Pb) from contaminated soils by plants. However, side-effects, mainly mobilization and leaching of Pb, raise environmental concerns. Biodegradable, synthetic organic chelate ethylenediaminedisuccinic acid (EDDS), and commonly used ethylenedimanetetraacetic acid (EDTA) were used for induced phytoextraction with a test plant Brassica rapa and in situ washing of soil contaminated with 1350 mg/kg of Pb. Horizontal permeable barriers were placed 20 cm deep in soil columns and tested for their ability to prevent leaching of Pb. The reactive materials in the barriers were nutrient enriched vermiculite, peat or agricultural hydrogel, and apatite. EDTA and EDDS addition increased Pb concentrations in the test plant by 158 and 89 times compared to the control, to 817 and 464 mg/kg, respectively. In EDTA treatments, approximately 25% or more of total initial soil Pb was leached in single cycle of chelate addition. In EDDS treatments, 20% of the initial Pb was leached from columns with no barrier, while barriers with vermiculite or hydrogel and apatite decreased leaching by more than 60 times, to 0.35%. 11.6% of total initial Pb was washed from the soil above the barrier with vermiculite and apatite, where almost all leached Pb was accumulated. Results indicate that use of biodegradable chelate EDDS and permeable barriers may lead to environmentally safe induced Pb phytoextraction and in situ washing of Pb.

  8. Pollutant removal from oily wastewater discharged from car washes through sedimentation-coagulation.

    PubMed

    Rubí, H; Fall, C; Ortega, R E

    2009-01-01

    Wastewater from car washes represents a potential problem for the sewer system due to its emulsified oils and suspended material. Treatment of wastewater discharged from four car washes was investigated by sedimentation and coagulation. The effect of the coagulants Servical P (aluminium hydroxychloride), Servican 50 (poly(diallyldimethylammonium chloride)), aluminium sulfate and ferric chloride was evaluated. The achieved removal using sedimentation was of 82%, 88% 73% and 51% for oils, total suspended solids, COD, and turbidity, respectively. In the treatment by coagulation we achieved average efficiencies nearly to 74% for COD removal, greater than 88% in the case of total suspended solids removal and 92% in the case of turbidity and except the performance of Servican 50 greater than 90% in oil removal. We concluded that the oil residual concentration and COD in the treated water allows pouring it in the sewer system complying with the limits of the Mexican rule NOM-002-ECOL-1996 and it is possible even its reuse, at least in the case of the chassis washing of cars. PMID:19542641

  9. Pollutant removal from oily wastewater discharged from car washes through sedimentation-coagulation.

    PubMed

    Rubí, H; Fall, C; Ortega, R E

    2009-01-01

    Wastewater from car washes represents a potential problem for the sewer system due to its emulsified oils and suspended material. Treatment of wastewater discharged from four car washes was investigated by sedimentation and coagulation. The effect of the coagulants Servical P (aluminium hydroxychloride), Servican 50 (poly(diallyldimethylammonium chloride)), aluminium sulfate and ferric chloride was evaluated. The achieved removal using sedimentation was of 82%, 88% 73% and 51% for oils, total suspended solids, COD, and turbidity, respectively. In the treatment by coagulation we achieved average efficiencies nearly to 74% for COD removal, greater than 88% in the case of total suspended solids removal and 92% in the case of turbidity and except the performance of Servican 50 greater than 90% in oil removal. We concluded that the oil residual concentration and COD in the treated water allows pouring it in the sewer system complying with the limits of the Mexican rule NOM-002-ECOL-1996 and it is possible even its reuse, at least in the case of the chassis washing of cars.

  10. Natural attenuation of NDMA precursors in an urban, wastewater-dominated wash.

    PubMed

    Woods, Gwen C; Dickenson, Eric R V

    2016-02-01

    N-Nitrosodimethylamine (NDMA) is a disinfection by-product (DBP) that is potentially carcinogenic and has been found to occur in drinking water treatment systems impacted with treated wastewater. A major gap in NDMA research is an understanding of the persistence of wastewater-derived precursors within the natural environment. This research sought to fill this knowledge gap by surveying NDMA precursors across the length of a wastewater effluent-dominated wash. Significant precursor reduction (17%) was found to occur from introduction into the wash to a point 9 h downstream. This reduction translates into a half-life of roughly 32 h for bulk NDMA precursors. Further laboratory experiments examining rates of photolysis, biodegradation and loss to sediments, illustrated that both photolytic and biological degradation were effective removal mechanisms for NDMA precursors. Loss to sediments that were acquired from the wash did not appear to reduce NDMA precursors in the water column, although a control conducted with DI water provided evidence that significant NDMA precursors could be released from autoclaved sediments (suggesting that sorption does occur). Microbial experiments revealed that microbes associated with sediments were much more effective at degrading precursors than microbes within the water column. Overall, this study demonstrated that natural processes are capable of attenuating NDMA precursors relatively quickly within the environment, and that utilities might benefit from maximizing source water residency time in the environment, prior to introduction into treatment plants.

  11. Extraction agents for the removal of polycyclic aromatic hydrocarbons (PAHs) from soil in soil washing technologies.

    PubMed

    Lau, Ee Von; Gan, Suyin; Ng, Hoon Kiat; Poh, Phaik Eong

    2014-01-01

    Polycyclic aromatic hydrocarbons (PAHs) in soil have been recognised as a serious health and environmental issue due to their carcinogenic, mutagenic and teratogenic properties. One of the commonly employed soil remediation techniques to clean up such contamination is soil washing or solvent extraction. The main factor which governs the efficiency of this process is the solubility of PAHs in the extraction agent. Past field-scale soil washing treatments for PAH-contaminated soil have mainly employed organic solvents or water which is either toxic and costly or inefficient in removing higher molecular weight PAHs. Thus, the present article aims to provide a review and discussion of the alternative extraction agents that have been studied, including surfactants, biosurfactants, microemulsions, natural surfactants, cyclodextrins, vegetable oil and solution with solid phase particles. These extraction agents have been found to remove PAHs from soil at percentages ranging from 47 to 100% for various PAHs. PMID:24100092

  12. Differential regulation of polysome mRNA levels in mouse Hepa-1C1C7 cells exposed to dioxin.

    PubMed

    Thornley, Jessica A; Trask, Heidi W; Ridley, Christian J A; Korc, Murray; Gui, Jiang; Ringelberg, Carol S; Wang, Sinny; Tomlinson, Craig R

    2011-10-01

    The environmental agent 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD or dioxin) causes a multitude of human illnesses. In order to more fully understand the underlying biology of TCDD toxicity, we tested the hypothesis that new candidate genes could be identified using polysome RNA from TCDD-treated mouse Hepa-1c1c7 cells. We found that (i) differentially expressed whole cell and cytoplasm RNA levels are both poor predictors of polysome RNA levels; (ii) for a majority of RNAs, differential RNA levels are regulated independently in the nucleus, cytoplasm, and polysomes; (iii) for the remaining polysome RNAs, levels are regulated via several different mechanisms, including a "tagging" of mRNAs in the nucleus for immediate polysome entry; and (iv) most importantly, a gene list derived from differentially expressed polysome RNA generated new genes and cell pathways potentially related to TCDD biology.

  13. The Impacts of Traffic-Related and Woodsmoke Particulate Matter on Measures of Cardiovascular Health: A HEPA Filter Intervention Study

    PubMed Central

    Kajbafzadeh, Majid; Brauer, Michael; Karlen, Barbara; Carlsten, Chris; van Eeden, Stephan; Allen, Ryan W.

    2016-01-01

    Background Combustion-generated fine particulate matter (PM2.5) is associated with cardiovascular morbidity. Both traffic-related air pollution and residential wood combustion may be important, but few studies have compared their impacts. Objectives To assess and compare effects of traffic-related and woodsmoke PM2.5 on endothelial function and systemic inflammation (C-reactive protein, interleukin-6, and band cells) among healthy adults in Vancouver, British Columbia, Canada using high efficiency particulate air (HEPA) filtration to introduce indoor PM2.5 exposure gradients. Methods We recruited 83 healthy adults from 44 homes in traffic- or woodsmoke-impacted areas to participate in this randomized, single-blind crossover intervention study. PM2.5 concentrations were measured during two consecutive 7-day periods, one with filtration and the other with “placebo filtration”. Endothelial function and biomarkers of systematic inflammation were measured at the end of each 7-day period. Results HEPA filtration was associated with a 40% decrease in indoor PM2.5 concentrations. There was no relationship between PM2.5 exposure and endothelial function. There was evidence of an association between indoor PM2.5 and C-reactive protein among those in traffic-impacted locations [42.1% increase in C-reactive protein per interquartile range increase in indoor PM2.5, 95% CI, 1.2 to 99.5] but not among those in woodsmoke-impacted locations. There were no associations with interleukin-6 or band cells. Conclusions Evidence of an association between C-reactive protein and indoor PM2.5 among healthy adults in traffic-impacted areas is consistent with the hypothesis that traffic-related particles, even at relatively low concentrations, play an important role in the cardiovascular effects of the urban PM mixture. Trial registered at www.clinicaltrials.gov (NCT01570062) PMID:25896330

  14. HepaRG microencapsulated spheroids in DMSO-free culture: novel culturing approaches for enhanced xenobiotic and biosynthetic metabolism.

