Superior cycle performance and high reversible capacity of SnO2/graphene composite as an anode material for lithium-ion batteries

PubMed Central

Liu, Lilai; An, Maozhong; Yang, Peixia; Zhang, Jinqiu

2015-01-01

SnO2/graphene composite with superior cycle performance and high reversible capacity was prepared by a one-step microwave-hydrothermal method using a microwave reaction system. The SnO2/graphene composite was characterized by X-ray diffraction, thermogravimetric analysis, Fourier-transform infrared spectroscopy, Raman spectroscopy, scanning electron microscope, X-ray photoelectron spectroscopy, transmission electron microscopy and high resolution transmission electron microscopy. The size of SnO2 grains deposited on graphene sheets is less than 3.5 nm. The SnO2/graphene composite exhibits high capacity and excellent electrochemical performance in lithium-ion batteries. The first discharge and charge capacities at a current density of 100 mA g−1 are 2213 and 1402 mA h g−1 with coulomb efficiencies of 63.35%. The discharge specific capacities remains 1359, 1228, 1090 and 1005 mA h g−1 after 100 cycles at current densities of 100, 300, 500 and 700 mA g−1, respectively. Even at a high current density of 1000 mA g−1, the first discharge and charge capacities are 1502 and 876 mA h g−1, and the discharge specific capacities remains 1057 and 677 mA h g−1 after 420 and 1000 cycles, respectively. The SnO2/graphene composite demonstrates a stable cycle performance and high reversible capacity for lithium storage. PMID:25761938

Development of Large-Format Lithium-Ion Cells with Silicon Anode and Low Flammable Electrolyte

NASA Technical Reports Server (NTRS)

Wu, James J.; Hernandez-Lugo, D. M.; Smart, M. C.; Ratnakumar, B. V.; Miller, T. B.; Lvovich, V. F.; Lytle, J. K.

2014-01-01

NASA is developing safe, high energy and high capacity lithium-ion cell designs and batteries for future missions under NASAs Advanced Space Power System (ASPS) project. Advanced cell components, such as high specific capacity silicon anodes and low-flammable electrolytes have been developed for improving the cell specific energy and enhancing safety. To advance the technology readiness level, we have developed large-format flight-type hermetically sealed battery cells by incorporating high capacity silicon anodes, commercially available lithium nickel, cobalt, aluminum oxide (NCA) cathodes, and low-flammable electrolytes. In this report, we will present the performance results of these various battery cells. In addition, we will also discuss the post-test cell analysis results as well.

Well-ordered mesoporous Fe2O3/C composites as high performance anode materials for sodium-ion batteries.

PubMed

Li, Mei; Ma, Chao; Zhu, Qian-Cheng; Xu, Shu-Mao; Wei, Xiao; Wu, Yong-Min; Tang, Wei-Ping; Wang, Kai-Xue; Chen, Jie-Sheng

2017-04-11

Sodium-ion batteries have attracted considerable attention in recent years. In order to promote the practical application of sodium-ion batteries, the electrochemical performances, such as specific capacity, reversibility, and rate capability of the anode materials, should be further improved. In this work, a Fe 2 O 3 /C composite with a well-ordered mesoporous structure is prepared via a facile co-impregnation method by using mesoporous silica SBA-15 as a hard template. When used as an anode material for sodium-ion batteries, the well-ordered mesoporous structure ensures fast mass transport kinetics. The presence of nano-sized Fe 2 O 3 particles confined within the carbon walls significantly enhances the specific capacity of the composite. The carbon walls in the composite act not only as an active material contributing to the specific capacity, but also as a conductive matrix improving the cycling stability of Fe 2 O 3 nanoparticles. As a result, the well-ordered mesoporous Fe 2 O 3 /C composite exhibits high specific capacity, excellent cycleability, and high rate capability. It is proposed that this simple co-impregnation method is applicable for the preparation of well-ordered mesoporous transition oxide/carbon composite electrode materials for high performance sodium-ion and lithium-ion batteries.

Two-dimensional ultra-thin SiO(x) (0 < x < 2) nanosheets with long-term cycling stability as lithium ion battery anodes.

PubMed

Sun, Lin; Su, Tingting; Xu, Lei; Liu, Meipin; Du, Hong-Bin

2016-03-21

Ultra-thin SiO(x) (0 < x < 2) nanosheets were obtained via a convenient solvothermal route from a Zintl compound CaSi2. After carbon coating, the SiOx@C nanosheet anodes exhibit high capacity, good rate and superior cycling performance for high-capacity lithium ion battery applications. The specific capacity can be maintained as high as 760 mA h g(-1) with almost no capacity decay after 400 cycles at a current density of 0.5 A g(-1).

Developing a Personnel Capacity Indicator for a high turnover Cartographic Production Sector

NASA Astrophysics Data System (ADS)

Mandarino, Flávia; Pessôa, Leonardo A. M.

2018-05-01

This paper describes a framework for development of an indicator for human re-sources capacity management in a military organization responsible for nautical chart production. Graphic chart for the results of the model COPPE-COSENZA (Cosenza et al. 2015) is used to properly present the personnel capacity within a high people turnover environment. The specific skills for the nautical charts production allied to the turnover rate require continuous and adequate personnel in-corporation and a capacity building through education and on-the-job training. The adopted approach for the study establishes quantitative values to fulfill quality requirements, and also presents graphically a profile for the human resources on a specific job to facilitate diagnosis and corrective actions.

Si-Mn/reduced graphene oxide nanocomposite anodes with enhanced capacity and stability for lithium-ion batteries.

PubMed

Park, A Reum; Kim, Jung Sub; Kim, Kwang Su; Zhang, Kan; Park, Juhyun; Park, Jong Hyeok; Lee, Joong Kee; Yoo, Pil J

2014-02-12

Although Si is a promising high-capacity anode material for Li-ion batteries (LIB), it suffers from capacity fading due to excessively large volumetric changes upon Li insertion. Nanocarbon materials have been used to enhance the cyclic stability of LIB anodes, but they have an inherently low specific capacity. To address these issues, we present a novel ternary nanocomposite of Si, Mn, and reduced graphene oxide (rGO) for LIB anodes, in which the Si-Mn alloy offers high capacity characteristics and embedded rGO nanosheets confer structural stability. Si-Mn/rGO ternary nanocomposites were synthesized by mechanical complexation and subsequent thermal reduction of mixtures of Si nanoparticles, MnO2 nanorods, and rGO nanosheets. Resulting ternary nanocomposite anodes displayed a specific capacity of 600 mAh/g with ∼90% capacity retention after 50 cycles at a current density of 100 mA/g. The enhanced performance is attributed to facilitated Li-ion reactions with the MnSi alloy phase and the formation of a structurally reinforced electroconductive matrix of rGO nanosheets. The ternary nanocomposite design paradigm presented in this study can be exploited for the development of high-capacity and long-life anode materials for versatile LIB applications.

Lithium storage in structurally tunable carbon anode derived from sustainable source

DOE PAGES

Lim, Daw Gen; Kim, Kyungho; Razdan, Mayuri; ...

2017-09-01

Here, a meticulous solid state chemistry approach has been developed for the synthesis of carbon anode from a sustainable source. The reaction mechanism of carbon formation during pyrolysis of sustainable feed-stock was studied in situ by employing Raman microspectroscopy. No Raman spectral changes observed below 160°C (thermally stable precursor) followed by color change, however above 280°C characteristic D and G bands of graphitic carbon are recorded. Derived carbon particles exhibited high specific surface area with low structural ordering (active carbons) to low specific surface area with high graphitic ordering as a function of increasing reaction temperature. Carbons synthesized at 600°Cmore » demonstrated enhanced reversible lithiation capacity (390 mAh g -1), high charge-discharge rate capability, and stable cycle life. On the contrary, carbons synthesized at higher temperatures (>1200°C) produced more graphite-like structure yielding longer specific capacity retention with lower reversible capacity.« less

Tunneled Mesoporous Carbon Nanofibers with Embedded ZnO Nanoparticles for Ultrafast Lithium Storage.

PubMed

An, Geon-Hyoung; Lee, Do-Young; Ahn, Hyo-Jin

2017-04-12

Carbon and metal oxide composites have received considerable attention as anode materials for Li-ion batteries (LIBs) owing to their excellent cycling stability and high specific capacity based on the chemical and physical stability of carbon and the high theoretical specific capacity of metal oxides. However, efforts to obtain ultrafast cycling stability in carbon and metal oxide composites at high current density for practical applications still face important challenges because of the longer Li-ion diffusion pathway, which leads to poor ultrafast performance during cycling. Here, tunneled mesoporous carbon nanofibers with embedded ZnO nanoparticles (TMCNF/ZnO) are synthesized by electrospinning, carbonization, and postcalcination. The optimized TMCNF/ZnO shows improved electrochemical performance, delivering outstanding ultrafast cycling stability, indicating a higher specific capacity than previously reported ZnO-based anode materials in LIBs. Therefore, the unique architecture of TMCNF/ZnO has potential for use as an anode material in ultrafast LIBs.

Rapidly Synthesized, Few-Layered Pseudocapacitive SnS2 Anode for High-Power Sodium Ion Batteries.

PubMed

Thangavel, Ranjith; Samuthira Pandian, Amaresh; Ramasamy, Hari Vignesh; Lee, Yun-Sung

2017-11-22

The abundance of sodium resources has recently motivated the investigation of sodium ion batteries (SIBs) as an alternative to commercial lithium ion batteries. However, the low power and low capacity of conventional sodium anodes hinder their practical realization. Although most research has concentrated on the development of high-capacity sodium anodes, anodes with a combination of high power and high capacity have not been widely realized. Herein, we present a simple microwave irradiation technique for obtaining few-layered, ultrathin two-dimensional SnS 2 over graphene sheets in a few minutes. SnS 2 possesses a large number of active surface sites and exhibits high-capacity, rapid sodium ion storage kinetics induced by quick, nondestructive pseudocapacitance. Enhanced sodium ion storage at a high current density (12 A g -1 ), accompanied by high reversibility and high stability, was demonstrated. Additionally, a rationally designed sodium ion full cell coupled with SnS 2 //Na 3 V 2 (PO 4 ) 3 exhibited exceptional performance with high initial Coulombic efficiency (99%), high capacity, high stability, and a retention of ∼53% of the initial capacity even after the current density was increased by a factor of 140. In addition, a high specific energy of ∼140 Wh kg -1 and an ultrahigh specific power of ∼8.3 kW kg -1 (based on the mass of both the anode and cathode) were observed. Because of its outstanding performance and rapid synthesis, few-layered SnS 2 could be a promising candidate for practical realization of high-power SIBs.

Silicon oxide based high capacity anode materials for lithium ion batteries

DOEpatents

Deng, Haixia; Han, Yongbong; Masarapu, Charan; Anguchamy, Yogesh Kumar; Lopez, Herman A.; Kumar, Sujeet

2017-03-21

Silicon oxide based materials, including composites with various electrical conductive compositions, are formulated into desirable anodes. The anodes can be effectively combined into lithium ion batteries with high capacity cathode materials. In some formulations, supplemental lithium can be used to stabilize cycling as well as to reduce effects of first cycle irreversible capacity loss. Batteries are described with surprisingly good cycling properties with good specific capacities with respect to both cathode active weights and anode active weights.

Cobalt Oxide Porous Nanofibers Directly Grown on Conductive Substrate as a Binder/Additive-Free Lithium-Ion Battery Anode with High Capacity.

PubMed

Liu, Hao; Zheng, Zheng; Chen, Bochao; Liao, Libing; Wang, Xina

2017-12-01

In order to reduce the amount of inactive materials, such as binders and carbon additives in battery electrode, porous cobalt monoxide nanofibers were directly grown on conductive substrate as a binder/additive-free lithium-ion battery anode. This electrode exhibited very high specific discharging/charging capacities at various rates and good cycling stability. It was promising as high capacity anode materials for lithium-ion battery.

Assessing Capacity for Sustainability of Effective Programs and Policies in Local Health Departments.

PubMed

Tabak, Rachel G; Duggan, Katie; Smith, Carson; Aisaka, Kristelle; Moreland-Russell, Sarah; Brownson, Ross C

2016-01-01

Sustainability has been defined as the existence of structures and processes that allow a program to leverage resources to effectively implement and maintain evidence-based public health and is important in local health departments (LHDs) to retain the benefits of effective programs. Explore the applicability of the Program Sustainability Framework in high- and low-capacity LHDs as defined by national performance standards. Case study interviews from June to July 2013. Standard qualitative methodology was used to code transcripts; codes were developed inductively and deductively. Six geographically diverse LHD's (selected from 3 of high and 3 of low capacity) : 35 LHD practitioners. Thematic reports explored the 8 domains (Organizational Capacity, Program Adaptation, Program Evaluation, Communications, Strategic Planning, Funding Stability, Environmental Support, and Partnerships) of the Program Sustainability Framework. High-capacity LHDs described having environmental support, while low-capacity LHDs reported this was lacking. Both high- and low-capacity LHDs described limited funding; however, high-capacity LHDs reported greater funding flexibility. Partnerships were important to high- and low-capacity LHDs, and both described building partnerships to sustain programming. Regarding organizational capacity, high-capacity LHDs reported better access to and support for adequate staff and staff training when compared with low-capacity LHDs. While high-capacity LHDs described integration of program evaluation into implementation and sustainability, low-capacity LHDs reported limited capacity for measurement specifically and evaluation generally. When high-capacity LHDs described program adoption, they discussed an opportunity to adapt and evaluate. Low-capacity LHDs struggled with programs requiring adaptation. High-capacity LHDs described higher quality communication than low-capacity LHDs. High- and low-capacity LHDs described strategic planning, but high-capacity LHDs reported efforts to integrate evidence-based public health. Investments in leadership support for improving organizational capacity, improvements in communication from the top of the organization, integrating program evaluation into implementation, and greater funding flexibility may enhance sustainability of evidence-based public health in LHDs.

Unusual Mesoporous Carbonaceous Matrix Loading with Sulfur as the Cathode of Lithium Sulfur Battery with Exceptionally Stable High Rate Performance.

PubMed

Qian, Weiwei; Gao, Qiuming; Li, Zeyu; Tian, Weiqian; Zhang, Hang; Zhang, Qiang

2017-08-30

Unusual three-dimensional mesoporous carbon/reduced graphene oxide (MP-C/rGO) matrix possessing graphene nanolayer pore walls built up by three to five graphene monosheets and some carbon particles with the sizes of about 5 nm located between the graphene nanolayers was prepared by facile freeze-drying and then carbonization of the poly(vinyl alcohol) and graphene oxide mixture. The mesoporous carbonaceous MP-C/rGO sample has a high specific surface area of 661.6 m 2 g -1 , large specific pore volume of 1.54 m 3 g -1 , and focused pore size distribution of 2-10 nm. About 64 wt % sulfur could be held in the pores of the MP-C/rGO matrix. As the cathode of a Li-S battery, the MP-C/rGO/S composite showed excellent electrochemical property including a high initial specific capacity of 919 mA h g -1 at 1 C with the capacity retention ratio of 63.3% and the Coulombic efficiency above 90% after 500 cycles. Meanwhile, the initial specific capacity of 602 mA h g -1 at 5 C and remaining capacity of 391 mA h g -1 after 500 cycles with an outstanding Coulombic efficiency of 97% indicate its exceptionally stable rate performance.

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE PAGES

Song, Junhua; Yan, Pengfei; Luo, Langli; ...

2017-09-04

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here in this paper, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb 2O 3 from carbon coated Sb 2O 3 nanoparticlesmore » can accommodate the Sb swelling upon sodiation and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~ 554 mAh g -1, good rate capability (315 mhA g-1 at 10 C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na 0.9[Cu0.22Fe 0.30Mn 0.48]O 2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~ 130 Wh kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0–4.0 V, ~ 1.5 times energy of full-cells with similar design using hard carbon anodes.« less

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Junhua; Yan, Pengfei; Luo, Langli

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb2O3 from carbon coated Sb2O3 nanoparticles can accommodate the Sb swelling upon sodiationmore » and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~554 mAh•g-1, good rate capability (315 mhA•g-1 at 10C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na0.9[Cu0.22Fe0.30Mn0.48]O2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~130 Wh•kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0-4.0 V, ~1.5 times energy of full-cells with similar design using hard carbon anodes.« less

Yolk-shell structured Sb@C anodes for high energy Na-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Song, Junhua; Yan, Pengfei; Luo, Langli

Despite great advances in sodium-ion battery developments, the search for high energy and stable anode materials remains a challenge. Alloy or conversion-typed anode materials are attractive candidates of high specific capacity and low voltage potential, yet their applications are hampered by the large volume expansion and hence poor electrochemical reversibility and fast capacity fade. Here in this paper, we use antimony (Sb) as an example to demonstrate the use of yolk-shell structured anodes for high energy Na-ion batteries. The Sb@C yolk-shell structure prepared by controlled reduction and selective removal of Sb 2O 3 from carbon coated Sb 2O 3 nanoparticlesmore » can accommodate the Sb swelling upon sodiation and improve the structural/electrical integrity against pulverization. It delivers a high specific capacity of ~ 554 mAh g -1, good rate capability (315 mhA g-1 at 10 C rate) and long cyclability (92% capacity retention over 200 cycles). Full-cells of O3-Na 0.9[Cu0.22Fe 0.30Mn 0.48]O 2 cathodes and Sb@C-hard carbon composite anodes demonstrate a high specific energy of ~ 130 Wh kg-1 (based on the total mass of cathode and anode) in the voltage range of 2.0–4.0 V, ~ 1.5 times energy of full-cells with similar design using hard carbon anodes.« less

On the relationship between the specific heat enhancement of salt-based nanofluids and the ionic exchange capacity of nanoparticles.

PubMed

Mondragón, Rosa; Juliá, J Enrique; Cabedo, Luis; Navarrete, Nuria

2018-05-14

Nanoparticles have been used in thermal applications to increase the specific heat of the molten salts used in Concentrated Solar Power plants for thermal energy storage. Although several mechanisms for abnormal enhancement have been proposed, they are still being investigated and more research is necessary. However, this nanoparticle-salt interaction can also be found in chemical applications in which nanoparticles have proved suitable to be used as an adsorbent for nitrate removal given their high specific surface, reactivity and ionic exchange capacity. In this work, the ionic exchange capacity mechanism for the nanoparticles functionalization phenomenon was evaluated. The ionic exchange capacity of silica and alumina nanoparticles dispersed in lithium, sodium and potassium nitrates was measured. Fourier-transform infrared spectroscopy tests confirmed the adsorption of nitrate ions on the nanoparticle surface. A relationship between the ionic exchange capacity of nanoparticles and the specific heat enhancement of doped molten salts was proposed for the first time.

Effect of high energy electron beam (10MeV) on specific heat capacity of low-density polyethylene/hydroxyapatite nano-composite.

PubMed

Soltani, Z; Ziaie, F; Ghaffari, M; Beigzadeh, A M

2017-02-01

In the present work, thermal properties of low density polyethylene (LDPE) and its nano composites are investigated. For this purpose LDPE reinforced with different weight percents of hydroxyapatite (HAP) powder which was synthesized via hydrolysis method are produced. The samples were irradiated with 10MeV electron beam at doses of 75 to 250kGy. Specific heat capacity measurement have been carried out at different temperatures, i.e. 25, 50, 75 and 100°C using modulated temperature differential scanning calorimetry (MTDSC) apparatus and the effect of three parameters include of temperature, irradiation dose and the amount of HAP nano particles as additives on the specific heat capacity of PE/HAP have been investigated precisely. The MTDSC results indicate that the specific heat capacity have decreased by addition of nano sized HAP as reinforcement for LDPE. On the other hand, the effect of radiation dose is reduction in the specific heat capacity in all materials including LDPE and its nano composites. The HAP nano particles along with cross-link junctions due to radiation restrain the movement of the polymer chains in the vicinity of each particle and improve the immobility of polymer chains and consequently lead to reduction in specific heat capacity. Also, the obtained results confirm that the radiation effect on the specific heat capacity is more efficient than the reinforcing effect of nano-sized hydroxyapatite. Copyright © 2016 Elsevier B.V. All rights reserved.

In situ preparation of MgCo2O4 nanosheets on Ni-foam as a binder-free electrode for high performance hybrid supercapacitors.

PubMed

Vijayakumar, Subbukalai; Nagamuthu, Sadayappan; Ryu, Kwang-Sun

2018-05-15

A binder-free, MgCo2O4 nanosheet-like architecture was prepared on Ni-foam using a hydrothermal method. MgCo2O4/Ni-foam was characterized by X-ray diffraction, field emission scanning electron microscopy (FESEM), and transmission electron microscopy techniques. The FESEM image revealed a nanosheet array-like architecture. The MgCo2O4 nanosheets grown on Ni-foam exhibited the maximum specific capacity of 947 C g-1 at a specific current of 2 A g-1. Approximately 96% of the specific capacity was retained from the maximum specific capacity after 5000 continuous charge-discharge cycles. This hybrid device exhibited a maximum specific capacity of 52 C g-1 at a specific current of 0.5 A g-1, and also exhibited a maximum specific energy of 12.99 W h kg-1 at a specific power of 448.7 W kg-1. These results confirmed that the binder-free MgCo2O4 nanosheets grown on Ni-foam are a suitable positive electrode material for hybrid supercapacitors.

Biodiversity of mannose-specific adhesion in Lactobacillus plantarum revisited: strain-specific domain composition of the mannose-adhesin.

PubMed

Gross, G; Snel, J; Boekhorst, J; Smits, M A; Kleerebezem, M

2010-03-01

Recently, we have identified the mannose-specific adhesin encoding gene (msa) of Lactobacillus plantarum. In the current study, structure and function of this potentially probiotic effector gene were further investigated, exploring genetic diversity of msa in L. plantarum in relation to mannose adhesion capacity. The results demonstrate that there is considerable variation in quantitative in vitro mannose adhesion capacity, which is paralleled by msa gene sequence variation. The msa genes of different L. plantarum strains encode proteins with variable domain composition. Construction of L. plantarum 299v mutant strains revealed that the msa gene product is the key-protein for mannose adhesion, also in a strain with high mannose adhering capacity. However, no straightforward correlation between adhesion capacity and domain composition of Msa in L. plantarum could be identified. Nevertheless, differences in Msa sequences in combination with variable genetic background of specific bacterial strains appears to determine mannose adhesion capacity and potentially affects probiotic properties. These findings exemplify the strain-specificity of probiotic characteristics and illustrate the need for careful and molecular selection of new candidate probiotics.

Effects of Cycling Versus Running Training on Sprint and Endurance Capacity in Inline Speed Skating

PubMed Central

Stangier, Carolin; Abel, Thomas; Mierau, Julia; Hollmann, Wildor; Strüder, Heiko K.

2016-01-01

The purpose of this study was to compare the effects of running versus cycling training on sprint and endurance capacity in inline speed skating. Sixteen elite athletes (8 male, 8 female, 24 ± 8 yrs) were randomly assigned into 2 training groups performing either 2 session per week of treadmill running or ergometer cycling in addition to 3 skating specific sessions (technique, plyometrics, parkour) for 8 weeks. Training intensity was determined within non-specific (cycling or running) and effects on specific endurance capacity within a specific incremental exercise test. Before and after the intervention all athletes performed a specific (300m) and one non-specific (30s cycling or 200m running) all-out sprint test according to the group affiliation. To determine the accumulation of blood lactate (BLa) and glucose (BGL) 20 μl arterialized blood was drawn at rest, as well as in 1 min intervals for 10 min after the sprint test. The sport-specific peak oxygen uptake (VO2 peak) was significantly increased (+17%; p = 0.01) in both groups and highly correlated with the sprint performance (r = -0.71). BLa values decreased significantly (-18%, p = 0.02) after the specific sprint test from pre to post-testing without any group effect. However, BGL values only showed a significant decrease (-2%, p = 0.04) in the running group. The close relationship between aerobic capacity and sprint performance in inline speed skating highlights the positive effects of endurance training. Although both training programs were equally effective in improving endurance and sprint capacities, the metabolic results indicate a faster recovery after high intensity efforts for all athletes, as well as a higher reliance on the fat metabolism for athletes who trained in the running group. Key points In addition to a highly developed aerobic performance inline speed skaters also require a highly trained anaerobic capacity to be effective in the sprint sections such as the mass start, tactical attacks and finish line sprint. An 8-week low-intensity endurance training program of either cycling or running training combined with additional routine training improves classical aerobic characteristics (17% increase of VO2 peak), as well as values for acceleration and speed. Athletes who trained in the running group demonstrated a higher reliance on the fat metabolism in the sport-specific post-testing. The significant reduction in anaerobic ATP turnover during repeated sprints appears to be partially compensated by an increase in VO2 in subsequent sprint. The results revealed a close relationship between the aerobic capacity and sprint performance in inline speed skating. PMID:26957925

MoS2 Nanosheets Vertically Grown on Carbonized Corn Stalks as Lithium-Ion Battery Anode.

PubMed

Ma, Luxiang; Zhao, Binglu; Wang, Xusheng; Yang, Junfeng; Zhang, Xinxiang; Zhou, Yuan; Chen, Jitao

2018-06-25

In this study, MoS 2 nanosheets are vertically grown on the inside and outside surfaces of the carbonized corn stalks (CCS) by a simple hydrothermal reaction. The vertically grown structure can not only improve the transmission rate of Li + and electrons but also avoid the agglomeration of the nanosheets. Meanwhile, a new approach of biomass source application is presented. We use CCS instead of graphite powders, which can not only avoid the exploitation of graphite resources, but also be used as a matrix for MoS 2 growth to prevent the electrode from being further decomposed during long cycles and at high current densities. Meanwhile, lithium-ion batteries show remarkable electrochemical performance. They demonstrate a high specific capacity of 1409.5 mA g -1 at 100 mA g -1 in the initial cycle. After 250 cycles, the discharge capacity is still as high as 1230.9 mAh g -1 . Even at 4000 mA g -1 , they show a high specific capacity of 777.7 mAh g -1 . Furthermore, the MoS 2 /CCS electrodes show long cycle life, and the specific capacity is still up to ∼500 mAh g -1 at 5000 mA g -1 after 1000 cycles.

Vertically aligned carbon nanotube electrodes for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Welna, Daniel T.; Qu, Liangti; Taylor, Barney E.; Dai, Liming; Durstock, Michael F.

As portable electronics become more advanced and alternative energy demands become more prevalent, the development of advanced energy storage technologies is becoming ever more critical in today's society. In order to develop higher power and energy density batteries, innovative electrode materials that provide increased storage capacity, greater rate capabilities, and good cyclability must be developed. Nanostructured materials are gaining increased attention because of their potential to mitigate current electrode limitations. Here we report on the use of vertically aligned multi-walled carbon nanotubes (VA-MWNTs) as the active electrode material in lithium-ion batteries. At low specific currents, these VA-MWNTs have shown high reversible specific capacities (up to 782 mAh g -1 at 57 mA g -1). This value is twice that of the theoretical maximum for graphite and ten times more than their non-aligned equivalent. Interestingly, at very high discharge rates, the VA-MWNT electrodes retain a moderate specific capacity due to their aligned nature (166 mAh g -1 at 26 A g -1). These results suggest that VA-MWNTs are good candidates for lithium-ion battery electrodes which require high rate capability and capacity.

THE ELECTRIC CAPACITY OF SUSPENSIONS WITH SPECIAL REFERENCE TO BLOOD.

PubMed

Fricke, H

1925-11-20

1. The specific capacity of a suspension is that capacity which) combined in parallel with a certain resistance, electrically balances 1 cm. cube of the suspension. 2. The following formula holds for the specific capacity of a suspension of spheroids, each of which is composed of a well conducting interior surrounded by a thin membrane of a comparatively high resistance: See PDF for Equation C, specific capacity of suspension; C(o), static capacity of one sq. cm. of membrane; r, r(1) specific resistances respectively of suspension and of suspending liquid; 2 q major axis of spheroid, alpha constant tabulated in Table I. 3. The following formula holds practically for any suspension whatever the form of the suspended particle. See PDF for Equation C = C(100) being the specific capacity of a suspension with a concentration of 100 per cent. Formulae (1a) and (1b) hold only for the case, when the frequency is so low, that the impedance of the static capacity of the membrane around a single particle is high as compared with the resistance of the interior of the particle. The formulae hold also for a suspension of homogeneous particles, when polarization takes place at the surface of each particle, provided the polarization resistance is low as compared with the impedance of the polarization capacity. 4. A description is given of a method for measuring the capacity of a suspension at frequencies between 800 and 4(1/2) million cycles. By means of a specially designed bridge, a substitution method is employed, by which in the last analysis the suspension is compared with the suspending liquid which is so diluted as to have the same specific resistance as the suspension, consecutive measurements being made in the same electrolytic cell. 5. Formula (1b) is verified by measurements of the capacity of suspensions of varying volume concentrations of the red corpuscles of a dog. 6. By means of the above measurements, the value of C(o) is calculated by equation (1a). 7. It is found that C(o) is independent of the frequency up to 4(1/2) million cycles and that it is also independent of the suspending liquid. These results furnish considerable evidence of the validity of the theory, that C(o) represents the static capacity of a corpuscle membrane. 8. On this assumption and using a probable value for the dielectric constant of the membrane, the thickness of the membrane is calculated to be 3.3.10(-7)cm.

Low-Cost High-Energy Potassium Cathode

DOE PAGES

Xue, Leigang; Li, Yutao; Gao, Hongcai; ...

2017-01-26

Potassium has as rich an abundance as sodium in the earth, but the development of a K-ion battery is lagging behind because of the higher mass and larger ionic size of K + than that of Li + and Na +, which makes it difficult to identify a high-voltage and high-capacity intercalation cathode host. Here we propose a cyanoperovskite K xMnFe(CN) 6 (0 ≤ x ≤ 2) as a potassium cathode: high-spin Mn III/Mn II and low-spin Fe III/Fe II couples have similar energies and exhibit two close plateaus centered at 3.6 V; two active K + per formula unitmore » enable a theoretical specific capacity of 156 mAh g -1; Mn and Fe are the two most-desired transition metals for electrodes because they are cheap and environmental friendly. As a powder prepared by an inexpensive precipitation method, the cathode delivers a specific capacity of 142 mAh g -1. Lastly, the observed voltage, capacity, and its low cost make it competitive in large-scale electricity storage applications.« less

One-Dimensional Porous Silicon Nanowires with Large Surface Area for Fast Charge⁻Discharge Lithium-Ion Batteries.

PubMed

Chen, Xu; Bi, Qinsong; Sajjad, Muhammad; Wang, Xu; Ren, Yang; Zhou, Xiaowei; Xu, Wen; Liu, Zhu

2018-04-27

In this study, one-dimensional porous silicon nanowire (1D⁻PSiNW) arrays were fabricated by one-step metal-assisted chemical etching (MACE) to etch phosphorus-doped silicon wafers. The as-prepared mesoporous 1D⁻PSiNW arrays here had especially high specific surface areas of 323.47 m²·g -1 and were applied as anodes to achieve fast charge⁻discharge performance for lithium ion batteries (LIBs). The 1D⁻PSiNWs anodes with feature size of ~7 nm exhibited reversible specific capacity of 2061.1 mAh·g -1 after 1000 cycles at a high current density of 1.5 A·g -1 . Moreover, under the ultrafast charge⁻discharge current rate of 16.0 A·g -1 , the 1D⁻PSiNWs anodes still maintained 586.7 mAh·g -1 capacity even after 5000 cycles. This nanoporous 1D⁻PSiNW with high surface area is a potential anode candidate for the ultrafast charge⁻discharge in LIBs with high specific capacity and superior cycling performance.

Separation and enrichment of trace ractopamine in biological samples by uniformly-sized molecularly imprinted polymers

PubMed Central

Li, Ya; Fu, Qiang; Liu, Meng; Jiao, Yuan-Yuan; Du, Wei; Yu, Chong; Liu, Jing; Chang, Chun; Lu, Jian

2012-01-01

In order to prepare a high capacity packing material for solid-phase extraction with specific recognition ability of trace ractopamine in biological samples, uniformly-sized, molecularly imprinted polymers (MIPs) were prepared by a multi-step swelling and polymerization method using methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as a cross-linker, and toluene as a porogen respectively. Scanning electron microscope and specific surface area were employed to identify the characteristics of MIPs. Ultraviolet spectroscopy, Fourier transform infrared spectroscopy, Scatchard analysis and kinetic study were performed to interpret the specific recognition ability and the binding process of MIPs. The results showed that, compared with other reports, MIPs synthetized in this study showed high adsorption capacity besides specific recognition ability. The adsorption capacity of MIPs was 0.063 mmol/g at 1 mmol/L ractopamine concentration with the distribution coefficient 1.70. The resulting MIPs could be used as solid-phase extraction materials for separation and enrichment of trace ractopamine in biological samples. PMID:29403774

High Performance Li4Ti5O12/Si Composite Anodes for Li-Ion Batteries

PubMed Central

Chen, Chunhui; Agrawal, Richa; Wang, Chunlei

2015-01-01

Improving the energy capacity of spinel Li4Ti5O12 (LTO) is very important to utilize it as a high-performance Li-ion battery (LIB) electrode. In this work, LTO/Si composites with different weight ratios were prepared and tested as anodes. The anodic and cathodic peaks from both LTO and silicon were apparent in the composites, indicating that each component was active upon Li+ insertion and extraction. The composites with higher Si contents (LTO:Si = 35:35) exhibited superior specific capacity (1004 mAh·g−1) at lower current densities (0.22 A·g−1) but the capacity deteriorated at higher current densities. On the other hand, the electrodes with moderate Si contents (LTO:Si = 50:20) were able to deliver stable capacity (100 mAh·g−1) with good cycling performance, even at a very high current density of 7 A·g−1. The improvement in specific capacity and rate performance was a direct result of the synergy between LTO and Si; the former can alleviate the stresses from volumetric changes in Si upon cycling, while Si can add to the capacity of the composite. Therefore, it has been demonstrated that the addition of Si and concentration optimization is an easy yet an effective way to produce high performance LTO-based electrodes for lithium-ion batteries. PMID:28347076

Capacity Evaluations of Psychiatric Patients Requesting Assisted Death in the Netherlands

PubMed Central

Doernberg, Samuel N.; Peteet, John R.; Kim, Scott Y.H.

2016-01-01

Objective Euthanasia or physician-assisted suicide (EAS) of psychiatric patients is legal in some countries but remains controversial. This study examined a frequently raised concern about the practice: how physicians address the issue of decision-making capacity of persons requesting psychiatric EAS. Methods A review of psychiatric EAS case summaries published by the Dutch Regional Euthanasia Review Committees. Directed content analysis using a capacity-specific 4 abilities model (understanding of facts, applying those facts to self, weighing/reasoning, and evidencing choice) was used to code texts discussing capacity. 66 cases from 2011-2014 were reviewed. Results In 55% (36 of 66) of cases the capacity-specific discussion consisted of only global judgments of patients’ capacity, even in patients with psychotic disorders. 32% (21 of 66) of cases included evidentiary statements regarding capacity-specific abilities; only 5 cases (8%) mentioned all four abilities. Physicians frequently stated that psychosis or depression did or did not impact capacity but provided little explanation regarding their judgments. Physicians in 8 cases (12%) disagreed about capacity; even when no explanation is given for the disagreement, the review committees generally accepted the judgment of the physician performing EAS. In one case, the physicians noted that not all capacity-specific abilities were intact but deemed the patient capable. Conclusion Case summaries of psychiatric EAS in the Netherlands do not show that a high threshold of capacity is required for granting EAS. Although this may reflect limitations in documentation, it likely represents a practice that reflects the normative position of the review committees. PMID:27590345

A Class of Organopolysulfides As Liquid Cathode Materials for High-Energy-Density Lithium Batteries.

PubMed

Bhargav, Amruth; Bell, Michaela Elaine; Karty, Jonathan; Cui, Yi; Fu, Yongzhu

2018-06-27

Sulfur-based cathodes are promising to enable high-energy-density lithium-sulfur batteries; however, elemental sulfur as active material faces several challenges, including undesirable volume change (∼80%) when completely reduced and high dependence on liquid electrolyte wherein an electrolyte/sulfur ratio >10 μL mg -1 is required for high material utilization. These limit the attainable energy densities of these batteries. Herein, we introduce a new class of phenyl polysulfides C 6 H 5 S x C 6 H 5 (4 ≤ x ≤ 6) as liquid cathode materials synthesized in a facile and scalable route to mitigate these setbacks. These polysulfides possess sufficiently high theoretical specific capacities, specific energies, and energy densities. Spectroscopic techniques verify their chemical composition and computation shows that the volume change when reduced is about 37%. Lithium half-cell testing shows that phenyl hexasulfide (C 6 H 5 S 6 C 6 H 5 ) can provide a specific capacity of 650 mAh g -1 and capacity retention of 80% through 500 cycles at 1 C rate along with superlative performance up to 10 C. Furthermore, 1302 Wh kg -1 and 1720 Wh L -1 are achievable at a low electrolyte/active material ratio, i.e., 3 μL mg -1 . This work adds new members to the cathode family for Li-S batteries, reduces the gap between the theoretical and practical energy densities of batteries, and provides a new direction for the development of alternative high-capacity cathode materials.

Few-Layer MXenes Delaminated via High-Energy Mechanical Milling for Enhanced Sodium-Ion Batteries Performance.

PubMed

Wu, Yuting; Nie, Ping; Wang, Jiang; Dou, Hui; Zhang, Xiaogang

2017-11-15

The global availability of sodium makes the exploration of superior sodium-ion batteries attractive for energy storage application. MXenes, as one of the most promising anodes for sodium-ion batteries, have been reported to have many advantages, such as high electronic conductivity and a hydrophilic surface. However, the compact multilayer structure and deficient delamination significantly inhibits their application, requiring high energy and showing decreased storage capacity and poor rate capabilities. Few-layer MXene has been proved to benefit superior electrochemical properties with a better ionic conductivity and two-dimensional layer structure. Herein, we report scale delamination of few-layer MXene nanosheets as anodes for sodium-ion batteries, which are prepared via an organic solvent assist high-energy mechanical-milling method. This approach efficiently prevents the oxidation of MXene and produces few-layer nanosheets structure, facilitating fast electron transport and Na + diffusion. Electrochemical tests demonstrate that the few-layer MXenes show high specific capacity, excellent cycle stability, and good rate performance. Specifically, few-layer MXene nanosheets deliver a high reversible capacity of 267 mA h g -1 at a current density of 0.1 A g -1 . After cycling 1500 cycles at a high rate of 1 A g -1 , a reversible capacity of 76 mA h g -1 could be maintained.

Aerosol-assisted chemical vapor deposition of V2O5 cathodes with high rate capabilities for magnesium-ion batteries

NASA Astrophysics Data System (ADS)

Drosos, Charalampos; Jia, Chenglin; Mathew, Shiny; Palgrave, Robert G.; Moss, Benjamin; Kafizas, Andreas; Vernardou, Dimitra

2018-04-01

The growth of orthorhombic vanadium pentoxide nanostructures was accomplished using an aerosol-assisted chemical vapor deposition process. These materials showed excellent electrochemical performance for magnesium-ion storage in an aqueous electrolyte; showing specific discharge capacities of up to 427 mAh g-1 with a capacity retention of 82% after 2000 scans under a high specific current of 5.9 A g-1. The high rate capability suggested good structural stability and high reversibility. We believe the development of low-cost and large-area coating methods, such as the technique used herein, will be essential for the upscalable fabrication of next-generation rechargeable battery technologies.

Gas storage using fullerene based adsorbents

NASA Technical Reports Server (NTRS)

Mikhael, Michael G. (Inventor); Loutfy, Raouf O. (Inventor); Lu, Xiao-Chun (Inventor); Li, Weijiong (Inventor)

2000-01-01

This invention is directed to the synthesis of high bulk density high gas absorption capacity adsorbents for gas storage applications. Specifically, this invention is concerned with novel gas absorbents with high gravimetric and volumetric gas adsorption capacities which are made from fullerene-based materials. By pressing fullerene powder into pellet form using a conventional press, then polymerizing it by subjecting the fullerene to high temperature and high inert gas pressure, the resulting fullerene-based materials have high bulk densities and high gas adsorption capacities. By pre-chemical modification or post-polymerization activation processes, the gas adsorption capacities of the fullerene-based adsorbents can be further enhanced. These materials are suitable for low pressure gas storage applications, such as oxygen storage for home oxygen therapy uses or on-board vehicle natural gas storage. They are also suitable for storing gases and vapors such as hydrogen, nitrogen, carbon dioxide, and water vapor.

Facile Synthesis of Platelike Hierarchical Li1.2Mn0.54Ni0.13Co0.13O2 with Exposed {010} Planes for High-Rate and Long Cycling-Stable Lithium Ion Batteries.

PubMed

Zeng, Jiong; Cui, Yanhui; Qu, Deyang; Zhang, Qian; Wu, Junwei; Zhu, Xiaomeng; Li, Zuohua; Zhang, Xinhe

2016-10-05

Lithium-rich layered oxides are promising cathode candidates for the production of high-energy and high-power electronic devices with high specific capacity and high discharge voltage. However, unstable cycling performance, especially at high charge-recharge rate, is the most challenge issue which needs to be solved to foster the diffusion of these materials. In this paper, hierarchical platelike Li 1.2 Mn 0.54 Ni 0.13 Co 0.13 O 2 cathode materials were synthesized by a facile solvothermal method followed by calcination. Calcination time was found to be a key parameter to obtain pure layered oxide phase and tailor its hierarchical morphology. The Li-rich material consists of primary nanoparticles with exposed {010} planes assembled to form platelike layers which exhibit low resistance to Li + diffusion. In detail, the product by calcination at 900 °C for 12 h exhibits specific capacity of 228, 218, and 204 mA h g -1 at 200, 400, and 1000 mA g -1 , respectively, whereas after 100 cycles at 1000 mA g -1 rate of charge and recharge the specific capacity was retained by about 91%.

3D Interconnected V6O13 Nanosheets Grown on Carbonized Textile via a Seed-Assisted Hydrothermal Process as High-Performance Flexible Cathodes for Lithium-Ion Batteries

NASA Astrophysics Data System (ADS)

Xu, Shixing; Cen, Dingcheng; Gao, Peibo; Tang, Huang; Bao, Zhihao

2018-03-01

Three-dimensional (3D) free-standing nanostructured materials have been proven to be one of the most promising electrodes for energy storage due to their enhanced electrochemical performance. And they are also widely studied for the wearable energy storage systems. In this work, interconnected V6O13 nanosheets were grown on the flexible carbonized textile (c-textile) via a seed-assisted hydrothermal method to form a 3D free-standing electrode for lithium-ion batteries (LIBs). The electrode exhibited a specific capacity of 170 mA h g-1 at a specific current of 300 mA g-1. With carbon nanotube (CNT) coating, its specific capacities further increased 12-40% at the various current rates. It could retain a reversible capacity of 130 mA h g-1, 74% of the initial capacity after 300 cycles at the specific current of 300 mA g-1. It outperformed most of the mixed-valence vanadium oxides. The improved electrochemical performance was ascribed to the synergistic effect of the 3D nanostructure of V6O13 for feasible Li+ diffusion and transport and highly conductive hierarchical conductive network formed by CNT and carbon fiber in c-textile.

Cobalt silicate hierarchical hollow spheres for lithium-ion batteries.

PubMed

Yang, Jun; Guo, Yuanyuan; Zhang, Yufei; Sun, Chencheng; Yan, Qingyu; Dong, Xiaochen

2016-09-09

In this paper, the synthesis of cobalt silicate novel hierarchical hollow spheres via a facile hydrothermal method is presented. With a unique hollow structure, the Co2SiO4 provides a large surface area, which can shorten the lithium ions diffusion length and effectively accommodate the volumetic variation during the lithiation/de-lithiation process. Serving as an anode material in lithium-ion battery application, the Co2SiO4 electrode demonstrates a high reversible specific capacity (first-cycle charge capacity of 948.6 mAh g(-1) at 100 mA g(-1)), a cycling durability (specific capacity of 791.4 mAh g(-1) after 100 cycles at 100 mA g(-1)), and a good rate capability (specific capacity of 349.4 mAh g(-1) at 10 A g(-1)). The results indicate that the cobalt silicate hierarchical hollow sphere holds the potential applications in energy storage electrodes.

Silicon Based Anodes for Li-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhang, Jiguang; Wang, Wei; Xiao, Jie

2012-06-15

Silicon is environmentally benign and ubiquitous. Because of its high specific capacity, it is considered one of the most promising candidates to replace the conventional graphite negative electrode used in today's Li ion batteries. Silicon has a theoretical specific capacity of nearly 4200 mAh/g (Li21Si5), which is 10 times larger than the specific capacity of graphite (LiC6, 372 mAh/g). However, the high capacity of silicon is associated with huge volume changes (more than 300 percent) when alloyed with lithium, which can cause severe cracking and pulverization of the electrode and lead to significant capacity loss. Significant scientific research has beenmore » conducted to circumvent the deterioration of silicon based anode materials during cycling. Various strategies, such as reduction of particle size, generation of active/inactive composites, fabrication of silicon based thin films, use of alternative binders, and the synthesis of 1-D silicon nanostructures have been implemented by a number of research groups. Fundamental mechanistic research has also been performed to better understand the electrochemical lithiation and delithiation process during cycling in terms of crystal structure, phase transitions, morphological changes, and reaction kinetics. Although efforts to date have not attained a commercially viable Si anode, further development is expected to produce anodes with three to five times the capacity of graphite. In this chapter, an overview of research on silicon based anodes used for lithium-ion battery applications will be presented. The overview covers electrochemical alloying of the silicon with lithium, mechanisms responsible for capacity fade, and methodologies adapted to overcome capacity degradation observed during cycling. The recent development of silicon nanowires and nanoparticles with significantly improved electrochemical performance will also be discussed relative to the mechanistic understanding. Finally, future directions on the development of silicon based anodes will be considered.« less

Highly Cyclable Lithium-Sulfur Batteries with a Dual-Type Sulfur Cathode and a Lithiated Si/SiOx Nanosphere Anode.

PubMed

Lee, Sang-Kyu; Oh, Seung-Min; Park, Eunjun; Scrosati, Bruno; Hassoun, Jusef; Park, Min-Sik; Kim, Young-Jun; Kim, Hansu; Belharouak, Ilias; Sun, Yang-Kook

2015-05-13

Lithium-sulfur batteries could become an excellent alternative to replace the currently used lithium-ion batteries due to their higher energy density and lower production cost; however, commercialization of lithium-sulfur batteries has so far been limited due to the cyclability problems associated with both the sulfur cathode and the lithium-metal anode. Herein, we demonstrate a highly reliable lithium-sulfur battery showing cycle performance comparable to that of lithium-ion batteries; our design uses a highly reversible dual-type sulfur cathode (solid sulfur electrode and polysulfide catholyte) and a lithiated Si/SiOx nanosphere anode. Our lithium-sulfur cell shows superior battery performance in terms of high specific capacity, excellent charge-discharge efficiency, and remarkable cycle life, delivering a specific capacity of ∼750 mAh g(-1) over 500 cycles (85% of the initial capacity). These promising behaviors may arise from a synergistic effect of the enhanced electrochemical performance of the newly designed anode and the optimized layout of the cathode.

Sodium vanadium titanium phosphate electrode for symmetric sodium-ion batteries with high power and long lifespan

PubMed Central

Wang, Dongxue; Bie, Xiaofei; Fu, Qiang; Dixon, Ditty; Bramnik, Natalia; Hu, Yong-Sheng; Fauth, Francois; Wei, Yingjin; Ehrenberg, Helmut; Chen, Gang; Du, Fei

2017-01-01

Sodium-ion batteries operating at ambient temperature hold great promise for use in grid energy storage owing to their significant cost advantages. However, challenges remain in the development of suitable electrode materials to enable long lifespan and high rate capability. Here we report a sodium super-ionic conductor structured electrode, sodium vanadium titanium phosphate, which delivers a high specific capacity of 147 mA h g−1 at a rate of 0.1 C and excellent capacity retentions at high rates. A symmetric sodium-ion full cell demonstrates a superior rate capability with a specific capacity of about 49 mA h g−1 at 20 C rate and ultralong lifetime over 10,000 cycles. Furthermore, in situ synchrotron diffraction and X-ray absorption spectroscopy measurement are carried out to unravel the underlying sodium storage mechanism and charge compensation behaviour. Our results suggest the potential application of symmetric batteries for electrochemical energy storage given the superior rate capability and long cycle life. PMID:28660877

Sodium vanadium titanium phosphate electrode for symmetric sodium-ion batteries with high power and long lifespan.

PubMed

Wang, Dongxue; Bie, Xiaofei; Fu, Qiang; Dixon, Ditty; Bramnik, Natalia; Hu, Yong-Sheng; Fauth, Francois; Wei, Yingjin; Ehrenberg, Helmut; Chen, Gang; Du, Fei

2017-06-29

Sodium-ion batteries operating at ambient temperature hold great promise for use in grid energy storage owing to their significant cost advantages. However, challenges remain in the development of suitable electrode materials to enable long lifespan and high rate capability. Here we report a sodium super-ionic conductor structured electrode, sodium vanadium titanium phosphate, which delivers a high specific capacity of 147 mA h g -1 at a rate of 0.1 C and excellent capacity retentions at high rates. A symmetric sodium-ion full cell demonstrates a superior rate capability with a specific capacity of about 49 mA h g -1 at 20 C rate and ultralong lifetime over 10,000 cycles. Furthermore, in situ synchrotron diffraction and X-ray absorption spectroscopy measurement are carried out to unravel the underlying sodium storage mechanism and charge compensation behaviour. Our results suggest the potential application of symmetric batteries for electrochemical energy storage given the superior rate capability and long cycle life.

Biomass-derived carbonaceous positive electrodes for sustainable lithium-ion storage

NASA Astrophysics Data System (ADS)

Liu, Tianyuan; Kavian, Reza; Chen, Zhongming; Cruz, Samuel S.; Noda, Suguru; Lee, Seung Woo

2016-02-01

Biomass derived carbon materials have been widely used as electrode materials; however, in most cases, only electrical double layer capacitance (EDLC) is utilized and therefore, only low energy density can be achieved. Herein, we report on redox-active carbon spheres that can be simply synthesized from earth-abundant glucose via a hydrothermal process. These carbon spheres exhibit a specific capacity of ~210 mA h gCS-1, with high redox potentials in the voltage range of 2.2-3.7 V vs. Li, when used as positive electrode in lithium cells. Free-standing, flexible composite films consisting of the carbon spheres and few-walled carbon nanotubes deliver high specific capacities up to ~155 mA h gelectrode-1 with no obvious capacity fading up to 10 000 cycles, proposing to be promising positive electrodes for lithium-ion batteries or capacitors. Furthermore, considering that the carbon spheres were obtained in an aqueous glucose solution and no toxic or hazardous reagents were used, this process opens up a green and sustainable method for designing high performance, environmentally-friendly energy storage devices.Biomass derived carbon materials have been widely used as electrode materials; however, in most cases, only electrical double layer capacitance (EDLC) is utilized and therefore, only low energy density can be achieved. Herein, we report on redox-active carbon spheres that can be simply synthesized from earth-abundant glucose via a hydrothermal process. These carbon spheres exhibit a specific capacity of ~210 mA h gCS-1, with high redox potentials in the voltage range of 2.2-3.7 V vs. Li, when used as positive electrode in lithium cells. Free-standing, flexible composite films consisting of the carbon spheres and few-walled carbon nanotubes deliver high specific capacities up to ~155 mA h gelectrode-1 with no obvious capacity fading up to 10 000 cycles, proposing to be promising positive electrodes for lithium-ion batteries or capacitors. Furthermore, considering that the carbon spheres were obtained in an aqueous glucose solution and no toxic or hazardous reagents were used, this process opens up a green and sustainable method for designing high performance, environmentally-friendly energy storage devices. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr07064c

High Performance of Supercapacitor from PEDOT:PSS Electrode and Redox Iodide Ion Electrolyte

PubMed Central

Gao, Xing; Zu, Lei; Cai, Xiaomin; Li, Ce; Lian, Huiqin; Liu, Yang; Wang, Xiaodong; Cui, Xiuguo

2018-01-01

Insufficient energy density and poor cyclic stability is still challenge for conductive polymer-based supercapacitor. Herein, high performance electrochemical system has been assembled by combining poly (3,4-ethylenedioxythiophene) (PEDOT):poly (styrene sulfonate) (PSS) redox electrode and potassium iodide redox electrolyte, which provide the maximum specific capacity of 51.3 mAh/g and the retention of specific capacity of 87.6% after 3000 cycles due to the synergic effect through a simultaneous redox reaction both in electrode and electrolyte, as well as the catalytic activity for reduction of triiodide of the PEDOT:PSS. PMID:29772662

The development of a high-capacity instrument module heat transport system, appendixes

NASA Technical Reports Server (NTRS)

1981-01-01

Data sheets provide temperature requirements for 82 individual instruments that are under development or planned for grouping on a space platform or pallet. The scientific objectives of these instrument packages are related to solar physics, space plasma physics, astronomy, high energy astrophysics, resources observations, environmental observations, materials processing, and life sciences. System specifications are given for a high capacity instrument module heat transport system to be used with future payloads.

Carbon felt interlayer derived from rice paper and its synergistic encapsulation of polysulfides for lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Yang, Kai; Zhong, Lei; Guan, Ruiteng; Xiao, Min; Han, Dongmei; Wang, Shuanjin; Meng, Yuezhong

2018-05-01

Lithium-sulfur (Li-S) batteries have remarkably high theoretical specific capacity as promising candidates for next-generation energy storage. However, the "polysulfides shuttle" effect hampers its commercial application. Here, we use a kind of rice paper as a raw material to get inorganic oxides doping carbon felt by the facile carbonization method, and then modified by a simple coating process using poly (fluorenyl ether ketone) and Super P slurry. The special structure of the carbon felt derived from rice paper and its modified layer endow the final electronic conductive interlayer with inherent polysulfides absorbents and ion Coulombic repulsion functions, respectively, which show synergistic effect for trapping polysulfides. As an interlayer of Li-S batteries, the obtained carbon felt/poly (fluorenyl ether ketone)& Super P (CFSS) interlayer shows excellent electrochemical performance in improving specific capacity and decreasing polarization. The batteries with CFSS interlayer exhibit a high capacity of 837 mA h g-1 at 2.0 C and a high initial capacity of 1073.4 mA h g-1 and good capacity retention of 824.5 mA h g-1 after 500 cycles at 0.5 C. CFSS interlayer also shows excellent anti-self-discharge performance. Therefore, the simple and economical CFSS interlayer can be considered as a promising component for high performance Li-S batteries.

High-Capacity Cathode Material with High Voltage for Li-Ion Batteries

DOE PAGES

Shi, Ji -Lei; Xiao, Dong -Dong; Ge, Mingyuan; ...

2018-01-15

Electrochemical energy storage devices with a high energy density are an important technology in modern society, especially for electric vehicles. The most effective approach to improve the energy density of batteries is to search for high-capacity electrode materials. According to the concept of energy quality, a high-voltage battery delivers a highly useful energy, thus providing a new insight to improve energy density. Based on this concept, a novel and successful strategy to increase the energy density and energy quality by increasing the discharge voltage of cathode materials and preserving high capacity is proposed. The proposal is realized in high-capacity Li-richmore » cathode materials. The average discharge voltage is increased from 3.5 to 3.8 V by increasing the nickel content and applying a simple after-treatment, and the specific energy is improved from 912 to 1033 Wh kg-1. The current work provides an insightful universal principle for developing, designing, and screening electrode materials for high energy density and energy quality.« less

High-Capacity Cathode Material with High Voltage for Li-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shi, Ji -Lei; Xiao, Dong -Dong; Ge, Mingyuan

Electrochemical energy storage devices with a high energy density are an important technology in modern society, especially for electric vehicles. The most effective approach to improve the energy density of batteries is to search for high-capacity electrode materials. According to the concept of energy quality, a high-voltage battery delivers a highly useful energy, thus providing a new insight to improve energy density. Based on this concept, a novel and successful strategy to increase the energy density and energy quality by increasing the discharge voltage of cathode materials and preserving high capacity is proposed. The proposal is realized in high-capacity Li-richmore » cathode materials. The average discharge voltage is increased from 3.5 to 3.8 V by increasing the nickel content and applying a simple after-treatment, and the specific energy is improved from 912 to 1033 Wh kg-1. The current work provides an insightful universal principle for developing, designing, and screening electrode materials for high energy density and energy quality.« less

Novel multi-layered 1-D nanostructure exhibiting the theoretical capacity of silicon for a super-enhanced lithium-ion battery

NASA Astrophysics Data System (ADS)

Lee, Byoung-Sun; Yang, Ho-Sung; Jung, Heechul; Jeon, Seung-Yeol; Jung, Changhoon; Kim, Sang-Won; Bae, Jihyun; Choong, Chwee-Lin; Im, Jungkyun; Chung, U.-In; Park, Jong-Jin; Yu, Woong-Ryeol

2014-05-01

Silicon/carbon (Si/C) nanocomposites have recently received much attention as Li-ion battery negative electrodes due to their mutual synergetic effects in capacity and mechanical integrity. The contribution of Si to the total capacity of the Si/C nanocomposites determines their structural efficiency. Herein, we report on a multi-layered, one-dimensional nanostructure that exhibits the theoretical specific capacity of Si in the nanocomposite. Concentrically tri-layered, compartmentalized, C-core/Si-medium/C-shell nanofibers were fabricated by triple coaxial electrospinning. The pulverization of Si was accommodated inside the C-shell, whereas the conductive pathway of the Li-ions and electrons was provided by the C-core, which was proven by ex situ Raman spectroscopy. The compartmentalized Si in between the C-core and C-shell led to excellent specific capacity at a high current rate (>820 mA h g-1 at 12000 mA g-1) and the realization of the theoretical specific capacity of the Li15Si4 phase of Si nanoparticles (3627 mA h g-1). The electrochemical characterization and inductively coupled plasma-atomic emission spectrometry provided direct evidence of full participation of Si in the electrochemical reactions.Silicon/carbon (Si/C) nanocomposites have recently received much attention as Li-ion battery negative electrodes due to their mutual synergetic effects in capacity and mechanical integrity. The contribution of Si to the total capacity of the Si/C nanocomposites determines their structural efficiency. Herein, we report on a multi-layered, one-dimensional nanostructure that exhibits the theoretical specific capacity of Si in the nanocomposite. Concentrically tri-layered, compartmentalized, C-core/Si-medium/C-shell nanofibers were fabricated by triple coaxial electrospinning. The pulverization of Si was accommodated inside the C-shell, whereas the conductive pathway of the Li-ions and electrons was provided by the C-core, which was proven by ex situ Raman spectroscopy. The compartmentalized Si in between the C-core and C-shell led to excellent specific capacity at a high current rate (>820 mA h g-1 at 12000 mA g-1) and the realization of the theoretical specific capacity of the Li15Si4 phase of Si nanoparticles (3627 mA h g-1). The electrochemical characterization and inductively coupled plasma-atomic emission spectrometry provided direct evidence of full participation of Si in the electrochemical reactions. Electronic supplementary information (ESI) available: Simulation details, quantitative measurement of Si content in the nanofibers and ex situ Raman characterization sample preparation procedures are demonstrated. See DOI: 10.1039/c4nr00318g

Fair performance comparison of different carbon blacks in lithium-sulfur batteries with practical mass loadings - Simple design competes with complex cathode architecture

NASA Astrophysics Data System (ADS)

Jozwiuk, Anna; Sommer, Heino; Janek, Jürgen; Brezesinski, Torsten

2015-11-01

The lithium-sulfur system is one of the most promising next generation battery systems, as elemental sulfur is cheap, abundant and has a high theoretical specific capacity. Although much research is conducted on complex sulfur/carbon composites and architectures, it is difficult to compare the performance of the cathodes to one another. Factors, such as different electrolyte composition and cell components strongly affect the cyclability of the battery. Here, we show the importance of optimizing ;standard; conditions to allow for fair performance comparison of different carbon blacks. Our optimal electrolyte-to-sulfur ratio is 11 μL mgsulfur-1 and high concentrations of LiNO3 (>0.6 M) are needed because nitrate is consumed continuously during cycling. Utilizing these standard conditions, we tested the cycling behavior of four types of cathodes with individual carbon blacks having different specific surface areas, namely Printex-A, Super C65, Printex XE-2 and Ketjenblack EC-600JD. Both the specific capacity and polysulfide adsorption capability clearly correlate with the surface area of the carbon being used. High specific capacities (>1000 mAh gsulfur-1 at C/5) are achieved with high surface area carbons. We also demonstrate that a simple cathode using Ketjenblack EC-600JD as the conductive matrix material can well compete with those having complex architectures or additives.

16 CFR Appendix J2 to Part 305 - Pool Heaters-Oil

Code of Federal Regulations, 2014 CFR

2014-01-01

... Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS ENERGY AND WATER USE LABELING FOR CONSUMER PRODUCTS UNDER THE ENERGY POLICY AND CONSERVATION ACT (âENERGY LABELING... heating capacity Range of thermal efficiencies(percent) Low High All capacities * * * No data submitted...

Ammonia adsorption capacity of biomass and animal-manure derived biochars

USDA-ARS?s Scientific Manuscript database

The objective of this research was to characterize and investigate ammonia and hydrogen sulfide gas adsorption capacities of low- and high-temperature biochars made from wood shavings and chicken litter. The biochar samples were activated with steam or phosphoric acid. The specific surface areas and...

Dry-air-stable lithium silicide-lithium oxide core-shell nanoparticles as high-capacity prelithiation reagents.

PubMed

Zhao, Jie; Lu, Zhenda; Liu, Nian; Lee, Hyun-Wook; McDowell, Matthew T; Cui, Yi

2014-10-03

Rapid progress has been made in realizing battery electrode materials with high capacity and long-term cyclability in the past decade. However, low first-cycle Coulombic efficiency as a result of the formation of a solid electrolyte interphase and Li trapping at the anodes, remains unresolved. Here we report LixSi-Li2O core-shell nanoparticles as an excellent prelithiation reagent with high specific capacity to compensate the first-cycle capacity loss. These nanoparticles are produced via a one-step thermal alloying process. LixSi-Li2O core-shell nanoparticles are processible in a slurry and exhibit high capacity under dry-air conditions with the protection of a Li2O passivation shell, indicating that these nanoparticles are potentially compatible with industrial battery fabrication processes. Both Si and graphite anodes are successfully prelithiated with these nanoparticles to achieve high first-cycle Coulombic efficiencies of 94% to >100%. The LixSi-Li2O core-shell nanoparticles enable the practical implementation of high-performance electrode materials in lithium-ion batteries.

Sulfur cathodes with hydrogen reduced titanium dioxide inverse opal structure.

PubMed

Liang, Zheng; Zheng, Guangyuan; Li, Weiyang; Seh, Zhi Wei; Yao, Hongbin; Yan, Kai; Kong, Desheng; Cui, Yi

2014-05-27

Sulfur is a cathode material for lithium-ion batteries with a high specific capacity of 1675 mAh/g. The rapid capacity fading, however, presents a significant challenge for the practical application of sulfur cathodes. Two major approaches that have been developed to improve the sulfur cathode performance include (a) fabricating nanostructured conductive matrix to physically encapsulate sulfur and (b) engineering chemical modification to enhance binding with polysulfides and, thus, to reduce their dissolution. Here, we report a three-dimensional (3D) electrode structure to achieve both sulfur physical encapsulation and polysulfides binding simultaneously. The electrode is based on hydrogen reduced TiO2 with an inverse opal structure that is highly conductive and robust toward electrochemical cycling. The relatively enclosed 3D structure provides an ideal architecture for sulfur and polysulfides confinement. The openings at the top surface allow sulfur infusion into the inverse opal structure. In addition, chemical tuning of the TiO2 composition through hydrogen reduction was shown to enhance the specific capacity and cyclability of the cathode. With such TiO2 encapsulated sulfur structure, the sulfur cathode could deliver a high specific capacity of ∼1100 mAh/g in the beginning, with a reversible capacity of ∼890 mAh/g after 200 cycles of charge/discharge at a C/5 rate. The Coulombic efficiency was also maintained at around 99.5% during cycling. The results showed that inverse opal structure of hydrogen reduced TiO2 represents an effective strategy in improving lithium sulfur batteries performance.

In-situ synthesis of monodisperse micro-nanospherical LiFePO4/carbon cathode composites for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Gong, Hao; Xue, Hairong; Wang, Tao; He, Jianping

2016-06-01

The LiFePO4 is recognized as the promising cathode material, due to its high specific capacity, excellent, structural stability and environmental benignity. However, it is blamed for the low tap density and poor rate performance when served as the cathode materials for a long time. Here, the microspheric LiFePO4/C composites are successfully synthesized through a one-step in-situ solvothermal method combined with carbothermic reduction. These LiFePO4/C microspheres are assembled by LiFePO4 nanoparticles (∼100 nm) and uniformly coated by the carbon, which show a narrow diameter distribution of 4 μm. As a cathode material for lithium ion batteries, the LiFePO4/C composites can deliver an initiate charge capacity of 155 mAh g-1 and retain 90% of initial capacity after 200 cycles at 0.1 C. When cycled at high current densities up to 20 C, it shows a discharge capacity of ∼60 mAh g-1, exhibiting superior rate performance. The significantly improved electrochemical performance of LiFePO4/C composites material can be attributed to its special micro-nano hierarchical structure. Microspheric LiFePO4/C composites exhibit a high tap density about 1.3 g cm-3. What's more, the well-coated carbon insures the high electrical conductivity and the nano-sized LiFePO4/C particles shorten lithium ion transport, thus exhibiting the high specific capacity, high cycling stability and good rate performance.

Determination of thermal physical properties of alkali fluoride/carbonate eutectic molten salt

NASA Astrophysics Data System (ADS)

An, Xue-Hui; Cheng, Jin-Hui; Su, Tao; Zhang, Peng

2017-06-01

Molten salts used in high temperatures are more and more interested in the CSP for higher energy conversion efficiency. Thermal physical properties are the basic engineering data of thermal hydraulic calculation and safety analysis. Therefore, the thermophysical performances involving density, specific heat capacity, viscosity and thermal conductivity of FLiNaK, (LiNaK)2CO3 and LiF(NaK)2CO3 molten salts are experimentally determined and through comparison the general rules can be summarized. Density measurement was performed on the basis of Archimedes theory; specific heat capacity was measured using the DSC technique; viscosity was tested based on the rotating method; and the thermal conductivity was gained by laser flash method with combination of the density, specific heat capacity and thermal diffusivity through a formula. Finally, the energy storage capacity and figures of merit are calculated to evaluate their feasibility as TES and HFT media. The results show that FLiNaK has the largest energy storage capacity and best heat transfer performance, LiF(NaK)2CO3 is secondary, and (LiNaK)2CO3 has the smallest.

Fugitive gas adsorption capacity of biomass and animal-manure derived biochars

USDA-ARS?s Scientific Manuscript database

This research characterized and investigated ammonia and hydrogen sulfide gas adsorption capacities of low- and high-temperature biochars made from wood shavings and chicken litter. The biochar samples were activated with steam or phosphoric acid. The specific surface areas and pore volumes of the a...

Reduced Graphene Oxide-Wrapped FeS2 Composite as Anode for High-Performance Sodium-Ion Batteries

NASA Astrophysics Data System (ADS)

Wang, Qinghong; Guo, Can; Zhu, Yuxuan; He, Jiapeng; Wang, Hongqiang

2018-06-01

Iron disulfide is considered to be a potential anode material for sodium-ion batteries due to its high theoretical capacity. However, its applications are seriously limited by the weak conductivity and large volume change, which results in low reversible capacity and poor cycling stability. Herein, reduced graphene oxide-wrapped FeS2 (FeS2/rGO) composite was fabricated to achieve excellent electrochemical performance via a facile two-step method. The introduction of rGO effectively improved the conductivity, BET surface area, and structural stability of the FeS2 active material, thus endowing it with high specific capacity, good rate capability, as well as excellent cycling stability. Electrochemical measurements show that the FeS2/rGO composite had a high initial discharge capacity of 1263.2 mAh g-1 at 100 mA g-1 and a high discharge capacity of 344 mAh g-1 at 10 A g-1, demonstrating superior rate performance. After 100 cycles at 100 mA g-1, the discharge capacity remained at 609.5 mAh g-1, indicating the excellent cycling stability of the FeS2/rGO electrode.

Stress distribution and pressure-bearing capacity of a high-pressure split-cylinder die with prism cavity

NASA Astrophysics Data System (ADS)

Zhao, Liang; Li, Mingzhe; Wang, Liyan; Qu, Erhu; Yi, Zhuo

2018-03-01

A novel high-pressure belt-type die with a split-type cylinder is investigated with respect to extending its lifetime and improving its pressure bearing capacity. Specifically, a tungsten carbide cylinder is split into several parts along the radial direction with a prism-type cavity. In this paper, the cylinders with different split numbers are chosen to study the stress distribution and compare them with the traditional belt-type die. The simulation results indicate that the split cylinder has much smaller stress than those in the belt-type cylinder, and the statistical analysis reveals that the split-pressure cylinder is able to bear higher pressure. Experimental tests also show that the high-pressure die with a split cylinder and prism cavity has a stronger pressure-bearing capacity than a belt-type die. The split cylinder has advantages of easy manufacturing, high pressure bearing capacity, and replaceable performance.

Laser processing of thick Li(NiMnCo)O2 electrodes for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Rakebrandt, J.-H.; Smyrek, P.; Zheng, Y.; Seifert, H. J.; Pfleging, W.

2017-02-01

Lithium-ion batteries became the most promising types of mobile energy storage devices due to their high gravimetric and volumetric capacity, high cycle life-time, and low self-discharge. Nowadays, the cathode material lithium nickel manganese cobalt oxide (NMC) is one of the most widely used cathode material in commercial lithium-ion batteries due to many advantages such as high energy density (>150 Wh kg-1) on cell level, high power density (650 W kg-1 @ 25 °C and 50 % Depth of Discharge) [1], high specific capacity (163 mAh g-1) [2], high rate capability and good thermal stability in the fully charged state. However, in order to meet the requirements for the increasing demand for rechargeable high energy batteries, nickel-rich NMC electrodes with specific capacities up to 210 mAh g-1 seem to be the next generation cathodes which can reach on cell level desired energy densities higher than 250 Wh kg-1 [3]. Laser-structuring now enables to combine both concepts, high power and high energy lithium-ion batteries. For this purpose, lithium nickel manganese cobalt oxide cathodes were produced via tape casting containing 85-90 wt% of active material with a film thickness of 50-260 μm. The specific capacities were measured using galvanostatic measurements for different types of NMC with varying nickel, manganese and cobalt content at different charging/discharging currents ("C-rates"). An improved lithium-ion diffusion kinetics due to an increased active surface area could be achieved by laser-assisted generating of three dimensional architectures. Cells with unstructured and structured cathodes were compared. Ultrafast laser ablation was used in order to avoid a thermal impact to the material. It was shown that laser structuring of electrode materials leads to a significant improvement in electrochemical performance, especially at high charging and discharging C-rates.

Porous-Nickel-Scaffolded Tin-Antimony Anodes with Enhanced Electrochemical Properties for Li/Na-Ion Batteries.

PubMed

Li, Jiachen; Pu, Jun; Liu, Ziqiang; Wang, Jian; Wu, Wenlu; Zhang, Huigang; Ma, Haixia

2017-08-02

The energy and power densities of rechargeable batteries urgently need to be increased to meet the ever-increasing demands of consumer electronics and electric vehicles. Alloy anodes are among the most promising candidates for next-generation high-capacity battery materials. However, the high capacities of alloy anodes usually suffer from some serious difficulties related to the volume changes of active materials. Porous supports and nanostructured alloy materials have been explored to address these issues. However, these approaches seemingly increase the active material-based properties and actually decrease the electrode-based capacity because of the oversized pores and heavy mass of mechanical supports. In this study, we developed an ultralight porous nickel to scaffold with high-capacity SnSb alloy anodes. The porous-nickel-supported SnSb alloy demonstrates a high specific capacity and good cyclability for both Li-ion and Na-ion batteries. Its capacity retains 580 mA h g -1 at 2 A g -1 after 100 cycles in Li-ion batteries. For a Na-ion battery, the composite electrode can even deliver a capacity of 275 mA h g -1 at 1 A g -1 after 1000 cycles. This study demonstrates that combining the scaffolding function of ultralight porous nickel and the high capacity of the SnSb alloy can significantly enhance the electrochemical performances of Li/Na-ion batteries.

Sulfonic Groups Originated Dual-Functional Interlayer for High Performance Lithium-Sulfur Battery.

PubMed

Lu, Yang; Gu, Sui; Guo, Jing; Rui, Kun; Chen, Chunhua; Zhang, Sanpei; Jin, Jun; Yang, Jianhua; Wen, Zhaoyin

2017-05-03

The lithium-sulfur battery is one of the most prospective chemistries in secondary energy storage field due to its high energy density and high theoretical capacity. However, the dissolution of polysulfides in liquid electrolytes causes the shuttle effect, and the rapid decay of lithium sulfur battery has greatly hindered its practical application. Herein, combination of sulfonated reduced graphene oxide (SRGO) interlayer on the separator is adopted to suppress the shuttle effect. We speculate that this SRGO layer plays two roles: physically blocking the migration of polysulfide as ion selective layer and anchoring lithium polysulfide by the electronegative sulfonic group. Lewis acid-base theory and density functional theory (DFT) calculations indicate that sulfonic groups have a strong tendency to interact with lithium ions in the lithium polysulfide. Hence, the synergic effect involved by the sulfonic group contributes to the enhancement of the battery performance. Furthermore, the uniformly distributed sulfonic groups working as active sites which could induce the uniform distribution of sulfur, alleviating the excessive growth of sulfur and enhancing the utilization of active sulfur. With this interlayer, the prototype battery exhibits a high reversible discharge capacity of more than 1300 mAh g -1 and good capacity retention of 802 mAh g -1 after 250 cycles at 0.5 C rate. After 60 cycles at different rates from 0.2 to 4 C, the cell with this functional separator still recovered a high specific capacity of 1100 mAh g -1 at 0.2 C. The results demonstrate a promising interlayer design toward high performance lithium-sulfur battery with longer cycling life, high specific capacity, and rate capability.

Alloy-Based Anode Materials toward Advanced Sodium-Ion Batteries.

