Exposures to 1,6-hexamethylene diisocyanate during polyurethane spray painting in the U.S. Air Force.

PubMed

Carlton, G N; England, E C

2000-09-01

1,6-Hexamethylene diisocyanate (HDI) exposures were measured during polyurethane enamel spray painting at four Air Force bases. Breathing zone samples were collected for HDI monomer and polyisocyanates (oligomers) using three sampling methods: NIOSH Method 5521, the Iso-Chek sampler, and the total aerosol mass method (TAMM). Exposures to HDI monomer are low when compared to current occupational exposure limits; the highest 8-hr time-weighted average (TWA) exposure found was 3.5 micrograms/m3, below the American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 34 micrograms/m3. HDI oligomer levels were higher; mean task exposures indicated by either the Iso-Chek sampler or TAMM are above the Oregon ceiling limit of 1 mg/m3. Eight-hour TWA exposures, however, were much lower, with only one exceeding the Oregon standard of 0.5 mg/m3. Poor worker practices commonly observed during this study included: standing in downwind positions so paint overspray passed through breathing zones; spraying toward other painters; and using excessive paint spray gun air cap pressures. Workers should stand in upwind orientation relative to the aircraft being painted, causing overspray to move away from the painter's breathing zone; adjust their position to prevent spraying other painters or limit paint application to one worker at a time; and use air cap pressure gauges prior to spraying to limit spray gun air cap pressures and reduce paint overspray generation rates. These improved techniques will result in reduced worker exposures to isocyanates.

Morphology and surface properties of high strength siloxane poly(urethane-urea)s developed for heart valve application.

PubMed

Dandeniyage, Loshini S; Adhikari, Raju; Bown, Mark; Shanks, Robert; Adhikari, Benu; Easton, Christopher D; Gengenbach, Thomas R; Cookson, David; Gunatillake, Pathiraja A

2018-03-04

A series of siloxane poly(urethane-urea) (SiPUU) were developed by incorporating a macrodiol linked with a diisocyanate to enhance mixing of hard and soft segments (SS). The effect of this modification on morphology, surface properties, surface elemental composition, and creep resistance was investigated. The linked macrodiol was prepared by reacting α,ω-bis(6-hydroxyethoxypropyl) poly(dimethylsiloxane)(PDMS) or poly(hexamethylene oxide) (PHMO) with either 4,4'-methylenediphenyl diisocyanate (MDI), hexamethylene diisocyanate (HDI), or isophorone diisocyanate (IPDI). SiPUU with PHMO-MDI-PHMO and PHMO-IPDI-PHMO linked macrodiols showed enhanced creep resistance and recovery when compared with a commercial biostable polyurethane, Elast-Eon™ 2A. Small and wide-angle X-ray scattering data were consistent with significant increase of hydrogen bonding between hard and SS with linked-macrodiols, which improved SiPUU's tensile stress and tear strengths. These SiPUU were hydrophobic with contact angle higher than 101° and they had low water uptake (0.7%·w/w of dry mass). They also had much higher siloxane concentration on the surface compared to that in the bulk. © 2018 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2018. © 2018 Wiley Periodicals, Inc.

Diisocyanate-exposed auto body shop workers: a one-year follow-up.

PubMed

Redlich, C A; Stowe, M H; Coren, B A; Wisnewski, A V; Holm, C T; Cullen, M R

2002-12-01

Diisocyanates currently are the most commonly identified cause of occupational asthma in industrialized countries. Auto body shops, a common hexamethylene diisocyanate (HDI) exposure setting, are difficult to study due to their small size and episodic exposures. A 1-year follow-up was undertaken as an adjunct to the cross-sectional SPRAY study (Survey of Painters & Repairers of Auto bodies by Yale) to investigate the effects of HDI on auto body shop workers over time and whether or not the healthy worker effect may exist in this industry. Forty-eight workers from seven shops were re-contacted. Thirty-four subjects who stayed at the same shop and 11 who left their original shop participated. No statistically significant changes in physiology, symptoms, and immunologic responses from baseline to follow-up were noted. However, significant differences between those who left the shops and those who stayed were noted. Those who left were younger, less experienced in the industry, and more likely to have a history of asthma (23 vs. 3%; P < 0.05), bronchial hyper-responsiveness (23 vs. 9%), HDI-specific IgG (64 vs. 29%; P < 0.05), and HDI-specific proliferation (S.I. 2.0 vs. 1.3; P < 0.05). The differences in workers who stayed at their shop compared to those who left, combined with the low asthma prevalence and high job turnover rate, all suggest that a healthy worker effect may exist in the auto body industry, and may in part account for the low prevalence of asthma noted in SPRAY and other cross-sectional studies of diisocyante workers. Copyright 2002 Wiley-Liss, Inc.

Temperature- and pH-responsive nanoparticles of biocompatible polyurethanes for doxorubicin delivery.

PubMed

Wang, Anning; Gao, Hui; Sun, Yanfang; Sun, Yu-long; Yang, Ying-Wei; Wu, Guolin; Wang, Yinong; Fan, Yunge; Ma, Jianbiao

2013-01-30

A series of temperature- and pH-responsive polyurethanes based on hexamethylene diisocyanate (HDI) and 4,4'-diphenylmethane diisocyanate (MDI) were synthesized by a coupling reaction with bis-1,4-(hydroxyethyl) piperazine (HEP), N-methyldiethanolamine (MDEA) and N-butyldiethanolamine (BDEA), respectively. The chemical structure, molecular weight, thermal property and crystallization properties were characterized by Fourier transform infrared (FT-IR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC) and X-ray diffraction (XRD) spectroscopy. The resulting polyurethanes were then used to prepare nanoparticles either by direct dispersion method or dialysis method. Their pH and temperature responsibilities were evaluated by optical transmittance and size measurement in aqueous media. Interestingly, HDI-based and MDI-based polyurethanes exhibited different pH and temperature responsive properties. Nanoparticles based on HDI-HEP and HDI-MDEA were temperature-responsive, while MDI-based biomaterials were not. All of them showed pH-sensitive behavior. The possible responsive mechanism was investigated by (1)H NMR spectroscopy. The cytotoxicity of the polyurethanes was evaluated using methylthiazoletetrazolium (MTT) assay in vitro. It was shown that the HDI-based polyurethanes were non-toxic, and could be applied to doxorubicin (DOX) encapsulation. The experimental results indicated that DOX could be efficiently encapsulated into polyurethane nanoparticles and uptaken by Huh-7 cells. The loaded DOX molecules could be released from the drug-loaded polyurethane nanoparticles upon pH and temperature changes, responsively. Copyright © 2012 Elsevier B.V. All rights reserved.

Development of high strength siloxane poly(urethane-urea) elastomers based on linked macrodiols for heart valve application.

PubMed

Dandeniyage, Loshini S; Gunatillake, Pathiraja A; Adhikari, Raju; Bown, Mark; Shanks, Robert; Adhikari, Benu

2017-08-31

Mixed macrodiol based siloxane poly(urethane-urea)s (SiPUU) having number average molecular weights in the range 87-129 kDa/mol were synthesized to give elastomers with high tensile and tear strengths required to fabricate artificial heart valves. Polar functional groups were introduced into the soft segment to improve the poor segmental compatibility of siloxane polyurethanes. This was achieved by linking α,ω-bis(6-hydroxyethoxypropyl) poly(dimethylsiloxane) (PDMS) or poly(hexamethylene oxide) (PHMO) macrodiols with either 4,4'-methylenediphenyl diisocyanate (MDI), hexamethylene diisocyanate (HDI) or isophorone diisocyanate (IPDI) prior to polyurethane synthesis. The hard segment was composed of MDI, and a 1:1 mixture of 1,3-bis(4-hydroxybutyl)-1,1,3,3-tetramethyldisiloxane and 1,2-ethylene diamine. We report the effect of urethane linkers in soft segments on properties of the SiPUU. PHMO linked with either MDI or IPDI produced SiPUU with the highest tensile and tear strengths. Linking PDMS hardly affected the tensile strength; however, the tear strength was improved. The stress-strain curves showed no plastic deformation region typically observed for conventional polyurethanes indicating good creep resistance. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2017. © 2017 Wiley Periodicals, Inc.

Isocyanate Exposure Below Analytical Detection When a Paint Brush and Roller Are Used to Apply Moisture-Cure Polyurethane Paint.

PubMed

Reeb-Whitaker, Carolyn K; Schoonover, Todd M

2016-05-01

Isocyanate exposure is known to be hazardous when polyurethane paints are applied with a spray gun, but less is known of exposure when paint is applied with a paint brush and roller. Concentrations of 1,6-hexamethylene diisocyanate (HDI) monomer and three HDI polymers were assessed when two moisture-cure polyurethane paints containing 31-35% isocyanates were applied with a paint roller and brush. Short-term 15-min samples were taken during paint application in an indoor test environment with no ventilation (n= 12); in an outdoor test environment (n= 11); and in an outdoor in-situ assessment (n= 22). The outdoor in-situ assessment involved the painting of a bus shelter and light poles at a public transit station over two night shifts. All isocyanate samples were below analytical detection. The analytical limits of detection for HDI monomer, HDI biuret, HDI isocyanurate, and HDI uretdione were 0.005, 0.84, 0.87, and 0.88 µg, respectively. The finding that isocyanate concentrations were below detection is attributed to the use of paint roller and brush which minimize paint aerosolization and the paint formulation itself which contained <1% of volatile HDI monomer. © The Author 2016. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Airborne isocyanate exposures in the collision repair industry and a comparison to occupational exposure limits.

PubMed

Reeb-Whitaker, Carolyn; Whittaker, Stephen G; Ceballos, Diana M; Weiland, Elisa C; Flack, Sheila L; Fent, Kenneth W; Thomasen, Jennifer M; Trelles Gaines, Linda G; Nylander-French, Leena A

2012-01-01

Isocyanate exposure was evaluated in 33 spray painters from 25 Washington State autobody shops. Personal breathing zone samples (n = 228) were analyzed for isophorone diisocyanate (IPDI) monomer, 1,6-hexamethylene diisocyanate (HDI) monomer, IPDI polyisocyanate, and three polyisocyanate forms of HDI. The objective was to describe exposures to isocyanates while spray painting, compare them with short-term exposure limits (STELs), and describe the isocyanate composition in the samples. The composition of polyisocyanates (IPDI and HDI) in the samples varied greatly, with maximum amounts ranging from up to 58% for HDI biuret to 96% for HDI isocyanurate. There was a significant inverse relationship between the percentage composition of HDI isocyanurate to IPDI and to HDI uretdione. Two 15-min STELs were compared: (1) Oregon's Occupational Safety and Health Administration (OR-OSHA) STEL of 1000 μg/m(3) for HDI polyisocyanate, and (2) the United Kingdom's Health and Safety Executive (UK-HSE) STEL of 70 μg NCO/m(3) for all isocyanates. Eighty percent of samples containing HDI polyisocyanate exceeded the OR-OSHA STEL while 98% of samples exceeded the UK-HSE STEL. The majority of painters (67%) wore half-face air-purifying respirators while spray painting. Using the OR-OSHA and the UK-HSE STELs as benchmarks, 21% and 67% of painters, respectively, had at least one exposure that exceeded the respirator's OSHA-assigned protection factor. A critical review of the STELs revealed the following limitations: (1) the OR-OSHA STEL does not include all polyisocyanates, and (2) the UK-HSE STEL is derived from monomeric isocyanates, whereas the species present in typical spray coatings are polyisocyanates. In conclusion, the variable mixtures of isocyanates used by autobody painters suggest that an occupational exposure limit is required that includes all polyisocyanates. Despite the limitations of the STELs, we determined that a respirator with an assigned protection factor of 25 or greater is required to protect against isocyanate exposures during spray painting. Consequently, half-face air-purifying respirators, which are most commonly used and have an assigned protection factor of 10, do not afford adequate respiratory protection.

Airborne Isocyanate Exposures in the Collision Repair Industry and a Comparison to Occupational Exposure Limits

PubMed Central

Reeb-Whitaker, Carolyn; Whittaker, Stephen G.; Ceballos, Diana M.; Weiland, Elisa C.; Flack, Sheila L.; Fent, Kenneth W.; Thomasen, Jennifer M.; Gaines, Linda G. Trelles; Nylander-French, Leena A.

2014-01-01

Isocyanate exposure was evaluated in 33 spray painters from 25 Washington State autobody shops. Personal breathing zone samples (n = 228) were analyzed for isophorone diisocyanate (IPDI) monomer, 1,6-hexamethylene diisocyanate (HDI) monomer, IPDI polyisocyanate, and three polyisocyanate forms of HDI. The objective was to describe exposures to isocyanates while spray painting, compare them with short-term exposure limits (STELs), and describe the isocyanate composition in the samples. The composition of polyisocyanates (IPDI and HDI) in the samples varied greatly, with maximum amounts ranging from up to 58% for HDI biuret to 96% for HDI isocyanurate. There was a significant inverse relationship between the percentage composition of HDI isocyanurate to IPDI and to HDI uretdione. Two 15-min STELs were compared: (1) Oregon's Occupational Safety and Health Administration (OR-OSHA) STEL of 1000 μg/m3 for HDI polyisocyanate, and (2) the United Kingdom's Health and Safety Executive (UK-HSE) STEL of 70 μg NCO/m3 for all isocyanates. Eighty percent of samples containing HDI polyisocyanate exceeded the OR-OSHA STEL while 98% of samples exceeded the UKHSE STEL. The majority of painters (67%) wore half-face air-purifying respirators while spray painting. Using the OROSHA and the UK-HSE STELs as benchmarks, 21% and 67% of painters, respectively, had at least one exposure that exceeded the respirator's OSHA-assigned protection factor. A critical review of the STELs revealed the following limitations: (1) the OR-OSHA STEL does not include all polyisocyanates, and (2) the UK-HSE STEL is derived from monomeric isocyanates, whereas the species present in typical spray coatings are polyisocyanates. In conclusion, the variable mixtures of isocyanates used by autobody painters suggest that an occupational exposure limit is required that includes all polyisocyanates. Despite the limitations of the STELs, we determined that a respirator with an assigned protection factor of 25 or greater is required to protect against isocyanate exposures during spray painting. Consequently, half-face air-purifying respirators, which are most commonly used and have an assigned protection factor of 10, do not afford adequate respiratory protection. PMID:22500941

Synthesis and characterization of shape-memory poly carbonate urethane microspheres for future vascular embolization.

PubMed

Liu, Rongrong; Dai, Honglian; Zhou, Qian; Zhang, Qian; Zhang, Ping

2016-08-01

Two types of shape memory poly carbonate urethanes (PCUs) microspheres were synthesized by pre-polymerization and suspension polymerization, based on Polycarbonate diol (PCDL) as the soft segment, Isophorone diisocyanate (IPDI) and 1,6-hexamethylene diisocyanate (HDI) as the hard segments and 1,4-butanediol (BDO) as the chain expanding agent. The structure, crystallinity, and thermal property of the two synthesized PCUs were characterized by Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), Differential scanning calorimetery (DSC), respectively. The results showed that the two types of PCUs exhibited high thermal stability with phase separation and semi-crystallinity. Also, the results of the compression test displayed that the shape fixity and the shape recovery of two PCUs were more than 90% compared to the originals, indicating their similar bio-applicability and shape-memory properties. The tensile strength, elongation at break was enhanced by introducing and increasing content of HDI. The water contact angles of PCUs decreased and their surface tension increased by surface modified with Bovine serum albumin (BSA). Furthermore, the biological study results of two types of PCUs from the platelet adhesion test and the cell proliferation inhibition test indicated they had some biocompatibilites. Hence, the PCU microspheres might represent a smart and shape-memory embolic agent for vascular embolization.

1,6-Hexamethylene diisocyanate

Integrated Risk Information System (IRIS)

1,6 - Hexamethylene diisocyanate ; CASRN 822 - 06 - 0 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Hazard Assessments for

Isocyanate exposure and asthma in the UK vehicle repair industry.

PubMed

Stocks, S J; Jones, K; Piney, M; Agius, R M

2015-12-01

Organic diisocyanates are a common cause of occupational asthma, particularly in motor vehicle repair (MVR) workers. The UK Health & Safety Laboratory provides screening for urinary hexamethylenediamine (UHDA), a biomarker of exposure to 1,6-hexamethylene diisocyanate (HDI). The UK Surveillance of Work-related and Occupational Respiratory Disease scheme (SWORD) has collected reports of occupational asthma since 1996. To compare trends in HDI exposure with trends in the incidence of work-related asthma attributed to isocyanates or paint spraying in MVR workers reported to SWORD. Two-level regression models were used to estimate trends in UHDA levels and work-related asthma in MVR workers reported to SWORD. The direction and magnitude of the trends were compared descriptively. From 2006 to 2014, there was a significant decline in the number of urine samples with detectable levels of UHDA (odds ratio = 0.96; 95% confidence intervals 0.94-0.98) and minimal change in those over the guidance value (1.03; 1.00-1.06). Over the same period, there was a significant decline in all asthma cases attributed to isocyanates or paint spraying reported to SWORD (0.90; 0.86-0.94) and a non-significant decline among MVR workers (0.94; 0.86-1.02). The simultaneous decrease in HDI exposure and incident cases of asthma reported to SWORD is temporally consistent with a reduction in exposure to airborne isocyanate leading to a reduction in asthma. Although this is not direct evidence of a causal relationship between the two trends, it is suggestive. © The Author 2015. Published by Oxford University Press on behalf of the Society of Occupational Medicine.

Isocyanate exposure and asthma in the UK vehicle repair industry

PubMed Central

Jones, K.; Piney, M.; Agius, R. M.

2015-01-01

Background Organic diisocyanates are a common cause of occupational asthma, particularly in motor vehicle repair (MVR) workers. The UK Health & Safety Laboratory provides screening for urinary hexamethylenediamine (UHDA), a biomarker of exposure to 1,6-hexamethylene diisocyanate (HDI). The UK Surveillance of Work-related and Occupational Respiratory Disease scheme (SWORD) has collected reports of occupational asthma since 1996. Aims To compare trends in HDI exposure with trends in the incidence of work-related asthma attributed to isocyanates or paint spraying in MVR workers reported to SWORD. Methods Two-level regression models were used to estimate trends in UHDA levels and work-related asthma in MVR workers reported to SWORD. The direction and magnitude of the trends were compared descriptively. Results From 2006 to 2014, there was a significant decline in the number of urine samples with detectable levels of UHDA (odds ratio = 0.96; 95% confidence intervals 0.94–0.98) and minimal change in those over the guidance value (1.03; 1.00–1.06). Over the same period, there was a significant decline in all asthma cases attributed to isocyanates or paint spraying reported to SWORD (0.90; 0.86–0.94) and a non-significant decline among MVR workers (0.94; 0.86–1.02). Conclusions The simultaneous decrease in HDI exposure and incident cases of asthma reported to SWORD is temporally consistent with a reduction in exposure to airborne isocyanate leading to a reduction in asthma. Although this is not direct evidence of a causal relationship between the two trends, it is suggestive. PMID:26209793

An FTIR investigation of isocyanate skin absorption using in vitro guinea pig skin.

PubMed

Bello, Dhimiter; Smith, Thomas J; Woskie, Susan R; Streicher, Robert P; Boeniger, Mark F; Redlich, Carrie A; Liu, Youcheng

2006-05-01

Isocyanates may cause contact dermatitis, sensitization and asthma. Dermal exposure to aliphatic and aromatic isocyanates can occur in various exposure settings. The fate of isocyanates on skin is an important unanswered question. Do they react and bind to the outer layer of skin or do they penetrate through the epidermis as unreacted compounds? Knowing the kinetics of these processes is important in developing dermal exposure sampling or decontamination strategies, as well as understanding potential health implications such exposure may have. In this paper the residence time of model isocyanates on hairless guinea pig skin was investigated in vitro using attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrometry. Model isocyanates tested were octyl isocyanate, polymeric hexamethylene diisocyanate isocyanurate (pHDI), polymeric isophorone diisocyanate isocyanurate (pIPDI) and methylenediphenyl diisocyanate (MDI). Isocyanates in ethyl acetate (30 microL) were spiked directly on the skin to give 0.2-1.8 micromol NCO cm(-2) (NCO = -N=C=O), and absorbance of the isocyanate group and other chemical groups of the molecule were monitored over time. The ATR-FTIR findings showed that polymeric isocyanates pHDI and pIPDI may remain on the skin as unreacted species for many hours, with only 15-20% of the total isocyanate group disappearing in one hour, while smaller compounds octyl isocyanate and MDI rapidly disappear from the skin surface (80+% in 30 min). Isocyanates most likely leave the skin surface by diffusion predominantly, with minimal reaction with surface proteins. The significance of these findings and their implications for dermal exposure sampling and isocyanate skin decontamination are discussed.

Microwave-assisted synthesis of isosorbide-derived diols for the preparation of thermally stable thermoplastic polyurethane

PubMed Central

Kasmi, Nejib; Roso, Martina; Hammami, Nadia; Majdoub, Mustapha; Boaretti, Carlo; Sgarbossa, Paolo; Vianello, Chiara; Maschio, Giuseppe; Modesti, Michele; Lorenzetti, Alessandra

2017-01-01

Abstract In order to prepare thermally stable isosorbide-derived thermoplastic polyurethane, the synthesis of two new chiral exo–exo configured diols, prepared from isosorbide, and two types of diphenols (bisphenol A and thiodiphenol) was described. The synthesis conditions were optimized under conventional heating and microwave irradiations. To prove their suitability in polymerization, these monomers were successfully polymerized using 4,4′-diphenylmethane diisocyanate (MDI) and hexamethylene diisocyanate (HDI). Both monomers and polymers have been studied by NMR, FT-IR, TGA, DSC; intrinsic viscosity of polymers has also been determined. The results showed the effectiveness of the synthetic strategy proposed; moreover, a dramatic reduction of the reaction time and an important improvement of the monomers yield using microwave irradiation have been demonstrated. The monomers, as well as the polymers, showed excellent thermal stability both in air and nitrogen. It was also shown that the introduction of sulphur in the polyurethane backbone was effective in delaying the onset of degradation as well as the degradation rate. PMID:29491826

Dermal, inhalation, and internal exposure to 1,6-HDI and its oligomers in car body repair shop workers and industrial spray painters.

PubMed

Pronk, A; Yu, F; Vlaanderen, J; Tielemans, E; Preller, L; Bobeldijk, I; Deddens, J A; Latza, U; Baur, X; Heederik, D

2006-09-01

To study inhalation and dermal exposure to hexamethylene diisocyanate (HDI) and its oligomers as well as personal protection equipment (PPE) use during task performance in conjunction with urinary hexamethylene diamine (HDA) in car body repair shop workers and industrial spray painters. Personal task based inhalation samples (n = 95) were collected from six car body repair shops and five industrial painting companies using impingers with di-n-butylamine (DBA) in toluene. In parallel, dermal exposure was assessed using nitril rubber gloves. Gloves were submerged into DBA in toluene after sampling. Analysis for HDI and its oligomers was performed by LC-MS/MS. Urine samples were collected from 55 workers (n = 291) and analysed for HDA by GC-MS. Inhalation exposure was strongly associated with tasks during which aerosolisation occurs. Dermal exposure occurred during tasks that involve direct handling of paint. In car body repair shops associations were found between detectable dermal exposure and glove use (odds ratio (OR) 0.22, 95% confidence interval (CI) 0.09 to 0.57) and inhalation exposure level (OR 1.34, 95% CI 0.97 to 1.84 for a 10-fold increase). HDA in urine could be demonstrated in 36% and 10% of car body repair shop workers and industrial painting company workers respectively. In car body repair shops, the frequency of detectable HDA was significantly elevated at the end of the working day (OR 2.13, 95% CI 1.07 to 4.22 for 3-6 pm v 0-8 am). In both branches HDA was detected in urine of approximately 25% of the spray painters. In addition HDA was detected in urine of a large proportion of non-spray painters in car body repair shops. Although (spray) painting with lacquers containing isocyanate hardeners results in the highest external exposures to HDI and oligomers, workers that do not perform paint related tasks may also receive a considerable internal dose.

Morphological and thermal studies of chitin-curcumin blends derived polyurethanes.

PubMed

Mahmood, Kashif; Zia, Khalid Mahmood; Zuber, Mohammad; Tabasum, Shazia; Rehman, Saima; Zia, Fatima; Noreen, Aqdas

2017-12-01

The present study describes a novel ecofriendly series of chitin/curcumin/1,4-butane diol (BDO) blend derived polyurethanes (PUs), using hydroxy terminated polybutadiene (HTPB) and hexamethylene diisocyanate (HDI) along with different mole ratio of chitin, curcumin and BDO. The structural and morphological elucidation of the prepared films was done by FTIR and SEM techniques. The swelling behavior of the films was analyzed in both water and DMSO, which showed that incorporation of chitin increases the hydrophobicity and decreases the rate of swelling. Thermal analysis of synthesized PU blends revealed better thermal stability with following mole ratio 1:0.5:0.5 of chitin: curcumin: BDO as determined by TGA and DSC techniques. Copyright © 2017 Elsevier B.V. All rights reserved.

Synthesis of a Novel Biodegradable Polyurethane with Phosphatidylcholines

PubMed Central

Cao, Jun; Chen, Niancao; Chen, Yuanwei; Luo, Xianglin

2010-01-01

A novel polyurethane was successfully synthesized by chain-extension of biodegradable poly (l-lactide) functionalized phosphatidylcholine (PC) with hexamethylene diisocyanate (HDI) as chain extender (PUR-PC). The molecular weights, glass transition temperature (Tg) increased significantly after the chain-extension. The hydrophilicity of PUR-PC was better than the one without PC, according to a water absorption test. Moreover, the number of adhesive platelets and anamorphic platelets on PUR-PC film were both less than those on PUR film. These preliminary results suggest that this novel polyurethane might be a better scaffold than traditional biodegradable polyurethanes for tissue engineering due to its better blood compatibility. Besides, this study also provides a new method to prepare PC-modified biodegradable polyurethanes. PMID:20480047

Cytocompatibility and Mechanical Properties of Short Phosphate Glass Fibre Reinforced Polylactic Acid (PLA) Composites: Effect of Coupling Agent Mediated Interface

PubMed Central

Hasan, Muhammad Sami; Ahmed, Ifty; Parsons, Andrew; Walker, Gavin; Scotchford, Colin

2012-01-01

In this study three chemical agents Amino-propyl-triethoxy-silane (APS), sorbitol ended PLA oligomer (SPLA) and Hexamethylene diisocyanate (HDI) were identified to be used as coupling agents to react with the phosphate glass fibre (PGF) reinforcement and the polylactic acid (PLA) polymer matrix of the composite. Composites were prepared with short chopped strand fibres (l = 20 mm, ϕ = 20 µm) in a random arrangement within PLA matrix. Improved, initial composite flexural strength (~20 MPa) was observed for APS treated fibres, which was suggested to be due to enhanced bonding between the fibres and polymer matrix. Both APS and HDI treated fibres were suggested to be covalently linked with the PLA matrix. The hydrophobicity induced by these coupling agents (HDI, APS) helped to resist hydrolysis of the interface and thus retained their mechanical properties for an extended period of time as compared to non-treated control. Approximately 70% of initial strength and 65% of initial modulus was retained by HDI treated fibre composites in contrast to the control, where only ~50% of strength and modulus was retained after 28 days of immersion in PBS at 37 °C. All coupling agent treated and control composites demonstrated good cytocompatibility which was comparable to the tissue culture polystyrene (TCP) control, supporting the use of these materials as coupling agent’s within medical implant devices. PMID:24955744

Immunological evaluation of four arc welders exposed to fumes from ignited polyurethane (isocyanate) foam: antibodies and immune profiles

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broughton, A.; Thrasher, J.D.; Gard, Z.

1988-01-01

Four arc welders having a flu-like illness with multiple health complaints following an exposure to high concentrations of isocyanate fumes from ignited polyurethane foam underwent immunological tests as follows: ELISA antibody assays, activated lymphocyte profiles, and lymphocyte blastogenesis. ELISA procedures revealed the presence of antibodies to hexamethylene diisocyanate (HDI) and formaldehyde (F) conjugated to human serum albumin (HDI-SA and F-SA). The results from the activated lymphocyte profiles showed deviations from the norm as follows: three welders had elevated helper/suppressor (H/S) ratios; all four had elevated percentages of Tal positive cells; two had decreases in B cells; and one had lowmore » total white cell and lymphocyte counts. In contrast, the percentage and absolute numbers of ILS receptor cells were normal in the four subjects. T cell blastogenesis to PHA, Con A and PWM resulted in the following: T-cells from one subject responded normally; in another, a high response (212% of controls) to PHA occurred with normal mitogenesis to Con A and PWM. In the remaining two welders, the T cells responded abnormally low (50 to 75% of controls) to the three mitogens. In conclusion, the existence of IgG antibodies to HDI-SA and F-SA, the altered activated immune profiles, the elevated Tal cells, and the abnormal blastogenesis are interpreted as being linked with the episode of HDI and F exposure and the subsequent flu-like illness of the four welders.« less

Dermal, inhalation, and internal exposure to 1,6‐HDI and its oligomers in car body repair shop workers and industrial spray painters

PubMed Central

Pronk, A; Yu, F; Vlaanderen, J; Tielemans, E; Preller, L; Bobeldijk, I; Deddens, J A; Latza, U; Baur, X; Heederik, D

2006-01-01

Objectives To study inhalation and dermal exposure to hexamethylene diisocyanate (HDI) and its oligomers as well as personal protection equipment (PPE) use during task performance in conjunction with urinary hexamethylene diamine (HDA) in car body repair shop workers and industrial spray painters. Methods Personal task based inhalation samples (n = 95) were collected from six car body repair shops and five industrial painting companies using impingers with di‐n‐butylamine (DBA) in toluene. In parallel, dermal exposure was assessed using nitril rubber gloves. Gloves were submerged into DBA in toluene after sampling. Analysis for HDI and its oligomers was performed by LC‐MS/MS. Urine samples were collected from 55 workers (n = 291) and analysed for HDA by GC‐MS. Results Inhalation exposure was strongly associated with tasks during which aerosolisation occurs. Dermal exposure occurred during tasks that involve direct handling of paint. In car body repair shops associations were found between detectable dermal exposure and glove use (odds ratio (OR) 0.22, 95% confidence interval (CI) 0.09 to 0.57) and inhalation exposure level (OR 1.34, 95% CI 0.97 to 1.84 for a 10‐fold increase). HDA in urine could be demonstrated in 36% and 10% of car body repair shop workers and industrial painting company workers respectively. In car body repair shops, the frequency of detectable HDA was significantly elevated at the end of the working day (OR 2.13, 95% CI 1.07 to 4.22 for 3–6 pm v 0–8 am). In both branches HDA was detected in urine of ∼25% of the spray painters. In addition HDA was detected in urine of a large proportion of non‐spray painters in car body repair shops. Conclusion Although (spray) painting with lacquers containing isocyanate hardeners results in the highest external exposures to HDI and oligomers, workers that do not perform paint related tasks may also receive a considerable internal dose. PMID:16728504

N-halamine-based rechargeable antimicrobial and biofilm-controlling polyurethane

PubMed Central

Sun, Xinbo; Cao, Zhengbing; Porteous, Nuala; Sun, Yuyu

2012-01-01

An N-halamine precursor, 5, 5-dimethyl hydantoin (DMH), was covalently linked to the surface of polyurethane (PU) with 1,6-hexamethylene diisocyanate (HDI) as a coupling agent. The reaction pathways were investigated using propyl isocyanate (PI) as a model compound, and the results suggested that the imide and amide groups of DMH had very similar reactivity toward the isocyanate groups on PU surfaces activated with HDI. After bleach treatment, the covalently bound DMH moieties were transformed into N-halamines. The new N-halmaine-based PU provided potent antimicrobial effects against Staphylococcus aureus (S. aureus, Gram-positive), Escherichia coli (E. coli, Gram-negative), methicillin-resistant staphylococcus aureus (MRSA, drug resistant Gram-positive bacteria), vancomycin-resistant enterococcus (VRE, drug resistant Gram-positive bacteria), and Candida albicans (C. ablicans, fungi), and successfully prevented bacterial and fungal biofilm formation. The antimicrobial and biofilm-controlling effects were stable for longer than 6 months under normal storage in open air. Furthermore, if the functions were lost due to prolonged use, they could be recharged by another chlorination treatment. The recharging could be repeated as needed to achieve long-term protection against microbial contamination and biofilm-formation. PMID:22244984

Gelatin-Modified Polyurethanes for Soft Tissue Scaffold

PubMed Central

Kucińska-Lipka, Justyna; Janik, Helena

2013-01-01

Recently, in the field of biomaterials for soft tissue scaffolds, the interest of their modification with natural polymersis growing. Synthetic polymers are often tough, and many of them do not possess fine biocompatibility. On the other hand, natural polymers are biocompatible but weak when used alone. The combination of natural and synthetic polymers gives the suitable properties for tissue engineering requirements. In our study, we modified gelatin synthetic polyurethanes prepared from polyester poly(ethylene-butylene adipate) (PEBA), aliphatic 1,6-hexamethylene diisocyanate (HDI), and two different chain extenders 1,4-butanediol (BDO) or 1-ethoxy-2-(2-hydroxyethoxy)ethanol (EHEE). From a chemical point of view, we replaced expensive components for building PU, such as 2,6-diisocyanato methyl caproate (LDI) and 1,4-diisocyanatobutane (BDI), with cost-effective HDI. The gelatin was added in situ (in the first step of synthesis) to polyurethane to increase biocompatibility and biodegradability of the obtained material. It appeared that the obtained gelatin-modified PU foams, in which chain extender was BDO, had enhanced interactions with media and their hydrolytic degradation profile was also improved for tissue engineering application. Furthermore, the gelatin introduction had positive impact on gelatin-modified PU foams by increasing their hemocompatibility. PMID:24363617

Self-repairable polyurethane networks by atmospheric carbon dioxide and water.

PubMed

Yang, Ying; Urban, Marek W

2014-11-03

Sugar moieties were incorporated into cross-linked polyurethane (PUR) networks in an effort to achieve self-repairing in the presence of atmospheric carbon dioxide (CO2) and water (H2O). When methyl-α-D-glucopyranoside (MGP) molecules are reacted with hexamethylene diisocyanate trimer (HDI) and polyethylene glycol (PEG) to form cross-linked MGP-polyurethane (PUR) networks, these materials are capable of self-repairing in air. This process requires atmospheric amounts of CO2 and H2O, thus resembling plant behavior of carbon fixation during the photosynthesis cycle. Molecular processes responsible for this unique self-repair process involve physical diffusion of cleaved network segments as well as the formation of carbonate and urethane linkages. Unlike plants, MGP-PUR networks require no photo-initiated reactions, and they are thus capable of repair in darkness under atmospheric conditions. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

[Synthesis and characterization of polylactide-based thermosetting polyurethanes with shape memory properties].

PubMed

Shi, Shuo; Gu, Lin; Yang, Yihu; Yu, Haibin; Chen, Rui; Xiao, Xianglian; Qiu, Jun

2016-06-25

A series of bio-based thermosetting polyurethanes (Bio-PUs) were synthesized by the crosslinking reaction of polylactide and its copolymers diols with hexamethylene diisocyanate (HDI) trimer. The obtained Bio-PUs were characterized by Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), Thermal Gravimetric Analysis (TGA), universal tensile testing machine and cytotoxicity test. Results indicate that the PLA copolymer (P(LA-co-CL)) diols reduced the glass transition temperature (Tg) of Bio-PUs and improved their thermal stability, compared with PLA diols. The Bio-PUs synthesized from P (LA-co-CL) diols exhibit better mechanical performance and shape memory properties. Especially, Young modulus and elongation at break of the obtained Bio-PUs were 277.7 MPa and 230% respectively; the shape recovery time of the obtained Bio-PUs at body temperature was only 93 s. Furthermore, alamar blue assay results showed that the obtained Bio-PUs had no cell toxicity.

Development of segmented polyurethane elastomers with low iodine content exhibiting radiopacity and blood compatibility.

PubMed

Dawlee, S; Jayabalan, Muthu

2011-10-01

Biofunctionally active and inherently radiopaque polymers are the emerging need for biomedical applications. Novel segmented polyurethane elastomer with inherent radiopacity was prepared using aliphatic chain extender 2,3-diiodo-2-butene-1,4-diol, polyol polytetramethylene glycol and 4,4'-methylenebis(phenyl isocyanate) (MDI) for blood compatible applications. Aliphatic polyurethane was also prepared using hexamethylene diisocyanate for comparison. X-ray analysis of the polyurethanes revealed good radiopacity even at a relatively low concentration of 3% iodine in aromatic polyurethane and 10% in aliphatic polyurethane. The polyurethanes also possessed excellent thermal stability. MDI-based polyurethane showed considerably higher tensile strength than the analogous HDI-based polyurethane. MDI-based aromatic polyurethane exhibited a dynamic surface morphology in aqueous medium, resulting in the segregation of hydrophilic domains which was more conducive to anti-thrombogenic properties. The polyurethane was cytocompatible with L929 fibroblast cells, non-hemolytic, and possessed good blood compatibility.

Determination of technical grade isocyanates used in the production of polyurethane plastics.

PubMed

Marand, Asa; Dahlin, Jakob; Karlsson, Daniel; Skarping, Gunnar; Dalene, Marianne

2004-07-01

A method for determination of technical grade isocyanates used in the production of polyurethane (PUR) is presented. The isocyanates in technical grade products were characterised as di-n-butylamine (DBA) derivatives using LC-MS and LC-chemiluminescent nitrogen detection (CLND) and the total isocyanate content was compared to a titration assay. For collection of isocyanates in air, an impinger-filter sampling technique with DBA as derivatisation reagent was used. Characterised DBA and nonadeuterium labelled DBA derivatives of isocyanates in technical products were used as calibration standards and internal standards, respectively, in the analysis of air samples. Three workplaces were studied where PUR products were produced either by spraying or by moulding. In both technical products and in air samples, a number of monomeric, oligomeric and prepolymeric isocyanates of e.g. methylenebisphenyl diisocyanate (MDI) and hexamethylene diisocyanate (HDI) were characterised. Several of these have not previously been described in workplace atmospheres. In the technical isocyanate products, between 69 and 102% of the NCO content determined by titration was accounted for by LC-CLND. Quantifications of a wide range of isocyanates in air samples were performed with correlation coefficients in the range 0.988-0.999 (n= 8) and the instrumental detection limits were 0.7-25 pg. At the two workplaces where MDI- and HDI isocyanurate-based products were sprayed, the isocyanate composition in the air reflected the composition in the technical product. At the workplace where a MDI-based product was used in a moulding process, only the monomeric isocyanates were found in the air. The advantage of using characterised technical grade isocyanates as analytical standards was clearly demonstrated and the possibility of using index compounds when monitoring isocyanate exposure is discussed.

Synthesis and Characterization of Biodegradable Polyurethane for Hypopharyngeal Tissue Engineering

PubMed Central

Shen, Zhisen; Lu, Dakai; Li, Qun; Zhang, Zongyong

2015-01-01

Biodegradable crosslinked polyurethane (cPU) was synthesized using polyethylene glycol (PEG), L-lactide (L-LA), and hexamethylene diisocyanate (HDI), with iron acetylacetonate (Fe(acac)3) as the catalyst and PEG as the extender. Chemical components of the obtained polymers were characterized by FTIR spectroscopy, 1H NMR spectra, and Gel Permeation Chromatography (GPC). The thermodynamic properties, mechanical behaviors, surface hydrophilicity, degradability, and cytotoxicity were tested via differential scanning calorimetry (DSC), tensile tests, contact angle measurements, and cell culture. The results show that the synthesized cPU possessed good flexibility with quite low glass transition temperature (T g, −22°C) and good wettability. Water uptake measured as high as 229.7 ± 18.7%. These properties make cPU a good candidate material for engineering soft tissues such as the hypopharynx. In vitro and in vivo tests showed that cPU has the ability to support the growth of human hypopharyngeal fibroblasts and angiogenesis was observed around cPU after it was implanted subcutaneously in SD rats. PMID:25839041

Synthesis and characterization of biodegradable polyurethane for hypopharyngeal tissue engineering.

PubMed

Shen, Zhisen; Lu, Dakai; Li, Qun; Zhang, Zongyong; Zhu, Yabin

2015-01-01

Biodegradable crosslinked polyurethane (cPU) was synthesized using polyethylene glycol (PEG), L-lactide (L-LA), and hexamethylene diisocyanate (HDI), with iron acetylacetonate (Fe(acac)3) as the catalyst and PEG as the extender. Chemical components of the obtained polymers were characterized by FTIR spectroscopy, (1)H NMR spectra, and Gel Permeation Chromatography (GPC). The thermodynamic properties, mechanical behaviors, surface hydrophilicity, degradability, and cytotoxicity were tested via differential scanning calorimetry (DSC), tensile tests, contact angle measurements, and cell culture. The results show that the synthesized cPU possessed good flexibility with quite low glass transition temperature (T g , -22°C) and good wettability. Water uptake measured as high as 229.7 ± 18.7%. These properties make cPU a good candidate material for engineering soft tissues such as the hypopharynx. In vitro and in vivo tests showed that cPU has the ability to support the growth of human hypopharyngeal fibroblasts and angiogenesis was observed around cPU after it was implanted subcutaneously in SD rats.

Development of Photocrosslinkable Urethane-Doped Polyester Elastomers for Soft Tissue Engineering

PubMed Central

Zhang, Yi; Tran, Richard T.; Gyawali, Dipendra; Yang, Jian

2012-01-01

Finding an ideal biomaterial with the proper mechanical properties and biocompatibility has been of intense focus in the field of soft tissue engineering. This paper reports on the synthesis and characterization of a novel crosslinked urethane-doped polyester elastomer (CUPOMC), which was synthesized by reacting a previously developed photocrosslinkable poly (octamethylene maleate citrate) (POMC) prepolymers (pre-POMC) with 1,6-hexamethylene diisocyanate (HDI) followed by thermo- or photo-crosslinking polymerization. The mechanical properties of the CUPOMCs can be tuned by controlling the molar ratios of pre-POMC monomers, and the ratio between the prepolymer and HDI. CUPOMCs can be crosslinked into a 3D network through polycondensation or free radical polymerization reactions. The tensile strength and elongation at break of CUPOMC synthesized under the known conditions range from 0.73±0.12MPa to 10.91±0.64MPa and from 72.91±9.09% to 300.41±21.99% respectively. Preliminary biocompatibility tests demonstrated that CUPOMCs support cell adhesion and proliferation. Unlike the pre-polymers of other crosslinked elastomers, CUPOMC pre-polymers possess great processability demonstrated by scaffold fabrication via a thermally induced phase separation method. The dual crosslinking methods for CUPOMC pre-polymers should enhance the versatile processability of the CUPOMC used in various conditions. Development of CUPOMC should expand the choices of available biodegradable elastomers for various biomedical applications such as soft tissue engineering. PMID:23565318

FTIR and molecular mechanics studies of H-bonds in aliphatic polyurethane and polyamide-66 model molecules.

PubMed

Wang, Guoqing; Zhang, Chunxia; Guo, Xiaohe; Ren, Zhiyong

2008-02-01

Model aliphatic polyurethane (APU) hard segment based on 1,6-hexamethylene diisocyanate (HDI) and 1,4-butanediol (BDO) were prepared. FTIR and molecular mechanics (MM) simulation were used to conduct the systematic studies on APU and polyamide-66 (PA-66) whose sole difference lies in the alkoxyl oxygen. It was found that the introduction of the alkoxyl not only increases the conformations in APU, makes it a possible H-bond acceptor, but also weakens the H-bond between NH and O=C in APU. There are two conformers stably existed in APU with lowest energy, leading to eight H-bond complexes based on NH as donor and (1) O=C as acceptor, and another two complexes based on (2) alkoxyl O and (3) urethane N as acceptors, whereas there is only one stable conformer in PA-66, leading to one H-bond complex. One predominant H-bond complex has been found in APU with probability of about 95%. The simulated results are consistent with the nuNH and nuC=O band shifting in FTIR.

FTIR and molecular mechanics studies of H-bonds in aliphatic polyurethane and polyamide-66 model molecules

NASA Astrophysics Data System (ADS)

Wang, Guoqing; Zhang, Chunxia; Guo, Xiaohe; Ren, Zhiyong

2008-02-01

Model aliphatic polyurethane (APU) hard segment based on 1,6-hexamethylene diisocyanate (HDI) and 1,4-butanediol (BDO) were prepared. FTIR and molecular mechanics (MM) simulation were used to conduct the systematic studies on APU and polyamide-66 (PA-66) whose sole difference lies in the alkoxyl oxygen. It was found that the introduction of the alkoxyl not only increases the conformations in APU, makes it a possible H-bond acceptor, but also weakens the H-bond between NH and O dbnd C in APU. There are two conformers stably existed in APU with lowest energy, leading to eight H-bond complexes based on NH as donor and (1) O dbnd C as acceptor, and another two complexes based on (2) alkoxyl O and (3) urethane N as acceptors, whereas there is only one stable conformer in PA-66, leading to one H-bond complex. One predominant H-bond complex has been found in APU with probability of about 95%. The simulated results are consistent with the νNH and νC dbnd O band shifting in FTIR.

Understanding Factors that Influence Protective Glove Use among Automotive Spray Painters

PubMed Central

Ceballos, Diana; Reeb-Whitaker, Carolyn; Glazer, Patricia; Murphy-Robinson, Helen; Yost, Michael

2017-01-01

Dermal contact with isocyanate-based coatings may lead to systemic respiratory sensitization. The most common isocyanates found in sprayed automotive coatings are monomeric and oligomeric 1,6-hexamethylene diisocyanate (HDI) and isophorone diisocyanate (IPDI). Most spray painters use thin (4–5 mil) latex gloves that are not effective at preventing dermal exposures when spraying isocyanate paints. Personal interviews with collision repair industry personnel and focus groups with spray painters were held to characterize risk awareness, to examine perceptions and challenges concerning protective glove use and selection, and to generate ideas for protective glove use interventions. The most popular gloves among spray painters were thin (4–5 mil) and thick (14 mil) latex. We found that medium to thick (6–8 mil) nitrile were not always perceived as comfortable and were expected to be more expensive than thin (4–5 mil) latex gloves. Of concern is the users’ difficulty to distinguish between nitrile and latex gloves; latex gloves are now sold in different colors including blue, which has traditionally been associated with nitrile gloves. Even though spray painters were familiar with the health hazards related to working with isocyanate paints; most were not always aware that dermal exposure to isocyanates could contribute to the development of occupational asthma. There is a need for more research to identify dermal materials that are protective against sprayed automotive coatings. Automotive spray painters and their employers need to be educated in the selection and use of protective gloves, specifically on attributes such as glove material, color, and thickness. PMID:24215135

The effect of oxidation on the enzyme-catalyzed hydrolytic biodegradation of poly(urethane)s.

PubMed

Labow, Rosalind S; Tang, Yiwen; McCloskey, Christopher B; Santerre, J Paul

2002-01-01

Although the biodegradation of polyurethanes (PU) by oxidative and hydrolytic agents has been studied extensively, few investigations have reported on the combination of their effects. Since neutrophils (PMN) arrive at an implanted device first and release HOCl, followed by monocyte-derived macrophages (MDM) which have potent esterase activities and oxidants of their own, the combined effect of oxidative and hydrolytic degradation on radiolabeled polycarbonate-polyurethanes (PCNU)s was investigated and compared to that of a polyester-PU (PESU) and a polyether-PU (PEU). The PCNUs were synthesized with PCN (MW = 1,000), and butanediol (14C-BD) and one of two diisocyanates, hexane-1,6-diisocyanate (14C-HDI) or methylene bis-p-phenyl diisocyanate (MDI). The PESU and PEU were synthesized using toluene-diisocyanate (14C-TDI), with polycaprolactone and polytetramethylene oxide as soft segments respectively, and ethylene diamine as the chain extender. The effect of pre-treatment with 0.1 mM HOC1 for 1 week on the HDI-based PCNUs and both TDI-based PUs resulted in a significant inhibition of radiolabel release (RR) elicited by cholesterol esterase (CE), when compared to buffer alone, whereas the MDI-based PCNU showed a small but significant increase. When PMN were activated on the HDI-based PCNU surface with phorbol myristate acetate (PMA), HOCl was released for 3 h, and was almost completely abolished by sodium azide (AZ). Simultaneously, the PMN-elicited RR, shown previously to be due to the esterolytic cleavage by serine proteases, was inhibited approximately 75% by PMA-activation of the cells, but significantly increased relative to the latter when AZ was added. Both in vitro oxidation by HOCl and the release of HOCI by PMN were associated with the inhibition of RR and suggest perturbations between oxidative and hydrolytic mechanisms of biodegradation.

In vitro and biomechanical screening of polyethylene glycol and poly(trimethylene carbonate) block copolymers for annulus fibrosus repair.

PubMed

Long, Rose G; Rotman, Stijn G; Hom, Warren W; Assael, Dylan J; Illien-Jünger, Svenja; Grijpma, Dirk W; Iatridis, James C

2018-02-01

Herniated intervertebral discs (IVDs) are a common cause of back and neck pain. There is an unmet clinical need to seal annulus fibrosus (AF) defects, as discectomy surgeries address acute pain but are complicated by reherniation and recurrent pain. Copolymers of polyethylene glycol with trimethylene carbonate (TMC) and hexamethylene diisocyanate (HDI) end-groups were formulated as AF sealants as the HDI form covalent bonds with native AF tissue. TMC adhesives were evaluated and optimized using the design criteria: stable size, strong adherence to AF tissue, high cytocompatibility, restoration of IVD biomechanics to intact levels following in situ repair, and low extrusion risk. TMC adhesives had high adhesion strength as assessed with a pushout test (150 kPa), and low degradation rates over 3 weeks in vitro. Both TMC adhesives had shear moduli (220 and 490 kPa) similar to, but somewhat higher than, AF tissue. The adhesive with three TMC moieties per branch (TMC3) was selected for additional in situ testing because it best matched AF shear properties. TMC3 restored torsional stiffness, torsional hysteresis area and axial range of motion to intact states. However, in a failure test of compressive deformation under fixed 5 ° flexion, some herniation risk was observed with failure strength of 5.9 MPa compared with 13.5 MPa for intact samples; TMC3 herniated under cyclic organ culture testing. These TMC adhesives performed well during in vitro and in situ testing, but additional optimization to enhance failure strength is required to further this material to advanced screening tests, such as long-term degradation. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

A Novel Polar Copolymer Design as a Multi-Functional Binder for Strong Affinity of Polysulfides in Lithium-Sulfur Batteries

NASA Astrophysics Data System (ADS)

Jiao, Yu; Chen, Wei; Lei, Tianyu; Dai, Liping; Chen, Bo; Wu, Chunyang; Xiong, Jie

2017-03-01

High energy density, low cost and environmental friendliness are the advantages of lithium-sulfur (Li-S) battery which is regarded as a promising device for electrochemical energy storage systems. As one of the important ingredients in Li-S battery, the binder greatly affects the battery performance. However, the conventional binder has some drawbacks such as poor capability of absorbing hydrophilic lithium polysulfides, resulting in severe capacity decay. In this work, we reported a multi-functional polar binder (AHP) by polymerization of hexamethylene diisocyanate (HDI) with ethylenediamine (EDA) bearing a large amount of amino groups, which were successfully used in electrode preparation with commercial sulfur powder cathodes. The abundant amide groups of the binder endow the cathode with multidimensional chemical bonding interaction with sulfur species within the cathode to inhibit the shuttling effect of polysulfides, while the suitable ductility to buffer volume change. Utilizing these advantageous features, composite C/S cathodes based the binder displayed excellent capacity retention at 0.5 C, 1 C, 1.5 C, and 3 C over 200 cycles. Accompany with commercial binder, AHP may act as an alternative feedstock to open a promising approach for sulfur cathodes in rechargeable lithium battery to achieve commercial application.

Biomarkers of exposure, antibodies, and respiratory symptoms in workers heating polyurethane glue.

PubMed Central

Skarping, G; Dalene, M; Svensson, B G; Littorin, M; Akesson, B; Welinder, H; Skerfving, S

1996-01-01

OBJECTIVES: The pathogenic basis of respiratory disorders associated with isocyanates are still obscure. One reason for this is the lack of good estimates of human exposure. In this study exposure was estimated by measurement of isocyanate metabolites in biological samples. METHODS: In a factory using isocyanate based polyurethane (PUR) glue, isocyanate concentrations in air were measured by liquid chromatography. Samples from 174 employees were analysed for metabolites of 4,4'-methylene diphenyl diisocyanate (MDI) in plasma (P-MDX) and urine (U-MDX). After hydrolysis, 4,4'-methylenedianiline was measured by gas chromatography-mass spectrometry (GC-MS). The employees were screened for work related respiratory symptoms and tested for specific immunoglobulin E (IgE) and IgG antibodies directed against isocyanate conjugated to human serum albumin. RESULTS: The time weighted isocyanate concentrations in air were low (MDI < 0.2-7; hexamethylene diisocyanate (HDI) < 0.1-0.7; 2,6-toluene diisocyanate (TDI) < 0.1 microgram/m3). All subjects had detectable P-MDX and U-MDX. There were significant associations between the estimates of exposure to thermal degradation products of an MDI based glue and P-MDX (range < or = 0.10-5.5 micrograms/l); and U-MDX (< or = 0.04-5.0 micrograms/g creatinine); in cases of heavy exposure. P-MDX and U-MDX were associated with each other (r = 0.64; P = 0.0001), work related symptoms (P-MDX: P = 0.03; Mann-Whitney U test), and serum concentrations of MDI specific IgG antibodies (r = 0.26; P = 0.0007). Unexpectedly, high P-MDX and U-MDX concentrations were also encountered in workers cutting textile (P-MDX 2.4-4.5 micrograms/l; U-MDX 0.81-3.8 micrograms/g creatinine); the reason is still unknown. Equally unexpected, there were significant negative associations between P-MDX and liver function tests. CONCLUSIONS: The results clearly show the value of biomarkers for isocyanate exposure; in particular, P-MDX is useful. Further, these results show the risk connected with thermal degradation of PUR. PMID:8704859

Synthesis and characterization of thiolated carboxymethyl chitosan-graft-cyclodextrin nanoparticles as a drug delivery vehicle for albendazole.

PubMed

Alamdarnejad, Ghazaleh; Sharif, Alireza; Taranejoo, Shahrouz; Janmaleki, Mohsen; Kalaee, Mohammad Reza; Dadgar, Mohsen; Khakpour, Mazyar

2013-08-01

A new strategy for the synthesis of thiolated carboxymethyl chitosan-g-cyclodextrin nanoparticles by an ionic-gelation method is presented. The synthetic approach was based on the utilization of 1,6-hexamethylene diisocyanate during cyclodextrin grafting onto carboxymethyl chitosan. The use of the 1,6-hexamethylene diisocyanate resulted in reactions between cyclodextrin and active sites at the C6-position of chitosan, and preserved amino groups of chitosan for subsequent reactions with thioglycolic acid, as the thiolating agent, and tripolyphosphate, as the gelling counterion. Various methods such as scanning electron microscopy, rheology and in vitro release studies were employed to exhibit significant features of the nanoparticles for mucosal albendazole delivery applications. It was found that the thiolated carboxymethyl chitosan-g-cyclodextrin nanoparticles prepared using an aqueous solution containing 1 wt% of tripolyphosphate and having 115.65 (μmol/g polymer) of grafted thiol groups show both the highest mucoadhesive properties and the highest albendazole entrapment efficiency. The latter was confirmed theoretically by calculating the enthalpy of mixing of albendazole in the above thiolated chitosan polymer.

Preparation and Characterization of Polyurethanes with Cross-Linked Siloxane in the Side Chain by Sol-Gel Reactions

PubMed Central

Zhao, Hui; Hao, Tong-Hui; Hu, Guo-Hua; Shi, Dean; Huang, Da; Jiang, Tao; Zhang, Qun-Chao

2017-01-01

A series of novel polyurethanes containing cross-linked siloxane in the side chain (SPU) were successfully synthesized through a sol-gel process. The SPU was composed of 0%–20% N-(n-butyl)-3-aminopropyltriethoxysilane (HDI-T) modified hexamethylene diisocynate homopolymer. The effects of HDI-T content on both the structure and properties of SPU were investigated by Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), mechanical properties tests, gel content test, water contact angle measurement and water absorption test. FT-IR, XPS and XRD results confirmed the successful incorporation of HDI-T onto polyurethanes and the formation of Si–O–Si. The surface roughness and the Si content of SPU enhanced with the increase of HDI-T content. Both crystallization and melting temperature shifted to a lower point after the incorporation of HDI-T. The hydrophobicity, tensile strength, Young’s modulus and pencil hardness overall increased with the increasing of HDI-T content, whereas the thermal stability and the elongation at break of SPU slightly decreased. PMID:28772607

Development of a biodegradable tissue adhesive based on functionalized 1,2-ethylene glycol bis(dilactic acid). II.

PubMed

Rohm, Henning W; Lurtz, Claudia; Wegmann, Juergen; Odermatt, Erich K; Behrend, Detlef; Schmitz, Klaus-Peter; Sternberg, Katrin

2011-04-01

In body regions where damage and bleeding must be avoided, a substitute for mechanical tissue fixation by sutures or staplers is needed. Since tissue adhesives provide easy and fast handling they are a promising alternative. The present study reports the development and analysis of a tissue adhesive that consists of two adhesive components: hexamethylene diisocyanate (HDI) functionalized 1,2-ethylene glycol bis(dilactic acid) (ELA-NCO) and chitosan chloride. This composition was chosen based on preliminary studies on several chain elongation agents. The present study evaluates this adhesive system by IR-spectroscopy, tensile tests, and gel point measurements in comparison to fibrin glue. The system's in vitro biocompatibility was tested with mouse fibroblasts (L929) according to ISO 10993-5. Furthermore, an implantation study was performed in SPF-Wistar rats. The adhesive strength of manually applied mixtures or mixtures applied by double chamber syringes with a mixing extruder was determined to be significantly higher than that of fibrin glue on bovine muscle tissue at 37°C. Tensile strength increased further when exposure time of the adhesive was increased from 10 min to 48 h. The rheological gel point determination showed that the mixture of ELA-NCO/DMSO and chitosan chloride offers a time window large enough to readjust the fused joint during surgery, as opposed to fibrin glue. Additionally, the in vitro and in vivo biocompatibility studies of the adhesive system revealed no toxic effects on the surrounding tissue. Copyright © 2010 Wiley Periodicals, Inc.

Field Evaluation of Solvent-Free Sampling with Di-n-butylamine for the Determination of Airborne Monomeric and Oligomeric 1,6-Hexamethylene Diisocyanate

DTIC Science & Technology

2014-03-27

cause contact dermatitis , asthma, and hypersensitivity pneumonitis; the most common adverse health outcome associated with isocyanate exposure is...linked to allergic contact dermatitis in humans and respiratory sensitization in animals. Chronic dermal exposure has resulted in skin irritation and...derivatization stabilizes the highly reactive isocyanates and enhances recovery of the isocyanates that do not come into contact with the derivatization

Personnel Exposure to Airborne Isocyanates and Solvents During Shipboard Painting With 2-Pack Polyurethane Paints

DTIC Science & Technology

2008-12-01

contain low volatility isocyanate prepolymers in addition to small quantities of volatile isocyanate monomers [2,3]. The monomers may become airborne as...vapour whilst the non-volatile prepolymers and partially cured oligomers may form aerosols during spray painting and sanding of the painted surface...JL (1992) “ Prepolymers of hexamethylene diisocyanate as a cause of occupational asthma” J. Allergy Clinical Immunol. 91 850-61. 5. Redlich CA, Bello

Poly(iohexol) nanoparticles as contrast agents for in vivo X-ray computed tomography imaging.

PubMed

Yin, Qian; Yap, Felix Y; Yin, Lichen; Ma, Liang; Zhou, Qin; Dobrucki, Lawrence W; Fan, Timothy M; Gaba, Ron C; Cheng, Jianjun

2013-09-18

Biocompatible poly(iohexol) nanoparticles, prepared through cross-linking of iohexol and hexamethylene diisocyanate followed by coprecipitation of the resulting cross-linked polymer with mPEG-polylactide, were utilized as contrast agents for in vivo X-ray computed tomography (CT) imaging. Compared to conventional small-molecule contrast agents, poly(iohexol) nanoparticles exhibited substantially protracted retention within the tumor bed and a 36-fold increase in CT contrast 4 h post injection, which makes it possible to acquire CT images with improved diagnosis accuracy over a broad time frame without multiple administrations.

The respiratory local lymph node assay as a tool to study respiratory sensitizers.

PubMed

Arts, Josje H E; de Jong, Wim H; van Triel, Jos J; Schijf, Marcel A; de Klerk, Arja; van Loveren, Henk; Kuper, C Frieke

2008-12-01

The local lymph node assay (LLNA) is used to test the potential of low molecular weight (LMW) compounds to induce sensitization via the skin. In the present study, a respiratory LLNA was developed. Male BALB/c mice were exposed head/nose-only during three consecutive days for 45, 90, 180, or 360 min/day to various LMW allergens. Ear application (skin LLNA) was used as a positive control. Negative controls were exposed to the vehicle. Three days after the last exposure, proliferation was determined in the draining mandibular lymph nodes, and the respiratory tract was examined microscopically. Upon inhalation, the allergens trimellitic anhydride, phthalic anhydride, hexamethylene diisocyanate, toluene diisocyanate, isophorone diisocyanate (IPDI), dinitrochlorobenzene, and oxazolone were positive and showed stimulation indices (SIs) up to 11, whereas trimeric IPDI, formaldehyde, and methyl salicylate were negative (viz. SI < 3). All compounds, except trimeric IPDI, induced histopathological lesions predominantly in the upper respiratory tract. Exposure by inhalation is a realistic approach to test respiratory allergens. However, based on the local toxicity, the dose that can be applied is (generally) much lower than can be achieved by skin application. It is concluded that strong LMW allergens, regardless their immunological nature, besides the skin can also sensitize the body via the respiratory tract. In addition, the contact allergens were as potent as the respiratory allergens, although the potency ranking differed from that in a skin LLNA.

Properties of Graphene/Shape Memory Thermoplastic Polyurethane Composites Actuating by Various Methods

PubMed Central

Park, Jin Ho; Dao, Trung Dung; Lee, Hyung-il; Jeong, Han Mo; Kim, Byung Kyu

2014-01-01

Shape memory behavior of crystalline shape memory polyurethane (SPU) reinforced with graphene, which utilizes melting temperature as a shape recovery temperature, was examined with various external actuating stimuli such as direct heating, resistive heating, and infrared (IR) heating. Compatibility of graphene with crystalline SPU was adjusted by altering the structure of the hard segment of the SPU, by changing the structure of the graphene, and by changing the preparation method of the graphene/SPU composite. The SPU made of aromatic 4,4′-diphenylmethane diisocyanate (MSPU) exhibited better compatibility with graphene, having an aromatic structure, compared to that made of the aliphatic hexamethylene diisocyanate. The finely dispersed graphene effectively reinforced MSPU, improved shape recovery of MSPU, and served effectively as a filler, triggering shape recovery by resistive or IR heating. Compatibility was enhanced when the graphene was modified with methanol. This improved shape recovery by direct heating, but worsened the conductivity of the composite, and consequently the efficiency of resistive heating for shape recovery also declined. Graphene modified with methanol was more effective than pristine graphene in terms of shape recovery by IR heating. PMID:28788529

Thermoresponsive Polyurethane Bearing Oligo(Ethylene Glycol) as Side Chain Without Polyol at Polymer Backbone Achieved Excellent Hydrophilic and Hydrophobic Switching.

PubMed

Aoki, Daisuke; Ajiro, Hiroharu

2018-06-13

In order to prepare thermoresponsive polyurethane gels, a novel polyurethane bearing oligo(ethylene glycol) (OEG) as the side chain is successfully synthesized with hexamethylene diisocyanate and OEG tartrate ester. The aqueous solution of the polyurethane shows sharp and clear lower critical solution temperature behavior at 34 °C. Furthermore, a hydrogel based on the same polyurethane is also successfully prepared using glycerol as the crosslinker. This polyurethane hydrogel including 10 mol% of glycerol presents a large swelling ratio change between 4 °C and 37 °C from 250% to 40%. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis, Characterization and in Vitro Evaluation of New Composite Bisphosphonate Delivery Systems

PubMed Central

Kolmas, Joanna; Sobczak, Marcin; Olędzka, Ewa; Nałęcz-Jawecki, Grzegorz; Dębek, Cezary

2014-01-01

In this study, new composite bisphosphonate delivery systems were obtained from polyurethanes (PUs) and nanocrystalline hydroxyapatite (HA). The biodegradable PUs were first synthesized from poly(ε-caprolactone) diols (PCL diols), poly(ethylene adipate) diol, 1,6-hexamethylene diisocyanate, 1,4-butanediol and HA. Moreover, the PCL diols were synthesized by the ring-opening polymerization catalysed by the lipase from Candida antarctica. Next, composite drug delivery systems for clodronate were prepared. The mechanical properties of the obtained biomaterials were determined. The cytotoxicity of the synthesized polymers was tested. The preliminary results show that the obtained composites are perspective biomaterials and they can be potentially applied in the technology of implantation drug delivery systems. PMID:25247580

Effect of phorbol esters on the macrophage-mediated biodegradation of polyurethanes via protein kinase C activation and other pathways.

PubMed

McBane, Joanne Eileen; Santerre, J P; Labow, Rosalind

2009-01-01

It was previously found that re-seeding monocyte-derived macrophages (MDM) on polycarbonate-based polyurethanes (PCNUs) in the presence of the protein kinase C (PKC) activator phorbol myristate acetate (PMA) inhibited MDM-mediated degradation of PCNUs synthesized with 1,6-hexane diisocyanate (HDI), as well as esterase activity and monocyte-specific esterase (MSE) protein. However, no effect on the degradation of a 4,4'-methylene bisphenyl (MDI)-derived PCNU (MDI321) occurred. This finding suggested that oxidation, a process linked to the PKC pathway, was not activated in the same manner for all PCNUs. In the current study MDM were re-seeded onto the above PCNU surfaces with PMA, PKC-inactive 4alphaPMA and the PKC inhibitor bisindolylmaleimide I hydrochloride (BIM) for 48 h before assaying for PCNU degradation, esterase activity, MSE protein, DNA, cell viability and cell morphology. 4alphaPMA did not alter MDM-mediated HDI PCNU degradation but MDI321 degradation increased in this condition. BIM alone had no effect on any parameter; however, when BIM and PMA were added together, the PMA inhibition of biodegradation, esterase activity and MSE protein was partially reversed for MDM on HDI PCNUs only. Adding PMA to MDM on HDI PCNUs increased intercellular connections, whereas 4alphaPMA or BIM+PMA increased cell size. Although this study demonstrated a role for oxidation via a PKC-activated pathway in MDM-mediated PCNU degradation, phorbol esters appear to also activate non-PKC pathways that have roles in biodegradation. Moreover, the sensitivity to material surface chemistry in the MDM response to each PCNU dictates a multi-factorial degradative process involving alternate material specific oxidative and hydrolytic mechanisms.

New biobased high functionality polyols and their use in polyurethane coatings.

PubMed

Pan, Xiao; Webster, Dean C

2012-02-13

High-functionality polyols for application in polyurethanes (PUs) were prepared by epoxide ring-opening reactions from epoxidized sucrose esters of soybean oil-epoxidized sucrose soyates-in which secondary hydroxyl groups were generated from epoxides on fatty acid chains. Ester polyols were prepared by using a base-catalyzed acid-epoxy reaction with carboxylic acids (e.g., acetic acid); ether polyols were prepared by using an acid-catalyzed alcohol-epoxy reaction with monoalcohols (e.g., methanol). The polyols were characterized by using gel permeation chromatography, FTIR spectroscopy, (1)H NMR spectroscopy, differential scanning calorimetry (DSC), and viscosity measurements. PU thermosets were prepared by using aliphatic polyisocyanates based on isophorone diisocyanate and hexamethylene diisocyanate. The properties of the PUs were studied by performing tensile testing, dynamic mechanical analysis, DSC, and thermogravimetric analysis. The properties of PU coatings on steel substrates were evaluated by using ASTM methods to determine coating hardness, adhesion, solvent resistance, and ductility. Compared to a soy triglyceride polyol, sucrose soyate polyols provide greater hardness and range of cross-link density to PU thermosets because of the unique structure of these macromolecules: well-defined compact structures with a rigid sucrose core coupled with high hydroxyl group functionality. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Application of high-strength biodegradable polyurethanes containing different ratios of biobased isomannide and poly (ϵ-caprolactone) diol

PubMed Central

Lim, Dong-In; Park, Hyung-Seok; Park, Jeong-Hui; Knowles, Jonathan C

2013-01-01

Biodegradable–biocompatible polyurethanes were prepared with fixed hexamethylene diisocyanate and varying ratios of isomannide and poly(ϵ-caprolactone) diol using a simple one-step polymerization without a catalyst. The polyurethane structures were confirmed by 1H-nuclear magnetic resonance, Fourier transform infrared spectroscopy, and gel permeation chromatography. The glass transition temperatures were determined by thermal analysis to be between 25°C and 30°C. Degradation tests performed at 37°C in phosphate buffer produced mass losses of 5%–10% after 8 weeks. After 5 days of culture, using osteoblastic cells, the relative cell number on all the polyurethane films was only slightly lower than that of an optimized tissue culture plastic. These polymers offer significant promise with a simplistic synthesis and controlled degradation. PMID:25076809

Control of Mechanical Properties of Thermoplastic Polyurethane Elastomers by Restriction of Crystallization of Soft Segment

PubMed Central

Kojio, Ken; Furukawa, Mutsuhisa; Nonaka, Yoshiteru; Nakamura, Sadaharu

2010-01-01

Mechanical properties of thermoplastic polyurethane elastomers based on either polyether or polycarbonate (PC)-glycols, 4,4’-dipheylmethane diisocyanate (1,1’-methylenebis(4-isocyanatobenzene)), 1,4-butanediol, were controlled by restriction of crystallization of polymer glycols. For the polyether glycol based-polyurethane elastomers (PUEs), poly(oxytetramethylene) glycol (PTMG), and PTMG incorporating dimethyl groups (PTG-X) and methyl side groups (PTG-L) were employed as a polymer glycol. For the PC-glycol, the randomly copolymerized PC-glycols with hexamethylene (C6) and tetramethylene (C4) units between carbonate groups with various composition ratios (C4/C6 = 0/100, 50/50, 70/30 and 90/10) were employed. The degree of microphase separation and mechanical properties of both the PUEs were investigated using differential scanning calorimetry, dynamic viscoelastic property measurements and tensile testing. Mechanical properties could be controlled by changing the molar ratio of two different monomer components. PMID:28883371

Hexavalent chromium and isocyanate exposures during military aircraft painting under crossflow ventilation.

PubMed

Bennett, James S; Marlow, David A; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers ("hosemen"). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group--the total of monomer and oligomer as NCO group mass--showed 6 of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re-circulations, turbulence, and fugitive emissions, while wasting energy. Smoke releases showing more effective ventilation here than in other aircraft painting facilities carries technical feasibility relevance.

Hexavalent Chromium and Isocyanate Exposures during Military Aircraft Painting under Crossflow Ventilation

PubMed Central

Bennett, James S.; Marlow, David A.; Nourian, Fariba; Breay, James; Hammond, Duane

2016-01-01

Exposure control systems performance was investigated in an aircraft painting hangar. The ability of the ventilation system and respiratory protection program to limit worker exposures was examined through air sampling during painting of F/A-18C/D strike fighter aircraft, in four field surveys. Air velocities were measured across the supply filter, exhaust filter, and hangar midplane under crossflow ventilation. Air sampling conducted during painting process phases (wipe-down, primer spraying, and topcoat spraying) encompassed volatile organic compounds, total particulate matter, Cr[VI], metals, nitroethane, and hexamethylene diisocyanate, for two worker groups: sprayers and sprayer helpers (“hosemen”). One of six methyl ethyl ketone and two of six methyl isobutyl ketone samples exceeded the short term exposure limits of 300 and 75 ppm, with means 57 ppm and 63 ppm, respectively. All 12 Cr[VI] 8-hr time-weighted averages exceeded the recommended exposure limit of 1 µg/m3, 11 out of 12 exceeded the permissible exposure limit of 5 µg/m3, and 7 out of 12 exceeded the threshold limit value of 10 µg/m3, with means 38 µg/m3 for sprayers and 8.3 µg/m3 for hosemen. Hexamethylene diisocyanate means were 5.95 µg/m3 for sprayers and 0.645 µg/m3 for hosemen. Total reactive isocyanate group—the total of monomer and oligomer as NCO group mass—showed six of 15 personal samples exceeded the United Kingdom Health and Safety Executive workplace exposure limit of 20 µg/m3, with means 50.9 µg/m3 for sprayers and 7.29 µg/m3 for hosemen. Several exposure limits were exceeded, reinforcing continued use of personal protective equipment. The supply rate, 94.4 m3/s (200,000 cfm), produced a velocity of 8.58 m/s (157 fpm) at the supply filter, while the exhaust rate, 68.7 m3/s (146,000 cfm), drew 1.34 m/s (264 fpm) at the exhaust filter. Midway between supply and exhaust locations, the velocity was 0.528 m/s (104 fpm). Supply rate exceeding exhaust rate created re-circulations, turbulence, and fugitive emissions, while wasting energy. Smoke releases showing more effective ventilation here than in other aircraft painting facilities carries technical feasibility relevance. PMID:26698920

Biodegradable block poly(ester-urethane)s based on poly(3-hydroxybutyrate-co-4-hydroxybutyrate) copolymers.

