New carbocyclic nucleoside analogues with a bicyclo[2.2.1]heptane fragment as sugar moiety; synthesis, X-ray crystallography and anticancer activity.

PubMed

Tănase, Constantin I; Drăghici, Constantin; Căproiu, Miron Teodor; Shova, Sergiu; Mathe, Christophe; Cocu, Florea G; Enache, Cristian; Maganu, Maria

2014-01-01

An amine group was synthesized starting from an optically active bicyclo[2.2.1]heptane compound, which was then used to build the 5 atoms ring of a key 6-chloropurine intermediate. This was then reacted with ammonia and selected amines obtaining new adenine- and 6-substituted adenine conformationally constrained carbocyclic nucleoside analogues with a bicyclo[2.2.1]heptane skeleton in the sugar moiety. X-ray crystallography confirmed an exo-coupling of base to the ring and a L configuration of the nucleoside analogues. The compounds were tested for anticancer activity. Copyright © 2013 Elsevier Ltd. All rights reserved.

Injection Principles from Combustion Studies in a 200-Pound-Thrust Rocket Engine Using Liquid Oxygen and Heptane

NASA Technical Reports Server (NTRS)

Heidmann, M. F.; Auble, C. M.

1955-01-01

The importance of atomizing and mixing liquid oxygen and heptane was studied in a 200-pound-thrust rocket engine. Ten injector elements were used with both steel and transparent chambers. Characteristic velocity was measured over a range of mixture ratios. Combustion gas-flow and luminosity patterns within the chamber were obtained by photographic methods. The results show that, for efficient combustion, the propellants should be both atomized and mixed. Heptane atomization controlled the combustion rate to a much larger extent than oxygen atomization. Induced mixing, however, was required to complete combustion in the smallest volume. For stable, high-efficiency combustion and smooth engine starts, mixing after atomization was most promising.

Analysis Of MSL-1 Measurements Of Heptane Droplet Combustion

NASA Technical Reports Server (NTRS)

Ackerman, Malissa; Williams, Forman

2003-01-01

A droplet combustion experiment (DCE) was performed on the MSL-1 mission of the Space Shuttle Columbia. There were two flights of this mission - STS-83 in April of 1997 and STS-94 in July of 1997. The reflight occurred because a fuel-cell power problem onboard the shuttle forced an early termination of the first flight; this was the only shuttle mission to be flown twice. DCE data were obtained during both flights. A fiber-supported droplet combustion (FSDC) experiment also was run on STS-94. This smaller 'glovebox' experiment, which investigated the combustion of fiber-supported droplets in Spacelab cabin air, had previously flown on the first United States Microgravity Laboratory (USML-1) mission of STS-73, but successful measurements with heptane as the fuel in this experiment were first obtained on STS-94. Although heptane droplet combustion in convective flow also was studied on STS-94, only data without forced convection are considered here. The objective of the present paper is to analyze the results on heptane droplet combustion in quiescent atmospheres.

An Experimental Study of n-Heptane and JP-7 Extinction Limits in an Opposed Jet Burner

NASA Technical Reports Server (NTRS)

Convery, Janet L.; Pellett, Gerald L.; O'Brien, Walter F., Jr.; Wilson, Lloyd G.; Williams, John

2005-01-01

Propulsion engine combustor design and analysis requires experimentally verified data on the chemical kinetics of fuel. Among the important data is the combustion extinction limit as measured by observed maximum flame strain rate. The extinction limit relates to the ability to maintain a flame in a combustor during operation. Extinction limit data can be obtained for a given fuel by means of a laminar flame experiment using an opposed jet burner (OJB). Laminar extinction limit data can be applied to the turbulent application of a combustor via laminar flamelet modeling. The OJB consists of two axi-symmetric tubes (one for fuel and one for oxidizer), which produce a flat, disk-like counter-flow diffusion flame. This paper presents results of experiments to measure extinction limits for n-heptane and the military specification fuel JP-7, obtained from an OJB. JP-7 is an Air Force-developed fuel that continues to be important in the area of hypersonics. Because of its distinct properties it is currently the hydrocarbon fuel of choice for use in Scramjet engines. This study provides much-desired data for JP-7, for which very little information previously existed. The interest in n-heptane is twofold. First, there has been a significant amount of previous extinction limit study and resulting data with this fuel. Second, n-heptane (C7H16) is a pure substance, and therefore does not vary in composition as does JP-7, which is a mixture of several different hydrocarbons. These two facts allow for a baseline to be established by comparing the new OJB results to those previously taken. Additionally, the data set for n-heptane, which previously existed for mixtures up to 26 mole percent in nitrogen, is completed up to 100% n-heptane. The extinction limit data for the two fuels are compared, and complete experimental results are included.

EFFECTS OF EQUIVALENCE RATIO ON SPECIES AND SOOT CONCENTRATIONS IN PREMIXED N-HEPTANE FLAMES. (R828193)

EPA Science Inventory

The micro-structure of laminar premixed, atmospheric-pressure, fuel-rich flames of n-heptane/oxygen/argon has been studied at two equivalence ratios (C/O = 0.63 and C/O = 0.67). A heated quartz microprobe coupled to an online gas chromatography/mass spectrometry (HP 5890 Serie...

Analysis of extractables from one euphorbia

DOE Office of Scientific and Technical Information (OSTI.GOV)

Nemethy, E.K.; Otvos, J.W.; Calvin, M.

1979-12-01

Chemical analyses have been made of the heptane extractable material of Euphorbia lathyris, a plant which has been proposed as an energy farm candidate. The heptane extract is 4 to 5% of the dry plant weight and has a heat value of approx. 18 x 10/sup 3/ Btu/lb. This reduced photosynthetic material consists almost entirely of polycyclic triterpenoids. 2 figures, 4 tables.

Molecular mechanism of carbon nanotube to activate Subtilisin Carlsberg in polar and non-polar organic media

NASA Astrophysics Data System (ADS)

Zhang, Liyun; Li, Yuzhi; Yuan, Yuan; Jiang, Yuanyuan; Guo, Yanzhi; Li, Menglong; Pu, Xuemei

2016-11-01

In the work, we mainly used molecular dynamics (MD) simulation and protein structure network (PSN) to study subtilisin Carlsberg (SC) immobilized onto carbon nanotube (CNT) in water, acetonitrile and heptane solvents, in order to explore activation mechanism of enzymes in non-aqueous media. The result indicates that the affinity of SC with CNT follows the decreasing order of water > acetonitrile > heptane. The overall structure of SC and the catalytic triad display strong robustness to the change of environments, responsible for the activity retaining. However, the distances between two β-strands of substrate-binding pocket are significantly expanded by the immobilization in the increasing order of water < acetonitrile < heptane, contributing to the highest substrate-binding energy in heptane media. PSN analysis further reveals that the immobilization enhances structural communication paths to the substrate-binding pocket, leading to its larger change than the free-enzymes. Interestingly, the increase in the number of the pathways upon immobilization is not dependent on the absorbed extent but the desorbed one, indicating significant role of shifting process of experimental operations in influencing the functional region. In addition, some conserved and important hot-residues in the paths are identified, providing molecular information for functional modification.

Ascorbyl radical disproportionation in reverse micellar systems

NASA Astrophysics Data System (ADS)

Gębicki, J. L.; Szymańska-Owczarek, M.; Pacholczyk-Sienicka, B.; Jankowski, S.

2018-04-01

Ascorbyl radical was generated by the pulse radiolysis method and observed with the fast kinetic spectrophotometry within reverse micelles stabilized by AOT in n-heptane or by Igepal CO-520 in cyclohexane at different water to surfactant molar ratio, w0. Rate constants for the disproportionation of the ascorbyl radicals were smaller than those for intermicellar exchange for both type of reverse micelles and slower than those in homogeneous aqueous solutions. However, they increased with increasing w0 for AOT/n-heptane system, while they decreased for Igepal CO-520 system. The absorption spectra of ascorbic acid AOT/n-heptane reverse micellar system showed that the "pH" sensed by this molecule is lower than that in respective homogeneous aqueous solutions. The obtained results were rationalized taking into account three main factors (i) preferential location of ascorbic acid molecules in the interfacial region of the both types of reverse micelles; (ii) postulate that the pH of the interface is lower than that of the water pool of reverse micelles and (iii) different structure of the interface of the reverse micelles made by AOT in n-heptane and those formed by Igepal CO-520 I cyclohexane. Some possible consequences of these findings are discussed.

Separation of Nitration By-Products in Commercial-Grade Trinitro-Toluene by High Performance Liquid Chromatography.

DTIC Science & Technology

1982-06-01

Columns Columns used were:- Alltech 10 micron Silica 250 mm x 4.6 - I.D. Alltech 10 micron C18 Reverse-Phase 250 a x 4.6 mm I.D. Excalibar 10 micron...column with dichloromethane/n-heptane eluent. Ethyl acetate/n-heptane eluent has the advantage that it does not require flushing out at the end of each

Numerical investigation of spontaneous flame propagation under RCCI conditions

DOE PAGES

Bhagatwala, Ankit V; Sankaran, Ramanan; Kokjohn, Sage; ...

2015-06-30

This paper presents results from one and two-dimensional direct numerical simulations under Reactivity Controlled Compression Ignition (RCCI) conditions of a primary reference fuel (PRF) mixture consisting of n-heptane and iso-octane. RCCI uses in-cylinder blending of two fuels with different autoignition characteristics to control combustion phasing and the rate of heat release. These simulations employ an improved model of compression heating through mass source/sink terms developed in a previous work by Bhagatwala et al. (2014), which incorporates feedback from the flow to follow a predetermined experimental pressure trace. Two-dimensional simulations explored parametric variations with respect to temperature stratification, pressure profiles andmore » n-heptane concentration. Furthermore, statistics derived from analysis of diffusion/reaction balances locally normal to the flame surface were used to elucidate combustion characteristics for the different cases. Both deflagration and spontaneous ignition fronts were observed to co-exist, however it was found that higher n-heptane concentration provided a greater degree of flame propagation, whereas lower n-heptane concentration (higher fraction of iso-octane) resulted in more spontaneous ignition fronts. A significant finding was that simulations initialized with a uniform initial temperature and a stratified n-heptane concentration field, resulted in a large fraction of combustion occurring through flame propagation. The proportion of spontaneous ignition fronts increased at higher pressures due to shorter ignition delay when other factors were held constant. For the same pressure and fuel concentration, the contribution of flame propagation to the overall combustion was found to depend on the level of thermal stratification, with higher initial temperature gradients resulting in more deflagration and lower gradients generating more ignition fronts. Statistics of ignition delay are computed to assess the Zel’dovich (1980) theory for the mode of combustion propagation based on ignition delay gradients.« less

Probing Immobilization Mechanism of alpha-chymotrypsin onto Carbon Nanotube in Organic Media by Molecular Dynamics Simulation

PubMed Central

Zhang, Liyun; Xiao, Xiuchan; Yuan, Yuan; Guo, Yanzhi; Li, Menglong; Pu, Xuemei

2015-01-01

The enzyme immobilization has been adopted to enhance the activity and stability of enzymes in non-aqueous enzymatic catalysis. However, the activation and stabilization mechanism has been poorly understood on experiments. Thus, we used molecular dynamics simulation to study the adsorption of α-chymotrypsin (α-ChT) on carbon nanotube (CNT) in aqueous solution and heptane media. The results indicate that α-ChT has stronger affinity with CNT in aqueous solution than in heptane media, as confirmed by more adsorption atoms, larger contact area and higher binding free energies. Although the immobilization causes significant structure deviations from the crystal one, no significant changes in secondary structure of the enzyme upon adsorption are observed in the two media. Different from aqueous solution, the stabilization effects on some local regions far from the surface of CNT were observed in heptane media, in particular for S1 pocket, which should contribute to the preservation of specificity reported by experiments. Also, CNT displays to some extent stabilization role in retaining the catalytic H-bond network of the active site in heptane media, which should be associated with the enhanced activity of enzymes. The observations from the work can provide valuable information for improving the catalytic properties of enzymes in non-aqueous media. PMID:25787884

Model for the partition of neutral compounds between n-heptane and formamide.

PubMed

Karunasekara, Thushara; Poole, Colin F

2010-04-01

Partition coefficients for 84 varied compounds were determined for n-heptane-formamide biphasic partition system and used to derive a model for the distribution of neutral compounds between the n-heptane-rich and formamide-rich layers. The partition coefficients, log K(p), were correlated through the solvation parameter model giving log K(p)=0.083+0.559E-2.244S-3.250A-1.614B+2.387V with a multiple correlation coefficient of 0.996, standard error of the estimate 0.139, and Fisher statistic 1791. In the model, the solute descriptors are excess molar refraction, E, dipolarity/polarizability, S, overall hydrogen-bond acidity, A, overall hydrogen-bond basicity, B, and McGowan's characteristic volume, V. The model is expected to be able to estimate further values of the partition coefficient to about 0.13 log units for the same descriptor space covered by the calibration compounds (E=-0.26-2.29, S=0-1.93, A=0-1.25, B=0.02-1.58, and V=0.78-2.50). The n-heptane-formamide partition system is shown to have different selectivity to other totally organic biphasic systems and to be suitable for estimating descriptor values for compounds of low water solubility and/or stability.

Narcotic Tolerance and Dependence Mechanism: A Neurological Correlate.

DTIC Science & Technology

1977-05-01

chromatin proteins as substrate. Additional histone, 40 ug/0.2 ml did not increase the amount of !-(32P)ATP incorporation. However, additional casein (40...materials. Since casein is not a natural component of brain tissue, the significance of the stimulation of phosphorylation is unclear. There is no...radioactivity at the interface and heptane phase but the ,radioactivity in heptane was negligible. The degree of the partition from the aqueous micelles to the

Steam reforming of heptane in a fluidized bed membrane reactor

NASA Astrophysics Data System (ADS)

Rakib, Mohammad A.; Grace, John R.; Lim, C. Jim; Elnashaie, Said S. E. H.

n-Heptane served as a model compound to study steam reforming of naphtha as an alternative feedstock to natural gas for production of pure hydrogen in a fluidized bed membrane reactor. Selective removal of hydrogen using Pd 77Ag 23 membrane panels shifted the equilibrium-limited reactions to greater conversion of the hydrocarbons and lower yields of methane, an intermediate product. Experiments were conducted with no membranes, with one membrane panel, and with six panels along the height of the reactor to understand the performance improvement due to hydrogen removal in a reactor where catalyst particles were fluidized. Results indicate that a fluidized bed membrane reactor (FBMR) can provide a compact reformer for pure hydrogen production from a liquid hydrocarbon feedstock at moderate temperatures (475-550 °C). Under the experimental conditions investigated, the maximum achieved yield of pure hydrogen was 14.7 moles of pure hydrogen per mole of heptane fed.

Asphaltene aggregation and impact of alkylphenols.

PubMed

Goual, Lamia; Sedghi, Mohammad; Wang, Xiaoxiao; Zhu, Ziming

2014-05-20

The main objective of this study was to provide novel insights into the mechanism of asphaltene aggregation in toluene/heptane (Heptol) solutions and the effect of alkylphenols on asphaltene dispersion through the integration of advanced experimental and modeling methods. High-resolution transmission electron microscope (HRTEM) images revealed that the onset of asphaltene flocculation occurs near a toluene/heptane volume ratio of 70:30 and that flocculates are well below 1 μm in size. To assess the impact of alkylphenols on asphaltene aggregation, octylphenol (OP) and dodecylphenol (DP) were evaluated by impedance analysis based on their ability to delay the precipitation onset and to reduce the size of nonflocculated asphaltene aggregates in 80:20 toluene/heptane solutions. Although a longer dispersant chain length did not affect the precipitation onset, it reduced the size of the aggregates. Molecular dynamics simulations were then performed to understand the mechanism of interaction between a model asphaltene and OP in heptane. OP molecules saturated the H-bonding sites of asphaltenes and prevented them from interacting laterally between themselves. This explained why OP favored the formation of flocculates with filamentary rather than globular structures, which were clearly observed by HRTEM. Although OP proved to be an effective dispersant, its effectiveness was hindered by its self-association and the fact that it interacted at the periphery of asphaltenes, leaving their aromatic cores uncovered.

Structure of fenchone by broadband rotational spectroscopy

NASA Astrophysics Data System (ADS)

Loru, Donatella; Bermúdez, Miguel A.; Sanz, M. Eugenia

2016-08-01

The bicyclic terpenoid fenchone (C10H16O, 1,3,3-trimethylbicyclo[2.2.1]heptan-2-one) has been investigated by chirped pulse Fourier transform microwave spectroscopy in the 2-8 GHz frequency region. The parent species and all heavy atom isotopologues have been observed in their natural abundance. The experimental rotational constants of all isotopic species observed have been determined and used to obtain the substitution (rs) and effective (r0) structures of fenchone. Calculations at the B3LYP, M06-2X, and MP2 levels of theory with different basis sets were carried out to check their performance against experimental results. The structure of fenchone has been compared with those of norbornane (bicyclo[2.2.1]heptane) and the norbornane derivatives camphor (1,7,7-trimethylbicyclo[2.2.1]heptan-2-one) and camphene (3,3-dimethyl-2-methylenebicyclo[2.2.1]heptane), both with substituents at C2. The structure of fenchone is remarkably similar to those of camphor and camphene. Comparison with camphor allows identification of changes in ∠CCC angles due to the different position of the methyl groups. All norbornane derivatives display similar structural changes with respect to norbornane. These changes mainly affect the bond lengths and angles of the six-membered rings, indicating that the substituent at C2 drives structural adjustments to minimise ring strain after its introduction.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Loru, Donatella; Bermúdez, Miguel A.; Sanz, M. Eugenia

The bicyclic terpenoid fenchone (C{sub 10}H{sub 16}O, 1,3,3-trimethylbicyclo[2.2.1]heptan-2-one) has been investigated by chirped pulse Fourier transform microwave spectroscopy in the 2-8 GHz frequency region. The parent species and all heavy atom isotopologues have been observed in their natural abundance. The experimental rotational constants of all isotopic species observed have been determined and used to obtain the substitution (r{sub s}) and effective (r{sub 0}) structures of fenchone. Calculations at the B3LYP, M06-2X, and MP2 levels of theory with different basis sets were carried out to check their performance against experimental results. The structure of fenchone has been compared with those ofmore » norbornane (bicyclo[2.2.1]heptane) and the norbornane derivatives camphor (1,7,7-trimethylbicyclo[2.2.1]heptan-2-one) and camphene (3,3-dimethyl-2-methylenebicyclo[2.2.1]heptane), both with substituents at C{sub 2}. The structure of fenchone is remarkably similar to those of camphor and camphene. Comparison with camphor allows identification of changes in ∠CCC angles due to the different position of the methyl groups. All norbornane derivatives display similar structural changes with respect to norbornane. These changes mainly affect the bond lengths and angles of the six-membered rings, indicating that the substituent at C{sub 2} drives structural adjustments to minimise ring strain after its introduction.« less

Theoretical Basis for Estimated Test Times and Conditions for Drop Tower and Space-Based Droplet Burning Experiments With Methanol and N-Heptane

NASA Technical Reports Server (NTRS)

Marchese, Anthony J.; Dryer, Fredrick L.; Choi, Mun Y.

1994-01-01

In order to develop an extensive envelope of test conditions for NASA's space-based Droplet Combustion Experiment (DCE) as well those droplet experiments which can be performed using a drop tower, the transient vaporization and combustion of methanol and n-heptane droplets were simulated using a recently developed fully time-dependent, spherically symmetric droplet combustion model. The transient vaporization of methanol and n-heptane was modeled to characterize the instantaneous gas phase composition surrounding the droplet prior to the introduction of an ignition source. The results for methanol/air showed that the entire gas phase surrounding a 2 mm methanol droplet deployed in zero-g .quickly falls outside the lean flammability limit. The gas phase surrounding an identically-sized n-heptane droplet, on the other hand, remains flammable. The combustion of methanol was then modeled considering a detailed gas phase chemical kinetic mechanism (168 steps, 26 species) and the effect of the dissolution of flame-generated water into the liquid droplet. These results were used to determine the critical ignition diameter required to achieve quasi-steady droplet combustion in a given oxidizing environment. For droplet diameters greater than the critical ignition diameter, the model predicted a finite diameter at which the flame would extinguish. These extinction diameters were found to vary significantly with initial droplet diameter. This phenomenon appears to be unique to the transient heat transfer, mass transfer and chemical kinetics of the system and thus has not been reported elsewhere to date. The extinction diameter was also shown to vary significantly with the liquid phase Lewis number since the amount of water present in the droplet at extinction is largely governed by the rate at which water is transported into the droplet via mass diffusion. Finally, the numerical results for n-heptane combustion were obtained using both 2 step and 96 step semi-emperical chemical kinetic mechanisms. Neither mechanism exhibited the variation of extinction diameter with initial diameter.

(1R,4R,7S)-1,7-Dimethyl-7-(phenyl-sulfonyl-meth-yl)spiro-[bicyclo-[2.2.1]heptane-2,2'-1,3-dioxolane].

PubMed

Wang, Ya-Wen; Peng, Yu

2007-12-06

In the title compound, C(18)H(24)O(4)S, the chiral bicyclo-[2.2.1]heptane group is not symmetrical due to the influence of the substituents. The angle between the three-atom bridge plane and the four-atom planes of the boat-shaped six-membered ring are 55.07 (19) and 56.24 (19)°. The bridgehead angle is 92.75 (17)°.

Pervaporation separation of thiophene-heptane mixtures with polydimethylsiloxane (PDMS) membrane for desulfurization.

PubMed

Chen, Jian; Li, Jiding; Qi, Rongbin; Ye, Hong; Chen, Cuixian

2010-01-01

Cross-linked polydimethylsiloxane (PDMS)-polyetherimide (PEI) composite membranes were prepared, in which asymmetric microporous PEI membrane prepared with phase inversion method was acted as the microporous supporting layer in the flat-plate composite membrane. Membrane characterization was conducted by Fourier transform infrared and scanning electronic microscopy analysis. The composite membranes were employed in pervaporation separation of n-heptane-thiophene mixtures. Effect of amount of PDMS, cross-linking temperature, amount of cross-linking agent, and cross-linking time on the separation efficiency of n-heptane-thiophene mixtures was investigated experimentally. Experiment results demonstrated that 80-100 degrees degrees C of cross-linking temperature was more preferable for practical application, as the amount of cross-linking agent was up to 20 wt.%, and 25 wt.% of PDMS amount was more optimal as far as flux and sulfur enrichment factor were concerned. In addition, the swelling degree of and stableness of composite membrane during long-time operation were studied, which should be significant for practical application.

[Study of amount of evaporation residue in extracts from plastic kitchen utensils into four food-simulating solvents].

PubMed

Ohno, Hiroyuki; Suzuki, Masako; Kawamura, Yoko

2011-01-01

The amount of evaporation residue was investigated as an index of total amount of non-volatile substances that migrated from plastic kitchen utensils into four food-simulating solvents (water, 4% acetic acid, 20% ethanol and heptane). The samples were 71 products made of 12 types of plastics for food contact use. The amount was determined in accordance with the Japanese testing method. The quantitation limit was 5 µg/mL. In the cases of polyethylene, polypropylene, polystyrene, acrylonitrile styrene resin, acrylonitrile butadiene styrene resin, polyvinyl chloride, polyvinylidene chloride, polymethylpentene, polymethylmethacrylate and polyethylene terephthalate samples, the amount was highest for heptane and very low for the other solvents. On the other hand, in the cases of melamine resin and polyamide samples, the amount was highest for 4% acetic acid or 20% ethanol and lowest for heptane. These results enabled the selection of the most suitable solvent, and the rapid and efficient determination of evaporation residue.

In situ GISAXS study of a Si-containing block copolymer under solvent vapor annealing: Effects of molecular weight and solvent vapor composition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bai, W.; Yager, K. G.; Ross, C. A.

The room-temperature solvent vapor annealing of polystyrene-b-polydimethylsiloxane (PS-b-PDMS) block copolymer films was studied in situ by grazing incidence small-angle X-ray scattering. Films of cylinder-forming PS-b-PDMS with molecular weight 16 kg/mol and 12.2 kg/mol, annealed under vapors of toluene:heptane with varying composition, exhibited swelling-ratio-dependent evolution of microdomain spacing and orientation. In a vapor made from a toluene:heptane 5:1 volumetric ratio liquid mixture, or from pure toluene, cylindrical microdomains reoriented from majority out-of-plane to in-plane during annealing, while drying led to shrinkage along the film normal and a large distortion of the hexagonal lattice of in-plane cylinders. As a result, annealing undermore » vapor from a toluene:heptane 1:5 volumetric ratio liquid produced a non-bulk lamellar structure in the 16 kg/mol PS-b-PDMS.« less

Synthesis and application of magnetic deep eutectic solvents: Novel solvents for ultrasound assisted liquid-liquid microextraction of thiophene.

PubMed

Khezeli, Tahere; Daneshfar, Ali

2017-09-01

Two novel magnetic deep eutectic solvents (MDESs), comprised of cheap and simple components named [choline chloride/phenol] [FeCl 4 ] and [choline chloride/ethylene glycol] [FeCl 4 ] were prepared and characterized by CHN elemental analysis, proton nuclear magnetic resonance ( 1 H NMR), vibrating sample magnetometery (VSM), Raman, Fourier transform-infrared (FT-IR) and UV-Vis spectrometery. The extraction efficiency of the prepared MDESs has been investigated in ultrasound assisted liquid-liquid microextraction based MDES (UALLME-MDES). Briefly, MDESs were added to n-heptan containing thiophene. Then, MDESs were dispersed in n-heptane by sonication. After that, microdroplets of MDESs were collected by a magnet and the remained concentration of thiophene in n-heptane phase was analyzed by GC-FID. The results indicated that [choline chloride/phenol] [FeCl 4 ] has higher extraction efficiency than [choline chloride/ethylene glycol] [FeCl 4 ]. This work opens a new way to the application of MDESs. Copyright © 2016 Elsevier B.V. All rights reserved.

In situ GISAXS study of a Si-containing block copolymer under solvent vapor annealing: Effects of molecular weight and solvent vapor composition

DOE PAGES

Bai, W.; Yager, K. G.; Ross, C. A.

2016-08-19

The room-temperature solvent vapor annealing of polystyrene-b-polydimethylsiloxane (PS-b-PDMS) block copolymer films was studied in situ by grazing incidence small-angle X-ray scattering. Films of cylinder-forming PS-b-PDMS with molecular weight 16 kg/mol and 12.2 kg/mol, annealed under vapors of toluene:heptane with varying composition, exhibited swelling-ratio-dependent evolution of microdomain spacing and orientation. In a vapor made from a toluene:heptane 5:1 volumetric ratio liquid mixture, or from pure toluene, cylindrical microdomains reoriented from majority out-of-plane to in-plane during annealing, while drying led to shrinkage along the film normal and a large distortion of the hexagonal lattice of in-plane cylinders. As a result, annealing undermore » vapor from a toluene:heptane 1:5 volumetric ratio liquid produced a non-bulk lamellar structure in the 16 kg/mol PS-b-PDMS.« less

Mutual diffusion coefficients of heptane isomers in nitrogen: A molecular dynamics study

NASA Astrophysics Data System (ADS)

Chae, Kyungchan; Violi, Angela

2011-01-01

The accurate knowledge of transport properties of pure and mixture fluids is essential for the design of various chemical and mechanical systems that include fluxes of mass, momentum, and energy. In this study we determine the mutual diffusion coefficients of mixtures composed of heptane isomers and nitrogen using molecular dynamics (MD) simulations with fully atomistic intermolecular potential parameters, in conjunction with the Green-Kubo formula. The computed results were compared with the values obtained using the Chapman-Enskog (C-E) equation with Lennard-Jones (LJ) potential parameters derived from the correlations of state values: MD simulations predict a maximum difference of 6% among isomers while the C-E equation presents that of 3% in the mutual diffusion coefficients in the temperature range 500-1000 K. The comparison of two approaches implies that the corresponding state principle can be applied to the models, which are only weakly affected by the anisotropy of the interaction potentials and the large uncertainty will be included in its application for complex polyatomic molecules. The MD simulations successfully address the pure effects of molecular structure among isomers on mutual diffusion coefficients by revealing that the differences of the total mutual diffusion coefficients for the six mixtures are caused mainly by heptane isomers. The cross interaction potential parameters, collision diameter σ _{12}, and potential energy well depth \\varepsilon _{12} of heptane isomers and nitrogen mixtures were also computed from the mutual diffusion coefficients.

N-heptane decomposition in multi-needle to plate electrical discharge

NASA Astrophysics Data System (ADS)

Pekarek, Stanislav; Pospisil, Milan

2003-10-01

Plasma based technologies are becoming more and more important for destruction of volatile organic compounds in air streams. The most frequent electrical discharges tested for VOC decomposition are corona and dielectric barrier discharge. We proposed [1] multi-hollow needles to plate atmospheric pressure discharge enhanced by the flow of the mixture of air with VOC through the needles. In this case all reactive mixture will pass through the active zone of the discharge. The high-speed gas flow near the exit of the needle will also efficiently cool the electrodes. Hence the higher values of the discharge current can be obtained without the danger of the discharge transition to the spark. The chemical reactions leading to the VOC decomposition can therefore be enhanced [2]. We performed an experimental study of the n-heptane decomposition efficiency on its concentration in air in the input of the discharge. We choose n-heptane, an important part of organic solvents and part of automotive fuels, as a representative of saturated alkanes. We found that with decreasing n-heptane concentration the decomposition efficiency increases. Acknowledgement: This work was supported by the research program No: J04/98:212300016 "Pollution control and monitoring of the Environment" of the Czech Technical University in Prague. References [1] S. Pekárek, V. Køíha, M. Pospíil - J. Physics D, Appl. Physics, 34, 117 (2001). [2] O. Goosens, T. Callebaut, Y. Akishev, C. Leys - IEEE Trans. Plasma Sc. 30, 176 (2002).

Hydroperoxide Measurements During Low-Temperature Gas-Phase Oxidation of n-Heptane and n-Decane.

PubMed

Rodriguez, Anne; Herbinet, Olivier; Meng, Xiangzan; Fittschen, Christa; Wang, Zhandong; Xing, Lili; Zhang, Lidong; Battin-Leclerc, Frédérique

2017-03-09

A wide range of hydroperoxides (C 1 -C 3 alkyl hydroperoxides, C 3 -C 7 alkenyl hydroperoxides, C 7 ketohydroperoxides, and hydrogen peroxide (H 2 O 2 )), as well as ketene and diones, have been quantified during the gas-phase oxidation of n-heptane. Some of these species, as well as C 10 alkenyl hydroperoxides and ketohydroperoxides, were also measured during the oxidation of n-decane. These experiments were performed using an atmospheric-pressure jet-stirred reactor at temperatures from 500 to 1100 K and one of three analytical methods, time-of-flight mass spectrometry combined with tunable synchrotron photoionization with a molecular beam sampling: time-of-flight mass spectrometry combined with laser photoionization with a capillary tube sampling, continuous wave cavity ring-down spectroscopy with sonic probe sampling. The experimental temperature at which the maximum mole fraction is observed increases significantly for alkyl hydroperoxides, alkenyl hydroperoxides, and then more so again for hydrogen peroxide, compared to ketohydroperoxides. The influence of the equivalence ratio from 0.25 to 4 on the formation of these peroxides has been studied during n-heptane oxidation. The up-to-date detailed kinetic oxidation models for n-heptane and for n-decane found in the literature have been used to discuss the possible pathways by which these peroxides, ketene, and diones are formed. In general, the model predicts well the reactivity of the two fuels, as well as the formation of major intermediates.

(1R,4R,7S)-1,7-Dimethyl-7-(phenyl­sulfonyl­meth­yl)spiro­[bicyclo­[2.2.1]heptane-2,2′-1,3-dioxolane

PubMed Central

Wang, Ya-Wen; Peng, Yu

2008-01-01

In the title compound, C18H24O4S, the chiral bicyclo­[2.2.1]heptane group is not symmetrical due to the influence of the substituents. The angle between the three-atom bridge plane and the four-atom planes of the boat-shaped six-membered ring are 55.07 (19) and 56.24 (19)°. The bridgehead angle is 92.75 (17)°. PMID:21200933

Discovery, synthesis, selectivity modulation and DMPK characterization of 5-azaspiro[2.4]heptanes as potent orexin receptor antagonists.

PubMed

Stasi, Luigi Piero; Artusi, Roberto; Bovino, Clara; Buzzi, Benedetta; Canciani, Luca; Caselli, Gianfranco; Colace, Fabrizio; Garofalo, Paolo; Giambuzzi, Silvia; Larger, Patrice; Letari, Ornella; Mandelli, Stefano; Perugini, Lorenzo; Pucci, Sabrina; Salvi, Matteo; Toro, PierLuigi

2013-05-01

Starting from a orexin 1 receptor selective antagonist 4,4-disubstituted piperidine series a novel potent 5-azaspiro[2.4]heptane dual orexin 1 and orexin 2 receptor antagonist class has been discovered. SAR and Pharmacokinetic optimization of this series is herein disclosed. Lead compound 15 exhibits potent activity against orexin 1 and orexin 2 receptors along with low cytochrome P450 inhibition potential, good brain penetration and oral bioavailability in rats. Copyright © 2013 Elsevier Ltd. All rights reserved.

The effects of detailed chemistry and transport on microgravity droplet combustion

NASA Technical Reports Server (NTRS)

Marchese, A. J.; Lee, J. C.; Held, T. J.; Dryer, F. L.

1995-01-01

A brief overview of recent advances in the theoretical study of microgravity droplet combustion is presented. Much of this work has centered on the development and utilization of sphero-symmetric transient numerical models which consider detailed gas phase chemistry and transport as well as energy and/or species transport within a regressing condensed phase. Numerical results for microgravity combustion and vaporization of methanol, methanol/water, heptane, and heptane/hexadecane droplets are summarized along with refinements in chemical kinetics and the development of a new two-dimensional axi-symmetric model.

Chemical Durability Improvement and Static Fatigue of Glasses.

DTIC Science & Technology

1982-05-01

Specifically, the replacement of hydroxyl groups on the glass surface with silane or Grignard reagent nearly completely eliminated stress rate dependence...CK3SiC13 in Heptane solution Cc) 2 vol % (CR3)3SIC1 in Heptane solution (d) 0.1 M CH3MgBr ( Grignard reagent ) in n-Buthyl ether solution • Corning 7900...C113)3- SiCl or C13MgBr ( Grignard reagent ) solution while it remains practi- cally unchanged in CH3SiCI3 solution. In CH3SICI3 , the strength is

Persistence assessment of cyclohexyl- and norbornyl-derived ketones and their degradation products in different OECD screening tests.

PubMed

Seyfried, M; van Ginkel, C G; Boschung, A; Miffon, F; Fantini, P; Tissot, E; Baroux, L; Merle, P; Chaintreau, A

2015-07-01

The persistence of synthetic cyclohexyl- and norbornyl-derived ketones was assessed by using OECD 301F and 301D biodegradation tests. While cyclohexyl-derived ketones either reached or came close to the pass level (60%) after 60 d, the corresponding norbornyl derivatives yielded significantly less biodegradation (<40%). By analyzing extracts at 60 d, the key degradation products of four norbornyl derivatives were identified. Consistently, 2-bicyclo[2.2.1]heptane carboxylic acid was found as a principal degradation product with minor quantities of bicyclo[2.2.1]heptan-2-one and 2-bicyclo[2.2.1]heptane acetic acid. When the three degradation products were re-synthesized and tested individually for biodegradability, the former two were found to be ultimately biodegradable after 60 d in OECD 301D tests, thus proving non-persistence. Similarly, 2-bicyclo[2.2.1]heptane acetic acid was found to be degraded significantly, albeit with long lag phases exceeding 60 d in the case of freshwater inoculum, then ultimately reaching the pass level. On the other hand, norbornyl ketones were still only partially biodegradable in the same test. We conclude that despite the potential for ultimate biodegradation of norbornyl-derived ketones, current screening tests yield an incomplete picture of their biodegradability, particularly when applying strict OECD criteria. The appearance of long lag phases when re-testing norbornyl ketone degradation products underlines the importance of extending tests to well beyond 28 and even 60 d in the case of freshwater inocula. Copyright © 2015 Elsevier Ltd. All rights reserved.

Highly Efficient and Facile Photocatalytic Recycling System Suitable for ICAR ATRP of Hydrophilic Monomers.

PubMed

Jiang, Xiaowu; Zhang, Lifen; Cheng, Zhenping; Zhu, Xiulin

2016-08-01

Photoinduced initiators for continuous activator regeneration atom transfer radical polymerization (ATRP) of hydrophilic monomers in heptane/ethanol latent-biphasic system for copper catalyst separation and recycling have been realized for the first time at room temperature with different wavelengths of visible light LED (green, blue, purple, and white LED) as external stimulus, using 2-bromophenylacetate as the ATRP initiator and camphorquinone/triethylamine as the photoinitiator. In this system, hybrid catalyst complex (HCc) is synthesized as a novel nonpolar catalyst, which is preferentially dissolved in heptane. The hydrophilic polymers obtained catalyzed by HCc in heptane/ethanol mixture solvent show typical "living" features, for example, the values of Mn,GPC increase linearly with monomer conversion up to quantitative level (>96%) and the molecular weight distributions were kept narrow (Mw /Mn < 1.20) throughout the polymerization process. It should be noted that the excellent controllability of this novel polymerization system can be achieved even after 5 catalyst recycling experiments under LED irradiation. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Dynamic measurement of speed of sound in n-Heptane by ultrasonics during fuel injections.

PubMed

Minnetti, Elisa; Pandarese, Giuseppe; Evangelisti, Piersavio; Verdugo, Francisco Rodriguez; Ungaro, Carmine; Bastari, Alessandro; Paone, Nicola

2017-11-01

The paper presents a technique to measure the speed of sound in fuels based on pulse-echo ultrasound. The method is applied inside the test chamber of a Zeuch-type instrument used for indirect measurement of the injection rate (Mexus). The paper outlines the pulse-echo method, considering probe installation, ultrasound beam propagation inside the test chamber, typical signals obtained, as well as different processing algorithms. The method is validated in static conditions by comparing the experimental results to the NIST database both for water and n-Heptane. The ultrasonic system is synchronized to the injector so that time resolved samples of speed of sound can be successfully acquired during a series of injections. Results at different operating conditions in n-Heptane are shown. An uncertainty analysis supports the analysis of results and allows to validate the method. Experimental results show that the speed of sound variation during an injection event is less than 1%, so the Mexus model assumption to consider it constant during the injection is valid. Copyright © 2017 Elsevier B.V. All rights reserved.

Power and Thermal Technologies for Air and Space -- Scientific Research Program. Delivery Order 0016: Developing and Processing High Energy Density Polymer Film Dielectrics for High Temperature Air Force Power Electronic Applications

DTIC Science & Technology

2010-01-01

a vacuum controller. A vacuum of < 1 µ torr was achieved with a combination of a turbo pump and a scroll pump system. The sample probing is...the polymer was reprecipitated in heptane non-solvent. The filtered polymer was washed with heptane and was finally dried in vacuum at 100ºC for three...solution was added to a large excess of methanol to precipitate the polymer. After soxhlet extraction with methanol and vacuum drying, the polymer was

Droplet Combustion Experiments Aboard the International Space Station

NASA Astrophysics Data System (ADS)

Dietrich, Daniel L.; Nayagam, Vedha; Hicks, Michael C.; Ferkul, Paul V.; Dryer, Frederick L.; Farouk, Tanvir; Shaw, Benjamin D.; Suh, Hyun Kyu; Choi, Mun Y.; Liu, Yu Cheng; Avedisian, C. Thomas; Williams, Forman A.

2014-10-01

This paper summarizes the first results from isolated droplet combustion experiments performed on the International Space Station (ISS). The long durations of microgravity provided in the ISS enable the measurement of droplet and flame histories over an unprecedented range of conditions. The first experiments were with heptane and methanol as fuels, initial droplet droplet diameters between 1.5 and 5.0 m m, ambient oxygen mole fractions between 0.1 and 0.4, ambient pressures between 0.7 and 3.0 a t m and ambient environments containing oxygen and nitrogen diluted with both carbon dioxide and helium. The experiments show both radiative and diffusive extinction. For both fuels, the flames exhibited pre-extinction flame oscillations during radiative extinction with a frequency of approximately 1 H z. The results revealed that as the ambient oxygen mole fraction was reduced, the diffusive-extinction droplet diameter increased and the radiative-extinction droplet diameter decreased. In between these two limiting extinction conditions, quasi-steady combustion was observed. Another important measurement that is related to spacecraft fire safety is the limiting oxygen index (LOI), the oxygen concentration below which quasi-steady combustion cannot be supported. This is also the ambient oxygen mole fraction for which the radiative and diffusive extinction diameters become equal. For oxygen/nitrogen mixtures, the LOI is 0.12 and 0.15 for methanol and heptane, respectively. The LOI increases to approximately 0.14 (0.14 O 2/0.56 N 2/0.30 C O 2) and 0.17 (0.17 O 2/0.63 N 2/0.20 C O 2) for methanol and heptane, respectively, for ambient environments that simulated dispersing an inert-gas suppressant (carbon dioxide) into a nominally air (1.0 a t m) ambient environment. The LOI is approximately 0.14 and 0.15 for methanol and heptane, respectively, when helium is dispersed into air at 1 atm. The experiments also showed unique burning behavior for large heptane droplets. After the visible hot flame radiatively extinguished around a large heptane droplet, the droplet continued to burn with a cool flame. This phenomena was observed repeatably over a wide range of ambient conditions. These cool flames were invisible to the experiment imaging system but their behavior was inferred by the sustained quasi-steady burning after visible flame extinction. Verification of this new burning regime was established by both theoretical and numerical analysis of the experimental results. These innovative experiments have provided a wealth of new data for improving the understanding of droplet combustion and related aspects of fire safety, as well as offering important measurements that can be used to test sophisticated evolving computational models and theories of droplet combustion.

Emulsion Droplet Combustion in Microgravity: Water/Heptane Emulsions

NASA Technical Reports Server (NTRS)

Avedisian, C. Thomas

1997-01-01

This presentation reviews a series of experiments to further examine parametric effects on sooting processes of droplet flames in microgravity. The particular focus is on a fuel droplet emulsified with water, specifically emulsions of n-heptane as the fuel-phase and water as the dispersed phase. Water was selected as the additive because of its anticipated effect on soot formation, and the heptane fuel phase was chosen to theoretically reduce the likelihood of microexplosions because its boiling point is nearly the same as that of water: 100 C for water and 98 C for heptane. The water content was varied while the initial droplet diameter was kept within a small range. The experiments were carried out in microgravity to reduce the effects of buoyancy and to promote spherical symmetry in the burning process. Spherically symmetric droplet burning is a convenient starting point for analysis, but experimental data are difficult to obtain for this situation as evidenced by the fact that no quantitative data have been reported on unsupported emulsion droplet combustion in a convection-free environment. The present study improves upon past work carried out on emulsion droplet combustion in microgravity which employed emulsion droplets suspended from a fiber. The fiber can be instrusive to the emulsion droplet burning process as it can promote coalescence of the dispersed water phase and heterogeneous nucleation on the fiber. Prior work has shown that the presence of water in liquid hydrocarbons can have both beneficial and detrimental effects on the combustion process. Water is known to reduce soot formation and radiation heat transfer to combustor walls Gollahalli (1979) reduce flame temperatures and thereby NOx emissions, and encourage secondary droplet atomization or microexplosion. Water also tends to retard ignition and and promote early extinction. The former effect restricted the range of water volume fractions as discussed below.

Performance of a Small Internal Combustion Engine Using N-Heptane and Iso-Octane

DTIC Science & Technology

2010-03-01

evaluate the ON effects on a FUJI BF34-EI, small 4-stroke spark ignition engine as preliminary steps to using a military grade JP-8 jet turbine fuel ...K) Pcrit (MPa) HHV (kJ/kg) LHV (kJ/kg) n-Heptane C7H16 100.20 371.60 537.70 2.62 48,456 44,926 i-Octane C8H18 114.22 398.40 567.50 2.40 48,275 44,791...meter the fuel . The carburetor is equipped with both a high speed and low speed fuel jet . It is unknown what engine speed it switches from one to

High-quality Italian rice cultivars: chemical indices of ageing and aroma quality.

PubMed

Griglione, Alessandra; Liberto, Erica; Cordero, Chiara; Bressanello, Davide; Cagliero, Cecilia; Rubiolo, Patrizia; Bicchi, Carlo; Sgorbini, Barbara

2015-04-01

The volatile fractions of six Italian high-quality rice cultivars were investigated by HS-SPME-GC-MS to define fingerprinting and identify chemical markers and/or indices of ageing and aroma quality. In particular, four non-aromatic (Carnaroli, Carnise, Cerere and Antares) and two aromatic (Apollo and Venere) rices, harvested in 2010 and 2011, were monitored over 12months. Twenty-five aroma components were considered and, despite considerable inter-annual variability, some of them showed similar trends over time, including 2-(E)-octenal as a marker of ageing for all cultivars, and heptanal, octanal and 2-ethyl hexanol as cultivar-specific indicators. The area ratios 2-acetyl-1-pyrroline/1-octen-3-ol, for Venere, and 3-methyl-1-butanol/2-methyl-1-butanol, for Apollo, were also found to act as ageing indices. Additional information on release of key-aroma compounds was also obtained from quantitation and its dependence on grain shape and chemical composition. Heptanal/1-octen-3-ol and heptanal/octanal ratios were also defined as characterising the aroma quality indices of the six Italian rice cultivars investigated. Copyright © 2014 Elsevier Ltd. All rights reserved.

Catalyseur d'hydrocraquage à base de sulfure de NiMo déposé sur une zéolithe HEMT modifiée

NASA Astrophysics Data System (ADS)

Baalala, M.; Becue, T.; Leglise, J.; Manoli, J. M.; van Gestel, J. N. M.; Lamotte, J.; Bensitel, M.; Goupil, J. M.; Cornet, D.

1999-02-01

Treating a NH4EMT zeolite with a solution of (NH4)2SiF6 at 80 °C affords a solid containing amorphous SiO2 intimately mixed with the zeolite. This acidic support EMT-Si was loaded with NiMo sulfide in order to prepare a bifunctional catalyst, which was tested for the hydrogenation of benzene and the hydrocracking of n-heptane. This NiMo/EMT-Si catalyst was found more active for hydrogenation than the analogous NiMo/HY. This is ascribed to a higher dispersion of the NiMo sulfide, which is almost equally shared between the internal mesopores in the modified EMT solid, and the fissures, which were created throughout the zeolite grains upon inserting the NiMo sulfide. The catalyst with the EMT-Si support was also found more active than the NiMo/HY for the hydrocracking of heptane, with a slightly higher selectivity into heptane isomers. Le traitement d'une zéolithe NH4EMT par une solution de (NH4)2SiF6 fournit un solide comportant une phase SiO2 amorphe intimement mélangée aux parties intactes de la zéolithe. Sur ce support acide EMT-Si, on a greffé un sulfure de NiMo afin de préparer un catalyseur bifonctionnel qui a été testé dans les réactions d'hydrogénation du benzène et d'hydrocraquage du n-heptane. Ce catalyseur NiMo/EMT-Si s'avère plus actif en hydrogénation que son analogue NiMo/HY, en raison d'une meilleure dispersion du sulfure de NiMo. Sur le solide EMT modifié, le sulfure se répartit à peu près également entre les mésopores internes et les fissures crées dans les grains de zéolithe lors de l'insertion du sulfure de NiMo. Au contraire sur le support Y, une partie du sulfure est externe aux grains de zéolithe et inactive en catalyse. Le catalyseur NiMo/EMT-Si est aussi trouvé plus actif que le NiMo/HY en hydrocraquage du n-heptane, et un peu plus sélectif en isomères.

3D-QSAR studies on 1,2,4-triazolyl 5-azaspiro [2.4]-heptanes as D3R antagonists

NASA Astrophysics Data System (ADS)

Zhang, Xin; Zhang, Hui

2018-07-01

Dopamine D3 receptor has become an attractive target in the treatment of abused drugs. 3D-QSAR studies were performed on a novel series of D3 receptor antagonists, 1,2,4-triazolyl 5-azaspiro [2.4]-heptanes, using CoMFA and CoMSIA methods. Two predictive 3D-QSAR models have been generated for the modified design of D3R antagonists. Based on the steric, electrostatic, hydrophobic and hydrogen-bond acceptor information of contour maps, key structural factors affecting the bioactivity were explored. This work gives helpful suggestions on the design of novel D3R antagonists with increased activities.

Bottom-up coarse-grained models with predictive accuracy and transferability for both structural and thermodynamic properties of heptane-toluene mixtures

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, Nicholas J. H.; Noid, W. G., E-mail: wnoid@chem.psu.edu

This work investigates the promise of a “bottom-up” extended ensemble framework for developing coarse-grained (CG) models that provide predictive accuracy and transferability for describing both structural and thermodynamic properties. We employ a force-matching variational principle to determine system-independent, i.e., transferable, interaction potentials that optimally model the interactions in five distinct heptane-toluene mixtures. Similarly, we employ a self-consistent pressure-matching approach to determine a system-specific pressure correction for each mixture. The resulting CG potentials accurately reproduce the site-site rdfs, the volume fluctuations, and the pressure equations of state that are determined by all-atom (AA) models for the five mixtures. Furthermore, we demonstratemore » that these CG potentials provide similar accuracy for additional heptane-toluene mixtures that were not included their parameterization. Surprisingly, the extended ensemble approach improves not only the transferability but also the accuracy of the calculated potentials. Additionally, we observe that the required pressure corrections strongly correlate with the intermolecular cohesion of the system-specific CG potentials. Moreover, this cohesion correlates with the relative “structure” within the corresponding mapped AA ensemble. Finally, the appendix demonstrates that the self-consistent pressure-matching approach corresponds to minimizing an appropriate relative entropy.« less

Bottom-up coarse-grained models with predictive accuracy and transferability for both structural and thermodynamic properties of heptane-toluene mixtures.

PubMed

Dunn, Nicholas J H; Noid, W G

2016-05-28

This work investigates the promise of a "bottom-up" extended ensemble framework for developing coarse-grained (CG) models that provide predictive accuracy and transferability for describing both structural and thermodynamic properties. We employ a force-matching variational principle to determine system-independent, i.e., transferable, interaction potentials that optimally model the interactions in five distinct heptane-toluene mixtures. Similarly, we employ a self-consistent pressure-matching approach to determine a system-specific pressure correction for each mixture. The resulting CG potentials accurately reproduce the site-site rdfs, the volume fluctuations, and the pressure equations of state that are determined by all-atom (AA) models for the five mixtures. Furthermore, we demonstrate that these CG potentials provide similar accuracy for additional heptane-toluene mixtures that were not included their parameterization. Surprisingly, the extended ensemble approach improves not only the transferability but also the accuracy of the calculated potentials. Additionally, we observe that the required pressure corrections strongly correlate with the intermolecular cohesion of the system-specific CG potentials. Moreover, this cohesion correlates with the relative "structure" within the corresponding mapped AA ensemble. Finally, the appendix demonstrates that the self-consistent pressure-matching approach corresponds to minimizing an appropriate relative entropy.

DNS study of the ignition of n-heptane fuel spray under high pressure and lean conditions

NASA Astrophysics Data System (ADS)

Wang, Yunliang; Rutland, Christopher J.

2005-01-01

Direct numerical simulations (DNS) are used to investigate the ignition of n-heptane fuel spray under high pressure and lean conditions. For the solution of the carrier gas fluid, the Eulerian method is employed, while for the fuel spray, the Lagrangian method is used. A chemistry mechanism for n-heptane with 33 species and 64 reactions is adopted to describe the chemical reactions. Initial carrier gas temperature and pressure are 926 K and 30.56 atmospheres, respectively. Initial global equivalence ratio is 0.258. Two cases with droplet radiuses of 35.5 and 20.0 macrons are simulated. Evolutions of the carrier gas temperature and species mass fractions are presented. Contours of the carrier gas temperature and species mass fractions near ignition and after ignition are presented. The results show that the smaller fuel droplet case ignites earlier than the larger droplet case. For the larger droplet case, ignition occurs first at one location; for the smaller droplet case, however, ignition occurs first at multiple locations. At ignition kernels, significant NO is produced when temperature is high enough at the ignition kernels. For the larger droplet case, more NO is produced than the smaller droplet case due to the inhomogeneous distribution and incomplete mixing of fuel vapor.

Vapor phase nucleation of the short-chain n-alkanes (n-pentane, n-hexane and n-heptane): Experiments and Monte Carlo simulations.

PubMed

Ogunronbi, Kehinde E; Sepehri, Aliasghar; Chen, Bin; Wyslouzil, Barbara E

2018-04-14

We measured the nucleation rates of n-pentane through n-heptane in a supersonic nozzle at temperatures ranging from ca. 109 K to 168 K. For n-pentane and n-hexane, these are the first nucleation rate measurements that have been made, and the trends in the current data agree well with those in the earlier work of Ghosh et al. [J. Chem. Phys. 132, 024307 (2010)] for longer chain alkanes. Complementary Monte Carlo simulations, using the transferable potentials for phase equilibria-united atom potentials, suggest that despite the high degree of supercooling, the critical clusters remain liquid like under experimental conditions for n-pentane through n-heptane, but adopt more ordered structures for n-octane and n-nonane. For all three alkanes, the experimental and simulated nucleation rates are offset by ∼3 orders of magnitude when plotted as a function of ln S/(T c /T - 1) 1.5 . Explicitly accounting for the surface tension difference between the real and model substances, or alternatively using the Hale [Phys. Rev. A 33, 4156 (1986); Metall. Mater. Trans. A 23, 1863 (1992)] scaling parameter, Ω, consistent with the model potential, increases the offset to ∼6 orders of magnitude.

Vapor phase nucleation of the short-chain n-alkanes (n-pentane, n-hexane and n-heptane): Experiments and Monte Carlo simulations

NASA Astrophysics Data System (ADS)

Ogunronbi, Kehinde E.; Sepehri, Aliasghar; Chen, Bin; Wyslouzil, Barbara E.

2018-04-01

We measured the nucleation rates of n-pentane through n-heptane in a supersonic nozzle at temperatures ranging from ca. 109 K to 168 K. For n-pentane and n-hexane, these are the first nucleation rate measurements that have been made, and the trends in the current data agree well with those in the earlier work of Ghosh et al. [J. Chem. Phys. 132, 024307 (2010)] for longer chain alkanes. Complementary Monte Carlo simulations, using the transferable potentials for phase equilibria-united atom potentials, suggest that despite the high degree of supercooling, the critical clusters remain liquid like under experimental conditions for n-pentane through n-heptane, but adopt more ordered structures for n-octane and n-nonane. For all three alkanes, the experimental and simulated nucleation rates are offset by ˜3 orders of magnitude when plotted as a function of ln S/(Tc/T - 1)1.5. Explicitly accounting for the surface tension difference between the real and model substances, or alternatively using the Hale [Phys. Rev. A 33, 4156 (1986); Metall. Mater. Trans. A 23, 1863 (1992)] scaling parameter, Ω, consistent with the model potential, increases the offset to ˜6 orders of magnitude.

Binary chromatographic data and estimation of adsorbent porosities. [data for system n-heptane/n-pentane

NASA Technical Reports Server (NTRS)

Meisch, A. J.

1972-01-01

Data for the system n-pentane/n-heptane on porous Chromosorb-102 adsorbent were obtained at 150, 175, and 200 C for mixtures containing zero to 100% n-pentane by weight. Prior results showing limitations on superposition of pure component data to predict multicomponent chromatograms were verified. The thermodynamic parameter MR0 was found to be a linear function of sample composition. A nonporous adsorbent failed to separate the system because of large input sample dispersions. A proposed automated data processing scheme involving magnetic tape recording of the detector signals and processing by a minicomputer was rejected because of resolution limitations of the available a/d converters. Preliminary data on porosity and pore size distributions of the adsorbents were obtained.

Suppression of reaction during rapid compression and its effect on ignition delay

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mohamed, C.

1998-02-01

A single-shot, rapid compression machine has been used to investigate the effect of diethylamine (5 mol%) on the spontaneous ignition (or autoignition) of n-heptane and n-pentane in stoichiometric proportion in air ({psi} = 1.0). Autoignition delays were measured at compressed gas temperatures and pressures in the range 659--950 K and 9--11 atm, respectively. In addition to pressure-time data, the total light output from the chamber was recorded as a function of time using a photomultiplier positioned at the end window. Diethylamine retards the first stage of the two-stage ignition of n-heptane and n-pentane, causing a reduction in both the pressuremore » rise and the light intensity associated with the first (cool flame) stage. A longer duration of the second stage of ignition was measured. Consequently, an increase in ignition delay was observed for n-heptane throughout the temperature range 650--950 K, for which first-stage reactions persist in the compression stroke at temperatures above 850 K. The ignition delay of n-pentane was increased in the range 650--850 K by the addition of diethylamine, but was decreased at compressed gas temperatures greater than 850 K. The possible mechanisms of the inhibition of the first stage of autoignition and promotion of the second stage by diethylamine are outlined.« less

The effect of organic solvent, temperature and mixing time on the production of oil from Moringa oleifera seeds

NASA Astrophysics Data System (ADS)

Ghazali, Q.; Yasin, N. H. M.

2016-06-01

The effect of three different organic solvent, temperature and mixing time on the production of oil from M.oleifera seeds were studied to evaluate the effectiveness in obtaining the high oil yield based on the percentage of oil production. The modified version of Soxhlet extraction method was carried out to extract the oil from M.oleifera seeds by using hexane, heptane and ethanol as the organic solvent. Among the three solvents, it is found that heptane yield higher oil from M.oleifera seeds with maximum oil yield of 36.37% was obtained followed by hexane and ethanol with 33.89% and 18.46%, respectively. By using heptane as a solvent, the temperature (60oC, 70oC, 80oC) and mixing time (6 h, 7 h, and 8 h) were investigated to ensure the high oil yield over the experimental ranges employed and high oil yield was obtained at 600C for 6 h with percentage oil yield of 36.37%. The fatty acid compositions of M.oleifera seeds oil were analyzed using Gas Chromatography/Mass Spectrometry (GC-MS). The main components of fatty acid contained in the oil extracted from M.oleifera seeds was oleic acid, followed by palmitic acid and arachidic acid, and small amount of behenic acid and margaric acid.

Tolman lengths and rigidity constants of multicomponent fluids: Fundamental theory and numerical examples

NASA Astrophysics Data System (ADS)

Aasen, Ailo; Blokhuis, Edgar M.; Wilhelmsen, Øivind

2018-05-01

The curvature dependence of the surface tension can be described by the Tolman length (first-order correction) and the rigidity constants (second-order corrections) through the Helfrich expansion. We present and explain the general theory for this dependence for multicomponent fluids and calculate the Tolman length and rigidity constants for a hexane-heptane mixture by use of square gradient theory. We show that the Tolman length of multicomponent fluids is independent of the choice of dividing surface and present simple formulae that capture the change in the rigidity constants for different choices of dividing surface. For multicomponent fluids, the Tolman length, the rigidity constants, and the accuracy of the Helfrich expansion depend on the choice of path in composition and pressure space along which droplets and bubbles are considered. For the hexane-heptane mixture, we find that the most accurate choice of path is the direction of constant liquid-phase composition. For this path, the Tolman length and rigidity constants are nearly linear in the mole fraction of the liquid phase, and the Helfrich expansion represents the surface tension of hexane-heptane droplets and bubbles within 0.1% down to radii of 3 nm. The presented framework is applicable to a wide range of fluid mixtures and can be used to accurately represent the surface tension of nanoscopic bubbles and droplets.

Volatile Profile of Raw Lamb Meat Stored at 4 ± 1 °C: The Potential of Specific Aldehyde Ratios as Indicators of Lamb Meat Quality

PubMed Central

2018-01-01

The objectives of the present study were: (a) to evaluate the aroma evolution of raw lamb packaged in multi-layer coating film and stored at 4 ± 1 °C, with respect to storage time and (b) to investigate whether specific aldehyde ratios could serve as markers of lamb meat freshness and degree of oxidation. Volatile compounds were determined using headspace solid phase microextraction coupled to gas chromatography/mass spectrometry. Results showed that the most dominant volatiles were 2,2,4,6,6-pentamethyl-heptane, hexanal, 1-octen-3-ol, 1-hexanol, carbon disulfide and p-cymene. Volatile compound content was increased during storage time. However, statistically significant differences were recorded only for hexanal, heptanal, and nonanal (p < 0.05). Additionally, the evolution of aldehydes during storage recorded a positive Pearson’s correlation (r) (p < 0.05), whereas hexanal to nonanal, heptanal to nonanal, octanal to nonanal ratios, along with the sum of aldehydes to nonanal ratio, were positively correlated (r = 0.83–1.00) with the degree of oxidation (mg malonic dialdehyde per kg of lamb meat). A perfect Pearson’s correlation (r = 1) was obtained for the ratio hexanal to nonanal. Therefore, this ratio is proposed as an indicator of lamb meat freshness and overall quality. PMID:29547528

Propellant vaporization as a criterion for rocket-engine design : experimental effect of fuel temperature on liquid-oxygen - heptane performance

NASA Technical Reports Server (NTRS)

Heidmann, M F

1957-01-01

Characteristic exhaust velocity of a 200-pound-thrust rocket engine was evaluated for fuel temperatures of -90 degrees, and 200 degrees f with a spray formed by two impinging heptane jets reacting in a highly atomized oxygen atmosphere. Tests covered a range of mixture ratios and chamber lengths. The characteristic exhaust-velocity efficiency increased 2 percent for a 290 degree f increase in fuel temperature. This increase in performance can be compared with that obtained by increasing chamber length by about 1/2 inch. The result agrees with the fuel-temperature effect predicted from an analysis based on droplet evaporation theory. Mixture ratio markedly affected characteristic exhaust velocity efficiency, but total flow rate and fuel temperature did not.

40 CFR Appendix A to Part 439 - Tables

Code of Federal Regulations, 2014 CFR

2014-07-01

... Isobutyraldehyde 1 Aldehydes. n-Heptane 1 Alkanes. n-Hexane 1 Diethylamine 1 Amines. Triethylamine Benzene... Methyl formate Tetrahydrofuran 1 Ethers. Isopropyl ether Acetone 1 Ketones. 4-Methyl-2-pentanone (MIBK...

40 CFR Appendix A to Part 439 - Tables

Code of Federal Regulations, 2012 CFR

2012-07-01

... Isobutyraldehyde 1 Aldehydes. n-Heptane 1 Alkanes. n-Hexane 1 Diethylamine 1 Amines. Triethylamine Benzene... Methyl formate Tetrahydrofuran 1 Ethers. Isopropyl ether Acetone 1 Ketones. 4-Methyl-2-pentanone (MIBK...

40 CFR Appendix A to Part 439 - Tables

Code of Federal Regulations, 2013 CFR

2013-07-01

... Isobutyraldehyde 1 Aldehydes. n-Heptane 1 Alkanes. n-Hexane 1 Diethylamine 1 Amines. Triethylamine Benzene... Methyl formate Tetrahydrofuran 1 Ethers. Isopropyl ether Acetone 1 Ketones. 4-Methyl-2-pentanone (MIBK...

21 CFR 177.1655 - Polysulfone resins.

Code of Federal Regulations, 2010 CFR

2010-04-01

...)(2) of this section. (c) Polysulfone resins, when extracted at reflux temperatures for 6 hours with... acetic acid in distilled water, and n-heptane, yield total extractives in each extracting solvent not to...

21 CFR 177.1655 - Polysulfone resins.

Code of Federal Regulations, 2012 CFR

2012-04-01

...)(2) of this section. (c) Polysulfone resins, when extracted at reflux temperatures for 6 hours with... acetic acid in distilled water, and n-heptane, yield total extractives in each extracting solvent not to...

21 CFR 177.1655 - Polysulfone resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... extracted at reflux temperatures for 6 hours with the solvents—distilled water, 50 percent (by volume) ethyl alcohol in distilled water, 3 percent acetic acid in distilled water, and n-heptane, yield total...

21 CFR 177.1655 - Polysulfone resins.

Code of Federal Regulations, 2013 CFR

2013-04-01

...)(2) of this section. (c) Polysulfone resins, when extracted at reflux temperatures for 6 hours with... acetic acid in distilled water, and n-heptane, yield total extractives in each extracting solvent not to...

40 CFR Appendix A to Part 439 - Tables

Code of Federal Regulations, 2010 CFR

2010-07-01

... Aldehydes. n-Heptane 1 Alkanes. n-Hexane 1 Diethylamine 1 Amines. Triethylamine Benzene Aromatics. Toluene 1... Tetrahydrofuran 1 Ethers. Isopropyl ether Acetone 1 Ketones. 4-Methyl-2-pentanone (MIBK) Ammonia (aqueous...

40 CFR Appendix A to Part 439 - Tables

Code of Federal Regulations, 2011 CFR

2011-07-01

... Aldehydes. n-Heptane 1 Alkanes. n-Hexane 1 Diethylamine 1 Amines. Triethylamine Benzene Aromatics. Toluene 1... Tetrahydrofuran 1 Ethers. Isopropyl ether Acetone 1 Ketones. 4-Methyl-2-pentanone (MIBK) Ammonia (aqueous...

NOx formation from the combustion of monodisperse n-heptane sprays doped with fuel-nitrogen additives

NASA Technical Reports Server (NTRS)

Sarv, Hamid; Cernansky, Nicholas P.

1989-01-01

A series of experiments with simulated synthetic fuels were conducted in order to investigate the effect of droplet size on the conversion of fuel-nitrogen to NOx. Pyridine and pyrrole were added to n-heptane as nitrogen-containing additives and burned as monodisperse fuel droplets under various operating conditions in a spray combustion facility. The experimental results indicate that under stoichiometric and fuel-rich conditions, reducing the droplet size increases the efficiency of fuel-N conversion to NOx. This observation is associated with improved oxidation of the pyrolysis fragments of the additive by better oxygen penetration through the droplet flame zone. The dominant reactions by which fuel-N is transformed to NOx were also considered analytically by a premixed laminar flame code. The calculations are compared to the small droplet size results.

Tuning aggregation of microemulsion droplets and silica nanoparticles using solvent mixtures.

PubMed

Salabat, Alireza; Eastoe, Julian; Mutch, Kevin J; Tabor, Rico F

2008-02-15

The effect of solvent on stability of water-in-oil microemulsions has been studied with AOT (sodium bis(2-ethylhexyl)sulfosuccinate) and different solvent mixtures of n-heptane, toluene and dodecane. Dynamic light scattering DLS was used to monitor the apparent diffusion coefficient D(A) and effective microemulsion droplet diameter on changing composition of the solvent. Interdroplet attractive interactions, as indicated by variations in D(A), can be tuned by formulation of appropriate solvent mixtures using heptane, toluene, and dodecane. In extreme cases, solvent mixtures can be used to induce phase transitions in the microemulsions. Aggregation and stability of model AOT-stabilized silica nanoparticles in different solvents were also investigated to explore further these solvent effects. For both systems the state of aggregation can be correlated with the effective molecular volume of the solvent V(mol)(eff) mixture.

Purification of antibiotics from the biocontrol agent Streptomyces anulatus S37 by centrifugal partition chromatography.

PubMed

Couillerot, Olivier; Loqman, Souad; Toribio, Alix; Hubert, Jane; Gandner, Léa; Nuzillard, Jean-Marc; Ouhdouch, Yedir; Clément, Christophe; Barka, Essaid Ait; Renault, Jean-Hugues

2014-01-01

A novel actinomycete strain, Streptomyces anulatus S37, has been isolated from the rhizosphere of healthy Moroccan Vitis vinifera on the basis on its ability to promote grapevine growth and to induce natural defences against various phytopathogens. In the present work, the main bioactive metabolites produced by S. anulatus S37 were isolated. A crude n-BuOH extract of the S37 fermentation broth was firstly partitioned in a biphasic solvent system composed of n-heptane, methanol, and water (5:1.5:3.5, v/v). The most active organic fraction (1.1g) as revealed by TLC-bioautography was subsequently separated by a two-step centrifugal partition chromatography procedure. The first separation was performed in the ascending mode at 6mL/min with the biphasic solvent system n-heptane, ethyl acetate, methanol and water (2:1:2:1, v/v), to finally recover 40mg of a pure compound identified as streptochlorin by NMR spectroscopy. In a second separation, the solvent system n-heptane, acetonitrile, and water (5:5:4, v/v) was used in the ascending mode at 3mL/min to purify 135mg of nigericin and 53mg of piericidin A1. Assays performed with the three compounds have confirmed their inhibitory impact on the growth of Botryris cinerea in dual confrontation and also on V. vinifera L. plantlets. Copyright © 2013 Elsevier B.V. All rights reserved.

Structural and phase transformations during ball milling of titanium in medium of liquid hydrocarbons

NASA Astrophysics Data System (ADS)

Dorofeev, G. A.; Lubnin, A. N.; Lad'yanov, V. I.; Mukhgalin, V. V.; Puskkarev, B. E.

2014-02-01

It has been shown using X-ray diffraction, scanning electron microscopy, and chemical analysis that, upon ball milling of α-titanium in liquid organic media (toluene and n-heptane), a nanocrystalline fcc phase is formed that is a metastable carbohydride Ti(C,H) deficient in hydrogen and carbon compared to stable carbohydrides. The dimensions of powder particles after milling in toluene and n-heptane differ substantially (are 5-10 and 20-30 μm, respectively. It has been shown that the kinetics of the formation of Ti(C,H) is independent of the milling medium. The atomic ratios H/C in the products of mechanosynthesis agree well with those corresponding to the employed organic media, i.e., H/C = 1.1 for toluene and 2.3 for n-heptane. A solid-liquid mechanism of mechanosynthesis is suggested, which includes repeated processes of particle fracturing with the formation of fresh surfaces, adsorption of liquid hydrocarbons on these surfaces, and subsequent cold welding of the newly formed particles. It is assumed that the formation of the fcc phase in the process of milling is connected with the generation of stacking faults in α-Ti. Upon annealing at 550°C, the fcc phase decomposes with the formation of stable titanium carbide TiC (annealing in a vacuum) or stable titanium carbohydride and a β-Ti(H) solid solution (annealing in argon) with a partial reverse transformation Ti(C,H) → α-Ti in both cases.

Combustion Instability in an Acid-Heptane Rocket with a Pressurized-Gas Propellant Pumping System

NASA Technical Reports Server (NTRS)

Tischler, Adelbert O.; Bellman, Donald R.

1951-01-01

Results of experimental measurements of low-frequency combustion instability of a 300-pound thrust acid-heptane rocket engine were compared to the trends predicted by an analysis of combustion instability in a rocket engine with a pressurized-gas propellant pumping system. The simplified analysis, which assumes a monopropellant model, was based on the concept of a combustion the delay occurring from the moment of propellant injection to the moment of propellant combustion. This combustion time delay was experimentally measured; the experimental values were of approximately half the magnitude predicted by the analysis. The pressure-fluctuation frequency for a rocket engine with a characteristic length of 100 inches and operated at a combustion-chamber pressure of 280 pounds per square inch absolute was 38 cycles per second; the analysis indicated. a frequency of 37 cycles per second. Increasing combustion-chamber characteristic length decreased the pressure-fluctuation frequency, in conformity to the analysis. Increasing the chamber operating pressure or increasing the injector pressure drop increased the frequency. These latter two effects are contrary to the analysis; the discrepancies are attributed to the conflict between the assumptions made to simplify the analysis and the experimental conditions. Oxidant-fuel ratio had no apparent effect on the experimentally measured pressure-fluctuation frequency for acid-heptane ratios from 3.0 to 7.0. The frequencies decreased with increased amplitude of the combustion-chamber pressure variations. The analysis indicated that if the combustion time delay were sufficiently short, low-frequency combustion instability would be eliminated.

New carbocyclic N(6)-substituted adenine and pyrimidine nucleoside analogues with a bicyclo[2.2.1]heptane fragment as sugar moiety; synthesis, antiviral, anticancer activity and X-ray crystallography.

PubMed

Tănase, Constantin I; Drăghici, Constantin; Cojocaru, Ana; Galochkina, Anastasia V; Orshanskaya, Jana R; Zarubaev, Vladimir V; Shova, Sergiu; Enache, Cristian; Maganu, Maria

2015-10-01

New nucleoside analogues with an optically active bicyclo[2.2.1]heptane skeleton as sugar moiety and 6-substituted adenine were synthesized by alkylation of 6-chloropurine intermediate. Thymine and uracil analogs were synthesized by building the pyrimidine ring on amine 1. X-ray crystallography confirmed an exo-coupling of the thymine to the ring and an L configuration of the nucleoside analogue. The library of compounds was tested for their inhibitory activity against influenza virus A∖California/07/09 (H1N1)pdm09 and coxsackievirus B4 in cell culture. Compounds 13a and 13d are the most promising for their antiviral activity against influenza, and compound 3c against coxsackievirus B4. Compounds 3b and 3g were tested for anticancer activity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effect of design changes and operating conditions on combustion and operational performance of a 28-inch diameter Ram-jet engine / T. B. Shillito and Shigeo Nakanishi

NASA Technical Reports Server (NTRS)

Shillito, T B; Nakanishi, Shigeo

1952-01-01

The results of an altitude test-chamber investigation of the effects of a number of design changes and operating conditions on altitude peformance of a 28-inch diameter ram jet engine are presented. Most of the investigation was for a simulated flight Mach number of 2.0 above the tropopause. Fuel-air distribution, gutter width, the presence of a pilot flame, cimbustion-chamber-inlet temperature, and exhaust-nozzle throat area were found to have significant effects on limits of combustion. Combustion efficiency increased with increasing combustion-chamber-inlet temperature and was adversely affected by an increase in the exhaust-nozzld area. Similiar lean limits of combustion were obtained for both Diesel fuel and normal heptane, but combustion efficiences obtained with Diesel fuel were lower than those obtained with normal heptane.