    PubMed

    Rebelo, Sofia P; Costa, Rita; Estrada, Marta; Shevchenko, Valery; Brito, Catarina; Alves, Paula M

    2015-08-01

    The need for models that recapitulate liver physiology is perceived for drug development, study of liver disease and bioartificial liver support. The bipotent cell line HepaRG constitutes an efficient surrogate of liver function, yet its differentiated status relies on high concentrations of DMSO, which may compromise the study of drug metabolism and limit the applicability of this hepatic model. Herein, we present a three-dimensional (3D) strategy for the differentiation of HepaRG based on alginate microencapsulation of cell spheroids and culture in dimethyl sulfoxide (DMSO)-free conditions. A ratio of 2.9:1 hepatocyte-like to biliary-like cells was obtained in the 3D culture, with an improvement of 35.9 % in the hepatocyte differentiation when compared with two-dimensional (2D) cultures. The expression of the hepatic identity genes HNF4α and PXR in 3D cultures was comparable to 2D differentiated cultures, while the expression of homeostatic-associated genes albumin and carbamoyl phosphate synthase 1 was higher in 3D. Moreover, the spheroids presented a polarized organization, exhibiting an interconnected bile canalicular network and excretory functionality, assessed by specific activity of MRP2. Importantly, despite variability in basal gene expression levels, the activity of the phase I enzymes cytochrome P450 family 3, subfamily A, polypeptide 4 and cytochrome P450 family 1, subfamily A, polypeptide 2 upon induction was comparable to differentiated 2D cultures and albumin production and ammonia detoxification were enhanced in 3D. The presented model is suitable for toxicological applications, as it allows high throughput analysis of multiple compounds in a DMSO-free setting. Due to the high xenobiotic metabolism and maintenance of biosynthetic functions, the applicability of this model might be broadened to understand liver physiology and for bioartificial liver applications. PMID:25107451

  15. EBR-II Primary Tank Wash-Water Alternatives Evaluation

    SciTech Connect

    Demmer, R. L.; Heintzelman, J. B.; Merservey, R. H.; Squires, L. N.

    2008-05-01

    The EBR-II reactor at Idaho National Laboratory was a liquid sodium metal cooled reactor that operated for 30 years. It was shut down in 1994; the fuel was removed by 1996; and the bulk of sodium metal coolant was removed from the reactor by 2001. Approximately 1100 kg of residual sodium remained in the primary system after draining the bulk sodium. To stabilize the remaining sodium, both the primary and secondary systems were treated with a purge of moist carbon dioxide. Most of the residual sodium reacted with the carbon dioxide and water vapor to form a passivation layer of primarily sodium bicarbonate. The passivation treatment was stopped in 2005 and the primary system is maintained under a blanket of dry carbon dioxide. Approximately 670 kg of sodium metal remains in the primary system in locations that were inaccessible to passivation treatment or in pools of sodium that were too deep for complete penetration of the passivation treatment. The EBR-II reactor was permitted by the Idaho Department of Environmental Quality (DEQ) in 2002 under a RCRA permit that requires removal of all remaining sodium in the primary and secondary systems by 2022. The proposed baseline closure method would remove the large components from the primary tank, fill the primary system with water, react the remaining sodium with the water and dissolve the reaction products in the wash water. This method would generate a minimum of 100,000 gallons of caustic, liquid, low level radioactive, hazardous waste water that must be disposed of in a permitted facility. On February 19-20, 2008, a workshop was held in Idaho Falls, Idaho, to look at alternatives that could meet the RCRA permit clean closure requirements and minimize the quantity of hazardous waste generated by the cleanup process. The workshop convened a panel of national and international sodium cleanup specialists, subject matter experts from the INL, and the EBR-II Wash Water Project team that organized the workshop. The

  16. The potential impact of washing machines on laundry malodour generation.

    PubMed

    Stapleton, K; Hill, K; Day, K; Perry, J D; Dean, J R

    2013-04-01

    A multidisciplinary approach has been adopted to investigate and identify the source of malodour in washing machines and the potential for cross-contamination of laundry. Four washing machines were olfactively graded, and the number of colony-forming units (CFUs) bacteria was determined in four specific locations. Then, samples of terry-towel and fleece were washed, without the use of detergent, in the machines, and the occurrence of malodour over a 52-h period was assessed. Analysis of the scrapings from the four locations in the two malodorous machines identified a plethora of volatile organic compounds (VOCs) by either olfactory detection or mass spectral identification post-gas chromatographic separation. In addition, microbiological analysis from the swabs from the four locations within all four washing machines was carried out. Quantitative analysis of VOCs from 66 microbiological isolates from either the washing machines or fabrics was carried out. In total, 10 VOCs were identified: dimethyl disulfide, 3-methyl-1-butanol, 2,4-dithiapentane, dimethyl trisulfide, 2-tridecanone, indole, 2-phenylethanol, isovaleric acid, isobutyric acid and 1-undecene.

  17. Combining sieving and washing, a way to treat MSWI boiler fly ash.

    PubMed

    De Boom, Aurore; Degrez, Marc

    2015-05-01

    Municipal Solid Waste Incineration (MSWI) fly ashes contain some compounds that could be extracted and valorised. A process based on wet sieving and washing steps has been developed aiming to reach this objective. Such unique combination in MSWI fly ash treatment led to a non-hazardous fraction from incineration fly ashes. More specifically, MSWI Boiler Fly Ash (BFA) was separately sampled and treated. The BFA finer particles (13wt%) were found to be more contaminated in Pb and Zn than the coarser fractions. After three washing steps, the coarser fractions presented leaching concentrations acceptable to landfill for non-hazardous materials so that an eventual subsequent valorisation may be foreseen. At the contrary, too much Pb leached from the finest particles and this fraction should be further treated. Wet sieving and washing permit thus to reduce the leachability of MSWI BFA and to concentrate the Pb and Zn contamination in a small (in particle size and volume) fraction. Such combination would therefore constitute a straightforward and efficient basis to valorise coarse particles from MSWI fly ashes. PMID:25736808

  18. Combining sieving and washing, a way to treat MSWI boiler fly ash.

    PubMed

    De Boom, Aurore; Degrez, Marc

    2015-05-01

    Municipal Solid Waste Incineration (MSWI) fly ashes contain some compounds that could be extracted and valorised. A process based on wet sieving and washing steps has been developed aiming to reach this objective. Such unique combination in MSWI fly ash treatment led to a non-hazardous fraction from incineration fly ashes. More specifically, MSWI Boiler Fly Ash (BFA) was separately sampled and treated. The BFA finer particles (13wt%) were found to be more contaminated in Pb and Zn than the coarser fractions. After three washing steps, the coarser fractions presented leaching concentrations acceptable to landfill for non-hazardous materials so that an eventual subsequent valorisation may be foreseen. At the contrary, too much Pb leached from the finest particles and this fraction should be further treated. Wet sieving and washing permit thus to reduce the leachability of MSWI BFA and to concentrate the Pb and Zn contamination in a small (in particle size and volume) fraction. Such combination would therefore constitute a straightforward and efficient basis to valorise coarse particles from MSWI fly ashes.

  19. 100 Area soil washing: Bench scale tests on 116-F-4 pluto crib soil

    SciTech Connect

    Field, J.G.

    1994-06-10

    The Pacific Northwest Laboratory conducted a bench-scale treatability study on a pluto crib soil sample from 100 Area of the Hanford Site. The objective of this study was to evaluate the use of physical separation (wet sieving), treatment processes (attrition scrubbing, and autogenous surface grinding), and chemical extraction methods as a means of separating radioactively-contaminated soil fractions from uncontaminated soil fractions. The soil washing treatability study was conducted on a soil sample from the 116-F-4 Pluto Crib that had been dug up as part of an excavation treatability study. Trace element analyses of this soil showed no elevated concentrations above typically uncontaminated soil background levels. Data on the distribution of radionuclide in various size fractions indicated that the soil-washing tests should be focused on the gravel and sand fractions of the 116-F-4 soil. The radionuclide data also showed that {sup 137}Cs was the only contaminant in this soil that exceeded the test performance goal (TPG). Therefore, the effectiveness of subsequent soil-washing tests for 116-F-4 soil was evaluated on the basis of activity attenuation of {sup 137}Cs in the gravel- and sand-size fractions.

  20. Comparison of quality and freezability of water buffalo semen after washing or Sephadex filtration.

    PubMed

    Goyal, R L; Tuli, R K; Georgie, G C; Chand, D

    1996-09-01

    Split aliquots of pooled buffalo semen samples were processed before freezing 1) by washing twice with Tris-citric acid buffer by centrifugation and re-suspension to the original volume in the same buffer, or 2) or by passage through a G-15 Sephadex column. The effect of these procedures on progressive motility, percentages of live spermatozoa, sperm abnormalities and intact acrosomes and release of glutamate oxatoacetate transaminase (GOT) into the medium were assessed after extension, after equilibration and after 18 to 24 h or 15 d of frozen storage. Prior to extension, gel filtration reduced sperm concentration and enhanced progressive motility, whereas washing produced little effect on these attributes. Except in the case of GOT release, which was significantly (P < 0.05) lower after the washing of semen (34.3 +/- 16.40) than the filtering of semen (45.7 +/- 12.35), the 2 procedures did not cause significant effects (P > 0.05). Damage to spermatozoa due to freeze-processing was also similar in the 2 treatments, and the extent of beneficial effect in improved motility and live spermatozoan numbers after thawing was also similar.

