SU-E-T-35: A General Fill Factor Definition Serving to Characterise the MLC Misalignment Detection Capabilities of Two-Dimensional Detector Arrays

DOE Office of Scientific and Technical Information (OSTI.GOV)

Stelljes, T.S.; Looe, H.K.; Poppe, B.

Purpose: To present a general definition of the fill factor realistically characterizing the “field coverage”, i.e. the MLC misalignment detection capabilities of a detector array. Methods: According to Gago-Arias et al.{sup 1} the fill factor of a 2D array is defined as the ratio of the area enclosed by the FWHM of the fluence response function KM(x) of a single detector and its cell area defined by the detector spacing. More generally - accounting also for the possible overlap between FWHM’s of neighboured detectors - the fill factor is here defined as that fraction of the sum of the detectormore » cell areas in which a defined MLC misalignment is detectable when the induced percentage signal changes exceed a detection threshold d. Ideally the generalized fill factor may reach 100 %. With user code EGS-chamber and a 2 MeV photon slit beam 0.25 mm wide, both types of the fill factor were calculated for an array with total cell area 100 cm{sup 2} for chamber widths 1–9 mm, using =1mm, d=5%. Results: For single chamber width 5 mm, fill factors were 0.49 (FWHM) and 0.61 (generalized). For chamber width 2 mm the FWHM fill factor was 0.13 whereas the generalized fill factor was 0.32. For chamber widths above 7 mm, the FWHM fill factor exceeds unity, and the general fill factor is exactly 1.00. Conclusions: An updated fill factor definition is introduced which, as a generalization of the FWHM-based definition, more closely estimates the performance of small array chambers and gives a realistic value in the case of overlapping sensitive areas of neighboured chambers. References:{sup 1}A. Gago-Arias, L. Brualla-Gonzalez, D.M. Gonzalez-Castano, F. Gomez, M.S. Garcia, V.L. Vega, J.M. Sueiro, J. Pardo-Montero, “Evaluation of chamber response function influence on IMRT verification using 2D commercial detector arrays,” Phys. Med. Biol. 57, 2005–2020 (2012)« less

Acoustic fill factors for a 120 inch diameter fairing

NASA Technical Reports Server (NTRS)

Lee, Y. Albert

1992-01-01

Data from the acoustic test of a 120-inch diameter payload fairing were collected and an analysis of acoustic fill factors were performed. Correction factors for obtaining a weighted spatial average of the interior sound pressure level (SPL) were derived based on this database and a normalized 200-inch diameter fairing database. The weighted fill factors were determined and compared with statistical energy analysis (VAPEPS code) derived fill factors. The comparison is found to be reasonable.

Interconnect patterns for printed organic thermoelectric devices with large fill factors

NASA Astrophysics Data System (ADS)

Gordiz, Kiarash; Menon, Akanksha K.; Yee, Shannon K.

2017-09-01

Organic materials can be printed into thermoelectric (TE) devices for low temperature energy harvesting applications. The output voltage of printed devices is often limited by (i) small temperature differences across the active materials attributed to small leg lengths and (ii) the lower Seebeck coefficient of organic materials compared to their inorganic counterparts. To increase the voltage, a large number of p- and n-type leg pairs is required for organic TEs; this, however, results in an increased interconnect resistance, which then limits the device output power. In this work, we discuss practical concepts to address this problem by positioning TE legs in a hexagonal closed-packed layout. This helps achieve higher fill factors (˜91%) than conventional inorganic devices (˜25%), which ultimately results in higher voltages and power densities due to lower interconnect resistances. In addition, wiring the legs following a Hilbert spacing-filling pattern allows for facile load matching to each application. This is made possible by leveraging the fractal nature of the Hilbert interconnect pattern, which results in identical sub-modules. Using the Hilbert design, sub-modules can better accommodate non-uniform temperature distributions because they naturally self-localize. These device design concepts open new avenues for roll-to-roll printing and custom TE module shapes, thereby enabling organic TE modules for self-powered sensors and wearable electronic applications.

Mathematical modelling of anisotropy of illite-rich shale

USGS Publications Warehouse

Chesnokov, E.M.; Tiwary, D.K.; Bayuk, I.O.; Sparkman, M.A.; Brown, R.L.

2009-01-01

The estimation of illite-rich shale anisotropy to account for the alignment of clays and gas- or brine-filled cracks is presented via mathematical modelling. Such estimation requires analysis to interpret the dominance of one effect over another. This knowledge can help to evaluate the permeability in the unconventional reservoir, stress orientation, and the seal capacity for the conventional reservoir. Effective media modelling is used to predict the elastic properties of the illite-rich shale and to identify the dominant contributions to the shale anisotropy. We consider two principal reasons of the shale anisotropy: orientation of clay platelets and orientation of fluid-filled cracks. In reality, both of these two factors affect the shale anisotropy. The goal of this study is, first, to separately analyse the effect of these two factors to reveal the specific features in P- and S-wave velocity behaviour typical of each of the factors, and, then, consider a combined effect of the factors when the cracks are horizontally or vertically aligned. To do this, we construct four models of shale. The behaviour of P- and S-wave velocities is analysed when gas- and water-filled cracks embedded in a host matrix are randomly oriented, or horizontally or vertically aligned. The host matrix can be either isotropic or anisotropic (of VTI symmetry). In such a modelling, we use published data on mineralogy and clay platelet alignment along with other micromechanical measurements. In the model, where the host matrix is isotropic, the presence of a singularity point (when the difference VS1 - VS2 changes its sign) in shear wave velocities is an indicator of brine-filled aligned cracks. In the model with the VTI host matrix and horizontally aligned cracks filled with gas, an increase in their volume concentration leads to that the azimuth at which the singularity is observed moves toward the symmetry axis. In this case, if the clay content is small (around 20 per cent), the singularity point may even vanish. The Thomsen parameters are helpful in fluid type indication in shale. An indicator of gas-filled aligned cracks is ?? > ??. If aligned cracks in illite-rich shale are brine-filled, ?? < ??. Negative value of ?? indicates brine-filled cracks in illite-rich shale. A shale with brine-filled cracks exhibits higher Vp/Vs ratio in the vertical direction as compared to the gas-filled shale. A disorientation of clay platelets and brine-filled cracks may lead to that the singularity point is absent for brine-saturated shale as well. In this case one can also observe ?? > ?? and decreased values of Vp/Vs in the vertical direction as in the case of gas-filled cracks. In the presence of vertically aligned cracks, shales exhibit distinctly revealed features of orthorhombic symmetry. The results have important applications where seismic measurements are applied to predict the maturity state of the shale. ?? 2009 The Authors Journal compilation ?? 2009 RAS.

Factors related to presenteeism among employees of the private sector.

PubMed

Mandiracioglu, Aliye; Bolukbas, Osman; Demirel, Mehmet; Gumeli, Filiz

2015-01-01

The objective was to explore the relationship between person-based variables and work-related variables of presenteeism in four different private sector workplaces. Employees (N=413) filled in a questionnaire related to demographic and socio-economic characteristics, social networks, work-related factors, lifestyle factors and state of health. Presenteeism was assessed using the Stanford Presenteeism Scale 6 (SPS-6). The majority of respondents were male (77.2%), and mean age was 34.7±8.1 years. The prevalence of chronic conditions was 15.9%. The mean score for the SPS-6 was 19.9 (SD, 3.3). The female score was higher than the male score on the SPS-6 in this study. Total score was higher among workers who reported working at high speed. SPS-6 score was higher among individuals with a chronic health problem. Understanding of the workplace and personal factors related to presenteeism may support the health and well-being of workers.

Topological approach to quantum Hall effects and its important applications: higher Landau levels, graphene and its bilayer

NASA Astrophysics Data System (ADS)

Jacak, Janusz; Łydżba, Patrycja; Jacak, Lucjan

2017-05-01

In this paper the topological approach to quantum Hall effects is carefully described. Commensurability conditions together with proposed generators of a system braid group are employed to establish the fractional quantum Hall effect hierarchies of conventional semiconductors, monolayer and bilayer graphene structures. Obtained filling factors are compared with experimental data and a very good agreement is achieved. Preliminary constructions of ground-state wave functions in the lowest Landau level are put forward. Furthermore, this work explains why pyramids of fillings from higher bands are not counterparts of the well-known composite-fermion hierarchy - it provides with the cause for an intriguing robustness of ν = 7/3 , 8/3 and 5/2 states (also in graphene). The argumentation why paired states can be developed in two-subband systems (wide quantum wells) only when the Fermi energy lies in the first Landau level is specified. Finally, the paper also clarifies how an additional surface in bilayer systems contributes to an observation of the fractional quantum Hall effect near half-filling, ν = 1/2 .

Adherence to treatment with antipsychotic medication and health care costs among Medicaid beneficiaries with schizophrenia.

PubMed

Gilmer, Todd P; Dolder, Christian R; Lacro, Jonathan P; Folsom, David P; Lindamer, Laurie; Garcia, Piedad; Jeste, Dilip V

2004-04-01

The authors' goal was to evaluate the relationship between adherence to treatment with antipsychotic medication and health expenditures. A secondary objective was to identify risk factors predictive of nonadherence. Data included Medicaid eligibility and claims data from 1998 to 2000 for San Diego County, Calif. Pharmacy records were used to assess adherence to treatment with antipsychotic medication according to the cumulative possession ratio (the number of days medications were available for consumption divided by the number of days subjects were eligible for Medi-Cal). Regression models were used to examine risk factors, hospitalizations, and costs associated with nonadherence, partial adherence, adherence, and excess fills of antipsychotic medication. Forty-one percent of Medicaid beneficiaries with schizophrenia were found to be adherent to treatment with their antipsychotic medications: 24% were nonadherent, 16% were partially adherent, and 19% were excess fillers. Rates of psychiatric hospitalization were lower for those who were adherent (14%) than for those who were nonadherent (35%), partially adherent (24%), or had excess fills (25%). Rates of medical hospitalization were lower for those who were adherent (7%) than for those who were nonadherent (13%) or had excess fills (12%). Those who were adherent had significantly lower hospital costs than the other groups; pharmacy costs were higher among those who were adherent than among those who were nonadherent or partially adherent and were highest for excess fillers. Total costs for excess fillers (14,044 US dollars) were substantially higher than total costs for any other group. Despite the widespread use of atypical antipsychotic medications, alarmingly high rates of both underuse and excessive filling of antipsychotic prescriptions were found in Medicaid beneficiaries with schizophrenia. The high rates of antipsychotic nonadherence and associated negative consequences suggest interventions on multiple levels.

Cultures of Learning in Effective High Schools

ERIC Educational Resources Information Center

Tichnor-Wagner, Ariel; Harrison, Christopher; Cohen-Vogel, Lora

2016-01-01

Purpose: Research indicates that a culture of learning is a key factor in building high schools that foster academic achievement in all students. Yet less is known about which elements of a culture of learning differentiate schools with higher levels of academic performance. To fill this gap, this comparative case study examined the cultures of…

Estimation of Image Sensor Fill Factor Using a Single Arbitrary Image

PubMed Central

Wen, Wei; Khatibi, Siamak

2017-01-01

Achieving a high fill factor is a bottleneck problem for capturing high-quality images. There are hardware and software solutions to overcome this problem. In the solutions, the fill factor is known. However, this is an industrial secrecy by most image sensor manufacturers due to its direct effect on the assessment of the sensor quality. In this paper, we propose a method to estimate the fill factor of a camera sensor from an arbitrary single image. The virtual response function of the imaging process and sensor irradiance are estimated from the generation of virtual images. Then the global intensity values of the virtual images are obtained, which are the result of fusing the virtual images into a single, high dynamic range radiance map. A non-linear function is inferred from the original and global intensity values of the virtual images. The fill factor is estimated by the conditional minimum of the inferred function. The method is verified using images of two datasets. The results show that our method estimates the fill factor correctly with significant stability and accuracy from one single arbitrary image according to the low standard deviation of the estimated fill factors from each of images and for each camera. PMID:28335459

Competition between recombination and extraction of free charges determines the fill factor of organic solar cells

PubMed Central

Bartesaghi, Davide; Pérez, Irene del Carmen; Kniepert, Juliane; Roland, Steffen; Turbiez, Mathieu; Neher, Dieter; Koster, L. Jan Anton

2015-01-01

Among the parameters that characterize a solar cell and define its power-conversion efficiency, the fill factor is the least well understood, making targeted improvements difficult. Here we quantify the competition between charge extraction and recombination by using a single parameter θ, and we demonstrate that this parameter is directly related to the fill factor of many different bulk-heterojunction solar cells. Our finding is supported by experimental measurements on 15 different donor:acceptor combinations, as well as by drift-diffusion simulations of organic solar cells in which charge-carrier mobilities, recombination rate, light intensity, energy levels and active-layer thickness are all varied over wide ranges to reproduce typical experimental conditions. The results unify the fill factors of several very different donor:acceptor combinations and give insight into why fill factors change so much with thickness, light intensity and materials properties. To achieve fill factors larger than 0.8 requires further improvements in charge transport while reducing recombination. PMID:25947637

Evaluation of physicochemical properties of root-end filling materials using conventional and Micro-CT tests.

PubMed

Torres, Fernanda Ferrari Esteves; Bosso-Martelo, Roberta; Espir, Camila Galletti; Cirelli, Joni Augusto; Guerreiro-Tanomaru, Juliane Maria; Tanomaru-Filho, Mario

2017-01-01

To evaluate solubility, dimensional stability, filling ability and volumetric change of root-end filling materials using conventional tests and new Micro-CT-based methods. 7. The results suggested correlated or complementary data between the proposed tests. At 7 days, BIO showed higher solubility and at 30 days, showed higher volumetric change in comparison with MTA (p<0.05). With regard to volumetric change, the tested materials were similar (p>0.05) at 7 days. At 30 days, they presented similar solubility. BIO and MTA showed higher dimensional stability than ZOE (p<0.05). ZOE and BIO showed higher filling ability (p<0.05). ZOE presented a higher dimensional change, and BIO had greater solubility after 7 days. BIO presented filling ability and dimensional stability, but greater volumetric change than MTA after 30 days. Micro-CT can provide important data on the physicochemical properties of materials complementing conventional tests.

Increasing Polymer Solar Cell Fill Factor by Trap-Filling with F4-TCNQ at Parts Per Thousand Concentration.

PubMed

Yan, Han; Manion, Joseph G; Yuan, Mingjian; García de Arquer, F Pelayo; McKeown, George R; Beaupré, Serge; Leclerc, Mario; Sargent, Edward H; Seferos, Dwight S

2016-08-01

Intrinsic traps in organic semiconductors can be eliminated by trap-filling with F4-TCNQ. Photovoltaic tests show that devices with F4-TCNQ at parts per thousand concentration outperform control devices due to an improved fill factor. Further studies confirm the trap-filling pathway and demonstrate the general nature of this finding. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Equilibration of quantum hall edge states and its conductance fluctuations in graphene p-n junctions

NASA Astrophysics Data System (ADS)

Kumar, Chandan; Kuiri, Manabendra; Das, Anindya

2018-02-01

We report an observation of conductance fluctuations (CFs) in the bipolar regime of quantum hall (QH) plateaus in graphene (p-n-p/n-p-n) devices. The CFs in the bipolar regime are shown to decrease with increasing bias and temperature. At high temperature (above 7 K) the CFs vanishes completely and the flat quantized plateaus are recovered in the bipolar regime. The values of QH plateaus are in theoretical agreement based on full equilibration of chiral channels at the p-n junction. The amplitude of CFs for different filling factors follows a trend predicted by the random matrix theory. Although, there are mismatch in the values of CFs between the experiment and theory but at higher filling factors the experimental values become closer to the theoretical prediction. The suppression of CFs and its dependence has been understood in terms of time dependent disorders present at the p-n junctions.

Variability of site response in Seattle, Washington

USGS Publications Warehouse

Hartzell, S.; Carver, D.; Cranswick, E.; Frankel, A.

2000-01-01

Ground motion from local earthquakes and the SHIPS (Seismic Hazards Investigation in Puget Sound) experiment is used to estimate site amplification factors in Seattle. Earthquake and SHIPS records are analyzed by two methods: (1) spectral ratios relative to a nearby site on Tertiary sandstone, and (2) a source/site spectral inversion technique. Our results show site amplifications between 3 and 4 below 5 Hz for West Seattle relative to Tertiary rock. These values are approximately 30% lower than amplification in the Duwamish Valley on artificial fill, but significantly higher than the calculated range of 2 to 2.5 below 5 Hz for the till-covered hills east of downtown Seattle. Although spectral amplitudes are only 30% higher in the Duwamish Valley compared to West Seattle, the duration of long-period ground motion is significantly greater on the artificial fill sites. Using a three-dimensional displacement response spectrum measure that includes the effects of ground-motion duration, values in the Duwamish Valley are 2 to 3 times greater than West Seattle. These calculations and estimates of site response as a function of receiver azimuth point out the importance of trapped surface-wave energy within the shallow, low-velocity, sedimentary layers of the Duwamish Valley. One-dimensional velocity models yield spectral amplification factors close to the observations for till sites east of downtown Seattle and the Duwamish Valley, but underpredict amplifications by a factor of 2 in West Seattle. A two-dimensional finite-difference model does equally well for the till sites and the Duwamish Valley and also yields duration estimates consistent with the observations for the Duwamish Valley. The two-dimensional model, however, still underpredicts amplification in West Seattle by up to a factor of 2. This discrepancy is attributed to 3D effects, including basin-edge-induced surface waves and basin-geometry-focusing effects, caused by the proximity of the Seattle thrust fault and the sediment-filled Seattle basin.

Thermal Conductivity of Epoxy Resin Composites Filled with Combustion Synthesized h-BN Particles.

PubMed

Chung, Shyan-Lung; Lin, Jeng-Shung

2016-05-20

The thermal conductivity of epoxy resin composites filled with combustion-synthesized hexagonal boron nitride (h-BN) particles was investigated. The mixing of the composite constituents was carried out by either a dry method (involving no use of solvent) for low filler loadings or a solvent method (using acetone as solvent) for higher filler loadings. It was found that surface treatment of the h-BN particles using the silane 3-glycidoxypropyltrimethoxysilane (GPTMS) increases the thermal conductivity of the resultant composites in a lesser amount compared to the values reported by other studies. This was explained by the fact that the combustion synthesized h-BN particles contain less -OH or active sites on the surface, thus adsorbing less amounts of GPTMS. However, the thermal conductivity of the composites filled with the combustion synthesized h-BN was found to be comparable to that with commercially available h-BN reported in other studies. The thermal conductivity of the composites was found to be higher when larger h-BN particles were used. The thermal conductivity was also found to increase with increasing filler content to a maximum and then begin to decrease with further increases in this content. In addition to the effect of higher porosity at higher filler contents, more horizontally oriented h-BN particles formed at higher filler loadings (perhaps due to pressing during formation of the composites) were suggested to be a factor causing this decrease of the thermal conductivity. The measured thermal conductivities were compared to theoretical predictions based on the Nielsen and Lewis theory. The theoretical predictions were found to be lower than the experimental values at low filler contents (< 60 vol %) and became increasing higher than the experimental values at high filler contents (> 60 vol %).

Evaluation of physicochemical properties of root-end filling materials using conventional and Micro-CT tests

PubMed Central

TORRES, Fernanda Ferrari Esteves; BOSSO-MARTELO, Roberta; ESPIR, Camila Galletti; CIRELLI, Joni Augusto; GUERREIRO-TANOMARU, Juliane Maria; TANOMARU-FILHO, Mario

2017-01-01

Abstract Objective To evaluate solubility, dimensional stability, filling ability and volumetric change of root-end filling materials using conventional tests and new Micro-CT-based methods. Material and Methods 7 Results The results suggested correlated or complementary data between the proposed tests. At 7 days, BIO showed higher solubility and at 30 days, showed higher volumetric change in comparison with MTA (p<0.05). With regard to volumetric change, the tested materials were similar (p>0.05) at 7 days. At 30 days, they presented similar solubility. BIO and MTA showed higher dimensional stability than ZOE (p<0.05). ZOE and BIO showed higher filling ability (p<0.05). Conclusions ZOE presented a higher dimensional change, and BIO had greater solubility after 7 days. BIO presented filling ability and dimensional stability, but greater volumetric change than MTA after 30 days. Micro-CT can provide important data on the physicochemical properties of materials complementing conventional tests. PMID:28877275

Development of High-Fill-Factor Large-Aperture Micromirrors for Agile Optical Phased Arrays

DTIC Science & Technology

2010-02-28

Final Project Report Contract/Grant Title: Development of High-Fill-Factor Large-Aperture Micromirrors for Agile Optical Phased Arrays...factor (HFF) micromirror array (MMA) has been proposed, fabricated and tested. Optical-phased-array (OPA) beam steering based on the HFF MMA has also...electrically tuned to multiple 2. 1. Background High-fill-factor (HFF) micromirror arrays (MMAs) can form optical phased arrays (OPAs) for laser beam

[The salivary factors related to caries and periodontal disease in children and adolescents with diabetes mellitus].

PubMed

Wang, Meng-xing; Wang, Xin; Zhang, Zhi; Qin, Man

2013-09-01

To detect the salivary factors related to caries and periodontal disease and to analyze the risk of caries and periodontal disease in children and adolescents with diabetes mellitus. The study comprised 30 children with diabetic mellitus, aged 7-15 years old, and 60 healthy age-and gender-matched children. Caries and periodontal indexes were recorded and saliva related factors were analyzed. Caries indexes of diabetes children [permanent teeth: decay missing filling tooth (DMFT) M (Q1,Q3) = 0(0, 4), deciduous teeth: decay missing filling tooth (dmft) M (Q1,Q3) = 0(0, 1)] were not significantly different with those of healthy children [DMFT M (Q1,Q3) = 1(0, 3), dmft M (Q1,Q3) = 0(0, 4)], but plaque index (PLI) (1.25 ± 0.33) and bleeding index (BI) (0.74 ± 0.45) of diabetes children were significantly higher than those of healthy children (PLI was 0.93 ± 0.31,BI was 0.34 ± 0.22) (P < 0.001). Salivary pH of diabetes children (7.68 ± 0.36) was significantly higher than that of healthy children (7.30 ± 0.32) (P < 0.05), and salivary acid buffering capacity had no significant difference between the two groups (P > 0.05). Salivary glucose, immunoglobulin sIgA and sIgG were not significantly different between the two groups (P > 0.05).Salivary lysozyme of diabetes children was significantly higher than that of healthy children (P < 0.05). Total protein was significantly lower in diabetes children than in healthy children (P < 0.05). Salivary lactate dehydrogenase had no significant difference between the two groups (P > 0.05). Diabetes mellitus can lead to the changes of some salivary factors related to gingivitis in diabetes children. Children and adolescents with diabetes mellitus may have a higher risk of periodontal disease.

Limitation of Unloading in the Developing Grains Is a Possible Cause Responsible for Low Stem Non-structural Carbohydrate Translocation and Poor Grain Yield Formation in Rice through Verification of Recombinant Inbred Lines

PubMed Central

Li, Guohui; Pan, Junfeng; Cui, Kehui; Yuan, Musong; Hu, Qiuqian; Wang, Wencheng; Mohapatra, Pravat K.; Nie, Lixiao; Huang, Jianliang; Peng, Shaobing

2017-01-01

Remobilisation of non-structural carbohydrates (NSC) from leaves and stems and unloading into developing grains are essential for yield formation of rice. In present study, three recombinant inbred lines of rice, R91, R156 and R201 have been tested for source-flow-sink related attributes determining the nature of NSC accumulation and translocation at two nitrogen levels in the field. Compared to R91 and R156, R201 had lower grain filling percentage, harvest index, and grain yield. Meanwhile, R201 had significantly lower stem NSC translocation during grain filling stage. Grain filling percentage, harvest index, and grain yield showed the consistent trend with stem NSC translocation among the three lines. In comparison with R91 and R156, R201 had similarity in leaf area index, specific leaf weight, stem NSC concentration at heading, biomass, panicles m-2, spikelets per panicle, remobilization capability of assimilation in stems, sink capacity, sink activity, number and cross sectional area of small vascular bundles, greater number and cross sectional area of large vascular bundles, and higher SPAD, suggesting that source, flow, and sink were not the limiting factors for low stem NSC translocation and grain filling percentage of R201. However, R201 had significant higher stem and rachis NSC concentrations at maturity, which implied that unloading in the developing grains might result in low NSC translocation in R201. The results indicate that stem NSC translocation could be beneficial for enhancement of grain yield potential, and poor unloading into caryopsis may be the possible cause of low stem NSC translocation, poor grain filling and yield formation in R201. PMID:28848573

Influence of fundamental mode fill factor on disk laser output power and laser beam quality

NASA Astrophysics Data System (ADS)

Cheng, Zhiyong; Yang, Zhuo; Shao, Xichun; Li, Wei; Zhu, Mengzhen

2017-11-01

An three-dimensional numerical model based on finite element method and Fox-Li method with angular spectrum diffraction theoy is developed to calculate the output power and power density distribution of Yb:YAG disk laser. We invest the influence of fundamental mode fill factor(the ratio of fundamental mode size and pump spot size) on the output power and laser beam quality. Due to aspherical aberration and soft aperture effect in laser disk, high beam quality can be achieve with relative lower efficiency. The highest output power of fundamental laser mode is influenced by the fundamental mode fill factor. Besides we find that optimal mode fill factor increase with pump spot size.

Extracting Information about the Electronic Quality of Organic Solar-Cell Absorbers from Fill Factor and Thickness

NASA Astrophysics Data System (ADS)

Kaienburg, Pascal; Rau, Uwe; Kirchartz, Thomas

2016-08-01

Understanding the fill factor in organic solar cells remains challenging due to its complex dependence on a multitude of parameters. By means of drift-diffusion simulations, we thoroughly analyze the fill factor of such low-mobility systems and demonstrate its dependence on a collection coefficient defined in this work. We systematically discuss the effect of different recombination mechanisms, space-charge regions, and contact properties. Based on these findings, we are able to interpret the thickness dependence of the fill factor for different experimental studies from the literature. The presented model provides a facile method to extract the photoactive layer's electronic quality which is of particular importance for the fill factor. We illustrate that over the past 15 years, the electronic quality has not been continuously improved, although organic solar-cell efficiencies increased steadily over the same period of time. Only recent reports show the synthesis of polymers for semiconducting films of high electronic quality that are able to produce new efficiency records.

Remotely detected high-field MRI of porous samples

NASA Astrophysics Data System (ADS)

Seeley, Juliette A.; Han, Song-I.; Pines, Alexander

2004-04-01

Remote detection of NMR is a novel technique in which an NMR-active sensor surveys an environment of interest and retains memory of that environment to be recovered at a later time in a different location. The NMR or MRI information about the sensor nucleus is encoded and stored as spin polarization at the first location and subsequently moved to a different physical location for optimized detection. A dedicated probe incorporating two separate radio frequency (RF)—circuits was built for this purpose. The encoding solenoid coil was large enough to fit around the bulky sample matrix, while the smaller detection solenoid coil had not only a higher quality factor, but also an enhanced filling factor since the coil volume comprised purely the sensor nuclei. We obtained two-dimensional (2D) void space images of two model porous samples with resolution less than 1.4 mm 2. The remotely reconstructed images demonstrate the ability to determine fine structure with image quality superior to their directly detected counterparts and show the great potential of NMR remote detection for imaging applications that suffer from low sensitivity due to low concentrations and filling factor.

Flexible Space-Filling Designs for Complex System Simulations

DTIC Science & Technology

2013-06-01

interior of the experimental region and cannot fit higher-order models. We present a genetic algorithm that constructs space-filling designs with...Computer Experiments, Design of Experiments, Genetic Algorithm , Latin Hypercube, Response Surface Methodology, Nearly Orthogonal 15. NUMBER OF PAGES 147...experimental region and cannot fit higher-order models. We present a genetic algorithm that constructs space-filling designs with minimal correlations

Neutron diffraction and thermoelectric properties of indium filled In x Co 4 Sb 12 ( x=0.05, 0.2) and indium cerium filled Ce 0.05 In 0.1 Co 4 Sb 12 skutterudites: Neutron diffraction and thermoelectric properties of In/Ce skutterudites

DOE PAGES

Sesselmann, Andreas; Klobes, Benedikt; Dasgupta, Titas; ...

2015-09-25

The thermoelectric properties on polycrystalline single (In) and double filled (Ce, In) skutterudites are characterized between 300 and 700 K. Powder neutron diffraction measurements of the skutterudite compositions In xCo 4Sb 12 (x= 0.05, 0.2) and Ce 0.05In 0.1Co 4Sb 12 as a function of temperature (12- 300 K) were carried out, which gives more insight into the structural data of single and double-filled skutterudites. Our results show that due to the annealing treatment, a Sb deficiency is detectable and thus verifies defects at the Sb lattice site of the skutterudite. Furthermore, we show by electron microprobe analysis that amore » considerable amount of indium is lost during synthesis and post-processing for the single indium filled samples, but not for the double cerium and indium skutterudite sample. The double-filled skutterudite is superior to the single-filled skutterudite composition due to a higher charge carrier density, a comparable lattice thermal resistivity, and a higher density of states effective mass in our experiment. Finally, we obtained a significantly higher Einstein temperature for the double-filled skutterudite composition in comparison to the single-filled species, which reflects the high sensitivity due to filling of the void lattice position within the skutterudite crystal.« less

Molecular and morphological surface analysis: effect of filling pastes and cleaning agents on root dentin

PubMed Central

DAINEZI, Vanessa Benetello; IWAMOTO, Alexsandra Shizue; MARTIN, Airton Abrahão; SOARES, Luís Eduardo Silva; HOSOYA, Yumiko; PASCON, Fernanda Miori; PUPPIN-RONTANI, Regina Maria

2017-01-01

Abstract The quality of the dentin root is the most important factor for restoration resin sealing and drives the outcome of endodontic treatment. Objective This study evaluated the effect of different filling pastes and cleaning agents on the root dentin of primary teeth using Fourier-transformed Raman spectroscopy (FT-Raman), micro energy-dispersive X-ray fluorescence (µ-EDXRF) and scanning electron microscopic (SEM) analysis. Material and Methods Eighty roots of primary teeth were endodontically prepared and distributed into 4 groups and filled according to the following filling pastes: Control-no filling (CP), Calen®+zinc oxide (CZ), Calcipex II® (CII), Vitapex® (V). After seven days, filling paste groups were distributed to 4 subgroups according to cleaning agents (n=5): Control-no cleaning (C), Ethanol (E), Tergenform® (T), 35% Phosphoric acid (PA). Then, the roots were sectioned and the dentin root sections were internally evaluated by FT-Raman, µ-EDXRF and SEM. Data was submitted to two-way ANOVA and Tukey tests (α=0.05). Results Regarding filling pastes, there was no significant difference in organic content. CP provided the lowest calcium values and, calcium/phosphoric ratio (Ca/P), and the highest phosphoric values. For cleaning agents there was no difference in organic content when compared to the C; however, T showed significantly higher calcium and Ca/P than PA. All groups showed similar results for phosphorus. The dentin smear layer was present after use of the cleaning agents, except PA. Conclusion The filling pastes changed the inorganic content, however they did not change the organic content. Cleaning agents did not alter the inorganic and organic content. PA cleaned and opened dentin tubules. PMID:28198982

Optical properties study of nano-composite filled D shape photonic crystal fibre

NASA Astrophysics Data System (ADS)

Udaiyakumar, R.; Mohamed Junaid, K. A.; Janani, T.; Maheswar, R.; Yupapin, P.; Amiri, I. S.

2018-06-01

With the nano-composite materials gaining momentum in the optical field, a new nano-composite filled D shape Photonic Crystal Fiber (PCF) is designed and the various optical properties are investigated with help of Finite Element Method. In the proposed structure the D-shape PCF is made up of silica with embedded silver nanoparticles and air holes are distributed along the fibre. The designed fibre shows various optical properties such as dispersion, birefringence, beat length and loss with respect to wavelength and compared with different filling factor like 0.1, 0.3 and 0.5. From our estimation and comparative analysis, it has been proved that the fibre loss has been decreased with increasing filling factor. Further this also showed flat dispersion at maximum filling factor.

Benzothiadiazole-based polymer for single and double junction solar cells with high open circuit voltage.

PubMed

Venkatesan, Swaminathan; Ngo, Evan C; Chen, Qiliang; Dubey, Ashish; Mohammad, Lal; Adhikari, Nirmal; Mitul, Abu Farzan; Qiao, Qiquan

2014-06-21

Single and double junction solar cells with high open circuit voltage were fabricated using poly{thiophene-2,5-diyl-alt-[5,6-bis(dodecyloxy)benzo[c][1,2,5]thiadiazole]-4,7-diyl} (PBT-T1) blended with fullerene derivatives in different weight ratios. The role of fullerene loading on structural and morphological changes was investigated using atomic force microscopy (AFM) and X-ray diffraction (XRD). The XRD and AFM measurements showed that a higher fullerene mixing ratio led to breaking of inter-chain packing and hence resulted in smaller disordered polymer domains. When the PBT-T1:PC60BM weight ratio was 1 : 1, the polymer retained its structural order; however, large aggregated domains formed, leading to poor device performance due to low fill factor and short circuit current density. When the ratio was increased to 1 : 2 and then 1 : 3, smaller amorphous domains were observed, which improved photovoltaic performance. The 1 : 2 blending ratio was optimal due to adequate charge transport pathways giving rise to moderate short circuit current density and fill factor. Adding 1,8-diiodooctane (DIO) additive into the 1 : 2 blend films further improved both the short circuit current density and fill factor, leading to an increased efficiency to 4.5% with PC60BM and 5.65% with PC70BM. These single junction solar cells exhibited a high open circuit voltage at ∼ 0.9 V. Photo-charge extraction by linearly increasing voltage (Photo-CELIV) measurements showed the highest charge carrier mobility in the 1 : 2 film among the three ratios, which was further enhanced by introducing the DIO. The Photo-CELIV measurements with varying delay times showed significantly higher extracted charge carrier density for cells processed with DIO. Tandem devices using P3HT:IC60BA as bottom cell and PBT-T1:PC60BM as top cell exhibited a high open circuit voltage of 1.62 V with 5.2% power conversion efficiency.

Small-Molecule Solar Cells with Simultaneously Enhanced Short-Circuit Current and Fill Factor to Achieve 11% Efficiency.

PubMed

Nian, Li; Gao, Ke; Jiang, Yufeng; Rong, Qikun; Hu, Xiaowen; Yuan, Dong; Liu, Feng; Peng, Xiaobin; Russell, Thomas P; Zhou, Guofu

2017-08-01

High-efficiency small-molecule-based organic photovoltaics (SM-OPVs) using two electron donors (p-DTS(FBTTh 2 ) 2 and ZnP) with distinctively different absorption and structural features are reported. Such a combination works well and synergically improves device short-circuit current density (J sc ) to 17.99 mA cm -2 and fill factor (FF) to 77.19%, yielding a milestone efficiency of 11%. To the best of our knowledge, this is the highest power conversion efficiency reported for SM-OPVs to date and the first time to combine high J sc over 17 mA cm -2 and high FF over 77% into one SM-OPV. The strategy of using multicomponent materials, with a selecting role of balancing varied electronic and structural necessities can be an important route to further developing higher performance devices. This development is important, which broadens the dimension and versatility of existing materials without much chemistry input. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Analytical & Experimental Study of Radio Frequency Cavity Beam Profile Monitor

DOE Office of Scientific and Technical Information (OSTI.GOV)

Balcazar, Mario D.; Yonehara, Katsuya

The purpose of this analytical and experimental study is multifold: 1) To explore a new, radiation-robust, hadron beam profile monitor for intense neutrino beam applications; 2) To test, demonstrate, and develop a novel gas-filled Radio-Frequency (RF) cavity to use in this monitoring system. Within this context, the first section of the study analyzes the beam distribution across the hadron monitor as well as the ion-production rate inside the RF cavity. Furthermore a more effecient pixel configuration across the hadron monitor is proposed to provide higher sensitivity to changes in beam displacement. Finally, the results of a benchtop test of themore » tunable quality factor RF cavity will be presented. The proposed hadron monitor configuration consists of a circular array of RF cavities located at a radial distance of 7cm { corresponding to the standard deviation of the beam due to scatering { and a gas-filled RF cavity with a quality factor in the range 400 - 800.« less

Fabrication Processes to Generate Concentration Gradients in Polymer Solar Cell Active Layers

PubMed Central

Inaba, Shusei; Vohra, Varun

2017-01-01

Polymer solar cells (PSCs) are considered as one of the most promising low-cost alternatives for renewable energy production with devices now reaching power conversion efficiencies (PCEs) above the milestone value of 10%. These enhanced performances were achieved by developing new electron-donor (ED) and electron-acceptor (EA) materials as well as finding the adequate morphologies in either bulk heterojunction or sequentially deposited active layers. In particular, producing adequate vertical concentration gradients with higher concentrations of ED and EA close to the anode and cathode, respectively, results in an improved charge collection and consequently higher photovoltaic parameters such as the fill factor. In this review, we relate processes to generate active layers with ED–EA vertical concentration gradients. After summarizing the formation of such concentration gradients in single layer active layers through processes such as annealing or additives, we will verify that sequential deposition of multilayered active layers can be an efficient approach to remarkably increase the fill factor and PCE of PSCs. In fact, applying this challenging approach to fabricate inverted architecture PSCs has the potential to generate low-cost, high efficiency and stable devices, which may revolutionize worldwide energy demand and/or help develop next generation devices such as semi-transparent photovoltaic windows. PMID:28772878

Fabrication Processes to Generate Concentration Gradients in Polymer Solar Cell Active Layers.

PubMed

Inaba, Shusei; Vohra, Varun

2017-05-09

Polymer solar cells (PSCs) are considered as one of the most promising low-cost alternatives for renewable energy production with devices now reaching power conversion efficiencies (PCEs) above the milestone value of 10%. These enhanced performances were achieved by developing new electron-donor (ED) and electron-acceptor (EA) materials as well as finding the adequate morphologies in either bulk heterojunction or sequentially deposited active layers. In particular, producing adequate vertical concentration gradients with higher concentrations of ED and EA close to the anode and cathode, respectively, results in an improved charge collection and consequently higher photovoltaic parameters such as the fill factor. In this review, we relate processes to generate active layers with ED-EA vertical concentration gradients. After summarizing the formation of such concentration gradients in single layer active layers through processes such as annealing or additives, we will verify that sequential deposition of multilayered active layers can be an efficient approach to remarkably increase the fill factor and PCE of PSCs. In fact, applying this challenging approach to fabricate inverted architecture PSCs has the potential to generate low-cost, high efficiency and stable devices, which may revolutionize worldwide energy demand and/or help develop next generation devices such as semi-transparent photovoltaic windows.

Experimental study on energy absorption of foam filled kraft paper honeycomb subjected to quasi-static uniform compression loading

NASA Astrophysics Data System (ADS)

Abd Kadir, N.; Aminanda, Y.; Ibrahim, M. S.; Mokhtar, H.

2016-10-01

A statistical analysis was performed to evaluate the effect of factor and to obtain the optimum configuration of Kraft paper honeycomb. The factors considered in this study include density of paper, thickness of paper and cell size of honeycomb. Based on three level factorial design, two-factor interaction model (2FI) was developed to correlate the factors with specific energy absorption and specific compression strength. From the analysis of variance (ANOVA), the most influential factor on responses and the optimum configuration was identified. After that, Kraft paper honeycomb with optimum configuration is used to fabricate foam-filled paper honeycomb with five different densities of polyurethane foam as filler (31.8, 32.7, 44.5, 45.7, 52 kg/m3). The foam-filled paper honeycomb is subjected to quasi-static compression loading. Failure mechanism of the foam-filled honeycomb was identified, analyzed and compared with the unfilled paper honeycomb. The peak force and energy absorption capability of foam-filled paper honeycomb are increased up to 32% and 30%, respectively, compared to the summation of individual components.

Commensurability condition and hierarchy of fillings for FQHE in higher Landau levels in conventional 2DEG systems and in graphene—monolayer and bilayer

NASA Astrophysics Data System (ADS)

Jacak, Janusz; Jacak, Lucjan

2016-01-01

The structure of the filling rate hierarchy referred to as the fractional quantum Hall effect is studied in higher Landau levels using the commensurability condition. The hierarchy of fillings that are derived in this manner is consistent with the experimental observations of the first three Landau levels in conventional semiconductor Hall systems. The relative poverty of the fractional structure in higher Landau levels compared with the lowest Landau level is explained using commensurability topological arguments. The commensurability criterion for correlated states for higher Landau levels (with n≥slant 1) including the paired states at half fillings of the spin-subbands of these levels is formulated. The commensurability condition is applied to determine the hierarchy of the fractional fillings of Landau levels in the monolayer and bilayer graphene. Good agreement with current experimental observations of fractional quantum Hall effect in the graphene monolayer and bilayer is achieved. The presence of even denominator rates in the hierarchy for fractional quantum Hall effect in the bilayer graphene is also explained.

Differences in willingness to pay for an extraction, a filling, and cleaning teeth at various levels of oral health-related quality of life, as measured by oral impacts on daily performance, among older adults in Singapore.

PubMed

Nair, Rahul; Yee, Robert

2016-12-01

To examine the differences in Willingness to pay (WTP) for an extraction, a filling, and cleaning of teeth among older adults with varying levels of Oral Health-related Quality of Life (OHQoL). OHQoL has been used extensively to measure utilities as reported by individuals of interest. Currently there are no reports that examine the WTP of individuals at various levels of OHQoL. A convenience sample of adults 60 years or older were recruited. Besides other domains, questionnaires were used to assess WTP (extraction, filling, and cleaning of teeth), OHQoL (using Oral Impacts on Daily Performance-OIDP), McArthur scale, and access to care. Tamil ethnicity was related to higher WTP for an extraction (mean ratio, 1.63-3.98; 95% Confidence Interval [CI]), increase of age in years was related to lower WTP for extraction (mean ratio, 0.96-1.00 [95%CI]) and increasing OIDP score was related to lower WTP for extractions (mean ratio, 0.80-0.99 [95%CI]). Tamil ethnicity was associated with higher WTP for fillings (mean ratio, 2.69-6.44 [95%CI]); higher age in years was associated with lower WTP for fillings (mean ratio, 0.94-0.99 [95%CI]), and higher OIDP scores was trending to be associated to lower WTP for filling (mean ratio, 0.80-1.00 [95%CI]). Tamil Ethnicity was also associated with higher WTP for cleaning (mean ratio, 2.14-7.19 [95%CI]), higher age in years was also associated with cleaning (mean ratio, 0.94-0.99 [95%CI]). Individuals with higher OIDP scores tended to have lower WTP for extraction, filling and cleaning; with significant differences reported for extraction. Copyright © 2016. Published by Elsevier B.V.

High-Efficiency Nonfullerene Polymer Solar Cell Enabling by Integration of Film-Morphology Optimization, Donor Selection, and Interfacial Engineering.

PubMed

Zhang, Xin; Li, Weiping; Yao, Jiannian; Zhan, Chuanlang

2016-06-22

Carrier mobility is a vital factor determining the electrical performance of organic solar cells. In this paper we report that a high-efficiency nonfullerene organic solar cell (NF-OSC) with a power conversion efficiency of 6.94 ± 0.27% was obtained by optimizing the hole and electron transportations via following judicious selection of polymer donor and engineering of film-morphology and cathode interlayers: (1) a combination of solvent annealing and solvent vapor annealing optimizes the film morphology and hence both hole and electron mobilities, leading to a trade-off of fill factor and short-circuit current density (Jsc); (2) the judicious selection of polymer donor affords a higher hole and electron mobility, giving a higher Jsc; and (3) engineering the cathode interlayer affords a higher electron mobility, which leads to a significant increase in electrical current generation and ultimately the power conversion efficiency (PCE).

Performance indicators for carrier-based DPIs: Carrier surface properties for capsule filling and API properties for in vitro aerosolisation.

PubMed

Faulhammer, E; Zellnitz, S; Wutscher, T; Stranzinger, S; Zimmer, A; Paudel, A

2018-01-30

This study investigates engineered carrier, as well as engineered API particles, and shows that there are distinct performance indicators of particle engineering for carrier-based dry powder inhalers (DPIs). Spray dried (SDSS) and jet-milled (JMSS) salbutamol sulphate (SS) was blended with untreated α-lactose monohydrate (LAC_R) and α-lactose monohydrate engineered (LAC_E). Subsequent capsule filling was performed with different process settings on a dosator nozzle capsule filling machine in order to reach a target fill weight of 20-25 mg. To evaluate the performance of the different mixtures, in vitro lung deposition experiments were carried out with a next generation impactor, the emitted dose (ED) and fine particle fraction (FPF) were calculated based on the specification of the European pharmacopoeia. The FPF of micronised powder blends is significantly higher (20%) compared to the FPF of spray dried blends (5%). Compared to API engineering, carrier engineering had a positive effect on the capsule filling performance (weight variability and mean fill weight) at lower compression ratios (setting 1). Results further showed that higher compression ratios appear to be beneficial in terms of capsule filling performance (higher fill weight and less fill weight variation). Concluding, it can be stated that the carrier engineering, or generally carrier properties, govern downstream processing, whereas the API engineering and API properties govern the aerosolisation performance and thereby significantly affect the dose delivery to the lungs. Copyright © 2017 Elsevier B.V. All rights reserved.

Hardness Evaluation of Composite Resins Cured with QTH and LED

PubMed Central

Esmaeili, Behnaz; Safarcherati, Hengameh; Vaezi, Assila

2014-01-01

Background and aims. Today light cured composites are widely used. Physical and mechanical properties of composites are related to the degree of conversion. Light curing unit (LCU) is an important factor for composite polymerization. Aim of this study is evaluation of composite resins hardness using halogen and LED light curing units. Materials and methods. In this study, 30 samples of Filtek Z250 and C-Fill composite resins were provided. Samples were light cured with Ultralume2, Valo and Astralis7. Vickers hardness number (VHN) was measured in 0, 1, 2 mm depth. Statistical analysis used: Data were analysed by SPSS software and compared with each other by T-test, one-way and two-way ANOVA and Post-hoc Tukey test. Results. In Filtek Z250, at top surface, VHN of Ultralume2 was higher than VHN of Valo (P = 0.02) and Astralis7 (P =0.04), but in depth of 1, 2 mm, VHN of Ultralume2 and Astralis7 were almost the same and both LCUs were more than Valo which the difference between Ultralume2 and Valo was significant in depth of 1mm (0.05) and 2mm (0.02). In C-Fill composite, at top surface, Astralis7 showed higher VHN, but in depth of 2 mm, performance of all devices were rather simi-lar. Conclusion. In Z250, which contains camphorquinone initiator, light cure LED Ultra-lume2 with narrow wavelength showed higher hardness number than Valo. In C-fill, in top surface, Astralis7 with more exposure time, resulted higher VHN. But In depth of 2 mm, various light curing devices had rather similar hardness number. PMID:25024838

Reliance on social security benefits by Swedish patients with ill-health attributed to dental fillings: a register-based cohort study.

PubMed

Naimi-Akbar, Aron; Svedberg, Pia; Alexanderson, Kristina; Ekstrand, Jan; Sandborgh-Englund, Gunilla

2012-08-30

Some people attribute their ill health to dental filling materials, experiencing a variety of symptoms. Yet, it is not known if they continue to financially support themselves by work or become reliant on different types of social security benefits. The aim of this study was to analyse reliance on different forms of social security benefits by patients who attribute their poor health to dental filling materials. A longitudinal cohort study with a 13-year follow up. The subjects included were 505 patients attributing their ill health to dental restorative materials, who applied for subsidised filling replacement. They were compared to a cohort of matched controls representing the general population (three controls per patient). Annual individual data on disability pension, sick leave, unemployment benefits, and socio-demographic factors was obtained from Statistics Sweden. Generalized estimating equations were used to test for differences between cohorts in number of days on different types of social security benefits. The cohort of dental filling patients had a significantly higher number of days on sick leave and disability pension than the general population. The test of an overall interaction effect between time and cohort showed a significant difference between the two cohorts regarding both sick leave and disability pension. In the replacement cohort, the highest number of sick-leave days was recorded in the year they applied for subsidised replacement of fillings. While sick leave decreased following the year of application, the number of days on disability pension increased and peaked at the end of follow-up. Ill health related to dental materials is likely to be associated with dependence on social security benefits. Dental filling replacement does not seem to improve workforce participation.

Controlling coulomb interactions in infrared stereometamaterials for unity light absorption

NASA Astrophysics Data System (ADS)

Mudachathi, Renilkumar; Moritake, Yuto; Tanaka, Takuo

2018-05-01

We investigate the influence of near field interactions between the constituent 3D split ring resonators on the absorbance and resonance frequency of a stereo metamaterial based perfect light absorber. The experimental and theoretical analyses reveal that the magnetic resonance red shifts and broadens for both the decreasing vertical and lateral separations of the constituents within the metamaterial lattice, analogous to plasmon hybridization. The strong interparticle interactions for higher density reduce the effective cross-section per resonator, which results in weak light absorption observed in both experimental and theoretical analyses. The red shift of the magnetic resonance with increasing lattice density is an indication of the dominating electric dipole interactions and we analyzed the metamaterial system in an electrostatic point of view to explain the observed resonance shift and decreasing absorption peak. From these analyses, we found that the fill factor introduces two competing factors determining the absorption efficiency such as coulomb interactions between the constituent resonators and their number density in a given array structure. We predicted unity light absorption for a fill factor of 0.17 balancing these two opposing factors and demonstrate an experimental absorbance of 99.5% at resonance with our 3D device realized using residual stress induced bending of 2D patterns.

ECO fill: automated fill modification to support late-stage design changes

NASA Astrophysics Data System (ADS)

Davis, Greg; Wilson, Jeff; Yu, J. J.; Chiu, Anderson; Chuang, Yao-Jen; Yang, Ricky

2014-03-01

One of the most critical factors in achieving a positive return for a design is ensuring the design not only meets performance specifications, but also produces sufficient yield to meet the market demand. The goal of design for manufacturability (DFM) technology is to enable designers to address manufacturing requirements during the design process. While new cell-based, DP-aware, and net-aware fill technologies have emerged to provide the designer with automated fill engines that support these new fill requirements, design changes that arrive late in the tapeout process (as engineering change orders, or ECOs) can have a disproportionate effect on tapeout schedules, due to the complexity of replacing fill. If not handled effectively, the impacts on file size, run time, and timing closure can significantly extend the tapeout process. In this paper, the authors examine changes to design flow methodology, supported by new fill technology, that enable efficient, fast, and accurate adjustments to metal fill late in the design process. We present an ECO fill methodology coupled with the support of advanced fill tools that can quickly locate the portion of the design affected by the change, remove and replace only the fill in that area, while maintaining the fill hierarchy. This new fill approach effectively reduces run time, contains fill file size, minimizes timing impact, and minimizes mask costs due to ECO-driven fill changes, all of which are critical factors to ensuring time-to-market schedules are maintained.

Further understanding on the mechanism of alkyl ketene dimer sizing on the causticized calcium carbonate filled paper and its improvements.

PubMed

Wang, Jian; Dang, Miao; Duan, Chao; Qian, Li

2017-02-01

Causticized calcium carbonate (CCC), a solid waste derived from kraft black recovery process, can be used as an alternative for the conventional precipitated calcium carbonate (PCC). However, the application of the CCC has been limited due to its low sizing efficiency in its filled paper. In this study, the characteristics of the CCC were studied aiming to improve the alkyl ketene dimer (AKD) sizing performances of the CCC filled papers, and the results were compared with those from PCC filled papers. The results showed that the CCC had higher pore structure, higher specific surface area, and more negative charge density than the PCC, thus leading to a higher cationic AKD adsorption onto the CCC filler. The lower AKD sizing efficiency in the CCC filled paper can be explained by the combination of higher AKD adsorption and migration, both of which resulted in preferred AKD adsorption onto/into the CCC fillers, rather than the cellulose fibers. Based on the above, the prior addition of polyamide-polyamine epichlorhydrin (PAE) resin to the CCC filler system was proposed to remedy the related issues, thus improving the sizing efficiency.

Effect of masking phase-only holograms on the quality of reconstructed images.

PubMed

Deng, Yuanbo; Chu, Daping

2016-04-20

A phase-only hologram modulates the phase of the incident light and diffracts it efficiently with low energy loss because of the minimum absorption. Much research attention has been focused on how to generate phase-only holograms, and little work has been done to understand the effect and limitation of their partial implementation, possibly due to physical defects and constraints, in particular as in the practical situations where a phase-only hologram is confined or needs to be sliced or tiled. The present study simulates the effect of masking phase-only holograms on the quality of reconstructed images in three different scenarios with different filling factors, filling positions, and illumination intensity profiles. Quantitative analysis confirms that the width of the image point spread function becomes wider and the image quality decreases, as expected, when the filling factor decreases, and the image quality remains the same for different filling positions as well. The width of the image point spread function as derived from different filling factors shows a consistent behavior to that as measured directly from the reconstructed image, especially as the filling factor becomes small. Finally, mask profiles of different shapes and intensity distributions are shown to have more complicated effects on the image point spread function, which in turn affects the quality and textures of the reconstructed image.

Neurological symptoms among dental assistants: a cross-sectional study

PubMed Central

Moen, BE; Hollund, BE; Riise, T

2008-01-01

Background Dental assistants help the dentist in preparing material for filling teeth. Amalgam was the filling material mostly commonly used in Norway before 1980, and declined to about 5% of all fillings in 2005. Amalgam is usually an alloy of silver, copper, tin and mercury. Copper amalgam, giving particularly high exposure to mercury was used in Norway until 1994. Metallic mercury is neurotoxic. Few studies of the health of dental assistants exist, despite their exposure to mercury. There are questions about the existence of possible chronic neurological symptoms today within this working group, due to this exposure. The aim of this study was to compare the occurrence of neurological symptoms among dental assistants likely to be exposed to mercury from work with dental filling material, compared to similar health personnel with no such exposure. Methods All dental assistants still at work and born before 1970 registered in the archives of a trade union in Hordaland county of Norway were invited to participate (response rate 68%, n = 41), as well as a similar number of randomly selected assistant nurses (response rate 87%, n = 64) in the same age group. The participants completed a self-administered, mailed questionnaire, with questions about demographic variables, life-style factors, musculoskeletal, neurological and psychosomatic symptoms (Euroquest). Results The dental assistants reported significant higher occurrence of neurological symptoms; psychosomatic symptoms, problems with memory, concentration, fatigue and sleep disturbance, but not for mood. This was found by analyses of variance, adjusting for age, education, alcohol consumption, smoking and personality traits. For each specific neurological symptom, adjusted logistic regression analyses were performed, showing that these symptoms were mainly from arms, hands, legs and balance organs. Conclusion There is a possibility that the higher occurrence of neurological symptoms among the dental assistants may be related to their previous work exposure to mercury amalgam fillings. This should be studied further to assess the clinical importance of the reported symptoms. PMID:18485237

Neurological symptoms among dental assistants: a cross-sectional study.

PubMed

Moen, Be; Hollund, Be; Riise, T

2008-05-18

Dental assistants help the dentist in preparing material for filling teeth. Amalgam was the filling material mostly commonly used in Norway before 1980, and declined to about 5% of all fillings in 2005. Amalgam is usually an alloy of silver, copper, tin and mercury. Copper amalgam, giving particularly high exposure to mercury was used in Norway until 1994. Metallic mercury is neurotoxic. Few studies of the health of dental assistants exist, despite their exposure to mercury. There are questions about the existence of possible chronic neurological symptoms today within this working group, due to this exposure. The aim of this study was to compare the occurrence of neurological symptoms among dental assistants likely to be exposed to mercury from work with dental filling material, compared to similar health personnel with no such exposure. All dental assistants still at work and born before 1970 registered in the archives of a trade union in Hordaland county of Norway were invited to participate (response rate 68%, n = 41), as well as a similar number of randomly selected assistant nurses (response rate 87%, n = 64) in the same age group. The participants completed a self-administered, mailed questionnaire, with questions about demographic variables, life-style factors, musculoskeletal, neurological and psychosomatic symptoms (Euroquest). The dental assistants reported significant higher occurrence of neurological symptoms; psychosomatic symptoms, problems with memory, concentration, fatigue and sleep disturbance, but not for mood. This was found by analyses of variance, adjusting for age, education, alcohol consumption, smoking and personality traits. For each specific neurological symptom, adjusted logistic regression analyses were performed, showing that these symptoms were mainly from arms, hands, legs and balance organs. There is a possibility that the higher occurrence of neurological symptoms among the dental assistants may be related to their previous work exposure to mercury amalgam fillings. This should be studied further to assess the clinical importance of the reported symptoms.

[Heart ischemia and psychosomatics: the role of stressful events and lifestyles].

PubMed

Guarneri, Maurizio Giuseppe; Nastri, Laura; Assennato, Pasquale; Li Puma, Angela; Landi, Arianna; Bonanno, Barbara; Maggì, Giovan Battista; Annino, Giuseppe; Bono, Filippa; La Barbera, Daniele

2009-06-01

the aim of our study was to evaluate the role of stressful events, lifestyles and various socio-environmental factors in the beginning of ischemic cardiac diseases, together with cardiovascular factors. 64 patients with recent cardiac ischemia and 64 controls matched 1:1, according to their sex and age, have been evaluated. The study required the filling in of clinico-anamnestic reports and the evaluation of stressful events, using the Holmes Rahe scale. in the 44% of the patients who had a heart ischemia, an emotional striking event occurred few days before, with a 28% incidence of work and family problems. The mean score of the Holmes Rahe Social Readjustment Rating Scale was statistically significantly higher among cases (p<0,05). The percentage of the subjects who experienced a stressful event during the last year was significantly higher among those with an ischemic event even though the heart disease factors were similar in the 2 groups of cases and controls. although the known heart risk factors predispose to ischemic event, our results suggest that stressful and emotional factors play a fundamental role in increasing the risk.

Numerical Investigation of the Effect of the Location of Critical Rock Block Fracture on Crack Evolution in a Gob-side Filling Wall

NASA Astrophysics Data System (ADS)

Li, Xuehua; Ju, Minghe; Yao, Qiangling; Zhou, Jian; Chong, Zhaohui

2016-03-01

Generation, propagation, and coalescence of the shear and tensile cracks in the gob-side filling wall are significantly affected by the location of the fracture of the critical rock block. The Universal Discrete Element Code software was used to investigate crack evolution characteristics in a gob-side filling wall and the parameter calibration process for various strata and the filling wall was clearly illustrated. The cracks in both the filling wall and the coal wall propagate inward in a V-shape pattern with dominant shear cracks generated initially. As the distance between the fracture and the filling wall decreases, the number of cracks in the filling wall decreases, and the stability of the filling wall gradually improves; thus, by splitting the roof rock at the optimal location, the filling wall can be maintained in a stable state. Additionally, we conducted a sensitivity analysis that demonstrated that the higher the coal seam strength, the fewer cracks occur in both the filling wall and the coal wall, and the less failure they experience. With the main roof fracturing into a cantilever structure, the higher the immediate roof strength, the fewer cracks are in the filling wall. With the critical rock block fracturing above the roadway, an optimal strength of the immediate roof can be found that will stabilize the filling wall. This study presents a theoretical investigation into stabilization of the filling wall, demonstrating the significance of pre-splitting the roof rock at a desirable location.

Filling the Pipeline: A Look at Enrollment and Employment Trends in Public Higher Education. Special Report.

ERIC Educational Resources Information Center

American Association of State Colleges and Universities, Washington, DC.

Data from a variety of sources are used to examine enrollment and employment trends in public higher education. U.S. public institutions of higher education are charged with supplying much of the human capital that will power the economy and with filling the pipeline of qualified workers. Data suggest that there are several important "disconnects"…

Prevalence of dental caries in 5-year-old Greek children and the use of dental services: evaluation of socioeconomic, behavioural factors and living conditions.

PubMed

Mantonanaki, Magdalini; Koletsi-Kounari, Haroula; Mamai-Homata, Eleni; Papaioannou, William

2013-04-01

To assess dental caries and use of dental services experience in 5-year-old children attending public kindergartens in Attica, Greece and to examine the influence of certain socioeconomic factors and living conditions as well as dental behaviours and attitudes. In this cross-sectional study, a random and stratified sample of 605 Greek children was examined using decayed, missing, filled tooth surfaces and simplified debris indices. The use of dental services was measured by children's dental visits (any dental visit up to the age of 5 years). Care Index was also calculated. Risk indicators were assessed by a questionnaire. Zero-inflated Poisson and Logistic Regression Analysis were generated to test statistical significant associations. The prevalence of dental caries was 16.5%. Care Index was 32% and dental visits were reported for the 84% of the children. Medium Socio-Economic Level (SEL) was associated with no detectable caries. High SEL was related to decreased decayed, missing, filled teeth values, while female gender and rented houses had the opposite effect. The age of the mother (35-39 years) and the higher SEL were related to higher levels of dental services use. It is suggested that there are differences in the experience of dental caries and use of dental services among preschool children in Attica, which are related to demographic, socioeconomic factors and living conditions. Dental public polices should focus on groups with specific characteristics in order to improve oral health levels of disease-susceptible populations. © 2013 FDI World Dental Federation.

Permanent magnet electron beam ion source/trap systems with bakeable magnets for improved operation conditions

DOE Office of Scientific and Technical Information (OSTI.GOV)

Schmidt, M., E-mail: mike.schmidt@dreebit.com; Zschornack, G.; Kentsch, U.

The magnetic system of a Dresden electron beam ion source (EBIS) generating the necessary magnetic field with a new type of permanent magnet made of high energy density NdFeB-type material operable at temperatures above 100 °C has been investigated and tested. The employment of such kind of magnets provides simplified operation without the time-consuming installation and de-installation procedures of the magnets for the necessary baking of the ion source after commissioning and maintenance work. Furthermore, with the use of a new magnetization technique the geometrical filling factor of the magnetic Dresden EBIS design could be increased to a filling factor ofmore » 100% leading to an axial magnetic field strength of approximately 0.5 T exceeding the old design by 20%. Simulations using the finite element method software Field Precision and their results compared with measurements are presented as well. It could be shown that several baking cycles at temperatures higher than 100 °C did not change the magnetic properties of the setup.« less

Permanent magnet electron beam ion source/trap systems with bakeable magnets for improved operation conditions.

PubMed

Schmidt, M; Zschornack, G; Kentsch, U; Ritter, E

2014-02-01

The magnetic system of a Dresden electron beam ion source (EBIS) generating the necessary magnetic field with a new type of permanent magnet made of high energy density NdFeB-type material operable at temperatures above 100 °C has been investigated and tested. The employment of such kind of magnets provides simplified operation without the time-consuming installation and de-installation procedures of the magnets for the necessary baking of the ion source after commissioning and maintenance work. Furthermore, with the use of a new magnetization technique the geometrical filling factor of the magnetic Dresden EBIS design could be increased to a filling factor of 100% leading to an axial magnetic field strength of approximately 0.5 T exceeding the old design by 20%. Simulations using the finite element method software Field Precision and their results compared with measurements are presented as well. It could be shown that several baking cycles at temperatures higher than 100 °C did not change the magnetic properties of the setup.

Occupational stress and cardiovascular risk factors in high-ranking government officials and office workers.

PubMed

Mirmohammadi, Seyyed Jalil; Taheri, Mahmoud; Mehrparvar, Amir Houshang; Heydari, Mohammad; Saadati Kanafi, Ali; Mostaghaci, Mehrdad

2014-08-01

Cardiovascular diseases are among the most important sources of mortality and morbidity, and have a high disease burden. There are some major well-known risk factors, which contribute to the development of these diseases. Occupational stress is caused due to imbalance between job demands and individual's ability, and it has been implicated as an etiology for cardiovascular diseases. This study was conducted to evaluate the cardiovascular risk factors and different dimensions of occupational stress in high-ranking government officials, comparing an age and sex-matched group of office workers with them. We invited 90 high-ranking officials who managed the main governmental offices in a city, and 90 age and sex-matched office workers. The subjects were required to fill the occupational role questionnaire (Osipow) which evaluated their personal and medical history as well as occupational stress. Then, we performed physical examination and laboratory tests to check for cardiovascular risk factors. Finally, the frequency of cardiovascular risk factors and occupational stress of two groups were compared. High-ranking officials in our study had less work experience in their current jobs and smoked fewer pack-years of cigarette, but they had higher waist and hip circumference, higher triglyceride level, more stress from role overload and responsibility, and higher total stress score. Our group of office workers had more occupational stress because of role ambiguity and insufficiency, but their overall job stress was less than officials. The officials have higher scores in some dimensions of occupational stress and higher overall stress score. Some cardiovascular risk factors were also more frequent in managers.

High-Q silicon-on-insulator slot photonic crystal cavity infiltrated by a liquid

DOE Office of Scientific and Technical Information (OSTI.GOV)

Caër, Charles; Le Roux, Xavier; Cassan, Eric, E-mail: eric.cassan@u-psud.fr

We report the experimental realization of a high-Q slot photonic crystal cavity in Silicon-On-Insulator (SOI) configuration infiltrated by a liquid. Loaded Q-factor of 23 000 is measured at telecom wavelength. The intrinsic quality factor inferred from the transmission spectrum is higher than 200 000, which represents a record value for slot photonic crystal cavities on SOI, whereas the maximum of intensity of the cavity is roughly equal to 20% of the light transmitted in the waveguide. This result makes filled slot photonic crystal cavities very promising for silicon-based light emission and ultrafast nonlinear optics.

Dissolved solids in basin-fill aquifers and streams in the southwestern United States

USGS Publications Warehouse

Anning, David W.; Bauch, Nancy J.; Gerner, Steven J.; Flynn, Marilyn E.; Hamlin, Scott N.; Moore, Stephanie J.; Schaefer, Donald H.; Anderholm, Scott K.; Spangler, Lawrence E.

2007-01-01

The U.S. Geological Survey National Water-Quality Assessment Program performed a regional study in the Southwestern United States (Southwest) to describe the status and trends of dissolved solids in basin-fill aquifers and streams and to determine the natural and human factors that affect dissolved solids. Basin-fill aquifers, which include the Rio Grande aquifer system, Basin and Range basin-fill aquifers, and California Coastal Basin aquifers, are the most extensively used ground-water supplies in the Southwest. Rivers, such as the Colorado, the Rio Grande, and their tributaries, are also important water supplies, as are several smaller river systems that drain internally within the Southwest, or drain externally to the Pacific Ocean in southern California. The study included four components that characterize (1) the spatial distribution of dissolved-solids concentrations in basin-fill aquifers, and dissolved-solids concentrations, loads, and yields in streams; (2) natural and human factors that affect dissolved-solids concentrations; (3) major sources and areas of accumulation of dissolved solids; and (4) trends in dissolved-solids concentrations over time in basin-fill aquifers and streams, and the relation of trends to natural or human factors.

Effect of education intervention on the quality and long-term outcomes of root canal treatment in general practice.

PubMed

Koch, M; Wolf, E; Tegelberg, Å; Petersson, K

2015-07-01

To compare the technical quality and long-term outcomes of root canal treatment by general practitioners of a Swedish Public Dental Service, before and after an endodontic education including Ni-Ti rotary technique (NiTiR). A random sample was compiled, comprising one root filled tooth from each of 830 patients, treated by 69 general practitioners participating in the education: 414 teeth root filled in 2002, pre-education, using primarily stainless steel instrumentation and filling by lateral compaction, and 416 teeth root filled post-education (2005), using mainly NiTiR and single-cone obturation. Follow-up radiographs taken in 2009 were evaluated alongside immediate post-filling radiographs from 2002 to 2005. The density and length of the root fillings were registered. Periapical status was assessed by the Periapical Index (PAI), using two definitions of disease: apical periodontitis (AP) (PAI 3 + 4 + 5) and definite AP (PAI 4 + 5). Tooth survival was registered. Root fillings pre- and post-education were compared using chi-square and Fisher's exact tests. Crude extraction rates per 100 years were calculated for comparison of tooth survival. Explanatory variables (type of tooth, root filling quality, periapical status, marginal bone loss, type and quality of coronal restoration) in relation to the dependent variable (AP at follow-up) were analysed by multivariable logistic regression. Follow-up data were available for 229 (55%) of teeth treated pre- and 288 (69%) treated post-education: both tooth survival (P < 0.001) and root filling quality were significantly higher (P < 0.001) in the latter. However, there was no corresponding improvement in periapical status. Both pre- and post-education, root fillings with definite AP on completion of treatment had significantly higher odds of AP or definite AP at follow-up. For teeth treated post-education, inadequate root filling quality was significantly associated with AP at follow-up. Despite a higher tooth survival rate and a significant improvement in technical quality of root fillings after the education, there was no corresponding improvement in periapical status. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Accurate expressions for solar cell fill factors including series and shunt resistances

NASA Astrophysics Data System (ADS)

Green, Martin A.

2016-02-01

Together with open-circuit voltage and short-circuit current, fill factor is a key solar cell parameter. In their classic paper on limiting efficiency, Shockley and Queisser first investigated this factor's analytical properties showing, for ideal cells, it could be expressed implicitly in terms of the maximum power point voltage. Subsequently, fill factors usually have been calculated iteratively from such implicit expressions or from analytical approximations. In the absence of detrimental series and shunt resistances, analytical fill factor expressions have recently been published in terms of the Lambert W function available in most mathematical computing software. Using a recently identified perturbative relationship, exact expressions in terms of this function are derived in technically interesting cases when both series and shunt resistances are present but have limited impact, allowing a better understanding of their effect individually and in combination. Approximate expressions for arbitrary shunt and series resistances are then deduced, which are significantly more accurate than any previously published. A method based on the insights developed is also reported for deducing one-diode fits to experimental data.

Minnesota retrofit insulation in situ test program

DOE Office of Scientific and Technical Information (OSTI.GOV)

Not Available

1978-06-01

The use of cellulose, glass fiber, rock/slag fiber and urea formaldehyde installed as retrofit insulation materials in residential walls and ceilings was studied. Homes were selected for testing according to the type of retrofit insulation, age of retrofit insulation and whether the retrofit was in the wall or ceiling. The total project was comprised of 22 wall and 48 ceiling samples. Samples of retrofit insulation were taken from an area of three to four square feet in the ceiling or wall of the home. The sample volume was measured, the sample removed and double-sealed in polyethylene bags. The samples weremore » shipped to the laboratory for testing. Laboratory measurements were made of density, moisture content, thermal resistance, and relative flammability of each sample. Additionally, the friability and compressive strength of each urea-formaldehyde foam sample was measured. The following results were obtained. Cellulosic loose fill insulation tests indicated that settling and moisture build-up are not serious problems. Flammability is a concern. Age did not affect the properties of the cellulosic loose fill, but fungal growth was evident. Shrinkage, ranging from 2.5 to 9 percent, averaging 4.5 percent, was exhibited. Degradation of the foam samples with time did not occur. Density was the most critical property affecting the other properties. The higher the density, the higher the thermal resistence per inch, the lower the friability and the higher the compressive strength. The accurate prediction of the fiber diameter, amount of unfiberized mineral, and extent of modular clumping thermal resistance of loose fill mineral fiber insulations is related to and is not solely a factor of density. The materials in this sample did not noticeably affect the structure or wiring of the retrofitted homes. (LCL)« less

Biomonitoring of DNA damage in peripheral blood lymphocytes of subjects with dental restorative fillings.

PubMed

Di Pietro, Angela; Visalli, Giuseppa; La Maestra, Sebastiano; Micale, Rosanna; Baluce, Barbara; Matarese, Giovanni; Cingano, Luciano; Scoglio, Maria Elena

2008-02-29

Dental fillings provide a major iatrogenic exposure to xenobiotic compounds due to the high prevalence of surface restorations in developed countries. Experimental data suggest that both amalgams, which contain mercury, and resin-based dental materials cause an impairment of the cellular pro- and anti-oxidant redox balance. The aim of this study was to assess the potential genotoxicity of dental restorative compounds in peripheral blood lymphocytes of young exposed subjects compared with controls. The study examined, by use of the comet assay, 68 carefully selected subjects taking into account the major known confounding factors. In the 44 exposed subjects, the mean numbers of restored surfaces was 3.0 and 3.8 in males and females, respectively. Tail length, percentage of DNA in the tail, tail moment or Olive tail moment were twofold higher in the exposed group than in unexposed controls, with significant differences. No significant difference was observed between amalgam and composite fillings. Furthermore, as shown by multivariate analysis, the association between dental fillings and DNA damage was enhanced by the number of fillings and by the exposure time. Among the lifestyle variables, a moderate physical activity showed a protective effect, being inversely correlated to the DNA damage parameters evaluated. On the whole, the use of DNA-migration allowed us to detect for the first time the potential adverse impact on human health of both kinds of dental filling constituents, the amalgams and the methacrylates. The main mechanism underlying the genotoxicity of dental restorative materials of various nature may be ascribed to the ability of both amalgams and methacrylates to trigger the generation of cellular reactive oxygen species, able to cause oxidative DNA lesions.

DOE Office of Scientific and Technical Information (OSTI.GOV)

Asahina, Yuta; Kawashima, Tomohisa; Furukawa, Naoko

The formation mechanism of CO clouds observed with the NANTEN2 and Mopra telescopes toward the stellar cluster Westerlund 2 is studied by 3D magnetohydrodynamic simulations, taking into account the interstellar cooling. These molecular clouds show a peculiar shape composed of an arc-shaped cloud on one side of the TeV γ -ray source HESS J1023-575 and a linear distribution of clouds (jet clouds) on the other side. We propose that these clouds are formed by the interaction of a jet with clumps of interstellar neutral hydrogen (H i). By studying the dependence of the shape of dense cold clouds formed bymore » shock compression and cooling on the filling factor of H i clumps, we found that the density distribution of H i clumps determines the shape of molecular clouds formed by the jet–cloud interaction: arc clouds are formed when the filling factor is large. On the other hand, when the filling factor is small, molecular clouds align with the jet. The jet propagates faster in models with small filling factors.« less

Impact of Resolution in Multi-Conjugate Adaptive Optics Systems Using Segmented Mirrors (Preprint)

DTIC Science & Technology

2009-06-01

and 100 percent fill factor. The DM1 influence function for each subaperture is modelled as a rectangle. As the apparent resolution of DM1 in the...modelled as a continuous facesheet. To account for the impact of adjoining actuators, an influence function is applied which essentially smoothes out...continuous DMs.20 Lukin’s influence function is closer to that of Jagourel and Gafford,21 or more simplified than the general higher order Gaussian function

Using Web-Based and Paper-Based Questionnaires for Collecting Data on Fertility Issues Among Female Childhood Cancer Survivors: Differences in Response Characteristics

PubMed Central

Overbeek, Annelies; van der Pal, Helena J; Versluys, A. Birgitta; Bresters, Dorine; van Leeuwen, Flora E; Lambalk, Cornelis B; Kaspers, Gertjan J.L; van Dulmen-den Broeder, Eline

2011-01-01

Background Web-based questionnaires have become increasingly popular in health research. However, reported response rates vary and response bias may be introduced. Objective The aim of this study was to evaluate whether sending a mixed invitation (paper-based together with Web-based questionnaire) rather than a Web-only invitation (Web-based questionnaire only) results in higher response and participation rates for female childhood cancer survivors filling out a questionnaire on fertility issues. In addition, differences in type of response and characteristics of the responders and nonresponders were investigated. Moreover, factors influencing preferences for either the Web- or paper-based version of the questionnaire were examined. Methods This study is part of a nationwide study on reproductive function, ovarian reserve, and risk of premature menopause in female childhood cancer survivors. The Web-based version of the questionnaire was available for participants through the Internet by means of a personalized user name and password. Participants were randomly selected to receive either a mixed invitation (paper-based questionnaire together with log-in details for Web-based questionnaire, n = 137) or a Web-only invitation (log-in details only, n = 140). Furthermore, the latter group could request a paper-based version of the questionnaire by filling out a form. Results Overall response rates were comparable in both randomization groups (83% mixed invitation group vs 89% in Web-only invitation group, P = .20). In addition, participation rates appeared not to differ (66% or 90/137, mixed invitation group vs 59% or 83/140, Web-only invitation group, P =.27). However, in the mixed invitation group, significantly more respondents filled out the paper-based questionnaire compared with the Web-only invitation group (83% or 75/90 and 65% or 54/83, respectively, P = .01). The 44 women who filled out the Web-based version of the questionnaire had a higher educational level than the 129 women who filled out the paper-based version (P = .01). Furthermore, the probability of filling out the Web-based questionnaire appeared to be greater for women who were allocated to the Web-only invitation group (OR = 2.85, 95% CI 1.31 - 6.21), were older (OR = 1.08, 95% CI 1.02 - 1.15), had a higher educational level (OR high vs low = 0.06, 95% CI 0.01 - 0.52), or were students (OR employed vs student = 3.25, 95% CI 1.00 - 10.56). Conclusions Although overall response as well as participation rates to both types of invitations were similar, adding a paper version of a questionnaire to a Web-only invitation resulted in more respondents filling out the paper-based version. In addition, women who were older, had a higher level of education, or were students, were more likely to have filled out the Web-based version of the questionnaire. Given the many advantages of Web-based over paper-based questionnaires, researchers should strongly consider using Web-based questionnaires, although possible response bias when using these types of questionnaires should be taken into account. Trial Registration Nederlands Trial Register NTR2922; http://www.trialregister.nl/trialreg/admin/rctview.asp?TC=2922 (Archived by WebCite at http://www.webcitation.org/5zRRdMrDv) PMID:21955527

Using web-based and paper-based questionnaires for collecting data on fertility issues among female childhood cancer survivors: differences in response characteristics.