Effect of SiO2/Al2O3 Ratio on Micro-Mesopore Formation for Pt/Beta-MCM-41 via NaOH Treatment and the Catalytic Performance in N-heptane Hydro isomerization

NASA Astrophysics Data System (ADS)

Gao, Li; Shi, Zhiyuan; Liu, Yingming; Zhao, Yuanshou; Liu, Qinghua; Xu, Chengguo; Bai, Peng; Yan, Zifeng

2018-01-01

Micro-mesoporous composite material Beta-MCM-41(BM) were hydrothermally synthesized by treating parent beta with molar SiO2/Al2O3 ratios of 12.5, 20 and 30 as precursors. The influence of SiO2/Al2O3 ratio of zeolite beta on effective micro-mesoporous composite formation was studied by investigating the crystallinity, morphology, chemical composition, acidity and textural property of Beta-MCM-41 through XRD, nitrogen adsorption, SEM, TEM, NH3-TPD, FTIR and Pyridine-FTIR. The catalytic performance was evaluated in terms of n-heptane hydro isomerization. The results demonstrated that Beta-MCM-41 supported Pt catalysts showed higher selectivity to isoheptanes than Pt/Beta. It was attributed to the superiorities of the pore structure and mesoporous accelerated the diffusion of larger molecules of isoheptanes.

Droplet Combustion in a Slow Convective Flow

NASA Technical Reports Server (NTRS)

Nayagam, V.; Hicks, M. C.; Kaib, N.; Ackerman, M.; Haggard, J. B., Jr.; Williams, F. A.

2001-01-01

The objective of the present flight experiment definition study is to investigate the effects of slow forced convective flows on the dynamics of isolated single droplet combustion and is designed to complement the quiescent, microgravity droplet combustion experiments (DCE-1 and DCE-2) of Williams and Dryer. The fuels selected for this study are the same as those of DCE, namely, a sooting alkane fuel (heptane) and a non-sooting alcohol (methanol), and imposed flow rates are chosen between 0 and 20 cm/s with varying ambient oxygen concentrations and pressures. Within this velocity range, both accelerating and decelerating flow effects will also be investigated. Two different approaches to generate the forced flow are currently under development in ground-based facilities; the first is a flow tunnel concept where the forced flow is imposed against a stationary droplet, and in the second a tethered droplet is translated at a specified velocity in a quiescent ambient medium. Depending upon the engineering feasibility a selection will be made between these two approaches so that the experiment can be accommodated in the Multiple Droplet Combustion Apparatus (MDCA) currently being designed for the International Space Station. Recently, we have finished designing and fabricating the experimental rigs using both the above mentioned concepts. The flow tunnel concept is implemented in a 2.2 second drop tower rig. Preliminary experiments have been carried out using heptane and methanol in air at atmospheric pressure. The translating droplet apparatus is scheduled to be tested in the 5 second drop facility in the near future. This report presents some of the experimental results obtained for heptane.

Theoretical study of binding and permeation of ether-based polymers through interfaces.

PubMed

Samanta, Susruta; Hezaveh, Samira; Roccatano, Danilo

2013-11-27

We present a molecular dynamics simulation study on the interactions of poly(ethylene oxide) (PEO), poly(propylene oxide) (PPO), and their ABA-type block copolymer, poloxamers, at water/n-heptane and 1,2-dimyristoyl-sn-glycero-3-phospatidycholine (DMPC) lipid bilayer/water interfaces. The partition coefficients in water/1-octanol of the linear polyethers up to three monomers were calculated. The partition coefficients evidenced a higher hydrophobicity of the PPO in comparison to PEO. At the water/n-heptane interface, the polymers tend to adopt elongated conformations in agreement with similar experimental ellipsometry studies of different poloxamers. In the case of the poloxamers at the n-heptane/water interface, the stronger preference of the PPO block for the hydrophobic phase resulted in bottle-brush-type polymer conformations. At lipid bilayer/water interface, the PEO polymers, as expected from their hydrophilic nature, are weakly adsorbed on the surface of the lipid bilayer and locate in the water phase close to the headgroups. The free energy barriers of permeation calculated for short polymer chains suggest a thermodynamics propensity for the water phase that increase with the chain length. The lower affinity of PEO for the hydrophobic interior of the lipid bilayer resulted in the spontaneous expulsion within the simulation time. On the contrary, PPO chains and poloxamers have a longer residence time inside the bilayer, and they tend to concentrate in the tail region of the bilayer near the polar headgroups. In addition, polymers with PPO unit length comparable to the thickness of the hydrophobic region of the bilayer tend to span across the bilayer.

Synthesis of 7-azabicyclo[2.2.1]heptane and 2-oxa-4-azabicyclo[3.3.1]non-3-ene derivatives by base-promoted heterocyclization of alkyl N-(cis(trans)-3,trans(cis)-4-dibromocyclohex-1-yl)carbamates and N-(cis(trans)-3,trans(cis)-4-dibromocyclohex-1-yl)-2,2,2-trifluoroacetamides.

PubMed

Gómez-Sanchez, Elena; Soriano, Elena; Marco-Contelles, José

2007-11-09

We have studied the base-promoted heterocyclization of alkyl N-(cis(trans)-3,trans(cis)-4-dibromocyclohex-1-yl)carbamates and N-(cis(trans)-3,trans(cis)-4-dibromocyclohex-1-yl)-2,2,2-trifluoroacetamides, investigating the effect of the nitrogen protecting group and the relative configuration of the leaving group at C3 and C4 on the outcome of this reaction. We have observed that the sodium hydride-promoted heterocyclization of alkyl N-(cis-3,trans-4-dibromocyclohex-1-yl)carbamates (10, 12, 14, 16, 18) is a convenient method for the synthesis of 7-azabicyclo[2.2.1]heptane derivatives. For instance, the reaction of tert-butyl N-(cis-3,trans-4-dibromocyclohex-1-yl)carbamate (10) with sodium hydride in DMF at room temperature provides 2-bromo-7-[(tert-butoxy)carbonyl]-7-azabicyclo[2.2.1]heptane (2) (52% yield), whose t-BuOK-promoted hydrogen bromide elimination affords 7-[(tert-butoxy)carbonyl]-7-azabicyclo[2.2.1]hept-2-ene (31) in 78% yield, an intermediate in the total synthesis of epibatidine (1). However, the NaH/DMF-mediated heterocyclization of alkyl N-(trans-3,cis-4-dibromocyclohex-1-yl)carbamates (11, 13) is a more structure dependent reaction, where the nucleophilic attack of the oxygen atom of the protecting group controls the outcome of the reaction, giving rise to benzooxazolone and 2-oxa-4-azabicyclo[3.3.1]non-3-ene derivatives, respectively, from low to moderate yields, in complex reaction mixtures. Conversely, the NaH/DMF heterocyclizations of N-(cis-3,trans-4-dibromocyclohex-1-yl)-2,2,2-trifluoroacetamide (40) or N-(trans-3,cis-4-dibromocyclohex-1-yl)-2,2,2-trifluoroacetamide (42) are very clean reactions giving 7-azabicyclo[2.2.1]heptane or 2-oxa-4-azabicyclo[3.3.1]non-3-ene derivatives, respectively, in good yields. Finally, a mechanistic investigation, based on DFT calculations, has been carried out to rationalize the formation of the different adducts.

21 CFR 177.1040 - Acrylonitrile/styrene copoly-mer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... a size that will pass through a U.S. Standard Sieve No. 6 and that will be held on a U.S. Standard Sieve No. 10 is extracted with 250 mil of deionized water or reagent grade n-heptane at reflux...

21 CFR 177.1040 - Acrylonitrile/styrene copoly-mer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... a size that will pass through a U.S. Standard Sieve No. 6 and that will be held on a U.S. Standard Sieve No. 10 is extracted with 250 mil of deionized water or reagent grade n-heptane at reflux...

21 CFR 177.1040 - Acrylonitrile/styrene copoly-mer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... a size that will pass through a U.S. Standard Sieve No. 6 and that will be held on a U.S. Standard Sieve No. 10 is extracted with 250 mil of deionized water or reagent grade n-heptane at reflux...

Analysis of non-phthalates plasticizers on porous graphitic carbon by supercritical fluid chromatography using evaporative light scattering detection.

PubMed

Vaccher, Claude; Decaudin, Bertrand; Sautou, Valérie; Lecoeur, Marie

2014-09-12

The analysis of several plasticizers, widely used in the production of medical devices, was investigated on porous graphitic carbon (PGC) stationary phase in supercritical fluid chromatography (SFC) with an evaporative light scattering detector (ELSD). Due to strong interaction of compounds with the PGC support, solvents of strong eluotropic strength were added to the CO2 supercritical fluid. The effect of alkyl chain (pentane, hexane, heptane) and chlorinated (CH2Cl2, CHCl3, CCl4) solvents was studied on the retention and on the ELSD detection of plasticizers. A co-solvent mixture composed of CHCl3/heptane, eluted under gradient mode, allowed a significant improvement of the ELSD response compared to the use of each solvent individually. Then, a central composite design (CCD) was implemented to optimize both the separation and the detection of plasticizers. The parameters involved were the outlet pressure, the gradient slope, the co-solvent composition and the drift tube temperature of the ELSD. After optimization, baseline separation of plasticizers was achieved in 7min and best signal-to-noise ratios were obtained with outlet pressure and drift tube temperature of ELSD set at 200bar and 31°C, respectively. The co-solvent mixture was also composed of CHCl3/heptane (35/65 v/v) and a gradient from 15 to 60% of co-solvent in 2.2min was employed. The results demonstrated that CCD is a powerful tool for the optimization of SFC/ELSD method and the response surface model analysis can provide statistical understandings of the significant factors required to achieve optimal separation and ELSD sensitivity. Copyright © 2014 Elsevier B.V. All rights reserved.

Recent Advances In Science Support For Isolated Droplet Combustion Experiments

NASA Technical Reports Server (NTRS)

Dryer, F. L.; Kazakov, A.; Urban, B. D.; Kroenlein, K.

2003-01-01

In a joint program involving Prof. F.A. Williams of the University of California, San Diego and Dr. V. Nayagam of the National Center for Microgravity Research, the combustion characteristics of isolated liquid fuel droplets of n-heptane, n-decane, methanol, methanol-water, ethanol and ethanol-water having initial diameters between about 1 mm and 6 mm continues to be investigated. The objectives of the work are to improve fundamental knowledge of droplet combustion dynamics for pure fuels and fuel-water mixtures through microgravity experiments and theoretical analyses. The Princeton contributions support the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies through experiments and numerical modeling. UCSD contributions are described in a companion communication in this conference. The Princeton effort also addresses the analyses of Fiber Supported Droplet Combustion (FSDC) experiments conducted with the above fuels and collaborative work with others who are investigating droplet combustion in the presence of steady convection. A thorough interpretation of droplet burning behavior for n-heptane and n-decane over a relatively wide range of conditions also involves the influences of sooting on the combustion behavior, and this particular aspect on isolated burning of droplets is under consideration in a collaborative program underway with Drexel University. This collaboration is addressed in another communication at this conference. The one-dimensional, time-dependent, numerical modeling approach that we have continued to evolve for analyzing isolated, quiescent droplet combustion data has been further applied to investigate several facets of isolated droplet burning of simple alcohols, n-heptane, and n-decane. Some of the new results are described below.

A comprehensive detailed chemical kinetic reaction mechanism for combustion of n-alkane hydrocarbons from n-octane to n-hexadecane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westbrook, Charles K.; Pitz, William J.; Herbinet, Olivier

2009-01-15

Detailed chemical kinetic reaction mechanisms have been developed to describe the pyrolysis and oxidation of nine n-alkanes larger than n-heptane, including n-octane (n-C{sub 8}H{sub 18}), n-nonane (n-C{sub 9}H{sub 20}), n-decane (n-C{sub 10}H{sub 22}), n-undecane (n-C{sub 11}H{sub 24}), n-dodecane (n-C{sub 12}H{sub 26}), n-tridecane (n-C{sub 13}H{sub 28}), n-tetradecane (n-C{sub 14}H{sub 30}), n-pentadecane (n-C{sub 15}H{sub 32}), and n-hexadecane (n-C{sub 16}H{sub 34}). These mechanisms include both high temperature and low temperature reaction pathways. The mechanisms are based on previous mechanisms for the primary reference fuels n-heptane and iso-octane, using the reaction classes first developed for n-heptane. Individual reaction class rules are as simple asmore » possible in order to focus on the parallelism between all of the n-alkane fuels included in the mechanisms. These mechanisms are validated through extensive comparisons between computed and experimental data from a wide variety of different sources. In addition, numerical experiments are carried out to examine features of n-alkane combustion in which the detailed mechanisms can be used to compare reactivities of different n-alkane fuels. The mechanisms for these n-alkanes are presented as a single detailed mechanism, which can be edited to produce efficient mechanisms for any of the n-alkanes included, and the entire mechanism, with supporting thermochemical and transport data, together with an explanatory glossary explaining notations and structural details, is available for download from our web page. (author)« less

Study on Desorption Process of n-Heptane and Methyl Cyclohexane Using UiO-66 with Hierarchical Pores.

PubMed

Chen, Sijia; Zhang, Lin; Zhang, Zhao; Qian, Gang; Liu, Zongjian; Cui, Qun; Wang, Haiyan

2018-06-06

UiO-66 (UiO for University of Oslo), is a zirconium-based MOF with reverse shape selectivity, gives an alternative way to produce high purity n-heptane used for the manufacture of high-purity pharmaceuticals. Couple of studies have shown that UiO-66 gives a high selectivity on the separation of n-/iso-alkanes. However, the microporous structure of UiO-66 causes poor mass transport during the desorption process. In this work, hierarchical-pore UiO-66 (H-UiO-66) was synthesized and utilized as an adsorbent of n-heptane (nHEP) and methyl cyclohexane (MCH) for systematically studying the desorption process of n/iso-alkanes. A suite of physical methods, including XRD patterns verified the UiO-66 structures and HRTEM showed the existence of hierarchical pores. N2 adsorption-desorption isotherms further confirmed the size distribution of hierarchical pores in H-UiO-66. Of particular note, the MCH/nHEP selectivity of H-UiO-66 is similar with UiO-66 in the same adsorption conditions, the desorption process of nHEP/MCH from H-UiO-66 is dramatically enhanced, viz, the desorption rates for nHEP/MCH from H-UiO-66 is enhanced by 30%/23% as comparing to UiO-66 at most. Moreover, desorption activation energy (Ed) derived from temperature-programmed desorption (TPD) experiments indicate that the Ed for nHEP/MCH is lower on H-UiO-66, i.e., the Ed of MCH on H-UiO-66 is ~37% lower than that on UiO-66 at most, leading to a milder condition for the desorption process. The introduction of hierarchical structures will be applicable for the optimization of desorption process during separation on porous materials.

The Effect of Food-Simulating Agents on the Bond Strength of Hard Chairside Reline Materials to Denture Base Resin.

PubMed

Fatemi, Farzaneh Sadat; Vojdani, Mahroo; Khaledi, Amir Ali Reza

2018-06-08

To investigate the influence of food-simulating agents on the shear bond strength between direct hard liners and denture base acrylic resin. In addition, mode of failure was evaluated. One hundred fifty cylindrical columns of denture base resin were fabricated and bonded to three types of hard reline materials (Hard GC Reline, Tokuyama Rebase II Fast, TDV Cold Liner Rebase). Specimens of each reline material were divided into five groups (n = 10) to undergo 12-day immersion in distilled water, 0.02 N citric acid aqueous solution, heptane, and 40% ethanol/water solution at 37°C. The control group was not immersed in any solution. The shear bond strength test was performed, and the failure mode was determined. Statistics were analyzed with two-way ANOVA and chi-square test (α = 0.05). Significant interaction was found between the hard liners and food simulating agents (p < 0.001). The shear bond strength of Tokuyama in 40% ethanol and TDV in heptane decreased significantly (p = 0.001, p < 0.001 respectively); however, none of the solutions could significantly affect the shear bond strength of Hard GC Reline (p = 0.208). The mixed failure mode occurred more frequently in Hard GC Reline compared with the other liners (p < 0.001) and was predominant in specimens with higher bond strength values (p = 0.012). Food simulating agents did not adversely affect the shear bond strength of Hard GC Reline; however, ethanol and heptane decreased the bond strength of Tokuyama and TDV, respectively. These findings may provide support to dentists to recommend restricted consumption of some foods and beverages for patients who have to use dentures relined with certain hard liners. © 2018 by the American College of Prosthodontists.

Molecular dynamics simulation study of solvent effects on conformation and dynamics of polyethylene oxide and polypropylene oxide chains in water and in common organic solvents.

PubMed

Hezaveh, Samira; Samanta, Susruta; Milano, Giuseppe; Roccatano, Danilo

2012-03-28

In this paper, the conformation and dynamics properties of polyethylene oxide (PEO) and polypropylene oxide (PPO) polymer chains at 298 K have been studied in the melt and at infinite dilution condition in water, methanol, chloroform, carbon tetrachloride, and n-heptane using molecular dynamics simulations. The calculated density of PEO melt with chain lengths of n = 2, 3, 4, 5 and, for PPO, n = 7 are in good agreement with the available experimental data. The conformational properties of PEO and PPO show an increasing gauche preference for the O-C-C-O dihedral in the following order water>methanol>chloroform>carbon tetrachloride = n-heptane. On the contrary, the preference for trans conformation has a maximum in carbon tetrachloride and n-heptane followed in the order by chloroform, methanol, and water. The PEO conformational preferences are in qualitative agreement with results of NMR studies. PEO chains formed different types of hydrogen bonds with polar solvent molecules. In particular, the occurrence of bifurcated hydrogen bonding in chloroform was also observed. Radii of gyration of PEO chains of length larger than n = 9 monomers showed a good agreement with light scattering data in water and in methanol. For the shorter chains the observed deviations are probably due to the enhanced hydrophobic effects caused by the terminal methyl groups. For PEO the fitting of end-to-end distance distributions with the semi-flexible chain model at 298 K provided persistence lengths of 0.375 and 0.387 nm in water and methanol, respectively. Finally, the radius of gyration of Pluronic P85 turned out to be 2.25 ± 0.4 nm at 293 K in water in agreement with experimental data.

Molecular dynamics simulation study of solvent effects on conformation and dynamics of polyethylene oxide and polypropylene oxide chains in water and in common organic solvents

NASA Astrophysics Data System (ADS)

Hezaveh, Samira; Samanta, Susruta; Milano, Giuseppe; Roccatano, Danilo

2012-03-01

In this paper, the conformation and dynamics properties of polyethylene oxide (PEO) and polypropylene oxide (PPO) polymer chains at 298 K have been studied in the melt and at infinite dilution condition in water, methanol, chloroform, carbon tetrachloride, and n-heptane using molecular dynamics simulations. The calculated density of PEO melt with chain lengths of n = 2, 3, 4, 5 and, for PPO, n = 7 are in good agreement with the available experimental data. The conformational properties of PEO and PPO show an increasing gauche preference for the O-C-C-O dihedral in the following order water>methanol>chloroform>carbon tetrachloride = n-heptane. On the contrary, the preference for trans conformation has a maximum in carbon tetrachloride and n-heptane followed in the order by chloroform, methanol, and water. The PEO conformational preferences are in qualitative agreement with results of NMR studies. PEO chains formed different types of hydrogen bonds with polar solvent molecules. In particular, the occurrence of bifurcated hydrogen bonding in chloroform was also observed. Radii of gyration of PEO chains of length larger than n = 9 monomers showed a good agreement with light scattering data in water and in methanol. For the shorter chains the observed deviations are probably due to the enhanced hydrophobic effects caused by the terminal methyl groups. For PEO the fitting of end-to-end distance distributions with the semi-flexible chain model at 298 K provided persistence lengths of 0.375 and 0.387 nm in water and methanol, respectively. Finally, the radius of gyration of Pluronic P85 turned out to be 2.25 ± 0.4 nm at 293 K in water in agreement with experimental data.

1,4-hydroxycarbonyl products of the OH radical initiated reactions of C5-C8 n-alkanes in the presence of NO.

PubMed

Reisen, Fabienne; Aschmann, Sara M; Atkinson, Roger; Arey, Janet

2005-06-15

Alkanes account for approximately 50% of nonmethane organic compounds present in urban atmospheres. Previous studies have shown that hydroxycarbonyls are important products ofthe OH radical initiated reactions of > or = C5 n-alkanes, but isomer-specific identifications and quantifications of these products have not been carried out. In this work, we have used solid-phase microextraction fibers precoated with O-(2,3,4,5,6-pentafluorobenzyl)hydroxylamine for on-fiber derivatization of carbonyl-containing compounds with subsequent analyses by combined gas chromatography-mass spectrometry (GC-MS) and GC with flame ionization detection (GC-FID). GC-MS analyses showed the presence of the oximes of 5-hydroxy-2-pentanone and 4-hydroxypentanal from the n-pentane reaction; 5-hydroxy-2-hexanone, 6-hydroxy-3-hexanone, and 4-hydroxyhexanal from the n-hexane reaction; 5-hydroxy-2-heptanone, 6-hydroxy-3-heptanone, 1-hydroxy-4-heptanone, and 4-hydroxyheptanal from the n-heptane reaction; and 5-hydroxy-2-octanone, 6-hydroxy-3-octanone, 7-hydroxy-4-octanone, and 4-hydroxyoctanal from the n-octane reaction. The formation yields of these 1,4-hydroxycarbonyls were determined from GC-FID analyses. By use of the yields of 1,4-hydroxycarbonyls formed from n-hexane, n-heptane, and n-octane at 50% relative humidity (and those from n-pentane at both 5 and 50% relative humidity), then formation of 1,4-hydroxycarbonyls accounts for 54% of the reaction products from n-pentane, 57% from n-hexane, 51% from n-heptane, and 53% from n-octane. Combined with previously measured yields of carbonyls, alkyl nitrates, and hydroxyalkyl nitrates, we can now accountfor approximately 74-118% of the products formed from the n-pentane through n-octane reactions.

Provisional Peer-Reviewed Toxicity Values for N-Heptane

EPA Science Inventory

Provisional Peer-Reviewed Toxicity Values (PPRTV) assessments are developed for use by the Agency’s Office of Land and Emergency Management (OLEM) to support informed decisions in the Superfund program and at hazardous waste sites when a values is not available in the Integrated ...

Provisional Peer-Reviewed Toxicity Values for n-Heptanal

EPA Science Inventory

Provisional Peer-Reviewed Toxicity Values (PPRTV) assessments are developed for use by the Agency’s Office of Land and Emergency Management (OLEM) to support informed decisions in the Superfund program and at hazardous waste sites when a values is not available in the Integrated ...

Binding of carbonyl flavours to canola, pea and wheat proteins using GC/MS approach.

PubMed

Wang, Kun; Arntfield, Susan D

2014-08-15

Interactions of homologous aldehydes (hexanal, heptanal, and octanal) and ketones (2-hexanone, 2-heptanone, and 2-octanone) to salt and alkaline-extracted canola and pea proteins and commercial wheat gluten were studied using GC/MS. Long-chain aldehyde flavours exhibited higher binding affinity, regardless of protein type and isolation method. Salt-extracted canola protein isolates (CPIs) revealed the highest binding capacity to all aldehydes followed by wheat gluten and salt-extracted pea protein isolates (PPIs), while binding of ketone flavours decreased in the order: PPIs>wheat gluten>CPIs. Two aldolisation products, 2-butyl-2-octenal and 2-pentyl-2-nonenal, were detected from the interactions between CPIs with hexanal and heptanal, respectively. Protein thermal behaviour in the presence of these compounds was analysed by differential scanning calorimeter, where decreased ΔH inferred potential conformational changes due to partial denaturation of PPIs. Compared to ketones, aldehyde flavours possessed much higher "unfolding capacity" (lower ΔH), which accounted for their higher binding affinities. Copyright © 2014 Elsevier Ltd. All rights reserved.

[Migrants from disposable gloves and residual acrylonitrile].

PubMed

Wakui, C; Kawamura, Y; Maitani, T

2001-10-01

Disposable gloves made from polyvinyl chloride with and without di(2-ethylhexyl) phthalate (PVC-DEHP, PVC-NP), polyethylene (PE), natural rubber (NR) and nitrile-butadiene rubber (NBR) were investigated with respect to evaporation residue, migrated metals, migrants and residual acrylonitrile. The evaporation residue found in n-heptane was 870-1,300 ppm from PVC-DEHP and PVC-NP, which was due to the plasticizers. Most of the PE gloves had low evaporation residue levels and migrants, except for the glove designated as antibacterial, which released copper and zinc into 4% acetic acid. For the NR and NBR gloves, the evaporation residue found in 4% acetic acid was 29-180 ppm. They also released over 10 ppm of calcium and 6 ppm of zinc into 4% acetic acid, and 1.68-8.37 ppm of zinc di-ethyldithiocarbamate and zinc di-n-butyldithiocarbamate used as vulcanization accelerators into n-heptane. The acrylonitrile content was 0.40-0.94 ppm in NBR gloves.

The joint time-frequency spectrogram structure of heptanes boilover noise

NASA Astrophysics Data System (ADS)

Xu, Qiang

2006-04-01

An experiment was conducted to study the noise characteristics in the boilover phenomena. The boilover occurs in the combustion of a liquid fuel floating on water. It will cause a sharp increase in burning rate and external radiation. Explosive burning of the fuel would cause potential safety consequence. Combustion noise accompanies the development of fire and displays different characteristics in typical period. These characteristics can be used to predict the start time of boilover. The acoustic signal in boilover procedure during the combustion of heptanes-water mixture is obtained in a set of experiments. Joint time-frequency analysis (JTFA) method is applied in the treatment of noise data. Several JTFA algorithms were used in the evaluation. These algorithms include Gabor, adaptive spectrogram, cone shape distribution, choi-williams distribution, Wigner-Ville Distribution, and Short Time Fourier Transform with different windows such as rectangular, Blackman, Hamming and Hanning. Time-frequency distribution patterns of the combustion noise are obtained, and they are compared with others from jet flow and small plastic bubble blow up.

Investigation of atmospheric pressure capillary non-thermal plasmas and their applications to the degradation of volatile organic compounds

NASA Astrophysics Data System (ADS)

Yin, Shu-Min

Atmospheric pressure capillary non-thermal plasma (AP-CNTP) has been investigated as a potential technology far the removal of volatile organic compounds (VOCs) in Advanced Life Support Systems (ALS). AP-CNTP is a destructive technology far the removal of VOCs from air streams by active plasma species, such as electrons, ions, and excited molecules. Complete VOC destruction ideally results in the formation of water, carbon dioxide (CO2), and other by-product's may also form, including ozone (O3), nitrous oxide (N2O), nitrogen dioxide (NO2), and decomposed hydrocarbons. Several organic compounds, such as BTEX, ethylene, n-heptane, isooctane, methanol and NH3, were tested in an AP-CNTP system. Parametric experiments were carried out by varying plasma discharge power, flowrates, and initial concentrations. The degradation efficiency varied depending on the chemical nature of the compounds. A plasmochemical kinetic model was derived for toluene, ethylbenzene, and m-xylene and n-heptane.

Group type analysis of asphalt by column liquid chromatography

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, C.; Yang, J.; Xue, Y.

2008-07-01

An improved analysis method for characterization of asphalt was established. The method is based on column chromatography technique. The asphalts were separated into four groups: saturates, aromatics, resins, and asphaltenes, quantitatively. About 0.1 g of sample was required in each analysis. About 20 mL of n-heptanes was used to separate out saturates first. Then about 35 mL of n-heptanes/dichloromethane (.5, v/v) mixture was used to separate out aromatics. About 30 mL of dichloromethane/tetrahydrofuran (1/3, v/v) mixture was used to separate out resin. The quality of the separation was confirmed by infrared spectra (IR) and {sup 1}H NMR analysis. The modelmore » compounds, tetracosan for saturates, dibenz(o)anthracen for aromatics, and acetanilide for resins were used for verification. The IR and {sup 1}H NMR analysis of the prepared fractions from the column liquid chromatography were in good agreement that of pure reagents.« less

TURBULENT FLAME REACTOR STUDIES OF CHLORINATED HYDROCARBON DESTRUCTION EFFICIENCY

EPA Science Inventory

Four mixtures of C₁ and C₂ chlorinated hydrocarbons, diluted in heptane, were burned in a Turbulent Flame Reactor (TFR) under high and low oxygen conditions. Emissions of undestroyed feed, stable organic by-products, carbon monoxide, carbon dioxide and oxyg...

21 CFR 177.1556 - Polyaryletherketone resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... mole, as determined by light scattering measurements in sulfuric acid at room temperature. (b) Optional... at reflux temperature for 2 hours with the following solvents: Distilled water, 50 percent (by volume) ethyl alcohol in distilled water, 3 percent acetic acid (by weight) in distilled water, and n-heptane...

Physical and Chemical Processes in Flames

DTIC Science & Technology

2010-02-15

Results: Use of comprehensively validated reduced chemical kinetic mechanism allows realistic description of methane oxidation chemistry with NOx ...PERFORMING ORGANIZATION REPORT NUMBER Department of Mechanical and Aerospace Engineering Princeton University Princeton, NJ 08544... mechanism reduction; skeletal mechanism ; CO/H2 oxidation; ethylene oxidation; heptane oxidation; directed relation graph; high-pressure combustion

Continuous and Batch Distillation in an Oldershaw Tray Column

ERIC Educational Resources Information Center

Silva, Carlos M.; Vaz, Raquel V.; Santiago, Ana S.; Lito, Patricia F.

2011-01-01

The importance of distillation in the separation field prompts the inclusion of distillation experiments in the chemical engineering curricula. This work describes the performance of an Oldershaw column in the rectification of a cyclohexane/n-heptane mixture. Total reflux distillation, continuous rectification under partial reflux, and batch…

21 CFR 177.1380 - Fluorocarbon resins.

Code of Federal Regulations, 2011 CFR

2011-04-01

... resin pellets, when extracted with 100 milliliters of distilled water at reflux temperature for 8 hours... distilled water at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.003 percent... milliliters of n-heptane at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.01...

21 CFR 177.1380 - Fluorocarbon resins.

Code of Federal Regulations, 2012 CFR

2012-04-01

... resin pellets, when extracted with 100 milliliters of distilled water at reflux temperature for 8 hours... distilled water at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.003 percent... milliliters of n-heptane at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.01...

21 CFR 177.1380 - Fluorocarbon resins.

Code of Federal Regulations, 2010 CFR

2010-04-01

... resin pellets, when extracted with 100 milliliters of distilled water at reflux temperature for 8 hours... distilled water at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.003 percent... milliliters of n-heptane at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.01...

21 CFR 177.1380 - Fluorocarbon resins.

Code of Federal Regulations, 2014 CFR

2014-04-01

... pellets, when extracted with 100 milliliters of distilled water at reflux temperature for 8 hours, shall... distilled water at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.003 percent... milliliters of n-heptane at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.01...

21 CFR 177.1380 - Fluorocarbon resins.

Code of Federal Regulations, 2013 CFR

2013-04-01

... resin pellets, when extracted with 100 milliliters of distilled water at reflux temperature for 8 hours... distilled water at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.003 percent... milliliters of n-heptane at reflux temperature for 8 hours, shall yield total extractives not to exceed 0.01...

Niosh analytical methods for Set G

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1976-12-01

Industrial Hygiene sampling and analytical monitoring methods validated under the joint NIOSH/OSHA Standards Completion Program for Set G are contained herein. Monitoring methods for the following compounds are included: butadiene, heptane, ketene, methyl cyclohexane, octachloronaphthalene, pentachloronaphthalene, petroleum distillates, propylene dichloride, turpentine, dioxane, hexane, LPG, naphtha(coal tar), octane, pentane, propane, and stoddard solvent.

LOW OZONE-DEPLETING HALOCARBONS AS TOTAL-FLOOD AGENTS: VOLUME 2. LABORATORY-SCALE FIRE SUPPRESSION AND EXPLOSION PREVENTION TESTING

EPA Science Inventory

The report gives results from (1) flame suppression testing of potential Halon-1301 (CF3Br) replacement chemicals in a laboratory cup burner using n-heptane fuel and (2) explosion prevention (inertion) testing in a small-scale explosion sphere using propane and methane as fuels. ...

40 CFR 180.319 - Interim tolerances.

Code of Federal Regulations, 2012 CFR

2012-07-01

...-oxabicyclo-(2,2,1) heptane 2,3-dicarboxylic acid Herbicide 0.2 Beet, sugar None. Isopropyl carbanilate (IPC) Herbicide 5.0 Alfalfa, hay; clover, hay; and grass, hay None. 2.0 Alfalfa, forage; clover, forage; and grass...; poultry, meat; and poultry, meat byproducts None. Methyl parathion Herbicide 0.5 Rye 12/31/13. (b) Section...

33 CFR 183.590 - Fire test.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 33 Navigation and Navigable Waters 2 2011-07-01 2011-07-01 false Fire test. 183.590 Section 183... SAFETY BOATS AND ASSOCIATED EQUIPMENT Fuel Systems Tests § 183.590 Fire test. (a) A piece of equipment is... hull section. (b) Each fire test is conducted with free burning heptane and the component must be...

Using Nuclear Magnetic Resonance Spectroscopy for Measuring Ternary Phase Diagrams

ERIC Educational Resources Information Center

Woodworth, Jennifer K.; Terrance, Jacob C.; Hoffmann, Markus M.

2006-01-01

A laboratory experiment is presented for the upper-level undergraduate physical chemistry curriculum in which the ternary phase diagram of water, 1-propanol and n-heptane is measured using proton nuclear magnetic resonance (NMR) spectroscopy. The experiment builds upon basic concepts of NMR spectral analysis, typically taught in the undergraduate…

Estimation of interfacial area in a packed cross-flow cascade with distillation of ethanol-water, methanol-water, and hexane-heptane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Velaga, A.

1986-01-01

Packed cross-flow internals consisting of four and ten stages including the samplers for liquid and vapor were fabricated to fit into the existing distillation column. Experiments were conducted using methanol-water, ethanol-water and hexane-heptane binary mixtures. The experimental data were collected for compositions of inlet and exist streams of cross-flow stages. The overall gas phase height transfer units (H/sub og/) were estimated using the experimental data. H/sub og/ values were compared to those of counter current conditions. The individual mass transfer coefficients in the liquid and vapor phases were estimated using the collected experimental data for degree of separation, flow ratesmore » and physical properties of the binary system used. The physical properties were estimated at an average temperature of the specific cross-flow stage. The mass transfer coefficients were evaluated using three different correlations proposed by Shulman. Onda and Hayashi respectively. The interfacial areas were estimated using the evaluated mass transfer coefficients and the experimental data at each stage of the column for different runs and compared.« less

Impacts created on various materials by micro-discharges in heptane: Influence of the dissipated charge

NASA Astrophysics Data System (ADS)

Hamdan, A.; Noel, C.; Kosior, F.; Henrion, G.; Belmonte, T.

2013-01-01

Modes of energy dissipation in impacts made on various materials (Al, Cu, Fe, and Si) by discharges in heptane are investigated for micro-gap conditions. Bulk metals and thin films of 300 nm in thickness deposited on silicon wafers are used as samples. Positive high voltage pulses with nanosecond rise times make it possible to isolate a single discharge and to study the way the charge delivered by the power supply is transferred to the larger electrode (the sample) in a pin-to-plate configuration. The diameter of the impacts created by the plasma varies linearly versus the charge raised at a power close to 0.5. However, the exact value of the power depends on the material. We also show how the impact morphologies change with the applied charge. At high charges, the diameters of impacts on thin films behave as those made on silicon. At low charges, they behave as the bulk material. Finally, we show that the energy dissipated in impacts is below a few percent.

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters

NASA Astrophysics Data System (ADS)

Lanjekar, R. D.; Deshmukh, D.

2018-02-01

A comparative experimental and numerical study is conducted to establish the significance of the use of single-component over multi-component representatives of biodiesel, diesel and their blend for predicting spray tip penetration. Methyl oleate and methyl laurate are used as single-component representative fuels for biodiesel. The pure components n-heptane, n-dodecane and n-tetradecane are used as single-component representative fuels for diesel. Methyl laurate is found to represent biodiesel of coconut, whereas methyl oleate is found to represent biodiesel having high percentage of long-chain fatty acid esters. The spray tip penetration of methyl oleate is found to be in good agreement with the measured spray tip penetration of karanja biodiesel. The spray tip penetration prediction of n-heptane fuel is closely following diesel spray tip penetration along with that of n-tetradecane and n-dodecane. The study suggests that the knowledge of the single-component representatives of biodiesel, diesel and their blend is sufficient to predict the spray tip penetration of the corresponding biodiesel, diesel and their blend under non-evaporating environment.

Antimicrobial activity of synthetic bornyl benzoates against Trypanosoma cruzi

PubMed Central

Corrêa, P R C; Miranda, R R S; Duarte, L P; Silva, G D F; Filho, S A Vieira; Okuma, A A; Carazza, F; Morgado-Díaz, J A; Pinge-Filho, P; Yamauchi, L M; Nakamura, C V; Yamada-Ogatta, S F

2012-01-01

We report here for the first time the in vitro effects of (1S,2R,4S)-1,7,7-trimethyl-bicyclo[2.2.1]heptan-2-yl-3′,4′,5′-trimethoxy benzoate (1) and (1S,2R,4S)-1,7,7-trimethyl-bicyclo[2.2.1]heptan-2-yl benzoate (2) on the growth and ultrastructure of Trypanosoma cruzi. These two synthetic compounds exerted an antiproliferative effect on the epimastigote forms of the parasite. The ICs50/72h of two synthetic L-bornyl benzoates, 1 and 2, was 10.1 and 12.8 μg/ml, respectively. Both compounds were more selective against epimastigotes than HEp-2 cells. Ultrastructural analysis revealed intense cytoplasmic vacuolization and the appearance of cytoplasmic materials surrounded by membranes. The treatment of peritoneal macrophages with compounds 1 and 2 caused a significant decrease in the number of T. cruzi-infected cells. L-Bornyl benzoate derivatives may serve as a potential source for the development of more effective and safer chemotherapeutic agents against T. cruzi infections. PMID:22943546

Carbon-based nanomaterial synthesis using nanosecond electrical discharges in immiscible layered liquids: n-heptane and water

NASA Astrophysics Data System (ADS)

Hamdan, Ahmad; Cha, Min Suk

2018-06-01

Plasmas in- or in-contact with liquids have been extensively investigated due to their high potential for a wide range of applications including, but not limited to, water treatment, material synthesis and functionalization, bio-medical applications, and liquid fuel reformation. Recently, we successfully developed a discharge using two immiscible liquids, having very different electrical permittivities, which could significantly intensify the electric field intensity. Here, we establish nanosecond discharges at the interface n-heptane-water (with respective relative dielectric permittivities of 2 and 80) to enable the synthesis of carbon-based nanomaterials. A characterization of the as-synthesized material and the annealed (500 °C) material, using various techniques (Fourier-transform, infra-red, scanning and transmission electron microscopes, etc), shows that the as-synthesized material is a mixture of two carbon-based phases: a crystalline phase (graphite like) embedded into a phase of hydrogenated amorphous carbon. The existence of two-phases may be explained by the non-homogeneity of the discharge that induces various chemical reactions in the plasma channel.

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters.

PubMed

Lanjekar, R D; Deshmukh, D

2018-02-01

A comparative experimental and numerical study is conducted to establish the significance of the use of single-component over multi-component representatives of biodiesel, diesel and their blend for predicting spray tip penetration. Methyl oleate and methyl laurate are used as single-component representative fuels for biodiesel. The pure components n -heptane, n -dodecane and n -tetradecane are used as single-component representative fuels for diesel. Methyl laurate is found to represent biodiesel of coconut, whereas methyl oleate is found to represent biodiesel having high percentage of long-chain fatty acid esters. The spray tip penetration of methyl oleate is found to be in good agreement with the measured spray tip penetration of karanja biodiesel. The spray tip penetration prediction of n -heptane fuel is closely following diesel spray tip penetration along with that of n -tetradecane and n -dodecane. The study suggests that the knowledge of the single-component representatives of biodiesel, diesel and their blend is sufficient to predict the spray tip penetration of the corresponding biodiesel, diesel and their blend under non-evaporating environment.

Experimental and numerical investigations on spray characteristics of fatty acid methyl esters

PubMed Central

Deshmukh, D.

2018-01-01

A comparative experimental and numerical study is conducted to establish the significance of the use of single-component over multi-component representatives of biodiesel, diesel and their blend for predicting spray tip penetration. Methyl oleate and methyl laurate are used as single-component representative fuels for biodiesel. The pure components n-heptane, n-dodecane and n-tetradecane are used as single-component representative fuels for diesel. Methyl laurate is found to represent biodiesel of coconut, whereas methyl oleate is found to represent biodiesel having high percentage of long-chain fatty acid esters. The spray tip penetration of methyl oleate is found to be in good agreement with the measured spray tip penetration of karanja biodiesel. The spray tip penetration prediction of n-heptane fuel is closely following diesel spray tip penetration along with that of n-tetradecane and n-dodecane. The study suggests that the knowledge of the single-component representatives of biodiesel, diesel and their blend is sufficient to predict the spray tip penetration of the corresponding biodiesel, diesel and their blend under non-evaporating environment. PMID:29515835

Authentication of fattening diet of Iberian pigs according to their volatile compounds profile from raw subcutaneous fat.

PubMed

Narváez-Rivas, M; Pablos, F; Jurado, J M; León-Camacho, M

2011-02-01

The composition of volatile components of subcutaneous fat from Iberian pig has been studied. Purge and trap gas chromatography-mass spectrometry has been used. The composition of the volatile fraction of subcutaneous fat has been used for authentication purposes of different types of Iberian pig fat. Three types of this product have been considered, montanera, extensive cebo and intensive cebo. With classification purposes, several pattern recognition techniques have been applied. In order to find out possible tendencies in the sample distribution as well as the discriminant power of the variables, principal component analysis was applied as visualisation technique. Linear discriminant analysis (LDA) and soft independent modelling by class analogy (SIMCA) were used to obtain suitable classification models. LDA and SIMCA allowed the differentiation of three fattening diets by using the contents in 2,2,4,6,6-pentamethyl-heptane, m-xylene, 2,4-dimethyl-heptane, 6-methyl-tridecane, 1-methoxy-2-propanol, isopropyl alcohol, o-xylene, 3-ethyl-2,2-dimethyl-oxirane, 2,6-dimethyl-undecane, 3-methyl-3-pentanol and limonene.

An Experimental Study on Burning Characteristics of n-Heptane/Ethanol Mixture Pool Fires in a Reduced Scaled Tunnel

NASA Astrophysics Data System (ADS)

Yozgatligil, Ahmet; Shafee, Sina

2016-11-01

Fire accidents in recent decades have drawn attention to safety issues associated with the design, construction and maintenance of tunnels. A reduced scale tunnel model constructed based on Froude scaling technique is used in the current work. Mixtures of n-heptane and ethanol are burned with ethanol volumetric fraction up to 30 percent and the longitudinal ventilation velocity varying from 0.5 to 2.5 m/s. The burning rates of the pool fires are measured using a precision load cell. The heat release rates of the fires are calculated according to oxygen calorimetry method and the temperature distributions inside the tunnel are also measured. Results of the experiments show that the ventilation velocity variation has a significant effect on the pool fire burning rate, smoke temperature and the critical ventilation velocity. With increased oxygen depletion in case of increased ethanol content of blended pool fires, the quasi-steady heat release rate values tend to increase as well as the ceiling temperatures while the combustion duration decreases.

Rate constant for OH with selected large alkanes : shock-tube measurements and an improved group scheme.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivaramakrishnan, R.; Michael, J. V.; Chemical Sciences and Engineering Division

High-temperature rate constant experiments on OH with the five large (C{sub 5}-C{sub 8}) saturated hydrocarbons n-heptane, 2,2,3,3-tetramethylbutane (2,2,3,3-TMB), n-pentane, n-hexane, and 2,3-dimethylbutane (2,3-DMB) were performed with the reflected-shock-tube technique using multipass absorption spectrometric detection of OH radicals at 308 nm. Single-point determinations at {approx}1200 K on n-heptane, 2,2,3,3-TMB, n-hexane, and 2,3-DMB were previously reported by Cohen and co-workers; however, the present work substantially extends the database to both lower and higher temperature. The present experiments span a wide temperature range, 789-1308 K, and represent the first direct measurements of rate constants at T > 800 K for n-pentane. The presentmore » work utilized 48 optical passes corresponding to a total path length of {approx}4.2 m. As a result of this increased path length, the high OH concentration detection sensitivity permitted pseudo-first-order analyses for unambiguously measuring rate constants.« less

Selective pressurized liquid extraction of polychlorinated biphenyls from fat-containing food and feed samples influence of cell dimensions, solvent type, temperature and flush volume.

PubMed

Sporring, Sune; Björklund, Erland

2004-06-25

Sulphuric acid impregnated silica was used for the lipid free extraction of polychlorinated biphenyls from fat containing food and feed matrices using pressurized liquid extraction on a Dionex ASE300, with 34 mL cells. Data were compared to a previous publication where extractions had been performed on a Dionex ASE200, with 33 mL cells. Four different fat/fat retainer ratios (FFRs) were tested (0.100, 0.075, 0.050 and 0.025) at 50 and 100 degrees C using n-pentane, n-hexane or n-heptane as extraction solvent. The best results were obtained with a FFR of 0.025 when applying a temperature of 100 degrees C. Both n-pentane and n-heptane were capable of replacing n-hexane as extraction solvent. A flush volume of 60% was sufficient as suggested in US Environmental Protection Agency Method 3545. The applicability of the method was demonstrated for naturally contaminated fish meal as well as various spiked and certified materials.

Prediction of warmed-over flavour development in cooked chicken by colorimetric sensor array.

PubMed

Kim, Su-Yeon; Li, Jinglei; Lim, Na-Ri; Kang, Bo-Sik; Park, Hyun-Jin

2016-11-15

The aim of this study was to develop a simple and rapid method based on colorimetric sensor array (CSA) for evaluation of warmed-over flavour (WOF) in cooked chicken. All samples were classified according to storage time by CSA coupled with principle component analysis (PCA) or hierarchical cluster analysis (HCA). The CSA data were used to establish prediction models with thiobarbituric acid reactive substances (TBARS), pentanal, hexanal, or heptanal associated with WOF by partial least square regression (PLSR). For the TBARS model, the coefficient of determination (rp(2)) was 0.9997 in the prediction range of 0.28-0.69mg/kg. In each of the models for pentanal, hexanal, and heptanal, all rp(2) were higher than 0.960 in the range of 0.58-2.10mg/kg, 5.50-11.69mg/kg, and 0.09-0.16mg/kg, respectively. These results demonstrate that the CSA was able to predict WOF development and to distinguish between each storage time. Copyright © 2016 Elsevier Ltd. All rights reserved.

DNS Study of the Ignition of n-Heptane Fuel Spray under HCCI Conditions

NASA Astrophysics Data System (ADS)

Wang, Yunliang; Rutland, Christopher J.

2004-11-01

Direct numerical simulations are carried out to investigate the mixing and auto-ignition processes of n-heptane fuel spray in a turbulent field using a skeletal chemistry mechanism with 44 species and 112 reactions. For the solution of the carrier gas fluid, we use the Eulerian method, while for the fuel spray, the Lagrangian method is used. We use an eighth-order finite difference scheme to calculate spacial derivatives and a fourth-order Runge-Kutta scheme for the time integration. The initial gas temperature is 926 K and the initial gas pressure is 30 atmospheres. The initial global equivalence ratio based on the fuel concentration is around 0.4. The initial droplet diameter is 60 macrons and the droplet temperature is 300 K. Evolutions of averaged temperature, species mass fraction, heat release and reaction rate are presented. Contours of temperature and species mass fractions are presented. The objective is to understand the mechanism of ignition under Homogeneous Charged Compression Ignition (HCCI) conditions, aiming at providing some useful information of HCCI combustion, which is one of the critical issues to be resolved.

Adsorption of non-ionic ABC triblock copolymers: Surface modification of TiO2 suspensions in aqueous and non-aqueous medium

NASA Astrophysics Data System (ADS)

Lerch, Jean-Philippe; Atanase, Leonard Ionut; Riess, Gérard

2017-10-01

A series of non-ionic ABC triblock copolymers, such as poly(butadiene)-b-poly(2-vinylpyrridine)-b-poly(ethylene oxide) (PB-P2VP-PEO) were synthesized by sequential anionic polymerizations. For these copolymers comprising an organo-soluble PB and a water-soluble PEO block, their P2VP middle block has been selected for its anchoring capacity on solid surfaces. The adsorption isotherms on TiO2 were obtained in heptane and in aqueous medium, as selective solvents. In both of these cases, the P2VP middle block provides the surface anchoring, whereas PB and PEO sequences are acting as stabilizing moieties in heptane and water respectively. By extension to ABC triblock copolymers of the scaling theory developed for diblock copolymers, the density of adsorbed chains could be correlated with the molecular characteristics of the PB-P2VP-PEO triblock copolymers. From a practical point a view, it could be demonstrated that these copolymers are efficient dispersing agents for the TiO2 pigments in both aqueous and non-aqueous medium.

The combined effect of food-simulating solutions, brushing and staining on color stability of composite resins

PubMed Central

Silva, Tânia Mara Da; Sales, Ana Luísa Leme Simões; Pucci, Cesar Rogerio; Borges, Alessandra Bühler; Torres, Carlos Rocha Gomes

2017-01-01

Abstract Objective: This study evaluated the effect of food-simulating media associated with brushing and coffee staining on color stability of different composite resins. Materials and methods: Eighty specimens were prepared for each composite: Grandio SO (Voco), Amaris (Voco), Filtek Z350XT (3M/ESPE), Filtek P90 (3M/ESPE). They were divided into four groups according to food-simulating media for 7 days: artificial saliva (control), heptane, citric acid and ethanol. The composite surface was submitted to 10,950 brushing cycles (200 g load) in an automatic toothbrushing machine. The specimens were darkened with coffee solution at 37 °C for 24 h. After each treatment, color measurements were assessed by spectrophotometry, using CIE L*a*b* system. The overall color change (ΔE) was determined for each specimen at baseline (C1) and after the treatments (food-simulating media immersion/C2, brushing/C3 and dye solution/C4). Data were analyzed by two-way repeated measures ANOVA and Tukey’s tests (p < .05). Results: The results of RM-ANOVA showed significant differences for composites (p = .001), time (p = .001) and chemical degradation (p = .002). The mean of ΔE for composites were: Z350XT (5.39)a, Amaris (3.89)b, Grandio (3.75)bc, P90 (3.36)c. According to food-simulating media: heptane (4.41)a, citric acid (4.24)a, ethanol (4.02)ab, artificial saliva (3.76)b. For the treatments: dye solution (4.53)a, brushing (4.26)a, after food-simulating media (3.52)b. Conclusions: The composite resin Filtek Z350XT showed significantly higher staining than all other composite resin tested. The immersion in heptane and citric acid produced the highest color alteration than other food-simulating media. The exposure of samples to brushing protocols and darkening in coffee solution resulted in significant color alteration of the composite resins. PMID:28642926

The role of cool-flame chemistry in quasi-steady combustion and extinction of n-heptane droplets

NASA Astrophysics Data System (ADS)

Paczko, Guenter; Peters, Norbert; Seshadri, Kalyanasundaram; Williams, Forman Arthur

2014-09-01

Experiments on the combustion of large n-heptane droplets, performed by the National Aeronautics and Space Administration in the International Space Station, revealed a second stage of continued quasi-steady burning, supported by low-temperature chemistry, that follows radiative extinction of the first stage of burning, which is supported by normal hot-flame chemistry. The second stage of combustion experienced diffusive extinction, after which a large vapour cloud was observed to form around the droplet. In the present work, a 770-step reduced chemical-kinetic mechanism and a new 62-step skeletal chemical-kinetic mechanism, developed as an extension of an earlier 56-step mechanism, are employed to calculate the droplet burning rates, flame structures, and extinction diameters for this cool-flame regime. The calculations are performed for quasi-steady burning with the mixture fraction as the independent variable, which is then related to the physical variables of droplet combustion. The predictions with the new mechanism, which agree well with measured autoignition times, reveal that, in decreasing order of abundance, H2O, CO, H2O2, CH2O, and C2H4 are the principal reaction products during the low-temperature stage and that, during this stage, there is substantial leakage of n-heptane and O2 through the flame, and very little production of CO2 with no soot in the mechanism. The fuel leakage has been suggested to be the source of the observed vapour cloud that forms after flame extinction. While the new skeletal chemical-kinetic mechanism facilitates understanding of the chemical kinetics and predicts ignition times well, its predicted droplet diameters at extinction are appreciably larger than observed experimentally, but predictions with the 770-step reduced chemical-kinetic mechanism are in reasonably good agreement with experiment. The computations show how the key ketohydroperoxide compounds control the diffusion-flame structure and its extinction.

Self-ignition of S.I. engine model fuels: A shock tube investigation at high pressure

DOE Office of Scientific and Technical Information (OSTI.GOV)

Fieweger, K.; Blumenthal, R.; Adomeit, G.

1997-06-01

The self-ignition of several spark-ignition (SI) engine fuels (iso-octane, methanol, methyl tert-butyl ether and three different mixtures of iso-octane and n-heptane), mixed with air, was investigated experimentally under relevant engine conditions by the shock tube technique. Typical modes of the self-ignition process were registered cinematographically. For temperatures relevant to piston engine combustion, the self-ignition process always starts as an inhomogeneous, deflagrative mild ignition. This instant is defined by the ignition delay time, {tau}{sub defl}. The deflagration process in most cases is followed by a secondary explosion (DDT). This transition defines a second ignition delay time, {tau}{sub DDT}, which is amore » suitable approximation for the chemical ignition delay time, if the change of the thermodynamic conditions of the unburned test gas due to deflagration is taken into account. For iso-octane at p = 40 bar, a NTC (negative temperature coefficient), behavior connected with a two step (cool flame) self-ignition at low temperatures was observed. This process was very pronounced for rich and less pronounced for stoichiometric mixtures. The results of the {tau}{sub DDT} delays of the stoichiometric mixtures were shortened by the primary deflagration process in the temperature range between 800 and 1,000 K. Various mixtures of iso-octane and n-heptane were investigated. The results show a strong influence of the n-heptane fraction in the mixture, both on the ignition delay time and on the mode of self-ignition. The self-ignition of methanol and MTBE (methyl tert-butyl ether) is characterized by a very pronounced initial deflagration. For temperatures below 900 K (methanol: 800 K), no secondary explosion occurs. Taking into account the pressure increase due to deflagration, the measured delays {tau}{sub DDT} of the secondary explosion are shortened by up to one order of magnitude.« less

Some Recent Observations on the Burning of Isolated N-Heptane and Alcohol Droplets

NASA Technical Reports Server (NTRS)

Dryer, F. L.; Kazakov, A.; Urban, B. D.

2001-01-01

In a joint program involving Prof. F.A. Williams of the University of California, San Diego and Dr. V. Nayagam of the National Center for Microgravity Research on Combustion and Fluid Dynamics, the combustion of liquid fuel droplets of n-heptane, n-decane, methanol, methanol-water, ethanol and ethanol-water having initial diameters between about 1 mm and 6 mm continues to be studied. The objectives of the work are to improve fundamental knowledge of droplet combustion dynamics for pure fuels and fuel-water mixtures through microgravity experiments and theoretical analyses. The Princeton contributions to the collaborative program supports the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies through experiments and numerical modeling. The complementary UCSD contributions apply asymptotic theoretical analyses and are described in the published literature and in a companion communication in this conference. The combined program continues to focus on analyses of results obtained from Fiber Supported Droplet Combustion (FSDC) experiments (FSDC-2, STS- 94) conducted with the above fuels in shuttle cabin air and Droplet Combustion Experiment (DCE) data obtained for unsupported and fiber supported droplets of n-heptane in Helium-Oxygen mixtures and cabin air (STS-83, STS-94). The program is preparing for a second DCE experimental mission using methanol/methanol-water as fuels and helium-oxygen-nitrogen environments. DCE-2 is to be conducted aboard the International Space Station. Emphases of recent Princeton work are on the study of simple alcohols (methanol, ethanol) and alcohol/water mixtures as fuels, with time-dependent measurements of drop size, flame-standoff, liquid-phase composition, and finally, extinction. Ground based experiments have included bench-scale studies at Princeton and collaborative experimental studies in the 2.2 second drop tower at NASA-Glenn Research Center.

A Detailed Chemical Kinetic Reaction Mechanism for n-Alkane Hydrocarbons From n-Octane to n-Hexadecane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westbrook, C K; Pitz, W J; Herbinet, O

2008-02-08

Detailed chemical kinetic reaction mechanisms have been developed to describe the pyrolysis and oxidation of nine n-alkanes larger than n-heptane, including n-octane (n-C{sub 8}H{sub 18}), n-nonane (n-C{sub 9}H{sub 20}), n-decane (n-C{sub 10}H{sub 22}), n-undecane (n-C{sub 11}H{sub 24}), n-dodecane (n-C{sub 12}H{sub 26}), n-tridecane (n-C{sub 13}H{sub 28}), n-tetradecane (n-C{sub 14}H{sub 30}), n-pentadecane (n-C{sub 15}H{sub 32}), and n-hexadecane (n-C{sub 16}H{sub 34}). These mechanisms include both high temperature and low temperature reaction pathways. The mechanisms are based on our previous mechanisms for the primary reference fuels n-heptane and iso-octane, using the reaction class mechanism construction first developed for n-heptane. Individual reaction class rules aremore » as simple as possible in order to focus on the parallelism between all of the n-alkane fuels included in the mechanisms, and these mechanisms will be refined further in the future to incorporate greater levels of accuracy and predictive capability. These mechanisms are validated through extensive comparisons between computed and experimental data from a wide variety of different sources. In addition, numerical experiments are carried out to examine features of n-alkane combustion in which the detailed mechanisms can be used to compare reactivities of different n-alkane fuels. The mechanisms for all of these n-alkanes are presented as a single detailed mechanism, which can be edited to produce efficient mechanisms for any of the n-alkanes included, and the entire mechanism, with supporting thermochemical and transport data, together with an explanatory glossary explaining notations and structural details, will be available for download from our web page.« less

Acceleration of the chemistry solver for modeling DI engine combustion using dynamic adaptive chemistry (DAC) schemes

NASA Astrophysics Data System (ADS)

Shi, Yu; Liang, Long; Ge, Hai-Wen; Reitz, Rolf D.

2010-03-01

Acceleration of the chemistry solver for engine combustion is of much interest due to the fact that in practical engine simulations extensive computational time is spent solving the fuel oxidation and emission formation chemistry. A dynamic adaptive chemistry (DAC) scheme based on a directed relation graph error propagation (DRGEP) method has been applied to study homogeneous charge compression ignition (HCCI) engine combustion with detailed chemistry (over 500 species) previously using an R-value-based breadth-first search (RBFS) algorithm, which significantly reduced computational times (by as much as 30-fold). The present paper extends the use of this on-the-fly kinetic mechanism reduction scheme to model combustion in direct-injection (DI) engines. It was found that the DAC scheme becomes less efficient when applied to DI engine simulations using a kinetic mechanism of relatively small size and the accuracy of the original DAC scheme decreases for conventional non-premixed combustion engine. The present study also focuses on determination of search-initiating species, involvement of the NOx chemistry, selection of a proper error tolerance, as well as treatment of the interaction of chemical heat release and the fuel spray. Both the DAC schemes were integrated into the ERC KIVA-3v2 code, and simulations were conducted to compare the two schemes. In general, the present DAC scheme has better efficiency and similar accuracy compared to the previous DAC scheme. The efficiency depends on the size of the chemical kinetics mechanism used and the engine operating conditions. For cases using a small n-heptane kinetic mechanism of 34 species, 30% of the computational time is saved, and 50% for a larger n-heptane kinetic mechanism of 61 species. The paper also demonstrates that by combining the present DAC scheme with an adaptive multi-grid chemistry (AMC) solver, it is feasible to simulate a direct-injection engine using a detailed n-heptane mechanism with 543 species with practical computer time.

Three-dimensional quantitative structure-activity relationship CoMSIA/CoMFA and LeapFrog studies on novel series of bicyclo [4.1.0] heptanes derivatives as melanin-concentrating hormone receptor R1 antagonists.

PubMed

Morales-Bayuelo, Alejandro; Ayazo, Hernan; Vivas-Reyes, Ricardo

2010-10-01

Comparative molecular similarity indices analysis (CoMSIA) and comparative molecular field analysis (CoMFA) were performed on a series of bicyclo [4.1.0] heptanes derivatives as melanin-concentrating hormone receptor R1 antagonists (MCHR1 antagonists). Molecular superimposition of antagonists on the template structure was performed by database alignment method. The statistically significant model was established on sixty five molecules, which were validated by a test set of ten molecules. The CoMSIA model yielded the best predictive model with a q(2) = 0.639, non cross-validated R(2) of 0.953, F value of 92.802, bootstrapped R(2) of 0.971, standard error of prediction = 0.402, and standard error of estimate = 0.146 while the CoMFA model yielded a q(2) = 0.680, non cross-validated R(2) of 0.922, F value of 114.351, bootstrapped R(2) of 0.925, standard error of prediction = 0.364, and standard error of estimate = 0.180. CoMFA analysis maps were employed for generating a pseudo cavity for LeapFrog calculation. The contour maps obtained from 3D-QSAR studies were appraised for activity trends for the molecules analyzed. The results show the variability of steric and electrostatic contributions that determine the activity of the MCHR1 antagonist, with these results we proposed new antagonists that may be more potent than previously reported, these novel antagonists were designed from the addition of highly electronegative groups in the substituent di(i-C(3)H(7))N- of the bicycle [4.1.0] heptanes, using the model CoMFA which also was used for the molecular design using the technique LeapFrog. The data generated from the present study will further help to design novel, potent, and selective MCHR1 antagonists. Copyright (c) 2010 Elsevier Masson SAS. All rights reserved.

Alkanes and terpenes in wood and leaves of Pinus jeffreyi and P. sabiniana

Treesearch

Robert P. Adams; Jessica W. Wright

2012-01-01

The wood oils of Pinus jeffreyi and P. sabiniana contain considerable amounts of heptane (76.6%, 92%), on a monoterpene basis. However, when entire wood extractables is considered, the amounts drop considerably (3.4%, 36.8%) with the major portion of the wood oils being diterpene acids. The leaf oil of P. jeffreyi...

2-[Anilino(phen-yl)meth-yl]cyclo-heptan-one.

PubMed

Eftekhari-Sis, Bagher; Mohajer, Sahar; Zirak, Maryam; Mozaffarnia, Sakineh; Büyükgüngör, Orhan

2013-01-01

In the title compound, C20H23NO, the cyclo-hepta-none ring adopts a twist-chair conformation, with the amino-methyl substituent in an equatorial position. The relative configuration of the two stereocenters is R,R. In the crystal, mol-ecules are linked by N-H⋯O hydrogen bonds into chains along [100].

Additives for Water Mist Fire Suppression Systems: A Review

DTIC Science & Technology

2012-11-01

TM 2012-236; R & D pour la défense Canada – Atlantique; novembre 2012. Introduction : On utilisait les halons comme agents extincteurs dans les... 13 Table 11: Results of fire extinguishment tests on kerosene or heptanes pan fires using water mist and water mist with 2 vol...Forafac® WM. ....................................................... 13 x DRDC Atlantic TM 2012-236 This page intentionally left

21 CFR 177.1050 - Acrylonitrile/styrene copoly-mer modified with butadiene/styrene elastomer.

Code of Federal Regulations, 2014 CFR

2014-04-01

... for use E, F, or G described in table 2 of § 176.170(c) of this chapter. (a) Identity. For the purpose... with 250 milliliters spectral grade n-heptane at reflux temperature for 2 hours. (e) Accelerated extraction end test. The modified copolymer shall yield acrylonitrile monomer not in excess of 0.4 ppm when...

21 CFR 177.1050 - Acrylonitrile/styrene copoly-mer modified with butadiene/styrene elastomer.

Code of Federal Regulations, 2013 CFR

2013-04-01

... chapter as Type VI-B under conditions for use E, F, or G described in table 2 of § 176.170(c) of this... copol-ymer is extracted with 250 milliliters spectral grade n-heptane at reflux temperature for 2 hours. (e) Accelerated extraction end test. The modified copolymer shall yield acrylonitrile monomer not in...

21 CFR 177.1050 - Acrylonitrile/styrene copoly-mer modified with butadiene/styrene elastomer.

Code of Federal Regulations, 2011 CFR

2011-04-01

... chapter as Type VI-B under conditions for use E, F, or G described in table 2 of § 176.170(c) of this... copol-ymer is extracted with 250 milliliters spectral grade n-heptane at reflux temperature for 2 hours. (e) Accelerated extraction end test. The modified copolymer shall yield acrylonitrile monomer not in...

21 CFR 177.1050 - Acrylonitrile/styrene copoly-mer modified with butadiene/styrene elastomer.

Code of Federal Regulations, 2012 CFR

2012-04-01

... chapter as Type VI-B under conditions for use E, F, or G described in table 2 of § 176.170(c) of this... copol-ymer is extracted with 250 milliliters spectral grade n-heptane at reflux temperature for 2 hours. (e) Accelerated extraction end test. The modified copolymer shall yield acrylonitrile monomer not in...

[Identification of migrants from nitrile-butadiene rubber gloves].

PubMed

Mutsuga, Motoh; Kawamura, Yoko; Wakui, Chiseko; Maitani, Tamio

2003-04-01

Polyvinyl chloride gloves containing di(2-ethylhexyl) phthalate are restricted for food contact use. In their place, disposable gloves made from nitrile-butadiene rubber (NBR) are used in contact with foodstuffs. Some unknown substances were found to migrate into n-heptane from NBR gloves. By GC/MS, HR-MS and NMR, their chemical structures were confirmed to be 2,2,4-trimethyl-1,3-pentanediol diisobutyrate (used as a plasticizer), 4,4'-butylidenedi(6-tert-butyl-m-cresol), a mixture of styrenated phenols consisting of 2-(alpha-methylbenzyl)phenol, 4-(alpha-methylbenzyl)phenol, 2,6-di(alpha-methylbenzyl)phenol, 2,4-di(alpha-methylbenzyl)phenol and 2,4,6-tri(alpha-methylbenzyl)phenol (used as antioxidants), and 2,4-di-tert-butylphenol, which seems to a degradation product of antioxidant. Migration levels of these compounds were 1.68 micrograms/cm2 of 2,4-di-tert-butylphenol, 2.80 micrograms/cm2 of 2,2,4-trimethyl-1,3-pentanediol diisobutyrate, 46.08 micrograms/cm2 of styrenated phenols and 4.22 micrograms/cm2 of 4,4'-butylidenedi(6-tert-butyl-m-cresol) into n-heptane, respectively. The content of total styrenated phenols was 6,900 micrograms/g in NBR gloves.

Occurrence of high gravity oil in an Oligocene Vicksburg age sandstone in Jim Hogg County, Texas

DOE Office of Scientific and Technical Information (OSTI.GOV)

Smith, L.W.; Hilton, N.

1980-01-01

On October 1, 1979 the Guardian Oil Co. E-1 Mestena oil and gas well was completed in an Oligocene, Vicksburg sandstone. The initial potential was 245 BOPD of 75 API gravity oil. A hydrocarbon analysis of a sample obtained from the E-1 well revealed an oil composed primarily of propane and butane with a significant portion of pentane to heptane range material which accounts for the exceptionally high gravity of the liquid hydrocarbons. This analysis further showed that the E-1 well is producing almost no methane, ethane, or other hydrocarbons of greater molecular weight than nonane. Several faults, adjacent tomore » the well, could have provided a path of migration for the hydrocarbons. A detailed analysis of the butane to heptane fluid produced by the E-1 well indicated the fluid contained a large amount of compounds characteristic of an immature crude. Coal fragments present in the cutting from a nearby well and the regional geology of the Vicksburg Formation suggest that one possible source for the hydrocarbons of the E-1 well could have been lipid rich Cannel-type coal.« less

A novel sorptive extraction method based on polydimethylsiloxane frit for determination of lung cancer biomarkers in human serum.

PubMed

Xu, Hui; Wang, Shuyu

2012-04-29

In this study, a porous polypropylene frit was coated with polydimethylsiloxane (PDMS) as extraction medium, based on the home-made PDMS-frit, a rapid, simple and sensitive sorptive extraction method was established for analysis of potential biomarkers of lung cancer (hexanal and heptanal) in human serum samples. In the method, derivatization and extraction occurred simultaneously on the PDMS-frit, then the loaded frit was ultrasonically desorbed in acetonitrile. Polymerization, derivatization-extraction and desorption conditions were optimized. Under the optimal conditions, satisfactory results were gained, a wide linear application range was obtained in the range of 0.002-5.0 μmol L(-1) (R>0.997) for two aldehydes, the detection limits (SN(-1)=3) were 0.5 nmol L(-1) for hexanal and 0.4 nmol L(-1) for heptanal. The relative standard deviations (RSDs, n=5) of the method were below 7.9% and the recoveries were above 72.7% for the spiked serum. All these results hint that the proposed method is potential for disease markers analysis in complex biological samples. Copyright © 2012 Elsevier B.V. All rights reserved.

[Interlaboratory Study on Evaporation Residue Test for Food Contact Products (Report 2)].

PubMed

Ohno, Hiroyuki; Mutsuga, Motoh; Abe, Tomoyuki; Abe, Yutaka; Amano, Homare; Ishihara, Kinuyo; Ohsaka, Ikue; Ohno, Haruka; Ohno, Yuichiro; Ozaki, Asako; Kakihara, Yoshiteru; Kobayashi, Hisashi; Sakuragi, Hiroshi; Shibata, Hiroshi; Shirono, Katsuhiro; Sekido, Haruko; Takasaka, Noriko; Takenaka, Yu; Tajima, Yoshiyasu; Tanaka, Aoi; Tanaka, Hideyuki; Nakanishi, Toru; Nomura, Chie; Haneishi, Nahoko; Hayakawa, Masato; Miura, Toshihiko; Yamaguchi, Miku; Yamada, Kyohei; Watanabe, Kazunari; Sato, Kyoko

2018-01-01

An interlaboratory study was performed to evaluate the equivalence between an official method and a modified method of evaporation residue test using heptane as a food-simulating solvent for oily or fatty foods, based on the Japanese Food Sanitation Law for food contact products. Twenty-three laboratories participated, and tested the evaporation residues of nine test solutions as blind duplicates. In the official method, heating for evaporation was done with a water bath. In the modified method, a hot plate was used for evaporation, and/or a vacuum concentration procedure was skipped. In most laboratories, the test solutions were heated until just prior to dryness, and then allowed to dry under residual heat. Statistical analysis revealed that there was no significant difference between the two methods. Accordingly, the modified method provides performance equal to the official method, and is available as an alternative method. Furthermore, an interlaboratory study was performed to evaluate and compare two leaching solutions (95% ethanol and isooctane) used as food-simulating solvents for oily or fatty foods in the EU. The results demonstrated that there was no significant difference between heptane and these two leaching solutions.

Multicomponent synthesis of some new (1S,4S)-2,5-diazabicyclo[2.2.1]heptane-dithiocarbamates and their in vitro anti-proliferative activity against CaSki, MDA-MB-231 and SK-Lu-1 tumour cells as apoptosis inducing agents without necrosis.

PubMed

Laskar, Sujay; Sánchez-Sánchez, Luis; López-Ortiz, Manuel; López-Muñoz, Hugo; Escobar-Sánchez, María L; Sánchez, Arturo T; Regla, Ignacio

2017-12-01

Identification of a new class of antitumor agent capable to induce apoptosis without triggering necrotic cell death event is challenging. The present communication describes the multicomponent synthesis of seven new (1S,4S)-2,5-diazabicyclo[2.2.1]heptane-dithiocarbamates and their in vitro antiproliferative activity on cervical cancer cell line (CaSki), breast cancer cell line (MDA-MB231), lung cancer cell line (SK-Lu-1) and human lymphocytes. Among the synthesized dithiocarbamates, compound 9e displayed significant antiproliferative activity without inducing any necrotic cell death (both on tumour cells and lymphocytes) and induced apoptosis in tumor cells by the caspase dependent apoptotic pathway. The compound 9e also exhibited greater tumor selectivity than human lymphocytes. In silico ADME predictions revealed that compound 9e has the potential to be developed as a drug candidate. Rapid chemical modifications of this lead are thus highly necessary for further investigation as a drug like safer antitumor candidate and also to achieve compounds with better activity profile.

High laser efficiency and photostability of pyrromethene dyes mediated by nonpolar solvent.

PubMed

Gupta, Monika; Kamble, Priyadarshini; Rath, M C; Naik, D B; Ray, Alok K

2015-08-10

Many pyrromethene (PM) dyes have been shown to outperform established rhodamine dyes in terms of laser efficiency in the green-yellow spectral region, but their rapid photochemical degradation in commonly used ethanol or methanol solvents continues to limit its use in high average power liquid dye lasers. A comparative study on narrowband laser efficiency and photostability of commercially available PM567 and PM597 dyes, using nonpolar n-heptane and 1,4-dioxane and polar ethanol solvents, was carried out by a constructed pulsed dye laser, pumped by the second harmonic (532 nm) radiation of a Q-switched Nd:YAG laser. Interestingly, both nonpolar solvents showed a significantly higher laser photostability (∼100 times) as well as peak efficiency (∼5%) of these PM dyes in comparison to ethanol. The different photostability of the PM dyes was rationalized by determining their triplet-state spectra and capability to generate reactive singlet oxygen (O₂1) by energy transfer to dissolved oxygen in these solvents using pulse radiolysis. Heptane is identified as a promising solvent for these PM dyes for use in high average power dye lasers, pumped by copper vapor lasers or diode-pumped solid-state green lasers.