PubMed

Lao, Mengmeng; Zhang, Yu; Luo, Wenbin; Yan, Qingyu; Sun, Wenping; Dou, Shi Xue

2017-12-01

Sodium-ion batteries (SIBs) are considered as promising alternatives to lithium-ion batteries owing to the abundant sodium resources. However, the limited energy density, moderate cycling life, and immature manufacture technology of SIBs are the major challenges hindering their practical application. Recently, numerous efforts are devoted to developing novel electrode materials with high specific capacities and long durability. In comparison with carbonaceous materials (e.g., hard carbon), partial Group IVA and VA elements, such as Sn, Sb, and P, possess high theoretical specific capacities for sodium storage based on the alloying reaction mechanism, demonstrating great potential for high-energy SIBs. In this review, the recent research progress of alloy-type anodes and their compounds for sodium storage is summarized. Specific efforts to enhance the electrochemical performance of the alloy-based anode materials are discussed, and the challenges and perspectives regarding these anode materials are proposed. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ternary tin-based chalcogenide nanoplates as a promising anode material for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Tang, Qiming; Su, Heng; Cui, Yanhui; Baker, Andrew P.; Liu, Yanchen; Lu, Juan; Song, Xiaona; Zhang, Huayu; Wu, Junwei; Yu, Haijun; Qu, Deyang

2018-03-01

As an advanced anode material for lithium-ion batteries, tin-chalcogenides receive substantial attention due to their high lithium-ion storage capacity. Here, tin chalcogenide (SnSe0.5S0.5) nanoplates are synthesized using a facile and quick polyol-method, followed by heating at different temperatures. Results show that the as-prepared of SnSe0.5S0.5 heated at temperature of 180 °C exhibits the best electrochemical performance with an outstanding discharge specific capacity of 1144 mA h g-1 at 0.1 A g-1 after 100 cycles and 682 mA h g-1 at 0.5 A g-1 after 200 cycles with a high coulombic efficiency (CE) of 98.7%. Even at a high current density of 5 A g-1, this anode material delivers a specific capacity of 473 mA h g-1. The high electrochemical performance of SnSe0.5S0.5 is shown by in-situ XRD analysis to originate from an enhanced Li+ intercalation and an alloy conversion process.

Electrospun single crystalline fork-like K2V8O21 as high-performance cathode materials for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Hao, Pengfei; Zhu, Ting; Su, Qiong; Lin, Jiande; Cui, Rong; Cao, Xinxin; Wang, Yaping; Pan, Anqiang

2018-06-01

Single crystalline fork-like potassium vanadate (K2V8O21) has been successfully prepared through electrospinning combined with a subsequent annealing process. The as-obtained K2V8O21 forks show a unique layer-by-layer stacked structure with conductive carbon. When used as cathode materials for lithium-ion batteries, the as-prepared fork-like materials exhibit high specific discharge capacity and excellent cyclic stability. High specific discharge capacity of 200.2 mA h g-1 and 131.5 mA h g-1 can be delivered at the current densities of 50 mA g-1 and 500 mA g-1, respectively. Furthermore, the K2V8O21 electrodes exhibit excellent long-term cycling stability that maintain a capacity of 108.3 mA h g-1 after 300 cycles at 500 mA g-1 with a fading rate of only 0.054% per cycle, revealing their potential applications in next generation high-performance lithium-ion batteries.

Facile Synthesis of Novel Networked Ultralong Cobalt Sulfide Nanotubes and Its Application in Supercapacitors.

PubMed

Liu, Sangui; Mao, Cuiping; Niu, Yubin; Yi, Fenglian; Hou, Junke; Lu, Shiyu; Jiang, Jian; Xu, Maowen; Li, Changming

2015-11-25

Ultralong cobalt sulfide (CoS(1.097)) nanotube networks are synthesized by a simple one-step solvothermal method without any surfactant or template. A possible formation mechanism for the growth processes is proposed. Owing to the hollow structure and large specific area, the novel CoS(1.097) materials present outstanding electrochemical properties. Electrochemical measurements for supercapacitors show that the as-prepared ultralong CoS(1.097) nanotube networks exhibit high specific capacity, good capacity retention, and excellent Coulombic efficiency.

Conductive polymer binder for nano-silicon/graphite composite electrode in lithium-ion batteries towards a practical application

DOE PAGES

Zhao, Hui; Du, Allen; Ling, Min; ...

2016-05-10

The state-of-the-art graphite anode containing a small portion of silicon represents a promising way of applying high-capacity alloy anode in the next generation high energy density lithium-ion batteries. The conductive polymeric binders developed for Si anodes proved to be an effective binder for this graphite/nanoSi composite electrode. Without any acetylene black conductive additives in the electrode, a high areal capacity of above 2.5 mAh/cm 2 is achieved during long-term cycling over 100 cycles. Finally, this conductive polymer-enabled graphite/nanoSi composite electrode exhibits high specific capacity and high 1 st cycle efficiency, which is a significant progress toward commercial application of Simore » anodes.« less

Antibodies attenuate the capacity of dendritic cells to stimulate HIV-specific cytotoxic T lymphocytes

PubMed Central

Posch, Wilfried; Cardinaud, Sylvain; Hamimi, Chiraz; Fletcher, Adam; Mühlbacher, Annelies; Loacker, Klaus; Eichberger, Paul; Dierich, Manfred P.; Pancino, Gianfranco; Lass-Flörl, Cornelia; Moris, Arnaud; Saez-Cirion, Asier; Wilflingseder, Doris

2014-01-01

Background Control of HIV is suggested to depend on potent effector functions of the virus-specific CD8+ T-cell response. Antigen opsonization can modulate the capture of antigen, its presentation, and the priming of specific CD8+ T-cell responses. Objective We have previously shown that opsonization of retroviruses acts as an endogenous adjuvant for dendritic cell (DC)–mediated induction of specific cytotoxic T lymphocytes (CTLs). However, in some HIV-positive subjects, high levels of antibodies and low levels of complement fragments coat the HIV surface. Methods Therefore we analyzed the effect of IgG opsonization on the antigen-presenting capacity of DCs by using CD8+ T-cell proliferation assays after repeated prime boosting, by measuring the antiviral activity against HIV-infected autologous CD4+ T cells, and by determining IFN-γ secretion from HIV-specific CTL clones. Results We find that DCs exposed to IgG-opsonized HIV significantly decreased the HIV-specific CD8+ T-cell response compared with the earlier described efficient CD8+ T-cell activation induced by DCs loaded with complement-opsonized HIV. DCs exposed to HIV bearing high surface IgG levels after incubation in plasma from HIV-infected subjects acted as weak stimulators for HIV-specific CTL clones. In contrast, HIV opsonized with plasma from patients exhibiting high complement and low IgG deposition on the viral surface favored significantly higher activation of HIV-specific CD8+ T-cell clones. Conclusion Our ex vivo and in vitro observations provide the first evidence that IgG opsonization of HIV is associated with a decreased CTL-stimulatory capacity of DCs. PMID:23063584

Endowing CuTCNQ with a new role: a high-capacity cathode for K-ion batteries.

PubMed

Ma, Jing; Zhou, En; Fan, Cong; Wu, Bo; Li, Chao; Lu, Zheng-Hong; Li, Jingze

2018-05-29

Herein, copper-tetracyanoquinodimethane (CuTCNQ) with phase-I kinetics character has been proposed as an effective cathode for potassium-ion batteries. In a voltage range of 2-4.1 V (vs. K+/K), both cuprous cations (Cu+) and organic anions (TCNQ-) are electrochemically active, and they render a three-electron redox mechanism, thereby enabling CuTCNQ to yield a high specific discharge capacity of 244 mA h g-1. Even after 50 cycles, the discharge capacity of 170 mA h g-1 is retained at 50 mA g-1. In addition, when the current density is elevated to 1000 mA g-1, the discharge capacity is still maintained at 125 mA h g-1. These test data are among the best results reported for high-potential cathodes of potassium-ion batteries.

A Heat Vulnerability Index: Spatial Patterns of Exposure, Sensitivity and Adaptive Capacity for Santiago de Chile.

PubMed

Inostroza, Luis; Palme, Massimo; de la Barrera, Francisco

2016-01-01

Climate change will worsen the high levels of urban vulnerability in Latin American cities due to specific environmental stressors. Some impacts of climate change, such as high temperatures in urban environments, have not yet been addressed through adaptation strategies, which are based on poorly supported data. These impacts remain outside the scope of urban planning. New spatially explicit approaches that identify highly vulnerable urban areas and include specific adaptation requirements are needed in current urban planning practices to cope with heat hazards. In this paper, a heat vulnerability index is proposed for Santiago, Chile. The index was created using a GIS-based spatial information system and was constructed from spatially explicit indexes for exposure, sensitivity and adaptive capacity levels derived from remote sensing data and socio-economic information assessed via principal component analysis (PCA). The objective of this study is to determine the levels of heat vulnerability at local scales by providing insights into these indexes at the intra city scale. The results reveal a spatial pattern of heat vulnerability with strong variations among individual spatial indexes. While exposure and adaptive capacities depict a clear spatial pattern, sensitivity follows a complex spatial distribution. These conditions change when examining PCA results, showing that sensitivity is more robust than exposure and adaptive capacity. These indexes can be used both for urban planning purposes and for proposing specific policies and measures that can help minimize heat hazards in highly dynamic urban areas. The proposed methodology can be applied to other Latin American cities to support policy making.

A Heat Vulnerability Index: Spatial Patterns of Exposure, Sensitivity and Adaptive Capacity for Santiago de Chile

PubMed Central

Palme, Massimo; de la Barrera, Francisco

2016-01-01

Climate change will worsen the high levels of urban vulnerability in Latin American cities due to specific environmental stressors. Some impacts of climate change, such as high temperatures in urban environments, have not yet been addressed through adaptation strategies, which are based on poorly supported data. These impacts remain outside the scope of urban planning. New spatially explicit approaches that identify highly vulnerable urban areas and include specific adaptation requirements are needed in current urban planning practices to cope with heat hazards. In this paper, a heat vulnerability index is proposed for Santiago, Chile. The index was created using a GIS-based spatial information system and was constructed from spatially explicit indexes for exposure, sensitivity and adaptive capacity levels derived from remote sensing data and socio-economic information assessed via principal component analysis (PCA). The objective of this study is to determine the levels of heat vulnerability at local scales by providing insights into these indexes at the intra city scale. The results reveal a spatial pattern of heat vulnerability with strong variations among individual spatial indexes. While exposure and adaptive capacities depict a clear spatial pattern, sensitivity follows a complex spatial distribution. These conditions change when examining PCA results, showing that sensitivity is more robust than exposure and adaptive capacity. These indexes can be used both for urban planning purposes and for proposing specific policies and measures that can help minimize heat hazards in highly dynamic urban areas. The proposed methodology can be applied to other Latin American cities to support policy making. PMID:27606592

Working memory capacity and retrieval limitations from long-term memory: an examination of differences in accessibility.

PubMed

Unsworth, Nash; Spillers, Gregory J; Brewer, Gene A

2012-01-01

In two experiments, the locus of individual differences in working memory capacity and long-term memory recall was examined. Participants performed categorical cued and free recall tasks, and individual differences in the dynamics of recall were interpreted in terms of a hierarchical-search framework. The results from this study are in accordance with recent theorizing suggesting a strong relation between working memory capacity and retrieval from long-term memory. Furthermore, the results also indicate that individual differences in categorical recall are partially due to differences in accessibility. In terms of accessibility of target information, two important factors drive the difference between high- and low-working-memory-capacity participants. Low-working-memory-capacity participants fail to utilize appropriate retrieval strategies to access cues, and they also have difficulty resolving cue overload. Thus, when low-working-memory-capacity participants were given specific cues that activated a smaller set of potential targets, their recall performance was the same as that of high-working-memory-capacity participants.

A New Lamination and doping Concepts for Enhanced Li – S Battery Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kumta, Prashant N.; Datta, Moni K.; Velikokhatnyi, Oleg

Lithium ion batteries (LIBs) clearly dominated the area of high-energy storage systems for the past decade with significant research and development activity focused on the development of cathode and anode materials to maximize the specific energy storage, stability, and cycle life of the batteries. However, with the increasing demand in the EV industry for low cost, low weight, and high-energy storage batteries to meet the EV everywhere grand challenge, the current focus of research has shifted towards the development of lithium sulfur batteries (LSB) owing to the high theoretical specific capacity exhibited by sulfur compared to other cathode materials currentlymore » available. Li–S battery shows a theoretical capacity of 1675 mAh/g corresponding to the formation of Li2S which makes sulfur a promising electrode to replace the layered transition metal oxides (~150 mAh/g) and LiFePO4 (~170 mAh/g) hitherto deployed in present LIB systems. Moreover, the abundance of sulfur in the earth’s crust makes it a more economical and highly attractive proposition compared to currently existing cathodes. Despite advantages of sulfur, the existing Li-S battery technology display poor cyclability, low coulombic efficiency (CE) and very low cycle life due to the following issues: 1. Polysulfide (PS) dissolution; 2. Sluggish kinetics of PS to Li2S conversion; 3. High PS diffusivity in the electrolyte; 4. Insulating nature or poor conductivity of sulfur/Li2S; 5. Volumetric expansion/contraction of sulfur; 6. Shuttling of PS along with Li+. These issues result in loss of sulfur causing mechanical disintegration, surface passivation of both anode and cathode, thereby decreasing the specific capacity and columbic efficiency (CE). Present generation sulfur cathodes also show low specific storage capacity, very poor charging rates and low loading densities. Research is needed to overcome the issues impeding Li-S battery technology development.« less

High Aerobic Capacity Mitigates Changes in the Plasma Metabolomic Profile Associated with Aging.

PubMed

Falegan, Oluyemi S; Vogel, Hans J; Hittel, Dustin S; Koch, Lauren G; Britton, Steven L; Hepple, Russ T; Shearer, Jane

2017-02-03

Advancing age is associated with declines in maximal oxygen consumption. Declines in aerobic capacity not only contribute to the aging process but also are an independent risk factor for morbidity, cardiovascular disease, and all-cause mortality. Although statistically convincing, the relationships between aerobic capacity, aging, and disease risk remain largely unresolved. To this end, we employed sensitive, system-based metabolomics approach to determine whether enhanced aerobic capacity could mitigate some of the changes seen in the plasma metabolomic profile associated with aging. Metabolomic profiles of plasma samples obtained from young (13 month) and old (26 month) rats bred for low (LCR) or high (HCR) running capacity using proton nuclear magnetic resonance spectroscopy ( 1 H NMR) were examined. Results demonstrated strong profile separation in old and low aerobic capacity rats, whereas young and high aerobic capacity rat models were less predictive. Significantly differential metabolites between the groups include taurine, acetone, valine, and trimethylamine-N-oxide among other metabolites, specifically citrate, succinate, isovalerate, and proline, were differentially increased in older HCR animals compared with their younger counterparts. When interactions between age and aerobic capacity were examined, results demonstrated that enhanced aerobic capacity could mitigate some but not all age-associated alterations in the metabolomic profile.

Interconnected silicon hollow nanospheres for lithium-ion battery anodes with long cycle life.

PubMed

Yao, Yan; McDowell, Matthew T; Ryu, Ill; Wu, Hui; Liu, Nian; Hu, Liangbing; Nix, William D; Cui, Yi

2011-07-13

Silicon is a promising candidate for the anode material in lithium-ion batteries due to its high theoretical specific capacity. However, volume changes during cycling cause pulverization and capacity fade, and improving cycle life is a major research challenge. Here, we report a novel interconnected Si hollow nanosphere electrode that is capable of accommodating large volume changes without pulverization during cycling. We achieved the high initial discharge capacity of 2725 mAh g(-1) with less than 8% capacity degradation every hundred cycles for 700 total cycles. Si hollow sphere electrodes also show a Coulombic efficiency of 99.5% in later cycles. Superior rate capability is demonstrated and attributed to fast lithium diffusion in the interconnected Si hollow structure.

Li2C2, a High-Capacity Cathode Material for Lithium Ion Batteries.

PubMed

Tian, Na; Gao, Yurui; Li, Yurong; Wang, Zhaoxiang; Song, Xiaoyan; Chen, Liquan

2016-01-11

As a typical alkaline earth metal carbide, lithium carbide (Li2C2) has the highest theoretical specific capacity (1400 mA h g(-1)) among all the reported lithium-containing cathode materials for lithium ion batteries. Herein, the feasibility of using Li2C2 as a cathode material was studied. The results show that at least half of the lithium can be extracted from Li2C2 and the reversible specific capacity reaches 700 mA h g(-1). The C≡C bond tends to rotate to form C4 (C≡C⋅⋅⋅C≡C) chains during lithium extraction, as indicated with the first-principles molecular dynamics (FPMD) simulation. The low electronic and ionic conductivity are believed to be responsible for the potential gap between charge and discharge, as is supported with density functional theory (DFT) calculations and Arrhenius fitting results. These findings illustrate the feasibility to use the alkali and alkaline earth metal carbides as high-capacity electrode materials for secondary batteries. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Overview of space power electronic's technology under the CSTI High Capacity Power Program

NASA Technical Reports Server (NTRS)

Schwarze, Gene E.

1994-01-01

The Civilian Space Technology Initiative (CSTI) is a NASA Program targeted at the development of specific technologies in the areas of transportation, operations and science. Each of these three areas consists of major elements and one of the operation's elements is the High Capacity Power element. The goal of this element is to develop the technology base needed to meet the long duration, high capacity power requirements for future NASA initiatives. The High Capacity Power element is broken down into several subelements that includes energy conversion in the areas of the free piston Stirling power converter and thermoelectrics, thermal management, power management, system diagnostics, and environmental compatibility and system's lifetime. A recent overview of the CSTI High capacity Power element and a description of each of the program's subelements is given by Winter (1989). The goals of the Power Management subelement are twofold. The first is to develop, test, and demonstrate high temperature, radiation-resistant power and control components and circuits that will be needed in the Power Conditioning, Control and Transmission (PCCT) subsystem of a space nuclear power system. The results obtained under this goal will also be applicable to the instrumentation and control subsystem of a space nuclear reactor. These components and circuits must perform reliably for lifetimes of 7-10 years. The second goal is to develop analytical models for use in computer simulations of candidate PCCT subsystems. Circuits which will be required for a specific PCCT subsystem will be designed and built to demonstrate their performance and, also, to validate the analytical models and simulations. The tasks under the Power Management subelement will now be described in terms of objectives, approach and present status of work.

Microwave exfoliated graphene oxide/TiO{sub 2} nanowire hybrid for high performance lithium ion battery

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ishtiaque Shuvo, Mohammad Arif; Rodriguez, Gerardo; Karim, Hasanul

Lithium ion battery (LIB) is a key solution to the demand of ever-improving, high energy density, clean-alternative energy systems. In LIB, graphite is the most commonly used anode material; however, lithium-ion intercalation in graphite is limited, hindering the battery charge rate and capacity. To date, one of the approaches in LIB performance improvement is by using porous carbon (PC) to replace graphite as anode material. PC's pore structure facilitates ion transport and has been proven to be an excellent anode material candidate in high power density LIBs. In addition, to overcome the limited lithium-ion intercalation obstacle, nanostructured anode assembly hasmore » been extensively studied to increase the lithium-ion diffusion rate. Among these approaches, high specific surface area metal oxide nanowires connecting nanostructured carbon materials accumulation have shown promising results for enhanced lithium-ion intercalation. Herein, we demonstrate a hydrothermal approach of growing TiO{sub 2} nanowires (TON) on microwave exfoliated graphene oxide (MEGO) to further improve LIB performance over PC. This MEGO-TON hybrid not only uses the high surface area of MEGO but also increases the specific surface area for electrode–electrolyte interaction. Therefore, this new nanowire/MEGO hybrid anode material enhances both the specific capacity and charge–discharge rate. Scanning electron microscopy and X-ray diffraction were used for materials characterization. Battery analyzer was used for measuring the electrical performance of the battery. The testing results have shown that MEGO-TON hybrid provides up to 80% increment of specific capacity compared to PC anode.« less

High-Temperature Electrochemical Performance of FeF3/C Nanocomposite as a Cathode Material for Lithium-Ion Batteries

NASA Astrophysics Data System (ADS)

Tang, Mengyun; Zhang, Zhengfu; Wang, Zi; Liu, Jingfeng; Yan, Hongge; Peng, Jinhui

2018-02-01

Iron trifluoride has been studied as a cathode material due to its cost-effectiveness, low toxicity, and high theoretical capacities of 712 mA h g-1. However, FeF3 has serious shortcomings of poor electronic conductivity and a slow diffusion rate of lithium ions, leading to a lower reversible specific capacity. In this work, FeF3/C nanocomposite has been synthesized successfully via a high-energy ball-milling method, and acetylene black is used as the conductive agent to improve the conductivity of FeF3. The FeF3/C nanocomposite shows a high initial discharge capacity of 346.25 and 161.58 mA h g-1 after 40th cycle at 50 mA g-1. It exhibits good cycle performance and rate performance. The high-temperature discharge capacities decreased with increase in the temperature. The initial high-temperature discharge capacities are found to be 254.17, 300.01, 281.25 and 125.16, and 216.875, 156, 141.67, 150, and 64.98 mA h g-1 at 20th cycles at the 40, 50, 60, and 70 °C, respectively.

Examining variation in working memory capacity and retrieval in cued recall.

PubMed

Unsworth, Nash

2009-05-01

Two experiments examined the notion that individual differences in working memory capacity (WMC) are partially due to differences in search set size in cued recall. High and low WMC individuals performed variants of a cued recall task with either unrelated cue words (Experiment 1) or specific cue phrases (Experiment 2). Across both experiments low WMC individuals recalled fewer items, made more errors, and had longer correct recall latencies than high WMC individuals. Cross-experimental analyses suggested that providing participants with more specific cues decreased the size of the search set, leading to better recall overall. However, these effects were equivalent for high and low WMC. It is argued that these results are consistent with a search model framework in which low WMC individuals search through a larger set of items than high WMC individuals.

Carbon-Coated, Diatomite-Derived Nanosilicon as a High Rate Capable Li-ion Battery Anode.

PubMed

Campbell, Brennan; Ionescu, Robert; Tolchin, Maxwell; Ahmed, Kazi; Favors, Zachary; Bozhilov, Krassimir N; Ozkan, Cengiz S; Ozkan, Mihrimah

2016-10-07

Silicon is produced in a variety of ways as an ultra-high capacity lithium-ion battery (LIB) anode material. The traditional carbothermic reduction process required is expensive and energy-intensive; in this work, we use an efficient magnesiothermic reduction to convert the silica-based frustules within diatomaceous earth (diatomite, DE) to nanosilicon (nanoSi) for use as LIB anodes. Polyacrylic acid (PAA) was used as a binder for the DE-based nanoSi anodes for the first time, being attributed for the high silicon utilization under high current densities (up to 4C). The resulting nanoSi exhibited a high BET specific surface area of 162.6 cm 2 g -1 , compared to a value of 7.3 cm 2 g -1 for the original DE. DE contains SiO 2 architectures that make ideal bio-derived templates for nanoscaled silicon. The DE-based nanoSi anodes exhibit good cyclability, with a specific discharge capacity of 1102.1 mAh g -1 after 50 cycles at a C-rate of C/5 (0.7 A g Si -1 ) and high areal loading (2 mg cm -2 ). This work also demonstrates the fist rate capability testing for a DE-based Si anode; C-rates of C/30 - 4C were tested. At 4C (14.3 A g Si -1 ), the anode maintained a specific capacity of 654.3 mAh g -1 - nearly 2x higher than graphite's theoretical value (372 mAh g -1 ).

Fabrication and Performance of High Energy Li-Ion Battery Based on the Spherical Li[Li(0.2)Ni(0.16)Co(0.1)Mn(0.54)]O2 Cathode and Si Anode.

PubMed

Ye, Jing; Li, Yi-xuan; Zhang, Li; Zhang, Xue-ping; Han, Min; He, Ping; Zhou, Hao-shen

2016-01-13

The cathode materials of Li-ion batteries for electric vehicles require not only a large gravimetric capacity but also a high volumetric capacity. A new Li-rich layered oxide cathode with superior capacity, Li[Li0.20Ni0.16Co0.10Mn0.54]O2 (denoted as LNCM), is synthesized from precursor, a coprecipitated spherical metal hydroxide. The preparation technology of precursor such as stirring speed, concentration of metal solution, and reaction time are regulated elaborately. The final product LNCM shows a well-ordered, hexagonal-layer structure, as confirmed by Rietveld refinement of X-ray diffraction pattern. The particle size of the final product has an average diameter of about 10 μm, and the corresponding tap density is about 2.25 g cm(-3). Electrochemical measurements indicate that as-prepared LNCM has great initial columbic efficiency, reversible capacity, and cycling stability, with specific discharge capacities of 278 and 201 mAh g(-1) at 0.03 and 0.5 C rates, respectively. Cycling at 0.1 C, LNCM delivers a discharge capacity of 226 mAh g(-1) with 95% retention capacity after 50 cycles. Si/LNCM cell is fabricated using Si submicroparticle as anode against LNCM. The cell can exhibit a specific energy of 590 Wh kg(-1) based on the total weight of cathode and anode materials.

Phenolics and antioxidant capacity of table grape (Vitis vinifera L.) cultivars grown in Chile.

PubMed

Lutz, Mariane; Jorquera, Katterin; Cancino, Beatriz; Ruby, Rene; Henriquez, Carolina

2011-09-01

Grapes (Vitis vinifera L.) possess health-promoting effects attributed to their supply of a wide variety of bioactive phenolics. Juice and skin fractions of 4 varieties of table grapes: Red Globe, Crimson Seedless, Autumn Royal, and Ribier were prepared to determine and compare their total phenolics content, antioxidant capacity (DPPH, FRAP, and ORAC), anthocyanins, and specific phenolics (caffeic acid, gallic acid, resveratrol, and catechin) content, since a series of positive health benefits are expected from the intake of any of these fractions. Higher amounts of total phenolics and antioxidant capacity were observed in the skin fractions (P < 0.05). Blue grapes (Autumn Royal and Ribier) exhibited higher phenolics content and antioxidant capacity (P < 0.05) than red grapes. The most abundant phenolic compound observed was catechin (P < 0.05). Significant correlations between the antioxidant capacity and total phenolics were observed in grape juice and skin fractions. Autumn Royal juice provides a very high amount of phenolics, anthocyanins, and exhibits the highest antioxidant capacity, offering the best health promoting properties compared with the other grape varieties studied. Grapes possess health-promoting effects attributed to their supply of a wide variety of bioactive phenolics. Grape juice made with blue grapes (Autumn Royal, Ribier) exhibit higher phenolics content and antioxidant capacity than juice elaborated with red grapes (Red Globe, Crimson Seedless). The skin is a good source of phenolics and has a high antioxidant capacity. Specific health-promoting phenolics are more abundant in blue grapes, mainly in their skin fraction, which should not be discarded. © 2011 Institute of Food Technologists®

Modular operation of membrane bioreactors for higher hydraulic capacity utilisation.

PubMed

Veltmann, K; Palmowski, L M; Pinnekamp, J

2011-01-01

Using data from 6 full-scale municipal membrane bioreactors (MBR) in Germany the hydraulic capacity utilisation and specific energy consumption were studied and their connexion shown. The average hydraulic capacity utilisation lies between 14% and 45%. These low values are justified by the necessity to deal with intense rain events and cater for future flow increases. However, this low hydraulic capacity utilisation leads to high specific energy consumption. The optimisation of MBR operation requires a better utilisation of MBR hydraulic capacity, particularly under consideration of the energy-intensive membrane aeration. A first approach to respond to large influent flow fluctuations consists in adjusting the number of operating modules. This is practised by most MBR operators but so far mostly with variable flux and constant membrane aeration. A second approach is the real-time adjustment of membrane aeration in line with flux variations. This adjustment is not permitted under current manufacturers' warranty conditions. A further opportunity is a discontinuous operation, in which filtration takes place over short periods at high flux and energy for membrane aeration is saved during filtration pauses. The integration of a buffer volume is thereby indispensable. Overall a modular design with small units, which can be activated/ inactivated according to the influent flow and always operate under optimum conditions, enables a better utilisation of MBR hydraulic capacity and forms a solid base to reduce MBR energy demand.

Self-Supported CoP Nanorod Arrays Grafted on Stainless Steel as an Advanced Integrated Anode for Stable and Long-Life Lithium-Ion Batteries.

PubMed

Xu, Xijun; Liu, Jun; Hu, Renzong; Liu, Jiangwen; Ouyang, Liuzhang; Zhu, Min

2017-04-19

To alleviate the capacity degradation of anode materials for Li-ion batteries, caused by serious volume expansion and particle aggregation, intensive attention has been devoted to the rational design and fabrication of novel anode architectures. Herein, self-supported CoP nanorod arrays have been facilely synthesized using hydrothemally deposited Co(CO 3 ) 0.5 (OH)⋅0.11 H 2 O nanorod arrays as the precursor, through a gas-phase phosphidation method. As the anode for Li-ion batteries, such 3D interconnected CoP nanorod arrays show an initial discharge capacity of 1067 mAh g -1 and a high reversible charge capacity of 737 mAh g -1 at 0.4 Ag -1 . After 400 cycles, their specific capacity can reach 510 mAh g -1 ; even after 900 cycles, they can still deliver a specific capacity of 390 mAh g -1 . CoP//LiCoO 2 full-cells also exhibit a high reversible capacity of 400 mAh g -1 after 50 cycles. These unique 3D interconnected CoP nanorod arrays also show ultrastable cycling performance over 500 cycles when used as the anode in a Na-ion battery. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Polypyrrole-encapsulated vanadium pentoxide nanowires on a conductive substrate for electrode in aqueous rechargeable lithium battery.

PubMed

Liang, Chaowei; Fang, Dong; Cao, Yunhe; Li, Guangzhong; Luo, Zhiping; Zhou, Qunhua; Xiong, Chuanxi; Xu, Weilin

2015-02-01

Precursors of ammonium vanadium bronze (NH4V4O10) nanowires assembled on a conductive substrate were prepared by a hydrothermal method. After calcination at 360°C, the NH4V4O10 precursor transformed to vanadium pentoxide (V2O5) nanowires, which presented a high initial capacity of 135.0mA h g(-1) at a current density of 50mA g(-1) in 5M LiNO3 aqueous solution; while the specific capacity faded quickly over 50 cycles. By coating the surface of V2O5 nanowires with water-insoluble polypyrrole (PPy), the formed nanocomposite electrode exhibited a specific discharge capacity of 89.9mA h g(-1) at 50mA g(-1) (after 100 cycles). A V2O5@PPy //LiMn2O4 rechargeable lithium battery exhibited an initial discharge capacity of 95.2mA h g(-1); and after 100 cycles, a specific discharge capacity of 81.5mA h g(-1) could retain at 100mA g(-1). Copyright © 2014 Elsevier Inc. All rights reserved.

Advanced Sulfur Cathode Enabled by Highly Crumpled Nitrogen-Doped Graphene Sheets for High-Energy-Density Lithium-Sulfur Batteries.

PubMed

Song, Jiangxuan; Yu, Zhaoxin; Gordin, Mikhail L; Wang, Donghai

2016-02-10

Herein, we report a synthesis of highly crumpled nitrogen-doped graphene sheets with ultrahigh pore volume (5.4 cm(3)/g) via a simple thermally induced expansion strategy in absence of any templates. The wrinkled graphene sheets are interwoven rather than stacked, enabling rich nitrogen-containing active sites. Benefiting from the unique pore structure and nitrogen-doping induced strong polysulfide adsorption ability, lithium-sulfur battery cells using these wrinkled graphene sheets as both sulfur host and interlayer achieved a high capacity of ∼1000 mAh/g and exceptional cycling stability even at high sulfur content (≥80 wt %) and sulfur loading (5 mg sulfur/cm(2)). The high specific capacity together with the high sulfur loading push the areal capacity of sulfur cathodes to ∼5 mAh/cm(2), which is outstanding compared to other recently developed sulfur cathodes and ideal for practical applications.

Characterization and Thermal Properties of Nitrate Based Molten Salt for Heat Recovery System

NASA Astrophysics Data System (ADS)

Faizal Tukimon, Mohd; Muhammad, Wan Nur Azrina Wan; Nor Annuar Mohamad, Md; Yusof, Farazila

2017-10-01

Molten salt can acts like a storage medium or heat transfer fluid in heat recovery system. Heat transfer fluid is a fluid that has the capability to deliver heat this one side to another while heat recovery system is a system that transfers heat to produce energy. This studies shows about determining the new formulation of different molten nitrate/nitrite salts consisting of LiNO3, KNO2, KNO3 and NaNO2 that give a low temperature of melting point and high average specific heat capacity. Mixed alkaline molten nitrate/nitrite salt can act as a heat transfer fluid due to their advantageous in terms of its properties that feasible in heat recovery system such as high specific heat capacity, low vapour pressure, low cost and wide range of temperature in its application. The mixing of these primary substances will form a new line of quaternary nitrate salt (LiNO3 - KNO2 - KNO3 - NaNO2). The quaternary mixture was heated inside the box furnace at 150°C for four hours and rose up the temperature to 400°C for eight hours to homogenize the mixture. Through heating process, the elements of nitrate/nitrite base were mixed completely. The temperature was then reduced to 115°C for several hours before removing the mixture from the furnace. The melting point of each sample were testified by using thermal gravimetric analysis, TGA/DTA and experiment of determining the specific heat capacity were conducted by using Differential Scanning Calorimeter, DSC. From the result, it is found that the melting point Sample 1 with percentage of weightage (25.4wt% of LiNO3, 33.8wt% of KNO2, 20.7wt% of KNO3 and 20.1wt% of NaNO2) is 94.4°C whereas the average specific heat capacity was 1.0484/g°C while for Sample 3 with percentages of weightage (30.0wt% of LiNO3, 50.2wt% of KNO2, 3.1wt% of KNO3 and 16.7wt% of NaNO2), the melting point is 86.1°C with average specific heat capacity of 0.7274 J/g°C. In the nut shell, the quaternary mixture salts had been a good mixture with good thermal properties that low in melting point and have high specific heat capacity which could be a potential heat transfer fluid in heat recovery application.

Electrochemical properties of high-power supercapacitors using ordered NiO coated Si nanowire array electrodes

NASA Astrophysics Data System (ADS)

Lu, Fang; Qiu, Mengchun; Qi, Xiang; Yang, Liwen; Yin, Jinjie; Hao, Guolin; Feng, Xiang; Li, Jun; Zhong, Jianxin

2011-08-01

Highly ordered NiO coated Si nanowire arrays are fabricated as electrode materials for electrochemical supercapacitors (ES) via depositing Ni on electroless-etched Si nanowires and subsequently annealing. The electrochemical tests reveal that the constructed electrode has superior electrical conductibility and more active sites per unit area for chemical reaction processes, thereby possessing good cycle stability, high specific capacity, and low internal resistance. The specific capacity is up to 787.5 F g-1 at a discharge current of 2.5 mA and decreases slightly with 4.039% loss after 500 cycles, while the equivalent internal resistance is ˜3.067 Ω. Owing to its favorable electrochemical performance, this ordered hybrid array nanostructure is a promising electrode material in future commercial ES.

Scalable and template-free synthesis of nanostructured Na{sub 1.08}V{sub 6}O{sub 15} as high-performance cathode material for lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Shili, E-mail: slzheng@ipe.ac.cn; Wang, Xinran; Yan, Hong

2016-09-15

Highlights: • Nanostructured Na{sub 1.08}V{sub 6}O{sub 15} was synthesized through additive-free sol-gel process. • Prepared Na{sub 1.08}V{sub 6}O{sub 15} demonstrated high capacity and sufficient cycling stability. • The reaction temperature was optimized to allow scalable Na{sub 1.08}V{sub 6}O{sub 15} fabrication. - Abstract: Developing high-capacity cathode material with feasibility and scalability is still challenging for lithium-ion batteries (LIBs). In this study, a high-capacity ternary sodium vanadate compound, nanostructured NaV{sub 6}O{sub 15}, was template-free synthesized through sol-gel process with high producing efficiency. The as-prepared sample was systematically post-treated at different temperature and the post-annealing temperature was found to determine the cycling stabilitymore » and capacity of NaV{sub 6}O{sub 15}. The well-crystallized one exhibited good electrochemical performance with a high specific capacity of 302 mAh g{sup −1} when cycled at current density of 0.03 mA g{sup −1}. Its relatively long-term cycling stability was characterized by the cell performance under the current density of 1 A g{sup −1}, delivering a reversible capacity of 118 mAh g{sup −1} after 300 cycles with 79% capacity retention and nearly 100% coulombic efficiency: all demonstrating its significant promise of proposed strategy for large-scale synthesis of NaV{sub 6}O{sub 15} as cathode with high-capacity and high energy density for LIBs.« less

Automotive assessment of carbon-silicon composite anodes and methods of fabrication

NASA Astrophysics Data System (ADS)

Karulkar, Mohan; Blaser, Rachel; Kudla, Bob

2015-01-01

To assess the potential of carbon silicon composite anodes for automotive applications, C-Si anodes were fabricated and certain improvements employed. The use of a PVDF buffer layer is demonstrated for the first time with a C-Si composite material. The buffer layer increases adhesion by 89%, and increases capacity by 50-80%. Also, a limited capacity range is employed to improve cycle life by up to 200%, and enable currents as high as 2 mA cm-1. The combined use of a buffer layer and limited capacity range has not been reported before. A model is also presented for comparing C-Si performance with real-world automotive targets from USABC, including energy density, power density, specific energy, and specific power. The analysis reveals a capacity penalty that arises from pairing C-Si with a traditional cathode (NCA), and which prevents the cell from meeting all targets. Scenarios are presented in which a higher-capacity cathode (250 mAh g-1) allows all targets to be hypothetically met.

Nanoconfined phosphorus film coating on interconnected carbon nanotubes as ultrastable anodes for lithium ion batteries

NASA Astrophysics Data System (ADS)

Xu, Zhiwei; Zeng, Yan; Wang, Liyuan; Li, Nan; Chen, Cheng; Li, Cuiyu; Li, Jing; Lv, Hanming; Kuang, Liyun; Tian, Xu

2017-07-01

Elemental phosphorus (P) is extensively explored as promising anode candidates due to its abundance, low-cost and high theoretical specific capacity. However, it is of great challenge for P-based materials as practical high-energy-density and long-cycling anodes for its large volume expansion and low conductibility. Here, we significantly improve both cycling and rate performance of red P by cladding the nanoconfined P film on interconnected multi-walled carbon nanotube networks (P-MWCNTs composite) via facile wet ball-milling. The red P-MWCNTs anode presents a superior high reversible capacity of 1396.6 mAh g-1 on the basis of P-MWCNTs composite weight at 50 mA g-1 with capacity retention reaching at ∼90% over 50 cycles. Even at 1000 mA g-1, it still maintains remarkable specific reversible capacity of 934.0 mAh g-1. This markedly enhanced performance is ascribed to synergistic advantages of this unique structure: Intimate contacts between nanosized red P and entangled MWCNTs not only shorten the transmission routes of ions through MWCNTs toward red P, but also motivate the access with electrolyte to open structures of P film. Besides, the confined nanosized P film moderate volume expansions effectively and the entangled MWCNTs networks acted as conductive channels activate high ionic/electronic conductivity of the whole electrodes.

Hierarchical network architectures of carbon fiber paper supported cobalt oxide nanonet for high-capacity pseudocapacitors.

PubMed

Yang, Lei; Cheng, Shuang; Ding, Yong; Zhu, Xingbao; Wang, Zhong Lin; Liu, Meilin

2012-01-11

We present a high-capacity pseudocapacitor based on a hierarchical network architecture consisting of Co(3)O(4) nanowire network (nanonet) coated on a carbon fiber paper. With this tailored architecture, the electrode shows ideal capacitive behavior (rectangular shape of cyclic voltammograms) and large specific capacitance (1124 F/g) at high charge/discharge rate (25.34 A/g), still retaining ~94% of the capacitance at a much lower rate of 0.25 A/g. The much-improved capacity, rate capability, and cycling stability may be attributed to the unique hierarchical network structures, which improves electron/ion transport, enhances the kinetics of redox reactions, and facilitates facile stress relaxation during cycling. © 2011 American Chemical Society

An original approach was used to better evaluate the capacity of a prognostic marker using published survival curves.

PubMed

Dantan, Etienne; Combescure, Christophe; Lorent, Marine; Ashton-Chess, Joanna; Daguin, Pascal; Classe, Jean-Marc; Giral, Magali; Foucher, Yohann

2014-04-01

Predicting chronic disease evolution from a prognostic marker is a key field of research in clinical epidemiology. However, the prognostic capacity of a marker is not systematically evaluated using the appropriate methodology. We proposed the use of simple equations to calculate time-dependent sensitivity and specificity based on published survival curves and other time-dependent indicators as predictive values, likelihood ratios, and posttest probability ratios to reappraise prognostic marker accuracy. The methodology is illustrated by back calculating time-dependent indicators from published articles presenting a marker as highly correlated with the time to event, concluding on the high prognostic capacity of the marker, and presenting the Kaplan-Meier survival curves. The tools necessary to run these direct and simple computations are available online at http://www.divat.fr/en/online-calculators/evalbiom. Our examples illustrate that published conclusions about prognostic marker accuracy may be overoptimistic, thus giving potential for major mistakes in therapeutic decisions. Our approach should help readers better evaluate clinical articles reporting on prognostic markers. Time-dependent sensitivity and specificity inform on the inherent prognostic capacity of a marker for a defined prognostic time. Time-dependent predictive values, likelihood ratios, and posttest probability ratios may additionally contribute to interpret the marker's prognostic capacity. Copyright © 2014 Elsevier Inc. All rights reserved.

Visual attention capacity: a review of TVA-based patient studies.

PubMed

Habekost, Thomas; Starrfelt, Randi

2009-02-01

Psychophysical studies have identified two distinct limitations of visual attention capacity: processing speed and apprehension span. Using a simple test, these cognitive factors can be analyzed by Bundesen's Theory of Visual Attention (TVA). The method has strong specificity and sensitivity, and measurements are highly reliable. As the method is theoretically founded, it also has high validity. TVA-based assessment has recently been used to investigate a broad range of neuropsychological and neurological conditions. We present the method, including the experimental paradigm and practical guidelines to patient testing, and review existing TVA-based patient studies organized by lesion anatomy. Lesions in three anatomical regions affect visual capacity: The parietal lobes, frontal cortex and basal ganglia, and extrastriate cortex. Visual capacity thus depends on large, bilaterally distributed anatomical networks that include several regions outside the visual system. The two visual capacity parameters are functionally separable, but seem to rely on largely overlapping brain areas.

Changes in Acceleration and Deceleration Capacity Throughout Professional Soccer Match-Play.

PubMed

Russell, Mark; Sparkes, William; Northeast, Jonny; Cook, Christian J; Love, Tom D; Bracken, Richard M; Kilduff, Liam P

2016-10-01

Russell, M, Sparkes, W, Northeast, J, Cook, CJ, Love, TD, Bracken, RM, and Kilduff, LP. Changes in acceleration and deceleration capacity throughout professional soccer match-play. J Strength Cond Res 30(10): 2839-2844, 2016-As the acceleration and deceleration demands of soccer are currently not well understood, this study aimed to profile markers of acceleration and deceleration capacity during professional soccer match-play. This within-player observational study required reserve team players from a Premier League club to wear 10-Hz Global Positioning System units throughout competitive matches played in the 2013-14 competitive season. Data are presented for players who completed 4 or more games during the season (n = 11), and variables are presented according to six 15-minute intervals (I1-6: 00:00-14:59 minutes, 15:00-29:59 minutes, 30:00-44:59 minutes, 45:00-59:59 minutes, 60:00-74:59 minutes, and 75:00-89:59 minutes, respectively). During I6, the distance covered (total, per minute, and at high intensity), number of sprints, accelerations (total and high intensity), decelerations (total and high intensity), and impacts were reduced compared with I1 (all p ≤ 0.05). The number of high-intensity impacts remained unchanged throughout match-play (p > 0.05). These findings indicate that high-intensity actions and markers of acceleration and deceleration capacity are reduced in the last 15 minutes of the normal duration of match-play. Such information can be used to increase the specificity of training programs designed for soccer players while also giving further insight in to the effects of 90 minutes of soccer-specific exercise. Interventions that seek to maintain the acceleration and deceleration capacity of players throughout the full duration of a soccer match warrant investigation.

High rate, long cycle life battery electrode materials with an open framework structure

DOEpatents

Wessells, Colin; Huggins, Robert; Cui, Yi; Pasta, Mauro

2015-02-10

A battery includes a cathode, an anode, and an aqueous electrolyte disposed between the cathode and the anode and including a cation A. At least one of the cathode and the anode includes an electrode material having an open framework crystal structure into which the cation A is reversibly inserted during operation of the battery. The battery has a reference specific capacity when cycled at a reference rate, and at least 75% of the reference specific capacity is retained when the battery is cycled at 10 times the reference rate.

High-rate and ultralong cycle-life LiFePO4 nanocrystals coated by boron-doped carbon as positive electrode for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Feng, Jinpeng; Wang, Youlan

2016-12-01

An evolutionary modification approach, boron-doped carbon coating, has been used to improve the electrochemical performances of positive electrodes for lithium-ion batteries, and demonstrates apparent and significant modification effects. In this study, the boron-doped carbon coating is firstly adopted and used to decorate the performance of LiFePO4. The obtained composite exhibits a unique core-shell structure with an average diameter of 140 nm and a 4 nm thick boron-doped carbon shell that uniformly encapsulates the core. Owing to the boron element which could induce high amount of defects in the carbon, the electronic conductivity of LiFePO4 is greatly ameliorated. Thus, the boron-doped composite shows superior rate capability and cycle stability than the undoped sample. For instance, the reversible specific capacity of LiFePO4@B0.4-C can reach 164.1 mAh g-1 at 0.1C, which is approximately 96.5% of the theoretical capacity (170 mAh g-1). Even at high rate of 10C, it still shows a high specific capacity of 126.8 mAh g-1 and can be maintained at 124.5 mAh g-1 after 100 cycles with capacity retention ratio of about 98.2%. This outstanding Li-storage property enable the present design strategy to open up the possibility of fabricating the LiFePO4@B-C composite for high-performance lithium-ion batteries.

3D nitrogen-doped graphene foam with encapsulated germanium/nitrogen-doped graphene yolk-shell nanoarchitecture for high-performance flexible Li-ion battery

PubMed Central

Mo, Runwei; Rooney, David; Sun, Kening; Yang, Hui Ying

2017-01-01

Flexible electrochemical energy storage devices have attracted extensive attention as promising power sources for the ever-growing field of flexible and wearable electronic products. However, the rational design of a novel electrode structure with a good flexibility, high capacity, fast charge–discharge rate and long cycling lifetimes remains a long-standing challenge for developing next-generation flexible energy-storage materials. Herein, we develop a facile and general approach to three-dimensional (3D) interconnected porous nitrogen-doped graphene foam with encapsulated Ge quantum dot/nitrogen-doped graphene yolk-shell nano architecture for high specific reversible capacity (1,220 mAh g−1), long cycling capability (over 96% reversible capacity retention from the second to 1,000 cycles) and ultra-high rate performance (over 800 mAh g−1 at 40 C). This work paves a way to develop the 3D interconnected graphene-based high-capacity electrode material systems, particularly those that suffer from huge volume expansion, for the future development of high-performance flexible energy storage systems. PMID:28051065

Facile synthesis and electrochemical performances of hollow graphene spheres as anode material for lithium-ion batteries

NASA Astrophysics Data System (ADS)

Yao, Ran-Ran; Zhao, Dong-Lin; Bai, Li-Zhong; Yao, Ning-Na; Xu, Li

2014-07-01

The hollow graphene oxide spheres have been successfully fabricated from graphene oxide nanosheets utilizing a water-in-oil emulsion technique, which were prepared from natural flake graphite by oxidation and ultrasonic treatment. The hollow graphene oxide spheres were reduced to hollow graphene spheres at 500°C for 3 h under an atmosphere of Ar(95%)/H2(5%). The first reversible specific capacity of the hollow graphene spheres was as high as 903 mAh g-1 at a current density of 50 mAh g-1. Even at a high current density of 500 mAh g-1, the reversible specific capacity remained at 502 mAh g-1. After 60 cycles, the reversible capacity was still kept at 652 mAh g-1 at the current density of 50 mAh g-1. These results indicate that the prepared hollow graphene spheres possess excellent electrochemical performances for lithium storage. The high rate performance of hollow graphene spheres thanks to the hollow structure, thin and porous shells consisting of graphene sheets.

Facile Synthesis of Coaxial CNTs/MnOx-Carbon Hybrid Nanofibers and Their Greatly Enhanced Lithium Storage Performance.

PubMed

Yang, Zunxian; Lv, Jun; Pang, Haidong; Yan, Wenhuan; Qian, Kun; Guo, Tailiang; Guo, Zaiping

2015-12-01

Carbon nanotubes (CNTs)/MnOx-Carbon hybrid nanofibers have been successfully synthesized by the combination of a liquid chemical redox reaction (LCRR) and a subsequent carbonization heat treatment. The nanostructures exhibit a unique one-dimensional core/shell architecture, with one-dimensional CNTs encapsulated inside and a MnOx-carbon composite nanoparticle layer on the outside. The particular porous characteristics with many meso/micro holes/pores, the highly conductive one-dimensional CNT core, as well as the encapsulating carbon matrix on the outside of the MnOx nanoparticles, lead to excellent electrochemical performance of the electrode. The CNTs/MnOx-Carbon hybrid nanofibers exhibit a high initial reversible capacity of 762.9 mAhg(-1), a high reversible specific capacity of 560.5 mAhg(-1) after 100 cycles, and excellent cycling stability and rate capability, with specific capacity of 396.2 mAhg(-1) when cycled at the current density of 1000 mAg(-1), indicating that the CNTs/MnOx-Carbon hybrid nanofibers are a promising anode candidate for Li-ion batteries.

Facile Synthesis of Coaxial CNTs/MnOx-Carbon Hybrid Nanofibers and Their Greatly Enhanced Lithium Storage Performance

PubMed Central

Yang, Zunxian; Lv, Jun; Pang, Haidong; Yan, Wenhuan; Qian, Kun; Guo, Tailiang; Guo, Zaiping

2015-01-01

Carbon nanotubes (CNTs)/MnOx-Carbon hybrid nanofibers have been successfully synthesized by the combination of a liquid chemical redox reaction (LCRR) and a subsequent carbonization heat treatment. The nanostructures exhibit a unique one-dimensional core/shell architecture, with one-dimensional CNTs encapsulated inside and a MnOx-carbon composite nanoparticle layer on the outside. The particular porous characteristics with many meso/micro holes/pores, the highly conductive one-dimensional CNT core, as well as the encapsulating carbon matrix on the outside of the MnOx nanoparticles, lead to excellent electrochemical performance of the electrode. The CNTs/MnOx-Carbon hybrid nanofibers exhibit a high initial reversible capacity of 762.9 mAhg−1, a high reversible specific capacity of 560.5 mAhg−1 after 100 cycles, and excellent cycling stability and rate capability, with specific capacity of 396.2 mAhg−1 when cycled at the current density of 1000 mAg−1, indicating that the CNTs/MnOx-Carbon hybrid nanofibers are a promising anode candidate for Li-ion batteries. PMID:26621615

Porous nitrogen-doped carbon derived from silk fibroin protein encapsulating sulfur as a superior cathode material for high-performance lithium-sulfur batteries.

PubMed

Zhang, Jiawei; Cai, Yurong; Zhong, Qiwei; Lai, Dongzhi; Yao, Juming

2015-11-14

The features of a carbon substrate are crucial for the electrochemical performance of lithium-sulfur (Li-S) batteries. Nitrogen doping of carbon materials is assumed to play an important role in sulfur immobilisation. In this study, natural silk fibroin protein is used as a precursor of nitrogen-rich carbon to fabricate a novel, porous, nitrogen-doped carbon material through facile carbonisation and activation. Porous carbon, with a reversible capacity of 815 mA h g(-1) at 0.2 C after 60 cycles, serves as the cathode material in Li-S batteries. Porous carbon retains a reversible capacity of 567 mA h g(-1), which corresponds to a capacity retention of 98% at 1 C after 200 cycles. The promising electrochemical performance of porous carbon is attributed to its mesoporous structure, high specific surface area and nitrogen doping into the carbon skeleton. This study provides a general strategy to synthesise nitrogen-doped carbons with a high specific surface area, which is crucial to improve the energy density and electrochemical performance of Li-S batteries.

Freestanding nano crystalline Tin@carbon anode electrodes for high capacity Li-ion batteries

NASA Astrophysics Data System (ADS)

Guler, M. O.; Guzeler, M.; Nalci, D.; Singil, M.; Alkan, E.; Dogan, M.; Guler, A.; Akbulut, H.

2018-07-01

Due to their high specific capacities tin based electrode materials are in the focus of many researchers almost for a decade. However, tin based electrodes are hampered in practical applications due to the volumetric changes during the lithiation and delithiation processes. Therefore, we designed and synthesized a novel "yolk-shell" structure in order to remove these challenges. The production of high purity nano Sn particles were synthesized through a facile chemical reduction method. As-synthesized nano particles were then embedded into conformal and self-standing carbon architectures, designed with hollow space in between the shell and the active electrode particles. As-synthesized Sn@C composite particles were decorated between the layers of graphene produced by Hummers method in order to obtained self-standing thin graphene films. A stable discharge capacity of 284.5 mA h g-1 after 250 cycles is obtained. The results have shown that Sn@C@graphene composite electrodes will be a promising novel candidate electrode material for high capacity lithium ion batteries.

Constructing hierarchical submicrotubes from interconnected TiO2 nanocrystals for high reversible capacity and long-life lithium-ion batteries

NASA Astrophysics Data System (ADS)

Xin, Ling; Liu, Yong; Li, Baojun; Zhou, Xiang; Shen, Hui; Zhao, Wenxia; Liang, Chaolun

2014-03-01

Here, we report a facile hydrothermal approach for synthesizing anatase TiO2 hierarchical mesoporous submicrotubes (ATHMSs) with the aid of long-chain polymer as soft template. The TiO2 nanocrystals, with sizes of 6-8 nm, are well interconnected with each other to build tubular architectures with diameters of 0.3-1.5 μm and lengths of 10-25 μm. Such highly porous structures give rise to very large specific surface area of 201.9 m2 g-1 and 136.8 m2 g-1 for the as-prepared and annealed samples, respectively. By using structurally stable ATHMSs as anode materials for lithium-ion batteries, they exhibited high reversible capacity, long cycling life and excellent cycling stability. Even after 1000 cycles, such ATHMS electrodes retained a reversible discharge capacity as high as 150 mAh g-1 at the current density of 1700 mA g-1, maintaining 92% of the initial discharge capacity (163 mAh g-1).

Building policy-making capacity in the Ministry of Health: the Kazakhstan experience.

PubMed

Chanturidze, Tata; Adams, Orvill; Tokezhanov, Bolat; Naylor, Mike; Richardson, Erica

2015-01-20

Recent economic growth in Kazakhstan has been accompanied by slower improvements in population health and this has renewed impetus for health system reform. Strengthening strategic planning and policy-making capacity in the Ministry of Health has been identified as an important priority, particularly as the Ministry of Health is leading the health system reform process. The intervention was informed by the United Nations Development Programme (UNDP) framework for capacity building which views capacity building as an ongoing process embedded in local institutions and practices. In response to local needs extra elements were included in the framework to tailor the capacity building programme according to the existing policy and budget cycles and respective competence requirements, and link it with transparent career development structures of the Ministry of Health. This aspect of the programme was informed by the institutional capability assessment model used by the United Kingdom National Health Service (NHS) which was adapted to examine the specific organizational and individual competences of the Ministry of Health in Kazakhstan. There were clear successes in building capacity for policy making and strategic planning within the Ministry of Health in Kazakhstan, including better planned, more timely and in-depth responses to policy assignments. Embedding career development as a part of this process was more challenging. This case study highlights the importance of strong political will and high level support for capacity building in ensuring the sustainability of programmes. It also shows that capacity-building programmes need to ensure full engagement with all local stakeholders, or where this is not possible, programmes need to be targeted narrowly to those stakeholders who will benefit most, for the greatest impact to be achieved. In sum, high quality tailor-made capacity development programmes should be based on thorough needs assessment of individual and organizational competences in a specific institutional setting. The experience showed that complementary approaches to human resource development worked effectively in the context of organizations and systems, where an enabling environment was present, and country ownership and political will was complemented by strong technical assistance to design and deliver high quality tailor-made capacity building initiatives.

High levels of time contraction in young children in dual tasks are related to their limited attention capacities.

PubMed

Hallez, Quentin; Droit-Volet, Sylvie

2017-09-01

Numerous studies have shown that durations are judged shorter in a dual-task condition than in a simple-task condition. The resource-based theory of time perception suggests that this is due to the processing of temporal information, which is a demanding cognitive task that consumes limited attention resources. Our study investigated whether this time contraction in a dual-task condition is greater in younger children and, if so, whether this is specifically related to their limited attention capacities. Children aged 5-7years were given a temporal reproduction task in a simple-task condition and a dual-task condition. In addition, different neuropsychological tests were used to assess not only their attention capacities but also their capacities in terms of working memory and information processing speed. The results showed a shortening of perceived time in the dual task compared with the simple task, and this increased as age decreased. The extent of this shortening effect was directly linked to younger children's limited attentional capacities; the lower their attentional capacities, the greater the time contraction. This study demonstrated that children's errors in time judgments are linked to their cognitive capacities rather than to capacities that are specific to time. Copyright © 2017 Elsevier Inc. All rights reserved.

Encapsulation of Fe3O4 Nanoparticles into N, S co-Doped Graphene Sheets with Greatly Enhanced Electrochemical Performance

PubMed Central

Yang, Zunxian; Qian, Kun; Lv, Jun; Yan, Wenhuan; Liu, Jiahui; Ai, Jingwei; Zhang, Yuxiang; Guo, Tailiang; Zhou, Xiongtu; Xu, Sheng; Guo, Zaiping

2016-01-01

Particular N, S co-doped graphene/Fe3O4 hybrids have been successfully synthesized by the combination of a simple hydrothermal process and a subsequent carbonization heat treatment. The nanostructures exhibit a unique composite architecture, with uniformly dispersed Fe3O4 nanoparticles and N, S co-doped graphene encapsulant. The particular porous characteristics with many meso/micro holes/pores, the highly conductive N, S co-doped graphene, as well as the encapsulating N, S co-doped graphene with the high-level nitrogen and sulfur doping, lead to excellent electrochemical performance of the electrode. The N-S-G/Fe3O4 composite electrode exhibits a high initial reversible capacity of 1362.2 mAhg−1, a high reversible specific capacity of 1055.20 mAhg−1 after 100 cycles, and excellent cycling stability and rate capability, with specific capacity of 556.69 mAhg−1 when cycled at the current density of 1000 mAg−1, indicating that the N-S-G/Fe3O4 composite is a promising anode candidate for Li-ion batteries. PMID:27296103

Study on novel functional materials carboxymethyl cellulose lithium (CMC-Li) improve high-performance lithium-ion battery.

PubMed

Qiu, Lei; Shao, Ziqiang; Xiang, Pan; Wang, Daxiong; Zhou, Zhenwen; Wang, Feijun; Wang, Wenjun; Wang, Jianquan

2014-09-22

Novel cellulose derivative CMC-Li was synthesized by cotton as raw material. The mechanism of the CMC-Li modified electrode materials by electrospinning was reported. CMC-Li/lithium iron phosphate (LiFePO4, LFP) composite fiber coated with LFP and CMC-Li nanofibers was successfully obtained by electrospinning. Then, CMC-Li/LFP nano-composite fiber was carbonized under nitrogen at a high temperature formed CNF/LFP/Li (CLL) composite nanofibers as cathode material. It can increase the contents of Li+, and improving the diffusion efficiency and specific capacity. The battery with CLL as cathode material retained close to 100% of initial reversible capacity after 200 cycles at 168 mAh g(-1), which was nearly the theoretical specific capacity of LFP. The cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), X-ray diffraction (XRD) and scanning electron microscope (SEM) were characterizing material performance. The batteries have good electrochemical property, outstanding pollution-free, excellent stability. Copyright © 2014 Elsevier Ltd. All rights reserved.

Flexible phosphorus doped carbon nanosheets/nanofibers: Electrospun preparation and enhanced Li-storage properties as free-standing anodes for lithium ion batteries

NASA Astrophysics Data System (ADS)

Li, Desheng; Wang, Dongya; Rui, Kun; Ma, Zhongyuan; Xie, Ling; Liu, Jinhua; Zhang, Yu; Chen, Runfeng; Yan, Yan; Lin, Huijuan; Xie, Xiaoji; Zhu, Jixin; Huang, Wei

2018-04-01

The emerging wearable and foldable electronic devices drive the development of flexible lithium ion batteries (LIBs). Carbon materials are considered as one of the most promising electrode materials for LIBs due to their light weight, low cost and good structural stability against repeated deformations. However, the specific capacity, rate capability and long-term cycling performance still need to be improved for their applications in next-generation LIBs. Herein, we report a facile approach for immobilizing phosphorus into a large-area carbon nanosheets/nanofibers interwoven free-standing paper for LIBs. As an anode material for LIBs, it shows high reversible capacity of 1100 mAh g-1 at a current density of 200 mA g-1, excellent rate capabilities (e.g., 200 mAh g-1 at 20,000 mA g-1). Even at a high current density of 1000 mA g-1, it still maintains a superior specific capacity of 607 mAh g-1 without obvious decay.

Ultrathin molybdenum diselenide nanosheets anchored on multi-walled carbon nanotubes as anode composites for high performance sodium-ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Zhian; Yang, Xing; Fu, Yun; Du, Ke

2015-11-01

Ultrathin molybdenum diselenide nanosheets are decorated on the surface of multi-walled carbon nanotubes (MWCNT) via a one-step hydrothermal method. Uniform MoSe2 nanosheets are firmly anchored on MWCNT according to the characterizations of scanning electron microscope (SEM), transmission electron microscope (TEM). When evaluated as anodes for sodium storage, the MoSe2@MWCNT composites deliver a reversible specific capacity of 459 mAh g-1 at a current of 200 mA g-1 over 90 cycles, and a specific capacity of 385 mAh g-1 even at a current rate of 2000 mAh g-1, which is better than the MoSe2 nanosheets. The enhanced electrochemical performance of the MoSe2@MWCNT composites can be ascribed to the synergic effects of MoSe2 nanosheets and MWCNT. The high capacity and good rate performance reveal that the MoSe2@MWCNT composites are very promising for applications in sodium-ion batteries.

Carbon-Coated, Diatomite-Derived Nanosilicon as a High Rate Capable Li-ion Battery Anode

PubMed Central

Campbell, Brennan; Ionescu, Robert; Tolchin, Maxwell; Ahmed, Kazi; Favors, Zachary; Bozhilov, Krassimir N.; Ozkan, Cengiz S.; Ozkan, Mihrimah

2016-01-01

Silicon is produced in a variety of ways as an ultra-high capacity lithium-ion battery (LIB) anode material. The traditional carbothermic reduction process required is expensive and energy-intensive; in this work, we use an efficient magnesiothermic reduction to convert the silica-based frustules within diatomaceous earth (diatomite, DE) to nanosilicon (nanoSi) for use as LIB anodes. Polyacrylic acid (PAA) was used as a binder for the DE-based nanoSi anodes for the first time, being attributed for the high silicon utilization under high current densities (up to 4C). The resulting nanoSi exhibited a high BET specific surface area of 162.6 cm2 g−1, compared to a value of 7.3 cm2 g−1 for the original DE. DE contains SiO2 architectures that make ideal bio-derived templates for nanoscaled silicon. The DE-based nanoSi anodes exhibit good cyclability, with a specific discharge capacity of 1102.1 mAh g−1 after 50 cycles at a C-rate of C/5 (0.7 A gSi−1) and high areal loading (2 mg cm−2). This work also demonstrates the fist rate capability testing for a DE-based Si anode; C-rates of C/30 - 4C were tested. At 4C (14.3 A gSi−1), the anode maintained a specific capacity of 654.3 mAh g−1 – nearly 2x higher than graphite’s theoretical value (372 mAh g−1). PMID:27713474

Carbon-Coated, Diatomite-Derived Nanosilicon as a High Rate Capable Li-ion Battery Anode

NASA Astrophysics Data System (ADS)

Campbell, Brennan; Ionescu, Robert; Tolchin, Maxwell; Ahmed, Kazi; Favors, Zachary; Bozhilov, Krassimir N.; Ozkan, Cengiz S.; Ozkan, Mihrimah

2016-10-01

Silicon is produced in a variety of ways as an ultra-high capacity lithium-ion battery (LIB) anode material. The traditional carbothermic reduction process required is expensive and energy-intensive; in this work, we use an efficient magnesiothermic reduction to convert the silica-based frustules within diatomaceous earth (diatomite, DE) to nanosilicon (nanoSi) for use as LIB anodes. Polyacrylic acid (PAA) was used as a binder for the DE-based nanoSi anodes for the first time, being attributed for the high silicon utilization under high current densities (up to 4C). The resulting nanoSi exhibited a high BET specific surface area of 162.6 cm2 g-1, compared to a value of 7.3 cm2 g-1 for the original DE. DE contains SiO2 architectures that make ideal bio-derived templates for nanoscaled silicon. The DE-based nanoSi anodes exhibit good cyclability, with a specific discharge capacity of 1102.1 mAh g-1 after 50 cycles at a C-rate of C/5 (0.7 A gSi-1) and high areal loading (2 mg cm-2). This work also demonstrates the fist rate capability testing for a DE-based Si anode; C-rates of C/30 - 4C were tested. At 4C (14.3 A gSi-1), the anode maintained a specific capacity of 654.3 mAh g-1 - nearly 2x higher than graphite’s theoretical value (372 mAh g-1).

Hydrothermal synthesis and potential applicability of rhombohedral siderite as a high-capacity anode material for lithium ion batteries

NASA Astrophysics Data System (ADS)

Zhao, Shiqiang; Yu, Yue; Wei, Shanshan; Wang, Yuxi; Zhao, Chenhao; Liu, Rui; Shen, Qiang

2014-05-01

Natural siderite is a valuable iron mineral composed of ferrous carbonate (FeCO3), which is commonly found in hydrothermal veins and contains no sulfur or phosphorus. In this paper, micro-sized FeCO3 crystallites are synthesized via a facile hydrothermal route, and almost all of them possess a rhombohedral shape similar to that of natural products. When applied as an anode material for lithium ion batteries, the synthetic siderite can deliver an initial specific discharge capacity of ∼1587 mAh g-1 with a coulombic efficiency of 68% at 200 mA g-1, remaining a reversible value of 1018 mAh g-1 over 120 cycles. Even at a high current density of 1000 mA g-1, after 120 cycles the residual specific capacity (812 mAh g-1) is still higher than the theoretical capacity of FeCO3 (463 mAh g-1). Moreover, a novel reversible conversion mechanism accounts for the excellent electrochemical performances of rhombohedral FeCO3 to a great extent, implying the potential applicability of synthetic siderite as lithium ion battery anodes.

Controlled synthesis of MnOOH multilayer nanowires as anode materials for lithium-ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wu, Yue; Yue, Kaiqiang; Wang, Yuanxin

MnOOH multilayer nanowires have been successfully synthesized by a hydrothermal method. It is found that the uniform multilayer structure of nanowires ran through the entire nanowire, which is formed via a layer by layer. The electrochemical properties of MnOOH multilayer nanowires as an anode material for Li-ion batteries (LIB) were investigated, and excellent capacity retention, superior cycling performance, and high rate capability were achieved. Specifically, the reversible capacity of MnOOH multilayer nanowires is 521 mAh/g after 500 cycles at 0.1 C, with excellent electrochemical stability. The multilayer nanowire electrodes exhibit short electron path lengths, high internal dislocation densities and largemore » surface to volume ratio, resulting in increased specific capacity, cycling stability and rate performance in the energy storage devices, which serves as an indication of their potential application in LIBs. - Highlights: •MnOOH multilayer nanowires were synthesized by a hydrothermal method. •The uniform multilayer structure of nanowires was formed via layer by layer. •The reversible capacity of product shows 521 mAh/g after 500 cycles at 0.1 C. •MnOOH multilayer nanowires showed higher property as anode material in LIB.« less

The acceleration intermediate phase (NiS and Ni3S2) evolution by nanocrystallization in Li/NiS2 thermal batteries with high specific capacity

NASA Astrophysics Data System (ADS)

Jin, Chuanyu; Zhou, Lingping; Fu, Licai; Zhu, Jiajun; Li, Deyi; Yang, Wulin

2017-06-01

The intermediate phase of NiS2 is thought to be a bottleneck currently to improve the overall performance of Li/NiS2 thermal batteries because of its low conductivity and close formation enthalpy between NiS2 and the intermediate phase (NiS, Ni3S2, etc). For improving the discharge performances of Li/NiS2 thermal batteries, the nano NiS2 with an average size of 85 ± 5 nm is designated as a cathode material. The electrochemical measurements show that the specific capacity of nano NiS2 cathode is higher than micro NiS2. The nano NiS2 cathode exhibits excellent electrochemical performances with high specific capacities of 794 and 654 mAh g-1 at current density of 0.1 and 0.5 A cm-2 under a cut-off voltage of 0.5 V, respectively. These results show that the rapid intermediate phase evolution from the nanocrystallization can obviously enhance use efficiency of NiS2 and improve discharge performances of thermal batteries.

Functionalized Fullerenes for Highly Efficient Lithium Ion Storage: Structure-Property-Performance Correlation with Energy Implications

DOE PAGES

Shan, Changsheng; Yen, Hung -Ju; Wu, Kaifeng; ...

2017-08-19

Here, we report that spherical C 60 derivatives with well-defined molecular structures hold great promise to be advanced anode materials for lithium-ion batteries (LIBs). We studied four C 60 molecules with various functional groups, including pristine C 60, carboxyl C 60, ester C 60, and piperazine C 60. The comparison of these C 60s elucidated a strong correlation between functional group, overall packing (crystallinity), and the performance of C 60-based LIBs. Specifically, carboxyl C 60 and neutral ester C 60 showed higher charge capacities than pristine C 60, whereas positively-charged piperazine C 60 exhibited lower capacity. The highest charge capacitymore » was achieved on the carboxyl C 600 (861 mAh g -1 at 100th cycle), which is five times higher than that of pristine C 60 (170 mAh g -1), more than double the theoretical capacity of commercial graphite (372 mAh g -1), and even higher than the theoretical capacity of graphene (744 mAh g -1). Carboxyl C 60 also showed a high capacity at a fast discharge-charge rate (370 mAh g -1 at 5 C). The exceptional performance of carboxyl C 60 can be attributed to multiple key factors. They include the complex formation between lithium ions and oxygen atoms on the carboxyl group, the improved lithium-binding capability of C 60 cage due to electron donating from carboxylate groups, the electrostatic attraction between carboxylate groups and lithium ions, and the large lattice void space and high specific area due to carboxyl functionalization. In conclusion, this study indicates that, while maintaining the basic C 60 electronic properties, functionalization with desired groups can achieve remarkably enhanced capacity and rate performance for lithium storage, thus holding great promise for future LIBs.« less

Functionalized Fullerenes for Highly Efficient Lithium Ion Storage: Structure-Property-Performance Correlation with Energy Implications

DOE Office of Scientific and Technical Information (OSTI.GOV)

Shan, Changsheng; Yen, Hung -Ju; Wu, Kaifeng

Here, we report that spherical C 60 derivatives with well-defined molecular structures hold great promise to be advanced anode materials for lithium-ion batteries (LIBs). We studied four C 60 molecules with various functional groups, including pristine C 60, carboxyl C 60, ester C 60, and piperazine C 60. The comparison of these C 60s elucidated a strong correlation between functional group, overall packing (crystallinity), and the performance of C 60-based LIBs. Specifically, carboxyl C 60 and neutral ester C 60 showed higher charge capacities than pristine C 60, whereas positively-charged piperazine C 60 exhibited lower capacity. The highest charge capacitymore » was achieved on the carboxyl C 600 (861 mAh g -1 at 100th cycle), which is five times higher than that of pristine C 60 (170 mAh g -1), more than double the theoretical capacity of commercial graphite (372 mAh g -1), and even higher than the theoretical capacity of graphene (744 mAh g -1). Carboxyl C 60 also showed a high capacity at a fast discharge-charge rate (370 mAh g -1 at 5 C). The exceptional performance of carboxyl C 60 can be attributed to multiple key factors. They include the complex formation between lithium ions and oxygen atoms on the carboxyl group, the improved lithium-binding capability of C 60 cage due to electron donating from carboxylate groups, the electrostatic attraction between carboxylate groups and lithium ions, and the large lattice void space and high specific area due to carboxyl functionalization. In conclusion, this study indicates that, while maintaining the basic C 60 electronic properties, functionalization with desired groups can achieve remarkably enhanced capacity and rate performance for lithium storage, thus holding great promise for future LIBs.« less

Doped Si nanoparticles with conformal carbon coating and cyclized-polyacrylonitrile network as high-capacity and high-rate lithium-ion battery anodes.

PubMed

Xie, Ming; Piper, Daniela Molina; Tian, Miao; Clancey, Joel; George, Steven M; Lee, Se-Hee; Zhou, Yun

2015-09-11

Doped Si nanoparticles (SiNPs) with conformal carbon coating and cyclized-polyacrylonitrile (PAN) network displayed capacities of 3500 and 3000 mAh g(-1) at C/20 and C/10, respectively. At 1 C, the electrode preserves a specific discharge capacity of ∼1500 mAh g(-1) for at least 60 cycles without decay. Al2O3 atomic layer deposition (ALD) helps improve the initial Coulombic efficiency (CE) to 85%. The dual coating of conformal carbon and cyclized-PAN help alleviate volume change and facilitate charge transfer. Ultra-thin Al2O3 ALD layers help form a stable solid electrolyte interphase interface.

Electrodeposited three-dimensional Ni-Si nanocable arrays as high performance anodes for lithium ion batteries.

PubMed

Liu, Hao; Hu, Liangbin; Meng, Ying Shirley; Li, Quan

2013-11-07

A configuration of three-dimensional Ni-Si nanocable array anodes is proposed to overcome the severe volume change problem of Si during the charging-discharging process. In the fabrication process, a simple and low cost electrodeposition is employed to deposit Si instead of the common expansive vapor phase deposition methods. The optimum composite nanocable array electrode achieves a high specific capacity ~1900 mA h g(-1) at 0.05 C. After 100 cycles at 0.5 C, 88% of the initial capacity (~1300 mA h g(-1)) remains, suggesting its good capacity retention ability. The high performance of the composite nanocable electrode is attributed to its excellent adhesion of the active material on the three-dimensional current collector and short ionic/electronic transport pathways during cycling.

Yolk-Shelled C@Fe3 O4 Nanoboxes as Efficient Sulfur Hosts for High-Performance Lithium-Sulfur Batteries.

PubMed

He, Jiarui; Luo, Liu; Chen, Yuanfu; Manthiram, Arumugam

2017-09-01

Owing to the high theoretical specific capacity (1675 mA h g -1 ) and low cost, lithium-sulfur (Li-S) batteries offer advantages for next-generation energy storage. However, the polysulfide dissolution and low electronic conductivity of sulfur cathodes limit the practical application of Li-S batteries. To address such issues, well-designed yolk-shelled carbon@Fe 3 O 4 (YSC@Fe 3 O 4 ) nanoboxes as highly efficient sulfur hosts for Li-S batteries are reported here. With both physical entrapment by carbon shells and strong chemical interaction with Fe 3 O 4 cores, this unique architecture immobilizes the active material and inhibits diffusion of the polysulfide intermediates. Moreover, due to their high conductivity, the carbon shells and the polar Fe 3 O 4 cores facilitate fast electron/ion transport and promote continuous reactivation of the active material during the charge/discharge process, resulting in improved electrochemical utilization and reversibility. With these merits, the S/YSC@Fe 3 O 4 cathodes support high sulfur content (80 wt%) and loading (5.5 mg cm -2 ) and deliver high specific capacity, excellent rate capacity, and long cycling stability. This work provides a new perspective to design a carbon/metal-oxide-based yolk-shelled framework as a high sulfur-loading host for advanced Li-S batteries with superior electrochemical properties. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High areal capacity hybrid magnesium-lithium-ion battery with 99.9% Coulombic efficiency for large-scale energy storage.