PubMed

van den Berg, Marleen H; Overbeek, Annelies; van der Pal, Helena J; Versluys, A Birgitta; Bresters, Dorine; van Leeuwen, Flora E; Lambalk, Cornelis B; Kaspers, Gertjan J L; van Dulmen-den Broeder, Eline

2011-09-29

Web-based questionnaires have become increasingly popular in health research. However, reported response rates vary and response bias may be introduced. The aim of this study was to evaluate whether sending a mixed invitation (paper-based together with Web-based questionnaire) rather than a Web-only invitation (Web-based questionnaire only) results in higher response and participation rates for female childhood cancer survivors filling out a questionnaire on fertility issues. In addition, differences in type of response and characteristics of the responders and nonresponders were investigated. Moreover, factors influencing preferences for either the Web- or paper-based version of the questionnaire were examined. This study is part of a nationwide study on reproductive function, ovarian reserve, and risk of premature menopause in female childhood cancer survivors. The Web-based version of the questionnaire was available for participants through the Internet by means of a personalized user name and password. Participants were randomly selected to receive either a mixed invitation (paper-based questionnaire together with log-in details for Web-based questionnaire, n = 137) or a Web-only invitation (log-in details only, n = 140). Furthermore, the latter group could request a paper-based version of the questionnaire by filling out a form. Overall response rates were comparable in both randomization groups (83% mixed invitation group vs 89% in Web-only invitation group, P = .20). In addition, participation rates appeared not to differ (66% or 90/137, mixed invitation group vs 59% or 83/140, Web-only invitation group, P =.27). However, in the mixed invitation group, significantly more respondents filled out the paper-based questionnaire compared with the Web-only invitation group (83% or 75/90 and 65% or 54/83, respectively, P = .01). The 44 women who filled out the Web-based version of the questionnaire had a higher educational level than the 129 women who filled out the paper-based version (P = .01). Furthermore, the probability of filling out the Web-based questionnaire appeared to be greater for women who were allocated to the Web-only invitation group (OR = 2.85, 95% CI 1.31-6.21), were older (OR = 1.08, 95% CI 1.02-1.15), had a higher educational level (OR high vs low = 0.06, 95% CI 0.01-0.52), or were students (OR employed vs student = 3.25, 95% CI 1.00-10.56). Although overall response as well as participation rates to both types of invitations were similar, adding a paper version of a questionnaire to a Web-only invitation resulted in more respondents filling out the paper-based version. In addition, women who were older, had a higher level of education, or were students, were more likely to have filled out the Web-based version of the questionnaire. Given the many advantages of Web-based over paper-based questionnaires, researchers should strongly consider using Web-based questionnaires, although possible response bias when using these types of questionnaires should be taken into account. Nederlands Trial Register NTR2922; http://www.trialregister.nl/trialreg/admin/rctview.asp?TC=2922 (Archived by WebCite at http://www.webcitation.org/5zRRdMrDv).

Effective use of fly ash slurry as fill material.

PubMed

Horiuchi, S; Kawaguchi, M; Yasuhara, K

2000-09-15

A lot of effort has been put into increasing coal ash utilization; however, 50% of total amount is disposed of on land and in the sea. Several attempts have been reported recently concerning slurried coal fly ash use for civil engineering materials, such as for structural fill and backfill. The authors have studied this issue for more than 15 years and reported its potential for (1) underwater fills, (2) light weight backfills, and (3) light weight structural fills, through both laboratory tests and construction works. This paper is an overview of the results obtained for slurry, focusing on the following. (1) Coal fly ash reclaimed by slurry placement shows lower compressibility, higher ground density, and higher strength than by the other methods. This higher strength increases stability against liquefaction during earthquake. (2) Higher stability of the fly ash ground formed by slurry placement is caused by higher density and its self-hardening property. (3) Stability of fly ash reclaimed ground can be increased by increasing density and also by strength enhancement by cement addition. (4) Technical data obtained through a man-made island construction project shows the advantages of fly ash slurry in terms of mechanical properties such as higher stability against sliding failure, sufficient ground strength, and also in terms of cost saving. (5) Concentration in leachates from the placed slurry is lower than the Japanese environmental law. (6) In order to enlarge the fly ash slurry application toward a lightweight fill, mixtures of air foam, cement and fly ash were examined. Test results shows sufficient durability of this material against creep failure. This material was then used as lightweight structural fill around a high-rise building, and showed sufficient quality. From the above data, it can be concluded that coal fly ash slurry can be effectively utilized in civil engineering projects.

Characterization of Inorganic Filler Content, Mechanical Properties, and Light Transmission of Bulk-fill Resin Composites.

PubMed

Fronza, B M; Ayres, Apa; Pacheco, R R; Rueggeberg, F A; Dias, Cts; Giannini, M

The aims of this study were to characterize inorganic content (IC), light transmission (LT), biaxial flexural strength (BFS), and flexural modulus (FM) of one conventional (layered) and four bulk-fill composites at different depths. Bulk-fill composites tested were Surefil SDR flow (SDR), Filtek Bulk Fill (FBF), Tetric EvoCeram Bulk Fill (TEC), and EverX Posterior (EXP). Herculite Classic (HER) was used as a control. Energy dispersive x-ray analysis and scanning electron microscopy were used to characterize filler particle composition and morphology. The LT through different composite thicknesses (1, 2, 3, and 4 mm) was measured using a laboratory-grade spectral radiometer system (n=5). For the BFS and FM tests, sets of eight stacked composite discs (0.5-mm thick) were prepared simulating bulk filling of a 4-mm-thick increment (n=8). SDR demonstrated larger, irregular particles than those observed in TEC or HER. Filler particles in FBF were spherical, while those in EXP were composed of fiberglass strands. The LT decreased with increased composite thickness for all materials. Bulk-fill composites allowed higher LT than the HER. Furthermore, HER proved to be the unique material, having lower BFS values at deeper regions. SDR, FBF, and TEC bulk-fill composites presented reduced FM with increasing composite depth. The bulk-fill composites investigated exhibited higher LT, independent of different filler content and characteristics. Although an increase in composite thickness reduced LT, the BFS of bulk-fill composites at deeper layers was not compromised.

Ten years on: Is dental general anaesthesia in childhood a risk factor for caries and anxiety?

PubMed Central

Haworth, S.; Dudding, T.; Waylen, A.; Thomas, S. J.; Timpson, N. J.

2017-01-01

Objectives To identify whether dental general anaesthesia (DGA) status is informative in assessing risk of caries or dental anxiety by (a) describing long-term oral health and dental anxiety for people who underwent DGA in childhood and (b) testing whether DGA status in childhood is associated with incident future dental caries or anxiety independently of preconceived risk factors. Design Analysis of prospectively obtained data. Setting An established population based cohort in the UK, the Avon Longitudinal Study of Parents and Children. Participants and methods In total 1,695 participants with dental data in childhood and adolescence were included in analysis. DGA status by age 7 and oral health measures at age 17 were identified from questionnaire data. Main outcome measures Filled or extracted permanent teeth at age 17, Corah Dental Anxiety Scale. Results One hundred and twenty-eight (7.6%) participants underwent DGA in childhood. Individuals who underwent DGA had higher measures of filled or extracted permanent teeth in adolescence (0.36 more affected teeth in fully-adjusted model [95% confidence interval: 0.27, 0.55; P <0.001]). Conclusions DGA in childhood predicts burden of treated caries in adolescence, independently of other risk factors. DGA status may be a clinically useful adjunct in identifying young people at high risk of further disease. PMID:28232699

Ten years on: Is dental general anaesthesia in childhood a risk factor for caries and anxiety?

PubMed

Haworth, S; Dudding, T; Waylen, A; Thomas, S J; Timpson, N J

2017-02-24

Objectives To identify whether dental general anaesthesia (DGA) status is informative in assessing risk of caries or dental anxiety by (a) describing long-term oral health and dental anxiety for people who underwent DGA in childhood and (b) testing whether DGA status in childhood is associated with incident future dental caries or anxiety independently of preconceived risk factors.Design Analysis of prospectively obtained data.Setting An established population based cohort in the UK, the Avon Longitudinal Study of Parents and Children.Participants and methods In total 1,695 participants with dental data in childhood and adolescence were included in analysis. DGA status by age 7 and oral health measures at age 17 were identified from questionnaire data.Main outcome measures Filled or extracted permanent teeth at age 17, Corah Dental Anxiety Scale.Results One hundred and twenty-eight (7.6%) participants underwent DGA in childhood. Individuals who underwent DGA had higher measures of filled or extracted permanent teeth in adolescence (0.36 more affected teeth in fully-adjusted model [95% confidence interval: 0.27, 0.55; P <0.001]).Conclusions DGA in childhood predicts burden of treated caries in adolescence, independently of other risk factors. DGA status may be a clinically useful adjunct in identifying young people at high risk of further disease.

Comparative study of GaN-based ultraviolet LEDs grown on different-sized patterned sapphire substrates with sputtered AlN nucleation layer

NASA Astrophysics Data System (ADS)

Zhou, Shengjun; Hu, Hongpo; Liu, Xingtong; Liu, Mengling; Ding, Xinghuo; Gui, Chengqun; Liu, Sheng; Guo, L. Jay

2017-11-01

GaN-based ultraviolet-light-emitting diodes (UV LEDs) with 375 nm emission were grown on different-sized patterned sapphire substrates (PSSs) with ex situ 15-nm-thick sputtered AlN nucleation layers by metal-organic chemical vapor deposition (MOCVD). It was observed through in situ optical reflectance monitoring that the transition time from a three-dimensional (3D) island to a two-dimensional (2D) coalescence was prolonged when GaN was grown on a larger PSS, owing to a much longer lateral growth time of GaN. The full widths at half-maximum (FWHMs) of symmetric GaN(002) and asymmetric GaN(102) X-ray diffraction (XRD) rocking curves decreased as the PSS size increased. By cross-sectional transmission electron microscopy (TEM) analysis, it was found that the threading dislocation (TD) density in UV LEDs decreased with increasing pattern size and fill factor of the PSS, thereby resulting in a marked improvement in internal quantum efficiency (IQE). Finite-difference time-domain (FDTD) simulations quantitatively demonstrated a progressive decrease in light extraction efficiency (LEE) as the PSS size increased. However, owing to the significantly reduced TD density in InGaN/AlInGaN multiple quantum wells (MQWs) and thus improved IQE, the light output power of the UV LED grown on a large PSS with a fill factor of 0.71 was 131.8% higher than that of the UV LED grown on a small PSS with a fill factor of 0.4, albeit the UV LED grown on a large PSS exhibited a much lower LEE.

Maximum projection designs for computer experiments

DOE Office of Scientific and Technical Information (OSTI.GOV)

Joseph, V. Roshan; Gul, Evren; Ba, Shan

Space-filling properties are important in designing computer experiments. The traditional maximin and minimax distance designs only consider space-filling in the full dimensional space. This can result in poor projections onto lower dimensional spaces, which is undesirable when only a few factors are active. Restricting maximin distance design to the class of Latin hypercubes can improve one-dimensional projections, but cannot guarantee good space-filling properties in larger subspaces. We propose designs that maximize space-filling properties on projections to all subsets of factors. We call our designs maximum projection designs. As a result, our design criterion can be computed at a cost nomore » more than a design criterion that ignores projection properties.« less

Maximum projection designs for computer experiments

DOE PAGES

Joseph, V. Roshan; Gul, Evren; Ba, Shan

2015-03-18

Space-filling properties are important in designing computer experiments. The traditional maximin and minimax distance designs only consider space-filling in the full dimensional space. This can result in poor projections onto lower dimensional spaces, which is undesirable when only a few factors are active. Restricting maximin distance design to the class of Latin hypercubes can improve one-dimensional projections, but cannot guarantee good space-filling properties in larger subspaces. We propose designs that maximize space-filling properties on projections to all subsets of factors. We call our designs maximum projection designs. As a result, our design criterion can be computed at a cost nomore » more than a design criterion that ignores projection properties.« less

Cr(VI)-contaminated groundwater remediation with simulated permeable reactive barrier (PRB) filled with natural pyrite as reactive material: Environmental factors and effectiveness.

PubMed

Liu, Yuanyuan; Mou, Haiyan; Chen, Liqun; Mirza, Zakaria A; Liu, Li

2015-11-15

Permeable reactive barriers (PRBs) are efficient technologies for in situ remediation of contaminated groundwater, the effectiveness of which greatly depends on the reactive media filled. Natural pyrite is an iron sulfide material with a very low content of iron and sulfur, and a mining waste which is a potential material for Cr(VI) immobilization. In this study, we conducted a series of batch tests to research the effects of typical environmental factors on Cr(VI) removal and also simulated PRB filled with natural pyrite to investigate its effectiveness, in order to find a both environmentally and economically fine method for groundwater remediation. Batch tests showed that pH had the significant impact on Cr(VI) removal with an apparently higher efficiency under acidic conditions, and dissolved oxygen (DO) would inhibit Cr(VI) reduction; a relatively high initial Cr(VI) concentration would decrease the rate of Cr(VI) sorption; ionic strength and natural organic matter resulted in no significant effects on Cr(VI) removal. Column tests demonstrated that the simulated PRB with natural pyrite as the reactive media was considerably effective for removing Cr(VI) from groundwater, with a sorption capability of 0.6222 mg Cr per gram of natural pyrite at an initial Cr(VI) concentration of 10mg/L at pH 5.5 in an anoxic environment. Copyright © 2015 Elsevier B.V. All rights reserved.

The prognostic significance of cardiac structure and function in atrial fibrillation: the ENGAGE AF-TIMI 48 Echocardiographic Substudy

PubMed Central

Gupta, Deepak K; Giugliano, Robert P; Ruff, Christian T; Claggett, Brian; Murphy, Sabina; Antman, Elliott; Mercuri, Michele F.; Braunwald, Eugene; Solomon, Scott D

2016-01-01

Background Atrial fibrillation (AF) is associated with increased risk for thromboembolism and death; however, the relationships between cardiac structure and function and adverse outcomes among individuals with AF are incompletely understood. Methods The ENGAGE AF –TIMI 48 study tested the once-daily oral factor Xa inhibitor edoxaban in comparison to warfarin for the prevention of stroke (ischemic or hemorrhagic) or systemic embolism in 21,105 subjects with nonvalvular AF and increased risk for thromboembolic events (CHADS2 ≥ 2). In a prospective substudy of 971 subjects who underwent transthoracic echocardiography at baseline, we used Cox proportional hazards models to evaluate the associations between cardiac structure and function and the risks for death and thromboembolism (ischemic stroke, TIA, or systemic embolism). Results Over a median follow up of 2.5 years, 89 (9.2%) deaths and 48 (4.9%) incident thromboembolic events occurred in 971 subjects. In models adjusted for CHADS2 score, aspirin use, and randomized treatment, larger LV end diastolic volume index (HR: 1.49 [95%CI: 1.16,1.91] per 1 SD [12.9 ml/m2]) and higher LV filling pressures measured by E/′e (HR: 1.32 [95%CI: 1.08,1.61] per 1 SD [4.6]) were independently associated with increased risks for death. E/e′ > 13 significantly improved prediction of death beyond clinical factors alone. No features of cardiac structure and function were independently associated with thromboembolism in this population. Findings were similar when adjusted for CHA2DS2-VASc in place of CHADS2. Conclusions In a contemporary population of patients with atrial fibrillation at increased risk for thromboembolic events, larger LV size and higher filling pressures were significantly associated with increased risk for death, but neither left atrial nor left ventricular measures were associated with thromboembolic risk. LV size and filling pressures may help identify AF patients at increased risk of death. PMID:27106009

Periodic Anderson model with correlated conduction electrons: Variational and exact diagonalization study

NASA Astrophysics Data System (ADS)

Hagymási, I.; Itai, K.; Sólyom, J.

2012-06-01

We investigate an extended version of the periodic Anderson model (the so-called periodic Anderson-Hubbard model) with the aim to understand the role of interaction between conduction electrons in the formation of the heavy-fermion and mixed-valence states. Two methods are used: (i) variational calculation with the Gutzwiller wave function optimizing numerically the ground-state energy and (ii) exact diagonalization of the Hamiltonian for short chains. The f-level occupancy and the renormalization factor of the quasiparticles are calculated as a function of the energy of the f orbital for a wide range of the interaction parameters. The results obtained by the two methods are in reasonably good agreement for the periodic Anderson model. The agreement is maintained even when the interaction between band electrons, Ud, is taken into account, except for the half-filled case. This discrepancy can be explained by the difference between the physics of the one- and higher-dimensional models. We find that this interaction shifts and widens the energy range of the bare f level, where heavy-fermion behavior can be observed. For large-enough Ud this range may lie even above the bare conduction band. The Gutzwiller method indicates a robust transition from Kondo insulator to Mott insulator in the half-filled model, while Ud enhances the quasiparticle mass when the filling is close to half filling.

Effect of customization of master gutta-percha cone on apical control of root filling using different techniques: an ex vivo study.

PubMed

van Zyl, S P; Gulabivala, K; Ng, Y-L

2005-09-01

(i) To compare the prevalence of extrusion of root filling material when placed using different root filling techniques, with or without customization of the master gutta-percha (GP) cone; and (ii) to investigate the effects of some factors influencing root filling extrusion and presence of voids. A total of 180 roots were selected, prepared and randomly allocated to three groups. Five general dental practitioners performed the root fillings; each filled one group of roots (n = 60) using each of three techniques; 'cold lateral compaction' (n = 20), 'warm vertical compaction' (n = 20) and 'continuous-wave' (n = 20) techniques. For each obturation technique, the master GP cone was customized using chloroform in 10 samples. Two groups of the roots were recycled to allow all five operators to fulfill their remit. Two observers, blind to operator and obturation technique, examined the radiographs (master apical file, post-obturation) to determine the presence of root filling extrusion and voids within the apical 5 mm, independently. Root filling extrusion was also confirmed by direct inspection of the root apex after obturation. The data were analysed using logistic regression models. A total of 300 root fillings were performed; nine were excluded from the analysis. Most of the root fillings (80%, n = 233) were placed within 0.5 mm of the working length; only 20% (n = 58) were placed >0.5 mm beyond the working length. The odds of prevalence of extrusion (>0.5 mm) were significantly reduced by about 50% when cold lateral compaction or customization of GP were used. One operator produced 2.5 times more extruded root fillings than others. Curvature & length of root canal, apical size of prepared canal, as well as operator's preferred obturation technique had no significant influence on the prevalence of extrusion. Customization of GP was the sole factor to significantly reduce the prevalence of voids within the apical 5 mm of working length. Root filling extrusion was significantly influenced by 'operator' and was reduced by cold lateral compaction and customization of the master cone. Customization of master cone was the only factor that reduced voids apically.

Xenografts Supplemented with Pamindronate placed in postextraction sockets to avoid crestal bone resorption. Experimental study in Fox hound dogs.

PubMed

Lozano-Carrascal, Naroa; Delgado-Ruiz, Rafael Arcesio; Gargallo-Albiol, Jordi; Maté-Sánchez, José Eduardo; Hernandez Alfaro, Federico; Calvo-Guirado, José Luis

2016-02-01

The aim of the study was to compare the effects of porcine xenografts (MP3(®)) with or without pamindronate for the healing of small and large defects of postextraction sockets. Six beagle dogs were used in the study; second premolars and first molars of the mandible were extracted, small defects (SD) and large defects (LD) were identified. Each defect was measured and randomly filled as follows: SC (small control defects filled with MP3(®) alone), ST (small test defects filled with MP3(®) modified with pamindronate), LC (large control defects filled with MP3(®) alone), LT (large test defects filled with MP3(®) modified with pamindronate). After 4 and 8 weeks, the animals were euthanized and the percentages of new bone formation (NB), residual graft (RG) and connective tissue (CT) were analysed by histology and histomorphometry of undecalcified samples. After 4 weeks, NB formation was higher for ST compared to all groups and for LT compared to LC (P < 0.05); RG was significantly higher in both control groups compared to tests (P < 0.05); and CT was higher in large defects (LC and LT) compared to small defects. After 8 weeks, NB formation was higher for test groups (ST and LT) compared to controls (P < 0.05); RG was significantly higher in both control groups compared to tests (P < 0.05); and CT was higher in large defects (LC and LT) compared to small defects (P < 0.05). Within the limitations of this experimental study, the findings suggest that porcine xenografts modified with pamindronate favours the new bone formation and increased the porcine xenograft substitution/replacement after 4 and 8 weeks of healing. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Laser-filamentation-induced water condensation and snow formation in a cloud chamber filled with different ambient gases.

PubMed

Liu, Yonghong; Sun, Haiyi; Liu, Jiansheng; Liang, Hong; Ju, Jingjing; Wang, Tiejun; Tian, Ye; Wang, Cheng; Liu, Yi; Chin, See Leang; Li, Ruxin

2016-04-04

We investigated femtosecond laser-filamentation-induced airflow, water condensation and snow formation in a cloud chamber filled respectively with air, argon and helium. The mass of snow induced by laser filaments was found being the maximum when the chamber was filled with argon, followed by air and being the minimum with helium. We also discussed the mechanisms of water condensation in different gases. The results show that filaments with higher laser absorption efficiency, which result in higher plasma density, are beneficial for triggering intense airflow and thus more water condensation and precipitation.

Occupational Stress and Cardiovascular Risk Factors in High-Ranking Government Officials and Office Workers

PubMed Central

Mirmohammadi, Seyyed Jalil; Taheri, Mahmoud; Mehrparvar, Amir Houshang; Heydari, Mohammad; Saadati Kanafi, Ali; Mostaghaci, Mehrdad

2014-01-01

Background: Cardiovascular diseases are among the most important sources of mortality and morbidity, and have a high disease burden. There are some major well-known risk factors, which contribute to the development of these diseases. Occupational stress is caused due to imbalance between job demands and individual’s ability, and it has been implicated as an etiology for cardiovascular diseases. Objectives: This study was conducted to evaluate the cardiovascular risk factors and different dimensions of occupational stress in high-ranking government officials, comparing an age and sex-matched group of office workers with them. Patients and Methods: We invited 90 high-ranking officials who managed the main governmental offices in a city, and 90 age and sex-matched office workers. The subjects were required to fill the occupational role questionnaire (Osipow) which evaluated their personal and medical history as well as occupational stress. Then, we performed physical examination and laboratory tests to check for cardiovascular risk factors. Finally, the frequency of cardiovascular risk factors and occupational stress of two groups were compared. Results: High-ranking officials in our study had less work experience in their current jobs and smoked fewer pack-years of cigarette, but they had higher waist and hip circumference, higher triglyceride level, more stress from role overload and responsibility, and higher total stress score. Our group of office workers had more occupational stress because of role ambiguity and insufficiency, but their overall job stress was less than officials. Conclusions: The officials have higher scores in some dimensions of occupational stress and higher overall stress score. Some cardiovascular risk factors were also more frequent in managers. PMID:25389469

Parental perceived neighborhood attributes: associations with active transport and physical activity among 10-12 year old children and the mediating role of independent mobility.

PubMed

De Meester, Femke; Van Dyck, Delfien; De Bourdeaudhuij, Ilse; Cardon, Greet

2014-06-20

During the last decades, the use of active travel modes declined in all age groups. Childhood is a critical time to establish lifelong healthy patterns. To develop effective interventions in this age group, insight in the correlates of health behaviors and the possible mediating factors is necessary. Among children, the role of parents may not be overlooked. Therefore, this study aimed to examine the associations of parental perceptions of neighborhood environmental attributes with active transport and total physical activity in 10-12 year old Belgian boys and girls. Furthermore, this study examined the potential mediating effect of independent mobility on these associations. In the present study, 736 10-12 year old children and their parents from 44 elementary schools in Flanders, Belgium, participated. The children were asked to wear an activity monitor and to fill in a survey questioning demographic factors and the Flemish Physical Activity Questionnaire. The parents filled in a survey concerning demographic factors, the child's level of independent mobility and environmental perceptions (Neighborhood Environmental Walkability Scale). Overall, boys reported more active transport when parents perceived more land use mix diversity, shorter distances to school, good land use mix access, higher residential density and less pleasing neighborhood aesthetics. Higher total physical activity levels were reported when parents perceived shorter distances to school and availability of walking/cycling infrastructure. None of the associations was mediated by independent mobility in boys. Girls reported more active transport when parents perceived higher residential density, more land use mix diversity, shorter distances to school, good land use mix access, available walking/cycling infrastructure and convenient recreational facilities. Girls reported higher total physical activity levels when parents perceived high residential density, good land use mix access, well-maintained and high quality walking/cycling infrastructures and more traffic safety. Independent mobility was found to be an important mediator of these associations in girls. Neighborhood environmental interventions to increase children's active transport and physical activity can be effective when combined with awareness raising programs for parents. Furthermore, among girls encouraging independent mobility may contribute to behavior change.

What happens if we compare chopsticks with forks? The impact of making inappropriate comparisons in cross-cultural research.

PubMed

Chen, Fang Fang

2008-11-01

It is a common practice to export instruments developed in one culture to another. Little is known about the consequences of making inappropriate comparisons in cross-cultural research. Several studies were conducted to fill in this gap. Study 1 examined the impact of lacking factor loading invariance on regression slope comparisons. When factor loadings of a predictor are higher in the reference group (e.g., United States), for which the scale was developed, than in the focal group (e.g., China), into which the scale was imported, the predictive relationship (e.g., self-esteem predicting life satisfaction) is artificially stronger in the reference group but weaker in the focal group, creating a bogus interaction effect of predictor by group (e.g., self-esteem by culture); the opposite pattern is found when the reference group has higher loadings in an outcome variable. Studies 2 and 3 examined the impact of lacking loading and intercept (i.e., point of origin) invariance on factor means, respectively. When the reference group has higher loadings or intercepts, the mean is overestimated in that group but underestimated in the focal group, resulting in a pseudo group difference. (c) 2008 APA, all rights reserved.

Combination film/splash fill for overcoming film fouling

DOE Office of Scientific and Technical Information (OSTI.GOV)

Phelps, P.M.; Minett, T.O.

1995-02-01

In summary, this large cooling tower user has found the Phelps film/splash Stack-Pack fill design to attain a substantial improvement in capability of their existing crossflow cooling towers, without increasing fan power or tower size. The lack of fouling in the film fill component of this fill design is due to the use of film fill with large (1 inch) spacing between sheets, coupled with effective water treatment as provided by Nalco. This combination of factors provides a proven method for significantly increasing crossflow or counterflow cooling tower capability while minimizing chances of serious fill fouling.

Factors affecting DSAEK graft lenticle adhesion: an in vitro experimental study.

PubMed

Vaddavalli, Pravin K; Diakonis, Vasilios F; Canto, Ana P; Kankariya, Vardhaman P; Pappuru, Rajeev R; Ruggeri, Marco; Banitt, Michael R; Kymionis, George D; Yoo, Sonia H

2014-06-01

The aim of this study was to evaluate different factors that affect Descemet stripping automated endothelial keratoplasty (DSAEK) donor graft lenticle adhesion to the recipient cornea. This experimental study included 10 eye bank recipient corneas and 10 donor DSAEK lenticles. Recipient corneas were mounted on an artificial anterior chamber (AC), whereas donor lenticles were placed beneath the host cornea. Using optical coherence tomography and imaging software, the interface gap (IG) between the donor and recipient cornea was quantified to evaluate the effect of variations in AC air fill pressure, AC air fill duration, corneal massage, and corneal venting incisions on DSAEK donor graft lenticle adhesion. Different intraocular pressures (IOP) under air for the same time intervals, do not significantly correlate with the IG; nevertheless, it was noticed that the IG decreases as the IOP increases. With respect to the magnitude of AC IOP, there was no statistically significant difference when comparing 10 mm Hg with 30 mm Hg and assessing IG (P = 0.4). Complete air-fluid exchange resulted in significantly higher IG when compared with AC air bubble of 10 and 30 mm Hg that was sustained for 1 hour (P < 0.05). Furthermore, corneal surface massage did not facilitate DSAEK graft adhesion (P = 0.59). Finally, paracentral venting incisions followed by interface fluid aspiration seemed to significantly decrease the IG (P = 0.014). Corneal venting incisions and higher AC IOP values seem to facilitate DSAEK donor graft lenticle adhesion to the recipient cornea.

Efficiency loss of thin film Cu(InxGa1-x)Se(S) solar panels by lamination process

NASA Astrophysics Data System (ADS)

Xu, Li

2017-04-01

Efficiency loss of thin film Cu(InxGa1-x)Se(S) (CIGS) solar panels by lamination process has been compromising the final output power in commercial products of solar modules, but few reports have been published on such issue, as the majority of the investigation is focused on the efficiency at the circuit level, i.e., before lamination process. In this paper, we studied the effect of lamination process to the efficiency loss of thin film CIGS solar panels. It was observed that the fill factor degradation dominated the efficiency loss with the small change of Voc and Jsc. Experiments showed that neither the temperature nor the pressure, nor the two combined in the lamination process is the root cause of the efficiency loss; instead, the ethylene vinyl acetate (EVA) layer as the encapsulation material which directly contacts the solar cell devices was the major factor responsible for the efficiency loss. It was found that the gel content of the cured EVA film after lamination was highly correlated to the efficiency loss. The higher the gel content, the higher the efficiency loss. The mismatch of coefficient of thermal expansion between the EVA film and the CIGS thin film resulted in compressive stress in the device layer after lamination process. The compressive stress is speculated to affect the lattice defects, but need to be confirmed with the measurement of capacitance voltage (CV) and drive level capacitance profiling (DLCP). Three-day sun soak was then carried out and it was observed that the fill factor recovered significantly and so did the efficiency. Experiments also showed that there was no impact of chemical erosion on the front electrode of transparent conductive oxide (TCO) films by chemicals released from the EVA films during lamination.

Detection of Fractured Endodontic Instruments in Root Canals: Comparison between Different Digital Radiography Systems and Cone-beam Computed Tomography.

PubMed

Ramos Brito, Ana Caroline; Verner, Francielle Silvestre; Junqueira, Rafael Binato; Yamasaki, Mayra Cristina; Queiroz, Polyane Mazucato; Freitas, Deborah Queiroz; Oliveira-Santos, Christiano

2017-04-01

This study compared the detection of fractured instruments in root canals with and without filling by periapical radiographs from 3 digital systems and cone-beam computed tomographic (CBCT) images with different resolutions. Thirty-one human molars (80 canals) were used. Root canals were divided into the following groups: the control group, without fillings; the fracture group, without fillings and with fractured files; the fill group, filled; and the fill/fracture group, filled and with fractured files. Digital radiographs in ortho-, mesio-, and distoradial directions were performed in 2 semidirect systems (VistaScan [Dürr Dental, Beitigheim-Bissinger, Germany] and Express [Instrumentarium Imaging, Tuusula, Finland]) and a direct system (SnapShot [Instrumentarium Imaging]). CBCT images were acquired with 0.085-mm and 0.2-mm voxel sizes. All images were assessed and reassessed by 4 observers for the presence or absence of fractured files on a 5-point scale. The sensitivity, specificity, and accuracy were calculated. In the absence of filling, accuracy values were high, and there were no statistical differences among the radiographic techniques, different digital systems, or the different CBCT voxels sizes. In the presence of filling, the accuracy of periapical radiographs was significantly higher than CBCT images. In general, SnapShot showed higher accuracy than VistaScan and Express. Periapical radiographs in 1 incidence were accurate for the detection of fractured endodontic instruments inside the root canal in the absence or presence of filling, suggesting that this technique should be the first choice as well as the direct digital radiographic system. In the presence of filling, the decision to perform a CBCT examination must take into consideration its low accuracy. Copyright © 2016 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Subsurface evaluation of the west parking lot and landfill 3 areas of Air Force Plant 4, Fort Worth, Texas, using two-dimensional direct-current resistivity profiling

USGS Publications Warehouse

Braun, Christopher L.; Jones, Sonya A.

2002-01-01

During September 1999, the U.S. Geological Survey made 10 two-dimensional direct-current resistivity profile surveys in the west parking lot and landfill 3 areas of Air Force Plant 4, Fort Worth, Texas, to identify subsurface areas of anomalously high or low resistivity that could indicate potential contamination, contaminant pathways, or anthropogenic structures. Six of the 10 surveys (transects) were in the west parking lot. Each of the inverted sections of these transects had anomalously high resistivities in the terrace alluvium/fill (the surficial subsurface layer) that probably were caused by highly resistive fill material. In addition, each of these transects had anomalously low resistivities in the Walnut Formation (a bedrock layer immediately beneath the alluvium/fill) that could have been caused by saturation of fractures within the Walnut Formation. A high-resistivity anomaly in the central part of the study area probably is associated with pea gravel fill used in construction of a French drain. Another high resistivity anomaly in the west parking lot, slightly southeast of the French drain, could be caused by dense nonaqueous-phase liquid in the Walnut Formation. The inverted sections of the four transects in the landfill 3 area tended to have slightly higher resistivities in both the alluvium/fill and the Walnut Formation than the transects in the west parking lot. The higher resistivities in the alluvium/fill could have been caused by drier conditions in grassy areas relative to conditions in the west parking lot. Higher resistivities in parts of the Walnut Formation also could be a function of drier conditions or variations in the lithology of the Walnut Formation. In addition to the 10 vertical sections, four horizontal sections at 2-meteraltitude intervals show generally increasing resistivity with decreasing altitude that most likely results from the increased influence of the Walnut Formation, which has a higher resistivity than the terrace alluvium/fill.

The Surface Brightness Contribution of II Peg: A Comparison of TiO Band Analysis and Doppler Imaging

NASA Astrophysics Data System (ADS)

Senavci, H. V.; O'Neal, D.; Hussain, G. A. J.; Barnes, J. R.

2015-01-01

We investigate the surface brightness contribution of the very well known active SB1 binary II Pegasi , to determine the star spot filling factor and the spot temperature parameters. In this context, we analyze 54 spectra of the system taken over 6 nights in September - October of 1996, using the 2.1m Otto Struve Telescope equipped with SES at the McDonald Observatory. We measure the spot temperatures and spot filling factors by fitting TiO molecular bands in this spectroscopic dataset, with model atmosphere approximation using ATLAS9 and with proxy stars obtained with the same instrument. The same dataset is then used to also produce surface spot maps using the Doppler imaging technique. We compare the spot filling factors obtained with the two independent techniques in order to better characterise the spot properties of the system and to better assess the limitations inherent to both techniques. The results obtained from both techniques show that the variation of spot filling factor as a function of phase agree well with each other, while the amount of TiO and DI spot

Protein aggregation studied by forward light scattering and light transmission analysis

NASA Astrophysics Data System (ADS)

Penzkofer, A.; Shirdel, J.; Zirak, P.; Breitkreuz, H.; Wolf, E.

2007-12-01

The aggregation of the circadian blue-light photo-receptor cryptochrome from Drosophila melanogaster (dCry) is studied by transmission and forward light scattering measurement in the protein transparent wavelength region. The light scattering in forward direction is caused by Rayleigh scattering which is proportional to the degree of aggregation. The light transmission through the samples in the transparent region is reduced by Mie light scattering in all directions. It depends on the degree of aggregation and the monomer volume fill factor of the aggregates (less total scattering with decreasing monomer volume fill factor of protein globule) allowing a distinction between tightly packed protein aggregation (monomer volume fill factor 1) and loosely packed protein aggregation (monomer volume fill factor less than 1). An increase in aggregation with temperature, concentration, and blue-light exposure is observed. At a temperature of 4 °C and a protein concentration of less than 0.135 mM no dCry aggregation was observed, while at 24 °C and 0.327 mM gelation occurred (loosely packed aggregates occupying the whole solution volume).

The effects of alkanolamide addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR) / chloroprene rubber (CR) blends

NASA Astrophysics Data System (ADS)

Surya, Indra; Fauzi Siregar, Syahrul; Ismail, Hanafi

2018-03-01

Effects of alkanolamide (ALK) addition on cure characteristics, swelling behaviour and tensile properties of silica-filled natural rubber (NR)/chloroprene rubber (CR) blends were investigated. The ALK was synthesized from Refined Bleached Deodorized Palm Stearin (RBDPS) and diethanolamine, and incorporated into the silica-filled NR/CR blends as a non-toxic rubber additive. The ALK loadings were 0.0, 1.0, 3.0, 5.0 and 7.0 phr. It was found that the ALK exhibited shorter scorch and cure times and higher elongation at break of the silica-filled NR/CR blends. The ALK also exhibited higher torque differences, tensile modulus and tensile strength at a 1.0 phr of ALK loading and then decreased with further increases in the ALK loading. The swelling measurement proved that the 1.0 phr loading of ALK caused the highest degree in crosslink density of the silica-filled NR/CR blends.

Parametric Study of Fire Performance of Concrete Filled Hollow Steel Section Columns with Circular and Square Cross-Section

NASA Astrophysics Data System (ADS)

Nurfaidhi Rizalman, Ahmad; Tahir, Ng Seong Yap Mahmood Md; Mohammad, Shahrin

2018-03-01

Concrete filled hollow steel section column have been widely accepted by structural engineers and designers for high rise construction due to the benefits of combining steel and concrete. The advantages of concrete filled hollow steel section column include higher strength, ductility, energy absorption capacity, and good structural fire resistance. In this paper, comparison on the fire performance between circular and square concrete filled hollow steel section column is established. A three-dimensional finite element package, ABAQUS, was used to develop the numerical model to study the temperature development, critical temperature, and fire resistance time of the selected composite columns. Based on the analysis and comparison of typical parameters, the effect of equal cross-sectional size for both steel and concrete, concrete types, and thickness of external protection on temperature distribution and structural fire behaviour of the columns are discussed. The result showed that concrete filled hollow steel section column with circular cross-section generally has higher fire resistance than the square section.

[Experimental study on the transforming growth factor β3 combined with dental pulp stem cells in early bone integration of implant].

PubMed

Guzalinuer, Ababaikeli; Muhetaer, Huojia; Wu, H; Paerhati, Abudureheman

2018-04-09

Objective: To establish the experimental model of rabbit mandibular anterior implant repair and evaluate the effects of transforming growth factor (TGF)-β3 and dental pulp stem cells (DPSC) in promoting the bone integration of implant. Methods: The New Zealand rabbits were randomly divided into experimental group, control group and blank group (6 rabbits for each group) . In the experimental group, the implant area was filled with the mixture of TGF-β3, DPSC and Bio-oss powder. In the control group, the implant area was filled with the mixture of DPSC and Bio-oss powder. In the blank group, the implant area was filled with the mixture of phosphate buffer solution and Bio-oss powder. Eighteen New Zealand rabbits were sacrificed in 2 weeks after procedure. The treated alveolar bone tissue was observed. The bone tissue around the implant were estimated by HE staining, immunocytochemical staining and real-time quantitative PCR. Results: The implants were no shedding nor loose. HE staining shows the blank group had a sparse trabecular bone and a small amount of blood vessel around the implant and no obvious new bone formation. The control group showed that the bone trabecula around the implant was sparse and slender, the osteoblasts were arranged linearly around the trabecular bone, a small amount of new bone formation was found around the implant. In the experimental group, there were more thick and dense trabecular bone around the implant, the surrounding osteoblasts were arranged in clusters. The osteoblasts were active and many new bone formed. Typical bone lacunae, bone cells and a large number of new blood vessels can be observed. Immunohistochemistry showed that the proportion of average positive area in the experimental group, control group, blank group were (24.6±5.3) %, (11.3±2.8) % and (7.6±3.8) % respectively. The expression of bone sialoprotein in experimental group were significantly higher than the other 2 groups( P= 0.000). Real-time quantitative PCR results showed that the expression level of Runt-related transcription factor 2 (RUNX2), type Ⅰcollagen (COL-Ⅰ), alkaline phosphatase in the experimental group was higher than in the blank group. The expression level of RUNX2 and COL-Ⅰ in the experimental group was higher than that of the control group ( P= 0.023). Conclusions: TGF-β3 has potential to promote the transformation of DPSC into osteoblasts, which can promote the integration of bone around the implant.

NASA LeRC's Acoustic Fill Effect Test Program and Results

NASA Technical Reports Server (NTRS)

Hughes, William O.; Mcnelis, Mark E.; Manning, Jerome E.

1994-01-01

NASA Lewis Research Center, in conjunction with General Dynamics Space Systems Division, has performed a test program to investigate the acoustic fill effect for an unblanketed payload fairing for a variety of payload simulators. This paper will discuss this test program and fill factor test data, and make comparisons with theoretical predictions. This paper will also address the NASA acoustic fill effect standard which was verified from the test data analysis.

Effect of filling factor on photonic bandgap of chalcogenide photonic crystal

NASA Astrophysics Data System (ADS)

Singh, Rajpal; Suthar, B.; Bhargava, A.

2018-05-01

In the present work, the photonic band structure of 1-D chalcogenide photonic crystal of As2S3/air multilayered structure is calculated using the plane wave expansion method. The study is extended to investigate the effect of filling factor on the photonic bandgap. The increase of bandgap is explained in the study.

General analysis of slab lasers using geometrical optics.

PubMed

Chung, Te-yuan; Bass, Michael

2007-02-01

A thorough and general geometrical optics analysis of a slab-shaped laser gain medium is presented. The length and thickness ratio is critical if one is to achieve the maximum utilization of absorbed pump power by the laser light in such a medium; e.g., the fill factor inside the slab is to be maximized. We point out that the conditions for a fill factor equal to 1, laser light entering and exiting parallel to the length of the slab, and Brewster angle incidence on the entrance and exit faces cannot all be satisfied at the same time. Deformed slabs are also studied. Deformation along the width direction of the largest surfaces is shown to significantly reduce the fill factor that is possible.

Simulation of electrowetting lens and prism arrays for wavefront compensation.

PubMed

Gopinath, Juliet T; Bright, Victor M; Cogswell, Carol C; Niederriter, Robert D; Watson, Alexander; Zahreddine, Ramzi; Cormack, Robert H

2012-09-20

A novel application of electrowetting devices has been simulated: wavefront correction using an array of electrowetting lenses and prisms. Five waves of distortion can be corrected with Strehl ratios of 0.9 or higher, utilizing piston, tip-tilt, and curvature corrections from arrays of 19 elements and fill factors as low as 40%. Effective control of piston can be achieved by placing the liquid lens array at the focus of two microlens arrays. Seven waves of piston delay can be generated with variation in focal length between 1.5 and 500 mm.

Investigation of the elastic modulus, tensile and flexural strength of five skull simulant materials for impact testing of a forensic skin/skull/brain model.

PubMed

Falland-Cheung, Lisa; Waddell, J Neil; Chun Li, Kai; Tong, Darryl; Brunton, Paul

2017-04-01

Conducting in vitro research for forensic, impact and injury simulation modelling generally involves the use of a skull simulant with mechanical properties similar to those found in the human skull. For this study epoxy resin, fibre filled epoxy resin, 3D-printing filaments (PETG, PLA) and self-cure acrylic denture base resin were used to fabricate the specimens (n=20 per material group), according to ISO 527-2 IBB and ISO20795-1. Tensile and flexural testing in a universal testing machine was used to measure their tensile/flexural elastic modulus and strength. The results showed that the epoxy resin and fibre filled epoxy resin had similar tensile elastic moduli (no statistical significant difference) with lower values observed for the other materials. The fibre filled epoxy resin had a considerably higher flexural elastic modulus and strength, possibly attributed to the presence of fibres. Of the simulants tested, epoxy resin had an elastic modulus and flexural strength close to that of mean human skull values reported in the literature, and thus can be considered as a suitable skull simulant for a skin/skull/brain model for lower impact forces that do not exceed the fracture stress. For higher impact forces a 3D printing filament (PLA) may be a more suitable skull simulant material, due to its closer match to fracture stresses found in human skull bone. Influencing factors were also anisotropy, heterogeneity and viscoelasticity of human skull bone and simulant specimens. Copyright © 2017 Elsevier Ltd. All rights reserved.

Factors associated with surface-level caries incidence in children aged 9 to 13: the Iowa Fluoride Study

PubMed Central

Broffitt, Barbara; Levy, Steven M.; Warren, John; Cavanaugh, Joseph E.

2017-01-01

Objective Since dental caries can progress throughout a person’s lifetime, understanding caries risk factors unique to specific life phases is important. This study aims to assess caries incidence and risk factors for young adolescents. Methods Participants in the longitudinal Iowa Fluoride Study were assessed for dental caries at approximately age 9 and again at age 13. These participants also filled out questionnaires concerning water sources, oral health habits, beverage intakes, parent education and family income. Caries progression (D2+F) was analyzed at the surface level. Mixed effects logistic regression was used to assess associations between surface-specific first molar occlusal caries incidence and risk factors. Results Caries incidence was quite low except on the first molar occlusal surfaces. In initial models of specific risk factors, incidence was positively associated with the surface having a D1 lesion at baseline, low family income, having untreated decay or fillings on other teeth at baseline, lower home water fluoride level, and higher soda pop consumption. In the final multiple variable model, significant interactions were found between tooth brushing frequency and initial D1 status, and also between family income and home tap water fluoride level. Conclusions D2+F incidence on first molar occlusal surfaces in these young adolescents was associated with prior caries experience on other teeth as well as prior evidence of a D1 lesion on the occlusal surface. More frequent tooth brushing was protective of sound surfaces, and fluoride in home tap water was also protective, but significantly more so for adolescents in low income families. PMID:23889610

The Tennessee study: factors affecting treatment outcome and healing time following nonsurgical root canal treatment.

PubMed

Azim, A A; Griggs, J A; Huang, G T-J

2016-01-01

To determine factors that may influence treatment outcome and healing time following root canal treatment. Root filled and restored teeth by pre-doctoral students were included in this study. Teeth/roots were followed-up regularly, and treatment outcome was evaluated at every follow-up appointment (healed, healing, uncertain or unsatisfactory). Host (age, immune condition, pulp/periapical diagnosis, tooth/root type, location and anatomy) and treatment factors (master apical file size, apical extension, voids and density of root filling) were recorded from patient dental records. Univariate, bivariate and multivariate analyses were performed to determine the impact of the factors on treatment outcomes and healing times. A total of 422 roots from 291 teeth met the inclusion criteria with a mean follow-up period of 2 years. The preoperative pulp condition, procedural errors during treatment, apical extension and density of root fillings significantly affected the treatment outcome. The average time required for a periapical lesion to heal was 11.78 months. The healing time increased in patients with compromised healing, patients older than 40 years, roots with Weine type II root canal systems, root canal systems prepared to a master apical file size <35, and roots with overextended fillings (P < 0.1). Multiple host and treatment factors affected the healing time and outcome of root canal treatment. Follow-up protocols should consider these factors before concluding the treatment outcome: patient's age, immune condition, as well as roots with overextended fillings, root canal systems with smaller apical preparations (size <35) or roots with complex canal systems. Intervention may be recommended if the treatment quality was inadequate or if patients became symptomatic. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Isotopomer fractionation during N2O consumption within soil mesocosms as a function of water filled pore space

NASA Astrophysics Data System (ADS)

Jinuntuya, M.; Ostrom, N. E.; Ostrom, P.; Sutka, R.

2005-12-01

Our prior research has demonstrated that the intramolecular distribution of 15N within the N2O molecule can be used to distinguish N2O derived from nitrification and denitrification. For this approach to be successful, however, the affect of fractionation during consumption of N2O by denitrification must be understood. Stable isotope and isotopomer analysis of soil mesocosm experiments were used to investigate fractionation of N2O during consumption at four different levels of water filled pores space (WFPS) 60, 80, 100 and 110% Uncultivated soil from the Long Term Ecological Research Site at Kellogg Biological Station was used to establish that the fractionation factors for δ15N, δ18O-N2O, δ15Nα and δ15Nβ ranged from -4.2 to -7.8 ‰, -12.5 to -19.1 ‰,-5.3 to -9.7‰ and -2.0 to -6.0 ‰, respectively. Lower fractionation factors were observed at higher WFPS demonstrating the importance of diffusion in limiting the expression of fractionation. The small degree of fractionation for δ15Nα and δ15Nβ indicates that consumption must be marked (e.g. >50%) before a significant isotope effect is observed. Our characterization of fractionation factors as a function of WFPS provides a basis to apportion the origins of N2O even when consumption is evident.

Transcriptome analysis of filling stage seeds among three buckwheat species with emphasis on rutin accumulation

PubMed Central

Wang, Tingting; Liu, Minxuan; Liu, Jing; Zhang, Zongwen

2017-01-01

Buckwheat is an important minor crop with pharmaceutical functions due to rutin enrichment in the seed. Seeds of common buckwheat cultivars (Fagopyrum esculentum, Fes) usually have much lower rutin content than tartary buckwheat (F. tartaricum, Ft). We previously found a wild species of common buckwheat (F. esculentum ssp. ancestrale, Fea), with seeds that are high in rutin, similar to Ft. In the present study, we investigated the mechanism by which rutin production varies among different buckwheat cultivars, Fea, a Ft variety (Xide) and a Fes variety (No.2 Pingqiao) using RNA sequencing of filling stage seeds. Sequencing data generated approximately 43.78-Gb of clean bases, all these data were pooled together and assembled 180,568 transcripts, and 109,952 unigenes. We established seed gene expression profiles of each buckwheat sample and assessed genes involved in flavonoid biosynthesis, storage proteins production, CYP450 family, starch and sucrose metabolism, and transcription factors. Differentially expressed genes between Fea and Fes were further analyzed due to their close relationship than with Ft. Expression levels of flavonoid biosynthesis gene FLS1 (Flavonol synthase 1) were similar in Fea and Ft, and much higher than in Fes, which was validated by qRT-PCR. This suggests that FLS1 transcript levels may be associated with rutin accumulation in filling stage seeds of buckwheat species. Further, we explored transcription factors by iTAK, and multiple gene families were identified as being involved in the coordinate regulation of metabolism and development. Our extensive transcriptomic data sets provide a complete description of metabolically related genes that are differentially expressed in filling stage buckwheat seeds and suggests that FLS1 is a key controller of rutin synthesis in buckwheat species. FLS1 can effectively convert dihydroflavonoids into flavonol products. These findings provide a basis for further studies of flavonoid biosynthesis in buckwheat breeding to help accelerate flavonoid metabolic engineering that would increase rutin content in cultivars of common buckwheat. PMID:29261741

An energy- and depth-dependent model for x-ray imaging

DOE Office of Scientific and Technical Information (OSTI.GOV)

Gallas, Brandon D.; Boswell, Jonathan S.; Badano, Aldo

In this paper, we model an x-ray imaging system, paying special attention to the energy- and depth-dependent characteristics of the inputs and interactions: x rays are polychromatic, interaction depth and conversion to optical photons is energy-dependent, optical scattering and the collection efficiency depend on the depth of interaction. The model we construct is a random function of the point process that begins with the distribution of x rays incident on the phosphor and ends with optical photons being detected by the active area of detector pixels to form an image. We show how the point-process representation can be used tomore » calculate the characteristic statistics of the model. We then simulate a Gd{sub 2}O{sub 2}S:Tb phosphor, estimate its characteristic statistics, and proceed with a signal-detection experiment to investigate the impact of the pixel fill factor on detecting spherical calcifications (the signal). The two extremes possible from this experiment are that SNR{sup 2} does not change with fill factor or changes in proportion to fill factor. In our results, the impact of fill factor is between these extremes, and depends on the diameter of the signal.« less

Experimental Study on Comprehensive Performance of Full Tailings Paste Filling in Jiaojia Gold Mine.

NASA Astrophysics Data System (ADS)

Zhang, Z. H.; Zou, Q. B.; Wang, P. Z.

2017-11-01

Filling mining method is the main method of modern underground mining. High concentration cementation is carried out using coarse tailing of +37 μm, and the mine has maturely used classified tailings paste filling technology. The gold mine studied on the performance of full tailings paste filling in order to maximize the use of tailings, reduce -37 μm fine tailings discharged into the tailing pond, reduce mining cost and eliminate security risks. The results show that: comprehensive index of full tailings paste filling is higher than that of classified tailings high concentration cementation filling, and the full tailings paste filling of 76% mass concentration has the best comprehensive index of slump, expansibility, yield stress and viscosity to meet the mining method requirements, which can effectively reduce the mining loss rate and dilution rate.

Risk of Prolonged Opioid Use Among Opioid-Naïve Patients Following Common Hand Surgery Procedures.

PubMed

Johnson, Shepard P; Chung, Kevin C; Zhong, Lin; Shauver, Melissa J; Engelsbe, Michael J; Brummett, Chad; Waljee, Jennifer F

2016-10-01

To evaluate prolonged opioid use in opioid-naïve patients after common hand surgery procedures in the United States. We studied insurance claims from the Truven MarketScan databases to identify opioid-naïve adult patients (no opioid exposure 11 months before the perioperative period) who underwent an elective (carpal tunnel release, carpometacarpal arthroplasty/arthrodesis, cubital tunnel release, or trigger finger release) or trauma-related (closed distal radius fracture fixation, flexor tendon repair, metacarpal fracture fixation, or phalangeal fracture fixation) hand surgery procedure between 2010 and 2012 (N = 77,573 patients). Patients were observed for 6 months to determine the number, timing, duration, and oral morphine equivalent dosage of postoperative opioid prescriptions. We assessed prolonged postoperative opioid use, defined as patients who filled a perioperative opioid prescription followed by a prescription between 90 and 180 days after surgery, and evaluated associated risk factors using multivariable logistic regression. In this cohort, 59,725 opioid-naïve patients (77%) filled a perioperative opioid prescription. Of these, 13% of patients continued to fill prescriptions between 90 and 180 days after surgery. Elective surgery patients were more likely to continue to fill opioid prescriptions after 90 days compared with trauma patients (13.5% vs 10.5%). Younger age, female gender, lower income, comprehensive insurance, higher Elixhauser comorbidity index, mental health disorders, and tobacco dependence or abuse were associated with prolonged opioid use. Approximately 13% of opioid-naïve patients continue to fill opioid prescriptions after hand surgery procedures 90 days after surgery. Preoperative interventions centered on opioid alternatives and early cessation, particularly among patients at risk for long-term use, is critical to addressing the prescription opioid crisis in the United States. The current national opioid use epidemic requires an assessment of the prevalence of hand surgery patients who receive and fill opioid prescriptions after common hand surgery procedures. Copyright © 2016 American Society for Surgery of the Hand. Published by Elsevier Inc. All rights reserved.

The dynamics of particle disks. III - Dense and spinning particle disks. [development of kinetic theory for planetary rings

NASA Technical Reports Server (NTRS)

Araki, Suguru

1991-01-01

The kinetic theory of planetary rings developed by Araki and Tremaine (1986) and Araki (1988) is extended and refined, with a focus on the implications of finite particle size: (1) nonlocal collisions and (2) finite filling factors. Consideration is given to the derivation of the equations for the local steady state, the low-optical-depth limit, and the steady state at finite filling factors (including the effects of collision inelasticity, spin degrees of freedom, and self-gravity). Numerical results are presented in extensive graphs and characterized in detail. The importance of distinguishing effects (1) and (2) at low optical depths is stressed, and the existence of vertical density profiles with layered structures at high filling factors is demonstrated.

Micro-CT and nano-CT analysis of filling quality of three different endodontic sealers.

PubMed

Huang, Yan; Celikten, Berkan; de Faria Vasconcelos, Karla; Ferreira Pinheiro Nicolielo, Laura; Lippiatt, Nicholas; Buyuksungur, Arda; Jacobs, Reinhilde; Orhan, Kaan

2017-12-01

To investigate voids in different root canal sealers using micro-CT and nano-CT, and to explore the feasibility of using nano-CT for quantitative analysis of sealer filling quality. 30 extracted mandibular central incisors were randomly assigned into three groups according to the applied root canal sealers (Total BC Sealer, Sure Seal Root, AH Plus) by the single cone technique. Subsequently, micro-CT and nano-CT were performed to analyse the incidence rate of voids, void fraction, void volume and their distribution in each sample. Micro-CT evaluation showed no significant difference among sealers for the incidence rate of voids or void fraction in the whole filling materials (p > 0.05), whereas a significant difference was found between AH Plus and the other two sealers using nano-CT (p < 0.05). All three sealers presented less void volume in the apical third; however, higher void volumes were observed in the apical and coronal thirds in AH Plus using micro-CT (p < 0.05), while nano-CT results displayed higher void volume in AH Plus among all the sealers and regions (p < 0.05). Bioactive sealers showed higher root filling rate, lower incidence rate of voids, void fraction and void volume than AH Plus under nano-CT analysis, when round root canals were treated by the single cone technique. The disparate results suggest that the higher resolution of nano-CT have a greater ability of distinguishing internal porosity, and therefore suggesting the potential use of nano-CT in quantitative analysis of filling quality of sealers.

Utilization of tooth filling services by people with disabilities in Taiwan.

PubMed

Chen, Ming-Chuan; Kung, Pei-Tseng; Su, Hsun-Pi; Yen, Suh-May; Chiu, Li-Ting; Tsai, Wen-Chen

2016-04-05

The oral condition of people with disabilities has considerable influence on their physical and mental health. However, nationwide surveys regarding this group have not been conducted. For this study, we used the National Health Insurance Research Database to explore the tooth filling utilization among people with disabilities. Using the database of the Ministry of the Interior in 2008 which included people with disabilities registered, we merged with the medical claims database in 2008 of the Bureau of National Health Insurance to calculate the tooth filling utilization and to analyze relative factors. We recruited 993,487 people with disabilities as the research sample. The tooth filling utilization was 17.53 %. The multiple logistic regression result showed that the utilization rate of men was lower than that of women (OR = 0.78, 95 % CI = 0.77-0.79) and older people had lower utilization rates (aged over 75, OR = 0.22, 95 % CI = 0.22-0.23) compared to those under the age of 20. Other factors that significantly influenced the low tooth filling utilization included a low education level, living in less urbanized areas, low economic capacity, dementia, and severe disability. We identified the factors that influence and decrease the tooth-filling service utilization rate: male sex, old age, low education level, being married, indigenous ethnicity, residing in a low urbanization area, low income, chronic circulatory system diseases, dementia, and severe disabilities. We suggest establishing proper medical care environments for high-risk groups to maintain their quality of life.

Effectiveness of rotary or manual techniques for removing a 6-year-old filling material.

PubMed

Duarte, Marco Antônio Hungaro; Só, Marcus Vinícius Reis; Cimadon, Vanessa Buffon; Zucatto, Cristiane; Vier-Pelisser, Fabiana Vieira; Kuga, Milton Carlos

2010-01-01

The aim of this study was to evaluate the effectiveness of manual and rotary instrumentation techniques for removing root fillings after different storage times. Twenty-four canals from palatal roots of human maxillary molars were instrumented and filled with gutta-percha and zinc-oxide eugenol-based sealer (Endofill) , and were stored in saline for 6 years. Non-aged control specimens were treated in the same manner and stored for 1 week. All canals were retreated using hand files or ProTaper Universal NiTi rotary system. Radiographs were taken to determine the amount of remaining material in the canals. The roots were vertically split, the halves were examined with a clinical microscope and the obtained images were digitized. The images were evaluated with AutoCAD software and the percentage of residual material was calculated. Data were analyzed with two-way ANOVA and Tukey's test at 5% significance level. There was no statistically significant differences (p>0.05) between the manual and rotary techniques for filling material removal regardless the ageing effect on endodontic sealers. When only the age of the filling material was analyzed microscopically, non-aged fillings that remained on the middle third of the canals presented a higher percentage of material remaining (p<0.05) compared to the aged sealers and to the other thirds of the roots. The apical third showed a higher percentage of residual filling material in both radiographic and microscopic analysis when compared to the other root thirds. In conclusion, all canals presented residual filling material after endodontic retreatment procedures. Microscopic analysis was more effective than radiographs for detection of residual filling material.

Use of landsat ETM+ SLC-off segment-based gap-filled imagery for crop type mapping

USGS Publications Warehouse

Maxwell, S.K.; Craig, M.E.

2008-01-01

Failure of the Scan Line Corrector (SLC) on the Landsat ETM+ sensor has had a major impact on many applications that rely on continuous medium resolution imagery to meet their objectives. The United States Department of Agriculture (USDA) Cropland Data Layer (CDL) program uses Landsat imagery as the primary source of data to produce crop-specific maps for 20 states in the USA. A new method has been developed to fill the image gaps resulting from the SLC failure to support the needs of Landsat users who require coincident spectral data, such as for crop type mapping and monitoring. We tested the new gap-filled method for a CDL crop type mapping project in eastern Nebraska. Scan line gaps were simulated on two Landsat 5 images (spring and late summer 2003) and then gap-filled using landscape boundary models, or segment models, that were derived from 1992 and 2002 Landsat images (used in the gap-fill process). Various date combinations of original and gap-filled images were used to derive crop maps using a supervised classification process. Overall kappa values were slightly higher for crop maps derived from SLC-off gap-filled images compared to crop maps derived from the original imagery (0.3–1.3% higher). Although the age of the segment model used to derive the SLC-off gap-filled product did not negatively impact the overall agreement, differences in individual cover type agreement did increase (−0.8%–1.6% using the 2002 segment model to −5.0–5.1% using the 1992 segment model). Classification agreement also decreased for most of the classes as the size of the segment used in the gap-fill process increased.

Maternal self-report of oral health in six-year-old Pacific children from South Auckland, New Zealand.

PubMed

Paterson, Janis E; Gao, Wanzhen; Sundborn, Gerhard; Cartwright, Susan

2011-02-01

To examine maternal and socio-demographic factors associated with oral health practices and experiences in six-year-old Pacific children. The longitudinal Pacific Islands Families (PIF) study is following a cohort of Pacific children born in Auckland, New Zealand in 2000. At approximately six years postpartum maternal reports (n = 1001) on child oral health practices and experiences of fillings and extractions were gathered. Forty-five per cent of mothers reported that their child had experienced fillings or extractions. After adjusting for confounding factors, we found that Tongan children were almost twice as likely to have their teeth filled or extracted than Samoan children (OR, 1.93; 95%, 1.34-2.77). Differences between Samoan children and children of other ethnic groups were not significant. Children of mothers who had secondary qualifications were significantly less likely to have their teeth filled or extracted compared to children of mothers who had postsecondary qualifications (OR, 0.634; 95%, 0.44-0.90). Prolonged duration of breastfeeding was associated with an increased likelihood of filling or extraction experience. In terms of maternal oral hygiene, maternal tooth brushing frequency of less that once a day was significantly associated with increased odds of fillings and/or extractions in their children (OR, 1.35; 95% CI, 1.02-1.79). Children who were sometimes supervised for tooth brushing were significantly more likely to have fillings or extractions than children who were not provided supervision. These findings highlight the role of cultural factors and maternal hygiene in child oral health outcomes and suggest that health promotion efforts should encompass the whole family and embrace a culturally appropriate approach. © 2010 John Wiley & Sons A/S.

Employing Lead Thiocyanate Additive to Reduce the Hysteresis and Boost the Fill Factor of Planar Perovskite Solar Cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ke, Weijun; Xiao, Chuanxiao; Wang, Changlei

2016-05-04

Lead thiocyanate in the perovskite precursor can increase the grain size of a perovskite thin film and reduce the conductivity of the grain boundaries, leading to perovskite solar cells with reduced hysteresis and enhanced fill factor. A planar perovskite solar cell with grain boundary and interface passivation achieves a steady-state efficiency of 18.42%.

Cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber compounds in the presence of alkanolamide

NASA Astrophysics Data System (ADS)

Surya, I.; Hayeemasae, N.; Ginting, M.

2018-03-01

The effects of alkanolamide (ALK) addition on cure characteristics, crosslink density and degree of filler dispersion of kaolin-filled natural rubber (NR) compounds were investigated. The kaolin filler was incorporated into NR compounds with a fixed loading, 30.0 phr. The ALK was prepared from Refined Bleached Deodorized Palm Stearin (RBDPS), a waste product of cooking oil production, and diethanolamine. The ALK is an oily material and added into the filled NR compounds as a rubber additive at different loadings, 0.0, 3.0, 5.0 and 7.0. The kaolin-filled NR compounds with and without ALK were vulcanized using a semi-efficient vulcanization system. It was found that ALK decreased the scorch and cure times and improved filler dispersion of the kaolin-filled NR compounds. The higher the ALK loading, the shorter were the scorch and cure times. It was also found that ALK increased the crosslink density of kaolin-filled NR compound up to 5.0 phr of loading. Due to its oily properties, The ALK acted as an internal plasticizer which decreased the minimum torque and improved the degree of kaolin dispersion in NR phases. The higher the ALK loading; the lower the minimum torque and better the filler dispersion.

Identifying and overcoming the effect of mass transfer limitation on decreased yield in enzymatic hydrolysis of lignocellulose at high solid concentrations.

PubMed

Du, Jian; Cao, Yuan; Liu, Guodong; Zhao, Jian; Li, Xuezhi; Qu, Yinbo

2017-04-01

Cellulose conversion decreases significantly with increasing solid concentrations during enzymatic hydrolysis of insoluble lignocellulosic materials. Here, mass transfer limitation was identified as a significant determining factor of this decrease by studying the hydrolysis of delignified corncob residue in shake flask, the most used reaction vessel in bench scale. Two mass transfer efficiency-related factors, mixing speed and flask filling, were shown to correlate closely with cellulose conversion at solid loadings higher than 15% DM. The role of substrate characteristics in mass transfer performance was also significant, which was revealed by the saccharification of two corn stover substrates with different pretreatment methods at the same solid loading. Several approaches including premix, fed-batch operation, and particularly the use of horizontal rotating reactor were shown to be valid in facilitating cellulose conversion via improving mass transfer efficiency at solid concentrations higher than 15% DM. Copyright © 2017 Elsevier Ltd. All rights reserved.

Payment systems and oral health in Swedish dental care: Observations over six years.

PubMed

Andås, C A; Hakeberg, M

2016-12-01

The aim of this longitudinal study of patients in regular dental care was to compare the findings of manifest caries and fillings after a 6-year adherence to either of two optional payment models, the traditional fee-for service (FFS) model, or the new capitation model 'Dental Care for Health' (DCH). Data on manifest caries lesions, the number of fillings and a number of background variables were collected from both a register and a questionnaire completed by 6,299 regular dental patients who met the inclusion criteria. The influence of payment system adherence and background variables on the number of manifest caries lesions at study end was examined by the means of negative binomial regression analysis. The incidence rate ratio of manifest caries lesions after six years in FFS was 1.5 compared to DCH, after controlling for age, gender, education and pre-baseline caries incidence. The number of fillings was higher in FFS than in DCH at study start and at study end, and was also described by a steeper slope. At group level, this study showed a statistically significant difference between the caries situation after six years in DCH compared with FFS, when some important background factors, including pre-baseline caries, were kept constant in a regression model. Copyright© 2016 Dennis Barber Ltd

Incorporating simvastatin/poloxamer 407 hydrogel into 3D-printed porous Ti6Al4V scaffolds for the promotion of angiogenesis, osseointegration and bone ingrowth.

PubMed

Liu, Hao; Li, Wei; Liu, Can; Tan, Jie; Wang, Hong; Hai, Bao; Cai, Hong; Leng, Hui-Jie; Liu, Zhong-Jun; Song, Chun-Li

2016-10-27

Three-dimensional porous titanium alloys printed via electron beam melting have low stiffness similar to that of cortical bone and are promising scaffolds for orthopedic applications. However, the bio-inert nature of titanium alloy is poorly compatible with bone ingrowth. We previously observed that simvastatin/poloxamer 407 thermosensitive hydrogel induces endogenous angiogenic/osteogenic growth factors and promotes angiogenesis and osteogenesis, but the mechanical properties of this hydrogel are poor. The purpose of this study was to construct 3D-printed porous titanium scaffolds (pTi scaffolds) filled with simvastatin/hydrogel and evaluate the effects of this composite on osseointegration, bone ingrowth and neovascularization using a tibial defect rabbit model. Four and eight weeks after implantation, the bone volume, bone mineral density, mineral apposition rate, and push-in maximum force of the pTi scaffolds filled with simvastatin/hydrogel were significantly higher than those without simvastatin (p < 0.05). Moreover, filling with simvastatin/hydrogel significantly enhanced vascularization in and around the pTi scaffolds, and a significant correlation was observed between the volume of new bone and neovascularization (p < 0.01). In conclusion, incorporating simvastatin/poloxamer 407 hydrogel into pTi scaffolds significantly improves neovascularization, osseointegration and bone ingrowth.

Radiographic and Histological Evaluation of the Healing of Extraction Sockets Filled With Bovine-Derived Xenograft: An Experimental Study in Rats.

PubMed

Zhou, Fengjuan; Zheng, Xiaofei; Xie, Meng; Mo, Anchun; Wu, Hongkun

2017-06-01

To evaluate the microenvironment changes in the sockets substituted with bovine-derived xenografts during the early healing period. After extraction of the right maxillary incisor of Sprague Dawley rats, 48 rats were randomly divided into 2 groups. The extraction sockets of the test group were filled with Bio-Oss, whereas the control group was allowed to heal without intervention. The bone quality of the extraction sockets was observed through micro-CT and immunohistochemistry. Micro-CT scanning showed that the bone mineral density in the test group was significantly higher than that in the control group during the early healing period, whereas immunohistochemistry showed that the bone formation-related factors were significantly different between the test and control groups. The bovine-derived xenografts may interfere with the healing process of the extraction socket in the early healing stage. Bone formation of the extraction socket was delayed after grafting with bone substitute.

Liquid core microbubble resonators for highly sensitive temperature sensing

NASA Astrophysics Data System (ADS)

Ward, Jonathan M.; Yang, Yong; Nic Chormaic, Sile

2014-03-01

It is experimentally shown that a large thermal blue shift of up to 100 GHz/K (0.2 nm/K at a wavelength of 775 nm) can be achieved with higher order radial modes in an ethanol-filled microbubble whispering gallery mode resonator (WGR). Q-factors for the most thermally sensitive modes are typically 105, equivalent to a measurement resolution of 8.5 mK. The thermal shift rate is determined for different modes when the core of the microbubble is filled with air, water, and ethanol. The measured shifts are compared against Finite Element Model (FEM) simulations. It is also shown that, if the microbubble is in the quasi-droplet regime, the fundamental TE mode in a bubble with a 500 nm wall is estimated to experience a shift of 35 GHz/K, while the effective index is still high enough to allow efficient coupling to a tapered optical fiber. Nonetheless, at a wall thickness of 1 μm, the most sensitive modes (n = 2) observed were still strongly coupled.

Parameter analysis on the ultrasonic TSV-filling process and electrochemical characters

NASA Astrophysics Data System (ADS)

Wang, Fuliang; Ren, Xinyu; Wang, Yan; Zeng, Peng; Zhou, Zhaohua; Xiao, Hongbin; Zhu, Wenhui

2017-10-01

As one of the key technologies in 3D packaging, through silicon via (TSV) interconnection technology has become a focus recently. In this paper, an electrodeposition method for TSV filling with the assistance of ultrasound and additives are introduced. Two important parameters i.e. current density and ultrasonic power are studied for TSV filling process and electrochemical properties. It is found that ultrasound can improve the quality of TSV-filling and change the TSV-filling mode. The experimental results also indicate that the filling rate enhances more significantly with decreasing current density under ultrasonic conditions than under silent conditions. In addition, according to the voltammetry curve, the increase of ultrasonic power can significantly increase the current density of cupric reduction, and decrease the thickness of diffusion layer. So that the reduction speed of copper ions is accelerated, resulting in a higher TSV-filling rate.

High-resolution observations of the polar magnetic fields of the sun

NASA Technical Reports Server (NTRS)

Lin, H.; Varsik, J.; Zirin, H.

1994-01-01

High-resolution magnetograms of the solar polar region were used for the study of the polar magnetic field. In contrast to low-resolution magnetograph observations which measure the polar magnetic field averaged over a large area, we focused our efforts on the properties of the small magnetic elements in the polar region. Evolution of the filling factor (the ratio of the area occupied by the magnetic elements to the total area) of these magnetic elements, as well as the average magnetic field strength, were studied during the maximum and declining phase of solar cycle 22, from early 1991 to mid-1993. We found that during the sunspot maximum period, the polar regions were occupied by about equal numbers of positive and negative magnetic elements, with equal average field strength. As the solar cycle progresses toward sunspot minimum, the magnetic field elements in the polar region become predominantly of one polarity. The average magnetic field of the dominant polarity elements also increases with the filling factor. In the meanwhile, both the filling factor and the average field strength of the non-dominant polarity elements decrease. The combined effects of the changing filling factors and average field strength produce the observed evolution of the integrated polar flux over the solar cycle. We compared the evolutionary histories of both filling factor and average field strength, for regions of high (70-80 deg) and low (60-70 deg) latitudes. For the south pole, we found no significant evidence of difference in the time of reversal. However, the low-latitude region of the north pole did reverse polarity much earlier than the high-latitude region. It later showed an oscillatory behavior. We suggest this may be caused by the poleward migration of flux from a large active region in 1989 with highly imbalanced flux.

Temperament traits and psychopathy in a group of patients with antisocial personality disorder.

PubMed

Basoglu, Cengiz; Oner, Ozgur; Ates, Alpay; Algul, Ayhan; Bez, Yasin; Ebrinc, Servet; Cetin, Mesut

2011-01-01

The Psychopathy Checklist Revised (PCL-R) and Temperament and Character Inventory (TCI) have been used extensively in research of personality disorders; however, no previous study has investigated the relation between psychopathy factors and temperament and character traits in patients with antisocial personality disorder (ASPD). Our aim was to fill this gap in the literature. The PCL-R Factor scores and the TCI temperament and character scores were evaluated in 68 men with ASPD and 65 healthy male controls. The ASPD cases had significantly higher PCL-R Factor 1, Factor 2, and Total scores, as well as significantly higher TCI Novelty Seeking and Harm Avoidance scores, whereas the control group had higher TCI Reward Dependence, Persistence, Self-Directedness, and Cooperativeness scores. Correlation analysis revealed that, in the whole study group, PCL-R Factor 1, Factor 2, and Total scores were positively correlated with Novelty Seeking and Harm Avoidance scores and negatively correlated with Reward Dependence, Persistence, Self-Directedness, and Cooperativeness scores. When each group was analyzed separately, the correlations were not significant. Regression analysis supported the main findings. Our results showed that both PCL-R Factor 1 score, which is claimed to reflect "core psychopathy," and PCL-R Factor 2 score, which reflects criminal behaviors, were positively correlated with Novelty Seeking and Harm Avoidance and were negatively correlated with Reward Dependence in the whole sample. The reduced variance of PCL-R in each group might lead to nonsignificant associations within groups. Without the subjects with severe psychopathy in the present study, it might not be possible to show the association. Copyright © 2011 Elsevier Inc. All rights reserved.

Effects of selective attention on perceptual filling-in.

PubMed

De Weerd, P; Smith, E; Greenberg, P

2006-03-01

After few seconds, a figure steadily presented in peripheral vision becomes perceptually filled-in by its background, as if it "disappeared". We report that directing attention to the color, shape, or location of a figure increased the probability of perceiving filling-in compared to unattended figures, without modifying the time required for filling-in. This effect could be augmented by boosting attention. Furthermore, the frequency distribution of filling-in response times for attended figures could be predicted by multiplying the frequencies of response times for unattended figures with a constant. We propose that, after failure of figure-ground segregation, the neural interpolation processes that produce perceptual filling-in are enhanced in attended figure regions. As filling-in processes are involved in surface perception, the present study demonstrates that even very early visual processes are subject to modulation by cognitive factors.

Improvement of 2D ERT measurements conducted along a small earth-filled dyke using 3D topographic data and 3D computation of geometric factors

NASA Astrophysics Data System (ADS)

Bièvre, Grégory; Oxarango, Laurent; Günther, Thomas; Goutaland, David; Massardi, Michael

2018-06-01

In the framework of earth-filled dykes characterization and monitoring, Electrical Resistivity Tomography (ERT) turns out to be a commonly used method. 2D sections are generally acquired along the dyke crest thus putting forward the question of 3D artefacts in the inversion process. This paper proposes a methodology based on 3D direct numerical simulations of the ERT acquisition using a realistic topography of the study site. It allows computing ad hoc geometrical factors which can be used for the inversion of experimental ERT data. The method is first evaluated on a set of synthetic dyke configurations. Then, it is applied to experimental static and time-lapse ERT data set acquired before and after repair works carried out on a leaking zone of an earth-filled canal dyke in the centre of France. The computed geometric factors are lower than the analytic geometric factors in a range between -8% and - 18% for measurements conducted on the crest of the dyke. They exhibit a maximum under-estimation for intermediate electrode spacings in the Wenner and Schlumberger configurations. In the same way, for measurements conducted on the mid-slope of the dyke, the computed geometric factors are higher for short electrode spacings (+18%) and lower for lower for large electrode spacings (-8%). The 2D inversion of the synthetic data with these computed geometric factors provides a significant improvement of the agreement with the original resistivity. Two experimental profiles conducted on the same portion of the dyke but at different elevations also reveal a better agreement using this methodology. The comparison with apparent resistivity from EM31 profiling along the stretch of the dyke also supports this evidence. In the same way, some spurious effects which affected the time-lapse data were removed and improved the global readability of the time-lapse resistivity sections. The benefit on the structural interpretation of ERT images remains moderate but allows a better delineation of the repair work location. Therefore, and even if the 2D assumption cannot be considered valid in such a context, the proposed methodology could be applied easily to any dyke or strongly 3D-shaped structure using a realistic topographic model. It appears suitable for practical application.

Perovskite solar cell with an efficient TiO₂ compact film.

PubMed

Ke, Weijun; Fang, Guojia; Wang, Jing; Qin, Pingli; Tao, Hong; Lei, Hongwei; Liu, Qin; Dai, Xin; Zhao, Xingzhong

2014-09-24

A perovskite solar cell with a thin TiO2 compact film prepared by thermal oxidation of sputtered Ti film achieved a high efficiency of 15.07%. The thin TiO2 film prepared by thermal oxidation is very dense and inhibits the recombination process at the interface. The optimum thickness of the TiO2 compact film prepared by thermal oxidation is thinner than that prepared by spin-coating method. Also, the TiO2 compact film and the TiO2 porous film can be sintered at the same time. This one-step sintering process leads to a lower dark current density, a lower series resistance, and a higher recombination resistance than those of two-step sintering. Therefore, the perovskite solar cell with the TiO2 compact film prepared by thermal oxidation has a higher short-circuit current density and a higher fill factor.

High altitude current-voltage measurement of GaAs/Ge solar cells

NASA Astrophysics Data System (ADS)

Hart, Russell E., Jr.; Brinker, David J.; Emery, Keith A.

Measurements of high-voltage (Voc of 1.2 V) gallium arsenide on germanium tandem junction solar cells at air mass 0.22 showed that the insolation in the red portion of the solar spectrum is insufficient to obtain high fill factor. On the basis of measurements in the LeRC X-25L solar simulator, these cells were believed to be as efficient as 21.68 percent AM0. Solar simulator spectrum errors in the red end allowed the fill factor to be as high as 78.7 percent. When a similar cell's current-voltage characteristic was measured at high altitude in the NASA Lear Jet Facility, a loss of 15 percentage points in fill factor was observed. This decrease was caused by insufficient current in the germanium bottom cell of the tandem stack.

Conceptual understanding and groundwater quality of selected basin-fill aquifers in the Southwestern United States

USGS Publications Warehouse

Thiros, Susan A.; Bexfield, Laura M.; Anning, David W.; Huntington, Jena M.