Preparative isolation of huperzines A and B from Huperzia serrata by displacement centrifugal partition chromatography.

PubMed

Toribio, Alix; Delannay, Eldra; Richard, Bernard; Plé, Karen; Zèches-Hanrot, Monique; Nuzillard, Jean-Marc; Renault, Jean-Hugues

2007-01-26

The pH-zone refining centrifugal partition chromatography technique was used to separate the two acetylcholinesterase inhibitors huperzines A and B from a crude alkaloid extract of the club moss Huperzia serrata. Complete co-elution of huperzines A and B was initially observed with the well-known methyl tert-butyl ether-acetonitrile-water (4:1:5, v/v/v) solvent system with triethylamine (8mM) as the displacer and methane sulfonic acid (6mM) as the retainer. An efficient biphasic system was designed on the basis of solvent association that provided selectivity in the elution mode: n-heptane/ethyl acetate/n-propanol/water (5:15:35:45, v/v/v/v). Lowering the bridge solvent content (n-propanol) of this system increased the polarity difference between the two phases thus adapting it to the pH-zone refining mode. Thus, the purification of these compounds was achieved using the biphasic system n-heptane/ethyl acetate/n-propanol/water (10:30:15:45, v/v/v/v) with triethylamine (8mM) as the displacer and methane sulfonic acid (6mM) as the retainer.

Membrane-assisted extraction of monoterpenes: from in silico solvent screening towards biotechnological process application

PubMed Central

2018-01-01

This work focuses on the process development of membrane-assisted solvent extraction of hydrophobic compounds such as monoterpenes. Beginning with the choice of suitable solvents, quantum chemical calculations with the simulation tool COSMO-RS were carried out to predict the partition coefficient (logP) of (S)-(+)-carvone and terpinen-4-ol in various solvent–water systems and validated afterwards with experimental data. COSMO-RS results show good prediction accuracy for non-polar solvents such as n-hexane, ethyl acetate and n-heptane even in the presence of salts and glycerol in an aqueous medium. Based on the high logP value, n-heptane was chosen for the extraction of (S)-(+)-carvone in a lab-scale hollow-fibre membrane contactor. Two operation modes are investigated where experimental and theoretical mass transfer values, based on their related partition coefficients, were compared. In addition, the process is evaluated in terms of extraction efficiency and overall product recovery, and its biotechnological application potential is discussed. Our work demonstrates that the combination of in silico prediction by COSMO-RS with membrane-assisted extraction is a promising approach for the recovery of hydrophobic compounds from aqueous solutions. PMID:29765654

Kinetic modelling of the oxidation of large aliphatic hydrocarbons using an automatic mechanism generation.

PubMed

Muharam, Yuswan; Warnatz, Jürgen

2007-08-21

A mechanism generator code to automatically generate mechanisms for the oxidation of large hydrocarbons has been successfully modified and considerably expanded in this work. The modification was through (1) improvement of the existing rules such as cyclic-ether reactions and aldehyde reactions, (2) inclusion of some additional rules to the code, such as ketone reactions, hydroperoxy cyclic-ether formations and additional reactions of alkenes, (3) inclusion of small oxygenates, produced by the code but not included in the handwritten C(1)-C(4) sub-mechanism yet, to the handwritten C(1)-C(4) sub-mechanism. In order to evaluate mechanisms generated by the code, simulations of observed results in different experimental environments have been carried out. Experimentally derived and numerically predicted ignition delays of n-heptane-air and n-decane-air mixtures in high-pressure shock tubes in a wide range of temperatures, pressures and equivalence ratios agree very well. Concentration profiles of the main products and intermediates of n-heptane and n-decane oxidation in jet-stirred reactors at a wide range of temperatures and equivalence ratios are generally well reproduced. In addition, the ignition delay times of different normal alkanes was numerically studied.

Two novel solvent system compositions for protected synthetic peptide purification by centrifugal partition chromatography.

PubMed

Amarouche, Nassima; Giraud, Matthieu; Forni, Luciano; Butte, Alessandro; Edwards, F; Borie, Nicolas; Renault, Jean-Hugues

2014-04-11

Protected synthetic peptide intermediates are often hydrophobic and not soluble in most common solvents. They are thus difficult to purify by preparative reversed-phase high-performance liquid chromatography (RP-HPLC), usually used for industrial production. It is then challenging to develop alternative chromatographic purification processes. Support-free liquid-liquid chromatographic techniques, including both hydrostatic (centrifugal partition chromatography or CPC) and hydrodynamic (counter-current chromatography or CCC) devices, are mainly involved in phytochemical studies but have also been applied to synthetic peptide purification. In this framework, two new biphasic solvent system compositions covering a wide range of polarity were developed to overcome solubility problems mentioned above. The new systems composed of heptane/tetrahydrofuran/acetonitrile/dimethylsulfoxide/water and heptane/methyl-tetrahydrofuran/N-methylpyrrolidone/water were efficiently used for the CPC purification of a 39-mer protected exenatide (Byetta®) and a 8-mer protected peptide intermediate of bivalirudin (Angiox®) synthesis. Phase compositions of the different biphasic solvent systems were determined by (1)H nuclear magnetic resonance. Physico-chemical properties including viscosity, density and interfacial tension of these biphasic systems are also described. Copyright © 2014 Elsevier B.V. All rights reserved.

The effect of azeotropism on combustion characteristics of blended fuel pool fire.

PubMed

Ding, Yanming; Wang, Changjian; Lu, Shouxiang

2014-04-30

The effect of azeotropism on combustion characteristics of blended fuel pool fire was experimentally studied in an open fire test space of State Key Laboratory of Fire Science. A 30 cm × 30 cm square pool filled with n-heptane and ethanol blended fuel was employed. Flame images, burning rate and temperature distribution were collected and recorded in the whole combustion process. Results show that azeotropism obviously dominates the combustion behavior of n-heptane/ethanol blended fuel pool fire. The combustion process after ignition exhibits four typical stages: initial development, azeotropic burning, single-component burning and decay stage. Azeotropism appears when temperature of fuel surface reaches azeotropic point and blended fuel burns at azeotropic ratio. Compared with individual pure fuel, the effect of azeotropism on main fire parameters, such as flame height, burning rate, flame puffing frequency and centerline temperature were analyzed. Burning rate and centerline temperature of blended fuel are higher than that of individual pure fuel respectively at azeotropic burning stage, and flame puffing frequency follows the empirical formula between Strouhal and Froude number for pure fuel. Copyright © 2014 Elsevier B.V. All rights reserved.

Alternatives for Benzene in the Extraction of Bitumen Fume from Exposure Sample Media.

PubMed

Sutter, Benjamin; Ravera, Christel; Hussard, Caroline; Langlois, Eddy

2016-01-01

Benzene is frequently used to extract collected bitumen fumes from personal sampler substrates. However, this solvent is particularly dangerous because of its carcinogenicity (group 1 of the International Agency for Research on Cancer classification). Therefore, to prevent the exposure of laboratory technicians to benzene during the fume extraction step from samplers, a compromise had to be found to identify a less toxic solvent with the same extraction capacity. To compare the extraction capacities of selected solvents, bitumen fumes were generated in the laboratory from three different batches of road surfacing bitumen collected on dedicated bitumen fume samplers. The samplers were then extracted by benzene and the solvents tested. Of 11 selected solvents less toxic than benzene and used in studies on bitumen and bitumen fume analyses, n-hexane and n-heptane were identified as alternatives to benzene. In particular, the results demonstrated that n-heptane was the best candidate solvent for benzene replacement, due to its extraction efficiency comparable to benzene for the three bitumen fumes tested and its low toxicity, which is highly compatible with benzene replacement. © The Author 2015. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Quantitative Laser-Saturated Fluorescence Measurements of Nitric Oxide in a Heptane Spray Flame

NASA Technical Reports Server (NTRS)

Cooper, Clayton S.; Laurendeau, Normand M.; Lee, Chi (Technical Monitor)

1997-01-01

We report spatially resolved laser-saturated fluorescence measurements of NO concentration in a pre-heated, lean-direct injection (LDI) spray flame at atmospheric pressure. The spray is produced by a hollow-cone, pressure-atomized nozzle supplied with liquid heptane. NO is excited via the Q2(26.5) transition of the gamma(0,0) band. Detection is performed in a 2-nm region centered on the gamma(0,1) band. Because of the relatively close spectral spacing between the excitation (226 nm) and detection wavelengths (236 nm), the gamma(0,1) band of NO cannot be isolated from the spectral wings of the Mie scattering signal produced by the spray. To account for the resulting superposition of the fluorescence and scattering signals, a background subtraction method has been developed that utilizes a nearby non-resonant wavelength. Excitation scans have been performed to locate the optimum off-line wavelength. Detection scans have been performed at problematic locations in the flame to determine possible fluorescence interferences from UHCs and PAHs at both the on-line and off-line excitation wavelengths. Quantitative radial NO profiles are presented and analyzed so as to better understand the operation of lean-direct injectors for gas turbine combustors.

High pressure combustion of liquid fuels. [alcohol and n-paraffin fuels

NASA Technical Reports Server (NTRS)

Canada, G. S.

1974-01-01

Measurements were made of the burning rates and liquid surface temperatures for a number of alcohol and n-paraffin fuels under natural and forced convection conditions. Porous spheres ranging in size from 0.64-1.9 cm O.D. were emloyed to simulate the fuel droplets. The natural convection cold gas tests considered the combustion in air of methanol, ethanol, propanol-1, n-pentane, n-heptane, and n-decane droplets at pressures up to 78 atmospheres. The pressure levels of the natural convection tests were high enough so that near critical combustion was observed for methanol and ethanol vaporization rates and liquid surface temperature measurements were made of droplets burning in a simulated combustion chamber environment. Ambient oxygen molar concentrations included 13%, 9.5% and pure evaporation. Fuels used in the forced convection atmospheric tests included those listed above for the natural convection tests. The ambient gas temperature ranged from 600 to 1500 K and the Reynolds number varied from 30 to 300. The high pressure forced convection tests employed ethanol and n-heptane as fuels over a pressure range of one to 40 atmospheres. The ambient gas temperature was 1145 K for the two combustion cases and 1255 K for the evaporation case.

Characterization and quantification of odor-active compounds in unsaturated fatty acid/conjugated linoleic acid (UFA/CLA)-enriched butter and in conventional butter during storage and induced oxidation.

PubMed

Mallia, Silvia; Escher, Felix; Dubois, Sébastien; Schieberle, Peter; Schlichtherle-Cerny, Hedwig

2009-08-26

Dairy products enriched in unsaturated fatty acids (UFA) and conjugated linoleic acids (CLA) have a higher nutritional value and are suggested to have beneficial health effects. However, such acids are susceptible to oxidation, and off-flavors may be formed during storage. This study was aimed to compare the most important odorants in UFA/CLA-enriched butter to that of conventional butter during storage and induced oxidation. Volatiles were isolated by solvent-assisted flavor evaporation and identified by gas chromatography-olfactometry and mass spectrometry. Aroma extract dilution analysis revealed 18 odorants that were quantified by stable isotope dilution analysis. Another important odorant, 3-methyl-1H-indole (mothball-like odor), was quantified by high-performance liquid chromatography. After storage, UFA/CLA-enriched butter showed higher concentrations of pentanal (fatty), heptanal (green), butanoic acid (cheesy), and delta-decalactone (peach-like). Photo-oxidation of butter samples induced increases in heptanal, (E)-2-octenal, and trans-4,5-epoxy-(E)-2-decenal, especially in conventional butter. The higher vitamin content in UFA/CLA samples may protect this butter from oxidation.

76 FR 59247 - Environmental Impact Considerations, Food Additives, and Generally Recognized As Safe Substances...

Federal Register 2010, 2011, 2012, 2013, 2014

2011-09-26

..., II, IV-B 212 [deg]F, 30 min emulsion of high or low fat. 2. Aqueous, high or low free III, IV-A, VII....... do 120 [deg]F, 30 min oil or fat. \\1\\ Heptane extractant not to be used on wax-lined containers. \\2..., 2011. Susan Bernard, Acting Director, Office of Regulations, Policy and Social Sciences, Center for...

2-[Anilino(phen­yl)meth­yl]cyclo­heptan­one

PubMed Central

Eftekhari-Sis, Bagher; Mohajer, Sahar; Zirak, Maryam; Mozaffarnia, Sakineh; Büyükgüngör, Orhan

2013-01-01

In the title compound, C20H23NO, the cyclo­hepta­none ring adopts a twist-chair conformation, with the amino­methyl substituent in an equatorial position. The relative configuration of the two stereocenters is R,R. In the crystal, mol­ecules are linked by N—H⋯O hydrogen bonds into chains along [100]. PMID:23476371

Microemulsion characterization by the use of a noninvasive backscatter fiber optic probe

NASA Technical Reports Server (NTRS)

Ansari, Rafat R.; Dhadwal, Harbans S.; Cheung, H. M.; Meyer, William V.

1993-01-01

This paper demonstrates the utility of a noninvasive backscatter fiber optic probe for dynamic light-scattering characterization of a microemulsion comprising sodium dodecyl sulfate/1-butanol/ brine/heptane. The fiber probe, comprising two optical fibers precisely positioned in a stainless steel body, is a miniaturized and efficient self-beating dynamic light-scattering system. Accuracy of particle size estimation is better than +/- 2 percent.

Pro-static Agents in Jet Fuels

DTIC Science & Technology

1976-08-16

1000 10,000 CHARGE DENSITY (juC/ms) Fig. 5- Effect otpolar compounds on charging tendency of silica-gel-treated n-heptane Naphthenic acid is neither a...Eastmant Naphthenic acids Practical Eastman t 30 NRL REPORT 8021 Compound Purity Supplier Pararosandine hydrochloride Not available Eastmant...silica gel to remove moisture and polar contaminants that might interfere with the compound or additive being screened. This treatment Manuscript

Reaction bonded silicon nitride prepared from wet attrition-milled silicon. [fractography

NASA Technical Reports Server (NTRS)

Herball, T. P.; Glasgow, T. K.; Shaw, N. J.

1980-01-01

Silicon powder wet milled in heptane was dried, compacted into test bar shape, helium-sintered, and then reaction bonded in nitrogen-4 volume percent hydrogen. As-nitrided bend strengths averaged approximately 290 MPa at both room temperature and 1400 C. Fracture initiation appeared to be associated with subsurface flaws in high strength specimens and both subsurface and surface flaws in low strength specimens.

Reaction bonded silicon nitride prepared from wet attrition-milled silicon

NASA Technical Reports Server (NTRS)

Herbell, T. P.; Glasgow, T. K.; Shaw, N. J.

1980-01-01

Silicon powder wet milled in heptane was dried, compacted into test bar shape, helium-sintered, and then reaction bonded in nitrogen-4 vol% hydrogen. As-nitrided bend strengths averaged approximately 290 MPa at both room temperature and 1400 C. Fracture initiation appeared to be associated with subsurface flaws in high-strength specimens and both subsurface and surface flaws in low-strength specimens.

Simulation of circularly polarized luminescence spectra using coupled cluster theory

NASA Astrophysics Data System (ADS)

McAlexander, Harley R.; Crawford, T. Daniel

2015-04-01

We report the first computations of circularly polarized luminescence (CPL) rotatory strengths at the equation-of-motion coupled cluster singles and doubles (EOM-CCSD) level of theory. Using a test set of eight chiral ketones, we compare both dipole and rotatory strengths for absorption (electronic circular dichroism) and emission to the results from time-dependent density-functional theory (TD-DFT) and available experimental data for both valence and Rydberg transitions. For two of the compounds, we obtained optimized geometries of the lowest several excited states using both EOM-CCSD and TD-DFT and determined that structures and EOM-CCSD transition properties obtained with each structure were sufficiently similar that TD-DFT optimizations were acceptable for the remaining test cases. Agreement between EOM-CCSD and the Becke three-parameter exchange function and Lee-Yang-Parr correlation functional (B3LYP) corrected using the Coulomb attenuating method (CAM-B3LYP) is typically good for most of the transitions, though agreement with the uncorrected B3LYP functional is significantly worse for all reported properties. The choice of length vs. velocity representation of the electric dipole operator has little impact on the EOM-CCSD transition strengths for nearly all of the states we examined. For a pair of closely related β, γ-enones, (1R)-7-methylenebicyclo[2.2.1]heptan-2-one and (1S)-2-methylenebicyclo[2.2.1]heptan-7-one, we find that EOM-CCSD and CAM-B3LYP agree with the energetic ordering of the two possible excited-state conformations, resulting in good agreement with experimental rotatory strengths in both absorption and emission, whereas B3LYP yields a qualitatively incorrect result for the CPL signal of (1S)-2-methylenebicyclo[2.2.1]heptan-7-one. Finally, we predict that one of the compounds considered here, trans-bicyclo[3.3.0]octane-3,7-dione, is unique in that it exhibits an achiral ground state and a chiral first excited state, leading to a strong CPL signal but a weak circular dichroism signal.

Simulation of circularly polarized luminescence spectra using coupled cluster theory

DOE Office of Scientific and Technical Information (OSTI.GOV)

McAlexander, Harley R.; Crawford, T. Daniel, E-mail: crawdad@vt.edu

2015-04-21

We report the first computations of circularly polarized luminescence (CPL) rotatory strengths at the equation-of-motion coupled cluster singles and doubles (EOM-CCSD) level of theory. Using a test set of eight chiral ketones, we compare both dipole and rotatory strengths for absorption (electronic circular dichroism) and emission to the results from time-dependent density-functional theory (TD-DFT) and available experimental data for both valence and Rydberg transitions. For two of the compounds, we obtained optimized geometries of the lowest several excited states using both EOM-CCSD and TD-DFT and determined that structures and EOM-CCSD transition properties obtained with each structure were sufficiently similar thatmore » TD-DFT optimizations were acceptable for the remaining test cases. Agreement between EOM-CCSD and the Becke three-parameter exchange function and Lee-Yang-Parr correlation functional (B3LYP) corrected using the Coulomb attenuating method (CAM-B3LYP) is typically good for most of the transitions, though agreement with the uncorrected B3LYP functional is significantly worse for all reported properties. The choice of length vs. velocity representation of the electric dipole operator has little impact on the EOM-CCSD transition strengths for nearly all of the states we examined. For a pair of closely related β, γ-enones, (1R)-7-methylenebicyclo[2.2.1]heptan-2-one and (1S)-2-methylenebicyclo[2.2.1]heptan-7-one, we find that EOM-CCSD and CAM-B3LYP agree with the energetic ordering of the two possible excited-state conformations, resulting in good agreement with experimental rotatory strengths in both absorption and emission, whereas B3LYP yields a qualitatively incorrect result for the CPL signal of (1S)-2-methylenebicyclo[2.2.1]heptan-7-one. Finally, we predict that one of the compounds considered here, trans-bicyclo[3.3.0]octane-3,7-dione, is unique in that it exhibits an achiral ground state and a chiral first excited state, leading to a strong CPL signal but a weak circular dichroism signal.« less

Dynamic mechanical thermal properties of the dental light-cured nanohybrid composite Kalore, GC: effect of various food/oral simulating liquids.

PubMed

Sideridou, Irini D; Vouvoudi, Evangelia C; Adamidou, Evanthia A

2015-02-01

The aim of this work is the study of the dynamic mechanical thermal properties (viscoelastic properties) of a current dental commercial light-cured nanohybrid resin composite, Kalore, GC (GC Corporation, Tokyo, Japan) along with the study of the effect of some food/oral simulating liquids (FSLs) on these properties. Dynamic mechanical thermal analysis (DMTA) tests were performed on a Diamond Dynamic Mechanical Thermal Analyzer in bending mode. A frequency of 1Hz and a temperature range of 25-185°C were applied, while the heating rate of 2°C/min was selected to cover mouth temperature and the material's likely Tg. The properties were determined after storage in air, distilled water, heptane, ethanol/water solution (75% v/v) or absolute ethanol at 37°C for up to 1h, 1, 7 or 30 days. Storage modulus, loss modulus and tangent delta (tanδ) were plotted against temperature. The glass transition temperatures are taken from the peak of the tangent tanδ versus temperature curves. Moreover, some factors indicating the heterogeneity of the polymer matrix, such as the width (ΔT) at the half of tanδ peak and the "ζ" parameter were determined. All samples analyzed after storage for 1h or 1 day in the aging media showed two Tg values. All samples analyzed after storage for 7 or 30 days in the ageing media showed a unique Tg value. Storage of Kalore GC in dry air, water or heptane at 37°C for 7 days caused post-curing reactions. Storage in air or water for 30 days did not seem to cause further effects. Storage in heptane for 30 days may cause plasticization and probably some degradation of the filler-silane bond and polymer matrix. Storage in ethanol/water solution (75% v/v) or ethanol for 7 days seems to cause post-curing reactions and degradation reactions of the matrix-filler bonds. Storage in ethanol for 30 days caused a strong change of the sample morphology and the DMTA results were not reliable. Copyright © 2014 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Stereocontrolled synthesis of polyhydroxylated bicyclic azetidines as a new class of iminosugars.

PubMed

Malinowski, Maciej; Hensienne, Raphaël; Kern, Nicolas; Tardieu, Damien; Bodlenner, Anne; Hazelard, Damien; Compain, Philippe

2018-06-12

We report herein the development of a stereodivergent route towards polyhydroxylated bicyclic azetidine scaffolds, namely 6-azabicyclo[3.2.0]heptane derivatives. The strategy hinges on a common bicyclic β-lactam precursor, which is forged by way of a rare example of a cationic Dieckmann-type reaction, followed by IBX-mediated desaturation. Substrate-controlled diastereoselective oxidations then allow the divergent preparation of novel iminosugar mimics.

Burning Heptane Droplets on STS-94

NASA Technical Reports Server (NTRS)

2003-01-01

Fuel ignites and burns in the Droplet Combustion Experiment (DCE) on STS-94 on July 11, 1997. This round of experiments burned heptane droplets in 1/2 atmosphere pressure consisting of oxygen and helium. During this mission, scientists have seen for the first time droplets which stop burning due to heat loss by radiation. From these data, the investigators hope to understand the physical and chemical processes that take place in droplet combustion in different environments, including conditions under which the flames extinguish, the chemistry of the combustion reaction, and the production of pollutants such as nitrogen oxides and soot particles. The DCE was designed to investigate the fundamental combustion aspects of single, isolated droplets under different pressures and ambient oxygen concentrations for a range of droplet sizes varying between 2 and 5 mm. The DCE principal investigator was Forman Williams, University of California, San Diego. The experiment was part of the space research investigations conducted during the Microgravity Science Laboratory-1R mission (STS-94, July 1-17 1997). Advanced combustion experiments will be a part of investigations plarned for the International Space Station.(983KB, 9-second MPEG, screen 320 x 240 pixels; downlinked video, higher quality not available) A still JPG composite of this movie is available at http://mix.msfc.nasa.gov/ABSTRACTS/MSFC-0300172.html.

Water-stable helical structure of tertiary amides of bicyclic β-amino acid bearing 7-azabicyclo[2.2.1]heptane. Full control of amide cis-trans equilibrium by bridgehead substitution.

PubMed

Hosoya, Masahiro; Otani, Yuko; Kawahata, Masatoshi; Yamaguchi, Kentaro; Ohwada, Tomohiko

2010-10-27

Helical structures of oligomers of non-natural β-amino acids are significantly stabilized by intramolecular hydrogen bonding between main-chain amide moieties in many cases, but the structures are generally susceptible to the environment; that is, helices may unfold in protic solvents such as water. For the generation of non-hydrogen-bonded ordered structures of amides (tertiary amides in most cases), control of cis-trans isomerization is crucial, even though there is only a small sterical difference with respect to cis and trans orientations. We have established methods for synthesis of conformationally constrained β-proline mimics, that is, bridgehead-substituted 7-azabicyclo[2.2.1]heptane-2-endo-carboxylic acids. Our crystallographic, 1D- and 2D-NMR, and CD spectroscopic studies in solution revealed that a bridgehead methoxymethyl substituent completely biased the cis-trans equilibrium to the cis-amide structure along the main chain, and helical structures based on the cis-amide linkage were generated independently of the number of residues, from the minimalist dimer through the tetramer, hexamer, and up to the octamer, and irrespective of the solvent (e.g., water, alcohol, halogenated solvents, and cyclohexane). Generality of the control of the amide equilibrium by bridgehead substitution was also examined.

Microgravity Droplet Combustion in CO2 Enriched Environments at Elevated Pressures

NASA Technical Reports Server (NTRS)

Hicks, Michael C.; Nayagam, V.; Williams, F. A.

2007-01-01

Microgravity droplet combustion experiments were performed in elevated concentrations of CO2 at pressures of 1.0 atm, 3.0 atm, and 5.0 atm to examine the effects of a radiatively participating suppression agent in space applications. Methanol and n-heptane droplets, with an initial diameter of 2.0 mm supported on a quartz fiber, were used in these experiments. The ambient O2 concentration was held constant at 21% and the CO2 concentrations ranged from 0% to a maximum of 70%, by volume with the balance consisting of N2 . Results from the methanol tests showed slight decreases in burning rates with increased CO2 concentrations at all ambient pressures. The n-heptane tests show slight increases in burning rates with increasing CO2 concentrations at each pressure level. Instantaneous radiative heat flux was also measured using both a broadband radiometer (i.e., wavelengths from 0.6 microns to 40.0 microns) and a narrowband radiometer (i.e., centered at 5.6 microns with a filter width at half maximum of 1.5 microns). Radiative exchanges between the droplet and surrounding gases as well as the soot field produce departures from the classical quasisteady theory which would predict a decrease in burning rates with increasing CO2 concentrations in microgravity.

Models for liquid-liquid partition in the system dimethyl sulfoxide-organic solvent and their use for estimating descriptors for organic compounds.

PubMed

Karunasekara, Thushara; Poole, Colin F

2011-07-15

Partition coefficients for varied compounds were determined for the organic solvent-dimethyl sulfoxide biphasic partition system where the organic solvent is n-heptane or isopentyl ether. These partition coefficient databases are analyzed using the solvation parameter model facilitating a quantitative comparison of the dimethyl sulfoxide-based partition systems with other totally organic partition systems. Dimethyl sulfoxide is a moderately cohesive solvent, reasonably dipolar/polarizable and strongly hydrogen-bond basic. Although generally considered to be non-hydrogen-bond acidic, analysis of the partition coefficient database strongly supports reclassification as a weak hydrogen-bond acid in agreement with recent literature. The system constants for the n-heptane-dimethyl sulfoxide biphasic system provide an explanation of the mechanism for the selective isolation of polycyclic aromatic compounds from mixtures containing low-polarity hydrocarbons based on the capability of the polar interactions (dipolarity/polarizability and hydrogen-bonding) to overcome the opposing cohesive forces in dimethyl sulfoxide that are absent for the interactions with hydrocarbons of low polarity. In addition, dimethyl sulfoxide-organic solvent systems afford a complementary approach to other totally organic biphasic partition systems for descriptor measurements of compounds virtually insoluble in water. Copyright © 2011 Elsevier B.V. All rights reserved.

Olfaction in the boll weevil,Anthonomus grandis Boh. (Coleoptera: Curculionidae): Electroantennogram studies.

PubMed

Dickens, J C

1984-12-01

Electroantennogram (EAG) techniques were utilized to measure the antennal olfactory responsiveness of adult boll weevils,Anthonomus grandis Boh. (Coleoptera: Curculionidae), to 38 odorants, including both insect and host plant (Gossypium hirsutum L.) volatiles. EAGs of both sexes were indicative of at least two receptor populations: one receptor population primarily responsive to pheromone components and related compounds, the other receptor population primarily responsive to plant odors. Similar responses to male aggregation pheromone components (i.e., compounds I, II, and III + IV) were obtained from both sexes, but females were slightly more sensitive to I. Both sexes were highly responsive to components of the "green leaf volatile complex," especially the six-carbon saturated and monounsaturated primary alcohols. Heptanal was the most active aldehyde tested. More acceptors responded to oxygenated monoterpenes than to monoterpene hydrocarbons. β-Bisabolol, the major volatile of cotton, was the most active sesquiterpene. In general, males, which are responsible for host selection and pheromone production, were more sensitive to plant odors than were females. In fact, males were as sensitive to β-bisabolol and heptanal as to aggregation pheromone components. Electrophysiological data are discussed with regard to the role of insect and host plant volatiles in host selection and aggregation behavior of the boll weevil.

Oxides of Nitrogen Emissions from the Combustion of Monodisperse Liquid Fuel Sprays. Ph.D. Thesis

NASA Technical Reports Server (NTRS)

Sarv, H.

1985-01-01

A study of NO sub x formation in a one dimensional monodisperse spray combustion system, which allowed independent droplet size variation, was conducted. Temperature, NO and NO sub x concentrations were measured in the transition region, encompassing a 26 to 74 micron droplet size range. Emission measurements of hydrocarbons, carbon monoxide, carbon dioxide and oxygen were also made. The equivalence ratio was varied between 0.8 and 1.2 for the fuels used, including methanol, isopropanaol, n-heptane and n-octane. Pyridine and pyrrole were added to n-heptane as nitrogen-containing additives in order to simulate synthetic fuels. Results obtained from the postflame regions using the pure fuels indicate an optimum droplet size in the range of 43 to 58 microns for minimizing NO sub x production. For the fuels examined, the maximum NO sub x reductions relative to the small droplet size limit were about 10 to 20% for lean and 20 to 30% for stoichiometric and rich mixtures. This behavior is attributed to droplet interactions and the transition from diffusive to premixed type of burning. Preflame vaporization controls the gas phase stoichiometry which has a significant effect on the volume of the hot gases surrounding a fuel droplet, where NO sub x is formed.

Polymethylated [Fe(η6-arene)2]2+ dications: methyl-group rearrangements and application of the EINS mechanism.

PubMed

Štíbr, Bohumil; Bakardjiev, Mario; Hájková, Zuzana; Holub, Josef; Padělková, Zdenka; Růžička, Aleš; Kennedy, John D

2011-06-14

Reactions between the methylated arenes ArMe(n) [where ArMe(n) = C(6)Me(n)H((6-n)), and n = 1-6] and FeCl(2) in heptane at 90 °C in the presence of anhydrous AlCl(3) give, for the arenes with n = 1-5, extensive isomerisations and disproportionations involving the methyl groups on the arene rings, and the formation of mixtures of [Fe(ArMe(n))(2)](2+) dications that defy separation into pure species. GC-MS studies of AlCl(3)/mesitylene and AlCl(3)/durene reactions in the absence of FeCl(2) (90 °C, 2 h) allow quantitative assessments of the rearrangements, and the EINS mechanism (electrophile-induced nucleophilic substitution) is applied to rationalise the phenomena. By contrast, ArMe(n) / FeCl(2) /AlCl(3) reactions in heptane for 24-36 h at room-temperature proceed with no rearrangements, allowing the synthesis of the complete series of pure [Fe(ArMen)](2+) cations in yields of 48-71%. The pure compounds are characterised by (1)H NMR spectroscopy and electrospray-ionization mass-spectrometry (ESI-MS), and the structures of [Fe(m-xylene)(2)][PF(6)](2) and [Fe(durene)(2)][PF(6)](2) are established by single-crystal X-ray diffraction analyses.

Stable superhydrophilic coating on superhydrophobic porous media by functionalized nanoparticles

NASA Astrophysics Data System (ADS)

Khazaei, Masoud; Taghi Sadeghi, Mohammad; Sadat Hosseini, Marzieh

2018-01-01

In this study, the hydrophilicity property of TiO2 nano-coating was improved by zinc acetate-assisted sol-gel method. The stable superhydrophilic coating was fabricated on a superhydrophobic mineral rock surface. The wettability of surface before and after coating was characterized by contact angle measurements. The n-heptane and water droplet contact angle was 0° and 168° respectively, so the untreated rock was superhydrophobic. After nano-treatment, the n-heptane and water contact angle changed to 172° and 0° respectively, so the superhydrophilic coating was formed on the superhydrophobic surface. The thermal, mechanical and salinity stability of the fabricated coatings was investigated. The coatings had high thermal and salinity stability; they also had moderate mechanical stability that was evaluated by abrasion test. The morphology and composition of synthesized nanoparticles were characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy and x-ray diffraction (XRD) analyses. Characterization of the coated surfaces was conducted by SEM and XRD analyses. Applications of these nano-coatings include surfaces where cleanliness is paramount such as in hospitals as well as the protection of public monuments and building facades from weathering. Novel industrial application includes wettability alteration of oil wet carbonate rock for enhanced oil recovery.

Application of saponin biosurfactant and its recovery in the MEUF process for removal of methyl violet from wastewater.

PubMed

Samal, Kulbhushan; Das, Chandan; Mohanty, Kaustubha

2017-12-01

The potential of saponin, a biosurfactant, in the micellar enhanced ultrafiltration (MEUF) process was tested systematically for removal of methyl violet from wastewater. For this, the aqueous extract of reetha (Sapindus mukorossi) pericarp which contains saponin was used as the biosurfactant. First, the micellar solubilization of methyl violet in saponin micelles was investigated in terms of molar solubilization power (SP) of saponin. It was observed that the adsorption of methyl violet on the agglomerates of saponin micelles was mainly responsible for the enhanced solubilization. The Gibbs free energy of solubilization (calculated as -29.63 kJ mol -1 ) suggested that process was feasible and spontaneous. The MEUF experiments were performed in batch as well as continuous mode using saponin biosurfactant, and the effect of operating parameters on permeate flux and solute retention were evaluated. The removal of methyl violet in MEUF process was >99% achieved with 10 kDa polyethersulfone (PES) membrane for feed dye concentration of 250 mg L -1 at studied conditions. Finally, the saponin in permeate was recovered using n-heptane and n-butanol by solvent extraction process. The solvent n-butanol showed better extraction efficiency as compared to n-heptane for saponin extraction. Copyright © 2017 Elsevier Ltd. All rights reserved.

VAPOR-PHASE TRANSPORT OF TRICHLOROETHENE IN AN INTERMEDIATE-SCALE VADOSE-ZONE SYSTEM: RETENTION PROCESSES AND TRACER-BASED PREDICTION

PubMed Central

Costanza-Robinson, Molly S.; Carlson, Tyson D.; Brusseau, Mark L.

2013-01-01

Gas-phase miscible-displacement experiments were conducted using a large weighing lysimeter to evaluate retention processes for volatile organic compounds (VOCs) in water-unsaturated (vadoze-zone) systems, and to test the utility of gas-phase tracers for predicting VOC retardation. Trichloroethene (TCE) served as a model VOC, while trichlorofluoromethane (CFM) and heptane were used as partitioning tracers to independently characterize retention by water and the air-water interface, respectively. Retardation factors for TCE ranged between 1.9 and 3.5, depending on water content. The results indicate that dissolution into the bulk water was the primary retention mechanism for TCE under all conditions studied, contributing approximately two thirds of the total measured retention. Accumulation at the air-water interface comprised a significant fraction of the observed retention for all experiments, with an average contribution of approximately 24%. Sorption to the solid phase contributed approximately 10% to retention. Water contents and air-water interfacial areas estimated based on the CFM and heptane tracer data, respectively, were similar to independently measured values. Retardation factors for TCE predicted using the partitioning-tracer data were in reasonable agreement with the measured values. These results suggest that gas-phase tracer tests hold promise for characterizing the retention and transport of VOCs in the vadose-zone. PMID:23333418

Modular and selective biosynthesis of gasoline-range alkanes.

PubMed

Sheppard, Micah J; Kunjapur, Aditya M; Prather, Kristala L J

2016-01-01

Typical renewable liquid fuel alternatives to gasoline are not entirely compatible with current infrastructure. We have engineered Escherichia coli to selectively produce alkanes found in gasoline (propane, butane, pentane, heptane, and nonane) from renewable substrates such as glucose or glycerol. Our modular pathway framework achieves carbon-chain extension by two different mechanisms. A fatty acid synthesis route is used to generate longer chains heptane and nonane, while a more energy efficient alternative, reverse-β-oxidation, is used for synthesis of propane, butane, and pentane. We demonstrate that both upstream (thiolase) and intermediate (thioesterase) reactions can act as control points for chain-length specificity. Specific free fatty acids are subsequently converted to alkanes using a broad-specificity carboxylic acid reductase and a cyanobacterial aldehyde decarbonylase (AD). The selectivity obtained by different module pairings provides a foundation for tuning alkane product distribution for desired fuel properties. Alternate ADs that have greater activity on shorter substrates improve observed alkane titer. However, even in an engineered host strain that significantly reduces endogenous conversion of aldehyde intermediates to alcohol byproducts, AD activity is observed to be limiting for all chain lengths. Given these insights, we discuss guiding principles for pathway selection and potential opportunities for pathway improvement. Copyright © 2015 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

Plasma Assisted Combustion: Flame Regimes and Kinetic Studies

DTIC Science & Technology

2015-01-05

Kinetic model Fuel: Dimethyl ether Oxidizer= (1-x)O2 + xO3, x=0 - 0.1, p=1 atm Ozone chemistry & Dimethyl ether model ...diffusional cool flames • A heated counterflow burner integrated with vaporization system1 • n-heptane/nitrogen vs. oxygen/ ozone • Ozone generator...micro-DBD) produces 2- 5 % of ozone in oxygen stream, depending on oxygen flow rate • Speciation profiles by using a micro-probe sampling with a

Mechanistic analysis of intramolecular free radical reactions toward synthesis of 7-azabicyclo[2.2.1]heptane derivatives.

PubMed

Soriano, Elena; Marco-Contelles, José

2009-06-05

The mechanisms for the formation of conformationally constrained epibatidine analogues by intramolecular free radical processes have been computationally addressed by means of DFT methods. The mechanism and the critical effect of the 7-nitrogen protecting group on the outcome of these radical-mediated cyclizations are discussed. Theoretical findings account for unexpected experimental results and can assist in the selection of proper precursors for a successful cyclization.

Fundamental Flame Velocities of Pure Hydrocarbons I : Alkanes, Alkenes, Alkynes Benzene, and Cyclohexane

NASA Technical Reports Server (NTRS)

Gerstein, Melvin; Levine, Oscar; Wong, Edgar L

1950-01-01

The flame velocities of 37 pure hydrocarbons including normal and branched alkanes, alkenes, and alkynes; as well as benzene and cyclohexane, together with the experimental technique employed are presented. The normal alkanes have about the same flame velocity from ethane through heptane with methane being about 16 percent lower. Unsaturation increases the flame velocity in the order of alkanes, alkenes, and alkynes. Branching reduces the flame velocity.

40 CFR 439.16 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2011 CFR

2011-07-01

...-Heptane 3.0 0.7 n-Hexane 3.0 0.7 Methylene chloride 3.0 0.7 Chloroform 0.1 0.03 1,2-dichloroethane 20.7 8...: Pretreatment Standards (PSES) Regulated parameter Maximum daily 1 Maximum monthly average 1 Ammonia (as N) 2 84.1 29.4 Acetone 20.7 8.2 4-methyl-2-pentanone 20.7 8.2 Isobutyraldehyde 20.7 8.2 n-Amyl acetate 20.7...

The Impact of Low Octane Hydrocarbon Blending Streams on Ethanol Engine Optimization

DOE Office of Scientific and Technical Information (OSTI.GOV)

Szybist, James P; West, Brian H

2013-01-01

Ethanol is a very attractive fuel from an end-use perspective because it has a high chemical octane number and a high latent heat of vaporization. When an engine is optimized to take advantage of these fuel properties, both efficiency and power can be increased through higher compression ratio, direct fuel injection, higher levels of boost, and a reduced need for enrichment to mitigate knock or protect the engine and aftertreatment system from overheating. The ASTM D5798 specification for high level ethanol blends, commonly called E85, underwent a major revision in 2011. The minimum ethanol content was revised downward from 68more » vol% to 51 vol%, which combined with the use of low octane blending streams such as natural gasoline introduces the possibility of a lower octane E85 fuel. While this fuel is suitable for current ethanol tolerant flex fuel vehicles, this study experimentally examines whether engines can still be aggressively optimized for the resultant fuel from the revised ASTM D5798 specification. The performance of six ethanol fuel blends, ranging from 51-85% ethanol, is compared to a premium-grade certification gasoline (UTG-96) in a single-cylinder direct-injection (DI) engine with a compression ratio of 12.9:1 at knock-prone engine conditions. UTG-96 (RON = 96.1), light straight run gasoline (RON = 63.6), and n-heptane (RON = 0) are used as the hydrocarbon blending streams for the ethanol-containing fuels in an effort to establish a broad range of knock resistance for high ethanol fuels. Results show that nearly all ethanol-containing fuels are more resistant to engine knock than UTG-96 (the only exception being the ethanol blend with 49% n-heptane). This knock resistance allows ethanol blends made with 33 and 49% light straight run gasoline, and 33% n-heptane to be operated at significantly more advanced combustion phasing for higher efficiency, as well as at higher engine loads. While experimental results show that the octane number of the hydrocarbon blend stock does impact engine performance, there remains a significant opportunity for engine optimization when considering even the lowest octane fuels that are in compliance with the current revision of ASTM D5798 compared to premium-grade gasoline.« less

Problems in Catalytic Oxidation of Hydrocarbons and Detailed Simulation of Combustion Processes

NASA Astrophysics Data System (ADS)

Xin, Yuxuan

This dissertation research consists of two parts, with Part I on the kinetics of catalytic oxidation of hydrocarbons and Part II on aspects on the detailed simulation of combustion processes. In Part I, the catalytic oxidation of C1--C3 hydrocarbons, namely methane, ethane, propane and ethylene, was investigated for lean hydrocarbon-air mixtures over an unsupported Pd-based catalyst, from 600 to 800 K and under atmospheric pressure. In Chapter 2, the experimental facility of wire microcalorimetry and simulation configuration were described in details. In Chapter 3 and 4, the oxidation rate of C1--C 3 hydrocarbons is demonstrated to be determined by the dissociative adsorption of hydrocarbons. A detailed surface kinetics model is proposed with deriving the rate coefficient of hydrocarbon dissociative adsorption from the wire microcalorimetry data. In Part II, four fundamental studies were conducted through detailed combustion simulations. In Chapter 5, self-accelerating hydrogen-air flames are studied via two-dimensional detailed numerical simulation (DNS). The increase in the global flame velocity is shown to be caused by the increase of flame surface area, and the fractal structure of the flame front is demonstrated by the box-counting method. In Chapter 6, skeletal reaction models for butane combustion are derived by using directed relation graph (DRG) and DRG-aided sensitivity analysis (DRGASA), and uncertainty minimization by polynomial chaos expansion (MUM-PCE) mothodes. The dependence of model uncertainty is subjected to the completeness of the model. In Chapter 7, a systematic strategy is proposed to reduce the cost of the multicomponent diffusion model by accurately accounting for the species whose diffusivity is important to the global responses of the combustion systems, and approximating those of less importance by the mixture-averaged model. The reduced model is validated in an n-heptane mechanism with 88 species. In Chapter 8, the influence of Soret diffusion on the n-heptane/air flames is investigated numerically. In the unstretched flames, Soret diffusion primarily affects the chemical kinetics embedded in the flame structure and the net effect is small; while in the stretched flames, its impact is mainly through those of n-heptane and the secondary fuel, H2, in modifying the flame temperature, with substantial effects.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Johnson, Grant E.; Moser, Trevor; Engelhard, Mark

About 40 years ago, it was shown that tungsten carbide exhibits similar catalytic behavior to Pt for certain commercially relevant reactions, thereby suggesting the possibility of cheaper and earth-abundant substitutes for costly and rare precious metal catalysts. In this work, reactive magnetron sputtering of Ta in the presence of three model hydrocarbons (2-butanol, heptane, and m-xylene) combined with gas aggregation and ion soft landing was employed to prepare organic-inorganic hybrid nanoparticles (NPs) on surfaces for evaluation of catalytic activity and durability. The electro-catalytic behavior of the NPs supported on glassy carbon was evaluated in acidic aqueous solution by cyclic voltammetry.more » The Ta-heptane and Ta-xylene NPs were revealed to be active and robust toward promotion of the oxygen reduction reaction, an important process occurring at the cathode in fuel cells. In comparison, pure Ta and Ta-butanol NPs were essentially unreactive. Characterization techniques including atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) were applied to probe how different sputtering conditions such as the flow rates of gases, sputtering current, and aggregation length affect the properties of the NPs. AFM images reveal the focused size of the NPs as well as their preferential binding along the step edges of graphite surfaces. In comparison, TEM images of the same NPs on carbon grids show that they bind randomly to the surface with some agglomeration but little coalescence. The TEM images also reveal morphologies with crystalline cores surrounded by amorphous regions for NPs formed in the presence of 2-butanol and heptane. In contrast, NPs formed in the presence of m-xylene are amorphous throughout. XPS spectra indicate that while the percentage of Ta, C, and O in the NPs varies depending on the sputtering conditions and hydrocarbon employed, the electron binding energies of the elements are similar for all of the NPs. The difference in reactivity between the NPs is attributed to their Ta/C ratios. Collectively, the findings presented herein indicate that reactive magnetron sputtering and gas aggregation combined with ion soft landing offer a promising physical approach for the synthesis of organic-inorganic hybrid NPs that have potential as low-cost durable substitutes for precious metals in catalysis« less

Fabrication of electrocatalytic Ta nanoparticles by reactive sputtering and ion soft landing.

PubMed

Johnson, Grant E; Moser, Trevor; Engelhard, Mark; Browning, Nigel D; Laskin, Julia

2016-11-07

About 40 years ago, it was shown that tungsten carbide exhibits similar catalytic behavior to Pt for certain commercially relevant reactions, thereby suggesting the possibility of cheaper and earth-abundant substitutes for costly and rare precious metal catalysts. In this work, reactive magnetron sputtering of Ta in the presence of three model hydrocarbons (2-butanol, heptane, and m-xylene) combined with gas aggregation and ion soft landing was employed to prepare organic-inorganic hybrid nanoparticles (NPs) on surfaces for evaluation of catalytic activity and durability. The electrocatalytic behavior of the NPs supported on glassy carbon was evaluated in acidic aqueous solution by cyclic voltammetry. The Ta-heptane and Ta-xylene NPs were revealed to be active and robust toward promotion of the oxygen reduction reaction, an important process occurring at the cathode in fuel cells. In comparison, pure Ta and Ta-butanol NPs were essentially unreactive. Characterization techniques including atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and transmission electron microscopy (TEM) were applied to probe how different sputtering conditions such as the flow rates of gases, sputtering current, and aggregation length affect the properties of the NPs. AFM images reveal the focused size of the NPs as well as their preferential binding along the step edges of graphite surfaces. In comparison, TEM images of the same NPs on carbon grids show that they bind randomly to the surface with some agglomeration but little coalescence. The TEM images also reveal morphologies with crystalline cores surrounded by amorphous regions for NPs formed in the presence of 2-butanol and heptane. In contrast, NPs formed in the presence of m-xylene are amorphous throughout. XPS spectra indicate that while the percentage of Ta, C, and O in the NPs varies depending on the sputtering conditions and hydrocarbon employed, the electron binding energies of the elements are similar for all of the NPs. The difference in reactivity between the NPs is attributed to their Ta/C ratios. Collectively, the findings presented herein indicate that reactive magnetron sputtering and gas aggregation combined with ion soft landing offer a promising physical approach for the synthesis of organic-inorganic hybrid NPs that have potential as low-cost durable substitutes for precious metals in catalysis.

Structural and diffusion characterizations of steam-stable mesostructured zeolitic UL-ZSM-5 materials.

PubMed

Vinh-Thang, Hoang; Huang, Qinglin; Ungureanu, Adrian; Eić, Mladen; Trong-On, Do; Kaliaguine, Serge

2006-05-09

A series of mesoporous UL-ZSM-5 materials (Si/Al = 50) with different micro- and mesoporosity as well as crystallinity was prepared following the procedure proposed in one of our recent studies (Trong-On, D.; Kaliaguine, S. Angew. Chem. Int. Ed. 2001, 40, 3248-3251. Trong-On, D.; Kaliaguine, S. U.S. Patent 6,669,924, B1, 2003). These materials have zeolitic structure in the form of nanoparticles intergrown in the walls of the amorphous wormhole-like aluminosilicate mesopores of Al-Meso-50, which was used as a precursor in the synthesis. The structure, crystallinity, and textural properties of the synthesized materials, as well as a reference ZSM-5 zeolite sample, were determined by X-ray diffraction (XRD), transmission electron microscopy (TEM)/scanning electron microscoy (SEM) analyses, Fourier transform infrared spectroscopy (FTIR), 27Al magic angle spinning (MAS) nuclear magnetic resonance (NMR), and nitrogen adsorption/desorption techniques. The acid properties were examined by FTIR of adsorbed pyridine. UL-ZSM-5 materials were shown to be highly hydrothermally stable. The diffusion of two C7 hydrocarbons, i.e., n-heptane and toluene, in four UL-ZSM-5 materials with different microporosities, related acidities, and crystallinities were investigated using the zero-length column (ZLC) method. Furthermore, the wormhole-like mesostructured aluminosilicate precursor (Al-Meso-50) and a reference MFI zeolite sample were also investigated using the same technique. A theoretical model considering a combination of mesopore diffusion (with surface slip in the main channels) with an activated, mainly surface diffusion mechanism in the intrawall biporous structure, was proposed and employed to interpret the experimental ZLC results. A classical Knudsen type of diffusion was replaced by an activated surface slip type of diffusion mechanism in the mesopores. The transport of n-heptane in UL-ZSM-5 materials was found to be mainly controlled by mesopore diffusion in the main-channel structure, while that of toluene was dominated by the intrawall diffusion process. Diffusion activation energies of n-heptane are about 2 times higher in comparison to toluene, which has a larger kinetic diameter. The main mesopore channel structure seems to appreciably contribute to the overall mass transport. Furthermore, the effect of hydrothermal treatment (20% steam at 800 degrees C for 24 h) on the diffusion of these two sorbates on UL-ZSM-5 materials was also evaluated.

High-Density Renewable Fuels Based on the Selective Dimerization of Pinenes

DTIC Science & Technology

2009-01-01

spectrometry (GC/MS), revealing that the principal reaction was isomerization to a mixture of camphene, limonene , and R-pinene, with some β-pinene...ratio of R-pinene/ camphene/β-pinene/ limonene was roughly 3:5:2:4. Heating the mixture to the reflux temperature of heptane led to a vigorous...important product is p-cymene, which is derived from limonene . Pre- vious studies suggest that the mechanism for formation of p-cymene proceeds

Efficient High-Pressure State Equations

NASA Technical Reports Server (NTRS)

Harstad, Kenneth G.; Miller, Richard S.; Bellan, Josette

1997-01-01

A method is presented for a relatively accurate, noniterative, computationally efficient calculation of high-pressure fluid-mixture equations of state, especially targeted to gas turbines and rocket engines. Pressures above I bar and temperatures above 100 K are addressed The method is based on curve fitting an effective reference state relative to departure functions formed using the Peng-Robinson cubic state equation Fit parameters for H2, O2, N2, propane, methane, n-heptane, and methanol are given.

Comparison of Sampling Probe and Thermal Desorber in Hazardous Air Pollutants on Site (HAPSITE) Extended Range (ER) for Analysis of Toxic Organic (TO)-15 Compounds

DTIC Science & Technology

2014-03-01

641,000 671,667 1,4‐dioxane  88  2.20 101 154,000 160,000 137,000 150,333 105,000  119,000 113,000 112,333 Trichloroethylene   130  2.20 87 412,000...Bromodichloromethane 14-dioxane Trichloroethylene Heptane (Z)-13-Dichloro-1-propene Methyl Isobutyl Ketone (E)-13-Dichloro-1-propene 112

Photophysics of 4-dimethylamino-4'-cyanostilbene and 4-azetidinyl-4'-cyanostilbene. Time-resolved fluorescence and trans-cis photoisomerisation

NASA Astrophysics Data System (ADS)

Il'ichev, Yurii V.; Kühnle, Wolfgang; Zachariasse, Klaas A.

1996-11-01

The fluorescence decays of trans-4-dimethylamino-4'-cyanostilbene (DCS) and trans-4-azetidinyl-4'-cyanostilbene (ACS) in an unpolar (n-heptane) and a polar (acetonitrile) solvent are single exponential down to a time resolution of around 5 ps and dual fluorescence is not observed. The dipole moment increases in two steps: from 7 D in the ground state via 13 D (DCS) or 10 D (ACS) for the Franck-Condon excited state to 21 D (DCS) or 22 D (ACS) for the relaxed fluorescing CT state. This means that the intramolecular charge transfer (ICT) in the excited state at most involves an intermediate with a subpicosecond lifetime. The presence of the azetidinyl group in ACS does not slow down the ICT reaction, contrary to what has been found for the 4-aminobenzonitriles, showing that inversion of the amino group is not an important reaction coordinate here. The activation energy Etc for trans-cis photoisomerisation is determined from the fluorescence decays in n-heptane (14.0 kJ/mol, DCS) and in acetonitrile (22.7 kJ/mol, DCS and 22.5 kJ/mol, ACS). This increase of Etc with solvent polarity, opposite to what has been found for trans-stilbene, shows that the photoisomerisation transition state is less polar than the CT state.

Isolation and purification of series bioactive components from Hypericum perforatum L. by counter-current chromatography.

PubMed

Cao, Xueli; Wang, Qiaoe; Li, Yan; Bai, Ge; Ren, Hong; Xu, Chunming; Ito, Yoichiro

2011-03-01

Counter-current chromatography (CCC) combined with pre-separation by ultrasonic solvent extraction was successively used for the separation of series bioactive compounds from the crude extract of Hypericum perforatum L. The petroleum ether extract was separated by the solvent system of n-heptane-methanol-acetonitrile (1.5:0.5:0.5, v/v) and n-heptane-methanol (1.5:1, v/v) in gradient elution, yielding a phloroglucinol compound, hyperforin with HPLC purity over 98%. The ethyl acetate extract was separated by using the solvent system composed of hexane-ethyl acetate-methanol-water (1:1:1:1 and 1:3:1:3, v/v) in gradient through both reverse phase and normal phase elution mode, yielding a naphthodianthrone compound, hypericin with HPLC purity about 95%. The n-butanol extract was separated with the solvent system composed of n-butanol-ethyl acetate-water (1:4:5 and 1.5:3.5:5, v/v) in elution and back-extrusion mode, yielding two of flavones, rutin and hyperoside, with HPLC purity over 95%. HPLC-MS, reference sample and UV spectrum were selectively used in separation to search for target compounds from HPLC-DAD profiles of different sub-extracts. The structures of isolated compounds were further identified by ESI-MS, ¹HNMR and ¹³CNMR. Copyright © 2011 Elsevier B.V. All rights reserved.

Vapor-phase transport of trichloroethene in an intermediate-scale vadose-zone system: retention processes and tracer-based prediction.

PubMed

Costanza-Robinson, Molly S; Carlson, Tyson D; Brusseau, Mark L

2013-02-01

Gas-phase transport experiments were conducted using a large weighing lysimeter to evaluate retention processes for volatile organic compounds (VOCs) in water-unsaturated (vadose-zone) systems, and to test the utility of gas-phase tracers for predicting VOC retardation. Trichloroethene (TCE) served as a model VOC, while trichlorofluoromethane (CFM) and heptane were used as partitioning tracers to independently characterize retention by water and the air-water interface, respectively. Retardation factors for TCE ranged between 1.9 and 3.5, depending on water content. The results indicate that dissolution into the bulk water was the primary retention mechanism for TCE under all conditions studied, contributing approximately two-thirds of the total measured retention. Accumulation at the air-water interface comprised a significant fraction of the observed retention for all experiments, with an average contribution of approximately 24%. Sorption to the solid phase contributed approximately 10% to retention. Water contents and air-water interfacial areas estimated based on the CFM and heptane tracer data, respectively, were similar to independently measured values. Retardation factors for TCE predicted using the partitioning-tracer data were in reasonable agreement with the measured values. These results suggest that gas-phase tracer tests hold promise for characterizing the retention and transport of VOCs in the vadose-zone. Copyright © 2012 Elsevier B.V. All rights reserved.

The BUME method: a new rapid and simple chloroform-free method for total lipid extraction of animal tissue

NASA Astrophysics Data System (ADS)

Löfgren, Lars; Forsberg, Gun-Britt; Ståhlman, Marcus

2016-06-01

In this study we present a simple and rapid method for tissue lipid extraction. Snap-frozen tissue (15-150 mg) is collected in 2 ml homogenization tubes. 500 μl BUME mixture (butanol:methanol [3:1]) is added and automated homogenization of up to 24 frozen samples at a time in less than 60 seconds is performed, followed by a 5-minute single-phase extraction. After the addition of 500 μl heptane:ethyl acetate (3:1) and 500 μl 1% acetic acid a 5-minute two-phase extraction is performed. Lipids are recovered from the upper phase by automated liquid handling using a standard 96-tip robot. A second two-phase extraction is performed using 500 μl heptane:ethyl acetate (3:1). Validation of the method showed that the extraction recoveries for the investigated lipids, which included sterols, glycerolipids, glycerophospholipids and sphingolipids were similar or better than for the Folch method. We also applied the method for lipid extraction of liver and heart and compared the lipid species profiles with profiles generated after Folch and MTBE extraction. We conclude that the BUME method is superior to the Folch method in terms of simplicity, through-put, automation, solvent consumption, economy, health and environment yet delivering lipid recoveries fully comparable to or better than the Folch method.

Isolation and purification of series bioactive components from Hypericum Perforatum L. by high-speed counter-current chromatography

PubMed Central

Cao, Xueli; Wang, Qiaoe; Li, Yan; Bai, Ge; Ren, Hong; Ito, Yiochiro

2011-01-01

High-speed counter-current chromatography (HSCCC) combined with pre-separation by ultrasonic solvent extraction was successively used for the separation of series bioactive compounds from the crude extract of Hypericum perforatum L. The petroleum ether extract was separated by the solvent system of n-heptane-methanol-acetonitrile (1.5:0.5:0.5, v/v) and n-heptane-methanol (1.5:1, v/v) in gradient elution, yielding a phloroglucinol compound, hyperforin with HPLC purity over 98%. The ethyl acetate extract was separated by using the solvent system composed of hexane-ethyl acetate-methanol-water (1:1:1:1 and 1:3:1:3, v/v) in gradient through both reverse phase and normal phase elution mode, yielding a naphthodianthrone compound, hypericin with HPLC purity about 95%. The n-butanol extract was separated with the solvent system composed of n-butanol-ethyl acetate–water (1:4:5 and 1.5:3.5:5, v/v) in elution and back-extrusion mode, yielding two of flavones, rutin and hyperoside, with HPLC purity over 95%. HPLC-MS, reference sample and UV spectrum were selectively used in separation to search for target compounds from HPLC-DAD profiles of different sub-extracts. The structures of isolated compounds were further identified by ESI-MS, 1HNMR and 13CNMR. PMID:21306961

Robust fabrication of thin film polyamide-TiO2 nanocomposite membranes with enhanced thermal stability and anti-biofouling propensity.

PubMed

Khorshidi, Behnam; Biswas, Ishita; Ghosh, Tanushree; Thundat, Thomas; Sadrzadeh, Mohtada

2018-01-15

The development of nano-enabled composite materials has led to a paradigm shift in the manufacture of high-performance nanocomposite membranes with enhanced permeation, thermo-mechanical, and antibacterial properties. The major challenges to the successful incorporation of nanoparticles (NPs) to polymer films are the severe aggregation of the NPs and the weak compatibility of NPs with polymers. These two phenomena lead to the formation of non-selective voids at the interface of the polymer and NPs, which adversely affect the separation performance of the membrane. To overcome these challenges, we have developed a new method for the fabrication of robust TFN reverse osmosis membranes. This approach relies on the simultaneous synthesis and surface functionalization of TiO 2 NPs in an organic solvent (heptane) via biphasic solvothermal reaction. The resulting stable suspension of the TiO 2 NPs in heptane was then utilized in the interfacial (in-situ) polymerization reaction where the NPs were entrapped within the matrix of the polyamide (PA) membrane. TiO 2 NPs of 10 nm were effectively incorporated into the thin PA layer and improved the thermal stability and anti-biofouling properties of the resulting TFN membranes. These features make our synthesized membranes potential candidates for applications where the treatment of high-temperature streams containing biomaterials is desirable.

Tests of biocompatibility of alpha-tocopherol with respect to the use as a stabilizer in ultrahigh molecular weight polyethylene for articulating surfaces in joint endoprostheses.

PubMed

Wolf, C; Lederer, K; Müller, U

2002-07-01

To inhibit the oxidation in vivo of hip-cups made of ultrahigh molecular weight polyethylene (UHMW-PE), the natural antioxidant alpha-tocopherol was added to the polymer. The added alpha-tocopherol may however undergo chemical transformations during manufacturing and sterilization by gamma-irradiation of hip-cups which may differ from human metabolism. Therefore, the question of the biocompatibility of the respective transformation products was investigated on test samples, which were prepared under the same conditions as applied for the production and sterilization of hip-cups. Thin plates (25 x 18 x 2 mm(3)) were fabricated out of test samples to investigate the cytotoxic activity according to EN 30993-5. In cytotoxicity testing, proliferation, mitochondrial activity and membrane integrity were not influenced by the material. In contrast, cell adhesion and cell spreading were diminished as shown with hemalum staining. In order to investigate the genotoxicity, the alpha-tocopherol and its transformation products were extracted from test specimens by n-heptane at 185 degrees C under nitrogen atmosphere. Then the n-heptane was evaporated in vacuo and the remaining alpha-tocopherol and its transformation products were dissolved in DMSO. The genotoxicity of this extract was then tested by the Ames-test according to DIN UA 12 (1995), which showed no indication for genotoxic activity.

Exploring the chemical kinetics of partially oxidized intermediates by combining experiments, theory, and kinetic modeling.

PubMed

Hoyermann, Karlheinz; Mauß, Fabian; Olzmann, Matthias; Welz, Oliver; Zeuch, Thomas

2017-07-19

Partially oxidized intermediates play a central role in combustion and atmospheric chemistry. In this perspective, we focus on the chemical kinetics of alkoxy radicals, peroxy radicals, and Criegee intermediates, which are key species in both combustion and atmospheric environments. These reactive intermediates feature a broad spectrum of chemical diversity. Their reactivity is central to our understanding of how volatile organic compounds are degraded in the atmosphere and converted into secondary organic aerosol. Moreover, they sensitively determine ignition timing in internal combustion engines. The intention of this perspective article is to provide the reader with information about the general mechanisms of reactions initiated by addition of atomic and molecular oxygen to alkyl radicals and ozone to alkenes. We will focus on critical branching points in the subsequent reaction mechanisms and discuss them from a consistent point of view. As a first example of our integrated approach, we will show how experiment, theory, and kinetic modeling have been successfully combined in the first infrared detection of Criegee intermediates during the gas phase ozonolysis. As a second example, we will examine the ignition timing of n-heptane/air mixtures at low and intermediate temperatures. Here, we present a reduced, fuel size independent kinetic model of the complex chemistry initiated by peroxy radicals that has been successfully applied to simulate standard n-heptane combustion experiments.

Fiber-Supported Droplet Combustion. Experiment 32

NASA Technical Reports Server (NTRS)

Dietrich, Daniel L.; Haggard, John B., Jr.; Nayagam, Vedha; Dryer, Frederick L.; Williams, Forman A.; Shaw, Ben D.

1998-01-01

Individual droplets with diameters ranging from about 2 mm to 5 mm were burned under microgravity conditions in air at 1 bar with an ambient temperature of 300 K. Each droplet was tethered by a silicon carbide fiber of 80 mm or 150 mm diameter to keep it in view of video recording, and, in some tests, a forced air flow was applied in a direction parallel to the fiber axis. Methanol, two methanol-water mixtures, two methanol-dodecanol mixtures, and two heptane-hexadecane mixtures were the fuels. Droplet diameters were measured as functions of time and compared with existing theoretical predictions. The prediction that methanol droplets extinguish at diameters that increase with increasing initial droplet diameter is verified by these experiments. In addition, the quasi-steady burning rate constant of the heptane-hexadecane mixtures appears to decrease with increasing droplet diameter; obscuration consistent with very heavy sooting, but without the formation of soot shells, is observed for the largest of these droplets. Forced convective flow around methanol droplets was found to increase the burning rate and to produce a ratio of downstream-to-upstream flame radius that remained constant as the droplet size decreased, a trend in agreement with earlier results obtained at higher convective velocities for smaller droplets having larger flame standoff ratios. There are a number of implications of the experimental results regarding droplet-combustion theory.

Experiments And Model Development For The Investigation Of Sooting And Radiation Effects In Microgravity Droplet Combustion

NASA Technical Reports Server (NTRS)

Yozgatligil, Ahmet; Choi, Mun Young; Dryer, Frederick L.; Kazakov, Andrei; Dobashi, Ritsu

2003-01-01

This study involves flight experiments (for droplets between 1.5 to 5 mm) and supportive ground-based experiments, with concurrent numerical model development and validation. The experiments involve two fuels: n-heptane, and ethanol. The diagnostic measurements include light extinction for soot volume fraction, two-wavelength pyrometry and thin-filament pyrometry for temperature, spectral detection for OH chemiluminescence, broadband radiometry for flame emission, and thermophoretic sampling with subsequent transmission electron microscopy for soot aerosol property calculations.

Ignition Delays of Alkyl Thiophosphites with White and Red Fuming Nitric Acids Within Temperature Range 80 to -105 F

NASA Technical Reports Server (NTRS)

Miller, Riley O; Ladanyi, Dezso J

1953-01-01

Ignition delays of alkyl thiophosphites were obtained in a modified open-cup apparatus and a small-scale rocket engine apparatus. At -40 F, mixed alkyl thiophosphites gave short delays with white fuming nitric acid containing 2 percent water and red fuming nitric acids of widely varying compositions. At -40 F and higher, triethyl trithiophosphite blended with as much as 40 percent n-heptane gave satisfactory self-igniting properties at temperatures as low as -76 F.

Formation of fatty acids in photochemical conversions of saturated hydrocarbons

NASA Technical Reports Server (NTRS)

Telegina, T. A.; Pavlovskaya, T. Y.; Ladyzhenskaya, A. I.

1977-01-01

Abiogenic synthesis of fatty acids was studied in photochemical conversions of saturated hydrocarbons. It was shown that, in a hydrocarbon water CaCO3 suspension, the action of 254 nm UV rays caused the formation of fatty acids with a maximum number of carbon atoms in the chain not exceeding that in the initial hydrocarbon. Synthesis of acetic, propionic, butyric, valeric, caproic, enanthic and caprylic (in the case of octane) acids occurs in heptane water CaCO3 and octane water CaCO3 systems.

A Randomized Clinical Trial of Allopregnanolone for the Treatment of Severe Traumatic Brain Injury

DTIC Science & Technology

2015-12-01

at 30-40 psi of hydrogen with a dry 10% palladium on carbon catalyst. The yield was almost quantitative and less than 1% of byproducts were formed...to fully dissolve the material and heptane was added to precipitate allopregnanolone. After isolation and drying , a 59.2% recovery was obtained...for 66 hours and 28 minutes, and was deemed 1% dry by thermogravimetric analysis. The product was reslurried for 6 hours and 15 minutes, washed with

40 CFR 439.16 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2014 CFR

2014-07-01

... Xylenes 3.0 0.7 n-Heptane 3.0 0.7 n-Hexane 3.0 0.7 Methylene chloride 3.0 0.7 Chloroform 0.1 0.03 1,2... 1 Ammonia (as N) 2 84.1 29.4 Acetone 20.7 8.2 4-methyl-2-pentanone 20.7 8.2 Isobutyraldehyde 20.7 8.2 n-Amyl acetate 20.7 8.2 n-Butyl acetate 20.7 8.2 Ethyl acetate 20.7 8.2 Isopropyl acetate 20.7 8.2...

40 CFR 439.16 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2013 CFR

2013-07-01

... Xylenes 3.0 0.7 n-Heptane 3.0 0.7 n-Hexane 3.0 0.7 Methylene chloride 3.0 0.7 Chloroform 0.1 0.03 1,2... 1 Ammonia (as N) 2 84.1 29.4 Acetone 20.7 8.2 4-methyl-2-pentanone 20.7 8.2 Isobutyraldehyde 20.7 8.2 n-Amyl acetate 20.7 8.2 n-Butyl acetate 20.7 8.2 Ethyl acetate 20.7 8.2 Isopropyl acetate 20.7 8.2...

40 CFR 439.16 - Pretreatment standards for existing sources (PSES).

Code of Federal Regulations, 2012 CFR

2012-07-01

... Xylenes 3.0 0.7 n-Heptane 3.0 0.7 n-Hexane 3.0 0.7 Methylene chloride 3.0 0.7 Chloroform 0.1 0.03 1,2... 1 Ammonia (as N) 2 84.1 29.4 Acetone 20.7 8.2 4-methyl-2-pentanone 20.7 8.2 Isobutyraldehyde 20.7 8.2 n-Amyl acetate 20.7 8.2 n-Butyl acetate 20.7 8.2 Ethyl acetate 20.7 8.2 Isopropyl acetate 20.7 8.2...

Some Recent Observations on the Burning of Isolated N-Heptane and Alcohol Droplets

NASA Technical Reports Server (NTRS)

Dryer, F. L.

1999-01-01

In a joint program involving Prof F.A. Williams of the University of California, San Diego and Dr. Vedha Nayagam of the National Center for Microgravity Research on Fluid and Combustion, the combustion of liquid fuel droplets having initial diameters between about 1 mm and 6 mm is being studied. The objectives of the work are to improve fundamental knowledge of droplet combustion dynamics through microgravity experiments and theoretical analyses. The Princeton contributions to the collaborative program supports the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies through experiments and numerical modeling. The complementary UCSD contributions apply asymptotic theoretical analyses and are described in the published literature and in a companion communication in this volume. Emphases of the Princeton work are on the study of simple alcohols (methanol, ethanol), alcohol/water mixtures, and pure alkanes (n-heptane, n-decane) as fuels, with time dependent measurements of drop size, flame-stand-off, liquid-phase composition, and finally, extinction. Ground based experiments have included bench-scale studies at Princeton and collaborative experimental studies in the 2.2 and 5.18 second drop towers at NASA-Glenn Research Center. Spacelab studies have included fiber-supported droplet combustion (FSDC) experiments in the Glovebox facility with accompanying numerical analyses. Experiments include FSDC-1, performed on the USML-2 mission in October, 1995 (STS-73) and FSDC-2, on the second flight of the MSL-1 mission in July, 1997 (STS-94).

Development of solvent systems with room temperature ionic liquids for the countercurrent chromatographic separation of very nonpolar lipid compounds.

PubMed

Müller, Marco; Englert, Michael; Earle, Martyn J; Vetter, Walter

2017-03-10

Solvent systems are not readily available for the separation of very nonpolar compounds by countercurrent chromatography (CCC). In this study we therefore evaluated the suitability of room temperature ionic liquids (IL) in organic solvents for the CCC separation of the extremely nonpolar lipid compounds tripalmitin (PPP) and cholesteryl stearate (CS). The four IL tested were [C 10 mim][OTf], [C 2 mim][NTf 2 ], [P66614][NTf 2 ], and [P66614][Cl]. Search for a CCC-suited solvent system started with solubility studies with fourteen organic solvents. Following this, combinations were made with one organic solvent miscible and one organic solvent immiscible with IL (147 combinations). Twenty-four initially monophasic mixtures of two organic solvents became biphasic by adding IL. Several unexpected results could be observed. For instance, n-hexane and n-heptane became biphasic with [P66614][Cl]. Further nine systems became biphasic although the IL was not miscible in any of the two components. These 33 solvent systems were investigated with regard to phase ratio, settling time, share of IL in the upper phase and last not least the K U/L values of PPP and CS, which were 8.1 and 7.7 respectively. The most promising system, n-heptane/chloroform/[C 10 mim][OTf] (3:3:1, v/v/v) allowed a partial separation of PPP and CS by CCC which was not achieved beforehand. Copyright © 2017 Elsevier B.V. All rights reserved.

Limonene ozonolysis in the presence of nitric oxide: Gas-phase reaction products and yields

NASA Astrophysics Data System (ADS)

Ham, Jason E.; Harrison, Joel C.; Jackson, Stephen R.; Wells, J. R.

2016-05-01

The reaction products from limonene ozonolysis were investigated using the new carbonyl derivatization agent, O-tert-butylhydroxylamine hydrochloride (TBOX). With ozone (O3) as the limiting reagent, five carbonyl compounds were detected. The yields of the carbonyl compounds are discussed with and without the presence of a hydroxyl radical (OHrad) scavenger, giving insight into the influence secondary OH radicals have on limonene ozonolysis products. The observed reaction product yields for limonaketone (LimaKet), 7-hydroxyl-6-oxo-3-(prop-1-en-2-yl)heptanal (7H6O), and 2-acetyl-5-oxohexanal (2A5O) were unchanged suggesting OHrad generated by the limonene + O3 reaction does not contribute to their formation. The molar yields of 3-isopropenyl-6-oxo-heptanal (IPOH) and 3-acetyl-6-oxoheptanal (3A6O) decreased by 68% and >95%; respectively, when OHrad was removed. This suggests that OHrad radicals significantly impact the formation of these products. Nitric oxide (NO) did not significantly affect the molar yields of limonaketone or IPOH. However, NO (20 ppb) considerably decreased the molar reaction product yields of 7H6O (62%), 2A5O (63%), and 3A6O (47%), suggesting NO reacted with peroxyl intermediates, generated during limonene ozonolysis, to form other carbonyls (not detected) or organic nitrates. These studies give insight into the transformation of limonene and its reaction products that can lead to indoor exposures.