PubMed

Ou, Wenfeng; Qiu, Handi; Chen, Zhifei; Xu, Kaitian

2011-04-01

A series of block poly(ester-urethane)s (abbreviated as PU3/4HB) based on biodegradable poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P3/4HB) segments were synthesized by a facile way of melting polymerization using 1,6-hexamethylene diisocyanate (HDI) as the coupling agent and stannous octanoate (Sn(Oct)(2)) as catalyst, with different 4HB contents and segment lengths. The chemical structure, molecular weight and distribution were systematically characterized by (1)H nuclear magnetic resonance spectrum (NMR), Fourier transform infrared spectroscopy (FTIR) and gel permeation chromatography (GPC). The thermal property was studied by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The hydrophilicity was investigated by static contact angle of deionized water and CH(2)I(2). DSC curves revealed that the PU3/4HB polyurethanes have their T(g) from -25.6 °C to -4.3 °C, and crystallinity from 2.5% to 25.3%, being almost amorphous to semi-crystalline. The obtained PU3/4HBs are hydrophobic (water contact angle 77.4°-95.9°), and their surface free energy (SFE) were studied. The morphology of platelets adhered on the polyurethane film observed by scanning electron microscope (SEM) showed that platelets were activated on the PU3/4HB films which would lead to blood coagulation. The lactate dehydrogenase (LDH) assay revealed that the PU3/4HBs displayed higher platelet adhesion property than raw materials and biodegradable polymer polylactic acid (PLA) and would be potential hemostatic materials. Crystallinity degree, hydrophobicity, surface free energy and urethane linkage content play important roles in affecting the LDH activity and hence the platelet adhesion. CCK-8 assay showed that the PU3/4HB is non-toxic and well for cell growth and proliferation of mouse fibroblast L929. It showed that the hydrophobicity is an important factor for cell growth while 3HB content of the PU3/4HB is important for the cell proliferation. Through changing the composition and the chain-length of P3/4HB-diol prepolymers, the biocompatibility of the poly(ester-urethane)s can be tailored. Copyright © 2011 Elsevier Ltd. All rights reserved.

Hydrogels of poly(ethylene glycol): mechanical characterization and release of a model drug.

PubMed

Iza, M; Stoianovici, G; Viora, L; Grossiord, J L; Couarraze, G

1998-03-02

Thermosensitive polymer networks were synthesized from poly(ethylene glycol), hexamethylene diisocyanate and 1,2,6-hexanetriol in stoichiometric proportions. By varying the amount of 1,2,6-hexanetriol and the molar mass of the poly(ethylene glycol), a wide range of networks with different crosslinking densities was prepared. The networks obtained were characterized by the temperature dependence of their degree of equilibrium swelling in water and by their Young's moduli. For each network, the molecular weight between crosslinks was estimated. The structure of the hydrogels was analysed with respect to scaling laws, and it was found that the results obtained with PEG 1500 and PEG 6000 hydrogels are in agreement with theoretical predictions, whereas those obtained with PEG 400 hydrogels are in disagreement. The release properties of PEG hydrogels were studied by the determination of the diffusion coefficient for acebutolol chlorhydrate and by an analysis of the effect of temperature on these coefficients. Finally, these release properties were correlated with the swelling and structural properties of the hydrogels.

Facile preparation of mussel-inspired polyurethane hydrogel and its rapid curing behavior.

PubMed

Sun, Peiyu; Wang, Jing; Yao, Xiong; Peng, Ying; Tu, Xiaoxiong; Du, Pengfei; Zheng, Zhen; Wang, Xinling

2014-08-13

A facile method was found to incorporate a mussel-inspired adhesive moiety into synthetic polymers, and mussel mimetic polyurethanes were developed as adhesive hydrogels. In these polymers, a urethane backbone was substituted for the polyamide chain of mussel adhesive proteins, and dopamine was appended to mimic the adhesive moiety of adhesive proteins. A series of mussel mimetic polyurethanes were created through a step-growth polymerization based on hexamethylene diisocyanate as a hard segment, PEG having different molecular weights as a soft segment, and lysine-dopamine as a chain extender. Upon a treatment with Fe(3+), the aqueous mussel mimetic polyurethane solutions can be triggered by pH adjustment to form adhesive hydrogels instantaneously; these materials can be used as injectable adhesive hydrogels. Upon a treatment with NaIO4, the mussel mimetic polyurethane solutions can be cured in a controllable period of time. The successful combination of the unique mussel-inspired adhesive moiety with a tunable polyurethane structure can result in a new kind of mussel-inspired adhesive polymers.

Facile preparation of antibacterial, highly elastic silvered polyurethane nanofiber fabrics using silver carbamate and their dermal wound healing properties.

PubMed

Hong, Suk-Min; Kim, Jong-Wan; Knowles, Jonathan C; Gong, Myoung-Seon

2017-02-01

In this study, polycarbonate diol/isosorbide-based antibacterial polyurethane nanofiber fabrics containing Ag nanoparticles were prepared by electrospinning process. Bio-based highly elastic polyurethane was prepared from hexamethylene diisocyanate and isosorbide/polycarbonate diol (8/2) by a simple one-shot bulk polymerization. Ag nanoparticles were formed using simple thermal reduction of silver 2-ethylhexylcarbamate at 120℃. The structural and morphological properties of polyurethane/Ag nanofibers were characterized by X-ray diffraction and scanning electron microscopy. The polyurethane nanofiber fabrics were flexible, with breaking strains from 355% to 950% under 7.28 to 23.1 MPa tensile stress. The antibacterial effects of the treated polyurethane/Ag fabrics against Staphylococcus aureus and methicillin resistant Staphylococcus aureus were examined and found to be excellent. Cell proliferation using the immortalized human keratinocyte HaCaT cell line was performed in order to determine cell viability in the presence of polyurethane and polyurethane/Ag fabrics, showing cytocompatiblility and a lack of toxicity.

Evaluation on biocompatibility of biomedical polyurethanes with different hard segment contents

NASA Astrophysics Data System (ADS)

Ma, Dai-Wei; Zhu, Rong; Wang, Yi-Yu; Zhang, Zong-Rui; Wang, Xin-Yu

2015-12-01

In this paper, polyurethane (PU) materials with different contents of hard segment (20%, 25%, 30%) were prepared based on hexamethylene diisocyanate and polycarbonate diols by solution polymerization. The obtained polycarbonate-urethane (PCU) elastomers were characterized by very good hydrophobic property and excellent resistance to hydrolysis. Hemolysis, recalification time and platelet-rich plasma adhesion were used to evaluate the blood compatibility of the materials. L929 cells cultured with leach liquor of these PU membranes were selected to perform the cytotoxicity experiments. The results indicate that the hemolysis rates of PU membranes are all less than 5%, which can meet the requirement of the national standards for biomaterials. However, compared with 20% and 30% groups, the recalification time of the sample containing 25% hard segment is longer, while the number of platelet adhesion is less. Additionally, cells cultured in the leach liquor of PU membranes with 25% hard segment proliferated relatively more thriving, meaning that this proportion of the material has the lowest cytotoxicity.

Synthesis and Anticoagulant Activity of Polyureas Containing Sulfated Carbohydrates

PubMed Central

2015-01-01

Polyurea-based synthetic glycopolymers containing sulfated glucose, mannose, glucosamine, or lactose as pendant groups have been synthesized by step-growth polymerization of hexamethylene diisocyanate and corresponding secondary diamines. The obtained polymers were characterized by gel permeation chromatography, nuclear magnetic resonance spectroscopy, and Fourier transform infrared spectroscopy. The nonsulfated polymers showed similar results to the commercially available biomaterial polyurethane TECOFLEX in a platelet adhesion assay. The average degree of sulfation after reaction with SO3 was calculated from elemental analysis and found to be between three and four −OSO3 groups per saccharide. The blood-compatibility of the synthetic polymers was measured using activated partial thromboplastin time, prothrombin time, thrombin time, anti-IIa, and anti-Xa assays. Activated partial thromboplastin time, prothrombin time, and thrombin time results indicated that the mannose and lactose based polymers had the highest anticoagulant activities among all the sulfated polymers. The mechanism of action of the polymers appears to be mediated via an anti-IIa pathway rather than an anti-Xa pathway. PMID:25329742

Manufacturing of biodegradable polyurethane scaffolds based on polycaprolactone using a phase separation method: physical properties and in vitro assay

PubMed Central

Asefnejad, Azadeh; Khorasani, Mohammad Taghi; Behnamghader, Aliasghar; Farsadzadeh, Babak; Bonakdar, Shahin

2011-01-01

Background Biodegradable polyurethanes have found widespread use in soft tissue engineering due to their suitable mechanical properties and biocompatibility. Methods In this study, polyurethane samples were synthesized from polycaprolactone, hexamethylene diisocyanate, and a copolymer of 1,4-butanediol as a chain extender. Polyurethane scaffolds were fabricated by a combination of liquid–liquid phase separation and salt leaching techniques. The effect of the NCO:OH ratio on porosity content and pore morphology was investigated. Results Scanning electron micrographs demonstrated that the scaffolds had a regular distribution of interconnected pores, with pore diameters of 50–300 μm, and porosities of 64%–83%. It was observed that, by increasing the NCO:OH ratio, the average pore size, compressive strength, and compressive modulus increased. L929 fibroblast and chondrocytes were cultured on the scaffolds, and all samples exhibited suitable cell attachment and growth, with a high level of biocompatibility. Conclusion These biodegradable polyurethane scaffolds demonstrate potential for soft tissue engineering applications. PMID:22072874

Determinants of isocyanate exposures in auto body repair and refinishing shops.

PubMed

Woskie, S R; Sparer, J; Gore, R J; Stowe, M; Bello, D; Liu, Y; Youngs, F; Redlich, C; Eisen, E; Cullen, M

2004-07-01

As part of the Survey of Painters and Repairers of Auto bodies by Yale (SPRAY), the determinants of isocyanate exposure in auto body repair shops were evaluated. Measurements (n = 380) of hexamethylene diisocyanate-based monomer and polyisocyanate and isophorone diisocyanate-based polyisocyanate were collected from 33 auto body shops. The median total reactive isocyanate concentrations expressed as mass concentration of the NCO functional group were: 206 microg NCO/m3 for spray operations; 0.93 microg NCO/m3 for samples collected in the vicinity of spray operations done on the shop floor (near spray); 0.05 microg NCO/m3 for office or other shop areas adjacent to spray areas (workplace background); 0.17 microg NCO/m3 for paint mixing and gun cleaning operations (mixing); 0.27 microg NCO/m3 for sanding operations. Exposure determinants for the sample NCO mass load were identified using linear regression, tobit regression and logistic regression models. For spray samples in a spray booth the significant determinants were the number of milliliters of NCO applied, the gallons of clear coat used by the shop each month and the type of spray booth used (custom built crossdraft, prefabricated crossdraft or downdraft/semi-downdraft). For near spray (bystander) samples, outdoor temperature >65 degrees F (18 degrees C) and shop size >5000 feet2 (465 m2) were significant determinants of exposure levels. For workplace background samples the shop annual income was the most important determinant. For sanding samples, the shop annual income and outdoor temperature >65 degrees F (18 degrees C) were the most significant determinants. Identification of these key exposure determinants will be useful in targeting exposure evaluation and control efforts to reduce isocyanate exposures.

Polycarbonate-based polyurethane as a polymer electrolyte matrix for all-solid-state lithium batteries

NASA Astrophysics Data System (ADS)

Bao, Junjie; Shi, Gaojian; Tao, Can; Wang, Chao; Zhu, Chen; Cheng, Liang; Qian, Gang; Chen, Chunhua

2018-06-01

Four kinds of polycarbonate-based polyurethane with 8-14 wt% hard segments content are synthesized via reactions of polycarbonatediol, hexamethylene diisocyanate and diethylene glycol. The mechanical strength of the polyurethanes increase with the increase of hard segments content. Solid polymer electrolytes composed of the polycarbonate-based polyurethanes and LiTFSI exhibits fascinating characteristics for all-solid-state lithium batteries with a high ionic conductivity of 1.12 × 10-4 S cm-1 at 80 °C, an electrochemical stability window up to 4.5 V (vs. Li+/Li), excellent mechanical strength and superior interfacial stability against lithium metal. The all-solid-state batteries using LiFePO4 cathode can deliver high discharge capacities (161, 158, 134 and 93 mAh g-1 at varied rates of 0.2, 0.5, 1 and 2 C) at 80 °C and excellent cycling performance (with 91% capacity retention after 600 cycles at 1 C). All the results indicate that such a polyurethane-based solid polymer electrolyte can be a promising candidate for all-solid-state lithium batteries.

A water-soluble, mucoadhesive quaternary ammonium chitosan-methyl-β-cyclodextrin conjugate forming inclusion complexes with dexamethasone.

PubMed

Piras, Anna Maria; Zambito, Ylenia; Burgalassi, Susi; Monti, Daniela; Tampucci, Silvia; Terreni, Eleonora; Fabiano, Angela; Balzano, Federica; Uccello-Barretta, Gloria; Chetoni, Patrizia

2018-03-30

The ocular bioavailability of lipophilic drugs, such as dexamethasone, depends on both drug water solubility and mucoadhesion/permeation. Cyclodextrins and chitosan are frequently employed to either improve drug solubility or prolong drug contact onto mucosae, respectively. Although the covalent conjugation of cyclodextrin and chitosan brings to mucoadhesive drug complexes, their water solubility is restricted to acidic pHs. This paper describes a straightforward grafting of methyl-β-cyclodextrin (MCD) on quaternary ammonium chitosan (QA-Ch60), mediated by hexamethylene diisocyanate. The resulting product is a water-soluble chitosan derivative, having a 10-atom long spacer between the quaternized chitosan and the cyclodextrin. The derivative is capable of complexing the model drug dexamethasone and stable complexes were also observed for the lyophilized products. Furthermore, the conjugate preserves the mucoadhesive properties typical of quaternized chitosan and its safety as solubilizing excipient for ophthalmic applications was preliminary assessed by in vitro cytotoxicity evaluations. Taken as a whole, the observed features appear promising for future processing of the developed product into 3D solid forms, such as controlled drug delivery systems, films or drug eluting medical devices.

Synthesis and characterization of chitosan/curcumin blends based polyurethanes.

PubMed

Zia, Fatima; Zia, Khalid Mahmood; Zuber, Mohammad; Rehman, Saima; Tabasum, Shazia; Sultana, Salma

2016-11-01

In this work, new hexamethylene diisocyanate (HMDI) and hyroxylterminated polybutadiene (HTPB) based polyurethanes (PUs) were prepared following step growth polymerization by the introduction of varying mole ratio of chitosan (CH) and curcumin (CUR). Structural study of blends through infrared spectroscopy confirmed the incorporation of CH and CUR into the backbone of the PU. The scanning electron microscopic (SEM) study confirmed the well dispersion of incorporated chitosan/curcumin and homogeneity of surface of synthesized samples. Thermogravimetric analysis (TGA) of PU blends indicated a better thermal stability with 0.25M:0.75M of chitosan to curcumin. Mechanical properties such as modulus and tensile strength of PU blends were found to be better with higher contents of chitosan and curcumin. The same extender composition (1mol BDO, 075mol chitosan and 0.25mol curcumin) based PU showed higher substantial of antimicrobial activity as compared to the all other PUs. On the whole, this work is actually a step towards the generation of novel biocompatible materials preferably useful for biomedical applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Artificial extracellular matrix for biomedical applications: biocompatible and biodegradable poly (tetramethylene ether) glycol/poly (ε-caprolactone diol)-based polyurethanes.

PubMed

Shahrousvand, Mohsen; Mir Mohamad Sadeghi, Gity; Salimi, Ali

2016-12-01

The cells as a tissue component need to viscoelastic, biocompatible, biodegradable, and wettable extracellular matrix for their biological activity. In this study, in order to prepare biomedical polyurethane elastomers with good mechanical behavior and biodegradability, a series of novel polyester-polyether- based polyurethanes (PUs) were synthesized using a two-step bulk reaction by melting pre-polymer method, taking 1,4-Butanediol (BDO) as chain extender, hexamethylene diisocyanate as the hard segment, and poly (tetramethylene ether) glycol (PTMEG) and poly (ε-caprolactone diol) (PCL-Diol) as the soft segment without a catalyst. The soft to the hard segment ratio was kept constant in all samples. Polyurethane characteristics such as thermal and mechanical properties, wettability and water adsorption, biodegradability, and cellular behavior were changed by changing the ratio of polyether diol to polyester diol composition in the soft segment. Our present work provides a new procedure for the preparation of engineered polyurethanes in surface properties and biodegradability, which could be a good candidate for bone, cartilage, and skin tissue engineering.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hoffman, D.M.; Jessop, E.S.; Swansiger, R.W.

Cast cure, extrusion cast, and paste extrudable explosives have not been designed for transferring through long tortuous paths or into fine three dimensional shapes. To allow the crystalline explosive to flow a lubricating fluid is required. The energetic liquid ethane trinitrate (TMETN) was used as the lubricant to maximize the explosive energy. TMETN is a liquid nitrate ester which requires stabilization with conventional free radical stabilizers such as 2- nitrodiphenylamine, methyl-nitroanaline, or ethyl centrylite. Since these injection moldable explosives are expected to cure in place, a polyesterurethane binder based on polymeric isocyanate of hexamethylene diisocyanate and polycaprolactone polyols is dissolvedmore » in TMETN. The solubility of the polymer precursors in TMETN also reduces the energetic liquids sensitivity. The latent cure catalyst Dabco T-131 was used to minimize shrinkage associated with thermal expansion, reduce cost associated with oven cures, to give 4-6 hour potlife and overnight cure to handling strength. The product RX-08-HD is a new, low-viscosity, injection moldable explosive that can be extruded into complex, void-free shapes. Combined with appropriate design and other aspects of weaponization, RX-08-HD has produced outstanding results.« less

Polyurethane/fluor-hydroxyapatite nanocomposite scaffolds for bone tissue engineering. Part I: morphological, physical, and mechanical characterization

PubMed Central

Asefnejad, Azadeh; Behnamghader, Aliasghar; Khorasani, Mohammad Taghi; Farsadzadeh, Babak

2011-01-01

In this study, new nano-fluor-hydroxyapatite (nFHA)/polyurethane composite scaffolds were fabricated for potential use in bone tissue engineering. Polyester urethane samples were synthesized from polycaprolactone, hexamethylene diisocyanate, and 1,4-butanediol as chain extender. Nano fluor-hydroxyapatite (nFHA) was successfully synthesized by sol-gel method. The solid–liquid phase separation and solvent sublimation methods were used for preparation of the porous composites. Mechanical properties, chemical structure, and morphological characteristics of the samples were investigated by compressive test, Fourier transform infrared, and scanning electron microscopy (SEM) techniques, respectively. The effect of nFHA powder content on porosity and pore morphology was investigated. SEM images demonstrated that the scaffolds were constituted of interconnected and homogeneously distributed pores. The pore size of the scaffolds was in the range 50–250 μm. The result obtained in this research revealed that the porosity and pore average size decreased and compressive modulus increased with nFHA percentage. Considering morphological, physical, and mechanical properties, the scaffold with a higher ratio of nFHA has suitable potential use in tissue regeneration. PMID:21289986

Effect of ventilation velocity on hexavalent chromium and isocyanate exposures in aircraft paint spraying.

PubMed

Bennett, James; Marlow, David; Nourian, Fariba; Breay, James; Feng, Amy; Methner, Mark

2018-03-01

Exposure control system performance was evaluated during aircraft paint spraying at a military facility. Computational fluid dynamics (CFD) modeling, tracer gas testing, and exposure monitoring examined contaminant exposure vs. crossflow ventilation velocity. CFD modeling using the RNG k-ϵ turbulence model showed exposures to simulated methyl isobutyl ketone of 294 and 83.6 ppm, as a spatial average of five worker locations, for velocities of 0.508 and 0.381 m/s (100 and 75 fpm), respectively. In tracer gas experiments, observed supply/exhaust velocities of 0.706/0.503 m/s (136/99 fpm) were termed full-flow, and reduced velocities were termed 3/4-flow and half-flow. Half-flow showed higher tracer gas concentrations than 3/4-flow, which had the lowest time-averaged concentration, with difference in log means significant at the 95% confidence level. Half-flow compared to full-flow and 3/4-flow compared to full-flow showed no statistically significant difference. CFD modeling using these ventilation conditions agreed closely with the tracer results for the full-flow and 3/4-flow comparison, yet not for the 3/4-flow and half-flow comparison. Full-flow conditions at the painting facility produced a velocity of 0.528 m/s (104 fpm) midway between supply and exhaust locations, with the supply rate of 94.4 m 3 /s (200,000 cfm) exceeding the exhaust rate of 68.7 m 3 /s (146,000 cfm). Ventilation modifications to correct this imbalance created a midhangar velocity of 0.406 m/s (80.0 fpm). Personal exposure monitoring for two worker groups-sprayers and sprayer helpers ("hosemen")-compared process duration means for the two velocities. Hexavalent chromium (Cr[VI]) exposures were 500 vs. 360 µg/m 3 for sprayers and 120 vs. 170 µg/m 3 for hosemen, for 0.528 m/s (104 fpm) and 0.406 m/s (80.0 fpm), respectively. Hexamethylene diisocyanate (HDI) monomer means were 32.2 vs. 13.3 µg/m 3 for sprayers and 3.99 vs. 8.42 µg/m 3 for hosemen. Crossflow velocities affected exposures inconsistently, and local work zone velocities were much lower. Aircraft painting contaminant control is accomplished better with the unidirectional crossflow ventilation presented here than with other observed configurations. Exposure limit exceedances for this ideal condition reinforce continued use of personal protective equipment.

Fe-Ni Nanoparticles supported on carbon nanotube-co-cyclodextrin polyurethanes for the removal of trichloroethylene in water

NASA Astrophysics Data System (ADS)

Krause, Rui W. M.; Mamba, Bhekie B.; Dlamini, Langelihle N.; Durbach, Shane H.

2010-02-01

Nanoscale bimetallic particles of nickel on iron were supported on carbon nanotubes and then co-polymerized with β-cyclodextrin (CNTs/CD) and the resulting polymers applied to the degradation of pollutants in water. The bimetallic nanoparticles (BMNPs) were first embedded on functionalized carbon nanotubes (f-CNTs) before being copolymerized with beta cyclodextrin (β-CD) and hexamethylene diisocyanate (HMDI) forming a water-insoluble polyurethane. The particle size and distribution of BMNPs were determined by Transmission Electron Microscopy (TEM), and the surface area was determined by using the Brunauer-Emmett-Teller (BET) method. Energy dispersive X-ray spectroscopy (EDXS) was used to confirm the formation of the BMNPs. Degradation of trichloroethylene (TCE) as a model pollutant was studied and more than 98% reduction in TCE was achieved by the polymers. Polymers with the BMNPs maintained their efficiency in degrading TCE after several cycles compared to metal-free polymers. The degradation was monitored by using gas chromatography-mass spectrometry (GC-MS), while the production of chlorides was verified by using ion chromatography (IC). Atomic absorption spectroscopy (AAS) was employed to determine the possible leaching of the BMNPs from the polymer, and confirmed to be extremely low.

Effects of the Acrylic Polyol Structure and the Selectivity of the Employed Catalyst on the Performance of Two-Component Aqueous Polyurethane Coatings

PubMed Central

Cakic, Suzana; Lacnjevac, Caslav; Stamenkovic, Jakov; Ristic, Nikola; Takic, Ljiljana; Barac, Miroljub; Gligoric, Miladin

2007-01-01

Two kinds of aqueous acrylic polyols (single step and multi step synthesis type) have been investigated for their performance in the two-component aqueous polyurethane application, by using more selective catalysts. The aliphatic polyfunctional isocyanates based on hexamethylen diisocyanates have been employed as suitable hardeners. The complex of zirconium, commercially known as K-KAT®XC-6212, and manganese (III) complexes with mixed ligands based on the derivative of maleic acid have been used as catalysts in this study. Both of the aqueous polyols give good results, in terms of application and hardness, when elevated temperatures and more selective catalysts are applied. A more selective catalyst promotes the reaction between the isocyanate and polyol component. This increases the percentage of urethane bonds and the degree of hardness in the films formed from the two components of aqueous polyurethane lacquers. The polyol based on the single step synthesis route is favourable concerning potlife and hardness. The obtained results show that the performance of the two-component aqueous polyurethane coatings depends on the polymer structure of the polyols as well as on the selectivity of the employed catalyst.

Synthesis of highly elastic biocompatible polyurethanes based on bio-based isosorbide and poly(tetramethylene glycol) and their properties

PubMed Central

Kim, Hyo-Jin; Kang, Min-Sil; Knowles, Jonathan C

2014-01-01

Bio-based high elastic polyurethanes were prepared from hexamethylene diisocyanate and various ratios of isosorbide to poly(tetramethylene glycol) as a diol by a simple one-shot bulk polymerization without a catalyst. Successful synthesis of the polyurethanes was confirmed by Fourier transform-infrared spectroscopy and 1H nuclear magnetic resonance. Thermal properties were determined by differential scanning calorimetry and thermogravimetric analysis. The glass transition temperature was −47.8℃. The test results showed that the poly(tetramethylene glycol)/isosorbide-based elastomer exhibited not only excellent stress–strain properties but also superior resilience to the existing polyether-based polyurethane elastomers. The static and dynamic properties of the polyether/isosorbide-based thermoplastic elastomer were more suitable for dynamic applications. Moreover, such rigid diols impart biocompatible and bioactive properties to thermoplastic polyurethane elastomers. Degradation tests performed at 37℃ in phosphate buffer solution showed a mass loss of 4–9% after 8 weeks, except for the polyurethane with the lowest isosorbide content, which showed an initial rapid weight loss. These polyurethanes offer significant promise due to soft, flexible and biocompatible properties for soft tissue augmentation and regeneration. PMID:24812276

α-Amylase sensor based on the degradation of oligosaccharide hydrogel films monitored with a quartz crystal sensor.

PubMed

Gibbs, Martin John; Biela, Anna; Krause, Steffi

2015-05-15

α-Amylase hydrolyses starch molecules to produce smaller oligosaccharides and sugars. Amylases are of great importance in biotechnology and find application in fermentation, detergents, food and the paper industry. The measurement of α-amylase activity in serum and urine has been used in the diagnosis of acute pancreatitis. Salivary amylase has also been shown to be a stress indicator. Sensor coatings suitable for the detection of α-amylase activity have been developed. Oligosaccharides such as glycogen and amylopectin were spin-coated onto gold coated quartz crystals with a base frequency of 10 MHz. The films were subsequently cross-linked with hexamethylene diisocyanate. Film degradation was monitored with a quartz crystal microbalance (QCM) and electrochemical impedance measurements. The films were shown to be stable in phosphate buffered saline (PBS). Addition of α-amylase to the solution resulted in the rapid degradation of the films. The maximum rate of degradation was found to be strongly dependent on the amylase activity in the range typically found in serum when diagnosing pancreatitis (0.08-8 U/ml). Sensor responses in serum were found to be very similar to those obtained in buffer indicating the absence of non-specific binding. Copyright © 2014 Elsevier B.V. All rights reserved.

Glutathione-mediated biodegradable polyurethanes derived from L-arabinitol.

PubMed

de Paz, M Violante; Zamora, Francisca; Begines, Belén; Ferris, Cristina; Galbis, Juan A

2010-01-11

The synthesis, characterization, and some properties of new glutathione-mediated biodegradable sugar-based copolyurethanes are described. These copolyurethanes were obtained by polyaddition reaction of mixtures of 2,2'-dithiodiethanol (DiT) and 2,3,4-tri-O-benzyl-L-arabinitol (ArBn) or 2,3,4-tri-O-methyl-L-arabinitol (ArMe) to 1,6-hexamethylene diisocyanate (HMDI). The copolymer compositions were studied by elemental microanalyses and (1)H NMR, revealing that the content of the copolymer units is in all cases very similar to that of their corresponding feed. The PU(DiT-HMDI) homopolymer exhibited a high crystallinity, but the introduction of the arabinitol-based diols led to a reduction in the crystallinity of the copolymers. In their TG curves, the copolymers exhibited a mixed trend of the related homopolymers, and all of them were thermally stable, with degradation temperatures above 220 degrees C. The degradation properties of the macromolecules under physiological conditions in the presence of glutathione were tested. All the copolyurethanes proved to be biodegradable under the experimental conditions (pH = 7.02 and 37 degrees C). The degradation pattern of the copolymers depended not only on the dithiodiethanol (DiT) reactive units ratio in the polymer backbone, but also on the crystallinity of the macromolecule.

Synthesis of highly elastic biocompatible polyurethanes based on bio-based isosorbide and poly(tetramethylene glycol) and their properties.

PubMed

Kim, Hyo-Jin; Kang, Min-Sil; Knowles, Jonathan C; Gong, Myoung-Seon

2014-09-01

Bio-based high elastic polyurethanes were prepared from hexamethylene diisocyanate and various ratios of isosorbide to poly(tetramethylene glycol) as a diol by a simple one-shot bulk polymerization without a catalyst. Successful synthesis of the polyurethanes was confirmed by Fourier transform-infrared spectroscopy and (1)H nuclear magnetic resonance. Thermal properties were determined by differential scanning calorimetry and thermogravimetric analysis. The glass transition temperature was -47.8℃. The test results showed that the poly(tetramethylene glycol)/isosorbide-based elastomer exhibited not only excellent stress-strain properties but also superior resilience to the existing polyether-based polyurethane elastomers. The static and dynamic properties of the polyether/isosorbide-based thermoplastic elastomer were more suitable for dynamic applications. Moreover, such rigid diols impart biocompatible and bioactive properties to thermoplastic polyurethane elastomers. Degradation tests performed at 37℃ in phosphate buffer solution showed a mass loss of 4-9% after 8 weeks, except for the polyurethane with the lowest isosorbide content, which showed an initial rapid weight loss. These polyurethanes offer significant promise due to soft, flexible and biocompatible properties for soft tissue augmentation and regeneration. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Impact of Human Development Index on the profile and outcomes of patients with acute coronary syndrome.

PubMed

Roy, Ambuj; Roe, Matthew T; Neely, Megan L; Cyr, Derek D; Zamoryakhin, Dmitry; Fox, Keith A A; White, Harvey D; Armstrong, Paul W; Ohman, E Magnus; Prabhakaran, Dorairaj

2015-02-01

To study the impact of national economic and human development status on patient profiles and outcomes in the setting of acute coronary syndrome (ACS). We conducted a retrospective analysis of the Targeted Platelet Inhibition to Clarify the Optimal Strategy to Medically Manage Acute Coronary Syndromes trial (TRILOGY ACS) population (51 countries; 9301 patients). Outcome measures compared baseline characteristics and clinical outcomes through 30 months by 2010 country-level United Nations Human Development Indices (HDIs) and per-capita gross national income. TRILOGY ACS enrolled 3659 patients from 27 very-high HDI countries, 3744 from 18 high-HDI countries and 1898 from 6 medium-HDI countries. Baseline characteristics of groups varied significantly, with the medium-HDI group having a lower mean age (63.0 years, vs 65.0 and 68.0 years for high-HDI and very-high HDI, respectively; p<0.001), lower baseline Global Registry of Acute Coronary Events risk score and lower rate of non-ST-segment elevation myocardial infarction (58.0%, vs 62.2% and 83.9% among high-HDI and very-high HDI, respectively). Medium-HDI and high-HDI patients had lower unadjusted 30-month rates for the composite of cardiovascular death/myocardial infarction/stroke (17.6%, 16.9% and 23.1% for medium-HDI, high-HDI and very-high HDI, respectively); this difference disappeared after adjusting for baseline characteristics. Adjusted HRs for the composite endpoint were lower in lower-income/middle-income countries vs upper-income/middle-income (0.791(95% CI 0.632 to 0.990)) and high-income countries (0.756 (95% CI 0.616 to 0.928)), with differences largely attributable to myocardial infarction rates. Clinical patient profiles differed substantially by country HDI groupings. Lower unadjusted event rates in medium-HDI countries may be explained by younger age and lower comorbidity burden among these countries' patients. This heterogeneity in patient recruitment across country HDI groupings may have important implications for future global ACS trial design. NCT00699998. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Values Reflected in the Human Development Index

ERIC Educational Resources Information Center

Lind, Niels

2004-01-01

The Human Development Index (HDI) implicitly defines "human development" and ranks countries accordingly. To elucidate the HDI's meaning of "human development," the paper examines the sensitivity of the HDI to changes in its components, namely social indicators of education, longevity and standard of living. The HDI is next compared with two…

Enhancement of antibacterial properties of polyurethanes by chitosan and heparin immobilization

NASA Astrophysics Data System (ADS)

Kara, Filiz; Aksoy, E. Ayse; Yuksekdag, Zehranur; Aksoy, Serpil; Hasirci, Nesrin

2015-12-01

Being antibacterial is a required property for the materials used in medical devices and instruments. Polyurethanes (PUs) are one class of polymers widely used in the production of devices that especially come in contact with blood (e.g. heart valves, blood vessels, vascular grafts and catheters). In this study, hexamethylene diisocyanate based polyurethanes (PUh) were synthesized and antibacterial and anti-adhesive properties were added by immobilizing chitosan (CH) and heparin (Hep) on the samples of PUh via a stepwise process. Chemistry and topography of the modified film samples (PUh-CH and PUh-CH-Hep) were examined by Fourier Transform Infrared Spectrophotometry-Attenuated Total Reflectance (FTIR-ATR), Electron Spectroscopy for Chemical Analysis (ESCA) and Atomic Force Microscopy (AFM), and surface free energy (SFE) values after each step were determined by goniometer. PUh-CH and PUh-CH-Hep samples were found to be antibacterial against Staphylococcus aureus (S. aureus) and Staphylococcus epidermidis (S. epidermidis) (both Gram positive) and Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) (both Gram negative) bacteria, and bacterial adhesion results showed a significant decrease in the number of viable bacteria on both modified samples where PUh-CH-Hep was the most effective. The findings of this study show that polymeric surfaces can be effectively modified and converted to be antibacterial by chitosan and heparin immobilization, and presence of both chemicals enhance efficacy against bacteria.

Patch-test reactions to plastic and glue allergens.

PubMed

Kanerva, L; Jolanki, R; Alanko, K; Estlander, T

1999-07-01

Plastics and glues are common causes of occupational dermatoses, but only few reports have dealt with patch-test reactions caused by plastic and glue allergens. Patients exposed to plastics and remitted to an occupational dermatology clinic, were patch-tested with 50-53 plastic and glue allergens during a 6-year period. Conventional patch-test techniques were used. The most common causes of allergic patch-test reactions in 360 patients were novolac epoxy resin (5.1%), phenol formaldehyde resin (3.1%), 4-tert-butylcatechol (2.6%), phenyl glycidyl ether (2.6%), diaminodiphenyl methane (2.2%), benzoyl peroxide (2.2%), hexamethylene tetramine (2.0%) and o-cresyl glycidyl ether (1.6%). The allergens that most often elicited irritant patch-test reactions were: benzoyl peroxide (9.5%), abitol alcohol (3.6%), hydroquinone (3.1%), acid-catalyzed phenol formaldehyde resin (2.5%) and toluene diisocyanate (1.9%). Twenty-six out of 53 chemicals caused no allergic reaction during the 6-year period. Plastic allergens in the standard series provoked allergic reactions with formaldehyde (5.8%), diglycidyl ether of bisphenol A (3.2%), 4-tert-butylphenol-formaldehyde-resin (1.1%), toluene sulphonamide formaldehyde-resin (1.1%) and triethylenglycol diacrylate (0.4%). Although half of the plastic chemicals gave no allergic patch-test reactions during a 6-year period, with unusual allergens this low yield needs to be accepted, because otherwise rare allergies will not be detected. Also a negative reaction has diagnostic value.

Castor Oil Based Polyurethanes: Synthesis and Characterization

NASA Astrophysics Data System (ADS)

Macalino, AD; Salen, VA; Reyes, LQ

2017-09-01

In this study, polyurethanes based on castor oil and 1,6-hexamethylene diisocyanate (HMDI) were synthesized with varying weight ratio of the castor oil and HMDI. The formation of urethane linkages was verified through the use of a fourier transform infrared spectroscopy (FTIR). The hydrophilicity of the films was evaluated through the use of a contact angle meter and it was found that the contact angle of all the films were below 90 degrees which confirms their hydrophilicity. The thermal stability of the PU films were studies through the use of a thermal gravimetric analyzer and found that all of the polyurethane films exhibited two weight loss events at elevated temperatures wherein the first weight loss event was observed to occur at 285°C to 384°C while the second weight loss event was observed at around 521°C to 551°C. The hardness, elastic modulus, and tensile elongation of the PU films were determined by using a universal testing machine (UTM) where it was found out that the hardness and the elastic modulus of the film is directly proportional with HMDI loading while the tensile elongation is inversely proportional to it. Lastly, it was known through the swelling studies of the PU films that it does not swell, this is due to the presence of unreacted triglycerides in the material, which prevents water from permeating to the films.

Biocompatible, Biodegradable, and Electroactive Polyurethane-Urea Elastomers with Tunable Hydrophilicity for Skeletal Muscle Tissue Engineering.

PubMed

Chen, Jing; Dong, Ruonan; Ge, Juan; Guo, Baolin; Ma, Peter X

2015-12-30

It remains a challenge to develop electroactive and elastic biomaterials to mimic the elasticity of soft tissue and to regulate the cell behavior during tissue regeneration. We designed and synthesized a series of novel electroactive and biodegradable polyurethane-urea (PUU) copolymers with elastomeric property by combining the properties of polyurethanes and conducting polymers. The electroactive PUU copolymers were synthesized from amine capped aniline trimer (ACAT), dimethylol propionic acid (DMPA), polylactide, and hexamethylene diisocyanate. The electroactivity of the PUU copolymers were studied by UV-vis spectroscopy and cyclic voltammetry. Elasticity and Young's modulus were tailored by the polylactide segment length and ACAT content. Hydrophilicity of the copolymer films was tuned by changing DMPA content and doping of the copolymer. Cytotoxicity of the PUU copolymers was evaluated by mouse C2C12 myoblast cells. The myogenic differentiation of C2C12 myoblasts on copolymer films was also studied by analyzing the morphology of myotubes and relative gene expression during myogenic differentiation. The chemical structure, thermal properties, surface morphology, and processability of the PUU copolymers were characterized by NMR, FT-IR, gel permeation chromatography (GPC), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and solubility testing, respectively. Those biodegradable electroactive elastic PUU copolymers are promising materials for repair of soft tissues such as skeletal muscle, cardiac muscle, and nerve.

Smart hydrogel-functionalized textile system with moisture management property for skin application

NASA Astrophysics Data System (ADS)

Wang, Xiaowen; Hu, Huawen; Yang, Zongyue; He, Liang; Kong, Yeeyee; Fei, Bin; Xin, John H.

2014-12-01

In this study, a functional textile-based material for topical skin application was fabricated by coating a thermoresponsive hydrogel onto one side of absorbent nonwoven fabric. The thermoresponsive hydrogel was synthesized easily through coupling of poly (ethylene glycol) (PEG) and poly (ɛ-caprolactone) (PCL) with hexamethylene diisocyanate (HMDI) as a chemical linker. The chemical structure of the as-prepared triblock copolymer hydrogel was unraveled by FTIR and 1H NMR analysis. The hydrogel showed a temperature-triggered sol-gel transition behavior and high potential for use as drug controlled release. When the surrounding temperature was close to the skin temperature of around 34 °C, it became a moisture management system where the liquids including sweat, blood, and other body fluids can be transported unidirectionally from one fabric side with the hydrophobic hydrogel coating to the untreated opposite side. This thereby showed that the thermoresponsive hydrogel-coated textile materials had a function to keep topical skin area clean, breathable, and comfortable, thus suggesting a great potential and significance for long-term skin treatment application. The structure and surface morphology of the thermoresponsive hydrogel, in vitro drug release behavior, and the mechanism of unidirectional water transport were investigated in detail. Our success in preparation of the functional textile composites will pave the way for development of various polymer- or textile-based functional materials that are applicable in the real world.

40 CFR 721.10610 - Toluene diisocyanate, polymers with polyalkylene glycol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Toluene diisocyanate, polymers with... New Uses for Specific Chemical Substances § 721.10610 Toluene diisocyanate, polymers with polyalkylene... substances identified generically as toluene diisocyanate, polymers with polyalkylene glycol (PMNs P-11-635...

40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with alkanediol...

40 CFR 721.10610 - Toluene diisocyanate, polymers with polyalkylene glycol (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Toluene diisocyanate, polymers with... New Uses for Specific Chemical Substances § 721.10610 Toluene diisocyanate, polymers with polyalkylene... substances identified generically as toluene diisocyanate, polymers with polyalkylene glycol (PMNs P-11-635...

40 CFR 721.10608 - Aliphatic diisocyanate polymer with alkanediol and alkylglycol (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Aliphatic diisocyanate polymer with... Significant New Uses for Specific Chemical Substances § 721.10608 Aliphatic diisocyanate polymer with.... (1) The chemical substance identified generically as aliphatic diisocyanate polymer with alkanediol...

The impact of the HDI on the association of psychosocial work demands with sickness absence and presenteeism.

PubMed

Muckenhuber, Johanna; Burkert, Nathalie; Dorner, Thomas E; Großschädl, Franziska; Freidl, Wolfgang

2014-10-01

The purpose of this study was to determine whether psychosocial work demands have a different impact on sickness absence and presenteeism in countries with a high vs. countries with a low Human Development Index (HDI). This article is based on an analysis of the fifth European Working Conditions Survey. We investigated single items as well as complex constructs and indices. Sickness absence and presenteeism were measured as outcome variables. Following the model of Karasek and Theorell, we measured the HDI at the macro level and psychosocial job demands at the micro level as independent variables. The multivariate multilevel analysis reveals a significant association between the HDI and the number of days recorded for sickness absence. In countries with a higher HDI, people report a lower number of days with sickness absence. Higher psychosocial job demands are associated with poorer health. There are significant cross-level interaction effects between psychosocial job demands and the HDI for these associations. Psychosocial job demands are stronger associated with sickness absence and presenteeism in high-HDI than in low-HDI countries. We argue that Public Health Actions that are connected to work characteristics need to take into consideration the level of HDI of the countries. In low- and high-HDI countries, different actions could be necessary to reach the needs of the working population. © The Author 2013. Published by Oxford University Press on behalf of the European Public Health Association. All rights reserved.

MANAGEMENT AND OUTCOMES FROM APPENDECTOMY: AN INTERNATIONAL, PROSPECTIVE, MULTICENTRE STUDY.

PubMed

Camilleri-Brennan, J; Drake, T; Spence, R; Bhangu, A; Harrison, E

2017-09-01

To identify variation in surgical management and outcomes of appendicitis across low, middle and high Human Development Index (HDI) country groups. Multi-centre, international prospective cohort study of consecutive patients undergoing emergency appendectomy over a 6-month period. Follow-up lasted 30 days. Primary outcome measure was overall complication rate. 4546 patients from 52 countries underwent appendectomy (2499 high, 1540 middle and 507 low HDI groups). Complications were more frequent in low-HDI (OR 3.81, 95% CI 2.78 to 5.19, p < 0.001) and middle-HDI countries (OR 2.99, 95% CI 2.34-3.84, p < 0.001) compared with high- HDI countries, but differences were adjusted out by case-mix and hospital structural factors. Surgical site infection (SSI) rates were higher in low-HDI (OR 2.57, 95% CI 1.33 to 4.99, p=0.005) but not middle-HDI (OR 1.38, 95% CI 0.76 to 2.52, p=0.291) compared with high-HDI countries after adjustment. A laparoscopic approach was common in high-HDI countries (1693/2499, 67.7%), but infrequent in low- (41/507, 8.1%) and middle-HDI (132/1540, 8.6%) groups. After accounting for case-mix, laparoscopy was still associated with fewer complications (OR 0.55, 95% CI 0.42 to 0.71, p< 0.001) and SSIs (OR 0.22, 95% CI 0.14 to 0.33, p<0.001). The number needed-to-treat with laparoscopic surgery to save an SSI was lower in low-HDI countries (NNT=6, 95% CI 4 to 9) than in high-HDI countries (NNT=9, 95% CI 6 to 16). In propensity-score matched groups within low- and middle- HDI countries, laparoscopy was still associated with fewer overall complications (OR 0.23 95% CI 0.11 to 0.44) and SSI (OR 0.21 95% CI 0.09 to 0.45). Outcomes from appendectomy vary worldwide. A laparoscopic approach is associated with better outcomes and availability appears to differ by country HDI. There are profound clinical, operational and financial barriers to the introduction of laparoscopy that if overcome, could result in significantly improved outcomes for patients in low-resource environments, with potential for wider health-system benefits.

Determinants of morbidity and mortality following emergency abdominal surgery in children in low-income and middle-income countries.

PubMed

2016-01-01

Child health is a key priority on the global health agenda, yet the provision of essential and emergency surgery in children is patchy in resource-poor regions. This study was aimed to determine the mortality risk for emergency abdominal paediatric surgery in low-income countries globally. Multicentre, international, prospective, cohort study. Self-selected surgical units performing emergency abdominal surgery submitted prespecified data for consecutive children aged <16 years during a 2-week period between July and December 2014. The United Nation's Human Development Index (HDI) was used to stratify countries. The main outcome measure was 30-day postoperative mortality, analysed by multilevel logistic regression. This study included 1409 patients from 253 centres in 43 countries; 282 children were under 2 years of age. Among them, 265 (18.8%) were from low-HDI, 450 (31.9%) from middle-HDI and 694 (49.3%) from high-HDI countries. The most common operations performed were appendectomy, small bowel resection, pyloromyotomy and correction of intussusception. After adjustment for patient and hospital risk factors, child mortality at 30 days was significantly higher in low-HDI (adjusted OR 7.14 (95% CI 2.52 to 20.23), p<0.001) and middle-HDI (4.42 (1.44 to 13.56), p=0.009) countries compared with high-HDI countries, translating to 40 excess deaths per 1000 procedures performed. Adjusted mortality in children following emergency abdominal surgery may be as high as 7 times greater in low-HDI and middle-HDI countries compared with high-HDI countries. Effective provision of emergency essential surgery should be a key priority for global child health agendas. NCT02179112; Pre-results.

Determinants of morbidity and mortality following emergency abdominal surgery in children in low-income and middle-income countries

PubMed Central

Ademuyiwa, Adesoji O

2016-01-01

Background Child health is a key priority on the global health agenda, yet the provision of essential and emergency surgery in children is patchy in resource-poor regions. This study was aimed to determine the mortality risk for emergency abdominal paediatric surgery in low-income countries globally. Methods Multicentre, international, prospective, cohort study. Self-selected surgical units performing emergency abdominal surgery submitted prespecified data for consecutive children aged <16 years during a 2-week period between July and December 2014. The United Nation's Human Development Index (HDI) was used to stratify countries. The main outcome measure was 30-day postoperative mortality, analysed by multilevel logistic regression. Results This study included 1409 patients from 253 centres in 43 countries; 282 children were under 2 years of age. Among them, 265 (18.8%) were from low-HDI, 450 (31.9%) from middle-HDI and 694 (49.3%) from high-HDI countries. The most common operations performed were appendectomy, small bowel resection, pyloromyotomy and correction of intussusception. After adjustment for patient and hospital risk factors, child mortality at 30 days was significantly higher in low-HDI (adjusted OR 7.14 (95% CI 2.52 to 20.23), p<0.001) and middle-HDI (4.42 (1.44 to 13.56), p=0.009) countries compared with high-HDI countries, translating to 40 excess deaths per 1000 procedures performed. Conclusions Adjusted mortality in children following emergency abdominal surgery may be as high as 7 times greater in low-HDI and middle-HDI countries compared with high-HDI countries. Effective provision of emergency essential surgery should be a key priority for global child health agendas. Trial registration number NCT02179112; Pre-results. PMID:28588977

Effects of Human Development Index and Its Components on Colorectal Cancer Incidence and Mortality: a Global Ecological Study.

PubMed

Khazaei, Salman; Rezaeian, Shahab; Khazaei, Somayeh; Mansori, Kamyar; Sanjari Moghaddam, Ali; Ayubi, Erfan

2016-01-01

Geographic disparity for colorectal cancer (CRC) incidence and mortality according to the human development index (HDI) might be expected. This study aimed at quantifying the effect measure of association HDI and its components on the CRC incidence and mortality. In this ecological study, CRC incidence and mortality was obtained from GLOBOCAN, the global cancer project for 172 countries. Data were extracted about HDI 2013 for 169 countries from the World Bank report. Linear regression was constructed to measure effects of HDI and its components on CRC incidence and mortality. A positive trend between increasing HDI of countries and age-standardized rates per 100,000 of CRC incidence and mortality was observed. Among HDI components education was the strongest effect measure of association on CRC incidence and mortality, regression coefficients (95% confidence intervals) being 2.8 (2.4, 3.2) and 0.9 (0.8, 1), respectively. HDI and its components were positively related with CRC incidence and mortality and can be considered as targets for prevention and treatment intervention or tracking geographic disparities.

Bioethics and its gatekeepers: does institutional racism exist in leading bioethics journals?

PubMed

Chattopadhyay, Subrata; Myser, Catherine; De Vries, Raymond

2013-03-01

Who are the gatekeepers in bioethics? Does editorial bias or institutional racism exist in leading bioethics journals? We analyzed the composition of the editorial boards of 14 leading bioethics journals by country. Categorizing these countries according to their Human Development Index (HDI), we discovered that approximately 95 percent of editorial board members are based in (very) high-HDI countries, less than 4 percent are from medium-HDI countries, and fewer than 1.5 percent are from low-HDI countries. Eight out of 14 leading bioethics journals have no editorial board members from a medium- or low-HDI country. Eleven bioethics journals have no board members from low-HDI countries. This severe underrepresentation of bioethics scholars from developing countries on editorial boards suggests that bioethics may be affected by institutional racism, raising significant questions about the ethics of bioethics in a global context.

Can education change the world? Education amplifies differences in liberalization values and innovation between developed and developing countries.

PubMed

Van Hiel, Alain; Van Assche, Jasper; De Cremer, David; Onraet, Emma; Bostyn, Dries; Haesevoets, Tessa; Roets, Arne

2018-01-01

The present study investigated the relationship between level of education and liberalization values in large, representative samples administered in 96 countries around the world (total N = 139,991). These countries show meaningful variation in terms of the Human Development Index (HDI), ranging from very poor, developing countries to prosperous, developed countries. We found evidence of cross-level interactions, consistently showing that individuals' level of education was associated with an increase in their liberalization values in higher HDI societies, whereas this relationship was curbed in lower HDI countries. This enhanced liberalization mindset of individuals in high HDI countries, in turn, was related to better scores on national indices of innovation. We conclude that this 'education amplification effect' widens the gap between lower and higher HDI countries in terms of liberalized mentality and economic growth potential. Policy implications for how low HDI countries can counter this gap are discussed.

Human Development Index (HDI) of the maternal country of origin as a predictor of perinatal outcomes - a longitudinal study conducted in Spain.

PubMed

Garcia-Tizon Larroca, S; Arevalo-Serrano, J; Duran Vila, A; Pintado Recarte, M P; Cueto Hernandez, I; Solis Pierna, A; Lizarraga Bonelli, S; De Leon-Luis, J

2017-09-21

In an era of worldwide population displacement, recent studies have identified strong associations between social situations and perinatal outcomes among immigrants. Little is known about the effect of maternal social background on pregnancy outcomes. The Human Development Index (HDI) assesses the following dimensions of human development: life expectancy, education level and income. The objective of our study was to determine if maternal HDI may be used to identify women at increased odds of poor pregnancy outcomes. We conducted a longitudinal population-based study in a tertiary centre in Madrid, Spain. The outcome variables were maternal and perinatal/antenatal mortality, preeclampsia (PE), low birth weight (LBW), gestational diabetes mellitus (GDM), preterm delivery (PTD) before 37 and 34 gestational weeks, abnormal cardiotocography (CTG) during delivery, C-section (CS) due to abnormal CTG, pH < 7.10 at birth, Apgar at 5 min ≤ 7, and resuscitation type ≥3. We performed multivariate logistic regression analyses adjusted for potential confounding variables to evaluate the associations between maternal HDI and perinatal outcomes. In total, 38,719 singleton infants who were born in our maternity ward between 2010 and 2016 and had perinatal outcome data available were included in this study. The neonates of women from medium/low HDI countries had significantly lower odds of low birth weight (LBW) than their very high HDI country counterparts (OR 0.63, 95% CI 0.55-0.72). However, the odds of PTD before 37 gestational weeks and PE were higher in the medium/low HDI group than the very high HDI group (OR 1.26, 95% CI 1.04-1.53; OR 1.35, 95% CI 1.02-1.79, respectively). Poorer neonatal outcomes were identified in the medium/low HDI group than the very high HDI group, including greater odds of abnormal CTG, CS due to abnormal CTG and Apgar 2 ≤ 7 (p < 0.05). Our findings suggest that the infants of mothers from medium/low HDI had lower odds of LBW but higher odds of PTD, PE and poor neonatal outcomes. These results support the hypothesis that maternal HDI can be used to understand the impact of maternal origin on pregnancy outcomes. Further studies are needed to confirm its validity.

Conjugation of diisocyanate side chains to dimethacrylate reduces polymerization shrinkage and increases the hardness of composite resins.

PubMed

Jan, Yih-Dean; Lee, Bor-Shiunn; Lin, Chun-Pin; Tseng, Wan-Yu

2014-04-01

Polymerization shrinkage is one of the main causes of dental restoration failure. This study tried to conjugate two diisocyanate side chains to dimethacrylate resins in order to reduce polymerization shrinkage and increase the hardness of composite resins. Diisocyanate, 2-hydroxyethyl methacrylate, and bisphenol A dimethacrylate were reacted in different ratios to form urethane-modified new resin matrices, and then mixed with 50 wt.% silica fillers. The viscosities of matrices, polymerization shrinkage, surface hardness, and degrees of conversion of experimental composite resins were then evaluated and compared with a non-modified control group. The viscosities of resin matrices increased with increasing diisocyanate side chain density. Polymerization shrinkage and degree of conversion, however, decreased with increasing diisocyanate side chain density. The surface hardness of all diisocyanate-modified groups was equal to or significantly higher than that of the control group. Conjugation of diisocyanate side chains to dimethacrylate represents an effective means of reducing polymerization shrinkage and increasing the surface hardness of dental composite resins. Copyright © 2012. Published by Elsevier B.V.

Laparoscopy in management of appendicitis in high-, middle-, and low-income countries: a multicenter, prospective, cohort study.

PubMed

2018-04-05

Appendicitis is the most common abdominal surgical emergency worldwide. Differences between high- and low-income settings in the availability of laparoscopic appendectomy, alternative management choices, and outcomes are poorly described. The aim was to identify variation in surgical management and outcomes of appendicitis within low-, middle-, and high-Human Development Index (HDI) countries worldwide. This is a multicenter, international prospective cohort study. Consecutive sampling of patients undergoing emergency appendectomy over 6 months was conducted. Follow-up lasted 30 days. 4546 patients from 52 countries underwent appendectomy (2499 high-, 1540 middle-, and 507 low-HDI groups). Surgical site infection (SSI) rates were higher in low-HDI (OR 2.57, 95% CI 1.33-4.99, p = 0.005) but not middle-HDI countries (OR 1.38, 95% CI 0.76-2.52, p = 0.291), compared with high-HDI countries after adjustment. A laparoscopic approach was common in high-HDI countries (1693/2499, 67.7%), but infrequent in low-HDI (41/507, 8.1%) and middle-HDI (132/1540, 8.6%) groups. After accounting for case-mix, laparoscopy was still associated with fewer overall complications (OR 0.55, 95% CI 0.42-0.71, p < 0.001) and SSIs (OR 0.22, 95% CI 0.14-0.33, p < 0.001). In propensity-score matched groups within low-/middle-HDI countries, laparoscopy was still associated with fewer overall complications (OR 0.23 95% CI 0.11-0.44) and SSI (OR 0.21 95% CI 0.09-0.45). A laparoscopic approach is associated with better outcomes and availability appears to differ by country HDI. Despite the profound clinical, operational, and financial barriers to its widespread introduction, laparoscopy could significantly improve outcomes for patients in low-resource environments. NCT02179112.

Functional Inactivation of Putative Photosynthetic Electron Acceptor Ferredoxin C2 (FdC2) Induces Delayed Heading Date and Decreased Photosynthetic Rate in Rice

PubMed Central

Ruan, Banpu; Kang, Shujing; He, Lei; Zhang, Sen; Dong, Guojun; Hu, Jiang; Zeng, Dali; Zhang, Guangheng; Gao, Zhenyu; Ren, Deyong; Hu, Xingming; Chen, Guang; Guo, Longbiao; Qian, Qian; Zhu, Li

2015-01-01

Ferredoxin (Fd) protein as unique electron acceptor, involved in a variety of fundamental metabolic and signaling processes, which is indispensable for plant growth. The molecular mechanisms of Fd such as regulation of electron partitioning, impact of photosynthetic rate and involvement in the carbon fixing remain elusive in rice. Here we reported a heading date delay and yellowish leaf 1 (hdy1) mutant derived from Japonica rice cultivar “Nipponbare” subjected to EMS treatment. In the paddy field, the hdy1 mutant appeared at a significantly late heading date and had yellow-green leaves during the whole growth stage. Further investigation indicated that the abnormal phenotype of hdy1 was connected with depressed pigment content and photosynthetic rate. Genetic analysis results showed that the hdy1 mutant phenotype was caused by a single recessive nuclear gene mutation. Map-based cloning revealed that OsHDY1 is located on chromosome 3 and encodes an ortholog of the AtFdC2 gene. Complementation and overexpression, transgenic plants exhibited the mutant phenotype including head date, leaf color and the transcription levels of the FdC2 were completely rescued by transformation with OsHDY1. Real-time PCR revealed that the expression product of OsHDY1 was detected in almost all of the organs except root, whereas highest expression levels were observed in seeding new leaves. The lower expression levels of HDY1 and content of iron were detected in hdy1 than WT’s. The FdC2::GFP was detected in the chloroplasts of rice. Real-time PCR results showed that the expression of many photosynthetic electron transfer related genes in hdy1 were higher than WT. Our results suggest that OsFdC2 plays an important role in photosynthetic rate and development of heading date by regulating electron transfer and chlorophyll content in rice. PMID:26598971

The effects of crosslinkers on physical, mechanical, and cytotoxic properties of gelatin sponge prepared via in-situ gas foaming method as a tissue engineering scaffold.

PubMed

Poursamar, S Ali; Lehner, Alexander N; Azami, Mahmoud; Ebrahimi-Barough, Somayeh; Samadikuchaksaraei, Ali; Antunes, A P M

2016-06-01

In this study porous gelatin scaffolds were prepared using in-situ gas foaming, and four crosslinking agents were used to determine a biocompatible and effective crosslinker that is suitable for such a method. Crosslinkers used in this study included: hexamethylene diisocyanate (HMDI), poly(ethylene glycol) diglycidyl ether (epoxy), glutaraldehyde (GTA), and genipin. The prepared porous structures were analyzed using Fourier Transform Infrared Spectroscopy (FT-IR), thermal and mechanical analysis as well as water absorption analysis. The microstructures of the prepared samples were analyzed using Scanning Electron Microscopy (SEM). The effects of the crosslinking agents were studied on the cytotoxicity of the porous structure indirectly using MTT analysis. The affinity of L929 mouse fibroblast cells for attachment on the scaffold surfaces was investigated by direct cell seeding and DAPI-staining technique. It was shown that while all of the studied crosslinking agents were capable of stabilizing prepared gelatin scaffolds, there are noticeable differences among physical and mechanical properties of samples based on the crosslinker type. Epoxy-crosslinked scaffolds showed a higher capacity for water absorption and more uniform microstructures than the rest of crosslinked samples, whereas genipin and GTA-crosslinked scaffolds demonstrated higher mechanical strength. Cytotoxicity analysis showed the superior biocompatibility of the naturally occurring genipin in comparison with other synthetic crosslinking agents, in particular relative to GTA-crosslinked samples. Copyright © 2016 Elsevier B.V. All rights reserved.

Compatibility study of trans-1,4,5,8-tetranitro-1,4,5,8-tetraazadecalin (TNAD) with some energetic components and inert materials.

PubMed

Yan, Qi-Long; Xiao-Jiang, Li; La-Ying, Zhang; Ji-Zhen, Li; Hong-Li, Li; Zi-Ru, Liu

2008-12-30

The compatibility of trans-1,4,5,8-tetranitro-1,4,5,8-tetraazadecalin (TNAD) with some energetic components and inert materials of solid propellants was studied by using the pressure DSC method where, cyclotetramethylenetetranitroamine (HMX), cyclotrimethylenetrinitramine (RDX), 1,4-dinitropiperazine (DNP), 1.25/1-NC/NG mixture, lead 3-nitro-1,2,4-triazol-5-onate (NTO-Pb), aluminum powder (Al, particle size=13.6microm) and N-nitrodihydroxyethylaminedinitrate (DINA) were used as energetic components and polyethylene glycol (PEG), polyoxytetramethylene-co-oxyethylene (PET), addition product of hexamethylene diisocyanate and water (N-100), 2-nitrodianiline (2-NDPA), 1,3-dimethyl-1,3-diphenyl urea (C2), carbon black (C.B.), aluminum oxide (Al2O3), cupric 2,4-dihydroxy-benzoate (beta-Cu), cupric adipate (AD-Cu) and lead phthalate (phi-Pb) were used as inert materials. It was concluded that the binary systems of TNAD with NTO-Pb, RDX, PET and Al powder are compatible, and systems of TNAD with DINA and HMX are slightly sensitive, and with 2-NDPA, phi-Pb, beta-Cu, AD-Cu and Al2O3 are sensitive, and with PEG, N-100, C2 and C.B. are incompatible. The impact and friction sensitivity data of the TNAD and TNAD in combination with the other energetic materials under present study was also obtained, and there was no consequential affiliation between sensitivity and compatibility.

Synthesis and Characterization of Elastin-Mimetic Hybrid Polymers with Multiblock, Alternating Molecular Architecture and Elastomeric Properties

PubMed Central

Grieshaber, Sarah E.; Farran, Alexandra J. E.; Lin-Gibson, Sheng; Kiick, Kristi L.; Jia, Xinqiao

2009-01-01

We are interested in developing elastin–mimetic hybrid polymers (EMHPs) that capture the multiblock molecular architecture of tropoelastin as well as the remarkable elasticity of mature elastin. In this study, multiblock EMHPs containing flexible synthetic segments based on poly(ethylene glycol) (PEG) alternating with alanine-rich, lysine-containing peptides were synthesized by step-growth polymerization using α,ω-azido-PEG and alkyne-terminated AKA3KA (K = lysine, A = alanine) peptide, employing orthogonal click chemistry. The resulting EMHPs contain an estimated three to five repeats of PEG and AKA3KA and have an average molecular weight of 34 kDa. While the peptide alone exhibited α-helical structures at high pH, the fractional helicity for EMHPs was reduced. Covalent cross-linking of EMHPs with hexamethylene diisocyanate (HMDI) through the lysine residue in the peptide domain afforded an elastomeric hydrogel (xEMHP) with a compressive modulus of 0.12 MPa when hydrated. The mechanical properties of xEMHP are comparable to a commercial polyurethane elastomer (Tecoflex SG80A) under the same conditions. In vitro toxicity studies showed that while the soluble EMHPs inhibited the growth of primary porcine vocal fold fibroblasts (PVFFs) at concentrations ≥0.2 mg/mL, the cross-linked hybrid elastomers did not leach out any toxic reagents and allowed PVFFs to grow and proliferate normally. The hybrid and modular approach provides a new strategy for developing elastomeric scaffolds for tissue engineering. PMID:19763157

HPAM: Hirshfeld Partitioned Atomic Multipoles

PubMed Central

Elking, Dennis M.; Perera, Lalith; Pedersen, Lee G.

2011-01-01

An implementation of the Hirshfeld (HD) and Hirshfeld-Iterated (HD-I) atomic charge density partitioning schemes is described. Atomic charges and atomic multipoles are calculated from the HD and HD-I atomic charge densities for arbitrary atomic multipole rank lmax on molecules of arbitrary shape and size. The HD and HD-I atomic charges/multipoles are tested by comparing molecular multipole moments and the electrostatic potential (ESP) surrounding a molecule with their reference ab initio values. In general, the HD-I atomic charges/multipoles are found to better reproduce ab initio electrostatic properties over HD atomic charges/multipoles. A systematic increase in precision for reproducing ab initio electrostatic properties is demonstrated by increasing the atomic multipole rank from lmax = 0 (atomic charges) to lmax = 4 (atomic hexadecapoles). Both HD and HD-I atomic multipoles up to rank lmax are shown to exactly reproduce ab initio molecular multipole moments of rank L for L ≤ lmax. In addition, molecular dipole moments calculated by HD, HD-I, and ChelpG atomic charges only (lmax = 0) are compared with reference ab initio values. Significant errors in reproducing ab initio molecular dipole moments are found if only HD or HD-I atomic charges used. PMID:22140274

An Overview of the Evidence and Mechanisms of Herb–Drug Interactions

PubMed Central

Fasinu, Pius S.; Bouic, Patrick J.; Rosenkranz, Bernd

2012-01-01

Despite the lack of sufficient information on the safety of herbal products, their use as alternative and/or complementary medicine is globally popular. There is also an increasing interest in medicinal herbs as precursor for pharmacological actives. Of serious concern is the concurrent consumption of herbal products and conventional drugs. Herb–drug interaction (HDI) is the single most important clinical consequence of this practice. Using a structured assessment procedure, the evidence of HDI presents with varying degree of clinical significance. While the potential for HDI for a number of herbal products is inferred from non-human studies, certain HDIs are well established through human studies and documented case reports. Various mechanisms of pharmacokinetic HDI have been identified and include the alteration in the gastrointestinal functions with consequent effects on drug absorption; induction and inhibition of metabolic enzymes and transport proteins; and alteration of renal excretion of drugs and their metabolites. Due to the intrinsic pharmacologic properties of phytochemicals, pharmacodynamic HDIs are also known to occur. The effects could be synergistic, additive, and/or antagonistic. Poor reporting on the part of patients and the inability to promptly identify HDI by health providers are identified as major factors limiting the extensive compilation of clinically relevant HDIs. A general overview and the significance of pharmacokinetic and pharmacodynamic HDI are provided, detailing basic mechanism, and nature of evidence available. An increased level of awareness of HDI is necessary among health professionals and drug discovery scientists. With the increasing number of plant-sourced pharmacological actives, the potential for HDI should always be assessed in the non-clinical safety assessment phase of drug development process. More clinically relevant research is also required in this area as current information on HDI is insufficient for clinical applications. PMID:22557968

Prevalence of metastasis at diagnosis of osteosarcoma: an international comparison

PubMed Central

Marko, Tracy A.; Diessner, Brandon J.; Spector, Logan G.

2016-01-01

Background Osteosarcoma is the most common primary malignant bone tumor in many countries, with metastatic disease responsible for most patient deaths. This study compares the prevalence of metastatic osteosarcoma at diagnosis across countries to inform the critical question of whether diagnostic delay or tumor biology drives metastases development prior to diagnosis. Procedure A literature search of the PubMed database was conducted to compare the prevalence of metastatic disease at the time of OS diagnosis between countries. A pooled prevalence with 95% confidence intervals was calculated for each study meeting inclusion criteria. Studies were grouped for analysis based on human development index (HDI) scores. Results Our analysis found an 18% (95% CI: 15%, 20%) average global pooled proportion of metastasis at osteosarcoma diagnosis. The average prevalence of metastasis at diagnosis increased as HDI groupings decreased, with very high HDI, high HDI, and medium/ low HDI groups found to be 15% (95% CI: 13%, 17%), 20% (95% CI: 14%, 28%), and 31% (95% CI: 15%, 52%), respectively. Conclusions Our evidence suggests there is a biological baseline for metastatic OS at diagnosis, which is observed in countries with very high HDI. In countries with medium/ low HDI, where there are more barriers to accessing healthcare, the higher prevalence of metastasis may result from treatment delay or an artificial prevalence inflation due to patients with less severe symptoms not presenting to clinic. Additional research in countries with medium/ low HDI may reveal that earlier detection and treatment could improve patient outcomes in those countries. PMID:26929018

Surgical site infection after gastrointestinal surgery in high-income, middle-income, and low-income countries: a prospective, international, multicentre cohort study.

PubMed

2018-05-01

Surgical site infection (SSI) is one of the most common infections associated with health care, but its importance as a global health priority is not fully understood. We quantified the burden of SSI after gastrointestinal surgery in countries in all parts of the world. This international, prospective, multicentre cohort study included consecutive patients undergoing elective or emergency gastrointestinal resection within 2-week time periods at any health-care facility in any country. Countries with participating centres were stratified into high-income, middle-income, and low-income groups according to the UN's Human Development Index (HDI). Data variables from the GlobalSurg 1 study and other studies that have been found to affect the likelihood of SSI were entered into risk adjustment models. The primary outcome measure was the 30-day SSI incidence (defined by US Centers for Disease Control and Prevention criteria for superficial and deep incisional SSI). Relationships with explanatory variables were examined using Bayesian multilevel logistic regression models. This trial is registered with ClinicalTrials.gov, number NCT02662231. Between Jan 4, 2016, and July 31, 2016, 13 265 records were submitted for analysis. 12 539 patients from 343 hospitals in 66 countries were included. 7339 (58·5%) patient were from high-HDI countries (193 hospitals in 30 countries), 3918 (31·2%) patients were from middle-HDI countries (82 hospitals in 18 countries), and 1282 (10·2%) patients were from low-HDI countries (68 hospitals in 18 countries). In total, 1538 (12·3%) patients had SSI within 30 days of surgery. The incidence of SSI varied between countries with high (691 [9·4%] of 7339 patients), middle (549 [14·0%] of 3918 patients), and low (298 [23·2%] of 1282) HDI (p<0·001). The highest SSI incidence in each HDI group was after dirty surgery (102 [17·8%] of 574 patients in high-HDI countries; 74 [31·4%] of 236 patients in middle-HDI countries; 72 [39·8%] of 181 patients in low-HDI countries). Following risk factor adjustment, patients in low-HDI countries were at greatest risk of SSI (adjusted odds ratio 1·60, 95% credible interval 1·05-2·37; p=0·030). 132 (21·6%) of 610 patients with an SSI and a microbiology culture result had an infection that was resistant to the prophylactic antibiotic used. Resistant infections were detected in 49 (16·6%) of 295 patients in high-HDI countries, in 37 (19·8%) of 187 patients in middle-HDI countries, and in 46 (35·9%) of 128 patients in low-HDI countries (p<0·001). Countries with a low HDI carry a disproportionately greater burden of SSI than countries with a middle or high HDI and might have higher rates of antibiotic resistance. In view of WHO recommendations on SSI prevention that highlight the absence of high-quality interventional research, urgent, pragmatic, randomised trials based in LMICs are needed to assess measures aiming to reduce this preventable complication. DFID-MRC-Wellcome Trust Joint Global Health Trial Development Grant, National Institute of Health Research Global Health Research Unit Grant. Copyright © 2018 The Author(s). Published by Elsevier Ltd. This is an Open Access article under the CC BY 4.0 license. Published by Elsevier Ltd.. All rights reserved.

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2014 CFR

2014-07-01

... polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Pollutants for Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam production—diisocyanate emissions. Each new and existing slabstock affected source shall comply...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Pollutants for Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam production—diisocyanate emissions. Each new and existing slabstock affected source shall comply...

40 CFR 721.10624 - Dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., polymer with ethoxylated, propoxylated polyethers (generic). 721.10624 Section 721.10624 Protection of...,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic). (a) Chemical substance... dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (PMN P-12-326) is subject to...

40 CFR 721.10624 - Dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

..., polymer with ethoxylated, propoxylated polyethers (generic). 721.10624 Section 721.10624 Protection of...,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (generic). (a) Chemical substance... dicyclohexylmethane-4,4'-diisocyanate, polymer with ethoxylated, propoxylated polyethers (PMN P-12-326) is subject to...