2010-01-01

The National Water-Quality Assessment (NAWQA) Program of the U.S. Geological Survey has been conducting a regional analysis of water quality in the principal aquifer systems in the southwestern United States (hereinafter, “Southwest”) since 2005. Part of the NAWQA Program, the objective of the Southwest Principal Aquifers (SWPA) study is to develop a better understanding of water quality in basin-fill aquifers in the region by synthesizing information from case studies of 15 basins into a common set of important natural and human-related factors found to affect groundwater quality.The synthesis consists of three major components:1. Summary of current knowledge about the groundwater systems, and the status of, changes in, and influential factors affecting quality of groundwater in basin-fill aquifers in 15 basins previously studied by NAWQA (this report).2. Development of a conceptual model of the primary natural and human-related factors commonly affecting groundwater quality, thereby building a regional understanding of the susceptibility and vulnerability of basin-fill aquifers to contaminants.3. Development of statistical models that relate the concentration or occurrence of specific chemical constituents in groundwater to natural and human-related factors linked to the susceptibility and vulnerability of basin-fill aquifers to contamination.Basin-fill aquifers occur in about 200,000 mi2 of the 410,000 mi2 SWPA study area and are the primary source of groundwater supply for cities and agricultural communities. Four of the principal aquifers or aquifer systems of the United States are included in the basin-fill aquifers of the study area: (1) the Basin and Range basin-fill aquifers in California, Nevada, Utah, and Arizona; (2) the Rio Grande aquifer system in New Mexico and Colorado; (3) the California Coastal Basin aquifers; and (4) the Central Valley aquifer system in California. Because of the generally limited availability of surface-water supplies in the arid to semiarid climate, cultural and economic activities in the Southwest are particularly dependent on supplies of good-quality groundwater. Irrigation and public-supply withdrawals from basin-fill aquifers in the study area account for about one quarter of the total withdrawals from all aquifers in the United States.Many factors influence the quality of groundwater in the 15 case-study basins, but some common factors emerge from the basin summaries presented in this report. These factors include the chemical composition of the recharge water, consolidated rock geology and composition of aquifer materials derived from consolidated rock, and land and water use. The major water-quality issues in many of the developed case-study basins are increased concentrations of dissolved solids, nitrate, and VOCs in groundwater as a result of human activities.The information presented and the citations listed in this report serve as a resource for those interested in the groundwater-flow systems in the NAWQA case-study basins. The summaries of water-development history, hydrogeology, conceptual understanding of the groundwater system under both predevelopment and modern conditions, and effects of natural and human-related factors on groundwater quality presented in the sections on each basin also serve as a foundation for the synthesis and modeling phases of the SWPA regional study.

Using remote sensing data to predict road fill areas and areas affected by fill erosion with planned forest road construction: a case study in Kastamonu Regional Forest Directorate (Turkey).

PubMed

Aricak, Burak

2015-07-01

Forest roads are essential for transport in managed forests, yet road construction causes environmental disturbance, both in the surface area the road covers and in erosion and downslope deposition of road fill material. The factors affecting the deposition distance of eroded road fill are the slope gradient and the density of plant cover. Thus, it is important to take these factors into consideration during road planning to minimize their disturbance. The aim of this study was to use remote sensing and field surveying to predict the locations that would be affected by downslope deposition of eroding road fill and to compile the data into a geographic information system (GIS) database. The construction of 99,500 m of forest roads is proposed for the Kastamonu Regional Forest Directorate in Turkey. Using GeoEye satellite images and a digital elevation model (DEM) for the region, the location and extent of downslope deposition of road fill were determined for the roads as planned. It was found that if the proposed roads were constructed by excavators, the fill material would cover 910,621 m(2) and the affected surface area would be 1,302,740 m(2). Application of the method used here can minimize the adverse effects of forest roads.

The tunable mechanical property of water-filled carbon nanotubes under an electric field

NASA Astrophysics Data System (ADS)

Ye, Hongfei; Zhang, Zhongqiang; Zhang, Hongwu; Chen, Zhen; Zong, Zhi; Zheng, Yonggang

2014-03-01

The spring-induced compression of water-filled carbon nanotubes (CNTs) under an electric field is investigated by molecular dynamics simulations. Due to the incompressibility and polarity of water, the mechanical property of CNTs can be tuned through filling with water molecules and applying an electric field. To explore the variation of the mechanical property of water-filled CNTs, the effects of the CNT length, the filling density and the electric field intensity are examined. The simulation results indicate that the water filling and electric field can result in a slight change in the elastic property (the elastic modulus and Poisson's ratio) of water-filled CNTs. However, the yield stress and average post-buckling stress exhibit a significant response to the water density and electric field intensity. As compared to hollow CNTs, the increment in yield stress of the water-filled CNTs under an electric field of 2.0 V Å-1 is up to 35.29%, which is even higher than that resulting from metal filling. The findings from this study provide a valuable theoretical basis for designing and fabricating the controlling units at the nanoscale.

Landslide Distribution, Damage and Land Use Interactions During the 2004 Chuetsu Earthquake

NASA Astrophysics Data System (ADS)

Sidle, R. C.; Trandafir, A. C.; Kamai, T.

2005-05-01

A series of earthquakes struck Niigata Prefecture, Japan, on 23 October 2004 killing about 40 people and injuring about 3000. These earthquakes were characterized by a shallow focal depth (13 km) that generated strong levels of ground motion, resulting in extensive damage and thousands of landslides throughout the region. Most landslides on natural slopes occurred in the regional geological structure consisting of sandy siltstone and thin-bedded alternations of sandstone and siltstone. Earthquakes exacerbate such potential instabilities by the ground motion induced and the enhancement of pore water pressure in wet regoliths. The three strongest earthquakes occurred within a period of less than 40 minutes, and had sequential magnitudes (JMA) of 6.8, 6.3, and 6.5. The highest density of landslides (12/km2) was mapped within a 2.9 km radius of the M6.5 epicenter near Yamakoshi village; about 4 times higher density compared to the other epicenters located to the east and west. This higher density may be a consequence of the cumulative shaking effects associated with the two earlier earthquakes of M6.8 and 6.5, in addition to the topographic and geologic factors controlling the stability of the region. Roads, residential fills, agricultural terraces on hillslopes, and other earthworks increased the susceptibility of sites to slope failure. Numerous earthquake-induced failures in terraces and adjacent hillslopes around rice paddy fields occurred near Yamakoshi village. A housing development in Nagaoka city constructed on an old earthflow suffered from severe damage to fill slopes during the earthquake. Nearly saturated conditions in these deep fills together with poor drainage systems contributed to the landslide damages. Clearly, land use activities in rural and urban areas exacerbated the extent of earthquake-triggered landslides.

Stability of selected volatile breath constituents in Tedlar, Kynar and Flexfilm sampling bags

PubMed Central

Mochalski, Paweł; King, Julian; Unterkofler, Karl; Amann, Anton

2016-01-01

The stability of 41 selected breath constituents in three types of polymer sampling bags, Tedlar, Kynar, and Flexfilm, was investigated using solid phase microextraction and gas chromatography mass spectrometry. The tested molecular species belong to different chemical classes (hydrocarbons, ketones, aldehydes, aromatics, sulphurs, esters, terpenes, etc.) and exhibit close-to-breath low ppb levels (3–12 ppb) with the exception of isoprene, acetone and acetonitrile (106 ppb, 760 ppb, 42 ppb respectively). Stability tests comprised the background emission of contaminants, recovery from dry samples, recovery from humid samples (RH 80% at 37 °C), influence of the bag’s filling degree, and reusability. Findings yield evidence of the superiority of Tedlar bags over remaining polymers in terms of background emission, species stability (up to 7 days for dry samples), and reusability. Recoveries of species under study suffered from the presence of high amounts of water (losses up to 10%). However, only heavier volatiles, with molecular masses higher than 90, exhibited more pronounced losses (20–40%). The sample size (the degree of bag filling) was found to be one of the most important factors affecting the sample integrity. To sum up, it is recommended to store breath samples in pre-conditioned Tedlar bags up to 6 hours at the maximum possible filling volume. Among the remaining films, Kynar can be considered as an alternative to Tedlar; however, higher losses of compounds should be expected even within the first hours of storage. Due to the high background emission Flexfilm is not suitable for sampling and storage of samples for analyses aiming at volatiles at a low ppb level. PMID:23323261

Analyses of mode filling factor of a laser end-pumped by a LD with high-order transverse modes

NASA Astrophysics Data System (ADS)

Han, Juhong; Wang, You; An, Guofei; Rong, Kepeng; Yu, Hang; Wang, Shunyan; Zhang, Wei; Cai, He; Xue, Liangping; Wang, Hongyuan; Zhou, Jie

2017-05-01

Although the concept of the mode filling factor (also named as "mode-matching efficiency") has been well discussed decades before, the concept of so-called overlap coefficient is often confused by the laser technicians because there are several different formulae for various engineering purposes. Furthermore, the LD-pumped configurations have become the mainstream of solid-state lasers since their compact size, high optical-to-optical efficiency, low heat generation, etc. As the beam quality of LDs are usually very unsatisfactory, it is necessary to investigate how the mode filling factor of a laser system is affected by a high-powered LD pump source. In this paper, theoretical analyses of an end-pumped laser are carried out based on the normalized overlap coefficient formalism. The study provides a convenient tool to describe the intrinsically complex issue of mode interaction corresponding to a laser and an end-pumped source. The mode filling factor has been studied for many cases in which the pump mode and the laser mode have been considered together in the calculation based on analyses of the rate equations. The results should be applied for analyses of any other types of lasers with the similar optical geometry.

The effect of split pixel HDR image sensor technology on MTF measurements

NASA Astrophysics Data System (ADS)

Deegan, Brian M.

2014-03-01

Split-pixel HDR sensor technology is particularly advantageous in automotive applications, because the images are captured simultaneously rather than sequentially, thereby reducing motion blur. However, split pixel technology introduces artifacts in MTF measurement. To achieve a HDR image, raw images are captured from both large and small sub-pixels, and combined to make the HDR output. In some cases, a large sub-pixel is used for long exposure captures, and a small sub-pixel for short exposures, to extend the dynamic range. The relative size of the photosensitive area of the pixel (fill factor) plays a very significant role in the output MTF measurement. Given an identical scene, the MTF will be significantly different, depending on whether you use the large or small sub-pixels i.e. a smaller fill factor (e.g. in the short exposure sub-pixel) will result in higher MTF scores, but significantly greater aliasing. Simulations of split-pixel sensors revealed that, when raw images from both sub-pixels are combined, there is a significant difference in rising edge (i.e. black-to-white transition) and falling edge (white-to-black) reproduction. Experimental results showed a difference of ~50% in measured MTF50 between the falling and rising edges of a slanted edge test chart.

Buried MoO x/Ag Electrode Enables High-Efficiency Organic/Silicon Heterojunction Solar Cells with a High Fill Factor.

PubMed

Xia, Zhouhui; Gao, Peng; Sun, Teng; Wu, Haihua; Tan, Yeshu; Song, Tao; Lee, Shuit-Tong; Sun, Baoquan

2018-04-25

Silicon (Si)/organic heterojunction solar cells based on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) and n-type Si have attracted wide interests because they promise cost-effectiveness and high-efficiency. However, the limited conductivity of PEDOT:PSS leads to an inefficient hole transport efficiency for the heterojunction device. Therefore, a high dense top-contact metal grid electrode is required to assure the efficient charge collection efficiency. Unfortunately, the large metal grid coverage ratio electrode would lead to undesirable optical loss. Here, we develop a strategy to balance PEDOT:PSS conductivity and grid optical transmittance via a buried molybdenum oxide/silver grid electrode. In addition, the grid electrode coverage ratio is optimized to reduce its light shading effect. The buried electrode dramatically reduces the device series resistance, which leads to a higher fill factor (FF). With the optimized buried electrode, a record FF of 80% is achieved for flat Si/PEDOT:PSS heterojunction devices. With further enhancement adhesion between the PEDOT:PSS film and Si substrate by a chemical cross-linkable silance, a power conversion efficiency of 16.3% for organic/textured Si heterojunction devices is achieved. Our results provide a path to overcome the inferior organic semiconductor property to enhance the organic/Si heterojunction solar cell.

Tablet, web-based, or paper questionnaires for measuring anxiety in patients suspected of breast cancer: patients' preferences and quality of collected data.

PubMed

Barentsz, Maarten W; Wessels, Hester; van Diest, Paul J; Pijnappel, Ruud M; Haaring, Cees; van der Pol, Carmen C; Witkamp, Arjen J; van den Bosch, Maurice A; Verkooijen, Helena M

2014-10-31

Electronic applications are increasingly being used in hospitals for numerous purposes. Our aim was to assess differences in the characteristics of patients who choose paper versus electronic questionnaires and to evaluate the data quality of both approaches. Between October 2012 and June 2013, 136 patients participated in a study on diagnosis-induced stress and anxiety. Patients were asked to fill out questionnaires at six different moments during the diagnostic phase. They were given the opportunity to fill out the questionnaires on paper or electronically (a combination of tablet and Web-based questionnaires). Demographic characteristics and completeness of returned data were compared between groups. Nearly two-thirds of patients (88/136, 64.7%) chose to fill out the questionnaires on paper, and just over a third (48/136, 35.3%) preferred the electronic option. Patients choosing electronic questionnaires were significantly younger (mean 47.3 years vs mean 53.5 in the paper group, P=.01) and higher educated (P=.004). There was significantly more missing information (ie, at least one question not answered) in the paper group during the diagnostic day compared to the electronic group (using a tablet) (28/88 vs 1/48, P<.001). However, in the week after the diagnostic day, missing information was significantly higher in the electronic group (Web-based questionnaires) compared to the paper group (41/48 vs 38/88, P<.001). Younger patients and patients with a higher level of education have a preference towards filling out questionnaires electronically. In the hospital, a tablet is an excellent medium for patients to fill out questionnaires with very little missing information. However, for filling out questionnaires at home, paper questionnaires resulted in a better response than Web-based questionnaires.

Examining the factors that are correlated with mindfulness with a focus on attention deficit hyperactivity symptoms.

PubMed

Yavuz, Burcu Goksan; Yavuz, Mesut; Onal, Arzu

2018-05-18

We hypothesized that attention deficit hyperactivity symptoms would negatively correlate with the level of mindfulness. Seventy-six subjects referred to the outpatient psychiatry unit and 32 healthy control subjects filled out the Mindful Attention Awareness Scale (MAAS), the Depression Anxiety Stress Scale (DASS), the Adult ADHD Self-Report Scale (ASRS), and the Wender Utah Rating Scale (WURS). Patients scored higher on ADH symptoms compared to controls (p ≤ .001). Higher scores on the ASRS and WURS revealed lower mindfulness in the study group (p ≤ .001). WURS, DASS depression, ASRS attention subscale-based scores (p < .05) were significant predictors on MAAS scores. Besides emotional symptoms ADH symptoms had a significant predictive value on mindfulness. © 2018 Wiley Periodicals, Inc.

Changes in the perceived neighborhood environment in relation to changes in physical activity: A longitudinal study from childhood into adolescence.

PubMed

D'Haese, Sara; De Meester, Femke; Cardon, Greet; De Bourdeaudhuij, Ilse; Deforche, Benedicte; Van Dyck, Delfien

2015-05-01

The aim was to investigate how physical activity and the perceived neighborhood environment in children change when they enter adolescence. Also the relation between changes in the perceived environment and changes in children's physical activity was investigated. In total, 321 children and one of their parents filled out a physical activity questionnaire and the NEWS-Y at two time points (last grade of elementary school and 2 years later). Children also wore an activity monitor. Changes in children's physical activity were dependent on the physical activity domain. Only less than half of children's perceived neighborhood factors changed and about half of the parental perceived neighborhood factors changed. Most of these factors changed towards higher activity friendliness. Changes in the perceived environment were only limitedly related to changes in children's physical activity. Copyright © 2015 Elsevier Ltd. All rights reserved.

Risk Assessment for Children Exposed to Arsenic on Baseball Fields with Contaminated Fill Material

PubMed Central

Ferguson, Alesia C.; Black, Jennifer C.; Sims, Isaac B.; Welday, Jennifer N.; Elmir, Samir M.; Goff, Kendra F.; Higginbotham, J. Mark

2018-01-01

Children can be exposed to arsenic through play areas which may have contaminated fill material from historic land use. The objective of the current study was to evaluate the risk to children who play and/or spend time at baseball fields with soils shown to have arsenic above background levels. Arsenic in soils at the study sites located in Miami, FL, USA showed distinct distributions between infield, outfield, and areas adjacent to the fields. Using best estimates of exposure factors for children baseball scenarios, results show that non-cancer risks depend most heavily upon the age of the person and the arsenic exposure level. For extreme exposure scenarios evaluated in this study, children from 1 to 2 years were at highest risk for non-cancer effects (Hazard Quotient, HQ > 2.4), and risks were higher for children exhibiting pica (HQ > 9.7) which shows the importance of testing fill for land use where children may play. At the study sites, concentration levels of arsenic resulted in a range of computed cancer risks that differed by a factor of 10. In these sites, the child’s play position also affected risk. Outfield players, with a lifetime exposure to these arsenic levels, could have 10 times more increased chance of experiencing cancers associated with arsenic (i.e., lung, bladder, skin) in comparison to infielders. The distinct concentration distributions observed between these portions of the baseball fields emphasize the need to delineate contaminated areas in public property where citizens may spend more free time. This study also showed a need for more tools to improve the risk estimates for child play activities. For instance, more refined measurements of exposure factors for intake (e.g., inhalation rates under rigorous play activities, hand to mouth rates), exposure frequency (i.e., time spent in various activities) and other exposure factors (e.g., soil particulate emission rates at baseball play fields) can help pinpoint risk on baseball fields where arsenic levels may be a concern. PMID:29300352

ATP during early bladder stretch is important for urgency in detrusor overactivity patients.

PubMed

Cheng, Y; Mansfield, K J; Allen, W; Chess-Williams, R; Burcher, E; Moore, K H

2014-01-01

ATP is an important mediator of urgency in women with detrusor overactivity (DO). In order to understand how different degrees of bladder stretch elicited ATP release in DO patients compared with controls, sequential aliquots were collected during cystometry and ATP release was measured at each degree of bladder filling, in female patients with DO and controls. In both DO and control groups, ATP release was induced during bladder filling, suggesting that stretch stimulated further ATP release. However, the luminal ATP concentrations were already high at early filling stage (200 mL), which was even greater than those at the later filling stages (400 mL and maximum cystometric capacity, MCC), indicating that a substantial ATP release has been induced during early filling (200 mL) in both DO and controls. In DO, ATP release at 200 mL was significantly higher in those with low first desire to void (FDV) (≤ 200 mL) than in those with higher FDV (> 200 mL); this may suggest that ATP release at early stretch may play an important role in urgency (early sensation) in DO. ATP concentrations remained unchanged after voiding, suggesting that voiding did not further induce ATP release into intraluminal fluid.

Quality aspects of ex vivo root canal treatments done by undergraduate dental students using four different endodontic treatment systems.

PubMed

Jungnickel, Luise; Kruse, Casper; Vaeth, Michael; Kirkevang, Lise-Lotte

2018-04-01

To evaluate factors associated with treatment quality of ex vivo root canal treatments performed by undergraduate dental students using different endodontic treatment systems. Four students performed root canal treatment on 80 extracted human teeth using four endodontic treatment systems in designated treatment order following a Latin square design. Lateral seal and length of root canal fillings was radiographically assessed; for lateral seal, a graded visual scale was used. Treatment time was measured separately for access preparation, biomechanical root canal preparation, obturation and for the total procedure. Mishaps were registered. An ANOVA mirroring the Latin square design was performed. Use of machine-driven nickel-titanium systems resulted in overall better quality scores for lateral seal than use of the manual stainless-steel system. Among systems with machine-driven files, scores did not significantly differ. Use of machine-driven instruments resulted in shorter treatment time than manual instrumentation. Machine-driven systems with few files achieved shorter treatment times. With increasing number of treatments, root canal-filling quality increased, treatment time decreased; a learning curve was plotted. No root canal shaping file separated. The use of endodontic treatment systems with machine-driven files led to higher quality lateral seal compared to the manual system. The three contemporary machine-driven systems delivered comparable results regarding quality of root canal fillings; they were safe to use and provided a more efficient workflow than the manual technique. Increasing experience had a positive impact on the quality of root canal fillings while treatment time decreased.

Filling defects in the pancreatic duct on endoscopic retrograde pancreatography.

PubMed

Taylor, A J; Carmody, T J; Schmalz, M J; Wiedmeyer, D A; Stewart, E T

1992-12-01

Filling defects in the pancreatic duct are a frequent finding during endoscopic retrograde pancreatography (ERP) and have a variety of causes. Some filling defects may be artifactual or related to technical factors and, once their origin is recognized, can be disregarded. Others may be due to acute changes of pancreatitis and should prompt more careful injection of contrast material into the duct. Intraluminal masses may represent calculi or a neoplasm, either of which may require surgery or endoscopic intervention. The exact nature of these filling defects may not be apparent on radiographs, and other studies may be needed. This article reviews our approach to the evaluation of filling defects in the pancreatic duct.

Assessment of the impact that the capsule fill tube has on implosions conducted with high density carbon ablators

NASA Astrophysics Data System (ADS)

Pak, Arthur; Benedetti, L. R.; Berzak Hopkins, L. F.; Clark, D.; Divol, L.; Dewald, E. L.; Fittinghoff, D.; Izumi, N.; Khan, S. F.; Landen, O.; Lepape, S.; Ma, T.; Marley, E.; Nagel, S.; Volegov, P.; Weber, C.; Bradley, D. K.; Callahan, D.; Grim, G.; Hurricane, O. A.; Patel, P.; Schneider, M. B.; Edwards, M. J.

2017-10-01

In recent inertial confinement implosion experiments conducted at the National Ignition Facility, bright and spatially localized x-ray emission within the hot spot at stagnation has been observed. This emission is associated with higher Z ablator material that is injected into the hot spot by the hydrodynamic perturbation induced by the 5-10 um diameter capsule fill tube. The reactivity of the DT fuel and subsequent yield of the implosion are strongly dependent on the density, temperature, and confinement time achieved throughout the stagnation of the implosion. Radiative losses from higher Z ablator material that mixes into the hot spot as well as non-uniformities in the compression and confinement induced by the fill tube perturbation can degrade the yield of the implosion. This work will examine the impact to conditions at stagnation that results from the fill tube perturbation. This assessment will be based from a pair of experiments conducted with a high density carbon ablator where the only deliberate change was reduction in fill tube diameter from 10 to 5 um. An estimate of the radiative losses and impact on performance from ablator mix injected into the hot spot by the fill tube perturbation will be presented. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Using Temporal Fill Factor to Reduce Frame Reconstruction Rates

NASA Technical Reports Server (NTRS)

Larimer, James; Balram, Nikhil; Gille, Jennifer; Luszcz, Jeffery

1997-01-01

The newer active matrix display technologies such as TFT-LCD, DMD, PDP maintain their pixel values through the entire frame time, presenting a 100% temporal fill factor, in contrast to the duty cycle produced by the phosphor impulse response of the CRT. This sample-and-hold characteristic can be exploited to lower the displayed frame rate without affecting visual quality. The lower frame rate results in significantly lower transmission bandwidth, power, and cost.

Rear surface effects in high efficiency silicon solar cells

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wenham, S.R.; Robinson, S.J.; Dai, X.

1994-12-31

Rear surface effects in PERL solar cells can lead not only to degradation in the short circuit current and open circuit voltage, but also fill factor. Three mechanisms capable of changing the effective rear surface recombination velocity with injection level are identified, two associated with oxidized p-type surfaces, and the third with two dimensional effects associated with a rear floating junction. Each of these will degrade the fill factor if the range of junction biases corresponding to the rear surface transition, coincides with the maximum power point. Despite the identified non idealities, PERL cells with rear floating junctions (PERF cells)more » have achieved record open circuit voltages for silicon solar cells, while simultaneously achieving fill factor improvements relative to standard PERL solar cells. Without optimization, a record efficiency of 22% has been demonstrated for a cell with a rear floating junction. The results of both theoretical and experimental studies are provided.« less

Designing ternary blend bulk heterojunction solar cells with reduced carrier recombination and a fill factor of 77%

NASA Astrophysics Data System (ADS)

Gasparini, Nicola; Jiao, Xuechen; Heumueller, Thomas; Baran, Derya; Matt, Gebhard J.; Fladischer, Stefanie; Spiecker, Erdmann; Ade, Harald; Brabec, Christoph J.; Ameri, Tayebeh

2016-09-01

In recent years the concept of ternary blend bulk heterojunction (BHJ) solar cells based on organic semiconductors has been widely used to achieve a better match to the solar irradiance spectrum, and power conversion efficiencies beyond 10% have been reported. However, the fill factor of organic solar cells is still limited by the competition between recombination and extraction of free charges. Here, we design advanced material composites leading to a high fill factor of 77% in ternary blends, thus demonstrating how the recombination thresholds can be overcome. Extending beyond the typical sensitization concept, we add a highly ordered polymer that, in addition to enhanced absorption, overcomes limits predicted by classical recombination models. An effective charge transfer from the disordered host system onto the highly ordered sensitizer effectively avoids traps of the host matrix and features an almost ideal recombination behaviour.

New dual-curvature microlens array with a high fill-factor for organic light emitting diode modules

NASA Astrophysics Data System (ADS)

Lin, Tsung-Hung; Yang, Hsiharng; Chao, Ching-Kong; Shui, Hung-Chi

2013-09-01

A new method for fabricating a novel dual-curvature microlens array with a high fill-factor using proximity printing in a lithography process is reported. The lens shapes include dual-curvature, which is a novel shape composed of triangles and hexagons. We utilized UV proximity printing by controlling a printing gap between the mask and substrate. The designed high density microlens array pattern can fabricate a dual-curvature microlens array with a high fill-factor in a photoresist material. It is due to the UV light diffraction which deflects away from the aperture edges and produces a certain exposure in the photoresist material outside the aperture edges. A dual-curvature microlens array with a height ratio of 0.48 can boost axial luminance up to 22%. Therefore, the novel dual-curvature microlens array offers an economical solution for increasing the luminance of organic light emitting diodes.

External cardiac compression may be harmful in some scenarios of pulseless electrical activity.

PubMed

Hogan, T S

2012-10-01

Pulseless electrical activity occurs when organised or semi-organised electrical activity of the heart persists but the product of systemic vascular resistance and the increase in systemic arterial flow generated by the ejection of the left venticular stroke volume is not sufficient to produce a clinically detectable pulse. Pulseless electrical activity encompasses a very heterogeneous variety of severe circulatory shock states ranging in severity from pseudo-cardiac arrest to effective cardiac arrest. Outcomes of cardiopulmonary resuscitation for pulseless electrical activity are generally poor. Impairment of cardiac filling is the limiting factor to cardiac output in many scenarios of pulseless electrical activity, including extreme vasodilatory shock states. There is no evidence that external cardiac compression can increase cardiac output when impaired cardiac filling is the limiting factor to cardiac output. If impaired cardiac filling is the limiting factor to cardiac output and the heart is effectively ejecting all the blood returning to it, then external cardiac compression can only increase cardiac output if it increases venous return and cardiac filling. Repeated cardiac compression asynchronous with the patient's cardiac cycle and raised mean intrathoracic pressure due to chest compression can be expected to reduce rather than to increase cardiac filling and therefore to reduce rather than to increase cardiac output in such circumstances. The hypothesis is proposed that the performance of external cardiac compression will have zero or negative effect on cardiac output in pulseless electrical activity when impaired cardiac filling is the limiting factor to cardiac output. External cardiac compression may be both directly and indirectly harmful to significant sub-groups of patients with pulseless electrical activity. We have neither evidence nor theory to provide comfort that external cardiac compression is not harmful in many scenarios of pulseless electrical activity. Investigation using a variety of animal models of pulseless electrical activity produced by different shock-inducing mechanisms is required to provide an evidence base for resuscitation guidelines. Copyright © 2012 Elsevier Ltd. All rights reserved.

Psychometric Properties of the Psychological Vulnerability Scale in Higher Education Students.

PubMed

Nogueira, Maria José; Barros, Luisa; Sequeira, Carlos

2017-05-01

Psychological vulnerability is related to cognitive beliefs that reflect dependence on one's sense of self-worth and to maladaptive functioning. It is a disadvantage that renders people less protected to face negative life experiences. The purpose of this study was to adapt and test the psychometric properties of the Psychological Vulnerability Scale in a sample of 267 Portuguese higher education students. A psychometric study of the Psychological Vulnerability Scale, after translation into Portuguese, was performed with a convenience sample of higher education students. Participants were asked to fill in the sociodemographic questionnaire, the Psychological Vulnerability Scale, the Brief Symptom Inventory, and a one-item question about the Perception of Vulnerability. The mean age of the participants was 20.5 years ( SD = 3.3). A factor analysis confirmed the original one-factor structure, explaining 42.9% of the total variance. The Psychological Vulnerability Scale showed adequate internal consistency and excellent test-retest stability. Convergent validity was confirmed by positive correlations with the Brief Symptom Inventory and Perception of Vulnerability. Overall, the Psychological Vulnerability Scale showed good validity, reliability, and stability over time. The Psychological Vulnerability Scale is now ready to be used by practitioners and researchers to measure the psychological vulnerability among Portuguese higher education students. These data add to the body of knowledge of psychiatric and mental health nursing and provides support for the use of the Psychological Vulnerability Scale in higher education students.

Modeling posttraumatic growth among cancer patients: The roles of social support, appraisals, and adaptive coping.

PubMed

Cao, Weidan; Qi, Xiaona; Cai, Deborah A; Han, Xuanye

2018-01-01

The purpose of the study was to build a model to explain the relationships between social support, uncontrollability appraisal, adaptive coping, and posttraumatic growth (PTG) among cancer patients in China. The participants who were cancer patients in a cancer hospital in China filled out a survey. The final sample size was 201. Structural equation modeling was used to build a model explaining PTG. Structural equation modeling results indicated that higher levels of social support predicted higher levels of adaptive coping, higher levels of uncontrollability appraisal predicted lower levels of adaptive coping, and higher levels of adaptive coping predicted higher levels of PTG. Moreover, adaptive coping was a mediator between social support and growth, as well as a mediator between uncontrollability and growth. The direct effects of social support and uncontrollability on PTG were insignificant. The model demonstrated the relationships between social support, uncontrollability appraisal, adaptive coping, and PTG. It could be concluded that uncontrollability appraisal was a required but not sufficient condition for PTG. Neither social support nor uncontrollability appraisal had direct influence on PTG. However, social support and uncontrollability might indirectly influence PTG, through adaptive coping. It implies that both internal factors (eg, cognitive appraisal and coping) and external factors (eg, social support) are required in order for growth to happen. Copyright © 2017 John Wiley & Sons, Ltd.

Slotted Polyimide-Aerogel-Filled-Waveguide Arrays

NASA Technical Reports Server (NTRS)

Rodriguez-Solis, Rafael A.; Pacheco, Hector L.; Miranda, Felix A.; Meador, Mary Ann B.

2013-01-01

Polyimide aerogels were considered to serve as a filling for millimeter-wave waveguides. While these waveguides present a slightly higher loss than hollow waveguides, they have less losses than Duroid substrate integrated waveguides (less than 0.15 dB at Ka-band, in a 20 mm section), and exhibit an order of magnitude of mass reduction when compared to commercial waveguides. A Ka-band slotted aerogel-filled-waveguide array was designed, which provided the same gain (9 dBi) as its standard waveguide counterpart, and a slotted aerogel-filled-waveguide array using folded-slots was designed for comparison, obtaining a gain of 9 dB and a bandwidth of 590 MHz.

Left ventricular diastolic dysfunction without left ventricular hypertrophy in obese children and adolescents: a Tissue Doppler Imaging and Cardiac Troponin I Study.

PubMed

El Saiedi, Sonia A; Mira, Marwa F; Sharaf, Sahar A; Al Musaddar, Maysoun M; El Kaffas, Rania M H; AbdelMassih, Antoine F; Barsoum, Ihab H Y

2018-01-01

Obesity increases the risk for various cardiovascular problems. Increase in body mass index is often an independent risk factor for the development of elevated blood pressure and clustering of various cardiovascular risk factors. To determine early markers of left ventricular affection in obese patients before the appearance of left ventricular hypertrophy. In this cross-sectional study, we evaluated 42 obese patients and 30 healthy controls. Their ages ranged from 6 to 19 years. Studied children were subjected to anthropometric, lipid profile, and serum Troponin I level measurements. Echocardiographic evaluation performed to assess the left ventricle included left ventricular dimension measurement using motion-mode echocardiography, based on which patients with left ventricular hypertrophy (10 patients) were eliminated, as well as conventional and tissue Doppler imaging. Tissue Doppler findings in the study groups showed that the ratio of transmitral early diastolic filling velocity to septal peak early diastolic myocardial velocity (E/e') was significantly higher in cases compared with controls [6.9±1.4 versus 9.0±1.6, p (Pearson's coefficient)=0.001, respectively]. The level of cardiac troponin I was significantly higher in cases compared with controls [0.14±0.39 ng/ml versus 0.01±0.01 ng/ml, p (Pearson's coefficient)=0.047, respectively] and there was a significant correlation between troponin I and transmitral early diastolic filling velocity to septal peak early diastolic myocardial velocity ratio (E/e') [R (correlation coefficient)=0.6]. Tissue Doppler Imaging and Troponin I evaluation proved useful tools to detect early affection of the left ventricle in obese patients even in the absence of left ventricular hypertrophy.

A Fuzzy Rule-Base Model for Classification of Spirometric FVC Graphs in Chronical Obstructive Pulmonary Diseases

DTIC Science & Technology

2001-10-25

questionnaire was filled out before test which is very important criteria for each subject for investigating are smoking cigarettes, having asthma, chronic...9, 12]. Secondly, observed FVC and FEV1 data plotted are taken under investigation. According to the questionnaire filled out, subjects... questionnaire filled in by each subject on the result of the diagnosing (categorizing FVC graphs) COPD, elimination of erroneous factors affecting

Training the Trainers: Mission Analysis and Support for USAR Training Divisions

DTIC Science & Technology

1991-03-25

the Department of Defense (DOD),! mobilization expansion is a key factor In Limited Mobilization9 or Graduated Military Responseio theories of...less filled units of their personnel to fill earlier deploying units. After stripping units at random with 19 disastrous morale results it was decided...28 assigned) once all companies In the division are filled. This mission is identified in the unit’s Table of Distribution and Allowance ( TDA ) and

Intermittent surface water connectivity: Fill and spill vs. fill and merge dynamics

USGS Publications Warehouse

Leibowitz, Scott G.; Mushet, David M.; Newton, Wesley E.

2016-01-01

Intermittent surface connectivity can influence aquatic systems, since chemical and biotic movements are often associated with water flow. Although often referred to as fill and spill, wetlands also fill and merge. We examined the effects of these connection types on water levels, ion concentrations, and biotic communities of eight prairie pothole wetlands between 1979 and 2015. Fill and spill caused pulsed surface water connections that were limited to periods following spring snow melt. In contrast, two wetlands connected through fill and merge experienced a nearly continuous, 20-year surface water connection and had completely coincident water levels. Fill and spill led to minimal convergence in dissolved ions and macroinvertebrate composition, while these constituents converged under fill and merge. The primary factor determining differences in response was duration of the surface water connection between wetland pairs. Our findings suggest that investigations into the effects of intermittent surface water connections should not consider these connections generically, but need to address the specific types of connections. In particular, fill and spill promotes external water exports while fill and merge favors internal storage. The behaviors of such intermittent connections will likely be accentuated under a future with more frequent and severe climate extremes.

Filling the blanks in temporal intervals: the type of filling influences perceived duration and discrimination performance

PubMed Central

Horr, Ninja K.; Di Luca, Massimiliano

2015-01-01

In this work we investigate how judgments of perceived duration are influenced by the properties of the signals that define the intervals. Participants compared two auditory intervals that could be any combination of the following four types: intervals filled with continuous tones (filled intervals), intervals filled with regularly-timed short tones (isochronous intervals), intervals filled with irregularly-timed short tones (anisochronous intervals), and intervals demarcated by two short tones (empty intervals). Results indicate that the type of intervals to be compared affects discrimination performance and induces distortions in perceived duration. In particular, we find that duration judgments are most precise when comparing two isochronous and two continuous intervals, while the comparison of two anisochronous intervals leads to the worst performance. Moreover, we determined that the magnitude of the distortions in perceived duration (an effect akin to the filled duration illusion) is higher for tone sequences (no matter whether isochronous or anisochronous) than for continuous tones. Further analysis of how duration distortions depend on the type of filling suggests that distortions are not only due to the perceived duration of the two individual intervals, but they may also be due to the comparison of two different filling types. PMID:25717310

Stress levels of critical care doctors in India: A national survey

PubMed Central

Amte, Rahul; Munta, Kartik; Gopal, Palepu B.

2015-01-01

Background: Doctors working in critical care units are prone to higher stress due to various factors such as higher mortality and morbidity, demanding service conditions and need for higher knowledge and technical skill. Aim: The aim was to evaluate the stress level and the causative stressors in doctors working in critical care units in India. Materials and Methods: A two modality questionnaire-based cross-sectional survey was conducted. In manual mode, randomly selected delegates attending the annual congress of Indian Society of Critical Care Medicine filled the questionnaire. In the electronic mode, the questionnaires were E-mailed to critical care doctors. These questionnaires were based on General Health Questionnaire-12 (GHQ-12). Completely filled 242 responses were utilized for comparative and correlation analysis. Results: Prevalence of moderate to severe stress level was 40% with a mean score of 2 on GHQ-12 scale. Too much responsibility at times and managing VIP patients ranked as the top two stressors studied, while the difficult relationship with colleagues and sexual harassment were the least. Intensivists were spending longest hours in the Intensive Care Unit (ICU) followed by pulmonologists and anesthetists. The mean number of ICU bed critical care doctors entrusted with was 13.2 ± 6.3. Substance abuse to relieve stress was reported as alcohol (21%), anxiolytic or antidepressants (18%) and smoking (14%). Conclusion: Despite the higher workload, stress levels measured in our survey in Indian critical care doctors were lower compared to International data. Substantiation of this data through a wider study and broad-based measures to improve the quality of critical care units and quality of the lives of these doctors is the need of the hour. PMID:25983431

Stress levels of critical care doctors in India: A national survey.

PubMed

Amte, Rahul; Munta, Kartik; Gopal, Palepu B

2015-05-01

Doctors working in critical care units are prone to higher stress due to various factors such as higher mortality and morbidity, demanding service conditions and need for higher knowledge and technical skill. The aim was to evaluate the stress level and the causative stressors in doctors working in critical care units in India. A two modality questionnaire-based cross-sectional survey was conducted. In manual mode, randomly selected delegates attending the annual congress of Indian Society of Critical Care Medicine filled the questionnaire. In the electronic mode, the questionnaires were E-mailed to critical care doctors. These questionnaires were based on General Health Questionnaire-12 (GHQ-12). Completely filled 242 responses were utilized for comparative and correlation analysis. Prevalence of moderate to severe stress level was 40% with a mean score of 2 on GHQ-12 scale. Too much responsibility at times and managing VIP patients ranked as the top two stressors studied, while the difficult relationship with colleagues and sexual harassment were the least. Intensivists were spending longest hours in the Intensive Care Unit (ICU) followed by pulmonologists and anesthetists. The mean number of ICU bed critical care doctors entrusted with was 13.2 ± 6.3. Substance abuse to relieve stress was reported as alcohol (21%), anxiolytic or antidepressants (18%) and smoking (14%). Despite the higher workload, stress levels measured in our survey in Indian critical care doctors were lower compared to International data. Substantiation of this data through a wider study and broad-based measures to improve the quality of critical care units and quality of the lives of these doctors is the need of the hour.

Dynamic mechanical analysis of waste tyre rubber filled brake friction composite materials

NASA Astrophysics Data System (ADS)

Rathi, Mukesh Kumar; Singh, Tej; Chauhan, Ranchan

2018-05-01

In this research work, the dynamic mechanical properties of waste tyre rubber filled friction composites were studied. Four friction composites with varying amount of waste rubber (0, 4, 8, 12 wt.%) and barium sulphate (38, 42, 46, 50 wt.%) were designed and fabricated as per industrial norms. Dynamic mechanical analysis has been carried out to characterize the storage modulus, loss modulus and damping factor of the fabricated friction composite. Experimental results indicated that storage modulus decreases with increasing waste rubber content up to particular loading (4 wt.%), and after that it increases with further loading. The loss modulus of the composites increases steadily with increasing waste rubber content whereas, damping factor remain maximum for 12 wt.% waste rubber filled friction composites.

Employing Lead Thiocyanate Additive to Reduce the Hysteresis and Boost the Fill Factor of Planar Perovskite Solar Cells.

PubMed

Ke, Weijun; Xiao, Chuanxiao; Wang, Changlei; Saparov, Bayrammurad; Duan, Hsin-Sheng; Zhao, Dewei; Xiao, Zewen; Schulz, Philip; Harvey, Steven P; Liao, Weiqiang; Meng, Weiwei; Yu, Yue; Cimaroli, Alexander J; Jiang, Chun-Sheng; Zhu, Kai; Al-Jassim, Mowafak; Fang, Guojia; Mitzi, David B; Yan, Yanfa

2016-07-01

Lead thiocyanate in the perovskite precursor can increase the grain size of a perovskite thin film and reduce the conductivity of the grain boundaries, leading to perovskite solar cells with reduced hysteresis and enhanced fill factor. A planar perovskite solar cell with grain boundary and interface passivation achieves a steady-state efficiency of 18.42%. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Spatial Light Modulators and Applications: Summaries of Papers Presented at the Spatial Light Modulators and Applications Topical Meeting Held on March 15-17, 1993 in Palm Springs, California

DTIC Science & Technology

1993-03-17

modulator: Number of Elements 16 x 16 Pixel Size 1 mmxl mm Area Fill Factor > 90% Reflectance > 90% Phase Shift 900 Frame Rate > 1 kHz Operational Spectral...electro-optic constants. By using reflected light from the second interface a factor of two increase in phase shift is obtained for an applied voltage vs...wavelengths in general require thinner PLZT wafers. One of the objectives of the SLM design was to maximize pixel area fill factor and thereby the

Geospatial data to support analysis of water-quality conditions in basin-fill aquifers in the southwestern United States

USGS Publications Warehouse

McKinney, Tim S.; Anning, David W.

2009-01-01

The Southwest Principal Aquifers study area consists of most of California and Nevada and parts of Utah, Arizona, New Mexico, and Colorado; it is about 409,000 square miles. The Basin-fill aquifers extend through about 201,000 square miles of the study area and are the primary source of water for cities and agricultural communities in basins in the arid and semiarid southwestern United States (Southwest). The demand on limited ground-water resources in areas in the southwestern United States has increased significantly. This increased demand underscores the importance of understanding factors that affect the water quality in basin-fill aquifers in the region, which are being studied through the U.S. Geological Survey's National Water-Quality Assessment (NAWQA) program. As a part of this study, spatial datasets of natural and anthropogenic factors that may affect ground-water quality of the basin-fill aquifers in the southwestern United States were developed. These data include physical characteristics of the region, such as geology, elevation, and precipitation, as well as anthropogenic factors, including population, land use, and water use. Spatial statistics for the alluvial basins in the Southwest have been calculated using the datasets. This information provides a foundation for the development of conceptual and statistical models that relate natural and anthropogenic factors to ground-water quality across the Southwest. A geographic information system (GIS) was used to determine and illustrate the spatial distribution of these basin-fill variables across the region. One hundred-meter resolution raster data layers that represent the spatial characteristics of the basins' boundaries, drainage areas, population densities, land use, and water use were developed for the entire Southwest.

Effective g-factors of carriers in inverted InAs/GaSb bilayers

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mu, Xiaoyang; Collaborative Innovation Center of Quantum Matter, Beijing 100871; Sullivan, Gerard

2016-01-04

We perform tilt-field transport experiment on inverted InAs/GaSb, which hosts quantum spin Hall insulator. By means of coincidence method, Landau level (LL) spectra of electron and hole carriers are systematically studied at different carrier densities tuned by gate voltages. When Fermi level stays in the conduction band, we observe LL crossing and anti-crossing behaviors at odd and even filling factors, respectively, with a corresponding g-factor of 11.5. It remains nearly constant for varying filling factors and electron densities. On the contrary, for GaSb holes, only a small Zeeman splitting is observed even at large tilt angles, indicating a g-factor ofmore » less than 3.« less

Effects of natural and human factors on groundwater quality of basin-fill aquifers in the southwestern United States-conceptual models for selected contaminants

USGS Publications Warehouse

Bexfield, Laura M.; Thiros, Susan A.; Anning, David W.; Huntington, Jena M.; McKinney, Tim S.

2011-01-01

As part of the U.S. Geological Survey National Water-Quality Assessment (NAWQA) Program, the Southwest Principal Aquifers (SWPA) study is building a better understanding of the factors that affect water quality in basin-fill aquifers in the Southwestern United States. The SWPA study area includes four principal aquifers of the United States: the Basin and Range basin-fill aquifers in California, Nevada, Utah, and Arizona; the Rio Grande aquifer system in New Mexico and Colorado; and the California Coastal Basin and Central Valley aquifer systems in California. Similarities in the hydrogeology, land- and water-use practices, and water-quality issues for alluvial basins within the study area allow for regional analysis through synthesis of the baseline knowledge of groundwater-quality conditions in basins previously studied by the NAWQA Program. Resulting improvements in the understanding of the sources, movement, and fate of contaminants are assisting in the development of tools used to assess aquifer susceptibility and vulnerability.This report synthesizes previously published information about the groundwater systems and water quality of 15 information-rich basin-fill aquifers (SWPA case-study basins) into conceptual models of the primary natural and human factors commonly affecting groundwater quality with respect to selected contaminants, thereby helping to build a regional understanding of the susceptibility and vulnerability of basin-fill aquifers to those contaminants. Four relatively common contaminants (dissolved solids, nitrate, arsenic, and uranium) and two contaminant classes (volatile organic compounds (VOCs) and pesticide compounds) were investigated for sources and controls affecting their occurrence and distribution above specified levels of concern in groundwater of the case-study basins. Conceptual models of factors that are important to aquifer vulnerability with respect to those contaminants and contaminant classes were subsequently formed. The conceptual models are intended in part to provide a foundation for subsequent development of regional-scale statistical models that relate specific constituent concentrations or occurrence in groundwater to natural and human factors.

Dithienogermole as a fused electron donor in bulk heterojunction solar cells.

PubMed

Amb, Chad M; Chen, Song; Graham, Kenneth R; Subbiah, Jegadesan; Small, Cephas E; So, Franky; Reynolds, John R

2011-07-06

We report the synthesis and bulk heterojunction photovoltaic performance of the first dithienogermole (DTG)-containing conjugated polymer. Stille polycondensation of a distannyl-DTG derivative with 1,3-dibromo-N-octyl-thienopyrrolodione (TPD) results in an alternating copolymer which displays light absorption extending to 735 nm, and a higher HOMO level than the analogous copolymer containing the commonly utilized dithienosilole (DTS) heterocycle. When polyDTG-TPD:PC(70)BM blends are utilized in inverted bulk heterojunction solar cells, the cells display average power conversion efficiencies of 7.3%, compared to 6.6% for the DTS-containing cells prepared in parallel under identical conditions. The performance enhancement is a result of a higher short-circuit current and fill factor in the DTG-containing cells, which comes at the cost of a slightly lower open circuit voltage than for the DTS-based cells.

Effect of filler loading of characteristic natural rubber latex (NRL) film filled with nanocrystal cellulose (NCC) and dipersion agent polyvinylpyrrolidone (PVP)

NASA Astrophysics Data System (ADS)

Harahap, Hamidah; Lubis, Yuni Aldriani; Taslim, Iriany, Nasution, Halimatuddahliana; Agustini, Hamda Eka

2018-04-01

A study has been conducted on the effect of filler loading on NRL films filled with NCC from corn cob waste. This study reviews on the filler loading of NRL film characteristics. The process begins with the production of NCC filler and then proceed with the production NRL film which is processed by coagulant dipping method. NRL is filled with NCC and PVP as dispersion agent of 2, 4, 3, 8 grams (filler loading) and 1% PVP by weight. The production of NRL film started with pre-vulcanization process at 70 °C and followed by vulcanization process at 110 °C for 20 minutes. The results showed that higher filler loading improved the higher crosslink density and mechanical properties of NRL film.

Filling the IT Leadership Pipeline: A Panel Discussion

ERIC Educational Resources Information Center

Maas, Bruce; Paige, Brian; Ridley, Michael; Rowe, Theresa; Wandschneider, Bo; Woo, Melissa

2012-01-01

The role of the Chief Information Officer (CIO) in higher education is continuously changing, and the career path to becoming a CIO is not always well defined. As campuses consider succession planning, and as CIOs and those who hope to become CIOs think about filling the IT leadership "pipeline," the transformation both of information…

Permanent magnet machine with windings having strand transposition

DOEpatents

Qu, Ronghai; Jansen, Patrick Lee

2009-04-21

This document discusses, among other things, a stator with transposition between the windings or coils. The coils are free from transposition to increase the fill factor of the stator slots. The transposition at the end connections between an inner coil and an outer coil provide transposition to reduce circulating current loss. The increased fill factor reduces further current losses. Such a stator is used in a dual rotor, permanent magnet machine, for example, in a compressor pump, wind turbine gearbox, wind turbine rotor.

Risk factors associated with chronic low back pain in Syria.

PubMed

Alhalabi, Mohammad Salem; Alhaleeb, Hassan; Madani, Sarah

2015-01-01

We aimed to identify risk factors associated with chronic low back pain (C-LBP) in Syria. We conducted the study in a busy outpatient neurology clinic in Damascus city from October 2011 to August 2012. We enrolled all eligible adults presenting with C-LBP along with those who denied any back pain as a controls. We considered C-LBP any LBP lasting over 3 months. We developed our own questionnaire. A clinical nurse interviewed each person and filled in the results. We had a total of 911 subjects; 513 patients and 398 controls. We found that C-LBP increased with age. Having a sibling with C-LBP was a strong predictor of C-LBP. In women obesity, but not overweight, was a risk factor. Number of children was a risk factor for mothers. Higher level of education decreased the chance of C-LBP in women. Sedentary job increased the risk of C-LBP. This study sheds some light on risk factors for C-LBP in our population and might help find possible preventive measures.

Dental caries among disadvantaged 3- to 4-year-old children in northern Manhattan.

PubMed

Albert, David A; Park, Katherine; Findley, Sally; Mitchell, Dennis A; McManus, Joseph M

2002-01-01

The study was conducted to determine the prevalence of early childhood caries (ECC), untreated caries, and the ratio of posterior to anterior caries in a disadvantaged predominantly Hispanic or African-American urban population. Data are compared to NHANES III to assess the caries burden in our cohort. Comparisons are made to the aggregate and to minorities within the national database. A retrospective chart review was conducted for children enrolled in a Head Start or day care program in the communities of Washington-Heights and Central and East Harlem and seen on the community organization's mobile dental van between 1995 and 1997. The study included only children 3 to 4 years of age at the initial examination (n=1,605). A single examiner provided all the examinations. The mean number of decayed and filled surfaces (dfs), decayed surfaces (ds) and filled surfaces (fs), the percentage of decayed of total decayed and filled surfaces (%d/dfs), decayed and filled teeth (dft), decayed teeth (dt) and filled teeth (ft), and the percentage of decayed of total decayed and filled teeth (%d/dft) were calculated. Posterior vs anterior d, f, dft, dfs and d-anterior/total d, and d-posterior/total d were tabulated. Northern Manhattan data was tabulated and compared to NHANES III (1988-1994) in the aggregate and for subpopulations categorized by gender and ethnicity. All results are also reported for children with at least one decayed or filled tooth. T-tests were used to assess for significant differences. There was even representation of males (50%) and females (50%). Mean dft was 1.08 overall, and 3.14 for children with dft>0. The level of untreated decay, %d/ dft, was 91%, significantly higher than the US national population which is 76% overall, and 76% for African Americans and Mexican Americans within the US national population. The children in this population have higher caries prevalence and a higher level of untreated caries than the national means as reported in NHANES III. The high level of untreated decay found in this particularly disadvantaged community suggests that enhanced dental services targeting the very young are needed in these communities.

22.5% efficient silicon heterojunction solar cell with molybdenum oxide hole collector

DOE Office of Scientific and Technical Information (OSTI.GOV)

Geissbühler, Jonas, E-mail: jonas.geissbuehler@epfl.ch; Werner, Jérémie; Martin de Nicolas, Silvia

2015-08-24

Substituting the doped amorphous silicon films at the front of silicon heterojunction solar cells with wide-bandgap transition metal oxides can mitigate parasitic light absorption losses. This was recently proven by replacing p-type amorphous silicon with molybdenum oxide films. In this article, we evidence that annealing above 130 °C—often needed for the curing of printed metal contacts—detrimentally impacts hole collection of such devices. We circumvent this issue by using electrodeposited copper front metallization and demonstrate a silicon heterojunction solar cell with molybdenum oxide hole collector, featuring a fill factor value higher than 80% and certified energy conversion efficiency of 22.5%.

Organic Solar Cells Based on a 2D Benzo[1,2-b:4,5-b']difuran-Conjugated Polymer with High-Power Conversion Efficiency.

PubMed

Huo, Lijun; Liu, Tao; Fan, Bingbing; Zhao, Zhiyuan; Sun, Xiaobo; Wei, Donghui; Yu, Mingming; Liu, Yunqi; Sun, Yanming

2015-11-18

A novel 2D benzodifuran (BDF)-based copolymer (PBDF-T1) is synthesized. Polymer solar cells fabricated with PBDF-T1 show high power conversion efficiency of 9.43% and fill factor of 77.4%, which is higher than the performance of its benzothiophene (BDT) counterpart (PBDT-T1). These results provide important progress for BDF-based copolymers and demonstrate that BDF-based copolymers can be competitive with the well-studied BDT counterparts via molecular structure design and device optimization. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Parylene-based active micro space radiator with thermal contact switch

DOE Office of Scientific and Technical Information (OSTI.GOV)

Ueno, Ai; Suzuki, Yuji

2014-03-03

Thermal management is crucial for highly functional spacecrafts exposed to large fluctuations of internal heat dissipation and/or thermal boundary conditions. Since thermal radiation is the only means for heat removal, effective control of radiation is required for advanced space missions. In the present study, a MEMS (Micro Electro Mechanical Systems) active radiator using the contact resistance change has been proposed. Unlike previous bulky thermal louvers/shutters, higher fill factor can be accomplished with an array of electrostatically driven micro diaphragms suspended with polymer tethers. With an early prototype developed with parylene MEMS technologies, radiation heat flux enhancement up to 42% hasmore » been achieved.« less

Photovoltaic static concentrator analysis

NASA Astrophysics Data System (ADS)

Almonacid, G.; Luque, A.; Molledo, A. G.

1984-12-01

Ray tracing is the basis of the present analysis of truncated bifacial compound parabolic concentrators filled with a dielectric substance, which are of interest in photovoltaic applications where the bifacial cells allow higher static concentrations to be achieved. Among the figures of merit for this type of concentrator, the directional intercept factor plays a major role and is defined as the ratio of the power of the collector to that at the entry aperture, in a lossless concentrator illuminated by light arriving from a given direction. A procedure for measuring outdoor, full size panels has been developed, and a correction method for avoiding the effect of unwanted diffuse radiation during the measurements is presented.

22.5% efficient silicon heterojunction solar cell with molybdenum oxide hole collector

DOE PAGES

Geissbühler, Jonas; Werner, Jérémie; Nicolas, Silvia Martin de; ...

2015-08-24

Substituting the doped amorphous silicon films at the front of silicon heterojunction solar cells with wide-bandgap transition metal oxides can mitigate parasitic light absorption losses. This was recently proven by replacing p-type amorphous silicon with molybdenum oxide films. In this article, we evidence that annealing above 130 °C—often needed for the curing of printed metal contacts—detrimentally impacts hole collection of such devices. Furthermore, we circumvent this issue by using electrodeposited copper front metallization and demonstrate a silicon heterojunction solar cell with molybdenum oxide hole collector, featuring a fill factor value higher than 80% and certified energy conversion efficiency of 22.5%.

First third filling parameters of left ventricle assessed from gated equilibrium studies in patients with various heart diseases

DOE Office of Scientific and Technical Information (OSTI.GOV)

Adatepe, M.H.; Nichols, K.; Powell, O.M.

1984-01-01

The authors determined the first third filling fraction (1/3 FF), the maximum filling rate (1/3 FR) and the mean filling rate (1/3 MFR) for the first third diastolic filling period of the left ventricle in patients with coronary artery disease (CAD), valvular heart disease (VHD), pericardial effusion (PE), cardiomyopathies (CM), chronic obstructive lung disease (COPD) and in 5 normals-all from resting gated equilibrium studies. Parameters are calculated from the third order Fourier fit to the LV volume curve and its derivative. 1/3 FF% = 1/3 diastolic count - end systolic count / 1/3 diastolic count x 100. Patients with CADmore » are divided into two groups: Group I with normal ejection fraction (EF) and wall motion (WM); Group II with abnormal EF and WM. Results are shown in the table. Abnormal filling parameters are found not only in CAD but in VHD, PE and CM. The authors conclude that the first third LV filling parameters are sensitive but non-specific indicators of filling abnormalities caused by diverse etiologic factors. Abnormal first third filling parameters may occur in the presence of a normal resting EF and WM in CAD.« less

Tailoring of physical properties in highly filled experimental nanohybrid resin composites.

PubMed

Pick, Bárbara; Pelka, Matthias; Belli, Renan; Braga, Roberto R; Lohbauer, Ulrich

2011-07-01

To assess the elastic modulus (EM), volumetric shrinkage (VS), and polymerization shrinkage stress (PSS) of experimental highly filled nanohybrid composites as a function of matrix composition, filler distribution, and density. One regular viscosity nanohybrid composite (Grandio, VOCO, Germany) and one flowable nanohybrid composite (Grandio Flow, VOCO) were tested as references along with six highly filled experimental nanohybrid composites (four Bis-GMA-based, one UDMA-based, and one Ormocer®-based). The experimental composites varied in filler size and density. EM values were obtained from the "three-point bending" load-displacement curve. VS was calculated with Archimedes' buoyancy principle. PSS was determined in 1-mm thick specimens placed between two (poly)methyl methacrylate rods (Ø=6mm) attached to an universal testing machine. Data were analyzed using oneway ANOVA, Tukey's test (α=0.05), and linear regression analyses. The flowable composite exhibited the highest VS and PSS but lowest EM. The PSS was significantly lower with Ormocer. The EM was significantly higher among experimental composites with highest filler levels. No significant differences were found between all other experimental composites regarding VS and PSS. Filler density and size did not influence EM, VS, or PSS. Neither the filler configuration nor matrix composition in the investigated materials significantly influenced composite shrinkage and mechanical properties. The highest filled experimental composite seemed to increase EM by keeping VS and PSS low; however, matrix composition seemed to be the determinant factor for shrinkage and stress development. The Ormocer, with reduced PSS, deserves further investigation. Filler size and density did not influence the tested parameters. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

CRYogenic Orbital TEstbed Ground Test Article Thermal Analysis

NASA Technical Reports Server (NTRS)

Piryk, David; Schallhorn, Paul; Walls, Laurie; Stopnitzky, Benny; Rhys, Noah; Wollen, Mark

2012-01-01

The purpose of this study was to anchor thermal and fluid system models to CRYOTE ground test data. The CRYOTE ground test artide was jointly developed by Innovative Engineering Solutions, United Launch Alliance and NASA KSC. The test article was constructed out of a titanium alloy tank, Sapphire 77 composite skin (similar to G10), an external secondary payload adapter ring, thermal vent system, multi layer insulation and various data acquisition instrumentation. In efforts to understand heat loads throughout this system, the GTA (filled with liquid nitrogen for safety purposes) was subjected to a series of tests in a vacuum chamber at Marshall Space Flight Center. By anchoring analytical models against test data, higher fidelity thermal environment predictions can be made for future flight articles which would eventually demonstrate critical cryogenic fluid management technologies such as system chilldown, transfer, pressure control and long term storage. Significant factors that influenced heat loads included radiative environments, multi-layer insulation performance, tank fill levels and pressures and even contact conductance coefficients. This report demonstrates how analytical thermal/fluid networks were established and includes supporting rationale for specific thermal responses.

A sub-atmospheric chemical vapor deposition process for deposition of oxide liner in high aspect ratio through silicon vias.

PubMed

Lisker, Marco; Marschmeyer, Steffen; Kaynak, Mehmet; Tekin, Ibrahim

2011-09-01

The formation of a Through Silicon Via (TSV) includes a deep Si trench etching and the formation of an insulating layer along the high-aspect-ratio trench and the filling of a conductive material into the via hole. The isolation of the filling conductor from the silicon substrate becomes more important for higher frequencies due to the high coupling of the signal to the silicon. The importance of the oxide thickness on the via wall isolation can be verified using electromagnetic field simulators. To satisfy the needs on the Silicon dioxide deposition, a sub-atmospheric chemical vapor deposition (SA-CVD) process has been developed to deposit an isolation oxide to the walls of deep silicon trenches. The technique provides excellent step coverage of the 100 microm depth silicon trenches with the high aspect ratio of 20 and more. The developed technique allows covering the deep silicon trenches by oxide and makes the high isolation of TSVs from silicon substrate feasible which is the key factor for the performance of TSVs for mm-wave 3D packaging.

Is Detrusor Contraction during Rapid Bladder Filling Caused by Cold or Warm Water? A Randomized, Controlled, Double-Blind Trial.

PubMed

Kozomara, Marko; Mehnert, Ulrich; Seifert, Burkhardt; Kessler, Thomas M

2018-01-01

We investigated whether detrusor contraction during rapid bladder filling is provoked by cold or warm water. Patients with neurogenic lower urinary tract dysfunction were included in this randomized, controlled, double-blind trial. At the end of a standard urodynamic investigation patients underwent 2 bladder fillings using a 4C ice water test or a 36C warm water test saline solution at a filling speed of 100 ml per minute. The order was randomly selected, and patients and investigators were blinded to the order. The primary outcome measure was detrusor overactivity, maximum detrusor pressure and maximum bladder filling volume during the ice and warm water tests. Nine women and 31 men were the subject of data analysis. Neurogenic lower urinary tract dysfunction was caused by spinal cord injury in 33 patients and by another neurological disorder in 7. Irrespective of test order detrusor overactivity occurred significantly more often during the ice water test than during the warm water test (30 of 40 patients or 75% vs 25 of 40 or 63%, p = 0.02). When comparing the ice water test to the warm water test, maximum detrusor pressure was significantly higher and maximum bladder filling volume was significantly lower during the ice water test (each p <0.001). The order of performing the tests (ice water first vs warm water first) had no effect on the parameters. Our findings imply that the more frequent detrusor overactivity, higher maximum detrusor pressure and lower bladder filling volume during the ice water test compared to the warm water test were caused by cold water. This underlies the theory of a C-fiber mediated bladder cooling reflex in humans. Copyright © 2018 American Urological Association Education and Research, Inc. Published by Elsevier Inc. All rights reserved.

Design of antibody-functionalized carbon nanotubes filled with radioactivable metals towards a targeted anticancer therapy

NASA Astrophysics Data System (ADS)

Spinato, Cinzia; Perez Ruiz de Garibay, Aritz; Kierkowicz, Magdalena; Pach, Elzbieta; Martincic, Markus; Klippstein, Rebecca; Bourgognon, Maxime; Wang, Julie Tzu-Wen; Ménard-Moyon, Cécilia; Al-Jamal, Khuloud T.; Ballesteros, Belén; Tobias, Gerard; Bianco, Alberto

2016-06-01

In the present work we have devised the synthesis of a novel promising carbon nanotube carrier for the targeted delivery of radioactivity, through a combination of endohedral and exohedral functionalization. Steam-purified single-walled carbon nanotubes (SWCNTs) have been initially filled with radioactive analogues (i.e. metal halides) and sealed by high temperature treatment, affording closed-ended CNTs with the filling material confined in the inner cavity. The external functionalization of these filled CNTs was then achieved by nitrene cycloaddition and followed by the derivatization with a monoclonal antibody (Cetuximab) targeting the epidermal growth factor receptor (EGFR), overexpressed by several cancer cells. The targeting efficiency of the so-obtained conjugate was evaluated by immunostaining with a secondary antibody and by incubation of the CNTs with EGFR positive cells (U87-EGFR+), followed by flow cytometry, confocal microscopy or elemental analyses. We demonstrated that our filled and functionalized CNTs can internalize more efficiently in EGFR positive cancer cells.In the present work we have devised the synthesis of a novel promising carbon nanotube carrier for the targeted delivery of radioactivity, through a combination of endohedral and exohedral functionalization. Steam-purified single-walled carbon nanotubes (SWCNTs) have been initially filled with radioactive analogues (i.e. metal halides) and sealed by high temperature treatment, affording closed-ended CNTs with the filling material confined in the inner cavity. The external functionalization of these filled CNTs was then achieved by nitrene cycloaddition and followed by the derivatization with a monoclonal antibody (Cetuximab) targeting the epidermal growth factor receptor (EGFR), overexpressed by several cancer cells. The targeting efficiency of the so-obtained conjugate was evaluated by immunostaining with a secondary antibody and by incubation of the CNTs with EGFR positive cells (U87-EGFR+), followed by flow cytometry, confocal microscopy or elemental analyses. We demonstrated that our filled and functionalized CNTs can internalize more efficiently in EGFR positive cancer cells. Electronic supplementary information (ESI) available. See DOI: 10.1039/c5nr07923c

Tablet, Web-Based, or Paper Questionnaires for Measuring Anxiety in Patients Suspected of Breast Cancer: Patients' Preferences and Quality of Collected Data

PubMed Central

Wessels, Hester; van Diest, Paul J; Pijnappel, Ruud M; Haaring, Cees; van der Pol, Carmen C; Witkamp, Arjen J; van den Bosch, Maurice A; Verkooijen, Helena M

2014-01-01

Background Electronic applications are increasingly being used in hospitals for numerous purposes. Objective Our aim was to assess differences in the characteristics of patients who choose paper versus electronic questionnaires and to evaluate the data quality of both approaches. Methods Between October 2012 and June 2013, 136 patients participated in a study on diagnosis-induced stress and anxiety. Patients were asked to fill out questionnaires at six different moments during the diagnostic phase. They were given the opportunity to fill out the questionnaires on paper or electronically (a combination of tablet and Web-based questionnaires). Demographic characteristics and completeness of returned data were compared between groups. Results Nearly two-thirds of patients (88/136, 64.7%) chose to fill out the questionnaires on paper, and just over a third (48/136, 35.3%) preferred the electronic option. Patients choosing electronic questionnaires were significantly younger (mean 47.3 years vs mean 53.5 in the paper group, P=.01) and higher educated (P=.004). There was significantly more missing information (ie, at least one question not answered) in the paper group during the diagnostic day compared to the electronic group (using a tablet) (28/88 vs 1/48, P<.001). However, in the week after the diagnostic day, missing information was significantly higher in the electronic group (Web-based questionnaires) compared to the paper group (41/48 vs 38/88, P<.001). Conclusions Younger patients and patients with a higher level of education have a preference towards filling out questionnaires electronically. In the hospital, a tablet is an excellent medium for patients to fill out questionnaires with very little missing information. However, for filling out questionnaires at home, paper questionnaires resulted in a better response than Web-based questionnaires. PMID:25364951

Intermittent Surface Water Connectivity: Fill and Spill vs. Fill ...

EPA Pesticide Factsheets

Intermittent surface connectivity can influence aquatic systems, since chemical and biotic movements are often associated with water flow. Although often referred to as fill and spill, wetlands also fill and merge. We examined the effects of these connection types on water levels, ion concentrations, and biotic communities of eight prairie pothole wetlands between 1979 and 2015. Fill and spill caused pulsed surface water connections that were limited to periods following spring snow melt. In contrast, two wetlands connected through fill and merge experienced a nearly continuous, 20-year surface water connection and had completely coincident water levels. Fill and spill led to minimal convergence in dissolved ions and macroinvertebrate composition, while these constituents converged under fill and merge. The primary factor determining difference in responses was duration of the surface water connection between wetland pairs. Our findings suggest that investigations into the effects of intermittent surface water connections should not consider these connections generically, but need to address the specific types of connections. In particular, fill and spill promotes external water exports while fill and merge favors internal storage. The behaviors of such intermittent connections will likely be accentuated under a future with more frequent and severe climate extremes. Under the Safe and Sustainable Water Resources National Program, work is being done to qu

Intermittent Surface Water Connectivity: Fill and Spill Vs. Fill ...

EPA Pesticide Factsheets

Intermittent surface connectivity can influence aquatic systems, since chemical and biotic movements are often associated with water flow. Although often referred to as fill and spill, wetlands also fill and merge. We examined the effects of these connection types on water levels, ion concentrations, and biotic communities of eight prairie pothole wetlands between 1979 and 2015. Fill and spill caused pulsed surface water connections that were limited to periods following spring snow melt. In contrast, two wetlands connected through fill and merge experienced a nearly continuous, 20-year surface water connection and had completely coincident water levels. Fill and spill led to minimal convergence in dissolved ions and macroinvertebrate composition, while these constituents converged under fill and merge. The primary factor determining difference in responses was duration of the surface water connection between wetland pairs. Our findings suggest that investigations into the effects of intermittent surface water connections should not consider these connections generically, but need to address the specific types of connections. In particular, fill and spill promotes external water exports while fill and merge favors internal storage. The behaviors of such intermittent connections will likely be accentuated under a future with more frequent and severe climate extremes. Under the Safe and Sustainable Water Resources National Program, work is being done to qu

Preparation and Imaging Investigation of Dual-targeted C3F8-filled PLGA Nanobubbles as a Novel Ultrasound Contrast Agent for Breast Cancer.

PubMed

Du, Jing; Li, Xiao-Yu; Hu, He; Xu, Li; Yang, Shi-Ping; Li, Feng-Hua

2018-03-01

Molecularly-targeted contrast enhanced ultrasound (US) imaging is a promising imaging strategy with large potential for improving diagnostic accuracy of conventional US imaging in breast cancer detection. Therefore, we constructed a novel dual-targeted nanosized US contrast agent (UCA) directed at both vascular endothelial growth factor receptor 2 (VEGFR2) and human epidermal growth factor receptor 2 (HER2) based on perfluoropropane (C 3 F 8 )-filled poly(lactic-co-glycolic acid) (PLGA) (NBs) for breast cancer detection. In vitro, single- or dual-targeted PLGA NBs showed high target specificities and better effects of target enhancement in VEGFR2 or HER2-positive cells. In vivo, US imaging signal in the murine breast cancer model was significantly higher (P < 0.01) for dual-targeted NBs than single-targeted and non-targeted NBs. Small animal fluorescence imaging further confirmed the special affinity of the dual-targeted nanosized contrast agent to both VEGFR2 and HER2. Immunofluorescence and immunohistochemistry staining confirmed the expressions of VEGFR2 and HER2 on tumor neovasculature and tumor cells of breast cancer. In conclusions, the feasibility of using dual-targeted PLGA NBs to enhance ultrasonic images is demonstrated in vitro and in vivo. This may be a promising approach to target biomarkers of breast cancer for two site-specific US molecular imaging.

Photoelectrochemical Cell of Hybrid Regioregular POLY(3-HEXYLTHIOPHENE-2,5-DIYL) and Molybdenum Disulfide Film

NASA Astrophysics Data System (ADS)

Abdelmola, Fatmaelzahraa M.; Ram, Manoj K.; Takshi, Arash; Stafanakos, Elias; Kumar, Ashok; Goswami, D. Yogi

The photoelectrochemical cell attracts attention worldwide due to conversion of optical energy into electricity, production of hydrogen through water splitting and use in photodetector and photo-sensor applications. We have been working on the photochemical cell based on regioregular polyhexylthiophenes hybrid-structured films for photoelectrochemical and photovoltaic applications. This paper discusses the hybrid film studies on regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT) with 2D molybdenum disulfide (MoS2) for photoelectrochemical cell. The hybrid P3HT/MoS2 films deposited over indium tin oxide (ITO)-coated glass plate or n-type silicon substrates were characterized using FTIR, UV/vis, electrochemical and scanning electron microscopy (SEM) techniques. The optical measurements showed a higher absorption magnitude with low reflection properties of P3HT/MoS2 hybrid films revealing a superior photocurrent compared to both P3HT and MoS2 films. The P3HT/MoS2 hybrid-based photoelectrochemical cell yielded a short-circuit current (Isc) of 183.16μAṡcm-2, open-circuit voltage (Voc) of 0.92V, fill factor (FF) of 25% and power conversion efficiency (η) of 0.18% under the light intensity of 242Wṡm-2. The estimated power conversion efficiency and fill factor are comparable to organic-based photovoltaic devices.

Dye-sensitized solar cell characteristics of nanocomposite zinc ferrite working electrode: effect of composite precursors and titania as a blocking layer on photovoltaic performance.

PubMed

Habibi, Mohammad Hossein; Habibi, Amir Hossein; Zendehdel, Mahmoud; Habibi, Mehdi

2013-06-01

This research investigates the performance of a zinc ferrite (ZF) as working electrodes in a dye-sensitized solar cell (DSSC). This ZF working electrode was prepared by sol-gel and thermal decomposition of four different precursors including: zinc acetate dihydrate (Zn(CH3COO)2·2H2O), ferric nitrate nonahydrate (Fe(NO3)3·9H2O), iron(III) acetate; Fe(C2H3O2)3, and zinc nitrate hexahydrate, Zn(NO3)2·6H2O. The effects of annealing temperature and precursors on the structural, morphological, and optical properties were investigated. The field emission scanning electron microscope images (FESEM) and scanning electron microscopy (SEM) show that ZFe films are polycrystalline in nature and homogeneous with densely packed grains. Nanoporous zinc ferrite coatings were prepared by doctor blade technique on the fluorine-doped tin oxide (FTO) and used as working electrodes in DSSC. In all DSSCs, platinized FTO and [Co(bpy)3](2+/3+) in 3-methoxy proponitrile were used as counter electrode and redox mediator system respectively. Comparing the fill factors of four different zinc ferrite nanocomposites, the highest fill factor was for ZnFe2O4-TBL sample. Cell fabricated with ZnFeA working electrode shows relatively higher Jsc. Copyright © 2013 Elsevier B.V. All rights reserved.

Treatment of domestic wastewater by subsurface flow constructed wetlands filled with gravel and tire chip media.

PubMed

Richter, A Y; Weaver, R W

2003-12-01

Subsurface flow constructed wetlands (SFCWs) are becoming increasingly common in on-site treatment of wastewater. Gravel is the most popular form of wetland fill medium, but tire chips provide more porosity, are less dense, and less expensive. This study determines the treatment efficiency of SFCWs filled with gravel or tire chip media to treat domestic wastewater. The influent and effluent of six SFCWs filled with tire chip medium and six SFCWs filled with gravel were monitored for 5 to 16 consecutive months. Parameters measured included pH, biochemical oxygen demand (BOD5), total and volatile suspended solids, NH4, P, and fecal and total coliforms. The only clear difference between medium types in wetland performance was for P. Soluble P in the effluent averaged 1.6 +/- 1.0 mg l(-1) in the tire chip-filled wetlands and 4.8 +/- 3.2 mg l(-1) in the gravel-filled wetlands. Most likely, Fe from exposed wires in shredded steel-belted tires complexed with P to create an insoluble compound. Tire chips may be a better fill medium for SFCWs than gravel because of higher porosity, lower cost, and greater reduction of P in effluent.

Diagnostic accuracy of different display types in detection of recurrent caries under restorations by using CBCT.

PubMed

Baltacıoĝlu, İsmail H; Eren, Hakan; Yavuz, Yasemin; Kamburoğlu, Kıvanç

To assess the in vitro diagnostic ability of CBCT images using seven different display types in the detection of recurrent caries. Our study comprised 128 extracted human premolar and molar teeth. 8 groups each containing 16 teeth were obtained as follows: (1) Black Class I (Occlusal) amalgam filling without caries; (2) Black Class I (Occlusal) composite filling without caries; (3) Black Class II (Proximal) amalgam filling without caries; (4) Black Class II (Proximal) composite filling without caries; (5) Black Class I (Occlusal) amalgam filling with caries; (6) Black Class I (Occlusal) composite filling with caries; (7) Black Class II (Proximal) amalgam filling with caries; and (8) Black Class II (Proximal) composite filling with caries. Teeth were imaged using 100 × 90 mm field of view at three different voxel sizes of a CBCT unit (Planmeca ProMax(®) 3D ProFace™; Planmeca, Helsinki, Finland). CBCT TIFF images were opened and viewed using custom-designed software for computers on different display types. Intra- and interobserver agreements were calculated. The highest area under the receiver operating characteristic curve (Az) values for each image type, observer, reading and restoration were compared using z-tests against Az = 0.5. The significance level was set at p = 0.05. We found poor and moderate agreements. In general, Az values were found when software and medical diagnostic monitor were utilized. For Observer 2, Az values were statistically significantly higher when software was used on medical monitor [p = 0.036, p = 0.015 and p = 0.002, for normal-resolution mode (0.200 mm(3) voxel size), high-resolution mode (0.150 mm(3) voxel size) and low-resolution mode (0.400 mm(3) voxel size), respectively]. No statistically significant differences were found among other display types for all modes (p > 0.05). In general, no difference was found among 3 different voxel sizes (p > 0.05). In general, higher Az values were obtained for composite restorations than for amalgam restorations for all observers. For Observer 1, Az values for composite restorations were statistically significantly higher than those of amalgam restorations for MacBook and iPhone (Apple Inc., Cupertino, CA) assessments (p = 0.002 and p = 0.048, respectively). Higher Az values were observed with medical monitors when used with dedicated software compared to other display types which performed similarly in the diagnosis of recurrent caries under restorations. In addition, observers performed better in detection of recurrent caries when assessing composite restorations than amalgams.