Experimental and modeling study of fuel interactions with an alkyl nitrate cetane enhancer, 2-ethyl-hexyl nitrate

DOE PAGES

Goldsborough, S. S.; Johnson, M. V.; Banyon, C.; ...

2014-07-15

Our study investigates the autoignition behavior of two gasoline surrogates doped with an alkyl nitrate cetane enhancer, 2-ethyl-hexyl nitrate (2EHN) to better understand dopant interactions with the fuels, including influences of accelerating kinetic pathways and enhanced exothermicity. A primary reference fuel (PRF) blend of n-heptane/iso-octane, and a toluene reference fuel (TRF) blend of n-heptane/iso-octane/toluene are used where the aromatic fraction of the latter is set to 20% (liquid volume), while the content of n-heptane is adjusted so that the overall reactivity of the undoped fuels is similar, e.g., Anti-Knock Index (AKI) of similar to 91, Cetane Number (CN) similar tomore » 25. Doping levels of 0.1, 1.0 and 3.0% (liquid volume basis) are used where tests are conducted within a rapid compression machine (RCM) at a compressed pressure of 21 bar, covering temperatures from 675 to 1025 K with stoichiometric fuel-oxygen ratios at O-2 = 11.4%. At the experimental conditions, it is found that the doping effectiveness of 2EHN is fairly similar between the two fuels, though 2EHN is more effective in the aromatic blend at the lowest temperatures, while it is slightly more effective in the non-aromatic blend at intermediate temperatures. Furthermore, kinetic modeling of the experiments indicates that although some of the reactivity trends can be captured using a detailed model, the extents of predicted Cetane Number enhancement by 2EHN are too large, while differences in fuel interactions for the two fuels result in excessive stimulation of the non-aromatic blend. Sensitivity analysis using the kinetic model indicates that the CH 2O and CH 3O 2 chemistry are very sensitive to the dopant at all conditions. The rate of 2EHN decomposition is only important at low temperatures where its decomposition rate is slow due to the high activation energy of the reaction. At higher temperatures, dopant-derived 3-heptyl radicals are predicted to play an important role stimulating ignition. Finally, nitrogen chemistry is important through the 'NO - NO 2 loop' where this can generate substantial amounts of OH. But, at the highest doping levels the formation of methyl and ethyl nitrite, and nitric acid significantly competes with this so that less OH is generated and this constrains the reactivity enhancement of 2EHN.« less

Modeling Joint Effects of Mixtures of Chemicals on Microorganisms Using Quantitative Structure Activity Relationships

DTIC Science & Technology

1993-08-22

Cyclohexane Alk 74 133 26 Pentane Alk 70 150 27 Hexane Alk 38 47 28 Heptane Alk 18 58 29 Octane Alk 8 60 30 Bis (2-chloroethyl) ether Alc 1,600 3,025 31...Triethanolarnine Amni 900 741 SAro- aromatic; Hal- balogemmaed aliphatic; Alk - alkanes; Alc- alcohols, este’s, ketones and et Aji- amineL -5- Correlation...chemicals using laboratory grown activated sludge by synthetic feed. They adapted the OECD Method 209, using inhibition of oxygen uptake rate as the measure

Activation of hydrocarbons and the octane number

NASA Technical Reports Server (NTRS)

Peschard, Marcel

1939-01-01

This report presents an examination of the history of research on engine knocking and the various types of fuels used in the investigations of this phenomenon. According to this report, the spontaneous ignition of hydrocarbons doped with oxygen follows the logarithmic law within a certain temperature range, but not above 920 degrees K. Having extended the scope of investigations to prove hydrocarbons, the curves of the mixtures burned by air should then be established by progressive replacement of pure iso-octane with heptane. Pentane was also examined in this report.

Testing of Fire Fighting Foam.

DTIC Science & Technology

1980-11-01

for Fresh and Sea Water ( MIL - F - 24385 ); -(C) Underwriters Laboratories Inc. S andard for Air Foam Equipment and Liquid Con- centrates (UL162);4D...C. Test Facilities 6 D. Test Procedures 7 III. Results of Tests A. FRN-1007 33 B. MIL - F - 24385 34 C. UL 162 34 D. O- F -555C 35 E. Foam Quality 35 IV...1 gpm) H N-heptane in. inch (25.4 mm = 1 in.) ipm liters per minute M Motor Octane Rating MIL MIL - F - 24385 Test Method NFPA National Fire Protection

Long period grating refractive-index sensor: optimal design for single wavelength interrogation.

PubMed

Kapoor, Amita; Sharma, Enakshi K

2009-11-01

We report the design criteria for the use of long period gratings (LPGs) as refractive-index sensors with output power at a single interrogating wavelength as the measurement parameter. The design gives maximum sensitivity in a given refractive-index range when the interrogating wavelength is fixed. Use of the design criteria is illustrated by the design of refractive-index sensors for specific application to refractive-index variation of a sugar solution with a concentration and detection of mole fraction of xylene in heptane (paraffin).

Spontaneous ignition characteristics of gaseous hydrocarbon-air mixtures

NASA Technical Reports Server (NTRS)

Freeman, G.; Lefebvre, A. H.

1984-01-01

Experiments are conducted to determine the spontaneous ignition delay times of gaseous propane, kerosine vapor, and n-heptane vapor in mixtures with air, and oxygen-enriched air, at atmospheric pressure. Over a range of equivalence ratios from 0.2 to 0.8 it is found that ignition delay times are sensibly independent of fuel concentration. However, the results indicate a strong dependence of delay times on oxygen concentration. The experimental data for kerosine and propane demonstrate very close agreement with the results obtained previously by Mullins and Lezberg respectively.

The role of water in the formation of reversed micelles: An antimicellization agent

USGS Publications Warehouse

Yu, Z.-J.; Zhou, N.-F.; Neuman, R.D.

1992-01-01

Micellization of sodium bis(2-ethylhexyl) phosphate in n-heptane has been studied under controlled environmental conditions by dynamic and static light scattering. The results clearly show that a trace amount of water has a very dramatic effect on reversed micellization. In contrast with results in the literature, water can function as an antimicellization agent. The generality of and the evidence for supporting the current view that water is a prerequisite for the formation of reversed micelles are discussed and criticized. ?? 1992 American Chemical Society.

CHARGE-TRANSFER ASSOCIATION AND PARAMAGNETISM OF SOME ORGANIC SYSTEMS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Eastman, J W

When p-xylene was combined with chloranil in n-heptane, charge-transfer optical absorption was observed. The magnitude of this absorption was used to calculate an equilibrium constant for the formation of a donor-acceptor complex containing one p-xylene was combined with carbon tetrabromide and with carbon tetrachloride in n-heptane, no charge-transfer absorption was observed. Reactions of N,N,N',N'-tetramethyl-p-phenylenediamine (TMPD) with chloranil (pQCl/ sub 4/) were observed in ethylene dichloride and acetonitrile. In both solvents adduct formation occurred initially, as observed by its charge-transfer absorption. In acetonitrile time-dependent electron spin resonance (ESR) absorption was observed, and it was identified with the positive and negative radicalmore » ions of TMPD and pQCl/sub 4/, respectively. In this case a completely ionized electron transfer had occurred. Chloranil and other quinones were found to react with N,N-dimethylaniline forming a crystal violet salt. The diamagnetic donor-acceptor complexes and also semiquinone radicals are intermediates which were observed. Some physical measurements of the kinetics of this reaction are described and correlated. When fluoranil was allowed to react with dimethylaniline, the hyperfine splitting by the fluorine atoms of the fluoranil radical was not resolved. Characteristics of the ESR absorption by this radical in dimethylaniline are discussed in terms of an electron transfer between the semiquinone and quinone, and between the semiquinone and hydroquinone ion. Paramagnetism was discovered in hydrocarbon-quinone solids. ESR absorption was assigned to imperfections in the solid which was normally diamagnetic. The preparation of these solids and some of their physical characteristics are described. (auth)« less

A computational investigation of diesel and biodiesel combustion and NOx formation in a light-duty compression ignition engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Zihan; Srinivasan, Kalyan K.; Krishnan, Sundar R.

Diesel and biodiesel combustion in a multi-cylinder light duty diesel engine were simulated during a closed cycle (from IVC to EVO), using a commercial computational fluid dynamics (CFD) code, CONVERGE, coupled with detailed chemical kinetics. The computational domain was constructed based on engine geometry and compression ratio measurements. A skeletal n-heptane-based diesel mechanism developed by researchers at Chalmers University of Technology and a reduced biodiesel mechanism derived and validated by Luo and co-workers were applied to model the combustion chemistry. The biodiesel mechanism contains 89 species and 364 reactions and uses methyl decanoate, methyl-9- decenoate, and n-heptane as the surrogatemore » fuel mixture. The Kelvin-Helmholtz and Rayleigh-Taylor (KH-RT) spray breakup model for diesel and biodiesel was calibrated to account for the differences in physical properties of the fuels which result in variations in atomization and spray development characteristics. The simulations were able to capture the experimentally observed pressure and apparent heat release rate trends for both the fuels over a range of engine loads (BMEPs from 2.5 to 10 bar) and fuel injection timings (from 0° BTDC to 10° BTDC), thus validating the overall modeling approach as well as the chemical kinetic models of diesel and biodiesel surrogates. Moreover, quantitative NOx predictions for diesel combustion and qualitative NOx predictions for biodiesel combustion were obtained with the CFD simulations and the in-cylinder temperature trends were correlated to the NOx trends.« less

Procedure for and results of simultaneous determination of aromatic hydrocarbons and fatty acid methyl esters in diesel fuels by high performance liquid chromatography.

PubMed

Kamiński, M; Gilgenast, E; Przyjazny, A; Romanik, G

2006-07-28

The content of aromatic hydrocarbons in diesel fuels is regulated by appropriate standards, and a further reduction in the allowed concentration of these hazardous substances in these fuels is expected. The content of aromatic hydrocarbons in diesel fuels is most often determined using standard methods EN-12916 or ASTM D-6591. The content of polycyclic aromatic hydrocarbons (PAHs) is determined from a single peak obtained using normal phase high-performance liquid chromatography (NP-HPLC), a column of the NH2 type, n-heptane as the eluent, refractive index detector (RID) and backflushing of the eluent. However, the methods mentioned above cannot be applied when the fuel contains fatty acid methyl esters (FAME), which lately has become more common. The content of FAME in diesel oils is determined using mid-IR spectrophotometry based on the absorption of carbonyl group. However, no standard procedure for the determination of classes of aromatic hydrocarbons in diesel fuels containing FAME is yet available. The present work describes such a modification of methods EN-12916/ASTM D-6591 that provides a simultaneous determination of individual groups of aromatic hydrocarbons, total content of polycyclic aromatic hydrocarbons and the FAME content in diesel fuels. The refractive index detector (RID) and n-heptane as the mobile phase are still used, but backflushing of the eluent is applied after the elution of all polycyclic aromatic hydrocarbons. Additionally, ultraviolet diode array detection is used for the exact determination of low contents of polycyclic aromatic hydrocarbons and to confirm the presence of FAME in the analyzed fuel.

Synthesis and characterization of oleic acid surface modified magnetic iron oxide nanoparticles by using biocompatible w/o microemulsion for heavy metal removal

NASA Astrophysics Data System (ADS)

Rose, Laili Che; Suhaimi, Hamdan; Mamat, Mazidah; Lik, Thang Zhe

2017-09-01

Oleic acid modified magnetic iron oxide nanoparticles (OA-MIONs) was prepared for removal of Cu2+ ion from aqueous solution. OA-MIONs was prepared by W/O microemulsion template which composed of mixed non-ionic surfactants and 1-hexanol as emulsifier. The effect of weight ratio of the constituent of microemulsion template on the physical and chemical properties of OA-MIONs was studied by characterization using Fourier transform infrared (FT-IR), scanning electron microscopy (SEM) and X-ray powder diffraction (XRD) analysis. FT-IR spectra showed that all templates shared similar chemical structure with slight difference in the peak intensity. Scanning electron micrograph illustrated that the OA-MIONs synthesized via template with the lowest weight ratio of emulsifier to heptane had a more regular spherical shape and was well-distributed. XRD had confirmed that the identity of synthesized OA-MIONs was Fe3O4. Based on the characterization result, the template with lowest weight ratio of emulsifier to heptane was chosen for the heavy metal adsorption study. The adsorption capacity OA-MIONs as a function of pH, contact time and adsorbent dosage were studied. The adsorption process reached equilibrium for 90 minutes and successfully adsorbed 43% of Cu2+ ion from aqueous solution. The adsorption behavior was well described by Langmuir isotherm. The maximum adsorption capacity was determined and found to be 555.56 mg/g. The value of Langmuir equilibrium parameter, RL was found between 0 and 1, suggested that a favorable monolayer adsorption process had taken out.

Dynamic analysis of bulk-fill composites: Effect of food-simulating liquids.

PubMed

Eweis, Ahmed Hesham; Yap, Adrian U-Jin; Yahya, Noor Azlin

2017-10-01

This study investigated the effect of food simulating liquids on visco-elastic properties of bulk-fill restoratives using dynamic mechanical analysis. One conventional composite (Filtek Z350 [FZ]), two bulk-fill composites (Filtek Bulk-fill [FB] and Tetric N Ceram [TN]) and a bulk-fill giomer (Beautifil-Bulk Restorative [BB]) were evaluated. Specimens (12 × 2 × 2mm) were fabricated using customized stainless steel molds. The specimens were light-cured, removed from their molds, finished, measured and randomly divided into six groups. The groups (n = 10) were conditioned in the following mediums for 7 days at 37°C: air (control), artificial saliva (SAGF), distilled water, 0.02N citric acid, heptane, 50% ethanol-water solution. Specimens were assessed using dynamic mechanical testing in flexural three-point bending mode and their respective mediums at 37°C and a frequency range of 0.1-10Hz. The distance between the supports were fixed at 10mm and an axial load of 5N was employed. Data for elastic modulus, viscous modulus and loss tangent were subjected to ANOVA/Tukey's tests at significance level p < 0.05. Significant differences in visco-elastic properties were observed between materials and mediums. Apart from bulk-fill giomer, elastic modulus was the highest after conditioning in heptane. No apparent trends were noted for viscous modulus. Generally, loss tangent was the highest after conditioning in ethanol. The effect of food-simulating liquids on the visco-elastic properties of bulk-fill composites was material and medium dependent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Transition of carbon nanostructures in heptane diffusion flames

NASA Astrophysics Data System (ADS)

Hu, Wei-Chieh; Hou, Shuhn-Shyurng; Lin, Ta-Hui

2017-02-01

The flame synthesis has high potential in industrial production of carbon nanostructure (CNS). Unfortunately, the complexity of combustion chemistry leads to less controlling of synthesized products. In order to improve the understanding of the relation between flames and CNSs synthesized within, experiments were conducted through heptane flames in a stagnation-point liquid-pool system. The operating parameters for the synthesis include oxygen supply, sampling position, and sampling time. Two kinds of nanostructures were observed, carbon nanotube (CNT) and carbon nano-onion (CNO). CNTs were synthesized in a weaker flame near extinction. CNOs were synthesized in a more sooty flame. The average diameter of CNTs formed at oxygen concentration of 15% was in the range of 20-30 nm. For oxygen concentration of 17%, the average diameter of CNTs ranged from 24 to 27 nm, while that of CNOs was around 28 nm. For oxygen concentration of 19%, the average diameter of CNOs produced at the sampling position 0.5 mm below the flame front was about 57 nm, while the average diameters of CNOs formed at the sampling positions 1-2.5 mm below the flame front were in the range of 20-25 nm. A transition from CNT to CNO was observed by variation of sampling position in a flame. We found that the morphology of CNS is directly affected by the presence of soot layer due to the carbonaceous environment and the growth mechanisms of CNT and CNO. The sampling time can alter the yield of CNSs depending on the temperature of sampling position, but the morphology of products is not affected.

Bottom-up coarse-grained models that accurately describe the structure, pressure, and compressibility of molecular liquids

DOE Office of Scientific and Technical Information (OSTI.GOV)

Dunn, Nicholas J. H.; Noid, W. G., E-mail: wnoid@chem.psu.edu

2015-12-28

The present work investigates the capability of bottom-up coarse-graining (CG) methods for accurately modeling both structural and thermodynamic properties of all-atom (AA) models for molecular liquids. In particular, we consider 1, 2, and 3-site CG models for heptane, as well as 1 and 3-site CG models for toluene. For each model, we employ the multiscale coarse-graining method to determine interaction potentials that optimally approximate the configuration dependence of the many-body potential of mean force (PMF). We employ a previously developed “pressure-matching” variational principle to determine a volume-dependent contribution to the potential, U{sub V}(V), that approximates the volume-dependence of the PMF.more » We demonstrate that the resulting CG models describe AA density fluctuations with qualitative, but not quantitative, accuracy. Accordingly, we develop a self-consistent approach for further optimizing U{sub V}, such that the CG models accurately reproduce the equilibrium density, compressibility, and average pressure of the AA models, although the CG models still significantly underestimate the atomic pressure fluctuations. Additionally, by comparing this array of models that accurately describe the structure and thermodynamic pressure of heptane and toluene at a range of different resolutions, we investigate the impact of bottom-up coarse-graining upon thermodynamic properties. In particular, we demonstrate that U{sub V} accounts for the reduced cohesion in the CG models. Finally, we observe that bottom-up coarse-graining introduces subtle correlations between the resolution, the cohesive energy density, and the “simplicity” of the model.« less

Chemoenzymatic synthesis and cannabinoid activity of a new diazabicyclic amide of phenylacetylricinoleic acid.

PubMed

López-Ortíz, Manuel; Herrera-Solís, Andrea; Luviano-Jardón, Axel; Reyes-Prieto, Nidia; Castillo, Ivan; Monsalvo, Ivan; Demare, Patricia; Méndez-Díaz, Mónica; Regla, Ignacio; Prospéro-García, Oscar

2010-06-01

Endocannabinoids (eCBs) are endogenous neuromodulators of synaptic transmission. Their dysfunction may cause debilitating disorders of diverse clinical manifestation. For example, drug addiction, lack of sex desire, eating disorders, such as anorexia or bulimia and dyssomnias. eCBs also participate in the regulation of core temperature and pain perception. In this context, it is important to recognize the utility of cannabinoid receptor 1 (CB1R) agonists, natural as Delta(9)-tetrahydrocannabinol (THC) or synthetic as Nabilone as useful drugs to alleviate this kind of patients' suffering. Therefore, we have developed a new drug, (R,Z)-18-((1S,4S)-5-methyl-2,5-diazabicyclo[2.2.1]heptan-2-yl)-18-oxooctadec-9-en-7-yl phenylacetate (PhAR-DBH-Me), that appears to bind and activate the CB1R. This diazabicyclic amide was synthesized from phenylacetylricinoleic acid and (1S,4S)-2,5-diazabicyclo[2.2.1]heptane. To test its cannabinergic properties we evaluated its effects on core temperature, pain perception, and the sleep-waking cycle of rats. Results indicate that 20 and 40mg/kg of PhAR-DBH-Me readily reduced core temperature and increased pain perception threshold. In addition, 20mg/kg increased REM sleep in otherwise normal rats. All these effects were prevented or attenuated by AM251, a CB1R antagonist. Place preference conditioning studies indicated that this molecule does not produce rewarding effects. These results strongly support that PhAR-DBH-Me possesses cannabinoid activity without the reinforcement effects. Copyright 2010 Elsevier Ltd. All rights reserved.

Aloe vera extract activity on human corneal cells.

PubMed

Woźniak, Anna; Paduch, Roman

2012-02-01

Ocular diseases are currently an important problem in modern societies. Patients suffer from various ophthalmologic ailments namely, conjunctivitis, dry eye, dacryocystitis or degenerative diseases. Therefore, there is a need to introduce new treatment methods, including medicinal plants usage. Aloe vera [Aloe barbadensis Miller (Liliaceae)] possesses wound-healing properties and shows immunomodulatory, anti-inflammatory or antioxidant activities. NR uptake, MTT, DPPH• reduction, Griess reaction, ELISA and rhodamine-phalloidin staining were used to test toxicity, antiproliferative activity, reactive oxygen species (ROS) reduction, nitric oxide (NO) and cytokine level, and distribution of F-actin in cells, respectively. The present study analyzes the effect of Aloe vera extracts obtained with different solvents on in vitro culture of human 10.014 pRSV-T corneal cells. We found no toxicity of ethanol, ethyl acetate and heptane extracts of Aloe vera on human corneal cells. No ROS reducing activity by heptane extract and trace action by ethanol (only at high concentration 125 µg/ml) extract of Aloe vera was observed. Only ethyl acetate extract expressed distinct free radical scavenging effect. Plant extracts decreased NO production by human corneal cells as compared to untreated controls. The cytokine (IL-1β, IL-6, TNF-α and IL-10) production decreased after the addition of Aloe vera extracts to the culture media. Aloe vera contains multiple pharmacologically active substances which are capable of modulating cellular phenotypes and functions. Aloe vera ethanol and ethyl acetate extracts may be used in eye drops to treat inflammations and other ailments of external parts of the eye such as the cornea.

Effect of New Antiviral Agent Camphecin on Behavior of Mice.

PubMed

Babina, A V; Lavrinenko, V A; Yarovaya, O I; Salakhutdinov, N F

2017-01-01

We studied the effect of camphecin (1,7,7-trimethylbicyclo[2.2.1]heptan-2-ylidene-aminoethanol) on mouse behavior in the open-field test. Camphecin possesses antiviral activity and inhibits viral replication, but its influence on the nervous system is poorly studied. Single camphecin injection produced no significant changes in behavioral patterns. Chronic camphecin administration (5 times over 2 weeks) to mice of different strains had no significant influence on open field behavior (motor, exploratory activity, anxiety, emotional state and vegetative functions). The findings are discussed in the context of neutral influence of camphecin on animal behavior.

Method for recovering light hydrocarbons from coal agglomerates

DOEpatents

Huettenhain, Horst; Benz, August D.; Getsoian, John

1991-01-01

A method and apparatus for removing light hydrocarbons, such as heptane, from coal agglomerates includes an enclosed chamber having a substantially horizontal perforate surface therein. The coal agglomerates are introduced into a water bath within the chamber. The agglomerates are advanced over the surface while steam is substantially continuously introduced through the surface into the water bath. Steam heats the water and causes volatilization of the light hydrocarbons, which may be collected from the overhead of the chamber. The resulting agglomerates may be collected at the opposite end from the surface and subjected to final draining processes prior to transportation or use.

Flame Speeds and Energy Considerations for Explosions in a Spherical Bomb

NASA Technical Reports Server (NTRS)

Fiock, Ernest F; Marvin, Charles F , Jr; Caldwell, Frank R; Roeder, Carl H

1940-01-01

Simultaneous measurements were made of the speed of flame and the rise in pressure during explosions of mixtures of carbon monoxide, normal heptane, iso-octane, and benzene in a 10-inch spherical bomb with central ignition. From these records, fundamental properties of the explosive mixtures, which are independent of the apparatus, were computed. The transformation velocity, or speed at which flame advances into and transforms the explosive mixture, increases with both the temperature and the pressure of the unburned gas. The rise in pressure was correlated with the mass of charge inflamed to show the course of the energy developed.

Reactivity and Selectivity in Hydrovinylation of Strained Alkenes

PubMed Central

Liu, Wang; RajanBabu, T. V.

2010-01-01

Scope of Ni(II)-catalyzed hydrovinylation has been extended to strained alkenes such as heterobicyclic- [2.2.1]heptanes and cylobutenes. Reactions involving the heterobicyclic compounds are rare examples for this class of compounds where the metal-catalyzed C-C bond-forming reactions proceed without a concomitant ring-opening process. While the enantioselectivity in these systems remains modest, hydrovinylation of endo-5,6--bis-benzyloxymethylbicyclo[2.2.1]hept-2-ene gives excellent yield (>90%) of the product with one of the highest enantioselectivities (95–99 %ee) reported for a C-C bondforming reaction of norbornenes. PMID:20964350

Frequency response of a vaporization process to distorted acoustic disturbances

NASA Technical Reports Server (NTRS)

Heidmann, M. F.

1972-01-01

The open-loop response properties expressed as the mass vaporized in phase and out of phase with the pressure oscillations were numerically evaluated for a vaporizing n-heptane droplet. The evaluation includes the frequency dependence introduced by periodic oscillation in droplet mass and temperature. A given response was achieved over a much broader range of frequency with harmonically distorted disturbances than with sinusoidal disturbances. The results infer that distortion increases the probability of incurring spontaneous and triggered instability in any rocket engine combustor by broadening the frequency range over which the vaporization process can support an instability.

Fatty acid ethyl ester concentrations in hair and self-reported alcohol consumption in 644 cases from different origin.

PubMed

Süsse, Silke; Selavka, Carl M; Mieczkowski, Tom; Pragst, Fritz

2010-03-20

For diagnosis of chronic alcohol abuse, fatty acid ethyl esters (FAEE) were determined in hair samples from 644 individuals, mainly parents from child protection cases. The analysis for ethyl myristate, ethyl palmitate, ethyl oleate and ethyl stearate was performed according to a validated procedure consisting of external degreasing by two times washing with n-heptane, extraction with a mixture of dimethylsulfoxide and n-heptane, separation and evaporation of the n-heptane layer, headspace solid phase microextraction of the residue after addition of phosphate buffer pH 7.6 and gas chromatography-mass spectrometry using deuterated internal standards. For interpretation, the sum of the concentrations of the four esters C(FAEE) was used with the cut-off's 0.5 ng/mg for the proximal scalp hair segment 0-3 cm or less and 1.0 ng/mg for scalp hair samples with a length between 3 and 6 cm and for body hair. C(FAEE) ranged from 0.11 to 31 ng/mg (mean 1.77 ng/mg, median 0.82 ng/mg). The mean concentration ratio between the 4 esters was 8:45:38:9. 298 cases had C(FAEE) above the cut-off's. Self-reported drinking data were obtained in 553 of the cases in the categories abstinent (156 cases), moderate drinking (252 cases) and excessive drinking (145 cases). Median and box-plot data clearly demonstrate differentiation of these ingestor sub-populations by C(FAEE). However, in the abstinent and moderate groups the consumption was frequently underreported (37 and 110 cases positive) whereas in the group self-reported excessive drinking 32 cases were negative. Comparison of C(FAEE) with carbohydrate-deficient transferrin (CDT) in 139 cases and gamma-glutamyltransferase (GGT) in 136 cases showed a good agreement in CDT- and GGT positive cases (27/28 and 32/41) but a large portion of the negative CDT- and GGT-results with positive hair test (44/100 and 48/95) which is explained mainly by the much shorter time window of CDT and GGT. No significant correlation was found between persons weight and C(FAEE) showing that the test is not biased against physical fitness or obesity. Furthermore, there was no statistically significant difference between scalp hair (541 samples) and hair from other body sites (84 samples). In conclusion, FAEE in hair appeared to be suitable markers for the detection of excessive drinking. However, as there is no proportionality between drinking amount and C(FAEE), the additional use of other markers can increase the reliability of the interpretation. Copyright 2009 Elsevier Ireland Ltd. All rights reserved.

Mapping surrogate gasoline compositions into RON/MON space

DOE Office of Scientific and Technical Information (OSTI.GOV)

Morgan, Neal; Kraft, Markus; Smallbone, Andrew

2010-06-15

In this paper, new experimentally determined octane numbers (RON and MON) of blends of a tri-component surrogate consisting of toluene, n-heptane, i-octane (called toluene reference fuel TRF) arranged in an augmented simplex design are used to derive a simple response surface model for the octane number of any arbitrary TRF mixture. The model is second-order in its complexity and is shown to be more accurate to the standard ''linear-by-volume'' (LbV) model which is often used when no other information is available. Such observations are due to the existence of both synergistic and antagonistic blending of the octane numbers between themore » three components. In particular, antagonistic blending of toluene and iso-octane leads to a maximum in sensitivity that lies on the toluene/iso-octane line. The model equations are inverted so as to map from RON/MON space back into composition space. Enabling one to use two simple formulae to determine, for a given fuel with known RON and MON, the volume fractions of toluene, n-heptane and iso-octane to be blended in order to emulate that fuel. HCCI engine simulations using gasoline with a RON of 98.5 and a MON of 88 were simulated using a TRF fuel, blended according to the derived equations to match the RON and MON. The simulations matched the experimentally obtained pressure profiles well, especially when compared to simulations using only PRF fuels which matched the RON or MON. This suggested that the mapping is accurate and that to emulate a refinery gasoline, it is necessary to match not only the RON but also the MON of the fuel. (author)« less

Investigation of spray characteristics from a low-pressure common rail injector for use in a homogeneous charge compression ignition engine

NASA Astrophysics Data System (ADS)

Lee, Kihyung; Reitz, Rolf D.

2004-03-01

Homogeneous charge compression ignition (HCCI) combustion provides extremely low levels of pollutant emissions, and thus is an attractive alternative for future IC engines. In order to achieve a uniform mixture distribution within the engine cylinder, the characteristics of the fuel spray play an important role in the HCCI engine concept. It is well known that high-pressure common rail injection systems, mainly used in diesel engines, achieve poor mixture formation because of the possibility of direct fuel impingement on the combustion chamber surfaces. This paper describes spray characteristics of a low-pressure common rail injector which is intended for use in an HCCI engine. Optical diagnostics including laser diffraction and phase Doppler methods, and high-speed camera photography, were applied to measure the spray drop diameter and to investigate the spray development process. The drop sizing results of the laser diffraction method were compared with those of a phase Doppler particle analyser (PDPA) to validate the accuracy of the experiments. In addition, the effect of fuel properties on the spray characteristics was investigated using n-heptane, Stoddard solvent (gasoline surrogate) and diesel fuel because HCCI combustion is sensitive to the fuel composition. The results show that the injector forms a hollow-cone sheet spray rather than a liquid jet, and the atomization efficiency is high (small droplets are produced). The droplet SMD ranged from 15 to 30 µm. The spray break-up characteristics were found to depend on the fuel properties. The break-up time for n-heptane is shorter and the drop SMD is smaller than that of Stoddard solvent and diesel fuel.

Recovery of precious metals from space

NASA Technical Reports Server (NTRS)

Freiser, Henry

1991-01-01

The overall objective is to develop efficient and economical separation and recovery methods for the platinum group and other precious metals. The separation of Pd(II) from Pt(II), Ir(III), and Rh(III) with trioctylphosphine oxide (TOPO) in heptane using centrifugal partition chromatography (CPC) was investigated. Activities to achieve this objective focussed on selection and evaluation of extraction systems for the PGM and modification of selected systems for multistage operation with a view to scaling up to desired macro levels. On the basis of preliminary evaluation of a series of simple metal complexing agents and chelating agents, the TOPO in heptane was selected as a likely system for isolating of Pd(II) and Pt(II) from the other PGM. A multistage apparatus capable of configuration as a simple rugged device, a centrifugal partition chromatograph (CPC), was shown to be effective. The extraction of Pd(II) was studied by CPC and batch solvent extraction. The distribution ratios for Pd(II) determined by both methods agree well. In low HCl concentrations (less than 0.1 M), the extracted species was PdCl2.(TOPO)2, irrespective of the chloride concentration, while at acid concentrations above 0.1 M, the Pd was extracted as the ion pair, 2(TOPO.H+).(PdCl4)2-. Base line separation of Pd(II) and Pt(II) in CPC was obtained under a variety of chloride and HCl concentration. It was demonstrated that the efficiency of CPC for metal separation was limited by chemical kinetic factors rather than instrumental factors, strongly suggesting that dramatic improvements can be achieved by studying reaction kinetics of formation and dissociation of the extractable metal complex.

Combustion Characteristics in a Non-Premixed Cool-Flame Regime of n-Heptane in Microgravity

NASA Technical Reports Server (NTRS)

Takahashi, Fumiaki; Katta, Viswanath R.; Hicks, Michael C.

2015-01-01

A series of distinct phenomena have recently been observed in single-fuel-droplet combustion tests performed on the International Space Station (ISS). This study attempts to simulate the observed flame behavior numerically using a gaseous n-heptane fuel source in zero gravity and a time-dependent axisymmetric (2D) code, which includes a detailed reaction mechanism (127 species and 1130 reactions), diffusive transport, and a radiation model (for CH4, CO, CO2, H2O, and soot). The calculated combustion characteristics depend strongly on the air velocity around the fuel source. In a near-quiescent air environment (< or = 2 mm/s), with a sufficiently large fuel injection velocity (1 cm/s), a growing spherical diffusion flame extinguishes at ˜1200 K due to radiative heat losses. This is typically followed by a transition to the low-temperature (cool-flame) regime with a reaction zone (at ˜700 K) in close proximity to the fuel source. The 'cool flame' regime is formed due to the negative temperature coefficient in the low-temperature chemistry. After a relatively long period (˜18 s) of the cool flame regime, a flash re-ignition occurs, associated with flame-edge propagation and subsequent extinction of the re-ignited flame. In a low-speed (˜3 mm/s) airstream (which simulates the slight droplet movement), the diffusion flame is enhanced upstream and experiences a local extinction downstream at ˜1200 K, followed by steady flame pulsations (˜0.4 Hz). At higher air velocities (4-10 mm/s), the locally extinguished flame becomes steady state. The present axisymmetric computational approach helps in revealing the non-premixed 'cool flame' structure and 2D flame-flow interactions observed in recent microgravity droplet combustion experiments.

In silico prediction of medium effects on esterification equilibrium using the COSMO-RS method.

PubMed

Fermeglia, Maurizio; Braiuca, Paolo; Gardossi, Lucia; Pricl, Sabrina; Halling, Peter J

2006-01-01

This paper presents a new approach for predicting solvent effects on esterification reactions of industrial importance in the field of biocatalysis. The COSMO-RS method has been used to calculate the activity coefficients of the chemical species involved in various reactions, carried out in different solvents. For comparison we also used the traditional UNIFAC method. Three lipase-catalyzed esterifications were considered: (1) 1-dodecanoic acid with menthol in n-hexane, n-heptane, cyclohexane, 2,2,4-trimethylpentane, toluene, acetonitrile, and 2-methyl-2-butanol; (2) 1-dodecanoic acid and 1-dodecanol in n-hexane, n-heptane, cyclohexane, 2,2,4-trimethylpentane, and toluene; and (3) glycerol and n-octanoic acid in acetonitrile, benzene, and toluene and in the neat reaction mixture (without any solvent). Predicted activities were used to calculate the thermodynamic equilibrium ratio. This should be independent of medium, and the variation in COSMO-RS values is at most 9-fold (corresponding to a DeltaG degrees of about 5.5 kJ/mol, which would still be a very useful prediction) and often only 2-fold (corresponding to less than 2 kJ/mol or 0.5 kcal/mol, therefore comparable with experimental error). UNIFAC is weaker, especially when important roles are played by conformational freedom, intramolecular interactions, strong polar effects, and charge distribution of molecules in the mixture. The relative percent deviations from the mean of equilibrium constants in different solvents range between 17 and 49 for COSMO-RS versus 32 to 65 for UNIFAC. The COSMO-RS method opens up new perspectives for the development of theoretical models for solvent selection with general applicability.

Polyphenylenesulfide, noxon® an ozone scavenger for the analysis of oxygenated terpenes in air

NASA Astrophysics Data System (ADS)

Calogirou, A.; Duane, M.; Kotzias, D.; Lahaniati, M.; Larsen, B. R.

During sampling, oxygenated terpenes may undergo decomposition through reaction with atmospheric ozone. We have studied their ozonolytic decomposition during preconcentration on Tenax. The saturated. terpenoids 1,8-cineole, bornyl acetate nopinone and pinonaldehyde are practically unaffected by ozone in the range of 8 to 120 ppbv. Compounds which contain one or more C-C double bonds are decomposed in the order: linalool ≈ citronellal ≈ 6-methyl-5-hepten-2-one > citral > 4-acetyl-1-methyl-cyclohexane > 3-(1-methylethenyl)-6-oxo-heptanal > myrtenal ≈ 2-methyl-3-buten-2-ol. The degree of decomposition varies from 0 to 5% for the least reactive to 80 to 90% for the most reactive compounds. A broad range of material was investigated as potential ozone scavengers. By using the polymer noXon (polyphenylenesulfide) all the investigated compounds could be sampled with quantitative recoveries even at high ozone mixing ratios (95-110 ppbv). This ozone scrubber was tested for sampling of terpene oxidation products on Tenax and dinitrophenylhydrazine impregnated C 18-silicagel cartridges. Recoveries from 85 to 110% were obtained for all investigated compounds. The method was used for the analysis of oxidation products of terpenes in ambient air in three campaigns. Attention was focused on nopinone from β-pinene, pinonaldehyde from α-pinene, 3-(1-methylethenyl)-6-oxo-heptanal and 4-acetyl-1-methyl-cyclohexane from limonene, and 5-(1-methylethyl)-bicyclo[3.1.0] hexan-2-one from sabinene. Nopinone was the only product which could be frequently detected in ratios from 0 to 90% of the measured β-pinene concentrations. Pinonaldehyde was encountered only once (30% of α-pinene) while the other products were not found. These data have to be seen as a first attempt to measure terpene oxidation products in the troposphere.

Evaluation of Vitamin D3 and D2 Stability in Fortified Flat Bread Samples During Dough Fermentation, Baking and Storage.

PubMed

Tabibian, Mehrnaz; Torbati, Mohammadali; Afshar Mogaddam, Mohammad Reza; Mirlohi, Maryam; Sadeghi, Malihe; Mohtadinia, Javad

2017-06-01

Purpose: Vitamin D, a fat-soluble secosteroid, has a significant role in bone metabolism and helps calcium absorption in the body. Since vitamin D concentration is altered in fortified foods and dietary supplements, the actual amount of vitamin D may differ from the label value. Methods: In this study, the concentrations of vitamin D 2 and D 3 of fortified bread sample were analytically determined. For this purpose, dough or homogenized bread sample was saponified using potassium hydroxide solution (30%, w/v) at 80°C, and the saponified analytes were extracted into n -heptane followed by liquid-liquid extraction. Then n -heptane fraction was evaporated to dryness and the sample was reconstituted in methanol. The effect of different parameters was evaluated by one variable at one-time strategy. Results: The analytes concentrations were evaluated in dough fermentation, baking and storage steps. The effect of temperature in dough fermentation and baking was evaluated at the range of 5-30 and 200-250°C, respectively. Also, the fermentation time was studied in the range of 0-120 min. The analytes concentrations were followed for 1 to 5 days after baking. The results indicated that dough fermentation temperature has no significant effect on the concentration of the analytes. On the other hand, when the dough fermentation time and baking temperature are increased, the analytes concentrations are decreased. Also, the storage duration of the spiked bread samples decreased the analytes concentrations after one day. Conclusion: Based on the obtained results, baking the dough at high temperatures lead to decrease in vitamin levels.

Skeletal mechanism generation for surrogate fuels using directed relation graph with error propagation and sensitivity analysis

DOE Office of Scientific and Technical Information (OSTI.GOV)

Niemeyer, Kyle E.; Sung, Chih-Jen; Raju, Mandhapati P.

2010-09-15

A novel implementation for the skeletal reduction of large detailed reaction mechanisms using the directed relation graph with error propagation and sensitivity analysis (DRGEPSA) is developed and presented with examples for three hydrocarbon components, n-heptane, iso-octane, and n-decane, relevant to surrogate fuel development. DRGEPSA integrates two previously developed methods, directed relation graph-aided sensitivity analysis (DRGASA) and directed relation graph with error propagation (DRGEP), by first applying DRGEP to efficiently remove many unimportant species prior to sensitivity analysis to further remove unimportant species, producing an optimally small skeletal mechanism for a given error limit. It is illustrated that the combination ofmore » the DRGEP and DRGASA methods allows the DRGEPSA approach to overcome the weaknesses of each, specifically that DRGEP cannot identify all unimportant species and that DRGASA shields unimportant species from removal. Skeletal mechanisms for n-heptane and iso-octane generated using the DRGEP, DRGASA, and DRGEPSA methods are presented and compared to illustrate the improvement of DRGEPSA. From a detailed reaction mechanism for n-alkanes covering n-octane to n-hexadecane with 2115 species and 8157 reactions, two skeletal mechanisms for n-decane generated using DRGEPSA, one covering a comprehensive range of temperature, pressure, and equivalence ratio conditions for autoignition and the other limited to high temperatures, are presented and validated. The comprehensive skeletal mechanism consists of 202 species and 846 reactions and the high-temperature skeletal mechanism consists of 51 species and 256 reactions. Both mechanisms are further demonstrated to well reproduce the results of the detailed mechanism in perfectly-stirred reactor and laminar flame simulations over a wide range of conditions. The comprehensive and high-temperature n-decane skeletal mechanisms are included as supplementary material with this article. (author)« less

Evaluation of Vitamin D3 and D2 Stability in Fortified Flat Bread Samples During Dough Fermentation, Baking and Storage

PubMed Central

Tabibian, Mehrnaz; Torbati, Mohammadali; Afshar Mogaddam, Mohammad Reza; Mirlohi, Maryam; Sadeghi, Malihe; Mohtadinia, Javad

2017-01-01

Purpose: Vitamin D, a fat-soluble secosteroid, has a significant role in bone metabolism and helps calcium absorption in the body. Since vitamin D concentration is altered in fortified foods and dietary supplements, the actual amount of vitamin D may differ from the label value. Methods: In this study, the concentrations of vitamin D2 and D3 of fortified bread sample were analytically determined. For this purpose, dough or homogenized bread sample was saponified using potassium hydroxide solution (30%, w/v) at 80°C, and the saponified analytes were extracted into n-heptane followed by liquid-liquid extraction. Then n-heptane fraction was evaporated to dryness and the sample was reconstituted in methanol. The effect of different parameters was evaluated by one variable at one-time strategy. Results: The analytes concentrations were evaluated in dough fermentation, baking and storage steps. The effect of temperature in dough fermentation and baking was evaluated at the range of 5-30 and 200-250°C, respectively. Also, the fermentation time was studied in the range of 0-120 min. The analytes concentrations were followed for 1 to 5 days after baking. The results indicated that dough fermentation temperature has no significant effect on the concentration of the analytes. On the other hand, when the dough fermentation time and baking temperature are increased, the analytes concentrations are decreased. Also, the storage duration of the spiked bread samples decreased the analytes concentrations after one day. Conclusion: Based on the obtained results, baking the dough at high temperatures lead to decrease in vitamin levels. PMID:28761835

A Treatment of Measurements of Heptane Droplet Combustion Aboard MSL-1

NASA Technical Reports Server (NTRS)

Ackerman, M. D.; Colantonio, R. O.; Crouch, R. K.; Dryer, F. L.; Haggard, J. B.; Linteris, G. T.; Marchese, A. J.; Nayagam, V.; Voss, J. E.; Williams, F. A.

2003-01-01

Results of measurements on the burning of free n-heptane droplets (that is, droplets without fiber supports) performed in Spacelab during the flights of the first Microgravity Science Laboratory (MSL-1) are presented. The droplet combustion occurred in oxidizing atmospheres which were at an ambient temperature within a few degrees of 300 K. A total of 34 droplets were burned in helium-oxygen atmospheres having oxygen mole fractions ranging from 20 to 50 percent, at pressures from 0.25 to 1.00 bar. In addition, four droplets were burned in air at 1.00 bar, bringing the total number of droplets for which combustion data were secured to 38; two of these four air tests were fiber-supported to facilitate comparisons with other fiber-support experiments, results of which also are given here. Initial diameters of free droplets ranged from about 1 to 4 mm. The primary data obtained were histories of droplet diameters, recorded in backlight on 35 mm film at 80 frames per second, and histories of flame diameters, inferred from emissions through a narrow-band interference filter centered at the 310 micron OH chemiluminescent ultraviolet band, recorded at 30 frames per second by a intensified-array camera. These data are reported here both in raw form and in a smoothed form with estimated error bars. In addition, summaries are presented of measured burning-rate constants, final droplet diameters, and final flame diameters. Both diffusive and radiative extinctions were exhibited under different conditions. Although some interpretations are reported and conclusions drawn concerning the combustion mechanisms, the principal intent of this report is to provide a complete, documented data set for future analysis.

A Sensitive Microplate Assay for Lipase Activity Measurement Using Olive Oil Emulsion Substrate: Modification of the Copper Soap Colorimetric Method.

PubMed

Mustafa, Ahmad; Karmali, Amin; Abdelmoez, Wael

2016-01-01

The present work involves a sensitive high-throughput microtiter plate based colorimetric assay for estimating lipase activity using cupric acetate pyridine reagent (CAPR). In the first approach, three factors two levels factorial design methodology was used to evaluate the interactive effect of different parameters on the sensitivity of the assay method. The optimization study revealed that the optimum CAPR concentration was 7.5% w/v, the optimum solvent was heptane and the optimum CAPR pH was 6. In the second approach, the optimized colorimetric microplate assay was used to measure lipase activity based on enzymatic hydrolysis of olive oil emulsion substrate at 37°C and 150 rpm. The emulsion substrates were formulated by using olive oil, triton X-100 (10% v/v in pH 8) and sodium phosphate buffer of pH 8 in ratio of 1:1:1 in the case of Candida sp. lipase. While in the case of immobilized lipozyme RMIM, The emulsion substrates were formulated by using olive oil, triton X-100 (1% v/v in pH 8) and sodium phosphate buffer of pH 8 in ratio of 2:1:1. Absorbance was measured at 655 nm. The stability of this assay (in terms of colored heptane phase absorbance readings) retained more than 92.5% after 24 h at 4°C compared to the absorbance readings measured at zero time. In comparison with other lipase assay methods, beside the developed sensitivity, the reproducibility and the lower limit of detection (LOD) of the proposed method, it permits analyzing of 96 samples at one time in a 96-well microplate. Furthermore, it consumes small quantities of chemicals and unit operations.

Computational Screening of Nanoporous Materials for Hexane and Heptane Isomer Separation

DOE PAGES

Chung, Yongchul G.; Bai, Peng; Haranczyk, Maciej; ...

2017-07-05

Computational high-throughput screening was carried out to assess a large number of experimentally reported metal–organic frameworks (MOFs) and zeolites for their utility in hexane isomer separation. Through the paper, we identified many MOFs and zeolites with high selectivity (S L+M > 10) for the group of n-hexane, 2-methylpentane, and 3-methylpentane (linear and monobranched isomers) versus 2,2-dimethylbutane and 2,3-dimethylbutane (dibranched isomers). This group of selective sorbents includes VICDOC (Fe 2(BDP) 3), a MOF with triangular pores that is known to exhibit high isomer selectivity and capacity. For three of these structures, the adsorption isotherms for a 10-component mixture of hexane andmore » heptane isomers were calculated. Subsequent simulations of column breakthrough curves showed that the DEYVUA MOF exhibits a longer process cycle time than VICDOC MOF or MRE zeolite, which are previously reported, high-performing materials, illustrating the importance of capacity in designing MOFs for practical applications. Among the identified candidates, we synthesized and characterized a MOF in a new copper form with high predicted adsorbent capacity (q L+M > 1.2 mol/L) and moderately high selectivity (S L+M ≈ 10). In conclusion, we examined the role of pore shape in hexane isomer separations, especially of triangular-shaped pores. We show through the potential energy surface and three-dimensional siting analyses that linear alkanes do not populate the corners of narrow triangular channels and that structures with nontriangular pores can efficiently separate hexane isomers. Detailed thermodynamic analysis illustrates how differences in the free energy of adsorption contribute to shape-selective separation in nanoporous materials.« less

Computational Screening of Nanoporous Materials for Hexane and Heptane Isomer Separation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Yongchul G.; Bai, Peng; Haranczyk, Maciej

Computational high-throughput screening was carried out to assess a large number of experimentally reported metal–organic frameworks (MOFs) and zeolites for their utility in hexane isomer separation. Through the paper, we identified many MOFs and zeolites with high selectivity (S L+M > 10) for the group of n-hexane, 2-methylpentane, and 3-methylpentane (linear and monobranched isomers) versus 2,2-dimethylbutane and 2,3-dimethylbutane (dibranched isomers). This group of selective sorbents includes VICDOC (Fe 2(BDP) 3), a MOF with triangular pores that is known to exhibit high isomer selectivity and capacity. For three of these structures, the adsorption isotherms for a 10-component mixture of hexane andmore » heptane isomers were calculated. Subsequent simulations of column breakthrough curves showed that the DEYVUA MOF exhibits a longer process cycle time than VICDOC MOF or MRE zeolite, which are previously reported, high-performing materials, illustrating the importance of capacity in designing MOFs for practical applications. Among the identified candidates, we synthesized and characterized a MOF in a new copper form with high predicted adsorbent capacity (q L+M > 1.2 mol/L) and moderately high selectivity (S L+M ≈ 10). In conclusion, we examined the role of pore shape in hexane isomer separations, especially of triangular-shaped pores. We show through the potential energy surface and three-dimensional siting analyses that linear alkanes do not populate the corners of narrow triangular channels and that structures with nontriangular pores can efficiently separate hexane isomers. Detailed thermodynamic analysis illustrates how differences in the free energy of adsorption contribute to shape-selective separation in nanoporous materials.« less

Two-stage autoignition and edge flames in a high pressure turbulent jet

DOE PAGES

Krisman, Alex; Hawkes, Evatt R.; Chen, Jacqueline H.

2017-07-04

A three-dimensional direct numerical simulation is conducted for a temporally evolving planar jet of n-heptane at a pressure of 40 atmospheres and in a coflow of air at 1100 K. At these conditions, n-heptane exhibits a two-stage ignition due to low- and high-temperature chemistry, which is reproduced by the global chemical model used in this study. The results show that ignition occurs in several overlapping stages and multiple modes of combustion are present. Low-temperature chemistry precedes the formation of multiple spatially localised high-temperature chemistry autoignition events, referred to as ‘kernels’. These kernels form within the shear layer and core ofmore » the jet at compositions with short homogeneous ignition delay times and in locations experiencing low scalar dissipation rates. An analysis of the kernel histories shows that the ignition delay time is correlated with the mixing rate history and that the ignition kernels tend to form in vortically dominated regions of the domain, as corroborated by an analysis of the topology of the velocity gradient tensor. Once ignited, the kernels grow rapidly and establish edge flames where they envelop the stoichiometric isosurface. A combination of kernel formation (autoignition) and the growth of existing burning surface (via edge-flame propagation) contributes to the overall ignition process. In conclusion, an analysis of propagation speeds evaluated on the burning surface suggests that although the edge-flame speed is promoted by the autoignitive conditions due to an increase in the local laminar flame speed, edge-flame propagation of existing burning surfaces (triggered initially by isolated autoignition kernels) is the dominant ignition mode in the present configuration.« less

Engineering development of selective agglomeration: Task 5, Bench- scale process testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-09-01

Under the overall objectives of DOE Contract ``Engineering Development of Selective Agglomeration,`` there were a number of specific objectives in the Task 5 program. The prime objectives of Task 5 are highlighted below: (1) Maximize process performance in pyritic sulfur rejection and BTU recovery, (2) Produce a low ash product, (3) Compare the performance of the heavy agglomerant process based on diesel and the light agglomerant process using heptane, (4) Define optimum processing conditions for engineering design, (5) Provide first-level evaluation of product handleability, and (6) Explore and investigate process options/ideas which may enhance process performance and/or product handleability.

Engineering development of selective agglomeration: Task 5, Bench- scale process testing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1991-09-01

Under the overall objectives of DOE Contract Engineering Development of Selective Agglomeration,'' there were a number of specific objectives in the Task 5 program. The prime objectives of Task 5 are highlighted below: (1) Maximize process performance in pyritic sulfur rejection and BTU recovery, (2) Produce a low ash product, (3) Compare the performance of the heavy agglomerant process based on diesel and the light agglomerant process using heptane, (4) Define optimum processing conditions for engineering design, (5) Provide first-level evaluation of product handleability, and (6) Explore and investigate process options/ideas which may enhance process performance and/or product handleability.

Isolated Liquid Droplet Combustion: Inhibition and Extinction Studies

NASA Technical Reports Server (NTRS)

Dryer, F. L.; Kroenlein, K. G.; Kazakov, A.; Williams, F. A.; Nayagam, V.

2004-01-01

Introduction of fire suppressants to the ambient environment surrounding a heterogeneous diffusion flame may be an inefficient technique for fire safety in systems without buoyant flows. Carbon dioxide substitution for nitrogen diluent leads to significant modifications of the sphero-symmetric burning behavior of isolated n-heptane droplets, partly through increased heat capacity within the gaseous diffusion flame, but mostly because of modifications in spectral radiative coupling in the gas phase. Effects of longer time scale phenomena such as sooting and slow gas-phase/droplet convection remain to be determined. Similar methodologies can be applied to evaluate the effects and efficacy of chemical inhibitors in the liquid and gas phases.

Photoinduced underwater superoleophobicity of TiO2 thin films.

PubMed

Sawai, Yusuke; Nishimoto, Shunsuke; Kameshima, Yoshikazu; Fujii, Eiji; Miyake, Michihiro

2013-06-11

The photoinduced wettabilities of water, n-hexadecane, dodecane, and n-heptane on a flat TiO2 surface prepared by a sol-gel method-based coating were investigated. An amphiphilic surface produced by UV irradiation exhibited underwater superoleophobicity with an extremely high static oil contact angle (CA) of over 160°. The TiO2 surface almost completely repelled the oil droplet in water. A robust TiO2 surface with no fragile nanomicrostructure was fabricated on a Ti mesh with a pore size of approximately 150 μm. The fabricated mesh was found to be applicable as an oil/water separation filter.

High-performance liquid chromatographic method for guanylhydrazone compounds.

PubMed

Cerami, C; Zhang, X; Ulrich, P; Bianchi, M; Tracey, K J; Berger, B J

1996-01-12

A high-performance liquid chromatographic method has been developed for a series of aromatic guanylhydrazones that have demonstrated therapeutic potential as anti-inflammatory agents. The compounds were separated using octadecyl or diisopropyloctyl reversed-phase columns, with an acetonitrile gradient in water containing heptane sulfonate, tetramethylammonium chloride, and phosphoric acid. The method was used to reliably quantify levels of analyte as low as 785 ng/ml, and the detector response was linear to at least 50 micrograms/ml using a 100 microliters injection volume. The assay system was used to determine the basic pharmacokinetics of a lead compound, CNI-1493, from serum concentrations following a single intravenous injection in rats.

A Model of Reduced Kinetics for Alkane Oxidation Using Constituents and Species for N-Heptane

NASA Technical Reports Server (NTRS)

Harstad, Kenneth G.; Bellan, Josette

2011-01-01

The reduction of elementary or skeletal oxidation kinetics to a subgroup of tractable reactions for inclusion in turbulent combustion codes has been the subject of numerous studies. The skeletal mechanism is obtained from the elementary mechanism by removing from it reactions that are considered negligible for the intent of the specific study considered. As of now, there are many chemical reduction methodologies. A methodology for deriving a reduced kinetic mechanism for alkane oxidation is described and applied to n-heptane. The model is based on partitioning the species of the skeletal kinetic mechanism into lights, defined as those having a carbon number smaller than 3, and heavies, which are the complement of the species ensemble. For modeling purposes, the heavy species are mathematically decomposed into constituents, which are similar but not identical to groups in the group additivity theory. From analysis of the LLNL (Lawrence Livermore National Laboratory) skeletal mechanism in conjunction with CHEMKIN II, it is shown that a similarity variable can be formed such that the appropriately non-dimensionalized global constituent molar density exhibits a self-similar behavior over a very wide range of equivalence ratios, initial pressures and initial temperatures that is of interest for predicting n-heptane oxidation. Furthermore, the oxygen and water molar densities are shown to display a quasi-linear behavior with respect to the similarity variable. The light species ensemble is partitioned into quasi-steady and unsteady species. The reduced model is based on concepts consistent with those of Large Eddy Simulation (LES) in which functional forms are used to replace the small scales eliminated through filtering of the governing equations; in LES, these small scales are unimportant as far as the overwhelming part of dynamic energy is concerned. Here, the scales thought unimportant for recovering the thermodynamic energy are removed. The concept is tested by using tabular information from the LLNL skeletal mechanism in conjunction with CHEMKIN II utilized as surrogate ideal functions replacing the necessary functional forms. The test reveals that the similarity concept is indeed justified and that the combustion temperature is well predicted, but that the ignition time is over-predicted, a fact traced to neglecting a detailed description of the processes leading to the heavies chemical decomposition. To palliate this deficiency, functional modeling is incorporated into this conceptual reduction in addition to the modeling the evolution of the global constituent molar density, the enthalpy evolution of the heavies, the contribution to the reaction rate of the unsteady lights from other light species and from the heavies, the molar density evolution of oxygen and water, and the mole fractions of the quasisteady light species. The model is compact in that there are only nine species-related progress variables. Results are presented showing the performance of the model for predicting the temperature and species evolution. The model reproduces the ignition time over a wide range of equivalence ratios, initial pressure, and initial temperature.

Rate constants for OH with selected large alkanes : shock-tube measurements and an improved group scheme.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sivaramakrishnan, R.; Michael, J. V.; Chemical Sciences and Engineering Division

High-temperature rate constant experiments on OH with the five large (C{sub 5}-C{sub 8}) saturated hydrocarbons n-heptane, 2,2,3,3-tetramethylbutane (2,2,3,3-TMB), n-pentane, n-hexane, and 2,3-dimethylbutane (2,3-DMB) were performed with the reflected-shock-tube technique using multipass absorption spectrometric detection of OH radicals at 308 nm. Single-point determinations at {approx}1200 K on n-heptane, 2,2,3,3-TMB, n-hexane, and 2,3-DMB were previously reported by Cohen and co-workers; however, the present work substantially extends the database to both lower and higher temperature. The present experiments span a wide temperature range, 789-1308 K, and represent the first direct measurements of rate constants at T > 800 K for n-pentane. The presentmore » work utilized 48 optical passes corresponding to a total path length of {approx}4.2 m. As a result of this increased path length, the high OH concentration detection sensitivity permitted pseudo-first-order analyses for unambiguously measuring rate constants. The experimental results can be expressed in Arrhenius form in units of cm{sup 3} molecule{sup -1} s{sup -1} as follows: K{sub OH+n-heptane} = (2.48 {+-} 0.17) x 10{sup -10} exp[(-1927 {+-} 69 K)/T] (838-1287 K); k{sub OH+2,2,3,3-TMB} = (8.26 {+-} 0.89) x 10{sup -11} exp[(-1337 {+-} 94 K)/T] (789-1061 K); K{sub OH+n-pentane} = (1.60 {+-} 0.25) x 10{sup -10} exp[(-1903 {+-} 146 K)/T] (823-1308 K); K{sub OH+n-hexane} = (2.79 {+-} 0.39) x 10{sup -10} exp[(-2301 {+-} 134 K)/T] (798-1299 K); and k{sub OH+2,3-DMB} = (1.27 {+-} 0.16) x 10{sup -10} exp[(-1617 {+-} 118 K)/T] (843-1292 K). The available experimental data, along with lower-T determinations, were used to obtain evaluations of the experimental rate constants over the temperature range from {approx}230 to 1300 K for most of the title reactions. These extended-temperature-range evaluations, given as three-parameter fits, are as follows: k{sub OH+n-heptane} = 2.059 x 10{sup -5}T{sup 1.401} exp(33 K/T) cm{sup 3} molecule{sup -1} s{sup -1} (241-1287 K); k{sub OH+2,2,3,3-TMB} = 6.835 x 10{sup -17}T{sup 1.886} exp(-365 K/T) cm{sup 3} molecule{sup -1} s{sup -1} (290-1180 K); k{sub OH+n-pentane} = 2.495 x 10{sup -16}T{sup 1.649} exp(80 K/T) cm{sup 3} molecule{sup -1} s{sup -1} (224-1308 K); k{sub OH+n-hexane} = 3.959 x 10{sup -18}T{sup 2.218} exp(443 K/T) cm{sup 3} molecule{sup -1} s{sup -1} (292-1299 K); and k{sub OH+2,3-DMB} = 2.287 x 10{sup -17}T{sup 1.958} exp(365 K/T) cm{sup 3} molecule{sup -1} s{sup -1} (220-1292 K). The experimental data and the evaluations obtained for these five larger alkanes in the present work were used along with prior data/evaluations obtained in this laboratory for H abstractions by OH from a series of smaller alkanes (C{sub 3}?C{sub 5}) to devise rate rules for abstractions from various types of primary, secondary, and tertiary H atoms. Specifically, the current scheme was applied with good success to H abstractions by OH from a series of n-alkanes (n-octane through n-hexadecane). The total rate constants using this group scheme for reactions of OH with selected large alkanes are given as three-parameter fits in this article. The rate constants for the various abstraction channels in any large n-alkane can also be obtained using the groups listed in this article. The present group scheme serves to reduce the uncertainties in rate constants for OH + alkane reactions.« less

Mitsunobu alkylation of cancerostatic 5-fluorouridine with (2E)-10-hydroxydec-2-enoic acid, a fatty acid from royal jelly with multiple biological activities.

PubMed

Ottenhaus, Vanessa; Rosemeyer, Helmut

2015-09-01

5-Fluorouridine (1) - a nucleoside antimetabolite with strong cancerostatic properties - was protected i) at the 2'- and 3'-OH groups with a heptan-4-ylidene residue and ii) at the 5'-OH group with a (4-methoxyphenyl)(diphenyl)methyl residue. This fully protected compound, 3, was submitted to a Mitsunobu reaction with the N-hydroxysuccinimide (NHS) ester, 5, of (2E)-10-hydroxydec-2-enoic acid (4) which gave nucleolipid 6. The latter was detritylated with Cl2 CHCOOH to yield the co-drug 7 as NHS ester. Copyright © 2015 Verlag Helvetica Chimica Acta AG, Zürich.

Combustion characteristics of various fuels during research octane number testing on an instrumented CFR F1/F2 engine

DOE PAGES

Kolodziej, Christopher P.; Wallner, Thomas

2017-04-01

The Cooperative Fuels Research (CFR) engine is the long-established standard for characterization of fuel knock resistance in spark-ignition internal combustion engines. Despite its measurements of RON and MON being widely used, there is little understanding of what governs the CFR octane rating for fuels of various chemical compositions compared to primary reference fuels (iso-octane and n-heptane). Some detailed combustion characteristics were measured on a highly instrumented CFR F1/F2 engine during RON testing of fuels with significantly different chemical composition. Our results revealed differences in the cylinder pressure and temperature conditions, as well as knocking characteristics.

DOE Office of Scientific and Technical Information (OSTI.GOV)

D'yachkov, Aleksei B; Labozin, Valerii P

The results of experiments on the 510 {yields} 578-nm conversion of high-power radiation from a copper vapour laser (CVL) in a dye cell are presented. The use of the efficient laser dye Pyrromethane 597 (PM-597) made it possible to convert the 120-W CVL radiation (72 W at 510 nm + 48 W at 578 nm) into 102-W radiation at 578 nm, which is equivalent to a conversion efficiency of 85%. Photostability of the dye in various solvents is studied. The photostability (more than 45 GJ mole{sup -1}) of PM-597 in n-heptane is found to be higher than that of Rhmore » 6G in ethanol. (control of laser radiation parameters)« less

Combustion characteristics of various fuels during research octane number testing on an instrumented CFR F1/F2 engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolodziej, Christopher P.; Wallner, Thomas

The Cooperative Fuels Research (CFR) engine is the long-established standard for characterization of fuel knock resistance in spark-ignition internal combustion engines. Despite its measurements of RON and MON being widely used, there is little understanding of what governs the CFR octane rating for fuels of various chemical compositions compared to primary reference fuels (iso-octane and n-heptane). Some detailed combustion characteristics were measured on a highly instrumented CFR F1/F2 engine during RON testing of fuels with significantly different chemical composition. Our results revealed differences in the cylinder pressure and temperature conditions, as well as knocking characteristics.

Liquid-liquid equilibrium in the- n-heptane- n-perfluorohexane system

NASA Astrophysics Data System (ADS)

Khairulin, R. A.; Stankus, S. V.; Gruzdev, V. A.; Bityutskii, V. A.

2009-01-01

The shape of the liquid-liquid coexistence curve in the C7H16-C6F14 system in the molar concentration-temperature coordinates close to the critical solution point was studied by narrow-beam gamma-raying of two-phase samples. The molar volumes of the coexisting liquid phases and critical point coordinates (critical temperature T c = 316.266 ± 0.03 K and critical concentration x c = 39.0 ± 0.4 mol % C6F14) were determined. The critical index β of the coexistence curve was found to be 0.322 ± 0.005. The diameter of the coexistence curve did not obey the classic “rectilinear diameter rule.”

Infrared Spectroscopic Investigation on CH Bond Acidity in Cationic Alkanes

NASA Astrophysics Data System (ADS)

Matsuda, Yoshiyuki; Xie, Min; Fujii, Asuka

2016-06-01

We have demonstrated large enhancements of CH bond acidities in alcohol, ether, and amine cations through infrared predissociation spectroscopy based on the vacuum ultraviolet photoionization detection. In this study, we investigate for the cationic alkanes (pentane, hexane, and heptane) with different alkyl chain lengths. The σ electrons are ejected in the ionization of alkanes, while nonbonding electrons are ejected in ionization of alcohols, ethers, and amines. Nevertheless, the acidity enhancements of CH in these cationic alkanes have also been demonstrated by infrared spectroscopy. The correlations of their CH bond acidities with the alkyl chain lengths as well as the mechanisms of their acidity enhancements will be discussed by comparison of infrared spectra and theoretical calculations.

Chemical composition and antibacterial activity of the essential oil from Pyrrosia tonkinensis (Giesenhagen) Ching.

PubMed

Xin, Xiaowei; Liu, Qingshen; Zhang, Yingying; Gao, Demin

2016-01-01

The present study aimed to analyse the chemical components of the essential oil from Pyrrosia tonkinensis by GC-MS and evaluate the in vitro antibacterial activity. Twenty-eight compounds, representing 88.1% of the total essential oil, were identified and the major volatile components were trans-2-hexenal (22.1%), followed by nonanal (12.8%), limonene (9.6%), phytol (8.4%), 1-hexanol (3.8%), 2-furancarboxaldehyde (3.5%) and heptanal (3.1%). The antibacterial assays showed that the essential oil of P. tonkinensis had good antibacterial activities against all the tested microorganisms. This paper first reported the chemical composition and antimicrobial activity of the essential oil from P. tonkinensis.

An augmented Young-Laplace model of an evaporating meniscus in a micro-channel with high heat flux

NASA Technical Reports Server (NTRS)

Wayner, P. C., Jr.; Plawsky, J.; Schonberg, J. A.; Dasgupta, S.

1993-01-01

High flux evaporations from a steady meniscus formed in a 2 micron channel is modeled using the augmented Young-Laplace equation. The heat flux is found to be a function of the long range van der Waals dispersion force which represents interfacial conditions between heptane and various substrates. Heat fluxes of (1.3-1.6) x 10(exp 6) W/m(exp 2) based on the width of the channel are obtained for heptane completely wetting the substrate at 100 C. Small channels are used to obtain these large fluxes. Even though the real contact angle is 0 deg, the apparent contact angle is found to vary between 24.8 deg and 25.6 deg. The apparent contact angle, which represents viscous losses near the contact line, has a large effect on the heat flow rate because of its effect on capillary suction and the area of the meniscus. The interfacial heat flux is modeled using kinetic theory for the evaporation rate. The superheated state depends on the temperature and the pressure of the liquid phase. The liquid pressure differs from the pressure of the vapor phase due to capillarity and long range van der Waals dispersion forces which are relevant in the ultra think film formed at the leading edge of the meniscus. Important pressure gradients in the thin film cause a substantial apparent contact angle for a complete wetting system. The temperature of the liquid is related to the evaporation rate and to the substrate temperature through the steady heat conduction equation. Conduction in the liquid phase is calculated using finite element analysis except in the vicinity of the thin film. A lubrication theory solution for the thin film is combined with the finite element analysis by the method of matched asymptotic expansions.

Exhaled volatile substances mirror clinical conditions in pediatric chronic kidney disease

PubMed Central

Obermeier, Juliane; Trefz, Phillip; Happ, Josephine; Schubert, Jochen K.; Staude, Hagen

2017-01-01

Monitoring metabolic adaptation to chronic kidney disease (CKD) early in the time course of the disease is challenging. As a non-invasive technique, analysis of exhaled breath profiles is especially attractive in children. Up to now, no reports on breath profiles in this patient cohort are available. 116 pediatric subjects suffering from mild-to-moderate CKD (n = 48) or having a functional renal transplant KTx (n = 8) and healthy controls (n = 60) matched for age and sex were investigated. Non-invasive quantitative analysis of exhaled breath profiles by means of a highly sensitive online mass spectrometric technique (PTR-ToF) was used. CKD stage, the underlying renal disease (HUS; glomerular diseases; abnormalities of kidney and urinary tract or polycystic kidney disease) and the presence of a functional renal transplant were considered as classifiers. Exhaled volatile organic compound (VOC) patterns differed between CKD/ KTx patients and healthy children. Amounts of ammonia, ethanol, isoprene, pentanal and heptanal were higher in patients compared to healthy controls (556, 146, 70.5, 9.3, and 5.4 ppbV vs. 284, 82.4, 49.6, 5.30, and 2.78 ppbV). Methylamine concentrations were lower in the patient group (6.5 vs 10.1 ppbV). These concentration differences were most pronounced in HUS and kidney transplanted patients. When patients were grouped with respect to degree of renal failure these differences could still be detected. Ammonia accumulated already in CKD stage 1, whereas alterations of isoprene (linked to cholesterol metabolism), pentanal and heptanal (linked to oxidative stress) concentrations were detectable in the breath of patients with CKD stage 2 to 4. Only weak associations between serum creatinine and exhaled VOCs were noted. Non-invasive breath testing may help to understand basic mechanisms and metabolic adaptation accompanying progression of CKD. Our results support the current notion that metabolic adaptation occurs early during the time course of CKD. PMID:28570715

Evaluating temperature and fuel stratification for heat-release rate control in a reactivity-controlled compression-ignition engine using optical diagnostics and chemical kinetics modeling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Musculus, Mark P. B.; Kokjohn, Sage L.; Reitz, Rolf D.

We investigated the combustion process in a dual-fuel, reactivity-controlled compression-ignition (RCCI) engine using a combination of optical diagnostics and chemical kinetics modeling to explain the role of equivalence ratio, temperature, and fuel reactivity stratification for heat-release rate control. An optically accessible engine is operated in the RCCI combustion mode using gasoline primary reference fuels (PRF). A well-mixed charge of iso-octane (PRF = 100) is created by injecting fuel into the engine cylinder during the intake stroke using a gasoline-type direct injector. Later in the cycle, n-heptane (PRF = 0) is delivered through a centrally mounted diesel-type common-rail injector. This injectionmore » strategy generates stratification in equivalence ratio, fuel blend, and temperature. The first part of this study uses a high-speed camera to image the injection events and record high-temperature combustion chemiluminescence. Moreover, the chemiluminescence imaging showed that, at the operating condition studied in the present work, mixtures in the squish region ignite first, and the reaction zone proceeds inward toward the center of the combustion chamber. The second part of this study investigates the charge preparation of the RCCI strategy using planar laser-induced fluorescence (PLIF) of a fuel tracer under non-reacting conditions to quantify fuel concentration distributions prior to ignition. The fuel-tracer PLIF data show that the combustion event proceeds down gradients in the n-heptane distribution. The third part of the study uses chemical kinetics modeling over a range of mixtures spanning the distributions observed from the fuel-tracer fluorescence imaging to isolate the roles of temperature, equivalence ratio, and PRF number stratification. The simulations predict that PRF number stratification is the dominant factor controlling the ignition location and growth rate of the reaction zone. Equivalence ratio has a smaller, but still significant, influence. Lastly, temperature stratification had a negligible influence due to the NTC behavior of the PRF mixtures.« less

Evaluating temperature and fuel stratification for heat-release rate control in a reactivity-controlled compression-ignition engine using optical diagnostics and chemical kinetics modeling

DOE PAGES

Musculus, Mark P. B.; Kokjohn, Sage L.; Reitz, Rolf D.