PubMed

Yoo, Hyun Deog; Liang, Yanliang; Li, Yifei; Yao, Yan

2015-04-01

Hybrid magnesium-lithium-ion batteries (MLIBs) featuring dendrite-free deposition of Mg anode and Li-intercalation cathode are safe alternatives to Li-ion batteries for large-scale energy storage. Here we report for the first time the excellent stability of a high areal capacity MLIB cell and dendrite-free deposition behavior of Mg under high current density (2 mA cm(-2)). The hybrid cell showed no capacity loss for 100 cycles with Coulombic efficiency as high as 99.9%, whereas the control cell with a Li-metal anode only retained 30% of its original capacity with Coulombic efficiency well below 90%. The use of TiS2 as a cathode enabled the highest specific capacity and one of the best rate performances among reported MLIBs. Postmortem analysis of the cycled cells revealed dendrite-free Mg deposition on a Mg anode surface, while mossy Li dendrites were observed covering the Li surface and penetrated into separators in the Li cell. The energy density of a MLIB could be further improved by developing electrolytes with higher salt concentration and wider electrochemical window, leading to new opportunities for its application in large-scale energy storage.

Buffer layer enhanced stability of sodium-ion storage

NASA Astrophysics Data System (ADS)

Wang, Xusheng; Yang, Zhanhai; Wang, Chao; Chen, Dong; Li, Rui; Zhang, Xinxiang; Chen, Jitao; Xue, Mianqi

2017-11-01

Se-Se buffer layers are introduced into tin sequences as SnSe2 single crystal to enhance the cycling stability for long-term sodium-ion storage by blazing a trail of self-defence strategy to structural pulverization especially at high current density. Specifically, under half-cell test, the SnSe2 electrodes could yield a high discharge capacity of 345 mAh g-1 after 300 cycles at 1 A g-1 and a high discharge capacity of 300 mAh g-1 after 2100 cycles at 5 A g-1 with stable coulombic efficiency and no capacity fading. Even with the ultrafast sodium-ion storage at 10 A g-1, the cycling stability still makes a positive response and a high discharge capacity of 221 mAh g-1 is demonstrated after 2700 cycles without capacity fading. The full-cell test for the SnSe2 electrodes also demonstrates the superior cycling stability. The flexible and tough Se-Se buffer layers are favourable to accommodate the sodium-ion intercalation process, and the autogenous Na2Se layers could confine the structural pulverization of further sodiated tin sequences by the slip along the Na2Se-NaxSn interfaces.

Aromatic Polyimide/Graphene Composite Organic Cathodes for Fast and Sustainable Lithium-Ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lyu, Hailong; Li, Peipei; Liu, Jiurong

A composite organic cathode material based on aromatic polyimide (PI) and highly conductive graphene was prepared through a facile in situ polymerization method for application in lithium-ion batteries. The in situ polymerization generated intimate contact between PI and electronically conductive graphene, resulting in conductive composites with highly reversible redox reactions and good structure stability. The synergistic effect between PI and graphene enabled not only a high reversible capacity of 232.6 mAh g -1 at a charge–discharge rate of C/10 but also exceptionally high-rate cycling stability, that is, a high capacity of 108.9 mAh g -1 at a very high charge–dischargemore » rate of 50C with a capacity retention of 80 % after 1000 cycles. This improved electrochemical performance resulted from the combination of stable redox reversibility of PI and high electronic conductivity of the graphene additive. In conclusion, the graphene-based composite also exhibited much better performance than composites based on multi-walled carbon nanotubes and the conductive carbon black C45 in terms of specific capacity and long-term cycling stability under the same charge–discharge rates.« less

Aromatic Polyimide/Graphene Composite Organic Cathodes for Fast and Sustainable Lithium-Ion Batteries

DOE PAGES

Lyu, Hailong; Li, Peipei; Liu, Jiurong; ...

2018-01-24

A composite organic cathode material based on aromatic polyimide (PI) and highly conductive graphene was prepared through a facile in situ polymerization method for application in lithium-ion batteries. The in situ polymerization generated intimate contact between PI and electronically conductive graphene, resulting in conductive composites with highly reversible redox reactions and good structure stability. The synergistic effect between PI and graphene enabled not only a high reversible capacity of 232.6 mAh g -1 at a charge–discharge rate of C/10 but also exceptionally high-rate cycling stability, that is, a high capacity of 108.9 mAh g -1 at a very high charge–dischargemore » rate of 50C with a capacity retention of 80 % after 1000 cycles. This improved electrochemical performance resulted from the combination of stable redox reversibility of PI and high electronic conductivity of the graphene additive. In conclusion, the graphene-based composite also exhibited much better performance than composites based on multi-walled carbon nanotubes and the conductive carbon black C45 in terms of specific capacity and long-term cycling stability under the same charge–discharge rates.« less

Mo-doped SnO2 mesoporous hollow structured spheres as anode materials for high-performance lithium ion batteries

NASA Astrophysics Data System (ADS)

Wang, Xuekun; Li, Zhaoqiang; Zhang, Zhiwei; Li, Qun; Guo, Enyan; Wang, Chengxiang; Yin, Longwei

2015-02-01

We designed a facile infiltration route to synthesize mesoporous hollow structured Mo doped SnO2 using silica spheres as templates. It is observed that Mo is uniformly incorporated into SnO2 lattice in the form of Mo6+. The as-prepared mesoporous Mo-doped SnO2 LIBs anodes exhibit a significantly improved electrochemical performance with good cycling stability, high specific capacity and high rate capability. The mesoporous hollow Mo-doped SnO2 sample with 14 at% Mo doping content displays a specific capacity of 801 mA h g-1 after 60 cycles at a current density of 100 mA g-1, about 1.66 times higher than that of the pure SnO2 hollow sample. In addition, even if the current density is as high as 1600 mA g-1 after 60 cycles, it could still retain a stable specific capacity of 530 mA h g-1, exhibiting an extraordinary rate capability. The greatly improved electrochemical performance of the Mo-doped mesoporous hollow SnO2 sample could be attributed to the following factors. The large surface area and hollow structure can significantly enhance structural integrity by acting as mechanical buffer, effectively alleviating the volume changes generated during the lithiation/delithiation process. The incorporation of Mo into the lattice of SnO2 improves charge transfer kinetics and results in a faster Li+ diffusion rate during the charge-discharge process.

A long-life, high-rate lithium/sulfur cell: a multifaceted approach to enhancing cell performance.

PubMed

Song, Min-Kyu; Zhang, Yuegang; Cairns, Elton J

2013-01-01

Lithium/sulfur (Li/S) cells are receiving significant attention as an alternative power source for zero-emission vehicles and advanced electronic devices due to the very high theoretical specific capacity (1675 mA·h/g) of the sulfur cathode. However, the poor cycle life and rate capability have remained a grand challenge, preventing the practical application of this attractive technology. Here, we report that a Li/S cell employing a cetyltrimethyl ammonium bromide (CTAB)-modified sulfur-graphene oxide (S-GO) nanocomposite cathode can be discharged at rates as high as 6C (1C = 1.675 A/g of sulfur) and charged at rates as high as 3C while still maintaining high specific capacity (~ 800 mA·h/g of sulfur at 6C), with a long cycle life exceeding 1500 cycles and an extremely low decay rate (0.039% per cycle), perhaps the best performance demonstrated so far for a Li/S cell. The initial estimated cell-level specific energy of our cell was ~ 500 W·h/kg, which is much higher than that of current Li-ion cells (~ 200 W·h/kg). Even after 1500 cycles, we demonstrate a very high specific capacity (~ 740 mA·h/g of sulfur), which corresponds to ~ 414 mA·h/g of electrode: still higher than state-of-the-art Li-ion cells. Moreover, these Li/S cells with lithium metal electrodes can be cycled with an excellent Coulombic efficiency of 96.3% after 1500 cycles, which was enabled by our new formulation of the ionic liquid-based electrolyte. The performance we demonstrate herein suggests that Li/S cells may already be suitable for high-power applications such as power tools. Li/S cells may now provide a substantial opportunity for the development of zero-emission vehicles with a driving range similar to that of gasoline vehicles.

Specific cooling capacity of liquid nitrogen

NASA Technical Reports Server (NTRS)

Kilgore, R. A.; Adcock, J. B.

1977-01-01

The assumed cooling process and the method used to calculate the specific cooling capacity of liquid nitrogen are described, and the simple equation fitted to the calculated specific cooling capacity data, together with the graphical form calculated values of the specific cooling capacity of nitrogen for stagnation temperatures from saturation to 350 K and stagnation pressures from 1 to 10 atmospheres, are given.

Durable polydopamine-coated porous sulfur core-shell cathode for high performance lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Deng, Yuanfu; Xu, Hui; Bai, Zhaowen; Huang, Baoling; Su, Jingyang; Chen, Guohua

2015-12-01

Lithium-sulfur batteries show fascinating potential for advanced energy system due to their high specific capacity, low-cost, and environmental benignity. However, their wide applications have been plagued by low coulombic efficiency, fast capacity fading and poor rate performance. Herein, a facile method for preparation of S@PDA (PDA = polydopamine) composites with core-shell structure and good electrochemical performance as well as the First-Principles calculations on the interactions of PDA and polysulfides are reported. Taking the advantages of the core-shell structure with porous sulfur core, the high mechanical flexibility of PDA for accommodating the volumetric variation during the discharge/charge processes, the good lithium ion conductivity and the strong chemical interactions between the nitrogen/oxygen atoms with lone electron pair and lithium polysulfides for alleviating their dissolution, the S@PDA composites exhibit high discharge capacities at different current densities (1048 and 869 mAh g-1 at 0.2 and 0.8 A g-1, respectively) and excellent capacity retention capability. A capacity decay as low as 0.021% per cycle and an average coulombic efficiency of 98.5% is observed over a long-term cycling of 890 cycles at 0.8 A g-1. The S@PDA electrode has great potential as a low-cost cathode in high energy Li-S batteries.

Comparison of basic physical fitness, aerobic capacity, and isokinetic strength between national and international level high school freestyle swimmers

PubMed Central

Bae, Young-Hyeon; Yu, Jae-Ho; Lee, Suk Min

2016-01-01

[Purpose] This study aimed to compare basic physical fitness, aerobic capacity, and isokinetic strength between international and national level freestyle high school student swimmers. [Subjects and Methods] A total of 28 participants (14 international level swimmers and 14 national level freestyle high school student swimmers) with no known pathology were included. We used a cross-sectional study to examine three variables: basic physical fitness, aerobic capacity, and isokinetic strength. [Results] The mean values of these variables in the international level swimmers were higher than those in the national level swimmers. Swimmers are generally physically fit with a good competition record. [Conclusion] An appropriate training program, which considers specific individual characteristics is likely to have a positive impact on the improvement of total physical fitness, and subsequently, on the performance of the freestyle high school swimmer. PMID:27134379

Ontogeny of intestinal safety factors: lactase capacities and lactose loads.

PubMed

O'Connor, T P; Diamond, J

1999-03-01

We measured intestinal safety factors (ratio of a physiological capacity to the load on it) for lactose digestion in developing rat pups. Specifically, we assessed the quantitative relationships between lactose load and the series capacities of lactase and the Na+-glucose cotransporter (SGLT-1). Both capacities increased significantly with age in suckling pups as a result of increasing intestinal mass and maintenance of mass-specific activities. The youngest pups examined (5 days) had surprisingly high safety factors of 8-13 for both lactase and SGLT-1, possibly because milk contains lactase substrates other than lactose; it also, however, suggests that their intestinal capacities were being prepared to meet future demands rather than just current ones. By day 10 (and also at day 15), increased lactose loads resulted in lower safety factors of 4-6, values more typical of adult intestines. The safety factor of SGLT-1 in day 30 (weanling) and day 100 (adult) rats was only approximately 1.0. This was initially unexpected, because most adult intestines maintain a modest reserve capacity beyond nutrient load values, but postweaning rats appear to use hindgut fermentation, assessed by gut morphology and hydrogen production assays, as a built-in reserve capacity. The series capacities of lactase and SGLT-1 varied in concert with each other over ontogeny and as lactose load was manipulated by experimental variation in litter size.

Assessing research activity and capacity of community-based organizations: development and pilot testing of an instrument.

PubMed

Humphries, Debbie L; Carroll-Scott, Amy; Mitchell, Leif; Tian, Terry; Choudhury, Shonali; Fiellin, David A

2014-01-01

Although awareness of the importance of the research capacity of community-based organizations (CBOs) is growing, a uniform framework of the research capacity domains within CBOs has not yet been developed. To develop a framework and instrument (the Community REsearch Activity assessment Tool [CREAT]) for assessing the research activity and capacity of CBOs that incorporates awareness of the different data collection and analysis priorities of CBOs. We conducted a review of existing tools for assessing research capacity to identify key capacity domains. Instrument items were developed through an iterative process with CBO representatives and community researchers. The CREAT was then pilot tested with 30 CBOs. The four primary domains of the CREAT framework include 1) organizational support for research, 2) generalizable experiences, 3) research specific experiences, and 4) funding. Organizations reported a high prevalence of activities in the research-specific experiences domain, including conducting literature reviews (70%), use of research terminology (83%), and primary data collection (100%). Respondents see research findings as important to improve program and service delivery, and to seek funds for new programs and services. Funders, board members, and policymakers are the most important dissemination audiences. The work reported herein advances the field of CBO research capacity by developing a systematic framework for assessing research activity and capacity relevant to the work of CBOs, and by developing and piloting an instrument to assess activity in these domains.

16 CFR Appendix J1 to Part 305 - Pool Heaters-Gas

Code of Federal Regulations, 2014 CFR

2014-01-01

... Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS ENERGY AND WATER USE LABELING FOR CONSUMER PRODUCTS UNDER THE ENERGY POLICY AND CONSERVATION ACT (âENERGY LABELING... heating capacity Range of thermal efficiencies(percent) Natural gas Low High Propane Low High Low High All...

Electrochemically fabricated polypyrrole-cobalt-oxygen coordination complex as high-performance lithium-storage materials.

PubMed

Guo, Bingkun; Kong, Qingyu; Zhu, Ying; Mao, Ya; Wang, Zhaoxiang; Wan, Meixiang; Chen, Liquan

2011-12-23

Current lithium-ion battery (LIB) technologies are all based on inorganic electrode materials, though organic materials have been used as electrodes for years. Disadvantages such as limited thermal stability and low specific capacity hinder their applications. On the other hand, the transition metal oxides that provide high lithium-storage capacity by way of electrochemical conversion reaction suffer from poor cycling stability. Here we report a novel high-performance, organic, lithium-storage material, a polypyrrole-cobalt-oxygen (PPy-Co-O) coordination complex, with high lithium-storage capacity and excellent cycling stability. Extended X-ray absorption fine structure and Raman spectroscopy and other physical and electrochemical characterizations demonstrate that this coordination complex can be electrochemically fabricated by cycling PPy-coated Co(3)O(4) between 0.0 V and 3.0 V versus Li(+)/Li. Density functional theory (DFT) calculations indicate that each cobalt atom coordinates with two nitrogen atoms within the PPy-Co coordination layer and the layers are connected with oxygen atoms between them. Coordination weakens the C-H bonds on PPy and makes the complex a novel lithium-storage material with high capacity and high cycling stability. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Site of maxima of conductivity, temperatures, density of the current and specific capacity of the thermal emission in the HFI-discharge

NASA Astrophysics Data System (ADS)

Gerasimov, A.; Kirpichnikov, A.; Sabirova, F.; Gainullin, R.

2017-11-01

On the basis of theoretical analysis of distributions of the conductivity, current density and specific power of heat release in the high-frequency induction discharge, a law of crowding of maxima of these values has been established.

Comparison of cytomegalovirus (CMV)-specific neutralization capacity of hyperimmunoglobulin (HIG) versus standard intravenous immunoglobulin (IVIG) preparations: Impact of CMV IgG normalization.

PubMed

Schampera, Matthias Stefan; Schweinzer, Katrin; Abele, Harald; Kagan, Karl Oliver; Klein, Reinhild; Rettig, Ingo; Jahn, Gerhard; Hamprecht, Klaus

2017-05-01

Based on a non-randomized study of Nigro et al. (2005) the intravenous administration of hyperimmunoglobulins (HIGs) is applied frequently to women with primary CMV-infection as "off-label use" in Germany. In order to describe their CMV-specific neutralization-capacity in vitro, we analyzed the HIG preparations Cytotect ® , and Cytogam ® as well as the standard intravenous immunoglobulins (IVIG) Octagam ® , Gamunex ® , Kiovig ® . We performed short-term cell-free CMV neutralization assays (CFNT) and long-term cell-adapted neutralization-plaque-reduction assays (PRANT). Human retinal epithelial cells (ARPE-19) were used as target cells. A clinical CMV primary-isolate from amnion fluid propagated in epithelial cells without any initial fibroblast adaption was used. For calibration we previously generated serum-pools (N=100) from two cohorts of mothers at birth: seronegative and latently CMV-infected mothers. Biochemical analysis included total protein, albumin, Ig-class, and IgG-subclasses. Additionally, CMV antibody-reactivity was checked using recombinant immunoblotting. HIG and IVIG preparations showed differences in levels and patterns of protein, Ig-class and CMV-specific antibody concentrations. All IgG-preparations showed high in vitro NT-capacity and high IgG-avidity. The NT 90 -values for HIGs and IVIGs and our seropositive reference-pool showed similar NT-capacity at a dilution of (1:100) which corresponded well to 4.1 PEI-Units/ml. All HIG- and IVIG-preparations showed similar NT-capacity following CMV IgG-normalization. Our in vitro results are in strong contrast to former findings suggesting higher functional CMV NT titers in IVIG-preparations compared to HIGs. Copyright © 2017 Elsevier B.V. All rights reserved.

Charge Modulation in Graphitic Carbon Nitride as a Switchable Approach to High-Capacity Hydrogen Storage.

PubMed

Tan, Xin; Kou, Liangzhi; Tahini, Hassan A; Smith, Sean C

2015-11-01

Electrical charging of graphitic carbon nitride nanosheets (g-C4 N3 and g-C3 N4 ) is proposed as a strategy for high-capacity and electrocatalytically switchable hydrogen storage. Using first-principle calculations, we found that the adsorption energy of H2 molecules on graphitic carbon nitride nanosheets is dramatically enhanced by injecting extra electrons into the adsorbent. At full hydrogen coverage, the negatively charged graphitic carbon nitride achieves storage capacities up to 6-7 wt %. In contrast to other hydrogen storage approaches, the storage/release occurs spontaneously once extra electrons are introduced or removed, and these processes can be simply controlled by switching on/off the charging voltage. Therefore, this approach promises both facile reversibility and tunable kinetics without the need of specific catalysts. Importantly, g-C4 N3 has good electrical conductivity and high electron mobility, which can be a very good candidate for electron injection/release. These predictions may prove to be instrumental in searching for a new class of high-capacity hydrogen storage materials. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

High Per formance and Flexible Supercapacitors based on Carbonized Bamboo Fibers for Wide Temperature Applications

PubMed Central

Zequine, Camila; Ranaweera, C. K.; Wang, Z.; Singh, Sweta; Tripathi, Prashant; Srivastava, O. N.; Gupta, Bipin Kumar; Ramasamy, K.; Kahol, P. K.; Dvornic, P. R.; Gupta, Ram K.

2016-01-01

High performance carbonized bamboo fibers were synthesized for a wide range of temperature dependent energy storage applications. The structural and electrochemical properties of the carbonized bamboo fibers were studied for flexible supercapacitor applications. The galvanostatic charge-discharge studies on carbonized fibers exhibited specific capacity of ~510F/g at 0.4 A/g with energy density of 54 Wh/kg. Interestingly, the carbonized bamboo fibers displayed excellent charge storage stability without any appreciable degradation in charge storage capacity over 5,000 charge-discharge cycles. The symmetrical supercapacitor device fabricated using these carbonized bamboo fibers exhibited an areal capacitance of ~1.55 F/cm2 at room temperature. In addition to high charge storage capacity and cyclic stability, the device showed excellent flexibility without any degradation to charge storage capacity on bending the electrode. The performance of the supercapacitor device exhibited ~65% improvement at 70 °C compare to that at 10 °C. Our studies suggest that carbonized bamboo fibers are promising candidates for stable, high performance and flexible supercapacitor devices. PMID:27546225

High Per formance and Flexible Supercapacitors based on Carbonized Bamboo Fibers for Wide Temperature Applications.

PubMed

Zequine, Camila; Ranaweera, C K; Wang, Z; Singh, Sweta; Tripathi, Prashant; Srivastava, O N; Gupta, Bipin Kumar; Ramasamy, K; Kahol, P K; Dvornic, P R; Gupta, Ram K

2016-08-22

High performance carbonized bamboo fibers were synthesized for a wide range of temperature dependent energy storage applications. The structural and electrochemical properties of the carbonized bamboo fibers were studied for flexible supercapacitor applications. The galvanostatic charge-discharge studies on carbonized fibers exhibited specific capacity of ~510F/g at 0.4 A/g with energy density of 54 Wh/kg. Interestingly, the carbonized bamboo fibers displayed excellent charge storage stability without any appreciable degradation in charge storage capacity over 5,000 charge-discharge cycles. The symmetrical supercapacitor device fabricated using these carbonized bamboo fibers exhibited an areal capacitance of ~1.55 F/cm(2) at room temperature. In addition to high charge storage capacity and cyclic stability, the device showed excellent flexibility without any degradation to charge storage capacity on bending the electrode. The performance of the supercapacitor device exhibited ~65% improvement at 70 °C compare to that at 10 °C. Our studies suggest that carbonized bamboo fibers are promising candidates for stable, high performance and flexible supercapacitor devices.

High Per formance and Flexible Supercapacitors based on Carbonized Bamboo Fibers for Wide Temperature Applications

NASA Astrophysics Data System (ADS)

Zequine, Camila; Ranaweera, C. K.; Wang, Z.; Singh, Sweta; Tripathi, Prashant; Srivastava, O. N.; Gupta, Bipin Kumar; Ramasamy, K.; Kahol, P. K.; Dvornic, P. R.; Gupta, Ram K.

2016-08-01

High performance carbonized bamboo fibers were synthesized for a wide range of temperature dependent energy storage applications. The structural and electrochemical properties of the carbonized bamboo fibers were studied for flexible supercapacitor applications. The galvanostatic charge-discharge studies on carbonized fibers exhibited specific capacity of ~510F/g at 0.4 A/g with energy density of 54 Wh/kg. Interestingly, the carbonized bamboo fibers displayed excellent charge storage stability without any appreciable degradation in charge storage capacity over 5,000 charge-discharge cycles. The symmetrical supercapacitor device fabricated using these carbonized bamboo fibers exhibited an areal capacitance of ~1.55 F/cm2 at room temperature. In addition to high charge storage capacity and cyclic stability, the device showed excellent flexibility without any degradation to charge storage capacity on bending the electrode. The performance of the supercapacitor device exhibited ~65% improvement at 70 °C compare to that at 10 °C. Our studies suggest that carbonized bamboo fibers are promising candidates for stable, high performance and flexible supercapacitor devices.

Layered sulfur/PEDOT:PSS nano composite electrodes for lithium sulfur cell applications

NASA Astrophysics Data System (ADS)

Anilkumar, K. M.; Jinisha, B.; Manoj, M.; Pradeep, V. S.; Jayalekshmi, S.

2018-06-01

Lithium-Sulfur (Li-S) cells are emerging as the next generation energy storage devices owing to their impressive electrochemical properties with high theoretical specific capacity of 1675 mAh/g. Lack of electronic conductivity of sulfur, its volume expansion during high lithium intake and the shuttling effect due to the formation of soluble polysulfides are the main limitations, delaying the commercialization of this technology. To address these challenges, in the present work, the conducting polymer PEDOT:PSS is used as the covering matrix over the sulfur particles to improve their Li storage properties. The sulfur/PEDOT:PSS nanocomposite is synthesised using the hydrothermal process and its formation with the polymer coating over sulfur nanoparticles is established from the XRD, Raman spectroscopy, FE-SEM and TEM studies. The electrochemical studies show that the cells assembled using the sulfur/PEDOT:PSS nanocomposite as the cathode, with the components taken in the weight ratio of 9:1, offer a reversible capacity of 1191 mAh g-1 at 0.1C rate. These cells display stable electrochemical capacities over 200 cycles at gradually increasing current rates. The polymer layer facilitates electronic conduction and suppresses the polysulfide formation and the volume expansion of sulfur. A reversible capacity of 664 mAh g-1 is observed after 200 cycles at 1C rate with the capacity retention of 75 % of the initial stable capacity. The highlight of the present work is the possibility to achieve high discharge capacities at high C rates and the retention of a good percentage of the initial capacity over 200 cycles, for these Li-S cells.

Tailored Organic Electrode Material Compatible with Sulfide Electrolyte for Stable All-Solid-State Sodium Batteries.

PubMed

Chi, Xiaowei; Liang, Yanliang; Hao, Fang; Zhang, Ye; Whiteley, Justin; Dong, Hui; Hu, Pu; Lee, Sehee; Yao, Yan

2018-03-01

All-solid-state sodium batteries (ASSSBs) with nonflammable electrolytes and ubiquitous sodium resource are a promising solution to the safety and cost concerns for lithium-ion batteries. However, the intrinsic mismatch between low anodic decomposition potential of superionic sulfide electrolytes and high operating potentials of sodium-ion cathodes leads to a volatile cathode-electrolyte interface and undesirable cell performance. Here we report a high-capacity organic cathode, Na 4 C 6 O 6 , that is chemically and electrochemically compatible with sulfide electrolytes. A bulk-type ASSSB shows high specific capacity (184 mAh g -1 ) and one of the highest specific energies (395 Wh kg -1 ) among intercalation compound-based ASSSBs. The capacity retentions of 76 % after 100 cycles at 0.1 C and 70 % after 400 cycles at 0.2 C represent the record stability for ASSSBs. Additionally, Na 4 C 6 O 6 functions as a capable anode material, enabling a symmetric all-organic ASSSB with Na 4 C 6 O 6 as both cathode and anode materials. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Porous lithium nickel cobalt manganese oxide hierarchical nanosheets as high rate capability cathodes for lithium ion batteries

NASA Astrophysics Data System (ADS)

Li, Jili; Wang, Xiaofeng; Zhao, Junwei; Chen, Jian; Jia, Tiekun; Cao, Chuanbao

2016-03-01

Novel 2D LiNi1/3Co1/3Mn1/3O2 hierarchical nanosheets are successfully synthesized through a simple sol-gel strategy with ethanol dispersion of carbon nanotubes as addictive. The nanosheets with thickness of ∼100 nm appear porous and are formed by 100 nm nanoparticles. As cathode for lithium ion battery, the 2D porous hierarchical nanosheets demonstrate high specific capacity of 137.7 mAh g-1 at 20C (1C = 200 mA g-1), which is much higher than those of its counterparts. The high capacity can be still maintained during 100 charge/discharge cycles and the capacity retention is up to 90.1%. The excellent rate capability and cyclability may be attributed to the distinct 2D porous hierarchical structure.

Dual-carbon enhanced silicon-based composite as superior anode material for lithium ion batteries

NASA Astrophysics Data System (ADS)

Wang, Jie; Liu, Dai-Huo; Wang, Ying-Ying; Hou, Bao-Hua; Zhang, Jing-Ping; Wang, Rong-Shun; Wu, Xing-Long

2016-03-01

Dual-carbon enhanced Si-based composite (Si/C/G) has been prepared via employing the widely distributed, low-cost and environmentally friendly Diatomite mineral as silicon raw material. The preparation processes are very simple, non-toxic and easy to scale up. Electrochemical tests as anode material for lithium ion batteries (LIBs) demonstrate that this Si/C/G composite exhibits much improved Li-storage properties in terms of superior high-rate capabilities and excellent cycle stability compared to the pristine Si material as well as both single-carbon modified composites. Specifically for the Si/C/G composite, it can still deliver a high specific capacity of about 470 mAh g-1 at an ultrahigh current density of 5 A g-1, and exhibit a high capacity of 938 mAh g-1 at 0.1 A g-1 with excellent capacity retention in the following 300 cycles. The significantly enhanced Li-storage properties should be attributed to the co-existence of both highly conductive graphite and amorphous carbon in the Si/C/G composite. While the former can enhance the electrical conductivity of the obtained composite, the latter acts as the adhesives to connect the porous Si particulates and conductive graphite flakes to form robust and stable conductive network.

O3-type Na(Mn₀.₂₅Fe₀.₂₅Co₀.₂₅Ni₀.₂₅)O₂: a quaternary layered cathode compound for rechargeable Na ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Li, Xi; Zhou, Yong-Ning; Wu, Di

2014-12-01

We report a new layered Na(Mn₀.₂₅Fe₀.₂₅Co₀.₂₅Ni₀.₂₅)O₂ compound with O3 oxygen stacking. It delivers 180 mAh/g initial discharge capacity and 578 Wh/kg specific energy density with good cycling capability at high cutoff voltage. In situ X-ray diffraction (XRD) shows a reversible structure evolution of O3-P3-O3'-O3'' upon Na de-intercalation. The excellent capacity and cycling performance at high cutoff voltage make it an important model system for studying the general issue of capacity fading in layered Na cathode compounds.

High-Temperature Adiabatic Calorimeter for Constant-Volume Heat Capacity Measurements of Compressed Gases and Liquids

PubMed Central

Magee, Joseph W.; Deal, Renee J.; Blanco, John C.

1998-01-01

A high-temperature adiabatic calorimeter has been developed to measure the constant-volume specific heat capacities (cV) of both gases and liquids, especially fluids of interest to emerging energy technologies. The chief design feature is its nearly identical twin bomb arrangement, which allows accurate measurement of energy differences without large corrections for energy losses due to thermal radiation fluxes. Operating conditions for the calorimeter cover a range of temperatures from 250 K to 700 K and at pressures up to 20 MPa. Performance tests were made with a sample of twice-distilled water. Heat capacities for water were measured from 300 K to 420 K at pressures to 20 MPa. The measured heat capacities differed from those calculated with an independently developed standard reference formulation with a root-mean-square fractional deviation of 0.48 %. PMID:28009375

Does selection for gamete dispersal and capture lead to a sex difference in clump water-holding capacity?

PubMed

Moore, Jonathan D; Kollar, Leslie M; McLetchie, D Nicholas

2016-08-01

Differences in male and female reproductive function can lead to selection for sex-specific gamete dispersal and capture traits. These traits have been explored from shoot to whole plant levels in wind-pollinated species. While shoot traits have been explored in water-fertilized species, little is known about how whole plant morphology affects gamete dispersal and capture. We used the dioecious, water-fertilized plant Bryum argenteum to test for differences in clump morphology and water-holding characteristics consistent with divergent selection. We hypothesized that sex-specific clump morphology, arising at maturity, produces relatively low male water-holding capacity for gamete dispersal and high female capacity for gamete capture. We measured isolated young shoot and clump water-holding capacity and clump morphological characteristics on greenhouse-grown plants. Young shoot capacity was used to predict clump capacity, which was compared with actual clump capacity. Young male shoots held more water per unit length, and male clumps had higher shoot density, which extrapolated to higher clump water-holding capacity. However, female clumps held more water and were taller with more robust shoots. Actual clump capacity correlated positively with clump height and shoot cross-sectional area. The sex difference in actual clump capacity and its unpredictability from younger shoots are consistent with our hypothesis that males should hold less water than females to facilitate sexual reproduction. These results provide conceptual connections to other plant groups and implications for connecting divergent selection to female-biased sex ratios in B. argenteum and other bryophytes. © 2016 Botanical Society of America.

High-energy lithium-ion hybrid supercapacitors composed of hierarchical urchin-like WO3/C anodes and MOF-derived polyhedral hollow carbon cathodes.

PubMed

Xu, Juan; Li, Yuanyuan; Wang, Lei; Cai, Qifa; Li, Qingwei; Gao, Biao; Zhang, Xuming; Huo, Kaifu; Chu, Paul K

2016-09-22

A lithium-ion hybrid supercapacitor (Li-HSC) comprising a Li-ion battery type anode and an electrochemical double layer capacitance (EDLC) type cathode has attracted much interest because it accomplishes a large energy density without compromising the power density. In this work, hierarchical carbon coated WO 3 (WO 3 /C) with a unique mesoporous structure and metal-organic framework derived nitrogen-doped carbon hollow polyhedra (MOF-NC) are prepared and adopted as the anode and the cathode for Li-HSCs. The hierarchical mesoporous WO 3 /C microspheres assembled by radially oriented WO 3 /C nanorods along the (001) plane enable effective Li + insertion, thus exhibit high capacity, excellent rate performance and a long cycling life due to their high Li + conductivity, electronic conductivity and structural robustness. The WO 3 /C structure shows a reversible specific capacity of 508 mA h g -1 at a 0.1 C rate (1 C = 696 mA h g -1 ) after 160 discharging-charging cycles with excellent rate capability. The MOF-NC achieved the specific capacity of 269.9 F g -1 at a current density of 0.2 A g -1 . At a high current density of 6 A g -1 , 92.4% of the initial capacity could be retained after 2000 discharging-charging cycles, suggesting excellent cycle stability. The Li-HSC comprising a WO 3 /C anode and a MOF-NC cathode boasts a large energy density of 159.97 W h kg -1 at a power density of 173.6 W kg -1 and 88.3% of the capacity is retained at a current density of 5 A g -1 after 3000 charging-discharging cycles, which are better than those previously reported for Li-HSCs. The high energy and power densities of the Li-HSCs of WO 3 /C//MOF-NC render large potential in energy storage.

Abiotic and biotic determinants of leaf carbon exchange capacity from tropical to high boreal biomes

NASA Astrophysics Data System (ADS)

Smith, N. G.; Dukes, J. S.

2016-12-01

Photosynthesis and respiration on land represent the two largest fluxes of carbon dioxide between the atmosphere and the Earth's surface. As such, the Earth System Models that are used to project climate change are high sensitive to these processes. Studies have found that much of this uncertainty is due to the formulation and parameterization of plant photosynthetic and respiratory capacity. Here, we quantified the abiotic and biotic factors that determine photosynthetic and respiratory capacity at large spatial scales. Specifically, we measured the maximum rate of Rubisco carboxylation (Vcmax), the maximum rate of Ribulose-1,5-bisphosphate regeneration (Jmax), and leaf dark respiration (Rd) in >600 individuals of 98 plant species from the tropical to high boreal biomes of Northern and Central America. We also measured a bevy of covariates including plant functional type, leaf nitrogen content, short- and long-term climate, leaf water potential, plant size, and leaf mass per area. We found that plant functional type and leaf nitrogen content were the primary determinants of Vcmax, Jmax, and Rd. Mean annual temperature and mean annual precipitation were not significant predictors of these rates. However, short-term climatic variables, specifically soil moisture and air temperature over the previous 25 days, were significant predictors and indicated that heat and soil moisture deficits combine to reduce photosynthetic capacity and increase respiratory capacity. Finally, these data were used as a model benchmarking tool for the Community Land Model version 4.5 (CLM 4.5). The benchmarking analyses determined errors in the leaf nitrogen allocation scheme of CLM 4.5. Under high leaf nitrogen levels within a plant type the model overestimated Vcmax and Jmax. This result suggested that plants were altering their nitrogen allocation patterns when leaf nitrogen levels were high, an effect that was not being captured by the model. These data, taken with models in mind, provide paths forward for improving model structure and parameterization of leaf carbon exchange at large spatial scales.

Vertically-aligned carbon nanotubes on aluminum as a light-weight positive electrode for lithium-polysulfide batteries.

PubMed

Liatard, S; Benhamouda, K; Fournier, A; Ramos, R; Barchasz, C; Dijon, J

2015-05-04

A light-weight, high specific surface current collector made of vertically-aligned carbon nanotubes grown on an aluminum substrate was fabricated and studied as a positive electrode in a semi-liquid lithium/polysulfide battery. This simple system delivered stable capacities over 1000 mA h gS(-1) and 2 mA h cm(-2) with almost no capacity loss over 50 cycles.

Semi-solid electrodes having high rate capability

DOEpatents

Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

2016-07-05

Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

Semi-solid electrodes having high rate capability

DOEpatents

Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

2015-11-10

Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

Mesoporous nickel oxide nanowires: hydrothermal synthesis, characterisation and applications for lithium-ion batteries and supercapacitors with superior performance.

PubMed

Su, Dawei; Kim, Hyun-Soo; Kim, Woo-Seong; Wang, Guoxiu

2012-06-25

Mesoporous nickel oxide nanowires were synthesized by a hydrothermal reaction and subsequent annealing at 400 °C. The porous one-dimensional nanostructures were analysed by field-emission SEM, high-resolution TEM and N(2) adsorption/desorption isotherm measurements. When applied as the anode material in lithium-ion batteries, the as-prepared mesoporous nickel oxide nanowires demonstrated outstanding electrochemical performance with high lithium storage capacity, satisfactory cyclability and an excellent rate capacity. They also exhibited a high specific capacitance of 348 F g(-1) as electrodes in supercapacitors. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Graphene-wrapped sulfur particles as a rechargeable lithium-sulfur battery cathode material with high capacity and cycling stability.

PubMed

Wang, Hailiang; Yang, Yuan; Liang, Yongye; Robinson, Joshua Tucker; Li, Yanguang; Jackson, Ariel; Cui, Yi; Dai, Hongjie

2011-07-13

We report the synthesis of a graphene-sulfur composite material by wrapping poly(ethylene glycol) (PEG) coated submicrometer sulfur particles with mildly oxidized graphene oxide sheets decorated by carbon black nanoparticles. The PEG and graphene coating layers are important to accommodating volume expansion of the coated sulfur particles during discharge, trapping soluble polysulfide intermediates, and rendering the sulfur particles electrically conducting. The resulting graphene-sulfur composite showed high and stable specific capacities up to ∼600 mAh/g over more than 100 cycles, representing a promising cathode material for rechargeable lithium batteries with high energy density.

The sensory components of high-capacity iconic memory and visual working memory.

PubMed

Bradley, Claire; Pearson, Joel

2012-01-01

EARLY VISUAL MEMORY CAN BE SPLIT INTO TWO PRIMARY COMPONENTS: a high-capacity, short-lived iconic memory followed by a limited-capacity visual working memory that can last many seconds. Whereas a large number of studies have investigated visual working memory for low-level sensory features, much research on iconic memory has used more "high-level" alphanumeric stimuli such as letters or numbers. These two forms of memory are typically examined separately, despite an intrinsic overlap in their characteristics. Here, we used a purely sensory paradigm to examine visual short-term memory for 10 homogeneous items of three different visual features (color, orientation and motion) across a range of durations from 0 to 6 s. We found that the amount of information stored in iconic memory is smaller for motion than for color or orientation. Performance declined exponentially with longer storage durations and reached chance levels after ∼2 s. Further experiments showed that performance for the 10 items at 1 s was contingent on unperturbed attentional resources. In addition, for orientation stimuli, performance was contingent on the location of stimuli in the visual field, especially for short cue delays. Overall, our results suggest a smooth transition between an automatic, high-capacity, feature-specific sensory-iconic memory, and an effortful "lower-capacity" visual working memory.

Tailoring the surface properties of LiNi 0.4Mn 0.4Co 0.2O₂ by titanium substitution for improved high voltage cycling performance

DOE PAGES

Wolff-Goodrich, Silas; Xin, Huolin L.; Lin, Feng; ...

2015-07-30

The present research aims to provide insights into the behavior of LiNi0.4Mn0.4Co0.2O2 (NMC442) and LiNi 0.4Mn 0.4Co 0.2O₂ (NMC442-Ti02) cathode materials under galvanostatic cycling to high potentials, in the context of previous work which predicted that Ti-substituted variants should deliver higher capacities and exhibit better cycling stability than the unsubstituted compounds. It is found that NMC cathodes containing Ti show equivalent capacity fading but greater specific capacity than those without Ti in the same potential range. When repeatedly charged to the same degree of delithiation, NMC cathodes containing Ti showed better capacity retention. Soft x-ray absorption spectroscopy (XAS) spectra formore » Mn and Co indicated increased reduction in these elements for NMC cathodes without Ti, indicating that the substitution of Ti for Co acts to suppress the formation of a high impedance rock salt phase at the surface of NMC cathode particles. The results of this study validate the adoption of a facile change to existing NMC chemistries to improve cathode capacity retention under high voltage cycling conditions.« less

In Situ Activation of Nitrogen-Doped Graphene Anchored on Graphite Foam for a High-Capacity Anode.

PubMed

Ji, Junyi; Liu, Jilei; Lai, Linfei; Zhao, Xin; Zhen, Yongda; Lin, Jianyi; Zhu, Yanwu; Ji, Hengxing; Zhang, Li Li; Ruoff, Rodney S

2015-08-25

We report the fabrication of a three-dimensional free-standing nitrogen-doped porous graphene/graphite foam by in situ activation of nitrogen-doped graphene on highly conductive graphite foam (GF). After in situ activation, intimate "sheet contact" was observed between the graphene sheets and the GF. The sheet contact produced by in situ activation is found to be superior to the "point contact" obtained by the traditional drop-casting method and facilitates electron transfer. Due to the intimate contact as well as the use of an ultralight GF current collector, the composite electrode delivers a gravimetric capacity of 642 mAh g(-1) and a volumetric capacity of 602 mAh cm(-3) with respect to the whole electrode mass and volume (including the active materials and the GF current collector). When normalized based on the mass of the active material, the composite electrode delivers a high specific capacity of up to 1687 mAh g(-1), which is superior to that of most graphene-based electrodes. Also, after ∼90 s charging, the anode delivers a capacity of about 100 mAh g(-1) (with respect to the total mass of the electrode), indicating its potential use in high-rate lithium-ion batteries.

Nitrogen expander cycles for large capacity liquefaction of natural gas

NASA Astrophysics Data System (ADS)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun; Choe, Kun Hyung

2014-01-01

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

Highly conductive porous Na-embedded carbon nanowalls for high-performance capacitive deionization

NASA Astrophysics Data System (ADS)

Chang, Liang; Hu, Yun Hang

2018-05-01

Highly conductive porous Na-embedded carbon nanowalls (Na@C), which were recently invented, have exhibited excellent performance for dye-sensitized solar cells and electric double-layer capacitors. In this work, Na@C was demonstrated as an excellent electrode material for capacitive deionization (CDI). In a three-electrode configuration system, the specific capacity of the Na@C electrodes can achieve 306.4 F/g at current density of 0.2 A/g in 1 M NaCl, which is higher than that (235.2 F/g) of activated carbon (AC) electrodes. Furthermore, a high electrosorption capacity of 8.75 mg g-1 in 100 mg/L NaCl was obtained with the Na@C electrodes in a batch-mode capacitive deionization cell. It exceeds the electrosorption capacity (4.08 mg g-1) of AC electrodes. The Na@C electrode also showed a promising cycle stability. The excellent performance of Na@C electrode for capacitive deionization (CDI) can be attributed to its high electrical conductivity and large accessible surface area.

Enzyme Sorption onto Soil and Biocarbon Amendments Alters Catalytic Capacity and Depends on the Specific Protein and pH

NASA Astrophysics Data System (ADS)

Foster, E.; Fogle, E. J.; Cotrufo, M. F.

2017-12-01

Enzymes catalyze biogeochemical reactions in soils and play a key role in nutrient cycling in agricultural systems. Often, to increase soil nutrients, agricultural managers add organic amendments and have recently experimented with charcoal-like biocarbon products. These amendments can enhance soil water and nutrient holding capacity through increasing porosity. However, the large surface area of the biocarbon has the potential to sorb nutrients and other organic molecules. Does the biocarbon decrease nutrient cycling through sorption of enzymes? In a laboratory setting, we compared the interaction of two purified enzymes β-glucosidase and acid phosphatase with a sandy clay loam and two biocarbons. We quantified the sorbed enzymes at three different pHs using a Bradford protein assay and then measured the activity of the sorbed enzyme via high-throughput fluorometric analysis. Both sorption and activity depended upon the solid phase, pH, and specific enzyme. Overall the high surface area biocarbon impacted the catalytic capacity of the enzymes more than the loam soil, which may have implications for soil nutrient management with these organic amendments.

Three-dimensional porous carbon composites containing high sulfur nanoparticle content for high-performance lithium–sulfur batteries

PubMed Central

Li, Guoxing; Sun, Jinhua; Hou, Wenpeng; Jiang, Shidong; Huang, Yong; Geng, Jianxin

2016-01-01

Sulfur is a promising cathode material for lithium–sulfur batteries because of its high theoretical capacity (1,675 mA h g−1); however, its low electrical conductivity and the instability of sulfur-based electrodes limit its practical application. Here we report a facile in situ method for preparing three-dimensional porous graphitic carbon composites containing sulfur nanoparticles (3D S@PGC). With this strategy, the sulfur content of the composites can be tuned to a high level (up to 90 wt%). Because of the high sulfur content, the nanoscale distribution of the sulfur particles, and the covalent bonding between the sulfur and the PGC, the developed 3D S@PGC cathodes exhibit excellent performance, with a high sulfur utilization, high specific capacity (1,382, 1,242 and 1,115 mA h g−1 at 0.5, 1 and 2 C, respectively), long cycling life (small capacity decay of 0.039% per cycle over 1,000 cycles at 2 C) and excellent rate capability at a high charge/discharge current. PMID:26830732

Cr{sub 2}O{sub 5} as new cathode for rechargeable sodium ion batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Feng, Xu-Yong; Chien, Po-Hsiu; Rose, Alyssa M.

2016-10-15

Chromium oxide, Cr{sub 2}O{sub 5}, was synthesized by pyrolyzing CrO{sub 3} at 350 °C and employed as a new cathode in rechargeable sodium ion batteries. Cr{sub 2}O{sub 5}/Na rechargeable batteries delivered high specific capacities up to 310 mAh/g at a current density of C/16 (or 20 mA/g). High-resolution solid-state {sup 23}Na NMR both qualitatively and quantitatively revealed the reversible intercalation of Na ions into the bulk electrode and participation of Na ions in the formation of the solid-electrolyte interphase largely at low potentials. Amorphization of the electrode structure occurred during the first discharge revealed by both NMR and X-ray diffractionmore » data. CrO{sub 3}-catalyzed electrolyte degradation and loss in electronic conductivity led to gradual capacity fading. The specific capacity stabilized at >120 mAh/g after 50 charge-discharge cycles. Further improvement in electrochemical performance is possible via electrode surface modification, polymer binder incorporation, or designs of new morphologies. - Graphical abstract: Electrochemical profile of a Cr{sub 2}O{sub 5}/Na battery cell and high-resolution solid-state {sup 23}Na MAS NMR spectrum of a Cr{sub 2}O{sub 5} electrode discharged to 2 V. - Highlights: • Cr{sub 2}O{sub 5} was synthesized and used as a new cathode in rechargeable Na ion batteries. • A high capacity of 310 mAh/g and an energy density of 564 Wh/kg were achieved. • High-resolution solid-state {sup 23}Na NMR was employed to follow the reaction mechanisms.« less

Single-crystalline LiFePO4 nanosheets for high-rate Li-ion batteries.

PubMed

Zhao, Yu; Peng, Lele; Liu, Borui; Yu, Guihua

2014-05-14

The lithiation/delithiation in LiFePO4 is highly anisotropic with lithium-ion diffusion being mainly confined to channels along the b-axis. Controlling the orientation of LiFePO4 crystals therefore plays an important role for efficient mass transport within this material. We report here the preparation of single crystalline LiFePO4 nanosheets with a large percentage of highly oriented {010} facets, which provide the highest pore density for lithium-ion insertion/extraction. The LiFePO4 nanosheets show a high specific capacity at low charge/discharge rates and retain significant capacities at high C-rates, which may benefit the development of lithium batteries with both favorable energy and power density.

Planning Decrements in Healthy Aging: Mediation Effects of Fluid Reasoning and Working Memory Capacity.

PubMed

Köstering, Lena; Leonhart, Rainer; Stahl, Christoph; Weiller, Cornelius; Kaller, Christoph P

2016-03-01

Although age-related differences in planning ability are well known, their cognitive foundations remain a matter of contention. To elucidate the specific processes underlying planning decrements in older age, the relative contributions of fluid reasoning, working memory (WM) capacity, and processing speed to accuracy on the Tower of London (TOL) planning task were investigated. Mediation analyses were used to relate overall and search depth-related TOL accuracy from older (N = 106; 60-89 years) and younger adults (N = 69; 18-54 years) to age and measures of fluid reasoning, WM capacity, and speed. For overall planning, fluid abilities mediated the effects of age, WM capacity, and speed in older adults. By contrast, fluid abilities and WM capacity mediated each other in younger adults. For planning accuracy under low demands on the depth of search, WM capacity was specifically important in older age, whereas younger adults recruited both WM capacity and fluid reasoning. Under high search-depth-demands, fluid abilities underlay the cognitive operations critical for resolving move interdependencies in both age groups. Fluid abilities and WM capacity undergo significant changes from younger to older age in their unique contribution to planning, which might represent a mechanism whereby planning decrements in older age are brought about. © The Author 2014. Published by Oxford University Press on behalf of The Gerontological Society of America. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Assembly of LiMnPO4 Nanoplates into Microclusters as a High-Performance Cathode in Lithium-Ion Batteries.

PubMed

Wang, Chao; Li, Shiheng; Han, Yuyao; Lu, Zhenda

2017-08-23

A novel structure of a carbon-coated LiMnPO 4 microcluster through emulsion-based self-assembly has been fabricated to yield a high-performance battery cathode. In this rational design, nanosized LiMnPO 4 plates are assembled into microclusters to achieve a dense packing and robust interparticle contact. In addition, the conductive carbon framework wrapping around these clusters functions as a fast electron highway, ensuring the high utilization of the active materials. The designed structure demonstrates enhanced specific capacity and cycling stability in lithium-ion batteries, delivering a discharge capacity of 120 mAh g -1 after 200 cycles at 0.2 C. It also shows a superior rate capability with discharge capacities of 139.7 mAh g -1 at 0.05 C, 131.7 mAh g -1 at 0.1 C, and 99.2 mAh g -1 at 1 C at room temperature.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Yandong; Zhang, Bingkai; Zheng, Jiaxin

Abstract. Due to the enhanced kinetic properties, nanocrystallites have received much attention as potential electrode materials for energy storage. However, because of the large specific surface areas of nanocrystallites, they usually suffer from decreased energy density, reduced cycling stability and total electrode capacity. In this work, we report a size-dependent excess capacity beyond the theoretical value of 170 mAhg-1 in a special carbon coated LiFePO4 composite cathode material, which delivers capacities of 191.2 and 213.5 mAhg-1 with the mean particle sizes of 83 nm and 42 nm, respectively. Moreover, this LiFePO4 composite also shows excellent cycling stability and high ratemore » performance. Our further experimental tests and ab initio calculations reveal that the excess capacity comes from the charge passivation for which the C-O-Fe bonds would lead to charge redistribution on the surface of LiFePO4 and hence to enhance the bonding interaction between surface O atoms and Li-ions. The surface reconstruction for excess Li-ion storage makes full use of the large specific surface area for the nanocrystallites, which can maintain the fast Li-ion transport and enhance the capacity greatly that the nanocrystallites usually suffers.« less

Electrospun nanofiber membranes for adsorption of dye molecules from textile wastewater

NASA Astrophysics Data System (ADS)

Akduman, C.; Akçakoca Kumbasar, E. P.; Morsunbul, S.

2017-10-01

The nanofiber membranes prepared by the electrospinning method have unique properties such as high specific surface area and high porosity with fine pores. These properties led electrospun nanofiber membranes to use for the removal of dye molecules from textile wastewater. In this study, a hydrophobic Thermoplastic Polyurethane (TPU) and a hydrophilic Poly (vinyl alcohol) (PVA) were selected for producing electrospun nanofibers and their sorption capacities were investigated. The largest sorption capacity reached to maximum 88.31 mg/g, belong to BTCA cross-linked PVA membranes due to hydrophilic character of PVA. Contrary to expectation, hydrophobic character of TPU was dominant and incorporation of CD to the TPU nanofibers did not affect the sorption of the TPU membranes, and showed very low adsorption capacity (14.48 mg/g).

Assessment of practices, capacities and incentives of poultry chain actors in implementation of highly pathogenic avian influenza mitigation measures in Ghana.

PubMed

Turkson, Paa Kobina; Okike, Iheanacho

2016-02-01

The animal health services-seeking behaviour of animal owners related to prevention and control of animal diseases may influence their decisions as to whether or not to use services provided by the public or private sectors. The specific objective of this paper was to assess the practices, capacities and incentives of actors involved in highly pathogenic avian influenza (HPAI) control to provide information for prevention and control in Ghana. Questionnaires were designed based on specific practices, incentives and capacities associated with each mitigation measure that was being assessed. Two peacetime preventive mitigation measures (biosecurity and reporting) and two outbreak containment measures (culling with compensation and movement control) were selected for evaluation. Supply chain actors were characterised based on baseline information. Tables were generated showing proportions of respondents in the various response categories in Likert-scale type itemised questionnaire. Mean scores (and their standard deviations) for the various actors with regard to mitigation measures were calculated. Pair-wise comparisons were done using t -ratio statistic and significance of differences were determined at a Bonferroni adjusted P -value of 0.0024. The study found statistically significant differences between certain actors for practices (biosecurity, reporting, culling and compensation and movement controls), incentives (reporting and movement control) and capacities (reporting and movement control). The findings provide lessons to help improve education and messages on HPAI and to help provide technical assistance targeted at specific actors to prevent and control future HPAI H5N1 outbreaks in Ghana.

Facile Synthesis of Layer Structured GeP3/C with Stable Chemical Bonding for Enhanced Lithium-Ion Storage

NASA Astrophysics Data System (ADS)

Qi, Wen; Zhao, Haihua; Wu, Ying; Zeng, Hong; Tao, Tao; Chen, Chao; Kuang, Chunjiang; Zhou, Shaoxiong; Huang, Yunhui

2017-02-01

Recently, metal phosphides have been investigated as potential anode materials because of higher specific capacity compared with those of carbonaceous materials. However, the rapid capacity fade upon cycling leads to poor durability and short cycle life, which cannot meet the need of lithium-ion batteries with high energy density. Herein, we report a layer-structured GeP3/C nanocomposite anode material with high performance prepared by a facial and large-scale ball milling method via in-situ mechanical reaction. The P-O-C bonds are formed in the composite, leading to close contact between GeP3 and carbon. As a result, the GeP3/C anode displays excellent lithium storage performance with a high reversible capacity up to 1109 mA h g-1 after 130 cycles at a current density of 0.1 A g-1. Even at high current densities of 2 and 5 A g-1, the reversible capacities are still as high as 590 and 425 mA h g-1, respectively. This suggests that the GeP3/C composite is promising to achieve high-energy lithium-ion batteries and the mechanical milling is an efficient method to fabricate such composite electrode materials especially for large-scale application.

Enhanced kinetics of polysulfide redox reactions on Mo2C/CNT in lithium-sulfur batteries.

PubMed

Razaq, Rameez; Sun, Dan; Xin, Ying; Li, Qian; Huang, Taizhong; Zheng, Lei; Zhang, Zhaoliang; Huang, Yunhui

2018-07-20

Among different energy storage devices, the lithium-sulfur (Li-S) battery is the subject of recent attention. However, the capacity decay caused by polysulfide shuttle leading to sluggish kinetics of polysulfide redox reactions is the main hindrance for its practical application in Li-S batteries. Herein, molybdenum carbide nanoparticles anchored on carbon nanotubes (Mo 2 C/CNT) are reported to serve as an efficient cathode material to enhance the electrochemical kinetics of polysulfide conversion in Li-S batteries. Mo 2 C/CNT shows strong adsorption and activation of polar polysulfides and therefore accelerates the redox kinetics of polysulfides, reduces the energy barrier, effectively mitigates the polarization and polysulfide shuttle, thus improving the electrochemical performance. The S-Mo 2 C/CNT composite with 70 wt% sulfur loading exhibits high specific discharge capacity (1206 mA h g -1 at 0.5 C), excellent high-rate performance, long cycle life (900 cycles), and outstanding Coulombic efficiency (∼100%) at a high rate (2 C) corresponding to a capacity decay of only 0.05%. Remarkably, the S-Mo 2 C/CNT cathode with high areal sulfur loading of 2.5 mg cm -2 exhibits high-rate capacities and stable cycling performance over 100 cycles, offering the potential for use in high energy Li-S batteries.

Enhanced kinetics of polysulfide redox reactions on Mo2C/CNT in lithium–sulfur batteries

NASA Astrophysics Data System (ADS)

Razaq, Rameez; Sun, Dan; Xin, Ying; Li, Qian; Huang, Taizhong; Zheng, Lei; Zhang, Zhaoliang; Huang, Yunhui

2018-07-01

Among different energy storage devices, the lithium–sulfur (Li–S) battery is the subject of recent attention. However, the capacity decay caused by polysulfide shuttle leading to sluggish kinetics of polysulfide redox reactions is the main hindrance for its practical application in Li–S batteries. Herein, molybdenum carbide nanoparticles anchored on carbon nanotubes (Mo2C/CNT) are reported to serve as an efficient cathode material to enhance the electrochemical kinetics of polysulfide conversion in Li–S batteries. Mo2C/CNT shows strong adsorption and activation of polar polysulfides and therefore accelerates the redox kinetics of polysulfides, reduces the energy barrier, effectively mitigates the polarization and polysulfide shuttle, thus improving the electrochemical performance. The S-Mo2C/CNT composite with 70 wt% sulfur loading exhibits high specific discharge capacity (1206 mA h g‑1 at 0.5 C), excellent high-rate performance, long cycle life (900 cycles), and outstanding Coulombic efficiency (∼100%) at a high rate (2 C) corresponding to a capacity decay of only 0.05%. Remarkably, the S-Mo2C/CNT cathode with high areal sulfur loading of 2.5 mg cm‑2 exhibits high-rate capacities and stable cycling performance over 100 cycles, offering the potential for use in high energy Li–S batteries.

Fe-Catalyzed Synthesis of Porous Carbons Spheres with High Graphitization Degree for High-Performance Supercapacitors

NASA Astrophysics Data System (ADS)

Zhu, Jun; Shi, Hongwei; Zhuo, Xin; Hu, Yalin

2017-10-01

We have developed a facile and efficient Fe-catalyzed method for fabrication of porous carbons spheres with high graphitization degree (GNPCs) using glucose as carbon precursor at relatively low carbonization temperature. GNPCs not only have relatively large accessible ion surface area to accommodate greater capacity but also high graphitization degree to accelerate ion diffusion. As a typical application, we demonstrate that GNPCs exhibit excellent electrochemical performance for use in supercapacitors, with high specific capacity of 150.6 F g-1 at current density of 1 A g-1 and good rate capability and superior cycling stability over 10,000 cycles, confirming their potential application for energy storage. Moreover, it is believed that this method offers a new strategy for synthesis of porous carbons with high graphitization degree.

Synthesis of three-dimensionally interconnected sulfur-rich polymers for cathode materials of high-rate lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Kim, Hoon; Lee, Joungphil; Ahn, Hyungmin; Kim, Onnuri; Park, Moon Jeong

2015-06-01

Elemental sulfur is one of the most attractive cathode active materials in lithium batteries because of its high theoretical specific capacity. Despite the positive aspect, lithium-sulfur batteries have suffered from severe capacity fading and limited rate capability. Here we report facile large-scale synthesis of a class of organosulfur compounds that could open a new chapter in designing cathode materials to advance lithium-sulfur battery technologies. Porous trithiocyanuric acid crystals are synthesized for use as a soft template, where the ring-opening polymerization of elemental sulfur takes place along the thiol surfaces to create three-dimensionally interconnected sulfur-rich phases. Our lithium-sulfur cells display discharge capacity of 945 mAh g-1 after 100 cycles at 0.2 C with high-capacity retention of 92%, as well as lifetimes of 450 cycles. Particularly, the organized amine groups in the crystals increase Li+-ion transfer rate, affording a rate performance of 1210, mAh g-1 at 0.1 C and 730 mAh g-1 at 5 C.

Synthesis of three-dimensionally interconnected sulfur-rich polymers for cathode materials of high-rate lithium–sulfur batteries

PubMed Central

Kim, Hoon; Lee, Joungphil; Ahn, Hyungmin; Kim, Onnuri; Park, Moon Jeong

2015-01-01

Elemental sulfur is one of the most attractive cathode active materials in lithium batteries because of its high theoretical specific capacity. Despite the positive aspect, lithium–sulfur batteries have suffered from severe capacity fading and limited rate capability. Here we report facile large-scale synthesis of a class of organosulfur compounds that could open a new chapter in designing cathode materials to advance lithium–sulfur battery technologies. Porous trithiocyanuric acid crystals are synthesized for use as a soft template, where the ring-opening polymerization of elemental sulfur takes place along the thiol surfaces to create three-dimensionally interconnected sulfur-rich phases. Our lithium–sulfur cells display discharge capacity of 945 mAh g−1 after 100 cycles at 0.2 C with high-capacity retention of 92%, as well as lifetimes of 450 cycles. Particularly, the organized amine groups in the crystals increase Li+-ion transfer rate, affording a rate performance of 1210, mAh g−1 at 0.1 C and 730 mAh g−1 at 5 C. PMID:26065407

Are soil carbon models transferable across distinct regions or scales in Florida?

USDA-ARS?s Scientific Manuscript database

Some Florida soils have great capacity to accumulate carbon due to unique geographical and topographical conditions (high net primary productivity, precipitation, high water table, and flat topography). Soil carbon models have been used to quantify the carbon pools usually at a specific scale or in ...

Effects of coal storage in air on physical and chemical properties of coal and on gas adsorption

USGS Publications Warehouse

Mastalerz, Maria; Solano-Acosta, W.; Schimmelmann, A.; Drobniak, A.

2009-01-01

This paper investigates changes in the high-volatile bituminous Lower Block Coal Member from Indiana owing to moisture availability and oxidation in air at ambient pressure and temperature over storage time. Specifically, it investigates changes in chemistry, in surface area, and pore structure, as well as changes in methane and carbon dioxide adsorption capacities. Our results document that the methane adsorption capacity increased by 40%, whereas CO2 adsorption capacity increased by 18% during a 13-month time period. These changes in adsorption are accompanied by changes in chemistry and surface area of the coal. The observed changes in adsorption capacity indicate that special care must be taken when collecting samples and preserving coals until adsorption characteristics are measured in the laboratory. High-pressure isotherms from partially dried coal samples would likely cause overestimation of gas adsorption capacities, lead to a miscalculation of coal-bed methane prospects, and provide deceptively optimistic prognoses for recovery of coal-bed methane or capture of anthropogenic CO2. ?? 2009 Elsevier B.V. All rights reserved.

Effect of surface hydroxyl groups on heat capacity of mesoporous silica

NASA Astrophysics Data System (ADS)

Marszewski, Michal; Butts, Danielle; Lan, Esther; Yan, Yan; King, Sophia C.; McNeil, Patricia E.; Galy, Tiphaine; Dunn, Bruce; Tolbert, Sarah H.; Hu, Yongjie; Pilon, Laurent

2018-05-01

This paper quantifies the effect of surface hydroxyl groups on the effective specific and volumetric heat capacities of mesoporous silica. To achieve a wide range of structural diversity, mesoporous silica samples were synthesized by various methods, including (i) polymer-templated nanoparticle-based powders, (ii) polymer-templated sol-gel powders, and (iii) ambigel silica samples dried by solvent exchange at room temperature. Their effective specific heat capacity, specific surface area, and porosity were measured using differential scanning calorimetry and low-temperature nitrogen adsorption-desorption measurements. The experimentally measured specific heat capacity was larger than the conventional weight-fraction-weighted specific heat capacity of the air and silica constituents. The difference was attributed to the presence of OH groups in the large internal surface area. A thermodynamic model was developed based on surface energy considerations to account for the effect of surface OH groups on the specific and volumetric heat capacity. The model predictions fell within the experimental uncertainty.

High capacity of lithium-sulfur batteries at low electrolyte/sulfur ratio enabled by an organosulfide containing electrolyte

DOE PAGES

Chen, Shuru; Gao, Yue; Yu, Zhaoxin; ...

2016-11-30

We present that lithium-sulfur (Li-S) battery is a promising energy storage technology to replace lithium ion batteries for higher energy density and lower cost. Dissolution of lithium polysulfide intermediates in conventional Li-S electrolytes is known as one of the key technical barriers to the development of Li-S, because it promotes redistribution and irreversible deposition of Li 2S, and also forces large amounts of electrolyte to be used, shortening cycling life and driving down cell energy density. Recently, dimethyl disulfide as a functional co-solvent has been demonstrated to show an alternate electrochemical reaction pathway for sulfur cathodes by the formation ofmore » dimethyl polysulfides and lithium organosulfides as intermediates and reduction products. In this work, comprehensive studies show that this new pathway not only provides high capacity but also enables excellent capacity retention through a built-in automatic discharge shutoff mechanism by tuning carbon/sulfur ratio in sulfur cathodes to reduce unfavorable Li 2S formation. Furthermore, this new electrolyte system is also found to enable high capacity of high-sulfur-loading cathodes with low electrolyte/sulfur (E/S) ratios, such as a stable specific capacity of around 1000 mAh g -1 using a low electrolyte amount (i.e, E/S ratio of 5 mL g -1) and highsulfur-loading (4 mg cm -2) cathodes. This electrolyte system almost doubles the capacity obtained with conventional electrolytes under the same harsh conditions. In conclusion, these results highlight the practical potential of this electrolyte system to enable high-energy-density Li-S batteries.« less

High capacity of lithium-sulfur batteries at low electrolyte/sulfur ratio enabled by an organosulfide containing electrolyte

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Shuru; Gao, Yue; Yu, Zhaoxin

We present that lithium-sulfur (Li-S) battery is a promising energy storage technology to replace lithium ion batteries for higher energy density and lower cost. Dissolution of lithium polysulfide intermediates in conventional Li-S electrolytes is known as one of the key technical barriers to the development of Li-S, because it promotes redistribution and irreversible deposition of Li 2S, and also forces large amounts of electrolyte to be used, shortening cycling life and driving down cell energy density. Recently, dimethyl disulfide as a functional co-solvent has been demonstrated to show an alternate electrochemical reaction pathway for sulfur cathodes by the formation ofmore » dimethyl polysulfides and lithium organosulfides as intermediates and reduction products. In this work, comprehensive studies show that this new pathway not only provides high capacity but also enables excellent capacity retention through a built-in automatic discharge shutoff mechanism by tuning carbon/sulfur ratio in sulfur cathodes to reduce unfavorable Li 2S formation. Furthermore, this new electrolyte system is also found to enable high capacity of high-sulfur-loading cathodes with low electrolyte/sulfur (E/S) ratios, such as a stable specific capacity of around 1000 mAh g -1 using a low electrolyte amount (i.e, E/S ratio of 5 mL g -1) and highsulfur-loading (4 mg cm -2) cathodes. This electrolyte system almost doubles the capacity obtained with conventional electrolytes under the same harsh conditions. In conclusion, these results highlight the practical potential of this electrolyte system to enable high-energy-density Li-S batteries.« less

Enhanced electrochemical performance from 3DG/LiFePO4/G sandwich cathode material

NASA Astrophysics Data System (ADS)

Du, Yahui; Tang, Yufeng; Chang, Chengkang

2017-08-01

In this paper, we have successfully synthesized a three dimensional graphene/LiFePO4/graphene (3DG/LFP/G) sandwich composite by an in-situ hydrothermal method, in which chemical vapor deposited 3D graphene acts as the high conductivity supporting framework, while the LiFePO4 nanoparticles are anchored onto the 3D graphene framework covered by graphene sheets. XRD and SEM results confirmed the formation of the 3DG/LFP/G sandwich composite. Cyclic Voltammetry curve of the sandwich composite shows sharper redox peaks and reduced voltage separation when compared to the reference electrodes, suggesting high specific capacity and good rate performance. Further charge/discharge measurements presented high capacity of 164 mAh g-1 at 0.2 C and 124 mAh g-1 at 10 C (75.7% of its initial capacity) for the sandwich composite, with capacity retention of 95.7% after 100 cycles, implying potential application in lithium ion battery at high rates. The EIS investigation suggests that both the electronic conductivity and the Li ion diffusion are promoted by the underlined 3D graphene framework, which is regarded as the reason for the enhanced electrochemical performance.

An Amorphous Carbon Nitride Composite Derived from ZIF-8 as Anode Material for Sodium-Ion Batteries.

PubMed

Fan, Jing-Min; Chen, Jia-Jia; Zhang, Qian; Chen, Bin-Bin; Zang, Jun; Zheng, Ming-Sen; Dong, Quan-Feng

2015-06-08

An composite comprising amorphous carbon nitride (ACN) and zinc oxide is derived from ZIF-8 by pyrolysis. The composite is a promising anode material for sodium-ion batteries. The nitrogen content of the ACN composite is as high as 20.4 %, and the bonding state of nitrogen is mostly pyridinic, as determined by X-ray photoelectron spectroscopy (XPS). The composite exhibits an excellent Na(+) storage performance with a reversible capacity of 430 mA h g(-1) and 146 mA h g(-1) at current densities of 83 mA g(-1) and 8.33 A g(-1) , respectively. A specific capacity of 175 mA h g(-1) was maintained after 2000 cycles at 1.67 A g(-1) , with only 0.016 % capacity degradation per cycle. Moreover, an accelerating rate calorimetry (ARC) test demonstrates the excellent thermal stability of the composite, with a low self heating rate and high onset temperature (210 °C). These results shows its promise as a candidate material for high-capacity, high-rate anodes for sodium-ion batteries. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Microwave-Assisted Synthesis of NiCo2O4 Double-Shelled Hollow Spheres for High-Performance Sodium Ion Batteries

NASA Astrophysics Data System (ADS)

Zhang, Xiong; Zhou, Yanping; Luo, Bin; Zhu, Huacheng; Chu, Wei; Huang, Kama

2018-03-01

The ternary transitional metal oxide NiCo2O4 is a promising anode material for sodium ion batteries due to its high theoretical capacity and superior electrical conductivity. However, its sodium storage capability is severely limited by the sluggish sodiation/desodiation reaction kinetics. Herein, NiCo2O4 double-shelled hollow spheres were synthesized via a microwave-assisted, fast solvothermal synthetic procedure in a mixture of isopropanol and glycerol, followed by annealing. Isopropanol played a vital role in the precipitation of nickel and cobalt, and the shrinkage of the glycerol quasi-emulsion under heat treatment was responsible for the formation of the double-shelled nanostructure. The as-synthesized product was tested as an anode material in a sodium ion battery, was found to exhibit a high reversible specific capacity of 511 mAh g-1 at 100 mA g-1, and deliver high capacity retention after 100 cycles. [Figure not available: see fulltext.

One-Dimensional Cu2- xSe Nanorods as the Cathode Material for High-Performance Aluminum-Ion Battery.

PubMed

Jiang, Jiali; Li, He; Fu, Tao; Hwang, Bing-Joe; Li, Xue; Zhao, Jinbao

2018-05-30

In this work, nonstoichiometric Cu 2- x Se fabricated by a facile water evaporation process is used as high-performance Al-ion battery cathode materials. Cu 2- x Se electrodes show high reversible capacity and excellent cycling stability, even at a high current density of 200 mA g -1 , the specific charge capacity in the initial cycle is 241 mA h g -1 and maintains 100 mA h g -1 after 100 cycles with a Coulombic efficiency of 96.1%, showing good capacity retention. The prominent kinetics of Cu 2- x Se electrodes is also revealed by the GITT, which is attributed to the ultrahigh electronic conductivity of the Cu 2- x Se material. Most importantly, an extensive research is dedicated to investigating the detailed intercalation and de-intercalation of relatively large chloroaluminate anions into the cubic Cu 2- x Se, which is conducive to better understand the reaction mechanism of the Al/Cu 2- x Se battery.

Anomalous electronic heat capacity of copper nanowires at sub-Kelvin temperatures

NASA Astrophysics Data System (ADS)

Viisanen, K. L.; Pekola, J. P.

2018-03-01

We have measured the electronic heat capacity of thin film nanowires of copper and silver at temperatures 0.1-0.3 K; the films were deposited by standard electron-beam evaporation. The specific heat of the Ag films of sub-100-nm thickness agrees with the bulk value and the free-electron estimate, whereas that of similar Cu films exceeds the corresponding reference values by one order of magnitude. The origin of the anomalously high heat capacity of copper films remains unknown for the moment. Based on the small heat capacity at low temperatures and the possibility to devise a tunnel probe thermometer on it, metal films form a promising absorber material, e.g., for microwave photon calorimetry.

A multi-sector assessment of community organizational capacity for promotion of Chinese immigrant worker health.

PubMed

Tsai, Jenny H-C; Thompson, Elaine A

2017-12-01

Community-based collaborative approaches have received increased attention as a means for addressing occupational health disparities. Organizational capacity, highly relevant to engaging and sustaining community partnerships, however, is rarely considered in occupational health research. To characterize community organizational capacity specifically relevant to Chinese immigrant worker health, we used a cross-sectional, descriptive design with 36 agencies from six community sectors in King County, Washington. Joint interviews, conducted with two representatives from each agency, addressed three dimensions of organizational capacity: organizational commitment, resources, and flexibility. Descriptive statistics were used to capture the patterning of these dimensions by community sector. Organizational capacity varied widely across and within sectors. Chinese and Pan-Asian service sectors indicated higher capacity for Chinese immigrant worker health than did Chinese faith-based, labor union, public, and Pan-ethnic nonprofit sectors. Variation in organizational capacity in community sectors can inform selection of collaborators for community-based, immigrant worker health interventions. © 2017 Wiley Periodicals, Inc.

A high-performance ternary Si composite anode material with crystal graphite core and amorphous carbon shell

NASA Astrophysics Data System (ADS)

Sui, Dong; Xie, Yuqing; Zhao, Weimin; Zhang, Hongtao; Zhou, Ying; Qin, Xiting; Ma, Yanfeng; Yang, Yong; Chen, Yongsheng

2018-04-01

Si is a promising anode material for lithium-ion batteries, but suffers from sophisticated engineering structures and complex fabrication processes that pose challenges for commercial application. Herein, a ternary Si/graphite/pyrolytic carbon (SiGC) anode material with a structure of crystal core and amorphous shell using low-cost raw materials is developed. In this ternary SiGC composite, Si component exists as nanoparticles and is spread on the surface of the core graphite flakes while the sucrose-derived pyrolytic carbon further covers the graphite/Si components as the amorphous shell. With this structure, Si together with the graphite contributes to the high specific capacity of this Si ternary material. Also the graphite serves as the supporting and conducting matrix and the amorphous shell carbon could accommodate the volume change effect of Si, reinforces the integrity of the composite architecture, and prevents the graphite and Si from direct exposing to the electrolyte. The optimized ternary SiGC composite displays high reversible specific capacity of 818 mAh g-1 at 0.1 A g-1, initial Coulombic efficiency (CE) over 80%, and excellent cycling stability at 0.5 A g-1 with 83.6% capacity retention (∼610 mAh g-1) after 300 cycles.