Diagnostic accuracy of different display types in detection of recurrent caries under restorations by using CBCT

PubMed Central

Baltacıoĝlu, İsmail H; Eren, Hakan; Yavuz, Yasemin

2016-01-01

Objectives: To assess the in vitro diagnostic ability of CBCT images using seven different display types in the detection of recurrent caries. Methods: Our study comprised 128 extracted human premolar and molar teeth. 8 groups each containing 16 teeth were obtained as follows: (1) Black Class I (Occlusal) amalgam filling without caries; (2) Black Class I (Occlusal) composite filling without caries; (3) Black Class II (Proximal) amalgam filling without caries; (4) Black Class II (Proximal) composite filling without caries; (5) Black Class I (Occlusal) amalgam filling with caries; (6) Black Class I (Occlusal) composite filling with caries; (7) Black Class II (Proximal) amalgam filling with caries; and (8) Black Class II (Proximal) composite filling with caries. Teeth were imaged using 100 × 90 mm field of view at three different voxel sizes of a CBCT unit (Planmeca ProMax® 3D ProFace™; Planmeca, Helsinki, Finland). CBCT TIFF images were opened and viewed using custom-designed software for computers on different display types. Intra- and interobserver agreements were calculated. The highest area under the receiver operating characteristic curve (Az) values for each image type, observer, reading and restoration were compared using z-tests against Az = 0.5. The significance level was set at p = 0.05. Results: We found poor and moderate agreements. In general, Az values were found when software and medical diagnostic monitor were utilized. For Observer 2, Az values were statistically significantly higher when software was used on medical monitor [p = 0.036, p = 0.015 and p = 0.002, for normal-resolution mode (0.200 mm3 voxel size), high-resolution mode (0.150 mm3 voxel size) and low-resolution mode (0.400 mm3 voxel size), respectively]. No statistically significant differences were found among other display types for all modes (p > 0.05). In general, no difference was found among 3 different voxel sizes (p > 0.05). In general, higher Az values were obtained for composite restorations than for amalgam restorations for all observers. For Observer 1, Az values for composite restorations were statistically significantly higher than those of amalgam restorations for MacBook and iPhone (Apple Inc., Cupertino, CA) assessments (p = 0.002 and p = 0.048, respectively). Conclusions: Higher Az values were observed with medical monitors when used with dedicated software compared to other display types which performed similarly in the diagnosis of recurrent caries under restorations. In addition, observers performed better in detection of recurrent caries when assessing composite restorations than amalgams. PMID:27319604

A comparison of the hourly output between the Ambu® Smart-Infuser™ Pain Pump and the On-Q Pump® with Select-A-Flow™ Variable Rate Controller with standard and overfill volumes.

PubMed

Iliev, Peter; Bhalla, Tarun; Tobias, Joseph D

2016-04-01

The Ambu Smart-Infuser Pain Pump and the On-Q Pump with Select-a-Flow Variable Rate Controller are elastomeric devices with a flow regulator that controls the rate of infusion of a local anesthetic agent through a peripheral catheter. As a safety evaluation, we evaluated the infusion characteristics of these two devices when filled with manufacturer recommended standard volumes and when overfilled with a volume 50% in excess of that which is recommended. Nineteen disposable devices from the two manufacturers were used in this study. Nine were filled with 0.9% normal saline according to the respective manufacturers' recommendations (four Ambu pumps were filled with 650 ml and five On-Q pumps were filled with 550 ml) and 10 devices were 150% overfilled (five Ambu pumps were filled with 975 ml and five On-Q pumps were filled with 825 ml). All of the devices were set to infuse at 10 ml · h(-1) at room temperature (21°C) for 12 h. The fluid delivered during each 2-h period was measured using a graduated column. The On-Q pump (in the settings of normal fill and 150% overfill) delivered a significantly higher output per hour than the set rate during the first 8 h, while the Ambu pump delivered a value close to the set rate of 10 ml · h(-1). No significant difference in the hourly delivered output was noted for either device when comparing the normal fill to the 150% overfill groups. This investigation demonstrates that no change in the hourly output occurs with overfilling of these home infusion devices. However, as noted previously, the hourly output from the On-Q device is significantly higher than the set rate during the initial 8 h of infusion which could have potential clinical implications. © 2016 John Wiley & Sons Ltd.

The Roles of Family and Teacher Support in Moderating and Mediating Externalized and Internalized Outcomes of Exposure to Community Violence Among Arab and Jewish Adolescents in Israel.

PubMed

Haj-Yahia, Muhammad M; Leshem, Becky; Guterman, Neil B

2018-02-01

The study examined family and teacher support as factors that can protect adolescents from internalized and externalized problems after exposure to community violence (ECV). Self-administered questionnaires were filled out by a sample of 1,832 Arab and Jewish Israeli high school students. The Arab adolescents reported significantly higher levels of community violence victimization, internalized problems, externalized problems, family support, and teacher support than the Jewish adolescents. The girls reported higher levels of internalized problems, and the boys reported higher levels of externalized problems. ECV predicted high levels of internalized and externalized problems, family support predicted low levels of internalized and externalized problems, and teacher support had no predictive role. Path analysis confirmed the significance of the relationships between ECV effects, support variables, and gender. The limitations of the study and implications of the findings for future research and for the development of family care and family intervention programs are discussed.

N : P stoichiometry in a forested runoff during storm events: comparisons with regions and vegetation types.

PubMed

Guo, Lanlan; Chen, Yi; Zhang, Zhao; Fukushima, Takehiko

2012-01-01

Nitrogen and phosphorus are considered the most important limiting elements in terrestrial and aquatic ecosystems. however, very few studies have focused on which is from forested streams, a bridge between these two systems. To fill this gap, we examined the concentrations of dissolved N and P in storm waters from forested watersheds of five regions in Japan, to characterize nutrient limitation and its potential controlling factors. First, dissolved N and P concentrations and the N : P ratio on forested streams were higher during storm events relative to baseflow conditions. Second, significantly higher dissolved inorganic N concentrations were found in storm waters from evergreen coniferous forest streams than those from deciduous broadleaf forest streams in Aichi, Kochi, Mie, Nagano, and with the exception of Tokyo. Finally, almost all the N : P ratios in the storm water were generally higher than 34, implying that the storm water should be P-limited, especially for Tokyo.

N : P Stoichiometry in a Forested Runoff during Storm Events: Comparisons with Regions and Vegetation Types

PubMed Central

Guo, Lanlan; Chen, Yi; Zhang, Zhao; Fukushima, Takehiko

2012-01-01

Nitrogen and phosphorus are considered the most important limiting elements in terrestrial and aquatic ecosystems. however, very few studies have focused on which is from forested streams, a bridge between these two systems. To fill this gap, we examined the concentrations of dissolved N and P in storm waters from forested watersheds of five regions in Japan, to characterize nutrient limitation and its potential controlling factors. First, dissolved N and P concentrations and the N : P ratio on forested streams were higher during storm events relative to baseflow conditions. Second, significantly higher dissolved inorganic N concentrations were found in storm waters from evergreen coniferous forest streams than those from deciduous broadleaf forest streams in Aichi, Kochi, Mie, Nagano, and with the exception of Tokyo. Finally, almost all the N : P ratios in the storm water were generally higher than 34, implying that the storm water should be P-limited, especially for Tokyo. PMID:22547978

Determinants of immediate price impacts at the trade level in an emerging order-driven market

NASA Astrophysics Data System (ADS)

Zhou, Wei-Xing

2012-02-01

Common wisdom argues that, in general, large trades cause large price changes, whereas small trades cause small price changes. However, for extremely large price changes, the trade size and news play a minor role, while liquidity (especially price gaps on the limit order book) is a more influential factor. Hence, there might be other factors influencing the immediate price impacts of trades. In this paper, through mechanical analysis of price variations before and after a trade of arbitrary size, we identify that the trade size, the bid-ask spread, the price gaps and the outstanding volumes at the bid and ask sides of the limit order book have an impact on the changes in prices. We propose two regression models to investigate the influence of these microscopic factors on the price impact of buyer-initiated partially filled trades, seller-initiated partially filled trades, buyer-initiated filled trades and seller-initiated filled trades. We find that they have quantitatively similar explanatory powers and these factors can account for up to 44% of the price impacts. Large trade sizes, wide bid-ask spreads, high liquidity at the same side and low liquidity at the opposite side will cause a large price impact. We also find that the liquidity at the opposite side has a more influential impact than the liquidity at the same side. Our results shed new light on the determinants of immediate price impacts.

Dental caries increments and related factors in children with type 1 diabetes mellitus.

PubMed

Siudikiene, J; Machiulskiene, V; Nyvad, B; Tenovuo, J; Nedzelskiene, I

2008-01-01

The aim of this study was to analyse possible associations between caries increments and selected caries determinants in children with type 1 diabetes mellitus and their age- and sex-matched non-diabetic controls, over 2 years. A total of 63 (10-15 years old) diabetic and non-diabetic pairs were examined for dental caries, oral hygiene and salivary factors. Salivary flow rates, buffer effect, concentrations of mutans streptococci, lactobacilli, yeasts, total IgA and IgG, protein, albumin, amylase and glucose were analysed. Means of 2-year decayed/missing/filled surface (DMFS) increments were similar in diabetics and their controls. Over the study period, both unstimulated and stimulated salivary flow rates remained significantly lower in diabetic children compared to controls. No differences were observed in the counts of lactobacilli, mutans streptococci or yeast growth during follow-up, whereas salivary IgA, protein and glucose concentrations were higher in diabetics than in controls throughout the 2-year period. Multivariable linear regression analysis showed that children with higher 2-year DMFS increments were older at baseline and had higher salivary glucose concentrations than children with lower 2-year DMFS increments. Likewise, higher 2-year DMFS increments in diabetics versus controls were associated with greater increments in salivary glucose concentrations in diabetics. Higher increments in active caries lesions in diabetics versus controls were associated with greater increments of dental plaque and greater increments of salivary albumin. Our results suggest that, in addition to dental plaque as a common caries risk factor, diabetes-induced changes in salivary glucose and albumin concentrations are indicative of caries development among diabetics. Copyright 2008 S. Karger AG, Basel.

Measurement of funny current (I(f)) channel mRNA in human atrial tissue: correlation with left atrial filling pressure and atrial fibrillation.

PubMed

Lai, L P; Su, M J; Lin, J L; Tsai, C H; Lin, F Y; Chen, Y S; Hwang, J J; Huang, S K; Tseng, Y Z; Lien, W P

1999-07-01

The funny current (I(f)) contributes to phase IV spontaneous depolarization in cardiac pacemaker tissue. Enhanced I(f) activity in myocardial tissue may lead to increased automaticity and therefore tachyarrhythmia. We measured the amount of I(f) activity in the messenger ribonucleic acid (mRNA) in human atrial tissue and correlated the mRNA amount to left atrial filling pressure and atrial fibrillation (AF). A total of 34 patients undergoing open heart surgery were included (15 men and 19 women, aged 55+/-10 years). Atrial tissue was obtained from the right atrial free wall, the right atrial appendage, the left atrial free wall, and the left atrial appendage, respectively. The mRNA amount of the I(f) channel was measured by reverse transcription polymerase chain reaction and was normalized to the mRNA levels of glyceraldehyde 3-phosphate dehydrogenase. We found that the I(f) channel mRNA was present at all the atrial sampling sites. A higher left atrial filling pressure, an indicator of congestive heart failure, was associated with a higher I(f) mRNA level (r2 = 0.446, P < 0.01 by linear regression). We also found that the mRNA amount was significantly higher in patients with AF than in patients without AF (1.68+/-0.49 vs 1.27+/-0.43; P < 0.05). Age, sex, right atrial filling pressure, left atrial dimension, and left ventricular ejection fraction had no significant effect on the mRNA level. The mRNA of the I(f) channel is present in the free-wall area and appendage area from both atria. Increased left atrial filling pressure and clinical AF are associated with increased I(f) mRNA level.

Burnout and Associated Factors among Iranian Emergency Medicine Practitioners.

PubMed

Jalili, Mohammad; Sadeghipour Roodsari, Gholamreza; Bassir Nia, Anahita

2013-09-01

Emergency physicians are at risk of burnout, which can affect their mental health, as well as patient care. We assessed burnout level among Iranian emergency physicians and investigated demographic, work-related factors and stressors associated with higher burnout. In a cross-sectional study, we surveyed all 188 emergency medicine residents and practitioners in Iran. We measured burnout using 22-item Maslach Burnout Inventory assessing emotional exhaustion, depersonalization and personal accomplishment, also demographic factors, work related factors and sources of stress in emergency department using anonymous self-administered questionnaire. Descriptive analysis, univariate analysis to evaluate association with higher score of burnout, and multivariate logistic regression analysis to predict high burnout in 3 subscales was performed. Totally, 165 questionnaires were filled (response rate: 88%; mean age: 33.6 years, 91% male). Mean burnout scores were 22.94 for emotional exhaustion (95% CI=20.78-25.01; moderate), 9.3 for depersonalization (95% CI=8.24-10.36; moderate to high), and 31.47 for personal accomplishment (95% CI=29.87-33.07; moderate to high). Frequent reported sources of stress were shortage of equipment, problem with work physical environment, and relationship with other services. All 19 sources of stress were associated with higher score of emotional exhaustion and depersonalization; while twelve out of 19 were significantly associated with lower level of personal accomplishment. In logistic regression model, the significant predictors for high emotional exhaustion were work overload, feeling of insecurity for future career and difficulties to balance professional and private life. Burnout is high among Iranian emergency medicine practitioners and some interventions can be proposed to reduce stress.

Experimental study on heat transfer enhancement of laminar ferrofluid flow in horizontal tube partially filled porous media under fixed parallel magnet bars

NASA Astrophysics Data System (ADS)

Sheikhnejad, Yahya; Hosseini, Reza; Saffar Avval, Majid

2017-02-01

In this study, steady state laminar ferroconvection through circular horizontal tube partially filled with porous media under constant heat flux is experimentally investigated. Transverse magnetic fields were applied on ferrofluid flow by two fixed parallel magnet bar positioned on a certain distance from beginning of the test section. The results show promising notable enhancement in heat transfer as a consequence of partially filled porous media and magnetic field, up to 2.2 and 1.4 fold enhancement were observed in heat transfer coefficient respectively. It was found that presence of both porous media and magnetic field simultaneously can highly improve heat transfer up to 2.4 fold. Porous media of course plays a major role in this configuration. Virtually, application of Magnetic field and porous media also insert higher pressure loss along the pipe which again porous media contribution is higher that magnetic field.

Ionic liquid gating reveals trap-filled limit mobility in low temperature amorphous zinc oxide

NASA Astrophysics Data System (ADS)

Bubel, S.; Meyer, S.; Kunze, F.; Chabinyc, M. L.

2013-10-01

In low-temperature solution processed amorphous zinc oxide (a-ZnO) thin films, we show the thin film transistor (TFT) characteristics for the trap-filled limit (TFL), when the quasi Fermi energy exceeds the conduction band edge and all tail-states are filled. In order to apply gate fields that are high enough to reach the TFL, we use an ionic liquid tape gate. Performing capacitance voltage measurements to determine the accumulated charge during TFT operation, we find the TFL at biases higher than predicted by the electronic structure of crystalline ZnO. We conclude that the density of states in the conduction band of a-ZnO is higher than in its crystalline state. Furthermore, we find no indication of percolative transport in the conduction band but trap assisted transport in the tail-states of the band.

Performance enhancement of perovskite solar cells with Mg-doped TiO{sub 2} compact film as the hole-blocking layer

DOE Office of Scientific and Technical Information (OSTI.GOV)

Wang, Jing; Qin, Minchao; Tao, Hong

2015-03-23

In this letter, we report perovskite solar cells with thin dense Mg-doped TiO{sub 2} as hole-blocking layers (HBLs), which outperform cells using TiO{sub 2} HBLs in several ways: higher open-circuit voltage (V{sub oc}) (1.08 V), power conversion efficiency (12.28%), short-circuit current, and fill factor. These properties improvements are attributed to the better properties of Mg-modulated TiO{sub 2} as compared to TiO{sub 2} such as better optical transmission properties, upshifted conduction band minimum (CBM) and downshifted valence band maximum (VBM), better hole-blocking effect, and higher electron life time. The higher-lying CBM due to the modulation with wider band gap MgO and themore » formation of magnesium oxide and magnesium hydroxides together resulted in an increment of V{sub oc}. In addition, the Mg-modulated TiO{sub 2} with lower VBM played a better role in the hole-blocking. The HBL with modulated band position provided better electron transport and hole blocking effects within the device.« less

Investigation of Grating-Assisted Trimodal Interferometer Biosensors Based on a Polymer Platform.

PubMed

Liang, Yuxin; Zhao, Mingshan; Wu, Zhenlin; Morthier, Geert

2018-05-10

A grating-assisted trimodal interferometer biosensor is proposed and numerically analyzed. A long period grating coupler, for adjusting the power between the fundamental mode and the second higher order mode, is investigated, and is shown to act as a conventional directional coupler for adjusting the power between the two arms. The trimodal interferometer can achieve maximal fringe visibility when the powers of the two modes are adjusted to the same value by the grating coupler, which means that a better limit of detection can be expected. In addition, the second higher order mode typically has a larger evanescent tail than the first higher order mode in bimodal interferometers, resulting in a higher sensitivity of the trimodal interferometer. The influence of fabrication tolerances on the performance of the designed interferometer is also investigated. The power difference between the two modes shows inertia to the fill factor of the grating, but high sensitivity to the modulation depth. Finally, a 2050 2π/RIU (refractive index unit) sensitivity and 43 dB extinction ratio of the output power are achieved.

Management of Mastectomy Skin Necrosis in Implant Based Breast Reconstruction.

PubMed

Sue, Gloria R; Long, Chao; Lee, Gordon K

2017-05-01

Mastectomy skin necrosis is a significant problem after breast reconstruction. This complication may lead to poor wound healing and need for implant removal, which may delay subsequent oncologic treatment. We sought to characterize factors associated with mastectomy skin necrosis and propose a management algorithm. A retrospective review was performed on consecutive patients undergoing implant-based breast reconstruction by the senior author from 2006 through 2015. Patient-level factors including age, race, body mass index, history of hypertension, history of diabetes, history of smoking, and history of radiation were collected. Surgical factors including type of mastectomy, location of implant placement, and immediate versus delayed reconstruction were collected. The incidence and treatment of mastectomy skin necrosis were analyzed. A total of 293 patients underwent either unilateral or bilateral implant-based breast reconstructions after mastectomy with a total of 471 reconstructed breasts. Mastectomy skin necrosis was observed in 8.1% of reconstructed breasts. Skin necrosis was not associated with age, hypertension, diabetes, prior radiation, or type of mastectomy. The incidence of skin necrosis was higher among smokers (17.9% vs 5.0%, P < 0.001), among patients with higher body mass index (11.4% vs 6.1%, P = 0.05), patients who underwent immediate reconstruction compared to delayed (9.6% vs 0%, P = 0.004), placement of expander under acellular dermal matrix compared with submuscular placement (12.0% vs 5.2%, P = 0.02), and use of higher initial expander fill volume compared with lower fill volume (11.4% vs 5.4%, P = 0.02).The median necrosis size was 8 cm. The median time to treatment was 15 days postoperatively. In 55% of patients minor necrosis was treated with clinic debridement, whereas 43% had larger areas of necrosis requiring operative debridement. The median size treated with clinic debridement was 5.5 cm, compared to 15 cm for operative debridement. All necrosis was treated in a timely fashion and did not delay adjuvant therapy. Mastectomy skin necrosis occurred in 8.1% of breasts after implant-based reconstruction. Necrosis less than 10 cm can be treated successfully with local debridement in the clinic setting. Timely and appropriate treatment of skin necrosis with debridement and primary closure expedites wound healing and facilitates tissue expander breast reconstruction.

Spectroscopic and Mechanical Properties of a New Generation of Bulk Fill Composites

PubMed Central

Monterubbianesi, Riccardo; Orsini, Giovanna; Tosi, Giorgio; Conti, Carla; Librando, Vito; Procaccini, Maurizio; Putignano, Angelo

2016-01-01

Objectives: The aims of this study were to in vitro evaluate the degree of conversion and the microhardness properties of five bulk fill resin composites; in addition, the performance of two curing lamps, used for composites polymerization, was also analyzed. Materials and Methods: The following five resin-based bulk fill composites were tested: SureFil SDR®, Fill Up!™, Filtek™, SonicFill™, and SonicFill2™. Samples of 4 mm in thickness were prepared using Teflon molds filled in one increment and light-polymerized using two LED power units. Ten samples for each composite were cured using Elipar S10 and 10 using Demi Ultra. Additional samples of SonicFill2, (3 and 5 mm-thick) were also tested. The degree of conversion (DC) was determined by Raman spectroscopy, while the Vickers microhardness (VMH) was evaluated using a microhardness tester. The experimental evaluation was carried out on top and bottom sides, immediately after curing (t0), and, on bottom, after 24 h (t24). Two-ways analysis of variance was applied to evaluate DC and VMH-values. In all analyses, the level of significance was set at p < 0.05. Results: All bulk fill resin composites recorded satisfactory DCs on top and bottom sides. At t0, the top of SDR and SonicFill2 showed the highest DCs-values (85.56 ± 9.52 and 85.47 ± 1.90, respectively), when cured using Elipar S10; using Demi Ultra, SonicFill2 showed the highest DCs-values (90.53 ± 2.18). At t0, the highest DCs-values of bottom sides were recorded by SDR (84.64 ± 11.68), when cured using Elipar S10, and Filtek (81.52 ± 4.14), using Demi Ultra. On top sides, Demi Ultra lamp showed significant higher DCs compared to the Elipar S10 (p < 0.05). SonicFill2 reached suitable DCs also on bottom of 5 mm-thick samples. At t0, VMH-values ranged between 24.4 and 69.18 for Elipar S10, and between 26.5 and 67.3 for Demi Ultra. Using both lamps, the lowest VMH-values were shown by SDR, while the highest values by SonicFill2. At t24, all DC and VMH values significantly increased. Conclusions: Differences in DC and VMH among materials are suggested to be material and curing lamp dependent. Even at t0, the three high viscosity bulk composites showed higher VMH than the flowable or dual curing composites. PMID:28082918

Spectroscopic and Mechanical Properties of a New Generation of Bulk Fill Composites.

PubMed

Monterubbianesi, Riccardo; Orsini, Giovanna; Tosi, Giorgio; Conti, Carla; Librando, Vito; Procaccini, Maurizio; Putignano, Angelo

2016-01-01

Objectives: The aims of this study were to in vitro evaluate the degree of conversion and the microhardness properties of five bulk fill resin composites; in addition, the performance of two curing lamps, used for composites polymerization, was also analyzed. Materials and Methods: The following five resin-based bulk fill composites were tested: SureFil SDR®, Fill Up!™, Filtek™, SonicFill™, and SonicFill2™. Samples of 4 mm in thickness were prepared using Teflon molds filled in one increment and light-polymerized using two LED power units. Ten samples for each composite were cured using Elipar S10 and 10 using Demi Ultra. Additional samples of SonicFill2, (3 and 5 mm-thick) were also tested. The degree of conversion (DC) was determined by Raman spectroscopy, while the Vickers microhardness (VMH) was evaluated using a microhardness tester. The experimental evaluation was carried out on top and bottom sides, immediately after curing (t0), and, on bottom, after 24 h (t24). Two-ways analysis of variance was applied to evaluate DC and VMH-values. In all analyses, the level of significance was set at p < 0.05. Results: All bulk fill resin composites recorded satisfactory DCs on top and bottom sides. At t0, the top of SDR and SonicFill2 showed the highest DCs-values (85.56 ± 9.52 and 85.47 ± 1.90, respectively), when cured using Elipar S10; using Demi Ultra, SonicFill2 showed the highest DCs-values (90.53 ± 2.18). At t0, the highest DCs-values of bottom sides were recorded by SDR (84.64 ± 11.68), when cured using Elipar S10, and Filtek (81.52 ± 4.14), using Demi Ultra. On top sides, Demi Ultra lamp showed significant higher DCs compared to the Elipar S10 ( p < 0.05). SonicFill2 reached suitable DCs also on bottom of 5 mm-thick samples. At t0, VMH-values ranged between 24.4 and 69.18 for Elipar S10, and between 26.5 and 67.3 for Demi Ultra. Using both lamps, the lowest VMH-values were shown by SDR, while the highest values by SonicFill2. At t24, all DC and VMH values significantly increased. Conclusions: Differences in DC and VMH among materials are suggested to be material and curing lamp dependent. Even at t0, the three high viscosity bulk composites showed higher VMH than the flowable or dual curing composites.

[Study on the detection rate and risk factors regarding non-suicidal self-injurious behavior in middle school students].

PubMed

Yan, Jing; Zhu, Cui-zhen; Situ, Ming-jing; DU, Na; Huang, Yi

2012-01-01

To understand the prevalence and risk factors of non-suicidal self-injury in middle school students. 1312 middle school students of Pengzhou and Santai were selected to fill in a Risky Behavior Questionnaire for Adolescence (RBQ-A), Family Environment Scale (FES), Center for Epidemiological Survey, Depression Scale (CES-D), Adolescent Self-Rating Life Events Check List (ASLEC), Social Support Scale for Adolescents (SSSA) and self-administered questionnaire. In all the research subjects, 1288 were qualified for the study in April 2011 before the risk factors for non-suicidal self-injury were identified by logistic regression. In 1288 middle school students, 22.67% had a history of non-suicidal self-injury, with 22.70% in boys and 22.64% in girls. 63.36% of students had injured themselves through variously ways, more seen in boys (26.88%) than in girls (11.36%) who cut or burnt themselves. The scores of ASLEC and CES-D in non-suicidal self-injury group appeared higher than that in the control group and the score of SSSA was found higher in the control group. The main risk factors for non-suicidal self-injuries were family conflict, depressive emotion, negative life events and receiving less social support. The prevalence of non-suicidal self-injury among middle school students in Pengzhou was high, which called for more attention.

Characterization and bake stability of dry fruit fillings in dehydrated chiku (Manilkara zapota L. P. Royen) incorporated biscuits.

PubMed

Aditi, Mahapatra; Shashirekha, M N; Sudha, M L

2017-06-01

Expanding the range of bakery products in terms of producing supplemented or dietetic products has been an increasingly important trend in contemporary baking. Value added products, especially products rich in fiber and phytochemicals are getting popular. Among the dry fruits used for filling, Figs were rich in ash and protein and Dates were rich in dietary fiber. Gallic acid was the dominant free phenolic acid in Fig whereas chlorogenic acid and procatechuic acid were dominant in Dates in the bound form. Farinograph water absorption, dough development time, maximum pressure (P), and extensibility (L) decreased on increase in the replacement of wheat flour with chiku powder from 0 to 30%. The dry fruit fillings in the pH range of 3.3-3.5 with 75-80°Bx showed better bake stability with respect to spreadability and breaking strength. Biscuits topped with higher °Bx fillings had higher breaking strength values even during storage. Among the gelling agents used, addition of sodium alginate stabilized and further improved the bake stability of the fillings. The chiku incorporated biscuits sandwiched with fruit filling were rich in dietary fiber. Also significant amounts of gallic acid and chlorogenic acid in free and bound form were present in the biscuit. Bakery products can act as a vehicle for supplementation of vitamins, minerals, protein, dietary fiber, and so on, to prevent nutritive deficiencies. Among the bakery products, biscuits are shelf stable and have better consumer acceptability by all age groups. To incorporate fruits which are rich in many bioactive principles, and to add on to variety, fruit sandwiched biscuits with fruit powder in the casing too. Fillings mainly from dry fruits were prepared at varying degree brix and with different gelling agents. Biscuit sheets containing chiku powder in the formulation was topped with the fillings and looked for the bake stability with respect to texture and spreadability. Addition of fruit powder in the shells and fruit filling in between helped to increase the nutritional characteristics of the product. © 2016 Wiley Periodicals, Inc.

Role of edge superconducting states in trapping of multi-quanta vortices by microholes. Application of the bitter decoration technique

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bezryadin, A.; Pannetier, B.

1996-01-01

The Bitter decoration technique is used to study the trapping of single and multiple quanta vortices by a lattice of circular microholes. By keeping a thin superconducting layer (the bottom) inside each hole the authors are able to visualise the trapped vortices. From this they determine, for the first time, the filling factor FF, i.e. the number of vortices captured inside a hole. In all cases the sample is cooled at a constant field before making the decoration. Two qualitatively different states of the vortex crystal are observed: (1) In case when the interhole distance is much larger than themore » coherence length, the filling factor averaged over many identical holes () is a stepwise function of the magnetic flux (of the external field) through the hole, because each hole captures the same number of vortices. The density of fluxoids inside the openings is higher than in the uniform film, but much lower than it should be in the state of equilibrium. The authors claim that the number of trapped vortices is determined by the edge superconducting states which appear around each hole at the modified third critical field H{sub c3}* > H{sub c2}. Below H{sub c2} such states produce a surface barrier of a new type. This barrier for the vortex entrance and exit is due to the strong increase of the order parameter near the hole edge. It keeps constant the number of captured vortices during the cooling at a fixed field. (2) An increase of the hole density or of the hole radius initiates a sharp redistribution of fluxoids: all of them drop inside holes. This first order transition leads to a localization of all vortices and consequently to a qualitative change of the transport properties (TAFF in this case). In the resulting new state the filling factor is not any more the same for neighboring holes and its averaged value is equal to the frustration of the hole network.« less

Superconducting traveling wave accelerators

DOE Office of Scientific and Technical Information (OSTI.GOV)

Farkas, Z.D.

1984-11-01

This note considers the applicability of superconductivity to traveling wave accelerators. Unlike CW operation of a superconducting standing wave or circulating wave accelerator section, which requires improvement factors (superconductor conductivity divided by copper conductivity) of about 10/sup 6/ in order to be of practical use, a SUperconducting TRaveling wave Accelerator, SUTRA, operating in the pulsed mode requires improvement factors as low as about 10/sup 3/, which are attainable with niobium or lead at 4.2K, the temperature of liquid helium at atmospheric pressure. Changing from a copper traveling wave accelerator to SUTRA achieves the following. (1) For a given gradient SUTRAmore » reduces the peak and average power requirements typically by a factor of 2. (2) SUTRA reduces the peak power still further because it enables us to increase the filling time and thus trade pulse width for gradient. (3) SUTRA makes possible a reasonably long section at higher frequencies. (4) SUTRA makes possible recirculation without additional rf average power. 8 references, 6 figures, 1 table.« less

Light transmittance and micro-mechanical properties of bulk fill vs. conventional resin based composites.

PubMed

Bucuta, Stefan; Ilie, Nicoleta

2014-11-01

The aim of this study was to quantify the blue light that passes through different incremental thicknesses of bulk fill in comparison to conventional resin-based composites (RBCs) and to relate it to the induced mechanical properties. Seven bulk fill, five nanohybrid and two flowable RBCs were analysed. Specimens (n = 5) of three incremental thicknesses (2, 4 and 6 mm) were cured from the top for 20 s, while at the bottom, a spectrometer monitored in real time the transmitted irradiance. Micro-mechanical properties (Vickers hardness, HV, and indentation modulus, E) were measured at the top and bottom after 24 h of storage in distilled water at 37 °C. Electron microscope images were taken for assessing the filler distribution and size. Bulk fill RBCs (except SonicFill) were more translucent than conventional RBCs. Low-viscosity bulk fill materials showed the lowest mechanical properties. HV depends highly on the following parameters: material (ηp (2) = 0.952), incremental thickness (0.826), filler volume (0.747), filler weight (0.746) and transmitted irradiance (0.491). The bottom-to-top HV ratio (HVbt) was higher than 80 % in all materials in 2- and 4-mm increments (except for Premise), whereas in 6-mm increments, this is valid only in four bulk fill materials (Venus Bulk Fill, SDR, x-tra fil, Tetric EvoCeram Bulk Fill). The depth of cure is dependent on the RBC's translucency. Low-viscosity bulk fill RBCs have lower mechanical properties than all other types of analysed materials. All bulk fill RBCs (except SonicFill) are more translucent for blue light than conventional RBCs. Although bulk fill RBCs are generally more translucent, the practitioner has to follow the manufacturer's recommendations on curing technique and maximum incremental thickness.

Integration of different data gap filling techniques to facilitate assessment of polychlorinated biphenyls: A proof of principle case study (ASCCT meeting)

EPA Science Inventory

Data gap filling techniques are commonly used to predict hazard in the absence of empirical data. The most established techniques are read-across, trend analysis and quantitative structure-activity relationships (QSARs). Toxic equivalency factors (TEFs) are less frequently used d...

Determination of sendust intrinsic permeability from microwave constitutive parameters of composites with sendust spheres and flakes

NASA Astrophysics Data System (ADS)

Starostenko, Sergey N.; Rozanov, Konstantin N.; Shiryaev, Artem O.; Shalygin, Alexander N.; Lagarkov, Andrey N.

2017-06-01

Intrinsic permeability of sendust alloys is determined from the measured microwave permittivity and permeability of composites filled with either spherical or flaky sendust powders. The permittivity and permeability measurements are performed applying the coaxial reflection-transmission technique in the 0.05 to 18 GHz frequency range. The effects of the filling factor, inclusion shape, and size on composite constitutive parameters are discussed. The permeability of metal inclusion is retrieved from the measured permeability of composites using a generalized Maxwell Garnett equation that accounts for the percolation threshold. The equation parameters are found by fitting the measured dependence of composite permittivity and permeability on frequency and filling. The inclusion dimensions calculated from the found parameters agree with the results of grain-size analyses. The alloy intrinsic permeability is retrieved from inclusion permeability with the account for skinning. The fitted frequency and damping factor of ferromagnetic resonance depend on the inclusion shape. The calculated reflectivity map of the flake-filled composite shows that sendust powders are promising fillers for interference suppressors and microwave absorbers at frequencies close to 1 GHz.

Characterization of subvisible particle formation during the filling pump operation of a monoclonal antibody solution.

PubMed

Nayak, Arpan; Colandene, James; Bradford, Victor; Perkins, Melissa

2011-10-01

Characterization and control of aggregate and subvisible particle formation during fill-finish process steps are important for biopharmaceutical products. The filling step is of key importance as there is no further filtration of the drug product beyond sterile filtration. Filling processes can impact product quality by introducing physical stresses such as shear, friction, and cavitation. Other detrimental factors include temperature generated in the process of filling, foaming, and contact with filling system materials, including processing aids such as silicone oil. Certain pumps may shed extrinsic particles that may lead to heterogeneous nucleation-induced aggregation. In this work, microflow imaging, size-exclusion chromatography (SEC), and turbidimetry were utilized to quantify subvisible particles, aggregation, and opalescence, respectively. The filling process was performed using several commonly used filling systems, including rotary piston pump, rolling diaphragm pump, peristaltic pump, and time-pressure filler. The rolling diaphragm pump, peristaltic pump, and time-pressure filler generated notably less protein subvisible particles than the rotary piston pump, although no change in aggregate content by SEC was observed by any pump. An extreme increase in subvisible particles was also reflected in an increase in turbidity. Copyright © 2011 Wiley-Liss, Inc.

Environmental and Genetic Contributions to Indicators of Oral Malodor in Twins

PubMed Central

Bretz, Walter A.; Biesbrock, A.; Corby, P. M; Corby, A. L.; Bretz, W. G.; Wessel, J.; Schork, N. J.

2011-01-01

This study aimed to: (1) determine concordance rates of self-reported and subjectively determined indicators of oral malodor in twins; (2) determine the relative contributions of genetic and environmental factors to levels of volatile sulfur compounds (VSCs) in intraoral and exhaled breath. Fifty-one twin pairs participated in the study. Measurements of VSCs were obtained by a halimeter. The presence of tongue coatings was determined and twins filled out a 32-item questionnaire on oral malodor indicators independently of one another. Estimates of heritability (h2) for halimeter measurements were computed by SOLAR. The concordance rates for the presence of tongue coating among identical and fraternal twins were 67% and 11%, respectively. In the 10 most informative items, 70% exhibited higher concordance rates for identical than for fraternal twins. Of particular interest were the differences in concordance rates for dry mouth, sinus infection and unusual sweating. The h2 for intraoral breath was 0.28 ± 0.17 (NS), whereas the h2 for exhaled breath was 0.50 ± 0.20 (p = .0207). The concordance rates of tongue coatings and malodor indicators were higher in identical twins than in fraternal twins. Intraoral breath VSC values were primarily attributable to environmental factors, whereas exhaled breath VSC values were partially explained by genetic factors. PMID:22506313

Physical activity promotion in schools: which strategies do schools (not) implement and which socioecological factors are associated with implementation?

PubMed

Cardon, Greet M; Van Acker, Ragnar; Seghers, Jan; De Martelaer, Kristine; Haerens, Leen L; De Bourdeaudhuij, Ilse M M

2012-06-01

We studied the implementation and associated factors of strategies (e.g. sports after school and during lunch break, active schoolyards, active school commuting) and organizational principles (e.g. safe bike racks, pupil involvement) that facilitate the physical activity (PA)-promoting role of schools. Key representatives of 111 elementary and 125 secondary schools filled out an online survey. Less than half of the elementary schools organized sports during lunch-break or after school. In secondary schools the least implemented strategies were the promotion of active school commuting and after-school sports. In general pupil, parental and community involvement scored low. Better knowledge of community schools and having attended in-service training were associated with higher implementation scores in elementary and secondary schools. Better implementation of the strategies was found in larger schools. Participation in activities from the School Sports Association and more perceived interest from parents and the school board were also associated with higher implementation scores. In conclusion, knowledge of community schools and in-service training next to sufficient human resources are potential key factors to promote PA. Efforts are needed to convince and help schools to increase parental and pupil involvement and to build a policy on school-community partnerships.

Correlation between Salivary Glucose and Blood Glucose and the Implications of Salivary Factors on the Oral Health Status in Type 2 Diabetes Mellitus Patients

PubMed Central

Puttaswamy, Kavitha A.; Puttabudhi, Jaishankar H.; Raju, Shashidara

2017-01-01

Aims and Objectives: The purpose of this study was to estimate and assess any correlation between random capillary blood glucose (RCBG) and unstimulated whole salivary glucose (UWSG), as well as to estimate various salivary parameters, such as flow rate, pH, buffering capacity, and the influence of these factors on the oral health status in type 2 diabetes mellitus (DM). Materials and Methods: Sixty individuals suffering from type 2 DM and 40 healthy individuals in the age group of 30–60 years were included in the study. RCBG was estimated using glucometer and UWSG was estimated using photocolorimeter. Salivary parameters such as flow rate, pH, and buffering capacity were assessed using GC® Saliva kit. Oral health status was recorded using the Russell's periodontal index (RPI) and the Decayed Missing Filled Teeth (DMFT) index. The Statistical Package for the Social Sciences version 16 was used for statistical analysis. Results: Type 2 diabetics had higher mean values for RCBG levels and UWSG. Type 2 diabetics had low mean salivary flow rate, pH, and buffering capacity. Type 2 diabetics had higher mean values for RPI. Conclusion: Among the salivary factors studied, salivary glucose significantly influenced the periodontal status in Type 2 diabetics. PMID:28316946

Correlation between Salivary Glucose and Blood Glucose and the Implications of Salivary Factors on the Oral Health Status in Type 2 Diabetes Mellitus Patients.

PubMed

Puttaswamy, Kavitha A; Puttabudhi, Jaishankar H; Raju, Shashidara

2017-01-01

The purpose of this study was to estimate and assess any correlation between random capillary blood glucose (RCBG) and unstimulated whole salivary glucose (UWSG), as well as to estimate various salivary parameters, such as flow rate, pH, buffering capacity, and the influence of these factors on the oral health status in type 2 diabetes mellitus (DM). Sixty individuals suffering from type 2 DM and 40 healthy individuals in the age group of 30-60 years were included in the study. RCBG was estimated using glucometer and UWSG was estimated using photocolorimeter. Salivary parameters such as flow rate, pH, and buffering capacity were assessed using GC ® Saliva kit. Oral health status was recorded using the Russell's periodontal index (RPI) and the Decayed Missing Filled Teeth (DMFT) index. The Statistical Package for the Social Sciences version 16 was used for statistical analysis. Type 2 diabetics had higher mean values for RCBG levels and UWSG. Type 2 diabetics had low mean salivary flow rate, pH, and buffering capacity. Type 2 diabetics had higher mean values for RPI. Among the salivary factors studied, salivary glucose significantly influenced the periodontal status in Type 2 diabetics.

Thermodynamic models for bounding pressurant mass requirements of cryogenic tanks

NASA Technical Reports Server (NTRS)

Vandresar, Neil T.; Haberbusch, Mark S.

1994-01-01

Thermodynamic models have been formulated to predict lower and upper bounds for the mass of pressurant gas required to pressurize a cryogenic tank and then expel liquid from the tank. Limiting conditions are based on either thermal equilibrium or zero energy exchange between the pressurant gas and initial tank contents. The models are independent of gravity level and allow specification of autogenous or non-condensible pressurants. Partial liquid fill levels may be specified for initial and final conditions. Model predictions are shown to successfully bound results from limited normal-gravity tests with condensable and non-condensable pressurant gases. Representative maximum collapse factor maps are presented for liquid hydrogen to show the effects of initial and final fill level on the range of pressurant gas requirements. Maximum collapse factors occur for partial expulsions with large final liquid fill fractions.

Urothelium update: how the bladder mucosa measures bladder filling.

PubMed

Janssen, D A W; Schalken, J A; Heesakkers, J P F A

2017-06-01

This review critically evaluates the evidence on mechanoreceptors and pathways in the bladder urothelium that are involved in normal bladder filling signalling. Evidence from in vitro and in vivo studies on (i) signalling pathways like the adenosine triphosphate pathway, cholinergic pathway and nitric oxide and adrenergic pathway, and (ii) different urothelial receptors that are involved in bladder filling signalling like purinergic receptors, sodium channels and TRP channels will be evaluated. Other potential pathways and receptors will also be discussed. Bladder filling results in continuous changes in bladder wall stretch and exposure to urine. Both barrier and afferent signalling functions in the urothelium are constantly adapting to cope with these dynamics. Current evidence shows that the bladder mucosa hosts essential pathways and receptors that mediate bladder filling signalling. Intracellular calcium ion increase is a dominant factor in this signalling process. However, there is still no complete understanding how interacting receptors and pathways create a bladder filling signal. Currently, there are still novel receptors investigated that could also be participating in bladder filling signalling. Normal bladder filling sensation is dependent on multiple interacting mechanoreceptors and signalling pathways. Research efforts need to focus on how these pathways and receptors interact to fully understand normal bladder filling signalling. © 2016 Scandinavian Physiological Society. Published by John Wiley & Sons Ltd.

Small-bandgap polymer solar cells with unprecedented short-circuit current density and high fill factor.

PubMed

Choi, Hyosung; Ko, Seo-Jin; Kim, Taehyo; Morin, Pierre-Olivier; Walker, Bright; Lee, Byoung Hoon; Leclerc, Mario; Kim, Jin Young; Heeger, Alan J

2015-06-03

Small-bandgap polymer solar cells (PSCs) with a thick bulk heterojunction film of 340 nm exhibit high power conversion efficiencies of 9.40% resulting from high short-circuit current density (JSC ) of 20.07 mA cm(-2) and fill factor of 0.70. This remarkable efficiency is attributed to maximized light absorption by the thick active layer and minimized recombination by the optimized lateral and vertical morphology through the processing additive. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Spatial evolution of laser filaments in turbulent air

NASA Astrophysics Data System (ADS)

Zeng, Tao; Zhu, Shiping; Zhou, Shengling; He, Yan

2018-04-01

In this study, the spatial evolution properties of laser filament clusters in turbulent air were evaluated using numerical simulations. Various statistical parameters were calculated, such as the percolation probability, filling factor, and average cluster size. The results indicate that turbulence-induced multi-filamentation can be described as a new phase transition universality class. In addition, during this process, the relationship between the average cluster size and filling factor could be fit by a power function. Our results are valuable for applications involving filamentation that can be influenced by the geometrical features of multiple filaments.

Factors Associated with Dental Caries in a Group of American Indian Children at age 36 Months

PubMed Central

Warren, John J.; Blanchette, Derek; Dawson, Deborah V.; Marshall, Teresa A.; Phipps, Kathy R.; Starr, Delores; Drake, David R.

2015-01-01

Objectives Early childhood caries (ECC) is rampant among American Indian children, but there has been relatively little study of this problem. This paper reports on risk factors for caries for a group of American Indian children at age 36 months as part of a longitudinal study. Methods Pregnant women from a Northern Plains Tribal community were recruited to participate in a longitudinal study of caries and caries risk factors. Standardized dental examinations were completed on children and questionnaires were completed by mothers at baseline and when children were 4, 8, 12, 16, 22, 28 and 36 months of age. Examinations were surface-specific for dental caries, and the questionnaires collected data on demographic, dietary and behavioral factors. Non-parametric bivariate tests and logistic regression models were used to identify risk factors for caries at 36 months, and negative binomial regression was used to identify factors related to caries severity (dmf counts). Results Among the 232 children, and caries prevalence for cavitated lesions was 80%, with an additional 15% having only non-cavitated lesions. The mean dmfs was 9.6, and of the total dmfs, nearly 62% of affected surfaces were decayed, 31% were missing, and 7% were filled. Logistic regression identified higher added sugar beverage consumption, younger maternal age at baseline, higher maternal DMFS at baseline, and greater number of people in the household as significant (p<0.05) risk factors. Negative binomial regression found that only maternal DMFS was associated with child dmf counts. Conclusions By the age of 36 months, dental caries is nearly universal in this population of American Indian children. Caries risk factors included sugared beverage consumption, greater household size and maternal factors, but further analyses are needed to better understand caries in this population. PMID:26544674

Energy propagation by transverse waves in multiple flux tube systems using filling factors

DOE Office of Scientific and Technical Information (OSTI.GOV)

Van Doorsselaere, T.; Gijsen, S. E.; Andries, J.

2014-11-01

In the last few years, it has been found that transverse waves are present at all times in coronal loops or spicules. Their energy has been estimated with an expression derived for bulk Alfvén waves in homogeneous media, with correspondingly uniform wave energy density and flux. The kink mode, however, is localized in space with the energy density and flux dependent on the position in the cross-sectional plane. The more relevant quantities for the kink mode are the integrals of the energy density and flux over the cross-sectional plane. The present paper provides an approximation to the energy propagated bymore » kink modes in an ensemble of flux tubes by means of combining the analysis of single flux tube kink oscillations with a filling factor for the tube cross-sectional area. This finally allows one to compare the expressions for energy flux of Alfvén waves with an ensemble of kink waves. We find that the correction factor for the energy in kink waves, compared to the bulk Alfvén waves, is between f and 2f, where f is the density filling factor of the ensemble of flux tubes.« less

Benzothiadiazole Versus Thiophene: Influence of the Auxiliary Acceptor on the Photovoltaic Properties of Donor-Acceptor-Based Copolymers.

PubMed

Li, Zongbo; Weng, Kangkang; Chen, Aihua; Sun, Xiaobo; Wei, Donghui; Yu, Mingming; Huo, Lijun; Sun, Yanming

2018-01-01

Two donor-acceptor (D-A) type conjugated copolymers, P1 and P2, are designed and synthesized. A classical benzothiadiazole acceptor is used to replace a thiophene unit in the polymer chain of P1 to obtain P2 terpolymer. Compared with P1, P2 exhibits broader absorption spectra, higher absorption coefficient, deeper lowest unoccupied molecular orbital level, and a relatively lower band gap. As a result, the P2-based solar cell exhibits a high power conversion efficiency (PCE) of 6.60%, with a short-circuit current (J sc ) of 12.43 mA cm -2 , and a fill factor (FF) of 73.1%, which are higher than those of the P1-based device with a PCE of 4.70%, a J sc of 9.43 mA cm -2 , and an FF of 61.6%. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Adolescence and the consumption of psychoactive substances: the impact of the socioeconomic status.

PubMed

Pratta, Elisângela Maria Machado; dos Santos, Manoel Antônio

2007-01-01

Recent studies have pointed that it is necessary to define the impact of specific dimensions of the social-economic context that can work as risk factors regarding drug addiction. This study aimed to verify potential relationships between the drug addiction during adolescence and the social-economic level. A total of 568 adolescents participated in this study answering an anonymous self-filled questionnaire. The analyses involved the description of the variable distribution in the sample and statistical analyzes to determine the differences found. Contrary to the common sense, adolescents from the higher social classes presented a significant higher perceptual of alcohol, tobacco, weed and solvent consumption when compared to their counterparts from lower social classes. These data suggest the importance of studies that seek to clarify the possible influences of the social-economic status on the consumption of drugs among adolescents.

Under Pressure: Intraluminal Filling Pressures of Postpartum Hemorrhage Tamponade Balloons

PubMed Central

Antony, Kathleen M.; Racusin, Diana A.; Belfort, Michael A.; Dildy, Gary A.

2017-01-01

Objective Uterine tamponade by fluid-filled balloons is now an accepted method of controlling postpartum hemorrhage. Available tamponade balloons vary in design and material, which affects the filling attributes and volume at which they rupture. We aimed to characterize the filling capacity and pressure-volume relationship of various tamponade balloons. Study Design Balloons were filled with water ex vivo. Intraluminal pressure was measured incrementally (every 10 mL for the Foley balloons and every 50 mL for all other balloons). Balloons were filled until they ruptured or until 5,000 mL was reached. Results The Foley balloons had higher intraluminal pressures than the larger-volume balloons. The intraluminal pressure of the Sengstaken-Blakemore tube (gastric balloon) was initially high, but it decreased until shortly before rupture occurred. The Bakri intraluminal pressure steadily increased until rupture occurred at 2,850 mL. The condom catheter, BT-Cath, and ebb all had low intraluminal pressures. Both the BT-Cath and the ebb remained unruptured at 5,000 mL. Conclusion In the setting of acute hemorrhage, expeditious management is critical. Balloons that have a low intraluminal pressure-volume ratio may fill more rapidly, more easily, and to greater volumes. We found that the BT-Cath, the ebb, and the condom catheter all had low intraluminal pressures throughout filling. PMID:28497006

Dental caries and their association with socioeconomic characteristics, oral hygiene practices and eating habits among preschool children in Abu Dhabi, United Arab Emirates - the NOPLAS project.

PubMed

Elamin, Amal; Garemo, Malin; Gardner, Andrew

2018-06-08

Dental caries are a global public health problem and influence the overall health of children. The risk factors for caries include biological, socio-behavioral and environmental factors. This cross-sectional study assessed dental caries and their associations with socioeconomic factors, oral hygiene practices and eating habits among Emirati and non-Emirati children in Abu Dhabi, United Arab Emirates (UAE). The stratified sample comprised children aged 18 months to 4 years recruited from 7 nurseries. The World Health Organization (WHO) decayed, missing and filled teeth index (dmft) was used to analyze the dental status of the children. Parents completed a questionnaire regarding demographics, food consumption and oral habits. The study was approved by the Research Ethics Committee at Zayed University, UAE (ZU15_029_F). A total of 186 children with a mean age of 2.46 years, of which 46.2% were Emirati, participated. Overall, 41% of the children had dental caries. The mean dmft±SD was 1.70 ± 2.81 with a mean ± SD decayed component (dt) of 1.68 ± 2.80 and mean ± SD filled component (ft) of 0.02 ± 0.19. Emirati children showed higher mean dmft, Plaque Index and Significant Carries Index values than non-Emirati children (P < 0.000). Low maternal education, rural nursery location, infrequent tooth-brushing, frequent consumption of high-sugar food items and Emirati nationality were factors significantly associated with dental caries. In this study, 4 out of 10 nursery children were found to have dental caries. Sociodemographic factors, dietary and oral health habits were associated with dental caries. Effective oral health interventions tailored to improve eating habits and the dental screening of children in this age group are imperative to mitigate these concerns.

Sleep disturbances and teacher ratings of school achievement and temperament in children.

PubMed

Bruni, Oliviero; Ferini-Strambi, Luigi; Russo, Paolo M; Antignani, Massimo; Innocenzi, Margherita; Ottaviano, Paola; Valente, Donatella; Ottaviano, Salvatore

2006-01-01

The current study examined the relationships between academic achievement, sleep, temperament and demographic-historical data in school-age children. Teachers were asked to fill out the teacher temperament questionnaire and a form for school achievement, while mothers filled out a demographic-historical form and the sleep disturbance scale for children (SDSC), a 26-item questionnaire that consisted of six factors: difficulty in initiating and maintaining sleep (DIMS), sleep breathing disorders (SBD), arousal disorders (DA), sleep-wake transition disorders (SWTD), disorders of excessive somnolence (DOES), sleep hyperhydrosis (SHY). From a sample of 380 school children, 264 (70%) were suitable for the analyses (141 M and 123 F aged 8-11 years, mean 9.6 years). A school achievement index (SAI) was derived, summing up four items (reading ability, reading comprehension, mathematics, executive ability) of the teacher form for school achievement. SAI mean for the total sample was 11.1 (SD=2.8). A significant gender difference was found: females have higher SAI than males. The analysis of the demographic-historical form showed that only two factors appeared to affect SAI score: enuresis and the low educational level of the mother. The pattern of correlations showed that (a) the SAI was negatively related to the SDSC total score, in particular to DIMS and DOES sub-factors, and (b) the SAI was significantly and positively correlated with the temperamental traits of task-orientation and personal-social flexibility. A multiple stepwise regression analysis showed that the temperamental traits task-orientation and personal-social flexibility are the most predictive factors for SAI while the mother's educational level and the SDSC total score, although they contributed significantly to the prediction of SAI, accounted for only a small portion of variance. Temperament and sleep are important factors influencing school achievement, and their assessment could help to identify children at risk regarding school achievement.

Impact of Multiple Pharmacy Use on Medication Adherence and Drug-drug Interactions in Older Adults with Medicare Part D

PubMed Central

Marcum, Zachary A.; Driessen, Julia; Thorpe, Carolyn T.; Gellad, Walid F.; Donohue, Julie M.

2014-01-01

Objective To assess the association between multiple pharmacy use and medication adherence and potential drug-drug interactions (DDIs) among older adults. Design, Setting, and Participants Cross-sectional propensity score-weighted analysis of 2009 claims data from a nationally representative sample of 926,956 Medicare Part D beneficiaries aged >65 continuously enrolled in fee-for-service Medicare and Part D that year, and filled >1 prescription at a community/retail or mail order pharmacy. Multiple pharmacy use was defined as concurrent (overlapping time periods) or sequential use (non-overlapping time periods) of >2 pharmacies in the year. Measurements Medication adherence was calculated using a proportion of days covered ≥0.80 for eight therapeutic categories (β-blockers, renin angiotensin system antagonists, calcium channel blockers, statins, sulfonylureas, biguanides [i.e., metformin], thiazolidinediones, and dipeptidyl peptidase-IV inhibitors). Potential DDIs arising from use of certain drugs across a broad set of classes were defined as the concurrent filling of two interacting drugs. Results Overall, 38.1% of the sample used multiple pharmacies. Those using multiple pharmacies (both concurrently and sequentially) consistently had higher adjusted odds of non-adherence (ranging from 1.10 to 1.31, p<0.001) across all chronic medication classes assessed after controlling for socio-demographic, health status and access to care factors, compared to single pharmacy users. The adjusted predicted probability of exposure to a DDI was also slightly higher for those using multiple pharmacies concurrently (3.6%) compared to single pharmacy users (3.2%, AOR 1.11, 95% CI 1.08–1.15) but lower in individuals using multiple pharmacies sequentially (2.8%, AOR 0.85, 95% CI 0.81–0.91). Conclusions Filling prescriptions at multiple pharmacies was associated with lower medication adherence across multiple chronic medications, and a small but statistically significant increase in DDIs among concurrent pharmacy users. PMID:24521363

High Efficiency Organic/Silicon-Nanowire Hybrid Solar Cells: Significance of Strong Inversion Layer

PubMed Central

Yu, Xuegong; Shen, Xinlei; Mu, Xinhui; Zhang, Jie; Sun, Baoquan; Zeng, Lingsheng; Yang, Lifei; Wu, Yichao; He, Hang; Yang, Deren

2015-01-01

Organic/silicon nanowires (SiNWs) hybrid solar cells have recently been recognized as one of potentially low-cost candidates for photovoltaic application. Here, we have controllably prepared a series of uniform silicon nanowires (SiNWs) with various diameters on silicon substrate by metal-assisted chemical etching followed by thermal oxidization, and then fabricated the organic/SiNWs hybrid solar cells with poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS). It is found that the reflective index of SiNWs layer for sunlight depends on the filling ratio of SiNWs. Compared to the SiNWs with the lowest reflectivity (LR-SiNWs), the solar cell based on the SiNWs with low filling ratio (LF-SiNWs) has a higher open-circuit voltage and fill factor. The capacitance-voltage measurements have clarified that the built-in potential barrier at the LF-SiNWs/PEDOT:PSS interface is much larger than that at the LR-SiNWs/PEDOT one, which yields a strong inversion layer generating near the silicon surface. The formation of inversion layer can effectively suppress the carrier recombination, reducing the leakage current of solar cell, and meanwhile transfer the LF-SiNWs/PEDOT:PSS device into a p-n junction. As a result, a highest efficiency of 13.11% is achieved for the LF-SiNWs/PEDOT:PSS solar cell. These results pave a way to the fabrication of high efficiency organic/SiNWs hybrid solar cells. PMID:26610848

How does tissue regeneration influence the mechanical behavior of additively manufactured porous biomaterials?

PubMed

Hedayati, R; Janbaz, S; Sadighi, M; Mohammadi-Aghdam, M; Zadpoor, A A

2017-01-01

Although the initial mechanical properties of additively manufactured porous biomaterials are intensively studied during the last few years, almost no information is available regarding the evolution of the mechanical properties of implant-bone complex as the tissue regeneration progresses. In this paper, we studied the effects of tissue regeneration on the static and fatigue behavior of selective laser melted porous titanium structures with three different porosities (i.e. 77, 81, and 85%). The porous structures were filled with four different polymeric materials with mechanical properties in the range of those observed for de novo bone (0.7GPa

High Efficiency Organic/Silicon-Nanowire Hybrid Solar Cells: Significance of Strong Inversion Layer.

PubMed

Yu, Xuegong; Shen, Xinlei; Mu, Xinhui; Zhang, Jie; Sun, Baoquan; Zeng, Lingsheng; Yang, Lifei; Wu, Yichao; He, Hang; Yang, Deren

2015-11-27

Organic/silicon nanowires (SiNWs) hybrid solar cells have recently been recognized as one of potentially low-cost candidates for photovoltaic application. Here, we have controllably prepared a series of uniform silicon nanowires (SiNWs) with various diameters on silicon substrate by metal-assisted chemical etching followed by thermal oxidization, and then fabricated the organic/SiNWs hybrid solar cells with poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) ( PSS). It is found that the reflective index of SiNWs layer for sunlight depends on the filling ratio of SiNWs. Compared to the SiNWs with the lowest reflectivity (LR-SiNWs), the solar cell based on the SiNWs with low filling ratio (LF-SiNWs) has a higher open-circuit voltage and fill factor. The capacitance-voltage measurements have clarified that the built-in potential barrier at the LF-SiNWs/ PSS interface is much larger than that at the LR-SiNWs/PEDOT one, which yields a strong inversion layer generating near the silicon surface. The formation of inversion layer can effectively suppress the carrier recombination, reducing the leakage current of solar cell, and meanwhile transfer the LF-SiNWs/ PSS device into a p-n junction. As a result, a highest efficiency of 13.11% is achieved for the LF-SiNWs/ PSS solar cell. These results pave a way to the fabrication of high efficiency organic/SiNWs hybrid solar cells.

Grain Filling Characteristics and Their Relations with Endogenous Hormones in Large- and Small-Grain Mutants of Rice.

PubMed

Zhang, Weiyang; Cao, Zhuanqin; Zhou, Qun; Chen, Jing; Xu, Gengwen; Gu, Junfei; Liu, Lijun; Wang, Zhiqin; Yang, Jianchang; Zhang, Hao

2016-01-01

This study determined if the variation in grain filling parameters between two different spikelet types of rice (Oryza sativa L.) is regulated by the hormonal levels in the grains. Two rice mutants, namely, a large-grain mutant (AZU-M) and a small-grain mutant (ZF802-M), and their respective wild types (AZU-WT and ZF802-WT) were grown in the field. The endosperm cell division rate, filling rate, and hormonal levels: zeatin + zeatin riboside (Z+ZR), indo-3-acetic acid (IAA), polyamines (PAs), and abscisic acid (ABA) were determined. The results showed that there was no significant difference between the filling and endosperm cell division rates. These rates were synchronous between the superior and inferior spikelets for both mutants. However, the abovementioned parameters were significantly different between the two spikelet types for the two wild types. The superior spikelets filled faster and their filling rate was higher compared to the inferior ones. Changes in the concentrations of plant hormones were consistent with the observed endosperm cell division rate and the filling rate for both types of spikelets of mutant and wild type plants. Regression analysis showed a significant positive correlation between cell division and filling rates with the concentrations of the investigated hormones. Exogenous chemical application verified the role of ABA, IAA, and PAs in grain filling. The results indicate that poor filling of inferior spikelets in rice occurs primarily due to the reduced hormone concentrations therein, leading to lower division rate of endosperm cells, fewer endosperm cells, slower filling rate, and smaller grain weight.

Grain Filling Characteristics and Their Relations with Endogenous Hormones in Large- and Small-Grain Mutants of Rice

PubMed Central

Zhang, Weiyang; Cao, Zhuanqin; Zhou, Qun; Chen, Jing; Xu, Gengwen; Gu, Junfei; Liu, Lijun; Wang, Zhiqin; Yang, Jianchang; Zhang, Hao

2016-01-01

This study determined if the variation in grain filling parameters between two different spikelet types of rice (Oryza sativa L.) is regulated by the hormonal levels in the grains. Two rice mutants, namely, a large-grain mutant (AZU-M) and a small-grain mutant (ZF802-M), and their respective wild types (AZU-WT and ZF802-WT) were grown in the field. The endosperm cell division rate, filling rate, and hormonal levels: zeatin + zeatin riboside (Z+ZR), indo-3-acetic acid (IAA), polyamines (PAs), and abscisic acid (ABA) were determined. The results showed that there was no significant difference between the filling and endosperm cell division rates. These rates were synchronous between the superior and inferior spikelets for both mutants. However, the abovementioned parameters were significantly different between the two spikelet types for the two wild types. The superior spikelets filled faster and their filling rate was higher compared to the inferior ones. Changes in the concentrations of plant hormones were consistent with the observed endosperm cell division rate and the filling rate for both types of spikelets of mutant and wild type plants. Regression analysis showed a significant positive correlation between cell division and filling rates with the concentrations of the investigated hormones. Exogenous chemical application verified the role of ABA, IAA, and PAs in grain filling. The results indicate that poor filling of inferior spikelets in rice occurs primarily due to the reduced hormone concentrations therein, leading to lower division rate of endosperm cells, fewer endosperm cells, slower filling rate, and smaller grain weight. PMID:27780273

Use of palm mid-fraction in dark chocolate as base filling centre at different storage temperatures.

PubMed

Jinap, S; Ali, A A; Man, Y B; Suria, A M

2000-11-01

Dark chocolates filled with palm mid-fraction (PMF) were stored at different temperatures to evaluate the physical and chemical changes. Storage at low temperature (18 degrees C) reduces the PMF migration to negligible extent. Higher storage temperatures (30 and 35 degrees C) increased the PMF migration from the filling centre into the chocolate coating. As a consequence of fat migration, fatty acid composition, triglyceride composition, hardness, solid fat content, melting point and polymorphic structure changed, leading to bloom formation, which started by fat migration and was influenced by recrystallization tendency within the chocolate coating.

An Efficient Scheme for Updating Sparse Cholesky Factors

NASA Technical Reports Server (NTRS)

Raghavan, Padma

2002-01-01

Raghavan had earlier developed the software package DCSPACK which can be used for solving sparse linear systems where the coefficient matrix is symmetric and positive definite (this project was not funded by NASA but by agencies such as NSF). DSCPACK-S is the serial code and DSCPACK-P is a parallel implementation suitable for multiprocessors or networks-of-workstations with message passing using MCI. The main algorithm used is the Cholesky factorization of a sparse symmetric positive positive definite matrix A = LL(T). The code can also compute the factorization A = LDL(T). The complexity of the software arises from several factors relating to the sparsity of the matrix A. A sparse N x N matrix A has typically less that cN nonzeroes where c is a small constant. If the matrix were dense, it would have O(N2) nonzeroes. The most complicated part of such sparse Cholesky factorization relates to fill-in, i.e., zeroes in the original matrix that become nonzeroes in the factor L. An efficient implementation depends to a large extent on complex data structures and on techniques from graph theory to reduce, identify, and manage fill. DSCPACK is based on an efficient multifrontal implementation with fill-managing algorithms and implementation arising from earlier research by Raghavan and others. Sparse Cholesky factorization is typically a four step process: (1) ordering to compute a fill-reducing numbering, (2) symbolic factorization to determine the nonzero structure of L, (3) numeric factorization to compute L, and, (4) triangular solution to solve L(T)x = y and Ly = b. The first two steps are symbolic and are performed using the graph of the matrix. The numeric factorization step is of dominant cost and there are several schemes for improving performance by exploiting the nested and dense structure of groups of columns in the factor. The latter are aimed at better utilization of the cache-memory hierarchy on modem processors to prevent cache-misses and provide execution rates (operations/second) that are close to the peak rates for dense matrix computations. Currently, EPISCOPACY is being used in an application at NASA directed by J. Newman and M. James. We propose the implementation of efficient schemes for updating the LL(T) or LDL(T) factors computed in DSCPACK-S to meet the computational requirements of their project. A brief description is provided in the next section.

ASRM Case Insulation development

NASA Technical Reports Server (NTRS)

Tam, W. F. S.; Bell, M.

1993-01-01

The ASRM Case Insulation Program used design of experiments to develop a high performance case insulation. The program traded-off more than thirty properties in areas of ablation performance, material properties, processibility, bonding/aging. Kevlar pulp was found to be the most significant factor. The low-molecular weight ethylene propylene diene monomer, EPDM was the second most significant factor. The curative was the third most significant factor. The tackifier was the fourth most significant factor. The stripwinding process for applying the insulation onto the case inner surfaces was also studied. The parameters selected for experiment were extruder speed, upper roller temperature and extruder nozzle temperature. The extrudability results showed that non-Kevlar filled formulations displayed optimum edges but poor thickness continuity. High Kevlar filled formulations displayed optimum thickness continuity but poor strip edge ratings.

ASRM Case Insulation development

NASA Astrophysics Data System (ADS)

Tam, W. F. S.; Bell, M.

1993-06-01

The ASRM Case Insulation Program used design of experiments to develop a high performance case insulation. The program traded-off more than thirty properties in areas of ablation performance, material properties, processibility, bonding/aging. Kevlar pulp was found to be the most significant factor. The low-molecular weight ethylene propylene diene monomer, EPDM was the second most significant factor. The curative was the third most significant factor. The tackifier was the fourth most significant factor. The stripwinding process for applying the insulation onto the case inner surfaces was also studied. The parameters selected for experiment were extruder speed, upper roller temperature and extruder nozzle temperature. The extrudability results showed that non-Kevlar filled formulations displayed optimum edges but poor thickness continuity. High Kevlar filled formulations displayed optimum thickness continuity but poor strip edge ratings.

Investigations into the thermal non-equilibrium of W UMa-type contact binaries

NASA Astrophysics Data System (ADS)

Xiong, Xiao; Liu, Liang; Qian, Sheng-Bang

2018-05-01

Traditionally, some physical details (e.g., magnetic braking, energy transfer, angular momentum loss, etc.) have to be taken into consideration during investigations into the evolution of contact binaries. However, the real evolutionary processes which usually contain several of these physical mechanisms are very complicated as a result of strong interaction between components. To avoid dealing with these factors, a linear relationship is applied to the temperatures of components. It is found that the higher the mass ratio (M 2/M 1) of a contact system, the weaker the deviation from thermal equilibrium. On this basis, a variation trend of fill-out factor (f) changing with mass ratio can be inferred, which is consistent with observations. Moreover, if we stick to this point of view, it should be natural that the number of semi-detached binaries in the predicted broken-contact phase of relaxation oscillations is less than the number in the contact phase.

Achieving Ultrahigh Carrier Mobility in Two-Dimensional Hole Gas of Black Phosphorus.

PubMed

Long, Gen; Maryenko, Denis; Shen, Junying; Xu, Shuigang; Hou, Jianqiang; Wu, Zefei; Wong, Wing Ki; Han, Tianyi; Lin, Jiangxiazi; Cai, Yuan; Lortz, Rolf; Wang, Ning

2016-12-14

We demonstrate that a field-effect transistor (FET) made of few-layer black phosphorus (BP) encapsulated in hexagonal boron nitride (h-BN) in vacuum exhibits a room-temperature hole mobility of 5200 cm 2 /(Vs), being limited just by the phonon scattering. At cryogenic temperatures, the FET mobility increases up to 45 000 cm 2 /(Vs), which is five times higher compared to the mobility obtained in earlier reports. The unprecedentedly clean h-BN-BP-h-BN heterostructure exhibits Shubnikov-de Haas oscillations and a quantum Hall effect with Landau level (LL) filling factors down to v = 2 in conventional laboratory magnetic fields. Moreover, carrier density independent effective mass of m * = 0.26 m 0 is measured, and a Landé g-factor of g = 2.47 is reported. Furthermore, an indication for a distinct hole transport behavior with up- and down-spin orientations is found.

Push-out bond strength of root fillings made with C-Point and BC sealer versus gutta-percha and AH Plus after the instrumentation of oval canals with the Self-Adjusting File versus WaveOne.

PubMed

Pawar, A M; Pawar, S; Kfir, A; Pawar, M; Kokate, S

2016-04-01

To compare the push-out bond strength exhibited by root fillings performed with either C-Point and Endosequence® BC sealer™ (BC Sealer) or gutta-percha and AH Plus® after the instrumentation of oval canals with either the Self-Adjusting File (SAF) System or WaveOne (WO) reciprocating file. Eighty extracted premolars were selected and divided randomly into the following four groups (n = 20): group 1, SAF instrumentation and filling using gutta-percha and AH Plus sealer; group 2, SAF instrumentation and C-Point and BC sealer filling; group 3, WO instrumentation and filling using gutta-percha and AH Plus sealer; and group 4, WO instrumentation and filling with C-Point and BC sealer. Sodium hypochlorite (5.25%) and EDTA (17%) were used as irrigants for all groups. After the sealer was set completely, the teeth were prepared for micro push-out assessment using 1.0-mm-thick root slices. Loading was performed with a universal testing machine at a speed of 0.5 mm min(-1) . Two-way anova and Student's t-test for pairwise comparisons were used to compare groups. All specimens filled with C-Point and BC sealer were associated with significantly higher push-out bond strength compared with gutta-percha and AH Plus sealer (P < 0.001). The bond strength was higher for the coronal and apical samples of the C-Point/BC sealer/SAF group (6.6 ± 0.3 and 3.2 ± 0.3 MPa) versus those of the gutta-percha/AH Plus/WO group (4.8 ± 0.3 and 1.8 ± 0.3 MPa), by 38% and by 80% in the coronal and apical parts, respectively (P < 0.001, P < 0.0001). Adhesive bond failure was more common in the WaveOne-instrumented group in general and in the buccal and lingual recesses in this group in particular. In oval canals, the instrument used and the root filling material significantly affected the push-out values of root fillings. The highest value was recorded in oval root canals instrumented with the SAF System and filled with C-Point and BC sealer, whereas the lowest strength was noted in oval canals instrumented with WaveOne and filled with gutta-percha and AH Plus sealer. © 2015 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Oral health status, salivary pH status, and Streptococcus mutans counts in dental plaques and saliva of children with acute lymphoblastic leukemia.

PubMed

Mazaheri, Romina; Jabbarifar, Ebrahim; Ghasemi, Elnaz; Akkafzadeh, Elahe; Poursaeid, Elmira

2017-01-01

Acute lymphoblastic leukemia (ALL), accounting for 23% of all malignancies in children, is the most prevalent pediatric malignancy. This study compared dental caries, oral hygiene status, salivary pH, and Streptococcus mutans counts in dental plaques and saliva of children with leukemia with those of healthy controls. This case-control cross-sectional study assessed 32 children with ALL and 32 healthy children (4-9-year-old) for gingival bleeding index (GBI), decayed, missing, and filled/decayed, missing, and filled surfaces (DMF/dmfs), and plaque index (PI). Sampling was performed to determine salivary pH and S. mutans counts of the participants. The two groups matched in terms of age, gender, and socioeconomic status. The groups were compared using independent t-test, Mann-Whitney test, Chi-square test, and Spearman's and Pearson's correlation analyses. The mean DMF/dmfs and GBI were significantly higher in the ALL group (P DMF / dmfs = 0.03; P GBI = 0.04). However, the two groups were not significantly different in the mean PI values ( P = 0.47). The mean S. mutans counts in dental plaques and saliva of the children with leukemia were significantly lower than the healthy controls ( P < 0.01). Moreover, the mean salivary pH was significantly lower in the ALL group compared to the control group ( P < 0.01). Higher caries and gingival bleeding rates, higher dental plaque accumulation in children with ALL, decreased salivary pH, and cumulative effects of other risk factors highlight the significance of oral hygiene training programs (for the parents of these children) and regular dental examinations for these children.

Investigation of sub-slab pressure field extension in specified granular fill materials incorporating a sump-based soil depressurisation system for radon mitigation.

PubMed

Hung, Le Chi; Goggins, Jamie; Fuente, Marta; Foley, Mark

2018-05-14

Design of bearing layers (granular fill material layers) is important for a house with a soil depressurisation (SD) system for indoor radon mitigation. These layers should not only satisfy the bearing capacity and serviceability criteria but should also provide a sufficient degree of the air permeability for the system. Previous studies have shown that a critical parameter for a SD system is the sub-slab pressure field extension in the bearing layers, but this issue has not been systematically investigated. A series of two-dimensional computational fluid dynamic simulations that investigate the behaviour of the sub-slab pressure field extension developed in a SD system is presented in this paper. The SD system considered in this paper consists of a granular fill material layer and a radon sump. The granular fill materials are 'T1 Struc' and 'T2 Perm', which are standard materials for building in the Republic of Ireland. Different conditions, which might be encountered in a practical situation, were examined. The results show that the air permeability and thickness of the granular fill materials are the two key factors which affect the sub slab pressure field extension (SPFE) significantly. Furthermore, the air permeability of native soil is found to be a fundamental factor for the SPFE so that it should be well understood when designing a SD system. Therefore, these factors should be considered sufficiently in each practical situation. Finally, a significant improvement of the pressure field extension can be achieved by ensuring air tightness of the SD system. Copyright © 2018 Elsevier B.V. All rights reserved.

A 4 year follow-up study of alveolar bone height influenced by two dissimilar Class II amalgam restorations.

PubMed

Fisher, D; Markitziu, A; Fishel, D; Brayer, L

1984-07-01

Fifty-four paired, approximal amalgam fillings, extended (E) versus unextended (NE) were placed in forty-three patients and followed up to 4 years. Yearly measurements between the alveolar crest and (a) the apical margin of the fillings (E, NE), and (b) the cemento-enamel junction of the control group, were performed using bite-wing radiographs joined to a translucent grid magnified ten-fold. The rate of alveolar crest resorption was similar for the control (C) and the unextended filling (NE) and reached 0.45 mm after 4 years of follow-up. The resorption of the alveolar crest under the extended (E) filling was significantly higher and reached 0.80 mm after 4 years (P less than 0.001).

Different Signatures of the Total Filling Factor 1 State

NASA Astrophysics Data System (ADS)

Tiemann, Lars; Yoon, Youngsoo; Schmult, Stefan; Hauser, Maik; Dietsche, Werner; von Klitzing, Klaus

2009-03-01

Bringing two 2-dimensional electron systems in close proximity can yield a correlated state as the electrons will experience the presence of the neighboring system. At the individual filling factors of 1/2 this leads to a new double-layer ground state as positive and negative charges from opposite layers couple to excitons. Many remarkable properties were found such as vanishing Hall and longitudinal resistances in the counterflow configuration [1], a resonantly enhanced zero bias tunneling peak [2], and more recently, a critical DC tunneling current and vanishingly small interlayer resistances in DC measurements [3]. We will show how it is possible to combine the results of these three different measurements into a consistent picture. Under certain conditions it is possible to exceed the critical currents but still observe a minimum at total filling factor 1 in the counterflow configuration.[1] M. Kellogg et al. PRL 93, 036801 (2004); E. Tutuc et al. PRL 93, 036802 (2004)[2] I.B. Spielman et al., PRL 87, 036803 (2001)[3] L. Tiemann et al., New Journal of Physics 10, 045018 (2008)

Advancements in high-power high-brightness laser bars and single emitters for pumping and direct diode application

NASA Astrophysics Data System (ADS)

An, Haiyan; Jiang, Ching-Long J.; Xiong, Yihan; Zhang, Qiang; Inyang, Aloysius; Felder, Jason; Lewin, Alexander; Roff, Robert; Heinemann, Stefan; Schmidt, Berthold; Treusch, Georg

2015-03-01

We have continuously optimized high fill factor bar and packaging design to increase power and efficiency for thin disc laser system pump application. On the other hand, low fill factor bars packaged on the same direct copper bonded (DCB) cooling platform are used to build multi-kilowatt direct diode laser systems. We have also optimized the single emitter designs for fiber laser pump applications. In this paper, we will give an overview of our recent advances in high power high brightness laser bars and single emitters for pumping and direct diode application. We will present 300W bar development results for our next generation thin disk laser pump source. We will also show recent improvements on slow axis beam quality of low fill factor bar and its application on performance improvement of 4-5 kW TruDiode laser system with BPP of 30 mm*mrad from a 600 μm fiber. Performance and reliability results of single emitter for multiemitter fiber laser pump source will be presented as well.

Relative elemental abundance and heating constraints determined for the solar corona from SERTS measurements

NASA Technical Reports Server (NTRS)

Falconer, David A.

1994-01-01

Intensities of EUV spectral lines were measured as a function of radius off the solar limb by two flights of Goddard's Solar EUV Rocket Telescope and Spectrograph (SERTS) for three quiet sun regions. The density scale height, line-ratio densities, line-ratio temperatures, and emission measures were determined. The line-ratio temperature determined from the ionization balances of Arnaud and Rothenflug (1985) were more self-consistent than the line-ratio temperatures obtained from the values of Arnaud and Raymond (1992). Limits on the filling factor were determined from the emission measure and the line-ratio densities for all three regions. The relative abundances of silicon, aluminum, and chromium to iron were determined. Results did agree with standard coronal relative elemental abundances for one observation, but did not agree for another. Aluminum was overabundant while silicon was underabundant. Heating was required above 1.15 solar radii for all three regions studied. For two regions, local nonconductive heating is needed for any filling factor, and in all three regions for filling factor of 0.1.