2015-04-23

We investigated the combustion process in a dual-fuel, reactivity-controlled compression-ignition (RCCI) engine using a combination of optical diagnostics and chemical kinetics modeling to explain the role of equivalence ratio, temperature, and fuel reactivity stratification for heat-release rate control. An optically accessible engine is operated in the RCCI combustion mode using gasoline primary reference fuels (PRF). A well-mixed charge of iso-octane (PRF = 100) is created by injecting fuel into the engine cylinder during the intake stroke using a gasoline-type direct injector. Later in the cycle, n-heptane (PRF = 0) is delivered through a centrally mounted diesel-type common-rail injector. This injectionmore » strategy generates stratification in equivalence ratio, fuel blend, and temperature. The first part of this study uses a high-speed camera to image the injection events and record high-temperature combustion chemiluminescence. Moreover, the chemiluminescence imaging showed that, at the operating condition studied in the present work, mixtures in the squish region ignite first, and the reaction zone proceeds inward toward the center of the combustion chamber. The second part of this study investigates the charge preparation of the RCCI strategy using planar laser-induced fluorescence (PLIF) of a fuel tracer under non-reacting conditions to quantify fuel concentration distributions prior to ignition. The fuel-tracer PLIF data show that the combustion event proceeds down gradients in the n-heptane distribution. The third part of the study uses chemical kinetics modeling over a range of mixtures spanning the distributions observed from the fuel-tracer fluorescence imaging to isolate the roles of temperature, equivalence ratio, and PRF number stratification. The simulations predict that PRF number stratification is the dominant factor controlling the ignition location and growth rate of the reaction zone. Equivalence ratio has a smaller, but still significant, influence. Lastly, temperature stratification had a negligible influence due to the NTC behavior of the PRF mixtures.« less

Evaluation and optimisation of phenomenological multi-step soot model for spray combustion under diesel engine-like operating conditions

NASA Astrophysics Data System (ADS)

Pang, Kar Mun; Jangi, Mehdi; Bai, Xue-Song; Schramm, Jesper

2015-05-01

In this work, a two-dimensional computational fluid dynamics study is reported of an n-heptane combustion event and the associated soot formation process in a constant volume combustion chamber. The key interest here is to evaluate the sensitivity of the chemical kinetics and submodels of a semi-empirical soot model in predicting the associated events. Numerical computation is performed using an open-source code and a chemistry coordinate mapping approach is used to expedite the calculation. A library consisting of various phenomenological multi-step soot models is constructed and integrated with the spray combustion solver. Prior to the soot modelling, combustion simulations are carried out. Numerical results show that the ignition delay times and lift-off lengths exhibit good agreement with the experimental measurements across a wide range of operating conditions, apart from those in the cases with ambient temperature lower than 850 K. The variation of the soot precursor production with respect to the change of ambient oxygen levels qualitatively agrees with that of the conceptual models when the skeletal n-heptane mechanism is integrated with a reduced pyrene chemistry. Subsequently, a comprehensive sensitivity analysis is carried out to appraise the existing soot formation and oxidation submodels. It is revealed that the soot formation is captured when the surface growth rate is calculated using a square root function of the soot specific surface area and when a pressure-dependent model constant is considered. An optimised soot model is then proposed based on the knowledge gained through this exercise. With the implementation of optimised model, the simulated soot onset and transport phenomena before reaching quasi-steady state agree reasonably well with the experimental observation. Also, variation of spatial soot distribution and soot mass produced at oxygen molar fractions ranging from 10.0 to 21.0% for both low and high density conditions are reproduced.

Formulation reproducing the ignition delays simulated by a detailed mechanism: Application to n-heptane combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Imbert, Bruno; Lafosse, Fabien; Catoire, Laurent

2008-11-15

This article is part of the project to model the kinetics of high-temperature combustions, occurring behind shock waves and in detonation waves. The ''conventional'' semi-empirical correlations of ignition delays have been reformulated, by keeping the Arrhenius equation form. It is shown how a polynomial with 3{sup N} coefficients (where N element of is the number of adjustable kinetic parameters, likely to be simultaneously chosen among the temperature T, the pressure P, the inert fraction X{sub Ar}, and the equivalence ratio {phi}) can reproduce the delays predicted by the Curran et al. [H.J. Curran, P. Gaffuri, W.J. Pitz, C.K. Westbrook, Combust.more » Flame 129 (2002) 253-280] detailed mechanism (565 species and 2538 reactions), over a wide range of conditions (comparable with the validity domain). The deviations between the simulated times and their fits (typically 1%) are definitely lower than the uncertainties related to the mechanism (at least 25%). In addition, using this new formalism to evaluate these durations is about 10{sup 6} times faster than simulating them with SENKIN (CHEMKIN III package) and only 10 times slower than using the classical correlations. The adaptation of the traditional method for predicting delays is interesting for modeling, because those performances are difficult to obtain simultaneously with other reduction methods (either purely mathematical, chemical, or even mixed). After a physical and mathematical justification of the proposed formalism, some of its potentialities for n-heptane combustion are presented. In particular, the trends of simulated delays and activation energies are shown for {sub T} {sub element} {sub of} {sub [1500} {sub K,1900} {sub K},} {sub P} {sub element} {sub of} {sub [10kPa,1MPa]}, X{sub Ar} element of [0,0.7], and {phi} element of {sub [0.25,4.0]}. (author)« less

A Detailed Chemical Kinetic Reaction Mechanism for n-Alkane Hydrocarbons from n-Octane to n-Hexadecane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Westbrook, C K; Pitz, W J; Herbinet, O

2007-09-25

Detailed chemical kinetic reaction mechanisms have been developed to describe the pyrolysis and oxidation of the n-alkanes, including n-octane (n-C{sub 8}H{sub 18}), n-nonane (n-C{sub 9}H{sub 20}), n-decane (n-C{sub 10}H{sub 22}), n-undecane (n-C{sub 11}H{sub 24}), n-dodecane (n-C{sub 12}H{sub 26}), n-tridecane (n-C{sub 13}H{sub 28}), n-tetradecane (n-C{sub 14}H{sub 30}), n-pentadecane (n-C{sub 15}H{sub 32}), and n-hexadecane (n-C{sub 16}H{sub 34}). These mechanisms include both high temperature and low temperature reaction pathways. The mechanisms are based on previous mechanisms for n-heptane, using the same reaction class mechanism construction developed initially for n-heptane. Individual reaction class rules are as simple as possible in order to focus onmore » the parallelism between all of the n-alkane fuels included in the mechanisms, and there is an intent to develop these mechanisms further in the future to incorporate greater levels of accuracy and predictive capability. Several of these areas for improvement are identified and explained in detail. These mechanisms are validated through comparisons between computed and experimental data from as many different sources as possible. In addition, numerical experiments are carried out to examine features of n-alkane combustion in which the detailed mechanisms can be used to compare processes in all of the n-alkane fuels. The mechanisms for all of these n-alkanes are presented as a single detailed mechanism, which can be edited to produce efficient mechanisms for any of the n-alkanes included, and the entire mechanism, with supporting thermochemical and transport data, together with an explanatory glossary explaining notations and structural details, will be available on our web page when the paper is accepted for publication.« less

A comprehensive combustion model for biodiesel-fueled engine simulations

NASA Astrophysics Data System (ADS)

Brakora, Jessica L.

Engine models for alternative fuels are available, but few are comprehensive, well-validated models that include accurate physical property data as well as a detailed description of the fuel chemistry. In this work, a comprehensive biodiesel combustion model was created for use in multi-dimensional engine simulations, specifically the KIVA3v R2 code. The model incorporates realistic physical properties in a vaporization model developed for multi-component fuel sprays and applies an improved mechanism for biodiesel combustion chemistry. A reduced mechanism was generated from the methyl decanoate (MD) and methyl-9-decenoate (MD9D) mechanism developed at Lawrence Livermore National Laboratory. It was combined with a multi-component mechanism to include n-heptane in the fuel chemistry. The biodiesel chemistry was represented using a combination of MD, MD9D and n-heptane, which varied for a given fuel source. The reduced mechanism, which contained 63 species, accurately predicted ignition delay times of the detailed mechanism over a range of engine-specific operating conditions. Physical property data for the five methyl ester components of biodiesel were added to the KIVA library. Spray simulations were performed to ensure that the models adequately reproduce liquid penetration observed in biodiesel spray experiments. Fuel composition impacted liquid length as expected, with saturated species vaporizing more and penetrating less. Distillation curves were created to ensure the fuel vaporization process was comparable to available data. Engine validation was performed against a low-speed, high-load, conventional combustion experiments and the model was able to predict the performance and NOx formation seen in the experiment. High-speed, low-load, low-temperature combustion conditions were also modeled, and the emissions (HC, CO, NOx) and fuel consumption were well-predicted for a sweep of injection timings. Finally, comparisons were made between the results of biodiesel composition (palm vs. soy) and fuel blends (neat vs. B20). The model effectively reproduced the trends observed in the experiments.

Nd2Fe14C-based magnet with better permanent magnetic properties prepared by a simple mechanochemical method

NASA Astrophysics Data System (ADS)

Geng, Hongmin; Ji, Yuan; Zhang, Jingjing; Gao, Yuchao; Yan, Yu; Wang, Wenquan; Su, Feng; Du, Xiaobo

2017-11-01

Nd2Fe14C-based magnet is prepared by a mechanochemical method, namely high-energy ball-milling Nd2Fe11Bx (x = 0-0.15) alloy in heptane (C7H16), followed by annealing to 850 °C in vacuum. Under the action of high-energy ball-milling, Nd2Fe11Bx react with heptane to form NdH2+δ, Fe-(CB), C, etc. H2 is released and Nd2Fe17, Nd2Fe17Cx (x = 0-3), Nd2Fe14C, Nd carbides and α-Fe are formed in the subsequent annealing. C amount depends on ball-milling time t. Long time ball milling or high C content suppresses the formation of 2:17 phase and favors the formation of 2:14:1 phase in the final products. Excessive ball-milling results in the quick increase of α-Fe. The maximum of magnetically hard Nd2Fe14C is obtained at t = 4 h. For Nd2Fe11 samples, there exists considerable quantity of Nd carbides and α-Fe phase appears earlier and increases rapidly with extending the ball-milling time t. The addition of B element shortens the ball-milling time of the formation of maximum Nd2Fe14C and prominently suppresses the formation of Nd carbide and α-Fe. The optimum magnetic properties, coercivity iHc of 1193.7 kA/m, remanence Mr of 580.9 kA/m, maximum magnetic energy product (BH)max of 91.7 kJ/m3 is approaching to its theoretic value of 99.2 kJ/m3 for isotropic Nd2Fe14C magnet, are obtained in Nd2Fe11B0.06 alloy ball milled for 3.5 h.

Structure and dynamics of reverse micelles containing supercooled water investigated by neutron scattering

NASA Astrophysics Data System (ADS)

Spehr, Tinka; Frick, Bernhard; Grillo, Isabelle; Falus, Peter; Müller, Martin; Stühn, Bernd

2009-03-01

We present a detailed neutron scattering study of the structure, shape fluctuations, and translational diffusion of microemulsion droplets at low temperatures. We investigate the ternary microemulsion D2O , AOT [bis(2-ethyl-hexyl) sulfosuccinate], and toluene-d8 (or heptane-d16) which forms spherical water droplets surrounded by a monolayer of AOT dispersed in oil around room temperature. At T=290K , varying the molar ratio ω of water to AOT between 3 and 12, we find using small angle neutron scattering water core radii Rc between 7 and 18Å , respectively. We characterize the structure at low temperatures down to T=220K . Upon cooling the droplet structure is maintained and Rc stays roughly constant down to temperatures where the confined water is deeply supercooled. At an ω -dependent temperature Ts we observe for all compositions a shrinking of the droplets, which depends on the initial droplet size: the smaller the initial radii, the lower the Ts is. At the lowest investigated temperature T=220K we find an ω -independent remaining water core corresponding to a number of about 2 water molecules per AOT molecule. Neutron spin-echo spectroscopy is used to monitor shape fluctuations and translational diffusion for one microemulsion ( ω=8 , Rw=12Å ) from T=300K down to temperatures below the corresponding shrinking temperature Ts . Thereby we determine the bending elasticity to be κ=0.3kBT over the whole investigated temperature range where the droplets are stable. From these results we cannot establish a link between surfactant membrane elasticity and low temperature structural instability of the droplets. Moreover, our results show that reverse AOT micelles are an excellent tool for the study of soft confined water over a broad range of confining sizes and temperatures down to the supercooled state.

Monoamine Oxidase and Dopamine β-Hydroxylase Inhibitors from the Fruits of Gardenia jasminoides

PubMed Central

Kim, Ji Ho; Kim, Gun Hee; Hwang, Keum Hee

2012-01-01

This research was designed to determine what components of Gardenia jasminoides play a major role in inhibiting the enzymes related antidepressant activity of this plant. In our previous research, the ethyl acetate fraction of G. jasminosides fruits inhibited the activities of both monoamine oxidase-A (MAO-A) and monoamine oxidase-B (MAO-B), and oral administration of the ethanolic extract slightly increased serotonin concentrations in the brain tissues of rats and decreased MAO-B activity. In addition, we found through in vitro screening test that the ethyl acetate fraction showed modest inhibitory activity on dopamine-β hydroxylase (DBH). The bioassay-guided fractionation led to the isolation of five bio-active compounds, protocatechuic acid (1), geniposide (2), 6'-O-trans-p-coumaroylgeniposide (3), 3,5-d-ihydroxy-1,7-bis (4-hydroxyphenyl) heptanes (4), and ursolic acid (5), from the ethyl acetate fraction of G. jasminoides fruits. The isolated compounds showed different inhibitory potentials against MAO-A, -B, and DBH. Protocatechuic acid showed potent inhibition against MAO-B (IC50 300 μmol/L) and DBH (334 μmol/L), exhibiting weak MAO-A inhibition (2.41 mmol/L). Two iridoid glycosides, geniposide (223 μmol/L) and 6'-O-trans-p-coumaroylgeniposide (127μmol/L), were selective MAO-B inhibitor. Especially, 6'-O-trans-p-coumaroylgeniposide exhibited more selective MAO-B inhibition than deprenyl, well-known MAO-B inhibitor for the treatment of early-stage Parkinson’s disease. The inhibitory activity of 3,5-di-hydroxy-1,7-bis (4-hydroxyphenyl) heptane was strong for MAO-B (196 μmol/L), modest for MAO-A (400 μmol/L), and weak for DBH (941 μmol/L). Ursolic acid exhibited significant inhibition of DBH (214 μmol/L), weak inhibition of MAO-B (780 μmol/L), and no inhibition against MAO-A. Consequently, G. jasminoides fruits are considerable for development of biofunctional food materials for the combination treatment of depression and neurodegenerative disorders. PMID:24116298

Computational Analysis of Spray Jet Flames

NASA Astrophysics Data System (ADS)

Jain, Utsav

There is a boost in the utilization of renewable sources of energy but because of high energy density applications, combustion will never be obsolete. Spray combustion is a type of multiphase combustion which has tremendous engineering applications in different fields, varying from energy conversion devices to rocket propulsion system. Developing accurate computational models for turbulent spray combustion is vital for improving the design of combustors and making them energy efficient. Flamelet models have been extensively used for gas phase combustion because of their relatively low computational cost to model the turbulence-chemistry interaction using a low dimensional manifold approach. This framework is designed for gas phase non-premixed combustion and its implementation is not very straight forward for multiphase and multi-regime combustion such as spray combustion. This is because of the use of a conserved scalar and various flamelet related assumptions. Mixture fraction has been popularly employed as a conserved scalar and hence used to parameterize the characteristics of gaseous flamelets. However, for spray combustion, the mixture fraction is not monotonic and does not give a unique mapping in order to parameterize the structure of spray flames. In order to develop a flamelet type model for spray flames, a new variable called the mixing variable is introduced which acts as an ideal conserved scalar and takes into account the convection and evaporation of fuel droplets. In addition to the conserved scalar, it has been observed that though gaseous flamelets can be characterized by the conserved scalar and its dissipation, this might not be true for spray flamelets. Droplet dynamics has a significant influence on the spray flamelet and because of effects such as flame penetration of droplets and oscillation of droplets across the stagnation plane, it becomes important to accommodate their influence in the flamelet formulation. In order to recognize the droplet parameters needed, a rigorous parametric study is conducted for five different parameters in both physical as well as mixing variable space. The parametric study is conducted for a counterflow setup with n-heptane and inert nitrogen on the fuel side and oxygen with inert nitrogen on the oxidizer side. The computational setup (the temperature and velocity field) is validated against the experimental data from the Yale heptane counterflow flame. The five parameters that are investigated are: aerodynamic strain rate, initial droplet diameter, number of fuel droplets, droplet velocity slip ratio and pre-vaporization ratio. It is not the first time such a study has been accomplished but not a lot of research has been done for heavier fuels such as n-heptane (a very crucial reference fuel for the octane ratings in various applications). Also parameters such as droplet slip ratio and pre-vaporization ratio have not been prudently studied in the past. It is observed that though the slip ratio is not very significant in spray flamelet characterization, the pre-vaporization ratio is important to study and has an interesting influence on spray flamelet structure. In future, based on the current parametric study, the laminar spray flamelet library can be generated which will eventually be integrated to predict turbulent spray flames.

Auto-ignition of hydrocarbons behind reflected shock waves.

NASA Technical Reports Server (NTRS)

Vermeer, D. J.; Meyer, J. W.; Oppenheim, A. K.

1972-01-01

The paper reports on the study of auto-ignition of hydrocarbon-oxygen mixtures behind reflected shock waves. Because of their bearing on the problem of knock in internal combustion engines, n-heptane and iso-octane were chosen as the combustible species. Their stoichiometric mixtures with oxygen had to be diluted with 70% argon to reduce the influence of the boundary layer. Photographic records demonstrated the existence of two different modes of ignition, as has been previously established for the hydrogen-oxygen system. The pressure-temperature limits between these regions of mild and strong ignition were determined. From the same experimental tests, induction time data were obtained over the pressure range of 1-4 atm and the temperature interval of 1200-1700 K.

HPTLC determination of diosgenin in fenugreek seeds.

PubMed

Król-Kogus, Barbara; Lamine, Khenifi Mohammed; Migas, Piotr; Boudjeniba, Messaoud; Krauze-Baranowska, Mirosława

2018-03-01

A new HPTLC-densitometric method for diosgenin determination in fenugreek seeds was established after optimization of the conditions for efficient saponin extraction and acid hydrolysis. Several procedures were tested, the best of which was a three-step Soxhlet extraction, followed by hydrolysis of the obtained methanolic extract with 2 mol L-1 H2SO4. Best diosgenin separation from other hydrolysis products was obtained on HPTLC Si60F254 plates u sing a mixture of n-heptane/ethyl acetate (7:3, V/V) and modified anisaldehyde as a spraying reagent. The method was preliminarily validated and the determined amounts of diosgenin in fenugreek seeds of Polish and African origin were found to be similar and ranged from 0.12-0.18 %.

Irreversible endo-Selective Diels–Alder Reactions of Substituted Alkoxyfurans: A General Synthesis of endo-Cantharimides

PubMed Central

Foster, Robert W; Benhamou, Laure; Porter, Michael J; Bučar, Dejan-Krešimir; Hailes, Helen C; Tame, Christopher J; Sheppard, Tom D

2015-01-01

The [4+2] cycloaddition of 3-alkoxyfurans with N-substituted maleimides provides the first general route for preparing endo-cantharimides. Unlike the corresponding reaction with 3H furans, the reaction can tolerate a broad range of 2-substitued furans including alkyl, aromatic, and heteroaromatic groups. The cycloaddition products were converted into a range of cantharimide products with promising lead-like properties for medicinal chemistry programs. Furthermore, the electron-rich furans are shown to react with a variety of alternative dienophiles to generate 7-oxabicyclo[2.2.1]heptane derivatives under mild conditions. DFT calculations have been performed to rationalize the activation effect of the 3-alkoxy group on a furan Diels–Alder reaction. PMID:25756502

Synthesis and structural, magnetic and electrochemical characterization of PtCo nanoparticles prepared by water-in-oil microemulsion

NASA Astrophysics Data System (ADS)

Solla-Gullón, J.; Gómez, Elvira; Vallés, Elisa; Aldaz, Antonio; Feliu, Juan M.

2010-05-01

PtCo nanoparticles with homogeneous size (around 3-4 nm) have been synthesized in a water-in-oil microemulsion of water/polyethylenglycol-dodecylether (BRIJ®30)/n-heptane. X-ray diffraction study revealed the formation of a cubic phase with a gradual decrease of the cell parameter with increasing cobalt incorporation in the crystalline lattice of platinum. In relation to their magnetic properties, the PtCo nanoparticles present a superparamagnetic behaviour even after annealing, although higher permeability was induced by the thermal treatment. Finally, the electrocatalytic activity of the particles towards oxalic acid oxidation in H2SO4 was evaluated. The Pt74Co26 nanoparticles showed the highest reactivity for this reaction.

Formation of porous surface layers in reaction bonded silicon nitride during processing

NASA Technical Reports Server (NTRS)

Shaw, N. J.; Glasgow, T. K.

1979-01-01

Microstructural examination of reaction bonded silicon nitride (RBSN) has shown that there is often a region adjacent to the as-nitrided surfaces that is even more porous than the interior of this already quite porous material. Because this layer of large porosity is considered detrimental to both the strength and oxidation resistance of RBSN, a study was undertaken to determine if its formation could be prevented during processing. All test bars studied were made from a single batch of Si powder which was milled for 4 hours in heptane in a vibratory mill using high density alumina cylinders as the grinding media. After air drying the powder, bars were compacted in a single acting die and hydropressed.

Combustion of liquid fuels in a flowing combustion gas environment at high pressures

NASA Technical Reports Server (NTRS)

Canada, G. S.; Faeth, G. M.

1975-01-01

The combustion of fuel droplets in gases which simulate combustion chamber conditions was considered both experimentally and theoretically. The fuel droplets were simulated by porous spheres and allowed to gasify in combustion gases produced by a burner. Tests were conducted for pressures of 1-40 atm, temperatures of 600-1500 K, oxygen concentrations of 0-13% (molar) and approach Reynolds numbers of 40-680. The fuels considered in the tests included methanol, ethanol, propanol-1, n-pentane, n-heptane and n-decane. Measurements were made of both the rate of gasification of the droplet and the liquid surface temperature. Measurements were compared with theory, involving various models of gas phase transport properties with a multiplicative correction for the effect of forced convection.

A novel antibacterial and antifungal phenolic compound from the endophytic fungus Pestalotiopsis mangiferae.

PubMed

Subban, Kamalraj; Subramani, Ramesh; Johnpaul, Muthumary

2013-01-01

A novel phenolic compound, 4-(2,4,7-trioxa-bicyclo[4.1.0]heptan-3-yl) phenol (1), was isolated from Pestalotiopsis mangiferae, an endophytic fungus associated with Mangifera indica Linn. The structure of the compound was elucidated on the basis of comprehensive spectral analysis (UV, IR, ¹H-, ¹³C- and 2D-NMR, as well as HRESI-MS). Compound (1) shows potent antibacterial and antifungal activity against Bacillus subtilis, Klebsiella pneumoniae, Escherichia coli, Micrococcus luteus, Pseudomonas aeruginosa and Candida albicans. The transmission electron microscope study for the mode of inhibition of compound (1) on bacterial pathogens revealed the destruction of bacterial cells by cytoplasm agglutination with the formation of pores in cell wall membranes.

Estimation of trace amounts of benzene in solvent-extracted vegetable oils and oil seed cakes.

PubMed

Masohan, A; Parsad, G; Khanna, M K; Chopra, S K; Rawat, B S; Garg, M O

2000-09-01

A new method is presented for the qualitative and quantitative estimation of trace amounts (up to 0.15 ppm) of benzene in crude as well as refined vegetable oils obtained by extraction with food grade hexane (FGH), and in the oil seed cakes left after extraction. The method involves the selection of two solvents; cyclohexanol, for thinning of viscous vegetable oil, and heptane, for azeotroping out trace benzene as a concentrate from the resulting mixture. Benzene is then estimated in the resulting azeotrope either by UV spectroscopy or by GC-MS subject to availability and cost effectiveness of the latter. Repeatability and reproducibility of the method is within 1-3% error. This method is suitable for estimating benzene in vegetable oils and oil seed cakes.

Soot agglomeration in isolated, free droplet combustion

NASA Technical Reports Server (NTRS)

Choi, M. Y.; Dryer, F. L.; Green, G. J.; Sangiovanni, J. J.

1993-01-01

Under the conditions of an isolated, free droplet experiment, hollow, carbonaceous structures, called soot spheres, were observed to form during the atmospheric pressure, low Reynolds number combustion of 1-methylnaphthalene. These structures which are agglomerates composed of smaller spheroidal units result from both thermophoretic effects induced by the envelope flame surrounding each drop and aerodynamic effects caused by changes in the relative gas/drop velocities. A chemically reacting flow model was used to analyze the process of sootshell formation during microgravity droplet combustion. The time-dependent temperature and gas property field surrounding the droplet was determined, and the soot cloud location for microgravity combustion of n-heptane droplets was predicted. Experiments showed that the sooting propensity of n-alkane fuel droplets can be varied through diluent substitution, oxygen-index variations, and ambient pressure reductions.

Dielectric response of asphaltene in solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sheu, E.Y.; De Tar, M.M.; Storm, D.A.

1993-12-31

Asphaltenes derived from Ratawi (Neutral Zone) crude oil, by heptane extraction, self-associate in toluene. The structure of the disperse aggregates are similar to water-in-oil microemulsion droplets. The origin of the self-association is not yet understood, but has been speculated to be related to the electric properties of asphaltenes. In this study, the authors measured the dielectric response as a function of applied frequency from 1 kHz to 10 MHz. The results suggest that the charge dynamics is confined within a spatial length scale similar to the aggregate size. This indicates that the aggregates are more conductive than the continuous (toluene)more » phase. Additionally, the authors analyzed the loss modules using the Cole-Cole equation, form which the inter-aggregate interactions were determined.« less

On the role of organic adlayers in the anomalous water sorptivity of Lépine limestone.

PubMed

Ioannou, Ioannis; Hoff, William D; Hall, Christopher

2004-11-01

Sorptivity data are reported for the capillary absorption of water, ethanol, propan-2-ol, and n-heptane by the calcitic limestone Lépine (Lavoux à grain). The data confirm that the water sorptivity is anomalously low, an indication of partial wetting by water. Results are expressed in terms of a wetting index. The water sorptivity increases after heat treatment and chemical oxidation by hydrogen peroxide bleaching, while the sorptivity with organic liquids is unchanged. These treatments, therefore, increase the water wetting index. The results provide strong evidence that the presence of a natural organic adlayer is responsible for the anomalously low water sorptivity of this particular limestone. This natural water repellency effect may be exploited in developing chemical treatments to modify the water transport properties of stone.

Evaluation of performance impairment by spacecraft contaminants

NASA Technical Reports Server (NTRS)

Geller, I.; Hartman, R. J., Jr.; Mendez, V. M.

1977-01-01

The environmental contaminants (isolated as off-gases in Skylab and Apollo missions) were evaluated. Specifically, six contaminants were evaluated for their effects on the behavior of juvenile baboons. The concentrations of contaminants were determined through preliminary range-finding studies with laboratory rats. The contaminants evaluated were acetone, methyl ethyl ketone (MEK), methyl isobutyl ketone (MIBK), trichloroethylene (TCE), heptane and Freon 21. When the studies of the individual gases were completed, the baboons were also exposed to a mixture of MEK and TCE. The data obtained revealed alterations in the behavior of baboons exposed to relatively low levels of the contaminants. These findings were presented at the First International Symposium on Voluntary Inhalation of Industrial Solvents in Mexico City, June 21-24, 1976. A preprint of the proceedings is included.

Teaching Experimental Design Using a GC MS Analysis of Cocaine on Money: A Cross-Disciplinary Laboratory 1254 Christopher A. Heimbuck and Nathan W. Bower Quantitative Determination of Nicotine and Cotinine in Urine and Sputum Using a Combined SPME-GC/MS Method

NASA Astrophysics Data System (ADS)

Witter, A. E.; Klinger, D. M.; Fan, X.; Lam, M.; Mathers, D. T.; Mabury, S. A.

2002-10-01

The forensic analysis of cocaine on currencies was optimized using a fractional, two-level experimental design that compared methanol and HCl extraction, SPE versus heptane pre-concentration, and extracted versus total ion chromatography. Subsequent student-initiated questions about levels of cocaine on U.S. and world currencies helped make connections to societal issues while teaching method optimization and chromatography. A significant correlation was found between the levels of cocaine and the age of the bills. Levels of cocaine on various world currencies followed expected drug-trafficking patterns with the highest levels found in the most developed countries.

The solvation of the ground and transition states in the reaction of ortho-palladized acetanilide with styrene in organic solvents

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sakodynskaya, I.K.; Neverov, A.A; Ryabov, A.D.

1986-07-01

The rate of the reaction of di-mu-chlorobis(acetanilidato-2C, 0) dipalladium(II) with styrene leading to 2-acetaminostilbene was found in 11 organic solvents. In all media, the reaction has second-order kinetics. The free energy, enthalpy and entropy of activation were determined in each solvent. The data for the solubility of the starting Pd(II) complex were used to determine the free energy for the transfer of the ground state of this reaction from a standard solvent (heptane) to the other solvents. The analogous transfer functions were calculated for the transition state. The correlation of the transfer functions of the starting and transition states ofmore » this reaction with empirical solvent parameters was examined.« less

Radiation-induced polymerization of cyclophosphazene trimers. Final report, 1 September 1985-30 September 1988

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stannett, V.T.

1989-01-04

Hexachlorophosphazene was irradiated in bulk and in solution after various methods of purification. When rigorously dried and purified, good yields of polymer were obtained. Poor reproducibility was found in the bulk but reasonably good results were obtained in decalin solution. The best yields and highest molecular weights were obtained after the addition of small amounts of the bulky electron acceptor pyromellitic dianhydride. Hexachlorocyclotriphosphazene was purified by recrystallization for various times from dried heptane. The trimer was then further purified by repeated sublimation steps under high vacuum. Finally the trimer was dried in the melt over rigorously baked out barium oxide.more » The monomer was then transferred to ampules or the NMR tubes for radiation and subsequent determination of the polymer content.« less

Some Results from Studies of Microwave Discharges in Liquid Heavy Hydrocarbons

NASA Astrophysics Data System (ADS)

Averin, K. A.; Lebedev, Yu. A.; Shakhatov, V. A.

2018-01-01

Some results from studies of microwave discharges in heavy hydrocarbons are presented. Microwave energy was introduced into liquid hydrocarbon via a coaxial line. The pressure above the liquid surface was equal to the atmospheric pressure. The discharge was ignited in a mixture of argon and hydrocarbon vapor. Argon was supplied through a channel in the central conductor of the coaxial line. The emission spectra of discharges in different liquid hydrocarbons were studied. It is shown that the emission spectra mainly consist of sequences of Swan bands, while radiation of other plasma components is on the noise level. Spectra of plasma emission are presented for discharges in liquid n-heptane, nefras, and C-9 oil used to produce chemical fibers. The rotational (gas) and vibrational temperatures are determined by processing the observed spectra.

Effect of high-dose irradiation on quality characteristics of ready-to-eat chicken breast

NASA Astrophysics Data System (ADS)

Yun, Hyejeong; Haeng Lee, Kyung; Jung Lee, Hyun; Woon Lee, Ju; Uk Ahn, Dong; Jo, Cheorun

2012-08-01

High-dose (higher than 30 kGy) irradiation has been used to sterilize specific-purposed foods for safe and long-term storage. The objective of this study was to investigate the effect of high-dose irradiation on the quality characteristics of ready-to-eat chicken breast in comparison with those of the low-dose irradiation. Ready-to-eat chicken breast was manufactured, vacuum-packaged, and irradiated at 0, 5, and 40 kGy. The populations of total aerobic bacteria were 4.75 and 2.26 Log CFU/g in the samples irradiated at 0 and 5 kGy, respectively. However, no viable cells were detected in the samples irradiated at 40 kGy. On day 10, bacteria were not detected in the samples irradiated at 40 kGy but the number of bacteria in the samples irradiated at 5 kGy was increased. The pH at day 0 was higher in the samples irradiated at 40 kGy than those at 0 and 5 kGy. The 2-thiobarbituric acid reactive substance (TBARS) values of the samples were not significantly different on day 0. However, on day 10, the TBARS value was significantly higher in the samples irradiated at 40 kGy than those at 0 and 5 kGy. There was no difference in the sensory scores of the samples, except for off-flavor, which was stronger in samples irradiated at 5 and 40 kGy than control. However, no difference in off-flavor between the irradiated ones was observed. After 10 days of storage, only the samples irradiated at 40 kGy showed higher off-flavor score. SPME-GC-MS analysis revealed that 5 kGy of irradiation produced 2-methylbutanal and 3-methylbutanal, which were not present in the control, whereas 40 kGy of irradiation produced hexane, heptane, pentanal, dimethly disulfide, heptanal, and nonanal, which were not detected in the control or the samples irradiated at 5 kGy. However, the amount of compounds such as allyl sulfide and diallyl disulfide decreased significantly in the samples irradiated at 5 kGy and 40 kGy.

Enantiomeric metabolic interactions and stereoselective human methadone metabolism.

PubMed

Totah, Rheem A; Allen, Kyle E; Sheffels, Pamela; Whittington, Dale; Kharasch, Evan D

2007-04-01

Methadone is administered as a racemate, although opioid activity resides in the R-enantiomer. Methadone disposition is stereoselective, with considerable unexplained variability in clearance and plasma R/S ratios. N-Demethylation of methadone in vitro is predominantly mediated by cytochrome P450 CYP3A4 and CYP2B6 and somewhat by CYP2C19. This investigation evaluated stereoselectivity, models, and kinetic parameters for methadone N-demethylation by recombinant CYP2B6, CYP3A4, and CYP2C19, and the potential for interactions between enantiomers during racemate metabolism. CYP2B6 metabolism was stereoselective. CYP2C19 was less active, and stereoselectivity was opposite that for CYP2B6. CYP3A4 was not stereoselective. With all three isoforms, enantiomer N-dealkylation rates in the racemate were lower than those of (R)-(6-dimethyamino-4,4-diphenyl-heptan-3-one) hydrochloride (R-methadone) or (S)-(6-dimethyamino-4,4-diphenyl-heptan-3-one) hydrochloride (S-methadone) alone, suggesting an enantiomeric interaction and mutual metabolic inhibition. For CYP2B6, the interaction between enantiomers was stereoselective, with S-methadone as a more potent inhibitor of R-methadone N-demethylation than R-of S-methadone. In contrast, enantiomer interactions were not stereoselective with CYP2C19 or CYP3A4. For all three cytochromes P450, methadone N-demethylation was best described by two-site enzyme models with competitive inhibition. There were minor model differences between cytochromes P450 to account for stereoselectivity of metabolism and enantiomeric interactions. Changes in plasma R/S methadone ratios observed after rifampin or troleandomycin pretreatment in humans in vivo were successfully predicted by CYP2B6- but not CYP3A4-catalyzed methadone N-demethylation. CYP2B6 is a predominant catalyst of stereoselective methadone metabolism in vitro. In vivo, CYP2B6 may be a major determinant of methadone metabolism and disposition, and CYP2B6 activity and stereoselective metabolic interactions may confer variability in methadone disposition.

A Background of a Volatile Plant Compound Alters Neural and Behavioral Responses to the Sex Pheromone Blend in a Moth.

PubMed

Dupuy, Fabienne; Rouyar, Angéla; Deisig, Nina; Bourgeois, Thomas; Limousin, Denis; Wycke, Marie-Anne; Anton, Sylvia; Renou, Michel

2017-01-01

Recognition of intra-specific olfactory signals within a complex environment of plant-related volatiles is crucial for reproduction in male moths. Sex pheromone information is detected by specific olfactory receptor neurons (Phe-ORNs), highly abundant on the male antenna. The information is then transmitted to the pheromone processing macroglomerular complex (MGC) within the primary olfactory center, the antennal lobe, where it is processed by local interneurons and projection neurons. Ultimately a behavioral response, orientation toward the pheromone source, is elicited. Volatile plant compounds (VPCs) are detected by other functional types of olfactory receptor neurons (ORNs) projecting in another area of the antennal lobe. However, Phe-ORNs also respond to some VPCs. Female-produced sex pheromones are emitted within a rich environment of VPCs, some of which have been shown to interfere with the detection and processing of sex pheromone information. As interference between the different odor sources might depend on the spatial and temporal features of the two types of stimuli, we investigated here behavioral and neuronal responses to a brief sex pheromone blend pulse in a VPC background as compared to a control background in the male noctuid moth Agrotis ipsilon . We observed male orientation behavior in a wind tunnel and recorded responses of Phe-ORNs and MGC neurons to a brief sex pheromone pulse within a background of individual VPCs. We also recorded the global input signal to the MGC using in vivo calcium imaging with the same stimulation protocol. We found that VPCs eliciting a response in Phe-ORNs and MGC neurons masked responses to the pheromone and decreased the contrast between background odor and the sex pheromone at both levels, whereas α-pinene did not interfere with first order processing. The calcium signal produced in response to a VPC background was tonic, lasting longer than the VPC stimulus duration, and masked entirely the pheromone response. One percent heptanal and linalool, in addition to the masking effect, caused a clear delay in responses of MGC neurons to the sex pheromone. Upwind flight toward the pheromone in a wind tunnel was also delayed but otherwise not altered by different doses of heptanal.

Three column intermittent simulated moving bed chromatography: 3. Cascade operation for center-cut separations.

PubMed

Jermann, Simon; Meijssen, Mattheus; Mazzotti, Marco

2015-01-23

A general design methodology for chromatographic three fraction separation by application of the three column intermittent simulated moving bed (3C-ISMB) cascade is proposed and experimentally validated by studying the purification of an intermediately retained stereoisomer of nadolol, from an equimolar mixture of its four stereoisomers. The theoretical part shows that the 3C-ISMB cascade can be easily designed by applying Triangle Theory. Moreover, a re-scaling approach for the second stage is proposed so as to account for the fact that the feed flow rates to stage 2 are generally higher as compared to stage 1 due to dilution in the latter. Scaling the columns of the second stage accordingly enables to run both stages under optimal conditions with respect to switching time and step ratio, which is an important advantage as compared to integrated ternary processes. The experimental part starts with studying the linear adsorption behavior of nadolol in heptane/ethanol/DEA on Chiralpak AD for varying ratios of heptane and ethanol. Based on that, a solvent composition of Hept/EtOH/DEA 30/70/0.3 (v/v/v) is selected and the competitive multi-component Langmuir isotherm of the quaternary mixture is determined by frontal analysis. The resulting isotherm parameters are used to design several first stage experiments aiming at removal of the most retained component. The resulting ternary intermediate product is reprocessed in several second stage experiments studying various configurations. Finally, the dilution of the intermediate product with Hept/DEA yielding a solvent composition of Hept/EtOH/DEA 60/40/0.3 (v/v/v) is examined showing that the resulting increase in retention is beneficial for final product purities. Moreover, the reduction in viscosity compensates for the dilution as it enables higher flow rates. Dilution of the intermediate product is hence the best option, yielding highest overall cascade productivity (2.10gl(-1)h(-1)) and highest product purity (97.8%) requiring a specific solvent consumption of 12l/g of product. Copyright © 2014 Elsevier B.V. All rights reserved.

Isolating the effects of reactivity stratification in reactivity-controlled compression ignition with iso-octane and n-heptane on a light-duty multi-cylinder engine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wissink, Martin L.; Curran, Scott J.; Roberts, Greg

Reactivity-controlled compression ignition (RCCI) is a dual-fuel variant of low-temperature combustion that uses in-cylinder fuel stratification to control the rate of reactions occurring during combustion. Using fuels of varying reactivity (autoignition propensity), gradients of reactivity can be established within the charge, allowing for control over combustion phasing and duration for high efficiency while achieving low NO x and soot emissions. In practice, this is typically accomplished by premixing a low-reactivity fuel, such as gasoline, with early port or direct injection, and by direct injecting a high-reactivity fuel, such as diesel, at an intermediate timing before top dead center. Both themore » relative quantity and the timing of the injection(s) of high-reactivity fuel can be used to tailor the combustion process and thereby the efficiency and emissions under RCCI. While many combinations of high- and low-reactivity fuels have been successfully demonstrated to enable RCCI, there is a lack of fundamental understanding of what properties, chemical or physical, are most important or desirable for extending operation to both lower and higher loads and reducing emissions of unreacted fuel and CO. This is partly due to the fact that important variables such as temperature, equivalence ratio, and reactivity change simultaneously in both a local and a global sense with changes in the injection of the high-reactivity fuel. This study uses primary reference fuels iso-octane and n-heptane, which have similar physical properties but much different autoignition properties, to create both external and in-cylinder fuel blends that allow for the effects of reactivity stratification to be isolated and quantified. This study is part of a collaborative effort with researchers at Sandia National Laboratories who are investigating the same fuels and conditions of interest in an optical engine. Furthermore, this collaboration aims to improve our fundamental understanding of what fuel properties are required to further develop advanced combustion modes.« less

Isolating the effects of reactivity stratification in reactivity-controlled compression ignition with iso-octane and n-heptane on a light-duty multi-cylinder engine

DOE PAGES

Wissink, Martin L.; Curran, Scott J.; Roberts, Greg; ...

2017-10-09

Reactivity-controlled compression ignition (RCCI) is a dual-fuel variant of low-temperature combustion that uses in-cylinder fuel stratification to control the rate of reactions occurring during combustion. Using fuels of varying reactivity (autoignition propensity), gradients of reactivity can be established within the charge, allowing for control over combustion phasing and duration for high efficiency while achieving low NO x and soot emissions. In practice, this is typically accomplished by premixing a low-reactivity fuel, such as gasoline, with early port or direct injection, and by direct injecting a high-reactivity fuel, such as diesel, at an intermediate timing before top dead center. Both themore » relative quantity and the timing of the injection(s) of high-reactivity fuel can be used to tailor the combustion process and thereby the efficiency and emissions under RCCI. While many combinations of high- and low-reactivity fuels have been successfully demonstrated to enable RCCI, there is a lack of fundamental understanding of what properties, chemical or physical, are most important or desirable for extending operation to both lower and higher loads and reducing emissions of unreacted fuel and CO. This is partly due to the fact that important variables such as temperature, equivalence ratio, and reactivity change simultaneously in both a local and a global sense with changes in the injection of the high-reactivity fuel. This study uses primary reference fuels iso-octane and n-heptane, which have similar physical properties but much different autoignition properties, to create both external and in-cylinder fuel blends that allow for the effects of reactivity stratification to be isolated and quantified. This study is part of a collaborative effort with researchers at Sandia National Laboratories who are investigating the same fuels and conditions of interest in an optical engine. Furthermore, this collaboration aims to improve our fundamental understanding of what fuel properties are required to further develop advanced combustion modes.« less

Cooked carrot volatiles. AEDA and odor activity comparisons. Identification of linden ether as an important aroma component.

PubMed

Buttery, Ron G; Takeoka, Gary R

2013-09-25

MS with GC-RI evidence was found for the presence of linden ether in cooked carrot (Daucus carota). Evaluation of the GC effluent from cooked carrot volatiles using aroma extract dilution analysis (AEDA) found linden ether with the highest flavor dilution (FD) factor. Others with 10-fold lower FD factors were β-ionone, eugenol, the previously unidentified β-damascenone, (E)-2-nonenal, octanal (+ myrcene), and heptanal. All other previously identified volatiles showed lower FD factors. Odor thresholds, concentrations, and odor activity values of previously identified compounds are reviewed. This indicated that at least 20 compounds occur in cooked carrots above their odor thresholds (in water). Compounds showing the highest odor activity values included β-damascenone, (E)-2-nonenal, (E,E)-2,4-decadienal, β-ionone, octanal, (E)-2-decenal, eugenol, and p-vinylguaiacol.

Skeletal Mechanism Generation of Surrogate Jet Fuels for Aeropropulsion Modeling

NASA Astrophysics Data System (ADS)

Sung, Chih-Jen; Niemeyer, Kyle E.

2010-05-01

A novel implementation for the skeletal reduction of large detailed reaction mechanisms using the directed relation graph with error propagation and sensitivity analysis (DRGEPSA) is developed and presented with skeletal reductions of two important hydrocarbon components, n-heptane and n-decane, relevant to surrogate jet fuel development. DRGEPSA integrates two previously developed methods, directed relation graph-aided sensitivity analysis (DRGASA) and directed relation graph with error propagation (DRGEP), by first applying DRGEP to efficiently remove many unimportant species prior to sensitivity analysis to further remove unimportant species, producing an optimally small skeletal mechanism for a given error limit. It is illustrated that the combination of the DRGEP and DRGASA methods allows the DRGEPSA approach to overcome the weaknesses of each previous method, specifically that DRGEP cannot identify all unimportant species and that DRGASA shields unimportant species from removal.

Polarized components of C=O vibrations Raman spectra for ethylacetate, acetone, and aggregation of molecules

NASA Astrophysics Data System (ADS)

Tukhvatullin, F. H.; Jumabaev, A.; Tashkenbaev, U. N.; Hushvaktov, H. A.; Absanov, A. A.

2002-11-01

For liquid ethylacetate the frequency maximums for parallel (I|| (v)) and perpendicular (I\\highmod(v)) polarized components of C=O vibrations band in Raman spectra are differed on 5.3 cm-1. At dilution ethylacetate in CCl4 and heptane or heating in this difference is decreased by displacement of I|| (v) maximum to the I\\highmod(v) maximum. In polar solvent, nitrometane, the picture is different - the frequency maxima difference is decreased though the displacement of I\\highmod(v) band maximum to the I|| (v)one. The results were explained by the complexity of C=O vibration bands, and existence within the band of two lines with the different depolarization ratio. The complexity of the band is the result existence in liquid ethylacetate the monomer molecules and molecular aggregations.

Protective effect of dextrans on glucose oxidase denaturation and inactivation.

PubMed

Altikatoglu, Melda; Basaran-Elalmis, Yeliz

2012-08-01

In the present study, the stabilizing effect of dextrans as additives on the denaturation and inactivation of glucose oxidase (GOD) was investigated. Three different molecular weighted dextrans (M(w) 17.5, 75, 188 kD) were used with different concentrations. Dramatically increased enzyme activities were measured after one hour of incubation of enzyme with additives between 25-40°C in water bath. Highest activity value was measured with 75 kDa molecular weighted dextran (in concentration 30% w/v) at pH 5. Dextran as an additive supplied a long shelf-life to the enzyme at 4°C. In the presence of the 75 kDa dextran, the enzyme was more stable and its activity was increased 2.7-fold at 30°C. In addition, dextran protected GOD against inactivation by a n-heptane/aqueous buffer-stirred system.

Development of a low temperature phase change material package. [for spacecraft thermal control

NASA Technical Reports Server (NTRS)

Brennan, P. J.; Suelau, H. J.; Mcintosh, R.

1977-01-01

Test data obtained for a low temperature phase change material (PCM) canisters are presented. The canister was designed to provide up to 30 w-hrs of storage capacity at approximately -90 C with an overall thermal conductance which is greater than 8 w/deg C. N-heptane which is an n-paraffin and has a -90.6 C freezing point was used as the working fluid. The canister was fabricated from aluminum and has an aluminum honeycomb core. Its void volume permits service temperatures up to 70 C. Results obtained from component and system's tests indicate well defined melting and freezing points which are repeatable and within 1 C of each other. Subcooling effects are less than 0.5 C and are essentially negligible. Measured storage capacities are within 94 to 88% the theoretical.

A new experimental method to determine the sorption isotherm of a liquid in a porous medium.

PubMed

Ouoba, Samuel; Cherblanc, Fabien; Cousin, Bruno; Bénet, Jean-Claude

2010-08-01

Sorption from the vapor phase is an important factor controlling the transport of volatile organic compounds (VOCs) in the vadose zone. Therefore, an accurate description of sorption behavior is essential to predict the ultimate fate of contaminants. Several measurement techniques are available in the case of water, however, when dealing with VOCs, the determination of sorption characteristics generally relies on gas chromatography. To avoid some drawbacks associated with this technology, we propose a new method to determine the sorption isotherm of any liquid compounds adsorbed in a soil. This method is based on standard and costless transducers (gas pressure, temperature) leading to a simple and transportable experimental device. A numerical estimation underlines the good accuracy and this technique is validated on two examples. Finally, this method is applied to determine the sorption isotherm of three liquid compounds (water, heptane, and trichloroethylene) in a clayey soil.

Spontaneous Formation of Nanopatterns in Velocity-Dependent Dip-Coated Organic Films: From Dragonflies to Stripes

NASA Astrophysics Data System (ADS)

Huber, P.; Bai, M.; Del Campo, V.; Homm, P.; Ferrari, P.; Diama, A.; Wagner, C.; Taub, H.; Knorr, K.; Deutsch, M.; Retamal, M.; Volkmann, U.; Corrales, T.

2015-11-01

We present the structure of thin, n-alkane films on the oxide layer of a silicon surface, prepared by dip-coating in a n-C32H66/n-heptane solution. Electron micrographs reveal two adsorption morphologies depending on the substrate withdrawal speed v. For small v, dragonfly-shaped molecular islands are observed. For a large v, stripes parallel to the withdrawal direction are observed. These have a few hundred micrometer lengths and a few-micrometer lateral separation. With increasing v, the surface coverage first decreases, then increases for v >vcr ~ 0 . 15 mm/s. The critical vcr marks a transition between the evaporation regime and the entrainment regime. The stripes' strong crystalline texture and the well defined separation are due to an anisotropic 2D crystallization in narrow liquid fingers, which presumably results from a Marangoni-flow-driven hydrodynamic instability in the evaporating dip-coated films.

Optimization of headspace solid phase micro-extraction of volatile compounds from papaya fruit assisted by GC-olfactometry.

PubMed

da Rocha, Renier Felinto Julião; da Silva Araújo, Ídila Maria; de Freitas, Sílvia Maria; Dos Santos Garruti, Deborah

2017-11-01

Optimization of the extraction conditions to investigate the volatile composition of papaya fruit involving headspace solid phase micro-extraction was carried out using multivariate strategies such as factorial design and response surface methodology. The performance of different combinations of time for reaching the equilibrium in the headspace and time for maximum extraction of volatiles was evaluated by GC-olfactometry of the extract (intensity of papaya characteristic aroma), number of peaks and total area in the chromatogram. Thirty-two compounds were identified by GC-MS under the optimized extraction conditions, the majority of which were aldehydes, both in number of compounds and area. Major compounds were δ-octalactone, β-citral, benzaldehyde, heptanal, benzyl isothiocyanate, isoamyl acetate, γ-octalactone, (E)-linalool oxide and benzyl alcohol. Seven aldehydes and two other compounds are reported for the first time in papaya's volatile profile.

Interfacial Force Field Characterization in a Constrained Vapor Bubble Thermosyphon

NASA Technical Reports Server (NTRS)

DasGupta, Sunando; Plawsky, Joel L.; Wayner, Peter C., Jr.

1995-01-01

Isothermal profiles of the extended meniscus in a quartz cuvette were measured in the earth's gravitational field using an image-analyzing interferometer that is based on computer-enhanced video microscopy of the naturally occurring interference fringes. These profiles are a function of the stress field. Experimentally, the augmented Young-Laplace equation is an excellent model for the force field at the solid-liquid-vapor interfaces for heptane and pentane menisci on quartz and tetradecane on SFL6. The effects of refractive indices of the solid and liquid on the measurement techniques were demonstrated. Experimentally obtained values of the disjoining pressure and dispersion constants were compared to those predicted from the Dzyaloshinskii - Lifshitz - Pilaevskii theory for an ideal surface and reasonable agreements were obtained. A parameter introduced gives a quantitative measurement of the closeness of the system to equilibrium. The nonequilibrium behavior of this parameter is also presented

Isolation of an alpha-methylene-gamma-butyrolactone derivative, a toxin from the plant pathogen Lasiodiplodia theobromae.

PubMed

He, Guochun; Matsuura, Hideyuki; Yoshihara, Teruhiko

2004-10-01

Lasiodiplodia theobromae is known as a multi-infectious microorganism that causes considerable crop damage, particularly to tropical fruits. When the fruits are infected by L. theobromae, the typical symptom is the appearance of black spots on the surface of the infected fruit. When injected in to the peel of banana, the culture filtrate of L. theobromae induced formation of black spots. The structure of the isolated compound responsible for this effect was determined to be (3S,4R)-3-carboxy-2-methylene-heptan-4-olide on the basis of analysis of MS, IR, and 1H and 13C NMR spectroscopic data, including HMQC, HMBC, and 1H-1H COSY experiments. The active compound was not only isolated from the culture filtrate derived from potato dextrose medium, but also from the extract of infected peels of bananas.

Natural and synthetic oviposition stimulants forCatolaccus grandis (Burks) females.

PubMed

Guerra, A A; Martinez, S; Sonia Del Rio, H

1994-07-01

Oviposition behavior was elicited fromCatolaccus grandis (Burks) (Hymenoptera: Pteromalidae) females, an ectoparasitoid of the boll weevil,Anthonomus grandis Boheman (Coleoptera: Curculionidae), by smears of freshly cut cotton bolls or smears of extracts prepared with boll weevil damaged or undamaged cotton boll tissues. Oviposition behavior was also elicited fromC. grandis females by smears made withn-pentane,n-hexane,n-heptane, and isooctane. This is the first report of oviposition behavior elicited for any parasitoid by these short-chain saturated hydrocarbons (alkanes), introducing a new concept on the chemical mediation of parasitoid behavior during host selection. Oviposition behavior was also elicited fromC. grandis females by volatiles emanating from an artificial diet devoid of insect components that was specifically developed for the in vitro rearing of ectoparasitoids. The possible use of a synergistic combination ofn-hexane and diet to optimize the mechanized production of noncontaminated eggs is also discussed.

[Chemical hazards when working with solvent glues].

PubMed

Domański, Wojciech; Makles, Zbigniew

2012-01-01

Solvent glues are used in a wide variety of industries, e.g., textile, footwear and rubber. The problem of workers' exposure to solvent vapors is rarely tackled within the area of occupational safety and health in small and medium-sized enterprises. In order to assess exposure to solvents, organic solvents emitted by glues were identified in the samples of workplace air. The concentration of acetone, benzene, cyclohexane, ethylbenzene, n-hexane, methylcyclohexane, butyl acetate and toluene were determined. The obtained results evidenced the presence of cyclohexane, ethylbenzene, ethylcyclohexane, heptane, n-hexane, o-xylene, methylcyclohexane, methylcyclopentane, butyl acetate and toluene in workplace air. The concentration of those compounds in workplace air was low, usually below 0.15 of MAC. At some workstations the presence of benzene was also observed. Occupational risk was assessed at workstations where gluing took place. It showed that the risk at those workstations was medium or low.

Damxungmacin A and B, Two New Amicoumacins with Rare Heterocyclic Cores Isolated from Bacillus subtilis XZ-7.

PubMed

Tang, Hui-Ling; Sun, Cheng-Hang; Hu, Xin-Xin; You, Xue-Fu; Wang, Min; Liu, Shao-Wei

2016-11-23

Two new amicoumacins, named Damxungmacin A ( 1 ) and B ( 2 ), were isolated from the culture broth of a soil-derived bacterium Bacillus subtilis XZ-7. Their chemical structures were elucidated by spectroscopic studies (UV, IR, NMR and HR-ESI-MS). Compound 1 possessed a 1,4-diazabicyclo[2.2.1]heptane-2-one ring system in its structure, which was reported for the first time, while 2 had a 1-acetylmorpholine-3-one moiety, which was naturally rare. Compound 1 exhibited moderate to weak cytotoxic activities against three human tumor cell lines (A549, HCT116 and HepG2) with IC 50 values of 13.33, 14.34 and 13.64 μM, respectively. Meanwhile, compound 1 showed weak antibacterial activities against some strains of Staphylococcus epidermidis , while compound 2 at 16 μg/mL did not show antibacterial activity.

Catalytic reduction of dinitrogen to ammonia at a single molybdenum center.

PubMed

Yandulov, Dmitry V; Schrock, Richard R

2003-07-04

Dinitrogen (N2) was reduced to ammonia at room temperature and 1 atmosphere with molybdenum catalysts that contain tetradentate [HIPTN3N]3- triamidoamine ligands (such as [HIPTN3N]Mo(N2), where [HIPTN3N]3- is [(3,5-(2,4,6-i-Pr3C6H2)2C6H3NCH2CH2)3N]3-) in heptane. Slow addition of the proton source [(2,6-lutidinium)(BAr'4), where Ar' is 3,5-(CF3)2C6H3]and reductant (decamethyl chromocene) was critical for achieving high efficiency ( approximately 66% in four turnovers). Numerous x-ray studies, along with isolation and characterization of six proposed intermediates in the catalytic reaction under noncatalytic conditions, suggest that N2 was reduced at a sterically protected, single molybdenum center that cycled from Mo(III) through Mo(VI) states.

Morphology and magnetic properties of CeCo5 submicron flakes prepared by surfactant-assisted high-energy ball milling

NASA Astrophysics Data System (ADS)

Zhang, J. J.; Gao, H. M.; Yan, Y.; Bai, X.; Su, F.; Wang, W. Q.; Du, X. B.

2012-10-01

CeCo5 permanent magnetic alloy has been processed by surfactant assisted high energy ball milling. Heptane and oleic acid were used as the solvent and surfactant, respectively. The amount of surfactant used was 50% by weight of the starting powder. The produced particles were deposited on a piece of copper (4 mm in length and width) under a magnetic field of 27 kOe applied along the copper surface and immobilized by ethyl α-cyanoacrylate. Scanning electron microscope pictures show that the particles are flakes, several μm in length and width and tens of nm in thickness. X-ray diffraction patterns and magnetic measurements prove that the flakes are crystalline with c-axes magnetic anisotropy. The easy magnetization axis is oriented perpendicular to the surface of the flake. A maximum coercivity of 3.3 kOe was obtained for the sample milled for 40 min.

Synthesis of heterocyclic analogues of epibatidine via 7-azabicyclo[2.2.1]hept-2-yl radical intermediates. 1. Intermolecular reactions.

PubMed

Gómez-Sánchez, Elena; Soriano, Elena; Marco-Contelles, José

2008-09-05

The synthesis and reactivity of the 7-azabicyclo[2.2.1]hept-2-yl radical has been extensively investigated in inter- and intramolecular reaction processes for the first time. In this work we will present the preparation of the radical and its successful intermolecular reaction with radical acceptors such as tert-butylisocyanide and acrylonitrile. Computational analyses have been carried out to show and explain the mechanisms and stereochemical outcome of these transformations. Overall and from the chemical point of view, a new and convenient synthetic approach has been developed for the synthesis of exo-2-(cyano)alkyl substituted 7-azabicyclo[2.2.1]heptane derivatives, a series of compounds of wide interest for the synthesis of heterocyclic analogues of epibatidine. As a result, we describe here the synthesis of the tetrazoloepibatidines (8 and 15) and the oxadiazoloepibatidine (10).

Defining microchannels and valves on a hydrophobic paper by low-cost inkjet printing of aqueous or weak organic solutions.

PubMed

Cai, Longfei; Zhong, Minghua; Li, Huolin; Xu, Chunxiu; Yuan, Biyu

2015-07-01

We describe a simple and cost-effective strategy for rapid fabrication of microfluidic paper-based analytical devices and valves by inkjet printing. NaOH aqueous solution was printed onto a hydrophobic filter paper, which was previously obtained by soaking in a trimethoxyoctadecylsilane-heptane solution, allowing selective wet etching of hydrophobic cellulose to create hydrophilic-hydrophobic contrast with a relatively good resolution. Hexadecyltrimethylammonium bromide (CTMAB)-ethanol solution was printed onto hydrophobic paper to fabricate temperature-controlled valves. At low temperature, CTMAB deposited on the paper is insoluble in aqueous fluid, thus the paper remains hydrophobic. At high temperature, CTMAB becomes soluble so the CTMAB-deposited channel becomes hydrophilic, allowing the wicking of aqueous solution through the valve. We believe that this strategy will be very attractive for the development of simple micro analytical devices for point-of-care applications, including diagnostic testing, food safety control, and environmental monitoring.

Novel Gas Sensor Arrays Based on High-Q SAM-Modified Piezotransduced Single-Crystal Silicon Bulk Acoustic Resonators

PubMed Central

Zhao, Yuan; Yang, Qingrui; Chang, Ye; Pang, Wei; Zhang, Hao; Duan, Xuexin

2017-01-01

This paper demonstrates a novel micro-size (120 μm × 200 μm) piezoelectric gas sensor based on a piezotransduced single-crystal silicon bulk acoustic resonator (PSBAR). The PSBARs operate at 102 MHz and possess high Q values (about 2000), ensuring the stability of the measurement. A corresponding gas sensor array is fabricated by integrating three different self-assembled monolayers (SAMs) modified PSBARs. The limit of detection (LOD) for ethanol vapor is demonstrated to be as low as 25 ppm with a sensitivity of about 1.5 Hz/ppm. Two sets of identification code bars based on the sensitivities and the adsorption energy constants are utilized to successfully discriminate isopropanol (IPA), ethanol, hexane and heptane vapors at low and high gas partial pressures, respectively. The proposed sensor array shows the potential to form a portable electronic nose system for volatile organic compound (VOC) differentiation. PMID:28672852

Novel Gas Sensor Arrays Based on High-Q SAM-Modified Piezotransduced Single-Crystal Silicon Bulk Acoustic Resonators.

PubMed

Zhao, Yuan; Yang, Qingrui; Chang, Ye; Pang, Wei; Zhang, Hao; Duan, Xuexin

2017-06-26

This paper demonstrates a novel micro-size (120 μm × 200 μm) piezoelectric gas sensor based on a piezotransduced single-crystal silicon bulk acoustic resonator (PSBAR). The PSBARs operate at 102 MHz and possess high Q values (about 2000), ensuring the stability of the measurement. A corresponding gas sensor array is fabricated by integrating three different self-assembled monolayers (SAMs) modified PSBARs. The limit of detection (LOD) for ethanol vapor is demonstrated to be as low as 25 ppm with a sensitivity of about 1.5 Hz/ppm. Two sets of identification code bars based on the sensitivities and the adsorption energy constants are utilized to successfully discriminate isopropanol (IPA), ethanol, hexane and heptane vapors at low and high gas partial pressures, respectively. The proposed sensor array shows the potential to form a portable electronic nose system for volatile organic compound (VOC) differentiation.

Verification of key odorants in rose oil by gas chromatography-olfactometry/aroma extract dilution analysis, odour activity value and aroma recombination.

PubMed

Xiao, Zuobing; Li, Jing; Niu, Yunwei; Liu, Qiang; Liu, Junhua

2017-10-01

Rose oil is much too expensive but very popular. It's well known that the flower oil's aroma profile hasn't been intensively investigated. In order to verify the aroma profile of rose oil, the synthetic blend of odorants was prepared and then compared with the original rose oil using electronic nose analysis (ENA) combined with quantitative descriptive analysis (QDA). The odorants from rose oils were screened out by Gas Chromatography-Olfactometry/aroma extract dilution analysis (GC-O/AEDA) combined with odour activity value (OAV). Both ENA and QDA indicated the recombination model derived from OAV and GC-O/AEDA closely resembled the original rose oil. The experiment results show that rose oxide, linalool, α-pinene, β-pinene, nonanal, heptanal citronellal, phenyl ethyl alcohol, benzyl alcohol, eugenol, methyl eugenol, β-citronellol, hexyl acetate, β-ionone, nerol, etc. are very important constituent to rose oil aroma profile.

A Priori Analysis of Subgrid-Scale Models for Large Eddy Simulations of Supercritical Binary-Species Mixing Layers

NASA Technical Reports Server (NTRS)

Okong'o, Nora; Bellan, Josette

2005-01-01

Models for large eddy simulation (LES) are assessed on a database obtained from direct numerical simulations (DNS) of supercritical binary-species temporal mixing layers. The analysis is performed at the DNS transitional states for heptane/nitrogen, oxygen/hydrogen and oxygen/helium mixing layers. The incorporation of simplifying assumptions that are validated on the DNS database leads to a set of LES equations that requires only models for the subgrid scale (SGS) fluxes, which arise from filtering the convective terms in the DNS equations. Constant-coefficient versions of three different models for the SGS fluxes are assessed and calibrated. The Smagorinsky SGS-flux model shows poor correlations with the SGS fluxes, while the Gradient and Similarity models have high correlations, as well as good quantitative agreement with the SGS fluxes when the calibrated coefficients are used.

Using graphene/styrene-isoprene-styrene copolymer composite thin film as a flexible microstrip antenna for the detection of heptane vapors

NASA Astrophysics Data System (ADS)

Olejnik, Robert; Matyas, Jiri; Slobodian, Petr; Riha, Pavel

2018-03-01

Most portable devices, such as mobile phones or tablets, use antennas made of copper. This paper demonstrates the possible use of antenna constructed from electrically conductive polymer composite materials for use in those applications. The method of preparation and the properties of the graphene/styrene-isoprene-styrene copolymer as flexible microstrip antenna are described in this contribution. Graphene/styrene-isoprene-styrene copolymer toluene solution was prepared by means of ultrasound and the PET substrate was dip coated to reach a fine thin film. The main advantages of using PET as a substrate are low weight and flexibility. The final size of the flexible microstrip antenna was 10 × 25 mm with thickness of 0.48 mm (PET substrate 0.25 mm) with a weight of 0.110 g. The resulting antenna operates at a frequency of 1.8 GHz and gain ‑40.02 dB.

Infrared band intensities of saturated hydrocarbons

NASA Technical Reports Server (NTRS)

Pinkley, L. W.; Sethna, P. P.; Williams, D.

1978-01-01

Kramers-Kronig analysis is applied to measured values of spectral reflectance at near-normal incidence to determine the real and the imaginary parts of the complex index of refraction for methane, ethane, propane, n-butane, n-hexane, n-heptane, and n-decane in the liquid state. The results indicate that the strengths of the characteristic bands as measured by the integral of the imaginary part are roughly constant for all the liquid alkanes except for methane. The intensity of the CH valence vibration bands in the spectra of the alkanes except methane is directly proportional to the number of CH groups per unit volume. The relations for the intensity of the bands due to CH2 and CH3 deformations are examined. Characteristic band intensities of the type established for NH4(+) and SO4(2-) groups in solutions and crystals cannot be extended to the more closely coupled CH2 and CH3 groups in alkane molecules.

QCM gas phase detection with ceramic materials--VOCs and oil vapors.

PubMed

Latif, Usman; Rohrer, Andreas; Lieberzeit, Peter A; Dickert, Franz L

2011-06-01

Titanate sol-gel layers imprinted with carbonic acids were used as sensitive layers on quartz crystal microbalance. These functionalized ceramics enable us detection of volatile organic compounds such as ethanol, n-propanol, n-butanol, n-hexane, n-heptane, n-/iso-octane, and n-decane. Variation of the precursors (i.e., tetrabutoxy titanium, tetrapropoxy titanium, tetraethoxy titanium) allows us to tune the sensitivity of the material by a factor of 7. Sensitivity as a function of precursors leads to selective inclusion of n-butanol vapors down to 1 ppm. The selectivity of materials is optimized to differentiate between isomers, e.g., n- and iso-octane. The results can be rationalized by correlating the sensor effects of hydrocarbons with the Wiener index. A mass-sensitive sensor based on titanate layer was also developed for monitoring emanation of degraded engine oil. Heating the sensor by a meander avoids vapor condensation. Thus, a continuously working oil quality sensor was designed.

Laser photolysis study of the exciplex between triplet benzil and triethylamine

DOE Office of Scientific and Technical Information (OSTI.GOV)

Encinas, M.V.; Scaiano, J.C.

1979-12-19

Nanosecond laser flash photolysis techniques have been used to examine the triplet decay and radical-ion formation in the triethylamine (TEA) - benzil system in wet acetonitrile. Under conditions of high TEA concentrations yielding short triplet lifetime, the formation of the benzil radical anion was found to be considerably slower than the decay of the triplet state. This effect is attributed to the intermediacy of a relatively stable exciplex whose properties are reported here. Results of a study of optical density of the system with time following laser excitation led to the assignment of a lifetime of 55ns to the exciplexmore » formed between the triplet benzil and TEA. A structure is suggested for the exciplex. Results of experiments with the non-polar medium n-heptane indicated a shorter lifetime exciplex or one with very different properties from the species identified in the polar medium, wet acetonitrile. (BLM)« less

Quantifying liquid boundary and vapor distributions in a fuel spray by rainbow schlieren deflectometry.

PubMed

Taber Wanstall, C; Agrawal, Ajay K; Bittle, Joshua A

2017-10-20

The rainbow schlieren deflectometry (RSD) technique is used to determine the liquid boundary and the fuel volume fraction distributions in the vapor region of a high-pressure fuel spray. Experiments were conducted in a constant pressure flow vessel, whereby a customized single-hole common-rail diesel injector is used to introduce n-heptane fuel into a coflow of low-speed ambient air at two different test conditions. Only the quasi-steady period of the fuel spray is considered, and multiple injections are performed to acquire statistically significant data at an image acquisition rate of 20 kHz. An algorithm to identify the liquid boundary using intensity recorded by the RSD images is presented. The results are compared against measurements obtained by the Mie scattering technique. Results demonstrate that the RSD can be a powerful optical diagnostics technique to simultaneously quantify both the vapor and liquid regions in the high-pressure fuel sprays.

Low gravity synthesis of polymers with controlled molecular configuration

NASA Technical Reports Server (NTRS)

Heimbuch, A. H.; Parker, J. A.; Schindler, A.; Olf, H. G.

1975-01-01

Heterogeneous chemical systems have been studied for the synthesis of isotactic polypropylene in order to establish baseline parameters for the reaction process and to develop sensitive and accurate methods of analysis. These parameters and analytical methods may be used to make a comparison between the polypropylene obtained at one g with that of zero g (gravity). Baseline reaction parameters have been established for the slurry (liquid monomer in heptane/solid catalyst) polymerization of propylene to yield high purity, 98% isotactic polypropylene. Kinetic data for the slurry reaction showed that a sufficient quantity of polymer for complete characterization can be produced in a reaction time of 5 min; this time is compatible with that available on a sounding rocket for a zero-g simulation experiment. The preformed (activated) catalyst was found to be more reproducible in its activity than the in situ formed catalyst.

A Study of Aircraft Fire Hazards Related to Natural Electrical Phenomena

NASA Technical Reports Server (NTRS)

Kester, Frank L.; Gerstein, Melvin; Plumer, J. A.

1960-01-01

The problems of natural electrical phenomena as a fire hazard to aircraft are evaluated. Assessment of the hazard is made over the range of low level electrical discharges, such as static sparks, to high level discharges, such as lightning strikes to aircraft. In addition, some fundamental work is presented on the problem of flame propagation in aircraft fuel vent systems. This study consists of a laboratory investigation in five parts: (1) a study of the ignition energies and flame propagation rates of kerosene-air and JP-6-air foams, (2) a study of the rate of flame propagation of n-heptane, n-octane, n-nonane, and n-decane in aircraft vent ducts, (3) a study of the damage to aluminum, titanium, and stainless steel aircraft skin materials by lightning strikes, (4) a study of fuel ignition by lightning strikes to aircraft skins, and (5) a study of lightning induced flame propagation in an aircraft vent system.

Hydrocarbons identified in extracts from estuarine water accommodated no. 2 fuel oil by gas chromatography-mass spectrometry

NASA Technical Reports Server (NTRS)

Lewis, B. W.; Walker, A. L.; Bieri, R. H.

1974-01-01

Results are presented on a computerized gas chromatograph-mass spectrometer analysis of methylene chloride and n-heptane extracts of a No. 2 fuel oil accommodated estuarine water sample. The analytical method is briefly described, and the limitations on the identifications are categorized. Some attempt was made to determine major and trace constituents in the water accommodate. Altogether 66 hydrocarbon compounds were identified specifically, and 75 compounds were partially identified. Seven compounds could be recognized as major constituents of the water accommodated oil and ten were present only as traces. The aromatic compounds found were alkyl benzenes, naphthalene, tetralin, indane, biphenyl, fluorene, anthracene, and some of their alkyl substituted isomers in the range of carbon numbers C7 to C15. Four n-alkanes, C10 to C13, were found along with four other assorted hydrocarbons.

Predicting the oral uptake efficiency of chemicals in mammals: Combining the hydrophilic and lipophilic range

DOE Office of Scientific and Technical Information (OSTI.GOV)

O'Connor, Isabel A., E-mail: i.oconnor@science.ru.nl; Huijbregts, Mark A.J., E-mail: m.huijbregts@science.ru.nl; Ragas, Ad M.J., E-mail: a.ragas@science.ru.nl

Environmental risk assessment requires models for estimating the bioaccumulation of untested compounds. So far, bioaccumulation models have focused on lipophilic compounds, and only a few have included hydrophilic compounds. Our aim was to extend an existing bioaccumulation model to estimate the oral uptake efficiency of pollutants in mammals for compounds over a wide K{sub ow} range with an emphasis on hydrophilic compounds, i.e. compounds in the lower K{sub ow} range. Usually, most models use octanol as a single surrogate for the membrane and thus neglect the bilayer structure of the membrane. However, compounds with polar groups can have different affinitiesmore » for the different membrane regions. Therefore, an existing bioaccumulation model was extended by dividing the diffusion resistance through the membrane into an outer and inner membrane resistance, where the solvents octanol and heptane were used as surrogates for these membrane regions, respectively. The model was calibrated with uptake efficiencies of environmental pollutants measured in different mammals during feeding studies combined with human oral uptake efficiencies of pharmaceuticals. The new model estimated the uptake efficiency of neutral (RMSE = 14.6) and dissociating (RMSE = 19.5) compounds with logK{sub ow} ranging from − 10 to + 8. The inclusion of the K{sub hw} improved uptake estimation for 33% of the hydrophilic compounds (logK{sub ow} < 0) (r{sup 2} = 0.51, RMSE = 22.8) compared with the model based on K{sub ow} only (r{sup 2} = 0.05, RMSE = 34.9), while hydrophobic compounds (logK{sub ow} > 0) were estimated equally by both model versions with RMSE = 15.2 (K{sub ow} and K{sub hw}) and RMSE = 15.7 (K{sub ow} only). The model can be used to estimate the oral uptake efficiency for both hydrophilic and hydrophobic compounds. -- Highlights: ► A mechanistic model was developed to estimate oral uptake efficiency. ► Model covers wide logK{sub ow} range (- 10 to + 8) and several mammalian species. ► K{sub ow} and the heptane water partition coefficient K{sub hw} were combined. ► K{sub ow} and K{sub hw} reflect the inner and the outer membrane diffusion resistance. ► Combining K{sub ow} and K{sub hw} improved uptake estimation for hydrophilic compounds.« less

Investigation of Sooting in Microgravity Droplet Combustion: Fuel-Dependent Effects

NASA Technical Reports Server (NTRS)

Manzello, Samuel L.; Hua, Ming; Choi, Mun Young

1999-01-01

Kumagai and coworkers first performed microgravity droplet combustion experiments [Kumagai, 1957]. The primary goal of these early experiments were to validate simple 'd(sup 2)-law models [Spalding, 1954, Godsave, 1954] Inherent in the 'd(sup 2) -law' formulation and in the scope of the experimental observation is the neglect of sooting behavior. In fact, the influence of sooting has not received much attention until more recent works [Choi et al., 1990; Jackson et al., 1991; Jackson and Avedisian, 1994; Choi and Lee, 1996; Jackson and Avedisian, 1996; Lee et al., 1998]:. Choi and Lee measured soot volume fraction for microgravity droplet flames using full-field light extinction and subsequent tomographic inversion [Choi and Lee, 1996]. In this investigation, soot concentrations were measured for heptane droplets and it was reported that soot concentrations were considerably higher in microgravity compared to the normal gravity flame. It was reasoned that the absence of buoyancy and the effects of thermophoresis resulted in the higher soot concentrations. Lee et al. [1998] performed soot measurement experiments by varying the initial droplet diameter and found marked influence of sooting on the droplet burning behavior. There is growing sentiment that sooting in droplet combustion must no longer be neglected and that "perhaps one of the most important outstanding contributions of (micro)g droplet combustion is the observation that in the absence of asymmetrical forced and natural convection, a soot shell is formed between the droplet surface and the flame, exerting an influence on the droplet combustion response far greater than previously recognized." [Law and Faeth, 1994]. One of the methods that we are exploring to control the degree of sooting in microgravity is to use different fuels. The effect of fuel structure on sooting propensity has been investigated for over-ventilated concentric coflowing buoyant diffusion flames. (Glassman, 1996]. In these investigations, the fuel flowrate was increased until smoke was observed to escape from the "luminous visible flame" [Glassman, 1996]. A total of 29 fuels were used in order to characterize relative sooting propensity. The sooting propensity of a particular fuel was assessed by comparing the flowrates for soot emission from the tip of the flame. It was reported that the sooting tendency for diffusion flames increased for fuels with higher rates of pyrolysis. Randolph and Law [1986 and not 1994] also examined the effect of fuel structure on droplet sooting behavior. In their experiments the droplets were separated from the bulk gas stream and quenched with nitrogen prior to gravimetric measurements. A variety of fuels were studied, namely aromatics, phenyl-alkanes and alkanes. The results were in qualitative agreement with the work of Glassman [1986]. Vander Wal et al. [1994] performed relative soot concentration measurements using laser-induced incandescence for heptane and decane fuel droplets burning under normal-gravity conditions. It was found that soot volume fractions for decane was more than a factor of two larger than that for heptane. Although the normal-gravity investigations have provided some important insights regarding the influence of fuel structure on the sooting behavior of droplet flames, results cannot be easily extrapolated for microgravity studies since increased residence times and thermophoretic effects must be considered in greater detail. Several studies have compared sooting behavior of different fuel droplets burning under microgravity conditions [Card and Choi, 1990; Jackson et al., 1991; Jackson and Avedisian, 1994], however, detailed quantitative results were not provided. In all of these previous studies, the degree of sooting was only visually assessed from an incandescent backlighted image of the soot containing region. Such techniques can provide misleading results regarding sooting behavior [Choi, 1996].