  1. Effects of water washing on removing organic residues in bottom ashes of municipal solid waste incinerators.

    PubMed

    Lin, Yen-Ching; Panchangam, Sri Chandana; Wu, Chung-Hsin; Hong, Pui-Kwan Andy; Lin, Cheng-Fang

    2011-01-01

    Due to their potential toxicity and odourous nature, the residual organics in municipal solid waste incinerators are recently gaining attention as an important issue of resources recovery apart from their complex mixture of organic counterpart. Studies of the organic fractions in municipal solid waste incinerator residues have been limited. In this study, extended solid-phase extraction of the water-washed bottom ash and liquid-phase extraction of the washing water were carried out with regard to bottom ash samples from three mass-burning incinerators in Taipei County (Taiwan) during four consecutive seasons of year 2008-2009. Supercritical fluid extraction and Soxtec extraction techniques along with GC-MS were successfully used to characterize the residual organics in weathered and washed bottom ashes. Supercritical fluid extraction provided the quantification of aliphatics and aromatic compounds such as hexanoic acid and benzaldehyde, respectively. Soxtec extraction was useful for qualitative analysis of aromatic and aliphatic groups in the ashes and many of which were odourous and toxic compounds. By mixing one unit weight (g) bottom ash with two unit volume (mL) water for 15 min, total organic carbon in the bottom ash was greatly reduced (e.g., from 4.1 to 1.8 wt.%). Among the removed were foul odour-causing compounds such as pyridine and quinoline derivatives, while some aromatic compounds such as 4-hydroxybenzaldehyde and low-molecular-weight aliphatics such as hexanoic acid remained. The results here suggest that washing with water can be an effective pre-treatment step for removing odour-causing and environmental concerned organics. PMID:21112610

  2. Minimum Additive Waste Stabilization (MAWS), Phase I: Soil washing final report

    SciTech Connect

    1995-08-01

    As a result of the U.S. Department of Energy`s environmental restoration and technology development activities, GTS Duratek, Inc., and its subcontractors have demonstrated an integrated thermal waste treatment system at Fernald, OH, as part the Minimum Additive Waste Stabilization (MAWS) Program. Specifically, MAWS integrates soil washing, vitrification of mixed waste streams, and ion exchange to recycle and remediate process water to achieve, through a synergistic effect, a reduction in waste volume, increased waste loading, and production of a durable, leach-resistant, stable waste form suitable for disposal. This report summarizes the results of the demonstration/testing of the soil washing component of the MAWS system installed at Fernald (Plant 9). The soil washing system was designed to (1) process contaminated soil at a rate of 0.25 cubic yards per hour; (2) reduce overall waste volume and provide consistent-quality silica sand and contaminant concentrates as raw material for vitrification; and (3) release clean soil with uranium levels below 35 pCi/g. Volume reductions expected ranged from 50-80 percent; the actual volume reduction achieved during the demonstration reached 66.5 percent. The activity level of clean soil was reduced to as low as 6 pCi/g from an initial average soil activity level of 17.6 pCi/g (the highest initial level of soil provided for testing was 41 pCi/g). Although the throughput of the soil washing system was inconsistent throughout the testing period, the system was online for sufficient periods to conclude that a rate equivalent to 0.25 cubic yards per hour was achieved.

  3. Monitoring receptor trafficking following retromer and WASH deregulation.

    PubMed

    Osborne, Douglas G; Phillips-Krawczak, Christine A; Billadeau, Daniel D

    2015-01-01

    Cell surface receptors that have been internalized and enter the endocytic pathway have multiple fates including entrance into the multivesicular body pathway on their way to lysosomal degradation, recycling back to the cell surface, or retrograde trafficking out of the endolysosomal system back to the Golgi apparatus. Two ubiquitously expressed protein complexes, WASH and the endosomal coat complex retromer, function together to play a central role in directing the fate of receptors into the latter two pathways. In this chapter, we describe fluorescent- and flow cytometry-based methods for analyzing the recycling and retrograde trafficking of two receptors, α5β1 and CI-M6PR, whose intracellular fates are regulated by WASH and retromer activity. The guidelines presented in this chapter can be applied to the analysis of any cell surface or intracellular membrane protein to determine the impact of WASH or retromer deregulation on its intracellular trafficking route. PMID:26360036

  4. Wash-out in N2-dominated leptogenesis

    NASA Astrophysics Data System (ADS)

    Hahn-Woernle, F.

    2010-08-01

    We study the wash-out of a cosmological baryon asymmetry produced via leptogenesis by subsequent interactions. Therefore we focus on a scenario in which a lepton asymmetry is established in the out-of-equilibrium decays of the next-to-lightest right-handed neutrino. We apply the full classical Boltzmann equations without the assumption of kinetic equilibrium and including all quantum statistical factors to calculate the wash-out of the lepton asymmetry by interactions of the lightest right-handed state. We include scattering processes with top quarks in our analysis. This is of particular interest since the wash-out is enhanced by scatterings and the use of mode equations with quantum statistical distribution functions. In this way we provide a restriction on the parameter space for this scenario.

  5. Washing and caustic leaching of Hanford Tank C-106 sludge

    SciTech Connect

    Lumetta, G.J.; Wagner, M.J.; Hoopes, F.V.; Steele, R.T.

    1996-10-01

    This report describes the results of a laboratory-scale washing and caustic leaching test performed on sludge from Hanford Tank C-106. The purpose of this test was to determine the behavior of important sludge components when subjected to washing with dilute or concentrated sodium hydroxide solutions. The results of this laboratory-scale test were used to support the design of a bench-scale washing and leaching process used to prepare several hundred grams of high-level waste solids for vitrification tests to be done by private contractors. The laboratory-scale test was conducted at Pacific Northwest Laboratory in FY 1996 as part of the Hanford privatization effort. The work was funded by the US Department of Energy through the Tank Waste Remediation System (TWRS; EM-30).

  6. Gravity and magnetic study of Yucca Wash, southwest Nevada

    SciTech Connect

    Langenheim, V.E.; Ponce, D.A.; Oliver, H.W.; Sikora, R.F.

    1993-12-31

    Gravity and ground magnetic data were collected along five traverses across and one traverse along Yucca Wash in the southwest quadrant of the Nevada Test Site. Two additional ground magnetic profiles were collected approximately 100 m to either side of the longitudinal profile. These data do not indicate major vertical offsets greater than 100 m using a density contrast of 0.2 to 0.3 g/cm{sup 3} along the proposed Yucca Wash fault. A broad magnetic high coincides with the location of the hydrologic gradient. Density profiling, a technique used to determine the average density of small topographic features, suggests that the density of near-surface material in the vicinity of Yucca Wash is about 2.0 g/cm{sup 3}.

  7. Increasing hand washing compliance with a simple visual cue.

    PubMed

    Ford, Eric W; Boyer, Brian T; Menachemi, Nir; Huerta, Timothy R

    2014-10-01

    We tested the efficacy of a simple, visual cue to increase hand washing with soap and water. Automated towel dispensers in 8 public bathrooms were set to present a towel either with or without activation by users. We set the 2 modes to operate alternately for 10 weeks. Wireless sensors were used to record entry into bathrooms. Towel and soap consumption rates were checked weekly. There were 97,351 hand-washing opportunities across all restrooms. Towel use was 22.6% higher (P=.05) and soap use was 13.3% higher (P=.003) when the dispenser presented the towel without user activation than when activation was required. Results showed that a visual cue can increase hand-washing compliance in public facilities. PMID:24228670

  8. Improving protein array performance: focus on washing and storage conditions.

    PubMed

    Nath, Nidhi; Hurst, Robin; Hook, Brad; Meisenheimer, Poncho; Zhao, Kate Q; Nassif, Nadine; Bulleit, Robert F; Storts, Douglas R

    2008-10-01

    For protein microarrays, maintaining protein stability during the slide processing steps of washing, drying, and storage is of major concern. Although several studies have focused on the stability of immobilized antibodies in antibody microarrays, studies on protein-protein interaction arrays and enzyme arrays are lacking. In this paper we used five bait-prey protein interaction pairs and three enzymes to optimize the washing, drying, and storage conditions for protein arrays. The protein arrays for the study were fabricated by combining HaloTag technology and cell-free protein expression. The HaloTag technology, in combination with cell-free expression, allowed rapid expression and immobilization of fusion proteins on hydrogel-coated glass slides directly from cell extracts without any prior purification. Experimental results indicate enzyme captured on glass slides undergoes significant loss of activity when washed and spin-dried using only phosphate buffer, as is typically done with antibody arrays. The impact of washing and spin-drying in phosphate buffer on protein-protein interaction arrays was minimal. However, addition of 5% glycerol to the wash buffer helps retain enzyme activity during washing and drying. We observed significant loss of enzyme activity when slides were stored dry at 4 degrees C, however immobilized enzymes remained active for 30 days when stored at -20 degrees C in 50% glycerol. We also found that cell-free extract containing HaloTag-fused enzymes could undergo multiple freeze/thaw cycles without any adverse impact on enzyme activity. The findings indicate that for large ongoing studies, proteins of interest expressed in cell-free extract can be stored at -70 degrees C and repeatedly used to print small batches of protein array slides to be used over a few weeks.

  9. 100 Area soil washing bench-scale test procedures

    SciTech Connect

    Freeman, H.D.; Gerber, M.A.; Mattigod, S.V.; Serne, R.J.

    1993-03-01

    This document describes methodologies and procedures for conducting soil washing treatability tests in accordance with the 100 Area Soil Washing Treatability Test Plan (DOE-RL 1992, Draft A). The objective of this treatability study is to evaluate the use of physical separation systems and chemical extraction methods as a means of separating chemically and radioactively contaminated soil fractions from uncontaminated soil fractions. These data will be primarily used for determining feasibility of the individual unit operations and defining the requirements for a system, or systems, for pilot-scale testing.

  10. Washing the patient: dignity and aesthetic values in nursing care.

    PubMed

    Pols, Jeannette

    2013-07-01

    Dignity is a fundamental concept, but its meaning is not clear. This paper attempts to clarify the term by analysing and reconnecting two meanings of dignity: humanitas and dignitas. Humanitas refers to citizen values that protect individuals as equal to one another. Dignitas refers to aesthetic values embedded in genres of sociality that relate to differences between people. The paper explores these values by way of an empirical ethical analysis of practices of washing psychiatric patients in nursing care. Nurses legitimate the washing of reluctant patients with reference to dignity. The analysis shows the intertwinement of humanitas and dignitas that gives dignity its fundamental meaning.

  11. Investigation of Rheological Impacts on Sludge Batch 3 as Insoluble Solids and Wash Endpoints are Adjusted

    SciTech Connect

    Fellinger, T. L.