Dental caries and preterm birth: a systematic review and meta-analysis

PubMed Central

D’Antonio, Francesco; Reierth, Eirik; Basnet, Purusotam; Trovik, Tordis A; Orsini, Giovanna; Manzoli, Lamberto; Acharya, Ganesh

2018-01-01

Objectives The primary objective of this systematic review was to evaluate the association between dental caries and preterm birth (PTB). The secondary objective was ascertaining the difference between women with dental caries who experienced PTB and those who did not with regard to decayed, missing and filled teeth (DMFT), and decayed, missing and filled surfaces (DMFS) indices. Methods MEDLINE, Embase, CINAHL and Cochrane databases were searched initially in November 2015 and repeated in December 2016. We included observational cohort and case–control studies. Only studies reporting the risk of PTB in women affected compared with those not affected by dental caries in pregnancy were included. Random-effect meta-analyses were used to compute the summary OR of PTB among women with caries versus women without caries, and the mean difference in either DMFT or DMFS indices between women experiencing PTB and those without PTB. Results Nine observational studies (4826 pregnancies) were included. Women affected by dental caries during pregnancy did not show a significantly higher risk of PTB (OR: 1.16, 95% CI 0.90 to 1.49, P=0.25, I2=35%). Also, the women with PTB did not show significantly higher DMFT or DMFS indices (summary mean differences: 1.56, P=0.10; I2=92% and −0.15, P=0.9, I2=89%, respectively). Conclusion Dental caries does not appear to be a substantial risk factor for PTB. Trial registration number NCT01675180; Pre-results. PMID:29500202

22q11.2 deletion syndrome: behaviour problems of children and adolescents and parental stress.

PubMed

Briegel, W; Schneider, M; Schwab, K Otfried

2008-11-01

22q11.2 deletion syndrome can be associated with a variety of somatic symptoms, developmental delays and psychiatric disorders. At present, there is little information on behaviour problems, parental stress and possible relations between these factors. Therefore, this study investigates behaviour problems of children and adolescents with 22q11.2DS, and their primary caregivers' stress. Parents of 4-17 year old subjects known to the German 22q11.2 deletion syndrome foundation were anonymously asked to fill out several questionnaires, e.g. the Child Behavior Checklist 4-18 (CBCL/4-18). The primary caregivers of 77/126 children [43 males, 34 females, mean age: 8;0 (4;0-16;11) years] sent back filled-out questionnaires. Forty-six of 76 subjects were rated as clinical on at least one of the CBCL-scales. Males had significantly higher scores on the total problems scale and the internalizing problems scale than females. The patients' age correlated with several CBCL-scales. Eleven of 49 subjects were suspicious of an autism spectrum disorder. Compared with the general population, but not with other parents of mentally and/or physically handicapped children, the primary caregivers experienced higher levels of stress, but showed normal life satisfaction. In spite of high rates of clinical behaviour problems among children and adolescents with 22q11.2DS and despite increased parental stress, most primary caregivers seem to have effective coping strategies, e.g. partnership support, to sustain normal levels of life satisfaction.

A comparison of the technological effectiveness of dairy wastewater treatment in anaerobic UASB reactor and anaerobic reactor with an innovative design.

PubMed

Jedrzejewska-Cicinska, M; Kozak, K; Krzemieniewski, M

2007-10-01

The present research was an investigation of the influence of an innovative design of reactor filled with polyethylene (PE) granulate on model dairy wastewater treatment efficiency under anaerobic conditions compared to that obtained in a typical UASB reactor. The experiment was conducted at laboratory scale. An innovative reactor was designed with the reaction chamber inclined 30 degrees in relation to the ground with upward waste flow and was filled with PE granular material. Raw model dairy wastewater was fed to two anaerobic reactors of different design at the organic loading rate of 4 kg COD m(-3)d(-1). Throughout the experiment, a higher removal efficiency of organic compounds was observed in the reactor with an innovative design and it was higher by 7.1% on average than in the UASB reactor. The total suspended solids was lower in the wastewater treated in the anaerobic reactor with the innovative design. Applying a PE granulated filling in the chamber of the innovative reactor contributed to an even distribution of sludge biomass in the reactor, reducing washout of anaerobic sludge biomass from the reaction chamber and giving a higher organic compounds removal efficiency.

Correlation between the dielectric and the mechanical behavior of cellulose nanocomposites extracted from the rachis of the date palm tree

NASA Astrophysics Data System (ADS)

Ladhar, A.; Arous, M.; Kaddami, H.; Ayadi, Z.; Kallel, A.

2017-10-01

In the present study, the dielectric and mechanical properties of natural rubber (NR) based nanocomposites are investigated. Cellulose nanofillers are used in two forms as reinforcing phase: nanofibrillated cellulose (NFC) and cellulose nanocrystals (CNC). In the dielectric study, different relaxation phenomena are detected: the α dipolar relaxation, the lignin and hemicelluloses relaxation, the water dipoles relaxation, the interfacial polarization and the ionic conduction. For the interfacial polarization, the dielectric strength Δε showed lower values for NFC-filled nanocomposites than CNC-filled samples. It was explained with higher interactions between induced dipoles and lower mobility, assuring a better adhesion between the NR and the NFC. Moreover, in tensile tests, the elastic modulus increases with filling indicating the reinforcement effect of nanofillers. In addition, the NR-NFC nanocomposites display the highest tensile modulus. This result shows the higher compatibility of NFC with the NR matrix, and the ensuing higher filler/matrix adhesion. In dynamic mechanical analysis (DMA), a significant reinforcing effect of NFC was shown. This effect is manifested with the high storage modulus E‧, suggesting that the interactions between the NR matrix and the NFC fibers were stronger.

Increased Zn/Glutathione Levels and Higher Superoxide Dismutase-1 Activity as Biomarkers of Oxidative Stress in Women with Long-Term Dental Amalgam Fillings: Correlation between Mercury/Aluminium Levels (in Hair) and Antioxidant Systems in Plasma

PubMed Central

Cabaña-Muñoz, María Eugenia; Parmigiani-Izquierdo, José María; Bravo-González, Luis Alberto; Kyung, Hee-Moon; Merino, José Joaquín

2015-01-01

Background The induction of oxidative stress by Hg can affect antioxidant enzymes. However, epidemiological studies have failed to establish clear association between dental fillings presence and health problems. Objectives To determine whether heavy metals (in hair), antioxidant enzymes (SOD-1) and glutathione levels could be affected by the chronic presence of heavy metals in women who had dental amalgam fillings. Materials and Methods 55 hair samples (42 females with amalgam fillings and 13 female control subjects) were obtained. All subjects (mean age 44 years) who had dental amalgam filling for more than 10 years (average 15 years). Certain metals were quantified by ICP-MS (Mass Spectrophotometry) in hair (μg/g: Al, Hg, Ba, Ag, Sb, As, Be, Bi, Cd, Pb, Pt, Tl, Th, U, Ni, Sn, Ti) and SOD-1 and Glutathione (reduced form) levels in plasma. Data were compared with controls without amalgams, and analyzed to identify any significant relation between metals and the total number of amalgam fillings, comparing those with four or less (n = 27) with those with more than four (n = 15). As no significant differences were detected, the two groups were pooled (Amlgam; n = 42). Findings Hg, Ag, Al and Ba were higher in the amalgam group but without significant differences for most of the heavy metals analyzed. Increased SOD-1 activity and glutathione levels (reduced form) were observed in the amalgam group. Aluminum (Al) correlated with glutathione levels while Hg levels correlated with SOD-1. The observed Al/glutathione and Hg/SOD-1 correlation could be adaptive responses against the chronic presence of mercury. Conclusions Hg, Ag, Al and Ba levels increased in women who had dental amalgam fillings for long periods. Al correlated with glutathione, and Hg with SOD-1. SOD-1 may be a possible biomarker for assessing chronic Hg toxicity. PMID:26076368

Particulate and microbial contamination in in-use admixed intravenous infusions.

PubMed

Yorioka, Katsuhiro; Oie, Shigeharu; Oomaki, Masafumi; Imamura, Akihisa; Kamiya, Akira

2006-11-01

We compared particulate and microbial contamination in residual solutions of peripheral intravenous admixtures after the termination of drip infusion between intravenous fluids admixed with glass ampoule drugs and those admixed with pre-filled syringe drugs. The mean number of particles>or=1.3 microm in diameter per 1 ml of residual solution was 758.4 for fluids (n=60) admixed with potassium chloride in a glass ampoule (20 ml volume), 158.6 for fluids (n=63) admixed with potassium chloride in a pre-filled syringe (20 ml volume), 736.5 for fluids (n=66) admixed with sodium chloride in a glass ampoule (20 ml volume), 179.2 for fluids (n=15) admixed with sodium chloride in a pre-filled syringe (20 ml volume), 1884.5 in fluids (n=30) admixed with dobutamine hydrochloride in 3 glass ampoules (5 ml volume), and 178.9 (n=10) in diluted dobutamine hydrochloride in pre-filled syringes (50 ml volume: For these samples alone, particulate and microbial contamination were evaluated in sealed products.) Thus, for potassium chloride or sodium chloride for injection, the number of particles>or=1.3 microm in diameter in the residual intravenous solution was significantly higher for fluids admixed with glass ampoule drugs than for those admixed with pre-filled syringe drugs (p<0.0001). For dobutamine hydrochloride for injection, the number of particles>or=1.3 microm in diameter in the residual intravenous solution was estimated to be higher for fluids admixed with its glass ampoule drug than for those admixed with its pre-filled syringe drug. Observation of the residual solutions of fluids admixed with potassium chloride, sodium chloride, or dobutamine hydrochloride in glass ampoules using an electron microscope with an X-ray analyzer showed glass fragments in each residual solution. Therefore, for the prevention of glass particle contamination in peripheral intravenous admixtures, the use of pre-filled syringe drugs may a useful method. No microbial contamination was observed in any of the residual solutions of 5 types of admixture.

High 400 °C operation temperature blue spectrum concentration solar junction in GaInN/GaN

DOE Office of Scientific and Technical Information (OSTI.GOV)

Zhao, Liang; Detchprohm, Theeradetch; Wetzel, Christian

2014-12-15

Transparent wide gap junctions suitable as high temperature, high flux topping cells have been achieved in GaInN/GaN by metal-organic vapor phase epitaxy. In structures of 25 quantum wells (QWs) under AM1.5G illumination, an open circuit voltage of 2.1 V is achieved. Of the photons absorbed in the limited spectral range of <450 nm, 64.2% are converted to electrons collected at the contacts under zero bias. At a fill factor of 45%, they account for a power conversion efficiency of38.6%. Under concentration, the maximum output power density per sun increases from 0.49 mW/cm{sup 2} to 0.51 mW/cm{sup 2} at 40 suns and then falls 0.42 mW/cm{sup 2}more » at 150 suns. Under external heating, a maximum of 0.59 mW/cm{sup 2} is reached at 250 °C. Even at 400 °C, the device is fully operational and exceeds room temperature performance. A defect analysis suggests that significantly higher fill factors and extension into longer wavelength ranges are possible with further development. The results prove GaInN/GaN QW solar junctions a viable and rugged topping cell for concentrator photovoltaics with minimal cooling requirements. By capturing the short range spectrum, they reduce the thermal load to any conventional cells stacked behind.« less

Fusion: ultra-high-speed and IR image sensors

NASA Astrophysics Data System (ADS)

Etoh, T. Goji; Dao, V. T. S.; Nguyen, Quang A.; Kimata, M.

2015-08-01

Most targets of ultra-high-speed video cameras operating at more than 1 Mfps, such as combustion, crack propagation, collision, plasma, spark discharge, an air bag at a car accident and a tire under a sudden brake, generate sudden heat. Researchers in these fields require tools to measure the high-speed motion and heat simultaneously. Ultra-high frame rate imaging is achieved by an in-situ storage image sensor. Each pixel of the sensor is equipped with multiple memory elements to record a series of image signals simultaneously at all pixels. Image signals stored in each pixel are read out after an image capturing operation. In 2002, we developed an in-situ storage image sensor operating at 1 Mfps 1). However, the fill factor of the sensor was only 15% due to a light shield covering the wide in-situ storage area. Therefore, in 2011, we developed a backside illuminated (BSI) in-situ storage image sensor to increase the sensitivity with 100% fill factor and a very high quantum efficiency 2). The sensor also achieved a much higher frame rate,16.7 Mfps, thanks to the wiring on the front side with more freedom 3). The BSI structure has another advantage that it has less difficulties in attaching an additional layer on the backside, such as scintillators. This paper proposes development of an ultra-high-speed IR image sensor in combination of advanced nano-technologies for IR imaging and the in-situ storage technology for ultra-highspeed imaging with discussion on issues in the integration.

Solution-processed small molecule:fullerene bulk-heterojunction solar cells: impedance spectroscopy deduced bulk and interfacial limits to fill-factors.

PubMed

Guerrero, Antonio; Loser, Stephen; Garcia-Belmonte, Germà; Bruns, Carson J; Smith, Jeremy; Miyauchi, Hiroyuki; Stupp, Samuel I; Bisquert, Juan; Marks, Tobin J

2013-10-21

Using impedance spectroscopy, we demonstrate that the low fill factor (FF) typically observed in small molecule solar cells is due to hindered carrier transport through the active layer and hindered charge transfer through the anode interfacial layer (IFL). By carefully tuning the active layer thickness and anode IFL in BDT(TDPP)2 solar cells, the FF is increased from 33 to 55% and the PCE from 1.9 to 3.8%. These results underscore the importance of simultaneously optimizing active layer thickness and IFL in small molecule solar cells.

Analysis of photonic band gap in novel piezoelectric photonic crystal

NASA Astrophysics Data System (ADS)

Malar Kodi, A.; Doni Pon, V.; Joseph Wilson, K. S.

2018-03-01

The transmission properties of one-dimensional novel photonic crystal having silver-doped novel piezoelectric superlattice and air as the two constituent layers have been investigated by means of transfer matrix method. By changing the appropriate thickness of the layers and filling factor of nanocomposite system, the variation in the photonic band gap can be studied. It is found that the photonic band gap increases with the filling factor of the metal nanocomposite and with the thickness of the layer. These structures possess unique characteristics enabling one to operate as optical waveguides, selective filters, optical switches, integrated piezoelectric microactuators, etc.

Prospect of the high efficiency for the VEST (Via-hole Etching for the Separation of Thin films) cell

DOE Office of Scientific and Technical Information (OSTI.GOV)

Deguchi, M.; Kawama, Y.; Matsuno, Y.

1994-12-31

The optimum design of the via-holes for the VEST cell was studied. Using a simple model, fill factors of the VEST cell were calculated. As for the via-hole distribution pattern, square grid pattern was found to be most suitable from the view points of the cell performance and the easiness of the electrode designing. It was found that the fill factor large enough (> 0.79) for the high efficiency can be obtained. A fabricated test cell showed the efficiency of 14.4%. Further improvement (efficiency over 18%) is possibly expected.

Epidemiology of general obesity, abdominal obesity and related risk factors in urban adults from 33 communities of northeast china: the CHPSNE study

PubMed Central

2012-01-01

Background Obesity increases the risk of many diseases. However, there has been little literature about the epidemiology of obesity classified by body mass index (BMI) or waist (abdominal obesity) among urban Chinese adults. This study is to fill the gap by assessing the prevalence of obesity and associated risk factors among urban Chinese adults. Methods A representative sample of 25,196 urban adults aged 18 to 74 years in Northeast China was selected and measurements of height, weight and waist circumference (WC) were taken from 2009–2010. Definitions of overweight and obesity by the World Health Organization (WHO) were used. Results The overall prevalence rates of general obesity and overweight classified by BMI were 15.0% (15.7% for men and 14.3% for women, p<0.01) and 19.2% (20.8% for men and 17.7% for women, p<0.01), respectively, and the overall prevalence rate of abdominal obesity was 37.6% (31.1% for men and women 43.9% for women, p<0.01). Multivariable logistic regression showed that the elderly and those who had a history of parental obesity, alcohol drinking, or former cigarette smoking were at high risk of obesity classified by BMI or WC, whereas those with a higher level of education, higher family income, or a healthy and balanced diet were at low risk of obesity. Analysis stratified by gender showed that men with a higher level education level, a white-collar job, a cadre job, or higher family income were the high risk group, and women with a higher level of education or higher family income were the low risk group. Conclusions Obesity and overweight have become epidemic in urban populations in China; associations of risk factors with obesity differ between men and women. PMID:23146089

Salivary bisphenol A levels and their association with composite resin restoration.

PubMed

Lee, Jung-Ha; Yi, Seung-Kyoo; Kim, Se-Yeon; Kim, Ji-Soo; Son, Sung-Ae; Jeong, Seung-Hwa; Kim, Jin-Bom

2017-04-01

Composite resin has been increasingly used in an effort to remove minimal amount of tooth structure and are used for restoring not just carious cavities but also cervical abrasion. To synthesize composite resin, bisphenol A (BPA) is used. The aim of the study was to measure the changes in salivary BPA level related with composite resin restoration. ELISA was used to examine the BPA levels in the saliva collected from 30 volunteers whose teeth were filled with composite resin. Salivary samples were collected immediately before filling and 5 min and 7 d after filling. Wilcoxon signed-ranks test and linear regression were performed to test the significant differences of the changes in BPA levels in saliva. Before a new composite resin filling, there was no significant difference between with and without existing filling of composite resin and BPA level in the saliva was not correlated to the number of filled surfaces with composite resin. However, BPA level in the saliva increased to average 3.64 μg/L from average 0.15 μg/L after filling 5 min. BPA level increased in proportion with the number of filled surfaces. BPA level decreased to average 0.59 after filling 7 d. However it was higher than the BPA level before a new composite resin filling. Considering 50 μg/kg/day as the Tolerable Daily Intake of BPA suggested by European Food Safety Authority, the amount of BPA eluted in saliva after the composite resin filling is considered a safe level that is not a hazard to health at all. Copyright © 2016 Elsevier Ltd. All rights reserved.

Intraoperative assessment of intraocular pressure in vitrectomized air-filled and fluid-filled eyes.

PubMed

Moon, Chan Hee; Choi, Kyung Seek; Rhee, Mi Ri; Lee, Sung Jin

2013-11-01

To ascertain the difference of intraocular pressure (IOP) measurement between vitrectomized air-filled and fluid-filled eyes. Thirty-one eyes of 31 consecutive patients who underwent conventional vitrectomy and intraocular gas tamponade were assessed. After vitrectomy, IOP of the fluid-filled eyes was measured by Tono-Pen. Thereafter, fluid-air exchange was performed, and IOP of the air-filled eyes was measured again. The IOP within each fluid- and air-filled eye was varied by selecting settings on the vitrectomy system, from 10 to 50 mmHg with 5-mmHg increments. Postoperatively, IOP was assessed by both Tono-Pen and Goldmann applanation tonometry (GAT). Linear and nonlinear regression analyses were conducted between intraoperatively measured Tono-Pen readings and actual IOPs. Bland-Altman plot was used to assess the agreements between postoperatively measured Tono-Pen readings and GAT readings. The discrepancy between Tono-Pen readings and actual IOP in fluid-filled eyes was not significant, except for the profound high pressures over 45 mmHg. However, Tono-Pen readings in air-filled eyes were significantly lower than actual IOPs in all ranges, and Tono-Pen increasingly underestimates IOP at higher levels. Intraoperative Tono-Pen readings were correlated significantly with actual IOP and a quadratic equation evidenced the best fit (R(2) = 0.996). Postoperatively, difference of the measurements between Tono-Pen and GAT was not significant. Tono-Pen and GAT significantly underestimate actual IOP in air-filled eyes. It should be considered that actual IOP would be greater than the measured IOP in gas-filled eyes, even though the IOP is measured as normal. © 2013 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Burnout and Associated Factors among Iranian Emergency Medicine Practitioners

PubMed Central

JALILI, Mohammad; SADEGHIPOUR ROODSARI, Gholamreza; BASSIR NIA, Anahita

2013-01-01

Abstract Background Emergency physicians are at risk of burnout, which can affect their mental health, as well as patient care. We assessed burnout level among Iranian emergency physicians and investigated demographic, work-related factors and stressors associated with higher burnout. Methods In a cross-sectional study, we surveyed all 188 emergency medicine residents and practitioners in Iran. We measured burnout using 22-item Maslach Burnout Inventory assessing emotional exhaustion, depersonalization and personal accomplishment, also demographic factors, work related factors and sources of stress in emergency department using anonymous self-administered questionnaire. Descriptive analysis, univariate analysis to evaluate association with higher score of burnout, and multivariate logistic regression analysis to predict high burnout in 3 subscales was performed. Results Totally, 165 questionnaires were filled (response rate: 88%; mean age: 33.6 years, 91% male). Mean burnout scores were 22.94 for emotional exhaustion (95% CI=20.78-25.01; moderate), 9.3 for depersonalization (95% CI=8.24-10.36; moderate to high), and 31.47 for personal accomplishment (95% CI=29.87-33.07; moderate to high). Frequent reported sources of stress were shortage of equipment, problem with work physical environment, and relationship with other services. All 19 sources of stress were associated with higher score of emotional exhaustion and depersonalization; while twelve out of 19 were significantly associated with lower level of personal accomplishment. In logistic regression model, the significant predictors for high emotional exhaustion were work overload, feeling of insecurity for future career and difficulties to balance professional and private life. Conclusion Burnout is high among Iranian emergency medicine practitioners and some interventions can be proposed to reduce stress. PMID:26060665

Detection of sulfur in the galactic center

NASA Technical Reports Server (NTRS)

Herter, T.; Briotta, D. A., Jr.; Gull, G. E.; Shure, M. A.; Houck, J. R.

1983-01-01

A strong detection at the S III forbidden 18.71 micron line is reported for the galactic center region, Sgr A West. A line flux of 1.7 + or - 0.2 x 10 to the -17th W/sq cm is found for a 20 inch beam size measurement centered on IRS 1. A preliminary analysis indicates that the S III abundance relative to hydrogen is consistent with the cosmic abundance of sulfur, 0.000016, if a filling factor of unity within the known clumps is assumed. However, the sulfur abundance in the galactic center may be as much as a factor of 3 overabundant if a filling factor of 0.03 is adopted, a value found to hold for some galactic H II regions.

Chemistry and petrography of calcite in the KTB pilot borehole, Bavarian Oberpfalz, Germany

USGS Publications Warehouse

Komor, S.C.

1995-01-01

The KTB pilot borehole in northeast Bavaria, Germany, penetrates 4000 m of gneiss, amphibolite, and subordinate calc-silicate, lamprophyre and metagabbro. There are three types of calcite in the drilled section: 1) metamorphic calcite in calc-silicate and marble; 2) crack-filling calcite in all lithologies; and 3) replacement calcite in altered minerals. Crack-filling and replacement calcite postdate metamorphic calcite. Multiple calcite generations in individual cracks suggest that different generations of water repeatedly flowed through the same cracks. Crack-filling mineral assemblages that include calcite originally formed at temperatures of 150-350??C. Presently, crack-filling calcite is in chemical and isotopic equilibrium with saline to brackish water in the borehole at temperatures of ???120??C. The saline to brackish water contains a significant proportion of meteoric water. Re-equilibration of crack-filling calcite to lower temperatures means that calcite chemistry tells us little about water-rock interactions in the crystal section of temperatures higher than ~120??C. -from Author

A survey of water activity and pH values in fresh pasta packed under modified atmosphere manufactured in Argentina and Uruguay.

PubMed

Schebor, C; Chirife, J

2000-07-01

The water activity (a(w)) and pH values of commercially available filled fresh pasta and gnocchi packed under modified atmosphere and manufactured in Argentina and Uruguay were examined. The retail survey included 58 samples (several brands) of filled pasta and 11 samples of gnocchi. Fillings consisted of different combinations of cheese (various types), beef, ricotta, ham, chicken, and spinach. The survey revealed that the a(w) values of the 58 samples of filled pasta ranged from 0.916 to 0.973, and their pH values ranged from 5.2 to 7.0. The a(w) of gnocchi was consistently higher and ranged from 0.936 to 0.983, with pH values from 4.8 to 6.4. Some samples of filled pasta and most gnocchi samples were found to have a(w) and pH values that would support growth of spores of Clostridium botulinum, if present, under conditions of temperature abuse (i.e., 30 degrees C).

Critical temperature of noninteracting bosonic gases in cubic optical lattices at arbitrary integer fillings.

PubMed

Rakhimov, Abdulla; Askerzade, Iman N

2014-09-01

We have shown that the critical temperature of a Bose-Einstein condensate to a normal phase transition of noninteracting bosons in cubic optical lattices has a linear dependence on the filling factor, especially at large densities. The condensed fraction exhibits a linear power law dependence on temperature in contrast to the case of ideal homogeneous Bose gases.

High-density carbon (HDC) capsule designs for α-heating and for ignition

NASA Astrophysics Data System (ADS)

Ho, D.; Amendt, A.; Clark, D.; Haan, S.; Milovich, J.; Salmonson, J.; Zimmerman, G.; Berzak Hopkins, L.; Biener, J.; Meezan, N.; Thomas, C.; Benedict, L.; Le Pape, S.; MacKinnon, A.; Ross, S.

2014-10-01

We show capsule designs that have HDC ablators, using 2, 3 and 4 shocks. Their advantages and disadvantages will be discussed. Two-shock designs have the shortest pulse length but have the worst 1-D ignition margin because of the high fuel adiabat. Four-shock designs have the highest 1-D ignition margin with the lowest adiabat, but have higher RT ablation front growth. This disadvantage can be overcome by using a picket to generate the 1st shock. The picket reduces the RT growth factor while the decaying 1st shock lowers the fuel adiabat further. The picket has the additional advantage of shortening the pulse length. Dopant requirements for different hohlraums will be discussed. A 3-shock design for achieving alpha heating is described, which can use either high-gas-fill (1.6 mg/cc) or near-vacuum hohlraums. A rugby-shaped hohlraum with low gas-fill (0.5 mg/cc) has high laser coupling efficiency and provides good symmetry for a 4-shock design. Comparison of simulations for selected recent HDC shots with experimental data will be presented. Prepared by LLNL under Contract DE-AC52-07NA27344.

GLASS TRANSITION AND DEGREE OF CONVERSION OF A LIGHT-CURED ORTHODONTIC COMPOSITE

PubMed Central

Sostena, Michela M. D. S.; Nogueira, Renata A.; Grandini, Carlos R.; Moraes, João Carlos Silos

2009-01-01

Objective: This study evaluated the glass transition temperature (Tg) and degree of conversion (DC) of a light-cured (Fill Magic) versus a chemically cured (Concise) orthodontic composite. Material and Methods: Anelastic relaxation spectroscopy was used for the first time to determine the Tg of a dental composite, while the DC was evaluated by infrared spectroscopy. The light-cured composite specimens were irradiated with a commercial LED light-curing unit using different exposure times (40, 90 and 120 s). Results: Fill Magic presented lower Tg than Concise (35-84°C versus 135°C), but reached a higher DC. Conclusions: The results of this study suggest that Fill Magic has lower Tg than Concise due to its higher organic phase content, and that when this light-cured composite is used to bond orthodontic brackets, a minimum energy density of 7.8 J/cm2 is necessary to reach adequate conversion level and obtain satisfactory adhesion. PMID:20027428

Method and apparatus for producing gas-filled hollow spheres. [target pellets for inertial confinement fusion

NASA Technical Reports Server (NTRS)

Wang, T. G.; Elleman, D. D. (Inventor)

1982-01-01

A system for forming hollow spheres containing pressured gas is described which includes a cylinder device containing a molten solid material with a nozzle at its end. A second gas nozzle, lying slightly upstream from the tip of the first nozzle, is connected to a source that applies pressured filler gas that is to fill the hollow spheres. High pressure is applied to the molten metal, as by moving a piston within the cylinder device, to force the molten material out of the first nozzle. At the same time, pressured gas fills the center of the extruded hollow liquid pipe that breaks into hollow spheres. The environment outside the nozzles contains gas at a high pressure such as 100 atmospheres. Gas is supplied to the gas nozzle at a slightly higher pressure such as 101 atmospheres. The pressure applied to the molten material is at a still higher pressure such as 110 atmospheres.

Solubility of a new calcium silicate-based root-end filling material

PubMed Central

Singh, Shishir; Podar, Rajesh; Dadu, Shifali; Kulkarni, Gaurav; Purba, Rucheet

2015-01-01

Introduction: The purpose of this study was to compare solubility of a new calcium silicate-based cement, Biodentine with three commonly used root-end filling materials viz. glass-ionomer cement (GIC), intermediate restorative material (IRM), and mineral trioxide aggregate (MTA). Materials and Methods: Twenty stainless steel ring molds were filled with cements corresponding to four groups (n = 5). The weight of 20 dried glass bottles was recorded. Samples were transferred to bottles containing 5 ml of distilled water and stored for 24 h. The bottles were dried at 105΀C and weighed. This procedure was repeated for 3, 10, 30, and 60 days. Data was analyzed with one-way analysis of variance (ANOVA) test (P < 0.05). Results: Biodentine demonstrated significantly higher solubility than MTA for 30- and 60-day immersion periods. Statistical difference was noted between the solubility values of Biodentine samples amongst each of the five time intervals. Conclusions: Biodentine exhibited higher solubility in comparison with all other cements. PMID:25829696

The characteristics of extracellular polymeric substances and soluble microbial products in moving bed biofilm reactor-membrane bioreactor.

PubMed

Duan, Liang; Jiang, Wei; Song, Yonghui; Xia, Siqing; Hermanowicz, Slawomir W

2013-11-01

The characteristics of extracellular polymeric substances (EPS) and soluble microbial products (SMP) in conventional membrane bioreactor (MBR) and in moving bed biofilm reactor-membrane bioreactors (MBBR-MBR) were investigated in long-term (170 days) experiments. The results showed that all reactors had high removal efficiency of ammonium and COD, despite very different fouling conditions. The MBBR-MBR with media fill ratio of 26.7% had much lower total membrane resistance and no obvious fouling were detected during the whole operation. In contrast, MBR and MBBR-MBR with lower and higher media fill experienced more significant fouling. Low fouling at optimum fill ratio may be due to the higher percentage of small molecular size (<1 kDa) and lower percentage of large molecular size (>100 kDa) of EPS and SMP in the reactor. The composition of EPS and SMP affected fouling due to different O-H bonds in hydroxyl functional groups, and less polysaccharides and lipids. Copyright © 2013 Elsevier Ltd. All rights reserved.

Interfacial and Mechanical Behavior of AA5456 Filling Friction-Stir-Welded Lap Joints Using Similar and Dissimilar Pins

NASA Astrophysics Data System (ADS)

Behmand, Saleh Alaei; Mirsalehi, Seyyed Ehsan; Omidvar, Hamid; Safarkhanian, Mohammad Ali

2016-10-01

In this article, filling friction stir welding (FFSW) of the remaining exit holes of AA5456 alloy friction-stir-welded lap joints was studied. For this purpose, the influences of different rotating speeds, holding times, and pin materials, AA5456 and AA2024, on the metallurgical structure and joint strength were investigated. The observations showed that defect-free lap joints are successfully obtainable by this method using similar and dissimilar consumable pins. The results indicated that the higher rotating speed and holding time adversely affect the weld performance. The best result was achieved for 30 seconds holding time, 500 rpm rotating speed, and AA2024 consumable pin. In this condition, a lap shear strength of 10 pct higher than that of the nonfilled joint, equivalent to about 94 pct of the original defect-free FSW joint, was obtained, whereas the GTAW filled joint showed only approximately 87 pct of the continuous FSW joint strength.

Comparative studies on the mechanical properties of natural rubber and natural rubber filled with multi-walled carbon nanotubes

NASA Astrophysics Data System (ADS)

Ismail, R.; Ibrahim, A.; Rusop, M.; Adnan, A.

2018-05-01

The present article compares the mechanical properties of natural rubber (NR) and carbon nanotubes (CNTs) filled natural rubber composites. Four types of nanocomposite specimens are fabricated with different MWCNT loadings: 0 wt% (pure natural rubber), 1 wt%, 3 wt%, and 5 wt%. The specimens are tested for their mechanical properties. It is observed that the tensile strength, hardness and elongation break of CNTs filled rubber composites are remarkably higher than that of raw rubber indicating the inherent reinforcing potential of CNTs. Percentage of the elongation at break of rubber CNTs composites is lower than that of raw rubber.

Microtensile bond strength of bulk-fill restorative composites to dentin.

PubMed

Mandava, Jyothi; Vegesna, Divya-Prasanna; Ravi, Ravichandra; Boddeda, Mohan-Rao; Uppalapati, Lakshman-Varma; Ghazanfaruddin, M D

2017-08-01

To facilitate the easier placement of direct resin composite in deeper cavities, bulk fill composites have been introduced. The Mechanical stability of fillings in stress bearing areas restored with bulk-fill resin composites is still open to question, since long term clinical studies are not available so far. Thus, the objective of the study was to evaluate and compare the microtensile bond strength of three bulk-fill restorative composites with a nanohybrid composite. Class I cavities were prepared on sixty extracted mandibular molars. Teeth were divided into 4 groups (n= 15 each) and in group I, the prepared cavities were restored with nanohybrid (Filtek Z250 XT) restorative composite in an incremental manner. In group II, III and IV, the bulk-fill composites (Filtek, Tetric EvoCeram, X-tra fil bulk-fill restoratives) were placed as a 4 mm single increment and light cured. The restored teeth were subjected to thermocycling and bond strength testing was done using instron testing machine. The mode of failure was assessed by scanning electron microscope (SEM). The bond strength values obtained in megapascals (MPa) were subjected to statistical analysis, using SPSS/PC version 20 software.One-way ANOVA was used for groupwise comparison of the bond strength. Tukey's Post Hoc test was used for pairwise comparisons among the groups. The highest mean bond strength was achieved with Filtek bulk-fill restorative showing statistically significant difference with Tetric EvoCeram bulk-fill ( p < 0.003) and X-tra fil bulk-fill ( p <0.001) composites. Adhesive failures are mostly observed with X-tra fil bulk fill composites, whereas mixed failures are more common with other bulk fill composites. Bulk-fill composites exhibited adequate bond strength to dentin and can be considered as restorative material of choice in posterior stress bearing areas. Key words: Bond strength, Bulk-fill restoratives, Configuration factor, Polymerization shrinkage.

It's my party and I eat if I want to. Reasons for unhealthy snacking.

PubMed

Verhoeven, Aukje A C; Adriaanse, Marieke A; de Vet, Emely; Fennis, Bob M; de Ridder, Denise T D

2015-01-01

Investigating the reasons that people give for unhealthy snacking behavior is important for developing effective health interventions. Little research, however, has identified reasons that apply to a large audience and most studies do not integrate multiple factors, precluding any conclusions regarding their relative importance. The present study explored reasons for unhealthy snacking among a representative community sample. Participants (N = 1544) filled out the newly developed Reasons to Snack inventory assessing an elaborate range of motives at baseline and 1-month follow-up. Exploratory and replication factor analyses identified six categories: opportunity induced eating, coping with negative emotions, enjoying a special occasion, rewarding oneself, social pressure, and gaining energy. The highest mean scores were obtained for enjoying a special occasion and opportunity induced eating. Regression analyses with participant characteristics as independent variables and each category of reasons as dependent variables showed differences for age. For all reasons except to enjoy a special occasion, younger people reported a higher score. Women indicated a higher score than men on coping with negative emotions, enjoying a special occasion and gaining energy. People who diet to a stronger extent reported a higher score for snacking because of social pressure, to reward oneself and to cope with negative emotions, with the latter also being related to a higher BMI. Finally, a higher education was associated with enjoying a special occasion. Future health interventions could allocate more attention to diminishing unhealthy snacking with regard to the six identified categories, specifically focusing on enjoying a special occasion and opportunity induced eating. Copyright © 2014 Elsevier Ltd. All rights reserved.

Neural representation of form-contingent color filling-in in the early visual cortex.

PubMed

Hong, Sang Wook; Tong, Frank

2017-11-01

Perceptual filling-in exemplifies the constructive nature of visual processing. Color, a prominent surface property of visual objects, can appear to spread to neighboring areas that lack any color. We investigated cortical responses to a color filling-in illusion that effectively dissociates perceived color from the retinal input (van Lier, Vergeer, & Anstis, 2009). Observers adapted to a star-shaped stimulus with alternating red- and cyan-colored points to elicit a complementary afterimage. By presenting an achromatic outline that enclosed one of the two afterimage colors, perceptual filling-in of that color was induced in the unadapted central region. Visual cortical activity was monitored with fMRI, and analyzed using multivariate pattern analysis. Activity patterns in early visual areas (V1-V4) reliably distinguished between the two color-induced filled-in conditions, but only higher extrastriate visual areas showed the predicted correspondence with color perception. Activity patterns allowed for reliable generalization between filled-in colors and physical presentations of perceptually matched colors in areas V3 and V4, but not in earlier visual areas. These findings suggest that the perception of filled-in surface color likely requires more extensive processing by extrastriate visual areas, in order for the neural representation of surface color to become aligned with perceptually matched real colors.

Are the measurements of water-filled and air-charged catheters the same in urodynamics?

PubMed

Digesu, G Alessandro; Derpapas, Alexandros; Robshaw, Penny; Vijaya, Gopalan; Hendricken, Caroline; Khullar, Vik

2014-01-01

The aim of our study was to compare air-charged and water-filled catheters simultaneously in the measurement of the intravesical, abdominal and detrusor pressure during urodynamic investigations. Consecutive women with lower urinary tract symptoms, referred for urodynamics were prospectively studied. Readings of intravesical pressure (p(ves)), abdominal pressure (p(abd)) and detrusor pressure (p(det)), recorded by both the air-charged and water-filled catheters, were displayed simultaneously and compared at the end of filling, on standing, on sitting prior to voiding and at the maximum involuntary detrusor contraction. The signals (pressures) recorded by both types of catheter were compared using the Bland-Altman plot and paired samples t test. Twenty women with a mean age of 49 (range 36-72) were recruited. One patient with normal urodynamics was excluded in view of the poor quality trace. At each of the four comparison points, the air-charged catheters consistently produced higher mean pressures than the water-filled catheters. There were wide variations in the difference between the readings produced by the two types of catheter. Pressures measured using air-charged catheters are not comparable with water-filled catheters and are therefore not interchangeable. Caution must be used when comparing urodynamic parameters using air-charged and water-filled catheters.

Pediatric prescription pick-up rates after ED visits.

PubMed

Kajioka, Eric H; Itoman, Erick M; Li, M Lily; Taira, Deborah A; Li, Gaylyn G; Yamamoto, Loren G

2005-07-01

To determine the compliance rate in filling outpatient medication prescriptions written upon discharge from the emergency department (ED). Emergency department records of children during a 3-month period were examined along with pharmacy claim data obtained in cooperation with the largest insurance carrier in the community (private and Medicaid). Pharmacy claim data were used to validate the prescription pick-up date. Overall, 65% of high-urgency prescriptions were filled. The prescription pick-up rate in the 0-to 3-year age group (75%) was significantly higher than in the rest of the cohort (55%) ( P < .001). Children with private insurance were more likely to fill their prescriptions (68%) compared to children with Medicaid insurance (57%) ( P = .03). This study demonstrates that filling a prescription after discharge from an ED represents a substantial barrier to medication compliance.

Arab Women Make Inroads in Higher Education but Often Find Dead Ends

ERIC Educational Resources Information Center

Lindsey, Ursula

2012-01-01

Since at least the early 1990s, Arab governments have made women's participation in higher education a priority. Across the region, young women fill the crowded lecture halls and bustling courtyards of universities. On many campuses, they outnumber men. But women's increased participation in higher education does not necessarily translate into…

Democratic Reforms and Women's Higher Education during the U.S. Occupation of Japan, 1945-1952.

ERIC Educational Resources Information Center

Moroishi, Yasumi; Martin, Don T.

This paper aims to show the significance of the educational reforms of women's higher education during the U.S. occupation of post-World War II Japan. To help fill the gap of research on women's higher education in Japan, focus is on an historical analysis of women's higher education reform policies. Since educational reforms are not…

The relationship between gas fill density and hohlraum drive performance at the National Ignition Facility

NASA Astrophysics Data System (ADS)

Hall, G. N.; Jones, O. S.; Strozzi, D. J.; Moody, J. D.; Turnbull, D.; Ralph, J.; Michel, P. A.; Hohenberger, M.; Moore, A. S.; Landen, O. L.; Divol, L.; Bradley, D. K.; Hinkel, D. E.; Mackinnon, A. J.; Town, R. P. J.; Meezan, N. B.; Berzak Hopkins, L.; Izumi, N.

2017-05-01

Indirect drive inertial confinement fusion experiments were conducted at the National Ignition Facility to investigate the performance of the hohlraum drive as a function of hohlraum gas fill density by imploding high-density-carbon capsules using a 2-shock laser pulse. Measurements characterized the backscatter behavior, the production of hot electrons, the motion and brightness of the laser spots on the hohlraum wall, and the efficiency of the hohlraum x-ray drive as a function of gas fill density ρgf between 0.03 mg/cc ("near vacuum") and 1.6 mg/cc. For hohlraums with ρgf up to 0.85 mg/cc, very little stimulated Raman backscatter (SRS) was observed. For higher ρgf, significant SRS was produced and was observed to occur during the rise to peak laser power and throughout the main pulse. The efficiency with which laser energy absorbed by the hohlraum is converted into drive energy was measured to be the same for ρgf ≥ 0.6 mg/cc once the laser reached peak power. However, for the near vacuum case, the absorbed energy was converted to drive energy more efficiently throughout the pulse and maintained an efficiency ˜10% higher than the gas filled hohlraums throughout the main pulse.

The relationship between gas fill density and hohlraum drive performance at the National Ignition Facility

DOE Office of Scientific and Technical Information (OSTI.GOV)

Hall, G. N.; Jones, O. S.; Strozzi, D. J.

Indirect drive inertial confinement fusion experiments were conducted at the National Ignition Facility to investigate the performance of the hohlraum drive as a function of hohlraum gas fill density by imploding high-density-carbon capsules using a 2-shock laser pulse. Our ,easurements characterize the backscatter behavior, the production of hot electrons, the motion and brightness of the laser spots on the hohlraum wall, and the efficiency of the hohlraum x-ray drive as a function of gas fill density ρ gf between 0.03 mg/cc (“near vacuum”) and 1.6 mg/cc. For hohlraums with ρ gf up to 0.85 mg/cc, very little stimulated Raman backscattermore » (SRS) was observed. Furthermore, for higher ρ gf, significant SRS was produced and was observed to occur during the rise to peak laser power and throughout the main pulse. The efficiency with which laser energy absorbed by the hohlraum is converted into drive energy was measured to be the same for ρ gf ≥ 0.6 mg/cc once the laser reached peak power. But, for the near vacuum case, the absorbed energy was converted to drive energy more efficiently throughout the pulse and maintained an efficiency ~10% higher than the gas filled hohlraums throughout the main pulse.« less

The relationship between gas fill density and hohlraum drive performance at the National Ignition Facility

DOE PAGES

Hall, G. N.; Jones, O. S.; Strozzi, D. J.; ...

2017-05-11

Indirect drive inertial confinement fusion experiments were conducted at the National Ignition Facility to investigate the performance of the hohlraum drive as a function of hohlraum gas fill density by imploding high-density-carbon capsules using a 2-shock laser pulse. Our ,easurements characterize the backscatter behavior, the production of hot electrons, the motion and brightness of the laser spots on the hohlraum wall, and the efficiency of the hohlraum x-ray drive as a function of gas fill density ρ gf between 0.03 mg/cc (“near vacuum”) and 1.6 mg/cc. For hohlraums with ρ gf up to 0.85 mg/cc, very little stimulated Raman backscattermore » (SRS) was observed. Furthermore, for higher ρ gf, significant SRS was produced and was observed to occur during the rise to peak laser power and throughout the main pulse. The efficiency with which laser energy absorbed by the hohlraum is converted into drive energy was measured to be the same for ρ gf ≥ 0.6 mg/cc once the laser reached peak power. But, for the near vacuum case, the absorbed energy was converted to drive energy more efficiently throughout the pulse and maintained an efficiency ~10% higher than the gas filled hohlraums throughout the main pulse.« less

The demand for doctorally prepared public health personnel in institutions of higher education.

PubMed

Scutchfield, F D; Quimson, S; Williams, S J; Hofstetter, R

1988-01-01

We examined the demand for doctorally prepared public health personnel in academia. We developed an unduplicated list of positions advertised during 1983 in several of the nation's public health journals. Based on this, we identified a total of 217 available positions. We surveyed the persons who placed the advertisements regarding their perceptions of the applicant pool, their experiences in filling the positions, and their perceptions of the future supply of doctorally prepared public health personnel. Of the respondents, 93% were in institutions of higher education. Based on their response, it appears that the current supply of doctorally prepared public health personnel is short and is likely to continue to be limited. Respondents had difficulty filling the advertised positions, based on the amount of time necessary to fill the position, and a number of positions had to be modified in order to be filled. Thirty-two percent of the respondents replied that the pool of applicants was low or poor. Thirty-four percent felt there was a shortage of such personnel, and a similar percentage felt there would be a future shortage. Based on our data, we believe that there is now a shortage of doctorally educated public health personnel for academic positions and that this shortage is likely to continue.

Molar cusp deformation evaluated by micro-CT and enamel crack formation to compare incremental and bulk-filling techniques.

PubMed

Oliveira, Laís Rani Sales; Braga, Stella Sueli Lourenço; Bicalho, Aline Arêdes; Ribeiro, Maria Tereza Hordones; Price, Richard Bengt; Soares, Carlos José

2018-07-01

To describe a method of measuring the molar cusp deformation using micro-computed tomography (micro-CT), the propagation of enamel cracks using transillumination, and the effects of hygroscopic expansion after incremental and bulk-filling resin composite restorations. Twenty human molars received standardized Class II mesio-occlusal-distal cavity preparations. They were restored with either a bulk-fill resin composite, X-tra fil (XTRA), or a conventional resin composite, Filtek Z100 (Z100). The resin composites were tested for post-gel shrinkage using a strain gauge method. Cusp deformation (CD) was evaluated using the images obtained using a micro-CT protocol and using a strain-gauge method. Enamel cracks were detected using transillumination. The post-gel shrinkage of Z100 was higher than XTRA (P < 0.001). The amount of cusp deformation produced using Z100 was higher compared to XTRA, irrespective of the measurement method used (P < 0.001). The thinner lingual cusp always had a higher CD than the buccal cusp, irrespective of the measurement method (P < 0.001). A positive correlation (r = 0.78) was found between cusp deformation measured by micro-CT or by the strain-gauge method. After hygroscopic expansion of the resin composite, the cusp displacement recovered around 85% (P < 0.001). After restoration, Z100 produced more cracks than XTRA (P = 0.012). Micro-CT was an effective method for evaluating the cusp deformation. Transillumination was effective for detecting enamel cracks. There were fewer negative effects of polymerization shrinkage in bulk-fill resin restorations using XTRA than for the conventional incremental filling technique using conventional composite resin Z100. Shrinkage and cusp deformation are directly related to the formation of enamel cracks. Cusp deformation and crack propagation may increase the risk of tooth fracture. Copyright © 2018 Elsevier Ltd. All rights reserved.

Composite fermions on a torus

NASA Astrophysics Data System (ADS)

Pu, Songyang; Wu, Ying-Hai; Jain, J. K.

2017-11-01

We achieve an explicit construction of the lowest Landau level (LLL) projected wave functions for composite fermions in the periodic (torus) geometry. To this end, we first demonstrate how the vortex attachment of the composite fermion (CF) theory can be accomplished in the torus geometry to produce the "unprojected" wave functions satisfying the correct (quasi)periodic boundary conditions. We then consider two methods for projecting these wave functions into the LLL. The direct projection produces valid wave functions but can be implemented only for very small systems. The more powerful and more useful projection method of Jain and Kamilla fails in the torus geometry because it does not preserve the periodic boundary conditions and thus takes us out of the original Hilbert space. We have succeeded in constructing a modified projection method that is consistent with both the periodic boundary conditions and the general structure of the CF theory. This method is valid for a large class of states of composite fermions, called "proper states," which includes the incompressible ground states at electron filling factors ν =n/2 p n +1 , their charged and neutral excitations, and also the quasidegenerate ground states at arbitrary filling factors of the form ν =ν/*2pν*+1 , where n and p are integers and ν* is the CF filling factor. Comparison with exact results known for small systems for the ground and excited states at filling factors ν =1 /3 , 2/5, and 3/7 demonstrates our LLL-projected wave functions to be extremely accurate representations of the actual Coulomb eigenstates. Our construction enables the study of large systems of composite fermions on the torus, thereby opening the possibility of investigating numerous interesting questions and phenomena.

Key factors influencing the incidence of hemolysis: A critical appraisal of current evidence.

PubMed

McCaughey, Euan James; Vecellio, Elia; Lake, Rebecca; Li, Ling; Burnett, Leslie; Chesher, Douglas; Braye, Stephen; Mackay, Mark; Gay, Stephanie; Badrick, Tony; Westbrook, Johanna; Georgiou, Andrew

2017-01-01

Hemolysis is a leading cause of pre-analytical laboratory errors. The identification of contributing factors is an important step towards the development of effective practices to reduce and prevent hemolysis. We performed a review of PUBMED, Embase, Medline and CINAHL to identify articles published between January 2000 and August 2016 that identified factors influencing in vitro hemolysis rates. The 40 studies included in this review provide excellent evidence that hemolysis rates are higher in Emergency Departments (EDs), for non-antecubital draws, for specimens drawn using an intravenous catheter compared to venipuncture and for samples transported by pneumatic tube compared to by hand. There is also good evidence that hemolysis rates are higher when specimens are not collected by professional phlebotomists, larger volume specimen tubes are used, specimen tubes are filled less than halfway and tourniquet time is greater than one minute. The results of this review suggest that hospitals and clinical laboratories should consider deploying phlebotomists in EDs, drawing all blood through a venipuncture, using the antecubital region as the optimum blood collection site and transporting specimens by laboratory assistant/other personnel, or if this in not practical, ensuring that pneumatic transport systems are validated, maintained and monitored. Studies also recommend making hemolysis a hospital-wide issue and ensuring high-quality staff training and adherence to standard operating procedures to reduce hemolysis rates. Awareness of the factors that influence hemolysis rates, and adoption of strategies to mitigate these risk factors, is an important step towards creating quality practices to reduce hemolysis rates and improve the quality of patient care.

Respiratory disorders and the prevalence of sleep bruxism among schoolchildren aged 8 to 11 years.

PubMed

Drumond, Clarissa Lopes; Souza, Débora Souto; Serra-Negra, Júnia Maria; Marques, Leandro Silva; Ramos-Jorge, Maria Letícia; Ramos-Jorge, Joana

2017-03-01

The aim of this study was to evaluate the association between respiratory disorders and sleep bruxism, with an evaluation of demographic/socioeconomic factors and childhood stress as confounding variables. A cross-sectional study was performed in the city of Diamantina, Brazil, with 448 randomly selected schoolchildren aged 8 to 11 years. The schoolchildren underwent an oral examination for the evaluation of bruxism. Parents/caregivers answered a questionnaire for the assessment of sleep bruxism; socioeconomic-demographic factors; and respiratory disorders, such as rhinitis, sinusitis, and bronchitis. The schoolchildren filled out the Children's Stress Scale. Poisson regression models were constructed separately for each respiratory disorder to determine prevalence ratios (PRs) and 95% confidence intervals (CIs). Sleep bruxism was more prevalent among children with rhinitis (PR = 1.45; 95%CI 1.08-1.93; p = 0.012) and sinusitis (PR = 1.58; 95%CI 1.06-2.36; p = 0.023). No significant association was found between sleep bruxism and bronchitis. A greater frequency of sleep bruxism was found among children whose mothers had a higher level of schooling and those who reported stress in the resistance/exhaustion phase. Rhinitis and sinusitis were associated with sleep bruxism. Moreover, sleep bruxism was more prevalent among children whose mothers had a higher level of schooling and those with higher degrees of stress.

Diagnosis of high-temperature implosions using low- and high-opacity Krypton lines

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yaakobi, B.; Epstein, R.; Hooper, C.F. Jr.

1996-04-01

High-temperature laser target implosions can be achieved by using relatively thin-shell targets, and they can be. diagnosed by doping the fuel with krypton and measuring K-shell and L-shell lines. Electron temperatures of up to 5 keV at modest compressed densities ({approximately}1-5g/cm{sup 3}) are predicted for such experiments, with ion temperatures peaking above 10 keV at the center. It is found that the profiles of low-opacity (optically thin) lines in the expected density range are dominated by the Doppler broadening and can provide a measurement of the ion temperature if spectrometers of spectral resolution {Delta}{lambda}/{lambda} {ge} 1000 are used. For high-opacitymore » lines, obtained with a higher krypton fill pressure, the measurement of the escape factor can yield the {rho}R of the compressed fuel. At higher densities, Stark broadening of low-opacity lines becomes important and can provide a density measurement, whereas lines of higher opacity can be used to estimate the extent of mixing.« less

Study of the Peak Shear Strength of a Cement-Filled Hard Rock Joint

NASA Astrophysics Data System (ADS)

She, Cheng-Xue; Sun, Fu-Ting

2018-03-01

The peak shear strength of a cement-filled hard rock joint is studied by theoretical analysis and laboratory testing. Based on the concept of the shear resistance angle, by combining the statistical method and fractal theory, three new parameters are proposed to characterize the three-dimensional joint morphology, reflecting the effects of the average roughness, multi-scale asperities and the dispersion degree of the roughness distribution. These factors are independent of the measurement scale, and they reflect the anisotropy of the joint roughness. Compressive shear tests are conducted on cement-filled joints. Because joints without cement can be considered special cement-filled joints in which the filling degree of cement is zero, they are also tested. The cement-filled granite joint fails primarily along the granite-cement interfaces. The filling degree of cement controls the joint failure and affects its mechanical behaviour. With a decrease in the filling degree of cement, the joint cohesion decreases; however, the dilatancy angle and the basic friction angle of the interface increase. As the filling degree approaches zero, the cohesion approaches zero, while the dilatancy angle and the basic friction angle increase to those of the joint without cement. A set of formulas is proposed to evaluate the peak shear strength of the joints with and without cement. The formulas are shown to be reasonable by comparison with the tested peak shear strength, and they reflect the anisotropy of the strength. This research deepens the understanding of cement-filled joints and provides a method to evaluate their peak shear strength.

Asymmetrical color filling-in from the nasal to the temporal side of the blind spot

PubMed Central

Li, Hui; Luo, Junxiang; Lu, Yiliang; Kan, Janis; Spillmann, Lothar; Wang, Wei

2014-01-01

The physiological blind spot, corresponding to the optic disk in the retina, is a relatively large (6 × 8°) area in the visual field that receives no retinal input. However, we rarely notice the existence of it in daily life. This is because the blind spot fills in with the brightness, color, texture, and motion of the surround. The study of filling-in enables us to better understand the creative nature of the visual system, which generates perceptual information where there is none. Is there any retinotopic rule in the color filling-in of the blind spot? To find out, we used mono-colored and bi-colored annuli hugging the boundary of the blind spot. We found that mono-colored annuli filled in the blind spot uniformly. By contrast, bi-colored annuli, where one half had a given color, while the other half had a different one, filled in the blind spot asymmetrically. Specifically, the color surrounding the nasal half typically filled in about 75% of the blind spot area, whereas the color surrounding the temporal half filled in only about 25%. This asymmetry was dependent on the relative size of the half rings, but not the two colors used, and was absent when the bi-colored annulus was rotated by 90°. Here, the two colors on the upper and lower sides of the blind spot filled in the enclosed area equally. These results suggest that the strength of filling-in decreases with distance from the fovea consistent with the decrease of the cortical magnification factor. PMID:25100977

Asymmetrical color filling-in from the nasal to the temporal side of the blind spot.

PubMed

Li, Hui; Luo, Junxiang; Lu, Yiliang; Kan, Janis; Spillmann, Lothar; Wang, Wei

2014-01-01

The physiological blind spot, corresponding to the optic disk in the retina, is a relatively large (6 × 8°) area in the visual field that receives no retinal input. However, we rarely notice the existence of it in daily life. This is because the blind spot fills in with the brightness, color, texture, and motion of the surround. The study of filling-in enables us to better understand the creative nature of the visual system, which generates perceptual information where there is none. Is there any retinotopic rule in the color filling-in of the blind spot? To find out, we used mono-colored and bi-colored annuli hugging the boundary of the blind spot. We found that mono-colored annuli filled in the blind spot uniformly. By contrast, bi-colored annuli, where one half had a given color, while the other half had a different one, filled in the blind spot asymmetrically. Specifically, the color surrounding the nasal half typically filled in about 75% of the blind spot area, whereas the color surrounding the temporal half filled in only about 25%. This asymmetry was dependent on the relative size of the half rings, but not the two colors used, and was absent when the bi-colored annulus was rotated by 90°. Here, the two colors on the upper and lower sides of the blind spot filled in the enclosed area equally. These results suggest that the strength of filling-in decreases with distance from the fovea consistent with the decrease of the cortical magnification factor.

Occupational stress, anxiety and depression among Egyptian teachers.

PubMed

Desouky, Dalia; Allam, Heba

2017-09-01

Occupational stress (OS) among teachers predispose to depression and anxiety. No study was done to assess these problems among Egyptian teachers. This study aimed to assess the prevalence of OS, depression and anxiety among Egyptian teachers. A cross sectional study was done on 568 Egyptian teachers. The respondents filled a questionnaire on personal data, and the Arabic version of the Occupational Stress Index (OSI), the Arabic validated versions of Taylor manifest anxiety scale and the Beck Depression Inventory (BDI) were used to assess OS, anxiety and depression respectively. The prevalence of OS, anxiety and depression among teachers was (100%, 67.5% and 23.2%) respectively. OS, anxiety and depression scores were significantly higher among teachers with an age more than 40years, female teachers, primary school teachers, those with inadequate salary, higher teaching experience, higher qualifications and higher workload. A significant weak positive correlation was found between OS scores and anxiety and depression scores. This study indicated the need for future researches to address risk factors of OS and mental disorders among Egyptian teachers, and the need of periodical medical evaluation of teachers and medical and psychological support for the identified cases. Copyright © 2017. Published by Elsevier Ltd.

[Development, factor-analytical control and psychometric evaluation of a questionnaire on specialty choices among medical students].

PubMed

Hermann, K; Buchholz, A; Loh, A; Kiolbassa, K; Miksch, A; Joos, S; Götz, K

2012-07-01

A questionnaire was developed and validated which assesses factors influencing career choices of medical students and their perception of possibilities in general practice. The first questionnaire version, which was developed based on a systematic literature review, was checked for comprehensibility and redundancy using concurrent think aloud. The revised version was filled out by a pilot sample of medical students and the factor structure was assessed using principal component analysis (PCA). The final version was filled out in an online survey by medical students of all 5 Medical Faculties in the federal state of Baden-Wuerttemberg. The factor structure was validated with a confirmatory factor analysis (CFA). Reliability was assessed as internal consistency using Cronbach's α. The questionnaire comprises 2 parts: ratings of (A) the individual importance and of (B) the possibilities in general practice on 5-point scales. The first version comprising 118 items was shortened to 63 items after conducting interviews using concurrent think aloud. A further 3 items giving no information were removed after piloting the questionnaire on 179 students. The 27 items of part A were structured in 7 factors (PCA): image, personal ambition, patient orientation, work-life balance, future perspectives, job-related ambition, and variety in job. This structure had a critical fit in the CFA applied to the final version filled out by 1 299 students. Internal consistency of the factors was satisfactory to very good (Cronbach's α=0.55-0.81). The questionnaire showed good psychometric properties. Further, not assessed factors influence career choice resulting in unexplained variance in our dataset and the critical fit of the model. © Georg Thieme Verlag KG Stuttgart · New York.

Occupational factors and subsequent major depressive and generalized anxiety disorders in the prospective French national SIP study.

PubMed

Niedhammer, Isabelle; Malard, Lucile; Chastang, Jean-François

2015-02-28

The literature has been extensive on the associations between psychosocial work factors and mental health. Nevertheless, the studies using prospective design, various concepts and more than one measurement point in time for these factors and diagnostic interview to assess mental disorders remain seldom in the literature. This study is an attempt to fill the gap in this topic. The study was based on a national representative sample of 4717 workers of the French working population (SIP survey), interviewed in 2006 and reinterviewed again in 2010 and free of mental disorders at baseline. Psychosocial work factors, measured in both 2006 and 2010, included: psychological demands, decision latitude, social support, reward, emotional demands, role conflict, ethical conflict, tensions with the public, job insecurity and work-life imbalance. Other occupational factors related to working time/hours and physical work environment were also studied. Major depressive (MDD) and generalized anxiety disorders (GAD) were measured using a standardised diagnostic interview (MINI). Covariates were age, occupation, marital status, having a child under 3 y, social support outside work and stressful life events. Multivariate analyses were performed using weighted logistic regression models. Using models taking all occupational factors into account simultaneously, low reward and job insecurity predicted MDD. Psychological demands, low reward, emotional demands and job insecurity were predictive of GAD. The more frequent the exposure to job insecurity, the higher the risk of MDD and GAD, and the more frequent the exposure to psychological demands and low reward, the higher the risk of GAD. No effect was observed for repeated exposure to occupational factors. Classical and emergent psychosocial work factors were predictive factors of depression and anxiety with dose-response associations in terms of frequency of exposure. More attention may be needed on emergent psychosocial work factors and frequent exposure to these factors.

Longitudinal associations between dental caries increment and risk factors in late childhood and adolescence.

PubMed

Curtis, Alexandra M; VanBuren, John; Cavanaugh, Joseph E; Warren, John J; Marshall, Teresa A; Levy, Steven M

2018-05-12

To assess longitudinal associations between permanent tooth caries increment and both modifiable and non-modifiable risk factors, using best subsets model selection. The Iowa Fluoride Study has followed a birth cohort with standardized caries exams without radiographs of the permanent dentition conducted at about ages 9, 13, and 17 years. Questionnaires were sent semi-annually to assess fluoride exposures and intakes, select food and beverage intakes, and tooth brushing frequency. Exposure variables were averaged over ages 7-9, 11-13, and 15-17, reflecting exposure 2 years prior to the caries exam. Longitudinal models were used to relate period-specific averaged exposures and demographic variables to adjusted decayed and filled surface increments (ADJCI) (n = 392). The Akaike Information Criterion (AIC) was used to assess optimal explanatory variable combinations. From birth to age 9, 9-13, and 13-17 years, 24, 30, and 55 percent of subjects had positive permanent ADJCI, respectively. Ten models had AIC values within two units of the lowest AIC model and were deemed optimal based on AIC. Younger age, being male, higher mother's education, and higher brushing frequency were associated with lower caries increment in all 10 models, while milk intake was included in 3 of 10 models. Higher milk intakes were slightly associated with lower ADJCI. With the exception of brushing frequency, modifiable risk factors under study were not significantly associated with ADJCI. When possible, researchers should consider presenting multiple models if fit criteria cannot discern among a group of optimal models. © 2018 American Association of Public Health Dentistry.

21 CFR 113.100 - Processing and production records.

Code of Federal Regulations, 2014 CFR

2014-04-01

... products, maximum fill-in or drained weight, or other critical factors specified in the scheduled process... end of the holding period; nature of container. (6) Food preservation methods wherein critical factors... scheduled processes used, including the thermal process, its associated critical factors, as well as other...

21 CFR 113.100 - Processing and production records.

Code of Federal Regulations, 2012 CFR

2012-04-01

... products, maximum fill-in or drained weight, or other critical factors specified in the scheduled process... end of the holding period; nature of container. (6) Food preservation methods wherein critical factors... scheduled processes used, including the thermal process, its associated critical factors, as well as other...

21 CFR 113.100 - Processing and production records.

Code of Federal Regulations, 2013 CFR

2013-04-01

... products, maximum fill-in or drained weight, or other critical factors specified in the scheduled process... end of the holding period; nature of container. (6) Food preservation methods wherein critical factors... scheduled processes used, including the thermal process, its associated critical factors, as well as other...

[Leaf water potential of spring wheat and field pea under different tillage patterns and its relationships with environmental factors].

PubMed

Zhang, Ming; Zhang, Ren-Zhi; Cai, Li-Qun

2008-07-01

Based on a long-term experiment, the leaf water potential of spring wheat and field pea, its relationships with environmental factors, and the diurnal variations of leaf relative water content and water saturation deficient under different tillage patterns were studied. The results showed that during whole growth period, field pea had an obviously higher leaf water potential than spring wheat, but the two crops had similar diurnal variation trend of their leaf water potential, i.e., the highest in early morning, followed by a descent, and a gradual ascent after the descent. For spring wheat, the maximum leaf water potential appeared at its jointing and heading stages, followed by at booting and flowering stages, and the minimum appeared at filling stage. For field pea, the maximum leaf water potential achieved at squaring stage, followed by at branching and flowering stages, and the minimum was at podding stage. The leaf relative water content of spring wheat was the highest at heading stage, followed by at jointing and flowering stages, and achieved the minimum at filling stage; while the water saturation deficient was just in adverse. With the growth of field pea, its leaf relative water content decreased, but leaf water saturation deficient increased. The leaf water potential of both spring wheat and field pea had significant correlations with environmental factors, including soil water content, air temperature, solar radiation, relative air humidity, and air water potential. Path analysis showed that the meteorological factor which had the strongest effect on the diurnal variation of spring wheat' s and field pea' s leaf water potential was air water potential and air temperature, respectively. Compared with conventional tillage, the protective tillage patterns no-till, no-till plus straw mulching, and conventional tillage plus straw returning increased the leaf water potential and relative water content of test crops, and the effect of no-till plus straw mulching was most significant.

The Predisposing Factors between Dental Caries and Deviations from Normal Weight.

PubMed

Chopra, Amandeep; Rao, Nanak Chand; Gupta, Nidhi; Vashisth, Shelja; Lakhanpal, Manav

2015-04-01

Dental caries and deviations from normal weight are two conditions which share several broadly predisposing factors. So it's important to understand any relationship between dental state and body weight if either is to be managed appropriately. The study was done to find out the correlation between body mass index (BMI), diet, and dental caries among 12-15-year-old schoolgoing children in Panchkula District. A multistage sample of 12-15-year-old school children (n = 810) in Panchkula district, Haryana was considered. Child demographic details and diet history for 5 days was recorded. Data regarding dental caries status was collected using World Health Organization (1997) format. BMI was calculated and categorized according to the World Health Organization classification system for BMI. The data were subjected to statistical analysis using chi-square test and binomial regression developed using the Statistical Package for Social Sciences (SPSS) 20.0. The mean Decayed Missing Filled Teeth (DMFT) score was found to be 1.72 with decayed, missing, and filled teeth to be 1.22, 0.04, and 0.44, respectively. When the sample was assessed based on type of diet, it was found that vegetarians had higher mean DMFT (1.72) as compared to children having mixed diet. Overweight children had highest DMFT (3.21) which was followed by underweight (2.31) and obese children (2.23). Binomial regression revealed that females were 1.293 times at risk of developing caries as compared to males. Fair and poor Simplified-Oral Hygiene Index (OHI-S) showed 3.920 and 4.297 times risk of developing caries as compared to good oral hygiene, respectively. Upper high socioeconomic status (SES) is at most risk of developing caries. Underweight, overweight, and obese are at 2.7, 2.5, and 3 times risk of developing caries as compared to children with normal BMI, respectively. Dental caries and deviations from normal weight are two conditions which share several broadly predisposing factors such as diet, SES, lifestyle and other environmental factors.

[Treatment regulations and treatment limits: factors influencing clinical decision-making].

PubMed

Baberg, H T; Kielstein, R; de Zeeuw, J; Sass, H-M

2002-08-02

Providing or withholding of treatment is based on a variety of factors. We sought for criteria in clinical decision making and reviewed attitudes towards clinical intuition and the patient's will. 503 physicians (25.6 % females; mean age 36.3) in 49 departments at nine hospitals of the universities Bochum and Magdeburg filled in a validated questionnaire. The most important factors in the decision to carry out a therapy were "international standards" and "own experience". The decision to omit a therapy was mainly influenced by the "patient's wish". Physicians with a higher status judged their own experience higher than young physicians, who considered the experience of colleagues more important. "Severe accompanying illnesses" and "multimorbidity" were the most frequently named reasons to withdraw a therapy. Intuitive decision-making was rare, especially in young physicians, although these decisions were seldom risky and often successful. A patient's will plays a prominent role in clinical decision making, especially in decisions to withdraw or to withhold treatment. Cost containment and research interest have been called less important, a remarkable response from research-based university hospitals. Also remarkable is the recognition and importance of clinical intuition in situations of complex or missing information. This important aspect is rarely discussed in the literature or in medical education. The widely voiced concern that priorities in clinical care are guided by scientific interest, financial or technical possibilities could not be confirmed.

PHOTOMETRIC PROPERTIES FOR SELECTED ALGOL-TYPE BINARIES. II. AO SERPENTIS AND V338 HERCULIS

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yang, Y.-G.; Dai, H.-F.; Hu, S.-M.

2010-04-15

We present the first multiband photometry for the semidetached eclipsing binary AO Serpentis, observed on seven nights between 2009 April and July at the Weihai Observatory of Shandong University. By using the 2003 version of the Wilson-Devinney code, the photometric solutions of AO Ser and a similar object V338 Her were (re)deduced. The spectral types and orbital periods are A2 and P = 0.8793 days for AO Ser, F1V and P = 1.3057 days for V338 Her. The results reveal that two binaries are low mass ratio systems, whose secondary components fill their Roche lobes. The fill-out factors of themore » primary components are f = 58.6% for AO Ser and f = 54.2% for V338 Her, respectively. From the O - C curves of AO Ser and V338 Her, it is discovered that secular period changes with cyclic variations exist. The periods and semiamplitudes are 17.32({+-}0.01) yr and 0.0051({+-}0.0001) days for AO Ser, 29.07({+-}0.04) yr and 0.0116({+-}0.0015) days for V338 Her, respectively. This kind of cyclic oscillation may be attributed to either the light-time effect via an assumed third body or perhaps cyclic magnetic activity on the secondary component. For AO Ser, the long-term period decreases at a rate of dP/dt = -5.35({+-}0.03) x 10{sup -7} days yr{sup -1}, which may be caused by mass and angular momentum loss from the system. Considering the period decreasing, the fill-out factor of the primary for AO Ser will increase and it will finally fill its Roche lobe. Meanwhile, the secular period increase rate for V338 Her is dP/dt = +1.44({+-}0.24) x 10{sup -7} days yr{sup -1}, indicating that mass transfers from the less massive component to the more massive component. This will also cause the fill-out factor of the primary to increase. When the primaries fill their Roche lobes, AO Ser and V338 Her may evolve into contact stars, as predicted by the theory of thermal relaxation oscillations.« less

Mechanism for Angular Deformation of L-shaped Specimens —Influence of Filling Material and Shrinkage Factor—

NASA Astrophysics Data System (ADS)

Furuhashi, Hiroshi; Aoki, Takerou; Okabe, Sayaka; Arai, Tsuyoshi; Seto, Masahiro; Yamabe, Masashi

L-shape is the important and fundamental shape for injection molded parts. Therefore to reveal the corner angular deformation mechanism of this shape is also valuable for understanding the warpage mechanism of injection molded parts. In this study, we investigated the influence of the filling materials (fiber, talc and not filled) and two kinds of anisotropic shrinkage factors, solidification shrinkage and shrinkage caused by thermal expansion coefficient during cooling, to the angular deformation of L-shaped specimens and the following conclusions were obtained 1) The anisotropic solidification shrinkage of MD/TD and the anisotropic thermal expansion coefficient of MD/TD are considered to cause the angular deformation of L-shaped specimens. But the contribution ratios of these two anisotropies depend on the filling material for plastics. 2) The angular deformation of PP and PBT filled with glass fiber is mainly caused by the anisotropic thermal expansion coefficient and on the other hand, that of PP and PBT without filling material is caused by anisotropic solidification shrinkage. However both anisotropies cause the angular deformation of PP filled with talc. 3) The plate thickness dependence of the angular deformation of PP filled with talc is the singular peculiar phenomenon. The plate thickness dependence of anisotropic solidification shrinkage of this material (it is also singular) is considered to have an important influence on this phenomenon.

Likelihood-based gene annotations for gap filling and quality assessment in genome-scale metabolic models

DOE PAGES

Benedict, Matthew N.; Mundy, Michael B.; Henry, Christopher S.; ...

2014-10-16

Genome-scale metabolic models provide a powerful means to harness information from genomes to deepen biological insights. With exponentially increasing sequencing capacity, there is an enormous need for automated reconstruction techniques that can provide more accurate models in a short time frame. Current methods for automated metabolic network reconstruction rely on gene and reaction annotations to build draft metabolic networks and algorithms to fill gaps in these networks. However, automated reconstruction is hampered by database inconsistencies, incorrect annotations, and gap filling largely without considering genomic information. Here we develop an approach for applying genomic information to predict alternative functions for genesmore » and estimate their likelihoods from sequence homology. We show that computed likelihood values were significantly higher for annotations found in manually curated metabolic networks than those that were not. We then apply these alternative functional predictions to estimate reaction likelihoods, which are used in a new gap filling approach called likelihood-based gap filling to predict more genomically consistent solutions. To validate the likelihood-based gap filling approach, we applied it to models where essential pathways were removed, finding that likelihood-based gap filling identified more biologically relevant solutions than parsimony-based gap filling approaches. We also demonstrate that models gap filled using likelihood-based gap filling provide greater coverage and genomic consistency with metabolic gene functions compared to parsimony-based approaches. Interestingly, despite these findings, we found that likelihoods did not significantly affect consistency of gap filled models with Biolog and knockout lethality data. This indicates that the phenotype data alone cannot necessarily be used to discriminate between alternative solutions for gap filling and therefore, that the use of other information is necessary to obtain a more accurate network. All described workflows are implemented as part of the DOE Systems Biology Knowledgebase (KBase) and are publicly available via API or command-line web interface.« less

Likelihood-Based Gene Annotations for Gap Filling and Quality Assessment in Genome-Scale Metabolic Models

PubMed Central

Benedict, Matthew N.; Mundy, Michael B.; Henry, Christopher S.; Chia, Nicholas; Price, Nathan D.

2014-01-01

Genome-scale metabolic models provide a powerful means to harness information from genomes to deepen biological insights. With exponentially increasing sequencing capacity, there is an enormous need for automated reconstruction techniques that can provide more accurate models in a short time frame. Current methods for automated metabolic network reconstruction rely on gene and reaction annotations to build draft metabolic networks and algorithms to fill gaps in these networks. However, automated reconstruction is hampered by database inconsistencies, incorrect annotations, and gap filling largely without considering genomic information. Here we develop an approach for applying genomic information to predict alternative functions for genes and estimate their likelihoods from sequence homology. We show that computed likelihood values were significantly higher for annotations found in manually curated metabolic networks than those that were not. We then apply these alternative functional predictions to estimate reaction likelihoods, which are used in a new gap filling approach called likelihood-based gap filling to predict more genomically consistent solutions. To validate the likelihood-based gap filling approach, we applied it to models where essential pathways were removed, finding that likelihood-based gap filling identified more biologically relevant solutions than parsimony-based gap filling approaches. We also demonstrate that models gap filled using likelihood-based gap filling provide greater coverage and genomic consistency with metabolic gene functions compared to parsimony-based approaches. Interestingly, despite these findings, we found that likelihoods did not significantly affect consistency of gap filled models with Biolog and knockout lethality data. This indicates that the phenotype data alone cannot necessarily be used to discriminate between alternative solutions for gap filling and therefore, that the use of other information is necessary to obtain a more accurate network. All described workflows are implemented as part of the DOE Systems Biology Knowledgebase (KBase) and are publicly available via API or command-line web interface. PMID:25329157

Risk factors associated with treatment discontinuation and down-titration in type 2 diabetes patients treated with sulfonylureas.

PubMed

Iglay, Kristy; Qiu, Ying; Steve Fan, Chun-Po; Li, Zhiyi; Tang, Jackson; Laires, Pedro

2016-09-01

Sulfonylurea therapy among patients with type 2 diabetes mellitus (T2DM) can be disrupted due to adverse events, including hypoglycemia. A retrospective study using the MarketScan claims database quantified the frequency of sulfonylurea discontinuation or down-titration and identified associated risk factors. Adult patients with an index sulfonylurea prescription between 2008 and 2012 and 1 year continuous enrollment pre- and post-index were included. Therapy changes assessed over 1 year post-index included discontinuation and down-titration. Discontinuation occurred if the date of a fill was >90 days from the end date of the preceding fill. Down-titration occurred when a fill had a lower equivalent dose than the fill on the index date. Kaplan-Meier methods estimated the probability of either discontinuation or down-titration over 12 months, and Cox regression models identified associated risk factors. A total of 104,082 sulfonylurea users were included in the study and the probability of either discontinuation or down-titration at 3, 6 and 12 months was 23.2%, 38.9%, and 52.3%, respectively. Major risk factors associated with therapy changes included post-index hypoglycemia (discontinuation hazard ratio [HR] = 1.78 [1.68, 1.89]; down-titration HR =2.79 [2.40, 3.23]) and concomitant use of insulin (discontinuation HR =1.48 [1.40, 1.57]; down-titration HR =1.82 [1.56, 2.11]). Other risk factors included younger age, female gender, use of second generation sulfonylureas, prior cardiovascular comorbidity and liver disease. The study was not able to assess unreported, potentially mild cases of hypoglycemia, nor was it able to evaluate the association between changes in therapy and HbA1c levels or body weight. More than half of T2DM patients who initiated sulfonylurea therapy discontinued or down-titrated within 1 year. Insulin use and hypoglycemia were associated with sulfonylurea therapy change.

Mid-infrared interferometry of Seyfert galaxies: Challenging the Standard Model

NASA Astrophysics Data System (ADS)

López-Gonzaga, N.; Jaffe, W.

2016-06-01

Aims: We aim to find torus models that explain the observed high-resolution mid-infrared (MIR) measurements of active galactic nuclei (AGN). Our goal is to determine the general properties of the circumnuclear dusty environments. Methods: We used the MIR interferometric data of a sample of AGNs provided by the instrument MIDI/VLTI and followed a statistical approach to compare the observed distribution of the interferometric measurements with the distributions computed from clumpy torus models. We mainly tested whether the diversity of Seyfert galaxies can be described using the Standard Model idea, where differences are solely due to a line-of-sight (LOS) effect. In addition to the LOS effects, we performed different realizations of the same model to include possible variations that are caused by the stochastic nature of the dusty models. Results: We find that our entire sample of AGNs, which contains both Seyfert types, cannot be explained merely by an inclination effect and by including random variations of the clouds. Instead, we find that each subset of Seyfert type can be explained by different models, where the filling factor at the inner radius seems to be the largest difference. For the type 1 objects we find that about two thirds of our objects could also be described using a dusty torus similar to the type 2 objects. For the remaining third, it was not possible to find a good description using models with high filling factors, while we found good fits with models with low filling factors. Conclusions: Within our model assumptions, we did not find one single set of model parameters that could simultaneously explain the MIR data of all 21 AGN with LOS effects and random variations alone. We conclude that at least two distinct cloud configurations are required to model the differences in Seyfert galaxies, with volume-filling factors differing by a factor of about 5-10. A continuous transition between the two types cannot be excluded.