Relations between a novel, reliable, and rapid index of arterial compliance (PP-HDI) and well-established inidices of arterial blood pressure (ABP) in a sample of hypertensive elderly subjects.

PubMed

Bergamini, L; Finelli, M E; Bendini, C; Ferrari, E; Veschi, M; Neviani, F; Manni, B; Pelosi, A; Rioli, G; Neri, M

2009-01-01

Hypertension is a risk factor for a long-lasting arterial wall-remodelling leading to stiffness. The rapid method measuring the pulse pressure (PP) by means of the tool of Hypertension Diagnostic Instruments (HDI) called PP-HDI, overcomes some of the problems arising with more-time consuming methods, like ambulatory blood pressure monitoring (ABPM), and give information about the elasticity of the arterial walls. We studied the relationship between the PP-HDI, the large artery compliance (LA-C) and small artery compliance (SA-C) and few well-established indices of arterial blood pressure (ABP) in a sample of 75 hypertensive subjects, aged 65 years and over. Significant correlations between LA-C and heart rate (HR), PP-ABPM and PP-HDI were found. SA-C relates with HR and systolic blood pressure (SBP) measured in lying and standing positions. Applying a stepwise regression analysis, we found that LA-C variance stems from PP-HDI and HR, while SA-C variance stems from SBP in lying position. Receiver operator characteristic (ROC) curves for thresholds of PP showed that PP-HDI reached levels of sensitivity/specificity similar to PP-ABPM. In conclusion, surveillance of ABP through hemo-dynamic indices, in particular of SBP, is essential, nevertheless the advantage of this control is not known in an elderly population where the organ damage is already evident. PP needs necessarily an instrumental measurement. The PP-HDI result is similar in reliability with respect to PPABPM, but is more rapid and well applicable in an elderly population.

Measurement of Social Development: An International Comparison

ERIC Educational Resources Information Center

Ray, Amal Kanti

2008-01-01

PQLI and HDI are the two most popular measures of development, besides per capita income. Over the years, PQLI appears to be not much in use for regional comparisons, especially after the introduction of HDI. While PQLI considers only the physical variables--adult literacy, life expectancy at birth and infant survival rate, HDI has life expectancy…

Human development and South East Asian countries: Special emphasis on India.

PubMed

Sharma, Kalpa

2013-08-31

'Development' is to improve the quality of people's lives by creating an environment for them to engage in a wide range of activities, to be healthy and well nourished, to be knowledgeable and to be able to participate in the community life. The Human Development Index (HDI) is a multi-dimensional index of development as it is the combination of three development indices- health index, education index and income index. This article attempts to compare the HDI and its components between various South East Asian countries. Secondary data is used. India's position on the HDI scale is equivalent to the South East Asian average and rank 134 out of more than 190 countries. In South East Asia, India stood fifth in HDI, behind Sri Lanka, Thailand, Maldives and Indonesia. Country has launched several schemes and programs to improve the health indicators, to provide elementary education to every child and to alleviate poverty. India's HDI value has improved with time but still country has a long way to go in achieving an acceptable HDI. Need is to strengthen the existing schemes and programs.

Human development and South East Asian countries: Special emphasis on India

PubMed Central

Sharma, Kalpa

2013-01-01

‘Development’ is to improve the quality of people's lives by creating an environment for them to engage in a wide range of activities, to be healthy and well nourished, to be knowledgeable and to be able to participate in the community life. The Human Development Index (HDI) is a multi-dimensional index of development as it is the combination of three development indices- health index, education index and income index. This article attempts to compare the HDI and its components between various South East Asian countries. Secondary data is used. India's position on the HDI scale is equivalent to the South East Asian average and rank 134 out of more than 190 countries. In South East Asia, India stood fifth in HDI, behind Sri Lanka, Thailand, Maldives and Indonesia. Country has launched several schemes and programs to improve the health indicators, to provide elementary education to every child and to alleviate poverty. India's HDI value has improved with time but still country has a long way to go in achieving an acceptable HDI. Need is to strengthen the existing schemes and programs. PMID:24251281

40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject to...

40 CFR 721.10606 - Alkyl substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Alkyl substituted alkanediol polymer... alkanediol polymer with aliphatic and alicyclic diisocyanates (generic). (a) Chemical substance and... substituted alkanediol polymer with aliphatic and alicyclic diisocyanates (PMN P-11-486) is subject to...

40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is subject...

40 CFR 721.10605 - Polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Polyoxyalkylene ether, polymer with..., polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (generic). (a) Chemical substance and... polyoxyalkylene ether, polymer with aliphatic diisocyanate, homopolymer, alkanol-blocked (PMN P-11-485) is subject...

The incidence and mortality of ovarian cancer and their relationship with the Human Development Index in Asia

PubMed Central

Razi, Saeid; Ghoncheh, Mahshid; Mohammadian-Hafshejani, Abdollah; Aziznejhad, Hojjat; Mohammadian, Mahdi; Salehiniya, Hamid

2016-01-01

Background The incidence and mortality estimates of ovarian cancer based on human development are essential for planning by policy makers. This study is aimed at investigating the standardised incidence rates (SIR) and standardised mortality rates (SMR) of ovarian cancer and their relationship with the Human Development Index (HDI) in Asian countries. Methods This study was an ecologic study in Asia for assessment of the correlation between SIR, age standardised rates (ASR), and HDI and their details, including life expectancy at birth, mean years of schooling, and gross national income (GNI) per capita. We used the correlation bivariate method for assessment of the correlation between ASR and HDI, and its details. Statistical significance was assumed if P < 0.05. All reported P-values were two-sided. Statistical analyses were performed using SPSS (Version 15.0, SPSS Inc.). Results The highest SIR of ovarian cancer was observed in Singapore, Kazakhstan, and Brunei respectively. Indonesia, Brunei, and Afghanistan had the highest SMR. There was a positive correlation between the HDI and SIR (r = 0.143, p = 0.006). Correlation between SMR of ovarian cancer and HDI was not significant (r = 0.005, p = 052.0). Conclusion According to the findings of this study, between the HDI and SIR, there was a positive correlation, but there was no correlation between the SMR and HDI. PMID:27110284

The incidence and mortality of ovarian cancer and their relationship with the Human Development Index in Asia.

PubMed

Razi, Saeid; Ghoncheh, Mahshid; Mohammadian-Hafshejani, Abdollah; Aziznejhad, Hojjat; Mohammadian, Mahdi; Salehiniya, Hamid

2016-01-01

The incidence and mortality estimates of ovarian cancer based on human development are essential for planning by policy makers. This study is aimed at investigating the standardised incidence rates (SIR) and standardised mortality rates (SMR) of ovarian cancer and their relationship with the Human Development Index (HDI) in Asian countries. This study was an ecologic study in Asia for assessment of the correlation between SIR, age standardised rates (ASR), and HDI and their details, including life expectancy at birth, mean years of schooling, and gross national income (GNI) per capita. We used the correlation bivariate method for assessment of the correlation between ASR and HDI, and its details. Statistical significance was assumed if P < 0.05. All reported P-values were two-sided. Statistical analyses were performed using SPSS (Version 15.0, SPSS Inc.). The highest SIR of ovarian cancer was observed in Singapore, Kazakhstan, and Brunei respectively. Indonesia, Brunei, and Afghanistan had the highest SMR. There was a positive correlation between the HDI and SIR (r = 0.143, p = 0.006). Correlation between SMR of ovarian cancer and HDI was not significant (r = 0.005, p = 052.0). According to the findings of this study, between the HDI and SIR, there was a positive correlation, but there was no correlation between the SMR and HDI.

Mass spectrometry-based analysis of murine bronchoalveolar lavage fluid following respiratory exposure to 4,4'-methylene diphenyl diisocyanate aerosol.

PubMed

Hettick, Justin M; Law, Brandon F; Lin, Chen-Chung; Wisnewski, Adam V; Siegel, Paul D

2018-06-01

1. Diisocyanates are highly reactive electrophiles utilized in the manufacture of a wide range of polyurethane products and have been identified as causative agents of occupational allergic respiratory disease. However, in spite of the significant occupational health burden associated with diisocyanate-induced asthma, the mechanism of disease pathogenesis remains largely unknown. 2. To better understand the fate of inhaled diisocyanates, a nose-only aerosol exposure system was constructed and utilized to expose a BALB/c mouse model to an aerosol generated from 4,4'-methylene diphenyl diisocyanate (MDI). Tissue and bronchoalveolar lavage samples were evaluated 4 and 24 h post-exposure for evidence of diisocyanate-protein haptenation, and a label-free quantitative proteomics strategy was employed to evaluate relative changes to the protein content of the cellular fraction of the lavage fluid. 3. Following MDI aerosol exposure, expression of the number of proteins with immunological or xenobiotic metabolism relevance is increased, including endoplasmin, cytochrome P450 and argininosuccinate synthase. Western blot analysis indicated MDI-conjugated protein in the lavage fluid, which was identified as serum albumin. 4. Tandem mass spectrometry analysis of MDI-albumin revealed MDI conjugation occurs at a dilysine motif at Lys525, as well as at a glutamine-lysine motif at Lys414, in good agreement with previously published in vitro data on diisocyanate-conjugated serum albumin.

Human Development Inequality Index and Cancer Pattern: a Global Distributive Study.

PubMed

Rezaeian, Shahab; Khazaei, Salman; Khazaei, Somayeh; Mansori, Kamyar; Sanjari Moghaddam, Ali; Ayubi, Erfan

2016-01-01

This study aimed to quantify associations of the human development inequality (HDI) index with incidence, mortality, and mortality to incidence ratios for eight common cancers among different countries. In this ecological study, data about incidence and mortality rates of cancers was obtained from the Global Cancer Project for 169 countries. HDI indices for the same countries was obtained from the United Nations Development Program (UNDP) database. The concentration index was defined as the covariance between cumulative percentage of cancer indicators (incidence, mortality and mortality to incidence ratio) and the cumulative percentage of economic indicators (country economic rank). Results indicated that incidences of cancers of liver, cervix and esophagus were mainly concentrated in countries with a low HDI index while cancers of lung, breast, colorectum, prostate and stomach were concentrated mainly in countries with a high HDI index. The same pattern was observed for mortality from cancer except for prostate cancer that was more concentrated in countries with a low HDI index. Higher MIRs for all cancers were more concentrated in countries with a low HDI index. It was concluded that patterns of cancer occurrence correlate with care disparities at the country level.

Global Prostate Cancer Incidence and Mortality Rates According to the Human Development Index.

PubMed

Khazaei, Salman; Rezaeian, Shahab; Ayubi, Erfan; Gholamaliee, Behzad; Pishkuhi, Mahin Ahmadi; Khazaei, Somayeh; Mansori, Kamyar; Nematollahi, Shahrzad; Sani, Mohadeseh; Hanis, Shiva Mansouri

2016-01-01

Prostate cancer (PC) is one of the leading causes of death, especially in developed countries. The human development index (HDI) and its dimensions seem correlated with incidence and mortality rates of PC. This study aimed to assess the association of the specific components of HDI (life expectancy at birth, education, gross national income per 1000 capita, health, and living standards) with burden indicators of PC worldwide. Information of the incidence and mortality rates of PC was obtained from the GLOBOCAN cancer project in year 2012 and data about the HDI 2013 were obtained from the World Bank database. The correlation between incidence, mortality rates, and the HDI parameters were assessed using STATA software. A significant inequality of PC incidence rates was observed according to concentration indexes=0.25 with 95% CI (0.22, 0.34) and a negative mortality concentration index of -0.04 with 95% CI (-0.09, 0.01) was observed. A positive significant correlation was detected between the incidence rates of PC and the HDI and its dimensions including life expectancy at birth, education, income, urbanization level and obesity. However, there was a negative significant correlation between the standardized mortality rates and the life expectancy, income and HDI.

Progression of Mortality due to Diseases of the Circulatory System and Human Development Index in Rio de Janeiro Municipalities

PubMed Central

Soares, Gabriel Porto; Klein, Carlos Henrique; Silva, Nelson Albuquerque de Souza e; de Oliveira, Glaucia Maria Moraes

2016-01-01

Background Diseases of the circulatory system (DCS) are the major cause of death in Brazil and worldwide. Objective To correlate the compensated and adjusted mortality rates due to DCS in the Rio de Janeiro State municipalities between 1979 and 2010 with the Human Development Index (HDI) from 1970 onwards. Methods Population and death data were obtained in DATASUS/MS database. Mortality rates due to ischemic heart diseases (IHD), cerebrovascular diseases (CBVD) and DCS adjusted by using the direct method and compensated for ill-defined causes. The HDI data were obtained at the Brazilian Institute of Applied Research in Economics. The mortality rates and HDI values were correlated by estimating Pearson linear coefficients. The correlation coefficients between the mortality rates of census years 1991, 2000 and 2010 and HDI data of census years 1970, 1980 and 1991 were calculated with discrepancy of two demographic censuses. The linear regression coefficients were estimated with disease as the dependent variable and HDI as the independent variable. Results In recent decades, there was a reduction in mortality due to DCS in all Rio de Janeiro State municipalities, mainly because of the decline in mortality due to CBVD, which was preceded by an elevation in HDI. There was a strong correlation between the socioeconomic indicator and mortality rates. Conclusion The HDI progression showed a strong correlation with the decline in mortality due to DCS, signaling to the relevance of improvements in life conditions. PMID:27849263

Progression of Mortality due to Diseases of the Circulatory System and Human Development Index in Rio de Janeiro Municipalities.

PubMed

Soares, Gabriel Porto; Klein, Carlos Henrique; Silva, Nelson Albuquerque de Souza E; Oliveira, Glaucia Maria Moraes de

2016-10-01

Diseases of the circulatory system (DCS) are the major cause of death in Brazil and worldwide. To correlate the compensated and adjusted mortality rates due to DCS in the Rio de Janeiro State municipalities between 1979 and 2010 with the Human Development Index (HDI) from 1970 onwards. Population and death data were obtained in DATASUS/MS database. Mortality rates due to ischemic heart diseases (IHD), cerebrovascular diseases (CBVD) and DCS adjusted by using the direct method and compensated for ill-defined causes. The HDI data were obtained at the Brazilian Institute of Applied Research in Economics. The mortality rates and HDI values were correlated by estimating Pearson linear coefficients. The correlation coefficients between the mortality rates of census years 1991, 2000 and 2010 and HDI data of census years 1970, 1980 and 1991 were calculated with discrepancy of two demographic censuses. The linear regression coefficients were estimated with disease as the dependent variable and HDI as the independent variable. In recent decades, there was a reduction in mortality due to DCS in all Rio de Janeiro State municipalities, mainly because of the decline in mortality due to CBVD, which was preceded by an elevation in HDI. There was a strong correlation between the socioeconomic indicator and mortality rates. The HDI progression showed a strong correlation with the decline in mortality due to DCS, signaling to the relevance of improvements in life conditions.

A casein diet added isoflavone-enriched soy protein favorably affects biomarkers of steatohepatitis in obese Zucker rats.

PubMed

Gudbrandsen, Oddrun Anita; Wergedahl, Hege; Berge, Rolf Kristian

2009-05-01

Dietary supplementation of a soy protein enriched with isoflavones (HDI) has been shown to improve fatty liver in obese rats. The main objective of this study was to investigate whether HDI would influence the inflammatory status in livers of obese rats with fatty liver. Male obese Zucker fa/fa rats were fed casein (controls) or casein supplemented with HDI (containing 4.00 g of genistein and 4.50 g of daidzein per kilogram of diet) for 6 wk. The HDI-fed rats had a markedly lower hepatic concentration of triacylglycerol when compared with controls. The decreased aspartate transaminase/alanine transaminase ratio in plasma, together with lower circulating levels of alkaline phosphatase and bile acids after HDI feeding, implied an improved hepatitis. This was supported by decreased plasma and hepatic mRNA levels of tumor necrosis factor-alpha, lower plasma levels of interleukin-1beta and monocyte chemoattractant protein-1, and an increased anti-inflammatory fatty acid index in plasma. HDI also seemed to protect the rats from oxidative damage, because the level of lipid peroxides in triacylglycerol-rich lipoproteins after in vitro copper oxidation was lower for HDI-fed rats when compared with controls. These results show that isoflavone-enriched soy protein favorably affects biomarkers of hepatic inflammation in obese Zucker fa/fa rats with fatty liver. Thus, dietary soy proteins enriched in isoflavones may be a promising agent to improve steatohepatitis in patients.

Development of a fast curing tissue adhesive for meniscus tear repair.

PubMed

Bochyńska, Agnieszka Izabela; Hannink, Gerjon; Janssen, Dennis; Buma, Pieter; Grijpma, Dirk W

2017-01-01

Isocyanate-terminated adhesive amphiphilic block copolymers are attractive materials to treat meniscus tears due to their tuneable mechanical properties and good adhesive characteristics. However, a drawback of this class of materials is their relatively long curing time. In this study, we evaluate the use of an amine cross-linker and addition of catalysts as two strategies to accelerate the curing rates of a recently developed biodegradable reactive isocyanate-terminated hyper-branched adhesive block copolymer prepared from polyethylene glycol (PEG), trimethylene carbonate, citric acid and hexamethylene diisocyanate. The curing kinetics of the hyper-branched adhesive alone and in combination with different concentrations of spermidine solutions, and after addition of 2,2-dimorpholinodiethylether (DMDEE) or 1,4-diazabicyclo [2.2.2] octane (DABCO) were determined using FTIR. Additionally, lap-shear adhesion tests using all compositions at various time points were performed. The two most promising compositions of the fast curing adhesives were evaluated in a meniscus bucket handle lesion model and their performance was compared with that of fibrin glue. The results showed that addition of both spermidine and catalysts to the adhesive copolymer can accelerate the curing rate and that firm adhesion can already be achieved after 2 h. The adhesive strength to meniscus tissue of 3.2-3.7 N was considerably higher for the newly developed compositions than for fibrin glue (0.3 N). The proposed combination of an adhesive component and a cross-linking component or catalyst is a promising way to accelerate curing rates of isocyanate-terminated tissue adhesives.

Spatial durbin error model for human development index in Province of Central Java.

NASA Astrophysics Data System (ADS)

Septiawan, A. R.; Handajani, S. S.; Martini, T. S.

2018-05-01

The Human Development Index (HDI) is an indicator used to measure success in building the quality of human life, explaining how people access development outcomes when earning income, health and education. Every year HDI in Central Java has improved to a better direction. In 2016, HDI in Central Java was 69.98 %, an increase of 0.49 % over the previous year. The objective of this study was to apply the spatial Durbin error model using angle weights queen contiguity to measure HDI in Central Java Province. Spatial Durbin error model is used because the model overcomes the spatial effect of errors and the effects of spatial depedency on the independent variable. Factors there use is life expectancy, mean years of schooling, expected years of schooling, and purchasing power parity. Based on the result of research, we get spatial Durbin error model for HDI in Central Java with influencing factors are life expectancy, mean years of schooling, expected years of schooling, and purchasing power parity.

Human Disease Insight: An integrated knowledge-based platform for disease-gene-drug information.

PubMed

Tasleem, Munazzah; Ishrat, Romana; Islam, Asimul; Ahmad, Faizan; Hassan, Md Imtaiyaz

2016-01-01

The scope of the Human Disease Insight (HDI) database is not limited to researchers or physicians as it also provides basic information to non-professionals and creates disease awareness, thereby reducing the chances of patient suffering due to ignorance. HDI is a knowledge-based resource providing information on human diseases to both scientists and the general public. Here, our mission is to provide a comprehensive human disease database containing most of the available useful information, with extensive cross-referencing. HDI is a knowledge management system that acts as a central hub to access information about human diseases and associated drugs and genes. In addition, HDI contains well-classified bioinformatics tools with helpful descriptions. These integrated bioinformatics tools enable researchers to annotate disease-specific genes and perform protein analysis, search for biomarkers and identify potential vaccine candidates. Eventually, these tools will facilitate the analysis of disease-associated data. The HDI provides two types of search capabilities and includes provisions for downloading, uploading and searching disease/gene/drug-related information. The logistical design of the HDI allows for regular updating. The database is designed to work best with Mozilla Firefox and Google Chrome and is freely accessible at http://humandiseaseinsight.com. Copyright © 2015 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

National HIV/AIDS mortality, prevalence, and incidence rates are associated with the Human Development Index.

PubMed

Lou, Li-Xia; Chen, Yi; Yu, Chao-Hui; Li, You-Ming; Ye, Juan

2014-10-01

HIV/AIDS is a worldwide threat to human health with mortality, prevalence, and incidence rates varying widely. We evaluated the association between the global HIV/AIDS epidemic and national socioeconomic development. We obtained global age-standardized HIV/AIDS mortality, prevalence, and incidence rates from World Health Statistics Report of the World Health Organization. The human development indexes (HDIs) of 141 countries were obtained from a Human Development Report. Countries were divided into 4 groups according to the HDI distribution. We explored the association between HIV/AIDS epidemic and HDI information using Spearman correlation analysis, regression analysis, and the Kruskal-Wallis test. HIV/AIDS mortality, prevalence, and incidence rates were inversely correlated with national HDI (r = -0.675, -0.519, and -0.398, respectively; P < .001), as well as the 4 indicators of HDI (ie, life expectancy at birth, mean years of schooling, expected years of schooling, and gross national income per capita). Low HDI countries had higher HIV/AIDS mortality, prevalence, and incidence rates than that of medium, high, and very high HDI countries. Quantile regression results indicated that HDI had a greater negative effect on the HIV/AIDS epidemic in countries with more severe HIV/AIDS epidemic. Less-developed countries are likely to have more severe HIV/AIDS epidemic. There is a need to pay more attention to HIV/AIDS control in less-developed countries, where lower socioeconomic status might have accelerated the HIV/AIDS epidemic more rapidly. Copyright © 2014 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Inequalities in cancer incidence and mortality across medium to highly developed countries in the twenty-first century.

PubMed

Arnold, Melina; Rentería, Elisenda; Conway, David I; Bray, Freddie; Van Ourti, Tom; Soerjomataram, Isabelle

2016-08-01

Inequalities in the burden of cancer have been well documented, and a variety of measures exist to analyse disease disparities. While previous studies have focused on inequalities within countries, the aim of the present study was to quantify existing inequalities in cancer incidence and mortality between countries. Data on total and site-specific cancer incidence and mortality in 2003-2007 were obtained for 43 countries with medium-to-high levels of human development via Cancer Incidence in Five Continents Vol. X and the WHO Mortality Database. We calculated the concentration index as a summary measure of socioeconomic-related inequality between countries. Inequalities in cancer burden differed markedly by site; the concentration index for all sites combined was 0.03 for incidence and 0.02 for mortality, pointing towards a slightly higher burden in countries with higher levels of the human development index (HDI). For both incidence and mortality, this pattern was most pronounced for melanoma. In contrast, the burden of cervical cancer was disproportionally high in countries with lower HDI levels. Prostate, lung and breast cancer contributed most to inequalities in overall cancer incidence in countries with higher HDI levels, while for mortality these were mostly driven by lung cancer in higher HDI countries and stomach cancer in countries with lower HDI levels. Global inequalities in the burden of cancer remain evident at the beginning of the twenty-first century: with a disproportionate burden of lifestyle-related cancers in countries classified as high HDI, while infection-related cancers continue to predominate in transitioning countries with lower levels of HDI.

Incidence and mortality of kidney cancers, and human development index in Asia; a matter of concern.

PubMed

Arabsalmani, Masoumeh; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Hadadian, Fatemeh; Towhidi, Farhad; Vafaee, Kamran; Salehiniya, Hamid

2017-01-01

The incidence and mortality of kidney cancer have steadily increased by 2%- 3% per decade worldwide, and an increased risk of kidney cancer has been observed in many Asian countries. The information on the incidence and mortality of a disease and its distribution is essential for better planning for prevention and further studies. This study aimed to assess the incidence and mortality of kidney cancer and their correlation with the human development index (HDI) in Asia. This ecological study was based on GLOBOCAN data Asia for assessment the correlation between age-specific incidence rate (ASIR) and age-specific mortality rate (ASMR) with HDI and its details that include life expectancy at birth, mean years of schooling and gross national income (GNI) per capita. We use of correlation bivariate method for assessment the correlation between ASIR and ASMR with HDI and its components. A total of 121 099 kidney cancer cases were recorded in Asian countries in 2012.Overall, 80 080 cases (66.12%) were males. Sex ratio was 1.95. The three countries with the highest number of new patients were china (66 466 cases), Japan (16 830 cases), India(9658 cases), respectively. Positive correlation were seen between HDI and ASIR of kidney cancer 0.655 ( P = 0.001), and HDI and ASMR of kidney cancer 0.285 ( P = 0.055). A positive relationship between ASIR and the HDI was seen. The relationship is due to risk factors in countries with high development such as older age, smoking, hypertension, obesity, and diet. However, ASMR showed no significant relationship with HDI.

Shifting the Physical Inactivity Curve Worldwide by Closing the Gender Gap.

PubMed

Mielke, Grégore I; da Silva, Inacio Crochemore M; Kolbe-Alexander, Tracy L; Brown, Wendy J

2018-02-01

The aims of this study were to (i) examine gender differences in physical inactivity in countries with different levels of Human Development Index (HDI); and (ii) assess whether small changes in the prevalence of inactivity in women could achieve the World Health Organization's (WHO) global inactivity target. Data on inactivity were extracted for 142 countries for the year 2010 from the WHO Data Repository. Data for HDI were obtained for the year 2010 from the United Nations Development Program. Absolute and relative gender differences were calculated for countries according to four HDI categories. The potential effects of increasing women's activity levels on achievement of the WHO physical inactivity target were computed. Overall inactivity prevalence was higher in women (27%) than in men (20%). Women were more inactive than men in all except eight countries. Absolute gender differences [median 7.5% (range -10.1 to 33.2)] did not vary by HDI category, but there was a small negative correlation between relative gender difference in inactivity and HDI (rho -0.19; p = 0.02), which was mostly influenced by three outlier countries with low HDI. A decrease in inactivity levels of 4.8% points among women across the world would achieve the WHO target of reducing global levels of inactivity by 10%. Gender differences in the prevalence of physical inactivity were highly variable, both within and across categories of HDI. Interventions which result in small changes in inactivity prevalence in women would achieve the 2025 WHO global target for inactivity, without any change to the prevalence in men.

Incidence and Mortality of Breast Cancer and their Relationship with the Human Development Index (HDI) in the World in 2012.

PubMed

Ghoncheh, Mahshid; Mirzaei, Maryam; Salehiniya, Hamid

2015-01-01

Breast cancer is the most common malignancy in women worldwide and its incidence is generally increasing. In 2012, it was the second most common cancer in the world. It is necessary to obtain information on incidence and mortality for health planning. This study aimed to investigate the relationship between the human development index (HDI), and the incidence and mortality rates of breast cancer in the world in 2012. This ecologic study concerns incidence rate and standardized mortality rates of the cancer from GLOBOCAN in 2012, and HDI and its components extracted from the global bank site. Data were analyzed using correlation tests and regression with SPSS software (version 15). Among the six regions of WHO, the highest breast cancer incidence rate (67.6) was observed in the PAHO, and the lowest incidence rate was 27.8 for SEARO. There was a direct, strong, and meaningful correlation between the standardized incidence rate and HDI (r=0.725, p≤0.001). Pearson correlation test showed that there was a significant correlation between age-specific incidence rate (ASIR) and components of the HDI (life expectancy at birth, mean years of schooling, and GNP). On the other, a non-significant relationship was observed between ASIR and HDI overall (r=0.091, p=0.241). In total, a significant relationship was not found between age-specific mortality rate (ASMR) and components of HDI. Significant positive correlations exist between ASIR and components of the HDI. Socioeconomic status is directly related to the stage of the cancer and patient's survival. With increasing the incidence rate of the cancer, mortality rate from the cancer does not necessariloy increase. This may be due to more early detection and treatment in developed that developing countries. It is necessary to increase awareness of risk factors and early detection in the latter.

Vapor Pressure of Hexamethylene Triperoxide Diamine (HTMD) Determined with Secondary Electrospray Ionization Mass Spectrometry

DTIC Science & Technology

2015-07-03

peroxide-based explosive hexamethylene triperoxide diamine (HMTD) over the temperature range of 301 – 353°K (28-80° C ). The method utilizes a...Air Force Contract #FA8721-05- C -0002. Opinions, interpretations, recommendations, and conclusions are those of the authors and are not necessarily...and carbon dioxide observed as the primary HMTD decomposition products at temperatures ° C [3]. A later study aimed at determining the vapor

Detection of diisocyanates in nesting material associated with mortality in pigeon chicks.

PubMed

Mukai, Motoko; Woods, Leslie W; Stump, Samuel; Ebel, Joseph G; Levitt, Ariana S; Frey, Margaret W; Smith, Jeanne; Uzal, Francisco A; Poppenga, Robert H; Puschner, Birgit

2014-03-01

Diisocyanates, commonly used in the production of polyurethane foams, paints, elastomers, varnishes, and coatings, are considered among the most hazardous inhalation toxicants. The present report describes 2 unusual cases of mortality in pigeon chicks associated with nesting material contaminated by diisocyanates. Case 1 was submitted by a racing pigeon breeder who had lost all the hatchlings (n = 125) following replacement of the nesting material with a different lot. All adult birds appeared healthy, and hatchability was not significantly affected, but hatchlings became lethargic and dyspneic after a day of hatch. At necropsy, dark wet lungs were found in the hatchlings. Case 2 was submitted by a show-roller pigeon breeder. In this case, the owner reported lower hatchability, and all hatchlings (approximately 100) died within 2 days of hatching with clinical signs similar to the first case. Necropsy did not reveal any significant findings. For both cases, nesting materials were screened for toxic compounds using gas chromatography-mass spectrometry. Toluene-2,4-diisocyanate (approximately 190-290 ppm) and 4,4'-methylene diphenyl diisocyanate (unquantified) were detected in the nesting pads. While there is very limited information on toxicosis in birds, there are reports of inhalant exposure of diisocyanates causing pulmonary edema and death in various mammalian species. Although cause-effect relationship of mortality and the nesting material was not established in the present cases, the presence of toxic compounds in the nesting materials is a cause for concern. Further investigation is needed to determine the prevalence and toxicity of diisocyanates-contaminated nesting material in avian species.

Anesthesia-Related and Perioperative Cardiac Arrest in Low- and High-Income Countries: A Systematic Review With Meta-Regression and Proportional Meta-Analysis.

PubMed

Koga, Fernando A; El Dib, Regina; Wakasugui, William; Roça, Cairo T; Corrente, José E; Braz, Mariana G; Braz, José R C; Braz, Leandro G

2015-09-01

The anesthesia-related cardiac arrest (CA) rate is a quality indicator to improve patient safety in the perioperative period. A systematic review with meta-analysis of the worldwide literature related to anesthesia-related CA rate has not yet been performed.This study aimed to analyze global data on anesthesia-related and perioperative CA rates according to country's Human Development Index (HDI) and by time. In addition, we compared the anesthesia-related and perioperative CA rates in low- and high-income countries in 2 time periods.A systematic review was performed using electronic databases to identify studies in which patients underwent anesthesia with anesthesia-related and/or perioperative CA rates. Meta-regression and proportional meta-analysis were performed with 95% confidence intervals (CIs) to evaluate global data on anesthesia-related and perioperative CA rates according to country's HDI and by time, and to compare the anesthesia-related and perioperative CA rates by country's HDI status (low HDI vs high HDI) and by time period (pre-1990s vs 1990s-2010s), respectively.Fifty-three studies from 21 countries assessing 11.9 million anesthetic administrations were included. Meta-regression showed that anesthesia-related (slope: -3.5729; 95% CI: -6.6306 to -0.5152; P = 0.024) and perioperative (slope: -2.4071; 95% CI: -4.0482 to -0.7659; P = 0.005) CA rates decreased with increasing HDI, but not with time. Meta-analysis showed per 10,000 anesthetics that anesthesia-related and perioperative CA rates declined in high HDI (2.3 [95% CI: 1.2-3.7] before the 1990s to 0.7 [95% CI: 0.5-1.0] in the 1990s-2010s, P < 0.001; and 8.1 [95% CI: 5.1-11.9] before the 1990s to 6.2 [95% CI: 5.1-7.4] in the 1990s-2010s, P < 0.001, respectively). In low-HDI countries, anesthesia-related CA rates did not alter significantly (9.2 [95% CI: 2.0-21.7] before the 1990s to 4.5 [95% CI: 2.4-7.2] in the 1990s-2010s, P = 0.14), whereas perioperative CA rates increased significantly (16.4 [95% CI: 1.5-47.1] before the 1990s to 19.9 [95% CI: 10.9-31.7] in the 1990s-2010s, P = 0.03).Both anesthesia-related and perioperative CA rates decrease with increasing HDI but not with time. There is a clear and consistent reduction in anesthesia-related and perioperative CA rates in high-HDI countries, but an increase in perioperative CA rates without significant alteration in the anesthesia-related CA rates in low-HDI countries comparing the 2 time periods.

Incidence and mortality of kidney cancers, and human development index in Asia; a matter of concern

PubMed Central

Arabsalmani, Masoumeh; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Hadadian, Fatemeh; Towhidi, Farhad; Vafaee, Kamran; Salehiniya, Hamid

2017-01-01

Background The incidence and mortality of kidney cancer have steadily increased by 2%- 3% per decade worldwide, and an increased risk of kidney cancer has been observed in many Asian countries. The information on the incidence and mortality of a disease and its distribution is essential for better planning for prevention and further studies. Objectives This study aimed to assess the incidence and mortality of kidney cancer and their correlation with the human development index (HDI) in Asia. Materials and Methods This ecological study was based on GLOBOCAN data Asia for assessment the correlation between age-specific incidence rate (ASIR) and age-specific mortality rate (ASMR) with HDI and its details that include life expectancy at birth, mean years of schooling and gross national income (GNI) per capita. We use of correlation bivariate method for assessment the correlation between ASIR and ASMR with HDI and its components. Results A total of 121 099 kidney cancer cases were recorded in Asian countries in 2012.Overall, 80 080 cases (66.12%) were males. Sex ratio was 1.95. The three countries with the highest number of new patients were china (66 466 cases), Japan (16 830 cases), India(9658 cases), respectively. Positive correlation were seen between HDI and ASIR of kidney cancer 0.655 (P = 0.001), and HDI and ASMR of kidney cancer 0.285 (P = 0.055). Conclusions A positive relationship between ASIR and the HDI was seen. The relationship is due to risk factors in countries with high development such as older age, smoking, hypertension, obesity, and diet. However, ASMR showed no significant relationship with HDI. PMID:28042551

Incidence and Mortality of Breast Cancer and their Relationship to Development in Asia.

PubMed

Ghoncheh, Mahshid; Mohammadian-Hafshejani, Abdollah; Salehiniya, Hamid

2015-01-01

This study aimed to investigate the incidence and mortality of breast cancer, and its relationship with human development index (HDI) and its components in Asia in 2012. This study was an ecologic study in Asia for assessment of the correlation between age-specific incidence rate (ASIR) and age-specific mortality rate (ASMR) with HDI and its details that include: life expectancy at birth, mean years of schooling and gross national income (GNI) per capita. Data about SIR and SMR for every Asian country for the year 2012 were obtained from the global cancer project. We used a bivariate method for assessment of the correlation between SIR and SMR and HDI and its individual components. Statistical significance was assumed if P<0.05. All reported P-values are two-sided. Statistical analyses were performed using SPSS (Version 15.0, SPSS Inc.). In 2012, 639,824 cases of breast cancer were recorded in Asian countries. Countries with the highest standardized incidence rate (ASIR) (per 100,000) were Israel (80.5), Lebanon (78.7), Armenia (74.1) and the highest standard mortality rate (ASMR) was observed in Pakistan (25.2), Armenia (24.2), and Lebanon (24). There was a positive correlation between the ASIR of breast cancer and HDI (r = 0.556, p <0.001), whereas there was a negative correlation between the ASMR of breast cancer and HDI (r = -0.051). Breast cancer incidence in countries with higher development is greater, while mortality is greatest in countries with less development. There was a positive and significant relationship between the ASIR of breast cancer and HDI and its components. Also there was a negative but non significant relationship between the ASMR of breast cancer and HDI.

Early childhood development: impact of national human development, family poverty, parenting practices and access to early childhood education.

PubMed

Tran, T D; Luchters, S; Fisher, J

2017-05-01

This study was to describe and quantify the relationships among family poverty, parents' caregiving practices, access to education and the development of children living in low- and middle-income countries (LAMIC). We conducted a secondary analysis of data collected in UNICEF's Multiple Indicator Cluster Surveys (MICS). Early childhood development was assessed in four domains: language-cognitive, physical, socio-emotional and approaches to learning. Countries were classified into three groups on the basis of the Human Development Index (HDI). Overall, data from 97 731 children aged 36 to 59 months from 35 LAMIC were included in the after analyses. The mean child development scale score was 4.93 out of a maximum score of 10 (95%CI 4.90 to 4.97) in low-HDI countries and 7.08 (95%CI 7.05 to 7.12) in high-HDI countries. Family poverty was associated with lower child development scores in all countries. The total indirect effect of family poverty on child development score via attending early childhood education, care for the child at home and use of harsh punishments at home was -0.13 SD (77.8% of the total effect) in low-HDI countries, -0.09 SD (23.8% of the total effect) in medium-HDI countries and -0.02 SD (6.9% of the total effect) in high-HDI countries. Children in the most disadvantaged position in their societies and children living in low-HDI countries are at the greatest risk of failing to reach their developmental potential. Optimizing care for child development at home is essential to reduce the adverse effects of poverty on children's early development and subsequent life. © 2016 John Wiley & Sons Ltd.

Technical Summary of the Half-Degree Imager (HDI)

NASA Astrophysics Data System (ADS)

Richmond, Michael W.

2017-01-01

The Half-Degree Imager (HDI) was first attached to the WIYN 0.9-m Telescope in October, 2013. In the three years since then, it has served a large community of astronomers throughout the WIYN 0.9-m consortium. The large field of view and relatively short readout time, combined with a large selection of broad-band and narrow-band filters, make HDI a powerful tool for large-area surveys. I will provide a summary of the technical features of this CCD camera and its operations, and present statistics on its use -- showing the fraction of time lost due to bad weather and technical problems. I will reserve time to answer questions from the audience, including those who may be interested in using HDI for their own projects.

Benchmarking life expectancy and cancer mortality: global comparison with cardiovascular disease 1981-2010

PubMed Central

Bray, Freddie; Beltrán-Sánchez, Hiram; Ginsburg, Ophira; Soneji, Samir; Soerjomataram, Isabelle

2017-01-01

Objective To quantify the impact of cancer (all cancers combined and major sites) compared with cardiovascular disease (CVD) on longevity worldwide during 1981-2010. Design Retrospective demographic analysis using aggregated data. Setting National civil registration systems in member states of the World Health Organization. Participants 52 populations with moderate to high quality data on cause specific mortality. Main outcome measures Disease specific contributions to changes in life expectancy in ages 40-84 (LE40-84) over time in populations grouped by two levels of Human Development Index (HDI) values. Results Declining CVD mortality rates during 1981-2010 contributed to, on average, over half of the gains in LE40-84; the corresponding gains were 2.3 (men) and 1.7 (women) years, and 0.5 (men) and 0.8 (women) years in very high and medium and high HDI populations, respectively. Declines in cancer mortality rates contributed to, on average, 20% of the gains in LE40-84, or 0.8 (men) and 0.5 (women) years in very high HDI populations, and to over 10% or 0.2 years (both sexes) in medium and high HDI populations. Declining lung cancer mortality rates brought about the largest LE40-84 gain in men in very high HDI populations (up to 0.7 years in the Netherlands), whereas in medium and high HDI populations its contribution was smaller yet still positive. Among women, declines in breast cancer mortality rates were largely responsible for the improvement in longevity, particularly among very high HDI populations (up to 0.3 years in the United Kingdom). In contrast, losses in LE40-84 were observed in many medium and high HDI populations as a result of increasing breast cancer mortality rates. Conclusions The control of CVD has led to substantial gains in LE40-84 worldwide. The inequality in improvement in longevity attributed to declining cancer mortality rates reflects inequities in implementation of cancer control, particularly in less resourced populations and in women. Global actions are needed to revitalize efforts for cancer control, with a specific focus on less resourced countries. PMID:28637656

Energy expenditure in adults living in developing compared with industrialized countries: a meta-analysis of doubly labeled water studies123

PubMed Central

Dugas, Lara R; Harders, Regina; Merrill, Sarah; Ebersole, Kara; Shoham, David A; Rush, Elaine C; Assah, Felix K; Forrester, Terrence; Durazo-Arvizu, Ramon A; Luke, Amy

2011-01-01

Background: There is an assumption that people in developing countries have a higher total energy expenditure (TEE) and physical activity level (PAL) than do people in developed nations, but few objective data for this assertion exist. Objective: We conducted a meta-analysis of TEE and PAL by using data from countries that have a low or middle human development index (HDI) compared with those with a high HDI to better understand how energy-expenditure variables are associated with development status and population differences in body size. Design: We performed a literature search for studies in which energy expenditure was measured by using doubly labeled water. Mean data on age, weight, body mass index (BMI; in kg/m2), TEE, and PAL were extracted, and HDI status was assessed. Pooled estimates of the mean effect by sex were obtained, and the extent to which age, weight, HDI status, and year of publication explained heterogeneity was assessed. Results: A total of 98 studies (14 studies from low- or middle-HDI countries) that represented 183 cohorts and 4972 individuals were included. Mean (±SE) BMI was lower in countries with a low or middle HDI than in those with a high HDI for both men and women (22.7 ± 1.0 compared with 26.0 ± 0.7, respectively, in men and 24.3 ± 0.7 compared with 26.6 ± 0.4, respectively, in women). In meta-regression models, there was an inverse association of age (P < 0.001) and a positive association of weight (P < 0.001) with TEE for both sexes; there was an association of age only in men with PAL (P < 0.001). There was no association of HDI status with either TEE or PAL. Conclusion: TEE adjusted for weight and age or PAL did not differ significantly between developing and industrialized countries, which calls into question the role of energy expenditure in the cause of obesity at the population level. PMID:21159791

Incidence and Mortality of Testicular Cancer and Relationships with Development in Asia.

PubMed

Sadeghi, Mostafa; Ghoncheh, Mahshid; Mohammadian-Hafshejani, Abdollah; Gandomani, Hamidreza Sadeghi; Rafiemanesh, Hosein; Salehiniya, Hamid

2016-01-01

Testicular cancer is one of the most common cancers among young men between ages 20-34 in countries with high or very high levels of the Human Development Index (HDI). This study investigated the incidence and mortality of prostate cancer and the relationship with the HDI and its dimensions in Asia in 2012. The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). Standardized incidence and mortality rates of testicular cancer were calculated for Asian countries. Correlations between incidence and/ormortality rates, and the HDI and its components were assessed with the use of the correlation test, using SPSS software. There was a total of 14902 incidences and 5832 death were recorded in Asian countries in 2012. Among the Asian countries, the five countries with the highest standardized incidence rates of testicular cancer were Israel, Georgia, Turkey, Lebanon and Kazakhstan and the five countries with the highest standardized mortality rates were Turkey, Georgia, Jordan, Cambodia and the Syrian Arab Republic. A positive correlation of 0.382 was observed between the standardized incidence rates of testicular cancer and the HDI (p=0.009). Also a negative correlation of 0.298 between the standardized mortality rate of testicular cancer and the Human Development Index was noted although this relation was statistically non-significant (p=0.052). There is a positive correlation between HDI and the standardized incidence rate of testicular cancer and negative correlation with standardized mortality rate.

Toluene Diisocyanates (TDI) Action Plan

EPA Pesticide Factsheets

This Action Plan addresses the use of toluene diisocyanate (TDI) and related compounds in products that may result in consumer and general population exposures, particularly in or around buildings, including homes and schools.

The modifying influence of country development on the effect of individual educational attainment on self-rated health.

PubMed

van der Kooi, Anne L F; Stronks, Karien; Thompson, Caroline A; DerSarkissian, Maral; Arah, Onyebuchi A

2013-11-01

We investigated how much the Human Development Index (HDI), a global measure of development, modifies the effect of education on self-reported health. We analyzed cross-sectional World Health Survey data on 217,642 individuals from 49 countries, collected in 2002 to 2005, with random-intercept multilevel linear regression models. We observed greater positive associations between educational levels and self-reported good health with increasing HDI. The magnitude of this effect modification of the education-health relation tended to increase with educational attainment. For example, before adjustment for effect modification, at comparable HDI, on average, finishing primary school was associated with better general health (b = 1.49; 95% confidence interval [CI] = 1.18, 1.80). With adjustment for effect modification by HDI, the impact became 4.63 (95% CI = 3.63, 5.62) for every 0.1 increase in HDI. Among those who completed high school, these associations were, respectively, 5.59 (95% CI = 5.20, 5.98) and 9.95 (95% CI = 8.89, 11.00). The health benefits of educational attainment are greater in countries with greater human development. Health inequalities attributable to education are, therefore, larger in more developed countries.

Emerging correlations between measures of population well-being, suicide and homicide: a look at global and Australian data.

PubMed

Lee, Adrian Ys; Pridmore, Saxby

2014-04-01

Our aim was (1) to examine global and Australian data with a view to determining the presence of an inverse relationship between suicide and homicide rates, and (2) to examine global Human Development Index (HDI) values and suicide and homicide rates, with a view to determining any statistical relationship. Suicide and homicide rates and HDI values were available for 102 countries, and suicide and homicide rates were available for the states and territories of Australia. The three data sets had non-normal distributions, and the non-parametric Spearman's ρ was used for correlation statistics with α = 0.05. We found a weak, statistically significant inverse relationship between the suicide and homicide rates of 102 countries (ρ = -0.244, p = 0.014). No relationship was established for the Australian values, however. As anticipated, we found a significant negative correlation between homicide and HDI values. We unexpectedly demonstrated a positive correlation between suicide rates and HDI values. The notion that suicide and homicide have an inverse relationship now has some scientific support; but additional research is warranted to characterise and explain this relationship. The unexpected finding of a positive correlation between suicide rates and HDI values requires further examination.

Socioeconomic status is associated with global diabetes prevalence

PubMed Central

Xu, Zhiye; Yu, Dan; Yin, Xueyao; Zheng, Fenping; Li, Hong

2017-01-01

The incidence of diabetes is increasing globally. We investigated the relationship between diabetes prevalence and patient socioeconomic status across multiple countries. We searched PubMed to identify population-based surveys reporting diabetes prevalence between 1990 and May 2016. Search results were filtered, and Human Development Index (HDI) values from the United Nations Development Programme were used to assess socioeconomic status for a given nation. Our analysis included 45 national surveys from 32 countries. Diabetes prevalence was positively correlated with national HDI (r = 0.421 P = 0.041) in developing countries, and negatively correlated with HDI (r = −0.442 P = 0.045) in developed countries. Diabetes prevalence trends were the same in women and men, although men were associated with increased diabetes risk in developed countries (r = 0.459 P = 0.048). Thus, diabetes prevalence rises with increasing HDI in developing countries, and this is reversed in developed countries. Ours is the first study to investigate the relationship between diabetes and socioeconomic status at global level using HDI values. These results will aid in evaluating global diabetes prevalence and risk with respect to patient socioeconomic status, and will be useful in the development of policies that help reduce disease incidence. PMID:28574844

Socioeconomic status is associated with global diabetes prevalence.

PubMed

Xu, Zhiye; Yu, Dan; Yin, Xueyao; Zheng, Fenping; Li, Hong

2017-07-04

The incidence of diabetes is increasing globally. We investigated the relationship between diabetes prevalence and patient socioeconomic status across multiple countries. We searched PubMed to identify population-based surveys reporting diabetes prevalence between 1990 and May 2016. Search results were filtered, and Human Development Index (HDI) values from the United Nations Development Programme were used to assess socioeconomic status for a given nation. Our analysis included 45 national surveys from 32 countries. Diabetes prevalence was positively correlated with national HDI (r = 0.421 P = 0.041) in developing countries, and negatively correlated with HDI (r = -0.442 P = 0.045) in developed countries. Diabetes prevalence trends were the same in women and men, although men were associated with increased diabetes risk in developed countries (r = 0.459 P = 0.048). Thus, diabetes prevalence rises with increasing HDI in developing countries, and this is reversed in developed countries. Ours is the first study to investigate the relationship between diabetes and socioeconomic status at global level using HDI values. These results will aid in evaluating global diabetes prevalence and risk with respect to patient socioeconomic status, and will be useful in the development of policies that help reduce disease incidence.

The effect of compound 48/80 on contractions induced by toluene diisocyanate in isolated guinea-pig bronchus.

PubMed

Mapp, C E; Boniotti, A; Papi, A; Chitano, P; Coser, E; Di Stefano, A; Saetta, M; Ciaccia, A; Fabbri, L M

1993-06-01

We have investigated the ability of compound 48/80 and of histamine H1 and H2 receptor antagonists to inhibit toluene diisocyanate-induced contractions in isolated guinea-pig bronchi. Compound 48/80 (100 micrograms/ml) significantly inhibited toluene diisocyanate-induced contractions. By contrast, the two histamine H1 and H2 receptor antagonists, chlorpheniramine (10 microM) and cimetidine, (10 microM) did not affect toluene diisocyanate-induced contractions, but significantly inhibited contractions induced by exogenously applied histamine (100 microM) and by 48/80. We investigated which mechanisms 48/80 used to inhibit toluene diisocyanate-induced contractions, paying particular attention to the possible involvement of capsaicin-sensitive primary afferents. In vitro capsaicin desensitization (10 microM for 30 min followed by washing) significantly reduced compound 48/80-induced contractions. A capsaicin-resistant component of contraction was also evident. Ruthenium red (3 microM), an inorganic dye which acts as a selective functional antagonist of capsaicin, did not affect 48/80-induced contraction. MEN 10,207 (Tyr5,D-Trp6,8,9,Arg10)-neurokinin A (4-10) (3 microM) a selective antagonist of NK2-tachykinin receptors significantly reduced 48/80-induced contractions. These results show that compound 48/80 inhibits toluene diisocyanate-induced contractions in isolated guinea-pig bronchi. It is likely that two mechanisms are involved in the inhibition: (1) the release of mediators other than histamine by mast cells, (2) an effect of 48/80 on sensory nerves.

A human development framework for CO2 reductions.

PubMed

Costa, Luís; Rybski, Diego; Kropp, Jürgen P

2011-01-01

Although developing countries are called to participate in CO(2) emission reduction efforts to avoid dangerous climate change, the implications of proposed reduction schemes in human development standards of developing countries remain a matter of debate. We show the existence of a positive and time-dependent correlation between the Human Development Index (HDI) and per capita CO(2) emissions from fossil fuel combustion. Employing this empirical relation, extrapolating the HDI, and using three population scenarios, the cumulative CO(2) emissions necessary for developing countries to achieve particular HDI thresholds are assessed following a Development As Usual approach (DAU). If current demographic and development trends are maintained, we estimate that by 2050 around 85% of the world's population will live in countries with high HDI (above 0.8). In particular, 300 Gt of cumulative CO(2) emissions between 2000 and 2050 are estimated to be necessary for the development of 104 developing countries in the year 2000. This value represents between 20 % to 30 % of previously calculated CO(2) budgets limiting global warming to 2 °C. These constraints and results are incorporated into a CO(2) reduction framework involving four domains of climate action for individual countries. The framework reserves a fair emission path for developing countries to proceed with their development by indexing country-dependent reduction rates proportional to the HDI in order to preserve the 2 °C target after a particular development threshold is reached. For example, in each time step of five years, countries with an HDI of 0.85 would need to reduce their per capita emissions by approx. 17% and countries with an HDI of 0.9 by 33 %. Under this approach, global cumulative emissions by 2050 are estimated to range from 850 up to 1100 Gt of CO(2). These values are within the uncertainty range of emissions to limit global temperatures to 2 °C. © 2011 Costa et al.

The impact of human development on individual health: a causal mediation analysis examining pathways through education and body mass index.

PubMed

Wang, Aolin; Arah, Onyebuchi A

2017-01-01

The macro environment we live in projects what we can achieve and how we behave, and in turn, shapes our health in complex ways. Policymaking will benefit from insights into the mechanisms underlying how national socioeconomic context affects health. This study examined the impact of human development on individual health and the possible mediating roles of education and body mass index (BMI). We analyzed World Health Survey data on 109,448 participants aged 25 or older from 42 low- and middle-income countries with augmented human development index (HDI) in 1990. We used principal components method to create a health score based on measures from eight health state domains, used years of schooling as education indicator and calculated BMI from self-reported height and weight. We used causal mediation analysis technique with random intercepts to account for the multilevel structure. Below a reference HDI level of 0.48, HDI was negatively associated with good health (total effect at HDI of 0.23: b  =  - 3.44, 95% CI [-6.39--0.49] for males and b  =  - 5.16, 95% CI [-9.24,--1.08] for females) but was positively associated with good health above this reference level (total effect at HDI of 0.75: b  = 4.16, 95% CI [-0.33-8.66] for males and b  = 6.62, 95% CI [0.85-12.38] for females). We found a small positive effect of HDI on health via education across reference HDI levels ( b ranging from 0.24 to 0.29 for males and 0.40 to 0.49 for females) but not via pathways involving BMI only. Human development has a non-linear effect on individual health, but the impact appears to be mainly through pathways other than education and BMI.

A Human Development Framework for CO2 Reductions

PubMed Central

Costa, Luís; Rybski, Diego; Kropp, Jürgen P.

2011-01-01

Although developing countries are called to participate in CO2 emission reduction efforts to avoid dangerous climate change, the implications of proposed reduction schemes in human development standards of developing countries remain a matter of debate. We show the existence of a positive and time-dependent correlation between the Human Development Index (HDI) and per capita CO2 emissions from fossil fuel combustion. Employing this empirical relation, extrapolating the HDI, and using three population scenarios, the cumulative CO2 emissions necessary for developing countries to achieve particular HDI thresholds are assessed following a Development As Usual approach (DAU). If current demographic and development trends are maintained, we estimate that by 2050 around 85% of the world’s population will live in countries with high HDI (above 0.8). In particular, 300 Gt of cumulative CO2 emissions between 2000 and 2050 are estimated to be necessary for the development of 104 developing countries in the year 2000. This value represents between 20 % to 30 % of previously calculated CO2 budgets limiting global warming to 2°C. These constraints and results are incorporated into a CO2 reduction framework involving four domains of climate action for individual countries. The framework reserves a fair emission path for developing countries to proceed with their development by indexing country-dependent reduction rates proportional to the HDI in order to preserve the 2°C target after a particular development threshold is reached. For example, in each time step of five years, countries with an HDI of 0.85 would need to reduce their per capita emissions by approx. 17% and countries with an HDI of 0.9 by 33 %. Under this approach, global cumulative emissions by 2050 are estimated to range from 850 up to 1100 Gt of CO2. These values are within the uncertainty range of emissions to limit global temperatures to 2°C. PMID:22216227

The incidence and mortality of prostate cancer and its relationship with development in Asia

PubMed Central

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Pakzad, Iraj; Salehiniya, Hamid

2015-01-01

Purpose Prostate cancer is a common cancer in men in the world. It is rapidly increasing. This study investigated the incidence and mortality of prostate cancer and the relationship with the Human Development Index (HDI) and its dimensions in Asia in 2012. Methods The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). The standardized incidence and mortality rates of prostate cancer were calculated for Asian countries. The correlation between incidence, mortality rates, and the HDI and its components were assessed with the use of the correlation test, using SPSS software. Results There was a total of 191,054 incidences and 81,229 death were recorded in Asian countries in 2012. Among the Asian countries, the five countries with the highest standardized incidence rates of prostate cancer were Israel, Turkey, Lebanon, Singapore, and Japan, and the five countries with the highest standardized mortality rates were Turkey, Lebanon, Timor-Leste, Armenia, and the Philippines. The correlation between standardized incidence rate of prostate cancer and the HDI was 0.604 (P ≤ 0.001), with life expectancy at birth 0.529 (P = 0.002), with mean years of schooling 0.427 (P = 0.001), and with level of income per each person of the population 0.349 (P = 0.013). Also, between the standardized mortality rate and the HDI, it was 0.228 (P = 0.127). Conclusions A significant and positive correlation was observed between the standardized incidence rate of prostate cancer, and the HDI and its dimensions, such as life expectancy at birth, mean years of schooling, and income level of the population per each person of population. However, there was no significant correlation between the standardized mortality rate, and the HDI and its dimensions. PMID:26779461

The incidence and mortality of prostate cancer and its relationship with development in Asia.

PubMed

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Pakzad, Iraj; Salehiniya, Hamid

2015-12-01

Prostate cancer is a common cancer in men in the world. It is rapidly increasing. This study investigated the incidence and mortality of prostate cancer and the relationship with the Human Development Index (HDI) and its dimensions in Asia in 2012. The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). The standardized incidence and mortality rates of prostate cancer were calculated for Asian countries. The correlation between incidence, mortality rates, and the HDI and its components were assessed with the use of the correlation test, using SPSS software. There was a total of 191,054 incidences and 81,229 death were recorded in Asian countries in 2012. Among the Asian countries, the five countries with the highest standardized incidence rates of prostate cancer were Israel, Turkey, Lebanon, Singapore, and Japan, and the five countries with the highest standardized mortality rates were Turkey, Lebanon, Timor-Leste, Armenia, and the Philippines. The correlation between standardized incidence rate of prostate cancer and the HDI was 0.604 (P ≤ 0.001), with life expectancy at birth 0.529 (P = 0.002), with mean years of schooling 0.427 (P = 0.001), and with level of income per each person of the population 0.349 (P = 0.013). Also, between the standardized mortality rate and the HDI, it was 0.228 (P = 0.127). A significant and positive correlation was observed between the standardized incidence rate of prostate cancer, and the HDI and its dimensions, such as life expectancy at birth, mean years of schooling, and income level of the population per each person of population. However, there was no significant correlation between the standardized mortality rate, and the HDI and its dimensions.

Making and Using Aesthetically Pleasing Images With HDI

NASA Astrophysics Data System (ADS)

Buckner, Spencer L.

2017-01-01

The Half-Degree Imager (HDI) was installed as the primary imager on the 0.9-m WIYN telescope in October 2013. In the three plus years since then it has proven to be highly effective as a scientific instrument for the 0.9-m WIYN consortium. One thing that has been missing from the mix are aesthetically pleasing images for use in publicity and public outreach. The lack of “pretty pictures” is understandable since the HDI is designed for scientific use and observers are given limited telescope time. However, images which appeal to the general public can be an effective tool for public outreach, publicity and recruitment of students into astronomy programs. As a counter to the loss of limited telescope time an observer has, “pretty picture” images can be taken under less than desirable conditions when photometric studies would have limited usefulness. Astroimaging has become a popular pastime among both amateur and professional astronomers. At Austin Peay State University astrophotography is a popular course with non-science majors that wish to complete an astronomy minor as well as physics majors pursuing the astrophysics track. Images of a number of Messier objects have been taken with the HDI camera and are used to teach the basics of image calibration and processing for aesthetic value to students in the astrophotography class. Using HDI images with most image processing software commercially available to the public does present some problems, though. The extended FITS format of the images is not readable by most amateur image processing software and such software can also have problems recognizing the filter configurations of the HDI. Overcoming these issues and how the images are used in APSU courses, publicity and public outreach as well as finished pictures will be discussed in this presentation. A poster describing the processing techniques used will be displayed during the concurrent HDI poster session along with several poster-sized prints of images.

Fate and potential environmental effects of methylenediphenyl diisocyanate and toluene diisocyanate released into the atmosphere.

PubMed

Tury, Bernard; Pemberton, Denis; Bailey, Robert E

2003-01-01

Information from a variety of sources has been collected and summarized to facilitate an overview of the atmospheric fate and potential environmental effects of emissions of methylenediphenyl diisocyanate (MDI) or toluene diisocyanate (TDI) to the atmosphere. Atmospheric emissions of both MDI and TDI are low, both in terms of concentration and mass, because of their low volatility and the need for careful control over all aspects of their lifecycle from manufacture through disposal. Typical emission losses for TDI are 25 g/t of TDI used in slabstock foam production. MDI emission losses are lower, often less than 1 g/t of MDI used. Dispersion modeling predicts that concentrations at the fenceline or beyond are very low for typical releases. Laboratory studies show that TDI (and by analogy MDI) does not react with water in the gas phase at a significant rate. The primary degradation reaction of these aromatic diisocyanates in the atmosphere is expected to be oxidation by OH radicals with an estimated half-life of one day. Laboratory studies also show that this reaction is not expected to result in increased ground-level ozone accumulation.

Methylene Diphenyl Diisocyanate (MDI) And Related Compounds

EPA Pesticide Factsheets

This document addresses the use of methylene diphenyl diisocyanate (MDI) and related compounds (See Appendix 1) in products that may result in consumer and general population exposures, particularly in or around buildings, including homes and schools.

The use of high-dose insulin therapy and intravenous lipid emulsion to treat severe, refractory diltiazem toxicosis in a dog.

PubMed

Maton, Barbara L; Simmonds, Erin E; Lee, Justine A; Alwood, Amy J

2013-01-01

To describe the novel use of high-dose insulin (HDI) therapy and intravenous lipid emulsion (ILE) to treat refractory, severe diltiazem toxicosis in a dog. A 4-year-old Pomeranian was presented for treatment 2.5 hours following ingestion of a diltiazem extended-release capsule. Toxic ingestion was calculated at a maximum exposure of 79 mg/kg, with a reported canine LD50 of 50 mg/kg. Clinical signs of progressive hypotension and severe bradycardia with atrial standstill were observed, which persisted despite treatment with atropine, calcium, glucagon, and dopamine. The novel use of HDI and ILE as part of therapy for diltiazem toxicosis resulted in clinical resolution of life-threatening signs. Within 1 hour of initiating HDI therapy, the clinical signs improved, and with continued treatment, the patient remained normotensive and survived to discharge. To the authors' knowledge, this is the first reported clinical case describing the use of both HDI and ILE therapy in the treatment of severe refractory diltiazem toxicosis in veterinary medicine. No significant adverse effects were observed from the treatment. In veterinary patients with severe refractory calcium channel blocker toxicosis, the use of HDI and ILE should be considered for life-threatening clinical signs. © Veterinary Emergency and Critical Care Society 2013.

ERalpha and ERbeta expression and transcriptional activity are differentially regulated by HDAC inhibitors

PubMed Central

Duong, Vanessa; Licznar, Anne; Margueron, Raphaël; Boulle, Nathalie; Busson, Muriel; Lacroix, Matthieu; Katzenellenbogen, Benita S.; Cavaillès, Vincent; Lazennec, Gwendal

2006-01-01

The proliferative action of ERα largely accounts for the carcinogenic activity of estrogens. By contrast, recent data show that ERβ displays tumor-suppressor properties, thus supporting the interest to identify compounds which could increase its activity. Here, we show that histone deacetylase inhibitors (HDI) up-regulated ERβ protein levels, whereas it decreased ERα expression. Part of this regulation took place at the mRNA level through a mechanism independent of de novo protein synthesis. In addition, we found that, in various cancer cells, the treatment with different HDI enhanced the ligand-dependent activity of ERβ more strongly than that of ERα. On the other hand, in MDA-MB231 and HeLa cells, the expression of ERs modified the transcriptional response to HDI. The use of deletion mutants of both receptors demonstrated that AF1 domain of the receptors was required. Finally, we show that ERβ expression led to a dramatic increased in the antiproliferative activity of HDI, which correlated with a modification of the transcription of genes involved in cell cycle control by HDI. Altogether, these data demonstrate that the interference of ERβ and HDAC on the control of transcription and cell proliferation constitute a promising approach for cancer therapy. PMID:16158045

The role of isocyanates in determining the viscoelastic properties of polyurethane

NASA Astrophysics Data System (ADS)

AqilahHamuzan, Hawa; Badri, Khairiah Haji

2016-11-01

Polyurethane (PU) has a unique structure that is dependent on the structure of the starting material used. This research focused on investigating the role of isocyanate groups (NCO) in the determination of the viscoelastic properties of the polymer. Monoester polyol was reacted with three different diisocyanates separately by prepolymerization method. The diisocyanates used were 2,4-diphenyl methane diisocyanate (MDI), toluene 2,4-diisocyanate (TDI) and isophoronediisocyanate (IPDI). Acetone was used as a solvent. IPDI, MDI and TDI were reacted with monoester polyol at ratios of 10:9, 10:10, 10:12 and 10:14 (polyol:diisocyanate). Then, the PU foams produced by the curing process were analyzed by Fourier Transform infrared spectroscopy (FTIR). The FTIR spectra showed the presence of the amide peak (-NH) and the absence of hydroxyl peak (-OH) indicated that the reaction between polyol and diisocyanate has occurred. However, the soxhlet extraction showed that only MDI-based PUs contain crosslinking bond. These cross-linking bond at the ratio of 10:10, 10:12 and 10:14 were 41.3 %,61.1 % and 74.1 % respectively. Thermal properties of the PU foams were determined by differential scanning calorimetry (DSC) and thermogravimetry (TGA) techniques. MDI-based PUs and TDI-based PUs show two values of Tg while IPDI-based PUs only show one Tg value. The tensile strains of PU foams decreased with increasing ratio of isocyanate. Meanwhile, PU foams with ratio of polyol to isocyanate at 10:12 showed the highest tensile stress and modulus compared to at 10:10 and 10:14.

Sensitization and cross-reactivity patterns of contact allergy to diisocyanates and corresponding amines: investigation of diphenylmethane-4,4'-diisocyanate, diphenylmethane-4,4'-diamine, dicyclohexylmethane-4,4'-diisocyanate, and dicylohexylmethane-4,4'-diamine.

PubMed

Hamada, Haneen; Bruze, Magnus; Zimerson, Erik; Isaksson, Marléne; Engfeldt, Malin

2017-10-01

Isocyanates are used in polyurethane production. Dermal exposure to isocyanates can induce contact allergy. The most common isocyanate is diphenylmethane diisocyanate used for industrial purposes. The isomer diphenylmethane-4,4'-diisocyanate (4,4'-MDI) is used in patch testing. Diphenylmethane-4,4'-diamine (4,4'-MDA) is its corresponding amine. Concurrent reactions to 4,4'-MDI and 4,4'-MDA have been reported, as have concurrent reactions to 4,4'-MDI and dicyclohexylmethane-4,4'-diisocyanate (4,4'-DMDI). To investigate the sensitization capacities and the cross-reactivity of 4,4'-MDI, 4,4'-MDA, 4,4'-DMDI, and dicyclohexylmethane-4,4'-diamine (4,4'-DMDA). The guinea-pig maximization test (GPMT) was used. The GPMT showed sensitizing capacities for all investigated substances: 4,4'-MDI, 4,4'-MDA, 4,4'-DMDI, and 4,4'-DMDA (all p < 0.001). 4,4'-MDI-sensitized animals showed cross-reactivity to 4,4'-MDA (p < 0.001) and 4,4'-DMDI (all p < 0.05). 4,4'-MDA-sensitized animals showed cross-reactivity to 4,4'-DMDA (p = 0.008). All of the investigated substances were shown to be strong sensitizers. Animals sensitized to 4,4'-MDI showed cross-reactivity to 4,4'-MDA and 4,4'-DMDI, supporting previous findings in the literature. The aromatic amine 4,4'-MDA showed cross-reactivity to the aliphatic amine 4,4'-DMDA. © 2017 The Authors. Contact Dermatitis published by John Wiley & Sons Ltd.

Effort-reward imbalance at work, over-commitment personality and diet quality in Central and Eastern European populations.

PubMed

Chen, Sung-Wei; Peasey, Anne; Stefler, Denes; Malyutina, Sofia; Pajak, Andrzej; Kubinova, Ruzena; Chan, Jen-Hui; Bobak, Martin; Pikhart, Hynek

2016-04-14

The aims of this study were to investigate the associations between work stress defined by the effort-reward imbalance (ERI) model and diet quality and to examine the potential role of over-commitment (OC) personality in ERI-diet relationships. A cross-sectional study was conducted in random population samples of 6340 men and 5792 women (age 45-69 years) from the Czech Republic, Russia and Poland. Dietary data were collected using FFQ. The healthy diet indicator (HDI) was constructed using eight nutrient/food intakes (HDI components) to reflect the adherence to WHO dietary guideline. The extent of imbalance between effort and reward was measured by the effort:reward (ER) ratio; the effort score was the numerator and the reward score was multiplied by a factor adjusting for unequal number of items in the denominator. Logistic regression and linear regression were used to assess the associations between exposures (ER ratio and OC) and outcomes (HDI components and HDI) after adjustment for confounders and mediators. The results showed that high ER ratio and high OC were significantly associated with unhealthy diet quality. For a 1-SD increase in the ER ratio, HDI was reduced by 0·030 and 0·033 sd in men and women, and for a 1-SD increase in OC, HDI was decreased by 0·036 and 0·032 sd in men and women, respectively. The modifying role of OC in ERI-diet relationships was non-significant. To improve diet quality at workplace, a multiple-level approach combining organisational intervention for work stress and individual intervention for vulnerable personality is recommended.

Global incidence and mortality rates in pancreatic cancer and the association with the Human Development Index: decomposition approach.

PubMed

Veisani, Y; Jenabi, E; Khazaei, S; Nematollahi, Sh

2018-03-01

Pancreatic cancer has a lower morbidity yet higher case fatality rates (CFRs) compared with other gastrointestinal cancers. The effects of socio-economic components on pancreatic cancer rates have been acknowledged; however, the effects of the Human Development Index (HDI) inequality are not. In this study, we aimed to determine the contribution of important socio-economic components on pancreatic cancer rates using a decomposition approach. Global ecological study. Incidence and mortality rates of pancreatic cancer were obtained for 172 countries from GLOBOCAN and the United Nations Development Program. The World Bank database was also used to obtain the HDI and its gradient for 169 countries. Inequality in pancreatic cancer age-specific incidence and mortality rates was calculated according to the HDI using the concentration index (CI). We decomposed the CI to determine main contributors of the inequality. The CI for incidence and mortality of pancreatic cancer in both genders according to the HDI was 0.26 (95% confidence interval: 0.21-0.30) and 0.25 (95% confidence interval: 0.21-0.30), respectively, which indicated more concentrated inequality in advantaged countries. About 80% of the inequality sources were predicted by socio-economic component in both rates of pancreatic cancer. The main contributors to inequality were the mean years of schooling, life expectancy at birth, expected years of schooling, and urbanization. Global inequalities exist in pancreatic cancer incidence and mortality rates according to the HDI; in addition, inequality was more concentrated in countries with higher score of HDI. Copyright © 2017 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

Incidence and Mortality of Colorectal Cancer and Relationships with the Human Development Index across the World.

PubMed

Rafiemanesh, Hosein; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Sepehri, Zahra; Shamlou, Reza; Salehiniya, Hamid; Towhidi, Farhad; Makhsosi, Behnam Reza

2016-01-01

This study aimed to investigate the standardized incidence and mortality rate of colorectal cancer and its relationship with the human development index (HDI) across the world in 2012. This ecologic study was conducted for assessment of the correlation between age-specific incidence rate (ASIR) and age-specific mortality rate (ASMR) with HDI and its components. Data for SIR and SMR for every country for the year 2012 were obtained from the global cancer project. We used a bivariate method for assessment of the correlation between SIR and SMR and HDI. Statistical significance was assumed at <0.05. Statistical analyses were performed using SPSS (Version 22.0, SPSS Inc.). Countries with the highest SIR of colorectal cancer in the world in 2012, were Republic of Korea, Slovakia, Hungary and countries with the highest SMR were Hungary, Croatia and Slovakia. The correlation between SIR of colorectal cancer and the HDI was 0.712 (P≤0.001), with life expectancy at birth 0.513 (P≤0.001), with mean years of schooling 0.641 (P≤0.001) and with level of income per each person of the population 0.514 (P=0.013). In addition, the correlation between SMR of colorectal cancer and the HDI was 0.628 (P≤0.001), with life expectancy at birth 0.469 (P≤0.001), with mean years of schooling 0.592 (P≤0.001) and with level of income per each person of the population 0.378 (P=0.013). The highest SIR and SMR of colorectal cancer was in the WHO Europe region. There was a positive correlation between HDI and SIR and SMR of colorectal cancer.

Incidence and Mortality of Bladder Cancer and their Relationship with Development in Asia.