Simple synthesis of highly catalytic carbon-free MnCo2O4@Ni as an oxygen electrode for rechargeable Li–O2 batteries with long-term stability

PubMed Central

Kalubarme, Ramchandra S.; Jadhav, Harsharaj S.; Ngo, Duc Tung; Park, Ga-Eun; Fisher, John G.; Choi, Yun-Il; Ryu, Won-Hee; Park, Chan-Jin

2015-01-01

An effective integrated design with a free standing and carbon-free architecture of spinel MnCo2O4 oxide prepared using facile and cost effective hydrothermal method as the oxygen electrode for the Li–O2 battery, is introduced to avoid the parasitic reactions of carbon and binder with discharge products and reaction intermediates, respectively. The highly porous structure of the electrode allows the electrolyte and oxygen to diffuse effectively into the catalytically active sites and hence improve the cell performance. The amorphous Li2O2 will then precipitate and decompose on the surface of free-standing catalyst nanorods. Electrochemical examination demonstrates that the free-standing electrode without carbon support gives the highest specific capacity and the minimum capacity fading among the rechargeable Li–O2 batteries tested. The Li-O2 cell has demonstrated a cyclability of 119 cycles while maintaining a moderate specific capacity of 1000 mAh g−1. Furthermore, the synergistic effect of the fast kinetics of electron transport provided by the free-standing structure and the high electro-catalytic activity of the spinel oxide enables excellent performance of the oxygen electrode for Li-O2 cells. PMID:26292965

Tailoring Anisotropic Li-Ion Transport Tunnels on Orthogonally Arranged Li-Rich Layered Oxide Nanoplates Toward High-Performance Li-Ion Batteries.

PubMed

Xu, Ming; Fei, Linfeng; Zhang, Weibing; Li, Tao; Lu, Wei; Zhang, Nian; Lai, Yanqing; Zhang, Zhian; Fang, Jing; Zhang, Kai; Li, Jie; Huang, Haitao

2017-03-08

High-performance Li-rich layered oxide (LRLO) cathode material is appealing for next-generation Li-ion batteries owing to its high specific capacity (>300 mAh g -1 ). Despite intense studies in the past decade, the low initial Coulombic efficiency and unsatisfactory cycling stability of LRLO still remain as great challenges for its practical applications. Here, we report a rational design of the orthogonally arranged {010}-oriented LRLO nanoplates with built-in anisotropic Li + ion transport tunnels. Such a novel structure enables fast Li + ion intercalation and deintercalation kinetics and enhances structural stability of LRLO. Theoretical calculations and experimental characterizations demonstrate the successful synthesis of target cathode material that delivers an initial discharge capacity as high as 303 mAh g -1 with an initial Coulombic efficiency of 93%. After 200 cycles at 1.0 C rate, an excellent capacity retention of 92% can be attained. Our method reported here opens a door to the development of high-performance Ni-Co-Mn-based cathode materials for high-energy density Li-ion batteries.

Long-life Li/polysulphide batteries with high sulphur loading enabled by lightweight three-dimensional nitrogen/sulphur-codoped graphene sponge

PubMed Central

Zhou, Guangmin; Paek, Eunsu; Hwang, Gyeong S.; Manthiram, Arumugam

2015-01-01

Lithium–sulphur batteries with a high theoretical energy density are regarded as promising energy storage devices for electric vehicles and large-scale electricity storage. However, the low active material utilization, low sulphur loading and poor cycling stability restrict their practical applications. Herein, we present an effective strategy to obtain Li/polysulphide batteries with high-energy density and long-cyclic life using three-dimensional nitrogen/sulphur codoped graphene sponge electrodes. The nitrogen/sulphur codoped graphene sponge electrode provides enough space for a high sulphur loading, facilitates fast charge transfer and better immobilization of polysulphide ions. The hetero-doped nitrogen/sulphur sites are demonstrated to show strong binding energy and be capable of anchoring polysulphides based on first-principles calculations. As a result, a high specific capacity of 1,200 mAh g−1 at 0.2C rate, a high-rate capacity of 430 mAh g−1 at 2C rate and excellent cycling stability for 500 cycles with ∼0.078% capacity decay per cycle are achieved. PMID:26182892

Electrodeposited binder-free NiCo2O4@carbon nanofiber as a high performance anode for lithium ion batteries

NASA Astrophysics Data System (ADS)

Zhang, Jie; Chu, Ruixia; Chen, Yanli; Jiang, Heng; Zhang, Ying; Huang, Nay Ming; Guo, Hang

2018-03-01

Binder-free nickel cobaltite on a carbon nanofiber (NiCo2O4@CNF) anode for lithium ion batteries was prepared via a two-step procedure of electrospinning and electrodeposition. The CNF was obtained by annealing electrospun poly-acrylonitrile (PAN) in nitrogen (N2). The NiCo2O4 nanostructures were then grown on the CNF by electrodeposition, followed by annealing in air. Experimental results showed that vertically aligned NiCo2O4 nanosheets had uniformly grown on the surface of the CNF, forming an interconnected network. The NiCo2O4@CNF possessed considerable lithium storage capacity and cycling stability. It exhibited a high reversible capacity of 778 mAhg-1 after 300 cycles at a current density of 0.25 C (1 C = 890 mAg-1) with an average capacity loss rate of 0.05% per cycle. The NiCo2O4@CNF had considerable rate capacities, delivering a capacity of 350 mAhg-1 at a current density of 2.0 C. The outstanding electrochemical performance can be mainly attributed to the following: (1) The nanoscale structure of NiCo2O4 could not only shorten the diffusion path of lithium ions and electrons but also increase the specific surface area, providing more active sites for electrochemical reactions. (2) The CNF with considerable mechanical strength and electrical conductivity could function as an anchor for the NiCo2O4 nanostructure and ensure an efficient electron transfer. (3) The porous structure resulted in a high specific surface area and an effective buffer for the volume changes during the repeated charge-discharge processes. Compared with a conventional hydrothermal method, electrodeposition could significantly simplify the preparation of NiCo2O4, with a shorter preparation period and lower energy consumption. This work provides an alternative strategy to obtain a high performance anode for lithium ion batteries.

Toward Theoretically Cycling-Stable Lithium-Sulfur Battery Using a Foldable and Compositionally Heterogeneous Cathode.

PubMed

Zhong, Lei; Yang, Kai; Guan, Ruiteng; Wang, Liangbin; Wang, Shuanjin; Han, Dongmei; Xiao, Min; Meng, Yuezhong

2017-12-20

Rechargeable lithium-sulfur (Li-S) batteries have been expected for new-generation electrical energy storages, which are attributed to their high theoretical energy density, cost effectiveness, and eco-friendliness. But Li-S batteries still have some problems for practical application, such as low sulfur utilization and dissatisfactory capacity retention. Herein, we designed and fabricated a foldable and compositionally heterogeneous three-dimensional sulfur cathode with integrated sandwich structure. The electrical conductivity of the cathode is facilitated by three different dimension carbons, in which short-distance and long-distance pathways for electrons are provided by zero-dimensional ketjen black (KB), one-dimensional activated carbon fiber (ACF) and two-dimensional graphene (G). The resultant three-dimensional sulfur cathode (T-AKG/KB@S) with an areal sulfur loading of 2 mg cm -2 exhibits a high initial specific capacity, superior rate performance and a reversible discharge capacity of up to 726 mAh g -1 at 3.6 mA cm -2 with an inappreciable capacity fading rate of 0.0044% per cycle after 500 cycles. Moreover, the cathode with a high areal sulfur loading of 8 mg cm -2 also delivers a reversible discharge capacity of 938 mAh g -1 at 0.71 mA cm -2 with a capacity fading rate of 0.15% per cycle and a Coulombic efficiency of almost 100% after 50 cycles.

40 CFR 98.468 - Definitions.

Code of Federal Regulations, 2013 CFR

2013-07-01

... design capacity, the calculation must include a site-specific density. If the design capacity is within... process that can reasonably be expected to change the site-specific waste density, the site-specific waste density must be redetermined and the design capacity must be recalculated based on the new waste density...

40 CFR 98.468 - Definitions.

Code of Federal Regulations, 2012 CFR

2012-07-01

... design capacity, the calculation must include a site-specific density. If the design capacity is within... process that can reasonably be expected to change the site-specific waste density, the site-specific waste density must be redetermined and the design capacity must be recalculated based on the new waste density...

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard

Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at leastmore » 5 mAh/cm.sup.2 at a C-rate of C/2.« less

Ternary manganese ferrite/graphene/polyaniline nanostructure with enhanced electrochemical capacitance performance

NASA Astrophysics Data System (ADS)

Xiong, Pan; Hu, Chenyao; Fan, Ye; Zhang, Wenyao; Zhu, Junwu; Wang, Xin

2014-11-01

A ternary manganese ferrite/graphene/polyaniline (MGP) nanostructure is designed and synthesized via a facile two-step approach. This nanostructure exhibits outstanding electrochemical performances, such as high specific capacitance (454.8 F g-1 at 0.2 A g-1), excellent rate capability (75.8% capacity retention at 5 A g-1), and good cycling stability (76.4% capacity retention after 5000 cycles at 2 A g-1), which are superior to those of its individual components (manganese ferrite, reduced-graphene oxide, polyaniline) and corresponding binary hybrids (manganese ferrite/graphene (MG), manganese ferrite/polyaniline (MP), and graphene/polyaniline (GP)). A symmetric supercapacitor device using the as-obtained hybrid has been fabricated and tested. The device exhibits a high specific capacitance of 307.2 F g-1 at 0.1 A g-1 with a maximum energy density of 13.5 W h kg-1. The high electrochemical performance of ternary MGP can be attributed to its well-designed nanostructure and the synergistic effect of the individual components.

Ultrafast Charging High Capacity Asphalt-Lithium Metal Batteries.

PubMed

Wang, Tuo; Villegas Salvatierra, Rodrigo; Jalilov, Almaz S; Tian, Jian; Tour, James M

2017-11-28

Li metal has been considered an outstanding candidate for anode materials in Li-ion batteries (LIBs) due to its exceedingly high specific capacity and extremely low electrochemical potential, but addressing the problem of Li dendrite formation has remained a challenge for its practical rechargeable applications. In this work, we used a porous carbon material made from asphalt (Asp), specifically untreated gilsonite, as an inexpensive host material for Li plating. The ultrahigh surface area of >3000 m 2 /g (by BET, N 2 ) of the porous carbon ensures that Li was deposited on the surface of the Asp particles, as determined by scanning electron microscopy, to form Asp-Li. Graphene nanoribbons (GNRs) were added to enhance the conductivity of the host material at high current densities, to produce Asp-GNR-Li. Asp-GNR-Li has demonstrated remarkable rate performance from 5 A/g Li (1.3C) to 40 A/g Li (10.4C) with Coulombic efficiencies >96%. Stable cycling was achieved for more than 500 cycles at 5 A/g Li , and the areal capacity reached up to 9.4 mAh/cm 2 at a highest discharging/charging rate of 20 mA/cm 2 that was 10× faster than that of typical LIBs, suggesting use in ultrafast charging systems. Full batteries were also built combining the Asp-GNR-Li anodes with a sulfurized carbon cathode that possessed both high power density (1322 W/kg) and high energy density (943 Wh/kg).

Carbon-Coated Honeycomb Ni-Mn-Co-O Inverse Opal: A High Capacity Ternary Transition Metal Oxide Anode for Li-ion Batteries

PubMed Central

McNulty, David; Geaney, Hugh; O’Dwyer, Colm

2017-01-01

We present the formation of a carbon-coated honeycomb ternary Ni-Mn-Co-O inverse opal as a conversion mode anode material for Li-ion battery applications. In order to obtain high capacity via conversion mode reactions, a single phase crystalline honeycombed IO structure of Ni-Mn-Co-O material was first formed. This Ni-Mn-Co-O IO converts via reversible redox reactions and Li2O formation to a 3D structured matrix assembly of nanoparticles of three (MnO, CoO and NiO) oxides, that facilitates efficient reactions with Li. A carbon coating maintains the structure without clogging the open-worked IO pore morphology for electrolyte penetration and mass transport of products during cycling. The highly porous IO was compared in a Li-ion half-cell to nanoparticles of the same material and showed significant improvement in specific capacity and capacity retention. Further optimization of the system was investigated by incorporating a vinylene carbonate additive into the electrolyte solution which boosted performance, offering promising high-rate performance and good capacity retention over extended cycling. The analysis confirms the possibility of creating a ternary transition metal oxide material with binder free accessible open-worked structure to allow three conversion mode oxides to efficiently cycle as an anode material for Li-ion battery applications. PMID:28186183

Carbon-Coated Honeycomb Ni-Mn-Co-O Inverse Opal: A High Capacity Ternary Transition Metal Oxide Anode for Li-ion Batteries.

PubMed

McNulty, David; Geaney, Hugh; O'Dwyer, Colm

2017-02-10

We present the formation of a carbon-coated honeycomb ternary Ni-Mn-Co-O inverse opal as a conversion mode anode material for Li-ion battery applications. In order to obtain high capacity via conversion mode reactions, a single phase crystalline honeycombed IO structure of Ni-Mn-Co-O material was first formed. This Ni-Mn-Co-O IO converts via reversible redox reactions and Li 2 O formation to a 3D structured matrix assembly of nanoparticles of three (MnO, CoO and NiO) oxides, that facilitates efficient reactions with Li. A carbon coating maintains the structure without clogging the open-worked IO pore morphology for electrolyte penetration and mass transport of products during cycling. The highly porous IO was compared in a Li-ion half-cell to nanoparticles of the same material and showed significant improvement in specific capacity and capacity retention. Further optimization of the system was investigated by incorporating a vinylene carbonate additive into the electrolyte solution which boosted performance, offering promising high-rate performance and good capacity retention over extended cycling. The analysis confirms the possibility of creating a ternary transition metal oxide material with binder free accessible open-worked structure to allow three conversion mode oxides to efficiently cycle as an anode material for Li-ion battery applications.

Conformal spinel/layered heterostructures of Co3O4 shells grown on single-crystal Li-rich nanoplates for high-performance lithium-ion batteries

NASA Astrophysics Data System (ADS)

Xin, Yue; Lan, Xiwei; Chang, Peng; Huang, Yaqun; Wang, Libin; Hu, Xianluo

2018-07-01

Lithium-rich layered materials have received much attention because of their high specific capacity and high energy density. Unfortunately, they suffer from irreversible capacity loss, low initial Coulombic efficiency and poor cyclability. Here we report a facile co-precipitation method to synthesize uniform single-crystal Li-rich Li[Li0.2Mn0.54Ni0.13Co0.13]O2 nanoplates without using any template. Subsequently, a Co3O4 shell is in situ grown on the Li-rich nanoplates through a hydrothermal method, leading to spinel/layered heterostructures. The electrode made of conformal heterostructured Li-rich/Co3O4 nanoplates delivers a high discharge capacity of 296 mA h g-1 at 0.1 C with an initial Coulombic efficiency of 84%. The capacity retention reaches 83.2% with a discharge capacity of 223 mA h g-1 after 160 cycles at 0.2 C during the potential window ranging from 2.0 to 4.8 V. The enhanced electrochemical performance of the resulting Li-rich/Co3O4 nanoplates benefits from the unique conformal heterostructure as well as the electrochemically active LixCoOy generated between the reaction of Co3O4 shells and the extracted Li2O during charging/discharging processes.

Comparing activated alumina with indigenous laterite and bauxite as potential sorbents for removing fluoride from drinking water in Ghana

USGS Publications Warehouse

Craig, Laura; Stillings, Lisa; Decker, David L.; Thomas, James M.

2015-01-01

Fluoride is considered beneficial to teeth and bones when consumed in low concentrations, but at elevated concentrations it can cause dental and skeletal fluorosis. Most fluoride-related health problems occur in poor, rural communities of the developing world where groundwater fluoride concentrations are high and the primary sources of drinking water are from community hand-pump borehole drilled wells. One solution to drinking high fluoride water is to attach a simple de-fluoridation filter to the hand-pump; and indigenous materials have been recommended as low-cost sorbents for use in these filters. In an effort to develop an effective, inexpensive, and low-maintenance de-fluoridation filter for a high fluoride region in rural northern Ghana, this study conducted batch fluoride adsorption experiments and potentiometric titrations to investigate the effectiveness of indigenous laterite and bauxite as sorbents for fluoride removal. It also determined the physical and chemical properties of each sorbent. Their properties and the experimental results, including fluoride adsorption capacity, were then compared to those of activated alumina, which has been identified as a good sorbent for removing fluoride from drinking water. The results indicate that, of the three sorbents, bauxite has the highest fluoride adsorption capacity per unit area, but is limited by a low specific surface area. When considering fluoride adsorption per unit weight, activated alumina has the highest fluoride adsorption capacity because of its high specific surface area. Activated alumina also adsorbs fluoride well in a wider pH range than bauxite, and particularly laterite. The differences in adsorption capacity are largely due to surface area, pore size, and mineralogy of the sorbent.

Addressing the Interface Issues in All-Solid-State Bulk-Type Lithium Ion Battery via an All-Composite Approach.

PubMed

Chen, Ru-Jun; Zhang, Yi-Bo; Liu, Ting; Xu, Bing-Qing; Lin, Yuan-Hua; Nan, Ce-Wen; Shen, Yang

2017-03-22

All-solid-state bulk-type lithium ion batteries (LIBs) are considered ultimate solutions to the safety issues associated with conventional LIBs using flammable liquid electrolyte. The development of bulk-type all-solid-state LIBs has been hindered by the low loading of active cathode materials, hence low specific surface capacity, and by the high interface resistance, which results in low rate and cyclic performance. In this contribution, we propose and demonstrate a synergistic all-composite approach to fabricating flexible all-solid-state LIBs. PEO-based composite cathode layers (filled with LiFePO 4 particles) of ∼300 μm in thickness and composite electrolyte layers (filled with Al-LLZTO particles) are stacked layer-by-layer with lithium foils as negative layer and hot-pressed into a monolithic all-solid-state LIB. The flexible LIB delivers a high specific discharge capacity of 155 mAh/g, which corresponds to an ultrahigh surface capacity of 10.8 mAh/cm 2 , exhibits excellent capacity retention up to at least 10 cycles and could work properly under harsh operating conditions such as bending or being sectioned into pieces. The all-composite approach is favorable for improving both mesoscopic and microscopic interfaces inside the all-solid-state LIB and may provide a new toolbox for design and fabrication of all-solid-state LIBs.

Excess Li-Ion Storage on Reconstructed Surfaces of Nanocrystals To Boost Battery Performance

DOE PAGES

Duan, Yandong; Zhang, Bingkai; Zheng, Jiaxin; ...

2017-08-03

Because of their enhanced kinetic properties, nanocrystallites have received much attention as potential electrode materials for energy storage. However, because of the large specific surface areas of nanocrystallites, they usually suffer from decreased energy density, cycling stability, and effective electrode capacity. Here, in this work, we report a size-dependent excess capacity beyond theoretical value (170 mA h g -1) by introducing extra lithium storage at the reconstructed surface in nanosized LiFePO 4 (LFP) cathode materials (186 and 207 mA h g -1 in samples with mean particle sizes of 83 and 42 nm, respectively). Moreover, this LFP composite also showsmore » excellent cycling stability and high rate performance. Our multimodal experimental characterizations and ab initio calculations reveal that the surface extra lithium storage is mainly attributed to the charge passivation of Fe by the surface C–O–Fe bonds, which can enhance binding energy for surface lithium by compensating surface Fe truncated symmetry to create two types of extra positions for Li-ion storage at the reconstructed surfaces. Such surface reconstruction nanotechnology for excess Li-ion storage makes full use of the large specific surface area of the nanocrystallites, which can maintain the fast Li-ion transport and greatly enhance the capacity. Finally, this discovery and nanotechnology can be used for the design of high-capacity and efficient lithium ion batteries.« less

Excess Li-Ion Storage on Reconstructed Surfaces of Nanocrystals To Boost Battery Performance

DOE Office of Scientific and Technical Information (OSTI.GOV)

Duan, Yandong; Zhang, Bingkai; Zheng, Jiaxin

Because of their enhanced kinetic properties, nanocrystallites have received much attention as potential electrode materials for energy storage. However, because of the large specific surface areas of nanocrystallites, they usually suffer from decreased energy density, cycling stability, and effective electrode capacity. Here, in this work, we report a size-dependent excess capacity beyond theoretical value (170 mA h g -1) by introducing extra lithium storage at the reconstructed surface in nanosized LiFePO 4 (LFP) cathode materials (186 and 207 mA h g -1 in samples with mean particle sizes of 83 and 42 nm, respectively). Moreover, this LFP composite also showsmore » excellent cycling stability and high rate performance. Our multimodal experimental characterizations and ab initio calculations reveal that the surface extra lithium storage is mainly attributed to the charge passivation of Fe by the surface C–O–Fe bonds, which can enhance binding energy for surface lithium by compensating surface Fe truncated symmetry to create two types of extra positions for Li-ion storage at the reconstructed surfaces. Such surface reconstruction nanotechnology for excess Li-ion storage makes full use of the large specific surface area of the nanocrystallites, which can maintain the fast Li-ion transport and greatly enhance the capacity. Finally, this discovery and nanotechnology can be used for the design of high-capacity and efficient lithium ion batteries.« less

Lithium ion rechargeable systems studies

NASA Astrophysics Data System (ADS)

Levy, Samuel C.; Lasasse, Robert R.; Cygan, Randall T.; Voigt, James A.

Lithium ion systems, although relatively new, have attracted much interest worldwide. Their high energy density, long cycle life and relative safety, compared with metallic lithium rechargeable systems, make them prime candidates for powering portable electronic equipment. Although lithium ion cells are presently used in a few consumer devices, e.g., portable phones, camcorders, and laptop computers, there is room for considerable improvement in their performance. Specific areas that need to be addressed include: (1) carbon anode-increase reversible capacity, and minimize passivation; (2) cathode-extend cycle life, improve rate capability, and increase capacity. There are several programs ongoing at Sandia National Laboratories which are investigating means of achieving the stated objectives in these specific areas. This paper will review these programs.

Three-dimensional graphene sheets with NiO nanobelt outgrowths for enhanced capacity and long term high rate cycling Li-ion battery anode material

NASA Astrophysics Data System (ADS)

Shi, Waipeng; Zhang, Yingmeng; Key, Julian; Shen, Pei Kang

2018-03-01

An efficient synthesis method to grow well attached NiO nanobelts from 3D graphene sheets (3DGS) is reported herein. Ni-ion exchanged resin provides the initial Ni reactant portion, which serves both as a catalyst to form 3DGS and then as a seeding agent to grow the NiO nanobelts. The macroporous structure of 3DGS provides NiO containment to achieve a high cycling stability of up to 445 mAh g-1 after 360 cycles (and >112% capacity retention after 515 cycles) at a high current density of 2 A g-1. With a 26.8 wt.% content of NiO on 3DGS, increases in specific and volumetric capacity were 41.6 and 75.7% respectively over that of 3DGS at matching current densities. Therefore, the seeded growth of NiO nanobelts from 3DGS significantly boosts volumetric capacity, while 3DGS enables high rate long term cycling of the NiO. The high rate cycling stability of NiO on 3DGS can be attributed to (i) good attachment and contact to the large surface of 3DGS, (ii) high electron conductivity and rapid Li-ion transfer (via the interconnected, highly conductive graphitized walls of 3DGS) and (iii) buffering void space in 3DGS to contain volume expansion of NiO during charge/discharge.

Community Capacity Building for Physical Activity Promotion among Older Adults—A Literature Review

PubMed Central

Ubert, Tobias; Forberger, Sarah; Gansefort, Dirk; Zeeb, Hajo; Brand, Tilman

2017-01-01

Community-based interventions to promote physical activity (PA) among older adults are of high interest in health promotion since they promise to be effective strategies to reach this population group. Community capacity building, that is, the local promotion of knowledge, skills, commitment, structures, and leadership, is among the recommended core strategies. However, little guidance is provided on how to achieve a high degree of community capacity. This study aims to identify practical strategies to enhance community capacities for PA promotion among older adults (50 years or older) and to evaluate their success. A literature review was conducted using scientific databases (PsycInfo and Web of Sciences) and grey literature (national and international project databases), and 14 studies (16 articles) were identified. Five groups of capacity building strategies emerged from the literature: (1) building community coalitions and networks, (2) training of professionals, (3) training of laypersons, (4) strengthening competence and awareness in the target population, and (5) allocation of financial resources. All studies used more than one strategy. Coalition building and strengthening competence and awareness were most frequently used. Feasibility and acceptability of the capacity building strategies were demonstrated. However, intervention effects on PA behavior and other relevant outcomes were inconsistent. The one study that systematically compared different capacity building approaches did not find any evidence for beneficial effects of intensified capacity building. More rigorous research evaluating the efficacy of specific strategies to enhance community capacities for PA promotion is needed. PMID:28902146

Community Capacity Building for Physical Activity Promotion among Older Adults-A Literature Review.

PubMed

Ubert, Tobias; Forberger, Sarah; Gansefort, Dirk; Zeeb, Hajo; Brand, Tilman

2017-09-13

Community-based interventions to promote physical activity (PA) among older adults are of high interest in health promotion since they promise to be effective strategies to reach this population group. Community capacity building, that is, the local promotion of knowledge, skills, commitment, structures, and leadership, is among the recommended core strategies. However, little guidance is provided on how to achieve a high degree of community capacity. This study aims to identify practical strategies to enhance community capacities for PA promotion among older adults (50 years or older) and to evaluate their success. A literature review was conducted using scientific databases (PsycInfo and Web of Sciences) and grey literature (national and international project databases), and 14 studies (16 articles) were identified. Five groups of capacity building strategies emerged from the literature: (1) building community coalitions and networks, (2) training of professionals, (3) training of laypersons, (4) strengthening competence and awareness in the target population, and (5) allocation of financial resources. All studies used more than one strategy. Coalition building and strengthening competence and awareness were most frequently used. Feasibility and acceptability of the capacity building strategies were demonstrated. However, intervention effects on PA behavior and other relevant outcomes were inconsistent. The one study that systematically compared different capacity building approaches did not find any evidence for beneficial effects of intensified capacity building. More rigorous research evaluating the efficacy of specific strategies to enhance community capacities for PA promotion is needed.

Carrying capacity of Peucang Island for ecotourism management in Ujung Kulon National Park

NASA Astrophysics Data System (ADS)

Wiyono, K. H.; Muntasib, E. K. S. H.; Yulianda, F.

2018-05-01

Peucang Island is one of island in Ujung Kulon National Park (UKNP), appointed as priority area and welcome area for tourism. This research aimed to calculate the carrying capacity of Peucang Island for ecotourism development (Study sites of this research are Karang Copong jungle trail and 8 sites of Peucangs beach). This research used observation method (wildlife exploration, measure the lenght of jungle track, and measure 10 parameters of beach), literature study and and interview method to collect data. The data of jungle track analyzed use Cifuentes’s formula. The result showed that Karang Copong jungle trekking had 20,000 visitors/day for Physical Carrying Capacity (PCC), 4 838 visitors/day for Real Carrying Capacity (RCC), and 6 visitors/day for Efective Carrying Capacity (ECC). Observation of biological aspect showed that there were some damages of vegetation along the track, and the changes in animal behavior. The data of beach carrying capacity analyzed use Yulianda’s formula that measured with the suitability map approach. Based on the suitability map, two beaches were classified in suitable category, while six beaches) were classified in highly suitable category for tourism activities. All of the beaches had different number of carrying capacity, specifically there are 70 visitors/day in highly suitable beach and 27 visitors/day in suitable beach. The number of visitor nowadays still not exceed from carrying capacity number of PCC, RCC of jungle trails and carrying capacity of the beach area, but the number has exceeded from the ECC numbers.

Region-specific differences in bioenergetic proteins and protein response to acute high fat diet in brains of low and high capacity runner rats.

PubMed

Gan, Li; Ma, Delin; Li, Min; Yang, Fu-Chen; Rogers, Robert S; Wheatley, Joshua L; Koch, Lauren G; Britton, Steven L; Thyfault, John P; Geiger, Paige C; Stanford, John A

2018-05-01

Aerobic capacity is a strong predictor of mortality. Low capacity runner (LCR) rats exhibit reduced mitochondrial function in peripheral organs. A high fat diet (HFD) can worsen metabolic phenotype in LCR rats. Little is known about metabolic changes in the brains of these rats, however. This study examined protein markers of mitochondrial function and metabolism as a function of aerobic running capacity and an acute HFD in four brain regions: the striatum, hippocampus, hypothalamus, and substantia nigra. After 3 days HFD or chow diets, we measured peroxisome proliferator-activated receptor-γ coactivator 1α (PGC1-α), nuclear respiratory factors 1 (Nrf-1), mitochondrial transcription factor A (TFAM), and phosphorylated (activated) AMP-activated protein kinase (p-AMPK) protein levels in the four brain regions. LCR rats exhibited lower levels of mitochondrial proteins (PGC1-α, Nrf-1, TFAM), and greater p-AMPK, in striatum, but not in the other brain regions. Mitochondrial protein levels were greater in HFD LCR striatum, while p-AMPK was lower in this group. Markers of lower mitochondrial biogenesis and increased metabolic demand were limited to the LCR striatum, which nevertheless maintained the capacity to respond to an acute HFD challenge. Copyright © 2018 Elsevier B.V. All rights reserved.

Structural, thermal and optical properties of KTi(0.92)La(0.08)OPO4 and KTi(0.94)Nd(0.06)OPO4.

PubMed

Sadhasivam, S; Perumal, Rajesh Narayana; Ramasamy, P

2015-10-05

KTi0.92La0.08OPO4 (KTP:La) and KTi0.94Nd0.06OPO4 (KTP:Nd) single crystals are grown using high temperature top seeded flux growth technique. The strain derived from doping is calculated from Williamson-Hall relation. The packing structure and lattice parameter of the grown crystals are analyzed using single crystal X-ray diffraction. The bonding, distortion and change in inter-atomic distances by strain effects of doping are assessed by Raman spectroscopy. Thermal stabilities of grown crystals are evaluated by specific heat capacity measurement. Pronounced high specific heat capacity is recorded as 1.16 J/gK at 498 K for KTP:Nd. Second harmonic generation intensities are measured for KTP:Nd and KTP:La single crystal. Copyright © 2015 Elsevier B.V. All rights reserved.

From Metal-Organic Framework to Porous Carbon Polyhedron: Toward Highly Reversible Lithium Storage.

PubMed

Peng, Hai-Jun; Hao, Gui-Xia; Chu, Zhao-Hua; Cui, Ying-Lin; Lin, Xiao-Ming; Cai, Yue-Peng

2017-08-21

By application of a newly designed T-shaped ligand 5-(4-pyridin-4-yl-benzoylamino)isophthalic acid (H 2 PBAI) to assemble with Zn(II) ions under solvothermal conditions, a novel porous polyhedral metal-organic framework (Zn-PBAI) with pcu topology has been obtained. When treated as a precursor by annealing of Zn-PBAI at various temperatures, porous carbon polyhedra (PCP) were prepared and tested as an anode material for lithium-ion batteries. The results show that PCP carbonized at 1000 °C (PCP-1000) manifest the highest reversible specific capacity of about 1125 mAh g -1 at a current of 500 mA g -1 after 200 cycles, which is supposed to benefit from the large accessible specific area and high electric conductivity. Moreover, PCP-1000 electrode materials also exhibit superior cyclic stability and good rate capacity.

High-temperature heat capacity of CdO-V2O5 oxides

NASA Astrophysics Data System (ADS)

Denisova, L. T.; Chumilina, L. G.; Belousova, N. V.; Denisov, V. M.; Galiakhmetova, N. A.

2017-12-01

Vanadates Cd2V2O7 and CdV2O6 have been prepared from CdO i V2O5 by three-phase synthesis with subsequent burning at 823-1073 K and 823-853 K, respectively. The molar heat capacity of these oxide compounds has been measured by differential scanning calorimetry. The enthalpy change, the entropy change, and the reduced Gibbs energy are calculated using the experimental dependences C p = f( T). It is shown that there is a correlation between the specific heat capacity and the composition of CdO-V2O5 oxide system.

Self-reflection and set-shifting mediate awareness in cognitively preserved schizophrenia patients.

PubMed

Gilleen, James; David, Anthony; Greenwood, Kathryn

2016-05-01

Poor insight in schizophrenia has been linked to poor cognitive functioning, psychological processes such as denial, or more recently with impaired metacognitive capacity. Few studies, however, have investigated the potential co-dependency of multiple factors in determining level of insight, but such a model is necessary in order to account for patients with good cognitive functioning who have very poor awareness. As evidence suggests that set-shifting and cognitive insight (self-reflection (SR) and self-certainty) are strong predictors of awareness we proposed that these factors are key mediators in the relationship between cognition and awareness. We hypothesised that deficits specifically in SR and set-shifting determine level of awareness in the context of good cognition. Thirty schizophrenia patients were stratified by high and low awareness of illness and executive functioning scores. Cognitive insight, cognition, mood and symptom measures were compared between sub-groups. A low insight/high executive functioning (LI-HE) group, a high insight/high executive functioning (HI-HE) group and a low insight/low executive functioning (LI-LE) group were revealed. As anticipated, the LI-HE patients showed significantly lower capacity for SR and set-shifting than the HI-HE patients. This study indicates that good cognitive functioning is necessary but not sufficient for good awareness; good awareness specifically demands preserved capacity to self-reflect and shift-set. Results support Nelson and Narens' [1990. Metamemory: A theoretical framework and new findings. The Psychology of Learning and Motivation, 26, 125-173] model of metacognition by which awareness is founded on control (set-shifting) and monitoring (SR) processes. These specific factors could be targeted to improve insight in patients with otherwise unimpaired cognitive function.

Supercapacitors based on high-quality graphene scrolls.

PubMed

Zeng, Fanyan; Kuang, Yafei; Liu, Gaoqin; Liu, Rui; Huang, Zhongyuan; Fu, Chaopeng; Zhou, Haihui

2012-07-07

High-quality graphene scrolls (GSS) with a unique scrolled topography are designed using a microexplosion method. Their capacitance properties are investigated by cyclic voltammetry, galvanostatic charge-discharge and electrical impedance spectroscopy. Compared with the specific capacity of 110 F g(-1) for graphene sheets, a remarkable capacity of 162.2 F g(-1) is obtained at the current density of 1.0 A g(-1) in 6 M KOH aqueous solution owing to the unique scrolled structure of GSS. The capacity value is increased by about 50% only because of the topological change of graphene sheets. Meanwhile, GSS exhibit excellent long-term cycling stability along with 96.8% retained after 1000 cycles at 1.0 A g(-1). These encouraging results indicate that GSS based on the topological structure of graphene sheets are a kind of promising material for supercapacitors.

Supercapacitors based on high-quality graphene scrolls

NASA Astrophysics Data System (ADS)

Zeng, Fanyan; Kuang, Yafei; Liu, Gaoqin; Liu, Rui; Huang, Zhongyuan; Fu, Chaopeng; Zhou, Haihui

2012-06-01

High-quality graphene scrolls (GSS) with a unique scrolled topography are designed using a microexplosion method. Their capacitance properties are investigated by cyclic voltammetry, galvanostatic charge-discharge and electrical impedance spectroscopy. Compared with the specific capacity of 110 F g-1 for graphene sheets, a remarkable capacity of 162.2 F g-1 is obtained at the current density of 1.0 A g-1 in 6 M KOH aqueous solution owing to the unique scrolled structure of GSS. The capacity value is increased by about 50% only because of the topological change of graphene sheets. Meanwhile, GSS exhibit excellent long-term cycling stability along with 96.8% retained after 1000 cycles at 1.0 A g-1. These encouraging results indicate that GSS based on the topological structure of graphene sheets are a kind of promising material for supercapacitors.

Heat capacity of high-purity lanthanum

DOE Office of Scientific and Technical Information (OSTI.GOV)

Pan, P.H.; Finnemore, D.K.; Bevolo, A.J.

1980-04-01

A study of the specific heat of high-purity single-phase dhcp La shows that this material is an intrinsic type-II superconductor with a kappa of about 2.4. The temperature dependence of the free energy is characteristic of an intermediate coupling superconductor with 2..delta../k/sub B/T/sub c/ approx. = 3.7.

Factors affecting the response to exercise in patients with severe pulmonary arterial hypertension.

PubMed

Flox-Camacho, Angela; Escribano-Subías, Pilar; Jiménez-López Guarch, Carmen; Fernández-Vaquero, Almudena; Martín-Ríos, Dolores; de la Calzada-Campo, Carlos Sáenz

2011-01-01

Ergospirometry objectively quantifies exercise capacity. Up until now, the response to exercise evaluated by ergospirometry in patients with pulmonary arterial hypertension has only been described in recently diagnosed.patients. Our aim is to describe the response to exercise in patients with severe pulmonary arterial hypertension under specific treatment and define which parameters determine their exercise capacity. A cross-sectional study was performed on 80 patients, 57 women, aged 45 (14), with severe pulmonary arterial hypertension (48 idiopathic, 14 related to toxic rapeseed oil, 13 to connective tissue disease, 5 to human immunodeficiency virus), mean pulmonary pressure at diagnosis 61(15)mmHg and after 49(33) months under treatment since diagnosis. Biomarkers were measured and echocardiography and ergospirometry were performed the same day. Our patients, under specific treatment, showed the typical behaviour of patients with pulmonary arterial hypertension with less limitation of both aerobic capacity and ventilatory efficiency. Being male (p=0.004), high ventilatory equivalent for carbon dioxide at anaerobic threshold (p<0.001) or biomarkers (p=0.006) were the strongest predictors of impaired peak oxygen uptake in multivariate analysis, whereas for an impaired percentage achieved of predicted value were right ventricle diastolic diameter (p<0.001), months of treatment (p=0.01) and high ventilatory equivalent for CO(2) (p<0.001). In pulmonary arterial hypertension, right ventricle dysfunction (expressed by its dilation or high NTproBNP) and impaired ventilatory inefficiency as well as being male or a short time under treatment can be considered as determining factors of impaired exercise capacity. Copyright © 2010 SEPAR. Published by Elsevier Espana. All rights reserved.

L-lactic acid and sodium p-toluenesulfonate co-doped polypyrrole for high performance cathode in sodium ion battery

NASA Astrophysics Data System (ADS)

Liao, Qishu; Hou, Hongying; Liu, Xianxi; Yao, Yuan; Dai, Zhipeng; Yu, Chengyi; Li, Dongdong

2018-04-01

In this work, polypyrrole (PPy) was co-doped with L-lactic acid (LA) and sodium p-toluenesulfonate (TsONa) for high performance cathode in sodium ion battery (SIB) via facile one-step electropolymerization on Fe foil. The as-synthesized LA/TsONa co-doped PPy cathode was investigated in terms of scanning electron microscope (SEM), Fourier transform infrared spectroscopy (FTIR), galvanostatic charge/discharge and cyclic voltammetry (CV). The results suggested that some oval-bud-like LA/TsONa co-doped PPy particles did form and tightly combine with the surface of Fe foil; furthermore, LA/TsONa co-doped PPy cathode also delivered higher electrochemical performances than TsONa mono-doped PPy cathode. For example, the initial specific discharge capacity was as high as about 124 mAh/g, and the reversible specific capacity still maintained at about 110 mAh/g even after 50 cycles, higher than those of TsONa mono-doped PPy cathode. The synergy effect of multi components of LA/TsONa co-doped PPy cathode should be responsible for high electrochemical performances.

Size dependent polaronic conduction in hematite

DOE Office of Scientific and Technical Information (OSTI.GOV)

Sharma, Monika; Banday, Azeem; Murugavel, Sevi

2016-05-23

Lithium Ion Batteries have been attracted as the major renewable energy source for all portable electronic devices because of its advantages like superior energy density, high theoretical capacity, high specific energy, stable cycling and less memory effects. Recently, α-Fe{sub 2}O{sub 3} has been considered as a potential anode material due to high specific capacity, low cost, high abundance and environmental benignity. We have synthesized α-Fe{sub 2}O{sub 3} with various sizes by using the ball milling and sol-gel procedure. Here, we report the dc conductivity measurement for the crystallite size ranging from 15 nm to 50 nm. It has been observedmore » that the enhancement in the polaronic conductivity nearly two orders in magnitude while reducing the crystallite size from bulk into nano scale level. The enhancement in the conductivity is due to the augmented to compressive strain developed in the material which leads to pronounced decrease in the hopping length of polarons. Thus, nanocrystaline α-Fe{sub 2}O{sub 3} may be a better alternative anode material for lithium ion batteries than earlier reported systems.« less

A short protocol using dexamethasone and monophosphoryl lipid A generates tolerogenic dendritic cells that display a potent migratory capacity to lymphoid chemokines

PubMed Central

2013-01-01

Background Generation of tolerogenic dendritic cells (TolDCs) for therapy is challenging due to its implications for the design of protocols suitable for clinical applications, which means not only using safe products, but also working at defining specific biomarkers for TolDCs identification, developing shorter DCs differentiation methods and obtaining TolDCs with a stable phenotype. We describe here, a short-term protocol for TolDCs generation, which are characterized in terms of phenotypic markers, cytokines secretion profile, CD4+ T cell-stimulatory ability and migratory capacity. Methods TolDCs from healthy donors were generated by modulation with dexamethasone plus monophosphoryl lipid A (MPLA-tDCs). We performed an analysis of MPLA-tDCs in terms of yield, viability, morphology, phenotypic markers, cytokines secretion profile, stability, allogeneic and antigen-specific CD4+ T-cell stimulatory ability and migration capacity. Results After a 5-day culture, MPLA-tDCs displayed reduced expression of costimulatory and maturation molecules together to an anti-inflammatory cytokines secretion profile, being able to maintain these tolerogenic features even after the engagement of CD40 by its cognate ligand. In addition, MPLA-tDCs exhibited reduced capabilities to stimulate allogeneic and antigen-specific CD4+ T cell proliferation, and induced an anti-inflammatory cytokine secretion pattern. Among potential tolerogenic markers studied, only TLR-2 was highly expressed in MPLA-tDCs when compared to mature and immature DCs. Remarkable, like mature DCs, MPLA-tDCs displayed a high CCR7 and CXCR4 expression, both chemokine receptors involved in migration to secondary lymphoid organs, and even more, in an in vitro assay they exhibited a high migration response towards CCL19 and CXCL12. Conclusion We describe a short-term protocol for TolDC generation, which confers them a stable phenotype and migratory capacity to lymphoid chemokines, essential features for TolDCs to be used as therapeutics for autoimmunity and prevention of graft rejection. PMID:23706017

Reinstating lead for high-loaded efficient negative electrode for rechargeable sodium-ion battery

NASA Astrophysics Data System (ADS)

Darwiche, Ali; Dugas, Romain; Fraisse, Bernard; Monconduit, Laure

2016-02-01

Due to its weight and toxicity, Pb is usually not considered as possible anode for Li- and Na-ion (NIBs) batteries. Nevertheless the toxicity is related to specific applications and its recycling is more than 99% which is one of the highest recycling rates on the planet where no other power source is utilized in more applications with such sustainability. For this reason, we have investigated micrometric lead particles as electrode for NIBs in an ether-based electrolyte (1 M NaPF6 in diglyme). The cyclability, coulombic efficiency and rate capability of lead were unexpected. A high loaded lead electrode with 98%wt of Pb and only 1% of carbon additive showed i) a capacity retention of 464 mA h/g after 50 cycles with only 1.5% of capacity loss, which represents a high volumetric capacity of 5289 mA h/cm3 due to the high density of Pb and ii) a very interesting capacity retention even at high current rate (1950 mA/g). In situ XRD study confirmed a sodiation-desodiation process in four steps. Preliminary tests in Pb//Na3V2(PO4)2F3 full cells showed promising results demonstrating that Pb could be a practical candidate for future high energy density Na-ion batteries with an efficient sodiated or non sodiated positive electrode.

Comparison of scavenging capacities of vegetables by ORAC and EPR.

PubMed

Kameya, Hiromi; Watanabe, Jun; Takano-Ishikawa, Yuko; Todoriki, Setsuko

2014-02-15

Reactive oxygen species (ROS) are considered to be causative agents of many health problems. In spite of this, the radical-specific scavenging capacities of food samples have not been well studied. In the present work, we have developed an electron paramagnetic resonance (EPR) spin trapping method for analysis of the scavenging capacities of food samples for multiple ROS, utilising the same photolysis procedure for generating each type of radical. The optimal conditions for effective evaluation of hydroxyl, superoxide, and alkoxyl radical scavenging capacity were determined. Quantification of radical adducts was found to be highly reproducible, with variations of less than 4%. The optimised EPR spin trapping method was used to analyse the scavenging capacities of 54 different vegetable extracts for multiple radicals, and the results were compared with oxygen radical absorption capacity values. Good correlations between the two methods were observed for superoxide and alkoxyl radicals, but not for hydroxyl. Copyright © 2013 Elsevier Ltd. All rights reserved.

Simultaneous Measurements of Auto-Immune and Infectious Disease Specific Antibodies Using a High Throughput Multiplexing Tool

PubMed Central

Asati, Atul; Kachurina, Olga; Kachurin, Anatoly

2012-01-01

Considering importance of ganglioside antibodies as biomarkers in various immune-mediated neuropathies and neurological disorders, we developed a high throughput multiplexing tool for the assessment of gangliosides-specific antibodies based on Biolpex/Luminex platform. In this report, we demonstrate that the ganglioside high throughput multiplexing tool is robust, highly specific and demonstrating ∼100-fold higher concentration sensitivity for IgG detection than ELISA. In addition to the ganglioside-coated array, the high throughput multiplexing tool contains beads coated with influenza hemagglutinins derived from H1N1 A/Brisbane/59/07 and H1N1 A/California/07/09 strains. Influenza beads provided an added advantage of simultaneous detection of ganglioside- and influenza-specific antibodies, a capacity important for the assay of both infectious antigen-specific and autoimmune antibodies following vaccination or disease. Taken together, these results support the potential adoption of the ganglioside high throughput multiplexing tool for measuring ganglioside antibodies in various neuropathic and neurological disorders. PMID:22952605

N/S Co-Doped 3 D Porous Carbon Nanosheet Networks Enhancing Anode Performance of Sodium-Ion Batteries.

PubMed

Zou, Lei; Lai, Yanqing; Hu, Hongxing; Wang, Mengran; Zhang, Kai; Zhang, Peng; Fang, Jing; Li, Jie

2017-10-12

A facile and scalable method is realized for the in situ synthesis of N/S co-doped 3 D porous carbon nanosheet networks (NSPCNNs) as anode materials for sodium-ion batteries. During the synthesis, NaCl is used as a template to prepare porous carbon nanosheet networks. In the resultant architecture, the unique 3 D porous architecture ensures a large specific surface area and fast diffusion paths of both electrons and ions. In addition, the import of N/S produces abundant defects, increased interlayer spacings, more active sites, and high electronic conductivity. The obtained products deliver a high specific capacity and excellent long-term cycling performance, specifically, a capacity of 336.2 mA h g -1 at 0.05 A g -1 , remaining as large as 214.9 mA h g -1 after 2000 charge/discharge cycles at 0.5 A g -1 . This material has great prospects for future applications of scalable, low-cost, and environmentally friendly sodium-ion batteries. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reversible Intercalation of Fluoride-Anion Receptor Complexes in Graphite

NASA Technical Reports Server (NTRS)

West, William C.; Whitacre, Jay F.; Leifer, Nicole; Greenbaum, Steve; Smart, Marshall; Bugga, Ratnakumar; Blanco, Mario; Narayanan, S. R.

2007-01-01

We have demonstrated a route to reversibly intercalate fluoride-anion receptor complexes in graphite via a nonaqueous electrochemical process. This approach may find application for a rechargeable lithium-fluoride dual-ion intercalating battery with high specific energy. The cell chemistry presented here uses graphite cathodes with LiF dissolved in a nonaqueous solvent through the aid of anion receptors. Cells have been demonstrated with reversible cathode specific capacity of approximately 80 mAh/g at discharge plateaus of upward of 4.8 V, with graphite staging of the intercalant observed via in situ synchrotron X-ray diffraction during charging. Electrochemical impedance spectroscopy and B-11 nuclear magnetic resonance studies suggest that cointercalation of the anion receptor with the fluoride occurs during charging, which likely limits the cathode specific capacity. The anion receptor type dictates the extent of graphite fluorination, and must be further optimized to realize high theoretical fluorination levels. To find these optimal anion receptors, we have designed an ab initio calculations-based scheme aimed at identifying receptors with favorable fluoride binding and release properties.

Financial and testamentary capacity evaluations: procedures and assessment instruments underneath a functional approach.

PubMed

Sousa, Liliana B; Simões, Mário R; Firmino, Horácio; Peisah, Carmelle

2014-02-01

Mental health professionals are frequently involved in mental capacity determinations. However, there is a lack of specific measures and well-defined procedures for these evaluations. The main purpose of this paper is to provide a review of financial and testamentary capacity evaluation procedures, including not only the traditional neuropsychological and functional assessment but also the more recently developed forensic assessment instruments (FAIs), which have been developed to provide a specialized answer to legal systems regarding civil competencies. Here the main guidelines, papers, and other references are reviewed in order to achieve a complete and comprehensive selection of instruments used in the assessment of financial and testamentary capacity. Although some specific measures for financial abilities have been developed recently, the same is not true for testamentary capacity. Here are presented several instruments or methodologies for assessing financial and testamentary capacity, including neuropsychological assessment, functional assessment scales, performance based functional assessment instruments, and specific FAIs. FAIs are the only specific instruments intended to provide a specific and direct answer to the assessment of financial capacity based on legal systems. Considering the need to move from a diagnostic to a functional approach in financial and testamentary capacity evaluations, it is essential to consider both general functional examination as well as cognitive functioning.

Germanium microflower-on-nanostem as a high-performance lithium ion battery electrode

PubMed Central

Lee, Gwang-Hee; Kwon, S. Joon; Park, Kyung-Soo; Kang, Jin-Gu; Park, Jae-Gwan; Lee, Sungjun; Kim, Jae-Chan; Shim, Hyun-Woo; Kim, Dong-Wan

2014-01-01

We demonstrate a new design of Ge-based electrodes comprising three-dimensional (3-D) spherical microflowers containing crystalline nanorod networks on sturdy 1-D nanostems directly grown on a metallic current collector by facile thermal evaporation. The Ge nanorod networks were observed to self-replicate their tetrahedron structures and form a diamond cubic lattice-like inner network. After etching and subsequent carbon coating, the treated Ge nanostructures provide good electrical conductivity and are resistant to gradual deterioration, resulting in superior electrochemical performance as anode materials for LIBs, with a charge capacity retention of 96% after 100 cycles and a high specific capacity of 1360 mA h g−1 at 1 C and a high-rate capability with reversible capacities of 1080 and 850 mA h g−1 at the rates of 5 and 10 C, respectively. The improved electrochemical performance can be attributed to the fast electron transport and good strain accommodation of the carbon-filled Ge microflower-on-nanostem hybrid electrode. PMID:25363317

Discharging a Li-S battery with ultra-high sulphur content cathode using a redox mediator.

PubMed

Kim, Kwi Ryong; Lee, Kug-Seung; Ahn, Chi-Yeong; Yu, Seung-Ho; Sung, Yung-Eun

2016-08-30

Lithium-sulphur batteries are under intense research due to the high specific capacity and low cost. However, several problems limit their commercialization. One of them is the insulating nature of sulphur, which necessitates a large amount of conductive agent and binder in the cathode, reducing the effective sulphur load as well as the energy density. Here we introduce a redox mediator, cobaltocene, which acts as an electron transfer agent between the conductive surface and the polysulphides in the electrolyte. We confirmed that cobaltocene could effectively convert polysulphides to Li2S using scanning electron microscope, X-ray absorption near-edge structure and in-situ X-ray diffraction studies. This redox mediator enabled excellent electrochemical performance in a cathode with ultra-high sulphur content (80 wt%). It delivered 400 mAh g(-1)cathode capacity after 50 cycles, which is equivalent to 800 mAh g(-1)S in a typical cathode with 50 wt% sulphur. Furthermore, the volumetric capacity was also dramatically improved.

Polyaniline nanowire arrays aligned on nitrogen-doped carbon fabric for high-performance flexible supercapacitors.

PubMed

Yu, Pingping; Li, Yingzhi; Yu, Xinyi; Zhao, Xin; Wu, Lihao; Zhang, Qinghua

2013-09-24

A combination of vertical polyaniline (PANI) nanowire arrays and nitrogen plasma etched carbon fiber cloths (eCFC) was fabricated to create 3D nanostructured PANI/eCFC composites. The small size of the highly ordered PANI nanowires can greatly reduce the scale of the diffusion length, allowing for the improved utilization of electrode materials. A two-electrode flexible supercapacitor based on PANI/eCFC demonstrates a high specific capacitance (1035 F g(-1) at a current density of 1 A g(-1)), good rate capability (88% capacity retention at 8 A g(-1)), and long-term cycle life (10% capacity loss after 5000 cycles). The lightweight, low-cost, flexible composites are promising candidates for use in energy storage device applications.

In situ formed Si nanoparticle network with micron-sized Si particles for lithium-ion battery anodes.

PubMed

Wu, Mingyan; Sabisch, Julian E C; Song, Xiangyun; Minor, Andrew M; Battaglia, Vincent S; Liu, Gao

2013-01-01

To address the significant challenges associated with large volume change of micrometer-sized Si particles as high-capacity anode materials for lithium-ion batteries, we demonstrated a simple but effective strategy: using Si nanoparticles as a structural and conductive additive, with micrometer-sized Si as the main lithium-ion storage material. The Si nanoparticles connected into the network structure in situ during the charge process, to provide electronic connectivity and structure stability for the electrode. The resulting electrode showed a high specific capacity of 2500 mAh/g after 30 cycles with high initial Coulombic efficiency (73%) and good rate performance during electrochemical lithiation and delithiation: between 0.01 and 1 V vs Li/Li(+).

Mapping Structure-Composition-Property Relationships in V- and Fe-Doped LiMnPO4 Cathodes for Lithium-Ion Batteries.

PubMed

Johnson, Ian D; Loveridge, Melanie; Bhagat, Rohit; Darr, Jawwad A

2016-11-14

A series of LiMn 1-x-y Fe x V y PO 4 (LMFVP) nanomaterials have been synthesized using a pilot-scale continuous hydrothermal synthesis process (CHFS) and evaluated as high voltage cathodes in Li-ion batteries at a production rate of 0.25 kg h -1 . The rapid synthesis and screening approach has allowed the specific capacity of the high Mn content olivines to be optimized, particularly at high discharge rates. Consistent and gradual changes in the structure and performance are observed across the compositional region under investigation; the doping of Fe at 20 at% (with respect to Mn) into lithium manganese phosphate, rather than V or indeed codoping of Fe and V, gives the best balance of high capacity and high rate performance.

Flexible Carbon Nanotube Modified Separator for High-Performance Lithium-Sulfur Batteries

PubMed Central

Liu, Bin; Wu, Xiaomeng; Wang, Shan; Tang, Zhen; Yang, Quanling; Hu, Guo-Hua; Xiong, Chuanxi

2017-01-01

Lithium-sulfur (Li-S) batteries have become promising candidates for electrical energy storage systems due to their high theoretical specific energy density, low cost and environmental friendliness. However, there are some technical obstacles of lithium-sulfur batteries to be addressed, such as the shuttle effect of polysulfides. Here, we introduced organically modified carbon nanotubes (CNTs) as a coating layer for the separator to optimize structure and enhance the performance of the Li-S battery. The results showed that the cell with a CNTs-coated separator exhibited an excellent cycling performance. Compared to the blank separator, the initial discharge capacity and the capacity after 100 cycles for the CNTs-coated separator was increased by 115% and 161%, respectively. Besides, according to the rate capability test cycling from 0.1C to 2C, the battery with a CNTs-coated separator still released a capacity amounting to 90.2% of the initial capacity, when the current density returned back to 0.1C. It is believed that the organically modified CNTs coating effectively suppresses the shuttle effect during the cycling. The employment of a CNTs-coated separator provides a promising approach for high-performance lithium-sulfur batteries. PMID:28933721

Age and natural metabolically-intensive behavior affect oxidative stress and antioxidant mechanisms.

PubMed

Williams, Jason B; Roberts, Stephen P; Elekonich, Michelle M

2008-06-01

Flying honey bees have among the highest mass-specific metabolic rates ever measured, suggesting that their flight muscles may experience high levels of oxidative stress during normal daily activities. We measured parameters of oxidative stress and antioxidant capacity in highly metabolic flight muscle and less active head tissue in cohorts of age-matched nurse bees, which rarely fly, and foragers, which fly several hours per a day. Naturally occurring foraging flight elicited an increase in flight muscle Hsp70 content in both young and old foragers; however catalase and total antioxidant capacity increased only in young flight muscle. Surprisingly, young nurse bees also showed a modest daily increase in Hsp70, catalase levels and antioxidant capacity, and these effects were likely due to collecting the young nurses soon after orientation flights. There were no differences in flight muscle carbonyl content over the course of daily activity and few differences in Hsp70, catalase, total antioxidant capacity and protein carbonyl levels in head tissue regardless of age or activity. In summary, honey bee flight likely produces high levels of reactive oxygen species in flight muscle that, when coupled with age-related decreases in antioxidant activity may be responsible for behavioral senescence and reduced longevity.

MoTe2, A novel anode material for sodium ion battery

NASA Astrophysics Data System (ADS)

Panda, Manas Ranjan; Anish Raj, K.; Bao, Qiaoliang; Mitra, Sagar

2018-04-01

2D layered transition metal dichalcogenides are considered as a potential anode for sodium-ion batteries due to their high specific capacity, structural stability and its well-developed two-dimensional layers. 2D layered structure Molybdenum ditelluride (MoTe2) provides a superior Na-ion storage properties in sodium ion battery due to its comparative more interlayer spacing (0.699 nm). In the current study MoTe2 polycrystalline powder sample has been prepared by solid state reaction process, the structural and morphological studies have been carried out by XRD, FE-SEM and EDS etc. XRD study revealsthe well crystalline structure of the material having hexagonal structure. FE-SEM and EDS studies depict the uniformflakes like structure of the material. When it is tested as sodium-ion battery anode by applying a potential window 0.1-2.5 V, the material demonstrates a high capacity and high power performances. The as prepared MoTe2 shows an initial discharge capacity of 376 mA h g-1 and a corresponding discharge capacity of 303 mA h g-1 after the 50th cycle at a current density of 500 mA g-1.

Changes in mRNA levels for brain-derived neurotrophic factor after wheel running in rats selectively bred for high- and low-aerobic capacity

PubMed Central

Groves-Chapman, Jessica L.; Murray, Patrick S.; Stevens, Kristin L.; Monroe, Derek; Koch, Lauren G.; Britton, Steven L.; Holmes, Philip V.

2012-01-01

We evaluated levels of exercise-induced brain-derived neurotrophic factor (BDNF) messenger RNA (mRNA) within the hippocampal formation in rats selectively bred for 1) high intrinsic (i.e., untrained) aerobic capacity (High Capacity Runners, HCR), 2) low intrinsic aerobic capacity (Low Capacity Runners, LCR), and 3) unselected Sprague-Dawley (SD) rats with or without free access to running wheels for three weeks. The specific aim of the study was to determine whether a dose-response relationship exists between cumulative running distance and levels of BDNF mRNA. No additional treatments or behavioral manipulations were used. HCR, LCR, and SD rats were grouped by strain and randomly assigned to sedentary or activity (voluntary access to activity wheel) conditions. Animals were killed after 21 days of exposure to the assigned conditions. Daily running distances (mean ± standard deviation meters/d) during week three were: HCR (4726 ± 3220), SD (2293 ± 3461), LCR (672 ± 323). Regardless of strain, levels of BDNF mRNA in CA1 were elevated in wheel runners compared to sedentary rats and this difference persisted after adjustment for age (p=0.040). BDNF mRNA was not affected by intrinsic aerobic capacity and was not related to total running distance. The results support that BDNF mRNA expression is increased by unlimited access to activity wheel running for 3 weeks but is not dependent upon accumulated running distance. PMID:22024546

Demonstration of a high-capacity turboalternator for a 20 K, 20 W space-borne Brayton cryocooler

NASA Astrophysics Data System (ADS)

Zagarola, M.; Cragin, K.; Deserranno, D.

2014-01-01

NASA is considering multiple missions involving long-term cryogenic propellant storage in space. Liquid hydrogen and oxygen are the typical cryogens as they provide the highest specific impulse of practical chemical propellants. Storage temperatures are nominally 20 K for liquid hydrogen and 90 K for liquid oxygen. Heat loads greater than 10 W at 20 K are predicted for hydrogen storage. Current space cryocoolers have been developed for sensor cooling with refrigeration capacities less than 1 W at 20 K. In 2011, Creare Inc. demonstrated an ultra-low-capacity turboalternator for use in a turbo-Brayton cryocooler. The turboalternator produced up to 5 W of turbine refrigeration at 20 K; equivalent to approximately 3 W of net cryocooler refrigeration. This turboalternator obtained unprecedented operating speeds and efficiencies at low temperatures benefitting from new rotor design and fabrication techniques, and new bearing fabrication techniques. More recently, Creare applied these design and fabrication techniques to a larger and higher capacity 20 K turboalternator. The turboalternator was tested in a high-capacity, low temperature test facility at Creare and demonstrated up to 42 W of turbine refrigeration at 20 K; equivalent to approximately 30 W of net cryocooler refrigeration. The net turbine efficiency was the highest achieved to date at Creare for a space-borne turboalternator. This demonstration was the first step in the development of a high-capacity turbo-Brayton cryocooler for liquid hydrogen storage. In this paper, we will review the design, development and testing of the turboalternator.

Surface Modification of the LiFePO4 Cathode for the Aqueous Rechargeable Lithium Ion Battery.

PubMed

Tron, Artur; Jo, Yong Nam; Oh, Si Hyoung; Park, Yeong Don; Mun, Junyoung

2017-04-12

The LiFePO 4 surface is coated with AlF 3 via a simple chemical precipitation for aqueous rechargeable lithium ion batteries (ARLBs). During electrochemical cycling, the unfavorable side reactions between LiFePO 4 and the aqueous electrolyte (1 M Li 2 SO 4 in water) leave a highly resistant passivation film, which causes a deterioration in the electrochemical performance. The coated LiFePO 4 by 1 wt % AlF 3 has a high discharge capacity of 132 mAh g -1 and a highly improved cycle life, which shows 93% capacity retention even after 100 cycles, whereas the pristine LiFePO 4 has a specific capacity of 123 mAh g -1 and a poor capacity retention of 82%. The surface analysis results, which include X-ray photoelectron spectroscopy and transmission electron microscopy results, show that the AlF 3 coating material is highly effective for reducing the detrimental surface passivation by relieving the electrochemical side reactions of the fragile aqueous electrolyte. The AlF 3 coating material has good compatibility with the LiFePO 4 cathode material, which mitigates the surface diffusion obstacles, reduces the charge-transfer resistances and improves the electrochemical performance and surface stability of the LiFePO 4 material in aqueous electrolyte solutions.

Three-dimensional TiO2 nanowire@NiMoO4 ultrathin nanosheet core-shell arrays for lithium ion batteries

NASA Astrophysics Data System (ADS)

Cao, Minglei; Bu, Yi; Lv, Xiaowei; Jiang, Xingxing; Wang, Lichuan; Dai, Sirui; Wang, Mingkui; Shen, Yan

2018-03-01

This study reports a general and rational two-step hydrothermal strategy to fabricate three-dimensional (3D) TiO2 nanowire@NiMoO4 ultrathin nanosheet core-shell arrays (TNAs-NMO) as additives-free anodes for lithium-ion batteries (LIBs). The TNAs-NMO electrode delivers a reversible capacity of up to 446.6 mA h g-1 over 120 cycles at the current density of 0.2 A g-1 and a high rate capacity of 234.2 mA h g-1 at 2.0 A g-1. Impressively, the capacity retention efficiency is 74.7% after 2500 cycles at the high rate of 2.0 A g-1. In addition, the full cell consisting of TNAs-NMO anode and LCO cathode can afford a specific energy of up to 220.3 W h kg-1 (based on the entire mass of both electrodes). The high electrochemical performance of the TNAs-NMO electrode is ascribed to its 3D core-shell nanowire array architecture, in which the TiO2 nanowire arrays (TNAs) and the ultrathin NiMoO4 nanosheets exhibit strong synergistic effects. The TNAs maintain mechanical integrity of the electrode and the ultrathin NiMoO4 nanosheets contribute to high capacity and favorable electronic conductivity.

Melt-Spun Fe-Sb Intermetallic Alloy Anode for Performance Enhanced Sodium-Ion Batteries.

PubMed

Edison, Eldho; Sreejith, Sivaramapanicker; Madhavi, Srinivasan

2017-11-15

Owing to the high theoretical sodiation capacities, intermetallic alloy anodes have attracted considerable interest as electrodes for next-generation sodium-ion batteries (SIBs). Here, we demonstrate the fabrication of intermetallic Fe-Sb alloy anode for SIBs via a high-throughput and industrially viable melt-spinning process. The earth-abundant and low-cost Fe-Sb-based alloy anode exhibits excellent cycling stability with nearly 466 mAh g -1 sodiation capacity at a specific current of 50 mA g -1 with 95% capacity retention after 80 cycles. Moreover, the alloy anode displayed outstanding rate performance with ∼300 mAh g -1 sodiation capacity at 1 A g -1 . The crystalline features of the melt-spun fibers aid in the exceptional electrochemical performance of the alloy anode. Further, the feasibility of the alloy anode for real-life applications was demonstrated in a sodium-ion full-cell configuration which could deliver a sodiation capacity of over 300 mAh g -1 (based on anode) at 50 mA g -1 with more than 99% Coulombic efficiency. The results further exhort the prospects of melt-spun alloy anodes to realize fully functional sodium-ion batteries.

3D Reticular Li1.2Ni0.2Mn0.6O2 Cathode Material for Lithium-Ion Batteries.

PubMed

Li, Li; Wang, Lecai; Zhang, Xiaoxiao; Xue, Qing; Wei, Lei; Wu, Feng; Chen, Renjie

2017-01-18

In this study, a hard-templating route was developed to synthesize a 3D reticular Li 1.2 Ni 0.2 Mn 0.6 O 2 cathode material using ordered mesoporous silica as the hard template. The synthesized 3D reticular Li 1.2 Ni 0.2 Mn 0.6 O 2 microparticles consisted of two interlaced 3D nanonetworks and a mesopore channel system. When used as the cathode material in a lithium-ion battery, the as-synthesized 3D reticular Li 1.2 Ni 0.2 Mn 0.6 O 2 exhibited remarkably enhanced electrochemical performance, namely, superior rate capability and better cycling stability than those of its bulk counterpart. Specifically, a high discharge capacity of 195.6 mA h g -1 at 1 C with 95.6% capacity retention after 50 cycles was achieved with the 3D reticular Li 1.2 Ni 0.2 Mn 0.6 O 2 . A high discharge capacity of 135.7 mA h g -1 even at a high current of 1000 mA g -1 was also obtained. This excellent electrochemical performance of the 3D reticular Li 1.2 Ni 0.2 Mn 0.6 O 2 is attributed to its designed structure, which provided nanoscale lithium pathways, large specific surface area, good thermal and mechanical stability, and easy access to the material center.

Capacity Payments in Restructured Markets under Low and High Penetration Levels of Renewable Energy

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jenkin, Thomas; Beiter, Philipp; Margolis, Robert

There is considerable debate about the degree to which restructured markets perform successfully in their use of capacity markets. In providing appropriate incentives for new and existing generation to meet reliability requirements, a variety of capacity market designs have developed across RTOs and ISOs in the United States and internationally. Growing levels of variable renewable energy (VRE) resources arguably create new challenges for capacity market designs, because VREs suppress energy prices while providing relatively little capacity, with these effects increase with VRE penetration. The purpose of this report is threefold. First, we provide a brief outline of the purpose andmore » design of various capacity markets under consideration using variable resource requirement (VRR) demand curves. Second, we discuss some of the main challenges raised in existing literature and a set of interviews that we conducted with market participants, regulators, and observers, including where there substantive differences in opinion. Third, we consider some of the challenges that may be specific to higher penetration levels of VRE. While the well known 'merit order' effect from VRE can be expected to suppress wholesale energy prices and revenue, this may be partly mitigated by increased capacity payments and the greater importance of AS payments for flexible capacity. The potential for greater reliance on capacity markets for generator revenues may amplify any inefficiency and costs associated with capacity price volatility and other suboptimal market design choices. Regulatory intervention to ensure adequate capacity payments and ancillary service revenue may become more prevalent under current market designs as the timescale for market signals shifts increasingly from near term (e.g., day-ahead in wholesale electricity markets) to longer term (annual intervals in capacity markets). Our review and discussion with market participants suggest substantive challenges may remain in implementing capacity markets that provide both adequate operational and investment incentives, particularly under high-VRE scenarios with greater need for flexible capacity.« less

Facile fabrication of plate-shaped hydrohausmannite as electrode material for supercapacitors

NASA Astrophysics Data System (ADS)

Liang, Jun; Chai, Yao; Li, Deli; Li, Meng; Lu, Jiaxue; Li, Li; Luo, Min

2017-08-01

A simple and one-step solvothermal synthesis method has been developed to prepare two-dimensional (2-D) hydrohausmannite ((Mn4-2xMnx)Mn8O16-x(OH)x) nanoplates with radial length of 300 nm and thickness of about 25 nm in a binary ethanediamine/water solvent system. The formation mechanism of hydrohausmannite is suggested. As an anode material for electrochemical capacitors, the plate-shaped hydrohausmannite not only displays a high specific capacity (215 at 0.1 A g-1) and good rate capability, but also shows good stable performance along with 94% specific capacity retained after 3000 cycle tests. The method can be easily controlled and expected to be applicable for the large-scale preparation of the 2-D hydrohausmannite.

Silicene Flowers: A Dual Stabilized Silicon Building Block for High-Performance Lithium Battery Anodes.

PubMed

Zhang, Xinghao; Qiu, Xiongying; Kong, Debin; Zhou, Lu; Li, Zihao; Li, Xianglong; Zhi, Linjie

2017-07-25

Nanostructuring is a transformative way to improve the structure stability of high capacity silicon for lithium batteries. Yet, the interface instability issue remains and even propagates in the existing nanostructured silicon building blocks. Here we demonstrate an intrinsically dual stabilized silicon building block, namely silicene flowers, to simultaneously address the structure and interface stability issues. These original Si building blocks as lithium battery anodes exhibit extraordinary combined performance including high gravimetric capacity (2000 mAh g -1 at 800 mA g -1 ), high volumetric capacity (1799 mAh cm -3 ), remarkable rate capability (950 mAh g -1 at 8 A g -1 ), and excellent cycling stability (1100 mA h g -1 at 2000 mA g -1 over 600 cycles). Paired with a conventional cathode, the fabricated full cells deliver extraordinarily high specific energy and energy density (543 Wh kg ca -1 and 1257 Wh L ca -1 , respectively) based on the cathode and anode, which are 152% and 239% of their commercial counterparts using graphite anodes. Coupled with a simple, cost-effective, scalable synthesis approach, this silicon building block offers a horizon for the development of high-performance batteries.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Yun; Zhao, Mingyang; Khalid, Syed

The high voltage cathode material, LiMn 1.6Ni 0.4O 4, was prepared by a polymer-assisted method. The novelty of this paper is the substitution of Ni with Mn, which already exists in the crystal structure instead of other isovalent metal ion dopants which would result in capacity loss. The electrochemical performance testing including stability and rate capability was evaluated. The temperature was found to impose a change on the valence and structure of the cathode materials. Specifically, manganese tends to be reduced at a high temperature of 800 °C and leads to structural changes. The manganese substituted LiMn 1.5Ni 0.5O 4more » (LMN) has proved to be a good candidate material for Li-ion battery cathodes displaying good rate capability and capacity retention. Finally, the cathode materials processed at 550 °C showed a stable performance with negligible capacity loss for 400 cycles.« less

Embroidered Copper Microwire Current Collector for Improved Cycling Performance of Silicon Anodes in Lithium-Ion Batteries.

PubMed

Breitung, Ben; Aguiló-Aguayo, Noemí; Bechtold, Thomas; Hahn, Horst; Janek, Jürgen; Brezesinski, Torsten

2017-10-12

Si holds great promise as an alloying anode material for Li-ion batteries with improved energy density because of its high theoretical specific capacity and favorable operation voltage range. However, the large volume expansion of Si during electrochemical reaction with Li and the associated adverse effects strongly limit its prospect for application. Here, we report on the use of three-dimensional instead of flat current collectors for high-capacity Si anodes in an attempt to mitigate the loss of electrical contact of active electrode regions as a result of structural disintegration with cycling. The current collectors were produced by technical embroidery and consist of interconnected Cu wires of diameter <150 µm. In comparison to Si/Li cells using a conventional Cu foil current collector, the embroidered microwire network-based cells show much enhanced capacity and reversibility due to a higher degree of tolerance to cycling.

Enhanced capacity of chemically bonded phosphorus/carbon composite as an anode material for potassium-ion batteries

NASA Astrophysics Data System (ADS)

Wu, Xuan; Zhao, Wei; Wang, Hong; Qi, Xiujun; Xing, Zheng; Zhuang, Quanchao; Ju, Zhicheng

2018-02-01

Potassium-ion batteries are attracting great attention as a promising alternative to lithium-ion batteries due to the abundance and low price of potassium. Herein, the phosphorus/carbon composite, obtained by a simple ball-milling of 20 wt% commercial red phosphorus and 80 wt% graphite, is studied as a novel anode for potassium-ion batteries. Considering the high theoretical specific capacity of phosphorus and formation of stable phosphorus-carbon bond, which can alleviate the volume expansion efficiently, the phosphorus/carbon composite exhibits a high charge capacity of 323.5 mA h g-1 after 50 cycles at a current density of 50 mA g-1 with moderate rate capability and cycling stability. By the X-ray diffraction analysis, the alloying-dealloying mechanism of phosphorus is proposed to form a KP phase. Meanwhile, prepotassiation treatment is conducted to improve the low initial coulomb efficiency.