Investigation of the Mechanism of Roof Caving in the Jinchuan Nickel Mine, China

NASA Astrophysics Data System (ADS)

Ding, Kuo; Ma, Fengshan; Guo, Jie; Zhao, Haijun; Lu, Rong; Liu, Feng

2018-04-01

On 13 March 2016, a sudden, violent roof caving event with a collapse area of nearly 11,000 m2 occurred in the Jinchuan Nickel Mine and accompanied by air blasts, loud noises and ground vibrations. This collapse event coincided with related, conspicuous surface subsidence across an area of nearly 19,000 m2. This article aims to analyse this collapse event. In previous studies, various mining-induced collapses have been studied, but collapse accidents associated with the filling mining method are very rare and have not been thoroughly studied. The filling method has been regarded as a safe mining method for a long time, so research on associated collapse mechanisms is of considerable significance. In this study, a detailed field investigation of roadway damage was performed, and GPS monitoring results were used to analyse the surface failure. In addition, a numerical model was constructed based on the geometry of the ore body and a major fault. The analysis of the model revealed three failure mechanisms acting during different stages of destruction: double-sided embedded beam deformation, fault activation, and cantilever-articulated rock beam failure. The fault activation and the specific filling method are the key factors of this collapse event. To gain a better understanding of these factors, the shear stress and normal stress along the fault plane were monitored to determine the variation in stress at different failure stages. Discrete element models were established to study two filling methods and to analyse the stability of different filling structures.

Feasibility of biochar application on a landfill final cover-a review on balancing ecology and shallow slope stability.

PubMed

Chen, Xun-Wen; Wong, James Tsz-Fung; Ng, Charles Wang-Wai; Wong, Ming-Hung

2016-04-01

Due to the increasing concerns on global warming, scarce land for agriculture, and contamination impacts on human health, biochar application is being considered as one of the possible measures for carbon sequestration, promoting higher crop yield and contamination remediation. Significant amount of researches focusing on these three aspects have been conducted during recent years. Biochar as a soil amendment is effective in promoting plant performance and sustainability, by enhancing nutrient bioavailability, contaminants immobilization, and microbial activities. The features of biochar in changing soil physical and biochemical properties are essential in affecting the sustainability of an ecosystem. Most studies showed positive results and considered biochar application as an effective and promising measure for above-mentioned interests. Bio-engineered man-made filled slope and landfill slope increasingly draw the attention of geologists and geotechnical engineers. With increasing number of filled slopes, sustainability, low maintenance, and stability are the major concerns. Biochar as a soil amendment changes the key factors and parameters in ecology (plant development, soil microbial community, nutrient/contaminant cycling, etc.) and slope engineering (soil weight, internal friction angle and cohesion, etc.). This paper reviews the studies on the production, physical and biochemical properties of biochar and suggests the potential areas requiring study in balancing ecology and man-made filled slope and landfill cover engineering. Biochar-amended soil should be considered as a new type of soil in terms of soil mechanics. Biochar performance depends on soil and biochar type which imposes challenges to generalize the research outcomes. Aging process and ecotoxicity studies of biochar are strongly required.

Elution of monomer from different bulk fill dental composite resins.

PubMed

Cebe, Mehmet Ata; Cebe, Fatma; Cengiz, Mehmet Fatih; Cetin, Ali Rıza; Arpag, Osman Fatih; Ozturk, Bora

2015-07-01

The purpose of this study was to evaluate the elution of Bis-GMA, TEGDMA, HEMA, and Bis-EMA monomers from six bulk fill composite resins over four different time periods, using HPLC. Six different composite resin materials were used in the present study: Tetric Evo Ceram Bulk Fill (Ivoclar Vivadent, Amherst, NY), X-tra Fill (VOCO, Cuxhaven, Germany), Sonic Fill (Kerr, Orange, CA, USA), Filtek Bulk Fill (3M ESPE Dental Product, St. Paul, MN), SDR (Dentsply, Konstanz, Germany), EQUIA (GC America INC, Alsip, IL). The samples (4mm thickness, 5mm diameter) were prepared and polymerized for 20s with a light emitted diode unit. After fabrication, each sample was immediately immersed in 75wt% ethanol/water solution used as extraction fluid and stored in the amber colored bottles at room temperature. Ethanol/water samples were taken (0.5mL) at predefined time intervals:10m (T1), 1h (T2), 24h (T3) and 30 days (T4). These samples were analyzed by HPLC. The obtained data were analyzed with one-way ANOVA and Tukey HSD at significance level of p<0.05. Amount of eluted Bis-EMA and Bis-GMA from Tetric Evo Ceram Bulk Fill and amount of eluted TEGDMA and HEMA from X-tra Fill higher than others composites (p<0.05). Residual monomers were eluted from bulk fill composite resins in all time periods and the amount of eluted monomers was increased with time. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Effectiveness of Non-Lethal Capabilities in a Maritime Environment

DTIC Science & Technology

2006-09-01

demonstrates both the space filling properties for quantitative factors of the NOLH and the lack of correlation between the factors. 27 Figure 12 ...11 b. Optical Dazzler ........................................................................ 12 c...Warning Munitions................................................................. 12 2. Lethal Capabilities

Characteristic investigation of Golay9 multiple mirror telescope with a spherical primary mirror

NASA Astrophysics Data System (ADS)

Wu, Feng; Wu, Quanying; Zhu, Xifang; Xiang, Ruxi; Qian, Lin

2017-10-01

The sparse aperture provides a novel solution to the manufacturing difficulties of modern super large telescopes. Golay configurations are optimal in the sparse aperture family. Characteristics of the Golay9 multiple mirror telescope having a spherical primary mirror are investigated. The arrangement of the nine sub-mirrors is discussed after the planar Golay9 configuration is analyzed. The characteristics of the entrance pupil are derived by analyzing the sub-aperture shapes with different relative apertures and sub-mirror sizes. Formulas about the fill factor and the overlay factor are deduced. Their maximal values are presented based on the derived tangency condition. Formulas for the point spread function (PSF) and the modulation transfer function (MTF) of the Golay9 MMT are also deduced. Two Golay9 MMT have been developed by Zemax simulation. Their PSF, MTF, fill factors, and overlay factors prove that our theoretical results are consistent with the practical simulation ones.

Open circuit voltage-decay behavior in amorphous p-i-n solar due to injection

NASA Astrophysics Data System (ADS)

Smrity, Manu; Dhariwal, S. R.

2018-05-01

The paper deals with the basic recombination processes at the dangling bond and the band tail states at various levels of injection, expressed in terms of short-circuit current density and their role in the behavior of amorphous solar cells. As the level of injection increases the fill factor decreases whereas the open circuit voltage increases very slowly, showing a saturation tendency. Calculations have been done for two values of tail state densities and shows that with an increase in tail state densities both, the fill factor and open circuit voltage decreases, results an overall degradation of the solar cell.

Efficient photovoltaic heterojunctions of indium tin oxides on silicon

NASA Technical Reports Server (NTRS)

Dubow, J. B.; Sites, J. R.; Burk, D. E.

1976-01-01

Heterojunction diodes of indium tin oxide films sputtered on to p-silicon using ion-beam techniques display significant photovoltaic effects when exposed to sunlight. Galvanomagnetic and optical measurements confirm that the oxide films are highly degenerate transparent semiconductors. At a tin oxide concentration of 10%, an open-circuit voltage of 0.51 V was observed along with a short-circuit current of 32 mA/sq cm, a fill factor of 0.70, and a conversion efficiency of 12%. As the concentration was raised to 70%, the voltage remained steady, the current fell to 27 mA/sq cm, and the fill factor fell to 0.60

Tailoring the dispersion behavior of silicon nanophotonic slot waveguides.

PubMed

Mas, Sara; Caraquitena, José; Galán, José V; Sanchis, Pablo; Martí, Javier

2010-09-27

We investigate the chromatic dispersion properties of silicon channel slot waveguides in a broad spectral region centered at ~1.5 μm. The variation of the dispersion profile as a function of the slot fill factor, i.e., the ratio between the slot and waveguide widths, is analyzed. Symmetric as well as asymmetric geometries are considered. In general, two different dispersion regimes are identified. Furthermore, our analysis shows that the zero and/or the peak dispersion wavelengths can be tailored by a careful control of the geometrical waveguide parameters including the cross-sectional area, the slot fill factor, and the slot asymmetry degree.

Tuning the dielectric properties of metallic-nanoparticle/elastomer composites by strain.

PubMed

Gaiser, Patrick; Binz, Jonas; Gompf, Bruno; Berrier, Audrey; Dressel, Martin

2015-03-14

Tunable metal/dielectric composites are promising candidates for a large number of potential applications in electronics, sensor technologies and optical devices. Here we systematically investigate the dielectric properties of Ag-nanoparticles embedded in the highly flexible elastomer poly-dimethylsiloxane (PDMS). As tuning parameter we use uniaxial and biaxial strain applied to the composite. We demonstrate that both static variations of the filling factor and applied strain lead to the same behavior, i.e., the filling factor of the composite can be tuned by application of strain. In this way the effective static permittivity εeff of the composite can be varied over a very large range. Once the Poisson's ratio of the composite is known, the strain dependent dielectric constant can be accurately described by effective medium theory without any additional free fit parameter up to metal filling factors close to the percolation threshold. It is demonstrated that, starting above the percolation threshold in the metallic phase, applying strain provides the possibility to cross the percolation threshold into the insulating region. The change of regime from conductive phase down to insulating follows the description given by percolation theory and can be actively controlled.

Comparison of air-charged and water-filled urodynamic pressure measurement catheters.

PubMed

Cooper, M A; Fletter, P C; Zaszczurynski, P J; Damaser, M S

2011-03-01

Catheter systems are utilized to measure pressure for diagnosis of voiding dysfunction. In a clinical setting, patient movement and urodynamic pumps introduce hydrostatic and motion artifacts into measurements. Therefore, complete characterization of a catheter system includes its response to artifacts as well its frequency response. The objective of this study was to compare the response of two disposable clinical catheter systems: water-filled and air-charged, to controlled pressure signals to assess their similarities and differences in pressure transduction. We characterized frequency response using a transient step test, which exposed the catheters to a sudden change in pressure; and a sinusoidal frequency sweep test, which exposed the catheters to a sinusoidal pressure wave from 1 to 30 Hz. The response of the catheters to motion artifacts was tested using a vortex and the response to hydrostatic pressure changes was tested by moving the catheter tips to calibrated heights. Water-filled catheters acted as an underdamped system, resonating at 10.13 ± 1.03 Hz and attenuating signals at frequencies higher than 19 Hz. They demonstrated significant motion and hydrostatic artifacts. Air-charged catheters acted as an overdamped system and attenuated signals at frequencies higher than 3.02 ± 0.13 Hz. They demonstrated significantly less motion and hydrostatic artifacts than water-filled catheters. The transient step and frequency sweep tests gave comparable results. Air-charged and water-filled catheters respond to pressure changes in dramatically different ways. Knowledge of the characteristics of the pressure-measuring system is essential to finding the best match for a specific application. Copyright © 2011 Wiley-Liss, Inc.

Progress towards a more predictive model for hohlraum radiation drive and symmetry

NASA Astrophysics Data System (ADS)

Jones, O. S.; Suter, L. J.; Scott, H. A.; Barrios, M. A.; Farmer, W. A.; Hansen, S. B.; Liedahl, D. A.; Mauche, C. W.; Moore, A. S.; Rosen, M. D.; Salmonson, J. D.; Strozzi, D. J.; Thomas, C. A.; Turnbull, D. P.

2017-05-01

For several years, we have been calculating the radiation drive in laser-heated gold hohlraums using flux-limited heat transport with a limiter of 0.15, tabulated values of local thermodynamic equilibrium gold opacity, and an approximate model for not in a local thermodynamic equilibrium (NLTE) gold emissivity (DCA_2010). This model has been successful in predicting the radiation drive in vacuum hohlraums, but for gas-filled hohlraums used to drive capsule implosions, the model consistently predicts too much drive and capsule bang times earlier than measured. In this work, we introduce a new model that brings the calculated bang time into better agreement with the measured bang time. The new model employs (1) a numerical grid that is fully converged in space, energy, and time, (2) a modified approximate NLTE model that includes more physics and is in better agreement with more detailed offline emissivity models, and (3) a reduced flux limiter value of 0.03. We applied this model to gas-filled hohlraum experiments using high density carbon and plastic ablator capsules that had hohlraum He fill gas densities ranging from 0.06 to 1.6 mg/cc and hohlraum diameters of 5.75 or 6.72 mm. The new model predicts bang times to within ±100 ps for most experiments with low to intermediate fill densities (up to 0.85 mg/cc). This model predicts higher temperatures in the plasma than the old model and also predicts that at higher gas fill densities, a significant amount of inner beam laser energy escapes the hohlraum through the opposite laser entrance hole.

Thickness dependences of solar cell performance

NASA Technical Reports Server (NTRS)

Sah, C. T.

1982-01-01

The significance of including factors such as the base resistivity loss for solar cells thicker than 100 microns and emitter and BSF layer recombination for thin cells in predicting the fill factor and efficiency of solar cells is demonstrated analytically. A model for a solar cell is devised with the inclusion of the dopant impurity concentration profile, variation of the electron and hole mobility with dopant concentration, the concentration and thermal capture and emission rates of the recombination center, device temperature, the AM1 spectra and the Si absorption coefficient. Device equations were solved by means of the transmission line technique. The analytical results were compared with those of low-level theory for cell performance. Significant differences in predictions of the fill factor resulted, and inaccuracies in the low-level approximations are discussed.

Detection of sulphur in the galactic center

NASA Technical Reports Server (NTRS)

Herter, T.; Briotta, D. A., Jr.; Gull, G. E.; Shure, M. A.; Houck, J. R.

1983-01-01

A strong detection at the (SIII) 18.71 micron line is reported for the Galactic Center region, Sgr A West. A line flux of 1.7 + or - 0.2x10 to the -17th power W cm(-2) is found for a 20-arc second beam-size measurement centered on IRS 1. A preliminary analysis indicates that the SIII abundance relative to hydrogen is consistent with the cosmic abundance of sulfur, 1.6x10 to the -5th power, if a filling factor of unity within the known clumps is assumed. However, the sulfur abundance in the Galactic Center may be as much as a factor of 3 overabundant if a filling factor of 0.03 is adopted, a value found to hold for some galactic HII regions.

Via fill properties of organic BARCs in dual-damascene application

NASA Astrophysics Data System (ADS)

Huang, Runhui

2004-05-01

With the introduction of copper as the interconnect metal, the Dual Damascene (DD) process has been integrated into integrated circuit (IC) device fabrication. The DD process utilizes organic bottom anti-reflective coatings (BARCs) not only to eliminate the thin film interference effects but also to act as via fill materials. However, three serious processing problems are encountered with organic BARCs. One is the formation of voids, which are trapped gas bubbles (evaporating solvent, byproduct of the curing reaction and air) inside the vias. Another problem is non-uniform BARC layer thickness in different via pitch areas. The third problem is the formation of fences during plasma etch. Fences are formed from materials that are removed by plasma and subsequently deposited on the sidewall surrounding the via openings during the etching process. Voids can cause variations in BARC top thickness, optical properties, via fill percentage, and plasma etch rate. This study focuses on the factors that influence the formation of voids and addresses the ways to eliminate them by optimizing the compositions of formulations and the processing conditions. Effects of molecular weight of the polymer, nature of the crosslinker, additives, and bake temperature were examined. The molecular weight of the polymer is one of the important factors that needs to be controlled carefully. Polymers with high molecular weights tend to trap voids inside the vias. Low molecular weight polymers have low Tg and low viscosity, which enables good thermal flow so that the BARC can fill vias easily without voids. Several kinds of crosslinkers were investigated in this study. When used with the same polymer system, formulations with different crosslinkers show varying results that affect planar fill, sidewall coverage, and, in some cases, voids. Additives also can change via fill behavior dramatically, and choosing the right additive will improve the via fill property. Processing conditions such as bake temperature also greatly affect via fill. Depending on the polymer thermal property and crosslinking reaction, varying the bake temperature can change the via fill behavior of the BARC. By understanding the nature of the polymer, the crosslinking reaction, and the processing conditions, we are able to design BARCs with better flow property to provide planar topography without voids inside the vias.

Experimental Investigations on Axially and Eccentrically Loaded Masonry Walls

NASA Astrophysics Data System (ADS)

Keshava, Mangala; Raghunath, Seshagiri Rao

2017-12-01

In India, un-reinforced masonry walls are often used as main structural components in load bearing structures. Indian code on masonry accounts the reduction in strength of walls by using stress reduction factors in its design philosophy. This code was introduced in 1987 and reaffirmed in 1995. The present study investigates the use of these factors for south Indian masonry. Also, with the gaining popularity in block work construction, the aim of this study was to find out the suitability of these factors given in the Indian code to block work masonry. Normally, the load carrying capacity of masonry walls can be assessed in three ways, namely, (1) tests on masonry constituents, (2) tests on masonry prisms and (3) tests on full-scale wall specimens. Tests on bricks/blocks, cement-sand mortar, brick/block masonry prisms and 14 full-scale brick/block masonry walls formed the experimental investigation. The behavior of the walls was investigated under varying slenderness and eccentricity ratios. Hollow concrete blocks normally used as in-fill masonry can be considered as load bearing elements as its load carrying capacity was found to be high when compared to conventional brick masonry. Higher slenderness and eccentricity ratios drastically reduced the strength capacity of south Indian brick masonry walls. The reduction in strength due to slenderness and eccentricity is presented in the form of stress reduction factors in the Indian code. These factors obtained through experiments on eccentrically loaded brick masonry walls was lower while that of brick/block masonry under axial loads was higher than the values indicated in the Indian code. Also the reduction in strength is different for brick and block work masonry thus indicating the need for separate stress reduction factors for these two masonry materials.

Energy-dependent dynamics of keV to MeV electrons in the inner zone, outer zone, and slot regions.

PubMed

Reeves, Geoffrey D; Friedel, Reiner H W; Larsen, Brian A; Skoug, Ruth M; Funsten, Herbert O; Claudepierre, Seth G; Fennell, Joseph F; Turner, Drew L; Denton, Mick H; Spence, Harlan E; Blake, J Bernard; Baker, Daniel N

2016-01-01

We present observations of the radiation belts from the Helium Oxygen Proton Electron and Magnetic Electron Ion Spectrometer particle detectors on the Van Allen Probes satellites that illustrate the energy dependence and L shell dependence of radiation belt enhancements and decays. We survey events in 2013 and analyze an event on 1 March in more detail. The observations show the following: (a) at all L shells, lower energy electrons are enhanced more often than higher energies; (b) events that fill the slot region are more common at lower energies; (c) enhancements of electrons in the inner zone are more common at lower energies; and (d) even when events do not fully fill the slot region, enhancements at lower energies tend to extend to lower L shells than higher energies. During enhancement events the outer zone extends to lower L shells at lower energies while being confined to higher L shells at higher energies. The inner zone shows the opposite with an outer boundary at higher L shells for lower energies. Both boundaries are nearly straight in log(energy) versus L shell space. At energies below a few 100 keV, radiation belt electron penetration through the slot region into the inner zone is commonplace, but the number and frequency of "slot filling" events decreases with increasing energy. The inner zone is enhanced only at energies that penetrate through the slot. Energy- and L shell-dependent losses (that are consistent with whistler hiss interactions) return the belts to more quiescent conditions.

Mobile spin impurity in an optical lattice

NASA Astrophysics Data System (ADS)

Duncan, C. W.; Bellotti, F. F.; Öhberg, P.; Zinner, N. T.; Valiente, M.

2017-07-01

We investigate the Fermi polaron problem in a spin-1/2 Fermi gas in an optical lattice for the limit of both strong repulsive contact interactions and one dimension. In this limit, a polaronic-like behaviour is not expected, and the physics is that of a magnon or impurity. While the charge degrees of freedom of the system are frozen, the resulting tight-binding Hamiltonian for the impurity’s spin exhibits an intriguing structure that strongly depends on the filling factor of the lattice potential. This filling dependency also transfers to the nature of the interactions for the case of two magnons and the important spin balanced case. At low filling, and up until near unit filling, the single impurity Hamiltonian faithfully reproduces a single-band, quasi-homogeneous tight-binding problem. As the filling is increased and the second band of the single particle spectrum of the periodic potential is progressively filled, the impurity Hamiltonian, at low energies, describes a single particle trapped in a multi-well potential. Interestingly, once the first two bands are fully filled, the impurity Hamiltonian is a near-perfect realisation of the Su-Schrieffer-Heeger model. Our studies, which go well beyond the single-band approximation, that is, the Hubbard model, pave the way for the realisation of interacting one-dimensional models of condensed matter physics.

Micro-channel filling flow considering surface tension effect

NASA Astrophysics Data System (ADS)

Kim, Dong Sung; Lee, Kwang-Cheol; Kwon, Tai Hun; Lee, Seung S.

2002-05-01

Understanding filling flow into micro-channels is important in designing micro-injection molding, micro-fluidic devices and an MIMIC (micromolding in capillaries) process. In this paper, we investigated, both experimentally and numerically, 'transient filling' flow into micro-channels, which differs from steady-state completely 'filled' flow in micro-channels. An experimental flow visualization system was devised to facilitate observation of flow characteristics in filling into micro-channels. Three sets of micro-channels of various widths of different thicknesses (20, 30, and 40 μm) were fabricated using SU-8 on the silicon substrate to find a geometric effect with regard to pressure gradient, viscous force and, in particular, surface tension. A numerical analysis system has also been developed taking into account the surface tension effect with a contact angle concept. Experimental observations indicate that surface tension significantly affects the filling flow to such an extent that even a flow blockage phenomenon was observed at channels of small width and thickness. A numerical analysis system also confirms that the flow blockage phenomenon could take place due to the flow hindrance effect of surface tension, which is consistent with experimental observation. For proper numerical simulations, two correction factors have also been proposed to correct the conventional hydraulic radius for the filling flow in rectangular cross-sectioned channels.

Molecular and morphological surface analysis: effect of filling pastes and cleaning agents on root dentin.

PubMed

Dainezi, Vanessa Benetello; Iwamoto, Alexsandra Shizue; Martin, Airton Abrahão; Soares, Luís Eduardo Silva; Hosoya, Yumiko; Pascon, Fernanda Miori; Puppin-Rontani, Regina Maria

2017-01-01

This study evaluated the effect of different filling pastes and cleaning agents on the root dentin of primary teeth using Fourier-transformed Raman spectroscopy (FT-Raman), micro energy-dispersive X-ray fluorescence (µ-EDXRF) and scanning electron microscopic (SEM) analysis. Eighty roots of primary teeth were endodontically prepared and distributed into 4 groups and filled according to the following filling pastes: Control-no filling (CP), Calen®+zinc oxide (CZ), Calcipex II® (CII), Vitapex® (V). After seven days, filling paste groups were distributed to 4 subgroups according to cleaning agents (n=5): Control-no cleaning (C), Ethanol (E), Tergenform® (T), 35% Phosphoric acid (PA). Then, the roots were sectioned and the dentin root sections were internally evaluated by FT-Raman, µ-EDXRF and SEM. Data was submitted to two-way ANOVA and Tukey tests (α=0.05). Regarding filling pastes, there was no significant difference in organic content. CP provided the lowest calcium values and, calcium/phosphoric ratio (Ca/P), and the highest phosphoric values. For cleaning agents there was no difference in organic content when compared to the C; however, T showed significantly higher calcium and Ca/P than PA. All groups showed similar results for phosphorus. The dentin smear layer was present after use of the cleaning agents, except PA. The filling pastes changed the inorganic content, however they did not change the organic content. Cleaning agents did not alter the inorganic and organic content. PA cleaned and opened dentin tubules.

The Determinants of State Spending on Higher Education: How Capital Project Funding Differs from General Fund Appropriations

ERIC Educational Resources Information Center

Ness, Erik C.; Tandberg, David A.

2013-01-01

Our fixed-effects panel data analysis of state spending on higher education fills a near void of studies examining capital expenditures on higher education. In our study, we found that political characteristics (e.g., interest group activity, organizational structure, and formal powers) largely account for differences between general fund and…

Enhanced thermoelectric response in the fractional quantum Hall effect

NASA Astrophysics Data System (ADS)

Roura-Bas, Pablo; Arrachea, Liliana; Fradkin, Eduardo

2018-02-01

We study the linear thermoelectric response of a quantum dot embedded in a constriction of a quantum Hall bar with fractional filling factors ν =1 /m within Laughlin series. We calculate the figure of merit Z T for the maximum efficiency at a fixed temperature difference. We find a significant enhancement of this quantity in the fractional filling in relation to the integer-filling case, which is a direct consequence of the fractionalization of the electron in the fractional quantum Hall state. We present simple theoretical expressions for the Onsager coefficients at low temperatures, which explicitly show that Z T and the Seebeck coefficient increase with m .

Grip force and force sharing in two different manipulation tasks with bottles.

PubMed

Cepriá-Bernal, Javier; Pérez-González, Antonio; Mora, Marta C; Sancho-Bru, Joaquín L

2017-07-01

Grip force and force sharing during two activities of daily living were analysed experimentally in 10 right-handed subjects. Four different bottles, filled to two different levels, were manipulated for two tasks: transporting and pouring. Each test subject's hand was instrumented with eight thin wearable force sensors. The grip force and force sharing were significantly different for each bottle model. Increasing the filling level resulted in an increase in grip force, but the ratio of grip force to load force was higher for lighter loads. The task influenced the force sharing but not the mean grip force. The contributions of the thumb and ring finger were higher in the pouring task, whereas the contributions of the palm and the index finger were higher in the transport task. Mean force sharing among fingers was 30% for index, 29% for middle, 22% for ring and 19% for little finger. Practitioner Summary: We analysed grip force and force sharing in two manipulation tasks with bottles: transporting and pouring. The objective was to understand the effects of the bottle features, filling level and task on the contribution of different areas of the hand to the grip force. Force sharing was different for each task and the bottles features affected to both grip force and force sharing.

Effect of salt intensity in soup on ad libitum intake and on subsequent food choice.

PubMed

Bolhuis, Dieuwerke P; Lakemond, Catriona M M; de Wijk, Rene A; Luning, Pieternel A; de Graaf, Cees

2012-02-01

The effect of salt intensity on ad libitum intake of tomato soup was investigated when soup was served as a first course and as a second course. Also the effect of salt intensity in soup on subsequent sweet vs. savory choice of sandwich fillings was investigated. Forty-three healthy subjects consumed ad libitum a low-salt (LS), ideal-salt (IS) and high-salt (HS) tomato soup in both meal settings. The salt concentrations were selected on an individual basis, in a way that IS was most pleasant and LS and HS were similar in pleasantness. The ad libitum intake of IS soup was higher than that of LS and HS soup, and the ad libitum intake of LS soup was higher than that of HS soup. The meal setting, soup as a first or as a second course, did not affect ad libitum intake. Salt intensity in soup did not predict sweet vs. savory choice of fillings in grams or energy, although most sodium from fillings was consumed after intake of HS soup. In conclusion, a higher salt intensity lead to lower ad libitum intake of soup similar in palatability (LS vs. HS). In addition, salt intensity in soup does not predict sweet vs. savory food choice. Copyright © 2011 Elsevier Ltd. All rights reserved.

A novel wood flour-filled composite based on microfibrillar high-density polyethylene (HDPE)/Nylon-6 blends.

PubMed

Liu, Hongzhi; Yao, Fei; Xu, Yanjun; Wu, Qinglin

2010-05-01

A novel wood flour (WF)-filled composite based on the microfibrillar high-density polyethylene (HDPE) and Nylon-6 co-blend, in which both in situ formed Nylon-6 microfibrils and WF acted as reinforcing elements, was successfully developed using a two-step extrusion method. At the 30wt.% WF loading level, WF-filled composite based on the microfibrillized HDPE/Nylon-6 blend exhibited higher strengths and moduli than the corresponding HDPE-based composite. The incorporation of WF reduced short-term creep response of HDPE matrix and the presence of Nylon-6 microfibrils further contributed to the creep reduction. Copyright 2009 Elsevier Ltd. All rights reserved.

Mechanical and microwave absorbing properties of carbon-filled polyurethane.

PubMed

Kucerová, Z; Zajícková, L; Bursíková, V; Kudrle, V; Eliás, M; Jasek, O; Synek, P; Matejková, J; Bursík, J

2009-01-01

Polyurethane (PU) matrix composites were prepared with various carbon fillers at different filler contents in order to investigate their structure, mechanical and microwave absorbing properties. As fillers, flat carbon microparticles, carbon microfibers and multiwalled carbon nanotubes (MWNT) were used. The microstructure of the composite was examined by scanning electron microscopy and transmission electron microscopy. Mechanical properties, namely universal hardness, plastic hardness, elastic modulus and creep were assessed by means of depth sensing indentation test. Mechanical properties of PU composite filled with different fillers were investigated and the composite always exhibited higher hardness, elastic modulus and creep resistance than un-filled PU. Influence of filler shape, content and dispersion was also investigated.

Comparison of CIGS solar cells made with different structures and fabrication techniques

DOE PAGES

Mansfield, Lorelle M.; Garris, Rebekah L.; Counts, Kahl D.; ...

2016-11-03

Cu(In, Ga)Se2 (CIGS)-based solar cells from six fabricators were characterized and compared. The devices had differing substrates, absorber deposition processes, buffer materials, and contact materials. The effective bandgaps of devices varied from 1.05 to 1.22 eV, with the lowest optical bandgaps occurring in those with metal-precursor absorber processes. Devices with Zn(O, S) or thin CdS buffers had quantum efficiencies above 90% down to 400 nm. Most voltages were 250-300 mV below the Shockley-Queisser limit for their bandgap. Electroluminescence intensity tracked well with the respective voltage deficits. Fill factor (FF) was as high as 95% of the maximum for each device'smore » respective current and voltage, with higher FF corresponding to lower diode quality factors (~1.3). An in-depth analysis of FF losses determined that diode quality reflected in the quality factor, voltage-dependent photocurrent, and, to a lesser extent, the parasitic resistances are the limiting factors. As a result, different absorber processes and device structures led to a range of electrical and physical characteristics, yet this investigation showed that multiple fabrication pathways could lead to high-quality and high-efficiency solar cells.« less

Comparison of CIGS solar cells made with different structures and fabrication techniques

DOE Office of Scientific and Technical Information (OSTI.GOV)

Mansfield, Lorelle M.; Garris, Rebekah L.; Counts, Kahl D.

Cu(In, Ga)Se2 (CIGS)-based solar cells from six fabricators were characterized and compared. The devices had differing substrates, absorber deposition processes, buffer materials, and contact materials. The effective bandgaps of devices varied from 1.05 to 1.22 eV, with the lowest optical bandgaps occurring in those with metal-precursor absorber processes. Devices with Zn(O, S) or thin CdS buffers had quantum efficiencies above 90% down to 400 nm. Most voltages were 250-300 mV below the Shockley-Queisser limit for their bandgap. Electroluminescence intensity tracked well with the respective voltage deficits. Fill factor (FF) was as high as 95% of the maximum for each device'smore » respective current and voltage, with higher FF corresponding to lower diode quality factors (~1.3). An in-depth analysis of FF losses determined that diode quality reflected in the quality factor, voltage-dependent photocurrent, and, to a lesser extent, the parasitic resistances are the limiting factors. As a result, different absorber processes and device structures led to a range of electrical and physical characteristics, yet this investigation showed that multiple fabrication pathways could lead to high-quality and high-efficiency solar cells.« less

Clarifying the Links Among Online Gaming, Internet Use, Drinking Motives, and Online Pornography Use.

PubMed

Bőthe, Beáta; Tóth-Király, István; Orosz, Gábor

2015-04-01

This study was aimed at investigating the links between online gaming and online pornography use by considering gender, problematic Internet use, and different motives for alcohol drinking. University students (n=512; mean age=22.11 years; standard deviation=2.43 years; 64.06 percent women) filled in the Cyber Pornography Use Inventory, Hungarian version, the Problematic Online Gaming Questionnaire, Hungarian version (POGQ-HU), the Problematic Internet Use Questionnaire, Hungarian version (PIUQ-HU), and the Drinking Motive Questionnaire Revised Short Form, Hungarian version (DMQ-R-HU SF) questionnaires. According to hierarchical multiple regression analyses, the neglect factor of PIUQ-HU, the conformity factor of DMQ-R-HU SF, and the immersion and preoccupation factors of POGQ-HU have a significant predictive value on one's online pornography use, but gender does not. This research shows that independently from the effect of Internet and alcohol use dimensions, immersion and preoccupation factors of online gaming have significant effects on online pornography use. However, preoccupation has a negative effect on pornography use. Players scoring high on this subscale may think about gaming as the only interesting activity that rates higher than even pornography.

Performance analysis of higher mode spoof surface plasmon polariton for terahertz sensing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Yao, Haizi; Tu, Wanli; Zhong, Shuncong, E-mail: zhongshuncong@hotmail.com

2015-04-07

We investigated the spoof surface plasmon polaritons (SSPPs) on 1D grooved metal surface for terahertz sensing of refractive index of the filling analyte through a prism-coupling attenuated total reflection setup. From the dispersion relation analysis and the finite element method-based simulation, we revealed that the dispersion curve of SSPP got suppressed as the filling refractive index increased, which cause the coupling resonance frequency redshifting in the reflection spectrum. The simulated results for testing various refractive indexes demonstrated that the incident angle of terahertz radiation has a great effect on the performance of sensing. Smaller incident angle will result in amore » higher sensitive sensing with a narrower detection range. In the meanwhile, the higher order mode SSPP-based sensing has a higher sensitivity with a narrower detection range. The maximum sensitivity is 2.57 THz/RIU for the second-order mode sensing at 45° internal incident angle. The proposed SSPP-based method has great potential for high sensitive terahertz sensing.« less

Predictors of Intervention Success in a Sports-Based Program for Adolescents at Risk of Juvenile Delinquency

PubMed Central

Spruit, Anouk; van der Put, Claudia; van Vugt, Eveline; Stams, Geert Jan

2017-01-01

To prevent juvenile delinquency, there is growing interest in the use of sports-based interventions. To date, there is little empirical research that provides insights into for whom, how, and when sports-based crime prevention programs are most effective. Therefore, the current study assessed which youth, coach, and context factors were predictive of change in risk factors and protective factors for delinquency in a sports-based crime prevention program for at-risk adolescents. Participants (N = 155) and their teachers filled in questionnaires about risk and protective factors for delinquency at the start of the intervention and 13 months later. In addition, the coaches and participants filled in questionnaires about the predictors of intervention success. The youths showed significant improvements over the course of the intervention. Various youth, coach, and context factors (e.g., the type of education of youth and the sociomoral climate at the sports club) were associated to change in the outcome variables. PMID:28741394

Predictors of Intervention Success in a Sports-Based Program for Adolescents at Risk of Juvenile Delinquency.

PubMed

Spruit, Anouk; van der Put, Claudia; van Vugt, Eveline; Stams, Geert Jan

2018-05-01

To prevent juvenile delinquency, there is growing interest in the use of sports-based interventions. To date, there is little empirical research that provides insights into for whom, how, and when sports-based crime prevention programs are most effective. Therefore, the current study assessed which youth, coach, and context factors were predictive of change in risk factors and protective factors for delinquency in a sports-based crime prevention program for at-risk adolescents. Participants ( N = 155) and their teachers filled in questionnaires about risk and protective factors for delinquency at the start of the intervention and 13 months later. In addition, the coaches and participants filled in questionnaires about the predictors of intervention success. The youths showed significant improvements over the course of the intervention. Various youth, coach, and context factors (e.g., the type of education of youth and the sociomoral climate at the sports club) were associated to change in the outcome variables.

Dental caries and preterm birth: a systematic review and meta-analysis.

PubMed

Wagle, Madhu; D'Antonio, Francesco; Reierth, Eirik; Basnet, Purusotam; Trovik, Tordis A; Orsini, Giovanna; Manzoli, Lamberto; Acharya, Ganesh

2018-03-02

The primary objective of this systematic review was to evaluate the association between dental caries and preterm birth (PTB). The secondary objective was ascertaining the difference between women with dental caries who experienced PTB and those who did not with regard to decayed, missing and filled teeth (DMFT), and decayed, missing and filled surfaces (DMFS) indices. MEDLINE, Embase, CINAHL and Cochrane databases were searched initially in November 2015 and repeated in December 2016. We included observational cohort and case-control studies. Only studies reporting the risk of PTB in women affected compared with those not affected by dental caries in pregnancy were included. Random-effect meta-analyses were used to compute the summary OR of PTB among women with caries versus women without caries, and the mean difference in either DMFT or DMFS indices between women experiencing PTB and those without PTB. Nine observational studies (4826 pregnancies) were included. Women affected by dental caries during pregnancy did not show a significantly higher risk of PTB (OR: 1.16, 95% CI 0.90 to 1.49, P=0.25, I 2 =35%). Also, the women with PTB did not show significantly higher DMFT or DMFS indices (summary mean differences: 1.56, P=0.10; I 2 =92% and -0.15, P=0.9, I 2 =89%, respectively). Dental caries does not appear to be a substantial risk factor for PTB. NCT01675180; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Comparison of hardness of three temporary filling materials cured by two light-curing devices.

PubMed

Bodrumlu, E; Koçak, M M; Hazar Bodrumlu, E; Ozcan, S; Koçak, S

2014-01-01

Polymerization ability of light-curing devices can affect the light-cured material hardness. The purpose of the present study was to evaluate and compare the hardness of three temporary filling materials that had been light-cured by either a light emitting diode (LED) or a halogen light-curing unit. The temporary filling materials, First Fill, Voco Clip and Bioplic, were placed in wells in a Teflon plate. The 24 specimens of each material were divided into two groups (N.=12/group) for photo-activation by either of the two light-curing units. The LED or halogen device was applied for 40s to the top surface of each specimen. A Knoop hardness test was performed on the top and bottom surface of each specimen, with five measurements per specimen. The highest hardness values for both the LED and halogen treated groups were observed for First Fill and the lowest values were for Voco Clip in top and bottom surfaces. The hardness obtained for the three materials with the halogen unit were significantly higher than the values obtained with the LED unit in both surfaces (P<0.05). First Fill light-cured temporary material exhibited the highest hardness values on the top and bottom surfaces than Voco Clip and Bioplic temporary materials. The hardness of light-cured temporary filling materials can be affected by the type of light-curing unit.

The Shock and Vibration Digest. Volume 18, Number 1

DTIC Science & Technology

1986-01-01

polyurethanes reduced the loss factor and emphasized the correlation between molecular storage modulus by increasing the length of the structure and...one tempera- static deformations. He gave storage and loss ture/frequency range is difficult with copoly- moduli for a carbon black filled and an...has been described (18). The shear loss author states that the frequency dependence of and storage moduli of a void-filled polyurethane the elastomers

Distance descending ordering method: An O(n) algorithm for inverting the mass matrix in simulation of macromolecules with long branches

NASA Astrophysics Data System (ADS)

Xu, Xiankun; Li, Peiwen

2017-11-01

Fixman's work in 1974 and the follow-up studies have developed a method that can factorize the inverse of mass matrix into an arithmetic combination of three sparse matrices-one of them is positive definite and needs to be further factorized by using the Cholesky decomposition or similar methods. When the molecule subjected to study is of serial chain structure, this method can achieve O (n) time complexity. However, for molecules with long branches, Cholesky decomposition about the corresponding positive definite matrix will introduce massive fill-in due to its nonzero structure. Although there are several methods can be used to reduce the number of fill-in, none of them could strictly guarantee for zero fill-in for all molecules according to our test, and thus cannot obtain O (n) time complexity by using these traditional methods. In this paper we present a new method that can guarantee for no fill-in in doing the Cholesky decomposition, which was developed based on the correlations between the mass matrix and the geometrical structure of molecules. As a result, the inverting of mass matrix will remain the O (n) time complexity, no matter the molecule structure has long branches or not.

SALT-RESPONSIVE ERF1 is a negative regulator of grain filling and gibberellin-mediated seedling establishment in rice.

PubMed

Schmidt, Romy; Schippers, Jos H M; Mieulet, Delphine; Watanabe, Mutsumi; Hoefgen, Rainer; Guiderdoni, Emmanuel; Mueller-Roeber, Bernd

2014-02-01

Grain quality is an important agricultural trait that is mainly determined by grain size and composition. Here, we characterize the role of the rice transcription factor (TF) SALT-RESPONSIVE ERF1 (SERF1) during grain development. Through genome-wide expression profiling and chromatin immunoprecipitation, we found that SERF1 directly regulates RICE PROLAMIN-BOX BINDING FACTOR (RPBF), a TF that functions as a positive regulator of grain filling. Loss of SERF1 enhances RPBF expression resulting in larger grains with increased starch content, while SERF1 overexpression represses RPBF resulting in smaller grains. Consistently, during grain filling, starch biosynthesis genes such as GRANULE-BOUND STARCH SYNTHASEI (GBSSI), STARCH SYNTHASEI (SSI), SSIIIa, and ADP-GLUCOSE PYROPHOSPHORYLASE LARGE SUBUNIT2 (AGPL2) are up-regulated in SERF1 knockout grains. Moreover, SERF1 is a direct upstream regulator of GBSSI. In addition, SERF1 negatively regulates germination by controlling RPBF expression, which mediates the gibberellic acid (GA)-induced expression of RICE AMYLASE1A (RAmy1A). Loss of SERF1 results in more rapid seedling establishment, while SERF1 overexpression has the opposite effect. Our study reveals that SERF1 represents a negative regulator of grain filling and seedling establishment by timing the expression of RPBF.

Effect of using acetone and distilled water on the performance of open loop pulsating heat pipe (OLPHP) with different filling ratios

NASA Astrophysics Data System (ADS)

Rahman, Md. Lutfor; Afrose, Tonima; Tahmina, Halima Khatun; Rinky, Rumana Parvin; Ali, Mohammad

2016-07-01

Pulsating heat pipe (PHP) is a new innovation in the modern era of miniaturizes thermal management system for its higher heating and cooling capacity. The objective of this experiment is to observe the performance of open loop pulsating heat pipe using two fluids at different filling ratios. This OLPHP is a copper capillary tube of 2.5mm outer diameter and 2mm inner diameter. It consists of 8 loops where the evaporative section is 50mm, adiabatic section is 120mm and condensation section is 80mm. The experiment is conducted with distilled water and acetone at 40%, 50%, 60%, and 70% filling ratios where 0° (vertical) is considered as definite angle of inclination. Distilled water and acetone are selected as working fluids considering their different latent heat of vaporization and surface tension. It is found that acetone shows lower thermal resistance than water at all heat inputs. Best performance of acetone is attained at 70% filling ratio. Water displays better heat transfer capability at 50% filling ratio.

Influence of filling-drawdown cycles of the Vajont reservoir on Mt. Toc slope stability

NASA Astrophysics Data System (ADS)

Paronuzzi, Paolo; Rigo, Elia; Bolla, Alberto

2013-06-01

In the present work, the 1963 Vajont landslide has been back-analyzed in detail to examine the influence of reservoir operations (filling and drawdown) on Mt. Toc slope stability. The combined seepage-slope stability analyses carried out show that the main destabilizing factor that favored the 1963 Vajont landslide was the reservoir-induced water table that formed as a consequence of rapid seepage inflow within the submerged toe of the slope — decrease in the factor of safety (FOS) up to 12% compared to the initial slope stability condition, i.e., in the absence of the Vajont reservoir. Rainfall would only have been a decisive factor if the initial stability condition of the Mt. Toc slope had already been very close to failure (decrease in FOS caused by heavy or prolonged rainfall is about 3-4%, for the worst case scenario analyzed). The permeability of the shear zone material occurring at the base of the prehistoric Vajont rockslide has been evaluated at 5 × 10- 4 m/s, and back-calculated values of the friction angles Φ range from 17.5° to 27.5°. When considering mountain reservoirs, slope failures can occur during both filling and drawdown phases. In the Vajont case, owing to the highly permeable materials of the shear zone, slope stability decreased during filling and increased during drawdown. Another displacement-dependent phenomenon of a mechanical nature - progressive failure of the NE landslide constraint - has to be considered to understand the slope collapse that occurred during the last drawdown (26 September-9 October 1963). The results of the combined seepage-slope stability models indicate that permeability of bank-forming material and filling-drawdown rates of reservoirs can strongly influence slope stability. Slow lowering of the reservoir level is a necessary measure to reduce the occurrence of very dangerous transient negative peaks of FOS.

Possible health effects of liquefied petroleum gas on workers at filling and distribution stations of Gaza governorates.

PubMed

Sirdah, M M; Al Laham, N A; El Madhoun, R A

2013-03-01

Liquefied petroleum gas (LPG) is widely used in the Gaza Strip for domestic purposes, in agriculture and industry and, illegally, in cars. This study aimed to identify possible health effects on workers exposed to LPG in Gaza governorates. Data were collected by a questionnaire interview, and haematological and biochemical analyses of venous blood samples were made from 30 workers at filling and distribution stations and 30 apparently healthy controls. Statistically significant differences were found in all self-reported health-related complaints among LPG workers versus controls. LPG workers had significantly higher values of red blood cell counts, haemoglobin, haematocrit mean corpuscular haemoglobin and platelet counts. They also had significantly higher values of kidney function tests (urea, creatinine and uric acid) and liver function enzyme activities (aspartate aminotransferase and alanine aminotransferase). LPG workers at Gaza Strip petroleum stations are at higher risk for health-related symptoms and clinical abnormalities.

Burrowing inhibition by fine textured beach fill: Implications for recovery of beach ecosystems

NASA Astrophysics Data System (ADS)

Viola, Sloane M.; Hubbard, David M.; Dugan, Jenifer E.; Schooler, Nicholas K.

2014-10-01

Beach nourishment is often considered the most environmentally sound method of maintaining eroding shorelines. However, the ecological consequences are poorly understood. Fill activities cause intense disturbance and high mortality and have the potential to alter the diversity, abundance, and distribution of intertidal macroinvertebrates for months to years. Ecological recovery following fill activities depends on successful recolonization and recruitment of the entire sandy intertidal community. The use of incompatible sediments as fill material can strongly affect ecosystem recovery. We hypothesized that burrowing inhibition of intertidal animals by incompatible fine fill sediments contributes to ecological impacts and limits recovery in beach ecosystems. We experimentally investigated the influence of intertidal zone and burrowing mode on responses of beach invertebrates to altered sediment texture (28-38% fines), and ultimately the potential for colonization and recovery of beaches disturbed by beach filling. Using experimental trials in fill material and natural beach sand, we found that the mismatched fine fill sediments significantly inhibited burrowing of characteristic species from all intertidal zones, including sand crabs, clams, polychaetes, isopods, and talitrid amphipods. Burrowing performance of all five species we tested was consistently reduced in the fill material and burrowing was completely inhibited for several species. The threshold for burrowing inhibition by fine sediment content in middle and lower beach macroinvertebrates varied by species, with highest sensitivity for the polychaete (4% fines, below the USA regulatory limit of 10% fines), followed by sand crabs and clams (20% fines). These results suggest broader investigation of thresholds for burrowing inhibition in fine fill material is needed for beach animals. Burrowing inhibition caused by mismatched fill sediments exposes beach macroinvertebrates to stresses, which could depress recruitment and survival at all intertidal zones. Our results suggest use of incompatible fine fill sediments from dredging projects creates unsuitable intertidal habitat that excludes burrowing macroinvertebrates and could delay beach ecosystem recovery. Through effects on beach invertebrates that are prey for shorebirds and fish, the ecological impacts of filling with mismatched fine sediments could influence higher trophic levels and extend beyond the beach itself.

Predictors of Increased Left Ventricular Filling Pressure in Dialysis Patients with Preserved Left Ventricular Ejection Fraction

PubMed Central

Bajraktari, Gani; Berbatovci-Ukimeraj, Mimoza; Hajdari, Ali; Ibraimi, Lavdim; Daullxhiu, Irfan; Elezi, Ymer; Ndrepepa, Gjin

2009-01-01

Aim To study the left and right ventricular function and to assess the predictors of increased left ventricular (LV) filling pressure in dialysis patients with preserved LV ejection fraction. Methods This study included 63 consecutive patients (age 57 ± 14 years, 57% women) with end-stage renal failure. Echocardiography, including tissue Doppler measurements, was performed in all patients. Based on the median value of the ratio of transmitral early diastolic velocity to early myocardial velocity (E/E’ ratio), patients were divided into 2 groups: the group with high filling pressure (E/E’>10.16) and the group with low filling pressure (E/E’≤10.16). Results Compared with patients with low filling pressure, the group of patients with high filling pressure included a higher proportion of diabetic patients (41% vs 13%, P = 0.022) and had greater LV mass index (211 ± 77 vs 172 ± 71 g/m3, P = 0.04), lower LV lateral long axis amplitude (1.4 ± 0.3 vs 1.6 ± 0.3 cm, P = 0.01), higher E wave (84 ± 19 vs 64 ± 18cm/s, P < 0.001), lower systolic myocardial velocity (S’:8.6 ± 1.5 vs 7.0 ± 1.3 cm/s, P < 0.001), and lower diastolic myocardial velocities (E’: 6.3 ± 1.9 vs 9.5 ± 2.9 cm/s, P < 0.001; A’: 8.4 ± 1.9 vs 9.7 ± 2.5 cm/s, P = 0.018). Multivariate analysis identified LV systolic myocardial velocity – S’ wave (adjusted odds ratio, 1.909; 95% confidence interval, 1.060-3.439; P = 0.031) and age (1.053; 1.001-1.108; P = 0.048) as the only independent predictors of high LV filling pressure in dialysis patients. Conclusions In dialysis patients with preserved left ventricular ejection fraction, reduced systolic myocardial velocity and elderly age are independent predictors of increased left ventricular filling pressure. PMID:20017222

Effect of layer thickness on the elution of bulk-fill composite components.

PubMed

Rothmund, Lena; Reichl, Franz-Xaver; Hickel, Reinhard; Styllou, Panorea; Styllou, Marianthi; Kehe, Kai; Yang, Yang; Högg, Christof

2017-01-01

An increment layering technique in a thickness of 2mm or less has been the standard to sufficiently convert (co)monomers. Bulk fill resin composites were developed to accelerate the restoration process by enabling up to 4mm thick increments to be cured in a single step. The aim of the present study is to investigate the effect of layer thickness on the elution of components from bulk fill composites. The composites ELS Bulk fill, SDR Bulk fill and Venus Bulkfill were polymerized according to the instruction of the manufacturers. For each composite three groups with four samples each (n=4) were prepared: (1) samples with a layer thickness of 2mm; (2) samples with a layer thickness of 4mm and (3) samples with a layer thickness of 6mm. The samples were eluted in methanol and water for 24h and 7 d. The eluates were analyzed by gas chromatography/mass spectrometry (GC/MS). A total of 11 different elutable substances have been identified from the investigated composites. Following methacrylates showed an increase of elution at a higher layer thickness: TEGDMA (SDR Bulk fill, Venus Bulk fill), EGDMA (Venus Bulk fill). There was no significant difference in the elution of HEMA regarding the layer thickness. The highest concentration of TEGDMA was 146μg/mL for SDR Bulk fill at a layer thickness of 6mm after 7 d in water. The highest HEMA concentration measured at 108μg/mL was detected in the methanol eluate of Venus Bulk fill after 7 d with a layer thickness of 6mm. A layer thickness of 4mm or more can lead to an increased elution of some bulk fill components, compared to the elution at a layer thickness of 2mm. Copyright © 2016 The Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Performance analysis of no-vent fill process for liquid hydrogen tank in terrestrial and on-orbit environments

NASA Astrophysics Data System (ADS)

Wang, Lei; Li, Yanzhong; Zhang, Feini; Ma, Yuan

2015-12-01

Two finite difference computer models, aiming at the process predictions of no-vent fill in normal gravity and microgravity environments respectively, are developed to investigate the filling performance in a liquid hydrogen (LH2) tank. In the normal gravity case model, the tank/fluid system is divided into five control volume including ullage, bulk liquid, gas-liquid interface, ullage-adjacent wall, and liquid-adjacent wall. In the microgravity case model, vapor-liquid thermal equilibrium state is maintained throughout the process, and only two nodes representing fluid and wall regions are applied. To capture the liquid-wall heat transfer accurately, a series of heat transfer mechanisms are considered and modeled successively, including film boiling, transition boiling, nucleate boiling and liquid natural convection. The two models are validated by comparing their prediction with experimental data, which shows good agreement. Then the two models are used to investigate the performance of no-vent fill in different conditions and several conclusions are obtained. It shows that in the normal gravity environment the no-vent fill experiences a continuous pressure rise during the whole process and the maximum pressure occurs at the end of the operation, while the maximum pressure of the microgravity case occurs at the beginning stage of the process. Moreover, it seems that increasing inlet mass flux has an apparent influence on the pressure evolution of no-vent fill process in normal gravity but a little influence in microgravity. The larger initial wall temperature brings about more significant liquid evaporation during the filling operation, and then causes higher pressure evolution, no matter the filling process occurs under normal gravity or microgravity conditions. Reducing inlet liquid temperature can improve the filling performance in normal gravity, but cannot significantly reduce the maximum pressure in microgravity. The presented work benefits the understanding of the no-vent fill performance and may guide the design of on-orbit no-vent fill system.

TiO2-ZnS Cascade Electron Transport Layer for Efficient Formamidinium Tin Iodide Perovskite Solar Cells.

PubMed

Ke, Weijun; Stoumpos, Constantinos C; Logsdon, Jenna Leigh; Wasielewski, Michael R; Yan, Yanfa; Fang, Guojia; Kanatzidis, Mercouri G

2016-11-16

Achieving high open-circuit voltage (V oc ) for tin-based perovskite solar cells is challenging. Here, we demonstrate that a ZnS interfacial layer can improve the V oc and photovoltaic performance of formamidinium tin iodide (FASnI 3 ) perovskite solar cells. The TiO 2 -ZnS electron transporting layer (ETL) with cascade conduction band structure can effectively reduce the interfacial charge recombination and facilitate electron transfer. Our best-performing FASnI 3 perovskite solar cell using the cascaded TiO 2 -ZnS ETL has achieved a power conversion efficiency of 5.27%, with a higher V oc of 0.380 V, a short-circuit current density of 23.09 mA cm -2 , and a fill factor of 60.01%. The cascade structure is further validated with a TiO 2 -CdS ETL. Our results suggest a new approach for further improving the performance of tin-based perovskite solar cells with a higher V oc .

A Science-Based Understanding of Cermet Processing

DOE Office of Scientific and Technical Information (OSTI.GOV)

Cesarano, III, Joseph; Roach, Robert Allen; Kilgo, Alice C.

2006-04-01

This report is a summary of the work completed in FY01 for science-based characterization of the processes used to fabricate 1) cermet vias in source feedthrus using slurry and paste-filling techniques and 2) cermet powder for dry pressing. Common defects found in cermet vias were characterized based on the ability of subsequent processing techniques (isopressing and firing) to remove the defects. Non-aqueous spray drying and mist granulation techniques were explored as alternative methods of creating CND50, the powder commonly used for dry pressed parts. Compaction and flow characteristics of these techniques were analyzed and compared to standard dry-ball-milled CND50. Duemore » to processing changes, changes in microstructure can occur. A microstructure characterization technique was developed to numerically describe cermet microstructure. Machining and electrical properties of dry pressed parts were also analyzed and related to microstructure using this analytical technique.3 Executive SummaryThis report outlines accomplishments in the science-based understanding of cermet processing up to fiscal year 2002 for Sandia National Laboratories. The three main areas of work are centered on 1) increasing production yields of slurry-filled cermets, 2) evaluating the viability of high-solids-loading pastes for the same cermet components, and 3) optimizing cermet powder used in pressing processes (CND50). An additional development that was created as a result of the effort to fully understand the impacts of alternative processing techniques is the use of analytical methods to relate microstructure to physical properties. Recommendations are suggested at the end of this report. Summaries of these four efforts are as follows:1.Increase Production Yields of Slurry-Filled Cermet Vias Finalized slurry filling criteria were determined based on three designs of experiments where the following factors were analyzed: vacuum time, solids loading, pressure drop across the filter paper, slurry injection rate, via prewetting, slurry injection angle, filter paper prewetting, and slurry mixing time. Many of these factors did not have an influence on defect formation. In order of decreasing importance, critical factors for defect formation by slurry filling are vacuum time (20 sec. optimal), slurry solids loading (20.0 g of cermet with 13.00 g of DGBEA solvent (21.2 vol%)), filling with the pipette in a vertical position, and faster injection rates (%7E765 l/s) as preferable to slower. No further recommendations for improvement to this process can be suggested. All findings of the slurry filling process have been transferred to CeramTec, the supplier. Paste filling methods appear to show more promise of increasing production yields. The types of flaws commonly found in slurry-filled vias were identified and followed throughout the entire source feedthru process. In general, all sizes of cracks healed during isopressing and firing steps. Additionally, small to medium sized voids (less than 1/3 the via diameter) can be healed. Porosity will usually lead to via necking, which may cause the part to be out of specification. Large voids (greater 4 than 1/3 of the diameter) and partial fills are not healed or produce significant necking. 2.Viability of High-Solids-Loading-Cermet Paste for Filling Source Feedthru ViaThe paste-filling process is easy to implement and easier to use. The high solids loading (>40 vol %) reduces the incidence of drying defects, which are seen in slurry filled (%7E23 vol %) vias. Additionally, the way in which the vias are filled (the paste is pushed from entrance to exit, displacing air as the paste front progresses), reduces the chance of entrapped voids, which are common in the slurry filling process. From the fair number of samples already filled, the likelihood of this process being a viable and reliable process is very good. Issues of concern for the paste process, as with any new process, are any problems that may arise in subsequent manufacturing stages of the neutron tube that may be affected by subtle changes in microstructure. Both MC4277 and MC4300-type source feedthrus were paste-filled by hand. X-ray analysis showed a much lower existence of voids in the green parts as compared to slurry-filled parts. The paste shows improvements in shelf life (weeks) as compared to slurry (minutes). This method of introducing the cermet to the via also lends itself very well to an automated filling process where a machine can either drill vias or, with the aid of a vision system, find pre-drilled vias and fill them with paste. The pastes used in this work prove the concept of this automated filling process as MC4277 sources have been filled using such a prototype machine, however, better performing pastes can be developed which are less hazardous (aqueous systems). The paste process was also used to successfully fill MC4300 "dogleg" type sources.3.Optimize CND50 Two methods of creating granulated cermet powder for comparison with dry-ball milled CND50 were explored. The first method, non-aqueous spray drying, was performed at Niro Inc. used a 40/60 (wt %) ethanol/toluene solvent and three binder systems; polyvinyl butyral (B79), ethylcellulose (Ethocel), and hydroxypropylcellulose (Klucel). Due to the nature of small spray-dry systems, an excess amount of fines was present in the granulated powder, which may have contributed to the low angles of repose (68 to 78). This is a moderate increase in 5 flowability as standard dry-ball milled powder possesses an angle of repose of 79-89. Mist granulated powders were produced with a tert-butanol solvent and polyvinyl butyral binder system. The angles of repose were more promising (28). More investigation into the mist granulation method is required. Also, aqueous spray drying may be possible with cermet and should be explored. Compaction of all granulated powders is much closer to a proven pressing powder (Sandi94 - angle of repose 29) which should allow cermet to be pressed to near net shape where die filling is difficult for non-flowing powders.4.Microstructure Characterization An analytical technique was developed to numerically characterize microstructures in terms of molybdenum dispersion, homogeneity, and percolation indices. This technique was applied to dry-ball-milled samples of various ball-milling times (0.5 to 20 hours). Significant change in the microstructure could be seen with milling time. Increased milling time caused agglomeration of molybdenum particles, increasing the percolation index, whereas short milling times promoted higher dispersion indices. This phenomenon is contrary to conventional understanding of mixing. However, conventional ball milling does not usually incorporate granules with binder and separate particles. This discrepancy may explain the odd mixing behavior. It is important to note that the high percolation index possessed by long ball mill times showed lower electrical resistance than low-percolation-index microstructures. However, machinability of high percolation, low-dispersion-index microstructures were poor as compared to microstructures with high dispersion indices and moderate percolation indices. This trade-off between dispersion and percolation (at constant molybdenum levels) suggests that microstructures can be achieved that posses good mechanical and electrical properties. Coincidentally, microstructures that satisfy this condition are produced by the standard dry-ball-milled CND50 (4 hour ball mill time). The performance and sensitivity of the microstructure characterization technique should be evaluated, specifically for electrical conductivity. Processing techniques to decrease the percolation index (lowering molybdenum content, excess ball milling, 6 larger molybdenum particles, etc.) should be employed to determine the point where cermet is not conductive or falls below electrical conduction specifications.7« less

Rangewide determinants of population performance in Prunus lusitanica: Lessons for the contemporary conservation of a Tertiary relict tree

NASA Astrophysics Data System (ADS)

Pardo, Adara; Cáceres, Yonatan; Pulido, Fernando

2018-01-01

Relict species are an extremely important part of biodiversity and as such studies on the factors that allow their current persistence are required. The aim of this study was to assess the determinants of the distribution and range-wide population performance of the Tertiary relict tree Prunus lusitanica L. This threatened species is confined to Iberia, Northern Morocco and Macaronesia with a fragmented and scattered distribution. Using ecological niche modelling, we calculated the level of range filling across the range and tested its relationship with human impact. We then assessed the relative importance of climatic suitability as obtained through niche modelling, topographic factors and contemporary human impact on range-wide population performance. Results showed that the species occupies only 2.4% of the overall area predicted to be climatically suitable for its presence and the level of range filling varied across regions. A weak negative relationship among range filling and human impact was found. Overall climatic suitability was the strongest predictor of population performance. However, it showed high variability across regions: the effect was positive in Iberia whereas negative but not significant in Macaronesia and Morocco. Human impact showed a significant negative effect and finally topographic factors such as altitude had a minor negative effect. Our results highlight that both climate and human impact play a major role in the current limited range filling and performance of the species. Management plans to minimize anthropogenic disturbances together with reforestation measures are urgently needed in order to conserve this unique species.

Geomorphic controls on fluvial carbon exports and emissions from upland swamps in eastern Australia.

PubMed

Cowley, Kirsten; Looman, Arun; Maher, Damien T; Fryirs, Kirstie

2018-03-15

Temperate Highland Peat Swamps on Sandstone (THPSS) are upland wetlands, similar to fens in the Northern Hemisphere and are found at the headwaters of low-order streams on the plateaus of Eastern Australia. They are classified as endangered ecological communities under State and National legislation. Previous works have identified particular geomorphic characteristics that are important to carbon storage in these low energy sediment accumulation zones. Changes in the geomorphic structure of THPSS, such as channelisation, may have profound implications for carbon storage. To assess the effect of channelisation on carbon budgets in these ecosystems it is essential to identify and quantify differences in carbon export, emissions and stocks of carbon of intact swamps and those that have become channelised. We undertook seasonal sampling of the perched swamp aquifers and surface waters of two intact swamps and two channelised fills in the Blue Mountains of New South Wales, Australia, to investigate differences in carbon exports and emissions between the two swamp types. We found that channelised fills' mean CO 2 emissions were almost four times higher than intact swamps with mean CH 4 emissions up to five times higher. Annual fluvial carbon exports for channelised fills were up to 18 times that of intact swamps. Channelised fill exports and emissions can represent up to 2% of the total swamp carbon stocks per annum which is 40 times higher than the intact swamps. This work clearly demonstrates that changes in geomorphic structure brought about by incision and channelisation results in profound changes to the carbon storage function of THPSS. Copyright © 2017 Elsevier B.V. All rights reserved.

Determination of homologous distributions of bisEMA dimethacrylates in bulk-fill resin-composites by GC-MS.

PubMed

Durner, Jürgen; Schrickel, Klaus; Watts, David C; Ilie, Nicoleta

2015-04-01

Ethoxylated bisphenol A dimethacrylate (bisEMA) is a basis monomer in several dental resin composites. It was the aim of the present study to develop a method allowing detection of bisEMA and its different degrees of ethoxylation eluted from polymerized resin composites. High-temperature gas chromatography/mass spectrometry (HT-GC/MS) by direct on-column injection was used to identify ethoxylated bisEMA in ethanol/water (3:1) eluates from polymerized specimen of four bulk-fill resin composites - Venus(®) bulk fill, Surefil(®) SDR™ flow, Filtek™ Bulk Fill and Sonic Fill™. Additionally, the unpolymerised pastes were analysed. The developed method allowed identification of a homologous series of bisEMA up to twelve ethoxy groups in the unpolymerised materials. The molecular masses of the homologous bisEMA varied between 452 g/mol and 892 g/mol and were detected for retention times from 9.43 min to 13.36 min. Analysis of eluates from polymerised materials identified bisEMA monomers with less than 6 ethoxy groups. Chromatograms showed larger peak areas for the lower volatile bisEMA with 4-6 ethoxy groups compared with higher volatile bisEMA with 2 or 3 ethoxy groups, thus indicating that the amounts of these homologues in the pastes were higher. Ethoxylated bisEMA with up to twelve ethoxy groups can be identified by HT-GC/MS. In all eluates bisEMA was found. The higher the number of ethoxy groups the lower are the peak areas from bisEMA in the gas chromatogram. These findings may be significant for toxicological analysis of resin-composites incorporating bis-EMA. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

Dual Enrollment from Two Points of View: Higher Education and K-12

ERIC Educational Resources Information Center

Kilgore, Wendy; Wagner, Ellen

2017-01-01

While dual enrollment fills a similar student success niche in both higher and K-12 education, the administrative perspectives of these two entities do not always align. This article highlights the groups' similarities and differences in perspective and proposes implications for practice.

Special Issue: Philanthropy and Fundraising in American Higher Education

ERIC Educational Resources Information Center

Drezner, Noah D.

2011-01-01

This monograph examines the philanthropic contributions of individuals through the existing literature and proposes future philanthropic and fundraising research that can help fill the theoretical void in the literature, thereby improving future research and fundraising in higher education. It covers the major approaches, topics, and theories…

Factors associated with dental caries in a group of American Indian children at age 36 months.

PubMed

Warren, John J; Blanchette, Derek; Dawson, Deborah V; Marshall, Teresa A; Phipps, Kathy R; Starr, Delores; Drake, David R

2016-04-01

Early childhood caries (ECC) is rampant among American Indian children, but there has been relatively little study of this problem. This article reports on risk factors for caries for a group of American Indian children at age 36 months as part of a longitudinal study. Pregnant women from a Northern Plains Tribal community were recruited to participate in a longitudinal study of caries and caries risk factors. Standardized dental examinations were completed on children, and questionnaires were completed by mothers at baseline and when children were 4, 8, 12, 16, 22, 28, and 36 months of age. Examinations were surface-specific for dental caries, and the questionnaires collected data on demographic, dietary, and behavioral factors. Nonparametric bivariate tests and logistic regression models were used to identify risk factors for caries at 36 months, and negative binomial regression was used to identify factors related to caries severity (dmf counts). Among the 232 children, and caries prevalence for cavitated lesions was 80%, with an additional 15% having only noncavitated lesions. The mean dmfs was 9.6, and of the total dmfs, nearly 62% of affected surfaces were decayed, 31% were missing, and 7% were filled. Logistic regression identified higher added-sugar beverage consumption, younger maternal age at baseline, higher maternal DMFS at baseline, and greater number of people in the household as significant (P < 0.05) risk factors. Negative binomial regression found that only maternal DMFS was associated with child dmf counts. By the age of 36 months, dental caries is nearly universal in this population of American Indian children. Caries risk factors included sugared beverage consumption, greater household size, and maternal factors, but further analyses are needed to better understand caries in this population. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Slotted Polyimide-Aerogel-Filled-Waveguide Arrays

NASA Technical Reports Server (NTRS)

Rodriguez-Solis, Rafael A.; Pacheco, Hector L.; Miranda, Felix A.; Meador, Mary Ann B.

2013-01-01

This presentation discussed the potential advantages of developing Slotted Waveguide Arrays using polyimide aerogels. Polyimide (PI) aerogels offer great promise as an enabling technology for lightweight aerospace antenna systems. PI aerogels are highly porous solids possessing low density and low dielectric permittivity combined with good mechanical properties. For slotted waveguide array applications, there are significant advantages in mass that more than compensate for the slightly higher loss of the aerogel filled waveguide when compared to state of practice commercial waveguide.

Substantiation of artificial composite-structure roof construction in top-down cut-and-fill stoping

NASA Astrophysics Data System (ADS)

Rukavishnikov, GD; Neverov, SA; Neverov, AA

2018-03-01

It has been found efficient and safe to use top-down cut-and-fill stoping with saving of the artificial backfill cost and material through the use of a solid nonuniform material composed of two components (layers). It is shown that the artificial roof can be advanced after a stope without essential change in the stope condition as compared with the classical top-down slice method, which provides higher safety of mining.

Demonstrated high performance of gas-filled rugby-shaped hohlraums on Omega

NASA Astrophysics Data System (ADS)

Philippe, F.; Tassin, V.; Depierreux, S.; Gauthier, P.; Masson-Laborde, P. E.; Monteil, M. C.; Seytor, P.; Villette, B.; Lasinski, B.; Park, H. S.; Ross, J. S.; Amendt, P.; Döppner, T.; Hinkel, D. E.; Wallace, R.; Williams, E.; Michel, P.; Frenje, J.; Gatu-Johnson, M.; Li, C. K.; Petrasso, R.; Glebov, V.; Sorce, C.; Stoeckl, C.; Nikroo, A.; Giraldez, E.

2014-07-01

A direct experimental comparison of rugby-shaped and cylindrical shaped gas-filled hohlraums on the Omega laser facility demonstrates that higher coupling and minimal backscatter can be achieved in the rugby geometry, leading to significantly enhanced implosion performance. A nearly 50% increase of x-ray drive is associated with earlier bangtime and increase of neutron production. The observed drive enhancement from rugby geometry in this study is almost twice stronger than in previously published results.

Higher-Order Fermi-Liquid Corrections for an Anderson Impurity Away from Half Filling

NASA Astrophysics Data System (ADS)

Oguri, Akira; Hewson, A. C.

2018-03-01

We study the higher-order Fermi-liquid relations of Kondo systems for arbitrary impurity-electron fillings, extending the many-body quantum theoretical approach of Yamada and Yosida. It includes, partly, a microscopic clarification of the related achievements based on Nozières' phenomenological description: Filippone, Moca, von Delft, and Mora [Phys. Rev. B 95, 165404 (2017), 10.1103/PhysRevB.95.165404]. In our formulation, the Fermi-liquid parameters such as the quasiparticle energy, damping, and transport coefficients are related to each other through the total vertex Γσ σ';σ'σ(ω ,ω';ω',ω ), which may be regarded as a generalized Landau quasiparticle interaction. We obtain exactly this function up to linear order with respect to the frequencies ω and ω' using the antisymmetry and analytic properties. The coefficients acquire additional contributions of three-body fluctuations away from half filling through the nonlinear susceptibilities. We also apply the formulation to nonequilibrium transport through a quantum dot, and clarify how the zero-bias peak evolves in a magnetic field.

Higher-Order Fermi-Liquid Corrections for an Anderson Impurity Away from Half Filling.

PubMed

Oguri, Akira; Hewson, A C

2018-03-23

We study the higher-order Fermi-liquid relations of Kondo systems for arbitrary impurity-electron fillings, extending the many-body quantum theoretical approach of Yamada and Yosida. It includes, partly, a microscopic clarification of the related achievements based on Nozières' phenomenological description: Filippone, Moca, von Delft, and Mora [Phys. Rev. B 95, 165404 (2017)PRBMDO2469-995010.1103/PhysRevB.95.165404]. In our formulation, the Fermi-liquid parameters such as the quasiparticle energy, damping, and transport coefficients are related to each other through the total vertex Γ_{σσ^{'};σ^{'}σ}(ω,ω^{'};ω^{'},ω), which may be regarded as a generalized Landau quasiparticle interaction. We obtain exactly this function up to linear order with respect to the frequencies ω and ω^{'} using the antisymmetry and analytic properties. The coefficients acquire additional contributions of three-body fluctuations away from half filling through the nonlinear susceptibilities. We also apply the formulation to nonequilibrium transport through a quantum dot, and clarify how the zero-bias peak evolves in a magnetic field.

Opioid Analgesic and Benzodiazepine Prescribing Among Medicaid-Enrollees with Opioid Use Disorders: The Influence of Provider Communities

PubMed Central

Stein, Bradley D.; Mendelsohn, Joshua; Gordon, Adam J.; Dick, Andrew W.; Burns, Rachel M.; Sorbero, Mark; Shih, Regina A.; Pacula, Rosalie Liccardo

2017-01-01

Background Opioid analgesic and benzodiazepine use in individuals with opioid use disorders (OUDs) can increase the risk for medical consequences and relapse. Little is known about rates of use of these medications or prescribing patterns among communities of prescribers. Aims To examine rates of prescribing to Medicaid-enrollees in the calendar year after an OUD diagnosis, and to examine individual, county, and provider community factors associated with such prescribing. Methods We used 2008 Medicaid claims data from 12 states to identify enrollees diagnosed with OUDs, and 2009 claims data to identify rates of prescribing of each drug. We used social network analysis to identify provider communities and multivariate regression analyses to identify patient, county, and provider community level factors associated with prescribing these drugs. We also examined variation in rates of prescribing across provider communities. Results Among Medicaid-enrollees identified with an OUD, 45% filled a prescription for an opioid analgesic, 37% for a benzodiazepine, and 21% for both in the year following their diagnosis. Females, older individuals, individuals with pain syndromes, and individuals residing in counties with higher rates of poverty were more likely to fill prescriptions. Prescribing rates varied substantially across provider communities, with rates in the highest quartile of prescribing communities over 2.5 times the rates in the lowest prescribing communities. Discussion Prescribing opioid analgesics and benzodiazepines to individuals diagnosed with OUDs may increase risk of relapse and overdose. Interventions should be considered that target provider communities with the highest rates of prescribing and individuals at highest risk. PMID:27449904

Structure and Filling Characteristics of Paleokarst Reservoirs in the Northern Tarim Basin, Revealed by Outcrop, Core and Borehole Images

NASA Astrophysics Data System (ADS)

Tian, Fei; Lu, Xinbian; Zheng, Songqing; Zhang, Hongfang; Rong, Yuanshuai; Yang, Debin; Liu, Naigui

2017-06-01

The Ordovician paleokarst reservoirs in the Tahe oilfield, with burial depths of over 5300 m, experienced multiple phases of geologic processes and exhibit strong heterogeneity. Core testing can be used to analyse the characteristics of typical points at the centimetre scale, and seismic datasets can reveal the macroscopic outlines of reservoirs at the >10-m scale. However, neither method can identify caves, cave fills and fractures at the meter scale. Guided by outcrop investigations and calibrations based on core sample observations, this paper describes the interpretation of high longitudinal resolution borehole images, the identification of the characteristics of caves, cave fills (sedimentary, breccia and chemical fills) and fractures in single wells, and the identification of structures and fill characteristics at the meter scale in the strongly heterogeneous paleokarst reservoirs. The paleogeomorphology, a major controlling factor in the distribution of paleokarst reservoirs, was also analysed. The results show that one well can penetrate multiple cave layers of various sizes and that the caves are filled with multiple types of fill. The paleogeomorphology can be divided into highlands, slopes and depressions, which controlled the structure and fill characteristics of the paleokarst reservoirs. The results of this study can provide fundamental meter-scale datasets for interpreting detailed geologic features of deeply buried paleocaves, can be used to connect core- and seismic-scale interpretations, and can provide support for the recognition and development of these strongly heterogeneous reservoirs.

Clinical and laboratory evaluation of microstructural changes in the physical, mechanical and chemical properties of dental filling materials under the influence of an electromagnetic field.

PubMed

Moiseeva, Natalia S; Kunin, Anatoly A

2018-03-01

Restorative filling materials used for dental caries prevention and treatment consist of various components including monomers or oligomers, which play a significant role in forming the main structure of these materials, as well as in characterising their physical, mechanical and chemical properties. The necessity for the development and improvement of structural characteristics of polymeric dental filling materials intended for caries prevention and their life duration increase served as the initiating factor of our research. According to the research purpose and challenges, we studied the changes in the physical, mechanical and chemical properties of composite filling materials with and without electromagnetic field influence. The investigations in vivo include the study of microstructural features of polymeric filling materials by scanning electron microscopy (SEM) and the investigations in vitro include the study of sealed and extracted human teeth chips by using X-ray spectral analysis. We also evaluated the changes in the strength characteristics of dental filling materials with and without electromagnetic field influence. The analysis of the obtained data indicates the presence of structural changes in polymeric dental filling materials, including the material microstructure condensation confirmed by the SEM results, an increase in the strength and adhesion characteristics and certain regularities of the chemical elemental composition concentration change in the area of hard tooth tissue and dental filling material. These scientific data will provide tooth caries prevention and promote the increase of treatment quality.

Effect of bulk-fill base material on fracture strength of root-filled teeth restored with laminate resin composite restorations.