PubMed

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Mohammadian, Mahdi; Pakzad, Iraj; Safiri, Saeid; Khazaei, Salman; Salehiniya, Hamid

2015-01-01

Over the past decade, bladder cancer was associated with a significant increase. Given the importance of the impact of socioeconomic status on the distribution of cancer incidence and mortality, and the need to information on these parameters for prevention planning, the aim of this study was to evaluate data for bladder cancer and their relationship with human development index (HDI) and its components in Asia in 2012. The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). The incidence and mortality rates were drawn for Asian countries. To analyze data, correlation tests between incidence and death rates, and HDI and its components were employed with a significance level of 0.05 using SPSS software. A total incidence of 696,231 cases (68.7% in males and 31.3% in females, sex ratio of 2.19:1) and 524,465 deaths (67.0% in men and 32.9% in women, sex ratio was 2.03:1) were recorded in Asian countries in 2012. Correlation between HDI and standardized incidence rate was 0.241 overall (p=0.106), 0.236 in men (p=0.114) and -0.250 in women (p=0.094). Also between HDI and standardized mortality rate 0.025 (p=0.871) in men 0.118 (p=0.903) and in women 0.014 (p=0.927). Bladder cancer incidence is higher in developed countries, but the rate is declining, and in less developed and developing countries it is growing. There was no statistically significant correlation between the standardized incidence rate of bladder cancer and the HDI and its dimensions in Asia, except for the level of education.

PULMONARY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO SELECTED DIISOCYANATES

EPA Science Inventory

PULMONARY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO SELECTED DIISOCYANATES

M.J.K. Selgrade, E.H. Boykin, N.H. Coates, D.L. Doerfler, S.H. Gavett
Experimental Toxicology Div., National Health and Environmental Research Laboratory, Office of Research and Developmen...

Water-free synthesis of polyurethane foams using highly reactive diisocyanates derived from 5-hydroxymethylfurfural.

PubMed

Neumann, Christopher N D; Bulach, Winfried D; Rehahn, Matthias; Klein, Roland

2011-09-01

This paper reports on the synthesis of a new highly reactive diisocyanate monomer based on hydroxymethylfurfural. It further describes its catalyst-free conversion to linear-chain thermoplastic polyurethanes as well as to cross-linked polyurethane foams. In addition, a novel strategy for the synthesis of polyurethane foams without the necessity of using water is developed. Nitrogen is utilized herein as blowing agent which is formed during Curtius rearrangement of a new furan based carboxylic azide into its corresponding diisocyanate. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Methylene Diphenyl Diisocyanate (monomeric MDI) and polymeric MDI (PMDI)

Integrated Risk Information System (IRIS)

TOXICOLOGICAL REVIEW of METHYLENE DIPHENYL DIISOCYANATE ( MDI ) ( CAS No . 101 - 68 - 8 and 9016 - 87 - 9 ) In Support of Summary Information on the Integrated Risk Information System ( IRIS ) February 1998 U.S . ENVIRONMENTAL PROTECTION AGENCY WASHINGTON , DC TABLE OF CONTENTS TOXICOLOGICAL REV

40 CFR 721.2540 - Diphenylmethane diisocyanate (MDI) modified.

Code of Federal Regulations, 2010 CFR

2010-07-01

...) TOXIC SUBSTANCES CONTROL ACT SIGNIFICANT NEW USES OF CHEMICAL SUBSTANCES Significant New Uses for Specific Chemical Substances § 721.2540 Diphenylmethane diisocyanate (MDI) modified. (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified generically as a...

Global Incidence and Mortality Rates of Stomach Cancer and the Human Development Index: an Ecological Study.

PubMed

Khazaei, Salman; Rezaeian, Shahab; Soheylizad, Mokhtar; Khazaei, Somayeh; Biderafsh, Azam

2016-01-01

Stomach cancer (SC) is the second leading cause of cancer death with the rate of 10.4% in the world. The correlation between the incidence and mortality rates of SC and human development index (HDI) has not been globally determined. Therefore, this study aimed to determine the association between the incidence and mortality rates of SC and HDI in various regions. In this global ecological study, we used the data about the incidence and mortality rate of SC and HDI from the global cancer project and the United Nations Development Programme database, respectively. In 2012, SCs were estimated to have affected a total of 951,594 individuals (crude rate: 13.5 per 100,000 individuals) with a male/female ratio of 1.97, and caused 723,073 deaths worldwide (crude rate: 10.2 per 100,000 individuals). There was a positive correlation between the HDI and both incidence (r=0.28, <0.05) and mortality rates of SC (r=0.13, P = 0.1) in the world in 2012. The high incidence and mortality rates of SC in countries with high and very high HDI is remarkable which should be the top priority of interventions for global health policymakers. In addition, health programs should be provided to reduce the burden of this disease in the regions with high incidence and mortality rates of SC.

Lack of Any Relationship of Stomach Cancer Incidence and Mortality with Development in Asia.

PubMed

RaFiei, Elahe; Mohammadian-Hafshejani, Abdollah; Towhidi, Farhad; Makhsosi, Behnam Reza; Salehiniya, Hamid

2016-01-01

The aim of this study was to evaluate the incidence and mortality of stomach cancer, and its relationship with the Human Development Index (HDI) and its components in Asia in 2012. This ecological study was conducted based on GLOBOCAN project of WHO for Asian countries. We assessed the correlations between standardized incidence rates (SIR) and standardized mortality rates (SMR) of stomach cancer with HDI and its components using SPSS18. A total of 696,231 cases (68.7% in males and 31.3% in females, ratio of 2.19:1) and 524,465 deaths (67.1% in men and 33.0% in women, ratio 2.03:1) were included in 2012. Five countries with the highest SIR of stomach cancer were Republic Korea, Mongolia, Japan, China and Tajikistan. Five countries with the highest SMR of stomach cancer were Mongolia, Tajikistan, Kyrgyzstan, Kazakhstan and China. Correlation between HDI and SIR was 0.241 (p = 0.106), in men 0.236 (p = 0.114) and in women -0.250 (p = 0.094). Also between HDI and SMR -0.250 (p = 0.871) in men -0.018 (p = 0.903) and in women -0.014 (p = 0.927). No significant correlation was observed between the SIR of stomach cancer, and the HDI and its dimensions, such as life expectancy at birth, mean years of schooling, and income level of the population.

Synthesis and characterization of polyurethane/bentonite nanoclay based nanocomposites using different diisocyanates: relation between mechanical and thermal properties

NASA Astrophysics Data System (ADS)

Bocchio, Javier; Wittemberg, Víctor; Quagliano, Javier

2017-05-01

Polyurethanes (PUs) and polyurethane nanocomposites (PUNC) with bentonite nanoclay were prepared by the reaction of toluene-2,4-diisocyanate (TDI), dimeryl diisocyanate (DDI) and isophorone diisocyanate (IPDI) with two different polymers: hydroxyl terminated polybutadiene (HTPB) and polytetramethylene ether glycol (PTMEG), and the chains were further extended with 1,4-butanediol (1,4-BDO) to get final PUs and PUNCs. PUNCs were prepared by dispersing within the polymers a commercial and a synthesized bentonite nanoclay by mechanical dispersion. Mechanical properties showed that the addition of a small amount of nanoclay resulted in a significant increase in tensile strength and reduction in elongation at break (maximum increase of 2.3 and 5-times reduction, respectively, for a HTPB-TDI-BDO PUNCs). Thermal analysis revealed that the addition of nanoclays improved the thermal stability and increased decomposition temperature of PUNCs. We concluded that there is a positive correlation between mechanical and thermal properties as a result of nanoclay addition.

2,4-/2,6-Toluene diisocyanate mixture (TDI)

Integrated Risk Information System (IRIS)

2,4 - / 2,6 - Toluene diisocyanate mixture ( TDI ) ; CASRN 26471 - 62 - 5 Human health assessment information on a chemical substance is included in the IRIS database only after a comprehensive review of toxicity data , as outlined in the IRIS assessment development process . Sections I ( Health Haz

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 12 2012-07-01 2011-07-01 true Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

40 CFR 63.1294 - Standards for slabstock flexible polyurethane foam production-diisocyanate emissions.

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 11 2011-07-01 2011-07-01 false Standards for slabstock flexible polyurethane foam production-diisocyanate emissions. 63.1294 Section 63.1294 Protection of Environment... Flexible Polyurethane Foam Production § 63.1294 Standards for slabstock flexible polyurethane foam...

A Calibrated Index of Human Development

ERIC Educational Resources Information Center

Lind, Niels

2010-01-01

The weightings of the four component indicators of the UNDP's Human Development Index HDI appear to be arbitrary and have not been given justification. This paper develops a variant of the HDI, calculated to reflect peoples' revealed evaluations of education and the productivity of work. The resulting Calibrated human Development Index CDI has a…

"Healthy" Human Development Indices

ERIC Educational Resources Information Center

Engineer, Merwan; Roy, Nilanjana; Fink, Sari

2010-01-01

In the Human Development Index (HDI), life expectancy is the only indicator used in modeling the dimension "a long and healthy life". Whereas life expectancy is a direct measure of quantity of life, it is only an indirect measure of healthy years lived. In this paper we attempt to remedy this omission by introducing into the HDI the morbidity…

Dataset on the prevalence of tobacco smoking in men and women of selected countries whit difference human development.

PubMed

Riahi, Mina; Mohammadi, Ali Akbar; Rohani, Hosein; Bidkhori, Mohammad

2018-06-01

This study was conducted to investigate the effect of human development index (HDI) on tobacco smoking prevalence in men and women of countries which their data about tobacco smoking were available for 2015. Pearson's correlation coefficient and linear regression were used to investigate the association between HDI and all types of smoking, particularly cigarette. Daily smoking and current smoking were used as tobacco smoking indices. The information about prevalence of tobacco smoking and HDI was obtained from the World Health Organization (WHO) website and United Nations Development Programme (UNDP), respectively. The results showed that there is no statistically significant relationship between HDI and current tobacco smoking in men (B = -0.45_CI 95%: -29.97, 29.06). However, the same association was significant for women (B = 43.87, CI 95%: 24.97-62.78). The results indicated that women in developed countries are more at risk of health effects attributed to tobacco smoking. Countries should focus on socioeconomic factors to prevent the spread of risk factors for non-communicable diseases.

Using the ATL HDI 1000 to collect demodulated RF data for monitoring HIFU lesion formation

NASA Astrophysics Data System (ADS)

Anand, Ajay; Kaczkowski, Peter J.; Daigle, Ron E.; Huang, Lingyun; Paun, Marla; Beach, Kirk W.; Crum, Lawrence A.

2003-05-01

The ability to accurately track and monitor the progress of lesion formation during HIFU (High Intensity Focused Ultrasound) therapy is important for the success of HIFU-based treatment protocols. To aid in the development of algorithms for accurately targeting and monitoring formation of HIFU induced lesions, we have developed a software system to perform RF data acquisition during HIFU therapy using a commercially available clinical ultrasound scanner (ATL HDI 1000, Philips Medical Systems, Bothell, WA). The HDI 1000 scanner functions on a software dominant architecture, permitting straightforward external control of its operation and relatively easy access to quadrature demodulated RF data. A PC running a custom developed program sends control signals to the HIFU module via GPIB and to the HDI 1000 via Telnet, alternately interleaving HIFU exposures and RF frame acquisitions. The system was tested during experiments in which HIFU lesions were created in excised animal tissue. No crosstalk between the HIFU beam and the ultrasound imager was detected, thus demonstrating synchronization. Newly developed acquisition modes allow greater user control in setting the image geometry and scanline density, and enables high frame rate acquisition. This system facilitates rapid development of signal-processing based HIFU therapy monitoring algorithms and their implementation in image-guided thermal therapy systems. In addition, the HDI 1000 system can be easily customized for use with other emerging imaging modalities that require access to the RF data such as elastographic methods and new Doppler-based imaging and tissue characterization techniques.

Human development, poverty, health & nutrition situation in India.

PubMed

Antony, G M; Laxmaiah, A

2008-08-01

Human development index (HDI) is extensively used to measure the standard of living of a country. India made a study progress in the HDI value. Extreme poverty is concentrated in rural areas of northern States while income growth has been dynamic in southern States and urban areas. This study was undertaken to assess the trends in HDI, human poverty index (HPI) and incidence of poverty among Indian states, the socio-economic, health, and diet and nutritional indicators which determine the HDI, changes in protein and calorie adequacy status of rural population, and also trends in malnutrition among children in India. The variations in socio-economic, demographic and dietary indicators by grades of HDI were studied. The trends in poverty and nutrition were also studied. Univariate, bivariate and multivariate analysis were done to analyse data. While India's HDI value has improved over a time; our rank did not improve much compared to other developing countries. Human poverty has not reduced considerably as per the HPI values. The undernutrition among preschool children is still a major public health problem in India. The incidence of poverty at different levels of calorie requirement has not reduced in both rural and urban areas. The time trends in nutritional status of pre-school children showed that, even though, there is an improvement in stunting over the years, the trend in wasting and underweight has not improved much. Proper nutrition and health awareness are important to tackle the health hazards of developmental transition. Despite several national nutrition programmes in operation, we could not make a significant dent in the area of health and nutrition. The changing dietary practices of the urban population, especially the middle class, are of concern. Further studies are needed to measure the human development and poverty situation of different sections of the population in India using an index, which includes both income indicators and non income indicators.

Optimized spatial priorities for biodiversity conservation in China: a systematic conservation planning perspective.

PubMed

Wu, Ruidong; Long, Yongcheng; Malanson, George P; Garber, Paul A; Zhang, Shuang; Li, Diqiang; Zhao, Peng; Wang, Longzhu; Duo, Hairui

2014-01-01

By addressing several key features overlooked in previous studies, i.e. human disturbance, integration of ecosystem- and species-level conservation features, and principles of complementarity and representativeness, we present the first national-scale systematic conservation planning for China to determine the optimized spatial priorities for biodiversity conservation. We compiled a spatial database on the distributions of ecosystem- and species-level conservation features, and modeled a human disturbance index (HDI) by aggregating information using several socioeconomic proxies. We ran Marxan with two scenarios (HDI-ignored and HDI-considered) to investigate the effects of human disturbance, and explored the geographic patterns of the optimized spatial conservation priorities. Compared to when HDI was ignored, the HDI-considered scenario resulted in (1) a marked reduction (∼9%) in the total HDI score and a slight increase (∼7%) in the total area of the portfolio of priority units, (2) a significant increase (∼43%) in the total irreplaceable area and (3) more irreplaceable units being identified in almost all environmental zones and highly-disturbed provinces. Thus the inclusion of human disturbance is essential for cost-effective priority-setting. Attention should be targeted to the areas that are characterized as moderately-disturbed, <2,000 m in altitude, and/or intermediately- to extremely-rugged in terrain to identify potentially important regions for implementing cost-effective conservation. We delineated 23 primary large-scale priority areas that are significant for conserving China's biodiversity, but those isolated priority units in disturbed regions are in more urgent need of conservation actions so as to prevent immediate and severe biodiversity loss. This study presents a spatially optimized national-scale portfolio of conservation priorities--effectively representing the overall biodiversity of China while minimizing conflicts with economic development. Our results offer critical insights for current conservation and strategic land-use planning in China. The approach is transferable and easy to implement by end-users, and applicable for national- and local-scale systematic conservation prioritization practices.

Optimized Spatial Priorities for Biodiversity Conservation in China: A Systematic Conservation Planning Perspective

PubMed Central

Wu, Ruidong; Long, Yongcheng; Malanson, George P.; Garber, Paul A.; Zhang, Shuang; Li, Diqiang; Zhao, Peng; Wang, Longzhu; Duo, Hairui

2014-01-01

By addressing several key features overlooked in previous studies, i.e. human disturbance, integration of ecosystem- and species-level conservation features, and principles of complementarity and representativeness, we present the first national-scale systematic conservation planning for China to determine the optimized spatial priorities for biodiversity conservation. We compiled a spatial database on the distributions of ecosystem- and species-level conservation features, and modeled a human disturbance index (HDI) by aggregating information using several socioeconomic proxies. We ran Marxan with two scenarios (HDI-ignored and HDI-considered) to investigate the effects of human disturbance, and explored the geographic patterns of the optimized spatial conservation priorities. Compared to when HDI was ignored, the HDI-considered scenario resulted in (1) a marked reduction (∼9%) in the total HDI score and a slight increase (∼7%) in the total area of the portfolio of priority units, (2) a significant increase (∼43%) in the total irreplaceable area and (3) more irreplaceable units being identified in almost all environmental zones and highly-disturbed provinces. Thus the inclusion of human disturbance is essential for cost-effective priority-setting. Attention should be targeted to the areas that are characterized as moderately-disturbed, <2,000 m in altitude, and/or intermediately- to extremely-rugged in terrain to identify potentially important regions for implementing cost-effective conservation. We delineated 23 primary large-scale priority areas that are significant for conserving China's biodiversity, but those isolated priority units in disturbed regions are in more urgent need of conservation actions so as to prevent immediate and severe biodiversity loss. This study presents a spatially optimized national-scale portfolio of conservation priorities – effectively representing the overall biodiversity of China while minimizing conflicts with economic development. Our results offer critical insights for current conservation and strategic land-use planning in China. The approach is transferable and easy to implement by end-users, and applicable for national- and local-scale systematic conservation prioritization practices. PMID:25072933

40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

Code of Federal Regulations, 2010 CFR

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is...

40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

Code of Federal Regulations, 2011 CFR

2011-07-01

... 40 Protection of Environment 31 2011-07-01 2011-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is...

40 CFR 721.10693 - Diphenylmethane diisocyanate polymer with alkanoic diacid and alkanediol (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Diphenylmethane diisocyanate polymer... polymer with alkanoic diacid and alkanediol (generic). (a) Chemical substance and significant new uses... polymer with alkanoic diacid and alkanediol (PMN P-13-338) is subject to reporting under this section for...

40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

Code of Federal Regulations, 2013 CFR

2013-07-01

... 40 Protection of Environment 32 2013-07-01 2013-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is...

40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

... 40 Protection of Environment 31 2014-07-01 2014-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is...

40 CFR 721.463 - Acrylate of polymer based on isophorone diisocyanate (generic).

Code of Federal Regulations, 2012 CFR

2012-07-01

... 40 Protection of Environment 32 2012-07-01 2012-07-01 false Acrylate of polymer based on... New Uses for Specific Chemical Substances § 721.463 Acrylate of polymer based on isophorone... substance identified generically as acrylate of polymer based on isophorone diisocyanate (PMN P-00-0626) is...

Negative and Positive Partial Mobility: A Study of the Relative Changes in Human Development

ERIC Educational Resources Information Center

Sengupta, Atanu; Ghosh, Abhijit

2010-01-01

In this paper, we have considered the issues concerning dynamic changes in HDI and its various components from a relative standpoint. The analysis of HDI mobility should entail directional movement introduced by Fields (in Distribution and development: a new look at the developing world. MIT Press, Cambridge, 2001). However, Fields' analysis was…

Keeping Things Simple: Why the Human Development Index Should Not Diverge from Its Equal Weights Assumption

ERIC Educational Resources Information Center

Stapleton, Lee M.; Garrod, Guy D.

2007-01-01

Using a range of statistical criteria rooted in Information Theory we show that there is little justification for relaxing the equal weights assumption underlying the United Nation's Human Development Index (HDI) even if the true HDI diverges significantly from this assumption. Put differently, the additional model complexity that unequal weights…

Housing Quality and Access to Material and Learning Resources within the Home Environment in Developing Countries

PubMed Central

Bradley, Robert H.; Putnick, Diane L.

2011-01-01

This study examined home environment conditions (housing quality, material resources, formal and informal learning materials) and their relations with the Human Development Index (HDI) in 28 developing countries. Home environment conditions in these countries varied widely. The quality of housing and availability of material resources at home were consistently tied to HDI; the availability of formal and informal learning materials little less so. Gross domestic product (GDP) tended to show a stronger independent relation with housing quality and material resources than life expectancy and education. Formal learning resources were independently related to the GDP and education indices, and informal learning resources were not independently related to any constituent indices of the overall HDI. PMID:22277008

Compatibility of melt-processed zein blends with methylenediphenyl 4,4'-diisocyanate-thermal, mechanical and physical properties

USDA-ARS?s Scientific Manuscript database

Corn zein was melt-processed with methylenediphenyl 4,4'-diisocyanate (MDI) using triethylamine (TEA) as catalyst. The objective is to construct a melt-processed, compatible blend of zein with MDI that can be used as a building block for generating bio-based thermoplastics. The impact of cross-linki...

[Migrations in Latin American countries. Characteristics of the pediatric population].

PubMed

Vásquez-De Kartzow, Rodrigo; Castillo-Durán, Carlos; Lera M, Lydia

2015-01-01

Migration is a growing phenomenon among Latin American countries (LAC) as well as others; however, scarce information is available studying its impact on paediatric groups and its association with socioeconomic variables. To study the association among socioeconomic variables and the immigration rate of paediatric population in LAC. Official rates of migration of LAC were obtained from: International Organization for Migration, Pan American Health Organization, and United Nations Development Programme. Demographic and socioeconomic information was also obtained for: gross domestic product (GDP), human development index (HDI), Gini coefficient of inequality (GC), alphabetization rate for adults (AA), net migration rate (NMR), and immigration of children<15 years (IM15). Description, linear correlations and analysis of differences between groups of countries were assessed. The NMR was positive for Costa Rica, Panama, Venezuela, Chile and Argentina. No association among NMR and GDP, HDI, GC, AA was found. A correlation of IM15 was found with: GC (r=0.668, P=.01), with GDP (r=-0.720; P=.01), AA (r=-0.755; P=.01) and with HDI (r=-0.799; P=.01). Rate of IM15 was lower in LA countries with advanced/medium development (GDP>median) vs those with low development (Fisher, P<.0001). There is a direct inverse association between GDP per capita, HDI, AA and GC and the proportion of each country IN15. We did not observe an association between NMR and HDI, AA, and GC. The health impact of these migrations should be analysed. Copyright © 2015. Publicado por Elsevier España, S.L.U.

Epidemiology, incidence and mortality of lung cancer and their relationship with the development index in the world

PubMed Central

Rafiemanesh, Hosein; Mehtarpour, Mojtaba; Khani, Farah; Hesami, Sayed Mohammadali; Shamlou, Reza; Towhidi, Farhad; Makhsosi, Behnam Reza; Moini, Ali

2016-01-01

Background The highest incidence of lung cancer is seen in North America and the lowest incidence in central Africa. Socioeconomic factors of inequality reflect regional disparities in human development. Due to the importance of awareness about incidence and mortality of lung cancer in health programming and the possible role of the human development index (HDI), this study was done with the aim to investigate the epidemiology of lung cancer in the world and its relationship with HDI. Methods The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). Data about the age-specific incidence and mortality rate (ASR) for every country in 2012 were getting from the global cancer project. To analyze data, correlation tests between incidence and death rates, and HDI and its components were employed with a significance level of 0.05 using SPSS software. Results Lung cancer with standardized incidence rate (ASIR) and standardized mortality rate (ASMR), equal to 23.1 and 19.7 (in 100,000 people), respectively. The highest and lowest values of mortality incidence ratio (MIR) for lung cancer due to continents division were 0.93 and 0.71 for Eastern Africa and Australia/New Zealand, respectively. Univariate analysis showed significant relationship (P<0.0001) between ASIR and ASMR with life expectancy at birth and mean years of schooling. Conclusions The highest MIR for lung cancer was for medium human development countries. Linear regression analysis showed a reverse significant relationship between MIR and HDI. PMID:27293825

Epidemiology, incidence and mortality of lung cancer and their relationship with the development index in the world.

PubMed

Rafiemanesh, Hosein; Mehtarpour, Mojtaba; Khani, Farah; Hesami, Sayed Mohammadali; Shamlou, Reza; Towhidi, Farhad; Salehiniya, Hamid; Makhsosi, Behnam Reza; Moini, Ali

2016-06-01

The highest incidence of lung cancer is seen in North America and the lowest incidence in central Africa. Socioeconomic factors of inequality reflect regional disparities in human development. Due to the importance of awareness about incidence and mortality of lung cancer in health programming and the possible role of the human development index (HDI), this study was done with the aim to investigate the epidemiology of lung cancer in the world and its relationship with HDI. The study was conducted based on data from the world data of cancer and the World Bank (including the HDI and its components). Data about the age-specific incidence and mortality rate (ASR) for every country in 2012 were getting from the global cancer project. To analyze data, correlation tests between incidence and death rates, and HDI and its components were employed with a significance level of 0.05 using SPSS software. Lung cancer with standardized incidence rate (ASIR) and standardized mortality rate (ASMR), equal to 23.1 and 19.7 (in 100,000 people), respectively. The highest and lowest values of mortality incidence ratio (MIR) for lung cancer due to continents division were 0.93 and 0.71 for Eastern Africa and Australia/New Zealand, respectively. Univariate analysis showed significant relationship (P<0.0001) between ASIR and ASMR with life expectancy at birth and mean years of schooling. The highest MIR for lung cancer was for medium human development countries. Linear regression analysis showed a reverse significant relationship between MIR and HDI.

Population growth, human development, and deforestation in biodiversity hotspots.

PubMed

Jha, S; Bawa, K S

2006-06-01

Human population and development activities affect the rate of deforestation in biodiversity hotspots. We quantified the effect of human population growth and development on rates of deforestation and analyzed the relationship between these causal factors in the 1980s and 1990s. We compared the averages of population growth, human development index (HDI, which measures income, health, and education), and deforestation rate and computed correlations among these variables for countries that contain biodiversity hotspots. When population growth was high and HDI was low there was a high rate of deforestation, but when HDI was high, rate of deforestation was low, despite high population growth. The correlation among variables was significant for the 1990s but not for the 1980s. The relationship between population growth and HDI had a regional pattern that reflected the historical process of development. Based on the changes in HDI and deforestation rate over time, we identified two drivers of deforestation: policy choice and human-development constraints. Policy choices that disregard conservation may cause the loss of forests even in countries that are relatively developed. Lack of development in other countries, on the other hand, may increase the pressure on forests to meet the basic needs of the human population. Deforestation resulting from policy choices may be easier to fix than deforestation arising from human development constraints. To prevent deforestation in the countries that have such constraints, transfer of material and intellectual resources from developed countries may be needed. Popular interest in sustainable development in developed countries can facilitate the transfer of these resources.

The incidence and mortality of esophageal cancer and their relationship to development in Asia

PubMed Central

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Khosravi, Bahman; Soltani, Shahin; Pakzad, Iraj; Mohammadian, Mahdi; Momenimovahed, Zohre

2016-01-01

Background Esophageal cancer is the most common cancer in less developed countries. It is necessary to understand epidemiology of the cancer for planning. The aim of this study was to evaluate the incidence and mortality of esophageal cancer, and its relationship with Human Development Index (HDI) and its components in Asia in 2012. Methods This study was an Ecological study, which conducted based on GLOBOCAN project of WHO for Asian counters. We assess the correlation between standardized incidence rates (SIR) and standardized mortality rates (SMR) of esophageal cancer with HDI and its components with using of SPSS18. Results A total of 337,698 incidence (70.33% were males and 29.87% females. Sex ratio was 2.37) and 296,734 death (69.45% in men and 30.54% in women. The sex ratio was 2.27) esophageal cancer was recorded in Asian countries in 2012. Five countries with the highest SIR and SMR of esophageal cancer were Turkmenistan, Mongolia and Tajikistan, Bangladesh and China respectively. Correlation between HDI and SIR was −0.211 (P=0.159), in men −0.175 (P=0.244) and in women −0.231 (P=0.123). Also between HDI and SMR −0.250 (P=0.094) in men −0.226 (P=0.131) and in women −0.251 (P=0.037). Conclusions The incidence of esophageal cancer is more in less developed and developing countries. Statistically significant correlation was not found between standardized incidence and mortality rates of esophageal cancer, and HDI and its dimensions, except for life expectancy at birth. PMID:26889482

The incidence and mortality of esophageal cancer and their relationship to development in Asia.

PubMed

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Khosravi, Bahman; Soltani, Shahin; Pakzad, Iraj; Mohammadian, Mahdi; Salehiniya, Hamid; Momenimovahed, Zohre

2016-01-01

Esophageal cancer is the most common cancer in less developed countries. It is necessary to understand epidemiology of the cancer for planning. The aim of this study was to evaluate the incidence and mortality of esophageal cancer, and its relationship with Human Development Index (HDI) and its components in Asia in 2012. This study was an Ecological study, which conducted based on GLOBOCAN project of WHO for Asian counters. We assess the correlation between standardized incidence rates (SIR) and standardized mortality rates (SMR) of esophageal cancer with HDI and its components with using of SPSS18. A total of 337,698 incidence (70.33% were males and 29.87% females. Sex ratio was 2.37) and 296,734 death (69.45% in men and 30.54% in women. The sex ratio was 2.27) esophageal cancer was recorded in Asian countries in 2012. Five countries with the highest SIR and SMR of esophageal cancer were Turkmenistan, Mongolia and Tajikistan, Bangladesh and China respectively. Correlation between HDI and SIR was -0.211 (P=0.159), in men -0.175 (P=0.244) and in women -0.231 (P=0.123). Also between HDI and SMR -0.250 (P=0.094) in men -0.226 (P=0.131) and in women -0.251 (P=0.037). The incidence of esophageal cancer is more in less developed and developing countries. Statistically significant correlation was not found between standardized incidence and mortality rates of esophageal cancer, and HDI and its dimensions, except for life expectancy at birth.

Inequality in Human Development: An Empirical Assessment of 32 Countries

ERIC Educational Resources Information Center

Grimm, Michael; Harttgen, Kenneth; Klasen, Stephan; Misselhorn, Mark; Munzi, Teresa; Smeeding, Timothy

2010-01-01

One of the most frequent critiques of the HDI is that is does not take into account inequality within countries in its three dimensions. In this paper, we apply a simply approach to compute the three components and the overall HDI for quintiles of the income distribution. This allows a comparison of the level in human development of the poor with…

Mortality in Digestive Cancers, 2012: International Data and Data from Romania.

PubMed

Valean, Simona; Acalovschi, Monica; Diculescu, Mircea; Manuc, Mircea; Goldis, Adrian; Sfarti, Catalin; Trifan, Anca

2015-12-01

We aimed to compare the difference in case fatality rate between more developed and very high Human Development Index (HDI) regions, less developed and low HDI regions, and Romania. The incidence and mortality rates for digestive cancers were obtained from the IARC/WHO 2012 database. World mean mortality-to-incidence ratios registered the highest values in pancreatic cancer (0.97/0.94), and liver cancer (0.93/0.96) in males/females, respectively. The lowest values were recorded in colorectal cancer (0.48 in both sexes). Mortality-to-incidence ratios were generally higher in less developed areas, low HDI populations, and in Romania. The difference in case fatality rate between different areas showed higher variations for colorectal, gastric and gallbladder cancers, and smaller variations for esophageal, liver, and pancreatic cancers. In summary, mortality-to-incidence ratios of digestive cancers were high in 2012; higher values were registered in less developed and low HDI regions, and in Romania. Mortality-to-incidence ratios were similar in both sexes, even though the incidence was generally higher in men. Digestive cancer mortality variation suggests the necessity of finding better strategies for prevention, early diagnosis and treatment of digestive cancers.

From Politics to Parity: Using a Health Disparities Index to Guide Legislative Efforts for Health Equity

PubMed Central

Simpson, Sean L.; Hairston, Kristen G.

2011-01-01

Objectives. We created an index quantifying the longitudinal burden of racial health disparities by state and compared this index to variables to guide the construction of, and validate support for, legislative efforts aimed at eliminating health disparities. Methods. We evaluated 5 focus areas of greatest racial disparities in health from 1999 to 2005 and compiled state health disparities index (HDI) scores. We compared these scores with variables representing the purported social determinants of health. Results. Massachusetts (0.35), Oklahoma (0.35), and Washington (0.39) averaged the fewest disparities. Michigan (1.22), Wisconsin (1.32), and Illinois (1.50) averaged the greatest disparities. The statistical reference point for nationwide average racial disparities was 1.00. The longitudinal mixed model procedure yielded statistically significant correlations between HDI scores and Black state population percentage as well as with the racial gap in uninsured percentages. We noted a trend for HDI correlations with median household income ratios. Conclusions. On the basis of the HDI-established trends in the extent and distribution of racial health disparities, and their correlated social determinants of health, policymakers should consider incorporating this tool to advise future efforts in minority health legislation. PMID:21233445

Inequality in Human Development: An Empirical Assessment of 32 Countries

PubMed Central

Harttgen, Kenneth; Klasen, Stephan; Misselhorn, Mark; Munzi, Teresa; Smeeding, Timothy

2009-01-01

One of the most frequent critiques of the HDI is that is does not take into account inequality within countries in its three dimensions. In this paper, we apply a simply approach to compute the three components and the overall HDI for quintiles of the income distribution. This allows a comparison of the level in human development of the poor with the level of the non-poor within countries, but also across countries. This is an application of the method presented in Grimm et al. (World Development 36(12):2527–2546, 2008) to a sample of 21 low and middle income countries and 11 industrialized countries. In particular the inclusion of the industrialized countries, which were not included in the previous work, implies to deal with a number of additional challenges, which we outline in this paper. Our results show that inequality in human development within countries is high, both in developed and industrialized countries. In fact, the HDI of the lowest quintiles in industrialized countries is often below the HDI of the richest quintile in many middle income countries. We also find, however, a strong overall negative correlation between the level of human development and inequality in human development. PMID:20461123

Inhalation exposure to isocyanates of car body repair shop workers and industrial spray painters.

PubMed

Pronk, Anjoeka; Tielemans, Erik; Skarping, Gunnar; Bobeldijk, Ivana; VAN Hemmen, Joop; Heederik, Dick; Preller, Liesbeth

2006-01-01

As part of a large-scale epidemiological study, occupational isocyanate exposure was assessed in spray-painting environments. The aim was to assess which compounds contribute to isocyanate exposure in car body repair shops and industrial painting companies, and to identify tasks with high risk of isocyanate exposure. Mainly personal task-based samples (n = 566) were collected from 24 car body repair shops and five industrial painting companies using impingers with DBA in toluene. Samples were analysed by LC-MS for isocyanate monomers, oligomers and products of thermal degradation. From the 23 analysed compounds, 20 were detected. Exploratory factor analysis resulted in a HDI, TDI and MDI factor with the thermal degradation products divided over the TDI and MDI factors. The HDI factor mainly consisted of HDI oligomers and was dominant in frequency and exposure levels in both industries. Spray painting of PU lacquers resulted in the highest exposures for the HDI factor (

The impact of recirculating industrial air on aircraft painting operations.

PubMed

LaPuma, P T; Bolch, W E

1999-10-01

The 1990 Clean Air Act Amendments resulted in new environmental regulations for hazardous air pollutants. Industries such as painting facilities may have to treat large volumes of air, which increases the cost of an air control system. Recirculating a portion of the air back into the facility is an option to reduce the amount of air to be treated. The authors of this study developed a computer model written in Microsoft Excel 97 to analyze the impact of recirculation on worker safety and compliance costs. The model has a chemical database with over 1300 chemicals. The model will predict indoor air concentrations using mass balance calculations and results are compared to occupational exposure limits. A case study is performed on a C-130 aircraft painting facility at Hill Air Force Base, Utah. The model predicts strontium chromate concentrations found in primer paints will reach 1000 times the exposure limit. Strontium chromate and other solid particulates are nearly unaffected by recirculation because the air is filtered during recirculation. The next highest chemical, hexamethylene diisocyanate, increases from 2.6 to 10.5 times the exposure limit at 0 percent and 75 percent recirculation, respectively. Due to the level of respiratory protection required for the strontium chromate, workers are well protected from the modest increases in concentrations caused by recirculating 75 percent of the air. The initial cost of an air control system is $4.5 million with no recirculation and $1.8 million at 75 percent recirculation. The model is an excellent tool to evaluate air control options with a focus on worker safety. In the case study, the model highlights strontium chromate primers as good candidates for substitution. The model shows that recirculating 75 percent of the air at the Hill painting facility has a negligible impact on safety and could save $2.7 million on the initial expenses of a thermal treatment system.

Global Dental Research Productivity and Its Association With Human Development, Gross National Income, and Political Stability.

PubMed

Allareddy, Veerasathpurush; Allareddy, Veeratrishul; Rampa, Sankeerth; Nalliah, Romesh P; Elangovan, Satheesh

2015-09-01

The objective of this study is to examine the associations between country level factors (such as human development, economic productivity, and political stability) and their dental research productivity. This study is a cross-sectional analysis of bibliometric data from Scopus search engine. Human Development Index (HDI), Gross National Income per capita (GNI), and Failed State Index measures were the independent variables. Outcomes were "Total number of publications (articles or articles in press) in the field of dentistry" and "Total number of publications in the field of dentistry per million population." Non-parametric tests were used to examine the association between the independent and outcome variables. During the year 2013, a total of 11,952 dental research articles were published across the world. The top 5 publishing countries were United States, Brazil, India, Japan, and United Kingdom. "Very High" HDI countries had significantly higher number of total dental research articles and dental research articles per million population when compared to the "High HDI," "Medium HDI," and "Low HDI" countries (p < 0.0001). There was a significant linear relationship between the GNI quartile income levels and outcome metrics (p ≤ 0.007). Countries which were highly politically stable were associated with significantly higher dental research productivity (p < 0.0001). There appears to be a regional concentration of articles with just five countries contributing to over 50% of all articles. The human development and economic development of a country are linearly correlated with dental research productivity. Dental research productivity also increases with increasing political stability of a country. Copyright © 2015 Elsevier Inc. All rights reserved.

Phase II randomized trial comparing high-dose IFN-α2b with temozolomide plus cisplatin as systemic adjuvant therapy for resected mucosal melanoma.

PubMed

Lian, Bin; Si, Lu; Cui, Chuanliang; Chi, Zhihong; Sheng, Xinan; Mao, Lili; Li, Siming; Kong, Yan; Tang, Bixia; Guo, Jun

2013-08-15

Mucosal melanoma is rare and associated with extremely poor prognosis. However, standard adjuvant therapy for mucosal melanoma has not been established. We conducted a randomized phase II clinical trial in patients with resected mucosal melanoma to compare the efficacy and safety of high-dose IFN-α2b (HDI) and temozolomide-based chemotherapy as adjuvant therapy. Patients with mucosal melanoma in stage II/III after surgery were randomized into three groups: observation group (group A, surgery alone), HDI group (group B, treated with 15 × 10(6) U/m(2)/d IFN-α2b, followed by 9 × 10(6) U IFN-α2b), and temozolomide (200 mg/m(2)/d) plus cisplatin (75 mg/m(2)) group (group C). The endpoints were relapse-free survival (RFS), overall survival (OS), and toxicities. One hundred and eighty-nine patients were enrolled and finally analyzed. With a median follow-up of 26.8 months, the median RFS was 5.4, 9.4, and 20.8 months for group A, B, and C, respectively. Estimated median OS for group A, B, and C was 21.2, 40.4, and 48.7 months, respectively. Patients treated with temozolomide plus cisplatin showed significant improvements in RFS (P < 0.001) and OS (P < 0.01) than those treated with either HDI or surgery alone. Toxicities were generally mild to moderate. Both temozolomide-based chemotherapy and HDI are effective and safe as adjuvant therapies for resected mucosal melanoma as compared with observation alone. However, HDI tends to be less effective than temozolomide-based chemotherapy for patients with resected mucosal melanoma in respect to RFS. The temozolomide plus cisplatin regimen might be a better choice for patients with resected mucosal melanoma. ©2013 AACR.

Maternal life course socio-economic position and offspring body composition at birth in a multi-ethnic population.

PubMed

Sletner, Line; Jenum, Anne Karen; Mørkrid, Kjersti; Vangen, Siri; Holme, Ingar M; Birkeland, Kåre I; Nakstad, Britt

2014-09-01

Size and body composition at birth may affect long-term health. Mean birthweight and body composition differ between ethnic groups living in Europe. We wanted to explore if this relates to differences in socio-economic conditions in country of origin and over the maternal life course. This is a population-based cohort study of healthy pregnant women living in Oslo, Norway. Data on maternal early life and present socio-economic position (SEP) were collected in early gestation, and SEP scores were extracted through two separate principal components analyses. The associations between maternal present SEP and four different offspring anthropometric measures at birth were assessed separately, stratified by maternal early life SEP (dichotomised score) and Human Development Index (HDI, a country-level socio-economic indicator) in the country of origin [high HDI (Reference), n = 287 and low HDI, n = 250]. A strong positive association between maternal present SEP and offspring birthweight was observed if maternal early life SEP was high, but not if maternal early life SEP was low (P < 0.001 for the interaction term). This interactional effect was observed in both HDI groups. Maternal life course SEP affected offspring birthweight mainly through an effect on length and sum of skin folds. Offspring of mothers with origin from low HDI countries had smaller abdominal circumference, possibly indicating less fat-free mass, regardless of maternal life course SEP. Our results suggest that there are transgenerational effects of maternal past socio-economic conditions on offspring size and body composition at birth that modify the associations with present socio-economic factors. © 2014 John Wiley & Sons Ltd.

Country-Level Macroeconomic Indicators Predict Early Post-Allogeneic Hematopoietic Cell Transplantation Survival in Acute Lymphoblastic Leukemia: A CIBMTR Analysis.

PubMed

Wood, William A; Brazauskas, Ruta; Hu, Zhen-Huan; Abdel-Azim, Hisham; Ahmed, Ibrahim A; Aljurf, Mahmoud; Badawy, Sherif; Beitinjaneh, Amer; George, Biju; Buchbinder, David; Cerny, Jan; Dedeken, Laurence; Diaz, Miguel Angel; Freytes, Cesar O; Ganguly, Siddhartha; Gergis, Usama; Almaguer, David Gomez; Gupta, Ashish; Hale, Gregory; Hashmi, Shahrukh K; Inamoto, Yoshihiro; Kamble, Rammurti T; Adekola, Kehinde; Kindwall-Keller, Tamila; Knight, Jennifer; Kumar, Lalit; Kuwatsuka, Yachiyo; Law, Jason; Lazarus, Hillard M; LeMaistre, Charles; Olsson, Richard F; Pulsipher, Michael A; Savani, Bipin N; Schultz, Kirk R; Saad, Ayman A; Seftel, Matthew; Seo, Sachiko; Shea, Thomas C; Steinberg, Amir; Sullivan, Keith; Szwajcer, David; Wirk, Baldeep; Yared, Jean; Yong, Agnes; Dalal, Jignesh; Hahn, Theresa; Khera, Nandita; Bonfim, Carmem; Atsuta, Yoshiko; Saber, Wael

2018-03-19

For patients with acute lymphoblastic leukemia (ALL), allogeneic hematopoietic cell transplantation (alloHCT) offers a potential cure. Life-threatening complications can arise from alloHCT that require the application of sophisticated health care delivery. The impact of country-level economic conditions on post-transplantation outcomes is not known. Our objective was to assess whether these variables were associated with outcomes for patients transplanted for ALL. Using data from the Center for Blood and Marrow Transplant Research, we included 11,261 patients who received a first alloHCT for ALL from 303 centers across 38 countries between the years of 2005 and 2013. Cox regression models were constructed using the following macroeconomic indicators as main effects: Gross national income per capita, health expenditure per capita, and Human Development Index (HDI). The outcome was overall survival at 100 days following transplantation. In each model, transplants performed within lower resourced environments were associated with inferior overall survival. In the model with the HDI as the main effect, transplants performed in the lowest HDI quartile (n = 697) were associated with increased hazard for mortality (hazard ratio, 2.42; 95% confidence interval, 1.64 to 3.57; P < .001) in comparison with transplants performed in the countries with the highest HDI quartile. This translated into an 11% survival difference at 100 days (77% for lowest HDI quartile versus 88% for all other quartiles). Country-level macroeconomic indices were associated with lower survival at 100 days after alloHCT for ALL. The reasons for this disparity require further investigation. Copyright © 2018 The American Society for Blood and Marrow Transplantation. Published by Elsevier Inc. All rights reserved.

Association of Macroeconomic Factors With Nonrelapse Mortality After Allogeneic Hematopoietic Cell Transplantation for Adults With Acute Lymphoblastic Leukemia: An Analysis From the Acute Leukemia Working Party of the EBMT.

PubMed

Giebel, Sebastian; Labopin, Myriam; Ibatici, Adalberto; Browne, Paul; Czerw, Tomasz; Socie, Gerard; Unal, Ali; Kyrcz-Krzemien, Slawomira; Bacigalupo, Andrea; Goker, Hakan; Potter, Mike; Furness, Caroline L; McQuaker, Grant; Beelen, Dietrich; Milpied, Noel; Campos, Antonio; Craddock, Charles; Nagler, Arnon; Mohty, Mohamad

2016-03-01

From a global perspective, the rates of allogeneic hematopoietic cell transplantation (alloHCT) are closely related to the economic status of a country. However, a potential association with outcome has not yet been documented. The goal of this study was to evaluate effects of health care expenditure (HCE), Human Development Index (HDI), team density, and center experience on nonrelapse mortality (NRM) after HLA-matched sibling alloHCT for adults with acute lymphoblastic leukemia (ALL). A total of 983 patients treated with myeloablative alloHCT between 2004 and 2008 in 24 European countries were included. In a univariate analysis, the probability of day 100 NRM was increased for countries with lower current HCE (8% vs. 3%; p = .06), countries with lower HDI (8% vs. 3%; p = .02), and centers with less experience (8% vs. 5%; p = .04). In addition, the overall NRM was increased for countries with lower current HCE (21% vs. 17%; p = .09) and HDI (21% vs. 16%; p = .03) and for centers with lower activity (21% vs. 16%; p = .07). In a multivariate analysis, the strongest predictive model for day 100 NRM included current HCE greater than the median (hazard ratio [HR], 0.39; p = .002). The overall NRM was mostly predicted by HDI greater than the median (HR, 0.65; p = .01). Both lower current HCE and HDI were associated with decreased probability of overall survival. Both macroeconomic factors and the socioeconomic status of a country strongly influence NRM after alloHCT for adults with ALL. Our findings should be considered when clinical studies in the field of alloHCT are interpreted. ©AlphaMed Press.

Impact of human development on safety consciousness in construction.

PubMed

Baradan, Selim; Dikmen, Seyyit Umit; Akboga Kale, Ozge

2018-05-03

The International Labour Organization (ILO) reports that the risk of fatal occupational injuries in developing countries is almost twice as high as in developed countries, indicating a potential relationship between the fatality rates and the development level. The human development index (HDI), based on life expectancy, knowledge level and purchasing power parity, endorsed by the United Nations Development Programme, is a widely accepted measure of the development level. This study investigates the relationship between the HDI and the fatality rates reported by the ILO. A 23-country data set is used to demonstrate the general trend of the relationship followed by country-specific analyses for Australia, Spain, Hungary and Turkey. The study conducted is limited to fatal occupational injuries in construction, where the accidents are notoriously high. The results demonstrate a statistically significant inverse relationship between the fatality rates and the HDI.

Distribution of Brazilian dermatologists according to geographic location, population and HDI of municipalities: an ecological study*

PubMed Central

Schmitt, Juliano Vilaverde; Miot, Hélio Amante

2014-01-01

This study investigated the geographic distribution of dermatologists in Brazilian municipalities in relation to the population, regions of the country and human development index. We conducted an ecological study based on data from the 2010 census, the 2010 human development index, and the records of the Brazilian Society of Dermatology. 5565 municipalities and 6718 dermatologists were surveyed. Only 504 (9.1%) municipalities had dermatologists, and accounted for 56.2% of the Brazilian population. The smallest population size and lowest HDI rate that best discriminated municipalities that did not have dermatologists were found to be 28,000 and 0.71, respectively. The average population density of dermatologists in cities was 1/23.000 inhabitants, and variations were independently associated with the HDI, the population of the municipalities and the region of the country. PMID:25387516

Housing quality and access to material and learning resources within the home environment in developing countries.

PubMed

Bradley, Robert H; Putnick, Diane L

2012-01-01

This study examined home environment conditions (housing quality, material resources, formal and informal learning materials) and their relations with the Human Development Index (HDI) in 28 developing countries. Home environment conditions in these countries varied widely. The quality of housing and availability of material resources at home were consistently tied to HDI; the availability of formal and informal learning materials a little less so. Gross domestic product (GDP) tended to show a stronger independent relation with housing quality and material resources than life expectancy and education. Formal learning resources were independently related to the GDP and education indices, and informal learning resources were not independently related to any constituent indices of the overall HDI. © 2012 The Authors. Child Development © 2012 Society for Research in Child Development, Inc.

Advanced Fast Curing Adhesives for Adverse Conditions

DTIC Science & Technology

2007-07-01

experimentation. The catalyst is composed of 50% phthalate esters and 50% trivalent organic chromium complexes (15). 2.3 Aluminum Lap Plates...adhesives (2). Tape adhesives never provide weld - strength bonds and often have low tackiness when used underwater. Ultraviolet and visible light curable...diisocyanate and diphenylmethane-4, 4 diisocyanate (MDI) (12). The low viscosity ethyl cyanoacrylate Scotch- Weld CA40 was obtained from 3M of St

Protein adducts as biomarkers of exposure to aromatic diisocyanates in workers manufacturing polyurethane (PUR) foam.

PubMed

Säkkinen, Kirsi; Tornaeus, Jarkko; Hesso, Antti; Hirvonen, Ari; Vainio, Harri; Norppa, Hannu; Rosenberg, Christina

2011-04-01

This work was undertaken to investigate the usefulness of diisocyanate-related protein adducts in blood samples as biomarkers of occupational exposure to toluene diisocyanate (TDI; 2,4- and 2,6-isomers) and 4,4'-methylenediphenyl diisocyanate (MDI). Quantification of adducts as toluene diamines (TDAs) and methylenedianiline (MDA) was performed on perfluoroacylated derivatives by gas chromatography-mass spectrometry (GC-MS/MS) in negative chemical ionisation mode. TDI-derived adducts were found in 77% of plasma and in 59% of globin samples from exposed workers manufacturing flexible polyurethane foam. The plasma levels ranged from 0.003 to 0.58 nmol mL(-1) and those in globin from 0.012 to 0.33 nmol g(-1). The 2,6-isomer amounted to about two-thirds of the sum concentration of TDA isomers. MDI-derived adducts were detected in 3.5% of plasma and in 7% of globin samples from exposed workers manufacturing rigid polyurethane foam. A good correlation was found between the sum of TDA isomers in urine and that in plasma. The relationship between globin adducts and urinary metabolites was ambiguous. Monitoring TDI-derived TDA in plasma thus appears to be an appropriate method for assessing occupational exposure. Contrary to TDI exposure, adducts in plasma or globin were not useful in assessing workers' exposure to MDI. An important outcome of the study was that no amine-related adducts were detected in globin samples from TDI- or MDI-exposed workers, alleviating concerns that TDI or MDI might pose a carcinogenic hazard. Further studies are nevertheless required to judge whether diisocyanates per se could be such a hazard.

Biological monitoring of isocyanates and related amines. I. Determination of 1,6-hexamethylene diamine (HDA) in hydrolysed human urine after oral administration of HDA.

PubMed

Brorson, T; Skarping, G; Sandström, J F; Stenberg, M

1990-01-01

1,6-Hexamethylene diamine (HDA), used as raw material in industrial manufacturing operations, was orally administered to six healthy volunteers. After acid hydrolysis of the urine by hydrochloric acid, HDA and the metabolite 6-aminohexanoic acid were quantified. HDA was determined as an ethyl-chloroformate derivative by capillary gas chromatography using thermionic specific detection (TSD), and 6-aminohexanoic acid was quantified by ion chromatography using the ninhydrin reaction. In nonhydrolysed urine, monoacetylated HDA (N-acetyl-1,6-hexamethylene diamine) and HDA, were verified as heptafluorobutyric anhydride derivatives by gas chromatography-mass spectrometry (GC-MS), in a chemical ionization mode using isobutane and ammonia as reagent gases. In hydrolysed urine, a mean of 0.28 mg (range 1-6%) of the administered dose (8.2 mg) was recovered as HDA, and a mean of 0.8 mg (range less than 1-27%) as 6-aminohexanoic acid. The urinary excretion of both the determined compounds was rapid, and the principal part (greater than 90%) of the elimination was completed within 10 h. There was a considerable inter-individual variation in the excreted amounts, but the intra-individual variation in the excretion of HDA was limited. The subjects N-acetylator phenotype was determined by a dapsone test. Three slow acetylators excreted lower amounts (mean 2% of given dose) of HDA than three rapid ones (mean 5%).

Carbon Nanofiber Incorporated Silica Based Aerogels with Di-Isocyanate Cross-Linking

NASA Technical Reports Server (NTRS)

Vivod, Stephanie L.; Meador, Mary Ann B.; Capadona, Lynn A.; Sullivan, Roy M.; Ghosn, Louis J.; Clark, Nicholas; McCorkle, Linda

2008-01-01

Lightweight materials with excellent thermal insulating properties are highly sought after for a variety of aerospace and aeronautic applications. (1) Silica based aerogels with their high surface area and low relative densities are ideal for applications in extreme environments such as insulators for the Mars Rover battery. (2) However, the fragile nature of aerogel monoliths prevents their widespread use in more down to earth applications. We have shown that the fragile aerogel network can be cross-linked with a di-isocyanate via amine decorated surfaces to form a conformal coating. (3) This coating reinforces the neck regions between secondary silica particles and significantly strengthens the aerogels with only a small effect on density or porosity. Scheme 1 depicts the cross-linking reaction with the di-isocyanate and exhibits the stages that result in polymer cross-linked aerogel monoliths.

Retinoic acid, hemin and hexamethylen bisacetamide interference with "in vitro" differentiation of chick embryo chondrocytes.

PubMed

Manduca, P; Abelmoschi, M L

1992-01-01

We have investigated the effect of all-trans Retinoic acid, and of substances (Hemine and Hexamethylene bisacetamide) which interfere with "in vitro" differentiation of mesenchyme derived cell lineages on the expression of specific markers of hyperthrophy in "in vitro" differentiating chick embryo chondrocytes. (Castagnola P., et al., 1986). Continuous treatment of chondrogenic cells in conditions allowing differentiation "in vitro" with Retinoic acid resulted in persistence of type I collagen synthesis and in lack of type X collagen and Ch 21 protein expression. Hemin treated cells secreted a reduced amount of type X collagen. HMBA treatment inhibited type X collagen expression and caused reduction of the ratio between type II collagen and Ch 21 synthesized. The data indicate an independent regulation of these markers during chondrocyte differentiation.

Advantages and Challenges of 10-Gbps Transmission on High-Density Interconnect Boards

NASA Astrophysics Data System (ADS)

Yee, Chang Fei; Jambek, Asral Bahari; Al-Hadi, Azremi Abdullah

2016-06-01

This paper provides a brief introduction to high-density interconnect (HDI) technology and its implementation on printed circuit boards (PCBs). The advantages and challenges of implementing 10-Gbps signal transmission on high-density interconnect boards are discussed in detail. The advantages (e.g., smaller via dimension and via stub removal) and challenges (e.g., crosstalk due to smaller interpair separation) of HDI are studied by analyzing the S-parameter, time-domain reflectometry (TDR), and transmission-line eye diagrams obtained by three-dimensional electromagnetic modeling (3DEM) and two-dimensional electromagnetic modeling (2DEM) using Mentor Graphics HyperLynx and Keysight Advanced Design System (ADS) electronic computer-aided design (ECAD) software. HDI outperforms conventional PCB technology in terms of signal integrity, but proper routing topology should be applied to overcome the challenge posed by crosstalk due to the tight spacing between traces.

Effects of Youth Participation in Extra-Curricular Sport Programs on Perceived Self-Efficacy: A Multilevel Analysis.

PubMed

Reverdito, Riller S; Carvalho, Humberto M; Galatti, Larissa R; Scaglia, Alcides J; Gonçalves, Carlos E; Paes, Roberto R

2017-06-01

The present study examined extracurricular sport participation variables and developmental context in relationship to perceived self-efficacy among underserved adolescents. Participants ( n = 821, 13.6 ± 1.5 years) completed the Youth Experience in Sport questionnaire and General Self-Efficacy Scale. We used the Human Development Index (HDI) to characterize developmental contexts. Multilevel regression models were used to explore the relative contributions of age, sex, years of participation in extracurricular sport, HDI, and perceived positive experience in sport. Our results highlight that positive experience alone and in interaction with length of participation in the program fostered perceived self-efficacy. Participants from higher HDI contexts remained longer in the program. An implication of our research is that variables linked to positive sport experiences and perceived self-efficacy can be used as markers to evaluate the outcomes and impact of sport participation programs aimed at promoting positive youth development.

Molecular layer deposition of polyurethane-Polymerisation at the very contact to native aluminium and copper

NASA Astrophysics Data System (ADS)

Fug, Frank; Petry, Adrien; Jost, Hendrik; Ahmed, Aisha; Zamanzade, Mohammad; Possart, Wulff

2017-12-01

Thin layers of polyurethane monomers (diol, triol, diisocyanate) are deposited from gas phase onto native aluminium and copper surfaces. According to infrared external reflection absorption spectra both alcohols undergo only weak physical interactions with both metals. The diisocyanate on the other hand reveals resistance against desorption and rich new spectral features indicate strong adhesion. Preparation of urethane layers by sequential deposition of diisocyanate and diol yields urethane linkages. Urethane is formed faster on Cu than on Al. Scanning force microscopy reveals heterogeneous layers with metal dependent morphology. They show poor resistance against tetrahydrofuran rinsing i.e. most part of the formed urethane containing molecules are removed. Nevertheless, a residue of molecules sticks on the metal. It contains strongly adsorbed isocyanates and few isocyanate units which are bonded to diol units via urethane links. Further improvement of the molecular layer deposition is necessary to achieve well-crosslinked polyurethane layers.

Impact of stillbirths on international comparisons of preterm birth rates: a secondary analysis of the WHO multi-country survey of Maternal and Newborn Health.

PubMed

Morisaki, N; Ganchimeg, T; Vogel, J P; Zeitlin, J; Cecatti, J G; Souza, J P; Pileggi Castro, C; Torloni, M R; Ota, E; Mori, R; Dolan, S M; Tough, S; Mittal, S; Bataglia, V; Yadamsuren, B; Kramer, M S

2017-08-01

To evaluate the extent to which stillbirths affect international comparisons of preterm birth rates in low- and middle-income countries. Secondary analysis of a multi-country cross-sectional study. 29 countries participating in the World Health Organization Multicountry Survey on Maternal and Newborn Health. 258 215 singleton deliveries in 286 hospitals. We describe how inclusion or exclusion of stillbirth affect rates of preterm births in 29 countries. Preterm delivery. In all countries, preterm birth rates were substantially lower when based on live births only, than when based on total births. However, the increase in preterm birth rates with inclusion of stillbirths was substantially higher in low Human Development Index (HDI) countries [median 18.2%, interquartile range (17.2-34.6%)] compared with medium (4.3%, 3.0-6.7%), and high-HDI countries (4.8%, 4.4-5.5%). Inclusion of stillbirths leads to higher estimates of preterm birth rate in all countries, with a disproportionately large effect in low-HDI countries. Preterm birth rates based on live births alone do not accurately reflect international disparities in perinatal health; thus improved registration and reporting of stillbirths are necessary. Inclusion of stillbirths increases preterm birth rates estimates, especially in low-HDI countries. © 2017 World Health Organization, licensed by John Wiley & Sons Ltd on behalf of Royal College of Obstetricians and Gynaecologists.

Management of pegylated interferon alpha toxicity in adjuvant therapy of melanoma.

PubMed

Daud, Adil; Soon, Christopher; Dummer, Reinhard; Eggermont, Alexander M M; Hwu, Wen-Jen; Grob, Jean Jacques; Garbe, Claus; Hauschild, Axel

2012-08-01

Both native IFNα2b and pegylated IFNα2b (PegIFNα2b) are approved for the adjuvant treatment of high-risk melanoma. This review compares the toxicity profiles of high-dose IFNα2b (HDI) and PegIFNα2b, and provides recommendations on the management of common PegIFNα2b-related toxicities, based on available clinical data and published literature. The toxicity profile of PegIFNα2b at the approved dose (6 μg/kg/week for 8 weeks then 3 μg/kg/week for up to 5 years) is qualitatively similar to HDI in melanoma. The most common adverse events (AEs) are fatigue, anorexia, hepatotoxicity, flu-like symptoms, injection site reactions and depression. However, fatigue and flu-like symptoms appear less severe with PegIFNα2b, and toxicity seems to occur earlier, whereas with HDI toxicity may increase with time. Most AEs can be managed effectively by dose modification and aggressive symptom control. Dosing to tolerance using a three-step dose reduction schedule to maintain an ECOG performance status of 0 - 1 may enable patients experiencing toxicity to remain on treatment; this can be applied readily in clinical practice. PegIFNα2b is therefore a valuable alternative option for adjuvant treatment in melanoma, with a toxicity profile similar to that of HDI overall but a more convenient administration schedule.

Histone deacetylase inhibitor treatment induces ‘BRCAness’ and synergistic lethality with PARP inhibitor and cisplatin against human triple negative breast cancer cells

PubMed Central

Ha, Kyungsoo; Bhaskara, Srividya; Cerchietti, Leandro; Devaraj, Santhana G. T.; Shah, Bhavin; Sharma, Sunil; Chang, Jenny C.; Melnick, Ari M.; Hiebert, Scott; Bhalla, Kapil N.

2014-01-01

There is an unmet need to develop new, more effective and safe therapies for the aggressive forms of triple negative breast cancers (TNBCs). While up to 20% of women under 50 years of age with TNBC harbor germline mutations in BRCA1, and these tumors are sensitive to treatment with poly(ADP) ribose polymerase inhibitors, a majority of TNBCs lack BRCA1 mutations or loss of expression. Findings presented here demonstrate that by attenuating the levels of DNA damage response and homologous recombination proteins, pan-histone deacetylase inhibitor (HDI) treatment induces ‘BRCAness’ and sensitizes TNBC cells lacking BRCA1 to lethal effects of PARP inhibitor or cisplatin. Treatment with HDI also induced hyperacetylation of nuclear hsp90. Similar effects were observed following shRNA-mediated depletion of HDAC3, confirming its role as the deacetylase for nuclear HSP90. Furthermore, cotreatment with HDI and ABT-888 induced significantly more DNA strand breaks than either agent alone, and synergistically induced apoptosis of TNBC cells. Notably, co-treatment with HDI and ABT-888 significantly reduced in vivo tumor growth and markedly improved the survival of mice bearing TNBC cell xenografts. These findings support the rationale to interrogate the clinical activity of this novel combination against human TNBC, irrespective of its expression of mutant BRCA1. PMID:25026298

Incidence and Mortality of Nasopharynx Cancer and Its Relationship With Human Development Index in the World in 2012

PubMed Central

Mahdavifar, Neda; Towhidi, Farhad; Makhsosi, Behnam Reza; Pakzad, Reza; Moini, Ali; Ahmadi, Abbas; Lotfi, Sarah; Salehiniya, Hamid

2016-01-01

Background One of the most common cancers in head and neck is nasopharynx. Knowledge about the incidence and mortality of this disease and its distribution in terms of geographical areas is necessary for further study, better planning and prevention. Therefore, this study aimed to determine the incidence and mortality of nasopharynx cancer and its relationship with human development index (HDI) in the world in 2012. Methods This study was an ecological study conducted based on GLOBOCAN project of World Health Organization (WHO) for the countries in world. The correlation between standardized incidence rates (SIRs) and standardized mortality rates (SMRs) of nasopharynx cancer with HDI and its components was assessed with correlation coefficient by using SPSS 15. Results In 2012, 86,691 nasopharynx cancer cases occurred in the world, so that 60,896 new cases were seen in men and 25,795 new cases in women (sex ratio = 2.36). SIR of the cancer was 1.2 per 100,000 (1.7 in men and 0.7 in women per 100,000) in the world. In 2012, 50,831 nasopharynx death cases occurred in the world, so that 35,756 death cases were seen in men and 15,075 death cases in women (sex ratio = 2.37). SIR of mortality from the cancer was 0.7 per 100,000 (0.7 in women and 1 in men per 100,000) in the world. The results of correlation analysis showed a negative correlation between the SIR and HDI (r = -0.037, P = 0.629), and also the results of correlation analysis showed a negative correlation between the SMR and HDI (r = -0.237, P = 0.002). Conclusion Nasopharyngeal cancer is native to Southeast Asia and the highest incidence and mortality were seen in countries with moderate and low HDI. It is suggested that studies are conducted on determining the causes of the cancer incidence and mortality in the world and the differences between various regions. PMID:28983375

Female labour force participation and suicide rates in the world.

PubMed

Chen, Ying-Yeh; Chen, Mengni; Lui, Carrie S M; Yip, Paul S F

2017-12-01

The current study aims to illustrate male to female suicide rate ratios in the world and explore the correlations between female labour force participation rates (FLPR) and suicide rates of both genders. Further, whether the relationship of FLPR and suicide rates vary according to the human capabilities of a given country are examined. Using suicide data obtained from the World Health Organization Statistical Information System, suicide gender ratios of 70 countries are illustrated. Based on the level of Human Development Index (HDI) and FLPR, the Bayesian Information Criteria (BIC) was used to determine the optimal number of clusters of those countries. Graphic illustrations of FLPR and gender-specific suicide rates, stratified by each cluster were presented, and Pearson's correlation coefficients calculated. Three clusters are identified, there was no correlation between FLPR and suicide rates in the first cluster where both the HDI and FLPR were the highest (Male: r = 0.29, P = 0.45; Female: r = 0.01, P = 0.97); whereas in Cluster 2, higher level of FLPR corresponded to lower suicide rates in both genders, although the statistical significance was only found in females (Male: r = -0.32, P = 0.15; Female: r = -0.48, P = 0.03). In Cluster 3 countries where HDI/FLPR were relatively lower, increased FLPR was associated with higher suicide rates for both genders (Male: r = 0.32, P = 0.04; Female: r = 0.32, P = 0.05). The relationship between egalitarian gender norms and suicide rates varies according to national context. A greater egalitarian gender norms may benefit both genders, but more so for women in countries equipped with better human capabilities. Although the beneficial effect may reach a plateau in countries with the highest HDI/FLPR; whereas in countries with relatively lower HDI/FLPR, increased FLPR were associated with higher suicide rates. Copyright © 2017 Elsevier Ltd. All rights reserved.

Indigenous well-being in four countries: an application of the UNDP'S human development index to indigenous peoples in Australia, Canada, New Zealand, and the United States.

PubMed

Cooke, Martin; Mitrou, Francis; Lawrence, David; Guimond, Eric; Beavon, Dan

2007-12-20

Canada, the United States, Australia, and New Zealand consistently place near the top of the United Nations Development Programme's Human Development Index (HDI) rankings, yet all have minority Indigenous populations with much poorer health and social conditions than non-Indigenous peoples. It is unclear just how the socioeconomic and health status of Indigenous peoples in these countries has changed in recent decades, and it remains generally unknown whether the overall conditions of Indigenous peoples are improving and whether the gaps between Indigenous peoples and other citizens have indeed narrowed. There is unsettling evidence that they may not have. It was the purpose of this study to determine how these gaps have narrowed or widened during the decade 1990 to 2000. Census data and life expectancy estimates from government sources were used to adapt the Human Development Index (HDI) to examine how the broad social, economic, and health status of Indigenous populations in these countries have changed since 1990. Three indices - life expectancy, educational attainment, and income - were combined into a single HDI measure. Between 1990 and 2000, the HDI scores of Indigenous peoples in North America and New Zealand improved at a faster rate than the general populations, closing the gap in human development. In Australia, the HDI scores of Indigenous peoples decreased while the general populations improved, widening the gap in human development. While these countries are considered to have high human development according to the UNDP, the Indigenous populations that reside within them have only medium levels of human development. The inconsistent progress in the health and well-being of Indigenous populations over time, and relative to non-Indigenous populations, points to the need for further efforts to improve the social, economic, and physical health of Indigenous peoples.

Insensitive explosive composition and method of fracturing rock using an extrudable form of the composition

DOEpatents

Davis, Lloyd L

2013-11-05

Insensitive explosive compositions were prepared by reacting di-isocyanate and/or poly-isocyanate monomers with an explosive diamine monomer. Prior to a final cure, the compositions are extrudable. The di-isocyanate monomers tend to produce tough, rubbery materials while polyfunctional monomers (i.e. having more than two isocyanate groups) tend to form rigid products. The extrudable form of the composition may be used in a variety of applications including rock fracturing.

Insensitive explosive composition and method of fracturing rock using an extrudable form of the composition

DOEpatents

Davis, Lloyd L.

2015-07-28

Insensitive explosive compositions were prepared by reacting di-isocyanate and/or poly-isocyanate monomers with an explosive diamine monomer. Prior to a final cure, the compositions are extrudable. The di-isocyanate monomers tend to produce tough, rubbery materials while polyfunctional monomers (i.e. having more than two isocyanate groups) tend to form rigid products. The extrudable form of the composition may be used in a variety of applications including rock fracturing.

Evaluation of self-reported skin problems among workers exposed to toluene diisocyanate (TDI) at a foam manufacturing facility.

PubMed

Daftarian, Helga S; Lushniak, Boris D; Reh, Christopher M; Lewis, Daniel M

2002-12-01

Toluene diisocyanate, or TDI (CAS 584-84-9) is a well-known asthmagen and respiratory irritant. TDI is also known for its ability to irritate the skin and mucous membranes. To further investigate the dermal effects of TDI, NIOSH investigators conducted a cross-sectional study at a flexible foam manufacturing plant. A total of 114 workers participated in the study. Participants completed a medical questionnaire, provided blood for antibody testing to TDI and other allergens, and a subset of participants reporting skin symptoms underwent skin patch testing to a standard diisocyanate panel. Production line workers were more than twice as likely to report skin problems as those working in nonproduction areas (PRR = 2.66; 95% CI = 1.14-16.32; P = 0.02). Age, gender and duration of employment at the plant were comparable among participants working in production and nonproduction areas. Of the 100 participants who provided blood samples for antibody testing, specific IgG antibody to TDI was detected in two individuals, and none of the samples demonstrated specific IgE antibody to TDI. Of the 26 workers who underwent skin patch testing, none developed reactions to the diisocyanate allergens. These results suggest that the skin symptoms among study participants represent an irritant rather than an immunologic reaction to TDI, or to an unidentified allergen present in the foam.

A 15-Year Time-series Study of Tooth Extraction in Brazil

PubMed Central

Cunha, Maria Aparecida Goncalves de Melo; Lino, Patrícia Azevedo; dos Santos, Thiago Rezende; Vasconcelos, Mara; Lucas, Simone Dutra; de Abreu, Mauro Henrique Nogueira Guimarães

2015-01-01

Abstract Tooth loss is considered to be a public health problem. Time-series studies that assess the influence of social conditions and access to health services on tooth loss are scarce. This study aimed to examine the time-series of permanent tooth extraction in Brazil between 1998 and 2012 and to compare these series in municipalities with different Human Development Index (HDI) scores and with different access to distinct primary and secondary care. The time-series study was performed between 1998 and 2012, using data from the Brazilian National Health Information System. Time-series study was performed between 1998 and 2012. Two annual rates of tooth extraction were calculated and evaluated separately according to 3 parameters: the HDI, the presence of a Dental Specialty Center, and coverage by Oral Health Teams. The time-series was analyzed using a linear regression model. An overall decrease in the tooth-loss tendencies during this period was observed, particularly in the tooth-extraction rate during primary care procedures. In the municipalities with an HDI that was lower than the median, the average tooth-loss rates were higher than in the municipalities with a higher HDI. The municipalities with lower rates of Oral Health Team coverage also showed lower extraction rates than the municipalities with higher coverage rates. In general, Brazil has shown a decrease in the trend to extract permanent teeth during these 15 years. Increased human development and access to dental services have influenced tooth-extraction rates. PMID:26632688

[Secular trend of growth in stature in Florianópolis in the state of Santa Catarina (Brazil) in relation with the human development index (HDI)].

PubMed

Pinheiro, Andressa Caroline Carneiro; Niederauer, Juliana Minuzzi; Vargas, Deisi Maria

2014-01-01

The article seks to evaluate the secular trend of growth in stature of recruits in the 63rd Infantry Battalion in Florianópolis and correlate the information with the human development index (HDI). It involves a transversal and retrospective study of recruits aged between 18 and 20 who joined the 63rd IB in Florianópolis from 1963 to 2007. The sample comprised 600 individuals out of a total of 3000 recruits enlisted over the period. In each decade, three years were selected and within these years the first 40 files were systematically selected for analysis. It was seen that there was an increase in the order of 7 cm in height of recruits in Florianopolis over the past 47 years. This increase was more marked between the decades of 1990 and 2000, with the municipality of Blumenau having the highest average. The average heights study over the decades showed a strong positive correlation with the HDI of Florianopolis during the same period. When comparing the heights of the capital of Santa Catarina and previous studies in Blumenau, it was found that both cities have achieved the same increase of 1.4 cm/decade in the period between the 1960 and 2000. There was a positive secular trend in growth in Florianopolis, with a strong correlation with HDI values of the city between 1960 and 2000.