Mesoporous Li1.2Mn0.54Ni0.13Co0.13O2 nanotubes for high-performance cathodes in Li-ion batteries

NASA Astrophysics Data System (ADS)

Ma, Dingtao; Li, Yongliang; Zhang, Peixin; Cooper, Adam J.; Abdelkader, Amr M.; Ren, Xiangzhong; Deng, Libo

2016-04-01

One-dimensional nanotubes constructed from interconnected Li1.2Mn0.54Ni0.13Co0.13O2 secondary particles of diameters measuring ca. 40 nm, were synthesized by a one-pot electrospinning method. Novel electrodes were constructed from (a) nanoparticles only, and (b) hollow nanofibres, and employed as cathodes in Li-ion batteries. The nanotube cathode exhibited impressive specific charge capacity, good cycling stability, and excellent rate capability. A discharge capacity of 140 mAh g-1 with capacity retention of 89% at 3 C was achieved after 300 cycles. The significant improvement of electrochemical performance is attributed to the high surface area of the nanotubes, well-guided charge transfer kinetics with short ionic diffusion pathways, and large effective contact area with the electrolyte during the cycling process.

Graphene/Sulfur/Carbon Nanocomposite for High Performance Lithium-Sulfur Batteries

PubMed Central

Jin, Kangke; Zhou, Xufeng; Liu, Zhaoping

2015-01-01

Here, we report a two-step synthesis of graphene/sulfur/carbon ternary composite with a multilayer structure. In this composite, ultrathin S layers are uniformly deposited on graphene nanosheets and covered by a thin layer of amorphous carbon derived from β-cyclodextrin on the surface. Such a unique microstructure, not only improves the electrical conductivity of sulfur, but also effectively inhibits the dissolution of polysulfides during charging/discharging processes. As a result, this ternary nanocomposite exhibits excellent electrochemical performance. It can deliver a high initial discharge and charge capacity of 1410 mAh·g−1 and 1370 mAh·g−1, respectively, and a capacity retention of 63.8% can be achieved after 100 cycles at 0.1 C (1 C = 1675 mA·g−1). A relatively high specific capacity of 450 mAh·g−1 can still be retained after 200 cycles at a high rate of 2 C. The synthesis process introduced here is simple and broadly applicable to the modification of sulfur cathode for better electrochemical performance. PMID:28347077

Facile synthesis N-doped hollow carbon spheres from spherical solid silica.

PubMed

Wenelska, K; Ottmann, A; Moszyński, D; Schneider, P; Klingeler, R; Mijowska, E

2018-02-01

Nitrogen-doped core/shell carbon nanospheres (NHCS are prepared and their capability as an anode material in lithium-ion batteries is investigated. The synthesis methodology is based on a fast template route. The resulting molecular nanostructures are characterized by X-ray diffraction, transmission electron microscopy, thermal analysis, and nitrogen adsorption/desorption measurement as well as by cyclic voltammetry and galvanostatic cycling. The core/shell structure provides a rapid lithium transport pathway and boasts a highly reversible capacity. For undoped HCS the BET specific surface area is 623m 2 /g which increases up to 1000m 2 /g upon N-doping. While there is no significant effect of N-doping on the electrochemical performance at small scan rates, the doped NHCS shows better specific capacities than the pristine HCS at elevated rates. For instance, the discharge capacities in the 40th cycle, obtained at 1000mA/g, amount to 170mAh/g and 138mAh/g for NHCS and HCS, respectively. Copyright © 2017 Elsevier Inc. All rights reserved.

Accuracy statistics in predicting Independent Activities of Daily Living (IADL) capacity with comprehensive and brief neuropsychological test batteries.

PubMed

Karzmark, Peter; Deutsch, Gayle K

2018-01-01

This investigation was designed to determine the predictive accuracy of a comprehensive neuropsychological and brief neuropsychological test battery with regard to the capacity to perform instrumental activities of daily living (IADLs). Accuracy statistics that included measures of sensitivity, specificity, positive and negative predicted power and positive likelihood ratio were calculated for both types of batteries. The sample was drawn from a general neurological group of adults (n = 117) that included a number of older participants (age >55; n = 38). Standardized neuropsychological assessments were administered to all participants and were comprised of the Halstead Reitan Battery and portions of the Wechsler Adult Intelligence Scale-III. A comprehensive test battery yielded a moderate increase over base-rate in predictive accuracy that generalized to older individuals. There was only limited support for using a brief battery, for although sensitivity was high, specificity was low. We found that a comprehensive neuropsychological test battery provided good classification accuracy for predicting IADL capacity.

Excess lithium storage in LiFePO4-Carbon interface by ball-milling

NASA Astrophysics Data System (ADS)

Guo, Hua; Song, Xiaohe; Zheng, Jiaxin; Pan, Feng

2016-07-01

As one of the most popular cathode materials for high power lithium ion batteries (LIBs) of the electrical-vehicle (EV), lithium iron phosphate (LiFePO4 (LFP)) is limited to its relatively lower theoretical specific capacity of 170mAh g-1. To break the limits and further improve the capacity of LFP is promising but challenging. In this study, the ball-milling method is applied to the mixture of LFP and carbon, and the effective capacity larger than the theoretical one by 30mAh g-1 is achieved. It is demonstrated that ball-milling leads to the LFP-Carbon interface to store the excess Li-ions.

ELECTRIC IMPEDANCE OF ASTERIAS EGGS

PubMed Central

Cole, Kenneth S.; Cole, Robert H.

1936-01-01

The alternating current resistance and capacity of suspensions of unfertilized eggs of Asterias forbesi have been measured at frequencies from one thousand to sixteen million cycles per second. The plasma membrane of the egg has a static capacity of 1.10µf/cm.2 which is practically independent of frequency. The suspensions show a capacity dependent on frequency at low frequencies which may be attributable to surface conductance. The specific resistance of the cytoplasm is between 136 and 225 ohm cm. (4 to 7 times sea water), indicating a relatively high concentration of non-electrolytes. At frequencies above one million cycles there is definite evidence of another element of which the nucleus is presumably a part. PMID:19872951

High surface area nanocrystalline hausmannite synthesized by a solvent-free route

DOE Office of Scientific and Technical Information (OSTI.GOV)

Herrera-Miranda, Daniel; Ponrouch, Alexandre; Pons, Josefina

Highlights: ► High surface area Mn{sub 3}O{sub 4} nanoparticles obtained by a solvent-free low temperature route. ► 3,6,9-Trioxadecanoic acid allows to obtain nanocrystalline hausmannite. ► Tape casted electrodes show up to 300 mAh g{sup −1} capacity after more than 40 cycles at a C/3 rate. ► Upper cut off voltage strongly influences capacity retention upon cycling at high C rates. -- Abstract: Nanocrystalline high surface area Mn{sub 3}O{sub 4} powder was obtained at low temperature by a solvent-free route. The precursor was a mixture of manganese (II) acetate, 3,6,9-trioxadecanoic acid (TODA) and ammonium acetate that were intimately mixed by groundingmore » in an agate mortar. Nanocrystalline Mn{sub 3}O{sub 4} was obtained by thermal treatment at 120 °C. Powder X-ray diffraction, selected area electron diffraction, high resolution transmission electron microscopy, and Fourier transformed infrared characterization confirmed the formation of the hausmannite phase. The as-prepared mesoporous material has high specific surface area (120 m{sup 2} g{sup −1}). The performances of tape casted Mn{sub 3}O{sub 4} nanopowder electrodes were investigated as anode material for lithium ion batteries. High capacity values were achieved at diverse C rates. Capacity fading was found to be dependent on the upper cut off voltage, the presence of a plateau at 2.25 V vs. Li{sup +}/Li being detrimental for long term cyclability.« less

Facile synthesis of zwitterionic polymer-coated core-shell magnetic nanoparticles for highly specific capture of N-linked glycopeptides.

PubMed

Chen, Yajing; Xiong, Zhichao; Zhang, Lingyi; Zhao, Jiaying; Zhang, Quanqing; Peng, Li; Zhang, Weibing; Ye, Mingliang; Zou, Hanfa

2015-02-21

Highly selective and efficient capture of glycosylated proteins and peptides from complex biological samples is of profound significance for the discovery of disease biomarkers in biological systems. Recently, hydrophilic interaction liquid chromatography (HILIC)-based functional materials have been extensively utilized for glycopeptide enrichment. However, the low amount of immobilized hydrophilic groups on the affinity material has limited its specificity, detection sensitivity and binding capacity in the capture of glycopeptides. Herein, a novel affinity material was synthesized to improve the binding capacity and detection sensitivity for glycopeptides by coating a poly(2-(methacryloyloxy)ethyl)-dimethyl-(3-sulfopropyl) ammonium hydroxide (PMSA) shell onto Fe3O4@SiO2 nanoparticles, taking advantage of reflux-precipitation polymerization for the first time (denoted as Fe3O4@SiO2@PMSA). The thick polymer shell endows the nanoparticles with excellent hydrophilic property and several functional groups on the polymer chains. The resulting Fe3O4@SiO2@PMSA demonstrated an outstanding ability for glycopeptide enrichment with high selectivity, extremely high detection sensitivity (0.1 fmol), large binding capacity (100 mg g(-1)), high enrichment recovery (above 73.6%) and rapid magnetic separation. Furthermore, in the analysis of real complicated biological samples, 905 unique N-glycosylation sites from 458 N-glycosylated proteins were reliably identified in three replicate analyses of a 65 μg protein sample extracted from mouse liver, showing the great potential of Fe3O4@SiO2@PMSA in the detection and identification of low-abundance N-linked glycopeptides in biological samples.

A Fluorinated Ether Electrolyte Enabled High Performance Prelithiated Graphite/Sulfur Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chen, Shuru; Yu, Zhaoxin; Gordin, Mikhail L.

Lithium/sulfur (Li/S) batteries have attracted great attention as a promising energy storage technology, but so far their practical applications are greatly hindered by issues of polysulfide shuttling and unstable lithium/electrolyte interface. To address these issues, a feasible strategy is to construct a rechargeable prelithiated graphite/sulfur batteries. In this study, a fluorinated ether of bis(2,2,2-trifluoroethyl) ether (BTFE) was reported to blend with 1,3-dioxolane (DOL) for making a multifunctional electrolyte of 1.0 M LiTFSI DOL/BTFE (1:1, v/v) to enable high performance prelithiated graphite/S batteries. First, the electrolyte significantly reduces polysulfide solubility to suppress the deleterious polysulfide shuttling and thus improves capacity retentionmore » of sulfur cathodes. Second, thanks to the low viscosity and good wettability, the fluorinated electrolyte dramatically enhances the reaction kinetics and sulfur utilization of high-areal-loading sulfur cathodes. More importantly, this electrolyte forms a stable solid-electrolyte interphase (SEI) layer on graphite surface and thus enables remarkable cyclability of graphite anodes. Lastly, by coupling prelithiated graphite anodes with sulfur cathodes with high areal capacity of ~3 mAh cm -2, we demonstrate prelithiated graphite/sulfur batteries that show high sulfur-specific capacity of ~1000 mAh g -1 and an excellent capacity retention of >65% after 450 cycles at C/10.« less

A Fluorinated Ether Electrolyte Enabled High Performance Prelithiated Graphite/Sulfur Batteries

DOE PAGES

Chen, Shuru; Yu, Zhaoxin; Gordin, Mikhail L.; ...

2017-02-03

Lithium/sulfur (Li/S) batteries have attracted great attention as a promising energy storage technology, but so far their practical applications are greatly hindered by issues of polysulfide shuttling and unstable lithium/electrolyte interface. To address these issues, a feasible strategy is to construct a rechargeable prelithiated graphite/sulfur batteries. In this study, a fluorinated ether of bis(2,2,2-trifluoroethyl) ether (BTFE) was reported to blend with 1,3-dioxolane (DOL) for making a multifunctional electrolyte of 1.0 M LiTFSI DOL/BTFE (1:1, v/v) to enable high performance prelithiated graphite/S batteries. First, the electrolyte significantly reduces polysulfide solubility to suppress the deleterious polysulfide shuttling and thus improves capacity retentionmore » of sulfur cathodes. Second, thanks to the low viscosity and good wettability, the fluorinated electrolyte dramatically enhances the reaction kinetics and sulfur utilization of high-areal-loading sulfur cathodes. More importantly, this electrolyte forms a stable solid-electrolyte interphase (SEI) layer on graphite surface and thus enables remarkable cyclability of graphite anodes. Lastly, by coupling prelithiated graphite anodes with sulfur cathodes with high areal capacity of ~3 mAh cm -2, we demonstrate prelithiated graphite/sulfur batteries that show high sulfur-specific capacity of ~1000 mAh g -1 and an excellent capacity retention of >65% after 450 cycles at C/10.« less

How Do World-Class Nordic Combined Athletes Differ From Specialized Cross-Country Skiers and Ski Jumpers in Sport-Specific Capacity and Training Characteristics?

PubMed

Sandbakk, Øyvind; Rasdal, Vegard; Bråten, Steinar; Moen, Frode; Ettema, Gertjan

2016-10-01

To compare sport-specific laboratory capacities and the annual training of world-class Nordic combined (NC) athletes with specialized ski jumpers (SJ) and cross-country (XC) skiers. Five world-class athletes from each sports discipline were compared. Ski jump imitations were performed on a 3-dimensional force plate in NC athletes and SJ, whereas XC skiing characteristics were obtained from submaximal and maximal roller ski skating on a treadmill in NC athletes and XC skiers. In addition, anthropometrics and annual training characteristics were determined. NC athletes demonstrated 9% higher body mass and showed 17% lower vertical speed in the ski jump imitation than SJ (all P < .05). NC athletes had 12% lower body mass and showed 10% lower peak treadmill speed and 12% lower body-mass-normalized peak oxygen uptake than XC skiers (all P < .05). NC athletes performed half the number of ski-jumping-specific sessions and outdoor ski jumps compared with SJ. NC athletes performed 31% less endurance training, mainly caused by lower amounts of low- and moderate-intensity training in the classical technique, whereas high-intensity strength and speed training and endurance training in the skating technique did not differ substantially from XC skiers. To simultaneously optimize endurance, explosive, and technical capacities in 2 different disciplines, world-class NC athletes train approximately two-thirds of the XC skier's endurance training volume and perform one-half of the ski-jump-specific training compared with SJ. Still, the various laboratory capacities differed only 10-17% compared with SJ and XC skiers.

49 CFR 179.220-16 - Expansion capacity.

Code of Federal Regulations, 2012 CFR

2012-10-01

... Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) SPECIFICATIONS FOR TANK CARS Specifications for Non-Pressure Tank Car Tanks (Classes DOT-111AW and 115AW) § 179.220-16 Expansion capacity. Expansion capacity...

Light-weight free-standing carbon nanotube-silicon films for anodes of lithium ion batteries.

PubMed

Cui, Li-Feng; Hu, Liangbing; Choi, Jang Wook; Cui, Yi

2010-07-27

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network functions as both mechanical support and electrical conductor and Si as a high capacity anode material for Li-ion battery. Such free-standing film has a low sheet resistance of approximately 30 Ohm/sq. It shows a high specific charge storage capacity (approximately 2000 mAh/g) and a good cycling life, superior to pure sputtered-on silicon films with similar thicknesses. Scanning electron micrographs show that Si is still connected by the CNT network even when small breaking or cracks appear in the film after cycling. The film can also "ripple up" to release the strain of a large volume change during lithium intercalation. The conductive composite film can function as both anode active material and current collector. It offers approximately 10 times improvement in specific capacity compared with widely used graphite/copper anode sheets.

The relationship of training load to physical-capacity changes during international tours in high-performance junior tennis players.

PubMed

Murphy, Alistair P; Duffield, Rob; Kellett, Aaron; Reid, Machar

2015-03-01

Given the travel that punctuates junior tennis development, an understanding of the changes in fitness owing to touring and the association between training loads (TLs) and fitness on return is vital. The authors investigated physical-capacity changes from pretour to posttour, determining if those changes were related to the TL of athletes on tour. Thirty junior athletes completed fitness testing before and after 4-wk tours. Testing included double-leg countermovement jump (CMJ), dominant single-leg and nondominant single-leg CMJ, speed (5, 10, 20 m), modified 5-0-5 agility (left and right), 10 × 20-m repeated-sprint ability (RSA), and multistage fitness tests. Repeated-measures ANOVAs determined physical-capacity change, with effect-size analysis establishing the magnitude of change. To avoid regression toward the mean, a 1/3-split technique was implemented for comparative analysis (high to low TLs). Moderate effects (d=0.50-0.70) for reductions of up to 3.6% in 5-, 10-, and 20-m speeds were observed. However, all remaining changes were only of trivial to small magnitude (d<0.40). Closer analysis of the interaction between TL and physical capacities (1/3-split) revealed that subjects who completed the greatest amount of total and tennis TL returned with a greater decline in speed and aerobic capacities (d>0.80). Furthermore, it was observed that match load dictates on- and off-court TL, with an increase in matches won understandably stunting exposure to off-court TL. Specific training should be prescribed on tour to maintain speed characteristics over a 4-wk international tour. On-tour training schedules should be carefully monitored to maximize specific TL exposure after losses on tour.

From Metal-Organic Framework to Li2S@C-Co-N Nanoporous Architecture: A High-Capacity Cathode for Lithium-Sulfur Batteries.

PubMed

He, Jiarui; Chen, Yuanfu; Lv, Weiqiang; Wen, Kechun; Xu, Chen; Zhang, Wanli; Li, Yanrong; Qin, Wu; He, Weidong

2016-12-27

Owing to the high theoretical specific capacity (1166 mAh g -1 ), lithium sulfide (Li 2 S) has been considered as a promising cathode material for Li-S batteries. However, the polysulfide dissolution and low electronic conductivity of Li 2 S limit its further application in next-generation Li-S batteries. In this report, a nanoporous Li 2 S@C-Co-N cathode is synthesized by liquid infiltration-evaporation of ultrafine Li 2 S nanoparticles into graphitic carbon co-doped with cobalt and nitrogen (C-Co-N) derived from metal-organic frameworks. The obtained Li 2 S@C-Co-N architecture remarkably immobilizes Li 2 S within the cathode structure through physical and chemical molecular interactions. Owing to the synergistic interactions between C-Co-N and Li 2 S nanoparticles, the Li 2 S@C-Co-N composite delivers a reversible capacity of 1155.3 (99.1% of theoretical value) at the initial cycle and 929.6 mAh g -1 after 300 cycles, with nearly 100% Coulombic efficiency and a capacity fading of 0.06% per cycle. It exhibits excellent rate capacities of 950.6, 898.8, and 604.1 mAh g -1 at 1C, 2C, and 4C, respectively. Such a cathode structure is promising for practical applications in high-performance Li-S batteries.

Importance of polypyrrole in constructing 3D hierarchical carbon nanotube@MnO2 perfect core-shell nanostructures for high-performance flexible supercapacitors

NASA Astrophysics Data System (ADS)

Zhou, Jinyuan; Zhao, Hao; Mu, Xuemei; Chen, Jiayi; Zhang, Peng; Wang, Yaling; He, Yongmin; Zhang, Zhenxing; Pan, Xiaojun; Xie, Erqing

2015-08-01

This study reports the preparation of 3D hierarchical carbon nanotube (CNT) @MnO2 core-shell nanostructures under the assistance of polypyrrole (PPy). The as-prepared CNT@PPy@MnO2 core-shell structures show a perfect coating of MnO2 on each CNT and, more importantly, a robust bush-like pseudocapacitive shell to effectively increase the specific surface area and enhance the ion accessibility. As expected, a high specific capacity of 490-530 F g-1 has been achieved from CNT@PPy@MnO2 single electrodes. And about 98.5% of the capacity is retained after 1000 charge/discharge cycles at a current density of 5 A g-1. Furthermore, the assembled asymmetric CNT@PPy@MnO2//AC capacitors show the maximum energy density of 38.42 W h kg-1 (2.24 mW h cm-3) at a power density of 100 W kg-1 (5.83 mW cm-3), and they maintain 59.52% of the initial value at 10 000 W kg-1 (0.583 W cm-3). In addition, the assembled devices show high cycling stabilities (89.7% after 2000 cycles for asymmetric and 87.2% for symmetric), and a high bending stability (64.74% after 200 bending tests). This ability to obtain high energy densities at high power rates while maintaining high cycling stability demonstrates that this well-designed structure could be a promising electrode material for high-performance supercapacitors.This study reports the preparation of 3D hierarchical carbon nanotube (CNT) @MnO2 core-shell nanostructures under the assistance of polypyrrole (PPy). The as-prepared CNT@PPy@MnO2 core-shell structures show a perfect coating of MnO2 on each CNT and, more importantly, a robust bush-like pseudocapacitive shell to effectively increase the specific surface area and enhance the ion accessibility. As expected, a high specific capacity of 490-530 F g-1 has been achieved from CNT@PPy@MnO2 single electrodes. And about 98.5% of the capacity is retained after 1000 charge/discharge cycles at a current density of 5 A g-1. Furthermore, the assembled asymmetric CNT@PPy@MnO2//AC capacitors show the maximum energy density of 38.42 W h kg-1 (2.24 mW h cm-3) at a power density of 100 W kg-1 (5.83 mW cm-3), and they maintain 59.52% of the initial value at 10 000 W kg-1 (0.583 W cm-3). In addition, the assembled devices show high cycling stabilities (89.7% after 2000 cycles for asymmetric and 87.2% for symmetric), and a high bending stability (64.74% after 200 bending tests). This ability to obtain high energy densities at high power rates while maintaining high cycling stability demonstrates that this well-designed structure could be a promising electrode material for high-performance supercapacitors. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr03426d

Potential Large Decadal Missions Enabled by Nasas Space Launch System

NASA Technical Reports Server (NTRS)

Stahl, H. Philip; Hopkins, Randall C.; Schnell, Andrew; Smith, David Alan; Jackman, Angela; Warfield, Keith R.

2016-01-01

Large space telescope missions have always been limited by their launch vehicle's mass and volume capacities. The Hubble Space Telescope (HST) was specifically designed to fit inside the Space Shuttle and the James Webb Space Telescope (JWST) is specifically designed to fit inside an Ariane 5. Astrophysicists desire even larger space telescopes. NASA's "Enduring Quests Daring Visions" report calls for an 8- to 16-m Large UV-Optical-IR (LUVOIR) Surveyor mission to enable ultra-high-contrast spectroscopy and coronagraphy. AURA's "From Cosmic Birth to Living Earth" report calls for a 12-m class High-Definition Space Telescope to pursue transformational scientific discoveries. NASA's "Planning for the 2020 Decadal Survey" calls for a Habitable Exoplanet Imaging (HabEx) and a LUVOIR as well as Far-IR and an X-Ray Surveyor missions. Packaging larger space telescopes into existing launch vehicles is a significant engineering complexity challenge that drives cost and risk. NASA's planned Space Launch System (SLS), with its 8 or 10-m diameter fairings and ability to deliver 35 to 45-mt of payload to Sun-Earth-Lagrange-2, mitigates this challenge by fundamentally changing the design paradigm for large space telescopes. This paper reviews the mass and volume capacities of the planned SLS, discusses potential implications of these capacities for designing large space telescope missions, and gives three specific mission concept implementation examples: a 4-m monolithic off-axis telescope, an 8-m monolithic on-axis telescope and a 12-m segmented on-axis telescope.

Potential large missions enabled by NASA's space launch system

NASA Astrophysics Data System (ADS)

Stahl, H. Philip; Hopkins, Randall C.; Schnell, Andrew; Smith, David A.; Jackman, Angela; Warfield, Keith R.

2016-07-01

Large space telescope missions have always been limited by their launch vehicle's mass and volume capacities. The Hubble Space Telescope (HST) was specifically designed to fit inside the Space Shuttle and the James Webb Space Telescope (JWST) is specifically designed to fit inside an Ariane 5. Astrophysicists desire even larger space telescopes. NASA's "Enduring Quests Daring Visions" report calls for an 8- to 16-m Large UV-Optical-IR (LUVOIR) Surveyor mission to enable ultra-high-contrast spectroscopy and coronagraphy. AURA's "From Cosmic Birth to Living Earth" report calls for a 12-m class High-Definition Space Telescope to pursue transformational scientific discoveries. NASA's "Planning for the 2020 Decadal Survey" calls for a Habitable Exoplanet Imaging (HabEx) and a LUVOIR as well as Far-IR and an X-Ray Surveyor missions. Packaging larger space telescopes into existing launch vehicles is a significant engineering complexity challenge that drives cost and risk. NASA's planned Space Launch System (SLS), with its 8 or 10-m diameter fairings and ability to deliver 35 to 45-mt of payload to Sun-Earth-Lagrange-2, mitigates this challenge by fundamentally changing the design paradigm for large space telescopes. This paper reviews the mass and volume capacities of the planned SLS, discusses potential implications of these capacities for designing large space telescope missions, and gives three specific mission concept implementation examples: a 4-m monolithic off-axis telescope, an 8-m monolithic on-axis telescope and a 12-m segmented on-axis telescope.

High-cost, high-capacity backbone for global brain communication.

PubMed

van den Heuvel, Martijn P; Kahn, René S; Goñi, Joaquín; Sporns, Olaf

2012-07-10

Network studies of human brain structural connectivity have identified a specific set of brain regions that are both highly connected and highly central. Recent analyses have shown that these putative hub regions are mutually and densely interconnected, forming a "rich club" within the human brain. Here we show that the set of pathways linking rich club regions forms a central high-cost, high-capacity backbone for global brain communication. Diffusion tensor imaging (DTI) data of two sets of 40 healthy subjects were used to map structural brain networks. The contributions to network cost and communication capacity of global cortico-cortical connections were assessed through measures of their topology and spatial embedding. Rich club connections were found to be more costly than predicted by their density alone and accounted for 40% of the total communication cost. Furthermore, 69% of all minimally short paths between node pairs were found to travel through the rich club and a large proportion of these communication paths consisted of ordered sequences of edges ("path motifs") that first fed into, then traversed, and finally exited the rich club, while passing through nodes of increasing and then decreasing degree. The prevalence of short paths that follow such ordered degree sequences suggests that neural communication might take advantage of strategies for dynamic routing of information between brain regions, with an important role for a highly central rich club. Taken together, our results show that rich club connections make an important contribution to interregional signal traffic, forming a central high-cost, high-capacity backbone for global brain communication.

Superior Sodium Storage in 3D Interconnected Nitrogen and Oxygen Dual-Doped Carbon Network.

PubMed

Wang, Min; Yang, Zhenzhong; Li, Weihan; Gu, Lin; Yu, Yan

2016-05-01

Carbonaceous materials have attracted immense interest as anode materials for Na-ion batteries (NIBs) because of their good chemical, thermal stabilities, as well as high Na-storage capacity. However, the carbonaceous materials as anodes for NIBs still suffer from the lower rate capability and poor cycle life. An N,O-dual doped carbon (denoted as NOC) network is designed and synthesized, which is greatly favorable for sodium storage. It exhibits high specific capacity and ultralong cycling stability, delivering a capacity of 545 mAh g(-1) at 100 mA g(-1) after 100 cycles and retaining a capacity of 240 mAh g(-1) at 2 A g(-1) after 2000 cycles. The NOC composite with 3D well-defined porosity and N,O-dual doped induces active sites, contributing to the enhanced sodium storage. In addition, the NOC is synthesized through a facile solution process, which can be easily extended to the preparation of many other N,O-dual doped carbonaceous materials for wide applications in catalysis, energy storage, and solar cells. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhanced aging properties of HKUST-1 in hydrophobic mixed-matrix membranes for ammonia adsorption.

PubMed

DeCoste, Jared B; Denny, Michael S; Peterson, Gregory W; Mahle, John J; Cohen, Seth M

2016-04-21

Metal-organic frameworks (MOFs) in their free powder form have exhibited superior capacities for many gases when compared to other materials, due to their tailorable functionality and high surface areas. Specifically, the MOF HKUST-1 binds small Lewis bases, such as ammonia, with its coordinatively unsaturated copper sites. We describe here the use of HKUST-1 in mixed-matrix membranes (MMMs) prepared from polyvinylidene difluoride (PVDF) for the removal of ammonia gas. These MMMs exhibit ammonia capacities similar to their hypothetical capacities based on the weight percent of HKUST-1 in each MMM. HKUST-1 in its powder form is unstable toward humid conditions; however, upon exposure to humid environments for prolonged periods of time, the HKUST-1 MMMs exhibit outstanding structural stability, and maintain their ammonia capacity. Overall, this study has achieved all of the critical and combined elements for real-world applications of MOFs: high MOF loadings, fully accessible MOF surfaces, enhanced MOF stabilization, recyclability, mechanical stability, and processability. This study is a critical step in advancing MOFs to a stable, usable, and enabling technology.

Free-Standing Porous Carbon Nanofiber/Carbon Nanotube Film as Sulfur Immobilizer with High Areal Capacity for Lithium-Sulfur Battery.

PubMed

Zhang, Ye-Zheng; Zhang, Ze; Liu, Sheng; Li, Guo-Ran; Gao, Xue-Ping

2018-03-14

Low sulfur utilization and poor cycle life of the sulfur cathode with high sulfur loadings remain a great challenge for lithium-sulfur (Li-S) battery. Herein, the free-standing carbon film consisting of porous carbon nanofibers (PCNFs) and carbon nanotubes (CNTs) is successfully fabricated by the electrospinning technology. The PCNF/CNT film with three-dimensional and interconnected structure is promising for the uniformity of the high-loading sulfur, good penetration of the electrolyte, and reliable accommodation of volumetric expansion of the sulfur cathode. In addition, the abundant N/O-doped elements in PCNF/CNT film are helpful to chemically trap soluble polysulfides in the charge-discharge processes. Consequently, the obtained monolayer S/PCNF/CNT film as the cathode shows high specific capacity, excellent cycle stability, and rate stability with the sulfur loading of 3.9 mg cm -2 . Moreover, the high areal capacity of 13.5 mA h cm -2 is obtained for the cathode by stacking three S/PCNF/CNT layers with the high sulfur loading of 12 mg cm -2 . The stacking-layered cathode with high sulfur loading provides excellent cycle stability, which is beneficial to fabricate high-energy-density Li-S battery in future.

700 F hybrid capacitors cells composed of activated carbon and Li4Ti5O12 microspheres with ultra-long cycle life

NASA Astrophysics Data System (ADS)

Ruan, Dianbo; Kim, Myeong-Seong; Yang, Bin; Qin, Jun; Kim, Kwang-Bum; Lee, Sang-Hyun; Liu, Qiuxiang; Tan, Lei; Qiao, Zhijun

2017-10-01

To address the large-scale application demands of high energy density, high power density, and long cycle lifetime, 700-F hybrid capacitor pouch cells have been prepared, comprising ∼240-μm-thick activated carbon cathodes, and ∼60-μm-thick Li4Ti5O12 anodes. Microspherical Li4Ti5O12 (M-LTO) synthesized by spray-drying features 200-400 nm primary particles and interconnected nanopore structures. M-LTO half-cells exhibits high specific capacities (175 mAhh g-1), good rate capabilities (148 mAhh g-1 at 20 C), and ultra-long cycling stabilities (90% specific capacity retention after 10,000 cycles). In addition, the obtained hybrid capacitors comprising activated carbon (AC) and M-LTO shows excellent cell performances, achieving a maximum energy density of 51.65 Wh kg-1, a maximum power density of 2466 W kg-1, and ∼92% capacitance retention after 10,000 cycles, thus meeting the demands for large-scale applications such as trolleybuses.

Sulfur based electrode materials for secondary batteries

NASA Astrophysics Data System (ADS)

Hao, Yong

Developing next generation secondary batteries has attracted much attention in recent years due to the increasing demand of high energy and high power density energy storage for portable electronics, electric vehicles and renewable sources of energy. This dissertation investigates sulfur based advanced electrode materials in Lithium/Sodium batteries. The electrochemical performances of the electrode materials have been enhanced due to their unique nano structures as well as the formation of novel composites. First, a nitrogen-doped graphene nanosheets/sulfur (NGNSs/S) composite was synthesized via a facile chemical reaction deposition. In this composite, NGNSs were employed as a conductive host to entrap S/polysulfides in the cathode part. The NGNSs/S composite delivered an initial discharge capacity of 856.7 mAh g-1 and a reversible capacity of 319.3 mAh g-1 at 0.1C with good recoverable rate capability. Second, NGNS/S nanocomposites, synthesized using chemical reaction-deposition method and low temperature heat treatment, were further studied as active cathode materials for room temperature Na-S batteries. Both high loading composite with 86% gamma-S8 and low loading composite with 25% gamma-S8 have been electrochemically evaluated and compared with both NGNS and S control electrodes. It was found that low loading NGNS/S composite exhibited better electrochemical performance with specific capacity of 110 and 48 mAh g-1 at 0.1C at the 1st and 300th cycle, respectively. The Coulombic efficiency of 100% was obtained at the 300th cycle. Third, high purity rock-salt (RS), zinc-blende (ZB) and wurtzite (WZ) MnS nanocrystals with different morphologies were successfully synthesized via a facile solvothermal method. RS-, ZB- and WZ-MnS electrodes showed the capacities of 232.5 mAh g-1, 287.9 mAh g-1 and 79.8 mAh g-1 at the 600th cycle, respectively. ZB-MnS displayed the best performance in terms of specific capacity and cyclability. Interestingly, MnS electrodes exhibited an unusual phenomenon of capacity increase upon cycling which was ascribed to the decreased cell resistance and enhanced interfacial charge storage. In summary, this dissertation provides investigation of sulfur based electrode materials with sulfur/N-doped graphene composites and MnS nanocrystals. Their electrochemical performances have been evaluated and discussed. The understanding of their reaction mechanisms and electrochemical enhancement could make progress on development of secondary batteries.

Assessing capacity to consent to treatment with cholinesterase inhibitors in dementia using a specific and standardized version of the MacArthur Competence Assessment Tool (MacCAT-T).

PubMed

Mueller, Tanja; Haberstroh, Julia; Knebel, Maren; Oswald, Frank; Kaspar, Roman; Kemper, Christoph J; Halder-Sinn, Petra; Schroeder, Johannes; Pantel, Johannes

2017-02-01

The use of assessment tools has been shown to improve the inter-rater reliability of capacity assessments. However, instrument-based capacity assessments of people with dementia face challenges. In dementia research, measuring capacity with instruments like the MacArthur Competence Assessment Tool for Treatment (MacCAT-T) mostly employ hypothetical treatment vignettes that can overwhelm the abstraction capabilities of people with dementia and are thus not always suitable for this target group. The primary aim of this study was to provide a standardized real informed consent paradigm that enables the dementia-specific properties of capacity to consent to treatment in people with dementia to be identified in a real informed consent process that is both externally valid and ethically justifiable. The sample consisted of 53 people with mild to moderate dementia and a group of 133 people without cognitive impairment. Rather than using a hypothetical treatment vignette, we used a standardized version of the MacCAT-T to assess capacity to consent to treatment with cholinesterase inhibitors in people with dementia. Inter-rater reliability, item statistics, and psychometric properties were also investigated. Intraclass correlations (ICCs) (0.951-0.990) indicated high inter-rater reliability of the standardized real informed consent paradigm. In the dementia group, performance on different items of the MacCAT-T varied. Most people with dementia were able to express a treatment choice, and were aware of the need to take a tablet. Further information on the course of the disorder and the benefits and risks of the treatment were less understood, as was comparative reasoning regarding treatment alternatives. The standardized real informed consent paradigm enabled us to detect dementia-specific characteristics of patients' capacity to consent to treatment with cholinesterase inhibitors. In order to determine suitable enhanced consent procedures for this treatment, we recommend the consideration of MacCAT-T results on an item level. People with dementia seem to understand only basic information. Our data indicate that one useful strategy to enhance capacity to consent is to reduce attention and memory demands as far as possible.

Structural and Electrochemical Study of Hierarchical LiNi(1/3)Co(1/3)Mn(1/3)O2 Cathode Material for Lithium-Ion Batteries.

PubMed

Li, Li; Wang, Lecai; Zhang, Xiaoxiao; Xie, Man; Wu, Feng; Chen, Renjie

2015-10-07

In this study, a facile nanoetching-template route is developed to synthesize porous nanomicrohierarchical LiNi1/3Co1/3Mn1/3O2 microspheres with diameters below 1.5 μm, using porous CoMnO3 binary oxide microspheres as the template. The unique morphology of CoMnO3 template originates from the contraction effect during the oxidative decomposition of Ca0.2Mn0.4Co0.4CO3 precursors and is further improved by selectively removing calcium carbonate with a nanoetching process after calcination. The as-synthesized LiNi1/3Co1/3Mn1/3O2 microsphere, composed of numerous primary particles and pores with size of dozens of nanometers, illustrates a well-assembled porous nanomicrohierarchical structure. When used as the cathode material for lithium-ion batteries, the as-synthesized microspheres exhibit remarkably enhanced electrochemical performances with higher capacity, excellent cycling stability, and better rate capability, compared with the bulk counterpart. Specifically, hierarchical LiNi1/3Co1/3Mn1/3O2 achieves a high discharge capacity of 159.6 mA h g(-1) at 0.2 C with 98.7% capacity retention after 75 cycles and 133.2 mA h g(-1) at 1 C with 90% capacity retention after 100 cycles. A high discharge capacity of 135.5 mA h g(-1) even at a high current of 750 mA g(-1) (5 C) is also achieved. The nanoetching-template method can provide a general approach to improve cycling stability and rate capability of high capacity cathode materials for lithium-ion batteries.

Toward Aerogel Electrodes of Superior Rate Performance in Supercapacitors through Engineered Hollow Nanoparticles of NiCo2O4.

PubMed

Li, Jianjiang; Chen, Shuai; Zhu, Xiaoyi; She, Xilin; Liu, Tongchao; Zhang, Huawei; Komarneni, Sridhar; Yang, Dongjiang; Yao, Xiangdong

2017-12-01

A biomass-templated pathway is developed for scalable synthesis of NiCo 2 O 4 @carbon aerogel electrodes for supercapacitors, where NiCo 2 O 4 hollow nanoparticles with an average outer diameter of 30-40 nm are conjoined by graphitic carbon forming a 3D aerogel structure. This kind of NiCo 2 O 4 aerogel structure shows large specific surface area (167.8 m 2 g -1 ), high specific capacitance (903.2 F g -1 at a current density of 1 A g -1 ), outstanding rate performance (96.2% capacity retention from 1 to 10 A g -1 ), and excellent cycling stability (nearly without capacitance loss after 3000 cycles at 10 A g -1 ). The unique structure of the 3D hollow aerogel synergistically contributes to the high performance. For instance, the 3D interconnected porous structure of the aerogel is beneficial for electrolyte ion diffusion and for shortening the electron transport pathways, and thus can improve the rate performance. The conductive carbon joint greatly enhances the specific capacity, and the hollow structure prohibits the volume changes during the charge-discharge process to significantly improve the cycling stability. This work represents a giant step toward the preparation of high-performance commercial supercapacitors.

Self-assembling synthesis of free-standing nanoporous graphene-transition-metal oxide flexible electrodes for high-performance lithium-ion batteries and supercapacitors.

PubMed

Huang, Xiaodan; Sun, Bing; Chen, Shuangqiang; Wang, Guoxiu

2014-01-01

The synthesis of nanoporous graphene by a convenient carbon nanofiber assisted self-assembly approach is reported. Porous structures with large pore volumes, high surface areas, and well-controlled pore sizes were achieved by employing spherical silica as hard templates with different diameters. Through a general wet-immersion method, transition-metal oxide (Fe3O4, Co3O4, NiO) nanocrystals can be easily loaded into nanoporous graphene papers to form three-dimensional flexible nanoarchitectures. When directly applied as electrodes in lithium-ion batteries and supercapacitors, the materials exhibited superior electrochemical performances, including an ultra-high specific capacity, an extended long cycle life, and a high rate capability. In particular, nanoporous Fe3O4-graphene composites can deliver a reversible specific capacity of 1427.5 mAh g(-1) at a high current density of 1000 mA g(-1) as anode materials in lithium-ion batteries. Furthermore, nanoporous Co3O4-graphene composites achieved a high supercapacitance of 424.2 F g(-1) . This work demonstrated that the as-developed freestanding nanoporous graphene papers could have significant potential for energy storage and conversion applications. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three-Dimensionally Hierarchical Graphene Based Aerogel Encapsulated Sulfur as Cathode for Lithium/Sulfur Batteries

PubMed Central

Li, Haipeng; Sun, Liancheng; Wang, Zhuo; Zhang, Yongguang; Tan, Taizhe; Wang, Gongkai

2018-01-01

A simple and effective method was developed to obtain the electrode for lithium/sulfur (Li/S) batteries with high specific capacity and cycling durability via adopting an interconnected sulfur/activated carbon/graphene (reduced graphene oxide) aerogel (S/AC/GA) cathode architecture. The AC/GA composite with a well-defined interconnected conductive network was prepared by a reduction-induced self-assembly process, which allows for obtaining compact and porous structures. During this process, reduced graphene oxide (RGO) was formed, and due to the presence of oxygen-containing functional groups on its surface, it not only improves the electronic conductivity of the cathode but also effectively inhibits the polysulfides dissolution and shuttle. The introduced activated carbon allowed for lateral and vertical connection between individual graphene sheets, completing the formation of a stable three-dimensionally (3D) interconnected graphene framework. Moreover, a high specific surface area and 3D interconnected porous structure efficiently hosts a higher amount of active sulfur material, about 65 wt %. The designed S/AC/GA composite electrodes deliver an initial capacity of 1159 mAh g−1 at 0.1 C and can retain a capacity of 765 mAh g−1 after 100 cycles in potential range from 1 V to 3 V. PMID:29373525

Ultrastable α phase nickel hydroxide as energy storage materials for alkaline secondary batteries

NASA Astrophysics Data System (ADS)

Huang, Haili; Guo, Yinjian; Cheng, Yuanhui

2018-03-01

α Phase nickel hydroxide (α-Ni(OH)2) has higher theoretical capacity than that of commercial β phase Ni(OH)2. But the low stability inhibits its wide application in alkaline rechargeable batteries. Here, we propose a totally new idea to stabilize α phase Ni(OH)2 by introducing large organic molecule into the interlayer spacing together with doping multivalent cobalt into the layered Ni(OH)2 host. Ethylene glycol is served as neutral stabilizer in the interlayer spacing. Nickel is substituted by cobalt to increase the electrostatic attraction between layered Ni(OH)2 host and anion ions in the interlayer spacing. Polyethylene glycol (PEG-200) is utilized to design a three-dimensional network structure. This prepared α-Ni(OH)2-20 exhibits specific capacity as high as 334 mAh g-1and good structural stability even after immersing into strong alkaline zincate solution for 20 days. Ni(OH)2 electrode with a specific capacity of 35 mAh cm-2 is fabricated and used as positive electrode in zinc-nickel single flow batteries, which also shows good cycling stability. This result can provide an important guideline for the rational design and preparation of highly active and stable α phase Ni(OH)2 for alkaline secondary battery.

Exercise capacity and muscle strength and risk of vascular disease and arrhythmia in 1.1 million young Swedish men: cohort study.

PubMed

Andersen, Kasper; Rasmussen, Finn; Held, Claes; Neovius, Martin; Tynelius, Per; Sundström, Johan

2015-09-16

To investigate the associations of exercise capacity and muscle strength in late adolescence with risk of vascular disease and arrhythmia. Cohort study. General population in Sweden. 1.1 million men who participated in mandatory military conscription between 1 August 1972 and 31 December 1995, at a median age of 18.2 years. Participants were followed until 31 December 2010. Associations between exercise capacity and muscle strength with risk of vascular disease and subgroups (ischaemic heart disease, heart failure, stroke, and cardiovascular death) and risk of arrhythmia and subgroups (atrial fibrillation or flutter, bradyarrhythmia, supraventricular tachycardia, and ventricular arrhythmia or sudden cardiac death). Maximum exercise capacity was estimated by the ergometer bicycle test, and muscle strength was measured as handgrip strength by a hand dynamometer. High exercise capacity or muscle strength was deemed as above the median level. During a median follow-up of 26.3 years, 26 088 vascular disease events and 17 312 arrhythmia events were recorded. Exercise capacity was inversely associated with risk of vascular disease and its subgroups. Muscle strength was also inversely associated with vascular disease risk, driven by associations of higher muscle strength with lower risk of heart failure and cardiovascular death. Exercise capacity had a U shaped association with risk of arrhythmia, driven by a direct association with risk of atrial fibrillation and a U shaped association with bradyarrhythmia. Higher muscle strength was associated with lower risk of arrhythmia (specifically, lower risk of bradyarrhythmia and ventricular arrhythmia). The combination of high exercise capacity and high muscle strength was associated with a hazard ratio of 0.67 (95% confidence interval 0.65 to 0.70) for vascular events and 0.92 (0.88 to 0.97) for arrhythmia compared with the combination of low exercise capacity and low muscle strength. Exercise capacity and muscle strength in late adolescence are independently and jointly associated with long term risk of vascular disease and arrhythmia. The health benefit of lower risk of vascular events with higher exercise capacity was not outweighed by higher risk of arrhythmia. © Andersen et al 2015.

An electrochemical and structural study of highly uniform tin oxide nanowires fabricated by a novel, scalable solvoplasma technique as anode material for sodium ion batteries

NASA Astrophysics Data System (ADS)

Mukherjee, Santanu; Schuppert, Nicholas; Bates, Alex; Jasinski, Jacek; Hong, Jong-Eun; Choi, Moon Jong; Park, Sam

2017-04-01

A novel solvoplasma based technique was used to fabricate highly uniform SnO2 nanowires (NWs) for application as an anode in sodium-ion batteries (SIBs). This technique is scalable, rapid, and utilizes a rigorous cleaning process to produce very pure SnO2 NWs with enhanced porosity; which improves sodium-ion hosting and reaction kinetics. The batch of NWs obtained from the plasma process were named the "as-made" sample and after cleaning the "pure" sample. Structural characterization showed that the as-made sample has a K+ ion impurity which is absent in the pure samples. The pure samples have a higher maximum specific capacity, 400.71 mAhg-1, and Coulombic efficiency, 85%, compared to the as-made samples which have a maximum specific capacity of 174.69 mAhg-1 and Coulombic efficiency of 74% upon cycling. A study of the electrochemical impedance spectra showed that the as-made samples have a higher interfacial and diffusion resistance than the pure samples and resistances increased after 50 cycles of cell operation for both samples due to progressive electrode degradation. Specific energy vs specific power plots were employed to analyze the performance of the system with respect to the working conditions.

The Building Blocks of Success: Higher-Level Math for All Students. Achieve Policy Brief

ERIC Educational Resources Information Center

Achieve, Inc., 2008

2008-01-01

High schools may still be anchored to 20th century expectations, but what are the critical guideposts for a 21st century high school education? There are many specific skills and competencies that young people will need to succeed, but more than particular skills, they will need the cognitive capacity to educate themselves throughout their entire…

Description and Preliminary Evaluation of a Program for Improving Chemistry Learning in High School Students

ERIC Educational Resources Information Center

Armbrecht, Jose´ Pen~aranda; Arago´n-Muriel, Alberto; Micolta, Germania

2014-01-01

High school students have had some difficulties in understanding chemistry due to traditional ways of teaching this specific science. It is important to improve teaching methods that increase student motivation, not only to enhance their capacity for understanding, but also to generate a greater level of interest in the study of chemistry for…

Porous carbon derived from Sunflower as a host matrix for ultra-stable lithium-selenium battery.

PubMed

Jia, Min; Niu, Yubin; Mao, Cuiping; Liu, Sangui; Zhang, Yan; Bao, Shu-Juan; Xu, Maowen

2017-03-15

A novel porous carbon material using the spongy tissue of sunflower as raw material is reported for the first time. The obtained porous carbon has an extremely high surface area of 2493.0m 2 g -1 , which is beneficial to focus on encapsulating selenium in it and have an inhibiting effect about diffusion of polyselenides over the charge/discharge processes used as the host matrix for Li-Se battery. The porous carbon/Se composite electrode with 63wt% selenium delivers a high specific capacitance of 319mAhg -1 of the initial capacity, and maintains 290mAhg -1 , representing an extremely high capacity retention of 90.9% after 840 cycles with the rate of 1C. Copyright © 2016. Published by Elsevier Inc.

Nitrogen-doped carbon coated MnO nanopeapods as superior anode materials for lithium ion batteries

NASA Astrophysics Data System (ADS)

Ding, Yu; Chen, Lihui; Pan, Pei; Du, Jun; Fu, Zhengbing; Qin, Caiqin; Wang, Feng

2017-11-01

High performance nitrogen-doped carbon (NC) materials decorated with MnO hybrid (MnO@NC) composites with a nanopeapod appearance were synthesized by with a simple hydrothermal method and insuit-polymeric route. As an anode material for lithium ion batteries (LIBs), the nanopeapod structure of MnO@NC composites with internal void spaces exhibits good rate capability, high conductivity and excellent cycling stability. After 200 cycles, the nanopeapod composites yield a specific capacity of 775.4 mAh g-1 at 100 mA g-1 and a high-rate capacity of 559.7 mAh g-1 at 1000 mA g-1. The proposed synthesis of nanopeapod structure composites with an internal room is an efficient design with excellent electrode materials for rechargeable LIBs.

Electrical, thermal and electrochemical properties of disordered carbon prepared from palygorskite and cane molasses

NASA Astrophysics Data System (ADS)

Alvarez, Edelio Danguillecourt; Laffita, Yodalgis Mosqueda; Montoro, Luciano Andrey; Della Santina Mohallem, Nelcy; Cabrera, Humberto; Pérez, Guillermo Mesa; Frutis, Miguel Aguilar; Cappe, Eduardo Pérez

2017-02-01

We have synthesized and electrochemically tested a carbon sample that was suitable as anode for lithium secondary battery. The synthesis was based on the use of the palygorskite clay as template and sugar cane molasses as carbon source. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, Brunauer-Emmett-Teller (BET) measurements and High Resolution Transmission Electron Microscope (HRTEM) analysis showed that the nanometric carbon material has a highly disordered graphene-like wrinkled structure and large specific surface area (467 m2 g-1). The compositional characterization revealed a 14% of heteroatoms-containing groups (O, H, N, S) doping the as-prepared carbon. Thermophysical measurements revealed the good thermal stability and an acceptable thermal diffusivity (9·10-7 m2 s-1) and conductivity (1.1 W m-1 K-1) of this carbon. The electrical properties showed an electronic conductivity of hole-like carriers of approximately one S/cm in a 173-293 K range. The testing of this material as anodes in a secondary lithium battery displayed a high specific capacity and excellent performance in terms of number of cycles. A high reversible capacity of 356 mA h g-1 was reached.

Facile synthesis of zwitterionic polymer-coated core-shell magnetic nanoparticles for highly specific capture of N-linked glycopeptides

NASA Astrophysics Data System (ADS)

Chen, Yajing; Xiong, Zhichao; Zhang, Lingyi; Zhao, Jiaying; Zhang, Quanqing; Peng, Li; Zhang, Weibing; Ye, Mingliang; Zou, Hanfa

2015-02-01

Highly selective and efficient capture of glycosylated proteins and peptides from complex biological samples is of profound significance for the discovery of disease biomarkers in biological systems. Recently, hydrophilic interaction liquid chromatography (HILIC)-based functional materials have been extensively utilized for glycopeptide enrichment. However, the low amount of immobilized hydrophilic groups on the affinity material has limited its specificity, detection sensitivity and binding capacity in the capture of glycopeptides. Herein, a novel affinity material was synthesized to improve the binding capacity and detection sensitivity for glycopeptides by coating a poly(2-(methacryloyloxy)ethyl)-dimethyl-(3-sulfopropyl) ammonium hydroxide (PMSA) shell onto Fe3O4@SiO2 nanoparticles, taking advantage of reflux-precipitation polymerization for the first time (denoted as Fe3O4@SiO2@PMSA). The thick polymer shell endows the nanoparticles with excellent hydrophilic property and several functional groups on the polymer chains. The resulting Fe3O4@SiO2@PMSA demonstrated an outstanding ability for glycopeptide enrichment with high selectivity, extremely high detection sensitivity (0.1 fmol), large binding capacity (100 mg g-1), high enrichment recovery (above 73.6%) and rapid magnetic separation. Furthermore, in the analysis of real complicated biological samples, 905 unique N-glycosylation sites from 458 N-glycosylated proteins were reliably identified in three replicate analyses of a 65 μg protein sample extracted from mouse liver, showing the great potential of Fe3O4@SiO2@PMSA in the detection and identification of low-abundance N-linked glycopeptides in biological samples.Highly selective and efficient capture of glycosylated proteins and peptides from complex biological samples is of profound significance for the discovery of disease biomarkers in biological systems. Recently, hydrophilic interaction liquid chromatography (HILIC)-based functional materials have been extensively utilized for glycopeptide enrichment. However, the low amount of immobilized hydrophilic groups on the affinity material has limited its specificity, detection sensitivity and binding capacity in the capture of glycopeptides. Herein, a novel affinity material was synthesized to improve the binding capacity and detection sensitivity for glycopeptides by coating a poly(2-(methacryloyloxy)ethyl)-dimethyl-(3-sulfopropyl) ammonium hydroxide (PMSA) shell onto Fe3O4@SiO2 nanoparticles, taking advantage of reflux-precipitation polymerization for the first time (denoted as Fe3O4@SiO2@PMSA). The thick polymer shell endows the nanoparticles with excellent hydrophilic property and several functional groups on the polymer chains. The resulting Fe3O4@SiO2@PMSA demonstrated an outstanding ability for glycopeptide enrichment with high selectivity, extremely high detection sensitivity (0.1 fmol), large binding capacity (100 mg g-1), high enrichment recovery (above 73.6%) and rapid magnetic separation. Furthermore, in the analysis of real complicated biological samples, 905 unique N-glycosylation sites from 458 N-glycosylated proteins were reliably identified in three replicate analyses of a 65 μg protein sample extracted from mouse liver, showing the great potential of Fe3O4@SiO2@PMSA in the detection and identification of low-abundance N-linked glycopeptides in biological samples. Electronic supplementary information (ESI) available. See DOI: 10.1039/c4nr05955g

Spherical Al-substituted ɑ-nickel hydroxide with high tapping density applied in Ni-MH battery

NASA Astrophysics Data System (ADS)

Wu, Xing-Hua; Feng, Qing-Ping; Wang, Man; Huang, Gui-Wen

2016-10-01

Spherical Al-substituted ɑ-Ni(OH)2 with high tapping density are prepared with controlled crystallization method, where the synthesis parameters are previously calculated out according to theoretical analysis. The formation mechanism of Ni(OH)2 particles is analyzed based on theoretical calculation, the optimal conditions for the formation of spherical Al-substituted ɑ-Ni(OH)2 with high tapping density are figured out and a formula indicates the restrictions among main synthesis parameters is derived, which is reference meaningful for the synthesis of commercialized electrode powders. Synthesized by using the calculated parameters, the obtained ɑ-Ni(OH)2 shows uniform spherical morphology, high crystal phase purity and reasonable high tapping density of 1.37 g cm-3, which demonstrates the feasibility of the derived formula. Since the electrical conductivity of the pure Ni(OH)2 is quite low, 5 wt% of CoOOH are coated on the ɑ-Ni(OH)2 surface to improve their electrochemical performances. The synthesized CoOOH coated ɑ-Ni(OH)2 shows relative high specific capacity of 327 mAh g-1 at 0.1 C and acceptable high-rate dischargeability. The simultaneously achieving of high tapping density and high specific capacity in ɑ-Ni(OH)2 makes it own the great potential to be applied in new generation of Ni-MH batteries.

THE BASSET CONTINUOUS PROGRESS HIGH SCHOOL.

ERIC Educational Resources Information Center

EISMAN, EDWARD

A CITIZENS COMMITTEE FROM THE BASSETT UNIFIED SCHOOL DISTRICT FELT THAT A CHILD'S INDIVIDUAL CAPACITIES SHOULD BE DEVELOPED AND HIS SENSE OF INDIVIDUAL RESPONSIBILITY SHOULD BE FOSTERED. SINCE MANY CRITICISMS OF EDUCATION WERE RELATED TO DIFFICULTIES ORGANIZATIONAL IN NATURE, THE COMMITTEE INVESTIGATED SCHOOL ORGANIZATIONS DESIGNED SPECIFICALLY TO…

Silvical characteristics of white ash (Fraxinus americana)

Treesearch

Jonathan W. Wright

1959-01-01

White ash (Fraxinus americana L.) derives its common name from the white under-surface of the leaf; the white effect is created by microscopic papillae with a high light-reflecting capacity. The specific name americana was given to the species because of its range in America.

Blueberry consumption inhibits gastrointestinal tumorigenesis in AOM-treated rats

USDA-ARS?s Scientific Manuscript database

Epidemiological studies show inverse or no association of fruit consumption with relative risk for colorectal cancers. Such studies did not examine specific fruits and in particular, those enriched in polyphenols with high antioxidant capacities. We examined blueberry (BB), a fruit rich in anthocy...

Research Update: Hard carbon with closed pores from pectin-free apple pomace waste for Na-ion batteries

NASA Astrophysics Data System (ADS)

Dou, Xinwei; Geng, Chenxi; Buchholz, Daniel; Passerini, Stefano

2018-04-01

Herein, we report a hard carbon derived from industrial bio-waste, i.e., pectin-free apple pomace. The structural, morphological, and electrochemical properties of the hard carbon are reported. The impact of the bio-waste on the closed porosity is discussed, providing valuable insights into the sodium storage mechanism in hard carbons. Most importantly, the hard carbon delivers good electrochemical performance, high specific capacities of 285 mAh g-1, and a very good capacity retention of 96% after 230 cycles at 0.1 C.

Amorphous Zn₂GeO₄ Nanoparticles as Anodes with High Reversible Capacity and Long Cycling Life for Li-ion Batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yi, Ran; Feng, Jinkui; Lv, Dongping

2013-07-30

Amorphous and crystalline Zn₂GeO₄ nanoparticles were prepared and characterized as anode materials for Li-ion batteries. A higher reversible specific capacity of 1250 mAh/g after 500 cycles and excellent rate capability were obtained for amorphous Zn₂GeO₄ nanoparticles, compared to that of crystalline Zn₂GeO₄ nanoparticles. Small particle size, amorphous phase and incorporation of zinc and oxygen contribute synergetically to the improved performance by effectively mitigating the huge volume variations during lithiation and delithiation process.

The utilization of websites for fundraising by NCI-designated cancer centers: Examining the capacity for dialogic communication with prospective donors.

PubMed

Erwin, Cathleen O; Dias, Ashley M

2016-01-01

The study employs a dialogic public relations framework to explore the utilization of the Internet for fundraising by nonprofit health care organizations-specifically, NCI-designated cancer centers. Cancer centers have been noted for effective websites and for being highly engaged in fundraising, which is characterized as relationship marketing. Results indicate all but one cancer center use websites and social media for fundraising but are limited in capacity for two-way symmetrical dialogue. Results are discussed and recommendations are made for future research.

Simultaneous Measurement of Thermophysical Properties of Tissue-Mimicking Phantoms for High Intensity Focused Ultrasound (HIFU) Exposures

NASA Astrophysics Data System (ADS)

Gao, Jing; You, Jiang; Huang, Zhihong; Cochran, Sandy; Corner, George

2012-03-01

Tissue-mimicking phantoms, including bovine serum albumin phantoms and egg white phantoms, have been developed for, and in laboratory use for, real-time visualization of high intensity focused ultrasound-induced thermal coagulative necrosis since 2001. However, until now, very few data are available concerning their thermophysical properties. In this article, a step-wise transient plane source method has been used to determine the values of thermal conductivity, thermal diffusivity, and specific heat capacity of egg white phantoms with elevated egg white concentrations (0 v/v% to 40 v/v%, by 10 v/v% interval) at room temperature (~20 °C). The measured thermophysical properties were close to previously reported values; the thermal conductivity and thermal diffusivity were linearly proportional to the egg white concentration within the investigation range, while the specific heat capacity decreased as the egg white concentration increased. Taking account of large differences between real experiment and ideal model, data variations within 20 % were accepted.

CO2 capture from humid flue gases and humid atmosphere using a microporous coppersilicate.

PubMed

Datta, Shuvo Jit; Khumnoon, Chutharat; Lee, Zhen Hao; Moon, Won Kyung; Docao, Son; Nguyen, Thanh Huu; Hwang, In Chul; Moon, Dohyun; Oleynikov, Peter; Terasaki, Osamu; Yoon, Kyung Byung

2015-10-16

Capturing CO2 from humid flue gases and atmosphere with porous materials remains costly because prior dehydration of the gases is required. A large number of microporous materials with physical adsorption capacity have been developed as CO2-capturing materials. However, most of them suffer from CO2 sorption capacity reduction or structure decomposition that is caused by co-adsorbed H2O when exposed to humid flue gases and atmosphere. We report a highly stable microporous coppersilicate. It has H2O-specific and CO2-specific adsorption sites but does not have H2O/CO2-sharing sites. Therefore, it readily adsorbs both H2O and CO2 from the humid flue gases and atmosphere, but the adsorbing H2O does not interfere with the adsorption of CO2. It is also highly stable after adsorption of H2O and CO2 because it was synthesized hydrothermally. Copyright © 2015, American Association for the Advancement of Science.

Sponge-like reduced graphene oxide/silicon/carbon nanotube composites for lithium ion batteries

NASA Astrophysics Data System (ADS)

Fang, Menglu; Wang, Zhao; Chen, Xiaojun; Guan, Shiyou

2018-04-01

Three-dimensional sponge-like reduced graphene oxide/silicon/carbon nanotube composites were synthesized by one-step hydrothermal self-assembly using silicon nanoparticles, graphene oxide and amino modified carbon nanotubes to develop high-performance anode materials of lithium ion batteries. Scanning electron microscopy and transmission electron microscopy images show the structure of composites that Silicon nanoparticles are coated with reduced graphene oxide while amino modified carbon nanotubes wrap around the reduced graphene oxide in the composites. When applied to lithium ion battery, these composites exhibit high initial specific capacity of 2552 mA h/g at a current density of 0.05 A/g. In addition, reduced graphene oxide/silicon/carbon nanotube composites also have better cycle stability than bare Silicon nanoparticles electrode with the specific capacity of 1215 mA h/g after 100 cycles. The three-dimension sponge-like structure not only ensures the electrical conductivity but also buffers the huge volume change, which has broad potential application in the field of battery.

Genomic analyses of pneumococci from children with sickle cell disease expose host-specific bacterial adaptations and deficits in current interventions

PubMed Central

Muller, Martha; Obert, Caroline; Burnham, Corinna; Mann, Beth; Li, Yimei; Hayden, Randall T; Pestina, Tamara; Persons, Derek; Camilli, Andrew

2014-01-01

Summary Sickle cell disease (SCD) patients are at high risk of contracting pneumococcal infection. To address this risk, they receive pneumococcal vaccines, and antibiotic prophylaxis and treatment. To assess the impact of SCD and these interventions on pneumococcal genetic architecture, we examined the genomes of over 300 pneumococcal isolates from SCD patients over 20 years. Modern SCD strains retained invasive capacity but shifted away from the serotypes used in vaccines. These strains had specific genetic changes related to antibiotic resistance, capsule biosynthesis, metabolism and metal transport. A murine SCD model coupled with Tn-seq mutagenesis identified 60 non-capsular pneumococcal genes under differential selective pressure in SCD, which correlated with aspects of SCD pathophysiology. Further, virulence determinants in the SCD context were distinct from the general population and protective capacity of potential antigens was lost over time in SCD. This highlights the importance of understanding bacterial pathogenesis in the context of high-risk individuals. PMID:24832453

High-performance solid state supercapacitors assembling graphene interconnected networks in porous silicon electrode by electrochemical methods using 2,6-dihydroxynaphthalen.

PubMed

Romanitan, Cosmin; Varasteanu, Pericle; Mihalache, Iuliana; Culita, Daniela; Somacescu, Simona; Pascu, Razvan; Tanasa, Eugenia; Eremia, Sandra A V; Boldeiu, Adina; Simion, Monica; Radoi, Antonio; Kusko, Mihaela

2018-06-25

The challenge for conformal modification of the ultra-high internal surface of nanoporous silicon was tackled by electrochemical polymerisation of 2,6-dihydroxynaphthalene using cyclic voltammetry or potentiometry and, notably, after the thermal treatment (800 °C, N 2 , 4 h) an assembly of interconnected networks of graphene strongly adhering to nanoporous silicon matrix resulted. Herein we demonstrate the achievement of an easy scalable technology for solid state supercapacitors on silicon, with excellent electrochemical properties. Accordingly, our symmetric supercapacitors (SSC) showed remarkable performance characteristics, comparable to many of the best high-power and/or high-energy carbon-based supercapacitors, their figures of merit matching under battery-like supercapacitor behaviour. Furthermore, the devices displayed high specific capacity values along with enhanced capacity retention even at ultra-high rates for voltage sweep, 5 V/s, or discharge current density, 100 A/g, respectively. The cycling stability tests performed at relatively high discharge current density of 10 A/g indicated good capacity retention, with a superior performance demonstrated for the electrodes obtained under cyclic voltammetry approach, which may be ascribed on the one hand to a better coverage of the porous silicon substrate and, on the other hand, to an improved resilience of the hybrid electrode to pore clogging.

Creativity and working memory capacity in sports: working memory capacity is not a limiting factor in creative decision making amongst skilled performers.

PubMed

Furley, Philip; Memmert, Daniel

2015-01-01

The goal of the study was to investigate the relationship between domain-general working memory capacity and domain-specific creativity amongst experienced soccer players. We administered the automated operation span task in combination with a domain-specific soccer creativity task to a group of 61 experienced soccer players to address the question whether an athlete's domain-specific creativity is restricted by their domain-general cognitive abilities (i.e., working memory capacity). Given that previous studies have either found a positive correlation, a negative correlation, or no correlation between working memory capacity and creativity, we analyzed the data in an exploratory manner by following recent recommendations to report effect-size estimations and their precision in form of 95% confidence intervals. The pattern of results provided evidence that domain-general working memory capacity is not associated with creativity in a soccer-specific creativity task. This pattern of results suggests that future research and theorizing on the role of working memory in everyday creative performance needs to distinguish between different types of creative performance while also taking the role of domain-specific experience into account.

Creativity and working memory capacity in sports: working memory capacity is not a limiting factor in creative decision making amongst skilled performers

PubMed Central

Furley, Philip; Memmert, Daniel

2015-01-01

The goal of the study was to investigate the relationship between domain-general working memory capacity and domain-specific creativity amongst experienced soccer players. We administered the automated operation span task in combination with a domain-specific soccer creativity task to a group of 61 experienced soccer players to address the question whether an athlete’s domain-specific creativity is restricted by their domain-general cognitive abilities (i.e., working memory capacity). Given that previous studies have either found a positive correlation, a negative correlation, or no correlation between working memory capacity and creativity, we analyzed the data in an exploratory manner by following recent recommendations to report effect-size estimations and their precision in form of 95% confidence intervals. The pattern of results provided evidence that domain-general working memory capacity is not associated with creativity in a soccer-specific creativity task. This pattern of results suggests that future research and theorizing on the role of working memory in everyday creative performance needs to distinguish between different types of creative performance while also taking the role of domain-specific experience into account. PMID:25713552

Acid Hydrolysis of Wheat Gluten Induces Formation of New Epitopes but Does Not Enhance Sensitizing Capacity by the Oral Route: A Study in “Gluten Free” Brown Norway Rats

PubMed Central

Kroghsbo, Stine; Andersen, Nanna B.; Rasmussen, Tina F.; Madsen, Charlotte B.

2014-01-01

Background Acid hydrolyzed wheat proteins (HWPs) are used in the food and cosmetic industry as emulsifiers. Cases of severe food allergic reactions caused by HWPs have been reported. Recent data suggest that these reactions are caused by HWPs produced by acid hydrolysis. Objectives To examine the sensitizing capacity of gluten proteins per se when altered by acid or enzymatic hydrolysis relative to unmodified gluten in rats naïve to gluten. Methods High IgE-responder Brown Norway (BN) rats bred on a gluten-free diet were sensitized without the use of adjuvant to three different gluten products (unmodified, acid hydrolyzed and enzymatic hydrolyzed). Rats were sensitized by intraperitoneal (i.p.) immunization three times with 200 µg gluten protein/rat or by oral dosing for 35 days with 0.2, 2 or 20 mg gluten protein/rat/day. Sera were analyzed for specific IgG and IgE and IgG-binding capacity by ELISA. IgE functionality was measured by rat basophilic leukemia (RBL) assay. Results Regardless of the route of dosing, all products had sensitizing capacity. When sensitized i.p., all three gluten products induced a strong IgG1 response in all animals. Acid hydrolyzed gluten induced the highest level of specific IgE but with a low functionality. Orally all three gluten products induced specific IgG1 and IgE but with different dose-response relations. Sensitizing rats i.p. or orally with unmodified or enzymatic hydrolyzed gluten induced specific IgG1 responses with similar binding capacity which was different from that of acid hydrolyzed gluten indicating that acid hydrolysis of gluten proteins induces formation of ‘new’ epitopes. Conclusions In rats not tolerant to gluten acid hydrolysis of gluten enhances the sensitizing capacity by the i.p. but not by the oral route. In addition, acid hydrolysis induces formation of new epitopes. This is in contrast to the enzymatic hydrolyzed gluten having an epitope pattern similar to unmodified gluten. PMID:25207551

Proteomic analysis of HDL from inbred mouse strains implicates APOE associated with HDL in reduced cholesterol efflux capacity via the ABCA1 pathway[S

PubMed Central

Pamir, Nathalie; Hutchins, Patrick; Ronsein, Graziella; Vaisar, Tomas; Reardon, Catherine A.; Getz, Godfrey S.; Lusis, Aldons J.; Heinecke, Jay W.

2016-01-01

Cholesterol efflux capacity associates strongly and negatively with the incidence and prevalence of human CVD. We investigated the relationships of HDL’s size and protein cargo with its cholesterol efflux capacity using APOB-depleted serum and HDLs isolated from five inbred mouse strains with different susceptibilities to atherosclerosis. Like humans, mouse HDL carried >70 proteins linked to lipid metabolism, the acute-phase response, proteinase inhibition, and the immune system. HDL’s content of specific proteins strongly correlated with its size and cholesterol efflux capacity, suggesting that its protein cargo regulates its function. Cholesterol efflux capacity with macrophages strongly and positively correlated with retinol binding protein 4 (RBP4) and PLTP, but not APOA1. In contrast, ABCA1-specific cholesterol efflux correlated strongly with HDL’s content of APOA1, APOC3, and APOD, but not RBP4 and PLTP. Unexpectedly, APOE had a strong negative correlation with ABCA1-specific cholesterol efflux capacity. Moreover, the ABCA1-specific cholesterol efflux capacity of HDL isolated from APOE-deficient mice was significantly greater than that of HDL from wild-type mice. Our observations demonstrate that the HDL-associated APOE regulates HDL’s ABCA1-specific cholesterol efflux capacity. These findings may be clinically relevant because HDL’s APOE content associates with CVD risk and ABCA1 deficiency promotes unregulated cholesterol accumulation in human macrophages. PMID:26673204

Hierarchical porous nickel oxide-carbon nanotubes as advanced pseudocapacitor materials for supercapacitors

NASA Astrophysics Data System (ADS)

Su, Aldwin D.; Zhang, Xiang; Rinaldi, Ali; Nguyen, Son T.; Liu, Huihui; Lei, Zhibin; Lu, Li; Duong, Hai M.

2013-03-01

Hierarchical porous carbon anode and metal oxide cathode are promising for supercapacitor with both high energy density and high power density. This Letter uses NiO and commercial carbon nanotubes (CNTs) as electrode materials for electrochemical capacitors with high energy storage capacities. Experimental results show that the specific capacitance of the electrode materials for 10%, 30% and 50% CNTs are 279, 242 and 112 F/g, respectively in an aqueous 1 M KOH electrolyte at a charge rate of 0.56 A/g. The maximum specific capacitance is 328 F/g at a charge rate of 0.33 A/g.

The Sensory Components of High-Capacity Iconic Memory and Visual Working Memory

PubMed Central

Bradley, Claire; Pearson, Joel

2012-01-01

Early visual memory can be split into two primary components: a high-capacity, short-lived iconic memory followed by a limited-capacity visual working memory that can last many seconds. Whereas a large number of studies have investigated visual working memory for low-level sensory features, much research on iconic memory has used more “high-level” alphanumeric stimuli such as letters or numbers. These two forms of memory are typically examined separately, despite an intrinsic overlap in their characteristics. Here, we used a purely sensory paradigm to examine visual short-term memory for 10 homogeneous items of three different visual features (color, orientation and motion) across a range of durations from 0 to 6 s. We found that the amount of information stored in iconic memory is smaller for motion than for color or orientation. Performance declined exponentially with longer storage durations and reached chance levels after ∼2 s. Further experiments showed that performance for the 10 items at 1 s was contingent on unperturbed attentional resources. In addition, for orientation stimuli, performance was contingent on the location of stimuli in the visual field, especially for short cue delays. Overall, our results suggest a smooth transition between an automatic, high-capacity, feature-specific sensory-iconic memory, and an effortful “lower-capacity” visual working memory. PMID:23055993

Enhanced performance of lithium-sulfur batteries with an ultrathin and lightweight MoS2/carbon nanotube interlayer

NASA Astrophysics Data System (ADS)

Yan, Lingjia; Luo, Nannan; Kong, Weibang; Luo, Shu; Wu, Hengcai; Jiang, Kaili; Li, Qunqing; Fan, Shoushan; Duan, Wenhui; Wang, Jiaping

2018-06-01

Ultrathin and lightweight MoS2/carbon nanotube (CNT) interlayers are developed to effectively trap polysulfides in high-performance lithium-sulfur (Li-S) batteries. The MoS2/CNT interlayer is constructed by loading MoS2 nanosheets onto a cross-stacked CNT film. The CNT film with excellent conductivity and superior mechanical properties provides the Li-S batteries with a uniform conductive network, a supporting skeleton for the MoS2 nanosheets, as well as a physical barrier for the polysulfides. Moreover, chemical interactions and bonding between the MoS2 nanosheets and the polysulfides are evident. The electrode with the MoS2/CNT interlayer delivers an attractive specific capacity of 784 mA h g-1 at a high capacity rate of 10 C. In addition, the electrode demonstrates a high initial capacity of 1237 mA h g-1 and a capacity fade as low as -0.061% per cycle over 500 charge/discharge cycles at 0.2 C. The problem of self-discharge can also be suppressed with the introduction of the MoS2/CNT interlayer. The simple fabrication procedure, which is suitable for commercialization, and the outstanding electrochemical performance of the cells with the MoS2/CNT interlayer demonstrate a great potential for the development of high-performance Li-S batteries.