    2005-07-12

    The Defense Waste Processing Facility (DWPF) is currently processing and immobilizing radioactive sludge slurry into a durable borosilicate glass. The DWPF has already processed three sludge batches (Sludge Batch 1A, Sludge Batch 1B, and Sludge Batch 2) and is currently processing the fourth sludge batch (Sludge Batch 3). A sludge batch is defined as a single tank of sludge slurry or a combination of sludge slurries from different tanks that has been or will be qualified before being transferred to DWPF. As a part of the Sludge Batch 3 (SB3) qualification task, rheology measurements of the sludge slurry were requested at different insoluble solids loadings. These measurements were requested in order to gain insight into potential processing problems that may occur as the insoluble solids are adjusted up or down (by concentration or dilution) during the process. As a part of this study, a portion of the ''as received'' SB3 sample was washed with inhibited water (0.015 M NaOH and 0.015 M NaNO2) to target 0.5M Na versus a measured 1M Na in the supernate. The purpose of the ''washing'' step was to allow a comparison of the SB3 rheological data to the rheological data collected for Sludge Batch 2 (SB2) and to determine if there was a dependence of the yield stress and consistency as a function of washing. The ''as received'' SB3 rheology data was also compared to SB3 simulants prepared by the Simulant Development Program in order to provide guidance for selecting a simulant that is more representative of the rheological properties of the radioactive sludge slurry. A summary of the observations, conclusions are: (1) The yield stress and plastic viscosity increased as the weight percent insoluble solids were increased for the ''as received'' and ''washed'' SB3 samples, at a fixed pH. (2) For the same insoluble solids loading, the yield stress for the SB2 sample is approximately a factor of three higher than the ''as received'' SB3 sample. There also appears to be small

  12. Phase I characterization of the HEPA (High Efficiency Particulate Air) filter media used in the airborne activity confinement system at the Savannah River Site

    SciTech Connect

    Novick, V.J.; Higgins, P.J. )

    1989-01-01

    The purpose of this report was to characterize the HEPA filter media material. This work consisted of two major tasks. First, the pressure drop characteristics of the HEPA filter material were measured as a function of the aerosol mass loading. Particle size effects were studied by using three different particle size distributions to load the filter material. The second task was to determine the filtration efficiency spectrum for solid particles as a function of particle diameter. The filtration efficiency was measured at two different media velocities, one corresponding to the equivalent flow rate under normal operating conditions, the other corresponding to the minimum equivalent flow rate expected through the filter compartments. These tests were conducted at the Argonne National Laboratory between September 1988 and February 1989. 20 refs., 31 figs., 10 tabs.

  13. Recovery of plutonium from HEPA filters by Ce(IV)-promoted dissolution of PuO/sub 2/ and recycle of the cerium promoter

    SciTech Connect

    Leuze, R. E.; Bond, W. D.; Scheitlin, F. M.

    1980-01-01

    The experimental studies carried out included (1) the electrolytic production of Ce(IV) from Ce(III), (2) the leaching of refractory PuO/sub 2/ from HEPA filter materials with maintenance of Ce(IV) concentrations by anodic oxidation during leaching, and (3) evaluation of methods for contacting the HEPA solids with the leaching solution and for separating the solid residue from the leaching liquor. Anodic oxidation of Ce(III) was accomplished with an electric current efficiency of about 85% at current densities of 0.04 to 0.4 A/dm/sup 2/ at a platinum anode. Refractory PuO/sub 2/ was dissolved by a 4.0 M HNO/sub 3/ - 0.1 M Ce(IV) solution in 1.5 h at 100/sup 0/C using stirred-contact leaching of the solids or by recirculating the leachant through a packed column of the solids. Cerium (IV) concentrations were maintained continuously by anodic oxidation throughout leaching. Dissolution times up to 10 h were required unless the HEPA media were oxidized initially in air at 300/sup 0/C to destroy carbonaceous species which consumed Ce(IV) more rapidly than it could be regenerated by anodic oxidation. Leaching solids in packed columns avoided the relatively difficult liquid-solids separation by centrifugation which was required after stirred-contact leaching; however, the solids handling difficulties associated with charging and discharging of the packed columns in a remote environment remain a significant design obstacle. A chemical flowsheet is proposed for the recovery of actinides from HEPA filters. A 4 M HNO/sub 3/ - 0.1 M Ce(IV) nitrate solution is used as the leachant and the Ce(III) is recycled to the leaching operation using bidentate solvent extraction.

  14. Fire tests to evaluate the potential fire threat and its effects on HEPA filter integrity in cell ventilation at the Oak Ridge National Laboratory, Building 7920

    SciTech Connect

    Hasegawa, H.K.; Staggs, K.J.; Doughty, S.M.

    1992-12-01

    As a result of a DOE (Tiger Team) Technical Safety Appraisal (November 1990) of the Radiochemical Engineering Development Center (REDC), ORNL Building 7920, a number of fire protection concerns were identified. The primary concern was the perceived loss of ventilation system containment due to the thermal destruction and/or breaching of the prefilters and/or high-efficiency particulate air filters (HEPA `s) and the resultant radioactive release to the external environment. The following report describes the results of an extensive fire test program performed by the Fire Research Discipline (FRD) of the Special Projects Division of Lawrence Livermore National Lab (LLNL) and funded by ORNL to address these concerns. Full scale mock-ups of a REDC hot cell tank pit, adjacent cubicle pit, and associated ventilation system were constructed at LLNL and 13 fire experiments were conducted to specifically answer the questions raised by the Tiger Team. Our primary test plan was to characterize the burning of a catastrophic solvent spill (kerosene) of 40 liters and its effect on the containment ventilation system prefilters and HEPA filters. In conjunction with ORNL and Lockwood Greene we developed a test matrix that assessed the fire performance of the prefilters and HEPA filters; evaluated the fire response of the fiber reinforced plastic (FRP) epoxy ventilation duct work; the response and effectiveness of the fire protection system, the effect of fire in a cubicle on the vessel off-gas (VOG) elbow, and other fire safety questions.

  15. Formation of GSH-trapped reactive metabolites in human liver microsomes, S9 fraction, HepaRG-cells, and human hepatocytes.

    PubMed

    Lassila, Toni; Rousu, Timo; Mattila, Sampo; Chesné, Christophe; Pelkonen, Olavi; Turpeinen, Miia; Tolonen, Ari

    2015-11-10

    The objective was to compare several in vitro human liver-derived subcellular and cellular incubation systems for the formation of GSH-trapped reactive metabolites. Incubations of pooled human liver microsomes, human liver S9 fractions, HepaRG-cells, and human hepatocytes were performed with glutathione as a trapping agent. Experiments with liver S9 were performed under two conditions, using only NADPH and using a full set of cofactors enabling also conjugative metabolism. Ten structurally different compounds were used as a test set, chosen as either "positive" (ciprofloxacin, clozapine, diclofenac, ethinyl estradiol, pulegone, and ticlopidine) or "negative" (caffeine, citalopram, losartan, montelukast) compounds, based on their known adverse reactions on liver or bone marrow. GSH conjugates were observed for seven of the ten compounds; while no conjugates were observed for caffeine, citalopram, or ciprofloxacin. Hepatocyte and HepaRG assays produced a clearly lower number and lower relative abundance of GSH conjugates compared to assays with microsomes and S9 fractions. The major GSH conjugates were different for many compounds in cellular subfractions and cell-based systems. Hepatocytes generally produced a higher number of GSH conjugates than HepaRG cells, although the differences were minor. The results show that the hepatic enzyme system used for screening of GSH-trapped reactive metabolites do have a high impact on the results, and results between different systems are comparable only qualitatively. PMID:26263063

  16. Detection of main metabolites of XLR-11 and its thermal degradation product in human hepatoma HepaRG cells and human urine.

    PubMed

    Kanamori, Tatsuyuki; Kanda, Koji; Yamamuro, Tadashi; Kuwayama, Kenji; Tsujikawa, Kenji; Iwata, Yuko Togawa; Inoue, Hiroyuki

    2015-04-01

    The metabolism of (1-(5-fluoropentyl)-1H-indol-3-yl)(2,2,3,3-tetramethylcyclopropyl)methanone (XLR-11), a novel synthetic cannabinoid, was studied using a HepaRG cell culture. The HepaRG cells were incubated with the drug for 48 hours and the metabolites were extracted from the culture medium by liquid-liquid extraction. The extract was analyzed by liquid chromatography/mass spectrometry to detect the metabolites. N-(5-Hydroxypentyl) metabolite and N-pentanoic acid metabolite were identified in the culture medium of XLR-11, and several other metabolites, presumably formed by oxidation of the first two metabolites and XLR-11, were detected. The extract of an XLR-11 user's urine was also analyzed; however, the metabolites detected in the urine were different from XLR-11 metabolites in the medium. A metabolic experiment with the thermal degradation product of XLR-11, XLR-11 degradant, using HepaRG cells revealed that the urinary metabolites were almost identical to the XLR-11 degradant metabolites. These findings suggest that most of the XLR-11 was degraded by heating when the user smoked the herbal product containing XLR-11.

  17. Effect of different curd-washing methods on the insoluble Ca content and rheological properties of Colby cheese during ripening.

    PubMed

    Lee, M-R; Johnson, M E; Govindasamy-Lucey, S; Jaeggi, J J; Lucey, J A

    2011-06-01

    A curd-washing step is used in the manufacture of Colby cheese to decrease the residual lactose content and, thereby, decrease the potential formation of excessive levels of lactic acid. The objective of this study was to investigate the effect of different washing methods on the Ca equilibrium and rheological properties of Colby cheese. Four different methods of curd-washing were performed. One method was batch washing (BW), where cold water (10°C) was added to the vat, with and without stirring, where curds were in contact with cold water for 5 min. The other method used was continuous washing (CW), with or without stirring, where curds were rinsed with continuously running cold water for approximately 7 min and water was allowed to drain immediately. Both methods used a similar volume of water. The manufacturing pH values were similar in all 4 treatments. The insoluble (INSOL) Ca content of cheese was measured by juice and acid-base titration methods and the rheological properties were measured by small amplitude oscillatory rheology. The levels of lactose in cheese at 1 d were significantly higher in CW cheese (0.06-0.11%) than in BW cheeses (∼0.02%). The levels of lactic acid at 2 and 12 wk were significantly higher in CW cheese than in BW cheeses. No differences in the total Ca content of cheeses were found. Cheese pH increased during ripening from approximately 5.1 to approximately 5.4. A decrease in INSOL Ca content of all cheeses during ripening occurred, although a steady increase in pH took place. The initial INSOL Ca content as a percent of total Ca in cheese ranged from 75 to 78% in all cheeses. The INSOL Ca content of cheese was significantly affected by washing method. Stirring during manufacturing did not have a significant effect on the INSOL Ca content of cheese during ripening. Batch-washed cheeses had significantly higher INSOL Ca contents than did CW cheeses during the first 4 wk of ripening. The maximum loss tangent values (meltability

  18. Understanding wash efficiency and chloride transfer in copper solvent extraction

    NASA Astrophysics Data System (ADS)

    Burkhardt, D. J.