Occurrence of diverse alkane hydroxylase alkB genes in indigenous oil-degrading bacteria of Baltic Sea surface water.

PubMed

Viggor, Signe; Jõesaar, Merike; Vedler, Eve; Kiiker, Riinu; Pärnpuu, Liis; Heinaru, Ain

2015-12-30

Formation of specific oil degrading bacterial communities in diesel fuel, crude oil, heptane and hexadecane supplemented microcosms of the Baltic Sea surface water samples was revealed. The 475 sequences from constructed alkane hydroxylase alkB gene clone libraries were grouped into 30 OPFs. The two largest groups were most similar to Pedobacter sp. (245 from 475) and Limnobacter sp. (112 from 475) alkB gene sequences. From 56 alkane-degrading bacterial strains 41 belonged to the Pseudomonas spp. and 8 to the Rhodococcus spp. having redundant alkB genes. Together 68 alkB gene sequences were identified. These genes grouped into 20 OPFs, half of them being specific only to the isolated strains. Altogether 543 diverse alkB genes were characterized in the brackish Baltic Sea water; some of them representing novel lineages having very low sequence identities with corresponding genes of the reference strains. Copyright © 2015 Elsevier Ltd. All rights reserved.

Droplet size effects on NO/x/ formation in a one-dimensional monodisperse spray combustion system

NASA Technical Reports Server (NTRS)

Sarv, H.; Nizami, A. A.; Cernansky, N. P.

1982-01-01

A one-dimensional monodisperse aerosol spray combustion facility is described and experimental results of post flame NO/NO(x) emissions are presented. Four different hydrocarbon fuels were studied: isopropanol, methanol, n-heptane, and n-octane. The results indicate an optimum droplet size in the range of 48-58 microns for minimizing NO/NO(x) production for all of the test fuels. This NO(x) behavior is associated with droplet interactions and the transition from diffusive type of spray burning to that of a prevaporized and premixed case. Decreasing the droplet size results in a trend of increasing droplet interactions, which suppresses temperatures and reduces NO(x). This trend continues until prevaporization effects begin to dominate and the system tends towards the premixed limit. The occurrence of the minimum NO(x) point at different droplet diameters for the different fuels appears to be governed by the extent of prevaporization of the fuel in the spray, and is consistent with theoretical calculations based on each fuel's physical properties.

Quantifying liquid boundary and vapor distributions in a fuel spray by rainbow schlieren deflectometry

DOE Office of Scientific and Technical Information (OSTI.GOV)

Taber Wanstall, C.; Agrawal, Ajay K.; Bittle, Joshua A.

The rainbow schlieren deflectometry (RSD) technique is used to determine the liquid boundary and the fuel volume fraction distributions in the vapor region of a high-pressure fuel spray. Experiments were conducted in a constant pressure flow vessel, whereby a customized single-hole common-rail diesel injector is used to introduce n-heptane fuel into a coflow of low-speed ambient air at two different test conditions. Only the quasi-steady period of the fuel spray is considered, and multiple injections are performed to acquire statistically significant data at an image acquisition rate of 20 kHz. An algorithm to identify the liquid boundary using intensity recordedmore » by the RSD images is presented. The results are compared against measurements obtained by the Mie scattering technique. Our results demonstrate that the RSD can be a powerful optical diagnostics technique to simultaneously quantify both the vapor and liquid regions in the high-pressure fuel sprays.« less

The gas phase structure of α -pinene, a main biogenic volatile organic compound

NASA Astrophysics Data System (ADS)

Neeman, Elias M.; Avilés Moreno, Juan Ramón; Huet, Thérèse R.

2017-12-01

The gas phase structure of the bicyclic atmospheric aerosol precursor α-pinene was investigated employing a combination of quantum chemical calculation and Fourier transform microwave spectroscopy coupled to a supersonic jet expansion. The very weak rotational spectra of the parent species and all singly substituted 13C in natural abundance have been identified, from 2 to 20 GHz, and fitted to Watson's Hamiltonian model. The rotational constants were used together with geometrical parameters from density functional theory and ab initio calculations to determine the rs, r0, and rm(1 ) structures of the skeleton, without any structural assumption in the fit concerning the heavy atoms. The double C=C bond was found to belong to a quasiplanar skeleton structure containing 6 carbon atoms. Comparison with solid phase structure is reported. The significant differences of α-pinene in gas phase and other gas phase bicyclic monoterpene structures (β-pinene, nopinone, myrtenal, and bicyclo[3.1.1]heptane) are discussed.

Solution and Solid State Nuclear Magnetic Resonance Spectroscopic Characterization of Efavirenz.

PubMed

Sousa, Eduardo Gomes Rodrigues de; Carvalho, Erika Martins de; San Gil, Rosane Aguiar da Silva; Santos, Tereza Cristina Dos; Borré, Leandro Bandeira; Santos-Filho, Osvaldo Andrade; Ellena, Javier

2016-09-01

Samples of efavirenz (EFZ) were evaluated to investigate the influence of the micronization process on EFZ stability. A combination of X-ray diffraction, thermal analysis, FTIR, observations of isotropic chemical shifts of (1)H in distinct solvents, their temperature dependence and spin-lattice relaxation time constants (T1), solution (1D and 2D) (13)C nuclear magnetic resonance (NMR), and solid-state (13)C NMR (CPMAS NMR) provides valuable structural information and structural elucidation of micronized EFZ and heptane-recrystallized polymorphs (EFZ/HEPT). This study revealed that the micronization process did not affect the EFZ crystalline structure. It was observed that the structure of EFZ/HEPT is in the same form as that obtained from ethyl acetate/hexane, as shown in the literature. A comparison of the solid-state NMR spectra revealed discrepancies regarding the assignments of some carbons published in the literature that have been resolved. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Simultaneous determination of phenylephrine hydrochloride, guaifenesin, and chlorpheniramine maleate in cough syrup by gradient liquid chromatography.

PubMed

Amer, Sawsan M; Abbas, Samah S; Shehata, Mostafa A; Ali, Nahed M

2008-01-01

A simple and reliable high-performance liquid chromatographic method was developed for the simultaneous determination of mixture of phenylephrine hydrochloride (PHENYL), guaifenesin (GUAIF), and chlorpheniramine maleate (CHLO) either in pure form or in the presence of methylparaben and propylparaben in a commercial cough syrup dosage form. Separation was achieved on a C8 column using 0.005 M heptane sulfonic acid sodium salt (pH 3.4 +/- 0.1) and acetonitrile as a mobile phase by gradient elution at different flow rates, and detection was done spectrophotometrically at 210 nm. A linear relationship in the range of 30-180, 120-1800, and 10-60 microg/mL was obtained for PHENYL, GUAIF, and CHLO, respectively. The results were statistically analyzed and compared with those obtained by applying the British Pharmacopoeia (2002) method and showed that the proposed method is precise, accurate, and can be easily applied for the determination of the drugs under investigation in pure form and in cough syrup formulations.

Irreversible endo-selective diels-alder reactions of substituted alkoxyfurans: a general synthesis of endo-cantharimides.

PubMed

Foster, Robert W; Benhamou, Laure; Porter, Michael J; Bučar, Dejan-Krešimir; Hailes, Helen C; Tame, Christopher J; Sheppard, Tom D

2015-04-13

The [4+2] cycloaddition of 3-alkoxyfurans with N-substituted maleimides provides the first general route for preparing endo-cantharimides. Unlike the corresponding reaction with 3H furans, the reaction can tolerate a broad range of 2-substitued furans including alkyl, aromatic, and heteroaromatic groups. The cycloaddition products were converted into a range of cantharimide products with promising lead-like properties for medicinal chemistry programs. Furthermore, the electron-rich furans are shown to react with a variety of alternative dienophiles to generate 7-oxabicyclo[2.2.1]heptane derivatives under mild conditions. DFT calculations have been performed to rationalize the activation effect of the 3-alkoxy group on a furan Diels-Alder reaction. © 2015 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA. This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumar, Kamal; Zhang, Yu; Sung, Chi -Jen

We study the influence of blending n-butanol on the ignition delay times of n-heptane and iso-octane, the primary reference fuels for gasoline. The ignition delay times are measured using a rapid compression machine, with an emphasis on the low-to-intermediate temperature conditions. The experiments are conducted at equivalence ratios of 0.4 and 1.0, for a compressed pressure of 20 bar, with the temperatures at the end of compression ranging from 613 K to 979 K. The effect of n-butanol addition on the development of the two-stage ignition characteristics for the two primary reference fuels is also examined. The experimental results aremore » compared to predictions obtained using a detailed chemical kinetic mechanism, which has been obtained by a systematic merger of previously reported base models for the combustion of the individual fuel constituents. In conclusion, a sensitivity analysis on the base, and the merged models, is also performed to understand the dependence of autoignition delay times on the model parameters.« less

Water evaporation in silica colloidal deposits.

PubMed

Peixinho, Jorge; Lefèvre, Grégory; Coudert, François-Xavier; Hurisse, Olivier

2013-10-15

The results of an experimental study on the evaporation and boiling of water confined in the pores of deposits made of mono-dispersed silica colloidal micro-spheres are reported. The deposits are studied using scanning electron microscopy, adsorption of nitrogen, and adsorption of water through attenuated total reflection-infrared spectroscopy. The evaporation is characterized using differential scanning calorimetry and thermal gravimetric analysis. Optical microscopy is used to observe the patterns on the deposits after evaporation. When heating at a constant rate and above boiling temperature, the release of water out of the deposits is a two step process. The first step is due to the evaporation and boiling of the surrounding and bulk water and the second is due to the desorption of water from the pores. Additional experiments on the evaporation of water from membranes having cylindrical pores and of heptane from silica deposits suggest that the second step is due to the morphology of the deposits. Copyright © 2013 Elsevier Inc. All rights reserved.

1996 PAMS hydrocarbon QA studies in EPA Region II: Part II. Trends and insights

DOE Office of Scientific and Technical Information (OSTI.GOV)

Teitz, A.; Kantz, M.

1997-12-31

Comparison of ambient air samples between EPA Region II and the PAMS monitoring organizations within the Region, and comparisons among EPA Regions I, II, and III, revealed the following analytical trends: (1) Agreement between laboratories was typically between 10-20% for many of the PAMS analytes found at higher concentrations, i.e., butane, isopentane, benzene, toluene, and m/p-xylene; (2) Nafion dryer systems tended to underestimate the amount of acetylene by 35-50%; (3) Isobutylene co-elution with 1-butene proved difficult to resolve unless a 100 meter DB-1 or a regular length PLOT GC column was used; (4) Organizations that monitor for polar compounds foundmore » that co-elution of ethanol/acetone can interfere with the analysis of 1-pentene; (5) Analytical systems capable of polar analyses can have co-elution and/or misidentification of these aldehydes, typically in the styrene/heptanal/o-xylene regions of the chromatogram; and (6) Tetrachloroethylene was found to interfere with octane quantitation in some analyses.« less

Determination of urinary 6-mercaptopurine and three of its metabolites by HPLC-UV coupled with the iodine-azide reaction.

PubMed

Zakrzewski, Robert; Borowczyk, Kamila; Łuczak, Adam; Młynarski, Wojciech; Trelińska, Joanna

2013-04-01

The presented method is able to determine 6-mercaptopurine (6-MP), 6-thioguanine, 6-mercaptopurine riboside and 6-thioguanine riboside in urine, and is thereby dedicated to control of thiopurine therapy of children with acute lymphoblastic leukemia. Good separation of the mentioned compounds was achieved on a C18 stationary phase with a sodium azide and sodium heptane sulfonate solution, acetonitrile and water at ratio of 50:1:49 (v/v/v). Coefficient of regression is >0.99 for all linearity ranges. LOD and LOQ are 0.3, 0.4, 0.3, 0.8 and 0.4, 0.6, 0.5 and 0.9 nmol/ml of urine for 6-MP, 6-thioguanine, 6-mercaptopurine riboside and 6-thioguanine riboside, respectively. Intra- and inter-day recovery and RSD are close to 100% and less than 10%, respectively, for all investigated thiopurines. The elaborated method was successfully applied for detection and quantitation of 6-MP and its selected metabolites in patients' urine samples.

Alphatic 3,4-epoxyalcohols. Metabolism by epoxide hydrase and mutagenic activity.

PubMed

Ortiz de Montellano, P R; Boparai, A S

1978-12-18

Rabbit hepatic microsomal epoxide hydrase catalyzes the rapid hydrolysis of 1,2-epoxy-4-heptanol to 1,2,4-heptanetriol. Both diastereomers of the substrate are hydrolyzed, and both product diastereomers are formed. Similarly both cis- and trans-3,4-epoxy-1-hexanol are hydrolyzed, albeit more slowly, to give 1,3,4-hexanetriol. The trans isomer gives exclusively one diastereomer (erythro) of the triol, while the cis isomer gives the other diastereomer (threo). The product expected if a primary cationic intermediate were to be formed and trapped intramolecularly during the hydrolysis of 1,2-epoxy-4-heptanol, 2-propyl-4-tetrahydrofuranol, was not observed. A comparison of the mutagenic activity in the Ames test of 1-heptane, 1-hepten-4-ol, 1,2-epoxyheptane, and 1,2-epoxy-4-heptanol revealed that only the latter is a detectable mutagen. A vicinal hydroxyl therefore does not interfere significantly with enzymatic epoxide hydrolysis, but it does enhance the bioalkylating potential of even an aliphatic epoxide.

Decreasing luminescence lifetime of evaporating phosphorescent droplets

NASA Astrophysics Data System (ADS)

van der Voort, D. D.; Dam, N. J.; Sweep, A. M.; Kunnen, R. P. J.; van Heijst, G. J. F.; Clercx, H. J. H.; van de Water, W.

2016-12-01

Laser-induced phosphorescence has been used extensively to study spray dynamics. It is important to understand the influence of droplet evaporation in the interpretation of such measurements, as it increases luminescence quenching. By suspending a single evaporating n-heptane droplet in an acoustic levitator, the properties of lanthanide-complex europium-thenoyltrifluoroacetone-trioctylphosphine oxide (Eu-TTA-TOPO) phosphorescence are determined through high-speed imaging. A decrease was found in the measured phosphorescence decay coefficient (780 → 200 μs) with decreasing droplet volumes (10-9 → 10-11 m3) corresponding to increasing concentrations (10-4 → 10-2 M). This decrease continues up to the point of shell-formation at supersaturated concentrations. The diminished luminescence is shown not to be attributable to triplet-triplet annihilation, quenching between excited triplet-state molecules. Instead, the pure exponential decays found in the measurements show that a non-phosphorescent quencher, such as free TTA/TOPO, can be attributable to this decay. The concentration dependence of the phosphorescence lifetime can therefore be used as a diagnostic of evaporation in sprays.

Flavor and Acceptance of Roasted California Almonds During Accelerated Storage.

PubMed

Franklin, Lillian M; King, Ellena S; Chapman, Dawn; Byrnes, Nadia; Huang, Guangwei; Mitchell, Alyson E

2018-02-07

Monitoring oxidative flavor changes in almonds is possible only if the chemical and sensory profile during roasting and storage is first established. Herein, almonds roasted at two different temperatures (115 and 152 °C) were stored at 39 °C for 0 to 12 months and were analyzed by headspace solid-phase microextraction gas chromatography-mass spectrometry, descriptive analysis, and consumer hedonic analysis. Volatile profiles, descriptive sensory profiles, and consumer hedonic scores were analyzed for predictive relationships. Descriptive attributes involving Roasted and Nutty as well as consumer liking were highest in fresh almonds, while flavors typically associated with oxidative rancidity such as Cardboard, Painty/Solvent, Soapy, and Total Oxidized increased during storage. Compounds most important for predicting rancidity-related attributes were lipid oxidation products, including pentanal, hexanal, heptanal, and octanal. Consumer liking was best predicted by similar compounds to those predicting Clean Nutty flavor, including Maillard reaction products such as 2- and 3-methylbutanal, 2-methylpyrazine, and 2,5-dimethylpyrazine.

Cheese milk low homogenization enhanced early lipolysis and volatiles compounds production in hard cooked cheeses.

PubMed

Vélez, María A; Hynes, Erica R; Meinardi, Carlos A; Wolf, Verónica I; Perotti, María C

2017-06-01

Homogenization applied to cheese milk has shown to increase lipolysis but its use is not spread as it can induce detrimental effects. The aim of this work was to assess the effect of low-pressure homogenization of the cream followed by pre-incubation of cheese milk on the composition, ripening index, lipolysis and volatile profiles of hard cooked cheeses. For that, control and experimental miniature Reggianito cheeses were made and analyzed during ripening (3, 45 and 90days). Homogenization had no impact on composition and proteolysis. An acceleration of the lipolysis reaction was clearly noticed in cheeses made with homogenized milk at the beginning of ripening, while both type of cheeses reached similar levels at 90days. We found the level of several compounds derived from fatty acid catabolism were noticeably influenced by the treatment applied: straight-chain aldehydes such as hexanal, heptanal and nonanal and methylketones from C 5 to C 9 were preferentially formed in experimental cheeses. Copyright © 2017 Elsevier Ltd. All rights reserved.

Short-chain alkanes synergise responses of moth pests to their sex pheromones.

PubMed

Gurba, Alexandre; Guerin, Patrick M

2016-05-01

The use of sex pheromones for mating disruption of moth pests of crops is increasing worldwide. Efforts are under way to augment the efficiency and reliability of this control method by adding molecules derived from host plants to the sex attractants in dispensers. We show how attraction of the European grapevine moth, Lobesia botrana Den. & Schiff., and the codling moth, Cydia pomonella L., males to underdosed levels of their sex pheromones is increased by adding heptane or octane over a range of release rates. Pheromone-alkane mixtures enhance male recruitment by up to 30%, reaching levels induced by calling females, and shorten the flight time to the sex attractant by a factor of 2. The findings show the promise of using short-chain alkanes as pheromone synergists for mating disruption of insect pests of food crops. Alkane-pheromone combinations are expected to increase the competitiveness of dispensers with females, and to reduce the amount of pheromone needed for the control of these pests. © 2015 Society of Chemical Industry.

Synthesis, anti-HIV activity studies, and in silico rationalization of cyclobutane-fused nucleosides.

PubMed

Figueras, Antoni; Miralles-Llumà, Rosa; Flores, Ramon; Rustullet, Albert; Busqué, Félix; Figueredo, Marta; Font, Josep; Alibés, Ramon; Maréchal, Jean-Didier

2012-06-01

The present work describes some recent approaches to novel 3-oxabicyclo[3.2.0]heptane-type nucleosides structurally similar to the potent anti-HIV agent stavudine (d4T). To gain knowledge at the molecular level relevant for further synthetic designs, the lack of activity of these compounds was investigated by computational approaches accounting for three main physiological requirements of anti-HIV nucleosides: their drug-likeness, their activation process, and their subsequent interaction with HIV reverse transcriptase (HIV-RT). Our results show that the inclusion of the fused cyclobutane at the 2'- and 3'-positions of the sugar portion provides drug-like compounds. Nonetheless, the presence of this cyclobutane moiety prevents binding orientations consistent with the catalytic activation for at least one of the enzymes known to activate d4T. To the best of our knowledge, this is the first study to explicitly consider the simulation of the entire activation process to rationalize anti-HIV activities. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Viscosities of nonelectrolyte liquid mixtures. III. Selected binary and quaternary mixtures

NASA Astrophysics Data System (ADS)

Wakefield, D. L.

1988-05-01

This paper is the final in a series of three viscosity and density studies of pure n-alkanes and selected binary and quaternary mixtures. A standard U-tube viscometer was used for viscosity measurements, and a Pyrex flask-type pycnometer was used for density determinations. Results are given here for pure alkane and selected binary mixtures of n-tetradecane + n-octane, for selected quaternary mixtures of n-hexadecane + n-dodecane + n-decane + n-hexane, and for pure and selected quaternary mixtures of n-hexadecane + n-dodecane + n-nonane + n-heptane at 303.16 and 308.16 K. The principle of congruence was tested, as was the Grunberg and Nissan equation, as they have been shown to be useful as prediction techniques for other n-alkane binary mixtures. Comparisons were made between the two groups of quaternary alkane mixtures and the binary n-tetradecane + n-octane mixtures of the same “pseudo” composition to understand better the dependence of mixture viscosities on the composition parameter.

One-step isolation of γ-oryzanol from rice bran oil by non-aqueous hydrostatic countercurrent chromatography.

PubMed

Angelis, Apostolis; Urbain, Aurélie; Halabalaki, Maria; Aligiannis, Nektarios; Skaltsounis, Alexios-Leandros

2011-09-01

The value-added γ-oryzanol was purified in one step from crude rice bran oil (RBO) using a preparative hydrostatic countercurrent chromatography (hydrostatic CCC) method, operating in the dual mode. The fractionation was performed using a non-aqueous biphasic solvent system consisting of heptane-acetonitrile-butanol (1.8:1.4:0.7, v/v/v), leading rapidly to the target compounds. Transfer of the analytical CCC method to large-scale isolation was also carried out yielding a high quantity-high purity fraction of γ-oryzanol. In addition, a fraction of hydroxylated triterpene alcohol ferulates (polar γ-oryzanol) was clearly separated and obtained. Furthermore, a fast HPLC-APCI(±)-HRMS method was developed and applied for the identification of γ-oryzanol as well as the polar γ-oryzanol in RBO and the resulting fractions. The purity of γ-oryzanol fraction was estimated as 97% based on HPLC-APCI-HRMS analysis. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fuel droplet burning rates at high pressures

NASA Technical Reports Server (NTRS)

Canada, G. S.; Faeth, G. M.

1972-01-01

Combustion of methanol, ethanol, propanol -1, n - pentane, n - heptane and n - decane was observed in air under natural convection conditions at pressures up to 100 atm. The droplets were simulated by porous spheres with diameters in the range 0.63 - 1.90 cm. The pressure levels of the tests were high enough so that near critical combustion was observed for methanol and ethanol. Measurements were made of the burning rate and liquid surface temperatures of the fuels. The data were compared with variable property analysis of the combustion process, including a correction for natural convection. The burning rate predictions of the various theories were similar and in fair agreement with the data. The high pressure theory gave the best prediction for the liquid surface temperatures of ethanol and propanol -1 at high pressure. The experiments indicated the approach of critical burning conditions for methanol and ethanol at pressures on the order of 80 - 100 atm, which was in good agreement with the predictions of both the low and high pressure analysis.

Supercooling of water confined in reverse micelles

NASA Astrophysics Data System (ADS)

Spehr, T.; Frick, B.; Grillo, I.; Stühn, B.

2008-03-01

We report on the temperature dependence of the nanosecond-timescale dynamics of the ternary mixture water/AOT/oil with deuterated heptane, toluene or decane as the oil. Water-swollen reverse micelles as formed in such microemulsions allow us to investigate the freezing behaviour of water confined in a soft environment. We report here on the first neutron scattering studies in which the freezing of the confined water and of the oil is followed down to temperatures at which the whole system is frozen. We focus on studies of water confined in three different droplet sizes: by means of small-angle neutron scattering we have determined the radii to be 46, 18, and 7 Å for water to surfactant ratios ω = 40, 12, and 3. From elastic temperature scans by neutron backscattering we deduce a strong supercooling of water confined in the reverse swollen micelles which increases with decreasing droplet size. For the smallest droplets we find a supercooling of more than 45 K compared to bulk water.

Molecular dynamics study of oil adsorption on the rock surface in presence of silica nanoparticles

NASA Astrophysics Data System (ADS)

Salehzadeh, Jamal; Tohidi, Zahra; Jafari, Arezou

2018-01-01

Despite the increasing applications of nanoparticles in enhanced oil recovery (EOR), there is not enough information about the mechanisms and microscopic aspects of nanoparticles' effects. Therefore, in this research, molecular dynamics simulation is used to provide the molecular-scale insight for investigation of the silica nanoparticles effects on the oil adsorption on calcite surface for the first time. The surface interacts with the mixture of heptane and decane as the oil phase with mole ratio of 1/2 and silica nanoparticles are dispersed in distilled water with concentration of 7000 ppm. Based on the simulation results, by using nanoparticles surface adsorption behavior have been changed to hydrophilic and the oil molecules departed from the calcite. This result is based on the oil-calcite binding energy calculation which is decreased from 5224 kcal/mol to 3278 kcal/mol by using silica nanoparticles. In addition, calculation of radial distribution functions showed that after adding silica nanoparticles, the picks fall which means increasing in average distance between oil and calcite surface.

Some aspects of TLC in homogenous magnetic fields.

PubMed

Malinowska, Irena; Studziński, Marek; Malinowski, Henryk

2011-08-01

This article consists of two parts. First part is a short review about the role of magnetic phenomena in natural environment, human surroundings, and his activities such as science, engineering, and medicine. The second part of the article presents a set of experiments, their results, and data obtained in a static homogenous magnetic field, generated by a pair of permanent magnets and outside it. Adsorption chromatographic systems were investigated: as chromatographed substances - polyaromatic hydrocarbon (PAH), as stationary phase - silica gel 60, as monocomponent mobile phases - n-hexane, n-heptane, n-octane, and benzene were used and binary mobile phases n-hydrocarbons - benzene. Magnetic field influences retention and efficiency of investigated chromatographic systems. Experimental data analysis (RF, N) allows us to propose some explanations of the differences between experiment results performed in induced magnetic field and outside it, and in consequence on the changes in the interfacial phenomena induced by field presence. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Determination of solubility parameters of high density polyethylene by inverse gas chromatography].

PubMed

Wang, Qiang; Chen, Yali; Liu, Ruiting; Shi, Yuge; Zhang, Zhengfang; Tang, Jun

2011-11-01

Inverse gas chromatographic (IGC) technology was used to determine the solubility parameters of high density polyethylene (HDPE) at the absolute temperatures from 303.15 to 343.15 K. Six solvents were applied as test probes including hexane (n-C6), heptane (n-C7), octane (n-C8), nonane (n-C9), chloroform (CHCl3) and ethyl acetate (EtAc). Some thermodynamic parameters were obtained by IGC data analysis such as the specific retention volumes of the solvents (V(0)(g)), the molar enthalpy of sorption (delta H(S)(1)), the partial molar enthalpy of mixing at infinite dilution (delta H(1)(infinity)), the molar enthalpy of vaporization (delta H(v)), the activity coefficients at infinite dilution (omega (1)(infinity)), and Flow-Huggins interaction parameters (X(1,2)(infinity)) between HDPE and probe solvents. The results showed that the above six probes are poor solvents for HDPE. The solubility parameter of HDPE at room temperature (298.15 K) was also derived as 19.00 (J/cm3)(0.5).

UV photochemistry of carboxylic acids at the air-sea boundary: A relevant source of glyoxal and other oxygenated VOC in the marine atmosphere

NASA Astrophysics Data System (ADS)

Chiu, R.; Tinel, L.; Gonzalez, L.; Ciuraru, R.; Bernard, F.; George, C.; Volkamer, R.

2017-01-01

Photochemistry plays an important role in marine dissolved organic carbon (DOC) degradation, but the mechanisms that convert DOC into volatile organic compounds (VOCs) remain poorly understood. We irradiated carboxylic acids (C7-C9) on a simulated ocean surface with UV light (<320 nm) in a photochemical flow reactor and transferred the VOC products into a dark ozone reactor. Glyoxal was detected as a secondary product from heptanoic, octanoic, and nonanoic acid (NA) films, but not from octanol. Primary glyoxal emissions were not observed, nor was glyoxal formed in the absence of ozone. Addition of a photosensitizer had no noticeable effect. The concurrent detection of heptanal in the NA system suggests that the ozonolysis of 2-nonenal is the primary chemical mechanism that produces glyoxal. This source can potentially sustain tens of parts per trillion by volume (pptv) glyoxal over oceans, and helps to explain why glyoxal fluxes in marine air are directed from the atmosphere into the ocean.

A HPLC method for the quantification of butyramide and acetamide at ppb levels in hydrogeothermal waters

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gracy Elias; Earl D. Mattson; Jessica E. Little

A quantitative analytical method to determine butyramide and acetamide concentrations at the low ppb levels in geothermal waters has been developed. The analytes are concentrated in a preparation step by evaporation and analyzed using HPLC-UV. Chromatographic separation is achieved isocratically with a RP C-18 column using a 30 mM phosphate buffer solution with 5 mM heptane sulfonic acid and methanol (98:2 ratio) as the mobile phase. Absorbance is measured at 200 nm. The limit of detection (LOD) for BA and AA were 2.0 {mu}g L{sup -1} and 2.5 {mu}g L{sup -1}, respectively. The limit of quantification (LOQ) for BA andmore » AA were 5.7 {mu}g L{sup -1} and 7.7 {mu}g L{sup -1}, respectively, at the detection wavelength of 200 nm. Attaining these levels of quantification better allows these amides to be used as thermally reactive tracers in low-temperature hydrogeothermal systems.« less

An experimental study of high-pressure droplet combustion

NASA Technical Reports Server (NTRS)

Norton, Chris M.; Litchford, Ron J.; Jeng, San-Mou

1990-01-01

The results are presented of an experimental study on suspended n-heptane droplet combustion in air for reduced pressures up to P(r) = 2.305. Transition to fully transient heat-up through the critical state is demonstrated above a threshold pressure corresponding to P(r) of roughly 1.4. A silhouette imaging technique resolves the droplet surface for reduced pressures up to about P(r) roughly 0.63, but soot formation conceals the surface at higher pressures. Images of the soot plumes do not show any sudden change in behavior indicative of critical transition. Mean burning rate constants are computed from the d-squared variation law using measured effective droplet diameters at ignition and measured burn times, and corrected burning times are computed for an effective initial droplet diameter. The results show that the burning rates increase as the fuel critical pressure is approached and decrease as the pressure exceeds the fuel critical pressure. Corrected burning times show inverse behavior.

Temperature- and pressure-dependent absorption cross sections of gaseous hydrocarbons at 3.39 µm

NASA Astrophysics Data System (ADS)

Klingbeil, A. E.; Jeffries, J. B.; Hanson, R. K.

2006-07-01

The pressure- and temperature-dependent absorption cross sections of several neat hydrocarbons and multi-component fuels are measured using a 3.39 µm helium-neon laser. Absorption cross section measurements are reported for methane, ethylene, propane, n-heptane, iso-octane, n-decane, n-dodecane, JP-10, gasoline and jet-A with an estimated uncertainty of less than 3.5%. The experimental conditions range from 298 to 673 K and from 500 to 2000 Torr with nitrogen as the bath gas. An apparatus is designed to facilitate these measurements, and specific care is taken to ensure the compositional accuracy of the hydrocarbon/N2 mixtures. The absorption cross sections of the smallest hydrocarbons, methane and ethylene, vary with temperature and pressure. The cross sections of larger hydrocarbons show negligible dependence on pressure and only a weak dependence on temperature. The reported data increase the range of conditions and the number of hydrocarbons for which cross section measurements are available at the HeNe laser wavelength.

Quantifying liquid boundary and vapor distributions in a fuel spray by rainbow schlieren deflectometry

DOE PAGES

Taber Wanstall, C.; Agrawal, Ajay K.; Bittle, Joshua A.

2017-01-01

The rainbow schlieren deflectometry (RSD) technique is used to determine the liquid boundary and the fuel volume fraction distributions in the vapor region of a high-pressure fuel spray. Experiments were conducted in a constant pressure flow vessel, whereby a customized single-hole common-rail diesel injector is used to introduce n-heptane fuel into a coflow of low-speed ambient air at two different test conditions. Only the quasi-steady period of the fuel spray is considered, and multiple injections are performed to acquire statistically significant data at an image acquisition rate of 20 kHz. An algorithm to identify the liquid boundary using intensity recordedmore » by the RSD images is presented. The results are compared against measurements obtained by the Mie scattering technique. Our results demonstrate that the RSD can be a powerful optical diagnostics technique to simultaneously quantify both the vapor and liquid regions in the high-pressure fuel sprays.« less

Measurements of C6-C8 hydrocarbons at a UK rural site during January 1999. Site evaluation and correlations between species.

PubMed

Hopkins, J R; Barnett, C J; Lewis, A C; Seakins, P W

2003-02-01

Ambient concentrations of C6-C8 aromatic hydrocarbons and n-heptane, determined by gas chromatography with flame ionisation detection, are presented from a winter campaign during January 1999 at a rural site near Leeds. Absolute concentrations are significantly lower than those obtained from the only designated UK rural site (Harwell) in the automated UK hydrocarbon network. Both absolute and relative concentrations of hydrocarbons measured at the site have been interpreted in terms of the arriving back-trajectories. The site is subject to two main airflows during the winter months; relatively polluted air from the southwest and much cleaner air from the northwest. Ratios of hydrocarbon concentrations show evidence of significant chemical processing consistent with chemical removal by OH. Uncertainties in the ages of the trajectories prevent a reliable estimation of the average OH concentration over the trajectory. The dependence of the variance of the hydrocarbon concentrations with their lifetime with respect to removal by OH does not show the expected behaviour.

Carbon-Carbon Bond Formation and Hydrogen Production in the Ketonization of Aldehydes.

PubMed

Orozco, Lina M; Renz, Michael; Corma, Avelino

2016-09-08

Aldehydes possess relatively high chemical energy, which is the driving force for disproportionation reactions such as Cannizzaro and Tishchenko reactions. Generally, this energy is wasted if aldehydes are transformed into carboxylic acids with a sacrificial oxidant. Here, we describe a cascade reaction in which the surplus energy of the transformation is liberated as molecular hydrogen for the oxidation of heptanal to heptanoic acid by water, and the carboxylic acid is transformed into potentially industrially relevant symmetrical ketones by ketonic decarboxylation. The cascade reaction is catalyzed by monoclinic zirconium oxide (m-ZrO2 ). The reaction mechanism has been studied through cross-coupling experiments between different aldehydes and acids, and the final symmetrical ketones are formed by a reaction pathway that involves the previously formed carboxylic acids. Isotopic studies indicate that the carboxylic acid can be formed by a hydride shift from the adsorbed aldehyde on the metal oxide surface in the absence of noble metals. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Phase Behavior of a Single Structured Ionomer Chain in Solution

DOE PAGES

Aryal, Dipak; Etampawala, Thusitha; Perahia, Dvora; ...

2014-08-14

Structured polymers offer a means to tailor transport pathways within mechanically stable manifolds. Here we examine the building block of such a membrane, namely a single large pentablock co-polymer that consist of a center block of a randomly sulfonated polystyrene, designed for transport, tethered to poly-ethylene-r-propylene and end-capped by poly-t-butyl styrene, for mechanical stability,using molecular dynamics simulations. The polymer structure in a cyclohexane-heptane mixture, a technologically viable solvent, and in water, a poor solvent for all segments and a ubiquitous substance is extracted. In all solvents the pentablock collapsed into nearly spherical aggregates where the ionic block is segregated. Inmore » hydrophobic solvents, the ionic block resides in the center, surrounded by swollen intermix of flexible and end blocks. In water all blocks are collapsed with the sulfonated block residing on the surface. Our results demonstrate that solvents drive different local nano-segregation, providing a gateway to assemble membranes with controlled topology.« less

Validation of an All-Pressure Fluid Drop Model: Heptane Fluid Drops in Nitrogen

NASA Technical Reports Server (NTRS)

Harstad, K.; Bellan, J.; Bulzan, Daniel L. (Technical Monitor)

2000-01-01

Despite the fact that supercritical fluids occur both in nature and in industrial situations, the fundamentals of their behavior is poorly understood because supercritical fluids combine the characteristics of both liquids and gases, and therefore their behavior is not intuitive. There are several specific reasons for the lack of understanding: First, data from (mostly optical) measurements can be very misleading because regions of high density thus observed are frequently identified with liquids. A common misconception is that if in an experiment one can optically identify "drops" and "ligaments", the observed fluid must be in a liquid state. This inference is incorrect because in fact optical measurements detect any large change (i.e. gradients) in density. Thus, the density ratio may be well below Omicron(10(exp 3)) that characterizes its liquid/gas value, but the measurement will still identify a change in the index of refraction providing that the change is sudden (steep gradients). As shown by simulations of supercritical fluids, under certain conditions the density gradients may remain large during the supercritical binary fluids mixing, thus making them optically identifiable. Therefore, there is no inconsistency between the optical observation of high density regions and the fluids being in a supercritical state. A second misconception is that because a fluid has a liquid-like density, it is appropriate to model it as a liquid. However, such fluids may have liquid-like densities while their transport properties differ from those of a liquid. Considering that the critical pressure of most fuel hydrocarbons used in Diesel and gas turbine engines is in the range of 1.5 - 3 MPa, and the fact that the maximum pressure attained in these engines is about 6 Mps, it is clear that the fuel in the combustion chamber will experience both subcritical and supercritical conditions. Studies of drop behavior over a wide range of pressures were performed in the past, however none of these studies identified the crucial differences between the subcritical and supercritical behavior. In fact, in two of these studies, it was found that the subcritical and supercritical behavior is similar as the drop diameter decreased according to the classical d(exp 2)-law over a wide range of pressures and drop diameters. The present study is devoted to the exploration of differences in fluid-behavior characteristics under subcritical and supercritical conditions in the particular case of heptane fluid drops in nitrogen; these substances were selected because of the availability of experimental observations for model validation.

Opposed Jet Burner Extinction Limits: Simple Mixed Hydrocarbon Scramjet Fuels vs Air

NASA Technical Reports Server (NTRS)

Pellett, Gerald L.; Vaden, Sarah N.; Wilson, Lloyd G.

2007-01-01

Opposed Jet Burner tools have been used extensively by the authors to measure Flame Strength (FS) of laminar non-premixed H2 air and simple hydrocarbon (HC) air counterflow diffusion flames at 1-atm. FS represents a strain-induced extinction limit based on air jet velocity. This paper follows AIAA-2006-5223, and provides new HC air FSs for global testing of chemical kinetics, and for characterizing idealized flameholding potentials during early scramjet-like combustion. Previous FS data included six HCs, pure and N2-diluted; and three HC-diluted H2 fuels, where FS decayed very nonlinearly as HC was added to H2, due to H-atom scavenging. This study presents FSs on mixtures of (candidate surrogate) HCs, some with very high FS ethylene. Included are four binary gaseous systems at 300 K, and a hot ternary system at approx. 600 K. The binaries are methane + ethylene, ethane + ethylene, methane + ethane, and methane + propylene. The first three also form two ternary systems. The hot ternary includes both 10.8 and 21.3 mole % vaporized n-heptane and full ranges of methane + ethylene. Normalized FS data provide accurate means of (1) validating, globally, chemical kinetics for extinction of non-premixed flames, and (2) estimating (scaling by HC) the loss of incipient flameholding in scramjet combustors. The n-heptane is part of a proposed baseline simulant (10 mole % with 30% methane + 60% ethylene) that mimics the ignition of endothermically cracked JP-7 like kerosene fuel, as suggested by Colket and Spadaccini in 2001 in their shock tube Scramjet Fuels Autoignition Study. Presently, we use FS to gauge idealized flameholding, and define HC surrogates. First, FS was characterized for hot nheptane + methane + ethylene; then a hot 36 mole % methane + 64% ethylene surrogate was defined that mimics FS of the baseline simulant system. A similar hot ethane + ethylene surrogate can also be defined, but it has lower vapor pressure at 300 K, and thus exhibits reduced gaseous capacity. The new FS results refine our earlier idealized reactivity scale that shows wide ranging (50 x) diameter-normalized FSs for various HCs. These range from JP-10 and methane to H2 air, which produces an exceptionally strong flame that agrees within approx. 1% of recent 2-D numerically simulations. Finally, we continue advocating the FS approach as more direct and fundamental, for assessing idealized scramjet flameholding potentials, than measurements of unstrained laminar burning velocity or blowout in a Perfectly Stirred Reactor.

Residency of rhenium and osmium in a heavy crude oil

NASA Astrophysics Data System (ADS)

DiMarzio, Jenna M.; Georgiev, Svetoslav V.; Stein, Holly J.; Hannah, Judith L.

2018-01-01

Rhenium-osmium (Re-Os) isotope geochemistry is an emerging tool for the study of oil formation and migration processes, and a new technology for petroleum exploration. Little is known, however, about the residency of Re and Os within asphaltene and maltene sub-fractions of crude oil. This information is crucial for understanding the 187Re-187Os radiometric clock held in petroleum systems and for interpreting geochronology for key processes such as oil formation, migration, and biodegradation. In this study, a heavy crude oil was separated into soluble (maltene, MALT) and insoluble (asphaltene, ASPH) fractions using n-heptane as the asphaltene-precipitating agent. The asphaltenes were separated sequentially into sub-fractions using two different solvent pairs (heptane-dichloromethane and acetone-toluene), and the bulk maltenes were separated into saturate, aromatic, and resin (SAR) fractions using open column chromatography. Each asphaltene and maltene sub-fraction was analyzed for Re and Os. The asphaltene sub-fractions and the bulk ASPH, MALT, and crude oil were analyzed for a suite of trace metals by ICP-MS. Our results show that Re and Os concentrations co-vary between the asphaltene sub-fractions, and that both elements are found mostly in the more polar and aromatic sub-fractions. Significant Re and Os are also present in the aromatic and resin fractions of the maltenes. However, each asphaltene and maltene sub-fraction has a distinct isotopic composition, and sub-fractions are not isochronous. This suggests that asphaltene sub-fractionation separates Re-Os complexes to the point where the isotopic integrity of the geochronometer is compromised. The mobility of individual Re and Os isotopes and the decoupling possibilities between radiogenic 187Os produced from 187Re remain elusive, but their recognition in this study is a critical first step. Re and Os correlate strongly with Mo and Cd in the asphaltene sub-fractions, suggesting that these metals occupy similar sites. Re-Os and Ni-V budgets also show some similarities, indicating that at least some Re (and possibly Os) could be present in metalloporphyrin form. We conclude that progressive asphaltene precipitation during migration and mixing of oils can change the isotopic ratios of the resultant oil. A sense of process is key to interpretation of Re-Os data for tar mats and live oils, whether isochronous or scattered datasets result. Optimally, by combining data from source rocks, oils, and asphaltenes generated along the migration pathway, we can construct temporal histories for whole petroleum systems.

Transitional phase inversion of emulsions monitored by in situ near-infrared spectroscopy.

PubMed

Charin, R M; Nele, M; Tavares, F W

2013-05-21

Water-heptane/toluene model emulsions were prepared to study emulsion transitional phase inversion by in situ near-infrared spectroscopy (NIR). The first emulsion contained a small amount of ionic surfactant (0.27 wt % of sodium dodecyl sulfate) and n-pentanol as a cosurfactant. In this emulsion, the study was guided by an inversion coordinate route based on a phase behavior study previously performed. The morphology changes were induced by rising aqueous phase salinity in a "steady-state" inversion protocol. The second emulsion contained a nonionic surfactant (ethoxylated nonylphenol) at a concentration of 3 wt %. A continuous temperature change induced two distinct transitional phase inversions: one occurred during the heating of the system and another during the cooling. NIR spectroscopy was able to detect phase inversion in these emulsions due to differences between light scattered/absorbed by water in oil (W/O) and oil in water (O/W) morphologies. It was observed that the two model emulsions exhibit different inversion mechanisms closely related to different quantities of the middle phases formed during the three-phase behavior of Winsor type III.

Correlation of Chemical and Physical Test Data for the Environmental Ageing of Tefzel (ETFE)

NASA Technical Reports Server (NTRS)

Morgan, G. J.; Campion, R. P.

1996-01-01

In a similar approach to that used for the previously issued correlation report for Coflon (CAPP/M.10), this report aims to identify any correlations between mechanical property changes and chemical/morphological changes for Tefzel, using information supplied in other MERL and TRI project reports (plus latest data which will be included in final reports for Phase 1). Differences identified with Coflon behaviour will be of scientific interest as well as appropriate to project applications, as Tefzel and Coflon are chemical isomers. Owing to the considerable chemical resistance of Tefzel, much of its testing so far has been based on mechanical properties. Where changes have occurred, chemical analysis can now be targeted more effectively. Relevant test data collated here include: tensile modulus and related properties, permeation coefficients, % crystallinity, and other observations where significant. Fluids based on methanol and amine (Fluid G), a mixture of methane, carbon dioxide and hydrogen sulphide gases plus an aqueous amine solution (Fluid F), and an aromatic oil mix of heptane, cyclohexane, toluene and I-propanol (Fluid 1) have affected Tefzel to varying degrees, and are discussed in some detail herein.

Correlation of Chemical and Physical Test Data for the Environmental Ageing of Tefzel (ETFE). Revised

NASA Technical Reports Server (NTRS)

Morgan, G. J.; Campion, R. P.

1997-01-01

In a similar approach to that used for the previously issued correlation report for Coflon (CAPP/M.10), this report aims to identify any correlations between mechanical property changes and chemical/morphological changes for Tefzel, using information supplied in other MERL and TRI project reports. Differences identified with Coflon behaviour will be of scientific interest as well as appropriate to project applications, as Tefzel and Coflon are chemical isomers. Owing to the considerable chemical resistance of Tefzel, much of its testing so far has been based on mechanical properties. Where changes have occurred, chemical analysis can now be targeted more effectively. Relevant test data collated here include: tensile modulus and related properties, permeation coefficients, % crystallinity, some crack growth resistance measurements, and other observations where significant. Fluids based on methanol and amine (Fluid G), a mixture of methane, carbon dioxide and hydrogen sulphide gases plus an aqueous amine solution (Fluid F), and an aromatic oil mix of heptane, cyclohexane, toluene and 1-propanol (Fluid I) have affected Tefzel to varying degrees, and are discussed in some detail herein.

Effects of diamines on ornithine decarboxylase activity in control and virally transformed mouse fibroblasts.

PubMed Central

Bethell, D R; Pegg, A E

1979-01-01

1. The induction of ornithine decarboxylase activity in mouse 3T3 fibroblasts or an SV-40 transformed 3T3 cell line by serum was prevented by addition of the naturally occurring polyamines putrescine (butane-1,4-diamine) and spermidine. Much higher concentrations of these amines were required to fully suppress ornithine decarboxylase activity in the transformed SV-3T3 cells than in the 3T3 fibroblasts. 2. Synthetic alpha omega-diamines with 3--12 carbon atoms also prevented the increase in ornithine decarboxylase activity induced by serum in these cells. The longer chain diamines were somewhat more potent than propane-1,3-diamine in this effect, but the synthetic diamines were less active than putrescine in the 3T3 cells. There was little difference between the responses of 3T3 and SV-3T3 cells to the synthetic diamines propane-1,3-diamine and heptane-1,7-diamine. 3. These results are discussed in relation to the control of polyamine synthesis in mammalian cells. PMID:486108

Effects of Fuel Laminar Flame Speed Compared to Engine Tumble Ratio, Ignition Energy, and Injection Strategy on Lean and EGR Dilute Spark Ignition Combustion

DOE PAGES

Kolodziej, Christopher P.; Pamminger, Michael; Sevik, James; ...

2017-03-28

Previously we show that fuels with higher laminar flame speed also have increased tolerance to EGR dilution. In this work, the effects of fuel laminar flame speed on both lean and EGR dilute spark ignition combustion stability were examined. Fuels blends of pure components (iso-octane, n-heptane, toluene, ethanol, and methanol) were derived at two levels of laminar flame speed. Each fuel blend was tested in a single-cylinder spark-ignition engine under both lean-out and EGR dilution sweeps until the coefficient of variance of indicated mean effective pressure increased above thresholds of 3% and 5%. The relative importance of fuel laminar flamemore » speed to changes to engine design parameters (spark ignition energy, tumble ratio, and port vs. direct injection) was also assessed. Our results showed that fuel laminar flame speed can have as big an effect on lean or EGR dilute engine operation as engine design parameters, with the largest effects seen during EGR dilute operation and when changes were made to cylinder charge motion.« less

Schinus terebinthifolius countercurrent chromatography (Part III): Method transfer from small countercurrent chromatography column to preparative centrifugal partition chromatography ones as a part of method development.

PubMed

das Neves Costa, Fernanda; Hubert, Jane; Borie, Nicolas; Kotland, Alexis; Hewitson, Peter; Ignatova, Svetlana; Renault, Jean-Hugues

2017-03-03

Countercurrent chromatography (CCC) and centrifugal partition chromatography (CPC) are support free liquid-liquid chromatography techniques sharing the same basic principles and features. Method transfer has previously been demonstrated for both techniques but never from one to another. This study aimed to show such a feasibility using fractionation of Schinus terebinthifolius berries dichloromethane extract as a case study. Heptane - ethyl acetate - methanol -water (6:1:6:1, v/v/v/v) was used as solvent system with masticadienonic and 3β-masticadienolic acids as target compounds. The optimized separation methodology previously described in Part I and II, was scaled up from an analytical hydrodynamic CCC column (17.4mL) to preparative hydrostatic CPC instruments (250mL and 303mL) as a part of method development. Flow-rate and sample loading were further optimized on CPC. Mobile phase linear velocity is suggested as a transfer invariant parameter if the CPC column contains sufficient number of partition cells. Copyright © 2017 Elsevier B.V. All rights reserved.

Influence of different environments on the excited-state proton transfer and dual fluorescence of fisetin

NASA Astrophysics Data System (ADS)

Guharay, Jayanti; Dennison, S. Moses; Sengupta, Pradeep K.

1999-05-01

The influence of different protic and aprotic solvent environments on the excited-state intramolecular proton transfer (ESIPT) leading to a dual fluorescence behaviour of a biologically important, naturally occurring, polyhydroxyflavone, fisetin (3,3',4',7-tetrahydroxyflavone), has been investigated. The normal fluorescence band, in particular, is extremely sensitive to solvent polarity with νmax shifting from 24 510 cm -1 in dioxane ( ET(30)=36.0) to 20 790 cm -1 in methanol ( ET(30)=55.5). This is rationalized in terms of solvent dipolar relaxation process, which also accounts for the red edge excitation shifts (REES) observed in viscous environments such as glycerol at low temperatures. Significant solvent dependence of the tautomer fluorescence properties ( νmax, yield and decay kinetics) reveals the influence of external hydrogen bonding perturbation on the internal hydrogen bond of the molecule. These excited-state relaxation phenomena and their relevant parameters have been used to probe the microenvironment of fisetin in a membrane mimetic system, namely AOT reverse micelles in n-heptane at different water/surfactant molar ratio ( w0).

Effects of pressure fluctuations on the combustion process in turbulent premixed flames

NASA Astrophysics Data System (ADS)

Beardsell, Guillaume; Lapointe, Simon; Blanquart, Guillaume

2016-11-01

The need for a thorough understanding of turbulence-combustion interactions in compressible flows is driven by recent technological developments in propulsion as well as renewed interest in the development of next generation supersonic and hypersonic vehicles. In such flows, pressure fluctuations displaying a wide range of length and timescales are present. These fluctuations are expected to impact the combustion process to varying degrees, depending amongst other things on the amplitude of the pressure variations and the timescales of the chemical reactions taking place in the flame. In this context, numerical simulations of these flows can provide insight into the impact of pressure fluctuations on the combustion process. In the present work, we analyze data from simulations of statistically-flat premixed n-heptane/air flames at high Karlovitz numbers. The compressible Navier-Stokes equations are solved exactly (DNS) and results obtained with both detailed kinetic modeling and one-step chemistry are considered. The effects of pressure fluctuations on the fuel burning rate are investigated. The findings are compared with results obtained from simulations of one-dimensional premixed flames subjected to various pressure waves.

Effects of Fuel Laminar Flame Speed Compared to Engine Tumble Ratio, Ignition Energy, and Injection Strategy on Lean and EGR Dilute Spark Ignition Combustion

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kolodziej, Christopher P.; Pamminger, Michael; Sevik, James

Previously we show that fuels with higher laminar flame speed also have increased tolerance to EGR dilution. In this work, the effects of fuel laminar flame speed on both lean and EGR dilute spark ignition combustion stability were examined. Fuels blends of pure components (iso-octane, n-heptane, toluene, ethanol, and methanol) were derived at two levels of laminar flame speed. Each fuel blend was tested in a single-cylinder spark-ignition engine under both lean-out and EGR dilution sweeps until the coefficient of variance of indicated mean effective pressure increased above thresholds of 3% and 5%. The relative importance of fuel laminar flamemore » speed to changes to engine design parameters (spark ignition energy, tumble ratio, and port vs. direct injection) was also assessed. Our results showed that fuel laminar flame speed can have as big an effect on lean or EGR dilute engine operation as engine design parameters, with the largest effects seen during EGR dilute operation and when changes were made to cylinder charge motion.« less

Initial Observations on the Burning of an Ethanol Droplet in Microgravity

NASA Technical Reports Server (NTRS)

Kazakov, Andrei; Urban, Bradley; Conley, Jordan; Dryer, Frederick L.; Ferkul, Paul (Technical Monitor)

1999-01-01

Combustion of liquid ethanol represents an important system both from fundamental and practical points of view, Ethanol is currently being used as an additive to gasoline in order to reduce carbon monoxide and particulate emissions as well as to improve the fuel octane rating. A detailed physical understanding of liquid ethanol combustion is therefore necessary to achieve an optimal performance of such fuel blends in practical conditions. Ethanol is also a relatively simple model compound suitable for investigation of important combustion characteristics typical of more complex fuels. In particular, ethanol has been proposed for studies of sooting behavior during droplet burning. The sooting nature of ethanol has pressure sensitivities similar to that of n-heptane, but shifted to a higher range of pressures (1-3 atm). Additionally, liquid ethanol is miscible with water produced during its combustion forming mixtures with azeotropic behavior, a phenomenon important for understanding multi-component, liquid fuel combustion. In this work, we present initial results obtained in a series of recent space-based experiments and develop a detailed model describing the burning of ethanol droplet in microgravity.

Autoignition response of n-butanol and its blend with primary reference fuel constituents of gasoline.

DOE PAGES

Kumar, Kamal; Zhang, Yu; Sung, Chi -Jen; ...

2015-04-13

We study the influence of blending n-butanol on the ignition delay times of n-heptane and iso-octane, the primary reference fuels for gasoline. The ignition delay times are measured using a rapid compression machine, with an emphasis on the low-to-intermediate temperature conditions. The experiments are conducted at equivalence ratios of 0.4 and 1.0, for a compressed pressure of 20 bar, with the temperatures at the end of compression ranging from 613 K to 979 K. The effect of n-butanol addition on the development of the two-stage ignition characteristics for the two primary reference fuels is also examined. The experimental results aremore » compared to predictions obtained using a detailed chemical kinetic mechanism, which has been obtained by a systematic merger of previously reported base models for the combustion of the individual fuel constituents. In conclusion, a sensitivity analysis on the base, and the merged models, is also performed to understand the dependence of autoignition delay times on the model parameters.« less

Dihydro-β-agarofurans from the roots of the Australian endemic rainforest tree Maytenus bilocularis act as leucine transport inhibitors.

PubMed

Wibowo, Mario; Wang, Qian; Holst, Jeff; White, Jonathan M; Hofmann, Andreas; Davis, Rohan A

2018-04-01

Phytochemical studies of the roots of the Australian plant, Maytenus bilocularis, resulted in the identification of six previously undescribed dihydro-β-agarofuran sesquiterpenoids, bilocularins D-I, along with three known natural products, namely 1α,2α,6β,15-tetraacetoxy-9β-benzoyloxydihydro-β-agarofuran, pristimerin, and celastrol. The structures of all compounds were characterized via analysis of 1D/2D NMR and MS data. The absolute configuration of bilocularin D was defined by X-ray crystallography analysis. Bilocularins D and G, 1α,2α,6β,15-tetraacetoxy-9β-benzoyloxydihydro-β-agarofuran, and celastrol inhibited leucine transport in the human prostate cancer cell line LNCaP with IC 50 values ranging from 2.5-27.9 μM, which were more potent than the L-type amino acid transporter (LAT) family inhibitor 2-aminobicyclo[2,2,1]-heptane-2-carboxylic acid (BCH). Bilocularins D-F are the first examples of dihydro-β-agarofurans bearing a hydroxyacetate group. Copyright © 2018 Elsevier Ltd. All rights reserved.

Robust Polypropylene Fabrics Super-Repelling Various Liquids: A Simple, Rapid and Scalable Fabrication Method by Solvent Swelling.

PubMed

Zhu, Tang; Cai, Chao; Duan, Chunting; Zhai, Shuai; Liang, Songmiao; Jin, Yan; Zhao, Ning; Xu, Jian

2015-07-01

A simple, rapid (10 s) and scalable method to fabricate superhydrophobic polypropylene (PP) fabrics is developed by swelling the fabrics in cyclohexane/heptane mixture at 80 °C. The recrystallization of the swollen macromolecules on the fiber surface contributes to the formation of submicron protuberances, which increase the surface roughness dramatically and result in superhydrophobic behavior. The superhydrophobic PP fabrics possess excellent repellency to blood, urine, milk, coffee, and other common liquids, and show good durability and robustness, such as remarkable resistances to water penetration, abrasion, acidic/alkaline solution, and boiling water. The excellent comprehensive performance of the superhydrophobic PP fabrics indicates their potential applications as oil/water separation materials, protective garments, diaper pads, or other medical and health supplies. This simple, fast and low cost method operating at a relatively low temperature is superior to other reported techniques for fabricating superhydrophobic PP materials as far as large scale manufacturing is considered. Moreover, the proposed method is applicable for preparing superhydrophobic PP films and sheets as well.

[Properties of synthesized CdS nanoparticles by reverse micelle method].

PubMed

Li, Heng-Da; Wang, Qing-Wei; Zhai, Hong-Ju; Li, Wen-Lian

2008-07-01

Micelle system with reverse phase (water/CTAB/n-hexyl alcohol/n-heptane) is a weenie liquid-globelet of surface active agent molecule which can be stably and uniformly dispersed in continuous oil medium. The micelle system with reverse phase can work as a "micro-reactor" to synthesize CdS nano-particle with excellent performance. In the present article considering the effects of W value (W= [water]/[surface agent]) of the micelle system with reverse phase, we observed that the ratio of [Cd2+] and [S2-] ions to the original concentrations of the Cd2+ and S2- ions can affect the luminescent properties of CdS nano-particle. Using regurgitant treatment process the surface of CdS nano-particle can be modified, and as a result the defect emission was reduced and even disappeared, but exciton emissions markedly increased. On the other hand, a red-shift of the exciton emission peak with the increase in the particle size was observed, indicating considerable quantum confinement effect. A maximum quantum efficiency of 11% for the synthesized CdS nano-material was achieved.

Yields of Bacterial Cells from Hydrocarbons

PubMed Central

Wodzinski, Richard S.; Johnson, Marvin J.

1968-01-01

A strain of Nocardia and one of Pseudomonas, both isolated on pristane (2,6,10,14-tetramethylpentadecane), gave cell yields of approximately 100% on n-octadecane and pristane. Both organisms grew more rapidly on the n-octadecane than on the pristane. A mixed culture, isolated on 3-methylheptane, whose two components were identified as species of Pseudomonas and of Nocardia, gave approximately 100% cell yields and grew with generation times of about 5 hr on n-heptane, n-octane, and 2-methylheptane. The generation time on 3-methylheptane was 8.6 hr and the cell yield was only 79%. A strain of Pseudomonas isolated from naphthalene enrichments and one from phenanthrene enrichments both gave a cell yield of 50% on naphthalene. The phenanthrene isolate gave a cell yield of 40% on phenanthrene. A Nocardia species isolated on benzene gave a 79% cell yield on benzene. The generation times of the bacteria isolated on aromatic hydrocarbons were related to the solubility of the aromatic hydrocarbons on which they were grown; the more insoluble hydrocarbons gave slower growth. PMID:5726161

Simulation of low temperature combustion mechanism of different combustion-supporting agents in close-coupled DOC and DPF system.

PubMed

Jiao, Penghao; Li, Zhijun; Li, Qiang; Zhang, Wen; He, Li; Wu, Yue

2018-07-01

In the coupled Diesel Oxidation Catalyst (DOC) and Diesel Particular Filter (DPF) system, soot cannot be completely removed by only using the passive regeneration. And DPF active regeneration is necessary. The research method in this paper is to spray different kinds of combustion-supporting agents to the DOC in the front of the DPF. Therefore, the low temperature combustion mechanism of different kinds of combustion-supporting agents in DOC was studied, in order to grasp the law of combustion in DOC, and the influence of follow-up emission on DPF removal of soot. During the study, CH 4 H 2 mixture and diesel (n-heptane + toluene) were used as combustion-supporting agents respectively. The simplified mechanisms of two kinds of gas mixtures used as the combustion-supporting agents in DPF have been constructed and testified in the paper. In this paper, the combustion and emission conditions of the two combustion-supporting agents were analyzed so as to meet the practical requirements of different working conditions. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Simplex optimization of headspace factors for headspace gas chromatography determination of residual solvents in pharmaceutical products.

PubMed

Grodowska, Katarzyna; Parczewski, Andrzej

2013-01-01

The purpose of the present work was to find optimum conditions of headspace gas chromatography (HS-GC) determination of residual solvents which usually appear in pharmaceutical products. Two groups of solvents were taken into account in the present examination. Group I consisted of isopropanol, n-propanol, isobutanol, n-butanol and 1,4-dioxane and group II included cyclohexane, n-hexane and n-heptane. The members of the groups were selected in previous investigations in which experimental design and chemometric methods were applied. Four factors were taken into consideration in optimization which describe HS conditions: sample volume, equilibration time, equilibrium temperature and NaCl concentration in a sample. The relative GC peak area served as an optimization criterion which was considered separately for each analyte. Sequential variable size simplex optimization strategy was used and the progress of optimization was traced and visualized in various ways simultaneously. The optimum HS conditions appeared different for the groups of solvents tested, which proves that influence of experimental conditions (factors) depends on analyte properties. The optimization resulted in significant signal increase (from seven to fifteen times).

Combustion of Biofuel as a Renewable Energy Source in Sandia Flame Geometry

NASA Astrophysics Data System (ADS)

Rassoulinejad-Mousavi, Seyed Moein; Mao, Yijin; Zhang, Yuwen

Energy security and climate change are two important key causes of wide spread employment of biofuel notwithstanding of problems associated with its usage. In this research, combustion of biofuel as a renewable energy source was numerically investigated in the well-known and practical Sandia flame geometry. Combustion performance of the flame has been simulated by burning biodiesel (methyl decanoate, methyl 9-decenoate, and n-heptane) oxidation with 118 species reduced/skeletal mechanism. The open-source code OpenFoam was used for simulating turbulent biodiesel-air combustion in the cylindrical chamber using the standard k-epsilon model. To check the accuracy of numerical results, the system was initially validated with methane-air Sandia national laboratories flame D experimental results. Excellent agreements between numerical and experimental results were observed at different cross sections. After ignition, temperature distributions at different distances of axial and radial directions as well as species mass fraction were investigated. It is concluded that biofuel has the capability of implementation in the turbulent jet flame that is a step forward in promotion of sustainable energy technologies and applications.

The creation of modulated monoclinic aperiodic composites in n-alkane/urea compounds

DOE PAGES

Mariette, Céline; Guérin, Laurent; Rabiller, Philippe; ...

2014-09-12

n-Dodecane/urea is a member of the prototype series of n-alkane/urea inclusion compounds. At room temperature, it presents a quasi-one dimensional liquid-like state for the confined guest molecules within the rigid, hexagonal framework of the urea host. At lower temperatures, we report the existence of two other phases. Below T c=248 K there appears a phase with rank four superspace group P6 122(00γ), the one typically observed at room temperature in n-alkane/urea compounds with longer guest molecules. A misfit parameter, defined by the ratio γ=c h/c g (c host/c guest), is found to be 0.632±0.005. Below T c1=123 K, a monoclinicmore » modulated phase is created with a constant shift along c of the guest molecules in adjacent channels. The maximal monoclinic space group for this structure is P12 11(α0γ). We discuss analogies and differences with n-heptane/urea, which also presents a monoclinic, modulated low-temperature phase.« less

Determination of trace elements in automotive fuels by filter furnace atomic absorption spectrometry

NASA Astrophysics Data System (ADS)

Anselmi, Anna; Tittarelli, Paolo; Katskov, Dmitri A.

2002-03-01

The determination of Cd, Cr, Cu, Pb and Ni was performed in gasoline and diesel fuel samples by electrothermal atomic absorption spectrometry using the Transverse Heated Filter Atomizer (THFA). Thermal conditions were experimentally defined for the investigated elements. The elements were analyzed without addition of chemical modifiers, using organometallic standards for the calibration. Forty-microliter samples were injected into the THFA. Gasoline samples were analyzed directly, while diesel fuel samples were diluted 1:4 with n-heptane. The following characteristic masses were obtained: 0.8 pg Cd, 6.4 pg Cr, 12 pg Cu, 17 pg Pb and 27 pg Ni. The limits of determination for gasoline samples were 0.13 μg/kg Cd, 0.4 μg/kg Cr, 0.9 μg/kg Cu, 1.5 μg/kg Pb and 2.5 μg/kg Ni. The corresponding limit of determination for diesel fuel samples was approximately four times higher for all elements. The element recovery was performed using the addition of organometallic compounds to gasoline and diesel fuel samples and was between 85 and 105% for all elements investigated.

In Vitro Dermo-Cosmetic Evaluation of Bark Extracts from Common Temperate Trees.

PubMed

Hubert, Jane; Angelis, Apostolis; Aligiannis, Nektarios; Rosalia, Michalea; Abedini, Amin; Bakiri, Ali; Reynaud, Romain; Nuzillard, Jean-Marc; Gangloff, Sophie C; Skaltsounis, Alexios-Leandros; Renault, Jean-Hugues

2016-10-01

Wood residues produced from forestry activities represent an interesting source of biologically active, high value-added secondary metabolites. In this study, 30 extracts from 10 barks of deciduous and coniferous tree species were investigated for their potential dermo-cosmetic use. The extracts were obtained from Fagus sylvatica, Quercus robur, Alnus glutinosa, Prunus avium, Acer pseudoplatanus, Fraxinus excelsior, Populus robusta, Larix decidua, Picea abies , and Populus tremula after three successive solid/liquid extractions of the barks with n- heptane, methanol, and methanol/water. All extracts were evaluated for their radical scavenging capacity, for their elastase, collagenase, and tyrosinase inhibitory activities, as well as for their antibacterial activity against gram-positive Staphylococcus aureus . In parallel, the global metabolite profiles of all extracts were established by 1D and 2D NMR and related to their biological activity. The results showed that the methanol extracts of Q. robur, A. glutinosa, L. decidua , and P. abies barks exhibit particularly high activities on most bioassays, suggesting their promising use as active ingredients in the dermo-cosmetic industry. Georg Thieme Verlag KG Stuttgart · New York.

Optimizing carbon efficiency of jet fuel range alkanes from cellulose co-fed with polyethylene via catalytically combined processes.

PubMed

Zhang, Xuesong; Lei, Hanwu; Zhu, Lei; Zhu, Xiaolu; Qian, Moriko; Yadavalli, Gayatri; Yan, Di; Wu, Joan; Chen, Shulin

2016-08-01

Enhanced carbon yields of renewable alkanes for jet fuels were obtained through the catalytic microwave-induced co-pyrolysis and hydrogenation process. The well-promoted ZSM-5 catalyst had high selectivity toward C8-C16 aromatic hydrocarbons. The raw organics with improved carbon yield (∼44%) were more principally lumped in the jet fuel range at the catalytic temperature of 375°C with the LDPE to cellulose (representing waste plastics to lignocellulose) mass ratio of 0.75. It was also observed that the four species of raw organics from the catalytic microwave co-pyrolysis were almost completely converted into saturated hydrocarbons; the hydrogenation process was conducted in the n-heptane medium by using home-made Raney Ni catalyst under a low-severity condition. The overall carbon yield (with regards to co-reactants of cellulose and LDPE) of hydrogenated organics that mostly match jet fuels was sustainably enhanced to above 39%. Meanwhile, ∼90% selectivity toward jet fuel range alkanes was attained. Copyright © 2016 Elsevier Ltd. All rights reserved.

Long Duration Exposure Facility (LDEF) low-temperature Heat Pipe Experiment Package (HEPP) flight results

NASA Technical Reports Server (NTRS)

Mcintosh, Roy; Mccreight, Craig; Brennan, Patrick J.

1992-01-01

The Low Temperature Heat Pipe Flight Experiment (HEPP) is a fairly complicated thermal control experiment that was designed to evaluate the performance of two different low temperature ethane heat pipes and a n-Heptane Phase Change Material (PCM) canister. A total of 388 days of continuous operation with an axially grooved aluminum fixed conductance heat pipe of axially grooved stainless steel heat pipe diode was demonstrated before the EDS batteries lost power. The inability of the HEPP's radiator to cool below 190 K in flight prevented freezing of the PCM and the opportunity to conduct transport tests with the heat pipes. Post flight tests showed that the heat pipes and the PCM are still functioning. This paper presents a summary of the flight data analysis for the HEPP and its related support systems. Pre and post-flight thermal vacuum tests results are presented for the HEPP thermal control system along with individual heat pipe performance and PCM behavior. Appropriate SIG related systems data will also be included along with a 'lessons learned' summary.

Role of low density lipoprotein in the activation of plasma lysolecithin acyltransferase activity. Effect of chemical and enzymatic modifications of the lipoprotein on enzyme activity.

PubMed

Subbaiah, P V; Chen, C H; Bagdade, J D; Albers, J J

1985-01-01

The effect of various chemical and enzymatic modifications of low density lipoprotein (LDL) on its ability to activate the isolated human plasma lysolecithin acyltransferase (LAT) was studied. Removal of all lipids from LDL resulted in the complete loss of LAT activation. Removal of only neutral lipids by extraction with heptane retained up to 50% of the original activity, which was not increased further by reconstitution of the LDL with the extracted lipids. Hydrolysis of the diacylphosphoglycerides of the LDL with phospholipases resulted in complete loss of LAT activation which was partially restored by the addition of egg lecithin. Hydrolysis of more than 4% of LDL protein by trypsin led to a linear decrease in activity with complete loss of activity occurring when about 25% of the LDL protein is hydrolyzed. Modification of the arginine groups of LDL reversibly inhibited the activation of LAT. Modification of lysine residues of LDL by acetylation, acetoacetylation or succinylation also abolished its ability to activate lysolecithin acylation.

Stacking faults and mechanisms strain-induced transformations of hcp metals (Ti, Mg) during mechanical activation in liquid hydrocarbons

NASA Astrophysics Data System (ADS)

Lubnin, A. N.; Dorofeev, G. A.; Nikonova, R. M.; Mukhgalin, V. V.; Lad'yanov, V. I.