The presence of high-affinity, low-capacity estradiol-17β binding in rainbow trout scale indicates a possible endocrine route for the regulation of scale resorption

USGS Publications Warehouse

Persson, Petra; Shrimpton, J.M.; McCormick, S.D.; Bjornsson, Bjorn Thrandur

2000-01-01

High-affinity, low-capacity estradiol-17β (E2) binding is present in rainbow trout scale. The Kd and Bmax of the scale E2 binding are similar to those of the liver E2 receptor (Kd is 1.6 ± 0.1 and 1.4 ± 0.1 nM, and Bmax is 9.1 ± 1.2 and 23.1 ± 2.2 fmol x mg protein-1, for scale and liver, respectively), but different from those of the high-affinity, low-capacity E2 binding in plasma (Kd is 4.0 ± 0.4 nM and Bmax is 625.4 ± 63.1 fmol x mg protein-1). The E2 binding in scale was displaced by testosterone, but not by diethylstilbestrol. Hence, the ligand binding specificity is different from that of the previously characterized liver E2 receptor, where E2 is displaced by diethylstilbestrol, but not by testosterone. The putative scale E2 receptor thus appears to bind both E2 and testosterone, and it is proposed that the increased scale resorption observed during sexual maturation in both sexes of several salmonid species may be mediated by this receptor. No high-affinity, low-capacity E2 binding could be detected in rainbow trout gill or skin.

High-performance cobalt carbonate hydroxide nano-dot/NiCo(CO3)(OH)2 electrode for asymmetric supercapacitors

NASA Astrophysics Data System (ADS)

Lee, Damin; Xia, Qi Xun; Yun, Je Moon; Kim, Kwang Ho

2018-03-01

Binder-free mesoporous NiCo(CO3)(OH)2 nanowire arrays were grown using a facile hydrothermal technique. The Co2(CO3)(OH)2 in NiCo(CO3)(OH)2 nanowire arrays was well-decorated as nano-dot scale (a few nanometer). In addition, increasing cobalt content in nickel compound matrix, NiCo(CO3)(OH)2 nanowire arrays were separately uniformly grown without agglomeration on Ni foam, providing a high specific surface area to help electrolyte access and ion transfer. The enticing composition and morphology of the NiCo(CO3)(OH)2 nanowire exhibit a superior specific capacity of 1288.2 mAh g-1 at a current density of 3 A g-1 and excellent cycling stability with the capacity retention of 80.7% after 10,000 cycles. Furthermore, an asymmetric supercapacitor composed of the NiCo(CO3)(OH)2 composite as a positive electrode and the graphene as a negative electrode presented a high energy density of 35.5 W h kg-1 at a power density of 2555.6 W kg-1 and satisfactory cycling stability with 71.3% capacity retention after 10,000 cycles. The great combination of the active nano-dot Co2(CO3)(OH)2 and the individually grown NiCo(CO3)(OH)2 nanowires made it a promising electrode material for asymmetric supercapacitors. A well-developed nanoarchitecture of the nano-dot Co2(CO3)(OH)2 decorated NiCo(CO3)(OH)2 composite could pave the way for an excellent electrode design for high-performance supercapacitors.

Tuning Electrochemical Properties of Li-Rich Layered Oxide Cathodes by Adjusting Co/Ni Ratios and Mechanism Investigation Using in situ X-ray Diffraction and Online Continuous Flow Differential Electrochemical Mass Spectrometry.

PubMed

Shen, ShouYu; Hong, YuHao; Zhu, FuChun; Cao, ZhenMing; Li, YuYang; Ke, FuSheng; Fan, JingJing; Zhou, LiLi; Wu, LiNa; Dai, Peng; Cai, MingZhi; Huang, Ling; Zhou, ZhiYou; Li, JunTao; Wu, QiHui; Sun, ShiGang

2018-04-18

Owing to high specific capacity of ∼250 mA h g -1 , lithium-rich layered oxide cathode materials (Li 1+ x Ni y Co z Mn (3- x-2 y-3 z)/4 O 2 ) have been considered as one of the most promising candidates for the next-generation cathode materials of lithium ion batteries. However, the commercialization of this kind of cathode materials seriously restricted by voltage decay upon cycling though Li-rich materials with high cobalt content have been widely studied and show good capacity. This research successfully suppresses voltage decay upon cycling while maintaining high specific capacity with low Co/Ni ratio in Li-rich cathode materials. Online continuous flow differential electrochemical mass spectrometry (OEMS) and in situ X-ray diffraction (XRD) techniques have been applied to investigate the structure transformation of Li-rich layered oxide materials during charge-discharge process. The results of OEMS revealed that low Co/Ni ratio lithium-rich layered oxide cathode materials released no lattice oxygen at the first charge process, which will lead to the suppression of the voltage decay upon cycling. The in situ XRD results displayed the structure transition of lithium-rich layered oxide cathode materials during the charge-discharge process. The Li 1.13 Ni 0.275 Mn 0.580 O 2 cathode material exhibited a high initial medium discharge voltage of 3.710 and a 3.586 V medium discharge voltage with the lower voltage decay of 0.124 V after 100 cycles.

Materials Challenges and Opportunities of Lithium-ion Batteries for Electrical Energy Storage

NASA Astrophysics Data System (ADS)

Manthiram, Arumugam

2011-03-01

Electrical energy storage has emerged as a topic of national and global importance with respect to establishing a cleaner environment and reducing the dependence on foreign oil. Batteries are the prime candidates for electrical energy storage. They are the most viable near-term option for vehicle applications and the efficient utilization of intermittent energy sources like solar and wind. Lithium-ion batteries are attractive for these applications as they offer much higher energy density than other rechargeable battery systems. However, the adoption of lithium-ion battery technology for vehicle and stationary storage applications is hampered by high cost, safety concerns, and limitations in energy, power, and cycle life, which are in turn linked to severe materials challenges. This presentation, after providing an overview of the current status, will focus on the physics and chemistry of new materials that can address these challenges. Specifically, it will focus on the design and development of (i) high-capacity, high-voltage layered oxide cathodes, (ii) high-voltage, high-power spinel oxide cathodes, (iii) high-capacity silicate cathodes, and (iv) nano-engineered, high-capacity alloy anodes. With high-voltage cathodes, a critical issue is the instability of the electrolyte in contact with the highly oxidized cathode surface and the formation of solid-electrolyte interfacial (SEI) layers that degrade the performance. Accordingly, surface modification of cathodes with nanostructured materials and self-surface segregation during the synthesis process to suppress SEI layer formation and enhance the energy, power, and cycle life will be emphasized. With the high-capacity alloy anodes, a critical issue is the huge volume change occurring during the charge-discharge process and the consequent poor cycle life. Dispersion of the active alloy nanoparticles in an inactive metal oxide-carbon matrix to mitigate this problem and realize long cycle life will be presented.

Interlayer-Spacing-Regulated VOPO4 Nanosheets with Fast Kinetics for High-Capacity and Durable Rechargeable Magnesium Batteries.

PubMed

Zhou, Limin; Liu, Qi; Zhang, Zihe; Zhang, Kai; Xiong, Fangyu; Tan, Shuangshuang; An, Qinyou; Kang, Yong-Mook; Zhou, Zhen; Mai, Liqiang

2018-06-25

Owing to the low-cost, safety, dendrite-free formation, and two-electron redox properties of magnesium (Mg), rechargeable Mg batteries are considered as promising next-generation secondary batteries with high specific capacity and energy density. However, the clumsy Mg 2+ with high polarity inclines to sluggish Mg insertion/deinsertion, leading to inadequate reversible capacity and rate performance. Herein, 2D VOPO 4 nanosheets with expanded interlayer spacing (1.42 nm) are prepared and applied in rechargeable magnesium batteries for the first time. The interlayer expansion provides enough diffusion space for fast kinetics of MgCl + ion flux with low polarization. Benefiting from the structural configuration, the Mg battery exhibits a remarkable reversible capacity of 310 mAh g -1 at 50 mA g -1 , excellent rate capability, and good cycling stability (192 mAh g -1 at 100 mA g -1 even after 500 cycles). In addition, density functional theory (DFT) computations are conducted to understand the electrode behavior with decreased MgCl + migration energy barrier compared with Mg 2+ . This approach, based on the regulation of interlayer distance to control cation insertion, represents a promising guideline for electrode material design on the development of advanced secondary multivalent-ion batteries. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Three-Dimensional LiMnPO4·Li3V2(PO4)3/C Nanocomposite as a Bicontinuous Cathode for High-Rate and Long-Life Lithium-Ion Batteries.

PubMed

Luo, Yanzhu; Xu, Xu; Zhang, Yuxiang; Pi, Yuqiang; Yan, Mengyu; Wei, Qiulong; Tian, Xiaocong; Mai, Liqiang

2015-08-12

Olivine-type LiMnPO4 has been extensively studied as a high-energy density cathode material for lithium-ion batteries. To improve both the ionic and electronic conductivities of LiMnPO4, a series of carbon-decorated LiMnPO4·Li3V2(PO4)3 nanocomposites are synthesized by a facile sol-gel method combined with the conventional solid-state method. The optimized composite presents a three-dimensional hierarchical structure with active nanoparticles well-embedded in a conductive carbon matrix. The combination of the nanoscale carbon coating and the microscale carbon network could provide a more active site for electrochemical reaction, as well as a highly conductive network for both electron and lithium-ion transportation. When cycled at 20 C, an initial specific capacity of 103 mA h g(-1) can be obtained and the capacity retention reaches 68% after 3000 cycles, corresponding to a capacity fading of 0.013% per cycle. The stable capacity and excellent rate capability make this carbon-decorated LiMnPO4·Li3V2(PO4)3 nanocomposite a promising cathode for lithium-ion batteries.

Scalable and sustainable synthesis of carbon microspheres via a purification-free strategy for sodium-ion capacitors

NASA Astrophysics Data System (ADS)

Wang, Shijie; Wang, Rutao; Zhang, Yabin; Jin, Dongdong; Zhang, Li

2018-03-01

Sodium-based energy storage receives a great deal of interest due to the virtually inexhaustible sodium reserve, while the scalable and sustainable strategies to synthesize carbon-based materials with suitable interlayer spaces and large sodium storage capacities are yet to be fully investigated. Carbon microspheres, with regular geometry, non-graphitic characteristic, and stable nature are promising candidates, yet the synthetic methods are usually complex and energy consuming. In this regard, we report a scalable purification-free strategy to synthesize carbon microspheres directly from 5 species of fresh juice. As-synthesized carbon microspheres exhibit dilated interlayer distance of 0.375 nm and facilitate Na+ uptake and release. For example, such carbon microsphere anodes have a specific capacity of 183.9 mAh g-1 at 50 mA g-1 and exhibit ultra-stability (99.0% capacity retention) after 10000 cycles. Moreover, via facile activation, highly porous carbon microsphere cathodes are fabricated and show much higher energy density at high rate than commercial activated carbon. Coupling the compelling anodes and cathodes above, novel sodium-ion capacitors show the high working potential up to 4.0 V, deliver a maximum energy density of 52.2 Wh kg-1, and exhibit an acceptable capacity retention of 85.7% after 2000 cycles.

Final Scientific/Technical Report for Low Cost, High Capacity Non- Intercalation Chemistry Automotive Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Berdichevsky, Gene

Commercial Li-ion batteries typically use Ni- and Co-based intercalation cathodes. As the demand for improved performance from batteries increases, these cathode materials will no longer be able to provide the desired energy storage characteristics since they are currently approaching their theoretical limits. Conversion cathode materials are prime candidates for improvement of Li-ion batteries. On both a volumetric and gravimetric basis they have higher theoretical capacity than intercalation cathode materials. Metal fluoride (MFx) cathodes offer higher specific energy density and dramatically higher volumetric energy density. Challenges associated with metal fluoride cathodes were addressed through nanostructured material design and synthesis. A majormore » goal of this project was to develop and demonstrate Li-ion cells based on Si-comprising anodes and metal fluoride (MFx) comprising cathodes. Pairing the high-capacity MFx cathode with a high-capacity anode, such as an alloying Si anode, allows for the highest possible energy density on a cell level. After facing and overcoming multiple material synthesis and electrochemical instability challenges, we succeeded in fabrication of MFx half cells with cycle stability in excess of 500 cycles (to 20% or smaller degradation) and full cells with MFx-based cathodes and Si-based anodes with cycle stability in excess of 200 cycles (to 20% or smaller degradation).« less

A shared, flexible neural map architecture reflects capacity limits in both visual short-term memory and enumeration.

PubMed

Knops, André; Piazza, Manuela; Sengupta, Rakesh; Eger, Evelyn; Melcher, David

2014-07-23

Human cognition is characterized by severe capacity limits: we can accurately track, enumerate, or hold in mind only a small number of items at a time. It remains debated whether capacity limitations across tasks are determined by a common system. Here we measure brain activation of adult subjects performing either a visual short-term memory (vSTM) task consisting of holding in mind precise information about the orientation and position of a variable number of items, or an enumeration task consisting of assessing the number of items in those sets. We show that task-specific capacity limits (three to four items in enumeration and two to three in vSTM) are neurally reflected in the activity of the posterior parietal cortex (PPC): an identical set of voxels in this region, commonly activated during the two tasks, changed its overall response profile reflecting task-specific capacity limitations. These results, replicated in a second experiment, were further supported by multivariate pattern analysis in which we could decode the number of items presented over a larger range during enumeration than during vSTM. Finally, we simulated our results with a computational model of PPC using a saliency map architecture in which the level of mutual inhibition between nodes gives rise to capacity limitations and reflects the task-dependent precision with which objects need to be encoded (high precision for vSTM, lower precision for enumeration). Together, our work supports the existence of a common, flexible system underlying capacity limits across tasks in PPC that may take the form of a saliency map. Copyright © 2014 the authors 0270-6474/14/349857-10$15.00/0.

Draft environmental impact statement siting, construction, and operation of New Production Reactor capacity. Volume 4, Appendices D-R

DOE Office of Scientific and Technical Information (OSTI.GOV)

None

1991-04-01

This Environmental Impact Statement (EIS) assesses the potential environmental impacts, both on a broad programmatic level and on a project-specific level, concerning a proposed action to provide new tritium production capacity to meet the nation`s nuclear defense requirements well into the 21st century. A capacity equivalent to that of about a 3,000-megawatt (thermal) heavy-water reactor was assumed as a reference basis for analysis in this EIS; this is the approximate capacity of the existing production reactors at DOE`s Savannah River Site near Aiken, South Carolina. The EIS programmatic alternatives address Departmental decisions to be made on whether to build newmore » production facilities, whether to build one or more complexes, what size production capacity to provide, and when to provide this capacity. Project-specific impacts for siting, constructing, and operating new production reactor capacity are assessed for three alternative sites: the Hanford Site near Richland, Washington; the Idaho National Engineering Laboratory near Idaho Falls, Idaho; and the Savannah River Site. For each site, the impacts of three reactor technologies (and supporting facilities) are assessed: a heavy-water reactor, a light-water reactor, and a modular high-temperature gas-cooled reactor. Impacts of the no-action alternative also are assessed. The EIS evaluates impacts related to air quality; noise levels; surface water, groundwater, and wetlands; land use; recreation; visual environment; biotic resources; historical, archaeological, and cultural resources; socioeconomics; transportation; waste management; and human health and safety. The EIS describes in detail the potential radioactive releases from new production reactors and support facilities and assesses the potential doses to workers and the general public. This volume contains 15 appendices.« less

Simulation model for port shunting yards

NASA Astrophysics Data System (ADS)

Rusca, A.; Popa, M.; Rosca, E.; Rosca, M.; Dragu, V.; Rusca, F.

2016-08-01

Sea ports are important nodes in the supply chain, joining two high capacity transport modes: rail and maritime transport. The huge cargo flows transiting port requires high capacity construction and installation such as berths, large capacity cranes, respectively shunting yards. However, the port shunting yards specificity raises several problems such as: limited access since these are terminus stations for rail network, the in-output of large transit flows of cargo relatively to the scarcity of the departure/arrival of a ship, as well as limited land availability for implementing solutions to serve these flows. It is necessary to identify technological solutions that lead to an answer to these problems. The paper proposed a simulation model developed with ARENA computer simulation software suitable for shunting yards which serve sea ports with access to the rail network. Are investigates the principal aspects of shunting yards and adequate measures to increase their transit capacity. The operation capacity for shunting yards sub-system is assessed taking in consideration the required operating standards and the measure of performance (e.g. waiting time for freight wagons, number of railway line in station, storage area, etc.) of the railway station are computed. The conclusion and results, drawn from simulation, help transports and logistics specialists to test the proposals for improving the port management.

Facile synthesis and electrochemical performance of the nanoscaled FePy anode

NASA Astrophysics Data System (ADS)

Wang, Guixin; Zhang, Ruibo; Jiang, Tianchan; Chernova, Natasha A.; Dong, Zhixin; Whittingham, M. Stanley

2014-12-01

Fe-P alloys with high phosphorous content have been targeted as promising anode materials because of their high theoretical capacity. However, the synthesis and cycling performance remain great challenges. Hereby FePy (3 ≤ y ≤ 4) nanoparticles are facilely synthesized through a dry mechanochemical method by reacting iron and red phosphorus powders in an inert atmosphere. The morphology and crystal structure of this material are characterized by SEM and XRD, respectively, while the electrochemical performance is evaluated by a number of different techniques. The 1st and 2nd discharge capacity of FePy reaches 1984 mAh g-1 and 1486 mAh g-1, respectively, and after 10 cycles at 0.03 mA cm-2 (20 mA g-1, 0.03C), the capacity remains 1089 mAh g-1 with a coulombic efficiency of 97%, much higher than the reported results to date. The cyclability of this material becomes fairly better at a higher current density, but the specific capacity is lower compared to that of the smaller current density. By adding fluoroethylene carbonate (FEC) to the electrolyte, the cycling performance of this material was improved. The EIS analysis has also been performed in order to better understand the capacity fade mechanism of FePy.

High Areal Capacity Si/LiCoO 2 Batteries from Electrospun Composite Fiber Mats

DOE Office of Scientific and Technical Information (OSTI.GOV)

Self, Ethan C.; Naguib, Michael; Ruther, Rose E.

Here, freestanding nanofiber mat Li-ion battery anodes containing Si nanoparticles, carbon black, and poly(acrylic acid) (Si/C/PAA) are prepared using electrospinning. The mats are compacted to a high fiber volume fraction (~0.85), and interfiber contacts are welded by exposing the mat to methanol vapor. A compacted+welded fiber mat anode containing 40 wt % Si exhibits high capacities of 1,484 mA h g -1 (3,500 mA h gmore » $$-1\\atop{Si}$$) at 0.1 C and 489 mAh g -1 at 1 C and good cycling stability (e.g., 73% capacity retention over 50 cycles). Post-mortem analysis of the fiber mats shows that the overall electrode structure is preserved during cycling. Whereas many nanostructured Si anodes are hindered by their low active material loadings and densities, thick, densely packed Si/C/PAA fiber mat anodes reported here have high areal and volumetric capacities (e.g., 4.5 mA h cm -2 and 750 mA h cm -3, respectively). A full cell containing an electrospun Si/C/PAA anode and electrospun LiCoO 2-based cathode has a high specific energy density of 270 Wh kg -1. The excellent performance of the electrospun Si/C/PAA fiber mat anodes is attributed to the: (i) PAA binder which interacts with the SiO x surface of Si nanoparticles and (ii) high material loading, high fiber volume fraction, and welded interfiber contacts of the electrospun mats« less

High Areal Capacity Si/LiCoO 2 Batteries from Electrospun Composite Fiber Mats

DOE PAGES

Self, Ethan C.; Naguib, Michael; Ruther, Rose E.; ...

2017-03-24

Here, freestanding nanofiber mat Li-ion battery anodes containing Si nanoparticles, carbon black, and poly(acrylic acid) (Si/C/PAA) are prepared using electrospinning. The mats are compacted to a high fiber volume fraction (~0.85), and interfiber contacts are welded by exposing the mat to methanol vapor. A compacted+welded fiber mat anode containing 40 wt % Si exhibits high capacities of 1,484 mA h g -1 (3,500 mA h gmore » $$-1\\atop{Si}$$) at 0.1 C and 489 mAh g -1 at 1 C and good cycling stability (e.g., 73% capacity retention over 50 cycles). Post-mortem analysis of the fiber mats shows that the overall electrode structure is preserved during cycling. Whereas many nanostructured Si anodes are hindered by their low active material loadings and densities, thick, densely packed Si/C/PAA fiber mat anodes reported here have high areal and volumetric capacities (e.g., 4.5 mA h cm -2 and 750 mA h cm -3, respectively). A full cell containing an electrospun Si/C/PAA anode and electrospun LiCoO 2-based cathode has a high specific energy density of 270 Wh kg -1. The excellent performance of the electrospun Si/C/PAA fiber mat anodes is attributed to the: (i) PAA binder which interacts with the SiO x surface of Si nanoparticles and (ii) high material loading, high fiber volume fraction, and welded interfiber contacts of the electrospun mats« less

Transforming from planar to three-dimensional lithium with flowable interphase for solid lithium metal batteries

PubMed Central

Liu, Yayuan; Lin, Dingchang; Jin, Yang; Liu, Kai; Tao, Xinyong; Zhang, Qiuhong; Zhang, Xiaokun; Cui, Yi

2017-01-01

Solid-state lithium (Li) metal batteries are prominent among next-generation energy storage technologies due to their significantly high energy density and reduced safety risks. Previously, solid electrolytes have been intensively studied and several materials with high ionic conductivity have been identified. However, there are still at least three obstacles before making the Li metal foil-based solid-state systems viable, namely, high interfacial resistance at the Li/electrolyte interface, low areal capacity, and poor power output. The problems are addressed by incorporating a flowable interfacial layer and three-dimensional Li into the system. The flowable interfacial layer can accommodate the interfacial fluctuation and guarantee excellent adhesion at all time, whereas the three-dimensional Li significantly reduces the interfacial fluctuation from the whole electrode level (tens of micrometers) to local scale (submicrometer) and also decreases the effective current density for high-capacity and high-power operations. As a consequence, both symmetric and full-cell configurations can achieve greatly improved electrochemical performances in comparison to the conventional Li foil, which are among the best reported values in the literature. Noticeably, solid-state full cells paired with high–mass loading LiFePO4 exhibited, at 80°C, a satisfactory specific capacity even at a rate of 5 C (110 mA·hour g−1) and a capacity retention of 93.6% after 300 cycles at a current density of 3 mA cm−2 using a composite solid electrolyte middle layer. In addition, when a ceramic electrolyte middle layer was adopted, stable cycling with greatly improved capacity could even be realized at room temperature. PMID:29062894

Transforming from planar to three-dimensional lithium with flowable interphase for solid lithium metal batteries

DOE Office of Scientific and Technical Information (OSTI.GOV)

Liu, Yayuan; Lin, Dingchang; Jin, Yang

Solid-state lithium (Li) metal batteries are prominent among next-generation energy storage technologies due to their significantly high energy density and reduced safety risks. Previously, solid electrolytes have been intensively studied and several materials with high ionic conductivity have been identified. However, there are still at least three obstacles before making the Li metal foil-based solid-state systems viable, namely, high interfacial resistance at the Li/electrolyte interface, low areal capacity, and poor power output. The problems are addressed by incorporating a flowable interfacial layer and three-dimensional Li into the system. The flowable interfacial layer can accommodate the interfacial fluctuation and guarantee excellentmore » adhesion at all time, whereas the three-dimensional Li significantly reduces the interfacial fluctuation from the whole electrode level (tens of micrometers) to local scale (submicrometer) and also decreases the effective current density for high-capacity and high-power operations. As a consequence, both symmetric and full-cell configurations can achieve greatly improved electrochemical performances in comparison to the conventional Li foil, which are among the best reported values in the literature. Noticeably, solid-state full cells paired with high–mass loading LiFePO4 exhibited, at 80°C, a satisfactory specific capacity even at a rate of 5 C (110 mA·hour g -1) and a capacity retention of 93.6% after 300 cycles at a current density of 3 mA cm -2 using a composite solid electrolyte middle layer. In addition, when a ceramic electrolyte middle layer was adopted, stable cycling with greatly improved capacity could even be realized at room temperature.« less

Transforming from planar to three-dimensional lithium with flowable interphase for solid lithium metal batteries

DOE PAGES

Liu, Yayuan; Lin, Dingchang; Jin, Yang; ...

2017-10-01

Solid-state lithium (Li) metal batteries are prominent among next-generation energy storage technologies due to their significantly high energy density and reduced safety risks. Previously, solid electrolytes have been intensively studied and several materials with high ionic conductivity have been identified. However, there are still at least three obstacles before making the Li metal foil-based solid-state systems viable, namely, high interfacial resistance at the Li/electrolyte interface, low areal capacity, and poor power output. The problems are addressed by incorporating a flowable interfacial layer and three-dimensional Li into the system. The flowable interfacial layer can accommodate the interfacial fluctuation and guarantee excellentmore » adhesion at all time, whereas the three-dimensional Li significantly reduces the interfacial fluctuation from the whole electrode level (tens of micrometers) to local scale (submicrometer) and also decreases the effective current density for high-capacity and high-power operations. As a consequence, both symmetric and full-cell configurations can achieve greatly improved electrochemical performances in comparison to the conventional Li foil, which are among the best reported values in the literature. Noticeably, solid-state full cells paired with high–mass loading LiFePO4 exhibited, at 80°C, a satisfactory specific capacity even at a rate of 5 C (110 mA·hour g -1) and a capacity retention of 93.6% after 300 cycles at a current density of 3 mA cm -2 using a composite solid electrolyte middle layer. In addition, when a ceramic electrolyte middle layer was adopted, stable cycling with greatly improved capacity could even be realized at room temperature.« less

The Elevated Susceptibility to Diabetes in India: An Evolutionary Perspective

PubMed Central

Wells, Jonathan C. K.; Pomeroy, Emma; Walimbe, Subhash R.; Popkin, Barry M.; Yajnik, Chittaranjan S.

2016-01-01

India has rapidly become a “diabetes capital” of the world, despite maintaining high rates of under-nutrition. Indians develop diabetes at younger age and at lower body weights than other populations. Here, we interpret these characteristics in terms of a “capacity–load” model of glucose homeostasis. Specifically, we assume that glycemic control depends on whether the body’s “metabolic capacity,” referring to traits, such as pancreatic insulin production and muscle glucose clearance, is able to resolve the “metabolic load” generated by high levels of body fat, high dietary glycemic load, and sedentary behavior. We employ data from modern cohorts to support the model and the interpretation that elevated diabetic risk among Indian populations results from the high metabolic load imposed by westernized lifestyles acting on a baseline of low metabolic capacity. We attribute this low metabolic capacity to the low birth weight characteristic of Indian populations, which is associated with short stature and low lean mass in adult life. Using stature as a marker of metabolic capacity, we review archeological and historical evidence to highlight long-term declines in Indian stature associated with adaptation to several ecological stresses. Underlying causes may include increasing population density following the emergence of agriculture, the spread of vegetarian diets, regular famines induced by monsoon failure, and the undermining of agricultural security during the colonial period. The reduced growth and thin physique that characterize Indian populations elevate susceptibility to truncal obesity, and increase the metabolic penalties arising from sedentary behavior and high glycemic diets. Improving metabolic capacity may require multiple generations; in the meantime, efforts to reduce the metabolic load will help ameliorate the situation. PMID:27458578

Temporal Context Memory in High-Functioning Autism

ERIC Educational Resources Information Center

Gras-Vincendon, Agnes; Mottron, Laurent; Salame, Pierre; Bursztejn, Claude; Danion, Jean-Marie

2007-01-01

Episodic memory, i.e. memory for specific episodes situated in space and time, seems impaired in individuals with autism. According to weak central coherence theory, individuals with autism have general difficulty connecting contextual and item information which then impairs their capacity to memorize information in context. This study…

Biomass derived nitrogen-doped hierarchical porous carbon sheets for supercapacitors with high performance.

PubMed

Wang, Cunjing; Wu, Dapeng; Wang, Hongju; Gao, Zhiyong; Xu, Fang; Jiang, Kai

2018-08-01

A facile potassium chloride salt-locking technique combined with hydrothermal treatment on precursors was explored to prepare nitrogen-doped hierarchical porous carbon sheets in air from biomass. Benefiting from the effective synthesis strategy, the as-obtained carbon possesses a unique nitrogen-doped thin carbon sheet structure with abundant hierarchical pores and large specific surface areas of 1459 m 2  g -1 . The doped nitrogen in carbon framework has a positive effect on the electrochemical properties of the electrode material, the thin carbon sheet structure benefits for fast ion transfer, the abundant meso-pores provide convenient channels for rapid charge transportation, large specific surface area and lots of micro-pores guarantee sufficient ion-storage sites. Therefore, applied for supercapacitors, the carbon electrode material exhibits an outstanding specific capacitance of 451 F g -1 at 0.5 A g -1 in a three-electrode system. Moreover, the assembled symmetric supercapacitor based on two identical carbon electrodes also displays high specific capacitance of 309 F g -1 at 0.5 A g -1 , excellent rate capacity and remarkable cycling stability with 99.3% of the initial capacitance retention after 10,000 cycles at 5 A -1 . The synthesis strategy avoids expensive inert gas protection and the use of corrosive KOH and toxic ZnCl 2 activated reagents, representing a promising green route to design advanced carbon electrode materials from biomass for high-capacity supercapacitors. Copyright © 2018. Published by Elsevier Inc.

Iron Oxide Nanosheets and Pulse-Electrodeposited Ni-Co-S Nanoflake Arrays for High-Performance Charge Storage.

PubMed

Khani, Hadi; Wipf, David O

2017-03-01

Nanostructured nickel cobalt sulfide (Ni 4.5 Co 4.5 S 8 ) has been prepared through a single-step pulse-electrodeposition method. Iron oxide nanosheets at hollow graphite shells (Fe 3 O 4 @g-shells) were prepared from graphite-coated iron carbide/α-Fe (g-Fe 3 C/Fe) in a two-step annealing/electrochemical cycling process. Electrochemical characterization of the Ni 4.5 Co 4.5 S 8 and g-Fe 3 C/Fe materials showed that both have high specific capacities (206 mAh g -1 and 147 mAh g -1 at 1 A g -1 ) and excellent rate capabilities (∼95% and ∼83% retention at 20 A g -1 , respectively). To demonstrate the advantageous pairing of these high rate materials, a full-cell battery with supercapacitor-like power behavior was assembled with Ni 4.5 Co 4.5 S 8 and g-Fe 3 C/Fe as the positive and negative electrodes, respectively. The (Ni 4.5 Co 4.5 S 8 //g-Fe 3 C/Fe) device could be reversibly operated in a 0.0-1.6 V potential window, delivering an impressive specific energy of 89 Wh kg -1 at 1.1 kW kg -1 and a remarkable rate performance of 61 Wh kg -1 at a very high specific power of 38.5 kW kg -1 . Additionally, long-term cycling demonstrated that the asymmetric full cell assembly retained 91% of its initial specific capacity after 2500 cycles at 40 A g -1 . The performance features of this device are among the best for iron oxide/hydroxide and bimetallic sulfide based energy storage devices to date, thereby giving insight into design principles for the next generation high-energy-density devices.

Glucose-assisted synthesis of Na3V2(PO4)3/C composite as an electrode material for high-performance sodium-ion batteries

NASA Astrophysics Data System (ADS)

Li, Guangqiang; Jiang, Danlu; Wang, Hui; Lan, Xinzheng; Zhong, Honghai; Jiang, Yang

2014-11-01

A novel electrode material for sodium-ion batteries (NIBs), Na3V2(PO4)3 with a rhombohedral, Na+ superionic conductor (NASICON)-type structure, was synthesised via a solid-state carbon-thermal reduction reaction assisted by mechanochemical activation. Electron microscopy analysis showed that the synthesised Na3V2(PO4)3 particles had an average size of 300 nm, being coated with a uniform layer of carbon 3 nm in thickness. As a cathode material, Na3V2(PO4)3/C exhibited an initial specific discharge capacity of 98.17 mAh g-1 at 0.1C for potentials ranging from 2.5 to 3.8 V. This was owing to the V3+/V4+ redox couple, which corresponded to the two-phase transition between Na3V2(PO4)3 and NaV2(PO4)3. The cathode lost 4.92% of its discharge specific capacity after 50 cycles. As an anode material, Na3V2(PO4)3/C exhibited an initial specific discharge capacity of 63.2 mAh g-1 at 0.1C for potentials ranging from 1.0 to 2.5 V. This was owing to the V2+/V3+ redox couple, which corresponded to the two-phase transition between Na3V2(PO4)3 and Na4V2(PO4)3. The anode lost approximately 5.41% of its discharge specific capacity after 50 cycles. The three-dimensional channel structure of NaV2(PO4)3 and the changes induced in its lattice parameters during the charge/discharge processes were simulated on the basis of density functional theory.

Graphene-Selenium Hybrid Microballs as Cathode Materials for High-performance Lithium-Selenium Secondary Battery Applications.

PubMed

Youn, Hee-Chang; Jeong, Jun Hui; Roh, Kwang Chul; Kim, Kwang-Bum

2016-08-02

In this study, graphene-selenium hybrid microballs (G-SeHMs) are prepared in one step by aerosol microdroplet drying using a commercial spray dryer, which represents a simple, scalable continuous process, and the potential of the G-SeHMs thus prepared is investigated for use as cathode material in applications of lithium-selenium secondary batteries. These morphologically unique graphene microballs filled with Se particles exhibited good electrochemical properties, such as high initial specific capacity (642 mA h g(-1) at 0.1 C, corresponding to Se electrochemical utilisation as high as 95.1%), good cycling stability (544 mA h g(-1) after 100 cycles at 0.1 C; 84.5% retention) and high rate capability (specific capacity of 301 mA h g(-1) at 5 C). These electrochemical properties are attributed to the fact that the G-SeHM structure acts as a confinement matrix for suppressing the dissolution of polyselenides in the organic electrolyte, as well as an electron conduction path for increasing the transport rate of electrons for electrochemical reactions. Notably, based on the weight of hybrid materials, electrochemical performance is considerably better than that of previously reported Se-based cathode materials, attributed to the high Se loading content (80 wt%) in hybrid materials.

Mesoporous carbon spheres with controlled porosity for high-performance lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Wang, Dexian; Fu, Aiping; Li, Hongliang; Wang, Yiqian; Guo, Peizhi; Liu, Jingquan; Zhao, Xiu Song

2015-07-01

Mesoporous carbon (MC) spheres with hierarchical pores, controlled pore volume and high specific surface areas have been prepared by a mass-producible spray drying assisted template method using sodium alginate as carbon precursor and commercial colloidal silica particles as hard template. The resulting MC spheres, possessing hierarchical pores in the range of 3-30 nm, are employed as conductive matrices for the preparation of cathode materials for lithium-sulfur batteries. A high pressure induced one-step impregnation of elemental sulfur into the pore of the MC spheres has been exploited. The electrochemical performances of sulfur-impregnated MC spheres (S-MC) derived from MC spheres with different pore volume and specific surface area but with the same sulfur loading ratio of 60 wt% (S-MC-X-60) have been investigated in details. The S-MC-4-60 composite cathode material displayed a high initial discharge capacity of 1388 mAhg-1 and a good cycling stability of 857 mAhg-1 after 100 cycles at 0.2C, and shows also excellent rate capability of 864 mAhg-1 at 2C. More importantly, the sulfur loading content in MC-4 spheres can reach as high as 80%, and it still can deliver a capacity of 569 mAhg-1 after 100 cycles at 0.2C.

Bore-sight calibration of the profile laser scanner using a large size exterior calibration field

NASA Astrophysics Data System (ADS)

Koska, Bronislav; Křemen, Tomáš; Štroner, Martin

2014-10-01

The bore-sight calibration procedure and results of a profile laser scanner using a large size exterior calibration field is presented in the paper. The task is a part of Autonomous Mapping Airship (AMA) project which aims to create s surveying system with specific properties suitable for effective surveying of medium-wide areas (units to tens of square kilometers per a day). As is obvious from the project name an airship is used as a carrier. This vehicle has some specific properties. The most important properties are high carrying capacity (15 kg), long flight time (3 hours), high operating safety and special flight characteristics such as stability of flight, in terms of vibrations, and possibility to flight at low speed. The high carrying capacity enables using of high quality sensors like professional infrared (IR) camera FLIR SC645, high-end visible spectrum (VIS) digital camera and optics in the visible spectrum and tactical grade INSGPS sensor iMAR iTracerRT-F200 and profile laser scanner SICK LD-LRS1000. The calibration method is based on direct laboratory measuring of coordinate offset (lever-arm) and in-flight determination of rotation offsets (bore-sights). The bore-sight determination is based on the minimization of squares of individual point distances from measured planar surfaces.

Methods and Apparatuses for Signaling with Geometric Constellations

NASA Technical Reports Server (NTRS)

Barsoum, Maged F. (Inventor); Jones, Christopher R. (Inventor)

2018-01-01

Communication systems are described that use signal constellations, which have unequally spaced (i.e. `geometrically` shaped) points. In many embodiments, the communication systems use specific geometric constellations that are capacity optimized at a specific SNR. In addition, ranges within which the constellation points of a capacity optimized constellation can be perturbed and are still likely to achieve a given percentage of the optimal capacity increase compared to a constellation that maximizes d.sub.min, are also described. Capacity measures that are used in the selection of the location of constellation points include, but are not limited to, parallel decode (PD) capacity and joint capacity.

Methods and apparatuses for signaling with geometric constellations

NASA Technical Reports Server (NTRS)

Jones, Christopher R. (Inventor); Barsoum, Maged F. (Inventor)

2012-01-01

Communication systems are described that use signal constellations, which have unequally spaced (i.e. geometrically shaped) points. In many embodiments, the communication systems use specific geometric constellations that are capacity optimized at a specific SNR. In addition, ranges within which the constellation points of a capacity optimized constellation can be perturbed and are still likely to achieve a given percentage of the optimal capacity increase compared to a constellation that maximizes d.sub.min, are also described. Capacity measures that are used in the selection of the location of constellation points include, but are not limited to, parallel decode (PD) capacity and joint capacity.

Three-dimensional carbon nanotubes for high capacity lithium-ion batteries

NASA Astrophysics Data System (ADS)

Kang, Chiwon; Patel, Mumukshu; Rangasamy, Baskaran; Jung, Kyu-Nam; Xia, Changlei; Shi, Sheldon; Choi, Wonbong

2015-12-01

Carbon nanotubes (CNTs) have been considered as a potential anode material for next generation Lithium-ion batteries (LIBs) due to their high conductivity, flexibility, surface area, and lithium-ion insertion ability. However, the low mass loading and bulk density of carbon nanomaterials hinder their use in large-scale energy storage because their high specific capacity may not scale up linearly with the thickness of the electrode. To address this issue, a novel three-dimensional (3D) architecture is rationally designed by stacking layers of free-standing CNTs with the increased areal density to 34.9 mg cm-2, which is around three-times higher than that of the state-of-the-art graphitic anodes. Furthermore, a thermal compression process renders the bulk density of the multi-stacked 3D CNTs to be increased by 1.85 g cm-3, which yields an excellent volumetric capacity of 465 mAh cm-3 at 0.5C. Our proposed strategy involving the stacking of 3D CNT based layers and post-thermal compression provides a powerful platform for the utilization of carbon nanomaterials in the advanced LIB technology.

High-performance sodium–organic battery by realizing four-sodium storage in disodium rhodizonate

DOE Office of Scientific and Technical Information (OSTI.GOV)

Lee, Minah; Hong, Jihyun; Lopez, Jeffrey

Sodium-ion batteries (SIBs) for grid-scale applications need active materials that combine a high energy density with sustainability. Given the high theoretical specific capacity 501 mAh g -1, and Earth abundance of disodium rhodizonate (Na 2C 6O 6), it is one of the most promising cathodes for SIBs. However, substantially lower reversible capacities have been obtained compared with the theoretical value and the understanding of this discrepancy has been limited. In this paper, we reveal that irreversible phase transformation of Na 2C 6O 6 during cycling is the origin of the deteriorating redox activity of Na 2C 6O 6. The active-particlemore » size and electrolyte conditions were identified as key factors to decrease the activation barrier of the phase transformation during desodiation. Finally, on the basis of this understanding, we achieved four-sodium storage in a Na 2C 6O 6 electrode with a reversible capacity of 484 mAh g -1, an energy density of 726 Wh kg -1 cathode, an energy efficiency above 87% and a good cycle retention.« less

Morphological control of three-dimensional carbon nanotube anode for high-capacity lithium-ion battery

NASA Astrophysics Data System (ADS)

Kang, Chiwon; Lee, Hoo-Jeong

2018-05-01

In this paper, we report the results of modulating the processing conditions (mainly, temperature) of a two-step method consisting of sputtering deposition of a Ni catalytic layer and chemical vapor deposition (CVD) of carbon nanotubes (CNTs) on a three-dimensional (3D)-structured Cu mesh to control the morphology of CNTs for advanced Li-ion battery (LIB) applications. We disclosed that CNT growth at a low temperature (700 °C) produced small-diameter CNTs (CNT_S) with an average diameter of ∼20 nm, while that at a high temperature (750 °C) produced large-diameter CNTs (CNT_L) with an average diameter of 200–300 nm. The high-resolution transmission electron microscopy (HR-TEM) and Raman analyses manifested poorly crystalline CNTs for both samples. CNTS showed a specific capacity of 476 mAh g‑1, which is ∼176% superior to that of CNTL (271 mAh g‑1) and ∼128% higher than the theoretical capacity of the state-of-the-art graphites and recently reported nanostructured carbon-based anode materials.

A trilayer separator with dual function for high performance lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Song, Rensheng; Fang, Ruopian; Wen, Lei; Shi, Ying; Wang, Shaogang; Li, Feng

2016-01-01

In this article, we propose a trilayer graphene/polypropylene/Al2O3 (GPA) separator with dual function for high performance lithium-sulfur (Li-S) batteries. Graphene is coated on one side of polypropylene (PP) separator, which functions as a conductive layer and an electrolyte reservoir that allows for rapid electron and ion transport. Then Al2O3 particles are coated on the other side to further enhance thermal stability and safety of the graphene coated polypropylene (GCP) separator, which are touched with lithium metal anode in the Li-S battery. The GPA separator shows good thermal stability after heating at 157 °C for 10 min while both GCP and PP separators showing an obvious shrinkage about 10%. The initial discharge specific capacity of Li-S coin cell with a GPA separator could reach 1067.7 mAh g-1 at 0.2C. After 100 discharge/charge cycles, it can still deliver a reversible capacity of as high as 804.4 mAh g-1 with 75% capacity retention. The pouch cells further confirm that the trilayer design has great promise towards practical applications.

Self-Substitution and the Temperature Effects on the Electrochemical Performance in the High Voltage Cathode System LiMn 1.5+xNi 0.5-xO 4 (x = 0.1)

DOE PAGES

Xu, Yun; Zhao, Mingyang; Khalid, Syed; ...

2017-05-09

The high voltage cathode material, LiMn 1.6Ni 0.4O 4, was prepared by a polymer-assisted method. The novelty of this paper is the substitution of Ni with Mn, which already exists in the crystal structure instead of other isovalent metal ion dopants which would result in capacity loss. The electrochemical performance testing including stability and rate capability was evaluated. The temperature was found to impose a change on the valence and structure of the cathode materials. Specifically, manganese tends to be reduced at a high temperature of 800 °C and leads to structural changes. The manganese substituted LiMn 1.5Ni 0.5O 4more » (LMN) has proved to be a good candidate material for Li-ion battery cathodes displaying good rate capability and capacity retention. Finally, the cathode materials processed at 550 °C showed a stable performance with negligible capacity loss for 400 cycles.« less

VS4 Nanoparticles Anchored on Graphene Sheets as a High-Rate and Stable Electrode Material for Sodium Ion Batteries.

PubMed

Pang, Qiang; Zhao, Yingying; Yu, Yanhao; Bian, Xiaofei; Wang, Xudong; Wei, Yingjin; Gao, Yu; Chen, Gang

2018-02-22

The size and conductivity of the electrode materials play a significant role in the kinetics of sodium-ion batteries. Various characterizations reveal that size-controllable VS 4 nanoparticles can be successfully anchored on the surface of graphene sheets (GSs) by a simple cationic-surfactant-assisted hydrothermal method. When used as an electrode material for sodium-ion batteries, these VS 4 @GS nanocomposites show large specific capacity (349.1 mAh g -1 after 100 cycles), excellent long-term stability (84 % capacity retention after 1200 cycles), and high rate capability (188.1 mAh g -1 at 4000 mA g -1 ). A large proportion of the capacity was contributed by capacitive processes. This remarkable electrochemical performance was attributed to synergistic interactions between nanosized VS 4 particles and a highly conductive graphene network, which provided short diffusion pathways for Na + ions and large contact areas between the electrolyte and electrode, resulting in considerably improved electrochemical kinetic properties. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Core-shell Si@TiO 2 nanosphere anode by atomic layer deposition for Li-ion batteries

DOE PAGES

Dai, Sheng

2016-01-28

Silicon (Si) is regarded as next-generation anode for high-energy lithium-ion batteries (LIBs) due to its high Li storage capacity (4200 mA h g -1). However, the mechanical degradation and resultant capacity fade critically hinder its practical application. In this regard, we demonstrate that nanocoating of Si spheres with a 3 nm titanium dioxide (TiO 2) layer via atomic layer deposition (ALD) can utmostly balance the high conductivity and the good structural stability to improve the cycling stability of Si core material. The resultant sample, Si@TiO 2-3 nm core–shell nanospheres, exhibits the best electrochemical performance of all with a highest initialmore » Coulombic efficiency and specific charge capacity retention after 50 cycles at 0.1C (82.39% and 1580.3 mA h g -1). In addition to making full advantage of the ALD technique, we believe that our strategy and comprehension in coating the electrode and the active material could provide a useful pathway towards enhancing Si anode material itself and community of LIBs.« less

High-performance sodium–organic battery by realizing four-sodium storage in disodium rhodizonate

DOE PAGES

Lee, Minah; Hong, Jihyun; Lopez, Jeffrey; ...

2017-10-09

Sodium-ion batteries (SIBs) for grid-scale applications need active materials that combine a high energy density with sustainability. Given the high theoretical specific capacity 501 mAh g -1, and Earth abundance of disodium rhodizonate (Na 2C 6O 6), it is one of the most promising cathodes for SIBs. However, substantially lower reversible capacities have been obtained compared with the theoretical value and the understanding of this discrepancy has been limited. In this paper, we reveal that irreversible phase transformation of Na 2C 6O 6 during cycling is the origin of the deteriorating redox activity of Na 2C 6O 6. The active-particlemore » size and electrolyte conditions were identified as key factors to decrease the activation barrier of the phase transformation during desodiation. Finally, on the basis of this understanding, we achieved four-sodium storage in a Na 2C 6O 6 electrode with a reversible capacity of 484 mAh g -1, an energy density of 726 Wh kg -1 cathode, an energy efficiency above 87% and a good cycle retention.« less

Fabrication of Si negative electrodes for Li-ion batteries (LIBs) using cross-linked polymer binders.

PubMed

Jang, Suk-Yong; Han, Sien-Ho

2016-12-19

Currently, Si as an active material for LIBs has been attracting much attention due to its high theoretical specific capacity (3572 mAh g -1 ). However, a disadvantage when using a Si negative electrode for LIBs is the abrupt drop of its capabilities during the cycling process. Therefore, there have been a few studies of polymers such as poly(vinylidene fluoride) (PVdF), carboxymethyl cellulose (CMC), styrene butadiene rubber (SBR) and polyacrylic acid (PAA) given that the robust structure of a polymeric binder to LIBs anodes is a promising means by which to enhance the performance of high-capacity anodes. These studies essentially focused mainly on modifying of the linear-polymer component or on copolymers dissolved in solvents. Cross-linking polymers as a binder may be preferred due to their good scratch resistance, excellent chemical resistance and high levels of adhesion and resilience. However, because these types of polymers (with a rigid structure and cross-linking points) are also insoluble in general organic solvents, applying these types in this capacity is virtually impossible.

High-performance sodium-organic battery by realizing four-sodium storage in disodium rhodizonate

NASA Astrophysics Data System (ADS)

Lee, Minah; Hong, Jihyun; Lopez, Jeffrey; Sun, Yongming; Feng, Dawei; Lim, Kipil; Chueh, William C.; Toney, Michael F.; Cui, Yi; Bao, Zhenan

2017-11-01

Sodium-ion batteries (SIBs) for grid-scale applications need active materials that combine a high energy density with sustainability. Given the high theoretical specific capacity 501 mAh g-1, and Earth abundance of disodium rhodizonate (Na2C6O6), it is one of the most promising cathodes for SIBs. However, substantially lower reversible capacities have been obtained compared with the theoretical value and the understanding of this discrepancy has been limited. Here, we reveal that irreversible phase transformation of Na2C6O6 during cycling is the origin of the deteriorating redox activity of Na2C6O6. The active-particle size and electrolyte conditions were identified as key factors to decrease the activation barrier of the phase transformation during desodiation. On the basis of this understanding, we achieved four-sodium storage in a Na2C6O6 electrode with a reversible capacity of 484 mAh g-1, an energy density of 726 Wh kg-1cathode, an energy efficiency above 87% and a good cycle retention.

Adsorption study of selenium ions from aqueous solutions using MgO nanosheets synthesized by ultrasonic method

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cui, Wenwen; Li, Ping; Wang, Zheming

tMgO nanosheets with thickness ranges of 3–10 molecule layers and high specific area (166.44 m2g-1)were successfully fabricated by an ultrasound-assisted exfoliation method and used as adsorbent forthe removal of both selenite (Se(IV)) and selenate (Se(VI)) from aqueous solutions. The resulting MgOnanosheets displayed high maximum adsorption capacities of 103.52 and 10.28 mg g-1for Se(IV) andSe(VI), respectively. ATR-FTIR and XPS spectroscopic results suggested that both Se(IV) and Se(VI) formedinner-sphere surface complexes on MgO nanosheets under the present experimental conditions. Fur-thermore, high adsorption capacity for Se(IV/VI) in the presence of coexistent anions (SO 4 2-, PO43-, Cl-,and F-) and efficient regeneratability of adsorbentmore » by NaOH solution were observed in the competitiveadsorption and regeneration steps. The simple one-step synthesis process of MgO nanosheets and highadsorption capacities offer a promising method for Se(IV/VI) removal in water treatment.« less

Veterans’ Health Care: Limited Progress Made to Address Concerns That Led to High Risk Designation

DTIC Science & Technology

2017-03-15

partially meet two of the five criteria GAO uses to assess removal from the High-Risk List ( leadership commitment and an action plan), but it has not met...the other three (agency capacity, monitoring efforts, and demonstrated progress). Specifically, VA officials have taken leadership actions such as...high-risk designation, additional actions are required of VA, including: (1) demonstrating stronger leadership support as it continues its

Low-cost carbon-silicon nanocomposite anodes for lithium ion batteries.

PubMed

Badi, Nacer; Erra, Abhinay Reddy; Hernandez, Francisco C Robles; Okonkwo, Anderson O; Hobosyan, Mkhitar; Martirosyan, Karen S

2014-01-01

The specific energy of the existing lithium ion battery cells is limited because intercalation electrodes made of activated carbon (AC) materials have limited lithium ion storage capacities. Carbon nanotubes, graphene, and carbon nanofibers are the most sought alternatives to replace AC materials but their synthesis cost makes them highly prohibitive. Silicon has recently emerged as a strong candidate to replace existing graphite anodes due to its inherently large specific capacity and low working potential. However, pure silicon electrodes have shown poor mechanical integrity due to the dramatic expansion of the material during battery operation. This results in high irreversible capacity and short cycle life. We report on the synthesis and use of carbon and hybrid carbon-silicon nanostructures made by a simplified thermo-mechanical milling process to produce low-cost high-energy lithium ion battery anodes. Our work is based on an abundant, cost-effective, and easy-to-launch source of carbon soot having amorphous nature in combination with scrap silicon with crystalline nature. The carbon soot is transformed in situ into graphene and graphitic carbon during mechanical milling leading to superior elastic properties. Micro-Raman mapping shows a well-dispersed microstructure for both carbon and silicon. The fabricated composites are used for battery anodes, and the results are compared with commercial anodes from MTI Corporation. The anodes are integrated in batteries and tested; the results are compared to those seen in commercial batteries. For quick laboratory assessment, all electrochemical cells were fabricated under available environment conditions and they were tested at room temperature. Initial electrochemical analysis results on specific capacity, efficiency, and cyclability in comparison to currently available AC counterpart are promising to advance cost-effective commercial lithium ion battery technology. The electrochemical performance observed for carbon soot material is very interesting given the fact that its production cost is away cheaper than activated carbon. The cost of activated carbon is about $15/kg whereas the cost to manufacture carbon soot as a by-product from large-scale milling of abundant graphite is about $1/kg. Additionally, here, we propose a method that is environmentally friendly with strong potential for industrialization.

Low-cost carbon-silicon nanocomposite anodes for lithium ion batteries

PubMed Central

2014-01-01

The specific energy of the existing lithium ion battery cells is limited because intercalation electrodes made of activated carbon (AC) materials have limited lithium ion storage capacities. Carbon nanotubes, graphene, and carbon nanofibers are the most sought alternatives to replace AC materials but their synthesis cost makes them highly prohibitive. Silicon has recently emerged as a strong candidate to replace existing graphite anodes due to its inherently large specific capacity and low working potential. However, pure silicon electrodes have shown poor mechanical integrity due to the dramatic expansion of the material during battery operation. This results in high irreversible capacity and short cycle life. We report on the synthesis and use of carbon and hybrid carbon-silicon nanostructures made by a simplified thermo-mechanical milling process to produce low-cost high-energy lithium ion battery anodes. Our work is based on an abundant, cost-effective, and easy-to-launch source of carbon soot having amorphous nature in combination with scrap silicon with crystalline nature. The carbon soot is transformed in situ into graphene and graphitic carbon during mechanical milling leading to superior elastic properties. Micro-Raman mapping shows a well-dispersed microstructure for both carbon and silicon. The fabricated composites are used for battery anodes, and the results are compared with commercial anodes from MTI Corporation. The anodes are integrated in batteries and tested; the results are compared to those seen in commercial batteries. For quick laboratory assessment, all electrochemical cells were fabricated under available environment conditions and they were tested at room temperature. Initial electrochemical analysis results on specific capacity, efficiency, and cyclability in comparison to currently available AC counterpart are promising to advance cost-effective commercial lithium ion battery technology. The electrochemical performance observed for carbon soot material is very interesting given the fact that its production cost is away cheaper than activated carbon. The cost of activated carbon is about $15/kg whereas the cost to manufacture carbon soot as a by-product from large-scale milling of abundant graphite is about $1/kg. Additionally, here, we propose a method that is environmentally friendly with strong potential for industrialization. PMID:25114651

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium-sulfur batteries

NASA Astrophysics Data System (ADS)

Zhao, Cunyu; Liu, Lianjun; Zhao, Huilei; Krall, Andy; Wen, Zhenhai; Chen, Junhong; Hurley, Patrick; Jiang, Junwei; Li, Ying

2013-12-01

Sulfur has received increasing attention as a cathode material for lithium-sulfur (Li-S) batteries due to its high theoretical specific capacity. However, the commercialization of Li-S batteries is limited by the challenges of poor electrical conductivity of sulfur, dissolution of the polysulfide intermediates into the electrolyte, and volume expansion of sulfur during cycling. Herein, we report the fabrication of novel-structured porous carbon microspheres with a controllable multi-modal pore size distribution, i.e., a combination of interconnected micropores, mesopores and macropores. Cathodes made of sulfur infiltrated in such a hierarchical carbon framework provide several advantages: (1) a continuous and high surface area carbon network for enhanced electrical conductivity and high sulfur loading; (2) macropores and large mesopores bridged by small mesopores to provide good electrolyte accessibility and fast Li ion transport and to accommodate volume expansion of sulfur; and (3) small mesopores and micropores to improve carbon/sulfur interaction and to help trap polysulfides. An initial discharge capacity at 1278 mA h g-1 and capacity retention at 70.7% (904 mA h g-1) after 100 cycles at a high rate (1 C) were achieved. The material fabrication process is relatively simple and easily scalable.Sulfur has received increasing attention as a cathode material for lithium-sulfur (Li-S) batteries due to its high theoretical specific capacity. However, the commercialization of Li-S batteries is limited by the challenges of poor electrical conductivity of sulfur, dissolution of the polysulfide intermediates into the electrolyte, and volume expansion of sulfur during cycling. Herein, we report the fabrication of novel-structured porous carbon microspheres with a controllable multi-modal pore size distribution, i.e., a combination of interconnected micropores, mesopores and macropores. Cathodes made of sulfur infiltrated in such a hierarchical carbon framework provide several advantages: (1) a continuous and high surface area carbon network for enhanced electrical conductivity and high sulfur loading; (2) macropores and large mesopores bridged by small mesopores to provide good electrolyte accessibility and fast Li ion transport and to accommodate volume expansion of sulfur; and (3) small mesopores and micropores to improve carbon/sulfur interaction and to help trap polysulfides. An initial discharge capacity at 1278 mA h g-1 and capacity retention at 70.7% (904 mA h g-1) after 100 cycles at a high rate (1 C) were achieved. The material fabrication process is relatively simple and easily scalable. Electronic supplementary information (ESI) available: Preparation process scheme; X-ray mapping images and EDX analysis for the surface of PMC/S-40; X-ray mapping images for the cross-section of PMC/S-40; thermogravimetric analysis (TGA) of PMC/S samples; T-plot results for PMC sample; and electrochemical measurements of lithium-sulfur batteries using PMC/S as cathode materials. See DOI: 10.1039/c3nr04532c

Optical Properties and Electrochemical Performance of LiFePO4 Thin Films Deposited on Transparent Current Collectors.

PubMed

Lee, HyunSeok; Yim, Haena; Kim, Kwang-Bum; Choi, Ji-Won

2015-11-01

LiFePO4 thin film cathodes are deposited on various transparent conducting oxide thin films on glass, which are used as cathode current collectors. The XRD patterns show that the thin films have the phase of LiFePO4 with an ordered olivine structure indexed to the orthorhombic Pmna space group. LiFePO4 thin film deposited on various TCO glass substrates exhibits transmittance of about 53%. The initial specific discharge capacities of LiFePO4 thin films are 25.0 μAh/cm2 x μm on FTO, 33.0 μAh/cm2 x μm on ITO, and 13.0 μAh/cm2 x μm on AZO coated glass substrates. Interestingly, the retention capacities of LiFePO4 thin films are 76.0% on FTO, 31.2% on ITO, and 37.7% on AZO coated glass substrates at 20th cycle. The initial specific discharge capacity of the LiFePO4/FTO electrode is slightly lower, but the discharge capacities of the LiFePO4/FTO electrode relatively decrease less than those of the others such as LiFePO4/ITO and LiFePO4/AZO with cycling. The results reported here provide the high transparency of LiFePO4 thin films cathode materials and the good candidate as FTO current collector of the LiFePO4 thin film cathode of transparent thin film rechargeable batteries due to its high transparency and cyclic retention.

Hierarchical Porous Intercalation-Type V2 O3 as High-Performance Anode Materials for Li-Ion Batteries.

PubMed

Liu, Pengcheng; Zhu, Kongjun; Xu, Yuan; Bian, Kan; Wang, Jing; Tai, Guo'an; Gao, Yanfeng; Luo, Hongjie; Lu, Li; Liu, Jinsong

2017-06-01

As intercalation-type anode materials for Li-ion batteries (LIBs), the commercially used graphite and Li 4 Ti 5 O 12 exhibit good cycling and rate properties, but their theoretical specific capacities are too low to meet the ever-growing demands of high-energy applications such as electric vehicles. Therefore, the development of new intercalation-type anode materials with larger capacity is very desirable. Herein, we design and synthesize novel 3 D hierarchical porous V 2 O 3 @C micro/nanostructures consisting of crumpled nanosheets, through self-reduction under annealing from the structurally similar VO 2 (B)@C precursors without the addition of any other reducing reagent or gas. Excitingly, it is found for the first time through ex situ XRD technology that V 2 O 3 is a new, promising intercalation-type anode material for LIBs with a high capacity. V 2 O 3 @C micro/nanostructures can deliver a large capacity of 732 mAh g -1 without capacity loss at 100 mA g -1 even after 136 cycles, as well as exhibiting excellent cycling and rate performances. The application of V 2 O 3 for Na-ion batteries (NIBs) is elaborated for the first time, and excitingly, it is found that V 2 O 3 @C micro/nanostructures may be promising anode materials for NIBs. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

In-depth analysis and discussions of water absorption-typed high power laser calorimeter

NASA Astrophysics Data System (ADS)

Wei, Ji Feng

2017-02-01

In high-power and high-energy laser measurement, the absorber materials can be easily destroyed under long-term direct laser irradiation. In order to improve the calorimeter's measuring capacity, a measuring system directly using water flow as the absorber medium was built. The system's basic principles and the designing parameters of major parts were elaborated. The system's measuring capacity, the laser working modes, and the effects of major parameters were analyzed deeply. Moreover, the factors that may affect the accuracy of measurement were analyzed and discussed. The specific control measures and methods were elaborated. The self-calibration and normal calibration experiments show that this calorimeter has very high accuracy. In electrical calibration, the average correction coefficient is only 1.015, with standard deviation of only 0.5%. In calibration experiments, the standard deviation relative to a middle-power standard calorimeter is only 1.9%.

Facile synthesis of nanostructured transition metal oxides as electrodes for Li-ion batteries

NASA Astrophysics Data System (ADS)

Opra, Denis P.; Gnedenkov, Sergey V.; Sokolov, Alexander A.; Minaev, Alexander N.; Kuryavyi, Valery G.; Sinebryukhov, Sergey L.

2017-09-01

At all times, energy storage is one of the greatest scientific challenge. Recently, Li-ion batteries are under special attention due to high working voltage, long cycle life, low self-discharge, reliability, no-memory effect. However, commercial LIBs usage in medium- and large-scale energy storage are limited by the capacity of lithiated metal oxide cathode and unsafety of graphite anode at high-rate charge. In this way, new electrode materials with higher electrochemical performance should be designed to satisfy a requirement in both energy and power. As it known, nanostructured transition metal oxides are promising electrode materials because of their elevated specific capacity and high potential vs. Li/Li+. In this work, the perspective of an original facile technique of pulsed high-voltage plasma discharge in synthesis of nanostructured transition metal oxides as electrodes for lithium-ion batteries has been demonstrated.

Sodium-Ion Batteries: Improving the Rate Capability of 3D Interconnected Carbon Nanofibers Thin Film by Boron, Nitrogen Dual-Doping.

PubMed

Wang, Min; Yang, Yang; Yang, Zhenzhong; Gu, Lin; Chen, Qianwang; Yu, Yan

2017-04-01

Boron, nitrogen dual-doping 3D hard carbon nanofibers thin film is synthesized using a facile process. The nanofibers exhibit high specific capacity and remarkable high-rate capability due to the synergistic effect of 3D porous structure, large surface area, and enlarged carbon layer spacing, and the B, N codoping-induced defects.

Nanostructured Si(₁-x)Gex for tunable thin film lithium-ion battery anodes.

PubMed

Abel, Paul R; Chockla, Aaron M; Lin, Yong-Mao; Holmberg, Vincent C; Harris, Justin T; Korgel, Brian A; Heller, Adam; Mullins, C Buddie

2013-03-26

Both silicon and germanium are leading candidates to replace the carbon anode of lithium ions batteries. Silicon is attractive because of its high lithium storage capacity while germanium, a superior electronic and ionic conductor, can support much higher charge/discharge rates. Here we investigate the electronic, electrochemical and optical properties of Si(1-x)Gex thin films with x = 0, 0.25, 0.5, 0.75, and 1. Glancing angle deposition provided amorphous films of reproducible nanostructure and porosity. The film's composition and physical properties were investigated by X-ray photoelectron spectroscopy, four-point probe conductivity, Raman, and UV-vis absorption spectroscopy. The films were assembled into coin cells to test their electrochemical properties as a lithium-ion battery anode material. The cells were cycled at various C-rates to determine the upper limits for high rate performance. Adjusting the composition in the Si(1-x)Gex system demonstrates a trade-off between rate capability and specific capacity. We show that high-capacity silicon anodes and high-rate germanium anodes are merely the two extremes; the composition of Si(1-x)Gex alloys provides a new parameter to use in electrode optimization.

Vertical Graphene Growth on SiO Microparticles for Stable Lithium Ion Battery Anodes.

PubMed

Shi, Liurong; Pang, Chunlei; Chen, Shulin; Wang, Mingzhan; Wang, Kexin; Tan, Zhenjun; Gao, Peng; Ren, Jianguo; Huang, Youyuan; Peng, Hailin; Liu, Zhongfan

2017-06-14

Silicon-based materials are considered as strong candidates to next-generation lithium ion battery anodes because of their ultrahigh specific capacities. However, the pulverization and delamination of electrochemical active materials originated from the huge volume expansion (>300%) of silicon during the lithiation process results in rapid capacity fade, especially in high mass loading electrodes. Here we demonstrate that direct chemical vapor deposition (CVD) growth of vertical graphene nanosheets on commercial SiO microparticles can provide a stable conducting network via interconnected vertical graphene encapsulation during lithiation, thus remarkably improving the cycling stability in high mass loading SiO anodes. The vertical graphene encapsulated SiO (d-SiO@vG) anode exhibits a high capacity of 1600 mA h/g and a retention up to 93% after 100 cycles at a high areal mass loading of 1.5 mg/cm 2 . Furthermore, 5 wt % d-SiO@vG as additives increased the energy density of traditional graphite/NCA 18650 cell by ∼15%. We believe that the results strongly imply the important role of CVD-grown vertical graphene encapsulation in promoting the commercial application of silicon-based anodes.

Multipeak low-temperature behavior of specific heat capacity in frustrated magnetic systems: An exact theoretical analysis

NASA Astrophysics Data System (ADS)

Jurčišinová, E.; Jurčišin, M.

2018-05-01

We investigate in detail the process of formation of the multipeak low-temperature structure in the behavior of the specific heat capacity in frustrated magnetic systems in the framework of the exactly solvable antiferromagnetic spin-1 /2 Ising model with the multisite interaction in the presence of the external magnetic field on the kagome-like Husimi lattice. The behavior of the entropy of the model is studied and exact values of the residual entropies of all ground states are found. It is shown that the multipeak structure in the behavior of the specific heat capacity is related to the formation of the multilevel hierarchical ordering in the system of all ground states of the model. Direct relation between the maximal number of peaks in the specific heat capacity behavior and the number of independent interactions in studied frustrated magnetic system is identified. The mechanism of the formation of the multipeak structure in the specific heat capacity is described and studied in detail, and it is generalized to frustrated magnetic systems with arbitrary numbers of independent interactions.

Rational design of Fe3O4@C yolk-shell nanorods constituting a stable anode for high-performance Li/Na-ion batteries.

PubMed

Wang, Beibei; Zhang, Xing; Liu, Xiaojie; Wang, Gang; Wang, Hui; Bai, Jintao

2018-05-24

In the current research project, we have prepared a novel Fe 3 O 4 @mesoporous carbon nanorod (denoted as Fe 3 O 4 @C) anode with yolk-shell structure for Li/Na-ion batteries via one-pot and surfactant-free synthesis strategy. The yolk-shell structure consists of Fe 3 O 4 nanorod yolk completely protected by a well-conductive mesoporous carbon shell. The substantial void space in the Fe 3 O 4 @C yolk-shell nanorod can not only accommodate the full volume expansion of inner Fe 3 O 4 nanorod, but also preserve the structural integrity of the Fe 3 O 4 @C anode and develop a stable SEI film on the outside mesoporous carbon shell during the repeated Li + /Na + insertion/extraction processes. As for lithium storage, the Fe 3 O 4 @C electrode exhibits a high specific capacity (1247 mAh g -1 ), stable cycling performance (a specific capacity of 954 mAh g -1 after 200 cycles at a current density of 0.5 A g -1 ) and excellent rate capability (specific capabilities of 1122, 958, 783, 577, and 374 mAh g -1 at 0.5, 1, 2, 4, and 8 A g -1 , respectively). As for sodium storage, the Fe 3 O 4 @C yolk-shell nanorods also maintain a reversible capacity of approximate 424 mAh g -1 at 0.1 A g -1 after 100 cycles. Copyright © 2018. Published by Elsevier Inc.

CD8(+) T-cell Cytotoxic Capacity Associated with Human Immunodeficiency Virus-1 Control Can Be Mediated through Various Epitopes and Human Leukocyte Antigen Types.

PubMed

Migueles, Stephen A; Mendoza, Daniel; Zimmerman, Matthew G; Martins, Kelly M; Toulmin, Sushila A; Kelly, Elizabeth P; Peterson, Bennett A; Johnson, Sarah A; Galson, Eric; Poropatich, Kate O; Patamawenu, Andy; Imamichi, Hiromi; Ober, Alexander; Rehm, Catherine A; Jones, Sara; Hallahan, Claire W; Follmann, Dean A; Connors, Mark

2015-01-01

Understanding natural immunologic control over Human Immunodeficiency Virus (HIV)-1 replication, as occurs in rare long-term nonprogressors/elite controllers (LTNP/EC), should inform the design of efficacious HIV vaccines and immunotherapies. Durable control in LTNP/EC is likely mediated by highly functional virus-specific CD8(+) T-cells. Protective Human Leukocyte Antigen (HLA) class I alleles, like B*27 and B*57, are present in most, but not all LTNP/EC, providing an opportunity to investigate features shared by their HIV-specific immune responses. To better understand the contribution of epitope targeting and conservation to immune control, we compared the CD8(+) T-cell specificity and function of B*27/57(neg) LTNP/EC (n = 23), B*27/57(pos) LTNP/EC (n = 23) and B*27/57(neg) progressors (n = 13). Fine mapping revealed 11 previously unreported immunodominant responses. Although B*27/57(neg) LTNP/EC did not target more highly conserved epitopes, their CD8(+) T-cell cytotoxic capacity was significantly higher than progressors. Similar to B*27/57(pos) LTNP/EC, this superior cytotoxicity was mediated by preferential expansion of immunodominant responses and lysis through the predicted HLA. These findings suggest that increased CD8(+) T-cell cytotoxic capacity is a common mechanism of control in most LTNP/EC regardless of HLA type. They also suggest that potent cytotoxicity can be mediated through various epitopes and HLA molecules and could, in theory, be induced in most people.

CD8+ T-cell Cytotoxic Capacity Associated with Human Immunodeficiency Virus-1 Control Can Be Mediated through Various Epitopes and Human Leukocyte Antigen Types

PubMed Central

Migueles, Stephen A.; Mendoza, Daniel; Zimmerman, Matthew G.; Martins, Kelly M.; Toulmin, Sushila A.; Kelly, Elizabeth P.; Peterson, Bennett A.; Johnson, Sarah A.; Galson, Eric; Poropatich, Kate O.; Patamawenu, Andy; Imamichi, Hiromi; Ober, Alexander; Rehm, Catherine A.; Jones, Sara; Hallahan, Claire W.; Follmann, Dean A.; Connors, Mark

2014-01-01

Understanding natural immunologic control over Human Immunodeficiency Virus (HIV)-1 replication, as occurs in rare long-term nonprogressors/elite controllers (LTNP/EC), should inform the design of efficacious HIV vaccines and immunotherapies. Durable control in LTNP/EC is likely mediated by highly functional virus-specific CD8+ T-cells. Protective Human Leukocyte Antigen (HLA) class I alleles, like B*27 and B*57, are present in most, but not all LTNP/EC, providing an opportunity to investigate features shared by their HIV-specific immune responses. To better understand the contribution of epitope targeting and conservation to immune control, we compared the CD8+ T-cell specificity and function of B*27/57neg LTNP/EC (n = 23), B*27/57pos LTNP/EC (n = 23) and B*27/57neg progressors (n = 13). Fine mapping revealed 11 previously unreported immunodominant responses. Although B*27/57neg LTNP/EC did not target more highly conserved epitopes, their CD8+ T-cell cytotoxic capacity was significantly higher than progressors. Similar to B*27/57pos LTNP/EC, this superior cytotoxicity was mediated by preferential expansion of immunodominant responses and lysis through the predicted HLA. These findings suggest that increased CD8+ T-cell cytotoxic capacity is a common mechanism of control in most LTNP/EC regardless of HLA type. They also suggest that potent cytotoxicity can be mediated through various epitopes and HLA molecules and could, in theory, be induced in most people. PMID:26137533

The effect of predator exposure and reproduction on oxidative stress parameters in the Catarina scallop Argopecten ventricosus.

PubMed

Guerra, C; Zenteno-Savín, T; Maeda-Martínez, A N; Abele, D; Philipp, E E R

2013-05-01

Predation is known to impact growth and reproduction, and the physiological state of the prey, including its susceptibility to oxidative stress. In this study, we investigated how prolonged exposure to predators modulates tissue specific antioxidant defense and oxidative damage in the short-lived epibenthic scallop Argopecten ventricosus (2years maximum lifespan). Scallops that were experimentally exposed to predators had not only lower antioxidant capacities (superoxide dismutase and catalase), but also lower oxidative damage (protein carbonyls and TBARS=thiobarbituric acid reactive substances including lipid peroxides) in gills and mantle compared to individuals not exposed to predators. In contrast, oxidative damage in the swimming muscle was higher in predator-exposed scallops. When predator-exposed scallops were on the verge of spawning, levels of oxidative damage increased in gills and mantle in spite of a parallel increase in antioxidant defense in both tissues. Levels of oxidative damage increased also in the swimming muscle whereas muscle antioxidant capacities decreased. Interestingly, post-spawned scallops restored antioxidant capacities and oxidative damage to immature levels, suggesting they can recover from spawning-related oxidative stress. Our results show that predator exposure and gametogenesis modulate oxidative damage in a tissue specific manner and that high antioxidant capacities do not necessarily coincide with low oxidative damage. Copyright © 2013 Elsevier Inc. All rights reserved.

A Subgroup Analysis of the Impact of Vortioxetine on Functional Capacity, as Measured by UPSA, in Patients with Major Depressive Disorder and Subjective Cognitive Dysfunction.

PubMed

Keefe, Richard S E; Nomikos, George; Zhong, Wei; Christensen, Michael Cronquist; Jacobson, William

2018-05-01

We evaluated vortioxetine's effects on functional capacity in demographic and clinical subgroups of patients with major depressive disorder. This was an exploratory analysis of the CONNECT study (NCT01564862) that evaluated changes in functional capacity using University of California San Diego Performance-based Skills Assessment data, categorized by sex, age, education, employment status, and baseline disease severity (Montgomery-Åsberg Depression Rating Scale, Clinical Global Impressions-Severity of Illness). Greater changes in University of California San Diego Performance-based Skills Assessment composite scores were observed with vortioxetine vs placebo in specific subgroups: males (∆+3.2), females (∆+2.9), 45-54 or ≥55 years (∆+5.6, ∆+3.4), working (∆+2.8), high school or greater education (∆+2.7, ∆+2.8), disease severity (Montgomery-Åsberg Depression Rating Scale, <30, ∆+3.5; ≥30, ∆+2.5; Clinical Global Impressions-Severity of Illness ≤4, ∆+2.8; >4, ∆+3.0), major depressive episodes (≤2, >2 [∆+2.7,+3.3]), and episode duration (≤22, >22 weeks [∆+3.7,+2.4]). Our findings support the need for additional studies to assess whether vortioxetine improves functional capacity within specific patient subgroups. clinicaltrials.gov: NCT01564862.