    2003-07-01

    Carryover of entrained aqueous from primary leaching operations into copper electrowinning electrolytes introduces impurities that can affect cathode quality and cause corrosion. As a result, more operations are introducing wash stages in their solvent extraction circuits in an attempt to dilute these entrainments with high-quality water.

  19. DEMONSTRATION BULLETIN: SOIL/SEDIMENT WASHING SYSTEM BERGMANN USA

    EPA Science Inventory

    The Bergmann USA Soil/Sediment Washing System is a waste minimization technique designed to separate or "partition" soils and sediments by grain size and density. In this water-based volume reduction process, hazardous contaminants are concentrated into a small residual portion...

  20. Cadmium Removal from Rice by Separating and Washing Protein Isolate.

    PubMed

    Huo, Yinqiang; Du, Hongying; Xue, Bingying; Niu, Meng; Zhao, Siming

    2016-06-01

    In this study detoxification of 3 Chinese Cd-contaminated cultivars (Jinyou463, Yuchi, and Xiangzaoxian 32) of rice was explored. By separation with an alkaline method, Cd concentrations of the starch isolates were decreased from 0.2769, 0.4037, and 0.5156 mg/kg in starting milled rice to 0.1056, 0.1585, and 0.1923 mg/kg, respectively. However, the Cd concentrations reached up to 2.5905, 3.1628, and 4.8593 mg/kg in the protein isolates, respectively. Therefore, 10 common acids in food industry were investigated to remove Cd from protein isolate by washing process. The optimal washing conditions were 0.5 M citric acid, acid to rice protein isolate ratio of 6:1 v/w, shaking time of 1 h at room temperature. The rice protein isolate showed a significant decrease in Cd concentration and the removal efficiency was more than 95% after 2 washings at optimized conditions. Rice proteins were not degraded at all and had very little loss during citric acid washing process. The study presents a promising way of depurating Cd-contaminated rice, and meanwhile it reduces the risk of heavy metal causing food safety issues effectively. PMID:27159878

  1. 14. VARIOUS OUTBUILDINGS: a) OCTAGONAL STRUCTURE (center): WASH HOUSE b) ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    14. VARIOUS OUTBUILDINGS: a) OCTAGONAL STRUCTURE (center): WASH HOUSE b) SQUARE BUILDING WITH HIPPED ROOF (right front): SMOKEHOUSE c) BRICK BUILDING WITH END CHIMNEYS (left front): KITCHEN AND COOK'S BUILDING d) LONG BRICK BUILDING (in background): SERVANTS' QUARTERS (?) - Colonel McNeal House, Union & Bills Streets, Bolivar, Hardeman County, TN

  2. Conservation of water for washing beef heads at harvest.

    PubMed

    DeOtte, R E; Spivey, K S; Galloway, H O; Lawrence, T E

    2010-03-01

    The objective of this research was to develop methods to conserve water necessary to cleanse beef heads prior to USDA-FSIS inspection. This was to be accomplished by establishing a baseline for the minimum amount of water necessary to adequately wash a head and application of image analysis to provide an objective measure of head cleaning. Twenty-one beef heads were manually washed during the harvest process. An average 18.75 L (2.49 SD) and a maximum of 23.88 L were required to cleanse the heads to USDA-FSIS standards. Digital images were captured before and after manual washing then evaluated for percentage red saturation using commercially available image analysis software. A decaying exponential curve extracted from these data indicated that as wash water increased beyond 20 L the impact on red saturation decreased. At 4 sigma from the mean of 18.75 L, red saturation is 16.0 percent, at which logistic regression analysis indicates 99.994 percent of heads would be accepted for inspection, or less than 1 head in 15,000 would be rejected. Reducing to 3 sigma would increase red saturation to 27.6 percent, for which 99.730 percent of heads likely would be accepted (less than 1 in 370 would be rejected). PMID:20374798

  3. Radioactive demonstration of the ``late wash`` Precipitate Hydrolysis Process

    SciTech Connect

    Bibler, N.E.; Ferrara, D.M.; Ha, B.C.

    1992-06-30

    This report presents results of the radioactive demonstration of the DWPF Precipitate Hydrolysis Process as it would occur in the ``late wash`` flowsheet in the absence of hydroxylamine nitrate. Radioactive precipitate containing Cs-137 from the April, 1983, in-tank precipitation demonstration in Tank 48 was used for these tests.

  4. Radioactive demonstration of the late wash'' Precipitate Hydrolysis Process

    SciTech Connect

    Bibler, N.E.; Ferrara, D.M.; Ha, B.C.

    1992-06-30

    This report presents results of the radioactive demonstration of the DWPF Precipitate Hydrolysis Process as it would occur in the late wash'' flowsheet in the absence of hydroxylamine nitrate. Radioactive precipitate containing Cs-137 from the April, 1983, in-tank precipitation demonstration in Tank 48 was used for these tests.

  5. Ink and Wash Painting for Children with Visual Impairment

    ERIC Educational Resources Information Center

    Shih, Chih-Ming; Chao, Hsin-Yi

    2010-01-01

    Five children with visual impairments received instruction in drawing, using ink and wash painting and calligraphy techniques. A special system developed by a blind Taiwanese Chinese calligrapher, Tsann-Cherng Liaw, was used to help the children orient and refine their work. Children's performance on simple drawing tasks was compared before and…

  6. 18. Photocopy of circa 1839 ink and wash drawing by ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    18. Photocopy of circa 1839 ink and wash drawing by Richard Upjohn in Avery Library, Columbia University ELEVATION OF ENTRANCE FRONT (above) AND PRELIMINARY OR PARTIAL FIRST FLOOR PLAN WITH TWO SMALL ELEVATION SKETCHES (below) - Kingscote, Bellevue Avenue & Bowery Street, Newport, Newport County, RI

  7. Conservation of water for washing beef heads at harvest.

    PubMed

    DeOtte, R E; Spivey, K S; Galloway, H O; Lawrence, T E

    2010-03-01

    The objective of this research was to develop methods to conserve water necessary to cleanse beef heads prior to USDA-FSIS inspection. This was to be accomplished by establishing a baseline for the minimum amount of water necessary to adequately wash a head and application of image analysis to provide an objective measure of head cleaning. Twenty-one beef heads were manually washed during the harvest process. An average 18.75 L (2.49 SD) and a maximum of 23.88 L were required to cleanse the heads to USDA-FSIS standards. Digital images were captured before and after manual washing then evaluated for percentage red saturation using commercially available image analysis software. A decaying exponential curve extracted from these data indicated that as wash water increased beyond 20 L the impact on red saturation decreased. At 4 sigma from the mean of 18.75 L, red saturation is 16.0 percent, at which logistic regression analysis indicates 99.994 percent of heads would be accepted for inspection, or less than 1 head in 15,000 would be rejected. Reducing to 3 sigma would increase red saturation to 27.6 percent, for which 99.730 percent of heads likely would be accepted (less than 1 in 370 would be rejected).

  8. 30 CFR 206.458 - Determination of washing allowances.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... life of the reserves which the wash plant services, whichever is appropriate, or a unit of production... breached its duty to the lessor to market the production for the mutual benefit of the lessee and the... based on a dollar-per-unit basis, the lessee shall convert whatever consideration is paid to a...

  9. 35. Photocopy of detail of ink and wash rendering by ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    35. Photocopy of detail of ink and wash rendering by N. G. Starkwether in collection of Mr. & Mrs. Richard T. Pratt, Camden ELEVATIONS OF ITALIAN VILLA FOR WILLIAM C. PRATT - CAMDEN PLACE - RIVER FRONT - Camden, Rappahannock River, Port Royal, Caroline County, VA

  10. 36. Photocopy of detail of ink and wash rendering by ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    36. Photocopy of detail of ink and wash rendering by N. G. Starkwether in collection of Mr. & Mrs. Richard T. Pratt, Camden ELEVATIONS OF ITALIAN VILLA FOR WILLIAM C. PRATT - CAMDEN PLACE - DRIVE FRONT - Camden, Rappahannock River, Port Royal, Caroline County, VA

  11. Ultrasonic system for continuous washing of textiles in liquid layers.

    PubMed

    Gallego-Juarez, Juan A; Riera, Enrique; Acosta, Victor; Rodríguez, Germán; Blanco, Alfonso

    2010-01-01

    The use of ultrasonic energy for washing of textiles has been tried several times without achieving practical development. In fact, the softness of the fibres makes the cavitation to produce small erosion effect and the reticulate structure of the fabric favours the formation of air bubble layers which obstruct wave penetration. In addition, a high proportion of water with respect to the wash load and a certain water degassing is required to assure efficiency and homogeneity in the wash performance. Such requirements have hindered the commercial development of the ultrasonic washing machines for domestic purposes. For specific industrial applications, a great part of these limitations may be overcome. This article deals with a new process in which the fabric is exposed to the ultrasonic field in a flat format. Such process has been implemented at laboratory and at semi-industrial stage by using specially designed power ultrasonic transducers with rectangular plate radiators. The cleaning effect is produced by the intense cavitation field generated by the plate radiator within a thin layer of liquid where the fabric is introduced. The homogeneity of such effect is achieved by the successive exposure of all the fabric areas to the intense acoustic field. In this paper the structure and performance of the developed system are shown.

  12. 1. GENERAL VIEW FROM BONY PILE LOOKING SOUTH. WASH HOUSE ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    1. GENERAL VIEW FROM BONY PILE LOOKING SOUTH. WASH HOUSE IN LEFT BACKGROUND. TIPPLE AND CLEANING PLANT TO RIGHT. IN CENTER IS A TANK USED FOR TREATING MINE REFUSE AND ACID RUNOFF. - Eureka No. 40, Tipple & Cleaning Plant, East of State Route 56, north of Little Paint Creek, Scalp Level, Cambria County, PA

  13. 62. May 1985. NORTH END OF WASH HOUSE (Negative slightly ...