2017-11-01

The evolution of the structure and substructure of metals Ti and Mg with hexagonal close-packed (hcp) lattice is studied during their mechanical activation in a planetary ball mill in liquid hydrocarbons (toluene, n-heptane) and with additions of carbon materials (graphite, fullerite, nanotubes) by X-ray diffraction, scanning electron microscopy, and chemical analysis. The temperature behavior and hydrogen-accumulating properties of mechanocomposites are studied. During mechanical activation of Ti and Mg, liquid hydrocarbons decay, metastable nanocrystalline titanium carbohydride Ti(C,H) x and magnesium hydride β-MgH2 are formed, respectively. The Ti(C,H) x and MgH2 formation mechanisms during mechanical activation are deformation ones and are associated with stacking faults accumulation, and the formation of face-centered cubic (fcc) packing of atoms. Metastable Ti(C,H)x decays at a temperature of 550°C, the partial reverse transformation fcc → hcp occurs. The crystalline defect accumulation (nanograin boundaries, stacking faults), hydrocarbon destruction, and mechanocomposite formation leads to the enhancement of subsequent magnesium hydrogenation in the Sieverts reactor.

Synthesis of 9,9,9-trideutero-1,4-dihydroxynonane mercapturic acid (d3-DHN-MA), a useful internal standard for DHN-MA urinalysis.

PubMed

Chantegrel, B; Deshayes, C; Doutheau, A; Steghens, J P

2002-10-01

Racemic 1,4-dihydroxynonane mercapturic acid (DHN-MA) and 9,9,9-trideutero-1,4-dihydroxynonane mercapturic acid (d3-DHN-MA) are synthesized on a 400-mg scale (overall yield approximately 40%) by a two-step sequence involving Michael addition of N-acetyl-L-cysteine to methyl 4-hydroxynon-2(E)-enoate or methyl 9,9,9-trideutero-4-hydroxynon-2 (E)-enoate, followed by reduction of the intermediate adducts with lithium borohydride. The requisite starting methyl esters are obtained, respectively, from heptanal or 7,7,7-trideuteroheptanal and methyl 4-chlorophenylsulfinylacetate via a sulfoxide piperidine and carbonyl reaction described in the literature. The 7,7,7-trideuteroheptanal is easily prepared by classical methods in four steps from 6-bromo-1-hexanol. 13C NMR data indicate that DHN-MA as well as d3-DHN-MA are obtained as mixtures of four diastereomers. Preliminary results show that d3-DHN-MA could be used as an internal standard for mass spectrometric quantification of DHN-MA in human urine.

High pressure droplet burning experiments in reduced gravity

NASA Technical Reports Server (NTRS)

Chauveau, Christian; Goekalp, Iskender

1995-01-01

A parametric investigation of single droplet gasification regimes is helpful in providing the necessary physical ideas for sub-grid models used in spray combustion numerical prediction codes. A research program has been initiated at the LCSR to explore the vaporization regimes of single and interacting hydrocarbon and liquid oxygen droplets under high pressure conditions. This paper summarizes the status of the LCSR program on the high pressure burning of single fuel droplets; recent results obtained under normal and reduced gravity conditions with suspended droplets are presented. In the work described here, parabolic flights of the CNES Caravelle is used to create a reduced gravity environment of the order of 10(exp -2) g(sub O). For all the droplet burning experiments reported here, the suspended droplet initial diameters are scattered around 1.5 mm; and the ambient air temperature is 300 K. The ambient pressure is varied between 0.1 MPa and 12 MPa. Four fuels are investigated: methanol (Pc = 7.9 MPa), n-heptane (Pc = 2.74 MPa), n-hexane (Pc = 3.01 MPa) and n-octane (Pc = 2.48 MPa).

Interfacial force field characterization of a constrained vapor bubble thermosyphon using IAI

NASA Technical Reports Server (NTRS)

Dasgupta, Sunando; Plawsky, Joel L.; Wayner, Peter C., Jr.

1994-01-01

The isothermal profiles of the extended meniscus in a quartz cuvette were measured in a gravitational field using IAI (image analyzing interferometer) which is based on computer enhanced video microscopy of the naturally occurring interference fringes. The experimental results for heptane and pentane menisci were analyzed using the extended Young-Laplace Equation. These isothermal results characterized the interfacial force field in-situ at the start of the heat transfer experiments by quantifying the dispersion constant for the specific liquid-solid system. The experimentally obtained values of the disjoining pressures and the dispersion constants are compared to the subsequent non-isothermal experiments because one of the major variables in the heat sink capability of the CVBT is the dispersion constant. In all previous studies of micro heat pipes the value of the dispersion constant has been 'guesstimated'. The major advantages of the current glass cell is the ability to view the extended meniscus at all times. Experimentally, we find that the extended Young-Laplace Equation is an excellent model for for the force field at the solid-liquid vapor interfaces.

Olfactory and quantitative analysis of aroma compounds in elder flower (Sambucus nigra L.) drink processed from five cultivars.

PubMed

Jørgensen, U; Hansen, M; Christensen, L P; Jensen, K; Kaack, K

2000-06-01

Fresh elder flowers (Sambucus nigra L.) were extracted with an aqueous solution containing sucrose, peeled lemon slices, tartaric acid, and sodium benzoate to make elder flower syrup. Aroma compounds emitted from the elder flower syrup were collected by the dynamic headspace technique and analyzed by GC-FID and GC-MS. A total of 59 compounds were identified, 18 of which have not previously been detected in elder flower products. The concentrations of the identified volatiles were measured in five elder cultivars, Allesoe, Donau, Sambu, Sampo, and Samyl, and significant differences were detected among cultivars in the concentration levels of 48 compounds. The odor of the volatiles was evaluated by the GC-sniffing technique. cis-Rose oxide, nerol oxide, hotrienol, and nonanal contributed to the characteristic elder flower odor, whereas linalool, alpha-terpineol, 4-methyl-3-penten-2-one, and (Z)-beta-ocimene contributed with floral notes. Fruity odors were associated with pentanal, heptanal, and beta-damascenone. Fresh and grassy odors were primarily correlated with hexanal, hexanol, and (Z)-3-hexenol.

Simple and double emulsions via electrospray

NASA Astrophysics Data System (ADS)

Barrero, Antonio; Loscertales, Ignacio G.

2005-11-01

Generation of nanoemulsions is of great interest in medical and pharmaceutical applications; drug delivery or antiviral emulsions are typical examples. The use of electrosprays for dispersing liquids inside liquid insulator baths have been recently reported, (Barrero et al. J. Colloid Interf. Sci. 272, 104, 2004). Capsules, nanotubes and coaxial nanofibers have been obtained from electrified coaxial jets (Loscertales et al. Science 295, n. 5560, 1695, 2002; J. American Chem. Soc. 126, 5376, 2004). Here we present a method for making double emulsions (both water-oil-water and o/w/o) based on the generation of compound electrosprays inside insulator liquid baths. Basically, a conducting liquid injected throughout a capillary needle is electroatomized in cone-jet mode inside a dielectric liquid bath. A third insulating liquid is injected inside the Taylor cone to form a second meniscus. Then, a steady coaxial jet, in which the insulating liquid is coated by the conducting one, develops. A double emulsion forms as a result of the jet breaking up into compound droplets electrically charged. Experimental results carried out with glycerine and different oils in a bath of heptane are reported.

IDENTITY OF THE PINK-PIGMENTED METHANOL-OXIDIZING BACTERIA AS VIBRIO EXTORQUENS

PubMed Central

Stocks, Peter K.; McCleskey, C. S.

1964-01-01

Stocks, Peter K. (Louisiana State University, Baton Rouge), and C. S. McCleskey. Identity of the pink-pigmented methanol-oxidizing bacteria as Vibrio extorquens. J. Bacteriol. 88:1065–1070. 1964.—Pink-pigmented bacteria isolated from enrichment cultures of methane oxidizers were found to possess similar morphological, cultural, and physiological characteristics. All the strains utilized methanol, formate, oxalate, succinate, glycerol, and benzene as sole carbon sources; methanol, formate, and glycerol afforded best growth. Most strains utilized fructose and ribose; other carbohydrates tested were not available as carbon and energy sources. There was strain variation in the use of hexane, heptane, n-propanol, n-butanol, acetate, and propionate. Methane, ethane, n-propane, and n-butane were not utilized. Our isolates, and Pseudomonas methanica of Harrington and Kallio (not the methane-dependent P. methanica of Dworkin and Foster), Pseudomonas AM1 of Peele and Quayle, Pseudomonas PRL-W4 of Kaneda and Roxburgh, and Protaminobacter ruber den Dooren de Jong are nearly identical with Vibrio extorquens (Bassalik) Bhat and Barker, and should be considered the same species. Images PMID:14219020

IDENTITY OF THE PINK-PIGMENTED METHANOL-OXIDIZING BACTERIA AS VIBRIO EXTORQUENS.

PubMed

STOCKS, P K; MCCLESKEY, C S

1964-10-01

Stocks, Peter K. (Louisiana State University, Baton Rouge), and C. S. McCleskey. Identity of the pink-pigmented methanol-oxidizing bacteria as Vibrio extorquens. J. Bacteriol. 88:1065-1070. 1964.-Pink-pigmented bacteria isolated from enrichment cultures of methane oxidizers were found to possess similar morphological, cultural, and physiological characteristics. All the strains utilized methanol, formate, oxalate, succinate, glycerol, and benzene as sole carbon sources; methanol, formate, and glycerol afforded best growth. Most strains utilized fructose and ribose; other carbohydrates tested were not available as carbon and energy sources. There was strain variation in the use of hexane, heptane, n-propanol, n-butanol, acetate, and propionate. Methane, ethane, n-propane, and n-butane were not utilized. Our isolates, and Pseudomonas methanica of Harrington and Kallio (not the methane-dependent P. methanica of Dworkin and Foster), Pseudomonas AM1 of Peele and Quayle, Pseudomonas PRL-W4 of Kaneda and Roxburgh, and Protaminobacter ruber den Dooren de Jong are nearly identical with Vibrio extorquens (Bassalik) Bhat and Barker, and should be considered the same species.

A diketiminate-bound diiron complex with a bridging carbonate ligand

PubMed Central

Sadique, Azwana R.; Brennessel, William W.; Holland, Patrick L.

2009-01-01

Reduction of carbon dioxide by a diiron(I) complex gives μ-carbonato-κ3 O:O′,O′′-bis­{[2,2,6,6-tetra­methyl-3,5-bis­(2,4,6-triisopropyl­phenyl)heptane-2,5-diiminate(1−)-κ2 N,N′]iron(II)} toluene disolvate, [Fe2(C41H65N)2(CO3)]·2C7H8, a diiron(II) species with a bridging carbonate ligand. The asymmetric unit contains one diiron complex and two cocrystallized toluene solvent mol­ecules that are distributed over three sites, one with atoms in general positions and two in crystallographic sites. Both FeII atoms are η2-coordinated to diketiminate ligands, but η1- and η2-coordinated to the bridging carbonate ligand. Thus, one FeII center is three-coordinate and the other is four-coordinate. The bridging carbonate ligand is nearly perpendicular to the iron–diketiminate plane of the four-coordinate FeII center and parallel to the plane of the three-coordinate FeII center. PMID:19407402

Experimental Study of Unsupported Nonane fuel Droplet Combustion in Microgravity

NASA Technical Reports Server (NTRS)

Callahan, B. J.; Avedisian, C. T.; Hertzog, D. E.; Berkery, J. W.

1999-01-01

Soot formation in droplet flames is the basic component of the particulate emission process that occurs in spray combustion. The complexity of soot formation motivates a one-dimensional transport condition which has obvious advantages in modeling. Recent models of spherically symmetric droplet combustion have made this assumption when incorporating such aspects as detailed chemistry and radiation. Interestingly, spherical symmetry does not necessarily restrict the results because it has been observed that the properties of carbon formed in flames are not strongly affected by the nature of the fuel or flaming configuration. What is affected, however, are the forces acting on the soot aggregates and where they are trapped by a balance of drag and thermophoretic forces. The distribution of these forces depends on the transport conditions of the flame. Prior studies of spherical droplet flames have examined the droplet burning history of alkanes, alcohols and aromatics. Data are typically the evolution of droplet, flame, extinction, and soot shell diameters. These data are only now just beginning to find their way into comprehensive numerical models of droplet combustion to test proposed oxidation schemes for fuels such as methanol and heptane. In the present study, we report new measurements on the burning history of unsupported nonane droplets in a convection-free environment to promote spherical symmetry. The far-field gas is atmospheric pressure air at room temperature. The evolution of droplet diameter was measured using high speed cine photography of a spark-ignited, droplet within a confined volume in a drop tower. The initial droplet diameters varied between 0.5 mm and 0.6 mm. The challenge of unsupported droplets is to form, deploy and ignite them with minimal disturbance, and then to keep them in the camera field of view. Because of the difficulty of this undertaking, more sophisticated diagnostics for studying soot than photographic were not used. Supporting the test droplet by a fiber fixes the droplet position but the fiber can perturb the burning process especially for a sooting fuel. Prior studies on heptane showed little evidence for soot formation due to g-droplets of similar size the relationship between sooting and droplet diameter. For nonane droplets we expect increased sooting due to the greater number of carbon atoms. As a sooting droplet burns and its diameter decreases, proportionally less soot should form. This reduced soot, as well as the influence of soot formed earlier in the burning process which collects in a 'shell', on heat transport to the flame offers the potential for a time-varying burning rate. Such an effect was investigated and revealed in results reported here. Speculation is offered for the cause of this effect and its possible relation to soot formation.

Modeling of Alkane Oxidation Using Constituents and Species

NASA Technical Reports Server (NTRS)

Bellan, Jasette; Harstad, Kenneth G.

2010-01-01

It is currently not possible to perform simulations of turbulent reactive flows due in particular to complex chemistry, which may contain thousands of reactions and hundreds of species. This complex chemistry results in additional differential equations, making the numerical solution of the equation set computationally prohibitive. Reducing the chemical kinetics mathematical description is one of several important goals in turbulent reactive flow modeling. A chemical kinetics reduction model is proposed for alkane oxidation in air that is based on a parallel methodology to that used in turbulence modeling in the context of the Large Eddy Simulation. The objective of kinetic modeling is to predict the heat release and temperature evolution. This kinetic mechanism is valid over a pressure range from atmospheric to 60 bar, temperatures from 600 K to 2,500 K, and equivalence ratios from 0.125 to 8. This range encompasses diesel, HCCI, and gas-turbine engines, including cold ignition. A computationally efficient kinetic reduction has been proposed for alkanes that has been illustrated for n-heptane using the LLNL heptane mechanism. This model is consistent with turbulence modeling in that scales were first categorized into either those modeled or those computed as progress variables. Species were identified as being either light or heavy. The heavy species were decomposed into defined 13 constituents, and their total molar density was shown to evolve in a quasi-steady manner. The light species behave either in a quasi-steady or unsteady manner. The modeled scales are the total constituent molar density, Nc, and the molar density of the quasi-steady light species. The progress variables are the total constituent molar density rate evolution and the molar densities of the unsteady light species. The unsteady equations for the light species contain contributions of the type gain/loss rates from the heavy species that are modeled consistent with the developed mathematical forms for the total constituent molar density rate evolution; indeed, examination of these gain/loss rates shows that they also have a good quasi-steady behavior with a functional form resembling that of the constituent rate. This finding highlights the fact that the fitting technique provides a methodology that can be repeatedly used to obtain an accurate representation of full or skeletal kinetic models. Assuming success with the modified reduced model, the advantage of the modeling approach is clear. Because this model is based on the Nc rate rather than on that of individual heavy species, even if the number of species increases with increased carbon number in the alkane group, providing that the quasi-steady rate aspect persists, then extension of this model to higher alkanes should be conceptually straightforward, although it remains to be seen if the functional fits would remain valid or would require reconstruction.

Lipopolysaccharide Structure and Biosynthesis in Helicobacter pylori.

PubMed

Li, Hong; Liao, Tingting; Debowski, Aleksandra W; Tang, Hong; Nilsson, Hans-Olof; Stubbs, Keith A; Marshall, Barry J; Benghezal, Mohammed

2016-12-01

This review covers the current knowledge and gaps in Helicobacter pylori lipopolysaccharide (LPS) structure and biosynthesis. H. pylori is a Gram-negative bacterium which colonizes the luminal surface of the human gastric epithelium. Both a constitutive alteration of the lipid A preventing TLR4 elicitation and host mimicry of the Lewis antigen decorated O-antigen of H. pylori LPS promote immune escape and chronic infection. To date, the complete structure of H. pylori LPS is not available, and the proposed model is a linear arrangement composed of the inner core defined as the hexa-saccharide (Kdo-LD-Hep-LD-Hep-DD-Hep-Gal-Glc), the outer core composed of a conserved trisaccharide (-GlcNAc-Fuc-DD-Hep-) linked to the third heptose of the inner core, the glucan, the heptan and a variable O-antigen, generally consisting of a poly-LacNAc decorated with Lewis antigens. Although the glycosyltransferases (GTs) responsible for the biosynthesis of the H. pylori O-antigen chains have been identified and characterized, there are many gaps in regard to the biosynthesis of the core LPS. These limitations warrant additional mutagenesis and structural studies to obtain the complete LPS structure and corresponding biosynthetic pathway of this important gastric bacterium. © 2016 John Wiley & Sons Ltd.

Application of edible paraffin oil for cationic dye removal from water using emulsion liquid membrane.

PubMed

Zereshki, Sina; Daraei, Parisa; Shokri, Amin

2018-05-18

Using an emulsion liquid membrane based on edible oils is investigated for removing cationic dyes from aqueous solutions. There is a great potential for using edible oils in food industry extraction processes. The parameters affecting the stability of the emulsion and the extraction rate were studied. These parameters were the emulsification time, the stirring speed, the surfactant concentration, the internal phase concentration, the feed phase concentration, the volume ratio of internal phase to organic phase and the treat ratio. In order to stabilize the emulsion without using a carrier, edible paraffin oil and heptane are used at an 80:20 ratio. The optimum conditions for the extraction of methylene blue (MB), crystal violet and methyl violet (CV and MV) cationic dyes using edible paraffin oil as an environment friendly solvent are represented. A removal percentage of 95% was achieved for a mixture of dyes. The optimum concentration of sodium hydroxide in the internal phase, which results a stabile emulsion with a high stripping efficiency of 96%, was 0.04 M. An excellent membrane recovery was observed and the extraction of dyes did not decrease up to seven run cycles. Copyright © 2018 Elsevier B.V. All rights reserved.

Study of the rice straw biodegradation in mixed culture of Trichoderma viride and Aspergillus niger by GC-MS and FTIR.

PubMed

Chen, Yaoning; Huang, Jingxia; Li, Yuanping; Zeng, Guangming; Zhang, Jiachao; Huang, Aizhi; Zhang, Jie; Ma, Shuang; Tan, Xuebin; Xu, Wei; Zhou, Wei

2015-07-01

This study was conducted to investigate the biodegradation ability of the mixed culture of Trichoderma viride and Aspergillus niger through the study of the organic matter extracted from rice straw and the lignocellulose structure by using gas chromatography-mass spectrometer (GC-MS) and Fourier transform infrared spectroscopy (FTIR). The results of the GC-MS showed that the mixed culture possessed shorter alkane (heptane) at the end of the incubation and more kinds of organic matter (except the alkanes, 29 kinds of organic matter were detected) than the pure cultures. It could be deduced that the organic matter could indicate the degradation degree of the lignocellulose to some extent. Moreover, pinene was detected in the mixed culture on days 5 and 10, which might represent the antagonistic relationship between T. viride and A. niger. The analysis of FTIR spectrums which indirectly verified the GC-MS results showed that the mixed culture possessed a better degradation of rice straw compared with the pure culture. Therefore, the methods used in this research could be considered as effective ones to investigate the lignocellulose degradation mechanism in mixed culture.

Endogenous Intoxication and Saliva Lipid Peroxidation in Patients with Lung Cancer.

PubMed

Bel'skaya, Lyudmila V; Kosenok, Victor K; Massard, Gilbert

2016-11-16

This research was aimed at a search for regularities in changes to parameters of endogenous intoxication and saliva lipid peroxidation in patients with lung cancer, non-malignant lung diseases, and apparently healthy people. All patients went through saliva sampling at an amount of 1 mL. A concentration of malondialdehyde (MDA) was measured according to a reaction with thiobarbituric acid, and a level of middle molecules (MM) was measured with UV spectroscopy at 254 and 280 nm, while the content of lipid peroxidation products was measured according to a degree of heptane extract light absorption at wavelengths of 220, 232, 278, and 400 nm. It has been revealed that in the context of lung cancer, the level of diene conjugates decreases, increasing the level of triene conjugates, Schiff's bases, and MM. As a tumor grows, there is a decrease in the level of lipid peroxidation primary products and an increase in endotoxemia phenomena. The process is more apparent when going from local to locally advanced disease states. The nature of the MDA change is nonlinearly associated with tumor progression. The findings might be used to optimize traditional aids of diagnostics, in disease state forecasting, in treatment monitoring, etc.

Molecular-dynamics simulation of mutual diffusion in nonideal liquid mixtures

NASA Astrophysics Data System (ADS)

Rowley, R. L.; Stoker, J. M.; Giles, N. F.

1991-05-01

The mutual-diffusion coefficients, D 12, of n-hexane, n-heptane, and n-octane in chloroform were modeled using equilibrium molecular-dynamics (MD) simulations of simple Lennard-Jones (LJ) fluids. Pure-component LJ parameters were obtained by comparison of simulations to experimental self-diffusion coefficients. While values of “effective” LJ parameters are not expected to simulate accurately diverse thermophysical properties over a wide range of conditions, it was recently shown that effective parameters obtained from pure self-diffusion coefficients can accurately model mutual diffusion in ideal, liquid mixtures. In this work, similar simulations are used to model diffusion in nonideal mixtures. The same combining rules used in the previous study for the cross-interaction parameters were found to be adequate to represent the composition dependence of D 12. The effect of alkane chain length on D 12 is also correctly predicted by the simulations. A commonly used assumption in empirical correlations of D 12, that its kinetic portion is a simple, compositional average of the intradiffusion coefficients, is inconsistent with the simulation results. In fact, the value of the kinetic portion of D 12 was often outside the range of values bracketed by the two intradiffusion coefficients for the nonideal system modeled here.

Science Support for Space-Based Droplet Combustion: Drop Tower Experiments and Detailed Numerical Modeling

NASA Technical Reports Server (NTRS)

Marchese, Anthony J.; Dryer, Frederick L.

1997-01-01

This program supports the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies. Experimental emphasis is on the study of simple alcohols (methanol, ethanol) and alkanes (n-heptane, n-decane) as fuels with time dependent measurements of drop size, flame-stand-off, liquid-phase composition, and finally, extinction. Experiments have included bench-scale studies at Princeton, studies in the 2.2 and 5.18 drop towers at NASA-LeRC, and both the Fiber Supported Droplet Combustion (FSDC-1, FSDC-2) and the free Droplet Combustion Experiment (DCE) studies aboard the shuttle. Test matrix and data interpretation are performed through spherically-symmetric, time-dependent numerical computations which embody detailed sub-models for physical and chemical processes. The computed burning rate, flame stand-off, and extinction diameter are compared with the respective measurements for each individual experiment. In particular, the data from FSDC-1 and subsequent space-based experiments provide the opportunity to compare all three types of data simultaneously with the computed parameters. Recent numerical efforts are extending the computational tools to consider time dependent, axisymmetric 2-dimensional reactive flow situations.

Anaplerotic input is sufficient to induce time-dependent potentiation of insulin release in rat pancreatic islets.

PubMed

Gunawardana, Subhadra C; Liu, Yi-Jia; Macdonald, Michael J; Straub, Susanne G; Sharp, Geoffrey W G

2004-11-01

Nutrients that induce biphasic insulin release, such as glucose and leucine, provide acetyl-CoA and anaplerotic input in the beta-cell. The first phase of release requires increased ATP production leading to increased intracellular Ca(2+) concentration ([Ca(2+)](i)). The second phase requires increased [Ca(2+)](i) and anaplerosis. There is strong evidence to indicate that the second phase is due to augmentation of Ca(2+)-stimulated release via the K(ATP) channel-independent pathway. To test whether the phenomenon of time-dependent potentiation (TDP) has similar properties to the ATP-sensitive K(+) channel-independent pathway, we monitored the ability of different agents that provide acetyl-CoA and anaplerotic input or both of these inputs to induce TDP. The results show that anaplerotic input is sufficient to induce TDP. Interestingly, among the agents tested, the nonsecretagogue glutamine, the nonhydrolyzable analog of leucine aminobicyclo[2.2.1]heptane-2-carboxylic acid, and succinic acid methyl ester all induced TDP, and all significantly increased alpha-ketoglutarate levels in the islets. In conclusion, anaplerosis that enhances the supply and utilization of alpha-ketoglutarate in the tricarboxylic acid cycle appears to play an essential role in the generation of TDP.

Determination of Carbonyl Compounds in Cork Agglomerates by GDME-HPLC-UV: Identification of the Extracted Compounds by HPLC-MS/MS.

PubMed

Brandão, Pedro Francisco; Ramos, Rui Miguel; Almeida, Paulo Joaquim; Rodrigues, José António

2017-02-08

A new approach is proposed for the extraction and determination of carbonyl compounds in solid samples, such as wood or cork materials. Cork products are used as building materials due to their singular characteristics; however, little is known about its aldehyde emission potential and content. Sample preparation was done by using a gas-diffusion microextraction (GDME) device for the direct extraction of volatile aldehydes and derivatization with 2,4-dinitrophenylhydrazine. Analytical determination of the extracts was done by HPLC-UV, with detection at 360 nm. The developed methodology proved to be a reliable tool for aldehyde determination in cork agglomerate samples with suitable method features. Mass spectrometry studies were performed for each sample, which enabled the identification, in the extracts, of the derivatization products of a total of 13 aldehydes (formaldehyde, acetaldehyde, furfural, propanal, 5-methylfurfural, butanal, benzaldehyde, pentanal, hexanal, trans-2-heptenal, heptanal, octanal, and trans-2-nonenal) and 4 ketones (3-hydroxy-2-butanone, acetone, cyclohexanone, and acetophenone). This new analytical methodology simultaneously proved to be consistent for the identification and determination of aldehydes in cork agglomerates and a very simple and straightforward procedure.

Simultaneous ultramicroanalysis of both 17-keto-and 17beta-hydroxy androgens in biological fluids.

PubMed

Ganjam, V K

1976-11-01

Sensitive methods for quantifying androgens were lacking. Therefore, a relatively simple procedure for separating steroids was combined with highly specific assay methods so that eight androgens could be measured with high accuracy, precision and sensitivity. Semi-automated separations on Sephadex LH-20 columns used heptane:methylene chloride:ethanol:water (50:50:1:0.12) and a flow rate of 17.0 min/ml. The six peaks eluted contained androstenedine; androsterone, epiandrosterone and dihydrotestosterone; testosterone and dehydroepiandrosterone; 3alpha-androstanediol; 3beta-androstanediol; and androstenediol. Androstenedione, dehydroepiandrosterone and androstenediol were quantified using specific antisera (sensitivity less than or equal to 75 pg). Testosterone and dihydrotestosterone were measured by competitive protein-binding assays using rabbit TeBG (sensitivity less than or equal to 150 pg). 3alpha- and 3beta-androstanediol were similarly assayed using human TeBG (sensitivity approximately 150 pg). Androsterone was reduced with NaBH4 and the resulting 3alpha-androstanediol was assayed using human TeBG (sensitivity approximately 200 pg). Inter- and intra-assay variations were less than 10% for radioimmunoassays and less than 16% for competitive protein-binding assays over the entire dose response curve.

Can H-aggregates serve as light-harvesting antennae? Triplet-triplet energy transfer between excited aggregates and monomer thionine in aerosol-OT solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Das, S.; Kamat, P.V.

1999-01-07

The cationic dye thionine undergoes slow dissolution in aerosol-OT (AOT) containing solutions of heptane and toluene. By controlling the ratio of [dye]/[AOT], it is possible to obtain varying amounts of monomer, dimer, and higher order aggregates (trimer) in dilute dye solutions. The thionine aggregates exhibit characteristic absorption maxima at 565 and 530 nm for the dimer and trimer forms, respectively. The singlet excited states of these dye aggregates are short-lived ({tau} = 40--63 ps) as they undergo efficient intersystem crossing to generate the triplet excited states. Triplet energy transfer from the excited dye aggregates to monomeric thionine molecules was observedmore » upon excitation with a 532 nm laser pulse. Pulse radiolysis experiments, in which the excited triplet states were generated indirectly, also confirm the finding that the triplet energy cascades down from excited trimer to dimer to monomeric dye. These studies demonstrate the possibility of using H-type dye aggregates as antenna molecules to harvest light energy whereby the aggregate molecules absorb light in different spectral regions and subsequently transfer energy to the monomeric dye.« less

Chemical and Sensory Characterization of Oxidative Changes in Roasted Almonds Undergoing Accelerated Shelf Life.

PubMed

Franklin, Lillian M; Chapman, Dawn M; King, Ellena S; Mau, Mallory; Huang, Guangwei; Mitchell, Alyson E

2017-03-29

In almonds, there is no standard method for detecting oxidative changes and little data correlating consumer perception with chemical markers of rancidity. To address this, we measured peroxide values (PV), free fatty acid values (FFAs), conjugated dienes, tocopherols, headspace volatiles, and consumer hedonic response in light roasted (LR) and dark roasted (DR) almonds stored under conditions that promote rancidity development over 12 months. Results demonstrate that, although rancidity develops at different rates in LR and DR almonds, consumer liking was not significantly different between LR and DR almonds. Average hedonic ratings of almonds were found to fall below a designated acceptable score of 5 ("neither like nor dislike") by 6 months of storage. This did not correspond with recommended industry rejection standard of PV < 5 mequiv peroxide/kg oil and FFA < 1.5% oleic. FFAs remain well below <1.5% oleic during storage, indicating that FFAs are not a good marker of rancidity in roasted almonds stored in low humidity environments. Regression of consumer liking to concentration of rancidity indicators revealed that selected headspace volatiles, including heptanal, octanal, nonanal, 2-octenal, 2-heptanone, 2-pentylfuran, hexanal, and pentanal, had a better correlation with liking than did nonvolatile indicators.

Can green solvents be alternatives for thermal stabilization of collagen?

PubMed

Mehta, Ami; Rao, J Raghava; Fathima, Nishter Nishad

2014-08-01

"Go Green" campaign is gaining light for various industrial applications where water consumption needs to be reduced. To resolve this, industries have adopted usage of green, organic solvents, as an alternative to water. For leather making, tanning industry consumes gallons of water. Therefore, for adopting green solvents in leather making, it is necessary to evaluate its influence on type I collagen, the major protein present in the skin matrix. The thermal stability of collagen from rat tail tendon fiber (RTT) treated with seven green solvents namely, ethanol, ethyl lactate, ethyl acetate, propylene carbonate, propylene glycol, polyethylene glycol-200 and heptane was determined using differential scanning calorimetry (DSC). Crosslinking efficiency of basic chromium sulfate and wattle on RTT in green solvents was determined. DSC thermograms show increase in thermal stability of RTT collagen against heat with green solvents (>78°C) compared to water (63°C). In the presence of crosslinkers, RTT demonstrated thermal stability >100°C in some green solvents, resulting in increased intermolecular forces between collagen, solvent and crosslinkers. The significant improvement in thermal stability of collagen potentiates the capability of green solvents as an alternative for water. Copyright © 2014 Elsevier B.V. All rights reserved.

Biotinylated vanadium and chromium sulfide nanoparticles as probes for colocalization of membrane proteins.

PubMed

Loukanov, Alexandre; Emin, Saim

2016-09-01

We report the microemulsion synthesis of vanadium and chromium sulfide nanoparticles (NPs) and their biological application as nanoprobes for colocalization of membrane proteins. Spherical V2 S3 and Cr2 S3 NPs were prepared in reverse microemulsion droplets, as nanoreactors, obtained by the surfactant sodium bis(2-ethylhexyl) sulfosuccinate (AOT) in nonpolar organic phase (heptane). Electron microscopic data indicated that the size distribution of the nanoparticles was uniform with an average diameter between 3 ÷ 5 nm. The prepared hydrophobic nanocrystals were transferred in aqueous phase by surface cap exchange of AOT with biotin-dihydrolipoic ligands. This substitution allows the nanoparticles solubility in aqueous solutions and confer their bioactivity. In addition, we report the conjugation procedure between α-Lipoic acid (LA) and biotin (abbreviated as biotin-LA). The biotin-LA structure was characterized by 1D and 2D NMR spectroscopy. The biotinylated vanadium and chromium sulfide nanoparticles were tested as probes for colocalization of glutamate receptors on sodium-dodecyl-sulfate-digested replica prepared from rat hippocampus. The method suggests their high labeling efficiency for study of membrane biological macromolecules. Microsc. Res. Tech. 79:799-805, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Non-aqueous phase liquid spreading during soil vapor extraction

PubMed Central

Kneafsey, Timothy J.; Hunt, James R.

2010-01-01

Many non-aqueous phase liquids (NAPLs) are expected to spread at the air – water interface, particularly under non-equilibrium conditions. In the vadose zone, this spreading should increase the surface area for mass transfer and the efficiency of volatile NAPL recovery by soil vapor extraction (SVE). Observations of spreading on water wet surfaces led to a conceptual model of oil spreading vertically above a NAPL pool in the vadose zone. Analysis of this model predicts that spreading can enhance the SVE contaminant recovery compared to conditions where the liquid does not spread. Experiments were conducted with spreading volatile oils hexane and heptane in wet porous media and capillary tubes, where spreading was observed at the scale of centimeters. Within porous medium columns up to a meter in height containing stagnant gas, spreading was less than ten centimeters and did not contribute significantly to hexane volatilization. Water film thinning and oil film pinning may have prevented significant oil film spreading, and thus did not enhance SVE at the scale of a meter. The experiments performed indicate that volatile oil spreading at the field scale is unlikely to contribute significantly to the efficiency of SVE. PMID:14734243

Identification and biotransformation of aliphatic hydrocarbons during co-composting of sewage sludge-Date Palm waste using Pyrolysis-GC/MS technique.

PubMed

El Fels, Loubna; Lemee, Laurent; Ambles, André; Hafidi, Mohamed

2016-08-01

The behavior of aliphatic hydrocarbons during co-composting of sewage sludge activated with palm tree waste was studied for 6 months using Py-GC/MS. The main aliphatic compounds represented as doublet alkenes/alkanes can be classified into three groups. The first group consists of 11 alkenes (undecene, tridecene, pentadecene, hexadecene, heptadecene, octadecene, nonadecene, eicosene, uncosene, docosene, tricosene) and 15 alkanes (heptane, octane, nonane, decane, undecane, dodecane, tetradecane, pentadecane, heptadecane, octadecane, nonadecane, eicosane, uncosane, docosane, and tricosane), which remain stable during the co-composting process. The stability of these compounds is related to their recalcitrance behavior. The second group consists of five alkenes (heptene, octene, nonene, decene, dodecene) and tridecane as a single alkane that decreases during co-composting. The decrease in these compounds is the combined result of their metabolism and their conversion into other compounds. The third group is constituted with tetradecene and hexadecane that increase during composting, which could be explained by accumulation of these compounds, which are released by the partial breakdown of the substrate. As a result, these molecules are incorporated or adsorbed in the structure of humic substances.

[Technology upgrades and exposure to chemical agents: results of the PPTP study in the footwear industry].

PubMed

Gianoli, Enrica; Brusoni, Daniela; Cornaggia, Nicoletta; Saretto, Gianni

2012-01-01

In the present work the chemical compositions of the products used in shoes manufacturing are reported. The data were collected over the period 2004-2007 in 156 shoe factories in Vigevano area during a study aiming the evaluation of safety conditions and occupational exposure to hazardous chemicals of the employees. The study was part of a regional project for "Occupational cancer prevention in the footwear industry". In the first phase of the study an information form on production cycle, products used and their composition was filled during preliminary audit. In the second phase of the study an in depth qualitative/quantitative evaluation of professional exposure was conducted in 13 selected shoe factories. Data analysis showed the increase in use of water-based adhesives at expense of solvent-based adhesives, the reduction to less than 3.5 weight %, and up to 1 weight %, of n-hexane concentration in solvent mixtures, the increase in use of products containing less hazardous ketones, esters, cyclohexane and heptane. Only in very few cases, products containing from 4 to 12 weight% of toluene were used. These data attest a positive trend in workers risks prevention in shoes industry.

Catalytic cracking of model compounds of bio-oil over HZSM-5 and the catalyst deactivation.

PubMed

Chen, Guanyi; Zhang, Ruixue; Ma, Wenchao; Liu, Bin; Li, Xiangping; Yan, Beibei; Cheng, Zhanjun; Wang, Tiejun

2018-08-01

The catalytic cracking upgrading reactions over HZSM-5 of different model compounds of bio-oil have been studied with a self-designed fluid catalytic cracking (FCC) equipment. Typical bio-oil model compounds, such as acetic acid, guaiacol, n-heptane, acetol and ethyl acetate, were chosen to study the products distribution, reaction pathway and deactivation of catalysts. The results showed: C 6 -C 8 aromatic hydrocarbons, C 2 -C 4 olefins, C 1 -C 5 alkanes, CO and CO 2 were the main products, and the selectivity of olefins was: ethylene>propylene>butylene. Catalyst characterization methods, such as FI-IR, TG-TPO and Raman, were used to study the deactivation mechanism of catalysts. According to the catalyst characterization results, a catalyst deactivation mechanism was proposed as follows: Firstly, the precursor which consisted of a large number of long chain saturated aliphatic hydrocarbons and a small amount CC of aromatics formed on the catalyst surface. Then the active sites of catalysts had been covered, the coke type changed from thermal coke to catalytic coke and gradually blocked the channels of the molecular sieve, which accelerated the deactivation of catalyst. Copyright © 2018 Elsevier B.V. All rights reserved.

n-Aldehydes (C6-C10) in snow samples collected at the high alpine research station Jungfraujoch during CLACE 5

NASA Astrophysics Data System (ADS)

Sieg, K.; Starokozhev, E.; Fries, E.; Sala, S.; Püttmann, W.

2009-03-01

Samples of freshly fallen snow were collected at the high alpine research station Jungfraujoch, Switzerland, during the Cloud and Aerosol Characterization Experiments (CLACE) 5 in February and March 2006. Sampling was carried out on the Sphinx platform. Headspace-solid-phase-dynamic extraction (HS-SPDE) combined with gas chromatography/mass spectrometry (GC/MS) was used to quantify C6-C10 n-aldehydes in the snow samples. The most abundant n-aldehyde was n-hexanal (median concentration 1.324 μg L-1) followed by n-nonanal, n-decanal, n-octanal and n-heptanal (median concentrations 1.239, 0.863, 0.460, and 0.304 μg L-1, respectively). A wide range of concentrations was found among individual snow samples, even for samples taken at the same time. Higher median concentrations of all n-aldehydes were observed when air masses reached Jungfraujoch from the north-northwest in comparison to air masses arriving from the southeast-southwest. Results suggest that the n-aldehydes detected most likely are of direct and indirect biogenic origin, and that they entered the snow through the particle phase.

Computational solvent system screening for the separation of tocopherols with centrifugal partition chromatography using deep eutectic solvent-based biphasic systems.

PubMed

Bezold, Franziska; Weinberger, Maria E; Minceva, Mirjana

2017-03-31

Tocopherols are a class of molecules with vitamin E activity. Among those, α-tocopherol is the most important vitamin E source in the human diet. The purification of tocopherols involving biphasic liquid systems can be challenging since these vitamins are poorly soluble in water. Deep eutectic solvents (DES) can be used to form water-free biphasic systems and have already proven applicable for centrifugal partition chromatography separations. In this work, a computational solvent system screening was performed using the predictive thermodynamic model COSMO-RS. Liquid-liquid equilibria of solvent systems composed of alkanes, alcohols and DES, as well as partition coefficients of α-tocopherol, β-tocopherol, γ-tocopherol, and σ-tocopherol in these biphasic solvent systems were calculated. From the results the best suited biphasic solvent system, namely heptane/ethanol/choline chloride-1,4-butanediol, was chosen and a batch injection of a tocopherol mixture, mainly consisting of α- and γ-tocopherol, was performed using a centrifugal partition chromatography set up (SCPE 250-BIO). A separation factor of 1.74 was achieved for α- and γ-tocopherol. Copyright © 2017 Elsevier B.V. All rights reserved.

Centrifuge in Free Fall: Combustion at Partial Gravity

NASA Technical Reports Server (NTRS)

Ferkul, Paul

2017-01-01

A centrifuge apparatus is developed to study the effect of variable acceleration levels in a drop tower environment. It consists of a large rotating chamber, within which the experiment is conducted. NASA Glenn Research Center 5.18-second Zero-Gravity Facility drop tests were successfully conducted at rotation rates up to 1 RPS with no measurable effect on the overall Zero-Gravity drop bus. Arbitrary simulated gravity levels from zero to 1-g (at a radius of rotation 30 cm) were produced. A simple combustion experiment was used to exercise the capabilities of the centrifuge. A total of 23 drops burning a simulated candle with heptane and ethanol fuel were performed. The effect of gravity level (rotation rate) and Coriolis force on the flames was observed. Flames became longer, narrower, and brighter as gravity increased. The Coriolis force tended to tilt the flames to one side, as expected, especially as the rotation rate was increased. The Zero-Gravity Centrifuge can be a useful tool for other researchers interested in the effects of arbitrary partial gravity on experiments, especially as NASA embarks on future missions which may be conducted in non-Earth gravity.

Aspects of Cool-Flame Supported Droplet Combustion in Microgravity

NASA Technical Reports Server (NTRS)

Nayagam, Vedha; Dietrich, Daniel L.; Williams, Forman A.

2015-01-01

Droplet combustion experiments performed on board the International Space Station have shown that normal-alkane fuels with negative temperature coefficient (NTC) chemistry can support quasi-steady, low-temperature combustion without any visible flame. Here we review the results for n-decane, n-heptane, and n-octane droplets burning in carbon dioxidehelium diluted environments at different pressures and initial droplet sizes. Experimental results for cool-flame burning rates, flame standoff ratios, and extinction diameters are compared against simplified theoretical models of the phenomenon. A simplified quasi-steady model based on the partial-burning regime of Lin predicts the burning rate, and flame standoff ratio reasonably well for all three normal alkanes. The second-stage cool-flame burning and extinction following the first-stage hot-flame combustion, however, shows a small dependence on the initial droplet size, thus deviating from the quasi-steady results. An asymptotic model that estimates the oxygen depletion by the hot flame and its influence on cool-flame burning rates is shown to correct the quasi-steady results and provide a better comparison with the measured burning-rate results.This work was supported by the NASA Space Life and Physical Sciences Research and Applications Program and the International Space Station Program.

Molecular thermodynamics for prevention of asphaltene precipitation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Jianzhong; Prausnitz, J.M.

Crude petroleum is a complex mixture of compounds with different chemical structures and molecular weights. Asphaltenes, the heaviest and most polar fraction of crude oil, are insoluble in normal alkanes such as n-heptane, but they are soluble in aromatic solvents such as toluene. The molecular nature of asphaltenes and their role in production and processing of crude oils have been the topic of numerous studies. Under some conditions, asphaltenes precipitate from a petroleum fluid, causing severe problems in production and transportation Our research objective is to develop a theoretically based, but engineering-oriented, molecular-thermodynamic model which can describe the phase behaviormore » of asphaltene precipitation in petroleum fluids, to provide guidance for petroleum-engineering design and production. In this progress report, particular attention is given to the potential of mean force between asphaltene molecules in a medium of asphaltene-free solvent. This potential of mean force is derived using the principles of colloid science. It depends on the properties of asphaltene and those of the solvent as well as on temperature and pressure. The effect of a solvent on interactions between asphaltenes is taken into account through its density and through its molecular dispersion properties.« less

Superior anticancer activity is demonstrated by total extract of Curcuma longa L. as opposed to individual curcuminoids separated by centrifugal partition chromatography.

PubMed

Kukula-Koch, Wirginia; Grabarska, Aneta; Łuszczki, Jarogniew; Czernicka, Lidia; Nowosadzka, Ewa; Gumbarewicz, Ewelina; Jarząb, Agata; Audo, Gregoire; Upadhyay, Shakti; Głowniak, Kazimierz; Stepulak, Andrzej

2018-05-01

Three curcuminoids: bisdemethoxycurcumin, demethoxycurcumin, and curcumin from turmeric were successfully separated by a high capacity solvent system composed of heptane: chloroform: methanol: water mixture (5: 6: 3: 2 v/v/v/v) tailored for centrifugal partition chromatographs at K-values of 0.504, 1.057, 1.644, respectively. These three ferulic acid derivatives obtained at a purity rate exceeding 95% were analysed by an HPLC-MS spectrometer. Turmeric extract inhibited the proliferation/viability of A549 human lung cancer, HT29 colon cancer, and T98G glioblastoma cell lines in (3-[4,5-dimethylthiazol-2-yl]-2,5-diphenyltetrazolium bromide) tetrazolium reduction assay (MTT). Single curcuminoids significantly decreased the viability/proliferation of lung cancer cells in a dose-dependent manner. However, total extract displayed the superior anticancer activity in the investigated cell lines. Crude extract in combination with cisplatin augmented the decrease in the viability of cancer cells compared with single compound treatment in A549 lung cancer cells. Total extract of Curcuma longa could be regarded as being more effective against lung cancer cells in vitro than its separated compounds. Copyright © 2018 John Wiley & Sons, Ltd.

Antibacterial, anti-inflammatory, and antioxidant effects of Yinzhihuang injection.

PubMed

Liu, Juan; Qiu, Hong; Zhu, Zhaorong; Zou, Tangbin

2015-01-01

The Yinzhihuang injection, a traditional Chinese medicine, has been the recent target of increasing interest due to its anti-inflammatory properties. The molecular basis by which Yinzhihuang injection could cure Riemerella anatipestifer (RA) serositis in ducks is unclear. This study evaluated the antibacterial, anti-inflammatory and antioxidant effects of Yinzhihuang injection, using disease models of RA-induced infectious serositis in ducks and heptane-induced inflammation in mice and rats. The duck mortality rate was reduced from 60% to 20% and both the inflammatory response and histological damage were ameliorated by treatment with Yinzhihuang injection (0.02 g/kg). Further studies indicated that superoxide dismutase (SOD), nitric oxide synthase (NOS), and inducible nitric oxide synthase (iNOS) were elevated while malondialdehyde (MDA), nitric oxide (NO) and RA growth were inhibited when the ducks were treated by Yinzhihuang injection. In addition, Yinzhihuang injection (0.04 g/ml) effectively inhibited xylene-induced auricle swelling in mice, (demonstrating an inhibition rate of 35.21%), egg albumen-induced paw metatarsus swelling in rats, (demonstrating an inhibition rate of 22.30%), and agar-induced formation of granulation tissue. These results suggest that Yinzhihuang injection ameliorates RA-induced infectious serositis in ducks by modulation of inflammatory mediators and antioxidation.

Droplet evaporation and combustion in a liquid-gas multiphase system

NASA Astrophysics Data System (ADS)

Muradoglu, Metin; Irfan, Muhammad

2017-11-01

Droplet evaporation and combustion in a liquid-gas multiphase system are studied computationally using a front-tracking method. One field formulation is used to solve the flow, energy and species equations with suitable jump conditions. Both phases are assumed to be incompressible; however, the divergence-free velocity field condition is modified to account for the phase change at the interface. Both temperature and species gradient driven phase change processes are simulated. Extensive validation studies are performed using the benchmark cases: The Stefan and the sucking interface problems, d2 law and wet bulb temperature comparison with the psychrometric chart values. The phase change solver is then extended to incorporate the burning process following the evaporation as a first step towards the development of a computational framework for spray combustion. We used detailed chemistry, variable transport properties and ideal gas behaviour for a n-heptane droplet combustion; the chemical kinetics being handled by the CHEMKIN. An operator-splitting approach is used to advance temperature and species mass fraction in time. The numerical results of the droplet burning rate, flame temperature and flame standoff ratio show good agreement with the experimental and previous numeric.

Perturbation Effects on a Supercritical C7H16/N2 Mixing Layer

NASA Technical Reports Server (NTRS)

Okongo'o, Nora; Bellan, Josette

2008-01-01

A computational-simulation study has been presented of effects of perturbation wavelengths and initial Reynolds numbers on the transition to turbulence of a heptane/nitrogen mixing layer at supercritical pressure. The governing equations for the simulations were the same as those of related prior studies reported in NASA Tech Briefs. Two-dimensional (2D) simulations were performed with initially im posed span wise perturbations whereas three-dimensional (3D) simulations had both streamwise and spanwise initial perturbations. The 2D simulations were undertaken to ascertain whether perturbations having the shortest unstable wavelength obtained from a linear stability analysis for inviscid flow are unstable in viscous nonlinear flows. The goal of the 3D simulations was to ascertain whether perturbing the mixing layer at different wavelengths affects the transition to turbulence. It was found that transitions to turbulence can be obtained at different perturbation wavelengths, provided that they are longer than the shortest unstable wavelength as determined by 2D linear stability analysis for the inviscid case and that the initial Reynolds number is proportionally increased as the wavelength is decreased. The transitional states thus obtained display different dynamic and mixture characteristics, departing strongly from the behaviors of perfect gases and ideal mixtures.

[Determination of serum or plasma alpha-tocopherol by high performance liquid chromatography: optimization of operative models].

PubMed

Jezequel-Cuer, M; Le Moël, G; Mounié, J; Peynet, J; Le Bizec, C; Vernet, M H; Artur, Y; Laschi-Loquerie, A; Troupel, S

1995-01-01

A previous multicentric study set up by the Société française de biologie clinique has emphasized the usefulness of a standardized procedure for the determination by high performance liquid chromatography of alpha-tocopherol in serum or plasma. In our study, we have tested every step of the different published procedures: internal standard adduct, lipoprotein denaturation and vitamin extraction. Reproducibility of results was improved by the use of tocol as an internal standard when compared to retinol or alpha-tocopherol acetates. Lipoprotein denaturation was more efficient with ethanol addition than with methanol and when the ethanol/water ratio was > or = 0.7. Use of n-hexane or n-heptane gave the same recovery of alpha-tocopherol. When organic solvent/water ratio was > or = 1, n-hexane enabled to efficiently extract, in a one-step procedure, the alpha-tocopherol from both normo and hyperlipidemic sera. Performances of the selected procedure were: detection limit: 0.5 microM--linear range: 750 microM--within run coefficient of variation: 2.03%--day to day: 4.76%. Finally, this pluricentric study allows us to propose an optimised procedure for the determination of alpha-tocopherol in serum or plasma.

Phototransformation of azoxystrobin fungicide in organic solvents. Photoisomerization vs. photodegradation.

PubMed

Chastain, Jeoffrey; ter Halle, Alexandra; de Sainte Claire, Pascal; Voyard, Guillaume; Traikïa, Mounir; Richard, Claire

2013-12-01

Azoxystrobin is a systemic fungicide that has a tendency to accumulate at the surface of crop leaves or inside their cuticle where it undergoes photodegradation. Its photochemistry was investigated in n-heptane and isopropanol to mimic the polarity of wax leaves. Using analytical and kinetic data, we demonstrate that azoxystrobin (isomer E) undergoes efficient photoisomerization into the isomer Z with a quantum yield of 0.75 ± 0.08. This value is 30-fold higher than that reported in aqueous solution. The photoisomerization of isomer Z into azoxystrobin is more efficient with a chemical yield of 0.95 ± 0.1. In addition, a pseudo photostationary equilibrium is reached when the ratio [azoxystrobin]/[isomer Z] is 2.0 ± 0.1. Photodegradation also takes place from azoxystrobin (quantum yield = 0.073 ± 0.008). Photoproducts mainly arise from bond cleavage between rings and from demethylation of the ether with or without saturation of the acrylate double bond. Theoretical calculations were undertaken to investigate the photoisomerization mechanism and the solvent effect. These data show that the photochemical reactivity of azoxystrobin is enhanced when the solvent polarity decreases and thus should be significant in leaf waxes.

Investigation of aggregation in solvent extraction of lanthanides by acidic extractants (organophosphorus and naphthenic acid)

USGS Publications Warehouse

Zhou, N.; Wu, J.; Yu, Z.; Neuman, R.D.; Wang, D.; Xu, G.

1997-01-01

Three acidic extractants (I) di(2-ethylhexyl) phosphoric acid (HDEHP), (II) 2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester (HEHPEHE) and (III) naphthenic acid were employed in preparing the samples for the characterization of the coordination structure of lanthanide-extractant complexes and the physicochemical nature of aggregates formed in the organic diluent of the solvent extraction systems. Photo correlation spectroscopy (PCS) results on the aggregates formed by the partially saponified HDEHP in n-heptane showed that the hydrodynamic radius of the aggregates was comparable to the molecular dimensions of HDEHP. The addition of 2-octanol into the diluent, by which the mixed solvent was formed, increased the dimensions of the corresponding aggregates. Aggregates formed from the lanthanide ions and HDEHP in the organic phase of the extraction systems were found very unstable. In the case of naphthenic acid, PCS data showed the formation of w/o microemulsion from the saponified naphthenic acid in the mixed solvent. The extraction of lanthanides by the saponified naphthenic acid in the mixed solvent under the given experimental conditions was a process of destruction of the w/o microemulsion. A possible mechanism of the breakdown of the w/o microemulsion droplets is discussed.

Volatile organic chemicals of a shore-dwelling cyanobacterial mat community.

PubMed

Evans, W G

1994-02-01

The main components of a cyanobacterial mat community of a hypersaline lake shore consist of edaphic, mat-forming strains (ecophenes), and littoral strains ofOscillatoria animalis Agardh andO. subbrevis Schmidle, other microorganisms associated with these cyanobacteria, several species ofBembidion (Carabidae: Coleoptera), and two halophytic flowering plants:Puccinellia nuttalliana (salt meadow grass) andSalicornia europaea rubra (samphire). The volatile organic compounds of this community are a blend of those emitted by each of these components such as the C17 alka(e)nes, geosmin, 2-methylisoborneol,β-cyclocitral,β-ionone, dimethyl sulfide, and dimethyl trisulfide of cyanobacteria and associated microorganisms; alcohols, esters, and aldehydes usually associated with flowering plants; and possibly some insect-derived esters, particularly isopropyl tetradecanoate. The dominant compounds were: C11, C13, C15, and C17 alka(e)nes, methyl esters of C16 and C18:2 acids, isopropyl tetradecanoate, heptanal, 3-octanone and 2-nonanone, the acyclic terpene linalool, and the alcohols 1-heptanol, 1-hexanol, 1-octanol, 3-hexen-1-ol, and 2-octen-1-ol. It is concluded that this community may be distinguished from related communities by its repertoire of volatile organic compounds.

Structure and phase transitions of asphaltenes in solutions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Tar, M.M. de; Sheu, E.Y.; Storm, D.A.

The authors investigated the rheological properties of two vacuum resid fractions in a series of solvents. The authors measured the viscosity as a function of concentration and temperature respectively. In this study, two aspects were focused: (1) the concentration dependence of viscosity for the pentane soluble fractions in a series of n-alkane solvents for study of the particle structure, and (2) the temperature dependence of viscosity of the heptane insoluble fraction in toluene at various concentrations for the study of the phase transitions. From their results it was found that all the systems studied are Newtonian. The results for (1)more » show that the particles are approximately spherical and as the carbon number of the n-alkane solvent increases, the quality of the solvent increases, thereby increasing the particle solvation. This result is consistent with that reported in a recent paper by Ali and Saleem. Also, the particles were found to behave similarly to colloidal particles. As for (2), a glass-like transition was observed at 50% concentration (0.31 volume fraction) with glass transition temperature at about 254 K, while no structural or phase transitions were observed for concentrations below 50%.« less

Thermostable NADP+-Dependent Medium-Chain Alcohol Dehydrogenase from Acinetobacter sp. Strain M-1: Purification and Characterization and Gene Expression in Escherichia coli

PubMed Central

Tani, Akio; Sakai, Yasuyoshi; Ishige, Takeru; Kato, Nobuo

2000-01-01

NADPH-dependent alkylaldehyde reducing enzyme, which was greatly induced by n-hexadecane, from Acinetobacter sp. strain M-1 was purified and characterized. The purified enzyme had molecular masses of 40 kDa as determined by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and 160 kDa as determined by gel filtration chromatography. The enzyme, which was shown to be highly thermostable, was most active toward n-heptanal and could use n-alkylaldehydes ranging from C2 to C14 and several substituted benzaldehydes, including the industrially important compounds cinnamyl aldehyde and anisaldehyde, as substrates. The alrA gene coding for this enzyme was cloned, and its nucleotide sequence was determined. The deduced amino acid sequence encoded by the alrA gene exhibited homology to the amino acid sequences of zinc-containing alcohol dehydrogenases from various sources. The gene could be highly expressed in Escherichia coli, and the product was purified to homogeneity by simpler procedures from the recombinant than from the original host. Our results show that this enzyme can be used for industrial bioconversion of useful alcohols and aldehydes. PMID:11097895

A molecular dynamics study of components of the ginger (Zingiber officinale) extract inside human acetylcholinesterase: implications for Alzheimer disease.

PubMed

Cuya, Teobaldo; Baptista, Leonardo; Celmar Costa França, Tanos

2017-11-23

Components of ginger (Zingiber officinale) extracts have been described as potential new drug candidates against Alzheimer disease (AD), able to interact with several molecular targets related to the AD treatment. However, there are very few theoretical studies in the literature on the possible mechanisms of action by which these compounds can work as potential anti-AD drugs. For this reason, we performed here docking, molecular dynamic simulations and mmpbsa calculations on four components of ginger extracts former reported as active inhibitors of human acetylcholinesterase (HssAChE), and compared our results to the known HssAChE inhibitor and commercial drug in use against AD, donepezil (DNP). Our findings points to two among the compounds studied: (E)-1,7-bis(4-hydroxy-3-methoxyphenyl)hept-4-en-3-on and 1-(3,4-dihydroxy-5-methoxyphenyl)-7-(4-hydroxy-3- ethoxyphenyl) heptane-3,5-diyl diacetate, as promising new HssAChE inhibitors that could be as effective as DNP. We also mapped the binding of the studied compounds in the different binding pockets inside HssAChE and established the preferred interactions to be favored in the design of new and more efficient inhibitors.

[Volatile organic compounds concentrations and sources inside new air-conditioned bus].

PubMed

You, Ke-Wei; Ge, Yun-Shan; Qian, Yi-Xin; Liu, Wei; Feng, Bo; Zhang, Yan-Ni; Ning, Zhan-Wu; Hu, Bin; Zhao, Shou-Tang

2008-05-01

The distributing profile and concentration level inside new air-conditioned buses with 53 seats have been determined using the method of thermal desorption-capillary GC/MS under vehicle static conditions. Compounds were identified from their mass spectral data by using US National Institute of Standards and Technology (NIST02). The total numbers of identified components were 33 inside buses, including alkenes (15,45.4%), aromatic compounds (9,27.3%), alcohols (4,12.1%), ketones (3,9.1%) and esters (2,6.1%), especially in the range of C6-C10. The top 5 compounds measured inside buses were decane (8.01 mg/m3), 3-methylhexane (7.10 mg/m3), heptane (5.10 mg/m3), isoheptane (4.20 mg/m3) and 1-Methyl-3-ethylbenzene (3.56 mg/m3), and total volatile organic compounds (TVOC) > 52.5 mg/m3. The main sources of in-vehicle hydrocarbons and aromatic compounds comes from cabin components and interior trim materials (e.g., sealants, carpets, adhesives, paints, leather, plastics, PU foam and PE foam) that may retain certain VOCs during manufacturing, and/or emit these compounds over an extended period of time from off-gassing, aging-related breakdown products, heating/cooling and so on.

The effect of soot modeling on thermal radiation in buoyant turbulent diffusion flames

NASA Astrophysics Data System (ADS)

Snegirev, A.; Kokovina, E.; Tsoy, A.; Harris, J.; Wu, T.

2016-09-01

Radiative impact of buoyant turbulent diffusion flames is the driving force in fire development. Radiation emission and re-absorption is controlled by gaseous combustion products, mainly CO2 and H2O, and by soot. Relative contribution of gas and soot radiation depends on the fuel sooting propensity and on soot distribution in the flame. Soot modeling approaches incorporated in big commercial codes were developed and calibrated for momentum-dominated jet flames, and these approaches must be re-evaluated when applied to the buoyant flames occurring in fires. The purpose of this work is to evaluate the effect of the soot models available in ANSYS FLUENT on the predictions of the radiative fluxes produced by the buoyant turbulent diffusion flames with considerably different soot yields. By means of large eddy simulations, we assess capability of the Moss-Brooks soot formation model combined with two soot oxidation submodels to predict methane- and heptane-fuelled fires, for which radiative flux measurements are available in the literature. We demonstrate that the soot oxidation models could be equally important as soot formation ones to predict the soot yield in the overfire region. Contribution of soot in the radiation emission by the flame is also examined, and predicted radiative fluxes are compared to published experimental data.

Photocatalytic events of CdSe quantum dots in confined media. Electrodic behavior of coupled platinum nanoparticles.

PubMed

Harris, Clifton; Kamat, Prashant V

2010-12-28

The electrodic behavior of platinum nanoparticles (2.8 nm diameter) and their role in influencing the photocatalytic behavior of CdSe quantum dots (3.4 nm diameter) has been evaluated by confining both nanoparticles together in heptane/dioctyl sulphosuccinate/water reverse micelles. The particles spontaneously couple together within the micelles via micellar exchange processes and thus facilitate experimental observation of electron transfer reactions inside the water pools. Electron transfer from CdSe to Pt is found to occur with a rate constant of 1.22 × 10(9) s(-1). With the use of methyl viologen (MV(2+)) as a probe molecule, the role of Pt in the photocatalytic process is established. Ultrafast oxidation of the photogenerated MV(+•) radicals indicates that Pt acts as an electron sink, scavenging electrons from MV(+•) with a rate constant of 3.1 × 10(9) s(-1). The electron transfer between MV(+•) and Pt, and a drastically lower yield of MV(+•) under steady state irradiation, confirms the ability of Pt nanoparticles to discharge electrons quickly. The kinetic details of photoinduced processes in CdSe-Pt assemblies and the electrodic behavior of Pt nanoparticles provide important information for the development of light energy conversion devices.

Organic solvent tolerance of an α-amylase from haloalkaliphilic bacteria as a function of pH, temperature, and salt concentrations.

PubMed

Pandey, Sandeep; Singh, S P

2012-04-01

A haloalkaliphilic bacterium was isolated from salt-enriched soil of Mithapur, Gujarat (India) and identified as Bacillus agaradhaerens Mi-10-6₂ based on 16S rRNA sequence analysis (NCBI gene bank accession, GQ121032). The bacterium was studied for its α-amylase characteristic in the presence of organic solvents. The enzyme was quite active and it retained considerable activity in 30% (v/v) organic solvents, dodecane, decane, heptane, n-hexane, methanol, and propanol. At lower concentrations of solvents, the catalysis was quite comparable to control. Enzyme catalysis at wide range of alkanes and alcohol was an interesting finding of the study. Mi-10-6₂ amylase retained activity over a broader alkaline pH range, with the optimal pH at 10-11. Two molars of salt was optimum for catalysis in the presence of most of the tested solvents, though the enzyme retained significant activity even at 4 M salt. With dodecane, the optimum temperature shifted from 50 °C to 60 °C, while the enzyme was active up to 80 °C. Over all, the present study focused on the effect of organic solvents on an extracellular α-amylase from haloalkaliphilic bacteria under varying conditions of pH, temperature, and salt.

Validation of an LES Model for Soot Evolution against DNS Data in Turbulent Jet Flames

NASA Astrophysics Data System (ADS)

Mueller, Michael

2012-11-01

An integrated modeling approach for soot evolution in turbulent reacting flows is validated against three-dimensional Direct Numerical Simulation (DNS) data in a set of n-heptane nonpremixed temporal jet flames. As in the DNS study, the evolution of the soot population is described statistically with the Hybrid Method of Moments (HMOM). The oxidation of the fuel and formation of soot precursors are described with the Radiation Flamelet/Progress Variable (RFPV) model that includes an additional transport equation for Polycyclic Aromatic Hydrocarbons (PAH) to account for the slow chemistry governing these species. In addition, the small-scale interactions between soot, chemistry, and turbulence are described with a presumed subfilter PDF approach that accounts for the very large spatial intermittency characterizing soot in turbulent reacting flows. The DNS dataset includes flames at three different Damköhler numbers to study the influence of global mixing rates on the evolution of PAH and soot. In this work, the ability of the model to capture these trends quantitatively as Damköhler number varies is investigated. In order to reliably assess the LES approach, the LES is initialized from the filtered DNS data after an initial transitional period in an effort to minimize the hydrodynamic differences between the DNS and the LES.

Experiments on Induction Times of Diesel-Fuels and its Surrogates

NASA Astrophysics Data System (ADS)

Eigenbrod, Christian; Reimert, Manfredo; Marks, Guenther; Rickmers, Peter; Klinkov, Konstantin; Moriue, Osamu

Aiming for as low polluting combustion control as possible in Diesel-engines or gas-turbines, pre-vaporized and pre-mixed combustion at low mean temperature levels marks the goal. Low-est emissions of nitric-oxides are achievable at combustion temperatures associated to mixture ratios close to the lean flammability limit. In order to prevent local mixture ratios to be below the flammability limit (resulting in flame extinction or generation of unburned hydrocarbons and carbon-monoxide) or to be richer than required (resulting in more nitric-oxide than possi-ble), well-stirred conditioning is required. The time needed for spray generation, vaporization and turbulent mixing is limited through the induction time to self-ignition in a hot high-pressure ambiance. Therefore, detailed knowledge about the autoignition of fuels is a pre-requisit. Experiments were performed at the Bremen drop tower to investigate the self-ignition behavior of single droplets of fossil-Diesel oil, rapeseed-oil, Gas-to-Liquid (GTL) synthetic Diesel-oil and the fossil Diesel surrogates n-heptane, n-tetradecane, 50 n-tetradecane/ 50 1-methylnaphthalene as well as on the GTL-surrogates n-tetradecane / bicyclohexyl and n-tetradecane / 2,2,4,4,6,8,8-heptamethylnonane (iso-cetane). The rules for selection of the above fuels and the experimental results are presented and dis-cussed.

Organic Rankine Cycle for Residual Heat to Power Conversion in Natural Gas Compressor Station. Part II: Plant Simulation and Optimisation Study

NASA Astrophysics Data System (ADS)

Chaczykowski, Maciej

2016-06-01

After having described the models for the organic Rankine cycle (ORC) equipment in the first part of this paper, this second part provides an example that demonstrates the performance of different ORC systems in the energy recovery application in a gas compressor station. The application shows certain specific characteristics, i.e. relatively large scale of the system, high exhaust gas temperature, low ambient temperature operation, and incorporation of an air-cooled condenser, as an effect of the localization in a compressor station plant. Screening of 17 organic fluids, mostly alkanes, was carried out and resulted in a selection of best performing fluids for each cycle configuration, among which benzene, acetone and heptane showed highest energy recovery potential in supercritical cycles, while benzene, toluene and cyclohexane in subcritical cycles. Calculation results indicate that a maximum of 10.4 MW of shaft power can be obtained from the exhaust gases of a 25 MW compressor driver by the use of benzene as a working fluid in the supercritical cycle with heat recuperation. In relation to the particular transmission system analysed in the study, it appears that the regenerative subcritical cycle with toluene as a working fluid presents the best thermodynamic characteristics, however, require some attention insofar as operational conditions are concerned.

Observed trends in ambient concentrations of C 2-C 8 hydrocarbons in the United Kingdom over the period from 1993 to 2004

NASA Astrophysics Data System (ADS)

Dollard, G. J.; Dumitrean, P.; Telling, S.; Dixon, J.; Derwent, R. G.

Hourly measurements of up to 26 C 2-C 8 hydrocarbons have been made at eight urban background sites, three urban-industrial sites, a kerbside and a rural site in the UK from 1993 onwards up until the end of December 2004. Average annual mean benzene and 1,3-butadiene concentrations at urban background locations have declined at about -20% per year and the observed declines have exactly mimicked the inferred declines in benzene and 1,3-butadiene emissions over the same period. Ninety-day rolling mean concentrations of ethylene, propylene, n- and i-butane, n- and i-pentane, isoprene and propane at urban and rural sites have also declined steadily by between -10% and -30% per year. Rolling mean concentrations of acetylene, 2- and 3-methylpentane, n-hexane, n-heptane, cis- and trans-but-2-ene, cis- and trans-pent-2-ene, toluene, ethylbenzene and o-, m- and p-xylene at a roadside location in London have all declined at between -14% and -21% per year. These declines demonstrate that motor vehicle exhaust catalysts and evaporative canisters have effectively and efficiently controlled vehicular emissions of hydrocarbons in the UK. Urban ethane concentrations arising largely from natural gas leakage have remained largely unchanged over this same period.

Rational Design of Hyperbranched Nanowire Systems for Tunable Superomniphobic Surfaces Enabled by Atomic Layer Deposition

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bielinski, Ashley R.; Boban, Mathew; He, Yang

2017-01-24

A method for tunable control of geometry in hyperbranched ZnO nanowire (NW) systems is reported, which enables the rational design and fabrication of superomniphobic surfaces. Branched NWs with tunable density and orientation were grown via a sequential hydrothermal process, in which atomic layer deposition (ALD) was used for NW seeding, disruption of epitaxy, and selective blocking of NW nucleation. This approach allows for the rational design and optimization of three-level hierarchical structures, in which the geometric parameters of each level of hierarchy can be individually controlled. We demonstrate the coupled relationships between geometry and contact angle for a variety ofmore » liquids, which is supported by mathematical models of structural superomniphobicity. The highest performing superomniphobic surface was designed with three levels of hierarchy and achieved the following advancing/receding contact angles, water: 172°/170°, hexadecane: 166°/156°, octane: 162°/145°, and heptane: 160°/130°. Low surface tension liquids were shown to bounce off the surface from a height of 7 cm without breaking through and wetting. This approach demonstrates the power of ALD as an enabling technique for hierarchical materials by design, spanning the macro, micro, and nano length scales.« less

Interactions of agonists with an allosteric antagonist at muscarinic acetylcholine M2 receptors.

PubMed

Lanzafame, A; Christopoulos, A; Mitchelson, F

1996-11-28

The interaction of heptane-1,7-bis(dimethyl-3'-phthalimidopropylammonium bromide) (C7/3'-phth), with several agonists, was investigated at the muscarinic M2 receptor in guinea-pig left atria. C7/3'-phth shifted concentration-response curves for the agonists, carbachol, oxotremorine-M and (+)-cis-dioxolane, to the right in a parallel fashion. Arunlakshana-Schild regressions of the data yielded slopes significantly different to unity, suggesting non-competitive antagonism. Non-linear regression analysis, using an equation based on allosteric modulation, gave quantitative estimates of co-operativity (alpha values) and the dissociation constant of C7/3'-phth (KB). In all cases, the KB estimates for C7/3'-phth were not significantly different. Increasing the carbachol contact time 10-fold did not significantly influence the KB or the alpha value obtained with C7/3'-phth. Changing from Krebs to Tyrode solution did not significantly alter the KB for C7/3'-phth, although alpha values obtained were consistently lower in Tyrode solution, suggesting that the allosteric action may be sensitive to buffer composition. A 4-fold higher degree of negative, heterotropic co-operativity between C7/3'-phth and agonists than between C7/3'-phth and competitive antagonists was also found.

Differentiation between decomposed remains of human origin and bigger mammals.

PubMed

Rosier, E; Loix, S; Develter, W; Van de Voorde, W; Cuypers, E; Tytgat, J

2017-08-01

This study is a follow-up study in the search for a human specific marker in the decomposition where the VOC-profile of decomposing human, pig, lamb and roe remains were analyzed using a thermal desorber combined with a gas chromatograph coupled to a mass spectrometer in a laboratory environment during 6 months. The combination of 8 previously identified human and pig specific compounds (ethyl propionate, propyl propionate, propyl butyrate, ethyl pentanoate, 3-methylthio-1-propanol, methyl(methylthio)ethyl disulfide, diethyl disulfide and pyridine) was also seen in these analyzed mammals. However, combined with 5 additional compounds (hexane, heptane, octane, N-(3-methylbutyl)- and N-(2-methylpropyl)acetamide) human remains could be separated from pig, lamb and roe remains. Based on a higher number of remains analyzed, as compared with the pilot study, it was no longer possible to rely on the 5 previously proposed esters to separate pig from human remains. From this follow-up study reported, it was found that pyridine is an interesting compound specific to human remains. Such a human specific marker can help in the training of cadaver dogs or in the development of devices to search for human remains. However, further investigations have to verify these results. Copyright © 2017 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

A comparison of gray and non-gray modeling approaches to radiative transfer in pool fire simulations.

PubMed

Krishnamoorthy, Gautham

2010-10-15

Decoupled radiative heat transfer calculations of 30 cm-diameter toluene and heptane pool fires are performed employing the discrete ordinates method. The composition and temperature fields within the fires are created from detailed experimental measurements of soot volume fractions based on absorption and emission, temperature statistics and correlations found in the literature. The measured temperature variance data is utilized to compute the temperature self-correlation term for modeling turbulence-radiation interactions. In the toluene pool fire, the presence of cold soot near the fuel surface is found to suppress the average radiation feedback to the pool surface by 27%. The performances of four gray and three non-gray radiative property models for the gases are also compared. The average variations in radiative transfer predictions due to differences in the spectroscopic and experimental databases employed in the property model formulations are found to be between 10% and 20%. Clear differences between the gray and non-gray modeling strategies are seen when the mean beam length is computed based on traditionally employed geometric relations. Therefore, a correction to the mean beam length is proposed to improve the agreement between gray and non-gray modeling in simulations of open pool fires. 2010 Elsevier B.V. All rights reserved.

Characterization of volatile aroma compounds in different brewing barley cultivars.