Sodium-oxygen batteries with alkyl-carbonate and ether based electrolytes.

PubMed

Kim, Jinsoo; Lim, Hee-Dae; Gwon, Hyeokjo; Kang, Kisuk

2013-03-14

Recently, metal-air batteries, such as lithium-air and zinc-air systems, have been studied extensively as potential candidates for ultra-high energy density storage devices because of their exceptionally high capacities. Here, we report such an electrochemical system based on sodium, which is abundant and inexpensive. Two types of sodium-oxygen batteries were introduced and studied, i.e. with carbonate and non-carbonate electrolytes. Both types could deliver specific capacities (2800 and 6000 mA h g(-1)) comparable to that of lithium-oxygen batteries but with slightly lower discharge voltages (2.3 V and 2.0 V). The reaction mechanisms of sodium-oxygen batteries in carbonate and non-carbonate electrolytes were investigated and compared with those of lithium-oxygen batteries.

Electrochemical performance of Fe3O4 micro flower as anode for lithium ion batteries

NASA Astrophysics Data System (ADS)

Noerochim, Lukman; Anggara, Dika; Susanti, Diah; Subhan, Achmad; Sudaryanto

2018-04-01

Graphite is generally employed in commercial lithium ion batteries which has a specific capacity of 372 mAh/g. In this study, graphite is replaced with carbon-coated magnetite (Fe3O4/C) which has large theoretical specific capacity of 926 mAh/g, environmental friendly, and low cost production. The synthesis of Fe3O4/C is carried out by hydrothermal method with reacting FeCl3 and hexamethylenetetramine (HMT) at temperature variation of 160, 170 and 180°C. The following process is heated by calcination at temperature variations 450, 500 and 550°C. XRD and SEM results show that the as-prepared Fe3O4/C powder has a single phase of Fe3O4 and morphology micro-flowers like with size between 700 nm - 3 µm. CV test results show redox reaction occurs in the voltage range between 0.21-0.85 V and 1.68-1.81 V. The highest specific discharge capacity is obtained 644 mAh/g for specimen with temperature hydrothermal of 170°C and temperature calcination of 550°C. This result shows that Fe3O4/C has a high potential as anode material for lithium ion battery.

Capacity of blood plasma is higher in birds breeding in radioactively contaminated areas

PubMed Central

Møller, Anders P.; Mousseau, Timothy A.; Soler, Juan J.

2017-01-01

Background Environmental pollution in general, and radioactive contamination in particular, may deeply affect host-parasite relationships and their consequences for the evolution of organisms. The nuclear accident that occurred more than 30 years ago in Chernobyl resulted in significant changes in diversity and richness of microbial communities that could influence characteristics of animal-bacteria interactions, including host immune responses and competitive interference by bacteria. Given the high mortality rate of birds breeding in radioactively contaminated zones, those with stronger defences against infections should experience significant fitness advantages. Methodology/Principal Findings Here we characterized antimicrobial capacity of barn swallows (Hirundo rustica) from different Ukrainian populations (subject to a gradient of ionizing radiation) against 12 bacterial species. We also quantified constitutive innate immunity, which is the non-specific first barrier of protection of hosts against microbial parasites. We found a positive association between specific antimicrobial capacity of individual hosts and radiation levels in breeding habitats even after controlling for other confounding variables such as sex and age. However, no significant relationship was found between immunocompetence (non-specific response) and background radiation. Conclusions/Significance These results suggest that radiation selects for broad antimicrobial spectra of barn swallows, although not for all bacterial strains. We discuss these results in the framework of host-parasite evolution under extreme environmental conditions. PMID:28662048

Anxiety sensitivity and working memory capacity: Risk factors and targets for health behavior promotion.

PubMed

Otto, Michael W; Eastman, Abraham; Lo, Stephen; Hearon, Bridget A; Bickel, Warren K; Zvolensky, Michael; Smits, Jasper A J; Doan, Stacey N

2016-11-01

Understanding the nature and influence of specific risk profiles is increasingly important for health behavior promotion. The purpose of this article is to document the value of two factors-anxiety sensitivity (AS) and working memory capacity (WMC)-for enhancing risk for the initiation and/or maintenance of a range of negative health behaviors. AS is a distress-related risk factor that potentiates avoidance/coping motivations for negative health behaviors. Stress provides the conditions for negative somatic and affective states, and AS amplifies the aversiveness of these experiences and correspondingly hinders adaptive functioning. In contrast, low WMC is hypothesized to exert its effect by decreasing the capacity to filter out current temptations, attenuating a focus on longer-term goals and impairing the application of relevant coping skills at times of stress. In this review, we provide conceptual models for the separate roles of high AS and low WMC in negative health behaviors, review the influence of these factors on specific health behavior exemplars (eating behaviors/obesity, physical activity, smoking, alcohol use, and sleep promotion), provide preliminary evidence for their value as independent treatment targets for health-behavior promotion, and encourage specific research directions in relation to these variables. Copyright © 2016. Published by Elsevier Ltd.

Design of a Porous Cathode for Ultrahigh Performance of a Li-ion Battery: An Overlooked Pore Distribution

PubMed Central

Song, Jihwan; Kim, Junhyung; Kang, Taewook; Kim, Dongchoul

2017-01-01

Typical cathode materials of Li-ion battery suffer from a severe loss in specific capacity, and this problem is regarded as a major obstacle in the expansion of newer applications. To overcome this, porous cathodes are being extensively utilized. However, although it seems that the porosity in the cathode would be a panacea for high performance of LIBs, there is a blind point in the cathode consisting of porous structures, which makes the porous design to be a redundant. Here, we report the importance of designing the porosity of a cathode in obtaining ultrahigh performance with the porous design or a degraded performance even with increase of porosity. Numerical simulations show that the cathode with 40% porosity has 98% reduction in the loss of specific capacity when compared to the simple spherical cathode when the C-rate increases from 2.5 to 80 C. In addition, the loss over total cycles decreases from 30% to only about 1% for the cathode with 40% porosity under 40 C. Interestingly, however, the specific capacity could be decreased even with the increase in porosity unless the pores were evenly distributed in the cathode. The present analysis provides an important insight into the design of ultrahigh performance cathodes. PMID:28211894

Activated carbon derived from harmful aquatic plant for high stable supercapacitors

NASA Astrophysics Data System (ADS)

Li, Jiangfeng; Wu, Qingsheng

2018-01-01

Considering cost and environmental protection, the harmful aquatic plant altemanthera philoxeroides derived carbon material with super high specific surface area (2895 m2 g-1) is an ideal electrode material for supercapacitor. The structure and composition of these carbon materials were characterized by SEM, EDS, XPS and BET measurements. The obtained material exhibits a maximum specific capacitance of 275 F g-1 at 0.5 A g-1 and retains a capacitance of 210 F g-1 even at 50 A g-1. In addition, it also shows excellent capacity retention of 5000 cycles at 10 A g-1.

A REGIONAL ANALYSIS OF LAKE ACIDIFICATION TRENDS FOR THE NORTHEASTEN U.S., 1982-1994

EPA Science Inventory

Acidic deposition is a regional phenomenon, but its effects have traditionally been studied using site-specific, intensive monitoring. We present trends information for 36 lakes of high-to-moderate acid sensitivity (defined as acid neutralizing capacity [ANC] < 100 eq L-1),and 1...

Educational Measurement and Knowledge of Other Minds

ERIC Educational Resources Information Center

Curren, Randall R.

2004-01-01

This article addresses the capacity of high stakes tests to measure the most significant kinds of learning. It begins by examining a set of philosophical arguments pertaining to construct validity and alleged conceptual obstacles to attributing specific knowledge and skills to learners. The arguments invoke philosophical doctrines of holism and…

Modality Specificity and Integration in Working Memory: Insights from Visuospatial Bootstrapping

ERIC Educational Resources Information Center

Allen, Richard J.; Havelka, Jelena; Falcon, Thomas; Evans, Sally; Darling, Stephen

2015-01-01

The question of how meaningful associations between verbal and spatial information might be utilized to facilitate working memory performance is potentially highly instructive for models of memory function. The present study explored how separable processing capacities within specialized domains might each contribute to this, by examining the…

76 FR 12095 - Monroe Gas Storage Company, LLC; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2011-03-04

... Storage Company, LLC; Notice of Application Take notice that on February 18, 2011, Monroe Gas Storage... Monroe Gas Storage Project. Specifically, through this Application, Monroe seeks authorization to (1...) of high-deliverability working gas storage capacity, with about 4.46 Bcf of base gas. Nor is any...

Bioinformatics and Astrophysics Cluster (BinAc)

NASA Astrophysics Data System (ADS)

Krüger, Jens; Lutz, Volker; Bartusch, Felix; Dilling, Werner; Gorska, Anna; Schäfer, Christoph; Walter, Thomas

2017-09-01

BinAC provides central high performance computing capacities for bioinformaticians and astrophysicists from the state of Baden-Württemberg. The bwForCluster BinAC is part of the implementation concept for scientific computing for the universities in Baden-Württemberg. Community specific support is offered through the bwHPC-C5 project.

Boosting the power performance of multilayer graphene as lithium-ion battery anode via unconventional doping with in-situ formed Fe nanoparticles

PubMed Central

Raccichini, Rinaldo; Varzi, Alberto; Chakravadhanula, Venkata Sai Kiran; Kübel, Christian; Passerini, Stefano

2016-01-01

Graphene is extensively investigated and promoted as a viable replacement for graphite, the state-of-the-art material for lithium-ion battery (LIB) anodes, although no clear evidence is available about improvements in terms of cycling stability, delithiation voltage and volumetric capacity. Here we report the microwave-assisted synthesis of a novel graphene-based material in ionic liquid (i.e., carved multilayer graphene with nested Fe3O4 nanoparticles), together with its extensive characterization via several physical and chemical techniques. When such a composite material is used as LIB anode, the carved paths traced by the Fe3O4 nanoparticles, and the unconverted metallic iron formed in-situ upon the 1st lithiation, result in enhanced rate capability and, especially at high specific currents (i.e., 5 A g−1), remarkable cycling stability (99% of specific capacity retention after 180 cycles), low average delithiation voltage (0.244 V) and a substantially increased volumetric capacity with respect to commercial graphite (58.8 Ah L−1 vs. 9.6 Ah L−1). PMID:27026069

Influence of the ZnO nanoarchitecture on the electrochemical performances of binder-free anodes for Li storage

NASA Astrophysics Data System (ADS)

Dall'Asta, V.; Tealdi, C.; Resmini, A.; Anselmi Tamburini, U.; Mustarelli, P.; Quartarone, E.

2017-03-01

Zinc oxide nanoarchitectures may be employed as binder-free, high specific capacity anodes for lithium batteries. By means of simple and low-impact wet chemistry approaches, we synthesized 1D (nanorods), 2D (single- and multi-layered nanosheets), and 3D (nanobrushes) ZnO arrays. These nanoarchitectures were compared as far as concerns their electrochemical properties and the structural modifications upon lithiation/delithiation. The best results were offered by 2D nanosheets, which showed reversible capacity of the order of 400 mAhg-1 after 100 cycles at 1 Ag-1. This was due to: i) small nanoparticles, with average diameter of about 10 nm, which maximize the array specific surface area and favor the formation of the LiZn alloy; ii) the presence of a mesoporous texture, which allows larger space for accommodating the volume changes upon lithiation/delithiation. However, also these 2D structures showed large irreversible capacity losses. Our work highlights the need for more efficient buffering solutions in ZnO binder-free nanostructured anodes.

TiO₂ Nanobelt@Co₉S₈ Composites as Promising Anode Materials for Lithium and Sodium Ion Batteries.

PubMed

Zhou, Yanli; Zhu, Qian; Tian, Jian; Jiang, Fuyi

2017-09-02

TiO₂ anodes have attracted great attention due to their good cycling stability for lithium ion batteries and sodium ion batteries (LIBs and SIBs). Unfortunately, the low specific capacity and poor conductivity limit their practical application. The mixed phase TiO₂ nanobelt (anatase and TiO₂-B) based Co₉S₈ composites have been synthesized via the solvothermal reaction and subsequent calcination. During the formation process of hierarchical composites, glucose between TiO₂ nanobelts and Co₉S₈ serves as a linker to increase the nucleation and growth of sulfides on the surface of TiO₂ nanobelts. As anode materials for LIBs and SIBs, the composites combine the advantages of TiO₂ nanobelts with those of Co₉S₈ nanomaterials. The reversible specific capacity of TiO₂ nanobelt@Co₉S₈ composites is up to 889 and 387 mAh·g -1 at 0.1 A·g -1 after 100 cycles, respectively. The cooperation of excellent cycling stability of TiO₂ nanobelts and high capacities of Co₉S₈ nanoparticles leads to the good electrochemical performances of TiO₂ nanobelt@Co₉S₈ composites.

Impact of phosphate limitation on PHA production in a feast-famine process.

PubMed

Korkakaki, Emmanouela; van Loosdrecht, Mark C M; Kleerebezem, Robbert

2017-12-01

Double-limitation systems have shown to induce polyhydroxyalkanoates (PHA) production in chemostat studies limited in e.g. carbon and phosphate. In this work the impact of double substrate limitation on the enrichment of a PHA producing community was studied in a sequencing batch process. Enrichments at different C/P concentration ratios in the influent were established and the effect on the PHA production capacity and the enrichment community structure was investigated. Experimental results demonstrated that when a double substrate limitation is imposed at a C/P ratio in the influent in a range of 150 (C-mol/mol), the P-content of the biomass and the specific substrate uptake rates decreased. Nonetheless, the PHA storage capacity remained high (with a maximum of 84 wt%). At a C/P ratio of 300, competition in the microbial community is based on phosphate uptake, and the PHA production capacity is lost. Biomass specific substrate uptake rates are a linear function of the cellular P-content, offering advantages for scaling-up the PHA production process due to lower oxygen requirements. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biomass carbon composited FeS2 as cathode materials for high-rate rechargeable lithium-ion battery

NASA Astrophysics Data System (ADS)

Xu, Xin; Meng, Zhen; Zhu, Xueling; Zhang, Shunlong; Han, Wei-Qiang

2018-03-01

Pyrite FeS2 has long been used as commercial primary lithium batteries at room temperature. To achieve rechargeable FeS2 battery, biomass-carbon@FeS2 composites are prepared using green and renewable auricularia auricula as carbon source through the process of carbonization and sulfuration. The auricularia auricula has strong swelling characteristics to absorb aqueous solution which can effectively absorb Fe ions into its body. FeS2 homogeneously distributed in biomass carbon matrix performs high electronic and ionic conductivity. The specific capacity of biomass-carbon@FeS2 composites remains 850 mAh g-1 after 80 cycles at 0.5C and 700 mAh g-1 at the rate of 2C after 150 cycles. Biomass-carbon@FeS2 composites exhibit high-rate capacity in lithium-ion battery.

Facile synthesis of hierarchical mesoporous weirds-like morphological MnO2 thin films on carbon cloth for high performance supercapacitor application.

PubMed

Shinde, Pragati A; Lokhande, Vaibhav C; Ji, Taeksoo; Lokhande, Chandrakant D

2017-07-15

The mesoporous nanostructured metal oxides have a lot of capabilities to upsurge the energy storing capacity of the supercapacitor. In present work, different nanostructured morphologies of MnO 2 have been successfully fabricated on flexible carbon cloth by simple but capable hydrothermal method at different deposition temperatures. The deposition temperature has strong influence on reaction kinetics, which subsequently alters the morphology and electrochemical performance. Among different nanostructured MnO 2 thin films, the mesoporous weirds composed thin film obtained at temperature of 453K exhibits excellent physical and electrochemical features for supercapacitor application. The weirds composed MnO 2 thin film exhibits specific surface area of 109m 2 g -1 , high specific capacitance of 595Fg -1 with areal capacitance of 4.16Fcm -2 at a scan rate of 5mVs -1 and high specific energy of 56.32Whkg -1 . In addition to this, MnO 2 weirds attain capacity retention of 87 % over 2000 CV cycles, representing better cycling stability. The enhanced electrochemical performance could be ascribed to direct growth of highly porous MnO 2 weirds on carbon cloth which provide more pathways for easy diffusion of electrolyte into the interior of electroactive material. The as-fabricated electrode with improved performance could be ascribed as a potential electrode material for energy storage devices. Copyright © 2017 Elsevier Inc. All rights reserved.

Genomic analysis of organismal complexity in the multicellular green alga Volvox carteri

DOE Office of Scientific and Technical Information (OSTI.GOV)

Prochnik, Simon E.; Umen, James; Nedelcu, Aurora

2010-07-01

Analysis of the Volvox carteri genome reveals that this green alga's increased organismal complexity and multicellularity are associated with modifications in protein families shared with its unicellular ancestor, and not with large-scale innovations in protein coding capacity. The multicellular green alga Volvox carteri and its morphologically diverse close relatives (the volvocine algae) are uniquely suited for investigating the evolution of multicellularity and development. We sequenced the 138 Mb genome of V. carteri and compared its {approx}14,500 predicted proteins to those of its unicellular relative, Chlamydomonas reinhardtii. Despite fundamental differences in organismal complexity and life history, the two species have similarmore » protein-coding potentials, and few species-specific protein-coding gene predictions. Interestingly, volvocine algal-specific proteins are enriched in Volvox, including those associated with an expanded and highly compartmentalized extracellular matrix. Our analysis shows that increases in organismal complexity can be associated with modifications of lineage-specific proteins rather than large-scale invention of protein-coding capacity.« less

Methods and Apparatuses for Signaling with Geometric Constellations in a Raleigh Fading Channel

NASA Technical Reports Server (NTRS)

Barsoum, Maged F. (Inventor); Jones, Christopher R. (Inventor)

2017-01-01

Communication systems are described that use signal constellations, which have unequally spaced (i.e. `geometrically` shaped) points. In many embodiments, the communication systems use specific geometric constellations that are capacity optimized at a specific SNR, over the Raleigh fading channel. In addition, ranges within which the constellation points of a capacity optimized constellation can be perturbed and are still likely to achieve a given percentage of the optimal capacity increase compared to a constellation that maximizes d.sub.min, are also described. Capacity measures that are used in the selection of the location of constellation points include, but are not limited to, parallel decode (PD) capacity and joint capacity.

Methods and Apparatuses for Signaling with Geometric Constellations in a Raleigh Fading Channel

NASA Technical Reports Server (NTRS)

Jones, Christopher R. (Inventor); Barsoum, Maged F. (Inventor)

2015-01-01

Communication systems are described that use signal constellations, which have unequally spaced (i.e., `geometrically` shaped) points. In many embodiments, the communication systems use specific geometric constellations that are capacity optimized at a specific SNR (signal to noise ratio). In addition, ranges within which the constellation points of a capacity optimized constellation can be perturbed and are still likely to achieve a given percentage of the optimal capacity increase compared to a constellation that maximizes d (sub min) (i.e. minimum distance between constellations) are also described. Capacity measures that are used in the selection of the location of constellation points include, but are not limited to, parallel decode (PD) capacity and joint capacity.

Older adults do not notice their names: a new twist to a classic attention task.

PubMed

Naveh-Benjamin, Moshe; Kilb, Angela; Maddox, Geoffrey B; Thomas, Jenna; Fine, Hope C; Chen, Tina; Cowan, Nelson

2014-11-01

Although working memory spans are, on average, lower for older adults than young adults, we demonstrate in 5 experiments a way in which older adults paradoxically resemble higher capacity young adults. Specifically, in a selective-listening task, older adults almost always failed to notice their names presented in an unattended channel. This is an exaggeration of what high-span young adults show and the opposite of what low-span young adults show. This striking finding in older adults remained significant after controlling for working memory span and for noticing their names in an attended channel. The findings were replicated when presentation rate was slowed and when the ear in which the unattended name was presented was controlled. These results point to an account of older adults' performance involving not only an inhibition factor, which allows high-span young adults to suppress the channel to be ignored, but also an attentional capacity factor, with more unallocated capacity. This capacity allows low-span young adults to notice their names much more often than older adults with comparably low working memory spans do. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Reversible multi-electron redox chemistry of π-conjugated N-containing heteroaromatic molecule-based organic cathodes

NASA Astrophysics Data System (ADS)

Peng, Chengxin; Ning, Guo-Hong; Su, Jie; Zhong, Guiming; Tang, Wei; Tian, Bingbing; Su, Chenliang; Yu, Dingyi; Zu, Lianhai; Yang, Jinhu; Ng, Man-Fai; Hu, Yong-Sheng; Yang, Yong; Armand, Michel; Loh, Kian Ping

2017-07-01

Even though organic molecules with well-designed functional groups can be programmed to have high electron density per unit mass, their poor electrical conductivity and low cycle stability limit their applications in batteries. Here we report a facile synthesis of π-conjugated quinoxaline-based heteroaromatic molecules (3Q) by condensation of cyclic carbonyl molecules with o-phenylenediamine. 3Q features a number of electron-deficient pyrazine sites, where multiple redox reactions take place. When hybridized with graphene and coupled with an ether-based electrolyte, an organic cathode based on 3Q molecules displays a discharge capacity of 395 mAh g-1 at 400 mA g-1 (1C) in the voltage range of 1.2-3.9 V and a nearly 70% capacity retention after 10,000 cycles at 8 A g-1. It also exhibits a capacity of 222 mAh g-1 at 20C, which corresponds to 60% of the initial specific capacity. Our results offer evidence that heteroaromatic molecules with multiple redox sites are promising in developing high-energy-density, long-cycle-life organic rechargeable batteries.

Improved Li storage performance in SnO 2 nanocrystals by a synergetic doping

DOE PAGES

Wan, Ning; Lu, Xia; Wang, Yuesheng; ...

2016-01-06

Tin dioxide (SnO 2) is a widely investigated lithium (Li) storage material because of its easy preparation, two-step storage mechanism and high specific capacity for lithium-ion batteries (LIBs). In this contribution, a phase-pure cobalt-doped SnO 2 (Co/SnO 2) and a cobalt and nitrogen co-doped SnO 2 (Co-N/SnO 2) nanocrystals are prepared to explore their Li storage behaviors. It is found that the morphology, specific surface area, and electrochemical properties could be largely modulated in the doped and co-doped SnO 2 nanocrystals. Gavalnostatic cycling results indicate that the Co-N/SnO 2 electrode delivers a specific capacity as high as 716 mAh gmore » –1 after 50 cycles, and the same outstanding rate performance can be observed in subsequent cycles due to the ionic/electronic conductivity enhancement by co-doping effect. Further, microstructure observation indicates the existence of intermediate phase of Li 3N with high ionic conductivity upon cycling, which probably accounts for the improvements of Co-N/SnO 2 electrodes. Furthermore, we find that the method of synergetic doping into SnO 2 with Co and N, with which the electrochemical performances is enhanced remarkably, undoubtedly, will have an important influence on the material itself and community of LIBs as well.« less

The Readiness for Integrated Care Questionnaire (RICQ): An instrument to assess readiness to integrate behavioral health and primary care.

PubMed

Scott, Victoria C; Kenworthy, Tara; Godly-Reynolds, Erin; Bastien, Gilberte; Scaccia, Jonathan; McMickens, Courtney; Rachel, Sharon; Cooper, Sayon; Wrenn, Glenda; Wandersman, Abraham

2017-01-01

Integration of behavioral health and primary care services is a promising approach for reducing health disparities. The growing national emphasis on care coordination has mobilized efforts to integrate behavioral health and primary care services across the United States. These efforts align with broader health care system goals of improving health care quality, health equity, utilization efficiency, and patient outcomes. Drawing from our work on a multiyear integrated care initiative (Integrated Care Leadership Program; ICLP) and an implementation science heuristic for organizational readiness (Readiness = Motivation x General Capacity and Innovation-Specific Capacity; R = MC2), this article describes the development and implementation of a tool to assess organizational readiness for integrated care, referred to as the Readiness for Integrated Care Questionnaire (RICQ). The tool was piloted with 11 health care practices that serve vulnerable, underprivileged populations. Initial results from the RICQ revealed that participating practices were generally high in motivation, innovation-specific capacities, and general capacities at the start of ICLP. Additionally, analyses indicated that practices particularly needed support with increasing staff capacities (general knowledge and skills), improving access to and use of resources, and simplifying the steps in integrating care so the effort appears less daunting and difficult to health care team members. We discuss insights from the initial use of RICQ and practical implications of the new tool for driving integrated care efforts that can contribute to health equity. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Functional properties of myoglobins from five whale species with different diving capacities.

PubMed

Helbo, Signe; Fago, Angela

2012-10-01

Whales show an exceptionally wide range of diving capabilities and many express high amounts of the O(2) carrier protein myoglobin (Mb) in their muscle tissues, which increases their aerobic diving capacity. Although previous studies have mainly focused on the muscle Mb concentration and O(2) carrying capacity as markers of diving behavior in whales, it still remains unexplored whether whale Mbs differ in their O(2) affinities and nitrite reductase and peroxidase enzymatic activities, all functions that could contribute to differences in diving capacities. In this study, we have measured the functional properties of purified Mbs from five toothed whales and two baleen whales and have examined their correlation with average dive duration. Results showed that some variation in functional properties exists among whale Mbs, with toothed whale Mbs having higher O(2) affinities and nitrite reductase activities (similar to those of horse Mb) compared with baleen whale Mbs. However, these differences did not correlate with average dive duration. Instead, a significant correlation was found between whale Mb concentration and average duration and depth of dives, and between O(2) affinity and nitrite reductase activity when including horse Mb. Despite the fact that the functional properties showed little species-specific differences in vitro, they may still contribute to enhancing diving capacity as a result of the increased muscle Mb concentration found in extreme divers. In conclusion, Mb concentration rather than specific functional reactivities may support whale diving performance.

Gas adsorption capacity in an all carbon nanomaterial composed of carbon nanohorns and vertically aligned carbon nanotubes.

PubMed

Puthusseri, Divya; Babu, Deepu J; Okeil, Sherif; Schneider, Jörg J

2017-10-04

Whereas vertically aligned carbon nanotubes (VACNTs) typically show a promising adsorption behavior at high pressures, carbon nanohorns (CNHs) exhibit superior gas adsorption properties in the low pressure regime due to their inherent microporosity. These adsorption characteristics are further enhanced when both materials are opened at their tips. The so prepared composite material allows one to investigate the effect of physical entrapment of CO 2 molecules within the specific adsorption sites of VACNTs composed of opened double walled carbon nanotubes (CNTs) and in specific adsorption sites created by spherically aggregated opened single walled carbon nanohorns. Combining 50 wt% of tip opened CNTs with tip opened CNHs increases the CO 2 adsorption capacity of this material by ∼24% at 30 bar and 298 K compared to opened CNHs alone.

Strengthening healthcare capacity through a responsive, country-specific, training standard: the KITSO AIDS training program's support of Botswana's national antiretroviral therapy rollout.

PubMed

Bussmann, Christine; Rotz, Philip; Ndwapi, Ndwapi; Baxter, Daniel; Bussmann, Hermann; Wester, C William; Ncube, Patricia; Avalos, Ava; Mine, Madisa; Mabe, Elang; Burns, Patricia; Cardiello, Peter; Makhema, Joseph; Marlink, Richard

2008-01-01

In parallel with the rollout of Botswana's national antiretroviral therapy (ART) program, the Botswana Ministry of Health established the KITSO AIDS Training Program by entering into long-term partnerships with the Botswana-Harvard AIDS Institute Partnership for HIV Research and Education and others to provide standardized, country-specific training in HIV/AIDS care. The KITSO training model has strengthened human capacity within Botswana's health sector and been indispensable to successful ART rollout. Through core and advanced training courses and clinical mentoring, different cadres of health care workers have been trained to provide high-quality HIV/AIDS care at all ART sites in the country. Continuous and standardized clinical education will be crucial to sustain the present level of care and successfully address future treatment challenges.

Lithium and sodium adsorption properties of two-dimensional aluminum nitride

NASA Astrophysics Data System (ADS)

Sengupta, Amretashis

2018-09-01

In this work the lithiation and sodiation properties of 2-dimensional (2D) AlN sheets are studied from density functional theory (DFT) simulations. 2D AlN showed theoretical specific capacity of 500.8 and 385.3 mA h g-1, maximum open circuit voltage of 1.49 and 1.86 V and diffusion barriers 0.40 and 0.15 eV, for Li and Na adsorption respectively. The calculations show 2D AlN as a possible alternative as anode material in Li-ion and Na-ion batteries. Further the high specific capacity and small diffusion barriers for Na atoms can make 2D AlN useful in supercapacitors. The change in carrier transport properties due to Li/Na adsorption on monolayer AlN can also be useful in chemical/bio-sensors and nanoelectronics devices.

First-principles study of mixed eldfellite compounds Nax(Fe1/2M1/2) (SO4)2 (x=0-2, M = Mn, Co, Ni): A new family of high electrode potential cathodes for the sodium-ion battery

NASA Astrophysics Data System (ADS)

Ri, Gum-Chol; Choe, Song-Hyok; Yu, Chol-Jun

2018-02-01

Natural abundance of sodium and its similar behavior to lithium triggered recent extensive studies of cost-effective sodium-ion batteries (SIBs) for large-scale energy storage systems. A challenge is to develop electrode materials with a high electrode potential, specific capacity and a good rate capability. In this work we propose mixed eldfellite compounds Nax(Fe1/2M1/2) (SO4)2 (x = 0-2, M = Mn, Co, Ni) as a new family of high electrode potential cathodes of SIBs and present their material properties predicted by first-principles calculations. The structural optimizations show that these materials have significantly small volume expansion rates below 5% upon Na insertion/desertion with negative Na binding energies. Through the electronic structure calculations, we find band insulating properties and hole (and/or electron) polaron hoping as a possible mechanism for the charge transfer. Especially we confirm the high electrode voltages over 4 V with reasonably high specific capacities. We also investigate the sodium ion mobility by estimating plausible diffusion pathways and calculating the corresponding activation barriers, demonstrating the reasonably fast migrations of sodium ions during the operation. Our calculation results indicate that these mixed eldfellite compounds can be suitable materials for high performance SIB cathodes.

Sulfur-infiltrated porous carbon microspheres with controllable multi-modal pore size distribution for high energy lithium-sulfur batteries.

PubMed

Zhao, Cunyu; Liu, Lianjun; Zhao, Huilei; Krall, Andy; Wen, Zhenhai; Chen, Junhong; Hurley, Patrick; Jiang, Junwei; Li, Ying

2014-01-21

Sulfur has received increasing attention as a cathode material for lithium-sulfur (Li-S) batteries due to its high theoretical specific capacity. However, the commercialization of Li-S batteries is limited by the challenges of poor electrical conductivity of sulfur, dissolution of the polysulfide intermediates into the electrolyte, and volume expansion of sulfur during cycling. Herein, we report the fabrication of novel-structured porous carbon microspheres with a controllable multi-modal pore size distribution, i.e., a combination of interconnected micropores, mesopores and macropores. Cathodes made of sulfur infiltrated in such a hierarchical carbon framework provide several advantages: (1) a continuous and high surface area carbon network for enhanced electrical conductivity and high sulfur loading; (2) macropores and large mesopores bridged by small mesopores to provide good electrolyte accessibility and fast Li ion transport and to accommodate volume expansion of sulfur; and (3) small mesopores and micropores to improve carbon/sulfur interaction and to help trap polysulfides. An initial discharge capacity at 1278 mA h g(-1) and capacity retention at 70.7% (904 mA h g(-1)) after 100 cycles at a high rate (1 C) were achieved. The material fabrication process is relatively simple and easily scalable.

Highly Durable Na2V6O16·1.63H2O Nanowire Cathode for Aqueous Zinc-Ion Battery.

PubMed

Hu, Ping; Zhu, Ting; Wang, Xuanpeng; Wei, Xiujuan; Yan, Mengyu; Li, Jiantao; Luo, Wen; Yang, Wei; Zhang, Wencui; Zhou, Liang; Zhou, Zhiqiang; Mai, Liqiang

2018-03-14

Rechargeable aqueous zinc-ion batteries are highly desirable for grid-scale applications due to their low cost and high safety; however, the poor cycling stability hinders their widespread application. Herein, a highly durable zinc-ion battery system with a Na 2 V 6 O 16 ·1.63H 2 O nanowire cathode and an aqueous Zn(CF 3 SO 3 ) 2 electrolyte has been developed. The Na 2 V 6 O 16 ·1.63H 2 O nanowires deliver a high specific capacity of 352 mAh g -1 at 50 mA g -1 and exhibit a capacity retention of 90% over 6000 cycles at 5000 mA g -1 , which represents the best cycling performance compared with all previous reports. In contrast, the NaV 3 O 8 nanowires maintain only 17% of the initial capacity after 4000 cycles at 5000 mA g -1 . A single-nanowire-based zinc-ion battery is assembled, which reveals the intrinsic Zn 2+ storage mechanism at nanoscale. The remarkable electrochemical performance especially the long-term cycling stability makes Na 2 V 6 O 16 ·1.63H 2 O a promising cathode for a low-cost and safe aqueous zinc-ion battery.

Relevance of LiPF6 as Etching Agent of LiMnPO4 Colloidal Nanocrystals for High Rate Performing Li-ion Battery Cathodes.

PubMed

Chen, Lin; Dilena, Enrico; Paolella, Andrea; Bertoni, Giovanni; Ansaldo, Alberto; Colombo, Massimo; Marras, Sergio; Scrosati, Bruno; Manna, Liberato; Monaco, Simone

2016-02-17

LiMnPO4 is an attractive cathode material for the next-generation high power Li-ion batteries, due to its high theoretical specific capacity (170 mA h g(-1)) and working voltage (4.1 V vs Li(+)/Li). However, two main drawbacks prevent the practical use of LiMnPO4: its low electronic conductivity and the limited lithium diffusion rate, which are responsible for the poor rate capability of the cathode. The electronic resistance is usually lowered by coating the particles with carbon, while the use of nanosize particles can alleviate the issues associated with poor ionic conductivity. It is therefore of primary importance to develop a synthetic route to LiMnPO4 nanocrystals (NCs) with controlled size and coated with a highly conductive carbon layer. We report here an effective surface etching process (using LiPF6) on colloidally synthesized LiMnPO4 NCs that makes the NCs dispersible in the aqueous glucose solution used as carbon source for the carbon coating step. Also, it is likely that the improved exposure of the NC surface to glucose facilitates the formation of a conductive carbon layer that is in intimate contact with the inorganic core, resulting in a high electronic conductivity of the electrode, as observed by us. The carbon coated etched LiMnPO4-based electrode exhibited a specific capacity of 118 mA h g(-1) at 1C, with a stable cycling performance and a capacity retention of 92% after 120 cycles at different C-rates. The delivered capacities were higher than those of electrodes based on not etched carbon coated NCs, which never exceeded 30 mA h g(-1). The rate capability here reported for the carbon coated etched LiMnPO4 nanocrystals represents an important result, taking into account that in the electrode formulation 80% wt is made of the active material and the adopted charge protocol is based on reasonable fast charge times.

Morphology-controlled synthesis of self-assembled LiFePO4/C/RGO for high-performance Li-ion batteries.

PubMed

Lin, Mei; Chen, Yuming; Chen, Bolei; Wu, Xiao; Kam, Kifung; Lu, Wei; Chan, Helen Lai Wa; Yuan, Jikang

2014-10-22

Novel architectured LiFePO4 (LFP) that consisted of ordered LFP nanocubes was prepared through a facile hydrothermal method using polyethylene glycol (PEG) as a surfactant. The micro/nanostructured LFP with various morphologies ranging from cube cluster to rugby-like structure was synthesized via controlling the pH values of the precursor. A reasonable assembly process elucidating the formation of the hierarchical structure is also provided based on the experimental results. After a combination of carbon (C) coating and reduced graphene oxide (RGO) wrapping, the obtained LFP/C/RGO composites exhibit enhanced electrochemical performance compared to that of blank LFP synthesized under the same condition. Among as-synthesized cube-cluster-like, dumbbell-like, rod-like, and rugby-like composites, the rugby-like LFP/C/RGO reveal the best electrochemical properties with the discharge specific capacity of ∼150 mA h g(-1) after 100 cycles and a high reversible specific capacity of 152 mA h g(-1) at 0.1 C. The prepared LFP/C/RGO composite can be a promising cathode material for high energy, low cost, and environmentally friendly lithium-ion batteries.

High Capacity Cathode Materials for Next Generation Energy Storage

NASA Astrophysics Data System (ADS)

Papandrea, Benjamin John

Energy storage devices are of increasing importance for applications in mobile electronics, hybrid electric vehicles, and can also play a critical role in renewable energy harvesting, conversion and storage. Since its commercial inception in the 1990's, the lithium-ion battery represents the dominant energy storage technology for mobile power supply today. However, the total capacity of lithium-ion batteries is largely limited by the theoretical capacities of the cathode materials such as LiCoO2 (272 mAh g-1), and LiFePO4 (170 mAh g-1), and cannot satisfy the increasing consumer demand, thus new cathode materials with higher capacities must be explored. Two of the most promising cathode materials with significantly larger theoretical capacities are sulfur (1675 mAh g-1) and air, specifically the oxygen (3840 mAh g-1). However, the usage of either of these cathodic materials is plagued with numerous issues that must be overcome before their commercialization. In the first part of my dissertation, we investigated the usage of a three-dimensional graphene membrane for a high energy density lithium-air (Li-Air) battery in ambient condition. One of the issues with Li-Air batteries is the many side reaction that can occur during discharge in ambient condition, especially with water vapor. Using a hydrophobic tortuous three-dimensional graphene membrane we are able to inhibit the diffusion of water vapor and create a lithium-air battery that cycles over 2000 times with a capacity limited at 140 mAh g-1, over 100 cycles with a capacity limited at 1425 mAh g-1, and over 20 cycles at the high capacity of 5700 mAh g-1. In the second part of my dissertation, we investigate the usage of a three-dimensional graphene aerogel to maximize the loading of sulfur to create a freestanding electrode with high capacity for a lithium-sulfur (Li-S) battery. We demonstrated that our three-dimensional graphene aerogel could sustain a loading of 95% by weight, and we achieved a capacity of 969 mAh g-1 normalized by the entire electrode with a 90% sulfur loading. In the third and final part of my dissertation, we investigate the usage of catalysts for both Li-Air, and Li-S batteries. We demonstrate how different noble metal configurations are optimal for Li-Air batteries, showcase how different metals effect the sulfur reduction reaction, and how both Pt and Mn increase the capacity of Li-S battery by interacting with the sulfur redox reactions intermediate species.

Porous Co3O4 nanorods anchored on graphene nanosheets as an effective electrocatalysts for aprotic Li-O2 batteries

NASA Astrophysics Data System (ADS)

Yuan, Mengwei; Yang, Yan; Nan, Caiyun; Sun, Genban; Li, Huifeng; Ma, Shulan

2018-06-01

The large over-potential during the battery operation is a great obstacle for the application of Li-O2 batteries. The porous structure and electrical conductivity of the electrocatalysts are significant for the electrocatalytic performance of Li-O2 batteries. In this work, a porous Co3O4/GN nanocomposite (Co3O4 nanorods anchored on graphene nanosheets) is prepared via a facile hydrothermal method assisted with heat treatment. The unique structure of Co3O4/GN endows efficient electrocatalystic activity for Li-O2 batteries. In comparison to the Co3O4, the Co3O4/GN demonstrates a better cycle performance showing more than 40 cycles with a 1500 mAh g-1 capacity limit strategy at a current density of 300 mA g-1, and a reduced over-potential of 110 mV at high current density (1200 mA g-1). The Co3O4/GN also displays a high initial specific capacity (7600 mAh g-1) and a good reversibility in full cycle with a coulombic efficiency of 99.8% in the first cycle. The impressed cyclability, specific capacity, rate performance, and low over-potentials indicate that the as-prepared Co3O4/GN nanocomposite is a promising catalyst candidate for reversible Li-O2 batteries.

Enhanced electrochemical properties of F-doped Li2MnSiO4/C for lithium ion batteries

NASA Astrophysics Data System (ADS)

Wang, Chao; Xu, Youlong; Sun, Xiaofei; Zhang, Baofeng; Chen, Yanjun; He, Shengnan

2018-02-01

The Li2MnSiO4 as a novel cathode material for lithium ion batteries, performs high specific capacity, high thermal stability, low cost and etc. However, it suffers from relatively low electronic conductivity and lithium ion diffusion rate. Herein, we successfully introduce fluorine to Li2MnSiO4 (Li2MnSiO4-xFx, x = 0.00, 0.01, 0.03 and 0.05) to overcome these obstacles. The results show that F doping not only enlarges the lattice parameters but also decreases the particle size, synergistically improving the lithium ion diffusion of Li2MnSiO4. Moreover, F doping increase electronic conductivity of Li2MnSiO4/C by inhibiting the formation of C-O bonds in the carbon layers. Meanwhile, F doping improves the crystallinity and stabilizes the crystal structure of Li2MnSiO4. Finally, the Li2MnSiO3.97F0.03/C with the best electrochemical performances delivers the initial specific discharge capacity of 279 mA h g-1 at 25mA g-1 current density from 1.5 V to 4.8 V. Also, it maintains a higher capacity (201 mA h g-1) than F-free Li2MnSiO4 (145 mA h g-1) after 50 cycles.

One-step electrodeposition of Co0·12Ni1·88S2@Co8S9 nanoparticles on highly conductive TiO2 nanotube arrays for battery-type electrodes with enhanced energy storage performance

NASA Astrophysics Data System (ADS)

Yu, Cuiping; Wang, Yan; Zhang, Jianfang; Yang, Wanfen; Shu, Xia; Qin, Yongqiang; Cui, Jiewu; Zheng, Hongmei; Zhang, Yong; Ajayan, Pulickel M.; Wu, Yucheng

2017-10-01

High-performance battery-type electrodes based on TiO2 nanotube arrays decorated with Co0·12Ni1·88S2@Co8S9 (CNCS) nanoparticles have been successfully prepared in this paper. The highly conductive TiO2 nanotube arrays modified with carbon and oxygen vacancies (Ti3+ defects) (m-TNAs) are selected as the three-dimensional backbones to support electroactive materials and offer direct pathways for electron and ions transport. Then CNCS nanoparticles are electrodeposited on each nanotube uniformly, and the loading mass of nanoparticles can be controlled through adjusting electrodeposition cycles. After optimization, a remarkable specific capacity of 680.1 C g-1 is achieved at 2 A g -1 as a result of the intrinsic synergetic contributions from structural/compositional/componental merits. This specific capacity is much higher than most of the TNAs-based energy storage electrodes. In addition, an asymmetric supercapacitor device is assembled by applying the optimized CNCS/m-TNAs and commercial active carbon as positive and negative electrode, respectively. It displays a high energy density of 45.5 Wh kg-1 at a power density of 400.5 W kg-1, after cycling for 3000 cycles at a high current density of 4 A g-1, the specific capacitance could still remain 85.7%. This self-supported and binder-free CNCS/m-TNAs electrode will be a competitive and promising candidate for the application in energy storage.

High-capacity cathodes for lithium-ion batteries from nanostructured LiFePO4 synthesized by highly-flexible and scalable flame spray pyrolysis

NASA Astrophysics Data System (ADS)

Hamid, N. A.; Wennig, S.; Hardt, S.; Heinzel, A.; Schulz, C.; Wiggers, H.

2012-10-01

Olivine, LiFePO4 is a promising cathode material for lithium-ion batteries due to its low cost, environmental acceptability and high stability. Its low electric conductivity prevented it for a long time from being used in large-scale applications. Decreasing its particle size along with carbon coating significantly improves electronic conductivity and lithium diffusion. With respect to the controlled formation of very small particles with large specific surface, gas-phase synthesis opens an economic and flexible route towards high-quality battery materials. Amorphous FePO4 was synthesized as precursor material for LiFePO4 by flame spray pyrolysis of a solution of iron acetylacetonate and tributyl phosphate in toluene. The pristine FePO4 with a specific surface from 126-218 m2 g-1 was post-processed to LiFePO4/C composite material via a solid-state reaction using Li2CO3 and glucose. The final olivine LiFePO4/C particles still showed a large specific surface of 24 m2 g-1 and were characterized using X-ray diffraction (XRD), electron microscopy, X-ray photoelectron spectrocopy (XPS) and elemental analysis. Electrochemical investigations of the final LiFePO4/C composites show reversible capacities of more than 145 mAh g-1 (about 115 mAh g-1 with respect to the total coating mass). The material supports high drain rates at 16 C while delivering 40 mAh g-1 and causes excellent cycle stability.

Achieving high peak capacity production for gas chromatography and comprehensive two-dimensional gas chromatography by minimizing off-column peak broadening.

PubMed

Wilson, Ryan B; Siegler, W Christopher; Hoggard, Jamin C; Fitz, Brian D; Nadeau, Jeremy S; Synovec, Robert E

2011-05-27

By taking into consideration band broadening theory and using those results to select experimental conditions, and also by reducing the injection pulse width, peak capacity production (i.e., peak capacity per separation time) is substantially improved for one dimensional (1D-GC) and comprehensive two dimensional (GC×GC) gas chromatography. A theoretical framework for determining the optimal linear gas velocity (the linear gas velocity producing the minimum H), from experimental parameters provides an in-depth understanding of the potential for GC separations in the absence of extra-column band broadening. The extra-column band broadening is referred to herein as off-column band broadening since it is additional band broadening not due to the on-column separation processes. The theory provides the basis to experimentally evaluate and improve temperature programmed 1D-GC separations, but in order to do so with a commercial 1D-GC instrument platform, off-column band broadening from injection and detection needed to be significantly reduced. Specifically for injection, a resistively heated transfer line is coupled to a high-speed diaphragm valve to provide a suitable injection pulse width (referred to herein as modified injection). Additionally, flame ionization detection (FID) was modified to provide a data collection rate of 5kHz. The use of long, relatively narrow open tubular capillary columns and a 40°C/min programming rate were explored for 1D-GC, specifically a 40m, 180μm i.d. capillary column operated at or above the optimal average linear gas velocity. Injection using standard auto-injection with a 1:400 split resulted in an average peak width of ∼1.5s, hence a peak capacity production of 40peaks/min. In contrast, use of modified injection produced ∼500ms peak widths for 1D-GC, i.e., a peak capacity production of 120peaks/min (a 3-fold improvement over standard auto-injection). Implementation of modified injection resulted in retention time, peak width, peak height, and peak area average RSD%'s of 0.006, 0.8, 3.4, and 4.0%, respectively. Modified injection onto the first column of a GC×GC coupled with another high-speed valve injection onto the second column produced an instrument with high peak capacity production (500-800peaks/min), ∼5-fold to 8-fold higher than typically reported for GC×GC. Copyright © 2011 Elsevier B.V. All rights reserved.

Container System Hardware Status Report 1990

DTIC Science & Technology

1990-01-01

class high - speed containerships and their subsequent conversion to a cargo configuration specifically designed for rapid load/unload of military...pump modules though it could be used for general cargo and organizational property. STATUS A procurement contract for 402 shipping frames was conducted...for various cargo heights. The second type of flatrack has a maximum cargo capacity of 72 short-tons and has comer posts 13 feet high . The comer posts

Hierarchical porous NiCo2O4 nanowires for high-rate supercapacitors.

PubMed

Jiang, Hao; Ma, Jan; Li, Chunzhong

2012-05-11

We demonstrate a simple and scalable strategy for synthesizing hierarchical porous NiCo(2)O(4) nanowires which exhibit a high specific capacitance of 743 F g(-1) at 1 A g(-1) with excellent rate performance (78.6% capacity retention at 40 A g(-1)) and cycling stability (only 6.2% loss after 3000 cycles). This journal is © The Royal Society of Chemistry 2012

Device and method for enhanced collection and assay of chemicals with high surface area ceramic

DOEpatents

Addleman, Raymond S.; Li, Xiaohong Shari; Chouyyok, Wilaiwan; Cinson, Anthony D.; Bays, John T.; Wallace, Krys

2016-02-16

A method and device for enhanced capture of target analytes is disclosed. This invention relates to collection of chemicals for separations and analysis. More specifically, this invention relates to a solid phase microextraction (SPME) device having better capability for chemical collection and analysis. This includes better physical stability, capacity for chemical collection, flexible surface chemistry and high affinity for target analyte.

Room-Temperature Solution Synthesis of Mesoporous Silicon for Lithium Ion Battery Anodes.

PubMed

Sun, Lin; Wang, Fei; Su, Tingting; Du, Hongbin

2017-11-22

As an important optoelectronic and energy-storage material, porous silicon (PSi) has attracted great interest in various fields. The preparation of PSi, however, usually suffers from low yields and/or complicated syntheses. Herein, we report a facile solution method to prepare PSi with controllable high specific surface area. Commercial Zintl compound Mg 2 Si readily reacts with HSiCl 3 in the presence of amines at room temperature to produce amorphous PSi in high yields, where in situ formed salt byproducts serve as templates to generate uniform mesopores of ca. 3.8 nm in diameter. After crystallization treatment at 700 °C in flow Ar gas for 40 min, the obtained crystalline PSi coated with carbon layers shows excellent electrochemical performance when served as lithium ion battery anodes. The reversible specific capacity is about 2250 mA h g -1 at 0.1 A g -1 and the capacity retention is maintained at 90% after cycling at high current density of 2 A g -1 for 320 times. This simple, facile preparation method is very promising and paves the way for massive production of porous Si as high-performance anodes in Li-ion battery industry or for other applications, such as drug delivery systems and catalysis.

Porous, Hyper-cross-linked, Three-Dimensional Polymer as Stable, High Rate Capability Electrode for Lithium-Ion Battery.

PubMed

Mukherjee, Debdyuti; Gowda Y K, Guruprasada; Makri Nimbegondi Kotresh, Harish; Sampath, S

2017-06-14

Organic materials containing active carbonyl groups have attracted considerable attention as electrodes in Li-ion batteries due to their reversible redox activity, ability to retain capacity, and, in addition, their ecofriendly nature. Introduction of porosity will help accommodate as well as store small ions and molecules reversibly. In the present work, we introduce a mesoporous triptycene-related, rigid network polymer with high specific surface area as an electrode material for rechargeable Li-ion battery. The designed polymer with a three-dimensional (3D), rigid porous network allows free movement of ions/electrolyte as well as helps in interacting with the active anhydride moieties (containing two carbonyl groups). Considerable intake of Li + ions giving rise to very high specific capacity of 1100 mA h g -1 at a discharge current of 50 mA g -1 and ∼120 mA h g -1 at a high discharge current of 3 A g -1 are observed with excellent cyclability up to 1000 cycles. This remarkable rate capability, which is one of the highest among the reported organic porous polymers to date, makes the triptycene-related rigid 3D network a very good choice for Li-ion batteries and opens up a new method to design polymer-based electrode materials for metal-ion battery technology.

Determination of Specific Heat Capacity on Composite Shape-Stabilized Phase Change Materials and Asphalt Mixtures by Heat Exchange System

PubMed Central

Ma, Biao; Zhou, Xue-yan; Liu, Jiang; You, Zhanping; Wei, Kun; Huang, Xiao-feng

2016-01-01

Previous research has shown that composite shape-stabilized phase change material (CPCM) has a remarkable capacity for thermal storage and stabilization, and it can be directly applied to highway construction without leakage. However, recent studies on temperature changing behaviors of CPCM and asphalt mixture cannot intuitively reflect the thermoregulation mechanism and efficiency of CPCM on asphalt mixture. The objective of this paper is to determine the specific heat capacity of CPCM and asphalt mixtures mixed with CPCM using the heat exchange system and the data acquisition system. Studies have shown that the temperature-rise curve of 5 °C CPCM has an obvious temperature plateau, while an asphalt mixture mixed with 5 °C CPCM does not; with increasing temperature, the specific heat capacities of both 5 °C CPCM and asphalt mixture first increase and then decrease, while the variation rate of 5 °C CPCM is larger than that of the asphalt mixture, and the maximum specific heat capacity of 5 °C CPCM appears around the initial phase change temperature. It is concluded that the temperature intervals of 5 °C CPCM are −18 °C–7 °C, 7 °C–25 °C and 25 °C–44 °C, respectively, and that of the asphalt mixture are −18 °C~10 °C, −10 °C~5 °C and 5 °C~28 °C. A low dosage of 5 °C CPCM has little influence on the specific heat capacity of asphalt mixture. Finally, the functions of specific heat capacities and temperature for CPCM and asphalt mixture mixed with CPCM were recommended by the sectional regression method. PMID:28773510

Determination of Specific Heat Capacity on Composite Shape-Stabilized Phase Change Materials and Asphalt Mixtures by Heat Exchange System.

PubMed

Ma, Biao; Zhou, Xue-Yan; Liu, Jiang; You, Zhanping; Wei, Kun; Huang, Xiao-Feng

2016-05-19

Previous research has shown that composite shape-stabilized phase change material (CPCM) has a remarkable capacity for thermal storage and stabilization, and it can be directly applied to highway construction without leakage. However, recent studies on temperature changing behaviors of CPCM and asphalt mixture cannot intuitively reflect the thermoregulation mechanism and efficiency of CPCM on asphalt mixture. The objective of this paper is to determine the specific heat capacity of CPCM and asphalt mixtures mixed with CPCM using the heat exchange system and the data acquisition system. Studies have shown that the temperature-rise curve of 5 °C CPCM has an obvious temperature plateau, while an asphalt mixture mixed with 5 °C CPCM does not; with increasing temperature, the specific heat capacities of both 5 °C CPCM and asphalt mixture first increase and then decrease, while the variation rate of 5 °C CPCM is larger than that of the asphalt mixture, and the maximum specific heat capacity of 5 °C CPCM appears around the initial phase change temperature. It is concluded that the temperature intervals of 5 °C CPCM are -18 °C-7 °C, 7 °C-25 °C and 25 °C-44 °C, respectively, and that of the asphalt mixture are -18 °C~10 °C, -10 °C~5 °C and 5 °C~28 °C. A low dosage of 5 °C CPCM has little influence on the specific heat capacity of asphalt mixture. Finally, the functions of specific heat capacities and temperature for CPCM and asphalt mixture mixed with CPCM were recommended by the sectional regression method.

Effect of Specific Growth Rate on Fermentative Capacity of Baker’s Yeast

PubMed Central

Van Hoek, Pim; Van Dijken, Johannes P.; Pronk, Jack T.

1998-01-01

The specific growth rate is a key control parameter in the industrial production of baker’s yeast. Nevertheless, quantitative data describing its effect on fermentative capacity are not available from the literature. In this study, the effect of the specific growth rate on the physiology and fermentative capacity of an industrial Saccharomyces cerevisiae strain in aerobic, glucose-limited chemostat cultures was investigated. At specific growth rates (dilution rates, D) below 0.28 h−1, glucose metabolism was fully respiratory. Above this dilution rate, respirofermentative metabolism set in, with ethanol production rates of up to 14 mmol of ethanol · g of biomass−1 · h−1 at D = 0.40 h−1. A substantial fermentative capacity (assayed offline as ethanol production rate under anaerobic conditions) was found in cultures in which no ethanol was detectable (D < 0.28 h−1). This fermentative capacity increased with increasing dilution rates, from 10.0 mmol of ethanol · g of dry yeast biomass−1 · h−1 at D = 0.025 h−1 to 20.5 mmol of ethanol · g of dry yeast biomass−1 · h−1 at D = 0.28 h−1. At even higher dilution rates, the fermentative capacity showed only a small further increase, up to 22.0 mmol of ethanol · g of dry yeast biomass−1 · h−1 at D = 0.40 h−1. The activities of all glycolytic enzymes, pyruvate decarboxylase, and alcohol dehydrogenase were determined in cell extracts. Only the in vitro activities of pyruvate decarboxylase and phosphofructokinase showed a clear positive correlation with fermentative capacity. These enzymes are interesting targets for overexpression in attempts to improve the fermentative capacity of aerobic cultures grown at low specific growth rates. PMID:9797269

DOE Office of Scientific and Technical Information (OSTI.GOV)

Xu, Gui-Liang; Chen, Zonghai; Zhong, Gui-Ming

Sodium-ion batteries are promising alternatives to lithium-ion batteries for large-scale applications. However, the low capacity and poor rate capability of existing anodes for sodium-ion batteries are bottlenecks for future developments. Here, we report a high performance nanostructured anode material for sodium-ion batteries that is fabricated by high energy ball milling to form black phosphorus/Ketjenblack–multiwalled carbon nanotubes (BPC) composite. With this strategy, the BPC composite with a high phosphorus content (70 wt %) could deliver a very high initial Coulombic efficiency (>90%) and high specific capacity with excellent cyclability at high rate of charge/discharge (~1700 mAh g–1 after 100 cycles atmore » 1.3 A g–1 based on the mass of P). In situ electrochemical impedance spectroscopy, synchrotron high energy X-ray diffraction, ex situ small/wide-angle X-ray scattering, high resolution transmission electronic microscopy, and nuclear magnetic resonance were further used to unravel its superior sodium storage performance. The scientific findings gained in this work are expected to serve as a guide for future design on high performance anode material for sodium-ion batteries.« less

A facile approach to nanoarchitectured three-dimensional graphene-based Li-Mn-O composite as high-power cathodes for Li-ion batteries.

PubMed

Zhang, Wenyu; Zeng, Yi; Xu, Chen; Xiao, Ni; Gao, Yiben; Li, Lain-Jong; Chen, Xiaodong; Hng, Huey Hoon; Yan, Qingyu

2012-01-01

We report a facile method to prepare a nanoarchitectured lithium manganate/graphene (LMO/G) hybrid as a positive electrode for Li-ion batteries. The Mn(2)O(3)/graphene hybrid is synthesized by exfoliation of graphene sheets and deposition of Mn(2)O(3) in a one-step electrochemical process, which is followed by lithiation in a molten salt reaction. There are several advantages of using the LMO/G as cathodes in Li-ion batteries: (1) the LMO/G electrode shows high specific capacities at high gravimetric current densities with excellent cycling stability, e.g., 84 mAh·g(-1) during the 500th cycle at a discharge current density of 5625 mA·g(-1) (~38.01 C capacity rating) in the voltage window of 3-4.5 V; (2) the LMO/G hybrid can buffer the Jahn-Teller effect, which depicts excellent Li storage properties at high current densities within a wider voltage window of 2-4.5 V, e.g., 93 mAh·g(-1) during the 300th cycle at a discharge current density of 5625 mA·g(-1) (~38.01 C). The wider operation voltage window can lead to increased theoretical capacity, e.g., 148 mAh·g(-1) between 3 and 4.5 V and 296 mAh·g(-1) between 2 and 4.5 V; (3) more importantly, it is found that the attachment of LMO onto graphene can help to reduce the dissolution of Mn(2+) into the electrolyte, as indicated by the inductively coupled plasma (ICP) measurements, and which is mainly attributed to the large specific surface area of the graphene sheets.

Topology of genetic associations between regional gray matter volume and intellectual ability: Evidence for a high capacity network.

PubMed

Bohlken, Marc M; Brouwer, Rachel M; Mandl, René C W; Hedman, Anna M; van den Heuvel, Martijn P; van Haren, Neeltje E M; Kahn, René S; Hulshoff Pol, Hilleke E

2016-01-01

Intelligence is associated with a network of distributed gray matter areas including the frontal and parietal higher association cortices and primary processing areas of the temporal and occipital lobes. Efficient information transfer between gray matter regions implicated in intelligence is thought to be critical for this trait to emerge. Genetic factors implicated in intelligence and gray matter may promote a high capacity for information transfer. Whether these genetic factors act globally or on local gray matter areas separately is not known. Brain maps of phenotypic and genetic associations between gray matter volume and intelligence were made using structural equation modeling of 3T MRI T1-weighted scans acquired in 167 adult twins of the newly acquired U-TWIN cohort. Subsequently, structural connectivity analyses (DTI) were performed to test the hypothesis that gray matter regions associated with intellectual ability form a densely connected core. Gray matter regions associated with intellectual ability were situated in the right prefrontal, bilateral temporal, bilateral parietal, right occipital and subcortical regions. Regions implicated in intelligence had high structural connectivity density compared to 10,000 reference networks (p=0.031). The genetic association with intelligence was for 39% explained by a genetic source unique to these regions (independent of total brain volume), this source specifically implicated the right supramarginal gyrus. Using a twin design, we show that intelligence is genetically represented in a spatially distributed and densely connected network of gray matter regions providing a high capacity infrastructure. Although genes for intelligence have overlap with those for total brain volume, we present evidence that there are genes for intelligence that act specifically on the subset of brain areas that form an efficient brain network. Copyright © 2015 Elsevier Inc. All rights reserved.

Self-assembled mesoporous TiO2/carbon nanotube composite with a three-dimensional conducting nanonetwork as a high-rate anode material for lithium-ion battery

NASA Astrophysics Data System (ADS)

Wang, Jie; Ran, Ran; Tade, Moses O.; Shao, Zongping

2014-05-01

Mesoporous three-dimensional (3D) TiO2/carbon nanotube conductive hybrid nanostructures can be successfully developed using polyethylene oxide (PEO) to modify the surfaces of carbon nanotubes (CNTs). During the synthesis process, PEO acts as not only "bridges" to connect the TiO2 nanoparticles to the CNT surfaces but also as "hosts" to accommodate and stabilize the in situ generated TiO2 particles. As the electrodes for lithium-ion batteries, such mesoporous 3D TiO2/CNT hybrids, demonstrate high Li storage capacity, superior rate performance and excellent long-term cycling stability. They exhibit a reversible specific capacity of 203 mA h g-1 at 100 mA g-1 and a stable capacity retention of 91 mA h g-1 at 8000 mA g-1 (47.6 C) over 100 cycles; they also retain approximately 90% (71 mA h g-1) of their initial discharge capacity after 900 cycles at an extremely high rate of 15,000 mA g-1 (89 C). This facile synthetic strategy to construct mesoporous 3D TiO2/CNT conductive hybrids provides a convenient route that efficiently assembles various inorganic oxide components on the CNTs' surfaces and enables the formation of heterogeneous nanostructures with novel functionalities. In particular, utilizing a conductive 3D CNT network can serve as a promising strategy for developing high-performance electrodes for Li secondary batteries and supercapacitors.

Construction of hierarchical porous NiCo{sub 2}O{sub 4} films composed of nanowalls as cathode materials for high-performance supercapacitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zheng, Qingyun, E-mail: hizhengqingyun@126.com; Zhang, Xiangyang; Shen, Youming

Graphical abstract: Hydrothermal-synthesized NiCo{sub 2}O{sub 4} mesowall films exhibit porous structure and high capacity as well as good cycling life for supercapacitor application. - Highlights: • Hierarchical porous NiCo{sub 2}O{sub 4} nanowall films are prepared by a hydrothermal method. • NiCo{sub 2}O{sub 4} nanowall films show excellent electrochemical performance. • Hierarchical porous film structure is favorable for fast ion/electron transfer. - Abstract: Hierarchical porous NiCo{sub 2}O{sub 4} films composed of nanowalls on nickel foam are synthesized via a facile hydrothermal method. Besides the mesoporous walls, the NiCo{sub 2}O{sub 4} nanowalls are interconnected with each other to form hierarchical porous structure.more » These unique porous structured films possess a high specific surface area. The supercapacitor performance of the hierarchical porous NiCo{sub 2}O{sub 4} film is fully characterized. A high capacity of 130 mA h g{sup −1} is achieved at 2 A g{sup −1} with 97% capacity maintained after 2,000 cycles. Importantly, 75.6% of capacity is retained when the current density changes from 3 A g{sup −1} to 36 A g{sup −1}. The superior electrochemical performance is mainly due to the unique hierarchical porous structure with large surface area as well as shorter diffusion length for ion and charge transport.« less

The presence of high-affinity, low-capacity estradiol-17β binding in rainbow trout scale indicates a possible endocrine route for the regulation of scale resorption

USGS Publications Warehouse

Persson, Petra; Shrimpton, J. Mark; McCormick, Stephen D.; Bjornsson, Bjorn Thrandur

2000-01-01

High-affinity, low-capacity estradiol-17β (E2) binding is present in rainbow trout scale. The Kd and Bmax of the scale E2 binding are similar to those of the liver E2 receptor (Kd is 1.6 ± 0.1 and 1.4 ± 0.1 nM, and Bmax is 9.1 ± 1.2 and 23.1 ± 2.2 fmol × mg protein-1, for scale and liver, respectively), but different from those of the high-affinity, low-capacity E2 binding in plasma (Kd is 4.0 ± 0.4 nM and Bmax is 625.4 ± 63.1 fmol × mg protein−1). The E2 binding in scale was displaced by testosterone, but not by diethylstilbestrol. Hence, the ligand binding specificity is different from that of the previously characterized liver E2 receptor, where E2 is displaced by diethylstilbestrol, but not by testosterone. The putative scale E2 receptor thus appears to bind both E2 and testosterone, and it is proposed that the increased scale resorption observed during sexual maturation in both sexes of several salmonid species may be mediated by this receptor. No high-affinity, low-capacity E2 binding could be detected in rainbow trout gill or skin.

Experimental investigation of refractory metals in the premelting region during fast heating

NASA Astrophysics Data System (ADS)

Senchenko, V. N.; Belikov, R. S.; Popov, V. S.

2015-11-01

This work demonstrates experimental possibility of investigation of high refractory materials around its melting point, particularly in premelting region with high accuracy. In this article authors describe the developed experimental setup based on rapid resistive self-heating of a sample by a large current pulse generated by a capacitor discharge circuit that allow fast pulse interruption by temperature feedback signal. The sample temperature was measured with a two-channel microsecond radiation pyrometer. Preliminary experiments were conducted on tantalum and molybdenum at heating speed of 108 K/s. The method allows investigating thermophysical properties of refractory conductive materials such as melting temperature, melting heat, specific resistivity, specific enthalpy and specific heat capacity in solid and liquid phase, especially in premelting area.

Glassy Metal Alloy Nanofiber Anodes Employing Graphene Wrapping Layer: Toward Ultralong-Cycle-Life Lithium-Ion Batteries.

PubMed

Jung, Ji-Won; Ryu, Won-Hee; Shin, Jungwoo; Park, Kyusung; Kim, Il-Doo

2015-07-28

Amorphous silicon (a-Si) has been intensively explored as one of the most attractive candidates for high-capacity and long-cycle-life anode in Li-ion batteries (LIBs) primarily because of its reduced volume expansion characteristic (∼280%) compared to crystalline Si anodes (∼400%) after full Li(+) insertion. Here, we report one-dimensional (1-D) electrospun Si-based metallic glass alloy nanofibers (NFs) with an optimized composition of Si60Sn12Ce18Fe5Al3Ti2. On the basis of careful compositional tailoring of Si alloy NFs, we found that Ce plays the most important role as a glass former in the formation of the metallic glass alloy. Moreover, Si-based metallic glass alloy NFs were wrapped by reduced graphene oxide sheets (specifically Si60Sn12Ce18Fe5Al3Ti2 NFs@rGO), which can prevent the direct exposure of a-Si alloy NFs to the liquid electrolyte and stabilize the solid-electrolyte interphase (SEI) layers on the surfaces of rGO sheets while facilitating electron transport. The metallic glass nanofibers exhibited superior electrochemical cell performance as an anode: (i) Si60Sn12Ce18Fe5Al3Ti2 NFs show a high specific capacity of 1017 mAh g(-1) up to 400 cycles at 0.05C with negligible capacity loss as well as superior cycling performance (nearly 99.9% capacity retention even after 2000 cycles at 0.5C); (ii) Si60Sn12Ce18Fe5Al3Ti2 NFs@rGO reveals outstanding rate behavior (569.77 mAh g(-1) after 2000 cycles at 0.5C and a reversible capacity of around 370 mAh g(-1) at 4C). We demonstrate the potential suitability of multicomponent a-Si alloy NFs as a long-cycling anode material.

Evaluation of predictive capacities of biomarkers based on research synthesis.

PubMed

Hattori, Satoshi; Zhou, Xiao-Hua

2016-11-10

The objective of diagnostic studies or prognostic studies is to evaluate and compare predictive capacities of biomarkers. Suppose we are interested in evaluation and comparison of predictive capacities of continuous biomarkers for a binary outcome based on research synthesis. In analysis of each study, subjects are often classified into two groups of the high-expression and low-expression groups according to a cut-off value, and statistical analysis is based on a 2 × 2 table defined by the response and the high expression or low expression of the biomarker. Because the cut-off is study specific, it is difficult to interpret a combined summary measure such as an odds ratio based on the standard meta-analysis techniques. The summary receiver operating characteristic curve is a useful method for meta-analysis of diagnostic studies in the presence of heterogeneity of cut-off values to examine discriminative capacities of biomarkers. We develop a method to estimate positive or negative predictive curves, which are alternative to the receiver operating characteristic curve based on information reported in published papers of each study. These predictive curves provide a useful graphical presentation of pairs of positive and negative predictive values and allow us to compare predictive capacities of biomarkers of different scales in the presence of heterogeneity in cut-off values among studies. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Attachment-inducing capacities of fish skin epithelial extracts on oncomiracidia of Benedenia seriolae (Monogenea: Capsalidae).

PubMed

Yoshinaga, Tomoyoshi; Nagakura, Tatsuhiro; Ogawa, Kazuo; Fukuda, Yutaka; Wakabayashi, Hisatsugu

2002-03-01

Attachment-inducing capacities of skin epithelial extracts of yellowtail, Japanese flounder and red sea bream on oncomiracidia of the monogenean Benedenia seriolae were examined. Clear differences were not detected in the capacity among the fish species, although B. seriolae infects only yellowtail and its congeners in Seriola. This suggests that either the capacity is not host specific or host-specific attachment-inducing capacity cannot be detected by the assay method. Further, the attachment-inducing capacities were suppressed by wheat-germ lectin and concanavalin A in skin epithelial extracts of Japanese flounder and yellowtail, respectively. This suggests that some sugar-related chemical substances existing in fish epithelia induce the attachment of B. seriolae oncomiracidia.

Si/Ti2O3/Reduced Graphene Oxide Nanocomposite Anodes for Lithium-Ion Batteries with Highly Enhanced Cyclic Stability.

PubMed

Park, A Reum; Son, Dae-Yong; Kim, Jung Sub; Lee, Jun Young; Park, Nam-Gyu; Park, Juhyun; Lee, Joong Kee; Yoo, Pil J

2015-08-26

Silicon (Si) has attracted tremendous attention as a high-capacity anode material for next generation Li-ion batteries (LIBs); unfortunately, it suffers from poor cyclic stability due to excessive volume expansion and reduced electrical conductivity after repeated cycles. To circumvent these issues, we propose that Si can be complexed with electrically conductive Ti2O3 to significantly enhance the reversible capacity and cyclic stability of Si-based anodes. We prepared a ternary nanocomposite of Si/Ti2O3/reduced graphene oxide (rGO) using mechanical blending and subsequent thermal reduction of the Si, TiO2 nanoparticles, and rGO nanosheets. As a result, the obtained ternary nanocomposite exhibited a specific capacity of 985 mAh/g and a Coulombic efficiency of 98.4% after 100 cycles at a current density of 100 mA/g. Furthermore, these ternary nanocomposite anodes exhibited outstanding rate capability characteristics, even with an increased current density of 10 A/g. This excellent electrochemical performance can be ascribed to the improved electron and ion transport provided by the Ti2O3 phase within the Si domains and the structurally reinforced conductive framework comprised of the rGO nanosheets. Therefore, it is expected that our approach can also be applied to other anode materials to enable large reversible capacity, excellent cyclic stability, and good rate capability for high-performance LIBs.

Fabrication and lithium storage performance of sugar apple-shaped SiOx@C nanocomposite spheres

NASA Astrophysics Data System (ADS)

Li, Mingqi; Zeng, Ying; Ren, Yurong; Zeng, Chunmei; Gu, Jingwei; Feng, Xiaofang; He, Hongyan

2015-08-01

Nonstoichiometric SiOx is a kind of very attractive anode material for high-energy lithium-ion batteries because of a high specific capacity and facile synthesis. However, the poor electrical conductivity and unstable electrode structure of SiOx severely limit its electrochemical performance as anode in lithium-ion batteries. In this work, highly durable sugar apple-shaped SiOx@C nanocomposite spheres are fabricated to achieve significantly improved electrochemical performance. The composite is synthesized by homogenous one-pot synthesis, using ethyltriethoxysilanes (EtSi(OEt)3) and resorcinol/formaldehyde (RF) as starting materials. The morphology, composition and structure of the composite are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), elemental analysis (EA) and X-ray photoelectron spectroscopy (XPS). At a current density of 50 mA g-1, the sugar apple-shaped SiOx@C spheres exhibit a stable discharge capacity of about 630 mAh g-1 calculated on the total mass of both SiOx and C. At a current density of 100 mA g-1, a stable discharge capacity of about 550 mAh g-1 is obtained and the capacity has been kept up to 400 cycles. The excellent cycling performance is attributed to the homogeneous dispersion of SiOx in disordered carbon at the nanometer scale and the unique structure of the composite.

34 CFR 222.171 - What LEAs may be eligible for Discretionary Construction grants?

Code of Federal Regulations, 2013 CFR

2013-07-01

...) Meet the specific numeric requirements regarding bonding capacity. (2) The Secretary must also consider... students; or (v) Meet the specific numeric requirements regarding bonding capacity. (2) The Secretary must...

Effects of Age and Working Memory Capacity on Speech Recognition Performance in Noise Among Listeners With Normal Hearing.

PubMed

Gordon-Salant, Sandra; Cole, Stacey Samuels

2016-01-01

This study aimed to determine if younger and older listeners with normal hearing who differ on working memory span perform differently on speech recognition tests in noise. Older adults typically exhibit poorer speech recognition scores in noise than younger adults, which is attributed primarily to poorer hearing sensitivity and more limited working memory capacity in older than younger adults. Previous studies typically tested older listeners with poorer hearing sensitivity and shorter working memory spans than younger listeners, making it difficult to discern the importance of working memory capacity on speech recognition. This investigation controlled for hearing sensitivity and compared speech recognition performance in noise by younger and older listeners who were subdivided into high and low working memory groups. Performance patterns were compared for different speech materials to assess whether or not the effect of working memory capacity varies with the demands of the specific speech test. The authors hypothesized that (1) normal-hearing listeners with low working memory span would exhibit poorer speech recognition performance in noise than those with high working memory span; (2) older listeners with normal hearing would show poorer speech recognition scores than younger listeners with normal hearing, when the two age groups were matched for working memory span; and (3) an interaction between age and working memory would be observed for speech materials that provide contextual cues. Twenty-eight older (61 to 75 years) and 25 younger (18 to 25 years) normal-hearing listeners were assigned to groups based on age and working memory status. Northwestern University Auditory Test No. 6 words and Institute of Electrical and Electronics Engineers sentences were presented in noise using an adaptive procedure to measure the signal-to-noise ratio corresponding to 50% correct performance. Cognitive ability was evaluated with two tests of working memory (Listening Span Test and Reading Span Test) and two tests of processing speed (Paced Auditory Serial Addition Test and The Letter Digit Substitution Test). Significant effects of age and working memory capacity were observed on the speech recognition measures in noise, but these effects were mediated somewhat by the speech signal. Specifically, main effects of age and working memory were revealed for both words and sentences, but the interaction between the two was significant for sentences only. For these materials, effects of age were observed for listeners in the low working memory groups only. Although all cognitive measures were significantly correlated with speech recognition in noise, working memory span was the most important variable accounting for speech recognition performance. The results indicate that older adults with high working memory capacity are able to capitalize on contextual cues and perform as well as young listeners with high working memory capacity for sentence recognition. The data also suggest that listeners with normal hearing and low working memory capacity are less able to adapt to distortion of speech signals caused by background noise, which requires the allocation of more processing resources to earlier processing stages. These results indicate that both younger and older adults with low working memory capacity and normal hearing are at a disadvantage for recognizing speech in noise.