    Library of Congress Historic Buildings Survey, Historic Engineering Record, Historic Landscapes Survey

    62. May 1985. NORTH END OF WASH HOUSE (Negative slightly reticulated. Tree behind fence is common fig, Ficus carica.) - Borough House, West Side State Route 261, about .1 mile south side of junction with old Garners Ferry Road, Stateburg, Sumter County, SC

  14. 21 CFR 211.52 - Washing and toilet facilities.

    Code of Federal Regulations, 2013 CFR

    2013-04-01

    ... 21 Food and Drugs 4 2013-04-01 2013-04-01 false Washing and toilet facilities. 211.52 Section 211.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and...

  15. 21 CFR 211.52 - Washing and toilet facilities.

    Code of Federal Regulations, 2012 CFR

    2012-04-01

    ... 21 Food and Drugs 4 2012-04-01 2012-04-01 false Washing and toilet facilities. 211.52 Section 211.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and...

  16. 21 CFR 211.52 - Washing and toilet facilities.

    Code of Federal Regulations, 2014 CFR

    2014-04-01

    ... 21 Food and Drugs 4 2014-04-01 2014-04-01 false Washing and toilet facilities. 211.52 Section 211.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and...

  17. 21 CFR 211.52 - Washing and toilet facilities.

    Code of Federal Regulations, 2010 CFR

    2010-04-01

    ... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Washing and toilet facilities. 211.52 Section 211.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and...

  18. 21 CFR 211.52 - Washing and toilet facilities.

    Code of Federal Regulations, 2011 CFR

    2011-04-01

    ... 21 Food and Drugs 4 2011-04-01 2011-04-01 false Washing and toilet facilities. 211.52 Section 211.52 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Buildings and...

  19. Combined soil washing and CDEO for the removal of atrazine from soils.

    PubMed

    dos Santos, Elisama Vieira; Sáez, Cristina; Martínez-Huitle, Carlos Alberto; Cañizares, Pablo; Rodrigo, Manuel Andres

    2015-12-30

    In this work, it is studied the removal of atrazine from spiked soils by soil washing using surfactant fluids, followed by the treatment of the resulting washing waste by electrolysis with boron doped diamond (BDD) anode. Results confirm that combination of both technologies is efficient for the removal and total mineralization of atrazine. Ratio surfactant/soil is a key parameter for the removal of atrazine from soil and influences significantly in the characteristic of the wastewater produced, affecting not only to the total organic load but also to the mean size of micelles. The higher the ratio surfactant soil, the lower is the size of the particles. Electrolyses of this type of waste attain the complete mineralization. TOC and COD are removed from the start of the treatment but the key of the treatment is the reduction in size of the micelles, which lead to a higher negative charge in the surface and to the faster depletion of the surfactant as compared with the pesticide. PMID:26164070

  20. Combined soil washing and CDEO for the removal of atrazine from soils.

    PubMed

    dos Santos, Elisama Vieira; Sáez, Cristina; Martínez-Huitle, Carlos Alberto; Cañizares, Pablo; Rodrigo, Manuel Andres

    2015-12-30

    In this work, it is studied the removal of atrazine from spiked soils by soil washing using surfactant fluids, followed by the treatment of the resulting washing waste by electrolysis with boron doped diamond (BDD) anode. Results confirm that combination of both technologies is efficient for the removal and total mineralization of atrazine. Ratio surfactant/soil is a key parameter for the removal of atrazine from soil and influences significantly in the characteristic of the wastewater produced, affecting not only to the total organic load but also to the mean size of micelles. The higher the ratio surfactant soil, the lower is the size of the particles. Electrolyses of this type of waste attain the complete mineralization. TOC and COD are removed from the start of the treatment but the key of the treatment is the reduction in size of the micelles, which lead to a higher negative charge in the surface and to the faster depletion of the surfactant as compared with the pesticide.

  1. Hand Washing Among School Children in Bogotá, Colombia

    PubMed Central

    Lopez-Quintero, Catalina; Freeman, Paul

    2009-01-01

    Objectives. We assessed hand-washing behaviors and intentions among school children in Bogotá, Colombia, to help identify and overcome barriers to proper hygiene practices. Methods. Data on hand-washing behavior and intentions and individual and contextual factors were collected from 2042 sixth- through eighth-grade students in 25 schools in Bogotá via anonymous questionnaires. A member of the school administration or teaching staff completed a questionnaire about the school environment. Site inspections of bathroom facilities were conducted. Results. Only 33.6% of the sample reported always or very often washing hands with soap and clean water before eating and after using the toilet. About 7% of students reported regular access to soap and clean water at school. A high level of perceived control was the strongest predictor of positive hand-washing intentions (adjusted odds ratio [AOR] = 6.0; 95% confidence interval [CI] = 4.8, 7.5). Students with proper hand-washing behavior were less likely to report previous-month gastrointestinal symptoms (OR = 0.8; 95% CI = 0.6, 0.9) or previous-year school absenteeism (OR = 0.7; 95% CI = 0.6, 0.9). Conclusions. Scarcity of adequate facilities in most schools in Bogotá prevents children from adopting proper hygienic behavior and thwarts health promotion efforts. The current renovation program of public schools in Bogotá provides a unique opportunity to meet the challenges of providing a supportive environment for adoption of healthy behaviors. PMID:19008513

  2. A pilot plant scale evaluation of a new process aid for enhancing chlorine efficacy against pathogen survival and cross-contamination during produce wash.

    PubMed

    Luo, Yaguang; Nou, Xiangwu; Millner, Patricia; Zhou, Bin; Shen, Cangliang; Yang, Yang; Wu, Yunpeng; Wang, Qin; Feng, Hao; Shelton, Dan

    2012-08-17

    Developing food safety intervention technology that can be readily adopted by the industry often requires test conditions that match as closely as possible to those of commercial food processing operations; yet biosafety risks inherent in pathogen studies constrain most experiments to laboratory settings. In this study, we report the first semi-commercial pilot-scale evaluation of a new process aid, T128, for its impact on enhancing the antimicrobial efficacy of chlorinated wash water against pathogen survival and cross-contamination. A non-pathogenic, BSL-1, strain of Escherichia coli O157:H7 was inoculated onto freshly harvested baby spinach leaves and washed with large amounts of freshly cut un-inoculated iceberg lettuce shreds in wash water with free chlorine periodically replenished, in the presence or absence of T128. Changes in water quality and pathogen survival and cross-contamination were monitored at every 2 min intervals for up to 36 min for each treatment during the wash operation. Results indicated that the use of T128 did not significantly (P>0.05) influence the rate of wash water deterioration, nor the pathogen populations remaining on the inoculated spinach leaves. However, in the absence of T128 (control), survival of E. coli O157:H7 in wash water and cross-contamination of un-inoculated lettuce frequently occurred when free chlorine in solution dropped below 1mg/l during the wash process. In contrast, the use of T128 significantly reduced the occurrence of E. coli O157:H7 surviving in wash water and of cross-contamination to un-inoculated shredded iceberg lettuce under the same operational conditions, suggesting that the application of T128 in a chlorine-based fresh produce sanitization system could increase the safety margin of process control on fresh-cut operations.

  3. Effect of freezing, hot tumble drying and washing with eucalyptus oil on house dust mites in soft toys.

    PubMed

    Chang, Chin-Fu; Wu, Francis Fu-Sheng; Chen, Chi-Ying; Crane, Julian; Siebers, Rob

    2011-09-01

    Soft toys are a major source of house dust mites (HDM) and HDM allergens, and sleeping with soft toys is a significant risk factor for HDM sensitization. We studied three techniques to eliminate HDM from soft toys, namely freezing, hot tumble drying and washing with eucalyptus oil. Thirty-six toys (12 in each treatment group) were enumerated for live HDM by the heat escape method before and after freezing overnight, hot tumble drying for 1 h and washing in 0.2% to 0.4% eucalyptus oil. Freezing, hot tumble drying and washing with eucalyptus oil resulted in significant reductions in live HDM, an average reduction of 95.1%, 89.1% and 95.1%, respectively. Additionally, washing with eucalyptus oil resulted in a significant reduction in HDM allergens as well from a geometric mean of 9.12 μg/g to 0.37 μg/g (p = 0.033). These three HDM elimination techniques give parents of infants effective and acceptable methods of limiting HDM exposure.

  4. Effects of washing produce contaminated with the snail and slug hosts of Angiostrongylus cantonensis with three common household solutions.

    PubMed

    Yeung, Norine W; Hayes, Kenneth A; Cowie, Robert H

    2013-06-01

    The emerging infectious disease angiostrongyliasis (rat lungworm disease) is caused by ingesting snails and slugs infected by the nematode Angiostrongylus cantonensis. The definitive hosts of A. cantonensis are rats and the obligatory intermediate hosts are slugs and snails. Many cases result from accidentally ingesting infected snails or slugs on produce (eg, lettuce). This study assessed three readily available household products as washing solutions for removing snails and slugs from produce (romaine lettuce) to lower the probability of accidentally ingesting them. The solutions were acetic acid (vinegar), sodium hypochlorite (bleach), and sodium chloride (domestic salt). Snail and slug species known to be intermediate hosts and that are common in the Hawaiian Islands were used in the experiments: the alien snail Succinea tenella, the alien semi-slug Parmarion martensi, and the alien slugs Veronicella cubensis and Deroceras laeve. None of the products was any more effective than washing and rinsing with tap water alone. Most snails and slugs were removed after treatment but some remained on the lettuce even after washing and rinsing the produce. Only washing, rinsing, and then rinsing each leaf individually resulted in complete removal of all snails and slugs. The study did not address removal of any remaining slime left by the snails and slugs, nor did it address killing of worms. PMID:23901391

  5. Potential of activated carbon to recover randomly-methylated-β-cyclodextrin solution from washing water originating from in situ soil flushing.