SOS response activation and competence development are antagonistic mechanisms in Streptococcus thermophilus.

PubMed

Boutry, Céline; Delplace, Brigitte; Clippe, André; Fontaine, Laetitia; Hols, Pascal

2013-02-01

Streptococcus includes species that either contain or lack the LexA-like repressor (HdiR) of the classical SOS response. In Streptococcus pneumoniae, a species which belongs to the latter group, SOS response inducers (e.g., mitomycin C [Mc] and fluoroquinolones) were shown to induce natural transformation, leading to the hypothesis that DNA damage-induced competence could contribute to genomic plasticity and stress resistance. Using reporter strains and microarray experiments, we investigated the impact of the SOS response inducers mitomycin C and norfloxacin and the role of HdiR on competence development in Streptococcus thermophilus. We show that both the addition of SOS response inducers and HdiR inactivation have a dual effect, i.e., induction of the expression of SOS genes and reduction of transformability. Reduction of transformability results from two different mechanisms, since HdiR inactivation has no major effect on the expression of competence (com) genes, while mitomycin C downregulates the expression of early and late com genes in a dose-dependent manner. The downregulation of com genes by mitomycin C was shown to take place at the level of the activation of the ComRS signaling system by an unknown mechanism. Conversely, we show that a ComX-deficient strain is more resistant to mitomycin C and norfloxacin in a viability plate assay, which indicates that competence development negatively affects the resistance of S. thermophilus to DNA-damaging agents. Altogether, our results strongly suggest that SOS response activation and competence development are antagonistic processes in S. thermophilus.

21 CFR 74.3102 - FD&C Blue No. 2.

Code of Federal Regulations, 2012 CFR

2012-04-01

... copolymer of adipic acid and hexamethylene diamine) surgical sutures for use in general surgery subject to... Food, Drug, and Cosmetic Act with respect to the medical device in which the color additive FD&C Blue...

21 CFR 74.3102 - FD&C Blue No. 2.

Code of Federal Regulations, 2011 CFR

2011-04-01

... copolymer of adipic acid and hexamethylene diamine) surgical sutures for use in general surgery subject to... Food, Drug, and Cosmetic Act with respect to the medical device in which the color additive FD&C Blue...

21 CFR 74.3102 - FD&C Blue No. 2.

Code of Federal Regulations, 2014 CFR

2014-04-01

... copolymer of adipic acid and hexamethylene diamine) surgical sutures for use in general surgery subject to... Food, Drug, and Cosmetic Act with respect to the medical device in which the color additive FD&C Blue...

21 CFR 74.3102 - FD&C Blue No. 2.

Code of Federal Regulations, 2013 CFR

2013-04-01

... copolymer of adipic acid and hexamethylene diamine) surgical sutures for use in general surgery subject to... Food, Drug, and Cosmetic Act with respect to the medical device in which the color additive FD&C Blue...

N-Acetyltransferase 2 Genotypes Are Associated With Diisocyanate-Induced Asthma.

PubMed

Yucesoy, Berran; Kissling, Grace E; Johnson, Victor J; Lummus, Zana L; Gautrin, Denyse; Cartier, André; Boulet, Louis-Philippe; Sastre, Joaquin; Quirce, Santiago; Tarlo, Susan M; Cruz, Maria-Jesus; Munoz, Xavier; Luster, Michael I; Bernstein, David I

2015-12-01

To investigate whether genetic variants of N-acetyltransferase (NAT) genes are associated with diisocyanate asthma (DA). The study population consisted of 354 diisocyanate-exposed workers. Genotyping was performed using a 5'-nuclease polymerase chain reaction assay. The NAT2 rs2410556 and NAT2 rs4271002 variants were significantly associated with DA in the univariate analysis. In the first logistic regression model comparing DA+ and asymptomatic worker groups, the rs2410556 (P = 0.004) and rs4271002 (P < 0.001) single nucleotide polymorphisms and the genotype combination, NAT2 rs4271002*NAT1 rs11777998, showed associations with DA risk (P = 0.014). In the second model comparing DA+ and DA- groups, NAT2 rs4271002 variant and the combined genotype, NAT1 rs8190845*NAT2 rs13277605, were significantly associated with DA risk (P = 0.022, P = 0.036, respectively). These findings suggest that variations in the NAT2 gene and their interactions contribute to DA susceptibility.

Polyurethane Binder Systems for Polymer Bonded Explosives

DTIC Science & Technology

2006-12-01

Propulsion (2005), Santiago , Chile . 8. Huang, C.-C., Hwu, W.-H., Cheng, C.-S., Shyy, I.-N., and Yang, K.-K., Study on Thermal Decomposition of Composite...water or amines to form ureas (Figure 2). R NCO R N C O H+ H2O O H R NH2 - CO2 R NCO R N C O NR’ H H ureaamine Figure 2. Reaction of an isocyanate...Monoisocyanates are present as impurities in low concentration in most diisocyanates. Table 1. Common diisocyanates Isocyanate Structure B.p. (ºC

“Pretty Pictures” with the HDI

NASA Astrophysics Data System (ADS)

Buckner, Spencer L.

2017-01-01

The Half-Degree Imager (HDI) has been in use on the 0.9-m WIYN telescope since October 2013. The instrument has well served the consortium as evidenced by the posters in this session and presentations at the concurrent special session held at this meeting. One thing that has been missing from the mix are aesthetically pleasing images for use in publicity and public outreach. Making “pretty pictures” with a scientific instrument such as HDI presents a number of challenges and opportunities. The chief challenge is finding the time to do the basic imaging given the limited telescope time available to users. Most users are understandably reluctant to take time away from imaging for their scientific research to take images whose primary purpose is to make a pretty picture. Fortunately, imaging of some objects to make pretty pictures can be done under sky conditions that are less than ideal when photometric studies would have limited usefulness. Another challenge is the raw HDI images must be converted from an extended FITS format into a normal FITS and a filter line added to the header to make the images usable by most commercially available image processing software. On the plus side, pretty picture images can serve to inspire prospective students into astronomy. Austin Peay State University has a popular astrophotography class that makes use of images taken with the HDI camera to introduce students to basic image processing techniques. The course is taken by both physics majors on the astrophysics track and non-science majors completing the astronomy minor. Pretty pictures can also be used as a recruitment tool to bring students into astronomy. APSU houses physics, biology, chemistry, agriculture and medical technology in the same building and displaying astronomical pictures at strategic locations around the building serves to recruit non-science majors to take more astronomy courses. Finally, the images can be used in publicity and outreach efforts by the university. This poster presents some of the techniques used in processing the images tor aesthetic value and how those images are used in recruitment, publicity and outreach. Several of the finished images in poster-sized prints will be available for viewing.

Adherence to a Healthy Diet According to the World Health Organization Guidelines and All-Cause Mortality in Elderly Adults From Europe and the United States

PubMed Central

Jankovic, Nicole; Geelen, Anouk; Streppel, Martinette T.; de Groot, Lisette C. P. G. M.; Orfanos, Philippos; van den Hooven, Edith H.; Pikhart, Hynek; Boffetta, Paolo; Trichopoulou, Antonia; Bobak, Martin; Bueno-de-Mesquita, H. B.; Kee, Frank; Franco, Oscar H.; Park, Yikyung; Hallmans, Göran; Tjønneland, Anne; May, Anne M.; Pajak, Andrzej; Malyutina, Sofia; Kubinova, Růžena; Amiano, Pilar; Kampman, Ellen; Feskens, Edith J.

2014-01-01

The World Health Organization (WHO) has formulated guidelines for a healthy diet to prevent chronic diseases and postpone death worldwide. Our objective was to investigate the association between the WHO guidelines, measured using the Healthy Diet Indicator (HDI), and all-cause mortality in elderly men and women from Europe and the United States. We analyzed data from 396,391 participants (42% women) in 11 prospective cohort studies who were 60 years of age or older at enrollment (in 1988–2005). HDI scores were based on 6 nutrients and 1 food group and ranged from 0 (least healthy diet) to 70 (healthiest diet). Adjusted cohort-specific hazard ratios were derived by using Cox proportional hazards regression and subsequently pooled using random-effects meta-analysis. During 4,497,957 person-years of follow-up, 84,978 deaths occurred. Median HDI scores ranged from 40 to 54 points across cohorts. For a 10-point increase in HDI score (representing adherence to an additional WHO guideline), the pooled adjusted hazard ratios were 0.90 (95% confidence interval (CI): 0.87, 0.93) for men and women combined, 0.89 (95% CI: 0.85, 0.92) for men, and 0.90 (95% CI: 0.85, 0.95) for women. These estimates translate to an increased life expectancy of 2 years at the age of 60 years. Greater adherence to the WHO guidelines is associated with greater longevity in elderly men and women in Europe and the United States. PMID:25318818

Advances in development reverse fertility declines.

PubMed

Myrskylä, Mikko; Kohler, Hans-Peter; Billari, Francesco C

2009-08-06

During the twentieth century, the global population has gone through unprecedented increases in economic and social development that coincided with substantial declines in human fertility and population growth rates. The negative association of fertility with economic and social development has therefore become one of the most solidly established and generally accepted empirical regularities in the social sciences. As a result of this close connection between development and fertility decline, more than half of the global population now lives in regions with below-replacement fertility (less than 2.1 children per woman). In many highly developed countries, the trend towards low fertility has also been deemed irreversible. Rapid population ageing, and in some cases the prospect of significant population decline, have therefore become a central socioeconomic concern and policy challenge. Here we show, using new cross-sectional and longitudinal analyses of the total fertility rate and the human development index (HDI), a fundamental change in the well-established negative relationship between fertility and development as the global population entered the twenty-first century. Although development continues to promote fertility decline at low and medium HDI levels, our analyses show that at advanced HDI levels, further development can reverse the declining trend in fertility. The previously negative development-fertility relationship has become J-shaped, with the HDI being positively associated with fertility among highly developed countries. This reversal of fertility decline as a result of continued economic and social development has the potential to slow the rates of population ageing, thereby ameliorating the social and economic problems that have been associated with the emergence and persistence of very low fertility.

Incidence and mortality of kidney cancer and its relationship with HDI (Human Development Index) in the world in 2012.

PubMed

Mohammadian, Maryam; Pakzad, Reza; Towhidi, Farhad; Makhsosi, Behnam Reza; Ahmadi, Abbas; Salehiniya, Hamid

2017-01-01

Kidney cancer is among the cancers that have the highest growth rate in all age and racial groups in the world and is as the most deadly type of urinary tract cancer. Since awareness about this cancer incidence status and mortality is essential for better planning, this study aimed to investigate the incidence and mortality rate of kidney cancer and its relationship with the development index in the world in 2012. This study was an ecological study conducted based on GLOBOCAN project of the World Health Organization (WHO) for the countries in the world. The correlation between Standardized Incidence Rates (SIRs) and Standardized Mortality Rates (SMRs) of kidney cancer with HDI and its components was assessed using SPSS18. In total, 337,860 incidence cases (213,924 were men and 123,936 women) and 143,406 deaths (90,802 cases in men and 52,604 in women) of kidney cancer were recorded in 2012. A positive correlation of 0.731 was seen between SIR of kidney cancer and HDI (p≤0.001). Also, a negative correlation of 0.627 was seen between SMR of kidney cancer and HDI (p≤0.001). The incidence and mortality rate of kidney cancer is higher in developed countries. A significant positive correlation has been seen between the standardized incidence and mortality rate of kidney cancer with the Human Development Index and its components. We need more studies to examine variation in incidence and mortality of kidney cancer and its related factors in the world.

Associations between meal and snack frequency and diet quality and adiposity measures in British adults: findings from the National Diet and Nutrition Survey.

PubMed

Murakami, Kentaro; Livingstone, M Barbara E

2016-06-01

To examine how different definitions of meals and snacks can affect the associations of meal frequency (MF) and snack frequency (SF) with dietary intake and adiposity measures. Based on 7 d weighed dietary record data, all eating occasions providing ≥210 kJ of energy were divided into meals or snacks based on contribution to energy intake (≥15 % or <15 %) or time (06.00-10.00, 12.00-15.00 and 18.00-21.00 hours; other). Diet quality was assessed using the Healthy Diet Indicator (HDI) and Mediterranean Diet Score (MDS). Great Britain. British adults aged 19-64 years (n 1487). MF based on energy contribution was associated with higher intake of dietary fibre, lower intakes of non-milk extrinsic sugars and alcohol, and higher HDI (only men) and MDS. MF based on time was associated with higher HDI and MDS in women only. Conversely, irrespective of the definition of snacks, SF was associated with higher intakes of confectionery and alcohol, lower intakes of cereals, protein, fat and dietary fibre, and lower HDI (except for SF based on energy contribution in women) and MDS. After adjustment for potential confounders, MF based on time, but not MF based on energy contribution, was positively associated with BMI and waist circumference in men only. SF was positively associated with BMI and waist circumference, irrespective of the definition of snacks. Higher SF was consistently associated with lower diet quality and higher adiposity measures, while associations with MF varied depending on the definition of meals and sex.

Provincial Human Development Index, a Guide for Efficiency Level Analysis: The Case of Iran

PubMed Central

SABERMAHANI, Asma; BAROUNI, Mohsen; SEYEDIN, Hesam; ARYANKHESAL, Aidin

2013-01-01

Background Human Development Index (HDI) is a composite indicator that can show the impact of economic strategies on human life standards. The index is calculated by three main factors of income, education and health. This research studies the status of HDI across the Iranian provinces, its changes over time and the efficiency of provinces in using resources. Methods: The data for 2001 and 2009 was obtained from the Iranian Center of Statistics. Data envelopment analysis technique was used to analyze the data. To calculate the efficiency, Banker, Charnes and Cooper’s model was used. Results: The national mean for the HDI in 2001 was 0.717 while it grew to 0.747 in 2009. Except for one province, all others had an improved human development index. Low ranked provinces such as Sistan & Baluchistan and Kurdistan stayed at the bottom in 2009 as well. Some provinces such as Bushehr with developing oil industries, or those purposively benefited from national oil income showed good growth. In some provinces, such as Hormozgan, out-migration of manpower to its neighboring province, Bushehr, was associated with decrease of the provincial income level. The number of efficient provinces increased from 5 to 13 in 2009. Conclusion: Iran falls among countries with high human development index based on the 2009 data. However, the distribution of HDI status across provinces was highly varied and the difference between high- and low-developed provinces increased in 2009. The government needs to revise policies concerning distribution of resources among the provinces. PMID:23515434

Gender gaps in life expectancy: generalized trends and negative associations with development indices in OECD countries.

PubMed

Liu, Yan; Arai, Asuna; Kanda, Koji; Lee, Romeo B; Glasser, Jay; Tamashiro, Hiko

2013-08-01

Life expectancy (LE) is a major marker of individual survival. It also serves as a guide to highlight both the progress and the gaps in total social and societal health. Comparative LE in concert with measures of gender-specific experience, indices of empowerment and societal happiness and development offer a comparative tool to examine trends and similarities of societal progress as seen through the lens of cross-national experience. To determine the gender gaps in LE (GGLE) trends, we performed a longitudinal analysis, covering a period of 49 years (1960-2008). To examine the association of GGLE with development indices, we used the 2007 GGLE data, the newest happiness data mostly drawn from 2006; the 2006 Human Development Index (HDI) data and the 2006 Gender Empowerment Measure (GEM) data. It revealed that most of the Organization for Economic Co-operation and Development (OECD) countries had a GGLE trend that occurred in an inverted U-curve fashion. We divided them into three subgroups based on the peak years of respective GGLE. The earlier the peak year, the happier the countries, the higher the HDI and the smaller the current GGLE are. Association analysis indicates that Happiness, HDI and GEM are all negatively associated with GGLE. This pattern suggests that GGLE undergoes three phases of growth, peak and stability and decline. Japan will soon be seeing its GGLE gradually shrinking in the foreseeable future. The continuing increases in Happiness, HDI and GEM are associated with a decrease in GGLE, which should be carefully taken into consideration.

Occupational exposure to diisocyanates in polyurethane foam factory workers.

PubMed

Świerczyńska-Machura, Dominika; Brzeźnicki, Sławomir; Nowakowska-Świrta, Ewa; Walusiak-Skorupa, Jolanta; Wittczak, Tomasz; Dudek, Wojciech; Bonczarowska, Marzena; Wesolowski, Wiktor; Czerczak, Sławomir; Pałczyński, Cezary

2015-01-01

The aim of the study was to evaluate health effects of occupational exposure to diisocyanates (DIC) among polyurethane foam products factory workers. Thirty workers had a physical examination, skin prick tests with common allergens, allergen-specific immunoglobulin E (IgE) antibodies to diisocyanates and pulmonary function tests. Concentrations of selected isocyanates in the workplace air samples as well as concentration of their metabolites in the urine samples collected from the workers of the plant were determined. The most frequent work-related symptoms reported by the examined subjects were rhinitis and skin symptoms. Sensitization to at least 1 common allergen was noted in 26.7% of the subjects. Spirometry changes of bronchial obstruction of a mild degree was observed in 5 workers. The specific IgE antibodies to toluene diisocyanate (TDI) and 4,4'-methylenebis(phenyl isocyanate) (MDI) were not detected in any of the patients' serum. Cellular profiles of the collected induced sputum (ISP) did not reveal any abnormalities. Air concentrations of TDI isomers ranged 0.2-58.9 μg/m3 and in 7 cases they exceeded the Combined Exposure Index (CEI) value for those compounds. Concentrations of TDI metabolites in post-shift urine samples were significantly higher than in the case of pre-shift urine samples and in 6 cases they exceeded the British Biological Monitoring Guidance Value (BMGV - 1 μmol amine/mol creatinine). We didn't find a correlation between urinary concentrations of TDI, concentrations in the air and concentrations of toluenediamine (TDA) in the post shift urine samples. Lack of such a correlation may be an effect of the respiratory protective equipment use. Determination of specific IgE in serum is not sensitive enough to serve as a biomarker. Estimation of concentrations of diisocyanate metabolites in urine samples and the presence of work-related allergic symptoms seem to be an adequate method for occupational exposure monitoring of DIC, which may help to determine workers at risk as well as to recognize hazardous workplaces. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

Biophysical determinants of toluene diisocyanate antigenicity associated with exposure and asthma.

PubMed

Ye, Young-Min; Kim, Cheol-Woo; Kim, Hyung-Ryul; Kim, Hyun-Mi; Suh, Chang-Hee; Nahm, Dong-Ho; Park, Hae-Sim; Redlich, Carrie A; Wisnewski, Adam V

2006-10-01

Toluene diisocyanate (TDI), a widely used aromatic diisocyanate with the potential to cause asthma, reacts with albumin in the airway fluid, which acts as a carrier protein for chemical presentation to the immune system. Structural elucidation of TDI-albumin conjugates is crucial to understanding the human immune response to TDI exposure. Investigate the dependence of TDI's antigenicity on the biophysics of exposure and its association with TDI asthma. Toluene diisocyanate-albumin conjugates were generated by exposing albumin to TDI in liquid or vapor phase (liquid or vapor TDI-albumin, respectively). Conjugates were characterized by native gel electrophoresis and matrix-assisted laser desorption/ionization-mass spectrometry, and used as antigens in ELISA assays for serum specific-IgE and IgG. The physical phase of TDI (vapor vs liquid) affects the formation of TDI-albumin conjugates, with measurable differences in the amount of TDI per albumin molecule, migration in native gels, matrix-assisted laser desorption/ionization-mass spectrometry mass/charge spectra, and antigenicity. Vapor TDI-albumin conjugates were recognized by IgE from 44% of subjects with TDI asthma, whereas liquid TDI-albumin conjugates are recognized by IgE from only 17% of these patients. A significant (P < .05) association between TDI exposure and vapor TDI-albumin specific serum IgG was also observed. Biophysics of TDI exposure substantially affects formation of TDI-albumin conjugates recognized by the immune system in association with exposure and asthma. The data suggest that serology may help identify TDI asthmatics and exposed workers if the appropriate form of TDI is used as the antigenic basis for analysis.

[Determination and analysis of toluene diisocyanate metabolites in mice using gas chromatography-mass spectrometry].

PubMed

Ji, Yu-Bin; Ji, Chen-Feng; Zou, Xiang; Liu, Hui-Xin

2007-09-01

In the present research we used gas chromatography-mass spectrometry (G C-MS) to determine metabolites of toluene diisocyanate (TDI) in mice and deduce the pathway for toluene diisocyanate metabolism in the organism. Conditions for TDI chromatography: Supelco PTETM-5 chromatographic column (30 mm x 0.25 mm x 0.25 microm); initial column temperature: 90 degrees C, which was maintained for 30 min, then the temperature was increased at a rate of 40 degrees C x min(-1) to 280 degrees C, and maintained for 5.25 min; temperature for the vaporizing chamber: 250 degrees C; carrier gas: helium flowing at 1.0 microL x min(-1). Conditions for chromatography of TDI metabolites in the organism: 94% methyl, 4% ethenyl-bonded-phase fused-silica capillary column (30 + 2 m x 0.25 + 0.02 mm); initial column temperature: 30 degrees C, which was maintained for 5 min, after and then was increased at a rate of 80 degrees C x min(-1) to 280 degrees C, and maintained for 5 min; temperature for the vaporizing chamber: 250 degrees C; carrier gas: helium flowing at 1.0 microL x min(-1). Conditions for mass spectrometry: EI for ionization; 70 eV for ionization energy; 280 degrees C for connecting tube temperature; 35-350 micro for range of scanning; and 1.0 microL for sample size. The results showed that 2 ,4-toluene diisocyanate was metabolized into 2,4-diaminotoluene. Under the conditions selected for GC-MS, TDI metabolites in the organism can be isolated and identified.

Isocyanate asthma: respiratory symptoms caused by diphenyl-methane di-isocyanate

PubMed Central

Tanser, A. R.; Bourke, M. P.; Blandford, A. G.

1973-01-01

Tanser, A. R., Bourke, M. P., and Blandford, A. G. (1973).Thorax, 28, 596-600. Isocyanate asthma: respiratory symptoms caused by diphenyl-methane di-isocyanate. We investigated 57 employees of a factory where diphenyl-methane di-isocyanate (MDI) was used to prepare the materials for making rigid polyurethane foam. Four employees had developed hypersensitivity to MDI. Two had severe, and one moderate asthma, while the fourth had symptoms resembling the delayed hypersensitivity type of reaction. Ten other employees had experienced unpleasant, mainly respiratory, irritant effects from MDI vapour. A past history of bronchitis or of allergy was found more commonly in those with symptoms from MDI than in those without symptoms. It is not known if MDI causes permanent damage to the respiratory tract. The most severely affected cases in the present series had normal spirometric values after recovery, and no persisting symptoms. MDI is safer than other isocyanates used in industry but may cause both major and minor illness. It should be handled with the same precautions as those used with the more toxic compounds. PMID:4784381

Di-Isocyanate Crosslinked Aerogels with 1, 6-Bis (Trimethoxysilyl) Hexane Incorporated in Silica Backbone

NASA Technical Reports Server (NTRS)

Vivod, Stephanie L.; Meador, Mary Ann B.; Nguyen, Baochau N.; Quade, Derek; Randall, Jason; Perry, Renee

2008-01-01

Silica aerogels are desirable materials for many applications that take advantage of their light weight and low thermal conductivity. Addition of a conformal polymer coating which bonds with the amine decorated surface of the silica network improves the strength of the aerogels by as much as 200 times. Even with vast improvement in strength they still tend to undergo brittle failure due to the rigid silica backbone. We hope to increase the flexibility and elastic recovery of the silica based aerogel by altering the silica back-bone by incorporation of more flexible hexane links. To this end, we investigated the use of 1,6-bis(trimethoxysilyl)hexane (BTMSH), a polysilsesquioxane precursor3, as an additional co-reactant to prepare silica gels which were subsequently cross-linked with di-isocyanate. Previously, this approach of adding flexibility by BTMSH incorporation was demonstrated with styrene cross-linked aerogels. In our study, we varied silane concentration, mol % of silicon from BTMSH and di-isocyanate concentration by weight percent to attempt to optimize both the flexibility and the strength of the aerogels.

[Determination of residual toluene diisocyanate in sponge bra by gas chromatography].

PubMed

Wang, Aixia; Ye, Ping; Huang, Nan; Chen, Yan; Li, Xinggen

2017-06-08

A gas chromatography (GC) with internal standard method was developed for the determination of residual toluene diisocyanate (TDI) in sponge bra. The samples were extracted with ethyl acetate dehydrated, and cleaned up with 0.22 μm microfiltration membrane. The residual toluene diisocyanate was separated on a DB-624 capillary column using temperature programming. The flame ionization detector (FID) was used at 250 ℃. The inlet temperature was 180 ℃ with nitrogen as carrier gas. The linear range was 10-200 mg/L ( R 2 =0.9989) for TDI. The average recovery ranged from 80.5% to 91.6% with RSD not more than 7.9%( n =6). The limit of detection (LOD) and limit of quantification (LOQ) were 10 mg/kg and 100 mg/kg, respectively. The developed method was then utilized to analyse the 100 batches of sponge bra samples from the manufacturing enterprises, the entity shops and electric business platforms. The method is simple, time-saving and environment friendly with high sensitivity and good reproducibility, and has practical application value due to its low-cost and short-circle.

Thermal degradation behavior and X-ray diffraction studies of chitosan based polyurethane bio-nanocomposites using different diisocyanates.

PubMed

Javaid, Muhammad Asif; Rizwan, Muhammad; Khera, Rasheed Ahmad; Zia, Khalid Mahmood; Saito, Kei; Zuber, Muhammad; Iqbal, Javed; Langer, Peter

2018-05-29

Five different samples of chitosan based polyurethane bio-nanocomposites (PUBNCs) were synthesized by step growth polymerization technique. Five different diisocyanates were used by keeping hydroxyl terminated polybutadiene (HTPB)/1,4-butane diol (1,4-BDO)/chitosan (CS) and montmorillonite (MMT) clay ratios constant (PUR1-PUR5). For comparative studies, PUR-6 was prepared without CS and clay components. Molecular characterizations of polyurethane (PU) films were carried out by FTIR and NMR which was found to have confirmatory evidence of the proposed structures. X-ray diffraction angles (2θ), d-spacing and intensities of chitosan based samples (PUR1-PUR5) and PUR-6 indicated that crystalline behavior of PUBNCs is influenced by varying diisocyanate structures. TGA/DTA results revealed that chitosan increased thermal stability of PU samples; it also enhanced the mechanical strength and decreased the glass transition temperature (T g ) of all the samples. Based on the above mentioned facts this study suggests the best usage of PUs according to the operational and environmental conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

Studies on the quality nutrition in women with polycystic ovary syndrome (PCOS)

PubMed

Szczuko, Małgorzata; Sankowska, Patrycja; Zapałowska-Chwyć, Marta; Wysokiński, Paweł

Polycystic ovary syndrome (PCOS) manifests itself with various symptoms, therefore it interests representatives of many medical specializations: general practitioners, gynecologists, endocrinologists, dermatologists, cardiologists and those who deal with metabolic disorders, such as dieticians. The aim of this study was perform the qualitative assessment of components of diets of women with PCOS as one of the major factor contributing to the disease. The study was performed on 54 women of childbearing age with PCOS diagnosed according to on the Rotterdam criteria. Qualitative assessment of the diets on the basis of 216 menus was performed based on the analysis of 3-day food diaries and food records taken from the last 24-hour dietary interview. Diets quality assessment was made using three types of point tests: Szewczyński’s Diets’ classification (SDC), Bielińska’s Test with Kulesza’s modification (BTK), Healthy Diet Indicator (HDI). Average waist-hip ratio (WHR) and body mass index (BMI) was above the standard 0.91± 0.08 and 29.16 ± 5.8 kg/m2. Qualitative analysis performed with point tests SDC, BT-K and HDI revealed that the majority of the diets were composed inappropriately, containing many mistakes. Statistically significant correlations (Pearson’s) were determined between HDI test and the body weight and BMI. When analyzing the type of the meals also the correlations (Spearman’s) between BMI and BMI category in BT-K test. Mistakes in diets of women with PCOS are the cause of metabolic disorders related to improper function of ovaries. Native test BT-K seems to be a better method then test SDC and probably HDI of assessing diet in women with PCOS from Poland.

Laryngeal cancer: Global socioeconomic trends in disease burden and smoking habits.

PubMed

Ramsey, Tam; Guo, Eric; Svider, Peter F; Lin, Hosheng; Syeda, Sara; Raza, S Naweed; Fribley, Andrew M

2018-03-06

To characterize health burden and determine the associated level of equality of laryngeal carcinoma (LC) burden at a global level. One hundred eighty-four countries were organized by socioeconomic status using Human Development Index (HDI) categorizations provided by the United Nations Development Program. Disability-adjusted life years (DALYs), obtained from The Global Health Data Exchange, were calculated and compared between each HDI category for the period from 1990 to 2015. Equality of LC burden was then evaluated with concentration indices. Global LC burden, as measured by age-standardized DALYs, has improved significantly over the 25-year period studied. This burden has declined for very high, high, and medium HDI countries, whereas it has remained unchanged for low HDI countries. The majority of LC global burden was found in high socioeconomic countries before 2010 and has shifted toward low socioeconomic countries, as indicated by concentration indices. Over the last 25 years, Central and Eastern Europe continue to have the largest disease burden in the world. This is the first analysis that we are aware of investigating health disparities of LC at a global level. The global burden of the disease has declined, which is a trend corresponding with significantly reduced smoking behaviors in developed countries. Although the global inequality gap decreased between 2010 and 2015, there remain reasons for concern. Smoking continues to trend upward in low socioeconomic countries, which could increase LC burden in low socioeconomic countries in the near future. A new global initiative directed toward low socioeconomic countries may yield dividends in preventing subsequent disparities in the LC burden. 4. Laryngoscope, 2017. © 2017 The American Laryngological, Rhinological and Otological Society, Inc.

Systematic review of the relationship of Helicobacter pylori infection with geographical latitude, average annual temperature and average daily sunshine.

PubMed

Lu, Chao; Yu, Ye; Li, Lan; Yu, Chaohui; Xu, Ping

2018-04-17

Helicobacter pylori (H. pylori) infection is a worldwide threat to human health with high prevalence. In this study, we analyzed the relationship between latitude, average annual temperature, average daily sunshine time and H. pylori infection. The PubMed, ClinicalTrials.gov , EBSCO and Web of Science databases were searched to identify studies reporting H. pylori infection. Latitude 30° was the cut-off level for low and mid-latitude areas. We obtained information for latitude, average annual temperature, average daily sunshine, and Human Development Index (HDI) from reports of studies of the relationships with H. pylori infection. Of the 51 studies included, there was significant difference in H. pylori infection between the low- and mid-latitude areas (P = 0.05). There was no significant difference in the prevalence of H. pylori infection in each 15°-latitude zone analyzed (P = 0.061). Subgroup analysis revealed the highest and lowest H. pylori infection rates in the developing regions at > 30° latitude subgroup and the developed regions at < 30° latitude subgroup, respectively (P < 0.001). Multivariate analysis showed that average annual temperature, average daily sunshine time and HDI were significantly correlated with H. pylori infection (P = 0.009, P < 0.001, P < 0.001), while there was no correlation between H. pylori infection and latitude. Our analysis showed that higher average annual temperature was associated with lower H. pylori infection rates, while average daily sunshine time correlated positively with H. pylori infection. HDI was also found to be a significant factor, with higher HDI associated with lower infection rates. These findings provide evidence that can be used to devise strategies for the prevention and control of H. pylori.

The International Epidemiology of Lung Cancer: Latest Trends, Disparities, and Tumor Characteristics

PubMed Central

Cheng, Ting-Yuan David; Cramb, Susanna M.; Baade, Peter D.; Youlden, Danny R.; Nwogu, Chukwumere; Reid, Mary E.

2017-01-01

Introduction We aim to update global lung cancer epidemiology and describe changing trends and disparities. Methods We presented country-specific incidence and mortality from GLOBOCAN 2012, by region and socioeconomic factors via the Human Development Index (HDI). Between- and within-country incidence by histological type was analyzed from Cancer Incidence in Five Continents Volume X (IARC). Trend analyses including the IARC data, cancer registries, and the WHO Mortality database were conducted using Joinpoint regression. Survival was compared between and within countries, and by histology. Results In 2012, there were 1.82 and 1.59 million new cases and deaths of lung cancer worldwide, respectively. Incidence was highest in very high HDI countries and lowest in low HDI countries (42.2 vs. 7.9/100,000 for males and 21.8 vs. 3.1/100,000 for females, respectively). In most countries with a very high HDI, as male incidence decreased gradually (ranging from −0.3% in Spain to −2.5% in the USA each year), female incidence continued to increase (by 1.4% each year in Australia to 6.1% in recent years in Spain). While histology varied between countries, adenocarcinoma was more common than squamous cell carcinoma, particularly among females (e.g., in Chinese females, the adenocarcinoma-to-squamous cell carcinoma ratio=6.6). Five-year relative survival varied from 2% (Libya) to 30% (Japan), with substantial within-country differences. Conclusion Lung cancer will continue to be a major health problem well through the first half of this century. Preventive strategies, particularly tobacco control, tailored to populations at highest risk are key to reduce the global burden of lung cancer. PMID:27364315

Inequality in Maternal Mortality in Iran: An Ecologic Study

PubMed Central

Tajik, Parvin; Nedjat, Saharnaz; Afshar, Nozhat Emami; Changizi, Nasrin; Yazdizadeh, Bahareh; Azemikhah, Arash; Aamrolalaei, Sima; Majdzadeh, Reza

2012-01-01

Background: Maternal mortality (MM) is an avoidable death and there is national, international and political commitment to reduce it. The objective of this study is to examine the relation of MM to socioeconomic factors and its inequality in Iran's provinces at an ecologic level. Methods: The overall MM from each province was considered for 3 years from 2004 to 2006. The five independent variables whose relations were studied included the literacy rate among men and women in each province, mean annual household income per capita, Gini coefficients in each province, and Human Development Index (HDI). The correlation of Maternal Mortality Ratio (MMR) to the above five variables was evaluated through Pearson's correlation coefficient (simple and weighted for each province's population) and linear regression – by considering MMR as the dependent variable and the Gini coefficient, HDI, and difference in literacy rate among men and women as the independent variables. Results: The mean MMR in the years 2004–2006 was 24.7 in 100,000 live births. The correlation coefficients between MMR and literacy rate among women, literacy rate among men, the mean annual household income per capita, Gini coefficient and HDI were 0.82, 0.90, –0.61, 0.52 and –0.77, respectively. Based on multivariate regression, MMR was significantly associated with HDI (standardized B=–0.93) and difference in literacy rate among men and women (standardized B=–0.47). However, MMR was not significantly associated with the Gini coefficient. Conclusion: This study shows the association between socioeconomic variables and their inequalities with MMR in Iran's provinces at an ecologic level. In addition to the other direct interventions performed to reduce MM, it seems essential to especially focus on more distal factors influencing MMR. PMID:22347608

Adherence to a healthy diet according to the World Health Organization guidelines and all-cause mortality in elderly adults from Europe and the United States.

PubMed

Jankovic, Nicole; Geelen, Anouk; Streppel, Martinette T; de Groot, Lisette C P G M; Orfanos, Philippos; van den Hooven, Edith H; Pikhart, Hynek; Boffetta, Paolo; Trichopoulou, Antonia; Bobak, Martin; Bueno-de-Mesquita, H B; Kee, Frank; Franco, Oscar H; Park, Yikyung; Hallmans, Göran; Tjønneland, Anne; May, Anne M; Pajak, Andrzej; Malyutina, Sofia; Kubinova, Růžena; Amiano, Pilar; Kampman, Ellen; Feskens, Edith J

2014-11-15

The World Health Organization (WHO) has formulated guidelines for a healthy diet to prevent chronic diseases and postpone death worldwide. Our objective was to investigate the association between the WHO guidelines, measured using the Healthy Diet Indicator (HDI), and all-cause mortality in elderly men and women from Europe and the United States. We analyzed data from 396,391 participants (42% women) in 11 prospective cohort studies who were 60 years of age or older at enrollment (in 1988-2005). HDI scores were based on 6 nutrients and 1 food group and ranged from 0 (least healthy diet) to 70 (healthiest diet). Adjusted cohort-specific hazard ratios were derived by using Cox proportional hazards regression and subsequently pooled using random-effects meta-analysis. During 4,497,957 person-years of follow-up, 84,978 deaths occurred. Median HDI scores ranged from 40 to 54 points across cohorts. For a 10-point increase in HDI score (representing adherence to an additional WHO guideline), the pooled adjusted hazard ratios were 0.90 (95% confidence interval (CI): 0.87, 0.93) for men and women combined, 0.89 (95% CI: 0.85, 0.92) for men, and 0.90 (95% CI: 0.85, 0.95) for women. These estimates translate to an increased life expectancy of 2 years at the age of 60 years. Greater adherence to the WHO guidelines is associated with greater longevity in elderly men and women in Europe and the United States. © The Author 2014. Published by Oxford University Press on behalf of the Johns Hopkins Bloomberg School of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Diet quality and adherence to a healthy diet in Japanese male workers with untreated hypertension.

PubMed

Kanauchi, Masao; Kanauchi, Kimiko

2015-07-10

As Japanese societies rapidly undergo westernisation, the prevalence of hypertension is increasing. We investigated the association between dietary quality and the prevalence of untreated hypertension in Japanese male workers. We conducted a cross-sectional study of 433 male workers who completed a brief food frequency questionnaire. Adherence to the WHO-based Healthy Diet Indicator (HDI), the American Heart Association 2006 Diet and Lifestyle Recommendations, the Dietary Approaches to Stop Hypertension (DASH) diet, and Mediterranean-style diet was assessed using four adherence indexes (HDI score, AI-84 score, DASH score and MED score). Hypertension classes were classified into three categories: non-hypertension, untreated hypertension and treated hypertension (ie, taking antihypertensive medication). The prevalence of untreated hypertension and treated hypertension was 22.4% and 8.5%, respectively. Patients with untreated hypertension had significantly lower HDI and AI-84 scores compared with non-hypertension. DASH and MED scores across the three hypertension classes were comparable. After adjusting for age, energy intake, smoking habit, alcohol drinking, physical activity and salt intake, a low adherence to HDI and a lowest quartile of AI-84 score were associated with a significantly higher prevalence of untreated hypertension, with an OR of 3.33 (95% CI 1.39 to 7.94, p=0.007) and 2.23 (1.09 to 4.53, p=0.027), respectively. A lower dietary quality was associated with increased prevalence of untreated hypertension in Japanese male workers. Our findings support a potential beneficial impact of nutritional assessment using diet qualities. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Dietary patterns in relation to quality-adjusted life years in the EPIC-NL cohort.

PubMed

Fransen, Heidi P; Beulens, Joline W J; May, Anne M; Struijk, Ellen A; Boer, Jolanda M A; de Wit, G Ardine; Onland-Moret, N Charlotte; van der Schouw, Yvonne T; Bueno-de-Mesquita, H Bas; Hoekstra, Jeljer; Peeters, Petra H M

2015-08-01

Dietary patterns have been associated with the incidence or mortality of individual non-communicable diseases, but their association with disease burden has received little attention. The aim of our study was to relate dietary patterns to health expectancy using quality-adjusted life years (QALYs) as outcome parameter. Data from the EPIC-NL study were used, a prospective cohort study of 33,066 healthy men and women aged 20-70 years at recruitment. A lifestyle questionnaire and a validated food frequency questionnaire were administered at study entry (1993-1997). Five dietary patterns were studied: three a priori patterns (the modified Mediterranean Diet Score (mMDS), the WHO-based Healthy Diet Indicator (HDI) and the Dutch Healthy Diet index (DHD-index)) and two a posteriori data-based patterns. QALYs were used as a summary health measure for healthy life expectancy, combining a person's life expectancy with a weight reflecting loss of quality of life associated with having chronic diseases. The mean QALYs of the participants were 74.9 (standard deviation 4.4). A higher mMDS and HDI were associated with a longer life in good health. Participants who had a high mMDS score (6-9) had 0.17 [95% CI, 0.05; 0.30] more QALYs than participants with a low score (0-3), equivalent to two months longer life in good health. Participants with a high HDI score also had more QALYs (0.15 [95% CI, 0.03; 0.27]) than participants with a low HDI score. A Mediterranean-type diet and the Healthy Diet Indicator were associated with approximately 2months longer life in good health. Copyright © 2015 Elsevier Inc. All rights reserved.

Incidence and Mortality of Liver Cancer and Their Relationship with Development in Asia.

PubMed

Mohammadian, Maryam; Soroush, Ali; Mohammadian-Hafshejani, Abdollah; Towhidi, Farhad; Hadadian, Fatemeh; Salehiniya, Hamid

2016-01-01

Liver cancer (LC) is the sixth world most common cancer and the second leading cause of cancer death. Due to the importance and necessity of awareness about the incidence and mortality of diseases to perform prevention programs, this study focused on data for LC and its relationship with the human development index (HDI) and its components in Asia in 2012. This ecological study was based on GLOBOCAN data for Asian countries. We assessed correlations between standardized incidence rates (SIR) and standardized mortality rates (SMR) of LC with HDI and its components using of SPSS18. A total of 582,420 incident cases and 557,097 deaths were recorded in Asian countries in 2012. The five with the highest SIR were Mongolia, Lao PDR, Vietnam, Republic of Korea and Thailand and those with the highest SMR were Mongolia, Lao PDR, Vietnam, Cambodia and Thailand. A negative relation was observed between HDI and LC for SIR of 0.049 (P=0.748) and for SMR of 0.07 (P=0.645), with life expectancy at birth a positive relation for SIR of 0.061 (P=0.687) and a negative relation for SMR of 0.079 (P=0.603), with the average years of education a negative relation fo SIR of 0.476 (p=0.952) and for SMR of 0.032 (P=0.832), and with the country income level per person a negative relation for SMI of 0.11 (p=0.465) and for SMR of 0.113 (P=0.455). The incidence of LC is more in less developed and developing countries but statistically significant correlations were not found between standardized incidence and mortality rates of LC, and HDI and its dimensions.

The incidence and mortality of lung cancer and their relationship to development in Asia.

PubMed

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Pakzad, Iraj; Salehiniya, Hamid

2015-12-01

Lung cancer is the deadliest cancer worldwide and the most common cancer in Asia. It is necessary to get information on epidemiology and inequalities related to incidence and mortality of the cancer to use for planning and further research. This study aimed to investigate epidemiology and inequality of incidence and mortality from lung cancer in Asia. The study was conducted based on data from the world data of cancer and the World Bank [including the Human Development Index (HDI) and its components]. The incidence and mortality rates, and cancer distribution maps were drawn for Asian countries. To analyze data, correlation test between incidence and death rates, and HDI and its components at significant was used in the significant level of 0.05 using SPSS software. A total of 1,033,881 incidence (71.13% were males and 28.87% were females. Sex ratio was 2.46) and 936,051 death (71.45% in men and 28.55% in women. The sex ratio was 2.50) recorded in Asian countries in 2012. Five countries with the highest standardized incidence and mortality rates of lung cancer were Democratic Republic of Korea, China, Armenia, Turkey, and Timor-Leste, respectively. Correlation between HDI and standardized incidence rate was 0.345 (P=0.019), in men 0.301 (P=0.042) and in women 0.3 (P=0.043); also between HDI and standardized mortality rate 0.289 (P=0.052), in men 0.265 (P=0.075) and in women 0.200 (P=0.182). The incidence of lung cancer has been increasing in Asia. It is high in men. Along with development, the incidence and mortality from lung cancer increases. It seems necessary to study reasons and factors of increasing the incidence and mortality of lung cancer in Asian countries.

Neglected tropical diseases in Brazil.

PubMed

Lindoso, José Angelo L; Lindoso, Ana Angélica B P

2009-01-01

Poverty is intrinsically related to the incidence of Neglected Tropical Diseases (NTDs). The main countries that have the lowest human development indices (HDI) and the highest burdens of NTDs are located in tropical and subtropical regions of the world. Among these countries is Brazil, which is ranked 70th in HDI. Nine out of the ten NTDs established by the World Health Organization (WHO) are present in Brazil. Leishmaniasis, tuberculosis, dengue fever and leprosy are present over almost the entire Brazilian territory. More than 90% of malaria cases occur in the Northern region of the country, and lymphatic filariasis and onchocerciasis occur in outbreaks in a particular region. The North and Northeast regions of Brazil have the lowest HDIs and the highest rates of NTDs. These diseases are considered neglected because there is not important investment in projects for the development of new drugs and vaccines and existing programs to control these diseases are not sufficient. Another problem related to NTDs is co-infection with HIV, which favors the occurrence of severe clinical manifestations and therapeutic failure. In this article, we describe the status of the main NTDs currently occurring in Brazil and relate them to the HDI and poverty.

Deep cultural ancestry and human development indicators across nation states

PubMed Central

Sookias, Roland B.; Passmore, Samuel

2018-01-01

How historical connections, events and cultural proximity can influence human development is being increasingly recognized. One aspect of history that has only recently begun to be examined is deep cultural ancestry, i.e. the vertical relationships of descent between cultures, which can be represented by a phylogenetic tree of descent. Here, we test whether deep cultural ancestry predicts the United Nations Human Development Index (HDI) for 44 Eurasian countries, using language ancestry as a proxy for cultural relatedness and controlling for three additional factors—geographical proximity, religion and former communism. While cultural ancestry alone predicts HDI and its subcomponents (income, health and education indices), when geographical proximity is included only income and health indices remain significant and the effect is small. When communism and religion variables are included, cultural ancestry is no longer a significant predictor; communism significantly negatively predicts HDI, income and health indices, and Muslim percentage of the population significantly negatively predicts education index, although the latter result may not be robust. These findings indicate that geographical proximity and recent cultural history—especially communism—are more important than deep cultural factors in current human development and suggest the efficacy of modern policy initiatives is not tightly constrained by cultural ancestry. PMID:29765628

[Environmental health and inequalities: building indicators for sustainable development].

PubMed

Carneiro, Fernando Ferreira; Franco Netto, Guilherme; Corvalan, Carlos; de Freitas, Carlos Machado; Sales, Luiz Belino Ferreira

2012-06-01

Despite its progress in terms of socio-economic indicators, Brazil is still unequal, which is due to an unequal and exclusionary historical process. In this paper we selected the Human Development Index - HDI and other social, economic, environmental and health indicators to exemplify this situation. We selected the municipalities that had the lowest HDI in the country in 2000 comparing their evolution over time between 2000 and 2010 by means of indicators linked to the economic, environmental and social pillars of sustainable development. These municipalities have an HDI classified as low (<0.500), and correspond to countries such as Laos, Yemen, Haiti and Madagascar. At national level, data for the decade show a significant improvement in economic indicators (decrease from 23% to 8.9% of people living on less than a quarter of the minimum wage); social indicators (increase from 86.5% to 90.2% of literacy in women), and the environmental indicator associated with access to the water grid, which also improved to a lesser extent (increase from 81% to 85%). It was concluded that in order to achieve sustainable development with quality of life, the improvement of sanitation and education indicators should be a priority for Brazil.

Deep cultural ancestry and human development indicators across nation states.

PubMed

Sookias, Roland B; Passmore, Samuel; Atkinson, Quentin D

2018-04-01

How historical connections, events and cultural proximity can influence human development is being increasingly recognized. One aspect of history that has only recently begun to be examined is deep cultural ancestry, i.e. the vertical relationships of descent between cultures, which can be represented by a phylogenetic tree of descent. Here, we test whether deep cultural ancestry predicts the United Nations Human Development Index (HDI) for 44 Eurasian countries, using language ancestry as a proxy for cultural relatedness and controlling for three additional factors-geographical proximity, religion and former communism. While cultural ancestry alone predicts HDI and its subcomponents (income, health and education indices), when geographical proximity is included only income and health indices remain significant and the effect is small. When communism and religion variables are included, cultural ancestry is no longer a significant predictor; communism significantly negatively predicts HDI, income and health indices, and Muslim percentage of the population significantly negatively predicts education index, although the latter result may not be robust. These findings indicate that geographical proximity and recent cultural history-especially communism-are more important than deep cultural factors in current human development and suggest the efficacy of modern policy initiatives is not tightly constrained by cultural ancestry.

Epidemiology and Inequality in the Incidence and Mortality of Nasopharynx Cancer in Asia.

PubMed

Mahdavifar, Neda; Ghoncheh, Mahshid; Mohammadian-Hafshejani, Abdollah; Khosravi, Bahman; Salehiniya, Hamid

2016-12-01

One of the most common head and neck cancers is nasopharynx cancer. Knowledge about the incidence and mortality of this disease and its distribution in terms of geographical areas is necessary for further study and better planning. Therefore, this study was conducted with the aim of determining the incidence and mortality rates of nasopharynx cancer and its relationship with the Human Development Index (HDI) in Asia in 2012. The aim of this ecologic study was to assess the correlation between age-specific incidence rate (ASIR) and age-specific mortality rate (ASMR) with HDI and its components, which include the following: life expectancy at birth, mean years of schooling, and gross national income per capita. Data about SIR and SMR for every Asian country for 2012 were obtained from the global cancer project. We used the correlation bivariate method for the assessment. Statistical significance was assumed if p  < 0.05. All reported p values are two-sided. Statistical analyses were performed using SPSS (Version 15.0, SPSS Inc.). A total of 68,272 cases (males, 71.02%; females, 28.97%; sex ratio, 2.45) and 40,530 mortalities (males, 71.63%; females, 28.36%; sex ratio, 2.52) were recorded in Asian countries in 2012. The five countries with the highest ASIR of nasopharynx cancer were Malaysia, Singapore, Indonesia, Vietnam, and Brunei, and the five countries with the highest ASMR were Indonesia, Vietnam, Singapore, Malaysia, and Brunei. The correlation between HDI and ASIR was 0.097 ( p  = 0.520) [0.105 in men ( p  = 0.488) and 0.119 in women ( p  = 0.901)]. The correlation between HDI and ASMR was -0.102 ( p  = 0.502) [-0.072 in men ( p  = 0.633) and -0.224 in women ( p  = 0.134)]. Nasopharynx cancer is native to Southeast Asia. The highest incidence and mortality rates are found in Malaysia, Singapore, Indonesia, Vietnam, and Brunei. No significant relation was found between the standardized incidence and mortality rates of nasopharynx cancer and the HDI components. Further studies are recommended in Southeast Asian countries in order to find the etiology of cancer, as well as its diagnosis and treatment.

Structure and Phase Transitions of Poly (Hexamethylene p,p'-Bibenzoate) as Studied by DSC and Real-Time SAXS/WAXS Employing Synchrotron Radiation

DOE Office of Scientific and Technical Information (OSTI.GOV)

Katerska, B.; Krasteva, M.; Perez, E.

2007-04-23

Real-time small and wide angle X-ray scattering as well as DSC studies were carried out in order to analyzes the structure and phase transitions of liquid crystalline thermotropic poly(methylene p,p' bibenzoat)

Precise Measurement of Refractive Index and Absorption Coefficient of Near Millimeter Wave and Far Infrared Materials.

DTIC Science & Technology

1987-06-01

polyethylene. The plexiglass is a polymethyl methacrylate and the acrylic is a polymethacrylate . The polyamide(nylon) is made with adipic acid and hexamethylene...are made with acrylic acid . It was not sur- prizing to see both exhibiting similar absorption characteristics atleast 30 times higher than

Associations between Caries among Children and Household Sugar Procurement, Exposure to Fluoridated Water and Socioeconomic Indicators in the Brazilian Capital Cities

PubMed Central

Gonçalves, Michele Martins; Leles, Cláudio Rodrigues; Freire, Maria do Carmo Matias

2013-01-01

The objective of this ecological study was to investigate the association between caries experience in 5- and 12-year-old Brazilian children in 2010 and household sugar procurement in 2003 and the effects of exposure to water fluoridation and socioeconomic indicators. Sample units were all 27 Brazilian capital cities. Data were obtained from the National Surveys of Oral Health; the National Household Food Budget Survey; and the United Nations Program for Development. Data analysis included correlation coefficients, exploratory factor analysis, and linear regression. There were significant negative associations between caries experience and procurement of confectionery, fluoridated water, HDI, and per capita income. Procurement of confectionery and soft drinks was positively associated with HDI and per capita income. Exploratory factor analysis grouped the independent variables by reducing highly correlated variables into two uncorrelated component variables that explained 86.1% of total variance. The first component included income, HDI, water fluoridation, and procurement of confectionery, while the second included free sugar and procurement of soft drinks. Multiple regression analysis showed that caries is associated with the first component. Caries experience was associated with better socioeconomic indicators of a city and exposure to fluoridated water, which may affect the impact of sugars on the disease. PMID:24307900

Inhibition of Major Drug Metabolizing CYPs by Common Herbal Medicines used by HIV/AIDS Patients in Africa– Implications for Herb-Drug Interactions

PubMed Central

Awortwe, Charles; Bouic, Patrick J.; Masimirembwa, Collen M.; Rosenkranz, Bernd

2015-01-01

The purpose of this study was to evaluate the potential risk of common herbal medicines used by HIV-infected patients in Africa for herb-drug interactions (HDI). High throughput screening assays consisting of recombinant Cytochrome P450 enzymes (CYPs) and fluorescent probes, and parallel artificial membrane permeability assays (PAMPA) were used. The potential of herbal medicines to cause HDI was ranked according to FDA guidelines for reversible inhibition and categorization of time dependent inhibition was based on the normalized ratio. CYPs 1A2 and 3A4 were most inhibited by the herbal extracts. H. hemerocallidea (IC50 = 0.63 μg/mL and 58 μg/mL) and E. purpurea (IC50 = 20 μg/mL and 12 μg/mL) were the potent inhibitors of CYPs 1A2 and 3A4 respectively. L. frutescens and H. hemerocallidea showed clear time dependent inhibition on CYP3A4. Furthermore, the inhibitory effect of both H. hemerocallidea and L. frutescens before and after PAMPA were identical. The results indicate potential HDI of H. hemerocallidea, L. frutescens and E. purpurea with substrates of the affected enzymes if maximum in vivo concentration is achieved. PMID:24475926

Head-disk interface nanotribology for Tbit/inch2 recording densities: near-contact and contact recording

NASA Astrophysics Data System (ADS)

Vakis, Antonis I.; Polycarpou, Andreas A.

2010-06-01

In the effort to achieve Tbit/inch2 recording densities, thermal fly-height control (TFC) nanotechnology was developed to effectively reduce the clearance (which is of the order of a few nanometres) at the head-disk interface (HDI) of hard-disk drives. In this work, we present a model of the HDI that can predict the dynamic flying and nanotribological contacting behaviour, allowing for accurate predictions and characterization of the operating regime as a function of TFC actuation. A geometric model for TFC is presented and an improved definition of contact at the interface is developed in the presence of nanoscale topographical roughness and dynamic microwaviness. A new methodology is proposed for the calculation of the nominal area of contact, which affects both near- and at-contact behaviour, while the stiffening of the air bearing force with TFC actuation is also accounted for. Slider behaviour is analysed by quantifying the approach, jump-to-contact, lubricant and solid contact regimes of operation and identifying the critical and optimum TFC actuations. The feasibility of near-contact, light molecularly thin lubricant contact versus solid contact recording is explored under the effect of the interfacial forces and stresses present at the HDI. The clearance and the state of vibrations are analysed and design guidelines are proposed for improved performance.

Suicide in developing countries (1): frequency, distribution, and association with socioeconomic indicators.

PubMed

Vijayakumar, Lakshmi; Nagaraj, K; Pirkis, Jane; Whiteford, Harvey

2005-01-01

Suicide is a global public health problem, but relatively little epidemiological investigation of the phenomenon has occurred in developing countries. This paper aims to (1) examine the availability of rate data in developing countries, (2) provide a description of the frequency and distribution of suicide in those countries for which data are available, and (3) explore the relationship between country-level socioeconomic factors and suicide rates. It is accompanied by two companion papers that consider risk factors and preventive efforts associated with suicide in developing countries, respectively. Using World Health Organization data, we calculated the average annual male, female, and total suicide rates during the 1990s for individual countries and regions (classified according to the Human Development Index [HDI]), and examined the association between a range of socioeconomic indicators and suicide rates. For reasons of data availability, we concentrated on medium HDI countries. Suicide rates in these countries were variable. They were generally comparable with those in high HDI countries from the same region, with some exceptions. High education levels, high telephone density, and high per capita levels of cigarette consumption were associated with high suicide rates; high levels of inequality were associated with low suicide rates. Epidemiological investigations of this kind have the potential to inform suicide prevention efforts in developing countries, and should be encouraged.

Global Inequalities in Cervical Cancer Incidence and Mortality are Linked to Deprivation, Low Socioeconomic Status, and Human Development

PubMed Central

Singh, Gopal K.; Azuine, Romuladus E.; Siahpush, Mohammad

2012-01-01

Objectives This study examined global inequalities in cervical cancer incidence and mortality rates as a function of cross-national variations in the Human Development Index (HDI), socioeconomic factors, Gender Inequality Index (GII), and healthcare expenditure. Methods Age-adjusted incidence and mortality rates were calculated for women in 184 countries using the 2008 GLOBOCAN database, and incidence and mortality trends were analyzed using the WHO cancer mortality database. Log-linear regression was used to model annual trends, while OLS and Poisson regression models were used to estimate the impact of socioeconomic and human development factors on incidence and mortality rates. Results Cervical cancer incidence and mortality rates varied widely, with many African countries such as Guinea, Zambia, Comoros, Tanzania, and Malawi having at least 10-to-20-fold higher rates than several West Asian, Middle East, and European countries, including Iran, Saudi Arabia, Syria, Egypt, and Switzerland. HDI, GII, poverty rate, health expenditure per capita, urbanization, and literacy rate were all significantly related to cervical cancer incidence and mortality, with HDI and poverty rate each explaining >52% of the global variance in mortality. Both incidence and mortality rates increased in relation to lower human development and higher gender inequality levels. A 0.2 unit increase in HDI was associated with a 20% decrease in cervical cancer risk and a 33% decrease in cervical cancer mortality risk. The risk of a cervical cancer diagnosis increased by 24% and of cervical cancer death by 42% for a 0.2 unit increase in GII. Higher health expenditure levels were independently associated with decreased incidence and mortality risks. Conclusions and Public Health Implications Global inequalities in cervical cancer are clearly linked to disparities in human development, social inequality, and living standards. Reductions in cervical cancer rates are achievable by reducing inequalities in socioeconomic conditions, availability of preventive health services, and women’s social status. PMID:27621956

Accuracy and precision of four value-added blood glucose meters: the Abbott Optium, the DDI Prodigy, the HDI True Track, and the HypoGuard Assure Pro.

PubMed

Sheffield, Catherine A; Kane, Michael P; Bakst, Gary; Busch, Robert S; Abelseth, Jill M; Hamilton, Robert A

2009-09-01

This study compared the accuracy and precision of four value-added glucose meters. Finger stick glucose measurements in diabetes patients were performed using the Abbott Diabetes Care (Alameda, CA) Optium, Diagnostic Devices, Inc. (Miami, FL) DDI Prodigy, Home Diagnostics, Inc. (Fort Lauderdale, FL) HDI True Track Smart System, and Arkray, USA (Minneapolis, MN) HypoGuard Assure Pro. Finger glucose measurements were compared with laboratory reference results. Accuracy was assessed by a Clarke error grid analysis (EGA), a Parkes EGA, and within 5%, 10%, 15%, and 20% of the laboratory value criteria (chi2 analysis). Meter precision was determined by calculating absolute mean differences in glucose values between duplicate samples (Kruskal-Wallis test). Finger sticks were obtained from 125 diabetes patients, of which 90.4% were Caucasian, 51.2% were female, 83.2% had type 2 diabetes, and average age of 59 years (SD 14 years). Mean venipuncture blood glucose was 151 mg/dL (SD +/-65 mg/dL; range, 58-474 mg/dL). Clinical accuracy by Clarke EGA was demonstrated in 94% of Optium, 82% of Prodigy, 61% of True Track, and 77% of the Assure Pro samples (P < 0.05 for Optium and True Track compared to all others). By Parkes EGA, the True Track was significantly less accurate than the other meters. Within 5% accuracy was achieved in 34%, 24%, 29%, and 13%, respectively (P < 0.05 for Optium, Prodigy, and Assure Pro compared to True Track). Within 10% accuracy was significantly greater for the Optium, Prodigy, and Assure Pro compared to True Track. Significantly more Optium results demonstrated within 15% and 20% accuracy compared to the other meter systems. The HDI True Track was significantly less precise than the other meter systems. The Abbott Optium was significantly more accurate than the other meter systems, whereas the HDI True Track was significantly less accurate and less precise compared to the other meter systems.

Biosphere as a complex life-support system (LSS) for human civilization

NASA Astrophysics Data System (ADS)

Pechurkin, Nickolay

As a continuously growing link of the Biosphere, we should keep in mind that biotic cycles induced by flows of a solar energy are the source of Biosphere and ecosystems functioning. Our pressure on the Biosphere which is connected with biotic cycle’s alterations and damages is menacingly growing. There are innumerable examples of atmosphere, water and soil pollution. We have contaminated even Earth-Space orbits with different uncontrolled debris. Ecological Footprint (EF) is a proper quantitative measure of anthropogenic impact on the Biosphere and ecosystems functioning. The comparative dynamics of the United Nations’ Human Development Index (HDI) and Ecological Footprint (EF) is discussed in the paper. The main call of sustainable development of mankind: all humans can have opportunity to fulfill their lives without degrading the Biosphere. To support sustainability, we should make an effort to develop each nation and the mankind as a whole with a high HDI and with a low ecological footprint. It means: to have high level of HDI at low level of EF. But current tendency of economical and social development shows: the higher HDI, the bigger EF. EF of mankind is rising threateningly. Now actual pressure of the human civilization of our planet (2014) upon 60 % exceeds its potential possibilities (biological capacity, measured as the area of "global" green hectares). It means that now we require more than 1.5 planets of the Earth’s type for sustainable development. It leads to ecological incident in the scale of Biosphere. Our Biosphere is the large, multilevel, hierarchically organized system, and our civilization is only a part of it. This part is not central; it can disappear for ever, if we do not cope to be included in the Biosphere as a great complex system. An example of Krasnoyarsk region as a representative region with high level of industry and technological energy production is considered in the paper. This work was supported by the Russian Foundation for Basic Research, project number 13-06-00060.

Alcoholic Beverage Preference and Dietary Habits in Elderly across Europe: Analyses within the Consortium on Health and Ageing: Network of Cohorts in Europe and the United States (CHANCES) Project

PubMed Central

Sluik, Diewertje; Jankovic, Nicole; O’Doherty, Mark G.; Geelen, Anouk; Schöttker, Ben; Rolandsson, Olov; Kiefte-de Jong, Jessica C.; Ferrieres, Jean; Bamia, Christina; Fransen, Heidi P.; Boer, Jolanda M. A.; Eriksson, Sture; Martínez, Begoña; Huerta, José María; Kromhout, Daan; de Groot, Lisette C. P. G. M.; Franco, Oscar H.; Trichopoulou, Antonia; Boffetta, Paolo; Kee, Frank; Feskens, Edith J. M.

2016-01-01

Introduction The differential associations of beer, wine, and spirit consumption on cardiovascular risk found in observational studies may be confounded by diet. We described and compared dietary intake and diet quality according to alcoholic beverage preference in European elderly. Methods From the Consortium on Health and Ageing: Network of Cohorts in Europe and the United States (CHANCES), seven European cohorts were included, i.e. four sub-cohorts from EPIC-Elderly, the SENECA Study, the Zutphen Elderly Study, and the Rotterdam Study. Harmonized data of 29,423 elderly participants from 14 European countries were analyzed. Baseline data on consumption of beer, wine, and spirits, and dietary intake were collected with questionnaires. Diet quality was assessed using the Healthy Diet Indicator (HDI). Intakes and scores across categories of alcoholic beverage preference (beer, wine, spirit, no preference, non-consumers) were adjusted for age, sex, socio-economic status, self-reported prevalent diseases, and lifestyle factors. Cohort-specific mean intakes and scores were calculated as well as weighted means combining all cohorts. Results In 5 of 7 cohorts, persons with a wine preference formed the largest group. After multivariate adjustment, persons with a wine preference tended to have a higher HDI score and intake of healthy foods in most cohorts, but differences were small. The weighted estimates of all cohorts combined revealed that non-consumers had the highest fruit and vegetable intake, followed by wine consumers. Non-consumers and persons with no specific preference had a higher HDI score, spirit consumers the lowest. However, overall diet quality as measured by HDI did not differ greatly across alcoholic beverage preference categories. Discussion This study using harmonized data from ~30,000 elderly from 14 European countries showed that, after multivariate adjustment, dietary habits and diet quality did not differ greatly according to alcoholic beverage preference. PMID:27548323

The incidence and mortality of lung cancer and their relationship to development in Asia

PubMed Central

Pakzad, Reza; Mohammadian-Hafshejani, Abdollah; Ghoncheh, Mahshid; Pakzad, Iraj

2015-01-01

Background Lung cancer is the deadliest cancer worldwide and the most common cancer in Asia. It is necessary to get information on epidemiology and inequalities related to incidence and mortality of the cancer to use for planning and further research. This study aimed to investigate epidemiology and inequality of incidence and mortality from lung cancer in Asia. Methods The study was conducted based on data from the world data of cancer and the World Bank [including the Human Development Index (HDI) and its components]. The incidence and mortality rates, and cancer distribution maps were drawn for Asian countries. To analyze data, correlation test between incidence and death rates, and HDI and its components at significant was used in the significant level of 0.05 using SPSS software. Results A total of 1,033,881 incidence (71.13% were males and 28.87% were females. Sex ratio was 2.46) and 936,051 death (71.45% in men and 28.55% in women. The sex ratio was 2.50) recorded in Asian countries in 2012. Five countries with the highest standardized incidence and mortality rates of lung cancer were Democratic Republic of Korea, China, Armenia, Turkey, and Timor-Leste, respectively. Correlation between HDI and standardized incidence rate was 0.345 (P=0.019), in men 0.301 (P=0.042) and in women 0.3 (P=0.043); also between HDI and standardized mortality rate 0.289 (P=0.052), in men 0.265 (P=0.075) and in women 0.200 (P=0.182). Conclusions The incidence of lung cancer has been increasing in Asia. It is high in men. Along with development, the incidence and mortality from lung cancer increases. It seems necessary to study reasons and factors of increasing the incidence and mortality of lung cancer in Asian countries. PMID:26798586

Global Inequalities in Cervical Cancer Incidence and Mortality are Linked to Deprivation, Low Socioeconomic Status, and Human Development.

PubMed

Singh, Gopal K; Azuine, Romuladus E; Siahpush, Mohammad

2012-01-01

This study examined global inequalities in cervical cancer incidence and mortality rates as a function of cross-national variations in the Human Development Index (HDI), socioeconomic factors, Gender Inequality Index (GII), and healthcare expenditure. Age-adjusted incidence and mortality rates were calculated for women in 184 countries using the 2008 GLOBOCAN database, and incidence and mortality trends were analyzed using the WHO cancer mortality database. Log-linear regression was used to model annual trends, while OLS and Poisson regression models were used to estimate the impact of socioeconomic and human development factors on incidence and mortality rates. Cervical cancer incidence and mortality rates varied widely, with many African countries such as Guinea, Zambia, Comoros, Tanzania, and Malawi having at least 10-to-20-fold higher rates than several West Asian, Middle East, and European countries, including Iran, Saudi Arabia, Syria, Egypt, and Switzerland. HDI, GII, poverty rate, health expenditure per capita, urbanization, and literacy rate were all significantly related to cervical cancer incidence and mortality, with HDI and poverty rate each explaining >52% of the global variance in mortality. Both incidence and mortality rates increased in relation to lower human development and higher gender inequality levels. A 0.2 unit increase in HDI was associated with a 20% decrease in cervical cancer risk and a 33% decrease in cervical cancer mortality risk. The risk of a cervical cancer diagnosis increased by 24% and of cervical cancer death by 42% for a 0.2 unit increase in GII. Higher health expenditure levels were independently associated with decreased incidence and mortality risks. Global inequalities in cervical cancer are clearly linked to disparities in human development, social inequality, and living standards. Reductions in cervical cancer rates are achievable by reducing inequalities in socioeconomic conditions, availability of preventive health services, and women's social status.

Epidemiology, Incidence and Mortality of Bladder Cancer and their Relationship with the Development Index in the World.

PubMed

Mahdavifar, Neda; Ghoncheh, Mahshid; Pakzad, Reza; Momenimovahed, Zohre; Salehiniya, Hamid

2016-01-01

Bladder cancer is an international public health problem. It is the ninth most common cancer and the fourteenth leading cause of death due to cancer worldwide. Given aging populations, the incidence of this cancer is rising. Information on the incidence and mortality of the disease, and their relationship with level of economic development is essential for better planning. The aim of the study was to investigate bladder cancer incidence and mortality rates, and their relationship with the the Human Development Index (HDI) in the world. Data were obtained from incidence and mortality rates presented by GLOBOCAN in 2012. Data on HDI and its components were extracted from the global bank site. The number and standardized incidence and mortality rates were reported by regions and the distribution of the disease were drawn in the world. For data analysis, the relationship between incidence and death rates, and HDI and its components was measured using correlation coefficients and SPSS software. The level of significance was set at 0.05. In 2012, 429,793 bladder cancer cases and 165,084 bladder death cases occurred in the world. Five countries that had the highest age-standardized incidence were Belgium 17.5 per 100,000, Lebanon 16.6/100,000, Malta 15.8/100,000, Turkey 15.2/100,000, and Denmark 14.4/100,000. Five countries that had the highest age-standardized death rates were Turkey 6.6 per 100,000, Egypt 6.5/100,000, Iraq 6.3/100,000, Lebanon 6.3/100,000, and Mali 5.2/100,000. There was a positive linear relationship between the standardized incidence rate and HDI (r=0.653, P<0.001), so that there was a positive correlation between the standardized incidence rate with life expectancy at birth, average years of schooling, and the level of income per person of population. A positive linear relationship was also noted between the standardized mortality rate and HDI (r=0.308, P<0.001). There was a positive correlation between the standardized mortality rate with life expectancy at birth, average years of schooling, and the level of income per person of population. The incidence of bladder cancer in developed countries and parts of Africa was higher, while the highest mortality rate was observed in the countries of North Africa and the Middle East. The program for better treatment in developing countries to reduce mortality from the cancer and more detaiuled studies on the etiology of are essential.

Isocyanate-induced asthma in a car factory.

PubMed

White, W G; Morris, M J; Sugden, E; Zapata, E

1980-04-05

In a car factory employing 203 women machinists making seat covers more women complained of respiratory symptoms after the introduction of a new seat cover fabric, cropped nylon backed with flame-bonded polyurethane foam (CNPF). 68 women working in the trim shop were studied on the first day back at work after a week's holiday and then at the end of a working week; the incidence of wheezing and/or shortness of breath was greater than expected but there was no difference between peak flow rates. A second study of 192 of the 203 women working in the trim shop confirmed this recent increase in incidence of asthmatic symptoms and showed that significantly more machinists who had worked with this new fabric had a reduced peak flow rate than machinists who had not. Asthma developed in one subject when she was working in the factory sewing CNPF, when she was handling this fabric in the challenge cabinet in the laboratory, and on challenge with toluene di-isocyanate in the laboratory. Airways resistance increased in 3 other workers after exposure to CNPF in the laboratory. Low concentrations (between 0.0003 to 0.003 ppm) of toluene di-isocyanate were found in the air around this fabric. 4 of 9 women with symptoms had IgE antibodies to toluene di-isocyanate.

Risk assessment for consumer exposure to toluene diisocyanate (TDI) derived from polyurethane flexible foam.

PubMed

Arnold, Scott M; Collins, Michael A; Graham, Cynthia; Jolly, Athena T; Parod, Ralph J; Poole, Alan; Schupp, Thomas; Shiotsuka, Ronald N; Woolhiser, Michael R

2012-12-01

Polyurethanes (PU) are polymers made from diisocyanates and polyols for a variety of consumer products. It has been suggested that PU foam may contain trace amounts of residual toluene diisocyanate (TDI) monomers and present a health risk. To address this concern, the exposure scenario and health risks posed by sleeping on a PU foam mattress were evaluated. Toxicity benchmarks for key non-cancer endpoints (i.e., irritation, sensitization, respiratory tract effects) were determined by dividing points of departure by uncertainty factors. The cancer benchmark was derived using the USEPA Benchmark Dose Software. Results of previous migration and emission data of TDI from PU foam were combined with conservative exposure factors to calculate upper-bound dermal and inhalation exposures to TDI as well as a lifetime average daily dose to TDI from dermal exposure. For each non-cancer endpoint, the toxicity benchmark was divided by the calculated exposure to determine the margin of safety (MOS), which ranged from 200 (respiratory tract) to 3×10(6) (irritation). Although available data indicate TDI is not carcinogenic, a theoretical excess cancer risk (1×10(-7)) was calculated. We conclude from this assessment that sleeping on a PU foam mattress does not pose TDI-related health risks to consumers. Copyright © 2012 Elsevier Inc. All rights reserved.

Highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Stump, E. C., Jr.; Rochow, S. E. (Inventor)

1973-01-01

The reaction perfluorinated hydroxyl terminated polyether with diisocyanate to form polyurethane is discussed. Data are given on the resin's oxidation stability, chemical resistance, and low temperature flexibility.

Genome-Wide Association Study Identifies Novel Loci Associated With Diisocyanate-Induced Occupational Asthma

PubMed Central

Yucesoy, Berran; Kaufman, Kenneth M.; Lummus, Zana L.; Weirauch, Matthew T.; Zhang, Ge; Cartier, André; Boulet, Louis-Philippe; Sastre, Joaquin; Quirce, Santiago; Tarlo, Susan M.; Cruz, Maria-Jesus; Munoz, Xavier; Harley, John B.; Bernstein, David I.

2015-01-01

Diisocyanates, reactive chemicals used to produce polyurethane products, are the most common causes of occupational asthma. The aim of this study is to identify susceptibility gene variants that could contribute to the pathogenesis of diisocyanate asthma (DA) using a Genome-Wide Association Study (GWAS) approach. Genome-wide single nucleotide polymorphism (SNP) genotyping was performed in 74 diisocyanate-exposed workers with DA and 824 healthy controls using Omni-2.5 and Omni-5 SNP microarrays. We identified 11 SNPs that exceeded genome-wide significance; the strongest association was for the rs12913832 SNP located on chromosome 15, which has been mapped to the HERC2 gene (p = 6.94 × 10−14). Strong associations were also found for SNPs near the ODZ3 and CDH17 genes on chromosomes 4 and 8 (rs908084, p = 8.59 × 10−9 and rs2514805, p = 1.22 × 10−8, respectively). We also prioritized 38 SNPs with suggestive genome-wide significance (p < 1 × 10−6). Among them, 17 SNPs map to the PITPNC1, ACMSD, ZBTB16, ODZ3, and CDH17 gene loci. Functional genomics data indicate that 2 of the suggestive SNPs (rs2446823 and rs2446824) are located within putative binding sites for the CCAAT/Enhancer Binding Protein (CEBP) and Hepatocyte Nuclear Factor 4, Alpha transcription factors (TFs), respectively. This study identified SNPs mapping to the HERC2, CDH17, and ODZ3 genes as potential susceptibility loci for DA. Pathway analysis indicated that these genes are associated with antigen processing and presentation, and other immune pathways. Overlap of 2 suggestive SNPs with likely TF binding sites suggests possible roles in disruption of gene regulation. These results provide new insights into the genetic architecture of DA and serve as a basis for future functional and mechanistic studies. PMID:25918132

A novel kind of concrete superplasticizer based on aryl isocyanate polycondensates

NASA Astrophysics Data System (ADS)

Ding, Bei; Qian, Shanshan; Qiu, Ying; Wang, Yi; Zheng, Chunyang; Wang, Gaoming

2017-03-01

A novel superplasticizer was synthesized by polycondensation of Alkyl phenol phosphate and toluene diisocyanate grafting with methoxy polyoxyethylene ether (MPEG). The chemical structure and molecular weight of polycondensates molecules were determined by 1H nuclear magnetic resonance (NMR) and gel permeation chromatography respectively. The experimental results indicated that the polycondensates of Alkyl phenol phosphate and toluene diisocyanate grafting with MPEG not only exhibited good water-reducing properties but also demonstrated effective anti-clay abilities alone. Furthermore, the polycondensates showed good fluidity maintaining abilities within 1-3 h and good workability of concrete. The results of T500 Time experiments show that lower plastic viscosity of the polycondensates leads to fresh concrete much “looser” than conventional PCEs in self-compacting concrete.

Dimethylacetamide, ethylenediamine, and diphenylmethane diisocyanate poisoning manifest as acute psychosis and pulmonary edema: treatment with hemoperfusion.

PubMed

Su, T C; Lin, P H; Chiu, M J; Chu, T S; Chang, M J; Wang, J D; Cheng, T J

2000-01-01

A 27-year-old man, employed by a synthetic fiber company, had been exposed to dimethylacetamide, ethylenediamine, and diphenylmethane diisocyanate in a confined space continuously for 4-6 hours per day for 3 days before admission. Hallucinations and delusions were noted at admission; pulmonary edema developed subsequently. The electroencephalogram showed diffuse moderate cortical dysfunction and slow waves at 4-7 Hz, 20-80 microV. Seizures, liver injury, and rhabdomyolysis were noted on the 4th hospital day. The patient was treated by hemoperfusion with a decrease in urine dimethylacetamide from 3,265 mg/g to 4 mg/g creatinine over 4 days. Serial urinary dimethylacetamide and electroencephalogram correlated with the clinical condition.

Fact Sheet: Toluene Diisocyanate (TDI) and Related Compounds

EPA Pesticide Factsheets

EPA's existing chemicals programs address pollution prevention, risk assessment, hazard and exposure assessment and/or characterization, and risk management for chemicals substances in commercial use.

Untapped potential of health impact assessment.

PubMed

Winkler, Mirko S; Krieger, Gary R; Divall, Mark J; Cissé, Guéladio; Wielga, Mark; Singer, Burton H; Tanner, Marcel; Utzinger, Jürg

2013-04-01

The World Health Organization has promoted health impact assessment (HIA) for over 20 years. At the 2012 United Nations Conference on Sustainable Development (Rio+20), HIA was discussed as a critical method for linking health to "green economy" and "institutional framework" strategies for sustainable development. In countries having a high human development index (HDI), HIA has been added to the overall assessment suite that typically includes potential environmental and social impacts, but it is rarely required as part of the environmental and social impact assessment for large development projects. When they are performed, project-driven HIAs are governed by a combination of project proponent and multilateral lender performance standards rather than host country requirements. Not surprisingly, in low-HDI countries HIA is missing from the programme and policy arena in the absence of an external project driver. Major drivers of global change (e.g. population growth and urbanization, growing pressure on natural resources and climate change) inordinately affect low- and medium-HDI countries; however, in such countries HIA is conspicuously absent. If the cloak of HIA invisibility is to be removed, it must be shown that HIA is useful and beneficial and, hence, an essential component of the 21st century's sustainable development agenda. We analyse where and how HIA can become fully integrated into the impact assessment suite and argue that the impact of HIA must not remain obscure.

Untapped potential of health impact assessment

PubMed Central

Krieger, Gary R; Divall, Mark J; Cissé, Guéladio; Wielga, Mark; Singer, Burton H; Tanner, Marcel; Utzinger, Jürg

2013-01-01

Abstract The World Health Organization has promoted health impact assessment (HIA) for over 20 years. At the 2012 United Nations Conference on Sustainable Development (Rio+20), HIA was discussed as a critical method for linking health to “green economy” and “institutional framework” strategies for sustainable development. In countries having a high human development index (HDI), HIA has been added to the overall assessment suite that typically includes potential environmental and social impacts, but it is rarely required as part of the environmental and social impact assessment for large development projects. When they are performed, project-driven HIAs are governed by a combination of project proponent and multilateral lender performance standards rather than host country requirements. Not surprisingly, in low-HDI countries HIA is missing from the programme and policy arena in the absence of an external project driver. Major drivers of global change (e.g. population growth and urbanization, growing pressure on natural resources and climate change) inordinately affect low- and medium-HDI countries; however, in such countries HIA is conspicuously absent. If the cloak of HIA invisibility is to be removed, it must be shown that HIA is useful and beneficial and, hence, an essential component of the 21st century’s sustainable development agenda. We analyse where and how HIA can become fully integrated into the impact assessment suite and argue that the impact of HIA must not remain obscure. PMID:23599554

Socioeconomic disadvantage and schizophrenia in migrants under mental health detention orders.

PubMed

Bulla, Jan; Hoffmann, Klaus; Querengässer, Jan; Ross, Thomas

2017-09-01

Migrants with mental hospital orders according to section 63 of the German criminal code are overrepresented in relation to their numbers in the general population. Subgroups originating from certain world regions are diagnosed with schizophrenia at a much higher rate than others. In the present literature, there is a strong evidence for a substantial correlation between migration, social disadvantage and the prevalence of schizophrenia. This study investigates the relationship between countries of origin, the risk of becoming a forensic patient and the proportion of schizophrenia spectrum disorders. Data from a comprehensive evaluation tool of forensic inpatients in the German federal state of Baden-Württemberg (FoDoBa) were compared with population statistics and correlated with the Human Development Index (HDI) and Multidimensional Poverty Index (MPI). For residents with migration background, the risk ratio to receive a mental hospital order is 1.3 in comparison to non-migrants. There was a highly significant correlation between the HDI of the country of origin and the risk ratio for detention in a forensic psychiatric hospital. The proportion of schizophrenia diagnoses also correlated significantly with the HDI. In contrast, the MPI country rankings were not associated with schizophrenia diagnoses. Two lines of explanations are discussed: first, higher prevalence of schizophrenia in migrants originating from low-income countries, and second, a specific bias in court rulings with regard to involuntary forensic treatment orders for these migrant groups.

Spatio-Temporal Variation of Longevity Clusters and the Influence of Social Development Level on Lifespan in a Chinese Longevous Area (1982–2010)

PubMed Central

Qin, Jian; Xia, Tianlong; Li, You; Liang, Xue; Wei, Peng; Long, Bingshuang; Lei, Mingzhi; Wei, Xiao; Tang, Xianyan; Zhang, Zhiyong

2017-01-01

The study aims to determine the spatial and temporal variation of a longevous region and explore the correlation between longevity and socioeconomic development. Population data at the township level were obtained from the last four population censuses (1982–2010). Five main lifespan indicators and the Human Development Index (HDI) were calculated. Getis-Ord G*, Gravity modeling, and Pearson’s r between lifespan indicators and HDI were applied. In this study, a stable longevous gathering area was discovered in Hechi during different periods. Under the influence of social and economic development, more longevous areas appeared. However, the effects of genetic and natural environmental factors on longevity were always dominant in this remote and mountainous city. Furthermore, longevity indicators lacked any significant correlation with life expectancy. No significant positive correlation was detected between lifespan indicators and HDI. Thus, we conclude that lifespan indicators can determine the spatial distribution and variation pattern of longevity from multiple dimensions. The geographical scope of longevity in Hechi City is gradually expanding, and significant spatial clustering was detected in southwestern, southern, and eastern parts of Hechi. This study also found that social economic development is likely to have a certain impact on new longevous areas, but their role on extreme longevity is not significant. PMID:28753971

Prediction of Chemical Respiratory and Contact Sensitizers by OX40L Expression in Dendritic Cells Using a Novel 3D Coculture System.

PubMed

Mizoguchi, Izuru; Ohashi, Mio; Chiba, Yukino; Hasegawa, Hideaki; Xu, Mingli; Owaki, Toshiyuki; Yoshimoto, Takayuki

2017-01-01

The use of animal models in chemical safety testing will be significantly limited due to the recent introduction of the 3Rs principle of animal experimentation in research. Although several in vitro assays to predict the sensitizing potential of chemicals have been developed, these methods cannot distinguish chemical respiratory sensitizers and skin sensitizers. In the present study, we describe a novel in vitro assay that can discriminate respiratory sensitizers from chemical skin sensitizers by taking advantage of the fundamental difference between their modes of action, namely the development of the T helper 2 immune response, which is critically important for respiratory sensitization. First, we established a novel three-dimensional (3D) coculture system of human upper airway epithelium using a commercially available scaffold. It consists of human airway epithelial cell line BEAS-2B, immature dendritic cells (DCs) derived from human peripheral blood CD14 + monocytes, and human lung fibroblast cell line MRC-5. Respective cells were first cultured in individual scaffolds and subsequently assembled into a 3D multi-cell tissue model to more closely mimic the in vivo situation. Then, three typical chemicals that are known respiratory sensitizers (ortho-phthaldialdehyde, hexamethylene diisocyanate, and trimellitic anhydride) and skin sensitizers (oxazolone, formaldehyde, and dinitrochlorobenzene) were added individually to the 3D coculture system. Immunohistochemical analysis revealed that DCs do not migrate into other scaffolds under the experimental conditions. Therefore, the 3D structure was disassembled and real-time reverse transcriptase-PCR analysis was performed in individual scaffolds to analyze the expression levels of molecules critical for Th2 differentiation such as OX40 ligand (OX40L), interleukin (IL)-4, IL-10, IL-33, and thymic stromal lymphopoietin. Both sensitizers showed similarly augmented expression of DC maturation markers (e.g., CD86), but among these molecules, OX40L expression in DCs was most consistently and significantly enhanced by respiratory sensitizers as compared to that by skin sensitizers. Thus, we have established a 3D coculture system mimicking the airway upper epithelium that may be successfully applied to discriminate chemical respiratory sensitizers from skin sensitizers by measuring the critical molecule for Th2 differentiation, OX40L, in DCs.

Nerve regeneration using tubular scaffolds from biodegradable polyurethane.

PubMed

Hausner, T; Schmidhammer, R; Zandieh, S; Hopf, R; Schultz, A; Gogolewski, S; Hertz, H; Redl, H

2007-01-01

In severe nerve lesion, nerve defects and in brachial plexus reconstruction, autologous nerve grafting is the golden standard. Although, nerve grafting technique is the best available approach a major disadvantages exists: there is a limited source of autologous nerve grafts. This study presents data on the use of tubular scaffolds with uniaxial pore orientation from experimental biodegradable polyurethanes coated with fibrin sealant to regenerate a 8 mm resected segment of rat sciatic nerve. Tubular scaffolds: prepared by extrusion of the polymer solution in DMF into water coagulation bath. The polymer used for the preparation of tubular scaffolds was a biodegradable polyurethane based on hexamethylene diisocyanate, poly(epsilon-caprolactone) and dianhydro-D-sorbitol. EXPERIMENTAL MODEL: Eighteen Sprague Dawley rats underwent mid-thigh sciatic nerve transection and were randomly assigned to two experimental groups with immediate repair: (1) tubular scaffold, (2) 180 degrees rotated sciatic nerve segment (control). Serial functional measurements (toe spread test, placing tests) were performed weekly from 3rd to 12th week after nerve repair. On week 12, electrophysiological assessment was performed. Sciatic nerve and scaffold/nerve grafts were harvested for histomorphometric analysis. Collagenic connective tissue, Schwann cells and axons were evaluated in the proximal nerve stump, the scaffold/nerve graft and the distal nerve stump. The implants have uniaxially-oriented pore structure with a pore size in the range of 2 micorm (the pore wall) and 75 x 700 microm (elongated pores in the implant lumen). The skin of the tubular implants was nonporous. Animals which underwent repair with tubular scaffolds of biodegradable polyurethanes coated with diluted fibrin sealant had no significant functional differences compared with the nerve graft group. Control group resulted in a trend-wise better electrophysiological recovery but did not show statistically significant differences. There was a higher level of collagenic connective tissue within the scaffold and within the distal nerve stump. Schwann cells migrated into the polyurethane scaffold. There was no statistical difference to the nerve graft group although Schwann cell counts were lower especially within the middle of the polyurethane scaffold. Axon counts showed a trend-wise decrease within the scaffold. These results suggest that biodegradable polyurethane tubular scaffolds coated with diluted fibrin sealant support peripheral nerve regeneration in a standard gap model in the rat up to 3 months. Three months after surgery no sign of degradation could be seen.

Biodegradable hyperbranched amphiphilic polyurethane multiblock copolymers consisting of poly(propylene glycol), poly(ethylene glycol), and polycaprolactone as in situ thermogels.

PubMed

Li, Zibiao; Zhang, Zhongxing; Liu, Kerh Li; Ni, Xiping; Li, Jun

2012-12-10

This paper reports the synthesis and characterization of new hyperbranched amphiphilic polyurethane multiblock copolymers consisting of poly(propylene glycol) (PPG), poly(ethylene glycol) (PEG), and polycaprolactone (PCL) segments as in situ thermogels. The hyperbranched poly(PPG/PEG/PCL urethane)s, termed as HBPEC copolymers, were synthesized from PPG-diol, PEG-diol, and PCL-triol by using 1,6-hexamethylene diisocyanate (HMDI) as a coupling agent. The compositions and structures of HBPEC copolymers were determined by GPC and 1H NMR spectroscopy. We carried out comparative studies of the new hyperbranched copolymers with their linear counterparts, the linear poly(PPG/PEG/PCL urethane) (LPEC) copolymer and Pluronic F127 PEG-PPG-PEG block copolymer, in terms of their self-assembly and aggregation behaviors and thermoresponsive properties. HBPEC copolymers were found to show thermoresponsive micelle formation and aggregation behaviors. Particularly, the lower critical solution temperature (LCST) of the copolymers was significantly affected by the copolymer architecture. HBPEC copolymers showed much lower LCST than LPEC, the linear counterpart. Our studies revealed that the effect of hyperbranch architecture was more prominent in the gelation of the copolymers. The aqueous solutions of HBPEC copolymers exhibited thermogelling behaviors at critical gelation concentrations (CGCs) ranging from 4.3 to 7.4 wt %. These values are much lower than those reported on other PCL-contained linear thermogelling copolymers and Pluronic F127 copolymer. In addition, the CGC of HBPEC copolymers is much lower than the control LPEC copolymer. More interestingly, at high temperatures, while LPEC and other linear thermogelling copolymers formed turbid sol, HBPEC formed a dehydrated gel. Our data suggest that these phenomena are caused by the hyperbranched structure of HBPEC copolymers, which could increase the interaction of copolymer branches and enhance the chain association through synergetic hydrogen bonding effect. The thermogelling behavior of HBPEC block copolymers was further evidenced by the 1H NMR molecular dynamic study and rheological study, which further support the above hypothesis. The hydrolytic degradation study showed that the HBPEC copolymer hydrogels are biodegradable under physiological conditions. Together with the good cell biocompatibility demonstrated by the cytotoxicity study, the new thermogelling copolymers reported in this paper could potentially be used as in situ-forming hydrogels for biomedical applications.

Disruptive Technologies in Workmanship: pH-neutral Flux, CDM ESD Events, HDI PCBs

NASA Technical Reports Server (NTRS)

Plante, Jeannette F.

2010-01-01

This slide presentation describes what it calls "disruptive technologies", i.e., "Low-end disruption" occurs when the rate at which products improve exceeds the rate at which customers can adopt the new performance. Therefore, at some point the performance of the product overshoots the needs of certain customer segments. At this point, a disruptive technology may enter the market and provide a product which has lower performance than the incumbent but which exceeds the requirements of certain segments, thereby gaining a foothold in the market. This concept is viewed in impacting incumbent technologies Rosin Flux, with a pH-neutral water soluble Flux; electrostatic discharge models being disrupted by the charge device model (CDM) concept; and High Density Interconnect Printed Circuit Boards (HDI PCB).

Heat sterilizable solid-propellant development

NASA Technical Reports Server (NTRS)

Kalfayan, S. H.

1981-01-01

The binders tested were polyurethanes made from two hydroxy-terminated polybutadienes, R-45 and Butarez HT, one hydroxy-terminated butadiene-acrylonitrile copolymer, Hycar 1300X 17, and a hydroxy-terminated prepolymer, Esterdiol 560, made from the dimerized fatty acid Empol 1010. The isocyanates used most extensively were isophorone diisocyanate (IPDI) and a polymeric diisocyanate, DDI. Stress relaxation was used to examine the chemical changes that took place in the binder when subjected to the sterilization temperatures. The thermal stability of the oxidizer, ammonium perchlorate (AP), was tested by thermogravimetry in the isothermal and nonisothermal modes. The effect of particle size, recrystallization, moisture content, and doping on the heat stability of AP could be evaluated by this method. The volatile degradation products, obtained when AP samples were aged at 135 C for prolonged periods, were analyzed by mass spectroscopy.

Synthesis and molecular characterization of chitosan based polyurethane elastomers using aromatic diisocyanate.

PubMed

Zia, Khalid Mahmood; Anjum, Sohail; Zuber, Mohammad; Mujahid, Muhammad; Jamil, Tahir

2014-05-01

The present research work was performed to synthesize a new series of chitosan based polyurethane elastomers (PUEs) using poly(ɛ-caprolactone) (PCL). The chitosan based PUEs were prepared by step-growth polymerization technique using poly(ɛ-caprolactone) (PCL) and 2,4-toluene diisocyanate (TDI). In the second step the PU prepolymer was extended with different mole ratios of chitosan and 1,4-butane diol (BDO). Molecular engineering was carried out during the synthesis. The conventional spectroscopic characterization of the synthesized samples using FT-IR confirms the existence of the proposed chitosan based PUEs structure. Internal morphology of the prepared PUEs was studied using SEM analysis. The SEM images confirmed the incorporation of chitosan molecules into the PU backbone. Copyright © 2014 Elsevier B.V. All rights reserved.

Asthma and Hispanic Americans

MedlinePlus

... as bronchitis. Children living below or near the poverty level are more likely to have high levels ... www.cdc.gov/nchs/hdi.htm The proportional impact of asthma prevalence, health care use and mortality ...

Building the evidence base for global tobacco control.

PubMed Central

Corrao, M. A.; Guindon, G. E.; Cokkinides, V.; Sharma, N.

2000-01-01

The tobacco control movement needs a global information system permitting routine monitoring of the tobacco trade, tobacco farming, the tobacco industry, the prevalence of tobacco use, associated mortality, and national resources for combating tobacco. The Tobacco Control Country Profiles database, a data collection initiative led by the American Cancer Society in collaboration with WHO and the Centers for Disease Control and Prevention, represents the first step in the development of such a system. Baseline data on several indicators of tobacco use were obtained from 191 Member States of WHO, two Associate Members, Hong Kong Special Administrative Region of China (Hong Kong SAR), China (Province of Taiwan) and the West Bank and Gaza Strip. The methods used to compile the data are described in the present paper. Selected indicators from the database were analysed in order to demonstrate the potential utility and value of data derived from an information system devoted to tobacco control. The analyses covered gender-specific smoking prevalence by WHO Region, per capita cigarette consumption by Human Development Index (HDI) category, and average real annual percentage changes in cigarette prices between 1990 and 1999 for selected countries in each category. In 1998, men were almost four times more likely than women to be smokers. The prevalence of smoking among men was highest in the Western Pacific Region. The differential in gender-specific smoking prevalence was narrowest in the Region of the Americas and the European Region. It was wider in the South-East Asia Region and the Western Pacific Region. The lowest and highest per capita consumption of manufactured cigarettes occurred in the lowest and highest HDI categories respectively. In the medium HDI category, China's growing cigarette consumption after 1975 had a major bearing on the rise in per capita consumption. Cigarette price trends suggest that there is considerable scope for increasing taxes on tobacco products, particularly in low or medium HDI countries. The implications of the findings for future tobacco control efforts are discussed, as are issues surrounding the quality of available data, priorities for future data collection and the need to maintain and improve the information system in order to support such efforts. PMID:10994261

Effect of manual therapy techniques on headache disability in patients with tension-type headache. Randomized controlled trial.

PubMed

Espí-López, G V; Rodríguez-Blanco, C; Oliva-Pascual-Vaca, A; Benítez-Martínez, J C; Lluch, E; Falla, D

2014-12-01

Tension-type headache (TTH) is the most common type of primary headache however there is no clear evidence as to which specific treatment is most effective or whether combined treatment is more effective than individual treatments. To assess the effectiveness of manual therapy techniques, applied to the suboccipital region, on aspects of disability in a sample of patients with tension-type headache. Randomized Controlled Trial. Specialized centre for headache treatment. Seventy-six (62 women) patients (age: 39.9 ± 10.9 years) with episodic chronic TTH. Patients were randomly divided into four treatment groups: 1) suboccipital soft tissue inhibition; 2) occiput-atlas-axis manipulation; 3) combined treatment of both techniques; 4) control. Four sessions were applied over 4 weeks and disability was assessed before and after treatment using the Headache Disability Inventory (HDI). Headache frequency, severity and the functional and emotional subscales of the questionnaire were assessed. Photophobia, phonophobia and pericranial tenderness were also monitored. Headache frequency was significantly reduced with the manipulative and combined treatment (P<0.05), and the severity and functional subscale of the HDI changed in all three treatment groups (P<0.05). Manipulation treatment also reduced the score on the emotional subscale of the HDI (P<0.05). The combined intervention showed a greater effect at reducing the overall HDI score compared to the group that received suboccipital soft tissue inhibition and to the control group (both P<0.05). In addition, photophobia, phonophobia and pericranial tenderness only improved in the group receiving combined therapy (P<0.05). When given individually, suboccipital soft tissue inhibition and occiput-atlas-axis manipulation resulted in changes in different parameters related to the disability caused by TTH. However, when the two treatments were combined, effectiveness was noted for all aspects of disability and other symptoms including photophobia, phonophobia and pericranial tenderness. Although individual manual therapy treatments showed a positive change in headache features, measures of photophobia, photophobia and pericranial tenderness only improved in the group that received the combined treatment suggesting that combined treatment is the most appropriate for symptomatic relief of TTH.

What do we know about the needs and challenges of health systems? A scoping review of the international literature.

PubMed

Roncarolo, Federico; Boivin, Antoine; Denis, Jean-Louis; Hébert, Rejean; Lehoux, Pascale

2017-09-08

While there is an extensive literature on Health System (HS) strengthening and on the performance of specific HSs, there are few exhaustive syntheses of the challenges HSs are facing worldwide. This paper reports the findings of a scoping review aiming to classify the challenges of HSs investigated in the scientific literature. Specifically, it determines the kind of research conducted on HS challenges, where it was performed, in which health sectors and on which populations. It also identifies the types of challenge described the most and how they varied across countries. We searched 8 databases to identify scientific papers published in English, French and Italian between January 2000 and April 2016 that addressed HS needs and challenges. The challenges reported in the articles were classified using van Olmen et al.'s dynamic HS framework. Countries were classified using the Human Development Index (HDI). Our analyses relied on descriptive statistics and qualitative content analysis. 292 articles were included in our scoping review. 33.6% of these articles were empirical studies and 60.1% were specific to countries falling within the very high HDI category, in particular the United States. The most frequently researched sectors were mental health (41%), infectious diseases (12%) and primary care (11%). The most frequently studied target populations included elderly people (23%), people living in remote or poor areas (21%), visible or ethnic minorities (15%), and children and adolescents (15%). The most frequently reported challenges related to human resources (22%), leadership and governance (21%) and health service delivery (24%). While health service delivery challenges were more often examined in countries within the very high HDI category, human resources challenges attracted more attention within the low HDI category. This scoping review provides a quantitative description of the available evidence on HS challenges and a qualitative exploration of the dynamic relationships that HS components entertain. While health services research is increasingly concerned about the way HSs can adopt innovations, little is known about the system-level challenges that innovations should address in the first place. Within this perspective, four key lessons are drawn as well as three knowledge gaps.

The Incidence and Mortality of Colorectal Cancer and Its Relationship With the Human Development Index in Asia.

PubMed

Ghoncheh, Mahshid; Mohammadian, Maryam; Mohammadian-Hafshejani, Abdollah; Salehiniya, Hamid

Colorectal cancer is the second most common cancer in women and the third most common cancer among men, and its incidence is increasing in Asia. Awareness about the status of this cancer incidence and mortality is necessary for a better plan. The present study was done with the aim to investigate the incidence and mortality of colorectal cancer and its relationship with the Human Development Index (HDI) in Asia in 2012. This study was an ecological study, which was conducted based on the GLOBOCAN project of the World Health Organization for Asian countries. We assessed the correlation between standardized incidence rates (SIR) and standardized mortality rates (SMR) of colorectal cancer with HDI and its components using SPSS software, version 18 (SPSS Inc., Chicago, IL). A total of 592,563 incidences of and 325,752 deaths from colorectal cancer were recorded in Asian countries in 2012. The 5 countries with the highest SIR were Republic of Korea (45 per 100,000), Israel (35.9 per 100,000), Singapore (33.7 per 100,000), Japan (32.2 per 100,000), and Jordan (25.6 per 100,000). The 5 countries with the highest SMR for colorectal cancer were Jordan (15.5 per 100,000), Kazakhstan (12.8 per 100,000), Democratic Republic of Korea (12 per 100,000), Brunei (12 per 100,000), and Japan (11.9 per 100,000). Correlation between HDI and SIR was 0.709 overall (P ≤ .001)- 0.667 in men (P ≤ .001) and 0.759 in women (P ≤ .001). Also, correlation between HDI and SMR overall was 0.517 (P ≤ .001)- 0.447 in men (P = .002) and 0.593 in women (P ≤ .001). Cancer incidence and mortality are higher in countries with more development. A positive and statistically significant correlation was found between standardized incidence and mortality rate of colorectal cancer and the Human Development Index and its components. Copyright © 2016. Published by Elsevier Inc.

Toluene diisocyanate: Induction of the autotaxin-lysophosphatidic acid axis and its association with airways symptoms

DOE Office of Scientific and Technical Information (OSTI.GOV)

Broström, Julia M.; Ye, Zhi-wei; Axmon, Anna

Diisocyanates are industrial chemicals which have a wide range of applications in developed and developing countries. They are notorious lung toxicants and respiratory sensitizers. However, the mechanisms behind their adverse effects are not adequately characterized. Autotaxin (ATX) is an enzyme producing lysophosphatidic acid (LPA), and the ATX-LPA axis has been implicated in lung related inflammatory conditions and diseases, including allergic asthma, but not to toxicity of environmental low-molecular-weight chemicals. We investigated effects of toluene diisocyanate (TDI) on ATX induction in human lung epithelial cell models, and we correlated LPA-levels in plasma to biomarkers of TDI exposure in urine collected frommore » workers exposed to < 5 ppb (parts per billion). Information on workers' symptoms was collected through interviews. One nanomolar TDI robustly induced ATX release within 10 min in vitro. A P2X7- and P2X4-dependent microvesicle formation was implicated in a rapid ATX release and a subsequent protein synthesis. Co-localization between purinergic receptors and ATX was documented by immunofluorescence and confocal microscopy. The release was modulated by monocyte chemoattractant protein-1 (MCP-1) and by extracellular ATP. In workers, we found a dose–response relationship between TDI exposure biomarkers in urine and LPA levels in plasma. Among symptomatic workers reporting “sneezing”, the LPA levels were higher than among non-symptomatic workers. This is the first report indicating induction of the ATX-LPA axis by an environmental low-molecular-weight chemical, and our data suggest a role for the ATX-LPA axis in TDI toxicity. - Highlights: • Human epithelial cells release autotaxin in response to 1 nM toluene diisocyanate (TDI). • The release involves P2X4 and P2X7 receptors and is modulated by ATP and MCP-1. • Lysophosphatidic acid (LPA) was measured in workers exposed to < 5 ppb TDI. • LPA in plasma correlated to TDI exposure biomarkers in workers. • Symptomatic workers had higher LPA levels than those without symptoms.« less

International Comparison of Water Resources Utilization Efficiency in the Silk Road Economic Belt

NASA Astrophysics Data System (ADS)

Yan, Long; Ma, Jing; Deng, Wei; Wang, Yong

2018-03-01

In order to get knowledge of the standard of water utilization of the Silk Road Economic Belt from international point of view, the paper analyzes the annual variation of water resources utilization in the Silk Road Economic Belt, and compares with other typical countries. The study shows that Water resources utilization efficiency has been greatly improved in recent 20 years and the water consumption per USD 10000 of GDP has been declined 87.97%. the improvement of industrial water consumption efficiency is the key driving factors for substantial decrease in water consumption.The comparison of water utilization and human development shows that the higher HDI the country is, the more efficient water utilization the country has. water consumption per USD 10000 of GDP in country with HDI>0.9 is 194m³, being 8.5% of that in country with HDI from 0.5 to 0.6. On the premise of maintaining the stable economic and social development of the Silk Road Economic Belt, the realization of the control target of total water consumption must depend on the strict control over the disorderly expansion of irrigated area, the change in the mode of economic growth, the implementation of the development strategy for new industrialization and urbanization, vigorous development of the processing industry with low water consumption as well as the high-tech and high value-added industry. Only in this way, the control target of total water consumption can be realized in the process of completing the industrialization task.

Alcohol-Related Negative Consequences among Drinkers around the World

PubMed Central

Graham, Kathryn; Bernards, Sharon; Knibbe, Ronald; Kairouz, Sylvia; Kuntche, Sandra; Wilsnack, Sharon C.; Greenfield, Thomas K.; Dietze, Paul; Obot, Isidore; Gmel, Gerhard

2013-01-01

Aims This paper examines (1) gender and country differences in negative consequences related to drinking; (2) relative rates of different consequences; (3) country-level predictors of consequences. Design, setting and participants Multi-level analyses used survey data from the GENACIS collaboration. Measurements Measures included 17 negative consequences grouped into (a) high endorsement acute, (b) personal and (c) social. Country-level measures included average frequency and quantity of drinking, percent current drinkers, Gross Domestic Product (GDP) and Human Development Index (HDI). Findings Overall, the three groupings of consequences were reported by 44%, 12% and 7% of men and by 31%, 6% and 3% of women, respectively. More men than women endorsed all consequences but gender differences were greatest for consequences associated with chronic drinking and social consequences related to male roles. The highest prevalence of consequences was in Uganda, lowest in Uruguay. Personal and social consequences were more likely in countries with higher usual quantity, fewer current drinkers, and lower scores on GDP and HDI. However, significant interactions with individual-level quantity indicated a stronger relationship between consequences and usual quantity among drinkers in countries with lower quantity, more current drinkers and higher scores on GDP and HDI. Conclusions Both gender and country need to be taken into consideration when assessing adverse drinking consequences. Individual measures of alcohol consumption and country-level variables are associated with experiencing such consequences. Additionally, country-level variables affect the strength of the relationship between usual quantity consumed by individuals and adverse consequences. PMID:21395893

Suicide rate in relation to the Human Development Index and other health related factors: A global ecological study from 91 countries.

PubMed

Khazaei, Salman; Armanmehr, Vajihe; Nematollahi, Shahrzad; Rezaeian, Shahab; Khazaei, Somayeh

2017-06-01

There has been no worldwide ecological study on suicide as a global major public health problem. This study aimed to identify the variations in suicide specific rates using the Human Development Index (HDI) and some health related variables among countries around the world. In this ecological study, we obtained the data from the World Bank Report 2013. The analysis was restricted to 91 countries for which both the epidemiologic data from the suicide rates and HDI were available. Overall, the global prevalence of suicide rate was 10.5 (95% confidence intervals: 8.8, 12.2) per 100,000 individuals, which significantly varied according to gender (16.3 in males vs. 4.6 in females, p<0.001) and different levels of human development (11.64/100,000 individuals in very high development countries, 7.93/100,000 individuals in medium development countries, and 13.94/100,000 individuals in high development countries, p=0.004). In conclusion, the suicide rate varies greatly between countries with different development levels. Our findings also suggest that male gender and HDI components are associated with an increased risk of suicide behaviors. Hence, detecting population subgroups with a high suicide risk and reducing the inequality of socioeconomic determinants are necessary to prevent this disorder around the world. Copyright © 2017 Ministry of Health, Saudi Arabia. Published by Elsevier Ltd. All rights reserved.

Educational inequalities in obesity, abdominal obesity, and metabolic syndrome in seven Latin American cities: the CARMELA Study.

PubMed

Boissonnet, Carlos; Schargrodsky, Herman; Pellegrini, Fabio; Macchia, Alejandro; Marcet Champagne, Beatriz; Wilson, Elinor; Tognoni, Gianni

2011-08-01

Earlier reviews have found that the proportion of inverse associations between socioeconomic status and obesity increased according to the level of development of the studied country. Based on this finding, it has been hypothesized that in low- to middle- income countries the burden of obesity shifts to disadvantaged groups as a country develops. CARMELA is a cross-sectional, population-based observational study that sampled 11,550 women and men age 25-64 from seven major Latin American cities. We analyzed by gender the association of educational attainments (as proxy of socioeconomic status) with body mass index, waist circumference and metabolic syndrome. Participating cities were divided by country Human Development Index (HDI). An inverse gradient between socioeconomic status and body mass index in women was uniformly present in High HDI cities (Buenos Aires, Santiago, Mexico) but not in Medium HDI group (Barquisimeto, Bogota, Lima, Quito), where two cities showed an inverse gradient and two cities did not. In men, no clear socioeconomic gradients were found. Findings regarding waist circumference and metabolic syndrome closely mirrored those about body mass index. In women but not men, these results give support to the hypothesis of obesity shifting to the poor and extend it to the related concepts of abdominal obesity and metabolic syndrome. Obesity should be considered as a socially-generated disease and an indicator of socioeconomic disadvantage, to be approached by comprehensive strategies that bear in mind this perspective.

Concept of an advanced hyperspectral remote sensing system for pipeline monitoring

NASA Astrophysics Data System (ADS)

Keskin, Göksu; Teutsch, Caroline D.; Lenz, Andreas; Middelmann, Wolfgang

2015-10-01

Areas occupied by oil pipelines and storage facilities are prone to severe contamination due to leaks caused by natural forces, poor maintenance or third parties. These threats have to be detected as quickly as possible in order to prevent serious environmental damage. Periodical and emergency monitoring activities need to be carried out for successful disaster management and pollution minimization. Airborne remote sensing stands out as an appropriate choice to operate either in an emergency or periodically. Hydrocarbon Index (HI) and Hydrocarbon Detection Index (HDI) utilize the unique absorption features of hydrocarbon based materials at SWIR spectral region. These band ratio based methods require no a priori knowledge of the reference spectrum and can be calculated in real time. This work introduces a flexible airborne pipeline monitoring system based on the online quasi-operational hyperspectral remote sensing system developed at Fraunhofer IOSB, utilizing HI and HDI for oil leak detection on the data acquired by an SWIR imaging sensor. Robustness of HI and HDI compared to state of the art detection algorithms is evaluated in an experimental setup using a synthetic dataset, which was prepared in a systematic way to simulate linear mixtures of selected background and oil spectra consisting of gradually decreasing percentages of oil content. Real airborne measurements in Ettlingen, Germany are used to gather background data while the crude oil spectrum was measured with a field spectrometer. The results indicate that the system can be utilized for online and offline monitoring activities.

Phylogenetic Affiliation of Soil Bacteria That Degrade Aliphatic Polyesters Available Commercially as Biodegradable Plastics

PubMed Central

Suyama, Tetsushi; Tokiwa, Yutaka; Ouichanpagdee, Pornpimol; Kanagawa, Takahiro; Kamagata, Yoichi

1998-01-01

Thirty-nine morphologically different soil bacteria capable of degrading poly(β-hydroxyalkanoate), poly(ɛ-caprolactone), poly(hexamethylene carbonate), or poly(tetramethylene succinate) were isolated. Their phylogenetic positions were determined by 16S ribosomal DNA sequencing, and all of them fell into the classes Firmicutes and Proteobacteria. Determinations of substrate utilization revealed characteristic patterns of substrate specificities. PMID:9835597

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2014 CFR

2014-04-01

... data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate.* Borax or boric acid for use in adhesives... paperboard which is waxed.* Hexamethylene tetramine as a setting agent for protein, including casein.* 1-(2... 21 Food and Drugs 3 2014-04-01 2014-04-01 false Substances used in the manufacture of paper and...

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2013 CFR

2013-04-01

..., based on available scientific information and data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate... 21 Food and Drugs 3 2013-04-01 2013-04-01 false Substances used in the manufacture of paper and... only on paper and paperboard which is waxed.* Hexamethylene tetramine as a setting agent for protein...

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2010 CFR

2010-04-01

..., based on available scientific information and data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Substances used in the manufacture of paper and... only on paper and paperboard which is waxed.* Hexamethylene tetramine as a setting agent for protein...

21 CFR 181.30 - Substances used in the manufacture of paper and paperboard products used in food packaging.

Code of Federal Regulations, 2012 CFR

2012-04-01

..., based on available scientific information and data. 1-Alkyl (C6-C18)3-amino-3-aminopropane monoacetate... 21 Food and Drugs 3 2012-04-01 2012-04-01 false Substances used in the manufacture of paper and... only on paper and paperboard which is waxed.* Hexamethylene tetramine as a setting agent for protein...

Presidential Green Chemistry Challenge: 2005 Greener Reaction Conditions Award

EPA Pesticide Factsheets

Presidential Green Chemistry Challenge 2005 award winner, BASF, invented a one-component, urethane acrylate oligomer primer system for automobile refinishing that is UV-curable, has VOCs, and is free of diisocyanates.

Antibodies against toluene diisocyanate protein conjugates. Three methods of measurement.

PubMed

Patterson, R; Harris, K E; Zeiss, C R

1983-12-01

With the use of canine antisera against toluene diisocyanate (TDI)-dog serum albumin (DSA), techniques for measuring antibody against TDI-DSA were evaluated. The use of an ammonium sulfate precipitation assay showed suggestive evidence of antibody binding but high levels of TDI-DSA precipitation in the absence of antibody limit any usefulness of this technique. Double-antibody co-precipitation techniques will measure total antibody or Ig class antibody against 125I-TDI-DSA. These techniques are quantitative. The polystyrene tube radioimmunoassay is a highly sensitive method of detecting and quantitatively estimating IgG antibody. The enzyme linked immunosorbent assay is a rapidly adaptable method for the quantitative estimation of IgG, IgA, and IgM against TDI-homologous proteins. All these techniques were compared and results are demonstrated by using the same serum sample for analysis.

Microwave-assisted synthesis of cyclodextrin polyurethanes.

PubMed

Biswas, Atanu; Appell, Michael; Liu, Zengshe; Cheng, H N

2015-11-20

Cyclodextrin (CD) has often been incorporated into polyurethanes in order to facilitate its use in encapsulation or removal of organic species for various applications. In this work a microwave-assisted method has been developed to produce polyurethanes consisting of α-, β-, and γ-CD and three common diisocyanates. As compared to conventional heating, this new synthetic method saves energy, significantly reduces reaction time, and gets similar or improved yield. The reaction products have been fully characterized with (13)C, (1)H, and two-dimensional NMR spectroscopy. With suitable stoichiometry of starting CD and diisocyanate, the resulting CD polyurethane is organic-soluble and water-insoluble and is shown to remove Nile red dye and phenol from water. Possible applications include the removal of undesirable materials from process streams, toxic compounds from the environment, and encapsulation of color or fragrance molecules. Published by Elsevier Ltd.

Using Gas Phase Reactions of Hexamethylene Triperoxide Diamine (HMTD) to Improve Detection in Mass Spectrometry

NASA Astrophysics Data System (ADS)

Colizza, Kevin; Yevdokimov, Alexander; McLennan, Lindsay; Smith, James L.; Oxley, Jimmie C.

2018-01-01

Our efforts to lower the detection limits of hexamethylene triperoxide diamine (HMTD) have uncovered previously unreported gas-phase reactions of primary and secondary amines with one of the six methylene carbons. The reaction occurs primarily in the atmospheric pressure chemical ionization (APCI) source and is similar to the behavior of alcohols with HMTD [1]. However, unlike alcohols, the amine reaction conserves the hydrogen peroxide on the intact product. Furthermore, with or without amines, HMTD is oxidized to tetramethylene diperoxide diamine dialdehyde (TMDDD) in a temperature-dependent fashion in the APCI source. Synthesized TMDDD forms very strong adducts (not products) to ammonium and amine ions in the electrospray ionization (ESI) source. Attempts to improve HMTD detection by generating TMDDD in the APCI source with post-column addition of amines were not successful. Signal intensity of the solvent related HMTD product in methanol, [HMTD+MeOH2-H2O2]+ (m/z 207.0975), was understandably related to the amount of methanol in the HMTD environment as it elutes into the source. With conditions optimized for this product, the detection of 100 pg on column was accomplished with a robust analysis of 300 pg (1.44 pmol) routinely performed on the Orbitrap mass spectrometers. [Figure not available: see fulltext.

Efficacy of HIV Prevention Interventions in Latin American and Caribbean Nations, 1995–2008: A Meta-Analysis

PubMed Central

Huedo-Medina, Tania B.; Boynton, Marcella H.; Warren, Michelle R.; LaCroix, Jessica M.; Carey, Michael P.; Johnson, Blair T.

2014-01-01

This meta-analysis synthesized 34 HIV prevention interventions (from 27 studies) that were evaluated in Latin American and Caribbean nations. These studies were obtained through systematic searches of English, Spanish, and Portuguese-language databases available as of January 2009. Overall, interventions significantly increased knowledge (d = 0.51) and condom use (d = 0.28) but the effects varied widely. Interventions produced more condom use when they focused on high-risk individuals, distributed condoms, and explicitly addressed socio-cultural components. The best-fitting models utilized factors related to geography, especially indices of a nations’ human development index (HDI) and income inequality (i.e., Gini index). Interventions that provided at least three hours of content succeeded better when HDI and income inequality were lower, suggesting that intensive HIV prevention activities succeed best where the need is greatest. Implications for HIV intervention development in Latin America and the Caribbean are discussed. PMID:20661768

Alcohol-related negative consequences among drinkers around the world.

PubMed

Graham, Kathryn; Bernards, Sharon; Knibbe, Ronald; Kairouz, Sylvia; Kuntsche, Sandra; Wilsnack, Sharon C; Greenfield, Thomas K; Dietze, Paul; Obot, Isidore; Gmel, Gerhard

2011-08-01

This paper examines (i) gender and country differences in negative consequences related to drinking; (ii) relative rates of different consequences; and (iii) country-level predictors of consequences. Multi-level analyses used survey data from the Gender, Alcohol, and Culture: An International Study (GENACIS) collaboration. Measures included 17 negative consequences grouped into (i) high endorsement acute, (ii) personal and (iii) social. Country-level measures included average frequency and quantity of drinking, percentage who were current drinkers, gross domestic product (GDP) and Human Development Index (HDI). Overall, the three groupings of consequences were reported by 44%, 12% and 7% of men and by 31%, 6% and 3% of women, respectively. More men than women endorsed all consequences, but gender differences were greatest for consequences associated with chronic drinking and social consequences related to male roles. The highest prevalence of consequences was in Uganda and lowest in Uruguay. Personal and social consequences were more likely in countries with higher usual quantity, fewer current drinkers and lower scores on GDP and HDI. However, significant interactions with individual-level quantity indicated a stronger relationship between consequences and usual quantity among drinkers in countries with lower quantity, more current drinkers and higher scores on GDP and HDI. Both gender and country need to be taken into consideration when assessing adverse drinking consequences. Individual measures of alcohol consumption and country-level variables are associated with experiencing such consequences. Additionally, country-level variables affect the strength of the relationship between usual quantity consumed by individuals and adverse consequences. © 2011 The Authors, Addiction © 2011 Society for the Study of Addiction.

The roles of contextual and individual social determinants of oral health-related quality of life in Brazilian adults.

PubMed

Vettore, Mario Vianna; Aqeeli, Amal

2016-04-01

This study investigated the relationship between contextual and individual social determinants of oral health-related quality of life (OHRQoL) in Brazilian adults. Data of 4594 Brazilian adults aged 35-44 years from the 2010 Brazilian Oral Health Survey were analysed. OHRQoL was measured using the Oral Impacts on Daily Performance (OIDP). Contextual socio-economic characteristics at city level assessed in 1991 and 2000 included social deprivation measured by Human Development Index (HDI) and income inequality (Gini index). Individual socio-economic characteristics included family income, schooling and number of goods. Covariates were age, sex, ethnicity and clinical oral measures. Multilevel multivariable Poisson regression analysis was carried to investigate the association of contextual and individual social characteristics with OIDP extent and with each OIDP item. Eating and cleaning teeth were the most reported daily activities influenced by oral conditions. In the adjusted analysis, low HDI 1991 and individual social characteristics (lower family income and lower schooling) were associated with OIDP extent. Sex (females) and all clinical oral measures were also associated with OIDP. Adults living in the cities with low HDI 1991 were more likely to have impact on eating and sleeping, whereas living in cities with high Gini index 1991 increased the prevalence of impact on emotional status, work and social contact. Low income was associated with all OIDP items. Poor contextual social determinants and lower individual socio-economic position are associated with worse OHRQoL among Brazilian adults, even after adjusting for individual socio-demographic and clinical oral health variables.

Associations between national viral hepatitis policies/programmes and country-level socioeconomic factors: a sub-analysis of data from the 2013 WHO viral hepatitis policy report.

PubMed

Lazarus, Jeffrey V; Sperle, Ida; Safreed-Harmon, Kelly; Gore, Charles; Cebolla, Beatriz; Spina, Alexander

2017-07-26

As more countries worldwide develop national viral hepatitis strategies, it is important to ask whether context-specific factors affect their decision-making. This study aimed to determine whether country-level socioeconomic factors are associated with viral hepatitis programmes and policy responses across WHO Member States (MS). WHO MS focal points completed a questionnaire on national viral hepatitis policies. This secondary analysis of data reported in the 2013 Global Policy Report on the Prevention and Control of Viral Hepatitis in WHO Member States used logistic regression to examine associations between four survey questions and four socioeconomic factors: country income level, Human Development Index (HDI), health expenditure and physician density. This analysis included 119 MS. MS were more likely to have routine viral hepatitis surveillance and to have a national strategy and/or policy/guidelines for preventing infection in healthcare settings if they were in the higher binary categories for income level, HDI, health expenditure and physician density. In multivariable analyses, the only significant finding was a positive association between having routine surveillance and being in the higher binary HDI category (adjusted odds ratio 26; 95% confidence interval 2.0-340). Countries with differing socioeconomic status indicators did not appear to differ greatly regarding the existence of key national policies and programmes. A more nuanced understanding of the multifaceted interactions of socioeconomic factors, health policy, service delivery and health outcomes is needed to support country-level efforts to eliminate viral hepatitis.

Inequality in the distribution of rheumatologists in Brazil: correlation with local of medical residency, Gross Domestic Product and Human Development Index.

PubMed

de Albuquerque, Cleandro Pires

2014-01-01

To assess the distribution of rheumatologists in Brazil and their correlation with Medical Residency specialization offer, Gross Domestic Product (Gdp) And Municipal Human Development Index (HDI-M) of units of the federation (UFs). Query to various official databases, data summarization by techniques for descriptive statistics and cross-referenced information. For correlation analysis, we used the Spearman correlation coefficient (r). There were 1229 rheumatologists regularly registered in the country. The Northern region had only 3.6% of the total (n = 44), while the Southeast had 42.2% (n = 519). The State capitals, added to the five largest municipalities in each UF, concentrated 75.8% of these specialists (n = 931). In total, 49.9% of rheumatologists offered treatment at SUS. A general ratio of 157,809 inhabitants per rheumatologist in Brazil was determined, but with wide variation among UFs with respect to this ratio. In the years 2000-2012, there were 593 Rheumatology Residency graduated physicians in Brazil. We observed a positive correlation among number of rheumatologists compared with GDP (r = 0.94), HDI-M of the State capitals (r = 0.77) and number of Rheumatology Residency graduated physicians (r = 0.79) in UFs. We noted a strong concentration of rheumatologists in State capitals and larger municipalities, with noticeable inequalities also between UFs and country regions. The distribution of these professionals accompanied GDP, HDI-M of the State capital and number of Rheumatology Residency graduated physicians, suggesting that factors related to income opportunities and human development and the place of speciality training may influence the geographical fixation of rheumatologists.

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE PAGES

Song, Bo; Nelson, Kevin

2015-09-01

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Longitudinal and Cross-sectional Analyses of Lung Function in Toluene Diisocyanate Production Workers.

PubMed

Wang, Mei Lin; Storey, Eileen; Cassidy, Laura D; Doney, Brent; Conner, Patrick R; Collins, James J; Carson, Michael; Molenaar, Don

2017-12-01

The aim of this study was to investigate lung function among toluene diisocyanate (TDI) production workers. One hundred ninety-seven U.S workers performed spirometry from 2006 through 2012. Results were compared within the study cohort and with U.S. population measures. A mixed-effects model assessed factors affecting repeated forced expiratory volume in 1 second (FEV1) measurements. The cohort's mean FEV1 and forced vital capacity (FVC) percent reference values, although greater than 90%, were significantly lower and the prevalence of abnormal spirometry (predominantly restrictive pattern) was significantly higher than in the U.S. Differences in lung function among workers with higher cumulative TDI exposure were in the direction of an exposure effect, but not significant. We found little evidence of an adverse effect of TDI exposure on longitudinal spirometry in these workers. The association between TDI exposure and the increasing prevalence of a restrictive pattern needs further exploration.

Dynamic characterization of frequency response of shock mitigation of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Bo; Nelson, Kevin

Kolsky compression bar experiments were conducted to characterize the shock mitigation response of a polymethylene diisocyanate (PMDI) based rigid polyurethane foam, abbreviated as PMDI foam in this study. The Kolsky bar experimental data was analyzed in the frequency domain with respect to impact energy dissipation and acceleration attenuation to perform a shock mitigation assessment on the foam material. The PMDI foam material exhibits excellent performance in both energy dissipation and acceleration attenuation, particularly for the impact frequency content over 1.5 kHz. This frequency (1.5 kHz) was observed to be independent of specimen thickness and impact speed, which may represent themore » characteristic shock mitigation frequency of the PMDI foam material under investigation. The shock mitigation characteristics of the PMDI foam material were insignificantly influenced by the specimen thickness. As a result, impact speed did have some effect.« less

Design of a high definition imaging (HDI) analysis technique adapted to challenging environments

NASA Astrophysics Data System (ADS)

Laurent, Sophie Nathalie

2005-11-01

This dissertation describes a new comprehensive, flexible, highly-automated and computationally-robust approach for high definition imaging (HDI), a data acquisition technique for video-rate imaging through a turbulent atmosphere with telescopes not equipped with adaptive optics (AO). The HDI process, when applied to astronomical objects, involves the recording of a large number of images (10 3 -10 5 ) from the Earth and, in post-processing mode, selection of the very best ones to create a "perfect-seeing" diffraction-limited image via a three-step process. First, image registration is performed to find the exact position of the object in each field, using a template similar in size and shape to the target. The next task is to select only higher-quality fields using a criterion based on a measure of the blur in a region of interest around that object. The images are then shifted and added together to create an effective time exposure under ideal observing conditions. The last step's objective is to remove residual distortions in the image caused by the atmosphere and the optical equipment, using a point spread function (PSF), and a technique called "l 1 regularization" that has been adapted to this type of environment. In order to study the tenuous sodium atmospheres around solar system bodies, the three-step HDI procedure is done first in the white light domain (695-950 nm), where the Signal-to-Noise Ratio (SNR) of the images is high, resulting in an image with a sharp limb. Then the known selection and registration results are mapped to the simultaneously recorded spectral data (sodium lines: 589 and 589.6 nm), where the lower-SNR images cannot support independent registration and selection. Science results can then be derived from this spectral study to understand the structure of the atmospheres of moons and planets. This dissertation's contribution to space physics deals with locating the source of escaping sodium from Jupiter's moon lo. The results show, for the first time, that the source region is not homogeneously distributed around the small moon, but concentrated on its side of orbital motion. This identifies for modelers the physical mechanisms taking place around the most volcanic moon in the solar system.

Mortality differences between the foreign-born and locally-born population in France (2004-2007).

PubMed

Boulogne, Roxane; Jougla, Eric; Breem, Yves; Kunst, Anton E; Rey, Grégoire

2012-04-01

In contrast to the situation in many European countries, the mortality of immigrants in France has been little studied. The main reasons for the lack of studies are based on ethical and ideological considerations. The objective of this study is to explore mortality by country of birth in Metropolitan (i.e. 'mainland') France. Complete mortality data were used to study the relative risks of mortality of the foreign- and locally-born populations by gender, age and cause of death for the period 2004-2007 in Metropolitan France. Analyses were conducted by countries of birth grouped into geographic areas and by the Human Development Index (HDI). The differentials in mortality between foreign-born and locally-born populations were not homogeneous. The figures varied by age (higher foreign-born mortality for the young; lower mortality for migrants aged 15-64 years), gender (female migrants more frequently had higher relative mortality than men migrants), country of birth (Eastern European-born migrants had higher mortality, while those born in Morocco, Central Asia, 'other Asian countries' and America had lower mortality) and cause of death (migrant mortality was higher overall for deaths caused by infectious diseases and diabetes, and lower for violent death and neoplasm). Moreover, mortality relative risks for male, violent deaths and cancer were positively associated with country-of-birth HDI, while female mortality and infectious disease mortality were negatively associated with country-of-birth HDI. Some important caveats have to be considered because the study did not control for individuals socioeconomic position in France, or length of residence in the host country. A strong healthy migrant effect was suggested and its intensity varies with age and gender (which may reflect different reasons for migration). For some specific causes of death, a lifestyle effect seems to explain mortality differentials. The associations between HDI and mortality show that mortality trends are partly related to the educational, sanitary and economic conditions of the country of birth. Further studies would enrich the differential analysis of mortality by country of birth by contributing additional detailed data on socioeconomic and living conditions in the host country as well as in the country of origin. Copyright © 2012 Elsevier Ltd. All rights reserved.

Synthesis, morphology and dynamics of polyureas and their lithium ionomers

NASA Astrophysics Data System (ADS)

Chuayprakong, Sunanta

Electrolytes currently used in commercial lithium ion batteries have led to leakage and safety issues. Solvent-free solid polymer electrolytes (SPEs) offering high energy density are promising materials for lithium battery applications. SPEs require high modulus to separate the electrodes and suppress lithium dendrite growth. Microphase separation of the hard segments in amorphous polyureas (PUs) yields materials with higher moduli than typical low glass transition temperature (Tg) polymers. In this dissertation, several families of solution polymerized polyether-based PU ionomers were synthesized and their thermal, morphology and dynamic properties characterized as a function of chemical composition. In the initial phase of this investigation, polyethylene oxide (PEO) diamines (with molecular weights = 200, 600, 1050, 2000, 3000 and 6000 g/mol) were polymerized with 4,4' methylene diphenyl diisocyanate (MDI). PUs with 200 and 600 g/mol PEO soft segments are amorphous and single phase. The amorphous PU having 1050 g/mol PEO segments exhibits a small degree of phase separation, as demonstrated by X-ray scattering. PUs with 2000, 3000 and 6000 g/mol PEO soft segments are semicrystalline and their melting points and degrees of crystallinity are lower than those of the precursor PEO diamines due to their attachment to rigid hard segments. Even though polypropylene oxide (PPO) does not dissolve cations as efficiently as PEO, PPO is not crystallizable and was chosen to create a second family of amorphous PUs. PPO-containing diamines ((Jeff400 (MW = 400 g/mol) and Jeff2000 (MW = 2000 g/mol)) and MDI were chosen as the neutral soft segment and the hard segment, respectively. 2,5-diaminobenzene sulfonate was successfully synthesized and used for preparing ionomers. The amount of ionic species in these ionomers was varied and quantified using 1H-NMR. Single Tgs were observed and they increased with increasing ionic content. No X-ray scattering peaks corresponding to microphase separation of hard and soft segments were detected, nor were ordered hydrogen bonded carbonyl bands in FTIR spectra, demonstrating that the Jeff400 PUs are single phase. Using dielectric relaxation spectroscopy (DRS), segmental relaxation temperatures also increase with increasing ionic species content.. Increasing the number of ionic groups increases the hard segment content, which results in higher DSC Tgs and slower fmaxs for the segmental relaxation processes. For the non-ionic and all of the ionic Jeff2000 PU samples that contain some nonionic soft segments, low temperature Tgs were observed that arise from microphase separated soft phases. X-ray scattering peaks related to microphase separation and ordered hydrogen bonded carbonyl bands were observed, reinforcing the conclusion of hard/soft segment segregation. The DRS segmental relaxation is associated with soft phase relaxation, with some of the ion dipoles participating in this process for the ionic samples. The ionomers could not be dialyzed due to water insolubility, but were purified by multiple precipitation in deionize water. Nevertheless, the findings suggest that the observed conductivity primarily arises from ionic impurities. A third family of PU ionomers was synthesized using an amorphous polypropylene oxide-b- polyethylene oxide-b-polypropylene oxide diamine (ED900, MW = 900 g/mol, 68% EO) and 2,5-diaminobenzene sulfonate. Hexamethylene diisocyanate was utilized as the hard segment as its high packing efficiency is known to facilitate microphase separation. The non-ionic ED900 PU and its ionomers with various ion contents were successfully synthesized. Low Tgs due to segregation of soft segments, X-ray scattering peaks related to microphase separation between segments, and ordered hydrogen bonded carbonyl bands were detected. Tapping mode atomic force microscopy was also used to explore the morphology of these microphase separated materials. DRS segmental relaxations are associated with soft phase. These materials were extensively dialyzed and their low conductivities suggest that the lithium ions are primarily trapped in hard domains.

A survey of occupational exposure to 4,4'-methylene-bis (2-chloroaniline) (MbOCA) in the UK.

PubMed

Cocker, J; Cain, J R; Baldwin, P; McNally, K; Jones, K

2009-07-01

The main objective of the study was to gather information about the current controls and levels of exposure to 4,4'-methylene-bis (2-chloroaniline) (MbOCA) in a representative cross section of workplaces that use it to manufacture polyurethane elastomers. The study also aimed to investigate whether controls and guidance could be improved and to investigate exposure to isocyanates in these workplaces using biological monitoring. An occupational hygienist and a field scientist visited the two UK suppliers and 20 out of the 25 workplaces known to be using MbOCA in the UK during 2005 and 2006. They collected air samples, surface wipes, gloves, and urine samples and made observations to assess exposure and the adequacy of controls. All samples were analysed for MbOCA and urine samples were additionally analysed for isocyanate metabolites. A statistical analysis was made of the results. Only 2.5% of the 80 personal inhalation exposures to MbOCA exceeded the workplace exposure limit of 5 microg m(-3) 8-h time-weighted average and 84% were below the limit of detection (LOD). Surface samples (n = 334) were collected from MbOCA users and suppliers and 60% had detectable levels of MbOCA ranging from 0.019 to 400 microg cm(-2). The highest levels were around a hopper, ovens, and the weighing and pouring areas. MbOCA was also detected in 8 of the 75 samples collected from areas not likely to be in contact with MbOCA. At the two suppliers, samples (n = 28) were collected from the outside surfaces of recently imported kegs, pallets, and the floor around kegs. Six samples had detectable levels and four of these (0.2, 0.8, 1, and 6 microg cm(-2)) were from the floor and pallets in both suppliers. The other two positive results were found on the outside rim (18 microg cm(-2)) and side (23 microg cm(-2)) of a keg at one supplier indicating contamination by the manufacturer. Urine samples (n = 79) were collected and 49% were below the LOD for MbOCA and only three samples had levels of MbOCA that exceeded the biological monitoring guidance value (BMGV) of 15 micromol mol(-1) creatinine. The highest urinary MbOCA concentrations were in samples from workers casting and moulding. The 90th percentile of the urine MbOCA results was 8.6 micromol MbOCA per mol creatinine. Urine samples were also analysed for the diamine metabolites of toluene diisocyanate and hexamethylene diisocyanate and 33% had detectable levels with 22 and 13% of results, respectively, above the BMGV for isocyanates (1 micromol isocyanate-derived diamine per mol creatinine). The maximum urinary concentration of toluene diamine and hexane diamine were 15.6 and 10.1 micromol mol(-1) creatinine, respectively. The survey found that the measures used to control exposure to MbOCA could be improved. Although air levels of MbOCA were generally low, there was evidence of spread of surface contamination and poor maintenance of controls such as local exhaust ventilation. A BMGV based on the 90th percentile of data from workplaces with good control would be less than the 90% value of 8.6 micromol mol(-1) creatinine found in this study and suggests that the current BMGV of 15 micromol mol(-1) creatinine is no longer acting as a stimulus to reduce exposure. The metabolites of isocyanates found in urine samples in this study could arise from inhalation exposure to isocyanates or from dermal exposure to either isocyanates or their diamine breakdown product and need further investigation.

Introduction to Rocket Propulsion

DTIC Science & Technology

1991-12-01

such as epoxies, MAPO (a trifunctional aziridinyl phosphine oxide), MT-4, various isocyanates, such a TDI, HDI, IPDI, and polyols such as trimethylol...propane (2) Burning rate catalysts, such as copper chromite (or chromate), ferrocene , and several less migratory derivatives of this organic iron

75 FR 37795 - Certain New Chemicals; Receipt and Status Information

Federal Register 2010, 2011, 2012, 2013, 2014

2010-06-30

...-methyl-, polymer with alkyl 2- propenoates, ethenyl acetate and methyl-2- methyl-2-propenoate P-10-0389...), polymers with cycloaliphatic diamine, alkyldiisocyanate, alpha-hydro-omega- hydroxy(alkyldiyl) and... dicarboxylic acid, polymer with cycloaliphatic diamine, aliphatic diisocyanate, aliphatic dicarboxylic acid...

Early adolescent childbearing in low- and middle-income countries: associations with income inequity, human development and gender equality.

PubMed

Decker, Michele R; Kalamar, Amanda; Tunçalp, Özge; Hindin, Michelle J

2017-03-01

Reducing unwanted adolescent childbearing is a global priority. Little is known about how national-level economic and human development indicators relate to early adolescent childbearing. This ecological study evaluates associations of Gross Domestic Product (GDP), GINI index, Human Development Index (HDI) and Gender-related Development Index (GDI; i.e. the HDI adjusted for gender disparities) with early adolescent childbearing in 27 low- and middle-income countries (LMICs) across three time periods. Among women ages 18–24, prevalence estimates for early birth (<16 years) were calculated by nation, and weighted linear regressions evaluated associations between national indicators and early childbearing. To examine temporal trends, analyses were stratified by year groupings. Early adolescent childbearing declined over time, with the greatest change observed in Bangladesh (31.49% in 1996/7 to 19.69% in 2011). In adjusted models, GDI was negatively associated with early childbearing, i.e. early childbearing prevalence decreased as GDI increased. In the most recent time period, relative to the lowest GDI group, the average prevalence of early childbearing was significantly lower in the middle (-12.40, P < 0.00) and upper (-10.96, P = 0.03) tertiles after adjustment for the other indicators. These other indicators showed no consistent association with early childbearing. As national-level GDI increased, early adolescent childbearing declined. The GDI, which reflects human development adjusted for gender disparities in educational and economic prospects, was more consistently related to early adolescent childbearing than the absolute development prospects as given by the HDI. While creating gender equality is an important goal in and of itself, the findings emphasize the potential for improved national-level gender equitable development as a means to improve adolescents’ sexual and reproductive health.

Trends in frequency of type 2 diabetes in Mexico and its relationship to dietary patterns and contextual factors.

PubMed

Soto-Estrada, Guadalupe; Moreno Altamirano, Laura; García-García, Juan José; Ochoa Moreno, Iván; Silberman, Martín

To analyse the evolution of the frequency of type 2 diabetes (T2D) and its relationship to eating patterns in Mexico from 1961 to 2013, and the Gini coefficient, Human Development Index (HDI) and Gross Domestic Product (GDP). Mexico ranked sixth in world prevalence of diabetes in 2015 with an estimated 11.4 million Mexicans affected. Using data from the Balance Sheets Food published by the Food and Agriculture Organization of the United Nations (FAO), the means of apparent food consumption (kcal/person/day) were grouped by decades. Data for mortality rate for diabetes were obtained from 1990 until 2015. Spearman's correlation coefficient was calculated between the diabetes mellitus mortality rate and all food groups. Pearson's correlation explored the relationship between socio economic indicators and the prevalence of T2D diabetes. The mortality rate for T2D has increased over the last decades. An increase of 647.9kcal/person/day in apparent food consumption was observed. Cereal and legume consumption decreased, while apparent sugar, animal food and animal fat and vegetable oil consumption increased substantially. HDI and GDP showed a directly proportional relationship to diabetes. Spearman's correlation coefficient was statistically significant only for sugar. The Gini coefficient suggests that in lower inequalities there is an increased frequency of diabetes. The increase in the mortality rate of type 2 diabetes was constant during the study period, which coincides with the increase in energy density of Mexican eating patterns from 1961 to 2013. The higher the Gini coefficient, HDI and GDP, the higher the mortality observed for diabetes. Copyright © 2017 SESPAS. Publicado por Elsevier España, S.L.U. All rights reserved.

Study of Barrier to Help Seeking and its Relationships with Disability in Patients with Headache.

PubMed

John, Deepa; Ram, Dushad; Sundarmurthy, Harsha; Rathod, Harshal; Rathod, Snehal

2016-10-01

Headache is among the first three most prevalent disorders with a wide treatment gap due to barriers in help seeking. Headache has been associated with disability. However, the relationship of barriers to help-seeking and disability are unexplored. To find out the barriers to help seeking and its relationship with headache related disability in patients with headache. In this hospital based cross-sectional study, 200 consecutive subjects with headache attending a tertiary care centre were recruited as per selection criteria and assessed with Sociodemographic & Clinical Proforma, Mini International Neuropsychiatric Interview (MINI), Barriers to Help Seeking Scale (BHSS), The Henry Ford Hospital Headache Disability Inventory (HDI). High mean score was observed on BHSS subscale need for control and self reliance (19.45; SD ±9.66) and minimizing problem and resignation (10.02; SD ±6.98). Mean score on the HDI was 25.65 (SD ± 14.09). Socioeconomic status of the patient was statistically significant and positively associated with need for control and self reliance (p=0.035), concrete barriers and distrust of care givers (p=0.039), emotional control (p=0.005), and privacy (p=0.002). Occupational status had significant association with need for control and self-reliance (p=0.01), minimizing problem and resignation (p=0.033), and emotional control (p=0.006). Score on hospital headache disability inventory significantly predicted the value of score on concrete barriers and distrust of caregivers domain of HDI (p=0.001). Autonomy and under estimation of seriousness of headache are common barriers to help seeking. Pattern of help seeking barriers may vary with socio-economic status and occupational status, while disability varies with gender and severity of headache. Headache associated disability is positively associated with concrete barriers.

Neuroblastoma among children in Southern and Eastern European cancer registries: Variations in incidence and temporal trends compared to US.

PubMed

Georgakis, Marios K; Dessypris, Nick; Baka, Margarita; Moschovi, Maria; Papadakis, Vassilios; Polychronopoulou, Sophia; Kourti, Maria; Hatzipantelis, Emmanuel; Stiakaki, Eftichia; Dana, Helen; Bouka, Evdoxia; Antunes, Luis; Bastos, Joana; Coza, Daniela; Demetriou, Anna; Agius, Domenic; Eser, Sultan; Gheorghiu, Raluca; Sekerija, Mario; Trojanowski, Maciej; Zagar, Tina; Zborovskaya, Anna; Ryzhov, Anton; Tragiannidis, Athanassios; Panagopoulou, Paraskevi; Steliarova-Foucher, Eva; Petridou, Eleni Th

2018-05-15

Neuroblastoma comprises the most common neoplasm during infancy (first year of life). Our study describes incidence of neuroblastoma in Southern-Eastern Europe (SEE), including - for the first time - the Nationwide Registry for Childhood Hematological Malignancies and Solid Tumors (NARECHEM-ST)/Greece, compared to the US population, while controlling for human development index (HDI). Age-adjusted incidence rates (AIR) were calculated for 1,859 childhood (0-14 years) neuroblastoma cases, retrieved from 13 collaborating SEE registries (1990-2016), and were compared to those of SEER/US (N = 3,166; 1990-2012); temporal trends were assessed using Poisson regression and Joinpoint analyses. The overall AIR was significantly lower in SEE (10.1/million) compared to SEER (11.7 per million); the difference was maximum during infancy (43.7 vs. 53.3 per million, respectively), when approximately one-third of cases were diagnosed. Incidence rates of neuroblastoma at ages <1 and 1-4 years were positively associated with HDI, whereas lower median age at diagnosis was correlated with higher overall AIR. Distribution of primary site and histology was similar in SEE and SEER. Neuroblastoma was slightly more common among males compared to females (male-to-female ratio: 1.1), mainly among SEE infants. Incidence trends decreased in infants in Slovenia, Cyprus and SEER and increased in Ukraine and Belarus. The lower incidence in SEE compared to SEER, especially in infants living in low HDI countries possibly indicates a lower level of overdiagnosis in SEE. Hence, increases in incidence rates in infancy noted in some subpopulations should be carefully monitored to avoid the unnecessary costs health impacts of tumors that could potentially spontaneously regress. © 2017 UICC.

Adherence to dietary guidelines and cardiovascular disease risk in the EPIC-NL cohort.