PubMed

Taha, N A; Maghaireh, G A; Ghannam, A S; Palamara, J E

2017-08-01

To evaluate the effect of using a bulk-fill flowable base material on fracture strength and fracture patterns of root-filled maxillary premolars with MOD preparations restored with laminate restorations. Fifty extracted maxillary premolars were selected for the study. Standardized MOD cavities with endodontic treatment were prepared for all teeth, except for intact control. The teeth were divided randomly into five groups (n=10); (Group 1) sound teeth, (Group 2) unrestored teeth; (Group 3) MOD cavities with Vitrebond base and resin-based composite (Ceram. X One Universal); (Group 4) MOD cavities with 2mm GIC base (Fuji IX GP) and resin-based composite (Ceram. X One Universal) open laminate, (Group 5) MOD cavities were restored with 4mm of bulk-fill flowable base material (SDR) and resin-based composite (Ceram. X One Universal). All teeth were thermocycled and subjected to a 45° ramped oblique load in a universal testing machine. Fracture load and fracture patterns were recorded. Data were analyzed using one-way ANOVA and Dunnett's T3 test. Restoration in general increased the fracture strength compared to unrestored teeth. The fracture strength of group 5 (bulk-fill) was significantly higher than the fracture strength of the GIC laminate groups and not significantly different from the intact teeth (355±112N, P=0.118). The type of failure was unfavorable for most of the groups, with the majority being mixed failures. The use of a bulk-fill flowable base material significantly increased the fracture strength of extracted root-filled teeth with MOD cavities; however it did not improve fracture patterns to more favorable ones. Investigating restorative techniques that may improve the longevity of root-filled premolar teeth restored with direct resin restorations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Factors Influencing Career Choice among Police Recruits

ERIC Educational Resources Information Center

Cole, Bryan

2012-01-01

This quantitative, non-experimental study examined the career choice factors of 154 (n = 154) police recruits to determine a correlation of age group generation to the five career choice factors presented in the Sibson Reward of Work Model. Law enforcement agencies faced a shortage of viable candidates to fill vacant positions. While extensive…

An Investigation of Relationships between Internal and External Factors Affecting Technology Integration in Classrooms

ERIC Educational Resources Information Center

Hur, Jung Won; Shannon, David; Wolf, Sara

2016-01-01

Various factors affecting technology integration have been identified, but little research has examined the relationships between factors, especially internal and external ones, and whether they directly or indirectly influenced each other. To fill this research gap, this study examined the significance and relationships of five factors…

The Role of Higher Education in the 21st Century: Collaborator or Counterweight?

ERIC Educational Resources Information Center

Castagnera, James Ottavio

2001-01-01

Suggests that higher education should fill the vacuum left by big labor. Asserts that to do this, higher education must become adept at shifting from the right foot of collaboration with big business and big government to the left foot of confrontation, even at the price of lost corporate or government support, when the issue is academic freedom…

Measurement of factors that negatively influence the outcome of quitting smoking among patients with COPD: psychometric analyses of the Try To Quit Smoking instrument.

PubMed

Lundh, Lena; Alinaghizadeh, Hassan; Törnkvist, Lena; Gilljam, Hans; Galanti, Maria Rosaria

2014-12-01

To test internal consistency and factor structure of a brief instrument called Trying to Quit smoking. The most effective treatment for patients with chronic obstructive pulmonary disease is to quit smoking. Constant thoughts about quitting and repeated quit attempts can generate destructive feelings and make it more difficult to quit. Development and psychometric testing of the Trying to Quit smoking scale. The Trying to Quit smoking, an instrument designed to assess pressure-filled states of mind and corresponding pressure-relief strategies, was tested among 63 Swedish patients with chronic obstructive pulmonary disease. Among these, the psychometric properties of the instrument were analysed by Exploratory Factor Analyses. Fourteen items were included in the factor analyses, loading on three factors labelled: (1) development of pressure-filled mental states; (2) use of destructive pressure-relief strategies; and (3) ambivalent thoughts when trying to quit smoking. These three factors accounted for more than 80% of the variance, performed well on the Kaiser-Meyer-Olkin (KMO) test and had high internal consistency.

The effect of exchange interaction on quasiparticle Landau levels in narrow-gap quantum well heterostructures.

PubMed

Krishtopenko, S S; Gavrilenko, V I; Goiran, M

2012-04-04

Using the 'screened' Hartree-Fock approximation based on the eight-band k·p Hamiltonian, we have extended our previous work (Krishtopenko et al 2011 J. Phys.: Condens. Matter 23 385601) on exchange enhancement of the g-factor in narrow-gap quantum well heterostructures by calculating the exchange renormalization of quasiparticle energies, the density of states at the Fermi level and the quasiparticle g-factor for different Landau levels overlapping. We demonstrate that exchange interaction yields more pronounced Zeeman splitting of the density of states at the Fermi level and leads to the appearance of peak-shaped features in the dependence of the Landau level energies on the magnetic field at integer filling factors. We also find that the quasiparticle g-factor does not reach the maximum value at odd filling factors in the presence of large overlapping of spin-split Landau levels. We advance an argument that the behavior of the quasiparticle g-factor in weak magnetic fields is defined by a random potential of impurities in narrow-gap heterostructures. © 2012 IOP Publishing Ltd

Finite Element Analysis in Concurrent Processing: Computational Issues

NASA Technical Reports Server (NTRS)

Sobieszczanski-Sobieski, Jaroslaw; Watson, Brian; Vanderplaats, Garrett

2004-01-01

The purpose of this research is to investigate the potential application of new methods for solving large-scale static structural problems on concurrent computers. It is well known that traditional single-processor computational speed will be limited by inherent physical limits. The only path to achieve higher computational speeds lies through concurrent processing. Traditional factorization solution methods for sparse matrices are ill suited for concurrent processing because the null entries get filled, leading to high communication and memory requirements. The research reported herein investigates alternatives to factorization that promise a greater potential to achieve high concurrent computing efficiency. Two methods, and their variants, based on direct energy minimization are studied: a) minimization of the strain energy using the displacement method formulation; b) constrained minimization of the complementary strain energy using the force method formulation. Initial results indicated that in the context of the direct energy minimization the displacement formulation experienced convergence and accuracy difficulties while the force formulation showed promising potential.

Paeoniae alba Radix Promotes Peripheral Nerve Regeneration

PubMed Central

Huang, Kun-Shan; Lin, Jaung-Geng; Lee, Han-Chung; Tsai, Fuu-Jen; Bau, Da-Tian; Huang, Chih-Yang; Yao, Chun-Hsu; Chen, Yueh-Sheng

2011-01-01

The present study provides in vitro and in vivo evaluation of Paeoniae alba Radix (PR) on peripheral nerve regeneration. In the in vitro study, we found the PR caused a marked enhancement of the nerve growth factor-mediated neurite outgrowth from PC12 cells as well as their expression of growth associated protein 43 and synapsin I. In the in vivo study, silicone rubber chambers filled with the PR water extract were used to bridge a 10-mm sciatic nerve defect in rats. At the conclusion of 8 weeks, regenerated nerves in the PR groups, especially at 1.25 mg ml−1 had a higher rate of successful regeneration across the wide gap, relatively larger mean values of total nerve area, myelinated axon count and blood vessel number, and a significantly larger nerve conductive velocity compared to the control group (P  <  .05). These results suggest that the PR extract can be a potential nerve growth-promoting factor, being salutary in aiding the growth of injured peripheral nerve. PMID:19687191

The Strengths and Difficulties Questionnaire: psychometric properties of the parent and teacher version in children aged 4-7.

PubMed

Stone, Lisanne L; Janssens, Jan M A M; Vermulst, Ad A; Van Der Maten, Marloes; Engels, Rutger C M E; Otten, Roy

2015-01-01

The Strengths and Difficulties Questionnaire is one of the most employed screening instruments. Although there is a large research body investigating its psychometric properties, reliability and validity are not yet fully tested using modern techniques. Therefore, we investigate reliability, construct validity, measurement invariance, and predictive validity of the parent and teacher version in children aged 4-7. Besides, we intend to replicate previous studies by investigating test-retest reliability and criterion validity. In a Dutch community sample 2,238 teachers and 1,513 parents filled out questionnaires regarding problem behaviors and parenting, while 1,831 children reported on sociometric measures at T1. These children were followed-up during three consecutive years. Reliability was examined using Cronbach's alpha and McDonald's omega, construct validity was examined by Confirmatory Factor Analysis, and predictive validity was examined by calculating developmental profiles and linking these to measures of inadequate parenting, parenting stress and social preference. Further, mean scores and percentiles were examined in order to establish norms. Omega was consistently higher than alpha regarding reliability. The original five-factor structure was replicated, and measurement invariance was established on a configural level. Further, higher SDQ scores were associated with future indices of higher inadequate parenting, higher parenting stress and lower social preference. Finally, previous results on test-retest reliability and criterion validity were replicated. This study is the first to show SDQ scores are predictively valid, attesting to the feasibility of the SDQ as a screening instrument. Future research into predictive validity of the SDQ is warranted.

Fill-factor improvement of Si CMOS single-photon avalanche diode detector arrays by integration of diffractive microlens arrays.

PubMed

Intermite, Giuseppe; McCarthy, Aongus; Warburton, Ryan E; Ren, Ximing; Villa, Federica; Lussana, Rudi; Waddie, Andrew J; Taghizadeh, Mohammad R; Tosi, Alberto; Zappa, Franco; Buller, Gerald S

2015-12-28

Single-photon avalanche diode (SPAD) detector arrays generally suffer from having a low fill-factor, in which the photo-sensitive area of each pixel is small compared to the overall area of the pixel. This paper describes the integration of different configurations of high efficiency diffractive optical microlens arrays onto a 32 × 32 SPAD array, fabricated using a 0.35 µm CMOS technology process. The characterization of SPAD arrays with integrated microlens arrays is reported over the spectral range of 500-900 nm, and a range of f-numbers from f/2 to f/22. We report an average concentration factor of 15 measured for the entire SPAD array with integrated microlens array. The integrated SPAD and microlens array demonstrated a very high uniformity in overall efficiency.

ESR Detection of optical dynamic nuclear polarization in GaAs/Al{sub x}Ga{sub 1-x}As quantum wells at unity filling factor in the quantum Hall effect

DOE Office of Scientific and Technical Information (OSTI.GOV)

Vitkalov, Sergey A.; Bowers, C. Russell; Simmons, Jerry A.

2000-02-15

This paper presents a study of the enhancement of the Zeeman energy of two-dimensional (2D) conduction electrons near the {nu}=1 filling factor of the quantum Hall effect by optical dynamic nuclear polarization. The change in the Zeeman energy is determined from the Overhauser shift of the transport detected electron spin resonance in GaAs/Al{sub x}Ga{sub 1-x}As multiquantum wells. In a separate experiment the NMR signal enhancement factor is obtained by radio frequency detected nuclear magnetic resonance under similar conditions in the same sample. These measurements afford an estimation of the hyperfine coupling constant between the nuclei and 2D conduction electrons. (c)more » 2000 The American Physical Society.« less

Impact of asthma controller medications on medical and economic resource utilization in adult asthma patients.

PubMed

Lee, Todd A; Chang, Chun-Lan; Stephenson, Judith J; Sajjan, Shiva G; Maiese, Eric M; Everett, Sharlette; Allen-Ramey, Felicia

2010-12-01

To compare asthma-related resource utilization, adherence and costs among adults prescribed asthma controller regimens. Medical and pharmacy claims from a US managed-care claims database were used to identify adults (18-56 years) initiating asthma controller therapy. Patients had 2 years continuous enrollment and ≥ 1 medical claims for asthma (ICD9: 493.xx) (January 2004 - March 2009). Asthma exacerbations, short-acting β-agonist (SABA) fills, adherence (MPR ≥ 0.80) and asthma-related costs were assessed for 1 year after the initial asthma controller medication claim. Separate logistic and negative binomial regression models for monotherapy and combination therapy were developed to examine the impact of controller therapy on outcomes. A total of 28 074 patients [inhaled corticosteroids (ICS) (26.3%), leukotriene modifiers (LM) (23.2%), ICS  +  long acting β-agonist (LABA) (48.5%), ICS + LM (2%)] were included. LM patients had lower odds of ≥ 6 SABA fills (OR(adj) = 0.83, 95% CI: 0.73-0.96) and lower rates of asthma exacerbations (RR(adj) = 0.82, 0.75-0.89) vs. ICS patients. Odds of ≥ 6 SABA fills were similar for ICS + LM vs. ICS + LABA (OR(adj) = 1.3, 0.96-1.76); the rate of asthma exacerbations was greater for ICS + LM compared with ICS + LABA (OR(adj) = 1.4, 1.2-1.6). The proportion adherent was greatest for LM (14.9%) and ICS + LABA (4.1%). LM patients had higher unadjusted pharmacy costs, but lower medical costs compared to ICS patients. For combination therapy, ICS + LM had higher unadjusted mean medical and pharmacy costs vs. ICS + LABA. Higher adjusted mean total costs in the post-index period were observed for LM vs. ICS patients ($837 vs. 684) and for ICS + LM vs. ICS + LABA patients ($1223 vs. 873). LM monotherapy was associated with lower medical costs but higher total costs resulting from greater treatment adherence. Conversely, higher costs for ICS + LM resulted from greater exacerbations compared to ICS + LABA despite similar adherence. Higher total costs with LM were due to drug costs. Precise utilization of the medications filled by patients could not be determined.

Staggered Orbital Currents in the Half-Filled Two-Leg Ladder

NASA Astrophysics Data System (ADS)

Fjaerestad, J. O.; Marston, Brad; Sudbo, A.

2002-03-01

We present strong analytical and numerical evidence for the existence of a staggered flux (SF) phase in the half-filled two-leg ladder, with true long-range order in the counter-circulating currents. Using abelian bosonization with a careful treatment of the Klein factors, we show that a certain phase of the half-filled ladder, previously identified as having spin-Peierls order, instead exhibits staggered orbital currents with no dimerization.(J. O. Fjærestad and J. B. Marston, cond- mat/0107094.) This result, combined with a weak-coupling renormalization-group analysis, implies that the SF phase exists in a region of the phase diagram of the half-filled t-U-V-J ladder. Using the density-matrix renormalization-group (DMRG) approach generalized to complex-valued wavefunctions, we demonstrate that the SF phase exhibits robust currents at intermediate values of the interaction strengths.

Efficacy of ultrasonic activation of NaOCl and orange oil in removing filling material from mesial canals of mandibular molars with and without isthmus

PubMed Central

Barreto, Mirela Sangoi; da Rosa, Ricardo Abreu; Santini, Manuela Favarin; Cavenago, Bruno Cavalini; Duarte, Marco Antônio Húngaro; Bier, Carlos Alexandre Souza; Só, Marcos Vinícius Reis

2016-01-01

ABSTRACT Objectives The aim of this study was to evaluate the volume of remaining filling material after passive ultrasonic irrigation (PUI) of sodium hypochlorite (NaOCl) and orange oil in mesial canals of mandibular molars, with and without isthmus. Material and Methods Thirty mesial roots of mandibular molars were divided according to the presence or absence of isthmus. Canals were prepared and filled (Micro-CT #1). Filling was removed using rotary instruments, and specimens were sub-divided into three groups according to the irrigation procedures: Conventional – conventional irrigation with NaOCl, PUI/NaOCl – PUI of NaOCl (three activations, 20 seconds each), and PUI/orange oil – PUI of orange oil (Micro-CT#2). Specimens were enlarged using the X2 and X3 ProTaper Next instruments and submitted to the same irrigation protocols (Micro-CT #3). Results No differences were found between the experimental groups in each stage of assessment (P>0.05). The volume of residual filling material was similar to those in Micro-CT #2 and Micro-CT #3, but lower than those observed in Micro-CT #1 (P<0.05). When groups were pooled according to the presence or absence of an isthmus, volume of residual filling material was higher in specimens presenting isthmus (P<0.05). Conclusions PUI of NaOCl or orange oil did not improve filling removal. Isthmus consists in an anatomical obstacle that impairs the removal of filling material. PMID:26200525

Carpel size, grain filling, and morphology determine individual grain weight in wheat

PubMed Central

Xie, Quan; Mayes, Sean; Sparkes, Debbie L.

2015-01-01

Individual grain weight is a major yield component in wheat. To provide a comprehensive understanding of grain weight determination, the carpel size at anthesis, grain dry matter accumulation, grain water uptake and loss, grain morphological expansion, and final grain weight at different positions within spikelets were investigated in a recombinant inbred line mapping population of bread wheat (Triticum aestivum L.)×spelt (Triticum spelta L.). Carpel size, grain dry matter and water accumulation, and grain dimensions interacted strongly with each other. Furthermore, larger carpels, a faster grain filling rate, earlier and longer grain filling, more grain water, faster grain water absorption and loss rates, and larger grain dimensions were associated with higher grain weight. Frequent quantitative trait locus (QTL) coincidences between these traits were observed, particularly those on chromosomes 2A, 3B, 4A, 5A, 5DL, and 7B, each of which harboured 16−49 QTLs associated with >12 traits. Analysis of the allelic effects of coincident QTLs confirmed their physiological relationships, indicating that the complex but orderly grain filling processes result mainly from pleiotropy or the tight linkages of functionally related genes. After grain filling, distal grains within spikelets were smaller than basal grains, primarily due to later grain filling and a slower initial grain filling rate, followed by synchronous maturation among different grains. Distal grain weight was improved by increased assimilate availability from anthesis. These findings provide deeper insight into grain weight determination in wheat, and the high level of QTL coincidences allows simultaneous improvement of multiple grain filling traits in breeding. PMID:26246614

Effects of annulus defects and implantation of poly(lactic-co-glycolic acid) (PLGA)/fibrin gel scaffolds on nerves ingrowth in a rabbit model of annular injury disc degeneration.

PubMed

Xin, Long; Xu, Weixing; Yu, Leijun; Fan, Shunwu; Wang, Wei; Yu, Fang; Wang, Zhenbin

2017-05-12

Growth of nerve fibers has been shown to occur in a rabbit model of intravertebral disc degeneration (IVD) induced by needle puncture. As nerve growth may underlie the process of chronic pain in humans affected by disc degeneration, we sought to investigate the factors underlying nerve ingrowth in a minimally invasive annulotomy rabbit model of IVD by comparing the effects of empty disc defects with those of defects filled with poly(lactic-co-glycolic acid)/fibrin gel (PLGA) plugs. New Zealand white rabbits (n = 24) received annular injuries at three lumbar levels (L3/4, L4/5, and L5/6). The discs were randomly assigned to four groups: (a) annular defect (1.8-mm diameter; 4-mm depth) by mini-trephine, (b) annular defect implanted with a PLGA scaffold containing a fibrin gel, (c) annular puncture by a 16G needle (5-mm depth), and (d) uninjured L2/3 disc (control). Disc degeneration was evaluated by radiography, MRI, histology, real-time PCR, and analysis of proteoglycan (PG) content. Nerve ingrowth into the discs was assessed by immunostaining with the nerve marker protein gene product 9.5. Injured discs showed a progressive disc space narrowing with significant disc degeneration and proteoglycan loss, as confirmed by imaging results, molecular and compositional analysis, and histological examinations. In 16G punctured discs, nerve ingrowth was observed on the surface of scar tissue. In annular defects, nerve fibers were found to be distributed along small fissures within the fibrocartilaginous-like tissue that filled the AF. In discs filled with PLGA/ fibrin gel, more nerve fibers were observed growing deeper into the inner AF along the open annular track.  In addition, innervations scores showed significantly higher than those of punctured discs and empty defects. A limited vascular proliferation was found in the injured sites and regenerated tissues. Nerve ingrowth was significantly higher in PLGA/fibrin-filled discs than in empty defects. Possible explanations include (i) annular fissures along the defect and early loss of proteoglycan may facilitate the ingrowth process and (ii) biodegradable PLGA/fibrin gel may promote adverse growth of nerves and blood vessels into deeper parts of injured disc. The rabbit annular defect model of disc degeneration appears suitable to investigate the effects of nerve ingrowth in relation to pain generation.

The Influence of the Orbera Intragastric Balloon Filling Volumes on Weight Loss, Tolerability, and Adverse Events: a Systematic Review and Meta-Analysis.

PubMed

Kumar, Nitin; Bazerbachi, Fateh; Rustagi, Tarun; McCarty, Thomas R; Thompson, Christopher C; Galvao Neto, Manoel P; Zundel, Natan; Wilson, Erik B; Gostout, Christopher J; Abu Dayyeh, Barham K

2017-09-01

The Orbera intragastric balloon (IGB) has been approved by the US Food and Drug Administration for use in patients with a body mass index (BMI) between 30 and 40 kg/m 2 and is in wide use worldwide as a primary and bridge obesity management tool. The balloon filling volume (BFV) ranges between 400 and 700 mL of saline. Our objective was to determine whether there is an association between BFV and clinically relevant endpoints, namely weight loss outcomes, balloon tolerability, and adverse events. A systematic review of studies investigating the use of the Orbera IGB system for obesity treatment was performed. Data was examined using random effects modelling and meta-regression analyses. Forty-four studies (n = 5549 patients) reported BFV and % total body weight loss (TBWL) at 6 months. Pooled %TBWL at 6 months was 13.2% [95% CI 12.3-14.0]. A funnel plot demonstrated a low risk of publication bias. Meta-regression showed no statistically significant association between filling volume and %TBWL at 6 months (p = 0.268). Higher BFV was associated with lower rates of esophagitis (slope = -0.008, p < 0.001) and prosthesis migration (slope = -0.015, p < 0.001). There was no association between BFV and early removal (p = 0.1), gastroesophageal reflux symptom (p = 0.64), or ulcer rates (p = 0.09). No association was observed between Orbera IGB filling volume and weight loss outcomes. Higher volumes appear to be associated with lower migration and esophagitis rates; thus, a balloon filling volume of 600-650 mL is recommended.

Tissue reactions to a new mineral trioxide aggregate-containing endodontic sealer.

PubMed

Tavares, Cauana Oliva; Böttcher, Daiana Elisabeth; Assmann, Eloísa; Kopper, Patrícia Maria Poli; de Figueiredo, José Antônio Poli; Grecca, Fabiana Soares; Scarparo, Roberta Kochenborger

2013-05-01

The purpose of this study was to analyze the connective tissue reactions to MTA Fillapex (Ângelus Indústria de Produtos Odontlógicos Ltda, Londrina, Brazil) compared with a zinc oxide-based sealer (EndoFill; Dentsply Indústria e Comérico Ltda, Petrópolis, Brazil) and an epoxy resin-based material (AH Plus; Dentsply DeTrey GmbH, Konstanz, Germany) in Wistar rats. Polyethylene tubes containing the test materials and empty polyethylene tubes (control) were implanted in the subcutaneous tissue of 12 rats. Empty tubes were used as a negative control. After 7 and 60 days (n = 6 per period), observations were made for cellular inflammatory components, fibrous condensation, and abscess formation. Comparisons among the groups and between the experimental periods were made using 2-way analysis of variance and the Bonferroni post hoc test (P < .05). At the end of the 7-day experimental period, all sealers scored higher than the control group for the variable lymphocytes, and MTA Fillapex presented lower fiber condensation compared with empty tubes. After 60 days, macrophages and lymphocytes scored significantly higher for MTA Fillapex and EndoFill compared with the negative control, and AH Plus showed similar results related to the empty tubes. Comparing the materials' responses at the end of the 2 evaluated periods, for EndoFill samples the variable neutrophils was detected less after 60 days. Both EndoFill and MTA Fillapex presented increased fiber condensation after 60 days. Although none of the sealers promoted ideal tissue responses, AH Plus presented the best outcomes. Although MTA Fillapex contains MTA powder, it presented no biocompatibility advantages when compared with AH Plus and EndoFill. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Resistance to vertical fracture of MTA-filled roots.

PubMed

EL-Ma'aita, Ahmad M; Qualtrough, Alison J E; Watts, David C

2014-02-01

To investigate the effect of MTA root canal fillings on the resistance to vertical root fracture (VRF) over different time intervals. Freshly extracted anterior human teeth with single canals and minimal curvatures were decoronated, instrumented to size 50/.05 ProTaper file, irrigated with 1%NaOCl and randomly allocated to one of three groups (n = 36): (i) filled with MTA, (ii) filled with gutta-percha and sealer and (iii) unfilled roots used as a negative control. Each group was subdivided into three subgroups (n = 12) according to the storage time of 48 h, 1 and 6 months at 37°C in synthetic tissue fluid (STF). Following the storage periods, filled roots were mounted in acrylic supports, and the periodontal ligament was simulated using elastomeric impression material. Vertical loading was carried out with a ball-ended steel cylinder fitted on a universal testing machine at 1 mm/min crosshead speed. The maximum force at fracture (F-max) and the fracture mode were recorded for each root. Data were statistically analysed using two-way anova and Bonferroni post hoc tests. The mean F-max was significantly higher in the MTA subgroups after 1 and 6 months compared with all other subgroups. Two modes of fracture were identified: split and comminuted. The mean F-max values recorded with the latter were significantly higher compared with the former (P < 0.001). In all groups, split fracture was the most dominant mode apart from the MTA/1 month and MTA/6 month groups. MTA increases the resistance to VRF of endodontically treated teeth and influences the mode of fracture after 1 and 6 month of storage in STF compared with gutta-percha and sealer. © 2013 John Wiley & Sons A/S.

Optimization of Squeeze Casting for Aluminum Alloy Parts

DOE Office of Scientific and Technical Information (OSTI.GOV)

David Schwam; John F. Wallace; Qingming Chang

2002-07-30

This study was initiated with the installation of a new production size UBE 350 Ton VSC Squeeze Casting system in the Metal Casting Laboratory at Case Western University. A Lindberg 75k W electrical melting furnace was installed alongside. The challenge of installation and operation of such industrial-size equipment in an academic environment was met successfully. Subsequently, a Sterling oil die heater and a Visi-Track shot monitoring system were added. A significant number of inserts were designed and fabricated over the span of the project, primarily for squeeze casting different configurations of test bars and plates. A spiral ''ribbon insert'' formore » evaluation of molten metal fluidity was also fabricated. These inserts were used to generate a broad range of processing conditions and determine their effect on the quality of the squeeze cast parts. This investigation has studied the influence of the various casting variables on the quality of indirect squeeze castings primarily of aluminum alloys. The variables studied include gating design, fill time and fill patter, metal pressure and die temperature variations. The quality of the die casting was assessed by an analysis of both their surface condition and internal soundness. The primary metal tested was an aluminum 356 alloy. In addition to determining the effect of these casting variables on casting quality as measured by a flat plate die of various thickness, a number of test bar inserts with different gating designs have been inserted in the squeeze casting machine. The mechanical properties of these test bars produced under different squeeze casting conditions were measured and reported. The investigation of the resulting properties also included an analysis of the microstructure of the squeeze castings and the effect of the various structural constituents on the resulting properties. The main conclusions from this investigation are as follows: The ingate size and shape are very important since it must remain open until the casting is solidified and pressure is maintained on the solidifying casting. Fanned gates, particularly on the smaller section castings avoid jetting effects at the ingate end. The fan type ingate helps accomplish a rapid fill without high velocities. The molten metal has to fill the cavity before localized solidification occurs. This is best accomplished with a larger ingate to attain rapid filling without excessive velocity or jetting that occurs at high metal velocities. Straight gates are prone to case jetting of the metal stream even a low velocities. Fanned gates allow use of higher fill velocity without excessive jetting. A higher metal pressure provides a more complete fill of the die including improved compensation for solidification shrinkage. With the proper filling pattern, ingates, overflows and die temperature for a given die, very good tensile properties can be attained in squeeze casting. In general, the smaller squeeze castings require higher die temperatures. Computer models using the UES Procast and MagmaSoft finite element software can, after suitable adjustments, predict the flow pattern in the die cavity.« less

Experimental comparison of forces resisting viral DNA packaging and driving DNA ejection

PubMed Central

Keller, Nicholas; Berndsen, Zachary T.; Jardine, Paul J.; Smith, Douglas E.

2018-01-01

We compare forces resisting DNA packaging in bacteriophage phi29 inferred from optical tweezers studies with forces driving DNA ejection inferred from osmotic pressure studies. Ejection forces from 0–80% filling are consistent with a model that assumes a repulsive DNA-DNA interaction potential derived from DNA condensation studies and predicts an inverse spool DNA conformation. Forces resisting packaging from ~80–100% filling are also consistent with this model. However, that electron microscopy does not reveal a spool conformation suggests that this model overestimates bending rigidity and underestimates repulsion. Below 80% filling, inferred ejection forces are higher than those resisting packaging. Although unexpected, this suggests that most force that builds during packaging is available to drive DNA ejection. PMID:28618627

Preparation and Dielectric Properties of SiC/LSR Nanocomposites for Insulation of High Voltage Direct Current Cable Accessories

PubMed Central

Shang, Nanqiang; Chen, Qingguo; Wei, Xinzhe

2018-01-01

The conductivity mismatch in the composite insulation of high voltage direct current (HVDC) cable accessories causes electric field distribution distortion and even insulation breakdown. Therefore, a liquid silicone rubber (LSR) filled with SiC nanoparticles is prepared for the insulation of cable accessories. The micro-morphology of the SiC/LSR nanocomposites is observed by scanning electron microscopy, and their trap parameters are characterized using thermal stimulated current (TSC) tests. Moreover, the dielectric properties of SiC/LSR nanocomposites with different SiC concentrations are tested. The results show that the 3 wt % SiC/LSR sample has the best nonlinear conductivity, more than one order of magnitude higher than that of pure LSR with improved temperature and nonlinear conductivity coefficients. The relative permittivity increased 0.2 and dielectric loss factor increased 0.003, while its breakdown strength decreased 5 kV/mm compared to those of pure LSR. Moreover, the TSC results indicate the introduction of SiC nanoparticles reduced the trap level and trap density. Furthermore, the SiC nanoparticles filling significantly increased the sensitivity of LSR to electric field stress and temperature changes, enhancing the conductivity and electric field distribution within the HVDC cable accessories, thus improving the reliability of the HVDC cable accessories. PMID:29518054

[The quality of professional life and the pride in working in public health. The results of a survey].

PubMed

Clúa Espuny, J L; Aguilar Martín, C

1998-09-30

To find what factors explain best the pride of belonging to a public health enterprise. A descriptive crossover study. One primary care CHS. Staff of 363 from Tortosa's Primary Care administrative staff. All the employees were sent a self-filling questionnaire on the quality of their professional life. 232 returned the questionnaire filled in (63.9%). They showed an average value for the overall quality of professional life (5.40 +/- 2.09). The general profile covered the following perceptions taken together: sufficient intrinsic motivation; in a work-place with sufficient responsibility, training and social support; associated with enough work-load; with some emotional support from the managers; having some inconveniences caused by work. The pride in belonging to the CHS was high (6.86 +/- 2.50), with those over 45 giving a significantly higher average reply. Among doctors, pride was significantly lower. The multiple regression model identified three significant variables which explained 67.5% of the variability in the pride of belonging to the CHS: recognition of effort, being properly trained for their current job and length of service. a) Professionals are quite proud of belonging to the CHS. b) Their perception of the quality of professional life is average.

Ground-state phase diagram of the repulsive fermionic t -t' Hubbard model on the square lattice from weak coupling

NASA Astrophysics Data System (ADS)

Šimkovic, Fedor; Liu, Xuan-Wen; Deng, Youjin; Kozik, Evgeny

2016-08-01

We obtain a complete and numerically exact in the weak-coupling limit (U →0 ) ground-state phase diagram of the repulsive fermionic Hubbard model on the square lattice for filling factors 0

Euthanasia attitude; A comparison of two scales

PubMed Central

Aghababaei, Naser; Farahani, Hojjatollah; Hatami, Javad

2011-01-01

The main purposes of the present study were to see how the term “euthanasia” influences people’s support for or opposition to euthanasia; and to see how euthanasia attitude relates to religious orientation and personality factors. In this study two different euthanasia attitude scales were compared. 197 students were selected to fill out either the Euthanasia Attitude Scale (EAS) or Wasserman’s Attitude Towards Euthanasia scale (ATE scale). The former scale includes the term “euthanasia”, the latter does not. All participants filled out 50 items of International Personality Item Pool, 16 items of the the HEXACO openness, and 14 items of Religious Orientation Scale-Revised. Results indicated that even though the two groups were not different in terms of gender, age, education, religiosity and personality, mean score on the ATE scale was significantly higher than that of the EAS. Euthanasia attitude was negatively correlated with religiosity and conscientiousness and it was positively correlated with psychoticism and openness. It can be concluded that analyzing the attitude towards euthanasia with the use of EAS rather than the ATE scale results in lower levels of opposition against euthanasia. This study raises the question of whether euthanasia attitude scales should contain definitions and concepts of euthanasia or they should describe cases of it. PMID:23908751

Efficiency of light curing units in a government dental school.

PubMed

Nassar, Hani M; Ajaj, Reem; Hasanain, Fatin

2018-01-01

The light intensity of a light-curing unit is a crucial factor that affects the clinical longevity of resin composites. This study aimed to investigate the efficiency of light-curing units in use at a local governmental dental school for curing conventional and bulk-fill resin materials. A total of 166 light-curing units at three locations were examined, and the brand, type, clinic location, diameter of curing tip, tip cleanliness (using a visual score), and the output (in mW/cm 2 using a digital radiometer) were recorded. Only 23.5% of the units examined had clean tips, with the graduate student clinical area containing the highest percentage of clean tips. Further, tips with poor cleanliness score values were associated with significantly lower output intensities. A small percentage (9.4%) of units was capable of producing intensities higher than 1,200 mW/cm 2 and lower than 600 mW/cm 2 (7.6%). The majority of the low intensity units were located in the undergraduate student area, which also contained the highest number of units with intensities between 900 and 1,200 mW/cm 2 . The output of all the units in service was satisfactory for curing conventional resin composites, and most units were capable of curing bulk-fill resin materials.

Preparation and Dielectric Properties of SiC/LSR Nanocomposites for Insulation of High Voltage Direct Current Cable Accessories.

PubMed

Shang, Nanqiang; Chen, Qingguo; Wei, Xinzhe

2018-03-08

The conductivity mismatch in the composite insulation of high voltage direct current (HVDC) cable accessories causes electric field distribution distortion and even insulation breakdown. Therefore, a liquid silicone rubber (LSR) filled with SiC nanoparticles is prepared for the insulation of cable accessories. The micro-morphology of the SiC/LSR nanocomposites is observed by scanning electron microscopy, and their trap parameters are characterized using thermal stimulated current (TSC) tests. Moreover, the dielectric properties of SiC/LSR nanocomposites with different SiC concentrations are tested. The results show that the 3 wt % SiC/LSR sample has the best nonlinear conductivity, more than one order of magnitude higher than that of pure LSR with improved temperature and nonlinear conductivity coefficients. The relative permittivity increased 0.2 and dielectric loss factor increased 0.003, while its breakdown strength decreased 5 kV/mm compared to those of pure LSR. Moreover, the TSC results indicate the introduction of SiC nanoparticles reduced the trap level and trap density. Furthermore, the SiC nanoparticles filling significantly increased the sensitivity of LSR to electric field stress and temperature changes, enhancing the conductivity and electric field distribution within the HVDC cable accessories, thus improving the reliability of the HVDC cable accessories.

Psychopharmacologic Services for Homeless Veterans: Comparing Psychotropic Prescription Fills Among Homeless and Non-Homeless Veterans with Serious Mental Illness.

PubMed

Hermes, Eric; Rosenheck, Robert

2016-02-01

Using national Veterans Health Administration (VHA) administrative data, this study evaluated differences in psychotropic medication use between homeless and non-homeless adults with serious mental illness (SMI) who used VHA services in 2010. The adjusted mean number of psychotropic prescription fills associated with homeless individuals were identified using regression models adjusted for socio-demographics, diagnoses, and use of health services. Of the 876,989 individuals with SMI using VHA services, 7.2 % were homeless at some time during 2010. In bivariate analysis, homeless individuals filled more psychotropic medication prescriptions compared with non-homeless individuals. However, after adjusting for potentially confounding variables, homeless individuals were found to have filled 16.2 % fewer prescriptions than non-homeless individuals when all psychotropics were analyzed together (F = 6947.1, p < .001) and for most individual classes of psychotropics. Greater use of residential/inpatient mental health services by the homeless was the most important single factor associated with filling more psychotropic prescriptions than non-homeless individuals.

Gating geometry studies of thin-walled 17-4PH investment castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maguire, M.C.; Zanner, F.J.

1992-11-01

The ability to design gating systems that reliably feed and support investment castings is often the result of ``cut-and-try`` methodology. Factors such as hot tearing, porosity, cold shuts, misruns, and shrink are defects often corrected by several empirical gating design iterations. Sandia National Laboratories is developing rules that aid in removing the uncertainty involved in the design of gating systems for investment castings. In this work, gating geometries used for filling of thin walled investment cast 17-4PH stainless steel flat plates were investigated. A full factorial experiment evaluating the influence of metal pour temperature, mold preheat temperature, and mold channelmore » thickness were conducted for orientations that filled a horizontal flat plate from the edge. A single wedge gate geometry was used for the edge-gated configuration. Thermocouples placed along the top of the mold recorded metal front temperatures, and a real-time x-ray imaging system tracked the fluid flow behavior during filling of the casting. Data from these experiments were used to determine the terminal fill volumes and terminal fill times for each gate design.« less

Gating geometry studies of thin-walled 17-4PH investment castings

DOE Office of Scientific and Technical Information (OSTI.GOV)

Maguire, M.C.; Zanner, F.J.

1992-01-01

The ability to design gating systems that reliably feed and support investment castings is often the result of cut-and-try'' methodology. Factors such as hot tearing, porosity, cold shuts, misruns, and shrink are defects often corrected by several empirical gating design iterations. Sandia National Laboratories is developing rules that aid in removing the uncertainty involved in the design of gating systems for investment castings. In this work, gating geometries used for filling of thin walled investment cast 17-4PH stainless steel flat plates were investigated. A full factorial experiment evaluating the influence of metal pour temperature, mold preheat temperature, and mold channelmore » thickness were conducted for orientations that filled a horizontal flat plate from the edge. A single wedge gate geometry was used for the edge-gated configuration. Thermocouples placed along the top of the mold recorded metal front temperatures, and a real-time x-ray imaging system tracked the fluid flow behavior during filling of the casting. Data from these experiments were used to determine the terminal fill volumes and terminal fill times for each gate design.« less

Dielectric Characteristics of Oil filled Transformer under Non-standard Lightning Surge Waveforms

NASA Astrophysics Data System (ADS)

Okabe, Shigemitsu; Kawashima, Takeshi; Inoue, Tamotsu; Teranishi, Tsuneharu; Nagaoka, Satoshi

To achieve a rational insulation design for transformers, it is important to evaluate dielectric strength against actually impinging on equipment on-site This paper deals with the dielectric characteristics of a turn-to-turn insulation model for oil filled transformer under non-standard lightning surge waveforms combined with oscillatory voltage. As the results‚ the breakdown voltages and the partial discharge inception voltages of a turn-to-turn insulation model under non-standard impulse wave forms are higher than standard impulse voltages.

Broadband perfect infrared absorption by tuning epsilon-near-zero and epsilon-near-pole resonances of multilayer ITO nanowires.

PubMed

Zhou, Kun; Cheng, Qiang; Song, Jinlin; Lu, Lu; Jia, Zhihao; Li, Junwei

2018-01-01

We numerically investigate the broadband perfect infrared absorption by tuning epsilon-near-zero (ENZ) and epsilon-near-pole (ENP) resonances of multilayer indium tin oxide nanowires (ITO NWs). The monolayer ITO NWs array shows intensive absorption at ENZ and ENP wavelengths for p polarization, while only at the ENP wavelength for s polarization. Moreover, the ENP resonances are almost omnidirectional and the ENZ resonances are angularly dependent. Therefore, the absorption bandwidth is broader for p polarization than that for s polarization when polarized waves are incident obliquely. The ENZ resonances can be tuned by altering the doping concentration and volume filling factor of ITO NWs. However, the ENP resonances only can be tuned by changing the doping concentration of ITO NWs, and volume filling factor impacts little on the ENP resonances. Based on the strong absorption properties of each layer at their own ENP and ENZ resonances, the tuned absorption of the bilayer ITO NWs with the different doping concentrations can be broader and stronger. Furthermore, multilayer ITO NWs can achieve broadband perfect absorption by controlling the doping concentration, volume filling factor, and length of the NWs in each layer. This study has the potential to apply to applications requiring efficient absorption and energy conversion.

Photodiode area effect on performance of X-ray CMOS active pixel sensors

NASA Astrophysics Data System (ADS)

Kim, M. S.; Kim, Y.; Kim, G.; Lim, K. T.; Cho, G.; Kim, D.

2018-02-01

Compared to conventional TFT-based X-ray imaging devices, CMOS-based X-ray imaging sensors are considered next generation because they can be manufactured in very small pixel pitches and can acquire high-speed images. In addition, CMOS-based sensors have the advantage of integration of various functional circuits within the sensor. The image quality can also be improved by the high fill-factor in large pixels. If the size of the subject is small, the size of the pixel must be reduced as a consequence. In addition, the fill factor must be reduced to aggregate various functional circuits within the pixel. In this study, 3T-APS (active pixel sensor) with photodiodes of four different sizes were fabricated and evaluated. It is well known that a larger photodiode leads to improved overall performance. Nonetheless, if the size of the photodiode is > 1000 μm2, the degree to which the sensor performance increases as the photodiode size increases, is reduced. As a result, considering the fill factor, pixel-pitch > 32 μm is not necessary to achieve high-efficiency image quality. In addition, poor image quality is to be expected unless special sensor-design techniques are included for sensors with a pixel pitch of 25 μm or less.

Mid-frequency MTF compensation of optical sparse aperture system.

PubMed

Zhou, Chenghao; Wang, Zhile

2018-03-19

Optical sparse aperture (OSA) can greatly improve the spatial resolution of optical system. However, because of its aperture dispersion and sparse, its mid-frequency modulation transfer function (MTF) are significantly lower than that of a single aperture system. The main focus of this paper is on the mid-frequency MTF compensation of the optical sparse aperture system. Firstly, the principle of the mid-frequency MTF decreasing and missing of optical sparse aperture are analyzed. This paper takes the filling factor as a clue. The method of processing the mid-frequency MTF decreasing with large filling factor and method of compensation mid-frequency MTF with small filling factor are given respectively. For the MTF mid-frequency decreasing, the image spatial-variant restoration method is proposed to restore the mid-frequency information in the image; for the mid-frequency MTF missing, two images obtained by two system respectively are fused to compensate the mid-frequency information in optical sparse aperture image. The feasibility of the two method are analyzed in this paper. The numerical simulation of the system and algorithm of the two cases are presented using Zemax and Matlab. The results demonstrate that by these two methods the mid-frequency MTF of OSA system can be compensated effectively.

Effect of lateral size and thickness on the electronic structure and optical properties of quasi two-dimensional CdSe and CdS nanoplatelets

DOE Office of Scientific and Technical Information (OSTI.GOV)

Bose, Sumanta; Fan, W. J., E-mail: ewjfan@ntu.edu.sg; Zhang, D. H.

2016-04-14

The effect of lateral size and vertical thickness of CdSe and CdS nanoplatelets (NPLs) on their electronic structure and optical properties are investigated using an effective-mass envelope function theory based on the 8-band k ⋅ p model with valence force field considerations. Volumetrically larger NPLs have lower photon emission energy due to limited quantum confinement, but a greater transition matrix element (TME) due to larger electron-hole wavefunction overlap. The optical gain characteristics depend on several factors such as TME, Fermi factor, carrier density, NPL dimensions, material composition, and dephasing rate. There is a red shift in the peak position, moremore » so with an increase in thickness than lateral size. For an increasing carrier density, the gain spectrum undergoes a slight blue shift due to band filling effect. For a fixed carrier density, the Fermi factor is higher for volumetrically larger NPLs and so is the difference between the quasi-Fermi level separation and the effective bandgap. The transparency injection carrier density (and thus input current density threshold) is dimension dependent and falls for volumetrically larger NPLs, as they can attain the requisite exciton count for transparency with a relatively lower density. Between CdSe and CdS, CdSe has lower emission energy due to smaller bandgap, but a higher TME due to lower effective mass. CdS, however, has a higher so hole contribution due to a lower spin-orbit splitting energy. Both CdSe and CdS NPLs are suitable candidates for short-wavelength LEDs and lasers in the visible spectrum, but CdSe is expected to exhibit better optical performance.« less

Gender differences in cardiovascular diseases risk for physical education teachers.

PubMed

Misigoj-Duraković, Marjeta; Duraković, Zijad; Ruzić, Lana; Findak, Vladimir

2004-01-01

The aim of the study was to evaluate the level of habitual physical activity in Croatian physical education (PE) teachers, as well as the existence of some other risk factors for the development of cardiovascular diseases (CVD). The sample consisted of 191 PE teachers aged 24 to 59 years (122 men, mean age 42.6+/-8.76 and 69 women, mean age 40.3+/-8.84;p=0.09). In order to assess the level of habitual physical activity, the teachers were asked to fill in Baecke's questionnaire. The questionnaire comprises 16 items testing physical loads at work, during sport activity and during leisure time. The questionnaire also contains 8 items, each of them representing a certain cardiovascular risk factor. In comparison to average adult employed population, PE teachers have a significantly higher level of sport and leisure time activity, which could have a favorable impact on the incidence of particular risk factors, such as overweight/obesity, systolic hypertension and blood cholesterol level. This is more obvious in females PE teachers who pay more attention to the principles of healthy life style: optimal body weight regulation, low fat diet and higher amount of leisure time physical activity (significantly higher than in male teachers). Female PE teachers who have maintained their active life style decrease the risk of CVD, particularly after the age of 55. Although it is necessary to keep in mind all the limitations of a questionnaire study, this preliminary report leads to the conclusion that male PE teachers, although physically active at job, have still kept sedentary habits, often have maintained heavy smoking habits, are slightly overweight, thus minimizing the positive effects of their demanding workplace. Consequently, average male PE teachers' risk for CVD development corresponds to the risk of general male population.

Primary Nonadherence, Associated Clinical Outcomes, and Health Care Resource Use Among Patients with Rheumatoid Arthritis Prescribed Treatment with Injectable Biologic Disease-Modifying Antirheumatic Drugs.

PubMed

Harnett, James; Wiederkehr, Daniel; Gerber, Robert; Gruben, David; Bourret, Jeffrey; Koenig, Andrew

2016-03-01

Adherence to biologic disease-modifying antirheumatic drugs (bDMARDs) among patients with rheumatoid arthritis (RA) is often suboptimal in routine clinical practice. Low or nonadherence can reduce the effectiveness of bDMARD therapies. To evaluate filling of newly prescribed initial bDMARDs for the treatment of RA and evaluate potential for characterizing treatment decisions and patient outcomes. In this retrospective cohort analysis, patients aged ≥ 18 years with an RA diagnosis (ICD-9-CM code 714.xx) were selected from a de-identified database of clinical information from the Electronic Health Record (EHR; Humedica) database linked to health care claims (Optum) from commercial and Medicare Advantage health plans (2007-2013). The first biologic prescription date in EHR was the index date. Patients were categorized as filling the prescription within 30 days (early fillers), 31-180 days (late fillers), or not at all within 180 days (nonfillers) of index date. Of 373 patients meeting inclusion criteria, 170 (45.6%), 59 (15.8%), and 144 (38.6%) were categorized as early fillers, late fillers, and nonfillers, respectively. Most prescriptions were written or ordered for tumor necrosis factor inhibitors (88.7%). Compared with late and nonfillers, early fillers were younger and more likely to be female, with higher pain scores (among those reporting pain scores) and RA severity scores pre-index, and filled more prescriptions for any reason pre-index. More nonfillers (66.0%) were Medicare patients than early (17.7%) and late (35.6%) fillers. During days 0-30 post-index, conventional synthetic DMARD use was greatest for early fillers (45.9%) and lowest among nonfillers (24.3%); however, during days 31-180 post-index, the proportion was highest for late fillers (61.0%) and lowest for nonfillers (35.4%). Of early fillers, 12.9% did not fill/receive a bDMARD after 30 days. Only 23 patients had pre/post-index pain scores, and 47 patients had a rationale for stopping or not filling a bDMARD. In patients with pharmacy and medical coverage for 180 days post-index, early fillers had greater RA-related pharmacy and medical resource use and costs than late and nonfillers combined. These findings confirm a high rate of primary nonadherence to bDMARDs among patients with RA.

The filling of powdered herbs into two-piece hard capsules using hydrogenated cotton seed oil as lubricant.

PubMed

Aling, Joanna; Podczeck, Fridrun

2012-11-20

The aim of this work was to investigate the plug formation and filling properties of powdered herbal leaves using hydrogenated cotton seed oil as an alternative lubricant. In a first step, unlubricated and lubricated herbal powders were studied on a small scale using a plug simulator, and low-force compression physics and parameterization techniques were used to narrow down the range in which the optimum amount of lubricant required would be found. In a second step these results were complemented with investigations into the flow properties of the powders based on packing (tapping) experiments to establish the final optimum lubricant concentration. Finally, capsule filling of the optimum formulations was undertaken using an instrumented tamp filling machine. This work has shown that hydrogenated cotton seed oil can be used advantageously for the lubrication of herbal leaf powders. Stickiness as observed with magnesium stearate did not occur, and the optimum lubricant concentration was found to be less than that required for magnesium stearate. In this work, lubricant concentrations of 1% or less hydrogenated cotton seed oil were required to fill herbal powders into capsules on the instrumented tamp-filling machine. It was found that in principle all powders could be filled successfully, but that for some powders the use of higher compression settings was disadvantageous. Relationships between the particle size distributions of the powders, their flow and consolidation as well as their filling properties could be identified by multivariate statistical analysis. The work has demonstrated that a combination of the identification of plug formation and powder flow properties is helpful in establishing the optimum lubricant concentration required using a small quantity of powder and a powder plug simulator. On an automated tamp-filling machine, these optimum formulations produced satisfactory capsules in terms of coefficient of fill weight variability and capsule weight. Copyright © 2012 Elsevier B.V. All rights reserved.

Gap Fill Materials Using Cyclodextrin Derivatives in ArF Lithography

NASA Astrophysics Data System (ADS)

Takei, Satoshi; Shinjo, Tetsuya; Sakaida, Yasushi; Hashimoto, Keisuke

2007-11-01

High planarizing gap fill materials based on β-cyclodextrin in ArF photoresist under-layer materials have been developed for fast etching in CF4 gas. Gap fill materials used in the via-first dual damascene process need to have high etch rates to prevent crowning or fencing on top of the trench after etching and a small thickness bias between the dense and blanket areas to minimize issues observed during trench lithography by narrowing the process latitude. Cyclodextrin is a circular oligomer with a nanoscale porous structure that has a high number of oxygen atoms, as calculated using the Ohnishi parameter, providing high etch rates. Additionally, since gap fill materials using cyclodextrin derivatives have low viscosities and molecular weights, they are expected to exhibit excellent flow properties and minimal thermal shrinkage during baking. In this paper, we describe the composition and basic film properties of gap fill materials; planarization in the via-first dual damascene process and etch rates in CF4 gas compared with dextrin with α-glycoside bonds in polysaccharide, poly(2-hydroxypropyl methacrylate) and poly(4-hydroxystyrene). The β-cyclodextrin used in this study was obtained by esterifying the hydroxyl groups of dextrin resulting in improved wettability on via substrates and solubility in photoresist solvents such as propylene glycol monomethyl ether, propylene glycol monomethyl ether acetate and ethyl lactate. Gap fill materials using cyclodextrin derivatives showed good planarization and via filling performance without observing voids in via holes. In addition to superior via filling performance, the etch rate of gap fill materials using β-cyclodextrin derivatives was 2.8-2.9 times higher than that of an ArF photoresist, evaluated under CF4 gas conditions by reactive ion etching. These results were attributed to the combination of both nanoscale porous structures and a high density of oxygen atoms in our gap fill materials using cyclodextrin derivatives. The cyclodextrin derivatives may be applicable as a new type of sacrificial material under the photoresist in ArF lithography.

Evaluation of Radiopacity of Bulk-fill Flowable Composites Using Digital Radiography.

PubMed

Tarcin, B; Gumru, B; Peker, S; Ovecoglu, H S

2016-01-01

New flowable composites that may be bulk-filled in layers up to 4 mm are indicated as a base beneath posterior composite restorations. Sufficient radiopacity is one of the several important requirements such materials should meet. The aim of this study was to evaluate the radiopacity of bulk-fill flowable composites and to provide a comparison with conventional flowable composites using digital imaging. Ten standard specimens (5 mm in diameter, 1 mm in thickness) were prepared from each of four different bulk-fill flowable composites and nine different conventional flowable composites. Radiographs of the specimens were taken together with 1-mm-thick tooth slices and an aluminum step wedge using a digital imaging system. For the radiographic exposures, a storage phosphor plate and a dental x-ray unit at 70 kVp and 8 mA were used. The object-to-focus distance was 30 cm, and the exposure time was 0.2 seconds. The gray values of the materials were measured using the histogram function of the software available with the system, and radiopacity was calculated as the equivalent thickness of aluminum. The data were analyzed statistically (p<0.05). All of the tested bulk-fill flowable composites showed significantly higher radiopacity values in comparison with those of enamel, dentin, and most of the conventional flowable composites (p<0.05). Venus Bulk Fill (Heraeus Kulzer) provided the highest radiopacity value, whereas Arabesk Flow (Voco) showed the lowest. The order of the radiopacity values for the bulk-fill flowable composites was as follows: Venus Bulk Fill (Heraeus Kulzer) ≥ X-tra Base (Voco) > SDR (Dentsply DeTrey) ≥ Filtek Bulk Fill (3M ESPE). To conclude, the bulk-fill flowable restorative materials, which were tested in this study using digital radiography, met the minimum standard of radiopacity specified by the International Standards Organization.

Offshoring of healthcare services: the case of US-India trade in medical transcription services.

PubMed

Kshetri, Nir; Dholakia, Nikhilesh

2011-01-01

- The issue of offshore outsourcing of healthcare services is a critical but little-examined problem in healthcare research. The purpose of this study is to contribute to filling this void. A library-based study was carried out of the development of the Indian medical transcription offshoring industry. Findings- Cost-saving potential and the degree of outsourceability are higher for medical transcription compared with most services. Offshoring experience, typically in a low-value BPO, helps to enhance productivity and international linkages required for the success of medical transcription. Research limitations/implications - An important area of future research concerns comparing India's factor endowments in medical transcription outsourcing with other services. Further research is also needed to examine how India differs from its regional competitors in terms of factors endowments associated with these services. Another extension would be to investigate the drivers of offshoring of higher value services such as radiological readings. Practical implications - ICT infrastructures needed for outsourcing require much less investment compared with leading capital-intensive industries. The development patterns of the Indian medical and offshoring industries indicate that India may attract higher skilled medical functions in the future. The Indian offshoring industry is shifting its focus from BPO to knowledge process outsourcing (KPO). Developing countries need to shift to greater automation and greater levels of skill training to retain and reinforce their comparative advantages. This paper's greatest value stems from the fact that it examines the drivers of a new but rapidly growing healthcare industry.

Characterization of Emissions from Liquid Fuel and Propane Open Burns.

PubMed

Aurell, Johanna; Hubble, David; Gullett, Brian K; Holder, Amara; Washburn, Ephraim; Tabor, Dennis

2017-11-07

The effect of accidental fires are simulated to understand the response of items such as vehicles, fuel tanks, and military ordnance and to remediate the effects through re-design of the items or changes in operational procedures. The comparative combustion emissions of using jet propellant (JP-5) liquid fuel pools or a propane manifold grid to simulate the effects of accidental fires was investigated. A helium-filled tethered aerostat was used to maneuver an instrument package into the open fire plumes to measure CO, CO 2 , fine particulate matter (PM 2.5 ), polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), and elemental/organic/total carbon (EC/OC/TC). The results showed that all emissions except CO 2 were significantly higher from JP-5 burns than from propane. The major portion of the PM mass from fires of both fuels was less than 1 μm in diameter and differed in carbon content. The PM 2.5 emission factor from JP-5 burns (129 ± 23 g/kg Fuel c ) was approximately 150 times higher than the PM 2.5 emission factor from propane burns (0.89 ± 0.21 g/kg Fuel c ). The PAH emissions as well as some VOCs were more than one hundred times higher for the JP-5 burns than the propane burns. Using the propane test method to study flammability responses, the environmental impact of PM 2.5 , PAHs, and VOCs would be reduced by 2300, 700, and 100 times per test, respectively.

Adverse childhood experiences: assessing the impact on health and school engagement and the mitigating role of resilience.

PubMed

Bethell, Christina D; Newacheck, Paul; Hawes, Eva; Halfon, Neal

2014-12-01

The ongoing longitudinal Adverse Childhood Experiences Study of adults has found significant associations between chronic conditions; quality of life and life expectancy in adulthood; and the trauma and stress associated with adverse childhood experiences, including physical or emotional abuse or neglect, deprivation, or exposure to violence. Less is known about the population-based epidemiology of adverse childhood experiences among US children. Using the 2011-12 National Survey of Children's Health, we assessed the prevalence of adverse childhood experiences and associations between them and factors affecting children's development and lifelong health. After we adjusted for confounding factors, we found lower rates of school engagement and higher rates of chronic disease among children with adverse childhood experiences. Our findings suggest that building resilience-defined in the survey as "staying calm and in control when faced with a challenge," for children ages 6-17-can ameliorate the negative impact of adverse childhood experiences. We found higher rates of school engagement among children with adverse childhood experiences who demonstrated resilience, as well as higher rates of resilience among children with such experiences who received care in a family-centered medical home. We recommend a coordinated effort to fill knowledge gaps and translate existing knowledge about adverse childhood experiences and resilience into national, state, and local policies, with a focus on addressing childhood trauma in health systems as they evolve during ongoing reform. Project HOPE—The People-to-People Health Foundation, Inc.

Theory of g-factor enhancement in narrow-gap quantum well heterostructures.

PubMed

Krishtopenko, S S; Gavrilenko, V I; Goiran, M

2011-09-28

We report on the study of the exchange enhancement of the g-factor in the two-dimensional (2D) electron gas in n-type narrow-gap semiconductor heterostructures. Our approach is based on the eight-band k⋅p Hamiltonian and takes into account the band nonparabolicity, the lattice deformation, the spin-orbit coupling and the Landau level broadening in the δ-correlated random potential model. Using the 'screened' Hartree-Fock approximation we demonstrate that the exchange g-factor enhancement not only shows maxima at odd values of Landau level filling factors but, due to the conduction band nonparabolicity, persists at even filling factor values as well. The magnitude of the exchange enhancement, the amplitude and the shape of the g-factor oscillations are determined by both the screening of the electron-electron interaction and the Landau level width. The 'enhanced' g-factor values calculated for the 2D electron gas in InAs/AlSb quantum well heterostructures are compared with our earlier experimental data and with those obtained by Mendez et al (1993 Phys. Rev. B 47 13937) in magnetic fields up to 30 T.

Major factors controlling fracture development in the Middle Permian Lucaogou Formation tight oil reservoir, Junggar Basin, NW China

NASA Astrophysics Data System (ADS)

Zhang, Chen; Zhu, Deyu; Luo, Qun; Liu, Luofu; Liu, Dongdong; Yan, Lin; Zhang, Yunzhao

2017-09-01

Natural fractures in seven wells from the Middle Permian Lucaogou Formation in the Junggar Basin were evaluated in light of regional structural evolution, tight reservoir geochemistry (including TOC and mineral composition), carbon and oxygen isotopes of calcite-filled fractures, and acoustic emission (AE). Factors controlling the development of natural fractures were analyzed using qualitative and/or semi-quantitative techniques, with results showing that tectonic factors are the primary control on fracture development in the Middle Permian Lucaogou Formation of the Junggar Basin. Analyses of calcite, dolomite, and TOC show positive correlations with the number of fractures, while deltaic lithofacies appear to be the most favorable for fracture development. Mineral content was found to be a major control on tectonic fracture development, while TOC content and sedimentary facies mainly control bedding fractures. Carbon and oxygen isotopes vary greatly in calcite-filled fractures (δ13C ranges from 0.87‰ to 7.98‰, while δ18O ranges from -12.63‰ to -5.65‰), indicating that fracture development increases with intensified tectonic activity or enhanced diagenetic alteration. By analyzing the cross-cutting relationships of fractures in core, as well as four Kaiser Effect points in the acoustic emission curve, we observed four stages of tectonic fracture development. First-stage fractures are extensional, and were generated in the late Triassic, with calcite fracture fills formed between 36.51 °C and 56.89 °C. Second-stage fractures are shear fractures caused by extrusion stress from the southwest to the northeast, generated by the rapid uplift of the Tianshan in the Middle and Late Jurassic; calcite fracture fills formed between 62.91 °C and 69.88 °C. Third-stage fractures are NNW-trending shear fractures that resulted from north-south extrusion and thrusting in a foreland depression along the front of the Early Cretaceous Bogda Mountains. Calcite fracture fills formed between 81.74 °C and 85.43 °C. Fourth-stage fractures inherited the tectonic framework of the third stage, resulting in fractures with the same orientation, but without calcite filling. By differentiating the various stages of fracture development, we were able to better understand the origin of fractures in tight oil reservoirs and their significance for exploration and development.

Measuring Magnetic Oscillations in the Solar Photosphere: Coordinated Observations with MDI, ASP and MWO

NASA Astrophysics Data System (ADS)

Norton, A. A.; Ulrich, R. K.

2000-03-01

A comprehensive observing effort was undertaken to simultaneously obtain full Stokes profiles as well as longitudinal magnetogram maps of a positive plage region on 8 December, 1998 with the Michelson Doppler Imager, the Advanced Stokes Polarimeter and Mt. Wilson Observatory magnetograph. We compare 1.2'' spatially-averaged signals of velocities as well as filter magnetograph longitudinal flux signals with Stokes determined fluctuations in filling factor, field inclination, magnetic flux and field strength. The velocity signals are in excellent agreement. Michelson Doppler Imager magnetic flux correlates best with fluctuations in the Advanced Stokes Polarimeter filling factor, not inclination angle or field strength. A correlated flux and filling factor change in the absence of a field strength fluctuation can be understood in terms of internally unperturbed flux tubes being buffeted by external pressure fluctuations. The 12.5'' square aperture spatially averaged Mt. Wilson magnetograph signals are compared with Michelson Doppler Imager signals from the corresponding observing area. Velocity signals are in superb agreement. Magnetic signals exhibit similar oscillatory behavior. Lack of Advanced Stokes Polarimeter data for this time excludes interpretation of magnetic fluctuations as due to filling factor or field inclination angle. Mt. Wilson Observatory simultaneous sampling of the nickel and sodium spectral line profiles with several wing pairs allowed inter-comparison of signals from different heights of formation. Slight phase shifts and large propagation speeds for the velocity signals are indicative of modified standing waves. Phase speeds associated with magnetic signals are characteristic of photospheric Alfvén speeds for plage fields. The phase speed increase with height agrees with the altitude dependence of the Alfvén speed. The observed fluctuations and phases are interpreted as a superposition of signatures from the horizontal component of the driving mechanism sweeping the field lines in/out of the resolution area and the magnetic response of the flux tube to this buffeting.

Raman study of the repair of surgical bone defects grafted with biphasic synthetic microgranular HA + β-calcium triphosphate and irradiated or not with λ780 nm laser.

PubMed

Soares, Luiz Guilherme P; Marques, Aparecida Maria C; Barbosa, Artur Felipe S; Santos, Nicole R; Aciole, Jouber Mateus S; Souza, Caroline Mathias C; Pinheiro, Antonio Luiz B; Silveira, Landulfo

2014-09-01

The treatment of bone loss due to different etiologic factors is difficult, and many techniques aim to improve repair, including a wide range of biomaterials and, recently, photobioengineering. This work aimed to assess, through Raman spectroscopy, the level of bone mineralization using the intensities of the Raman peaks of both inorganic (∼ 960, ∼ 1,070, and ∼ 1,077 cm(-1)) and organic (∼ 1,454 and ∼ 1,666 cm(-1)) contents of bone tissue. Forty rats were divided into four groups each subdivided into two subgroups according to the time of killing (15 and 30 days). Surgical bone defects were made on femur of each animal with a trephine drill. On animals of group Clot, the defect was filled only by blood clot; on group Laser, the defect filled with the clot was further irradiated. On animals of groups Biomaterial and Laser + Biomaterial, the defect was filled by biomaterial and the last one was further irradiated (λ780 nm, 70 mW, Φ ∼ 0.4 cm(2), 20 J/cm(2) session, 140 J/cm(2) treatment) in four points around the defect at 48-h intervals and repeated for 2 weeks. At both 15th and 30th day following killing, samples were taken and analyzed by Raman spectroscopy. At the end of the experimental time, the intensities of both inorganic and organic contents were higher on group Laser + Biomaterial. It is concluded that the use of laser phototherapy associated to biomaterial was effective in improving bone healing on bone defects as a result of the increasing deposition of calcium hydroxyapatite measured by Raman spectroscopy.

Employment, gender, and smoking cessation outcomes in low-income smokers using nicotine replacement therapy.

PubMed

Burgess, Diana J; Fu, Steven S; Noorbaloochi, Siamak; Clothier, Barbara A; Ricards, Jennifer; Widome, Rachel; van Ryn, Michelle

2009-12-01

This study examines the presence and correlates of gender disparities in smoking cessation among lower income smokers prescribed nicotine replacement medication. We examined quit rates (7-day abstinence point prevalence) among a cohort of smokers who filled prescriptions for nicotine replacement (N = 1,782), using Minnesota Health Care Programs' (e.g., Medicaid) pharmacy claims databases (2005-2006) and mixed-mode survey protocols. A cohort of smokers who recently filled a prescription for nicotine replacement was stratified by race, and then subjects were selected by simple random sample from each race, oversampling the nonWhite groups (N = 1,782). The primary outcome was point prevalence of 7-day abstinence, and outcomes were assessed about 8 months after the nicotine replacement therapy (NRT) index prescription fill date using a mixed-mode survey protocol. Final interaction models were constructed using backward elimination. Abstinence rates were 11.4% among women and 19.2% among men (p = .02) and remained marginally significant after controlling for demographics, mental and physical health, period of cigarette abstinence, social environment, religious attendance, perceived stress, and NRT prescription type (p = .08). There was a significant Gender x Employment interaction (p = .02). Among men, quit rates were higher among the employed (26%) compared with the unemployed (16%); among women, quit rates were lower among those who were employed (8%) compared with those who were unemployed (14%). Results suggest the need for research on factors specific to women's work roles or workplaces that inhibit cessation as well as cessation programs tailored to low-income, employed female smokers. On-site workplace interventions and flexible counseling programs may be especially beneficial.

Nonpolar p-GaN/n-Si heterojunction diode characteristics: a comparison between ensemble and single nanowire devices

NASA Astrophysics Data System (ADS)

Patsha, Avinash; Pandian, Ramanathaswamy; Dhara, Sandip; Tyagi, A. K.

2015-10-01

The electrical and photodiode characteristics of ensemble and single p-GaN nanowire and n-Si heterojunction devices were studied. Ideality factor of the single nanowire p-GaN/n-Si device was found to be about three times lower compared to that of the ensemble nanowire device. Apart from the deep-level traps in p-GaN nanowires, defect states due to inhomogeneity in Mg dopants in the ensemble nanowire device are attributed to the origin of the high ideality factor. Photovoltaic mode of the ensemble nanowire device showed an improvement in the fill-factors up to 60% over the single nanowire device with fill-factors up to 30%. Responsivity of the single nanowire device in the photoconducting mode was found to be enhanced by five orders, at 470 nm. The enhanced photoresponse of the single nanowire device also confirms the photoconduction due to defect states in p-GaN nanowires.

A Semi-parametric Multivariate Gap-filling Model for Eddy Covariance Latent Heat Flux

NASA Astrophysics Data System (ADS)

Li, M.; Chen, Y.

2010-12-01

Quantitative descriptions of latent heat fluxes are important to study the water and energy exchanges between terrestrial ecosystems and the atmosphere. The eddy covariance approaches have been recognized as the most reliable technique for measuring surface fluxes over time scales ranging from hours to years. However, unfavorable micrometeorological conditions, instrument failures, and applicable measurement limitations may cause inevitable flux gaps in time series data. Development and application of suitable gap-filling techniques are crucial to estimate long term fluxes. In this study, a semi-parametric multivariate gap-filling model was developed to fill latent heat flux gaps for eddy covariance measurements. Our approach combines the advantages of a multivariate statistical analysis (principal component analysis, PCA) and a nonlinear interpolation technique (K-nearest-neighbors, KNN). The PCA method was first used to resolve the multicollinearity relationships among various hydrometeorological factors, such as radiation, soil moisture deficit, LAI, and wind speed. The KNN method was then applied as a nonlinear interpolation tool to estimate the flux gaps as the weighted sum latent heat fluxes with the K-nearest distances in the PCs’ domain. Two years, 2008 and 2009, of eddy covariance and hydrometeorological data from a subtropical mixed evergreen forest (the Lien-Hua-Chih Site) were collected to calibrate and validate the proposed approach with artificial gaps after standard QC/QA procedures. The optimal K values and weighting factors were determined by the maximum likelihood test. The results of gap-filled latent heat fluxes conclude that developed model successful preserving energy balances of daily, monthly, and yearly time scales. Annual amounts of evapotranspiration from this study forest were 747 mm and 708 mm for 2008 and 2009, respectively. Nocturnal evapotranspiration was estimated with filled gaps and results are comparable with other studies. Seasonal and daily variability of latent heat fluxes were also discussed.

A conceptual framework for managing modifiable risk factors for cardiovascular diseases in Fiji.

PubMed

Witter, Trevor; Poudevigne, Melanie; Lambrick, Danielle M; Faulkner, James; Lucero, Adam A; Page, Rachel; Perry, Lane G; Tarrant, Michael A; Stoner, Lee

2015-03-01

The current review will look at modifiable lifestyle (physical inactivity, poor nutrition, risky alcohol behavior and cigarette smoking) and cardio-metabolic (obesity, diabetes mellitus, high cholesterol and high blood pressure) cardiovascular disease (CVD) risk factors among Indigenous-Fijian and Indo-Fijian subgroups. A framework for monitoring and managing these risk factors will be presented. National health surveys were identified where available. Electronic databases identified sources for filling missing data. The most relevant data were identified, organized and synthesized. Compared to Indo-Fijians, Indigenous-Fijians have higher rates of obesity (17% vs 11%) and hypertension (21% vs 16%), but lower rates of diabetes mellitus (12% vs 21%) and high cholesterol (33% vs 39%). Indigenous-Fijians report higher rates of prescribed physical activity (25% vs 21%), but poorer recommended vegetable intake (48% vs 56%), greater risky alcohol behavior (17% vs 15%) and a much greater prevalence of cigarette smoking (45% vs 24%). Both Indigenous-Fijians and Indo-Fijians report a low prevalence of recommended fruit intake (17% vs 15%). Fiji is progressing through demographic and epidemiological transitions, including a decline in infectious diseases and improved life expectancy. However, in concert with other developing nations, 'modernization' is accompanied by increased mortality from non-communicable diseases, with CVD being the most prevalent. This transition has been associated with changes to socio-cultural aspects of Fiji, including poor lifestyle choices that may contribute to a cluster of cardio-metabolic conditions which precede CVD. © Royal Society for Public Health 2013.

Characterization of an improved 1-3 piezoelectric composite by simulation and experiment.

PubMed

Zhong, Chao; Wang, Likun; Qin, Lei; Zhang, Yanjun

2017-06-16

To increase electromechanical coupling factor of 1-3 piezoelectric composite and reduce its bending deformation under external stress, an improved 1-3 piezoelectric composite is developed. In the improved structure, both epoxy resin and silicone rubber are used as polymer material. The simulation model of the improved 1-3 piezoelectric composite was established using the finite element software ANSYS. The relationship of the performance of the improved composite to the volume percentage of silicone rubber was determined by harmonic response analysis and the bending deformation under external stress was simulated by static analysis. The improved composite samples were prepared by cutting and filling methods, and the performance was tested. The feasibility of the improved structure was verified by finite element simulation and experiment. The electromechanical coupling factor of the improved composite can reach 0.67 and meanwhile the characteristic impedance can decline to 13 MRayl. The electromechanical coupling factor of the improved composite is higher than that of the composite with only epoxy resin as the polymer and the improved composite can reduce bending deformation. Comparison of simulation and experiment, the results of the experiment are in general agreement with those from the simulation. However, most experimental values were higher than the simulation results, and the abnormality of the test results was also more obvious than that of the simulation. These findings may be attributed to slight difference in the material parameters of simulation and experiment.

Gallbladder Nonvisualization in Cholecystectomy: A Factor for Conversion.

PubMed

Slack, Daniel R; Grisby, Shaunda; Dike, Uzoamaka Kimberly; Kohli, Harjeet

2018-01-01

Many risk factors have been identified in minimally invasive cholecystectomies that lead to higher complications and conversion rates. No study that we encountered looked at nonvisualization of the gallbladder (GB) during surgery as a risk factor. We hypothesized that nonvisualization was associated with an increased risk of complications and could be an early intraoperative identifier of a higher risk procedure. Recognizing this could allow surgeons to be aware of potential risks and to be more likely to convert to open for the safety of the patient. We looked at minimally invasive cholecystectomies performed at our institution from January 2015 through April 2016 and had the performing resident fill out a survey after the surgery. Outcomes were conversion rates, intraoperative complications, and blood loss and were analyzed via Pearson χ 2 test or Mann-Whitney U test. The primary outcome showed a conversion rate of 37% in nonvisualized GBs versus 0% in visualized ( P = .001). Secondary outcomes showed significant differences in GB perforations (74% vs 13%, P = .001), omental vessel bleeding (16% vs. 0%, P = .005), and EBL (46 mL vs 29 mL, P = .001). Intraoperative nonvisualization of the GB after adequate positioning caused significantly increased risk of intraoperative complications and conversion. This knowledge could be useful during intraoperative assessment, to decide whether a case should be continued as a minimally invasive procedure or converted early to help reduce risk to the patient. Further randomized controlled studies should be performed to further demonstrate the value of this assessment.

Doppler echocardiographic analysis of left ventricular filling in treated hypertensive patients.

PubMed

Phillips, R A; Coplan, N L; Krakoff, L R; Yeager, K; Ross, R S; Gorlin, R; Goldman, M E

1987-02-01

Early detection and prevention of cardiac dysfunction is an important goal in the management of hypertensive patients. In this study, Doppler echocardiography was used to evaluate the pattern of left ventricular diastolic filling in 38 subjects: 18 treated hypertensive patients (blood pressure 141 +/- 17/83 +/- 10 mm Hg, mean +/- SD) without other coronary risk factors and 20 risk-free normotensive subjects of similar age (47 +/- 10 and 49 +/- 13 years, respectively). Peak velocity of late left ventricular filling due to the atrial contraction was greater in hypertensive compared with normotensive subjects (69 +/- 14 versus 52 +/- 13 cm/s; p less than 0.001). Peak velocity of late filling was significantly greater in hypertensive versus normotensive subjects in those aged 50 years or younger and those older than age 50 (65 +/- 12 versus 50 +/- 11; p less than 0.01 and 75 +/- 15 versus 56 +/- 15 cm/s; p less than 0.05, respectively). In hypertensive subjects, peak velocity of late filling did not correlate with routine indexes of hypertensive heart disease (including posterior wall thickness and left ventricular mass), systolic and diastolic blood pressure or duration of hypertension. These results indicate that increased velocity of late left ventricular filling may be independent of left ventricular hypertrophy and persist despite effective blood pressure control.

Changes in Rates of Shore Retreat, Lake Michigan, 1967-1976.

DTIC Science & Technology

1979-12-01

D.C., Apr. 1946. BERG, D.W., "Factors Affecting Beach Nourishment at Presque Isle Peninsula, Erie , Pennsylvania ," Proceedings of the Ninth Conference on...concern the behavior of beach fill at Presque Isle Peninsula on Lake Erie . Guidelines for moni- toring the effect of shore protection works in the Great...NTIS AD 631 520). BERG, D.W., and DUANE, D.B., "Effects of Particle Size and Distribution on Stability of Artificially Filled Beach, Presque Isle

[Therapeutic effect of double fill nine tastes soup in treating recurrent respiratory infection (RRI) and change of immune function in children].

PubMed

Wang, Youcheng; Zhang, Lijuan; Hu, Guohua; Wang, Menghe; Tang, Xiaoyuan; Guo, Hui; Shi, Yimei; Chen, Shufang; Shi, Changchun

2012-04-01

To investigate the therapeutic effect of double fill nine tastes soup in treating children recurrent respiratory infection (RRTI) and the change of immune function. 77 RRTI patients were randomly selected into observation and control groups. The observation group was treated with Chinese medicine- double fill nine tastes soup,water frying points 2 times oral. The control was treated with transfer factor oral liquid,every 10 mL,2 times daily oral. Treatment periods were both two months. IgA, IgG, IgM and IL-12, TNF-alpha, INF-gamma were detected before and after treatment to assess the clinical effects and the changes of immune factors, meanwhile, a health group was established. Before treatment, compared with the health group, the serum IgA, IgG, IgM, IgE, IL-12, TNF-alpha, IFN-gamma in both groups were significantly different (P < 0.01). After treatment, the ratio of IgA, IgG, Ig M, IL-12, TNF-alpha, IFN-gamma in two groups were significantly different (P < 0.01). Compared with the recurrence rate and clinical effects, the observation group was better than control, and the differences were significant (P < 0.01). Double fill nine tastes soup has significant effects in treating recurrent respiratory infection (RRI) and enhance the immune function in children.

Polystyrene Foam Products Equation of State as a Function of Porosity and Fill Gas

NASA Astrophysics Data System (ADS)

Mulford, R. N.; Swift, D. C.

2009-12-01

An accurate EOS for polystyrene foam is necessary for analysis of numerous experiments in shock compression, inertial confinement fusion, and astrophysics. Plastic to gas ratios vary between various samples of foam, according to the density and cell-size of the foam. A matrix of compositions has been investigated, allowing prediction of foam response as a function of the plastic-to-air ratio. The EOS code CHEETAH allows participation of the air in the decomposition reaction of the foam. Differences between air-filled, Ar-blown, and CO2-blown foams are investigated, to estimate the importance of allowing air to react with products of polystyrene decomposition. O2-blown foams are included in some comparisons, to amplify any consequences of reaction with oxygen in air. He-blown foams are included in some comparisons, to provide an extremum of density. Product pressures are slightly higher for oxygen-containing fill gases than for non-oxygen-containing fill gases. Examination of product species indicates that CO2 decomposes at high temperatures.

Mercury concentration in maternal serum, cord blood, and placenta in patients with amalgam dental fillings: effects on fetal biometric measurements.

PubMed

Bedir Findik, Rahime; Celik, Huseyin Tugrul; Ersoy, Ali Ozgur; Tasci, Yasemin; Moraloglu, Ozlem; Karakaya, Jale

2016-11-01

We aimed to determine the extent to which mercury is transmitted from the mother to fetus via the umbilical cord in patients with amalgam dental fillings, and its effect on fetal biometric measurements. Twenty-eight patients as the study group with amalgam fillings, and 32 of them as the control group were included in this prospective case-control study. The mercury levels were measured in the maternal and cord venous sera, and the placental samples. Two groups were compared in terms of these and the fetal/neonatal biometric measurements. In the study group, the maternal and umbilical cord mercury levels were found to be significantly higher than those from the control group (p = 0.006 and p = 0.010, respectively). These high levels did not affect the fetal biometric measurements. The presence of high serum mercury levels in pregnant women with amalgam fillings is important, and warrants further long-term studies in order to investigate the fetal neurological effects as well.