    PubMed

    Sniegowski, K; Vanhecke, M; D'Huys, P-J; Braeken, L

    2014-07-01

    Despite the overall high efficacy of cyclodextrins to accelerate the treatment of soil aquifer remediation by in-situ soil flushing, the use in practice remains limited because of the high costs of cyclodextrin and high concentrations needed to significantly reduce the treatment time. The current study tested the potential of activated carbon to treat washing water originating from soil flushing in order to selectively separate hydrocarbon contaminants from washing water containing cyclodextrin and subsequently reuse the cyclodextrin solution for reinfiltration. A high recovery of the cyclodextrin from the washing water would reduce the costs and would make the technique economically feasible for soil remediation. This study aimed to investigate whether cyclodextrin can pass through the activated carbon filter without reducing the cyclodextrin concentration when the contaminated washing water is treated and whether the presence of cyclodextrin negatively affects the purification potential of activated carbon to remove the organic pollutants from the pumped soil water. Lab-scale column experiments showed that with the appropriate activated carbon 100% of cyclodextrin (randomly-methylated-β-cyclodextrin) can be recovered from the washing water and that the effect on the efficiency of activated carbon to remove the hydrocarbon contaminants remains limited. These results show that additional field tests are useful to make in-situ soil flushing with cyclodextrin both a technical and an economical interesting technique. These results might stimulate the application of cyclodextrin in soil treatment technology.

  6. Toxicological assessment and management options for boat pressure-washing wastewater.

    PubMed

    Gerić, Marko; Gajski, Goran; Oreščanin, Višnja; Kollar, Robert; Franekić, Jasna; Garaj-Vrhovac, Vera

    2015-04-01

    Boats are washed periodically for maintenance in order to remove biofoulants from hulls, which results in the generation of wastewater. This study aimed at evaluating the cyto/genotoxic and mutagenic properties of wastewater produced by pressure washing of boats. The chemical characterisation of this wastewater showed that Cu, Zn, V, Cr, Fe, Pb, and select organic contaminants exceeded the maximum allowable values from 1.7 up to 96 times. The wastewater produced negative effects on human lymphocytes resulting in decreased cell viability after 4 and 24h of exposure. Chromosome aberration, micronucleus, and comet assay parameters were significantly higher after 24h of exposure. At the same time, the Salmonella typhimurium test showed negative for both TA98 and TA100 strains at all of the concentrations tested. After the treatment of wastewater using electrochemical methods/ozonation during real scale treatment plant, removal rates of colour, turbidity and heavy metals ranged from 99.4% to 99.9%, while the removal of total organic carbon (TOC) and chemical oxygen demand (COD) was above 85%. This was reflected in the removal of the wastewater's cyto/genotoxicity, which was comparable to negative controls in all of the conducted tests, suggesting that such plants could be implemented in marinas to minimise human impact on marine systems.

  7. Toxicological assessment and management options for boat pressure-washing wastewater.

    PubMed

    Gerić, Marko; Gajski, Goran; Oreščanin, Višnja; Kollar, Robert; Franekić, Jasna; Garaj-Vrhovac, Vera

    2015-04-01

    Boats are washed periodically for maintenance in order to remove biofoulants from hulls, which results in the generation of wastewater. This study aimed at evaluating the cyto/genotoxic and mutagenic properties of wastewater produced by pressure washing of boats. The chemical characterisation of this wastewater showed that Cu, Zn, V, Cr, Fe, Pb, and select organic contaminants exceeded the maximum allowable values from 1.7 up to 96 times. The wastewater produced negative effects on human lymphocytes resulting in decreased cell viability after 4 and 24h of exposure. Chromosome aberration, micronucleus, and comet assay parameters were significantly higher after 24h of exposure. At the same time, the Salmonella typhimurium test showed negative for both TA98 and TA100 strains at all of the concentrations tested. After the treatment of wastewater using electrochemical methods/ozonation during real scale treatment plant, removal rates of colour, turbidity and heavy metals ranged from 99.4% to 99.9%, while the removal of total organic carbon (TOC) and chemical oxygen demand (COD) was above 85%. This was reflected in the removal of the wastewater's cyto/genotoxicity, which was comparable to negative controls in all of the conducted tests, suggesting that such plants could be implemented in marinas to minimise human impact on marine systems. PMID:25638522

  8. Evaluation of Postharvest Washing on Removal of Silver Nanoparticles (AgNPs) from Spinach Leaves.

    PubMed

    Zhang, Zhiyun; Guo, Huiyuan; Carlisle, Thomas; Mukherjee, Arnab; Kinchla, Amanda; White, Jason C; Xing, Baoshan; He, Lili

    2016-09-21

    There is increasing use of silver nanoparticles (AgNPs) as pesticides for fruits and vegetables due to the particles' unique antimicrobial and insecticidal properties. However, residual AgNPs in harvested produce may transfer through the food chain and pose a potential risk to public health. The objective of this study is to determine whether postharvest washing can effectively remove AgNPs that had accumulated on fresh produce. Ten microliters of commercially available 40 nm citrate coated AgNPs (0.4 mg/L) was dropped to a (1 × 1 cm(2)) spot on spinach leaves, followed by washing with deionized water (DI water), Tsunami 100 (80 mg/L), or Clorox bleach (200 mg/L). Then, the AgNP removal efficiency of the three treatments was evaluated by surface-enhanced Raman spectroscopy (SERS), scanning electron microscopy (SEM)-energy dispersive spectrometry (EDS), and inductively coupled plasma mass spectrometry (ICP-MS). ICP-MS results showed that deionized water removed statistically insignificant amounts of total Ag (5%), whereas Tsunami 100 and Clorox bleach yielded 21 and 10% decreases in total Ag, respectively (P < 0.05). The increased removal efficiency resulted from AgNP dissolution and Ag(+) release upon contact with the oxidizing agents in Tsunami 100 (peroxyacetic acid, hydrogen peroxide) and Clorox bleach (sodium hypochlorite). According to the SERS results, the deionized water and Tsunami 100 treatments removed nonsignificant amounts of AgNPs. Clorox bleach decreased Ag NPs by >90% (P < 0.05); however, SEM-EDS images revealed the formation of large silver chloride (AgCl) crystals (162 ± 51 nm) on the leaf, which explained the low total Ag removal from ICP-MS. This study indicates current factory washing methods for fresh produce may not be effective in reducing AgNPs (by water and Tsunami 100) and total Ag (by all three means). This highlights the necessity to develop an efficient washing method for NP removal from food surfaces in the future. PMID:27548506

  9. A Comparative Study of Induced Sputum and Bronchial Washings in Diagnosing Sputum Smear Negative Pulmonary Tuberculosis

    PubMed Central

    Mandava, Venu; Namballa, Usha Rani; Makala, Sravani

    2016-01-01

    Introduction Tuberculosis is one of the most important public health problem worldwide. Detecting patients with active pulmonary Koch’s disease is an important component of tuberculosis control programs. However, at times in patients even with a compatible clinical picture, sputum smears do not reveal acid-fast bacilli and smear-negative pulmonary tuberculosis remains a common problem. Aim The present study is aimed to compare the results of induced sputum and bronchial washings smear in patients suspected to have sputum smear negative pulmonary tuberculosis. Materials and Methods A prospective study conducted from August 2014 to July 2015, comprising 120 patients fulfilling study criteria. Patients with respiratory symptoms and chest roentgenogram suspicious of pulmonary tuberculosis with no previous history of anti-tuberculosis treatment and two spontaneous sputum smear samples negative for acid fast bacilli were included. Patients with active haemoptysis and sputum positive were excluded from the study. Sputum induction was done by using 5-10 ml of 3% hypertonic saline through ultrasonic nebulizer taking safety precautions. All the patient underwent fibreoptic bronchoscopy after six hours fasting on the same day. About 20 ml of normal saline instilled into the suspected pathology area and washings were taken with gentle suction. The sample processing and fluorescent staining for acid fast bacilli was done in a designated microscopy lab. Results Out of 120 sputum smear negative pulmonary tuberculosis patients, induced sputum smear examination detected acid fast bacilli in 76 patients (63.3%) and acid fast bacilli detected from bronchial washings in 94 patients (78.3%). Smear positivity was higher in cavitary and infiltrative lesions as compared to consolidation and infrahilar pattern disease. Conclusion Even though both induced sputum and bronchial washings procedures were valuable for the diagnosis of sputum smear negative, sputum induction with hypertonic

  10. Evaluation of Postharvest Washing on Removal of Silver Nanoparticles (AgNPs) from Spinach Leaves.

    PubMed

    Zhang, Zhiyun; Guo, Huiyuan; Carlisle, Thomas; Mukherjee, Arnab; Kinchla, Amanda; White, Jason C; Xing, Baoshan; He, Lili

    2016-09-21

    There is increasing use of silver nanoparticles (AgNPs) as pesticides for fruits and vegetables due to the particles' unique antimicrobial and insecticidal properties. However, residual AgNPs in harvested produce may transfer through the food chain and pose a potential risk to public health. The objective of this study is to determine whether postharvest washing can effectively remove AgNPs that had accumulated on fresh produce. Ten microliters of commercially available 40 nm citrate coated AgNPs (0.4 mg/L) was dropped to a (1 × 1 cm(2)) spot on spinach leaves, followed by washing with deionized water (DI water), Tsunami 100 (80 mg/L), or Clorox bleach (200 mg/L). Then, the AgNP removal efficiency of the three treatments was evaluated by surface-enhanced Raman spectroscopy (SERS), scanning electron microscopy (SEM)-energy dispersive spectrometry (EDS), and inductively coupled plasma mass spectrometry (ICP-MS). ICP-MS results showed that deionized water removed statistically insignificant amounts of total Ag (5%), whereas Tsunami 100 and Clorox bleach yielded 21 and 10% decreases in total Ag, respectively (P < 0.05). The increased removal efficiency resulted from AgNP dissolution and Ag(+) release upon contact with the oxidizing agents in Tsunami 100 (peroxyacetic acid, hydrogen peroxide) and Clorox bleach (sodium hypochlorite). According to the SERS results, the deionized water and Tsunami 100 treatments removed nonsignificant amounts of AgNPs. Clorox bleach decreased Ag NPs by >90% (P < 0.05); however, SEM-EDS images revealed the formation of large silver chloride (AgCl) crystals (162 ± 51 nm) on the leaf, which explained the low total Ag removal from ICP-MS. This study indicates current factory washing methods for fresh produce may not be effective in reducing AgNPs (by water and Tsunami 100) and total Ag (by all three means). This highlights the necessity to develop an efficient washing method for NP removal from food surfaces in the future.