PubMed

Struijk, Ellen A; May, Anne M; Wezenbeek, Nick L W; Fransen, Heidi P; Soedamah-Muthu, Sabita S; Geelen, Anouk; Boer, Jolanda M A; van der Schouw, Yvonne T; Bueno-de-Mesquita, H Bas; Beulens, Joline W J

2014-09-20

Global and national dietary guidelines have been created to lower chronic disease risk. The aim of this study was to assess whether greater adherence to the WHO guidelines (Healthy Diet Indicator (HDI)); the Dutch guidelines for a healthy diet (Dutch Healthy Diet-index (DHD-index)); and the Dietary Approaches to Stop Hypertension (DASH) diet was associated with a lower risk of cardiovascular disease (CVD), coronary heart disease (CHD) or stroke. A prospective cohort study was conducted among 33,671 healthy Dutch men and women aged 20-70 years recruited into the EPIC-NL study during 1993-1997. We used Cox regression adjusted for relevant confounders to estimate the hazard ratios per standard deviation increase in score and 95% confidence intervals (CI) of the associations between the dietary guidelines and CVD, CHD and stroke risk. After an average follow-up of 12.2 years, 2752 CVD cases were documented, including 1630 CHD cases and 527 stroke cases. We found no association between the HDI (0.98, 95% CI 0.94; 1.02) or DHD-index (0.96, 95% CI 0.92; 1.00) and CVD incidence. Similar results were found for these guidelines and CHD or stroke incidence. Higher adherence to the DASH diet was significantly associated with a lower CVD (0.92, 95% CI 0.89; 0.96), CHD (0.91, 95% CI 0.86; 0.95), and stroke (0.90, 95% CI 0.82; 0.99) risk. The HDI and the DHD-index were not associated with CVD risk, while the DASH diet was significantly associated with a lower risk of developing CVD, CHD and stroke. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

Reduced carbon intensity in highly developed countries: environmental kuznets curves for carbon dioxide

NASA Astrophysics Data System (ADS)

Kornhuber, Kai; Rybski, Diego; Costa, Luis; Reusser, Dominik E.; Kropp, Jürgen P.

2014-05-01

The Environmental Kuznets Curves (EKC) postulates that pollution increases with the income per capita up to a maximum, above which it decreases with the further increase in income per capita, i.e. following an inverse U-shape in the pollution vs. income per capita. It is commonly believed that EKC occurs for "local" pollutants such as nitrogen oxide and sulfur dioxide, but does not hold for CO2 emissions. This is attributed to the fact that while "local" pollutants cause a visible environmental damage on the local/regional scale (which authorities/governments seek to avoid), the consequences of CO2 emission have no immediate attributable local/regional consequences. We review EKC for CO2 exploring its relation between CO2 per capita and the Human Development Index (HDI) between 1990 and 2010 obtained from the World Bank database. We find evidence for a reduction in CO2 emissions per capita in highly developed countries. We propose a model according to which the emissions per capita of a country are composed of a component related to the actual state of development and a component related to the change of development. The model leads to four distinct cases of which two have EKC shape and two imply saturation. This outcome is in line with previously suggested qualitative relations. Our analysis indicates that the EKC shaped cases better describes the empirical values. We explore the less extreme version corresponding to the so-called conventional EKC and study the maximum of the fitted curve, providing a threshold-value for the HDI and a typical maximum value for the emissions per capita. We find that approx. 5 countries have crossed the CO2-HDI maximum, corresponding to approx. 1.5% of the world population.

IQ as moderator of terminal decline in perceptual and motor speed, spatial, and verbal ability: Testing the cognitive reserve hypothesis in a population-based sample followed from age 70 until death.

PubMed

Thorvaldsson, Valgeir; Skoog, Ingmar; Johansson, Boo

2017-03-01

Terminal decline (TD) refers to acceleration in within-person cognitive decline prior to death. The cognitive reserve hypothesis postulates that individuals with higher IQ are able to better tolerate age-related increase in brain pathologies. On average, they will exhibit a later onset of TD, but once they start to decline, their trajectory is steeper relative to those with lower IQ. We tested these predictions using data from initially nondemented individuals (n = 179) in the H70-study repeatedly measured at ages 70, 75, 79, 81, 85, 88, 90, 92, 95, 97, 99, and 100, or until death, on cognitive tests of perceptual-and-motor-speed and spatial and verbal ability. We quantified IQ using the Raven's Coloured Progressive Matrices (RCPM) test administrated at age 70. We fitted random change point TD models to the data, within a Bayesian framework, conditioned on IQ, age of death, education, and sex. In line with predictions, we found that 1 additional standard deviation on the IQ scale was associated with a delay in onset of TD by 1.87 (95% highest density interval [HDI; 0.20, 4.08]) years on speed, 1.96 (95% HDI [0.15, 3.54]) years on verbal ability, but only 0.88 (95% HDI [-0.93, 3.49]) year on spatial ability. Higher IQ was associated with steeper rate of decline within the TD phase on measures of speed and verbal ability, whereas results on spatial ability were nonconclusive. Our findings provide partial support for the cognitive reserve hypothesis and demonstrate that IQ can be a significant moderator of cognitive change trajectories in old age. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Work disability benefits due to musculoskeletal disorders among Brazilian private sector workers.

PubMed

Vieira, E R; Albuquerque-Oliveira, P R; Barbosa-Branco, A

2011-05-14

To evaluate the prevalence and characteristics of disability benefits due to musculoskeletal disorders (MSD) granted to Brazilian private sector workers. This was a population-based epidemiological study of MSD-related benefits among registered private sector workers (n=32 959 329). The prevalence (benefits/10 000 workers/year) of work disability benefits was calculated by gender, age, state, Human Development Index (HDI), economic activity, MSD type and work-relatedness. The prevalence of MSD-related benefits in Brazil among registered private sector workers in 2008 was 93.6/10 000 workers. The prevalence increased with age, and was higher for women (112.2) than for men (88.1), although the former had shorter benefit duration. The gender-adjusted prevalence by state varied from 16.6 to 90.3 for non-work-related, and from 7.8 to 59.6 for work-related benefits. The Brazilian states with a high-very high HDI had the highest prevalence. The top four most common types of MSD-related benefits were due to back pain, intervertebral disc disorders, sinovitis/tenosynovitis and shoulder disorders. MSD is a frequent cause of work disability in Brazil. There were differences in prevalence among economic activities and between states grouped by HDI. This study demonstrates that further evaluation of the contributing factors associated with MSD-related disability benefits is required. Factors that should be considered include production processes, political organisation, socioeconomic and educational characteristics, the compensation and recording systems, and employee-employer power relationships. These factors may play an important role in the prevalence of MSD-related disability benefits, especially in countries with large socioeconomic iniquities such as Brazil.

Reliability of CGA/LGA/HDI Package Board/Assembly (Final Report)

NASA Technical Reports Server (NTRS)

Ghaffaroam. Reza

2014-01-01

Package manufacturers are now offering commercial-off-the-shelf column grid array (COTS CGA) packaging technologies in high-reliability versions. Understanding the process and quality assurance (QA) indicators for reliability are important for low-risk insertion of these advanced electronics packages. The previous reports, released in January of 2012 and January of 2013, presented package test data, assembly information, and reliability evaluation by thermal cycling for CGA packages with 1752, 1517, 1509, and 1272 inputs/outputs (I/Os) and 1-mm pitch. It presented the thermal cycling (-55C either 100C or 125C) test results for up to 200 cycles. This report presents up to 500 thermal cycles with quality assurance and failure analysis evaluation represented by optical photomicrographs, 2D real time X-ray images, dye-and-pry photomicrographs, and optical/scanning electron Microscopy (SEM) cross-sectional images. The report also presents assembly challenge using reflowing by either vapor phase or rework station of CGA and land grid array (LGA) versions of three high I/O packages both ceramic and plastic configuration. A new test vehicle was designed having high density interconnect (HDI) printed circuit board (PCB) with microvia-in-pad to accommodate both LGA packages as well as a large number of fine pitch ball grid arrays (BGAs). The LGAs either were assembled onto HDI PCB as an LGA or were solder paste print and reflow first to form solder dome on pads before assembly. Both plastic BGAs with 1156 I/O and ceramic LGAs were assembled. It also presented the X-ray inspection results as well as failures due to 200 thermal cycles. Lessons learned on assembly of ceramic LGAs are also presented.

Structural wood panels with improved fire resistance

NASA Technical Reports Server (NTRS)

Sawko, P. M. (Inventor)

1980-01-01

Structural wood paneling or other molded wood compositions consisting of finely divided wood chips, flour, or strands are bound together and hot pressed with a modified novolac resin which is the cured product of a prepolymer made from an aralkyl ether or halide with a phenol and a hardening agent such as hexamethylene tetramine. The fire resistance of these articles is further improved by incorporating in the binder certain inorganic fillers, especially a mixture of ammonium oxalate and ammonium phosphate.

A functionalizable reverse thermal gel based on a polyurethane/PEG block copolymer

PubMed Central

Park, Daewon; Wu, Wei; Wang, Yadong

2010-01-01

Injectable reverse thermal gels have great potentials as biomaterials for tissue engineering and drug delivery. However, most existing gels lack functional groups that can be modified with biomolecules that can guide cell/material interactions. We created an amine-functionalized ABA block copolymer, poly(ethylene glycol)-poly(serinol hexamethylene urethane), or ESHU. This reverse thermal gel consists of a hydrophobic block (B): poly(serinol hexamethylene urethane) and a hydrophilic block (A): poly(ethylene glycol). The polymer was characterized by GPC, FTIR and 1H FTNMR. Rheological study demonstrated that ESHU solution in phosphate-buffered saline initiated phase transition at 32°C and reached maximum elastic modulus at 37°C. The in vitro degradation tests performed in PBS and cholesterol esterase solutions revealed that the polymer was hydrolyzable and the presence of cholesterol esterase greatly accelerated the hydrolysis. The in vitro cytotoxicity tests carried out using baboon smooth muscle cells demonstrated that ESHU had good cytocompatibility with cell viability indistinguishable from tissue culture treated polystyrene. Subcutaneous implantation in rats revealed well tolerated accurate inflammatory response with moderate ED-1 positive macrophages in the early stages, which largely resolved 4 weeks post-implantation. We functionalized ESHU with a hexapeptide, Ile-Lys-Val-Ala-Val-Ser (IKVAVS), which gelled rapidly at body temperature. We expect this new platform of functionalizable reverse thermal gels to provide versatile biomaterials in tissue engineering and regenerative medicine. PMID:20937526

Effect of Branched Gap Synthesis Parameters on Mechanical Properties of Rocket Propellants

DTIC Science & Technology

1995-12-01

modulus hydroxyl functionality glycidyl azide polymer hexanetriol hydroxy-terminated polybutadiene isophorone diisocyanate hydroxyl equivalent... hexanetriol (HT), glycerol and polyethylene glycol (PEG) with MW 600. The reaction was carried out with one polyol or a blend of two polyols and

Preparation of highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Rochow, S. E.; Stump, E. C., Jr.

1971-01-01

New polyurethanes, formed from a reaction of a prepolymer diol and a perfluorinated diisocyanate, are nonflammable and possess high corrosion resistance and good low temperature flexibility. Polymer hardness increases rapidly with increasing ratio of diisocaynate to diol, but its glass transition temperature is not adversely affected.

Developing testing methods for characterizing emissions and sources of exposures from polyurehane products

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanate compounds, amine catalysts, flame retardants, and blowing agents, as well as aldehydes and other volatile or semivolatile organic compounds that may be...

The Development of Testing Methods for Characterizing Emissions and Sources of Exposures from Polyurethane Products

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures is not well understood. Currently, no comprehensive standard test methods exist for characterizing and quantifying product emissions. Exposures to diisocyanate compoun...

Reliability of CGA/LGA/HDI Package Board/Assembly (Revision A)

NASA Technical Reports Server (NTRS)

Ghaffarian, Reza

2013-01-01

This follow-up report presents reliability test results conducted by thermal cycling of five CGA assemblies evaluated under two extreme cycle profiles, representative of use for high-reliability applications. The thermal cycles ranged from a low temperature of 55 C to maximum temperatures of either 100 C or 125 C with slow ramp-up rate (3 C/min) and dwell times of about 15 minutes at the two extremes. Optical photomicrographs that illustrate key inspection findings of up to 200 thermal cycles are presented. Other information presented include an evaluation of the integrity of capacitors on CGA substrate after thermal cycling as well as process evaluation for direct assembly of an LGA onto PCB. The qualification guidelines, which are based on the test results for CGA/LGA/HDI packages and board assemblies, will facilitate NASA projects' use of very dense and newly available FPGA area array packages with known reliably and mitigation risks, allowing greater processing power in a smaller board footprint and lower system weight.

Spatial and gender scenario of literate life expectancy at birth in India.

PubMed

Chattopadhyay, Aparajita; Sinha, Kumar Chiman

2010-10-01

Measuring human quality of life is academically challenging. The human development index (HDI) substantially captures the overall country level status on human welfare. However, this index has some drawbacks. Therefore, Lutz composed a simple index in 1995 combining life expectancy and literacy, called literate life expectancy (LLE). LLE can be calculated for subpopulations depending on availability of data. This article captures the LLE in major states in India and the gender differences in LLE at rural and urban levels. The authors have tried to highlight the social development scenario in India and its major states by using this pure social indicator that intentionally does not use any economic measurement. The state scenario comprehensively depicts gender differentials in social development, and it calls for implementing development measures more seriously in states like Haryana, Bihar, Rajasthan, Madhya Pradesh, and Uttar Pradesh to reduce the gender gap. Being highly correlated with the HDI, the LLE index proves to be a very clear and simple comprehensive measure of social development for different subpopulations.

The power of light: socio-economic and environmental implications of a rural electrification program in Brazil

NASA Astrophysics Data System (ADS)

Borges da Silveira Bezerra, Paula; Ludovique Callegari, Camila; Ribas, Aline; Lucena, André F. P.; Portugal-Pereira, Joana; Koberle, Alexandre; Szklo, Alexandre; Schaeffer, Roberto

2017-09-01

Universal access to electricity is deemed critical for improving living standards and indispensable for eradicating poverty and achieving sustainable development. In 2003, the ‘Luz para Todos’ (LpT—Light for All) program was launched aiming to universalize access to electricity in Brazil. The program focused on rural and isolated areas, also targeting to bring development to those regions along with electrification. This paper evaluates the results of the LpT program in improving socio-economic development in the poorest regions of Brazil. After an initial qualitative analysis, an empirical quantitative assessment of the influence of increased electrification rates on the components of the Human Development Index (HDI) is performed. The empirical results of this study showed that electrification had a positive influence on all dimensions of the HDI, with the education component having the strongest effect. Although complementary policies were needed to achieve this, results show that electricity access is a major requirement to improve quality of life.

Bibliometric analysis of phytotechnologies for remediation: global scenario of research and applications.

PubMed

Koelmel, Jeremy; Prasad, M N V; Pershell, Karoline

2015-01-01

Phytoremediation is often a low cost alternative to conventional remediation. To assess trends, a bibliometric approach using data from SciVerse Scopus, SciVerseHub, and GoogleTM Trends was used. Globally there is a linear increase in publications containing the word phytoremediation as a percent of all published papers in SciVerse Hub, with China, India, and the Philippines concentrating relatively more research in phytoremediation. Furthermore there was an inverse correlation between a country's Human Development Index (HDI) and a country's phytoremediation research output as a percent of total research. Results show a focus on phytoremediation in countries with low HDI values. This suggests that academic experts are available for advancing phytoremediation applications in countries where the majority of the effected population do not have the education, finances, and political leverage to obtain expensive conventional remediation efforts on their land. Phytoremediation can combine expert advice with affected parties commitment and labor to help mitigate the harms of polluted landscapes.

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2013 CFR

2013-07-01

...) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63... foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage... of pumps, valves, connectors, pressure-relief devices, and open-ended valves or lines in HAP ABA...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2014 CFR

2014-07-01

...) National Emission Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63... foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage... of pumps, valves, connectors, pressure-relief devices, and open-ended valves or lines in HAP ABA...

78 FR 37818 - Request for Information on Toluene Diisocyanates

Federal Register 2010, 2011, 2012, 2013, 2014

2013-06-24

.... engineering controls, work practices, personal protective equipment, exposure data before and after... Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) for TDI is 0.005 ppm... vitro and in vivo studies. (7) Information on control measures (e.g., engineering controls, work...

Development of test systems for characterizing emissions from spray polyurethane foam insulation (SPFI)

EPA Science Inventory

The relationship between onsite manufacture of spray polyurethane foam insulation (SPFI) and potential exposures to diisocyanates, amines, flame retardants (FRs), blowing agents, aldehydes and other organic compounds that may be emitted from SPFI is not well understood. EPA is de...

Determination of albumin adducts of 4,4'-methylenediphenyl diisocyanate after specific inhalative challenge tests in workers.

PubMed

Sabbioni, Gabriele; Dongari, Nagaraju; Kumar, Anoop; Baur, Xaver

2016-10-17

4,4'-Methylenediphenyl diisocyanate (MDI) is the most important isocyanate used in the industry. Lung sensitization with bronchial asthma is the main disorder in exposed workers. Albumin adducts of MDI might be involved in specific immunological reactions. MDI adducts with lysine (MDI-Lys) of albumin have been found in MDI-workers and construction workers. MDI-Lys is an isocyanate-specific adduct of MDI with albumin. In the present study, we report MDI-adducts in workers undergoing diagnostic MDI challenge tests. The workers were exposed for 2h to 5ppb of MDI. The adduct levels increase significantly after the exposure to MDI in the challenge chamber. About 0.6% of the dose was bound to albumin. So far, only urinary metabolites of MDI were measured to monitor isocyanate workers. However, such urinary metabolites are not isocyanate specific. Therefore, we propose to measure albumin adducts for monitoring MDI exposed subjects. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Evaluation of workers' exposure to methylene diphenyl diisocyanate (MDI) in an automobile manufacturing company, Iran.

PubMed

Kakooei, Hossein; Shahtaheri, Seyed Jamaleddin; Karbasi, Hossein-Ali

2006-01-01

Evaluation of personal inhalation exposure to methylene diphenyl diisocyanate (MDI) among 39 employees, working in the window fixation and window glue processes in an automobile manufacturing company was performed. This study was conducted for both case and control groups. After sampling and sample preparation processes, MDI was determined with a UV-VIS spectrophotometer at 590 nm; the lung function was assessed with a digital spirometer, too. The average concentration of MDI in the window fixation, and window glue workplaces were 34.53 and 27.37 micro g/m3, respectively, which was lower than the threshold limit value (TLV) recommended by the American Conference of Governmental Industrial Hygienists (ACGIH) (51 micro g/m3). Respiratory symptoms in the exposed group were significantly different compared to the unexposed group (p < .05). Lung capacities in the case group were lower than in the control group (p < .05). Therefore, MDI can be easily measured making it possible to evaluate the adverse effects caused by occupational exposure.

Modeling Heat Transfer and Pressurization of Polymeric Methylene Diisocyanate (PMDI) Polyurethane Foam in a Sealed Container.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Scott, Sarah Nicole

Polymer foam encapsulants provide mechanical, electrical, and thermal isolation in engineered systems. It can be advantageous to surround objects of interest, such as electronics, with foams in a hermetically sealed container to protect the electronics from hostile en vironments, such as a crash that produces a fire. However, i n fire environments, gas pressure from thermal decomposition of foams can cause mechanical failure of the sealed system . In this work, a detailed study of thermally decomposing polymeric methylene diisocyanate (PMDI) - polyether - polyol based polyurethane foam in a sealed container is presented . Both experimental and computational workmore » is discussed. Three models of increasing physics fidelity are presented: No Flow, Porous Media, and Porous Media with VLE. Each model us described in detail, compared to experiment , and uncertainty quantification is performed. While the Porous Media with VLE model matches has the best agreement with experiment, it also requires the most computational resources.« less

Infrared microspectroscopic study of the thermo-oxidative degradation of hydroxy-terminated polybutadiene/isophorone diisocyanate polyurethane rubber

DOE PAGES

Nagle, Dylan J.; Celina, Mathew; Rintoul, Llewellyn; ...

2007-05-21

In this work, hydroxy-terminated polybutadiene/isophorone diisocyanate (HTPB/IPDI) polyurethane rubber which was aged in air at elevated temperatures has been studied by infrared microspectroscopy. Spectra were collected in transmission mode on microtomed samples. Analysis of sets of spectra taken across the sectioned material showed that most of the degradation occurred in the polybutadiene part of the polymer and that the urethane linkage was essentially unchanged. The trans isomer of the polybutadiene appears to be preferentially degraded compared with the vinyl isomer. The IR technique does not provide significant information about the cis isomer. The IR spectra indicated that likely degradation productsmore » included acids, esters, alcohols, and small amounts of other products containing a carbonyl functional group. Band area ratios, supported by a principal components analysis, were used to derive degradation profiles for the material. Lastly, these profiles were steep-sided indicating an oxygen diffusion limited process.« less

Percentage of Children Aged 5--17 Years Ever Receiving a Diagnosis of Learning Disability, United States, 2007--2009

MedlinePlus

... Ethnicity † and Family Income Group § --- National Health Interview Survey, ¶ United States, 2007--2009 * Based on parental response ... cdc.gov/nchs/hdi.htm . National Health Interview Survey 2007--2009 data. Available at http://www.cdc. ...

Merit Goods, Education Public Policy--India at Cross Roads

ERIC Educational Resources Information Center

Misra, Satya Narayan; Ghadai, Sanjaya Ku.

2015-01-01

Merit Goods have always received handsome attention and allocation from countries which have witnessed a congruence between high significant economic growth and Human Development Index (HDI). The Emerging Market Economies (EMEs) have become significant manufacturing hubs by universalizing education and improving their Incremental Capital Output…

Potentially Prebiotic Syntheses of Condensed Phosphates

NASA Technical Reports Server (NTRS)

Keefe, Anthony D.; Miller, Stanley L.

1996-01-01

In view of the importance of a prebiotic source of high energy phosphates, we have investigated a number of potentially prebiotic processes to produce condensed phosphates from orthophosphate and cyclic trimetaphosphate from tripolyphosphate. The reagents investigated include polymerizing nitriles, acid anhydrides, lactones, hexamethylene tetramine and carbon suboxide. A number of these processes give substantial yields of pyrophosphate from orthophosphate and trimetaphosphate from tripolyphosphate. Although these reactions may have been applicable in local areas, they are not sufficiently robust to have been of importance in the prebiotic open ocean.

Chelation in metal intoxication. VIII. Removal of chromium from organs of potassium chromate administered rats.

PubMed

Behari, J R; Tandon, S K

1980-03-01

Some polyaminocarboxylic acids were examined for their ability to mobilize chromium from certain vital organs, their subcellular fractions, and blood cells of potassium chromate administered rats. Hexamethylene 1,6-diamino tetraacetic acid (TDTA), triethylene tetramine hexaacetic acid (TTHA), and ethylene diamine di (O-hydroxylphenyl acetic acid) (EDDHA) may be useful in preventing or reducing chromate toxicity. No definite relationship could be observed between the structure of the chelating agents and their chromium-removing capacity.

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2011 CFR

2011-07-01

... Standards for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2010 CFR

2010-07-01

... for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 63.1306 - Reporting requirements.

Code of Federal Regulations, 2012 CFR

2012-07-01

... for Hazardous Air Pollutants for Flexible Polyurethane Foam Production § 63.1306 Reporting... the information listed in paragraph (d)(4) of this section for molded foam processes and in paragraph (d)(5) for rebond foam processes. (1) A list of diisocyanate storage vessels, along with a record of...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2011 CFR

2011-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2013 CFR

2013-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2014 CFR

2014-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

40 CFR 261.32 - Hazardous wastes from specific sources.

Code of Federal Regulations, 2012 CFR

2012-07-01

... of vinyl chloride in vinyl chloride monomer production (T) K021 Aqueous spent antimony catalyst waste... toluene diisocyanate production (R, T) K028 Spent catalyst from the hydrochlorinator reactor in the...,1-dimethylhydrazine (UDMH) from carboxylic acid hydrazides (I,T) K109 Spent filter cartridges from...

INCONSISTENCIES BETWEEN CYTOKINE PROFILES, ANTIBODY RESPONSES, AND RESPIRATORY HYPERRESPONSIVENESS FOLLOWING DERMAL EXPOSURE TO ISOCYANATES

EPA Science Inventory

Cytokine profiling of local lymph node responses has been proposed as a simple test to identify chemicals, such as low molecular weight diisocyanates, that pose a significant risk of occupational asthma. Previously, we reported cytokine mRNA profiles for dinitrochlorobenzene (DNC...

Novel polyurethanes from xylan and TDI: Preparation and characterization

USDA-ARS?s Scientific Manuscript database

In this work a novel polyurethane was developed involving xylan and tolylene-2,4-diisocyanate (TDI). Polymer synthesis was achieved via conventional heat or microwave-assisted reaction in dimethylsulfoxide. Because xylan has multiple OH groups on each polymer chain, the TDI/xylan molar ratio neede...

Preparation of eugenol-based polyurethane

NASA Astrophysics Data System (ADS)

Li, Yupeng; Luo, Fang; Cheng, Chuanjie

2018-03-01

The regenerative eugenol was used as the starting material to prepare diol species by two steps, with a total yield of 28%. Furthermore, the prepared diol reacts with 1,6-hexadiisocyanate(HDI) to afford the corresponding polyurethane (PU). The structure of intermediates and PU are characterized by 1H-NMR or IR.

Conflict and Security Indices: A Summary of Open-Source Data

DTIC Science & Technology

2008-09-01

in the same dimensions as the HDI while adjusting for gender inequality . The Gender Empowerment Measure (GEM) measures the extent of women’s...measures gender inequality in three key areas: political participation and decision making power, as measured by women’s and men’s percentage share of

40 CFR 721.8079 - Isophorone diisocyanate neopentyl glycol adipate polyurethane prepolymer.

Code of Federal Regulations, 2010 CFR

2010-07-01

... glycol adipate polyurethane prepolymer. 721.8079 Section 721.8079 Protection of Environment ENVIRONMENTAL... adipate polyurethane prepolymer. (a) Chemical substance and significant new uses subject to reporting. (1... polyurethane prepolymer (PMN P-94-1743) is subject to reporting under this section for the significant new uses...

Liner Technology Program. Volume 3. Liner Development Methodology Manual

DTIC Science & Technology

1982-05-01

derivative of trimesic acid, trimenoyl-l- (2-ethyl) aziridine BNO Hydroxyl ethyl ester of carboxy-terminated polybutadiene Catocene Liquid ferrocene ...diisocyanate MAPO rris-l-(2-methyl) aziridinyl phosphine oxide I.’ lNA Methyl nedic anhydride; methyl endo-cis-cicyolo-2,2,1-5- heptene-2,3-dicarboxylic

40 CFR 63.1300 - Standards for molded flexible polyurethane foam production.

Code of Federal Regulations, 2013 CFR

2013-07-01

... polyurethane foam production. 63.1300 Section 63.1300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Foam Production § 63.1300 Standards for molded flexible polyurethane foam production. Each owner or... polyurethane foam process, with the following exception. Diisocyanates may be used to flush the mixhead and...

40 CFR 63.1300 - Standards for molded flexible polyurethane foam production.

Code of Federal Regulations, 2014 CFR

2014-07-01

... polyurethane foam production. 63.1300 Section 63.1300 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Foam Production § 63.1300 Standards for molded flexible polyurethane foam production. Each owner or... polyurethane foam process, with the following exception. Diisocyanates may be used to flush the mixhead and...

A COMPARISON OF CYTOKINE MESSAGE AND PROTEIN PROFILES OBTAINED FOLLOWING DERMAL EXPOSURE TO DIISOCYANATES.

EPA Science Inventory

Exposure to certain low molecular weight chemicals is associated with asthma. A simple method to identify this hazard is needed. Increased expression of Th2 cytokine mRNA in draining lymph nodes following dermal exposure and increased production of Th2 cytokines by cultured cell...

Neighborhoods in Development: Human Development Index and Self-Organizing Maps

ERIC Educational Resources Information Center

Rende, Sevinc; Donduran, Murat

2013-01-01

The Human Development Index (HDI) has been instrumental in broadening the discussion of economic development beyond money-metric progress, in particular, by ranking a country against other countries in terms of the well being of their citizens. We propose self-organizing maps to explore similarities among countries using the components of the HDI…

Rethinking the Place of Children and Youth

ERIC Educational Resources Information Center

Schissel, Bernard; Schissel, Wendy

2008-01-01

According to the annual United Nations declarations based on the Human Development Index (HDI), Canada remains one of the best places in the world in which to live. Ironically, this declaration of socio-economic superiority does not extend to the young people in the society. Although post-industrial societies like Canada and the United States may…

Using the HDI camera with Tohono O’odham Tribal Community College Students

NASA Astrophysics Data System (ADS)

Garmany, Catharine D.

2017-01-01

Tohono O’odham Community College is a small two-year tribal college, located at the foot of I'oligam Du'ag, also known as Kitt Peak. In recognition and appreciation of Kitt Peak National Observatory’s location on the Tohono O’odham reservation, NOAO has worked with the college to offer an introduction astronomy class when requested. The class has been taught by NOAO scientific staff and post docs, and the lab component of this 4-credit class has been carried out at Kitt Peak. With support from the WIYN0.9-m Consortium, students have been able to observe on the 0.9m telescope. Most recently they have used the HDI camera for an evening, which has been a highlight of the class that students always note in their final evaluation. I will describe challenges and rewards in developing and maintaining this class, including identifying post docs and graduate students who are able to teach it. However, we feel the challenges are worth it: this may be the only formal astronomy class offered at a tribal college.

The Dynamics of Democracy, Development and Cultural Values

PubMed Central

Spaiser, Viktoria; Ranganathan, Shyam; Mann, Richard P.; Sumpter, David J. T.

2014-01-01

Over the past decades many countries have experienced rapid changes in their economies, their democratic institutions and the values of their citizens. Comprehensive data measuring these changes across very different countries has recently become openly available. Between country similarities suggest common underlying dynamics in how countries develop in terms of economy, democracy and cultural values. We apply a novel Bayesian dynamical systems approach to identify the model which best captures the complex, mainly non-linear dynamics that underlie these changes. We show that the level of Human Development Index (HDI) in a country drives first democracy and then higher emancipation of citizens. This change occurs once the countries pass a certain threshold in HDI. The data also suggests that there is a limit to the growth of wealth, set by higher emancipation. Having reached a high level of democracy and emancipation, societies tend towards equilibrium that does not support further economic growth. Our findings give strong empirical evidence against a popular political science theory, known as the Human Development Sequence. Contrary to this theory, we find that implementation of human-rights and democratisation precede increases in emancipative values. PMID:24905920

The dynamics of democracy, development and cultural values.

PubMed

Spaiser, Viktoria; Ranganathan, Shyam; Mann, Richard P; Sumpter, David J T

2014-01-01

Over the past decades many countries have experienced rapid changes in their economies, their democratic institutions and the values of their citizens. Comprehensive data measuring these changes across very different countries has recently become openly available. Between country similarities suggest common underlying dynamics in how countries develop in terms of economy, democracy and cultural values. We apply a novel Bayesian dynamical systems approach to identify the model which best captures the complex, mainly non-linear dynamics that underlie these changes. We show that the level of Human Development Index (HDI) in a country drives first democracy and then higher emancipation of citizens. This change occurs once the countries pass a certain threshold in HDI. The data also suggests that there is a limit to the growth of wealth, set by higher emancipation. Having reached a high level of democracy and emancipation, societies tend towards equilibrium that does not support further economic growth. Our findings give strong empirical evidence against a popular political science theory, known as the Human Development Sequence. Contrary to this theory, we find that implementation of human-rights and democratisation precede increases in emancipative values.

The efficacy of oral habit modification on headache.

PubMed

Agha-Hosseini, Farzaneh; Sheykhbahaei, Nafiseh; Mirzaii-Dizgah, Iraj; Fatehi, Farzad

2017-12-01

Headache is the most common complaint of patients suffering from temporomandibular joint disorders (TMDs). Thus, temporomandibular joint (TMJ) examinations maybe necessary in patients with headache. Considering the high prevalence of bruxism and TMDs in patients with headache the effects of conservative TMD treatment on headache should be assessed. Patients were questioned about headaches in the past three months. Those responding affirmatively to this question were examined for TMD and bruxism. After the examinations, 219 patients remained in the study and received self-management instructions. Patients were requested to modify oral habits except when eating or sleeping. The degree of pain (visual analogue scale), headache disability index (HDI), frequency of headaches (FH) per month and TMD intensity were evaluated. The median levels of pain, HDI, FH, and TMD intensity were 8, 44, 8, and 7, respectively, before modifying oral habits and decreased to 4, 24, 2, and 3, respectively, after intervention. These decreases were statistically significant. Having patients maintain free space between the teeth and relax muscles can be an efficient method to treat headache and TMD, especially when repeated frequently.

Obesity and socioeconomic status in developing countries: a systematic review

PubMed Central

Dinsa, GD; Goryakin, Y; Fumagalli, E; Suhrcke, M

2012-01-01

Summary We undertook a systematic review of studies assessing the association between socioeconomic status (SES) and measured obesity in low- and middle-income countries (defined by the World Bank as countries with per capita income up to US$12,275) among children, men and women. The evidence on the subject has grown significantly since an earlier influential review was published in 2004. We find that in low-income countries or in countries with low human development index (HDI), the association between SES and obesity appears to be positive for both men and women: the more affluent and/or those with higher educational attainment tend to be more likely to be obese. However, in middle-income countries or in countries with medium HDI, the association becomes largely mixed for men and mainly negative for women. This particular shift appears to occur at an even lower level of per capita income than suggested by an influential earlier review. By contrast, obesity in children appears to be predominantly a problem of the rich in low- and middle-income countries. PMID:22764734

WHO guidelines for a healthy diet and mortality from cardiovascular disease in European and American elderly: the CHANCES project.

PubMed

Jankovic, Nicole; Geelen, Anouk; Streppel, Martinette T; de Groot, Lisette Cpgm; Kiefte-de Jong, Jessica C; Orfanos, Philippos; Bamia, Christina; Trichopoulou, Antonia; Boffetta, Paolo; Bobak, Martin; Pikhart, Hynek; Kee, Frank; O'Doherty, Mark G; Buckland, Genevieve; Woodside, Jayne; Franco, Oscar H; Ikram, M Arfan; Struijk, Ellen A; Pajak, Andrzej; Malyutina, Sofia; Kubinova, Růžena; Wennberg, Maria; Park, Yikyung; Bueno-de-Mesquita, H Bas; Kampman, Ellen; Feskens, Edith J

2015-10-01

Cardiovascular disease (CVD) represents a leading cause of mortality worldwide, especially in the elderly. Lowering the number of CVD deaths requires preventive strategies targeted on the elderly. The objective was to generate evidence on the association between WHO dietary recommendations and mortality from CVD, coronary artery disease (CAD), and stroke in the elderly aged ≥60 y. We analyzed data from 10 prospective cohort studies from Europe and the United States comprising a total sample of 281,874 men and women free from chronic diseases at baseline. Components of the Healthy Diet Indicator (HDI) included saturated fatty acids, polyunsaturated fatty acids, mono- and disaccharides, protein, cholesterol, dietary fiber, and fruit and vegetables. Cohort-specific HRs adjusted for sex, education, smoking, physical activity, and energy and alcohol intakes were pooled by using a random-effects model. During 3,322,768 person-years of follow-up, 12,492 people died of CVD. An increase of 10 HDI points (complete adherence to an additional WHO guideline) was, on average, not associated with CVD mortality (HR: 0.94; 95% CI: 0.86, 1.03), CAD mortality (HR: 0.99; 95% CI: 0.85, 1.14), or stroke mortality (HR: 0.95; 95% CI: 0.88, 1.03). However, after stratification of the data by geographic region, adherence to the HDI was associated with reduced CVD mortality in the southern European cohorts (HR: 0.87; 95% CI: 0.79, 0.96; I(2) = 0%) and in the US cohort (HR: 0.85; 95% CI: 0.83, 0.87; I(2) = not applicable). Overall, greater adherence to the WHO dietary guidelines was not significantly associated with CVD mortality, but the results varied across regions. Clear inverse associations were observed in elderly populations in southern Europe and the United States.

WHO guidelines for a healthy diet and mortality from cardiovascular disease in European and American elderly: the CHANCES project12

PubMed Central

Jankovic, Nicole; Geelen, Anouk; Streppel, Martinette T; de Groot, Lisette CPGM; Kiefte-de Jong, Jessica C; Orfanos, Philippos; Bamia, Christina; Trichopoulou, Antonia; Boffetta, Paolo; Bobak, Martin; Pikhart, Hynek; Kee, Frank; O’Doherty, Mark G; Buckland, Genevieve; Woodside, Jayne; Franco, Oscar H; Ikram, M Arfan; Struijk, Ellen A; Pajak, Andrzej; Malyutina, Sofia; Kubinova, Růžena; Wennberg, Maria; Park, Yikyung; Bueno-de-Mesquita, H Bas; Kampman, Ellen; Feskens, Edith J

2015-01-01

Background: Cardiovascular disease (CVD) represents a leading cause of mortality worldwide, especially in the elderly. Lowering the number of CVD deaths requires preventive strategies targeted on the elderly. Objective: The objective was to generate evidence on the association between WHO dietary recommendations and mortality from CVD, coronary artery disease (CAD), and stroke in the elderly aged ≥60 y. Design: We analyzed data from 10 prospective cohort studies from Europe and the United States comprising a total sample of 281,874 men and women free from chronic diseases at baseline. Components of the Healthy Diet Indicator (HDI) included saturated fatty acids, polyunsaturated fatty acids, mono- and disaccharides, protein, cholesterol, dietary fiber, and fruit and vegetables. Cohort-specific HRs adjusted for sex, education, smoking, physical activity, and energy and alcohol intakes were pooled by using a random-effects model. Results: During 3,322,768 person-years of follow-up, 12,492 people died of CVD. An increase of 10 HDI points (complete adherence to an additional WHO guideline) was, on average, not associated with CVD mortality (HR: 0.94; 95% CI: 0.86, 1.03), CAD mortality (HR: 0.99; 95% CI: 0.85, 1.14), or stroke mortality (HR: 0.95; 95% CI: 0.88, 1.03). However, after stratification of the data by geographic region, adherence to the HDI was associated with reduced CVD mortality in the southern European cohorts (HR: 0.87; 95% CI: 0.79, 0.96; I2 = 0%) and in the US cohort (HR: 0.85; 95% CI: 0.83, 0.87; I2 = not applicable). Conclusion: Overall, greater adherence to the WHO dietary guidelines was not significantly associated with CVD mortality, but the results varied across regions. Clear inverse associations were observed in elderly populations in southern Europe and the United States. PMID:26354545

Study of Barrier to Help Seeking and its Relationships with Disability in Patients with Headache

PubMed Central

John, Deepa; Sundarmurthy, Harsha; Rathod, Harshal; Rathod, Snehal

2016-01-01

Introduction Headache is among the first three most prevalent disorders with a wide treatment gap due to barriers in help seeking. Headache has been associated with disability. However, the relationship of barriers to help-seeking and disability are unexplored. Aim To find out the barriers to help seeking and its relationship with headache related disability in patients with headache. Materials and Methods In this hospital based cross-sectional study, 200 consecutive subjects with headache attending a tertiary care centre were recruited as per selection criteria and assessed with Sociodemographic & Clinical Proforma, Mini International Neuropsychiatric Interview (MINI), Barriers to Help Seeking Scale (BHSS), The Henry Ford Hospital Headache Disability Inventory (HDI). Results High mean score was observed on BHSS subscale need for control and self reliance (19.45; SD ±9.66) and minimizing problem and resignation (10.02; SD ±6.98). Mean score on the HDI was 25.65 (SD ± 14.09). Socioeconomic status of the patient was statistically significant and positively associated with need for control and self reliance (p=0.035), concrete barriers and distrust of care givers (p=0.039), emotional control (p=0.005), and privacy (p=0.002). Occupational status had significant association with need for control and self-reliance (p=0.01), minimizing problem and resignation (p=0.033), and emotional control (p=0.006). Score on hospital headache disability inventory significantly predicted the value of score on concrete barriers and distrust of caregivers domain of HDI (p=0.001). Conclusion Autonomy and under estimation of seriousness of headache are common barriers to help seeking. Pattern of help seeking barriers may vary with socio-economic status and occupational status, while disability varies with gender and severity of headache. Headache associated disability is positively associated with concrete barriers. PMID:27891430

Global temporal patterns of pancreatic cancer and association with socioeconomic development.

PubMed

Wong, Martin C S; Jiang, Johnny Y; Liang, Miaoyin; Fang, Yuan; Yeung, Ming Sze; Sung, Joseph J Y

2017-06-09

Pancreatic cancer induces a substantial global burden. We examined its global incidence/mortality rates and their correlation with socioeconomic development (Human Development Index [HDI] and Gross Domestic Product [GDP] in 2000 as proxy measures). Data on age-standardized incidence/mortality rates in 2012 were retrieved from the GLOBOCAN database. Temporal patterns in 1998-2007 were assessed for 39 countries according to gender. The Average Annual Percent Change (AAPC) of the incidence/mortality trends was evaluated using joinpoint regression analysis. The age-standardized incidence ranged between 0.8-8.9/100,000. When compared among countries, Brazil (AAPC = 10.4, 95%C.I. = 0.8,21) and France (AAPC = 4.7, 95%C.I. = 3.6,5.9) reported the highest incidence rise in men. The greatest increase in women was reported in Thailand (AAPC = 7, 95%C.I. = 2.1,12.1) and Ecuador (AAPC = 4.3, 95%C.I. = 1.3,7.3). For mortality, the Philippines (APCC = 4.3, 95%C.I. = 2,6.6) and Croatia (AAPC = 2, 95% C.I. = 0,3.9) reported the biggest increase among men. The Philippines (AAPC = 5.8, 95% C.I. 4.5,7.2) and Slovakia (AAPC = 3.1, 95% C.I. 0.9,5.3) showed the most prominent rise among women. Its incidence was positively correlated with HDI (men: r = 0.66; women: r = 0.70) and GDP (men: r = 0.29; women: r = 0.28, all p < 0.05), and similarly for mortality (men: r = 0.67; women: r = 0.72 [HDI]; men: r = 0.23; women: r = 0.28 [GDP]). In summary, the incidence and mortality of pancreatic cancer were rising in many countries, requiring regular surveillance.

Persisting inequalities in survival patterns of childhood neuroblastoma in Southern and Eastern Europe and the effect of socio-economic development compared with those of the US.

PubMed

Panagopoulou, Paraskevi; Georgakis, Marios K; Baka, Margarita; Moschovi, Maria; Papadakis, Vassilios; Polychronopoulou, Sophia; Kourti, Maria; Hatzipantelis, Emmanuel; Stiakaki, Eftichia; Dana, Helen; Tragiannidis, Athanasios; Bouka, Evdoxia; Antunes, Luis; Bastos, Joana; Coza, Daniela; Demetriou, Anna; Agius, Domenic; Eser, Sultan; Gheorghiu, Raluca; Šekerija, Mario; Trojanowski, Maciej; Žagar, Tina; Zborovskaya, Anna; Ryzhov, Anton; Dessypris, Nick; Morgenstern, Daniel; Petridou, Eleni Th

2018-06-01

Neuroblastoma outcomes vary with disease characteristics, healthcare delivery and socio-economic indicators. We assessed survival patterns and prognostic factors for patients with neuroblastoma in 11 Southern and Eastern European (SEE) countries versus those in the US, including-for the first time-the Nationwide Registry for Childhood Hematological Malignancies and Solid Tumours (NARECHEM-ST)/Greece. Overall survival (OS) was calculated in 13 collaborating SEE childhood cancer registries (1829 cases, ∼1990-2016) and Surveillance, Epidemiology, and End Results (SEER), US (3072 cases, 1990-2012); Kaplan-Meier curves were used along with multivariable Cox regression models assessing the effect of age, gender, primary tumour site, histology, Human Development Index (HDI) and place of residence (urban/rural) on survival. The 5-year OS rates varied widely among the SEE countries (Ukraine: 45%, Poland: 81%) with the overall SEE rate (59%) being significantly lower than in SEER (77%; p < 0.001). In the common registration period within SEE (2000-2008), no temporal trend was noted as opposed to a significant increase in SEER. Age >12 months (hazard ratio [HR]: 2.8-4.7 in subsequent age groups), male gender (HR: 1.1), residence in rural areas (HR: 1.3), living in high (HR: 2.2) or medium (HR: 2.4) HDI countries and specific primary tumour location were associated with worse outcome; conversely, ganglioneuroblastoma subtype (HR: 0.28) was associated with higher survival rate. Allowing for the disease profile, children with neuroblastoma in SEE, especially those in rural areas and lower HDI countries, fare worse than patients in the US, mainly during the early years after diagnosis; this may be attributed to presumably modifiable socio-economic and healthcare system performance differentials warranting further research. Copyright © 2018 Elsevier Ltd. All rights reserved.

78 FR 41853 - Safety Advisory Guidance: Heating Rail Tank Cars To Prepare Hazardous Material for Unloading or...

Federal Register 2010, 2011, 2012, 2013, 2014

2013-07-12

... rail tank car due to chemical self-reaction and expansion of the toluene diisocyanate matter wastes. On...: Cheryl West Freeman, Division of Engineering and Research, Pipeline and Hazardous Materials Safety... catastrophically ruptured at a transfer station at the BASF Corporation chemical facility in Freeport, Texas. The...

Aspen flakeboard treated with disodium octaborate tetrahydrate

Treesearch

Robert H. White; John Forsman; John R. Erickson

2008-01-01

In this project, we investigated mechanical properties and fire performance of aspen flakeboards manufactured with the fire-retardant chemical disodium octaborate tetrahydrate (DOT). Flakeboards were prepared using two levels of adhesive loading (5% and 7% methylene diphenyl diisocyanate (MDI)) and three levels of fire-retardant treatments (6%, 9%, and 12%). DOT is a...

40 CFR 721.10607 - Aliphatic diisocyanate, homopolymer, alkanol-blocked (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

...-purifying, tight-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters. (B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil...-certified powered air-purifying respirator equipped with a tight-fitting facepiece (either half-face or full...

Determination of isocyanate specific albumin-adducts in workers exposed to toluene diisocyanates.

PubMed

Sabbioni, Gabriele; Gu, Qi; Vanimireddy, Lakshiminiranjan Reddy

2012-03-01

Toluene diisocyanates (2,4-TDI and 2,6-TDI) are important intermediates in the chemical industry. Among the main damages after low levels of TDI exposure are lung sensitization and asthma. It is therefore necessary to have sensitive and specific methods to monitor isocyanate exposure of workers. Urinary metabolites or protein adducts have been used as biomarkers in workers exposed to TDI. However, with these methods it was not possible to determine if the biomarkers result from exposure to TDI or to the corresponding toluene diamines (TDA). This work presents a new procedure for the determination of isocyanate-specific albumin adducts. Isotope dilution mass spectrometry was used to measure the adducts in albumin present in workers exposed to TDI. 2,4-TDI and 2,6-TDI formed adducts with lysine: N(ϵ)-[({3-amino-4-methylphenyl}amino)carbonyl]-lysine, N(ϵ)-[({5-amino-2-methylphenyl}amino)carbonyl]-lysine, and N(ϵ)- [({3-amino-2-methylphenyl}amino)carbonyl]-lysine. In future studies, this new method can be applied to measure TDI-exposures in workers.

Incidence of cancer and exposure to toluene diisocyanate and methylene diphenyldiisocyanate: a cohort based case-referent study in the polyurethane foam manufacturing industry.

PubMed Central

Hagmar, L; Strömberg, U; Welinder, H; Mikoczy, Z

1993-01-01

OBJECTIVE--To assess the association between occupational exposure to toluene diisocyanate or methylene diphenyldiisocyanate and risk of cancer. DESIGN--A cohort based case-referent study. STUDY BASE--7023 subjects employed during the period 1958 to 1987 in nine Swedish polyurethane foam manufacturing plants. MAIN OUTCOME MEASURES--Odds ratios adjusted with respect to the matching factors (age at risk, calendar year at risk, sex, and plant), calculated from the conditional logistic regression model. RESULTS--A non-significant association was found between high exposure to isocyanates and prostate cancer (OR 2.66, 90% confidence interval (90% CI) 0.39-18.1), which was not enhanced when an induction latency period of 10 years was applied. An association between isocyanate exposure and colon cancer was even weaker. No associations were seen for non-Hodgkin's lymphoma and rectal cancer. CONCLUSIONS--The tentative associations, derived from a previous cohort study, between isocyanate exposure and excess risk for non-Hodgkin's lymphoma and rectal cancer were not supported. Instead, non-significant associations with prostate cancer, and possibly colon cancer, were seen. PMID:8280625

Melt electrospinning of biodegradable polyurethane scaffolds

PubMed Central

Karchin, Ari; Simonovsky, Felix I.; Ratner, Buddy D.; Sanders, Joan E.

2014-01-01

Electrospinning from the melt, in contrast to from solution, is an attractive tissue engineering scaffold manufacturing process as it allows for the formation of small diameter fibers while eliminating potentially cytotoxic solvents. Despite this, there is a dearth of literature on scaffold formation via melt electrospinning. This is likely due to the technical challenges related to the need for a well-controlled high temperature setup and the difficulty in developing an appropriate polymer. In this paper, a biodegradable and thermally stable polyurethane (PU) is described specifically for use in melt electrospinning. Polymer formulations of aliphatic PUs based on (CH2)4-content diisocyanates, polycaprolactone (PCL), 1,4-butanediamine and 1,4-butanediol (BD) were evaluated for utility in the melt electrospinning process. The final polymer formulation, a catalyst-purified PU based on 1,4-butane diisocyanate, PCL and BD in a 4/1/3 molar ratio with a weight-average molecular weight of about 40 kDa, yielded a nontoxic polymer that could be readily electrospun from the melt. Scaffolds electrospun from this polymer contained point bonds between fibers and mechanical properties analogous to many in vivo soft tissues. PMID:21640853

Tunable polymeric sorbent materials for fractionation of model naphthenates.

PubMed

Mohamed, Mohamed H; Wilson, Lee D; Headley, John V

2013-04-04

The sorption properties are reported for several examples of single-component carboxylic acids representing naphthenic acids (NAs) with β-cyclodextrin (β-CD) based polyurethane sorbents. Seven single-component examples of NAs were chosen with variable z values, carbon number, and chemical structure as follows: 2-hexyldecanoic acid (z = 0 and C = 16; S1), n-caprylic acid (z = 0 and C = 8; S2), trans-4-pentylcyclohexanecarboxylic acid (z = -2 and C = 12; S3), 4-methylcyclohexanecarboxylic acid (z = -2 and C = 8; S4), dicyclohexylacetic acid (z = -4; C = 14; S5), 4-pentylbicyclo[2.2.2]octane-1-carboxylic acid (z = -4; C = 14; S6), and lithocholic acid (z = -6; C = 24; S7). The copolymer sorbents were synthesized at three relative β-CD:diisocyanate mole ratios (i.e., 1:1, 1:2, and 1:3) using 4,4'-dicyclohexylmethane diisocyanate (CDI) and 4,4'-diphenylmethane diisocyanate (MDI). The sorption properties of the copolymer sorbents were characterized using equilibrium sorption isotherms in aqueous solution at pH 9.00 with electrospray ionization mass spectrometry. The equilibrium fraction of the unbound carboxylate anions was monitored in the aqueous phase. The sorption properties of the copolymer sorbents (i.e., Qm) were obtained from the Sips isotherm model. The Qm values generally decrease as the number of accessible β-CD inclusion sites in the copolymer framework decreases. The chemical structure of the adsorbates played an important role in their relative uptake, as evidenced by the adsorbate lipophilic surface area (LSA) and the involvement of hydrophobic effects. The copolymers exhibit molecular selective sorption of the single-component carboxylates in mixtures which suggests their application as sorbents for fractionation of mixtures of NAs. By comparison, granular activated carbon (GAC) and chitosan sorbents did not exhibit any significant molecular selective sorption relative to the copolymer materials; however, evidence of variable sorption capacity was observed among the sorbents investigated.

China on the Mekong: Legitimacy Imperatives and Policy Case Studies

DTIC Science & Technology

2013-12-01

1  B.  IMPORTANCE ................................................................................................1  C.  PROBLEMS...gross domestic product GMS Greater Mekong Subregion HDI human development indicators MRC Mekong River Commission MOU memoranda of understanding MPS...home affect China’s policies along the Mekong River? B. IMPORTANCE A careful investigation of PRC policies on the Mekong River will contribute to a

Education, Human Development and Quality of Life: Measurement Issues and Implications for India

ERIC Educational Resources Information Center

Narayana, M. R.

2009-01-01

This paper analyses and compares the measurement of indicators and variables in the construction of education index in Human Development Index (HDI) at the global, national and 18 sub-national human development reports in India since 1990. The results show non-comparability of measurement of the education indicators and variables. This implies…

Housing Quality and Access to Material and Learning Resources within the Home Environment in Developing Countries

ERIC Educational Resources Information Center

Bradley, Robert H.; Putnick, Diane L.

2012-01-01

This study examined home environment conditions (housing quality, material resources, formal and informal learning materials) and their relations with the Human Development Index (HDI) in 28 developing countries. Home environment conditions in these countries varied widely. The quality of housing and availability of material resources at home were…

77 FR 30855 - Sixty-Ninth Report of the TSCA Interagency Testing Committee to the Administrator of the...

Federal Register 2010, 2011, 2012, 2013, 2014

2012-05-23

... diisocyanates can cause contact dermatitis, skin and respiratory tract irritation, immune sensitization, and... identity or contact information unless you provide it in the body of your comment. If you send an email... Internet. If you submit an electronic comment, EPA recommends that you include your name and other contact...

Site-selective modification of cellulose nanocrystals with isophorone diisocyanate and formation of polyurethane-CNC composites

Treesearch

Natalie M. Girouard; Shanhong Xu; Gregory T. Schueneman; Meisha L. Shofner; J. Carson Meredith

2016-01-01

The unequal reactivity of the two isocyanate groups in an isophorone diisocyante (IPDI) monomer was exploited to yield modified cellulose nanocrystals (CNCs) with both urethane and isocyanate functionality. The chemical functionality of the modified CNCs was verified with ATR-FTIR analysis and elemental analysis. The selectivity for the secondary isocyanate group using...

Chemical and physical interpretation of MDI cure in saturated steam environments

Treesearch

David Harper; Michael P. Wolcott; Timothy Rials

1999-01-01

The cure of polymeric 4-4? diphenylmethane diisocyanate, PMDl, in wood composite manufacturing has been the subject of much research. The exact contribution of polyurethane, polyurea, and polyurete formation to PMDI/wood bonding is still debated. This study foregoes the mechanism controversy and studies the cure from a panel consolidation process. Micro-dielectric...

40 CFR 721.10581 - Brominated polyurethane prepolymers of methylene diphenyl diisocyanate (MDI) (generic).

Code of Federal Regulations, 2014 CFR

2014-07-01

..., tight-fitting half-face respirator equipped with N100 (if oil aerosols absent), R100, or P100 filters. (B) NIOSH-certified air-purifying, tight-fitting full-face respirator equipped with N100 (if oil...-certified powered air-purifying respirator equipped with a tight-fitting facepiece (either half-face or full...

Nothing about Us without Us: Asking Kentuckians with Disabilities about What They Need to Thrive. Research Brief. Spring 2016

ERIC Educational Resources Information Center

Mevoli, K.; Tanner, A.; Adams, C.; Rhodes, A.; Warren, T.; Sherif, V.

2016-01-01

As a part of their strategic long term planning process, the Commonwealth Council for Developmental Disabilities (CCDD), Kentucky Protection & Advocacy (KPA), and the Human Development Institute (HDI) at the University of Kentucky developed a survey to identify areas of high need for people with disabilities in the state. This research brief…

Subjective and Objective Evaluation of Pitch Extractors for LPC and Harmonic Deviations Vocoders.

DTIC Science & Technology

1984-07-01

Neman Inc. significance of the voicing errors at unvoiced-voiced transitions (see Section 7.2), is to penalize the early and the late start of...8217- Report No. 5726 Bolt Beranek and Neman Inc. Objective PAL Measure LPC/Cler =/Clear LPC/Noise HDY Noise S- Bes Measures: S EDFL-C-EF -0.990 -0.991 -0.995

Higher Education Academics' Satisfaction with Their Terms and Conditions of Service and Their Job Satisfaction: A Case Study

ERIC Educational Resources Information Center

Mammen, K. J.

2006-01-01

This article originates from a research conducted at a Historically Disadvantaged Institution (HDI) in South Africa. Academics (those who teach) at higher education institutions (HEIs) are usually highly qualified personnel. Their satisfaction with the terms and conditions of service and the job satisfaction they derive from and through their work…

Indonesian Perspective on Massive Open Online Courses: Opportunities and Challenges

ERIC Educational Resources Information Center

Berliyanto; Santoso, Harry B.

2018-01-01

There are two indications that Indonesia needs to improve its education quality. The first is the Human Development Index (HDI), which is still at the medium level, and the second is the enrollment rate in higher education, which is also at the low level. MOOCs have the potential to solve both problems. However, implementing MOOCs in a developing…

Patterns of Human Development Indicators across Constitutional Analysis of Children's Rights to Protection, Provision, and Participation

ERIC Educational Resources Information Center

Habashi, Janette; Wright, Lynne; Hathcoat, John D.

2012-01-01

This study examines children's images in constitutions and/or amendments as articulated in the Convention on the Rights of the Child while they intersect with the three dimensions of the Human Development Index (HDI) of 2008: life expectancy, educational index, and GDP. The connection between the images of the child and the fulfillment of the…

Employing the Components of the Human Development Index to Drive Resources to Educational Policies

ERIC Educational Resources Information Center

Sant'Anna, Annibal Parracho; de Araujo Ribeiro, Rodrigo Otavio; Dutt-Ross, Steven

2011-01-01

A new form of composition of the indicators employed to generate the United Nations Human Development Index (HDI) is presented here. This form of composition is based on the assumption that random errors affect the measurement of each indicator. This assumption allows for replacing the vector of evaluations according to each indicator by vectors…

Attracting Attention for the Cause. The Reporting of Three Indices in the UK National Press

ERIC Educational Resources Information Center

Morse, Stephen

2011-01-01

Indicators and indices (a collection of indicators into a single value) have been promoted for some time as convenient devices for the presentation of complex datasets to a more general audience. Examples of indices are the corruption perception index (CPI), human development index (HDI) and ecological footprint (EF). The research reported in this…

Another Approach to Measuring Human Development: The Composite Dynamic Human Development Index

ERIC Educational Resources Information Center

Bilbao-Ubillos, Javier

2013-01-01

This paper seeks mainly to contribute to the debate on how the relative degree of development of a country should be measured by proposing an indicator to build on the valuable starting point provided by the Human Development Index (HDI). The indicator proposed is called the "Composite, Dynamic Human Development Index". It incorporates in a simple…

Effects on well-being of investing in cleaner air in India.

PubMed

Sanderson, Warren; Striessnig, Erich; Schöpp, Wolfgang; Amann, Markus

2013-01-01

Over the past decade, India has experienced rapid economic growth along with increases in levels of air pollution. Our goal is to examine how alternative policies for air pollution abatement affect well-being there. In particular, we estimate the effects of policies to reduce the levels of ambient fine particulates (PM2.5), which are especially harmful to human health, on well-being, quantified using the United Nations' human development index (HDI). Two of the three dimensions of this index are based on gross domestic product (GDP) per capita and life expectancy. Our approach allows reductions in PM2.5 to affect both of them. In particular, economic growth is affected negatively through the costs of the additional pollution control measures and positively through the increased productivity of the population. We consider three scenarios of PM2.5 abatement, corresponding to no further control, current Indian legislation, and current European legislation. The overall effect in both control scenarios is that growth in GDP is virtually unaffected relative to the case of no further controls, life expectancy is higher, and well-being, as measured by the HDI, is improved. In India, air pollution abatement investments clearly improve well-being.

Dynamic stability and slider-lubricant interactions in hard disk drives

NASA Astrophysics Data System (ADS)

Ambekar, Rohit Pradeep

2007-12-01

Hard disk drives (HDD) have played a significant role in the current information age and have become the backbone of storage. The soaring demand for mass data storage drives the necessity for increasing capacity of the drives and hence the areal density on the disks as well as the reliability of the HDD. To achieve greater areal density in hard disk drives, the flying height of the airbearing slider continually decreases. Different proximity forces and interactions influence the air bearing slider resulting in fly height modulation and instability. This poses several challenges to increasing the areal density (current goal is 2Tb/in.2) as well as making the head-disk interface (HDI) more reliable. Identifying and characterizing these forces or interactions has become important for achieving a stable fly height at proximity and realizing the goals of areal density and reliability. Several proximity forces or interactions influencing the slider are identified through the study of touchdown-takeoff hysteresis. Slider-lubricant interaction which causes meniscus force between the slider and disk as well as airbearing surface contamination seems to be the most important factor affecting stability and reliability at proximity. In addition, intermolecular forces and disk topography are identified as important factors. Disk-to-slider lubricant transfer leads to lubricant pickup on the slider and also causes depletion of lubricant on the disk, affecting stability and reliability of the HDI. Experimental and numerical investigation as well as a parametric study of the process of lubricant transfer has been done using a half-delubed disk. In the first part of this parametric study, dependence on the disk lubricant thickness, lubricant type and slider ABS design has been investigated. It is concluded that the lubricant transfer can occur without slider-disk contact and there can be more than one timescale associated with the transfer. Further, the transfer increases non-linearly with increasing disk lubricant thickness. Also, the transfer depends on the type of lubricant used, and is less for Ztetraol than for Zdol. The slider ABS design also plays an important role, and a few suggestions are made to improve the ABS design for better lubricant performance. In the second part of the parametric study, the effect of carbon overcoat, lubricant molecular weight and inclusion of X-1P and A20H on the slider-lubricant interactions is investigated using a half-delubed disk approach. Based on the results, it is concluded that there exists a critical head-disk clearance above which there is negligible slider-lubricant interaction. The interaction starts at this critical clearance and increases in intensity as the head-disk clearance is further decreased below the critical clearance. Using shear stress simulations and previously published work a theory is developed to support the experimental observations. The critical clearance depends on various HDI parameters and hence can be reduced through proper design of the interface. Comparison of critical clearance on CHx and CHxNy media indicates that presence of nitrogen is better for HDI as it reduces the critical clearance, which is found to increase with increasing lubricant molecular weight and in presence of additives X-1P and A20H. Further experiments maintaining a fixed slider-disk clearance suggest that two different mechanisms dominate the disk-to-slider and slider-to-disk lubricant transfer. One of the key factors influencing the slider stability at proximity is the disk topography, since it provides dynamic excitation to the low-flying sliders and strongly influences its dynamics. The effect of circumferential as well as radial disk topography is investigated using a new method to measure the 2-D (true) disk topography. Simulations using CMLAir dynamic simulator indicate a strong dependence on the circumferential roughness and waviness features as well as radial features, which have not been studied intensively till now. The simulations with 2-D disk topography are viewed as more realistic than the 1-D simulations. Further, it is also seen that the effect of the radial features can be reduced through effective ABS design. Finally, an attempt has been made to establish correlations between some of the proximity interactions as well as others which may affect the HDI reliability by creating a relational chart. Such an organization serves to give a bigger picture of the various efforts being made in the field of HDI reliability and link them together. From this chart, a causal relationship is suggested between the electrostatic, intermolecular and meniscus forces.

Evaluation of the cure kinetics of the wood/pMDI bondline

Treesearch

David P. Harper; Michael P. Wolcott; Timothy G. Rials

2001-01-01

Micro-dielectric analysis (µDEA) and differentia1 scanning calorimetry (DSC) were used to monitor cure of polymeric diphenyl-methane diisocyanate (pMDI) resin with wood strands in a saturated steam environment. A first-order autocatalyzed kinetic model was employed to determine kinetic parameters. The kinetics were found to follow an Arrhenius relation. A single ramp...

Opportunities and obstacles in translating evidence to policy in occupational asthma.

PubMed

Tarlo, Susan M; Arif, Ahmed A; Delclos, George L; Henneberger, Paul; Patel, Jenil

2018-06-01

Occupational asthma (OA), a common respiratory disorder in Western countries, is caused by exposures at the workplace. It is part of a broader definition of work-related asthma (WRA) that also includes pre-existing asthma aggravated by substances present in the workplace environment, and it is potentially preventable. The purpose of this paper is to illustrate preventive measures for occupational asthma by case studies. In three case studies we discuss preventive measures that have been associated with reductions in incidence of occupational asthma from natural rubber latex and from diisocyanates as supported by published literature. We also discuss challenges in relation to asthma from cleaning products in healthcare work. Several preventive measures have been associated with reduction in incidence of occupational asthma from natural rubber latex and from diisocyanates, and may provide lessons for prevention of other causes of occupational asthma. Cleaning products remain an unresolved problem at present with respect to asthma risks but potential measures include the use of safer products and safer applications such as avoidance of spray products, use of occupational hygiene methods such as improving local ventilation, and when appropriate, the use of personal protective devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Opportunities and obstacles in translating evidence to policy in occupational asthma

PubMed Central

Tarlo, Susan M.; Arif, Ahmed A.; Delclos, George L.; Henneberger, Paul; Patel, Jenil

2018-01-01

Purpose Occupational asthma (OA), a common respiratory disorder in Western countries, is caused by exposures at the workplace. It is part of a broader definition of work-related asthma (WRA) that also includes pre-existing asthma aggravated by substances present in the workplace environment, and it is potentially preventable. The purpose of this paper is to illustrate preventive measures for occupational asthma by case studies. Methods In three case studies we discuss preventive measures that have been associated with reductions in incidence of occupational asthma from natural rubber latex and from diisocyanates as supported by published literature. We also discuss challenges in relation to asthma from cleaning products in healthcare work. Results and conclusions Several preventive measures have been associated with reduction in incidence of occupational asthma from natural rubber latex and from diisocyanates, and may provide lessons for prevention of other causes of occupational asthma. Cleaning products remain an unresolved problem at present with respect to asthma risks but potential measures include the use of safer products and safer applications such as avoidance of spray products, use of occupational hygiene methods such as improving local ventilation, and when appropriate, the use of personal protective devices. PMID:28434545

Development of modified poly(perfluoropropyleneoxide) urethane systems for use in liquid oxygen and in enriched 100 percent oxygen atmosphere

NASA Technical Reports Server (NTRS)

Harrison, E. S.

1973-01-01

This program consisted of two separate though related phases. The initial phase was directed toward improving the mechanical and adhesive properties of the very highly fluorinated-polyurethane resin system derived from the hydroxyl-terminated polyperfluoropropylene oxide and 6-chloro-2,4,5-trifluoro-m-phenylene diisocyanate. Various new curing agents for this system were investigated, with the goal of providing a more thermally stable crosslink (cure) mechanism to provide wider applicability and fuller utilization of the outstanding oxygen resistance of the PFPO system. Complete resistance to liquid- and gaseous-oxygen impact at presures as high as 1035 N/sq cm were attained with the use of the PFPO resin castings. The second corollary phase was directed toward investigating the feasibility and optimization of the allophanate cured, urethane extended polymer derived from hydroxyl-terminated polyperfluoropropyleneoxide and 6-chloro-2,4,5-trifluoro-m-phenylene diisocyanate, as the adhesive system for use in a weld-bond configuration for liquid oxygen tankage. The synthesis and application procedures of the adhesive system to insure liquid oxygen compatibility (under 10 kg-m loading), and the development of procedures and techniques to provide high quality weld-bonded joint configurations were studied.

Toluene diisocyanate increases airway responsiveness to substance P and decreases airway neutral endopeptidase.

PubMed

Sheppard, D; Thompson, J E; Scypinski, L; Dusser, D; Nadel, J A; Borson, D B

1988-04-01

Substance P and related tachykinins contribute to the airway hyperresponsiveness caused by toluene diisocyanate (TDI) in guinea pigs. Neutral endopeptidase (NEP) is an important modulator of substance P-induced responses. To test the hypothesis that exposure to TDI would increase responsiveness to substance P by inhibiting activity of this enzyme, we determined the dose of substance P required to increase pulmonary resistance by 200% above baseline (PD200) before and after administration of the pharmacologic inhibitor phosphoramidon in guinea pigs studied 1 h after a 1-h exposure to air or 3 ppm TDI. TDI exposure increased responsiveness to substance P significantly. However, phosphoramidon caused a significantly greater leftward shift of the substance P dose-response curve in air-exposed animals than it did in TDI-exposed animals, so that after phosphoramidon, mean values of PD200 in animals exposed to air or TDI did not differ. Tracheal NEP activity was significantly less after exposure to TDI than after exposure to air, whereas activity in the esophagus was the same in both groups. These results suggest that TDI exposure increases the bronchoconstrictor responsiveness of guinea pigs to substance P, in large part through inhibition of airway NEP.

Toluene diisocyanate increases airway responsiveness to substance P and decreases airway neutral endopeptidase.

PubMed Central

Sheppard, D; Thompson, J E; Scypinski, L; Dusser, D; Nadel, J A; Borson, D B

1988-01-01

Substance P and related tachykinins contribute to the airway hyperresponsiveness caused by toluene diisocyanate (TDI) in guinea pigs. Neutral endopeptidase (NEP) is an important modulator of substance P-induced responses. To test the hypothesis that exposure to TDI would increase responsiveness to substance P by inhibiting activity of this enzyme, we determined the dose of substance P required to increase pulmonary resistance by 200% above baseline (PD200) before and after administration of the pharmacologic inhibitor phosphoramidon in guinea pigs studied 1 h after a 1-h exposure to air or 3 ppm TDI. TDI exposure increased responsiveness to substance P significantly. However, phosphoramidon caused a significantly greater leftward shift of the substance P dose-response curve in air-exposed animals than it did in TDI-exposed animals, so that after phosphoramidon, mean values of PD200 in animals exposed to air or TDI did not differ. Tracheal NEP activity was significantly less after exposure to TDI than after exposure to air, whereas activity in the esophagus was the same in both groups. These results suggest that TDI exposure increases the bronchoconstrictor responsiveness of guinea pigs to substance P, in large part through inhibition of airway NEP. PMID:2450892

Two cases of paraoccupational asthma due to toluene diisocyanate (TDI).

PubMed

De Zotti, R; Muran, A; Zambon, F

2000-12-01

Two cases of paraoccupational asthma caused by toluene diisocyanate (TDI) are reported. The first patient was a metal worker in a machine shop situated near a factory producing polyurethane foam. Symptoms at work were not explainable by any specific exposure to irritants or allergens in the work site. As the patient recalled previous occasional work in the adjacent polyurethane factory with accompanying worsening of respiratory symptoms, a specific inhalation (SIC) test was performed with TDI, which confirmed the diagnosis of TDI asthma. The second case was a woman working part time as a secretary in the offices of her son's factory for varnishing wooden chairs. TDI was present in the products used in the varnishing shed. The SIC test confirmed the diagnosis of TDI asthma, despite the fact that the patient's job did not present risk of exposure to the substance. In both patients, symptoms disappeared when further exposure was avoided. These two cases confirm that paraoccupational exposure to TDI must be considered when evaluating patients with asthma not mediated by immunoglobulin E. They also suggest the need for more prospective studies evaluating the health risk for the general population living near polyurethane factories or other firms that use TDI.

Gelatin-based Hydrogel Degradation and Tissue Interaction in vivo: Insights from Multimodal Preclinical Imaging in Immunocompetent Nude Mice.

PubMed

Tondera, Christoph; Hauser, Sandra; Krüger-Genge, Anne; Jung, Friedrich; Neffe, Axel T; Lendlein, Andreas; Klopfleisch, Robert; Steinbach, Jörg; Neuber, Christin; Pietzsch, Jens

2016-01-01

Hydrogels based on gelatin have evolved as promising multifunctional biomaterials. Gelatin is crosslinked with lysine diisocyanate ethyl ester (LDI) and the molar ratio of gelatin and LDI in the starting material mixture determines elastic properties of the resulting hydrogel. In order to investigate the clinical potential of these biopolymers, hydrogels with different ratios of gelatin and diisocyanate (3-fold (G10_LNCO3) and 8-fold (G10_LNCO8) molar excess of isocyanate groups) were subcutaneously implanted in mice (uni- or bilateral implantation). Degradation and biomaterial-tissue-interaction were investigated in vivo (MRI, optical imaging, PET) and ex vivo (autoradiography, histology, serum analysis). Multimodal imaging revealed that the number of covalent net points correlates well with degradation time, which allows for targeted modification of hydrogels based on properties of the tissue to be replaced. Importantly, the degradation time was also dependent on the number of implants per animal. Despite local mechanisms of tissue remodeling no adverse tissue responses could be observed neither locally nor systemically. Finally, this preclinical investigation in immunocompetent mice clearly demonstrated a complete restoration of the original healthy tissue.