Perceived Housing Discrimination and Self-Reported Health: How Do Neighborhood Features Matter?

PubMed

Yang, Tse-Chuan; Chen, Danhong; Park, Kiwoong

2016-12-01

While the association between perceived discrimination and health has been investigated, little is known about whether and how neighborhood characteristics moderate this association. We situate discrimination in the housing context and use relative deprivation and social capital perspectives to fill the knowledge gap. We applied multilevel logistic modeling to 9,842 adults in 830 neighborhoods in Philadelphia to examine three hypotheses. First, the detrimental effect of discrimination on self-reported health was underestimated without considering neighborhood features as moderators. The estimated coefficient (β) increased from approximately 0.02 to 1.84 or higher. Second, the negative association between discrimination and self-reported health was enhanced when individuals with discrimination experience lived in neighborhoods with higher housing values (β = 0.42). Third, the adverse association of discrimination with self-reported health was attenuated when people reporting discrimination resided in neighborhoods marked by higher income inequality (β = -4.34) and higher concentrations of single-parent households with children (β = -0.03) and minorities (β = -0.01). We not only confirmed the moderating roles of neighborhood characteristics, but also suggested that the relative deprivation and social capital perspectives could be used to understand how perceived housing discrimination affects self-reported health via neighborhood factors.

Perceived Housing Discrimination and Self-reported Health: How Do Neighborhood Features Matter?

PubMed Central

Yang, Tse-Chuan; Chen, Danhong; Park, Kiwoong

2016-01-01

Background While the association between perceived discrimination and health has been investigated, little is known about whether and how neighborhood characteristics moderate this association. Purpose We situate discrimination in the housing context and use relative deprivation and social capital perspectives to fill the knowledge gap. Methods We applied multilevel logistic modeling to 9,842 adults in 830 neighborhoods in Philadelphia to examine three hypotheses. Results First, the detrimental effect of discrimination on self-reported health was underestimated without considering neighborhood features as moderators. The estimated coefficient (β) increased from approximately 0.02 to 1.84 or higher. Second, the negative association between discrimination and self-reported health was enhanced when individuals with discrimination experience lived in neighborhoods with higher housing values (β= 0.42). Third, the adverse association of discrimination with self-reported health was attenuated when people reporting discrimination resided in neighborhoods marked by higher income inequality (β= −4.34) and higher concentrations of single parent households with children (β= −0.03) and minorities (β= −0.01). Conclusions We not only confirmed the moderating roles of neighborhood characteristics, but also suggested that the relative deprivation and social capital perspectives could be used to understand how perceived housing discrimination affects self-reported health via neighborhood factors. PMID:27306452

Sound transmission loss of composite sandwich panels

NASA Astrophysics Data System (ADS)

Zhou, Ran

Light composite sandwich panels are increasingly used in automobiles, ships and aircraft, because of the advantages they offer of high strength-to-weight ratios. However, the acoustical properties of these light and stiff structures can be less desirable than those of equivalent metal panels. These undesirable properties can lead to high interior noise levels. A number of researchers have studied the acoustical properties of honeycomb and foam sandwich panels. Not much work, however, has been carried out on foam-filled honeycomb sandwich panels. In this dissertation, governing equations for the forced vibration of asymmetric sandwich panels are developed. An analytical expression for modal densities of symmetric sandwich panels is derived from a sixth-order governing equation. A boundary element analysis model for the sound transmission loss of symmetric sandwich panels is proposed. Measurements of the modal density, total loss factor, radiation loss factor, and sound transmission loss of foam-filled honeycomb sandwich panels with different configurations and thicknesses are presented. Comparisons between the predicted sound transmission loss values obtained from wave impedance analysis, statistical energy analysis, boundary element analysis, and experimental values are presented. The wave impedance analysis model provides accurate predictions of sound transmission loss for the thin foam-filled honeycomb sandwich panels at frequencies above their first resonance frequencies. The predictions from the statistical energy analysis model are in better agreement with the experimental transmission loss values of the sandwich panels when the measured radiation loss factor values near coincidence are used instead of the theoretical values for single-layer panels. The proposed boundary element analysis model provides more accurate predictions of sound transmission loss for the thick foam-filled honeycomb sandwich panels than either the wave impedance analysis model or the statistical energy analysis model.

Selective Equilibration of Spin-Polarized Quantum Hall Edge States in Graphene

NASA Astrophysics Data System (ADS)

Amet, F.; Williams, J. R.; Watanabe, K.; Taniguchi, T.; Goldhaber-Gordon, D.

2014-05-01

We report on transport measurements of dual-gated, single-layer graphene devices in the quantum Hall regime, allowing for independent control of the filling factors in adjoining regions. Progress in device quality allows us to study scattering between edge states when the fourfold degeneracy of the Landau level is lifted by electron correlations, causing edge states to be spin and/or valley polarized. In this new regime, we observe a dramatic departure from the equilibration seen in more disordered devices: edge states with opposite spins propagate without mixing. As a result, the degree of equilibration inferred from transport can reveal the spin polarization of the ground state at each filling factor. In particular, the first Landau level is shown to be spin polarized at half filling, providing an independent confirmation of a conclusion of Young et al. [Nat. Phys. 8, 550 (2012)]. The conductance in the bipolar regime is strongly suppressed, indicating that copropagating edge states, even with the same spin, do not equilibrate along PN interfaces. We attribute this behavior to the formation of an insulating ν =0 stripe at the PN interface.

On the generation of a bubbly universe - A quantitative assessment of the CfA slice

NASA Technical Reports Server (NTRS)

Ostriker, J. P.; Strassler, M. J.

1989-01-01

A first attempt is made to calculate the properties of the matter distribution in a universe filled with overlapping bubbles produced by multiple explosions. Each spherical shell follows the cosmological Sedov-Taylor solution until it encounters another shell. Thereafter, mergers are allowed to occur in pairs on the basis of N-body results. At the final epoch, the matrix of overlapping shells is populated with 'galaxies' and the properties of slices through the numerically constructed cube compare well with CfA survey results for specified initial conditions. A statistic is found which measures the distance distribution from uniformly distributed points to the nearest galaxies on the projected plane which appears to provide a good measure of the bubbly character of the galaxy distribution. In a quantitative analysis of the CfA 'slice of the universe', a very good match is found between simulation and the real data for final average bubble radii of (13.5 + or - 1.5)/h Mpc with formal filling factor 1.0-1.5 or actual filling factor of 65-80 percent.

The watercolor effect: a new principle of grouping and figure-ground organization.

PubMed

Pinna, Baingio; Werner, John S; Spillmann, Lothar

2003-01-01

The watercolor effect is perceived when a dark (e.g., purple) contour is flanked by a lighter chromatic contour (e.g., orange). Under these conditions, the lighter color will assimilate over the entire enclosed area. This filling-in determines figure-ground organization when it is pitted against the classical Gestalt factors of proximity, good continuation, closure, symmetry, convexity, as well as amodal completion, and past experience. When it is combined with a given Gestalt factor, the resulting effect on figure-ground organization is stronger than for each factor alone. When the watercolor effect is induced by a dark red edge instead of an orange edge, its figural strength is reduced, but still stronger than without it. Finally, when a uniform surface is filled physically using the color of the orange fringe, figure-ground organization is not different from that for the purple contour only. These findings show that the watercolor effect induced by the edge could be an independent factor, different from the classical Gestalt factors of figure-ground organization. Copyright 2002 Elsevier Science Ltd.

A Simple Geotracer Compositional Correlation Analysis Reveals Oil Charge and Migration Pathways

NASA Astrophysics Data System (ADS)

Yang, Yunlai; Arouri, Khaled

2016-03-01

A novel approach, based on geotracer compositional correlation analysis is reported, which reveals the oil charge sequence and migration pathways for five oil fields in Saudi Arabia. The geotracers utilised are carbazoles, a family of neutral pyrrolic nitrogen compounds known to occur naturally in crude oils. The approach is based on the concept that closely related fields, with respect to filling sequence, will show a higher carbazole compositional correlation, than those fields that are less related. That is, carbazole compositional correlation coefficients can quantify the charge and filling relationships among different fields. Consequently, oil migration pathways can be defined based on the established filling relationships. The compositional correlation coefficients of isomers of C1 and C2 carbazoles, and benzo[a]carbazole for all different combination pairs of the five fields were found to vary extremely widely (0.28 to 0.94). A wide range of compositional correlation coefficients allows adequate differentiation of separate filling relationships. Based on the established filling relationships, three distinct migration pathways were inferred, with each apparently being charged from a different part of a common source kitchen. The recognition of these charge and migration pathways will greatly aid the search for new accumulations.

A Simple Geotracer Compositional Correlation Analysis Reveals Oil Charge and Migration Pathways

PubMed Central

Yang, Yunlai; Arouri, Khaled

2016-01-01

A novel approach, based on geotracer compositional correlation analysis is reported, which reveals the oil charge sequence and migration pathways for five oil fields in Saudi Arabia. The geotracers utilised are carbazoles, a family of neutral pyrrolic nitrogen compounds known to occur naturally in crude oils. The approach is based on the concept that closely related fields, with respect to filling sequence, will show a higher carbazole compositional correlation, than those fields that are less related. That is, carbazole compositional correlation coefficients can quantify the charge and filling relationships among different fields. Consequently, oil migration pathways can be defined based on the established filling relationships. The compositional correlation coefficients of isomers of C1 and C2 carbazoles, and benzo[a]carbazole for all different combination pairs of the five fields were found to vary extremely widely (0.28 to 0.94). A wide range of compositional correlation coefficients allows adequate differentiation of separate filling relationships. Based on the established filling relationships, three distinct migration pathways were inferred, with each apparently being charged from a different part of a common source kitchen. The recognition of these charge and migration pathways will greatly aid the search for new accumulations. PMID:26965479

A Simple Geotracer Compositional Correlation Analysis Reveals Oil Charge and Migration Pathways.

PubMed

Yang, Yunlai; Arouri, Khaled

2016-03-11

A novel approach, based on geotracer compositional correlation analysis is reported, which reveals the oil charge sequence and migration pathways for five oil fields in Saudi Arabia. The geotracers utilised are carbazoles, a family of neutral pyrrolic nitrogen compounds known to occur naturally in crude oils. The approach is based on the concept that closely related fields, with respect to filling sequence, will show a higher carbazole compositional correlation, than those fields that are less related. That is, carbazole compositional correlation coefficients can quantify the charge and filling relationships among different fields. Consequently, oil migration pathways can be defined based on the established filling relationships. The compositional correlation coefficients of isomers of C1 and C2 carbazoles, and benzo[a]carbazole for all different combination pairs of the five fields were found to vary extremely widely (0.28 to 0.94). A wide range of compositional correlation coefficients allows adequate differentiation of separate filling relationships. Based on the established filling relationships, three distinct migration pathways were inferred, with each apparently being charged from a different part of a common source kitchen. The recognition of these charge and migration pathways will greatly aid the search for new accumulations.

The New American Worker.

ERIC Educational Resources Information Center

Cole, Paul F.

U.S. industry and the U.S workplace are changing. More highly skilled jobs are replacing unskilled and semiskilled jobs, and more jobs require higher-order thinking skills. At the same time, the education system is failing to educate young people to fill those jobs in the future. Although a higher percentage of students graduate than ever before,…

Leading Change: How Boards and Presidents Build Exceptional Academic Institutions

ERIC Educational Resources Information Center

MacTaggart, Terrence

2011-01-01

In a time of transformation in higher education, "Leading Change: How Boards and Presidents Build Exceptional Institutions" fills a significant void in leadership literature and focuses on the changing level of board engagement. This book examines 18 institutions, across the spectrum of higher education, at which the board played a…

College Choice and the University Brand: Exploring the Consumer Decision Framework

ERIC Educational Resources Information Center

Stephenson, Amber L.; Heckert, Alex; Yerger, David B.

2016-01-01

Branding in higher education has become increasingly used as a mechanism of differentiation among competitors to attract prospective students. Although branding in higher education is a common phenomenon, little work has been done assessing the college selection process using a brand choice framework. This paper aims to fill the gap by…

Compacted Multiparticulate Systems for Colon-Specific Delivery of Ketoprofen.

PubMed

de Alencar, Rodrigo Gomes; de Oliveira, Aline Carlos; Lima, Eliana Martins; da Cunha-Filho, Marcílio Sérgio Soares; Taveira, Stephânia Fleury; Marreto, Ricardo Neves

2017-08-01

Pellet-containing tablets for colon-specific drug delivery present higher targeting efficiency and lower costs when compared with monolithic tablets and pellet-filled capsules, respectively. In this study, pellets containing ketoprofen were coated with different acrylic polymers and submitted to compaction. The influence of formulation and process factors on film integrity was then evaluated. Pellets were prepared via extrusion-spheronization and coated using two acrylic polymers (Eudragit® FS 30 D and Opadry® 94 k28327, PMMA and PMA, respectively). The resulting pellets were mixed with placebo granules and compressed in a hydraulic press. Multiple regression showed that ketoprofen release from pellet-containing tablets is predominantly influenced by pellet content, hardness, friability, and disintegration time. PMA-containing tablets prepared under low compaction force or with low pellet content showed rapid disintegration (<1 min) and ketoprofen release similar to those of uncompressed coated pellets (∼30% at 360 min of experiment). On the other hand, PMMA-containing tablets showed a higher rupture level, and those prepared with higher pellet content gave rise to a non-disintegrating matrix. Coated pellets were shown to be able to target ketoprofen to the colonic region. Targeting capacity was dependent on the physicochemical characteristics of the tablets.

Unintentional Injuries in Preschool Age Children: Is There a Correlation With Parenting Style and Parental Attention Deficit and Hyperactivity Symptoms.

PubMed

Acar, Ethem; Dursun, Onur Burak; Esin, İbrahim Selcuk; Öğütlü, Hakan; Özcan, Halil; Mutlu, Murat

2015-08-01

Unintentional injuries are the leading cause of death among children. Previous research has shown that most of the injuries occur in and around the home. Therefore, parents have a key role in the occurrence and prevention of injuries. In this study, we examined the relationship among home injuries to children and parental attention deficit hyperactivity disorder (ADHD) symptoms, parental attitudes, and children's behavioral problems.Forty children who were admitted to the emergency department because of home injuries constitute the study group. The control group also consisted of 40 children, who were admitted for mild throat infections. The parents filled out questionnaires assessing parental ADHD, child behavioral problems, and parenting attitudes.Scores were significantly higher for both internalizing disorders and externalizing disorders in study groups. We also found that ADHD symptoms were significantly higher among fathers of injured children compared with fathers of control groups. Democratic parenting was also found to correlate with higher numbers of injuries.Parenting style, as well as the psychopathology of both the parents and children, is important factors in children's injuries. A child psychiatrist visit following an emergency procedure may help to prevent further unintentional injuries to the child.

Factors influencing cost-related nonadherence to medication in older adults: a conceptually based approach.

PubMed

Zivin, Kara; Ratliff, Scott; Heisler, Michele M; Langa, Kenneth M; Piette, John D

2010-01-01

Although multiple noncost factors likely influence a patient's propensity to forego treatment in the face of cost pressures, little is known about how patients' sociodemographic characteristics, physical and behavioral health comorbidities, and prescription regimens influence cost-related nonadherence (CRN) to medications. We sought to determine both financial and nonfinancial factors associated with CRN in a nationally representative sample of older adults. We used a conceptual model developed by Piette and colleagues that describes financial and nonfinancial factors that could increase someone's risk of CRN, including income, comorbidities, and medication regimen complexity. We used data from the 2004 wave of the Health and Retirement Study and the 2005 HRS Prescription Drug Study to examine the influence of factors within each of these domains on measures of CRN (including not filling, stopping, or skipping doses) in a nationally representative sample of Americans age 65+ in 2005. Of the 3071 respondents who met study criteria, 20% reported some form of CRN in 2005. As in prior studies, indicators of financial stress such as higher out-of-pocket payments for medications and lower net worth were significantly associated with CRN in multivariable analyses. Controlling for these economic pressures, relatively younger respondents (ages 65-74) and depressive symptoms were consistent independent risk factors for CRN. Noncost factors influenced patients' propensity to forego treatment even in the context of cost concerns. Future research encompassing clinician and health system factors should identify additional determinants of CRN beyond patients' cost pressures.

Reliability of cystometrically obtained intravesical pressures in patients with neurogenic bladders.

PubMed

Hess, Marika J; Lim, Lance; Yalla, Subbarao V

2002-01-01

Urodynamic studies in patients with neurogenic bladder detect and categorize neurourodynamic states, identify the risk for urologic sequelae, and determine the necessity for interventions. Because urodynamic studies serves as a prognostic indicator and guides patient management, pressure measurements during the study must accurately represent bladder function under physiologic conditions. Because nonphysiologic bladder filling used during conventional urodynamic studies may alter the bladder's accommodative properties, we studied how closely the intravesical pressures obtained before filling cystometry resembled those obtained during the filling phase of the cystometrogram. Twenty-two patients (21 men, 1 woman) with neurogenic bladders underwent standard urodynamic studies. A 16F triple-lumen catheter was inserted into the bladder, and the intravesical pressures were recorded (physiologic volume-specific pressures, PVSP). After emptying the bladder, an equal volume of normal saline solution was reinfused, and the pressures were recorded again (cystometric volume-specific pressure, CVSP). All patients underwent routine fluoroscopically assisted urodynamic testing. The PVSP and the CVSP were compared using the Wilcoxon signed ranks test. P value of .05 was significant. The mean PVSP was 14.5 cmH2O (range, 4-42 cmH2O) and mean CVSP was 20.6 cmH2O (range, 6-70 cmH2O). The CVSP was significantly higher than the PVSP (P = .01). Filling pressures during cystometry (CVSP) were significantly higher than the pressures measured at rest (PVSP). This study also suggests a strong correlation between PVSP and CVSP.

Genetic heritage as a risk factor enabling chilhood obesity.

PubMed

Cunha, Madalena; Aparício, Graça; Duarte, João; Pereira, Anabela; Albuquerque, Carlos; Oliveira, António

2013-05-01

Nowadays, it is an evidence that maternal obesity is an important predictor of obesity in the descendants, not being consensual if that influence comes from the interaction between genes and facilitators family contexts or both. 1) To determinate the prevalence of the child overweight; 2) to classify the nutritional status and metabolic risk of the progenitors; 3) to analyze the effect of the markers of the family metabolic risk in the expression of the illness in the child. Descriptive study composed by 1424 children, average age 4.58 years old and their mothers, average age 34.47 years old, living in several parts of Portugal. The children's anthropometric measures were evaluated and classified according to the NCHS referential (CDC, 2000)(1) and of the progenitors by the orientations of the WHO (2000)(2) and Portugal, DGS (2005).(3) Social demographic data was obtained by filling in the Food Frequency Questionnaire adapted from Rito (2007).(4) The overweight affected 34.3% of the children, (including 17.4% obesity), being the higher values on boys (36.8%) and in 5 year old children (39.5). In 41.9% of the progenitors overweight was noted (12.1% obesity), being higher in mothers with low scholarship, low income, older and living in a rural area. The probability of the child to be overweighted was 1.4 times higher when mothers were overweight, and close to 2 times in the relationship mother/daughter. Others enabling factors were revealed, like weight gain above recommended during pregnancy and a higher weight at birth. Due to the obtained interferences, it is accepted the existence of enabling factors of maternal and child markers in the development of overweight in the child, so that the prevention of child obesity should consider not only the environmental dimension but also the genetic heritage. Copyright © 2013 Elsevier España, S.L. All rights reserved.

Carpel size, grain filling, and morphology determine individual grain weight in wheat.

PubMed

Xie, Quan; Mayes, Sean; Sparkes, Debbie L

2015-11-01

Individual grain weight is a major yield component in wheat. To provide a comprehensive understanding of grain weight determination, the carpel size at anthesis, grain dry matter accumulation, grain water uptake and loss, grain morphological expansion, and final grain weight at different positions within spikelets were investigated in a recombinant inbred line mapping population of bread wheat (Triticum aestivum L.)×spelt (Triticum spelta L.). Carpel size, grain dry matter and water accumulation, and grain dimensions interacted strongly with each other. Furthermore, larger carpels, a faster grain filling rate, earlier and longer grain filling, more grain water, faster grain water absorption and loss rates, and larger grain dimensions were associated with higher grain weight. Frequent quantitative trait locus (QTL) coincidences between these traits were observed, particularly those on chromosomes 2A, 3B, 4A, 5A, 5DL, and 7B, each of which harboured 16-49 QTLs associated with >12 traits. Analysis of the allelic effects of coincident QTLs confirmed their physiological relationships, indicating that the complex but orderly grain filling processes result mainly from pleiotropy or the tight linkages of functionally related genes. After grain filling, distal grains within spikelets were smaller than basal grains, primarily due to later grain filling and a slower initial grain filling rate, followed by synchronous maturation among different grains. Distal grain weight was improved by increased assimilate availability from anthesis. These findings provide deeper insight into grain weight determination in wheat, and the high level of QTL coincidences allows simultaneous improvement of multiple grain filling traits in breeding. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Large quantum rings in the ν > 1 quantum Hall regime.

PubMed

Räsänen, E; Aichinger, M

2009-01-14

We study computationally the ground-state properties of large quantum rings in the filling-factor ν>1 quantum Hall regime. We show that the arrangement of electrons into different Landau levels leads to clear signatures in the total energies as a function of the magnetic field. In this context, we discuss possible approximations for the filling factor ν in the system. We are able to characterize integer-ν states in quantum rings in an analogy with conventional quantum Hall droplets. We also find a partially spin-polarized state between ν = 2 and 3. Despite the specific topology of a quantum ring, this state is strikingly reminiscent of the recently found ν = 5/2 state in a quantum dot.

Simple fabrication of closed-packed IR microlens arrays on silicon by femtosecond laser wet etching

NASA Astrophysics Data System (ADS)

Meng, Xiangwei; Chen, Feng; Yang, Qing; Bian, Hao; Du, Guangqing; Hou, Xun

2015-10-01

We demonstrate a simple route to fabricate closed-packed infrared (IR) silicon microlens arrays (MLAs) based on femtosecond laser irradiation assisted by wet etching method. The fabricated MLAs show high fill factor, smooth surface and good uniformity. They can be used as optical devices for IR applications. The exposure and etching parameters are optimized to obtain reproducible microlens with hexagonal and rectangular arrangements. The surface roughness of the concave MLAs is only 56 nm. This presented method is a maskless process and can flexibly change the size, shape and the fill factor of the MLAs by controlling the experimental parameters. The concave MLAs on silicon can work in IR region and can be used for IR sensors and imaging applications.

Symmetry breaking in the zero-energy Landau level in bilayer graphene.

PubMed

Zhao, Y; Cadden-Zimansky, P; Jiang, Z; Kim, P

2010-02-12

The quantum Hall effect near the charge neutrality point in bilayer graphene is investigated in high magnetic fields of up to 35 T using electronic transport measurements. In the high-field regime, the eightfold degeneracy in the zero-energy Landau level is completely lifted, exhibiting new quantum Hall states corresponding to filling factors nu=0, 1, 2, and 3. Measurements of the activation energy gaps for the nu=2 and 3 filling factors in tilted magnetic fields exhibit no appreciable dependence on the in-plane magnetic field, suggesting that these Landau level splittings are independent of spin. In addition, measurements taken at the nu=0 charge neutral point show that, similar to single layer graphene, the bilayer becomes insulating at high fields.

High external quantum efficiency and fill-factor InGaN/GaN heterojunction solar cells grown by NH3-based molecular beam epitaxy

NASA Astrophysics Data System (ADS)

Lang, J. R.; Neufeld, C. J.; Hurni, C. A.; Cruz, S. C.; Matioli, E.; Mishra, U. K.; Speck, J. S.

2011-03-01

High external quantum efficiency (EQE) p-i-n heterojunction solar cells grown by NH3-based molecular beam epitaxy are presented. EQE values including optical losses are greater than 50% with fill-factors over 72% when illuminated with a 1 sun AM0 spectrum. Optical absorption measurements in conjunction with EQE measurements indicate an internal quantum efficiency greater than 90% for the InGaN absorbing layer. By adjusting the thickness of the top p-type GaN window contact layer, it is shown that the short-wavelength (<365 nm) quantum efficiency is limited by the minority carrier diffusion length in highly Mg-doped p-GaN.

Development of highly efficient laser bars emitting at around 1060 nm for medical applications

NASA Astrophysics Data System (ADS)

Pietrzak, Agnieszka; Zorn, Martin; Meusel, Jens; Huelsewede, Ralf; Sebastian, Juergen

2018-02-01

An overview is presented on the recent progress in the development of high power laser bars at wavelengths around 1060nm. The development is focused on highly efficient and reliable laser performance under pulsed operation for medical applications. The epitaxial structure and lateral layout of the laser bars were tailored to meet the application requirements. Reliable operation peak powers of 350W and 500W are demonstrated from laser bars with fill-factor FF=75% and resonator lengths 1.5mm and 2.0mm, respectively. Moreover, 60W at current 65A with lifetime <10.000h are presented. The power scaling with fill-factor enables a cost reduction ($/W) up to 35%.

Charge tuning of nonresonant magnetoexciton phonon interactions in graphene.

PubMed

Rémi, Sebastian; Goldberg, Bennett B; Swan, Anna K

2014-02-07

Far from resonance, the coupling of the G-band phonon to magnetoexcitons in single layer graphene displays kinks and splittings versus filling factor that are well described by Pauli blocking and unblocking of inter- and intra-Landau level transitions. We explore the nonresonant electron-phonon coupling by high-magnetic field Raman scattering while electrostatic tuning of the carrier density controls the filling factor. We show qualitative and quantitative agreement between spectra and a linearized model of electron-phonon interactions in magnetic fields. The splitting is caused by dichroism of left- and right-handed circular polarized light due to lifting of the G-band phonon degeneracy, and the piecewise linear slopes are caused by the linear occupancy of sequential Landau levels versus ν.

Modifiable Risk Factors in Primary Joint Arthroplasty Increase 90-Day Cost of Care.

PubMed

Schroer, William C; Diesfeld, Paul J; LeMarr, Angela R; Morton, Diane J; Reedy, Mary E

2018-04-19

Risk factors in demographics and health status have been identified that increase the risk of complications after joint arthroplasty, necessitating additional care and incurring additional charges. The purpose of this study was to identify the number of patients in a hospital network database who had one or more predefined modifiable risk factors and determine their impact on average length of stay, need for additional care during the 90-day postoperative period, and the 90-day charges for care. An electronic hospital record query of 6968 lower extremity joint arthroplasty procedures under Diagnosis-Related Group 469/470 performed in 2014-2015 was reviewed, and total 90-day charges were calculated. The case mean was compared to charges for patients with modifiable risk factors: anemia (Hgb < 10 g/dL), malnutrition (albumin < 3.4 g/dL), obesity (body mass index > 45 kg/m 2 ), uncontrolled diabetes (random glucose >180 mg/dL or A1C > 8), narcotic use (prescription filled), and tobacco use (documented within 30 days before surgery). Length of stay, emergency room visits, and hospital readmission were compared. Mean 90-day charges for Diagnosis-Related Group 469/470 were $36,647. Risk factors were associated with a significant increase in 90-day charges: anemia (+$ 15,869/126 patients), malnutrition (+$9270/592), obesity (+$2048/445), diabetes (+$5074/291), narcotic use (+$1801/1943), and tobacco use (+$2034/1882). Intensive care unit admission rate, emergency department visits, and hospital readmission were significantly increased for patients with each risk factor. Length of stay was higher in patients with anemia, malnutrition, diabetes, and tobacco use. When separated by elective vs fracture admission, 90-day charges were significantly higher for each risk factor. Medical strategies to optimize patients before joint arthroplasty are warranted to improve postoperative outcomes. Copyright © 2018 Elsevier Inc. All rights reserved.

A comparison of glass cermet cement and amalgam restorations in primary molars.

PubMed

Hickel, R; Voss, A

1990-01-01

The aim of this clinical study was to compare the efficacy of GCC with amalgam as a filling material in primary molars. Two hundred fifteen restorations were placed in the first and second primary molars of seventy-four patients, ranging in age from four to ten years. The overall failure rate of amalgam is lower than that of GCC, but not significantly different. In older children, amalgam has greater advantages. An advantage of GCC is the short time required to fill the cavity. This might be an important factor in young and/or difficult children. In these cases amalgam cannot be placed under optimal conditions and, therefore, the results are less satisfactory. GCC is a viable alternative filling material.

Material limitations on the detection limit in refractometry.

PubMed

Skafte-Pedersen, Peder; Nunes, Pedro S; Xiao, Sanshui; Mortensen, Niels Asger

2009-01-01

We discuss the detection limit for refractometric sensors relying on high-Q optical cavities and show that the ultimate classical detection limit is given by min {Δn} ≳ η, with n + iη being the complex refractive index of the material under refractometric investigation. Taking finite Q factors and filling fractions into account, the detection limit declines. As an example we discuss the fundamental limits of silicon-based high-Q resonators, such as photonic crystal resonators, for sensing in a bio-liquid environment, such as a water buffer. In the transparency window (λ ≳ 1100 nm) of silicon the detection limit becomes almost independent on the filling fraction, while in the visible, the detection limit depends strongly on the filling fraction because the silicon absorbs strongly.

Preliminary Finnish Measures of Eating Competence Suggest Association with Health-Promoting Eating Patterns and Related Psychobehavioral Factors in 10–17 Year Old Adolescents

PubMed Central

Tanja, Tilles-Tirkkonen; Outi, Nuutinen; Sakari, Suominen; Jarmo, Liukkonen; Kaisa, Poutanen; Leila, Karhunen

2015-01-01

Eating competence is an attitudinal and behavioral concept, based on The Satter Eating Competence Model. In adults, it has been shown to be associated with a higher quality of diet. Eating competence or its association with the quality of diet has not been studied in adolescents. The aim of the current study was to explore the utility of using a preliminary Finnish translation of the ecSI 2.0 for evaluating presumed eating competence and its association with food selection, meal patterns and related psychobehavioral factors in 10–17 year old adolescents. Altogether 976 10–17 years old Finnish adolescents filled in the study questionnaire. When exploring the construct validity of ecSI 2.0, the confirmatory factor analysis (CFA) indicated acceptable model fit and all four components of the ecSI 2.0 (eating attitudes, food acceptance, internal regulation of food intake, management of eating context) correlated with each other and were internally consistent. Over half (58%) of the adolescents scored 32 or higher and were thus classified as presumably eating competent (pEC). Eating competence was associated with greater meal frequency, more frequent consumption of vegetables and fruits, and more health-promoting family eating patterns. In addition the pEC, adolescents more often perceived their body size as appropriate, had less often tried to lose weight and had a higher self-esteem and a stronger sense of coherence than the not pEC ones. Family eating patterns and self-esteem were the main underlying factors of eating competence. In conclusion, this preliminary study suggests eating competence could be a useful concept to characterize eating patterns and related behaviors and attitudes in adolescents. However, these preliminary findings need to be confirmed in further studies with an instrument fully validated for this age group. PMID:26007335

Preliminary Finnish measures of eating competence suggest association with health-promoting eating patterns and related psychobehavioral factors in 10-17 year old adolescents.

PubMed

Tanja, Tilles-Tirkkonen; Outi, Nuutinen; Sakari, Suominen; Jarmo, Liukkonen; Kaisa, Poutanen; Leila, Karhunen

2015-05-21

Eating competence is an attitudinal and behavioral concept, based on The Satter Eating Competence Model. In adults, it has been shown to be associated with a higher quality of diet. Eating competence or its association with the quality of diet has not been studied in adolescents. The aim of the current study was to explore the utility of using a preliminary Finnish translation of the ecSI 2.0 for evaluating presumed eating competence and its association with food selection, meal patterns and related psychobehavioral factors in 10-17 year old adolescents. Altogether 976 10-17 years old Finnish adolescents filled in the study questionnaire. When exploring the construct validity of ecSI 2.0, the confirmatory factor analysis (CFA) indicated acceptable model fit and all four components of the ecSI 2.0 (eating attitudes, food acceptance, internal regulation of food intake, management of eating context) correlated with each other and were internally consistent. Over half (58%) of the adolescents scored 32 or higher and were thus classified as presumably eating competent (pEC). Eating competence was associated with greater meal frequency, more frequent consumption of vegetables and fruits, and more health-promoting family eating patterns. In addition the pEC, adolescents more often perceived their body size as appropriate, had less often tried to lose weight and had a higher self-esteem and a stronger sense of coherence than the not pEC ones. Family eating patterns and self-esteem were the main underlying factors of eating competence. In conclusion, this preliminary study suggests eating competence could be a useful concept to characterize eating patterns and related behaviors and attitudes in adolescents. However, these preliminary findings need to be confirmed in further studies with an instrument fully validated for this age group.

Factors affecting HPV vaccine acceptance in west Austria: Do we need to revise the current immunization scheme?

PubMed

Borena, Wegene; Luckner-Hornischer, Anita; Katzgraber, Franz; Holm-von Laer, Dorothee

2016-12-01

Austria introduced a school-based gender-neutral human papillomavirus (HPV) immunization program in February 2014. In order to assure high coverage, factors influencing acceptance of the vaccine need to be identified. In this study we aim to assess parents' attitude and related socio-demographic factors in relation to the newly implemented gender-neutral, school-based HPV Immunization program. Parents of 4th grade school children in 20 randomly selected primary schools were asked to fill out questionnaires on socio-demographic factors and on the level of information and attitude towards HPV infection and HPV vaccine. A total of 439 parents with 449 vaccine eligible children participated in the study. Fifty nine percent of vaccine eligible girls and 51.8% of eligible boys received the first dose of the vaccine. Fear of side effects and child being too young for the vaccine were the most commonly cited reasons by parents electing not to let child receive the vaccine. Children who had received other school-based vaccines have more than fifteen times higher probability of receiving HPV vaccine. To have received HPV-related information from physicians positively influenced vaccine acceptance (OR (95% CI)=1.60 (1.06-2.43)). Higher paternal (fathers') educational status significantly increased the chances of a male child to be HPV vaccinated (OR (95% CI)=2.45 (1.29-4.78)). Despite the efforts to provide HPV vaccine free-of-costs and as a school-based program, the study found that a significant proportion of vaccine eligible children failed to receive the vaccine. Involvement front line physicians and men with higher educational status may be utilised by public health policy makers in the effort to increase awareness. For a better acceptability of the vaccine, there is a need to consider lifting the age of "eligibility" for the school-based vaccination program. Copyright © 2016 The Authors. Published by Elsevier B.V. All rights reserved.

Microwave response of hole and patch arrays

NASA Astrophysics Data System (ADS)

Taylor, Melita C.; Edmunds, James D.; Hendry, Euan; Hibbins, Alastair P.; Sambles, J. Roy

2010-10-01

The electromagnetic response of two-dimensional square arrays of perfectly conducting square patches, and their complementary structures, is modeled utilizing a modal matching technique and employing Babinet’s principle. This method allows for the introduction of progressively higher diffracted orders and waveguide modes to be included in the calculation, hence aiding understanding of the underlying causal mechanism for the observed response. At frequencies close to, but below, the onset of diffraction, a near-complete reflection condition is predicted, even for low filling fractions: conversely, for high filling fractions a near-complete transmission condition results. These resonance phenomena are associated with evanescent diffraction, which is sufficiently strong to reverse the step change in transmission upon establishment of electrical continuity; i.e., the connected structure demonstrates increased transmission with increasing filling fraction.

Health Risk Assessment of Lead Ingestion Exposure by Particle Sizes in Crumb Rubber on Artificial Turf Considering Bioavailability

PubMed Central

Kim, Sunduk; Yang, Ji-Yeon; Kim, Ho-Hyun; Yeo, In-Young; Shin, Dong-Chun

2012-01-01

Objectives The purpose of this study was to assess the risk of ingestion exposure of lead by particle sizes of crumb rubber in artificial turf filling material with consideration of bioavailability. Methods This study estimated the ingestion exposure by particle sizes (more than 250 um or less than 250 um) focusing on recyclable ethylene propylene diene monomer crumb rubber being used as artificial turf filling. Analysis on crumb rubber was conducted using body ingestion exposure estimate method in which total content test method, acid extraction method and digestion extraction method are reflected. Bioavailability which is a calibrating factor was reflected in ingestion exposure estimate method and applied in exposure assessment and risk assessment. Two methods using acid extraction and digestion extraction concentration were compared and evaluated. Results As a result of the ingestion exposure of crumb rubber material, the average lead exposure amount to the digestion extraction result among crumb rubber was calculated to be 1.56×10-4 mg/kg-day for low grade elementary school students and 4.87×10-5 mg/kg-day for middle and high school students in 250 um or less particle size, and that to the acid extraction result was higher than the digestion extraction result. Results of digestion extraction and acid extraction showed that the hazard quotient was estimated by about over 2 times more in particle size of lower than 250 um than in higher than 250 um. There was a case of an elementary school student in which the hazard quotient exceeded 0.1. Conclusions Results of this study confirm that the exposure of lead ingestion and risk level increases as the particle size of crumb rubber gets smaller. PMID:22355803

Clarifying the Impact of Untreated and Treated Dental Caries on Oral Health-Related Quality of Life among Adolescents.

PubMed

Feldens, Carlos Alberto; Ardenghi, Thiago Machado; Dos Santos Dullius, Angela Isabel; Vargas-Ferreira, Fabiana; Hernandez, Pedro Antonio González; Kramer, Paulo Floriani

2016-01-01

The aim of the present study was to investigate the effect of dental caries experience and the components of the decayed, missing and filled teeth (DMFT) index on oral health-related quality of life (OHRQoL) among adolescents in southern Brazil. A cross-sectional study was conducted with 509 adolescents aged 11-14 years enrolled at public schools in the municipality of Osório (southern Brazil). A calibrated examiner performed the clinical examination for caries (World Health Organization: DMFT index), malocclusion (Dental Aesthetic Index) and traumatic dental injuries [Andreasen et al., 2007]. The participants answered the Brazilian version of the Child Perceptions Questionnaire (CPQ11-14) - Impact Short Form, and their parents/guardians answered a structured questionnaire addressing demographic and socioeconomic characteristics. Data analysis involved Poisson regression with robust variance, with the calculation of rate ratios adjusted for potential confounding variables. High severity of dental caries experience exerted a significant impact on OHRQoL, even after controlling for socioeconomic and clinical factors (rate ratio 1.30; 95% confidence interval, CI 1.12-1.51). All OHRQoL domains were affected by untreated dental caries. The multivariate analysis demonstrated that the CPQ11-14 scores were 33% higher among adolescents with untreated caries (rate ratio 1.33; 95% CI 1.17-1.50) and 24% higher among those with missing teeth (rate ratio 1.24; 95% CI 1.06-1.47). No difference in OHRQoL was found between adolescents with filled teeth and those without dental caries. In conclusion, dental caries experience, untreated dental caries and missing teeth exerted a negative impact on OHRQoL among the adolescents. © 2016 S. Karger AG, Basel.

Fully relayed regenerative amplifier

DOEpatents

Glass, Alexander J.

1981-01-01

A regenerative laser apparatus and method using the optical relay concept to maintain high fill factors, to suppress diffraction effects, and to minimize phase distortions in a regenerative amplifier.

Modeling invasive breast cancer: growth factors propel progression of HER2-positive premalignant lesions

PubMed Central

Pradeep, C-R; Zeisel, A; Köstler, WJ; Lauriola, M; Jacob-Hirsch, J; Haibe-Kains, B; Amariglio, N; Ben-Chetrit, N; Emde, A; Solomonov, I; Neufeld, G; Piccart, M; Sagi, I; Sotiriou, C; Rechavi, G; Domany, E; Desmedt, C; Yarden, Y

2013-01-01

The HER2/neu oncogene encodes a receptor-like tyrosine kinase whose overexpression in breast cancer predicts poor prognosis and resistance to conventional therapies. However, the mechanisms underlying aggressiveness of HER2 (human epidermal growth factor receptor 2)-overexpressing tumors remain incompletely understood. Because it assists epidermal growth factor (EGF) and neuregulin receptors, we overexpressed HER2 in MCF10A mammary cells and applied growth factors. HER2-overexpressing cells grown in extracellular matrix formed filled spheroids, which protruded outgrowths upon growth factor stimulation. Our transcriptome analyses imply a two-hit model for invasive growth: HER2-induced proliferation and evasion from anoikis generate filled structures, which are morphologically and transcriptionally analogous to preinvasive patients’ lesions. In the second hit, EGF escalates signaling and transcriptional responses leading to invasive growth. Consistent with clinical relevance, a gene expression signature based on the HER2/EGF-activated transcriptional program can predict poorer prognosis of a subgroup of HER2-overexpressing patients. In conclusion, the integration of a three-dimensional cellular model and clinical data attributes progression of HER2-overexpressing lesions to EGF-like growth factors acting in the context of the tumor's microenvironment. PMID:22139081

Water adsorption isotherms on porous onionlike carbonaceous particles. Simulations with the grand canonical Monte Carlo method

NASA Astrophysics Data System (ADS)

Hantal, György; Picaud, Sylvain; Hoang, Paul N. M.; Voloshin, Vladimir P.; Medvedev, Nikolai N.; Jedlovszky, Pál

2010-10-01

The grand canonical Monte Carlo method is used to simulate the adsorption isotherms of water molecules on different types of model soot particles. These soot models are constructed by first removing atoms from onion-fullerene structures in order to create randomly distributed pores inside the soot, and then performing molecular dynamics simulations, based on the reactive adaptive intermolecular reactive empirical bond order (AIREBO) description of the interaction between carbon atoms, to optimize the resulting structures. The obtained results clearly show that the main driving force of water adsorption on soot is the possibility of the formation of new water-water hydrogen bonds with the already adsorbed water molecules. The shape of the calculated water adsorption isotherms at 298 K strongly depends on the possible confinement of the water molecules in pores of the carbonaceous structure. We found that there are two important factors influencing the adsorption ability of soot. The first of these factors, dominating at low pressures, is the ability of the soot of accommodating the first adsorbed water molecules at strongly hydrophilic sites. The second factor concerns the size and shape of the pores, which should be such that the hydrogen bonding network of the water molecules filling them should be optimal. This second factor determines the adsorption properties at higher pressures.

Seroprevalence and risk factors associated with bovine viral diarrhea virus (BVDV) infection in non-vaccinated dairy and dual purpose cattle herds in Ecuador.

PubMed

Saa, Luis Rodrigo; Perea, Anselmo; García-Bocanegra, Ignacio; Arenas, Antonio José; Jara, Diego Vinicio; Ramos, Raul; Carbonero, Alfonso

2012-03-01

A cross-sectional study was carried out to determine the seroprevalence and risk factors associated with Bovine viral diarrhea virus (BVDV) infection in non-vaccinated dairy and dual-purpose cattle herds from Ecuador. A total of 2,367 serum samples from 346 herds were collected from June 2008 through February 2009. A questionnaire, which included variables related to cattle, health, management measures, and the environment, was filled out in each herd. A commercial indirect enzyme-linked immunosorbent assay test was used to determine the seropositivity. A logistic regression model was used to determine risk factors at herd level. The individual seroprevalence for BVDV in non-vaccinated herds in Ecuador was 36.2% (857/2,367; CI(95%), 34.3-38.1%). The herd prevalence was 74% (256/346; CI(95%), 69.4-78.6%) and the intra-herd prevalence ranged between 11.1% and 100% (mean = 51.6%). The logistic regression model showed that the density of cattle farms in the area (more than 70%; OR, 1.94; CI(95%), 1.21-3.2) and the altitude (higher than 2,338 m above sea level; 2.33; CI(95%), 1.4-3.9) are potential risk factors associated with BVDV infection.

Electrophysiological and mechanical effects of substance P and acetylcholine on rabbit aorta.

PubMed Central

Bény, J L; Brunet, P C

1988-01-01

1. The mechanical and electrical properties of smooth muscle cells of the rabbit aorta were recorded simultaneously using respectively a force transducer and a 3 M-KCl-filled glass microelectrode. 2. Acetylcholine had two effects depending on concentration. At low concentration, it caused a persistent endothelium-dependent relaxation and hyperpolarization. At higher concentrations the acetylcholine endothelium-dependent relaxation summed with an endothelium-independent contraction. 3. Substance P caused a transient endothelium-dependent relaxation and hyperpolarization. 4. Acetylcholine and substance P depolarized and contracted de-endothelialized smooth muscle. When the de-endothelialized strip was pre-contracted by noradrenaline, acetylcholine depolarized the muscle but substance P did not. 5. In a 'cascade' experiment, the perfusate from an upstream intact aorta passed over a downstream de-endothelialized strip. Acetylcholine and substance P relaxed the downstream strip showing that they released an endothelial humoral factor which relaxes smooth muscle. 6. The results suggest a constant release of a factor from the endothelial cells which hyperpolarizes the smooth muscle cells in the media. Activation of acetylcholine and substance P receptors on the endothelium accelerates the release of this factor and causes vasodilatation. PMID:2455799

Propulsion and Power Rapid Response Research and Development (R&D) Support. Delivery Order 0011: Advanced Propulsion Fuels Research and Development-Subtask: Framework and Guidance for Estimating Greenhouse Gas Footprints of Aviation Fuels

DTIC Science & Technology

2009-04-01

Uncertainties, Gaps , and Issues for the Use of GWP to Examine Emissions From Aviation That Impact Global Climate Change. (Wuebbles, Yang and Herman 2008...selecting time periods and spatial scales for data gathering, strategies for filling data gaps , and computational considerations for managing the...Fuels Assumptions, methodological choices, strategies for filling data gaps , and other factors throughout the life cycle substantially influence the

An Analytical Solution and Numerical Modeling Study of Gas Hydrate Saturation Effects on Porosity and Permeability of Porous Media

NASA Astrophysics Data System (ADS)

Zerpa, L.; Gao, F.; Wang, S.

2017-12-01

There are two major types of natural gas hydrate distributions in porous media: pore filling and contact cementing. The difference between these two distribution types is related to hydrate nucleation and growth processes. In the pore filling distribution, hydrate nucleates from a gas-dissolved aqueous phase at the grain boundary and grows away from grain contacts and surfaces into the pore space. In the contact cementing distribution, hydrate nucleates and grows at the gas-water interface and at intergranular contacts. Previous attempts to correlate changes on porosity and permeability during hydrate formation/dissociation were based on the length difference between the pore body and pore throat, and only considered contact cementing hydrate distribution. This work consists of a study of mathematical models of permeability and porosity as a function of gas hydrate saturation during formation and dissociation of gas hydrates in porous media. In this work, first we derive the permeability equation for the pore filling hydrate deposition as a function of hydrate saturation. Then, a more comprehensive model considering both types of gas hydrate deposition is developed to represent changes in permeability and porosity during hydrate formation and dissociation. This resulted in a model that combines pore filling and contact cementing deposition types in the same reservoir. Finally, the TOUGH+Hydrate numerical reservoir simulator was modified to include these models to analyze the response of production and saturation during a depressurization process, considering different combinations of pore filling and contact cementing hydrate distributions. The empirical exponent used in the permeability adjustment factor model influences both production profile and saturation results. This empirical factor describes the permeability dependence to changes in porosity caused by solid phase formation in the porous medium. The use of the permeability exponent decreases the permeability of the system for a given hydrate saturation, which affects the hydraulic performance of the system. However, from published experimental work, there is only a rough estimation of this permeability exponent. This factor could be represented with an empirical equation if more laboratory and field data becomes available.

Shear bond strength of bulk-fill and nano-restorative materials to dentin.

PubMed

Colak, Hakan; Ercan, Ertugrul; Hamidi, Mehmet Mustafa

2016-01-01

Bulk-fill composite materials are being developed for preparation depths of up to 4 mm in an effort to simplify and improve the placement of direct composite posterior restorations. The aim of our study was to compare shear-bond strength of bulk-fill and conventional posterior composite resins. In this study, 60 caries free extracted human molars were used and sectioned parallel to occlusal surface to expose midcoronal dentin. The specimens were randomly divided into four groups. Total-etch dentine bonding system (Adper Scotchbond 1XT, 3M ESPE) was applied to dentin surface in all the groups to reduce variability in results. Then, dentine surfaces covered by following materials. Group I: SonicFill Bulk-Fill, Group II: Tetric EvoCeram (TBF), Group III: Herculite XRV Ultra, and Group IV: TBF Bulk-Fill, 2 mm × 3 mm cylindrical restorations were prepared by using application apparatus. Shear bond testing was measured by using a universal testing machine. Kruskal-Wallis and Mann-Whitney U-tests were performed to evaluate the data. The highest value was observed in Group III (14.42 ± 4.34) and the lowest value was observed in Group IV (11.16 ± 2.76) and there is a statistically significant difference between these groups (P = 0.046). However, there is no statistically significant difference between the values of other groups. In this study, Group III was showed higher strength values. There is a need for future studies about long-term bond strength and clinical success of these adhesive and bulk-fill systems.

[Effects of shading at different phases of grain-filling on wheat grain protein components contents and processing quality].

PubMed

Shi, Yu; Chen, Mao-xue; Yu, Zhen-wen; Xu, Zhen-zhu

2011-10-01

Taking three wheat cultivars Jimai 20 (strong gluten), Taishan 23 (medium gluten), and Ningmai 9 (weak gluten) as test materials, a field experiment was conducted to examine the effects of shading at different phases of grain-filling on the grain protein components contents and processing quality. Four treatments were installed, i. e., no shading (S0), shading at early grain-filling phase (from 0 day after anthesis (DAA) to 11 DAA; S1), shading at medium grain-filling phase (from 12 DAA to 23 DAA; S2), and shading at late grain-filling phase (from 24 DAA to 35 DAA; S3). No significant differences were observed in the grain albumin+globulin contents of the three cultivars among the four treatments. Shading increased the grain HMW-GS, LMW-GS, gluten, glutenin, and total protein contents of Jimai 20 and Taishan 23 significantly, and the increments were higher in treatment S2 than in other shading treatments. Treatments S2 and S3 increased the grain protein components contents of Ningmai 9 significantly. Comparing with the control, shading decreased the grain yield significantly, but increased the dough development time, dough stability time, and sedimentation volume, especially for treatment S2, which suggested that the wheat grain quality had a close relationship with the light intensity at medium phase of grain-filling. Overall, the regulation effect of shading at grain-filling stage on the wheat grain yield, grain protein components contents, and indices values of grain processing quality for the test cultivars was in the order of Jimai 20 > Taishan 23 > Ningmai 9.

On the effectiveness of incorporating shear thickening fluid with fumed silica particles in hip protectors

NASA Astrophysics Data System (ADS)

Haris, A.; Goh, B. W. Y.; Tay, T. E.; Lee, H. P.; Rammohan, A. V.; Tan, V. B. C.

2018-01-01

The objective of this research is to develop a smart hip protector by incorporating shear thickening fluid (STF) into conventional foam hip protectors. The shear thickening properties of fumed silica particles dispersed in liquid polyethylene glycol (PEG) were determined from rheological tests. Dynamic drop tests, using a 4 kg drop platen at 0.5 m drop height, were conducted to study how STF improves energy absorption as compared to unfilled foam and PEG filled foam. The results show that PEG filled foam reduces the mean peak force transmitted by a further 55% and mean peak displacement by 32.5% as compared to the unfilled foam; the STF filled foam further reduces mean peak force and displacement by 15% and 41% respectively when compared to the PEG filled foam. At a displacement of 22 mm, the STF filled foam absorbs 7.4 times more energy than the PEG filled foam. The results of varying the drop mass and drop height show that the energy absorbed per unit displacement for STF filled foam is always higher than that of PEG filled foam. Finally, the effectiveness of a prototype of hip protector made from 15 mm thick STF filled foam in preventing hip fractures was studied under two different loading conditions: distributed load (plate drop test) and concentrated load (ball drop test). The results of the plate and ball drop tests show that among all hip protectors tested in this study, only the prototype can reduce the mean peak impact force to be lower than the force required to fracture a hip bone (3.1 kN) regardless of the type of loading. Moreover, the peak force of the prototype is about half of this value, suggesting thinner prototype could have been used instead. These findings show that STF is effective in improving the performance of hip protectors.

The short-term effects of television advertisements of cariogenic foods on children's dietary choices.

PubMed

Gatou, Tarsitsa; Mamai-Homata, Eleni; Koletsi-Kounari, Haroula; Polychronopoulou, Argy

2016-10-01

To investigate the short-term influence of the advertising of cariogenic foods on children's dietary preferences, and the possible moderating effect of several factors on this influence. One-hundred and eighty-three children, 11-12 years of age, were exposed to advertisements showing sugary food and non-food items, in a within-subject counterbalanced design. Their preferences for unhealthy and healthy foods, and their ability to recall or recognise the advertisements, were measured following both sessions. Information on their dietary habits, leisure activities and sociodemographic details were obtained through a questionnaire completed by their parents. Their decayed, missing and filled teeth (DMFT) index, body weight and height were also recorded. A generalised linear mixed model was used to examine the differences in food preferences between experimental conditions, and the associations between children's preferences and the other factors assessed. Exposure to food advertisements significantly decreased the selection of healthy foods. Children with a higher DMFT index chose a higher percentage of unhealthy foods, and children who spent more time watching television chose an increased number of healthy foods, after their exposure to food advertisements. Regardless of condition, girls selected fewer foods than boys. Children with a higher DMFT index selected more unhealthy foods than children with a lower DMFT index. Obese children chose an increased number of healthy foods than those who were overweight and normal weight. Food advertisements can divert, for a short time, children's preference over healthy food choices, and could lead to changes in their eating habits, which may put them at higher risk of dental diseases and obesity. © 2016 FDI World Dental Federation.

Infected nonunion of tibia

PubMed Central

Chaudhary, Milind Madhav

2017-01-01

Infected nonunions of tibia pose many challenges to the treating surgeon and the patient. Challenges include recalcitrant infection, complex deformities, sclerotic bone ends, large bone gaps, shortening, and joint stiffness. They are easy to diagnose and difficult to treat. The ASAMI classification helps decide treatment. The nonunion severity score proposed by Calori measures many parameters to give a prognosis. The infection severity score uses simple clinical signs to grade severity of infection. This determines number of surgeries and allows choice of hardware, either external or internal for definitive treatment. Co-morbid factors such as smoking, diabetes, nonsteroidal anti-inflammatory drug use, and hypovitaminosis D influence the choice and duration of treatment. Thorough debridement is the mainstay of treatment. Removal of all necrotic bone and soft tissue is needed. Care is exercised in shaping bone ends. Internal fixation can help achieve union if infection was mild. Severe infections need external fixation use in a second stage. Compression at nonunion site achieves union. It can be combined with a corticotomy lengthening at a distant site for equalization. Soft tissue deficit has to be covered by flaps, either local or microvascular. Bone gaps are best filled with the reliable technique of bone transport. Regenerate bone may be formed proximally, distally, or at both sites. Acute compression can fill bone gaps and may need a fibular resection. Gradual reduction of bone gap happens with bone transport, without need for fibulectomy. When bone ends dock, union may be achieved by vertical or horizontal compression. Biological stimulus from iliac crest bone grafts, bone marrow aspirate injections, and platelet concentrates hasten union. Bone graft substitutes add volume to graft and help fill defects. Addition of rh-BMP-7 may help in healing albeit at a much higher cost. Regeneration may need stimulation and augmentation. Induced membrane technique is an alternative to bone transport to fill gaps. It needs large amounts of bone graft from iliac crest or femoral canal. This is an expensive method physiologically and economically. Infection can resorb the graft and cause failure of treatment. It can be done in select cases after thorough eradication of infection. Patience and perseverance are needed for successful resolution of infection and achieving union. PMID:28566776

Dental metal-induced innate reactivity in keratinocytes.

PubMed

Mortazavi, S M J; Mortazavi, Ghazal; Paknahad, Maryam

2016-06-01

In their paper that is published in Toxicology in Vitro, Rachmawati et al. have recently claimed that in spite of the growing concern about the safety of amalgam, negative reports about the health effects of dental amalgam are still scarce or controversial. Substantial evidence indicates that mercury release from dental amalgam fillings may adversely affect human health. Over the past years, we have shown that exposure to electromagnetic fields (EMFs) can increase the release of mercury from dental amalgam fillings. It is worth mentioning that the results of investigations on the microleakage of amalgam fillings following MRI have confirmed our results. Furthermore, exposure to X-rays as a part of the electromagnetic spectrum has also been linked to increased mercury release from dental amalgam fillings. Considering the explosive rise in human exposure to electromagnetic fields, the role of human exposure to EMF as a key factor in increasing the release of mercury from dental amalgam restorations cannot be simply ignored. Copyright © 2016 Elsevier B.V. All rights reserved.

Blast Wave Experiments at Z

DTIC Science & Technology

2007-06-01

radiation flows upward, it passes though a 1.7-mm high, tapered, 25-μm thick gold wall cone that is filled 20 ± 3 mg/cm3 silica aerogel (SiO2). Above...this cone is a 20 ± 3 mg/cm3 silica aerogel filled, 1-mm high, 2.4-mm inner diameter, 25-μm thick gold wall cylinder. On the cylinder rests a 4-mm...diameter gold platform that supports a higher density (40-60 mg/cm3) silica aerogel . This aerogel is the region where the blast wave forms after

Extension and Density of Root Fillings and Post-operative Apical Radiolucencies in the Veterans Affairs Dental Longitudinal Study

PubMed Central

Zhong, Yan; Chasen, Joel; Yamanaka, Ryan; Garcia, Raul; Kaye, Elizabeth Krall; Kaufman, Jay S; Cai, Jianwen; Wilcosky, Tim; Trope, Martin; Caplan, Daniel J

2008-01-01

We evaluated the association between radiographically-assessed extension and density of root canal fillings and post-operative apical radiolucencies (AR) using data from 288 participants in the Veterans Affairs Dental Longitudinal Study. Study subjects were not VA patients; all received their medical and dental care in the private sector. Generalized Estimating Equations were used to account for multiple teeth within subjects and to control for covariates of interest. Defective root filling density was associated with increased odds of post-operative AR among teeth with no pre-operative AR (Odds Ratio=3.0, 95%CI=1.3–7.1), though pre-operative AR was the strongest risk factor for post-operative AR (Odds Ratio=29.2, 95%CI=13.6–63.0 among teeth with ideal density). Compared to well-extended root fillings, neither over- nor under-extended root fillings separately were related to post-operative AR, but when those two categories were collapsed into one “poorly-extended” category, poor extension was related to post-operative AR (Odds Ratio=1.8, 95%CI=1.1–3.2). PMID:18570982

Prevalence of apical periodontitis and endodontic treatment in a Kosovar adult population.

PubMed

Kamberi, Blerim; Hoxha, Veton; Stavileci, Miranda; Dragusha, Edmond; Kuçi, Astrit; Kqiku, Lumnije

2011-11-29

Despite numerous studies on the prevalence of apical periodontitis (AP) and endodontic treatment in diverse geographical populations, there are currently no data on the prevalence of these conditions in populations of adults native to Kosovo. Therefore, little is known about how widespread these conditions are, and whether there is any correlation between root canal treatment and AP. The purpose of our research was to address this anomaly by investigating AP and endodontic treatment in an adult Kosovar population based on radiographic examination. The sample used for this study consisted of randomly selected individuals referred to the University Dentistry Clinical Center of Kosovo in the years 2006-2007. Orthopantomographs of 193 patients were evaluated. The periapical status of all teeth (with the exception of third molars) was examined according to Ørstavik's Periapical Index. The quality of the root canal filling was rated as 'adequate' or 'inadequate' based on whether all canals were filled, the depth of fill relative to the radiographic apex and the quality of compaction (absence/presence of voids). Data were analyzed statistically using the Chi-square test and calculation of odds ratios. Out of 4131 examined teeth, the prevalence of apical periodontitis (AP) and endodontic treatment was 12.3% and 2.3%, respectively. Of 95 endodontically-treated teeth, 46.3% were associated with AP. The prevalence of AP increased with age. The prevalence in subjects aged over 60 years old (20.2%) was higher than in other age groups. A statistically significant difference was found for the frequency of endodontically-treated teeth associated with AP in the 40-49 year age group (P < 0.001). Of some concern was the discovery that only 30.5% of the endodontically-treated teeth examined met the criteria of an acceptable root canal filling. Inadequately root-filled teeth were associated with an increased AP risk. The prevalence of AP and the frequency of endodontically-treated teeth with AP in this Kosovar population are higher than those found in other countries. Inadequate root canal fillings were associated with an increased prevalence of AP.

Polymerization stress evolution of a bulk-fill flowable composite under different compliances.

PubMed

Guo, Yongwen; Landis, Forrest A; Wang, Zhengzhi; Bai, Ding; Jiang, Li; Chiang, Martin Y M

2016-04-01

To use a compliance-variable instrument to simultaneously measure and compare the polymerization stress (PS) evolution, degree of conversion (DC), and exotherm of a bulk-fill flowable composite to a packable composite. A bulk-fill flowable composite (Filtek Bulk-fill, FBF) and a conventional packable composite (Filtek Z250, Z250) purchased from 3M ESPE were investigated. The composites were studied using a cantilever-beam based instrument equipped with an in situ near infrared (NIR) spectrometer and a microprobe thermocouple. The measurements were carried out under various instrumental compliances (ranging from 0.3327μm/N to 12.3215μm/N) that are comparable to the compliances of clinically prepared tooth cavities. Correlations between the PS and temperature change as well as the DC were interpreted. The maximum PS of both composites at 10min after irradiation decreased with the increase in the compliance of the cantilever beam. The FBF composite generated a lower final stress than the Z250 sample under instrumental compliances less than ca. 4μm/N; however, both materials generated statistically similar PS values at higher compliances. The reaction exotherm and the DC of both materials were found to be independent of compliance. The DC of the FBF sample was slightly higher than that of the packable Z250 composite while the peak exotherm of FBF was almost double that of the Z250 composite. For FBF, a characteristic drop in the PS was observed during the early stage of polymerization for all compliances studied which was not observed in the Z250 sample. This drop was shown to relate to the greater exotherm of the less-filled FBF sample relative to the Z250 composite. While the composites with lower filler content (low viscosity) are generally considered to have lower PS than the conventional packable composites, a bulk-fill flowable composite was shown to produce lower PS under a lower compliance of constraint as would be experienced if the composite was used as the base material in clinical procedures. Published by Elsevier Ltd.

Preparing Special Education Higher Education Faculty: The Influences of Contemporary Education Issues and Policy Recommendations

ERIC Educational Resources Information Center

deBettencourt, Laurie U.; Hoover, John J.; Rude, Harvey A.; Taylor, Shanon S.

2016-01-01

There is a well-documented need for leadership personnel who are prepared at the doctoral level to fill special education faculty positions at institutions of higher education (IHEs) and train the next generation of teachers. The intersection of continued retirements of special education faculty, shortage of well-prepared special education faculty…

Student Leadership Characteristics Leading to Success in an Online Community College Program

ERIC Educational Resources Information Center

Waters, Elsa G.

2012-01-01

This study was an effort to fill a gap in the research about why there are higher drop-out rates for students in online classrooms than students in traditional classrooms. Educators and administrators at online higher education institutions need information with which to address drop-out rates because the decreased number of completed online…

Filling in the Blanks: How Information Can Affect Choice in Higher Education

ERIC Educational Resources Information Center

Kelly, Andrew P.; Schneider, Mark

2011-01-01

Spurred on by the Obama administration, and supported by the Bill and Melinda Gates Foundation and the Lumina Foundation, the United States has embarked on a "college completion agenda" to increase the number of American adults with postsecondary degrees. While the push to improve consumer information in the higher education market has gained…

Validity of a family-centered approach for assessing infants' social-emotional wellbeing and their developmental context: a prospective cohort study.

PubMed

Hielkema, Margriet; De Winter, Andrea F; Reijneveld, Sijmen A

2017-06-15

Family-centered care seems promising in preventive pediatrics, but evidence is lacking as to whether this type of care is also valid as a means to identify risks to infants' social-emotional development. We aimed to examine the validity of such a family-centered approach. We conducted a prospective cohort study. During routine well-child visits (2-15 months), Preventive Child Healthcare (PCH) professionals used a family-centered approach, assessing domains as parents' competence, role of the partner, social support, barriers within the care-giving context, and child's wellbeing for 2976 children as protective, indistinct or a risk. If, based on the overall assessment (the families were labeled as "cases", N = 87), an intervention was considered necessary, parents filled in validated questionnaires covering the aforementioned domains. These questionnaires served as gold standards. For each case, two controls, matched by child-age and gender, also filled in questionnaires (N = 172). We compared PCH professionals' assessments with the parent-reported gold standards. Moreover, we evaluated which domain mostly contributed to the overall assessment. Spearman's rank correlation coefficients between PCH professionals' assessments and gold standards were overall reasonable (Spearman's rho 0.17-0.39) except for the domain barriers within the care-giving context. Scores on gold standards were significantly higher when PCH assessments were rated as "at risk" (overall and per domain).We found reasonable to excellent agreement regarding the absence of risk factors (negative agreement rate: 0.40-0.98), but lower agreement regarding the presence of risk factors (positive agreement rate: 0.00-0.67). An "at risk" assessment for the domain Barriers or life events within the care-giving context contributed most to being overall at risk, i.e. a case, odds ratio 100.1, 95%-confidence interval: 22.6 - infinity. Findings partially support the convergent validity of a family-centered approach in well-child care to assess infants' social-emotional wellbeing and their developmental context. Agreement was reasonable to excellent regarding protective factors, but lower regarding risk factors. Netherlands Trialregister, NTR2681. Date of registration: 05-01-2011, URL: http://www.trialregister.nl/trialreg/admin/rctview.asp?TC=2681 .

External root resorption during orthodontic treatment in root-filled teeth and contralateral teeth with vital pulp: A clinical study of contributing factors.

PubMed

Lee, Yun Ju; Lee, Tae Yeon

2016-01-01

There is a lack of research to support the belief that root canal treatment can be considered for stopping or decreasing external apical root resorption (EARR). There is conflicting evidence as to whether root-filled teeth are more or less likely to experience EARR after orthodontic treatment. The purpose of this study was to compare the degree of EARR of root-filled teeth with that of contralateral teeth with vital pulp after fixed orthodontic treatment. The study sample consisted of 35 patients aged 25.23 ± 4.92 years who had at least 1 root-filled tooth before orthodontic treatment. Digital panoramic radiographs of each patient taken before and after orthodontic treatment were used to measure the EARR. The Student t test for matched pairs and the Pearson correlation analysis were applied. The mean EARR values were 0.22 (0.14, 0.35) for root-filled teeth and 0.87 (0.59, 1.31) for contralateral teeth with vital pulp, indicating significantly less EARR for root-filled teeth compared with the contralateral teeth with vital pulp after orthodontic treatment. EARR was influenced by the patient's age, treatment duration, treatment type, and periapical pathosis, but not by tooth type and sex. Root-filled teeth appear to be associated with significantly less EARR than are contralateral teeth with vital pulp. This study suggests that the possible complication of EARR in root-filled teeth may not be an important consideration in orthodontic treatment planning, and root canal treatment can be considered for stopping or decreasing EARR when severe EARR occurs during orthodontic treatment. Copyright © 2016 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

Impact of the quality of coronal restoration and root canal filling on the periapical health in adult syrian subpopulation

PubMed Central

Alafif, Hisham

2014-01-01

Background: The purpose of this study was to determine the status of periapical tissues of endodontically treated teeth according to coronal restorations and root canal fillings separately and in concomitant in adult Syrian subpopulation. Methods: 784 endodontically treated teeth from two hundred randomly selected Syrian adult patients were radiographically evaluated. According to predetermined criteria, the quality of coronal restorations and root canal filling of each tooth was scored as adequate or inadequate. The status of periapical tissues was also classified as healthy or diseased. Results were analyzed using Chi-squared test. Results: Adequate coronal restorations were determined in 58.54% of cases which was accompanied with less periapical pathosis than that in teeth with inadequate restorations (P < 0.01). 14% of teeth were restored by posts which showed no significant impact on the periapical tissues health. 18.5% of endodontic treatments were evaluated as adequate with less number of periapical radiolucencies than that of inadequate root canal fillings (P < 0.01). Absence of periapical pathosis was 96.6% in cases with both adequate coronal restorations and root canals fillings. The rate was 88.5% in cases with only adequate root canals fillings, and about 70% in cases with only adequate coronal restorations. When the treatment was inadequate in both coronal and root canals fillings, success rate was only observed in 48.8%. Conclusion: The most important factor with regard to the periradicular tissue health is the quality of root canal filling without neglecting the influence of coronal restoration (regardless of its type). There is a high prevalence rate of periapical pathosis in Syrian subpopulation due to poor dental practice. PMID:25565729

Angle-resolved reflection spectroscopy of high-quality PMMA opal crystal

NASA Astrophysics Data System (ADS)

Nemtsev, Ivan V.; Tambasov, Igor A.; Ivanenko, Alexander A.; Zyryanov, Victor Ya.

2018-02-01

PMMA opal crystal was prepared by a simple hybrid method, which includes sedimentation, meniscus formation and evaporation. We investigated three surfaces of this crystal by angle-resolved reflective light spectroscopy and SEM study. The angle-resolved reflective measurements were carried out in the 400-1100 nm range. We have determined the high-quality ordered surface of the crystal region. Narrow particle size distribution of the surface has been revealed. The average particle diameter obtained with SEM was nearly 361 nm. The most interesting result was that reflectivity of the surface turned out up to 98% at normal light incidence. Using a fit of dependences of the maximum reflectivity wavelength from an angle based on the Bragg-Snell law, the wavelength of maximum 0° reflectivity, the particle diameter and the fill factor have been determined. For the best surface maximum reflectivity wavelength of a 0° angle was estimated to be 869 nm. The particle diameter and fill factor were calculated as 372 nm and 0.8715, respectively. The diameter obtained by fitting is in excellent agreement with the particle diameter obtained with SEM. The reflectivity maximum is assumed to increase significantly when increasing the fill factor. We believe that using our simple approach to manufacture PMMA opal crystals will significantly increase the fabrication of high-quality photonic crystal templates and thin films.

Unconventional imaging with contained granular media

NASA Astrophysics Data System (ADS)

Quadrelli, Marco B.; Basinger, Scott; Sidick, Erkin

2017-09-01

Typically, the cost of a space-borne imaging system is driven by the size and mass of the primary aperture. The solution that we propose uses a method to construct an imaging system in space in which the nonlinear optical properties of a cloud of micron-sized particles, shaped into a specific surface by electromagnetic means, and allows one to form a very large and lightweight aperture of an optical system, hence reducing overall mass and cost. Recent work at JPL has investigated the feasibility of a granular imaging system, concluding that such a system could be built and controlled in orbit. We conducted experiments and simulation of the optical response of a granular lens. In all cases, the optical response, measured by the Modulation Transfer Function, of hexagonal reflectors was closely comparable to that of a conventional spherical mirror. We conducted some further analyses by evaluating the sensitivity to fill factor and grain shape, and found a marked sensitivity to fill factor but no sensitivity to grain shape. We have also found that at fill factors as low as 30%, the reflection from a granular lens is still excellent. Furthermore, we replaced the monolithic primary mirror in an existing integrated model of an optical system (WFIRST Coronagraph) with a granular lens, and found that the granular lens that can be useful for exoplanet detection provides excellent contrast levels. We will present our testbed and simulation results in this paper.

Computer analysis of microcrystalline silicon hetero-junction solar cell with lumerical FDTD/DEVICE

NASA Astrophysics Data System (ADS)

Riaz, Muhammad; Earles, S. K.; Kadhim, Ahmed; Azzahrani, Ahmad

The computer analysis of tandem solar cell, c-Si/a-Si:H/μc-SiGe, is studied within Lumerical FDTD/Device 4.6. The optical characterization is performed in FDTD and then total generation rate is transported into DEVICE for electrical characterization. The electrical characterization of the solar cell is carried out in DEVICE. The design is implemented by staking three sub cells with band gap of 1.12eV, 1.50eV and 1.70eV, respectively. First, single junction solar cell with both a-Si and μc-SiGe absorbing layers are designed and compared. The thickness for both layers are kept the same. In a single junction, solar cell with a-Si absorbing layer, the fill factor and the efficiency are noticed as FF = 78.98%, and η = 6.03%. For μc-SiGe absorbing layer, the efficiency and fill factor are increased as η = 7.06% and FF = 84.27%, respectively. Second, for tandem thin film solar cell c-Si/a-Si:H/μc-SiGe, the fill factor FF = 81.91% and efficiency η = 9.84% have been noticed. The maximum efficiency for both single junction thin film solar cell c-Si/μc-SiGe and tandem solar cell c-Si/a-Si:H/μc-SiGe are improved with check board surface design for light trapping.

Crater Wall and Floor

NASA Image and Video Library

2003-02-18

The impact crater observed in this NASA Mars Odyssey image taken in Terra Cimmeria suggests sediments have filled the crater due to the flat and smooth nature of the floor compared to rougher surfaces at higher elevations.

School Protective Factors and Substance Use Among Lesbian, Gay, and Bisexual Adolescents in California Public Schools.

PubMed

De Pedro, Kris Tunac; Esqueda, Monica Christina; Gilreath, Tamika D

2017-06-01

The majority of studies examining substance use among lesbian, gay, and bisexual (LGB) youth have focused on a wide array of risk factors (e.g., victimization). Few studies have explored the protective role of schools. This study aims to fill this gap in the literature and inform programs aimed at reducing substance use among LGB youth. More specifically, this study explores the extent to which school connectedness and support from teachers and other adults at school are associated with substance use among LGB youth in school and within the past 30 days. A secondary analysis of the 2013-2015 California Healthy Kids Survey (CHKS) was conducted to examine associations between school protective factors (i.e., school connectedness and adult support) and substance use among LGB youth, above and beyond a key risk factor, school victimization. The study outcomes were past 30-day and in-school use of cigarettes, alcohol, marijuana, inhalants, prescription pain medication, and other illegal drugs. Overall, school connectedness and school adult support were associated with lower odds of substance use. For example, higher levels of school connectedness were associated with 22% decreased odds of past 30-day inhalant use (adjusted odds ratio [AOR] = 0.78; 95% confidence interval [CI] = 0.72-0.86), and 25% decreased odds of past 30-day prescription pain medication use (AOR = 0.75; 95% CI = 0.69-0.82). Higher levels of adult support in school were also associated with 17% decreased odds of marijuana use on school property in the past 30 days (AOR = 0.83; 95% CI = 0.77-0.91). The results indicate a need for substance use prevention programs that integrate school connectedness and adult support in school.

[Effects of cropping patterns on photosynthesis characteristics of summer maize and its utilization of solar and heat resources].

PubMed

Zhu, Yuan-Gang; Dong, Shu-Ting; Zhang, Ji-Wang; Liu, Peng; Yang, Jin-Sheng; Jia, Chun-Lan; Liu, Jing-Guo; Li, Deng-Hai

2010-06-01

In order to investigate the effects of interplanting and direct seeding on the photosynthesis characteristics of summer maize and its utilization of solar and heat resources, two summer maize cultivars (Zhengdan 958 and Denghai 661) were planted in the farmlands of Denghai Seed Co. Ltd in Laizhou City of Shandong Province, with 67500 plants x hm(-2) and three sowing dates. The above-ground biomass, plant growth rate, leaf area index, and net photosynthetic rate per ear leaf were measured to reveal the photosynthesis characteristics of test cultivars. In the meantime, the characters of grain-filling were simulated by Richards' model, and the solar resource utilization efficiency of the cultivars was calculated, in combining with meteorological data. Comparing with interplanting, direct seeding increased the grain yield by 1.17%-3.33%, but decreased the thousand-grain weight significantly. Growth stages were extended under earlier sowing. The leaf area index and net photosynthetic rate from flowering to 30 d after anthesis were significantly higher under direct seeding than under interplanting, but after then, they decreased faster. Direct seeding induced a higher accumulation of dry matter and a faster plant growth rate before and after flowering. Under direct seeding, the maximum grain-filling rate reached earlier, the starting potential was higher, but the grain-filling period, active grain-filling period, and W(max) were lower, compared with those under interplanting. Also under direct seeding, the total accumulative temperature and solar radiation during growth period decreased by 150-350 degrees C x d and 200-400 MJ x m(-2), respectively, but the solar resource utilization efficiency of grain increased by 10.5%-24.7%. All the results suggested that direct seeding was superior to interplanting for the summer maize production under field condition. In order to enhance solar and heat utilization efficiency and excavate yield potential, it would be essential to improve the leaf photosynthesis efficiency and postpone leaf aging.

[Doppler echocardiographic investigation of left ventricular diastolic function in preterm infants with and without a patent ductus arteriosus].

PubMed

Schmitz, L; Stiller, B; Koehne, P; Koch, H; Lange, P E

2004-01-01

We studied the influence of preload augmentation on Doppler-derived left ventricular diastolic function parameters in infants with a birth weight <1500 g. In 44 neonates with a closed duct and 29 neonates with an open ductus arteriosus a complete echocardiographic study including Doppler investigations of the mitral inflow signals and analysis of diastolic time intervals was performed. Neonates with an open duct had a lower median gestational age (27.1 vs. 29, P<0.01), a higher cardiac index (425 vs. 260 ml/min/kg, P<0.001), and a different M-mode left atrial to aortic diameter ratio (1.36 vs. 0.79, P<0.001), but birth weight, age at examination (6.6 vs. 7.9 days), and heart rate were similar compared to the neonates with a closed duct. Main differences in diastolic indexes existed in early and atrial filling integrals and peak velocities, early filling acceleration time, and isovolumic relaxation time. Most informative in neonates with an open ductus peak early filling velocity (41.2 vs. 30.4 cm, P<0.01) and peak atrial filling velocity (49.2 vs. 35.9, P<0.001) are higher, and isovolumic relaxation time is shorter (45 vs. 53 ms, P<0.001) than in closed duct peers. Isovolumic relaxation time is inversely correlated with the cardiac index (R = -0.78). These parameter changes can be interpreted as incipient left ventricular diastolic failure in extremely low birth weight infants in the presence of a preload challenge. The coincidence of higher peak velocities with a shortened isovolumic relaxation time is very likely a result of left atrial pressure elevation. Preload mismatch has to be considered in preterm infants with a persistent ductus arteriosus. The results of this study can be helpful to find the indication for PDA-closure and to adjust volume replacement therapy, and catecholamine medication to a level appropriate for the individual cardiac performance.