75 FR 71101 - Monroe Gas Storage Company, LLC; Notice of Application

Federal Register 2010, 2011, 2012, 2013, 2014

2010-11-22

... to comment only on the environmental review of this project should submit an original and two copies... Monroe to make changes to the certificated design of the Monroe Gas Storage Project. Specifically... high-deliverability working gas storage capacity, with about 4.46 Bcf of base gas. Nor is any change...

Incorporation of heterostructured Sn/SnO nanoparticles in crumpled nitrogen-doped graphene nanosheets for application as anodes in lithium-ion batteries.

PubMed

Du, Fei-Hu; Liu, Yu-Si; Long, Jie; Zhu, Qian-Cheng; Wang, Kai-Xue; Wei, Xiao; Chen, Jie-Sheng

2014-09-07

Sn/SnO nanoparticles are incorporated in crumpled nitrogen-doped graphene nanosheets by a simple melting diffusion method. The resulting composite exhibits large specific capacity, excellent cycling stability and high rate capability as an anode for lithium-ion batteries.

Improved performances of β-Ni(OH)2@reduced-graphene-oxide in Ni-MH and Li-ion batteries.

PubMed

Li, Baojun; Cao, Huaqiang; Shao, Jin; Zheng, He; Lu, Yuexiang; Yin, Jiefu; Qu, Meizhen

2011-03-21

Incorporation of reduced graphene oxide into β-Ni(OH)(2) presents high performances with specific discharge capacity of 283 mA hg(-1) after 50 cycles in Ni-MH batteries, and 507 mA hg(-1) after 30 cycles in Li ion batteries.

High-power and 2.5 kW advanced-technology ion thruster

NASA Technical Reports Server (NTRS)

Poeschel, R. L.

1977-01-01

Investigations for improving ion thruster components in the 30 cm engineering model thruster (EMT) resulted in the demonstration of useful techniques for grid short removal and discharge chamber erosion monitoring, establishment of relationships between double ion production and thruster operating parameters, verification of satisfactory specifications on porous tungsten vaporizer material and barium impregnated porous tungsten inserts, demonstration of a new hollow cathode configuration, and specification of magnetic circuit requirements for reproducing desired magnetic mappings. The capacity of a 30 cm EMT to operate at higher beam voltages and currents (higher power) was determined. Operation at 2 A beam current and higher beam voltage is shown to be essentially equivalent to operation at 1.1 kV with regard to efficiency, lifetime and operating conditions. The only additional requirement is an improvement in high voltage insulation and propellant isolator capacity. Operation at minimum voltage and higher beam currents is shown to increase thruster discharge chamber erosion in proportion to beam current. Studies to find alternatives to molybdenum for manufacturing ion optics grids are also reported.

In Situ Fabrication of Hierarchically Branched TiO2 Nanostructures: Enhanced Performance in Photocatalytic H2 Evolution and Li-Ion Batteries.

PubMed

Yang, Guorui; Wang, Ling; Peng, Shengjie; Wang, Jianan; Ji, Dongxiao; Yan, Wei; Ramakrishna, Seeram

2017-12-01

1D branched TiO 2 nanomaterials play a significant role in efficient photocatalysis and high-performance lithium ion batteries. In contrast to the typical methods which generally have to employ epitaxial growth, the direct in situ growth of hierarchically branched TiO 2 nanofibers by a combination of the electrospinning technique and the alkali-hydrothermal process is presented in this work. Such the branched nanofibers exhibit improvement in terms of photocatalytic hydrogen evolution (0.41 mmol g -1 h -1 ), in comparison to the conventional TiO 2 nanofibers (0.11 mmol g -1 h -1 ) and P25 (0.082 mmol g -1 h -1 ). Furthermore, these nanofibers also deliver higher lithium specific capacity at different current densities, and the specific capacity at the rate of 2 C is as high as 201. 0 mAh g -1 , roughly two times higher than that of the pristine TiO 2 nanofibers. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The Role of Climatic and Density Dependent Factors in Shaping Mosquito Population Dynamics: The Case of Culex pipiens in Northwestern Italy

PubMed Central

Giacobini, Mario; Pugliese, Andrea; Merler, Stefano; Rosà, Roberto

2016-01-01

Culex pipiens mosquito is a species widely spread across Europe and represents a competent vector for many arboviruses such as West Nile virus (WNV), which has been recently circulating in many European countries, causing hundreds of human cases. In order to identify the main determinants of the high heterogeneity in Cx. pipiens abundance observed in Piedmont region (Northwestern Italy) among different seasons, we developed a density-dependent stochastic model that takes explicitly into account the role played by temperature, which affects both developmental and mortality rates of different life stages. The model was calibrated with a Markov chain Monte Carlo approach exploring the likelihood of recorded capture data gathered in the study area from 2000 to 2011; in this way, we disentangled the role played by different seasonal eco-climatic factors in shaping the vector abundance. Illustrative simulations have been performed to forecast likely changes if temperature or density–dependent inputs would change. Our analysis suggests that inter-seasonal differences in the mosquito dynamics are largely driven by different temporal patterns of temperature and seasonal-specific larval carrying capacities. Specifically, high temperatures during early spring hasten the onset of the breeding season and increase population abundance in that period, while, high temperatures during the summer can decrease population size by increasing adult mortality. Higher densities of adult mosquitoes are associated with higher larval carrying capacities, which are positively correlated with spring precipitations. Finally, an increase in larval carrying capacity is expected to proportionally increase adult mosquito abundance. PMID:27105065

The staging mechanism of AlCl4 intercalation in a graphite electrode for an aluminium-ion battery.

PubMed

Bhauriyal, Preeti; Mahata, Arup; Pathak, Biswarup

2017-03-15

Identifying a suitable electrode material with desirable electrochemical properties remains a primary challenge for rechargeable Al-ion batteries. Recently an ultrafast rechargeable Al-ion battery was reported with high charge/discharge rate, (relatively) high discharge voltage and high capacity that uses a graphite-based cathode. Using calculations from first-principles, we have investigated the staging mechanism of AlCl 4 intercalation into bulk graphite and evaluated the stability, specific capacity and voltage profile of AlCl 4 intercalated compounds. Ab initio molecular dynamics is performed to investigate the thermal stability of AlCl 4 intercalated graphite structures. Our voltage profiles show that the first AlCl 4 intercalation step could be a more sluggish step than the successive intercalation steps. However, the diffusion of AlCl 4 is very fast in the expanded graphite host layers with a diffusion barrier of ∼0.01 eV, which justifies the ultrafast charging rate of a graphite based Al-ion battery. And such an AlCl 4 intercalated battery provides an average voltage of 2.01-2.3 V with a maximum specific capacity of 69.62 mA h g -1 , which is excellent for anion intercalated batteries. Our density of states and Bader charge analysis shows that the AlCl 4 intercalation into the bulk graphite is a charging process. Hence, we believe that our present study will be helpful in understanding the staging mechanism of AlCl 4 intercalation into graphite-like layered electrodes for Al-ion batteries, thus encouraging further experimental work.

Estimating aquifer transmissivity from specific capacity using MATLAB.

PubMed

McLin, Stephen G

2005-01-01

Historically, specific capacity information has been used to calculate aquifer transmissivity when pumping test data are unavailable. This paper presents a simple computer program written in the MATLAB programming language that estimates transmissivity from specific capacity data while correcting for aquifer partial penetration and well efficiency. The program graphically plots transmissivity as a function of these factors so that the user can visually estimate their relative importance in a particular application. The program is compatible with any computer operating system running MATLAB, including Windows, Macintosh OS, Linux, and Unix. Two simple examples illustrate program usage.

High-Density Three-Dimension Graphene Macroscopic Objects for High-Capacity Removal of Heavy Metal Ions

PubMed Central

Li, Weiwei; Gao, Song; Wu, Liqiong; Qiu, Shengqiang; Guo, Yufen; Geng, Xiumei; Chen, Mingliang; Liao, Shutian; Zhu, Chao; Gong, Youpin; Long, Mingsheng; Xu, Jianbao; Wei, Xiangfei; Sun, Mengtao; Liu, Liwei

2013-01-01

The chemical vapor deposition (CVD) fabrication of high-density three-dimension graphene macroscopic objects (3D-GMOs) with a relatively low porosity has not yet been realized, although they are desirable for applications in which high mechanical and electrical properties are required. Here, we explore a method to rapidly prepare the high-density 3D-GMOs using nickel chloride hexahydrate (NiCl2·6H2O) as a catalyst precursor by CVD process at atmospheric pressure. Further, the free-standing 3D-GMOs are employed as electrolytic electrodes to remove various heavy metal ions. The robust 3D structure, high conductivity (~12 S/cm) and large specific surface area (~560 m2/g) enable ultra-high electrical adsorption capacities (Cd2+ ~ 434 mg/g, Pb2+ ~ 882 mg/g, Ni2+ ~ 1,683 mg/g, Cu2+ ~ 3,820 mg/g) from aqueous solutions and fast desorption. The current work has significance in the studies of both the fabrication of high-density 3D-GMOs and the removal of heavy metal ions. PMID:23821107

Electrical, thermal and electrochemical properties of disordered carbon prepared from palygorskite and cane molasses

DOE Office of Scientific and Technical Information (OSTI.GOV)

Alvarez, Edelio Danguillecourt, E-mail: edelioalvarez42@gmail.com; Laffita, Yodalgis Mosqueda, E-mail: yodalgis@imre.uh.cu; Montoro, Luciano Andrey, E-mail: landrey.montoro@gmail.com

We have synthesized and electrochemically tested a carbon sample that was suitable as anode for lithium secondary battery. The synthesis was based on the use of the palygorskite clay as template and sugar cane molasses as carbon source. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, Brunauer–Emmett–Teller (BET) measurements and High Resolution Transmission Electron Microscope (HRTEM) analysis showed that the nanometric carbon material has a highly disordered graphene-like wrinkled structure and large specific surface area (467 m{sup 2} g{sup −1}). The compositional characterization revealed a 14% of heteroatoms-containing groups (O, H, N, S) doping the as-prepared carbon. Thermophysicalmore » measurements revealed the good thermal stability and an acceptable thermal diffusivity (9·10{sup −7} m{sup 2} s{sup −1}) and conductivity (1.1 W m{sup −1} K{sup −1}) of this carbon. The electrical properties showed an electronic conductivity of hole-like carriers of approximately one S/cm in a 173–293 K range. The testing of this material as anodes in a secondary lithium battery displayed a high specific capacity and excellent performance in terms of number of cycles. A high reversible capacity of 356 mA h g{sup −1} was reached. - Graphical abstract: TEM image and electrochemistry behavior of a new graphene oxide-like carbon. - Highlights: • A high disordered graphene oxide-like conducting carbon is reported. • The synthesis was based on palygorskite and sugar cane molasses as precursors. • The disordered conducting carbon is composed of doped- graphene heterogeneous domains. • This material combines a large specific surface area and high electric conductivity. • The thermophysical and electrochemical properties of this material reveal adequate behavior.« less

Amorphous MoS 3 Infiltrated with Carbon Nanotubes as an Advanced Anode Material of Sodium-Ion Batteries with Large Gravimetric, Areal, and Volumetric Capacities

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ye, Hualin; Wang, Lu; Deng, Shuo

The search for earth-abundant and high-performance electrode materials for sodium-ion batteries represents an important challenge to current battery research. 2D transition metal dichalcogenides, particularly MoS2, have attracted increasing attention recently, but few of them so far have been able to meet expectations. In this study, it is demonstrated that another phase of molybdenum sulfide—amorphous chain-like MoS3—can be a better choice as the anode material of sodium-ion batteries. Highly compact MoS3 particles infiltrated with carbon nanotubes are prepared via the facile acid precipitation method in ethylene glycol. Compared to crystalline MoS2, the resultant amorphous MoS3 not only exhibits impressive gravimetric performance—featuringmore » excellent specific capacity (≈615 mA h g-1), rate capability (235 mA h g-1 at 20 A g-1), and cycling stability but also shows exceptional volumetric capacity of ≈1000 mA h cm-3 and an areal capacity of >6.0 mA h cm-2 at very high areal loadings of active materials (up to 12 mg cm-2). The experimental results are supported by density functional theory simulations showing that the 1D chains of MoS3 can facilitate the adsorption and diffusion of Na+ ions. At last, it is demonstrated that the MoS3 anode can be paired with an Na3V2(PO4)3 cathode to afford full cells with great capacity and cycling performance.« less

[Assessment of Functioning when Conducting Occupational Capacity Evaluations--What is "Evidence-Based"?].

PubMed

Canela, Carlos; Schleifer, Roman; Dube, Anish; Hengartner, Michael P; Ebner, Gerhard; Seifritz, Erich; Liebrenz, Michael

2016-03-01

Occupational capacity evaluations have previously been subject to criticism for lacking in quality and consistency. To the authors' knowledge, there is no clear consensus on the best way to formally assess functioning within capacity evaluations. In this review we investigated different instruments that are used to assess functioning in occupational capacity evaluations. Systematic review of the literature. Though several instruments that assess functional capacity were found in our search, a specific validated instrument assessing occupational capacity as part of a larger psychiatric evaluation was not found. The limitations of the existing instruments on assessing functional capacity are discussed. Medical experts relying on instruments to conduct functional capacity evaluations should be cognizant of their limitations. The findings call for the development and use of an instrument specifically designed to assess the functional and occupational capacity of psychiatric patients, which is also likely to improve the quality of these reports. © Georg Thieme Verlag KG Stuttgart · New York.

FeP@C Nanotube Arrays Grown on Carbon Fabric as a Low Potential and Freestanding Anode for High-Performance Li-Ion Batteries.

PubMed

Xu, Xijun; Liu, Jun; Liu, Zhengbo; Wang, Zhuosen; Hu, Renzong; Liu, Jiangwen; Ouyang, Liuzhang; Zhu, Min

2018-06-26

An anode of self-supported FeP@C nanotube arrays on carbon fabric (CF) is successfully fabricated via a facile template-based deposition and phosphorization route: first, well-aligned FeOOH nanotube arrays are simply obtained via a solution deposition and in situ etching route with hydrothermally crystallized (Co,Ni)(CO 3 ) 0.5 OH nanowire arrays as the template; subsequently, these uniform FeOOH nanotube arrays are transformed into robust carbon-coated Fe 3 O 4 (Fe 3 O 4 @C) nanotube arrays via glucose adsorption and annealing treatments; and finally FeP@C nanotube arrays on CF are achieved through the facile phosphorization of the oxide-based arrays. As an anode for lithium-ion batteries (LIBs), these FeP@C nanotube arrays exhibit superior rate capability (reversible capacities of 945, 871, 815, 762, 717, and 657 mA h g -1 at 0.1, 0.2, 0.4, 0.8, 1.3, and 2.2 A g -1 , respectively, corresponding to area specific capacities of 1.73, 1.59, 1.49, 1.39, 1.31, 1.20 mA h cm -2 at 0.18, 0.37, 0.732, 1.46, 2.38, and 4.03 mA cm -2 , respectively) and a stable long-cycling performance (a high specific capacity of 718 mA h g -1 after 670 cycles at 0.5 A g -1 , corresponding to an area capacity of 1.31 mA h cm -2 at 0.92 mA cm -2 ). © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Multifaceted role of clay minerals in pharmaceuticals

PubMed Central

Khurana, Inderpreet Singh; Kaur, Satvinder; Kaur, Harpreet; Khurana, Rajneet Kaur

2015-01-01

The desirable physical and physiochemical properties of clay minerals have led them to play a substantial role in pharmaceutical formulations. Clay minerals like kaolin, smectite and palygorskite-sepiolite are among the world's most valuable industrial minerals and of considerable importance. The elemental features of clay minerals which caused them to be used in pharmaceutical formulations are high specific area, sorption capacity, favorable rheological properties, chemical inertness, swelling capacity, reactivity to acids and inconsiderable toxicity. Of course, these are highly cost effectual. This special report on clay minerals provides a bird's eye view of the chemical composition and structure of these minerals and their influence on the release properties of active medicinal agents. Endeavor has been made to rope in myriad applications depicting the wide acceptability of these clay minerals. PMID:28031881

Thermally-responsive, nonflammable phosphonium ionic liquid electrolytes for lithium metal batteries: operating at 100 degrees celsius.

PubMed

Lin, X; Kavian, R; Lu, Y; Hu, Q; Shao-Horn, Y; Grinstaff, M W

2015-11-13

Rechargeable batteries such as Li ion/Li metal batteries are widely used in the electronics market but the chemical instability of the electrolyte limits their use in more demanding environmental conditions such as in automotive, oil exploration, or mining applications. In this study, a series of alkyl phosphonium ionic liquid electrolyte are described with high thermal stability and solubility for LiTFSI. A lithium metal battery (LMB) containing a tailored phosphonium ionic liquid/LiTFSI electrolyte operates at 100 °C with good specific capacities and cycling stability. Substantial capacity is maintained during 70 cycles or 30 days. Instant on-off battery operation is realized via the significant temperature dependence of the electrolyte material, demonstrating the robustness and potential for use at high temperature.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Jeong, Sookyung; Li, Xiaolin; Zheng, Jianming

With the ever increasing demands on Li-ion batteries with higher energy densities, alternative anode with higher reversible capacity is required to replace the conventional graphite anode. Here, we demonstrate a cost-effective hydrothermal-carbonization approach to prepare the hard carbon coated nano-Si/graphite (HC-nSi/G) composite as a high performance anode for Li-ion batteries. In this hierarchical structured composite, the hard carbon coating layer not only provides an efficient pathway for electron transfer, but also alleviates the volume variation of silicon during charge/discharge processes. The HC-nSi/G composite electrode shows excellent electrochemical performances including a high specific capacity of 878.6 mAh g-1 based on themore » total weight of composite, good rate performance and a decent cycling stability, which is promising for practical applications.« less

Hybrid aerogel-derived Sn-Ni alloy immobilized within porous carbon/graphene dual matrices for high-performance lithium storage.

PubMed

Zhang, Hao; Zhang, Mengru; Zhang, Meiling; Zhang, Lin; Zhang, Anping; Zhou, Yiming; Wu, Ping; Tang, Yawen

2017-09-01

Nanoporous networks of tin-based alloys immobilized within carbon matrices possess unique structural and compositional superiorities toward lithium-storage, and are expected to manifest improved strain-accommodation and charge-transport capabilities and thus desirable anodic performance for advanced lithium-ion batteries (LIBs). Herein, a facile and scalable hybrid aerogel-derived thermal-autoreduction route has been developed for the construction of nanoporous network of SnNi alloy immobilized within carbon/graphene dual matrices (SnNi@C/G network). When applied as an anode material for LIBs, the SnNi@C/G network manifests desirable lithium-storage performances in terms of specific capacities, cycle life, and rate capability. The facile aerogel-derived route and desirable Li-storage performance of the SnNi@C/G network facilitate its practical application as a high-capacity, long-life, and high-rate anode material for advanced LIBs. Copyright © 2017 Elsevier Inc. All rights reserved.

Porous and magnetic molecularly imprinted polymers via Pickering high internal phase emulsions polymerization for selective adsorption of λ-cyhalothrin

NASA Astrophysics Data System (ADS)

Wu, Yunlong; Ma, Yue; Pan, Jianming; Gu, Runxing; Luo, Jialu

2017-03-01

A novel macroporous magnetic molecularly imprinted polymer (MMIPs) of was prepared by W/O Pickering (high internal phase emulsions) HIPEs polymerization, and then it was adopted as adsorbent for selective adsorption of λ-cyhalothrin (LC). In static conditions, adsorption capacity of LC increased rapidly in the first 60 min and reached to equilibrium in approximately 2.0 h. Excellent conformity of the second-order model confirmed the chemical nature of the interaction between the LC and imprinted sites. The fitting adsorption isotherm was a Langmuir type, and the maximum monolayer adsorption capacity at 298 K was 404.4 µmol g-1. Thermodynamic parameters suggested the specific adsorption at 298 K was an exothermic, spontaneous, and entropy decreased process. Competitive recognition studies of the MMIPs were performed with diethyl phthalate (DEP) and the structurally similar compound fenvalerate (FL), and the MMIPs, which displayed high selectivity for LC.

High performance porous Si@C anodes synthesized by low temperature aluminothermic reaction

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mishra, Kuber; Zheng, Jianming; Patel, Rajankumar

A low temperature (210°C) aluminothermic reduction reaction process has been developed to synthesis porous silicon (Si) as an anode for Li ion battery applications. An eutectic mixture of AlCl3 and ZnCl2 is used as the mediator to reduce the reaction temperature. With carbon pre-coated on the porous SiO2 precursor, porous Si@C core shell structured anodes could be obtained with structure and morphology similar to that of the porous precursor. In addition, carbon coated porous Si also exhibits superior cyclic stability, higher rate performance, and higher coulombic efficiency. The porous Si anode demonstrates a high specific capacity of ~2100 mAh/g atmore » the current density of 1.2 A/g and has a good cycling stability with ~76% capacity retention over 250 cycles. Therefore, it will be a good candidate for anode used in high energy density Li-ion batteries.« less

Porous and Magnetic Molecularly Imprinted Polymers via Pickering High Internal Phase Emulsions Polymerization for Selective Adsorption of λ-Cyhalothrin.

PubMed

Wu, Yunlong; Ma, Yue; Pan, Jianming; Gu, Runxing; Luo, Jialu

2017-01-01

A novel macroporous magnetic molecularly imprinted polymer (MMIPs) of was prepared by W/O Pickering (high internal phase emulsions) HIPEs polymerization, and then it was adopted as adsorbent for selective adsorption of λ-cyhalothrin (LC). In static conditions, adsorption capacity of LC increased rapidly in the first 60 min and reached to equilibrium in ~2.0 h. Excellent conformity of the second-order model confirmed the chemical nature of the interaction between the LC and imprinted sites. The fitting adsorption isotherm was a Langmuir type, and the maximum monolayer adsorption capacity at 298 K was 404.4 μmol g -1 . Thermodynamic parameters suggested the specific adsorption at 298 K was an exothermic, spontaneous, and entropy decreased process. Competitive recognition studies of the MMIPs were performed with diethyl phthalate (DEP) and the structurally similar compound fenvalerate (FL), and the MMIPs, which displayed high selectivity for LC.

Porous and Magnetic Molecularly Imprinted Polymers via Pickering High Internal Phase Emulsions Polymerization for Selective Adsorption of λ-Cyhalothrin

PubMed Central

Wu, Yunlong; Ma, Yue; Pan, Jianming; Gu, Runxing; Luo, Jialu

2017-01-01

A novel macroporous magnetic molecularly imprinted polymer (MMIPs) of was prepared by W/O Pickering (high internal phase emulsions) HIPEs polymerization, and then it was adopted as adsorbent for selective adsorption of λ-cyhalothrin (LC). In static conditions, adsorption capacity of LC increased rapidly in the first 60 min and reached to equilibrium in ~2.0 h. Excellent conformity of the second-order model confirmed the chemical nature of the interaction between the LC and imprinted sites. The fitting adsorption isotherm was a Langmuir type, and the maximum monolayer adsorption capacity at 298 K was 404.4 μmol g−1. Thermodynamic parameters suggested the specific adsorption at 298 K was an exothermic, spontaneous, and entropy decreased process. Competitive recognition studies of the MMIPs were performed with diethyl phthalate (DEP) and the structurally similar compound fenvalerate (FL), and the MMIPs, which displayed high selectivity for LC. PMID:28401145

Assessment of metal retention in newly constructed highway embankments.

PubMed

Werkenthin, Moritz; Kluge, Björn; Wessolek, Gerd

2016-12-01

Newly constructed embankments should provide both a specific bearing capacity to enable trafficability in emergency cases and a sufficient pollutant retention capacity to protect the groundwater. A number of lysimeters were installed along the A115 highway to determine total and dissolved metal concentrations in road runoff and in the soil solution of newly constructed embankments. Dissolved concentrations in soil solution of the embankments did not exceed the trigger values of the German legislation. Depending on the metal, total concentrations in soil solution were more than twice as high as dissolved concentrations. The high infiltration rates lead to increased groundwater recharge beneath the embankments (up to 4100 mm a -1 ). Although metal concentrations were not problematic from the legislators' point of view, the elevated infiltration rates beside the road facilitated the transfer of high metal loads into deeper soil layers and potentially into the groundwater as well.

An ultra-tunable platform for molecular engineering of high-performance crystalline porous materials

DOE PAGES

Zhai, Quan -Guo; Bu, Xianhui; Mao, Chengyu; ...

2016-12-07

Metal-organic frameworks are a class of crystalline porous materials with potential applications in catalysis, gas separation and storage, and so on. Of great importance is the development of innovative synthetic strategies to optimize porosity, composition and functionality to target specific applications. Here we show a platform for the development of metal-organic materials and control of their gas sorption properties. This platform can accommodate a large variety of organic ligands and homo- or hetero-metallic clusters, which allows for extraordinary tunability in gas sorption properties. Even without any strong binding sites, most members of this platform exhibit high gas uptake capacity. Asmore » a result, the high capacity is accomplished with an isosteric heat of adsorption as low as 20 kJ mol –1 for carbon dioxide, which could bring a distinct economic advantage because of the significantly reduced energy consumption for activation and regeneration of adsorbents.« less

Na4Mn9O18/Carbon Nanotube Composite as a High Electrochemical Performance Material for Aqueous Sodium-Ion Batteries.

PubMed

Yin, Fuxing; Liu, Zhengjun; Yang, Shuang; Shan, Zhenzhen; Zhao, Yan; Feng, Yuting; Zhang, Chengwei; Bakenov, Zhumabay

2017-10-17

The aqueous sodium-ion battery (ASIB) is one of the promising new energy storage systems owing to the abundant resources of sodium as well as efficiency and safety of electrolyte. Herein, we report an ASIB system with Na 4 Mn 9 O 18 /carbon nanotube (NMO/CNT) as cathode, metal Zn as anode and a novel Na + /Zn 2+ mixed ion as electrolyte. The NMO/CNT with microspherical structure is prepared by a simple spray-drying method. The prepared battery delivers a high reversible specific capacity and stable cyclability. Furthermore, the battery displays a stable reversible discharge capacity of 53.2 mAh g -1 even at a high current rate of 4 C after 150 cycles. Our results confirm that the NMO/CNT composite is a promising electrode cathode material for ASIBs.

Toward Aerogel Electrodes of Superior Rate Performance in Supercapacitors through Engineered Hollow Nanoparticles of NiCo2O4

PubMed Central

Li, Jianjiang; Chen, Shuai; Zhu, Xiaoyi; She, Xilin; Liu, Tongchao; Zhang, Huawei; Komarneni, Sridhar

2017-01-01

Abstract A biomass‐templated pathway is developed for scalable synthesis of NiCo2O4@carbon aerogel electrodes for supercapacitors, where NiCo2O4 hollow nanoparticles with an average outer diameter of 30–40 nm are conjoined by graphitic carbon forming a 3D aerogel structure. This kind of NiCo2O4 aerogel structure shows large specific surface area (167.8 m2 g−1), high specific capacitance (903.2 F g−1 at a current density of 1 A g−1), outstanding rate performance (96.2% capacity retention from 1 to 10 A g−1), and excellent cycling stability (nearly without capacitance loss after 3000 cycles at 10 A g−1). The unique structure of the 3D hollow aerogel synergistically contributes to the high performance. For instance, the 3D interconnected porous structure of the aerogel is beneficial for electrolyte ion diffusion and for shortening the electron transport pathways, and thus can improve the rate performance. The conductive carbon joint greatly enhances the specific capacity, and the hollow structure prohibits the volume changes during the charge–discharge process to significantly improve the cycling stability. This work represents a giant step toward the preparation of high‐performance commercial supercapacitors. PMID:29270344

A Shell-Shaped Carbon Architecture with High-Loading Capability for Lithium Sulfide Cathodes

DOE Office of Scientific and Technical Information (OSTI.GOV)

Chung, Sheng-Heng; Han, Pauline; Chang, Chi-Hao

We present that lithium sulfide (Li 2S) is considered a highly attractive cathode for establishing high-energy-density rechargeable batteries, especially due to its high charge-storage capacity and compatibility with lithium-metal-free anodes. Although various approaches have recently been pursued with Li 2S to obtain high performance, formidable challenges still remain with cell design (e.g., low Li 2S loading, insufficient Li 2S content, and an excess electrolyte) to realize high areal, gravimetric, and volumetric capacities. This study demonstrates a shell-shaped carbon architecture for holding pure Li 2S, offering innovation in cell-design parameters and gains in electrochemical characteristics. The Li 2S core–carbon shell electrodemore » encapsulates the redox products within the conductive shell so as to facilitate facile accessibility to electrons and ions. The fast redox-reaction kinetics enables the cells to attain the highest Li 2S loading of 8 mg cm -2 and the lowest electrolyte/Li 2S ratio of 9/1, which is the best cell-design specifications ever reported with Li 2S cathodes so far. Lastly, benefiting from the excellent cell-design criterion, the core–shell cathodes exhibit stable cyclability from slow to fast cycle rates and, for the first time, simultaneously achieve superior performance metrics with areal, gravimetric, and volumetric capacities.« less

New Approach to Create TiO2(B)/Carbon Core/Shell Nanotubes: Ideal Structure for Enhanced Lithium Ion Storage.

PubMed

Zhu, Xiaoyi; Yang, Xianfeng; Lv, Chunxiao; Guo, Shaojun; Li, Jianjiang; Zheng, Zhanfeng; Zhu, Huaiyong; Yang, Dongjiang

2016-07-27

To achieve uniform carbon coating on TiO2 nanomaterials, high temperature (>500 °C) annealing treatment is a necessity. However, the annealing treatment inevitably leads to the strong phase transformation from TiO2(B) with high lithium ion storage (LIS) capacity to anatase with low LIS one as well as the damage of nanostructures. Herein, we demonstrate a new approach to create TiO2(B)/carbon core/shell nanotubes (C@TBNTs) using a long-chain silane polymethylhydrosiloxane (PMHS) to bind the TBNTs by forming Si-O-Ti bonds. The key feature of this work is that the introduction of PMHS onto TBNTs can afford TBNTs with very high thermal stability at higher than 700 °C and inhibit the phase transformation from TiO2(B) to anatase. Such a high thermal property of PMHS-TBNTs makes them easily coated with highly graphitic carbon shell via CVD process at 700 °C. The as-prepared C@TBNTs deliver outstanding rate capability and electrochemical stability, i.e., reversible capacity above 250 mAh g(-1) at 10 C and a high specific capacity of 479.2 mAh g(-1) after 1000 cycles at 1 C. As far as we know, the LIS performance of our sample is the highest among the previously reported TiO2(B) anode materials.

A Shell-Shaped Carbon Architecture with High-Loading Capability for Lithium Sulfide Cathodes

DOE PAGES

Chung, Sheng-Heng; Han, Pauline; Chang, Chi-Hao; ...

2017-05-11

We present that lithium sulfide (Li 2S) is considered a highly attractive cathode for establishing high-energy-density rechargeable batteries, especially due to its high charge-storage capacity and compatibility with lithium-metal-free anodes. Although various approaches have recently been pursued with Li 2S to obtain high performance, formidable challenges still remain with cell design (e.g., low Li 2S loading, insufficient Li 2S content, and an excess electrolyte) to realize high areal, gravimetric, and volumetric capacities. This study demonstrates a shell-shaped carbon architecture for holding pure Li 2S, offering innovation in cell-design parameters and gains in electrochemical characteristics. The Li 2S core–carbon shell electrodemore » encapsulates the redox products within the conductive shell so as to facilitate facile accessibility to electrons and ions. The fast redox-reaction kinetics enables the cells to attain the highest Li 2S loading of 8 mg cm -2 and the lowest electrolyte/Li 2S ratio of 9/1, which is the best cell-design specifications ever reported with Li 2S cathodes so far. Lastly, benefiting from the excellent cell-design criterion, the core–shell cathodes exhibit stable cyclability from slow to fast cycle rates and, for the first time, simultaneously achieve superior performance metrics with areal, gravimetric, and volumetric capacities.« less

Geography literation to improve spatial intelligence of high school student

NASA Astrophysics Data System (ADS)

Utami, WS; Zain, IM

2018-01-01

Spatial intelligence is deeply related to success in the STEM disciplines (science,technology, engineering, and math). spatial intelligence as a transversal capacity which is useful for everyday life but which cannot be characterized in any specific and distinctive way, as are, for example, linguistic or mathematical ability. The ability of geographical literacy relates to spatial intelligence. test results prove that the ability of high-liter geography of high school students found in students who have a good spatial intelligence score

Copper-Exchanged Zeolite L Traps Oxygen

NASA Technical Reports Server (NTRS)

Sharma, Pramod K.; Seshan, Panchalam K.

1991-01-01

Brief series of simple chemical treatments found to enhance ability of zeolite to remove oxygen from mixture of gases. Thermally stable up to 700 degrees C and has high specific surface area which provides high capacity for adsorption of gases. To increase ability to adsorb oxygen selectively, copper added by ion exchange, and copper-exchanged zeolite reduced with hydrogen. As result, copper dispersed atomically on inner surfaces of zeolite, making it highly reactive to oxygen, even at room temperature. Reactivity to oxygen even greater at higher temperatures.

A Sustainable Route from Biomass Byproduct Okara to High Content Nitrogen-Doped Carbon Sheets for Efficient Sodium Ion Batteries.

PubMed

Yang, Tingzhou; Qian, Tao; Wang, Mengfan; Shen, Xiaowei; Xu, Na; Sun, Zhouzhou; Yan, Chenglin

2016-01-20

A sustainable route from the biomass byproduct okara as a natural nitrogen fertilizer to high-content N-doped carbon sheets is demonstrated. The as-prepared unique structure exhibits high specific capacity (292 mAh g(-1) ) and extremely long cycle life (exceeding 2000 cycles). A full battery is devised for the practical use of materials with a flexible/wearable LED screen. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Advanced Li-Ion Hybrid Supercapacitors Based on 3D Graphene-Foam Composites.

PubMed

Liu, Wenwen; Li, Jingde; Feng, Kun; Sy, Abel; Liu, Yangshuai; Lim, Lucas; Lui, Gregory; Tjandra, Ricky; Rasenthiram, Lathankan; Chiu, Gordon; Yu, Aiping

2016-10-05

Li-ion hybrid supercapacitors (LIHSs) have recently attracted increasing attention as a new and promising energy storage device. However, it is still a great challenge to construct novel LIHSs with high-performance due to the majority of battery-type anodes retaining the sluggish kinetics of Li-ion storage and most capacitor-type cathodes with low specific capacitance. To solve this problem, 3D graphene-wrapped MoO 3 nanobelt foam with the unique porous network structure has been designed and prepared as anode material, which delivers high capacity, improved rate performance, and enhanced cycle stability. First-principles calculation reveals that the combination of graphene dramatically reduces the diffusion energy barrier of Li + adsorbed on the surface of MoO 3 nanobelt, thus improving its electrochemical performance. Furthermore, 3D graphene-wrapped polyaniline nanotube foam derived carbon is employed as a new type of capacitor-type cathode, demonstrating high specific capacitance, good rate performance, and long cycle stability. Benefiting from these two graphene foam-enhanced materials, the constructed LIHSs show a wide operating voltage range (3.8 V), a long stable cycle life (90% capacity retention after 3000 cycles), a high energy density (128.3 Wh·kg -1 ), and a high power density (13.5 kW·kg -1 ). These encouraging performances indicate that the obtained LIHSs may have promising prospect as next-generation energy-storage devices.

Alumina-coated and manganese monoxide embedded 3D carbon derived from avocado as high-performance anode for lithium-ion batteries

NASA Astrophysics Data System (ADS)

rehman, Wasif ur; Xu, Youlong; Du, Xianfeng; Sun, Xiaofei; Ullah, Inam; Zhang, Yuan; Jin, Yanling; Zhang, Baofeng; Li, Xifei

2018-07-01

Derived from avocado fruit, a three dimension (3D) carbon is prepared via a hydrothermal/pyrolysis process followed by embedding with MnO nanoparticles by a wet chemical method and coating with Al2O3 through an atomic layer deposition technique. The obtained material presents a hierarchical structure that MnO nanocrystals wrapped in 3D carbon and then encapsulated in a uniform Al2O3 layer with a thickness of about 5 nm. Benefiting from this hierarchical structure in which 3D carbon offers numerous electronic pathways to enhance the conductivity and Al2O3 nanolayer provide a shelter to keep away from dissolution of Mn4+ and volume changes during charge/discharge process. This material (marked as C/MnO@Al2O3) has exhibited high rate performance and excellent cyclability as an anode for lithium ion batteries. A high specific capacity of about 600 mA h g-1 is achieved at a current density of 1000 mA g-1 and the electrode can still deliver a high specific capacity of about 1165 mA h g-1 at 150 mA g-1 after 100 cycles. These results facilitate a green and high potential of anode materials towards promising devices for advance performance of lithium-ion batteries.

Food Composition Tables in Southeast Asia: The Contribution of the SMILING Project.

PubMed

Hulshof, Paul; Doets, Esmee; Seyha, Sok; Bunthang, Touch; Vonglokham, Manithong; Kounnavong, Sengchanh; Famida, Umi; Muslimatun, Siti; Santika, Otte; Prihatini, Sri; Nazarudin, Nazarina; Jahari, Abas; Rojroongwasinkul, Nipa; Chittchang, Uraiporn; Mai, Le Bach; Dung, Le Hong; Lua, Tran Thi; Nowak, Verena; Elburg, Lucy; Melse-Boonstra, Alida; Brouwer, Inge

2018-06-08

Objectives Food composition data are key for many nutrition related activities in research, planning and policy. Combatting micronutrient malnutrition among women and young children using sustainable food based approaches, as aimed at in the SMILING project, requires high quality food composition data. Methods In order to develop capacity and to align procedures for establishing, updating and assessing the quality of key nutrient data in the food composition tables in Southeast Asia, a detailed roadmap was developed to identify and propose steps for this. This included a training workshop to build capacity in the field of food composition data, and alignment of procedures for selecting foods and nutrients to be included for quality assessment, and update of country specific food composition tables. The SEA partners in the SMILING project finalised a country specific food composition table (FCT) with updated compositional data on selected foods and nutrients considered key for designing nutrient dense and optimal diets for the target groups. Results Between 140 and 175 foods were selected for inclusion in the country specific FCTs. Key-nutrients were: energy, protein, total fat, carbohydrates, iron, zinc, (pro-)-vitamin A, folate, calcium, vitamin D, vitamin B1, vitamin B2, vitamin B3, vitamin B6, vitamin B12 and vitamin C. A detailed quality assessment on 13 key-foods per nutrient was performed using international guidelines. Nutrient data for specific local food items were often unavailable and data on folate, vitamin B12 and vitamin B6 contents were mostly missing. For many foods, documentation was not available, thereby complicating an in-depth quality assessment. Despite these limitations, the SMILING project offered a unique opportunity to increase awareness of the importance of high quality well documented food composition data. Conclusion for Practise The self-reported data quality demonstrated that there is considerable room for improvement of the nutrient data quality in some countries. In addition, investment in sustainable capacity development and an urgent need to produce and document high quality data on the micronutrient composition of especially local foods is required.

Enhancing Adsorption Capacity while Maintaining Specific Recognition Performance of Mesoporous Silica: A Novel Imprinting Strategy with Amphiphilic Ionic Liquid as Surfactant.

PubMed

Ding, Shichao; Li, Zhiling; Cheng, Yuan; Du, Chunbao; Gao, Junfeng; Zhang, Yong-Wei; Zhang, Nan; Li, Zhaotong; Chang, Ninghui; Hu, Xiaoling

2018-06-21

In order to facilitate the broad applications of molecular recognition materials in biomedical areas, it is critical to enhance their adsorption capacity while maintaining their excellent recognition performance. In this work, we designed and synthesized well-defined peptide-imprinted mesoporous silica (PIMS) for specific recognition of an immunostimulating hexapeptide from human casein (IHHC) by using amphiphilic ionic liquid as the surfactant to anchor IHHC via a combination of one step sol-gel method and docking oriented imprinting approach. Thereinto, theoretical calculation was employed to reveal the multiple binding interactions and dual-template configuration between amphiphilic ionic liquid and IHHC. The fabricated PIMS was characterized and an in-depth analysis of specific recognition mechanism was conducted. Results revealed that both adsorption and recognition capabilities of PIMS far exceeded that of the NIMS's. More significantly, the PIMS exhibited a superior binding capacity (60.5 mg g-1), which could increase 18.9% than the previous work. The corresponding imprinting factor and selectivity coefficient could reach up to 4.51 and 3.30, respectively. The PIMS also possessed lickety-split kinetic binding for IHHC, which the equilibrium time was only 10 min. All of these merits were due to the high surface area and the synergistic effect of multiple interactions (including hydrogen bonding, π-π stacking, ion-ion electrostatic interactions and van der Waals interactions, etc.) between PIMS and IHHC in imprinted sites. The present work suggests the potential application of PIMS for large-scale and high-effective separation of IHHC, which may lead to their broad applications in drug/gene deliver, biosensors, catalyst and so on. © 2018 IOP Publishing Ltd.

Antigen vehiculization particles based on the Z protein of Junin virus.

PubMed

Borio, Cristina S; Bilen, Marcos F; Argüelles, Marcelo H; Goñi, Sandra E; Iserte, Javier A; Glikmann, Graciela; Lozano, Mario E

2012-11-02

Arenavirus matrix protein Z plays an important role in virus budding and is able to generate enveloped virus-like-particles (VLPs) in absence of any other viral proteins. In these VLPs, Z protein is associated to the plasma membrane inner surface by its myristoyl residue. Budding induction and vesicle formation properties can be exploited to generate enveloped VLPs platform. These structures can be designed to carry specific antigen in the inner side or on the surface of VLPs.Vaccines based on VLPs are a highly effective type of subunit vaccines that mimic the overall structure of virus particles in absence of viral nucleic acid, being noninfectious.In this work we assayed the capacity of Junin Z protein to produce VLPs carrying the green fluorescent protein (eGFP), as a model antigen. In this report the Junin Z protein ability to produce VLPs from 293T cells and its capacity to deliver a specific antigen (eGFP) fused to Z was evaluated. Confocal microscopy showed a particular membrane bending in cells expressing Z and a spot welded distribution in the cytoplasm. VLPs were detected by TEM (transmission electron microscopy) and were purified from cell supernatant. The proteinase protection assay demonstrated the VLPs integrity and the absence of degradation of the fused antigen, thus indicating its internal localization. Finally, immunization of mice with purified VLPs produced high titres of anti-eGFP antibodies compared to the controls. It was proved that VLPs can be generated from cells transfected with a fusion Junin virus Z-eGFP protein in absence of any other viral protein, and the capacity of Z protein to support fusions at the C-terminal, without impairing its budding activity, allowing vehiculization of specific antigens into VLPs.

Needs, Effectiveness, and Gap Assessment for Key A-10C Missions: An Overview of Findings

DTIC Science & Technology

2016-01-01

weapons, further decreasing capacity. The GPS-guided SDB I ( GBU - 39 ) and the multimode SDB II ( GBU -53) begin to be highly useful in these circumstances...fairly close to friendly forces.8 It is specifically designed for use against moving targets; a Link 16 datalink permits target updates in flight, if...not jammed, and a laser-guidance mode allows it to be guided to specific targets if a JTAC is available to provide laser designation . It also has

Facile Stabilization of the Sodium Metal Anode with Additives: Unexpected Key Role of Sodium Polysulfide and Adverse Effect of Sodium Nitrate.

PubMed

Wang, Huan; Wang, Chuanlong; Matios, Edward; Li, Weiyang

2018-06-25

Sodium metal is an attractive anode for next-generation energy storage systems owing to its high specific capacity, low cost, and high abundance. Nevertheless, uncontrolled Na dendrite growth caused by the formation of unstable solid electrolyte interphase (SEI) leads to poor cycling performance and severe safety concerns. Sodium polysulfide (Na 2 S 6 ) alone is revealed to serve as a positive additive or pre-passivation agent in ether electrolyte to improve the long-term stability and reversibility of the Na anode, while Na 2 S 6 -NaNO 3 as co-additive has an adverse effect, contrary to the prior findings in the lithium anode system. A superior cycling behavior of Na anode is first demonstrated at a current density up to 10 mA cm -2 and a capacity up to 5 mAh cm -2 over 100 cycles. As a proof of concept, a high-capacity Na-S battery was prepared by pre-passivating the Na anode with Na 2 S 6 . This study gives insights into understanding the differences between Li and Na systems. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cobalt oxide-carbon nanosheet nanoarchitecture as an anode for high-performance lithium-ion battery.

PubMed

Wang, Huanlei; Mao, Nan; Shi, Jing; Wang, Qigang; Yu, Wenhua; Wang, Xin

2015-02-04

To improve the electrochemical performance of cobalt oxide owing to its inherent poor electrical conductivity and large volume expansion/contraction, Co3O4-carbon nanosheet hybrid nanoarchitectures were synthesized by a facile and scalable chemical process. However, it is still a challenge to control the size of Co3O4 particles down to ∼5 nm. Herein, we created nanosized cobalt oxide anchored 3D arrays of carbon nanosheets by the control of calcination condition. The uniformly dispersed Co3O4 nanocrystals on carbon nanosheets held a diameter down to ∼5 nm. When tested as anode materials for lithium-ion batteries, high lithium storage over 1200 mAh g(-1) is achieved, whereas high rate capability with capacity of about 390 mAh g(-1) at 10 A g(-1) is maintained through nanoscale diffusion distances and interconnected porous structure. After 500 cycles, the cobalt oxide-carbon nansheets hybrid display a reversible capacity of about 970 mAh g(-1) at 1 A g(-1). The synergistic effect between nanosized cobalt oxide and sheetlike interconnected carbon nanosheets lead to the greatly improved specific capacity and the initial Coulombic efficiency of the hybrids.

[Loss of appetite in elderly people in the community and its relationship with functional capacity].

PubMed

Serra Prat, Mateu; Fernández, Xavier; Ribó, Laura; Palomera, Elisabet; Papiol, Mònica; Serra, Pere

2008-04-19

The reasons of anorexia of ageing are multiple and not well-known. One of them is loss of appetite. We aimed to know the prevalence of self-reported appetite-loss in the elderly and its relationship with nutritional status, muscle strength and functional capacity. A population based cross-sectional study in which 236 non-institutionalized subjects over 70 years were randomly selected. Hand grip, functional capacity and nutritional status were assessed and a specific questionnaire was administered to assess appetite. Anorexia or loss of appetite was considered when subjects declared none or low usual appetite both in breakfast and lunch time. A 30.0% global prevalence of anorexia was observed (37.1% in females and 17.9% in males; p = 0.001). Loss of appetite was related to higher risk of malnutrition (41% in anorexic vs 27% in non-anorexic; p = 0.039), lower muscular strength and poorer functional capacity. Loss of appetite in the elderly has a high prevalence and must alert about frailty.

Working memory capacity and visual-verbal cognitive load modulate auditory-sensory gating in the brainstem: toward a unified view of attention.

PubMed

Sörqvist, Patrik; Stenfelt, Stefan; Rönnberg, Jerker

2012-11-01

Two fundamental research questions have driven attention research in the past: One concerns whether selection of relevant information among competing, irrelevant, information takes place at an early or at a late processing stage; the other concerns whether the capacity of attention is limited by a central, domain-general pool of resources or by independent, modality-specific pools. In this article, we contribute to these debates by showing that the auditory-evoked brainstem response (an early stage of auditory processing) to task-irrelevant sound decreases as a function of central working memory load (manipulated with a visual-verbal version of the n-back task). Furthermore, individual differences in central/domain-general working memory capacity modulated the magnitude of the auditory-evoked brainstem response, but only in the high working memory load condition. The results support a unified view of attention whereby the capacity of a late/central mechanism (working memory) modulates early precortical sensory processing.

A collaborative approach to supporting communication in the assessment of decision-making capacity.

PubMed

Zuscak, Simon John; Peisah, Carmelle; Ferguson, Alison

2016-01-01

This paper explores the clinical implications of acquired communication disorders in decisional capacity. Discipline-specific contributions are discussed in a multidisciplinary context, with a specific focus on the role of speech and language pathologists (SLPs). Key rehabilitation issues in determining decisional capacity are identified. The impact of communication impairment on capacity is discussed in light of the research literature relating to supportive communication and collaborative practice that respects human rights. Guidelines are presented for professionals involved in the assessment of the decisional capacity of individuals with communication disorders of neurological origin. They guide an assessor through: assessing cognition, language and speech; determining preferred communication domains; and practical strategies and considerations for maximising communication. There is a dearth of guidelines available that deal with augmenting and supporting communication of individuals with acquired communication disorders of neurological origin when it comes to assessing legal decision-making capacity. Capacity assessment is a multidisciplinary realm, and the involvement of SLPs is key to maximising the decision-making capacity of these individuals. All clinicians have an obligation to maximise client autonomy and participation in decision-making. Assessments of capacity should involve a general cognitive ability assessment, followed by a decision-specific assessment tool or question set for the decision facing the patient. The involvement of speech and language pathologists (SLPs) is key to assess and facilitate capacity determinations in instances of cognitive-communication disorder. Impairments in different aspects of auditory comprehension require different accommodations.

A Subgroup Analysis of the Impact of Vortioxetine on Functional Capacity, as Measured by UPSA, in Patients with Major Depressive Disorder and Subjective Cognitive Dysfunction

PubMed Central

Keefe, Richard S E; Nomikos, George; Zhong, Wei; Christensen, Michael Cronquist; Jacobson, William

2018-01-01

Abstract Background We evaluated vortioxetine’s effects on functional capacity in demographic and clinical subgroups of patients with major depressive disorder. Methods This was an exploratory analysis of the CONNECT study (NCT01564862) that evaluated changes in functional capacity using University of California San Diego Performance-based Skills Assessment data, categorized by sex, age, education, employment status, and baseline disease severity (Montgomery-Åsberg Depression Rating Scale, Clinical Global Impressions–Severity of Illness). Results Greater changes in University of California San Diego Performance-based Skills Assessment composite scores were observed with vortioxetine vs placebo in specific subgroups: males (∆+3.2), females (∆+2.9), 45–54 or ≥55 years (∆+5.6, ∆+3.4), working (∆+2.8), high school or greater education (∆+2.7, ∆+2.8), disease severity (Montgomery-Åsberg Depression Rating Scale, <30, ∆+3.5; ≥30, ∆+2.5; Clinical Global Impressions–Severity of Illness ≤4, ∆+2.8; >4, ∆+3.0), major depressive episodes (≤2, >2 [∆+2.7,+3.3]), and episode duration (≤22, >22 weeks [∆+3.7,+2.4]). Conclusions Our findings support the need for additional studies to assess whether vortioxetine improves functional capacity within specific patient subgroups. Clinical Trial Registry clinicaltrials.gov: NCT01564862 PMID:29546401

Assessment of groundwater potential based on aquifer properties of hard rock terrain in the Chittar-Uppodai watershed, Tamil Nadu, India

NASA Astrophysics Data System (ADS)

Kumar, T. Jeyavel Raja; Balasubramanian, A.; Kumar, R. S.; Dushiyanthan, C.; Thiruneelakandan, B.; Suresh, R.; Karthikeyan, K.; Davidraju, D.

2016-06-01

Aquifer performance was tested in 24 locations to assess the groundwater potential of the hard rock terrain in the Chittar-Uppodai watershed of the Tambaraparani River basin. Geologically, the area consists of biotite gneiss, charnockite, and quartzite. The aquifer characteristics, such as transmissivity ( T), the storage coefficient, specific capacity, optimum yield, and the recovery rate were calculated. The drawdown transmissivity was determined using Jacob's straight-line method, while the recovery transmissivity was determined by the Theis method. The drawdown transmissivity was low in the western areas, particularly at Kadayanallur, and was higher in the other areas. The recovery transmissivity was high in the western area, and, with the exception of Gangaikondan, was low at other locations. The assessment indicates that there is groundwater potential in the western part of the study area because of favorable results for recovery drawdown, aquifer thickness, and specific capacity.

Cognitive flexibility in young children: General or task-specific capacity?

PubMed

Deák, Gedeon O; Wiseheart, Melody

2015-10-01

Cognitive flexibility is the ability to adapt to changing tasks or problems. To test whether cognitive flexibility is a coherent cognitive capacity in young children, we tested 3- to 5-year-olds' performance on two forms of task switching, rule-based (Three Dimension Changes Card Sorting, 3DCCS) and inductive (Flexible Induction of Meaning-Animates and Objects, FIM-Ob and FIM-An), as well as tests of response speed, verbal working memory, inhibition, and reasoning. Results suggest that cognitive flexibility is not a globally coherent trait; only the two inductive word-meaning (FIM) tests showed high inter-test coherence. Task- and knowledge-specific factors also determine children's flexibility in a given test. Response speed, vocabulary size, and causal reasoning skills further predicted individual and age differences in flexibility, although they did not have the same predictive relation with all three flexibility tests. Copyright © 2015 Elsevier Inc. All rights reserved.

Binding of /sup 125/I-hCG to rainbow trout (Salmo gairdneri) testis in vitro. [Human Chorionic Gonadotropin

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schlaghecke, R.

1983-02-01

Homogenates of maturing rainbow trout testes show specific binding sites for /sup 125/I-labeled hCG (. /sup 125/I-labeled hCG). The binding is competitively inhibited by unlabeled hCG and by a hypophyseal extract of rainbow trout. It could be demonstrated that the tissue /sup 125/I-hCG binding specificity is restricted to the gonadal preparation. The trout testis was characterized by determining affinity and capacity from Scatchard plot analysis giving a high constant of dissociation Kd 3.65 x 10(-10)/M and a low binding capacity of 0.88 x 10(-15) M/mg tissue. The test system is markedly dependent on temperature, incubation-time, and pH. The maximum bindingmore » was found at 37 degrees during 2 hr of incubation in a buffer of pH 7.5.« less

Lithium/disulfide battery R and D

NASA Astrophysics Data System (ADS)

Kaun, T. D.; Deluca, W.; Lee, J.; Redey, L.; Nelson, P. A.

The focus of molten-salt cell R and D in the past year at Argonne National Laboratory has been on developing an understanding of the excellent performance and stability of a lithium/disulfide cell using LiCl-LiBr-KBr electrolyte. For further improvement, we have initiated development of a rod-electrode cell design and design of cells which can tolerate overdischarge and overcharge abuse. Earlier Li/FeS2 cells offered performance quite below expectations and had high capacity decline rates: 0.10 to 0.25 percent per cycle. Approaches for reducing the capacity decline rates of the earlier cells also reduced cell performance. However, our improved Li/FeS2 cell tests indicate good prospects for attaining cell development goals of specific energy of 200 Wh/kg at a 4-h discharge rate, a specific power of 200 W/kg at 80 percent depth of discharge, and a cycle life of 1000 cycles.

Strengthening Healthcare Capacity Through a Responsive, Country-Specific, Training Standard: The KITSO AIDS Training Program’s Sup-port of Botswana’s National Antiretroviral Therapy Rollout

PubMed Central

Bussmann, Christine; Rotz, Philip; Ndwapi, Ndwapi; Baxter, Daniel; Bussmann, Hermann; Wester, C. William; Ncube, Patricia; Avalos, Ava; Mine, Madisa; Mabe, Elang; Burns, Patricia; Cardiello, Peter; Makhema, Joseph; Marlink, Richard

2008-01-01

In parallel with the rollout of Botswana’s national antiretroviral therapy (ART) program, the Botswana Ministry of Health established the KITSO AIDS Training Program by entering into long-term partnerships with the Botswana–Harvard AIDS Institute Partnership for HIV Research and Education and others to provide standardized, country-specific training in HIV/AIDS care. The KITSO training model has strengthened human capacity within Botswana’s health sector and been indispensable to successful ART rollout. Through core and advanced training courses and clinical mentoring, different cadres of health care workers have been trained to provide high-quality HIV/AIDS care at all ART sites in the country. Continuous and standardized clinical education will be crucial to sustain the present level of care and successfully address future treatment challenges. PMID:18923699

Development of Nanosized/Nanostructured Silicon as Advanced Anodes for Lithium-Ion Cells

NASA Technical Reports Server (NTRS)

Wu, James J.

2015-01-01

NASA is developing high energy and high capacity Li-ion cell and battery designs for future exploration missions under the NASA Advanced Space Power System (ASPS) Program. The specific energy goal is 265 Wh/kg at 10 C. center dot Part of effort for NASA advanced Li-ion cells ? Anode: Silicon (Si) as an advanced anode. ? Electrolyte: advanced electrolyte with flame-retardant additives for enhanced performance and safety (NASA JPL).

Study on casing treatment and stator matching on multistage fan

NASA Astrophysics Data System (ADS)

Wu, Chuangliang; Yuan, Wei; Deng, Zhe

2017-10-01

Casing treatments are required for expanding the stall margin of multi-stage high-load turbofans designed with high blade-tip Mach numbers and high leakage flow. In the case of a low mass flow, the casing treatment effectively reduces the blockages caused by the leakage flow and enlarges the stall margin. However, in the case of a high mass flow, the casing treatment affects the overall flow capacity of the fan, the thrust when operating at the high speeds usually required by design-point specifications. Herein, we study a two-stage high-load fan with three-dimensional numerical simulations. We use the simulation results to propose a scheme that enlarges the stall margin of multistage high-load fans without sacrificing the flow capacity when operating with a large mass flow. Furthermore, a circumferential groove casing treatment is used and adjustments are made to the upstream stator angle to match the casing treatment. The stall margin is thus increased to 16.3%, with no reduction in the maximum mass flow rate or the design thrust performance.

Regular Arrays of Germanium Nanoparticles Assisted by Thermoset Polymer Composites for High Capacity Lithium Ion Battery

NASA Astrophysics Data System (ADS)

Jo, Gyuha; Park, Moon Jeong

2012-02-01

In recent years Li-batteries have attracted significant interests for a variety of applications such as portable electronics and electric vehicle (EV) batteries due to their high energy densities. Key challenges in advancing the technology lie in specific energy density, the long term cycle properties, and durability at elevated temperature. In present study, we were motivated to prepare high capacity Li-battery by creating regular arrays of germanium nanoparticles (GeNPs, 1600 mAh/g) to replace commercial graphite anode (370 mAh/g). Thermoset polymers were employed to prepare GeNPs/polymer composites with tunable NP loadings and spacings, followed by carbonization process to prepare GeNPs/carbon composite anode material. Due to the large volume change of GeNPs with charge/discharge cycles, the regular arrays of GeNPs are turned out to be a crucial parameter in obtaining enhanced cyclability. The GeNPs/carbon anode materials were cycle tested in a half cell configuration using Lithium foil as a counter electrode and lithium salt doped PS-PEO block copolymers as electrolytes. High capacity and rate capability were achieved, which demonstrate the role of nano-sized and regularly-arrayed anode active materials in obtaining the improved battery performance.

High voltage stability of LiCoO2 particles with a nano-scale Lipon coating

DOE Office of Scientific and Technical Information (OSTI.GOV)

Kim, Yoongu; Veith, Gabriel M; Nanda, Jagjit

2011-01-01

For high-voltage cycling of rechargeable Li batteries, a nano-scale amorphous Li-ion conductor, lithium phosphorus oxynitride (Lipon), has been coated on surfaces of LiCoO{sub 2} particles by combining a RF-magnetron sputtering technique and mechanical agitation of LiCoO{sub 2} powders. LiCoO{sub 2} particles coated with 0.36 wt% ({approx}1 nm thick) of the amorphous Lipon, retain 90% of their original capacity compared to non-coated cathode materials that retain only 65% of their original capacity after more than 40 cycles in the 3.0-4.4 V range with a standard carbonate electrolyte. The reason for the better high-voltage cycling behavior is attributed to reduction in themore » side reactions that cause increase of the cell resistance during cycling. Further, Lipon coated particles are not damaged, whereas uncoated particles are badly cracked after cycling. Extending the charge of Lipon-coated LiCoO{sub 2} to higher voltage enhances the specific capacity, but more importantly the Lipon-coated material is also more stable and tolerant of high voltage excursions. A drawback of Lipon coating, particularly as thicker films are applied to cathode powders, is the increased electronic resistance that reduces the power performance.« less

Allogeneic Mature Human Dendritic Cells Generate Superior Alloreactive Regulatory T Cells in the Presence of IL-15.

PubMed

Litjens, Nicolle H R; Boer, Karin; Zuijderwijk, Joke M; Klepper, Mariska; Peeters, Annemiek M A; Prens, Errol P; Verschoor, Wenda; Kraaijeveld, Rens; Ozgur, Zeliha; van den Hout-van Vroonhoven, Mirjam C; van IJcken, Wilfred F J; Baan, Carla C; Betjes, Michiel G H

2015-06-01

Expansion of Ag-specific naturally occurring regulatory T cells (nTregs) is required to obtain sufficient numbers of cells for cellular immunotherapy. In this study, different allogeneic stimuli were studied for their capacity to generate functional alloantigen-specific nTregs. A highly enriched nTreg fraction (CD4(+)CD25(bright)CD127(-) T cells) was alloantigen-specific expanded using HLA-mismatched immature, mature monocyte-derived dendritic cells (moDCs), or PBMCs. The allogeneic mature moDC-expanded nTregs were fully characterized by analysis of the demethylation status within the Treg-specific demethylation region of the FOXP3 gene and the expression of both protein and mRNA of FOXP3, HELIOS, CTLA4, and cytokines. In addition, the Ag-specific suppressive capacity of these expanded nTregs was tested. Allogeneic mature moDCs and skin-derived DCs were superior in inducing nTreg expansion compared with immature moDCs or PBMCs in an HLA-DR- and CD80/CD86-dependent way. Remarkably, the presence of exogenous IL-15 without IL-2 could facilitate optimal mature moDC-induced nTreg expansion. Allogeneic mature moDC-expanded nTregs were at low ratios (<1:320), potent suppressors of alloantigen-induced proliferation without significant suppression of completely HLA-mismatched, Ag-induced proliferation. Mature moDC-expanded nTregs were highly demethylated at the Treg-specific demethylation region within the FOXP3 gene and highly expressed of FOXP3, HELIOS, and CTLA4. A minority of the expanded nTregs produced IL-10, IL-2, IFN-γ, and TNF-α, but few IL-17-producing nTregs were found. Next-generation sequencing of mRNA of moDC-expanded nTregs revealed a strong induction of Treg-associated mRNAs. Human allogeneic mature moDCs are highly efficient stimulator cells, in the presence of exogenous IL-15, for expansion of stable alloantigen-specific nTregs with superior suppressive function. Copyright © 2015 by The American Association of Immunologists, Inc.

A new cathode material for super-valent battery based on aluminium ion intercalation and deintercalation

PubMed Central

Wang, Wei; Jiang, Bo; Xiong, Weiyi; Sun, He; Lin, Zheshuai; Hu, Liwen; Tu, Jiguo; Hou, Jungang; Zhu, Hongmin; Jiao, Shuqiang

2013-01-01

Due to their small footprint and flexible siting, rechargeable batteries are attractive for energy storage systems. A super-valent battery based on aluminium ion intercalation and deintercalation is proposed in this work with VO2 as cathode and high-purity Al foil as anode. First-principles calculations are also employed to theoretically investigate the crystal structure change and the insertion-extraction mechanism of Al ions in the super-valent battery. Long cycle life, low cost and good capacity are achieved in this battery system. At the current density of 50 mAg−1, the discharge capacity remains 116 mAhg−1 after 100 cycles. Comparing to monovalent Li-ion battery, the super-valent battery has the potential to deliver more charges and gain higher specific capacity. PMID:24287676

[Age-specific dynamics of mental working capacity in different regimens of locomotor activity].

PubMed

Miakotnykh, V V; Khodasevich, L S

2012-01-01

The present study included a total of 392 practically healthy men aged between 40 and 79 years differing in the character of routine locomotor activity and the training status (from masters of sport of international grade to the subjects who had never been engaged in sporting activities). They were divided into 4 groups each comprised of subjects ranged by age with a ten-year interval. Their mental working capacity was estimated from the results of the correction test. The study demonstrated that the subjects characterized by a high level of day-to-day locomotor activity have higher indices of attention intensity and information processing speed compared with the age-matched ones leading a relatively sedentary lifestyle. Moreover, they have better chances to retain the mental working capacity up to the age of 70 years.

Results of borehole geophysical logging and hydraulic tests conducted in Area D supply wells, former U.S. Naval Air Warfare Center, Warminster, Pennsylvania

USGS Publications Warehouse

Sloto, Ronald A.; Grazul, Kevin E.

1998-01-01

Borehole geophysical logging, aquifer tests, and aquifer-isolation (packer) tests were conducted in four supply wells at the former U.S. Naval Air Warfare Center (NAWC) in Warminster, PA, to identify the depth and yield of water-bearing zones, occurrence of borehole flow, and effect of pumping on nearby wells. The study was conducted as part of an ongoing evaluation of ground-water contamination at the NAWC. Caliper, natural-gamma, single-point resistance, fluid resistivity, and fluid temperature logs and borehole television surveys were run in the supply wells, which range in depth from 242 to 560 ft (feet). Acoustic borehole televiewer and borehole deviation logs were run in two of the wells. The direction and rate of borehole-fluid movement under non-pumping conditions were measured with a high-resolution heatpulse flowmeter. The logs were used to locate water-bearing fractures, determine probable zones of vertical borehole-fluid movement, and determine the depth to set packers. An aquifer test was conducted in each well to determine open-hole specific capacity and the effect of pumping the open borehole on water levels in nearby wells. Specific capacities ranged from 0.21 to 1.7 (gal/min)/ft (gallons per minute per foot) of drawdown. Aquifer-isolation tests were conducted in each well to determine depth-discrete specific capacities and to determine the effect of pumping an individual fracture or fracture zone on water levels in nearby wells. Specific capacities of individual fractures and fracture zones ranged from 0 to 2.3 (gal/min)/ft. Most fractures identified as water-producing or water-receiving zones by borehole geophysical methods produced water when isolated and pumped. All hydrologically active fractures below 250 ft below land surface were identified as water-receiving zones and produced little water when isolated and pumped. In the two wells greater then 540 ft deep, downward borehole flow to the deep water-receiving fractures is caused by a large difference in head (as much as greater then 49 ft) between water-bearing fractured in the upper and lower part of the borehole. Vertical distribution of specific capacity between land surface and 250 ft below land surface is not related to depth.

ELECTRIC IMPEDANCE OF ARBACIA EGGS

PubMed Central

Cole, Kenneth S.; Cole, Robert H.

1936-01-01

The alternating current resistance and capacity of suspensions of unfertilized and fertilized eggs of Arbacia punctulata have been measured at frequencies from 103 to 1.64 x 107 cycles per second. The unfertilized egg has a static plasma membrane capacity of 0.73 µf./cm.2 which is practically independent of frequency. The fertilized egg has a static membrane capacity of 3.1 µf./cm.2 at low frequencies which decreases to a value of 0.55 µf./cm.2 at high frequencies. The decrease follows closely the relaxation dispersion of the dielectric constant if the dissipation of such a system is ignored. It is considered more probable that the effect is due to a fertilization membrane of 3.1 µf./cm.2 capacity lifted 1.5 µ. from the plasma membrane, the interspace having the conductivity of sea water. The suspensions show a frequency-dependent capacity at low frequencies which may be attributable to surface conductance. The equivalent low frequency internal specific resistance of both the unfertilized and fertilized egg is about 186 ohm cm. or about 6 times that of sea water, while the high frequency data extrapolate to a value of about 4 times sea water. There is evidence at the highest frequencies that the current is penetrating the nucleus and other materials in the cytoplasm. If this effect were entirely due to the nucleus it would lead to a very approximate value of 0.1 µf./cm.2 for the capacity of the nuclear membrane. The measurements do not indicate any change in this effect on fertilization. PMID:19872952

Ventilatory threshold may be a more specific measure of aerobic capacity than peak oxygen consumption rate in persons with stroke.

PubMed

Boyne, Pierce; Reisman, Darcy; Brian, Michael; Barney, Brian; Franke, Ava; Carl, Daniel; Khoury, Jane; Dunning, Kari

2017-03-01

After stroke, aerobic deconditioning can have a profound impact on daily activities. This is usually measured by the peak oxygen consumption rate achieved during exercise testing (VO2-peak). However, VO2-peak may be distorted by motor function. The oxygen uptake efficiency slope (OUES) and VO2 at the ventilatory threshold (VO2-VT) could more specifically assess aerobic capacity after stroke, but this has not been tested. To assess the differential influence of motor function on three measures of aerobic capacity (VO2-peak, OUES, and VO2-VT) and to evaluate the inter-rater reliability of VO2-VT determination post-stroke. Among 59 persons with chronic stroke, cross-sectional correlations with motor function (comfortable gait speed [CGS] and lower extremity Fugl-Meyer [LEFM]) were compared between the different aerobic capacity measures, after adjustment for covariates, in order to isolate any distorting effect of motor function. Reliability of VO2-VT determination between three raters was assessed with intra-class correlation (ICC). CGS was moderately correlated with VO2-peak (r = 0.52, p < 0.0001) and weakly correlated with OUES (r = 0.41, p = 0.002) and VO2-VT (r = 0.37, p = 0.01). LEFM was weakly correlated with VO2-peak (r = 0.26, p = 0.055) and very weakly correlated with OUES (r = 0.19, p = 0.17) and VO2-VT (r = 0.14, p = 0.31). Compared to VO2-peak, VO2-VT was significantly less correlated with CGS (r difference = -0.16, p = 0.02). Inter-rater reliability of VO2-VT determination was high (ICC: 0.93, 95% CI: 0.89-0.96). Motor dysfunction appears to artificially lower measured aerobic capacity. VO2-VT seemed to be less distorted than VO2-peak and had good inter-rater reliability, so it may provide more specific assessment of aerobic capacity post-stroke.

Carbon Redox-Polymer-Gel Hybrid Supercapacitors.

PubMed

Vlad, A; Singh, N; Melinte, S; Gohy, J-F; Ajayan, P M

2016-02-26

Energy storage devices that provide high specific power without compromising on specific energy are highly desirable for many electric-powered applications. Here, we demonstrate that polymer organic radical gel materials support fast bulk-redox charge storage, commensurate to surface double layer ion exchange at carbon electrodes. When integrated with a carbon-based electrical double layer capacitor, nearly ideal electrode properties such as high electrical and ionic conductivity, fast bulk redox and surface charge storage as well as excellent cycling stability are attained. Such hybrid carbon redox-polymer-gel electrodes support unprecedented discharge rate of 1,000C with 50% of the nominal capacity delivered in less than 2 seconds. Devices made with such electrodes hold the potential for battery-scale energy storage while attaining supercapacitor-like power performances.

THE EFFECT OF SI DOPING ON THE ELECTROCHEMICAL CHARACTERISTICS OF LiNixMnyCo(1-x-y)O2

NASA Astrophysics Data System (ADS)

Na, Seong-Hwan; Kim, Hyun-Soo; Moon, Seong-In

A new simple way of synthesizing Li[NiMnCo]O2 was contrived and its electrochemical characteristics were enhanced by Si doping using solution-based synthetic route. The newly synthesized Li[NiMnCo]O2 showed capacity of 175mAh/g and good cycle life at as high cut-off voltage as 4.5V. Si-doping improved the rate capability, specific capacity, and cycle life of the material through increasing lattice parameters and lowering electrochemical impedance.

3D Interconnected Binder-Free Electrospun MnO@C Nanofibers for Supercapacitor Devices.

PubMed

Ramadan, Mohamed; Abdellah, Ahmed M; Mohamed, Saad G; Allam, Nageh K

2018-05-22

Rational design of binder-free materials with high cyclic stability and high conductivity is a great need for high performance supercapacitors. We demonstrate a facile one-step synthesis method of binder-free MnO@C nanofibers as electrodes for supercapacitor applications. The topology of the fabricated nanofibers was investigated using FESEM and HRTEM. The X-ray photoelectron spectroscopy (XPS) and the X-ray diffraction (XRD) analyses confirm the formation of the MnO structure. The electrospun MnO@C electrodes achieve high specific capacitance of 578 F/g at 1 A/g with an outstanding cycling performance. The electrodes also show 127% capacity increasing after 3000 cycles. An asymmetric supercapacitor composed of activated carbon as the negative electrode and MnO@C as the positive electrode shows an ultrahigh energy density of 35.5 Wh/kg with a power density of 1000 W/kg. The device shows a superior columbic efficiency, cycle life, and capacity retention.

Graphene Caging Silicon Particles for High-Performance Lithium-Ion Batteries.

PubMed

Nie, Ping; Le, Zaiyuan; Chen, Gen; Liu, Dan; Liu, Xiaoyan; Wu, Hao Bin; Xu, Pengcheng; Li, Xinru; Liu, Fang; Chang, Limin; Zhang, Xiaogang; Lu, Yunfeng

2018-06-01

Silicon holds great promise as an anode material for lithium-ion batteries with higher energy density; its implication, however, is limited by rapid capacity fading. A catalytic growth of graphene cages on composite particles of magnesium oxide and silicon, which are made by magnesiothermic reduction reaction of silica particles, is reported herein. Catalyzed by the magnesium oxide, graphene cages can be conformally grown onto the composite particles, leading to the formation of hollow graphene-encapsulated Si particles. Such materials exhibit excellent lithium storage properties in terms of high specific capacity, remarkable rate capability (890 mAh g -1 at 5 A g -1 ), and good cycling retention over 200 cycles with consistently high coulombic efficiency at a current density of 1 A g -1 . A full battery test using LiCoO 2 as the cathode demonstrates a high energy density of 329 Wh kg -1 . © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Conductive Polymer Binder-Enabled SiO–Sn xCo yC z Anode for High-Energy Lithium-Ion Batteries

DOE PAGES

Zhao, Hui; Fu, Yanbao; Ling, Min; ...

2016-05-10

In this paper, a SiOSnCoC composite anode is assembled using a conductive polymer binder for the application in next-generation high energy density lithium-ion batteries. A specific capacity of 700 mAh/g is achieved at a 1C (900 mA/g) rate. A high active material loading anode with an areal capacity of 3.5 mAh/cm 2 is demonstrated by mixing SiOSnCoC with graphite. To compensate for the lithium loss in the first cycle, stabilized lithium metal powder (SLMP) is used for prelithiation; when paired with a commercial cathode, a stable full cell cycling performance with a 86% first cycle efficiency is realized. Finally, bymore » achieving these important metrics toward a practical application, this conductive polymer binder/SiOSnCoC anode system presents great promise to enable the next generation of high-energy lithium-ion batteries.« less