RARE PROJECT: QUANTIFYING THE IMPACT OF AN AUTOBODY SHOP COMPLIANCE ASSISTANCE PROGRAM IN LAWRENCE, MA ON SHOP EMISSIONS AND RESIDENTIAL EXPOSURES TO HDI AND OTHER ISOCYANTES

EPA Science Inventory

This is an ORD Regional Applied Research Effort (RARE) study with EPA Region 1. For the past several years Region 1 has been managing an EPA grant for an auto body shop compliance assistance project in Lawrence, MA to address residents' concerns about auto body shops as a source...

Mortality of emergency abdominal surgery in high-, middle- and low-income countries.

PubMed

2016-07-01

Surgical mortality data are collected routinely in high-income countries, yet virtually no low- or middle-income countries have outcome surveillance in place. The aim was prospectively to collect worldwide mortality data following emergency abdominal surgery, comparing findings across countries with a low, middle or high Human Development Index (HDI). This was a prospective, multicentre, cohort study. Self-selected hospitals performing emergency surgery submitted prespecified data for consecutive patients from at least one 2-week interval during July to December 2014. Postoperative mortality was analysed by hierarchical multivariable logistic regression. Data were obtained for 10 745 patients from 357 centres in 58 countries; 6538 were from high-, 2889 from middle- and 1318 from low-HDI settings. The overall mortality rate was 1·6 per cent at 24 h (high 1·1 per cent, middle 1·9 per cent, low 3·4 per cent; P < 0·001), increasing to 5·4 per cent by 30 days (high 4·5 per cent, middle 6·0 per cent, low 8·6 per cent; P < 0·001). Of the 578 patients who died, 404 (69·9 per cent) did so between 24 h and 30 days following surgery (high 74·2 per cent, middle 68·8 per cent, low 60·5 per cent). After adjustment, 30-day mortality remained higher in middle-income (odds ratio (OR) 2·78, 95 per cent c.i. 1·84 to 4·20) and low-income (OR 2·97, 1·84 to 4·81) countries. Surgical safety checklist use was less frequent in low- and middle-income countries, but when used was associated with reduced mortality at 30 days. Mortality is three times higher in low- compared with high-HDI countries even when adjusted for prognostic factors. Patient safety factors may have an important role. NCT02179112 (http://www.clinicaltrials.gov). © 2016 BJS Society Ltd Published by John Wiley & Sons Ltd.

Social Context and Dental Pain in Adults of Colombian Ethnic Minority Groups: A Multilevel Cross-Sectional Study.

PubMed

Ardila, Carlos M; Agudelo-Suárez, Andrés A

2016-01-01

To estimate the effect of social context on dental pain in adults of Colombian ethnic minority groups (CEGs). Information from 34,843 participants was used. A multilevel model was constructed that had ethnic groups (ie, CEGs and non-CEGs) at level 1 and Colombian states at level 2. Contextual variables included gross domestic product (GDP), Human Development Index (HDI), and Unmet Basic Needs Index (UBNI). Dental pain was observed in 12.3% of 6,440 CEGs. In an unadjusted logistic regression model, dental pain was associated with being a CEG (odds ratio [95% confidence interval], 1.34 [1.22-1.46]; P = .0001). This association remained significant after adjusting for possible confounding variables. An unconditional multilevel analysis showed that the variance in dental pain was statistically significant at the ethnic group level (β = 0.047 ± 0.015; P = .0009) and at the state level (β = 0.038 ± 0.019; P = .02) and that the variation between ethnic groups was higher than the variation between states (55% vs 45%, respectively). In a multivariate model, the variance in dental pain was also statistically significant at the ethnic group level (β = 0.029 ± 0.012; P = .007) and the state level (β = 0.042 ± .019; P = .01), but the variation between states was higher (40% vs 60%). The results of multilevel multivariate analyses showed that dental pain was associated with increasing age (β = 0.009 ± 0.001; P = .0001), lower education level (β = 0.302 ± 0.103; P = .0001), female sex (β = 0.031 ± 0.069; P = .003), GDP (β = 5.136 ± 2.009; P = .002) and HDI (β = 6.862 ± 5.550; P = .004); however, UBNI was not associated with dental pain. The variance in dental pain was higher between states than between ethnic groups in the multivariate multilevel model. Dental pain in CEGs was associated with contextual and individual factors. Considering contextual factors, GDP and HDI may play a major role in dental pain prevalence.

Identifying biomarkers of dietary patterns by using metabolomics123

PubMed Central

Derkach, Andriy; Reedy, Jill; Subar, Amy F; Sampson, Joshua N; Albanes, Demetrius; Gu, Fangyi; Kontto, Jukka; Lassale, Camille; Liao, Linda M; Männistö, Satu; Mondul, Alison M; Weinstein, Stephanie J; Irwin, Melinda L; Mayne, Susan T; Stolzenberg-Solomon, Rachael

2017-01-01

Background: Healthy dietary patterns that conform to national dietary guidelines are related to lower chronic disease incidence and longer life span. However, the precise mechanisms involved are unclear. Identifying biomarkers of dietary patterns may provide tools to validate diet quality measurement and determine underlying metabolic pathways influenced by diet quality. Objective: The objective of this study was to examine the correlation of 4 diet quality indexes [the Healthy Eating Index (HEI) 2010, the Alternate Mediterranean Diet Score (aMED), the WHO Healthy Diet Indicator (HDI), and the Baltic Sea Diet (BSD)] with serum metabolites. Design: We evaluated dietary patterns and metabolites in male Finnish smokers (n = 1336) from 5 nested case-control studies within the Alpha-Tocopherol, Beta-Carotene Cancer Prevention Study cohort. Participants completed a validated food-frequency questionnaire and provided a fasting serum sample before study randomization (1985–1988). Metabolites were measured with the use of mass spectrometry. We analyzed cross-sectional partial correlations of 1316 metabolites with 4 diet quality indexes, adjusting for age, body mass index, smoking, energy intake, education, and physical activity. We pooled estimates across studies with the use of fixed-effects meta-analysis with Bonferroni correction for multiple comparisons, and conducted metabolic pathway analyses. Results: The HEI-2010, aMED, HDI, and BSD were associated with 23, 46, 23, and 33 metabolites, respectively (17, 21, 11, and 10 metabolites, respectively, were chemically identified; r-range: −0.30 to 0.20; P = 6 × 10−15 to 8 × 10−6). Food-based diet indexes (HEI-2010, aMED, and BSD) were associated with metabolites correlated with most components used to score adherence (e.g., fruit, vegetables, whole grains, fish, and unsaturated fat). HDI correlated with metabolites related to polyunsaturated fat and fiber components, but not other macro- or micronutrients (e.g., percentages of protein and cholesterol). The lysolipid and food and plant xenobiotic pathways were most strongly associated with diet quality. Conclusions: Diet quality, measured by healthy diet indexes, is associated with serum metabolites, with the specific metabolite profile of each diet index related to the diet components used to score adherence. This trial was registered at clinicaltrials.gov as NCT00342992. PMID:28031192

Three-dimensional and thermal surface imaging produces reliable measures of joint shape and temperature: a potential tool for quantifying arthritis

PubMed Central

Spalding, Steven J; Kwoh, C Kent; Boudreau, Robert; Enama, Joseph; Lunich, Julie; Huber, Daniel; Denes, Louis; Hirsch, Raphael

2008-01-01

Introduction The assessment of joints with active arthritis is a core component of widely used outcome measures. However, substantial variability exists within and across examiners in assessment of these active joint counts. Swelling and temperature changes, two qualities estimated during active joint counts, are amenable to quantification using noncontact digital imaging technologies. We sought to explore the ability of three dimensional (3D) and thermal imaging to reliably measure joint shape and temperature. Methods A Minolta 910 Vivid non-contact 3D laser scanner and a Meditherm med2000 Pro Infrared camera were used to create digital representations of wrist and metacarpalphalangeal (MCP) joints. Specialized software generated 3 quantitative measures for each joint region: 1) Volume; 2) Surface Distribution Index (SDI), a marker of joint shape representing the standard deviation of vertical distances from points on the skin surface to a fixed reference plane; 3) Heat Distribution Index (HDI), representing the standard error of temperatures. Seven wrists and 6 MCP regions from 5 subjects with arthritis were used to develop and validate 3D image acquisition and processing techniques. HDI values from 18 wrist and 9 MCP regions were obtained from 17 patients with active arthritis and compared to data from 10 wrist and MCP regions from 5 controls. Standard deviation (SD), coefficient of variation (CV), and intraclass correlation coefficients (ICC) were calculated for each quantitative measure to establish their reliability. CVs for volume and SDI were <1.3% and ICCs were greater than 0.99. Results Thermal measures were less reliable than 3D measures. However, significant differences were observed between control and arthritis HDI values. Two case studies of arthritic joints demonstrated quantifiable changes in swelling and temperature corresponding with changes in symptoms and physical exam findings. Conclusion 3D and thermal imaging provide reliable measures of joint volume, shape, and thermal patterns. Further refinement may lead to the use of these technologies to improve the assessment of disease activity in arthritis. PMID:18215307

Dominance and leadership in research activities: Collaboration between countries of differing human development is reflected through authorship order and designation as corresponding authors in scientific publications

PubMed Central

Park, Jinseo; Huamaní, Charles; Ramos, José M.

2017-01-01

Introduction Scientific collaboration is an important mechanism that enables the integration of the least developed countries into research activities. In the present study, we use the order of author signatures and addresses for correspondence in scientific publications as variables to analyze the interactions between countries of very high (VHHD), high (HHD), medium (MHD), and low human development (LHD). Methodology We identified all documents published between 2011 and 2015 in journals included in the Science Citation Index-Expanded categories’ of Tropical Medicine, Infectious Diseases, Parasitology, and Pediatrics. We then classified the countries participating in the publications according to their Human Development Index (HDI), analyzing the international collaboration; positioning and influence of some countries over others in cooperative networks; their leadership; and the impact of the work based on the HDI and the type of collaboration. Results We observed a high degree of international collaboration in all the areas analyzed, in the case of both LHD and MHD countries. We identified numerous cooperative links between VHHD countries and MHD/LHD countries, reflecting the fact that cooperative links are an important mechanism for integrating research activities into the latter. The countries with large emerging economies, such as Brazil and China stand out due to the dominance they exert in the collaborations established with the United States, the UK, and other European countries. The analysis of the leadership role of the countries, measured by the frequency of lead authorships, shows limited participation by MHD/LHD countries. This reduced participation among less developed countries is further accentuated by their limited presence in the addresses for correspondence. We observed significant statistical differences in the degree of citation according to the HDI of the participating countries. Conclusions The order of signatures and the address for correspondence in scientific publications are bibliographic characteristics that facilitate a precise, in-depth analysis of cooperative practices and their associations with concepts like dominance or leadership. This is useful to monitor the existing balance in research participation in health research publications. PMID:28792519

Polyfibroblast Phase 4: A Self-Healing and Galvanic Protection Additive

DTIC Science & Technology

2014-11-26

scratches. Designed to work with existing military grade primers, Polyfibroblast consists of microscopic, hollow zinc tubes filled with a moisture...barrier layer if corrosion commences before its self-assembly completes. Once the OTS passivation layer has formed, however, it forms an insulating ...silica nanopowder (10-20 nm diameter) replaces the conventional surfactant or hydrocolloid emulsifier. Isophorone diisocyanate (IPDI) in the OTS core

Production of high molecular weight polylactic acid

DOEpatents

Bonsignore, Patrick V.

1995-01-01

A degradable high molecular weight poly(lactic acid). A poly(lactic acid) has a terminal end group of one of carboxyl or hydroxyl groups with low molecular weight poly(lactic acid) units coupled with linking agents of di-isocyanates, bis-epoxides, bis-oxazolines and bis-ortho esters. The resulting high molecular weight poly(lactic acid) can be used for applications taking advantage of the improved physical properties.

Elucidating How Wood Adhesives Bond to Wood Cell Walls using High-Resolution Solution-State NMR Spectroscopy

Treesearch

Daniel J. Yelle

2013-01-01

Some extensively used wood adhesives, such as pMDI (polymeric methylene diphenyl diisocyanate) and PF (phenol formaldehyde) have shown excellent adhesion properties with wood. However, distinguishing whether the strength is due to physical bonds (i.e., van der Waals, London, or hydrogen bond forces) or covalent bonds between the adherend and the adhesive is not fully...

Highly fluorinated polyurethanes

NASA Technical Reports Server (NTRS)

Stump, E. C., Jr.; Rochow, S. E. (Inventor)

1972-01-01

New polyurethanes containing a high degree of fluorine atoms are reported. The presence of the fluorine atoms in the polyurethane resins provides material having good thermal stability and chemical resistance. These polyurethanes are derived from a new hydroxy-terminated perfluoro polyether. The hydroxy terminated material is reacted with a diisocyanate to produce the polyurethanes. The polyurethanes can be used to form seals, coatings, potting material, hoses and the like.

Delineating pMDI model reactions with loblolly pine via solution-state NMR spectroscopy. Part 1, Catalyzed reactions with wood models and wood polymers

Treesearch

Daniel J. Yelle; John Ralph; Charles R. Frihart

2011-01-01

To better understand adhesive interactions with wood, reactions between model compounds of wood and a model compound of polymeric methylene diphenyl diisocyanate (pMDI) were characterized by solution-state NMR spectroscopy. For comparison, finely ground loblolly pine sapwood, milled-wood lignin and holocellulose from the same wood were isolated and derivatized with...

International Traffic in Arms Regulations (ITAR), (22 CFR 120-130)

DTIC Science & Technology

1996-06-01

Butadienenitrileoxide (BNO); (6) Catocene, N-butyl- ferrocene and other ferrocene derivatives; (7) 3-nitraza-l,5 pentane diisocyanate; (8) Bis(2,2...Tris-l-(2-methyl)aziridinyl phosphine oxide (MAPO), bis(2-methyl aziridinyl) 2-(2-hydroxypropanoxy) propylamino phosphine oxide (BOBBA 8), and...other MAPO derivatives; (22) Bis(2-methyl aziridinyl) methylamino phosphine oxide (methyl BAPO); (23) Organo-metallic coupling agents, specifi

Controlling The Spread of Land-Attack Cruise Missiles.

DTIC Science & Technology

1995-01-01

propellant additives and agents: (1) Bonding agents as follows: (i) tris(l-(2-methyl)aziridinyl) phosphine oxide (MAPO); (ii) trimesoyl-l(2-ethyl...Triphenyl bismuth (TPB) (ii) Isophorone diisocyanate (IPDI) (3) Burning rate modifiers as follows: (i) Catocene (ii) N-butyl- ferrocene (iii...Butacene (iv) Other ferrocene derivatives 9g Controlling the Spread of Land-Attack Cruise Missiles (4) Nitrate esters and nitrato plasticizers as

Is Mauritius Ready to Become the HRD Leader in Africa? An Assessment of Strategic Human Resource Development in Mauritius

ERIC Educational Resources Information Center

Dusoye, Indravidoushi C.; Oogarah, Kavi

2016-01-01

Purpose: This paper aims to explore the applicability of Strategic HRD in Mauritius. Additionally, it assesses if Mauritius, with a high HDI factor, can take the lead on Strategic HRD in Africa. Design/methodology/approach: This paper used a mixed-approach questionnaire. A sample of 21 managers was contacted and received a response rate of 67 per…

The Republic of the Philippines: Background and U.S. Relations

DTIC Science & Technology

2007-08-10

cost of living. 21 The HDI ranks countries according to human development indicators of life expectancy, education, literacy, and gross domestic...sovereignty over Mischief Reef, which is one of approximately 100 reefs and islands disputed by five Southeast Asian countries . A Visiting Forces...Order Code RL33233 The Republic of the Philippines: Background and U.S. Relations Updated August 10, 2007 Thomas Lum Specialist in Asian Affairs

Rebuilding Iraq - The Danish Interagency Strategy

DTIC Science & Technology

2007-02-09

HDI ), Iraq dropped from position number 76 in 1990, to position 126 in 2000. No other country underwent a similar descent in the same period. In the...and mutually impressionable main tendencies in Iraq today: progress in the political process, endeavors to rebuild the country , and a continued...the country , and (3) a continued serious security situation including violent incidents especially in the central part of Iraq but also in other

Worldwide burden of gastric cancer in 2010 attributable to high sodium intake in 1990 and predicted attributable burden for 2030 based on exposures in 2010.

PubMed

Peleteiro, Bárbara; Barros, Susana; Castro, Clara; Ferro, Ana; Morais, Samantha; Lunet, Nuno

2016-08-01

Assessing the impact that patterns of Na intake may have on gastric cancer will provide a more comprehensive estimation of Na reduction as a primary prevention approach. We aimed to estimate the proportion of gastric cancer cases that are attributable to Na intake above the recommendation by the WHO (≤2 g/d) throughout the world in 2010, as well as expected values for 2030. Population attributable fractions (PAF) were computed for 187 countries, using Na intakes in 1990 and 2010 and estimates of the association between Na intake and gastric cancer, assuming a time lag of 20 years. Median PAF ranged from 10·1% in low to 22·5 % in very high Human Development Index (HDI) countries in men (P<0·001) and from 7·2 to 16·6 %, respectively, among women (P<0·001). An increase in median PAF until 2030 is expected in most settings, except for countries classified as low HDI, in both sexes. High Na intakes account for a large proportion of gastric cancer cases, and proportions are expected to increase in almost all of the countries. Intensified efforts to diminish Na intake in virtually all populations are needed to further reduce gastric cancer burden.

Modelling difficulties in abstract thinking in psychosis: the importance of socio-developmental background.

PubMed

Berg, A O; Melle, I; Zuber, V; Simonsen, C; Nerhus, M; Ueland, T; Andreassen, O A; Sundet, K; Vaskinn, A

2017-01-01

Abstract thinking is important in modern understanding of neurocognitive abilities, and a symptom of thought disorder in psychosis. In patients with psychosis, we assessed if socio-developmental background influences abstract thinking, and the association with executive functioning and clinical psychosis symptoms. Participants (n = 174) had a diagnosis of psychotic or bipolar disorder, were 17-65 years, intelligence quotient (IQ) > 70, fluent in a Scandinavian language, and their full primary education in Norway. Immigrants (N = 58) were matched (1:2) with participants without a history of migration (N = 116). All participants completed a neurocognitive and clinical assessment. Socio-developmental background was operationalised as human developmental index (HDI) of country of birth, at year of birth. Structural equation modelling was used to assess the model with best fit. The model with best fit, χ 2  = 96.591, df = 33, p < .001, confirmed a significant indirect effect of HDI scores on abstract thinking through executive functioning, but not through clinical psychosis symptoms. This study found that socio-developmental background influences abstract thinking in psychosis by indirect effect through executive functioning. We should take into account socio-developmental background in the interpretation of neurocognitive performance in patients with psychosis, and prioritise cognitive remediation in treatment of immigrant patients.

Hypervelocity Dust Injection for Plasma Diagnostic Applications

NASA Astrophysics Data System (ADS)

Ticos, Catalin

2005-10-01

Hypervelocity micron-size dust grain injection was proposed for high-temperature magnetized plasma diagnosis. Multiple dust grains are launched simultaneously into high temperature plasmas at several km/s or more. The hypervelocity dust grains are ablated by the electron and ion fluxes. Fast imaging of the resulting luminous plumes attached to each grain is expected to yield local magnetic field vectors. Combination of multiple local magnetic field vectors reproduces 2D or even 3D maps of the internal magnetic field topology. Key features of HDI are: (1) a high spatial resolution, due to a relatively small transverse size of the elongated tail, and (2) a small perturbation level, as the dust grains introduce negligible number of particles compared to the plasma particle inventory. The latter advantage, however, could be seriously compromised if the gas load from the accelerator has an unobstructed access to the diagnosed plasma. Construction of a HDI diagnostic for National Spherical Torus Experiment (NSTX), which includes a coaxial plasma gun for dust grain acceleration, is underway. Hydrogen and deuterium gas discharges inside accelerator are created by a ˜ 1 mF capacitor bank pre-charged up to 10 kV. The diagnostic apparatus also comprises a dust dispenser for pre-loading the accelerator with dust grains, and an imaging system that has a high spatial and temporal resolution.

Properties of Multiphase Polyurethane Systems.

DTIC Science & Technology

1983-07-01

segment - diphenylmethane-diisocyanate/ N - methyldiethanolamine (MDI/ MDEA ). Each polymer was synthesized using a two step reaction technique. The number...OF MULTIPHASE POLYURETHANE SYSTEMS Final Report for Period July 1, 1982-June 30, 1983 Naval Air Systems Command Code 5304 C2 ONavy Contract # N 00019...and COB, UA groups. The existence of 3-dimensional hydrogen bonding (two C-O groups bonded to one N -H group) should shift the COB,UA peak to lower

Production of high molecular weight polylactic acid

DOEpatents

Bonsignore, P.V.

1995-11-28

A degradable high molecular weight poly(lactic acid) is described. The poly(lactic acid) has a terminal end group of one of carboxyl or hydroxyl groups with low molecular weight poly(lactic acid) units coupled with linking agents of di-isocyanates, bis-epoxides, bis-oxazolines and bis-ortho esters. The resulting high molecular weight poly(lactic acid) can be used for applications taking advantage of the improved physical properties.

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2013 CFR

2013-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2012 CFR

2012-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

40 CFR 302.4 - Designation of hazardous substances.

Code of Federal Regulations, 2014 CFR

2014-07-01

... aldehyde 7421-93-4 2 1 (0.454) ENDRIN AND METABOLITES N.A. 2 ** Endrin, & metabolites 72-20-8 1,2,4 P051 1... diisocyanate 101-68-8 3 5000 (2270) Methyl ethyl ketone 78-93-3 3,4 U159 5000 (2270) Methyl ethyl ketone... U138 100 (45.4) Methyl isobutyl ketone 108-10-1 3,4 U161 5000 (2270) Methyl isocyanate 624-83-9 3,4...

Testing of household products and materials for emission of toluene diisocyanate.

PubMed

Kelly, T J; Myers, J D; Holdren, M W

1999-06-01

Polyurethane products were subjected to chamber testing to determine their emission rates of 2,4- and 2,6-toluene diisocyanate (TDI). The polyurethane (PU) products included carpet padding, furniture cushions, sheet foam, varnishes, and sealants, as well as a commercially-applied water sealant product for concrete that contained up to 4 percent TDI by weight. The PU products were screened in a 9-L glass chamber, under elevated temperature and chamber loading conditions, using both a time-integrated sampling and analysis method specific for TDI and a continuous but non-specific real-time monitor for isocyanates. None of the products normally found in residences showed a positive response in the screening tests, indicating that TDI emissions and consequently toxic effects from such products are negligible. However, the commercially-applied water sealant gave a positive response in the screening test. Further testing of that product at realistic temperatures showed initial TDI emission rates of about 300,000 micrograms/m2/hr, with emissions lasting only one hour or less. At 21 and 27 degrees C, about 1 percent and 5 percent, respectively, of the TDI content of the product was released to the air. The emitted TDI was predominantly the 2,6-isomer, although the TDI originally present in the product was predominantly the 2,4-isomer.

MALDI MS-based Composition Analysis of the Polymerization Reaction of Toluene Diisocyanate (TDI) and Ethylene Glycol (EG).

PubMed

Ahn, Yeong Hee; Lee, Yeon Jung; Kim, Sung Ho

2015-01-01

This study describes an MS-based analysis method for monitoring changes in polymer composition during the polyaddition polymerization reaction of toluene diisocyanate (TDI) and ethylene glycol (EG). The polymerization was monitored as a function of reaction time using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI TOF MS). The resulting series of polymer adducts terminated with various end-functional groups were precisely identified and the relative compositions of those series were estimated. A new MALDI MS data interpretation method was developed, consisting of a peak-resolving algorithm for overlapping peaks in MALDI MS spectra, a retrosynthetic analysis for the generation of reduced unit mass peaks, and a Gaussian fit-based selection of the most prominent polymer series among the reconstructed unit mass peaks. This method of data interpretation avoids errors originating from side reactions due to the presence of trace water in the reaction mixture or MALDI analysis. Quantitative changes in the relative compositions of the resulting polymer products were monitored as a function of reaction time. These results demonstrate that the mass data interpretation method described herein can be a powerful tool for estimating quantitative changes in the compositions of polymer products arising during a polymerization reaction.

New polyurethane/docosane microcapsules as phase-change materials for thermal energy storage.

PubMed

Felix De Castro, Paula; Shchukin, Dmitry G

2015-07-27

Polyurethane microcapsules were prepared by mini-emulsion interfacial polymerization for encapsulation of phase-change material (n-docosane) for energy storage. Three steps were followed with the aim to optimize synthesis conditions of the microcapsules. First, polyurethane microcapsules based on silicone oil core as an inert template with different silicone oil/poly(ethylene glycol)/4,4'-diphenylmethane diisocyanate wt % ratio were synthesized. The surface morphology of the capsules was analyzed by scanning electronic microscopy (SEM) and the chemical nature of the shell was monitored by Fourier transform infrared spectroscopy (FT-IR). Capsules with the silicone oil/poly(ethylene glycol)/4,4'-diphenylmethane diisocyanate 10/20/20 wt % ratio showed the best morphological features and shell stability with average particle size about 4 μm, and were selected for the microencapsulation of the n-docosane. In the second stage, half of the composition of silicone oil was replaced with n-docosane and, finally, the whole silicone oil content was replaced with docosane following the same synthetic procedure used for silicone oil containing capsules. Thermal and cycling stability of the capsules were investigated by thermal gravimetric analysis (TGA) and the phase-change behavior was evaluated by differential scanning calorimetry (DSC). © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Designing an Electronics Data Package for Printed Circuit Boards (PCBs)

DTIC Science & Technology

2013-08-01

finished PCB flatness deviation should be less than 0.010 inches per inch. 4  The minimum copper wall thickness of plated-thru holes should be...Memory Card International Association)  IPC-6015 MCM-L (Multi-Chip Module – Laminated )  IPC-6016 HDI (High Density Interconnect)  IPC-6018...Interconnect ICT In Circuit Tester IPC Association Connecting Electronics Industries MCM-L Multi-Chip Module – Laminated MIL Military NEMA National

United Nations Assistance Mission in Afghanistan: Background and Policy Issues

DTIC Science & Technology

2009-12-14

mainly through U.N. agencies and NGOs. 6 In 2007, Afghanistan placed 174th out of 178 countries on global rankings of the Human Development Index ( HDI ...and other insurgents to reestablish control of some areas of the country have slowed the pace and extent of economic development and the expansion of...improvement throughout the country . The international recovery and reconstruction effort in Afghanistan is immense and complicated and, in coordination

Prevalence and correlates of hypertension in Maharashtra, India: A multilevel analysis

PubMed Central

Bhise, Mahadev D.

2018-01-01

Background and aim In the last few decades, the prevalence of hypertension has been drastically increased in India. The present study estimates the current prevalence of hypertension and its correlates in the state of Maharashtra. The variation in the prevalence of hypertension associated with individual-level characteristics is explained at the community and district level. Methods Data is used from the recent round of District Level Household & Facility Survey (DLHS-4), 2012–13. The DLHS-4 has used the nationally representative sample, collected through multistage stratified sampling procedure. A similar sampling frame, used in NSSO-2007-08, has been followed. The chi-square test is used to show the significance level of the association between the estimated prevalence of hypertension and its correlates. Multilevel regression analysis is carried out to investigate the effects of individual and community level factors on the prevalence of hypertension. Results The overall prevalence of hypertension is 25% in Maharashtra, and a huge variation in the prevalence of hypertension is found across the districts. Dhule, Gadchiroli (with a low HDI rank), Mumbai and Satara (with higher HDI rank) are the districts with the higher (above 30%) prevalence of high blood pressure. The prevalence also significantly varies according to different correlates. The prevalence of high blood pressure is higher among elderly population (40%), among males (28%), in the urban areas (27%) and in the richest wealth quintile (28%). The prevalence is also higher among cigarette smokers (31%), alcohol consumers (30%) and people with obesity (38%) as compared to their counterparts. The results of the multilevel analysis show that the older and obese persons are at four-time higher risk of hypertension. Again, age, sex, marital status, place of residence, wealth status, unhealthy habits (i.e. smoking and alcohol consumption) and BMI are significantly associated with hypertension. The results of VPC statistics show that 14% of hypertension prevalence could be attributed to differences at the community level. Conclusion The prevalence of hypertension largely varies in the districts of Maharashtra irrespective of their level of socio-economic development (i.e. HDI rank). The variation in the rate of prevalence of hypertension is higher in the community (PSU) level as compared to the variation in the prevalence rate at the district level. Hypertension is attributable to the modifiable factors like risky lifestyle practices. PMID:29401464

Association of Sex With the Global Burden of Cataract.

PubMed

Lou, Lixia; Ye, Xin; Xu, Peifang; Wang, Jingyi; Xu, Yufeng; Jin, Kai; Ye, Juan

2018-02-01

Eye disease burden could help guide health policy making. Differences in cataract burden by sex is a major concern of reducing avoidable blindness caused by cataract. To investigate the association of sex with the global burden of cataract by year, age, and socioeconomic status using disability-adjusted life-years (DALYs). This international, comparative burden-of-disease study extracted the global, regional, and national sex-specific DALY numbers, crude DALY rates, and age-standardized DALY rates caused by cataract by year and age from the Global Burden of Disease Study 2015. The DALY data were collected from January 1, 1990, through December 31, 2015, for ever 5 years. The human development index (HDI) in 2015 was extracted as an indicator of national socioeconomic status from the Human Development Report. Comparisons of sex-specific DALY estimates due to cataract by year, age, and socioeconomic status at the global level. Paired Wilcoxon signed rank test, Pearson correlation, and linear regression analyses were performed to evaluate the socioeconomic-associated sex differences in cataract burden. Differences in rates of cataract by sex were similar between 1990 and 2015, with age-standardized DALY rates of 54.5 among men vs 65.0 among women in 1990 and 52.3 among men vs 67.0 among women in 2015. Women had higher rates than men of the same age, and sexual differences increased with age. Paired Wilcoxon signed rank test revealed that age-standardized DALY rates among women were higher than those among men for each HDI-based country group (z range, -4.236 to -6.093; P < .001). The difference (female minus male) in age-standardized DALY rates (r = -0.610 [P < .001]; standardized β = -0.610 [P < .001]) and the female to male age-standardized DALY rate ratios (r = -0.180 [P = .02]; standardized β = -0.180 [P = .02]) were inversely correlated with HDI. Although global cataract health care is progressing, sexual differences in cataract burden showed little improvement in the past few decades. Worldwide, women have a higher cataract burden than men. Older age and lower socioeconomic status are associated with greater differences in rates of cataract by sex. Our findings may enhance public awareness of sexual differences in global cataract burden and emphasize the importance of making sex-sensitive health policy to manage global vision loss caused by cataract.

Prevalence and correlates of hypertension in Maharashtra, India: A multilevel analysis.

PubMed

Bhise, Mahadev D; Patra, Shraboni

2018-01-01

In the last few decades, the prevalence of hypertension has been drastically increased in India. The present study estimates the current prevalence of hypertension and its correlates in the state of Maharashtra. The variation in the prevalence of hypertension associated with individual-level characteristics is explained at the community and district level. Data is used from the recent round of District Level Household & Facility Survey (DLHS-4), 2012-13. The DLHS-4 has used the nationally representative sample, collected through multistage stratified sampling procedure. A similar sampling frame, used in NSSO-2007-08, has been followed. The chi-square test is used to show the significance level of the association between the estimated prevalence of hypertension and its correlates. Multilevel regression analysis is carried out to investigate the effects of individual and community level factors on the prevalence of hypertension. The overall prevalence of hypertension is 25% in Maharashtra, and a huge variation in the prevalence of hypertension is found across the districts. Dhule, Gadchiroli (with a low HDI rank), Mumbai and Satara (with higher HDI rank) are the districts with the higher (above 30%) prevalence of high blood pressure. The prevalence also significantly varies according to different correlates. The prevalence of high blood pressure is higher among elderly population (40%), among males (28%), in the urban areas (27%) and in the richest wealth quintile (28%). The prevalence is also higher among cigarette smokers (31%), alcohol consumers (30%) and people with obesity (38%) as compared to their counterparts. The results of the multilevel analysis show that the older and obese persons are at four-time higher risk of hypertension. Again, age, sex, marital status, place of residence, wealth status, unhealthy habits (i.e. smoking and alcohol consumption) and BMI are significantly associated with hypertension. The results of VPC statistics show that 14% of hypertension prevalence could be attributed to differences at the community level. The prevalence of hypertension largely varies in the districts of Maharashtra irrespective of their level of socio-economic development (i.e. HDI rank). The variation in the rate of prevalence of hypertension is higher in the community (PSU) level as compared to the variation in the prevalence rate at the district level. Hypertension is attributable to the modifiable factors like risky lifestyle practices.

On the Climate Variability and Energy Demands for Indoor Human Comfort Levels in Tropical Urban Environment

NASA Astrophysics Data System (ADS)

Pokhrel, R.; Ortiz, L. E.; González, J. E.; Ramírez-Beltran, N. D.

2017-12-01

The main objective of this study is to identify how climate variability influences human comfort levels in tropical urban environments. San Juan Metropolitan Area (SJMA) of the island of Puerto Rico was chosen as a reference point. A new human discomfort index (HDI) based on environmental enthalpy is defined. This index is expanded to determine the energy required to maintain indoor human comfort levels and was compared to Total Electricity consumption for the Island of Puerto Rico. Regression analysis shows that both Temperature and HDI are good indictor to predict total electrical energy consumption. Results showed that over the past 35 years the average enthalpy have increased and have mostly been above thresholds for human comfort for SJMA. The weather stations data further shows a clear indication of urbanization biases ramping up the index considered. From the trend analysis local scale (weather station) data shows a decreasing rate of maximum cooling at -11.41 kW-h/years, and minimum is increasing at 10.64 kW-h/years. To compare human comfort levels under extreme heat wave events conditions, an event of 2014 in the San Juan area was identified. The analysis for this extreme heat event is complemented by data from the National Center for environmental Prediction (NCEP) at 250km spatial resolution, North American Re-Analysis (NARR) at 32 km spatial resolution, by simulations of the Weather Forecasting System (WRF) at a resolution of 2 km, and by weather station data for San Juan. WRF simulation's results showed an improvement for both temperature and relative humidity from the input NCEP data. It also shows that difference in Energy per Capita (EPC) in urban area during a heat wave event can increase to 16% over a non-urban area. Sensitivity analysis was done by modifying the urban land cover to the most common rural references of evergreen broadleaf forest and cropland to investigate the Urban Heat Island (UHI) effect on HDI. UHI is seen to be maximum during heat wave event during late night and morning hours and minimum during afternoon and late evening hours. The effect of UHI is found to increase the total EPC by 20%.

Seasonal lake surface water temperature trends reflected by heterocyst glycolipid-based molecular thermometers

NASA Astrophysics Data System (ADS)

Bauersachs, T.; Rochelmeier, J.; Schwark, L.

2015-06-01

It has been demonstrated that the relative distribution of heterocyst glycolipids (HGs) in cultures of N2-fixing heterocystous cyanobacteria is largely controlled by growth temperature, suggesting a potential use of these components in paleoenvironmental studies. Here, we investigated the effect of environmental parameters (e.g., surface water temperatures, oxygen concentrations and pH) on the distribution of HGs in a natural system using water column filtrates collected from Lake Schreventeich (Kiel, Germany) from late July to the end of October 2013. HPLC-ESI/MS (high-performance liquid chromatography coupled to electrospray ionization-mass spectrometry) analysis revealed a dominance of 1-(O-hexose)-3,25-hexacosanediols (HG26 diols) and 1-(O-hexose)-3-keto-25-hexacosanol (HG26 keto-ol) in the solvent-extracted water column filtrates, which were accompanied by minor abundances of 1-(O-hexose)-3,27-octacosanediol (HG28 diol) and 1-(O-hexose)-3-keto-27-octacosanol (HG28 keto-ol) as well as 1-(O-hexose)-3,25,27-octacosanetriol (HG28 triol) and 1-(O-hexose)-3-keto-25,27-octacosanediol (HG28 keto-diol). Fractional abundances of alcoholic and ketonic HGs generally showed strong linear correlations with surface water temperatures and no or only weak linear correlations with both oxygen concentrations and pH. Changes in the distribution of the most abundant diol and keto-ol (e.g., HG26 diol and HG26 keto-ol) were quantitatively expressed as the HDI26 (heterocyst diol index of 26 carbon atoms) with values of this index ranging from 0.89 in mid-August to 0.66 in mid-October. An average HDI26 value of 0.79, which translates into a calculated surface water temperature of 15.8 ± 0.3 °C, was obtained from surface sediments collected from Lake Schreventeich. This temperature - and temperatures obtained from other HG indices (e.g., HDI28 and HTI28) - is similar to the one measured during maximum cyanobacterial productivity in early to mid-September and suggests that HGs preserved in the sediment record of Lake Schreventeich reflect summer surface water temperatures. As N2-fixing heterocystous cyanobacteria are widespread in present-day freshwater and brackish environments, we conclude that the distribution of HGs in sediments may allow for the reconstruction of surface water temperatures of modern and potentially ancient lacustrine settings.

Incidence and mortality of lung cancer: global trends and association with socioeconomic status.

PubMed

Wong, Martin C S; Lao, Xiang Qian; Ho, Kin-Fai; Goggins, William B; Tse, Shelly L A

2017-10-30

We examined the correlation between lung cancer incidence/mortality and country-specific socioeconomic development, and evaluated its most recent global trends. We retrieved its age-standardized incidence rates from the GLOBOCAN database, and temporal patterns were assessed from global databases. We employed simple linear regression analysis to evaluate their correlations with Human Development Index (HDI) and Gross Domestic Product (GDP) per capita. The average annual percent changes (AAPC) of the trends were evaluated from join-point regression analysis. Country-specific HDI was strongly correlated with age-standardized incidence (r = 0.70) and mortality (r = 0.67), and to a lesser extent GDP (r = 0.24 to 0.55). Among men, 22 and 30 (out of 38 and 36) countries showed declining incidence and mortality trends, respectively; whilst among women, 19 and 16 countries showed increasing incidence and mortality trends, respectively. Among men, the AAPCs ranged from -2.8 to -0.6 (incidence) and -3.6 to -1.1 (mortality) in countries with declining trend, whereas among women the AAPC range was 0.4 to 8.9 (incidence) and 1 to 4.4 (mortality) in countries with increasing trend. Among women, Brazil, Spain and Cyprus had the greatest incidence increase, and all countries in Western, Southern and Eastern Europe reported increasing mortality. These findings highlighted the need for targeted preventive measures.

Human development, occupational structure and physical inactivity among 47 low and middle income countries

PubMed Central

Atkinson, Kaitlin; Lowe, Samantha; Moore, Spencer

2015-01-01

This study aimed to (a) assess the relationship between a person's occupational category and their physical inactivity, and (b) analyze the association among country-level variables and physical inactivity. The World Health Survey (WHS) was administered in 2002–2003 among 47 low- and middle-income countries (n = 196,742). The International Physical Activity Questionnaire (IPAQ) was used to collect verbal reports of physical activity and convert responses into measures of physical inactivity. Economic development (GDP/c), degree of urbanization, and the Human Development Index (HDI) were used to measure country-level variables and physical inactivity. Multilevel logistic regression analysis was used to examine the association among country-level factors, individual occupational status, and physical inactivity. Overall, the worldwide prevalence of physical inactivity in 2002–2003 was 23.7%. Individuals working in the white-collar industry compared to agriculture were 84% more likely to be physically inactive (OR: 1.84, CI: 1.73–1.95). Among low- and middle-income countries increased HDI values were associated with decreased levels of physical inactivity (OR: 0.98, CI: 0.97–0.99). This study is one of the first to adjust for within-country differences, specifically occupation while analyzing physical inactivity. As countries experience economic development, changes are also seen in their occupational structure, which result in increased countrywide physical inactivity levels. PMID:26844185

Human development, occupational structure and physical inactivity among 47 low and middle income countries.

PubMed

Atkinson, Kaitlin; Lowe, Samantha; Moore, Spencer

2016-06-01

This study aimed to (a) assess the relationship between a person's occupational category and their physical inactivity, and (b) analyze the association among country-level variables and physical inactivity. The World Health Survey (WHS) was administered in 2002-2003 among 47 low- and middle-income countries (n = 196,742). The International Physical Activity Questionnaire (IPAQ) was used to collect verbal reports of physical activity and convert responses into measures of physical inactivity. Economic development (GDP/c), degree of urbanization, and the Human Development Index (HDI) were used to measure country-level variables and physical inactivity. Multilevel logistic regression analysis was used to examine the association among country-level factors, individual occupational status, and physical inactivity. Overall, the worldwide prevalence of physical inactivity in 2002-2003 was 23.7%. Individuals working in the white-collar industry compared to agriculture were 84% more likely to be physically inactive (OR: 1.84, CI: 1.73-1.95). Among low- and middle-income countries increased HDI values were associated with decreased levels of physical inactivity (OR: 0.98, CI: 0.97-0.99). This study is one of the first to adjust for within-country differences, specifically occupation while analyzing physical inactivity. As countries experience economic development, changes are also seen in their occupational structure, which result in increased countrywide physical inactivity levels.

Thermal modeling of head disk interface system in heat assisted magnetic recording

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vemuri, Sesha Hari; Seung Chung, Pil; Jhon, Myung S., E-mail: mj3a@andrew.cmu.edu

2014-05-07

A thorough understanding of the temperature profiles introduced by the heat assisted magnetic recording is required to maintain the hotspot at the desired location on the disk with minimal heat damage to other components. Here, we implement a transient mesoscale modeling methodology termed lattice Boltzmann method (LBM) for phonons (which are primary carriers of energy) in the thermal modeling of the head disk interface (HDI) components, namely, carbon overcoat (COC). The LBM can provide more accurate results compared to conventional Fourier methodology by capturing the nanoscale phenomena due to ballistic heat transfer. We examine the in-plane and out-of-plane heat transfermore » in the COC via analyzing the temperature profiles with a continuously focused and pulsed laser beam on a moving disk. Larger in-plane hotspot widening is observed in continuously focused laser beam compared to a pulsed laser. A pulsed laser surface develops steeper temperature gradients compared to continuous hotspot. Furthermore, out-of-plane heat transfer from the COC to the media is enhanced with a continuous laser beam then a pulsed laser, while the temperature takes around 140 fs to reach the bottom surface of the COC. Our study can lead to a realistic thermal model describing novel HDI material design criteria for the next generation of hard disk drives with ultra high recording densities.« less

Predictive global trends in the incidence and mortality of pancreatic cancer based on geographic location, socio-economic status, and demographic shift.

PubMed

Are, Chandrakanth; Chowdhury, Sanjib; Ahmad, Humera; Ravipati, Advaitaa; Song, Tianqiang; Shrikandhe, Shailesh; Smith, Lynette

2016-11-01

Pancreatic Cancer (PC) is a lethal malignancy that accounts for about 4% of cancer-related deaths worldwide. The aim of this study is to describe the influence of geography (based on WHO regions), socio-economic development (based on Human Development Index [HDI]) and demographic shift on the temporal trends in global incidence and mortality of PC. Data (2012-2030) relating to the incidence, mortality of PC and demographic shifts based on WHO regions and HDI areas were extracted from GLOBOCAN 2012. Linear regression was used to evaluate trends in total incidence and mortality. We noted a definite association between PC and higher socio-economic status. Advanced age (age ≥65) contributed to the rising burden in all socio-economic regions of the world except in the Low Human Development (LHD) countries where the disease predominantly affected population <65 years of age. The global burden of PC is expected to rise significantly over the next few decades regardless of geographic location, socio-economic development, age and gender. Advance knowledge of this data can help formulate strategies to specifically target countries and populations that promote public health policy to tackle this lethal disease on the global stage. J. Surg. Oncol. 2016;114:736-742. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

Polyurethanes from fluoroalkyl propyleneglycol polyethers

NASA Technical Reports Server (NTRS)

Trischler, F. D. (Inventor)

1969-01-01

A description is given of highly stable polyurethane polymers prepared by reacting a polyether with a diisocyanate. Compounded stocks of these polymers may be shaped and cured in conventional equipment used in the rubber industry. The solutions are dispersed gels prepared from the polymers and may be used for forming supported or unsupported films for coating fabrics or solid surfaces, and for forming adhesive bonds between a wide variety of plastics, elastomers, fabrics, metals, wood, leather, ceramics and the like.

Synthesis of Polyurethanes Membranes from Rubber Seed Oil and Methylene Diphenyl Diisocyanates (MDI)

NASA Astrophysics Data System (ADS)

Marlina; Nurman, S.; Saleha, S.; Fitriani; Thanthawi, I.

2017-03-01

Rubber seed oil and methylene diphenyl diisocyanates (MDI) based polyurethane membrane has been prepared in this study. The main objective of this research is manufacture of polyurethane membranes from avocado seed oil, as a filter of this membrane use as a filter of metals from water such as mercury (Hg). In this study, the polyurethane membrane had been synthesized by varying compositions of rubber seed oil and MDI, with ratios of 10:0.2; 10:0.4; 10:0.6; 10:0.8; 10:1.0; 10:1.2; 10:1.4; 10:1.6; 10:1.8 and 10:2.0 (v/w) at 80°C and 170°C as polymerization and curing temperatures, respectively. Optimum polyurethane membrane was obtained at rubber seed oil: MDI 10: 0.8 v/w, it was dry, non-sticky, smooth and blackish brown. The membrane flux was 5,8307 L / m2.h.bar and rejection factor was 35,3015 %. The results of characterization indicated the formation of urethane bonds (NH at 3480 cm-1, C=O at 1620 cm-1, CN at 1374 cm-1, -OC-NH- at 1096 cm-1 and no -NCO at 2270 cm-1), the value of Tg was 55°C. The polyurethane membrane which treated at the optimum treatment conditions were used to the filter of metals from water such as mercury (Hg).

Adhesion of nitrile rubber (NBR) to polyethylene terephthalate (PET) fabric. Part 1: PET surface modification by methylenediphenyl di-isocyanate (MDI)

NASA Astrophysics Data System (ADS)

Razavizadeh, Mahmoud; Jamshidi, Masoud

2016-01-01

Fiber to rubber adhesion is an important subject in rubber composite industry. It is well known that surface physical, mechanical and chemical treatments are effective methods to improve interfacial bonding. Ultra violet (UV) light irradiation is an efficient method which is used to increase interfacial interactions. In this research UV assisted chemical modification of PET fabric was used to increase its bonding to nitrile rubber (NBR). NBR is perfect selection to produce fuel and oil resistant rubber parts but it has weak bonding to fabrics. For this purpose at first, the PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was reacted and grafted to carboxylated PET. T-peel test was used to evaluate PET fabric to NBR bonding strength. Attenuated total reflectance-Fourier transform infrared spectroscopy (FTIR-AT) was used to assess surface modifications of the PET fabrics. The chemical composition of the PET surfaces before and after carboxylation and MDI grafting was investigated by X-ray photoelectron spectroscopy (XPS). It was found that at vulcanizing temperature of 150 °C, carboxylation in contrary to MDI grafting, improved considerably PET to NBR adhesion. Finally effect of curing temperature on PET to NBR bonding strength was determined. It was found that increasing vulcanizing temperature to 170 °C caused considerable improvement (about 134%) in bonding strength.

A follow up study of occupational exposure to 4,4'-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in polyurethane manufacture in the UK.

PubMed

Keen, C; Coldwell, M; McNally, K; Baldwin, P; McAlinden, J; Cocker, J

2012-08-13

This is a follow up survey of exposure to 4,4'-methylene-bis(2-chloroaniline) (MbOCA) and isocyanates in the UK polyurethane industry. Urine samples (n=446) were collected from 90 different workers. MbOCA levels were below the limit of detection in 170 samples and 26 were above the UK Biological Monitoring Guidance Value (BMGV) of 15 μmol MbOCA/mol creatinine. Detailed advice and guidance was given to each workplace at the end of the survey in 2008 and the 90% value reduced from 10 to 3 μmol MbOCA/mol creatinine in samples collected since. There was a positive correlation between glove contamination and urinary MbOCA and levels were dependent upon individual working practices especially how gloves were used. Of the 446 samples analysed for urinary metabolites of toluene diisocyanate 280 were below the detection limit and 126 were above the BMGV (1 μmol/mol creatinine). Of the 326 urine samples that were analysed for metabolites of methylenediphenyl diisocyanate, 270 were below the detection limit and 13 were above the BMGV for isocyanates. There was no correlation between urinary levels of isocyanates and MbOCA suggesting different routes of absorption, most likely inhalation and dermal respectively. Crown Copyright © 2011. Published by Elsevier Ireland Ltd. All rights reserved.

Response of Polyurethane to Shock Waves: An Experimental Investigation

NASA Astrophysics Data System (ADS)

Jayaram, V.; Rao, Keshava Subba; Thanganayaki, N.; Kumara, H. K. T.; Reddy, K. P. J.

Formation of polyurethane (PU) in vacuum environment and controlling density of polyurethane foams are the present day challenges. Polyurethane exists in numerous forms ranging from flexible to rigid and lightweight foams to tough, stiff elastomers [1]. PU can be used to produce lightweight foams for insulation or hard rubber used as wheels to transport heavy loads and it can be used in high pressure applications. The largest volumes of commercial PU elastomers are made from toluene diisocyanate (TDI) or diphenylmethane-4, 4'-diisocyanate (MDI) [2]. Linear polyurethanes can be processed into final products by any of the standard thermoplastic processes (injection molding, extrusion, thermoforming) as well as by low pressure cast processes in presence of catalysts. Tin, tetrabutyl titanate and zirconium chelates are few effective catalysts used to produce polyurethane for particular application [3]. Thermoset elastomers are formed due to irreversible cross-links, when polymers are chemically cured. Highly porous biodegradable PU was synthesized by thermally induced phase separation technique used in tissue engineering and also in bio-degradable based fluids [4]. Properties of PU like hardness, stress/strain modulus, tear strength etc, was determine using ASTM (American Society for Testing and Materials) standard methods. PU possesses extremely high mechanical properties, excellent abrasion, tear and extrusion resistance. It has outstanding low-temperature limit (-600C) and high temperature limit up to (1500C).

Surface modification of calcined kaolin with toluene diisocyanate based on high energy ball milling

NASA Astrophysics Data System (ADS)

Yuan, Yongbing; Chen, Hongling; Lin, Jinbin; Ji, Yan

2013-11-01

The surface of calcined kaolin particle was modified with toluene diisocyanate (TDI) by using high energy ball milling. The prepared hybrids were characterized by FT-IR, MAS NMR, thermal analysis (TGA-DSC), static water contact angle (CA), apparent viscosity and transmission electron microscopy (TEM). FT-IR and MAS NMR spectra demonstrated that TDI molecules were chemically anchored to kaolin surface after modification. The results of thermal analysis showed that the maximum grafting ratio reached up to 446.61% when the mass ratio of TDI/kaolin was 0.5:1.0, and CA measurements revealed that the resultant hybrids exhibited strong hydrophobicity (148.82°). Apparent viscosity and TEM were employed to examine the dispersion properties of blank and modified kaolin particles in poly (dimenthylsiloxane) matrix. The results illustrated that the dispersion stability depended strongly on the grafting ratio of TDI, neither too low nor too high achieved uniform and stable dispersion, and the favorable grafting ratio was obtained when the mass ratio of TDI/kaolin was 0.2:1.0. Further modification of TDI/kaolin (mass ration of TDI/kaolin, 1.0:1.0) particles with bis(aminopropyl)-terminated-poly(dimethylsiloxane) (APS) was also investigated. TEM evidenced that the dispersion properties of the obtained TDI/APS/kaolin particles were remarkably improved in octamethyl cyclotetrasiloxane compared with the original TDI/kaolin particles.

FTIR spectroscopic characterization of polyurethane-urea model hard segments (PUUMHS) based on three diamine chain extenders

NASA Astrophysics Data System (ADS)

Zhang, Shijie; Ren, Zhiyong; He, Suqing; Zhu, Yan; Zhu, Chengshen

2007-01-01

Six polyurethane-urea model hard segments (PUUMHS) were prepared by a solution method based, respectively, on two isocyanates: 4,4'-methylene-diphenyl-diisocyanate (MDI), 4,4'-methylene-dicyclohexyl diisocyanate (HMDI) and three amine chain extenders: ethylene diamine (EDA), methylene-bis-ortho-chloroaniline (MOCA), 2,4-diamino-3,5-dimethylsuphylchlorobenzene (DDSCB). FTIR was used to study their spectroscopic characterization. The main FTIR bands of the six samples were assigned and compared. It was found that most of N-H and C dbnd O are H-bonded in these PUUMHS. However, the N-H in three MDI based PUUMHS is all in the stronger H-bond state than that in their corresponding HMDI based while the C dbnd O in three HMDI based PUUMHS is all in the stronger H-bond state than that in their corresponding MDI based, respectively. In addition, the order of the H-bond strength in HMDI based PUUMHS is MOCA, DDSCB and EDA whether according to νN sbnd H or νC dbnd O band wavenumbers, which is, however, different from that in MDI based PUUMHS. Moreover, the HMDI based PUUMHS shows obvious double amide III bands while the MDI based has only prominent one. The results are discussed according mainly to the different characteristics of the three chain extenders as well as the structure difference between MDI and HMDI.

Toluene diisocyanate concentration investigation among TDI-related factories in Taiwan and their relations to the type of industry.

PubMed

Yeh, Hui-Jung; Shih, Tung-Sheng; Tsai, Perng-Jy; Chang, Ho-Yuan

2002-03-01

To determine nationwide 2,4- and 2,6-toluene diisocyanates (TDI) concentrations among polyurethane (PU) resin, PU foam, and other TDI-related industries in Taiwan. The ratios of 2,4-/2,6-TDI and the noncarcinogenic risk among these three industries were also investigated. Personal and fixed-area monitoring of TDI concentrations as well as questionnaires were performed for 26 factories in Taiwan. The modified OHSA 42 method was applied in sampling and analysis. Noncarcinogenic hazard index was estimated for these three industries based on the average concentration measurements. Significant differences of TDI concentrations were found among the three industry categories. For personal monitoring, PU foam was found to have the highest TDI levels [18.6 (+/-33.6) and 22.1 (+/-42.3) ppb for 2,4- and 2,6-TDI], Others average [8.3 (+/-18.9) and 10.2 (+/-17.2) ppb], and PU resin lowest [2.0 (+/-3.5) and 0.7 (+/-1.2) ppb]. The estimated average hazard indices were found to be 310-3310. A substantial percentage of airborne TDI concentrations among in Taiwan industries exceeded current TDI occupational exposure limit, and significant difference of TDI levels were found among the three industry categories. The control remedy for the tasks of charging and foaming should be enforced with the highest priority. A separate 2,6-TDI exposure standard is warranted.

Nanoscale modeling for ultrathin liquid films: Spreading and coupled layering

NASA Astrophysics Data System (ADS)

Phillips, David Michael

The hard disk drive (HDD) industry is currently experiencing a compound annual growth rate of 100% for the areal density. Current production drives have an areal density of 80 Gbit in-2, and drives with an areal density of 100 Gbit in-2 have been recently demonstrated. While much of this growth has been fueled by the development of new read/write heads, some of this gain was achieved by reducing the spacing between the heads and the magnetic media. This in turn reduces the spacing at the head-disk interface (HDI). The HDI in a HDD system consists of a slider, which contains the read/write heads, flying over the disk surface on an air bearing. The current designed separation distance, or fly height, is less than 10 nm. This spacing is expected to reduce to a mere 5 nm within the next few years. With the reduced fly height, intermittent contacts at the HDI become more probable. Only a thin lubricant film of perfluoropolyether (PFPE) and a sputtered carbon overcoat on the disk surface protect the slider and the stored data from mechanical and thermal damage. The PFPE film is quite thin, with a thickness of less than 2 nm or about a monolayer of molecules. During an HDI contact, the PFPE film is considered sacrificial and is often depleted in the contact area. In order to maintain adequate protection for the disk surface, PFPE molecules from the surrounding film must replenish the depleted area. This replenishment ability directly opposes the requirement that the PFPE film must not spin-off of the disk surface due to the disk rotation rate, which is as high as 10,000 RPM in current drives. To balance the PFPE films to sufficiently meet both requirements, HDD manufacturers functionalized the endgroups of the PFPE molecules to allow some portion of the lubricant film to reversibly bond with the disk overcoat. The result is a lubricant film that has a slower replenishment but does not spin-off. The work presented here focuses on the replenishment ability of thin films of liquid PFPE. The experimental analogue of replenishment is the one-dimensional spreading analysis. PFPEs with functional endgroups demonstrated coupled molecular layering and dewetting phenomena during the spreading analysis, while PFPEs with nonfunctional endgroups did not. All of the PFPE thin films spread via a diffusive process and had diffusion coefficients that depended on the local film thickness. A theoretical analysis is presented here for both the governing equation and the disjoining pressure driving force for the PFPE thin film spreading. For PFPEs with non-functional endgroups, a reasonable analysis is performed on the diffusion coefficient for two classes of film: submonolayer and multilayer. The diffusion coefficient of PFPEs with functional endgroups are qualitatively linked to the gradient of the film disjoining pressure. To augment this theory, both lattice-based and off-lattice Monte Carlo simulations are conducted for PFPE film models. The lattice-based model shows the existence of a critical functional endgroup interaction strength. It is also used to study the break-up of molecular layers for a spreading film via a fractal analysis. The off-lattice model is used to calculate the anisotropic pressure tensor for the model PFPE thin film and subsequently the film disjoining pressure. The model also qualitatively analyzes of the self diffusion in the film.

Inhibition of HIF-2.alpha. heterodimerization with HIF1.beta. (ARNT)

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bruick, Richard K.; Caldwell, Charles G.; Frantz, Doug E.

2017-09-12

Provided is a method of inhibiting heterodimerization of HIF-2.alpha. to HIF1.beta. (ARNT) comprising binding certain small molecules to the HIF-2.alpha. PAS-B domain cavity but not to HIF1.alpha. and inhibiting HIF-2.alpha. heterodimerization to HIF1.beta. (ARNT) but not inhibiting HIF1.alpha. heterodimerization to HIF1.beta. (ARNT). Those certain small molecules are also referenced synonymously as HIF2-HDI and HIF2.alpha. heterodimerization inhibitors and also simply as certain small molecules.

Operations Research Techniques for Human Factors Engineers

DTIC Science & Technology

1985-06-01

mathematical than Raiffa’s explanations. b) Raiffa, Howard. Decision Analisis : Introductory Lectutres on Choiceg~~a hdY9ETny a--s- s- se ia fly, 1968. A...response criterion (8)- d) Pastore , R.E., and Scheirer, C.J. "Signal Detection Theory: Considerations for General Application " itPs Nholo_ cal Bulletin...Relatioship: . N9--1: Joi Vonn rey and Sons, Tr-rppnT35 p -TT. 26. Rouse, William B. System Enin eerin? Models of Human-Machine Interaction. New Y E

Applications of polymer coatings for the fabrication of copper-based containers for the ultimate disposal of Canada's spent nuclear fuel

NASA Astrophysics Data System (ADS)

Mortley, Aba

Oxygen-free, phosphorous doped copper containers have been proposed for the storage of the used nuclear fuel bundles as a part of Canada's multi-barrier, adaptive phased management procedure for long term storage of spent nuclear fuel bundles. The spent nuclear fuel disposal system proposed for Canada has been engineered based on the multi-barrier approach intended to minimize the risk that the radioactive materials enter the biosphere. Copper is known to be susceptible to corrosion and it is thought that the simultaneous exposure to aggressive ionizing radiation field and residual heat produced by the spent nuclear fuel and the surrounding groundwater would all challenge the container's integrity. The goal of the present work is to reduce the impact of corrosion in the early stages of emplacement with the addition of a protective coating. Specifically, castor oil based polyurethanes were assessed as coatings and their ability to act as an additional physical barrier in the multi-barrier system mentioned previously. The novelty of this work stems from the use of a naturally derived non-petroleum based material in the form of castor oil as the polyol component. Two types of castor oil polyurethanes were investigated, one based on an aliphatic hexamethylene diisocyanate (HMDI), and the other based on an aromatic 2,4-toluene diisocyanate (TDI). Radiation and saturation tests were conducted using varying conditions. Mixed field ionizing radiation was provided by a SLOWPOKE-2 pool-type nuclear research reactor, up to accumulated doses of 6 MGy at dose rates of 37 kGy h-1 and 55.5 kGy h-1. Weight gain immersion studies, at temperatures of 25° C, 50° C, 70° C, were used to determine the mass uptake of several different solutions. The solutions utilized in the present work included hydrochloric acids of varying pHs, distilled water, and buffered solutions, which simulated chloride and sulphide rich calcium-sodium bicarbonate waters. After being exposed to radiation and saturation individually and in several combinations, the polymer samples were tested using a battery of tests. These tests were used to determine how the physico-mechanical properties of the materials, such as their strength, and their ability to be deformed and stretched were affected by radiation. The gist of these tests being that, if the sample showed significant variations in the physico-mechanical properties, then the material would be deemed as unacceptable for use in combined radiation-temperature-pH environments of the deep geological repository (DGR). The tests used included: Fourier transform infrared spectroscopy (FTIR), Matrix-assisted laser desorption/ionization (MALDI) spectroscopy, electronic ionization mass spectroscopy (EI MS), wide angle x-ray scattering (WAXS), solid-state nuclear magnetic resonance ( 13C-NMR), dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). Radiation dose increases from 0 MGy to 2.0 MGy showed a four-fold increase from 0.930 MPa to 4.365 MPa in the initial modulus and 0.149 MPa to 0.747 MPa in the tensile strength values of the polyurethanes. Above 2.0 MGy, the modulus and the tensile strength values exhibited a plateau at values above those of the unirradiated samples. The sorption and diffusion experiments demonstrated a mass uptake of less than 2 %, regardless of what polar solution was used. As a reflection of the more rigid polymer matrix provided by the aromatic ring, the aromatic polyurethanes generally exhibited higher modulus and tensile strength values and lower solution mass uptake and diffusivities. The diffusion values ranged from 8.5 x 10-7 cm2 s-1 to 3.31 X 10-6 cm2 s -1 for the aliphatic polyurethanes and 8.8 x 10-7 cm 2 s-1 to 1.60 x 10-6 cm2 S-1 for the aromatic polyurethanes. The order in which the experimental conditions were applied, Le. sequentially or simultaneously, had definite effects on the finished product. However, regardless of the manner in which the radiation and saturation were combined, in a sequential or simultaneous manner, the end results showed that the moduli values remained above those of the virgin samples (> 2 MPa). The results of the present work indicate that the castor oil based polyurethanes may indeed be used as a viable material where the end-use conditions include combined radiation-thermal-pH environments such as part of the container to store used nuclear fuel. Future development on this work can look at how the adhesive qualities between the castor oil based polyurethanes and the metal copper container may change in such environments.

Synthesis and Characterization of Mesoporous Silica Functionalized with Calix[4]arene Derivatives

PubMed Central

Alahmadi, Sana M.; Mohamad, Sharifah; Maah, Mohd Jamil

2012-01-01

This work reports a new method to covalently attach calix[4]arene derivatives onto MCM-41, using a diisocyanate as a linker. The modified mesoporous silicates were characterized by fourier transform infrared spectroscopy (FTIR), thermal analysis (TGA) and elemental analysis. The FTIR spectra and TGA analysis verified that the calix[4]arene derivates are covalently attached to the mesoporous silica. The preservation of the MCM-41 channel system was checked by X-ray diffraction and nitrogen adsorption analysis. PMID:23202977

Pervaporation separation of ethanol-water mixtures using polyethylenimine composite membranes

DOEpatents

Neidlinger, H.H.; Schissel, P.O.; Orth, R.A.

1987-04-21

Synthetic, organic, polymeric membranes were prepared from polyethylenimine for use with pervaporation apparatus in the separation of ethanol-water mixtures. The polymeric material was prepared in dilute aqueous solution and coated onto a polysulfone support film, from which excess polymeric material was subsequently removed. Cross-links were then generated by limited exposure to toluene-2,4-diisocyanate solution, after which the prepared membrane was heat-cured. The resulting membrane structures showed high selectivity in permeating ethanol or water over a wide range of feed concentrations.

Pervaporation separation of ethanol-water mixtures using polyethylenimine composite membranes

DOEpatents

Neidlinger, Hermann H.; Schissel, Paul O.; Orth, Richard A.

1987-01-01

Synthetic, organic, polymeric membranes were prepared from polyethylenimine for use with pervaporation apparatus in the separation of ethanol-water mixtures. The polymeric material was prepared in dilute aqueous solution and coated onto a polysulfone support film, from which excess polymeric material was subsequently removed. Cross-links were then generated by limited exposure to toluene-2,4-diisocyanate solution, after which the prepared membrane was heat-cured. The resulting membrane structures showed high selectivity in permeating ethanol or water over a wide range of feed concentrations.

Development of low viscosity alkane-based urethane for connector potting applications

NASA Technical Reports Server (NTRS)

Morris, D. E.

1983-01-01

Two series of saturated hydrocarbon-based urethanes were prepared with isophorone diisocyanate and one series with methyl bis (4-cyclohexyl isocyanate). The urethanes with molecular weights as great as 2500 had viscosities low enough and a working life long enough to be used in potting, molding, and coating applications. Specimens were prepared and mechanical properties such as hardness, tensile strength elongation, and tear strength were determined. Thermomechanical properties (glass transition and expansion coefficient) and thermogravimetric properties were determined.

Diagnostic ultrasound and telemedicine utilization in the international space station

NASA Astrophysics Data System (ADS)

Carter, Stephen J.; Stewart, Brent K.; Kushmerick, Martin J.; Langer, Steve G.; Schmiedl, Udo P.; Winter, Thomas C.; Conley, Kevin E.; Jubrias, Sharon A.

1999-01-01

Clinical diagnostic ultrasound (US) is experiencing an expanding role that is well suited to application on the International Space Station (ISS). Diagnostic US can be used to reduce the risks associated with long duration human space flight by providing a non-invasive tool with head-to-toe diagnostic capability in both biomedical research and crew health care. General health care of the astronauts will be diagnosed with US, e.g., kidney stones, gall bladder disease, appendicitis, etc. Initial studies will focus on detection of ``ureteral jets'' in the bladder. This is a non-invasive test to rule out obstructive uropathy from kidney stones with minimal requirements for crew training. Biomedical research experiments, focusing on the effects of the microgravity environment, will be performed using both the HHU and the HDI 5000. US will be used to evaluate bone density and muscle mass in this environment. Prolonged or emergency EVAs may occur with the ISS. The hand-held ultrasound unit (HHU) and its telemedicine capability will be used in EVA settings to monitor events such as decompression sickness (DCS) microbubble formation in the cardiovascular system. There will be telemetry links between the HHU and the ATL/Lockheed Martin rack mounted HDI 5000 in the ISS Human Research Facility (HRF), as well as between the HRF and medical expertise on the ground. These links will provide the ISS with both real-time and store-and-forward telemedicine capabilities. The HHU can also be used with the existing telemedicine instrument pack (TIP).

Obsessive-compulsive personality disorder features and response to behavioral therapy for insomnia among patients with hypnotic-dependent insomnia.

PubMed

Petrov, Megan E; Emert, Sarah E; Lichstein, Kenneth L

2018-06-05

To compare therapeutic response to behavioral therapy for insomnia (BT-I) among hypnotic-dependent insomnia (HDI) patients with and without Cluster C personality disorders. Twenty-three adults with HDI (17 females), aged between 33 and 68 (M = 53; SD = 9.9) were included in the study. Participants completed a personality disorder assessment (baseline), as well as sleep diaries, polysomnography (PSG), and an insomnia severity assessment (baseline, posttreatment, and one-year follow-up). Treatment consisted of eight weeks of individual BT-I and gradual hypnotic medication withdrawal. Multilevel mixed-effects linear regression models examined the interaction between study visit and Cluster C personality disorders status on treatment response to BT-I. Obsessive-compulsive personality disorder (OCPD) was the most prevalent of the Cluster C personality disorders with 38% (n = 8) of participants meeting criteria. There were no significant treatment differences by OCPD status across time as measured by sleep diaries and insomnia severity status. However, there were significant treatment differences by OCPD status by one-year follow-up on PSG outcomes, indicating that patients with OCPD status had shorter and more disrupted sleep than patients without OCPD status. Based on self-reported sleep measures, patients with insomnia and features of OCPD responded equivalently to BT-I at one-year follow-up compared to patients without features of OCPD. However, polysomnography outcomes indicated objective sleep deteriorated in these patients, which may suggest greater vulnerability to relapse.

Simple vs. Complex Carbohydrate Dietary Patterns and the Global Overweight and Obesity Pandemic.

PubMed

Ferretti, Fabrizio; Mariani, Michele

2017-10-04

Nowadays, obesity and being overweight are among the major global health concerns. Many, diet-related diseases impose high tangible and intangible costs, and threaten the sustainability of health-care systems worldwide. In this study, we model, at the macroeconomic level, the impact of energy intake from different types of carbohydrates on the population's BMI (body mass index). We proceed in three steps. First, we develop a framework to analyse both the consumption choices between simple and complex carbohydrates and the effects of these choices on people health conditions. Second, we collect figures for 185 countries (over the period 2012-2014) regarding the shares of simple (sugar and sweetener) and complex (cereal) carbohydrates in each country's total dietary energy supply. Third, we use regression techniques to: (1) estimate the impact of these shares on the country's prevalence of obesity and being overweight; (2) compute for each country an indicator of dietary pattern based on the ratio between simple and complex carbohydrates, weighted by their estimated effects on the prevalence of obesity and being overweight; and (3) measure the elasticity of the prevalence of obesity and being overweight with respect to changes in both carbohydrate dietary pattern and income per capita. We find that unhealthy eating habits and the associated prevalence of excessive body fat accumulation tend to behave as a 'normal good' in low, medium- and high-HDI (Human Development Index) countries, but as an 'inferior good' in very high-HDI countries.

Therapeutic Risk and Benefits of Concomitantly Using Herbal Medicines and Conventional Medicines: From the Perspectives of Evidence Based on Randomized Controlled Trials and Clinical Risk Management

PubMed Central

Zhang, Xiu-lai; Chen, Meng; Zhu, Ling-ling

2017-01-01

Despite increased awareness of the potential of herb-drug interactions (HDIs), the lack of rigorous clinical evidence regarding the significance provides a challenge for clinicians and consumers to make rational decisions about the safe combination of herbal and conventional medicines. This review addressed HDIs based on evidence from randomized controlled trials (RCTs). Literature was identified by performing a PubMed search till January 2017. Risk description and clinical risk management were described. Among 74 finally included RCTs, 17 RCTs (22.97%) simply addressed pharmacodynamic HDIs. Fifty-seven RCTs (77.03%) investigated pharmacokinetic HDIs and twenty-eight of them showed potential or actual clinical relevance. The extent of an HDI may be associated with the factors such as pharmacogenomics, dose of active ingredients in herbs, time course of interaction, characteristics of the object drugs (e.g., administration routes and pharmacokinetic profiles), modification of herbal prescription compositions, and coexistence of inducers and inhibitors. Clinical professionals should enhance risk management on HDIs such as increasing awareness of potential changes in therapeutic risk and benefits, inquiring patients about all currently used conventional medicines and herbal medicines and supplements, automatically detecting highly substantial significant HDI by computerized reminder system, selecting the alternatives, adjusting dose, reviewing the appropriateness of physician orders, educating patients to monitor for drug-interaction symptoms, and paying attention to follow-up visit and consultation. PMID:28491115

Isocyanate Cross-Linked Silica: Structurally Strong Aerogels

NASA Technical Reports Server (NTRS)

Leventis, Nicholas; Sotiriou-Leventis, Chariklia; Zhang, Guo-Hui; Rawashdeh, Abdel-Monem M.

2002-01-01

Molecular-level synergism between the silica nanoparticles of pre-formed monoliths and molecular cross-linkers inverts the relative host-guest roles in glass-polymer composites, leading to new strong low-density materials. Attempts to load gels with variable amounts of polyurethane precursors such as di-ISO and diol end-capped polybutylene adipate followed by heat treatment, washing, and supercritical drying led to opaque materials, somewhat stronger than silica but still quite brittle and much inferior to the materials described above. Direct mixing of a diisocyanate and an alcohol-free sol has been attempted recently by Yim et al. Reportedly, that procedure leads to week-long gelation times and requires an at least equally long aging period. In our attempt to add various amounts of di-ISO in a base-catalyzed sol in PC, we also noticed a week-long gelation time. The resulting aerogels were translucent but no less brittle than native silica. According to more recent studies, if propylene carbonate is replaced with acetone, it leads not only to shorter processing times, but also to much stronger gels that can tolerate loads in excess of 40 kg in the arrangement presented. We attribute that behavior to the lower viscosity of acetone, that allows faster diffusion of the di-ISO solution within the pores before di-ISO has time to react with the surface of silica. Further studies are underway to vary the chemical identity of the diisocyanate, as well as the composition and density of silica.