PubMed

Dong, Liang; Hou, Yingmin; Li, Feng; Piao, Yongzhe; Zhang, Xiao; Zhang, Xiaoyu; Li, Cheng; Zhao, Changxin

2015-03-30

Beer is a popular alcoholic malt beverage resulting from fermentation of the aqueous extract of malted barley with hops. The aroma of brewing barley impacts the flavor of beer indirectly, because some flavor compounds or their precursors in beer come from the barley. The objectives of this research were to study volatile profiles and to characterize odor-active compounds of brewing barley in order to determine the variability of the aroma composition among different brewing barley cultivars. Forty-one volatiles comprising aldehydes, ketones, alcohols, organic acids, aromatic compounds and furans were identified using solid phase microextraction combined with gas chromatography/mass spectrometry, among which aldehydes, alcohols and ketones were quantitatively in greatest abundance. Quantitative measurements performed by means of solvent extraction and calculation of odor activity values revealed that acetaldehyde, 2-methylpropanal, 3-methylbutanal, 2-methylbutanal, hexanal, heptanal, octanal, nonanal, 3-methyl-1-butanol, cyclopentanol, 2,3-butanedione, 2,3-pentanedione, 2-heptanone, acetic acid, ethyl acetate, 2-pentylfuran and benzeneacetaldehyde, whose concentrations exceeded their odor thresholds, could be considered as odor-active compounds of brewing barley. Principal component analysis was employed to evaluate the differences among cultivars. The results demonstrated that the volatile profile based on the concentrations of aroma compounds enabled good differentiation of most barley cultivars. © 2014 Society of Chemical Industry.

Nanoscale carbon materials from hydrocarbons pyrolysis: Structure, chemical behavior, utilisation for non-aqueous supercapacitors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Savilov, Serguei V., E-mail: savilov@chem.msu.ru; Strokova, Natalia E.; Ivanov, Anton S.

Highlights: • N-doped and regular carbon nanomaterials were obtained by pyrolitic technique. • Dynamic vapor sorption of different solvents reveals smaller S{sub BET} values. • Steric hindrance and specific chemical interactions are the reasons for this. • Nitrogen doping leads to raise of capacitance and coulombic efficiency with non-aqueous N-containing electrolyte. - Abstract: This work systematically studies adsorption properties of carbon nanomaterials that are synthesized through hydrocarbons that is a powerful technique to fabricate different kinds of carbon materials, e.g., nanotubes, nanoshells, onions, including nitrogen substituted. The adsorption properties of the as-synthesized carbons are achieved by low temperature nitrogen adsorptionmore » and organic vapors sorption. Heptane, acetonitrile, water, ethanol, benzene and 1-methylimidazole, which are of great importance for development of supercapacitors, are used as substrates. It is discovered that while nitrogen adsorption reveals a high specific surface area, this parameter for most of organic compounds is rather small depending not only on the size of its molecule but also on chemical interactions for a pair adsorbent–adsorbate. The experimental values of heat of adsorption for carbon and N-substituted structures, when Coulomb cross-coupling of nitrogen atoms in adsorbent and adsorbate takes place, confirms this supposition.« less

Influence of pulsed electric field treatments on the volatile compounds of milk in comparison with pasteurized processing.

PubMed

Zhang, Sha; Yang, Ruijin; Zhao, Wei; Hua, Xiao; Zhang, Wenbin; Zhang, Zhong

2011-01-01

Effects of pulsed electric field (PEF) treatments on the volatile profiles of milk were studied and compared with pasteurized treatment of high temperature short time (HTST) (75 °C, 15 s). Volatile compounds were extracted by solid-phase micro-extraction (SPME) and identified by gas chromatography/mass spectrometry (GC-MS) and gas chromatography-olfactometry (GC-O). A total of 37 volatile compounds were determined by GC-MS, and 19 volatile compounds were considered to be major contributors to the characteristic flavor of milk samples. PEF treatment resulted in an increase in aldehydes. Milk treated with PEF at 30 kV/cm showed the highest content of pentanal, hexanal, and nonanal, while heptanal and decanal contents were lower than in pasteurized milk, but higher than in raw milk. All the methyl ketones detected in PEF milk were lower than in pasteurized milk. No significant differences in acids (acetic acid, butanoic acid, hexanoic acid, octanoic acid, and decanoic acid), lactones, and alcohols were observed between pasteurized and PEF-treated samples; however, 2(5H)-furanone was only detected in PEF-treated milk. Although GC-MS results showed that there were some volatile differences between pasteurized and PEF-treated milk, GC-O data showed no significant difference between the 2 samples.

Staining human lymphocytes and onion root cell nuclei with madder root.

PubMed

Cücer, N; Guler, N; Demirtas, H; Imamoğlu, N

2005-01-01

We performed staining experiments on cells using natural dyes and different mordants using techniques that are used for wool and silk dyeing. The natural dye sources were madder root, daisy, corn cockle and yellow weed. Ferrous sulfate, copper sulfate, potassium tartrate, urea, potassium aluminum sulfate and potassium dichromate were used as mordants. Distilled water, distilled water plus ethanol, heptane, and distilled water plus methanol were used as solvents. All dye-mordant-solvent combinations were studied at pH 2.4, 3.2 and 4.2. The generic staining procedure was to boil 5-10 onion roots or stimulated human lymphocyte (SHL) preparations in a dye bath on a hot plate. Cells were examined at every half hour. For multicolor staining, madder-dyed lymphocytes were decolorized, then stained with Giemsa. The AgNOR technique was performed following the decolorization of Giemsa stained lymphocytes. Good results were obtained for both onion root cells and lymphocytes that were boiled for 3 h in a dye bath that included 4 g madder root, 4 g ferrous sulfate as mordant in 50 ml of 1:1 (v/v) methanol:distilled water. The pH was adjusted to 4.2 with 6 ml acetic acid. We conclude that madder root has potential as an alternative dye for staining biological materials.

Increase in volatilization of organic compounds using air sparging through addition in alcohol in a soil-water system.

PubMed

Chao, Huan-Ping; Hsieh, Lin-Han Chiang; Tran, Hai Nguyen

2018-02-15

This study developed a novel method to promote the remediation efficiency of air sparging. According to the enhanced-volatilization theory presented in this study, selected alcohols added to groundwater can highly enhance the volatilization amounts of organic compounds with high Henry's law constants. In this study, the target organic compounds consisted of n-hexane, n-heptane, benzene, toluene, 1,1,2-trichloroethane, and tetrachloroethene. n-pentanol, n-hexanol, and n-heptanol were used to examine the changes in the volatilization amounts of organic compounds in the given period. Two types of soils with high and low organic matter were applied to evaluate the transport of organic compounds in the soil-water system. The volatilization amounts of the organic compounds increased with increasing alcohol concentrations. The volatilization amounts of the test organic compounds exhibited a decreasing order: n-heptanol>n-hexanol>n-pentanol. When 10mg/L n-heptanol was added to the system, the maximum volatilization enhancement rate was 18-fold higher than that in distilled water. Samples of soil with high organic matter might reduce the volatilization amounts by a factor of 5-10. In the present study, the optimal removal efficiency for aromatic compounds was approximately 98%. Copyright © 2017 Elsevier B.V. All rights reserved.

A multi-year study of hepatic biomarkers in coastal fishes from the Gulf of Mexico after the Deepwater Horizon Oil Spill.

PubMed

Smeltz, Marci; Rowland-Faux, Laura; Ghiran, Céline; Patterson, William F; Garner, Steven B; Beers, Alan; Mièvre, Quentin; Kane, Andrew S; James, Margaret O

2017-08-01

Following the 2010 Gulf of Mexico oil spill, concerns were raised regarding exposure of fish to crude oil components, particularly polycyclic aromatic hydrocarbons (PAHs). This three year study examined hepatic enzymes in post-mitochondrial supernatant fractions from red snapper (Lutjanus campechanus) and gray triggerfish (Balistes capriscus) collected in the north central Gulf of Mexico between 2011 and 2014. Biomarker activities evaluated included benzo(a)pyrene hydroxylase (AHH), ethoxyresorufin O-deethylase (EROD), glutathione transferase (GST), and glutathione peroxidase (GPx). Mean EROD activity was higher in gray triggerfish (12.97 ± 7.15 pmol/min/mg protein [mean ± SD], n = 115) than red snapper (2.75 ± 1.92 pmol/min/mg protein, n = 194), p < 0.0001. In both species, EROD declined over time between 2011 and 2014. Declines in GST and GPx activities were also noted over this time period for both species. Gray triggerfish liver was fatty, and heptane extracts of the liver fat contained fluorescent substances with properties similar to known PAHs, however the origin of these PAHs is unknown. Copyright © 2017 Elsevier Ltd. All rights reserved.

Common Host-Derived Chemicals Increase Catches of Disease-Transmitting Mosquitoes and Can Improve Early Warning Systems for Rift Valley Fever Virus

PubMed Central

Tchouassi, David P.; Sang, Rosemary; Sole, Catherine L.; Bastos, Armanda D. S.; Teal, Peter E. A.; Borgemeister, Christian; Torto, Baldwyn

2013-01-01

Rift Valley fever (RVF), a mosquito-borne zoonosis, is a major public health and veterinary problem in sub-Saharan Africa. Surveillance to monitor mosquito populations during the inter-epidemic period (IEP) and viral activity in these vectors is critical to informing public health decisions for early warning and control of the disease. Using a combination of field bioassays, electrophysiological and chemical analyses we demonstrated that skin-derived aldehydes (heptanal, octanal, nonanal, decanal) common to RVF virus (RVFV) hosts including sheep, cow, donkey, goat and human serve as potent attractants for RVFV mosquito vectors. Furthermore, a blend formulated from the four aldehydes and combined with CO2-baited CDC trap without a light bulb doubled to tripled trap captures compared to control traps baited with CO2 alone. Our results reveal that (a) because of the commonality of the host chemical signature required for attraction, the host-vector interaction appears to favor the mosquito vector allowing it to find and opportunistically feed on a wide range of mammalian hosts of the disease, and (b) the sensitivity, specificity and superiority of this trapping system offers the potential for its wider use in surveillance programs for RVFV mosquito vectors especially during the IEP. PMID:23326620

Emulsification of oil in water as affected by different parameters.

PubMed

Baloch, Musa Kaleem; Hameed, Gulzar

2005-05-15

The aim of this investigation was to develop a basic understanding of the emulsification process by considering simple systems such as n-hexane, n-heptane, n-decane, and kerosene oil in water. The technique employed for the purpose was ultrasonification. The effect of ultrasonification time, chain length, viscosity, surface tension, oil content, and ionic strength of the media on the quality of emulsion has been studied. The emulsions were viewed through microscope to measure the number, size, and size distribution of droplets. Quantification of turbidity and viscosity was also used to characterize the emulsions. It has been found that the number and size of the droplets vary with the time of ultrasonification, contents of oils, molecular mass of the oils, and ionic strength of the media, and hence the quality of the emulsion is influenced by these parameters. The droplet size decreases, whereas the number of drops increases with the time of emulsification, approaching an optimum distribution at about 15 min of ultrasonification. Further, the increase in the molecular mass of the oil increases the size of the droplets and hence decreases the stability of the emulsion. The addition of electrolytes encourages coalescence and enhances the instability in the system. The results are in accord with the equations proposed by us.

Instabilities in the electric Freedericksz state of the twist-bend nematic liquid crystal CB7CB.

PubMed

Krishnamurthy, Kanakapura S; Kanakala, Madhu B; Yelamaggad, Channabasaveshwar V; Kleman, Maurice

2018-06-22

We report on the instabilities in the Freedericksz state of the twist-bend nematic (NTB) liquid crystal 1'',7''-bis(4-cyanobiphenyl-4'-yl)heptane (CB7CB). The quasi homeotropic NTB state, into which a planar (untwisted or 90°-twisted) nematic CB7CB layer transits under a strong electric field, is found to be unstable despite the material being dielectrically positive. Close to the NTB melting point, destabilization occurs through the formation of metastable toric focal conic domains (TFCDs) that, in time, transform into parabolic focal conic domains (PFCDs) with the confocal parabolae in vertical planes through the layer normal. This transformation occurs by a novel process of continued dissociation of TFCDs. We outline how the extended Volterra process could help in a general appreciation of focal conic defects in the NTB phase. At relatively lower temperatures, stripes develop competingly with TFCDs. Identifiable as oily streaks, they are both localized and polarity sensitive; they form close to the substrates; and in low frequency square wave fields, they get suppressed at the cathode and augmented at the anode at each polarity switch. The study also dwells on the N-NTB-N sandwich region, found between the N and NTB states under a small temperature gradient.

Separation and preconcentration of Ag(I) in aqueous samples by flotation as an ion-associate using iodide and ferroin followed the determination by flame atomic absorption spectrometry.

PubMed

Hosseini, Mohammad Saeid; Hashemi-Moghaddam, Hamid; Kardan-Moghaddam, Gholamreza

2007-01-01

A simple method for separation/preconcentration and determination of Ag(I) in aqueous samples is described. The method is based on formation of an ion-associate between Ag(I)-iodide complex and ferroin, which can be floated at the interface of the aqueous/n-heptane phases. The flotation process was carried out using 500-ml aliquot of the aqueous solution and the floated layer was dissolved in 5 ml of 1 M HNO3 containing methanol (50% v/v) as the solvent. The Ag(I) content was then determined by flame atomic absorption spectrometry (FAAS). The method so could be considered as an enrichment process, was achieved to a quantitative feature, when the pH of the solution was adjusted to 4 and the concentrations of iodide and ferroin were about 3.2 x 10(-4) M and 6.25 x 10(-5) M, respectively. The LOD and RSD (n = 7) were obtained 1.0 x 10(-8) M and 2.4%, respectively. It was found that a large number of cations and anions even at high considerably foreign ion/Ag(I) ratios were not interfered. The method was applied satisfactorily to recovery of Ag(I) from different aqueous samples.

Effects of gamma irradiation on the yields of volatile extracts of Angelica gigas Nakai

NASA Astrophysics Data System (ADS)

Seo, Hye-Young; Kim, Jun-Hyoung; Song, Hyun-Pa; Kim, Dong-Ho; Byun, Myung-Woo; Kwon, Joog-Ho; Kim, Kyong-Su

2007-11-01

The study was carried out to determine the effects of gamma irradiation on the volatile flavor components including essential oils, of Angelica gigas Nakai. The volatile organic compounds from non- and irradiated A. gigas Nakai at doses of 1, 3, 5, 10 and 20 kGy were extracted by a simultaneous steam distillation and extraction (SDE) method and identified by GC/MS analysis. A total of 116 compounds were identified and quantified from non- and irradiated A. gigas Nakai. The major volatile compounds were identified 2,4,6-trimethyl heptane, α-pinene, camphene, α-limonene, β-eudesmol, α-murrolene and sphatulenol. Among these compounds, the amount of essential oils in non-irradiated sample were 77.13%, and the irradiated samples at doses of 1, 3, 5, 10 and 20 kGy were 84.98%, 83.70%, 83.94%, 82.84% and 82.58%, respectively. Oxygenated terpenes such as β-eudesmol, α-eudesmol, and verbenone were increased after irradiation but did not correlate with the irradiation dose. The yields of active substances such as essential oil were increased after irradiation; however, the yields of essential oils and the irradiation dose were not correlated. Thus, the profile of composition volatiles of A. gigas Nakai did not change with irradiation.

Determination of methylglyoxal-bis(guanylhydrazone) in body fluids by ion-pair chromatography.

PubMed

Roboz, J; Wu, K T; Hart, R D

1980-01-01

Methylglyoxal-bis(guanylhydrazone), Methyl-G, is a potent antineoplastic agent currently undergoing Phase l clinical trials. Serum, ascitic and pleural fluids, and urine are deproteinized with methanol, supernatant is evaporated, residue is redissolved in the eluent, lipids are removed with carbon tetrachloride, and an aliquot of the aqueous layer injected into the chromatograph. Ethylglyoxal-bis(guanylhydrazone) (Ethyl-G) is the internal standard. The mobile phase is a mixture of an aqueous buffer (containing 0.004 M heptane and pentane sulfonic acid, 90%:10%, buffered to pH 3.5) and methanol (68%:32%). The ion-pair complex is retained on a micro Bondapak C18 column, eluted with a flow of 2.0 mL/min. Absorbance is measured at 280 nm. Detectability: 30 ng/mL (0.11 micro M) in serum, ascitic and pleural fluids, 300 ng/mL (1.1 micro M) in urine. Calibration curves (peak height ratios of Methyl-G/Ethyl-G plotted against known drug concentrations) were linear in the 0.1-30 microg/mL range. Correlation coefficinets were 0.999; coefficients of variation for reproducibility were less than 5%. Residual blood levels of Methyl-G persist for several days. Methyl-G was found to pass into ascitic fluid.

Combustion characteristics in the transition region of liquid fuel sprays

NASA Technical Reports Server (NTRS)

Cernansky, N. P.; Namer, I.; Tidona, R. J.

1986-01-01

A number of important effects have been observed in the droplet size transition region in spray combustion systems. In this region, where the mechanism of flame propagation is transformed from diffusive to premixed dominated combustion, the following effects have been observed: (1) maxima in burning velocity; (2) extension of flammability limits; (3) minima in ignition energy; and (4) minima in NOx formation. A monodisperse aerosol generator has been used to form and deliver a well controlled liquid fuel spray to the combustion test section where measurements of ignition energy have been made. The ignition studies were performed on monodisperse n-heptane sprays at atmospheric pressure over a range of equivalence ratios and droplet diameters. A capacitive discharge spark ignition system was used as the ignition source, providing independent control of spark energy and duration. Preliminary measurements were made to optimize spark duration and spark gap, optimum conditions being those at which the maximum frequency or probability of ignition was observed. Using the optimum electrode spacing and spark duration, the frequency of ignition was determined as a function of spark energy for three overall equivalence ratios (0.6, 0.8, and 1.0) and for initial droplet diameters of 25, 40, 50, 60, and 70 micro m.

Determination of the dispersion constant in a constrained vapor bubble thermosyphon

NASA Technical Reports Server (NTRS)

Dasgupta, Sunando; Plawsky, Joel L.; Wayner, Peter C., Jr.

1995-01-01

The isothermal profiles of the extended meniscus in a quartz cuvette were measured in a gravitational field using an image analyzing interferometer which is based on computer enhanced video microscopy of the naturally occurring interference fringes. The experimental results for heptane and pentane menisci were analyzed using the extended Young Laplace Equation. These isothermal results characterized the interfacial force field in-siru at the start of the heat transfer experiments by quantifying the dispersion constant, which is a function of the liquid-solid system and cleaning procedures. The experimentally obtained values of the disjoining pressure and the dispersion constants were compared to that predicted from the DLP theory and good agreements were obtained. The measurements are critical to the subsequent non-isothermal experiments because one of the major variables in the heat sink capability of the Constrained Vapor Bubble Thermosyphon, CVBT, is the dispersion constant. In all previous studies of micro heat pipes the value of the dispersion constant has been 'estimated'. One of the major advantages of the current glass cell is the ability to view the extended meniscus at all times. Experimentally, we find that the extended Young-Laplace Equation is an excellent model for the force field at the solid-liquid-vapor interfaces.

Selective adsorption of thiophene and 1-benzothiophene on metal-ion-exchanged zeolites in organic medium.

PubMed

Xue, Mei; Chitrakar, Ramesh; Sakane, Kohji; Hirotsu, Takahiro; Ooi, Kenta; Yoshimura, Yuji; Feng, Qi; Sumida, Naoto

2005-05-15

Adsorption of the organic sulfur compounds thiophene (TP) and 1-benzothiophene (1-BTP) in an organic model solution of hydrodesulfurizated gasoline (heptane with 1 wt% toluene and 0.156 mM (5 ppmw as sulfur) TP or 1-BTP) was studied by a batch method at 80 degrees C using metal-ion-exchanged Y-zeolites. Although NaY-zeolite or its acid-treated material rarely adsorbed the organic sulfur compounds, NaY-zeolites exchanged with Ag+, Cu2+, and Ce3+ ions and NH(4)Y-zeolites exchanged with Ce3+ ions showed markedly high adsorptive capacities for TP and 1-BTP. The sulfur uptake increased in the order CuY-zeolite(Na)

Effect of e-beam irradiation and microwave heating on the fatty acid composition and volatile compound profile of grass carp surimi

NASA Astrophysics Data System (ADS)

Zhang, Hongfei; Wang, Wei; Wang, Haiyan; Ye, Qingfu

2017-01-01

In this study, we evaluated the effects of e-beam irradiation（1-7 kGy） and irradiation coupled to microwave heating (e-I-MC, 70 °C internal temperature) on the fatty acid composition and volatile compound profile of grass carp surimi. Compared to control samples, e-beam irradiation generated three novel volatile compounds (heptane, 2,6-dimethyl-nonane, and dimethyl disulfide) and increased the relative proportions of alcohols, aldehydes, and ketones. Meanwhile, e-I-MC significantly increased aldehyde levels and generated five heterocyclic compounds along with these three novel compounds. No significant difference in volatile compounds were detected in e-I-MC samples with increasing irradiation dose (p>0.05), comparing to the control group. E-beam irradiation at 5 and 7 kGy increased the levels of saturated fatty acids (SFAs) and decreased the levels of unsaturated fatty acids (p≤0.05), but did not affect the content of trans fatty acid levels (p>0.05). Irradiation, which had no significant effects on (Eicosapentaenoic acid) EPA, decreased (Docose Hexaenoie Acid) DHA levels. In the e-I-MC group, SFA levels increased and PUFA levels decreased. Additionally, MUFA levels were unaffected and trans fatty acid levels increased slightly following e-I-MC.

Sensitive detection of n-alkanes using a mixed ionization mode proton-transfer-reaction mass spectrometer

NASA Astrophysics Data System (ADS)

Amador-Muñoz, Omar; Misztal, Pawel K.; Weber, Robin; Worton, David R.; Zhang, Haofei; Drozd, Greg; Goldstein, Allen H.

2016-11-01

Proton-transfer-reaction mass spectrometry (PTR-MS) is a technique that is widely used to detect volatile organic compounds (VOCs) with proton affinities higher than water. However, n-alkanes generally have a lower proton affinity than water and therefore proton transfer (PT) by reaction with H3O+ is not an effective mechanism for their detection. In this study, we developed a method using a conventional PTR-MS to detect n-alkanes by optimizing ion source and drift tube conditions to vary the relative amounts of different primary ions (H3O+, O2+, NO+) in the reaction chamber (drift tube). There are very few studies on O2+ detection of alkanes and the mixed mode has never been proposed before. We determined the optimum conditions and the resulting reaction mechanisms, allowing detection of n-alkanes from n-pentane to n-tridecane. These compounds are mostly emitted by evaporative/combustion process from fossil fuel use. The charge transfer (CT) mechanism observed with O2+ was the main reaction channel for n-heptane and longer n-alkanes, while for n-pentane and n-hexane the main reaction channel was hydride abstraction (HA). Maximum sensitivities were obtained at low E / N ratios (83 Td), low water flow (2 sccm) and high O2+ / NO+ ratios (Uso = 180 V). Isotopic 13C contribution was taken into account by subtracting fractions of the preceding 12C ion signal based on the number of carbon atoms and the natural abundance of 13C (i.e., 5.6 % for n-pentane and 14.5 % for n-tridecane). After accounting for isotopic distributions, we found that PT cannot be observed for n-alkanes smaller than n-decane. Instead, protonated water clusters of n-alkanes (M ṡ H3O+) species were observed with higher abundance using lower O2+ and higher water cluster fractions. M ṡ H3O+ species are probably the source for the M + H+ species observed from n-decane to n-tridecane. Normalized sensitivities to O2+ or to the sum of O2++ NO+ were determined to be a good metric with which to compare sensitivities for n-alkane detection between experiments. Double hydride abstraction was observed from the reaction with O2+. Sensitivity to CT increased with carbon chain length from n-pentane to n-dodecane, sensitivity to HA increased from n-heptane to n-dodecane and sensitivity to PT increased from n-decane to n-tridecane. Sensitivity to CT exponentially decreased with molecular ionization energy, which is inversely related to the carbon chain length. We introduce a calibrated fragmentation algorithm as a method to determine the concentrations of n-alkanes and demonstrate its effectiveness using a custom n-alkane mixture and a much more complex oil example representing perhaps the most difficult mixture available for application of the method. We define optimum conditions for using the mixed ionization mode to measure n-alkanes in conventional PTR-MS instruments regardless of whether they are equipped with switchable reagent ion (SRI) capabilities.

Determination of the hydrate structure of an isolated alcoholic OH in hydrophobic medium by infrared and near-infrared spectroscopy.

PubMed

Iwamoto, Reikichi; Kusanagi, Hiroshi

2009-05-07

This paper reports the structure of the hydrate complex of an isolated alcoholic OH, produced in a small amount in hydrophobic solution in heptane. The structure was determined from the changes, caused by hydration, in the infrared and near-infrared spectra of 2-nonanol in the solution. The changes were exhibited in the "difference" spectrum, in which the spectrum of the solution before hydration was subtracted from that after hydration. The difference spectrum showed a "plus" or "minus" peak at the frequency of the stretching band of a free OH, depending on whether the concentration was below or above about 2%(v/v), respectively. The plus peak appears because the OH stretching band of the isolated OH that acts as an acceptor does not change in frequency but significantly increases in intensity, in agreement with theoretical calculations. In contrast, the stretching band of an isolated OH that acts as a donor shifts downward. This shift decreases the intensity at the stretching frequency of a free OH, giving rise to a minus peak at the frequency in the difference spectrum. It was concluded that an isolated OH is hydrated in the manner as HO...HOH and OH...OH(2) at a concentration below and above about 2%, respectively, in the hydrophobic solution of 2-nonanol.

Ozone and Ozone By-Products in the Cabins of Commercial Aircraft

PubMed Central

Weisel, Clifford; Weschler, Charles J.; Mohan, Kris; Vallarino, Jose; Spengler, John D.

2013-01-01

The aircraft cabin represents a unique indoor environment due to its high surface-to-volume ratio, high occupant density and the potential for high ozone concentrations at cruising altitudes. Ozone was continuously measured and air was sampled on sorbent traps, targeting carbonyl compounds, on 52 transcontinental U.S. or international flights between 2008 and 2010. The sampling was predominantly on planes that did not have ozone scrubbers (catalytic converters). Peak ozone levels on aircraft without catalytic convertors exceeded 100 ppb, with some flights having periods of more than an hour when the ozone levels were > 75ppb. Ozone was greatly reduced on relatively new aircraft with catalytic convertors, but ozone levels on two flights whose aircraft had older convertors were similar to those on planes without catalytic convertors. Hexanal, heptanal, octanal, nonanal, decanal and 6-methyl-5-hepten-2-one (6-MHO) were detected in the aircraft cabin at sub- to low ppb levels. Linear regression models that included the log transformed mean ozone concentration, percent occupancy and plane type were statistically significant and explained between 18 and 25% of the variance in the mixing ratio of these carbonyls. Occupancy was also a significant factor for 6-MHO, but not the linear aldehydes, consistent with 6-MHO’s formation from the reaction between ozone and squalene, which is present in human skin oils. PMID:23517299

The behavior of exciplex decay processes and interplay of radiationless transition and preliminary reorganization mechanisms of electron transfer in loose and tight pairs of reactants.

PubMed

Kuzmin, Michael G; Soboleva, Irina V; Dolotova, Elena V

2007-01-18

Exciplex emission spectra and rate constants of their decay via internal conversion and intersystem crossing are studied and discussed in terms of conventional radiationless transition approach. Exciplexes of 9-cyanophenanthrene with 1,2,3-trimethoxybenzene and 1,3,5-trimethoxybenzene were studied in heptane, toluene, butyl acetate, dichloromethane, butyronitrile, and acetonitrile. A better description of spectra and rate constants is obtained using 0-0 transition energy and Gauss broadening of vibrational bands rather than the free energy of electron transfer and reorganization energy. The coincidence of parameters describing exciplex emission spectra and dependence of exciplex decay rate constants on energy gap gives the evidence of radiationless quantum transition mechanism rather than thermally activated medium reorganization mechanism of charge recombination in exciplexes and excited charge transfer complexes (contact radical ion pairs) as well as in solvent separated radical ion pairs. Radiationless quantum transition mechanism is shown to provide an appropriate description also for the main features of exergonic excited-state charge separation reactions if fast mutual transformations of loose and tight pairs of reactants are considered. In particular, very fast electron transfer (ET) in tight pairs of reactants with strong electronic coupling of locally excited and charge transfer states can prevent the observation of an inverted region in bimolecular excited-state charge separation even for highly exergonic reactions.

Chemical composition and antimicrobial activity of the essential oil from the edible aromatic plant Aristolochia delavayi.

PubMed

Li, Zhi-Jian; Njateng, Guy S S; He, Wen-Jia; Zhang, Hong-Xia; Gu, Jian-Long; Chen, Shan-Na; Du, Zhi-Zhi

2013-11-01

The essential oil obtained by hydrodistillation from the aerial parts of Aristolochia delavayi Franch. (Aristolochiaceae), a unique edible aromatic plant consumed by the Nakhi (Naxi) people in Yunnan, China, was investigated using GC/MS analysis. In total, 95 components, representing more than 95% of the oil composition, were identified, and the main constituents found were (E)-dec-2-enal (52.0%), (E)-dodec-2-enal (6.8%), dodecanal (3.35%), heptanal (2.88%), and decanal (2.63%). The essential oil showed strong inhibitory activity (96% reduction) of the production of bacterial volatile sulfide compounds (VSC) by Klebsiella pneumoniae, an effect that was comparable with that of the reference compound citral (91% reduction). Moreover, the antimicrobial activity of the essential oil and the isolated major compound against eight bacterial and six fungal strains were evaluated. The essential oil showed significant antibacterial activity against Providencia stuartii and Escherichia coli, with minimal inhibitory concentrations (MIC) ranging from 3.9 to 62.5 μg/ml. The oil also showed strong inhibitory activity against the fungal strains Trichophyton ajelloi, Trichophyton terrestre, Candida glabrata, Candida guilliermondii, and Cryptococcus neoformans, with MIC values ranging from 3.9 to 31.25 μg/ml, while (E)-dec-2-enal presented a lower antifungal activity than the essential oil. Copyright © 2013 Verlag Helvetica Chimica Acta AG, Zürich.

l-Type Amino Acid Transporter-1 Overexpression and Melphalan Sensitivity in Barrett's Adenocarcinoma1

PubMed Central

Lin, Jules; Raoof, Duna A; Thomas, Dafydd G; Greenson, Joel K; Giordano, Thomas J; Robinson, Gregory S; Bourner, Maureen J; Bauer, Christopher T; Orringer, Mark B; Beer, David G

2004-01-01

Abstract The L-type amino acid transporter-1 (LAT-1) has been associated with tumor growth. Using cDNA microarrays, overexpression of LAT-1 was found in 87.5% (7/8) of esophageal adenocarcinomas relative to 12 Barrett's samples (33% metaplasia and 66% dysplasia) and was confirmed in 100% (28/28) of Barrett's adenocarcinomas by quantitative reverse transcription polymerase chain reaction. Immunohistochemistry revealed LAT-1 staining in 37.5% (24/64) of esophageal adenocarcinomas on tissue microarray. LAT-1 also transports the amino acid-related chemotherapeutic agent, melphalan. Two esophageal adenocarcinoma and one esophageal squamous cell line, expressing LAT-1 on Western blot analysis, were sensitive to therapeutic doses of melphalan (P < .001). Simultaneous treatment with the competitive inhibitor, BCH [2-aminobicyclo-(2,1,1)-heptane-2-carboxylic acid], decreased sensitivity to melphalan (P < .05). In addition, confluent esophageal squamous cultures were less sensitive to melphalan (P < .001) and had a decrease in LAT-1 protein expression. Tumors from two esophageal adenocarcinoma cell lines grown in nude mice retained LAT-1 mRNA expression. These results demonstrate that LAT-1 is highly expressed in a subset of esophageal adenocarcinomas and that Barrett's adenocarcinoma cell lines expressing LAT-1 are sensitive to melphalan. LAT-1 expression is also retained in cell lines grown in nude mice providing a model to evaluate melphalan as a chemotherapeutic agent against esophageal adenocarcinomas expressing LAT-1. PMID:15068672

Isolation and identification of some unknown substances in disposable nitrile-butadiene rubber gloves used for food handling.

PubMed

Mutsuga, M; Wakui, C; Kawamura, Y; Maitani, T

2002-11-01

In Japan, disposable gloves made from nitrile-butadiene rubber (NBR) are frequently used in contact with foods. In a previous paper, we investigated substances migrating from various gloves made of polyvinyl chloride, polyethylene, natural rubber and NBR. Zinc di-n-butyldithiocarbamate (ZDBC), diethyldithiocarbamate (ZDEC) used as vulcanization accelerators, di(2-ethylhexyl)phthalate (DEHP) used as a plasticizer and many unknown compounds that migrated from NBR gloves into n-heptane were detected by GC/MS. In this paper, six unknown compounds were obtained from one kind of NBR glove by n-hexane extraction and each was isolated by silica gel chromatography. From the results of NMR and mass spectral analysis of the six unknown compounds, their structures are proposed as 1,4-dione-2,5-bis(1,1-dimethylpropyl)cyclohexadiene (1), 2-(1,1-dimethylethyl)-4-(1,1,3,3-tetra methylbutyl)phenol (2), 2,6-bis(1,1-dimethylethyl)-4-(1,1,3,3-tetramethylbutyl)phenol (3), 2,4-bis(1,1,3,3-tetramethylbutyl)phenol (4), 2-(1,1-dimethylethyl)4,6-bis(1,1,3,3-tetramethylbutyl)phenol (5) and 2,4,6-tris(1,1,3,3-tetramethylbutyl)phenol (6). Compound 1 was observed in five of the seven kinds of NBR gloves, and compounds 2-4 and 6, which are not listed in Chemical Abstract (CA), were present in four kinds of gloves.

Paraffin wax removal from metal injection moulded cocrmo alloy compact by solvent debinding process

NASA Astrophysics Data System (ADS)

Dandang, N. A. N.; Harun, W. S. W.; Khalil, N. Z.; Ahmad, A. H.; Romlay, F. R. M.; Johari, N. A.

2017-10-01

One of the most crucial and time consuming phase in metal injection moulding (MIM) process is “debinding”. These days, in metal injection moulding process, they had recounted that first debinding practice was depend on thermal binder degradation, which demanding more than 200 hours for complete removal of binder. Fortunately, these days world had introduced multi-stage debinding techniques to simplified the debinding time process. This research study variables for solvent debinding which are temperature and soaking time for samples made by MIM CoCrMo powder. Since wax as the key principal in the binder origination, paraffin wax will be removed together with stearic acid from the green bodies. Then, debinding process is conducted at 50, 60 and 70°C for 30-240 minutes. It is carried out in n-heptane solution. Percentage weight loss of the binder were measured. Lastly, scanning electron microscope (SEM) analysis and visual inspection were observed for the surface of brown compact. From the results, samples debound at 70°C exhibited a significant amount of binder loss; nevertheless, sample collapse, brittle surface and cracks were detected. But, at 60°C temperature and time of 4 hours proven finest results as it shows sufficient binder loss, nonappearance of surface cracks and easy to handle. Overall, binder loss is directly related to solvent debinding temperature and time.

Strategies for obtaining long constant-pressure test times in shock tubes

DOE PAGES

Campbell, Matthew Frederick; Parise, T.; Tulgestke, A. M.; ...

2015-09-22

Several techniques have been developed for obtaining long, constant-pressure test times in reflected shock wave experiments in a shock tube, including the use of driver inserts, driver gas tailoring, helium gas diaphragm interfaces, driver extensions, and staged driver gas filling. Here, we detail these techniques, including discussion on the most recent strategy, staged driver gas filling. Experiments indicate that this staged filling strategy increases available test time by roughly 20 % relative to single-stage filling of tailored driver gas mixtures, while simultaneously reducing the helium required per shock by up to 85 %. This filling scheme involves firstly mixing amore » tailored helium–nitrogen mixture in the driver section as in conventional driver filling and, secondly, backfilling a low-speed-of-sound gas such as nitrogen or carbon dioxide from a port close to the end cap of the driver section. Using this staged driver gas filling, in addition to the other techniques listed above, post-reflected shock test times of up to 0.102 s (102 ms) at 524 K and 1.6 atm have been obtained. Spectroscopically based temperature measurements in non-reactive mixtures have confirmed that temperature and pressure conditions remain constant throughout the length of these long test duration trials. Finally, these strategies have been used to measure low-temperature n-heptane ignition delay times.« less

Investigation on the light alkanes aromatization over Zn and Ga modified HZSM-5 catalysts in the presence of methane

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Qingyin; Zhang, Fengqi; Jarvis, Jack

The catalytic co-aromatization of methane and paraffin-rich raffinate oil was investigated along with hexane, heptane and octane as its model compounds over zinc and gallium modified ZSM-5 zeolite catalysts. The benzene, toluene and xylene (BTX) components derived from light alkane aromatization were highly promoted with the assistance of methane. The co-existence of Zn and Ga metal species has a positive effect on the formation of BTX components, whereas the individual metal loaded catalyst resulted in the production of heavy aromatics, suggesting that zinc and gallium have a synergistic effect on the formation of BTX under the methane environment. When concernedmore » with gaseous analysis, the introduced methane might interact with smaller intermediates and then transform into larger hydrocarbons. From the DRIFT observation, it was witnessed that the interaction between light alkane and methane occurred on the surface of the charged Zn-Ga/ZSM-5 catalyst. According to the comprehensive catalyst characterizations, the excellent catalytic performance may be closely associated with greatly dispersed metal species on the zeolite support, improved microporous characteristic, moderate Bronsted and increased Lewis acidic sites during the paraffin-rich liquid feedstock aromatization under methane environment. This research provides a promising pathway for the highly effective and profitable utilization of petrochemical resources and natural gas.« less

Comprehensive kinetic model for the low-temperature oxidation of hydrocarbons

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gaffuri, P.; Faravelli, T.; Ranzi, E.

1997-05-01

The oxidation chemistry in the low- and intermediate-temperature regimes (600--900 K) is important and plays a significant role in the overall combustion process. Autoignition in diesel engines as well as end-gas autoignition and knock phenomena in s.i. engines are initiated at these low temperatures. The low-temperature oxidation chemistry of linear and branched alkanes is discussed with the aim of unifying their complex behavior in various experimental systems using a single detailed kinetic model. New experimental data, obtained in a pressurized flow reactor, as well as in batch- and jet-stirred reactors, are useful for a better definition of the region ofmore » cool flames and negative temperature coefficient (NTC) for pure hydrocarbons from propane up to isooctane. Thermochemical oscillations and the NTC region of the reaction rate of the low-temperature oxidation of n-heptane and isooctane in a jet-stirred flow reactor are reproduced quite well by the model, not only in a qualitative way but in terms of the experimental frequencies and intensities of cool flames. Very good agreement is also observed for fuel conversion and intermediate-species formation. Irrespective of the experimental system, the same critical reaction steps always control these phenomena. The results contribute to the definition of a limited set of fundamental kinetic parameters that should be easily extended to model heavier alkanes.« less

A novel non-toxic xylene substitute (SBO) for histology.

PubMed

Kunhua, Wang; Chuming, Fan; Tao, Lai; Yanmei, Yang; Xin, Yang; Xiaoming, Zhang; Xuezhong, Guo; Xun, Lai

2012-01-01

Xylene has been generally used as a clearing and deparaffinizing agent in histology. Because of the potential toxic and flammable nature of xylene, its substitutes have been introduced into some laboratories. In this study, we introduced a novel, non-toxic xylene substitute (SBO), which was generated through a mixture of 86% of white oil No.2 and 14% of N-heptane. SBO had a high boiling point (188°C) and flash point (144°C) coupled with a scentless and decreased volatility. To compare the effectiveness of SBO and xylene in histology, a wide range of tissue samples from rats and human beings were processed in parallel in SBO and xylene, subjected to various staining procedures. Similar to the xylene-processed paraffin blocks, the SBO-processed counterparts were easy to section without any evidence of cell shrinkage. Assessment of the SBO-treated sections stained with hematoxylin-eosin revealed a good maintenance of cell morphology and structure, and a clear definition of the cytoplasm and the nucleus. Moreover, comparable good results were achieved between the SBO- and xylene-processed tissues in other histochemical and immunohistochemical stainings. Six-month clinical applications at one department of pathology supported the potentials of SBO as a xylene substitute. In conclusion, we suggest that SBO is a safe and efficient substitute of xylene and may probably replace xylene without losing valuable diagnostic information.

In Situ Monitoring and Modeling of the Solution-Mediated Polymorphic Transformation of Rifampicin: From Form II to Form I.

PubMed

Guo, Nannan; Hou, Baohong; Wang, Na; Xiao, Yan; Huang, Jingjing; Guo, Yanmei; Zong, Shuyi; Hao, Hongxun

2018-01-01

In this article, the solution-mediated polymorphic transformation of rifampicin was investigated and simulated in 3 solvents at 30°C. The solid-state form I and form II of rifampicin was characterized by powder X-ray diffraction, scanning electron microscopy, thermogravimetric analysis, Raman spectroscopy, and Fourier transform infrared spectroscopy (FTIR). To explore the relative stability, solubility data of form I and form II of rifampicin in butan-1-ol were determined using a dynamical method. In addition, Raman spectroscopy and focused beam reflectance measurement were used to in situ monitor the transformation of rifampicin from form II to form I. The liquid state concentration of rifampicin was measured by UV spectroscopic method. To investigate the effect of solvent on transformation, the transformation experiments were carried out in 3 solvents. Furthermore, a mathematical model was built to describe the kinetics of dissolution, nucleation, and growth processes during transformation by using experimental data. By combination of experimental and simulation results, it was found that the transformation process of rifampicin is controlled by dissolution of form II in heptane, whereas the transformation in hexane and octane was firstly controlled by dissolution of solid-state form and then controlled by growth of form I. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

Chemical transformation of 3-bromo-2,2-bis(bromomethyl)-propanol under basic conditions.

PubMed

Ezra, Shai; Feinstein, Shimon; Bilkis, Itzhak; Adar, Eilon; Ganor, Jiwchar

2005-01-15

The mechanism of the spontaneous decomposition of 3-bromo-2,2-bis(bromomethyl)propanol (TBNPA) and the kinetics of the reaction of the parent compound and two subsequent products were determined in aqueous solution at temperatures from 30 to 70 degrees C and pH from 7.0 to 9.5. TBNPA is decomposed by a sequence of reactions that form 3,3-bis(bromomethyl)oxetane (BBMO), 3-bromomethyl-3-hydroxymethyloxetane (BMHMO), and 2,6-dioxaspiro[3.3]-heptane (DOH), releasing one bromide ion at each stage. The pseudo-first-order rate constant of the decomposition of TBNPA increases linearlywith the pH. The apparent activation energy of this transformation (98+/-2 KJ/mol) was calculated from the change of the effective second-order rate constant with temperature. The pseudoactivation energies of BBMO and BMHMO were estimated to be 109 and 151 KJ/mol, respectively. Good agreement was found between the rate coefficients derived from changes in the organic molecules concentrations and those determined from the changes in the Br- concentrations. TBNPA is the most abundant semivolatile organic pollutant in the aquitard studied, and together with its byproducts they posess an environmental hazard. TBNPA half-life is estimated to be about 100 years. This implies that high concentrations of TBNPA will persist in the aquifer long after the elimination of all its sources.

Synthesis metal nanoparticle

DOEpatents

Bunge, Scott D.; Boyle, Timothy J.

2005-08-16

A method for providing an anhydrous route for the synthesis of amine capped coinage-metal (copper, silver, and gold) nanoparticles (NPs) using the coinage-metal mesityl (mesityl=C.sub.6 H.sub.2 (CH.sub.3).sub.3 -2,4,6) derivatives. In this method, a solution of (Cu(C.sub.6 H.sub.2 (CH.sub.3).sub.3).sub.5, (Ag(C.sub.6 H.sub.2 (CH.sub.3).sub.3).sub.4, or (Au(C.sub.6 H.sub.2 (CH.sub.3).sub.3).sub.5 is dissolved in a coordinating solvent, such as a primary, secondary, or tertiary amine; primary, secondary, or tertiary phosphine, or alkyl thiol, to produce a mesityl precursor solution. This solution is subsequently injected into an organic solvent that is heated to a temperature greater than approximately 100.degree. C. After washing with an organic solvent, such as an alcohol (including methanol, ethanol, propanol, and higher molecular-weight alcohols), oxide free coinage NP are prepared that could be extracted with a solvent, such as an aromatic solvent (including, for example, toluene, benzene, and pyridine) or an alkane (including, for example, pentane, hexane, and heptane). Characterization by UV-Vis spectroscopy and transmission electron microscopy showed that the NPs were approximately 9.2.+-.2.3 nm in size for Cu.degree., (no surface oxide present), approximately 8.5.+-.1.1 nm Ag.degree. spheres, and approximately 8-80 nm for Au.degree..

Cool-flame Extinction During N-Alkane Droplet Combustion in Microgravity

NASA Technical Reports Server (NTRS)

Nayagam, Vedha; Dietrich, Daniel L.; Hicks, Michael C.; Williams, Forman A.

2014-01-01

Recent droplet combustion experiments onboard the International Space Station (ISS) have revealed that large n-alkane droplets can continue to burn quasi-steadily following radiative extinction in a low-temperature regime, characterized by negative-temperaturecoefficient (NTC) chemistry. In this study we report experimental observations of n-heptane, n-octane, and n-decane droplets of varying initial sizes burning in oxygen/nitrogen/carbon dioxide and oxygen/helium/nitrogen environments at 1.0, 0.7, and 0.5 atmospheric pressures. The oxygen concentration in these tests varied in the range of 14% to 25% by volume. Large n-alkane droplets exhibited quasi-steady low-temperature burning and extinction following radiative extinction of the visible flame while smaller droplets burned to completion or disruptively extinguished. A vapor-cloud formed in most cases slightly prior to or following the "cool flame" extinction. Results for droplet burning rates in both the hot-flame and cool-flame regimes as well as droplet extinction diameters at the end of each stage are presented. Time histories of radiant emission from the droplet captured using broadband radiometers are also presented. Remarkably the "cool flame" extinction diameters for all the three n-alkanes follow a trend reminiscent of the ignition delay times observed in previous studies. The similarities and differences among the n-alkanes during "cool flame" combustion are discussed using simplified theoretical models of the phenomenon

Droplet Combustion in a Slow Convective Flow

NASA Technical Reports Server (NTRS)

Nayagam, V.; Hicks, M. C.; Ackerman, M.; Haggard, J. B., Jr.; Williams, F. A.

2003-01-01

The influences of slow convective flow on droplet combustion, particularly in the low Reynolds number regime, have received very little attention in the past. Most studies in the literature are semi-empirical in nature and they were motivated by spray combustion applications in the moderate to high Reynolds number regime. None of the limited number of fundamental theoretical studies applicable to low Reynolds numbers have been verified by rigorous experimental data. Moreover, many unsteady phenomena associated with fluid-dynamic unsteadiness, such as impulsive starting or stopping of a burning droplet, or flow acceleration/deceleration effects, have not been investigated despite their importance in practical applications. In this study we investigate the effects of slow convection on droplet burning dynamics both experimentally and theoretically. The experimental portion of the study involves both ground-based experiments in the drop towers and future flight experiments on board the International Space Station. Heptane and methanol are used as test fuels, and this choice complements the quiescent-environment studies of the Droplet Combustion Experiment (DCE). An analytical model that employs the method of matched asymptotic expansions and uses the ratio of the convective velocity far from the droplet to the Stefan velocity at its surface as the small parameter for expansion has also been developed as a part of this investigation. Results from the ground-based experiments and comparison with the analytical model are presented in this report.

A new agent for derivatizing carbonyl species used to investigate limonene ozonolysis

NASA Astrophysics Data System (ADS)

Wells, J. R.; Ham, Jason E.

2014-12-01

A new method for derivatizing carbonyl compounds is presented. The conversion of a series of dicarbonyls to oximes in aqueous solution and from gas-phase sampling was achieved using O-tert-butylhydroxylamine hydrochloride (TBOX). Some advantages of using this derivatization agent include: aqueous reactions, lower molecular weight oximes, and shortened oxime-formation reaction time. Additionally, the TBOX derivatization technique was used to investigate the carbonyl reaction products from limonene ozonolysis. With ozone (O3) as the limiting reagent, four carbonyl compounds were detected: 7-hydroxy-6-oxo-3-(prop-1-en-2-yl)heptanal; 3-Isopropenyl-6-oxoheptanal (IPOH), 3-acetyl-6-oxoheptanal (3A6O) and one carbonyl of unknown structure. Using cyclohexane as a hydroxyl (OHrad) radical scavenger, the relative yields (peak area) of the unknown carbonyl, IPOH, and 3A6O were reduced indicating the influence secondary OH radicals have on limonene ozonolysis products. The relative yield of the hydroxy-dicarbonyl based on the chromatogram was unchanged suggesting it is only made by the limonene + O3 reaction. The detection of 3A6O using TBOX highlights the advantages of a smaller molecular weight derivatization agent for the detection of multi-carbonyl compounds. The use of TBOX derivatization if combined with other derivatization agents may address a recurring need to simply and accurately detect multi-functional oxygenated species in air.

Effect of Fresh Garlic on Lipid Oxidation and Microbiological Changes of Pork Patties during Refrigerated Storage

PubMed Central

2014-01-01

The effects of two levels (1.4 vs 2.8%) of fresh garlic on lipid oxidation and microbial growth in pork patties were evaluated. Hunter color (L, a, b), pH, thiobarbituric acid reactive substances (TBARS), oxidative volatile compounds, total bacteria and Enterobacteriaceae in the pork patties with or without fresh garlic were measured during storage at 4℃. Addition of fresh garlic decreased redness (a), while increased pH and yellowness (b) values of the fresh pork patties were observed, regardless of the levels added. The TBARS values of the pork patties were increased with the addition of fresh garlic (p<0.05). Similar results were observed in oxidative volatile compounds. A total of 13 volatile compounds were detected in the patties (5 sulfur-containing compounds, including allyl mercaptan, allyl methyl sulfide, diallyl sulfide, methyl-(E)-propenyl-disulfide, and diallyl disulfide, and the 8 other oxidative compounds, including 1-pentanol, hexanal, 1-hexanol, heptanal, (E)-2-heptenal, 1-octen-3-ol, (E)-2-octenal and nonanal). Fresh garlic accelerated development of oxidative products in the pork patties, especially hexanal and the total oxidative volatile compounds. However, the addition of 1.4 and 2.8% of fresh garlic inhibited the growth of total bacteria and Enterobacteriaceae, indicating low total bacterial counts and Enterobacteriaceae than the controls. PMID:26761498

Relationship between sensory attributes and volatile compounds of polish dry-cured loin

PubMed Central

Górska, Ewa; Nowicka, Katarzyna; Jaworska, Danuta; Przybylski, Wiesław; Tambor, Krzysztof

2017-01-01

Objective The aim of this work was to determine the relationship between objective sensory descriptors and volatile flavour compound composition of Polish traditional dry-cured loin. Methods The volatile compounds were investigated by using solid phase microextraction (SPME) and gas chromatography–mass spectrometry (GC–MS). For sensory assessment, the quantitative descriptive analysis (QDA) method was used. Results A total of 50 volatile compounds were found and assigned to 17 chemical families. Most of the detected volatile compounds derived from smoking, lipid oxidative reactions and seasoning (46.8%, 21.7%, and 18.9%, respectively). The dominant compounds were: aromatic hydrocarbon (toluene); alkanes (hexane, heptane, and 2,2,4-trimethylpentane); aldehyde (hexanal); alcohol (2-furanmethanol); ketone (3-hydroxy-2-butanone); phenol (guaiacol); and terpenes (eucalyptol, cymene, γ-terpinen, and limonene). Correlation analysis showed that some compounds derived from smoking were positively correlated with the intensity of cured meat odour and flavour and negatively with the intensity of dried meat odour and flavour, while terpenes were strongly correlated with odour and flavour of added spices. Conclusion The analysed dry-cured loins were characterized by specific and unique sensory profile. Odour and flavour of studied loins was mainly determined by volatile compounds originating from smoking, seasoning and lipid oxidation. Obtained results suggest that smoking process is a crucial stage during Polish traditional dry-cured loins production. PMID:27456422

Crystal structure of rac-(3aR,4S,5aR,6S,9R,10aS,10bR)-3a,5a,9-tri­methyl­tetra­deca­hydro-6,9-ep­oxy­cyclo­hepta­[e]inden-4-ol monohydrate

PubMed Central

Schäfer, Andreas; Golz, Christopher; Preut, Hans; Strohmann, Carsten; Hiersemann, Martin

2015-01-01

The title hydrate, C17H28O2·H2O, was synthesized in order to determine the relative configuration of the tetra­cyclic framework. The fused 5,6,7-tricarbocyclic core exhibits an entire cis-annulation, featuring a 1,4-cis-relation of the angular methyl groups in the six-membered ring. The oxa bridge of the ep­oxy­cyclo­heptane moiety is oriented towards the concave face of the boat-shaped mol­ecule, whereas the angular methyl groups are directed towards the convex face. The asymmetric unit of the crystal contains two nearly identical formula units, which are related via a pseudo-centre of symmetry. The structure could be solved in the space groups I-4 and I41/a. The refinement in the acentric space group, however, gave significantly better results and these are used in this paper. O—H⋯O hydrogen bonds are observed between the organic mol­ecules, between the organic mol­ecules and the water mol­ecules, and between the water mol­ecules, forming a chain along the c-axis direction. PMID:26396907

Ziegler-Natta Catalyst Based on MgCl₂/Clay/ID/TiCl₄ for the Synthesis of Spherical Particles of Polypropylene Nanocomposites.

PubMed

Cardoso, Renata da Silva; Oliveira, Jaqueline da Silva; Ramis, Luciana Bortolin; Marques, Maria de Fátima V

2018-07-01

In the present work, we have designed MgCl2/clay/internal donor (ID)/TiCl4 based bisupported Ziegler-Natta catalysts containing varying amounts of organoclay (montmorillonite) in order to synthesize spherical particles of polypropylene/clay nanocomposites (PCN). The organoclay was introduced into the catalyst support formulation and PCN was obtained using the in situ polymerization technique. Decreasing the reaction time, it was possible to obtain nanocomposites with high concentrations of clay (masterbatches). Micrographs of SEM confirmed the spherical morphology of the catalysts. In addition, XRD patterns show that the active sites for polymerization were inserted in the clay galleries. The catalytic performance was evaluated in slurry propylene polymerization using triethylaluminium as cocatalyst and silane as external electron donor at 70 °C, 4 bar, and different reaction times. The PCNs obtained containing different clay amounts were characterized by X-ray diffraction, thermal analyses, transmission electronic microscopy, and extractables in heptane. The results revealed that the synthesized PP/clay particles were also spherical showing that the morphological control is possible even using catalysts containing high amounts of clay. The PCN presented high degradation temperature (459 °C). The XRD peak related to the clay interlamellar distance has shifted to lower angles, and TEM images confirmed the formation of exfoliated/intercalated clay on the PP matrix and absence of microparticles of clay.

Droplet Suspended on a Wire Begins Ignition

NASA Technical Reports Server (NTRS)

2003-01-01

The Fiber Supported Droplet Combustion Experiment completing a number of successful burns on STS-94, July 11, 1997, MET:9/17:40 (approximate). The photo shows a droplet of 95% heptane and 5% hexadecane, suspended and positioned by the fiber wire, just as it is being ignited by the glowing coil beneath. Study of the physical properties of burning fuel from this experiment is expected to contribute to more efficient use of fossil fuels and reduction of combustion by-products on Earth. The sequence is from a time-lapse movie (34 seconds condensed to 12 seconds), and clearly shows particles emanating from the droplet during the burn. The droplet shrank to nothing as it was consumed. FSDC-2 studied fundamental phenomena related to liquid fuel droplet combustion in air. Pure fuels and mixtures of fuels were burned as isolated single and dual droplets with and without forced air convection. The FSDC guest investigator was Forman Williams, University of California, San Diego. The experiment was part of the space research investigations conducted during the Microgravity Science Laboratory-1R mission (STS-94, July 1-17 1997). Advanced combustion experiments will be a part of investigations plarned for the International Space Station. (1.2 MB, 11-second MPEG, screen 320 x 240 pixels; downlinked video, higher quality not available) A still JPG composite of this movie is available at http://mix.msfc.nasa.gov/ABSTRACTS/MSFC-0300180.html.

Ignition of Droplet Suspended on a Wire

NASA Technical Reports Server (NTRS)

2003-01-01

The Fiber Supported Droplet Combustion Experiment completing a number of successful burns on STS-94, July 11, 1997, MET:9/17:40 (approximate). The photo shows a droplet of 95% heptane and 5% hexadecane, suspended and positioned by the fiber wire, just as it is being ignited by the glowing coil beneath. Study of the physical properties of burning fuel from this experiment is expected to contribute to more efficient use of fossil fuels and reduction of combustion by-products on Earth. The sequence is from a time-lapse movie (34 seconds condensed to 12 seconds), and clearly shows particles emanating from the droplet during the burn. The droplet shrank to nothing as it was consumed. FSDC-2 studied fundamental phenomena related to liquid fuel droplet combustion in air. Pure fuels and mixtures of fuels were burned as isolated single and dual droplets with and without forced air convection. The FSDC guest investigator was Forman Williams, University of California, San Diego. The experiment was part of the space research investigations conducted during the Microgravity Science Laboratory-1R mission (STS-94, July 1-17 1997). Advanced combustion experiments will be a part of investigations plarned for the International Space Station. (133KB JPEG, 656 x 741 pixels; downlinked video, higher quality not available) The MPG from which this composite was made is available at http://mix.msfc.nasa.gov/ABSTRACTS/MSFC-0300181.html.

Interfacing supercritical fluid reaction apparatus with on-line liquid chromatography: monitoring the progress of a synthetic organic reaction performed in supercritical fluid solution.

PubMed

Ramsey, Edward D; Li, Ben; Guo, Wei; Liu, Jing Y

2015-04-03

An interface has been developed that connects a supercritical fluid reaction (SFR) vessel directly on-line to a liquid chromatograph. The combined SFR-LC system has enabled the progress of the esterification reaction between phenol and benzoyl chloride to synthesize phenyl benzoate in supercritical fluid carbon dioxide solution to be dynamically monitored. This was achieved by the periodic SFR-LC analysis of samples directly withdrawn from the esterification reaction mixture. Using the series of SFR-LC analysis results obtained for individual esterification reactions, the reaction progress profile for each esterification reaction was obtained by expressing the measured yield of phenyl benzoate as a function of reaction time. With reaction temperature fixed at 75°C, four sets (n=3) of SFR-LC reaction progress profiles were obtained at four different SFR pressures ranging from 13.79 to 27.58 MPa. The maximum SFR yield obtained for phenyl benzoate using a standard set of reactant concentrations was 85.2% (R.S.D. 4.2%) when the reaction was performed at 13.79 MPa for 90 min. In comparison, a phenyl benzoate yield of less than 0.3% was obtained using the same standard reactant concentrations after 90 min reaction time at 75°C using either: heptane, ethyl acetate or acetonitrile as conventional organic reaction solvents. Copyright © 2015 Elsevier B.V. All rights reserved.

Validation of lipolysis product extraction from aqueous/biological samples, separation and quantification by thin-layer chromatography with flame ionization detection analysis using O-cholesteryl ethylene glycol as a new internal standard.

PubMed

Cavalier, Jean-François; Lafont, Dominique; Boullanger, Paul; Houisse, David; Giallo, Jacqueline; Ballester, Jean-Michel; Carrière, Frédéric

2009-09-11

A general and easily accessible method for the extraction followed by the simultaneous separation and quantitative determination of triacylglycerols, diacylglycerols, monoacylglycerols and free fatty acids has been improved and optimized based on existing protocols using liquid-phase extraction and thin-layer chromatography coupled to flame ionization detection (TLC/FID Iatroscan). After lipid extraction in the presence of a suitable new synthetic internal standard, namely CholE1, a single elution step using n-heptane/diethyl ether/formic acid (55:45:1, v/v/v) was applied. This method was validated in line with international bioanalytical method validation guidelines using two different matrix systems: purified water and human gastro-intestinal fluid. Overall, the assay was found to have high levels of precision with coefficients of variation ranging from 1.48% to 11.0% and accuracy ranging from -13.3% to +5.79% RE. The confidence limits of the lipid mean recovery rates varied between 89.9% and 104%. This method is therefore highly suitable for quantifying the lipolysis products generated in vitro during the hydrolysis of various fats and oils by digestive lipases, as well as those collected from the gastro-intestinal tract in the course of human clinical studies on lipid digestion.

Chemical Action of Halogenated Agents in Fire Extinguishing

NASA Technical Reports Server (NTRS)

Belles, Frank E.

1955-01-01

The action of halogenated agents in preventing flame propagation in fuel-air mixtures in laboratory tests is discussed in terms of a possible chemical mechanism. The mechanism chosen is that of chain-breaking reactions between agent and active particles (hydrogen and oxygen atoms and hydroxyl radicsls). Data from the literature on the flammability peaks of n-heptane agent-air mixtures are treated. Ratings of agent effectiveness in terms of the fuel equivalent of the agent, based on both fuel and agent concentrations at the peak, are proposed as preferable to ratings in terms of agent concentration alone. These fuel-equivalent ratings are roughly correlated by reactivities assigned to halogen and hydrogen atoms in the agent molecules. It is concluded that the presence of hydrogen in agent need not reduce its fire-fighting ability, provided there is enough halogen to make the agent nonflammable. A method is presented for estimating from quenching-distance data a rate constant for the reaction of agent with active particles. A quantitative result is obtained for methyl bromide. This rate constant predicts the observed peak concentration of methyl bromide quite well. However, more data are needed to prove the validity of the method. The assumption that hal.ogenatedagents act mainly by chain-bresking reactions with active particles is consistent with the experimental facts and should help guide the selection of agents for further tests.

Analysis of volatile organic compounds in pleural effusions by headspace solid-phase microextraction coupled with cryotrap gas chromatography and mass spectrometry.

PubMed

Huang, Zhongping; Zhang, Jie; Zhang, Peipei; Wang, Hong; Pan, Zaifa; Wang, Lili

2016-07-01

Headspace solid-phase microextraction coupled with cryotrap gas chromatography and mass spectrometry was applied to the analysis of volatile organic compounds in pleural effusions. The highly volatile organic compounds were separated successfully with high sensitivity by the employment of a cryotrap device, with the construction of a cold column head by freezing a segment of metal capillary with liquid nitrogen. A total of 76 volatile organic compounds were identified in 50 pleural effusion samples (20 malignant effusions and 30 benign effusions). Among them, 34 more volatile organic compounds were detected with the retention time less than 8 min, by comparing with the normal headspace solid-phase microextraction coupled with gas chromatography and mass spectrometry method. Furthermore, 24 volatile organic compounds with high occurrence frequency in pleural effusion samples, 18 of which with the retention time less than 8 min, were selected for the comparative analysis. The results of average peak area comparison and box-plot analysis showed that except for cyclohexanone, 2-ethyl-1-hexanol, and tetramethylbenzene, which have been reported as potential cancer biomarkers, cyclohexanol, dichloromethane, ethyl acetate, n-heptane, ethylbenzene, and xylene also had differential expression between malignant and benign effusions. Therefore, the proposed approach was valuable for the comprehensive characterization of volatile organic compounds in pleural effusions. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Extended lattice Boltzmann scheme for droplet combustion.

PubMed

Ashna, Mostafa; Rahimian, Mohammad Hassan; Fakhari, Abbas

2017-05-01

The available lattice Boltzmann (LB) models for combustion or phase change are focused on either single-phase flow combustion or two-phase flow with evaporation assuming a constant density for both liquid and gas phases. To pave the way towards simulation of spray combustion, we propose a two-phase LB method for modeling combustion of liquid fuel droplets. We develop an LB scheme to model phase change and combustion by taking into account the density variation in the gas phase and accounting for the chemical reaction based on the Cahn-Hilliard free-energy approach. Evaporation of liquid fuel is modeled by adding a source term, which is due to the divergence of the velocity field being nontrivial, in the continuity equation. The low-Mach-number approximation in the governing Navier-Stokes and energy equations is used to incorporate source terms due to heat release from chemical reactions, density variation, and nonluminous radiative heat loss. Additionally, the conservation equation for chemical species is formulated by including a source term due to chemical reaction. To validate the model, we consider the combustion of n-heptane and n-butanol droplets in stagnant air using overall single-step reactions. The diameter history and flame standoff ratio obtained from the proposed LB method are found to be in good agreement with available numerical and experimental data. The present LB scheme is believed to be a promising approach for modeling spray combustion.

High-speed combustion diagnostics in a rapid compression machine by broadband supercontinuum absorption spectroscopy.

PubMed

Werblinski, Thomas; Fendt, Peter; Zigan, Lars; Will, Stefan

2017-05-20

The first results under fired internal combustion engine conditions based on a supercontinuum absorption spectrometer are presented and discussed. Temperature, pressure, and water mole fraction are inferred simultaneously from broadband H 2 O absorbance spectra ranging from 1340 nm to 1440 nm. The auto-ignition combustion process is monitored for two premixed n-heptane/air mixtures with 10 kHz in a rapid compression machine. Pressure and temperature levels during combustion exceed 65 bar and 1900 K, respectively. To allow for combustion measurements, the robustness of the spectrometer against beam steering has been improved compared to its previous version. Additionally, the detectable wavelength range has been extended further into the infrared region to allow for the acquisition of distinct high-temperature water transitions located in the P-branch above 1410 nm. Based on a theoretical study, line-of-sight (LOS) effects introduced by temperature stratification on the broadband fitting algorithm in the complete range from 1340 nm to 1440 nm are discussed. In this context, the recorded spectra during combustion were evaluated only within a narrower spectral region exhibiting almost no interference from low-temperature molecules (here, P-branch from 1410 nm to 1440 nm). It is shown that this strategy mitigates almost all of the LOS effects introduced by cold molecules and the evaluation of the spectrum in the entirely recorded wavelength range at engine combustion conditions.

Temperature measurements of the gas-phase during surrogate diesel injection using two-color toluene LIF

NASA Astrophysics Data System (ADS)

Zegers, R. P. C.; Yu, M.; Bekdemir, C.; Dam, N. J.; Luijten, C. C. M.; de Goey, L. P. H.

2013-08-01

Planar laser-induced fluorescence (LIF) of toluene has been applied in an optical engine and a high-pressure cell, to determine temperatures of fuel sprays and in-cylinder vapors. The method relies on a redshift of the toluene LIF emission spectrum with increasing temperature. Toluene fluorescence is recorded simultaneously in two disjunct wavelength bands by a two-camera setup. After calibration, the pixel-by-pixel LIF signal ratio is a proxy for the local temperature. A detailed measurement procedure is presented to minimize measurement inaccuracies and to improve precision. n-Heptane is used as the base fuel and 10 % of toluene is added as a tracer. The toluene LIF method is capable of measuring temperatures up to 700 K; above that the signal becomes too weak. The precision of the spray temperature measurements is 4 % and the spatial resolution 1.3 mm. We pay particular attention to the construction of the calibration curve that is required to translate LIF signal ratios into temperature, and to possible limitations in the portability of this curve between different setups. The engine results are compared to those obtained in a constant-volume high-pressure cell, and the fuel spray results obtained in the high-pressure cell are also compared to LES simulations. We find that the hot ambient gas entrained by the head vortex gives rise to a hot zone on the spray axis.

Long Duration Exposure Facility (LDEF) low temperature Heat Pipe Experiment Package (HEPP) flight results

NASA Technical Reports Server (NTRS)

Mcintosh, Roy; Mccreight, Craig; Brennan, Patrick J.

1993-01-01

The Low Temperature Heat Pipe Flight Experiment (HEPP) is a fairly complicated thermal control experiment that was designed to evaluate the performance of two different low temperature ethane heat pipes and a low-temperature (182 K) phase change material. A total of 390 days of continuous operation with an axially grooved aluminum fixed conductance heat pipe and an axially grooved stainless steel heat pipe diode was demonstrated before the data acquisition system's batteries lost power. Each heat pipe had approximately 1 watt applied throughout this period. The HEPP was not able to cool below 188.6 K during the mission. As a result, the preprogrammed transport test sequence which initiates when the PCM temperature drops below 180 K was never exercised, and transport tests with both pipes and the diode reverse mode test could not be run in flight. Also, because the melt temperature of the n-heptane PCM is 182 K, its freeze/thaw behavior could not be tested. Post-flight thermal vacuum tests and thermal analyses have indicated that there was an apparent error in the original thermal analyses that led to this unfortunate result. Post-flight tests have demonstrated that the performance of both heat pipes and the PCM has not changed since being fabricated more than 14 years ago. A summary of HEPP's flight data and post-flight test results are presented.

(+)-Cannabidiol analogues which bind cannabinoid receptors but exert peripheral activity only.

PubMed

Fride, Ester; Feigin, Cfir; Ponde, Datta E; Breuer, Aviva; Hanus, Lumír; Arshavsky, Nina; Mechoulam, Raphael

2004-12-15

Delta9-Tetrahydrocannabinol (Delta9-THC) and (-)-cannabidiol are major constituents of the Cannabis sativa plant with different pharmacological profiles: (-)-Delta9-tetrahydrocannabinol, but not (-)-cannabidiol, activates cannabinoid CB1 and CB2 receptors and induces psychoactive and peripheral effects. We have tested a series of (+)-cannabidiol derivatives, namely, (+)-cannabidiol-DMH (DMH-1,1-dimethylheptyl-), (+)-7-OH-cannabidiol-DMH, (+)-7-OH- cannabidiol, (+)-7-COOH- cannabidiol and (+)-7-COOH-cannabidiol-DMH, for central and peripheral (intestinal, antiinflammatory and peripheral pain) effects in mice. Although all (+)-cannabidiols bind to cannabinoid CB1 and CB2 receptors, only (+)-7-OH-cannabidiol-DMH was centrally active, while all (+)-cannabidiol analogues completely arrested defecation. The effects of (+)-cannabidiol-DMH and (+)-7-OH-cannabidiol-DMH were partially antagonized by the cannabinoid CB1 receptor antagonist N-(piperidiny-1-yl)-5-(4-chlorophenyl)-1-(2,4-dichlorophenyl)-4-methyl-1H-pyrazole-3-carboxamide (SR141716), but not by the cannabinoid CB2 receptor antagonist N-[-(1S)-endo-1,3,3-trimethil bicyclo [2.2.1] heptan-2-yl-5-(4-chloro-3-methylphenyl)-1-(4-methylbenzyl)-pyrazole-3-carboxamide (SR144528), and had no effect on CB1(-/-) receptor knockout mice. (+)-Cannabidiol-DMH inhibited the peripheral pain response and arachidonic-acid-induced inflammation of the ear. We conclude that centrally inactive (+)-cannabidiol analogues should be further developed as antidiarrheal, antiinflammatory and analgesic drugs for gastrointestinal and other peripheral conditions.

Methane and other hydrocarbon gases in sediment from the southeastern North American continental margin

USGS Publications Warehouse

Kvenvolden, K.A.; Lorenson, T.D.

2000-01-01

Residual concentrations and distributions of hydrocarbon gases from methane to n-heptane were measured in sediments at seven sites on Ocean Drilling Program (ODP) Leg 164. Three sites were drilled at the Cape Fear Diapir of the Carolina Rise, and one site was drilled on the Blake Ridge Diapir. Methane concentrations at these sites result from microbial generation which is influenced by the amount of pore-water sulfate and possible methane oxidation. Methane hydrate was found at the Blake Ridge Diapir site. The other hydrocarbon gases at these sites are likely the produce of early microbial processes. Three sites were drilled on a transect of holes across the crest of the Blake Ridge. The base of the zone of gas-hydrate occurrence was penetrated at all three sites. Trends in hydrocarbon gas distributions suggest that methane is microbial in origin and that the hydrocarbon gas mixture is affected by diagenesis, outgassing, and, near the surface, by microbial oxidation. Methane hydrate was recovered at two of these three sites, although gas hydrate is likely present at all three sites. The method used here for determining amounts of residual hydrocarbon gases has its limitations and provides poor assessment of gas distributions, particularly in the stratigraphic interval below about ~ 100 mbsf. One advantage of the method, however, is that it yields sufficient quantities of gas for other studies such as isotopic determinations.

Real-Gas Effects on Binary Mixing Layers

NASA Technical Reports Server (NTRS)

Okong'o, Nora; Bellan, Josette

2003-01-01

This paper presents a computational study of real-gas effects on the mean flow and temporal stability of heptane/nitrogen and oxygen/hydrogen mixing layers at supercritical pressures. These layers consist of two counterflowing free streams of different composition, temperature, and density. As in related prior studies reported in NASA Tech Briefs, the governing conservation equations were the Navier-Stokes equations of compressible flow plus equations for the conservation of total energy and of chemical- species masses. In these equations, the expressions for heat fluxes and chemical-species mass fluxes were derived from fluctuation-dissipation theory and incorporate Soret and Dufour effects. Similarity equations for the streamwise velocity, temperature, and mass fractions were derived as approximations to the governing equations. Similarity profiles showed important real-gas, non-ideal-mixture effects, particularly for temperature, in departing from the error-function profile, which is the similarity solution for incompressible flow. The temperature behavior was attributed to real-gas thermodynamics and variations in Schmidt and Prandtl numbers. Temporal linear inviscid stability analyses were performed using the similarity and error-function profiles as the mean flow. For the similarity profiles, the growth rates were found to be larger and the wavelengths of highest instability shorter, relative to those of the errorfunction profiles and to those obtained from incompressible-flow stability analysis. The range of unstable wavelengths was found to be larger for the similarity profiles than for the error-function profiles