  11. Apparatus for washing particulate material. [Removal of silicone oil from microspheres by trichloroethylene

    DOEpatents

    Rivera, A.L.; Fowler, V.L.; Justice, G.V.

    1983-12-29

    Transport of nuclear fuel microspheres through a wash liquid is facilitated by feeding a slurry containing the microspheres into the wash liquid via a column having a vibrating tubular screen located under its lower end.

  12. COMPILATION OF LABORATORY SCALE ALUMINUM WASH AND LEACH REPORT RESULTS

    SciTech Connect

    HARRINGTON SJ

    2011-01-06

    This report compiles and analyzes all known wash and caustic leach laboratory studies. As further data is produced, this report will be updated. Included are aluminum mineralogical analysis results as well as a summation of the wash and leach procedures and results. Of the 177 underground storage tanks at Hanford, information was only available for five individual double-shell tanks, forty-one individual single-shell tanks (e.g. thirty-nine 100 series and two 200 series tanks), and twelve grouped tank wastes. Seven of the individual single-shell tank studies provided data for the percent of aluminum removal as a function of time for various caustic concentrations and leaching temperatures. It was determined that in most cases increased leaching temperature, caustic concentration, and leaching time leads to increased dissolution of leachable aluminum solids.

  13. Effectiveness of a nonrinse, alcohol-free antiseptic hand wash.

    PubMed

    Moadab, A; Rupley, K F; Wadhams, P

    2001-06-01

    This study evaluated the efficacy of a novel surfactant, allantoin, and benzalkonium chloride hand sanitizer using the US Food and Drug Administration's method for testing antiseptic hand washes that podiatric physicians and other health-care personnel use. The alcohol-free product, HandClens, was compared with an alcohol-based product, Purell. Independent researchers from the California College of Podiatric Medicine conducted the study using 40 volunteer students from the class of 2001. The results show that HandClens outperformed Purell and met the regulatory requirements for a hand sanitizer. Purell failed as an antimicrobial hand wash and was less effective than a control soap used in the study. PMID:11420346

  14. Effect of soil washing with only chelators or combining with ferric chloride on soil heavy metal removal and phytoavailability: Field experiments.

    PubMed

    Guo, Xiaofang; Wei, Zebin; Wu, Qitang; Li, Chunping; Qian, Tianwei; Zheng, Wei

    2016-03-01

    In a field experiment on multi-metal contaminated soil, we investigated the efficiency of Cd, Pb, Zn, and Cu removal by only mixture of chelators (MC) or combining with FeCl3. After washing treatment, a co-cropping system was performed for heavy metals to be extracted by Sedum alfredii and to produce safe food from Zea mays. We analyzed the concentration of heavy metals in groundwater to evaluate the leashing risk of soil washing with FeCl3 and MC. Results showed that addition of FeCl3 was favorable to the removal of heavy metals in the topsoil. Metal leaching occurred mainly in rain season during the first co-cropping. The removal rates of Cd, Zn, Pb, and Cu in topsoil were 28%, 53%, 41%, and 21% with washing by FeCl3+MC after first harvest. The application of FeCl3 reduced the yield of S. alfredii and increased the metals concentration of Z. mays in first harvest. However, after amending soil, the metals concentration of Z. mays in FeCl3+MC treatment were similar to that only washing by MC. The grains and shoots of Z. mays were safe for use in feed production. Soil washing did not worsen groundwater contamination during the study period. But the concentration of Cd in groundwater was higher than the limit value of Standard concentrations for Groundwater IV. This study suggests that soil washing using FeCl3 and MC for the remediation of multi-metal contaminated soil is potential feasibility. However, the subsequent measure to improve the washed soil environment for planting crop is considered.

  15. Inactivation of viruses using novel protein A wash buffers.

    PubMed

    Bolton, Glen R; Selvitelli, Keith R; Iliescu, Ionela; Cecchini, Douglas J

    2015-01-01

    Low pH viral inactivation is typically performed in the eluate pool following the protein A capture step during the manufacturing of monoclonal antibodies and Fc-fusion proteins. However, exposure to low pH has the potential to alter protein quality. To avoid these difficulties, novel wash buffers capable of inactivating viruses while antibodies or Fc-fusion proteins were bound to protein A or mixed mode resins were developed. By equilibrating the column in high salt buffer (2 M ammonium sulfate or 3 M sodium chloride) after loading, the hydrophobic interactions between antibodies and protein A ligands were increased enough to prevent elution at pH 3. The ammonium sulfate was also found to cause binding of an antibody to a mixed mode cation exchange and a mixed mode anion exchange resin at pH values that caused elution in conventional cation and anion exchange resins (pH 3.5 for Capto Adhere and pH 8.0 for Capto MMC), indicating that retention was due to enhanced hydrophobic interactions. The potential of the 2 M ammonium sulfate pH 3 buffer, a 1 M arginine buffer, and a buffer containing the detergent LDAO to inactivate XMuLV virus when used as protein A wash buffers with a 1 hour contact time were studied. The high salt and detergent containing wash buffers provided about five logs of removal, determined using PCR, and complete combined removal and inactivation (> 6 logs), determined by measuring infectivity. The novel protein A washes could provide more rapid, automated viral inactivation steps with lower pool conductivities.

  16. 33 CFR 157.162 - Crude oil washing during a voyage.

    Code of Federal Regulations, 2011 CFR

    2011-07-01

    ... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Crude oil washing during a voyage... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.162 Crude oil washing... § 157.10c(b)(2) shall ensure that each cargo tank that is crude oil washed during a voyage other than...

  17. 33 CFR 157.162 - Crude oil washing during a voyage.

    Code of Federal Regulations, 2010 CFR

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Crude oil washing during a voyage... OIL IN BULK Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.162 Crude oil washing... § 157.10c(b)(2) shall ensure that each cargo tank that is crude oil washed during a voyage other than...

  18. Hand Washing Practices Among Emergency Medical Services Providers

    PubMed Central

    Bucher, Joshua; Donovan, Colleen; Ohman-Strickland, Pamela; McCoy, Jonathan

    2015-01-01

    Introduction Hand hygiene is an important component of infection control efforts. Our primary and secondary goals were to determine the reported rates of hand washing and stethoscope cleaning in emergency medical services (EMS) workers, respectively. Methods We designed a survey about hand hygiene practices. The survey was distributed to various national EMS organizations through e-mail. Descriptive statistics were calculated for survey items (responses on a Likert scale) and subpopulations of survey respondents to identify relationships between variables. We used analysis of variance to test differences in means between the subgroups. Results There were 1,494 responses. Overall, reported hand hygiene practices were poor among pre-hospital providers in all clinical situations. Women reported that they washed their hands more frequently than men overall, although the differences were unlikely to be clinically significant. Hygiene after invasive procedures was reported to be poor. The presence of available hand sanitizer in the ambulance did not improve reported hygiene rates but improved reported rates of cleaning the stethoscope (absolute difference 0.4, p=0.0003). Providers who brought their own sanitizer were more likely to clean their hands. Conclusion Reported hand hygiene is poor amongst pre-hospital providers. There is a need for future intervention to improve reported performance in pre-hospital provider hand washing. PMID:26587098

  19. Generation of chlorine by-products in simulated wash water.

    PubMed

    Shen, Cangliang; Norris, Pauline; Williams, Olivia; Hagan, Stephanie; Li, KaWang

    2016-01-01

    Free chlorine (FC) reacting with organic matter in wash water promotes the formation of chlorine by-products. This study aims to evaluate the dynamic impact of FC and organic load on the generation of haloacetic acids (HAAs) and trihalomethanes (THMs) in simulated wash water. Lettuce juice was sequentially added into FC solution with FC periodically replenished. Water samples were collected after each lettuce juice addition to measure water qualities and determine HAAs and THMs using US-Environmental-Protection-Agency (EPA) methods. Concentrations of 88-2103 μg/l of total HAAs and 20.79-859.47 μg/l of total THMs were detected during the study. Monobromoacetic, tribromoacetic, chlorodibromoacetic and trichloroacetic acid were the major HAAs components. Chloroform (trichloromethane) was the primary THMs present. A significant correlation of HAAs with chemical oxygen demand and THMs with FC was observed. Results indicated that optimizing wash water sanitizing systems to limit organic matters and maintain minimal effective FC concentration is critical.

  20. Recovery of MSWI and soil washing residues as concrete aggregates.

    PubMed

    Sorlini, Sabrina; Abbà, Alessandro; Collivignarelli, Carlo

    2011-02-01

    The aim of the present work was to study if municipal solid waste incinerator (MSWI) residues and aggregates derived from contaminated soil washing could be used as alternative aggregates for concrete production. Initially, chemical, physical and geometric characteristics (according to UNI EN 12620) of municipal solid waste incineration bottom ashes and some contaminated soils were evaluated; moreover, the pollutants release was evaluated by means of leaching tests. The results showed that the reuse of pre-treated MSWI bottom ash and washed soil is possible, either from technical or environmental point of view, while it is not possible for the raw wastes. Then, the natural aggregate was partially and totally replaced with these recycled aggregates for the production of concrete mixtures that were characterized by conventional mechanical and leaching tests. Good results were obtained using the same dosage of a high resistance cement (42.5R calcareous Portland cement instead of 32.5R); the concrete mixture containing 400 kg/m(3) of washed bottom ash and high resistance cement was classified as structural concrete (C25/30 class). Regarding the pollutants leaching, all concrete mixtures respected the limit values according to the Italian regulation. PMID:20537523